Effects of oblique air flow on burning rates of square ethanol pool fires.

PubMed

Tao, Changfa; He, Yaping; Li, Yuan; Wang, Xishi

2013-09-15

The effects of downward airflow on the burning rate and/or burning intensity of square alcohol pool fires for different airflow speeds and directions have been studied experimentally in an inclined wind tunnel. An interesting flame-wrapping phenomenon, caused by impingement of air flow, was observed. The mass burning intensity was found to increase with the airflow speed and the impinging angle. The fuel pan rim temperatures were also measured to study the effect of wind direction and speed on heat transfer from the flame to the fuel source. A model based on heat transfer analysis was developed to correlate the burning intensity with the pan rim characteristic temperature. A good correlation was established between the model results and the experimental results. Copyright © 2013 Elsevier B.V. All rights reserved.

Combustion of a Polymer (PMMA) Sphere in Microgravity

NASA Technical Reports Server (NTRS)

Yang, Jiann C.; Hamins, Anthony; Donnelly, Michelle K.

1999-01-01

A series of low gravity, aircraft-based, experiments was conducted to investigate the combustion of supported thermoplastic polymer spheres under varying ambient conditions. The three types of thermoplastic investigated were polymethylmethacrylate (PMMA), polypropylene (PP). and polystyrene (PS). Spheres with diameters ranging from 2 mm to 6.35 mm were tested. The total initial pressure varied from 0.05 MPa to 0. 15 MPa whereas the ambient oxygen concentration varied from 19 % to 30 % (by volume). The ignition system consisted of a pair of retractable energized coils. Two CCD cameras recorded the burning histories of the spheres. The video sequences revealed a number of dynamic events including bubbling and sputtering, as well as soot shell formation and break-up during combustion of the spheres at reduced gravity. The ejection of combusting material from the burning spheres represents a fire hazard that must be considered at reduced gravity. The ejection process was found to be sensitive to polymer type. All average burning rates were measured to increase with initial sphere diameter and oxygen concentration, whereas the initial pressure had little effect. The three thermoplastic types exhibited different burning characteristics. For the same initial conditions, the burning rate of PP was slower than PMMA, whereas the burning rate of PS was comparable to PMMA. The transient diameter of the burning thermoplastic exhibited two distinct periods: an initial period (enduring approximately half of the total burn duration) when the diameter remained approximately constant, and a final period when the square of the diameter linearly decreased with time. A simple homogeneous two-phase model was developed to understand the changing diameter of the burning sphere. Its value is based on a competition between diameter reduction due to mass loss from burning and sputtering, and diameter expansion due to the processes of swelling (density decrease with heating) and bubble growth. The model relies on empirical parameters for input, such as the burning rate and the duration of the initial and final burning periods.

A One-Dimensional Global-Scaling Erosive Burning Model Informed by Blowing Wall Turbulence

NASA Technical Reports Server (NTRS)

Kibbey, Timothy P.

2014-01-01

A derivation of turbulent flow parameters, combined with data from erosive burning test motors and blowing wall tests results in erosive burning model candidates useful in one-dimensional internal ballistics analysis capable of scaling across wide ranges of motor size. The real-time burn rate data comes from three test campaigns of subscale segmented solid rocket motors tested at two facilities. The flow theory admits the important effect of the blowing wall on the turbulent friction coefficient by using blowing wall data to determine the blowing wall friction coefficient. The erosive burning behavior of full-scale motors is now predicted more closely than with other recent models.

Development of a reactive burn model based on an explicit viscoplastic pore collapse model

NASA Astrophysics Data System (ADS)

Bouton, E.; Lefrançois, A.; Belmas, R.

2017-01-01

The aim of this study is to develop a reactive burn model based upon a microscopic hot spot model to compute the shock-initiation of pressed TATB high explosives. Such a model has been implemented in a lagrangian hydrodynamic code. In our calculations, 8 pore radii, ranging from 40 nm to 0.63 μm, have been taken into account and the porosity fraction associated to each void radius has been deduced from the Ultra-Small-Angle X-ray Scattering measurements (USAXS) for PBX-9502. The last parameter of our model is a burn rate that depends on three variables. The first two are the reaction progress variable and the lead shock pressure, the last one is the chemical reaction site number produced in the flow and calculated by the microscopic model. This burn rate has been calibrated by fitting pressure, velocity profiles and run distances to detonation. As the computed results are in close agreement with the measured ones, this model is able to perform a wide variety of numerical simulations including single, double shock waves and the desensitization phenomenon.

Turbulent Burning Velocities of Two-Component Fuel Mixtures of Methane, Propane and Hydrogen

NASA Astrophysics Data System (ADS)

Kido, Hiroyuki; Nakahara, Masaya; Hashimoto, Jun; Barat, Dilmurat

In order to clarify the turbulent burning velocity of multi-component fuel mixtures, both lean and rich two-component fuel mixtures, in which methane, propane and hydrogen were used as fuels, were prepared while maintaining the laminar burning velocity approximately constant. A distinct difference in the measured turbulent burning velocity at the same turbulence intensity is observed for two-component fuel mixtures having different addition rates of fuel, even the laminar burning velocities are approximately the same. The burning velocities of lean mixtures change almost constantly as the rate of addition changes, whereas the burning velocities of the rich mixtures show no such tendency. This trend can be explained qualitatively based on the mean local burning velocity, which is estimated by taking into account the preferential diffusion effect for each fuel component. In addition, a model of turbulent burning velocity proposed for single-component fuel mixtures may be applied to two-component fuel mixtures by considering the estimated mean local burning velocity of each fuel.

Validation of numerical simulations for nano-aluminum composite solid propellants

NASA Astrophysics Data System (ADS)

Yan, Allen H.

2011-12-01

Nano-aluminum is of interest as an energetic additive in composite solid propellant formulations for its demonstrated ability to increase combustion efficiency and burning rate. However, due to the current cost of nano-aluminum and the associated safety risks associated with propellant testing, it may not always be practical to spend the time and effort to mix, cast, and thoroughly evaluate the burning rate of a new formulation. To provide an alternative method of determining this parameter, numerical methods have been developed to predict the performance of nano-aluminum composite propellants, but these codes still require thorough validation before application. For this purpose, six propellant compositions were formulated, fully characterized, and burn rates were measured at several pressures between 34.0 and 129.3 atmospheres at room temperature, 20°C, and at an elevated temperature of 71.1°C in order to test the code's ability to predict pressure dependent burn rate and temperature sensitivity. To ensure the most accurate model possible, special emphasis was placed on characterizing the size distribution of the constituent nano-aluminum and ammonium perchlorate powders through optical diffraction or optical imaging techniques. Experimental burn rate is compared to the propellant combustion model and shows excellent agreement within 5% for a range of formulations and pressures, however under other conditions the model deviates by as much as 21%. An analysis of the results suggests that the current framework of the numerical model is unable to accurately simulate all the combustion physics of high aluminum content propellants, and suggestions for improvements are identified.

Emulation of Condensed Fuel Flames Using a Burning Rate Emulator (BRE) in Microgravity

NASA Technical Reports Server (NTRS)

Markan, A.; Quintiere, J. G.; Sunderland, P. B.; De Ris, J. L.; Stocker, D. P.

2017-01-01

The Burning Rate Emulator (BRE) is a gaseous fuel burner developed to emulate the burning of condensed phase fuels. The current study details several tests at the NASA Glenn 5-s drop facility to test the BRE technique in microgravity conditions. The tests are conducted for two burner diameters, 25 mm and 50 mm respectively, with methane and ethylene as the fuels. The ambient pressure, oxygen content and fuel flow rate are additional parameters. The microgravity results exhibit a nominally hemispherical flame with decelerating growth and quasi-steady heat flux after about 5 seconds. The BRE burner was evaluated with a transient analysis to assess the extent of steady-state achieved. The burning rate and flame height recorded at the end of the drop are correlated using two steady-state purely diffusive models. A higher burning rate for the bigger burner as compared to theory indicates the significance of gas radiation. The effect of the ambient pressure and oxygen concentration on the heat of gasification are also examined.

Long term outcomes data for the Burns Registry of Australia and New Zealand: Is it feasible?

PubMed

Gabbe, Belinda J; Cleland, Heather; Watterson, Dina M; Schrale, Rebecca; McRae, Sally; Parker, Christine; Taggart, Susan; Edgar, Dale W

2015-12-01

Incorporating routine and standardised collection of long term outcomes following burn into burn registries would improve the capacity to quantify burn burden and evaluate care. To evaluate methods for collecting the long term functional and quality of life outcomes of burns patients and establish the feasibility of implementing these outcomes into a multi-centre burns registry. Five Burns Registry of Australia and New Zealand (BRANZ) centres participated in this prospective, longitudinal study. Patients admitted to the centres between November 2009 and November 2010 were followed-up at 1, 6, 12 and 24-months after injury using measures of burn specific health, health status, fatigue, itch and return to work. Participants in the study were compared to BRANZ registered patients at the centres over the study timeframe to identify participation bias, predictors of successful follow-up were established using a Generalised Estimating Equation model, and the completion rates by mode of administration were assessed. 463 patients participated in the study, representing 24% of all BRANZ admissions in the same timeframe. Compared to all BRANZ patients in the same timeframe, the median %TBSA and hospital length of stay was greater in the study participants. The follow-up rates were 63% at 1-month, 47% at 6-months; 40% at 12-months, and 21% at 24-months after injury, and there was marked variation in follow-up rates between the centres. Increasing age, greater %TBSA and opt-in centres were associated with greater follow-up. Centres which predominantly used one mode of administration experienced better follow-up rates. The low participation rates, high loss to follow-up and responder bias observed indicate that greater consideration needs to be given to alternative models for follow-up, including tailoring the follow-up protocol to burn severity or type. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Evidence of erosive burning in shuttle solid rocket motor

NASA Technical Reports Server (NTRS)

Martin, C. L.

1983-01-01

Known models of Shuttle Solid Rocket Motor (SRM) performance have failed to produce pressure-time traces which accurately matched actual motor performance, especially during the first 5 seconds after ignition and during the last quarter of web burn time. Efforts to compensate for these differences in model reconstruction and actual performance resulted in resorting to the use of a Burning Anomaly Rate Function (BARF). It was suspected that propellant erosive burning was primarily responsible for the variation of model from actual results. The three dimensional Hercules Grain Design and Internal Ballistics Evaluation Program was made operational and slightly modified and an extensive trial and error effort was begun to test the hypothesis of erosive burning as an explanation of the burning anomaly. It was found that introduction of erosive burning (using Green's erosive burning equation) over portions of the aft segment grain and above a threshold gas Mach number did, in fact, give excellent agreement with the actual motor trace.

History, Epidemic Evolution, and Model Burn-In for a Network of Annual Invasion: Soybean Rust.

PubMed

Sanatkar, M R; Scoglio, C; Natarajan, B; Isard, S A; Garrett, K A

2015-07-01

Ecological history may be an important driver of epidemics and disease emergence. We evaluated the role of history and two related concepts, the evolution of epidemics and the burn-in period required for fitting a model to epidemic observations, for the U.S. soybean rust epidemic (caused by Phakopsora pachyrhizi). This disease allows evaluation of replicate epidemics because the pathogen reinvades the United States each year. We used a new maximum likelihood estimation approach for fitting the network model based on observed U.S. epidemics. We evaluated the model burn-in period by comparing model fit based on each combination of other years of observation. When the miss error rates were weighted by 0.9 and false alarm error rates by 0.1, the mean error rate did decline, for most years, as more years were used to construct models. Models based on observations in years closer in time to the season being estimated gave lower miss error rates for later epidemic years. The weighted mean error rate was lower in backcasting than in forecasting, reflecting how the epidemic had evolved. Ongoing epidemic evolution, and potential model failure, can occur because of changes in climate, host resistance and spatial patterns, or pathogen evolution.

Impact of facial burns: relationship between depressive symptoms, self-esteem and scar severity.

PubMed

Hoogewerf, Cornelis Johannes; van Baar, Margriet Elisabeth; Middelkoop, Esther; van Loey, Nancy Elisa

2014-01-01

This study assessed the role of self-reported facial scar severity as a possible influencing factor on self-esteem and depressive symptoms in patients with facial burns. A prospective multicentre cohort study with a 6 months follow-up was conducted including 132 patients with facial burns. Patients completed the Patient and Observer Scar Assessment Scale, the Rosenberg Self-esteem Scale and the Hospital Anxiety and Depression Scale. Structural Equation Modeling was used to assess the relations between depressive symptoms, self-esteem and scar severity. The model showed that patient-rated facial scar severity was not predictive for self-esteem and depressive symptoms six months post-burn. There was, however, a significant relationship between early depressive symptoms and both patient-rated facial scar severity and subsequent self-esteem. The variables in the model accounted for 37% of the variance in depressive symptoms six months post-burn and the model provided a moderately well-fitting representation of the data. The study suggests that self-esteem and depressive symptoms were not affected by self-reported facial scar severity but that earlier depressive symptoms were indicative for a more severe self-reported facial scar rating. Therefore, routine psychological screening during hospitalisation is recommended in order to identify patients at risk and to optimise their treatment. Copyright © 2014 Elsevier Inc. All rights reserved.

Improving Long-term Post-wildfire hydrologic simulations using ParFlow

NASA Astrophysics Data System (ADS)

Lopez, S. R.; Kinoshita, A. M.

2015-12-01

Wildfires alter the natural hydrologic processes within a watershed. After vegetation is burned, the combustion of organic material and debris settles into the soil creating a hydrophobic layer beneath the soil surface with varying degree of thickness and depth. Vegetation regrowth rates vary as a function of radiative exposure, burn severity, and precipitation patterns. Hydrologic models used by the Burned Area Emergency Response (BAER) teams use input data and model calibration constraints that are generally either one-dimensional, empirically-based models, or two-dimensional, conceptually-based models with lumped parameter distributions. These models estimate runoff measurements at the watershed outlet; however, do not provide a distributed hydrologic simulation at each point within the watershed. This work uses ParFlow, a three-dimensional, distributed hydrologic model to (1) correlate burn severity with hydrophobicity, (2) evaluate vegetation recovery rate on water components, and (3) improve flood prediction for managers to help with resource allocation and management operations in burned watersheds. ParFlow is applied to Devil Canyon (43 km2) in San Bernardino, California, which was 97% burned in the 2003 Old Fire. The model set-up uses a 30m-cell size resolution over a 6.7 km by 6.4 km lateral extent. The subsurface reaches 30 m and is assigned a variable cell thickness. Variable subsurface thickness allows users to explicitly consider the degree of recovery throughout the stages of regrowth. Burn severity maps from remotely sensed imagery are used to assign initial hydrophobic layer parameters and thickness. Vegetation regrowth is represented with satellite an Enhanced Vegetation Index. Pre and post-fire hydrologic response is evaluated using runoff measurements at the watershed outlet, and using water component (overland flow, lateral flow, baseflow) measurements.

The contribution of charcoal burning to the rise and decline of suicides in Hong Kong from 1997-2007.

PubMed

Law, C K; Yip, Paul S F; Caine, Eric D

2011-09-01

There has been scant research exploring the relationship between choice of method (means) of self-inflicted death, and broader social or contextual factors. The recent emergence and growth of suicide using carbon monoxide poisoning resulting from burning charcoal in an enclosed space (hereafter, "charcoal burning") was related to an increase in the overall suicide rate in Hong Kong. The growth of this method coincided with changing economic conditions. This paper expands upon previous work to explore possible relationships further. This study aims to discern the role of charcoal burning in overall suicide rate transition during times of both economic recession and expansion, as captured in the unemployment rate of Hong Kong, and to examine whether there was evidence of an effect from means-substitution. Age and gender specific suicide rates in Hong Kong by suicide methods from 1997 to 2007 were calculated. To model the transition of suicide rate by different methods, Poisson regression analyses were employed. Charcoal burning constituted 18.3% of all suicides, 88% of which involved individuals drawn from the middle years (25-59) of life. During both periods of rising and declining unemployment, charcoal burning played an important role in the changing suicide rates, and this effect was most prominent among for those in their middle years. Means-substitution was found among the married women during the period of rate advancement (1997-2003). Compared to others, working-age adults preferentially selected carbon monoxide poisoning from charcoal burning.

Sodium and sulfur release and recapture during black liquor burning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, W.J.; Iisa, K.; Wag, K.

1995-08-01

The objective of this study was to provide data on sulfur and sodium volatilization during black liquor burning, and on SO2 capture by solid sodium carbonate and sodium chloride. This data was interpreted and modeled into rate equations suitable for use in computational models for recovery boilers.

Fiber-Supported Droplet Combustion Experiment-2

NASA Technical Reports Server (NTRS)

Colantonio, Renato O.

1998-01-01

A major portion of the energy produced in the world today comes from the burning of liquid hydrocarbon fuels in the form of droplets. Understanding the fundamental physical processes involved in droplet combustion is not only important in energy production but also in propulsion, in the mitigation of combustion-generated pollution, and in the control of the fire hazards associated with handling liquid combustibles. Microgravity makes spherically symmetric combustion possible, allowing investigators to easily validate their droplet models without the complicating effects of gravity. The Fiber-Supported Droplet Combustion (FSDC-2) investigation was conducted in the Microgravity Glovebox facility of the shuttles' Spacelab during the reflight of the Microgravity Science Laboratory (MSL- 1R) on STS-94 in July 1997. FSDC-2 studied fundamental phenomena related to liquid fuel droplet combustion in air. Pure fuels and mixtures of fuels were burned as isolated single and duo droplets with and without forced air convection. FSDC-2 is sponsored by the NASA Lewis Research Center, whose researchers are working in cooperation with several investigators from industry and academia. The rate at which a droplet burns is important in many commercial applications. The classical theory of droplet burning assumes that, for an isolated, spherically symmetric, single-fuel droplet, the gas-phase combustion processes are much faster than the droplet surface regression rate and that the liquid phase is at a uniform temperature equal to the boiling point. Recent, more advanced models predict that both the liquid and gas phases are unsteady during a substantial portion of the droplet's burning history, thus affecting the instantaneous and average burning rates, and that flame radiation is a dominant mechanism that can extinguish flames in a microgravity environment. FSDC-2 has provided well-defined, symmetric droplet burning data including radiative emissions to validate these theoretical models for heptane, decane, ethanol, and methanol fuels. Since most commercial combustion systems burn droplets in a convective environment, data were obtained without and with convective flow over the burning droplet (see the following photos).

Model of ASTM Flammability Test in Microgravity: Iron Rods

NASA Technical Reports Server (NTRS)

Steinberg, Theodore A; Stoltzfus, Joel M.; Fries, Joseph (Technical Monitor)

2000-01-01

There is extensive qualitative results from burning metallic materials in a NASA/ASTM flammability test system in normal gravity. However, this data was shown to be inconclusive for applications involving oxygen-enriched atmospheres under microgravity conditions by conducting tests using the 2.2-second Lewis Research Center (LeRC) Drop Tower. Data from neither type of test has been reduced to fundamental kinetic and dynamic systems parameters. This paper reports the initial model analysis for burning iron rods under microgravity conditions using data obtained at the LERC tower and modeling the burning system after ignition. Under the conditions of the test the burning mass regresses up the rod to be detached upon deceleration at the end of the drop. The model describes the burning system as a semi-batch, well-mixed reactor with product accumulation only. This model is consistent with the 2.0-second duration of the test. Transient temperature and pressure measurements are made on the chamber volume. The rod solid-liquid interface melting rate is obtained from film records. The model consists of a set of 17 non-linear, first-order differential equations which are solved using MATLAB. This analysis confirms that a first-order rate, in oxygen concentration, is consistent for the iron-oxygen kinetic reaction. An apparent activation energy of 246.8 kJ/mol is consistent for this model.

A mesoscopic reaction rate model for shock initiation of multi-component PBX explosives.

PubMed

Liu, Y R; Duan, Z P; Zhang, Z Y; Ou, Z C; Huang, F L

2016-11-05

The primary goal of this research is to develop a three-term mesoscopic reaction rate model that consists of a hot-spot ignition, a low-pressure slow burning and a high-pressure fast reaction terms for shock initiation of multi-component Plastic Bonded Explosives (PBX). Thereinto, based on the DZK hot-spot model for a single-component PBX explosive, the hot-spot ignition term as well as its reaction rate is obtained through a "mixing rule" of the explosive components; new expressions for both the low-pressure slow burning term and the high-pressure fast reaction term are also obtained by establishing the relationships between the reaction rate of the multi-component PBX explosive and that of its explosive components, based on the low-pressure slow burning term and the high-pressure fast reaction term of a mesoscopic reaction rate model. Furthermore, for verification, the new reaction rate model is incorporated into the DYNA2D code to simulate numerically the shock initiation process of the PBXC03 and the PBXC10 multi-component PBX explosives, and the numerical results of the pressure histories at different Lagrange locations in explosive are found to be in good agreements with previous experimental data. Copyright © 2016 Elsevier B.V. All rights reserved.

Propagation of Cutaneous Thermal Injury: A Mathematical Model

PubMed Central

Xue, Chuan; Chou, Ching-Shan; Kao, Chiu-Yen; Sen, Chandan K.; Friedman, Avner

2012-01-01

Cutaneous burn wounds represent a significant public health problem with 500,000 patients per year in the U.S. seeking medical attention. Immediately after skin burn injury, the volume of the wound burn expands due to a cascade of chemical reactions, including lipid peroxidation chain reactions. Based on these chemical reactions, the present paper develops for the first time a three-dimensional mathematical model to quantify the propagation of tissue damage within 12 hours post initial burn. We use the model to investigate the effect of supplemental antioxidant vitamin E for stopping the propagation. We show, for example, that if the production rate of vitamin E is increased, post burn, by five times the natural production in a healthy tissue, then this would slow down the lipid peroxide propagation by at least 50%. Our model is formulated in terms of differential equations, and sensitivity analysis is performed on the parameters to ensure the robustness of the results. PMID:22211391

Numerical and experimental study of thermal explosions in LX-10 and PBX 9501: Influence of thermal damage on deflagration processes

NASA Astrophysics Data System (ADS)

Tringe, J. W.; Kercher, J. R.; Springer, H. K.; Glascoe, E. A.; Levie, H. W.; Hsu, P.; Willey, T. M.; Molitoris, J. D.

2013-07-01

We employ in-situ flash x-ray imaging, together with a detailed multiphase convective burn model, to demonstrate how explosives' binder characteristics influence the burning processes in thermal explosions. Our study focuses on the HMX-based explosives LX-10 and PBX 9501. While the HMX (cyclotetramethylene-tetranitramine) crystallite size distributions for these two explosives are nearly identical before heating, our experiments and simulations indicate that after heating, variations result due to differences in binder composition. Post-ignition flash x-ray images reveal that the average density decreases at late times more rapidly in PBX 9501 than LX-10, suggesting a faster conductive burning rate in PBX-9501. Heated permeability measurements in LX-10 and PBX 9501 demonstrate that the binder system characteristics influence the evolution of connected porosity. Once ignited, connected porosity provides pathways for product gas heating ahead of the reaction front and additional surface area for burning, facilitating the transition from conductive to convective burning modes. A multiphase convective burn model implemented in the ALE3D code is used to better understand the influence on burn rates of material properties such as porosity and effective thermally damaged particle size. In this context, particles are defined as gas-impermeable binder-coated crystallites and agglomerations with a set of effective radii reff. Model results demonstrate quantitative agreement with containment wall velocity for confined PBX 9501 and LX-10, and qualitative agreement with density as a function of position in the burning explosive. The model predicts a decrease in post-ignition containment wall velocity with larger radii in reff. These experimental data and model results together provide insight into the initiation and propagation of the reaction wave that defines the convective burn front in HMX-based explosives, a necessary step toward predicting violence under a broad range of conditions.

Application of mixing-controlled combustion models to gas turbine combustors

NASA Technical Reports Server (NTRS)

Nguyen, Hung Lee

1990-01-01

Gas emissions were studied from a staged Rich Burn/Quick-Quench Mix/Lean Burn combustor were studied under test conditions encountered in High Speed Research engines. The combustor was modeled at conditions corresponding to different engine power settings, and the effect of primary dilution airflow split on emissions, flow field, flame size and shape, and combustion intensity, as well as mixing, was investigated. A mathematical model was developed from a two-equation model of turbulence, a quasi-global kinetics mechanism for the oxidation of propane, and the Zeldovich mechanism for nitric oxide formation. A mixing-controlled combustion model was used to account for turbulent mixing effects on the chemical reaction rate. This model assumes that the chemical reaction rate is much faster than the turbulent mixing rate.

Evaluating alternative prescribed burning policies to reduce net economic damages from wildfire

Treesearch

D. Evan Mercer; Jeffrey P. Prestemon; David T. Butry; John M. Pye

2007-01-01

We estimate a wildfire risk model with a new measure of wildfire output, intensity-weighted risk and use it in Monte Carlo simulations to estimate welfare changes from alternative prescribed burning policies. Using Volusia County, Florida as a case study, an annual prescribed burning rate of 13% of all forest lands maximizes net welfare; ignoring the effects on...

Solid propellant rocket motor internal ballistics performance variation analysis, phase 3

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Foster, W. A., Jr.; Murph, J. E.; Adams, G. W., Jr.

1977-01-01

Results of research aimed at improving the predictability of off nominal internal ballistics performance of solid propellant rocket motors (SRMs) including thrust imbalance between two SRMs firing in parallel are reported. The potential effects of nozzle throat erosion on internal ballistic performance were studied and a propellant burning rate low postulated. The propellant burning rate model when coupled with the grain deformation model permits an excellent match between theoretical results and test data for the Titan IIIC, TU455.02, and the first Space Shuttle SRM (DM-1). Analysis of star grain deformation using an experimental model and a finite element model shows the star grain deformation effects for the Space Shuttle to be small in comparison to those of the circular perforated grain. An alternative technique was developed for predicting thrust imbalance without recourse to the Monte Carlo computer program. A scaling relationship used to relate theoretical results to test results may be applied to the alternative technique of predicting thrust imbalance or to the Monte Carlo evaluation. Extended investigation into the effect of strain rate on propellant burning rate leads to the conclusion that the thermoelastic effect is generally negligible for both steadily increasing pressure loads and oscillatory loads.

Burn leads to long-term elevated admissions to hospital for gastrointestinal disease in a West Australian population based study.

PubMed

Stevenson, Andrew W; Randall, Sean M; Boyd, James H; Wood, Fiona M; Fear, Mark W; Duke, Janine M

2017-05-01

While the most obvious impact of burn is on the skin, systemic responses also occur after burn, including intestinal inflammation. The objective of this study was to assess if burns are associated with increased long-term admissions for gastrointestinal diseases. A population-based longitudinal study using linked hospital morbidity and death data from Western Australia was undertaken of adults aged at least 15 years when hospitalized for a first burn (n=20,561) in 1980-2012. A frequency matched non-injury comparison cohort was randomly selected from Western Australia's birth registrations and electoral roll (n=80,960). Crude admission rates and summed days in hospital for digestive diseases were calculated. Negative binomial and Cox proportional hazards regression modeling were used to generate incidence rate ratios (IRR) and hazard ratios (HR), respectively. After adjustment for demographic factors and pre-existing health status, the burn cohort had 1.54 times (95% confidence interval (CI): 1.47-1.62) as many admissions and almost three times the number of days in hospital with a digestive system diagnosis (IRR, 95% CI: 2.90, 2.60-3.25) than the uninjured cohort. Significantly elevated adjusted post-burn incident rates were identified, with the risk decreasing with increasing time: in the first month (HR, 95% CI: 3.02, 1.89-4.82), from one month to five years (HR, 95% CI: 1.42, 1.31-1.54), and from five to twenty years after burn (HR, 95% CI: 1.13, 1.06-1.20). Findings of increased hospital admission rates and prolonged length of hospital stay for gastrointestinal diseases in the burn cohort provide evidence to support that burns have effects that persist long after the initial injury. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Scar formation following excisional and burn injuries in a red Duroc pig model.

PubMed

Blackstone, Britani N; Kim, Jayne Y; McFarland, Kevin L; Sen, Chandan K; Supp, Dorothy M; Bailey, J Kevin; Powell, Heather M

2017-08-01

Scar research is challenging because rodents do not naturally form excessive scars, and burn depth, size, and location cannot be controlled in human longitudinal studies. The female, red Duroc pig model has been shown to form robust scars with biological and anatomical similarities to human hypertrophic scars. To more closely mimic the mode of injury, recreate the complex chemical milieu of the burn wound environment and enhance scar development, an animal model of excessive burn-induced scarring was developed and compared with the more commonly used model, which involves excisional wounds created via dermatome. Standardized, full-thickness thermal wounds were created on the dorsum of female, red Duroc pigs. Wounds for the dermatome model were created using two different total dermatome settings: ∼1.5 mm and ≥ 1.9 mm. Results from analysis over 150 days showed that burn wounds healed at much slower rate and contracted more significantly than dermatome wounds of both settings. The burn scars were hairless, had mixed pigmentation, and displayed fourfold and twofold greater excess erythema values, respectively, compared with ∼1.5 mm and ≥ 1.9 mm deep dermatome injuries. Burn scars were less elastic, less pliable, and weaker than scars resulting from excisional injuries. Decorin and versican gene expression levels were elevated in the burn group at day 150 compared with both dermatome groups. In addition, transforming growth factor-beta 1 was significantly up-regulated in the burn group vs. the ∼1.5 mm deep dermatome group at all time points, and expression remained significantly elevated vs. both dermatome groups at day 150. Compared with scars from dermatome wounds, the burn scar model described here demonstrates greater similarity to human hypertrophic scar. Thus, this burn scar model may provide an improved platform for studying the pathophysiology of burn-related hypertrophic scarring, investigating current anti-scar therapies, and development of new strategies with greater clinical benefit. © 2017 by the Wound Healing Society.

Increased admissions for diabetes mellitus after burn.

PubMed

Duke, Janine M; Randall, Sean M; Fear, Mark W; Boyd, James H; O'Halloran, Emily; Rea, Suzanne; Wood, Fiona M

2016-12-01

Currently, limited long-term data on hyperglycaemia and insulin sensitivity in burn patients are available and the data that do exist are primarily related to paediatric severe burns. The aim of this study was to assess if burn is associated with increased post-burn admissions for diabetes mellitus. A population-based longitudinal study using linked hospital morbidity and death data from Western Australia was undertaken of all persons hospitalized for a first burn (n=30,997) in 1980-2012 and a frequency matched non-injury comparison cohort, randomly selected from Western Australia's birth registrations and electoral roll (n=123,399). Crude admission rates and summed length of stay for diabetes mellitus were calculated. Negative binomial and Cox proportional hazards regression modelling were used to generate incidence rate ratios (IRR) and hazard ratios (HR), respectively. After adjustment for socio-demographic factors and pre-existing health status, the burn cohort had 2.21 times (95% Confidence Interval (CI): 1.36-1.56) as many admissions and almost three times the number of days in hospital with a diabetes mellitus diagnosis (IRR, 95% CI: 2.94, 2.12-4.09) than the uninjured cohort. Admission rates were significantly elevated for those burned during childhood (<18 years, IRR, 95% CI: 2.65, 1.41-4.97) and adulthood (≥18 years, IRR, 95% CI: 2.12, 1.76-2.55). Incident admissions were significantly elevated in the burn cohort during the first 5 years post-burn when compared with the uninjured (HR, 95% CI: 1.96, 1.46-2.64); no significant difference was found beyond 5 years post-burn (HR, 95% CI: 1.08, 0.82-1.41). Findings of increased hospital admission rates and prolonged length of hospital stay for diabetes mellitus in the burn cohort provide evidence that burns have longer term effects on blood glucose and insulin regulation after wound healing. The first five years after burn discharge appears to be a critical period with significantly elevated incident admissions for diabetes mellitus during this time. Results would suggest prolonged clinical management after discharge and or wound healing to minimise post-burn admissions for diabetes mellitus is required. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

The First 3D Simulations of Carbon Burning in a Massive Star

NASA Astrophysics Data System (ADS)

Cristini, A.; Meakin, C.; Hirschi, R.; Arnett, D.; Georgy, C.; Viallet, M.

2017-11-01

We present the first detailed three-dimensional hydrodynamic implicit large eddy simulations of turbulent convection for carbon burning. The simulations start with an initial radial profile mapped from a carbon burning shell within a 15 M⊙ stellar evolution model. We considered 4 resolutions from 1283 to 10243 zones. These simulations confirm that convective boundary mixing (CBM) occurs via turbulent entrainment as in the case of oxygen burning. The expansion of the boundary into the surrounding stable region and the entrainment rate are smaller at the bottom boundary because it is stiffer than the upper boundary. The results of this and similar studies call for improved CBM prescriptions in 1D stellar evolution models.

Burning rate for steel-cased, pressed binderless HMX

NASA Technical Reports Server (NTRS)

Fifer, R. A.; Cole, J. E.

1980-01-01

The burning behavior of pressed binderless HMX laterally confined in 6.4 mm i.d. steel cases was measured over the pressure range 1.45 to 338 MPa in a constant pressure strand burner. The measured regression rates are compared to those reported previously for unconfined samples. It is shown that lateral confinement results in a several-fold decrease in the regression rate for the coarse particle size HMX above the transition to super fast regression. For class E samples, confinement shifts the transition to super fast regression from low pressure to high pressure. These results are interpreted in terms of the previously proposed progressive deconsolidation mechanism. Preliminary holographic photography and closed bomb tests are also described. Theoretical one dimensional modeling calculations were carried out to predict the expected flame height (particle burn out distance) as a function of particle size and pressure for binderless HMX burning by a progressive deconsolidation mechanism.

An LNG release, transport, and fate model system for marine spills.

PubMed

Spaulding, Malcolm L; Swanson, J Craig; Jayko, Kathy; Whittier, Nicole

2007-02-20

LNGMAP, a fully integrated, geographic information based modular system, has been developed to predict the fate and transport of marine spills of LNG. The model is organized as a discrete set of linked algorithms that represent the processes (time dependent release rate, spreading, transport on the water surface, evaporation from the water surface, transport and dispersion in the atmosphere, and, if ignited, burning and associated radiated heat fields) affecting LNG once it is released into the environment. A particle-based approach is employed in which discrete masses of LNG released from the source are modeled as individual masses of LNG or spillets. The model is designed to predict the gas mass balance as a function of time and to display the spatial and temporal evolution of the gas (and radiated energy field). LNGMAP has been validated by comparisons to predictions of models developed by ABS Consulting and Sandia for time dependent point releases from a draining tank, with and without burning. Simulations were in excellent agreement with those performed by ABS Consulting and consistent with Sandia's steady state results. To illustrate the model predictive capability for realistic emergency scenarios, simulations were performed for a tanker entering Block Island Sound. Three hypothetical cases were studied: the first assumes the vessel continues on course after the spill starts, the second that the vessel stops as soon as practical after the release begins (3 min), and the third that the vessel grounds at the closest site practical. The model shows that the areas of the surface pool and the incident thermal radiation field (with burning) are minimized and dispersed vapor cloud area (without burning) maximized if the vessel continues on course. For this case the surface pool area, with burning, is substantially smaller than for the without burning case because of the higher mass loss rate from the surface pool due to burning. Since the vessel speed substantially exceeds the spill spreading rate, both the thermal radiation fields and surface pool trail the vessel. The relative directions and speeds of the wind and vessel movement govern the orientation of the dispersed plume. If the vessel stops, the areas of the surface pool and incident radiation field (with burning) are maximized and the dispersed cloud area (without burning) minimized. The longer the delay in stopping the vessel, the smaller the peak values are for the pool area and the size of the thermal radiation field. Once the vessel stops, the spill pool is adjacent to the vessel and moving down current. The thermal radiation field is oriented similarly. These results may be particularly useful in contingency planning for underway vessels.

Nitramine propellants. [gun propellant burning rate

NASA Technical Reports Server (NTRS)

Cohen, N. S.; Strand, L. D. (Inventor)

1978-01-01

Nitramine propellants without a pressure exponent shift in the burning rate curves are prepared by matching the burning rate of a selected nitramine or combination of nitramines within 10% of burning rate of a plasticized active binder so as to smooth out the break point appearance in the burning rate curve.

Fire behavior, weather, and burn severity of the 2007 Anaktuvuk River tundra fire, North Slope, Alaska

Treesearch

Benjamin M. Jones; Crystal A. Kolden; Randi Jandt; John T. Abatzoglu; Frank Urban; Christopher D. Arp

2009-01-01

In 2007, the Anaktuvuk River Fire (ARF) became the largest recorded tundra fire on the North Slope of Alaska. The ARF burned for nearly three months, consuming more than 100,000 ha. At its peak in early September, the ARF burned at a rate of 7000 ha d-1. The conditions potentially responsible for this large tundra fire include modeled record high...

Optimization of Equation of State and Burn Model Parameters for Explosives

NASA Astrophysics Data System (ADS)

Bergh, Magnus; Wedberg, Rasmus; Lundgren, Jonas

2017-06-01

A reactive burn model implemented in a multi-dimensional hydrocode can be a powerful tool for predicting non-ideal effects as well as initiation phenomena in explosives. Calibration against experiment is, however, critical and non-trivial. Here, a procedure is presented for calibrating the Ignition and Growth Model utilizing hydrocode simulation in conjunction with the optimization program LS-OPT. The model is applied to the explosive PBXN-109. First, a cylinder expansion test is presented together with a new automatic routine for product equation of state calibration. Secondly, rate stick tests and instrumented gap tests are presented. Data from these experiments are used to calibrate burn model parameters. Finally, we discuss the applicability and development of this optimization routine.

Determinants of skeletal muscle protein turnover following severe burn trauma in children.

PubMed

Malagaris, Ioannis; Herndon, David N; Polychronopoulou, Efstathia; Rontoyanni, Victoria G; Andersen, Clark R; Suman, Oscar E; Porter, Craig; Sidossis, Labros S

2018-06-04

Burns remain the fifth cause of non-fatal pediatric injuries globally, with muscle cachexia being a hallmark of the stress response to burns. Burn-induced muscle wasting is associated with morbidity, yet the determinants of muscle protein catabolism in response to burn trauma remains unclear. Our objective was to determine the effect of patient and injury characteristics on muscle protein kinetics in burn patients. This retrospective, observational study was performed using protein kinetic data from pediatric patients who had severe burns (>30% of the total body surface area burned) and underwent cross-limb stable isotope infusions between 1999 and 2008 as part of prospective clinical trials. Mixed multiple regression models were used to assess associations between patient/injury characteristics and muscle protein fractional synthesis rate (FSR), net balance (NB), and rates of phenylalanine appearance (Ra; index of protein breakdown) and disappearance (Rd; index of protein synthesis) across the leg. A total of 268 patients who underwent 499 studies were analyzed. Increasing time post injury was associated with greater FSR (p < 0.001) and NB (p = 0.01). Males were more catabolic than females (as indicated by lower NB, p = 0.04 and greater Ra, p = 0.008), a consequence of higher protein breakdown rather than lower synthesis. Increasing burn size was associated with higher protein synthesis rate (as indicated by higher FSR, p = 0.019) and higher protein breakdown rates (as indicated by greater Ra, p = 0.001). FSR was negatively associated with age (p < 0.001). Data from this large patient cohort show that injury severity, sex, and time post injury influence skeletal muscle wasting in burned children. These findings suggest that individual patient characteristics should be considered when devising therapies to improve the acute care and rehabilitation of burn survivors. Copyright © 2018 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Design of a model to predict surge capacity bottlenecks for burn mass casualties at a large academic medical center.

PubMed

Abir, Mahshid; Davis, Matthew M; Sankar, Pratap; Wong, Andrew C; Wang, Stewart C

2013-02-01

To design and test a model to predict surge capacity bottlenecks at a large academic medical center in response to a mass-casualty incident (MCI) involving multiple burn victims. Using the simulation software ProModel, a model of patient flow and anticipated resource use, according to principles of disaster management, was developed based upon historical data from the University Hospital of the University of Michigan Health System. Model inputs included: (a) age and weight distribution for casualties, and distribution of size and depth of burns; (b) rate of arrival of casualties to the hospital, and triage to ward or critical care settings; (c) eligibility for early discharge of non-MCI inpatients at time of MCI; (d) baseline occupancy of intensive care unit (ICU), surgical step-down, and ward; (e) staff availability-number of physicians, nurses, and respiratory therapists, and the expected ratio of each group to patients; (f) floor and operating room resources-anticipating the need for mechanical ventilators, burn care and surgical resources, blood products, and intravenous fluids; (g) average hospital length of stay and mortality rate for patients with inhalation injury and different size burns; and (h) average number of times that different size burns undergo surgery. Key model outputs include time to bottleneck for each limiting resource and average waiting time to hospital bed availability. Given base-case model assumptions (including 100 mass casualties with an inter-arrival rate to the hospital of one patient every three minutes), hospital utilization is constrained within the first 120 minutes to 21 casualties, due to the limited number of beds. The first bottleneck is attributable to exhausting critical care beds, followed by floor beds. Given this limitation in number of patients, the temporal order of the ensuing bottlenecks is as follows: Lactated Ringer's solution (4 h), silver sulfadiazine/Silvadene (6 h), albumin (48 h), thrombin topical (72 h), type AB packed red blood cells (76 h), silver dressing/Acticoat (100 h), bismuth tribromophenate/Xeroform (102 h), and gauze bandage rolls/Kerlix (168 h). The following items do not precipitate a bottleneck: ventilators, topical epinephrine, staplers, foams, antimicrobial non-adherent dressing/Telfa types A, B, or O blood. Nurse, respiratory therapist, and physician staffing does not induce bottlenecks. This model, and similar models for non-burn-related MCIs, can serve as a real-time estimation and management tool for hospital capacity in the setting of MCIs, and can inform supply decision support for disaster management.

Long-term musculoskeletal morbidity after adult burn injury: a population-based cohort study

PubMed Central

Randall, Sean M; Fear, Mark W; Wood, Fiona M; Rea, Suzanne; Boyd, James H; Duke, Janine M

2015-01-01

Objective To investigate if adults who are hospitalised for a burn injury have increased long-term hospital use for musculoskeletal diseases. Design A population-based retrospective cohort study using linked administrative health data from the Western Australian Data Linkage System. Subjects Records of 17 753 persons aged at least 20 years when hospitalised for a first burn injury in Western Australia during the period 1980–2012, and 70 758 persons who were age and gender-frequency matched with no injury admissions randomly selected from Western Australia's electoral roll. Main outcome measures Admission rates and cumulative length of stay for musculoskeletal diseases. Negative binomial and Cox proportional hazards regression modelling were used to generate incidence rate ratios (IRR) and HRs with 95% CIs, respectively. Results After adjustment for pre-existing health status and demographic characteristics, the burn cohort had almost twice the hospitalisation rate for a musculoskeletal condition (IRR, 95% CI 1.98, 1.86 to 2.10), and spent 3.70 times as long in hospital with a musculoskeletal diagnosis (95% CI 3.10 to 4.42) over the 33-year period, than the uninjured comparison cohort. Adjusted survival analyses of incident post-burn musculoskeletal disease admissions found significant increases for the 15-year post burn discharge period (0–6 months: HR, 95% CI 2.51, 2.04 to 3.11; 6 months–2 years: HR, 95% CI 1.77, 1.53 to 2.05; 2–15 years: HR, 95% CI 1.32, 1.23 to 1.42). Incident admission rates were significantly elevated for 20 years post-burn for minor and severe burn injury for a range of musculoskeletal diseases that included arthropathies, dorsopathies, osteopathies and soft tissue disorders. Conclusions Minor and severe burn injuries were associated with significantly increased post-burn incident admission rates, long-term hospital use and prolonged length of stay for a range of musculoskeletal diseases. Further research is required that facilitates identification of at-risk patients and appropriate treatment pathways, to reduce the long-term morbidity associated with burns. PMID:26362668

Effects of Gas-Phase Radiation and Detailed Kinetics on the Burning and Extinction of a Solid Fuel

NASA Technical Reports Server (NTRS)

Rhatigan, Jennifer L.

2001-01-01

This is the first attempt to analyze both radiation and detailed kinetics on the burning and extinction of a solid fuel in a stagnation-point diffusion flame. We present a detailed and comparatively accurate computational model of a solid fuel flame along with a quantitative study of the kinetics mechanism, radiation interactions, and the extinction limits of the flame. A detailed kinetics model for the burning of solid trioxane (a trimer of formaldehyde) is coupled with a narrowband radiation model, with carbon dioxide, carbon monoxide, and water vapor as the gas-phase participating media. The solution of the solid trioxane diffusion flame over the flammable regime is presented in some detail, as this is the first solution of a heterogeneous trioxane flame. We identify high-temperature and low-temperature reaction paths for the heterogeneous trioxane flame. We then compare the adiabatic solution to solutions that include Surface radiation only and gas-phase and surface radiation using a black surface model. The analysis includes discussion of detailed flame chemistry over the flammable regime and, in particular, at the low stretch extinction limit. We emphasize the low stretch regime of the radiatively participating flame, since this is the region representative of microgravity flames. When only surface radiation is included, two extinction limits exist (the blow-off limit, and the low stretch radiative limit), and the burning rate and maximum flame temperatures are lower, as expected. With the inclusion of surface and gas-phase radiation, results show that, while flame temperatures are lower, the burning rate of the trioxane diffusion flame may actually increase at low stretch rate due to radiative feedback from the flame to the surface.

What could have caused pre-industrial biomass burning emissions to exceed current rates?

NASA Astrophysics Data System (ADS)

van der Werf, G. R.; Peters, W.; van Leeuwen, T. T.; Giglio, L.

2012-08-01

Recent studies based on trace gas mixing ratios in ice cores and charcoal data indicate that biomass burning emissions over the past millennium exceeded contemporary emissions by up to a factor of 4 for certain time periods. This is surprising because various sources of biomass burning are linked with population density, which has increased over the past centuries. Here we have analyzed how emissions from several biomass burning sources could have fluctuated to yield emissions that are in correspondence with recent results based on ice core mixing ratios of carbon monoxide (CO) and its isotopic signature measured at South Pole station (SPO). Based on estimates of contemporary fire emissions and the TM5 chemical transport model, we found that CO mixing ratios at SPO are more sensitive to emissions from South America and Australia than from Africa, and are relatively insensitive to emissions from the Northern Hemisphere. We then explored how various biomass burning sources may have varied over the past centuries and what the resulting emissions and corresponding CO mixing ratio at SPO would be, using population density variations to reconstruct sources driven by humans (e.g. fuelwood burning) and a new model to relate savanna emissions to changes in fire return times. We found that to match the observed ice core CO data all savannas in the Southern Hemisphere had to burn annually, or bi-annually in combination with deforestation and slash and burn agriculture matching current levels despite much lower population densities and lack of machinery to aid the deforestation process. While possible, these scenarios are unlikely and in conflict with current literature. However, we do show the large potential for increased emissions from savannas in a pre-industrial world. This is mainly because in the past, fuel beds were probably less fragmented compared to the current situation; we show that the majority of savannas have not burned in the past 10 yr, even in Africa which is considered "the burning continent". Our new modelling results, together with existing literature, indicate that no definitive conclusions can be drawn about unprecedentedly high or low biomass burning rates from current data analyses.

Biomass burning aerosol over Romania using dispersion model and Calipso data

NASA Astrophysics Data System (ADS)

Nicolae, Victor; Dandocsi, Alexandru; Marmureanu, Luminita; Talianu, Camelia

2018-04-01

The purpose of the study is to analyze the seasonal variability, for the hot and cold seasons, of biomass burning aerosol observed over Romania using forward dispersion calculations based on FLEXPART model. The model was set up to use as input the MODIS fire data with a degree of confidence over 25% after transforming the emitted power in emission rate. The modelled aerosols in this setup was black carbon coated by organics. Distribution in the upper layers were compared to Calipso retrieval.

Shock Detector for SURF model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menikoff, Ralph

2016-01-11

SURF and its extension SURFplus are reactive burn models aimed at shock initiation and propagation of detonation waves in high explosives. A distinctive feature of these models is that the burn rate depends on the lead shock pressure. A key part of the models is an algorithm to detect the lead shock. Typically, shock capturing hydro algorithms have small oscillations behind a shock. Here we investigate how well the shock detection algorithm works for a nearly steady propagating detonation wave in one-dimension using the Eulerian xRage code.

Space Shuttle Five-Segment Booster (Short Course)

NASA Technical Reports Server (NTRS)

Graves, Stanley R.; Rudolphi, Michael (Technical Monitor)

2002-01-01

NASA is considering upgrading the Space Shuttle by adding a fifth segment (FSB) to the current four-segment solid rocket booster. Course materials cover design and engineering issues related to the Reusable Solid Rocket Motor (RSRM) raised by the addition of a fifth segment to the rocket booster. Topics cover include: four segment vs. five segment booster, abort modes, FSB grain design, erosive burning, enhanced propellant burn rate, FSB erosive burning model development and hardware configuration.

Solid Fuel Burning in Steady, Strained, Premixed Flow Fields: The Graphite/Air/Methane System

NASA Technical Reports Server (NTRS)

Egolfopoulos, Fokion N.; Wu, Ming-Shin (Technical Monitor)

2000-01-01

A detailed numerical investigation was conducted on the simultaneous burning of laminar premixed CH4/air flames and solid graphite in a stagnation flow configuration. The graphite and methane were chosen for this model, given that they are practical fuels and their chemical kinetics are considered as the most reliable ones among solid and hydrocarbon fuels, respectively. The simulation was performed by solving the quasi-one-dimensional equations of mass, momentum, energy, and species. The GRI 2.1 scheme was used for the gas-phase kinetics, while the heterogeneous kinetics were described by a six-step mechanism including stable and radical species. The effects of the graphite surface temperature, the gas-phase equivalence ratio, and the aerodynamic strain rate on the graphite burning rate and NO, production and destruction mechanisms were assessed. Results indicate that as the graphite temperature increases, its burning rate as well as the NO, concentration increase. Furthermore, it was found that by increasing the strain rate, the graphite burning rate increases as a result of the augmented supply of the gas-phase reactants towards the surface, while the NO, concentration decreases as a result of the reduced residence time. The effect of the equivalence ratio on both the graphite burning rate and NO, concentration was found to be non-monotonic and strongly dependent on the graphite temperature. Comparisons between results obtained for a graphite and a chemically inert surface revealed that the chemical activity of the graphite surface can result to the reduction of NO through reactions of the CH3, CH2, CH, and N radicals with NO.

Microscopic modelling of ignition and burning for well-arranged energetic crystals in response to drop-weight impact

NASA Astrophysics Data System (ADS)

Wu, Yanqing; Huang, Fenglei; Zhou, Min

2014-05-01

To probe into impact sensitivity of energetic crystals, a theoretical approach was developed for modelling a single layer of energetic particles between upper striker and below base. Considering the particle plasticity, frictional heating, melting, fracture, and chemical reaction at particle level, effects of loading parameters and sample characteristics on time-to-ignition and burning rate were compared. Finite element numerical simulations were simultaneously performed to provide supporting evidence for thermo-mechanical interactions among energetic particles. Once hot- spots ignition occurred during impact, the macrokinetics of chemical reactions were formulated by hot-spots density, combustion wave velocity and geometric factor. The resulting reaction may or may not develop into a violent event, may be sustained or be extinguished, which can be revealed from the subsequent burn reaction rate.

The effect of preexisting respiratory co-morbidities on burn outcomes☆

PubMed Central

Knowlin, Laquanda T.; Stanford, Lindsay B.; Cairns, Bruce A.; Charles, Anthony G.

2018-01-01

Introduction Burns cause physiologic changes in multiple organ systems in the body. Burn mortality is usually attributable to pulmonary complications, which can occur in up to 41% of patients admitted to the hospital after burn. Patients with preexisting comorbidities such as chronic lung diseases may be more susceptible. We therefore sought to examine the impact of preexisting respiratory disease on burn outcomes. Methods A retrospective analysis of patients admitted to a regional burn center from 2002–2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA, pre-existing comorbidities, smoker status, length of hospital stay, and days of mechanical ventilation. Bivariate analysis was performed and Cox regression modeling using significant variables was utilized to estimate hazard of progression to mechanical ventilation and mortality. Results There were a total of 7640 patients over the study period. Overall survival rate was 96%. 8% (n=672) had a preexisting respiratory disease. Chronic lung disease patients had a higher mortality rate (7%) compared to those without lung disease (4%, p<0.01). The adjusted Cox regression model to estimate the hazard of progression to mechanical ventilation in patients with respiratory disease was 21% higher compared to those without respiratory disease (HR=1.21, 95% CI=1.01–1.44). The hazard of progression to mortality is 56% higher (HR=1.56, 95% CI=1.10–2.19) for patients with pre-existing respiratory disease compared to those without respiratory disease after controlling for patient demographics and injury characteristics. Conclusion Preexisting chronic respiratory disease significantly increases the hazard of progression to mechanical ventilation and mortality in patients following burn. Given the increasing number of Americans with chronic respiratory diseases, there will likely be a greater number of individuals at risk for worse outcomes following burn. PMID:28341260

The effect of preexisting respiratory co-morbidities on burn outcomes.

PubMed

Knowlin, Laquanda T; Stanford, Lindsay B; Cairns, Bruce A; Charles, Anthony G

2017-03-01

Burns cause physiologic changes in multiple organ systems in the body. Burn mortality is usually attributable to pulmonary complications, which can occur in up to 41% of patients admitted to the hospital after burn. Patients with preexisting comorbidities such as chronic lung diseases may be more susceptible. We therefore sought to examine the impact of preexisting respiratory disease on burn outcomes. A retrospective analysis of patients admitted to a regional burn center from 2002-2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA, pre-existing comorbidities, smoker status, length of hospital stay, and days of mechanical ventilation. Bivariate analysis was performed and Cox regression modeling using significant variables was utilized to estimate hazard of progression to mechanical ventilation and mortality. There were a total of 7640 patients over the study period. Overall survival rate was 96%. 8% (n=672) had a preexisting respiratory disease. Chronic lung disease patients had a higher mortality rate (7%) compared to those without lung disease (4%, p<0.01). The adjusted Cox regression model to estimate the hazard of progression to mechanical ventilation in patients with respiratory disease was 21% higher compared to those without respiratory disease (HR=1.21, 95% CI=1.01-1.44). The hazard of progression to mortality is 56% higher (HR=1.56, 95% CI=1.10-2.19) for patients with pre-existing respiratory disease compared to those without respiratory disease after controlling for patient demographics and injury characteristics. Preexisting chronic respiratory disease significantly increases the hazard of progression to mechanical ventilation and mortality in patients following burn. Given the increasing number of Americans with chronic respiratory diseases, there will likely be a greater number of individuals at risk for worse outcomes following burn. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Satisfaction with life after burn: A Burn Model System National Database Study.

PubMed

Goverman, J; Mathews, K; Nadler, D; Henderson, E; McMullen, K; Herndon, D; Meyer, W; Fauerbach, J A; Wiechman, S; Carrougher, G; Ryan, C M; Schneider, J C

2016-08-01

While mortality rates after burn are low, physical and psychosocial impairments are common. Clinical research is focusing on reducing morbidity and optimizing quality of life. This study examines self-reported Satisfaction With Life Scale scores in a longitudinal, multicenter cohort of survivors of major burns. Risk factors associated with Satisfaction With Life Scale scores are identified. Data from the National Institute on Disability, Independent Living, and Rehabilitation Research (NIDILRR) Burn Model System (BMS) database for burn survivors greater than 9 years of age, from 1994 to 2014, were analyzed. Demographic and medical data were collected on each subject. The primary outcome measures were the individual items and total Satisfaction With Life Scale (SWLS) scores at time of hospital discharge (pre-burn recall period) and 6, 12, and 24 months after burn. The SWLS is a validated 5-item instrument with items rated on a 1-7 Likert scale. The differences in scores over time were determined and scores for burn survivors were also compared to a non-burn, healthy population. Step-wise regression analysis was performed to determine predictors of SWLS scores at different time intervals. The SWLS was completed at time of discharge (1129 patients), 6 months after burn (1231 patients), 12 months after burn (1123 patients), and 24 months after burn (959 patients). There were no statistically significant differences between these groups in terms of medical or injury demographics. The majority of the population was Caucasian (62.9%) and male (72.6%), with a mean TBSA burned of 22.3%. Mean total SWLS scores for burn survivors were unchanged and significantly below that of a non-burn population at all examined time points after burn. Although the mean SWLS score was unchanged over time, a large number of subjects demonstrated improvement or decrement of at least one SWLS category. Gender, TBSA burned, LOS, and school status were associated with SWLS scores at 6 months; scores at 12 months were associated with LOS, school status, and amputation; scores at 24 months were associated with LOS, school status, and drug abuse. In this large, longitudinal, multicenter cohort of burn survivors, satisfaction with life after burn was consistently lower than that of non-burn norms. Furthermore mean SWLS scores did not improve over the two-year follow-up period. This study demonstrates the need for continued efforts to improve patient-centered long term satisfaction with life after burn. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Aluminum agglomeration involving the second mergence of agglomerates on the solid propellants burning surface: Experiments and modeling

NASA Astrophysics Data System (ADS)

Ao, Wen; Liu, Xin; Rezaiguia, Hichem; Liu, Huan; Wang, Zhixin; Liu, Peijin

2017-07-01

The agglomeration of aluminum particles usually occurs on the burning surface of aluminized composite propellants. It leads to low propellant combustion efficiency and high two-phase flow losses. To reach a thorough understanding of aluminum agglomeration behaviors, agglomeration processes, and particles size distribution of Al/AP/RDX/GAP propellants were studied by using a cinephotomicrography experimental technique, under 5 MPa. Accumulation, aggregation, and agglomeration phenomena of aluminum particles have been inspected, as well as the flame asymmetry of burning agglomerates. Results reveals that the dependency of the mean and the maximum agglomeration diameter to the burning rate and the virgin aluminum size have the same trend. A second-time mergence of multiple agglomerates on the burning surface is unveiled. Two typical modes of second mergence are concluded, based upon vertical and level movement of agglomerates, respectively. The latter mode is found to be dominant and sometimes a combination of the two modes may occur. A new model of aluminum agglomeration on the burning surface of composite propellants is derived to predict the particulates size distribution with a low computational amount. The basic idea is inspired from the well-known pocket models. The pocket size of the region formed by adjacent AP particles is obtained through scanning electron microscopy of the propellant cross-section coupled to an image processing method. The second mergence mechanism, as well as the effect of the burning rate on the agglomeration processes, are included in the present model. The mergence of two agglomerates is prescribed to occur only if their separation distance is less than a critical value. The agglomerates size distribution resulting from this original model match reasonably with the experimental data. Moreover, the present model gives superior results for mean agglomeration diameter compared to common empirical and pocket models. The average prediction error is lower than 5% for the four propellants tested. Results of this study are expected to provide better insight and enrich in the theoretical frame of aluminum agglomeration.

Effect of crib dimensions on burning rate

Treesearch

S. McAllister; M. Finney

2013-01-01

The burning rate of unconfined cribs has long been identified to occur in two regimes: the densely-packed regime where the burning rate is proportional to the crib porosity and the loosely-packed regime where the burning rate is independent of porosity. Though the cribs used to define these burning regimes were primarily cubic in dimension, there are seemingly endless...

Investigation of critical burning of fuel droplets

NASA Technical Reports Server (NTRS)

Allison, C. B.; Canada, G. S.; Faeth, G. M.

1972-01-01

Measurements were made on the burning of liquid hydrazine, MMH, and UDMH in a combustion gas environment. The experimental range of these tests involved gas temperatures of 1660-2530 K, oxygen concentrations of 0-42% by mass and droplet diameters (employing both droplets and porous spheres) of 0.11-1.91 cm. at atmospheric pressure. A simplified hybrid combustion theory was developed which was found to correlate the present results as well as the experimental measurements of other investigators. Measurements were also made of the monopropellant strand burning rates and liquid surface temperatures of a number of nitrate ester fuels and hydrazine at elevated pressures. The temperature measurements for the nitrate esters were found to be in good agreement with a theoretical model which allowed for gas solubility in the liquid phase at high pressures. Experimental results were also obtained on the burning rates and liquid surface temperatures of a number of paraffin and alcohol fuels burning in air pressures up to 72 atm. For these tests, the fuels were burned from porous spheres in a natural convection environment. Initial findings on a pressurized flat flame burner are also described as well as the design of an oscillatory combustion apparatus to test the response of burning liquid fuels.

Solid-propellant rocket motor internal ballistic performance variation analysis, phase 2

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Foster, W. A., Jr.

1976-01-01

The Monte Carlo method was used to investigate thrust imbalance and its first time derivative throughtout the burning time of pairs of solid rocket motors firing in parallel. Results obtained compare favorably with Titan 3 C flight performance data. Statistical correlations of the thrust imbalance at various times with corresponding nominal trace slopes suggest several alternative methods of predicting thrust imbalance. The effect of circular-perforated grain deformation on internal ballistics is discussed, and a modified design analysis computer program which permits such an evaluation is presented. Comparisons with SRM firings indicate that grain deformation may account for a portion of the so-called scale factor on burning rate between large motors and strand burners or small ballistic test motors. Thermoelastic effects on burning rate are also investigated. Burning surface temperature is calculated by coupling the solid phase energy equation containing a strain rate term with a model of gas phase combustion zone using the Zeldovich-Novozhilov technique. Comparisons of solutions with and without the strain rate term indicate a small but possibly significant effect of the thermoelastic coupling.

An Experimental Study on Burning Characteristics of n-Heptane/Ethanol Mixture Pool Fires in a Reduced Scaled Tunnel

NASA Astrophysics Data System (ADS)

Yozgatligil, Ahmet; Shafee, Sina

2016-11-01

Fire accidents in recent decades have drawn attention to safety issues associated with the design, construction and maintenance of tunnels. A reduced scale tunnel model constructed based on Froude scaling technique is used in the current work. Mixtures of n-heptane and ethanol are burned with ethanol volumetric fraction up to 30 percent and the longitudinal ventilation velocity varying from 0.5 to 2.5 m/s. The burning rates of the pool fires are measured using a precision load cell. The heat release rates of the fires are calculated according to oxygen calorimetry method and the temperature distributions inside the tunnel are also measured. Results of the experiments show that the ventilation velocity variation has a significant effect on the pool fire burning rate, smoke temperature and the critical ventilation velocity. With increased oxygen depletion in case of increased ethanol content of blended pool fires, the quasi-steady heat release rate values tend to increase as well as the ceiling temperatures while the combustion duration decreases.

Do burns increase the severity of terror injuries?

PubMed

Peleg, Kobi; Liran, Alon; Tessone, Ariel; Givon, Adi; Orenstein, Arie; Haik, Josef

2008-01-01

The use of explosives and suicide bombings has become more frequent since October 2000. This change in the nature of terror attacks has marked a new era in the Israeli-Palestinian conflict. We previously reported that the incidence of thermal injuries has since risen. However, the rise in the incidence of burns among victims of terror was proportionate to the rise in the incidence of burns among all trauma victims. This paper presents data from the Israeli National Trauma Registry during the years 1997--2003, to compare the severity of injuries and outcome (mortality rates) in terror victims with and without burn injuries. We also compare the severity of injuries and outcome (mortality rates) for patients with terror-attack related burns to non terror-attack related burns during the same period. Data was obtained from the Israeli National Trauma Registry for all patients admitted to 8 to 10 hospitals in Israel between 1997 and 2003. We analyzed and compared demographic and clinical characteristics of 219 terror-related burn patients (terror/burn), 2228 terror patients with no associated burns (Terror/no-burn) and 6546 non terror related burn patients (burn/no-terror). Severity of injuries was measured using the injury severity score, and burn severity by total body surface percentage indices. Admission rates to Intensive Care Units (ICU) and total length of hospitalization were also used to measure severity of injuries. In-hospital mortality rates were used to indicate outcome. Of burn/terror patients, 87.2% suffered other accompanying injuries, compared with 10.4% of burn/no-terror patients. Of burn/terror patients, 49.8% were admitted to ICU compared with only 11.9% of burn/no-terror patients and 23.8% of no-burn/terror patients. Mean length of hospital stay was 18.5 days for the terror/burn group compared with 11.1 days for the burn/no-terror group and 9.5 days for the terror/no-burn group. Burn/terror patients had a significantly higher injury severity score compared with the other groups. In-hospital mortality rate for the burn/no-terror group was 3.4%. The burn/terror group had a mortality rate of 6.4% which was similar to the no-burn/terror group (6.6%). Terror-attack injuries with accompanying burns have a more complex presentation, are of higher severity, and are associated with increased length of hospital stay and a higher ICU admissions rate, compared with terror-attack injuries without burns and non terror-attack related burns. However, mortality rates in terror-attack injuries are not affected by burns.

Long term mortality in critically ill burn survivors.

PubMed

Nitzschke, Stephanie; Offodile, Anaeze C; Cauley, Ryan P; Frankel, Jason E; Beam, Andrew; Elias, Kevin M; Gibbons, Fiona K; Salim, Ali; Christopher, Kenneth B

2017-09-01

Little is known about long term survival risk factors in critically ill burn patients who survive hospitalization. We hypothesized that patients with major burns who survive hospitalization would have favorable long term outcomes. We performed a two center observational cohort study in 365 critically ill adult burn patients who survived to hospital discharge. The exposure of interest was major burn defined a priori as >20% total body surface area burned [TBSA]. The modified Baux score was determined by age + %TBSA+ 17(inhalational injury). The primary outcome was all-cause 5year mortality based on the US Social Security Administration Death Master File. Adjusted associations were estimated through fitting of multivariable logistic regression models. Our final model included adjustment for inhalational injury, presence of 3rd degree burn, gender and the acute organ failure score, a validated ICU risk-prediction score derived from age, ethnicity, surgery vs. medical patient type, comorbidity, sepsis and acute organ failure covariates. Time-to-event analysis was performed using Cox proportional hazard regression. Of the cohort patients studied, 76% were male, 29% were non white, 14% were over 65, 32% had TBSA >20%, and 45% had inhalational injury. The mean age was 45, 92% had 2nd degree burns, 60% had 3rd degree burns, 21% received vasopressors, and 26% had sepsis. The mean TBSA was 20.1%. The mean modified Baux score was 72.8. Post hospital discharge 5year mortality rate was 9.0%. The 30day hospital readmission rate was 4%. Patients with major burns were significantly younger (41 vs. 47 years) had a significantly higher modified Baux score (89 vs. 62), and had significantly higher comorbidity, acute organ failure, inhalational injury and sepsis (all P<0.05). There were no differences in gender and the acute organ failure score between major and non-major burns. In the multivariable logistic regression model, major burn was associated with a 3 fold decreased odds of 5year post-discharge mortality compared to patients with TBSA<20% [OR=0.29 (95%CI 0.11-0.78; P=0.014)]. The adjusted model showed good discrimination [AUC 0.81 (95%CI 0.74-0.89)] and calibration (Hosmer-Lemeshow χ 2 P=0.67). Cox proportional hazard multivariable regression modeling, adjusting for inhalational injury, presence of 3rd degree burn, gender and the acute organ failure score, showed that major burn was predictive of lower mortality following hospital admission [HR=0.34 (95% CI 0.15-0.76; P=0.009)]. The modified Baux score was not predictive for mortality following hospital discharge [OR 5year post-discharge mortality=1.00 (95%CI 0.99-1.02; P=0.74); HR for post-discharge mortality=1.00 (95% CI 0.99-1.02; P=0.55)]. Critically ill patients with major burns who survive to hospital discharge have decreased 5year mortality compared to those with less severe burns. ICU Burn unit patients who survive to hospital discharge are younger with less comorbidities. The observed relationship is likely due to the relatively higher physiological reserve present in those who survive a Burn ICU course which may provide for a survival advantage during recovery after major burn. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

The treatment of mixing in core helium-burning models - III. Suppressing core breathing pulses with a new constraint on overshoot

NASA Astrophysics Data System (ADS)

Constantino, Thomas; Campbell, Simon W.; Lattanzio, John C.

2017-12-01

Theoretical predictions for the core helium burning phase of stellar evolution are highly sensitive to the uncertain treatment of mixing at convective boundaries. In the last few years, interest in constraining the uncertain structure of their deep interiors has been renewed by insights from asteroseismology. Recently, Spruit proposed a limit for the rate of growth of helium-burning convective cores based on the higher buoyancy of material ingested from outside the convective core. In this paper we test the implications of such a limit for stellar models with a range of initial mass and metallicity. We find that the constraint on mixing beyond the Schwarzschild boundary has a significant effect on the evolution late in core helium burning, when core breathing pulses occur and the ingestion rate of helium is fastest. Ordinarily, core breathing pulses prolong the core helium burning lifetime to such an extent that models are at odds with observations of globular cluster populations. Across a wide range of initial stellar masses (0.83 ≤ M/M⊙ ≤ 5), applying the Spruit constraint reduces the core helium burning lifetime because core breathing pulses are either avoided or their number and severity reduced. The constraint suggested by Spruit therefore helps to resolve significant discrepancies between observations and theoretical predictions. Specifically, we find improved agreement for R2 (the observed ratio of asymptotic giant branch to horizontal branch stars in globular clusters), the luminosity difference between these two groups, and in asteroseismology, the mixed-mode period spacing detected in red clump stars in the Kepler field.

Selective NOx Recirculation for Stationary Lean-Burn Natural Gas Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nigel N. Clark

Nitric oxide (NO) and nitrogen dioxide (NO2) generated by internal combustion (IC) engines are implicated in adverse environmental and health effects. Even though lean-burn natural gas engines have traditionally emitted lower oxides of nitrogen (NOx) emissions compared to their diesel counterparts, natural gas engines are being further challenged to reduce NOx emissions to 0.1 g/bhp-hr. The Selective NOx Recirculation (SNR) approach for NOx reduction involves cooling the engine exhaust gas and then adsorbing the NOx from the exhaust stream, followed by the periodic desorption of NOx. By sending the desorbed NOx back into the intake and through the engine, amore » percentage of the NOx can be decomposed during the combustion process. SNR technology has the support of the Department of Energy (DOE), under the Advanced Reciprocating Engine Systems (ARES) program to reduce NOx emissions to under 0.1 g/bhp-hr from stationary natural gas engines by 2010. The NO decomposition phenomenon was studied using two Cummins L10G natural gas fueled spark-ignited (SI) engines in three experimental campaigns. It was observed that the air/fuel ratio ({lambda}), injected NO quantity, added exhaust gas recirculation (EGR) percentage, and engine operating points affected NOx decomposition rates within the engine. Chemical kinetic model predictions using the software package CHEMKIN were performed to relate the experimental data with established rate and equilibrium models. The model was used to predict NO decomposition during lean-burn, stoichiometric burn, and slightly rich-burn cases with added EGR. NOx decomposition rates were estimated from the model to be from 35 to 42% for the lean-burn cases and from 50 to 70% for the rich-burn cases. The modeling results provided an insight as to how to maximize NOx decomposition rates for the experimental engine. Results from this experiment along with chemical kinetic modeling solutions prompted the investigation of rich-burn operating conditions, with added EGR to prevent preignition. It was observed that the relative air/fuel ratio, injected NO quantity, added EGR fraction, and engine operating points affected the NO decomposition rates. While operating under these modified conditions, the highest NO decomposition rate of 92% was observed. In-cylinder pressure data gathered during the experiments showed minimum deviation from peak pressure as a result of NO injections into the engine. A NOx adsorption system, from Sorbent Technologies, Inc., was integrated with the Cummins engine, comprised a NOx adsorbent chamber, heat exchanger, demister, and a hot air blower. Data were gathered to show the possibility of NOx adsorption from the engine exhaust, and desorption of NOx from the sorbent material. In order to quantify the NOx adsorption/desorption characteristics of the sorbent material, a benchtop adsorption system was constructed. The temperature of this apparatus was controlled while data were gathered on the characteristics of the sorbent material for development of a system model. A simplified linear driving force model was developed to predict NOx adsorption into the sorbent material as cooled exhaust passed over fresh sorbent material. A mass heat transfer analysis was conducted to analyze the possibility of using hot exhaust gas for the desorption process. It was found in the adsorption studies, and through literature review, that NO adsorption was poor when the carrier gas was nitrogen, but that NO in the presence of oxygen was adsorbed at levels exceeding 1% by mass of the sorbent. From the three experimental campaigns, chemical kinetic modeling analysis, and the scaled benchtop NOx adsorption system, an overall SNR system model was developed. An economic analysis was completed, and showed that the system was impractical in cost for small engines, but that economies of scale favored the technology.« less

Effects of normal acceleration on transient burning rate augmentation of an aluminized solid propellant

NASA Technical Reports Server (NTRS)

Northam, G. B.

1972-01-01

Instantaneous burning rate data for a polybutadiene acrylic acid propellant, containing 16 weight percent aluminum, were calculated from the pressure histories of a test motor with 96.77 sq cm of burning area and a 5.08-cm-thick propellant web. Additional acceleration tests were conducted with reduced propellant web thicknesses of 3.81, 2.54, and 1.27 cm. The metallic residue collected from the various web thickness tests was characterized by weight and shape and correlated with the instantaneous burning rate measurements. Rapid depressurization extinction tests were conducted in order that surface pitting characteristics due to localized increased burning rate could be correlated with the residue analysis and the instantaneous burning rate data. The acceleration-induced burning rate augmentation was strongly dependent on propellant distance burned, or burning time, and thus was transient in nature. The results from the extinction tests and the residue analyses indicate that the transient rate augmentation was highly dependent on local enhancement of the combustion zone heat feedback to the surface by the growth of molten residue particles on or just above the burning surface. The size, shape, and number density of molten residue particles, rather than the total residue weight, determined the acceleration-induced burning rate augmentation.

The effects of Q-nuclei on stellar burning

NASA Astrophysics Data System (ADS)

Boyd, R. N.; Turner, R. E.; Sur, B.; Rybarcyk, L.; Joseph, C.

1985-01-01

The effects of anomalous nuclei, Q-nuclei, on stellar burning are examined. The baryon binding energies, beta-decay properties, and thermonuclear reaction rates for the Q-nuclei suggest they could catalyze a cycle in which four protons are combined to form a 4He nucleus. The properties required of the Q-nuclei for them to solve the solar neutrino problem are determined. A solar modelling calculation was performed with Q-nuclei included, and several interesting results therefrom are compared to observations. Finally the solar neutrino detection rates for 71Ga and 115In detectors, in addition to that for 37Cl, are estimated when Q-nuclei are included in the solar burning.

Afterburning in spherical premixed turbulent explosions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley, D.; Lawes, M.; Scott, M.J.

1994-12-01

During the early stages of spherical turbulent flame propagation, more than half of the gas behind the visible flame front may be unburned. Previous models of the afterburning of the gas behind the apparent flame front have been extended in the present work, to include the effects of flame quenching, consequent upon localized flame stretch. The predictions of the model cover, the spatial and temporal variations of the fraction burned, the flame propagation rate, and the mass burning rate. They are all in dimensionless form and are well supported by associated experimental measurements in a fan-stirred bomb with controlled turbulence.more » The proportion of the gas that is unburned decreases with time and increases with the product of the Karlovitz stretch factor and the Lewis number. Simultaneous photographs were taken of the spherical schlieren image and of that due to Mie scattering from small seed particles in a thin laser sheet that sectioned the spherical flame. These clearly showed the amount of unburned gas within the sphere and, along with other evidence suggest laminar flamelet burning across a scale of distance which is close to the Taylor confirm the predictions of the fraction of gas unburned and of the rate at which it is burning.« less

Initial fuel temperature effects on burning rate of pool fire.

PubMed

Chen, Bing; Lu, Shou-Xiang; Li, Chang-Hai; Kang, Quan-Sheng; Lecoustre, Vivien

2011-04-15

The influence of the initial fuel temperature on the burning behavior of n-heptane pool fire was experimentally studied at the State Key Laboratory of Fire Science (SKLFS) large test hall. Circular pool fires with diameters of 100mm, 141 mm, and 200 mm were considered with initial fuel temperatures ranging from 290 K to 363 K. Burning rate and temperature distributions in fuel and vessel wall were recorded during the combustion. The burning rate exhibited five typical stages: initial development, steady burning, transition, bulk boiling burning, and decay. The burning rate during the steady burning stage was observed to be relatively independent of the initial fuel temperature. In contrast, the burning rate of the bulk boiling burning stage increases with increased initial fuel temperature. It was also observed that increased initial fuel temperature decreases the duration of steady burning stage. When the initial temperature approaches the boiling point, the steady burning stage nearly disappears and the burning rate moves directly from the initial development stage to the transition stage. The fuel surface temperature increases to its boiling point at the steady burning stage, shortly after ignition, and the bulk liquid reaches boiling temperature at the bulk boiling burning stage. No distinguished cold zone is formed in the fuel bed. However, boiling zone is observed and the thickness increases to its maximum value when the bulk boiling phenomena occurs. Copyright © 2011 Elsevier B.V. All rights reserved.

Experimental Investigations Of The Influence Of Pressure On Critical Extinction Conditions Of Laminar Nonpremixed Flames Burning Condensed Hydrocarbon Fuels, Jet Fuels, And Surrogates

DTIC Science & Technology

2014-10-25

cycloalkanes, aromatics, and alkenes [3,23–26]. On average, the composition by volume is approximately 60% alkanes, 20% cycloalkanes, 18% aromatics, and 2... alkenes [26]. Efforts to develop chemical-kinetic models that accurately describe the combustion of these practical fuels are critical to the development... method also allows for measurements of fuel mass burning rates by recording the required fuel feed rate to maintain the fuel cup level under steady

Biomass Burning Emissions from Fire Remote Sensing

NASA Technical Reports Server (NTRS)

Ichoku, Charles

2010-01-01

Knowledge of the emission source strengths of different (particulate and gaseous) atmospheric constituents is one of the principal ingredients upon which the modeling and forecasting of their distribution and impacts depend. Biomass burning emissions are complex and difficult to quantify. However, satellite remote sensing is providing us tremendous opportunities to measure the fire radiative energy (FRE) release rate or power (FRP), which has a direct relationship with the rates of biomass consumption and emissions of major smoke constituents. In this presentation, we will show how the satellite measurement of FRP is facilitating the quantitative characterization of biomass burning and smoke emission rates, and the implications of this unique capability for improving our understanding of smoke impacts on air quality, weather, and climate. We will also discuss some of the challenges and uncertainties associated with satellite measurement of FRP and how they are being addressed.

Spatial variability of steady-state infiltration into a two-layer soil system on burned hillslopes

USGS Publications Warehouse

Kinner, D.A.; Moody, J.A.

2010-01-01

Rainfall-runoff simulations were conducted to estimate the characteristics of the steady-state infiltration rate into 1-m2 north- and south-facing hillslope plots burned by a wildfire in October 2003. Soil profiles in the plots consisted of a two-layer system composed of an ash on top of sandy mineral soil. Multiple rainfall rates (18.4-51.2 mm h-1) were used during 14 short-duration (30 min) and 2 long-duration simulations (2-4 h). Steady state was reached in 7-26 min. Observed spatially-averaged steady-state infiltration rates ranged from 18.2 to 23.8 mm h-1 for north-facing and from 17.9 to 36.0 mm h-1 for south-facing plots. Three different theoretical spatial distribution models of steady-state infiltration rate were fit to the measurements of rainfall rate and steady-state discharge to provided estimates of the spatial average (19.2-22.2 mm h-1) and the coefficient of variation (0.11-0.40) of infiltration rates, overland flow contributing area (74-90% of the plot area), and infiltration threshold (19.0-26 mm h-1). Tensiometer measurements indicated a downward moving pressure wave and suggest that infiltration-excess overland flow is the runoff process on these burned hillslope with a two-layer system. Moreover, the results indicate that the ash layer is wettable, may restrict water flow into the underlying layer, and increase the infiltration threshold; whereas, the underlying mineral soil, though coarser, limits the infiltration rate. These results of the spatial variability of steady-state infiltration can be used to develop physically-based rainfall-runoff models for burned areas with a two-layer soil system. ?? 2010 Elsevier B.V.

Climate, wildfire, and erosion ensemble foretells more sediment in western USA watersheds

Treesearch

Joel B. Sankey; Jason Kreitler; Todd J. Hawbaker; Jason L. McVay; Mary Ellen Miller; Erich R. Mueller; Nicole M. Vaillant; Scott E. Lowe; Temuulen T. Sankey

2017-01-01

The area burned annually by wildfires is expected to increase worldwide due to climate change. Burned areas increase soil erosion rates within watersheds, which can increase sedimentation in downstream rivers and reservoirs. However, which watersheds will be impacted by future wildfires is largely unknown. Using an ensemble of climate, fire, and erosion models, we show...

Calibrating reaction rates for the CREST model

NASA Astrophysics Data System (ADS)

Handley, Caroline A.; Christie, Michael A.

2017-01-01

The CREST reactive-burn model uses entropy-dependent reaction rates that, until now, have been manually tuned to fit shock-initiation and detonation data in hydrocode simulations. This paper describes the initial development of an automatic method for calibrating CREST reaction-rate coefficients, using particle swarm optimisation. The automatic method is applied to EDC32, to help develop the first CREST model for this conventional high explosive.

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames.

PubMed

Singh, Ajay V; Gollner, Michael J

2016-06-01

Modeling the realistic burning behavior of condensed-phase fuels has remained out of reach, in part because of an inability to resolve the complex interactions occurring at the interface between gas-phase flames and condensed-phase fuels. The current research provides a technique to explore the dynamic relationship between a combustible condensed fuel surface and gas-phase flames in laminar boundary layers. Experiments have previously been conducted in both forced and free convective environments over both solid and liquid fuels. A unique methodology, based on the Reynolds Analogy, was used to estimate local mass burning rates and flame heat fluxes for these laminar boundary layer diffusion flames utilizing local temperature gradients at the fuel surface. Local mass burning rates and convective and radiative heat feedback from the flames were measured in both the pyrolysis and plume regions by using temperature gradients mapped near the wall by a two-axis traverse system. These experiments are time-consuming and can be challenging to design as the condensed fuel surface burns steadily for only a limited period of time following ignition. The temperature profiles near the fuel surface need to be mapped during steady burning of a condensed fuel surface at a very high spatial resolution in order to capture reasonable estimates of local temperature gradients. Careful corrections for radiative heat losses from the thermocouples are also essential for accurate measurements. For these reasons, the whole experimental setup needs to be automated with a computer-controlled traverse mechanism, eliminating most errors due to positioning of a micro-thermocouple. An outline of steps to reproducibly capture near-wall temperature gradients and use them to assess local burning rates and heat fluxes is provided.

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames

PubMed Central

Singh, Ajay V.; Gollner, Michael J.

2016-01-01

Modeling the realistic burning behavior of condensed-phase fuels has remained out of reach, in part because of an inability to resolve the complex interactions occurring at the interface between gas-phase flames and condensed-phase fuels. The current research provides a technique to explore the dynamic relationship between a combustible condensed fuel surface and gas-phase flames in laminar boundary layers. Experiments have previously been conducted in both forced and free convective environments over both solid and liquid fuels. A unique methodology, based on the Reynolds Analogy, was used to estimate local mass burning rates and flame heat fluxes for these laminar boundary layer diffusion flames utilizing local temperature gradients at the fuel surface. Local mass burning rates and convective and radiative heat feedback from the flames were measured in both the pyrolysis and plume regions by using temperature gradients mapped near the wall by a two-axis traverse system. These experiments are time-consuming and can be challenging to design as the condensed fuel surface burns steadily for only a limited period of time following ignition. The temperature profiles near the fuel surface need to be mapped during steady burning of a condensed fuel surface at a very high spatial resolution in order to capture reasonable estimates of local temperature gradients. Careful corrections for radiative heat losses from the thermocouples are also essential for accurate measurements. For these reasons, the whole experimental setup needs to be automated with a computer-controlled traverse mechanism, eliminating most errors due to positioning of a micro-thermocouple. An outline of steps to reproducibly capture near-wall temperature gradients and use them to assess local burning rates and heat fluxes is provided. PMID:27285827

Carbachol promotes gastrointestinal function during oral resuscitation of burn shock.

PubMed

Hu, Sen; Che, Jin-Wei; Tian, Yi-Jun; Sheng, Zhi-Yong

2011-04-07

To investigate the effect of carbachol on gastrointestinal function in a dog model of oral resuscitation for burn shock. Twenty Beagle dogs with intubation of the carotid artery, jugular vein and jejunum for 24 h were subjected to 35% total body surface area full-thickness burns, and were divided into three groups: no fluid resuscitation (NR, n = 10), in which animals did not receive fluid by any means in the first 24 h post-burn; oral fluid resuscitation (OR, n = 8), in which dogs were gavaged with glucose-electrolyte solution (GES) with volume and rate consistent with the Parkland formula; and oral fluid with carbachol group (OR/CAR, n = 8), in which dogs were gavaged with GES containing carbachol (20 μg/kg), with the same volume and rate as the OR group. Twenty-four hours after burns, all animals were given intravenous fluid replacement, and 72 h after injury, they received nutritional support. Hemodynamic and gastrointestinal parameters were measured serially with animals in conscious and cooperative state. The mean arterial pressure, cardiac output and plasma volume dropped markedly, and gastrointestinal tissue perfusion was reduced obviously after the burn injury in all the three groups. Hemodynamic parameters and gastrointestinal tissue perfusion in the OR and OR/CAR groups were promoted to pre-injury level at 48 and 72 h, respectively, while hemodynamic parameters in the NR group did not return to pre-injury level till 72 h, and gastrointestinal tissue perfusion remained lower than pre-injury level until 120 h post-burn. CO(2) of the gastric mucosa and intestinal mucosa blood flow of OR/CAR groups were 56.4 ± 4.7 mmHg and 157.7 ± 17.7 blood perfusion units (BPU) at 24 h post-burn, respectively, which were significantly superior to those in the OR group (65.8 ± 5.8 mmHg and 127.7 ± 11.9 BPU, respectively, all P < 0.05). Gastric emptying and intestinal absorption rates of GES were significantly reduced to the lowest level (52.8% and 23.7% of pre-injury levels) in the OR group at about 2 and 4 h post-burn, and did not return to 80% of pre-injury level until 24 h. In the first 24 h post-burn, the rate of gastric emptying and intestinal water absorption were elevated by a mean 15.7% and 11.5%, respectively, in the OR/CAR group compared with the OR group. At 5 days, the mortality in the NR group was 30% (3/10), 12.5% in the OR group (1/8), and none in the OR/CAR group. Carbachol had a beneficial effect on oral resuscitation of burn shock by promoting gastric emptying and intestinal absorption in our canine model.

High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Tan, N

2010-04-21

High pressure deflagration rate measurements of a unique ammonium perchlorate (AP) based propellant are required to design the base burn motor for a Raytheon weapon system. The results of these deflagration rate measurements will be key in assessing safety and performance of the system. In particular, the system may experience transient pressures on the order of 100's of MPa (10's kPSI). Previous studies on similar AP based materials demonstrate that low pressure (e.g. P < 10 MPa or 1500 PSI) burn rates can be quite different than the elevated pressure deflagration rate measurements (see References and HPP results discussed herein),more » hence elevated pressure measurements are necessary in order understand the deflagration behavior under relevant conditions. Previous work on explosives have shown that at 100's of MPa some explosives will transition from a laminar burn mechanism to a convective burn mechanism in a process termed deconsolidative burning. The resulting burn rates that are orders-of-magnitude faster than the laminar burn rates. Materials that transition to the deconsolidative-convective burn mechanism at elevated pressures have been shown to be considerably more violent in confined heating experiments (i.e. cook-off scenarios). The mechanisms of propellant and explosive deflagration are extremely complex and include both chemical, and mechanical processes, hence predicting the behavior and rate of a novel material or formulation is difficult if not impossible. In this work, the AP/HTPB based material, TAL-1503 (B-2049), was burned in a constant volume apparatus in argon up to 300 MPa (ca. 44 kPSI). The burn rate and pressure were measured in-situ and used to calculate a pressure dependent burn rate. In general, the material appears to burn in a laminar fashion at these elevated pressures. The experiment was reproduced multiple times and the burn rate law using the best data is B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} where B is the burn rate in mm/s and P is the pressure in units of MPa. Details of the experimental method, results and data analysis are discussed herein and briefly compared to other AP based materials that have been measured in this apparatus.« less

Numerical computation of Pop plot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menikoff, Ralph

The Pop plot — distance-of-run to detonation versus initial shock pressure — is a key characterization of shock initiation in a heterogeneous explosive. Reactive burn models for high explosives (HE) must reproduce the experimental Pop plot to have any chance of accurately predicting shock initiation phenomena. This report describes a methodology for automating the computation of a Pop plot for a specific explosive with a given HE model. Illustrative examples of the computation are shown for PBX 9502 with three burn models (SURF, WSD and Forest Fire) utilizing the xRage code, which is the Eulerian ASC hydrocode at LANL. Comparisonmore » of the numerical and experimental Pop plot can be the basis for a validation test or as an aid in calibrating the burn rate of an HE model. Issues with calibration are discussed.« less

Massage has no observable effect on distress in children with burns: A randomized, observer-blinded trial.

PubMed

van Dijk, Monique; O'Flaherty, Linda Anne; Hoedemaker, Tessa; van Rosmalen, Joost; Rode, Heinz

2018-02-01

In a previous observational study we found that massage therapy reduced anxiety and stress in pediatric burn patients. We aimed to test this effect in a randomized controlled trial. To determine whether (1) aromatherapy massage can provide relaxation to hospitalized children with burns; (2) massage with aromatherapy oil is more effective than without; and (3) massage sessions are more effective when repeated. Randomized controlled clinical trial with 3 arms conducted in a burns unit from April 2013 to December 2014 in Cape Town, South Africa. Massage with carrier oil, massage with aromatherapy oil, and standard nursing care only. Scores on the Muscle Tension Inventory (MTI) and Behavioral Relaxation Scale (BRS) to assess level of relaxation. Scores on the COMFORT behaviour scale and Numeric Rating Scale Distress to assess level of distress. Secondary outcomes were heart rate and oxygen saturation levels. Linear mixed models were used to determine the effect of condition and session number (1 to a maximum of 5 sessions per child) correcting for baseline outcomes of COMFORT behaviour scores and heart rates after sessions. Secondary analyses included the addition of sex, age, and total body surface area (TBSA) burned as covariates. We included 284 children aged 5 weeks to 13 years with TBSA burned between 10 and 45%. Two-thirds (65.5%) were under the age of 3 years. Mixed model analyses revealed no significant difference in reduction of COMFORT behavior scores (p=0.18), or heart rates (p=0.18) between the three study arms. These outcomes were also not associated with the session number (p=0.92 and p=0.13, respectively). Level of relaxation could not be reliably assessed with the MTI and BRS because 119 patients (41.9%) had bandages covering the larger part of the face, and in 40.1% of cases the child was not in the required position. Massage therapy with or without essential oil was not effective in reducing distress behavior or heart rate in hospitalized children with burns. Evaluating the effectiveness of massage in terms of relaxation proved difficult in young children. The Netherlands National Trial Registry: NRT3929. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Measurement of Solid Rocket Propellant Burning Rate Using X-ray Imaging

NASA Astrophysics Data System (ADS)

Denny, Matthew D.

The burning rate of solid propellants can be difficult to measure for unusual burning surface geometries, but X-ray imaging can be used to measure burning rate. The objectives of this work were to measure the baseline burning rate of an electrically-controlled solid propellant (ESP) formulation with real-time X-ray radiography and to determine the uncertainty of the measurements. Two edge detection algorithms were written to track the burning surface in X-ray videos. The edge detection algorithms were informed by intensity profiles of simulated 2-D X-ray images. With a 95% confidence level, the burning rates measured by the Projected-Slope Intersection algorithm in the two combustion experiments conducted were 0.0839 in/s +/-2.86% at an average pressure of 407 psi +/-3.6% and 0.0882 in/s +/-3.04% at 410 psi +/-3.9%. The uncertainty percentages were based on the statistics of a Monte Carlo analysis on burning rate.

Preparation of Partial-Thickness Burn Wounds in Rodents Using a New Experimental Burning Device.

PubMed

Sakamoto, Michiharu; Morimoto, Naoki; Ogino, Shuichi; Jinno, Chizuru; Kawaguchi, Atsushi; Kawai, Katsuya; Suzuki, Shigehiko

2016-06-01

The manual application of hot water or hot metal to an animal's skin surface is often used to prepare burn wound models. However, manual burn creation is subject to human variability. We developed a new device that can control the temperature, time, and pressure of contact to produce precise and reproducible animal burn wounds and investigated the conditions required to prepare various burn wounds using our new device. We prepared burn wounds on F344 rats using 3 contact times 2, 4, and 10 seconds using a stamp heated to 80°C. We observed the wound-healing process macroscopically and histologically and evaluated the burn depth using a laser speckle contrast-imaging device, which evaluated the blood flow of the wound. The changes in the burned area over time, tissue perfusion of the burn wounds, histological evaluation of the burn depth by hematoxylin-eosin and azocarmine and aniline blue staining, and the epithelialization rate (the ratio of the epithelialized area to the wound length) were evaluated on histological sections. Results indicated that the burn wounds prepared with contact times of 2, 4, and 10 seconds corresponded to superficial dermal burns, deep dermal burns, and full-thickness burns, respectively. We demonstrated that partial- and full-thickness burn wounds can be precisely and reproducibly created with our new automated burning device.

Modelling of pore coarsening in the high burn-up structure of UO2 fuel

NASA Astrophysics Data System (ADS)

Veshchunov, M. S.; Tarasov, V. I.

2017-05-01

The model for coalescence of randomly distributed immobile pores owing to their growth and impingement, applied by the authors earlier to consideration of the porosity evolution in the high burn-up structure (HBS) at the UO2 fuel pellet periphery (rim zone), was further developed and validated. Predictions of the original model, taking into consideration only binary impingements of growing immobile pores, qualitatively correctly describe the decrease of the pore number density with the increase of the fractional porosity, however notably underestimate the coalescence rate at high burn-ups attained in the outmost region of the rim zone. In order to overcome this discrepancy, the next approximation of the model taking into consideration triple impingements of growing pores was developed. The advanced model provides a reasonable consent with experimental data, thus demonstrating the validity of the proposed pore coarsening mechanism in the HBS.

Acoustic emission strand burning technique for motor burning rate prediction

NASA Technical Reports Server (NTRS)

Christensen, W. N.

1978-01-01

An acoustic emission (AE) method is being used to measure the burning rate of solid propellant strands. This method has a precision of 0.5% and excellent burning rate correlation with both subscale and large rocket motors. The AE procedure burns the sample under water and measures the burning rate from the acoustic output. The acoustic signal provides a continuous readout during testing, which allows complete data analysis rather than the start-stop clockwires used by the conventional method. The AE method helps eliminate such problems as inhibiting the sample, pressure increase and temperature rise, during testing.

Fracture admissions after burns: A retrospective longitudinal study.

PubMed

Duke, Janine M; Randall, Sean M; Fear, Mark W; Boyd, James H; Wood, Fiona M

2017-09-01

Severe burn triggers systemic responses that result in reduced muscle mass and changes in bone formation, with recent evidence also suggesting systemic effects on bone after minor burns. The aim of this study was to assess if people hospitalised with a burn have increased admissions for fractures after discharge. A population-based longitudinal study using linked hospital morbidity and death data from Western Australia was undertaken of all persons hospitalised for a first burn (n=30,997) during the period 1980-2012. Australian population-based annual rates for fracture admissions for the period 1993-2012 were obtained from the Australian Institute of Health and Welfare. Rates of hospital admissions for fractures in the burn cohort and the Australian population were standardised, using the direct method, to the age and gender structure of the Western Australian population at the 2006. Annual standardised fracture admission rates for the period 1993-2012 were graphed with estimated 95% confidence intervals. Age and gender specific fracture rates were also examined. A total of 4004 members of the burn cohort had at least one fracture admission for a total of 6096. The median (IQR) time to the first fracture admission after burn was 6.9 years (2.8-13.6) and the median age (IQR) at first fracture admission was 31 years (20-49). The burn cohort experienced admissions for fractures at a rate approximately twice that of the Australian population. While rates were generally higher for males in the burn cohort when compared with males in the Australian population, female burn patients had significantly higher rates over the entire study period when compared with the female Australian population. Elevated rates were observed for those younger than 20 years at the time of the burn admission; however, rates were significantly and consistently elevated during the study period for those 20 years and older at the time of the burn. Burn patients experienced significantly higher age and gender standardised rates of admissions for fractures after discharge from hospital for their index burn. Further prospective research is indicated to clarify any underlyling pathogenic processes linked to the burn that may increase a patient's risk of having a fracture serious enough to undergo admission. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Thermal characteristics of amphibian microhabitats in a fire-disturbed landscape

USGS Publications Warehouse

Hossack, B.R.; Eby, L.A.; Guscio, C.G.; Corn, P.S.

2009-01-01

Disturbance has long been a central issue in amphibian conservation, often regarding negative effects of logging or other forest management activities, but some amphibians seem to prefer disturbed habitats. After documenting increased use of recently burned forests by boreal toads (Bufo boreas), we hypothesized that burned habitats provided improved thermal opportunities in terrestrial habitats. We tested this hypothesis by conducting a radio telemetry study of habitat use (reported previously) and by using physical models that simulated the temperature of adult toads. We deployed 108 physical models in and adjacent to a 1-year old burn using a fully-replicated design with three burn severities (unburned, partial, high severity) and four microhabitats (open surface, under vegetation, under log, in burrow). Model temperatures were compared to a range of preferred temperatures in published studies. We found 70% more observations within the preferred temperature range of B. boreas in forests burned with high severity than in unburned areas. Burned forest was warmer than unburned forest across all microhabitats, but the largest relative difference was in burrows, which averaged 3 ??C warmer in high-severity burn areas and remained warmer though the night. More than twice as many observations were within the preferred temperature range in high-severity burrows than in unburned burrows. Areas burned with high severity were still warmer than unburned forest 3 years after the fire. Habitat use of toads during the concurrent radio telemetry study matched that predicted by the physical models. These results suggest there are fitness-linked benefits to toads using burned habitats, such as increased growth, fertility, and possibly disease resistance. However, increased soil temperatures that result from wildfire may be detrimental to other amphibian species that prefer cooler temperatures and stable environments. More broadly, our data illustrate the use of physical models to measure and interpret changes that amphibians may experience from disturbance, and highlight the need for research linking vital rates such as growth and survival to disturbance.

Measuring short-term post-fire forest recovery across a burn severity gradient in a mixed pine-oak forest using multi-sensor remote sensing techniques

DOE PAGES

Meng, Ran; Wu, Jin; Zhao, Feng; ...

2018-06-01

Understanding post-fire forest recovery is pivotal to the study of forest dynamics and global carbon cycle. Field-based studies indicated a convex response of forest recovery rate to burn severity at the individual tree level, related with fire-induced tree mortality; however, these findings were constrained in spatial/temporal extents, while not detectable by traditional optical remote sensing studies, largely attributing to the contaminated effect from understory recovery. For this work, we examined whether the combined use of multi-sensor remote sensing techniques (i.e., 1m simultaneous airborne imaging spectroscopy and LiDAR and 2m satellite multi-spectral imagery) to separate canopy recovery from understory recovery wouldmore » enable to quantify post-fire forest recovery rate spanning a large gradient in burn severity over large-scales. Our study was conducted in a mixed pine-oak forest in Long Island, NY, three years after a top-killing fire. Our studies remotely detected an initial increase and then decline of forest recovery rate to burn severity across the burned area, with a maximum canopy area-based recovery rate of 10% per year at moderate forest burn severity class. More intriguingly, such remotely detected convex relationships also held at species level, with pine trees being more resilient to high burn severity and having a higher maximum recovery rate (12% per year) than oak trees (4% per year). These results are one of the first quantitative evidences showing the effects of fire adaptive strategies on post-fire forest recovery, derived from relatively large spatial-temporal domains. Our study thus provides the methodological advance to link multi-sensor remote sensing techniques to monitor forest dynamics in a spatially explicit manner over large-scales, with important implications for fire-related forest management, and for constraining/benchmarking fire effect schemes in ecological process models.« less

Measuring short-term post-fire forest recovery across a burn severity gradient in a mixed pine-oak forest using multi-sensor remote sensing techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Ran; Wu, Jin; Zhao, Feng

Understanding post-fire forest recovery is pivotal to the study of forest dynamics and global carbon cycle. Field-based studies indicated a convex response of forest recovery rate to burn severity at the individual tree level, related with fire-induced tree mortality; however, these findings were constrained in spatial/temporal extents, while not detectable by traditional optical remote sensing studies, largely attributing to the contaminated effect from understory recovery. For this work, we examined whether the combined use of multi-sensor remote sensing techniques (i.e., 1m simultaneous airborne imaging spectroscopy and LiDAR and 2m satellite multi-spectral imagery) to separate canopy recovery from understory recovery wouldmore » enable to quantify post-fire forest recovery rate spanning a large gradient in burn severity over large-scales. Our study was conducted in a mixed pine-oak forest in Long Island, NY, three years after a top-killing fire. Our studies remotely detected an initial increase and then decline of forest recovery rate to burn severity across the burned area, with a maximum canopy area-based recovery rate of 10% per year at moderate forest burn severity class. More intriguingly, such remotely detected convex relationships also held at species level, with pine trees being more resilient to high burn severity and having a higher maximum recovery rate (12% per year) than oak trees (4% per year). These results are one of the first quantitative evidences showing the effects of fire adaptive strategies on post-fire forest recovery, derived from relatively large spatial-temporal domains. Our study thus provides the methodological advance to link multi-sensor remote sensing techniques to monitor forest dynamics in a spatially explicit manner over large-scales, with important implications for fire-related forest management, and for constraining/benchmarking fire effect schemes in ecological process models.« less

Miniature Rocket Motor for Aircraft Stall/Spin Recovery

NASA Technical Reports Server (NTRS)

Lucy, M. H.

1985-01-01

Design accommodates different thrust levels and burn times with minimum weight. Different thrust levels achieved by substituting other propellants of different diameter and burn-rate characteristics. Different burn times achieved by simply changing length of grain/tube assembly. Grain bond material also acts as insulator for fiberglass tube. Rocket motor attached to aircraft model and ignited from radio-controlled 4.8-volt power source. Device provides more than twice energy available in previous designs at only 60 percent of weight. Rocket motor used to identify energy requirements for aircraft stall/spin recovery positive propulsion system.

Results of Propellant Mixing Variable Study Using Precise Pressure-Based Burn Rate Calculations

NASA Technical Reports Server (NTRS)

Stefanski, Philip L.

2014-01-01

A designed experiment was conducted in which three mix processing variables (pre-curative addition mix temperature, pre-curative addition mixing time, and mixer speed) were varied to estimate their effects on within-mix propellant burn rate variability. The chosen discriminator for the experiment was the 2-inch diameter by 4-inch long (2x4) Center-Perforated (CP) ballistic evaluation motor. Motor nozzle throat diameters were sized to produce a common targeted chamber pressure. Initial data analysis did not show a statistically significant effect. Because propellant burn rate must be directly related to chamber pressure, a method was developed that showed statistically significant effects on chamber pressure (either maximum or average) by adjustments to the process settings. Burn rates were calculated from chamber pressures and these were then normalized to a common pressure for comparative purposes. The pressure-based method of burn rate determination showed significant reduction in error when compared to results obtained from the Brooks' modification of the propellant web-bisector burn rate determination method. Analysis of effects using burn rates calculated by the pressure-based method showed a significant correlation of within-mix burn rate dispersion to mixing duration and the quadratic of mixing duration. The findings were confirmed in a series of mixes that examined the effects of mixing time on burn rate variation, which yielded the same results.

The Bee Fire: a case study validation of BEHAVE in chaparral fuels

Treesearch

David Weise; A. Gelobter; J. Regelbrugge; J. Millar

2002-01-01

The Bee Fire burned 9,620 acres of grass and chaparral in the San Bernardino National Forest in southern California from June 29 to July 2, 1996. Rate of spread data were determined from successive fire perimeters and compared with rate of spread predicted by the Rothermel rate of spread model using fuel model 4 (heavy brush) and a custom fuel model for chamise...

In Situ Burning of Oil Spills

PubMed Central

Evans, David D.; Mulholland, George W.; Baum, Howard R.; Walton, William D.; McGrattan, Kevin B.

2001-01-01

For more than a decade NIST conducted research to understand, measure and predict the important features of burning oil on water. Results of that research have been included in nationally recognized guidelines for approval of intentional burning. NIST measurements and predictions have played a major role in establishing in situ burning as a primary oil spill response method. Data are given for pool fire burning rates, smoke yield, smoke particulate size distribution, smoke aging, and polycyclic aromatic hydrocarbon content of the smoke for crude and fuel oil fires with effective diameters up to 17.2 m. New user-friendly software, ALOFT, was developed to quantify the large-scale features and trajectory of wind blown smoke plumes in the atmosphere and estimate the ground level smoke particulate concentrations. Predictions using the model were tested successfully against data from large-scale tests. ALOFT software is being used by oil spill response teams to help assess the potential impact of intentional burning. PMID:27500022

Mesoscale Modeling of Smoke Particles Distribution and Their Radiative Feedback over Northern Sub-Saharan African Region

NASA Astrophysics Data System (ADS)

Yue, Y.; Wang, J.; Ichoku, C. M.; Ellison, L.

2015-12-01

Stretching from southern boundary of Sahara to the equator and expanding west to east from Atlantic Ocean coasts to the India Ocean coasts, the northern sub-Saharan African (NSSA) region has been subject to intense biomass burning. Comprised of savanna, shrub, tropical forest and a number of agricultural crops, the extensive fires burn belt covers central and south of NSSA during dry season (from October to March) contributes to one of the highest biomass burning rate per km2 in the world. Due to smoke particles' absorption effects of solar radiation, they can modify the surface and atmosphere temperature and thus change atmospheric stability, height of the boundary layer, regional atmospheric circulation, evaporation rate, cloud formation, and precipitation. Hence, smoke particles emitted from biomass burning over NSSA region has a significant influence to the air quality, weather and climate variability. In this study, the first version of this Fire Energetics and Emissions Research (FEER.v1) emissions of several smoke constituents including light-absorbing organic carbon (OC) and black carbon (BC) are applied to a state-of-science meteorology-chemistry model as NOAA Weather Research and Forecasting Model with Chemistry (WRF-Chem). We analyzed WRF-Chem simulations of surface and vertical distribution of various pollutants and their direct radiative effects in conjunction with satellite observation data from Moderate Resolution Imaging Spectroradiometer (MODIS) and Cloud-Aerosol Lidar data with Orthogonal Polarization (CALIPSO) to strengthen the importance of combining space measured emission products like FEER.v1 emission inventory with mesoscale model over intense biomass burning region, especially in area where ground-based air-quality and radiation-related observations are limited or absent.

3D rocket combustor acoustics model

NASA Technical Reports Server (NTRS)

Priem, Richard J.; Breisacher, Kevin J.

1992-01-01

The theory and procedures for determining the characteristics of pressure oscillations in rocket engines with prescribed burning rate oscillations are presented. Analyses including radial and hub baffles and absorbers can be performed in one, two, or three dimensions. Pressure and velocity oscillations calculated using this procedure are presented for the SSME to show the influence of baffles and absorbers on the burning rate oscillations required to achieve neutral stability. Comparisons are made between the results obtained utilizing 1D, 2D, and 3D assumption with regards to capturing the physical phenomena of interest and computational requirements.

The Combustion of HMX. [burning rate at high pressures

NASA Technical Reports Server (NTRS)

Boggs, T. L.; Price, C. F.; Atwood, A. I.; Zurn, D. E.; Eisel, J. L.

1980-01-01

The burn rate of HMX was measured at high pressures (p more than 1000 psi). The self deflagration rate of HMX was determined from 1 atmosphere to 50,000 psi. The burning rate shows no significant slope breaks.

Geographic distribution of burn in an Australian setting.

PubMed

Randall, Sean M; Wood, Fiona M; Boyd, James H; Duke, Janine M

2017-11-01

To investigate the geographic distribution and temporal trends of burn admissions in an Australian setting. Health administrative data of all persons hospitalised for a first burn in Western Australia for the period 2000-2012 were used. Crude and standardised incident rates were generated for each region. Maps of crude rates were generated for state regions and postcode-suburbs of Perth, the capital city. Standardised incidence rates were generated for Western Australia, total and regions, and for sub-cohorts defined by age (<20years; ≥20 years), TBSA burn severity and major causes of burns (fire, scalds and contact). Negative binomial regression was used to examine temporal changes and generate incidence rate ratios (IRR) with 95% confidence intervals (CI). Perth had the lowest burn admission rate per population; clusters of suburbs of lower social advantage and higher immigrant settlement were identified as being at high risk. While the highest observed admission rates were found in Kimberley and Goldfields (remote) regions, after adjustment for the regional demographic structures, the Wheatbelt and Mid-West (rural) regions were found to have the highest adjusted rates of burn admissions. Significant annual declines in admission rates were found for the Kimberley, Pilbara and Goldfields (remote regions); however, stable admission rates were identified for all other regions. The Mid-West and Wheatbelt rural regions were found to have the highest risk of burn admissions raising concerns about farming-related injury. Safety awareness and burn prevention strategies need to be continued, with specific attention to these high risk areas, to reduce burn admissions in Western Australia. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

CFD analysis of gas explosions vented through relief pipes.

PubMed

Ferrara, G; Di Benedetto, A; Salzano, E; Russo, G

2006-09-21

Vent devices for gas and dust explosions are often ducted to safe locations by means of relief pipes. However, the presence of the duct increases the severity of explosion if compared to simply vented vessels (i.e. compared to cases where no duct is present). Besides, the identification of the key phenomena controlling the violence of explosion has not yet been gained. Multidimensional models coupling, mass, momentum and energy conservation equations can be valuable tools for the analysis of such complex explosion phenomena. In this work, gas explosions vented through ducts have been modelled by a two-dimensional (2D) axi-symmetric computational fluid dynamic (CFD) model based on the unsteady Reynolds Averaged Navier Stokes (RANS) approach in which the laminar, flamelet and distributed combustion models have been implemented. Numerical test have been carried out by varying ignition position, duct diameter and length. Results have evidenced that the severity of ducted explosions is mainly driven by the vigorous secondary explosion occurring in the duct (burn-up) rather than by the duct flow resistance or acoustic enhancement. Moreover, it has been found out that the burn-up affects explosion severity due to the reduction of venting rate rather than to the burning rate enhancement through turbulization.

Natural gas availability and ambient air quality in the Baton Rouge/New Orleans industrial complex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fieler, E.R.; Harrison, D.P.

1978-02-26

Three scenarios were modeled for the Baton Rouge/New Orleans area for 1985: one assumes the substitution of residual oil (0.7% sulfur) for gas to decrease gas-burning stationary sources from 80 to 8% and the use of properly designed stacks for large emitters; the second makes identical gas supply assumptions but adds proper stack dispersion for medium as well as large emitters; and the third is based on 16% gas-burning stationary sources. The Climatological Dispersion Model was used to translate (1974) emission rates into ambient air concentrations. Growth rates for residential, commercial, and transportation sources, but not industry, were considered. Themore » results show that proper policies, which would require not only tall stacks for large oil burning units (and for intermediate units also in the areas of high industrial concentration), but also the careful location of new plants would permit continued industrial expansion without severe air pollution problems.« less

3D hydrodynamic simulations of carbon burning in massive stars

NASA Astrophysics Data System (ADS)

Cristini, A.; Meakin, C.; Hirschi, R.; Arnett, D.; Georgy, C.; Viallet, M.; Walkington, I.

2017-10-01

We present the first detailed 3D hydrodynamic implicit large eddy simulations of turbulent convection of carbon burning in massive stars. Simulations begin with radial profiles mapped from a carbon-burning shell within a 15 M⊙ 1D stellar evolution model. We consider models with 1283, 2563, 5123, and 10243 zones. The turbulent flow properties of these carbon-burning simulations are very similar to the oxygen-burning case. We performed a mean field analysis of the kinetic energy budgets within the Reynolds-averaged Navier-Stokes framework. For the upper convective boundary region, we find that the numerical dissipation is insensitive to resolution for linear mesh resolutions above 512 grid points. For the stiffer, more stratified lower boundary, our highest resolution model still shows signs of decreasing sub-grid dissipation suggesting it is not yet numerically converged. We find that the widths of the upper and lower boundaries are roughly 30 per cent and 10 per cent of the local pressure scaleheights, respectively. The shape of the boundaries is significantly different from those used in stellar evolution models. As in past oxygen-shell-burning simulations, we observe entrainment at both boundaries in our carbon-shell-burning simulations. In the large Péclet number regime found in the advanced phases, the entrainment rate is roughly inversely proportional to the bulk Richardson number, RiB (∝RiB-α, 0.5 ≲ α ≲ 1.0). We thus suggest the use of RiB as a means to take into account the results of 3D hydrodynamics simulations in new 1D prescriptions of convective boundary mixing.

Development of strand burner for solid propellant burning rate studies

NASA Astrophysics Data System (ADS)

Aziz, A.; Mamat, R.; Ali, W. K. Wan

2013-12-01

It is well-known that a strand burner is an apparatus that provides burning rate measurements of a solid propellant at an elevated pressure in order to obtain the burning characteristics of a propellant. This paper describes the facilities developed by author that was used in his studies. The burning rate characteristics of solid propellant have be evaluated over five different chamber pressures ranging from 1 atm to 31 atm using a strand burner. The strand burner has a mounting stand that allows the propellant strand to be mounted vertically. The strand was ignited electrically using hot wire, and the burning time was recorded by electronic timer. Wire technique was used to measure the burning rate. Preliminary results from these techniques are presented. This study shows that the strand burner can be used on propellant strands to obtain accurate low pressure burning rate data.

Erosive burning research. [for solid-propellant rocket engines

NASA Technical Reports Server (NTRS)

Strand, L.; Yang, L. C.; Nguyen, M. H.; Cohen, N. S.

1986-01-01

A status report is given on the results for the completed tests in a series of motor firings being carried out to measure the effects of the parameters that are considered to most strongly influence the scaling to larger rocket motor sizes of the transition to/or threshold conditions for erosive burning rate augmentation. Propellant burning rates at locations along the axis of the test motors are measured with a newly developed plasma capacitance gauge technique. The measured results are compared with erosive-burning predictions from a supporting ballistics analysis. The completed motor firings have successfully demonstrated response to the designed test variables. The trends with varying propellant burning rate, chamber pressure, and mass flow rate are consistent with existing results, but no pronounced effect of surface roughness has been observed. Rather, the influence of propellant oxidizer particle size on erosive burning is through its effect on the base, no-corssflow burning rate.

Biomass Combustions and Burning Emissions Inferred from GOES Fire Radiative Power

NASA Astrophysics Data System (ADS)

Zhang, X.; Kondragunta, S.; Schmidt, C.

2007-12-01

Biomass burning significantly affects air quality and climate changes. Current estimates of burning emissions are rather imprecise and vary markedly with different methodologies. This paper investigates biomass burning consumption and emissions using GOES (Geostationary Operational Environmental Satellites) WF_ABBA (Wildfire Automated Biomass Burning Algorithm) fire product. In doing this, we establish a set of representatives in diurnal patterns of half-hourly GOES Fire Radiative Power (FRP) for various ecosystems. The representative patterns are used to fill the missed and poor observations of half hourly FRP in GOES fire data for individual fire pixels. The simulated FRP is directly applied to the calculation of the biomass combusted during fire activities. The FRP-based biomass combustion is evaluated using the estimates using a traditional model which integrates burned area, fuel loading, and combustion factor. In the traditional model calculation, we derive burned areas from GOES WF_ABBA fire size. Fuel loading includes three different types (1) MODIS Vegetation Property-based Fuel System (MVPFS), (2) National Dangerous Rating Systems (NFDRS), and (3) the Fuel Characteristic Classification System (FCCS). By comparing the biomass combustions across the Contiguous United States (CONUS) from 2003-2005, we conclude that FRP is an effective tool to estimate the biomass burning emissions. Finally, we examine the temporal and spatial patterns in biomass combustions and emissions (PM2.5, CO, NH3) across the CONUS.

Ozone budget over the Amazon - Regional effects from biomass-burning emissions

NASA Technical Reports Server (NTRS)

Richardson, Jennifer L.; Fishman, Jack; Gregory, Gerald L.

1991-01-01

Data from the NASA dry-season Amazon boundary layer experiment (ABLE2A) is used with a 1D tropospheric photochemical model to analyze the atmospheric chemistry in the region and determine the impact of the long-range transport of biomass-burning emissions. Inputs of surface sources and the deposition of various species measured during ABLE2A are employed to simulate the background atmosphere, and haze characteristics are introduced for a 12-hr simulation. The in situ ozone production rate doubles during the period of haze when hydrocarbons are present. The model predicts that the production of ozone is enhanced during the dry season, and that increased ozone during the southern tropical burning season is related to the regional transport of haze.

The impact of biogenic, anthropogenic, and biomass burning volatile organic compound emissions on regional and seasonal variations in secondary organic aerosol

NASA Astrophysics Data System (ADS)

Kelly, Jamie M.; Doherty, Ruth M.; O'Connor, Fiona M.; Mann, Graham W.

2018-05-01

The global secondary organic aerosol (SOA) budget is highly uncertain, with global annual SOA production rates, estimated from global models, ranging over an order of magnitude and simulated SOA concentrations underestimated compared to observations. In this study, we use a global composition-climate model (UKCA) with interactive chemistry and aerosol microphysics to provide an in-depth analysis of the impact of each VOC source on the global SOA budget and its seasonality. We further quantify the role of each source on SOA spatial distributions, and evaluate simulated seasonal SOA concentrations against a comprehensive set of observations. The annual global SOA production rates from monoterpene, isoprene, biomass burning, and anthropogenic precursor sources is 19.9, 19.6, 9.5, and 24.6 Tg (SOA) a-1, respectively. When all sources are included, the SOA production rate from all sources is 73.6 Tg (SOA) a-1, which lies within the range of estimates from previous modelling studies. SOA production rates and SOA burdens from biogenic and biomass burning SOA sources peak during Northern Hemisphere (NH) summer. In contrast, the anthropogenic SOA production rate is fairly constant all year round. However, the global anthropogenic SOA burden does have a seasonal cycle which is lowest during NH summer, which is probably due to enhanced wet removal. Inclusion of the new SOA sources also accelerates the ageing by condensation of primary organic aerosol (POA), making it more hydrophilic, leading to a reduction in the POA lifetime. With monoterpene as the only source of SOA, simulated SOA and total organic aerosol (OA) concentrations are underestimated by the model when compared to surface and aircraft measurements. Model agreement with observations improves with all new sources added, primarily due to the inclusion of the anthropogenic source of SOA, although a negative bias remains. A further sensitivity simulation was performed with an increased anthropogenic SOA reaction yield, corresponding to an annual global SOA production rate of 70.0 Tg (SOA) a-1. Whilst simulated SOA concentrations improved relative to observations, they were still underestimated in urban environments and overestimated further downwind and in remote environments. In contrast, the inclusion of SOA from isoprene and biomass burning did not improve model-observations biases substantially except at one out of two tropical locations. However, these findings may reflect the very limited availability of observations to evaluate the model, which are primarily located in the NH mid-latitudes where anthropogenic emissions are high. Our results highlight that, within the current uncertainty limits in SOA sources and reaction yields, over the NH mid-latitudes, a large anthropogenic SOA source results in good agreement with observations. However, more observations are needed to establish the importance of biomass burning and biogenic sources of SOA in model agreement with observations.

Interactive effects of fire, soil climate, and moss on CO2 fluxes in black spruce ecosystems of interior Alaska

USGS Publications Warehouse

O'Donnell, J. A.; Turetsky, M.R.; Harden, J.W.; Manies, K.L.; Pruett, L.E.; Shetler, G.; Neff, J.C.

2009-01-01

Fire is an important control on the carbon (C) balance of the boreal forest region. Here, we present findings from two complementary studies that examine how fire modifies soil organic matter properties, and how these modifications influence rates of decomposition and C exchange in black spruce (Picea mariana) ecosystems of interior Alaska. First, we used laboratory incubations to explore soil temperature, moisture, and vegetation effects on CO2 and DOC production rates in burned and unburned soils from three study regions in interior Alaska. Second, at one of the study regions used in the incubation experiments, we conducted intensive field measurements of net ecosystem exchange (NEE) and ecosystem respiration (ER) across an unreplicated factorial design of burning (2 year post-fire versus unburned sites) and drainage class (upland forest versus peatland sites). Our laboratory study showed that burning reduced the sensitivity of decomposition to increased temperature, most likely by inducing moisture or substrate quality limitations on decomposition rates. Burning also reduced the decomposability of Sphagnum-derived organic matter, increased the hydrophobicity of feather moss-derived organic matter, and increased the ratio of dissolved organic carbon (DOC) to total dissolved nitrogen (TDN) in both the upland and peatland sites. At the ecosystem scale, our field measurements indicate that the surface organic soil was generally wetter in burned than in unburned sites, whereas soil temperature was not different between the burned and unburned sites. Analysis of variance results showed that ER varied with soil drainage class but not by burn status, averaging 0.9 ?? 0.1 and 1.4 ?? 0.1 g C m-2d-1 in the upland and peatland sites, respectively. However, a more complex general linear model showed that ER was controlled by an interaction between soil temperature, moisture, and burn status, and in general was less variable over time in the burned than in the unburned sites. Together, findings from these studies across different spatial scales suggest that although fire can create some soil climate conditions more conducive to rapid decomposition, rates of C release from soils may be constrained following fire by changes in moisture and/or substrate quality that impede rates of decomposition. ?? 2008 Springer Science+Business Media, LLC.

Interactive effects of fire, soil climate, and moss on CO2 fluxes in black spruce ecosystems of interior Alaska

USGS Publications Warehouse

O'Donnell, Jonathan A.; Turetsky, Merritt R.; Harden, Jennifer W.; Manies, Kristen L.; Pruett, L.E.; Shetler, Gordon; Neff, Jason C.

2009-01-01

Fire is an important control on the carbon (C) balance of the boreal forest region. Here, we present findings from two complementary studies that examine how fire modifies soil organic matter properties, and how these modifications influence rates of decomposition and C exchange in black spruce (Picea mariana) ecosystems of interior Alaska. First, we used laboratory incubations to explore soil temperature, moisture, and vegetation effects on CO2 and DOC production rates in burned and unburned soils from three study regions in interior Alaska. Second, at one of the study regions used in the incubation experiments, we conducted intensive field measurements of net ecosystem exchange (NEE) and ecosystem respiration (ER) across an unreplicated factorial design of burning (2 year post-fire versus unburned sites) and drainage class (upland forest versus peatland sites). Our laboratory study showed that burning reduced the sensitivity of decomposition to increased temperature, most likely by inducing moisture or substrate quality limitations on decomposition rates. Burning also reduced the decomposability of Sphagnum-derived organic matter, increased the hydrophobicity of feather moss-derived organic matter, and increased the ratio of dissolved organic carbon (DOC) to total dissolved nitrogen (TDN) in both the upland and peatland sites. At the ecosystem scale, our field measurements indicate that the surface organic soil was generally wetter in burned than in unburned sites, whereas soil temperature was not different between the burned and unburned sites. Analysis of variance results showed that ER varied with soil drainage class but not by burn status, averaging 0.9 ± 0.1 and 1.4 ± 0.1 g C m−2 d−1 in the upland and peatland sites, respectively. However, a more complex general linear model showed that ER was controlled by an interaction between soil temperature, moisture, and burn status, and in general was less variable over time in the burned than in the unburned sites. Together, findings from these studies across different spatial scales suggest that although fire can create some soil climate conditions more conducive to rapid decomposition, rates of C release from soils may be constrained following fire by changes in moisture and/or substrate quality that impede rates of decomposition.

Nitramine smokeless propellant research

NASA Technical Reports Server (NTRS)

Cohen, N. S.; Strand, L. P.

1977-01-01

A transient ballistics and combustion model is derived to represent the closed vessel experiment that is widely used to characterize propellants. A computer program is developed to solve the time-dependent equations, and is applied to explain aspects of closed vessel behavior. In the case of nitramine propellants the cratering of the burning surface associated with combustion above break-point pressures augments the effective burning rate as deduced from the closed vessel experiment. Low pressure combustion is significantly affected by the ignition process and, in the case of nitramine propellants, by the developing and changing surface structure. Thus, burning rates deduced from the closed vessel experiment may or may not agree with those measured in the equilibrium strand burner. Series of T burner experiments are performed to compare the combustion instability characteristics of nitramine (HMX) containing propellants and ammonium perchlorate (AP)propellants. Although ash produced by more fuel rich propellants could have provided mechanical suppression, results from clean-burning propellants permit the conclusion that HMX reduces the acoustic driving.

Burns and Fire Safety

MedlinePlus

Number of Deaths Death Rate Burns and Fire Safety Fact Sheet (2015) Fatalities • 334 children ages 19 and under died from fires or burns ... burns were ages 4 and under. 1 The death rate for children this age (0.73 per 100, ...

Burns and long-term infectious disease morbidity: A population-based study.

PubMed

Duke, Janine M; Randall, Sean M; Wood, Fiona M; Boyd, James H; Fear, Mark W

2017-03-01

There is a growing volume of data that indicates that serious injury suppresses immune function, predisposing individuals to infectious complications. With recent evidence showing long-term immune dysfunction after less severe burn, this study aimed to investigate post-burn infectious disease morbidity and assess if burn patients have increased long-term hospital use for infectious diseases. A population-based longitudinal study using linked hospital morbidity and death data from Western Australia for all persons hospitalised for a first burn (n=30,997) in 1980-2012. A frequency matched non-injury comparison cohort was randomly selected from Western Australia's birth registrations and electoral roll (n=123,399). Direct standardisation was used to assess temporal trends in infectious disease admissions. Crude annual admission rates and length of stay for infectious diseases were calculated. Multivariate negative binomial and Cox proportional hazards regression modeling were used to generate adjusted incidence rate ratios (IRR) and hazard ratios (HR), respectively. After adjustment for demographic factors and pre-existing health status, the burn cohort had twice (IRR, 95% confidence interval (CI): 2.04, 1.98-2.22) as many admissions and 3.5 times the number of days in hospital (IRR, 95%CI: 3.46, 3.05-3.92) than the uninjured cohort for infectious diseases. Higher rates of infectious disease admissions were found for severe (IRR, 95%CI: 2.37, 1.89-2.97) and minor burns (IRR, 95%CI: 2.22, 2.11-2.33). Burns were associated with significantly increased incident admissions: 0-30days (HR, 95%CI: 5.18, 4.15-6.48); 30days-1year (HR, 95%CI: 1.69, 1.53-1.87); 1-10 years (HR, 95%CI: 1.40:1.33-1.47); >10years (HR, 95%CI: 1.16, 1.08-1.24). Respiratory, skin and soft tissue and gastrointestinal infections were the most common. The burn cohort had a 1.75 (95%CI: 1.37-2.25) times greater rate of mortality caused by infectious diseases during the 5-year period after discharge than the uninjured cohort. These findings suggest that burn has long-lasting effects on the immune system and its function. The increase in infectious disease in three different epithelial tissues in the burn cohort suggests there may be common underlying pathophysiology. Further research to understand the underlying mechanisms are required to inform clinical interventions to mitigate infectious disease after burn and improve patient outcomes. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Bridging burn care education with modern technology, an integration with high fidelity human patient simulation.

PubMed

Reeves, Patrick T; Borgman, Matthew A; Caldwell, Nicole W; Patel, Leela; Aden, James; Duggan, John P; Serio-Melvin, Maria L; Mann-Salinas, Elizabeth A

2018-08-01

The Advanced Burn Life Support (ABLS) program is a burn-education curriculum nearly 30 years in the making, focusing on the unique challenges of the first 24h of care after burn injury. Our team applied high fidelity human patient simulation (HFHPS) to the established ABLS curriculum. Our hypothesis was that HFHPS would be a feasible, easily replicable, and valuable adjunct to the current curriculum that would enhance learner experience. This prospective, evidenced-based practice project was conducted in a single simulation center employing the American Burn Association's ABLS curriculum using HFHPS. Participants managed 7 separate simulated polytrauma and burn scenarios with resultant clinical complications. After training, participants completed written and practical examinations as well as satisfaction surveys. From 2012 to 2013, 71 students participated in this training. Simulation (ABLS-Sim) participants demonstrated a 2.5% increase in written post-test scores compared to traditional ABLS Provider Course (ABLS Live) (p=0.0016). There was no difference in the practical examination when comparing ABLS-Sim versus ABLS Live. Subjectively, 60 (85%) participants completed surveys. The Educational Practice Questionnaire showed best practices rating of 4.5±0.7; with importance of learning rated at 4.4±0.8. The Simulation Design Scale rating for design was 4.6±0.6 with an importance rating of 4.4±0.8. Overall Satisfaction and Self-Confidence with Learning were 4.4±0.7 and 4.5±0.7, respectfully. Integrating HFHPS with the current ABLS curriculum led to higher written exam scores, high levels of confidence, satisfaction, and active learning, and presented an evidenced-based model for education that is easily employable for other facilities nationwide. Copyright © 2018 Elsevier Ltd and ISBI. All rights reserved.

Nonlinear Burn Control in Tokamaks using Heating, Non-axisymmetric Magnetic Fields, Isotopic fueling and Impurity injection

NASA Astrophysics Data System (ADS)

Pajares, Andres; Schuster, Eugenio

2016-10-01

Plasma density and temperature regulation in future tokamaks such as ITER is arising as one of the main problems in nuclear-fusion control research. The problem, known as burn control, is to regulate the amount of fusion power produced by the burning plasma while avoiding thermal instabilities. Prior work in the area of burn control considered different actuators, such as modulation of the auxiliary power, modulation of the fueling rate, and controlled impurity injection. More recently, the in-vessel coil system was suggested as a feasible actuator since it has the capability of modifying the plasma confinement by generating non-axisymmetric magnetic fields. In this work, a comprehensive, model-based, nonlinear burn control strategy is proposed to integrate all the previously mentioned actuators. A model to take into account the influence of the in-vessel coils on the plasma confinement is proposed based on the plasma collisionality and the density. A simulation study is carried out to show the capability of the controller to drive the system between different operating points while rejecting perturbations. Supported by the US DOE under DE-SC0010661.

Brown adipose tissue and its modulation by a mitochondria-targeted peptide in rat burn injury-induced hypermetabolism

PubMed Central

Yo, Kikuo; Yu, Yong-Ming; Zhao, Gaofeng; Bonab, Ali A.; Aikawa, Naoki; Tompkins, Ronald G.

2013-01-01

Hypermetabolism is a prominent feature of burn injury, and altered mitochondria function is presumed to contribute to this state. Recently, brown adipose tissue (BAT) was found to be present not only in rodents but also in humans, and its activity is associated with resting metabolic rate. In this report, we elucidate the relationship between burn injury-induced hypermetabolism and BAT activity and the possible role of the mitochondria-targeted peptide SS31 in attenuating burn injury-induced hypermetabolism by using a rat burn injury model. We demonstrate that burn injury induces morphological changes in interscapular BAT (iBAT). Burn injury was associated with iBAT activation, and this effect was positively correlated with increased energy expenditure. BAT activation was associated with augmentation of mitochondria biogenesis, and UCP1 expression in the isolated iBAT mitochondria. In addition, the mitochondria-targeted peptide SS31 attenuated burn injury-induced hypermetabolism, which was accompanied by suppression of UCP1 expression in isolated mitochondria. Our results suggest that BAT plays an important role in burn injury-induced hypermetabolism through its morphological changes and expression of UCP1. PMID:23169784

Brown adipose tissue and its modulation by a mitochondria-targeted peptide in rat burn injury-induced hypermetabolism.

PubMed

Yo, Kikuo; Yu, Yong-Ming; Zhao, Gaofeng; Bonab, Ali A; Aikawa, Naoki; Tompkins, Ronald G; Fischman, Alan J

2013-02-15

Hypermetabolism is a prominent feature of burn injury, and altered mitochondria function is presumed to contribute to this state. Recently, brown adipose tissue (BAT) was found to be present not only in rodents but also in humans, and its activity is associated with resting metabolic rate. In this report, we elucidate the relationship between burn injury-induced hypermetabolism and BAT activity and the possible role of the mitochondria-targeted peptide SS31 in attenuating burn injury-induced hypermetabolism by using a rat burn injury model. We demonstrate that burn injury induces morphological changes in interscapular BAT (iBAT). Burn injury was associated with iBAT activation, and this effect was positively correlated with increased energy expenditure. BAT activation was associated with augmentation of mitochondria biogenesis, and UCP1 expression in the isolated iBAT mitochondria. In addition, the mitochondria-targeted peptide SS31 attenuated burn injury-induced hypermetabolism, which was accompanied by suppression of UCP1 expression in isolated mitochondria. Our results suggest that BAT plays an important role in burn injury-induced hypermetabolism through its morphological changes and expression of UCP1.

Improved Survival of Patients With Extensive Burns: Trends in Patient Characteristics and Mortality Among Burn Patients in a Tertiary Care Burn Facility, 2004-2013.

PubMed

Strassle, Paula D; Williams, Felicia N; Napravnik, Sonia; van Duin, David; Weber, David J; Charles, Anthony; Cairns, Bruce A; Jones, Samuel W

Classic determinants of burn mortality are age, burn size, and the presence of inhalation injury. Our objective was to describe temporal trends in patient and burn characteristics, inpatient mortality, and the relationship between these characteristics and inpatient mortality over time. All patients aged 18 years or older and admitted with burn injury, including inhalation injury only, between 2004 and 2013 were included. Adjusted Cox proportional hazards regression models were used to estimate the relationship between admit year and inpatient mortality. A total of 5540 patients were admitted between 2004 and 2013. Significant differences in sex, race/ethnicity, burn mechanisms, TBSA, inhalation injury, and inpatient mortality were observed across calendar years. Patients admitted between 2011 and 2013 were more likely to be women, non-Hispanic Caucasian, with smaller burn size, and less likely to have an inhalation injury, in comparison with patients admitted from 2004 to 2010. After controlling for patient demographics, burn mechanisms, and differential lengths of stay, no calendar year trends in inpatient mortality were detected. However, a significant decrease in inpatient mortality was observed among patients with extensive burns (≥75% TBSA) in more recent calendar years. This large, tertiary care referral burn center has maintained low inpatient mortality rates among burn patients over the past 10 years. While observed decreases in mortality during this time are largely due to changes in patient and burn characteristics, survival among patients with extensive burns has improved.

Single Degenerate Models for Type Ia Supernovae: Progenitor's Evolution and Nucleosynthesis Yields

NASA Astrophysics Data System (ADS)

Nomoto, Ken'ichi; Leung, Shing-Chi

2018-06-01

We review how the single degenerate models for Type Ia supernovae (SNe Ia) works. In the binary star system of a white dwarf (WD) and its non-degenerate companion star, the WD accretes either hydrogen-rich matter or helium and undergoes hydrogen and helium shell-burning. We summarize how the stability and non-linear behavior of such shell-burning depend on the accretion rate and the WD mass and how the WD blows strong wind. We identify the following evolutionary routes for the accreting WD to trigger a thermonuclear explosion. Typically, the accretion rate is quite high in the early stage and gradually decreases as a result of mass transfer. With decreasing rate, the WD evolves as follows: (1) At a rapid accretion phase, the WD increase its mass by stable H burning and blows a strong wind to keep its moderate radius. The wind is strong enough to strip a part of the companion star's envelope to control the accretion rate and forms circumstellar matter (CSM). If the WD explodes within CSM, it is observed as an "SN Ia-CSM". (X-rays emitted by the WD are absorbed by CSM.) (2) If the WD continues to accrete at a lower rate, the wind stops and an SN Ia is triggered under steady-stable H shell-burning, which is observed as a super-soft X-ray source: "SN Ia-SSXS". (3) If the accretion continues at a still lower rate, H shell-burning becomes unstable and many flashes recur. The WD undergoes recurrent nova (RN) whose mass ejection is smaller than the accreted matter. Then the WD evolves to an "SN Ia-RN". (4) If the companion is a He star (or a He WD), the accretion of He can trigger He and C double detonations at the sub-Chandrasekhar mass or the WD grows to the Chandrasekhar mass while producing a He-wind: "SN Ia-He CSM". (5) If the accreting WD rotates quite rapidly, the WD mass can exceed the Chandrasekhar mass of the spherical WD, which delays the trigger of an SN Ia. After angular momentum is lost from the WD, the (super-Chandra) WD contracts to become a delayed SN Ia. The companion star has become a He WD and CSM has disappeared: "SN Ia-He WD". We update nucleosynthesis yields of the carbon deflagration model W7, delayed detonation model WDD2, and the sub-Chandrasekhar mass model to provide some constraints on the yields (such as Mn) from the comparison with the observations. We note the important metallicity effects on 58Ni and 55Mn.

An Experimental Examination of Combustion of Isolated Liquid Fuel Droplets with Polymeric and Nanoparticle Additives

NASA Astrophysics Data System (ADS)

Ghamari, Mohsen

In spite of recent attention to renewable sources of energy, liquid hydrocarbon fuels are still the main source of energy for industrial and transportation systems. Manufactures and consumers are consistently looking for ways to optimize the efficiency of fuel combustion in terms of cost, emissions and consumer safety. In this regard, increasing burning rate of liquid fuels has been of special interest in both industrial and transportation systems. Recent studies have shown that adding combustible nano-particles could have promising effects on improving combustion performance of liquid fuels. Combustible nano-particles could enhance radiative and conductive heat transfer and also mixing within the droplet. Polymeric additive have also shown promising effect on improving fire safety by suppressing spreading behavior and splatter formation in case of crash scenario. Polymers are also known to have higher burning rate than regular hydrocarbon fuels. Therefore adding polymeric additive could have the potential to increase the burning rate. In this work, combustion dynamics of liquid fuel droplets with both polymeric and nanoparticle additives is studied in normal gravity. High speed photography is employed and the effect of additive concentration on droplet burning rate, burning time, extinction and soot morphology is investigated. Polymer added fuel was found to have a volatility controlled combustion with four distinct regimes. The first three zones are associated with combustion of base fuel while the polymer burns last and after a heating zone because of its higher boiling point. Polymer addition reduces the burning rate of the base fuel in the first zone by means of increasing viscosity and results in nucleate boiling and increased burning rates in the second and third stages. Overall, polymer addition resulted in a higher burning rate and shorter burning time in most of the scenarios. Colloidal suspensions of carbon-based nanomaterials in liquid fuels were also tested at different particle loadings. It was found that dispersing nanoparticles results in higher burning rate by means of enhanced radiative heat absorption and thermal conductivity. An optimum particle loading was found for each particle type at which the maximum burning rate was achieved. It was observed that the burning rate again starts to reduce after this optimum point most likely due to the formation of large aggregates that reduce thermal conductivity and suppress the diffusion of species.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menikoff, Ralph

SURFplus is a reactive burn model for high explosives aimed at modelling shock initiation and propagation of detonation waves. It utilizes the SURF model for the fast hot-spot reaction plus a slow reaction for the energy released by carbon clustering. A feature of the SURF model is that there is a partially decoupling between burn rate parameters and detonation wave properties. Previously, parameters for PBX 9502 that control shock ini- tiation had been calibrated to Pop plot data (distance-of-run to detonation as a function of shock pressure initiating the detonation). Here burn rate parameters for the high pres- sure regimemore » are adjusted to t the failure diameter and the limiting detonation speed just above the failure diameter. Simulated results are shown for an uncon ned rate stick when the 9502 diameter is slightly above and slightly below the failure diameter. Just above the failure diameter, in the rest frame of the detonation wave, the front is sonic at the PBX/air interface. As a consequence, the lead shock in the neighborhood of the interface is supported by the detonation pressure in the interior of the explosive rather than the reaction immediately behind the front. In the interior, the sonic point occurs near the end of the fast hot-spot reaction. Consequently, the slow carbon clustering reaction can not a ect the failure diameter. Below the failure diameter, the radial extent of the detonation front decreases starting from the PBX/air interface. That is, the failure starts at the PBX boundary and propagates inward to the axis of the rate stick.« less

Statistical Hotspot Model for Explosive Detonation

NASA Astrophysics Data System (ADS)

Nichols, Albert

2005-07-01

The presence and need for energy localization in the ignition and detonation of high explosives is a corner stone in our understanding of explosive behavior. This energy localization, known as hot spots, provides the match that starts the energetic response that is integral to the detonation. In our model, we use the life cycle of a hot spot to predict explosive response. This life cycle begins with a random distribution of inhomogeneities in the explosive that we describe as a potential hot spot. A shock wave can transform these into hot spots that can then grow by consuming the explosive around them. The fact that the shock wave can collapse a potential hot spot without causing ignition is required in order to model phenomena like dead pressing. The burn rate of the hot spot is taken directly from experimental data. In our approach we do not assume that every hot spot is burning in an identical environment, but rather we take a statistical approach to the burning process. We also do not make a uniform temperature assumption in order to close the mixture equation of state, but track the flow of energy from reactant to product. Finally, we include both the hot spot burn model and a thermal decomposition path, required to explain certain long time behaviors. Building on work performed by Reaugh et. al., we have developed a set of reaction parameters for an HMX based heterogeneous explosive. These parameters have been determined from computer models on the micron scale, and experimental data. This model will be compared to experimental rate stick data. This work was performed under the auspices of the U.S. Department of Energy by University of California, Lawrence Livermore National Laboratory under Contract W-7405-Eng-48.

Experimental and modeling studies of small molecule chemistry in expanding spherical flames

NASA Astrophysics Data System (ADS)

Santner, Jeffrey

Accurate models of flame chemistry are required in order to predict emissions and flame properties, such that clean, efficient engines can be designed more easily. There are three primary methods used to improve such combustion chemistry models - theoretical reaction rate calculations, elementary reaction rate experiments, and combustion system experiments. This work contributes to model improvement through the third method - measurements and analysis of the laminar burning velocity at constraining conditions. Modern combustion systems operate at high pressure with strong exhaust gas dilution in order to improve efficiency and reduce emissions. Additionally, flames under these conditions are sensitized to elementary reaction rates such that measurements constrain modeling efforts. Measurement conditions of the present work operate within this intersection between applications and fundamental science. Experiments utilize a new pressure-release, heated spherical combustion chamber with a variety of fuels (high hydrogen content fuels, formaldehyde (via 1,3,5-trioxane), and C2 fuels) at pressures from 0.5--25 atm, often with dilution by water vapor or carbon dioxide to flame temperatures below 2000 K. The constraining ability of these measurements depends on their uncertainty. Thus, the present work includes a novel analytical estimate of the effects of thermal radiative heat loss on burning velocity measurements in spherical flames. For 1,3,5-trioxane experiments, global measurements are sufficiently sensitive to elementary reaction rates that optimization techniques are employed to indirectly measure the reaction rates of HCO consumption. Besides the influence of flame chemistry on propagation, this work also explores the chemistry involved in production of nitric oxide, a harmful pollutant, within flames. We find significant differences among available chemistry models, both in mechanistic structure and quantitative reaction rates. There is a lack of well-defined measurements of nitric oxide formation at high temperatures, contributing to disagreement between chemical models. This work accomplishes several goals. It identifies disagreements in pollutant formation chemistry. It creates a novel database of burning velocity measurements at relevant, sensitive conditions. It presents a simple, conservative estimate of radiation-induced measurement uncertainty in spherical flames. Finally, it utilizes systems-level flame experiments to indirectly measure elementary reaction rates.

Study of the ion kinetic effects in ICF run-away burn using a quasi-1D hybrid model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Cheng -Kun; Molvig, Kim; Albright, Brian James

Here, the loss of fuel ions in the Gamow peak and other kinetic effects related to the α particles during ignition, run-away burn, and disassembly stages of an inertial confinement fusion D-T capsule are investigated with a quasi-1D hybrid volume ignition model that includes kinetic ions, fluid electrons, Planckian radiation photons, and a metallic pusher. The fuel ion loss due to the Knudsen effect at the fuel-pusher interface is accounted for by a local-loss model by with an albedo model for ions returning from the pusher wall. The tail refilling and relaxation of the fuel ion distribution are captured withmore » a nonlinear Fokker-Planck solver. Alpha heating of the fuel ions is modeled kinetically while simple models for finite alpha range and electron heating are used. This dynamical model is benchmarked with a 3 T hydrodynamic burn model employing similar assumptions. For an energetic pusher (~40 kJ) that compresses the fuel to an areal density of ~1.07g/cm 2 at ignition, the simulation shows that the Knudsen effect can substantially limit ion temperature rise in runaway burn. While the final yield decreases modestly from kinetic effects of the α particles, large reduction of the fuel reactivity during ignition and runaway burn may require a higher Knudsen loss rate compared to the rise time of the temperatures above ~25 keV when the broad D-T Gamow peak merges into the bulk Maxwellian distribution.« less

Study of the ion kinetic effects in ICF run-away burn using a quasi-1D hybrid model

DOE PAGES

Huang, Cheng -Kun; Molvig, Kim; Albright, Brian James; ...

2017-02-21

Here, the loss of fuel ions in the Gamow peak and other kinetic effects related to the α particles during ignition, run-away burn, and disassembly stages of an inertial confinement fusion D-T capsule are investigated with a quasi-1D hybrid volume ignition model that includes kinetic ions, fluid electrons, Planckian radiation photons, and a metallic pusher. The fuel ion loss due to the Knudsen effect at the fuel-pusher interface is accounted for by a local-loss model by with an albedo model for ions returning from the pusher wall. The tail refilling and relaxation of the fuel ion distribution are captured withmore » a nonlinear Fokker-Planck solver. Alpha heating of the fuel ions is modeled kinetically while simple models for finite alpha range and electron heating are used. This dynamical model is benchmarked with a 3 T hydrodynamic burn model employing similar assumptions. For an energetic pusher (~40 kJ) that compresses the fuel to an areal density of ~1.07g/cm 2 at ignition, the simulation shows that the Knudsen effect can substantially limit ion temperature rise in runaway burn. While the final yield decreases modestly from kinetic effects of the α particles, large reduction of the fuel reactivity during ignition and runaway burn may require a higher Knudsen loss rate compared to the rise time of the temperatures above ~25 keV when the broad D-T Gamow peak merges into the bulk Maxwellian distribution.« less

Optimal Timing for Early Excision in a Deep Partial Thickness Porcine Burn Model.

PubMed

Toussaint, Jimmy; Chung, Won Taek; Mc Clain, Steve; Raut, Vivek; Singer, Adam J

Many deep partial thickness burns require more than 3 weeks to heal resulting in disfiguring and dysfunctional scarring. Early excision of the eschar has been shown to improve outcomes in deep burns; however, the optimal timing of the excision remains controversial. We compared wound healing and scarring of deep partial thickness burns that were excised at different time points in a porcine model. Deep partial thickness burns (2.5 by 2.5 cm each) were created on the backs of six anesthetized pigs using a previously validated model. The burns were randomly assigned to excision at days 2, 4, or 7 using an electric dermatome. Full thickness 4-mm punch biopsies were obtained at several time points for determination of re-epithelialization and at day 28 for determination of scar depth. Digital imaging was used to calculate percentage wound contraction at day 28. There were no statistically significant differences in wound re-epithelialization at any of the studied time points. Scar depth and percentage wound contraction were also similar among the wounds excised at 2, 4, and 7 days (4.4 ± 1.1 mm vs 3.9 ± 1.1 mm vs 4.1 ± 1.2 mm and 52.9 ± 17.9% vs 52.6 ± 15.6% vs 52.5 ± 13.8%, respectively). Timing of eschar excision (at 2, 4, or 7 days) does not affect the rates of re-epithelialization and scarring in a deep partial thickness porcine burn model. Timing of eschar excision may not change outcomes if performed within the first 2 to 7 days after injury.

Calculations of combustion response profiles and oscillations

NASA Technical Reports Server (NTRS)

Priem, Richard J.; Breisacher, Kevin J.

1993-01-01

The theory and procedures for determining the characteristics of pressure oscillations in rocket engines with prescribed burning rate oscillations are presented. Pressure and velocity oscillations calculated using this procedure are presented for the Space Shuttle Main Engine (SSME) to show the influence of baffles and absorbers on the burning rate oscillations required to achieve neutral stability. Results of calculations to determine local combustion responses using detailed physical models for injection, atomization, and vaporization with gas phase oscillations in baffled and unbaffled SSME combustors are presented. The contributions of the various physical phenomena occurring in a combustor to oscillations in combustion response were determined.

The 3D rocket combustor acoustics model

NASA Technical Reports Server (NTRS)

Priem, Richard J.; Breisacher, Kevin J.

1992-01-01

The theory and procedures for determining the characteristics of pressure oscillations in rocket engines with prescribed burning rate oscillations are presented. Analyses including radial and hub baffles and absorbers can be performed in one, two, and three dimensions. Pressure and velocity oscillations calculated using this procedure are presented for the SSME to show the influence of baffles and absorbers on the burning rate oscillations required to achieve neutral stability. Comparisons are made between the results obtained utilizing 1-D, 2-D, and 3-D assumptions with regards to capturing the physical phenomena of interest and computational requirements.

Flame spread over thick polymethylmethacrylate samples in a simulated and actual microgravity environment

NASA Astrophysics Data System (ADS)

Shah, Tirthesh Jayesh

The NASA Burning and Suppression of Solids-II (BASS II) experiment examines the combustion of different solid materials and material geometries in microgravity. While flames in microgravity are driven by diffusion and weak advection due to crew movements and ventilation, the current NASA spacecraft material selection test method (NASA-STD- 6001 Test 1) is driven by buoyant forces as gravity is present. The overall goal of this project is to understand the burning of intermediate and thick fuels in microgravity, and devise a normal gravity test to apply to future materials. Clear cast polymethylmethacrylate (PMMA) samples 10 cm long by 1 or 2 cm wide with thicknesses ranging from 1-5 mm were investigated. PMMA is the ideal choice since it is widely used and we know its stoichiometric chemistry. Tests included both one sided and two sided burns. Samples are ignited by heating a wire behind the sample. The samples are burned in a flow duct within the Microgravity Science Glovebox (MSG) on the International Space Station (ISS) to ensure true microgravity conditions. The experiment takes place in opposed flow with varying Oxygen concentrations and flow velocities. Flames are recorded on two cameras and later tracked to determine spread rate. Currently we are modeling combustion of PMMA using Fire Dynamics Simulator (FDS 5.5.3) and Smokeview. The entire modelling for BASS-II is done in DNS mode because of the laminar conditions and small domain. In DNS mode the Navier Stokes equations are solved without the Turbulence model. The model employs the same test sample and MSG geometry as the experiment; but in 2D. The experimental data gave upstream velocity at several points using an anemometer. A flow profile for the inlet velocity is obtained using Matlab and input into the model. The flame spread rates obtained after tracking are then compared with the experimental data and the results follow the trends but the spread rates are higher.

Determination of Optimal Amikacin Dosing Regimens for Pediatric Patients With Burn Wound Sepsis.

PubMed

Yu, Tian; Stockmann, Chris; Healy, Daniel P; Olson, Jared; Wead, Stephanie; Neely, Alice N; Kagan, Richard J; Spigarelli, Michael G; Sherwin, Catherine M T

2015-01-01

This study aimed to develop optimal amikacin dosing regimens for the empirical treatment of Gram-negative bacterial sepsis in pediatric patients with burn injuries. A pharmacodynamic (PD) target in which the peak concentration (Cmax) is ≥8 times the minimum inhibitory concentration (MIC) (Cmax/MIC ≥ 8) is reflective of optimal bactericidal activity and has been used to predict clinical outcomes. Population pharmacokinetic modeling was performed in NONMEM 7.2 for pediatric patients with and without burn injuries. Amikacin pharmacokinetic parameters were compared between the two groups and multiple dosing regimens were simulated using MATLAB to achieve the PD target in ≥90% of patients with burn injuries. The pharmacokinetic analysis included 282 amikacin concentrations from 70 pediatric patients with burn injuries and 99 concentrations from 32 pediatric patients without burns. A one-compartment model with first-order elimination described amikacin pharmacokinetics well for both groups. Clearance (CL) was significantly higher in patients with burn injuries than in patients without (7.22 vs 5.36 L/h, P < .001). The volume of distribution (V) was also significantly increased in patients with burn injuries (22.7 vs 18.7 L, P < .01). Weight significantly influenced amikacin CL (P < .001) and V (P < .001) for both groups. Model-based simulations showed that a higher amikacin dose (≥25 mg/kg) achieved a Cmax/MIC ≥8 in ≥90% of patients with assumed infections of organisms with an MIC = 8 mg/L. Amikacin pharmacokinetics are altered in patients with burn injuries, including a significant increase in CL and V. In simulations, increased doses (≥25 mg/kg) led to improved PD target attainment rates. Further clinical evaluation of this proposed dosing regimen is warranted to assess clinical and microbiological outcomes in pediatric patients with burn wound sepsis.

Turbulent Nuclear Burning of Carbon Fuel in Double-Degenerate White Dwarfs

NASA Astrophysics Data System (ADS)

Mozumdar, Pritom; Fisher, Robert

2018-01-01

Type Ia supernovae (SNe Ia) are of interest as standardizable cosmological candles, though their stellar progenitors are still poorly understood. The double-degenerate (DD) channel is promising, but the mechanism for the explosion remains a matter of active investigation. A long-standing problem in modeling SNe Ia is the fact that 3D simulations leave the length scales crucial for a possible detonation unresolved. In this work, we have performed local 3D hydrodynamical adaptive mesh refinement simulations of driven turbulence for various initial conditions characteristic of the DD scenario, which are capable of capturing length scales relevant to the Zel’dovich gradient mechanism. Because the carbon burning rate is highly sensitive to temperature in this regime, we demonstrate that turbulence can dramatically enhance the nuclear burning rate, and we investigate the connection to a possible detonation.

Continuously graded extruded polymer composites for energetic applications fabricated using twin-screw extrusion processing technology

NASA Astrophysics Data System (ADS)

Gallant, Frederick M.

A novel method of fabricating functionally graded extruded composite materials is proposed for propellant applications using the technology of continuous processing with a Twin-Screw Extruder. The method is applied to the manufacturing of grains for solid rocket motors in an end-burning configuration with an axial gradient in ammonium perchlorate volume fraction and relative coarse/fine particle size distributions. The fabrication of functionally graded extruded polymer composites with either inert or energetic ingredients has yet to be investigated. The lack of knowledge concerning the processing of these novel materials has necessitated that a number of research issues be addressed. Of primary concern is characterizing and modeling the relationship between the extruder screw geometry, transient processing conditions, and the gradient architecture that evolves in the extruder. Recent interpretations of the Residence Time Distributions (RTDs) and Residence Volume Distributions (RVDs) for polymer composites in the TSE are used to develop new process models for predicting gradient architectures in the direction of extrusion. An approach is developed for characterizing the sections of the extrudate using optical, mechanical, and compositional analysis to determine the gradient architectures. The effects of processing on the burning rate properties of extruded energetic polymer composites are characterized for homogeneous formulations over a range of compositions to determine realistic gradient architectures for solid rocket motor applications. The new process models and burning rate properties that have been characterized in this research effort will be the basis for an inverse design procedure that is capable of determining gradient architectures for grains in solid rocket motors that possess tailored burning rate distributions that conform to user-defined performance specifications.

Short-term responses of soil nitrogen mineralization, nitrification and denitrification to prescribed burning in a suburban forest ecosystem of subtropical Australia.

PubMed

Zhang, Manyun; Wang, Weijin; Wang, Dianjie; Heenan, Marijke; Xu, Zhihong

2018-06-17

As an anthropogenic disturbance, prescribed burning may alter the biogeochemistries of nutrients, including nitrogen (N) cycling, in forest ecosystems. This study aimed to examine the changes in N mineralization, nitrification and denitrification rates following prescribed burning in a suburban forest located in subtropical Australia and assess the interactive relationships among soil properties, functional gene abundances and N transformation rates. After a prescribed burning event, soil pH value increased, but soil labile carbon and mineral N contents decreased. Net N mineralization rates, potential nitrification rates and ammonium-oxidizing archaea and bacteria (AOA and AOB) amoA gene abundances in the soils all increased after 3 months of the prescribed burning. However, the abundances of different functional genes related to denitrification changed differently after the prescribed burning. The net N mineralization rates could be best described by soil abiotic properties, rather than functional gene abundances. In contrast, potential denitrification rates were positively related to soil nirK gene abundances. Potential nitrification rates could be influenced by both soil chemical and microbial properties. The results revealed that the prescribed burning might increase N mineralization and nitrification rates in the forest soil. Copyright © 2018 Elsevier B.V. All rights reserved.

Two-Year Gender Differences in Satisfaction With Appearance After Burn Injury and Prediction of Five-Year Depression: A Latent Growth Curve Approach.

PubMed

Al Ghriwati, Nour; Sutter, Megan; Pierce, Bradford S; Perrin, Paul B; Wiechman, Shelley A; Schneider, Jeffrey C

2017-11-01

To use latent growth curve and longitudinal structural equation modeling to examine the 2-year trajectory of satisfaction with appearance in adults with burn injury, and that trajectory's effect on depression 5 years after burn injury. Data were collected at discharge after burn injury hospitalization and at 6 months, 1 year, 2 years, and 5 years postdischarge. The Burn Model Systems (BMS) program consisted of a data center and 5 participating burn centers. The sample consisted of adults (N=720) who were hospitalized for a burn injury, enrolled in the BMS database, and completed measures at least once throughout the 5-year study duration. Not applicable. Satisfaction With Appearance Scale and Patient Health Questionnaire-9 (depression). Women with burn injury reported higher levels of dissatisfaction with their appearance in comparison to their male counterparts over the 2 years after discharge. Individuals with a larger total body surface area (TBSA) affected by a burn also reported greater body dissatisfaction across the postdischarge 2-year period. Results did not support significant gender or TBSA differences in the rate of change of body dissatisfaction trajectories across these 2 years. Individuals with greater body dissatisfaction at 6 months postdischarge tended to have higher depressive symptoms at 5 years. Six month postdischarge, body dissatisfaction scores also mediated the effects of gender and TBSA on depressive symptoms 5 years later. It is recommended that individuals with heightened body image dissatisfaction after a burn, particularly women and those with larger TBSA, participate in evidence-based psychosocial interventions to improve long-term adjustment. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Experiments and Model Development for the Investigation of Sooting and Radiation Effects in Microgravity Droplet Combustion

NASA Technical Reports Server (NTRS)

Choi, Mun Young; Yozgatligil, Ahmet; Dryer, Frederick L.; Kazakov, Andrei; Dobashi, Ritsu

2001-01-01

Today, despite efforts to develop and utilize natural gas and renewable energy sources, nearly 97% of the energy used for transportation is derived from combustion of liquid fuels, principally derived from petroleum. While society continues to rely on liquid petroleum-based fuels as a major energy source in spite of their finite supply, it is of paramount importance to maximize the efficiency and minimize the environmental impact of the devices that burn these fuels. The development of improved energy conversion systems, having higher efficiencies and lower emissions, is central to meeting both local and regional air quality standards. This development requires improvements in computational design tools for applied energy conversion systems, which in turn requires more robust sub-model components for combustion chemistry, transport, energy transport (including radiation), and pollutant emissions (soot formation and burnout). The study of isolated droplet burning as a unidimensional, time dependent model diffusion flame system facilitates extensions of these mechanisms to include fuel molecular sizes and pollutants typical of conventional and alternative liquid fuels used in the transportation sector. Because of the simplified geometry, sub-model components from the most detailed to those reduced to sizes compatible for use in multi-dimensional, time dependent applied models can be developed, compared and validated against experimental diffusion flame processes, and tested against one another. Based on observations in microgravity experiments on droplet combustion, it appears that the formation and lingering presence of soot within the fuel-rich region of isolated droplets can modify the burning rate, flame structure and extinction, soot aerosol properties, and the effective thermophysical properties. These observations led to the belief that perhaps one of the most important outstanding contributions of microgravity droplet combustion is the observation that in the absence of asymmetrical forced and natural convection, a soot shell is formed between the droplet surface and the flame, exerting an influence on the droplet combustion response far greater than previously recognized. The effects of soot on droplet burning parameters, including burning rate, soot shell dynamics, flame structure, and extinction phenomena provide significant testing parameters for studying the structure and coupling of soot models with other sub-model components.

Burn Incidence and Treatment in the U.S.

MedlinePlus

... state health data systems, and the National Burn Repository (NBR) of the American Burn Association (ABA). ABA ... Burn Admissions to Burn Centers (ABA National Burn Repository 2015) Survival Rate: 96.8% Gender: 68% Male, ...

Burden of burns in Portugal, 2000-2013: A clinical and economic analysis of 26,447 hospitalisations.

PubMed

Santos, João V; Oliveira, Andreia; Costa-Pereira, Altamiro; Amarante, José; Freitas, Alberto

2016-06-01

There is a lack of recent and nation-wide epidemiological studies of burns in Europe, mainly in southern Europe. There are no recent studies describing the clinical and economic burden of burns in this European area. Hence, this research aimed to describe the clinical and economic burden of burn hospitalisations in Portugal. A retrospective observational study was performed and the Portuguese hospitalisation database of public hospitals was used; all inpatients, discharged between 2000 and 2013, with a main or secondary diagnosis of burns (ICD-9-CM: 940.xx-949.xx) were taken into account. Furthermore, admissions to hospitals with and without burn centres were compared. A total of 26,447 burn hospitalisations were registered (mean of 1889burn admissions/year). The total hospitalisation rate was of 18.9hospitalisations/100,000inhabitants/year, and there was a higher incidence of male patients. Burn hospitalisations and hospitalisation rates are significantly decreasing - mostly in 0-14-year-old patients - and children below the age of 5 years represented a fifth of all admissions. Besides the important morbidity, the in-hospital mortality rate was of 4.4%. With a total annual charge of almost 13million Euros, the average cost per burn admission is increasing, and reached 8032Euros in 2013. Additionally, more than half of the patients admitted to hospitals without burn centres were not transferred to hospitals with burn centres, not following the European Burns Association transferral criteria. As the largest southern European nation-wide epidemiological study of burn patients, this research highlights that burn admissions, as well as hospitalisation rates, are decreasing significantly. This was particularly obvious among the youngest patients despite the fact that the numbers still remain very high. Moreover, the in-hospital mortality rate is still excessively high and the burn transferral criteria are not being followed. Thus, it is important to improve preventive measures, reach out to and educate providers about the burn transferral criteria, and develop specific health care strategies for children with these injuries. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

ERMiT: Estimating Post-Fire Erosion in Probabilistic Terms

NASA Astrophysics Data System (ADS)

Pierson, F. B.; Robichaud, P. R.; Elliot, W. J.; Hall, D. E.; Moffet, C. A.

2006-12-01

Mitigating the impact of post-wildfire runoff and erosion on life, property, and natural resources have cost the United States government tens of millions of dollars over the past decade. The decision of where, when, and how to apply the most effective mitigation treatments requires land managers to assess the risk of damaging runoff and erosion events occurring after a fire. The Erosion Risk Management Tool (ERMiT) is a web-based application that estimates erosion in probabilistic terms on burned and recovering forest, range, and chaparral lands. Unlike most erosion prediction models, ERMiT does not provide `average annual erosion rates;' rather, it provides a distribution of erosion rates with the likelihood of their occurrence. ERMiT combines rain event variability with spatial and temporal variabilities of hillslope burn severity, soil properties, and ground cover to estimate Water Erosion Prediction Project (WEPP) model input parameter values. Based on 20 to 40 individual WEPP runs, ERMiT produces a distribution of rain event erosion rates with a probability of occurrence for each of five post-fire years. Over the 5 years of modeled recovery, the occurrence probability of the less erodible soil parameters is increased and the occurrence probability of the more erodible soil parameters is decreased. In addition, the occurrence probabilities and the four spatial arrangements of burn severity (arrangements of overland flow elements (OFE's)), are shifted toward lower burn severity with each year of recovery. These yearly adjustments are based on field measurements made through post-fire recovery periods. ERMiT also provides rain event erosion rate distributions for hillslopes that have been treated with seeding, straw mulch, straw wattles and contour-felled log erosion barriers. Such output can help managers make erosion mitigation treatment decisions based on the probability of high sediment yields occurring, the value of resources at risk for damage, cost, and other management considerations.

Biomass burning: A significant source of nutrients for Andean rainforests

NASA Astrophysics Data System (ADS)

Fabian, P. F.; Rollenbeck, R.; University Of Marburg, Germany

2010-12-01

Regular rain and fogwater sampling in the Podocarpus National Park,on the humid eastern slopes of the Ecuadorian Andes,has been carried out since 2002.The samples,accumulated over about 1-week intervals,were analysed for pH,conductivity,and major ions (K+, Na+, NH4+, Ca2+, Mg2+, Cl-, SO4 2-, NO3-, PO4 3- ).Annual deposition rates of these ions which, due to poor acidic soils with low mineralization rates,constitute the dominant nutrient supply to the mountaineous rainforests, and major ion sources could be determined using back trajectories,along with satellite data. While most of the Na, Cl, and K as well as Ca and Mg input was found to originate from natural oceanic and desert dust sources,respectively (P.Fabian et al.,Adv.Geosci.22,85-94, 2009), NO3, NH4, and about 90% of SO4 (about 10 % is from active volcanoes) are almost entirely due to anthropogenic sources,most likely biomass burning. Industrial and transportation emissions and other pollutants,however,act in a similar way as the precursors produced by biomass burning.For quantifying the impacts of biomass burning vs. those of anthropogenic sources other than biomass burning we used recently established emission inventories,along with simplified model calculations on back trajectories.First results yielding significant contributions of biomass burning will be discussed.

Performance characterization of complex fuel port geometries for hybrid rocket fuel grains

NASA Astrophysics Data System (ADS)

Bath, Andrew

This research investigated the 3D printing and burning of fuel grains with complex geometry and the development of software capable of modeling and predicting the regression of a cross-section of these complex fuel grains. The software developed did predict the geometry to a fair degree of accuracy, especially when enhanced corner rounding was turned on. The model does have some drawbacks, notably being relatively slow, and does not perfectly predict the regression. If corner rounding is turned off, however, the model does become much faster; although less accurate, this method does still predict a relatively accurate resulting burn geometry, and is fast enough to be used for performance-tuning or genetic algorithms. In addition to the modeling method, preliminary investigations into the burning behavior of fuel grains with a helical flow path were performed. The helix fuel grains have a regression rate of nearly 3 times that of any other fuel grain geometry, primarily due to the enhancement of the friction coefficient between the flow and flow path.

Turbulent combustion in aluminum-air clouds for different scale explosion fields

NASA Astrophysics Data System (ADS)

Kuhl, Allen L.; Balakrishnan, Kaushik; Bell, John B.; Beckner, Vincent E.

2017-01-01

This paper explores "scaling issues" associated with Al particle combustion in explosions. The basic idea is the following: in this non-premixed combustion system, the global burning rate is controlled by rate of turbulent mixing of fuel (Al particles) with air. From similarity considerations, the turbulent mixing rates should scale with the explosion length and time scales. However, the induction time for ignition of Al particles depends on an Arrhenius function, which is independent of the explosion length and time. To study this, we have performed numerical simulations of turbulent combustion in unconfined Al-SDF (shock-dispersed-fuel) explosion fields at different scales. Three different charge masses were assumed: 1-g, 1-kg and 1-T Al-powder charges. We found that there are two combustion regimes: an ignition regime—where the burning rate decays as a power-law function of time, and a turbulent combustion regime—where the burning rate decays exponentially with time. This exponential dependence is typical of first order reactions and the more general concept of Life Functions that control the dynamics of evolutionary systems. Details of the combustion model are described. Results, including mean and rms profiles in combustion cloud and fuel consumption histories, are presented.

Comparing the reported burn conditions for different severity burns in porcine models: a systematic review.

PubMed

Andrews, Christine J; Cuttle, Leila

2017-12-01

There are many porcine burn models that create burns using different materials (e.g. metal, water) and different burn conditions (e.g. temperature and duration of exposure). This review aims to determine whether a pooled analysis of these studies can provide insight into the burn materials and conditions required to create burns of a specific severity. A systematic review of 42 porcine burn studies describing the depth of burn injury with histological evaluation is presented. Inclusion criteria included thermal burns, burns created with a novel method or material, histological evaluation within 7 days post-burn and method for depth of injury assessment specified. Conditions causing deep dermal scald burns compared to contact burns of equivalent severity were disparate, with lower temperatures and shorter durations reported for scald burns (83°C for 14 seconds) compared to contact burns (111°C for 23 seconds). A valuable archive of the different mechanisms and materials used for porcine burn models is presented to aid design and optimisation of future models. Significantly, this review demonstrates the effect of the mechanism of injury on burn severity and that caution is recommended when burn conditions established by porcine contact burn models are used by regulators to guide scald burn prevention strategies. © 2017 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

New higher-order Godunov code for modelling performance of two-stage light gas guns

NASA Technical Reports Server (NTRS)

Bogdanoff, D. W.; Miller, R. J.

1995-01-01

A new quasi-one-dimensional Godunov code for modeling two-stage light gas guns is described. The code is third-order accurate in space and second-order accurate in time. A very accurate Riemann solver is used. Friction and heat transfer to the tube wall for gases and dense media are modeled and a simple nonequilibrium turbulence model is used for gas flows. The code also models gunpowder burn in the first-stage breech. Realistic equations of state (EOS) are used for all media. The code was validated against exact solutions of Riemann's shock-tube problem, impact of dense media slabs at velocities up to 20 km/sec, flow through a supersonic convergent-divergent nozzle and burning of gunpowder in a closed bomb. Excellent validation results were obtained. The code was then used to predict the performance of two light gas guns (1.5 in. and 0.28 in.) in service at the Ames Research Center. The code predictions were compared with measured pressure histories in the powder chamber and pump tube and with measured piston and projectile velocities. Very good agreement between computational fluid dynamics (CFD) predictions and measurements was obtained. Actual powder-burn rates in the gun were found to be considerably higher (60-90 percent) than predicted by the manufacturer and the behavior of the piston upon yielding appears to differ greatly from that suggested by low-strain rate tests.

Burning of CP Titanium (Grade 2) in Oxygen-Enriched Atmospheres

NASA Technical Reports Server (NTRS)

Stoltzfus, Joel M.; Jeffers, Nathan; Gallus, Timothy D.

2012-01-01

The flammability in oxygen-enriched atmospheres of commercially pure (CP) titanium rods as a function of diameter and test gas pressure was determined. Test samples of varying diameters were ignited at the bottom and burned upward in 70% O2/balance N2 and in 99.5+% O2 at various pressures. The burning rate of each ignited sample was determined by observing the apparent regression rate of the melting interface (RRMI) of the burning samples. The burning rate or RRMI increased with decreasing test sample diameter and with increasing test gas pressure and oxygen concentration

Mental health outcomes of burn: A longitudinal population-based study of adults hospitalized for burns.

PubMed

Logsetty, Sarvesh; Shamlou, Amir; Gawaziuk, Justin P; March, Justin; Doupe, Malcolm; Chateau, Dan; Hoppensack, Mike; Khan, Sazzadul; Medved, Maria; Leslie, William D; Enns, Murray W; Stein, Murray B; Asmundson, Gordon J G; Sareen, Jitender

2016-06-01

This study investigates the increased risk of mental health outcomes and health care utilization associated with burn with two year of follow-up using a longitudinal population-based matched cohort design. Adult burn survivors (n=157) were identified from a provincial burn registry and matched 1:5 with non-burn control subjects from the general population (matching variables age and gender). The prevalence of mental health outcomes and the rates of health care utilization between the groups were compared for the 2years pre and post index date using anonymously linked population-based administrative health care data. Rates were adjusted for age, gender and sociodemographic characteristics. While the burn cohort had an increased prevalence of mental health problems after burn compared to the control cohort, the burn group also had an increased prevalence of pre-burn depression (16.6% vs 7.8%; p=0.0005) and substance use disorders (8.9% vs 3.2%; p=0.001) when compared to controls. Once the pre-existing prevalence of mental illness was taken into account there was no significant change in the prevalence of mental health problems when comparing the burn group to controls over time. Although burns may not increase rates of mental health issues and health care utilization, burn survivors are a vulnerable group who already demonstrate increased rates of psychopathology and need for care. The present study highlights the importance of assessment and treatment of mental health outcomes in this population. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Burns - resources

MedlinePlus

Resources - burns ... The following organizations are good resources for information on burns : Burns Recovered -- brsg.org Model Systems Knowledge Translation Center - Burn Model Systems -- www.msktc.org/burn http:// ...

Economic Spillovers From Public Investments in Medical Countermeasures: A Case Study of a Burn Debridement Product.

PubMed

Farahati, Farah; Nystrom, Scott; Howell, David R; Jaffe, Richard

2017-12-01

The US federal government invests in the development of medical countermeasures for addressing adverse health effects to the civilian population from chemical, biological, and radiological or nuclear threats. We model the potential economic spillover effects in day-to-day burn care for a federal investment in a burn debridement product for responding to an improvised nuclear device. We identify and assess 4 primary components for projecting the potential economic spillover benefits of a burn debridement product: (1) market size, (2) clinical effectiveness and cost-effectiveness, (3) product cost, and (4) market adoption rates. Primary data sources were the American Burn Association's 2015 National Burn Repository Annual Report of Data and published clinical studies used to gain European approval for the burn debridement product. The study results showed that if approved for use in the United States, the burn debridement product has potential economic spillover benefits exceeding the federal government's initial investment of $24 million a few years after introduction into the burn care market. Economic spillover analyses can help to inform the prioritizing of scarce resources for research and development of medical countermeasures by the federal government. Future federal medical countermeasure research and development investments could incorporate economic spillover analysis to assess investment options. (Disaster Med Public Health Preparedness. 2017;11:711-719).

Comparing the Global Charcoal Database with Burned Area Trends from an Offline Fire Model Driven by the NCAR Last Millennium Ensemble

NASA Astrophysics Data System (ADS)

Schaefer, A.; Magi, B. I.; Marlon, J. R.; Bartlein, P. J.

2017-12-01

This study uses an offline fire model driven by output from the NCAR Community Earth System Model Last Millennium Ensemble (LME) to evaluate how climate, ecological, and human factors contributed to burned area over the past millennium, and uses the Global Charcoal Database (GCD) record of fire activity as a constraint. The offline fire model is similar to the fire module within the NCAR Community Land Model. The LME experiment includes 13 simulations of the Earth system from 850 CE through 2005 CE, and the fire model simulates burned area using LME climate and vegetation with imposed land use and land cover change. The fire model trends are compared to GCD records of charcoal accumulation rates derived from sediment cores. The comparisons are a way to assess the skill of the fire model, but also set up a methodology to directly test hypotheses of the main drivers of fire patterns over the past millennium. The focus is on regions selected from the GCD with high data density, and that have lake sediment cores that best capture the last millennium. Preliminary results are based on a fire model which excludes burning cropland and pasture land cover types, but this allows some assessment of how climate variability is captured by the fire model. Generally, there is good agreement between modeled burned area trends and fire trends from GCD for many regions of interest, suggesting the strength of climate variability as a control. At the global scale, trends and features are similar from 850 to 1700, which includes the Medieval Climate Anomaly and the Little Ice Age. After 1700, the trends significantly deviate, which may be due to non-cultivated land being converted to cultivated. In key regions of high data density in the GCD such as the Western USA, the trends agree from 850 to 1200 but diverge from 1200 to 1300. From 1300 to 1800, the trends show good agreement again. Implementing processes to include burning cultivated land within the fire model is anticipated to improve the agreement, but also to test the sensitivity of models to different drivers of fire.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karlstad, M.D.; DeMichele, S.J.; Istfan, N.

The effects of burn and first-pass splanchnic leucine extraction (FPE) on protein kinetics and energy expenditure were assessed by measuring O/sub 2/ consumption, CO/sub 2/ production, nitrogen balance, leucine kinetics, and tissue fractional protein synthetic rates (FSR-%/day) in enterally fed rats. Anesthetized male rats (200 g) were scalded on their dorsum with boiling water (25-30% body surface area) and enterally fed isovolemic diets that provided 60 kcal/day and 2.4 g of amino acids/day for 3 days. Controls were not burned. An intravenous or intragastric infusion of L-(1-/sup 14/C)leucine was used to assess protein kinetics on day 3. FPE was takenmore » as the ratio of intragastric to intravenous plasma leucine specific activity. There was a 69% reduction in cumulative nitrogen balance (P less than 0.001) and a 17-19% increase in leucine oxidation (P less than 0.05) and total energy expenditure (P less than 0.01) in burned rats. A 15% decrease in plasma leucine clearance (P less than 0.05) was accompanied by a 20% increase in plasma (leucine) (P less than 0.01) in burned rats. Burn decreased rectus muscle FSR from 5.0 +/- 0.4 to 3.5 +/- 0.5 (P less than 0.05) and increased liver FSR from 19.0 +/- 0.5 to 39.2 +/- 3.4 (P less than 0.01). First pass extraction of dietary leucine by the splanchnic bed was 8% in controls and 26% in burned rats. Leucine kinetics corrected for FPE showed increased protein degradation with burn that was not evident without FPE correction. This hypermetabolic burn model can be useful in the design of enteral diets that optimize rates of protein synthesis and degradation.« less

[Effect of prescribed burning on grassland nitrogen gross mineralization and nitrification].

PubMed

Li, Yuzhong; Zhu, Tingcheng; Li, Jiandong; Zhou, Daowei

2003-02-01

The seasonal dynamics of nitrogen gross mineralization, nitrification, and mineral nitrogen consumption rates in burned and unburned Leymus chinensis grasslands were studied with 15N pool dilution technique. The results indicated that the gross mineralization and nitrification rates in burned area were higher than those in unburned area in April and May, and lower than those in unburned area in September. NH4(+)-N consumption rates were higher than unburned area in April and May, and lower in September. NO3(-)-N consumption rates were higher than control in April and May, and lower than control in July and September. The NH4(+)-N concentrations were higher in burned area in April, May and July, and no difference in September. NO3(-)-N concentrations were no difference between burned and unburned areas in April and May, and higher in burned areas in July and September.

Burn mortality in patients with preexisting cardiovascular disease.

PubMed

Knowlin, Laquanda; Reid, Trista; Williams, Felicia; Cairns, Bruce; Charles, Anthony

2017-08-01

Burn shock, a complex process, which develops following burn leads to severe and unique derangement of cardiovascular function. Patients with preexisting comorbidities such as cardiovascular diseases may be more susceptible. We therefore sought to examine the impact of preexisting cardiovascular disease on burn outcomes. A retrospective analysis of patients admitted to a regional burn center from 2002 to 2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA, pre-existing comorbidities, and length of ICU/hospital stay. Bivariate analysis was performed and Poisson regression modeling was utilized to estimate the incidence of being in the ICU and mortality. There were a total of 5332 adult patients admitted over the study period. 6% (n=428) had a preexisting cardiovascular disease. Cardiovascular disease patients had a higher mortality rate (16%) compared to those without cardiovascular disease (3%, p<0.001). The adjusted Poisson regression model to estimate incidence risk of being in intensive care unit in patients with cardiovascular disease was 33% higher compared to those without cardiovascular disease (IRR=1.33, 95% CI=1.22-1.47). The risk for mortality is 42% higher (IRR=1.42, 95% CI=1.10-1.84) for patients with pre-existing cardiovascular disease compared to those without cardiovascular disease after controlling for other covariates. Preexisting cardiovascular disease significantly increases the risk of intensive care unit admission and mortality in burn patients. Given the increasing number of Americans with cardiovascular diseases, there will likely be a greater number of individuals at risk for worse outcomes following burn. This knowledge can help with burn prognostication. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Pain and itch outcome trajectories differ among European American and African American survivors of major thermal burn injury.

PubMed

Mauck, Matthew C; Smith, Jennifer; Shupp, Jeffrey W; Weaver, Mark A; Liu, Andrea; Bortsov, Andrey V; Lateef, Bilal; Jones, Samuel W; Williams, Felicia; Hwang, James; Karlnoski, Rachel; Smith, David J; Cairns, Bruce A; McLean, Samuel A

2017-11-01

More than half of individuals experiencing major thermal burn injury (MThBI) receive an autologous skin graft (autograft), in which skin is removed from a healthy "donor" site and transplanted to the burn site. Persistent pain and itch at the graft site are major causes of suffering and disability in MThBI survivors. African Americans have a higher risk of MThBI, and in other clinical settings African Americans experience a greater burden of pain and itch relative to European Americans. However, to our knowledge, ethnic differences in skin graft site pain and itch outcomes after MThBI have not been assessed. We evaluated skin graft site pain and itch severity (0-10 Numeric Rating Scale [NRS]) over 1 year in a prospective multicenter cohort sample of African Americans and European Americans. In adjusted linear mixed models, African Americans experienced a slower rate of pain resolution in the acute phase of recovery (β = -0.05 vs -0.08 NRS points per day, P < 0.001), which resulted in a higher pain severity in the persistent phase of recovery (NRS mean difference = 1.21, 95% confidence interval [0.12-2.29]), although not statistically significant after correction for multiple comparisons. African Americans also experience greater itch severity in 6 weeks to 12 months after burn injury compared with European Americans (NRS mean difference = 1.86 [0.80-2.93]), which results from a faster rate of itch development in African Americans in the acute recovery phase after burn injury. Future studies may improve outcomes in African Americans and lead to new pathogenic insights that benefit all burn injury survivors.

Evaluation of a locally homogeneous flow model of spray combustion

NASA Technical Reports Server (NTRS)

Mao, C. P.; Szekely, G. A., Jr.; Faeth, G. M.

1980-01-01

A model of spray combustion which employs a second-order turbulence model was developed. The assumption of locally homogeneous flow is made, implying infinitely fast transport rates between the phase. Measurements to test the model were completed for a gaseous n-propane flame and an air atomized n-pentane spray flame, burning in stagnant air at atmospheric pressure. Profiles of mean velocity and temperature, as well as velocity fluctuations and Reynolds stress, were measured in the flames. The predictions for the gas flame were in excellent agreement with the measurements. The predictions for the spray were qualitatively correct, but effects of finite rate interphase transport were evident, resulting in a overstimation of the rate development of the flow. Predictions of spray penetration length at high pressures, including supercritical combustion conditions, were also completed for comparison with earlier measurements. Test conditions involved a pressure atomized n-pentane spray, burning in stagnant air at pressures of 3, 5, and 9 MPa. The comparison between predictions and measurements was fair. This is not a very sensitive test of the model, however, and further high pressure experimental and theoretical results are needed before a satisfactory assessment of the locally homogeneous flow approximation can be made.

Progress in the development of the MARBLE platform for studying thermonuclear burn in the presence of heterogeneous mix on OMEGA and the National Ignition Facility

NASA Astrophysics Data System (ADS)

Murphy, T. J.; Douglas, M. R.; Fincke, J. R.; Olson, R. E.; Cobble, J. A.; Haines, B. M.; Hamilton, C. E.; Lee, M. N.; Oertel, J. A.; Parra-Vasquez, N. A. G.; Randolph, R. B.; Schmidt, D. W.; Shah, R. C.; Smidt, J. M.; Tregillis, I. L.

2016-05-01

Mix of ablator material into fuel of an ICF capsule adds non-burning material, diluting the fuel and reducing burn. The amount of the reduction is dependent in part on the morphology of the mix. A probability distribution function (PDF) burn model has been developed [6] that utilizes the average concentration of mixed materials as well as the variance in this quantity across cells provided by the BHR turbulent transport model [3] and its revisions [4] to describe the mix in terms of a PDF of concentrations of fuel and ablator material, and provides the burn rate in mixed material. Work is underway to develop the MARBLE ICF platform for use on the National Ignition Facility in experiments to quantify the influence of heterogeneous mix on fusion burn. This platform consists of a plastic (CH) capsule filled with a deuterated plastic foam (CD) with a density of a few tens of milligrams per cubic centimeter, with tritium gas filling the voids in the foam. This capsule will be driven using x-ray drive on NIF, and the resulting shocks will induce turbulent mix that will result in the mixing of deuterium from the foam with the tritium gas. In order to affect the morphology of the mix, engineered foams with voids of diameter up to 100 microns will be utilized. The degree of mix will be determined from the ratio of DT to DD neutron yield. As the mix increases, the yield from reactions between the deuterium of the CD foam with tritium from the gas will increase. The ratio of DT to DD neutrons will be compared to a variation of the PDF burn model that quantifies reactions from initially separated reactants.

What could have caused pre-industrial biomass burning emissions to exceed current rates?

NASA Astrophysics Data System (ADS)

van der Werf, G. R.; Peters, W.; van Leeuwen, T. T.; Giglio, L.

2013-01-01

Recent studies based on trace gas mixing ratios in ice cores and charcoal data indicate that biomass burning emissions over the past millennium exceeded contemporary emissions by up to a factor of 4 for certain time periods. This is surprising because various sources of biomass burning are linked with population density, which has increased over the past centuries. We have analysed how emissions from several landscape biomass burning sources could have fluctuated to yield emissions that are in correspondence with recent results based on ice core mixing ratios of carbon monoxide (CO) and its isotopic signature measured at South Pole station (SPO). Based on estimates of contemporary landscape fire emissions and the TM5 chemical transport model driven by present-day atmospheric transport and OH concentrations, we found that CO mixing ratios at SPO are more sensitive to emissions from South America and Australia than from Africa, and are relatively insensitive to emissions from the Northern Hemisphere. We then explored how various landscape biomass burning sources may have varied over the past centuries and what the resulting emissions and corresponding CO mixing ratio at SPO would be, using population density variations to reconstruct sources driven by humans (e.g., fuelwood burning) and a new model to relate savanna emissions to changes in fire return times. We found that to match the observed ice core CO data, all savannas in the Southern Hemisphere had to burn annually, or bi-annually in combination with deforestation and slash and burn agriculture exceeding current levels, despite much lower population densities and lack of machinery to aid the deforestation process. While possible, these scenarios are unlikely and in conflict with current literature. However, we do show the large potential for increased emissions from savannas in a pre-industrial world. This is mainly because in the past, fuel beds were probably less fragmented compared to the current situation; satellite data indicates that the majority of savannas have not burned in the past 10 yr, even in Africa, which is considered "the burning continent". Although we have not considered increased charcoal burning or changes in OH concentrations as potential causes for the elevated CO concentrations found at SPO, it is unlikely they can explain the large increase found in the CO concentrations in ice core data. Confirmation of the CO ice core data would therefore call for radical new thinking about causes of variable global fire rates over recent centuries.

Time-resolved analysis of particle emissions from residential biomass combustion - Emissions of refractory black carbon, PAHs and organic tracers

NASA Astrophysics Data System (ADS)

Nielsen, Ingeborg E.; Eriksson, Axel C.; Lindgren, Robert; Martinsson, Johan; Nyström, Robin; Nordin, Erik Z.; Sadiktsis, Ioannis; Boman, Christoffer; Nøjgaard, Jacob K.; Pagels, Joakim

2017-09-01

Time-resolved particle emissions from a conventional wood stove were investigated with aerosol mass spectrometry to provide links between combustion conditions, emission factors, mixing state of refractory black carbon and implications for organic tracer methods. The addition of a new batch of fuel results in low temperature pyrolysis as the fuel heats up, resulting in strong, short-lived, variable emission peaks of organic aerosol-containing markers of anhydrous sugars, such as levoglucosan (fragment at m/z 60). Flaming combustion results in emissions dominated by refractory black carbon co-emitted with minor fractions of organic aerosol and markers of anhydrous sugars. Full cycle emissions are an external mixture of larger organic aerosol-dominated and smaller thinly coated refractory black carbon particles. A very high burn rate results in increased full cycle mass emission factors of 66, 2.7, 2.8 and 1.3 for particulate polycyclic aromatic hydrocarbons, refractory black carbon, total organic aerosol and m/z 60, respectively, compared to nominal burn rate. Polycyclic aromatic hydrocarbons are primarily associated with refractory black carbon-containing particles. We hypothesize that at very high burn rates, the central parts of the combustion zone become air starved, leading to a locally reduced combustion temperature that reduces the conversion rates from polycyclic aromatic hydrocarbons to refractory black carbon. This facilitates a strong increase of polycyclic aromatic hydrocarbons emissions. At nominal burn rates, full cycle emissions based on m/z 60 correlate well with organic aerosol, refractory black carbon and particulate matter. However, at higher burn rates, m/z 60 does not correlate with increased emissions of polycyclic aromatic hydrocarbons, refractory black carbon and organic aerosol in the flaming phase. The new knowledge can be used to advance source apportionment studies, reduce emissions of genotoxic compounds and model the climate impacts of refractory black carbon, such as absorption enhancement by lensing.

The smoke-fireplume model : tool for eventual application to prescribed burns and wildland fires.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, D. F.; Dunn, W. E.; Lazaro, M. A.

Land managers are increasingly implementing strategies that employ the use of fire in prescribed burns to sustain ecosystems and plan to sustain the rate of increase in its use over the next five years. In planning and executing expanded use of fire in wildland treatment it is important to estimate the human health and safety consequences, property damage, and the extent of visibility degradation from the resulting conflagration-pyrolysis gases, soot and smoke generated during flaming, smoldering and/or glowing fires. Traditional approaches have often employed the analysis of weather observations and forecasts to determine whether a prescribed burn will affect populations,more » property, or protected Class I areas. However, the complexity of the problem lends itself to advanced PC-based models that are simple to use for both calculating the emissions from the burning of wildland fuels and the downwind dispersion of smoke and other products of pyrolysis, distillation, and/or fuels combustion. These models will need to address the effects of residual smoldering combustion, including plume dynamics and optical effects. In this paper, we discuss a suite of tools that can be applied for analyzing dispersion. These tools include the dispersion models FIREPLUME and SMOKE, together with the meteorological preprocessor SEBMET.« less

Ensemble modeling to predict habitat suitability for a large-scale disturbance specialist

PubMed Central

Latif, Quresh S; Saab, Victoria A; Dudley, Jonathan G; Hollenbeck, Jeff P

2013-01-01

To conserve habitat for disturbance specialist species, ecologists must identify where individuals will likely settle in newly disturbed areas. Habitat suitability models can predict which sites at new disturbances will most likely attract specialists. Without validation data from newly disturbed areas, however, the best approach for maximizing predictive accuracy can be unclear (Northwestern U.S.A.). We predicted habitat suitability for nesting Black-backed Woodpeckers (Picoides arcticus; a burned-forest specialist) at 20 recently (≤6 years postwildfire) burned locations in Montana using models calibrated with data from three locations in Washington, Oregon, and Idaho. We developed 8 models using three techniques (weighted logistic regression, Maxent, and Mahalanobis D2 models) and various combinations of four environmental variables describing burn severity, the north–south orientation of topographic slope, and prefire canopy cover. After translating model predictions into binary classifications (0 = low suitability to unsuitable, 1 = high to moderate suitability), we compiled “ensemble predictions,” consisting of the number of models (0–8) predicting any given site as highly suitable. The suitability status for 40% of the area burned by eastside Montana wildfires was consistent across models and therefore robust to uncertainty in the relative accuracy of particular models and in alternative ecological hypotheses they described. Ensemble predictions exhibited two desirable properties: (1) a positive relationship with apparent rates of nest occurrence at calibration locations and (2) declining model agreement outside surveyed environments consistent with our reduced confidence in novel (i.e., “no-analogue”) environments. Areas of disagreement among models suggested where future surveys could help validate and refine models for an improved understanding of Black-backed Woodpecker nesting habitat relationships. Ensemble predictions presented here can help guide managers attempting to balance salvage logging with habitat conservation in burned-forest landscapes where black-backed woodpecker nest location data are not immediately available. Ensemble modeling represents a promising tool for guiding conservation of large-scale disturbance specialists. PMID:24340177

Solid-propellant rocket motor internal ballistics performance variation analysis, phase 5

NASA Technical Reports Server (NTRS)

Sforzini, R. H.; Murph, J. E.

1980-01-01

The results of research aimed at improving the predictability of internal ballistics performance of solid-propellant rocket motors (SRM's) including thrust imbalance between two SRM's firing in parallel are presented. Static test data from the first six Space Shuttle SRM's is analyzed using a computer program previously developed for this purpose. The program permits intentional minor design biases affecting the imbalance between any two SMR's to be removed. Results for the last four of the six SRM's, with only the propellant bulk temperature as a non-random variable, are generally within limits predicted by theory. Extended studies of internal ballistic performance of single SRM's are presented based on an earlier developed mathematical model which includes an assessment of grain deformation. The erosive burning rate law used in the model is upgraded and made more general. Excellent results are obtained in predictions of the performances of five different SRM's of quite different sizes and configurations. These SRM's all employ PBAN type propellants with ammonium perchlorate oxidizer and 16 to 20% aluminum except one which uses carboxyl terminated butadiene binder. The only non-calculated parameters in the burning rate equations that are changed for the different SRM's are the zero crossflow velocity burning rate coefficients and exponents. The results, in general, confirm the importance of grain deformation. The improved internal ballistic model makes practical development of an effective computer program for application of an optimization technique to SRM design which is also demonstrated. The program uses a pattern search technique to minimize the difference between a desired thrust-time trace and one calculated based on the internal ballistic model.

Experimental and Numerical Study of Ammonium Perchlorate Counterflow Diffusion Flames

NASA Technical Reports Server (NTRS)

Smooke, M. D.; Yetter, R. A.; Parr, T. P.; Hanson-Parr, D. M.; Tanoff, M. A.

1999-01-01

Many solid rocket propellants are based on a composite mixture of ammonium perchlorate (AP) oxidizer and polymeric binder fuels. In these propellants, complex three-dimensional diffusion flame structures between the AP and binder decomposition products, dependent upon the length scales of the heterogeneous mixture, drive the combustion via heat transfer back to the surface. Changing the AP crystal size changes the burn rate of such propellants. Large AP crystals are governed by the cooler AP self-deflagration flame and burn slowly, while small AP crystals are governed more by the hot diffusion flame with the binder and burn faster. This allows control of composite propellant ballistic properties via particle size variation. Previous measurements on these diffusion flames in the planar two-dimensional sandwich configuration yielded insight into controlling flame structure, but there are several drawbacks that make comparison with modeling difficult. First, the flames are two-dimensional and this makes modeling much more complex computationally than with one-dimensional problems, such as RDX self- and laser-supported deflagration. In addition, little is known about the nature, concentration, and evolution rates of the gaseous chemical species produced by the various binders as they decompose. This makes comparison with models quite difficult. Alternatively, counterflow flames provide an excellent geometric configuration within which AP/binder diffusion flames can be studied both experimentally and computationally.

Analysis of the burns profile and the admission rate of severely burned adult patient to the National Burn Center of Chile after the 2010 earthquake.

PubMed

Albornoz, Claudia; Villegas, Jorge; Sylvester, Marilu; Peña, Veronica; Bravo, Iside

2011-06-01

Chile is located in the Ring of Fire, in South America. An earthquake 8.8° affected 80% of the population in February 27th, 2010. This study was conducted to assess any change in burns profile caused by the earthquake. This was an ecologic study. We compared the 4 months following the earthquake in 2009 and 2010. age, TBSA, deep TBSA, agent, specific mortality rate and rate of admissions to the National burn Center of Chile. Mann-Whitney test and a Poisson regression were performed. Age, agent, TBSA and deep TBSA percentages did not show any difference. Mortality rate was lower in 2010 (0.52 versus 1.22 per 1,000,000 habitants) but no meaningful difference was found (Poisson regression p = 0.06). Admission rate was lower in 2010, 4.6 versus 5.6 per 1,000,000 habitants, but no differences were found (p = 0.26). There was not any admissions directly related to the earthquake. As we do not have incidence registries in Chile, we propose to use the rate of admission to the National Burn Reference Center as an incidence estimator. There was not any significant difference in the burn profile, probably because of the time of the earthquake (3 am). We conclude the earthquake did not affect the way the Chilean people get burned. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

Modeling the effects of vegetation heterogeneity on wildland fire behavior

NASA Astrophysics Data System (ADS)

Atchley, A. L.; Linn, R.; Sieg, C.; Middleton, R. S.

2017-12-01

Vegetation structure and densities are known to drive fire-spread rate and burn severity. Many fire-spread models incorporate an average, homogenous fuel density in the model domain to drive fire behavior. However, vegetation communities are rarely homogenous and instead present significant heterogeneous structure and fuel densities in the fires path. This results in observed patches of varied burn severities and mosaics of disturbed conditions that affect ecological recovery and hydrologic response. Consequently, to understand the interactions of fire and ecosystem functions, representations of spatially heterogeneous conditions need to be incorporated into fire models. Mechanistic models of fire disturbance offer insight into how fuel load characterization and distribution result in varied fire behavior. Here we use a physically-based 3D combustion model—FIRETEC—that solves conservation of mass, momentum, energy, and chemical species to compare fire behavior on homogenous representations to a heterogeneous vegetation distribution. Results demonstrate the impact vegetation heterogeneity has on the spread rate, intensity, and extent of simulated wildfires thus providing valuable insight in predicted wildland fire evolution and enhanced ability to estimate wildland fire inputs into regional and global climate models.

Thermal design and analysis of a hydrogen-burning wind tunnel model of an airframe-integrated scramjet

NASA Technical Reports Server (NTRS)

Guy, R. W.; Mueller, J. N.; Pinckney, S. Z.; Lee, L. P.

1976-01-01

An aerodynamic model of a hydrogen burning, airframe integrated scramjet engine has been designed, fabricated, and instrumented. This model is to be tested in an electric arc heated wind tunnel at an altitude of 35.39 km (116,094 ft.) but with an inlet Mach number of 6 simulating precompression on an aircraft undersurface. The scramjet model is constructed from oxygen free, high conductivity copper and is a heat sink design except for water cooling in some critical locations. The model is instrumented for pressure, surface temperature, heat transfer rate, and thrust measurements. Calculated flow properties, heat transfer rates, and surface temperature distributions along the various engine components are included for the conditions stated above. For some components, estimates of thermal strain are presented which indicate significant reductions in plastic strain by selective cooling of the model. These results show that the 100 thermal cycle life of the engine was met with minimum distortion while staying within the 2669 N (600 lbf) engine weight limitation and while cooling the engine only in critical locations.

New perspectives on quantitative characterization of biomass burning (Invited)

NASA Astrophysics Data System (ADS)

Ichoku, C. M.

2010-12-01

Biomass burning (BB) occurs seasonally in different vegetated landscapes across the world, consuming large amounts of biomass, generating intense heat energy, and emitting corresponding amounts of smoke plumes that comprise aerosols and trace gases, which include carbon monoxide (CO), carbon dioxide (CO2), methane (CH4), non-methane hydrocarbons, and numerous other trace compounds, many of which have adverse effects on human health, air quality, and environmental processes. Accurate estimates of these emissions are required as model inputs to evaluate and forecast smoke plume transport and impacts on air quality, human health, clouds, weather, radiation, and climate. The goal of this presentation is to highlight results of research activities that are aimed at advancing the quantitative characterization of various aspects of biomass burning (energetics, intensity, burn areas, burn severity, emissions, and fire weather) from aircraft and satellite measurements that can help advance our understanding of biomass burning and its overall effects. We will show recent results of analysis of fire radiative power (FRP), burned areas, fuel consumption, smoke emission rates, and plume heights from satellite measurements, as well as related aircraft calibration/validation activities. We will also briefly examine potential future plans and strategies for effective monitoring of biomass burning characteristics and emissions from aircraft and satellite.

Evolutionary sequences of very hot, low-mass, accreting white dwarfs with application to symbiotic variables and ultrasoft/supersoft low-luminosity x-ray sources

NASA Technical Reports Server (NTRS)

Sion, Edward M.; Starrfield, Sumner G.

1994-01-01

We present the first detailed model results of quasi-static evolutionary sequences of very hot low-mass white dwarfs accreting hydrogen-rich material at rates between 1 x 10(exp -7) and 1 x 10(exp -9) solar mass/yr. Most of the sequences were generated from starting models whose core thermal structures were not thermally relaxed in the thermal pulse cycle-averaged sense of an asymptotic giant branch stellar core. Hence, the evolution at constant accretion rate was not invariably characterized by series of identical shell flashes. Sequences exhibiting stable steady state nuclear burning at the accretion supply rate as well as sequences exhibiting recurrent thermonuclear shell flashes are presented and discussed. In some cases, the white dwarf accretors remain small (less than 10(exp 11) cm) and very hot even during the shell flash episode. They then experience continued but reduced hydrogen shell burning during the longer quiescent intervals while their surface temperatures increase both because of compressional heating and envelope structure readjustment in response to accretion over thousands of years. Both accretion and continued hydrogen burning power these models with luminosities of a few times 10(exp 37) ergs/s. We suggest that the physical properties of these model sequences are of considerable relevance to the observed outburst and quiescent behavior of those symbiotic variables and symbiotic novae containing low-mass white dwarfs. We also suggest that our models are relevant to the observational characteristics of the growing class of low-luminosity, supersoft/ultrasoft X-ray sources in globular clusters, and the Magellanic Clouds.

The effects of epidermal debridement of partial-thickness burns on infection and reepithelialization in swine.

PubMed

Singer, A J; Thode, H C; McClain, S A

2000-02-01

Early postburn debridement of burn blisters is controversial. This study was conducted to compare rates of infection and reepithelialization in debrided vs nondebrided second-degree burns in swine. This was a prospective, blinded, controlled, experimental trial using isoflurane-anesthetized swine. Standardized partial-thickness burns were inflicted by applying an aluminum bar preheated to 80 degrees C to the backs and flanks of two young pigs for 20 seconds. In half of the burns the necrotic epidermis was manually debrided. All burns were randomly treated with octylcyanoacrylate spray (OCA) or dry gauze (C). Full-thickness biopsies were taken at 7, 10, and 14 days for blinded histopathologic evaluation. The primary outcomes were the proportions of infected burns at days 7 and 10 and the proportion of completely reepithelialized burns at day 14. Burns were considered infected in the presence of intradermal neutrophils containing bacteria (intraobserver agreement, K = 1.00). A secondary outcome was the proportion of burns with the presence of scar tissue (abnormal collagen under polarized light; intraobserver correlation, K = 0.93). Chi-square tests were used for group comparisons. This study had 90% power to detect a 40-percentage-point difference in infection rates (alpha = 0.05). A total of 126 biopsies from 42 burns were available for review. Infection rates were higher in the debrided burns both at day 7 (55% vs 4.5%, p < 0.001) and at day 10 (65% vs 9%, p < 0.001) after injury. The proportion of nondebrided burns that were completely reepithelialized was higher at days 10 (68% vs 0%, p < 0.001) and 14 (100% vs 65%, p = 0.003). The presence of scar tissue was more common in debrided burns (75% vs 4.5%, p < 0.001). Burns treated with OCA had fewer infections than controls (4% vs 55%, p < 0.001). Fewer OCA-treated debrided burns were reepithelialized at 14 days than those that were not debrided (30% vs 100%, p = 0.001). Under the current study conditions, early postburn epidermal debridement of second-degree burns resulted in more infections and slower reepithelialization rates in swine. The effects of early postburn epidermal debridement in humans should be explored.

The organisation of critical care for burn patients in the UK: epidemiology and comparison of mortality prediction models.

PubMed

Toft-Petersen, A P; Ferrando-Vivas, P; Harrison, D A; Dunn, K; Rowan, K M

2018-05-15

In the UK, a network of specialist centres has been set up to provide critical care for burn patients. However, some burn patients are admitted to general intensive care units. Little is known about the casemix of these patients and how it compares with patients in specialist burn centres. It is not known whether burn-specific or generic risk prediction models perform better when applied to patients managed in intensive care units. We examined admissions for burns in the Case Mix Programme Database from April 2010 to March 2016. The casemix, activity and outcome in general and specialist burn intensive care units were compared and the fit of two burn-specific risk prediction models (revised Baux and Belgian Outcome in Burn Injury models) and one generic model (Intensive Care National Audit and Research Centre model) were compared. Patients in burn intensive care units had more extensive injuries compared with patients in general intensive care units (median (IQR [range]) burn surface area 16 (7-32 [0-98])% vs. 8 (1-18 [0-100])%, respectively) but in-hospital mortality was similar (22.8% vs. 19.0%, respectively). The discrimination and calibration of the generic Intensive Care National Audit and Research Centre model was superior to the revised Baux and Belgian Outcome in Burn Injury burn-specific models for patients managed on both specialist burn and general intensive care units. © 2018 The Association of Anaesthetists of Great Britain and Ireland.

Design and testing of digitally manufactured paraffin Acrylonitrile-butadiene-styrene hybrid rocket motors

NASA Astrophysics Data System (ADS)

McCulley, Jonathan M.

This research investigates the application of additive manufacturing techniques for fabricating hybrid rocket fuel grains composed of porous Acrylonitrile-butadiene-styrene impregnated with paraffin wax. The digitally manufactured ABS substrate provides mechanical support for the paraffin fuel material and serves as an additional fuel component. The embedded paraffin provides an enhanced fuel regression rate while having no detrimental effect on the thermodynamic burn properties of the fuel grain. Multiple fuel grains with various ABS-to-Paraffin mass ratios were fabricated and burned with nitrous oxide. Analytical predictions for end-to-end motor performance and fuel regression are compared against static test results. Baseline fuel grain regression calculations use an enthalpy balance energy analysis with the material and thermodynamic properties based on the mean paraffin/ABS mass fractions within the fuel grain. In support of these analytical comparisons, a novel method for propagating the fuel port burn surface was developed. In this modeling approach the fuel cross section grid is modeled as an image with white pixels representing the fuel and black pixels representing empty or burned grid cells.

Joint Aircraft Survivability Program Final Test Report for the Acoustic Fire Suppression Project JASP-TR-14-05

DTIC Science & Technology

2016-09-01

focus of early research was the effects of acoustics on droplet burning in turbine engines and combustion chambers.5,21–23 The results of this... Wire Anemometer. Time-resolved mass readings were made using a model MS4002S Mettler Toledo Precision Balance. 5. Acoustic Extinction This section...nanotube sound projectors. Nanotechnology. 2013;24(23):235501. 40. Hu L, Liu S, Xu Y, Li D. A wind tunnel experimental study on burning rate

Estimates of global biomass burning emissions for reactive greenhouse gases (CO, NMHCs, and NOx) and CO2

NASA Astrophysics Data System (ADS)

Jain, Atul K.; Tao, Zhining; Yang, Xiaojuan; Gillespie, Conor

2006-03-01

Open fire biomass burning and domestic biofuel burning (e.g., cooking, heating, and charcoal making) algorithms have been incorporated into a terrestrial ecosystem model to estimate CO2 and key reactive GHGs (CO, NOx, and NMHCs) emissions for the year 2000. The emissions are calculated over the globe at a 0.5° × 0.5° spatial resolution using tree density imagery, and two separate sets of data each for global area burned and land clearing for croplands, along with biofuel consumption rate data. The estimated global and annual total dry matter (DM) burned due to open fire biomass burning ranges between 5221 and 7346 Tg DM/yr, whereas the resultant emissions ranges are 6564-9093 Tg CO2/yr, 438-568 Tg CO/yr, 11-16 Tg NOx/yr (as NO), and 29-40 Tg NMHCs/yr. The results indicate that land use changes for cropland is one of the major sources of biomass burning, which amounts to 25-27% (CO2), 25 -28% (CO), 20-23% (NO), and 28-30% (NMHCs) of the total open fire biomass burning emissions of these gases. Estimated DM burned associated with domestic biofuel burning is 3,114 Tg DM/yr, and resultant emissions are 4825 Tg CO2/yr, 243 Tg CO/yr, 3 Tg NOx/yr, and 23 Tg NMHCs/yr. Total emissions from biomass burning are highest in tropical regions (Asia, America, and Africa), where we identify important contributions from primary forest cutting for croplands and domestic biofuel burning.

Combined ionizing radiation and thermal injury in the rat. Evaluation of early excision and closure of the burn wound

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirsch, E.F.; Vezina, R.; Corbett, S.

1990-01-01

The present study was undertaken to establish an animal model of combined whole-body irradiation and thermal injury and to determine the effectiveness of early excision and closure of the burn wound in such a model. Whole-body irradiation over a range of doses resulted in a predictable mortality rate, with an LD50/30 of 783 rad with 95% confidence limits of 737 and 823 rad. A controlled 10% body surface area full-thickness thermal injury resulted in no deaths in 30 animals. When combined with a standard nonlethal 10% thermal injury, varying doses of whole-body irradiation resulted in widely differing LD50/30 values inmore » three separate cohorts of rats. Excision and closure of a 10% burn 24 hours after exposure to 200 rads did not improve survival.« less

Addendum to High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Tan, N

2010-11-08

As part of a small follow-on study, the burn rate of the ammonium perchlorate (AP) based material TAL-1503 was studied at a relatively mild pressure. The goal of this final experiment was to burn TAL-1503 at the lowest pressures possible using the LLNL High Pressure Strand Burner (LLNL-HPSB). The following is a description of the experiment and the results with a brief discussion of data and a comparison to the higher pressure data. This is not meant to be a stand-alone report and readers should refer to the main report for experimental details and discussion. High pressure deflagration rate measurementsmore » of a unique AP/HTPB based material (TAL-1503) were performed using the LLNL high pressure strand burner apparatus. The material burns in a well behaved, laminar fashion between 20 and 300 MPa with a burn law of B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} that was calculated based on the best data available from the experiments. In the pressure range of 2 and 10 MPa the material burned laminarly with a burn law of B = (2.0 {+-} 0.2) x P{sup (0.66{+-}0.05)}. In these results, B is the burn rate in mm/s and P is the pressure in units of MPa. Comparison of the TAL-1503 results with similar propellants that contain micrometer sized aluminum indicate that the burn rates are relatively unaffected by the aluminum. However, the pressure change is significantly larger when aluminum is present, most likely due to the high temperatures achieved from burning aluminum.« less

Two Dimensional Heat Transfer in Non-Thermally Thin Poly(Methyl Methacrylate) During Combustion in a Narrow Channel Apparatus

NASA Astrophysics Data System (ADS)

Lage, Nicholas Alexander

Experimentation and Computational modeling of non-thermally thin samples of poly(methyl methacrylate) (PMMA) burning in a Narrow Channel Apparatus (NCA) was conducted. The Narrow Channel Apparatus is used to replicate a microgravity environment by flowing of mixtures of nitrogen and oxygen through a narrow gap to suppress buoyancy above the burning sample. A new NCA was built, and experiments were conducted using it to provide the empirical data presented in this thesis. Samples of PMMA were burned, with thicknesses of 3, 5, and 10 mm, with an opposed-flow mean velocity of 15 cm/s and a 21% oxygen concentration. Flame spread rates were obtained from tracked flame positions. Thermocouples were embedded in the top and bottom surfaces of some of the samples to measure surface temperatures. Using Fire Dynamics Simulator (FDS), version 6.2.0, coupled with Gpyro, a two-dimensional model was developed for non-thermally thin samples of PMMA that are burned in the NCA. A 5 mm gap height was used as well as a laminar, parabolic flow at the inlet. Direct numerical simulation (DNS) was set. Finite rate kinetics were used to model the pyrolysis and combustion reactions. Complete combustion was assumed. Simulations with fuel thicknesses of 1, 3, 5, and 10 mm were run, under the same conditions as the experiment. A comparison between one-dimensional and two-dimensional heat conduction within the sample was made to show the effect the heat transfer parallel to flame propagation has on flame spread rates and solid-phase temperature profiles. A comparison between mica and an adiabatic plane set beneath the PMMA was also made as well as the length of time the sample is exposed to the ignition source. Through comparison of the model with the experiment, it was found that the flame spread rates of the model showed unrealistic trends with thickness. An investigation was completed with the aid of an energy balance as well as graphs, such as equivalence ratios, surface temperatures, surface heat fluxes, fuel vapor mass fluxes, etc., that were plotted with respect to the flame position to find the source of the unrealistic trends, but conclusive evidence was never obtained.

Evaluation of Additives to Reduce Solid Propellant Flammability in Ambient Air.

DTIC Science & Technology

1975-12-01

been applied successfully to reduce the flammability of plastics and polymers. From that experimental data base, the following have been shown to be...consumption rate of the cube) are reported since they are more repeatable than the linear burning rate data . B. Free Convection Effects Several series of...Steady State Burning Rate Measurements Obtaining steady state burning rate data in air requires a technique for holding the characteristic length

Efficacy of moist exposed burn ointment on burns.

PubMed

Zhang, Hong-Qi; Yip, Tsui-Pik; Hui, Irene; Lai, Vincy; Wong, Ann

2005-01-01

In this study, we sought to test the medical efficacy of a Chinese medical herb product, moist exposed burn ointment (MEBO), on wound healing rate and infection control in burn injury. Standardized deep burn wounds were created on the back skin of rats by applying a hot brass bar for 12 to 18 seconds. MEBO was applied four times per day and compared with petroleum jelly, silver sulfadiazine, and dry exposure therapy. Under such a controlled setting, although MEBO had a better wound healing rate than the dry exposure treatment, it did not show the medical advantage statistically, as has been claimed, over the other two treatments (P > .05), either in terms of wound healing rate or bacterial control. We conclude that the MEBO is not suitable for deep burn wound treatment, particularly when infection is a concern.

Burn-related factors affecting anxiety, depression and self-esteem in burn patients: an exploratory study.

PubMed

Jain, M; Khadilkar, N; De Sousa, A

2017-03-31

Burns are physically, psychologically and economically challenging injuries, and the factors leading to them are many and under-studied. The aim of the current study was to assess level of anxiety, depression and self-esteem in burn patients, and look at various burn-related variables that affect them. This cross-sectional study included 100 patients with burn injuries admitted to a tertiary care private hospital in an urban metropolis in India. The patients were assessed for anxiety, depression and self-esteem using the Hamilton anxiety rating scale, Hamilton depression rating scale and Rosenberg self-esteem scale respectively. Assessment was carried out within 2-8 weeks of injury following medical stabilization. The data was tabulated and statistically analyzed. The study sample was predominantly male (54%), married (69%), with a mean age of 34.1 ± 10.8 years. Accidental burns (94%) were the most common modality of injury. The majority (46%) suffered burns involving 20-59% total body surface area (TBSA), and facial burns were present (57%). No significant association was found between TBSA and anxiety, depression or self-esteem, and the same was true for facial burns. Deep burns, however, were significantly associated with anxiety (p=0.03) and depression (p=0.0002). High rates of anxiety and depression are associated with burn injuries and related to burn depth. Adjustment and recovery in these patients depends on various other factors like the patient's psychological status, nature/extent of the injury and ensuing medical care. Further research is warranted to reveal the magnitude and predictors of psychological problems in burn patients.

Combustion of Methane Hydrate

NASA Astrophysics Data System (ADS)

Roshandell, Melika

A significant methane storehouse is in the form of methane hydrates on the sea floor and in the arctic permafrost. Methane hydrates are ice-like structures composed of water cages housing a guest methane molecule. This caged methane represents a resource of energy and a potential source of strong greenhouse gas. Most research related to methane hydrates has been focused on their formation and dissociation because they can form solid plugs that complicate transport of oil and gas in pipelines. This dissertation explores the direct burning of these methane hydrates where heat from the combustion process dissociates the hydrate into water and methane, and the released methane fuels the methane/air diffusion flame heat source. In contrast to the pipeline applications, very little research has been done on the combustion and burning characteristics of methane hydrates. This is the first dissertation on this subject. In this study, energy release and combustion characteristics of methane hydrates were investigated both theoretically and experimentally. The experimental study involved collaboration with another research group, particularly in the creation of methane hydrate samples. The experiments were difficult because hydrates form at high pressure within a narrow temperature range. The process can be slow and the resulting hydrate can have somewhat variable properties (e.g., extent of clathration, shape, compactness). The experimental study examined broad characteristics of hydrate combustion, including flame appearance, burning time, conditions leading to flame extinguishment, the amount of hydrate water melted versus evaporated, and flame temperature. These properties were observed for samples of different physical size. Hydrate formation is a very slow process with pure water and methane. The addition of small amounts of surfactant increased substantially the hydrate formation rate. The effects of surfactant on burning characteristics were also studied. One finding from the experimental component of the research was that hydrates can burn completely, and that they burn most rapidly just after ignition and then burn steadily when some of the water in the dissociated zone is allowed to drain away. Excessive surfactant in the water creates a foam layer around the hydrate that acts as an insulator. The layer prevents sufficient heat flux from reaching the hydrate surface below the foam to release additional methane and the hydrate flame extinguishes. No self-healing or ice-freezing processes were observed in any of the combustion experiments. There is some variability, but a typical hydrate flame is receiving between one and two moles of water vapor from the liquid dissociated zone of the hydrate for each mole of methane it receives from the dissociating solid region. This limits the flame temperature to approximately 1800 K. In the theoretical portion of the study, a physical model using an energy balance from methane combustion was developed to understand the energy transfer between the three phases of gas, liquid and solid during the hydrate burn. Also this study provides an understanding of the different factors impacting the hydrate's continuous burn, such as the amount of water vapor in the flame. The theoretical study revealed how the water layer thickness on the hydrate surface, and its effect on the temperature gradient through the dissociated zone, plays a significant role in the hydrate dissociation rate and methane release rate. Motivated by the above mentioned observation from the theoretical analysis, a 1-D two-phase numerical simulation based on a moving front model for hydrate dissociation from a thermal source was developed. This model was focused on the dynamic growth of the dissociated zone and its effect on the dissociation rate. The model indicated that the rate of hydrate dissociation with a thermal source is a function of the dissociated zone thickness. It shows that in order for a continuous dissociation and methane release, some of the water from the dissociated zone needs to be drained. The results are consistent with the experimental observations. The understanding derived from the experiments and the numerical model permitted a brief exploration into the potential effects of pressure on the combustion of methane hydrates. The prediction is that combustion should improve under high pressure conditions because the evaporation of water is suppressed allowing more energy into the dissociation. Future experiments are needed to validate these initial findings.

Experimental study on burning rates of square/rectangular gasoline and methanol pool fires under longitudinal air flow in a wind tunnel.

PubMed

Hu, L H; Liu, S; Peng, W; Huo, R

2009-09-30

Square pool fires with length of 5, 7.5, 10, 15, 20, 25 and 30 cm and rectangular pool fires with dimensions of 10 cm x 20 cm and 10 cm x 40 cm were burned in a wind tunnel, under a longitudinal air flow ranged from 0 to 3m/s with incremental change of about 0.5m/s. Methanol and gasoline were burned and compared, with results indicated that their burning rates showed different response to the longitudinal air flow. With the increase of the longitudinal air flow speed, the burning rates of methanol pool fires, except the 5 cm square one, first decreased and then increased, but those of the 5 cm methanol square one and the gasoline pool fires increased monotonously. The burning rate of smaller square pool fires increased more significantly than that of the larger ones, as well as the enlargement of their flame attachment length along the ground. The burning rate of a rectangular pool fire with longer rim parallel to the longitudinal flow increased faster, but the flame attachment length seemed to increase more gradually, with the increase of the longitudinal air flow speed than that perpendicular to.

Inclusion of biomass burning in WRF-Chem: Impact of wildfires on weather forecasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grell, G. A.; Freitas, Saulo; Stuefer, Martin

2011-06-06

A plume rise algorithm for wildfires was included in WRF-Chem, and applied to look at the impact of intense wildfires during the 2004 Alaska wildfire season on weather forecasts using model resolutions of 10km and 2km. Biomass burning emissions were estimated using a biomass burning emissions model. In addition, a 1-D, time-dependent cloud model was used online in WRF-Chem to estimate injection heights as well as the final emission rates. It was shown that with the inclusion of the intense wildfires of the 2004 fire season in the model simulations, the interaction of the aerosols with the atmospheric radiation ledmore » to significant modifications of vertical profiles of temperature and moisture in cloud-free areas. On the other hand, when clouds were present, the high concentrations of fine aerosol (PM2.5) and the resulting large numbers of Cloud Condensation Nuclei (CCN) had a strong impact on clouds and microphysics, with decreased precipitation coverage and precipitation amounts during the first 12 hours of the integration, but significantly stronger storms during the afternoon hours.« less

Mathematical model of a smoldering log.

Treesearch

Fernando de Souza Costa; David Sandberg

2004-01-01

A mathematical model is developed describing the natural smoldering of logs. It is considered the steady one dimensional propagation of infinitesimally thin fronts of drying, pyrolysis, and char oxidation in a horizontal semi-infinite log. Expressions for the burn rates, distribution profiles of temperature, and positions of the drying, pyrolysis, and smoldering fronts...

Improved survival with an innovative approach to the treatment of severely burned patients: development of a burn treatment manual.

PubMed

Morisada, S; Nosaka, N; Tsukahara, K; Ugawa, T; Sato, K; Ujike, Y

2015-09-30

The management of severely burned patients remains a major issue worldwide as indicated by the high incidence of permanent debilitating complications and poor survival rates. In April 2012, the Advanced Emergency & Critical Care Medical Center of the Okayama University Hospital began implementing guidelines for severely burned patients, distributed as a standard burn treatment manual. The protocol, developed in-house, was validated by comparing the outcomes of patients with severe extensive burns (SEB) treated before and after implementation of these new guidelines at this institution. The patients included in this study had a burn index (BI) ≥30 or a prognostic burn index (PBI = BI + patient's age) ≥100. The survival rate of the patients with BI ≥30 was 65.2% with the traditional treatment and 100% with the new guidelines. Likewise, the survival rate of the patients with PBI ≥100 was 61.1% with the traditional treatment compared to 100% with the new guidelines. Together, these data demonstrate that the new treatment guidelines dramatically improved the treatment outcome and survival of SEB patients.

Burn care in South Africa: a micro cosmos of Africa.

PubMed

Rode, H; Cox, S G; Numanoglu, A; Berg, A M

2014-07-01

Burn injuries in Africa are common with between 300,000 and 17.5 million children under 5 years sustaining burn injuries annually, resulting in a high estimated fatality rate. These burns are largely environmentally conditioned and therefore preventable. The Western Cape Province in South Africa can be regarded as a prototype of paediatric burns seen on the continent, with large numbers, high morbidity and mortality rates and an area inclusive of all factors contributing to this extraordinary burden of injury. Most of the mechanisms to prevent burns are not easily modified due to the restraint of low socio-economic homes, overcrowding, unsafe appliances, multiple and complex daily demands on families and multiple psycho-social stressors. Children <4 years are at highest risk of burns with an average annual rate of 6.0/10,000 child-years. Burn care in South Africa is predominantly emergency driven and variable in terms of organization, clinical management, facilities and staffing. Various treatment strategies were introduced. The management of HIV positive children poses a problem, as well as the conflict of achieving equity of burn care for all children. Without alleviating poverty, developing minimum standards for housing, burn education, safe appliances and legislation, we will not be able to reduce the "curse of poor people" and will continue to treat the consequences.

Mechanistic approach for nitride fuel evolution and fission product release under irradiation

NASA Astrophysics Data System (ADS)

Dolgodvorov, A. P.; Ozrin, V. D.

2017-01-01

A model for describing uranium-plutonium mixed nitride fuel pellet burning was developed. Except fission products generating, the model includes impurities of oxygen and carbon. Nitrogen behaviour in nitride fuel was analysed and the nitrogen chemical potential in solid solution with uranium-plutonium nitride was constructed. The chemical program module was tested with the help of thermodynamic equilibrium phase distribution calculation. Results were compared with analogous data in literature, quite good agreement was achieved, especially for uranium sesquinitride, metallic species and some oxides. Calculation of a process of nitride fuel burning was also conducted. Used mechanistic approaches for fission product evolution give the opportunity to find fission gas release fractions and also volumes of intergranular secondary phases. Calculations present that the most massive secondary phases are the oxide and metallic phases. Oxide phase contain approximately 1 % wt of substance over all time of burning with slightly increasing of content. Metallic phase has considerable rising of mass and by the last stage of burning it contains about 0.6 % wt of substance. Intermetallic phase has less increasing rate than metallic phase and include from 0.1 to 0.2 % wt over all time of burning. The highest element fractions of released gaseous fission products correspond to caesium and iodide.

Air Quality Impact from Biomass Burning in Northern Sub-Saharan Africa (NSSA).

NASA Astrophysics Data System (ADS)

Damoah, R.; Ichoku, C. M.; Ellison, L.

2016-12-01

Biomass burning (BB) is one of the major sources of troposheric ozone (O3) precursors such as nitrogen oxides (NOx), carbon monoxides (CO), and non-methane volatile organics compounds (NMVOCs) as well as primary aerosols such as organic carbon (OC) and black carbon (BC). These emissions do not only affect air quality locally, but also on continental to hemispheric scales through long-range transport. It is estimated that about 350 Million hectares of land burn globally every year of which 54 % are in Africa. The northern sub-Saharan African (NSSA) region (0 - 20N, 20W - 55E) is known to show one of the highest biomass burning rates (in terms of per unit land area) among all regions of the world. This is due to the high concentration and frequency of fires in this region. In 2016 a newly installed AERONET ( ) sun photometer at All Nations University College (6.2N, 0.3W) within our study region recorded enhanced aerosol optical depth presume to be triggered by smoke from fires. We will discuss sources of this enhancement as well results obtained from NASA's Global Modeling Initiative Chemistry and Transport Model (GMI-CTM), to quantify the impact on air quality by biomass burning.

Theoretical evaluation of burns to the human respiratory tract due to inhalation of hot gas in the early stage of fires.

PubMed

Lv, Yong-Gang; Liu, Jing; Zhang, Jun

2006-06-01

A transient two-dimensional mathematical model for heat and water vapor transport across the respiratory tract of human body was established and applied to predict the thermal impact of inhaled hot gas to the nasal tissues during the early stage of fires. Influences of individual's physiological status and environment variables were comprehensively investigated through numerical calculations. Burn evaluation was performed using the classical Henriques model to predict the time for thermal injury to occur. It was shown that decreasing the air velocity and increasing the respiratory rate is helpful to minimize the burn over the respiratory tract. The effect of relative humidity of surrounding dry hot air could be ignored in predicting burns for short duration exposures. Due to evaporation cooling on the mucousal membrane, the burn often occurs at certain positions underneath the skin of the tract near the inlet of the respiratory tract. Most of the tissues near the surface suffer injury immediately after exposure to fire, while in the deeper tissues, serious damage occurs after a relatively longer time period. The method presented in this paper may suggest a valuable approach to theoretically evaluate the injury of hot air to the human respiratory tract under various fire situations.

Mother, father and child traumatic stress reactions after paediatric burn: Within-family co-occurrence and parent-child discrepancies in appraisals of child stress.

PubMed

Egberts, Marthe R; van de Schoot, Rens; Geenen, Rinie; Van Loey, Nancy E E

2018-06-01

The current study examined occurrence and within-family associations of traumatic stress reactions after child burn injury, while in the same model addressing the role of parents' own symptoms in their reports of child symptoms. One-hundred children (8-18 years old), and their mothers (n=90) and fathers (n=74) were assessed within the first month (T1) and three months (T2) after burn. Parents and children rated child traumatic stress reactions on the Children's Responses to Trauma Inventory (CRTI) and parents rated their own reactions on the Impact of Event Scale (IES). Cross-sectional associations at the two occasions were examined using a structural equation model. Occurrence of traumatic stress symptoms in the clinical range was higher in parents (T1: 24-50%; T2: 14-31%) than children (T1: 0-11%; T2: 3-5%, depending on whether children, mothers or fathers reported on symptoms). Traumatic stress symptoms of mothers at T1 and of both parents at T2 were significantly related to child self-reported symptoms. Moreover, mothers who experienced higher stress symptoms themselves gave higher ratings of their child's symptoms at both time points, while for fathers, this was only found at T2. The current study demonstrates the impact of pediatric burn injury on the family level, and shows simultaneous existence of within-family interrelatedness of traumatic stress and an influence of parents' own symptoms on their perception of child symptoms. Findings highlight the need for trauma symptom screening in all family members and for considering informants' symptoms to understand the child's functioning in particular. Copyright © 2018 Elsevier Ltd and ISBI. All rights reserved.

Accelerant-related burns and drug abuse: Challenging combination.

PubMed

Leung, Leslie T F; Papp, Anthony

2018-05-01

Accelerants are flammable substances that may cause explosion when added to existing fires. The relationships between drug abuse and accelerant-related burns are not well elucidated in the literature. Of these burns, a portion is related to drug manufacturing, which have been shown to be associated with increased burn complications. 1) To evaluate the demographics and clinical outcomes of accelerant-related burns in a Provincial Burn Centre. 2) To compare the clinical outcomes with a control group of non-accelerant related burns. 3) To analyze a subgroup of patients with history of drug abuse and drug manufacturing. Retrospective case control study. Patient data associated with accelerant-related burns from 2009 to 2014 were obtained from the British Columbia Burn Registry. These patients were compared with a control group of non-accelerant related burns. Clinical outcomes that were evaluated include inhalational injury, ICU length of stay, ventilator support, surgeries needed, and burn complications. Chi-square test was used to evaluate categorical data and Student's t-test was used to evaluate mean quantitative data with the p value set at 0.05. A logistic regression model was used to evaluate factors affecting burn complications. Accelerant-related burns represented 28.2% of all burn admissions (N=532) from 2009 to 2014. The accelerant group had higher percentage of patients with history of drug abuse and was associated with higher TBSA burns, ventilator support, ICU stay and pneumonia rates compared to the non-accelerant group. Within the accelerant group, there was no difference in clinical outcomes amongst people with or without history of drug abuse. Four cases were associated with methamphetamine manufacturing, all of which underwent ICU stay and ventilator support. Accelerant-related burns cause significant burden to the burn center. A significant proportion of these patients have history of drug abuse. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

A Burning Rate Emulator (BRE) for Study in Microgravity

NASA Technical Reports Server (NTRS)

Markan, A.; Sunderland, P. B.; Quintiere, J. G.; DeRis, J.; Stocker, D. P.

2015-01-01

A gas-fueled burner, the Burning Rate Emulator (BRE), is used to emulate condensed-phase fuel flames. The design has been validated to easily measure the burning behavior of condensed-phase fuels by igniting a controlled stream of gas fuel and diluent. Four properties, including the heat of combustion, the heat of gasification, the surface temperature, and the laminar smoke point, are assumed to be sufficient to define the steady burning rate of a condensed-phase fuel. The heat of gasification of the fuel is determined by measuring the heat flux and the fuel flow rate. Microgravity BRE tests in the NASA 5.2 s drop facility have examined the burning of pure methane and ethylene (pure and 50 in N2 balance). Fuel flow rates, chamber oxygen concentration and initial pressure have been varied. Two burner sizes, 25 and 50 mm respectively, are chosen to examine the nature of initial microgravity burning. The tests reveal bubble-like flames that increase within the 5.2s drop but the heat flux received from the flame appears to asymptotically approach steady state. Portions of the methane flames appear to locally detach and extinguish at center, while its shape remains fixed, but growing. The effective heat of gasification is computed from the final measured net heat flux and the fuel flow rate under the assumption of an achieved steady burning. Heat flux (or mass flux) and flame position are compared with stagnant layer burning theory. The analysis offers the prospect of more complete findings from future longer duration ISS experiments.

Evapotranspiration from a cypress and pine forest subjected to natural fires, Volusia County, Florida, 1998-99

USGS Publications Warehouse

Sumner, D.M.

2001-01-01

Daily values of evapotranspiration from a watershed in Volusia County, Florida, were estimated for a 2-year period (January 1998 through December 1999) by using an energy-budget variant of the eddy correlation method and a Priestley-Taylor model. The watershed consisted primarily of pine flatwood uplands interspersed within cypress wetlands. A drought-induced fire in spring 1998 burned about 40 percent of the watershed, most of which was subsequently logged. The model reproduced the 449 measured values of evapotranspiration reasonably well (r2=0.90) over a wide range of seasonal and surface-cover conditions. Annual evapotranspiration from the watershed was estimated to be 916 millimeters (36 inches) for 1998 and 1,070 millimeters (42 inches) for 1999. Evapotranspiration declined from near potential rates in the wet conditions of January 1998 to less than 50 percent of potential evapotranspiration after the fire and at the peak of the drought in June 1998. After the drought ended in early July 1998 and water levels returned to near land-surface, evapotranspiration increased sharply; however, the evapotranspiration rate was only about 60 percent of the potential rate in the burned areas, compared to about 90 percent of the potential rate in the unburned areas. This discrepancy can be explained as a result of fire damage to vegetation. Beginning in spring 1999, evapotranspiration from burned areas increased sharply relative to unburned areas, sometimes exceeding unburned evapotranspiration by almost 100 percent. Possible explanations for the dramatic increase in evapotranspiration from burned areas could include phenological changes associated with maturation or seasonality of plants that emerged after the fire or successional changes in composition of plant community within burned areas. Variations in daily evapotranspiration are primarily the result of variations in surface cover, net radiation, photosynthetically active radiation, air temperature, and water-table depth. A water budget for the watershed supports the validity of the daily measurements and estimates of evapotranspiration. A water budget constructed using independent estimates of average rates of rainfall, runoff, and deep leakage, as well as evapotranspiration, was consistent within 3.8 percent. An alternative water budget constructed using evapotrans-piration estimated by the standard eddy correlation method was consistent only within 9.1 percent. This result indicates that the standard eddy correlation method is not as accurate as the energy-budget variant.

Improving burn care and preventing burns by establishing a burn database in Ukraine.

PubMed

Fuzaylov, Gennadiy; Murthy, Sushila; Dunaev, Alexander; Savchyn, Vasyl; Knittel, Justin; Zabolotina, Olga; Dylewski, Maggie L; Driscoll, Daniel N

2014-08-01

Burns are a challenge for trauma care and a contribution to the surgical burden. The former Soviet republic of Ukraine has a foundation for burn care; however data concerning burns in Ukraine has historically been scant. The objective of this paper was to compare a new burn database to identify problems and implement improvements in burn care and prevention in this country. Retrospective analyses of demographic and clinical data of burn patients including Tukey's post hoc test, analysis of variance, and chi square analyses, and Fisher's exact test were used. Data were compared to the American Burn Association (ABA) burn repository. This study included 1752 thermally injured patients treated in 20 hospitals including Specialized Burn Unit in Municipal Hospital #8 Lviv, Lviv province in Ukraine. Scald burns were the primary etiology of burns injuries (70%) and burns were more common among children less than five years of age (34%). Length of stay, mechanical ventilation use, infection rates, and morbidity increased with greater burn size. Mortality was significantly related to burn size, inhalation injury, age, and length of stay. Wound infections were associated with burn size and older age. Compared to ABA data, Ukrainian patients had double the length of stay and a higher rate of wound infections (16% vs. 2.4%). We created one of the first burn databases from a region of the former Soviet Union in an effort to bring attention to burn injury and improve burn care. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

A Burke-Schumann analysis of diffusion-flame structures supported by a burning droplet

NASA Astrophysics Data System (ADS)

Nayagam, Vedha; Dietrich, Daniel L.; Williams, Forman A.

2017-07-01

A Burke-Schumann description of three different regimes of combustion of a fuel droplet in an oxidising atmosphere, namely the premixed-flame regime, the partial-burning regime and the diffusion-flame regime, is presented by treating the fuel and oxygen leakage fractions through the flame as known parameters. The analysis shows that the burning-rate constant, the flame-standoff ratio, and the flame temperature in these regimes can be obtained from the classical droplet-burning results by suitable definitions of an effective ambient oxygen mass fraction and an effective fuel concentration in the droplet interior. The results show that increasing oxygen leakage alone through the flame lowers both the droplet burning rate and the flame temperature, whereas leakage of fuel alone leaves the burning rate unaffected while reducing the flame temperature and moving the flame closer to the droplet surface. Solutions for the partial-burning regime are shown to exist only for a limited range of fuel and oxygen leakage fractions.

Characteristics code for shock initiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Partom, Y.

1986-10-01

We developed SHIN, a characteristics code for shock initiation studies. We describe in detail the equations of state, reaction model, rate equations, and numerical difference equations that SHIN incorporates. SHIN uses the previously developed surface burning reaction model which better represents the shock initiation process in TATB, than do bulk reaction models. A large number of computed simulations prove the code is a reliable and efficient tool for shock initiation studies. A parametric study shows the effect on build-up and run distance to detonation of (1) type of boundary condtion, (2) burning velocity curve, (3) shock duration, (4) rise timemore » in ramp loading, (5) initial density (or porosity) of the explosive, (6) initial temperature, and (7) grain size. 29 refs., 65 figs.« less

The impact of patient demographics and comorbidities upon burns admitted to Tygerberg Hospital Burns Unit, Western Cape, South Africa.

PubMed

Cloake, T; Haigh, T; Cheshire, J; Walker, D

2017-03-01

In South Africa, burns are a major public health problem responsible for significant morbidity and long-term physical disability. This is, in part, due to a significant proportion of the urban population living in poorly constructed, combustible accommodation. The presence of co-morbid diseases such as diabetes and malignancy in patients with burns has been associated with a poorer outcome. The impact of other diseases such as HIV has yet to be defined. A retrospective data collection study analysed the 221 patients admitted to Tygerberg Hospital Burns Unit in 2011 and the first six months of 2013. Using hospital records, patient demographic data was collected alongside burn agent, ICU admission, complications, and patient outcome in terms of length of stay and mortality. The most common burn agent was hot liquid (45.7%). A significant proportion of patients were subject to intentional attacks (34.3%). Shack fires and flame accounted cumulatively for 85% of total inhalational burns, the highest rates of admission to ICU (85.5%), the highest rate of complications, as well as 92.3% of all total fatalities. HIV+ patients had a higher mortality (13.3% vs 5%, p=0.22) and a higher complication rate (46.7% vs 30%, p=0.21). There was no difference in length of stay between the HIV+ and HIV- cohort (12days vs. 15.5 days, p=0.916). Burns are a significant yet preventable cause of mortality and morbidity. The rising number of shack fires, responsible for extensive burns and resultant mortality is concerning and indicates urgent attention and action. HIV complicates the recovery from burn and is responsible for an increased rate of in hospital mortality. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

The effect of smoking status on burn inhalation injury mortality.

PubMed

Knowlin, Laquanda; Stanford, Lindsay; Cairns, Bruce; Charles, Anthony

2017-05-01

Three factors that effect burn mortality are age, total body surface of burn (TBSA), and inhalation injury. Of the three, inhalation injury is the strongest predictor of mortality thus its inclusion in the revised Baux score (age+TBSA+17* (inhalation injury, 1=yes, 0=no)). However, the weighted contribution of specific comorbidities such as smoker status on mortality has traditionally not been accounted for nor studied in this subset of burn patients. We therefore sought to examine the impact of current tobacco and/or marijuana smoking in patients with inhalation injury. A retrospective analysis of patients admitted to a regional burn center from 2002 to 2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA, pre-existing comorbidities, and smoker status. Bivariate analysis was performed and logistic regression modeling using significant variables was utilized to estimate odds of mortality. There were a total of 7640 patients over the study period. 7% (n=580) of the burn cohort with inhalation injury were included in this study. In-hospital burn mortality for inhalation injury patients was 23%. Current smokers (20%) included cigarette smokers and marijuana users, 19% and 3%, respectively. Preexisting respiratory disease (17%) was present in 36% of smokers compared to 13% of non-smokers (p<0.001). Smokers had significantly lower mortality rate (9%) compared to non-smokers (26%, p<0.01). The logistic regression model for mortality outcomes identified statistically four significant variables: age, TBSA, ethnicity, and smoker status (OR=0.41, 95% CI=0.18-0.93). Presence of comorbidities, including preexisting respiratory disease, was not significant. In the sub group of burn patients with inhalation injury, the odds of mortality significantly decreased in pre-existing smokers after adjusting for significant covariates. We postulate that an immune tolerance mechanism that modulates and diminishes the pro-inflammatory response confers a survival advantage in smokers after exposure to acute smoke inhalation injury. Future prospective studies in human and/or animal models are needed to confirm these findings. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Experimentation and Modeling of Jet A Thermal Stability in a Heated Tube

NASA Technical Reports Server (NTRS)

Khodabandeh, Julia W.

2005-01-01

High performance aircraft typically use hydrocarbon fuel to regeneratively cool the airframe and engine components. As the coolant temperatures increase, the fuel may react with dissolved oxygen forming deposits that limit the regenerative cooling system performance. This study investigates the deposition of Jet A using a thermal stability experiment and computational fluid dynamics (CFD) modeling. The experimental portion of this study is performed with a high Reynolds number thermal stability (HiRets) tester in which fuel passes though an electrically heated tube and the fuel outlet temperature is held constant. If the thermal stability temperature of the fuel is exceeded, deposits form and adhere to the inside of the tube creating an insulating layer between the tube and the fuel. The HiRets tester measures the tube outer wall temperatures near the fuel outlet to report the effect of deposition occurring inside the tube. Final deposits are also estimated with a carbon burn off analysis. The CFD model was developed and used to simulate the fluid dynamics, heat transfer, chemistry, and transport of the deposit precursors. The model is calibrated to the experiment temperature results and carbon burn-off deposition results. The model results show that the dominant factor in deposition is the heated wall temperature and that most of the deposits are formed in the laminar sublayer. The models predicted a 7.0E-6 kilograms per square meter-sec deposition rate, which compared well to the carbon burn-off analysis deposition rate of 1.0E-6 kilograms per square meter-sec.

Epidemiology of burns undergoing hospitalization to the National Burns Unit in the Sultanate of Oman: a 25-year review.

PubMed

Al-Shaqsi, Sultan; Al-Kashmiri, Ammar; Al-Bulushi, Taimoor

2013-12-01

The aim of this study was to describe the epidemiology of burns admitted to the National Burns Unit (NBU) in the Sultanate of Oman between 1987 and 2011. This is a retrospective review of burn patients admitted to Oman's National Burns Unit (NBU) between 1987 and 2011. The data extracted from the national burn registry. The study describes the admission rate by gender and age groups, occupation, causes of burns, time-to-admission, length of stay and in-hospital mortality of burns between 1987 and 2011. During a 25-year from 1987 to 2011, there were 3531 burn patients admitted to the National Burns Unit in Oman. The average admission rate to NBU is 7.02 per 100,000 persons per year. On average, males were more likely to be admitted to the NBU than females during the study period (P value < 0.04). Patients aged 1-10 years old constituted 46.6% of caseload during the study period. Flames and scalds caused 88.4% of burns. About half of all patients admitted to the NBU have burns to more than 11% of total body surface area (TBSA). The average stay in hospital was estimated to be 15.3 days per patient. The average in-hospital mortality rate was estimated to be 8.2% per year (range 1.9-22%). Burns are significant public health issue in the Sultanate of Oman. Children are disproportionately over-represented in this study. Prevention programmes are urgently needed to address this "silent and costly epidemic." Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Prognostic factors in electrical burns: a review of 101 patients.

PubMed

Saracoglu, Ayten; Kuzucuoglu, Tamer; Yakupoglu, Sezer; Kilavuz, Oguzhan; Tuncay, Erhan; Ersoy, Burak; Demirhan, Recep

2014-06-01

Electrical burn wounds are among the most devastating of burns, with wide-ranging injuries. We aimed to document the factors affecting the mortality rate of patients presenting with electrical burn wounds to our regional burn centre. This retrospective study was conducted on 101 patients from January 2009 to June 2012. Factors were classified under 11 topics and evaluated according to their relationship with the mortality rate. The major causes of death in burn victims were multiple organ failure and infection. Twenty-six percent of the 101 patients died, all of whom were male. One (1.4%) of the patients who survived was female; 73 (98.6%) survivors were male. The mean age in the deceased group was statistically higher than that of the other patients (32.7 vs. 35.6 years; P < 0.05). All-cause mortality was 2.79 times higher for larger burns (> 25% total body surface area). The values for creatine kinase, creatine kinase-MB, total body surface area of burn, hospitalised period in the intensive care unit and intubation rate were significantly higher in the exitus group. Renal injury requiring haemofiltration was associated with an almost 12-fold increased risk for mortality. There was no statistically significant difference between patients regarding surgical interventions. Electrical injury remains a major cause of mortality and long-term disability among young people. Our data demonstrated several risk factors associated with increased mortality rate in patients with electrical burn wounds. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Effect of Chamber Pressurization Rate on Combustion and Propagation of Solid Propellant Cracks

NASA Astrophysics Data System (ADS)

Yuan, Wei-Lan; Wei, Shen; Yuan, Shu-Shen

2002-01-01

area of the propellant grain satisfies the designed value. But cracks in propellant grain can be generated during manufacture, storage, handing and so on. The cracks can provide additional surface area for combustion. The additional combustion may significantly deviate the performance of the rocket motor from the designed conditions, even lead to explosive catastrophe. Therefore a thorough study on the combustion, propagation and fracture of solid propellant cracks must be conducted. This paper takes an isolated propellant crack as the object and studies the effect of chamber pressurization rate on the combustion, propagation and fracture of the crack by experiment and theoretical calculation. deformable, the burning inside a solid propellant crack is a coupling of solid mechanics and combustion dynamics. In this paper, a theoretical model describing the combustion, propagation and fracture of the crack was formulated and solved numerically. The interaction of structural deformation and combustion process was included in the theoretical model. The conservation equations for compressible fluid flow, the equation of state for perfect gas, the heat conducting equation for the solid-phase, constitutive equation for propellant, J-integral fracture criterion and so on are used in the model. The convective burning inside the crack and the propagation and fracture of the crack were numerically studied by solving the set of nonlinear, inhomogeneous gas-phase governing equations and solid-phase equations. On the other hand, the combustion experiments for propellant specimens with a precut crack were conducted by RTR system. Predicted results are in good agreement with experimental data, which validates the reasonableness of the theoretical model. Both theoretical and experimental results indicate that the chamber pressurization rate has strong effects on the convective burning in the crack, crack fracture initiation and fracture pattern.

The impact of antibiotic impregnated PICC lines on the incidence of bacteremia in a regional burn center.

PubMed

Armstrong, Shannon D; Thomas, Wendy; Neaman, Keith C; Ford, Ronald D; Paulson, Jayne

2013-06-01

Peripherally inserted central catheters (PICCs) have been used increasingly in burn patients who often have decreased intravascular volumes and obtaining intravascular access for resuscitative efforts can be difficult. A potentially serious complication is bloodstream infection. The purpose of our study is to examine the impact of antibiotic impregnated PICC lines on the bacteremia rate in a regional burn center. Consecutive patients admitted to the burn unit and receiving an antibiotic impregnated PICC line were included in the study. Baseline demographics and bacteremia rate was recorded. A retrospective chart review was then undertaken of the 30 consecutive patients admitted to the burn unit and receiving a PICC line prior to the study period. Nineteen patients were enrolled over the two-year period. The bacteremia rate for the study group was 0% compared to the 50% bacteremia rate of the retrospective control group (p=<0.001). Antibiotic impregnated PICC lines decrease the bacteremia rate in our burn population. This has potential benefits for both patient morbidity and mortality as well as potential cost savings for the healthcare system. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

Chemical analysis of Agaricus blazei polysaccharides and effect of the polysaccharides on IL-1beta mRNA expression in skin of burn wound-treated rats.

PubMed

Sui, ZhiFu; Yang, RongYa; Liu, Biao; Gu, TingMin; Zhao, Zhili; Shi, Dongfang; Chang, DongQing

2010-08-01

Agaricus blazei polysaccharides were analyzed by GC-MS. Results indicated that the polysaccharides contained glucose (93.87%), mannose (3.54%), and arabinose (2.25%). The compositional analysis was completed by the methylation data. These data indicated that Agaricus blazei polysaccharides are glucans. Compared to model rats, rats fed with Agaricus blazei polysaccharides showed a decrease of ratio of IL-1beta/beta-actin and IL-1beta level in skin of burn wound. Recovery rate of wound skin increased with increasing dose of polysaccharides. The results indicated that Agaricus blazei polysaccharides could be useful in promote burn wound healing. Copyright 2010 Elsevier B.V. All rights reserved.

Pellet fuelling requirements to allow self-burning on a helical-type fusion reactor

NASA Astrophysics Data System (ADS)

Sakamoto, R.; Miyazawa, J.; Yamada, H.; Masuzaki, S.; Sagara, A.; the FFHR Design Group

2012-08-01

Pellet refuelling conditions to sustain a self-burning plasma have been investigated by extrapolating the confinement property of the LHD plasma, which appears to be governed by a gyro-Bohm-type confinement property. The power balance of the burning plasma is calculated taking into account the profile change with pellet deposition and subsequent density relaxation. A self-burning plasma is achieved within the scope of conventional pellet injection technology. However, a very small burn-up rate of 0.18% is predicted. Higher velocity pellet injection is effective in improving the burn-up rate by deepening particle deposition, whereas deep fuelling leads to undesirable fluctuation of the fusion output.

Patient experiences of burn scars in adults and children and development of a health-related quality of life conceptual model: A qualitative study.

PubMed

Simons, Megan; Price, Nathaniel; Kimble, Roy; Tyack, Zephanie

2016-05-01

The aim of this study was to understand the impact of burn scars on health-related quality of life (HRQOL) from the perspective of adults and children with burn scars, and caregivers to inform the development of a conceptual model of burn scar HRQOL. Twenty-one participants (adults and children) with burn scars and nine caregivers participated in semi-structured, face-to-face interviews between 2012 and 2013. During the interviews, participants were asked to describe features about their (or their child's) burn scars and its impact on everyday life. Two coders conducted thematic analysis, with consensus achieved through discussion and review with a third coder. The literature on HRQOL models was then reviewed to further inform the development of a conceptual model of burn scar HRQOL. Five themes emerged from the qualitative data: 'physical and sensory symptoms', 'impact of burn scar interventions', 'impact of burn scar symptoms', 'personal factors' and 'change over time'. Caregivers offered further insights into family functioning after burn, and the impacts of burn scars and burn scar interventions on family life. In the conceptual model, symptoms (sensory and physical) of burn scars are considered proximal to HRQOL, with distal indicators including functioning (physical, emotional, social, cognitive), individual factors and the environment. Overall quality of life was affected by HRQOL. Understanding the impact of burn scars on HRQOL and the development of a conceptual model will inform future burn scar research and clinical practice. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

A Descriptive Study of the Temporal Patterns of Volume and Contents Change in Human Acute Burn Edema: Application in Evidence-Based Intervention and Research Design.

PubMed

Edgar, Dale W; Fear, Mark; Wood, Fiona M

2016-01-01

Edema after burn contributes significantly to burn wound depth conversion. In humans after burn injury, there is a lack of detailed understanding of the contents and temporal changes in volume of acute tissue edema. The novel findings of these studies relate to the collection of edema fluid after partial-thickness burn injury. Edema volume peaks on day 1 after burn without formal fluid resuscitation. The studies indicated that the peak was on day 2 for a resuscitated burn. In contrast, animal studies suggest that the peak of edema occurs by or before day 1 after injury. The findings confirm the pitfalls of evidence derived from animal models and assuming direct transference to humans. Postburn edema was demonstrated to be a high-protein fluid (ie, ≥10 g/L) for the duration of the inflammatory period. The presence of high-protein edema presents greater challenges to clinicians developing novel treatment options. The rate of volume change over time tapered to insignificant levels after day 4 following burn. Greater than 98% of the edema contents was fluid. However, the size of particulate matter did not preclude it passing through patent lymphatic collectors. The results indicate a necessity for urgent postburn intervention, which should incorporate the active stimulation of the lymphatic system to improve efficacy of edema removal.

Combustion characteristics of nanoaluminum, liquid water, and hydrogen peroxide mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabourin, J.L.; Yetter, R.A.; Risha, G.A.

2008-08-15

An experimental investigation of the combustion characteristics of nanoaluminum (nAl), liquid water (H{sub 2}O{sub (l)}), and hydrogen peroxide (H{sub 2}O{sub 2}) mixtures has been conducted. Linear and mass-burning rates as functions of pressure, equivalence ratio ({phi}), and concentration of H{sub 2}O{sub 2} in H{sub 2}O{sub (l)} oxidizing solution are reported. Steady-state burning rates were obtained at room temperature using a windowed pressure vessel over an initial pressure range of 0.24 to 12.4 MPa in argon, using average nAl particle diameters of 38 nm, {phi} from 0.5 to 1.3, and H{sub 2}O{sub 2} concentrations between 0 and 32% by mass. Atmore » a nominal pressure of 3.65 MPa, under stoichiometric conditions, mass-burning rates per unit area ranged between 6.93 g/cm{sup 2} s (0% H{sub 2}O{sub 2}) and 37.04 g/cm{sup 2} s (32% H{sub 2}O{sub 2}), which corresponded to linear burning rates of 9.58 and 58.2 cm/s, respectively. Burning rate pressure exponents of 0.44 and 0.38 were found for stoichiometric mixtures at room temperature containing 10 and 25% H{sub 2}O{sub 2}, respectively, up to 5 MPa. Burning rates are reduced above {proportional_to}5 MPa due to the pressurization of interstitial spaces of the packed reactant mixture with argon gas, diluting the fuel and oxidizer mixture. Mass burning rates were not measured above {proportional_to}32% H{sub 2}O{sub 2} due to an anomalous burning phenomena, which caused overpressurization within the quartz sample holder, leading to tube rupture. High-speed imaging displayed fingering or jetting ahead of the normal flame front. Localized pressure measurements were taken along the sample length, determining that the combustion process proceeded as a normal deflagration prior to tube rupture, without significant pressure buildup within the tube. In addition to burning rates, chemical efficiencies of the combustion reaction were determined to be within approximately 10% of the theoretical maximum under all conditions studied. (author)« less

Predictors of sustaining burn injury: does the use of common prevention strategies matter?

PubMed

Taira, Breena R; Cassara, Guy; Meng, Hongdao; Salama, Michael N; Chohan, Jasmine; Sandoval, Steven; Singer, Adam J

2011-01-01

The incidence of burn injury has decreased over the past several decades. Although this has been largely attributed to increased prevention awareness, few studies evaluate the effectiveness of implementing standard burn prevention strategies in preventing burn injury. The authors hypothesized that patients who sustain burns use burn prevention strategies less frequently than those who do not. This was a case-control study composed of a prospective survey questionnaire and retrospective burn registry query, which was performed in a suburban academic medical center with a burn unit. All burn patients seen by the burn service in the year 2008 and a nonrandom sample of nonburned emergency department patients and visitors during the same time period were enrolled. Demographics included age, gender, income, education, house type, insurance status, and prevention strategy usage including smoke alarms, carbon monoxide detectors, fire extinguishers, and escape plans. The primary outcome of interest in this study was burn injury. Chi-square tests were used to compare rates, Student's t-tests were used to compare mean values of continuous variables between burn patients and others, and multivariate logistic regression was used to determine the strongest predictors of sustaining burn injury. One hundred ninety-four burn patients and 348 nonburned emergency department patients and visitors were surveyed. Burn patients reported the same rates of smoke alarm usage (96.9 vs 96.3%, P = .692), carbon monoxide detectors (75.3 vs 67.2%, P = .05), and higher rates of fire extinguisher ownership (80.4 vs 72.7%, P = .045) when compared with others. In multivariable analysis, the strongest predictor of sustaining burn injury was less than high school education (odds ratio [OR] 3.61, 95% confidence interval [CI] 1.27-10.27), whereas English as a primary language (OR 0.48, 95% CI 0.26-0.89), a graduate degree (OR 0.10, 95% CI 0.02-0.42), income >$50,000 (OR 0.46, 95% CI 0.29-0.72), and keeping flammable liquids in a locked place (OR 0.59, 95% CI 0.44-0.80) were protective against burn injury. Smoke alarms (OR 0.75, 95% CI 0.22-2.61), fire extinguishers (OR 1.34, 95% CI 0.80-2.32), and having an escape plan (OR 0.85, 95% CI 0.56-1.29) were not protective. Patients who sustain burn injury use burn prevention strategies at similar rates when compared with those who do not. When holding demographic characteristics constant, utilization of most burn prevention strategies is not protective of sustaining burn injury. Those with lower levels of education and income remain more susceptible to burn injury.

Effects of burn location and investigator on burn depth in a porcine model.

PubMed

Singer, Adam J; Toussaint, Jimmy; Chung, Won Taek; Thode, Henry C; McClain, Steve; Raut, Vivek

2016-02-01

In order to be useful, animal models should be reproducible and consistent regardless of sampling bias, investigator creating burn, and burn location. We determined the variability in burn depth based on biopsy location, burn location and investigator in a porcine model of partial thickness burns. 24 partial thickness burns (2.5 cm by 2.5 cm each) were created on the backs of 2 anesthetized pigs by 2 investigators (one experienced, one inexperienced) using a previously validated model. In one of the pigs, the necrotic epidermis covering each burn was removed. Five full thickness 4mm punch biopsies were obtained 1h after injury from the four corners and center of the burns and stained with Hematoxylin and Eosin and Masson's trichrome for determination of burn depth by a board certified dermatopathologist blinded to burn location and investigator. Comparisons of burn depth by biopsy location, burn location and investigator were performed with t-tests and ANOVA as appropriate. The mean (SD) depth of injury to blood vessels (the main determinant of burn progression) in debrided and non-debrided pigs pooled together was 1.8 (0.3)mm, which included 75% of the dermal depth. Non-debrided burns were 0.24 mm deeper than debrided burns (P<0.001). Burn depth increased marginally from cephalic to caudal in non-debrided burns, but showed no statistical differences for these locations, in debrided burns. Additionally, there were also no statistical differences in burn depths from midline to lateral in either of these burn types. Burn depth was similar for both investigators and among biopsy locations. Burn depth was greater for caudal locations in non-debrided burns and overall non-debrided burns were deeper than debrided burns. However, burn depth did not differ based on investigator, biopsy site, and medial-lateral location. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

40 CFR 60.106 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... determine opacity. (c) If auxiliary liquid or solid fossil-fuels are burned in an incinerator-waste heat... rate from solid or liquid fossil fuel, million J/hr (million Btu/hr). Rc = Coke burn-off rate, Mg coke... supplemental gaseous, liquid, or solid fossil fuel is burned, testing shall be conducted at a point between the...

40 CFR 60.106 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... determine opacity. (c) If auxiliary liquid or solid fossil-fuels are burned in an incinerator-waste heat... rate from solid or liquid fossil fuel, million J/hr (million Btu/hr). Rc = Coke burn-off rate, Mg coke... supplemental gaseous, liquid, or solid fossil fuel is burned, testing shall be conducted at a point between the...

40 CFR 60.106 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... determine opacity. (c) If auxiliary liquid or solid fossil-fuels are burned in an incinerator-waste heat... rate from solid or liquid fossil fuel, million J/hr (million Btu/hr). Rc = Coke burn-off rate, Mg coke... supplemental gaseous, liquid, or solid fossil fuel is burned, testing shall be conducted at a point between the...

Ciprofloxacin-lidocaine-based hydrogel: development, characterization, and in vivo evaluation in a second-degree burn model.

PubMed

Sanchez, María Florencia; Breda, Susana Andrea; Soria, Elio Andrés; Tártara, Luis Ignacio; Manzo, Rubén Hilario; Olivera, María Eugenia

2018-04-13

The purpose of this work was to develop an effective carbomer hydrogel to be used to treat second-degree burns that combined ciprofloxacin and lidocaine (CbCipLid hydrogel). Its antibiotic and anesthetic efficacy and the physical and chemical properties of the CbCipLid hydrogel (release rate and kinetics, rheology, appearance, and drug content) were evaluated both before and after a sterilization cycle and also after 6 months of storage. For the in vivo studies, second-degree burns were developed in a rat model. Animals were divided into three groups: CbCipLid hydrogel, silver sulfadiazine cream (reference), and carbomer hydrogel (as control). The treatments were applied daily for 21 days, and the healing was monitored by macroscopic observation and histologic evaluation. The anesthetic effect was evaluated through the corneal touch threshold in a rabbit eye model. The CbCipLid hydrogel obtained is transparent and allows the loading of ciprofloxacin above its solubility at a neutral pH, with a rheology which is convenient for topical administration. Its physical and chemical properties remained unchanged after sterilization and for at least six additional months. Both ciprofloxacin and lidocaine are reversibly released from the CbCipLid hydrogel with a kinetics fitting the Higuchi model. The presence of a biologic-like fluid increased the rate of drug delivery through an ionic exchange mechanism. Treatment with the CbCipLid hydrogel decreased the wound-healing period, compared with the reference, and was associated with a greater number of fibroblasts and a faster rate of epithelialization and dermis reconstruction. These differences were assigned to the moist environment provided by the hydrogel and also to the presence of a therapeutic concentration of ciprofloxacin. Moreover, CbCipLid hydrogel provides an immediate anesthetic effect, which is significantly more intense than that of the reference. Based on these results, it is believed that the CbCipLid hydrogel could be a potential candidate in the prophylaxis/treatment of second-degree burns.

[Epidemiological investigation on 2 133 hospitalized patients with electrical burns].

PubMed

Jiang, M J; Li, Z; Xie, W G

2017-12-20

Objective: To analyze the epidemiological characteristics of the hospitalized patients with electrical burns in Institute of Burns of Tongren Hospital of Wuhan University & Wuhan Third Hospital (hereinafter referred to as Institute of Burns of Wuhan Third Hospital), so as to provide reference for the prevention and treatment of electrical burns. Methods: Medical records of all hospitalized burn patients in Institute of Burns of Wuhan Third Hospital from January 2004 to December 2016 were collected. Genders, ages, social categories, seasons of injury, total burn areas, depths of wounds, electrical voltages of injury, sites of wound, treatment methods, amputation rates, lengths of hospital stay, operation costs, hospitalization costs, and treatment outcomes of the electrical burn patients were collected. Treatment methods, lengths of hospital stay, operation costs, and hospitalization costs of the thermal burn patients were collected and compared with those of the electrical burn patients. Electrical voltages of injury, amputation rates, operation costs, hospitalization costs, and treatment outcomes were compared and analyzed between the electrical contact burn patients and the electrical arc burn patients. Data were processed with Chi-square test and Wilcoxon rank-sum test. Results: During the 13 years, 23 534 burn patients were admitted to Institute of Burns of Wuhan Third Hospital, among whom 2 133 (9.1%) were with electrical burns, without obvious variation in admission number of electrical burn patients every year. There were 1 418 patients (66.5%) with electrical contact burns and 715 patients (33.5%) with electrical arc burns. The ratio of male to female was 11.2∶1.0 among the electrical burn patients with known genders. The proportions of three age groups of more than 20 years old and less than or equal to 30 years old, more than 30 years old and less than or equal to 40 years old, and more than 40 years old and less than or equal to 50 years old were relatively higher, which were 18.3% (391/2 133), 22.1% (471/2 133), and 24.6% (525/2 133), respectively. The first three social category groups in proportions were workers, peasants, and preschool children, which were 57.9% (1 235/2 133), 14.6% (311/2 133), and 6.0% (128/2 133), respectively. Among the electrical burn patients with known seasons of injury, most cases were injured in summer (659 cases, accounting for 34.1%), obviously more than the proportions in autumn (537 cases, accounting for 27.8%), spring (455 cases, accounting for 23.5%), and winter (283 cases, accounting for 14.6%), with χ (2) values from 8.414 to 149.573, P values below 0.01. The group of patients with total burn areas less than 10% total body surface area (TBSA) occupied the highest proportion (1 603 cases, accounting for 75.15%), among whom 229 (10.74%) were with scattered small wounds which were less than 1% TBSA. The percentage of electrical contact burn patients with deep wounds was 79.1% (1 122/1 418), which was obviously higher than 2.5% (18/715) of the electrical arc burn patients ( χ (2)=381.741, P <0.001). Among the patients with known electrical voltages of injury, patients injured by high voltage among the electrical contact burn patients accounted for 78.4% (469/598), which was obviously higher than 8.7% (11/127) of the electrical arc burn patients ( χ (2)=227.893, P <0.001). The most common wound site of the electrical burn patients was upper limbs (1 650 cases, accounting for 63.2%), followed by lower limbs (382 cases, accounting for 14.6%), head and neck (292 cases, accounting for 11.2%), trunk (247 cases, accounting for 9.5%), and hip and perineum (40 cases, accounting for 1.5%). The operation rate of electrical burn patients was 32.4% (691/2 133), obviously higher than 19.1% (3 860/20 209)of the thermal burn patients during the same period ( χ (2)=210.255, P <0.001). Wounds of 116 electrical contact burn patients were repaired with free flap by vascular anastomosis, of which 9 (7.8%) failed. The length of hospital stay, the operation cost, and the hospitalization cost of electrical burn patients were (28±29) d, (9 534±16 935) and (44 258±93 012) Yuan, respectively, obviously longer or higher than those of the thermal burn patients during the same period [(17±19) d, (2 990±8 916) and (23 291±88 340) Yuan, respectively, with Z values from -21.323 to -10.996, P values below 0.001]. The amputation rate and the death rate of electrical burn patients were 3.8% (82/2 133) and 0.8% (16/2 133) respectively. Compared with those of electrical arc burn patients, the amputation rate and the operation cost of electrical contact burn patients were obviously higher ( χ (2)=36.970, Z =-11.351, P values below 0.001), and the length of hospital stay of electrical contact burn patients was obviously longer ( Z =-5.181, P <0.001). There were no significant differences in hospitalization cost and treatment outcome between the electrical contact burn patients and the electrical arc burn patients ( Z =-1.461, χ (2)=1.673, P values above 0.05). Conclusions: The number and the proportion of hospitalized electrical burn patients in Institute of Burns of Wuhan Third Hospital were relatively high, indicating a hard task of prevention for electrical burns in Wuhan area. Working-age workers and farmers, and preschool children were the key groups in prevention from electrical burns. The length of hospital stay, the operation cost, and the hospitalization cost of electrical burn patients were obviously higher than those of thermal burn patients. The amputation rate and the operation cost of electrical contact burn patients were obviously higher than those of electrical arc burn patients, but there were no obvious differences in hospitalization cost or treatment outcome between them. Actively using tissue flaps including free flap to repair of wounds may be helpful to reduce the amputation rate, improve the results, and shorten the time of treatment.

Biomass burning fuel consumption dynamics in the tropics and subtropics assessed from satellite

NASA Astrophysics Data System (ADS)

Andela, Niels; van der Werf, Guido R.; Kaiser, Johannes W.; van Leeuwen, Thijs T.; Wooster, Martin J.; Lehmann, Caroline E. R.

2016-06-01

Landscape fires occur on a large scale in (sub)tropical savannas and grasslands, affecting ecosystem dynamics, regional air quality and concentrations of atmospheric trace gasses. Fuel consumption per unit of area burned is an important but poorly constrained parameter in fire emission modelling. We combined satellite-derived burned area with fire radiative power (FRP) data to derive fuel consumption estimates for land cover types with low tree cover in South America, Sub-Saharan Africa, and Australia. We developed a new approach to estimate fuel consumption, based on FRP data from the polar-orbiting Moderate Resolution Imaging Spectroradiometer (MODIS) and the geostationary Spinning Enhanced Visible and Infrared Imager (SEVIRI) in combination with MODIS burned-area estimates. The fuel consumption estimates based on the geostationary and polar-orbiting instruments showed good agreement in terms of spatial patterns. We used field measurements of fuel consumption to constrain our results, but the large variation in fuel consumption in both space and time complicated this comparison and absolute fuel consumption estimates remained more uncertain. Spatial patterns in fuel consumption could be partly explained by vegetation productivity and fire return periods. In South America, most fires occurred in savannas with relatively long fire return periods, resulting in comparatively high fuel consumption as opposed to the more frequently burning savannas in Sub-Saharan Africa. Strikingly, we found the infrequently burning interior of Australia to have higher fuel consumption than the more productive but frequently burning savannas in northern Australia. Vegetation type also played an important role in explaining the distribution of fuel consumption, by affecting both fuel build-up rates and fire return periods. Hummock grasslands, which were responsible for a large share of Australian biomass burning, showed larger fuel build-up rates than equally productive grasslands in Africa, although this effect might have been partially driven by the presence of grazers in Africa or differences in landscape management. Finally, land management in the form of deforestation and agriculture also considerably affected fuel consumption regionally. We conclude that combining FRP and burned-area estimates, calibrated against field measurements, is a promising approach in deriving quantitative estimates of fuel consumption. Satellite-derived fuel consumption estimates may both challenge our current understanding of spatiotemporal fuel consumption dynamics and serve as reference datasets to improve biogeochemical modelling approaches. Future field studies especially designed to validate satellite-based products, or airborne remote sensing, may further improve confidence in the absolute fuel consumption estimates which are quickly becoming the weakest link in fire emission estimates.

Mountain plover nest survival in relation to prairie dog and fire dynamics in shortgrass steppe

USGS Publications Warehouse

Augustine, David J.; Skagen, Susan K.

2014-01-01

Disturbed xeric grasslands with short, sparse vegetation provide breeding habitat for mountain plovers (Charadrius montanus) across the western Great Plains. Maintaining local disturbance regimes through prairie dog conservation and prescribed fire may contribute to the sustainability of recently declining mountain plover populations, but these management approaches can be controversial. We estimated habitat-specific mountain plover densities and nest survival rates on black-tailed prairie dog (Cynomys ludovicianus) colonies and burns in the shortgrass steppe of northeastern Colorado. Mountain plover densities were similar on prairie dog colonies (5.9 birds/km2; 95% CI = 4.7–7.4) and sites burned during the preceding dormant season (6.7 birds/km2; 95% CI = 4.6–9.6), whereas the 29-day nest survival rate was greater on prairie dog colonies (0.81 in 2011 and 0.39 in 2012) compared to the burned sites (0.64 in 2011 and 0.17 in 2012). Reduced nest survival in 2012 compared to 2011 was associated with higher maximum daily temperatures in 2012, consistent with a previous weather-based model of mountain plover nest survival in the southern Great Plains. Measurements of mountain plover density relative to time since disturbance showed that removal of prairie dog disturbance by sylvatic plague reduced mountain plover density by 70% relative to active prairie dog colonies after 1 year. Plover densities declined at a similar rate (by 78%) at burned sites between the first and second post-burn growing season. Results indicate that black-tailed prairie dog colonies are a particularly important nesting habitat for mountain plovers in the southern Great Plains. In addition, findings suggest that prescribed burning can be a valuable means to create nesting habitat in landscapes where other types of disturbances (such as prairie dog colonies) are limited in distribution and size. 

Progress in the development of the MARBLE platform for studying thermonuclear burn in the presence of heterogeneous mix on OMEGA and the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, T. J.; Douglas, M. R.; Fincke, J. R.

Mix of ablator material into fuel of an ICF capsule adds non-burning material, diluting the fuel and reducing burn. The amount of the reduction is dependent in part on the morphology of the mix. A probability distribution function (PDF) burn model has been developed [6] that utilizes the average concentration of mixed materials as well as the variance in this quantity across cells provided by the BHR turbulent transport model [3] and its revisions [4] to describe the mix in terms of a PDF of concentrations of fuel and ablator material, and provides the burn rate in mixed material. Workmore » is underway to develop the MARBLE ICF platform for use on the National Ignition Facility in experiments to quantify the influence of heterogeneous mix on fusion burn. This platform consists of a plastic (CH) capsule filled with a deuterated plastic foam (CD) with a density of a few tens of milligrams per cubic centimeter, with tritium gas filling the voids in the foam. This capsule will be driven using x-ray drive on NIF, and the resulting shocks will induce turbulent mix that will result in the mixing of deuterium from the foam with the tritium gas. In order to affect the morphology of the mix, engineered foams with voids of diameter up to 100 microns will be utilized. The degree of mix will be determined from the ratio of DT to DD neutron yield. As the mix increases, the yield from reactions between the deuterium of the CD foam with tritium from the gas will increase. Lastly, the ratio of DT to DD neutrons will be compared to a variation of the PDF burn model that quantifies reactions from initially separated reactants.« less

Progress in the development of the MARBLE platform for studying thermonuclear burn in the presence of heterogeneous mix on OMEGA and the National Ignition Facility

DOE PAGES

Murphy, T. J.; Douglas, M. R.; Fincke, J. R.; ...

2016-05-26

Mix of ablator material into fuel of an ICF capsule adds non-burning material, diluting the fuel and reducing burn. The amount of the reduction is dependent in part on the morphology of the mix. A probability distribution function (PDF) burn model has been developed [6] that utilizes the average concentration of mixed materials as well as the variance in this quantity across cells provided by the BHR turbulent transport model [3] and its revisions [4] to describe the mix in terms of a PDF of concentrations of fuel and ablator material, and provides the burn rate in mixed material. Workmore » is underway to develop the MARBLE ICF platform for use on the National Ignition Facility in experiments to quantify the influence of heterogeneous mix on fusion burn. This platform consists of a plastic (CH) capsule filled with a deuterated plastic foam (CD) with a density of a few tens of milligrams per cubic centimeter, with tritium gas filling the voids in the foam. This capsule will be driven using x-ray drive on NIF, and the resulting shocks will induce turbulent mix that will result in the mixing of deuterium from the foam with the tritium gas. In order to affect the morphology of the mix, engineered foams with voids of diameter up to 100 microns will be utilized. The degree of mix will be determined from the ratio of DT to DD neutron yield. As the mix increases, the yield from reactions between the deuterium of the CD foam with tritium from the gas will increase. Lastly, the ratio of DT to DD neutrons will be compared to a variation of the PDF burn model that quantifies reactions from initially separated reactants.« less

Prophylactic antibiotics for burns patients: systematic review and meta-analysis

PubMed Central

Avni, Tomer; Levcovich, Ariela; Ad-El, Dean D; Leibovici, Leonard

2010-01-01

Objective To assess the evidence for prophylactic treatment with systemic antibiotics in burns patients. Design Systematic review and meta-analysis of randomised or quasi-randomised controlled trials recruiting burns inpatients that compared antibiotic prophylaxis (systemic, non-absorbable, or topical) with placebo or no treatment. Data sources PubMed, Cochrane Library, LILACS, Embase, conference proceedings, and bibliographies. No language, date, or publication status restrictions were imposed. Review methods Two reviewers independently extracted data. The primary outcome was all cause mortality. Risk or rate ratios with 95% confidence intervals were pooled with a fixed effect model if no heterogeneity was present. Results 17 trials were included. Trials that assessed systemic antibiotic prophylaxis given for 4-14 days after admission showed a significant reduction in all cause mortality (risk ratio 0.54, 95% confidence interval 0.34 to 0.87, five trials). The corresponding number needed to treat was 8 (5 to 33), with a control event rate of 26%. Perioperative non-absorbable or topical antibiotics alone did not significantly affect mortality. There was a reduction in pneumonia with systemic prophylaxis and a reduction in wound infections with perioperative prophylaxis. Staphylococcus aureus infection or colonisation was reduced with anti-staphylococcal antibiotics. In three trials, resistance to the antibiotic used for prophylaxis significantly increased (rate ratio 2.84, 1.38 to 5.83). The overall methodological quality of the trials was poor. Conclusions Prophylaxis with systemic antibiotics has a beneficial effect in burns patients, but the methodological quality of the data is weak. As such prophylaxis is currently not recommended for patients with severe burns other than perioperatively, there is a need for randomised controlled trials to assess its use. PMID:20156911

Burning high-level TRU waste in fusion fission reactors

NASA Astrophysics Data System (ADS)

Shen, Yaosong

2016-09-01

Recently, the concept of actinide burning instead of a once-through fuel cycle for disposing spent nuclear fuel seems to get much more attention. A new method of burning high-level transuranic (TRU) waste combined with Thorium-Uranium (Th-U) fuel in the subcritical reactors driven by external fusion neutron sources is proposed in this paper. The thorium-based TRU fuel burns all of the long-lived actinides via a hard neutron spectrum while outputting power. A one-dimensional model of the reactor concept was built by means of the ONESN_BURN code with new data libraries. The numerical results included actinide radioactivity, biological hazard potential, and much higher burnup rate of high-level transuranic waste. The comparison of the fusion-fission reactor with the thermal reactor shows that the harder neutron spectrum is more efficient than the soft. The Th-U cycle produces less TRU, less radiotoxicity and fewer long-lived actinides. The Th-U cycle provides breeding of 233U with a long operation time (>20 years), hence significantly reducing the reactivity swing while improving safety and burnup.

Internal and Surface Phenomena in Heterogenous Metal Combustion

NASA Technical Reports Server (NTRS)

Dreizin, Edward L.

1997-01-01

The phenomenon of gas dissolution in burning metals was observed in recent metal combustion studies, but it could not be adequately explained by the traditional metal combustion models. The research reported here addresses heterogeneous metal combustion with emphasis on the processes of oxygen penetration inside burning metal and its influence on the metal combustion rate, temperature history, and disruptive burning. The unique feature of this work is the combination of the microgravity environment with a novel micro-arc generator of monodispersed metal droplets, ensuring repeatable formation and ignition of uniform metal droplets with a controllable initial temperature and velocity. Burning droplet temperature is measured in real time with a three wavelength pyrometer. In addition, particles are rapidly quenched at different combustion times, cross-sectioned, and examined using SEM-based techniques to retrieve the internal composition history of burning metal particles. When the initial velocity of a spherical particle is nearly zero, the microgravity environment makes it possible to study the flame structure, the development of flame nonsymmetry, and correlation of the flame shape with the heterogeneous combustion processes.

Thermal Decomposition Behaviors and Burning Characteristics of AN/Nitramine-Based Composite Propellant

NASA Astrophysics Data System (ADS)

Naya, Tomoki; Kohga, Makoto

2015-04-01

Ammonium nitrate (AN) has attracted much attention due to its clean burning nature as an oxidizer. However, an AN-based composite propellant has the disadvantages of low burning rate and poor ignitability. In this study, we added nitramine of cyclotrimethylene trinitramine (RDX) or cyclotetramethylene tetranitramine (HMX) as a high-energy material to AN propellants to overcome these disadvantages. The thermal decomposition and burning rate characteristics of the prepared propellants were examined as the ratio of AN and nitramine was varied. In the thermal decomposition process, AN/RDX propellants showed unique mass loss peaks in the lower temperature range that were not observed for AN or RDX propellants alone. AN and RDX decomposed continuously as an almost single oxidizer in the AN/RDX propellant. In contrast, AN/HMX propellants exhibited thermal decomposition characteristics similar to those of AN and HMX, which decomposed almost separately in the thermal decomposition of the AN/HMX propellant. The ignitability was improved and the burning rate increased by the addition of nitramine for both AN/RDX and AN/HMX propellants. The increased burning rates of AN/RDX propellants were greater than those of AN/HMX. The difference in the thermal decomposition and burning characteristics was caused by the interaction between AN and RDX.

Combustion of liquid fuel droplets in supercritical conditions

NASA Technical Reports Server (NTRS)

Shuen, J. S.; Yang, Vigor

1991-01-01

A comprehensive analysis of liquid-fuel droplet combustion in both sub- and super-critical environments has been conducted. The formulation is based on the complete conservation equations for both gas and liquid phases, and accommodates finite-rate chemical kinetics and a full treatment of liquid-vapor phase equilibrium at the droplet surface. The governing equations and the associated interface boundary conditions are solved numerically using a fully coupled, implicit scheme with the dual time-stepping integration technique. The model is capable of treating the entire droplet history, including the transition from the subcritical to the supercritical state. As a specific example, the combustion of n-pentane fuel droplets in air is studied for pressures of 5-140 atm. Results indicate that the ambient gas pressure exerts significant control of droplet gasification and burning processes through its influences on the fluid transport, gas/liquid interface thermodynamics, and chemical reactions. The droplet gasification rate increases progressively with pressure. However, the data for the overall burnout time exhibits a significant variation near the critical burning pressure, mainly as a result of reduced mass-diffusion rate and latent heat of vaporization with increased pressure. The influence of droplet size on the burning characteristics is also noted.

Kinetic Energy Transfer Process in a Double Shell Leading to Robust Burn

NASA Astrophysics Data System (ADS)

Montgomery, D. S.; Daughton, W. S.; Albright, B. J.; Wilson, D. C.; Loomis, E. N.; Merritt, E. C.; Dodd, E. S.; Kirkpatrick, R. C.; Watt, R. G.; Rosen, M. D.

2017-10-01

A goal of double shell capsule implosions is to impart sufficient internal energy to the D-T fuel at stagnation in order to obtain robust α-heating and burn with low hot spot convergence, C.R. < 10. A simple description of the kinetic energy transfer from the outer shell to the inner shell is found using shock physics and adiabatic compression, and compares well with 1D modeling. An isobaric model for the stagnation phase of the inner shell is used to determine the ideal partition of internal energy in the D-T fuel. Robust burn of the fuel requires, at minimum, that α-heating exceeds the rate of cooling by expansion of the hot spot so that the yield occurs before the hot spot disassembles, which is then used to define a minimum requirement for robust burn. One potential advantage of a double shell capsule compared to single shell capsules is the use of a heavy metal pusher, which may lead to a longer hot spot disassembly time. We present these analytic results and compare them to 1D and 2D radiation-hydrodynamic simulations. Work performed under the auspices of DOE by LANL under contract DE-AC52-06NA25396.

Animal models in burn research.

PubMed

Abdullahi, A; Amini-Nik, S; Jeschke, M G

2014-09-01

Burn injury is a severe form of trauma affecting more than 2 million people in North America each year. Burn trauma is not a single pathophysiological event but a devastating injury that causes structural and functional deficits in numerous organ systems. Due to its complexity and the involvement of multiple organs, in vitro experiments cannot capture this complexity nor address the pathophysiology. In the past two decades, a number of burn animal models have been developed to replicate the various aspects of burn injury, to elucidate the pathophysiology, and to explore potential treatment interventions. Understanding the advantages and limitations of these animal models is essential for the design and development of treatments that are clinically relevant to humans. This review aims to highlight the common animal models of burn injury in order to provide investigators with a better understanding of the benefits and limitations of these models for translational applications. While many animal models of burn exist, we limit our discussion to the skin healing of mouse, rat, and pig. Additionally, we briefly explain hypermetabolic characteristics of burn injury and the animal model utilized to study this phenomena. Finally, we discuss the economic costs associated with each of these models in order to guide decisions of choosing the appropriate animal model for burn research.

Animal Models in Burn Research

PubMed Central

Abdullahi, A.; Amini-Nik, S.; Jeschke, M.G

2014-01-01

Burn injury is a severe form of trauma affecting more than two million people in North America each year. Burn trauma is not a single pathophysiological event but a devastating injury that causes structural and functional deficits in numerous organ systems. Due to its complexity and the involvement of multiple organs, in vitro experiments cannot capture this complexity nor address the pathophysiology. In the past two decades, a number of burn animal models have been developed to replicate the various aspects of burn injury; to elucidate the pathophysiology and explore potential treatment interventions. Understanding the advantages and limitations of these animal models is essential for the design and development of treatments that are clinically relevant to humans. This review paper aims to highlight the common animal models of burn injury in order to provide investigators with a better understanding of the benefits and limitations of these models for translational applications. While many animal models of burn exist, we limit our discussion to the skin healing of mouse, rat, and pig. Additionally, we briefly explain hypermetabolic characteristics of burn injury and the animal model utilized to study this phenomena. Finally, we discuss the economic costs associated with each of these models in order to guide decisions of choosing the appropriate animal model for burn research. PMID:24714880

40 CFR 60.106 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... determine opacity. (c) If auxiliary liquid or solid fossil-fuels are burned in an incinerator-waste heat... rate from solid or liquid fossil fuel, GJ/hr (million Btu/hr). Rc = Coke burn-off rate, Mg coke/hr (ton... supplemental gaseous, liquid, or solid fossil fuel is burned, testing shall be conducted at a point between the...

40 CFR 60.106 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... determine opacity. (c) If auxiliary liquid or solid fossil-fuels are burned in an incinerator-waste heat... rate from solid or liquid fossil fuel, GJ/hr (million Btu/hr). Rc = Coke burn-off rate, Mg coke/hr (ton... supplemental gaseous, liquid, or solid fossil fuel is burned, testing shall be conducted at a point between the...

The correlation between burn mortality rates from fire and flame and economic status of countries.

PubMed

Peck, Michael; Pressman, Melissa A

2013-09-01

Over 95% of burn deaths occur in low- and middle-income countries globally. However, the association between burn mortality rates and economic health has not been evaluated for individual countries. This study seeks to answer the question, how strong is the correlation between burn mortality and national indices of economic strength? A retrospective review was performed for 189 countries during 2008-2010 using economic data from the World Bank as well as mortality data from the World Health Organization (WHO). Countries were categorized into four groups based on income level according to stratification by the World Bank: low income, lower middle income, upper middle income, and high income. The Pearson correlation coefficient was used to estimate presence and strength of association among death rates, Gini coefficient (measure of inequality of distribution of wealth), gross domestic product (GDP) per capita, and gross national index (GNI) per capita. Statistically significant associations (p<0.05) were found between burn mortality and GDP per capita (r=-0.26), GNI per capita (r=-0.36), and Gini (r=+0.17). A nation's income level is negatively correlated with burn mortality; the lower the income level, the higher the burn mortality rates. The degree to which income within a country is equitably or inequitably distributed also correlates with burn mortality. Both governmental and non-governmental organizations need to focus on preventing burns in low-income countries, as well as in other countries in which there is marked disparity of income. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Development of a Consistent and Reproducible Porcine Scald Burn Model

PubMed Central

Kempf, Margit; Kimble, Roy; Cuttle, Leila

2016-01-01

There are very few porcine burn models that replicate scald injuries similar to those encountered by children. We have developed a robust porcine burn model capable of creating reproducible scald burns for a wide range of burn conditions. The study was conducted with juvenile Large White pigs, creating replicates of burn combinations; 50°C for 1, 2, 5 and 10 minutes and 60°C, 70°C, 80°C and 90°C for 5 seconds. Visual wound examination, biopsies and Laser Doppler Imaging were performed at 1, 24 hours and at 3 and 7 days post-burn. A consistent water temperature was maintained within the scald device for long durations (49.8 ± 0.1°C when set at 50°C). The macroscopic and histologic appearance was consistent between replicates of burn conditions. For 50°C water, 10 minute duration burns showed significantly deeper tissue injury than all shorter durations at 24 hours post-burn (p ≤ 0.0001), with damage seen to increase until day 3 post-burn. For 5 second duration burns, by day 7 post-burn the 80°C and 90°C scalds had damage detected significantly deeper in the tissue than the 70°C scalds (p ≤ 0.001). A reliable and safe model of porcine scald burn injury has been successfully developed. The novel apparatus with continually refreshed water improves consistency of scald creation for long exposure times. This model allows the pathophysiology of scald burn wound creation and progression to be examined. PMID:27612153

Titanium subhydride potassium perchlorate (TiH1.65/KClO4) burn rates from hybrid closed bomb-strand burner experiments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, Marcia A.; Oliver, Michael S.

2012-08-01

A hybrid closed bomb-strand burner is used to measure the burning behavior of the titanium subhydride potassium perchlorate pyrotechnic with an equivalent hydrogen concentration of 1.65. This experimental facility allows for simultaneous measurement of the closed bomb pressure rise and pyrotechnic burn rate as detected by electrical break wires over a range of pressures. Strands were formed by pressing the pyrotechnic powders to bulk densities between 60% and 90% theoretical maximum density. The burn rate dependance on initial density and vessel pressure are measured. At all initial strand densities, the burn is observed to transition from conductive to convective burningmore » within the strand. The measured vessel pressure history is further analyzed following the closed bomb analysis methods developed for solid propellants.« less

Liquid oxygen/metal gelled monopropellants

NASA Technical Reports Server (NTRS)

Wickman, John H.

1991-01-01

The objectives of this program were to establish the feasibility of metallized/liquid oxygen monopropellants and select the best monopropellant formulation for continued study. The metal powders mixed with the liquid oxygen were aluminum/magnesium (80/20), silicon and iron (Iron was only tested for burning properties). The formulations were first evaluated on whether they detonated when ignited or burned. The formulations only burned when ignited. The viscosity for the formulations ranged from 900 cps to 100 cps at shear rates up to 300 seconds(sup -1). Two percent (by weight) of Cab-O-Sil was added to the aluminum and aluminum/magnesium formulations for gelling while the silicon formulation used three percent. Within a seven hour period, settling was suggested only in the 29 percent aluminum and 29 percent aluminum/magnesium formulations. The monopropellants were burned in a cylinder submerged in a liquid nitrogen bath. Experimental data at ambient pressure indicated that the monopropellants were extinguished when the flame front reached regions submerged under the liquid nitrogen. The burn rate increased dramatically when burned in a cylinder enclosure with less heat sink available to the monopropellant. The test results were inconclusive as to whether the increased burn rate was due to the lower heat sink capacity or the small amount of pressure (2 psi) generated during the burning of the monopropellant. The burning of the aluminum and aluminum/magnesium resulted in a brilliant white flame similar to that of an arc welder. These monopropellants burned in a pulsating manner with the aluminum/magnesium appearing to have less pulsating combustion. The silicon monopropellant burned with an orange glow. No sparks or energetic burning was apparent as with the aluminum or aluminum/magnesium.

Impacts of Brown Carbon from Biomass Burning on Surface UV and Ozone Photochemistry in the Amazon Basin

NASA Technical Reports Server (NTRS)

Mok, Jungbin; Krotkov, Nickolay A.; Arola, Antti; Torres, Omar; Jethva, Hiren; Andrade, Marcos; Labow, Gordon; Eck, Thomas F.; Li, Zhangqing; Dickerson, Russell R.;

Impacts of brown carbon from biomass burning on surface UV and ozone photochemistry in the Amazon Basin.

PubMed

Mok, Jungbin; Krotkov, Nickolay A; Arola, Antti; Torres, Omar; Jethva, Hiren; Andrade, Marcos; Labow, Gordon; Eck, Thomas F; Li, Zhanqing; Dickerson, Russell R; Stenchikov, Georgiy L; Osipov, Sergey; Ren, Xinrong

2016-11-11

The spectral dependence of light absorption by atmospheric particulate matter has major implications for air quality and climate forcing, but remains uncertain especially in tropical areas with extensive biomass burning. In the September-October 2007 biomass-burning season in Santa Cruz, Bolivia, we studied light absorbing (chromophoric) organic or "brown" carbon (BrC) with surface and space-based remote sensing. We found that BrC has negligible absorption at visible wavelengths, but significant absorption and strong spectral dependence at UV wavelengths. Using the ground-based inversion of column effective imaginary refractive index in the range 305-368 nm, we quantified a strong spectral dependence of absorption by BrC in the UV and diminished ultraviolet B (UV-B) radiation reaching the surface. Reduced UV-B means less erythema, plant damage, and slower photolysis rates. We use a photochemical box model to show that relative to black carbon (BC) alone, the combined optical properties of BrC and BC slow the net rate of production of ozone by up to 18% and lead to reduced concentrations of radicals OH, HO 2 , and RO 2 by up to 17%, 15%, and 14%, respectively. The optical properties of BrC aerosol change in subtle ways the generally adverse effects of smoke from biomass burning.

Evaluating the role of alternative therapy in burn wound management: randomized trial comparing moist exposed burn ointment with conventional methods in the management of patients with second-degree burns.

PubMed

Ang, E S; Lee, S T; Gan, C S; See, P G; Chan, Y H; Ng, L H; Machin, D

2001-03-06

Moist exposed burn ointment (MEBO), from China, has been said to revolutionize burn management. Our study was conducted to compare MEBO with conventional management (C) with respect to the rate of wound healing, antibacterial and analgesic effect, and hospital costs. This is a prospective, randomized, controlled clinical trial conducted between 1 March 1997 and 24 October 1998. The trial was conducted in a specialized burn facility located in a tertiary referral hospital in a developed and industrialized island-state in Southeast Asia. We randomly assigned 115 consecutive patients between the ages of 12 and 80 who had partial-thickness thermal burns covering less than 40% of body surface area (BSA) to receive either MEBO or C. Fifty-seven patients were assigned to MEBO and 58 patients to C. The latter group received twice-daily dressing changes; MEBO patients received MEBO every 4 hours. Patients were hospitalized until 75% BSA had healed. BSA was determined by visual inspection and charted on Lund and Browder charts regularly. Wound healing rate, bacterial infection rate, pain score, and hospitalization costs were recorded. The median time to 75% healing was 17.0 and 20.0 days with MEBO and C, respectively (HR = 0.67, 95% CI = 0.41-1.11, P =.11), suggesting similar efficacy between the 2 modalities. Bacterial infection rates were similar between the 2 groups (HR = 1.10, 95% CI = 0.59-2.03, P =.76). MEBO imparted a greater analgesic effect in the first 5 days of therapy and reduced hospital costs by 8%. MEBO is as effective as conventional management but is not the panacea for all burn wounds. The use of MEBO eases the management of face and neck burns and facilitates early institution of occupational therapy in hand burns. It confers better pain relief such that fewer opiates are used during the first 5 days after burn injury.

Safety and efficacy of excision and direct closure in acute burns surgery: outcome analysis in a prospective series of 100 patients and a survey of UK burns surgeons' attitudes.

PubMed

Bain, Charles J; Wang, Tim; McArthur, Gordon; Williams, Greg; Atkins, Joanne; Jones, Isabel

2014-12-01

Many burns surgeons avoid excision and direct closure of acute burns owing to concerns over wound dehiscence, scarring and infection. There is no evidence in the literature to support this practice. We present outcomes of a prospective series of 100 patients who underwent excision and direct closure of 138 burns over a 2-year period, along with results from a survey sent to 33 senior burns surgeons to gauge attitudes towards direct closure in burns surgery. 47% of survey respondents never perform direct closure. Dehiscence was cited as the most common concern, followed by hypertrophic scarring (HTS). In our cohort, the superficial dehiscence rate was 12% and the HTS rate was 16%, with no scarring contractures. Patients with healing time greater than 14 days were more likely to develop HTS (p=0.008), as were those with wound dehiscence (p=0.014). Patients undergoing part-grafting in addition to direct closure took significantly longer to heal than those undergoing direct closure alone (p=0.0002), with the donor site or graft delaying healing in the majority. Excision and direct closure of acute burn wounds avoids donor site morbidity and has an acceptable complication rate. It is a safe and effective treatment for full thickness burns in selected cases. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Organic aerosol evaporation and formation in biomass-burning plumes: The competition between dilution and chemistry

NASA Astrophysics Data System (ADS)

Pierce, J. R.; Kreidenweis, S. M.; Bian, Q.; Jathar, S.; Kodros, J.; Barsanti, K.; Hatch, L. E.; May, A.

2017-12-01

Secondary organic aerosol (SOA) has been shown to form in biomass-burning emissions in laboratory and field studies. However, there is significant variability among studies in mass enhancement, which could be due to differences in fuels, fire conditions, dilution, and/or limitations of laboratory experiments and observations. This study focuses on understanding processes affecting biomass-burning SOA formation in ambient plumes. The plume dilution rate impacts the organic partitioning between the gas and particle phases, which may impact the potential for SOA to form as well as the rate of SOA formation. We use an aerosol microphysics model that includes representations of volatility and oxidation chemistry to estimate SOA formation in the smoke emitted into the atmosphere. We add Gaussian dispersion to our aerosol microphysical model to estimate how SOA formation may vary under different ambient-plume conditions (e.g. fire size, emission mass flux, atmospheric stability). Smoke from small fires, such as typical prescribed burns, dilutes rapidly, which drives evaporation of organic vapor from the particle phase, leading to more effective SOA formation. Emissions from large fires, such as intense wildfires, dilute slowly, suppressing OA evaporation and subsequent SOA formation in the near field. We also demonstrate that different approaches to the calculation of OA enhancement in ambient plumes can lead to different conclusions regarding SOA formation. Normalized OA mass enhancement ratios of around 1 calculated using an inert tracer, such as black carbon or CO, have traditionally been interpreted as exhibiting little or no SOA formation; however, we show that SOA formation may have greatly contributed to the mass in these plumes.

Standardization of deep partial-thickness scald burns in C57BL/6 mice

PubMed Central

Medina, Jorge L; Fourcaudot, Andrea B; Sebastian, Eliza A; Shankar, Ravi; Brown, Ammon W; Leung, Kai P

2018-01-01

Mouse burn models are used to understand the wound healing process and having a reproducible model is important. The different protocols used by researchers can lead to differences in depth of partial-thickness burn wounds. Additionally, standardizing a protocol for mouse burns in the laboratory for one strain may result in substantially different results in other strains. In our current study we describe the model development of a deep partial-thickness burn in C57BL/6 mice using hot water scalding as the source of thermal injury. As part of our model development we designed a template with specifications to allow for even contact of bare mouse skin (2×3 cm) with hot water while protecting the rest of the mouse. Burn depth was evaluated with H&E, Masson’s trichrome, and TUNEL staining. Final results were validated with pathology analysis. A water temperature of 54°C with a scalding time of 20 seconds produced consistent deep partial-thickness burns with available equipment described. Other than temperature and time, factors such as template materials and cooling steps after the burn could affect the uniformity of the burns. These findings are useful to burn research by providing some key parameters essential for researchers to simplify the development of their own mouse burn models. PMID:29755839

The investigation of critical burning of fuel droplets

NASA Technical Reports Server (NTRS)

Allison, C. B.; Canada, G. S.; Faeth, G. M.

1973-01-01

The combustion and evaporation of liquid fuels at high pressures were investigated. Particular emphasis was placed on conditions where the liquid surface approaches the thermodynamic critical point during combustion. The influence of transient effects on a burning liquid fuel was also investigated through both analysis and measurements of the response of liquid monopropellant combustion to imposed pressure oscillations. Work was divided into four phases (1) Droplet combustion at high pressures, which consider both measurement and analysis of the porous sphere burning rate of liquids in a natural convection environment at elevated pressure. (2) High pressure droplet burning in combustion gases, which involved steady burning and evaporation of liquids from porous spheres in a high pressure environment that simulates actual combustion chamber conditions. (3) Liquid strand combustion, which considered the burning rate, the state of the liquid surface and the liquid phase temperature distribution of a burning liquid monopropellant column over a range of pressures. (4) Oscillatory combustion, which was a theoretical and experimental investigation of the response of a burning liquid monopropellant to pressure oscillations.

Assault by burning in Jordan.

PubMed

Haddadin, W

2012-12-31

Criminal attacks by burns on women in Jordan are highlighted in this retrospective study carried out of all proved cases of criminal burns in female patients treated at the burn unit of the Royal Rehabilitation Center in Jordan between January 2005 and June 2012. Thirteen patients were included in our study, out of a total of 550 patients admitted, all in the age range of 16-45 yr. Of these 13 women, six were burned by acid throwing, five by hot water, and two by direct flames from fuel thrown over them. Burn percentage ranged from 15 to 75% of the total body surface area, with involvement in most cases of the face and upper trunk. The mean hospital stay was 33 days and the mortality rate was 3/13, i.e. 23%. Violence against women exists in Jordanian society, yet burning assaults are rare. Of these, burning by throwing acid is the most common and most disfiguring act, with a higher mortality rate in domestic environments.

Assault by burning in Jordan

PubMed Central

Haddadin, W.

2012-01-01

Summary Criminal attacks by burns on women in Jordan are highlighted in this retrospective study carried out of all proved cases of criminal burns in female patients treated at the burn unit of the Royal Rehabilitation Center in Jordan between January 2005 and June 2012. Thirteen patients were included in our study, out of a total of 550 patients admitted, all in the age range of 16-45 yr. Of these 13 women, six were burned by acid throwing, five by hot water, and two by direct flames from fuel thrown over them. Burn percentage ranged from 15 to 75% of the total body surface area, with involvement in most cases of the face and upper trunk. The mean hospital stay was 33 days and the mortality rate was 3/13, i.e. 23%. Violence against women exists in Jordanian society, yet burning assaults are rare. Of these, burning by throwing acid is the most common and most disfiguring act, with a higher mortality rate in domestic environments. PMID:23766757

40 CFR 63.6590 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2012 CFR

2012-07-01

... initial notification requirements: (i) Existing spark ignition 2 stroke lean burn (2SLB) stationary RICE... spark ignition 4 stroke lean burn (4SLB) stationary RICE with a site rating of more than 500 brake HP... spark ignition 4 stroke rich burn (4SRB) stationary RICE with a site rating of less than or equal to 500...

A mathematical model for predicting fire spread in wildland fuels

Treesearch

Richard C. Rothermel

1972-01-01

A mathematical fire model for predicting rate of spread and intensity that is applicable to a wide range of wildland fuels and environment is presented. Methods of incorporating mixtures of fuel sizes are introduced by weighting input parameters by surface area. The input parameters do not require a prior knowledge of the burning characteristics of the fuel.

Ignition and Combustion Studies of Hazard Division 1.1 and 1.3 Substances

DTIC Science & Technology

2010-07-01

Effect of Time at Temperature on Burning Rate. The burning rate of the HD1.1 explosive PBXN -5 is compared to that of neat cyclotetramethylene...tetranitramine (HMX) in Figure 14. The explosive, PBXN -5, is composed of 95 weight percent HMX and 5 percent Viton A as binder. The HMX burning rate...the closed bomb technique (Reference 18). The PBXN -5 was composed of small agglomerates of HMX coated with the binder (Reference 19). The PBXN -5

Combustion in an acceleration field: A survey of Soviet literature

NASA Technical Reports Server (NTRS)

Radloff, S. J.; Osborn, J. R.

1980-01-01

The effect of an acceleration field on the burning rate of a solid propellant was measured from -900g's to +1000g's using both double base and ammonium perchlorate based propellants. The acceleration fields were simulated using a centrifuge device and the burning rate was recorded. Both metalized and non-metalized variations of each propellant were tested and it was found that acceleration fields affect the burning rate. For the most part the theoretical predictions and the experimental results agreed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menikoff, Ralph

Previously the SURFplus reactive burn model was calibrated for the TATB based explosive PBX 9502. The calibration was based on fitting Pop plot data, the failure diameter and the limiting detonation speed, and curvature effect data for small curvature. The model failure diameter is determined utilizing 2-D simulations of an unconfined rate stick to find the minimum diameter for which a detonation wave propagates. Here we examine the effect of mesh resolution on an unconfined rate stick with a diameter (10mm) slightly greater than the measured failure diameter (8 to 9 mm).

Combustion of Interacting Droplet Arrays in a Microgravity Environment

NASA Technical Reports Server (NTRS)

Dietrich, D. L.; Struk, P. M.; Kitano, K.; Ikegami, M.

1999-01-01

Investigations into droplet interactions date back to Rex et al. Recently, Annamalai and Ryan and Annamalai published extensive reviews of droplet array and cloud combustion studies. The authors studied the change in the burning rate constant, k, (relative to that of the single droplet) that results from interactions. Under certain conditions, there exists a separation distance where the droplet lifetime reaches a minimum, or average burning rate constant is a maximum . Additionally, since inter-droplet separation distance, L, increases relative to the droplet size, D, as the burning proceeds, the burning rate is not constant throughout the burn, but changes continuously with time. Only Law and co-workers and Mikami et al. studied interactions under conditions where buoyant forces were negligible. Comparing their results with existing theory, Law and co-workers found that theory over predicted the persistency and intensity of droplet interactions. The droplet interactions also depended on the initial array configuration as well as the instantaneous array configuration. They also concluded that droplet heating was retarded due to interactions and that the burning process did not follow the "D-squared" law. Mikami et al. studied the combustion of a two-droplet array of heptane burning in air at one atm pressure in microgravity. They showed that the instantaneous burning rate constant increases throughout the droplet lifetime, even for a single droplet. Also, the burn time of the array reached a minimum at a critical inter-droplet spacing. In this article, we examine droplet interactions in normal and microgravity environments. The microgravity experiments were in the NASA GRC 2.2 and 5.2 second drop towers, and the JAMIC (Japan Microgravity Center) 10 second drop tower. Special emphasis is directed to combustion under conditions that yield finite extinction diameters, and to determine how droplet interactions affect the extinction process.

Influence of fuel mass load, oxygen supply and burning rate on emission factor and size distribution of carbonaceous particulate matter from indoor corn straw burning.

PubMed

Shen, Guofeng; Xue, Miao; Wei, Siye; Chen, Yuanchen; Wang, Bin; Wang, Rong; Shen, Huizhong; Li, Wei; Zhang, Yanyan; Huang, Ye; Chen, Han; Wei, Wen; Zhao, Qiuyue; Li, Bin; Wu, Haisuo; Tao, Shu

2013-03-01

The uncertainty in emission estimation is strongly associated with the variation in emission factor (EF), which could be influenced by a variety of factors such as fuel properties, stove type, fire management and even methods used in measurements. The impacts of these factors are complicated and often interact with each other. Controlled burning experiments were conducted to investigate the influences of fuel mass load, air supply and burning rate on the emissions and size distributions of carbonaceous particulate matter (PM) from indoor corn straw burning in a cooking stove. The results showed that the EFs of PM (EF(PM)), organic carbon (EFoc) and elemental carbon (EF(EC)) were independent of the fuel mass load. The differences among them under different burning rates or air supply amounts were also found to be insignificant (p > 0.05) in the tested circumstances. PM from the indoor corn straw burning was dominated by fine PM with diameter less than 2.1 microm, contributing 86.4% +/- 3.9% of the total. The size distribution of PM was influenced by the burning rate and air supply conditions. On average, EF(PM), EF(OC) and EF(EC) for corn straw burned in a residential cooking stove were (3.84 +/- 1.02), (0.846 +/- 0.895) and (0.391 +/- 0.350) g/kg, respectively. EF(PM), EF(OC) and EF(EC) were found to be positively correlated with each other (p < 0.05), but they were not significantly correlated with the EF of co-emitted CO, suggesting that special attention should be paid to the use of CO as a surrogate for other incomplete combustion pollutants.

The influence of fuel mass load, oxygen supply and burning rate on emission factor and size distribution of carbonaceous particulate matter from indoor corn straw burning

PubMed Central

Shen, Guofeng; Xue, Miao; Wei, Siye; Chen, Yuanchen; Wang, Bing; Wang, Rong; Shen, Huizhong; Li, Wei; Zhang, Yanyan; Huang, Ye; Chen, Han; Wei, Wen; Zhao, Qiuyue; Li, Bin; Wu, Haisuo; Tao, Shu

2014-01-01

The uncertainty in emission estimation is strongly associated with the variation in emission factor which could be influenced by a variety of factors, like fuel property, stove type, fire management and even methods used in measurements. The impacts of these factors were usually complicated and often interacted with each other. In the present study, controlled burning experiments were conducted to investigate the influence of fuel mass load, air supply and burning rate on the emission of carbonaceous particulate matter (PM) from indoor corn straw burning. Their impacts on PM size distribution were also studied. The results showed that EFs of PM (EFPM), organic carbon (EFOC) and element carbon (EFEC) was independent of the fuel mass load. The differences among them under different burning rates or air supply amounts were also found to be insignificant (p > 0.05) in the tested circumstances. PM from the indoor corn straw burning was dominated by fine PM, and PM with diameter less than 2.1 μm contributed about 86.4±3.9% of the total. The size distribution of PM was also influenced by the burning rate and changed air supply conditions. On average, EFPM, EFOC and EFEC for corn straw burned in a residential cooking stove were 3.84±1.02, 0.846±0.895 and 0.391±0.350 g/kg, respectively. EFPM, EFOC and EFEC were found to be positively correlated with each other, but they were not significantly correlated with EF of co-emitted CO, suggesting a special attention should be paid to the use of CO acting as a surrogate for other incomplete pollutants. PMID:23923424

Turbulent flame propagation and combustion in spark ignition engines

NASA Technical Reports Server (NTRS)

Beretta, G. P.; Rashidi, M.; Keck, J. C.

1983-01-01

Pressure measurements synchronized with high-speed motion-picture records of flame propagation have been made in a transparent-piston engine. The data show that the initial expansion speed of the flame front is close to that of a laminar flame. As the flame expands, its speed rapidly accelerates to a quasi-steady value comparable with that of the turbulent velocity fluctuations in the unburned gas. During the quasi-steady propagation phase, a significant fraction of the gas behind the visible front is unburned. Final burnout of the charge may be approximated by an exponential decay in time. The data have been analyzed in a model-independent way to obtain a set of empirical equations for calculating mass burning rates in spark-ignition engines. The burning equations contain three parameters: the laminar burning speed, a characteristic speed (uT), and a characteristic length (lT). The laminar burning speed is known from laboratory measurements. Tentative correlations relating uT and lT to engine geometry and operating variables have been derived from the engine data.

The effect of azeotropism on combustion characteristics of blended fuel pool fire.

PubMed

Ding, Yanming; Wang, Changjian; Lu, Shouxiang

2014-04-30

The effect of azeotropism on combustion characteristics of blended fuel pool fire was experimentally studied in an open fire test space of State Key Laboratory of Fire Science. A 30 cm × 30 cm square pool filled with n-heptane and ethanol blended fuel was employed. Flame images, burning rate and temperature distribution were collected and recorded in the whole combustion process. Results show that azeotropism obviously dominates the combustion behavior of n-heptane/ethanol blended fuel pool fire. The combustion process after ignition exhibits four typical stages: initial development, azeotropic burning, single-component burning and decay stage. Azeotropism appears when temperature of fuel surface reaches azeotropic point and blended fuel burns at azeotropic ratio. Compared with individual pure fuel, the effect of azeotropism on main fire parameters, such as flame height, burning rate, flame puffing frequency and centerline temperature were analyzed. Burning rate and centerline temperature of blended fuel are higher than that of individual pure fuel respectively at azeotropic burning stage, and flame puffing frequency follows the empirical formula between Strouhal and Froude number for pure fuel. Copyright © 2014 Elsevier B.V. All rights reserved.

Biomass Burning, Land-Cover Change, and the Hydrological Cycle in Northern Sub-Saharan Africa

NASA Technical Reports Server (NTRS)

Ichoku, Charles; Ellison, Luke T.; Willmot, K. Elena; Matsui, Toshihisa; Dezfuli, Amin K.; Gatebe, Charles K.; Wang, Jun; Wilcox, Eric M.; Lee, Jejung; Adegoke, Jimmy;

Erosive Burning Study Utilizing Ultrasonic Measurement Techniques

NASA Technical Reports Server (NTRS)

Furfaro, James A.

2003-01-01

A 6-segment subscale motor was developed to generate a range of internal environments from which multiple propellants could be characterized for erosive burning. The motor test bed was designed to provide a high Mach number, high mass flux environment. Propellant regression rates were monitored for each segment utilizing ultrasonic measurement techniques. These data were obtained for three propellants RSRM, ETM- 03, and Castor@ IVA, which span two propellant types, PBAN (polybutadiene acrylonitrile) and HTPB (hydroxyl terminated polybutadiene). The characterization of these propellants indicates a remarkably similar erosive burning response to the induced flow environment. Propellant burnrates for each type had a conventional response with respect to pressure up to a bulk flow velocity threshold. Each propellant, however, had a unique threshold at which it would experience an increase in observed propellant burn rate. Above the observed threshold each propellant again demonstrated a similar enhanced burn rate response corresponding to the local flow environment.

Quantifying soil burn severity for hydrologic modeling to assess post-fire effects on sediment delivery

NASA Astrophysics Data System (ADS)

Dobre, Mariana; Brooks, Erin; Lew, Roger; Kolden, Crystal; Quinn, Dylan; Elliot, William; Robichaud, Pete

2017-04-01

Soil erosion is a secondary fire effect with great implications for many ecosystem resources. Depending on the burn severity, topography, and the weather immediately after the fire, soil erosion can impact municipal water supplies, degrade water quality, and reduce reservoirs' storage capacity. Scientists and managers use field and remotely sensed data to quickly assess post-fire burn severity in ecologically-sensitive areas. From these assessments, mitigation activities are implemented to minimize post-fire flood and soil erosion and to facilitate post-fire vegetation recovery. Alternatively, land managers can use fire behavior and spread models (e.g. FlamMap, FARSITE, FOFEM, or CONSUME) to identify sensitive areas a priori, and apply strategies such as fuel reduction treatments to proactively minimize the risk of wildfire spread and increased burn severity. There is a growing interest in linking fire behavior and spread models with hydrology-based soil erosion models to provide site-specific assessment of mitigation treatments on post-fire runoff and erosion. The challenge remains, however, that many burn severity mapping and modeling products quantify vegetation loss rather than measuring soil burn severity. Wildfire burn severity is spatially heterogeneous and depends on the pre-fire vegetation cover, fuel load, topography, and weather. Severities also differ depending on the variable of interest (e.g. soil, vegetation). In the United States, Burned Area Reflectance Classification (BARC) maps, derived from Landsat satellite images, are used as an initial burn severity assessment. BARC maps are classified from either a Normalized Burn Ratio (NBR) or differenced Normalized Burned Ratio (dNBR) scene into four classes (Unburned, Low, Moderate, and High severity). The development of soil burn severity maps requires further manual field validation efforts to transform the BARC maps into a product more applicable for post-fire soil rehabilitation activities. Alternative spectral indices and modeled output approaches may prove better predictors of soil burn severity and hydrologic effects, but these have not yet been assessed in a model framework. In this project we compare field-verified soil burn severity maps to satellite-derived and modeled burn severity maps. We quantify the extent to which there are systematic differences in these mapping products. We then use the Water Erosion Prediction Project (WEPP) hydrologic soil erosion model to assess sediment delivery from these fires using the predicted and observed soil burn severity maps. Finally, we discuss differences in observed and predicted soil burn severity maps and application to watersheds in the Pacific Northwest to estimate post-fire sediment delivery.

[Clinical observation of the effects of FE combined enzymes on the infection of the granulation burn wound during late post burns stage].

PubMed

Zheng, Ji; Liu, Xu-sheng; Huang, Yue-sheng; Liu, Chun-yu

2006-02-01

To observe the effects of combined FE enzymes on the infection of the granulation burn wound during late postburn stage in controlling burn wound infection caused by common antibiotic resistant bacteria. Thirty patients in our burn ward were enrolled and were randomly divided into A [treated with combined FE enzymes (50 ml dissolved in 0-150 ml normal saline to reach the final concentration of 1-3 U/ml)] and B (treated with gentamicin) groups, with 15 patients in each group. Several layers of gauze, either soaked with combined FE enzyme in A or gentamicin in B group, were used to cover the burn wounds once to twice a day. Bacterial culture from the burn wound exudation before and after drug administration was done before the application of the agents. The bacteria in the burn wounds and their susceptibility to antibiotics were identified. The healing time of the burn wounds was recorded. Furthermore, the healing rate of the burn wound was recorded on the 3rd, 5th, 8th, 10th and 12th post skin grafting days (PSGD). The dominating bacteria in the burn wounds in both groups were Pseudomonas aeruginosa, Escherichia coli, Enterobacter cloacae and MRSA. The susceptibility rate of bacteria ( MRSA, Staphylococcus epidermidis, Staphylococcus saprophyte, Pseudomonas aeruginosa, Escherichia coli and Enterobacter cloacae) to combined FE enzyme was 93.8%, 100.0%, 100.0%, 100.0%, 100.0% and 95.0% respectively, which were much higher than those in B group (17.6%, 31.3%, 28.6%, 44.0%, 33.3%, 28.0% respectively, P < 0.1. The wound healing time after skin grafting in A group (10.6 +/- 1.5 days) was significantly shorter than that in B group (15.3 +/- 1.7 days, P < 0.01). The wound healing rate on 10 PSGD in A group was (85.4 +/- 2.4)%, and which was only (51.3 +/- 1.5% in B group (P < 0.01) Combined FE enzyme can effectively control burn wound infection, so that the interval between skin grafting and wound healing can be shortened and success rate of skin grafting be improved.

Application of the cultured epidermal autograft "JACE(®") for treatment of severe burns: Results of a 6-year multicenter surveillance in Japan.

PubMed

Matsumura, Hajime; Matsushima, Asako; Ueyama, Masashi; Kumagai, Norio

2016-06-01

In the 1970s, Green et al. developed a method that involved culturing keratinocyte sheets and used for treatment of burns. Since then, the take rate of cultured epidermal autograft (CEA) onto fascia, granulation tissue, or allografts has been extensively reported, while that on an artificial dermis in a large case series is not. Moreover, the contribution of CEA to patient survival has not been analyzed in a multicenter study. We conducted a 6-year multicenter surveillance on the application of the CEA "JACE(®") for treatment of burns >30% total body surface area (TBSA) across 118 Japanese hospitals. This surveillance included 216 patients and 718 graft sites for efficacy analysis. The CEA take rate at 4 weeks after grafting was evaluated, and safety was monitored until 52 weeks. In addition, the survival curve obtained in this study and the data obtained from the Tokyo Burn Unit Association (TBUA) were compared. The mean CEA take rates at week 4 were 66% (sites) and 68% (patients), and the rate on the artificial dermis was 65% for 226 sites. CEA application combined with wide split-thickness auto or patch autograft increased the CEA take rate. On comparison with the data obtained from the TBUA, which included data on individuals with burns of the same severity, CEA application was found to contribute to patient survival until 7 weeks after burn. We reported the take rate of CEA based on a 6-year multicenter surveillance. From our results, we found that the application of CEA is a useful treatment for the patients with extensive burns. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Probing thermonuclear burning on accreting neutron stars

NASA Astrophysics Data System (ADS)

Keek, L.

2008-12-01

Neutron stars are the most compact stars that can be directly observed, which makes them ideal laboratories to study physics at extreme densities. Neutron stars in low-mass X-ray binaries accrete hydrogen and helium from a lower-mass companion star through Roche lobe overflow. This matter undergoes thermonuclear burning in the neutron star envelope, creating carbon and heavier elements. The fusion process may proceed in an unstable manner, resulting in a thermonuclear runaway. Within one second the entire surface is burned, which is observable as a sharp rise in the emitted X-ray flux: a type I X-ray burst. Afterwards the neutron star surface cools down on a timescale of ten to one hundred seconds. During these bursts the surface of an accreting neutron star can be observed directly, which makes them instrumental for studying this type of stars. We have studied rare kinds of X-ray bursts. One such rare burst is the superburst, which lasts a thousand times longer than an ordinary burst. Superbursts are thought to result from the explosive burning of a thick carbon layer, which lies deeper inside the neutron star, close to a layer known as the crust. A prerequisite for the occurrence of a superburst is a high enough temperature, which is set by the temperature of the crust and the heat conductivity of the envelope. The latter is lowered by the presence of heavy elements that are produced during normal X-ray bursts. Using a large set of observations from the Wide Field Camera's onboard the BeppoSAX satellite, we find that, at high accretion rate, sources which do not exhibit normal bursts likely have a longer superburst recurrence time, than the observed superburst recurrence time of one burster. We analyze in detail the first superburst from a transient source, which went into outburst only 55 days before the superburst. Recent models of the neutron star crust predict that this is too small a time to heat the crust sufficiently for superburst ignition, indicating that the models need to be extended with a new heat source. Another rare phenomenon is the occurrence of bursts with recurrence times of less than 30 minutes. In a long set of observations of the source EXO 0748-676 we find for the first time triple bursts, where three bursts occur within 30 minutes. This time is too short to accrete new fuel for the next burst, which suggests that not all hydrogen and helium is burned during the first burst. Finally, using a hydrodynamic stellar evolution code we create a multi-zone numerical model of the neutron star envelope. For the first time we include mixing due to rotation and a rotationally induced magnetic field. We find that thermonuclear burning proceeds in a stable manner at a lower heat flux of the crust for models including mixing. This may explain the observed transition of stable to unstable burning at a lower mass accretion rate than models previously predicted.

The measured effect magnitude of co-morbidities on burn injury mortality.

PubMed

Knowlin, Laquanda; Stanford, Lindsay; Moore, Danier; Cairns, Bruce; Charles, Anthony

2016-11-01

The ability to better prognosticate burn injury outcome is challenging and historically, most center use the Baux or revised Baux score to help prognosticate burn outcome, however, the weighted contribution of comorbidity on burn mortality has traditionally not been accounted for nor adequately studied. We therefore sought to determine the effect of comorbidities, using the Charlson comorbidity index (CCI) on burn mortality. The purpose of this study was to determine the effect of comorbidities on burn injury mortality as determined by the LA50 (lethal TBSA burn at which 50% of the cohort will succumb from the burn injury) in a retrospective analysis of patients admitted to a regional burn center from 2002 to 2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA (total body surface area), length of hospital stay, and pre-existing comorbidities. Bivariate analysis was performed and logistic regression modeling using significant variables was utilized to estimate odds of death. 7640 patients were included in this study. Overall survival rate was 96%. 40% of our burn cohort had at least one comorbidity. There was a linear increase in the likelihood of death with an increase in CCI. The logistic regression model for mortality outcomes identified four statistically significant variables: age, TBSA, inhalational injury and the presence of comorbidities (OR=1.59 for each 1 point increase in CCI; 95% CI 1.44-1.77). The unadjusted LA50 was 53% for the entire cohort. Partial adjustment multivariate regression controlling for burn mechanism and inhalation injury only, produced a slight reduction in LA50 for the 0-18 and 19-64 age categories to 76% and 48% TBSA, respectively, but a significant decrease occurred in the ≥65 years age group with a reduced LA50 to 20% TBSA (p<0.001). After full adjustment for all significant covariates, including comorbidities, the independent magnitude of effect of comorbidities on the LA50 was evident in the <65 cohort. The full adjustment showed a LA50 decreased to 61% and 43% TBSA, respectively in the 0-18 and >18-65 age groups respectively (p<0.001), however, in the >65 years age cohort there was no change in the LA50. Preexisting comorbidities have a significant effect on burn injury mortality in all age groups, particularly the younger burn population. The measured effect of comorbidities in the >65 yr age cohort was mitigated by the co-linearity between age and comorbidities. The inclusion of CCI is imperative so as to better prognosticate burn outcome and help guide expectations and resource utilization, particularly in the younger burn cohort. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

The Measured Effect Magnitude of Co-Morbidities on Burn injury Mortality

PubMed Central

Knowlin, Laquanda; Stanford, Lindsay; Moore, Danier; Cairns, Bruce; Charles, Anthony

2016-01-01

Introduction The ability to better prognosticate burn injury outcome is challenging and historically, most center use the Baux or revised Baux score to help prognosticate burn outcome, however, the weighted contribution of comorbidity on burn mortality has traditionally not been accounted for nor adequately studied. We therefore sought to determine the effect of comorbidities, using the Charlson comorbidity index (CCI) on burn mortality. Methods The purpose of this study was to determine the effect of comorbidities on burn injury mortality as determined by the LA50 (lethal TBSA burn at which 50% of the cohort will succumb from the burn injury) in a retrospective analysis of patients admitted to a regional burn center from 2002–2012. Independent variables analyzed included basic demographics, burn mechanism, presence of inhalation injury, TBSA (total body surface area), length of hospital stay, and pre-existing comorbidities. Bivariate analysis was performed and logistic regression modeling using significant variables was utilized to estimate odds of death. Results 7640 patients were included in this study. Overall survival rate was 96%. 40% of our burn cohort had at least one comorbidity. There was a linear increase in the likelihood of death with an increase in CCI. The logistic regression model for mortality outcomes identified four statistically significant variables: age, TBSA, inhalational injury and the presence of comorbidities (OR = 1.59 for each 1 point increase in CCI; 95% CI 1.44–1.77). The unadjusted LA50 was 53% for the entire cohort. Partial adjustment multivariate regression controlling for burn mechanism and inhalation injury only, produced a slight reduction in LA50 for the 0–18 and 19–64 age categories to 76% and 48%, respectively, but a significant decrease occurred in the ≥ 65 years age group with a reduced LA50 to 20% (p<0.001). After full adjustment for all significant covariates, including comorbidities, the independent magnitude of effect of comorbidities on the LA50 was evident in the <65 cohort. The full adjustment showed a LA50 decreased by 15 and 5%, respectively in the 0–18 and >18–65 age groups respectively (p<0.001), however, in the >65 years age cohort there was no change in the LA50. Conclusion Preexisting comorbidities have a significant effect on burn injury mortality in all age groups, particularly the younger burn population. The measured effect of comorbidities in the >65yr age cohort was mitigated by the co-linearity between age and comorbidities. The inclusion of CCI is imperative so as to better prognosticate burn outcome and help guide expectations and resource utilization, particularly in the younger burn cohort.. PMID:27593340

Prediction of Maximal Aerobic Capacity in Severely Burned Children

PubMed Central

Porro, Laura; Rivero, Haidy G.; Gonzalez, Dante; Tan, Alai; Herndon, David N.; Suman, Oscar E.

2011-01-01

Introduction Maximal oxygen uptake (VO2 peak) is an indicator of cardiorespiratory fitness, but requires expensive equipment and a relatively high technical skill level. Purpose The aim of this study is to provide a formula for estimating VO2 peak in burned children, using information obtained without expensive equipment. Methods Children, with ≥40% total surface area burned (TBSA), underwent a modified Bruce treadmill test to asses VO2 peak at 6 months after injury. We recorded gender, age, %TBSA, %3rd degree burn, height, weight, treadmill time, maximal speed, maximal grade, and peak heart rate, and applied McHenry’s select algorithm to extract important independent variables and Robust multiple regression to establish prediction equations. Results 42 children; 7 to 17 years old were tested. Robust multiple regression model provided the equation: VO2=10.33 – 0.62 *Age (years) + 1.88 * Treadmill Time (min) + 2.3 (gender; Females = 0, Males = 1). The correlation between measured and estimated VO2 peak was R=0.80. We then validated the equation with a group of 33 burned children, which yielded a correlation between measured and estimated VO2 peak of R=0.79. Conclusions Using only a treadmill and easily gathered information, VO2 peak can be estimated in children with burns. PMID:21316155

Sources, Transport, and Climate Impacts of Biomass Burning Aerosols

NASA Technical Reports Server (NTRS)

Chin, Mian

2010-01-01

In this presentation, I will first talk about fundamentals of modeling of biomass burning emissions of aerosols, then show the results of GOCART model simulated biomass burning aerosols. I will compare the model results with observations of satellite and ground-based network in terms of total aerosol optical depth, aerosol absorption optical depth, and vertical distributions. Finally the long-range transport of biomass burning aerosols and the climate effects will be addressed. I will also discuss the uncertainties associated with modeling and observations of biomass burning aerosols

Rates of post-fire vegetation recovery and fuel accumulation as a function of burn severity and time-since-burn in four western U.S. ecosystems

USDA-ARS?s Scientific Manuscript database

Vegetation recovery and fuel accumulation rates following wildfire are useful measures of ecosystem resilience, yet few studies have quantified these variables over 10 years post-fire. Conventional wisdom is that recovery time to pre-fire condition will be slower as a function of burn severity, as i...

Effect of pressure on rate of burning /decomposition with flame/ of liquid hydrazine.

NASA Technical Reports Server (NTRS)

Antoine, A. C.

1966-01-01

Liquid hydrazine decomposition process to determine what chemical or physical changes may be occurring that cause breaks in burning rate/ pressure curves, measuring flame temperature and light emission

The conductive propagation of nuclear flames. 2: Convectively bounded flames in C + O and O + Ne + Mg cores

NASA Technical Reports Server (NTRS)

Timmes, F. X.; Woosley, S. E.; Taam, Ronald E.

1994-01-01

We determine the speeds, and many other physical properties, of flame fronts that propagate inward into degenerate and semidegenerate cores of carbon and oxygen (CO) and neon and oxygen (NeOMg) white dwarfs when such flames are bounded on their exterior by a convective region. Combustion in such fronts, per se, is incomplete, with only a small part of the initial mass function burned. A condition of balanced power is set up in the star where the rate of energy emitted as neutrinos from the convective region equals the power available from the unburned fuel that crosses the burning front. The propagation of the burning front itself is in turn limited by the temperature at the base of the convective shell, while cannot greatly exceed the adiabatic value. Solving for consistency between these two conditions gives a unique speed for the flame. Typical values for CO white dwarfs are a few hundredths of a centimeter per second. Flames in NeOMg mixtures are slower. Tables are presented in a form that can easily be implemented in stellar evolution codes and yield the rate at which the convective shell advances into the interior. Combining these velocities with the local equations for stellar structure, we find a minimum density for each gravitational potential below with the local equations for stellar structure, we find a minimum density for each gravitational potential below which the flame cannot propagate, and must die. Although detailed stellar models will have to be constructed to reslove some issues conclusively, our results that a CO white dwarf inginted at its edge will not burn carbon all the way to its center unless the mass of the white dwarf exceeds 0.8 solar mass. On the other hand, it is difficult to ignite carbon burning by compression alone anywhere in a white dwarf whose mass does not exceed 1.0 solar mass. Thus, compressionally ignited shell carbon burning in an accerting CO dwarf almost certainly propagates all the way to the center of the star. Implications for neutron star formation, and Type Ia supernova models, are briefly discussed. These are also applicable to massive stars in the about 10-12 solar mass range which ignite neon burning off center.

Sensitivity of tropospheric ozone to chemical kinetic uncertainties in air masses influenced by anthropogenic and biomass burning emissions

NASA Astrophysics Data System (ADS)

Ridley, D. A.; Cain, M.; Methven, J.; Arnold, S. R.

2017-07-01

We use a Lagrangian chemical transport model with a Monte Carlo approach to determine impacts of kinetic rate uncertainties on simulated concentrations of ozone, NOy and OH in a high-altitude biomass burning plume and a low-level industrial pollution plume undergoing long-range transport. Uncertainties in kinetic rate constants yield 10-12 ppbv (5th to 95th percentile) uncertainty in the ozone concentration, dominated by reactions that cycle NO and NO2, control NOx conversion to NOy reservoir species, and key reactions contributing to O3 loss (O(1D) + H2O, HO2 + O3). Our results imply that better understanding of the peroxyacetylnitrate (PAN) thermal decomposition constant is key to predicting large-scale O3 production from fire emissions and uncertainty in the reaction of NO + O3 at low temperatures is particularly important for both the anthropogenic and biomass burning plumes. The highlighted reactions serve as a useful template for targeting new laboratory experiments aimed at reducing uncertainties in our understanding of tropospheric O3 photochemistry.

Gender differences in burns: A study from emergency centres in the Western Cape, South Africa.

PubMed

Blom, Lisa; Klingberg, Anders; Laflamme, Lucie; Wallis, Lee; Hasselberg, Marie

2016-11-01

Little is known about gender differences in aetiology and management of acute burns in resource-constrained settings in South Africa. This cross-sectional study is based on burn case reports (n=1915) from eight emergency centres in Western Cape, South Africa (June 2012-May 2013). Male/female rate ratios by age group and age-specific incidence rates were compiled for urban and rural areas along with gender differences in proportions between children and adults for injury aetiology, burn severity, length of stay and patient disposition. Children 0-4 years in urban areas had the highest burn incidence but only among adults did male rates surpass females, with fire burns more common among men 20-39 years and hot liquid burns among men 55+ years. Men had a higher proportion of burns during weekends, from interpersonal violence and suspected use of alcohol/other substances, with more pronounced differences for hot liquid burns. Despite similar Abbreviated Injury Scale (AIS) scores, men were more often transferred to higher levels of care and women more often treated and discharged. Burns were far more common among children although gender differences arose only among adults. Men sustained more injuries of somewhat different aetiology and were referred to higher levels of care more often for comparable wound severity. The results suggest different disposition between men and women despite similar AIS scores. However, further studies with more comprehensive information on severity level and other care- and patient-related factors are needed to explore these results further. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Long-term mortality among older adults with burn injury: a population-based study in Australia

PubMed Central

Boyd, James H; Rea, Suzanne; Randall, Sean M; Wood, Fiona M

2015-01-01

Abstract Objective To assess if burn injury in older adults is associated with changes in long-term all-cause mortality and to estimate the increased risk of death attributable to burn injury. Methods We conducted a population-based matched longitudinal study – based on administrative data from Western Australia’s hospital morbidity data system and death register. A cohort of 6014 individuals who were aged at least 45 years when hospitalized for a first burn injury in 1980–2012 was identified. A non-injury comparison cohort, randomly selected from Western Australia’s electoral roll (n = 25 759), was matched to the patients. We used Kaplan–Meier plots and Cox proportional hazards regression to analyse the data and generated mortality rate ratios and attributable risk percentages. Findings For those hospitalized with burns, 180 (3%) died in hospital and 2498 (42%) died after discharge. Individuals with burn injury had a 1.4-fold greater mortality rate than those with no injury (95% confidence interval, CI: 1.3–1.5). In this cohort, the long-term mortality attributable to burn injury was 29%. Mortality risk was increased by both severe and minor burns, with adjusted mortality rate ratios of 1.3 (95% CI: 1.1–1.9) and 2.1 (95% CI: 1.9–2.3), respectively. Conclusion Burn injury is associated with increased long-term mortality. In our study population, sole reliance on data on in-hospital deaths would lead to an underestimate of the true mortality burden associated with burn injury. PMID:26240461

A Model-Based Approach to Infer Shifts in Regional Fire Regimes Over Time Using Sediment Charcoal Records

NASA Astrophysics Data System (ADS)

Itter, M.; Finley, A. O.; Hooten, M.; Higuera, P. E.; Marlon, J. R.; McLachlan, J. S.; Kelly, R.

2016-12-01

Sediment charcoal records are used in paleoecological analyses to identify individual local fire events and to estimate fire frequency and regional biomass burned at centennial to millenial time scales. Methods to identify local fire events based on sediment charcoal records have been well developed over the past 30 years, however, an integrated statistical framework for fire identification is still lacking. We build upon existing paleoecological methods to develop a hierarchical Bayesian point process model for local fire identification and estimation of fire return intervals. The model is unique in that it combines sediment charcoal records from multiple lakes across a region in a spatially-explicit fashion leading to estimation of a joint, regional fire return interval in addition to lake-specific local fire frequencies. Further, the model estimates a joint regional charcoal deposition rate free from the effects of local fires that can be used as a measure of regional biomass burned over time. Finally, the hierarchical Bayesian approach allows for tractable error propagation such that estimates of fire return intervals reflect the full range of uncertainty in sediment charcoal records. Specific sources of uncertainty addressed include sediment age models, the separation of local versus regional charcoal sources, and generation of a composite charcoal record The model is applied to sediment charcoal records from a dense network of lakes in the Yukon Flats region of Alaska. The multivariate joint modeling approach results in improved estimates of regional charcoal deposition with reduced uncertainty in the identification of individual fire events and local fire return intervals compared to individual lake approaches. Modeled individual-lake fire return intervals range from 100 to 500 years with a regional interval of roughly 200 years. Regional charcoal deposition to the network of lakes is correlated up to 50 kilometers. Finally, the joint regional charcoal deposition rate exhibits changes over time coincident with major climatic and vegetation shifts over the past 10,000 years. Ongoing work will use the regional charcoal deposition rate to estimate changes in biomass burned as a function of climate variability and regional vegetation pattern.

Effect of slow energy releasing on divergent detonation of Insensitive High Explosives

NASA Astrophysics Data System (ADS)

Hu, Xiaomian; Pan, Hao; Huang, Yong; Wu, Zihui

2014-03-01

There exists a slow energy releasing (SER) process in the slow reaction zone located behind the detonation wave due to the carbon cluster in the detonation products of Insensitive High Explosives (IHEs), and the process will affect the divergent detonation wave's propagation and the driving process of the explosives. To study the potential effect, a new artificial burn model including the SER process based on the programmed burn model is proposed in the paper. Quasi-steady analysis of the new model indicates that the nonlinearity of the detonation speed as a function of front curvature owes to the significant change of the reaction rate and the reaction zone length at the sonic state. What's more, in simulating the detonation of IHE JB-9014, the new model including the slow reaction can predict a slower jump-off velocity, in good agreement with the result of the test.

Biomass Burning Data and Information

Atmospheric Science Data Center

2015-04-21

Biomass Burning Data and Information This data set represents ... geographical and temporal distribution of total amount of biomass burned. These data may be used in general circulation models (GCMs) and ... models of the atmosphere. Project Title:  Biomass Burning Discipline:  Tropospheric Composition ...

Measurement of the photobleaching kinetics of semiconducting polymer films by the pump - probe method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozimova, A E; Bruevich, V V; Parashchuk, D Yu

2011-12-31

A phenomenological model of the laser photobleaching dynamics of a semiconducting polymer in a dual-beam scheme for different wavelengths of the burning and probe beams is developed. An experimental method is implemented based on this model, which allows one to investigate materials with significantly different photodegradation rates. The photodegradation quantum yield in mixtures of a semiconducting polymer belonging to polyparaphenylene vinylenes (MEH-PPV) with a low-molecular electron acceptor 2,4,7-trinitrofluorenone (TNF) is measured at burning wavelengths of 488 and 514 nm for different component ratios of MEHPPV : TNF. It is found that adding the acceptor decreases the polymer photodegradation quantum yieldmore » by at least four orders of magnitude in the MEH-PPV : TNF = 1 : 0.4 mixture; the photodegradation quantum yields are the same at both wavelengths. It is shown that the photodegradation rates of the MEH-PPV : TNF films measured by laser photobleaching and IR spectroscopy are in good agreement.« less

The trends of burns epidemiology in a tropical regional burns centre.

PubMed

Hwee, Jolie; Song, Christopher; Tan, Kok Chai; Tan, Bien Keem; Chong, Si Jack

2016-05-01

Singapore General Hospital (SGH) is a regional burns centre in Southeast Asia and is the only dedicated burns facility providing specialized burns care in Singapore. A cohort study was performed for burns patients admitted to SGH from 2011 to 2013. We compared our data with earlier studies and observed the trends of burns epidemiology in Singapore. Results were analyzed using the SPSS programme. 655 patients were admitted during this study period, a 35.9% increase from 2003 to 2005. Scalding by water and flame injury remain the top causes of burns and the mean extent of burn is 9.5%. TBSA correlates with the incidence of burn infection, bacteremia and mortality. Patients with ≥20% TBSA are at a higher risk of bacteremia, and ≥ 34% TBSA is a predictor of mortality. 4.9% (n=32) of our patients developed bacteremia. Bacteremia was associated with a surgical duration of ≥80min. Patients with bacteremia incurred longer hospitalization, and had higher mortality rates. Overall mortality rate of our burns patients has decreased from 4.5% to 2.7% (n=18). Key factors of mortality include inhalational injury, bacteremia and ≥20% TBSA. This is a large epidemiology study of a tropical region burns centre. A total of 655 burns cases over a 3-year period were analyzed. We analysed the key factors associated with adverse outcomes including burns infection, bacteremia and mortality, factors associated with mortality, and discussed strategies on the optimization of burns care. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Multimode VCSEL model for wide frequency-range RIN simulation

NASA Astrophysics Data System (ADS)

Perchoux, Julien; Rissons, Angélique; Mollier, Jean-Claude

2008-01-01

In this paper, we present an equivalent circuit model for oxide-confined AlGaAs/GaAs VCSEL with the noise contribution adapted to optomicrowave links applications. This model is derived from the multimode rate equations. In order to understand the modal competition process, we restrain our description to a two-modes rate equations system affected by the spectral hole-burning. The relative intensity noise (RIN) measurements which were achieved on a prober in Faraday cage confirm the low frequency enhancement described by the model. We validate our model for a wide frequency-range [1 MHz-10 GHz] and high bias level up to six times the threshold current.

The effect of a changed environment on bacterial colonization rates in an established burns centre

PubMed Central

Wormald, P. J.

1970-01-01

In an established burns centre which moved from an old building to new purpose-designed premises, colonization rates of patients' burns with Staphylococcus aureus, Pseudomonas aeruginosa and other Gram-negative bacilli were not reduced. Colonization rates with Streptococcus pyogenes increased but the increase was mainly due to multiple importations in the new premises of a strain of higher communicability than any seen in the old. In the first 32 months in the new environment 10 patients were found colonized with pseudomonas on admission and 20 became colonized in the unit. A much higher proportion of patients with burns of more than 30% body surface became colonized than of patients with less. About one-third of the above 20 patients became colonized with strains already isolated from another patient; all but one of them had small area burns. Cross-infection was not observed from numerous heavily colonized patients with high percentage burns. This paradox is discussed in detail. Basin outflows in the new premises became colonized with P. aeruginosa of two serotypes not found on patients in this unit. PMID:4993291

The effect of a changed environment on bacterial colonization rates in an established burns centre.

PubMed

Wormald, P J

1970-12-01

In an established burns centre which moved from an old building to new purpose-designed premises, colonization rates of patients' burns with Staphylococcus aureus, Pseudomonas aeruginosa and other Gram-negative bacilli were not reduced. Colonization rates with Streptococcus pyogenes increased but the increase was mainly due to multiple importations in the new premises of a strain of higher communicability than any seen in the old.In the first 32 months in the new environment 10 patients were found colonized with pseudomonas on admission and 20 became colonized in the unit. A much higher proportion of patients with burns of more than 30% body surface became colonized than of patients with less. About one-third of the above 20 patients became colonized with strains already isolated from another patient; all but one of them had small area burns. Cross-infection was not observed from numerous heavily colonized patients with high percentage burns. This paradox is discussed in detail. Basin outflows in the new premises became colonized with P. aeruginosa of two serotypes not found on patients in this unit.

Contributions of Kansas rangeland burning to ambient O3: Analysis of data from 2001 to 2016.

PubMed

Liu, Zifei; Liu, Yang; Murphy, James P; Maghirang, Ronaldo

2018-03-15

Prescribed range/pasture burning is a common practice in Kansas to enhance the nutritional value of native grasses and control invading weeds, trees, and brush. A major concern associated with the burning is the contribution of smoke to elevated ground level ambient ozone (O 3 ). The objective of this study is to estimate contributions of Kansas rangeland burning to ambient O 3 mixing ratios through regression analysis (1) between observed O 3 data and available satellite burn activity data from 2001 to 2016; and (2) between observed O 3 data and the smoke contributions to PM 2.5 which were resolved from receptor modeling. Positive correlations were observed between ambient O 3 levels and the acres burned each year estimated from satellite imagery. When burned acres in April were larger than or equal to 1.9 million, O 3 >70ppb occurred at least at one of the ten monitoring sites in Kansas. Statistical regression models of daily maximum 8-hour O 3 mixing ratios were developed at each of the ten monitoring sites using meteorological predictors. The O 3 model residuals that were not explained by the meteorological effect models were affected by PM 2.5 contributors including sulfate/industrial sources and emissions that generated secondary organic particles, such as rangeland burning, which were derived from receptor modeling. The average O 3 model residual on the high O 3 days in April was 21±9ppb, which was likely associated with smoke emissions from burning. Research will continue to obtain daily satellite burn activity data and to correlate burn data with daily O 3 data, so that modeling of O 3 levels can be improved under influences of daily burn activities. Less frequency of high O 3 days was observed in April since 2011, which may be partly due to implementation of the Flint Hills Smoke Management Plan which promoted better timing of burns. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of soil infiltration rates in burned and unburned mountainous watersheds

USGS Publications Warehouse

Martin, D.A.; Moody, J.A.

2001-01-01

Steady-state infiltration measurements were made at mountainous sites in New Mexico and Colorado, USA, with volcanic and granitic soils after wildfires and at comparable unburned sites. We measured infiltration in the New Mexico volcanic soils under two vegetation types, ponderosa pine and mixed conifer, and in the Colorado granitic soils under ponderosa pine vegetation. These measurements were made within high-severity burn areas using a portable infiltrometer with a 0.017 m2 infiltration area and artificial rainfall rates ranging from 97 to 440 mm h-1. Steady-state infiltration rates were less at all burned sites relative to unburned sites. The volcanic soil with ponderosa pine vegetation showed the greatest difference in infiltration rates with a ratio of steady-state infiltration rate in burned sites to unburned soils equal to 0.15. Volcanic soils with mixed conifer vegetation had a ratio (burned to unburned soils) of at most 0.38, and granitic soils with ponderosa pine vegetation had a ratio of 0.38. Steady-state infiltration rates on unburned volcanic and granitic soils with ponderosa pine vegetation are not statistically different. We present data on the particle-size distribution at all the study sites and examples of wetting patterns produced during the infiltration experiments. Published in 2001 by John Wiley and Sons, Ltd.

Thermal decomposition of high-nitrogen energetic compounds: TAGzT and GUzT

NASA Astrophysics Data System (ADS)

Hayden, Heather F.

The U.S. Navy is exploring high-nitrogen compounds as burning-rate additives to meet the growing demands of future high-performance gun systems. Two high-nitrogen compounds investigated as potential burning-rate additives are bis(triaminoguanidinium) 5,5-azobitetrazolate (TAGzT) and bis(guanidinium) 5,5'-azobitetrazolate (GUzT). Small-scale tests showed that formulations containing TAGzT exhibit significant increases in the burning rates of RDX-based gun propellants. However, when GUzT, a similarly structured molecule was incorporated into the formulation, there was essentially no effect on the burning rate of the propellant. Through the use of simultaneous thermogravimetric modulated beam mass spectrometry (STMBMS) and Fourier-Transform ion cyclotron resonance (FTICR) mass spectrometry methods, an investigation of the underlying chemical and physical processes that control the thermal decomposition behavior of TAGzT and GUzT alone and in the presence of RDX, was conducted. The objective was to determine why GUzT is not as good a burning-rate enhancer in RDX-based gun propellants as compared to TAGzT. The results show that TAGzT is an effective burning-rate modifier in the presence of RDX because the decomposition of TAGzT alters the initial stages of the decomposition of RDX. Hydrazine, formed in the decomposition of TAGzT, reacts faster with RDX than RDX can decompose itself. The reactions occur at temperatures below the melting point of RDX and thus the TAGzT decomposition products react with RDX in the gas phase. Although there is no hydrazine formed in the decomposition of GUzT, amines formed in the decomposition of GUzT react with aldehydes, formed in the decomposition of RDX, resulting in an increased reaction rate of RDX in the presence of GUzT. However, GUzT is not an effective burning-rate modifier because its decomposition does not alter the initial gas-phase decomposition of RDX. The decomposition of GUzT occurs at temperatures above the melting point of RDX. Therefore, the decomposition of GUzT affects reactions that are dominant in the liquid phase of RDX. Although GUzT is not an effective burning-rate modifier, features of its decomposition where the reaction between amines formed in the decomposition of GUzT react with the aldehydes, formed in the decomposition of RDX, may have implications from an insensitive-munitions perspective.

Clinical study of cultured epithelial autografts in liquid suspension in severe burn patients.

PubMed

Yim, Haejun; Yang, Hyeong Tae; Cho, Yong Suk; Seo, Cheong Hoon; Lee, Boung Chul; Ko, Jang Hyu; Kwak, In Suk; Kim, Dohern; Hur, Jun; Kim, Jong Hyun; Chun, Wook

2011-09-01

We address the clinical application of the suspension type cultured epithelial autografts (CEAs), Keraheal™ (MCTT, Seoul, Korea), along with the effects, application method, merits and demerits thereof. From February 2007 to June 2010, 29 burn patients with extensive burns, participated in the suspension type of CEA clinical test. A widely meshed autograft (1:4-6 ratio) was applied to the wound bed and the suspension type CEA was sprayed with a Tissomat cell sprayer, followed by a Tissucol spray, a fibrin sealant. The patients' (men/women=26/3) median (interquartile ranges) age was 42 (30-49) years old, the burned TBSA was 55 (44-60) %, and the full thickness burn area was 40 (30-46.5) %. The area of Keraheal™ applied was 800 (400-1200) cm(2). The take rate was 96 (90.5-99) % and 100 (98.5-100) % at 2 and 4 weeks after treatment with Keraheal™, respectively. The Vancouver burn scar scale was 5 (4-6.5), 4 (3-6), and 3 (2-4) at 8, 12 and 24 weeks after the Keraheal™ application. Widely meshed autograft must be applied in massive burns but it's take rate is greatly reduced. The CEAs enhance the take rate of a wide meshed autograft in massive burns and allow for grafting wide meshed autograft together with acellular dermal matrix in some cases. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

Effects of fire on golden eagle territory occupancy and reproductive success

USGS Publications Warehouse

Kochert, Michael N.; Steenhof, Karen; Marzluff, J.M.; Carpenter, L.B.

1999-01-01

We examined effects of fire on golden eagle (Aquila chrysaetos) territory occupancy and reproductive success in southwestern Idaho because wildfires since 1980 have resulted in large-scale losses of shrub habitat in the Snake River Plain. Success (percentage of pairs that raised young) at burned territories declined after major fires (P = 0.004). Pairs in burned areas that could expand into adjacent vacant territories were as successful as pairs in unburned territories and more successful than pairs in burned territories that could not expand. Success at extensively burned territories was lowest 4-6 years after burning but increased 4-5 years later. The incidence and extent of fires did not help predict territories that would have low occupancy and success rates in postburn years. The presence of a vacant neighboring territory and the amount of agriculture and proportion of shrubs within 3 km of the nesting centroid best predicted probability of territory occupancy. Nesting success during preburn years best predicted the probability of a territory being successful in postburn years. Burned territories with high success rates during preburn years continued to have high success rates during postburn years, and those with low success in preburn years continued to be less successful after burning. In areas where much shrub habitat has been lost to fire, management for golden eagles should include active fire suppression and rehabilitation of burned areas.

Allocating resources to large wildland fires: a model with stochastic production rates

Treesearch

Romain Mees; David Strauss

1992-01-01

Wildland fires that grow out of the initial attack phase are responsible for most of the damage and burned area. We model the allocation of fire suppression resources (ground crews, engines, bulldozers, and airdrops) to these large fires. The fireline at a given future time is partitioned into homogeneous segments on the basis of fuel type, available resources, risk,...

[Analysis of the pathogenic characteristics of 162 severely burned patients with bloodstream infection].

PubMed

Gong, Y L; Yang, Z C; Yin, S P; Liu, M X; Zhang, C; Luo, X Q; Peng, Y Z

2016-09-20

To analyze the distribution and drug resistance of pathogen isolated from severely burned patients with bloodstream infection, so as to provide reference for the clinical treatment of these patients. Blood samples of 162 severely burned patients (including 120 patients with extremely severe burn) with bloodstream infection admitted into our burn ICU from January 2011 to December 2014 were collected. Pathogens were cultured by fully automatic blood culture system, and API bacteria identification panels were used to identify pathogen. Kirby-Bauer paper disk diffusion method was used to detect the drug resistance of major Gram-negative and -positive bacteria to 37 antibiotics including ampicillin, piperacillin and teicoplanin, etc. (resistance to vancomycin was detected by E test), and drug resistance of fungi to 5 antibiotics including voriconazole and amphotericin B, etc. Modified Hodge test was used to further identify imipenem and meropenem resistant Klebsiella pneumonia. D test was used to detect erythromycin-induced clindamycin resistant Staphylococcus aureus. The pathogen distribution and drug resistance rate were analyzed by WHONET 5.5. Mortality rate and infected pathogens of patients with extremely severe burn and patients with non-extremely severe burn were recorded. Data were processed with Wilcoxon rank sum test. (1) Totally 1 658 blood samples were collected during the four years, and 339 (20.4%) strains of pathogens were isolated. The isolation rate of Gram-negative bacteria, Gram-positive bacteria, and fungi were 68.4% (232/339), 24.5% (83/339), and 7.1% (24/339), respectively. The top three pathogens with isolation rate from high to low were Acinetobacter baumannii, Staphylococcus aureus, and Pseudomonas aeruginosa in turn. (2) Except for the low drug resistance rate to polymyxin B and minocycline, drug resistance rate of Acinetobacter baumannii to the other antibiotics were relatively high (81.0%-100.0%). Pseudomonas aeruginosa was sensitive to polymyxin B but highly resistant to other antibiotics (57.7%-100.0%). Enterobacter cloacae was sensitive to imipenem and meropenem, while its drug resistance rates to ciprofloxacin, levofloxacin, cefoperazone/sulbactam, cefepime, piperacillin/tazobactam were 25.0%-49.0%, and those to the other antibiotics were 66.7%-100.0%. Drug resistance rates of Klebsiella pneumoniae to cefoperazone/sulbactam, imipenem, and meropenem were low (5.9%-15.6%, two imipenem- and meropenem-resistant strains were identified by modified Hodge test), while its drug resistance rates to amoxicillin/clavulanic acid, piperacillin/tazobactam, cefepime, cefoxitin, amikacin, levofloxacin were 35.3%-47.1%, and those to the other antibiotics were 50.0%-100.0%. (3) Drug resistance rates of methicillin-resistant Staphylococcus aureus (MRSA) to most of the antibiotics were higher than those of the methicillin-sensitive Staphylococcus aureus (MSSA). MRSA was sensitive to linezolid, vancomycin, and teicoplanin, while its drug resistance rates to compound sulfamethoxazole, clindamycin, minocycline, and erythromycin were 5.3%-31.6%, and those to the other antibiotics were 81.6%-100.0%. Except for totally resistant to penicillin G and tetracycline, MSSA was sensitive to the other antibiotics. Fourteen Staphylococcus aureus strains were resistant to erythromycin-induced clindamycin. Enterococcus was sensitive to vancomycin and teicoplanin, while its drug resistance rates to linezolid, chloramphenicol, nitrofurantoin, and high unit gentamicin were low (10.0%-30.0%), and those to ciprofloxacin, erythromycin, minocycline, and ampicillin were high (60.0%-80.0%). Enterococcus was fully resistant to rifampicin. (4) Fungi was sensitive to amphotericin B, and drug resistance rates of fungi to voriconazole, fluconazole, itraconazole, and ketoconazole were 7.2%-12.5%. (5) The mortality of patients with extremely severe burn was higher than that of patients with non-extremely severe burn. The variety of infected pathogens in patients with extremely severe burn significantly outnumbered that in patients with non-extremely severe burn (Z=-2.985, P=0.005). The variety of pathogen in severely burned patients with bloodstream infection is wide, with the main pathogens as Acinetobacter baumannii, Staphylococcus aureus, and Pseudomonas aeruginosa, and the drug resistance situation is grim. The types of infected pathogen in patients with extremely severe burn are more complex, and the mortality of these patients is higher when compared with that of patients with non-extremely severe burn.

Flammability testing conducted in support of Apollo 13

NASA Technical Reports Server (NTRS)

Leger, L. J.; Bricker, R. W.

1971-01-01

In support of the Apollo 13 investigation of the oxygen tank failure, flame propagation rates were determined for Teflon insulation in cryogenic and ambient temperature oxygen for upward, downward, and zero g burns. The propagation rates depended heavily on configuration and varied from 4.8 to 10.9 cm/sec for upward one g burns to 0.48 cm/sec for zero g burns. In addition to the flame propagation rates, tests were conducted to determine if Teflon burning in cryogenic oxygen could ignite metals (promoted ignition) with which it came in contact. Tests conducted on various metal alloys used in the oxygen tank indicated that most of the alloys could be ignited by burning Teflon in certain configurations. After the propagation rates and promoted metal ignitions had been evaluated, a test was conducted on a quantity gauge and wire harness used in the oxygen tank to determine if flame propagation to the tank wall was possible. Propagation of the wire bundle after ignition resulted in a catastrophic failure of the test vessel in the area of the quantity gauge.

Fire spread in chaparral – a comparison of laboratory data and model predictions in burning live fuels

Treesearch

David R. Weise; Eunmo Koo; Xiangyang Zhou; Shankar Mahalingam; Frédéric Morandini; Jacques-Henri Balbi

2016-01-01

Fire behaviour data from 240 laboratory fires in high-density live chaparral fuel beds were compared with model predictions. Logistic regression was used to develop a model to predict fire spread success in the fuel beds and linear regression was used to predict rate of spread. Predictions from the Rothermel equation and three proposed changes as well as two physically...

The effect of density and thermal diffusivity of wood on the rate of burning of wood cribs

Treesearch

H.D. Bruce; W.Y. Pong; W.L. Fons

1961-01-01

A program of research on free-burning wood fires is being conducted by the Forest Service to build up experimental data on the properties of such fires, with the iltimate objective of describing the physical phenomena in terms of fundamental laws. Density was the first wood property investigated. This report gives data on the rate of burning of cribs of five species...

40 CFR 63.1564 - What are my requirements for metal HAP emissions from catalytic cracking units?

Code of Federal Regulations, 2013 CFR

2013-07-01

... coke burn-off emission limit (Option 4). (2) Comply with each operating limit in Table 2 of this... the PM emission rate (lb/1,000 lbs of coke burn-off) for each run using Equations 1, 2, and 3 (if applicable) of this section as follows: ER11AP02.000 Where: Rc = Coke burn-off rate, kg/hr (lb/hr); Qr...

40 CFR 63.1564 - What are my requirements for metal HAP emissions from catalytic cracking units?

Code of Federal Regulations, 2014 CFR

2014-07-01

... coke burn-off emission limit (Option 4). (2) Comply with each operating limit in Table 2 of this... the PM emission rate (lb/1,000 lbs of coke burn-off) for each run using Equations 1, 2, and 3 (if applicable) of this section as follows: ER11AP02.000 Where: Rc = Coke burn-off rate, kg/hr (lb/hr); Qr...

40 CFR 63.1564 - What are my requirements for metal HAP emissions from catalytic cracking units?

Code of Federal Regulations, 2012 CFR

2012-07-01

... coke burn-off emission limit (Option 4). (2) Comply with each operating limit in Table 2 of this... the PM emission rate (lb/1,000 lbs of coke burn-off) for each run using Equations 1, 2, and 3 (if applicable) of this section as follows: ER11AP02.000 Where: Rc = Coke burn-off rate, kg/hr (lb/hr); Qr...

Campaign datasets for Biomass Burning Observation Project (BBOP)

DOE Data Explorer

Kleinman,Larry; Mei,Fan; Arnott,William; Buseck,Peter; Chand,Duli; Comstock,Jennifer; Dubey,Manvendra; Lawson,Paul; Long,Chuck; Onasch,Timothy; Sedlacek,Arthur; Senum,Gunnar; Shilling,John; Springston,Stephen; Tomlinson,Jason; Wang,Jian

2014-04-24

This field campaign will address multiple uncertainties in aerosol intensive properties, which are poorly represented in climate models, by means of aircraft measurements in biomass burning plumes. Key topics to be investigated are: 1. Aerosol mixing state and morphology 2. Mass absorption coefficients (MACs) 3. Chemical composition of non-refractory material associated with light-absorbing carbon (LAC) 4. Production rate of secondary organic aerosol (SOA) 5. Microphysical processes relevant to determining aerosol size distributions and single scattering albedo (SSA) 6. CCN activity. These topics will be investigated through measurements near active fires (0-5 hours downwind), where limited observations indicate rapid changes in aerosol properties, and in biomass burning plumes aged >5 hours. Aerosol properties and their time evolution will be determined as a function of fire type, defined according to fuel and the mix of flaming and smoldering combustion at the source.

Aged boreal biomass-burning aerosol size distributions from BORTAS 2011

NASA Astrophysics Data System (ADS)

Sakamoto, K. M.; Allan, J. D.; Coe, H.; Taylor, J. W.; Duck, T. J.; Pierce, J. R.

2015-02-01

Biomass-burning aerosols contribute to aerosol radiative forcing on the climate system. The magnitude of this effect is partially determined by aerosol size distributions, which are functions of source fire characteristics (e.g. fuel type, MCE) and in-plume microphysical processing. The uncertainties in biomass-burning emission number-size distributions in climate model inventories lead to uncertainties in the CCN (cloud condensation nuclei) concentrations and forcing estimates derived from these models. The BORTAS-B (Quantifying the impact of BOReal forest fires on Tropospheric oxidants over the Atlantic using Aircraft and Satellite) measurement campaign was designed to sample boreal biomass-burning outflow over eastern Canada in the summer of 2011. Using these BORTAS-B data, we implement plume criteria to isolate the characteristic size distribution of aged biomass-burning emissions (aged ~ 1-2 days) from boreal wildfires in northwestern Ontario. The composite median size distribution yields a single dominant accumulation mode with Dpm = 230 nm (number-median diameter) and σ = 1.5, which are comparable to literature values of other aged plumes of a similar type. The organic aerosol enhancement ratios (ΔOA / ΔCO) along the path of Flight b622 show values of 0.09-0.17 μg m-3 ppbv-1 (parts per billion by volume) with no significant trend with distance from the source. This lack of enhancement ratio increase/decrease with distance suggests no detectable net OA (organic aerosol) production/evaporation within the aged plume over the sampling period (plume age: 1-2 days), though it does not preclude OA production/loss at earlier stages. A Lagrangian microphysical model was used to determine an estimate of the freshly emitted size distribution corresponding to the BORTAS-B aged size distributions. The model was restricted to coagulation and dilution processes based on the insignificant net OA production/evaporation derived from the ΔOA / ΔCO enhancement ratios. We estimate that the young-plume median diameter was in the range of 59-94 nm with modal widths in the range of 1.7-2.8 (the ranges are due to uncertainty in the entrainment rate). Thus, the size of the freshly emitted particles is relatively unconstrained due to the uncertainties in the plume dilution rates.

Scheduling prescribed burns for hazard reduction in the southeast

Treesearch

Stephen S. Sackett

1975-01-01

Twelve-year studies in the southeastern Coastal Plain revealed that pine stands should be burned every three years to reduce natural fuels and thus forestall damage from possible wildfires. Rates of overstory growth were not significantly different in burned and unburned stands. Guidelines for prescribed burning of pine stands in this region are presented.

Tundra fire disturbance homogonizes belowground food web structure, function and dynamics

NASA Astrophysics Data System (ADS)

Moore, J. C.; Pressler, Y.; Koltz, A.; Asmus, A.; Simpson, R.

2016-12-01

Tundra fires on Alaska's North Slope are on the rise due to increased lightning strikes since 2000. On July 16, 2007 lightning ignited the Anaktuvuk River fire, burning a 40-by-10 mile swath of tundra about 24 miles north of Toolik Field Station. The fire burned 401 square miles, was visible from space, and released more than 2.3 million tons of carbon into the atmosphere. A large amount of the organic layer of the soil was burned, changing the over all composition of the site and exposing deeper soil horizons. Due to fundamental transitions in soil characteristics and vegetation we hypothesized that the belowground food web community would be affected both in terms of biomass and location within the soil profile. Microbial biomass was reduced with burn severity. In the lower organic horizon there was a significant reduction in fungal biomass but we did not observe this effect in the upper organic soil. We did not observe a significant effect of burn severity on individual group biomass within higher trophic levels. Canonical Discriminant Analysis using the biomass estimates of the functional groups in the food webs found that the webs are becoming increasingly homogenized in the severely burned site compared to the moderately burned and unburned sites. The unburned soils differed significantly from soil at both burn sites; the greatest effects on food web structure were at the lower organic depth, whereas. We modeled the effects of the fire on soil organic matter processing rates and energy flow through the three food webs. The model estimated a decrease in C and N mineralization with fire severity, due in large part to the loss of organic material. While the organic horizon at the unburned site had 12 times greater C and N mineralization than the mineral soils, we observed little to no difference in C and N mineralization between the organic and mineral soil horizons in the moderately and severely burned sites. Our results show that the fire significantly altered the trophic structure of the soil food web, with loss of trophic complexity with increasing fire severity, which correlated strongly with C and N processing and food web stability.

Investigation of critical burning of fuel droplets

NASA Technical Reports Server (NTRS)

Allison, C. B.; Canada, G. S.

1972-01-01

Fuel droplets were simulated by porous spheres having diameters in the range 0.63 to 1.9 cm and combustion tests were conducted at pressures up to 78 atm in a quiescent cold air environment. Measurements were made of the burning rate and liquid surface temperature during steady combustion. A high pressure flat flame burner apparatus is under development in order to allow testing of high pressure droplet burning in a combustion gas environment. Work was continued on the high pressure strand combustion characteristics of liquid fuels, with the major emphasis on hydrazine. Data was obtained on the burning rate and liquid surface temperatures at pressures in the range 7 to 500 psia. The response of a burning liquid monopropellant to imposed pressure oscillations is being investigated.

Space shuttle propulsion estimation development verification

NASA Technical Reports Server (NTRS)

Rogers, Robert M.

1989-01-01

The application of extended Kalman filtering to estimating the Space Shuttle Propulsion performance, i.e., specific impulse, from flight data in a post-flight processing computer program is detailed. The flight data used include inertial platform acceleration, SRB head pressure, SSME chamber pressure and flow rates, and ground based radar tracking data. The key feature in this application is the model used for the SRB's, which is a nominal or reference quasi-static internal ballistics model normalized to the propellant burn depth. Dynamic states of mass overboard and propellant burn depth are included in the filter model to account for real-time deviations from the reference model used. Aerodynamic, plume, wind and main engine uncertainties are also included for an integrated system model. Assuming uncertainty within the propulsion system model and attempts to estimate its deviations represent a new application of parameter estimation for rocket powered vehicles. Illustrations from the results of applying this estimation approach to several missions show good quality propulsion estimates.

Burn Wound Healing and Treatment: Review and Advancements

DTIC Science & Technology

2015-06-12

different days post burn. Burns. 2009;35:36–45. 176. Ogden CL, Carroll MD, Kit BK, Flegal KM. Prevalence of childhood and adult obesity in the United...invasive imaging modalities into the routine treatment of burn wounds. Obese patients As the obese population continues to grow [176], new treatment...approaches will be required. Obese burn pa- tients present with a variety of unique characteristics that include: increased rates of diabetes

Self-organized criticality in type I X-ray bursts

NASA Astrophysics Data System (ADS)

Wang, J. S.; Wang, F. Y.; Dai, Z. G.

2017-11-01

Type I X-ray bursts in a low-mass X-ray binary are caused by unstable nuclear burning of accreted materials. Semi-analytical and numerical studies of unstable nuclear burning have successfully reproduced the partial properties of this kind of burst. However, some other properties (e.g. the waiting time) are not well explained. In this paper, we find that the probability distributions of fluence, peak count, rise time, duration and waiting time can be described as power-law-like distributions. This indicates that type I X-ray bursts may be governed by a self-organized criticality (SOC) process. The power-law index of the waiting time distribution (WTD) is around -1, which is not predicted by any current waiting time model. We propose a physical burst rate model, in which the mean occurrence rate is inversely proportional to time: λ ∝ t-1. In this case, the WTD is explained well by a non-stationary Poisson process within the SOC theory. In this theory, the burst size is also predicted to follow a power-law distribution, which requires that the emission area covers only part of the neutron star surface. Furthermore, we find that the WTDs of some astrophysical phenomena can also be described by similar occurrence rate models.

Dementia: A risk factor for burns in the elderly.

PubMed

Harvey, Lara; Mitchell, Rebecca; Brodaty, Henry; Draper, Brian; Close, Jacqueline

2016-03-01

Older people are disproportionately at risk of burn and have a high risk of dementia; however the impact of dementia on risk of burn is unknown. Linked hospitalisation and death records for individuals aged 65 years and older admitted to a NSW hospital for a burn over the ten year period 2003-2012 were analysed. Demographic and burn characteristics and health outcomes were compared for people with and without dementia. Incidence rates were calculated per 100,000 population and negative binomial regression was used to examine temporal trends. Of the 1535 older people hospitalised for a burn, 11.0% had a record of dementia. The age-standardised incidence rate for people with dementia was 22.7 per 100,000, and for people without dementia was 14.2 per 100,000 population, an incident rate ratio (IRR) of 1.6 (95%CI 1.3-2.0, p<0.0001). There was no significant change in rates over time. People with dementia were more likely to be admitted with burns to the trunk and have greater than 20% total body surface area (TBSA) burn. Mean length of stay (LOS) was more than double (24 vs 12 days) and 30-day mortality three times higher (15.4% vs 5.1%) for people with dementia. Adjusting for differences in age, sex, TBSA, inhalation injury, comorbidities and complications eliminated the increased mortality but not the difference in LOS. People with dementia were more likely to have been burnt by hot tap water (RR 2.3; 95%CI 1.8-2.8, p<0.0001) and ignition of clothing/nightwear (RR 2.6; 95% CI 1.2-5.4, p=0.0149) and to have sustained the burn in residential aged care (20.0%). Burns in people with dementia are significant injuries, which have not decreased over the past ten years despite prevention efforts to reduce burns in older people. Targeted prevention education in the home and residential aged care facilities is warranted. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Epidemiology of Burns in Rural Bangladesh: An Update.

PubMed

He, Siran; Alonge, Olakunle; Agrawal, Priyanka; Sharmin, Shumona; Islam, Irteja; Mashreky, Saidur Rahman; Arifeen, Shams El

2017-04-05

Each year, approximately 265,000 deaths occur due to burns on a global scale. In Bangladesh, around 173,000 children under 18 sustain a burn injury. Since most epidemiological studies on burn injuries in low and middle-income countries are based on small-scale surveys or hospital records, this study aims to derive burn mortality and morbidity measures and risk factors at a population level in Bangladesh. A household survey was conducted in seven rural sub-districts of Bangladesh in 2013 to assess injury outcomes. Burn injuries were one of the external causes of injury. Epidemiological characteristics and risk factors were described using descriptive as well as univariate and multivariate logistic regression analyses. The overall mortality and morbidity rates were 2 deaths and 528 injuries per 100,000 populations. Females had a higher burn rate. More than 50% of injuries were seen in adults 25 to 64 years of age. Most injuries occurred in the kitchen while preparing food. 88% of all burns occurred due to flame. Children 1 to 4 years of age were four times more likely to sustain burn injuries as compared to infants. Age-targeted interventions, awareness of first aid protocols, and improvement of acute care management would be potential leads to curb death and disability due to burn injuries.

Suicide by burning: epidemiological and clinical profiles.

PubMed

Theodorou, Panagiotis; Phan, Vu T Q; Weinand, Christian; Maegele, Marc; Maurer, Christoph A; Perbix, Walter; Leitsch, Sebastian; Lefering, Rolf; Spilker, Gerald

2011-04-01

Self-immolation constitutes a rare form of suicide in developed countries, though it accounts for unique injury characteristics in the burn intensive care unit. The aim of this study was to present the epidemiological and clinical features of patients burned during a suicidal attempt seen in a North Rhine-Westphalia burn intensive care unit (BICU). To address this aim, we undertook a 21-year retrospective study involving patients with thermal injuries admitted to the largest burn unit in Germany. A total of 125 suicide-related burn victims were identified in the study period (9.4%). Comparing the self-immolation group with the rest burn patient cohort, suicide victims were more likely to be single and to act under the influence of alcohol. The suicidal group had a larger extent of burns, higher incidence of inhalation injury, required more surgical procedures, catecholamines, blood transfusions, and a longer BICU stay. Their clinical course was complicated by prolonged intubation period, higher rate of multiple drug-resistant bacteria acquisition and sepsis, leading to a higher mortality rate. Although the proportion of self-immolation victims among all burned patients is not high, the markedly higher severity of their burns and their poorer quality of outcomes makes them an important clinical subgroup for further study.

Epidemiology of Burns in Rural Bangladesh: An Update

PubMed Central

He, Siran; Alonge, Olakunle; Agrawal, Priyanka; Sharmin, Shumona; Islam, Irteja; Mashreky, Saidur Rahman; Arifeen, Shams El

2017-01-01

Each year, approximately 265,000 deaths occur due to burns on a global scale. In Bangladesh, around 173,000 children under 18 sustain a burn injury. Since most epidemiological studies on burn injuries in low and middle-income countries are based on small-scale surveys or hospital records, this study aims to derive burn mortality and morbidity measures and risk factors at a population level in Bangladesh. A household survey was conducted in seven rural sub-districts of Bangladesh in 2013 to assess injury outcomes. Burn injuries were one of the external causes of injury. Epidemiological characteristics and risk factors were described using descriptive as well as univariate and multivariate logistic regression analyses. The overall mortality and morbidity rates were 2 deaths and 528 injuries per 100,000 populations. Females had a higher burn rate. More than 50% of injuries were seen in adults 25 to 64 years of age. Most injuries occurred in the kitchen while preparing food. 88% of all burns occurred due to flame. Children 1 to 4 years of age were four times more likely to sustain burn injuries as compared to infants. Age-targeted interventions, awareness of first aid protocols, and improvement of acute care management would be potential leads to curb death and disability due to burn injuries. PMID:28379160

An educational board game for learning and teaching burn care: A preliminary evaluation.

PubMed

Whittam, Alexander M; Chow, Whitney

2017-01-01

Timely and effective assessment, resuscitation and transfer of patients with severe burns has been demonstrated to improve outcome. A dedicated one-day course exists to equip all frontline emergency healthcare workers with the necessary knowledge and skills to manage severe burn injuries. More recently, a board game has been developed which aims to act as a learning and practice development tool for those managing burn injuries. We present the findings of our preliminary evaluation of this game. We played this game with a multidisciplinary group of staff including doctors, nurses and therapists. A proportion of these participants had previously completed the Emergency Management of Severe Burns (EMSB) course. We obtained subjective results from a questionnaire, using both Likert-type ratings and open-ended questions. The styling of the game and ease of instructions was rated from 'average' to 'excellent'. The relevance of questions was rated from 'good' to 'excellent'. The usefulness of the game to increase knowledge and stimulate discussion was rated between 'good' and 'excellent'. All participants stated that they would recommend the game to other healthcare professionals. This is the only burns and plastic surgery-related educational game in the literature. Educational games adhere to principles of adult learning but there is insufficient evidence in the literature to either confirm or refute their utility. Our preliminary evaluation of this game has shown that it achieves its main aims, namely to increase knowledge in burn care and to stimulate discussion. Further work is required to assess the board game.

Influence of slope on fire spread rate

Treesearch

B.W. Butler; W.R. Anderson; E.A. Catchpole

2007-01-01

Data demonstrate the effect of slope on heading and backing fires burning through woody fuels. The data indicate that the upper limit of heading fire rate of spread is defined by the rate of spread up a vertical fuel array, and the lower limit is defined by the rate of spread of a backing fire burning downslope. The minimum spread rate is found to occur at nominally --...

Pulsating Hydrodynamic Instability in a Dynamic Model of Liquid-Propellant Combustion

NASA Technical Reports Server (NTRS)

Margolis, Stephen B.; Sacksteder, Kurt (Technical Monitor)

1999-01-01

Hydrodynamic (Landau) instability in combustion is typically associated with the onset of wrinkling of a flame surface, corresponding to the formation of steady cellular structures as the stability threshold is crossed. In the context of liquid-propellant combustion, such instability has recently been shown to occur for critical values of the pressure sensitivity of the burning rate and the disturbance wavenumber, significantly generalizing previous classical results for this problem that assumed a constant normal burning rate. Additionally, however, a pulsating form of hydrodynamic instability has been shown to occur as well, corresponding to the onset of temporal oscillations in the location of the liquid/gas interface. In the present work, we consider the realistic influence of a nonzero temperature sensitivity in the local burning rate on both types of stability thresholds. It is found that for sufficiently small values of this parameter, there exists a stable range of pressure sensitivities for steady, planar burning such that the classical cellular form of hydrodynamic instability and the more recent pulsating form of hydrodynamic instability can each occur as the corresponding stability threshold is crossed. For larger thermal sensitivities, however, the pulsating stability boundary evolves into a C-shaped curve in the disturbance-wavenumber/ pressure-sensitivity plane, indicating loss of stability to pulsating perturbations for all sufficiently large disturbance wavelengths. It is thus concluded, based on characteristic parameter values, that an equally likely form of hydrodynamic instability in liquid-propellant combustion is of a nonsteady, long-wave nature, distinct from the steady, cellular form originally predicted by Landau.

Pulsating Hydrodynamic Instability and Thermal Coupling in an Extended Landau/Levich Model of Liquid-Propellant Combustion. 1; Inviscid Analysis

NASA Technical Reports Server (NTRS)

Margolis, Stephen B.; Sacksteder, Kurt (Technical Monitor)

1999-01-01

Hydrodynamic (Landau) instability in combustion is typically associated with the onset of wrinkling of a flame surface, corresponding to the formation of steady cellular structures as the stability threshold is crossed. In the context of liquid-propellant combustion, such instability has recently been shown to occur for critical values of the pressure sensitivity of the burning rate and the disturbance wavenumber, significantly generalizing previous classical results for this problem that assumed a constant normal burning rate. Additionally, however, a pulsating form of hydrodynamic instability has been shown to occur as well, corresponding to the onset of temporal oscillations in the location of the liquid/gas interface. In the present work, we consider the realistic influence of a non-zero temperature sensitivity in the local burning rate on both types of stability thresholds. It is found that for sufficiently small values of this parameter, there exists a stable range of pressure sensitivities for steady, planar burning such that the classical cellular form of hydrodynamic instability and the more recent pulsating form of hydrodynamic instability can each occur as the corresponding stability threshold is crossed. For larger thermal sensitivities, however, the pulsating stability boundary evolves into a C-shaped curve in the (disturbance-wavenumber, pressure-sensitivity) plane, indicating loss of stability to pulsating perturbations for all sufficiently large disturbance wavelengths. It is thus concluded, based on characteristic parameter values, that an equally likely form of hydrodynamic instability in liquid-propellant combustion is of a non-steady, long-wave nature, distinct from the steady, cellular form originally predicted by Landau.

Evaluation of the Cytosorb™ Hemoadsorptive Column in a Pig Model of Severe Smoke and Burn Injury.

PubMed

Linden, Katharina; Scaravilli, Vittorio; Kreyer, Stefan F X; Belenkiy, Slava M; Stewart, Ian J; Chung, Kevin K; Cancio, Leopoldo C; Batchinsky, Andriy I

2015-11-01

Host inflammatory response to any form of tissue injury, including burn, trauma, or shock, has been well documented. After significant burns, cytokines can increase substantially within the first 24 h after injury and may contribute to subsequent organ failure. Hemoadsorption by cytokine-adsorbing columns may attenuate this maladaptive response, thereby improving outcomes. The aim of this study was to investigate the feasibility, technical safety, and efficacy of cytokine and myoglobin removal by early use of a cytokine absorbing column (CytoSorb) in a porcine model of smoke inhalation and burn injury. Anesthetized female Yorkshire pigs (n = 15) were injured by wood bark smoke inhalation and a 40% total body surface area deep burn and observed for 72 h or death. The animals were randomized to hemoadsorption treatment (n = 9) or a sham group (n = 6) before injury. A 6-h hemoadsorption or sham session was performed on days one, two, and three. Serum cytokines (IL-1b, IL-6, IL-8, IL-10, TNF-alpha) and myoglobin were measured systemically, locally in bronchoalveolar lavage fluid and also in circulating blood before and after the adsorbing column to evaluate single pass clearance by the device. Hemoadsorption caused significant removal of IL-1b, IL-6, IL-10, and myoglobin across the device mainly during the first run, ranging from 22% for IL-6 to 29% for IL-1b and 41% removal rates for myoglobin after 15  min of treatment. Systemic cytokine or myoglobin serum concentrations did not change. In a porcine model of smoke and burn injury, hemoadsorption using the CytoSorb cartridge did not result in significant systemic or pulmonary reductions in the measured cytokines or myoglobin despite efficient transmembrane reductions. Further investigations are needed to optimize the efficiency of mediator clearance to affect both circulating levels and clinically relevant outcomes.

A clinician's guide to the treatment of foot burns occurring in diabetic patients.

PubMed

Jones, Larry M; Coffey, Rebecca; Khandelwal, Sorabh; Atway, Said; Gordillo, Gayle; Murphy, Claire; Fries, Jody A; Dungan, Kathleen

2014-12-01

Diabetes mellitus affects 25.8 million Americans and is predicted to almost double by 2050. The presence of diabetes complicates hospital courses because of the microvascular complications associated with disease progression. Patients with diabetes represent 18.3% of annual burn admissions to our unit and 27% have burns to the feet. The purpose of this project was to develop an evidence-based guideline for care of the patient with diabetes and foot burns A multidisciplinary group was charged with developing an evidence-based guideline for the treatment of foot burns in patients with diabetes. Evidence was evaluated in the areas of diabetes, burn care, hyperbaric medicine, care of diabetic foot wounds and physical therapy. After guideline development and approval, key aspects were incorporated into order sets. Key aspects of this guideline are the ability to identify patients with undiagnosed diabetes, assess diabetic control, optimize glycemic and metabolic control, optimize burn wound management, treat microvascular disease, and provide education and a discharge plan. Evaluated outcomes are glycemic control, length of stay, complication rates, amputation rates, infection rates and the use of hyperbaric oxygen. Best outcomes for this high risk population will be attainable with an evidence based guideline. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

The Impact of a Universal Decolonization Protocol on Hospital-Acquired Methicillin-Resistant Staphylococcus aureus in a Burn Population.

PubMed

Johnson, Arthur T; Nygaard, Rachel M; Cohen, Ellie M; Fey, Ryan M; Wagner, Anne Lambert

Hospital-acquired (HA) methicillin-resistant Staphylococcus aureus (MRSA) is a leading cause of HA infections and a significant concern for burn centers. The use of 2% chlorhexidine-impregnated wipes and nasal mupirocin significantly decreases the rate of HA-MRSA in adult intensive care units. The aim of this study was to examine the impact of universal decolonization on the rate of MRSA conversion in an American Burn Association verified adult and pediatric burn center. Universal decolonization protocol consisting of daily chlorhexidine baths and a 5-day course of nasal mupirocin was implemented in the burn unit. MRSA screening both on admission and weekly and contact isolation practices were in place in pre-decolonization and post-decolonization periods. Patient data were analyzed 2 years before and 1 year after implementation of the protocol. The incidence rate of MRSA was significantly decreased after the implementation of the decolonization protocol (11.8 vs 1.0 per 1000 patient days, P < .001). Secondary to the loss of the skin barrier and suppressed immune systems, burn patients are at greater risk for invasive infection leading to severe complications and death. The prevalence of HA-MRSA at our institution's burn center was significantly decreased after the implementation of a universal decolonization protocol.

Nonlinear Burn Control and Operating Point Optimization in ITER

NASA Astrophysics Data System (ADS)

Boyer, Mark; Schuster, Eugenio

2013-10-01

Control of the fusion power through regulation of the plasma density and temperature will be essential for achieving and maintaining desired operating points in fusion reactors and burning plasma experiments like ITER. In this work, a volume averaged model for the evolution of the density of energy, deuterium and tritium fuel ions, alpha-particles, and impurity ions is used to synthesize a multi-input multi-output nonlinear feedback controller for stabilizing and modulating the burn condition. Adaptive control techniques are used to account for uncertainty in model parameters, including particle confinement times and recycling rates. The control approach makes use of the different possible methods for altering the fusion power, including adjusting the temperature through auxiliary heating, modulating the density and isotopic mix through fueling, and altering the impurity density through impurity injection. Furthermore, a model-based optimization scheme is proposed to drive the system as close as possible to desired fusion power and temperature references. Constraints are considered in the optimization scheme to ensure that, for example, density and beta limits are avoided, and that optimal operation is achieved even when actuators reach saturation. Supported by the NSF CAREER award program (ECCS-0645086).

Brief Communication: A Simplified Approach to Transient Convective Droplet Evaporation and Burning

NASA Technical Reports Server (NTRS)

Madooglu, K.; Karagozian, A. R.

1994-01-01

Empirical correlations for evaporation rates from single fuel droplets have existed since the 1930s. These correlations, which will be referred to in this article as Froessling/Ranz-Marshall types of correlations, are appropriate to the special cases of steady-state evaporation in the absence of chemical reaction. In a previous article by the authors, the quasi-steady evaporation and burning processes associated with a fuel drop in a convective environment are examined through a droplet model based on the boundary layer approach. For droplet Reynolds numbers of practical interest, this model produces very reasonable steady state as well as quasi-time-dependent droplet simulations, requiring relatively short computational times and yielding good agreement with the above-mentioned empirical correlations. The steady-state case, however, is usually relevant to practical combustor situations only when the drop has reached a nearly uniform temperature since the heating process of the drop cannot be considered to be quasi-steady. In the present study, the transient heating process of the droplet interior during evaporation and/or burning is taken into account, and thus calculations pertaining to the entire life-time of the droplet are carried out. It is of particular interest here to obtain simplified correlations to describe the transient behavior of evaporating and burning droplets; these may be incorporated with greater ease into spray calculations. Accordingly, we have chosen to use stagnation conditions in the present model in a modification of the Froessling/Ranz-Marshall correlations. These modified correlations, incorporating an effective transfer number, produce a fairly accurate representation of droplet evaporation and burning, while requiring only one tenth the computational effort used in a full boundary layer solution.

Long-Term Skeletal Muscle Mitochondrial Dysfunction is Associated with Hypermetabolism in Severely Burned Children.

PubMed

Porter, Craig; Herndon, David N; Børsheim, Elisabet; Bhattarai, Nisha; Chao, Tony; Reidy, Paul T; Rasmussen, Blake B; Andersen, Clark R; Suman, Oscar E; Sidossis, Labros S

2016-01-01

The long-term impact of burn trauma on skeletal muscle bioenergetics remains unknown. Here, the authors determined respiratory capacity and function of skeletal muscle mitochondria in healthy individuals and in burn victims for up to 2 years postinjury. Biopsies were collected from the m. vastus lateralis of 16 healthy men (26 ± 4 years) and 69 children (8 ± 5 years) with burns encompassing ≥30% of their total BSA. Seventy-nine biopsies were collected from cohorts of burn victims at 2 weeks (n = 18), 6 months (n = 18), 12 months (n = 25), and 24 months (n = 18) postburn. Hypermetabolism was determined by the difference in predicted and measured metabolic rate. Mitochondrial respiration was determined in saponin-permeabilized myofiber bundles. Outcomes were modeled by analysis of variance, with differences in groups assessed by Tukey-adjusted contrasts. Burn patients were hypermetabolic for up to 2 years postinjury. Coupled mitochondrial respiration was lower at 2 weeks (17 [8] pmol/sec/mg; P < .001), 6 months (41 [30] pmol/sec/mg; P = .03), and 12 months (35 [14] pmol/sec/mg; P < .001) postburn compared with healthy controls (58 [13] pmol/sec/mg). Coupled respiration was greater at 6, 12, and 24 months postburn vs 2 weeks postburn (P < .001). Mitochondrial adenosine diphosphate and oligomycin sensitivity (measures of coupling control) were lower at all time-points postburn vs control (P < .05), but greater at 6, 12, and 24 months postburn vs 2 weeks postburn (P < .05). Muscle mitochondrial respiratory capacity remains significantly lower in burn victims for 1-year postinjury. Mitochondrial coupling control is diminished for up to 2 years postinjury in burn victims, resulting in greater mitochondrial thermogenesis. These quantitative and qualitative derangements in skeletal muscle bioenergetics likely contribute to the long-term pathophysiological stress response to burn trauma.

LA50 in burn injuries.

PubMed

Seyed-Forootan, K; Karimi, H; Motevalian, S A; Momeni, M; Safari, R; Ghadarjani, M

2016-03-31

Burn injuries put a huge financial burden on patients and healthcare systems. They are the 8th leading cause of mortality and the 13th most common cause of morbidity in our country. We used data from our Burn Registry Program to evaluate risk factors for mortality and lethal area fifty percent (LA50) in all burn patients admitted over two years. We used multiple logistic regressions to identify risk factors for mortality. LA50 is a reliable aggregate index for hospital care quality and a good measure for comparing results, also with those of other countries. 28,690 burn patients sought medical attention in the Emergency Department, and 1721 of them were admitted. Male to female ratio was 1,75:1. 514 patients were under 15 years old. Median age was 25 (range: 3 months - 93 years). Overall, probability of death was 8.4%. LA50 was 62.31% (CI 95%: 56.57-70.02) for patients aged 15 and over and 72.52% (CI 95%: 61.01-100) for those under 15. In the final model, we found that Adjusted OR was significant for age, female sex, TBSA and inhalation injury (P < 0.05). LA50 values showed that children tolerate more extensive burns. Female sex, burn size, age and inhalation injury were the main risk factors for death. Authorities should pay special attention to these variables, especially in prevention programs, to reduce mortality and improve patient outcome. Children have better outcome than adults given equal burn size. Suicide rates are higher for women than men in our country.

Assessing the Efficacy of Restricting Access to Barbecue Charcoal for Suicide Prevention in Taiwan: A Community-Based Intervention Trial

PubMed Central

Chen, Ying-Yeh; Chen, Feng; Chang, Shu-Sen; Wong, Jacky; Yip, Paul S F

2015-01-01

Objective Charcoal-burning suicide has recently been spreading to many Asian countries. There have also been several cases involving this new method of suicide in Western countries. Restricting access to suicide means is one of the few suicide-prevention measures that have been supported by empirical evidence. The current study aims to assess the effectiveness of a community intervention program that restricts access to charcoal to prevent suicide in Taiwan. Methods and Findings A quasi-experimental design is used to compare method-specific (charcoal-burning suicide, non-charcoal-burning suicide) and overall suicide rates in New Taipei City (the intervention site, with a population of 3.9 million) with two other cities (Taipei City and Kaohsiung City, the control sites, each with 2.7 million residents) before (Jan 1st 2009- April 30th 2012) and after (May 1st 2012-Dec. 31st 2013) the initiation of a charcoal-restriction program on May 1st 2012. The program mandates the removal of barbecue charcoal from open shelves to locked storage in major retail stores in New Taipei City. No such restriction measure was implemented in the two control sites. Generalized linear regression models incorporating secular trends were used to compare the changes in method-specific and overall suicide rates before and after the initiation of the restriction measure. A simulation approach was used to estimate the number of lives saved by the intervention. Compared with the pre-intervention period, the estimated rate reduction of charcoal-burning suicide in New Taipei City was 37% (95% CI: 17%, 50%) after the intervention. Taking secular trends into account, the reduction was 30% (95% CI: 14%, 44%). No compensatory rise in non-charcoal-burning suicide was observed in New Taipei City. No significant reduction in charcoal-burning suicide was observed in the other two control sites. The simulation approach estimated that 91 (95%CI [55, 128]) lives in New Taipei City were saved during the 20 months of the intervention. Conclusion Our results demonstrate that the charcoal-restriction program reduced method-specific and overall suicides. This study provides strong empirical evidence that restricting the accessibility of common lethal methods of suicide can effectively reduce suicide rates. PMID:26305374

The Burn Rate of Calcium Sulfate Dihydrate-Aluminum Thermites.

PubMed

Govender, Desania Raquel; Focke, Walter Wilhelm; Tichapondwa, Shepherd Masimba; Cloete, William Edward

2018-05-29

The energetics of cast calcium sulfate dihydrate-aluminium thermites was investigated. The casts were prepared form water slurries with a solids content of xxx wt-%. The base case thermite comprised 60 wt-% calcium sulfate dihydrate as the oxidiser with 40 wt-% aluminium as fuel. The heat of hydration of the base case was 59 ± 8 kJkg-1 and the setting time was zzz min. The compressive strength reached 2.9 ± 0.2 MPa after three days drying in ambient air. The open air burn rate was 12.0 ± 1.6 mm s-1 and a maximum surface temperature of 1370 ± 64 °C was recorded with a pyrometer. Bomb calorimetry indicated an energy output of 8.0 ± 1.1 MJ kg-1, slightly lower than predicted by the EKVI thermodynamic simulation. Substitution of 10 wt-% of the oxidant with copper sulfate pentahydrate significantly decreased the setting time of the casts to about yyy min. The density of the castings was varied by either adding hollow sodium borosilicate glass spheres or by adding excess water during the casting process. The addition of the hollow glass spheres caused a decrease in the burning rate. The burning rate of the base case was not affected materially by the addition of excess water. However, it did increase the burning rate of the copper sulfate pentahydrate-modified thermite. Dehydration of the casts by thermal treatments at either 155 °C or 200 °C also led to significant increases in the burning rate.

An in vivo comparison of commonly used topical antimicrobials on skin graft healing after full-thickness burn injury.

PubMed

Abbas, Ozan L; Borman, Huseyin; Bahar, Taner; Ertaş, Nilgün M; Haberal, Mehmet

2015-01-01

Topical antimicrobials are frequently used for local control of infections in burn patients. It has been postulated that these agents retard wound healing. There are limited data about the effects of topical antimicrobial agents on skin graft healing. In this study, we aimed to evaluate the effects of nitrofurazone, 1% silver sulfadiazine, and povidone-iodine on skin graft healing. Forty male rats were used in this study. A meshed skin graft, placed on an excised burn wound, was used as a model to compare topical agents with a control group. Skin graft survival rates, closure of meshed graft interstices (based on physical parameters, namely epithelialization and wound contraction), and histological changes were analyzed. Graft take was more than 85% in all groups. There was no difference between the mean values of the percent graft survival for each group (P > .05). Epithelialization occurred significantly earlier in animals in the nitrofurazone group (P < .05). There was no significant difference between groups in wound contraction rates (P >.05). There was no histological difference between the biopsy specimens of skin grafts. In specimens obtained from the interstices of the meshed graft, no significant differences were found among the groups regarding the wound healing parameters (P > .05). We found that nitrofurazone, silver sulfadiazine, and povidone-iodine had no negative effect on graft healing and take in noncontaminated burn wounds.

Injury-related fear-avoidance and symptoms of posttraumatic stress in parents of children with burns.

PubMed

Willebrand, M; Sveen, J

2016-03-01

Parents of children with burns experience a range of psychological reactions and symptoms, and parents' health is known to impact children's health. So far, there is little research into potential mechanisms that maintain parents' symptoms. The aim was to investigate parental injury-related fear-avoidance, and its associations with injury severity and health measures. Parents (n=107) of children aged 0.4-18 years that sustained burns 0.1-9.0 years previously completed questionnaires on fear-avoidance, posttraumatic stress, and health of the child. Analyses showed that the average level of fear-avoidance was low and positively associated with measures of injury severity and parents' symptoms of posttraumatic stress, and negatively associated with parents' ratings of their child's health. In two separate multiple regressions with parents' symptoms of PTSD and the child's health as dependent variables, fear-avoidance made the largest contribution in both models while injury severity was non-significant. Results were not related to comorbid conditions of the child, scarring, or parent-related socio-demographic variables. In summary, injury-related fear-avoidance is more likely among parents whose children sustain more severe burns. In turn, fear-avoidance contributes significantly to parents' symptoms of PTSD and to poorer health ratings regarding the child, irrespective of injury severity or child comorbidity. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Impacts of brown carbon from biomass burning on surface UV and ozone photochemistry in the Amazon Basin

PubMed Central

Mok, Jungbin; Krotkov, Nickolay A.; Arola, Antti; Torres, Omar; Jethva, Hiren; Andrade, Marcos; Labow, Gordon; Eck, Thomas F.; Li, Zhanqing; Dickerson, Russell R.; Stenchikov, Georgiy L.; Osipov, Sergey; Ren, Xinrong

2016-01-01

The spectral dependence of light absorption by atmospheric particulate matter has major implications for air quality and climate forcing, but remains uncertain especially in tropical areas with extensive biomass burning. In the September-October 2007 biomass-burning season in Santa Cruz, Bolivia, we studied light absorbing (chromophoric) organic or “brown” carbon (BrC) with surface and space-based remote sensing. We found that BrC has negligible absorption at visible wavelengths, but significant absorption and strong spectral dependence at UV wavelengths. Using the ground-based inversion of column effective imaginary refractive index in the range 305–368 nm, we quantified a strong spectral dependence of absorption by BrC in the UV and diminished ultraviolet B (UV-B) radiation reaching the surface. Reduced UV-B means less erythema, plant damage, and slower photolysis rates. We use a photochemical box model to show that relative to black carbon (BC) alone, the combined optical properties of BrC and BC slow the net rate of production of ozone by up to 18% and lead to reduced concentrations of radicals OH, HO2, and RO2 by up to 17%, 15%, and 14%, respectively. The optical properties of BrC aerosol change in subtle ways the generally adverse effects of smoke from biomass burning. PMID:27833145

Incidence and cost of non-fatal burns in Iran: a nationwide population-based study.

PubMed

Abouie, Abolfazl; Salamati, Payman; Hafezi-Nejad, Nima; Rahimi-Movaghar, Afarin; Saadat, Soheil; Amin-Esmaeili, Masoumeh; Sharifi, Vandad; Hajebi, Ahmad; Rahimi-Movaghar, Vafa

2018-03-01

To determine the incidence and cost of non-fatal burns in Iran; this cross-sectional household survey of a nationally representative sample of 15-64 years old was conducted. Through face-to-face interviews and telephone calls, the data on the demographics, history and cost of burns were collected. The annual incidence rate of burns was estimated 129.85 per 1000 population. Burns occurred higher in younger age, female gender and urban residency. The most common burn description was as follows: unpaid work (activity during burn), home (place of burn), heat and hot substances (mechanism of burn) and upper limb (site of burn). The average total cost of burn includes victims seeking medical care was US$124 per case. The main findings of this study suggest that burns are a major public health concern in Iran. To stop this important health issue, a national program for burn prevention and education must be developed.

Influence of fire on black-tailed prairie dog colony expansion in shortgrass steppe

USGS Publications Warehouse

Augustine, D.J.; Cully, J.F.; Johnson, T.L.

2007-01-01

Factors influencing the distribution and abundance of black-tailed prairie dog (Cynomys ludovicianus) colonies are of interest to rangeland managers because of the significant influence prairie dogs can exert on both livestock and biodiversity. We examined the influence of 4 prescribed burns and one wildfire on the rate and direction of prairie dog colony expansion in shortgrass steppe of southeastern Colorado. Our study was conducted during 2 years with below-average precipitation, when prairie dog colonies were expanding throughout the study area. Under these dry conditions, the rate of black-tailed prairie dog colony expansion into burned grassland (X?? = 2.6 ha??100-m perimeter-1??y-1; range = 0.8-5.9 ha??100-m perimeter-1??y-1; N = 5 colonies) was marginally greater than the expansion rate into unburned grassland (X?? =1.3 ha??100-m perimeter-1??y-1; range = 0.2-4.9 ha??100-m perimeter-1??y-1; N = 23 colonies; P = 0.066). For 3 colonies that were burned on only a portion of their perimeter, we documented consistently high rates of expansion into the adjacent burned grassland (38%-42% of available burned habitat colonized) but variable expansion rates into the adjacent unburned grassland (2%-39% of available unburned habitat colonized). While our results provide evidence that burning can increase colony expansion rate even under conditions of low vegetative structure, this effect was minor at the scale of the overall colony complex because some unburned colonies were also able to expand at high rates. This result highlights the need to evaluate effects of fire on colony expansion during above-average rainfall years, when expansion into unburned grassland may be considerably lower.

Virtual reality pain control during burn wound debridement of combat-related burn injuries using robot-like arm mounted VR goggles.

PubMed

Maani, Christopher V; Hoffman, Hunter G; Morrow, Michelle; Maiers, Alan; Gaylord, Kathryn; McGhee, Laura L; DeSocio, Peter A

2011-07-01

This is the first controlled study to explore whether adjunctive immersive virtual reality (VR) can reduce excessive pain of soldiers with combat-related burn injuries during wound debridement. Patients were US soldiers burned in combat attacks involving explosive devices in Iraq or Afghanistan. During the same wound care session using a within-subject experimental design, 12 patients received half of their severe burn wound cleaning procedure (~6 minutes) with standard of care pharmacologies and half while in VR (treatment order randomized). Three 0 to 10 Graphic Rating Scale pain scores for each of the treatment conditions served as the primary variables. Patients reported significantly less pain when distracted with VR. "Worst pain" (pain intensity) dropped from 6.25 of 10 to 4.50 of 10. "Pain unpleasantness" ratings dropped from "moderate" (6.25 of 10) to "mild" (2.83 of 10). "Time spent thinking about pain" dropped from 76% during no VR to 22% during VR. Patients rated "no VR" as "no fun at all" (<1 of 10) and rated VR as "pretty fun" (7.5 of 10). Follow-up analyses showed VR was especially effective for the six patients who scored 7 of 10 or higher (severe to excruciating) on the "worst pain" (pain intensity) ratings. These preliminary results provide the first evidence from a controlled study that adjunctive immersive VR reduced pain of patients with combat-related burn injuries during severe burn wound debridement. Pain reduction during VR was greatest in patients with the highest pain during no VR. These patients were the first to use a unique custom robot-like arm mounted VR goggle system.

Virtual Reality Pain Control During Burn Wound Debridement of Combat-Related Burn Injuries Using Robot-Like Arm Mounted VR Goggles

PubMed Central

Maani, Christopher V.; Hoffman, Hunter G.; Morrow, Michelle; Maiers, Alan; Gaylord, Kathryn; McGhee, Laura L.; DeSocio, Peter A.

2015-01-01

Background This is the first controlled study to explore whether adjunctive immersive virtual reality (VR) can reduce excessive pain of soldiers with combat-related burn injuries during wound debridement. Methods Patients were US soldiers burned in combat attacks involving explosive devices in Iraq or Afghanistan. During the same wound care session using a within-subject experimental design, 12 patients received half of their severe burn wound cleaning procedure (∼6 minutes) with standard of care pharmacologies and half while in VR (treatment order randomized). Three 0 to 10 Graphic Rating Scale pain scores for each of the treatment conditions served as the primary variables. Results Patients reported significantly less pain when distracted with VR. “Worst pain” (pain intensity) dropped from 6.25 of 10 to 4.50 of 10. “Pain unpleasantness” ratings dropped from “moderate” (6.25 of 10) to “mild” (2.83 of 10). “Time spent thinking about pain” dropped from 76% during no VR to 22% during VR. Patients rated “no VR” as “no fun at all” (<1 of 10) and rated VR as “pretty fun” (7.5 of 10). Follow-up analyses showed VR was especially effective for the six patients who scored 7 of 10 or higher (severe to excruciating) on the “worst pain” (pain intensity) ratings. Conclusions These preliminary results provide the first evidence from a controlled study that adjunctive immersive VR reduced pain of patients with combat-related burn injuries during severe burn wound debridement. Pain reduction during VR was greatest in patients with the highest pain during no VR. These patients were the first to use a unique custom robot-like arm mounted VR goggle system. PMID:21795888

Basic Burns Management E-Learning: A New Teaching Tool.

PubMed

Egro, Francesco M

Burns teaching is organized only in a few medical schools in the United Kingdom. An e-learning tutorial was developed with the objective of incorporating burns teaching within the medical school curriculum. A 33-webpage e-learning was created, covering topics such as local and general response to burns, assessment of burns, first aid, primary and secondary survey, and referral guidelines. Medical student satisfaction was then evaluated using a 12-question feedback survey rated based on a Likert scale from 1 (very poor) to 5 (very good). The 12-question survey was completed by a total of 18 medical students ranging from second to fourth years (second = 17%, third = 22%, fourth = 61%). While only a couple of students had received prior burns teaching, 50% of the cohort had an interest to pursue surgery as a career. The majority of students (72%) would be interested to have an e-learning module on basic burns management in their medical curriculum. The means of all domains specific to the e-learning were rated as "good" or "very good." Students' rating for ease of use was 87%, usefulness was 88%, relevance to the medical curriculum was 90%, clarity and quality of content were 78% and 83%, respectively, design was 79%, and the overall satisfaction with this e-learning was 87%. The "Basic Burns Management" e-learning tutorial can provide an efficient and effective means of information delivery to medical students and junior doctors, allowing easy and fast incorporation of burns teaching within the medical curriculum and in other medical teaching settings.

Epidemiology of a decade of Pediatric fatal burns in Colombia, South America.

PubMed

Aldana, Maria Cristina del Rosario; Navarrete, Norberto

2015-11-01

Burns represent a serious problem around the world especially in low- and middle-income countries. The aim was to determine the epidemiological characteristics, causes and mortality rate of burn deaths in the Colombian pediatric population as well as to guide future education and prevention programs. We conducted an observational, analytical, retrospective population-based study. It was based upon official death certificate data using diagnosis codes for burns (scalds, thermal, electrical, intentional self-harm and not specified), that occurred between January 1, 2000 and December 31, 2009. Official death certificates of the pediatric population of up to 15 years of age were obtained from the National Administrative Department of Statistics. A total of 1197 fatal pediatric injuries related to burns were identified. The crude and adjusted mortality rate for burns in the pediatric population in Colombia during the length of the study was 0.899 and 0.912 per 100,000, respectively. The mortality rate tended to decrease (-5.17% annual) during the duration of the study. Children under 5 years of age were the most affected group (59.5%). Almost half of them died before arriving at a health facility (47.1%). Fire is the principal cause of death attributable to burns in Colombia, followed by electric burns and hot liquids. This is a first step study in researching the epidemiological features of pediatric deaths after burns. The Public Health's strategies should be oriented toward community awareness about these kind of injuries, and to teach children and families about risk factors and first aid. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Pediatric burns: Kids' Inpatient Database vs the National Burn Repository.

PubMed

Soleimani, Tahereh; Evans, Tyler A; Sood, Rajiv; Hartman, Brett C; Hadad, Ivan; Tholpady, Sunil S

2016-04-01

Burn injuries are one of the leading causes of morbidity and mortality in young children. The Kids' Inpatient Database (KID) and National Burn Repository (NBR) are two large national databases that can be used to evaluate outcomes and help quality improvement in burn care. Differences in the design of the KID and NBR could lead to differing results affecting resultant conclusions and quality improvement programs. This study was designed to validate the use of KID for burn epidemiologic studies, as an adjunct to the NBR. Using the KID (2003, 2006, and 2009), a total of 17,300 nonelective burn patients younger than 20 y old were identified. Data from 13,828 similar patients were collected from the NBR. Outcome variables were compared between the two databases. Comparisons revealed similar patient distribution by gender, race, and burn size. Inhalation injury was more common among the NBR patients and was associated with increased mortality. The rates of respiratory failure, wound infection, cellulitis, sepsis, and urinary tract infection were higher in the KID. Multiple regression analysis adjusting for potential confounders demonstrated similar mortality rate but significantly longer length of stay for patients in the NBR. Despite differences in the design and sampling of the KID and NBR, the overall demographic and mortality results are similar. The differences in complication rate and length of stay should be explored by further studies to clarify underlying causes. Investigations into these differences should also better inform strategies to improve burn prevention and treatment. Copyright © 2016 Elsevier Inc. All rights reserved.

Effects of high shock pressures and pore morphology on hot spot mechanisms in HMX

NASA Astrophysics Data System (ADS)

Springer, H. K.; Tarver, C. M.; Bastea, S.

2017-01-01

The shock initiation and detonation behavior of heterogeneous solid explosives is governed by its microstructure and reactive properties. New additive manufacturing techniques offer unprecedented control of explosive microstructures previously impossible, enabling us to develop novel explosives with tailored shock sensitivity and detonation properties. Since microstructure-performance relationships are not well established for explosives, there is little material design guidance for these manufacturing techniques. In this study, we explore the effects of high shock pressures (15-38 GPa) with long shock durations and different pore morphologies on hot spot mechanisms in HMX. HMX is chosen as the model material because we have experimental data on many of the chemical-thermal-mechanical properties required for pore collapse simulations. Our simulations are performed using the multi-physics arbitrary Lagrangian Eulerian finite element hydrocode, ALE3D, with Cheetah-based models for the unreacted and the product equation-of-states. We use a temperature-dependent specific heat with the unreacted equation-of-state and a temperature-dependent viscosity model to ensure accurate shock temperatures for subsequent chemistry. The Lindemann Law model is used for shock melting in HMX. In contrast to previous pore collapse studies at lower shock pressures (≤10 GPa) in HMX and shorter post-collapse burning times, our calculations show that shock melting occurs above 15 GPa due to higher bulk heating and a prominent elongated ("jet-like") hot spot region forms at later times. The combination of the elongated, post-collapse hot spot region and the higher bulk heating with increasing pressure dramatically increases the growth rate of reaction. Our calculations show that the reaction rate, dF/dt, increases with increasing shock pressure. We decompose the reaction rate into ignition ((dF/dt)ig) and growth ((dF/dt)gr) phases to better analyze our results. We define the ignition phase to primarily include pore collapse and growth phase to primarily include post-collapse grain burning. We are able to track late-time, post-collapse burning due to the unique loading conditions employed in these calculations. We find that (dF/dt)gr > (dF/dt)ig for all pressures considered. (dF/dt)gr changes more significantly from 25 to 38 GPa (from 0.05/µs to >10-100/µs) than from 15 to 25 GPa (from 0.005/µs to 0.05/µs). There is a three order-of-magnitude difference in the reaction from 15 to 38 GPa just after pore collapse. This is qualitatively consistent with fitting the (macroscopic) Ignition and Growth model to high pressure shock initiation data, where much larger reaction fractions are needed to capture the early stages of reaction. Calculated burn rates demonstrate better agreement with data at intermediate times in the growth phase for 15 to 25 GPa and late times for 30 GPa then at any time in the growth phase for 38 GPa. Our calculations are much higher than burn rate data at the earliest times in the growth phase for all pressures, which may reflect the higher localized pressures and temperatures just after pore collapse in the ignition phase. Our calculations with spherical, conical, and elliptical pores show that the influence of morphology on reaction rate is pressure dependent and the most influential pore shapes at lower pressures aren't the same at higher pressures in the regime studied. Altogether these studies provide the basis for developing microstructure-aware models that can be used to design new explosives with optimal performance-safety characteristics. Such models can be used to guide additive manufacturing of explosives and fully exploit their disruptive nature.

Convective Heat Transfer Scaling of Ignition Delay and Burning Rate with Heat Flux and Stretch Rate in the Equivalent Low Stretch Apparatus

NASA Technical Reports Server (NTRS)

Olson, Sandra

2011-01-01

To better evaluate the buoyant contributions to the convective cooling (or heating) inherent in normal-gravity material flammability test methods, we derive a convective heat transfer correlation that can be used to account for the forced convective stretch effects on the net radiant heat flux for both ignition delay time and burning rate. The Equivalent Low Stretch Apparatus (ELSA) uses an inverted cone heater to minimize buoyant effects while at the same time providing a forced stagnation flow on the sample, which ignites and burns as a ceiling fire. Ignition delay and burning rate data is correlated with incident heat flux and convective heat transfer and compared to results from other test methods and fuel geometries using similarity to determine the equivalent stretch rates and thus convective cooling (or heating) rates for those geometries. With this correlation methodology, buoyant effects inherent in normal gravity material flammability test methods can be estimated, to better apply the test results to low stretch environments relevant to spacecraft material selection.

Expression and activity levels of chymase in mast cells of burn wound tissues increase during the healing process in a hamster model.

PubMed

Dong, Xianglin; Xu, Tao; Ma, Shaolin; Wen, Hao

2015-06-01

The present study aimed to investigate the changes in the expression levels and activity of mast cell chymase in the process of burn wound healing in a hamster model of deep second-degree burn. The hamster model was established by exposing a ~3 cm diameter area of bare skin to hot water (75°C) for 0, 6, 8, 10 or 12 sec. Tissue specimens were collected 24 h after burning and histological analysis revealed that hot water contact for 12 sec was required to produce a deep second-degree burn. Quantitative polymerase chain reaction and a radioimmunoassay were used to the determine changes in chymase mRNA expression levels and activity. The mRNA expression levels and activity of chymase were increased in the burn wound tissues when compared with the normal skin. However, no statistically significant differences were observed in mast cell chymase activity amongst the various post-burn stages. Chymase mRNA expression levels peaked at day 1 post-burn, subsequently decreasing at days 3 and 7 post-burn and finally increasing again at day 14 post-burn. In summary, a hamster model of deep second-degree burn can be created by bringing the skin into contact with water at 75°C for 12 sec. Furthermore, the mRNA expression levels and activity of chymase in the burn wound tissues increased when compared with those in normal skin tissues.

Expression and activity levels of chymase in mast cells of burn wound tissues increase during the healing process in a hamster model

PubMed Central

DONG, XIANGLIN; XU, TAO; MA, SHAOLIN; WEN, HAO

2015-01-01

The present study aimed to investigate the changes in the expression levels and activity of mast cell chymase in the process of burn wound healing in a hamster model of deep second-degree burn. The hamster model was established by exposing a ~3 cm diameter area of bare skin to hot water (75°C) for 0, 6, 8, 10 or 12 sec. Tissue specimens were collected 24 h after burning and histological analysis revealed that hot water contact for 12 sec was required to produce a deep second-degree burn. Quantitative polymerase chain reaction and a radioimmunoassay were used to the determine changes in chymase mRNA expression levels and activity. The mRNA expression levels and activity of chymase were increased in the burn wound tissues when compared with the normal skin. However, no statistically significant differences were observed in mast cell chymase activity amongst the various post-burn stages. Chymase mRNA expression levels peaked at day 1 post-burn, subsequently decreasing at days 3 and 7 post-burn and finally increasing again at day 14 post-burn. In summary, a hamster model of deep second-degree burn can be created by bringing the skin into contact with water at 75°C for 12 sec. Furthermore, the mRNA expression levels and activity of chymase in the burn wound tissues increased when compared with those in normal skin tissues. PMID:26136958

Ignition transient analysis of solid rocket motor

NASA Technical Reports Server (NTRS)

Han, Samuel S.

1990-01-01

To predict pressure-time and thrust-time behavior of solid rocket motors, a one-dimensional numerical model is developed. The ignition phase of solid rocket motors (time less than 0.4 sec) depends critically on complex interactions among many elements, such as rocket geometry, heat and mass transfer, flow development, and chemical reactions. The present model solves the mass, momentum, and energy equations governing the transfer processes in the rocket chamber as well as the attached converging-diverging nozzle. A qualitative agreement with the SRM test data in terms of head-end pressure gradient and the total thrust build-up is obtained. Numerical results show that the burning rate in the star-segmented head-end section and the erosive burning are two important parameters in the ignition transient of the solid rocket motor (SRM).

Heterogeneous propellant internal ballistics: criticism and regeneration

NASA Astrophysics Data System (ADS)

Glick, R. L.

2011-10-01

Although heterogeneous propellant and its innately nondeterministic, chemically discrete morphology dominates applications, ballisticcharacterization deterministic time-mean burning rate and acoustic admittance measures' absence of explicit, nondeterministic information requires homogeneous propellant with a smooth, uniformly regressing burning surface: inadequate boundary conditions for heterogeneous propellant grained applications. The past age overcame this dichotomy with one-dimensional (1D) models and empirical knowledge from numerous, adequately supported motor developments and supplementary experiments. However, current cost and risk constraints inhibit this approach. Moreover, its fundamental science approach is more sensitive to incomplete boundary condition information (garbage-in still equals garbage-out) and more is expected. This work critiques this situation and sketches a path forward based on enhanced ballistic and motor characterizations in the workplace and approximate model and apparatus developments mentored by CSAR DNS capabilities (or equivalent).

Modeling biomass burning over the South, South East and East Asian Monsoon regions using a new, satellite constrained approach

NASA Astrophysics Data System (ADS)

Lan, R.; Cohen, J. B.

2017-12-01

Biomass burning over the South, South East and East Asian Monsoon regions, is a crucial contributor to the total local aerosol loading. Furthermore, the impact of the ITCZ, and Monsoonal circulation patterns coupled with complex topography also have a prominent impact on the aerosol loading throughout much of the Northern Hemisphere. However, at the present time, biomass burning emissions are highly underestimated over this region, in part due to under-reported emissions in space and time, and in part due to an incomplete understanding of the physics and chemistry of the aerosols emitted in fires and formed downwind from them. Hence, a better understanding of the four-dimensional source distribution, plume rise, and in-situ processing, in particular in regions with significant quantities of urban air pollutants, is essential to advance our knowledge of this problem. This work uses a new modeling methodology based on the simultaneous constraints of measured AOD and some trace gasses over the region. The results of the 4-D constrained emissions are further expanded upon using different fire plume height rise and in-situ processing assumptions. Comparisons between the results and additional ground-based and remotely sensed measurements, including AERONET, CALIOP, and NOAA and other ground networks are included. The end results reveal a trio of insights into the nonlinear processes most-important to understand the impacts of biomass burning in this part of the world. Model-measurement comparisons are found to be consistent during the typical burning years of 2016. First, the model performs better under the new emissions representations, than it does using any of the standard hotspot based approaches currently employed by the community. Second, long range transport and mixing between the boundary layer and free troposphere contribute to the spatial-temporal variations. Third, we indicate some source regions that are new, either because of increased urbanization, or of regions being burned at significantly higher rates than previously known. These findings, however, are consistent with the current rapid economic development and population movement throughout South, South East and East Asia, as well as independent studies which have observed long-range transport of smoke throughout portions of this region.

[Epidemiological changes in burned children. A 10-year follow-up].

PubMed

Rojas Goldsack, María de Los Ángeles; Saavedra Opazo, Rolando; Vicencio Pezo, Paulina; Solís Flores, Fresia

2016-01-01

The aim of the study was to compare the incidence and epidemiological characteristics of burns suffered by children in a district of Santiago of Chile over a period of ten years. An analytical study was conducted by checking through the medical files of children under 15 years of age from Pudahuel district who were admitted with burns to the Santiago Aid to Burned Children Corporation (COANIQUEM) during 2011. A comparison was made with the results obtained in a similar study performed in the same district in 2001. In 2011, 440 children were admitted, with an incidence rate of 700/100,000 <15 years old (95% CI: 635-765), a decrease of 25% compared to 2001(Incidence rate of 933/100,000; 95% CI: 856-1010). There were 52% males, 64.5% under 5 years old of age, 88% burned at home, or at other houses where they are been taking care of. There was a significant change in the causative agent, and included, increasing by their relative importance; hot objects (27.1%). The mechanism that mostly increased in occurrence were contact with stoves or heaters, and also emerge that caused by hair iron, and motorcycle exhaust. The most common location was the hand, increasing by 30.8%, and 66.4% showed an extension of the burn of <1% total body surface area (2001, 61%). A significant decline of 54% of deep burns was observed, and 23.2% were admitted to rehabilitation, a similar proportion to 2001. The rate of hospitalization and/or skin graft decreased from 104/100,000 to 62/100,000<15 years old (95% CI: 43-82). Burns incidence has decreased. Hot objects are now the main causal agent. The decrease in the rate of hospitalization and/or graft indicates a lower severity of burns. Copyright © 2015 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

Initial Observations on the Burning of an Ethanol Droplet in Microgravity

NASA Technical Reports Server (NTRS)

Kazakov, Andrei; Urban, Bradley; Conley, Jordan; Dryer, Frederick L.; Ferkul, Paul (Technical Monitor)

1999-01-01

Combustion of liquid ethanol represents an important system both from fundamental and practical points of view, Ethanol is currently being used as an additive to gasoline in order to reduce carbon monoxide and particulate emissions as well as to improve the fuel octane rating. A detailed physical understanding of liquid ethanol combustion is therefore necessary to achieve an optimal performance of such fuel blends in practical conditions. Ethanol is also a relatively simple model compound suitable for investigation of important combustion characteristics typical of more complex fuels. In particular, ethanol has been proposed for studies of sooting behavior during droplet burning. The sooting nature of ethanol has pressure sensitivities similar to that of n-heptane, but shifted to a higher range of pressures (1-3 atm). Additionally, liquid ethanol is miscible with water produced during its combustion forming mixtures with azeotropic behavior, a phenomenon important for understanding multi-component, liquid fuel combustion. In this work, we present initial results obtained in a series of recent space-based experiments and develop a detailed model describing the burning of ethanol droplet in microgravity.

Using Logistic Regression to Predict the Probability of Debris Flows in Areas Burned by Wildfires, Southern California, 2003-2006

USGS Publications Warehouse

Rupert, Michael G.; Cannon, Susan H.; Gartner, Joseph E.; Michael, John A.; Helsel, Dennis R.

2008-01-01

Logistic regression was used to develop statistical models that can be used to predict the probability of debris flows in areas recently burned by wildfires by using data from 14 wildfires that burned in southern California during 2003-2006. Twenty-eight independent variables describing the basin morphology, burn severity, rainfall, and soil properties of 306 drainage basins located within those burned areas were evaluated. The models were developed as follows: (1) Basins that did and did not produce debris flows soon after the 2003 to 2006 fires were delineated from data in the National Elevation Dataset using a geographic information system; (2) Data describing the basin morphology, burn severity, rainfall, and soil properties were compiled for each basin. These data were then input to a statistics software package for analysis using logistic regression; and (3) Relations between the occurrence or absence of debris flows and the basin morphology, burn severity, rainfall, and soil properties were evaluated, and five multivariate logistic regression models were constructed. All possible combinations of independent variables were evaluated to determine which combinations produced the most effective models, and the multivariate models that best predicted the occurrence of debris flows were identified. Percentage of high burn severity and 3-hour peak rainfall intensity were significant variables in all models. Soil organic matter content and soil clay content were significant variables in all models except Model 5. Soil slope was a significant variable in all models except Model 4. The most suitable model can be selected from these five models on the basis of the availability of independent variables in the particular area of interest and field checking of probability maps. The multivariate logistic regression models can be entered into a geographic information system, and maps showing the probability of debris flows can be constructed in recently burned areas of southern California. This study demonstrates that logistic regression is a valuable tool for developing models that predict the probability of debris flows occurring in recently burned landscapes.

Development of Erosive Burning Models for CFD Predictions of Solid Rocket Motor Internal Environments

NASA Technical Reports Server (NTRS)

Wang, Qun-Zhen

2003-01-01

Four erosive burning models, equations (11) to (14). are developed in this work by using a power law relationship to correlate (1) the erosive burning ratio and the local velocity gradient at propellant surfaces; (2) the erosive burning ratio and the velocity gradient divided by centerline velocity; (3) the erosive burning difference and the local velocity gradient at propellant surfaces; and (4) the erosive burning difference and the velocity gradient divided by centerline velocity. These models depend on the local velocity gradient at the propellant surface (or the velocity gradient divided by centerline velocity) only and, unlike other empirical models, are independent of the motor size. It was argued that, since the erosive burning is a local phenomenon occurring near the surface of the solid propellant, the erosive burning ratio should be independent of the bore diameter if it is correlated with some local flow parameters such as the velocity gradient at the propellant surface. This seems to be true considering the good results obtained by applying these models, which are developed from the small size 5 inch CP tandem motor testing, to CFD simulations of much bigger motors.

Early anticoagulation therapy for severe burns complicated by inhalation injury in a rabbit model

PubMed Central

Fu, Zhong-Hua; Guo, Guang-Hua; Xiong, Zhen-Fang; Liao, Xincheng; Liu, Ming-Zhuo; Luo, Jinhua

2017-01-01

The aim of the present study was to determine the effects of early anticoagulation treatment on severe burns complicated by inhalation injury in a rabbit model. Under anesthetization, an electrical burns instrument (100°C) was used to scald the backs of rabbits for 15 sec, which established a 30% III severe burns model. Treatment of the rabbits with early anticoagulation effectively improved the severe burns complicated by inhalation injury-induced lung injury, reduced PaO2, PaCO2 and SPO2 levels, suppressed the expression of tumor necrosis factor-α, interleukin (IL)-1β and IL-6, and increased the activity of IL-10. In addition, it was found that early anticoagulation treatment effectively suppressed the activities of caspase-3 and caspase-9, upregulated the protein expression of vascular endothelial growth factor (VEGF) and decreased the protein expression of protease-activated receptor 1 (PAR1) in the severe burns model. It was concluded that early anticoagulation treatment affected the severe burns complicated by inhalation injury in a rabbit model through the upregulation of VEGF and downregulation of PAR1 signaling pathways. Thus, early anticoagulation is a potential therapeutic option for severe burns complicated by inhalation injury. PMID:28944866

A review of negative-pressure wound therapy in the management of burn wounds.

PubMed

Kantak, Neelesh A; Mistry, Riyam; Halvorson, Eric G

2016-12-01

Negative pressure has been employed in various aspects of burn care and the aim of this study was to evaluate the evidence for each of those uses. The PubMed and Cochrane CENTRAL databases were queried for articles in the following areas: negative pressure as a dressing for acute burns, intermediate treatment prior to skin grafting, bolster for skin autografts, dressing for integration of dermal substitutes, dressing for skin graft donor sites, and integrated dressing in large burns. Fifteen studies met our inclusion criteria. One study showed negative pressure wound therapy improved perfusion in acute partial-thickness burns, 8 out of 9 studies showed benefits when used as a skin graft bolster dressing, 1 out of 2 studies showed improved rate of revascularization when used over dermal substitutes, and 1 study showed increased rate of re-epithelialization when used over skin graft donor sites. Negative pressure can improve autograft take when used as a bolster dressing. There is limited data to suggest that it may also improve the rate of revascularization of dermal substitutes and promote re-epithelialization of skin graft donor sites. Other uses suggested by studies that did not meet our inclusion criteria include improving vascularity in acute partial-thickness burns and as an integrated dressing for the management of large burns. Further studies are warranted for most clinical applications to establish negative pressure as an effective adjunct in burn wound care. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Propagation of Reactions in Thermally-damaged PBX-9501

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tringe, J W; Glascoe, E A; Kercher, J R

A thermally-initiated explosion in PBX-9501 (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) is observed in situ by flash x-ray imaging, and modeled with the LLNL multi-physics arbitrary-Lagrangian-Eulerian code ALE3D. The containment vessel deformation provides a useful estimate of the reaction pressure at the time of the explosion, which we calculate to be in the range 0.8-1.4 GPa. Closely-coupled ALE3D simulations of these experiments, utilizing the multi-phase convective burn model, provide detailed predictions of the reacted mass fraction and deflagration front acceleration. During the preinitiation heating phase of these experiments, the solid HMX portion of the PBX-9501 undergoes a {beta}-phase to {delta}-phase transition which damages the explosivemore » and induces porosity. The multi-phase convective burn model results demonstrate that damaged particle size and pressure are critical for predicting reaction speed and violence. In the model, energetic parameters are taken from LLNL's thermochemical-kinetics code Cheetah and burn rate parameters from Son et al. (2000). Model predictions of an accelerating deflagration front are in qualitative agreement with the experimental images assuming a mode particle diameter in the range 300-400 {micro}m. There is uncertainty in the initial porosity caused by thermal damage of PBX-9501 and, thus, the effective surface area for burning. To better understand these structures, we employ x-ray computed tomography (XRCT) to examine the microstructure of PBX-9501 before and after thermal damage. Although lack of contrast between grains and binder prevents the determination of full grain size distribution in this material, there are many domains visible in thermally damaged PBX-9501 with diameters in the 300-400 {micro}m range.« less

Direct Radiative Impacts of Central American Biomass Burning Smoke Aerosols: Analysis from a Coupled Aerosol-Radiation-Meteorology Model RAMS-AROMA

NASA Astrophysics Data System (ADS)

Wang, J.; Christopher, S. A.; Nair, U. S.; Reid, J. S.; Prins, E. M.

2005-12-01

Considerable efforts including various field experiments have been carried out in the last decade for studying the regional climatic impact of smoke aerosols produced by biomass burning activities in Africa and South America. In contrast, only few investigations have been conducted for Central American Biomass Burning (CABB) region. Using a coupled aerosol-radiation-meteorology model called RAMS-AROMA together with various ground-based observations, we present a comprehensive analysis of the smoke direct radiative impacts on the surface energy budget, boundary layer evolution, and e precipitation process during the CABB events in Spring 2003. Quantitative estimates are also made regarding the transboundary carbon mass to the U.S. in the form of smoke particles. Buult upon the Regional Atmospheric Modeling System (RAMS) mesoscale model, the RAMS AROMA has several features including Assimilation and Radiation Online Modeling of Aerosols (AROMA) algorithms. The model simulates smoke transport by using hourly smoke emission inventory from the Fire Locating and Modeling of Burning Emissions (FLAMBE) geostationary satellite database. It explicitly considers the smoke effects on the radiative transfer at each model time step and model grid, thereby coupling the dynamical processes and aerosol transport. Comparison with ground-based observation show that the simulation realistically captured the smoke transport timeline and distribution from daily to hourly scales. The effects of smoke radiative extinction on the decrease of 2m air temperature (2mT), diurnal temperature range (DTR), and boundary layer height over the land surface are also quantified. Warming due to smoke absorption of solar radiation can be found in the lower troposphere over the ocean, but not near the underlying land surface. The increase of boundary layer stability produces a positive feedback where more smoke particles are trapped in the lower boundary layer. These changes in temperature, surface energy budget and the atmospheric lapse rate have important ramification for the simulation of precipitations.

Aromatherapy massage seems to enhance relaxation in children with burns: an observational pilot study.

PubMed

O'Flaherty, Linda-Anne; van Dijk, Monique; Albertyn, Rene; Millar, Alastair; Rode, Heinz

2012-09-01

This observational pilot study investigated effects of aromatherapy massage in paediatric burn patients. The setting was a 17 beds level I burn unit in Cape Town, South Africa. Between January and October 2009 heart rates and respiratory rates of patients who underwent aromatherapy massage sessions were read before and after the sessions. Primary outcomes were decline in heart rates and respiratory rates, a sign of relaxation. Behavioural responses (sleep/awake state, facial expression, body posture) were documented as secondary outcomes. A convenience sample of 71 paediatric burn patients (median age 3 years) underwent a total of 126 massage sessions. Mean heart rate decreased significantly from 118 (SD 20) to 109 (SD 21), t=9.8, p<0.001. Mean respiratory rate decreased significantly from 34 (SD 8) to 30 (SD 8), t=10.2, p<0.001. Most massage sessions (92.8%) elicited positive behaviour to the massage, e.g. the child fell asleep, calmed or asked to continue. Nine patients (7.2%) with a median age of 15 months who underwent a single massage session did not show positive behaviour but cried, wriggled or were distressed. Aromatherapy massage seems to be a helpful nonpharmacological approach to reduce hospitalized paediatric burn patients' distress. Future studies with better research designs and validated outcome measures should confirm our findings. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

Mixed conifer forest mortality and establishment before and after prescribed fire in Sequoia National Park, California

USGS Publications Warehouse

Mutch, L.S.; Parsons, D.J.

1998-01-01

Pre-and post-burn tree mortality rates, size structure, basal area, and ingrowth were determined for four 1.0 ha mixed conifer forest stands in the Log Creek and Tharp's Creek watersheds of Sequoia National Park. Mean annual mortality between 1986 and 1990 was 0.8% for both watersheds. In the fall of 1990, the Tharp's Creek watershed was treated with a prescribed burn. Between 1991 and 1995, mean annual mortality was 1.4% in the unburned Log Creek watershed and 17.2% in the burned Tharp's Creek watershed. A drought from 1987 to 1992 likely contributed to the mortality increase in the Log Creek watershed. The high mortality in the Tharp's Creek watershed was primarily related to crown scorch from the 1990 fire and was modeled with logistic regression for white fir (Abies concolor [Gord. and Glend.]) and sugar pine (Pinus lambertiana [Dougl.]). From 1989 to 1994, basal area declined an average of 5% per year in the burned Tharp's Creek watershed, compared to average annual increases of less than 1% per year in the unburned Log Creek watershed and in the Tharp's watershed prior to burning. Post-burn size structure was dramatically changed in the Tharp's Creek stands: 75% of trees ???50 cm and 25% of trees >50 cm were killed by the fire.

Burns at KCMC: epidemiology, presentation, management and treatment outcome.

PubMed

Ringo, Y; Chilonga, K

2014-08-01

About 90% of the global burden of burns occurs in the low and middle income countries. In Africa it is estimated that between 17,000 and 30,000 children under five die each year due to burns. In Tanzania there are no specialized burn centers. Burn patients are often managed in the general surgical wards in most hospitals. Kilimanjaro Christian Medical Centre is one of the four tertiary referral hospitals in Tanzania. This study aimed to review the epidemiology presentation management and outcome of burn patients in this challenging environment. A cross-sectional prospective study involving 41 patients was undertaken from October 2011 to April 2012. 65.9% were males. The largest age group was below 5 years (36.6%). 19.5% were epileptic. More than half of the burns were due to open flame. 80.5% had second degree burns. 56.1% had a BSA of 15% or less and 56.1% had an APACHE score of 10 or less. It was found that 73.2% of burns occurred at home. The commonest prehospital first aid applied was honey. Only 41.5% arrived in hospital within the first 24h after burn. Among the 14.6% who had skin grafting, none had early excision of burn wound. 53.7% developed wound sepsis while 24.4% developed contractures. The mortality rate was 26.8%. Children under five are the worst affected by burns. Most patients had second degree burn wounds. Inappropriate management of the burn wound started just after injury and continued even in hospital. Mortality and complication rates are high. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

77 FR 18297 - Air Traffic Noise, Fuel Burn, and Emissions Modeling Using the Aviation Environmental Design Tool...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-27

... Integrated Routing System-- NIRS].'' The FAA developed the AEDT 2a to model aircraft noise, fuel burn, and... operations schedule. These data are used to compute aircraft noise, fuel burn and emissions simultaneously... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Air Traffic Noise, Fuel Burn, and...

Suicidal behavior by burns among women in two bordering provinces in Iran

PubMed Central

Alaghehbandan, R.; Dinn, N.A.; Rastegar Lari, E.; Rastegar Lari, A.

2015-01-01

Summary The objective of the study was to describe epidemiologic features of suicidal behavior by burns among women in two bordering provinces in Iran. A prospective hospital-based study of all suicidal behaviors by burns among women was carried out in the Iranian provinces of Khorasan (which borders Afghanistan) and Ilam (which borders Iraq) in 2006. These two provinces suffered from war and economic instability with high rates of poverty and unemployment. Data were obtained from patients, family members, and/or significant others through interviews during the course of hospitalization. Of 181 hospitalized patients, 130 (71.8%) were female, representing a hospital separation rate of 5.4 per 100,000 person-year (P-Y). The rate of suicidal behavior involving burns among the rural population was higher than that in the urban population (6.3 vs. 4.7 per 100,000 P-Y, P = 0.09). The median age of the patients was 23 years old, with a mean (±SD) of 27.9 (±14.3) years old. Approximately 68.5% of women were married. Quarrels with “a family member, spouse, a relative, or a friend” (marital plus other conflicts) was identified as the most common precipitating factor (88.5%) in attempting suicide. More than one third of women were abused (physically and/or verbally) by family members (i.e. spouse, father-in-law). Case fatality rate in this study was 52.3% (68/130). Suicide by burns is still a socio-epidemiological problem in Iran, particularly among young, married women in rural areas. Social and economic conditions, as well as violence against women, play a major role in the high rate of suicide by burns. The findings of this study highlight the need for the implementation of a well-organized approach to reduce the rate of suicide by burns among the most vulnerable populations in Iran. PMID:27252614

Resistance of the boreal forest to high burn rates.

PubMed

Héon, Jessie; Arseneault, Dominique; Parisien, Marc-André

2014-09-23

Boreal ecosystems and their large carbon stocks are strongly shaped by extensive wildfires. Coupling climate projections with records of area burned during the last 3 decades across the North American boreal zone suggests that area burned will increase by 30-500% by the end of the 21st century, with a cascading effect on ecosystem dynamics and on the boreal carbon balance. Fire size and the frequency of large-fire years are both expected to increase. However, how fire size and time since previous fire will influence future burn rates is poorly understood, mostly because of incomplete records of past fire overlaps. Here, we reconstruct the length of overlapping fires along a 190-km-long transect during the last 200 y in one of the most fire-prone boreal regions of North America to document how fire size and time since previous fire will influence future fire recurrence. We provide direct field evidence that extreme burn rates can be sustained by a few occasional droughts triggering immense fires. However, we also show that the most fire-prone areas of the North American boreal forest are resistant to high burn rates because of overabundant young forest stands, thereby creating a fuel-mediated negative feedback on fire activity. These findings will help refine projections of fire effect on boreal ecosystems and their large carbon stocks.

Resistance of the boreal forest to high burn rates

PubMed Central

Héon, Jessie; Arseneault, Dominique; Parisien, Marc-André

2014-01-01

Boreal ecosystems and their large carbon stocks are strongly shaped by extensive wildfires. Coupling climate projections with records of area burned during the last 3 decades across the North American boreal zone suggests that area burned will increase by 30–500% by the end of the 21st century, with a cascading effect on ecosystem dynamics and on the boreal carbon balance. Fire size and the frequency of large-fire years are both expected to increase. However, how fire size and time since previous fire will influence future burn rates is poorly understood, mostly because of incomplete records of past fire overlaps. Here, we reconstruct the length of overlapping fires along a 190-km-long transect during the last 200 y in one of the most fire-prone boreal regions of North America to document how fire size and time since previous fire will influence future fire recurrence. We provide direct field evidence that extreme burn rates can be sustained by a few occasional droughts triggering immense fires. However, we also show that the most fire-prone areas of the North American boreal forest are resistant to high burn rates because of overabundant young forest stands, thereby creating a fuel-mediated negative feedback on fire activity. These findings will help refine projections of fire effect on boreal ecosystems and their large carbon stocks. PMID:25201981

Microbiology and antibiotic resistance in severe burns patients: A 5 year review in an adult burns unit.

PubMed

Bahemia, I A; Muganza, A; Moore, R; Sahid, F; Menezes, C N

2015-11-01

Infections are a major problem in burns patients. Knowledge of the incidence and antimicrobial sensitivities of the microorganisms commonly encountered within each institution's burns unit is important as it informs and directs empiric antibiotic therapy. This was a retrospective review of patients admitted from 1 January 2008 to 31 December 2012 to an adult burns intensive care unit. Specimens chosen for analysis were wound swabs, blood cultures, venous catheter tips, tracheal aspirates, sputum, urine and wound tissue. Records were accessed from the admission register and laboratory information system to obtain the relevant data. During the study period, 352 patients were admitted to the adult burns intensive care unit, of which, 341 patients were included. The mortality rate was 44.6%. Flame burns were the commonest. Mortality rate amongst patients with bacteremia was 46.9%. Acinetobacter baumannii, Pseudomonas aeruginosa and methicillin resistant Staphylococcus aureus (MRSA) were found to be the most common organisms cultured in most specimens. The main three organisms identified in specimen cultures in our adult burns intensive care unit were A. baumannii, P. aeruginosa and MRSA. This study has helped establish a better empiric approach to the management of our septic burns patients. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

The risk of burn injury during long-term oxygen therapy: a 17-year longitudinal national study in Sweden

PubMed Central

Tanash, Hanan A; Huss, Fredrik; Ekström, Magnus

2015-01-01

Background Long-term oxygen therapy (LTOT) improves the survival time in hypoxemic chronic obstructive pulmonary disease. Despite warnings about potential dangers, a considerable number of patients continue to smoke while on LTOT. The incidence of burn injuries related to LTOT is unknown. The aim of this study was to estimate the rate of burn injury requiring health care contact during LTOT. Methods Prospective, population-based, consecutive cohort study of people starting LTOT from any cause between January 1, 1992 and December 31, 2009 in the Swedish National Register of Respiratory Failure (Swedevox). Results In total, 12,497 patients (53% women) were included. The mean (standard deviation) age was 72±9 years. The main reasons for starting LTOT were chronic obstructive pulmonary disease (75%) and pulmonary fibrosis (15%). Only 269 (2%) were active smokers when LTOT was initiated. The median follow-up time to event was 1.5 years (interquartile range, 0.55–3.1). In total, 17 patients had a diagnosed burn injury during 27,890 person-years of LTOT. The rate of burn injury was 61 (95% confidence interval, 36–98) per 100,000 person-years. There was no statistically significant difference in the rate of burn injury between ever-smokers and never-smokers, or between men and women. Conclusion The rate of burn injuries in patients on LTOT seems to be low in Sweden. The strict requirements in Sweden for smoking cessation before LTOT initiation may contribute to this finding. PMID:26622175

Overweight and obesity: overrepresentation in the pediatric reconstructive burn population.

PubMed

Mayes, Theresa; Gottschlich, Michele M; Allgeier, Chris; Khoury, Jane; Kagan, Richard J

2010-01-01

Pediatric burn patients are predisposed to excessive weight gain in the reconstructive period, but the cause is unclear. An overweight (OW) or obese (OB) condition is associated with numerous health risks, decreased physical function, and increased morbidity. The purpose of this study was to compare the frequency of OW status in reconstructive, pediatric burn patients with the prevalence in the US population. The authors reviewed the records of 1533 pediatric patients, >1 year from acute burn, admitted for an elective reconstructive procedure. Body mass index between 85th and 95th percentile, according to the National Center for Health Statistics for 2000 growth charts, was classified as OW, and body mass index >95th percentile was classified as OB. Frequency of OW and OB and racial disparity was calculated as a percentage of total patients and compared with pediatric data from National Health and Nutrition Examination Survey for 1999 to 2006, a nationally representative sample. The rate of OW and OB was 16.3 and 24.1%, respectively, in the authors' pediatric burn population. White patients had OW and OB rates of 15.9 and 23.6%, respectively, compared with 18.2 and 30.2%, respectively, in black patients. All OW and OB rates were outside the 95% confidence interval of the nationally representative National Health and Nutrition Examination Survey population. The rates of OW and OB in pediatric reconstructive burn patients exceed the US population standard across age and race stratifications. The prevention and treatment of excessive weight gain should be a component of rehabilitation in pediatric burns.

AFIRM-Wake Forest/University of Pittsburgh Consortium

DTIC Science & Technology

2012-07-01

therapy for infected burn wounds using Lactobacillu s was applied to a new m ouse model and is capable of rescuing the anim al from burn wound induced... Lactobacillus to reduce scar from burn wound infection. We have tested bacteriotherapy with Lactobacillus in a rabbit model of Pseudomonas-infected burn...probiotic therapy with Lactobacillus is sufficient to attenuate the length and severity of a Pseudo monal infection of the burn wound, and that this

Topical Modulation of the Burn Wound Inflammatory Response to Improve Short and Long Term Outcomes

DTIC Science & Technology

2017-10-01

casualty, treatment, organ failure, systemic inflammatory response syndrome , thermal injury, wound model, intervention 3. ACCOMPLISHMENTS:   What...thickness burns have a blister response. Using human eye or H&E studies, we did not observe any blisters in the pig model. However, the OCT...the deeper the partial thickness burn, the bigger the blister, until it gets close to full-thickness burns. The full-thickness burns are dry and

Burn Control in Fusion Reactors via Isotopic Fuel Tailoring

NASA Astrophysics Data System (ADS)

Boyer, Mark D.; Schuster, Eugenio

2011-10-01

The control of plasma density and temperature are among the most fundamental problems in fusion reactors and will be critical to the success of burning plasma experiments like ITER. Economic and technological constraints may require future commercial reactors to operate with low temperature, high-density plasma, for which the burn condition may be unstable. An active control system will be essential for stabilizing such operating points. In this work, a volume-averaged transport model for the energy and the densities of deuterium and tritium fuel ions, as well as the alpha particles, is used to synthesize a nonlinear feedback controller for stabilizing the burn condition. The controller makes use of ITER's planned isotopic fueling capability and controls the densities of these ions separately. The ability to modulate the DT fuel mix is exploited in order to reduce the fusion power during thermal excursions without the need for impurity injection. By moving the isotopic mix in the plasma away from the optimal 50:50 mix, the reaction rate is slowed and the alpha-particle heating is reduced to desired levels. Supported by the NSF CAREER award program (ECCS-0645086).

In vitro burn model illustrating heat conduction patterns using compressed thermal papers.

PubMed

Lee, Jun Yong; Jung, Sung-No; Kwon, Ho

2015-01-01

To date, heat conduction from heat sources to tissue has been estimated by complex mathematical modeling. In the present study, we developed an intuitive in vitro skin burn model that illustrates heat conduction patterns inside the skin. This was composed of tightly compressed thermal papers with compression frames. Heat flow through the model left a trace by changing the color of thermal papers. These were digitized and three-dimensionally reconstituted to reproduce the heat conduction patterns in the skin. For standardization, we validated K91HG-CE thermal paper using a printout test and bivariate correlation analysis. We measured the papers' physical properties and calculated the estimated depth of heat conduction using Fourier's equation. Through contact burns of 5, 10, 15, 20, and 30 seconds on porcine skin and our burn model using a heated brass comb, and comparing the burn wound and heat conduction trace, we validated our model. The heat conduction pattern correlation analysis (intraclass correlation coefficient: 0.846, p < 0.001) and the heat conduction depth correlation analysis (intraclass correlation coefficient: 0.93, p < 0.001) showed statistically significant high correlations between the porcine burn wound and our model. Our model showed good correlation with porcine skin burn injury and replicated its heat conduction patterns. © 2014 by the Wound Healing Society.

Dynamic leaching studies of 48 MWd/kgU UO2 commercial spent nuclear fuel under oxic conditions

NASA Astrophysics Data System (ADS)

Serrano-Purroy, D.; Casas, I.; González-Robles, E.; Glatz, J. P.; Wegen, D. H.; Clarens, F.; Giménez, J.; de Pablo, J.; Martínez-Esparza, A.

2013-03-01

The leaching of a high-burn-up spent nuclear fuel (48 MWd/KgU) has been studied in a carbonate-containing solution and under oxic conditions using a Continuously Stirred Tank Flow-Through Reactor (CSTR). Two samples of the fuel, one prepared from the centre of the pellet (labelled CORE) and another one from the fuel pellet periphery, enriched with the so-called High Burn-Up Structure (HBS, labelled OUT) have been used.For uranium and actinides, the results showed that U, Np, Am and Cm gave very similar normalized dissolution rates, while Pu showed slower dissolution rates for both samples. In addition, dissolution rates were consistently two to four times lower for OUT sample compared to CORE sample.Considering the fission products release the main results are that Y, Tc, La and Nd dissolved very similar to uranium; while Cs, Sr, Mo and Rb have up to 10 times higher dissolution rates. Rh, Ru and Zr seemed to have lower dissolution rates than uranium. The lowest dissolution rates were found for OUT sample.Three different contributions were detected on uranium release, modelled and attributed to oxidation layer, fines and matrix release.

Single Droplet Combustion of Decane in Microgravity: Experiments and Numerical Modeling

NASA Technical Reports Server (NTRS)

Dietrich, D. L.; Struk, P. M.; Ikegam, M.; Xu, G.

2004-01-01

This paper presents experimental data on single droplet combustion of decane in microgravity and compares the results to a numerical model. The primary independent experiment variables are the ambient pressure and oxygen mole fraction, pressure, droplet size (over a relatively small range) and ignition energy. The droplet history (D(sup 2) history) is non-linear with the burning rate constant increasing throughout the test. The average burning rate constant, consistent with classical theory, increased with increasing ambient oxygen mole fraction and was nearly independent of pressure, initial droplet size and ignition energy. The flame typically increased in size initially, and then decreased in size, in response to the shrinking droplet. The flame standoff increased linearly for the majority of the droplet lifetime. The flame surrounding the droplet extinguished at a finite droplet size at lower ambient pressures and an oxygen mole fraction of 0.15. The extinction droplet size increased with decreasing pressure. The model is transient and assumes spherical symmetry, constant thermo-physical properties (specific heat, thermal conductivity and species Lewis number) and single step chemistry. The model includes gas-phase radiative loss and a spherically symmetric, transient liquid phase. The model accurately predicts the droplet and flame histories of the experiments. Good agreement requires that the ignition in the experiment be reasonably approximated in the model and that the model accurately predict the pre-ignition vaporization of the droplet. The model does not accurately predict the dependence of extinction droplet diameter on pressure, a result of the simplified chemistry in the model. The transient flame behavior suggests the potential importance of fuel vapor accumulation. The model results, however, show that the fractional mass consumption rate of fuel in the flame relative to fuel vaporized is close to 1.0 for all but the lowest ambient oxygen mole fractions.

MESOSCALE MODELING OF DEFLAGRATION-INDUCED DECONSOLIDATION IN POLYMER-BONDED EXPLOSIVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, H K; Glascoe, E A; Reaugh, J E

Initially undamaged polymer-bonded explosives can transition from conductive burning to more violent convective burning via rapid deconsolidation at higher pressures. The pressure-dependent infiltration of cracks and pores, i.e., damage, by product gases at the burn-front is a key step in the transition to convective burning. However, the relative influence of pre-existing damage and the evolution of deflagration-induced damage during the transition to convective burning is not well understood. The objective of this study is to investigate the role of microstructure and initial pressurization on deconsolidation. We performed simulations using the multi-physics hydrocode, ALE3D. HMX-Viton A served as our model explosive.more » A Prout-Tompkins chemical kinetic model, Vielle's Law pressure-dependent burning, Gruneisen equation-of-state, and simplified strength model were used for the HMX. The propensity for deconsolidation increased with increasing defect size and decreasing initial pressurization, as measured by the increase in burning surface area. These studies are important because they enable the development of continuum-scale damage models and the design of inherently safer explosives.« less

Theory-Based Cartographic Risk Model Development and Application for Home Fire Safety.

PubMed

Furmanek, Stephen; Lehna, Carlee; Hanchette, Carol

There is a gap in the use of predictive risk models to identify areas at risk for home fires and burn injury. The purpose of this study was to describe the creation, validation, and application of such a model using a sample from an intervention study with parents of newborns in Jefferson County, KY, as an example. Performed was a literature search to identify risk factors for home fires and burn injury in the target population. Obtained from the American Community Survey at the census tract level and synthesized to create a predictive cartographic risk model was risk factor data. Model validation was performed through correlation, regression, and Moran's I with fire incidence data from open records. Independent samples t-tests were used to examine the model in relation to geocoded participant addresses. Participant risk level for fire rate was determined and proximity to fire station service areas and hospitals. The model showed high and severe risk clustering in the northwest section of the county. Strongly correlated with fire rate was modeled risk; the best predictive model for fire risk contained home value (low), race (black), and non high school graduates. Applying the model to the intervention sample, the majority of participants were at lower risk and mostly within service areas closest to a fire department and hospital. Cartographic risk models were useful in identifying areas at risk and analyzing participant risk level. The methods outlined in this study are generalizable to other public health issues.

Modeling prescribed burning experiments and assessing the fire impacts on local to regional air quality

NASA Astrophysics Data System (ADS)

Zhou, L.; Baker, K. R.; Napelenok, S. L.; Elleman, R. A.; Urbanski, S. P.

2016-12-01

Biomass burning, including wildfires and prescribed burns, strongly impact the global carbon cycle and are of increasing concern due to the potential impacts on ambient air quality. This modelling study focuses on the evolution of carbonaceous compounds during a prescribed burning experiment and assesses the impacts of burning on local to regional air quality. The Community Multiscale Air Quality (CMAQ) model is used to conduct 4 and 2 km grid resolution simulations of prescribed burning experiments in southeast Washington state and western Idaho state in summer 2013. The ground and airborne measurements from the field experiment are used to evaluate the model performance in capturing surface and aloft impacts from the burning events. Phase partitioning of organic compounds in the plume are studied as it is a crucial step towards understanding the fate of carbonaceous compounds. The sensitivities of ambient concentrations and deposition to emissions are conducted for organic carbon, elemental carbon and ozone to estimate the impacts of fire on air quality.

A prospective study of time to healing and hypertrophic scarring in paediatric burns: every day counts.

PubMed

Chipp, Elizabeth; Charles, Lisa; Thomas, Clare; Whiting, Kate; Moiemen, Naiem; Wilson, Yvonne

2017-01-01

It is commonly accepted that burns taking longer than 3 weeks to heal have a much higher rate of hypertrophic scarring than those which heal more quickly. However, some of our patients develop hypertrophic scars despite healing within this 3-week period. We performed a prospective study of 383 paediatric burns treated non-operatively at a regional burns centre over a 2-year period from May 2011 to April 2013. Scar assessment was performed by a senior burns therapist using the Vancouver Scar Scale. Overall rates of hypertrophic scarring were 17.2%. Time to healing was the strongest predictor of developing hypertrophic scarring, and the earliest hypertrophic scar developed in a patient who was healed after 8 days. The risk of hypertrophic scarring was multiplied by 1.138 for every additional day taken for the burn wound to heal. There was a trend towards higher rates of hypertrophic scarring in non-white skin types but this did not reach statistical significance. The risk of hypertrophic scarring increases with every day and, therefore, every effort should be made to get the wound healed as quickly as possible, even within the traditional 3-week period usually allowed for healing. We believe that the traditional dogma of aiming for healing within 3 weeks is overly simplistic and should be abandoned: in paediatric burns, every day counts. Not applicable.

Behavior of Explosives Under Pressure in a Diamond Anvil Cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foltz, M F

2006-06-20

Diamond anvil cell (DAC) studies can yield information about the pressure dependence of materials and reactions under conditions comparable to shock loading. The pressure gradient across the face of the diamonds is often deliberately minimized to create uniform pressure over much of the sample and a simplified data set. To reach very high pressures (30-40 GPa), however, it may be necessary to use ''softer'', high nitrogen content diamonds that are more susceptible to bending under pressure. The resulting enhanced pressure gradient then provides a view of high-pressure behavior under anisotropic conditions similar to those found at the burn front inmore » a bulk sample. We discuss visual observations of pressure-induced changes relative to variations in burn rate of several explosives (Triaminotrinitrobenzene, Nitromethane, CL-20) in the DAC. The burn rate behavior of both Nitromethane (NM) and Triaminotrinitrobenzene (TATB) were previously reported for pressures up to {approx}40 GPa. Nitromethane showed a near monotonic increase in burn rate to a maximum at {approx}30 GPa after which the burn rate decreased, all without color change. At higher pressures, the TATB samples had shiny (metallic) polycrystalline zones or inclusions where the pressure was highest in the sample. Around the shiny zones was a gradation of color (red to yellow) that appeared to follow the pressure gradient. The color changes are believed related to disturbances in the resonance structure of this explosive as the intermolecular separations decrease with pressure. The color and type of residue found in unvented gaskets after the burn was complete also varied with pressure. The four polymorphs of CL-20 ({alpha}, {beta}, {gamma}, {var_epsilon}-Hexanitrohexaazaisowurtzitane, HNIW) did not change color up to the highest pressure applied ({approx}30 GPa), and each polymorph demonstrated a distinctly different burn rate signature. One polymorph {beta} was so sensitive to laser ignition over a narrow pressure range that the sample could not be aligned with a low power laser without ignition. The burn rate for that one polymorph could only be measured at pressures above and below that unique pressure. This anomalous ignition threshold is discussed with respect to the matrix of possible polymorphs, most of which have not been isolated in the laboratory. The changes in behavior, color and reaction rates of all samples are discussed with respect to possible implications to chemistry at high pressure.« less

Postdischarge Cause-of-Death Analysis of Combat-Related Burn Patients

PubMed Central

Escolas, Sandra M.; Orman, Jean A.; Chung, Kevin K.; Renz, Evan M.

2017-01-01

Combat operations in Iraq and Afghanistan have resulted in up to 8.8% of combat-related casualties suffering burns. From World War I through Desert Storm, burns have been associated with approximately 4% of the combat-related deaths. Experiencing a blast injury and exposure to killing and death while deployed has been shown to increase suicide risk. Although several studies of military populations have investigated risk factors for death among burn patients during the acute phase, no studies have reported mortality rates, cause-of-death, or the prevalence of suicide after hospital discharge. This study examined the case fatality rate, causes of death, and the prevalence of suicide among 830 combat burn patients discharged from the sole burn center in the U.S. Department of Defense, between March 7, 2003 and March 6, 2013. Cause-of-death was determined through the Armed Forces Medical Examiner’s Office and the Office of the Secretary of Defense’s National Death Index. A total of 11 deaths occurred among the 830 burn survivors, for an overall case fatality rate of 1.3%. Of the 11 who died, five deaths were related to accidental poisoning by exposure to drugs; three were related to operations of war (two after returning to the war zone), and the remaining three died from other accidental causes (one explosion and two vehicle crashes). There was no indication of suicide or suspicion of suicide as a cause-of-death for the former patients included in this study, suggesting that combat burn injury did not appear to increase the risk of death by suicide in our study population. Further research is needed to understand the factors that contribute to the apparent resilience of combat burn survivors. PMID:26629656

Fire spread in chaparral -"go or no-go?"

Treesearch

D.R. Weise; Xiangyang Zhou; Lulu Sun; Shankar Mahalingam

2005-01-01

Current fire models are designed to model the spread of a linear fire front in dead, small-diameter fuels. Fires in predominantly living vegetation account for a large proportion of annual burned area nationally. Prescribed burning is used to manage living fuels; however, prescribed burning is currently conducted under conditions that result in marginal burning. We do...

The impact of socio-economic deprivation on burn injury: A nine-year retrospective study of 6441 patients.

PubMed

Marsden, N J; Battle, C E; Combellack, E J; Sabra, A; Morris, K; Dickson, W A; Whitaker, I S; Evans, P A

2016-03-01

Low socio-economic status is thought to be associated with increased burn risk, however the significance and generalisability across different populations and cultures has been questioned. A nine-year retrospective study of burn presentations to a large teaching hospital (2005-2014) was performed to investigate the association between socio-economic status and burns. Demographic and injury data was collected via the trust 'Information portal'. The Welsh Index of Multiple: Deprivation 2011 was used to score for socio-economic status. Chi-squared test and Odds Ratios were calculated and statistical significance defined as p<0.05 throughout. 6441 burns were identified, with 755 (11.7%) admitted. Overall incidence rates were the highest published in the UK (0.35/1000/year) with sub group analysis showing the highest rates in under fives and males. Significant relationships between both age and burn mechanism and gender and burn mechanism (p=0.0005) were identified. Scald (67.1%) was the most common mechanism with the upper limb (48%) most commonly burned. Chi square analysis demonstrated a significant relationship between socio-economic deprivation, age and burn incidence (p≤0.0005), with a disproportionately high number of burns in patients under the age of 16 in the most deprived quintile (OR 1.23; 95% CI 1.06-1.44). This study specifically highlights patients under the age of 16 living in poorer socio-economic areas as the most at risk of suffering burns receiving hospital attention. This study demonstrates burns as a significant public health issue, and the results should aid in designing specific burn prevention strategies to target high-risk groups. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Determining the Uncertainties in Prescribed Burn Emissions Through Comparison of Satellite Estimates to Ground-based Estimates and Air Quality Model Evaluations in Southeastern US

NASA Astrophysics Data System (ADS)

Odman, M. T.; Hu, Y.; Russell, A. G.

2016-12-01

Prescribed burning is practiced throughout the US, and most widely in the Southeast, for the purpose of maintaining and improving the ecosystem, and reducing the wildfire risk. However, prescribed burn emissions contribute significantly to the of trace gas and particulate matter loads in the atmosphere. In places where air quality is already stressed by other anthropogenic emissions, prescribed burns can lead to major health and environmental problems. Air quality modeling efforts are under way to assess the impacts of prescribed burn emissions. Operational forecasts of the impacts are also emerging for use in dynamic management of air quality as well as the burns. Unfortunately, large uncertainties exist in the process of estimating prescribed burn emissions and these uncertainties limit the accuracy of the burn impact predictions. Prescribed burn emissions are estimated by using either ground-based information or satellite observations. When there is sufficient local information about the burn area, the types of fuels, their consumption amounts, and the progression of the fire, ground-based estimates are more accurate. In the absence of such information satellites remain as the only reliable source for emission estimation. To determine the level of uncertainty in prescribed burn emissions, we compared estimates derived from a burn permit database and other ground-based information to the estimates by the Biomass Burning Emissions Product derived from a constellation of NOAA and NASA satellites. Using these emissions estimates we conducted simulations with the Community Multiscale Air Quality (CMAQ) model and predicted trace gas and particulate matter concentrations throughout the Southeast for two consecutive burn seasons (2015 and 2016). In this presentation, we will compare model predicted concentrations to measurements at monitoring stations and evaluate if the differences are commensurate with our emission uncertainty estimates. We will also investigate if spatial and temporal patterns in the differences reveal the sources of the uncertainty in the prescribed burn emission estimates.

Treatments for Common Psychiatric Conditions Among Children and Adolescents During Acute Rehabilitation and Reintegration Phases of Burn Injury

PubMed Central

Arceneaux, Lisa L.; Meyer, Walter J.

2016-01-01

Advances in critical care and surgical management during the last 20 years have decreased mortality rates among children with severe burn injuries. This improved survival rate has prompted researchers to study the psychological aspects of recovering from a burn injury. Initially, research focused primarily on epidemiology, prevention and descriptions of the psychological phenomenon experienced by the children and adolescents. Whereas, previously, interventions were often utilized during the acute phases of burn injury without knowledge of the long-term effects, more recently, priorities have shifted to include long-term treatment outcome studies. The purpose of this paper is to review and discuss the current evidenced-based techniques and their efficacy in the treatment of common psychological and psychiatric conditions among children and adolescents during the 3 major phases of burn injury. PMID:19919208

Improving Diagnosis of Sepsis After Burn Injury Using a Portable Sepsis Alert System

DTIC Science & Technology

vital signs of heart rate variability, regional tissue oxygenation, and noninvasive cardiac output can diagnose burn sepsis earlier, reducing...morbidity and mortality. Rationale: Heart Rate Variability (HRV), regional Tissue Oxygenation, and non-invasive Cardiac Output (CO), have shown promise in

Factors affecting nest survival of Henslow's Sparrows (Ammodramus henslowii) in southern Indiana

USGS Publications Warehouse

Crimmins, Shawn M.; McKann, Patrick C.; Robb, Joseph R.; Lewis, Jason P.; Vanosdol, Teresa; Walker, Benjamin A.; Williams, Perry J.; Thogmartin, Wayne E.

2016-01-01

Populations of Henslow’s Sparrows have declined dramatically in recent decades, coinciding with widespread loss of native grassland habitat. Prescribed burning is a primary tool for maintaining grassland patches, but its effects on nest survival of Henslow’s Sparrows remains largely unknown, especially in conjunction with other factors. We monitored 135 nests of Henslow’s Sparrows at Big Oaks National Wildlife Refuge in southern Indiana from 1998–2001 in an effort to understand factors influencing nest survival, including prescribed burning of habitat. We used a mixed-effects implementation of the logistic exposure model to predict daily nest survival in an information theoretic framework. We found that daily survival declined near the onset of hatching and increased with the height of standing dead vegetation, although this relationship was weak. We found only nominal support to suggest that time since burn influenced nest survival. Overall, nest age was the most important factor in estimating daily nest survival rates. Our daily survival estimate from our marginal model (0.937) was similar to that derived from the Mayfield method (0.944) suggesting that our results are comparable to previous studies using the Mayfield approach. Our results indicate that frequent burning to limit woody encroachment into grassland habitats might benefit Henslow’s Sparrow, but that a variety of factors ultimately influence daily nest survival. However, we note that burning too frequently can also limit occupancy by Henslow’s Sparrows. We suggest that additional research is needed to determine the population-level consequences of habitat alteration and if other extrinsic factors influence demographics of Henslow’s Sparrows.

Computer Program Applications to Tactical Missile Conceptual Design.

DTIC Science & Technology

1981-06-01

initialized at a potential maximum of 1.25 inches/second (Ref. 21 and is allowed to decrease to arrive at a compati- ble burn area and web thickness...the same restrictions. The burn rate starts at 0.45 inches/sec- ond (Ref. 21 and is decreased to provide an acceptable web thickness and burn area. The...0.45 inches/sec- ond to provide a proper web thickness. "THE.SUSTAINER MOTOR HAS AN END BURNING GRAIN." The required burn area for the sustainer was

Experimental and theoretical study of diesel soot reactivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marcuccilli, F; Gilot, P.; Stanmore, B.

1994-12-31

In order to provide data for modelling the performance of a regenerative soot filter, a study of the oxidation kinetics of diesel soot in the temperature range from 600 C to 800 C was undertaken. Isothermal burning rates at a number of temperatures were measured in rectangular soot beds within a thermobalance. The technique was easy to use, but the combustion rate was found to depend on bed mass. The oxidation process was thus limited by mass transfer effects. A two-dimensional mathematical model of oxygen transfer was developed to extract the true kinetic rates from experimental data. The two-dimensional approachmore » was required because significant oxygen depletion occurred along both axes. Using assumed kinetic rates, oxygen concentration profiles in the gas phase above the bed and within the bed were calculated. The true kinetics at a number of temperatures were, then established by matching predicted oxygen consumption with measured consumption. Application of the model required values of the effective diffusion coefficient for oxygen within the bed. Accordingly, the structure and properties of the soot aggregates were determined. A supplements study was carried out to identify the appropriate primary reaction products. The measured kinetic rates were then used in a simpler, monodimensional model to evaluate the mean oxygen mass transfer coefficients to the surface of the bed. The results show that burning below about 730 C is in regime 1 and can be described by K = 6.9 {times} 10{sup 12} exp ({minus}207,000/RT) (s{sup {minus}1}) with R = 8.314 J/mol {times} K. Above, 730 C, there is a decrease in apparent activation energy, probably due to thermal ``annealing,`` which changes the microstructure of the carbon. As a result, the inherent reactivity declines and/or the bed becomes less accessible to oxygen.« less

Therapeutic efficacy of an antibiotic-loaded nanosheet in a murine burn-wound infection model.

PubMed

Saito, Akihiro; Miyazaki, Hiromi; Fujie, Toshinori; Ohtsubo, Shinya; Kinoshita, Manabu; Saitoh, Daizoh; Takeoka, Shinji

2012-08-01

Polymeric ultra-thin films (nanosheets) possess unique properties that make them suitable materials for various biomedical applications. In our previous study, we assessed the use of an antibiotic (tetracycline, TC)-loaded nanosheet (or "TC-nanosheet") for the treatment of gastrointestinal tissue defects. The nanosheet consisted of three functional layers: layer-by-layer nanosheet as a stable platform, TC as an antimicrobial agent with autofluorescence for tracing, and a poly(vinyl acetate) nanosheet to act as a protecting layer. The TC-nanosheet has high flexibility, adhesive strength and transparency. Here, we evaluated the effectiveness of the TC-nanosheet in preventing full thickness burn-wound infections. In an in vivo study, murine dorsal skin was injured by full-thickness burns and then infected with Pseudomonas aeruginosa (P. aeruginosa), a common bacterium causing burn-associated infections. The wound site was treated either with a TC-nanosheet, TC-unloaded nanosheet or left untreated. Wound management was facilitated by the high transparency of the TC-nanosheet. The TC-nanosheet significantly improved burn-wound infection by P. aeruginosa in mice. Indeed, all mice treated with the TC-nanosheet survived, whereas the other treatment groups displayed increased rates of mortality due to bacterial infection. According to histological analyses and viable bacterial counting in the liver (bacterial translocation), the TC-nanosheets were able to prevent not only the local inflammation but also systemic inflammation. We conclude that the TC-nanosheet can act as an effective treatment for full-thickness burn-wound infection. Hence, the TC-nanosheet is a promising therapeutic tool for burn-wound management in severely burn-injured patients. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Exposures and reported symptoms associated with occupational deployment to the Buncefield fuel depot fire, England 2005.

PubMed

Morgan, O; Verlander, N Q; Kennedy, F; Moore, M; Birch, S; Kearney, J; Lewthwaite, P; Lewis, R; O'Brian, S; Osman, J; Reacher, M

2008-06-01

An explosion at the Buncefield fuel depot outside London occurred on 11 December 2005. We conducted a retrospective cohort study of airborne exposures and health status for workers deployed. Deployed individuals were identified through their occupational health departments. We sent a self-completion questionnaire asking about health symptoms during the burn and post-burn phases. The prevalence of health symptoms in workers was compared to symptoms in local residents not under the smoke plume. Of 1949 eligible individuals, 815 returned questionnaires (response rate 44%). Respiratory protection was used by 39%. Symptoms were reported by 41% of individuals during the burn phase compared with 26% in the post-burn phase. In a final multivariable model, reporting of any symptoms was associated with deployment inside the inner fire cordon during the burn phase (OR 2.07, 95% CI 1.24 to 3.47) and wearing a face mask (OR 2.33, 95% CI 1.67 to 3.26). Compared with the general public, eye irritation (prevalence ratio (PR) 2.1, 95% CI 1.5 to 3.0), coughing (PR 1.3, 95% CI 1.0 to 1.8) and headaches (PR 1.7, 95% CI 1.2 to 2.5) were more common in workers deployed during the burn phase but not the post-burn phase. Increased reporting of symptoms close to the fire during the burn phase was consistent with increased exposure to products of combustion, although no major acute illness was reported. That only a minority of individuals used face masks, which were not protective for symptoms, raises questions about the availability of adequate respiratory protection for such incidents.

Survival function and protein malnutrition in burns patients at a rural hospital in Africa.

PubMed

Kingu, H J; Longo-Mbenza, Benjamin; Dhaffala, A; Mazwai, E L

2011-07-01

The aim of this study was to estimate the incidence of acute malnutrition and to identify predictors of case fatality among burn patients in the poorest South African province, Eastern Cape. This longitudinal follow-up study was conducted among consecutive burn patients admitted to Nelson Mandela Academic Hospital, Mthatha, South Africa, between 2006 and 2008. Patients were monitored and treated daily from admission to discharge. Outcomes were acute protein malnutrition and mortality. Patients' demography, total body surface area (TBSA) of the burn, cause of the burn, weight, height, location of the burn, hemoglobin, serum albumin, wound infection, and antibiotics after culture and sensitivity results were the potential predictors of in-hospital mortality. A Cox's proportional hazards model for the time to death was then used to identify independent predictors of mortality after adjusting for confounding factors. Kaplan-Meier survival curves were generated for each arm of exposure status. In all, 67 patients (35 males, 59 children) were studied. The mean (range) age was 8±12 years (1 month to 59 years). The cumulative incidence of acute malnutrition was 62.0% (n=42): 46.3% (n=31) at admission and 15.7% (n=11) after 7 days of hospitalization. Incidence of mortality was 16.4% (n=11 with in-hospital acute malnutrition). The only significant and independent predictors of mortality were total body surface area (TBSA) burn>40% [hazard ratio (HR) 10.5, 95% confidence interval (CI) 1.7-63; P<0.01] and affected anterior trunk (HR 4.4, 95% CI 1.3-14.7; P=0.018). Urgent prevention strategies of burns and evidence-based practice with early nutritional supplementation are needed to reduce high rates of malnutrition and mortality.

Risk factors for the development of heterotopic ossification in seriously burned adults: A National Institute on Disability, Independent Living and Rehabilitation Research burn model system database analysis.

PubMed

Levi, Benjamin; Jayakumar, Prakash; Giladi, Avi; Jupiter, Jesse B; Ring, David C; Kowalske, Karen; Gibran, Nicole S; Herndon, David; Schneider, Jeffrey C; Ryan, Colleen M

2015-11-01

Heterotopic ossification (HO) is a debilitating complication of burn injury; however, incidence and risk factors are poorly understood. In this study, we use a multicenter database of adults with burn injuries to identify and analyze clinical factors that predict HO formation. Data from six high-volume burn centers, in the Burn Injury Model System Database, were analyzed. Univariate logistic regression models were used for model selection. Cluster-adjusted multivariate logistic regression was then used to evaluate the relationship between clinical and demographic data and the development of HO. Of 2,979 patients in the database with information on HO that addressed risk factors for development of HO, 98 (3.5%) developed HO. Of these 98 patients, 97 had arm burns, and 96 had arm grafts. When controlling for age and sex in a multivariate model, patients with greater than 30% total body surface area burn had 11.5 times higher odds of developing HO (p < 0.001), and those with arm burns that required skin grafting had 96.4 times higher odds of developing HO (p = 0.04). For each additional time a patient went to the operating room, odds of HO increased by 30% (odds ratio, 1.32; p < 0.001), and each additional ventilator day increased odds by 3.5% (odds ratio, 1.035; p < 0.001). Joint contracture, inhalation injury, and bone exposure did not significantly increase odds of HO. Risk factors for HO development include greater than 30% total body surface area burn, arm burns, arm grafts, ventilator days, and number of trips to the operating room. Future studies can use these results to identify highest-risk patients to guide deployment of prophylactic and experimental treatments. Prognostic study, level III.

Risk Factors for the Development of Heterotopic Ossification in Seriously Burned Adults: A NIDRR Burn Model System Database Analysis

PubMed Central

Levi, Benjamin; Jayakumar, Prakash; Giladi, Avi; Jupiter, Jesse B.; Ring, David C.; Kowalske, Karen; Gibran, Nicole S.; Herndon, David; Schneider, Jeffrey C.; Ryan, Colleen M.

2015-01-01

Purpose Heterotopic ossification (HO) is a debilitating complication of burn injury; however, incidence and risk factors are poorly understood. In this study we utilize a multicenter database of adults with burn injuries to identify and analyze clinical factors that predict HO formation. Methods Data from 6 high-volume burn centers, in the Burn Injury Model System Database, were analyzed. Univariate logistic regression models were used for model selection. Cluster-adjusted multivariate logistic regression was then used to evaluate the relationship between clinical and demographic data and the development of HO. Results Of 2,979 patients in the database with information on HO that addressed risk factors for development of HO, 98 (3.5%) developed HO. Of these 98 patients, 97 had arm burns, and 96 had arm grafts. Controlling for age and sex in a multivariate model, patients with >30% total body surface area (TBSA) burn had 11.5x higher odds of developing HO (p<0.001), and those with arm burns that required skin grafting had 96.4x higher odds of developing HO (p=0.04). For each additional time a patient went to the operating room, odds of HO increased 30% (OR 1.32, p<0.001), and each additional ventilator day increase odds 3.5% (OR 1.035, p<0.001). Joint contracture, inhalation injury, and bone exposure did not significantly increase odds of HO. Conclusion Risk factors for HO development include >30% TBSA burn, arm burns, arm grafts, ventilator days, and number of trips to the operating room. Future studies can use these results to identify highest-risk patients to guide deployment of prophylactic and experimental treatments. PMID:26496115

Predictors of muscle protein synthesis after severe pediatric burns

USDA-ARS?s Scientific Manuscript database

Objectives: Following a major burn, muscle protein synthesis rate increases but in most patients, this response is not sufficient to compensate the also elevated protein breakdown. Given the long-term nature of the pathophysiologic response to burn injury, we hypothesized that skeletal muscle prot...

Sensitivity of global terrestrial carbon cycle dynamics to variability in satellite-observed burned area

NASA Astrophysics Data System (ADS)

Poulter, Benjamin; Cadule, Patricia; Cheiney, Audrey; Ciais, Philippe; Hodson, Elke; Peylin, Philippe; Plummer, Stephen; Spessa, Allan; Saatchi, Sassan; Yue, Chao; Zimmermann, Niklaus E.

2015-02-01

Fire plays an important role in terrestrial ecosystems by regulating biogeochemistry, biogeography, and energy budgets, yet despite the importance of fire as an integral ecosystem process, significant advances remain to improve its prognostic representation in carbon cycle models. To recommend and to help prioritize model improvements, this study investigates the sensitivity of a coupled global biogeography and biogeochemistry model, LPJ, to observed burned area measured by three independent satellite-derived products, GFED v3.1, L3JRC, and GlobCarbon. Model variables are compared with benchmarks that include pantropical aboveground biomass, global tree cover, and CO2 and CO trace gas concentrations. Depending on prescribed burned area product, global aboveground carbon stocks varied by 300 Pg C, and woody cover ranged from 50 to 73 Mkm2. Tree cover and biomass were both reduced linearly with increasing burned area, i.e., at regional scales, a 10% reduction in tree cover per 1000 km2, and 0.04-to-0.40 Mg C reduction per 1000 km2. In boreal regions, satellite burned area improved simulated tree cover and biomass distributions, but in savanna regions, model-data correlations decreased. Global net biome production was relatively insensitive to burned area, and the long-term land carbon sink was robust, 2.5 Pg C yr-1, suggesting that feedbacks from ecosystem respiration compensated for reductions in fuel consumption via fire. CO2 transport provided further evidence that heterotrophic respiration compensated any emission reductions in the absence of fire, with minor differences in modeled CO2 fluxes among burned area products. CO was a more sensitive indicator for evaluating fire emissions, with MODIS-GFED burned area producing CO concentrations largely in agreement with independent observations in high latitudes. This study illustrates how ensembles of burned area data sets can be used to diagnose model structures and parameters for further improvement and also highlights the importance in considering uncertainties and variability in observed burned area data products for model applications.

Implementation and outcomes of an evidence-based precepting program for burn nurses.

PubMed

Robbins, Johnnie R; Valdez-Delgado, Krystal K; Caldwell, Nicole W; Yoder, Linda H; Hayes, Elizabeth J; Barba, Michaèl G; Greeley, Hope L; Mitchell, Colleen; Mann-Salinas, Elizabeth A

2017-11-01

There is significant nationwide interest in transitioning new and new-to-specialty nurses into practice, especially in burn care. Lack of a structured transition program in our Burn Center was recognized as a contributing factor for nursing dissatisfaction and increased turnover compared to other hospital units. Employee evaluations exposed a need for more didactic instruction, hands-on learning, and preceptor support. The goal of this project was to implement an evidence-based transition to practice program specific to the burn specialty. The Iowa Model of Evidence-based Practice served as the model for this project. A working group was formed consisting of nurse scientists, clinical nurse leaders, clinical nurse specialists, lead preceptors, staff nurse preceptors and wound care coordinators. A systematic review of the literature was conducted focusing on nurse transition; preceptor development and transitioning nurse training programs with competency assessment, ongoing multifaceted evaluation and retention strategies were created. The evidence-based Vermont Nurses in Partnership (VNIP) Clinical Transition Framework was selected and subsequent education was provided to all Burn Center leaders and staff. Benchmarks for basic knowledge assessment (BKAT) and burn wound care were established among current staff by work site and education level to help evaluate transitioning nurses. Policies were modified to count each preceptor/transitioning nurse dyad as half an employee on the schedule. Multiple high-fidelity simulation scenarios were created to expand hands-on opportunities. From September 2012-December 2013, 110 (57% acute care nursing) Burn Center staff attended the VNIP Clinical Coaching Course, to include 34 interdisciplinary staff (rehabilitation, education, respiratory therapy, and outpatient clinic staff) and 100% of identified preceptors (n=33). A total of 30 new nurses participated in the transition program: 26 (87%) completed, 3 (10%) did not complete, and 1 (3%) received exception (no patient care). Transitioning nurses achieved passing BKAT scores (n=22; 76%) and WC scores (n=24; 93%); individual remediation was provided for those failing to achieve unit benchmarks and transition training was modified to improve areas of weakness. Transitioning nurses' weekly competency progression average initial ratings on a 10 point scale (10 most competent) were 5±2; final ratings averaged 9±1 (n=25) (p<0.0001). An evidence-based team practice approach toward preceptorship created a standardized, comprehensive and flexible precepting program to assist and support transition to specialty burn practice for experienced nurses. Use of objective metrics enabled ongoing assessment and made training adaptable, individualized, and cost effective. Application of this standardized approach across our organization may improve consistency for all transitions in practice specialty. Copyright © 2017. Published by Elsevier Ltd.

High-Fidelity Microstructural Characterization and Performance Modeling of Aluminized Composite Propellant

DOE PAGES

Kosiba, Graham D.; Wixom, Ryan R.; Oehlschlaeger, Matthew A.

2017-10-27

Image processing and stereological techniques were used to characterize the heterogeneity of composite propellant and inform a predictive burn rate model. Composite propellant samples made up of ammonium perchlorate (AP), hydroxyl-terminated polybutadiene (HTPB), and aluminum (Al) were faced with an ion mill and imaged with a scanning electron microscope (SEM) and x-ray tomography (micro-CT). Properties of both the bulk and individual components of the composite propellant were determined from a variety of image processing tools. An algebraic model, based on the improved Beckstead-Derr-Price model developed by Cohen and Strand, was used to predict the steady-state burning of the aluminized compositemore » propellant. In the presented model the presence of aluminum particles within the propellant was introduced. The thermal effects of aluminum particles are accounted for at the solid-gas propellant surface interface and aluminum combustion is considered in the gas phase using a single global reaction. In conclusion, properties derived from image processing were used directly as model inputs, leading to a sample-specific predictive combustion model.« less

High-Fidelity Microstructural Characterization and Performance Modeling of Aluminized Composite Propellant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kosiba, Graham D.; Wixom, Ryan R.; Oehlschlaeger, Matthew A.

Image processing and stereological techniques were used to characterize the heterogeneity of composite propellant and inform a predictive burn rate model. Composite propellant samples made up of ammonium perchlorate (AP), hydroxyl-terminated polybutadiene (HTPB), and aluminum (Al) were faced with an ion mill and imaged with a scanning electron microscope (SEM) and x-ray tomography (micro-CT). Properties of both the bulk and individual components of the composite propellant were determined from a variety of image processing tools. An algebraic model, based on the improved Beckstead-Derr-Price model developed by Cohen and Strand, was used to predict the steady-state burning of the aluminized compositemore » propellant. In the presented model the presence of aluminum particles within the propellant was introduced. The thermal effects of aluminum particles are accounted for at the solid-gas propellant surface interface and aluminum combustion is considered in the gas phase using a single global reaction. In conclusion, properties derived from image processing were used directly as model inputs, leading to a sample-specific predictive combustion model.« less

The Synthesis of 44Ti and 56Ni in Massive Stars

NASA Astrophysics Data System (ADS)

Chieffi, Alessandro; Limongi, Marco

2017-02-01

We discuss the influence of rotation on the combined synthesis of {}44{Ti} and {}56{Ni} in massive stars. While {}56{Ni} is significantly produced by both complete and incomplete explosive Si burning, {}44{Ti} is mainly produced by complete explosive Si burning, with a minor contribution (in standard non-rotating models) from incomplete explosive Si burning and O burning (both explosive and hydrostatic). We find that, in most cases, the thickness of the region exposed to incomplete explosive Si burning increases in rotating models (initial velocity, v ini = 300 km s-1) and since {}56{Ni} is significantly produced in this zone, the fraction of mass coming from the complete explosive Si burning zone necessary to get the required amount of {}56{Ni} reduces. Therefore the amount of {}44{Ti} ejected for a given fixed amount of {}56{Ni} decreases in rotating models. However, some rotating models at [Fe/H] = -1 develop a very extended O convective shell in which a consistent amount of {}44{Ti} is formed, preserved, and ejected in the interstellar medium. Hence a better modeling of the thermal instabilities (convection) in the advanced burning phases together with a critical analysis of the cross sections of the nuclear reactions operating in O burning are relevant for the understanding of the synthesis of {}44{Ti}.

The importance of illumination in a non-contact photoplethysmography imaging system for burn wound assessment

NASA Astrophysics Data System (ADS)

Mo, Weirong; Mohan, Rachit; Li, Weizhi; Zhang, Xu; Sellke, Eric W.; Fan, Wensheng; DiMaio, J. Michael; Thatcher, Jeffery E.

2015-02-01

We present a non-contact, reflective photoplethysmogram (PPG) imaging method and a prototype system for identifying the presence of dermal burn wounds during a burn debridement surgery. This system aims to provide assistance to clinicians and surgeons in the process of dermal wound management and wound triage decisions. We examined the system variables of illumination uniformity and intensity and present our findings. An LED array, a tungsten light source, and eventually high-power LED emitters were studied as illumination methods for our PPG imaging device. These three different illumination sources were tested in a controlled tissue phantom model and an animal burn model. We found that the low heat and even illumination pattern using high power LED emitters provided a substantial improvement to the collected PPG signal in our animal burn model. These improvements allow the PPG signal from different pixels to be comparable in both time-domain and frequency-domain, simplify the illumination subsystem complexity, and remove the necessity of using high dynamic range cameras. Through the burn model output comparison, such as the blood volume in animal burn data and controlled tissue phantom model, our optical improvements have led to more clinically applicable images to aid in burn assessment.

A Burke-Schumann Analysis of Dual-Flame Structure Supported by a Burning Droplet

NASA Technical Reports Server (NTRS)

Nayagam, V.; Dietrich, D.; Williams, F. A.

2016-01-01

Droplet combustion experiments carried out onboard the International Space Station (ISS), using pure fuels and fuel mixtures, have shown that quasi-steady burning can be sustained by a non-traditional flame configuration, namely a "cool flame" burning in the "partial-burning" regime where both fuel and oxygen leak through the low-temperature controlled flame-sheet. Recent experiments involving large, bi-component fuel (n-decane and hexanol, 50/50 by volume) droplets at elevated pressures show that the visible, hot flame becomes extremely weak while the burning rate remains relatively high, suggesting the possibility of simultaneous presence of "cool" and "hot" flames of roughly equal importance. The radiant output from these bi-component droplets is relatively high and cannot be accounted for only by the presence of a visible hot-flame. In this analysis we explore the theoretical possibility of a dual-flame structure, where one flame lies close to the droplet surface called the "cool-flame," and other farther away from the droplet surface, termed the "hot-flame." A Burke-Schumann analysis of this dual-structure seems to indicate such flame structures are possible over a narrow range of initial conditions. Theoretical results can be compared against available experimental data for pure and bi-component fuel droplet combustion to test how realistic the model may be.

Understanding the Environmental and Climate Impacts of Biomass Burning in Northern Sub-Saharan Africa

NASA Technical Reports Server (NTRS)

Ichoku, Charles; Gatebe, Charles; Bolten, John; Policelli, Fritz; Habib, Shahid; Lee, Jejung; Wang, Jun; Wilcox, Eric; Adegoke, Jimmy

2011-01-01

The northern sub-Saharan African (NSSA) region, bounded on the north and south by the Sahara and the Equator, respectively, and stretching from the West to the East African coastlines, has one of the highest biomass-burning rates per unit land area among all regions of the world. Because of the high concentration and frequency of fires in this region, with the associated abundance of heat release and gaseous and particulate smoke emissions, biomass-burning activity is believed to be one of the drivers of the regional carbon and energy cycles, with serious implications for the water cycle. A new interdisciplinary research effort sponsored by NASA is presently being focused on the NSSA region, to better understand the possible connection between the intense biomass burning observed from satellite year after year across the region and the rapid depletion of the regional water resources, as exemplified by the dramatic drying of Lake Chad. A combination of remote sensing and modeling approaches is being utilized in investigating multiple regional surface, atmospheric, and water-cycle processes, and inferring possible links between them. In this presentation, we will discuss preliminary results as well as the path toward improved understanding'of the interrelationships and feedbacks between the biomass burning and the environmental change dynamics in the NSSA region.

Interactions and Feedbacks Between Biomass Burning and Water Cycle Dynamics Across the Northern Sub-Saharan African Region

NASA Technical Reports Server (NTRS)

Ichoku, Charles

2012-01-01

The northern sub-Saharan African (NSSA) region, bounded on the north and south by the Sahara and the Equator, respectively, and stretching from the West to the East African coastlines, has one of the highest biomass-burning rates per unit land area among all regions of the world. Because of the high concentration and frequency of fires in this region, with the associated abundance of heat release and gaseous and particulate smoke emissions, biomass-burning activity is believed to be one of the drivers of the regional carbon and energy cycles, with serious implications for the water cycle. A new interdisciplinary research effort sponsored by NASA is presently being focused on the NSSA region, to better understand the possible connection between the intense biomass burning observed from satellite year after year across the region and the rapid depletion of the regional water resources, as exemplified by the dramatic drying of Lake Chad. A combination of remote sensing and modeling approaches is being utilized in investigating multiple regional surface, atmospheric, and water-cycle processes, and inferring possible links between them. In this presentation, we will discuss preliminary results as well as the path toward improved understanding of the interrelationships and feedbacks between the biomass burning and the environmental change dynamics in the NSSA region.

Benchmarking Outcomes in the Critically Injured Burn Patient

PubMed Central

Klein, Matthew B.; Goverman, Jeremy; Hayden, Douglas L.; Fagan, Shawn P.; McDonald-Smith, Grace P.; Alexander, Andrew K.; Gamelli, Richard L.; Gibran, Nicole S.; Finnerty, Celeste C.; Jeschke, Marc G.; Arnoldo, Brett; Wispelwey, Bram; Mindrinos, Michael N.; Xiao, Wenzhong; Honari, Shari E.; Mason, Philip H.; Schoenfeld, David A.; Herndon, David N.; Tompkins, Ronald G.

2014-01-01

Objective To determine and compare outcomes with accepted benchmarks in burn care at six academic burn centers. Background Since the 1960s, U.S. morbidity and mortality rates have declined tremendously for burn patients, likely related to improvements in surgical and critical care treatment. We describe the baseline patient characteristics and well-defined outcomes for major burn injuries. Methods We followed 300 adults and 241 children from 2003–2009 through hospitalization using standard operating procedures developed at study onset. We created an extensive database on patient and injury characteristics, anatomic and physiological derangement, clinical treatment, and outcomes. These data were compared with existing benchmarks in burn care. Results Study patients were critically injured as demonstrated by mean %TBSA (41.2±18.3 for adults and 57.8±18.2 for children) and presence of inhalation injury in 38% of the adults and 54.8% of the children. Mortality in adults was 14.1% for those less than 55 years old and 38.5% for those age ≥55 years. Mortality in patients less than 17 years old was 7.9%. Overall, the multiple organ failure rate was 27%. When controlling for age and %TBSA, presence of inhalation injury was not significant. Conclusions This study provides the current benchmark for major burn patients. Mortality rates, notwithstanding significant % TBSA and presence of inhalation injury, have significantly declined compared to previous benchmarks. Modern day surgical and medically intensive management has markedly improved to the point where we can expect patients less than 55 years old with severe burn injuries and inhalation injury to survive these devastating conditions. PMID:24722222

Accounting for Mass Transfer Kinetics when Modeling the Impact of Low Permeability Layers in a Groundwater Source Zone on Dissolved Contaminant Fate and Transport

DTIC Science & Technology

2014-03-27

Clay Interface) ...................................................................................................... 40 Figure 9: Time-Dependent...vs Constant Dissolution Rate BTCs (Monitoring Well in Clay ...pits, poured down sanitary sewer systems, and partially burned in fire training pits. Poor handling and disposal of chlorinated solvents have

Size-dependent validation of MODIS MCD64A1 burned area over six vegetation types in boreal Eurasia: Large underestimation in croplands

NASA Astrophysics Data System (ADS)

Zhu, C.; Kobayashi, H.; Kanaya, Y.; Saito, M.

2017-12-01

Pollutants emitted from wildfires in boreal Eurasia can be transported to the Arctic, and their subsequent deposition could accelerate global warming. The Moderate Resolution Imaging Spectroradiometer (MODIS) MCD64A1 burned area product is used widely for global mapping of burned areas in conjunction with products such as the Global Fire Emission Database version 4, which can estimate pollutant emissions. However, uncertainties due to the "moderate resolution" (500 m) characteristic of the MODIS sensor could be introduced. Here, we present a size-dependent validation of MCD64A1 with reference to higher resolution (better than 30 m) satellite products (Landsat 7 ETM+, RapidEye, WorldView-2, and GeoEye-1) for six ecotypes over 12 regions of boreal Eurasia. We considered the 2012 boreal Eurasia burning season when severe wildfires occurred and when Arctic sea ice extent was historically low. Among the six ecotypes, we found MCD64A1 burned areas comprised only 13% of the reference products in croplands because of inadequate detection of small fires (<100 ha). Our results indicate that over all ecotypes, the actual burned area in boreal Eurasia (15,256 km2) could have been 16% greater than suggested by MCD64A1 (13,187 km2). We suggest applying correction factors of 0.5-8.2 when using emission rates based on MCD64A1 burned areas in chemistry and climate models of the studied regions. This implies the effects of wildfire emissions in boreal Eurasia on Arctic warming could be greater than currently estimated.

A model of ponderosa pine growth response to prescribed burning

Treesearch

Elaine Kennedy Sutherland; W. Wallace Covington; Steve Andariese

1991-01-01

Our objective was to model the radial growth response of individual ponderosa pines to prescribed burning in northern Arizona. We sampled 188 trees from two study areas, which were burned in 1976. Within each study area, control and burned trees were of similar age, vigor, height, and competition index. At Chimney Spring, trees were older, less vigorous, and taller and...

Combustion of Metals in Carbon Dioxide and Reduced-Gravity Environments

NASA Technical Reports Server (NTRS)

Branch, M. C.; Abbud-Madrid, A.; Modak, A.; Dreyer, C. B.; Daily, J. W.

2001-01-01

Ongoing exploration and future mission2001110444 s to Mars have given impetus to research on the use of natural resources of the planet. Since carbon dioxide (CO2) constitutes approximately 95% of the Mars atmosphere and since it reacts directly and vigorously with several metals, this investigation focuses on metal-CO2 reactions as a possible combination for rocket-propellant production and energy generation. Magnesium (Mg) has been initially selected as the metal fuel owing to its low ignition temperature and high specific impulse and burning rate in CO2. Our studies in this field started with low gravity (g) combustion tests of Mg in O2, CO2, and CO. Reduced gravity provided a clear picture of the burning phenomena by eliminating the intrusive buoyant flows in high-temperature metal reactions and by removing the destructive effect of gravity on the shape of molten metal samples. Suspended cylindrical metal samples of 2, 3, and 4-mm in diameter and length were radiatively ignited in low-g to generate free-floating samples exhibiting a spherically symmetric flame with increasing metal-oxide accumulation in an outer shell. For the Mg-CO2 combination, burning times twice as long as in normal-g and five times longer than in Mg-O2 flames were observed, revealing a diffusion-controlled reaction. The burning time is proportional to the square of the sample diameter. In tests conducted with pure CO, combustion was not possible without constant heating of the sample due to the formation of a thick carbon-containing coating around the Mg sample generated by surface reactions. The following work presents two new studies that attempt to explain some of the low-g experimental observations. First, a simplified one-dimensional, quasi-steady numerical model is developed to obtain temperature, species concentrations, and burning rates of the spherically symmetric diffusion flame around the Mg sample burning in O2 and CO2. Second, a Planar Laser Induced Fluorescence (PLIF) technique is implemented to provide spatially resolved measurements of magnesium oxide (MgO) in the reaction zone of Mg samples burning in O2 and CO2. These experiments reveal fundamental differences between the two combustion systems.

Biomass Burning

Atmospheric Science Data Center

2015-07-27

Projects:  Biomass Burning Definition/Description:  Biomass Burning: This data set represents the geographical and temporal distribution of total amount of biomass burned. These data may be used in general circulation models (GCMs) and ...

A mobile app for measuring the surface area of a burn in three dimensions: comparison to the Lund and Browder assessment.

PubMed

Goldberg, Harry; Klaff, Justin; Spjut, Aaron; Milner, Stephen

2014-01-01

The aim of this study was to compare the ease and accuracy of measuring the surface area of a severe burn through the use of a mobile software application (BurnMed) to the traditional method of assessment, the Lund and Browder chart. BurnMed calculates the surface area of a burn by enabling the user to first manipulate a three-dimensional model on a mobile device and then by touching the model at the locations representing the patient's injury. The surface area of the burn is calculated in real time. Using a cohort of 18 first-year medical students with no experience in burn care, the surface area of a simulated burn on a mannequin was made using BurnMed and compared to estimates derived from the Lund and Browder chart. At the completion of this study, students were asked to complete a questionnaire designed to assess the ease of use of BurnMed. Users were able to easily and accurately measure the surface area of a simulated burn using the BurnMed application. In addition, there was less variability in surface area measurements with the application compared to the results obtained using the Lund and Browder chart. Users also reported that BurnMed was easier to use than the Lund and Browder chart. A software application, BurnMed, has been developed for a mobile device that easily and accurately determines the surface area of a burn. This system uses a three-dimensional model that can be rotated, enlarged, and transposed by the health care provider to easily determine the extent of a burn. Results show that the variability of measurements using BurnMed is lower than the measurements obtained using the Lund and Browder chart. BurnMed is available at no charge in the Apple™ Store.

Evidence based management for paediatric burn: new approaches and improved scar outcomes.

PubMed

Kishikova, Lyudmila; Smith, Matthew D; Cubison, Tania C S

2014-12-01

Little evidence has been produced on the best practice for managing paediatric burns. We set out to develop a formal approach based on the finding that hypertrophic scarring is related to healing-time, with durations under 21 days associated with improved scar outcome. Incorporating new advances in burn care, we compared outcomes under the new approach to a cohort treated previously. Our study was a retrospective cross-sectional case note study, with demographic, treatment and outcome information collected. The management and outcome of each case was assessed and compared against another paediatric burns cohort from 2006. 181 burns presenting across a six month period were analysed (2010 cohort) and compared to 337 children from a previous cohort from 2006. Comparison of patients between cohorts showed an overall shift towards shorter healing-times in the 2010 cohort. A lower overall rate of hypertrophic scarring was seen in the 2010 cohort, and for corresponding healing-times after injury, hypertrophic scarring rates were halved in comparison to the 2006 cohort. We demonstrate that the use of a structured approach for paediatric burns has improved outcomes with regards to healing-time and hypertrophic scarring rate. This approach allows maximisation of healing potential and implements aggressive prophylactic measures. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

MSFR TRU-burning potential and comparison with an SFR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiorina, C.; Cammi, A.; Franceschini, F.

2013-07-01

The objective of this work is to evaluate the Molten Salt Fast Reactor (MSFR) potential benefits in terms of transuranics (TRU) burning through a comparative analysis with a sodium-cooled FR. The comparison is based on TRU- and MA-burning rates, as well as on the in-core evolution of radiotoxicity and decay heat. Solubility issues limit the TRU-burning rate to 1/3 that achievable in traditional low-CR FRs (low-Conversion-Ratio Fast Reactors). The softer spectrum also determines notable radiotoxicity and decay heat of the equilibrium actinide inventory. On the other hand, the liquid fuel suggests the possibility of using a Pu-free feed composed onlymore » of Th and MA (Minor Actinides), thus maximizing the MA burning rate. This is generally not possible in traditional low-CR FRs due to safety deterioration and decay heat of reprocessed fuel. In addition, the high specific power and the lack of out-of-core cooling times foster a quick transition toward equilibrium, which improves the MSFR capability to burn an initial fissile loading, and makes the MSFR a promising system for a quick (i.e., in a reactor lifetime) transition from the current U-based fuel cycle to a novel closed Th cycle. (authors)« less

Soil respiration and root biomass responses to burning in calabrian pine (Pinus brutia) stands in Edirne, Turkey.

PubMed

Tufekcioglu, Aydin; Kucuk, Mehmet; Bilmis, Tuncay; Altun, Lokman; Yilmaz, Murat

2010-01-01

In this study soil properties and root biomass responses to prescribed fire were investigated in 25-30 year-old calabrian pine (Pinus brutia Ten.) stands in Edirne, Turkey. The stands were established by planting and were subjected to prescribed burning in July 2005. Soil respiration rates were determined every two months using the soda-lime method over a two-year period. Fine (> or = 2 mm diameter) and small root (> 2-5 mm diameter) biomass were sampled approximately bimonthly using the sequential coring method. Soil respiration rates in burned sites were significantly higher than in control sites during the summer season but there was no significant difference in the other seasons. Soil respiration rates were correlated significantly with soil moisture and soil temperature. Fine and small root biomass were significantly lower in burned sites than in control sites. Mean fine root biomass values were 3204 kg ha(-1) for burned and 3772 kg ha(-1) for control sites. Annual soil CO2 releases totaled 515 g Cm(-2) for burned and 418 g C m(-2) for control sites. Our results indicate that, depending on site conditions, fire could be used successfully as a tool in the management of calabrian pine stands in the study area.

Integrating satellite imagery with simulation modeling to improve burn severity mapping

Treesearch

Eva C. Karau; Pamela G. Sikkink; Robert E. Keane; Gregory K. Dillon

2014-01-01

Both satellite imagery and spatial fire effects models are valuable tools for generating burn severity maps that are useful to fire scientists and resource managers. The purpose of this study was to test a new mapping approach that integrates imagery and modeling to create more accurate burn severity maps. We developed and assessed a statistical model that combines the...

Sustained high incidence of injuries from burns in a densely populated urban slum in Kenya: an emerging public health priority.

PubMed

Wong, Joshua M; Nyachieo, Dhillon O; Benzekri, Noelle A; Cosmas, Leonard; Ondari, Daniel; Yekta, Shahla; Montgomery, Joel M; Williamson, John M; Breiman, Robert F

2014-09-01

Ninety-five percent of burn deaths occur in low- and middle-income countries (LMICs); however, longitudinal household-level studies have not been done in urban slum settings, where overcrowding and unsafe cook stoves may increase likelihood of injury. Using a prospective, population-based disease surveillance system in the urban slum of Kibera in Kenya, we examined the incidence of household-level burns of all severities from 2006-2011. Of approximately 28,500 enrolled individuals (6000 households), we identified 3072 burns. The overall incidence was 27.9/1000 person-years-of-observation. Children <5 years old sustained burns at 3.8-fold greater rate compared to (p<0.001) those ≥5 years old. Females ≥5 years old sustained burns at a rate that was 1.35-fold (p<0.001) greater than males within the same age distribution. Hospitalizations were uncommon (0.65% of all burns). The incidence of burns, 10-fold greater than in most published reports from Africa and Asia, suggests that such injuries may contribute more significantly than previously thought to morbidity in LMICs, and may be increased by urbanization. As migration from rural areas into urban slums rapidly increases in many African countries, characterizing and addressing the rising burden of burns is likely to become a public health priority. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Relationship between Slivering Point and Gas Generation Rules of 19-Perforation TEGDN Propellants with Different Length/Outside Diameter Ratios and Perforation Diameters

NASA Astrophysics Data System (ADS)

Xiao, Zhenggang; Xu, Fuming

2018-04-01

In order to investigate the relationship between the slivering point and burning progressivity, a set of 19-perforation propellants containing triethylene glycol dinitrate (TEGDN) with different lengths/outside diameter ratios and perforation diameters was prepared and tested in a closed vessel. The mass fraction of burnt propellant was derived from the recorded pressure-time history of 19-perforation TEGDN propellants in the closed vessel according to the gas state equation and the form function of tested propellants. Based on the form function calculation and the mass fraction of burnt propellant, instantaneous burning surface area and the burning rate were obtained. The influence of length/outside diameter ratios and perforation diameters on the progressive combustion performance is studied through the dynamic vivacity method. With an increase in the length/outsider diameter, the slivering point occurs earlier and the slivering process lasts longer. Further, the burning progressivity of surface area can be improved. For propellants with same length/outside diameter ratio, with a decreasing of perforation diameter, the slivering point lags behind and the burning progressivity becomes greater. The slivering point corresponds to the instantaneous burning area, which is related to the form function and total burning process as well. However, the total burning progressivity of propellant is a very comprehensive result of propellant under multiple actions, including the mass fraction of burnt propellant, grain size and burning rate at different pressure regions. The correlation between them can boost a better understanding on the interaction between grain size, slivering burning process and burning progressivity.

The effect of a honey based gel and silver sulphadiazine on bacterial infections of in vitro burn wounds.

PubMed

Boekema, B K H L; Pool, L; Ulrich, M M W

2013-06-01

Bacterial contamination remains a constant threat in burn wound care. Topical treatments to combat contaminations have good bactericidal effects but can have detrimental effects for the healing process. Treatments with for example silver can increase healing times. Honey based products can be a good alternative as it is antibacterial and patient-friendly. We evaluated the bactericidal and cytotoxic effects of a honey based gel and silver sulphadiazine in a human burn wound model with Pseudomonas aeruginosa. After adding 10(5)colony forming units of P. aeruginosa, topical treatments were applied on the burn wound models. After 2, 12, 24, 28 and 70 h, bacteria were dislodged and counted by plating dilutions. Cytotoxic effects were evaluated histologically in samples of burn wound models treated topically for 3 weeks, without bacteria. L-Mesitran Soft significantly reduced the bacterial load (5-log reduction) up to 24h but did not completely eliminate bacteria from the burn wounds. After Flammazine(®) treatment, only a few colony forming units were observed at all time points. In contrast, re-epithelialization was significantly reduced after application of Flammazine(®) compared to L-Mesitran Soft or control. This in vitro model of burn wound infection can be used to evaluate topical treatments. L-Mesitran Soft is a good alternative for treating burn wounds but the slightly lower bactericidal activity in the burn wound model warrants a higher frequency of application. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

Recent Biomass Burning in the Tropics and Related Changes in Tropospheric Ozone

NASA Technical Reports Server (NTRS)

Ziemke; Chandra, J. R. S.; Duncan, B. N.; Schoeberl, M. R.; Torres, O.; Damon, M. R.; Bhartia, P. K.

2009-01-01

Biomass burning is an important source of chemical precursors of tropospheric ozone. In the tropics, biomass burning produces ozone enhancements over broad regions of Indonesia, Africa, and South America including Brazil. Fires are intentionally set in these regions during the dry season each year to clear cropland and to clear land for human/industrial expansion. In Indonesia enhanced burning occurs during dry El Nino conditions such as in 1997 and 2006. These burning activities cause enhancement in atmospheric particulates and trace gases which are harmful to human health. Measurements from the Aura Ozone Monitoring Instrument (OMI) and Microwave Limb Sounder (MLS) from October 2004-November 2008 are used to evaluate the effects of biomass burning on tropical tropospheric ozone. These measurements show sizeable decreases approx.15-20% in ozone in Brazil during 2008 compared to 2007 which we attribute to the reduction in biomass burning. Three broad biomass burning regions in the tropics (South America including Brazil, western Africa, and Indonesia) were analyzed in the context of OMI/MLS measurements and the Global Modeling Initiative (GMI) chemical transport model developed at Goddard Space Flight Center. The results indicate that the impact of biomass burning on ozone is significant within and near the burning regions with increases of approx.10-25% in tropospheric column ozone relative to average background concentrations. The model suggests that about half of the increases in ozone from these burning events come from altitudes below 3 km. Globally the model indicates increases of approx.4-5% in ozone, approx.7-9% in NO, (NO+NO2), and approx.30-40% in CO.

Modeling Emissions and Vertical Plume Transport of Crop Residue Burning Experiments in the Pacific Northwest

NASA Astrophysics Data System (ADS)

Zhou, L.; Baker, K. R.; Napelenok, S. L.; Pouliot, G.; Elleman, R. A.; ONeill, S. M.; Urbanski, S. P.; Wong, D. C.

2017-12-01

Crop residue burning has long been a common practice in agriculture with the smoke emissions from the burning linked to negative health impacts. A field study in eastern Washington and northern Idaho in August 2013 consisted of multiple burns of well characterized fuels with nearby surface and aerial measurements including trace species concentrations, plume rise height and boundary layer structure. The chemical transport model CMAQ (Community Multiscale Air Quality Model) was used to assess the fire emissions and subsequent vertical plume transport. The study first compared assumptions made by the 2014 National Emission Inventory approach for crop residue burning with the fuel and emissions information obtained from the field study and then investigated the sensitivity of modeled carbon monoxide (CO) and PM2.5 concentrations to these different emission estimates and plume rise treatment with CMAQ. The study suggests that improvements to the current parameterizations are needed in order for CMAQ to reliably reproduce smoke plumes from burning. In addition, there is enough variability in the smoke emissions, stemming from variable field-specific information such as field size, that attempts to model crop residue burning should use field-specific information whenever possible.

The effects of hillslope-scale variability in burn severity on post-fire sediment delivery

NASA Astrophysics Data System (ADS)

Quinn, Dylan; Brooks, Erin; Dobre, Mariana; Lew, Roger; Robichaud, Peter; Elliot, William

2017-04-01

With the increasing frequency of wildfire and the costs associated with managing the burned landscapes, there is an increasing need for decision support tools that can be used to assess the effectiveness of targeted post-fire management strategies. The susceptibility of landscapes to post-fire soil erosion and runoff have been closely linked with the severity of the wildfire. Wildfire severity maps are often spatial complex and largely dependent upon total vegetative biomass, fuel moisture patterns, direction of burn, wind patterns, and other factors. The decision to apply targeted treatment to a specific landscape and the amount of resources dedicated to treating a landscape should ideally be based on the potential for excessive sediment delivery from a particular hillslope. Recent work has suggested that the delivery of sediment to a downstream water body from a hillslope will be highly influenced by the distribution of wildfire severity across a hillslope and that models that do not capture this hillslope scale variability would not provide reliable sediment and runoff predictions. In this project we compare detailed (10 m) grid-based model predictions to lumped and semi-lumped hillslope approaches where hydrologic parameters are fixed based on hillslope scale averaging techniques. We use the watershed scale version of the process-based Watershed Erosion Prediction Projection (WEPP) model and its GIS interface, GeoWEPP, to simulate the fire impacts on runoff and sediment delivery using burn severity maps at a watershed scale. The flowpath option in WEPP allows for the most detail representation of wildfire severity patterns (10 m) but depending upon the size of the watershed, simulations are time consuming and computational demanding. The hillslope version is a simpler approach which assigns wildfire severity based on the severity level that is assigned to the majority of the hillslope area. In the third approach we divided hillslopes in overland flow elements (OFEs) and assigned representative input values on a finer scale within single hillslopes. Each of these approaches were compared for several large wildfires in the mountainous ranges of central Idaho, USA. Simulations indicated that predictions based on lumped hillslope modeling over-predict sediment transport by as much as 4.8x in areas of high to moderate burn severity. Annual sediment yield within the simulated watersheds ranged from 1.7 tonnes/ha to 6.8 tonnes/ha. The disparity between simulated sediment yield with these approaches was attributed to hydrologic connectivity of the burn patterns within the hillslope. High infiltration rates between high severity sites can greatly reduce the delivery of sediment. This research underlines the importance of accurately representing soil burn severity along individual hillslopes in hydrologic models and the need for modeling approaches to capture this variability to reliability simulate soil erosion.

On the Dependence of the X-Ray Burst Rate on Accretion and Spin Rate

NASA Astrophysics Data System (ADS)

Cavecchi, Yuri; Watts, Anna L.; Galloway, Duncan K.

2017-12-01

Nuclear burning and its dependence on the mass accretion rate are fundamental ingredients for describing the complicated observational phenomenology of neutron stars (NSs) in binary systems. Motivated by high-quality burst rate data emerging from large statistical studies, we report general calculations relating the bursting rate to the mass accretion rate and NS rotation frequency. In this first work, we ignore general relativistic effects and accretion topology, although we discuss where their inclusion should play a role. The relations we derive are suitable for different burning regimes and provide a direct link between parameters predicted by theory and what is to be expected in observations. We illustrate this for analytical relations of different unstable burning regimes that operate on the surface of an accreting NS. We also use the observed behavior of the burst rate to suggest new constraints on burning parameters. We are able to provide an explanation for the long-standing problem of the observed decrease of the burst rate with increasing mass accretion that follows naturally from these calculations: when the accretion rate crosses a certain threshold, ignition moves away from its initially preferred site, and this can cause a net reduction of the burst rate due to the effects of local conditions that set local differences in both the burst rate and stabilization criteria. We show under which conditions this can happen even if locally the burst rate keeps increasing with accretion.

Burning mechanism and regression rate of RX-35-AU and RX-35-AV as a function of HMX particle size measured by the hybrid closed bomb-strand burner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao, W.C.; Costantino, M.S.; Ornellas, D.L.

1990-04-01

In this study, the average surface regression rate of two HMX-based cast explosives, RX-35-AU and RX-35-AV, is measured to pressures above 750 MPa using a hybrid closed bomb-strand burner. The hybrid design allows the simultaneous measurement of pressure and regression rate over a large range of pressures in each experiment. Nitroglycerin/Triacetin (75/25) and polyethylene glycol (PEG) are used as the energetic plasticizer and polymeric binder, respectively, in both formulations. The HMX solids loading in each formulation is 50 wt %, consisting of a narrow particle size distribution of 6--8 {mu}m for RX-35-AU and 150--177 {mu}m for RX-35-AV. Of special interestmore » are the regression rate and burning mechanism as a function of the initial particle size distribution and the mechanical properties fo the cast explosives. In general, the regression rate for the larger particle size formulation, RX-35-AV, is two to three times faster compared to that for RX-35-AU. Up to 750 MPa and independent of the initial confinement pressure, RX-35-AU exhibits a planar burning mechanism with the regression rate obeying the classical aP{sup n} formalism. For RX-35-AV, however, the burning behavior is erratic for samples ignited at 200 MPa confinement pressure. At confinement pressures above 400 MPa, the regression exhibits more of a planar burning mechanism. The unstable combustion behavior for RX-35-AV at lower confinement pressures is related to several mechanisms: (1) an abrupt increase in surface area due to particle fracture and subsequent translation and rotation, resulting in debonding and creating porosity, (2) thixotropic'' separation of the binder and nitramine, causing the significantly greater fracture damage to the nitramine during the loading cycle, (3) microscopic damage to the nitramine crystals that increase its intrinsic burning rate. 12 refs., 8 figs., 2 tabs.« less

Modeling crop residue burning experiments to evaluate smoke emissions and plume transport.

PubMed

Zhou, Luxi; Baker, Kirk R; Napelenok, Sergey L; Pouliot, George; Elleman, Robert; O'Neill, Susan M; Urbanski, Shawn P; Wong, David C

2018-06-15

Crop residue burning is a common land management practice that results in emissions of a variety of pollutants with negative health impacts. Modeling systems are used to estimate air quality impacts of crop residue burning to support retrospective regulatory assessments and also for forecasting purposes. Ground and airborne measurements from a recent field experiment in the Pacific Northwest focused on cropland residue burning was used to evaluate model performance in capturing surface and aloft impacts from the burning events. The Community Multiscale Air Quality (CMAQ) model was used to simulate multiple crop residue burns with 2 km grid spacing using field-specific information and also more general assumptions traditionally used to support National Emission Inventory based assessments. Field study specific information, which includes area burned, fuel consumption, and combustion completeness, resulted in increased biomass consumption by 123 tons (60% increase) on average compared to consumption estimated with default methods in the National Emission Inventory (NEI) process. Buoyancy heat flux, a key parameter for model predicted fire plume rise, estimated from fuel loading obtained from field measurements can be 30% to 200% more than when estimated using default field information. The increased buoyancy heat flux resulted in higher plume rise by 30% to 80%. This evaluation indicates that the regulatory air quality modeling system can replicate intensity and transport (horizontal and vertical) features for crop residue burning in this region when region-specific information is used to inform emissions and plume rise calculations. Further, previous vertical emissions allocation treatment of putting all cropland residue burning in the surface layer does not compare well with measured plume structure and these types of burns should be modeled more similarly to prescribed fires such that plume rise is based on an estimate of buoyancy. Copyright © 2018 Elsevier B.V. All rights reserved.

Development of advanced diagnostics for characterization of burning droplets in microgravity

NASA Technical Reports Server (NTRS)

Sankar, Subramanian; Buermann, Dale H.; Bachalo, William D.

1995-01-01

Diagnostic techniques currently used for microgravity research are generally not as advanced as those used in earth based gravity experiments. Diagnostic techniques for measuring the instantaneous radial temperature profile (or temperature gradients) within the burning droplet do not exist. Over the past few years, Aerometrics has been researching and developing a rainbow thermometric technique for measuring the droplet temperatures of burning droplets. This technique has recently been integrated with the phase Doppler interferometric technique to yield a diagnostic instrument that can be used to simultaneously measure the size, velocity, and temperature of burning droplets in complex spray flames. Also, the rainbow thermometric technique has been recently integrated with a point-diffraction interferometric technique for measuring the instantaneous gas phase temperature field surrounding a burning droplet. These research programs, apart from being very successful, have also helped us identify other innovative techniques for the characterization of burning droplets. For example, new techniques have been identified for measuring the instantaneous regression rate of burning droplets. Also, there is the possibility of extracting the instantaneous radial temperature distribution or the temperature gradients within a droplet during transient heating. What is important is that these diagnostic techniques have the potential for making use of inexpensive, light-weight, and rugged devices such as diode lasers and linear CCD arrays. As a result, they can be easily packaged for incorporation into microgravity drop-test and flight-test facilities. Furthermore, with the use of linear CCD arrays, data rates as high as 10-100 kHz can be easily achieved. This data rate is orders of magnitude higher than what is currently achievable. In this research and development program, a compact and rugged diagnostic system will be developed that can be used to measure instantaneous fuel droplet diameter, droplet regression rate, and the droplet internal temperature profiles or gradients at very high data rates in microgravity experiments.

Solid Propellant Test Motor Scaling

DTIC Science & Technology

2001-09-01

50 Figure 40. Comparison of Measured and Calculated Strand and Small Motor Burning Rates for Fundamental Studies of HTPB /AP Smokeless...Propellants...................................... 51 Figure 41. Agreement Between 2x4 Motor and Strand Burning Rate Data for Non-aluminized HTPB /AP...58 Figure 51. Comparison Between Results Obtained with Ultrasonic Method and Standard

Influence of uranium hydride oxidation on uranium metal behaviour

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, N.; Hambley, D.; Clarke, S.A.

2013-07-01

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, ifmore » sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)« less

46 CFR 114.600 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... supplement—Safety Glazing Materials For Glazing Motor Vehicles Operating on Land Highways 116.1030 American... Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position... Burning Characteristics of Building Materials 116.405; 116.422; 116.423 ASTM E 648-97, Standard Test...

Burning of solids in oxygen-rich environments in normal and reduced gravity. [combustion of cellulose acetates

NASA Technical Reports Server (NTRS)

Andracchio, C. R.; Cochran, T. H.

1974-01-01

An experimental program was conducted to investigate the combustion characteristics of solids burning in a weightless environment. The combustion characteristics of thin cellulose acetate material were obtained from specimens burned in supercritical as well as in low pressure oxygen atmospheres. Flame spread rates were measured and found to depend on material thickness and pressure in both normal gravity (1-g) and reduced gravity (0-g). A gravity effect on the burning process was also observed; the ratio of 1-g to 0-g flame spread rate becomes larger with increasing material thickness. Qualitative results on the combustion characteristics of metal screens (stainless steel, Inconel, copper, and aluminum) burning in supercritical oxygen and normal gravity are also presented. Stainless steel (300 sq mesh) was successfully ignited in reduced gravity; no apparent difference in the flame spread pattern was observed between 1-g and 0-g.

Assessment of biomass burning emissions and their impacts on urban and regional PM2.5: a Georgia case study.

PubMed

Tian, Di; Hu, Yongtao; Wang, Yuhang; Boylan, James W; Zheng, Mei; Russell, Armistead G

2009-01-15

Biomass burning is a major and growing contributor to particulate matter with an aerodynamic diameter less than 2.5 microm (PM2.5). Such impacts (especially individual impacts from each burning source) are quantified using the Community Multiscale Air Quality (CMAQ) Model, a chemical transport model (CTM). Given the sensitivity of CTM results to uncertain emission inputs, simulations were conducted using three biomass burning inventories. Shortcomings in the burning emissions were also evaluated by comparing simulations with observations and results from a receptor model. Model performance improved significantly with the updated emissions and speciation profiles based on recent measurements for biomass burning: mean fractional bias is reduced from 22% to 4% for elemental carbon and from 18% to 12% for organic matter; mean fractional error is reduced from 59% to 50% for elemental carbon and from 55% to 49% for organic matter. Quantified impacts of biomass burning on PM2.5 during January, March, May, and July 2002 are 3.0, 5.1, 0.8, and 0.3 microg m(-3) domainwide on average, with more than 80% of such impacts being from primary emissions. Impacts of prescribed burning dominate biomass burning impacts, contributing about 55% and 80% of PM2.5 in January and March, respectively, followed by land clearing and agriculture field burning. Significant impacts of wildfires in May and residential wood combustion in fireplaces and woodstoves in January are also found.

Effect of gabapentin on morphine consumption and pain after surgical debridement of burn wounds: a double-blind randomized clinical trial study.

PubMed

Rimaz, Siamak; Alavi, Cyrus Emir; Sedighinejad, Abbas; Tolouie, Mohammad; Kavoosi, Sharareh; Koochakinejad, Leila

2012-01-01

Burn pain is recognized as being maximal during therapeutic procedures, and wound debridement can be more painful than the burn injury itself. Uncontrolled acute burn pain increases the stress response and the incidence of chronic pain and associated depression. Although opiates are excellent analgesics, they do not effectively prevent central sensitization to pain. The anticonvulsant gabapentin has been proven effective for treating neuropathic pain in large placebo-controlled clinical trials. Experimental and clinical studies have demonstrated antihyperalgesic effects in models with central neuronal sensitization. It has been suggested that central neuronal sensitization may play an important role in postoperative pain. The aim of this study was to investigate the effect of gabapentin on morphine consumption and postoperative pain in burn patients undergoing resection of burn wounds. In a randomized, double-blind, placebo-controlled study, 50 burn patients received a single oral dose of gabapentin (1200mg) or placebo 2h before surgery. Anesthesia was induced with propofol and fentanyl and maintained by infusingpropofol, remifentanil, and 50% N2O in O2. All patients received patient-controlled analgesia with morphine at doses of 2.5 mg bolus and a lock-out time of 10 min for 24h before the operation. Pain was assessed on a visual analog scale (VAS) at rest and during movement at 1,4,8,12,16,20, and 24 h before the operation. Heart rate, oxygen saturation, mean arterial blood pressure, respiratory rate, sedation score, and morphine consumption were studied. All the enrolled patients were able to complete the study; therefore, data from 50 patients wereanalyzed. The VAS scores at rest andduring movement at 1,4,8,12,16,20, and 24 h after the operation were significantly lower in the gabapentin group than in the placebo group (P < 0.05). Morphine consumption was significantly lessr in the gabapentin group than in the placebo group (P < 0.05). Sedation scores were similar in the 2 groups at all measured times. There were no differences in adverse effects between the groups. A single oral dose of 1200mg gabapentin resulted in a substantial reduction in postoperative morphine consumption and pain scores after surgical debridement in burn patients.

Regional changes in charcoal-burning suicide rates in East/Southeast Asia from 1995 to 2011: a time trend analysis.

PubMed

Chang, Shu-Sen; Chen, Ying-Yeh; Yip, Paul S F; Lee, Won Jin; Hagihara, Akihito; Gunnell, David

2014-04-01

Suicides by carbon monoxide poisoning resulting from burning barbecue charcoal reached epidemic levels in Hong Kong and Taiwan within 5 y of the first reported cases in the early 2000s. The objectives of this analysis were to investigate (i) time trends and regional patterns of charcoal-burning suicide throughout East/Southeast Asia during the time period 1995-2011 and (ii) whether any rises in use of this method were associated with increases in overall suicide rates. Sex- and age-specific trends over time were also examined to identify the demographic groups showing the greatest increases in charcoal-burning suicide rates across different countries. We used data on suicides by gases other than domestic gas for Hong Kong, Japan, the Republic of Korea, Taiwan, and Singapore in the years 1995/1996-2011. Similar data for Malaysia, the Philippines, and Thailand were also extracted but were incomplete. Graphical and joinpoint regression analyses were used to examine time trends in suicide, and negative binomial regression analysis to study sex- and age-specific patterns. In 1995/1996, charcoal-burning suicides accounted for <1% of all suicides in all study countries, except in Japan (5%), but they increased to account for 13%, 24%, 10%, 7%, and 5% of all suicides in Hong Kong, Taiwan, Japan, the Republic of Korea, and Singapore, respectively, in 2011. Rises were first seen in Hong Kong after 1998 (95% CI 1997-1999), followed by Singapore in 1999 (95% CI 1998-2001), Taiwan in 2000 (95% CI 1999-2001), Japan in 2002 (95% CI 1999-2003), and the Republic of Korea in 2007 (95% CI 2006-2008). No marked increases were seen in Malaysia, the Philippines, or Thailand. There was some evidence that charcoal-burning suicides were associated with an increase in overall suicide rates in Hong Kong, Taiwan, and Japan (for females), but not in Japan (for males), the Republic of Korea, and Singapore. Rates of change in charcoal-burning suicide rate did not differ by sex/age group in Taiwan and Hong Kong but appeared to be greatest in people aged 15-24 y in Japan and people aged 25-64 y in the Republic of Korea. The lack of specific codes for charcoal-burning suicide in the International Classification of Diseases and variations in coding practice in different countries are potential limitations of this study. Charcoal-burning suicides increased markedly in some East/Southeast Asian countries (Hong Kong, Taiwan, Japan, the Republic of Korea, and Singapore) in the first decade of the 21st century, but such rises were not experienced by all countries in the region. In countries with a rise in charcoal-burning suicide rates, the timing, scale, and sex/age pattern of increases varied by country. Factors underlying these variations require further investigation, but may include differences in culture or in media portrayals of the method. Please see later in the article for the Editors' Summary.

Modeling Candle Flame Behavior In Variable Gravity

NASA Technical Reports Server (NTRS)

Alsairafi, A.; Tien, J. S.; Lee, S. T.; Dietrich, D. L.; Ross, H. D.

2003-01-01

The burning of a candle, as typical non-propagating diffusion flame, has been used by a number of researchers to study the effects of electric fields on flame, spontaneous flame oscillation and flickering phenomena, and flame extinction. In normal gravity, the heat released from combustion creates buoyant convection that draws oxygen into the flame. The strength of the buoyant flow depends on the gravitational level and it is expected that the flame shape, size and candle burning rate will vary with gravity. Experimentally, there exist studies of candle burning in enhanced gravity (i.e. higher than normal earth gravity, g(sub e)), and in microgravity in drop towers and space-based facilities. There are, however, no reported experimental data on candle burning in partial gravity (g < g(sub e)). In a previous numerical model of the candle flame, buoyant forces were neglected. The treatment of momentum equation was simplified using a potential flow approximation. Although the predicted flame characteristics agreed well with the experimental results, the model cannot be extended to cases with buoyant flows. In addition, because of the use of potential flow, no-slip boundary condition is not satisfied on the wick surface. So there is some uncertainty on the accuracy of the predicted flow field. In the present modeling effort, the full Navier-Stokes momentum equations with body force term is included. This enables us to study the effect of gravity on candle flames (with zero gravity as the limiting case). In addition, we consider radiation effects in more detail by solving the radiation transfer equation. In the previous study, flame radiation is treated as a simple loss term in the energy equation. Emphasis of the present model is on the gas-phase processes. Therefore, the detailed heat and mass transfer phenomena inside the porous wick are not treated. Instead, it is assumed that a thin layer of liquid fuel coated the entire wick surface during the burning process. This is the limiting case that the mass transfer process in the wick is much faster than the evaporation process at the wick surface.

Impact of Early Inpatient Rehabilitation on Adult Burn Survivors' Functional Outcomes and Resource Utilization.

PubMed

Gomez, Manuel; Tushinski, Morris; Jeschke, Marc G

On July 2012, a rehabilitation hospital merged with a trauma center where the regional burn center is located. That rehabilitation center provides the only burn rehabilitation program in our region. The objective of this study was to determine if earlier initiation of inpatient rehabilitation after merger had an effect on burn survivors' functional outcomes and resource utilization. A retrospective review of electronic data of burn survivors' functional outcomes (functional independence measure [FIM] ratings on admission, at discharge, and percent change), and resource utilization (waiting time for rehab, burn center length of stay [LOS], rehab LOS, physiotherapy and occupational therapy rehabilitation workload [RehabWorkload], and discharge destination) was undertaken. Adult burn survivors who required inpatient rehabilitation and were transferred from the burn center to the inpatient rehabilitation service before the merger (July 2010-June 2012) were compared with those transferred after the merger (July 2012-June 2014). One hundred thirty-eight burn survivors were transferred from the burn center to the inpatient rehabilitation service during the study period. Sixty (43.5%) were transferred before and 78 (56.5%) were transferred after the merger. There were 97 (70.3%) men and 41 (29.7%) women with a mean age of 47.9 ± 17.9 years. TBSA burn was 24.2 ± 16.9%, and full thickness burn was 13.1 ± 16.4%. The etiology of these burns were flame (72.5%), scald (19.6%), electrical (5.1%), chemical (2.2%), and contact (0.7%). Patients in both groups had similar age, inhalation injury, TBSA, full thickness burn, FIM ratings, RehabWorkload, and burn etiology. Patients transferred before the merger had significantly more chemical burns (5% vs 0%, P = .046), and more work-related burns (26.7% vs 7.7%, P = .004). Patients transferred after the merger had significantly shorter burn center LOS (28.5 ± 20.9 days vs 38.8 ± 34.2 days, P = .043), and shorter waiting time for rehab (0.7 ± 1.1 days vs 1.5 ± 2.3 days, P = .010) than patients transferred before the merger. Early initiation of inpatient rehabilitation, after the burn center and the inpatient rehabilitation service were located in the same hospital, improved burn survivors' resource utilization.

Towards more efficient burn care: Identifying factors associated with good quality of life post-burn.

PubMed

Finlay, V; Phillips, M; Allison, G T; Wood, F M; Ching, D; Wicaksono, D; Plowman, S; Hendrie, D; Edgar, D W

2015-11-01

As minor burn patients constitute the vast majority of a developed nation case-mix, streamlining care for this group can promote efficiency from a service-wide perspective. This study tested the hypothesis that a predictive nomogram model that estimates likelihood of good long-term quality of life (QoL) post-burn is a valid way to optimise patient selection and risk management when applying a streamlined model of care. A sample of 224 burn patients managed by the Burn Service of Western Australia who provided both short and long-term outcomes was used to estimate the probability of achieving a good QoL defined as 150 out of a possible 160 points on the Burn Specific Health Scale-Brief (BSHS-B) at least six months from injury. A multivariate logistic regression analysis produced a predictive model provisioned as a nomogram for clinical application. A second, independent cohort of consecutive patients (n=106) was used to validate the predictive merit of the nomogram. Male gender (p=0.02), conservative management (p=0.03), upper limb burn (p=0.04) and high BSHS-B score within one month of burn (p<0.001) were significant predictors of good outcome at six months and beyond. A Receiver Operating Curve (ROC) analysis demonstrated excellent (90%) accuracy overall. At 80% probability of good outcome, the false positive risk was 14%. The nomogram was validated by running a second ROC analysis of the model in an independent cohort. The analysis confirmed high (86%) overall accuracy of the model, the risk of false positive was reduced to 10% at a lower (70%) probability. This affirms the stability of the nomogram model in different patient groups over time. An investigation of the effect of missing data on sample selection determined that a greater proportion of younger patients with smaller TBSA burns were excluded due to loss to follow up. For clinicians managing comparable burn populations, the BSWA burns nomogram is an effective tool to assist the selection of patients to a streamlined care pathway with the aim of improving efficiency of service delivery. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Childhood burns in Sulaimaniyah province, Iraqi Kurdistan: a prospective study of admissions and outpatients.

PubMed

Othman, Nasih; Kendrick, Denise; Al-Windi, Ahmad

2015-03-01

While it is globally observed that young children are at a higher risk of burn injuries, little is known about childhood burns in Iraqi Kurdistan. This study was undertaken to describe the epidemiology of burns amongst pre-school children in this region. A prospective study was undertaken from November 2007 to November 2008 involving all children aged 0-5 years attending the burns centre in Sulaimaniyah province for a new burn injury whether treated as an outpatient or admitted to hospital. 1,122 children attended the burns centre of whom 944 (84%) were interviewed (male 53%, female 47%). Mean age was 1.9 years with children aged 1 year comprising 32% and those aged 2 years comprising 21% of the sample. The incidence of burns was 1044/100,000 person-years (1030 in females and 1057 in males). Mechanisms of injury included scalds (80%), contact burns (12%) flames (6%) and other mechanisms (2%). Almost 97% of burns occurred at home including 43% in the kitchen. Winter was the commonest season (36%) followed by autumn (24%). There were 3 peak times of injury during the day corresponding to meal times. The majority of burns were caused by hot water (44%) and tea (20%) and the most common equipment/products responsible were tea utensils (41%). There were 237 admissions with an admission rate of 95 per 100,000 person-years. Scald injuries accounted for most admissions (84%). Median total body surface area affected by the burn or scald (TBSA) was 11% and median hospital stay was 7 days. In-hospital mortality was 8%. Mortality rate was 4% when TBSA was ≤25%, and 100% when TBSA was over 50%. Burn incidence is high in young children especially those aged 1-2 years. Preventive interventions targeted at families with young children & focusing on home safety measures could be effective in reducing childhood burns. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

[The Nutrition Care of Severe Burn Patients].

PubMed

Hsieh, Yu-Hsiu

2016-02-01

In addition to recent advances in burn patient care techniques such as maintaining warm circumambient temperature, the early excision of wounds, and the use of closed dressing, providing nutrition support through early feeding has proven instrumental in greatly increasing the survival rate of burn patients. Severe burns complicated by many factors initiate tremendous physiological stress that leads to postburn hypermetabolism that includes enhanced tissue catabolism, the loss of muscle mass, and decreases in the body's reservoirs of protein and energy. These problems have become the focus of burn therapy. Treating severe burns aims not only to enhance survival rates but also to restore normal bodily functions as completely as possible. Recent research evaluating the application of anabolic agents and immune-enhance formula for severe burns therapy has generated significant controversy. Inadequate caloric intake is one of the main differences among the related studies, with the effect of many special nutrients such as bran acid amides not taken into consideration. Therefore, considering the sufficiency of caloric and protein intake is critical in assessing effectiveness. Only after patients receive adequate calories and protein may the effect of special nutrients such as glutamine and supplements be evaluated effectively.

Photoacoustic diagnosis of burns in rats: two-dimensional photo-acoustic imaging of burned tissue

NASA Astrophysics Data System (ADS)

Yamazaki, Mutsuo; Sato, Shunichi; Saito, Daizo; Okada, Yoshiaki; Kurita, Akira; Kikuchi, Makoto; Ashida, Hiroshi; Obara, Minoru

2003-06-01

We previously reported that for rat burn models, deep dermal burns and deep burns can be well differentiated by measuring the propagation time of the photoacoustic signals originated from the blood in the healthy skin tissue under the damaged tissue layer. However, the diagnosis was based on point measurement in the wound, and therefore site-dependent information on the injuries was not obtained; such information is very important for diagnosis of extended burns. In the present study, we scanned a photoacoustic detector on the wound and constructed two-dimensional (2-D) images of the blood-originated photoacoustic signals for superficial dermal burns (SDB), deep dermal burns (DDB), deep burns (DB), and healthy skins (control) in rats. For each burn model, site-dependent variation of the signal was observed; the variation probably reflects the distribution of blood vessels in the skin tissue. In spite of the variation, clear differentiation was obtained between SDB, DDB, and DB from the 2D images. The images were constructed as a function of post burn time. Temporal signal variation will be also presented.

Quantifying the influence of boreal biomass burning emissions on tropospheric oxidant chemistry over the North Atlantic using BORTAS measurements

NASA Astrophysics Data System (ADS)

Parrington, Mark; Palmer, Paul I.; Rickard, Andrew; Young, Jennifer; Lewis, Ally; Lee, James; Henze, Daven; Tarasick, David; Hyer, Edward; Yantosca, Robert; Bowman, Kevin; Worden, John; Griffin, Debora; Franklin, Jonathan; Helmig, Detlev

2013-04-01

We use the GEOS-Chem chemistry transport model to quantify the impact of boreal biomass burning on tropospheric oxidant chemistry over the North Atlantic region during summer of 2011. The GEOS-Chem model is used at a spatial resolution of 1/2 degree latitude by 2/3 degree longitude for a domain covering eastern North America, the North Atlantic Ocean and western Europe. We initialise the model with biomass burning emissions from the Fire Locating and Monitoring of Burning Emissions (FLAMBE) inventory and use a modified chemical mechanism providing a detailed description of ozone photochemistry in boreal biomass burning outflow derived from the Master Chemical Mechanism (MCM). We evaluate the 3-D model distribution of ozone and tracers associated with biomass burning against measurements made by the UK FAAM BAe-146 research aircraft, ozonesondes, ground-based and satellite instruments as part of the BORTAS experiment between 12 July and 3 August 2011. We also use the GEOS-Chem model adjoint to fit the model to BORTAS measurements to analyse the sensitivity of the model chemical mechanism and ozone distribution to wildfire emissions in central Canada.

Strain-Rate-Free Diffusion Flames: Initiation, Properties, and Quenching

NASA Technical Reports Server (NTRS)

Fendell, Francis; Rungaldier, Harald; Gokoglu, Suleyman; Schultz, Donald

1997-01-01

For about a half century, the stabilization of a steady planar deflagration on a heat-sink-type flat-flame burner has been of extraordinary service for the theoretical modeling and diagnostic probing of combusting gaseous mixtures. However, most engineering devices and most unwanted fire involve the burning of initially unmixed reactants. The most vigorous burning of initially separated gaseous fuel and oxidizer is the diffusion flame. In this useful idealization (limiting case), the reactants are converted to product at a mathematically thin interface, so no interpenetration of fuel and oxidizer occurs. This limit is of practical importance because it often characterizes the condition of optimal performance (and sometimes environmentally objectionable operation) of a combustor. A steady planar diffusion flame is most closely approached in the laboratory in the counterflow apparatus. The utility of this simple-strain-rate flow for the modeling and probing of diffusion flames was noted by Pandya and Weinberg 35 years ago, though only in the last decade or so has its use become internationally common place. However, typically, as the strain rate a is reduced below about 20 cm(exp -1), and the diffusion-flame limit (reaction rate much faster than the flow rate) is approached, the burning is observed to become unstable in earth gravity. The advantageous steady planar flow is not available in the diffusion-flame limit in earth gravity. This is unfortunate because the typical spatial scale in a counterflow is (k/a)(sup 1/2), where k denotes a characteristic diffusion coefficient; thus, the length scale becomes large, and the reacting flow is particularly amenable to diagnostic probing, as the diffusion-flame limit is approached. The disruption of planar symmetry is owing the fact that, as the strain rate a decreases, the residence time (l/a) of the throughput in the counterflow burner increases. Observationally, when the residence time exceeds about 50 msec, the inevitably present convective (Rayleigh-Benard) instabilities, associated with hot-under-cold (flame-under-fresh-reactant) stratification of fluid in a gravitational field, have time to grow to finite amplitude during transit of the burner.

The combustion of large particles of char in bubbling fluidized beds: The dependence of Sherwood number and the rate of burning on particle diameter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dennis, J.S.; Hayhurst, A.N.; Scott, S.A.

Particles of char derived from a variety of fuels (e.g., biomass, sewage sludge, coal, or graphite), with diameters in excess of {approx}1.5mm, burn in fluidized bed combustors containing smaller particles of, e.g., sand, such that the rate is controlled by the diffusion both of O{sub 2} to the burning solid and of the products CO and CO{sub 2} away from it into the particulate phase. It is therefore important to characterize these mass transfer processes accurately. Measurements of the burning rate of char particles made from sewage sludge suggest that the Sherwood number, Sh, increases linearly with the diameter ofmore » the fuel particle, d{sub char} (for d{sub char}>{approx}1.5mm). This linear dependence of Sh on d{sub char} is expected from the basic equation Sh=2{epsilon}{sub mf}(1+d{sub char}/2{delta}{sub diff})/{tau}, provided the thickness of the boundary layer for mass transfer, {delta}{sub diff}, is constant in the region of interest (d{sub char}>{approx}1.5mm). Such a dependence is not seen in the empirical equations currently used and based on the Frossling expression. It is found here that for chars made from sewage sludge (for d{sub char}>{approx}1.5mm), the thickness of the boundary layer for mass transfer in a fluidized bed, {delta}{sub diff}, is less than that predicted by empirical correlations based on the Frossling expression. In fact, {delta}{sub diff} is not more than the diameter of the fluidized sand particles. Finally, the experiments in this study indicate that models based on surface renewal theory should be rejected for a fluidized bed, because they give unrealistically short contact times for packets of fluidized particles at the surface of a burning sphere. The result is the new correlation Sh = 2{epsilon}{sub mf}/{tau} + (A{sub cush}/A{sub char})(d{sub char}/ {delta}{sub diff}) for the dependence of Sh on d{sub char}, the diameter of a burning char particle. This equation is based on there being a gas-cushion of fluidizing gas underneath a burning char particle; the implication of this correlation is that a completely new picture emerges for the combustion of a char particle in a hot fluidized bed. (author)« less

HERMES: A Model to Describe Deformation, Burning, Explosion, and Detonation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reaugh, J E

2011-11-22

HERMES (High Explosive Response to MEchanical Stimulus) was developed to fill the need for a model to describe an explosive response of the type described as BVR (Burn to Violent Response) or HEVR (High Explosive Violent Response). Characteristically this response leaves a substantial amount of explosive unconsumed, the time to reaction is long, and the peak pressure developed is low. In contrast, detonations characteristically consume all explosive present, the time to reaction is short, and peak pressures are high. However, most of the previous models to describe explosive response were models for detonation. The earliest models to describe the responsemore » of explosives to mechanical stimulus in computer simulations were applied to intentional detonation (performance) of nearly ideal explosives. In this case, an ideal explosive is one with a vanishingly small reaction zone. A detonation is supersonic with respect to the undetonated explosive (reactant). The reactant cannot respond to the pressure of the detonation before the detonation front arrives, so the precise compressibility of the reactant does not matter. Further, the mesh sizes that were practical for the computer resources then available were large with respect to the reaction zone. As a result, methods then used to model detonations, known as {beta}-burn or program burn, were not intended to resolve the structure of the reaction zone. Instead, these methods spread the detonation front over a few finite-difference zones, in the same spirit that artificial viscosity is used to spread the shock front in inert materials over a few finite-difference zones. These methods are still widely used when the structure of the reaction zone and the build-up to detonation are unimportant. Later detonation models resolved the reaction zone. These models were applied both to performance, particularly as it is affected by the size of the charge, and to situations in which the stimulus was less than that needed for reliable performance, whether as a result of accident, hazard, or a fault in the detonation train. These models describe the build-up of detonation from a shock stimulus. They are generally consistent with the mesoscale picture of ignition at many small defects in the plane of the shock front and the growth of the resulting hot-spots, leading to detonation in heterogeneous explosives such as plastic-bonded explosives (PBX). The models included terms for ignition, and also for the growth of reaction as tracked by the local mass fraction of product gas, {lambda}. The growth of reaction in such models incorporates a form factor that describes the change of surface area per unit volume (specific surface area) as the reaction progresses. For unimolecular crystalline-based explosives, the form factor is consistent with the mesoscale picture of a galaxy of hot spots burning outward and eventually interacting with each other. For composite explosives and propellants, where the fuel and oxidizer are segregated, the diffusion flame at the fuel-oxidizer interface can be interpreted with a different form factor that corresponds to grains burning inward from their surfaces. The form factor influences the energy release rate, and the amount of energy released in the reaction zone. Since the 19th century, gun and cannon propellants have used perforated geometric shapes that produce an increasing surface area as the propellant burns. This helps maintain the pressure as burning continues while the projectile travels down the barrel, which thereby increases the volume of the hot gas. Interior ballistics calculations use a geometric form factor to describe the changing surface area precisely. As a result, with a suitably modified form factor, detonation models can represent burning and explosion in damaged and broken reactant. The disadvantage of such models in application to accidents is that the ignition term does not distinguish between a value of pressure that results from a shock, and the same pressure that results from a more gradual increase. This disagrees with experiments, where explosives were subjected to a gradual rise in pressure and did not exhibit reaction. More recent models do distinguish between slow pressure rises and shocks, and have had some success in the describing the response of explosives to single and multiple shocks, and the increase of shock sensitivity with porosity, at least over a limited range. The original formulation is appropriate for sustained shocks, but further work is ongoing to describe the response to short pulses. The HERMES model combines features from these prior models. It describes burning and explosion in damaged reactant, and also will develop a detonation if the gradual rise in pressure from burning steepens into a strong-enough shock. The shock strength needed for detonation in a fixed run distance decreases with increasing porosity.« less

A model for assessing water quality risk in catchments prone to wildfire

NASA Astrophysics Data System (ADS)

Langhans, Christoph; Smith, Hugh; Chong, Derek; Nyman, Petter; Lane, Patrick; Sheridan, Gary

2017-04-01

Post-fire debris flows can have erosion rates up to three orders of magnitude higher than background rates. They are major sources of fine suspended sediment, which is critical to the safety of water supply from forested catchments. Fire can cover parts or all of these large catchments and burn severity is often heterogeneous. The probability of spatial and temporal overlap of fire disturbance and rainfall events, and the susceptibility of hillslopes to severe erosion determine the risk to water quality. Here we present a model to calculate recurrence intervals of high magnitude sediment delivery from runoff-generated debris flows to a reservoir in a large catchment (>100 km2) accounting for heterogeneous burn conditions. Debris flow initiation was modelled with indicators of surface runoff and soil surface erodibility. Debris flow volume was calculated with an empirical model, and fine sediment delivery was calculated using simple, expert-based assumptions. In a Monte-Carlo simulation, wildfire was modelled with a fire spread model using historic data on weather and ignition probabilities for a forested catchment in central Victoria, Australia. Multiple high intensity storms covering the study catchment were simulated using Intensity-Frequency-Duration relationships, and the runoff indicator calculated with a runoff model for hillslopes. A sensitivity analysis showed that fine sediment is most sensitive to variables related to the texture of the source material, debris flow volume estimation, and the proportion of fine sediment transported to the reservoir. As a measure of indirect validation, denudation rates of 4.6 - 28.5 mm ka-1 were estimated and compared well to other studies in the region. From the results it was extrapolated that in the absence of fire management intervention the critical sediment concentrations in the studied reservoir could be exceeded in intervals of 18 - 124 years.

[Analysis of distribution and drug resistance of pathogens of burn patients during 9 years].

PubMed

Dou, Y; Zhang, Q

2018-03-20

Objective: To investigate distribution and drug resistance of pathogens of burn patients. Methods: A total of 3 357 strains were cultured and isolated from 25 286 specimens of wounds excretion, deep venous catheters, venous blood, stool, mid-stream urine, sputum, puncture fluid, and throat swab of 11 510 burn patients hospitalized in our burn wards from January 2007 to December 2015. After being identified by API bacteria identification panels and automatically bacteria identification equipment, drug-resistances of Staphylococcus aureus, Pseudomonas aeruginosa, Acinetobacter baumannii, and Klebsiella pneumoniae to 28 common antibiotics were tested by drug sensitivity test with K-B paper disk diffusion method. The WHONET 5.6 software was used to analyze constituent ratio of gram-negative bacteria and gram-positive bacteria in each year, distribution of pathogens in each year, and drug resistance of the above-mentioned 4 pathogens in 9 years to 28 common antibiotics. Data were analyzed by the linear model curve fitting. Results: (1) From 2007 to 2015, constituent ratios of gram-negative bacteria were respectively 41.22% (101/245), 41.88% (165/394), 45.92% (169/368), 42.54% (208/489), 52.35% (267/510), 56.89% (194/341), 58.99% (210/356), 56.95% (172/302), and 50.28% (177/352), with significantly increasing trend ( R (2)=0.625, P <0.05); constituent ratios of gram-positive bacteria were respectively 58.78% (144/245), 58.12% (229/394), 54.08% (199/368), 57.46% (281/489), 47.65% (243/510), 43.11% (147/341), 41.01% (146/356), 43.05% (130/302), 49.72% (175/352), with significantly decreasing trend ( R (2)=0.625, P <0.05). In 9 years, constituent ratio of Staphylococcus aureus ranked the first in all bacteria, and constituent ratios of Pseudomonas aeruginosa and Klebsiella pneumoniae were with significantly increasing trend ( R (2)=0.811, 0.778, P <0.01). (2) In 9 years, drug-resistant rates of Staphylococcus aureus to gentamycin and rifampicin were with significantly decreasing trend ( R (2)=0.727, 0.766, P <0.01); drug-resistant rates of Staphylococcus aureus to phosphonomycin were always in lower levels of 4.6% to 19.5%. In 9 years, drug-resistant rates of Pseudomonas aeruginosa to ceftazidime and ciprofloxacin had no significant change in trend ( R (2)=0.023, <0.001, P >0.05), while drug-resistant rates of Pseudomonas aeruginosa to other 10 common antibiotics were with significantly increasing trend ( R (2)=0.764, 0.793, 0.785, 0.768, 0.752, 0.749, 0.789, 0.786, 0.706, 0.629, P <0.01). In 9 years, drug-resistant rate of Acinetobacter baumannii to ampicillin/sulbactam was with significantly decreasing trend ( R (2)=0.652, P <0.01), and drug-resistant rate of Acinetobacter baumannii to amikacin was with significantly increasing trend ( R (2)=0.531, P <0.05). In 9 years, drug-resistant rates of Klebsiella pneumoniae to piperacillin, ampicillin/sulbactam, cefuroxime, ceftazidime, cefotaxime, cefepime, imipenem, meropenem, amikacin, and gentamicin were with obviously increasing trend ( R (2)=0.481, 0.672, 0.694, 0.532, 0.810, 0.641, 0.809, 0.709, 0.579, 0.810, P <0.05 or P <0.01). Conclusions: Constituent ratios of gram-positive bacteria of Pseudomonas aeruginosa and Klebsiella pneumoniae of burn patients hospitalized in our burn wards from 2007 to 2015 were significantly increased, while constituent ratios of Staphylococcus aureus of those children always ranked the first. Drug-resistence of bacteria of those children in our burn wards was serious. Drug-resistant rate of Staphylococcus aureus only to phosphonomycin was always in lower level. Drug-resistant rates of Pseudomonas aeruginosa to 10 common antibiotics except ceftazidime and ciprofloxacin were significantly increased. Drug-resistant rate of Acinetobacter baumannii only to ampicillin/sulbactam was significantly decreased. Drug-resistant rates of Klebsiella pneumoniae to most common antibiotics were significantly increased.

Vegetation management with fire modifies peatland soil thermal regime.

PubMed

Brown, Lee E; Palmer, Sheila M; Johnston, Kerrylyn; Holden, Joseph

2015-05-01

Vegetation removal with fire can alter the thermal regime of the land surface, leading to significant changes in biogeochemistry (e.g. carbon cycling) and soil hydrology. In the UK, large expanses of carbon-rich upland environments are managed to encourage increased abundance of red grouse (Lagopus lagopus scotica) by rotational burning of shrub vegetation. To date, though, there has not been any consideration of whether prescribed vegetation burning on peatlands modifies the thermal regime of the soil mass in the years after fire. In this study thermal regime was monitored across 12 burned peatland soil plots over an 18-month period, with the aim of (i) quantifying thermal dynamics between burned plots of different ages (from <2 to 15 + years post burning), and (ii) developing statistical models to determine the magnitude of thermal change caused by vegetation management. Compared to plots burned 15 + years previously, plots recently burned (<2-4 years) showed higher mean, maximum and range of soil temperatures, and lower minima. Statistical models (generalised least square regression) were developed to predict daily mean and maximum soil temperature in plots burned 15 + years prior to the study. These models were then applied to predict temperatures of plots burned 2, 4 and 7 years previously, with significant deviations from predicted temperatures illustrating the magnitude of burn management effects. Temperatures measured in soil plots burned <2 years previously showed significant statistical disturbances from model predictions, reaching +6.2 °C for daily mean temperatures and +19.6 °C for daily maxima. Soil temperatures in plots burnt 7 years previously were most similar to plots burned 15 + years ago indicating the potential for soil temperatures to recover as vegetation regrows. Our findings that prescribed peatland vegetation burning alters soil thermal regime should provide an impetus for further research to understand the consequences of thermal regime change for carbon processing and release, and hydrological processes, in these peatlands. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Reaction rate for carbon burning in massive stars

NASA Astrophysics Data System (ADS)

Jiang, C. L.; Santiago-Gonzalez, D.; Almaraz-Calderon, S.; Rehm, K. E.; Back, B. B.; Auranen, K.; Avila, M. L.; Ayangeakaa, A. D.; Bottoni, S.; Carpenter, M. P.; Dickerson, C.; DiGiovine, B.; Greene, J. P.; Hoffman, C. R.; Janssens, R. V. F.; Kay, B. P.; Kuvin, S. A.; Lauritsen, T.; Pardo, R. C.; Sethi, J.; Seweryniak, D.; Talwar, R.; Ugalde, C.; Zhu, S.; Bourgin, D.; Courtin, S.; Haas, F.; Heine, M.; Fruet, G.; Montanari, D.; Jenkins, D. G.; Morris, L.; Lefebvre-Schuhl, A.; Alcorta, M.; Fang, X.; Tang, X. D.; Bucher, B.; Deibel, C. M.; Marley, S. T.

2018-01-01

Carbon burning is a critical phase for nucleosynthesis in massive stars. The conditions for igniting this burning stage, and the subsequent isotope composition of the resulting ashes, depend strongly on the reaction rate for 12C+12C fusion at very low energies. Results for the cross sections for this reaction are influenced by various backgrounds encountered in measurements at such energies. In this paper, we report on a new measurement of 12C+12C fusion cross sections where these backgrounds have been minimized. It is found that the astrophysical S factor exhibits a maximum around Ecm=3.5 -4.0 MeV, which leads to a reduction of the previously predicted astrophysical reaction rate.

Accuracy of Currently Used Paper Burn Diagram vs a Three-Dimensional Computerized Model.

PubMed

Benjamin, Nicole C; Lee, Jong O; Norbury, William B; Branski, Ludwik K; Wurzer, Paul; Jimenez, Carlos J; Benjamin, Debra A; Herndon, David N

Burn units have historically used paper diagrams to estimate percent burn; however, unintentional errors can occur. The use of a computer program that incorporates wound mapping from photographs onto a three-dimensional (3D) human diagram could decrease subjectivity in preparing burn diagrams and subsequent calculations of TBSA burned. Analyses were done on 19 burned patients who had an estimated TBSA burned of ≥20%. The patients were admitted to Shriners Hospitals for Children or the University of Texas Medical Branch in Galveston, Texas, from July 2012 to September 2013 for treatment. Digital photographs were collected before the patient's first surgery. Using BurnCase 3D (RISC Software GmbH, Hagenberg, Austria), a burn mapping software, the user traced partial- and full-thickness burns from photographs. The program then superimposed tracings onto a 3D model and calculated percent burned. The results were compared with the Lund and Browder diagrams completed after the first operation. A two-tailed t-test was used to calculate statistical differences. For partial-thickness burns, burn sizes calculated using Lund and Browder diagrams were significantly larger than those calculated using BurnCase 3D (15% difference, P < .01). The opposite was found for full-thickness burns, with burn sizes being smaller when calculated using Lund and Browder diagrams (11% difference, P < .05). In conclusion, substantial differences exist in percent burn estimations derived from BurnCase 3D and paper diagrams. In our studied cohort, paper diagrams were associated with overestimation of partial-thickness burn size and underestimation of full-thickness burn size. Additional studies comparing BurnCase 3D with other commonly used methods are warranted.

Propranolol and Oxandrolone Therapy Accelerated Muscle Recovery in Burned Children.

PubMed

Chao, Tony; Porter, Craig; Herndon, David N; Siopi, Aikaterina; Ideker, Henry; Mlcak, Ronald P; Sidossis, Labros S; Suman, Oscar E

2018-03-01

Severe burns result in prolonged hypermetabolism and skeletal muscle catabolism. Rehabilitative exercise training (RET) programs improved muscle mass and strength in severely burned children. The combination of RET with β-blockade or testosterone analogs showed improved exercise-induced benefits on body composition and muscle function. However, the effect of RET combined with multiple drug therapy on muscle mass, strength, cardiorespiratory fitness, and protein turnover are unknown. In this placebo-controlled randomized trial, we hypothesize that RET combined with oxandrolone and propranolol (Oxprop) will improve muscle mass and function and protein turnover in severely burned children compared with burned children undergoing the same RET with a placebo. We studied 42 severely burned children (7-17 yr) with severe burns over 30% of the total body surface area. Patients were randomized to placebo (22 control) or to Oxprop (20) and began drug administration within 96 h of admission. All patients began RET at hospital discharge as part of their standardized care. Muscle strength (N·m), power (W), V˙O2peak, body composition, and protein fractional synthetic rate and fractional breakdown rate were measured pre-RET (PRE) and post-RET (POST). Muscle strength and power, lean body mass, and V˙O2peak increased with RET in both groups (P < 0.01). The increase in strength and power was significantly greater in Oxprop versus control (P < 0.01), and strength and power was greater in Oxprop over control POST (P < 0.05). Fractional synthetic rate was significantly higher in Oxprop than control POST (P < 0.01), resulting in improved protein net balance POST (P < 0.05). Rehabilitative exercise training improves body composition, muscle function, and cardiorespiratory fitness in children recovering from severe burns. Oxprop therapy augments RET-mediated improvements in muscle strength, power, and protein turnover.

[Etiological analysis of subambient temperature burn in 351 cases of Hefei area].

PubMed

Shi, Jie; Qi, Weiwei; Xu, Qinglian; Zhou, Shunying; Wang, Guobao

2010-06-01

To study the preventive measure of the subambient temperature burn by analysing the pathogenesis feature. The clinical data were analysed from 351 cases of subambient temperature burn between February 2004 and February 2009, including age, sex, burn season, burn factors, burn position, burn area, burn degree, treatment way, and wound healing. Subambient temperature burn occurred in every age stage. The susceptible age stages included infant, children, and the elderly. Female patients were more than male patients. The common burn reasons were hot-water bottle burn, honey warm keeper burn, and heating device burn. The peak season was winter. Lower limb was the most common site of the subambient temperature burn. The deep II degree to III degree were the most common level, and the burn area was always small, often < or = 1% of total body surface area. Most of patients were treated with changing dressings at clinic and few patients needed hospitalization. Though the surface of wound could heal finally, and the wound healed well with no obvious scar in patients who received operation. Subambient temperature burn is the frequently encountered disease in winter. Use of the warming articles should be cautious, at the same time safety awareness should be strengthened so as to decrease the incidence rate of subambient temperature burn and the injury degree.

Impact of burned areas on the northern African seasonal climate from the perspective of regional modeling

NASA Astrophysics Data System (ADS)

De Sales, Fernando; Xue, Yongkang; Okin, Gregory S.

2016-12-01

This study investigates the impact of burned areas on the surface energy balance and monthly precipitation in northern Africa as simulated by a state-of-the-art regional model. Mean burned area fraction derived from MODIS date of burning product was implemented in a set of 1-year long WRF-NMM/SSiB2 model simulations. Vegetation cover fraction and LAI were degraded daily based on mean burned area fraction and on the survival rate for each vegetation land cover type. Additionally, ground darkening associated with wildfire-induced ash and charcoal deposition was imposed through lower ground albedo for a period after burning. In general, wildfire-induced vegetation and ground condition deterioration increased mean surface albedo by exposing the brighter bare ground, which in turn caused a decrease in monthly surface net radiation. On average, the wildfire-season albedo increase was approximately 6.3 % over the Sahel. The associated decrease in surface available energy caused a drop in surface sensible heat flux to the atmosphere during the dry months of winter and early spring, which gradually transitioned to a more substantial decrease in surface evapotranspiration in April and May that lessened throughout the rainy season. Overall, post-fire land condition deterioration resulted in a decrease in precipitation over sub-Saharan Africa, associated with the weakening of the West African monsoon progression through the region. A decrease in atmospheric moisture flux convergence was observed in the burned area simulations, which played a dominant role in reducing precipitation in the area, especially in the months preceding the monsoon onset. The areas with the largest precipitation impact were those covered by savannas and rainforests, where annual precipitation decreased by 3.8 and 3.3 %, respectively. The resulting precipitation decrease and vegetation deterioration caused a drop in gross primary productivity in the region, which was strongest in late winter and early spring. This study suggests the cooling and drying of atmosphere induced by burned areas caused the strengthening of subsidence during pre-onset and weakening of upward atmospheric motion during onset and mature stages of the monsoon leading to a waning of convective instability and precipitation. Monthly mid-tropospheric vertical wind showed a strengthening of downward motion in winter and spring seasons, and weakening of upward movement during the rainy months. Furthermore, precipitation energy analysis revealed that most of precipitation decrease originated from convective events, which supports the hypothesis of reduced convective instability due to wildfires.

The evolution of massive stars and their spectra. I. A non-rotating 60 M⊙ star from the zero-age main sequence to the pre-supernova stage

NASA Astrophysics Data System (ADS)

Groh, Jose H.; Meynet, Georges; Ekström, Sylvia; Georgy, Cyril

2014-04-01

For the first time, the interior and spectroscopic evolution of a massive star is analyzed from the zero-age main sequence (ZAMS) to the pre-supernova (SN) stage. For this purpose, we combined stellar evolution models using the Geneva code and stellar atmospheric/wind models using CMFGEN. With our approach, we were able to produce observables, such as a synthetic high-resolution spectrum and photometry, thereby aiding the comparison between evolution models and observed data. Here we analyze the evolution of a non-rotating 60 M⊙ star and its spectrum throughout its lifetime. Interestingly, the star has a supergiant appearance (luminosity class I) even at the ZAMS. We find the following evolutionary sequence of spectral types: O3 I (at the ZAMS), O4 I (middle of the H-core burning phase), B supergiant (BSG), B hypergiant (BHG), hot luminous blue variable (LBV; end of H-core burning), cool LBV (H-shell burning through the beginning of the He-core burning phase), rapid evolution through late WN and early WN, early WC (middle of He-core burning), and WO (end of He-core burning until core collapse). We find the following spectroscopic phase lifetimes: 3.22 × 106 yr for the O-type, 0.34 × 105 yr (BSG), 0.79 × 105 yr (BHG), 2.35 × 105 yr (LBV), 1.05 × 105 yr (WN), 2.57 × 105 yr (WC), and 3.80 × 104 yr (WO). Compared to previous studies, we find a much longer (shorter) duration for the early WN (late WN) phase, as well as a long-lived LBV phase. We show that LBVs arise naturally in single-star evolution models at the end of the MS when the mass-loss rate increases as a consequence of crossing the bistability limit. We discuss the evolution of the spectra, magnitudes, colors, and ionizing flux across the star's lifetime, and the way they are related to the evolution of the interior. We find that the absolute magnitude of the star typically changes by ~6 mag in optical filters across the evolution, with the star becoming significantly fainter in optical filters at the end of the evolution, when it becomes a WO just a few 104 years before the SN explosion. We also discuss the origin of the different spectroscopic phases (i.e., O-type, LBV, WR) and how they are related to evolutionary phases (H-core burning, H-shell burning, He-core burning). Tables 1, 4 and 5 are available in electronic form at http://www.aanda.orgSynthetic spectra are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/564/A30

Using multilevel spatial models to understand salamander site occupancy patterns after wildfire

USGS Publications Warehouse

Chelgren, Nathan; Adams, Michael J.; Bailey, Larissa L.; Bury, R. Bruce

2011-01-01

Studies of the distribution of elusive forest wildlife have suffered from the confounding of true presence with the uncertainty of detection. Occupancy modeling, which incorporates probabilities of species detection conditional on presence, is an emerging approach for reducing observation bias. However, the current likelihood modeling framework is restrictive for handling unexplained sources of variation in the response that may occur when there are dependence structures such as smaller sampling units that are nested within larger sampling units. We used multilevel Bayesian occupancy modeling to handle dependence structures and to partition sources of variation in occupancy of sites by terrestrial salamanders (family Plethodontidae) within and surrounding an earlier wildfire in western Oregon, USA. Comparison of model fit favored a spatial N-mixture model that accounted for variation in salamander abundance over models that were based on binary detection/non-detection data. Though catch per unit effort was higher in burned areas than unburned, there was strong support that this pattern was due to a higher probability of capture for individuals in burned plots. Within the burn, the odds of capturing an individual given it was present were 2.06 times the odds outside the burn, reflecting reduced complexity of ground cover in the burn. There was weak support that true occupancy was lower within the burned area. While the odds of occupancy in the burn were 0.49 times the odds outside the burn among the five species, the magnitude of variation attributed to the burn was small in comparison to variation attributed to other landscape variables and to unexplained, spatially autocorrelated random variation. While ordinary occupancy models may separate the biological pattern of interest from variation in detection probability when all sources of variation are known, the addition of random effects structures for unexplained sources of variation in occupancy and detection probability may often more appropriately represent levels of uncertainty. ?? 2011 by the Ecological Society of America.

40 CFR Table 8 to Subpart Dddd of... - Model Rule-Emission Limitations That Apply to Waste-Burning Kilns After May 20, 2011

Code of Federal Regulations, 2011 CFR

2011-07-01

... Apply to Waste-Burning Kilns After May 20, 2011 8 Table 8 to Subpart DDDD of Part 60 Protection of..., Table 8 Table 8 to Subpart DDDD of Part 60—Model Rule—Emission Limitations That Apply to Waste-Burning... to Waste-Burning Kilns After May 20, 2011 For the air pollutant You must meet this emissionlimitation...

Carbon fluxes in ecosystems of Yellowstone National Park predicted from remote sensing data and simulation modeling

PubMed Central

2011-01-01

Background A simulation model based on remote sensing data for spatial vegetation properties has been used to estimate ecosystem carbon fluxes across Yellowstone National Park (YNP). The CASA (Carnegie Ames Stanford Approach) model was applied at a regional scale to estimate seasonal and annual carbon fluxes as net primary production (NPP) and soil respiration components. Predicted net ecosystem production (NEP) flux of CO2 is estimated from the model for carbon sinks and sources over multi-year periods that varied in climate and (wildfire) disturbance histories. Monthly Enhanced Vegetation Index (EVI) image coverages from the NASA Moderate Resolution Imaging Spectroradiometer (MODIS) instrument (from 2000 to 2006) were direct inputs to the model. New map products have been added to CASA from airborne remote sensing of coarse woody debris (CWD) in areas burned by wildfires over the past two decades. Results Model results indicated that relatively cooler and wetter summer growing seasons were the most favorable for annual plant production and net ecosystem carbon gains in representative landscapes of YNP. When summed across vegetation class areas, the predominance of evergreen forest and shrubland (sagebrush) cover was evident, with these two classes together accounting for 88% of the total annual NPP flux of 2.5 Tg C yr-1 (1 Tg = 1012 g) for the entire Yellowstone study area from 2000-2006. Most vegetation classes were estimated as net ecosystem sinks of atmospheric CO2 on annual basis, making the entire study area a moderate net sink of about +0.13 Tg C yr-1. This average sink value for forested lands nonetheless masks the contribution of areas burned during the 1988 wildfires, which were estimated as net sources of CO2 to the atmosphere, totaling to a NEP flux of -0.04 Tg C yr-1 for the entire burned area. Several areas burned in the 1988 wildfires were estimated to be among the lowest in overall yearly NPP, namely the Hellroaring Fire, Mink Fire, and Falls Fire areas. Conclusions Rates of recovery for burned forest areas to pre-1988 biomass levels were estimated from a unique combination of remote sensing and CASA model predictions. Ecosystem production and carbon fluxes in the Greater Yellowstone Ecosystem (GYE) result from complex interactions between climate, forest age structure, and disturbance-recovery patterns of the landscape. PMID:21835025

Carbon fluxes in ecosystems of Yellowstone National Park predicted from remote sensing data and simulation modeling.

PubMed

Potter, Christopher; Klooster, Steven; Crabtree, Robert; Huang, Shengli; Gross, Peggy; Genovese, Vanessa

2011-08-11

A simulation model based on remote sensing data for spatial vegetation properties has been used to estimate ecosystem carbon fluxes across Yellowstone National Park (YNP). The CASA (Carnegie Ames Stanford Approach) model was applied at a regional scale to estimate seasonal and annual carbon fluxes as net primary production (NPP) and soil respiration components. Predicted net ecosystem production (NEP) flux of CO2 is estimated from the model for carbon sinks and sources over multi-year periods that varied in climate and (wildfire) disturbance histories. Monthly Enhanced Vegetation Index (EVI) image coverages from the NASA Moderate Resolution Imaging Spectroradiometer (MODIS) instrument (from 2000 to 2006) were direct inputs to the model. New map products have been added to CASA from airborne remote sensing of coarse woody debris (CWD) in areas burned by wildfires over the past two decades. Model results indicated that relatively cooler and wetter summer growing seasons were the most favorable for annual plant production and net ecosystem carbon gains in representative landscapes of YNP. When summed across vegetation class areas, the predominance of evergreen forest and shrubland (sagebrush) cover was evident, with these two classes together accounting for 88% of the total annual NPP flux of 2.5 Tg C yr-1 (1 Tg = 1012 g) for the entire Yellowstone study area from 2000-2006. Most vegetation classes were estimated as net ecosystem sinks of atmospheric CO2 on annual basis, making the entire study area a moderate net sink of about +0.13 Tg C yr-1. This average sink value for forested lands nonetheless masks the contribution of areas burned during the 1988 wildfires, which were estimated as net sources of CO2 to the atmosphere, totaling to a NEP flux of -0.04 Tg C yr-1 for the entire burned area. Several areas burned in the 1988 wildfires were estimated to be among the lowest in overall yearly NPP, namely the Hellroaring Fire, Mink Fire, and Falls Fire areas. Rates of recovery for burned forest areas to pre-1988 biomass levels were estimated from a unique combination of remote sensing and CASA model predictions. Ecosystem production and carbon fluxes in the Greater Yellowstone Ecosystem (GYE) result from complex interactions between climate, forest age structure, and disturbance-recovery patterns of the landscape.

[Influence of three-level collaboration network of pediatric burns treatment in Anhui province on treatment effects of burn children].

PubMed

Xia, Z G; Zhou, X L; Kong, W C; Li, X Z; Song, J H; Fang, L S; Hu, D L; Cai, C; Tang, Y Z; Yu, Y X; Wang, C H; Xu, Q L

2018-03-20

Objective: To explore the influence of three-level collaboration network of pediatric burns in Anhui province on treatment effects of burn children. Methods: The data of medical records of pediatric burn children transferred from Lu'an People's Hospital and Fuyang People's Hospital to the First Affiliated Hospital of Anhui Medical University from January 2014 to December 2015 and January 2016 to September 2017 (before and after establishing three-level collaboration network of pediatric burns treatment) were analyzed: percentage of transferred burn children to hospitalized burn children in corresponding period, gender, age, burn degree, treatment method, treatment result, occurrence and treatment result of shock, and operative and non-operative treatment time and cost. Rehabilitation result of burn children transferred back to local hospitals in 2016 and 2017. Data were processed with t test, chi-square test, Mann-Whitney U test, and Fisher's exact test. Results: (1) Percentage of burn children transferred from January 2014 to December 2015 was 34.3% (291/848) of the total number of hospitalized burn children in the same period of time, which was close to 30.4% (210/691) of burn children transferred from January 2016 to September 2017 ( χ (2)=2.672, P >0.05). (2) Gender, age, burn degree, and treatment method of burn children transferred from the two periods of time were close ( χ (2)=3.382, Z =-1.917, -1.911, χ (2)=3.133, P >0.05). (3) Cure rates of children with mild, moderate, and severe burns transferred from January 2016 to September 2017 were significantly higher than those of burn children transferred from January 2014 to December 2015 ( χ (2)=11.777, 6.948, 4.310, P <0.05). Cure rates of children with extremely severe burns transferred from the two periods of time were close ( χ (2)=1.181, P >0.05). (4) Children with mild and moderate burns transferred from the two periods of time were with no shock. The incidence of shock of children with severe burns transferred from January 2014 to December 2015 was 6.0% (4/67), and 3 children among them were cured. The incidence of shock of children with severe burns transferred from January 2016 to September 2017 was 3.9% (2/51), and both children were cured. The incidences and cures of shock of children with severe burns transferred from the two periods of time were close ( χ (2)=0.006, P >0.05). Incidence of shock of children with extremely severe burns transferred from January 2014 to December 2015 was 57.1% (32/56), significantly higher than that of burn children transferred from January 2016 to September 2017 [34.5% (10/29), χ (2)=3.925, P <0.05]. Shock of 25 children with extremely severe burns transferred from January 2014 to December 2015 were cured, and shock of 9 children with extremely severe burns transferred from January 2016 to September 2017 were cured. The cures of shock of children with extremely severe burns transferred from the two periods of time were close ( χ (2)=0.139, P >0.05). (5) Time of operative treatment of children with moderate, severe, and extremely severe burns transferred from January 2014 to December 2015 was obviously longer than that of burn children transferred from January 2016 to September 2017 ( t =2.335, 2.065, 2.310, P <0.05). Time of operative treatment of children with mild burns transferred from the two periods of time was close ( Z =-0.417, P >0.05). Costs of operative treatment of children with moderate and severe burns transferred from January 2014 to December 2015 were significantly more than those of burn children transferred from January 2016 to September 2017 ( Z =-3.324, t =2.167, P <0.05). Costs of operative treatment of children with mild and extremely severe burns transferred from the two periods of time were close ( t =0.627, 0.808, P >0.05). (6)Time of non-operative treatment of children with mild, moderate, and severe burns transferred from January 2014 to December 2015 was obviously longer than that of burn children transferred from January 2016 to September 2017 ( t =2.335, Z =-2.095, t =2.152, P <0.05). Time of non-operative treatment of children with extremely severe burns transferred from the two periods of time was close ( t =0.450, P >0.05). Costs of non-operative treatment of children with moderate and severe burns transferred from January 2014 to December 2015 were obviously higher than those of burn children transferred from January 2016 to September 2017 ( Z =-2.164, t =2.040, P <0.05). Costs of non-operative treatment of children with mild and extremely severe burns transferred from the two periods of time were close ( t =0.146, 1.235, P >0.05). (7) Sixty-seven burn children transferred from January 2016 to September 2017 were transferred back to local hospitals for rehabilitation under the guidance of experts of the First Affiliated Hospital of Anhui Medical University, with 25 patients in 2016 and 42 patients in 2017. Effective rehabilitation rates of burn children transferred back to local hospitals for rehabilitation in 2016 and 2017 were both 100%. Conclusions: The three-level collaboration network of pediatric burns treatment in Anhui province can effectively increase cure rate of children with mild, moderate, and severe burns, reduce incidence of shock of children with extremely severe burns, shorten time of operative treatment of burn children with moderate, severe, and extremely severe burns, and time of non-operative treatment of children with mild, moderate, and severe burns, reduce treatment costs of children with moderate and severe burns, and improve rehabilitation effectiveness of children transferred from Lu'an People's Hospital and Fuyang People's Hospital to the the First Affiliated Hospital of Anhui Medical University.

Nitrogen oxides from burning forest fuels examined by thermogravimetry and evolved gas analysis

Treesearch

H.B. Clements; Charles K. McMahon

1980-01-01

Abstract. Twelve forest fuels that varied widely in nitrogen content were burned in a thermogravimetric system, and nitrogen oxide production was analyzed by chemiluminescence. The effects of fuel nitrogen concentration, available oxygen, flow rate, and heating rate on nitrogen oxide production were examined.Results show that fuel nitrogen is an...

EFFECTS OF BURN RATE, WOOD SPECIES, MOISTURE CONTENT AND WEIGHT OF WOOD LOADED ON WOODSTOVE EMISSIONS

EPA Science Inventory

The report gives results of tests of four woodstove operating parameters (burn rate, wood moisture, wood load, and wood species) at two levels each using a half factorial experimental test design to determine statistically significant effects on the emission components CO, CO2, p...

How Does the Freezer Burn Our Food?

ERIC Educational Resources Information Center

Schmidt, Shelly J.; Lee, Joo Won

2009-01-01

Freezer burn is a common problem that significantly affects the color, texture, and flavor of frozen foods. Food science students should be able to clearly explain the causes and consequences of freezer burn. However, it is difficult to find a modern, detailed, accurate, yet concise, explanation of the mechanism and factors influencing the rate of…

Refinement of Propellant Strand Burning Method to Suit Aluminised Composite Rocket Propellant

DTIC Science & Technology

2014-12-01

from discrete burn rates at each pressure. Strands are ignited with a nickel- chromium (nichrome) wire with burn time measured via timing wires which...Application of Paint Inhibitor 8.5.1 Switch on the fume hood and prepare a 70% dilution of inhibitor paint as per instructions of document 3.5

Experimental investigation of burning rates of pure ethanol and ethanol blended fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parag, Shintre; Raghavan, Vasudevan

2009-05-15

A fundamental experimental study to determine the burning rates of ethanol and ethanol-blended fossil fuels is presented. Pure liquid ethanol or its blends with liquid fossil fuels such as gasoline or diesel, has been transpired to the surface a porous sphere using an infusion pump. Burning of the fuel takes place on the surface of the porous sphere, which is placed in an air stream blowing upwards with a uniform velocity at atmospheric pressure and temperature under normal gravity conditions. At low air velocities, when ignited, a flame envelopes the sphere. For each sphere size, air stream velocity and fuelmore » type, the fuel feed rate will vary and the same is recorded as the burning rate for that configuration. The flame stand-off distances from the sphere surface are measured by post-processing the digital image of the flame photograph using suitable imaging software. The transition velocity at which the flame moves and establishes itself at the wake region of the sphere has been determined for different diameters and fuel types. Correlations of these parameters are also presented. (author)« less

Perceptual and Affective Responses to Sampled Capsaicin Differ by Reported Intake

PubMed Central

Nolden, Alissa A.; Hayes, John E.

2016-01-01

The present study was conducted to a) generate suprathresold dose-response functions for multiple qualities evoked by capsaicin across a wide range of concentrations, and b) revisit how intensity ratings and liking may differ as a function of self reported intake. Individuals rated eight samples of capsaicin for perceived burn and bitterness, as well as disliking/liking. Measures of reported preference for chili peppers, chili intake frequency, prior experience and personality measures were also assessed. Here, we confirm prior findings showing that burn in the laboratory differs with reported chili intake, with infrequent consumers reporting more burn. We extend these findings by exploring how capsaicin perception varies by reported liking, and measures of variety seeking. We also address the question of whether differences in burn ratings may potentially be an artifact of differential scale usage across groups due to prior experience, and not chronic desensitization, as is typically assumed. By using generalized scaling methods and recalled sensations, we conclude the differences observed here and elsewhere are not likely due to differences in how participants use rating scales. PMID:28392628

Chemistry resolved kinetic flow modeling of TATB based explosives

NASA Astrophysics Data System (ADS)

Vitello, Peter; Fried, Laurence E.; William, Howard; Levesque, George; Souers, P. Clark

2012-03-01

Detonation waves in insensitive, TATB-based explosives are believed to have multiple time scale regimes. The initial burn rate of such explosives has a sub-microsecond time scale. However, significant late-time slow release in energy is believed to occur due to diffusion limited growth of carbon. In the intermediate time scale concentrations of product species likely change from being in equilibrium to being kinetic rate controlled. We use the thermo-chemical code CHEETAH linked to an ALE hydrodynamics code to model detonations. We term our model chemistry resolved kinetic flow, since CHEETAH tracks the time dependent concentrations of individual species in the detonation wave and calculates EOS values based on the concentrations. We present here two variants of our new rate model and comparison with hot, ambient, and cold experimental data for PBX 9502.

Clothing-related burns in New South Wales, Australia: impact of legislation on a continuing problem.

PubMed

Harvey, Lara A; Connolley, Siobhan; Harvey, John G

2015-02-01

To combat the risk of nightwear burns a mandatory standard regulating the design, flammability and labelling requirements of children's nightwear was introduced in Australia in 1987. This population-based study examined the trends, characteristics and causes of clothing-related burns to inform a review of the current standard, and to facilitate the development of targeted prevention strategies. Clothing-related burns for 1998-2013 were identified from hospitalisation data for all hospitals in NSW and detailed information regarding circumstance of injury from a burn data registry. To investigate percentage annual change (PAC) in trends negative binomial regression analysis was performed. There were 541 hospitalisations for clothing-related burns, 18% were nightwear-related and 82% were for other clothing. All clothing burns decreased by an estimated 4% per year (95% CI -6.2 to -2.1). Nightwear-related burns decreased by a significantly higher rate (PAC -7.4%; 95% CI -12.5 to -2.1) than other clothing (PAC -2.5%; 95%CI -4.7 to -0.1). Exposure to open heat source (campfire/bonfire) was the most common cause, followed by cooking. Of factors known to be associated with clothing burns, accelerant use was reported in 27% of cases, cigarettes 17%, loose skirt or dress 8%, and angle grinders in 6% of cases. Hospitalisations for clothing burns are relatively uncommon in NSW and rates, particularly of nightwear burns, have decreased over the last 15 years. Strategies for continued reduction of these injuries include increasing the scope of the current clothing standard or developing new standards to include all children's clothing and adult nightwear, and increasing community awareness of the risk associated with open heat sources, accelerant use and loose clothing. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

The Burns Registry of Australia and New Zealand: progressing the evidence base for burn care.

PubMed

Cleland, Heather; Greenwood, John E; Wood, Fiona M; Read, David J; Wong She, Richard; Maitz, Peter; Castley, Andrew; Vandervord, John G; Simcock, Jeremy; Adams, Christopher D; Gabbe, Belinda J

2016-03-21

Analysis of data from the Burns Registry of Australia and New Zealand (BRANZ) to determine the extent of variation between participating units in treatment and in specific outcomes during the first 4 years of its operation. BRANZ, an initiative of the Australian and New Zealand Burn Association, is a clinical quality registry developed in accordance with the Australian Commission on Safety and Quality in Healthcare national operating principles. Patients with burn injury who fulfil pre-defined criteria are transferred to and managed in designated burn units. There are 17 adult and paediatric units in Australia and New Zealand that manage almost all patients with significant burn injury. Twelve of these units treat adult patients. Data on 7184 adult cases were contributed by ten acute adult burn units to the registry between July 2010 and June 2014.Major outcomes: In-hospital mortality, hospital length of stay, skin grafting rates, and rates of admission to intensive care units. Considerable variations in unit profiles (including numbers of patients treated), in treatment and in outcomes were identified. Despite the highly centralised delivery of care to patients with severe or complex burn injury, and the relatively small number of specialist burn units, we found significant variation between units in clinical management and in outcomes. BRANZ data from its first 4 years of operation support its feasibility and the value of further development of the registry. Based on these results, the focus of ongoing research is to improve understanding of the reasons for variations in practice and of their effect on outcomes for patients, and to develop evidence-informed clinical guidelines for burn management in Australia and New Zealand.

Photoacoustic signal measurement for burned skins in the spectral range of 500-650 nm: experiment with rat burn models

NASA Astrophysics Data System (ADS)

Yamazaki, Mutsuo; Sato, Shunichi; Saito, Daizo; Fujita, Masanori; Okada, Yoshiaki; Kikuchi, Makoto; Ashida, Hiroshi; Obara, Minoru

2002-06-01

This paper reports the burn diagnosis that is based on the measurement of photoacoustic waves from skin, where the acoustic waves originate from the absorption of light by blood. For this purpose, a transducer composed of a ring-shaped piezoelectric film and a quartz fiber was made. An optical parametric oscillator (500 - 650 nm) was used as a light source and its output pulses were coupled to the quartz fiber. To investigate the optimum light wavelength, we conducted experiments using rat burn models. We demonstrated that the superficial dermal burn (SDB), deep dermal burn (DDB), deep burn (DB), and control (healthy skin) could be clearly differentiated based on the photoacoustic signals induced by the light of 532 - 580nm.

Climate vs. carbon dioxide controls on biomass burning: a model analysis of the glacial-interglacial contrast

NASA Astrophysics Data System (ADS)

Calvo, M. Martin; Prentice, I. C.; Harrison, S. P.

2014-02-01

Climate controls fire regimes through its influence on the amount and types of fuel present and their dryness; CO2 availability, in turn, constrains primary production by limiting photosynthetic activity in plants. However, although fuel accumulation depends on biomass production, and hence CO2 availability, the links between atmospheric CO2 and biomass burning are not well known. Here a fire-enabled dynamic global vegetation model (the Land surface Processes and eXchanges model, LPX) is used to attribute glacial-interglacial changes in biomass burning to CO2 increase, which would be expected to increase primary production and therefore fuel loads even in the absence of climate change, vs. climate change effects. Four general circulation models provided Last Glacial Maximum (LGM) climate anomalies - that is, differences from the pre-industrial (PI) control climate - from the Palaeoclimate Modelling Intercomparison Project Phase 2, allowing the construction of four scenarios for LGM climate. Modelled carbon fluxes in biomass burning were corrected for the model's observed biases in contemporary biome-average values. With LGM climate and low CO2 (185 ppm) effects included, the modelled global flux was 70 to 80% lower at the LGM than in PI time. LGM climate with pre-industrial CO2 (280 ppm) however yielded unrealistic results, with global and Northern Hemisphere biomass burning fluxes greater than in the pre-industrial climate. Using the PI CO2 concentration increased the modelled LGM biomass burning fluxes for all climate models and latitudinal bands to between four and ten times their values under LGM CO2 concentration. It is inferred that a substantial part of the increase in biomass burning after the LGM must be attributed to the effect of increasing CO2 concentration on productivity and fuel load. Today, by analogy, both rising CO2 and global warming must be considered as risk factors for increasing biomass burning. Both effects need to be included in models to project future fire risks.

Prediction of ISO 9705 Room/Corner Test Results. Volume 1

DTIC Science & Technology

1999-11-01

spread rates depend on the flame length , so that it is not a unique function of the material being burned. The flame spread model developed by Mowrer and...height is expressed as: = kf (5) xp -X16 16I The parameter, kf is a correlating factor used to define the flame length . Cleary and Quintiere (1991

Modeling nest survival of cavity-nesting birds in relation to postfire salvage logging

Treesearch

Vicki Saab; Robin E. Russell; Jay Rotella; Jonathan G. Dudley

2011-01-01

Salvage logging practices in recently burned forests often have direct effects on species associated with dead trees, particularly cavity-nesting birds. As such, evaluation of postfire management practices on nest survival rates of cavity nesters is necessary for determining conservation strategies. We monitored 1,797 nests of 6 cavity-nesting bird species: Lewis'...

Integral Ramjet Booster Demonstration Program

DTIC Science & Technology

1975-02-01

Table 3-10 THREE-COMPONENT DECOMPOSITION MODEL Component r0 Ibm ;"-3 7ft Ibm ^ft A (Resin) 60.75 B (Resin) 20.24 C (Reinf.) 110.00...Cured Strands Burn rate 1000 psia/ + 70°F, in./sec Pressure exponent o. (-65 to +1600F), %/"F itP , (-65 to tUCF), ü/8» Ballistic Properties, 6

The Protective Effects of Epigallocatechin Gallate Against Distant Organ Damage After Severe Skin Burns--Experimental Study Using a Rat Model of Thermal Trauma.

PubMed

Hosnuter, Mubin; Melikoglu, Cenk; Aslan, Cem; Saglam, Gulcan; Sutcu, Recep

2015-01-01

Epigallocatechin gallate (EGCG), a green tea polyphenol, has potent antioxidant properties. The purpose of the present study was to examine the possible preventative effects of EGCG against internal organ injury due to large-surface skin burns in a rat model. The study design involved three groups of rats: a sham group and two groups with 25-30% full-thickness burns: (a) the sham group without burns or treatment (n=18); (b) the control burn group (burns+sterile saline, n=18); and (c) the burn treatment group (burns+treatment with EGCG, n=18). EGCG was administered intraperitoneally immediately after the thermal injury, and daily in 100 μmol/kg doses. Kidney and lung tissue samples were taken to determine the levels of malondialdehyde (MDA), superoxide dismutase (SOD), tumor necrosis factor-α (TNF-α), and glutathione peroxidase (GPX) after the first, third and seventh post-burn days. In the EGCG-treated burn group, SOD and GPX activity were significantly higher than in the burn control group. Additionally, MDA and TNF-α levels were significantly lower in the EGCG-treated burn group. Based on this study, it might be anticipated that EGCG treatment may be beneficial in burn injury cases.

Epidemiology and Outcomes of Hospitalized Burn Patients in Gaza Strip: A Descriptive Study.

PubMed

Elsous, Aymen; Ouda, Mahmoud; Mohsen, Samah; Al-Shaikh, Mohammed; Mokayad, Siham; Abo-Shaban, Nafiz; Hamad, Abed Al-Rahman

2016-01-01

Burns are serious health problems and leading causes of mortality and morbidity in the Eastern Mediterranean Region. This study aimed to overview the epidemiological profile and to present outcomes among hospitalized burn patients in AL Alamy burn center in Gaza. This was a cross-sectional retrospective study of medical records of hospitalized patients from July 2013 to June 2014. Descriptive analysis for studied variables was applied and P ≤ 0.05 considered statistically significant. One humdred eighty nime admissions, 60.8% were males and 63% were under 10 years old. Burn patients in the age range between 19-40 years represented 25.9%. Most common burn injuries were accidental (86.2%), located at home (88.9%), caused by scald (66.1%) and by fire flame (23.8%). On admission, the majority of cases presented with second degree burn (45.5%) or mixed burn (38.6%). The mean TBSA was 11.86 (SD ± 10.78) ranging from 1% to 75% whereas, the mean hospital length of stay was 11.45 (SD ± 12.60) ranging from 1 to 115 days. Total in hospital mortality rate was 2.1% and length of stay was significantly associated with TBSA (P < 0.001). Young children below 10 years seem to be at a higher risk for burn injuries. A significant improvement in burn patients care is observed and practiced and in hospital mortality rate is better compared to neighbouring countries. Preventive programs focusing on safety measures, especially for mothers working in the home, should be implemented urgently to save our children.

Efficacy of moclobemide in burning mouth syndrome: a nonrandomized, open-label study.

PubMed

Pekiner, Filiz Namdar; Gumru, Birsay; Ozbayrak, Semih

2008-01-01

To compare burning mouth syndrome (BMS) patients with age- and gender-matched controls for psychologic conditions, to analyze the effect of menstrual state on the intensity of burning, and to assess the efficacy of an antidepressant medication on the burning pain and psychologic status. Ninety-four patients with BMS and 94 matched control subjects participated in the study. Anxiety and depression were analyzed by means of the Spielberger State-Trait Anxiety Inventory and Zung Self-Rating Depression Scale, and the severity of the burning sensation was measured by means of a visual analog scale (VAS). In female BMS patients and controls, the menstrual state was noted (menstruating, menopausal, or postmenopausal). BMS patients were treated with the antidepressant moclobemide (150 mg 2 times daily) for 3 months. Thereafter, anxiety, depression, and burning pain intensity were reassessed. Patient-perceived satisfactory improvement for burning sensation was assessed using a 5-point categorical rating of change scale. BMS patients had significantly higher anxiety and depression scores than controls (P < .05). After treatment, anxiety and depression scores as well as the VAS values for burning pain decreased significantly (P < .001). Thirty-seven patients reported good to very good improvement, and 44 reported satisfactory improvement. No adverse reactions were reported. The study confirmed earlier reports that BMS patients have higher anxiety and depression levels than controls. An antidepressant medication may be effective in alleviating the burning pain, at least in the short-term.

Burning characteristics and fiber retention of graphite/resin matrix composites

NASA Technical Reports Server (NTRS)

Bowles, K. J.

1980-01-01

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Two types of burning equipment were used. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a Heat Release Rate Calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested and exposed to a thermal radiation. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burning in air.

What determines area burned in large landscapes? Insights from a decade of comparative landscape-fire modelling

Treesearch

Geoffrey J. Cary; Robert E. Keane; Mike D. Flannigan; Ian D. Davies; Russ A. Parsons

2015-01-01

Understanding what determines area burned in large landscapes is critical for informing wildland fire management in fire-prone environments and for representing fire activity in Dynamic Global Vegetation Models. For the past ten years, a group of landscape-fire modellers have been exploring the relative influence of key determinants of area burned in temperate and...

Modeling crop residue burning experiments to evaluate smoke emissions and plume transport

EPA Science Inventory

Crop residue burning is a common land management practice that results in emissions of a variety of pollutants with negative health impacts. Modeling systems are used to estimate air quality impacts of crop residue burning to support retrospective regulatory assessments and also ...

Constraints on CEMP-no progenitors from nuclear astrophysics

NASA Astrophysics Data System (ADS)

Choplin, Arthur; Maeder, André; Meynet, Georges; Chiappini, Cristina

2016-09-01

Context. The CEMP-no stars are long-lived small mass stars presenting a very low iron content and overabundances of carbon with no sign or only very weak signs of s- or r-elements. Although the origin of this abundance pattern is still a matter of debate, it was very likely inherited from a previous massive star, which we call the source star. Aims: We rely on a recent classification of CEMP-no stars arguing that some of them are made of a material processed by hydrogen burning that was enriched in products of helium burning during the nuclear life of the source star. We examine the possibility of forming CEMP-no stars with this material. Methods: We study the nucleosynthesis of the CNO cycle and the Ne-Na Mg-Al chains in a hydrogen burning single zone while injecting the helium burning products 12C, 16O, 22Ne, and 26Mg. We investigate the impact of changing density, temperature and the injection rate. The nuclear reaction rates involving the creation and destruction of 27Al are also examined. Results: 14N, 23Na, 24Mg, and 27Al are formed when injecting 12C, 16O, 22Ne, and 26Mg in the hydrogen burning zone. The 12C/13C ratio is constant under various conditions in the hydrogen burning zone. The predicted [Al/Fe] ratio varies up to ~ 2 dex depending on the prescription used for the reaction rates involving 27Al. Conclusions: The experiments we carried out support the view that some CEMP-no stars are made of a material processed by hydrogen burning that comes from a massive star experiencing mild to strong rotational mixing. During its burning, this material was likely enriched in helium burning products. No material coming from the carbon-oxygen rich core of the source star should be added to form the daughter star, otherwise the 12C/13C ratio would be largely above the observed range of values.

Experimental study on flowing burning behaviors of a pool fire with dripping of melted thermoplastics.

PubMed

Xie, Qiyuan; Tu, Ran; Wang, Nan; Ma, Xin; Jiang, Xi

2014-02-28

The objective of this work is to quantitatively investigate the dripping-burning and flowing fire of thermoplastics. A new experimental setup is developed with a heating vessel and a T-trough. Hot thermoplastic liquids are generated in the vessel by electric heating. N2 gas is continuously injected into the vessel to avoid a sudden ignition of fuel in it. The detailed flowing burning behaviors of pool fire in the T-trough are analyzed through the measurements of the mass, heat flux and temperatures etc. The experimental results suggest that a continuous dripping of melted thermoplastic liquids in a nearly constant mass rate can be successfully made in the new setup. It also shows that the mass dripping rate of melted PS liquid is smaller than PP and PE since its large viscosity. In addition, the flame spread velocities of hot liquids of PS in the T-trough are also smaller than that of PP and PE because of its large viscosity. The mass burning rate of the PP and PE pool fire in T-trough are smaller than PS. Finally, considering the heating, melting, dripping and flowing burning behaviors of these polymers, it is suggested that the fire hazard of PE and PP are obviously higher than PS for their faster flowing burning. Copyright © 2013 Elsevier B.V. All rights reserved.

Modeling of fire smoke movement in multizone garments building using two open source platforms

NASA Astrophysics Data System (ADS)

Khandoker, Md. Arifur Rahman; Galib, Musanna; Islam, Adnan; Rahman, Md. Ashiqur

2017-06-01

Casualty of garment factory workers from factory fire in Bangladesh is a recurring tragedy. Smoke, which is more fatal than fire itself, often propagates through different pathways from lower to upper floors during building fire. Among the toxic gases produced from a building fire, carbon monoxide (CO) can be deadly, even in small amounts. This paper models the propagation and transportation of fire induced smoke (CO) that resulted from the burning of synthetic polyester fibers using two open source platforms, CONTAM and Fire Dynamics Simulator (FDS). Smoke migration in a generic multistoried garment factory building in Bangladesh is modeled using CONTAM where each floor is compartmentalized by different zones. The elevator and stairway shafts are modeled by phantom zones to simulate contaminant (CO) transport from one floor to upper floors. FDS analysis involves burning of two different stacks of polyester jacket of six feet height and with a maximum heat release rate per unit area of 1500kw/m2 over a storage area 50m2 and 150m2, respectively. The resulting CO generation and removal rates from FDS are used in CONTAM to predict fire-borne CO propagation in different zones of the garment building. Findings of the study exhibit that the contaminant flow rate is a strong function of the position of building geometry, location of initiation of fire, amount of burnt material, presence of AHU and contaminant generation and removal rate of CO from the source location etc. The transport of fire-smoke in the building Hallways, stairways and lifts are also investigated in detail to examine the safe egress of the occupants in case of fire.

Chemistry Resolved Kinetic Flow Modeling of TATB Based Explosives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vitello, P A; Fried, L E; Howard, W M

2011-07-21

Detonation waves in insensitive, TATB based explosives are believed to have multi-time scale regimes. The initial burn rate of such explosives has a sub-microsecond time scale. However, significant late-time slow release in energy is believed to occur due to diffusion limited growth of carbon. In the intermediate time scale concentrations of product species likely change from being in equilibrium to being kinetic rate controlled. They use the thermo-chemical code CHEETAH linked to an ALE hydrodynamics code to model detonations. They term their model chemistry resolved kinetic flow as CHEETAH tracks the time dependent concentrations of individual species in the detonationmore » wave and calculates EOS values based on the concentrations. A HE-validation suite of model simulations compared to experiments at ambient, hot, and cold temperatures has been developed. They present here a new rate model and comparison with experimental data.« less

Reasons for Distress Among Burn Survivors at 6, 12, and 24 Months Postdischarge: A Burn Injury Model System Investigation.

PubMed

Wiechman, Shelley A; McMullen, Kara; Carrougher, Gretchen J; Fauerbach, Jame A; Ryan, Colleen M; Herndon, David N; Holavanahalli, Radha; Gibran, Nicole S; Roaten, Kimberly

2017-12-16

To identify important sources of distress among burn survivors at discharge and 6, 12, and 24 months postinjury, and to examine if the distress related to these sources changed over time. Exploratory. Outpatient burn clinics in 4 sites across the country. Participants who met preestablished criteria for having a major burn injury (N=1009) were enrolled in this multisite study. Participants were given a previously developed list of 12 sources of distress among burn survivors and asked to rate on a 10-point Likert-type scale (0=no distress to 10=high distress) how much distress each of the 12 issues was causing them at the time of each follow-up. The Medical Outcomes Study 12-Item Short-Form Health Survey was administered at each time point as a measure of health-related quality of life. The Satisfaction With Appearance Scale was used to understand the relation between sources of distress and body image. Finally, whether a person returned to work was used to determine the effect of sources of distress on returning to employment. It was encouraging that no symptoms were worsening at 2 years. However, financial concerns and long recovery time are 2 of the highest means at all time points. Pain and sleep disturbance had the biggest effect on ability to return to work. These findings can be used to inform burn-specific interventions and to give survivors an understanding of the temporal trajectory for various causes of distress. In particular, it appears that interventions targeted at sleep disturbance and high pain levels can potentially effect distress over financial concerns by allowing a person to return to work more quickly. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

CFD flowfield simulation of Delta Launch Vehicles in a power-on configuration

NASA Technical Reports Server (NTRS)

Pavish, D. L.; Gielda, T. P.; Soni, B. K.; Deese, J. E.; Agarwal, R. K.

1993-01-01

This paper summarizes recent work at McDonnell Douglas Aerospace (MDA) to develop and validate computational fluid dynamic (CFD) simulations of under expanded rocket plume external flowfields for multibody expendable launch vehicles (ELVs). Multi engine reacting gas flowfield predictions of ELV base pressures are needed to define vehicle base drag and base heating rates for sizing external nozzle and base region insulation thicknesses. Previous ELV design programs used expensive multibody power-on wind tunnel tests that employed chamber/nozzle injected high pressure cold or hot-air. Base heating and pressure measurements were belatedly made during the first flights of past ELV's to correct estimates from semi-empirical engineering models or scale model tests. Presently, CFD methods for use in ELV design are being jointly developed at the Space Transportation Division (MDA-STD) and New Aircraft Missiles Division (MDA-NAMD). An explicit three dimensional, zonal, finite-volume, full Navier-Stokes (FNS) solver with finite rate hydrocarbon/air and aluminum combustion kinetics was developed to accurately compute ELV power-on flowfields. Mississippi State University's GENIE++ general purpose interactive grid generation code was chosen to create zonal, finite volume viscous grids. Axisymmetric, time dependent, turbulent CFD simulations of a Delta DSV-2A vehicle with a MB-3 liquid main engine burning RJ-1/LOX were first completed. Hydrocarbon chemical kinetics and a k-epsilon turbulence model were employed and predictions were validated with flight measurements of base pressure and temperature. Zonal internal/external grids were created for a Delta DSV-2C vehicle with a MB-3 and three Castor-1 solid motors burning and a Delta-2 with an RS-27 main engine (LOX/RP-1) and 9 GEM's attached/6 burning. Cold air, time dependent FNS calculations were performed for DSV-2C during 1992. Single phase simulations that employ finite rate hydrocarbon and aluminum (solid fuel) combustion chemistry are currently in progress. Reliable and efficient Eulerian algorithms are needed to model two phase (solid-gas) momentum and energy transfer mechanisms for solid motor fuel combustion products.

CFD flowfield simulation of Delta Launch Vehicles in a power-on configuration

NASA Astrophysics Data System (ADS)

Pavish, D. L.; Gielda, T. P.; Soni, B. K.; Deese, J. E.; Agarwal, R. K.

1993-07-01

This paper summarizes recent work at McDonnell Douglas Aerospace (MDA) to develop and validate computational fluid dynamic (CFD) simulations of under expanded rocket plume external flowfields for multibody expendable launch vehicles (ELVs). Multi engine reacting gas flowfield predictions of ELV base pressures are needed to define vehicle base drag and base heating rates for sizing external nozzle and base region insulation thicknesses. Previous ELV design programs used expensive multibody power-on wind tunnel tests that employed chamber/nozzle injected high pressure cold or hot-air. Base heating and pressure measurements were belatedly made during the first flights of past ELV's to correct estimates from semi-empirical engineering models or scale model tests. Presently, CFD methods for use in ELV design are being jointly developed at the Space Transportation Division (MDA-STD) and New Aircraft Missiles Division (MDA-NAMD). An explicit three dimensional, zonal, finite-volume, full Navier-Stokes (FNS) solver with finite rate hydrocarbon/air and aluminum combustion kinetics was developed to accurately compute ELV power-on flowfields. Mississippi State University's GENIE++ general purpose interactive grid generation code was chosen to create zonal, finite volume viscous grids. Axisymmetric, time dependent, turbulent CFD simulations of a Delta DSV-2A vehicle with a MB-3 liquid main engine burning RJ-1/LOX were first completed. Hydrocarbon chemical kinetics and a k-epsilon turbulence model were employed and predictions were validated with flight measurements of base pressure and temperature. Zonal internal/external grids were created for a Delta DSV-2C vehicle with a MB-3 and three Castor-1 solid motors burning and a Delta-2 with an RS-27 main engine (LOX/RP-1) and 9 GEM's attached/6 burning. Cold air, time dependent FNS calculations were performed for DSV-2C during 1992. Single phase simulations that employ finite rate hydrocarbon and aluminum (solid fuel) combustion chemistry are currently in progress. Reliable and efficient Eulerian algorithms are needed to model two phase (solid-gas) momentum and energy transfer mechanisms for solid motor fuel combustion products.

Empirical models to predict the volumes of debris flows generated by recently burned basins in the western U.S.

USGS Publications Warehouse

Gartner, J.E.; Cannon, S.H.; Santi, P.M.; deWolfe, V.G.

2008-01-01

Recently burned basins frequently produce debris flows in response to moderate-to-severe rainfall. Post-fire hazard assessments of debris flows are most useful when they predict the volume of material that may flow out of a burned basin. This study develops a set of empirically-based models that predict potential volumes of wildfire-related debris flows in different regions and geologic settings. The models were developed using data from 53 recently burned basins in Colorado, Utah and California. The volumes of debris flows in these basins were determined by either measuring the volume of material eroded from the channels, or by estimating the amount of material removed from debris retention basins. For each basin, independent variables thought to affect the volume of the debris flow were determined. These variables include measures of basin morphology, basin areas burned at different severities, soil material properties, rock type, and rainfall amounts and intensities for storms triggering debris flows. Using these data, multiple regression analyses were used to create separate predictive models for volumes of debris flows generated by burned basins in six separate regions or settings, including the western U.S., southern California, the Rocky Mountain region, and basins underlain by sedimentary, metamorphic and granitic rocks. An evaluation of these models indicated that the best model (the Western U.S. model) explains 83% of the variability in the volumes of the debris flows, and includes variables that describe the basin area with slopes greater than or equal to 30%, the basin area burned at moderate and high severity, and total storm rainfall. This model was independently validated by comparing volumes of debris flows reported in the literature, to volumes estimated using the model. Eighty-seven percent of the reported volumes were within two residual standard errors of the volumes predicted using the model. This model is an improvement over previous models in that it includes a measure of burn severity and an estimate of modeling errors. The application of this model, in conjunction with models for the probability of debris flows, will enable more complete and rapid assessments of debris flow hazards following wildfire.

Cooling of burns: Mechanisms and models.

PubMed

Wright, E H; Harris, A L; Furniss, D

2015-08-01

The role of cooling in the acute management of burns is widely accepted in clinical practice, and is a cornerstone of basic first aid in burns. This has been underlined in a number of animal models. The mechanism by which it delivers its benefit is poorly understood, but there is a reduction in burns progression over the first 48 h, reduced healing time, and some subjective improvements in scarring when cooling is administered after burning. Intradermal temperature normalises within a matter of seconds to a few minutes, yet the benefits of even delayed cooling persist, implying it is not simply the removal of thermal energy from the damaged tissues. Animal models have used oedema formation, preservation of dermal perfusion, healing time and hair retention as indicators of burns severity, and have shown cooling to improve these indices, but pharmacological or immunological blockade of humoural and cellular mediators of inflammation did not reproduce the benefit of cooling. More recently, some studies of tissue from human and animal burns have shown consistent, reproducible, temporal changes in gene expression in burned tissues. Here, we review the experimental evidence of the role and mechanism of cooling in burns management, and suggest future research directions that may eventually lead to improved treatment outcomes. Copyright © 2015. Published by Elsevier Ltd.

Comparison of mortality prediction models in burns ICU patients in Pinderfields Hospital over 3 years.

PubMed

Douglas, Helen E; Ratcliffe, Andrew; Sandhu, Rajdeep; Anwar, Umair

2015-02-01

Many different burns mortality prediction models exist; however most agree that important factors that can be weighted include the age of the patient, the total percentage of body surface area burned and the presence or absence of smoke inhalation. A retrospective review of all burns primarily admitted to Pinderfields Burns ICU under joint care of burns surgeons and intensivists for the past 3 years was completed. Predicted mortality was calculated using the revised Baux score (2010), the Belgian Outcome in Burn Injury score (2009) and the Boston group score by Ryan et al. (1998). Additionally 28 of the 48 patients had APACHE II scores recorded on admission and the predicted and actual mortality of this group were compared. The Belgian score had the highest sensitivity and negative predictive value (72%/85%); followed by the Boston score (66%/78%) and then the revised Baux score (53%/70%). APACHE II scores had higher sensitivity (81%) and NPV (92%) than any of the burns scores. In our group of burns ICU patients the Belgian model was the most sensitive and specific predictor of mortality. In our subgroup of patients with APACHE II data, this score more accurately predicted survival and mortality. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Study of Burn Scar Extraction Automatically Based on Level Set Method using Remote Sensing Data

PubMed Central

Liu, Yang; Dai, Qin; Liu, JianBo; Liu, ShiBin; Yang, Jin

2014-01-01

Burn scar extraction using remote sensing data is an efficient way to precisely evaluate burn area and measure vegetation recovery. Traditional burn scar extraction methodologies have no well effect on burn scar image with blurred and irregular edges. To address these issues, this paper proposes an automatic method to extract burn scar based on Level Set Method (LSM). This method utilizes the advantages of the different features in remote sensing images, as well as considers the practical needs of extracting the burn scar rapidly and automatically. This approach integrates Change Vector Analysis (CVA), Normalized Difference Vegetation Index (NDVI) and the Normalized Burn Ratio (NBR) to obtain difference image and modifies conventional Level Set Method Chan-Vese (C-V) model with a new initial curve which results from a binary image applying K-means method on fitting errors of two near-infrared band images. Landsat 5 TM and Landsat 8 OLI data sets are used to validate the proposed method. Comparison with conventional C-V model, OSTU algorithm, Fuzzy C-mean (FCM) algorithm are made to show that the proposed approach can extract the outline curve of fire burn scar effectively and exactly. The method has higher extraction accuracy and less algorithm complexity than that of the conventional C-V model. PMID:24503563

High-Pressure Burning Rate Studies of Solid Rocket Propellants

DTIC Science & Technology

2013-01-01

monopropellant burning rate. The self-de§agration rates of neat AP are plotted in Fig. 2 for both pressed pellets and single crystals. There is agreement...rate data from various investigators: 1 ¡ [2]; pressed pellets : 2 ¡ [3], 3 ¡ [4], and 4 ¡ [2]; and single crystals: 5 ¡ [5], and 6 ¡ [6]. Line ¡ AP...7]. Strand or window burners have had more use in the solid propellant community. There are numerous types and styles of combustion vessels, but they

Which evolutionary status does the Blue Large-Amplitude Pulsators stay at?

NASA Astrophysics Data System (ADS)

Wu, Tao; Li, Yan

2018-05-01

Asteroseismology is a very useful tool for exploring the stellar interiors and evolutionary status and for determining stellar fundamental parameters, such as stellar mass, radius, surface gravity, and the stellar mean density. In the present work, we use it to preliminarily analyze the 14 new-type pulsating stars: Blue Large-Amplitude Pulsators (BLAPs) which is observed by OGLE project, to roughly analyze their evolutionary status. We adopt the theory of single star evolution and artificially set the mass loss rate of \\dot{M}=-2× 10^{-4} M_{⊙}/year and mass loss beginning at the radius of R = 40 R_{⊙} on red giant branch to generate a series of theoretical models. Based on these theoretical models and the corresponding observations, we find that those BLAP stars are more likely to be the core helium burning stars. Most of them are in the middle and late phase of the helium burning.

Effect of propellant deformation on ignition and combustion processes in solid propellant cracks

NASA Technical Reports Server (NTRS)

Kumar, M.; Kuo, K. K.

1980-01-01

A comprehensive theoretical model was formulated to study the development of convective burning in a solid propellant crack which continually deforms due to burning and pressure loading. In the theoretical model, the effect of interrelated structural deformation and combustion processes was taken into account by considering (1) transient, one dimensional mass, momentum, and energy conservation equations in the gas phase; (2) a transient, one dimensional heat conduction equation in the solid phase; and (3) quasi-static deformation of the two dimensional, linear viscoelastic propellant crack caused by pressure loading. Partial closures may generate substantial local pressure peaks along the crack, implying a strong coupling between chamber pressurization, crack combustion, and propellant deformation, especially when the cracks are narrow and the chamber pressurization rates high. The maximum pressure in the crack cavity is generally higher than that in the chamber. The initial flame-spreading process is not affected by propellant deformation.

Should early amputation impact initial fluid therapy algorithms in burns resuscitation? A retrospective analysis using 3D modelling.

PubMed

Staruch, Robert M T; Beverly, A; Lewis, D; Wilson, Y; Martin, N

2017-02-01

While the epidemiology of amputations in patients with burns has been investigated previously, the effect of an amputation on burn size and its impact on fluid management have not been considered in the literature. Fluid resuscitation volumes are based on the percentage of the total body surface area (%TBSA) burned calculated during the primary survey. There is currently no consensus as to whether the fluid volumes should be recalculated after an amputation to compensate for the new body surface area. The aim of this study was to model the impact of an amputation on burn size and predicted fluid requirement. A retrospective search was performed of the database at the Queen Elizabeth Hospital Birmingham Regional Burns Centre to identify all patients who had required an early amputation as a result of their burn injury. The search identified 10 patients over a 3-year period. Burn injuries were then mapped using 3D modelling software. BurnCase3D is a computer program that allows accurate plotting of burn injuries on a digital mannequin adjusted for height and weight. Theoretical fluid requirements were then calculated using the Parkland formula for the first 24 h, and Herndon formula for the second 24 h, taking into consideration the effects of the amputation on residual burn size. This study demonstrated that amputation can have an unpredictable effect on burn size that results in a significant deviation from predicted fluid resuscitation volumes. This discrepancy in fluid estimation may cause iatrogenic complications due to over-resuscitation in burn-injured casualties. Combining a more accurate estimation of postamputation burn size with goal-directed fluid therapy during the resuscitation phase should enable burn care teams to optimise patient outcomes. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Cool-flame Extinction During N-Alkane Droplet Combustion in Microgravity

NASA Technical Reports Server (NTRS)

Nayagam, Vedha; Dietrich, Daniel L.; Hicks, Michael C.; Williams, Forman A.

2014-01-01

Recent droplet combustion experiments onboard the International Space Station (ISS) have revealed that large n-alkane droplets can continue to burn quasi-steadily following radiative extinction in a low-temperature regime, characterized by negative-temperaturecoefficient (NTC) chemistry. In this study we report experimental observations of n-heptane, n-octane, and n-decane droplets of varying initial sizes burning in oxygen/nitrogen/carbon dioxide and oxygen/helium/nitrogen environments at 1.0, 0.7, and 0.5 atmospheric pressures. The oxygen concentration in these tests varied in the range of 14% to 25% by volume. Large n-alkane droplets exhibited quasi-steady low-temperature burning and extinction following radiative extinction of the visible flame while smaller droplets burned to completion or disruptively extinguished. A vapor-cloud formed in most cases slightly prior to or following the "cool flame" extinction. Results for droplet burning rates in both the hot-flame and cool-flame regimes as well as droplet extinction diameters at the end of each stage are presented. Time histories of radiant emission from the droplet captured using broadband radiometers are also presented. Remarkably the "cool flame" extinction diameters for all the three n-alkanes follow a trend reminiscent of the ignition delay times observed in previous studies. The similarities and differences among the n-alkanes during "cool flame" combustion are discussed using simplified theoretical models of the phenomenon

Soil properties and root biomass responses to prescribed burning in young Corsican pine (Pinus nigra Arn.) stands.

PubMed

Tufekcioglu, Aydin; Kucuk, Mehmet; Saglam, Bulent; Bilgili, Ertugrul; Altun, Lokman

2010-05-01

Fire is an important tool in the management of forest ecosystems. Although both prescribed and wildland fires are common in Turkey, few studies have addressed the influence of such disturbances on soil properties and root biomass dynamics. In this study, soil properties and root biomass responses to prescribed fire were investigated in 25-year-old corsican pine (Pinus nigra Arn.) stands in Kastamonu, Turkey. The stands were established by planting and were subjected to prescribed burning in July 2003. Soil respiration rates were determined every two months using soda-lime method over a two-year period. Fine (0-2 mm diameter) and small root (2-5 mm diameter) biomass were sampled approximately bimonthly using sequential coring method. Mean daily soil respiration ranged from 0.65 to 2.19 g Cm(-2) d(-1) among all sites. Soil respiration rates were significantly higher in burned sites than in controls. Soil respiration rates were correlated significantly with soil moisture and soil temperature. Fine root biomass was significantly lower in burned sites than in control sites. Mean fine root biomass values were 4940 kg ha(-1) for burned and 5450 kg ha(-1) for control sites. Soil pH was significantly higher in burned sites than in control sites in 15-35 cm soil depth. Soil organic matter content did not differ significantly between control and burned sites. Our results indicate that, depending on site conditions, fire could be used successfully as a tool in the management of forest stands in the study area.

Lessons from the fires of 2000: Post-fire heterogeneity in ponderosa pine forests

USGS Publications Warehouse

Kotliar, Natasha B.; Haire, Sandra L.; Key, Carl H.; Omni, Phillip N.; Joyce, Linda A.

2003-01-01

We evaluate burn-severity patterns for six burns that occurred in the southern Rocky Mountains and the Colorado Plateau in 2000. We compare the results of two data sources: Burned Area Rehabilitations Teams (BAER) and a spatial burnseverity model derived from satellite imagery (the Normalized Burn Ratio; NBR). BAER maps tended to overestimate area of severe burns and underestimate area of moderate-severity burns relative to NBR maps. Low elevation and more southern ponderosa pine burns were predominantly understory burns, whereas burns at higher elevations and farther north had a greater component of high-severity burns. Thus, much, if not most, of the area covered by these burns appears to be consistent with historic burns and contributes to healthy functioning ecosystems.

Photoinduced electron transfer and persistent spectral hole-burning in natural emerald.

PubMed

Riesen, Hans

2011-06-02

Wavelength-selective excited-state lifetime measurements and absorption, luminescence, and hole-burning spectra of a natural African emerald crystal are reported. The (2)E excited-state lifetime displays an extreme wavelength dependence, varying from 190 to 37 μs within 1.8 nm of the R(1)-line. Overall, the excited state is strongly quenched, in comparison to laboratory-created emerald (τ=1.3 ms), with an average quenching rate of ∼6 × 10(3) s(-1) at 2.5 K. This quenching is attributed to photoinduced electron transfer caused by a relatively high concentration of Fe(2+) ions. The forward electron-transfer rate, k(f), from the nearest possible Fe(2+) sites at around 5 Å is estimated to be ∼20 × 10(3) s(-1) at 2.5 K. The photoreductive quenching of the excited Cr(3+) ions by Fe(2+) is followed by rapid electron back-transfer in the ground state upon deactivation. The exchange interaction based quenching can be modeled by assuming a random quencher distribution within the possible Fe(2+) sites with the forward electron-transfer rate, k(f), given as a function of acceptor-donor separation R by exp[(R(f)-R)/a(f)]; R(f) and a(f) values of 13.5 and 2.7 Å are obtained at 2.5 K. The electron transfer/back-transfer reorganizes the local crystal lattice, occasionally leading to a minor variation of the short-range structure around the Cr(3+) ions. This provides a mechanism for spectral hole-burning for which a moderately high quantum efficiency of about ∼0.005% is observed. Spectral holes are subject to spontaneous hole-filling and spectral diffusion, and both effects can be quantified within the standard two-level systems for non-photochemical hole-burning. Importantly, the absorbance increases on both sides of broad spectral holes, and isosbestic points are observed, in accord with the expected distribution of the "photoproduct" in a non-photochemical hole-burning process. © 2011 American Chemical Society

Plasma L-5-oxoproline kinetics and whole blood glutathione synthesis rates in severely burned adult humans.

PubMed

Yu, Yong-Ming; Ryan, Colleen M; Fei, Zhe-Wei; Lu, Xiao-Ming; Castillo, Leticia; Schultz, John T; Tompkins, Ronald G; Young, Vernon R

2002-02-01

Compromised glutathione homeostasis is associated with increased morbidity in various disease states. We evaluated the kinetics of L-5-oxoproline, an intermediate in the gamma-glutamyl cycle of glutathione production, in fourteen severely burned adults by use of a primed, constant intravenous infusion of L-5-[1-(13)C]oxoproline. In nine of these patients, whole blood glutathione synthesis and plasma kinetics of glycine and leucine were also measured with [(15)N]glycine and L-[(2)H(3)]leucine tracers. Patients were studied under a "basal" condition that provided a low dose of glucose and total parenteral nutrition. For comparison with control subjects, whole blood glutathione synthesis was estimated in six healthy adults. Burn patients in a basal condition showed significantly higher rates of plasma oxoproline clearance and urinary D- and L-oxoproline excretion compared with fasting healthy control subjects. Whole blood glutathione concentration and absolute synthesis rate in the basal state were lower than for control subjects. Total parenteral feeding without cysteine but with generous methionine did not affect oxoproline kinetics or whole blood glutathione synthesis. The estimated rate of glycine de novo synthesis was also lower in burn patients, suggesting a possible change in glycine availability for glutathione synthesis. The roles of precursor amino acid availability, as well as alterations in metabolic capacity, in modulating whole blood glutathione production in burns now require investigation.

Cigarette ignition of soft furnishings: A literature review with commentary

NASA Astrophysics Data System (ADS)

Krasny, John F.

1987-04-01

Literature pertinent to the ignition by smoldering cigarettes of upholstered furniture and mattresses (soft furnishings) was searched through early 1986. This included literature on the smoldering behavior of cigarettes in air; their behavior on a variety of substrates simulating soft furnishings; mechanism of smoldering in substrates; relative cigarette ignition resistance of substrates; and relative propensity of commercial cigarette packings to ignite substrates. According to the reviewed literature, the smoldering behavior of cigarettes on substrates differs from that of cigarettes burning in air: on substrates, cigarette temperatures tend to be lower, and burning rates slower. These differences seem to be larger for substrates which ignite than for those which self-extinguish after the cigarette burns out. The characteristics of soft furnishings which insure resistance to cigarette ignition have been established, but those of cigarettes with low propensity to ignite furnishings have not. No mathematical model has been reported for the interaction of cigarette and substrate, but some empirical data do exist.

Fuel droplet burning rates at high pressures

NASA Technical Reports Server (NTRS)

Canada, G. S.; Faeth, G. M.

1972-01-01

Combustion of methanol, ethanol, propanol -1, n - pentane, n - heptane and n - decane was observed in air under natural convection conditions at pressures up to 100 atm. The droplets were simulated by porous spheres with diameters in the range 0.63 - 1.90 cm. The pressure levels of the tests were high enough so that near critical combustion was observed for methanol and ethanol. Measurements were made of the burning rate and liquid surface temperatures of the fuels. The data were compared with variable property analysis of the combustion process, including a correction for natural convection. The burning rate predictions of the various theories were similar and in fair agreement with the data. The high pressure theory gave the best prediction for the liquid surface temperatures of ethanol and propanol -1 at high pressure. The experiments indicated the approach of critical burning conditions for methanol and ethanol at pressures on the order of 80 - 100 atm, which was in good agreement with the predictions of both the low and high pressure analysis.

The role and importance of porosity in the deflagration rates of HMX-based materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Hsu, P C; Springer, H K

The deflagration behavior of thermally damaged HMX-based materials will be discussed. Strands of material were burned at pressures ranging from 10-300 MPa using the LLNL high pressure strand burner. Strands were heated in-situ and burned while still hot; temperatures range from 90-200 C and were chosen in order to allow for thermal damage of the material without significant decomposition of the HMX. The results indicate that multiple variables affect the burn rate but the most important are the polymorph of HMX and the nature and thermal stability of the non-HE portion of the material. Characterization of the strands indicate thatmore » the thermal soak produces significant porosity and permeability in the sample allowing for significantly faster burning due to the increased surface area and new pathways for flame spread into the material. Specifically, the deflagration rates of heated PBXN-9, LX-10, and PBX-9501 will be discussed and compared.« less

[Changes of soil nutrient contents after prescribed burning of forestland in Heshan City, Guangdong Province].

PubMed

Sun, Yu-xin; Wu, Jian-ping; Zhou, Li-xia; Lin, Yong-biao; Fu, Sheng-lei

2009-03-01

A comparative study was conducted to analyze the changes of soil nutrient contents in Eucalyptus forestland and in shrubland after three years of prescribed burning. In Eucalyptus forestland, soil organic carbon, total nitrogen, available potassium contents and soil pH decreased significantly; soil available phosphorus and exchangeable magnesium contents, net nitrogen mineralization rate and ammonification rate also decreased but showed no significant difference. In shrubland, soil exchangeable calcium content increased significantly, but the contents of other nutrients had no significant change. The main reason of the lower soil net nitrogen mineralization rate in Eucalyptus forest could be the decrease of available substrates and the uptake of larger amount of soil nutrients by the fast growth of Eucalyptus. The soil nutrients in shrubland had a quick restoration rate after burning.

Regional Changes in Charcoal-Burning Suicide Rates in East/Southeast Asia from 1995 to 2011: A Time Trend Analysis

PubMed Central

Chang, Shu-Sen; Chen, Ying-Yeh; Yip, Paul S. F.; Lee, Won Jin; Hagihara, Akihito; Gunnell, David

2014-01-01

Background Suicides by carbon monoxide poisoning resulting from burning barbecue charcoal reached epidemic levels in Hong Kong and Taiwan within 5 y of the first reported cases in the early 2000s. The objectives of this analysis were to investigate (i) time trends and regional patterns of charcoal-burning suicide throughout East/Southeast Asia during the time period 1995–2011 and (ii) whether any rises in use of this method were associated with increases in overall suicide rates. Sex- and age-specific trends over time were also examined to identify the demographic groups showing the greatest increases in charcoal-burning suicide rates across different countries. Methods and Findings We used data on suicides by gases other than domestic gas for Hong Kong, Japan, the Republic of Korea, Taiwan, and Singapore in the years 1995/1996–2011. Similar data for Malaysia, the Philippines, and Thailand were also extracted but were incomplete. Graphical and joinpoint regression analyses were used to examine time trends in suicide, and negative binomial regression analysis to study sex- and age-specific patterns. In 1995/1996, charcoal-burning suicides accounted for <1% of all suicides in all study countries, except in Japan (5%), but they increased to account for 13%, 24%, 10%, 7%, and 5% of all suicides in Hong Kong, Taiwan, Japan, the Republic of Korea, and Singapore, respectively, in 2011. Rises were first seen in Hong Kong after 1998 (95% CI 1997–1999), followed by Singapore in 1999 (95% CI 1998–2001), Taiwan in 2000 (95% CI 1999–2001), Japan in 2002 (95% CI 1999–2003), and the Republic of Korea in 2007 (95% CI 2006–2008). No marked increases were seen in Malaysia, the Philippines, or Thailand. There was some evidence that charcoal-burning suicides were associated with an increase in overall suicide rates in Hong Kong, Taiwan, and Japan (for females), but not in Japan (for males), the Republic of Korea, and Singapore. Rates of change in charcoal-burning suicide rate did not differ by sex/age group in Taiwan and Hong Kong but appeared to be greatest in people aged 15–24 y in Japan and people aged 25–64 y in the Republic of Korea. The lack of specific codes for charcoal-burning suicide in the International Classification of Diseases and variations in coding practice in different countries are potential limitations of this study. Conclusions Charcoal-burning suicides increased markedly in some East/Southeast Asian countries (Hong Kong, Taiwan, Japan, the Republic of Korea, and Singapore) in the first decade of the 21st century, but such rises were not experienced by all countries in the region. In countries with a rise in charcoal-burning suicide rates, the timing, scale, and sex/age pattern of increases varied by country. Factors underlying these variations require further investigation, but may include differences in culture or in media portrayals of the method. Please see later in the article for the Editors' Summary PMID:24691071

40 CFR Table 24 to Subpart Uuu of... - Continuous Monitoring Systems for Inorganic HAP Emissions From Catalytic Reforming Units

Code of Federal Regulations, 2011 CFR

2011-07-01

... entering the scrubber during coke burn-off and catalyst rejuvenation; and continuous parameter monitoring system to measure and record gas flow rate entering or exiting the scrubber during coke burn-off and... alkalinity of the water (or scrubbing liquid) exiting the scrubber during coke burn-off and catalyst...

Properties of Deflagration Fronts and Models for Type IA Supernovae

NASA Astrophysics Data System (ADS)

Domínguez, I.; Höflich, P.

2000-01-01

Detailed models of the explosion of a white dwarf that include self-consistent calculations of the light curve and spectra provide a link between observational quantities and the underlying explosion model. These calculations assume spherical geometry and are based on parameterized descriptions of the burning front. Recently, the first multidimensional calculations for nuclear burning fronts have been performed. Although a fully consistent treatment of the burning fronts is beyond the current state of the art, these calculations provide a new and better understanding of the physics. Several new descriptions for flame propagation have been proposed by Khokhlov et al. and Niemeyer et al. Using various descriptions for the propagation of a nuclear deflagration front, we have studied the influence on the results of previous analyses of Type Ia supernovae, namely, the nucleosynthesis and structure of the expanding envelope. Our calculations are based on a set of delayed detonation models with parameters that give a good account of the optical and infrared light curves and of the spectral evolution. In this scenario, the burning front first propagates in a deflagration mode and subsequently turns into a detonation. The explosions and light curves are calculated using a one-dimensional Lagrangian radiation-hydro code including a detailed nuclear network. We find that the results of the explosion are rather insensitive to details of the description of the deflagration front, even if its speed and the time from the transition to detonation differ almost by a factor of 2. For a given white dwarf (WD) and a fixed transition density, the total production of elements changes by less than 10%, and the distribution in the velocity space changes by less than 7%. Qualitatively, this insensitivity of the final outcome of the explosion to the details of the flame propagation during the (slow) deflagration phase can be understood as follows: for plausible variations in the speed of the turbulent deflagration, the duration of this phase is several times longer than the sound crossing time in the initial WD. Therefore, the energy produced during the early nuclear burning can be redistributed over the entire WD, causing a slow preexpansion. In this intermediate state, the WD is still bound but its binding energy is reduced by the amount of nuclear energy. The expansion ratio depends mainly on the total amount of burning during the deflagration phase. Consequently, the conditions are very similar under which nuclear burning takes place during the subsequent detonation phase. In our example, the density and temperature at the burning front changes by less than 3%, and the expansion velocity changes by less than 10%. The burning conditions are very close to previous calculations which used a constant deflagration velocity. Based on a comparison with observations, those required low deflagration speeds (~2%-3% of the speed of sound). Exceptions to the similarity are the innermost layers of ~0.03-0.05 Msolar. Still, nuclear burning is in nuclear statistical equilibrium, but the rate of electron capture is larger for the new descriptions of the flame propagation. Consequently, the production of very neutron-rich isotopes is increased. In our example, close to the center Ye is about 0.44, compared to 0.46 in the model with constant deflagration speed. This increases the 48Ca production by more than a factor of 100 to 3.E-6 Msolar. Conclusions from previous analyses of light curves and spectra on the properties of the WD and the explosions will not change, and even with the new descriptions, the delayed detonation scenario is consistent with the observations. Namely, the central density results with respect to the chemical structure of the progenitor and the transition density from deflagration to detonation do not change. The reason for this similarity is the fact that the total amount of burning during the long deflagration phase determines the restructuring of the WD prior to the detonation. Therefore, we do not expect that the precise, microphysical prescription for the speed of a subsonic burning front has a significant effect on the outcome. However, at the current level of uncertainties for the burning front, the relation between properties of the burning front and of the initial white dwarf cannot be obtained from a comparison between observation and theoretical predictions by one-dimensional models. Multidimensional calculations are needed (1) to get inside the relations between model parameters such as central density and properties of the deflagration front and its relation to the transition density between deflagration and detonation and (2) to make use of information on asphericity that is provided by polarization measurements. These questions are essential to test, estimate, and predict some of the evolutionary effects of SNe Ia and their use as cosmological yardsticks.

Relative importance of fuel management, ignition management and weather for area burned: Evidence from five landscape-fire-succession models

Treesearch

Geoffrey J. Cary; Mike D. Flannigan; Robert E. Keane; Ross A. Bradstock; Ian D. Davies; James M. Lenihan; Chao Li; Kimberley A. Logan; Russell A. Parsons

2009-01-01

The behaviour of five landscape fire models (CAFE, FIRESCAPE, LAMOS(HS), LANDSUM and SEMLAND) was compared in a standardised modelling experiment. The importance of fuel management approach, fuel management effort, ignition management effort and weather in determining variation in area burned and number of edge pixels burned (a measure of potential impact on assets...

Infiltration and interrill erosion rates after a wildfire in western Montana, USA

USDA-ARS?s Scientific Manuscript database

The 2000 Valley Complex wildfire burned in steep montane forests with ash cap soils in western Montana, USA. The effects of high burn severity on forest soil hydrologic function was examined using rainfall simulations (100 mm h-1 for 1 h) on 0.5-m2 plots. Infiltration rates and sediment yields and c...

Reaction rate for carbon burning in massive stars

DOE PAGES

Jiang, C. L.; Santiago-Gonzalez, D.; Almaraz-Calderon, S.; ...

2018-01-10

Carbon burning is a critical phase for nucleosynthesis in massive stars. The conditions for igniting this burning stage, and the subsequent isotope composition of the resulting ashes, depend strongly on the reaction rate for 12C+ 12C fusion at very low energies. Results for the cross sections for this reaction are influenced by various backgrounds encountered in measurements at such energies. In this paper, we report on a new measurement of 12C+ 12C fusion cross sections where these backgrounds have been minimized. In conclusion, it is found that the astrophysical S factor exhibits a maximum around E cm=3.5–4.0 MeV, which leadsmore » to a reduction of the previously predicted astrophysical reaction rate.« less

High-pressure and stark hole-burning studies of chlorosome antennas from Chlorobium tepidum.

PubMed

Wu, H M; Rätsep, M; Young, C S; Jankowiak, R; Blankenship, R E; Small, G J

2000-09-01

Results from high-pressure and Stark hole-burning experiments on isolated chlorosomes from the green sulfur bacterium Chlorobium tepidum are presented, as well as Stark hole-burning data for bacteriochlorophyll c (BChl c) monomers in a poly(vinyl butyral) copolymer film. Large linear pressure shift rates of -0.44 and -0.54 cm(-1)/MPa were observed for the chlorosome BChl c Q(y)-band at 100 K and the lowest Q(y)-exciton level at 12 K, respectively. It is argued that approximately half of the latter shift rate is due to electron exchange coupling between BChl c molecules. The similarity between the above shift rates and those observed for the B875 and B850 BChl a rings of the light-harvesting complexes of purple bacteria is emphasized. For BChl c monomer, fDeltamu++ = 0.35 D, where Deltamu+ is the dipole moment change for the Q(y) transition and f is the local field correction factor. The data establish that Deltamu+ is dominated by the matrix-induced contribution. The change in polarizability (Deltaalpha) for the Q(y) transition of the BChl c monomer is estimated at 19 A(3), which is essentially identical to that of the Chl a monomer. Interestingly, no Stark effects were observed for the lowest exciton level of the chlorosomes (maximum Stark field of 10(5) V/cm). Possible explanations for this are given, and these include consideration of structural models for the chlorosome BChl c aggregates.

A small single-nozzle rainfall simulator to measure erosion response on different burn severities in southern British Columbia, Canada

NASA Astrophysics Data System (ADS)

Covert, Ashley; Jordan, Peter

2010-05-01

To study the effects of wildfire burn severity on runoff generation and soil erosion from high intensity rainfall, we constructed an effective yet simple rainfall simulator that was inexpensive, portable and easily operated by two people on steep, forested slopes in southern British Columbia, Canada. The entire apparatus, including simulator, pumps, hoses, collapsible water bladders and sample bottles, was designed to fit into a single full-sized pick-up truck. The three-legged simulator extended to approximately 3.3 metres above ground on steep slopes and used a single Spraying Systems 1/2HH-30WSQ nozzle which can easily be interchanged for other sized nozzles. Rainfall characteristics were measured using a digital camera which took images of the raindrops against a grid. Median drop size and velocity 5 cm above ground were measured and found to be 3/4 of the size of natural rain drops of that diameter class, and fell 7% faster than terminal velocity. The simulator was used for experiments on runoff and erosion on sites burned in 2007 by two wildfires in southern British Columbia. Simulations were repeated one and two years after the fires. Rainfall was simulated at an average rate of 67 mm hr-1 over a 1 m2 plot for 20 minutes. This rainfall rate is similar to the 100 year return period rainfall intensity for this duration at a nearby weather station. Simulations were conducted on five replicate 1 m2 plots in each experimental unit including high burn severity, moderate burn severity, unburned, and unburned with forest floor removed. During the simulation a sample was collected for 30 seconds every minute, with two additional samples until runoff ceased, resulting in 22 samples per simulation. Runoff, overland flow coefficient, infiltration and sediment yield were compared between treatments. Additional simulations were conducted immediately after a 2009 wildfire to test different mulch treatments. Typical results showed that runoff on plots with high burn severity and with forest floor removed was similar, reaching on average a steady rate of about 60% of rainfall rate after about 7 minutes. Runoff on unburned plots with intact forest floor was much lower, typically less than 20% of rainfall rate. Sediment yield was greatest on plots with forest floor removed, followed by severely burned plots. Sediment yield on unburned and moderately burned plots was very low to zero. These results are consistent with qualitative observations made following several extreme rainfall events on recent burns in the region.

Near Surface Vapor Bubble Layers in Buoyant Low Stretch Burning of Polymethylmethacrylate

NASA Technical Reports Server (NTRS)

Olson, Sandra L.; Tien, J. S.

1999-01-01

Large-scale buoyant low stretch stagnation point diffusion flames over solid fuel (polymethylmethacrylate) were studied for a range of aerodynamic stretch rates of 2-12/ sec which are of the same order as spacecraft ventilation-induced stretch in a microgravity environment. An extensive layer of polymer material above the glass transition temperature is observed. Unique phenomena associated with this extensive glass layer included substantial swelling of the burning surface, in-depth bubble formation, and migration and/or elongation of the bubbles normal to the hot surface. The bubble layer acted to insulate the polymer surface by reducing the effective conductivity of the solid. The reduced in-depth conduction stabilized the flame for longer than expected from theory neglecting the bubble layer. While buoyancy acts to move the bubbles deeper into the molten polymer, thermocapillary forces and surface regression both act to bring the bubbles to the burning surface. Bubble layers may thus be very important in low gravity (low stretch) burning of materials. As bubbles reached the burning surface, monomer fuel vapors jetted from the surface, enhancing burning by entraining ambient air flow. Popping of these bubbles at the surface can expel burning droplets of the molten material, which may increase the fire propagation hazards at low stretch rates.

Paediatric electrical burn injuries: experience from a tertiary care burns unit in North India

PubMed Central

Srivastava, S.; Patil, A.N.; Bedi, M.; Tawar, R.S.

2017-01-01

Summary Electrical burn injuries in the paediatric age group constitute a small proportion of all burn cases and cause significant morbidity and long-term psychosocial impact. The objective of this study was to evaluate various aspects of electrical burn injuries in the paediatric age group in our region. A retrospective review was done of all paediatric electrical burns admitted to a tertiary care burns unit over a period of 12 months (January 2016 to December 2016). There were 77 cases of electrical burns under the age of 16 years. High voltage burns predominated and older age groups were more frequently affected. Male:female ratio was 4.1:1. Amputations were required in 18 (23%), skin grafting in 52 (67%) and flap cover in 29 (37%) patients. There were unfavourable outcomes in 32% patients with a mortality rate of 7.8%. Significant association was found between unfavourable outcomes and high voltage burn injuries and length of hospital stay. The impact of electrical burn injuries is substantial and can be reduced by simple preventive measures such as educating parents, improving health infrastructure and adherence to safety regulations.

77 FR 13582 - Disability and Rehabilitation Research Project; Burn Model Systems Centers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

.... (2008). A clarion to recommit and reaffirm burn rehabilitation. Journal of Burn Care & Research, 29(3... injury. Journal of Burn Care & Research, 30(2), 294-300. Schneider, J.C., Holavanahalli, R., Helm, P... for the year of 2009. Journal of Burn Care & Research, 31(6), 836-848. Ullrich, P.M., Askay, SW...

Quantifying Risk Factors for Long-Term Sleep Problems After Burn Injury in Young Adults.

PubMed

Lee, Austin F; Ryan, Colleen M; Schneider, Jeffrey C; Kazis, Lewis E; Li, Nien Chen; Rose, Mary; Liang, Matthew H; Wang, Chao; Palmieri, Tina; Meyer, Walter J; Pidcock, Frank S; Reilly, Debra; Sheridan, Robert L; Tompkins, Ronald G

Restorative sleep is an important component of quality of life. Disturbances in sleep after burn injury were reported but all based on uncontrolled or nonstandardized data. The occurrence and the effect of long-term sleep problems in young adult burn survivors have not been well defined. This 5-year (2003-2008) prospective multicenter longitudinal study included adults with burn injuries ages 19 to 30 years who completed the Young Adult Burn Outcome Questionnaire (YABOQ) up to 36 months after injury. The items measured 15 patient-reported outcomes including physical, psychological, and social statuses and symptoms such as itch and pain. Scores of these 15 YABOQ outcome domains were standardized to a mean of 50 and a SD of 10 based on an age-matched nonburned reference group of young adults. Sleep quality was assessed using the item 'How satisfied are you now with your sleep,' rated by a 5-point Likert scale. Patients responding with very and somewhat dissatisfied were classified as having sleep dissatisfaction and the remaining as less or not dissatisfied. The associations between sleep dissatisfaction (yes/no) and YABOQ outcome domains were analyzed longitudinally using mixed-effect generalized linear models, adjusted for %TBSA burned, age, gender, and race. Generalized estimating equations were used to take into account correlated error resulting from repeated surveys on each patient over time. One hundred and fifty-two burn survivors participated in the YABOQ survey at baseline and during the follow-up who had at least one survey with a response to the sleep item. Among them, sleep dissatisfaction was twice as prevalent (76/152, 50%) when compared with the nonburned reference group (29/112, 26%). The likelihood of a burn survivor being dissatisfied with sleep was reduced over time after the burn injury. Sleep dissatisfaction following burns was significantly associated, in a dose-dependent manner, with increasing burn size (P = .001). Better sleep was associated with better outcomes in all domains (P < .05) except Fine Motor Function, and this association was significantly more apparent in the longer term compared with the shorter term with the same domains (P < .05). Dissatisfaction with sleep is highly prevalent following burn injuries in young adults. Lower satisfaction with sleep is associated with poorer scores in nearly all quality of life measures. Satisfaction with sleep should be addressed during the long-term clinical follow-up of young adults with burn injuries. Further research should be undertaken to understand the components of sleep quality that are important to burn survivors and which ones might be modified and tested in future intervention studies.

"Fire Moss" Cover and Function in Severely Burned Forests of the Western United States

NASA Astrophysics Data System (ADS)

Grover, H.; Doherty, K.; Sieg, C.; Robichaud, P. R.; Fulé, P. Z.; Bowker, M.

2017-12-01

With wildfires increasing in severity and extent throughout the Western United States, land managers need new tools to stabilize recently burned ecosystems. "Fire moss" consists of three species, Ceratodon purpureus, Funaria hygrometrica, and Bryum argentum. These mosses colonize burned landscapes quickly, aggregate soils, have extremely high water holding capacity, and can be grown rapidly ex-situ. In this talk, I will focus on our efforts to understand how Fire Moss naturally interacts with severely burned landscapes. We examined 14 fires in Arizona, New Mexico, Washington, and Idaho selecting a range of times since fire, and stratified plots within each wildfire by winter insolation and elevation. At 75+ plots we measured understory plant cover, ground cover, Fire Moss cover, and Fire Moss reproductive effort. On plots in the Southwest, we measured a suite of soil characteristics on moss covered and adjacent bare soil including aggregate stability, shear strength, compressional strength, and infiltration rates. Moss cover ranged from 0-75% with a mean of 16% across all plots and was inversely related to insolation (R2 = .32, p = <.01), directly related to elevation (R2 = .13, p = .02), and not related to slope (R2 = .02, p =.41). Moss covered areas had twice as much shear strength and compressional strength, and three times higher aggregate stability and infiltration rates as adjacent bare ground. These results will allow us to model locations where Fire Moss will naturally increase postfire hillslope soil stability, locations for targeting moss restoration efforts, and suggest that Fire Moss could be a valuable tool to mitigate post wildfire erosion.

An experimental study of high-pressure droplet combustion

NASA Technical Reports Server (NTRS)

Norton, Chris M.; Litchford, Ron J.; Jeng, San-Mou

1990-01-01

The results are presented of an experimental study on suspended n-heptane droplet combustion in air for reduced pressures up to P(r) = 2.305. Transition to fully transient heat-up through the critical state is demonstrated above a threshold pressure corresponding to P(r) of roughly 1.4. A silhouette imaging technique resolves the droplet surface for reduced pressures up to about P(r) roughly 0.63, but soot formation conceals the surface at higher pressures. Images of the soot plumes do not show any sudden change in behavior indicative of critical transition. Mean burning rate constants are computed from the d-squared variation law using measured effective droplet diameters at ignition and measured burn times, and corrected burning times are computed for an effective initial droplet diameter. The results show that the burning rates increase as the fuel critical pressure is approached and decrease as the pressure exceeds the fuel critical pressure. Corrected burning times show inverse behavior.

[Burn injuries to military personnel during the Six Day War].

PubMed

Dreyfuss, U Y

2000-05-01

About 2500 soldiers were injured during the Six Day War (June 1967) of whom 115 suffered from burns. In 34 of them 15% or more of their body surface was involved and 11 died. Typical features of these burn cases were supplementary injuries, a high rate of infection, and long periods of hospitalization. Prophylactic antibiotics were not useful. The general condition of many deteriorated during the first week after injury, indicating the importance of treating severe burns in specialized facilities.

Credit PSR. This photograph looks south southwest (200°) into the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit PSR. This photograph looks south southwest (200°) into the burn pit. Scrap propellant was stored elsewhere until enough had accumulated to require a burn. The open burn unit is rated for 200 pounds (91 Kg) of class 1.1 propellants, or 1,000 pounds (454 Kg) of class 1.3 propellants. A maximum of 4 personnel were permitted on the grounds during a burn - Jet Propulsion Laboratory Edwards Facility, Incinerator, Edwards Air Force Base, Boron, Kern County, CA

High severity experimental burns in Siberian larch forests increase permafrost thaw and larch tree regeneration

NASA Astrophysics Data System (ADS)

Alexander, H. D.; Davydov, S.; Zimov, N.; Mack, M. C.

2013-12-01

Global change models predict increased fire activity in boreal forests as climate warms and dries. We hypothesized that fire-driven decreases in soil organic layer (SOL) depth will (1) increase permafrost thaw by reducing the insulating capacity of the SOL and (2) improve seedbed conditions for tree regeneration. Over time, these changes will lead to altered patterns of above- and belowground carbon (C) accumulation. To test these hypotheses, we conducted plot-level experimental burns in July 2012 in a low-density, mature larch stand near the Northeast Science Station in Cherskii, Siberia. Dried fuels of naturally occurring vegetation were added to plots to achieve four burn severity treatments based on residual SOL depths: control, low (> 8 cm), moderate (5-8 cm), and high severity (2-5 cm). Pre-fire and during two growing seasons post-fire, we measured thaw depth, soil moisture, and soil temperature to determine severity effects on permafrost thaw. We also sowed larch seeds in fall 2012 and quantified germination rates the following growing season. By 1 wk post-fire, thaw depth was 15-25 cm deeper in plots burned at high severity (55 cm) compared to other treatments (30-40 cm). These differences in thaw depth with burn severity were maintained during the subsequent growing season and were associated with increased soil temperature and moisture. Larch regeneration was 10x higher on severely burned plots than those unburned. Our findings highlight the potential for increased fire severity to degrade permafrost and alter successional dynamics and patterns of C accumulation.

Artemisinin protects mice against burn sepsis through inhibiting NLRP3 inflammasome activation.

PubMed

Long, Huibao; Xu, Bincan; Luo, Yanling; Luo, Keqin

2016-05-01

NLRP3 inflammasome activation is recently reported to be linked to the pathogenesis of sepsis. Artemisinin is shown to play beneficial effects in sepsis. However, the impacts of artemisinin on burn sepsis have not been investigated. This study is designed to investigate the role of artemisinin in burn sepsis and the involvement of NLRP3 inflammasome activation. Male BALB/c mice were randomly divided into sham burn, burn, burn sepsis, and artemisinin treated groups. Inflammatory cytokines were measured by enzyme-linked immunosorbent assay. Adhesion molecules and neutrophil infiltration in lung and heart were detected by real-time polymerase chain reaction. Mortality rates were monitored. Artemisinin was added to Raw 264.7 cells that were stimulated with burn sepsis serum in the presence/absence of an inhibitor of NLRP3 inflammasome, 3, 4-methylenedioxy-β-nitrostyrene. Interleukin (IL) 1β and IL-18 messenger RNA expression as well as NLRP3 and caspase 1 protein were measured. Production of inflammatory cytokines in serum, levels of adhesion molecules and neutrophil infiltration in lung and heart, and mortality rate of burn septic mice were significantly higher than those of control. These effects were attenuated by artemisinin. Artemisinin down-regulated protein levels of NLRP3 and caspase 1 and inhibited the increases of IL-1β and IL-18 messenger RNA expression from Raw 264.7 cells that were stimulated with burn sepsis serum. These effects of artemisinin were not further strengthened in the presence of 4-methylenedioxy-β-nitrostyrene. Artemisinin protects mice from burn sepsis by attenuating the inflammatory response and alleviating inflammatory infiltration in vital organs, likely through inhibiting the activation of NLRP3 inflammasome. Copyright © 2016 Elsevier Inc. All rights reserved.

Review of the use of povidone-iodine (PVP-I) in the treatment of burns.

PubMed

Steen, M

1993-01-01

Local infection and burn wound sepsis are one of the most severe problems in the treatment of thermally injured patients. Early surgical treatment and the use of topical antiseptics led to a decrease in the infection rate and significantly improved the survival rate of burns patients within the last twenty-five years. Many antiseptics are used in the treatment of burns. Silver nitrate, silver sulphadiazine, sulfamylon and povidone-iodine (PVP-I) are the most common substances used worldwide in burn care facilities. Clinical studies demonstrate that treatment with PVP-I is the most effective against bacterial and fungal infection. Several methodological problems however arise from direct comparison between these antiseptics, and local and systemic adverse effects can make the right choice difficult. Some case reports documented possible side effects in the treatment of patients with PVP-I, leading to general concerns about this treatment. Absorption of iodine and possible changes in thyroid hormones are well known, but evaluation of the clinical consequences is controversial. Reports of severe metabolic acidosis and renal insufficiency with lethal results have condemned the use of PVP-I in the treatment of extensive burns. The case reports, however, dealt with patients suffering from general morbidity and sepsis and therefore these single reports may not be generally valid. Local treatment of burns may cause further problems. The beneficial effect of a decrease of bacterial counts in deeper tissue may be confounded by other effects delaying wound healing, as shown in some experimental studies. Controlled clinical investigations on burn patients however are still missing. The paper will discuss these topics in detail referring to the treatment of burns with PVP-I. It is based on a critical review of the literature and the author's own experience in burns therapy.

Upon admission coagulation and platelet function in patients with thermal and electrical injuries.

PubMed

Wade, Charles E; Baer, Lisa A; Cardenas, Jessica C; Folkerson, Lindley E; Nutall-Aurora, Kisha; Cotton, Bryan A; Matijevic, Nena; Holcomb, John B; Cross, James M; Huzar, Todd

2016-12-01

There has been increased focus on hemostatic potential and function in the initial assessment of the patient with traumatic injuries, that not been extensively studied in patients with burns. We proposed to determine the hemostatic potential of patients with burns upon admission to the emergency department and contrasted their condition with that of healthy controls and patients with other traumatic injuries. In addition we assessed differences due to thermal versus electrical injury and evaluated the effect of burn size. This is a patient based prospective observational study conducted with delayed consented. Subjects at the highest level of trauma activation upon admission to the ED had a blood sample collected for research purposes and were subsequently consented. Hemostatic potential was measured by rapid thromelastography (r-TEG ® ), thrombin generation by calibrated automated thrombogram (CAT) and platelet function by Multiplate ® using five activators. Burn subjects were compared to subjects with other traumatic injuries and controls. Within the burn subjects additional analysis compared mechanism (thermal vs. electrical) and burn size. Values are medians (IQR). Two hundred and eighty two trauma patients (with burns n=40, 14%) and 27 controls were enrolled. Upon admission, compared to controls, subjects with burns or trauma were hyper-coagulable based on r-TEG and CAT, with increased rates of clot formation and thrombin generation. There were no differences in burns compared to other traumatic injuries. The presence of hyper-coagulation did not appear to be related to the type of burn or the percentage of total body surface area involved. Employing previous defined cut points for R-TEG driven therapeutic interventions burn patients had similar rates of hyper- and hypo-coagulation noted in patients with traumatic injuries. Upon admission patients with burns are in a hyper-coagulable state similar to that of other trauma patients. Employing demonstrated cut points of hemostatic potential in trauma patients associated with increased risk of poor outcomes demonstrated the incidence in burn patients to be similar, suggesting that these values could be used in the early assessment of the patient with burns to guide treatment interventions. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.