Development and Implementation of a Bus Driver Training Program.

ERIC Educational Resources Information Center

Buchovecky, John G.

A bus driver training program was developed and implemented in a rural school district in an effort to improve the driving skills of the bus drivers. The program was tailored to meet the needs of the bus drivers and utilized various community agencies for demonstration and teaching purposes. The subject areas included in the program were driver…

Methodology for measurement of diesel particle size distributions from a city bus working in real traffic conditions

NASA Astrophysics Data System (ADS)

Armas, O.; Gómez, A.; Mata, C.

2011-10-01

The study of particulate matter (PM) and nitrogen oxides emissions of diesel engines is nowadays a necessary step towards pollutant emission reduction. For a complete evaluation of PM emissions and its size characterization, one of the most challenging goals is to adapt the available techniques and the data acquisition procedures to the measurement and to propose a methodology for the interpretation of instantaneous particle size distributions (PSD) of combustion-derived particles produced by a vehicle during real driving conditions. In this work, PSD from the exhaust gas of a city bus operated in real driving conditions with passengers have been measured. For the study, the bus was equipped with a rotating disk diluter coupled to an air supply thermal conditioner (with an evaporating tube), the latter being connected to a TSI Engine Exhaust Particle Sizer spectrometer. The main objective of this work has been to propose an alternative procedure for evaluating the influence of several transient sequences on PSD emitted by a city bus used in real driving conditions with passengers. The transitions studied were those derived from the combination of four possible sequences or categories during real driving conditions: idle, acceleration, deceleration with fuel consumption and deceleration without fuel consumption. The analysis methodology used in this work proved to be a useful tool for a better understanding of the phenomena related to the determination of PSD emitted by a city bus during real driving conditions with passengers.

Analysis of a diesel-electric hybrid urban bus system

NASA Astrophysics Data System (ADS)

Marr, W. W.; Sekar, R. R.; Ahlheim, M. C.

A hybrid bus powered by a diesel engine and a battery pack was analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, were evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

Economical launching and accelerating control strategy for a single-shaft parallel hybrid electric bus

NASA Astrophysics Data System (ADS)

Yang, Chao; Song, Jian; Li, Liang; Li, Shengbo; Cao, Dongpu

2016-08-01

This paper presents an economical launching and accelerating mode, including four ordered phases: pure electrical driving, clutch engagement and engine start-up, engine active charging, and engine driving, which can be fit for the alternating conditions and improve the fuel economy of hybrid electric bus (HEB) during typical city-bus driving scenarios. By utilizing the fast response feature of electric motor (EM), an adaptive controller for EM is designed to realize the power demand during the pure electrical driving mode, the engine starting mode and the engine active charging mode. Concurrently, the smoothness issue induced by the sequential mode transitions is solved with a coordinated control logic for engine, EM and clutch. Simulation and experimental results show that the proposed launching and accelerating mode and its control methods are effective in improving the fuel economy and ensure the drivability during the fast transition between the operation modes of HEB.

An Inverter Packaging Scheme for an Integrated Segmented Traction Drive System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Gui-Jia; Tang, Lixin; Ayers, Curtis William

The standard voltage source inverter (VSI), widely used in electric vehicle/hybrid electric vehicle (EV/HEV) traction drives, requires a bulky dc bus capacitor to absorb the large switching ripple currents and prevent them from shortening the battery s life. The dc bus capacitor presents a significant barrier to meeting inverter cost, volume, and weight requirements for mass production of affordable EVs/HEVs. The large ripple currents become even more problematic for the film capacitors (the capacitor technology of choice for EVs/HEVs) in high temperature environments as their ripple current handling capability decreases rapidly with rising temperatures. It is shown in previous workmore » that segmenting the VSI based traction drive system can significantly decrease the ripple currents and thus the size of the dc bus capacitor. This paper presents an integrated packaging scheme to reduce the system cost of a segmented traction drive.« less

Who's Really Driving Student Outcomes?

ERIC Educational Resources Information Center

Meals, Anthony R.

2018-01-01

The author, a teacher and substitute bus driver, explains the pivotal role that bus drivers play in the education process by proving safe transport and getting students off to a good start each day. Reducing bus transportation budgets, or charging families for using it, reduces student access to education.

TMS communications software. Volume 1: Computer interfaces

NASA Technical Reports Server (NTRS)

Brown, J. S.; Lenker, M. D.

1979-01-01

A prototype bus communications system, which is being used to support the Trend Monitoring System (TMS) as well as for evaluation of the bus concept is considered. Hardware and software interfaces to the MODCOMP and NOVA minicomputers are included. The system software required to drive the interfaces in each TMS computer is described. Documentation of other software for bus statistics monitoring and for transferring files across the bus is also included.

FPGA for Power Control of MSL Avionics

NASA Technical Reports Server (NTRS)

Wang, Duo; Burke, Gary R.

2011-01-01

A PLGT FPGA (Field Programmable Gate Array) is included in the LCC (Load Control Card), GID (Guidance Interface & Drivers), TMC (Telemetry Multiplexer Card), and PFC (Pyro Firing Card) boards of the Mars Science Laboratory (MSL) spacecraft. (PLGT stands for PFC, LCC, GID, and TMC.) It provides the interface between the backside bus and the power drivers on these boards. The LCC drives power switches to switch power loads, and also relays. The GID drives the thrusters and latch valves, as well as having the star-tracker and Sun-sensor interface. The PFC drives pyros, and the TMC receives digital and analog telemetry. The FPGA is implemented both in Xilinx (Spartan 3- 400) and in Actel (RTSX72SU, ASX72S). The Xilinx Spartan 3 part is used for the breadboard, the Actel ASX part is used for the EM (Engineer Module), and the pin-compatible, radiation-hardened RTSX part is used for final EM and flight. The MSL spacecraft uses a FC (Flight Computer) to control power loads, relays, thrusters, latch valves, Sun-sensor, and star-tracker, and to read telemetry such as temperature. Commands are sent over a 1553 bus to the MREU (Multi-Mission System Architecture Platform Remote Engineering Unit). The MREU resends over a remote serial command bus c-bus to the LCC, GID TMC, and PFC. The MREU also sends out telemetry addresses via a remote serial telemetry address bus to the LCC, GID, TMC, and PFC, and the status is returned over the remote serial telemetry data bus.

Drive Control System for Pipeline Crawl Robot Based on CAN Bus

NASA Astrophysics Data System (ADS)

Chen, H. J.; Gao, B. T.; Zhang, X. H.; Deng2, Z. Q.

2006-10-01

Drive control system plays important roles in pipeline robot. In order to inspect the flaw and corrosion of seabed crude oil pipeline, an original mobile pipeline robot with crawler drive unit, power and monitor unit, central control unit, and ultrasonic wave inspection device is developed. The CAN bus connects these different function units and presents a reliable information channel. Considering the limited space, a compact hardware system is designed based on an ARM processor with two CAN controllers. With made-to-order CAN protocol for the crawl robot, an intelligent drive control system is developed. The implementation of the crawl robot demonstrates that the presented drive control scheme can meet the motion control requirements of the underwater pipeline crawl robot.

Integrated Inverter For Driving Multiple Electric Machines

DOEpatents

Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

2006-04-04

An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction. To date, however, their application to variable speed or servo drives was hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation of frequency and voltage allows independent control of rotor and stator flux, full four quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Variable speed induction motor operation from a 20-kHz power bus

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1989-01-01

Induction motors are recognized for their simple rugged construction to date, however, their application to variable speed or servo drives has been hampered by limitations on their control. Induction motor drives tend to be complex and to display troublesome low speed characteristics due in part to nonsinusoidal driving voltages. A technique was developed which involves direct synthesis of sinusoidal driving voltages from a high frequency power bus and independent control of frequency and voltages. Separation offrequency and voltage allows independent control of rotor and stator flux, full four-quadrant operation, and instantaneous torque control. Recent test results, current status of the technology, and proposed aerospace applications will be discussed.

Characterisation of an urban bus network for environmental purposes.

PubMed

André, Michel; Villanova, André

2004-12-01

Since pollutant emissions are closely related to the operating conditions of vehicles, their evaluation usually involves studying these operating conditions (through bus instrumentation and monitoring under actual operation), the design of representative driving or engine test cycles and the measurement of pollutant emissions. A preliminary characterisation of the routes on a bus network should make it possible to identify typical routes, the driving conditions and pollutant emissions of which are then studied. Two approaches are envisaged and applied to the Paris area, for which a wealth of information is available, which should be transferable to other bus networks. Both approaches are based on factorial analysis and automatic clustering, to allow optimum description and the identification of a pertinent typology of the bus routes in several classes. The first attempt at characterisation is based on statistics relating to bus operations: route characteristics (length, dedicated bus lanes, number of stops, location of stops: schools, tourist sites, hospitals, railways or underground stations), travel time, commercial speed, annual statistics (number of passengers, number of vehicles per hour, total kilometres), the irregularity of travel (variation of travel times, injuries, congestion.), as well as information on the problems encountered (congestion, distribution of the passenger load, junctions, bends). A second approach is based on the analysis of the "urban context" in which buses are driven. Population, employment, housing, road network, traffic and places that generate or disturb traffic (schools, railway stations, shopping areas, etc.) are calculated for the Ile de France region, by cells of 100 x 100 m, and collected in a geographical information system (GIS). Statistical analyses enable a typology of these urban cells to be established, the main parameters being density, type of housing, road types and traffic levels. The bus routes are then analysed according to their itineraries across these typical areas (distances travelled in each type of area) using a similar approach. A comparison of the typologies obtained from operational data and from urban data highlights the advantages and disadvantages of the two approaches. The first result from these typologies is the selection of routes which are representative of the different classes, in order to instrument buses and record driving patterns. This method should also make it possible to link driving conditions and urban characteristics, and then to allocate pollutant emission factors to given geographical situations, in particular, in the context of emission inventories or impact studies.

Variability of particle number emissions from diesel and hybrid diesel-electric buses in real driving conditions.

PubMed

Sonntag, Darrell B; Gao, H Oliver; Holmén, Britt A

2008-08-01

A linear mixed model was developed to quantify the variability of particle number emissions from transit buses tested in real-world driving conditions. Two conventional diesel buses and two hybrid diesel-electric buses were tested throughout 2004 under different aftertreatments, fuels, drivers, and bus routes. The mixed model controlled the confounding influence of factors inherent to on-board testing. Statistical tests showed that particle number emissions varied significantly according to the after treatment, bus route, driver, bus type, and daily temperature, with only minor variability attributable to differences between fuel types. The daily setup and operation of the sampling equipment (electrical low pressure impactor) and mini-dilution system contributed to 30-84% of the total random variability of particle measurements among tests with diesel oxidation catalysts. By controlling for the sampling day variability, the model better defined the differences in particle emissions among bus routes. In contrast, the low particle number emissions measured with diesel particle filters (decreased by over 99%) did not vary according to operating conditions or bus type but did vary substantially with ambient temperature.

Systems evaluation of thermal bus concepts

NASA Technical Reports Server (NTRS)

Stalmach, D. D.

1982-01-01

Thermal bus concepts, to provide a centralized thermal utility for large, multihundred kilowatt space platforms, were studied and the results are summarized. Concepts were generated, defined, and screened for inclusion in system level thermal bus trades. Parametric trade studies were conducted in order to define the operational envelope, performance, and physical characteristics of each. Two concepts were selected as offering the most promise for thermal bus development. All of four concepts involved two phase flow in order to meet the required isothermal nature of the thermal bus. Two of the concepts employ a mechanical means to circulate the working fluid, a liquid pump in one case and a vapor compressor in another. Another concept utilizes direct osmosis as the driving force of the thermal bus. The fourth concept was a high capacity monogroove heat pipe. After preliminary sizing and screening, three of these concepts were selected to carry into the trade studies. The monogroove heat pipe concept was deemed unsuitable for further consideration because of its heat transport limitations. One additional concept utilizing capillary forces to drive the working fluid was added. Parametric system level trade studies were performed. Sizing and weight calculations were performed for thermal bus sizes ranging from 5 to 350 kW and operating temperatures in the range of 4 to 120 C. System level considerations such as heat rejection and electrical power penalties and interface temperature losses were included in the weight calculations.

SunLine Test Drives Hydrogen Bus

DOT National Transportation Integrated Search

2003-08-01

SunLine collaborated with the U.S. Department of Energys (DOE) Hydrogen, Fuel Cells & Infrastructure Technologies (HFC&IT) Program on the evaluation of the 30-foot hybrid fuel cell bus that was developed by ThunderPower LLC, a joint venture by Tho...

Sudden illness while driving a vehicle--a retrospective analysis of commercial drivers in Japan.

PubMed

Hitosugi, Masahito; Gomei, Sayaka; Okubo, Takao; Tokudome, Shogo

2012-01-01

We performed a retrospective analysis of commercial drivers to clarify the background of incidents of sudden illness while driving. The analysis used reports submitted by employers to the Japan Ministry of Land, Infrastructure, Transport, and Tourism regarding commercial drivers who had been ordered to stop driving owing to health problems. Of 211 cases with an average work history of 15.2 years, there were 88 bus drivers, 70 taxi drivers, and 53 truck drivers, 36.0% of who had died as a result of their disease. Among taxi and truck drivers, more than 70% of incidents were due to cardiac, aortic, and cerebrovascular disease. More than 80% of these were unable to avoid traffic accidents caused by sudden illness. However, among bus drivers, cardiac, aortic, and cerebrovascular disease accounted for only 23.5% of incidents, and accidents were avoided in more than half of the cases. The duration between starting work and the incident time was significantly shorter among bus drivers [mean 3.3 hours, standard deviation (SD) 3.1] than taxi (7.7 hours, SD 5.8) and truck (7.2 hours, SD 6.3) drivers (P<0.01). The difference between the sudden illness rates of taxi and truck drivers and those of bus drivers is due to both reporting bias and differences in the awareness needed to prevent disabling events while driving. As a precaution, physicians should advise commercial drivers to stop driving as soon as they detect slight discomfort. To prevent accidents, more assertive health promotion aimed at professional drivers is needed.

58. VIEW OF SIGNAL BUS SECTION NUMBER 2 LOCATED OVER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

58. VIEW OF SIGNAL BUS SECTION NUMBER 2 LOCATED OVER THE CONTROL ROOM MEZZANINE IN THE SIGNAL POWER CONDITIONING ROOM. BUS IS A HEAVY COPPER BAR APPROXIMATELY 1/2" BY 4" WHICH CONDUCTS POWER THROUGHOUT THE POWER PLANT. BUS ARE PROTECTED BY A BRICK AND SOAPSTONE HOUSING. OPENINGS FOR INSPECTION AND ACCESS WOULD NORMALLY BE PROTECTED BY GLASS DOORS. THE BUS WOULD BE SUPPORTED ON INSULATORS WITHIN THE BRICK CHAMBER. BUS WAS REMOVED AND SALVAGED WHEN THE STATION WAS ABANDONED. THE OBJECT IN THE TOP CENTER OF THE PHOTOGRAPH IS A POTENTIAL TRANSFORMER USED TO REDUCE BUS POTENTIAL OF 2200 VOLTS TO LOW VOLTAGES SAFE FOR USE IN CONTROL ROOM CIRCUITRY. POTENTIAL TRANSFORMERS ARE PRECISION DEVICES WHICH PRODUCE AN ACCURATE LOW VOLTAGE ANALOG OF THE HIGH VOLTAGE ON THE BUS. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Electric drive systems including smoothing capacitor cooling devices and systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dede, Ercan Mehmet; Zhou, Feng

An electric drive system includes a smoothing capacitor including at least one terminal, a bus bar electrically coupled to the at least one terminal, a thermoelectric device including a first side and a second side positioned opposite the first side, where the first side is thermally coupled to at least one of the at least one terminal and the bus bar, and a cooling element thermally coupled to the second side of the thermoelectric device, where the cooling element dissipates heat from the thermoelectric device.

Quantifying the importance of image and perception to bus rapid transit : March 2009.

DOT National Transportation Integrated Search

2009-03-01

This study was designed to quantify the importance of image and perception to Bus Rapid Transit, by identifying the different underlying : tangible and intangible factors that drive any perceived differences between BRT and other forms of rapid trans...

Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles.

PubMed

Kado, Norman Y; Okamoto, Robert A; Kuzmicky, Paul A; Kobayashi, Reiko; Ayala, Alberto; Gebel, Michael E; Rieger, Paul L; Maddox, Christine; Zafonte, Leo

2005-10-01

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation catalyst) and from a vehicle fueled with low-sulfur diesel fuel (equipped with DPF) were lower than from the low-sulfur diesel fueled vehicle equipped with OC. All vehicle configurations had generally lower emissions of toxics than an uncontrolled diesel engine. Tunnel backgrounds (measurements without the vehicle running) were measured throughout this study and were helpful in determining the incremental increase in pollutant emissions. Also, the on-site determination of VOCs, especially 1,3-butadiene, helped minimize measurement losses due to sample degradation after collection.

Testing the effects of safety climate and disruptive children behavior on school bus drivers performance: A multilevel model.

PubMed

Zohar, Dov; Lee, Jin

2016-10-01

The study was designed to test a multilevel path model whose variables exert opposing effects on school bus drivers' performance. Whereas departmental safety climate was expected to improve driving safety, the opposite was true for in-vehicle disruptive children behavior. The driving safety path in this model consists of increasing risk-taking practices starting with safety shortcuts leading to rule violations and to near-miss events. The study used a sample of 474 school bus drivers in rural areas, driving children to school and school-related activities. Newly developed scales for measuring predictor, mediator and outcome variables were validated with video data taken from inner and outer cameras, which were installed in 29 buses. Results partially supported the model by indicating that group-level safety climate and individual-level children distraction exerted opposite effects on the driving safety path. Furthermore, as hypothesized, children disruption moderated the strength of the safety rule violation-near miss relationship, resulting in greater strength under high disruptiveness. At the same time, the hypothesized interaction between the two predictor variables was not supported. Theoretical and practical implications for studying safety climate in general and distracted driving in particular for professional drivers are discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Eudy, L.

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

Method for in-use measurement and evaluation of the activity, fuel use, electricity use, and emissions of a plug-in hybrid diesel-electric school bus.

PubMed

Choi, Hyung-Wook; Frey, H Christopher

2010-05-01

The purpose of this study is to demonstrate a methodology for characterizing at high resolution the energy use and emissions of a plug-in parallel-hybrid diesel-electric school bus (PHSB) to support assessments of sensitivity to driving cycles and comparisons to a conventional diesel school bus (CDSB). Data were collected using onboard instruments for a first-of-a-kind prototype PHSB and a CDSB of the same chassis and engine, operated on actual school bus routes. The engine load was estimated on the basis of vehicle specific power (VSP) and an empirically derived relationship between VSP and engine manifold absolute pressure (MAP). VSP depends on speed, acceleration, and road grade. For the PHSB, the observed electrical discharge or recharge to the traction motor battery was characterized on the basis of VSP. The energy use and emission rates of the PHSB from tailpipe and electricity use were estimated for five real-world driving cycles and compared to the engine fuel use and emissions of the CDSB. The PHSB had the greatest advantage on arterial routes and less advantage on highway or local routes. The coupled VSP-MAP modeling approach enables assessment of a wide variety of driving conditions and comparisons of vehicles with different propulsion technologies.

Prevalence of and factors associated with distraction among public transit bus drivers

PubMed Central

Griffin, Russell; Huisingh, Carrie; McGwin, Gerald

2015-01-01

Objective Recent research has suggested that driver distraction is a major cause of driving performance impairment and motor vehicle collisions. Research on the topic has focused on passenger vehicles, with studies suggesting that drivers may be distracted nearly 33% of the time spent driving. To date, no study has examined the prevalence of distraction specifically among public transit bus drivers. Methods Over a three-month period, trained investigators observed and recorded distraction behaviors of bus drivers. Distraction prevalence was compared by route characteristics (e.g., geographic area, travel speed) using chi-square test. A general estimating equation logistic regression was used to estimate p-values for distraction prevalence by driver demographics. Results Overall, there was a 39% prevalence of distraction. The most prevalent distractions were due to interactions with another passenger. Distractions were more prevalent among drivers <30 years of age or ≥50 years of age, on city streets or highways (relative to residential streets), and when there were more than 20 passengers. Distractions were the least prevalent in suburban areas, with the highest prevalence observed in city centers and rural areas. Conclusions Driver distraction is a common problem for public transit bus drivers, mainly due to other passengers. Drivers should be educated on the hazards of distracted driving and on ways to avoid distraction. PMID:24433192

Bus use and older people: a literature review applying the Person-Environment-Occupation model in macro practice.

PubMed

Broome, Kieran; McKenna, Kryss; Fleming, Jennifer; Worrall, Linda

2009-03-01

The same reasons that prompt older people to give up driving can also result in difficulties with accessing public transport. Difficulties using public transport can limit older people's participation in society, thereby impacting negatively on their health. Focusing on public buses, this review explicates the link between bus usability and the health of older people and frames existing evidence on bus usability issues. The Person-Environment-Occupation (PEO) model offers a framework by which bus usability can be assessed. A combination of person-centred, environmental, and occupation-related factors, including bus design, service provision and performance, information, and the attitudes of staff and the community, impact on older people's ability to catch buses. More systematic research needs to take place in order to develop a comprehensive understanding of bus usability. Occupational therapy has a key role to play in conceptualizing, implementing, and evaluating improvements in bus usability for older people.

Hydrogen-oxygen driven Zero Emissions bus draws attention at KSC

NASA Technical Reports Server (NTRS)

1999-01-01

KSC workers, with Center Director Roy Bridges (at right next to bus), head for the open door of the Zero Emissions (ZE) transit bus and a ride around the center. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product 'exhaust' from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available to employees for viewing and a ride, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27.

KSC-99pp1251

NASA Image and Video Library

1999-10-25

KSC workers, with Center Director Roy Bridges (at right next to bus), head for the open door of the Zero Emissions (ZE) transit bus and a ride around the center. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available to employees for viewing and a ride, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27

Hydrogen-oxygen driven Zero Emissions bus draws attention at KSC

NASA Technical Reports Server (NTRS)

1999-01-01

KSC employees, along with Center Director Roy Bridges (second from left), view the hydrogen-oxygen driven engine powering a Zero Emissions (ZE) transit bus. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product 'exhaust' from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27.

Hydrogen-oxygen driven Zero Emissions bus draws attention at KSC

NASA Technical Reports Server (NTRS)

1999-01-01

On view in front of the Headquarters Building, the Zero Emissions (ZE) transit bus attracts an interested group of employees, including Center Director Roy Bridges (second from left in foreground). Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product 'exhaust' from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27.

Hydrogen-oxygen driven Zero Emissions bus draws attention at KSC

NASA Technical Reports Server (NTRS)

1999-01-01

In front of the Headquarters Building at KSC, Center Director Roy Bridges (left) looks at the hydrogen-oxygen driven engine powering a Zero Emissions (ZE) transit bus. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by- product 'exhaust' from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27.

Mass Transportation for NPS: A Financial Feasibility Study

DTIC Science & Technology

1992-06-01

working hours ? 4. Should the bus driver drive the bus the entire day or a portion of the day, with the rest of the day dedicated to normal duties? One...appropriate? 84 3. How should they be compensated for their extra working hours? Should they be taken off the watchbill? Should they be allowed flexible

Battery capacity and recharging needs for electric buses in city transit service

DOE PAGES

Gao, Zhiming; Lin, Zhenhong; LaClair, Tim J.; ...

2017-01-27

Our paper evaluates the energy consumption and battery performance of city transit electric buses operating on real day-to-day routes and standardized bus drive cycles, based on a developed framework tool that links bus electrification feasibility with real-world vehicle performance, city transit bus service reliability, battery sizing and charging infrastructure. The impacts of battery capacity combined with regular and ultrafast charging over different routes have been analyzed in terms of the ability to maintain city transit bus service reliability like conventional buses. These results show that ultrafast charging via frequent short-time boost charging events, for example at a designated bus stopmore » after completing each circuit of an assigned route, can play a significant role in reducing the battery size and can eliminate the need for longer duration charging events that would cause schedule delays. Furthermore, the analysis presented shows that significant benefits can be realized by employing multiple battery configurations and flexible battery swapping practices in electric buses. These flexible design and use options will allow electric buses to service routes of varying city driving patterns and can therefore enable meaningful reductions to the cost of the vehicle and battery while ensuring service that is as reliable as conventional buses.« less

Battery capacity and recharging needs for electric buses in city transit service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Lin, Zhenhong; LaClair, Tim J.

Our paper evaluates the energy consumption and battery performance of city transit electric buses operating on real day-to-day routes and standardized bus drive cycles, based on a developed framework tool that links bus electrification feasibility with real-world vehicle performance, city transit bus service reliability, battery sizing and charging infrastructure. The impacts of battery capacity combined with regular and ultrafast charging over different routes have been analyzed in terms of the ability to maintain city transit bus service reliability like conventional buses. These results show that ultrafast charging via frequent short-time boost charging events, for example at a designated bus stopmore » after completing each circuit of an assigned route, can play a significant role in reducing the battery size and can eliminate the need for longer duration charging events that would cause schedule delays. Furthermore, the analysis presented shows that significant benefits can be realized by employing multiple battery configurations and flexible battery swapping practices in electric buses. These flexible design and use options will allow electric buses to service routes of varying city driving patterns and can therefore enable meaningful reductions to the cost of the vehicle and battery while ensuring service that is as reliable as conventional buses.« less

Bus Driver Training Simulator Assessment

DOT National Transportation Integrated Search

1980-01-01

Simulation has become an increasingly important tool in driving research, highway research, and vehicle design. This report documents the results of an investigation into the feasibility of developing a driving simulator as a means of teaching safe d...

77 FR 12360 - Qualification of Drivers; Exemption Applications; Epilepsy and Seizure Disorders

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

... known medical condition (e.g., drug reaction, high temperature, acute infectious disease, dehydration... exemption, he would return to driving a school bus. His physician has released him to return to driving...

Zion National Park Propane-to-Electric Shuttle Bus Testing | Transportation

Science.gov Websites

storage requirements based on the fleet's unique operation. NREL will process and analyze the data using specialized tools-including the Drive-Cycle Rapid Investigation, Visualization, and Evaluation (DRIVE) tool

KSC-99pp1248

NASA Image and Video Library

1999-10-25

In front of the Headquarters Building at KSC, Center Director Roy Bridges (left) looks at the hydrogen-oxygen driven engine powering a Zero Emissions (ZE) transit bus. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27

KSC-99pp1249

NASA Image and Video Library

1999-10-25

KSC employees, along with Center Director Roy Bridges (second from left), view the hydrogen-oxygen driven engine powering a Zero Emissions (ZE) transit bus. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27

KSC-99pp1253

NASA Image and Video Library

1999-10-25

The Zero Emissions (ZE) transit bus passes a mock-up orbiter named Explorer on a trek through the KSC Visitor Complex. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. The ZE bus is being used on tour routes at the KSC Visitor Complex for two days to introduce the public to the concept

COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Daw, C Stuart; Smith, David E

2016-01-01

The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowestmore » average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.« less

Stress-related psychosocial factors at work, fatigue, and risky driving behavior in bus rapid transport (BRT) drivers.

PubMed

Useche, Sergio A; Ortiz, Viviola Gómez; Cendales, Boris E

2017-07-01

There is consistent scientific evidence that professional drivers constitute an occupational group that is highly exposed to work related stressors. Furthermore, several recent studies associate work stress and fatigue with unsafe and counterproductive work behaviors. This study examines the association between stress-related work conditions of Bus Rapid Transport (BRT) drivers and risky driving behaviors; and examines whether fatigue is a mechanism that mediates the association between the two. A sample of 524 male Bus Rapid Transit (BRT) operators were drawn from four transport companies in Bogotá, Colombia. The participants answered a survey which included an adapted version of the Driver Behavior Questionnaire (DBQ) for BRT operators, as well as the Effort-Reward Imbalance and Job Content Questionnaires, the Subjective Fatigue subscale of the Checklist Individual Strength (CIS) and the Need for Recovery after Work Scale (NFR). Utilizing Structural Equation Models (SEM) it was found that risky driving behaviors in BRT operators could be predicted through job strain, effort-reward imbalance and social support at work. It was also found that fatigue and need for recovery fully mediate the associations between job strain and risky driving, and between social support and risky driving, but not the association between effort/reward imbalance (ERI) and risky driving. The results of this study suggest that a) stress related working conditions (Job Strain, Social Support and ERI) are relevant predictors of risky driving in BRT operators, and b) that fatigue is the mechanism which links another kind of stress related to working conditions (job strain and low social support) with risky driving. The mechanism by which ERI increases risky driving in BRT operators remains unexplained. This research suggests that in addition to the individual centered stress-reduction occupational programs, fatigue management interventions aimed to changing some working conditions may reduce risky driving behaviors and promote safety in the professional drivers' jobs and on the road. Copyright © 2017 Elsevier Ltd. All rights reserved.

Static power reduction for midpoint-terminated busses

DOEpatents

Coteus, Paul W [Yorktown Heights, NY; Takken, Todd [Brewster, NY

2011-01-18

A memory system is disclosed which is comprised of a memory controller and addressable memory devices such as DRAMs. The invention provides a programmable register to control the high vs. low drive state of each bit of a memory system address and control bus during periods of bus inactivity. In this way, termination voltage supply current can be minimized, while permitting selected bus bits to be driven to a required state. This minimizes termination power dissipation while not affecting memory system performance. The technique can be extended to work for other high-speed busses as well.

Research on fuel cell and battery hybrid bus system parameters based on ADVISOR

NASA Astrophysics Data System (ADS)

Lai, Lianfeng; Lu, Youwen; Guo, Weiwei; Lin, Yuxiang; Xie, Yichun; Zheng, Liping; Chen, Wei; Liang, Boshan

2018-06-01

This paper aims at the fuel cell and battery hybrid automobile, based on one bus parameters, considers their own characteristics of fuel cell and battery and power demand when automobiles start, accelerate, climb, brake and other different working conditions, calculate the hybrid bus system parameters that match the fuel cell/battery., and ADVISOR is used is to verify simulation. The results show that the parameters of power drive system of this electric automobile are reasonable, and can meet the requirements of dynamic design indexes.

KSC-99pp1250

NASA Image and Video Library

1999-10-25

On view in front of the Headquarters Building, the Zero Emissions (ZE) transit bus attracts an interested group of employees, including Center Director Roy Bridges (second from left in foreground). Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. Available for viewing by employees, the ZE bus is also being used on tour routes at the KSC Visitor Complex Oct. 26-27

49 CFR 392.62 - Safe operation, buses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Prohibited Practices § 392.62 Safe operation, buses. No person shall drive a bus and a motor...

Evaluation of the Greenwood Drive fringe parking facility.

DOT National Transportation Integrated Search

1978-01-01

The application of a procedural method for planning express bus-fringe parking transit to determine why the Greenwood Drive service in Portsmouth, Virginia, failed to attract more riders than it did is described. The analysis of the study area reveal...

Teaching Kids with Learning Disabilities to Take Public Transit

ERIC Educational Resources Information Center

Schoenfeld, Jane

2009-01-01

Taking public transit can make anyone nervous, especially in a large or medium-sized city where there are many different bus lines going many different places. The author's daughter, Anna, has multiple learning disabilities and may never learn to drive, but she wants to be as independent as possible so the author taught her to ride the bus. This…

Beyond a man's world: contributions from considering gender in the study of bus drivers' work activity.

PubMed

Cunha, Liliana; Nogueira, Sónia; Lacomblez, Marianne

2014-01-01

Bus driving is a typically male occupation undergoing a process of feminization. Although men remain a majority, women's integration has raised some questions, namely, related to work organization or its impact on health. This paper focuses on the contributions of assuming a gender perspective in the analysis of the bus driving occupation and the conditions under which it is performed. Twenty female and 158 male bus drivers. Qualitative and quantitative approaches were combined. Ergonomic work analysis and individual interviews were used, as well as INSAT (Work and Health Questionnaire). Difficulties inherent to the work activity were highlighted, in terms of working hours and management of "peripheral tasks", with implications for the balance between professional and personal life. These difficulties were reported differently by men and women, although both made themselves clear about the impact on their career and health. Taking gender into consideration has enabled an enrichment of the questions that guide the analysis of this work activity, and contributed to a new perspective on the work performed by this occupational group as well as a new approach to study the history of the transport industry by proposing as focus of analysis issues related to "gender mobility".

Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

DOE PAGES

Gao, Zhiming; Daw, C. Stuart; Smith, David E.; ...

2016-08-01

The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which hasmore » the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.« less

Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; Daw, C. Stuart; Smith, David E.

The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which hasmore » the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.« less

Power inverter with optical isolation

DOEpatents

Duncan, Paul G.; Schroeder, John Alan

2005-12-06

An optically isolated power electronic power conversion circuit that includes an input electrical power source, a heat pipe, a power electronic switch or plurality of interconnected power electronic switches, a mechanism for connecting the switch to the input power source, a mechanism for connecting comprising an interconnecting cable and/or bus bar or plurality of interconnecting cables and/or input bus bars, an optically isolated drive circuit connected to the switch, a heat sink assembly upon which the power electronic switch or switches is mounted, an output load, a mechanism for connecting the switch to the output load, the mechanism for connecting including an interconnecting cable and/or bus bar or plurality of interconnecting cables and/or output bus bars, at least one a fiber optic temperature sensor mounted on the heat sink assembly, at least one fiber optic current sensor mounted on the load interconnection cable and/or output bus bar, at least one fiber optic voltage sensor mounted on the load interconnection cable and/or output bus bar, at least one fiber optic current sensor mounted on the input power interconnection cable and/or input bus bar, and at least one fiber optic voltage sensor mounted on the input power interconnection cable and/or input bus bar.

KSC-99pp1252

NASA Image and Video Library

1999-10-25

The Zero Emissions (ZE) transit bus tours the KSC Visitor Complex for a test ride. In the background are a mock-up orbiter named Explorer (left) and a stack of solid rocket boosters and external tank (right), typically used on Shuttle launches. Provided by dbb fuel cell engines inc. of Vancouver, Canada, the ZE bus was brought to KSC as part of the Center's Alternative Fuel Initiatives Program. The bus uses a Proton Exchange Membrane fuel cell in which hydrogen and oxygen, from atmospheric air, react to produce electricity that powers an electric motor drive system. The by-product "exhaust" from the fuel cell is water vapor, thus zero harmful emissions. A typical diesel-powered bus emits more than a ton of harmful pollutants from its exhaust every year. The ZE bus is being used on tour routes at the KSC Visitor Complex for two days to introduce the public to the concept

Evolutionary algorithm for vehicle driving cycle generation.

PubMed

Perhinschi, Mario G; Marlowe, Christopher; Tamayo, Sergio; Tu, Jun; Wayne, W Scott

2011-09-01

Modeling transit bus emissions and fuel economy requires a large amount of experimental data over wide ranges of operational conditions. Chassis dynamometer tests are typically performed using representative driving cycles defined based on vehicle instantaneous speed as sequences of "microtrips", which are intervals between consecutive vehicle stops. Overall significant parameters of the driving cycle, such as average speed, stops per mile, kinetic intensity, and others, are used as independent variables in the modeling process. Performing tests at all the necessary combinations of parameters is expensive and time consuming. In this paper, a methodology is proposed for building driving cycles at prescribed independent variable values using experimental data through the concatenation of "microtrips" isolated from a limited number of standard chassis dynamometer test cycles. The selection of the adequate "microtrips" is achieved through a customized evolutionary algorithm. The genetic representation uses microtrip definitions as genes. Specific mutation, crossover, and karyotype alteration operators have been defined. The Roulette-Wheel selection technique with elitist strategy drives the optimization process, which consists of minimizing the errors to desired overall cycle parameters. This utility is part of the Integrated Bus Information System developed at West Virginia University.

Traffic rule violations of private bus drivers and bus crashes in Sri Lanka: a case-control study.

PubMed

Jayatilleke, Achala Upendra; Poudel, Krishna C; Nakahara, Shinji; Dharmaratne, Samath D; Jayatilleke, Achini Chinthika; Jimba, Masamine

2010-06-01

To explore the association between self-reported traffic rule violations of private sector bus drivers and bus crashes in the Kandy district, Sri Lanka. We carried out a case-control study from August to September 2006. Cases were all the private bus drivers registered in the Kandy district and involved in crashes reported to the police between November 2005 and April 2006 (n = 63). We included two control groups: the private bus drivers working on the same routes of the cases (n = 90; matched controls) and the drivers selected randomly from the other routes of the district (n = 111; unmatched controls). We used a self-administered questionnaire to collect data on the self-reported traffic rule violations and analyzed the association between the self-reported traffic rule violations and crashes using logistic regression. The following variables showed significant associations with private bus crashes: illegal overtaking (matched controls, adjusted odds ratio [AOR] = 14.78, unmatched controls, AOR = 1.04), taking passengers outside the bus bays (matched controls, AOR = 3.96, unmatched controls, AOR = 2.29), and overloading (matched controls, AOR = 10.26, unmatched controls, AOR = 1.93). However, we did not observe an association between high-speed driving and bus crashes matched controls, AOR = 1.22, unmatched controls, AOR = 0.81. Traffic rule violations, such as illegal overtaking, overloading, and taking passengers outside the bus bays, are significant risk factors for private bus crashes in Sri Lanka.

Bus transit operational efficiency resulting from passenger boardings at park-and-ride facilities.

DOT National Transportation Integrated Search

2016-08-01

In order to save time and money by not driving to an ultimate destination, some urban commuters drive themselves a few miles to specially designated parking lots built for transit customers and located where trains or buses stop. The focus of this pa...

Kennesaw Mountain National Battlefield Park : Assessment of Management of Kennesaw Mountain Drive and Bus Shuttle Service.

DOT National Transportation Integrated Search

2010-07-06

The purpose of this study is to assess the management of the Kennesaw Mountain Drive, which runs from the Visitor Center to the : summit of Kennesaw Mountain, and assess the future of the shuttle service that operates on the road during weekends, inc...

CHARACTERIZATION OF HEAVY-DUTY MOTOR VEHICLE EMISSIONS UNDER TRANSIENT DRIVING CONDITIONS

EPA Science Inventory

The objective of this program was to characterize heavy-duty diesel truck and bus emissions produced during transient driving cycles. In the initial phase of the program an improved road-load simulation method was developed for use in operating large trucks on a chassis dynamomet...

Individual and population intake fractions of diesel particulate matter (DPM) in bus stop microenvironments.

PubMed

Xu, Jia; Jin, Taosheng; Miao, Yaning; Han, Bin; Gao, Jiajia; Bai, Zhipeng; Xu, Xiaohong

2015-12-01

Diesel particulate matter (DPM) is associated with adverse human health effects. This study aims to investigate the relationship between DPM exposure and emissions by estimating the individual intake fraction (iFi) and population intake fraction (iFp) of DPM. Daily average concentrations of particulate matter at two bus stops during rush hours were measured, and then they were apportioned to DPM due to heavy-duty diesel bus emissions using Chemical Mass Balance Model. The DPM emissions of diesel buses for different driving conditions (idling, creeping and traveling) were estimated on the basis of field observations and published emission factors. The median iFi of DPM was 0.67 and 1.39 per million for commuters standing at the bus stop and pedestrians/cyclists passing through the bus stop during rush hours, respectively. The median iFp of DPM was 94 per million. Estimations of iFi and iFp of DPM are potentially significant for exposure assessment and risk management. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Fuel Efficient Missile Combat Crew Routing Network.

DTIC Science & Technology

1980-06-01

after a 24 -hour alert tour, driving safety might be impacted. Al- though the 1.98 gallons per passenger is a 43% improvement over the present MCC...Van/DS II, Van/DS I, and 29 Pax Bus/ DS I combinations, the authors believe that the potential lengthy travel times, driving safety factor, vehicle

Electrical motor/generator drive apparatus and method

DOEpatents

Su, Gui Jia

2013-02-12

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

Savannah River bus project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Summers, W.A.

1998-08-01

The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogenmore » fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.« less

Effect of B20 and Low Aromatic Diesel on Transit Bus NOx Emissions Over Driving Cycles with a Range of Kinetic Intensity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lammert, M. P.; McCormick, R. L.; Sindler, P.

2012-10-01

Oxides of nitrogen (NOx) emissions for transit buses for up to five different fuels and three standard transit duty cycles were compared to establish whether there is a real-world biodiesel NOx increase for transit bus duty cycles and engine calibrations. Six buses representing the majority of the current national transit fleet and including hybrid and selective catalyst reduction systems were tested on a heavy-duty chassis dynamometer with certification diesel, certification B20 blend, low aromatic (California Air Resources Board) diesel, low aromatic B20 blend, and B100 fuels over the Manhattan, Orange County and UDDS test cycles. Engine emissions certification level hadmore » the dominant effect on NOx; kinetic intensity was the secondary driving factor. The biodiesel effect on NOx emissions was not statistically significant for most buses and duty cycles for blends with certification diesel, except for a 2008 model year bus. CARB fuel had many more instances of a statistically significant effect of reducing NOx. SCR systems proved effective at reducing NOx to near the detection limit on all duty cycles and fuels, including B100. While offering a fuel economy benefit, a hybrid system significantly increased NOx emissions over a same year bus with a conventional drivetrain and the same engine.« less

A design of high-precision BLDCM drive with bus voltage protection

NASA Astrophysics Data System (ADS)

Lian, Xuezheng; Wang, Haitao; Xie, Meilin; Huang, Wei; Li, Dawei; Jing, Feng

2017-11-01

In the application of space satellite turntable, the design of balance wheel is very necessary. To solve the acquisition precision of Brushless DC motor speed is low, and the encoder is also more complex, this paper improves the original hall signal measurement methods. Using the logic device to achieve the six frequency multiplication of hall signal, the signal is used as speed feedback to achieve speed closed-loop control and improve the speed stability. At the same time, in order to prevent the E.M.F of BLDC motor to raise the voltage of the bus bar when reversing or braking, and affect the normal operation of other circuit modules, the analog circuit is used to protect the bus bar voltage by the way of energy consumption braking. The experimental results are consistent with the theoretical design, and the rationality and feasibility of the frequency multiplication scheme and bus voltage protection scheme are verified.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

PubMed Central

2018-01-01

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety. PMID:29534530

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers.

PubMed

Montoro, Luis; Useche, Sergio; Alonso, Francisco; Cendales, Boris

2018-03-12

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

Defensive Driving.

ERIC Educational Resources Information Center

Sutton, Judy

1997-01-01

Discusses management issues surrounding school busing operations within the context of tightening budgets while simultaneously serving the growing number of students with special needs. The debate on bus use for advertising is highlighted. (GR)

Effects of the window openings on the micro-environmental condition in a school bus

NASA Astrophysics Data System (ADS)

Li, Fei; Lee, Eon S.; Zhou, Bin; Liu, Junjie; Zhu, Yifang

2017-10-01

School bus is an important micro-environment for children's health because the level of in-cabin air pollution can increase due to its own exhaust in addition to on-road traffic emissions. However, it has been challenging to understand the in-cabin air quality that is associated with complex airflow patterns inside and outside a school bus. This study conducted Computational Fluid Dynamics (CFD) modeling analyses to determine the effects of window openings on the self-pollution for a school bus. Infiltration through the window gaps is modeled by applying variable numbers of active computational cells as a function of the effective area ratio of the opening. The experimental data on ventilation rates from the literature was used to validate the model. Ultrafine particles (UFPs) and black carbon (BC) concentrations were monitored in ;real world; field campaigns using school buses. This modeling study examined the airflow pattern inside the school bus under four different types of side-window openings at 20, 40, and 60 mph (i.e., a total of 12 cases). We found that opening the driver's window could allow the infiltration of exhaust through window/door gaps in the back of school bus; whereas, opening windows in the middle of the school bus could mitigate this phenomenon. We also found that an increased driving speed (from 20 mph to 60 mph) could result in a higher ventilation rate (up to 3.4 times) and lower mean age of air (down to 0.29 time) inside the bus.

Study on emission characteristics of hybrid bus under driving cycles in typical Chinese city

NASA Astrophysics Data System (ADS)

Xie, Yongdong; Xu, Guangju

2017-09-01

In this study, hybrid city bus was taken as the research object, through the vehicle drum test, the vehicle emissions of hybrid bus, the transient emissions of gas pollutants, as well as the particle size and number distribution were surveyed. The results of the studies are listed as follows: First, compared to traditional fuel bus, hybrid bus could reduce about 44% of the NOx emissions, 33% of the total hydrocarbon emissions, and 51% of the particles emissions. Furthermore, the distribution of particles number concentration of test vehicle became high in middle and low in both sides. More specifically, the particle number concentration was mainly concentrated in the range from 0.021 to 0.755μm, the maximum was 0.2μm, and particle size of particulate matter (PM) less than 1.2μm accounted for 95% of the total number concentration. Particulate mass concentration was increased with increment of particle size, and the maximum of particulate mass (PM) concentration was 6.2μm. On average, whether traditional fuel bus or hybrid bus, the particle size of particulate matter(PM) less than 2.5μm accounted for more than 98% in the particles emission. It is found that the particles are more likely to deposit to the lung, respiratory bronchioles and alveoli, causing respiratory and lung diseases. Therefore, how to control the PM emissions of hybrid bus is the key factor of the study.

Bus Vent Design Evolution for the Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Woronowicz, Michael

2010-01-01

As a spacecraft undergoes ascent in a launch vehicle, its pressure environment transitions from one atmosphere to high vacuum in a matter of minutes. Venting of internal cavities is necessary to prevent the buildup of pressure differentials across cavity walls. Opposing the need to vent these volumes freely into space are thermal, optical, and electrostatic requirements for limiting or prohibiting the intrusion of unwanted energy into the same cavities. Bus vent design evolution is discussed for the Solar Dynamics Observatory. Design changes were influenced by a number of factors and concerns, such as contamination control, electrostatic discharge, changes in bus material, and driving fairing ascent pressure for a launch vehicle that was just entering service as this satellite project had gotten underway.

Measurement and comparison of Bangkok diesel bus emissions and performance using on-board equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnette, A.D.; Kishan, S.; Wangwongwatana, S.

1997-12-31

An on-board measurement system was assembled and used to compare the emissions and performance of buses in Bangkok, Thailand under actual driving conditions. Three similar buses were compared: one using an engine without special emissions control design, one with an engine meeting Euro 1 standards, and one with an engine meeting Euro 2 standards. As the buses drove their routes, second-by-second data were collected for engine rpm, throttle position, vehicle speed, exhaust concentrations of hydrocarbons, carbon monoxide, carbon dioxide, oxygen, nitric oxide, and exhaust opacity. Vehicle performance data were calculated using algorithms developed during previous driving studies in Bangkok. Grammore » per liter of fuel used emission factors were developed for gaseous pollutants using combustion calculations and these were translated into gram per kilometer traveled emission factors using the fuel efficiency data for the buses. Smoke data were left in terms of opacity. Test results are designed to be used to compare the cost benefit of upgrading buses with no emissions controls to Euro 1 or Euro 2 technologies. Ongoing tests will help bus companies determine the benefit of incremental improvements to bus engines and other emissions reduction strategies.« less

Lewis and Clark Park Shuttle: Lessons Learned.

DOT National Transportation Integrated Search

2006-08-01

In anticipation of increased visitation expected for the Lewis & Clark bicentennial, the park, Sunset Empire Transportation District, and other partners implemented a seasonal summer bus service that provided an alternative to driving to Fort Clatsop...

Predicting Airborne Particle Levels Aboard Washington State School Buses

PubMed Central

Adar, Sara D.; Davey, Mark; Sullivan, James R.; Compher, Michael; Szpiro, Adam; Liu, L.-J. Sally

2008-01-01

School buses contribute substantially to childhood air pollution exposures yet they are rarely quantified in epidemiology studies. This paper characterizes fine particulate matter (PM2.5) aboard school buses as part of a larger study examining the respiratory health impacts of emission-reducing retrofits. To assess onboard concentrations, continuous PM2.5 data were collected during 85 trips aboard 43 school buses during normal driving routines, and aboard hybrid lead vehicles traveling in front of the monitored buses during 46 trips. Ordinary and partial least square regression models for PM2.5 onboard buses were created with and without control for roadway concentrations, which were also modeled. Predictors examined included ambient PM2.5 levels, ambient weather, and bus and route characteristics. Concentrations aboard school buses (21 μg/m3) were four and two-times higher than ambient and roadway levels, respectively. Differences in PM2.5 levels between the buses and lead vehicles indicated an average of 7 μg/m3 originating from the bus's own emission sources. While roadway concentrations were dominated by ambient PM2.5, bus concentrations were influenced by bus age, diesel oxidative catalysts, and roadway concentrations. Cross validation confirmed the roadway models but the bus models were less robust. These results confirm that children are exposed to air pollution from the bus and other roadway traffic while riding school buses. In-cabin air pollution is higher than roadway concentrations and is likely influenced by bus characteristics. PMID:18985175

Predicting airborne particle levels aboard Washington State school buses

NASA Astrophysics Data System (ADS)

Adar, Sara D.; Davey, Mark; Sullivan, James R.; Compher, Michael; Szpiro, Adam; Sally Liu, L.-J.

School buses contribute substantially to childhood air pollution exposures yet they are rarely quantified in epidemiology studies. This paper characterizes fine particulate matter (PM 2.5) aboard school buses as part of a larger study examining the respiratory health impacts of emission reducing retrofits. To assess onboard concentrations, continuous PM 2.5 data were collected during 85 trips aboard 43 school buses during normal driving routines, and aboard hybrid lead vehicles traveling in front of the monitored buses during 46 trips. Ordinary and partial least squares regression models for PM 2.5 onboard buses were created with and without control for roadway concentrations, which were also modeled. Predictors examined included ambient PM 2.5 levels, ambient weather, and bus and route characteristics. Average concentrations aboard school buses (21 μg m -3) were four and two-times higher than ambient and roadway levels, respectively. Differences in PM 2.5 levels between the buses and lead vehicles indicated an average of 7 μg m -3 originating from the bus's own emission sources. While roadway concentrations were dominated by ambient PM 2.5, bus concentrations were influenced by bus age, diesel oxidative catalysts, and roadway concentrations. Cross-validation confirmed the roadway models but the bus models were less robust. These results confirm that children are exposed to air pollution from the bus and other roadway traffic while riding school buses. In-cabin air pollution is higher than roadway concentrations and is likely influenced by bus characteristics.

Bus drivers' exposure to bullying at work: an occupation-specific approach.

PubMed

Glasø, Lars; Bele, Edvard; Nielsen, Morten Birkeland; Einarsen, Ståle

2011-10-01

The present study employs an occupation-specific approach to examine bus drivers' exposure to bullying and their trait anger, job engagement, job satisfaction and turnover intentions. A total of 1,023 bus drivers from a large public transport organization participated in the study. The findings show that bus driving can be a high risk occupation with regard to bullying, since 70% of the bus drivers had experienced one or more acts typical of bullying during the last six months. As many as 11% defined themselves as victims of bullying, 33% of whom (i.e. 3.6% of the total sample) see themselves as victims of frequent bullying. Colleagues were most frequently reported as perpetrators. Exposure to bullying was negatively related to job engagement and job satisfaction and positively related to turnover intentions. Job engagement and job satisfaction mediated the relationship between bullying and intention to leave, respectively. Trait anger had an interaction effect on the relationship between bullying and turnover intentions. This study indicates that workplace bullying has context-specific aspects that require increased use of context-specific policies and intervention methods. © 2011 The Authors. Scandinavian Journal of Psychology © 2011 The Scandinavian Psychological Associations.

Fatigue factors affecting metropolitan bus drivers: a qualitative investigation.

PubMed

Biggs, Herbert; Dingsdag, Donald; Stenson, Nick

2009-01-01

Metropolitan bus drivers daily face work in a stressful and draining work environment, exposing them to the serious risk of driver fatigue. However, there has been a dearth of information exploring the unique antecedents and effects of such fatigue. To date, much of the research into metropolitan bus drivers has been under the umbrella of large heavy vehicle driving studies, which include a disproportionally large population of long-haul drivers, who are likely to face a significantly different set of fatigue factors [1]. The present study aimed to investigate which work and environmental factors may cause fatigue in metropolitan bus drivers by seeking drivers' own perspectives on the issues. To this end, focus groups were held at five bus depots in Sydney and Newcastle, with an effort made to include a stratified sample of drivers at each. Each of the groups were invited to nominate what factors they felt were most salient, with a number of common factors emerging across the depots. Key themes identified were: support from management; ticketing and related issues; interaction with passengers; cabin ergonomics; tight route schedules; turn-around and shift irregularity; extended shift cycles; interactions with other road users; and extended commute times.

77 FR 35718 - Certain Universal Serial Bus (“USB”) Portable Storage Devices, Including USB Flash Drives and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-14

... on the Commission's electronic docket (EDIS) at http://edis.usitc.gov . Hearing-impaired persons are... Sunnyvale, California; Kingston Technology Company, Inc. of Fountain Valley, California; Patriot Memory, LLC...

Truck and bus driver task analysis

DOT National Transportation Integrated Search

1973-05-01

This report describes the tasks involved in driving large trucks and buses. The task descriptions are an extension of the task description developed by Human Resources Research Organization (HumRRO) for passenger car drivers and deal with those uniqu...

Advanced Computational Models for Fabric-Reinforced Composites

DTIC Science & Technology

2001-10-01

composites. Trans-Science Corporation 3655 Nobel Drive Suite 440 San Diego, CA 92122-1005 Tel (858) 459-1240 http://www.compositesolutionsinc.com...also based in XP! Material Suppliers San Diego, recently developed the only Newsletters comprehensive design software for the seismic NDT, NDE , NDI...composite bus. Trans-Science Corporation 3655 Nobel Drive Suite 440 San Diego, CA 92122-1005 Tel (858) 459-1240 Fax (858) 459-0210 •’(S-HOME SERVICES

Directions & Parking | Cancer Prevention Fellowship Program

Cancer.gov

For up-to-date information on public transportation (metrorail, shuttle services, and bus routes view the Visitor Information page at NCI.  Driving Directions There are ample parking spaces in the NCI Shady Grove parking garage, and parking is free.

Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

PubMed

Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

2015-01-01

Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

Proton exchange membrane fuel cell system diagnosis based on the signed directed graph method

NASA Astrophysics Data System (ADS)

Hua, Jianfeng; Lu, Languang; Ouyang, Minggao; Li, Jianqiu; Xu, Liangfei

The fuel-cell powered bus is becoming the favored choice for electric vehicles because of its extended driving range, zero emissions, and high energy conversion efficiency when compared with battery-operated electric vehicles. In China, a demonstration program for the fuel cell bus fleet operated at the Beijing Olympics in 2008 and the Shanghai Expo in 2010. It is necessary to develop comprehensive proton exchange membrane fuel cell (PEMFC) diagnostic tools to increase the reliability of these systems. It is especially critical for fuel-cell city buses serving large numbers of passengers using public transportation. This paper presents a diagnostic analysis and implementation study based on the signed directed graph (SDG) method for the fuel-cell system. This diagnostic system was successfully implemented in the fuel-cell bus fleet at the Shanghai Expo in 2010.

Economic Optimization Analysis of Chengdu Electric Community Bus Operation

NASA Astrophysics Data System (ADS)

Yidong, Wang; Yun, Cai; Zhengping, Tan; Xiong, Wan

2018-03-01

In recent years, the government has strongly supported and promoted electric vehicles and has given priority to demonstration and popularization in the field of public transport. The economy of public transport operations has drawn increasing attention. In this paper, Chengdu wireless charging pure electric community bus is used as the research object, the battery, air conditioning, driver’s driving behavior and other economic influence factors were analyzed, and optimizing the operation plan through case data analysis, through the reasonable battery matching and mode of operation to help businesses effectively save operating costs and enhance economic efficiency.

Simulation of Trolleybus Traction Induction Drive With Supercapacitor Energy Storage System

NASA Astrophysics Data System (ADS)

Brazis, V.; Latkovskis, L.; Grigans, L.

2010-01-01

The article considers the possibilities of saving the regenerative braking energy in Škoda 24Tr type trolleybuses by installing the onboard supercapacitor energy storage system (ESS) and improving its performance with automated switching to the autonomous traction mode. Proposed is an ESS control system with constant DC bus voltage in the supercapacitor charging mode and supercapacitor current proportional to the AC drive current in the discharging mode. The authors investigate stability of the trolleybus ESS control system operating together with AC traction drive in various overhead voltage failure modes. The co-simulation of ESS operation was done by Matlab/Simulink AC drive and PSIM ESS continuous models.

Effect of Torsional Fastener Resistance on the Lateral Response of a Rail-Tie Structure

DOT National Transportation Integrated Search

1978-09-01

This report describes the results of a Transportation Systems Center investigation conducted under Urban Mass Transportation Administration sponsorship, of the practicality of a flywheel/diesel hybrid power drive for urban transit bus propulsion. The...

Rome Laboratory Journal, 1992

DTIC Science & Technology

1992-01-01

89 Suryadevara V. Babu, Raghunath Padiyath, Moses David. and Lois Walsh THREE-DIMENSIONAL MULTIREGION Sa SOLUTIONS OF THE...is built by simple sm -RC time constant analysis of thle buts, then thle discrete im- inispection of the bus and then itiverted to produice the driving

Teacher Tax Tips.

ERIC Educational Resources Information Center

Freeman, Paul

1979-01-01

Discusses income tax deductions for vocational agriculture teachers for expenses incurred through automobiles used for school business, course work expenses, professional dues, classroom supplies, books, cost of bus driving license, liability insurance, and special clothing. A specific example for claiming the deductions on an automobile is…

Low power, scalable multichannel high voltage controller

DOEpatents

Stamps, James Frederick [Livermore, CA; Crocker, Robert Ward [Fremont, CA; Yee, Daniel Dadwa [Dublin, CA; Dils, David Wright [Fort Worth, TX

2006-03-14

A low voltage control circuit is provided for individually controlling high voltage power provided over bus lines to a multitude of interconnected loads. An example of a load is a drive for capillary channels in a microfluidic system. Control is distributed from a central high voltage circuit, rather than using a number of large expensive central high voltage circuits to enable reducing circuit size and cost. Voltage is distributed to each individual load and controlled using a number of high voltage controller channel switches connected to high voltage bus lines. The channel switches each include complementary pull up and pull down photo isolator relays with photo isolator switching controlled from the central high voltage circuit to provide a desired bus line voltage. Switching of the photo isolator relays is further controlled in each channel switch using feedback from a resistor divider circuit to maintain the bus voltage swing within desired limits. Current sensing is provided using a switched resistive load in each channel switch, with switching of the resistive loads controlled from the central high voltage circuit.

Low power, scalable multichannel high voltage controller

DOEpatents

Stamps, James Frederick [Livermore, CA; Crocker, Robert Ward [Fremont, CA; Yee, Daniel Dadwa [Dublin, CA; Dils, David Wright [Fort Worth, TX

2008-03-25

A low voltage control circuit is provided for individually controlling high voltage power provided over bus lines to a multitude of interconnected loads. An example of a load is a drive for capillary channels in a microfluidic system. Control is distributed from a central high voltage circuit, rather than using a number of large expensive central high voltage circuits to enable reducing circuit size and cost. Voltage is distributed to each individual load and controlled using a number of high voltage controller channel switches connected to high voltage bus lines. The channel switches each include complementary pull up and pull down photo isolator relays with photo isolator switching controlled from the central high voltage circuit to provide a desired bus line voltage. Switching of the photo isolator relays is further controlled in each channel switch using feedback from a resistor divider circuit to maintain the bus voltage swing within desired limits. Current sensing is provided using a switched resistive load in each channel switch, with switching of the resistive loads controlled from the central high voltage circuit.

Explicit Nonlinear Finite Element Geometric Analysis of Parabolic Leaf Springs under Various Loads

PubMed Central

Kong, Y. S.; Omar, M. Z.; Chua, L. B.; Abdullah, S.

2013-01-01

This study describes the effects of bounce, brake, and roll behavior of a bus toward its leaf spring suspension systems. Parabolic leaf springs are designed based on vertical deflection and stress; however, loads are practically derived from various modes especially under harsh road drives or emergency braking. Parabolic leaf springs must sustain these loads without failing to ensure bus and passenger safety. In this study, the explicit nonlinear dynamic finite element (FE) method is implemented because of the complexity of experimental testing A series of load cases; namely, vertical push, wind-up, and suspension roll are introduced for the simulations. The vertical stiffness of the parabolic leaf springs is related to the vehicle load-carrying capability, whereas the wind-up stiffness is associated with vehicle braking. The roll stiffness of the parabolic leaf springs is correlated with the vehicle roll stability. To obtain a better bus performance, two new parabolic leaf spring designs are proposed and simulated. The stress level during the loadings is observed and compared with its design limit. Results indicate that the newly designed high vertical stiffness parabolic spring provides the bus a greater roll stability and a lower stress value compared with the original design. Bus safety and stability is promoted, as well as the load carrying capability. PMID:24298209

Explicit nonlinear finite element geometric analysis of parabolic leaf springs under various loads.

PubMed

Kong, Y S; Omar, M Z; Chua, L B; Abdullah, S

2013-01-01

This study describes the effects of bounce, brake, and roll behavior of a bus toward its leaf spring suspension systems. Parabolic leaf springs are designed based on vertical deflection and stress; however, loads are practically derived from various modes especially under harsh road drives or emergency braking. Parabolic leaf springs must sustain these loads without failing to ensure bus and passenger safety. In this study, the explicit nonlinear dynamic finite element (FE) method is implemented because of the complexity of experimental testing A series of load cases; namely, vertical push, wind-up, and suspension roll are introduced for the simulations. The vertical stiffness of the parabolic leaf springs is related to the vehicle load-carrying capability, whereas the wind-up stiffness is associated with vehicle braking. The roll stiffness of the parabolic leaf springs is correlated with the vehicle roll stability. To obtain a better bus performance, two new parabolic leaf spring designs are proposed and simulated. The stress level during the loadings is observed and compared with its design limit. Results indicate that the newly designed high vertical stiffness parabolic spring provides the bus a greater roll stability and a lower stress value compared with the original design. Bus safety and stability is promoted, as well as the load carrying capability.

Integrated chassis control for a three-axle electric bus with distributed driving motors and active rear steering system

NASA Astrophysics Data System (ADS)

Liu, Wei; He, Hongwen; Sun, Fengchun; Lv, Jiangyi

2017-05-01

This paper describes an integrated chassis control framework for a novel three-axle electric bus with active rear steering (ARS) axle and four motors at the middle and rear wheels. The proposed integrated framework consists of four parts: (1) an active speed limiting controller is designed for anti-body slip control and rollover prevention; (2) an ARS controller is designed for coordinating the tyre wear between the driving wheels; (3) an inter-axle torque distribution controller is designed for optimal torque distribution between the axles, considering anti-wheel slip and battery power limitations and (4) a data acquisition and estimation module for collecting the measured and estimated vehicle states. To verify the performances, a simulation platform is established in Trucksim software combined with Simulink. Three test cases are particularly designed to show the performances. The proposed algorithm is compared with a simple even control algorithm. The test results show satisfactory lateral stability and rollover prevention performances under severe steering conditions. The desired tyre wear coordinating performance is also realised, and the wheel slip ratios are restricted within stable region during intensive driving and emergency braking with complicated road conditions.

Feasibility assessment of the use of transit bus driving simulators : final report.

DOT National Transportation Integrated Search

2000-04-07

The purpose of this document is to present state-level statistics for the CVISN deployment described in the national report. These data will allow state stakeholders to evaluate their own deployment standings in relation to national averages. The nat...

Bus operators' responses to job strain: An experimental test of the job demand-control model.

PubMed

Cendales-Ayala, Boris; Useche, Sergio Alejandro; Gómez-Ortiz, Viviola; Bocarejo, Juan Pablo

2017-10-01

The research aim was to test the Job Demand-Control (JDC) Model demands × Control interaction (or buffering) hypothesis in a simulated bus driving experiment. The buffering hypothesis was tested using a 2 (low and high demands) × 2 (low and high decision latitude) design with repeated measures on the second factor. A sample of 80 bus operators were randomly assigned to the low (n = 40) and high demands (n = 40) conditions. Demands were manipulated by increasing or reducing the number of stops to pick up passengers, and decision latitude by imposing or removing restrictions on the Rapid Transit Bus (BRT) operators' pace of work. Outcome variables include physiological markers (heart rate [HR], heart rate variability [HRV], breathing rate [BR], electromyography [EMG], and skin conductance [SC]), objective driving performance and self-report measurements of psychological wellbeing (psychological distress, interest/enjoyment [I/E], perceived competence, effort/importance [E/I], and pressure/tension [P/T]). It was found that job decision latitude moderates the effect of job demands on both physiological arousal (BR: F(1, 74) = 4.680, p = .034, SC: F(1, 75) = 6.769, p = .011, and EMG: F(1, 75) = 6.550, p = .013) and psychological well-being (P/T: F(1, 75) = 4.289, p = .042 and I/E: F(1, 74) = 4.548, p = .036). Consistently with the JDC model buffering hypothesis, the experimental findings suggest that increasing job decision latitude can moderate the negative effect of job demands on different psychophysiological outcomes. This finding is useful for designing organizational and clinical interventions in an occupational group at high risk of work stress-related disease. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Relationships of working conditions, health problems and vehicle accidents in bus rapid transit (BRT) drivers.

PubMed

Gómez-Ortiz, Viviola; Cendales, Boris; Useche, Sergio; Bocarejo, Juan P

2018-04-01

The aim of this study was to estimate accident risk rates and mental health of bus rapid transit (BRT) drivers based on psychosocial risk factors at work leading to increased stress and health problems. A cross-sectional research design utilized a self-report questionnaire completed by 524 BRT drivers. Some working conditions of BRT drivers (lack of social support from supervisors and perceived potential for risk) may partially explain Bogota's BRT drivers' involvement in road accidents. Drivers' mental health problems were associated with higher job strain, less support from co-workers, fewer rewards and greater signal conflict while driving. To prevent bus accidents, supervisory support may need to be increased. To prevent mental health problems, other interventions may be needed such as reducing demands, increasing job control, reducing amount of incoming information, simplifying current signals, making signals less contradictory, and revising rewards. © 2018 Wiley Periodicals, Inc.

Risk factors for unintentional occupational injury among urban transit bus drivers: a cohort longitudinal study.

PubMed

Wei, Chia; Gerberich, Susan G; Ryan, Andrew D; Alexander, Bruce H; Church, Timothy R; Manser, Michael

2017-12-01

Although many studies have focused on bus operators' occupational diseases, work-related injury and associated risk factor data are limited. The purpose of this longitudinal study was to investigate unintentional injury and exposures that may affect injury risk among metropolitan bus operators. Demographic, work-related, and injury data obtained from a metropolitan transit company for a 5-year period, enabled estimates of rates per 100 full time equivalents (FTEs) and adjusted Hazard Ratios (HRs), with 95% confidence intervals (CIs), using Generalized Estimating Equations and Cox proportional hazards models, respectively. The 2095 bus operators, included in this study, had an unintentional injury rate (95% CI) of 17.8 (16.1-19.7) per 100 FTEs. Multivariable analysis identified increased risks for operators who were female, compared to male (HR = 2.4; 2.0-2.8); worked less than 7 versus 7 to less than 12 hours per day (HR = 4.6; 3.8-5.5); and drove less than 7 versus 7 to less than 12 hours per day (HR = 3.2; 2.7-3.8). Suggestive increased risks were identified for operators working split versus straight shifts (HR = 1.2; 1.0-1.4) and for driving limited versus regular bus routes (HR = 1.36; 1.0-1.8). Results serve as a basis for further studies and inform the development of targeted intervention strategies to reduce bus operators' occupational injuries. Copyright © 2017 Elsevier Inc. All rights reserved.

Urinary 1-hydroxypyrene and mutagenicity in bus drivers and mail carriers exposed to urban air pollution in Denmark.

PubMed

Hansen, Ase Marie; Wallin, Håkan; Binderup, Mona Lise; Dybdahl, Marianne; Autrup, Herman; Loft, Steffen; Knudsen, Lisbeth Ehlert

2004-01-10

Previous studies in Denmark have shown that bus drivers and tramway employees were at an increased risk for developing several types of cancer and that bus drives from central Copenhagen have high levels of biomarkers of DNA damage. The present study evaluates 1-hydroxypyrene concentrations and mutagenic activity in urine as biomarkers of exposure in non-smoking bus drivers in city and rural areas on a work day and a day off and in non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). Twenty-four hour urine samples were collected on a working day and a day off from 60 non-smoking bus drivers in city and rural areas and from 88 non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). The concentration of 1-hydroxypyrene was measured by means of HPLC and the mutagenic activity was assessed by the Ames assay with Salmonella tester strain YG1021 and S9 mix. The N-acetyltransferase (NAT2) phenotype was used as a biomarker for susceptibility to mutagenic/carcinogenic compounds. Bus drivers excreted more 1-hydroxypyrene in urine than did mail carriers. The differences were slightly smaller when NAT2 phenotype, cooking at home, exposure to vehicle exhaust, and performing physical exercise after work were included. The NAT2 slow acetylators had 29% (1.29 [CI: 1.15-1.98]) higher 1-hydroxypyrene concentrations in urine than the fast acetylators. Male bus drivers had 0.92 revertants/mol creatinine [CI: 0.37-1.47] and female bus drivers 1.90 revertants/mol creatinine [CI: 1.01-2.79] higher mutagenic activity in urine than mail carriers. The present study indicates that bus drivers are more exposed to polycyclic aromatic hydrocarbons (PAH) and mutagens than mail carriers. Mail carriers who worked outdoors had higher urinary concentration of 1-hydroxypyrene, a marker of exposure to PAH, than those working indoors. The individual levels of urinary mutagenic activity were not correlated to excretion of 1-hydroxypyrene. This might be due to the fact that the most potent mutagenic compounds in diesel exhaust are not PAH but dinitro-pyrenes. Among bus drivers, fast NAT2 acetylators had higher mutagenic activity in urine than slow NAT2 acetylators and female bus drivers had higher mutagenic activity than male bus drivers.

Further validation of artificial neural network-based emissions simulation models for conventional and hybrid electric vehicles.

PubMed

Tóth-Nagy, Csaba; Conley, John J; Jarrett, Ronald P; Clark, Nigel N

2006-07-01

With the advent of hybrid electric vehicles, computer-based vehicle simulation becomes more useful to the engineer and designer trying to optimize the complex combination of control strategy, power plant, drive train, vehicle, and driving conditions. With the desire to incorporate emissions as a design criterion, researchers at West Virginia University have developed artificial neural network (ANN) models for predicting emissions from heavy-duty vehicles. The ANN models were trained on engine and exhaust emissions data collected from transient dynamometer tests of heavy-duty diesel engines then used to predict emissions based on engine speed and torque data from simulated operation of a tractor truck and hybrid electric bus. Simulated vehicle operation was performed with the ADVISOR software package. Predicted emissions (carbon dioxide [CO2] and oxides of nitrogen [NO(x)]) were then compared with actual emissions data collected from chassis dynamometer tests of similar vehicles. This paper expands on previous research to include different driving cycles for the hybrid electric bus and varying weights of the conventional truck. Results showed that different hybrid control strategies had a significant effect on engine behavior (and, thus, emissions) and may affect emissions during different driving cycles. The ANN models underpredicted emissions of CO2 and NO(x) in the case of a class-8 truck but were more accurate as the truck weight increased.

The effects of in-vehicle tasks and time-gap selection while reclaiming control from adaptive cruise control (ACC) with bus simulator.

PubMed

Lin, Tsang-Wei; Hwang, Sheue-Ling; Su, Jau-Ming; Chen, Wan-Hui

2008-05-01

This research aimed to find out the effects of in-vehicle distractions and time-gap settings with a fix-based bus driving simulator in a following scenario. Professional bus drivers were recruited to perform in-vehicle tasks while driving with adaptive cruise control (ACC) of changeable time-gap settings in freeway traffic. Thirty subjects were divided equally into three groups for different in-vehicle task modes (between subjects), including no task distraction, hands-free, and manual modes. Further, time-gap settings for the experimental ACC were: shorter than 1.0 s, 1.0-1.5 s, 1.5-2.0 s, and longer than 2.0 s (within subjects). Longitudinal (mean headway, forward collision rate, and response time) and lateral control (mean lateral lane position and its standard deviation) performance was assessed. In the results, longitudinal control performance was worsened by both shorter time-gaps and heavier in-vehicle tasks. But the interaction indicated that the harm by heavier in-vehicle distraction could be improved by longer time-gaps. As for the lateral control, it would only be negatively affected by shorter time-gap settings. This research indicates the effects of time-gaps and in-vehicle distraction, as well as the interaction. Proper time-gap selection under different in-vehicle distractions can help avoid accidents and keep safe.

Particulates and noise exposure during bicycle, bus and car commuting: A study in three European cities.

PubMed

Okokon, Enembe O; Yli-Tuomi, Tarja; Turunen, Anu W; Taimisto, Pekka; Pennanen, Arto; Vouitsis, Ilias; Samaras, Zissis; Voogt, Marita; Keuken, Menno; Lanki, Timo

2017-04-01

In order to curb traffic-related air pollution and its impact on the physical environment, contemporary city commuters are encouraged to shift from private car use to active or public transport modes. However, personal exposures to particulate matter (PM), black carbon and noise during commuting may be substantial. Therefore, studies comparing exposures during recommended modes of transport versus car trips are needed. We measured personal exposure to various-sized particulates, soot, and noise during commuting by bicycle, bus and car in three European cities: Helsinki in Finland, Rotterdam in the Netherlands and Thessaloniki in Greece using portable monitoring devices. We monitored commonly travelled routes in these cities. The total number of one-way trips yielding data on any of the measured parameters were 84, 72, 94 and 69 for bicycle, bus, closed-window car and open-window car modes, respectively. The highest mean PM 2.5 (85µg/m 3 ), PM 10 (131µg/m 3 ), black carbon (10.9µg/m 3 ) and noise (75dBA) levels were recorded on the bus, bus (again), open-window car and bicycle modes, respectively, all in Thessaloniki, PM and soot concentrations were generally higher during biking and taking a bus than during a drive in a a car with closed windows. Ratios of bike:car PM 10 ranged from 1.1 in Thessaloniki to 2.6 in Helsinki, while bus:car ratios ranged from in 1.0 in Rotterdam to 5.6 in Thessaloniki. Higher noise levels were mostly recorded during bicycle rides. Based on our study, active- and public-transport commuters are often at risk of higher air pollution and noise exposure than private car users. This should be taken into account in urban transportation planning. Copyright © 2017 Elsevier Inc. All rights reserved.

Exposure to particles and nitrogen dioxide among taxi, bus and lorry drivers.

PubMed

Lewné, Marie; Nise, Gun; Lind, Marie-Louise; Gustavsson, Per

2006-03-01

The aims of this study have been to investigate the occurrence of systematic differences in the personal exposure to motor exhaust between different groups of taxi, bus and lorry drivers, and to study if these are influenced by the choice of exposure indicator. We used one indicator of the gaseous phase, nitrogen dioxide (NO(2)), and one of the particle phase (measured by DataRAM), of the exhausts. A total of 121 drivers were included in the study: 39 taxi drivers, 42 bus drivers and 40 lorry drivers. Personal measurements were performed during one working day. Nitrogen dioxide was measured with passive diffusive samplers and particles with Data-RAM, a logging instrument using nephelometric monitoring. The instrument measures particles between 0.1 and 10 microm in size. The average exposure to NO(2) for lorry drivers was 68 microg/m(3); for bus drivers 60 microg/m(3) and for taxi drivers 48 microg/m(3). For particles the exposure was 57 microg/m(3) for lorry drivers, 44 microg/m(3) for bus drivers and 26 microg/m(3) for taxi drivers. The result remained unchanged when exposures were adjusted for variation in urban background levels of NO(2) and particulate matter with an aerodynamic diameter <10 microm (PM(10)). Lorry drivers experienced the highest exposure and taxi drivers the lowest with bus drivers in an intermediate position, regardless of whether NO(2) or particles were used as exposure indicator. The levels of both NO(2) and particles were higher for bus drivers in the city than for them driving in the suburbs. Using diesel or petrol as a fuel for taxis had no influence on the exposure for the drivers, indicating that the taxi drivers' exposure mainly depends on exhaust from surrounding traffic.

Method and system for managing an electrical output of a turbogenerator

DOEpatents

Stahlhut, Ronnie Dean; Vuk, Carl Thomas

2009-06-02

The system and method manages an electrical output of a turbogenerator in accordance with multiple modes. In a first mode, a direct current (DC) bus receives power from a turbogenerator output via a rectifier where turbogenerator revolutions per unit time (e.g., revolutions per minute (RPM)) or an electrical output level of a turbogenerator output meet or exceed a minimum threshold. In a second mode, if the turbogenerator revolutions per unit time or electrical output level of a turbogenerator output are less than the minimum threshold, the electric drive motor or a generator mechanically powered by the engine provides electrical energy to the direct current bus.

Method and apparatus for controlling a microturbine

DOEpatents

Garces, Luis Jose; Cardinal, Mark Edward; Sinha, Gautam; Dame, Mark Edward

2005-08-02

An apparatus for controlling a microturbine, the apparatus including: a rectifier adapted for converting at least one generated voltage from the microturbine to a DC link voltage; an inverter adapted for converting the DC link voltage to at least one inverter output voltage, the at least one inverter output voltage being electrically coupled to an external power bus; a starter drive adapted for converting at least one starter input voltage to at least one starter output voltage, the at least one starter input voltage being electrically coupled to the external power bus, the at least one starter output voltage being electrically coupled to the microturbine.

Method and system for managing an electrical output of a turbogenerator

DOEpatents

Stahlhut, Ronnie Dean; Vuk, Carl Thomas

2010-08-24

The system and method manages an electrical output of a turbogenerator in accordance with multiple modes. In a first mode, a direct current (DC) bus receives power from a turbogenerator output via a rectifier where turbogenerator revolutions per unit time (e.g., revolutions per minute (RPM)) or an electrical output level of a turbogenerator output meet or exceed a minimum threshold. In a second mode, if the turbogenerator revolutions per unit time or electrical output level of a turbogenerator output are less than the minimum threshold, the electric drive motor or a generator mechanically powered by the engine provides electrical energy to the direct current bus.

Optimal bus temperature for thermal comfort during a cool day.

PubMed

Velt, K B; Daanen, H A M

2017-07-01

A challenge for electric buses is to minimize heating and cooling power to maximally extend the driving range, but still provide sufficient thermal comfort for the driver and passengers. Therefore, we investigated the thermal sensation (TS) and thermal comfort (TC) of passengers in buses during a cool day (temperature 13.4 ± 0.5 °C, relative humidity (RH) 60 ± 5.8%) typical for the Dutch temperate maritime climate. 28 Males and 72 females rated TS and TC and gave information on age, stature, body weight and worn garments. The temperature in the bus of 22.5 ± 1.1 °C and RH of 59.9 ± 5.8% corresponded to a slightly warm feeling (TS = 0.85 ± 1.06) and TC of 0.39 ± 0.65. TS related significantly to bus temperature, clothing insulation and age. Linear regression based on these parameters showed that the temperature in the bus corresponding to TC = 0 and TS = 0 would have been 20.9 ± 0.6 °C. In conclusion, a 1.6 °C lower bus temperature during the investigated cool day probably would have led to less thermal discomfort and energy savings of electrical busses. The methodology to relate climatic measurements to subjective assessments is currently employed in a wider climatic range and may prove to be useful to find a better balance between thermal comfort and energy savings of the bus. Copyright © 2017 Elsevier Ltd. All rights reserved.

Alcohol, Drugs and Driving: Implications for Evaluating Driver Impairment

PubMed Central

Brown, Timothy; Milavetz, Gary; Murry, Daryl J.

2013-01-01

Impaired driving is a significant traffic safety problem, and alcohol and drugs taken before driving contribute substantially to this problem. With the increase in use of prescription medication and the decriminalization of some drugs, it has become increasingly important to understand the manifestation of driver impairment. Building upon previous alcohol research conducted at the National Advanced Driving Simulator (NADS), this study enrolled commercial bus drivers to evaluate the effect of triazolam on driving performance to assess difference between placebo, 0.125, and 0.25 mg doses in a randomized and double-blind design. On each of three randomized visits, subjects drove a simulator scenario that had previously been used to demonstrate effects of alcohol on driving performance. Plasma triazolam levels were obtained before the simulator drive. The protocol included participants receiving study medication and placebo over a 3-week period of time one to two weeks apart. The simulator drives used for this analysis occurred approximately 140 minutes after dosing—after the subjects had completed four bus simulator drives and neuropsychological tests over a 2-hour period of time surrounding dosing. The driving scenario contained representative situations on three types of roadways (urban, freeway, and rural) under nighttime driving conditions. Lane keeping performance (ability to drive straight in the lane) under the three doses of triazolam demonstrates that at the 0.25 mg dose, statistically significant effects on performance are observed, but no effects are found at the 0.125 mg level when testing at this time period after dosing. This differs from the effects of alcohol, which shows impairing effects at a 0.05% blood alcohol concentration (BAC) and a greater effect at 0.10% BAC. These results demonstrate the importance of understanding how different types of drugs affect driving performance in realistic driving environments. Although some compounds may have an effect that correlates linearly to dosage, that is not always the case. An understanding of these differences and how they vary across driving tasks is essential to developing a robust evaluation protocol that can accurately describe the effects of a wide variety of drugs on driver impairment. This information can be used to reduce the risk of deleterious effects of therapeutic medications while ensuring their safe and beneficial use. PMID:24406943

Problems Encountered During the Recertification of the GLORY Solar Array Dual Axis Gimbal Drive Actuators

NASA Technical Reports Server (NTRS)

Saltzman, Marc; Schepis, Jospeh P.; Bruckner, Michael J.

2009-01-01

The Glory observatory is the current incarnation of the Vegetation Canopy Lidar (VCL) mission spacecraft bus. The VCL spacecraft bus, having been cancelled for programmatic reasons in 2000, was nearly integrated when it was put into storage for possible future use. The Glory mission was a suitable candidate for using this spacecraft and in 2006 an effort to recertify the two axis solar array gimbal drive after its extended storage was begun. What was expected to be a simple performance validation of the two dual axis gimbal stepper motors became a serious test, diagnosis and repair task once questions arose on the flight worthiness of the hardware. A significant test program logic flow was developed which identified decisions that could be made based on the results of individual recertification tests. Without disassembling the bi-axial gimbals, beginning with stepper motor threshold voltage measurements and relating these to powered drive torque measurements, both performed at the spacecraft integrator s facility, a confusing picture of the health of the actuators came to light. Tests at the gimbal assembly level and tests of the disassembled actuators were performed by the manufacturer to validate our results and torque discrepancies were noted. Further disassembly to the component level of the actuator revealed the source of the torque loss.

Personal exposure to fine particulate air pollution while commuting: An examination of six transport modes on an urban arterial roadway.

PubMed

Chaney, Robert A; Sloan, Chantel D; Cooper, Victoria C; Robinson, Daniel R; Hendrickson, Nathan R; McCord, Tyler A; Johnston, James D

2017-01-01

Traffic-related air pollution in urban areas contributes significantly to commuters' daily PM2.5 exposures, but varies widely depending on mode of commuting. To date, studies show conflicting results for PM2.5 exposures based on mode of commuting, and few studies compare multiple modes of transportation simultaneously along a common route, making inter-modal comparisons difficult. In this study, we examined breathing zone PM2.5 exposures for six different modes of commuting (bicycle, walking, driving with windows open and closed, bus, and light-rail train) simultaneously on a single 2.7 km (1.68 mile) arterial urban route in Salt Lake City, Utah (USA) during peak "rush hour" times. Using previously published minute ventilation rates, we estimated the inhaled dose and exposure rate for each mode of commuting. Mean PM2.5 concentrations ranged from 5.20 μg/m3 for driving with windows closed to 15.21 μg/m3 for driving with windows open. The estimated inhaled doses over the 2.7 km route were 6.83 μg for walking, 2.78 μg for cycling, 1.28 μg for light-rail train, 1.24 μg for driving with windows open, 1.23 μg for bus, and 0.32 μg for driving with windows closed. Similarly, the exposure rates were highest for cycling (18.0 μg/hr) and walking (16.8 μg/hr), and lowest for driving with windows closed (3.7 μg/hr). Our findings support previous studies showing that active commuters receive a greater PM2.5 dose and have higher rates of exposure than commuters using automobiles or public transportation. Our findings also support previous studies showing that driving with windows closed is protective against traffic-related PM2.5 exposure.

Personal exposure to fine particulate air pollution while commuting: An examination of six transport modes on an urban arterial roadway

PubMed Central

Sloan, Chantel D.; Cooper, Victoria C.; Robinson, Daniel R.; Hendrickson, Nathan R.; McCord, Tyler A.; Johnston, James D.

2017-01-01

Traffic-related air pollution in urban areas contributes significantly to commuters’ daily PM2.5 exposures, but varies widely depending on mode of commuting. To date, studies show conflicting results for PM2.5 exposures based on mode of commuting, and few studies compare multiple modes of transportation simultaneously along a common route, making inter-modal comparisons difficult. In this study, we examined breathing zone PM2.5 exposures for six different modes of commuting (bicycle, walking, driving with windows open and closed, bus, and light-rail train) simultaneously on a single 2.7 km (1.68 mile) arterial urban route in Salt Lake City, Utah (USA) during peak “rush hour” times. Using previously published minute ventilation rates, we estimated the inhaled dose and exposure rate for each mode of commuting. Mean PM2.5 concentrations ranged from 5.20 μg/m3 for driving with windows closed to 15.21 μg/m3 for driving with windows open. The estimated inhaled doses over the 2.7 km route were 6.83 μg for walking, 2.78 μg for cycling, 1.28 μg for light-rail train, 1.24 μg for driving with windows open, 1.23 μg for bus, and 0.32 μg for driving with windows closed. Similarly, the exposure rates were highest for cycling (18.0 μg/hr) and walking (16.8 μg/hr), and lowest for driving with windows closed (3.7 μg/hr). Our findings support previous studies showing that active commuters receive a greater PM2.5 dose and have higher rates of exposure than commuters using automobiles or public transportation. Our findings also support previous studies showing that driving with windows closed is protective against traffic-related PM2.5 exposure. PMID:29121096

Games in Geography.

ERIC Educational Resources Information Center

Walford, Rex

Six games designed for classroom use are described in this book: 1) Shopping Game; 2) Bus Service Game; 3) North Sea Gas Game; 4) Railway Pioneers Game; 5) Development Game; and 6) Export Drive Game. The description of each game comprises a separate chapter, and includes information about the general aims of the game, how the various game elements…

Turf Tales

ERIC Educational Resources Information Center

DiConsiglio, John

2009-01-01

When it comes to raising money for college and university athletic programs, every professional knows how the game is played. Tickets drive the bus. In exchange for gifts, donors typically pay seat-licensing fees. This kind of "quid pro quo" giving--where generous contributions put one in position to buy good tickets--is a very common model," says…

Steering Kids to Traffic Safety.

ERIC Educational Resources Information Center

PTA Today, 1991

1991-01-01

Guidelines to help parents explain traffic safety to children cover the following: school bus safety (e.g., remain seated, do not shout); walking (e.g., obey traffic signals, cross at crosswalks); driving (e.g., wear seatbelts, enter and exit from the curb side); and biking (e.g., wear helmets, do not ride at night). (SM)

[Reliability and validity of Driving Anger Scale in professional drivers in China].

PubMed

Li, Z; Yang, Y M; Zhang, C; Li, Y; Hu, J; Gao, L W; Zhou, Y X; Zhang, X J

2017-11-10

Objective: To assess the reliability and validity of the Chinese version of Driving Anger Scale (DAS) in professional drivers in China and provide a scientific basis for the application of the scale in drivers in China. Methods: Professional drivers, including taxi drivers, bus drivers, truck drivers and school bus drivers, were selected to complete the questionnaire. Cronbach's α and split-half reliability were calculated to evaluate the reliability of DAS, and content, contract, discriminant and convergent validity were performed to measure the validity of the scale. Results: The overall Cronbach's α of DAS was 0.934 and the split-half reliability was 0.874. The correlation coefficient of each subscale with the total scale was 0.639-0.922. The simplified version of DAS supported a presupposed six-factor structure, explaining 56.371% of the total variance revealed by exploratory factor analysis. The DAS had good convergent and discriminant validity, with the success rate of calibration experiment of 100%. Conclusion: DAS has a good reliability and validity in professional drivers in China, and the use of DAS is worth promoting in divers.

Evaluation of Traffic Accident Risk in In-City Bus Drivers: The Use of Berlin Questionnaire

PubMed Central

Ekren, Pervin Korkmaz; Uysal, Funda Elmas; Başoğlu, Özen K.

2018-01-01

OBJECTIVES Traffic accidents associated with high mortality rate may produce serious problems especially in highways. Obstructive sleep apnea (OSA) has been associated with a high risk for traffic accidents due to excessive daytime sleepiness even in in-city drivers. In the present study, it was aimed to evaluate the rate of OSA symptoms and to identify risk factors associated with traffic accidents in in-city bus drivers. MATERIAL AND METHODS A self-administered questionnaire including demographic and anthropometric features, sleep and work schedules, Berlin questionnaire, Epworth sleepiness score (ESS), and history of traffic accidents was used. RESULTS The questionnaire was conducted for 1400 male bus drivers (mean age, 38.0±6.4 y, body mass index, 27.8±3.9 kg/m2). A total of 1058 (75.6%) drivers had one or more accidents while driving bus. According to the Berlin questionnaire, 176 (12.6%) drivers were found to have high OSA risk and the accident rate was 83.0% in high-risk group, whereas 74.5% of low-risk drivers had accidents (p=0.043). The drivers with a history of traffic accident were older (p=0.030), had higher ESS (p=0.019), and were more in the high-risk OSA group according to the Berlin questionnaire (p=0.015). In multivariate linear regression analysis, traffic accident was associated with only Berlin questionnaire (p=0.015). CONCLUSION The present results support that city bus drivers with high OSA risk according to Berlin questionnaire have increased accident rates. Therefore, we suggest using Berlin questionnaire for screening sleep apnea not only in highway drivers but also in in-city bus drivers. PMID:29755810

Evaluation of Traffic Accident Risk in In-City Bus Drivers: The Use of Berlin Questionnaire.

PubMed

Taşbakan, Mehmet Sezai; Ekren, Pervin Korkmaz; Uysal, Funda Elmas; Başoğlu, Özen K

2018-04-01

Traffic accidents associated with high mortality rate may produce serious problems especially in highways. Obstructive sleep apnea (OSA) has been associated with a high risk for traffic accidents due to excessive daytime sleepiness even in in-city drivers. In the present study, it was aimed to evaluate the rate of OSA symptoms and to identify risk factors associated with traffic accidents in in-city bus drivers. A self-administered questionnaire including demographic and anthropometric features, sleep and work schedules, Berlin questionnaire, Epworth sleepiness score (ESS), and history of traffic accidents was used. The questionnaire was conducted for 1400 male bus drivers (mean age, 38.0±6.4 y, body mass index, 27.8±3.9 kg/m 2 ). A total of 1058 (75.6%) drivers had one or more accidents while driving bus. According to the Berlin questionnaire, 176 (12.6%) drivers were found to have high OSA risk and the accident rate was 83.0% in high-risk group, whereas 74.5% of low-risk drivers had accidents (p=0.043). The drivers with a history of traffic accident were older (p=0.030), had higher ESS (p=0.019), and were more in the high-risk OSA group according to the Berlin questionnaire (p=0.015). In multivariate linear regression analysis, traffic accident was associated with only Berlin questionnaire (p=0.015). The present results support that city bus drivers with high OSA risk according to Berlin questionnaire have increased accident rates. Therefore, we suggest using Berlin questionnaire for screening sleep apnea not only in highway drivers but also in in-city bus drivers.

Performance testing of EVs in the EPRI/TVA EV program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driggans, R.L.

1983-01-01

Performance testing has been completed on four electric vehicles: the Grumman-Olson Kubvan, SCT Electric (VW) Pickup, Jet Industries Electrica, and VW Electrotransporter Bus. The tests performed included vehicle dc energy consumption and driving range at constant speeds and on the SAE J227a C cycle, on-road driving range, hill climbing, maximum acceleration, top speed, and braking performance. Descriptions of the vehicles tested and comparisons of major performance parameters on all four vehicles are presented. This testing was performed at the TVA Electric Vehicle Test Facility.

Instrumentation & Data Acquisition System (D AS) Engineer

NASA Technical Reports Server (NTRS)

Jackson, Markus Deon

2015-01-01

The primary job of an Instrumentation and Data Acquisition System (DAS) Engineer is to properly measure physical phenomenon of hardware using appropriate instrumentation and DAS equipment designed to record data during a specified test of the hardware. A DAS system includes a CPU or processor, a data storage device such as a hard drive, a data communication bus such as Universal Serial Bus, software to control the DAS system processes like calibrations, recording of data and processing of data. It also includes signal conditioning amplifiers, and certain sensors for specified measurements. My internship responsibilities have included testing and adjusting Pacific Instruments Model 9355 signal conditioning amplifiers, writing and performing checkout procedures, writing and performing calibration procedures while learning the basics of instrumentation.

Speed limiter integrated fatigue analyzer (SLIFA) for speed and fatigue control on diesel engine truck and bus

NASA Astrophysics Data System (ADS)

Wahyudi, Haris; Pranoto, Hadi; Leman, A. M.; Sebayang, Darwin; Baba, I.

2017-09-01

Every second, the number of road traffic deaths is increased globally with millions more sustaining severe injuries and living with long-term adverse health consequences. Jakarta alone in year 2015 had recorded 556 people died due to road accidents, approximately reached 6.231 road accident cases. The identified major contributory factors of such unfortunate events are both driver fatigue and over speeding habit especially related to the driving of truck and bus. This paper presents the idea on how to control the electronic system from input fuel system of injection pump and the combustion chamber engine will control the valve solenoid in injection pump which can lock and fuel will stop for moment, and speed limit can be success, by using sensor heart rate we can input reduce speed limit when fatigue detection driver. Integration process this tool can be relevant when Speed Limiter Integrated Fatigue Analyser (SLIFA) trial in the diesel engine for truck and bus, the result of this research Speed Limiter Integrated Fatigue Analyser (SLIFA) able to control speed of diesel engine for truck and bus almost 30km/h, 60km/h, and until 70 km/h. The installation of the sensor heart rate as the input speed limit SLIFA would work when the driver is detected to be in the fatigue condition. We make Speed Limiter Integrated Fatigue Analyser (SLIFA) for control and monitoring system for diesel engine in truck and bus. Speed Limiter Integrated Fatigue Analyser (SLIFA) system can save the historical of the speed record, fatigue, rpm, and body temperature of the driver.

Electric vehicle system for charging and supplying electrical power

DOEpatents

Su, Gui Jia

2010-06-08

A power system that provides power between an energy storage device, an external charging-source/load, an onboard electrical power generator, and a vehicle drive shaft. The power system has at least one energy storage device electrically connected across a dc bus, at least one filter capacitor leg having at least one filter capacitor electrically connected across the dc bus, at least one power inverter/converter electrically connected across the dc bus, and at least one multiphase motor/generator having stator windings electrically connected at one end to form a neutral point and electrically connected on the other end to one of the power inverter/converters. A charging-sourcing selection socket is electrically connected to the neutral points and the external charging-source/load. At least one electronics controller is electrically connected to the charging-sourcing selection socket and at least one power inverter/converter. The switch legs in each of the inverter/converters selected by the charging-source/load socket collectively function as a single switch leg. The motor/generators function as an inductor.

Current limiting remote power control module

NASA Technical Reports Server (NTRS)

Hopkins, Douglas C.

1990-01-01

The power source for the Space Station Freedom will be fully utilized nearly all of the time. As such, any loads on the system will need to operate within expected limits. Should any load draw an inordinate amount of power, the bus voltage for the system may sag and disrupt the operation of other loads. To protect the bus and loads some type of power interface between the bus and each load must be provided. This interface is most crucial when load faults occur. A possible system configuration is presented. The proposed interface is the Current Limiting Remote Power Controller (CL-RPC). Such an interface should provide the following power functions: limit overloading and resulting undervoltage; prevent catastrophic failure and still provide for redundancy management within the load; minimize cable heating; and provide accurate current measurement. A functional block diagram of the power processing stage of a CL-RPC is included. There are four functions that drive the circuit design: rate control of current; current sensing; the variable conductance switch (VCS) technology; and the algorithm used for current limiting. Each function is discussed separately.

The universal serial bus endoscope: design and initial clinical experience.

PubMed

Hernandez-Zendejas, Gregorio; Dobke, Marek K; Guerrerosantos, Jose

2004-01-01

Endoscopic forehead lift is a well-established procedure in aesthetic plastic surgery. Many agree that currently available video-endoscopic equipment is bulky, multipieced and sometimes cumbersome in the operating theater. A novel system, the Universal Serial Bus Endoscope (USBE) was designed to simplify and reduce the number of necessary equipment pieces in the endoscopic setup. The USBE is attached by a single cable to a Universal Serial Bus (USB) port of a laptop computer. A built-in miniaturized cold light source provides illumination. A built-in digital camera chip enables procedure recording. The real-time images and movies obtained with USBE are displayed on the computer's screen and recorded on the laptop's hard disk drive. In this study, 25 patients underwent endoscopic browlift using the USBE system to test its clinical usefulness, all with good results and without complications or need for revision. The USBE was found to be reliable and easier to use than current video-endoscope equipment. The operative time needed to complete the procedure by the authors was reduced approximately 50%. The design and main technical characteristics of the USBE are presented.

Fuel cell drives for road vehicles

NASA Astrophysics Data System (ADS)

Charnah, R. M.

For fuel-cell driven vehicles, including buses, the fuel cell may be the main, determining factor in the system but must be integrated into the complete design process. A Low-Floor Bus design is used to illustrate this point. The influence of advances in drive-train electronics is illustrated as are novel designs for motors and mechanical transmission of power to the wheels allowing the use of novel hub assemblies. A hybrid electric power system is being deployed in which Fuel Cells produce the energy needs but are coupled with batteries especially for acceleration phases and for recuperative braking.

Hybrid Electric Transit Bus

NASA Technical Reports Server (NTRS)

Viterna, Larry A.

1997-01-01

A government, industry, and university cooperative is developing an advanced hybrid electric city transit bus. Goals of this effort include doubling the fuel economy compared to current buses and reducing emissions to one-tenth of current EPA standards. Unique aspects of the vehicle's power system include the use of ultra-capacitors as an energy storage system, and a planned natural gas fueled turbogenerator developed from a small jet engine. Power from both the generator and energy storage system is provided to a variable speed electric motor attached to the rear axle. At over 15000 kg gross weight, this is the largest vehicle of its kind ever built using ultra-capacitor energy storage. This paper describes the overall power system architecture, the evolution of the control strategy, and its performance over industry standard drive cycles.

NASA's Involvement in Technology Development and Transfer: The Ohio Hybrid Bus Project

NASA Technical Reports Server (NTRS)

Viterna, Larry A.

1997-01-01

A government and industry cooperative is using advanced power technology in a city transit bus that will offer double the fuel economy, and reduce emissions to one tenth of government standards. The heart of the vehicle's power system is a natural gas fueled generator unit. Power from both the generator and an advanced energy storage system is provided to a variable speed electric motor attached to the rear drive axle. A unique aspect of the vehicle's design is its use of "super" capacitors for recovery of energy during braking. This is the largest vehicle ever built using this advanced energy recovery technology. This paper describes the project goals and approach, results of its system performance modeling, and the status of the development team's effort.

Labeled line drawing of Magellan spacecraft

NASA Technical Reports Server (NTRS)

1988-01-01

Labeled line drawing identifies Magellan spacecraft components including forward equipment module, star scanner, propulsion module, rocket engine module, thermal control louvers, solar panel drive and cable wrap, solar panel, bus, altimeter antenna, low-gain antenna, and high gain antenna. Magellan, named for the 16th century Portuguese explorer, will be deployed from the payload bay (PLB) of Atlantis, Orbiter Vehicle (OV) 104, during mission STS-30.

Bidirectional DC-DC conversion device use at system of urban electric transport

NASA Astrophysics Data System (ADS)

Vilberger, M. E.; Vislogusov, D. P.; Kotin, D. A.; Kulekina, A. V.

2017-10-01

The paper considers questions of energy storage devices used in electric transport, especially in the electric traction drive of a trolley bus, in order to provide an autonomous motion, overhead system’s load leveling and energy recovering. For efficiency of the proposed system, a bidirectional DC-DC converter is used. During the simulation, regulation characteristics of the bidirectional DC-DC converters were obtained.

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Performance Verification Report: AMSU-A1 Antenna Drive Subsystem, PN 1331720-2, S/N 106

NASA Technical Reports Server (NTRS)

Luu, D.

1999-01-01

This is the Performance Verification Report, AMSU-A1 Antenna Drive Subsystem, P/N 1331720-2, S/N 106, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A). The antenna drive subsystem of the METSAT AMSU-A1, S/N 106, P/N 1331720-2, completed acceptance testing per A-ES Test Procedure AE-26002/lD. The test included: Scan Motion and Jitter, Pulse Load Bus Peak Current and Rise Time, Resolver Reading and Position Error, Gain/ Phase Margin, and Operational Gain Margin. The drive motors and electronic circuitry were also tested at the component level. The drive motor test includes: Starting Torque Test, Motor Commutation Test, Resolver Operation/ No-Load Speed Test, and Random Vibration. The electronic circuitry was tested at the Circuit Card Assembly (CCA) level of production; each test exercised all circuit functions. The transistor assembly was tested during the W3 cable assembly (1356941-1) test.

Reducing transit bus emissions: Alternative fuels or traffic operations?

NASA Astrophysics Data System (ADS)

Alam, Ahsan; Hatzopoulou, Marianne

2014-06-01

In this study, we simulated the operations and greenhouse gas (GHG) emissions of transit buses along a busy corridor and quantified the effects of two different fuels (conventional diesel and compressed natural gas) as well as a set of driving conditions on emissions. Results indicate that compressed natural gas (CNG) reduces GHG emissions by 8-12% compared to conventional diesel, this reduction could increase to 16% with high levels of traffic congestion. However, the benefits of switching from conventional diesel to CNG are less apparent when the road network is uncongested. We also investigated the effects of bus operations on emissions by applying several strategies such as transit signal priority (TSP), queue jumper lanes, and relocation of bus stops. Results show that in congested conditions, TSP alone can reduce GHG emissions by 14% and when combined with improved technology; a reduction of 23% is achieved. The reduction benefits are even more apparent when other transit operational improvements are combined with TSP. Finally a sensitivity analysis was performed to investigate the effect of operational improvements on emissions under varying levels of network congestion. We observe that under “extreme congestion”, the benefits of TSP decrease.

Sleep patterns and sleep-related complaints of Brazilian interstate bus drivers.

PubMed

Mello, M T; Santana, M G; Souza, L M; Oliveira, P C; Ventura, M L; Stampi, C; Tufik, S

2000-01-01

Sleep-related complaints have become a highlight for physicians as well as public health administrators. Studies of sleep patterns and sleep-related complaints of shift workers have been useful in minimizing reduction in the quality of life due to the warping of the sleep-wake cycle. The objective of the present study was to assess patterns of sleep, sleep-related complaints as well as physical activity and scoring rates for depression and anxiety in interstate bus drivers. Data were obtained with a sleep questionnaire, with the Beck inventory for depression, and the State-Trait Anxiety Inventory (STAI). A total of 400 interstate bus drivers from the northern, southern, central-western and south-eastern regions of Brazil were interviewed. Sixty percent of the subjects interviewed presented at least one sleep-related complaint, 16% admitted to have dozed at the wheel while on duty, and 41% stated that they exercised on a regular basis. Other sleep disturbance complaints reported were: sleep latency 29'17"; physical fatigue, 59.8%; mental fatigue, 45.4%; sleepiness, 25.8%; irritability, 20.6%; insomnia, 37.5%, respiratory disturbances, 19. 25% and snoring, 20.75%. Scores for anxiety and depression were not in the pathological range. The present data reinforce the view that bus drivers are generally discontent with shift work and its effects on sleep. Consequently, it is very important to establish an appropriate work schedule for drivers, besides implementing photo-therapy and physical activities in order to minimize sleepiness when driving.

Association of Graduated Driver Licensing With Driver, Non-Driver, and Total Fatalities Among Adolescents.

PubMed

Zhu, Motao; Zhao, Songzhu; Long, D Leann; Curry, Allison E

2016-07-01

Graduated driver licensing systems typically require an extended learner permit phase, and create night-time driving or passenger restrictions for adolescent drivers. Restricted driving might increase the use of alternative transportation to replace driving and consequently increase crashes and injuries for passengers, bus riders, pedestrians, and bicyclists. This study examined whether graduated driver licensing increases non-driver fatalities among adolescents, and whether it reduces total traffic fatalities combining drivers and non-drivers. Longitudinal analyses were conducted using data from the 1995-2012 U.S. Fatality Analysis Reporting System. Adjusted rate ratios were estimated for being fatally injured in a crash according to: (1) presence/absence of a graduated driver licensing system; and (2) four levels of graduated driver licensing systems (absent, weak, medium, strong). Analyses were conducted in 2015. Among adolescents aged 16 years, graduated driver licensing was not associated with increased passenger fatalities (adjusted rate ratio, 0.96; 95% CI=0.90, 1.03) or pedestrian and bicyclist fatalities (adjusted rate ratio, 1.09; 95% CI=0.85, 1.39), but was associated with an 11% reduction in total traffic fatalities. Among those aged 17 years, graduated driver licensing was not associated with increased fatalities as passengers, pedestrians, or bicyclists, and was not associated with reduced total traffic fatalities. In general, graduated driver licensing systems were not associated with increased fatalities as passengers, pedestrians, bicyclists, and bus riders. Graduated driver licensing systems were associated with reduced total fatalities of adolescents aged 16 years. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Can in Space-Status and Future after ECSS-E-ST-50-15C Release

NASA Astrophysics Data System (ADS)

Taylor, Chris; Furano, Gianluca; Valverde-Carretero, Alberto; Marinis, Kostas; Magistrati, Giorgio; Bolognino, Luca; Richard Jansen, King Lam; Caramia, Maurizio; Grau Llovera, Angel; Dalenq, Jean; Vinet, Francois

2015-09-01

Nowadays Controller Area Network (CAN) Bus is used more and more in spacecraft onboard applications. It has already been successfully used in many missions (ATV, SMART-1, MATROSHKA, SSTL Satellites, SENTINEL-2 etc.), will soon be the the main onboard communications bus for the EXOMars Mission and in will enable extended capabilities on future European Telecom palatforms. CAN Bus provides numerous advantages (robust, low cost, low power consumption, European, etc.). Thanks to its wide acceptance in the commercial market, numerous development tools are available that support and reduce the cost of all the engineering process, from specifications and design to the final assembly, integration and tests. Since 2009, ESA-ESTEC established an ESA-Industry Working Group on CAN Bus, in order to identify the main issues for its use in space applications and drive research and development. This long process has finally provided as output an ECSS standard and a set of building blocks that fully enable deployment of CAN bus for platform and payload use in all classes of space missions. The EXOMars project team has spearheaded these efforts, taking as reference the draft guidelines, and has taken into account the particularities of the EXOMars mission requirements, in order to provide a consistent methodology for the development of the multiple units that need to interface with the CAN Bus. The selection of CANOpen as preferred higher layer protocol for CAN in space application is due to the experience and hindsight developed during this long and sometimes not linear process. Two notable efforts were the development of an hardware support layer (the CCIPC IP core) for the CANOpen protocol and the qualification of three rad hard transceivers compliant with CAN commercial ISO physical standard. The CCIPC development has been performed concurrently with the ECSS-E-50-15C standardization activities. This approach has allowed the constant monitoring of the adopted IP core design solution by the ECSS Working Group. The first flight of the CCIPC is foreseen in 2016 with the EXOMARS Entry Descent and Landing Demonstrator Module. This paper will focus on the implementation of CAN Bus for all the future sapce DHSs, both on the technical aspects of physical layer selection, particularities of the higher layer protocol, etc. and on the methodology aspects related to the procurement of multiple heterogeneous units that are required to provide a standard interface to the Bus. Finally, a critical review of the current CAN Bus draft ECSS standard will be presented, based on advantages and difficulties encountered in the application of the current draft standard in the ongoing space applications.

Design and realization of high voltage disconnector condition monitoring system

NASA Astrophysics Data System (ADS)

Shi, Jinrui; Xu, Tianyang; Yang, Shuixian; Li, Buoyang

2017-08-01

The operation status of the high voltage disconnector directly affects the safe and stable operation of the power system. This article uses the wireless frequency hopping communication technology of the communication module to achieve the temperature acquisition of the switch contacts and high voltage bus, to introduce the current value of the loop in ECS, and judge the operation status of the disconnector by considering the ambient temperature, calculating the temperature rise; And through the acquisition of the current of drive motor in the process of switch closing and opening, and fault diagnosis of the disconnector by analyzing the change rule of the drive motor current, the condition monitoring of the high voltage disconnector is realized.

Understanding the knowledge and attitudes of commercial drivers in Ghana regarding alcohol impaired driving

PubMed Central

Asiamah, G; Mock, C; Blantari, J

2002-01-01

Objectives: The knowledge and attitudes of commercial drivers in Ghana as regards alcohol impaired driving were investigated. This was done in order to provide information that could subsequently be used to develop antidrunk driving social marketing messages built upon the intrinsic values and motivation of these drivers. Methods: Focus group discussions were held with 43 bus and minibus drivers in the capital city, Accra. A structured discussion guide was used to capture information related to values, risk perceptions, leisure time activities, and attitudes on alcohol impaired driving. Results: The majority of drivers expressed an understanding that drunk driving was a significant risk factor for crashes. There was a significant under-appreciation of the extent of the problem, however. Most believed that it was only rare, extremely intoxicated drivers who were the problem. The drivers also had a minimal understanding of the concept of blood alcohol concentration and related legal limits. Despite these factors, there was widespread support for increased enforcement of existing antidrunk driving laws. Conclusions: In Ghana, commercial drivers understand the basic danger of drunk driving and are motivated to assist in antidrunk driving measures. There are misconceptions and deficits in knowledge that need to be addressed in subsequent educational campaigns. PMID:11928975

Bringing MapReduce Closer To Data With Active Drives

NASA Astrophysics Data System (ADS)

Golpayegani, N.; Prathapan, S.; Warmka, R.; Wyatt, B.; Halem, M.; Trantham, J. D.; Markey, C. A.

2017-12-01

Moving computation closer to the data location has been a much theorized improvement to computation for decades. The increase in processor performance, the decrease in processor size and power requirement combined with the increase in data intensive computing has created a push to move computation as close to data as possible. We will show the next logical step in this evolution in computing: moving computation directly to storage. Hypothetical systems, known as Active Drives, have been proposed as early as 1998. These Active Drives would have a general-purpose CPU on each disk allowing for computations to be performed on them without the need to transfer the data to the computer over the system bus or via a network. We will utilize Seagate's Active Drives to perform general purpose parallel computing using the MapReduce programming model directly on each drive. We will detail how the MapReduce programming model can be adapted to the Active Drive compute model to perform general purpose computing with comparable results to traditional MapReduce computations performed via Hadoop. We will show how an Active Drive based approach significantly reduces the amount of data leaving the drive when performing several common algorithms: subsetting and gridding. We will show that an Active Drive based design significantly improves data transfer speeds into and out of drives compared to Hadoop's HDFS while at the same time keeping comparable compute speeds as Hadoop.

Fuzzy control based engine sizing optimization for a fuel cell/battery hybrid mini-bus

NASA Astrophysics Data System (ADS)

Kim, Minjin; Sohn, Young-Jun; Lee, Won-Yong; Kim, Chang-Soo

The fuel cell/battery hybrid vehicle has been focused for the alternative engine of the existing internal-combustion engine due to the following advantages of the fuel cell and the battery. Firstly, the fuel cell is highly efficient and eco-friendly. Secondly, the battery has the fast response for the changeable power demand. However, the competitive efficiency of the hybrid fuel cell vehicle is necessary to successfully alternate the conventional vehicles with the fuel cell hybrid vehicle. The most relevant factor which affects the overall efficiency of the hybrid fuel cell vehicle is the relative engine sizing between the fuel cell and the battery. Therefore the design method to optimize the engine sizing of the fuel cell hybrid vehicle has been proposed. The target system is the fuel cell/battery hybrid mini-bus and its power distribution is controlled based on the fuzzy logic. The optimal engine sizes are determined based on the simulator developed in this paper. The simulator includes the several models for the fuel cell, the battery, and the major balance of plants. After the engine sizing, the system efficiency and the stability of the power distribution are verified based on the well-known driving schedule. Consequently, the optimally designed mini-bus shows good performance.

An open-source laser electronics suite

NASA Astrophysics Data System (ADS)

Pisenti, Neal C.; Reschovsky, Benjamin J.; Barker, Daniel S.; Restelli, Alessandro; Campbell, Gretchen K.

2016-05-01

We present an integrated set of open-source electronics for controlling external-cavity diode lasers and other instruments in the laboratory. The complete package includes a low-noise circuit for driving high-voltage piezoelectric actuators, an ultra-stable current controller based on the design of, and a high-performance, multi-channel temperature controller capable of driving thermo-electric coolers or resistive heaters. Each circuit (with the exception of the temperature controller) is designed to fit in a Eurocard rack equipped with a low-noise linear power supply capable of driving up to 5 A at +/- 15 V. A custom backplane allows signals to be shared between modules, and a digital communication bus makes the entire rack addressable by external control software over TCP/IP. The modular architecture makes it easy for additional circuits to be designed and integrated with existing electronics, providing a low-cost, customizable alternative to commercial systems without sacrificing performance.

The realization of an SVGA OLED-on-silicon microdisplay driving circuit

NASA Astrophysics Data System (ADS)

Bohua, Zhao; Ran, Huang; Fei, Ma; Guohua, Xie; Zhensong, Zhang; Huan, Du; Jiajun, Luo; Yi, Zhao

2012-03-01

An 800 × 600 pixel organic light-emitting diode-on-silicon (OLEDoS) driving circuit is proposed. The pixel cell circuit utilizes a subthreshold-voltage-scaling structure which can modulate the pixel current between 170 pA and 11.4 nA. In order to keep the voltage of the column bus at a relatively high level, the sample-and-hold circuits adopt a ping-pong operation. The driving circuit is fabricated in a commercially available 0.35 μm two-poly four-metal 3.3 V mixed-signal CMOS process. The pixel cell area is 15 × 15 μm2 and the total chip occupies 15.5 × 12.3 mm2. Experimental results show that the chip can work properly at a frame frequency of 60 Hz and has a 64 grayscale (monochrome) display. The total power consumption of the chip is about 85 mW with a 3.3V supply voltage.

Novel concept for driving the linear compressor of a micro-miniature split Stirling cryogenic cooler

NASA Astrophysics Data System (ADS)

Maron, V.; Veprik, A.; Finkelstein, L.; Vilenchik, H.; Ziv, I.; Pundak, N.

2009-05-01

New methods of carrying out homeland security and antiterrorist operations call for the development of a new generation of mechanically cooled, portable, battery powered infrared imagers, relying on micro-miniature Stirling cryogenic coolers of rotary or linear types. Since split Stirling linearly driven micro-miniature cryogenic coolers have inherently longer life spans, low vibration export and better aural stealth as compared to their rotary driven rivals, they are more suitable for the above applications. The performance of such cryogenic coolers depends strongly on the efficacy of their electronic drivers. In a traditional approach, the PWM power electronics produce the fixed frequency tonal driving voltage/current, the magnitude of which is modulated via a PID control law so as to maintain the desired focal plane array temperature. The disadvantage of such drivers is that they draw high ripple current from the system's power bus. This results in the need for an oversized DC power supply (battery packs) and power electronic components, low efficiency due to excessive conductive losses and high residual electromagnetic interference which in turn degrades the performance of other systems connected to the same power bus. Without either an active line filter or large and heavy passive filtering, other electronics can not be powered from the same power bus, unless they incorporate heavy filtering at their inputs. The authors present the results of a feasibility study towards developing a novel "pumping" driver consuming essentially constant instant battery power/current without making use of an active or passive filter. In the tested setup, the driver relies on a bidirectional controllable bridge, invertible with the driving frequency, and a fast regulated DC/DC converter which maintains a constant level of current consumed from the DC power supply and thus operates in input current control mode. From the experimental results, the steady-state power consumed by the linear compressor remains the same as compared with the traditional sine wave driver, the voltage and current drawn from the battery pack is essentially free of low frequency ripple (this without use of any kind of filtering) and the overall coefficient of performance of the driver is in excess of 94% over the entire working range of supply voltages. Such a driver free of sine forming PWM stage and have reduced power peaks in all power conversion components.

An assessment of commercial motor vehicle driver distraction using naturalistic driving data.

PubMed

Hickman, Jeffrey S; Hanowski, Richard J

2012-01-01

This study analyzed naturalistic driving data from commercial trucks (3-axle and tractor-trailer/tanker) and buses (transit and motorcoach) during a 3-month period. The data set contained 183 commercial truck and bus fleets comprising 13,306 vehicles and included 1085 crashes, 8375 near crashes, 30,661 crash-relevant conflicts, and 211,171 baseline events. Study results documented the prevalence of tertiary tasks and the risks associated with performing these tasks while driving. Results indicated the odds of involvement in a safety-critical event differed as a function of performing different cell phone-related subtasks while driving. Although the odds ratio for talking/listening on a cell phone while driving was found to not significantly increase the likelihood of involvement in a safety-critical event, other cell phone subtasks (e.g., texting, dialing, reaching) were found to significantly increase the odds of involvement in a safety-critical event. The results suggest that cell phone use while driving should not be considered a simple dichotomous task (yes/no). Consideration should instead be made for a set of discrete cell phone subtasks that are each associated with varying levels of risk. Several hypotheses are presented to explain why cell phone use while driving was found to not increase the likelihood of involvement in a safety-critical event.

Comparison of on-road emissions for hybrid and regular transit buses.

PubMed

Hallmark, Shauna L; Wang, Bo; Sperry, Robert

2013-10-01

Hybrid technology offers an attractive option for transit buses, since it has the potential to significantly reduce operating costs for transit agencies. The main impetus behind use of hybrid transit vehicles is fuel savings and reduced emissions. Laboratory tests have indicated that hybrid transit buses can have significantly lower emissions compared with conventional transit buses. However the number of studies is limited and laboratory tests may not represent actual driving conditions, since in-use vehicle operation differs from laboratory test cycles. This paper describes an on-road evaluation of in-use emission differences between hybrid-electric and conventional transit buses for the Ames, Iowa transit authority, CyRide. Emissions were collected on-road using a portable emissions monitoring system (PEMS) for three hybrid and two control buses. Emissions were collected for at least one operating bus day. Each bus was evaluated over the same route pattern, which utilizes the same driver. The number of passengers embarking or disembarking at each stop was collected by an on-board data collector so that passenger load could be included. Vehicle emissions are correlated to engine load demand, which is a function of factors such as vehicle load, speed, and acceleration. PEMS data are provided second by second and vehicle-specific power (VSP) was calculated for each row of data. Instantaneous data were stratified into the defined VSP bins and then average modal emission rates and standard errors were calculated for each bus for each pollutant. Pollutants were then compared by bus type. Carbon dioxide, carbon monoxide, and hydrocarbon emissions were higher for the regular buses across most VSP bins than for the hybrid buses. Nitrogen oxide emissions were unexpectedly higher for the hybrid buses than for the control buses.

Electromagnetic Gun With Commutated Coils

NASA Technical Reports Server (NTRS)

Elliott, David G.

1991-01-01

Proposed electromagnetic gun includes electromagnet coil, turns of which commutated in sequence along barrel. Electrical current fed to two armatures by brushes sliding on bus bars in barrel. Interaction between armature currents and magnetic field from coil produces force accelerating armature, which in turn, pushes on projectile. Commutation scheme chosen so magnetic field approximately coincides and moves with cylindrical region defined by armatures. Scheme has disadvantage of complexity, but in return, enables designer to increase driving magnetic field without increasing armature current. Attainable muzzle velocity increased substantially.

60. VIEW OF THE CURRENT TRANSFORMER VAULT. THIS CURRENT TRANSFORMER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. VIEW OF THE CURRENT TRANSFORMER VAULT. THIS CURRENT TRANSFORMER WAS USED TO SENSE HIGH CURRENT BEING GENERATED ON GENERATOR NUMBER 3 AND REDUCE IT TO A LOWER, EXACT ANALOG VALUE THAT COULD BE SAFELY HANDLED AND MONITORED WITH THE CONTROL CIRCUITRY. THE CURRENT TRANSFORMER IS LOCATED IN THE CENTER OF THE PHOTOGRAPH. THE CONNECTING BUS ABOVE THE TRANSFORMER WAS REMOVED FOR SALVAGE. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Design and Integration of a Three Degrees-of-Freedom Robotic Vehicle with Control Moment Gyro for the Autonomous Multi-Agent Physically Interacting Spacecraft (AMPHIS) Testbed

DTIC Science & Technology

2006-09-01

required directional control for each thruster due to their high precision and equivalent power and computer interface requirements to those for the...Universal Serial Bus) ports, LPT (Line Printing Terminal) and KVM (Keyboard-Video- Mouse) interfaces. Additionally, power is supplied to the computer through...of the IDE cable to the Prometheus Development Kit ACC-IDEEXT. Connect a small drive power connector from the desktop ATX power supply to the ACC

Single bus star connected reluctance drive and method

DOEpatents

Fahimi, Babak; Shamsi, Pourya

2016-05-10

A system and methods for operating a switched reluctance machine includes a controller, an inverter connected to the controller and to the switched reluctance machine, a hysteresis control connected to the controller and to the inverter, a set of sensors connected to the switched reluctance machine and to the controller, the switched reluctance machine further including a set of phases the controller further comprising a processor and a memory connected to the processor, wherein the processor programmed to execute a control process and a generation process.

Saturday Driving Restrictions Fail to Improve Air Quality in Mexico City.

PubMed

Davis, Lucas W

2017-02-02

Policymakers around the world are turning to license-plate based driving restrictions in an effort to address urban air pollution. The format differs across cities, but most programs restrict driving once or twice a week during weekdays. This paper focuses on Mexico City, home to one of the oldest and best-known driving restriction policies. For almost two decades Mexico City's driving restrictions applied during weekdays only. This changed recently, however, when the program was expanded to include Saturdays. This paper uses hourly data from pollution monitoring stations to measure the effect of the Saturday expansion on air quality. Overall, there is little evidence that the program expansion improved air quality. Across eight major pollutants, the program expansion had virtually no discernible effect on pollution levels. These disappointing results stand in sharp contrast to estimates made before the expansion which predicted a 15%+ decrease in vehicle emissions on Saturdays. To understand why the program has been less effective than expected, the paper then turns to evidence from subway, bus, and light rail ridership, finding no evidence that the expansion was successful in getting drivers to switch to lower-emitting forms of transportation.

Saturday Driving Restrictions Fail to Improve Air Quality in Mexico City

NASA Astrophysics Data System (ADS)

Davis, Lucas W.

2017-02-01

Policymakers around the world are turning to license-plate based driving restrictions in an effort to address urban air pollution. The format differs across cities, but most programs restrict driving once or twice a week during weekdays. This paper focuses on Mexico City, home to one of the oldest and best-known driving restriction policies. For almost two decades Mexico City’s driving restrictions applied during weekdays only. This changed recently, however, when the program was expanded to include Saturdays. This paper uses hourly data from pollution monitoring stations to measure the effect of the Saturday expansion on air quality. Overall, there is little evidence that the program expansion improved air quality. Across eight major pollutants, the program expansion had virtually no discernible effect on pollution levels. These disappointing results stand in sharp contrast to estimates made before the expansion which predicted a 15%+ decrease in vehicle emissions on Saturdays. To understand why the program has been less effective than expected, the paper then turns to evidence from subway, bus, and light rail ridership, finding no evidence that the expansion was successful in getting drivers to switch to lower-emitting forms of transportation.

Saturday Driving Restrictions Fail to Improve Air Quality in Mexico City

PubMed Central

Davis, Lucas W.

2017-01-01

Policymakers around the world are turning to license-plate based driving restrictions in an effort to address urban air pollution. The format differs across cities, but most programs restrict driving once or twice a week during weekdays. This paper focuses on Mexico City, home to one of the oldest and best-known driving restriction policies. For almost two decades Mexico City’s driving restrictions applied during weekdays only. This changed recently, however, when the program was expanded to include Saturdays. This paper uses hourly data from pollution monitoring stations to measure the effect of the Saturday expansion on air quality. Overall, there is little evidence that the program expansion improved air quality. Across eight major pollutants, the program expansion had virtually no discernible effect on pollution levels. These disappointing results stand in sharp contrast to estimates made before the expansion which predicted a 15%+ decrease in vehicle emissions on Saturdays. To understand why the program has been less effective than expected, the paper then turns to evidence from subway, bus, and light rail ridership, finding no evidence that the expansion was successful in getting drivers to switch to lower-emitting forms of transportation. PMID:28151487

Robust interface between flying and topological qubits

PubMed Central

Xue, Zheng-Yuan; Gong, Ming; Liu, Jia; Hu, Yong; Zhu, Shi-Liang; Wang, Z. D.

2015-01-01

Hybrid architectures, consisting of conventional and topological qubits, have recently attracted much attention due to their capability in consolidating robustness of topological qubits and universality of conventional qubits. However, these two kinds of qubits are normally constructed in significantly different energy scales, and thus the energy mismatch is a major obstacle for their coupling, which can support the exchange of quantum information between them. Here we propose a microwave photonic quantum bus for a strong direct coupling between the topological and conventional qubits, where the energy mismatch is compensated by an external driving field. In the framework of tight-binding simulation and perturbation approach, we show that the energy splitting of Majorana fermions in a finite length nanowire, which we use to define topological qubits, is still robust against local perturbations due to the topology of the system. Therefore, the present scheme realizes a rather robust interface between the flying and topological qubits. Finally, we demonstrate that this quantum bus can also be used to generate multipartitie entangled states with the topological qubits. PMID:26216201

Development of a software interface for optical disk archival storage for a new life sciences flight experiments computer

NASA Technical Reports Server (NTRS)

Bartram, Peter N.

1989-01-01

The current Life Sciences Laboratory Equipment (LSLE) microcomputer for life sciences experiment data acquisition is now obsolete. Among the weaknesses of the current microcomputer are small memory size, relatively slow analog data sampling rates, and the lack of a bulk data storage device. While life science investigators normally prefer data to be transmitted to Earth as it is taken, this is not always possible. No down-link exists for experiments performed in the Shuttle middeck region. One important aspect of a replacement microcomputer is provision for in-flight storage of experimental data. The Write Once, Read Many (WORM) optical disk was studied because of its high storage density, data integrity, and the availability of a space-qualified unit. In keeping with the goals for a replacement microcomputer based upon commercially available components and standard interfaces, the system studied includes a Small Computer System Interface (SCSI) for interfacing the WORM drive. The system itself is designed around the STD bus, using readily available boards. Configurations examined were: (1) master processor board and slave processor board with the SCSI interface; (2) master processor with SCSI interface; (3) master processor with SCSI and Direct Memory Access (DMA); (4) master processor controlling a separate STD bus SCSI board; and (5) master processor controlling a separate STD bus SCSI board with DMA.

Galileo IOV Electrical Power Subsystem Relies On Li-Ion Batter Charge Management Controlled By Hardware

NASA Astrophysics Data System (ADS)

Douay, N.

2011-10-01

In the frame of GALILEO In-Orbit Validation program which is composed of 4 satellites, Thales Alenia Space France has designed, developed and tested the Electrical Power Subsystem. Besides some classical design choices like: -50V regulated main power bus provided by the PCDU manufactured by Terma (DK), -Solar array, manufactured by Dutch-Space (NL), using Ga-As triple junction technology from Azur Space Power Solar GmbH, -SAFT (FR) Lithium-ion Battery for which cell package balancing function is required, -Solar Array Drive Mechanism, provided by RUAG Space Switzerland, to transfer the power. This subsystem features a fully autonomous, failure tolerant, battery charge management able to operate even after a complete unavailability of the on-board software. The battery charge management is implemented such that priority is always given to satisfy the satellite main bus needs in order to maintain the main bus regulation under MEA control. This battery charge management principle provides very high reliability and operational robustness. So, the paper describes : -the battery charge management concept using a combination of PCDU hardware and relevant battery lines monitoring, -the functional aspect of the single point failure free S4R (Sequential Switching Shunt Switch Regulator) and associated performances, -the failure modes isolated and passivated by this architecture. The paper will address as well the autonomous balancing function characteristics and performances.

[Driving ability and fitness to drive in people with diabetes mellitus].

PubMed

Seeger, Rolf; Lehmann, Roger

2011-05-01

Chronic sequelae of diabetes that could potentially affect driving include the following: visual retinopathy with associated impaired visual acuity, loss of peripheral vision and poor dark adaptation; neuropathy that may affect lower limb functions needed for safe driving; and acute events, including transient cognitive dysfunction and loss of consciousness related to hypo- or hyperglycemia. Hyperglycemia does not suddenly incapacitate drivers, however its occurrence often leads to tiredness, blurred vision, decreased visual acuity and adjustment of treatment which may precipitate hypoglycaemia. The side effects of acute hypoglycemia are of particular concern, as they include slowing of both cognitive and motor functions. Hypoglycemia while driving ist the most important complication in persons treated with insulin, sulfonylureas or glinides. They can be prevented, however, by frequent measuring blood glucose before and every 60 to 90 minutes during driving, by keeping sugary snacks (carbohydrates) in the vehicle, and by taking carbohydrates in case of glucose levels below 5 mmol/l. For patients, who are treated with insulin and sulfonylureas/glinides, it is of utmost importance fort the treating physician to frequently talk about successful strategies for preventing hypoglycemias, and thus accidents, while driving. People with diabetes treated with insulin, sulfonylureas or glinides are nor allowed to drive a bus, taxi, or truck (commercial driving). Under special circumstances (evalution and treatment by a diabetologist/endocrinolgist, avoidance of hypoglycemias for three months, and frequent glucose measurements) an exception to this rule can be granted for truck and cab drivers (after a thorough licensing examination).

Next Generation Environmentally-Friendly Driving Feedback Systems Research and Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barth, Matthew; Boriboonsomsin, Kanok

2014-12-31

The objective of this project is to design, develop, and demonstrate a next-generation, federal safety- and emission-complaint driving feedback system that can be deployed across the existing vehicle fleet and improve fleet average fuel efficiency by at least 2%. The project objective was achieved with the driving feedback system that encourages fuel-efficient vehicle travel and operation through: 1) Eco-Routing Navigation module that suggests the most fuel-efficient route from one stop to the next, 2) Eco-Driving Feedback module that provides sensible information, recommendation, and warning regarding fuel-efficient vehicle operation, and 3) Eco-Score and Eco-Rank module that provides a means for drivingmore » performance tracking, self-evaluation, and peer comparison. The system also collects and stores vehicle travel and operation data, which are used by Algorithm Updating module to customize the other modules for specific vehicles and adapts them to specific drivers over time. The driving feedback system was designed and developed as an aftermarket technology that can be retrofitted to vehicles in the existing fleet. It consists of a mobile application for smart devices running Android operating system, a vehicle on-board diagnostics connector, and a data server. While the system receives and utilizes real-time vehicle and engine data from the vehicle’s controller area network bus through the vehicle’s on-board diagnostic connector, it does not modify or interfere with the vehicle’s controller area network bus, and thus, is in compliance with federal safety and emission regulations. The driving feedback system was demonstrated and then installed on 45 vehicles from three different fleets for field operational test. These include 15 private vehicles of the general public, 15 pickup trucks of the California Department of Transportation that are assigned to individual employees for business use, and 15 shuttle buses of the Riverside Transit Agency that are used for paratransit service. Detailed vehicle travel and operation data including route taken, driving speed, acceleration, braking, and the corresponding fuel consumption, were collected both before and during the test period. The data analysis results show that the fleet average fuel efficiency improvements for the three fleets with the use of the driving feedback system are in the range of 2% to 9%. The economic viability of the driving feedback system is high. A fully deployed system would require capital investment in smart device ($150-$350) and on-board diagnostics connector ($50-$100) as well as paying operating costs for wireless data plan and subscription fees ($20-$30 per month) for connecting to the data server and receiving various system services. For individual consumers who already own a smart device (such as smartphone) and commercial fleets that already use some kind of telematics services, the costs for deploying this driving feedback system would be much lower.« less

Simulations of the Fuel Economy and Emissions of Hybrid Transit Buses over Planned Local Routes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Zhiming; LaClair, Tim J; Daw, C Stuart

2014-01-01

We present simulated fuel economy and emissions city transit buses powered by conventional diesel engines and diesel-hybrid electric powertrains of varying size. Six representative city drive cycles were included in the study. In addition, we included previously published aftertreatment device models for control of CO, HC, NOx, and particulate matter (PM) emissions. Our results reveal that bus hybridization can significantly enhance fuel economy by reducing engine idling time, reducing demands for accessory loads, exploiting regenerative braking, and shifting engine operation to speeds and loads with higher fuel efficiency. Increased hybridization also tends to monotonically reduce engine-out emissions, but trends inmore » the tailpipe (post-aftertreatment) emissions involve more complex interactions that significantly depend on motor size and drive cycle details.« less

Vehicle drive module having improved terminal design

DOEpatents

Beihoff, Bruce C.; Radosevich, Lawrence D.; Phillips, Mark G.; Kehl, Dennis L.; Kaishian, Steven C.; Kannenberg, Daniel G.

2006-04-25

A terminal structure for vehicle drive power electronics circuits reduces the need for a DC bus and thereby the incidence of parasitic inductance. The structure is secured to a support that may receive one or more power electronic circuits. The support may aid in removing heat from the circuits through fluid circulating through the support. The support may form a shield from both external EMI/RFI and from interference generated by operation of the power electronic circuits. Features may be provided to permit and enhance connection of the circuitry to external circuitry, such as by direct contact between the terminal assembly and AC and DC circuit components. Modular units may be assembled that may be coupled to electronic circuitry via plug-in arrangements or through interface with a backplane or similar mounting and interconnecting structures.

Evaluation of the use of bioethanol fuelled buses based on ambient air pollution screening and on-road measurements.

PubMed

López-Aparicio, S; Hak, C

2013-05-01

Mitigation measures to reduce greenhouse gas emissions may have adverse effects on urban air quality and human exposure to harmful pollutants. The use of bioethanol fuelled vehicles is increasing worldwide and may create new undesired pollution effects. Different measurement campaigns were performed in a pilot study to contribute to the understanding of the consequences associated with the use of bioethanol blended fuel (E95) on a series of pollutants. Ambient screening measurements of NO2, O3, acetic acid, formaldehyde and acetaldehyde were performed at different urban locations, exposed and not exposed to the circulation of bioethanol buses. In addition, volatile organic compounds were measured at the exhaust pipe of a bioethanol fuelled bus, both under idling conditions (carbonyls; DNPH cartridge) and under on-road driving conditions applying online monitoring (PTR-TOF). Higher ambient acetaldehyde values were measured at locations exposed to bioethanol fuelled buses than at locations not exposed, and very high acetaldehyde and acetic acid values were measured from the exhaust pipe during driving conditions (acetaldehyde>150 ppm; acetic acid ≈ 20-30 ppm) and modelled at close distance to the bioethanol bus. Human exposure to high concentration of acetaldehyde is expected, and it may involve a significantly increased chance in developing cancer. The high concentration of acetic acid will involve odour annoyance and significant material degradation or corrosion. Copyright © 2013 Elsevier B.V. All rights reserved.

Mars Comm/Nav MicroSat Network Using the Multi-Mission Bus Launched Piggyback by Ariane 5

NASA Technical Reports Server (NTRS)

Hastrup, R. C.; Cesarone, R. J.; Morabito, D. D.

1999-01-01

Recently, NASA's Jet Propulsion Laboratory completed a Mars Exploration Program Architecture Definition Study with strong international participation. The recommendations of this study include establishment of a low cost in-situ communications and navigation satellite network to provide enabling and enhancing support for the international exploration of Mars. This would be the first step toward establishing a "virtual presence throughout the solar system" as called for in NASA's Strategic Plan. Response to the proposed comm/nav satellite network has been very favorably received, as reflected by the inclusion of a line item in NASA's budget submittal to Congress, which provides funding for implementation of the network with first launch in the 2003 opportunity. Funding has already been provided for a phase A study being conducted this year. This paper presents the planned implementation of the comm/nav network, which will utilize microsats based on a multi-mission spacecraft bus being designed for launch by the Ariane 5 as a secondary payload. A companion paper at this conference, entitled "The Multi-Purpose Mars Micro-Mission System Design Utilizing Ariane 5 Piggyback Launch", describes the multimission bus design. This paper addresses the application of the multi-mission bus to the comm/nav microsat mission. Following an introduction, which provides the background that has led to the proposed comm/nav network, the paper discusses the projected user needs with emphasis on the various possible robotic missions (landers, rovers, ascent vehicles, balloons, aircraft, etc.) progressing toward eventual piloted missions. Next, the paper describes the concept for an evolving network of comm/nav microsats and the expected capability to satisfy the user needs. Results of communications and navigation performance analysis are summarized for attractive satellite constellation configurations. The important comm/nav microsat functional requirements on the multi-mission spacecraft bus are described with discussion of the mission-system tradeoffs for the driving requirements. The functional design of the in-situ communications / navigation package, which constitutes the payload of the microsat, is also described. The paper also includes discussion of technologies which are of specific importance to the implementation of the comm/nav microsat network.

Experimental modeling of the effect of hurricane wind forces on driving behavior and vehicle performance.

PubMed

Rodriguez, Jose M; Codjoe, Julius; Osman, Osama; Ishak, Sherif; Wolshon, Brian

2015-01-01

While traffic planning is important for developing a hurricane evacuation plan, vehicle performance on the roads during extreme weather conditions is critical to the success of the planning process. This novel study investigates the effect of gusty hurricane wind forces on the driving behavior and vehicle performance. The study explores how the parameters of a driving simulator could be modified to reproduce wind loadings experienced by three vehicle types (passenger car, ambulance, and bus) during gusty hurricane winds, through manipulation of appropriate software. Thirty participants were then tested on the modified driving simulator under five wind conditions (ranging from normal to hurricane category 4). The driving performance measures used were heading error and lateral displacement. The results showed that higher wind forces resulted in more varied and greater heading error and lateral displacement. The ambulance had the greatest heading errors and lateral displacements, which were attributed to its large lateral surface area and light weight. Two mathematical models were developed to estimate the heading error and lateral displacements for each of the vehicle types for a given change in lateral wind force. Through a questionnaire, participants felt the different characteristics while driving each vehicle type. The findings of this study demonstrate the valuable use of a driving simulator to model the behavior of different vehicle types and to develop mathematical models to estimate and quantify driving behavior and vehicle performance under hurricane wind conditions.

Investigating the predictive of risk-taking attitudes and behaviors among Iranian drivers

PubMed Central

Habibi, Ehsanollah; Haghi, Azam; Maracy, Mohammad Reza

2014-01-01

Background: World Health Organization findings shows that up to year 2020 the number of fatality due to driving accidents will increases up to 65%, which is 80% is in developing countries. Iran has one of the highest rates of road traffic accident mortality rate in the world. Materials and Methods: The cross-sectional study was carried out in the center and west of Iran upon 540 ordinary and taxi drivers who were driving regularly from bus terminals and the travel agencies to other cities. Data collection tool is a questionnaire that measuring driving risk taking by two items of risky driving behaviors and risk taking attitudes. Findings: The results of this study showed that the averages of risk driving behaviors scores were higher than the average of risk taking attitudes scores. The results of logistic regression test showed that the risky driving behaviors can be a predictor of driving accidents due to individuals’ risk taking (P = 0.014). Among all these variables, attitude toward rule violations and speeding, aggressive driving and violation of the road laws respectively are important predictive of drivers’ risk taking (P < 0.0010). Discussion and Conclusion: Although attitude toward risk taking has been located at a low level by different ways, a desired result was not obtained from the reduction of those high risky behaviors; in fact, high-rate of accidents and traffic incidence in Iran indicates this matter well. PMID:24741659

Ultrafine PM emissions from natural gas, oxidation-catalyst diesel, and particle-trap diesel heavy-duty transit buses.

PubMed

Holmén, Britt A; Ayala, Alberto

2002-12-01

This paper addresses how current technologies effective for reducing PM emissions of heavy-duty engines may affect the physical characteristics of the particles emitted. Three in-use transit bus configurations were compared in terms of submicron particle size distributions using simultaneous SMPS measurements under two dilution conditions, a minidiluter and the legislated constant volume sampler (CVS). The compressed natural gas (CNG)-fueled and diesel particulate filter (DPF)-equipped diesel configurations are two "green" alternatives to conventional diesel engines. The CNG bus in this study did not have an oxidation catalyst whereas the diesel configurations (with and without particulate filter) employed catalysts. The DPF was a continuously regenerating trap (CRT). Particle size distributions were collected between 6 and 237 nm using 2-minute SMPS scans during idle and 55 mph steady-state cruise operation. Average particle size distributions collected during idle operation of the diesel baseline bus operating on ultralow sulfur fuel showed evidence for nanoparticle growth under CVS dilution conditions relative to the minidiluter. The CRT effectively reduced both accumulation and nuclei mode concentrations by factors of 10-100 except under CVS dilution conditions where nuclei mode concentrations were measured during 55 mph steady-state cruise that exceeded baseline diesel concentrations. The CVS data suggest some variability in trap performance. The CNG bus had accumulation mode concentrations 10-100x lower than the diesel baseline but often displayed large nuclei modes, especially under CVS dilution conditions. Partly this may be explained by the lack of an oxidation catalyst on the CNG, but differences between the minidiluter and CVS size distributions suggest that dilution ratio, temperature-related wall interactions, and differences in tunnel background between the diluters contributed to creating nanoparticle concentrations that sometimes exceeded diesel baseline concentrations when driving under load. The results do not support use of CVS dilution methodology for ultrafine particle sampling, and, despite attention to collection of tunnel blanks in this study, results indicate that a protocol needs to be determined and prescribed for taking into account tunnel blank "emissions" to obtain meaningful comparisons between different technologies. Of critical importance is determining how temperature differences between tunnel blank and test cycle sampling compare in terms of background particle numbers. Total particle number concentrations for the minidiluter sampling point were not significantly different for the two alternative technologies when considering all the steady-cycle data collected. Concentrations ranged from 0.8 to 3 x 10(6) for the baseline bus operating on ultralow sulfur fuel, from 0.5 to 9 x 10(4) for the diesel bus equipped with the CRT filter, and from 1 to 8 x 10(4) particles/cc for the CNG bus.

Formed photovoltaic module busbars

DOEpatents

Rose, Douglas; Daroczi, Shan; Phu, Thomas

2015-11-10

A cell connection piece for a photovoltaic module is disclosed herein. The cell connection piece includes an interconnect bus, a plurality of bus tabs unitarily formed with the interconnect bus, and a terminal bus coupled with the interconnect bus. The plurality of bus tabs extend from the interconnect bus. The terminal bus includes a non-linear portion.

Uncertainty in particle number modal analysis during transient operation of compressed natural gas, diesel, and trap-equipped diesel transit buses.

PubMed

Holmén, Britt A; Qu, Yingge

2004-04-15

The relationships between transient vehicle operation and ultrafine particle emissions are not well-known, especially for low-emission alternative bus technologies such as compressed natural gas (CNG) and diesel buses equipped with particulate filters/traps (TRAP). In this study, real-time particle number concentrations measured on a nominal 5 s average basis using an electrical low pressure impactor (ELPI) for these two bus technologies are compared to that of a baseline catalyst-equipped diesel bus operated on ultralow sulfur fuel (BASE) using dynamometer testing. Particle emissions were consistently 2 orders of magnitude lower for the CNG and TRAP compared to BASE on all driving cycles. Time-resolved total particle numbers were examined in terms of sampling factors identified as affecting the ability of ELPI to quantify the particulate matter number emissions for low-emitting vehicles such as CNG and TRAP as a function of vehicle driving mode. Key factors were instrument sensitivity and dilution ratio, alignment of particle and vehicle operating data, sampling train background particles, and cycle-to-cycle variability due to vehicle, engine, after-treatment, or driver behavior. In-cycle variability on the central business district (CBD) cycle was highest for the TRAP configuration, but this could not be attributed to the ELPI sensitivity issues observed for TRAP-IDLE measurements. Elevated TRAP emissions coincided with low exhaust temperature, suggesting on-road real-world particulate filter performance can be evaluated by monitoring exhaust temperature. Nonunique particle emission maps indicate that measures other than vehicle speed and acceleration are necessary to model disaggregated real-time particle emissions. Further testing on a wide variety of test cycles is needed to evaluate the relative importance of the time history of vehicle operation and the hysteresis of the sampling train/dilution tunnel on ultrafine particle emissions. Future studies should monitor particle emissions with high-resolution real-time instruments and account for the operating regime of the vehicle using time-series analysis to develop predictive number emissions models.

Criminal and legal responsibilities in Tourette's syndrome.

PubMed

Gullucayir, Sibel; Asirdizer, Mahmut; Yavuz, M Sunay; Zeyfeoglu, Yildiray; Ulucay, Tarik

2009-01-01

Tourette's Syndrome (TS) is a neuropsychological disorder characterized by the presence of multiple involuntary motor tics accompanied by one or more vocal tics. Articles about TS and criminal responsibility and the restriction of civil rights are limited. A person with TS was evaluated to consider his criminal responsibility after swearing at a referee during a football game. He was also evaluated as to whether or not he was capable of professionally driving a service bus. Additionally, medico-legal situations regarding military service, obtaining a shotgun license and marriages of patients with TS were considered.

Direct drive options for electric propulsion systems

NASA Technical Reports Server (NTRS)

Hamley, John A.

1995-01-01

Power processing units (PPU's) in an electric propulsion system provide many challenging integration issues. The PPU must provide power to the electric thruster while maintaining compatibility with all of the spacecraft power and data systems. Inefficiencies in the power processor produce heat, which must be radiated to the environment in order to ensure reliable operation. Although PPU efficiencies are generally greater than 0.9, heat loads are often substantial. This heat must be rejected by thermal control systems which generally have specific masses of 15-30 kg/kW. PPU's also represent a large fraction of the electric propulsion system dry mass. Simplification or elimination of power processing in a propulsion system would reduce the electric propulsion system specific mass and improve the overall reliability and performance. A direct drive system would eliminate all or some of the power supplies required to operate a thruster by directly connecting the various thruster loads to the solar array. The development of concentrator solar arrays has enabled power bus voltages in excess of 300 V which is high enough for direct drive applications for Hall thrusters such as the Stationary Plasma Thruster (SPT). The option of solar array direct drive for SPT's is explored to provide a comparison between conventional and direct drive system mass.

A Driving Cycle Detection Approach Using Map Service API

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Lei; Gonder, Jeffrey D

Following advancements in smartphone and portable global positioning system (GPS) data collection, wearable GPS data have realized extensive use in transportation surveys and studies. The task of detecting driving cycles (driving or car-mode trajectory segments) from wearable GPS data has been the subject of much research. Specifically, distinguishing driving cycles from other motorized trips (such as taking a bus) is the main research problem in this paper. Many mode detection methods only focus on raw GPS speed data while some studies apply additional information, such as geographic information system (GIS) data, to obtain better detection performance. Procuring and maintaining dedicatedmore » road GIS data are costly and not trivial, whereas the technical maturity and broad use of map service application program interface (API) queries offers opportunities for mode detection tasks. The proposed driving cycle detection method takes advantage of map service APIs to obtain high-quality car-mode API route information and uses a trajectory segmentation algorithm to find the best-matched API route. The car-mode API route data combined with the actual route information, including the actual mode information, are used to train a logistic regression machine learning model, which estimates car modes and non-car modes with probability rates. The experimental results show promise for the proposed method's ability to detect vehicle mode accurately.« less

Fast Charge Battery Electric Transit Bus In-Use Fleet Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prohaska, Robert; Kelly, Kenneth; Eudy, Leslie

2016-07-25

The focus of this interim fleet evaluation is to characterize and evaluate the operating behavior of Foothill Transit's fast charge battery electric buses (BEBs). Future research will compare the BEBs' performance to conventional vehicles. In an effort to better understand the impacts of drive cycle characteristics on advanced vehicle technologies, researchers at the National Renewable Energy Laboratory analyzed over 148,000 km of in-use operational data, including driving and charging events. This analysis provides an unbiased evaluation of advanced vehicle technologies in real-world operation demonstrating the importance of understanding the effects of road grade and heating, ventilating and air conditioning requirementsmore » when deploying electric vehicles. The results of this analysis show that the Proterra BE35 demonstrated an operating energy efficiency of 1.34 kWh/km over the data reporting period.« less

Fast Charge Battery Electric Transit Bus In-Use Fleet Evaluation: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prohaska, Robert; Eudy, Leslie; Kelly, Kenneth

2016-05-06

The focus of this interim fleet evaluation is to characterize and evaluate the operating behavior of Foothill Transit's fast charge battery electric buses (BEBs). Future research will compare the BEBs' performance to conventional vehicles. In an effort to better understand the impacts of drive cycle characteristics on advanced vehicle technologies, researchers at the National Renewable Energy Laboratory analyzed over 148,000 km of in-use operational data, including driving and charging events. This analysis provides an unbiased evaluation of advanced vehicle technologies in real-world operation demonstrating the importance of understanding the effects of road grade and heating, ventilating and air conditioning requirementsmore » when deploying electric vehicles. The results of this analysis show that the Proterra BE35 demonstrated an operating energy efficiency of 1.34 kWh/km over the data reporting period.« less

Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duran, A.; Walkowicz, K.

In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating across the country. Employing a combination of Isaac Instruments GPS/CAN data loggers in conjunction with existing onboard telemetric systems resulted in the capture of operating information for more than 200 individual vehicles in three geographically unique domestic locations. In total, over 1,500 individual operational route shifts from Washington, New York, and Colorado were collected. Upon completing the collection of in-use field data using either NREL-installed data acquisition devices ormore » existing onboard telemetry systems, large-scale duty-cycle statistical analyses were performed to examine underlying vehicle dynamics trends within the data and to explore vehicle operation variations between fleet locations. Based on the results of these analyses, high, low, and average vehicle dynamics requirements were determined, resulting in the selection of representative standard chassis dynamometer test cycles for each condition. In this paper, the methodology and accompanying results of the large-scale duty-cycle statistical analysis are presented, including graphical and tabular representations of a number of relationships between key duty-cycle metrics observed within the larger data set. In addition to presenting the results of this analysis, conclusions are drawn and presented regarding potential applications of advanced vehicle technology as it relates specifically to school buses.« less

COM-BUS : A Southern California Subscription Bus Service

DOT National Transportation Integrated Search

1977-05-01

The evolution and operations of the COM-BUS Subscription Commuter Bus Service are documented. COM-BUS is a privately owned organization operating at a profit without any form of subsidy. COM-BUS serves approximately 2,000 commuters per day on 47 rout...

49 CFR 605.19 - Approval of school bus operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Approval of school bus operations. 605.19 Section... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.19 Approval of school bus operations. (a) The Administrator will consider the comments filed by private school bus...

49 CFR 605.18 - Comments by private school bus operators.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Comments by private school bus operators. 605.18... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.18 Comments by private school bus operators. Private school bus operators may file written comments on an applicant's...

49 CFR 605.18 - Comments by private school bus operators.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Comments by private school bus operators. 605.18... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.18 Comments by private school bus operators. Private school bus operators may file written comments on an applicant's...

49 CFR 605.19 - Approval of school bus operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Approval of school bus operations. 605.19 Section... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.19 Approval of school bus operations. (a) The Administrator will consider the comments filed by private school bus...

A new bus lane on urban expressway with no-bay bus stop

NASA Astrophysics Data System (ADS)

Tian, Zhao; Jia, Limin

2016-01-01

The sharp increase in residents and vehicles causes heavy traffic pressure in many cities. To ease traffic congestion, it has been the common sense that we should develop public transit system. The priority of the bus appears particularly necessary with the rapid development of the public transport system. The bus lane is an important embodiment of the bus priority. Focusing on the problem of the unreasonable dedicated bus lane (DBL) under the lower ratio of buses, this paper proposed a new bus lane with limited physical length. And this bus lane can reduce the lane-changing conflict caused by the buses and cars running on roads without bus lanes. Based on the cellular automata (CA) traffic flow model and the lane-changing behavior of the vehicle including the optional lane-changing and the mandatory lane-changing, a three-lane traffic model with an isolated no-bay bus stop is proposed. The ordinary three-lane traffic without a bus lane and the cases of traffic with a DBL or the proposed bus lane are simulated, and the comparisons in the form of the fundamental diagrams are made among them. It is shown that the no-bay bus stop can act as a bottleneck on the traffic flow because of the mandatory lane-changing behavior. Under a certain ratio of the bus number to the total vehicles number, (1) the traffic with the proposed bus lane has less lane-changing conflict and can provide higher traffic capacity than the ordinary traffic without a bus lane, (2) compared with the DBL, the proposed bus lane is advantageous in easing congestion on the ordinary lanes when the traffic flow is high and can avoid unreasonable allocation of the road resources.

Shuttle bus services quality assessment Tangerang Selatan toward smart city

NASA Astrophysics Data System (ADS)

Fassa, Ferdinand; Sitorus, Fredy Jhon Philip; Adikesuma, Tri Nugraha

2017-11-01

Around the world, shuttle bus operation played the significant role to accommodate transportation for commuting bus passengers. Shuttle Bus services in cities are provided by various bus agencies with kinds of own specific purposes. For instance, at Tangerang Selatan, Indonesia, it was said that shuttle bus In Trans Bintaro is run and operated by private bus companies hire by Bintaro developer. The aim of this research is to identify factors of satisfaction of shuttle bus service in Kota Tangerang Selatan, Indonesia. Several factors are used to analyze sums of 20 parameters performance indicators of Shuttle Bus. A face to face interview using a questionnaire (N=200) was used to collect data on October and March 2017. Likert and diagram Cartesian were used to model the all the parameters. This research succeeded in finding some categories of Shuttle bus service attributes such as accessibility, comfort, and safety. Users agreed that eight indicators in shuttle bus have the excellent achievement, while three indicators on performance remain low and should receive more attention especially punctuality of the bus.

Investigation of the part-load performance of two 1.12 MW regenerative marine gas turbines

NASA Astrophysics Data System (ADS)

Korakianitis, T.; Beier, K. J.

1994-04-01

Regenerative and intercooled-regenerative gas turbine engines with low pressure ratio have significant efficiency advantages over traditional aero-derivative engines of higher pressure ratios, and can compete with modern diesel engines for marine propulsion. Their performance is extremely sensitive to thermodynamic-cycle parameter choices and the type of components. The performances of two 1.12 MW (1500 hp) regenerative gas turbines are predicted with computer simulations. One engine has a single-shaft configuration, and the other has a gas-generator/power-turbine combination. The latter arrangement is essential for wide off-design operating regime. The performance of each engine driving fixed-pitch and controllable-pitch propellers, or an AC electric bus (for electric-motor-driven propellers) is investigated. For commercial applications the controllable-pitch propeller may have efficiency advantages (depending on engine type and shaft arrangements). For military applications the electric drive provides better operational flexibility.

A New Integrated Onboard Charger and Accessory Power Converter for Plug-in Electric Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Gui-Jia; Tang, Lixin

2014-01-01

In this paper, a new approach is presented for integrating the function of onboard battery charging into the traction drive system and accessory dc-dc converter of a plug-in electric vehicle (PEV). The idea is to utilize the segmented traction drive system of a PEV as the frond converter of the charging circuit and the transformer and high voltage converter of the 14 V accessory dc-dc converter to form a galvanically isolated onboard charger. Moreover, a control method is presented for suppressing the battery current ripple component of twice the grid frequency with the reduced dc bus capacitor in the segmentedmore » inverter. The resultant integrated charger has lower cost, weight, and volume than a standalone charger due to a substantially reduced component count. The proposed integrated charger topology was verified by modeling and experimental results on a 5.8 kW charger prototype.« less

An Optimization Model for the Selection of Bus-Only Lanes in a City.

PubMed

Chen, Qun

2015-01-01

The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

78 FR 17995 - Agency Information Collection Activity Under OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-25

... collections: 49 U.S.C. Section 5337--State of Good Repair Program 49 U.S.C. Section 5339--Bus and Bus... on a quarterly basis. The information submitted ensures FTA's compliance with applicable federal laws. Title: 49 U.S.C. Section 5339--Bus and Bus Facilities Program. Abstract: 49 U.S.C. 5339--Bus and Bus...

Controller for a High-Power, Brushless dc Motor

NASA Technical Reports Server (NTRS)

Fleming, David J.; Makdad, Terence A.

1987-01-01

Driving and braking torques controllable. Control circuit operates 7-kW, 45-lb-ft (61-N-m), three-phase, brushless dc motor in both motor and generator modes. In motor modes, energy from power source is pulse-width modulated to motor through modified "H-bridge" circuit, in generator mode, energy from motor is pulse-width modulated into bank of load resistors to provide variable braking torques. Circuit provides high-resolution torque control in both directions over wide range of speeds and torques. Tested successfully at bus voltages up to 200 Vdc and currents up to 45 A.

Hybrid electric vehicle power management system

DOEpatents

Bissontz, Jay E.

2015-08-25

Level voltage levels/states of charge are maintained among a plurality of high voltage DC electrical storage devices/traction battery packs that are arrayed in series to support operation of a hybrid electric vehicle drive train. Each high voltage DC electrical storage device supports a high voltage power bus, to which at least one controllable load is connected, and at least a first lower voltage level electrical distribution system. The rate of power transfer from the high voltage DC electrical storage devices to the at least first lower voltage electrical distribution system is controlled by DC-DC converters.

Using Map Service API for Driving Cycle Detection for Wearable GPS Data: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Lei; Gonder, Jeffrey D

Following advancements in smartphone and portable global positioning system (GPS) data collection, wearable GPS data have realized extensive use in transportation surveys and studies. The task of detecting driving cycles (driving or car-mode trajectory segments) from wearable GPS data has been the subject of much research. Specifically, distinguishing driving cycles from other motorized trips (such as taking a bus) is the main research problem in this paper. Many mode detection methods only focus on raw GPS speed data while some studies apply additional information, such as geographic information system (GIS) data, to obtain better detection performance. Procuring and maintaining dedicatedmore » road GIS data are costly and not trivial, whereas the technical maturity and broad use of map service application program interface (API) queries offers opportunities for mode detection tasks. The proposed driving cycle detection method takes advantage of map service APIs to obtain high-quality car-mode API route information and uses a trajectory segmentation algorithm to find the best-matched API route. The car-mode API route data combined with the actual route information, including the actual mode information, are used to train a logistic regression machine learning model, which estimates car modes and non-car modes with probability rates. The experimental results show promise for the proposed method's ability to detect vehicle mode accurately.« less

Interprocessor bus switching system for simultaneous communication in plural bus parallel processing system

DOEpatents

Atac, R.; Fischler, M.S.; Husby, D.E.

1991-01-15

A bus switching apparatus and method for multiple processor computer systems comprises a plurality of bus switches interconnected by branch buses. Each processor or other module of the system is connected to a spigot of a bus switch. Each bus switch also serves as part of a backplane of a modular crate hardware package. A processor initiates communication with another processor by identifying that other processor. The bus switch to which the initiating processor is connected identifies and secures, if possible, a path to that other processor, either directly or via one or more other bus switches which operate similarly. If a particular desired path through a given bus switch is not available to be used, an alternate path is considered, identified and secured. 11 figures.

Interprocessor bus switching system for simultaneous communication in plural bus parallel processing system

DOEpatents

Atac, Robert; Fischler, Mark S.; Husby, Donald E.

1991-01-01

A bus switching apparatus and method for multiple processor computer systems comprises a plurality of bus switches interconnected by branch buses. Each processor or other module of the system is connected to a spigot of a bus switch. Each bus switch also serves as part of a backplane of a modular crate hardware package. A processor initiates communication with another processor by identifying that other processor. The bus switch to which the initiating processor is connected identifies and secures, if possible, a path to that other processor, either directly or via one or more other bus switches which operate similarly. If a particular desired path through a given bus switch is not available to be used, an alternate path is considered, identified and secured.

Traveling by Bus Instead of Car on Urban Major Roads: Safety Benefits for Vehicle Occupants, Pedestrians, and Cyclists.

PubMed

Morency, Patrick; Strauss, Jillian; Pépin, Félix; Tessier, François; Grondines, Jocelyn

2018-04-01

Some studies have estimated fatality and injury rates for bus occupants, but data was aggregated at the country level and made no distinction between bus types. Also, injured pedestrians and cyclists, as a result of bus travel, were overlooked. We compared injury rates for car and city bus occupants on specific urban major roads, as well as the cyclist and pedestrian injuries associated with car and bus travel. We selected ten bus routes along major urban arterials (in Montreal, Canada). Passenger-kilometers traveled were estimated from vehicle counts at intersections (2002-2010) and from bus passenger counts (2008). Police accident reports (2001-2010) provided injury data for all modes. Injury rates associated with car and bus travel were calculated for vehicle occupants, pedestrians, and cyclists. Injury rate ratios were also computed. The safety benefits of bus travel, defined as the number of vehicle occupant, cyclist, and pedestrian injuries saved, were estimated for each route. Overall, for all ten routes, the ratio between car and bus occupant injury rates is 3.7 (95% CI [3.4, 4.0]). The rates of pedestrian and cyclist injuries per hundred million passenger-kilometers are also significantly greater for car travel than that for bus travel: 4.1 (95% CI [3.5, 4.9]) times greater for pedestrian injuries; 5.3 (95% CI [3.8, 7.6]) times greater for cyclist injuries. Similar results were observed for fatally and severely injured vehicle occupants, cyclists, and pedestrians. At the route level, the safety benefits of bus travel increase with the difference in injury rate associated with car and bus travel but also with the amount of passenger-kilometers by bus. Results show that city bus is a safer mode than car, for vehicle occupants but also for cyclists and pedestrians traveling along these bus routes. The safety benefits of bus travel greatly vary across urban routes; this spatial variation is most likely linked to environmental factors. Understanding the safety benefits of public transit for specific transport routes is likely to provide valuable information for mobilizing city and transportation planners.

Propulsion system for a motor vehicle using a bidirectional energy converter

DOEpatents

Tamor, Michael Alan; Gale, Allan Roy

1999-01-01

A motor vehicle propulsion system includes an electrical energy source and a traction motor coupled to receive electrical energy from the electrical energy source. The system also has a first bus provided electrical energy by the electrical energy source and a second bus of relatively lower voltage than the first bus. In addition, the system includes an electrically-driven source of reaction gas for the electrical energy source, the source of reaction gas coupled to receive electrical energy from the first bus. Also, the system has an electrical storage device coupled to the second bus for storing electrical energy at the lower voltage. The system also includes a bidirectional energy converter coupled to convert electrical energy from the first bus to the second bus and from the second bus to the first bus.

Asymptotically zero power charge-recycling bus architecture for battery-operated ultrahigh data rate ULSI's

NASA Astrophysics Data System (ADS)

Yamauchi, Hiroyuki; Akamatsu, Hironori; Fujita, Tsutomu

1995-04-01

An asymptotically zero power charge recycling bus (CRB) architecture, featuring virtual stacking of the individual bus-capacitance into a series configuration between supply voltage and ground, has been proposed. This CRB architecture makes it possible to reduce not only each bus-swing but also a total equivalent bus-capacitance of the ultramultibit buses running in parallel. The voltage swing of each bus is given by the recycled charge-supplying from the upper adjacent bus capacitance, instead of the power line. The dramatical power reduction was verified by the simulated and measured data. According to these data, the ultrahigh data rate of 25.6 Gb/s can be achieved while maintaining the power dissipation to be less than 100 mW, which corresponds to less than 10% that of the previously reported 0.9 V suppressed bus-swing scheme, at V(sub cc) = 3.6 V for the bus width of 512 b with the bus-capacitance of 14 pF per bit operating at 50 MHz.

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes

PubMed Central

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes. PMID:26294903

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes.

PubMed

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes.

BBIS: Beacon Bus Information System

NASA Astrophysics Data System (ADS)

Kasim, Shahreen; Hafit, Hanayanti; Pei Juin, Kong; Afizah Afif, Zehan; Hashim, Rathiah; Ruslai, Husni; Jahidin, Kamaruzzaman; Syafwan Arshad, Mohammad

2016-11-01

Lack of bus information for example bus timetable, status of the bus and messy advertisement on bulletin board at the bus stop will give negative impact to tourist. Therefore, a real-time update bus information bulletin board provides all information needed so that passengers can save their bus information searching time. Supported with Android or iOS, Beacon Bus Information System (BBIS) provides bus information between Batu Pahat and Kluang area. BBIS is a system that implements physical web technology and interaction on demand. It built on Backend-as-a-Service, a cloud solution and Firebase non relational database as data persistence backend and syncs between user client in the real-time. People walk through bus stop with smart device and do not require any application. Bluetooth Beacon is used to achieve smart device's best performance of data sharing. Intellij IDEA 15 is one of the tools that that used to develop the BBIS system. Multi-language included front end and backend supported Integration development environment (IDE) helped to speed up integration process.

75 FR 74134 - State of Good Repair Bus and Bus Facilities Discretionary Program Funds

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-30

... public agencies, private companies engaged in public transportation, or private non-profit organizations... public transportation bus fleet, infrastructure, and equipment in a state of good repair. Grantees... DEPARTMENT OF TRANSPORTATION Federal Transit Administration State of Good Repair Bus and Bus...

49 CFR 655.4 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Carrying a firearm for security purposes. Vehicle means a bus, electric bus, van, automobile, rail car... involved is a bus, electric bus, van, or automobile, one or more vehicles (including non-FTA funded... the public transportation vehicle involved is a rail car, trolley car, trolley bus, or vessel, the...

49 CFR 655.4 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Carrying a firearm for security purposes. Vehicle means a bus, electric bus, van, automobile, rail car... involved is a bus, electric bus, van, or automobile, one or more vehicles (including non-FTA funded... the public transportation vehicle involved is a rail car, trolley car, trolley bus, or vessel, the...

Analysis of the vehicle fleet in the Kathmandu Valley for estimation of environment and climate co-benefits of technology intrusions

NASA Astrophysics Data System (ADS)

Shrestha, Shreejan Ram; Kim Oanh, Nguyen Thi; Xu, Quishi; Rupakheti, Maheswar; Lawrence, Mark G.

2013-12-01

Technologies and activities of the on-road traffic fleets, including bus, van, 3-wheeler, taxi and motorcycle (MC) in the Kathmandu Valley, Nepal, during 2010, were investigated with the aim to produce emission estimates, using the International Vehicle Emission (IVE) model, for the base year and for an optimistic technology scenario. The parking lot survey, GPS monitoring and video camera monitoring were conducted over four typical road types (arterial, highway, residential and outskirt roads). The average age of vehicles in the bus, van, 3-wheeler, taxi and MC fleet was 9, 8.7, 11, 9.5 and 4 years, respectively. There were some extremely old buses (over 40 years old) which had extremely high emission factors. Except for MCs that had a large share of Euro III technology (75%), other types of surveyed vehicles were at most Euro II or lower. The average vehicle kilometers traveled (VKT) for each vehicle type was estimated based on odometer readings which showed comparable results with the GPS survey. The emission factors (EFs) produced by the IVE model for the driving and meteorological conditions in Kathmandu were used to estimate emissions for the base case of 2010. EFs in Kathmandu were higher than other developing cities, especially for PM and NOx from the bus fleet. Diurnal variations of the emissions were consistent with the diurnal vehicle density. From the fleet in 2010, total emissions of the major pollutants, i.e., CO, VOC, NOx, PM, BC, and CO2, were 31, 7.7, 16, 4.7, 2.1, and 1554 Gg, respectively. If the entire fleet in the Kathmandu Valley would comply with Euro III then the emission would decrease, as compared to the base case, by 44% for toxic air pollutants (excluding CO2) and 31% for climate-forcers in terms of the 20-year horizon CO2-equivalent. Future surveys should include other vehicle types such as trucks, personal cars, and non-road vehicles. The EFs obtained for the Euro III scenario in Kathmandu were well above those in other parts of the World, hence strongly suggesting influences of the driving conditions, especially the low vehicle speeds, on the vehicle emission in the valley.

76 FR 68819 - State of Good Repair Bus and Bus Facilities Discretionary Program Funds

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-07

... that are public agencies, private companies engaged in public transportation, or private non-profit... Table 1 will provide funds to help maintain the nation's public transportation bus fleet, infrastructure... DEPARTMENT OF TRANSPORTATION Federal Transit Administration State of Good Repair Bus and Bus...

Bus Training Handbook.

ERIC Educational Resources Information Center

Dorny, Audrea; Cole, ChiKay

This manual presents guidelines for teaching students with disabilities necessary skills for safe and independent travel on public buses. Six guidelines for teachers include: (1) participate in bus training; (2) use wise and intelligent judgment; (3) utilize the bus checklist; (4) know and teach bus rules; (5) know bus routes; and (6) know bus…

49 CFR 655.4 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Carrying a firearm for security purposes. Vehicle means a bus, electric bus, van, automobile, rail car... involved is a bus, electric bus, van, or automobile, one or more vehicles (including non-FTA funded... the mass transit vehicle involved is a rail car, trolley car, trolley bus, or vessel, the mass transit...

49 CFR 655.4 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Carrying a firearm for security purposes. Vehicle means a bus, electric bus, van, automobile, rail car... involved is a bus, electric bus, van, or automobile, one or more vehicles (including non-FTA funded... the mass transit vehicle involved is a rail car, trolley car, trolley bus, or vessel, the mass transit...

49 CFR 655.4 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Carrying a firearm for security purposes. Vehicle means a bus, electric bus, van, automobile, rail car... involved is a bus, electric bus, van, or automobile, one or more vehicles (including non-FTA funded... the mass transit vehicle involved is a rail car, trolley car, trolley bus, or vessel, the mass transit...

Forecast analysis of optical waveguide bus performance

NASA Technical Reports Server (NTRS)

Ledesma, R.; Rourke, M. D.

1979-01-01

Elements to be considered in the design of a data bus include: architecture; data rate; modulation, encoding, detection; power distribution requirements; protocol, work structure; bus reliability, maintainability; interterminal transmission medium; cost; and others specific to application. Fiber- optic data bus considerations for a 32 port transmissive star architecture, are discussed in a tutorial format. General optical-waveguide bus concepts, are reviewed. The electrical and optical performance of a 32 port transmissive star bus, and the effects of temperature on the performance of optical-waveguide buses are examined. A bibliography of pertinent references and the bus receiver test results are included.

Massachusetts Fuel Cell Bus Project: Demonstrating a Total Transit Solution for Fuel Cell Electric Buses in Boston

DOE Office of Scientific and Technical Information (OSTI.GOV)

The Federal Transit Administration's National Fuel Cell Bus Program focuses on developing commercially viable fuel cell bus technologies. Nuvera is leading the Massachusetts Fuel Cell Bus project to demonstrate a complete transit solution for fuel cell electric buses that includes one bus and an on-site hydrogen generation station for the Massachusetts Bay Transportation Authority (MBTA). A team consisting of ElDorado National, BAE Systems, and Ballard Power Systems built the fuel cell electric bus, and Nuvera is providing its PowerTap on-site hydrogen generator to provide fuel for the bus.

Electrical system architecture

DOEpatents

Algrain, Marcelo C [Peoria, IL; Johnson, Kris W [Washington, IL; Akasam, Sivaprasad [Peoria, IL; Hoff, Brian D [East Peoria, IL

2008-07-15

An electrical system for a vehicle includes a first power source generating a first voltage level, the first power source being in electrical communication with a first bus. A second power source generates a second voltage level greater than the first voltage level, the second power source being in electrical communication with a second bus. A starter generator may be configured to provide power to at least one of the first bus and the second bus, and at least one additional power source may be configured to provide power to at least one of the first bus and the second bus. The electrical system also includes at least one power consumer in electrical communication with the first bus and at least one power consumer in electrical communication with the second bus.

School bus and children's traffic safety.

PubMed

Pan, Shu-ming; Hargarten, Stephen; Zhu, Shan-kuan

2007-08-01

There is no safer way to transport a child than a school bus. Fatal crashes involving occupants are extremely rare events in the US. In recent years, school bus transportation began to develop in China. We want to bring advanced experience on school bus safety in Western countries such as the US to developing countries. We searched the papers related to school bus safety from Medline, Chinese Scientific Journals Database and the Web of the National Highway Traffic Safety Administration (NHTSA). There were only 9 papers related to school bus safety, which showed that higher levels of safety standards on school buses, school bus-related transportation and environmental laws and injury prevention were the primary reasons for the desired outcome. Few school bus is related to deaths and injuries in the developed countries. The developing countries should make strict environmental laws and standards on school bus safety to prevent children's injury and death.

Compliance with driver's license laws and illegal licensing among commercial bus drivers in Lagos, Nigeria: policy implications and evidence for action.

PubMed

Okafor, I P; Odeyemi, K A; Dolapo, D C; Adegbola, A A

2014-09-01

To determine the level of compliance with driver's license laws among commercial bus drivers in Lagos, Nigeria. Two intercity motor parks were selected by simple random sampling and all consenting minibus drivers participated in the study. Key Informant Interviews (KIIs) were also conducted with selected officials in the driver training and licensing authorities. Compliance with the minimum age for driving was high (93.6%), so also was having driving test prior to driver's license procurement (83.3%). Formal driver training and VA testing were very low, (26.1% and 32.9% respectively) Overall, only 9.3% of them were found to have fulfilled all the pre-license obligations before obtaining their first driver's license. The odds of a driver with a secondary education having formal driver training is 3.33 times higher than those with no education (OR 3.33, 95% CI 1.01-11.35). Drivers who were 60 years or older were 3.62 times more likely to be compliant than those who were between 20-29 years (OR 3.62, 95% CI 0.56-29.19). For the 98.3% of them who possessed valid licenses, 52.3% of them obtained them illegally. All the key officials saw RTIs as a serious public health problem but faced several challenges in the course of their work. Overall compliance with pre-license regulations was very poor. There is need for a review and strict enforcement of driver's license laws to improve compliance. Also vital are fostering inter-sectoral collaboration and improvement in the operations of all establishments involved in driver training and license procurement in Nigeria.

Methodology for the analysis of pollutant emissions from a city bus

NASA Astrophysics Data System (ADS)

Armas, Octavio; Lapuerta, Magín; Mata, Carmen

2012-04-01

In this work a methodology is proposed for measurement and analysis of gaseous emissions and particle size distributions emitted by a diesel city bus during its typical operation under urban driving conditions. As test circuit, a passenger transportation line at a Spanish city was used. Different ways for data processing and representation were studied and, derived from this work, a new approach is proposed. The methodology was useful to detect the most important uncertainties arising during registration and processing of data derived from a measurement campaign devoted to determine the main pollutant emissions. A HORIBA OBS-1300 gas analyzer and a TSI engine exhaust particle spectrometer were used with 1 Hz frequency data recording. The methodology proposed allows for the comparison of results (in mean values) derived from the analysis of either complete cycles or specific categories (or sequences). The analysis by categories is demonstrated to be a robust and helpful tool to isolate the effect of the main vehicle parameters (relative fuel-air ratio and velocity) on pollutant emissions. It was shown that acceleration sequences have the highest contribution to the total emissions, whereas deceleration sequences have the least.

Modeling the effect of bus stops on capacity of curb lane

NASA Astrophysics Data System (ADS)

Luo, Qingyu; Zheng, Tianyao; Wu, Wenjing; Jia, Hongfei; Li, Jin

With the increase of buses and bus lines, a negative effect on road section capacity is made by the prolonged delay and queuing time at bus stops. However, existing methods of measuring the negative effect pay little attention to different bus stop types in the curb lanes. This paper uses Gap theory and Queuing theory to build models for effect-time and potential capacity in different conditions, including curbside bus stops, bus bays with overflow and bus bays without overflow. In order to make the effect-time models accurate and reliable, two types of probabilities are introduced. One is the probability that the dwell time is less than the headway of curb lane at curbside bus stops; the other is the overflow probability at bus bays. Based on the fundamental road capacity model and effect-time models, potential capacity models of curb lane are designed. The new models are calibrated by the survey data from Changchun City, and verified by the simulation software of VISSIM. Furthermore, with different arrival rates of vehicles, the setting conditions of bus stops are researched. Results show that the potential capacity models have high precision. They can offer a reference for recognizing the effect of bus stops on the capacity of curb lane, which can provide a basis for planning, design and management of urban roads and bus stops.

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

Electric School Bus Testing | Transportation Research | NREL

Science.gov Websites

Electric School Bus Evaluation Electric School Bus Evaluation Photo of children boarding school bus . NREL is evaluating the performance of electric and conventional school buses operated by two California school districts. Photo courtesy of School Bus Fleet Magazine NREL is evaluating the in-service

Classroom Activities in School Bus and Pedestrian Safety Education. Bulletin No. 93138.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Transportation, Madison.

School bus and related pedestrian safety education is prevention-oriented so that students will learn how to avoid bus-related accidents. This manual provides lesson plans emphasizing the school bus stop, loading and unloading zones, emergency evacuation drills, and appropriate behavior on the school bus. The guide also recognizes demographic…

Emission inventory estimation of an intercity bus terminal.

PubMed

Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

2016-06-01

Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

TMS communications software. Volume 2: Bus interface unit

NASA Technical Reports Server (NTRS)

Gregor, P. J.

1979-01-01

A data bus communication system to support the space shuttle's Trend Monitoring System (TMS) and to provide a basis for evaluation of the bus concept is described. Installation of the system included developing both hardware and software interfaces between the bus and the specific TMS computers and terminals. The software written for the microprocessor-based bus interface units is described. The software implements both the general bus communications protocol and also the specific interface protocols for the TMS computers and terminals.

Fault-tolerant processing system

NASA Technical Reports Server (NTRS)

Palumbo, Daniel L. (Inventor)

1996-01-01

A fault-tolerant, fiber optic interconnect, or backplane, which serves as a via for data transfer between modules. Fault tolerance algorithms are embedded in the backplane by dividing the backplane into a read bus and a write bus and placing a redundancy management unit (RMU) between the read bus and the write bus so that all data transmitted by the write bus is subjected to the fault tolerance algorithms before the data is passed for distribution to the read bus. The RMU provides both backplane control and fault tolerance.

Analysis of real-time variables affecting children's exposure to diesel-related pollutants during school bus commutes in Los Angeles

NASA Astrophysics Data System (ADS)

Sabin, Lisa D.; Kozawa, Kathleen; Behrentz, Eduardo; Winer, Arthur M.; Fitz, Dennis R.; Pankratz, David V.; Colome, Steven D.; Fruin, Scott A.

Variables affecting children's exposure during school bus commutes were investigated using real-time measurements of black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PB-PAH) and nitrogen dioxide (NO 2) inside 3 conventional diesel school buses, a particle trap-outfitted (TO) diesel school bus and a compressed natural gas (CNG) school bus, while traveling along an urban Los Angeles Unified School District bus route. A video camera was mounted at the front of each bus to record roadway conditions ahead of the bus during each commute. The videotapes from 12 commutes, in conjunction with pollutant concentration time series, were used to determine the influence of variables such as vehicles being followed, bus type and roadway type on pollutant concentrations inside the bus. For all buses tested, the highest concentrations of BC, PB-PAH and NO 2 were observed when following a diesel school bus, especially if that bus was emitting visible exhaust. This result was important because other diesel school buses were responsible for the majority of the diesel vehicle encounters, primarily due to caravanning with each other when leaving a school at the same time. Compared with following a gasoline vehicle or no target, following a smoky diesel school bus yielded BC and PB-PAH concentrations inside the cabin 8 and 11 times higher, respectively, with windows open, and ˜1.8 times higher for both pollutants with windows closed. When other diesel vehicles were not present, pollutant concentrations were highest inside the conventional diesel buses and lowest inside the CNG bus, while the TO diesel bus exhibited intermediate concentrations. Differences in pollutant concentrations between buses were most pronounced with the bus windows closed, and were attributed to a combination of higher concentrations in the exhaust and higher exhaust gas intrusion rates for the conventional diesel buses. Conventional diesel school buses can have a double exposure impact on commuting children: first, exposures to the exhaust from other nearby diesel school buses and, second, exposure to the bus's own exhaust through "self-pollution".

Integer programming model for optimizing bus timetable using genetic algorithm

NASA Astrophysics Data System (ADS)

Wihartiko, F. D.; Buono, A.; Silalahi, B. P.

2017-01-01

Bus timetable gave an information for passengers to ensure the availability of bus services. Timetable optimal condition happened when bus trips frequency could adapt and suit with passenger demand. In the peak time, the number of bus trips would be larger than the off-peak time. If the number of bus trips were more frequent than the optimal condition, it would make a high operating cost for bus operator. Conversely, if the number of trip was less than optimal condition, it would make a bad quality service for passengers. In this paper, the bus timetabling problem would be solved by integer programming model with modified genetic algorithm. Modification was placed in the chromosomes design, initial population recovery technique, chromosomes reconstruction and chromosomes extermination on specific generation. The result of this model gave the optimal solution with accuracy 99.1%.

Electrical system architecture having high voltage bus

DOEpatents

Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL

2011-03-22

An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Lijuan; Gonder, Jeff; Burton, Evan

This study evaluates the costs and benefits associated with the use of a plug-in hybrid electric bus and determines the cost effectiveness relative to a conventional bus and a hybrid electric bus. A sensitivity sweep analysis was performed over a number of a different battery sizes, charging powers, and charging stations. The net present value was calculated for each vehicle design and provided the basis for the design evaluation. In all cases, given present day economic assumptions, the conventional bus achieved the lowest net present value while the optimal plug-in hybrid electric bus scenario reached lower lifetime costs than themore » hybrid electric bus. The study also performed parameter sensitivity analysis under low market potential assumptions and high market potential assumptions. The net present value of plug-in hybrid electric bus is close to that of conventional bus.« less

Design of a CAN bus interface for photoelectric encoder in the spaceflight camera

NASA Astrophysics Data System (ADS)

Sun, Ying; Wan, Qiu-hua; She, Rong-hong; Zhao, Chang-hai; Jiang, Yong

2009-05-01

In order to make photoelectric encoder usable in a spaceflight camera which adopts CAN bus as the communication method, CAN bus interface of the photoelectric encoder is designed in this paper. CAN bus interface hardware circuit of photoelectric encoder consists of CAN bus controller SJA 1000, CAN bus transceiver TJA1050 and singlechip. CAN bus interface controlling software program is completed in C language. A ten-meter shield twisted pair line is used as the transmission medium in the spaceflight camera, and speed rate is 600kbps.The experiments show that: the photoelectric encoder with CAN bus interface which has the advantages of more reliability, real-time, transfer rate and transfer distance overcomes communication line's shortcomings of classical photoelectric encoder system. The system works well in automatic measuring and controlling system.

Working conditions of bus drivers in the private sector and bus crashes in Kandy district, Sri Lanka: a case-control study.

PubMed

Jayatilleke, A U; Nakahara, S; Dharmaratne, S D; Jayatilleke, A C; Poudel, K C; Jimba, M

2009-04-01

To explore the effects of working conditions of private-bus drivers on bus crashes in Kandy district, Sri Lanka. A case-control study was carried out from August to September 2006. All private-bus drivers registered in Kandy district and involved in crashes reported to the police between November 2005 and April 2006 (n = 63) were selected as cases. Two control groups were included: private-bus drivers working on the same routes as the case drivers (n = 90) and private-bus drivers selected randomly from other routes of the district (n = 111). Data were collected using an anonymous self-administered questionnaire. Associations between working conditions and crashes were analysed using logistic regression. A strong association was observed between drivers' disagreements about working hours and bus crashes (matched controls, adjusted odds ratio (AOR) 5.98, 95% CI 1.02 to 34.90; unmatched controls, AOR 18.74, 95% CI 2.00 to 175.84). A significant association was also observed between low salaries (

Determination of an Optimal Commercial Data Bus Architecture for a Flight Data System

NASA Technical Reports Server (NTRS)

Crawford, Kevin; Johnson, Martin; Humphries, Rick (Technical Monitor)

2001-01-01

NASA/Marshall Space Flight Center (MSFC) is continually looking for methods to reduce cost and schedule while keeping the quality of work high. MSFC is NASA's lead center for space transportation and microgravity research. When supporting NASA's programs several decisions concerning the avionics system must be made. Usually many trade studies must be conducted to determine the best ways to meet the customer's requirements. When deciding the flight data system, one of the first trade studies normally conducted is the determination of the data bus architecture. The schedule, cost, reliability, and environments are some of the factors that are reviewed in the determination of the data bus architecture. Based on the studies, the data bus architecture could result in a proprietary data bus or a commercial data bus. The cost factor usually removes the proprietary data bus from consideration. The commercial data bus's range from Versa Module Eurocard (VME) to Compact PCI to STD 32 to PC 104. If cost, schedule and size are prime factors, VME is usually not considered. If the prime factors are cost, schedule, and size then Compact PCI, STD 32 and PC104 are the choices for the data bus architecture. MSFC's center director has funded a study from his discretionary fund to determine an optimal low cost commercial data bus architecture. The goal of the study is to functionally and environmentally test Compact PCI, STD 32 and PC 104 data bus architectures. This paper will summarize the results of the data bus architecture study.

The effect of commuting microenvironment on commuter exposures to vehicular emission in Hong Kong

NASA Astrophysics Data System (ADS)

Chan, L. Y.; Chan, C. Y.; Qin, Y.

Vehicular exhaust emission has gradually become the major air pollution source in modern cities and traffic related exposure is found to contribute significantly to total human exposure level. A comprehensive survey was conducted from November 1995 to July 1996 in Hong Kong to assess the effect of traffic-induced air pollution inside different commuting microenvironments on commuter exposure. Microenvironmental monitoring is performed for six major public commuting modes (bus, light bus, MTR, railway, tram, ferry), plus private car and roadside pavement. Traffic-related pollutants, CO, NO x, THC and O 3 were selected as the target pollutants. The results indicate that commuter exposure is highly influenced by the choice of commuting microenvironment. In general, the exposure level in decreasing order of measured pollutant level for respective commuting microenvironments are: private car, the group consisting light bus, bus, tram and pavement, MTR and train, and finally ferry. In private car, the CO level is several times higher than that in the other microenvironments with a trip averaged of 10.1 ppm and a maximum of 24.9 ppm. Factors such as the body position of the vehicle, intake point of the ventilation system, fuel used, ventilation, transport mode, road and driving conditions were used in the analysis. Inter-microenvironment, intra-microenvironment and temporal variation of CO concentrations were used as the major indicator. The low body position and low intake point of the ventilation system of the private car are believed to be the cause of higher intake of exhaust of other vehicles and thus result in high pollution level in this microenvironment. Compared with other metropolis around the world and the Hong Kong Air Quality Objectives (HKAQO), exposure levels of commuter to traffic-related air pollution in Hong Kong are relatively low for most pollutants measured. Only several cases of exceedence of HKAQO by NO 2 were recorded. The strong prevailing wind plus the channeling effect created by the harbor, the fuel used, the relative abundance of new cars and the successful implementation of the vehicle emission control program are factors that compensate the effect of the emission source strength and thus lead to low exposure levels.

Assessing factors causing severe injuries in crashes of high-deck buses in long-distance driving on freeways.

PubMed

Chu, Hsing-Chung

2014-01-01

High-deck buses that have a higher center of gravity traveling at an excessive speed have a higher likelihood of causing serious and fatal accidents when drivers lose control of the vehicle. In addition, drivers who suffer from fatigue in long-distance driving increase the likelihood of serious accident. This paper examines the effects of risk factors contributing to severe crashes associated with high-deck buses used for long-distance driving on freeways. An ordered logit and latent class models are used to examine significant factors on the severity of injuries in crashes related to high-deck buses. Driver fatigue, drivers or passengers not wearing a seat belt, reckless driving, drunk driving, crashes occurred between midnight and dawn, and crashes occurred at interchange ramps were found to significantly affect the severity of injuries in crashes involving high-deck buses. Safety policies to prevent severe injuries in crashes involving high deck buses used for long-distance runs on freeways include: (1) restricting drivers from exceeding the limit of daily driving hours and mandating sufficient rest breaks; (2) installing an automatic sleep-warning device in the vehicle; (3) drivers with obstructive sleep apnea syndrome or sleep disorders should be tested and treated before they are allowed to perform long hours of driving tasks; (4) educating the public or even amending the seatbelt legislation to require all passengers to wear a seat belt and thus reduce the chance of ejection from a high-deck bus and prevent serious injuries in a crash while traveling at a higher speed on freeways. Copyright © 2013 Elsevier Ltd. All rights reserved.

77 FR 27277 - FTA Supplemental Fiscal Year 2012 Apportionments, Allocations, and Program Information

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-09

... allocates Section 5309 Bus and Bus Facilities funds to bus testing and the Fuel Cell program. Tables... Fuel Cell program. FTA will issue a supplemental notice at a later date if additional contract... allocated CA, GA, MA E2012-BUSP-018 Fuel Cell Bus Program..... $13,500,000 PA E2012-BUSP-019 Bus Testing 3...

40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 19 2014-07-01 2014-07-01 false Maintenance of records for urban bus... SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal of information; right of entry. (a) The operator of any urban bus for which this subpart is...

40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 19 2012-07-01 2012-07-01 false Maintenance of records for urban bus... SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal of information; right of entry. (a) The operator of any urban bus for which this subpart is...

40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 19 2013-07-01 2013-07-01 false Maintenance of records for urban bus... SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal of information; right of entry. (a) The operator of any urban bus for which this subpart is...

40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 18 2011-07-01 2011-07-01 false Maintenance of records for urban bus... SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal of information; right of entry. (a) The operator of any urban bus for which this subpart is...

Modal split model considering carpool mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyles, R.W.

1979-03-01

Modal split remains a primary concern of transportation planners as the state-of-the art has developed from diversion curves to behavioral models. The approach taken here is to formulate the mode-choice decision for the work trip as a linear combination of real and perceived characteristics of the modes considered. The logit formulation is used with three modes being considered: two automobile modes (drive-alone and carpool) and a public transit mode (bus). The final model provides insight into which factors are important in travel decisions among these three modes and the importance of examining traveler's perceptions of the differences among modes relativemore » to actual measurable differences.« less

[The path to customized prosthesis: role of the occupational therapist in the recovery of autonomy].

PubMed

Fogliaresi, Stefania; Mulè, Chiara; Borboni, Alberto; Taveggia, Giovanni

2015-01-01

The aim of the rehabilitative treatment of the amputee is to facilitate the reintegration of the patient into daily life: within social, family, and working contexts. Occupational therapy relates to 'doing', to everyday life. These are the activities carried out by individuals during daily life: catching the bus, driving a car, cooking a meal, playing cards or changing a light bulb. During the process of rehabilitation of the amputee the occupational therapist must evaluate the residual capacities of the patient, discover their needs and requirements so as to develop suitable rehabilitative strategiesfor retraining motor-skills, acceptance of the new living conditions, and social reintegration.

A BAPTA employing rotary transformers, stepper motors and ceramic ball bearings

NASA Technical Reports Server (NTRS)

Auer, W.

1981-01-01

The utilization of rotary transformers as an alternative to slip rings for the power transfer from solar panels to a satellite's main body could be advantageous, especially if an ac bus system is taken into consideration. Different approaches with main emphasis on the electromagnetic design were investigated and showed efficiencies of up to 99% with a 3 kW power capability. A solidly preloaded pair of ball bearings with ceramic balls assures proper transformer air gaps and acceptable torque changes over temperature and temperature gradients. The bearing and power transfer assembly is driven by a direct drive stepper motor with inherent redundancy properties and needs no caging mechanism.

Bus Stops and Pedestrian-Motor Vehicle Collisions in Lima, Peru: A Matched Case-Control Study

PubMed Central

Quistberg, D. Alex; Koepsell, Thomas D.; Johnston, Brian D.; Boyle, Linda Ng; Miranda, J. Jaime; Ebel, Beth E.

2015-01-01

Objective To evaluate the relationship between bus stop characteristics and pedestrian-motor vehicle collisions. Design Matched case-control study where the units of study were pedestrian crossing. Setting Random sample of 11 police commissaries in Lima, Peru. Data collection occurred from February, 2011 to September, 2011. Participants 97 intersection cases representing 1,134 collisions and 40 mid-block cases representing 469 collisions that occurred between October, 2010 and January, 2011 and their matched controls. Main Exposures Presence of a bus stop and specific bus stop characteristics. Main Outcome Occurrence of a pedestrian-motor vehicle collision. Results Intersections with bus stops were three times more likely to have a pedestrian-vehicle collision (OR 3.28, 95% CI 1.53-7.03), relative to intersections without bus stops. Both formal and informal bus stops were associated with a higher odds of a collision at intersections (OR 6.23, 95% CI 1.76-22.0 and OR 2.98, 1.37-6.49). At mid-block sites, bus stops on a bus-dedicated transit lane were also associated with collision risk (OR 2.36, 95% CI 1.02-5.42). All bus stops were located prior to the intersection, contrary to practices in most high income countries. Conclusions In urban Lima, the presence of a bus stop was associated with a three-fold increase in risk of a pedestrian collision. The highly competitive environment among bus companies may provide an economic incentive for risky practices such as dropping off passengers in the middle of traffic and jockeying for position with other buses. Bus stop placement should be considered to improve pedestrian safety. PMID:24357516

Development of a composite line source emission model for traffic interrupted microenvironments and its application in particle number emissions at a bus station

NASA Astrophysics Data System (ADS)

Wang, Lina; Jayaratne, Rohan; Heuff, Darlene; Morawska, Lidia

A composite line source emission (CLSE) model was developed to specifically quantify exposure levels and describe the spatial variability of vehicle emissions in traffic interrupted microenvironments. This model took into account the complexity of vehicle movements in the queue, as well as different emission rates relevant to various driving conditions (cruise, decelerate, idle and accelerate), and it utilised multi-representative segments to capture the accurate emission distribution for real vehicle flow. Hence, this model was able to quickly quantify the time spent in each segment within the considered zone, as well as the composition and position of the requisite segments based on the vehicle fleet information, which not only helped to quantify the enhanced emissions at critical locations, but it also helped to define the emission source distribution of the disrupted steady flow for further dispersion modelling. The model then was applied to estimate particle number emissions at a bi-directional bus station used by diesel and compressed natural gas fuelled buses. It was found that the acceleration distance was of critical importance when estimating particle number emission, since the highest emissions occurred in sections where most of the buses were accelerating and no significant increases were observed at locations where they idled. It was also shown that emissions at the front end of the platform were 43 times greater than at the rear of the platform. Although the CLSE model is intended to be applied in traffic management and transport analysis systems for the evaluation of exposure, as well as the simulation of vehicle emissions in traffic interrupted microenvironments, the bus station model can also be used for the input of initial source definitions in future dispersion models.

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

NASA Astrophysics Data System (ADS)

Zhang, Qunfang; Zhu, Yifang

2010-01-01

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter < 100 nm), with the highest human exposure usually occurring on and near roadways. Children are particularly at risk due to immature respiratory systems and faster breathing rates. In this study, children's exposure to in-cabin air pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children's exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM 2.5, PM 10, black carbon (BC), CO, and CO 2 levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10 3 to 3.4 × 10 4 particles cm -3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses' self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.

Driving in traffic: short-range sensing for urban collision avoidance

NASA Astrophysics Data System (ADS)

Thorpe, Chuck E.; Duggins, David F.; Gowdy, Jay W.; MacLaughlin, Rob; Mertz, Christoph; Siegel, Mel; Suppe, Arne; Wang, Chieh-Chih; Yata, Teruko

2002-07-01

Intelligent vehicles are beginning to appear on the market, but so far their sensing and warning functions only work on the open road. Functions such as runoff-road warning or adaptive cruise control are designed for the uncluttered environments of open highways. We are working on the much more difficult problem of sensing and driver interfaces for driving in urban areas. We need to sense cars and pedestrians and curbs and fire plugs and bicycles and lamp posts; we need to predict the paths of our own vehicle and of other moving objects; and we need to decide when to issue alerts or warnings to both the driver of our own vehicle and (potentially) to nearby pedestrians. No single sensor is currently able to detect and track all relevant objects. We are working with radar, ladar, stereo vision, and a novel light-stripe range sensor. We have installed a subset of these sensors on a city bus, driving through the streets of Pittsburgh on its normal runs. We are using different kinds of data fusion for different subsets of sensors, plus a coordinating framework for mapping objects at an abstract level.

Fracture toughness in Mode I (GIC) for ductile adhesives

NASA Astrophysics Data System (ADS)

Gálvez, P.; Carbas, RJC; Campilho, RDSG; Abenojar, J.; Martínez, MA; Silva LFM, da

2017-05-01

Works carried out in this publication belong to a project that seeks the replacement of welded joints by adhesive joints at stress concentration nodes in bus structures. Fracture toughness in Mode I (GIC) has been measured for two different ductile adhesives, SikaTack Drive and SikaForce 7720. SikaTack Drive is a single-component polyurethane adhesive with high viscoelasticity (more than 100%), whose main use is the car-glass joining and SikaForce 7720 is double-component structural polyurethane adhesive. Experimental works have been carried out from the test called Double Cantilever Beam (DCB), using two steel beams as adherents and an adhesive thickness according to the problem posed in the Project, of 2 and 3 mm for SikaForce 7720 and SikaTack Drive, respectively. Three different methods have been used for measuring the fracture toughness in mode I (GIC) from the values obtained in the experimental DCB procedure for each adhesive: Corrected Beam Theory (CBT), Compliance Calibration Method (CCM) and Compliance Based Beam Method (CBBM). Four DCB specimens have been tested for each adhesive. Dispersion of each GIC calculation method for each adhesive has been studied. Likewise variations between the three different methods have been also studied for each adhesive.

7. YOSEMITE VALLEY SHUTTLE BUS AT SENTINEL BRIDGE SHUTTLE BUS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. YOSEMITE VALLEY SHUTTLE BUS AT SENTINEL BRIDGE SHUTTLE BUS AND PARKING LOT AREA. LOOKING WNW. GIS: N-37 40 36.2 / W-119 44 45.0 - Yosemite National Park Roads & Bridges, Yosemite Village, Mariposa County, CA

GO Bus impact analysis.

DOT National Transportation Integrated Search

2013-08-01

NJ TRANSIT launched two relatively new enhanced bus services: GO 25 serving the : Springfield Avenue corridor in 2008 and GO 28 serving the Bloomfield Avenue corridor in 2009. : As an enhanced but not full Bus Rapid Transit (BRT) service, GO Bus feat...

Bus Crashworthiness Issues. Highway Special Investigation Report

DOT National Transportation Integrated Search

1999-09-01

School bus and motorcoach travel are two of the safest forms of transportation in the United States. Each year, on average, nine school bus passengers and four motorcoach passengers are fatally injured in bus crashes, according to the National Highwa...

Network Extender for MIL-STD-1553 Bus

NASA Technical Reports Server (NTRS)

Marcus, Julius; Hanson, T. David

2003-01-01

An extender system for MIL-STD-1553 buses transparently couples bus components at multiple developer sites. The bus network extender is a relatively inexpensive system that minimizes the time and cost of integration of avionic systems by providing a convenient mechanism for early testing without the need to transport the usual test equipment and personnel to an integration facility. This bus network extender can thus alleviate overloading of the test facility while enabling the detection of interface problems that can occur during the integration of avionic systems. With this bus extender in place, developers can correct and adjust their own hardware and software before products leave a development site. Currently resident at Johnson Space Center, the bus network extender is used to test the functionality of equipment that, although remotely located, is connected through a MILSTD- 1553 bus. Inasmuch as the standard bus protocol for avionic equipment is that of MIL-STD-1553, companies that supply MIL-STD-1553-compliant equipment to government or industry and that need long-distance communication support might benefit from this network bus extender

Transit Bus Fuel Economy and Performance Simulation

DOT National Transportation Integrated Search

1984-01-01

This report presents the results of bus simulation studies to determine the effects of various design and operating parameters on bus fuel economy and performance. The bus components are first described in terms of how they are modeled. Then a variat...

The NASA bus communications listening device software

NASA Technical Reports Server (NTRS)

Allen, M. A.

1979-01-01

The development of the bus listener is presented. Special software was developed to control the 'bus interface units' (BIU) connecting each of these devices to a communications cable to form the bus communication network. The code used in the BTU is described.

75 FR 52054 - Bus and Bus Facilities Discretionary Program Funds

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-24

... engaged in public transportation, or private non-profit organizations. FOR FURTHER INFORMATION CONTACT... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Bus and Bus Facilities Discretionary... program announcement of project selections. SUMMARY: The U.S. Department of Transportation's (DOT) Federal...

Effectiveness of Bus Signal Priority : Final Report

DOT National Transportation Integrated Search

2002-01-01

Effectiveness of Bus Signal Priority (BSP) study evaluates BSP?s impact on traffic operations. The goal was to examine how different situations, such as the level of congestion, placement of bus stops, presence of express bus service, and number of t...

American Fuel Cell Bus Project : First Analysis Report

DOT National Transportation Integrated Search

2013-06-01

This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALSTAR...

American fuel cell bus project : first analysis report.

DOT National Transportation Integrated Search

2013-06-01

This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration : funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALST...

Optical technology for flight control systems

NASA Technical Reports Server (NTRS)

Mayanagi, M.

1986-01-01

Optical applications to the flight control system including optical data bus, sensors, and transducers are analyzed. Examples of optical data bus include airborne light optical fiber technology (ALOFT), F-5E, YA-7D, MIL-STD-1553 fiber optic data bus and NAL-optic data bus. This NAL-optic data bus is applied to STOL, and its characteristics are stressed. Principles and advantages of optical pulse-digital transducers are discussed.

Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment

PubMed Central

Ngo, Nicole S.

2015-01-01

Abstract Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards by using bus vintage as a proxy for bus emissions. This is accomplished using a unique, rich panel data set, which includes daily information on bus vintage and route for the New York City Transit bus fleet between 2006 and 2009. This information is merged with daily data on emergency department (ED) visits for respiratory illnesses, which include patients’ residences at the census block level and exact admission date. Economic benefits resulting from these bus pollution policies are then estimated. Results show that stricter transit bus emission standards by the U.S. Environmental Protection Agency for particulate matter are associated with reduced ED visits for respiratory diseases for patients living within a few hundred feet of a bus route. These findings demonstrate that bus pollution policies have made critical improvements to public health. PMID:26376392

Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment.

PubMed

Ngo, Nicole S

2015-09-01

Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards by using bus vintage as a proxy for bus emissions. This is accomplished using a unique, rich panel data set, which includes daily information on bus vintage and route for the New York City Transit bus fleet between 2006 and 2009. This information is merged with daily data on emergency department (ED) visits for respiratory illnesses, which include patients' residences at the census block level and exact admission date. Economic benefits resulting from these bus pollution policies are then estimated. Results show that stricter transit bus emission standards by the U.S. Environmental Protection Agency for particulate matter are associated with reduced ED visits for respiratory diseases for patients living within a few hundred feet of a bus route. These findings demonstrate that bus pollution policies have made critical improvements to public health.

Brief Report: The Association of Graduated Driver Licensing with Nondriver Transport-related Injuries Among Adolescents.

PubMed

Zhu, Motao; Zhao, Songzhu; Long, D Leann

2016-09-01

As a phased approach to initiating driving, graduated driver licensing restricts driving by young drivers with the aim of reducing crashes. It might increase riding with parents or on buses, which might be safer, or walking or biking, which might be more dangerous. We examined whether it increases nondriver injuries, and whether it reduces total injuries combining drivers and nondrivers. We conducted longitudinal analyses of 1995-2012 traffic injuries from 43 states. Using Poisson mixed regression, we estimated adjusted rate ratios for visible, incapacitating, and fatal injury. Among 16 year olds, graduated driver licensing was associated with reduced passenger injuries (adjusted rate ratio 0.93, 95% confidence interval: 0.89, 0.97). It was not associated with increased injuries as bus riders, pedestrians, or bicyclists among 16- or 17-year olds. It was associated with a 10% reduction in total injuries among 16-year olds, but not 17-year olds. Graduated driver licensing was associated with reduced passenger injuries and total injuries.

Trends in bus transit operations, 1960-1974

DOT National Transportation Integrated Search

1977-01-01

This report analyzes the historical patterns of bus transit operations from 1960 to 1974 using data from 50 bus operations. Because of limitations on the available data, the analyzed data do not represent the universe of bus operations, nor is it a r...

Effect of bus-stop spacing on mobile emissions in urban areas.

DOT National Transportation Integrated Search

2003-01-01

The operational effect of bus-stop spacing has been a critical issue. Closely spaced bus stops : disrupt the traffic flow on the bus route, particularly during peak hours because buses make frequent stops : to provide services to customers. The disru...

Modular Cooling Components

NASA Technical Reports Server (NTRS)

Eastman, G. Yale; Dussinger, Peter M.; Hartenstine, John R.

1994-01-01

Three modular heat-transfer components designed for use together or separately. Simple mechanical connections facilitate assembly of these and related heat-transfer components into cooling systems of various configurations, such as to cool laboratory equipment rearranged for different experiments. Components are clamp-on cold plate, cold plate attached to flexible heat pipe, and thermal-bus receptacle. Clamp-on cold plate moved to any convenient location for attachment of equipment cooled by it, then clamped onto thermal bus. Heat from equipment conducted through plate and into coolant. Thermal-bus receptacle integral with thermal bus. Includes part of thermal bus to which clamp-on cold plate attached, plus tapered socket into which condenser end of flexible heat pipe plugged. Thermal-bus receptacle includes heat-pipe wick structure using coolant in bus to enhance transfer of heat from cold plate.

Relative importance of school bus-related microenvironments to children's pollutant exposure.

PubMed

Behrentz, Eduardo; Sabin, Lisa D; Winer, Arthur M; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

2005-10-01

Real-time concentrations of black carbon, particle-bound polycyclic aromatic hydrocarbons, nitrogen dioxide, and fine particulate counts, as well as integrated and real-time fine particulate matter (PM2.5) mass concentrations were measured inside school buses during long commutes on Los Angeles Unified School District bus routes, at bus stops along the routes, at the bus loading/unloading zone in front of the selected school, and at nearby urban "background" sites. Across all of the pollutants, mean concentrations during bus commutes were higher than in any other microenvironment. Mean exposures (mean concentration times time spent in a particular microenvironment) in bus commutes were between 50 and 200 times greater than those for the loading/unloading microenvironment, and 20-40 times higher than those for the bus stops, depending on the pollutant. Although the analyzed school bus commutes represented only 10% of a child's day, on average they contributed one-third of a child's 24-hr overall black carbon exposure during a school day. For species closely related to vehicle exhaust, the within- cabin exposures were generally dominated by the effect of surrounding traffic when windows were open and by the bus's own exhaust when windows were closed. Low-emitting buses generally exhibited high concentrations only when traveling behind a diesel vehicle, whereas high-emitting buses exhibited high concentrations both when following other diesel vehicles and when idling without another diesel vehicle in front of the bus. To reduce school bus commute exposures, we recommend minimizing commute times, avoiding caravanning with other school buses, using the cleanest buses for the longest bus routes, maintaining conventional diesel buses to eliminate visible emissions, and transitioning to cleaner fuels and advanced particulate control technologies as soon as possible.

Measuring self-pollution in school buses using a tracer gas technique

NASA Astrophysics Data System (ADS)

Behrentz, Eduardo; Fitz, Dennis R.; Pankratz, David V.; Sabin, Lisa D.; Colome, Steven D.; Fruin, Scott A.; Winer, Arthur M.

A potentially important, but inadequately studied, source of children's exposure to pollutants during school bus commutes is the introduction of a bus's own exhaust into the passenger compartment. We developed and applied a method to determine the amount of a bus's own exhaust penetrating into the cabin in a study of six in-use school buses over a range of routes, roadway types, fuels, and emission control technologies. A tracer gas, SF 6, was metered into the bus's exhaust system using a mass flow controller whose flow rate was logged by a data acquisition system and processed with the concurrent real-time pollutant measurement data. At the same time, the SF 6 concentration inside the bus was measured using an AeroVironment CTA-1000 continuous analyzer connected to a series of solenoids that switched the sample inlet between the front and rear of the bus cabin. To account for a baseline drift of the CTA-1000, SF 6-free air was also drawn through a line located outside at the front of the bus. Although this third sample line generally provided a reference zero value, it also showed that under certain wind conditions (i.e., wind from the rear) when the bus was stopped and was idling, significant amounts of the bus's own exhaust reached this location at the front of the bus. Self-pollution, the percentage of a bus's own exhaust that can be found inside its cabin, was a function of bus type and age, and a strong function of window position (i.e., open or closed). We estimated up to 0.3% of the air inside the cabin was from the bus's own exhaust in older buses, approximately 10 times the percentage observed for newer buses, and 25% of the black carbon concentration variance was explained by the buses' self-pollution. Analysis of the tracer gas concentrations provided a powerful tool for identifying potentially high-exposure conditions.

Transit bus life cycle cost and year 2007 emissions estimation.

DOT National Transportation Integrated Search

2007-06-01

The report presents a study of transit bus life cycle cost (LCC) analysis, and projected transit bus emissions and fuel economy for 2007 : model year buses. It covers four bus types: diesel buses using ultra low sulfur diesel (ULSD), diesel buses usi...

75 FR 20034 - Over-the-Road Bus Accessibility Program Grants: Corrections

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-16

... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Over-the-Road Bus Accessibility... ``Over-the-Road Bus Accessibility Program Grants,'' extends the application deadline, and allows... comply with the terms and conditions of the Special Warranty for the Over-the-Road Bus Accessibility...

Information management advanced development. Volume 3: Digital data bus breadboard

NASA Technical Reports Server (NTRS)

Gerber, C. R.

1972-01-01

The design, development, and evaluation of the digital data bus breadboard for the modular space station are discussed. Subjects presented are: (1) requirements summary, (2) parametric data for bus design, (3) redundancy concepts, and (4) data bus breadboard performance and interface requirements.

Large school bus design vehicle dimensions

DOT National Transportation Integrated Search

1998-09-01

A survey of United States school bus operators and manufacturers was conducted to define the larger sizes of school buses in regular use. A mid-60 passenger type-c bus (SB-C) and a mid-80 passenger type-D bus (SB-D) were selected as design vehicles. ...

National fuel cell bus program : proterra fuel cell hybrid bus report, Columbia demonstration.

DOT National Transportation Integrated Search

2011-10-01

This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by the Center for Transportation and the Environment an...

Multiple output power supply circuit for an ion engine with shared upper inverter

NASA Technical Reports Server (NTRS)

Cardwell, Jr., Gilbert I. (Inventor); Phelps, Thomas K. (Inventor)

2001-01-01

A power supply circuit for an ion engine suitable for a spacecraft is coupled to a bus having a bus input and a bus return. The power supply circuit has a first primary winding of a first transformer. An upper inverter circuit is coupled to the bus input and the first primary winding. The power supply circuit further includes a first lower inverter circuit coupled to the bus return and the first primary winding. The second primary winding of a second transformer is coupled to the upper inverter circuit. A second lower inverter circuit is coupled to the bus return and the second primary winding.

Bus accident analysis of routes with/without bus priority.

PubMed

Goh, Kelvin Chun Keong; Currie, Graham; Sarvi, Majid; Logan, David

2014-04-01

This paper summarises findings on road safety performance and bus-involved accidents in Melbourne along roads where bus priority measures had been applied. Results from an empirical analysis of the accident types revealed significant reduction in the proportion of accidents involving buses hitting stationary objects and vehicles, which suggests the effect of bus priority in addressing manoeuvrability issues for buses. A mixed-effects negative binomial (MENB) regression and back-propagation neural network (BPNN) modelling of bus accidents considering wider influences on accident rates at a route section level also revealed significant safety benefits when bus priority is provided. Sensitivity analyses done on the BPNN model showed general agreement in the predicted accident frequency between both models. The slightly better performance recorded by the MENB model results suggests merits in adopting a mixed effects modelling approach for accident count prediction in practice given its capability to account for unobserved location and time-specific factors. A major implication of this research is that bus priority in Melbourne's context acts to improve road safety and should be a major consideration for road management agencies when implementing bus priority and road schemes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Survey on the implementation and reliability of CubeSat electrical bus interfaces

NASA Astrophysics Data System (ADS)

Bouwmeester, Jasper; Langer, Martin; Gill, Eberhard

2017-06-01

This paper provides results and conclusions on a survey on the implementation and reliability aspects of CubeSat bus interfaces, with an emphasis on the data bus and power distribution. It provides recommendations for a future CubeSat bus standard. The survey is based on a literature study and a questionnaire representing 60 launched CubeSats and 44 to be launched CubeSats. It is found that the bus interfaces are not the main driver for mission failures. However, it is concluded that the Inter Integrated Circuit (I2C) data bus, as implemented in a great majority of the CubeSats, caused some catastrophic satellite failures and a vast amount of bus lockups. The power distribution may lead to catastrophic failures if the power lines are not protected against overcurrent. A connector and wiring standard widely implemented in CubeSats is based on the PC/104 standard. Most participants find the 104 pin connector of this standard too large. For a future CubeSat bus interface standard, it is recommended to implement a reliable data bus, a power distribution with overcurrent protection and a wiring harness with smaller connectors compared with PC/104.

Sensor/Transducer Bus Alternatives for Space derived from Automotive Networks

NASA Astrophysics Data System (ADS)

Heyer, H.-V.

2004-06-01

Both automotive and space industry have major constraints concerning cable and harness. As in a satellite, the dry mass of the harness in the empty car is about 3.3% of the total car mass and the harness costs are about 12% of the total production cost. So a lot of new architectural communication and power distribution concepts are needed to reduce these drawbacks. One of the possible solutions is the use of distributed bus systems which contains in a decentralized topology busses such as CAN, TTCAN or FLEX-RAY for hard-real-time applications, MOST for fast video communication via optical fiber cabling and fire wire IEEE1394 as backbone.For the general purpose sensor/actuator tasks a simple robust one-wire bus has been defined, the Local Interconnect Network (LIN) bus. This bus is an open standard which is supported by several semiconductor manufactures. The bus was firstly introduced in 1999 and has now reached an acceptable maturity with version 2.0 turning out to be quite interesting as sensor / transducer bus for space applications.This presentation will focus on the LIN Bus and present an overview of that bus.

[Investigation on events of bus on fire in 6 years in the mainland of China].

PubMed

Wang, X G; Liu, Y; Cen, Y; Wu, P; Zhou, H L; Han, C M

2016-12-20

Objective: To retrospectively analyze the characteristics of events of bus on fire in 6 years in the mainland of China. Methods: Events of bus on fire happened between January 2009 and December 2014 were retrieved through Baidu search engine, Chinese Journals Full - text Database, and PubMed database in the search strategy with " bus" and " fire" or " arson" as keywords combined with the name of provinces, autonomous regions, and municipalities of the mainland of China. The occurrence time, region, cause of fire, casualties of each event were recorded, and the correlative analysis was conducted. Data were processed with Microsoft Excel software. Results: Totally 287 events of bus on fire were retrieved, among which 49 events happened in 2009, 36 events happened in 2010, 35 events happened in 2011, 37 events happened in 2012, and respectively 65 events happened in 2013 and 2014. The events of bus on fire most frequently happened in June and July, respectively 49 and 39 events. Among the distribution of occurrence regions of events of bus on fire, there were 78 events (27.18%) in east China, 52 events (18.12%) in northeast China, 41 events (14.29%) both in north China and south China. Among the causes of events of bus on fire, spontaneous combustion of bus ranked in the first (267 events, accounting for 93.03%), followed by arson (13 events, accounting for 4.53%). Among the 13 events of bus on fire caused by arson, 7 events happened between 16: 00 and 20: 00, and 3 events happened between 8: 00 and 10: 00. Totally 27 events of bus on fire (9.41%) were with casualties, among which 13 events (48.15%) were caused by spontaneous combustion of bus, 10 events (37.04%) were caused by arson, and 4 events (14.81%) were caused by traffic accidents. Arson caused the most severe casualties (at least 88 deaths and 287 injuries), followed by spontaneous combustion of bus (at least 35 deaths and 140 injuries) and traffic accidents (at least 9 deaths and 20 injuries). Conclusions: Events of bus on fire happened more frequently in recent years in the mainland of China, and the frequencies were much higher especially in June and July. Most events were caused by spontaneous combustion of bus, followed by arson. Most of the events of bus on fire caused by arson happened in the morning and evening rush hours of urban traffic, and althouth the occurrence rate was not high, the casualties were most severe.

Short-term exposure to PM 10, PM 2.5, ultrafine particles and CO 2 for passengers at an intercity bus terminal

NASA Astrophysics Data System (ADS)

Cheng, Yu-Hsiang; Chang, Hsiao-Peng; Hsieh, Cheng-Ju

2011-04-01

The Taipei Bus Station is the main transportation hub for over 50 bus routes to eastern, central, and southern Taiwan. Daily traffic volume at this station is about 2500 vehicles, serving over 45,000 passengers daily. The station is a massive 24-story building housing a bus terminal, a business hotel, a shopping mall, several cinemas, offices, private residential suites, and over 900 parking spaces. However, air quality inside this bus terminal is a concern as over 2500 buses are scheduled to run daily. This study investigates the PM 10, PM 2.5, UFP and CO 2 levels inside and outside the bus terminal. All measurements were taken between February and April 2010. Measurement results show that coarse PM inside the bus terminal was resuspended by the movement of large numbers of passengers. The fine and ultrafine PM in the station concourse were from outside vehicles. Moreover, fine and ultrafine PM at waiting areas were exhausted directly from buses in the building. The CO 2 levels at waiting areas were likely elevated by bus exhaust and passengers exhaling. The PM 10, PM 2.5 and CO 2 levels at the bus terminal were lower than Taiwan's EPA suggested standards for indoor air quality. However, UFP levels at the bus terminal were significantly higher than those in the urban background by about 10 times. Therefore, the effects of UFPs on the health of passengers and workers must be addressed at this bus terminal since the levels of UFPs are higher than >1.0 × 10 5 particles cm -3.

Knowledge, Risk Perception and Practice Regarding Tuberculosis Transmission among Long Distance Bus Drivers in Addis Ababa, Ethiopia: A Cross Sectional Study.

PubMed

Gebrehiwot, Tsegaye Tewelde; Tesfamichael, Fessahaye Alemseged

2017-11-01

Window opening during bus transportation is recommended as a tuberculosis prevention strategy.Yet, drivers are affected by lack knowledge and risk perception of passengers and assistants. Boosting knowledge of and notifying the high risk of tuberculosis transmission for every passenger could be too costly. However, strategies targeting bus drivers as key agents unlike targeting all passengers might be less costly for window opening. Data were collected from November 18/2014 to December 21/2014 in inter-region bus stations of Addis Ababa using cross sectional study design. Samples of 306 participants were selected using simple random sampling, and data were collected through face-to-face interview. Data were entered into Epi-data version 3.1 andanalyzed using IBM SPSS version 21. From a sample of 306 bus drivers, 303 were interviewed. Nine in ten and nearly half of participants believed in the need for opening all windows and avoiding overcrowding of passengers as TB preventive measures respectively. Few bus drivers (7.3%) believed that bus drivers and their assistants could be at risk of tuberculosis. The majority (85.7%) of bus drivers opened side window the whole day without precondition. Hearing tuberculosis related information from radio was a promoting factor for tuberculosis preventive measures among bus drivers. Tuberculosis preventive practices and knowledge of bus drivers seempositive (opportunities), despite their low risk perception (challenge). Using the opportunity, further empowering bus drivers to persuade passengers and assistants to open all the rest of the windows is needed.

Analysis, operation and maintenance of a fuel cell/battery series-hybrid bus for urban transit applications

NASA Astrophysics Data System (ADS)

Bubna, Piyush; Brunner, Doug; Gangloff, John J.; Advani, Suresh G.; Prasad, Ajay K.

The fuel cell hybrid bus (FCHB) program was initiated at the University of Delaware in 2005 to demonstrate the viability of fuel cell vehicles for transit applications and to conduct research and development to facilitate the path towards their eventual commercialization. Unlike other fuel cell bus programs, the University of Delaware's FCHB design features a battery-heavy hybrid which offers multiple advantages in terms of cost, performance and durability. The current fuel cell hybrid bus is driven on a regular transit route at the University of Delaware. The paper describes the baseline specifications of the bus with a focus on the fuel cell and the balance of plant. The fuel cell/battery series-hybrid design is well suited for urban transit routes and provides key operational advantages such as hydrogen fuel economy, efficient use of the fuel cell for battery recharging, and regenerative braking. The bus is equipped with a variety of sensors including a custom-designed cell voltage monitoring system which provide a good understanding of bus performance under normal operation. Real-time data collection and analysis have yielded key insights for fuel cell bus design optimization. Results presented here illustrate the complex flow of energy within the various subsystems of the fuel cell hybrid bus. A description of maintenance events has been included to highlight the issues that arise during general operation. The paper also describes several modifications that will facilitate design improvements in future versions of the bus. Overall, the fuel cell hybrid bus demonstrates the viability of fuel cells for urban transit applications in real world conditions.

Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system [research brief].

DOT National Transportation Integrated Search

2012-03-01

Government regulators and transportation operators of public bus systems are concerned about terrorist attacks. Bus attacks in Israel between late September 2000 and the end of 2006, a period known as the Second Intifada, are particularly well known....

Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system.

DOT National Transportation Integrated Search

2012-03-01

This report presents 16 case studies of attacks planned or carried out against Israeli bus targets, along with statistical data on the number, frequency, and lethality of attacks against bus targets that have taken place in Israel since 1970 and duri...

Research Electrical Distribution Bus | Energy Systems Integration Facility

Science.gov Websites

| NREL Research Electrical Distribution Bus Research Electrical Distribution Bus The research electrical distribution bus (REDB) is the heart of the Energy Systems Integration Facility electrical system throughout the laboratories. Photo of a technician performing maintenance on the Research Electrical

Alternative Fuels Data Center

Science.gov Websites

School Bus Clean School Bus is a public-private partnership that focuses on reducing children's exposure to harmful diesel exhaust by limiting school bus idling, implementing pollution reduction technologies, improving route logistics, and switching to clean fuels. Clean School Bus is part of the U.S

Recommendations for yield-to-bus traffic control devices and bus pullout bays design characteristics : [research summary].

DOT National Transportation Integrated Search

2013-04-01

Bus pullout bays are being installed increasingly : on Floridas roads as a safety factor and so that : stopped buses do not impede traffic. In Florida, : state law requires car drivers to yield to buses : when a bus needs to reenter the roadway af...

49 CFR 571.220 - Standard No. 220; School bus rollover protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 220; School bus rollover protection... STANDARDS Federal Motor Vehicle Safety Standards § 571.220 Standard No. 220; School bus rollover protection. S1. Scope. This standard establishes performance requirements for school bus rollover protection. S2...

Design of a High Speed Data Capture Device for a Coherent Radar Application

DTIC Science & Technology

2006-11-01

of the RGASM is discussed, then the primary differences between coherent and non-coherent processing are compared. A basic digital receiver is then...IPP. 19 In-Phase Data Transfer Quadrature Data Transfer Label: Fuction : IQ-Sel Signifies whether data present on the bus is In-Phase or Quadrature...430S_IIZ _ l -.. t....!.... Label: Fuction : ADRS 16-bit address bus value DATA Actual 16-bit value of the data on the bus BUSEN* Bus enable READY* Bus

A series of small scientific satellite with flexible standard bus

NASA Astrophysics Data System (ADS)

Saito, Hirobumi; Sawai, Syujiro; Sakai, Shin-ichiro; Fukuda, Seisuke; Kitade, Kenji

2009-11-01

Japan Aerospace Exploration Agency has a plan to develop the small satellite standard bus for various scientific missions and disaster monitoring missions. The satellite bus is a class of 250-400 kg mass with three-axis control capability of 0.02∘ accuracy. The science missions include X-ray astronomy missions, planetary telescope missions, and magnetosphere atmosphere missions. In order to adapt the wide range of mission requirements, the satellite bus has to be provided with flexibility. The concepts of modularization, reusability, and product line are applied to the standard bus system. This paper describes the characteristics of the small satellite standard bus which will be firstly launched in 2011.

Combined Quarterly Technical Report Number 25. SATNET Development and Operation, Pluribus Satellite IMP Development, Remote Site Maintenance, Internet Operations and Maintenance, Mobile Access Terminal Network, TCP for the HP3000, TCP for VAX-UNIX.

DTIC Science & Technology

1982-05-01

the F-Bus. The two possible SuperSUE I Pollers, SSPE and SSPF, are on the E and F buses, respectively. P13 is the P13 Poller. A PSAT will have at... SSPE and SSPF are again the two possible SuperSUE Pollers. HPOL is an abbrevation for the HINPOL and HOUTPOL routines. -44- jReport No. 5003 Bolt...I IS I E-Bus,F-Bus I E-Bus Only I F-Bus only I s -- - - - - - - - - - - - - - - - - -- - - - - - P E-Bus ISMIE/ SSPE ISMIE/ SSPE ISMIF/SSPF IF-Bu3

A software bus for thread objects

NASA Technical Reports Server (NTRS)

Callahan, John R.; Li, Dehuai

1995-01-01

The authors have implemented a software bus for lightweight threads in an object-oriented programming environment that allows for rapid reconfiguration and reuse of thread objects in discrete-event simulation experiments. While previous research in object-oriented, parallel programming environments has focused on direct communication between threads, our lightweight software bus, called the MiniBus, provides a means to isolate threads from their contexts of execution by restricting communications between threads to message-passing via their local ports only. The software bus maintains a topology of connections between these ports. It routes, queues, and delivers messages according to this topology. This approach allows for rapid reconfiguration and reuse of thread objects in other systems without making changes to the specifications or source code. A layered approach that provides the needed transparency to developers is presented. Examples of using the MiniBus are given, and the value of bus architectures in building and conducting simulations of discrete-event systems is discussed.

MIL-STD-1553 dynamic bus controller/remote terminal hybrid set

NASA Astrophysics Data System (ADS)

Friedman, S. N.

This paper describes the performance, physical and electrical requirements of a Dual Redundant BUS Interface Unit (BIU) acting as a BUS Controller Interface Unit (BCIU) or Remote Terminal Unit (RTU) between a Motorola 68000 VME BUS and MIL-STD-1553B Multiplex Data Bus. A discussion of how the BIU Hybrid set is programmed, and operates as a BCIU or RTU, will be included. This paper will review Dynamic Bus Control and other Mode Code capabilities. The BIU Hybrid Set interfaces to a 68000 Microprocessor with a VME Bus using programmed I/O transfers. This special interface will be discussed along with the internal Dual Access Memory (4K x 16) used to support the data exchanges between the CPU and the BIU Hybrid Set. The hybrid set's physical size and power requirements will be covered. This includes the present Double Eurocard the BIU function is presently being offered on.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Lijuan; Gonder, Jeff; Burton, Evan

This study evaluates the costs and benefits associated with the use of a stationary-wireless- power-transfer-enabled plug-in hybrid electric bus and determines the cost effectiveness relative to a conventional bus and a hybrid electric bus. A sensitivity sweep was performed over many different battery sizes, charging power levels, and number/location of bus stop charging stations. The net present cost was calculated for each vehicle design and provided the basis for design evaluation. In all cases, given the assumed economic conditions, the conventional bus achieved the lowest net present cost while the optimal plug-in hybrid electric bus scenario beat out the hybridmore » electric comparison scenario. The study also performed parameter sensitivity analysis under favorable and high unfavorable market penetration assumptions. The analysis identifies fuel saving opportunities with plug-in hybrid electric bus scenarios at cumulative net present costs not too dissimilar from those for conventional buses.« less

The Quest for an OCO (Orbiting Carbon Observatory) Re-Flight

NASA Technical Reports Server (NTRS)

Basilio, Ralph R.; Livermore, Thomas R.; Shen, Y. Janet; Pollock, H. Randy

2010-01-01

The objective of the OCO (Orbiting Carbon Observatory) mission was to make the first space-based measurements of atmospheric carbon dioxide with the accuracy needed to quantify sources and sinks of this important greenhouse gas. Unfortunately, the observatory was lost as a result of a launch vehicle failure on 24 February 2009. The JPL (Jet Propulsion Laboratory) was directed to assess the options for the re-flight of the OCO instrument and recovery of the carbon-related measurement, and to understand and quantitatively assess the cost, schedule, and technical and programmatic risks of the identified options. The two most likely solutions were (1) a shared platform with the TIRS (Thermal Infrared Sensor) instrument and (2) a dedicated OSC (Orbital Sciences Corporation) LEOStar-2 spacecraft bus similar to that utilized for the original OCO mission. A joint OCO-TIRS mission study was commissioned and two specific options were examined. However, each presented technical challenges that would drive cost. It was determined that the best option was to rebuild the OCO observatory to the extent possible including another LEOStar-2 spacecraft bus. This lowest risk approach leverages the original OCO design and provides the shortest path to launch, which is targeted for no later than the February 2013 timeframe.

75 FR 5847 - Section 5309 Bus and Bus Facilities Livability Initiative and Urban Circulator Program Grants

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

... Livability Initiative and Urban Circulator Program Grants AGENCY: Federal Transit Administration (FTA), DOT. ACTION: Notice to Extend Application Deadline for the Bus and Bus Facilities and Urban Circulator..., Transportation Equity Act: A Legacy for Users (SAFETEA-LU), Public Law 109-59, August 10, 2005. The Urban...

The Role of the Coroner in School Bus Accident Prevention: Some Recommendations.

ERIC Educational Resources Information Center

Fox, Michael

1995-01-01

Following the deaths of two elementary school students in bus-related accidents in 1992, the Coroner of Quebec held extensive hearings investigating school bus safety and accident prevention. A subsequent report addressed responsibilities of government and school board officials to correct deficiencies in school bus services and provided…

School Bus Safety: What Can Our Schools Do to Protect Our Children?

ERIC Educational Resources Information Center

Dargan, Thomas J.; Silverstone, Adam H.

2014-01-01

School districts and school bus contractors are entrusted with the most important of all road users--our nation's children. In the wake of recent newsworthy accidents and attention grabbing headlines regarding unfit bus drivers, claims premised upon school bus accidents have become increasingly tangential and, in turn, personal injury attorneys…

49 CFR 383.123 - Requirements for a school bus endorsement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 5 2011-10-01 2011-10-01 false Requirements for a school bus endorsement. 383.123... Requirements for a school bus endorsement. (a) An applicant for the school bus endorsement must satisfy the... for school buses by State or Federal law or regulation. (ii) Emergency exits and procedures for safely...

Risk factors affecting fatal bus accident severity: Their impact on different types of bus drivers.

PubMed

Feng, Shumin; Li, Zhenning; Ci, Yusheng; Zhang, Guohui

2016-01-01

While the bus is generally considered to be a relatively safe means of transportation, the property losses and casualties caused by bus accidents, especially fatal ones, are far from negligible. The reasons for a driver to incur fatalities are different in each case, and it is essential to discover the underlying risk factors of bus fatality severity for different types of drivers in order to improve bus safety. The current study investigates the underlying risk factors of fatal bus accident severity to different types of drivers in the U.S. by estimating an ordered logistic model. Data for the analysis are retrieved from the Buses Involved in Fatal Accidents (BIFA) database from the USA for the years 2006-2010. Accidents are divided into three levels by counting their equivalent fatalities, and the drivers are classified into three clusters by the K-means cluster analysis. The analysis shows that some risk factors have the same impact on different types of drivers, they are: (a) season; (b) day of week; (c) time period; (d) number of vehicles involved; (e) land use; (f) manner of collision; (g) speed limit; (h) snow or ice surface condition; (i) school bus; (j) bus type and seating capacity; (k) driver's age; (l) driver's gender; (m) risky behaviors; and (n) restraint system. Results also show that some risk factors only have impact on the "young and elder drivers with history of traffic violations", they are: (a) section type; (b) number of lanes per direction; (c) roadway profile; (d) wet road surface; and (e) cyclist-bus accident. Notably, history of traffic violations has different impact on different types of bus drivers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Road safety issues for bus transport management.

PubMed

Cafiso, Salvatore; Di Graziano, Alessandro; Pappalardo, Giuseppina

2013-11-01

Because of the low percentage of crashes involving buses and the assumption that public transport improves road safety by reducing vehicular traffic, public interest in bus safety is not as great as that in the safety of other types of vehicles. It is possible that less attention is paid to the significance of crashes involving buses because the safety level of bus systems is considered to be adequate. The purpose of this study was to evaluate the knowledge and perceptions of bus managers with respect to safety issues and the potential effectiveness of various technologies in achieving higher safety standards. Bus managers were asked to give their opinions on safety issues related to drivers (training, skills, performance evaluation and behaviour), vehicles (maintenance and advanced devices) and roads (road and traffic safety issues) in response to a research survey. Kendall's algorithm was used to evaluate the level of concordance. The results showed that the majority of the proposed items were considered to have great potential for improving bus safety. The data indicated that in the experience of the participants, passenger unloading and pedestrians crossing near bus stops are the most dangerous actions with respect to vulnerable users. The final results of the investigation showed that start inhibition, automatic door opening, and the materials and internal architecture of buses were considered the items most strongly related to bus passenger safety. Brake assistance and vehicle monitoring systems were also considered to be very effective. With the exception of driver assistance systems for passenger and pedestrian safety, the perceptions of the importance of other driver assistance systems for vehicle monitoring and bus safety were not unanimous among the bus company managers who participated in this survey. The study results showed that the introduction of new technologies is perceived as an important factor in improving bus safety, but a better understanding of their actual effectiveness and related risk factor avoidance must be developed to permit their useful implementation in bus fleets. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Conceptual Approach for Optimising Bus Stop Spacing

NASA Astrophysics Data System (ADS)

Johar, Amita; Jain, S. S.; Garg, P. k.

2017-06-01

An efficient public transportation system is essential of any country. The growth, development and shape of the urban areas are mainly due to availability of good transportation (Shah et al. in Inst Town Plan India J 5(3):50-59, 1). In developing countries, like India, travel by local bus in a city is very common. The accidents, congestion, pollution and appropriate location of bus stops are the major problems arising in metropolitan cities. Among all the metropolitan cities in India, Delhi has highest percentage of growth of population and vehicles. Therefore, it is important to adopt efficient and effective ways to improve mobility in different metropolitan cities in order to overcome the problem and to reduce the number of private vehicles on the road. The primary objective of this paper is to present a methodology for developing a model for optimum bus stop spacing (OBSS). It describes the evaluation of existing urban bus route, data collection, development of model for optimizing urban bus route and application of model. In this work, the bus passenger generalized cost method is used to optimize the spacing between bus stops. For the development of model, a computer program is required to be written. The applicability of the model has been evaluated by taking the data of urban bus route of Delhi Transport Corporation (DTC) in Excel sheet in first phase. Later on, it is proposed to develop a programming in C++ language. The developed model is expected to be useful to transport planner for rational design of the spacing of bus stops to save travel time and to generalize operating cost. After analysis it is found that spacing between the bus stop comes out to be between 250 and 500 m. The Proposed Spacing of bus stops is done considering the points that they don't come nearer to metro/rail station, entry or exit of flyover and near traffic signal.

Parameters Identification for Motorcycle Simulator's Platform Characterization

NASA Astrophysics Data System (ADS)

Nehaoua, L.; Arioui, H.

2008-06-01

This paper presents the dynamics modeling and parameters identification of a motorcycle simulator's platform. This model begins with some suppositions which consider that the leg dynamics can be neglected with respect to the mobile platform one. The objectif is to synthesis a simplified control scheme, adapted to driving simulation application, minimising dealys and without loss of tracking performance. Electronic system of platform actuation is described. It's based on a CAN BUS communication which offers a large transmission robustness and error handling. Despite some disadvanteges, we adapted a control solution which overcome these inconvenients and preserve the quality of tracking trajectory. A bref description of the simulator's platform is given and results are shown and justified according to our specifications.

Design on the x-ray oral digital image display card

NASA Astrophysics Data System (ADS)

Wang, Liping; Gu, Guohua; Chen, Qian

2009-10-01

According to the main characteristics of X-ray imaging, the X-ray display card is successfully designed and debugged using the basic principle of correlated double sampling (CDS) and combined with embedded computer technology. CCD sensor drive circuit and the corresponding procedures have been designed. Filtering and sampling hold circuit have been designed. The data exchange with PC104 bus has been implemented. Using complex programmable logic device as a device to provide gating and timing logic, the functions which counting, reading CPU control instructions, corresponding exposure and controlling sample-and-hold have been completed. According to the image effect and noise analysis, the circuit components have been adjusted. And high-quality images have been obtained.

Characterizing the range of children's air pollutant exposure during school bus commutes.

PubMed

Sabin, Lisa D; Behrentz, Eduardo; Winer, Arthur M; Jeong, Seong; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

2005-09-01

Real-time and integrated measurements of gaseous and particulate pollutants were conducted inside five conventional diesel school buses, a diesel bus with a particulate trap, and a bus powered by compressed natural gas (CNG) to determine the range of children's exposures during school bus commutes and conditions leading to high exposures. Measurements were made during 24 morning and afternoon commutes on two Los Angeles Unified School District bus routes from South to West Los Angeles, with seven additional runs on a rural/suburban route, and three runs to test the effect of window position. For these commutes, the mean concentrations of diesel vehicle-related pollutants ranged from 0.9 to 19 microg/m(3) for black carbon, 23 to 400 ng/m(3) for particle-bound polycyclic aromatic hydrocarbon (PB-PAH), and 64 to 220 microg/m(3) for NO(2). Concentrations of benzene and formaldehyde ranged from 0.1 to 11 microg/m(3) and 0.3 to 5 microg/m(3), respectively. The highest real-time concentrations of black carbon, PB-PAH and NO(2) inside the buses were 52 microg/m(3), 2000 ng/m(3), and 370 microg/m(3), respectively. These pollutants were significantly higher inside conventional diesel buses compared to the CNG bus, although formaldehyde concentrations were higher inside the CNG bus. Mean black carbon, PB-PAH, benzene and formaldehyde concentrations were higher when the windows were closed, compared with partially open, in part, due to intrusion of the bus's own exhaust into the bus cabin, as demonstrated through the use of a tracer gas added to each bus's exhaust. These same pollutants tended to be higher on urban routes compared to the rural/suburban route, and substantially higher inside the bus cabins compared to ambient measurements. Mean concentrations of pollutants with substantial secondary formation, such as PM(2.5), showed smaller differences between open and closed window conditions and between bus routes. Type of bus, traffic congestion levels, and encounters with other diesel vehicles contributed to high exposure variability between runs.

Design and performance of the ALMA-J prototype antenna

NASA Astrophysics Data System (ADS)

Ukita, Nobuharu; Saito, Masao; Ezawa, Hajime; Ikenoue, Bungo; Ishizaki, Hideharu; Iwashita, Hiroyuki; Yamaguchi, Nobuyuki; Hayakawa, Takahiro

2004-10-01

The National Astronomical Observatory of Japan has constructed a prototype 12-m antenna of the Atacama Compact Array to evaluate its performance at the ALMA Test Facility in the NRAO VLA observatory in New Mexico, the United States. The antenna has a CFRP tube backup structure (BUS) with CFRP boards to support 205 machined Aluminum surface panels. Their accuracies were measured to be 5.9 m rms on average. A chemical treatment technique of the surface panels has successfully applied to scatter the solar radiation, which resulted in a subreflector temperature increase of about 25 degrees relative to ambient temperature during direct solar observations. Holography measurements and panel adjustments led to a final surface accuracy of 20 m rms, (weighted by 12dB edge taper), after three rounds of the panel adjustments. Based on a long term temperature monitoring of the BUS and thermal deformation FEM calculation, the BUS thermal deformation was estimated to be less than 3.1 m rms. We have employed gear drive mechanism both for a fast position switching capability and for smooth drive at low velocities. Servo errors measured with angle encoders were found to be less than 0.1 arcseconds rms at rotational velocities below 0.1 degrees s-1 and to increase to 0.7 arcseconds rms at the maximum speed of the 'on-the-fly' scan as a single dish, 0.5 deg s-1 induced by the irregularity of individual gear tooth profiles. Simultaneous measurements of the antenna motion with the angle encoders and seismic accelerometers mounted at the primary reflector mirror edges and at the subreflector showed the same amplitude and phase of oscillation, indicating that they are rigid, suggesting that it is possible to estimate where the antenna is actually pointing from the encoder readout. Continuous tracking measurements of Polaris during day and night have revealed a large pointing drift due to thermal distortion of the yoke structure. We have applied retrospective thermal corrections to tracking data for two hours, with a preliminary thermal deformation model of the yoke, and have found the tracking accuracy improved to be 0.1 - 0.3 arcseconds rms for a 15-munites period. The whole sky absolute pointing error under no wind and during night was measured to be 1.17 arcseconds rms. We need to make both an elaborated modeling of thermal deformation of the structure and systematic searches for significant correlation among pointing errors and metrology sensor outputs to achieve the stable tracking performance requested by ALMA.

Microbial air quality in mass transport buses and work-related illness among bus drivers of Bangkok Mass Transit Authority.

PubMed

Luksamijarulkul, Pipat; Sundhiyodhin, Viboonsri; Luksamijarulkul, Soavalug; Kaewboonchoo, Orawan

2004-06-01

The air quality in mass transport buses, especially air-conditioned buses may affect bus drivers who work full time. Bus numbers 16, 63, 67 and 166 of the Seventh Bus Zone of Bangkok Mass Transit Authority were randomly selected to investigate for microbial air quality. Nine air-conditioned buses and 2-4 open-air buses for each number of the bus (36 air-conditioned buses and 12 open-air buses) were included. Five points of in-bus air samples in each studied bus were collected by using the Millipore A ir Tester Totally, 180 and 60 air samples collected from air-conditioned buses and open-air buses were cultured for bacterial and fungal counts. The bus drivers who drove the studied buses were interviewed towards histories of work-related illness while working. The results revealed that the mean +/- SD of bacterial counts in the studied open-air buses ranged from 358.50 +/- 146.66 CFU/m3 to 506 +/- 137.62 CFU/m3; bus number 16 had the highest level. As well as the mean +/- SD of fungal counts which ranged from 93.33 +/- 44.83 CFU/m3 to 302 +/- 294.65 CFU/m3; bus number 166 had the highest level. Whereas, the mean +/- SD of bacterial counts in the studied air-conditioned buses ranged from 115.24 +/- 136.01 CFU/m3 to 244.69 +/- 234.85 CFU/m3; bus numbers 16 and 67 had the highest level. As well as the mean +/- SD of fungal counts which rangedfrom 18.84 +/- 39.42 CFU/m3 to 96.13 +/- 234.76 CFU/m3; bus number 166 had the highest level. When 180 and 60 studied air samples were analyzed in detail, it was found that 33.33% of the air samples from open-air buses and 6.11% of air samples from air-conditioned buses had a high level of bacterial counts (> 500 CFU/m3) while 6.67% of air samples from open-air buses and 2.78% of air samples from air-conditioned buses had a high level of fungal counts (> 500 CFU/m3). Data from the history of work-related illnesses among the studied bus drivers showed that 91.67% of open-air bus drivers and 57.28% of air-conditioned bus drivers had symptoms of work-related illnesses, p = 0.0185.

High-Speed Ring Bus

NASA Technical Reports Server (NTRS)

Wysocky, Terry; Kopf, Edward, Jr.; Katanyoutananti, Sunant; Steiner, Carl; Balian, Harry

2010-01-01

The high-speed ring bus at the Jet Propulsion Laboratory (JPL) allows for future growth trends in spacecraft seen with future scientific missions. This innovation constitutes an enhancement of the 1393 bus as documented in the Institute of Electrical and Electronics Engineers (IEEE) 1393-1999 standard for a spaceborne fiber-optic data bus. It allows for high-bandwidth and time synchronization of all nodes on the ring. The JPL ring bus allows for interconnection of active units with autonomous operation and increased fault handling at high bandwidths. It minimizes the flight software interface with an intelligent physical layer design that has few states to manage as well as simplified testability. The design will soon be documented in the AS-1393 standard (Serial Hi-Rel Ring Network for Aerospace Applications). The framework is designed for "Class A" spacecraft operation and provides redundant data paths. It is based on "fault containment regions" and "redundant functional regions (RFR)" and has a method for allocating cables that completely supports the redundancy in spacecraft design, allowing for a complete RFR to fail. This design reduces the mass of the bus by incorporating both the Control Unit and the Data Unit in the same hardware. The standard uses ATM (asynchronous transfer mode) packets, standardized by ITU-T, ANSI, ETSI, and the ATM Forum. The IEEE-1393 standard uses the UNI form of the packet and provides no protection for the data portion of the cell. The JPL design adds optional formatting to this data portion. This design extends fault protection beyond that of the interconnect. This includes adding protection to the data portion that is contained within the Bus Interface Units (BIUs) and by adding to the signal interface between the Data Host and the JPL 1393 Ring Bus. Data transfer on the ring bus does not involve a master or initiator. Following bus protocol, any BIU may transmit data on the ring whenever it has data received from its host. There is no centralized arbitration or bus granting. The JPL design provides for autonomous synchronization of the nodes on the ring bus. An address-synchronous latency adjust buffer (LAB) has been designed that cannot get out of synchronization and needs no external input. Also, a priority-driven cable selection behavior has been programmed into each unit on the ring bus. This makes the bus able to connect itself up, according to a maximum redundancy priority system, without the need for computer intervention at startup. Switching around a failed or switched-off unit is also autonomous. The JPL bus provides a map of all the active units for the host computer to read and use for fault management. With regard to timing, this enhanced bus recognizes coordinated timing on a spacecraft as critical and addresses this with a single source of absolute and relative time, which is broadcast to all units on the bus with synchronization maintained to the tens of nanoseconds. Each BIU consists of up to five programmable triggers, which may be programmed for synchronization of events within the spacecraft of instrument. All JPL-formatted data transmitted on the ring bus are automatically time-stamped.

School Bus Rider Safety Education Modules for Use with Drills on School Buses.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Div. of Physical Education, Fitness, Health, Nutrition and Safety Services.

Developed for teachers and members of the pupil transportation staff who conduct school bus drills, these 10 lesson outlines are intended for classroom instruction on school bus safety. Lessons may be adapted to fit the grade level, intelligence, and special needs of students. Topics covered are: preparing to ride the bus, boarding and proceeding…

Increasing security in inter-chip communication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, Nathan J.; Hamlet, Jason; Bauer, Todd

An apparatus for increasing security in inter-chip communication includes a sending control module, a communication bus, and a receiving control module. The communication bus is coupled between the sending control module and the receiving control module. The sending control module operates to send data on the communication bus, disable the communication bus when threats are detected, or both.

Bus-Programmable Slave Card

NASA Technical Reports Server (NTRS)

Hall, William A.

1990-01-01

Slave microprocessors in multimicroprocessor computing system contains modified circuit cards programmed via bus connecting master processor with slave microprocessors. Enables interactive, microprocessor-based, single-loop control. Confers ability to load and run program from master/slave bus, without need for microprocessor development station. Tristate buffers latch all data and information on status. Slave central processing unit never connected directly to bus.

School Bus Accidents and Driver Age.

ERIC Educational Resources Information Center

McMichael, Judith

The study examines the rates and types of school bus accidents according to the age of the school bus driver. Accident rates in North Carolina for the school year 1971-72 were analyzed using three sources of data: accident reports, driver and mileage data, and questionnaires administered to a sample of school bus drivers. Data were obtained on…

Increasing security in inter-chip communication

DOEpatents

Edwards, Nathan J; Hamlet, Jason; Bauer, Todd; Helinski, Ryan

2014-10-28

An apparatus for increasing security in inter-chip communication includes a sending control module, a communication bus, and a receiving control module. The communication bus is coupled between the sending control module and the receiving control module. The sending control module operates to send data on the communication bus, disable the communication bus when threats are detected, or both.

49 CFR 571.222 - Standard No. 222; School bus passenger seating and crash protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 222; School bus passenger seating and... VEHICLE SAFETY STANDARDS Federal Motor Vehicle Safety Standards § 571.222 Standard No. 222; School bus... requirements for school bus passenger seating and restraining barriers. S2. Purpose. The purpose of this...

The SMART MIL-STD-1553 bus adapter hardware manual

NASA Technical Reports Server (NTRS)

Ton, T. T.

1981-01-01

The SMART Multiplexer Interface Adapter, (SMIA) a complete system interface for message structure of the MIL-STD-1553, is described. It provides buffering and storage for transmitted and received data and handles all the necessary handshaking to interface between parallel 8-bit data bus and a MIL-STD serial bit stream. The bus adapter is configured as either a bus controller of a remote terminal interface. It is coupled directly to the multiplex bus, or stub coupled through an additional isolation transformer located at the connection point. Fault isolation resistors provide short circuit protection.

Users' demographic profile and quality attributes of bus services: The perspectives of users, operators and local authorities

NASA Astrophysics Data System (ADS)

Noh, Nur'Amirah Mhd.; Hamid, Ahmad Hilmy Abd

2017-10-01

Bus services that can help meet almost every bus user's needs are the goals of bus operators. Despite such an idealistic view, the operators themselves, users and even the local authorities have been found to hold different views about the quality of service that the bus should deliver. As the users i.e., customers are considered as important stakeholders, understanding their characteristics, profile and pattern is very crucial. To this end, the present study has attempted to gauge the perspectives of all the above-mentioned stakeholders. For the users, a customer satisfaction survey was employed to look into the relative influence of service attributes. In addition, surveys were also administered to bus operators and local authorities to study their perspectives in relation to this matter. 450 randomly selected respondents were surveyed. Identification of the service level was analyzed through the Likert scale whereas the perspectives of the operators and authorities were dealt with through mean value Analysis. Specifically, this study aims to identify the crucial attributes in determining the quality of the bus services. Findings of the study indicated that different attributes were selected by users, operators and authorities, which clearly enlightened the variations of the important attributes in determining the level of bus service quality. In its attempt to compare the service level attributes from three perspectives, this study has helped advance better improvement and strategies for the urban public bus operators and planners, in addition to the authorities in delivering user-friendly bus services by taking into account the local context, user profile and demographic characteristics.

Modeling level-of-safety for bus stops in China.

PubMed

Ye, Zhirui; Wang, Chao; Yu, Yongbo; Shi, Xiaomeng; Wang, Wei

2016-08-17

Safety performance at bus stops is generally evaluated by using historical traffic crash data or traffic conflict data. However, in China, it is quite difficult to obtain such data mainly due to the lack of traffic data management and organizational issues. In light of this, the primary objective of this study is to develop a quantitative approach to evaluate bus stop safety performance. The concept of level-of-safety for bus stops is introduced and corresponding models are proposed to quantify safety levels, which consider conflict points, traffic factors, geometric characteristics, traffic signs and markings, pavement conditions, and lighting conditions. Principal component analysis and k-means clustering methods were used to model and quantify safety levels for bus stops. A case study was conducted to show the applicability of the proposed model with data collected from 46 samples for the 7 most common types of bus stops in China, using 32 of the samples for modeling and 14 samples for illustration. Based on the case study, 6 levels of safety for bus stops were defined. Finally, a linear regression analysis between safety levels and the number of traffic conflicts showed that they had a strong relationship (R(2) value of 0.908). The results indicated that the method was well validated and could be practically used for the analysis and evaluation of bus stop safety in China. The proposed model was relatively easy to implement without the requirement of traffic crash data and/or traffic conflict data. In addition, with the proposed method, it was feasible to evaluate countermeasures to improve bus stop safety (e.g., exclusive bus lanes).

An improved fault-tolerant control scheme for PWM inverter-fed induction motor-based EVs.

PubMed

Tabbache, Bekheïra; Benbouzid, Mohamed; Kheloui, Abdelaziz; Bourgeot, Jean-Matthieu; Mamoune, Abdeslam

2013-11-01

This paper proposes an improved fault-tolerant control scheme for PWM inverter-fed induction motor-based electric vehicles. The proposed strategy deals with power switch (IGBTs) failures mitigation within a reconfigurable induction motor control. To increase the vehicle powertrain reliability regarding IGBT open-circuit failures, 4-wire and 4-leg PWM inverter topologies are investigated and their performances discussed in a vehicle context. The proposed fault-tolerant topologies require only minimum hardware modifications to the conventional off-the-shelf six-switch three-phase drive, mitigating the IGBTs failures by specific inverter control. Indeed, the two topologies exploit the induction motor neutral accessibility for fault-tolerant purposes. The 4-wire topology uses then classical hysteresis controllers to account for the IGBT failures. The 4-leg topology, meanwhile, uses a specific 3D space vector PWM to handle vehicle requirements in terms of size (DC bus capacitors) and cost (IGBTs number). Experiments on an induction motor drive and simulations on an electric vehicle are carried-out using a European urban driving cycle to show that the proposed fault-tolerant control approach is effective and provides a simple configuration with high performance in terms of speed and torque responses. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

A decentralized software bus based on IP multicas ting

NASA Technical Reports Server (NTRS)

Callahan, John R.; Montgomery, Todd

1995-01-01

We describe decentralized reconfigurable implementation of a conference management system based on the low-level Internet Protocol (IP) multicasting protocol. IP multicasting allows low-cost, world-wide, two-way transmission of data between large numbers of conferencing participants through the Multicasting Backbone (MBone). Each conference is structured as a software bus -- a messaging system that provides a run-time interconnection model that acts as a separate agent (i.e., the bus) for routing, queuing, and delivering messages between distributed programs. Unlike the client-server interconnection model, the software bus model provides a level of indirection that enhances the flexibility and reconfigurability of a distributed system. Current software bus implementations like POLYLITH, however, rely on a centralized bus process and point-to-point protocols (i.e., TCP/IP) to route, queue, and deliver messages. We implement a software bus called the MULTIBUS that relies on a separate process only for routing and uses a reliable IP multicasting protocol for delivery of messages. The use of multicasting means that interconnections are independent of IP machine addresses. This approach allows reconfiguration of bus participants during system execution without notifying other participants of new IP addresses. The use of IP multicasting also permits an economy of scale in the number of participants. We describe the MULITIBUS protocol elements and show how our implementation performs better than centralized bus implementations.

Preliminary Investigation of Workload on Intrastate Bus Traffic Controllers

NASA Astrophysics Data System (ADS)

Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

2016-11-01

The daily routine of bus traffic controller which involves high mental processes would have a direct impact on the level of workload. To date, the level of workload on the bus traffic controllers in Malaysia is relatively unknown. Excessive workload on bus traffic controllers would affect the control and efficiency of the system. This paper served to study the workload on bus traffic controllers and justify the needs to conduct further detailed research on this field. The objectives of this research are to identify the level of workload on the intrastate bus traffic controllers. Based on the results, recommendations will be proposed for improvements and future studies. The level of workload for the bus traffic controllers is quantified using questionnaire adapted from NASA TLX. Interview sessions were conducted for validation of workload. Sixteen respondents were involved and it was found that the average level of workload based on NASA TLX was 6.91. It was found that workload is not affected by gender and marital status. This study also showed that the level of workload and working experience of bus traffic controllers has a strong positive linear relationship. This study would serve as a guidance and reference related to this field. Since this study is a preliminary investigation, further detailed studies could be conducted to obtain a better comprehension regarding the bus traffic controllers.

Activities of four bus terminals of Semarang City gateway and the related GHG emission

NASA Astrophysics Data System (ADS)

Huboyo, H. S.; Wardhana, I. W.; Sutrisno, E.; Wangi, L. S.; Lina, R. A.

2018-01-01

The activities of the bus terminal, including loading-unloading passengers, bus idling, and bus movements at the terminal, will emit GHG’s emission. This research analyzes GHG emission from four terminals, i.e., Mangkang, Terboyo, Penggaron, and Sukun in Semarang City. The emission was estimated by observing detail activities of public transport means, especially for moving and idling time. The emission was calculated by Tier 2 method based on the vehicle type as well as fuel consumption. The highest CO2e during vehicle movements at Sukun area was contributed by large bus about 2.08 tons/year, while at Terboyo terminal was contributed by medium bus about 347.97 tons/year. At Mangkang terminals, the highest emission for vehicle movements was attributed by medium bus as well of about 53.18 tons/year. At last, Penggaron terminal’s highest GHG emission was attributed by BRT about 26.47 tons/year. During idling time, the highest contributor to CO2e was the large bus at the three terminals, i.e., Sukun of 43.53 tons/year, Terboyo of 196.56 tons/year, and Mangkang of 84.26 tons/year, while at Penggaron, BRT dominated with CO2e of 26.47 tons/year. The management of public transport in terminals is crucial to mitigate the emission related to bus terminals activities.

Get off the bus: sound strategy for injury prevention during a tornado?

PubMed

Comstock, R Dawn; Mallonee, Sue

2005-01-01

On 08 May 2003, a tornado categorized as an F-3 on the Fujita Tornado Scale (the "F Scale") struck an Oklahoma City, Oklahoma commuter bus carrying 24 passengers. The driver evacuated several passengers before the tornado struck. The tornado rolled the bus, and pelted it with debris. A case-series investigation of tornado-related injuries was conducted among passengers who were evacuated to a ditch and those who remained on the bus when the tornado struck. Nineteen of 24 passengers sought care for injuries at hospital emergency departments (injury rate = 79.2%). While a greater number of passengers who were outside the bus when the tornado struck (11) sought care for injuries than did those who remained on the bus (8); passengers outside of the bus suffered fewer injuries than did those who remained on the bus (median number of injuries 3 versus 4), and their injuries were less severe (median injury severity score (ISS) 1 versus 4). For persons caught in motor vehicles during tornado events, this study supports currently accepted recommendations to immediately evacuate and lie in a low-lying area away from motor vehicles if other shelter is unavailable. However, generalizing the experience of bus passengers to automobile drivers might be inappropriate because buses lack the safety features that might protect automobile drivers from tornado-related injuries.

A Safe Ride to School; A Safe Ride Home.

ERIC Educational Resources Information Center

Illinois State Board of Education, Springfield.

Text and illustrations are used to teach safe school bus riding practices. The guide begins with instructions to parents or guardians to set a good example of safe behavior, and to help children learn safety rules and be on time. Instructions to children concern obeying the bus driver, boarding the bus, riding the bus, crossing the road, and using…

Computer-Based Video Instruction to Teach Students with Intellectual Disabilities to Use Public Bus Transportation

ERIC Educational Resources Information Center

Mechling, Linda; O'Brien, Eileen

2010-01-01

This study investigated the effectiveness of computer-based video instruction (CBVI) to teach three young adults with moderate intellectual disabilities to push a "request to stop bus signal" and exit a city bus in response to target landmarks. A multiple probe design across three students and one bus route was used to evaluate effectiveness of…

Perceptions of Heat Risk to Health: A Qualitative Study of Professional Bus Drivers and Their Managers in Jinan, China

PubMed Central

Zhou, Lin; Xin, Zheng; Bai, Li; Wan, Fangjun; Wang, Yongming; Sang, Shaowei; Liu, Shouqin; Zhang, Ji; Liu, Qiyong

2014-01-01

Summer extreme heat threatens the health of individuals, especially persons who are involved in outdoor activities. Ensuring the normal function of a city, bus drivers are among those who participate in outdoor physical activities and are exposed to excessive heat in hot summer weather. This qualitative study was performed to explore professional bus drivers’ in-depth views of extreme heat risks to their health, and ultimately develop targeted advice and policy interventions for city bus drivers. An interview-based study was performed among professional bus drivers in Jinan, China, including four focus groups with professional bus drivers (n = 37) and three interviews with their managers (n = 14). Five central themes or categories from the bus driver interviews were found: concerns about summer heat; health effects related to extreme heat; adaptive measures; barriers in implementing these adaptive measures; and suggested interventions. The beneficial role of cooling facilities (particularly air-conditioning) during extreme heat are addressed. The barriers not only impede the implementation of behavioral adaptive measures but also enhance the negative attitudes of bus drivers towards their effectiveness. The responsibilities of managers in promoting preventive actions are addressed. PMID:24477213

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, L.; Chandler, K.

2013-01-01

SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and helpmore » determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.« less

Fault tolerant data management system

NASA Technical Reports Server (NTRS)

Gustin, W. M.; Smither, M. A.

1972-01-01

Described in detail are: (1) results obtained in modifying the onboard data management system software to a multiprocessor fault tolerant system; (2) a functional description of the prototype buffer I/O units; (3) description of modification to the ACADC and stimuli generating unit of the DTS; and (4) summaries and conclusions on techniques implemented in the rack and prototype buffers. Also documented is the work done in investigating techniques of high speed (5 Mbps) digital data transmission in the data bus environment. The application considered is a multiport data bus operating with the following constraints: no preferred stations; random bus access by all stations; all stations equally likely to source or sink data; no limit to the number of stations along the bus; no branching of the bus; and no restriction on station placement along the bus.

Genetic Algorithm for Multiple Bus Line Coordination on Urban Arterial

PubMed Central

Yang, Zhen; Wang, Wei; Chen, Shuyan; Ding, Haoyang; Li, Xiaowei

2015-01-01

Bus travel time on road section is defined and analyzed with the effect of multiple bus lines. An analytical model is formulated to calculate the total red time a bus encounters when travelling along the arterial. Genetic algorithm is used to optimize the offset scheme of traffic signals to minimize the total red time that all bus lines encounter in two directions of the arterial. The model and algorithm are applied to the major part of Zhongshan North Street in the city of Nanjing. The results show that the methods in this paper can reduce total red time of all the bus lines by 31.9% on the object arterial and thus improve the traffic efficiency of the whole arterial and promote public transport priority. PMID:25663837

Content-addressable memory based enforcement of configurable policies

DOEpatents

Berg, Michael J

2014-05-06

A monitoring device for monitoring transactions on a bus includes content-addressable memory ("CAM") and a response policy unit. The CAM includes an input coupled to receive a bus transaction tag based on bus traffic on the bus. The CAM stores data tags associated with rules of a security policy to compare the bus transaction tag to the data tags. The CAM generates an output signal indicating whether one or more matches occurred. The response policy unit is coupled to the CAM to receive the output signal from the CAM and to execute a policy action in response to the output signal.

Modeling transit bus fuel consumption on the basis of cycle properties.

PubMed

Delgado, Oscar F; Clark, Nigel N; Thompson, Gregory J

2011-04-01

A method exists to predict heavy-duty vehicle fuel economy and emissions over an "unseen" cycle or during unseen on-road activity on the basis of fuel consumption and emissions data from measured chassis dynamometer test cycles and properties (statistical parameters) of those cycles. No regression is required for the method, which relies solely on the linear association of vehicle performance with cycle properties. This method has been advanced and examined using previously published heavy-duty truck data gathered using the West Virginia University heavy-duty chassis dynamometer with the trucks exercised over limited test cycles. In this study, data were available from a Washington Metropolitan Area Transit Authority emission testing program conducted in 2006. Chassis dynamometer data from two conventional diesel buses, two compressed natural gas buses, and one hybrid diesel bus were evaluated using an expanded driving cycle set of 16 or 17 different driving cycles. Cycle properties and vehicle fuel consumption measurements from three baseline cycles were selected to generate a linear model and then to predict unseen fuel consumption over the remaining 13 or 14 cycles. Average velocity, average positive acceleration, and number of stops per distance were found to be the desired cycle properties for use in the model. The methodology allowed for the prediction of fuel consumption with an average error of 8.5% from vehicles operating on a diverse set of chassis dynamometer cycles on the basis of relatively few experimental measurements. It was found that the data used for prediction should be acquired from a set that must include an idle cycle along with a relatively slow transient cycle and a relatively high speed cycle. The method was also applied to oxides of nitrogen prediction and was found to have less predictive capability than for fuel consumption with an average error of 20.4%.

Hydrogen powered bus

ScienceCinema

Glass, Bob; Mathis, Mike; Cochran, Ron; Garback, John

2018-06-08

Take a ride on a new type of bus, fueled by hydrogen. These hydrogen taxis are part of a Department of Energy-funded deployment of hydrogen powered vehicles and fueling infrastructure at nine federal facilities across the country to demonstrate this market-ready advanced technology. Produced and leased by Ford Motor Company , they consist of one 12- passenger bus and one nine-passenger bus. More information at: http://go.usa.gov/Tgr

Ten bar probe technical summary. [feasibility of outer planet common atmospheric probe

NASA Technical Reports Server (NTRS)

Ellis, T. R.

1974-01-01

The feasibility of an outer planet common atmospheric probe is studied with emphasis on entry heating rates and improved ephemeris. It is concluded that a common probe design is possible except for Jupiter; the basic technology exists except for Jupiter heat shielding. A Mariner class bus provides for better bus science and probe bus communications than a Pioneer class bus.

Multi-access fiber optic data bus using FDM/FSK

NASA Technical Reports Server (NTRS)

Zanger, H.

1984-01-01

The major thrust was to develop a T coupler with very low (0.1 0.2dB) in-line loss. This is essential to any multiaccess bus structure where the word multi implies fifteen or more nodes on the bus, and it is tacitly assumed to be a passive bus. (Reliability considerations tend to exclude the use of active nodes - repeater nodes.)

TMS communications hardware. Volume 2: Bus interface unit

NASA Technical Reports Server (NTRS)

Brown, J. S.; Hopkins, G. T.

1979-01-01

A prototype coaxial cable bus communication system used in the Trend Monitoring System to interconnect intelligent graphics terminals to a host minicomputer is described. The terminals and host are connected to the bus through a microprocessor-based RF modem termed a Bus Interface Unit (BIU). The BIU hardware and the Carrier Sense Multiple Access Listen-While-Talk protocol used on the network are described.

Behavior Modification of Aggressive Behavior on a Nursery School Bus: A Case Study.1

ERIC Educational Resources Information Center

Whitehurst, Carol; Miller, Edward

1973-01-01

A case study is presented in which aggressive behavior of two pre-school boys on a nursery school bus was modified by the introduction of a negative punishment contingency in which the Ss were told they would be detained on the bus until the second time the bus passed their house (delay of reinforcement) if abusive behavior occurred. (Author)

The ins and outs of terrorist bus explosions: injury profiles of on-board explosions versus explosions occurring adjacent to a bus.

PubMed

Golan, Ron; Soffer, Dror; Givon, Adi; Peleg, Kobi

2014-01-01

Terrorist explosions occurring in varying settings have been shown to lead to significantly different injury patterns among the victims, with more severe injuries generally arising in confined space attacks. Increasing numbers of terrorist attacks have been targeted at civilian buses, yet most studies focus on events in which the bomb was detonated within the bus. This study focuses on the injury patterns and hospital utilisation among casualties from explosive terrorist bus attacks with the bomb detonated either within a bus or adjacent to a bus. All patients hospitalised at six level I trauma centres and four large regional trauma centres following terrorist explosions that occurred in and adjacent to buses in Israel between November 2000 and August 2004 were reviewed. Injury severity scores (ISS) were used to assess severity. Hospital utilisation data included length of hospital stay, surgical procedures performed, and intensive care unit (ICU) admission. The study included 262 victims of 22 terrorist attacks targeted at civilian bus passengers and drivers; 171 victims were injured by an explosion within a bus (IB), and 91 were injured by an explosion adjacent to a bus (AB). Significant differences were noted between the groups, with the IB population having higher ISS scores, more primary blast injury, more urgent surgical procedures performed, and greater ICU utilisation. Both groups had percentages of nearly 20% for burn injury, had high percentages of injuries to the head/neck, and high percentages of surgical wound and burn care. Explosive terrorist attacks detonated within a bus generate more severe injuries among the casualties and require more urgent surgical and intensive level care than attacks occurring adjacent to a bus. The comparison and description of the outcomes to these terrorist attacks should aid in the preparation and response to such devastating events. Copyright © 2013 Elsevier Ltd. All rights reserved.

The Bus Stops Here.

ERIC Educational Resources Information Center

Milshtein, Amy

1999-01-01

Explores some of the factors to consider before school planners decide to buy new school buses. Provides a checklist to help build and maintain a bus fleet. Concludes by addressing bus safety and advertising. (GR)

A new assessment method of outdoor tobacco smoke (OTS) exposure

NASA Astrophysics Data System (ADS)

Cho, Hyeri; Lee, Kiyoung

2014-04-01

Outdoor tobacco smoke (OTS) is concerned due to potential health effects. An assessment method of OTS exposure is needed to determine effects of OTS and validate outdoor smoking policies. The objective of this study was to develop a new method to assess OTS exposure. This study was conducted at 100 bus stops including 50 centerline bus stops and 50 roadside bus stops in Seoul, Korea. Using real-time aerosol monitor, PM2.5 was measured for 30 min at each bus stop in two seasons. ‘Peak analysis' method was developed to assess short term PM2.5 exposure by OTS. The 30-min average PM2.5 exposure at each bus stop was associated with season and bus stop location but not smoking activity. The PM2.5 peak occurrence rate by the peak analysis method was significantly associated with season, bus stop location, observed smoking occurrence, and the number of buses servicing a route. The PM2.5 peak concentration was significantly associated with season, smoking occurrence, and the number of buses servicing a route. When a smoker was standing still at the bus stop, magnitude of peak concentrations were significantly higher than when the smoker walking-through the bus stop. People were exposed to high short-term PM2.5 peak levels at bus stops, and the magnitude of peak concentrations were highest when a smoker was located close to the monitor. The magnitude of peak concentration was a good indicator helped distinguish nearby OTS exposure. Further research using ‘peak analysis' is needed to measure smoking-related exposure to PM2.5 in other outdoor locations.

Bus 54 -- Where are you? A school bus intelligent information system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Truett, L.F.; Moore, S.; Tonn, B.

1998-07-01

Although major accidents involving school buses are rare (only about 0.3% of all fatal crashes since 1986 are classified as school-bus-related), even minor accidents and breakdowns cause a great deal of parental anxiety. The objective of this research is to design an efficient, cost-effective, accurate, and secure system that will track individual school buses and communicate appropriate information to the school system`s central administration unit, to the school transportation administrator, and to parents of children on the bus. The greatest benefit of the proposed information system is that parents and officials can always know the location and condition (these conditionsmore » would vary depending on the needs of a particular school system) of the school buses. In case of an accident or mechanical problem, when emergency crews are needed, they can be dispatched almost immediately with a good understanding of the problem and the exact location of the bus. In addition to being able to track the bus while the child is on board, parents will be able to determine the location of their child`s bus prior to its arrival in the morning in order to prevent the child from needing to wait outside in inclement weather. The information available to parents can also be expanded to include maps of limited routes (e.g., snow routes). Basically, the Bus 54 concept consists of a bus component and a central data processing unit. Each bus will be outfitted with a global positioning satellite (GPS) device, a wireless communication device, and wireless data communication service. The central data processing unit will receive and process information from the buses and provide information access to parents and officials via an Internet link.« less

Landscape heritage objects' effect on driving: a combined driving simulator and questionnaire study.

PubMed

Antonson, Hans; Ahlström, Christer; Mårdh, Selina; Blomqvist, Göran; Wiklund, Mats

2014-01-01

According to the literature, landscape (panoramas, heritage objects e.g. landmarks) affects people in various ways. Data are primarily developed by asking people (interviews, photo sessions, focus groups) about their preferences, but to a lesser degree by measuring how the body reacts to such objects. Personal experience while driving a car through a landscape is even more rare. In this paper we study how different types of objects in the landscape affect drivers during their drive. A high-fidelity moving-base driving simulator was used to measure choice of speed and lateral position in combination with stress (heart rate measure) and eye tracking. The data were supplemented with questionnaires. Eighteen test drivers (8 men and 10 women) with a mean age of 37 were recruited. The test drivers were exposed to different new and old types of landscape objects such as 19th century church, wind turbine, 17th century milestone and bus stop, placed at different distances from the road driven. The findings are in some respect contradictory, but it was concluded that that 33% of the test drivers felt stressed during the drive. All test drivers said that they had felt calm at times during the drive but the reason for this was only to a minor degree connected with old and modern objects. The open landscape was experienced as conducive to acceleration. Most objects were, to a small degree, experienced (subjective data) as having a speed-reducing effect, much in line with the simulator data (objective data). Objects close to the road affected the drivers' choice of' lateral position. No significant differences could be observed concerning the test drivers' gaze between old or modern objects, but a significant difference was observed between the test drivers' gaze between road stretches with faraway objects and stretches without objects. No meaningful, significant differences were found for the drivers' stress levels as measured by heart rate. Copyright © 2013 Elsevier Ltd. All rights reserved.

Listing of New Bus Technology Applications

DOT National Transportation Integrated Search

1983-12-01

The New Bus Equipment Introduction program is designed to demonstrate innovative features on transit buses and encourage the adoption of innovative features that enhance productivity. New bus demonstrations and purchases have been catalogued for the ...

Method and systems for a radiation tolerant bus interface circuit

NASA Technical Reports Server (NTRS)

Kinstler, Gary A. (Inventor)

2007-01-01

A bus management tool that allows communication to be maintained between a group of nodes operatively connected on two busses in the presence of radiation by transmitting periodically a first message from one to another of the nodes on one of the busses, determining whether the first message was received by the other of the nodes on the first bus, and when it is determined that the first message was not received by the other of the nodes, transmitting a recovery command to the other of the nodes on a second of the of busses. Methods, systems, and articles of manufacture consistent with the present invention also provide for a bus recovery tool on the other node that re-initializes a bus interface circuit operatively connecting the other node to the first bus in response to the recovery command.

Scheduled Peripheral Component Interconnect Arbiter

NASA Technical Reports Server (NTRS)

Nixon, Scott Alan (Inventor)

2015-01-01

Systems and methods are described for arbitrating access of a communication bus. In one embodiment, a method includes performing steps on one or more processors. The steps include: receiving an access request from a device of the communication bus; evaluating a bus schedule to determine an importance of the device based on the access request; and selectively granting access of the communication bus to the device based on the importance of the device.

A study of multiplex data bus techniques for the space shuttle

NASA Technical Reports Server (NTRS)

Kearney, R. J.; Kalange, M. A.

1972-01-01

A comprehensive technology base for the design of a multiplexed data bus subsystem is provided. Extensive analyses, both analytical and empirical, were performed. Subjects covered are classified under the following headings: requirements identification and analysis; transmission media studies; signal design and detection studies; synchronization, timing, and control studies; user-subsystem interface studies; operational reliability analyses; design of candidate data bus configurations; and evaluation of candidate data bus designs.

Countermeasures for Developing New Energy Bus Standards in China

NASA Astrophysics Data System (ADS)

Shi, Xin

2018-01-01

With the rapid development of new energy vehicle technology, new energy bus has become more and more popular in China, and the relevant standards and policy are urgently needed to guide the market. According to the assessment of the development situation on new energy vehicle technology and new energy bus, combing with traffic policy guidance and the development trend of new energy vehicles, this paper aims to put forward the countermeasures of the new energy bus standard in China, including standard system, key standards and relevant recommendations. Research result is expected to provide decision support for the wide application of new energy bus in China.

Annoyance evaluation and the effect of noise on the health of bus drivers.

PubMed

Bruno, Portela S; Marcos, Queiroga R; Amanda, Constantini; Paulo, Zannin H T

2013-01-01

In the present study, we evaluated annoyance and the effects of noise on the health of bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality, occurrence of tinnitus, headache, irritation, and annoyance from bus engine, traffic, and passengers. Data of age and working time of bus drivers also were obtained. For noise exposure, LA eq was evaluated in 80 buses. Statistical analysis consisted of mean, standard deviation, minimum, and maximum, Kruskal-Wallis test with post-hoc Dunn, one-way ANOVA with post-hoc Tukey and Spearman's correlation coefficient. Results indicate three groups of bus drivers (not annoyed: (N.A.), a little annoyed (L.A.) and highly annoyed (H.A.)). The group H.A. was younger and with less working time in relation to others, with a significant difference only for age. Regarding sleep quality, there was no significant difference. For results on the occurrence of tinnitus, headache and irritation after work, group H.A. had significantly higher means. Result of annoyance to the bus engine was significantly higher in H.A. than in L.A. and N.A. Annoyance to traffic and passengers, no significant differences were found, but the highest results were found for L.A., followed by H.A. and N.A. Equivalent sound pressure level in buses was above of the limit for occupational comfort. It was concluded that bus drivers has considerable level of noise annoyance and some health effects are perceived. The noise is a factor discomfort ergonomic that may cause effects on health of bus drivers. This study aims to evaluate annoyance and the effects of noise on the health of bus drivers. Cross-sectional study with buses and bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality, occurrence of tinnitus, headache, irritation and annoyance from bus engine, traffic, and passengers. Data of age and working time of bus drivers also were obtained. For noise exposure, LA eq was evaluated in 80 buses. Statistical analysis consisted of mean, standard deviation, minimum and maximum, Kruskal-Wallis test with post-hoc Dunn, one-way ANOVA with post-hoc Tukey and Spearman's correlation coefficient. Results indicate three groups of bus drivers (N.A., a L.A. and H.A.). The group H.A. was younger and with less working time in relation to others, with a significant difference only for age. Regarding sleep quality, there was no significant difference. For results on the occurrence of tinnitus, headache and irritation after work, group H.A. had significantly higher means. Result of annoyance to the bus engine was significantly higher in H.A. than in L.A. and N.A. Annoyance to traffic and passengers, no significant differences were found, but the highest results were found for L.A., followed by H.A. and N.A. Equivalent sound pressure level in buses was above of the limit for occupational comfort. It was concluded that bus drivers has considerable level of noise annoyance and some health effects are perceived.

214. RUSTIC BUS SHELTER, GUARDRAILS AND LAMP POST BELLE HAVEN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

214. RUSTIC BUS SHELTER, GUARDRAILS AND LAMP POST BELLE HAVEN BUS STOP WIDENING, 1932. - George Washington Memorial Parkway, Along Potomac River from McLean to Mount Vernon, VA, Mount Vernon, Fairfax County, VA

Survey of transit bus maintenance programs in Virginia.

DOT National Transportation Integrated Search

1981-01-01

Transit bus maintenance practices as used by thirteen small and medium-sized transit systems in Virginia were cataloged. Different approaches to maintenance were investigated and the current condition of transit bus maintenance was determined. Factor...

Methodology of mixed load customized bus lines and adjustment based on time windows

PubMed Central

Song, Rui

2018-01-01

Custom bus routes need to be optimized to meet the needs of a customized bus for personalized trips of different passengers. This paper introduced a customized bus routing problem in which trips for each depot are given, and each bus stop has a fixed time window within which trips should be completed. Treating a trip as a virtual stop was the first consideration in solving the school bus routing problem (SBRP). Then, the mixed load custom bus routing model was established with a time window that satisfies its requirement and the result were solved by Cplex software. Finally, a simple network diagram with three depots, four pickup stops, and five delivery stops was structured to verify the correctness of the model, and based on the actual example, the result is that all the buses ran 124.42 kilometers, the sum of kilometers was 10.35 kilometers less than before. The paths and departure times of the different busses that were provided by the model were evaluated to meet the needs of the given conditions, thus providing valuable information for actual work. PMID:29320505

Exact and Metaheuristic Approaches for a Bi-Objective School Bus Scheduling Problem.

PubMed

Chen, Xiaopan; Kong, Yunfeng; Dang, Lanxue; Hou, Yane; Ye, Xinyue

2015-01-01

As a class of hard combinatorial optimization problems, the school bus routing problem has received considerable attention in the last decades. For a multi-school system, given the bus trips for each school, the school bus scheduling problem aims at optimizing bus schedules to serve all the trips within the school time windows. In this paper, we propose two approaches for solving the bi-objective school bus scheduling problem: an exact method of mixed integer programming (MIP) and a metaheuristic method which combines simulated annealing with local search. We develop MIP formulations for homogenous and heterogeneous fleet problems respectively and solve the models by MIP solver CPLEX. The bus type-based formulation for heterogeneous fleet problem reduces the model complexity in terms of the number of decision variables and constraints. The metaheuristic method is a two-stage framework for minimizing the number of buses to be used as well as the total travel distance of buses. We evaluate the proposed MIP and the metaheuristic method on two benchmark datasets, showing that on both instances, our metaheuristic method significantly outperforms the respective state-of-the-art methods.

Hybrid Turbine Electric Vehicle

NASA Technical Reports Server (NTRS)

Viterna, Larry A.

1997-01-01

Hybrid electric power trains may revolutionize today's ground passenger vehicles by significantly improving fuel economy and decreasing emissions. The NASA Lewis Research Center is working with industry, universities, and Government to develop and demonstrate a hybrid electric vehicle. Our partners include Bowling Green State University, the Cleveland Regional Transit Authority, Lincoln Electric Motor Division, the State of Ohio's Department of Development, and Teledyne Ryan Aeronautical. The vehicle will be a heavy class urban transit bus offering double the fuel economy of today's buses and emissions that are reduced to 1/10th of the Environmental Protection Agency's standards. At the heart of the vehicle's drive train is a natural-gas-fueled engine. Initially, a small automotive engine will be tested as a baseline. This will be followed by the introduction of an advanced gas turbine developed from an aircraft jet engine. The engine turns a high-speed generator, producing electricity. Power from both the generator and an onboard energy storage system is then provided to a variable-speed electric motor attached to the rear drive axle. An intelligent power-control system determines the most efficient operation of the engine and energy storage system.

Adaptive two-degree-of-freedom PI for speed control of permanent magnet synchronous motor based on fractional order GPC.

PubMed

Qiao, Wenjun; Tang, Xiaoqi; Zheng, Shiqi; Xie, Yuanlong; Song, Bao

2016-09-01

In this paper, an adaptive two-degree-of-freedom (2Dof) proportional-integral (PI) controller is proposed for the speed control of permanent magnet synchronous motor (PMSM). Firstly, an enhanced just-in-time learning technique consisting of two novel searching engines is presented to identify the model of the speed control system in a real-time manner. Secondly, a general formula is given to predict the future speed reference which is unavailable at the interval of two bus-communication cycles. Thirdly, the fractional order generalized predictive control (FOGPC) is introduced to improve the control performance of the servo drive system. Based on the identified model parameters and predicted speed reference, the optimal control law of FOGPC is derived. Finally, the designed 2Dof PI controller is auto-tuned by matching with the optimal control law. Simulations and real-time experimental results on the servo drive system of PMSM are provided to illustrate the effectiveness of the proposed strategy. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Intercity bus service in Virginia.

DOT National Transportation Integrated Search

1981-01-01

The intercity bus industry in Virginia was examined to gain information on the status of the industry and to determine the likely impacts of state policy options relating to assistance and deregulation on the industry. The national intercity bus indu...

LYMMO BRT : 15 years later.

DOT National Transportation Integrated Search

2013-06-01

LYMMO bus rapid transit service began in August 1997 in Orlando, Florida, : as one of the first bus-based premium downtown circulators in the U.S. Its : construction was funded, in part, by the Federal Transit Administrations (FTAs) : Bus Rapid...

75 FR 61341 - Airworthiness Directives; Agusta S.p.A. (Agusta) Model A109E Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-05

... electrical failure, an investigation revealed inadequate functioning of the 35 amperes (Amps) battery bus... investigation revealed inadequate functioning of the 35 amperes (Amps) battery bus (BATT BUS) circuit breaker...

Simulation of an Urban Battery Bus Vehicle

DOT National Transportation Integrated Search

1979-07-01

This report describes the computer simulation of a battery-powered bus as it traverses an arbitrary mission profile of specified acceleration, roadway grade, and headwind. The battery-bus system components comprise a DC shunt motor, solid-state power...

Evaluation guidelines for bus rapid transit demonstration projects

DOT National Transportation Integrated Search

2002-02-01

The Federal Transit Administration's (FTA) Bus Rapid Transit Demonstration Program is supporting demonstrations of Bus Rapid Transit (BRT) in selected cities across the United States. The US BRT Demonstration Program aims to adapt the principles of h...

Electric bus systems.

DOT National Transportation Integrated Search

2017-04-01

Pure electric buses (EBs) offer an alternative fuel for the nations transit bus systems. To : evaluate EBs in a transit setting, this project investigated the five electric bus fleet of the : StarMetro transit system of the city of Tallahassee, FL...

Small Explorer Data System MIL-STD-1773 fiber optic bus

NASA Technical Reports Server (NTRS)

Flanegan, Mark; Label, Ken

1992-01-01

The MIL-STD-1773 Fiber Optic Data Bus as implemented in the GSFC Small Explorer Data System (SEDS) for the Small Explorer Program is described. It provides an overview of the SEDS MIL-STD-1773 bus components system design considerations, reliability figures, acceptance and qualification testing requirements, radiation requirements and tests, error handling considerations, and component heritage. The first mission using the bus will be launched in June of 1992.

Building the vision, a series of AZTech ITS model deployment success stories for the Phoenix metropolitan area : number ten : high-tech transit, using state-of-the art technology to keep bus riders informed

DOT National Transportation Integrated Search

1998-01-01

Traditionally, the biggest problem experienced by transit riders is a lack of information. They may not have access to a bus schedule. Or, even if they do have a copy of the Bus Book, they have no way of : knowing if their particular bus is on schedu...

Methods of computing steady-state voltage stability margins of power systems

DOEpatents

Chow, Joe Hong; Ghiocel, Scott Gordon

2018-03-20

In steady-state voltage stability analysis, as load increases toward a maximum, conventional Newton-Raphson power flow Jacobian matrix becomes increasingly ill-conditioned so power flow fails to converge before reaching maximum loading. A method to directly eliminate this singularity reformulates the power flow problem by introducing an AQ bus with specified bus angle and reactive power consumption of a load bus. For steady-state voltage stability analysis, the angle separation between the swing bus and AQ bus can be varied to control power transfer to the load, rather than specifying the load power itself. For an AQ bus, the power flow formulation is only made up of a reactive power equation, thus reducing the size of the Jacobian matrix by one. This reduced Jacobian matrix is nonsingular at the critical voltage point, eliminating a major difficulty in voltage stability analysis for power system operations.

Concentrations of volatile organic compounds, carbon monoxide, carbon dioxide and particulate matter in buses on highways in Taiwan

NASA Astrophysics Data System (ADS)

Hsu, Der-Jen; Huang, Hsiao-Lin

2009-12-01

Although airborne pollutants in urban buses have been studied in many cities globally, long-distance buses running mainly on highways have not been addressed in this regard. This study investigates the levels of volatile organic compounds (VOCs), carbon monoxide (CO), carbon dioxide (CO 2) and particulate matter (PM) in the long-distance buses in Taiwan. Analytical results indicate that pollutants levels in long-distance buses are generally lower than those in urban buses. This finding is attributable to the driving speed and patterns of long-distance buses, as well as the meteorological and geographical features of the highway surroundings. The levels of benzene, toluene, ethylbenzene and xylene (BTEX) found in bus cabins exceed the proposed indoor VOC guidelines for aromatic compounds, and are likely attributable to the interior trim in the cabins. The overall average CO level is 2.3 ppm, with higher average level on local streets (2.9 ppm) than on highways (2.2 ppm). The average CO 2 level is 1493 ppm, which is higher than the guideline for non-industrial occupied settings. The average PM level in this study is lower than those in urban buses and IAQ guidelines set by Taiwan EPA. However, the average PM 10 and PM 2.5 is higher than the level set by WHO. Besides the probable causes mentioned above, fewer passenger movements and less particle re-suspension from bus floor might also cause the lower PM levels. Measurements of particle size distribution reveal that more than 75% of particles are in submicron and smaller sizes. These particles may come from the infiltration from the outdoor air. This study concludes that air exchange rates in long-distance buses should be increased in order to reduce CO 2 levels. Future research on long-distance buses should focus on the emission of VOCs from brand new buses, and the sources of submicron particles in bus cabins.

Method for reworkable packaging of high speed, low electrical parasitic power electronics modules through gate drive integration

DOEpatents

Passmore, Brandon; Cole, Zach; Whitaker, Bret; Barkley, Adam; McNutt, Ty; Lostetter, Alexander

2016-08-02

A multichip power module directly connecting the busboard to a printed-circuit board that is attached to the power substrate enabling extremely low loop inductance for extreme environments such as high temperature operation. Wire bond interconnections are taught from the power die directly to the busboard further enabling enable low parasitic interconnections. Integration of on-board high frequency bus capacitors provide extremely low loop inductance. An extreme environment gate driver board allows close physical proximity of gate driver and power stage to reduce overall volume and reduce impedance in the control circuit. Parallel spring-loaded pin gate driver PCB connections allows a reliable and reworkable power module to gate driver interconnections.

Distance from public transportation and physical activity in Japanese older adults: The moderating role of driving status.

PubMed

Harada, Kazuhiro; Lee, Sangyoon; Lee, Sungchul; Bae, Seongryu; Anan, Yuya; Harada, Kenji; Shimada, Hiroyuki

2018-04-01

Although previous studies have shown that good access to public transportation is positively related with physical activity, the moderators of this relationship have not been explored sufficiently in older adults. It is possible that driving status could moderate this relationship. The present study examined whether the objectively measured distance between public transportation and the home was associated with physical activity levels, and whether this association was moderated by driving status among Japanese older adults. In this cross-sectional study, participants (n = 2,878) completed questionnaires and wore accelerometers for at least 7 days, to measure their average daily step counts and minutes spent engaging in moderate-to-vigorous physical activity. Road network distances between the home and the nearest bus stop or train station were measured using geographic information systems. Driving status was assessed using questionnaires. Multiple regression analyses stratified by driving status revealed that, among nondrivers, living further away from public transportation was associated with higher step counts (β = 0.08, p < .001) and moderate-to-vigorous physical activity (β = 0.06, p = .029). Among drivers, living closer to public transportation was significantly associated with higher moderate-to-vigorous physical activity levels (β = -0.05, p = .042). Despite the small effect sizes, the direction of the association between distance from public transportation and physical activity was different for current drivers and nondrivers. These findings imply that good access to public transportation does not positively relate with greater engagement in physical activity among nondriving older adults. Shorter distances to public transportation might reduce opportunities for engaging in physical activity for them. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Pennsylvania intercity bus study : final report

DOT National Transportation Integrated Search

1984-09-01

Report presents the findings of a study to inventory the intercity bus industry in Pennsylvania. Objectives were to assemble information about the intercity bus industry in Pennsylvania in a form that can be used for policy formulation and for manage...

The bus transit system : ITS underutilized potential

DOT National Transportation Integrated Search

1994-05-01

The bus system represents the most widely used transit mode. Upgraded bus services, primarily those which have partially or fully separated rights-of-way, represent a very cost-effective method to improve the balance between automobile and transit. M...

Proceedings of Bus Summit 2000 : ensuring a healthy U.S. bus industry

DOT National Transportation Integrated Search

2000-10-01

The Federal Transit Administration (FTA) Bus Industry Summit was held October 18-19, 2000, in Washington, DC. The Summit offered an opportunity for representatives from the transit industry, including transit providers, vehicle manufacturers, consult...

San Antonio's 1983 Bus Passenger Survey

DOT National Transportation Integrated Search

1983-10-01

Many transit operators routinely collect ridership data in order to provide a : basis for the planning of bus services. Often a survey is conducted of bus : riders to determine their riding habits, their views about the quality of : current service, ...

Chattanooga SmartBus Project : phase III evaluation report

DOT National Transportation Integrated Search

2009-12-01

This report presents the results of Phase III of the national evaluation of the Chattanooga Area Regional Transportation Authoritys (CARTA) SmartBus Project. The SmartBus Project is a comprehensive transit ITS program for the city of Chattanooga, ...

Demonstrating a Total Transit Solution for Fuel Cell Electric Buses in Boston

DOT National Transportation Integrated Search

2017-05-01

The Federal Transit Administrations (FTA) National Fuel Cell Bus Program (NFCBP) focuses on developing commercially viable fuel cell bus technologies. Nuvera is leading the Massachusetts Fuel Cell Bus project to demonstrate a complete transit solu...

Mass transit : bus rapid transit shows promise

DOT National Transportation Integrated Search

2001-09-17

The U. S. General Accounting Office (GAO) was asked to (1) examine the federal role in supporting Bus Rapid Transit; (2) compare the capital costs, operating costs, and performance characteristics of Bus Rapid Transit and Light Rail systems; and (3) ...

The crew activity planning system bus interface unit

NASA Technical Reports Server (NTRS)

Allen, M. A.

1979-01-01

The hardware and software designs used to implement a high speed parallel communications interface to the MITRE 307.2 kilobit/second serial bus communications system are described. The primary topic is the development of the bus interface unit.

King County Metro Battery Electric Bus Demonstration—Preliminary Project Results

DOT National Transportation Integrated Search

2017-05-01

The U.S. Federal Transit Administration (FTA) funds a variety of research projects that support the commercialization of zero-emission bus technology. Recent programs include the National Fuel Cell Bus program, the Transit Investments for Greenhouse ...

Bus transportation in Connecticut : data for planning, agenda for action

DOT National Transportation Integrated Search

1974-03-01

Presents the conclusions and recommendations of the Connecticut Public Expenditure Council regarding the present status of bus transit service throughout Connecticut; operational and funding issues; status of bus transit elsewhere in the U. S. and se...

Method and system for pipeline communication

DOEpatents

Richardson,; John, G [Idaho Falls, ID

2008-01-29

A pipeline communication system and method includes a pipeline having a surface extending along at least a portion of the length of the pipeline. A conductive bus is formed to and extends along a portion of the surface of the pipeline. The conductive bus includes a first conductive trace and a second conductive trace with the first and second conductive traces being adapted to conformally couple with a pipeline at the surface extending along at least a portion of the length of the pipeline. A transmitter for sending information along the conductive bus on the pipeline is coupled thereto and a receiver for receiving the information from the conductive bus on the pipeline is also couple to the conductive bus.

Methods for Trustworthy Design of On-Chip Bus Interconnect for General-Purpose Processors

DTIC Science & Technology

2012-03-01

Technology Andrew Huang, was able to test the security properties of HyperTransport bus protocol on an Xbox [20]. In his research, he was able to...TRUSTWORTHY DESIGN OF ON -CHIP BUS INTERCONNECT FOR GENERAL-PURPOSE PROCESSORS by Jay F. Elson March 2012 Thesis Advisor: Ted Huffmire Second...AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE Methods for Trustworthy Design of On -Chip Bus Interconnect for General-Purpose Processors 5

ALR-46 Computer Graphics System for the Robins Air Force Base Electronic Warfare Division Engineering Branch Laboratory.

DTIC Science & Technology

1981-12-01

CGS Funtional Requirements and System Configuration Introduction The first phase of any system development is to define requirements. The development of...between any two devices and the bus is in a master/slave relationship . During any bus operation, the bus master controls the bus when communicating with...illustrate the CASE statement of the PASCAL language. These extensions are mentioned to illustrate the relationships that the Warnier-Orr diagrams exhibit

Heavy Duty Diesel Truck and Bus Hybrid Powertrain Study

DTIC Science & Technology

2012-03-01

electric 22 ft. bus that offers greater range than battery-electric buses can provide. Designed to seat 22 passengers plus standees, this Ebus model...system that has both parallel and series operating modes. The relatively low volume of many truck and bus designs has inhibited the development of...that battery packs need to be designed for 50,000 lifetime energy storage cycles in a hybrid transit bus vs. just 3,600 cycles in the typical

Design of a 500 MJ, 5 MA power supply

NASA Astrophysics Data System (ADS)

Pappas, J. A.; Headifen, G. R.; Weldon, J. M.; Wright, J. C.; Zowarka, R. C.; Aanstoos, T. A.; Kajs, J. H.

1993-01-01

The design of a 500 MJ, 5 MA power supply for rail gun experiments under the Battery Upgraded Supply (BUS) program is examined. About 50,000 12-volt lead acid batteries are required to reach this level. BUS will be required to perform up to two discharges per week. Therefore, BUS is designed to be a low-maintenance, reliable, and fault-tolerant power supply. The design of BUS and the details of its subsystems are described.

Performance Analysis of Trans-Jakarta Bus Suburban Service Move-Across Greater Jakarta

NASA Astrophysics Data System (ADS)

Tangkudung, ESW; Widyadayinta, C.

2018-03-01

Trans-Jakarta have developed their services scope as Suburban Service or Feeder move-across service that operate from greater Jakarta into Jakarta central vice versa. One of the route is Ciputat – Bundaran Hotel Indonesia (Tosari) and integrated with corridor 1 (one) and 8 (eight). This service is not travel on the exclusive lane or bus-way. Objective of Government Jakarta to provide this service is to decrease private car to enter the central of Jakarta. The objective of this study is to find the performance of the service. Survey have conducted static and dynamic on work day to get variable of travel time and delay, waiting time of passenger at the bus stop, headway and ridership of the bus. Service Standard Minimum of Trans-Jakarta have compared with the result of variable headway, travel speed, and waiting time at bus stop as concern of all the passengers. Analysis use correlation test method and linear regression model have done. The performance of Trans-Jakarta bus suburban service, based on travel speed indicator is fairly bad, only 8.1% of trip could comply with Minimum Service Standard. Bus performance based on the indicator of density in the bus is good, where all points are below the maximum limit i.e. 8 people/m2 at peak hour and 5 people/m2 at off-peak hour.

Task Analysis Assessment on Intrastate Bus Traffic Controllers

NASA Astrophysics Data System (ADS)

Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

2016-11-01

Public transportation acts as social mobility and caters the daily needs of the society for passengers to travel from one place to another. This is true for a country like Malaysia where international trade has been growing significantly over the past few decades. Task analysis assessment was conducted with the consideration of cognitive ergonomic view towards problem related to human factors. Conducting research regarding the task analysis on bus traffic controllers had allowed a better understanding regarding the nature of work and the overall monitoring activities of the bus services. This paper served to study the task analysis assessment on intrastate bus traffic controllers and the objectives of this study include to conduct task analysis assessment on the bus traffic controllers. Task analysis assessment for the bus traffic controllers was developed via Hierarchical Task Analysis (HTA). There are a total of five subsidiary tasks on level one and only two were able to be further broken down in level two. Development of HTA allowed a better understanding regarding the work and this could further ease the evaluation of the tasks conducted by the bus traffic controllers. Thus, human error could be reduced for the safety of all passengers and increase the overall efficiency of the system. Besides, it could assist in improving the operation of the bus traffic controllers by modelling or synthesizing the existing tasks if necessary.

Ultra-Capacitor Energy Storage in a Large Hybrid Electric Bus

NASA Technical Reports Server (NTRS)

Viterna, L. A.

1997-01-01

The power requirements for inner city transit buses are characterized by power peaks about an order of magnitude larger than the average power usage of the vehicle. For these vehicles, hybrid power trains can offer significantly improved fuel economy and exhaust emissions. A critical design challenge, however, has been developing the energy storage and power management system to respond to these rapid power variations. Most hybrid vehicles today use chemical energy storage batteries to supplement the power from the fuel burning generator unit. Chemical storage batteries however, present several difficulties in power management and control. These difficulties include (1) inadequate life, (2) limited current delivery as well as absorption during regenerative braking, (3) inaccurate measurement of state of charge, and (4) stored energy safety issues. Recent advances in ultra-capacitor technology create an opportunity to address these concerns. The NASA Lewis Research Center, in cooperation with industry and academia, has developed an advanced hybrid electric transit bus using ultra-capacitors as the primary energy storage system. At over 15,000-kg gross weight, this is the largest vehicle of its kind ever built using this advanced energy storage technology. Results of analyses show that the vehicle will match the performance of an equivalent conventionally powered vehicle over typical inner city drive cycles. This paper describes the overall power system architecture, the evolution of the control strategy, and analysis of power flow and vehicle performance.

Development of an EtherCAT enabled digital servo controller for the Green Bank Telescope

NASA Astrophysics Data System (ADS)

Whiteis, Peter G.; Mello, Melinda J.

2012-09-01

EtherCAT (Ethernet for Control Automation Technology) is gaining wide spread popularity in the automation industry as a real time field bus based on low cost, Ethernet hardware. EtherCAT maximizes use of 100Mbps Ethernet hardware by using a collision free ring topology, efficient Ethernet frame utilization (> 95%), and data exchange "on the fly". These characteristics enable EtherCAT to achieve Master to Slave node data exchange rates of > 1000 Hz. The Green Bank Telescope, commissioned in 2000, utilizes an analog control system for motion control of 8 elevation and 16 azimuth motors. This architecture, while sufficient for observations at frequencies up to 50GHz, has significant limitations for the current scientific goals of observing at 115GHz. Accordingly, the Green Bank staff has embarked on a servo upgrade project to develop a digital servo system which accommodates development and implementation of advanced control algorithms. This paper describes how the new control system requirements, use of existing infrastructure and budget constraints led us to define a distributed motion control architecture where EtherCAT real-time Ethernet was selected as the communication bus. Finally, design details are provided that describe how NRAO developed a custom EtherCAT-enabled motor controller interface for the GBT's legacy motor drives in order to provide technical benefits and flexibility not available in commercial products.

Noise Reduction Retrofit for a "New Look" Flexible Transit Bus Service Bulletin

DOT National Transportation Integrated Search

1980-09-01

This document presents instructions on how to apply a noise treatment to a contemporary city transit bus without extensive structural alteration. Baseline bus configuration, noise ratings, and performance benchmarks are presented for a Flexible 111DC...

Air Conditioning Modifications for the GMC RTSII Series 01 Coach (Model TH 8201)

DOT National Transportation Integrated Search

1982-10-01

As part of its bus and paratransit technology research and development efforts, the Urban Mass Transportation Administration is conducting the Bus Subsystems Technology Project to help the transit bus industry solve serious equipment problems. The pr...

District of Columbia tour bus management initiative final report.

DOT National Transportation Integrated Search

2003-10-01

The objective of the District of Columbia Tour Bus Management Initiative is to develop a plan that will ameliorate the long-standing problems, as identified above, that negatively affect tour bus operations as well as traffic conditions, the visitor ...

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

DOT National Transportation Integrated Search

2008-10-16

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

Developing and Demonstrating the Next-Generation Fuel Cell Electric Bus Made in America

DOT National Transportation Integrated Search

2012-02-01

The Federal Transit Administrations (FTA) National Fuel Cell Bus Program (NFCBP) focuses on developing commercially viable fuel cell bus technologies. CALSTART is one of three non-profit consortia chosen to manage projects competitively selected u...

Connecticut DOT statewide bus system study : executive summary

DOT National Transportation Integrated Search

2000-07-01

The Connecticut Statewide Bus System Study has been undertaken to ensure that bus transit in Connecticut serves continuing needs in the most efficient manner possible. The Study has taken a comprehensive look at the state's twenty urban and rural tra...

Integration of Fixed and Flexible Route Public Transportation Systems, Phase II

DOT National Transportation Integrated Search

2012-01-01

Conventional bus service (with fixed routes and schedules) has lower average cost than flexible bus service (with : demand-responsive routes) at high demand densities. At low demand densities flexible bus service has lower : average costs and provide...

Bus Lifecycle Cost Model for Federal Land Management Agencies.

DOT National Transportation Integrated Search

2011-09-30

The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

Traffic safety facts 1993 : school buses

DOT National Transportation Integrated Search

1994-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1983, 1,572 people h...

Traffic safety facts 1995 : school buses

DOT National Transportation Integrated Search

1996-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1985, 1,478 people h...

Traffic safety facts 1994 : school buses

DOT National Transportation Integrated Search

1995-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1984, 1,517 people h...

Traffic safety facts 2000 : school buses

DOT National Transportation Integrated Search

2001-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1990, 1,450 people h...

Traffic safety facts 1996 : school buses

DOT National Transportation Integrated Search

1997-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1986, 1,458 people h...

Traffic safety facts 1998 : school buses

DOT National Transportation Integrated Search

1999-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1988, 1,409 people h...

Traffic safety facts 1999 : school buses

DOT National Transportation Integrated Search

2000-01-01

A school bus-related crash is a crash which involves, either directly or indirectly, a school bus-type vehicle, or a vehicle functioning as a school bus, transporting children to or from school or school-related activities. Since 1989, 1,445 people h...

Connecticut nutmeg fuel cell bus project : first analysis report.

DOT National Transportation Integrated Search

2012-07-01

This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administra-tion (FTA) under the National Fuel Cell Bus Program (NFCBP). A team led by the Northeast Advanced Vehicle Consortium a...

Combined comfort model of thermal comfort and air quality on buses in Hong Kong.

PubMed

Shek, Ka Wing; Chan, Wai Tin

2008-01-25

Air-conditioning settings are important factors in controlling the comfort of passengers on buses. The local bus operators control in-bus air quality and thermal environment by conforming to the prescribed levels stated in published standards. As a result, the settings are merely adjusted to fulfill the standards, rather than to satisfy the passengers' thermal comfort and air quality. Such "standard-oriented" practices are not appropriate; the passengers' preferences and satisfaction should be emphasized instead. Thus a "comfort-oriented" philosophy should be implemented to achieve a comfortable in-bus commuting environment. In this study, the achievement of a comfortable in-bus environment was examined with emphasis on thermal comfort and air quality. Both the measurement of physical parameters and subjective questionnaire surveys were conducted to collect practical in-bus thermal and air parameters data, as well as subjective satisfaction and sensation votes from the passengers. By analyzing the correlation between the objective and subjective data, a combined comfort models were developed. The models helped in evaluating the percentage of dissatisfaction under various combinations of passengers' sensation votes towards thermal comfort and air quality. An effective approach integrated the combined comfort model, hardware and software systems and the bus air-conditioning system could effectively control the transient in-bus environment. By processing and analyzing the data from the continuous monitoring system with the combined comfort model, air-conditioning setting adjustment commands could be determined and delivered to the hardware. This system adjusted air-conditioning settings depending on real-time commands along the bus journey. Therefore, a comfortable in-bus air quality and thermal environment could be achieved and efficiently maintained along the bus journey despite dynamic outdoor influences. Moreover, this model can help optimize air-conditioning control by striking a beneficial balance between energy conservation and passengers' satisfaction level.

In-use fuel economy of hybrid-electric school buses in Iowa.

PubMed

Hallmark, Shauna; Sperry, Bob; Mudgal, Abhisek

2011-05-01

Although it is much safer and more fuel-efficient to transport children to school in buses than in private vehicles, school buses in the United States still consume 822 million gal of diesel fuel annually, and school transportation costs can account for a significant portion of resource-constrained school district budgets. Additionally, children in diesel-powered school buses may be exposed to higher levels of particulates and other pollutants than children in cars. One solution to emission and fuel concerns is use of hybrid-electric school buses, which have the potential to reduce emissions and overall lifecycle costs compared with conventional diesel buses. Hybrid-electric technologies are available in the passenger vehicle market as well as the transit bus market and have a track record indicating fuel economy and emissions benefits. This paper summarizes the results of an in-use fuel economy evaluation for two plug-in hybrid school buses deployed in two different school districts in Iowa. Each school district selected a control bus with a route similar to that of the hybrid bus. Odometer readings, fuel consumption, and maintenance needs were recorded for each bus. The buses were deployed in 2008 and data were collected through May 2010. Fuel consumption was calculated for each school district. In Nevada, IA, the overall average fuel economy was 8.23 mpg for the hybrid and 6.35 mpg for the control bus. In Sigourney, IA, the overall average fuel economy was 8.94 mpg for the hybrid and 6.42 mpg for the control bus. The fuel consumption data were compared for the hybrid and control buses using a Wilcoxon signed rank test. Results indicate that fuel economy for the Nevada hybrid bus was 29.6% better than for the Nevada control bus, and fuel economy for the Sigourney hybrid bus was 39.2% higher than for the Sigourney control bus. Both differences were statistically significant.

Cluster Inter-Spacecraft Communications

NASA Technical Reports Server (NTRS)

Cox, Brian

2008-01-01

A document describes a radio communication system being developed for exchanging data and sharing data-processing capabilities among spacecraft flying in formation. The system would establish a high-speed, low-latency, deterministic loop communication path connecting all the spacecraft in a cluster. The system would be a wireless version of a ring bus that complies with the Institute of Electrical and Electronics Engineers (IEEE) standard 1393 (which pertains to a spaceborne fiber-optic data bus enhancement to the IEEE standard developed at NASA's Jet Propulsion Laboratory). Every spacecraft in the cluster would be equipped with a ring-bus radio transceiver. The identity of a spacecraft would be established upon connection into the ring bus, and the spacecraft could be at any location in the ring communication sequence. In the event of failure of a spacecraft, the ring bus would reconfigure itself, bypassing a failed spacecraft. Similarly, the ring bus would reconfigure itself to accommodate a spacecraft newly added to the cluster or newly enabled or re-enabled. Thus, the ring bus would be scalable and robust. Reliability could be increased by launching, into the cluster, spare spacecraft to be activated in the event of failure of other spacecraft.

Comparative study of fuel cell, battery and hybrid buses for renewable energy constrained areas

NASA Astrophysics Data System (ADS)

Stempien, J. P.; Chan, S. H.

2017-02-01

Fuel cell- and battery-based public bus technologies are reviewed and compared for application in tropical urban areas. This paper scrutinizes the reported literature on fuel cell bus, fuel cell electric bus, battery electric bus, hybrid electric bus, internal combustion diesel bus and compressed natural gas bus. The comparison includes the capital and operating costs, fuel consumption and fuel cycle emissions. To the best of authors knowledge, this is the first study to holistically compare hydrogen and battery powered buses, which is the original contribution of this paper. Moreover, this is the first study to focus on supplying hydrogen and electricity from fossil resources, while including the associated emissions. The study shows that compressed natural gas and hybrid electric buses appear to be the cheapest options in terms of total cost of ownership, but they are unable to meet the EURO VI emissions' standard requirement. Only fuel cell based buses have the potential to achieve the emissions' standard when the fuel cycle based on fossil energy was considered. Fuel cell electric buses are identified as a technology allowing for the largest CO2 emission reduction, making ∼61% decrease in annual emissions possible.

Evaluation of Effective Factors on Travel Time in Optimization of Bus Stops Placement Using Genetic Algorithm

NASA Astrophysics Data System (ADS)

Bargegol, Iraj; Ghorbanzadeh, Mahyar; Ghasedi, Meisam; Rastbod, Mohammad

2017-10-01

In congested cities, locating and proper designing of bus stops according to the unequal distribution of passengers is crucial issue economically and functionally, since this subject plays an important role in the use of bus system by passengers. Location of bus stops is a complicated subject; by reducing distances between stops, walking time decreases, but the total travel time may increase. In this paper, a specified corridor in the city of Rasht in north of Iran is studied. Firstly, a new formula is presented to calculate the travel time, by which the number of stops and consequently, the travel time can be optimized. An intended corridor with specified number of stops and distances between them is addressed, the related formulas to travel time are created, and its travel time is calculated. Then the corridor is modelled using a meta-heuristic method in order that the placement and the optimal distances of bus stops for that are determined. It was found that alighting and boarding time along with bus capacity are the most effective factors affecting travel time. Consequently, it is better to have more concentration on indicated factors for improving the efficiency of bus system.

Optimal PMU placement using topology transformation method in power systems.

PubMed

Rahman, Nadia H A; Zobaa, Ahmed F

2016-09-01

Optimal phasor measurement units (PMUs) placement involves the process of minimizing the number of PMUs needed while ensuring the entire power system completely observable. A power system is identified observable when the voltages of all buses in the power system are known. This paper proposes selection rules for topology transformation method that involves a merging process of zero-injection bus with one of its neighbors. The result from the merging process is influenced by the selection of bus selected to merge with the zero-injection bus. The proposed method will determine the best candidate bus to merge with zero-injection bus according to the three rules created in order to determine the minimum number of PMUs required for full observability of the power system. In addition, this paper also considered the case of power flow measurements. The problem is formulated as integer linear programming (ILP). The simulation for the proposed method is tested by using MATLAB for different IEEE bus systems. The explanation of the proposed method is demonstrated by using IEEE 14-bus system. The results obtained in this paper proved the effectiveness of the proposed method since the number of PMUs obtained is comparable with other available techniques.

Exact and Metaheuristic Approaches for a Bi-Objective School Bus Scheduling Problem

PubMed Central

Chen, Xiaopan; Kong, Yunfeng; Dang, Lanxue; Hou, Yane; Ye, Xinyue

2015-01-01

As a class of hard combinatorial optimization problems, the school bus routing problem has received considerable attention in the last decades. For a multi-school system, given the bus trips for each school, the school bus scheduling problem aims at optimizing bus schedules to serve all the trips within the school time windows. In this paper, we propose two approaches for solving the bi-objective school bus scheduling problem: an exact method of mixed integer programming (MIP) and a metaheuristic method which combines simulated annealing with local search. We develop MIP formulations for homogenous and heterogeneous fleet problems respectively and solve the models by MIP solver CPLEX. The bus type-based formulation for heterogeneous fleet problem reduces the model complexity in terms of the number of decision variables and constraints. The metaheuristic method is a two-stage framework for minimizing the number of buses to be used as well as the total travel distance of buses. We evaluate the proposed MIP and the metaheuristic method on two benchmark datasets, showing that on both instances, our metaheuristic method significantly outperforms the respective state-of-the-art methods. PMID:26176764

An evaluation of the Shirley Highway Express-Bus-on-Freeway Demonstration Project.

DOT National Transportation Integrated Search

1973-01-01

The Shirley Highway Express-Bus-on-Freeway Demonstration Project was initiated to test the hypothesis that the provision of rapid and convenient bus service over an exclusive lane would attract significant numbers of automobile passengers. Such a div...

Integration of bus stop counts data with census data for improving bus service.

DOT National Transportation Integrated Search

2016-04-01

This research project produced an open source transit market data visualization and analysis tool suite, : The Bus Transit Market Analyst (BTMA), which contains user-friendly GIS mapping and data : analytics tools, and state-of-the-art transit demand...

Front Range commuter bus study. Phase 2 : final report

DOT National Transportation Integrated Search

2003-10-01

The goal of Front Range Commuter Bus service would be to provide a commuter bus service that would operate seamlessly with local transit systems and would be run through a partnership with each of the cities, CDOT, RTD and participating private provi...

Automated Bus Diagnostic System Demonstration in New York City

DOT National Transportation Integrated Search

1983-12-01

In response to a growing problem with the quality and efficiency of nationwide bus maintenance practices, an award was granted to the Tri-State Regional Planning Commission for the testing of an automated bus diagnostic system (ABDS). The ABDS was de...

American Fuel Cell Bus Project Evaluation : Third Report

DOT National Transportation Integrated Search

2017-05-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses (FCEB) operating in the Coachella Valley area of California. The AFCB, built on an ElDorado National-California 40-foot Axess bus p...

Haverhill, Mass. School Bus Company Reduces Idling Under Settlement

EPA Pesticide Factsheets

Coppola Bus, Inc., a Haverhill, Mass. company has reduced vehicle idling and therefore reduced diesel emissions, and paid an $18,000 penalty as part of a settlement with the U.S. Environmental Protection Agency for claims of excessive school bus idling.

Connecticut Nutmeg Fuel Cell Bus Project : Demonstrating Advanced-Design Hybrid Fuel Cell Buses in Connecticut

DOT National Transportation Integrated Search

2011-07-01

The Federal Transit Administrations (FTA) National Fuel Cell Bus Program (NFCBP) focuses on developing commercially viable fuel cell bus technologies. The Northeast Advanced Vehicle Consortium (NAVC) is one of three non-profit consortia chosen to ...

Development and evaluation of a pedestrian safety training program for elementary school bus riders

DOT National Transportation Integrated Search

1994-12-01

The objective of this study was to develop and evaluate a comprehensive pedestrian safety program for elementary (kindergarten through grade 6) school bus riders. Existing materials, crash data and state laws/regulations on school bus pedestrian safe...

Radiation-Tolerant Dual Data Bus

NASA Technical Reports Server (NTRS)

Kinstler, Gary A.

2007-01-01

An architecture, and a method of utilizing the architecture, have been proposed to enable error-free operation of a data bus that includes, and is connected to, commercial off-the-shelf (COTS) circuits and components that are inherently susceptible to singleevent upsets [SEUs (bit flips caused by impinging high-energy particles and photons)]. The architecture and method are applicable, more specifically, to data-bus circuitry based on the Institute for Electrical and Electronics Engineers (IEEE) 1394b standard for a high-speed serial bus.

System level latchup mitigation for single event and transient radiation effects on electronics

DOEpatents

Kimbrough, J.R.; Colella, N.J.

1997-09-30

A ``blink`` technique, analogous to a person blinking at a flash of bright light, is provided for mitigating the effects of single event current latchup and prompt pulse destructive radiation on a micro-electronic circuit. The system includes event detection circuitry, power dump logic circuitry, and energy limiting measures with autonomous recovery. The event detection circuitry includes ionizing radiation pulse detection means for detecting a pulse of ionizing radiation and for providing at an output terminal thereof a detection signal indicative of the detection of a pulse of ionizing radiation. The current sensing circuitry is coupled to the power bus for determining an occurrence of excess current through the power bus caused by ionizing radiation or by ion-induced destructive latchup of a semiconductor device. The power dump circuitry includes power dump logic circuitry having a first input terminal connected to the output terminal of the ionizing radiation pulse detection circuitry and having a second input terminal connected to the output terminal of the current sensing circuitry. The power dump logic circuitry provides an output signal to the input terminal of the circuitry for opening the power bus and the circuitry for shorting the power bus to a ground potential to remove power from the power bus. The energy limiting circuitry with autonomous recovery includes circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential. The circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential includes a series FET and a shunt FET. The invention provides for self-contained sensing for latchup, first removal of power to protect latched components, and autonomous recovery to enable transparent operation of other system elements. 18 figs.

System level latchup mitigation for single event and transient radiation effects on electronics

DOEpatents

Kimbrough, Joseph Robert; Colella, Nicholas John

1997-01-01

A "blink" technique, analogous to a person blinking at a flash of bright light, is provided for mitigating the effects of single event current latchup and prompt pulse destructive radiation on a micro-electronic circuit. The system includes event detection circuitry, power dump logic circuitry, and energy limiting measures with autonomous recovery. The event detection circuitry includes ionizing radiation pulse detection means for detecting a pulse of ionizing radiation and for providing at an output terminal thereof a detection signal indicative of the detection of a pulse of ionizing radiation. The current sensing circuitry is coupled to the power bus for determining an occurrence of excess current through the power bus caused by ionizing radiation or by ion-induced destructive latchup of a semiconductor device. The power dump circuitry includes power dump logic circuitry having a first input terminal connected to the output terminal of the ionizing radiation pulse detection circuitry and having a second input terminal connected to the output terminal of the current sensing circuitry. The power dump logic circuitry provides an output signal to the input terminal of the circuitry for opening the power bus and the circuitry for shorting the power bus to a ground potential to remove power from the power bus. The energy limiting circuitry with autonomous recovery includes circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential. The circuitry for opening the power bus and circuitry for shorting the power bus to a ground potential includes a series FET and a shunt FET. The invention provides for self-contained sensing for latchup, first removal of power to protect latched components, and autonomous recovery to enable transparent operation of other system elements.

Concept Study on a Flexible Standard Bus for Small Scientific Satellites

NASA Astrophysics Data System (ADS)

Fukuda, Seisuke; Sawai, Shujiro; Sakai, Shin-Ichiro; Saito, Hirobumi; Tohma, Takayuki; Takahashi, Junko; Toriumi, Tsuyoshi; Kitade, Kenji

In this paper, a new standard bus system for a series of small scientific satellites in the Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency (ISAS/JAXA) is described. Since each mission proposed for the series has a wide variety of requirements, a lot of efforts are needed to enhance flexibility of the standard bus. Some concepts from different viewpoints are proposed. First, standardization layers concerning satellite configuration, instruments, interfaces, and design methods are defined respectively. Methods of product platform engineering, which classify specifications of the bus system into a core platform, alternative variants, and selectable variants, are also investigated in order to realize a semi-custom-made bus. Furthermore, a tradeoff between integration and modularization architecture is fully considered.

A fatal impaling injury in a road traffic accident: a case report.

PubMed

Rautji, R; Girdhar, S; Lalwani, S; Dogra, T D

2004-04-01

A 17-year old, thin-built male was sitting in a bus on the right side of the rear seat. The same side of the bus accidentally hit some iron rods, meant for construction work, projecting from the tail end of a small truck. The incident happened when the bus driver tried to manoeuvre the bus towards the left side of the truck, standing at a red traffic light intersection. One of the iron-rods entered the bus through the glass window next to which the victim had been sitting and penetrated his chest cavity from the side, lacerating both the lungs and exiting through the left shoulder blade. The individual died on his way to hospital.

Direct Drive Hall Thruster System Development

NASA Technical Reports Server (NTRS)

Hoskins, W. Andrew; Homiak, Daniel; Cassady, R. Joseph; Kerslake, Tom; Peterson, Todd; Ferguson, Dale; Snyder, Dave; Mikellides, Ioannis; Jongeward, Gary; Schneider, Todd

2003-01-01

The sta:us of development of a Direct Drive Ha!! Thruster System is presented. 13 the first part. a s:udy of the impacts to spacecraft systems and mass benefits of a direct-drive architecture is reviewed. The study initially examines four cases of SPT-100 and BPT-4000 Hall thrusters used for north-south station keeping on an EXPRESS-like geosynchronous spacecraft and for primary propulsion for a Deep Space- 1 based science spacecraft. The study is also extended the impact of direct drive on orbit raising for higher power geosynchronous spacecraft and on other deep space missions as a function of power and delta velocity. The major system considerations for accommodating a direct drive Hall thruster are discussed, including array regulation, system grounding, distribution of power to the spacecraft bus, and interactions between current-voltage characteristics for the arrays and thrusters. The mass benefit analysis shows that, for the initial cases, up to 42 kg of dry mass savings is attributable directly to changes in the propulsion hardware. When projected mass impacts of operating the arrays and the electric power system at 300V are included, up to 63 kg is saved for the four initial cases. Adoption of high voltage lithium ion battery technology is projected to further improve these savings. Orbit raising of higher powered geosynchronous spacecraft, is the mission for which direct drive provides the most benefit, allowing higher efficiency electric orbit raising to be accomplished in a limited period of time, as well as nearly eliminating significant power processing heat rejection mass. The total increase in useful payload to orbit ranges up to 278 kg for a 25 kW spacecraft, launched from an Atlas IIA. For deep space missions, direct drive is found to be most applicable to higher power missions with delta velocities up to several km/s , typical of several Discovery-class missions. In the second part, the status of development of direct drive propulsion power electronics is presented. The core of this hardware is the heater-keeper-magnet supply being qualified for the BPT-4000 by Aerojet. A breadboard propulsion power unit is in fabrication and is scheduled for delivery late in 2003.

Advanced Vehicle Monitoring And Communication Systems For Bus Transit Benefits And Economic Feasibility

DOT National Transportation Integrated Search

1993-03-01

THIS REPORT ANALYZES THE FEASIBILITY OF ADVANCED VEHICLE MONITORING AND COMMUNICATION (AVM/C) SYSTEMS FOR BUS TRANSIT IN THE UNITED STATES. SUCH SYSTEMS ARE WIDELY USED IN EUROPE AND CANADA TO PROVIDE MORE RELIABLE AND EFFICIENT BUS SERVICES, BUT HAV...

Advanced Vehicle Monitoring And Communication Systems For Bus Transit, Benefits And Economic Feasibility

DOT National Transportation Integrated Search

1991-09-01

THIS REPORT ANALYZES THE FEASIBILITY OF ADVANCED VEHICLE MONITORING AND COMMUNICATION (AVM/C) SYSTEMS FOR BUS TRANSIT IN THE UNITED STATES. SUCH SYSTEMS ARE WIDELY USED IN EUROPE AND CANADA TO PROVIDE MORE RELIABLE AND EFFICIENT BUS SERVICES, BUT HAV...

Shared-use bus priority lanes on city streets : case studies in design and management

DOT National Transportation Integrated Search

2012-04-01

This report examines the policies and strategies governing the design and, especially, operations of bus lanes in major congested urban centers. It focuses on bus lanes that operate in mixed traffic conditions; the study does not examine practices co...

Peer-to-peer information exchange on bus rapid transit (BRT) and bus priority best practices.

DOT National Transportation Integrated Search

2012-05-01

The purpose of this effort was to foster a dialogue among peers at transportation and planning agencies about their experiences with : promoting public transit and, in particular, the challenges they face related to Bus Rapid Transit (BRT) projects, ...

Improving School Bus Driver Performance.

ERIC Educational Resources Information Center

Farmer, Ernest

This reference source is intended to assist the school bus driver training instructor in course preparation. Instructional units for program planning each contain pertinent course questions, a summary, and evaluation questions. Unit 1, "Introduction to the School Bus Driver Training Program," focuses on basic course objectives and…

An experimental study on real time bus arrival time prediction with GPS data

DOT National Transportation Integrated Search

2001-01-01

Bus headway in a rural area is usually much larger than that in an urban area. Providing real-time bus : arrival information could make the public transit system more user-friendly and thus enhance its : competitiveness among various transportation m...

An experimental study on real time bus arrival time prediction with GPS data

DOT National Transportation Integrated Search

1999-01-01

Bus headway in a rural area usually is much larger than that in an urban area. Providing real-time bus arrival information could make the public transit system more user-friendly and thus enhance its competitiveness among various transportation modes...

Planning criteria for express bus-fringe parking operations : volume I of express bus-fringe parking planning methodology.

DOT National Transportation Integrated Search

1975-01-01

Tripmaker reactions to two recent express bus-fringe parking operations in Richmond and Norfolk-Virginia Beach Virginia are examined. This travel behavior's interpreted to establish planning and design guidelines for locating and designing fringe lot...

A qualitative analysis of bus simulator training on transit incidents : a case study in Florida.

DOT National Transportation Integrated Search

2013-06-01

The purpose of this research was to track and observe three Florida public transit agencies as they incorporated and integrated computer-based transit bus simulators into their existing bus operator training programs. In addition to the three Florida...

Optimization models for prioritizing bus stop facility investments for riders with disabilities : March 2010.

DOT National Transportation Integrated Search

2010-03-01

The Americans with Disabilities Act (ADA) of 1990 prescribes the minimum requirements for bus stop accessibility by riders with disabilities. Due to limited budgets, transit agencies can only select a limited number of bus stop locations for ADA impr...

Complexity analysis on public transport networks of 97 large- and medium-sized cities in China

NASA Astrophysics Data System (ADS)

Tian, Zhanwei; Zhang, Zhuo; Wang, Hongfei; Ma, Li

2018-04-01

The traffic situation in Chinese urban areas is continuing to deteriorate. To make a better planning and designing of the public transport system, it is necessary to make profound research on the structure of urban public transport networks (PTNs). We investigate 97 large- and medium-sized cities’ PTNs in China, construct three types of network models — bus stop network, bus transit network and bus line network, then analyze the structural characteristics of them. It is revealed that bus stop network is small-world and scale-free, bus transit network and bus line network are both small-world. Betweenness centrality of each city’s PTN shows similar distribution pattern, although these networks’ size is various. When classifying cities according to the characteristics of PTNs or economic development level, the results are similar. It means that the development of cities’ economy and transport network has a strong correlation, PTN expands in a certain model with the development of economy.

1393 Ring Bus at JPL: Description and Status

NASA Technical Reports Server (NTRS)

Wysocky, Terry R.

2007-01-01

Completed Ring Bus IC V&V Phase - Ring Bus Test Plan Completed for SIM Project - Applicable to Other Projects Implemented a Avionics Bus Based upon the IEEE 1393 Standard - Excellent Starting Point for a General Purpose High-Speed Spacecraft Bus - Designed to Meet SIM Requirements for - Real-time deterministic, distributed systems. - Control system requirements - Fault detection and recovery Other JPL Projects Considering Implementation F'light Software Ring Bus Driver Module Began in 2006, Continues Participating in Standard Revision. Search for Earth-like planets orbiting nearby stars and measure the masses and orbits of the planets it finds. Survey 2000 nearby stars for planetary systems to learn whether our Solar System is unusual, or typical. Make a new catalog of star position 100 times more accurate than current measurements. Learn how our galaxy formed and will evolve by studying the dynamics of its stars. Critically test models of exactly how stars shine, including exotic objects like black holes, neutron stars and white dwarfs.

Potential Influence of Metro on Bus: A Case Study

NASA Astrophysics Data System (ADS)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-03-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare-difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

Potential Influence of Metro on Bus: A Case Study

NASA Astrophysics Data System (ADS)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-06-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare- difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

A robust H∞ control-based hierarchical mode transition control system for plug-in hybrid electric vehicle

NASA Astrophysics Data System (ADS)

Yang, Chao; Jiao, Xiaohong; Li, Liang; Zhang, Yuanbo; Chen, Zheng

2018-01-01

To realize a fast and smooth operating mode transition process from electric driving mode to engine-on driving mode, this paper presents a novel robust hierarchical mode transition control method for a plug-in hybrid electric bus (PHEB) with pre-transmission parallel hybrid powertrain. Firstly, the mode transition process is divided into five stages to clearly describe the powertrain dynamics. Based on the dynamics models of powertrain and clutch actuating mechanism, a hierarchical control structure including two robust H∞ controllers in both upper layer and lower layer is proposed. In upper layer, the demand clutch torque can be calculated by a robust H∞controller considering the clutch engaging time and the vehicle jerk. While in lower layer a robust tracking controller with L2-gain is designed to perform the accurate position tracking control, especially when the parameters uncertainties and external disturbance occur in the clutch actuating mechanism. Simulation and hardware-in-the-loop (HIL) test are carried out in a traditional driving condition of PHEB. Results show that the proposed hierarchical control approach can obtain the good control performance: mode transition time is greatly reduced with the acceptable jerk. Meanwhile, the designed control system shows the obvious robustness with the uncertain parameters and disturbance. Therefore, the proposed approach may offer a theoretical reference for the actual vehicle controller.

Road traffic accident among motor vehicle drivers in selected high ways.

PubMed

Ahmed, M; Khanom, K; Shampa, R M; Bari, M H

2004-07-01

To assess the knowledge of the motor vehicle driver about the causes of road traffic accidents. This cross sectional study was conducted among the 107 motor vehicle drivers of selected Bus & Truck terminal & taxi stands of Dhaka city. The study was carried out during April to June 2002 at the Department of Health Promotion & Health Education of NIPSOM. The study showed about 55.1% learned driving from a friend. Out of 107 respondent 20.6% showed very high speed is one of the reason for road traffic accident.39.3% claimed for poor maintenance of roads. Regarding engine/vehicle defect 46.7% said head light defect. Increased earning is one of the reasons of very fast driving 35.5% respondent opined. These may be the reason of accident proneness of the society along with factor like family pressure, job dissatisfaction etc. Majority of the driver who took part in this study used light vehicle 54.2% and the rest 30.8% were heavy and 15% like medium light vehicle. Most of the respondent 67.3% was working as professional over for 3-6 years. 41.1% for 3 and 26.2% for 6 years. There were significant relationship (p < 0.002) between very fast driving and defective road and also engine defect were highly significant association (p < 0.005) with road traffic accident It is revealed that formal education, driving license through Bangladesh road traffic authority without unnecessary botheration, proper implementation of traffic law, training of drivers and increase level of public awareness through mass communication could reduce the road traffic accident

Development of bus-stop time models in dense urban areas : a case study in Washington DC.

DOT National Transportation Integrated Search

2015-08-01

Bus transit reliability depends on several factors including the route of travel, traffic conditions, time of day, and conditions at : the bus stops along the route. The number of passengers alighting or boarding, fare payment method, dwell time (DT)...

Cops, cameras, and enclosures : a synthesis of the effectiveness of methods to provide enhanced security for bus operators

DOT National Transportation Integrated Search

2001-05-31

The safety of operators and passengers is a primary concern of transit systems and has become an increasingly important issue to transit bus operators themselves. Many transit agencies have experienced incidents of assaults against their bus operator...

Fuel Cell Hybrid Bus Lands at Hickam AFB

DOT National Transportation Integrated Search

2004-09-22

A FUEL CELL HYBRID ELECTRIC BUS was unveiled at Honolulus Hickam Air Force Base (Hickam AFB) in February 2004, becoming the first fuel cell vehicle in Hawaii and the first in the U.S. Air Force. The 30-foot flight crew shuttle bus will undergo 1 y...

Overview of drug and alcohol use among large truck and bus drivers, 2011–13.

DOT National Transportation Integrated Search

2016-12-01

This report provides a broad overview of drug and alcohol usage among large truck and bus drivers for 201113. Data sources for the overview are: testing results from motor carrier drug testing programs, roadside inspections on large trucks and bus...

Missouri Minimum Standards for School Buses

ERIC Educational Resources Information Center

Nicastro, Chris L.

2008-01-01

The revised minimum standards for school bus chassis and school bus bodies have been prepared in conformity with the Revised Statutes of Missouri (RSMo) for school bus transportation. The standards recommended by the 2005 National Conference on School Transportation and the Federal Motor Vehicle Safety Standards (FMVSS) promulgated by the U. S.…

A study of headway maintenance for bus routes : causes and effects of "bus bunching" in extensive and congested service areas.

DOT National Transportation Integrated Search

2012-07-01

A healthy and efficient public transit system is indispensable to reduce congestion, emissions, energy consumption, and car : dependency in urban areas. The objective of this research is to 1) develop methods to evaluate and visualize bus service rel...

School Bus Driver Instructional Program. Instructor's Guide.

ERIC Educational Resources Information Center

Department of Transportation, Washington, DC. National Highway Safety Bureau.

A standardized and comprehensive school bus driver instructional program has been developed under contract with the Federal Government. The course has been organized to provide in one package a program for developing the minimum skills and knowledge needed by the school bus driver instructor, as well as those supplemental skills and knowledge…

77 FR 71865 - Over-the-Road Bus Accessibility Grant Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-04

... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Over-the-Road Bus Accessibility Grant... selection of projects to be funded under Fiscal Year (FY) 2012 appropriations for the Over-the-Road Bus...-road buses to help finance the incremental capital and training costs of complying with DOT's over-the...

77 FR 5295 - Over-the-Road Bus Accessibility Program Announcement of Project Selections

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-02

... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Over-the-Road Bus Accessibility...-Road Bus (OTRB) Accessibility Program, authorized by Section 3038 of the Transportation Equity Act for... of over-the-road buses to help finance the incremental capital and training costs of complying with...

46 CFR 112.05-3 - Main-emergency bus-tie.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS General § 112.05-3 Main-emergency bus-tie. Each bus-tie between a main switchboard... other source of electric power, except for interlock systems for momentary transfer of loads; and (c) If...

46 CFR 112.05-3 - Main-emergency bus-tie.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS General § 112.05-3 Main-emergency bus-tie. Each bus-tie between a main switchboard... other source of electric power, except for interlock systems for momentary transfer of loads; and (c) If...

46 CFR 112.05-3 - Main-emergency bus-tie.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS General § 112.05-3 Main-emergency bus-tie. Each bus-tie between a main switchboard... other source of electric power, except for interlock systems for momentary transfer of loads; and (c) If...

46 CFR 112.05-3 - Main-emergency bus-tie.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS General § 112.05-3 Main-emergency bus-tie. Each bus-tie between a main switchboard... other source of electric power, except for interlock systems for momentary transfer of loads; and (c) If...

32 CFR 935.138 - Motor bus operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

32 CFR 935.138 - Motor bus operation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

Deadly Lessons.

ERIC Educational Resources Information Center

Vail, Kathleen

1996-01-01

In Fox River Grove, Illinois, 7 teenagers were killed the morning of October 25, 1995, when a 620-ton commuter train crashed into the rear end of their school bus. School, transportation, and safety officials have focused on three areas: train crossings and signals, bus-driver training, and school-bus construction. Lists 10 vital lessons for…

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

49 CFR 605.14 - Agreement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Agreement. 605.14 Section 605.14 Transportation... TRANSPORTATION SCHOOL BUS OPERATIONS School Bus Agreements § 605.14 Agreement. Except as provided in § 605.11 no... entered into a written agreement that the applicant will not engage in school bus operations exclusively...

Providing Increased Transit Capacity During Peak Periods : Examination of Two Techniques

DOT National Transportation Integrated Search

1975-02-01

It is shown that reduction of bus route lengths increases the number of round trips per bus possible in a given time period. For bus routes accessed mainly by auto, it is shown that significant savings in energy due to reduced auto miles travelled ar...

Transit vehicle-to-infrastructure (V2I) applications : near term research and development. Transit bus-pedestrian/cyclist crossing safety application : operational concept.

DOT National Transportation Integrated Search

2013-11-01

This document serves as an Operational Concept for the Transit Bus-Pedestrian/Cyclist Crossing Safety application. The purpose of this document is to provide an operational description of how the Transit Bus-Pedestrian/Cyclist Crossing Safety W...

49 CFR 571.221 - Standard No. 221, School bus body joint strength.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Standard No. 221, School bus body joint strength. 571.221 Section 571.221 Transportation Other Regulations Relating to Transportation (Continued... STANDARDS Federal Motor Vehicle Safety Standards § 571.221 Standard No. 221, School bus body joint strength...

Oregon Pupil Transportation Manual. Revised Regulations and Responsibilities.

ERIC Educational Resources Information Center

Oregon State Dept. of Education, Salem.

Designed for use by Oregon school bus drivers and administrators, this manual answers common questions about school bus transportation in Oregon, including those about the laws governing pupil transportation, the regulations governing pupil transportation administration, and the laws on school bus operation. A chapter of advisory materials covers…

California's Bus Driver's Training Course. Instructor's Manual.

ERIC Educational Resources Information Center

California State Dept. of Education, Sacramento.

This instructor's manual was designed to help graduates of the California Bus Driver Instructor Course provide effective instruction to school bus driver trainees. It contains enough material for 20-30 hours of classroom training. The information is organized in 12 instructional units that cover the following topics: introduction to the course;…

Updating the school bus standard vehicle for load rating Alabama bridges.

DOT National Transportation Integrated Search

2010-06-01

The objective of this project is to identify a representative school bus (weight and axle spacing) for load rating highway bridges. The ALDOT Bridge Rating and Load Test Section currently uses a 12.5-ton school bus (four tons on the front axle and 8....

Recommendations for yield-to-bus traffic control devices and bus pullout bays design characteristics.

DOT National Transportation Integrated Search

2013-04-01

Traffic control devices such as roadside signs and pavement markings are used to promote highway safety and efficiency for all road users. A bus pullout bay is a special geometric roadway feature that allows transit buses to stop outside the travel l...

Shared-use bus priority lanes on city streets : case studies in design and management [research brief].

DOT National Transportation Integrated Search

2012-04-01

This study examines the design and operations of bus lanes in major congested urban centers. It focuses on shared-use bus lanes that operate in mixed traffic conditions. : Study Methods : The key questions addressed are: : 1. How do the many public a...

49 CFR 571.221 - Standard No. 221, School bus body joint strength.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 221, School bus body joint strength. 571.221 Section 571.221 Transportation Other Regulations Relating to Transportation (Continued... STANDARDS Federal Motor Vehicle Safety Standards § 571.221 Standard No. 221, School bus body joint strength...

Highway Accident Summary Report: Bus Collision With Pedestrians, Normandy, Missouri, June 11, 1997

DOT National Transportation Integrated Search

1998-02-19

On June 11, 1997, a transit bus collided with seven pedestrians at a "park and ride" transit facility in Normandy, Missouri. The bus was being operated by a driver trainee who had just completed a routine stop at the station. After allowing the passe...

Bus--carpool FWY lanes in San Francisco area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newman, L.

1976-11-01

The California Department of Transportation is studying ways to increase the use of the urban freeway systems that will accommodate the maximum number of people with the least delay and the maximum possible safety in a cost-effective way. This paper describes operational features of four different projects under way, namely: a contraflow bus lane; a part-time bus lane in the same direction and unseparated from normal traffic; a bus-carpool lane also in the same direction and unseparated from normal traffic; and a preferential access to a metered freeway. (MCW)

Electronic inverter assembly with an integral snubber capacitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Brij N.; Schmit, Christopher J.

A coaxial bus connector has a first end and a second end opposite the first end. The first end has a first positive terminal and a first negative terminal coupled to a primary direct current bus of a primary inverter. The second end has a second positive terminal and a second negative terminal coupled to the secondary direct current bus of a secondary inverter, wherein the coaxial bus connector comprises a dielectric material between a center conductor and a coaxial sleeve to form a snubber capacitor to absorb electrical energy or to absorb voltage spikes.

Applying Unmanned Ground Vehicle Technologies To Unmanned Surface Vehicles

DTIC Science & Technology

2005-01-01

PCI or ISA bus interface • 7 UARTs • 3 USB ports • CAN bus • I2C Bus • 1 RS232 Serial Port • Two 12-bit D-A output • Two 8-bit D-A...two of the seven UARTs and the CAN bus interface. It is also used to preprocess some sensor data before sending it to the FPGA. The daughterboard...modification of the Kalman Filter and PID parameters for use in a marine environment. 2.2.1 Architecture The Small Robot Technology ( SMART ) software

Single Axis Attitude Control and DC Bus Regulation with Two Flywheels

NASA Technical Reports Server (NTRS)

Kascak, Peter E.; Jansen, Ralph H.; Kenny, Barbara; Dever, Timothy P.

2002-01-01

A computer simulation of a flywheel energy storage single axis attitude control system is described. The simulation models hardware which will be experimentally tested in the future. This hardware consists of two counter rotating flywheels mounted to an air table. The air table allows one axis of rotational motion. An inertia DC bus coordinator is set forth that allows the two control problems, bus regulation and attitude control, to be separated. Simulation results are presented with a previously derived flywheel bus regulator and a simple PID attitude controller.

Electrical contact structures for solid oxide electrolyte fuel cell

DOEpatents

Isenberg, Arnold O.

1984-01-01

An improved electrical output connection means is provided for a high temperature solid oxide electrolyte type fuel cell generator. The electrical connection of the fuel cell electrodes to the electrical output bus, which is brought through the generator housing to be connected to an electrical load line maintains a highly uniform temperature distribution. The electrical connection means includes an electrode bus which is spaced parallel to the output bus with a plurality of symmetrically spaced transversely extending conductors extending between the electrode bus and the output bus, with thermal insulation means provided about the transverse conductors between the spaced apart buses. Single or plural stages of the insulated transversely extending conductors can be provided within the high temperatures regions of the fuel cell generator to provide highly homogeneous temperature distribution over the contacting surfaces.

A voltage-controlled superconducting quantum bus

NASA Astrophysics Data System (ADS)

Casparis, Lucas; Pearson, Natalie; KringhøJ, Anders; Larsen, Thorvald; Kuemmeth, Ferdinand; Krogstrup, Peter; Nygard, Jesper; Petersson, Karl; Marcus, Charles

Superconducting qubits couple strongly to microwave photons and can therefore be coupled over long distances through a superconducting cavity acting as a quantum bus. To avoid frequency-crowding it is desirable to turn qubit coupling off while rearranging qubit frequencies. Here, we present experiments with two gatemon qubits coupled through a cavity, which can be tuned by a voltage-controlled superconducting switch. We characterize the bus tunability and demonstrate switchable qubit coupling with an on/off ratio up to 8. We find that pulsing the bus switch on nanosecond timescales results in the apparent loss of qubit coherence. Further work is needed to understand how dynamic control of the tuneable bus affects qubit operation. We acknowledge financial support from Microsoft Project Q, the Danish National Research Foundation and the US Army Research Office.

Stability improvement of wind turbine penetrated using power system stabilizer (PSS) on South Sulawesi transmission system

NASA Astrophysics Data System (ADS)

Siswanto, Agus; Gunadin, Indar Chaerah; Said, Sri Mawar; Suyuti, Ansar

2018-03-01

The purpose of this research is to improve the stability of interconnection of South Sulawesi system caused by penetration new wind turbine in Sidrap area on bus 2 and in Jeniponto area on bus 34. The method used in this research was via software Power System analysis Toolbox (PSAT) under MATLAB. In this research, there are two problems that are evaluated, the stability of the system before and after penetration wind turbine into the system South Sulawesi system. From the simulation result shows that penetration of wind turbine on bus 2 Sidrap, bus 37 Jeniponto give effect oscillation on the system. The oscillation was damped by installation of Power System Stabilizer (PSS) on bus 29 area Sungguminasa, that South Sulawesi system stable according to normal condition.

Accessing memory

DOEpatents

Yoon, Doe Hyun; Muralimanohar, Naveen; Chang, Jichuan; Ranganthan, Parthasarathy

2017-09-26

A disclosed example method involves performing simultaneous data accesses on at least first and second independently selectable logical sub-ranks to access first data via a wide internal data bus in a memory device. The memory device includes a translation buffer chip, memory chips in independently selectable logical sub-ranks, a narrow external data bus to connect the translation buffer chip to a memory controller, and the wide internal data bus between the translation buffer chip and the memory chips. A data access is performed on only the first independently selectable logical sub-rank to access second data via the wide internal data bus. The example method also involves locating a first portion of the first data, a second portion of the first data, and the second data on the narrow external data bus during separate data transfers.

Unhealthy and healthy weight control behaviours among bus operators.

PubMed

Escoto, K H; French, S A

2012-03-01

Urban bus operators are an occupational group with high rates of overweight and obesity. Understanding methods bus operators use for weight control may be important; there may be increased risk for these workers to engage in less healthy weight management behaviours due to stressful working conditions. To examine the prevalence of unhealthy and healthy weight control behaviours used by bus operators and examine associations between use of unhealthy weight control behaviours and work-related and sociodemographic variables. Bus operators from four different transit garages were invited to complete a self-administered survey; height and weight were measured by research staff. Unhealthy and healthy weight control behaviours, work hours, work schedule and social support were measured with self-report items on the employee survey. Logistic regression analysis was conducted to estimate associations. Nearly 60% of bus operators endorsed at least one unhealthy method; over 50% reported skipping meals, 30% fasted and 10% reported taking diet pills in the past year. Bus operator gender, race, body mass index status and hours worked per week showed significant associations with using at least one unhealthy weight control behaviour. Worksite interventions should emphasize the benefit of healthy eating and physical activity but should also address the use of less healthy methods for weight control for individuals employed in transportation occupations.

Design of limited-stop service based on the degree of unbalance of passenger demand

PubMed Central

2018-01-01

This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands. PMID:29505585

Design of limited-stop service based on the degree of unbalance of passenger demand.

PubMed

Zhang, Hu; Zhao, Shuzhi; Liu, Huasheng; Liang, Shidong

2018-01-01

This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands.

A free ride? An analysis of the association of casino bus tours and problem gambling among older adults.

PubMed

van der Maas, Mark; Mann, Robert E; Matheson, Flora I; Turner, Nigel E; Hamilton, Hayley A; McCready, John

2017-12-01

Little research has examined the relationship between incentives used by gambling venues to attract customers and the experience of gambling-related harm. Organized and subsidized bus tours are a common example of such incentives. The aim of this study was to examine whether bus-tour patronage was associated with increased odds of problem gambling among older adults. This study also compared rates of bus-tour use by socio-demographic characteristics and gambling behaviours. Pearson's χ 2 tests and Mann-Whitney U-tests were applied for bivariate analyses. Multivariate generalized mixed-effects regression modelling was used to examine the relationship between bus-tour patronage and problem gambling while controlling for possible confounding factors. Seven gambling venues located in Central and Southwestern Ontario, Canada. A total of 1978 gambling venue patrons over the age of 55 years. Problem gambling as indicated by the Problem Gambling Severity Index, bus-tour patronage in the 12 months prior to the survey, spending per gambling visit and past-month slot machine participation. Regression analyses showed that bus-tour patronage was associated with higher odds of problem gambling [odds ratio (OR) = 1.71, confidence interval (CI) = 1.06, 2.76] after controlling for several demographic characteristics, type of gambling and gambling expenditures. Bivariate analyses showed past-year bus-tour patronage was associated with more frequent slot machine play (χ 2 = 48.16, P < 0.001), more past-year gambling venue visits (P < 0.001) and lower spending on gambling per casino visit (P < 0.001). Compared with non-patrons, bus tour patrons were more likely to be female (χ 2 = 21.92, P < 0.001), born outside Canada (χ 2 = 113.18, P < 0.001), above the age of 75 (χ 2 = 24.02, P < 0.001) and retired (χ 2 = 16.60, P < 0.001). When adjusting for potential confounders among older adults, using bus tours to access Canadian gambling venues is associated with increased risk of problem gambling. Bus-tour patrons are more likely to be female, born outside Canada and above the age of 75 years. © 2017 The Authors. Addiction published by John Wiley & Sons Ltd on behalf of Society for the Study of Addiction.

Bedside Ultrasonography as an Adjunct to Routine Evaluation of Acute Appendicitis in the Emergency Department

PubMed Central

Lam, Samuel H.F.; Grippo, Anthony; Kerwin, Chistopher; Konicki, P. John; Goodwine, Diana; Lambert, Michael J.

2014-01-01

Introduction Appendicitis is a common condition presenting to the emergency department (ED). Increasingly emergency physicians (EP) are using bedside ultrasound (BUS) as an adjunct diagnostic tool. Our objective is to investigate the test characteristics of BUS for the diagnosis of appendicitis and identify components of routine ED workup and BUS associated with the presence of appendicitis. Methods Patients four years of age and older presenting to the ED with suspected appendicitis were eligible for enrollment. After informed consent was obtained, BUS was performed on the subjects by trained EPs who had undergone a minimum of one-hour didactic training on the use of BUS to diagnose appendicitis. They then recorded elements of clinical history, physical examination, white blood cell count (WBC) with polymophonuclear percentage (PMN), and BUS findings on a data form. We ascertained subject outcomes by a combination of medical record review and telephone follow-up. Results A total of 125 subjects consented for the study, and 116 had adequate image data for final analysis. Prevalence of appendicitis was 40%. Mean age of the subjects was 20.2 years, and 51% were male. BUS was 100% sensitive (95% CI 87–100%) and 32% specific (95% CI 14–57%) for detection of appendicitis, with a positive predictive value of 72% (95% CI 56–84%), and a negative predictive value of 100% (95% CI 52–100%). Assuming all non-diagnostic studies were negative would yield a sensitivity of 72% and specificity of 81%. Subjects with appendicitis had a significantly higher occurrence of anorexia, nausea, vomiting, and a higher WBC and PMN count when compared to those without appendicitis. Their BUS studies were significantly more likely to result in visualization of the appendix, appendix diameter >6mm, appendix wall thickness >2mm, periappendiceal fluid, visualization of the appendix tip, and sonographic Mcburney’s sign (p<0.05). In subjects with diagnostic BUS studies, WBC, PMN, visualization of appendix, appendix diameter >6mm, appendix wall thickness >2mm, periappendiceal fluid were found to be predictors of appendicitis on logistic regression. Conclusion BUS is moderately useful for appendicitis diagnosis. We also identified several components in routine ED workup and BUS that are associated with appendicitis generating hypothesis for future studies. PMID:25493122

Application of new electro-optic technology to Space Station Freedom data management system

NASA Technical Reports Server (NTRS)

Husbands, C. R.; Girard, M. M.

1993-01-01

A low risk design methodology to permit the local bus structures to support increased data carrying capacities and to speed messages and data flow between nodes or stations on the Space Station Freedom Data Management System in anticipation of growing requirements was evaluated and recommended. The recommended design employs a collateral fiber optic technique that follows a NATO avionic standard that is developed, tested, and available. Application of this process will permit a potential 25 fold increase in data transfer performance on the local wire bus network with a fiber optic network, maintaining the functionality of the low-speed bus and supporting all of the redundant transmission and fault detection capabilities designed into the existing system. The application of wavelength division multiplexing (WDM) technology to both the local data bus and global data bus segments of the Data Management System to support anticipated additional highspeed data transmission requirements was also examined. Techniques were examined to provide a dual wavelength implementation of the fiber optic collateral networks. This dual wavelength implementation would permit each local bus to support two simultaneous high-speed transfers on the same fiber optic bus structure and operate within the limits of the existing protocol standard. A second WDM study examined the use of spectral sliced technology to provide a fourfold increase in the Fiber Distributed Data Interface (FDDI) global bus networks without requiring modifications to the existing installed cable plant. Computer simulations presented indicated that this data rate improvement can be achieved with commercially available optical components.

Architecture, Voltage, and Components for a Turboelectric Distributed Propulsion Electric Grid (AVC-TeDP)

NASA Technical Reports Server (NTRS)

Gemin, Paul; Kupiszewski, Tom; Radun, Arthur; Pan, Yan; Lai, Rixin; Zhang, Di; Wang, Ruxi; Wu, Xinhui; Jiang, Yan; Galioto, Steve;

2013 Missouri Minimum Standards for School Buses

ERIC Educational Resources Information Center

Nicastro, Chris L.

2012-01-01

The revised minimum standards for school bus chassis and school bus bodies have been prepared in conformity with the Revised Statutes of Missouri (RSMo) for school bus transportation. The standards recommended by the 2010 National Conference on School Transportation and the Federal Motor Vehicle Safety Standards (FMVSS) promulgated by the U. S.…

An evaluation of the effect of level of service and cost on demand for intercity bus travel : final report.

DOT National Transportation Integrated Search

1980-01-01

This report describes an evaluation of the effect on intercity bus ridership of changes in frequency of service and cost. The study was based on a comparison of travel between 19 selected cities in Virginia served by air, bus, or rail. These modes we...

49 CFR 1331.5 - Additional standards for retaining antitrust immunity by passenger bus industry rate bureaus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... immunity by passenger bus industry rate bureaus. 1331.5 Section 1331.5 Transportation Other Regulations... standards for retaining antitrust immunity by passenger bus industry rate bureaus. (a) Rate bureaus must... of immunity for that activity. (b) The bureaus are required to maintain detailed minutes of all...

49 CFR 1331.5 - Additional standards for retaining antitrust immunity by passenger bus industry rate bureaus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... immunity by passenger bus industry rate bureaus. 1331.5 Section 1331.5 Transportation Other Regulations... standards for retaining antitrust immunity by passenger bus industry rate bureaus. (a) Rate bureaus must... of immunity for that activity. (b) The bureaus are required to maintain detailed minutes of all...

49 CFR 1331.5 - Additional standards for retaining antitrust immunity by passenger bus industry rate bureaus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... immunity by passenger bus industry rate bureaus. 1331.5 Section 1331.5 Transportation Other Regulations... standards for retaining antitrust immunity by passenger bus industry rate bureaus. (a) Rate bureaus must... of immunity for that activity. (b) The bureaus are required to maintain detailed minutes of all...

49 CFR 1331.5 - Additional standards for retaining antitrust immunity by passenger bus industry rate bureaus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... immunity by passenger bus industry rate bureaus. 1331.5 Section 1331.5 Transportation Other Regulations... standards for retaining antitrust immunity by passenger bus industry rate bureaus. (a) Rate bureaus must... of immunity for that activity. (b) The bureaus are required to maintain detailed minutes of all...

49 CFR 1331.5 - Additional standards for retaining antitrust immunity by passenger bus industry rate bureaus.

Code of Federal Regulations, 2014 CFR

2014-10-01

... immunity by passenger bus industry rate bureaus. 1331.5 Section 1331.5 Transportation Other Regulations... standards for retaining antitrust immunity by passenger bus industry rate bureaus. (a) Rate bureaus must... of immunity for that activity. (b) The bureaus are required to maintain detailed minutes of all...

40 CFR 85.1407 - Notification of intent to certify.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1407... certifier that use of its certified equipment will not cause a substantial increase to urban bus engine... § 85.1403(b) for all affected urban bus operators as specified in § 85.1401, the notification shall...

40 CFR 85.1407 - Notification of intent to certify.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1407... certifier that use of its certified equipment will not cause a substantial increase to urban bus engine... § 85.1403(b) for all affected urban bus operators as specified in § 85.1401, the notification shall...

40 CFR 85.1407 - Notification of intent to certify.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1407... certifier that use of its certified equipment will not cause a substantial increase to urban bus engine... § 85.1403(b) for all affected urban bus operators as specified in § 85.1401, the notification shall...

40 CFR 85.1407 - Notification of intent to certify.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1407... certifier that use of its certified equipment will not cause a substantial increase to urban bus engine... § 85.1403(b) for all affected urban bus operators as specified in § 85.1401, the notification shall...

Design Report for Isolated RS-485 Bus Node

DTIC Science & Technology

2016-07-01

controlled wired RS-485 network. The Android-based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in...Android-based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in the system. The Android device