B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA)

DTIC Science & Technology

2013-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-468 B61 Mod 12 Life Extension Program Tailkit Assembly ( B61 Mod 12 LEP TKA...REPORT TYPE 3. DATES COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE B61 Mod 12 Life Extension Program Tailkit Assembly ( B61 Mod 12 LEP...REPORT unclassified b. ABSTRACT unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 B61 Mod 12

Initial results from divertor heat-flux instrumentation on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Labombard, B.; Brunner, D.; Payne, J.; Reinke, M.; Terry, J. L.; Hughes, J. W.; Lipschultz, B.; Whyte, D.

2009-11-01

Physics-based plasma transport models that can accurately simulate the heat-flux power widths observed in the tokamak boundary are lacking at the present time. Yet this quantity is of fundamental importance for ITER and most critically important for DEMO, a reactor similar to ITER but with ˜4 times the power exhaust. In order to improve our understanding, C-Mod, DIII-D and NSTX will aim experiments in FY10 towards characterizing the divertor ``footprint'' and its connection to conditions ``upstream'' in the boundary and core plasmas [2]. Standard IR-based heat-flux measurements are particularly difficult in C-Mod, due to its vertical-oriented divertor targets. To overcome this, a suite of embedded heat-flux sensor probes (tile thermocouples, calorimeters, surface thermocouples) combined with IR thermography was installed during the FY09 opening, along with a new divertor bolometer system. This paper will report on initial experiments aimed at unfolding the heat-flux dependencies on plasma operating conditions. [2] a proposed US DoE Joint Facilities Milestone.

Scanning retarding field analyzer for plasma profile measurements in the boundary of the Alcator C-Mod tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brunner, D.; LaBombard, B.; Ochoukov, R.

2013-03-15

A new Retarding Field Analyzer (RFA) head has been created for the outer-midplane scanning probe system on the Alcator C-Mod tokamak. The new probe head contains back-to-back retarding field analyzers aligned with the local magnetic field. One faces 'upstream' into the field-aligned plasma flow and the other faces 'downstream' away from the flow. The RFA was created primarily to benchmark ion temperature measurements of an ion sensitive probe; it may also be used to interrogate electrons. However, its construction is robust enough to be used to measure ion and electron temperatures up to the last-closed flux surface in C-Mod. Amore » RFA probe of identical design has been attached to the side of a limiter to explore direct changes to the boundary plasma due to lower hybrid heating and current drive. Design of the high heat flux (>100 MW/m{sup 2}) handling probe and initial results are presented.« less

Validation of the MODIS MOD21 and MOD11 land surface temperature and emissivity products in an arid area of Northwest China

NASA Astrophysics Data System (ADS)

Li, H.; Yang, Y.; Yongming, D.; Cao, B.; Qinhuo, L.

2017-12-01

Land surface temperature (LST) is a key parameter for hydrological, meteorological, climatological and environmental studies. During the past decades, many efforts have been devoted to the establishment of methodology for retrieving the LST from remote sensing data and significant progress has been achieved. Many operational LST products have been generated using different remote sensing data. MODIS LST product (MOD11) is one of the most commonly used LST products, which is produced using a generalized split-window algorithm. Many validation studies have showed that MOD11 LST product agrees well with ground measurements over vegetated and inland water surfaces, however, large negative biases of up to 5 K are present over arid regions. In addition, land surface emissivity of MOD11 are estimated by assigning fixed emissivities according to a land cover classification dataset, which may introduce large errors to the LST product due to misclassification of the land cover. Therefore, a new MODIS LSE&E product (MOD21) is developed based on the temperature emissivity separation (TES) algorithm, and the water vapor scaling (WVS) method has also been incorporated into the MODIS TES algorithm for improving the accuracy of the atmospheric correction. The MOD21 product will be released with MODIS collection 6 Tier-2 land products in 2017. Due to the MOD21 products are not available right now, the MODTES algorithm was implemented including the TES and WVS methods as detailed in the MOD21 Algorithm Theoretical Basis Document. The MOD21 and MOD11 C6 LST products are validated using ground measurements and ASTER LST products collected in an arid area of Northwest China during the Heihe Watershed Allied Telemetry Experimental Research (HiWATER) experiment. In addition, lab emissivity spectra of four sand dunes in the Northwest China are also used to validate the MOD21 and MOD11 emissivity products.

ModSAF Software Architecture Design and Overview Document

DTIC Science & Technology

1993-12-20

ADVANCED DISTRIBUTED SIMULATIONTECHNOLOGY AD-A282 740 ModSAF SOFTWARE ARCHITECTURE DESIGN AND OVERVIEW DOCUMENT Ver 1.0 - 20 December 1993 D T...AND SUBTITLE 5. FUNDING NUMBERS MOdSAF SOFTWARE ARCHITECTURE DESIGN AND OVERVIEW DOCUMENT C N61339-91-D-O00, Delivery Order (0021), ModSAF (CDRL A004) 6

Current status and future prospects of Japanese national project on coated conductor development and its applications

NASA Astrophysics Data System (ADS)

Shiohara, Y.; Yoshizumi, M.; Izumi, T.; Yamada, Y.

2008-09-01

Four years of the current five-year national project since 2003 for development of coated conductors using Y-system superconductors have passed and lots of remarkable results have been achieved. In this paper, the current status and the future prospect of this project are reviewed. The current national project comprises several groups of national laboratories, universities and private companies. The group of high performance tape development, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting tapes on the PLD-CeO 2/IBAD-GZO buffered substrates. The high product of Ic and L equal to 112,166 A m was achieved in the 368 m-304.8 A GdBCO tape whose Ic value is mostly above 350 A/cm-w. The performance under the magnetic fields was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO 2. About 61 m long GdBCO tape with ZrO 2 doping showed a high Ic value of 220 A at self field and 30 A at 3 T. On the other hand, the other group focusing on the low production cost has worked on processes of TFA-MOD and MOCVD, etc. The extremely high Ic value of 735 A/cm-w was attained in the TFA-MOD films on PLD-CeO 2/IBAD-GZO/Hastelloy C276 substrate by means of using the effect of Ba-poor nominal composition. In the efforts for long tape production, 200 m long tapes with high Ic values of 200 A/cm-w and 205 A/cm-w were obtained by MOD-YBCO/PLD-CeO 2/IBAD-GZO/Hastelloy C276 and PLD-HoBCO on buffered NiW substrate, respectively. The Ic × L value of the MOD-derived tape was 40,000 A m, which is the highest value in the world by the MOD process. Based on the above achievements on the coated conductor process development, two new additional goals were set in the project. One is the development for the extremely low cost tape and another is the development of the basic technologies for making the electric power devices including cables, transformers, motors, current-limiters and cryocoolers. Some of the new themes already revealed the marvellous results such as 15 kW motor, low AC loss coils, low AC loss cables, etc.

Fracture strength of endodontically treated molars transfixed horizontally by a fiber glass post.

PubMed

Beltrão, Maria Cecilia Gomes; Spohr, Ana Maria; Oshima, Hugo Mitsuo Silva; Mota, Eduardo Gonçalves; Burnett, Luiz Henrique

2009-02-01

To assess the effect of a horizontally transfixed fiber glass post placed between buccal and palatal surfaces, on the fracture strength of endodontically treated molar teeth with MOD cavities, either restored with resin-based composite, or not. 75 sound maxillary human third molars were extracted, embedded in acrylic resin blocks and randomly assigned to five groups (n=15). Group A (sound teeth), (control) and Groups B, C, D and E, which were subjected to the following procedures after endodontic treatment: GB--(MOD+Endo), GC--(MOD+Endo+Post), GD--MOD and composite restoration (MOD+Endo+CR), GE--(MOD+Endo+Post+CR). The specimens were stored in distilled water at 37 degrees C for 24 hours. Later, a compressive force was applied by means of a universal testing machine at 1 mm/minute speed, parallel to the long axis of the teeth until fracture occurred. The means of the results (N) followed by the same letter represent no statistical difference by ANOVA and Tukey (P<0.05): GA = 4289.8 (+/- 1128.9)a, GB = 549.6 (+/- 120.7)b, GC = 1474.8 (+/- 338.1)c, GD = 1224.7 (+/- 236.0)c, GE = 2645.4 (+/- 675.1)d. In the analysis of qualitative variables, there was a tendency to cusp fracture in all groups except for Group C. The fiber glass post transfixed horizontally in a MOD cavity significantly increased the fracture resistance of the teeth restored with resin composite.

Disruption Warning Database Development and Exploratory Machine Learning Studies on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Montes, Kevin; Rea, Cristina; Granetz, Robert

2017-10-01

A database of about 1800 shots from the 2015 campaign on the Alcator C-Mod tokamak is assembled, including disruptive and non-disruptive discharges. The database consists of 40 relevant plasma parameters with data taken from 160k time slices. In order to investigate the possibility of developing a robust disruption prediction algorithm that is tokamak-independent, we focused machine learning studies on a subset of dimensionless parameters such as βp, n /nG , etc. The Random Forests machine learning algorithm provides insight on the available data set by ranking the relative importance of the input features. Its application on the C-Mod database, however, reveals that virtually no one parameter has more importance than any other, and that its classification algorithm has a low rate of successfully predicted samples, as well as poor false positive and false negative rates. Comparing the analysis of this algorithm on the C-Mod database with its application to a similar database on DIII-D, we conclude that disruption prediction may not be feasible on C-Mod. This conclusion is supported by empirical observations that most C-Mod disruptions are caused by radiative collapse due to molybdenum from the first wall, which happens on just a 1-2ms timescale. Supported by the US Dept. of Energy under DE-FC02-99ER54512 and DE-FC02-04ER54698.

Serum cytochrome c level as a prognostic indicator in patients with systemic inflammatory response syndrome.

PubMed

Adachi, Naoto; Hirota, Masahiko; Hamaguchi, Masamichi; Okamoto, Kazufumi; Watanabe, Keisuke; Endo, Fumio

2004-04-01

Apoptosis may play an important role in the development of systemic inflammatory response syndrome (SIRS) and progression to multiple organ dysfunction syndrome (MODS). To quantify the extent of apoptosis in these morbidities, we developed a sandwich ELISA system to measure serum cytochrome c (cyt-c) levels and we investigated the prognostic significance of cyt-c concentration in SIRS/MODS patients. Cyt-c concentrations in patients with SIRS (n=53) with or at risk for MODS were measured and compared with those of control subjects (n=14). Cyt-c concentrations in SIRS/MODS patients increased (0.24-210 ng/ml), whereas those in control subjects were under detection limits (0.1 ng/ml). Cyt-c concentrations in non-survivors increased significantly compared with those in survivors both on the day of admission and on the fifth hospital day. A significant positive correlation was found between cyt-c concentration and two representative organ dysfunction scores, APACHE II and multi-organ failure (MOF) score. Cyt-c concentrations increased earlier than MOF score during the exacerbation phase and rapidly decreased during the convalescence phase in a survivor, but the level continued to be high in a non-survivor. Determination of serum cyt-c concentrations may be useful to assess the severity of organ dysfunction and to predict the prognosis of SIRS/MODS patients.

Memantine in patients with Alzheimer's disease receiving donepezil: new analyses of efficacy and safety for combination therapy.

PubMed

Atri, Alireza; Molinuevo, José L; Lemming, Ole; Wirth, Yvonne; Pulte, Irena; Wilkinson, David

2013-01-01

Memantine and cholinesterase inhibitors potentially offer additional benefits in Alzheimer's disease (AD) when used together. This study assessed the efficacy and safety of combination treatment with memantine added to stable donepezil in patients with moderate to severe AD, and in a subset with moderate AD. Post hoc meta-analyses of data combined from two 24-week, randomised, double-blind, placebo-controlled trials of memantine 20 mg/day versus placebo, added to a stable cholinesterase inhibitor, were conducted. Data were included for all patients receiving donepezil 10 mg/day with Mini-Mental State Examination (MMSE) scores < 20 (n = 510). Efficacy was assessed using measures of cognition, function, and global status. Furthermore, marked clinical worsening, defined as concurrent deterioration from baseline in the three main efficacy domains, and safety, measured by treatment-emergent adverse events, were assessed. Analyses were performed for patients with moderate to severe AD (MMSE 5-19; MOD-SEV subgroup), and also for patients with moderate AD (MMSE 10-19; MOD subgroup; n = 367). At week 24, in the MOD-SEV subgroup, patients receiving memantine added to donepezil significantly outperformed those receiving placebo added to donepezil in measures of cognition (P < 0.0001), function (P = 0.02), and global status (P = 0.010), with standardised mean differences (SMDs) of 0.36, 0.21, and 0.23, respectively (all last observation carried forward). Similarly, in the MOD subgroup, significant benefits were observed for cognition (P = 0.008), function (P = 0.04) and global status (P = 0.008), with SMDs of 0.28, 0.21, and 0.28, respectively. Significantly fewer patients receiving memantine added to donepezil showed marked clinical worsening than those receiving placebo added to donepezil, in both subgroups (MOD-SEV: 8.7% versus 20.4%, P = 0.0002; MOD: 5.9% versus 15.0%, P = 0.006). The incidence of adverse events was similar between treatment groups. These results support and extend previous evidence that combination treatment with memantine added to stable donepezil in patients with moderate AD, and in those with moderate to severe AD, is associated with significant benefits in reducing 24-week decline in cognition, function and global status. Combination treatment produces substantially reduced rates of marked clinical worsening, has good safety and tolerability, and generates effect sizes that are both statistically significant and clinically meaningful.

Reflectometry measurements of turbulence in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Basse, N. P.; Lin, Y.; Irby, J.; Kramer, G. J.; Nazikian, R.

2003-10-01

An amplitude modulated (AM) reflectometer system operating in O-mode has been used for density profile and fluctuation measurements on Alcator C-Mod. This system consists of five channels, whose frequencies correspond to densities from 0.31 × 10^20 m-3 to 1.5 × 10^20 m-3. The 88 GHz channel has separate upper and lower sideband measurements of the AM waves, resulting in an increased sensitivity to fluctuations. Recently, two additional dedicated fluctuation channels have been brought into operation at 132 and 140 GHz, corresponding to densities of 2.2 × 10^20 m-3 and 2.4 × 10^20 m-3. The new channels allow observations to be made further into the pedestal region and in some cases reach the foot of the internal transport barrier. We will present spectral analysis results from selected channels during confinement transitions in Alcator C-Mod plasmas, e.g. at the L- to H-mode bifurcation. Further, correlation studies will be undertaken between the various channels to elucidate the possible existence of moving and/or overlapping turbulent structures.

Novel energy resolving x-ray pinhole camera on Alcator C-Mod.

PubMed

Pablant, N A; Delgado-Aparicio, L; Bitter, M; Brandstetter, S; Eikenberry, E; Ellis, R; Hill, K W; Hofer, P; Schneebeli, M

2012-10-01

A new energy resolving x-ray pinhole camera has been recently installed on Alcator C-Mod. This diagnostic is capable of 1D or 2D imaging with a spatial resolution of ≈1 cm, an energy resolution of ≈1 keV in the range of 3.5-15 keV and a maximum time resolution of 5 ms. A novel use of a Pilatus 2 hybrid-pixel x-ray detector [P. Kraft et al., J. Synchrotron Rad. 16, 368 (2009)] is employed in which the lower energy threshold of individual pixels is adjusted, allowing regions of a single detector to be sensitive to different x-ray energy ranges. Development of this new detector calibration technique was done as a collaboration between PPPL and Dectris Ltd. The calibration procedure is described, and the energy resolution of the detector is characterized. Initial data from this installation on Alcator C-Mod is presented. This diagnostic provides line-integrated measurements of impurity emission which can be used to determine impurity concentrations as well as the electron energy distribution.

Mod II engine performance

NASA Technical Reports Server (NTRS)

Richey, Albert E.; Huang, Shyan-Cherng

1987-01-01

The testing of a prototype of an automotive Stirling engine, the Mod II, is discussed. The Mod II is a one-piece cast block with a V-4 single-crankshaft configuration and an annular regenerator/cooler design. The initial testing of Mod II concentrated on the basic engine, with auxiliaries driven by power sources external to the engine. The performance of the engine was tested at 720 C set temperature and 820 C tube temperature. At 720 C, it is observed that the power deficiency is speed dependent and linear, with a weak pressure dependency, and at 820 C, the power deficiency is speed and pressure dependent. The effects of buoyancy and nozzle spray pattern on the heater temperature spread are investigated. The characterization of the oil pump and the operating cycle and temperature spread tests are proposed for further evaluation of the engine.

Precocious Metamorphosis in the Juvenile Hormone–Deficient Mutant of the Silkworm, Bombyx mori

PubMed Central

Daimon, Takaaki; Kozaki, Toshinori; Niwa, Ryusuke; Kobayashi, Isao; Furuta, Kenjiro; Namiki, Toshiki; Uchino, Keiro; Banno, Yutaka; Katsuma, Susumu; Tamura, Toshiki; Mita, Kazuei; Sezutsu, Hideki; Nakayama, Masayoshi; Itoyama, Kyo; Shimada, Toru; Shinoda, Tetsuro

2012-01-01

Insect molting and metamorphosis are intricately governed by two hormones, ecdysteroids and juvenile hormones (JHs). JHs prevent precocious metamorphosis and allow the larva to undergo multiple rounds of molting until it attains the proper size for metamorphosis. In the silkworm, Bombyx mori, several “moltinism” mutations have been identified that exhibit variations in the number of larval molts; however, none of them have been characterized molecularly. Here we report the identification and characterization of the gene responsible for the dimolting (mod) mutant that undergoes precocious metamorphosis with fewer larval–larval molts. We show that the mod mutation results in complete loss of JHs in the larval hemolymph and that the mutant phenotype can be rescued by topical application of a JH analog. We performed positional cloning of mod and found a null mutation in the cytochrome P450 gene CYP15C1 in the mod allele. We also demonstrated that CYP15C1 is specifically expressed in the corpus allatum, an endocrine organ that synthesizes and secretes JHs. Furthermore, a biochemical experiment showed that CYP15C1 epoxidizes farnesoic acid to JH acid in a highly stereospecific manner. Precocious metamorphosis of mod larvae was rescued when the wild-type allele of CYP15C1 was expressed in transgenic mod larvae using the GAL4/UAS system. Our data therefore reveal that CYP15C1 is the gene responsible for the mod mutation and is essential for JH biosynthesis. Remarkably, precocious larval–pupal transition in mod larvae does not occur in the first or second instar, suggesting that authentic epoxidized JHs are not essential in very young larvae of B. mori. Our identification of a JH–deficient mutant in this model insect will lead to a greater understanding of the molecular basis of the hormonal control of development and metamorphosis. PMID:22412378

Aeroacoustic Codes For Rotor Harmonic and BVI Noise--CAMRAD.Mod1/HIRES

NASA Technical Reports Server (NTRS)

Brooks, Thomas F.; Boyd, D. Douglas, Jr.; Burley, Casey L.; Jolly, J. Ralph, Jr.

1996-01-01

This paper presents a status of non-CFD aeroacoustic codes at NASA Langley Research Center for the prediction of helicopter harmonic and Blade-Vortex Interaction (BVI) noise. The prediction approach incorporates three primary components: CAMRAD.Mod1 - a substantially modified version of the performance/trim/wake code CAMRAD; HIRES - a high resolution blade loads post-processor; and WOPWOP - an acoustic code. The functional capabilities and physical modeling in CAMRAD.Mod1/HIRES will be summarized and illustrated. A new multi-core roll-up wake modeling approach is introduced and validated. Predictions of rotor wake and radiated noise are compared with to the results of the HART program, a model BO-105 windtunnel test at the DNW in Europe. Additional comparisons are made to results from a DNW test of a contemporary design four-bladed rotor, as well as from a Langley test of a single proprotor (tiltrotor) three-bladed model configuration. Because the method is shown to help eliminate the necessity of guesswork in setting code parameters between different rotor configurations, it should prove useful as a rotor noise design tool.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, K W; Delgado-Aprico, L; Johnson, D

Imaging XCS arrays are being developed as a US-ITER activity for Doppler measurement of Ti and v profiles of impurities (W, Kr, Fe) with ~7 cm (a/30) and 10-100 ms resolution in ITER. The imaging XCS, modeled after a PPPL-MIT instrument on Alcator C-Mod, uses a spherically bent crystal and 2d x-ray detectors to achieve high spectral resolving power (E/dE>6000) horizontally and spatial imaging vertically. Two arrays will measure Ti and both poloidal and toroidal rotation velocity profiles. Measurement of many spatial chords permits tomographic inversion for inference of local parameters. The instrument design, predictions of performance, and results frommore » C-Mod will be presented.« less

Comparison and Evaluation of Annual NDVI Time Series in China Derived from the NOAA AVHRR LTDR and Terra MODIS MOD13C1 Products

PubMed Central

Guo, Xiaoyi; Zhang, Hongyan; Wu, Zhengfang; Zhao, Jianjun; Zhang, Zhengxiang

2017-01-01

Time series of Normalized Difference Vegetation Index (NDVI) derived from multiple satellite sensors are crucial data to study vegetation dynamics. The Land Long Term Data Record Version 4 (LTDR V4) NDVI dataset was recently released at a 0.05 × 0.05° spatial resolution and daily temporal resolution. In this study, annual NDVI time series that are composited by the LTDR V4 and Moderate Resolution Imaging Spectroradiometer (MODIS) NDVI datasets (MOD13C1) are compared and evaluated for the period from 2001 to 2014 in China. The spatial patterns of the NDVI generally match between the LTDR V4 and MOD13C1 datasets. The transitional zone between high and low NDVI values generally matches the boundary of semi-arid and sub-humid regions. A significant and high coefficient of determination is found between the two datasets according to a pixel-based correlation analysis. The spatially averaged NDVI of LTDR V4 is characterized by a much weaker positive regression slope relative to that of the spatially averaged NDVI of the MOD13C1 dataset because of changes in NOAA AVHRR sensors between 2005 and 2006. The measured NDVI values of LTDR V4 were always higher than that of MOD13C1 in western China due to the relatively lower atmospheric water vapor content in western China, and opposite observation appeared in eastern China. In total, 18.54% of the LTDR V4 NDVI pixels exhibit significant trends, whereas 35.79% of the MOD13C1 NDVI pixels show significant trends. Good agreement is observed between the significant trends of the two datasets in the Northeast Plain, Bohai Economic Rim, Loess Plateau, and Yangtze River Delta. By contrast, the datasets contrasted in northwestern desert regions and southern China. A trend analysis of the regression slope values according to the vegetation type shows good agreement between the LTDR V4 and MOD13C1 datasets. This study demonstrates the spatial and temporal consistencies and discrepancies between the AVHRR LTDR and MODIS MOD13C1 NDVI products in China, which could provide useful information for the choice of NDVI products in subsequent studies of vegetation dynamics. PMID:28587266

Comparison and Evaluation of Annual NDVI Time Series in China Derived from the NOAA AVHRR LTDR and Terra MODIS MOD13C1 Products.

PubMed

Guo, Xiaoyi; Zhang, Hongyan; Wu, Zhengfang; Zhao, Jianjun; Zhang, Zhengxiang

2017-06-06

Time series of Normalized Difference Vegetation Index (NDVI) derived from multiple satellite sensors are crucial data to study vegetation dynamics. The Land Long Term Data Record Version 4 (LTDR V4) NDVI dataset was recently released at a 0.05 × 0.05° spatial resolution and daily temporal resolution. In this study, annual NDVI time series that are composited by the LTDR V4 and Moderate Resolution Imaging Spectroradiometer (MODIS) NDVI datasets (MOD13C1) are compared and evaluated for the period from 2001 to 2014 in China. The spatial patterns of the NDVI generally match between the LTDR V4 and MOD13C1 datasets. The transitional zone between high and low NDVI values generally matches the boundary of semi-arid and sub-humid regions. A significant and high coefficient of determination is found between the two datasets according to a pixel-based correlation analysis. The spatially averaged NDVI of LTDR V4 is characterized by a much weaker positive regression slope relative to that of the spatially averaged NDVI of the MOD13C1 dataset because of changes in NOAA AVHRR sensors between 2005 and 2006. The measured NDVI values of LTDR V4 were always higher than that of MOD13C1 in western China due to the relatively lower atmospheric water vapor content in western China, and opposite observation appeared in eastern China. In total, 18.54% of the LTDR V4 NDVI pixels exhibit significant trends, whereas 35.79% of the MOD13C1 NDVI pixels show significant trends. Good agreement is observed between the significant trends of the two datasets in the Northeast Plain, Bohai Economic Rim, Loess Plateau, and Yangtze River Delta. By contrast, the datasets contrasted in northwestern desert regions and southern China. A trend analysis of the regression slope values according to the vegetation type shows good agreement between the LTDR V4 and MOD13C1 datasets. This study demonstrates the spatial and temporal consistencies and discrepancies between the AVHRR LTDR and MODIS MOD13C1 NDVI products in China, which could provide useful information for the choice of NDVI products in subsequent studies of vegetation dynamics.

Observations of Intrinsic Rotation Reversal Hysteresis in Alcator C-Mod Plasmas

NASA Astrophysics Data System (ADS)

Cao, Norman; Rice, John; White, Anne; Baek, Seung; Chilenski, Mark; Creely, Alexander; Ennever, Paul; Hubbard, Amanda; Hughes, Jerry; Irby, Jim; Rodriguez-Fernandez, Pablo; Reinke, Matthew; Diamond, Patrick; Alcator C-Mod Team

2016-10-01

Intrinsic core toroidal rotation in Alcator C-Mod L-mode plasmas has been observed to spontaneously reverse direction when the normalized collisionality ν*, evaluated at the profile minimum, passes through a critical value around 0.4. In Ohmic plasmas, the low density linear Ohmic confinement regime exhibits co-current toroidal rotation, and the higher density saturated Ohmic confinement regime exhibits counter-current rotation. The reversal manifests a hysteresis loop in ν*, where the critical collisionalities for the forward and reverse transitions differ by 10-15%. There appears to be memory associated with the rotation state, since reversals which do not begin from fully saturated rotation states do not manifest this hysteresis. In addition, high-k PCI fluctuation ``wings'' (kθρs up to 1) at low density and high current appear only in the co-current rotation state, while density peaking and ``non-local'' heat transport behavior do not appear to change significantly with the rotation state. Results from fluctuation measurements and preliminary transport and stability analyses will also be presented. This work is supported by the US DOE under Grant DE-FC02-99ER54512 (C-Mod).

Comparison of tungsten nano-tendrils grown in Alcator C-Mod and linear plasma devices

NASA Astrophysics Data System (ADS)

Wright, G. M.; Brunner, D.; Baldwin, M. J.; Bystrov, K.; Doerner, R. P.; Labombard, B.; Lipschultz, B.; De Temmerman, G.; Terry, J. L.; Whyte, D. G.; Woller, K. B.

2013-07-01

Growth of tungsten nano-tendrils ("fuzz") has been observed for the first time in the divertor region of a high-power density tokamak experiment. After 14 consecutive helium L-mode discharges in Alcator C-Mod, the tip of a tungsten Langmuir probe at the outer strike point was fully covered with a layer of nano-tendrils. The depth of the W fuzz layer (600 ± 150 nm) is consistent with an empirical growth formula from the PISCES experiment. Re-creating the C-Mod exposures as closely as possible in Pilot-PSI experiment can produce nearly-identical nano-tendril morphology and layer thickness at surface temperatures that agree with uncertainties with the C-Mod W probe temperature data. Helium concentrations in W fuzz layers are measured at 1-4 at.%, which is lower than expected for the observed sub-surface voids to be filled with several GPa of helium pressure. This possibly indicates that the void formation is not pressure driven.

Real-time sensing and gas jet mitigation of VDEs on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Granetz, R. S.; Wolfe, S. M.; Izzo, V. A.; Reinke, M. L.; Terry, J. L.; Hughes, J. W.; Zhurovich, K.; Whyte, D. G.; Bakhtiari, M.; Wurden, G.

2006-10-01

Experiments have been carried out in Alcator C-Mod to test the effectiveness of gas jet disruption mitigation of VDEs with real-time detection and triggering by the C-Mod digital plasma control system (DPCS). The DPCS continuously computes the error in the plasma vertical position from the magnetics diagnostics. When this error exceeds an adjustable preset value, the DPCS triggers the gas jet valve (with a negligible latency time). The high-pressure gas (argon) only takes a few milliseconds to enter the vacuum chamber and begin affecting the plasma, but this is comparable to the VDE timescale on C-Mod. Nevertheless, gas jet injection reduced the halo current, increased the radiated power fraction, and reduced the heating of the divertor compared to unmitigated disruptions, but not quite as well as in earlier mitigation experiments with vertically stable plasmas. Presumably a faster overall response time would be beneficial, and several ways to achieve this will also be discussed.

Insulation of Enhancer-Promoter Communication by a Gypsy Transposon Insert in the Drosophila cut Gene: Cooperation between Suppressor of Hairy-wing and Modifier of mdg4 Proteins

PubMed Central

Gause, Maria; Morcillo, Patrick; Dorsett, Dale

2001-01-01

The Drosophila mod(mdg4) gene products counteract heterochromatin-mediated silencing of the white gene and help activate genes of the bithorax complex. They also regulate the insulator activity of the gypsy transposon when gypsy inserts between an enhancer and promoter. The Su(Hw) protein is required for gypsy-mediated insulation, and the Mod(mdg4)-67.2 protein binds to Su(Hw). The aim of this study was to determine whether Mod(mdg4)-67.2 is a coinsulator that helps Su(Hw) block enhancers or a facilitator of activation that is inhibited by Su(Hw). Here we provide evidence that Mod(mdg4)-67.2 acts as a coinsulator by showing that some loss-of-function mod(mdg4) mutations decrease enhancer blocking by a gypsy insert in the cut gene. We find that the C terminus of Mod(mdg4)-67.2 binds in vitro to a region of Su(Hw) that is required for insulation, while the N terminus mediates self-association. The N terminus of Mod(mdg4)-67.2 also interacts with the Chip protein, which facilitates activation of cut. Mod(mdg4)-67.2 truncated in the C terminus interferes in a dominant-negative fashion with insulation in cut but does not significantly affect heterochromatin-mediated silencing of white. We infer that multiple contacts between Su(Hw) and a Mod(mdg4)-67.2 multimer are required for insulation. We theorize that Mod(mdg4)-67.2 usually aids gene activation but can also act as a coinsulator by helping Su(Hw) trap facilitators of activation, such as the Chip protein. PMID:11416154

The NASA Lewis large wind turbine program

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Baldwin, D. H.

1981-01-01

The program is directed toward development of the technology for safe, reliable, environmentally acceptable large wind turbines that have the potential to generate a significant amount of electricity at costs competitive with conventional electric generation systems. In addition, these large wind turbines must be fully compatible with electric utility operations and interface requirements. Advances are made by gaining a better understanding of the system design drivers, improvements in the analytical design tools, verification of design methods with operating field data, and the incorporation of new technology and innovative designs. An overview of the program activities is presented and includes results from the first and second generation field machines (Mod-OA, -1, and -2), the design phase of the third generation wind turbine (Mod-5) and the advanced technology projects. Also included is the status of the Department of Interior WTS-4 machine.

High-intensity intermittent swimming improves cardiovascular health status for women with mild hypertension.

PubMed

Mohr, Magni; Nordsborg, Nikolai Baastrup; Lindenskov, Annika; Steinholm, Hildigunn; Nielsen, Hans Petur; Mortensen, Jann; Weihe, Pal; Krustrup, Peter

2014-01-01

To test the hypothesis that high-intensity swim training improves cardiovascular health status in sedentary premenopausal women with mild hypertension, sixty-two women were randomized into high-intensity (n = 21; HIT), moderate-intensity (n = 21; MOD), and control groups (n = 20; CON). HIT performed 6-10 × 30 s all-out swimming interspersed by 2 min recovery and MOD swam continuously for 1 h at moderate intensity for a 15-week period completing in total 44 ± 1 and 43 ± 1 sessions, respectively. In CON, all measured variables were similar before and after the intervention period. Systolic BP decreased (P < 0.05) by 6 ± 1 and 4 ± 1 mmHg in HIT and MOD; respectively. Resting heart rate declined (P < 0.05) by 5 ± 1 bpm both in HIT and MOD, fat mass decreased (P < 0.05) by 1.1 ± 0.2 and 2.2 ± 0.3 kg, respectively, while the blood lipid profile was unaltered. In HIT and MOD, performance improved (P < 0.05) for a maximal 10 min swim (13 ± 3% and 22 ± 3%), interval swimming (23 ± 3% and 8 ± 3%), and Yo-Yo IE1 running performance (58 ± 5% and 45 ± 4%). In conclusion, high-intensity intermittent swimming is an effective training strategy to improve cardiovascular health and physical performance in sedentary women with mild hypertension. Adaptations are similar with high- and moderate-intensity training, despite markedly less total time spent and distance covered in the high-intensity group.

High-Intensity Intermittent Swimming Improves Cardiovascular Health Status for Women with Mild Hypertension

PubMed Central

Mohr, Magni; Nordsborg, Nikolai Baastrup; Lindenskov, Annika; Steinholm, Hildigunn; Nielsen, Hans Petur; Mortensen, Jann; Weihe, Pal; Krustrup, Peter

2014-01-01

To test the hypothesis that high-intensity swim training improves cardiovascular health status in sedentary premenopausal women with mild hypertension, sixty-two women were randomized into high-intensity (n = 21; HIT), moderate-intensity (n = 21; MOD), and control groups (n = 20; CON). HIT performed 6–10 × 30 s all-out swimming interspersed by 2 min recovery and MOD swam continuously for 1 h at moderate intensity for a 15-week period completing in total 44 ± 1 and 43 ± 1 sessions, respectively. In CON, all measured variables were similar before and after the intervention period. Systolic BP decreased (P < 0.05) by 6 ± 1 and 4 ± 1 mmHg in HIT and MOD; respectively. Resting heart rate declined (P < 0.05) by 5 ± 1 bpm both in HIT and MOD, fat mass decreased (P < 0.05) by 1.1 ± 0.2 and 2.2 ± 0.3 kg, respectively, while the blood lipid profile was unaltered. In HIT and MOD, performance improved (P < 0.05) for a maximal 10 min swim (13 ± 3% and 22 ± 3%), interval swimming (23 ± 3% and 8 ± 3%), and Yo-Yo IE1 running performance (58 ± 5% and 45 ± 4%). In conclusion, high-intensity intermittent swimming is an effective training strategy to improve cardiovascular health and physical performance in sedentary women with mild hypertension. Adaptations are similar with high- and moderate-intensity training, despite markedly less total time spent and distance covered in the high-intensity group. PMID:24812628

The measurement of the intrinsic impurities of molybdenum and carbon in the Alcator C-Mod tokamak plasma using low resolution spectroscopy

NASA Astrophysics Data System (ADS)

May, M. J.; Finkenthal, M.; Regan, S. P.; Moos, H. W.; Terry, J. L.; Goetz, J. A.; Graf, M. A.; Rice, J. E.; Marmar, E. S.; Fournier, K. B.; Goldstein, W. H.

1997-06-01

The intrinsic impurity content of molybdenum and carbon was measured in the Alcator C-Mod tokamak using low resolution, multilayer mirror (MLM) spectroscopy ( Delta lambda ~1-10 AA). Molybdenum was the dominant high-Z impurity and originated from the molybdenum armour tiles covering all of the plasma facing surfaces (including the inner column, the poloidal divertor plates and the ion cyclotron resonant frequency (ICRF) limiter) at Alcator C-Mod. Despite the all metal first wall, a carbon concentration of 1 to 2% existed in the plasma and was the major low-Z impurity in Alcator C-Mod. Thus, the behaviour of intrinsic molybdenum and carbon penetrating into the main plasma and the effect on the plasma must be measured and characterized during various modes of Alcator C-Mod operation. To this end, soft X-ray extreme ultraviolet (XUV) emission lines of charge states, ranging from hydrogen-like to helium-like lines of carbon (radius/minor radius, r/a~1) at the plasma edge to potassium to chlorine-like (0.4

First results of the SOL reflectometer on Alcator C-Mod.

PubMed

Lau, C; Hanson, G; Lin, Y; Wilgen, J; Wukitch, S; Labombard, B; Wallace, G

2012-10-01

A swept-frequency X-mode reflectometer has been built on Alcator C-Mod to measure the scrape-off layer (SOL) density profiles adjacent to the lower hybrid launcher. The reflectometer system operates between 100 and 146 GHz at sweep rates from 10 μs to 1 ms and covers a density range of ∼10(16)-10(20) m(-3) at B(0) = 5-5.4 T. This paper discusses the analysis of reflectometer density profiles and presents first experimental results of SOL density profile modifications due to the application of lower hybrid range-of-frequencies power to L-mode discharges. Comparison between density profiles measured by the X-mode reflectometer and scanning Langmuir probes is also shown.

Anomalous transport in the H-mode pedestal of Alcator C-Mod discharges

NASA Astrophysics Data System (ADS)

Pankin, A. Y.; Hughes, J. W.; Greenwald, M. J.; Kritz, A. H.; Rafiq, T.

2017-02-01

Anomalous transport in the H-mode pedestal region of five Alcator C-Mod discharges, representing a collisionality scan is analyzed. The understanding of anomalous transport in the pedestal region is important for the development of a comprehensive model for the H-mode pedestal slope. In this research, a possible role of the drift resistive inertial ballooning modes (Rafiq et al 2010 Phys. Plasmas 17 082511) in the edge of Alcator C-Mod discharges is analyzed. The stability analysis, carried out using the TRANSP code, indicates that the DRIBM modes are strongly unstable in Alcator C-Mod discharges with large electron collisionality. An improved interpretive analysis of H-mode pedestal experimental data is carried out utilizing the additive flux minimization technique (Pankin et al 2013 Phys. Plasmas 20 102501) together with the guiding-center neoclassical kinetic XGC0 code. The neoclassical and neutral physics are simulated in the XGC0 code and the anomalous fluxes are computed using the additive flux minimization technique. The anomalous fluxes are reconstructed and compared with each other for the collisionality scan Alcator C-Mod discharges. It is found that the electron thermal anomalous diffusivities at the pedestal top increase with the electron collisionality. This dependence can also point to the drift resistive inertial ballooning modes as the modes that drive the anomalous transport in the plasma edge of highly collisional discharges.

Mod-2 wind turbine project assessment and cluster test plans

NASA Technical Reports Server (NTRS)

Gordon, L. H.

1982-01-01

An assessment of the Mod-2 Wind Turbine project is presented based on initial goals and present results. Specifically, the Mod-2 background, project flow, and a chronology of events/results leading to Mod-2 acceptance is presented. After checkout/acceptance of the three operating turbines, NASA/LeRC will continue management of a two year test program performed at the DOE Goodnoe Hills test site. This test program is expected to yield data necessary for the continued development and optimization of wind energy systems. These test activities, the implementation of, and the results to date are also presented.

MOD: An Organic Detector for the Future Exploration of Mars

NASA Technical Reports Server (NTRS)

Kminek, G.; Bada, J. L.; Botta, O.; Grunthaner, F.; Glavin, D. P.

1999-01-01

The Mars Organic Detector (MOD) is designed to assess whether organic compounds, possibly associated with life, are present in Martian rock and soil samples. MOD has a detection limit that is at least two orders of magnitude more sensitive than the Viking GCMS. MOD is focused on detecting amino acids, amines and PAH (polycyclic aromatic hydrocarbons). Amino acids play an essential role in biochemistry on Earth and PAH are widespread throughout the universe and can provide an indication of the delivery of meteoritic organic material to Mars. The advantage of MOD is the absence of wet chemistry and its simple and robust design. The sample will be extracted from the mineral matrix (0.1 - 1 g of rock-powder) using sublimation and analyzed with a fluorescence detector. The isolation method is based on the fact that amino acids and PAH are volatile at temperatures greater than 150C. The fluorescence detection scheme is based on UV excitation with LED's, optical filters, PrN diode photon detector and a sample calibration reservoir. Fluorescamine is used as a fluorescing reagent for amino acids and amines, while PAH are naturally fluorescent. There is no sample preparation required and the turnaround time for a single analysis is on the order of minutes.

Multi-channel transport experiments at Alcator C-Mod and comparison with gyrokinetic simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, A. E.; Howard, N. T.; Greenwald, M.

2013-05-15

Multi-channel transport experiments have been conducted in auxiliary heated (Ion Cyclotron Range of Frequencies) L-mode plasmas at Alcator C-Mod [Marmar and Alcator C-Mod Group, Fusion Sci. Technol. 51(3), 3261 (2007)]. These plasmas provide good diagnostic coverage for measurements of kinetic profiles, impurity transport, and turbulence (electron temperature and density fluctuations). In the experiments, a steady sawtoothing L-mode plasma with 1.2 MW of on-axis RF heating is established and density is scanned by 20%. Measured rotation profiles change from peaked to hollow in shape as density is increased, but electron density and impurity profiles remain peaked. Ion or electron heat fluxesmore » from the two plasmas are the same. The experimental results are compared directly to nonlinear gyrokinetic theory using synthetic diagnostics and the code GYRO [Candy and Waltz, J. Comput. Phys. 186, 545 (2003)]. We find good agreement with experimental ion heat flux, impurity particle transport, and trends in the fluctuation level ratio (T(tilde sign){sub e}/T{sub e})/(ñ{sub e}/n{sub e}), but underprediction of electron heat flux. We find that changes in momentum transport (rotation profiles changing from peaked to hollow) do not correlate with changes in particle transport, and also do not correlate with changes in linear mode dominance, e.g., Ion Temperature Gradient versus Trapped Electron Mode. The new C-Mod results suggest that the drives for momentum transport differ from drives for heat and particle transport. The experimental results are inconsistent with present quasilinear models, and the strong sensitivity of core rotation to density remains unexplained.« less

A new approach to evaluate the MODIS annual NPP product (MOD17A3) using forest field data from Turkey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gulbeyaz, Onder; Bond-Lamberty, Ben; Akyurek, Zuhal

In this study we present the first evaluation of the MODIS (MODerate resolution Imaging Spectroradiometer) annual Net Primary Product (NPP) for Turkey's forest ecosystems using field measurements. Due to lack of country scale field measurements (i.e. flux tower for forest ecosystems), tree DBH (Diameter at Breast Height) dataset provided by Ministry of Forest and Water Affair (MFWA) of Turkey is used to calculate NPP of Turkey’s forest ecosystems. The lack of a reliable NPP dataset leads the researchers to use global NPP models such as MODIS annual NPP product. The MODIS MOD17A3 product of vegetation net primary production (NPP) ismore » one of the most highly used data sources for studies of global carbon 25 cycle. However, it is still necessary to test its predictions in multiple biomes, especially for heterogeneous areas in terms of its accuracy and potential bias. Here, we studied a new approach to evaluate coarse scale NPP estimates from the MODIS NPP- MOD17A3 data product, using 2008-2013 field measurements of tree growth throughout Turkey. There different methods were used to calculate field NPP, including standardized growth coefficients (MC), growth coefficients from North America (JC) and annual expected increment (AEI). The average NPP values for all the country is calculated as 2.06 kgC m-2(5years)-1 (0.412 kgC m-2 year-1) (SD = 1.15 kgC m-2 (5years)-1) from MOD17A3, 0.90 kgC m-2(5years)-1 (0.18 kgC m-2 year-1) (SD = 0.57 kgC m-2(5years)-1) with MC, 0.63 kgC m-2(5years)-1 (0.126 kgC m-2 year-1) (SD = 0.37 kgC m-2(5years)-1) with JC and 0.58 kgC m-2 year-1 (SD = 0.29 kgC m-2(5years)-1) with AEI for the studied plots. We found that the MODIS NPP product has a clear relation with both the NPP estimates obtained by using MC (R36 2 = 0.34, RMSE=1.51 kgC m-2(5years)-1) and JC (R37 2 = 0.32, RMSE = 1.73 kgC m-2(5years)-1). In addition to that, the relation between MOD17A3 product and AEI-derived NPP is relatively strong (R39 2 = 0.48, RMSE = 0.26 kgC m-2 year-1). We discuss possible reasons for these trade-offs among different methods. This study lays out a new approach to validate coarse scale MODIS product using field data directly, including for highly heterogeneous areas.« less

Binding of ReO[subscript 4];#8722; with an engineered MoO[subscript 4 superscript 2];#8722;-binding protein: towards a new approach in radiopharmaceutical applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aryal, Baikuntha P.; Brugarolas, Pedro; He, Chuan

2012-05-25

Radiolabeled biomolecules are routinely used for clinical diagnostics. {sup 99m}Tc is the most commonly used radioactive tracer in radiopharmaceuticals. {sup 188}Re and {sup 186}Re are also commonly used as radioactive tracers in medicine. However, currently available methods for radiolabeling are lengthy and involve several steps in bioconjugation processes. In this work we present a strategy to engineer proteins that may selectively recognize the perrhenate (ReO{sub 4}{sup -}) ion as a new way to label proteins. We found that a molybdate (MoO{sub 4}{sup 2-})-binding protein (ModA) from Escherichia coli can bind perrhenate with high affinity. Using fluorescence and isothermal titration calorimetrymore » measurements, we determined the dissociation constant of ModA for ReO{sub 4}{sup -} to be 541 nM and we solved a crystal structure of ModA with a bound ReO{sub 4}{sup -}. On the basis of the structure we created a mutant protein containing a disulfide linkage, which exhibited increased affinity for perrhenate (K{sub d} = 104 nM). High-resolution crystal structures of ModA (1.7 {angstrom}) and A11C/R153C mutant (2.0 {angstrom}) were solved with bound perrhenate. Both structures show that a perrhenate ion occupies the molybdate binding site using the same amino acid residues that are involved in molybdate binding. The overall structure of the perrhenate-bound ModA is unchanged compared with that of the molybdate-bound form. In the mutant protein, the bound perrhenate is further stabilized by the engineered disulfide bond.« less

Pedestal turbulence simulations using GENE

NASA Astrophysics Data System (ADS)

Liu, Xing; Kotschenreuther, M.; Hatch, D. R.; Zheng, L. J.; Mahajan, S.; Diallo, A.; Groebner, R. J.; Hubbard, A. E.; Hughes, J. W.; Maggi, C. F.; Saarelma, S.; JET Contributors

2017-10-01

We match frequencies, power balance, and other transport characteristics of several pedestals-two DIIID ELMy H-modes and a C-Mod I-mode, and attempt this for a C-Mod ELMy H-mode. Observed quasi-coherent fluctuations (QCFs) on the DIIID shots are identified as MTMs. The MTMs match frequency and power balance (with slight adjustment of temperature profile), and cause low transport in the density, ion heat and impurity channels- consistent with observed inter-ELM evolution of ion and electron temperature, electron and impurity density, or transport analysis of those channels. KBM can be ruled out as the dominant agent for heat transport. We find the Weakly Coherent Mode on C-Mod I-mode may be an electrostatic heavy particle/ITG mode. Analysis is ongoing for the C-Mod ELMy H-mode QCF. Pedestal density profiles in JET-ILW are consistent with ITG induced particle pinch. Work supported by US DOE under DE-FC02-04ER54698, DE-FG02-04ER54742 and DE-FC02-99ER54512 and by Eurofusion under Grant No. 633053.

A spatially resolving x-ray crystal spectrometer for measurement of ion-temperature and rotation-velocity profiles on the Alcator C-Mod tokamak.

PubMed

Hill, K W; Bitter, M L; Scott, S D; Ince-Cushman, A; Reinke, M; Rice, J E; Beiersdorfer, P; Gu, M-F; Lee, S G; Broennimann, Ch; Eikenberry, E F

2008-10-01

A new spatially resolving x-ray crystal spectrometer capable of measuring continuous spatial profiles of high resolution spectra (lambda/d lambda>6000) of He-like and H-like Ar K alpha lines with good spatial (approximately 1 cm) and temporal (approximately 10 ms) resolutions has been installed on the Alcator C-Mod tokamak. Two spherically bent crystals image the spectra onto four two-dimensional Pilatus II pixel detectors. Tomographic inversion enables inference of local line emissivity, ion temperature (T(i)), and toroidal plasma rotation velocity (upsilon(phi)) from the line Doppler widths and shifts. The data analysis techniques, T(i) and upsilon(phi) profiles, analysis of fusion-neutron background, and predictions of performance on other tokamaks, including ITER, will be presented.

The Multi-Spectral Imaging Diagnostic on Alcator C-MOD and TCV

NASA Astrophysics Data System (ADS)

Linehan, B. L.; Mumgaard, R. T.; Duval, B. P.; Theiler, C. G.; TCV Team

2017-10-01

The Multi-Spectral Imaging (MSI) diagnostic is a new instrument that captures simultaneous spectrally filtered images from a common sight view while maintaining a large tendue and high spatial resolution. The system uses a polychromator layout where each image is sequentially filtered. This procedure yields a high transmission for each spectral channel with minimal vignetting and aberrations. A four-wavelength system was installed on Alcator C-Mod and then moved to TCV. The system uses industrial cameras to simultaneously image the divertor region at 95 frames per second at f/# 2.8 via a coherent fiber bundle (C-Mod) or a lens-based relay optic (TCV). The images are absolutely calibrated and spatially registered enabling accurate measurement of atomic line ratios and absolute line intensities. The images will be used to study divertor detachment by imaging impurities and Balmer series emissions. Furthermore, the large field of view and an ability to support many types of detectors opens the door for other novel approaches to optically measuring plasma with high temporal, spatial, and spectral resolution. Such measurements will allow for the study of Stark broadening and divertor turbulence. Here, we present the first measurements taken with this cavity imaging system. USDoE awards DE-FC02-99ER54512 and award DE-AC05-06OR23100, ORISE, administered by ORAU.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Antonelli, M. (Editor)

1983-01-01

Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Rohdenburg, C.; Vatsky, A.; Antonelli, M. (Editor)

1983-01-01

Activities performed on Mod I engine testing and test results, testing of the Mod I engine in the United States, Mod I engine characterization and analyses, Mod I Transient Test Bed fuel economy, upgraded Mod I performance and testing, Stirling engine reference engine manufacturing and reduced size studied, components and subsystems, and the study and test of low cost casting alloys are summarized. The overall program philosophy is outlined, and data and results are presented.

Prediction and realization of ITER-like pedestal pressure in the high- B tokamak Alcator C-Mod

NASA Astrophysics Data System (ADS)

Hughes, Jerry

2017-10-01

Fusion power in a burning plasma will scale as the square of the plasma pressure, which is increased in a straightforward way by increasing magnetic field: Pfus p2 B4 . Experiments on Alcator C-Mod, a compact high- B tokamak, have tested predictive capability for pedestal pressure, at toroidal field BT up to 8T , and poloidal field BP up to 1T . These reactor-like fields enable C-Mod to approach an ITER predicted value of 90kPa . This is expected if, as in the EPED model, the pedestal is constrained by onset of kinetic ballooning modes (KBMs) and peeling-ballooning modes (PMB), yielding a pressure pedestal approximately as pped BT ×BP . One successful path to high confinement on C-Mod is the high-density (ne > 3 ×1020m-3) approach, pursued using enhanced D-alpha (EDAs) H-mode. In EDA H-mode, transport regulates both the pedestal profiles and the core impurity content, holding the pedestal stationary, at just below the PBM stability boundary. We have extended this stationary ELM-suppressed regime to the highest magnetic fields achievable on C-Mod, and used it to approach the maximum pedestal predicted by EPED at high density: pped 60kPa . Another approach to high pressure utilizes a pedestal limited by PBMs at low collisionality, where pressure increases with density and EPED predicts access to a higher ``Super H'' solution for pped. Experiments at reduced density (ne < 2 ×1020m-3) and strong plasma shaping (δ > 0.5) accessed these regimes on C-Mod, producing pedestals with world record pped 80kPa , at Tped 2keV . In both the high and low density approaches, the impact of the pedestal on core performance is substantial. Our exploration of high pedestal regimes yielded a volume-averaged pressure 〈 p 〉 > 2atm , a world record value for a magnetic fusion device. The results hold promise for the projection of pedestal pressure and overall performance of high field burning plasma devices. Supported by U.S. Department of Energy awards DE-FC02-99ER54512, DE-FG02-95ER54309, DE-FC02-06ER54873, DE-AC02-09CH11466, DE-SC0007880 using Alcator C-Mod, a DOE Office of Science User Facility.

MOD-5A wind turbine generator program design report: Volume 1: Executive Summary

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator covering work performed between July 1980 and June 1984 is discussed. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 1, the Executive Summary, summarizes all phases of the MOD-5A program. The performance and cost of energy generated by the MOD-5A are presented. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation, power generation, and control and instrumentation subsystems - is described briefly. The early phases of the MOD-5A program, during which the design was analyzed and optimized, and new technologies and materials were developed, are discussed. Manufacturing, quality assurance, and safety plans are presented. The volume concludes with an index of volumes 2 and 3.

Specific etiologies associated with the multiple organ dysfunction syndrome in children: Part 2

PubMed Central

Upperman, Jeffrey S.; Bucuvalas, John C.; Williams, Felicia N.; Cairns, Bruce A.; Cox, Charles S.; Doctor, Allan; Tamburro, Robert F.

2016-01-01

Objective To describe a number of conditions and therapies associated with multiple organ dysfunction syndrome (MODS) presented as part of the Eunice Kennedy Shriver National Institute of Child Health and Human Development MODS Workshop (March 26–27, 2015). In addition, the relationship between burn injuries and MODS is also included although it was not discussed at the Workshop. Data Sources Literature review, research data, and expert opinion. Study Selection Not applicable. Data Extraction Moderated by an expert from the field, issues relevant to the association of MODS with a variety of conditions and therapies were presented, discussed and debated with a focus on identifying knowledge gaps and research priorities. Data Synthesis Summary of presentations and discussion supported and supplemented by relevant literature. Conclusions Sepsis and trauma are the two conditions most commonly associated with MODS both in children and adults. However, many other pathophysiologic processes may result in MODS. In this paper, we discuss conditions such as liver failure and pancreatitis, pathophysiologic processes such as ischemia and hypoxia, and injuries such as trauma and burns. Additionally, therapeutic interventions such as medications, blood transfusions, transplantation may also precipitate and contribute to MODS. The purpose of this manuscript is to describe the association of MODS with a variety of conditions and therapies in an attempt to identify similarities, differences and opportunities for therapeutic intervention. PMID:28248835

Tungsten impurity transport experiments in Alcator C-Mod to address high priority research and development for ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loarte, A.; Polevoi, A. R.; Hosokawa, M.

2015-05-15

Experiments in Alcator C-Mod tokamak plasmas in the Enhanced D-alpha H-mode regime with ITER-like mid-radius plasma density peaking and Ion Cyclotron Resonant heating, in which tungsten is introduced by the laser blow-off technique, have demonstrated that accumulation of tungsten in the central region of the plasma does not take place in these conditions. The measurements obtained are consistent with anomalous transport dominating tungsten transport except in the central region of the plasma where tungsten transport is neoclassical, as previously observed in other devices with dominant neutral beam injection heating, such as JET and ASDEX Upgrade. In contrast to such results,more » however, the measured scale lengths for plasma temperature and density in the central region of these Alcator C-Mod plasmas, with density profiles relatively flat in the core region due to the lack of core fuelling, are favourable to prevent inter and intra sawtooth tungsten accumulation in this region under dominance of neoclassical transport. Simulations of ITER H-mode plasmas, including both anomalous (modelled by the Gyro-Landau-Fluid code GLF23) and neoclassical transport for main ions and tungsten and with density profiles of similar peaking to those obtained in Alcator C-Mod show that accumulation of tungsten in the central plasma region is also unlikely to occur in stationary ITER H-mode plasmas due to the low fuelling source by the neutral beam injection (injection energy ∼ 1 MeV), which is in good agreement with findings in the Alcator C-Mod experiments.« less

Development of a spatially resolving x-ray crystal spectrometer for measurement of ion-temperature (T(i)) and rotation-velocity (v) profiles in ITER.

PubMed

Hill, K W; Bitter, M; Delgado-Aparicio, L; Johnson, D; Feder, R; Beiersdorfer, P; Dunn, J; Morris, K; Wang, E; Reinke, M; Podpaly, Y; Rice, J E; Barnsley, R; O'Mullane, M; Lee, S G

2010-10-01

Imaging x-ray crystal spectrometer (XCS) arrays are being developed as a US-ITER activity for Doppler measurement of T(i) and v profiles of impurities (W, Kr, and Fe) with ∼7 cm (a/30) and 10-100 ms resolution in ITER. The imaging XCS, modeled after a prototype instrument on Alcator C-Mod, uses a spherically bent crystal and 2D x-ray detectors to achieve high spectral resolving power (E/dE>6000) horizontally and spatial imaging vertically. Two arrays will measure T(i) and both poloidal and toroidal rotation velocity profiles. The measurement of many spatial chords permits tomographic inversion for the inference of local parameters. The instrument design, predictions of performance, and results from C-Mod are presented.

Manned Certification Tests of the Modernized MK 16 MOD 1

DTIC Science & Technology

2013-11-01

CERTIFICATION TESTS OF THE MODERNIZED MK 16 MOD 1 Authors: D. E . Warkander, Ph.D. D. J. Doolette, Ph.D...PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Dan E . Warkander; David J. Doolette; Paul C. Algra 5d. PROJECT NUMBER 5e. TASK NUMBER 10-08 5f. WORK UNIT...electronics must be turned on when calibrating the secondary display. 11 REFERENCES 1. R. P. Layton , Unmanned Evaluation of the Modernized MK 16 MOD

Cause for Concern or Moral Panic? The Prospects of the Swedish Mods in Retrospect

ERIC Educational Resources Information Center

Alm, Susanne; Nilsson, Anders

2011-01-01

The Swedish mods of the 1960s frightened the parental generation like few other youth cultures. Was the concern justified--was the mod culture a hotbed of social maladjustment? Or would the mods come to live conventional lives to the same extent as their peers? We present analyses from a large longitudinal study allowing for a follow-up of…

Validation of nonlinear gyrokinetic simulations of L- and I-mode plasmas on Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Creely, A. J.; Howard, N. T.; Rodriguez-Fernandez, P.

New validation of global, nonlinear, ion-scale gyrokinetic simulations (GYRO) is carried out for L- and I-mode plasmas on Alcator C-Mod, utilizing heat fluxes, profile stiffness, and temperature fluctuations. Previous work at C-Mod found that ITG/TEM-scale GYRO simulations can match both electron and ion heat fluxes within error bars in I-mode [White PoP 2015], suggesting that multi-scale (cross-scale coupling) effects [Howard PoP 2016] may be less important in I-mode than in L-mode. New results presented here, however, show that global, nonlinear, ion-scale GYRO simulations are able to match the experimental ion heat flux, but underpredict electron heat flux (at most radii),more » electron temperature fluctuations, and perturbative thermal diffusivity in both L- and I-mode. Linear addition of electron heat flux from electron scale runs does not resolve this discrepancy. These results indicate that single-scale simulations do not sufficiently describe the I-mode core transport, and that multi-scale (coupled electron- and ion-scale) transport models are needed. In conclusion a preliminary investigation with multi-scale TGLF, however, was unable to resolve the discrepancy between ion-scale GYRO and experimental electron heat fluxes and perturbative diffusivity, motivating further work with multi-scale GYRO simulations and a more comprehensive study with multi-scale TGLF.« less

Validation of nonlinear gyrokinetic simulations of L- and I-mode plasmas on Alcator C-Mod

DOE PAGES

Creely, A. J.; Howard, N. T.; Rodriguez-Fernandez, P.; ...

2017-03-02

New validation of global, nonlinear, ion-scale gyrokinetic simulations (GYRO) is carried out for L- and I-mode plasmas on Alcator C-Mod, utilizing heat fluxes, profile stiffness, and temperature fluctuations. Previous work at C-Mod found that ITG/TEM-scale GYRO simulations can match both electron and ion heat fluxes within error bars in I-mode [White PoP 2015], suggesting that multi-scale (cross-scale coupling) effects [Howard PoP 2016] may be less important in I-mode than in L-mode. New results presented here, however, show that global, nonlinear, ion-scale GYRO simulations are able to match the experimental ion heat flux, but underpredict electron heat flux (at most radii),more » electron temperature fluctuations, and perturbative thermal diffusivity in both L- and I-mode. Linear addition of electron heat flux from electron scale runs does not resolve this discrepancy. These results indicate that single-scale simulations do not sufficiently describe the I-mode core transport, and that multi-scale (coupled electron- and ion-scale) transport models are needed. In conclusion a preliminary investigation with multi-scale TGLF, however, was unable to resolve the discrepancy between ion-scale GYRO and experimental electron heat fluxes and perturbative diffusivity, motivating further work with multi-scale GYRO simulations and a more comprehensive study with multi-scale TGLF.« less

Disruption prediction investigations using Machine Learning tools on DIII-D and Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rea, C.; Granetz, R. S.; Montes, K.

Using data-driven methodology, we exploit the time series of relevant plasma parameters for a large set of disrupted and non-disrupted discharges to develop a classification algorithm for detecting disruptive phases in shots that eventually disrupt. Comparing the same methodology on different devices is crucial in order to have information on the portability of the developed algorithm and the possible extrapolation to ITER. Therefore, we use data from two very different tokamaks, DIII-D and Alcator C-Mod. We then focus on a subset of disruption predictors, most of which are dimensionless and/or machine-independent parameters, coming from both plasma diagnostics and equilibrium reconstructions,more » such as the normalized plasma internal inductance ℓ and the n = 1 mode amplitude normalized to the toroidal magnetic field. Using such dimensionless indicators facilitates a more direct comparison between DIII-D and C-Mod. We then choose a shallow Machine Learning technique, called Random Forests, to explore the databases available for the two devices. We show results from the classification task, where we introduce a time dependency through the definition of class labels on the basis of the elapsed time before the disruption (i.e. ‘far from a disruption’ and ‘close to a disruption’). The performances of the different Random Forest classifiers are discussed in terms of several metrics, by showing the number of successfully detected samples, as well as the misclassifications. The overall model accuracies are above 97% when identifying a ‘far from disruption’ and a ‘disruptive’ phase for disrupted discharges. Nevertheless, the Forests are intrinsically different in their capability of predicting a disruptive behavior, with C-Mod predictions comparable to random guesses. Indeed, we show that C-Mod recall index, i.e. the sensitivity to a disruptive behavior, is as low as 0.47, while DIII-D recall is ~0.72. The portability of the developed algorithm is also tested across the two devices, by using DIII-D data for training the forests and C-Mod for testing and vice versa.« less

A long-term simulation of forest carbon fluxes over the Qilian Mountains

NASA Astrophysics Data System (ADS)

Yan, Min; Tian, Xin; Li, Zengyuan; Chen, Erxue; Li, Chunmei; Fan, Wenwu

2016-10-01

In this work, we integrated a remote-sensing-based (the MODIS MOD_17 Gross Primary Productivity (GPP) model (MOD_17)) and a process-based (the Biome-BioGeochemical Cycles (Biome-BGC) model) ecological model in order to estimate long-term (from 2000 to 2012) forest carbon fluxes over the Qilian Mountains in northwest China, a cold and arid forest ecosystem. Our goal was to obtain an accurate and quantitative simulation of spatial GPP patterns using the MOD_17 model and a temporal description of forest processes using the Biome-BGC model. The original MOD_17 model was first optimized using a biome-specific parameter, observed meteorological data, and reproduced fPAR at the eddy covariance site. The optimized MOD_17 model performed much better (R2 = 0.91, RMSE = 5.19 gC/m2/8d) than the original model (R2 = 0.47, RMSE = 20.27 gC/m2/8d). The Biome-BGC model was then calibrated using GPP for 30 representative forest plots selected from the optimized MOD_17 model. The calibrated Biome-BGC model was then driven in order to estimate forest GPP, net primary productivity (NPP), and net ecosystem exchange (NEE). GPP and NEE were validated against two-year (2010 and 2011) EC measurements (R2 = 0.79, RMSE = 1.15 gC/m2/d for GPP; and R2 = 0.69, RMSE = 1.087 gC/m2/d for NEE). NPP estimates from 2000 to 2012 were then compared to dendrochronological measurements (R2 = 0.73, RMSE = 24.46 gC/m2/yr). Our results indicated that integration of the two models can be used for estimating carbon fluxes with good accuracy and a high temporal and spatial resolution. Overall, NPP displayed a downward trend, with an average rate of 0.39 gC/m2/yr, from 2000 and 2012 over the Qilian Mountains. Simulated average annual NPP yielded higher values for the southeast as compared to the northwest. The most positive correlative climatic factor to average annual NPP was downward shortwave radiation. The vapor pressure deficit, and mean temperature and precipitation yielded negative correlations to average annual NPP.

Disruption prediction investigations using Machine Learning tools on DIII-D and Alcator C-Mod

DOE PAGES

Rea, C.; Granetz, R. S.; Montes, K.; ...

2018-06-18

Using data-driven methodology, we exploit the time series of relevant plasma parameters for a large set of disrupted and non-disrupted discharges to develop a classification algorithm for detecting disruptive phases in shots that eventually disrupt. Comparing the same methodology on different devices is crucial in order to have information on the portability of the developed algorithm and the possible extrapolation to ITER. Therefore, we use data from two very different tokamaks, DIII-D and Alcator C-Mod. We then focus on a subset of disruption predictors, most of which are dimensionless and/or machine-independent parameters, coming from both plasma diagnostics and equilibrium reconstructions,more » such as the normalized plasma internal inductance ℓ and the n = 1 mode amplitude normalized to the toroidal magnetic field. Using such dimensionless indicators facilitates a more direct comparison between DIII-D and C-Mod. We then choose a shallow Machine Learning technique, called Random Forests, to explore the databases available for the two devices. We show results from the classification task, where we introduce a time dependency through the definition of class labels on the basis of the elapsed time before the disruption (i.e. ‘far from a disruption’ and ‘close to a disruption’). The performances of the different Random Forest classifiers are discussed in terms of several metrics, by showing the number of successfully detected samples, as well as the misclassifications. The overall model accuracies are above 97% when identifying a ‘far from disruption’ and a ‘disruptive’ phase for disrupted discharges. Nevertheless, the Forests are intrinsically different in their capability of predicting a disruptive behavior, with C-Mod predictions comparable to random guesses. Indeed, we show that C-Mod recall index, i.e. the sensitivity to a disruptive behavior, is as low as 0.47, while DIII-D recall is ~0.72. The portability of the developed algorithm is also tested across the two devices, by using DIII-D data for training the forests and C-Mod for testing and vice versa.« less

modPDZpep: a web resource for structure based analysis of human PDZ-mediated interaction networks.

PubMed

Sain, Neetu; Mohanty, Debasisa

2016-09-21

PDZ domains recognize short sequence stretches usually present in C-terminal of their interaction partners. Because of the involvement of PDZ domains in many important biological processes, several attempts have been made for developing bioinformatics tools for genome-wide identification of PDZ interaction networks. Currently available tools for prediction of interaction partners of PDZ domains utilize machine learning approach. Since, they have been trained using experimental substrate specificity data for specific PDZ families, their applicability is limited to PDZ families closely related to the training set. These tools also do not allow analysis of PDZ-peptide interaction interfaces. We have used a structure based approach to develop modPDZpep, a program to predict the interaction partners of human PDZ domains and analyze structural details of PDZ interaction interfaces. modPDZpep predicts interaction partners by using structural models of PDZ-peptide complexes and evaluating binding energy scores using residue based statistical pair potentials. Since, it does not require training using experimental data on peptide binding affinity, it can predict substrates for diverse PDZ families. Because of the use of simple scoring function for binding energy, it is also fast enough for genome scale structure based analysis of PDZ interaction networks. Benchmarking using artificial as well as real negative datasets indicates good predictive power with ROC-AUC values in the range of 0.7 to 0.9 for a large number of human PDZ domains. Another novel feature of modPDZpep is its ability to map novel PDZ mediated interactions in human protein-protein interaction networks, either by utilizing available experimental phage display data or by structure based predictions. In summary, we have developed modPDZpep, a web-server for structure based analysis of human PDZ domains. It is freely available at http://www.nii.ac.in/modPDZpep.html or http://202.54.226.235/modPDZpep.html . This article was reviewed by Michael Gromiha and Zoltán Gáspári.

Studies of Turbulence and Transport in Alcator C-Mod H-Mode Plasmas with Phase Contrast Imaging and Comparisons with GYRO

NASA Astrophysics Data System (ADS)

Porkolab, M.; Lin, L.; Edlund, E. M.; Rost, J. C.; Fiore, C. L.; Greenwald, M.; Mikkelsen, D.

2008-11-01

We present recent experimental measurements of turbulence and transport in C-Mod H-Mode plasmas with and without internal transport barriers (ITB) using the phase contrast imaging (PCI) diagnostic and compare the results with GYRO predictions. In plasmas without ITB, the fluctuation above 300 kHz observed by PCI agrees with ITG in GYRO simulation, including the direction of propagation, wavenumber spectrum, and absolute intensity within experimental uncertainly (+/-75%). After transition to ITBs, the observed overall fluctuation intensity increases. GYRO simulation in the core shows that ITG dominates in ITBs but its intensity is lower than the overall experimental measurements which may also include contributions from the plasma edge. These results, as well as the impact of varying ∇Ti, ∇n, and ExB shear on turbulence will be discussed. C.L. Fiore et al., Fusion Sci. Technol., 51, 303 (2007). M. Porkolab et al., IEEE Trans. Plasma Sci. 34, 229 (2006). J. Candy et al., Phys. Rev. Lett., 91, 045001 (2003).

Distribution and magnitude of type I error of model-based multipoint lod scores: implications for multipoint mod scores.

PubMed

Xing, Chao; Elston, Robert C

2006-07-01

The multipoint lod score and mod score methods have been advocated for their superior power in detecting linkage. However, little has been done to determine the distribution of multipoint lod scores or to examine the properties of mod scores. In this paper we study the distribution of multipoint lod scores both analytically and by simulation. We also study by simulation the distribution of maximum multipoint lod scores when maximized over different penetrance models. The multipoint lod score is approximately normally distributed with mean and variance that depend on marker informativity, marker density, specified genetic model, number of pedigrees, pedigree structure, and pattern of affection status. When the multipoint lod scores are maximized over a set of assumed penetrances models, an excess of false positive indications of linkage appear under dominant analysis models with low penetrances and under recessive analysis models with high penetrances. Therefore, caution should be taken in interpreting results when employing multipoint lod score and mod score approaches, in particular when inferring the level of linkage significance and the mode of inheritance of a trait.

Fast parallel DNA-based algorithms for molecular computation: quadratic congruence and factoring integers.

PubMed

Chang, Weng-Long

2012-03-01

Assume that n is a positive integer. If there is an integer such that M (2) ≡ C (mod n), i.e., the congruence has a solution, then C is said to be a quadratic congruence (mod n). If the congruence does not have a solution, then C is said to be a quadratic noncongruence (mod n). The task of solving the problem is central to many important applications, the most obvious being cryptography. In this article, we describe a DNA-based algorithm for solving quadratic congruence and factoring integers. In additional to this novel contribution, we also show the utility of our encoding scheme, and of the algorithm's submodules. We demonstrate how a variety of arithmetic, shifted and comparative operations, namely bitwise and full addition, subtraction, left shifter and comparison perhaps are performed using strands of DNA.

Moderate, but not vigorous, intensity exercise training reduces C-reactive protein.

PubMed

Fedewa, Michael V; Hathaway, Elizabeth D; Higgins, Simon; Forehand, Ronald L; Schmidt, Michael D; Evans, Ellen M

2018-06-01

Sprint interval cycle training is a contemporary popular mode of training but its relative efficacy, under conditions of matched energy expenditure, to reduce risk factors for cardiometabolic disease is incompletely characterised, especially in young women. The purpose of this investigation was to determine the relative efficacy of six weeks of moderate-intensity cycling (MOD-C) and vigorous sprint-interval cycling (VIG-SIC) on lipid profile, insulin (INS) and insulin resistance using the homeostatic model assessment (HOMA-IR) and C-reactive protein (CRP) in inactive, overweight/obese (OW/OB) young women. Participants (BMI ≥25 kg/m 2 , waist circumference ≥88 cm) were randomly assigned to MOD-C (20-30 min at 60-70% of heart rate reserve(HRR)) or VIG-SIC (5-7 repeated bouts 30-second maximal effort sprints, followed by four minutes of active recovery) supervised training three days/week for six weeks, with each group matched on energy expenditure. Adiposity (%Fat) was measured using dual x-ray absorptiometry. Forty-four participants (20.4 ± 1.6 years, 65.9% Caucasian, 29.8 ± 4.1 kg/m 2 ) were included in the analysis. The improvement in CRP observed in the MOD-C group was larger than the VIG-C group (p = .034). Overall, high-density lipoprotein (HDL-C) and low-density lipoprotein (LDL-C) levels improved following training (p < .05); however, total cholesterol, triglyceride, INS and HOMA-IR did not improve (p > .05). These results indicate MOD-C training may be more effective in reducing CRP than VIG-SIC.

Fast Wave Transmission Measurements on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Reardon, J.; Bonoli, P. T.; Porkolab, M.; Takase, Y.; Wukitch, S. J.

1997-11-01

Data are presented from an array of single-turn loop probes newly installed on the inner wall of C-Mod, directly opposite one of the two fast-wave antennas. The 8-loop array extends 32^circ in the toroidal direction at the midplane and can distinguish electromagnetic from electrostatic modes. Data are acquired by 1GHz digitizer, spectrum analyzer, and RF detector circuit. Phase measurements during different heating scenarios show evidence of both standing and travelling waves. The measurement of toroidal mode number N_tor (conserved under the assumption of axisymmetry) is used to guide the toroidal full-wave code TORIC(Brambilla, M., IPP Report 5/66, February 1996). Amplitude measurements show modulation both by Type III ELMs and sawteeth; the observed sawtooth modulation may be interpreted as due to changes in central absorption. The amplitude of tildeB_tor measured at the inner wall is compared to the prediction of TORIC.

First Results From the Alcator C-Mod Lower Hybrid Experiment

NASA Astrophysics Data System (ADS)

Parker, Ronald; Bernabei, Stefano; Grimes, Montgomery; Hosea, Joel; Johnson, David; Wilson, Randy

2005-10-01

A lower hybrid system operating at 4.6 GHz and capable of 3 MW source power has been installed on Alcator C-Mod. The grill facing the plasma consists of 4 rows of 24 waveguides. Electronic control of the amplitude and phase of the 12 klystrons supplying the RF power enables the launcher's n|| spectrum to be dynamically controlled over a wide range with a time response of 1 ms. Since the deposition of current depends on n|| as well as the temperature profile, the spatial distribution of the driven current can be varied with the same time response. Detection of fast electron Bremsstrahlung is the primary means of monitoring the driven current profile. Initial measurements at the 100 kW power level show that reflection coefficients as low as 7% are obtained at optimal phasing and density at the grill mouth. Comparison of these results with modeling predictions will be presented in a companion paper.

Efficient design and verification of diagnostics for impurity transport experiments.

PubMed

Chilenski, M A; Greenwald, M J; Marzouk, Y M; Rice, J E; White, A E

2018-01-01

Recent attempts to measure impurity transport in Alcator C-Mod using an x-ray imaging crystal spectrometer and laser blow-off impurity injector have failed to yield unique reconstructions of the transport coefficient profiles. This paper presents a fast, linearized model which was constructed to estimate diagnostic requirements for impurity transport experiments. The analysis shows that the spectroscopic diagnostics on Alcator C-Mod should be capable of inferring simple profiles of impurity diffusion D Z and convection V Z accurate to better than ±10% uncertainty, suggesting that the failure to infer unique D Z and V Z from experimental data is attributable to an inadequate analysis procedure rather than the result of insufficient diagnostics. Furthermore, the analysis reveals that even a modest spatial resolution can overcome a low time resolution. This approach can be adapted to design and verify diagnostics for transport experiments on any magnetic confinement device.

Molybdenum emission from impurity-induced m= 1 snake-modes on the Alcator C-Mod tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delgado-Aparicio, L.; MIT - Plasma Science and Fusion Center, Cambridge, Massachusetts 02139; Bitter, M.

2012-10-15

A suite of novel high-resolution spectroscopic imaging diagnostics has facilitated the identification and localization of molybdenum impurities as the main species during the formation and lifetime of m= 1 impurity-induced snake-modes on Alcator C-Mod. Such measurements made it possible to infer, for the first time, the perturbed radiated power density profiles from which the impurity density can be deduced.

Performance of spectral MSE diagnostic on C-Mod and ITER

NASA Astrophysics Data System (ADS)

Liao, Ken; Rowan, William; Mumgaard, Robert; Granetz, Robert; Scott, Steve; Marchuk, Oleksandr; Ralchenko, Yuri; Alcator C-Mod Team

2015-11-01

Magnetic field was measured on Alcator C-mod by applying spectral Motional Stark Effect techniques based on line shift (MSE-LS) and line ratio (MSE-LR) to the H-alpha emission spectrum of the diagnostic neutral beam atoms. The high field of Alcator C-mod allows measurements to be made at close to ITER values of Stark splitting (~ Bv⊥) with similar background levels to those expected for ITER. Accurate modeling of the spectrum requires a non-statistical, collisional-radiative analysis of the excited beam population and quadratic and Zeeman corrections to the Stark shift. A detailed synthetic diagnostic was developed and used to estimate the performance of the diagnostic at C-Mod and ITER parameters. Our analysis includes the sensitivity to view and beam geometry, aperture and divergence broadening, magnetic field, pixel size, background noise, and signal levels. Analysis of preliminary experiments agree with Kinetic+(polarization)MSE EFIT within ~2° in pitch angle and simulations predict uncertainties of 20 mT in | B | and <2° in pitch angle. This material is based upon work supported by the U.S. Department of Energy Office of Science, Office of Fusion Energy Sciences under Award Number DE-FG03-96ER-54373 and DE-FC02-99ER54512.

Boundary plasma heat flux width measurements for poloidal magnetic fields above 1 Tesla in the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, Dan; Labombard, Brian; Kuang, Adam; Terry, Jim; Alcator C-Mod Team

2017-10-01

The boundary heat flux width, along with the total power flowing into the boundary, sets the power exhaust challenge for tokamaks. A multi-machine boundary heat flux width database found that the heat flux width in H-modes scaled inversely with poloidal magnetic field (Bp) and was independent of machine size. The maximum Bp in the database was 0.8 T, whereas the ITER 15 MA, Q =10 scenario will be 1.2 T. New measurements of the boundary heat flux width in Alcator C-Mod extend the international database to plasmas with Bp up to 1.3 T. C-Mod was the only experiment able to operate at ITER-level Bp. These new measurements are from over 300 plasma shots in L-, I-, and EDA H-modes spanning essentially the whole operating space in C-Mod. We find that the inverse-Bp dependence of the heat flux width in H-modes continues to ITER-level Bp, further reinforcing the empirical projection of 500 μm heat flux width for ITER. We find 50% scatter around the inverse-Bp scaling and are searching for the `hidden variables' causing this scatter. Supported by USDoE award DE-FC02-99ER54512.

Flux-driven turbulence GDB simulations of the IWL Alcator C-Mod L-mode edge compared with experiment

NASA Astrophysics Data System (ADS)

Francisquez, Manaure; Zhu, Ben; Rogers, Barrett

2017-10-01

Prior to predicting confinement regime transitions in tokamaks one may need an accurate description of L-mode profiles and turbulence properties. These features determine the heat-flux width upon which wall integrity depends, a topic of major interest for research aid to ITER. To this end our work uses the GDB model to simulate the Alcator C-Mod edge and contributes support for its use in studying critical edge phenomena in current and future tokamaks. We carried out 3D electromagnetic flux-driven two-fluid turbulence simulations of inner wall limited (IWL) C-Mod shots spanning closed and open flux surfaces. These simulations are compared with gas puff imaging (GPI) and mirror Langmuir probe (MLP) data, examining global features and statistical properties of turbulent dynamics. GDB reproduces important qualitative aspects of the C-Mod edge regarding global density and temperature profiles, within reasonable margins, and though the turbulence statistics of the simulated turbulence follow similar quantitative trends questions remain about the code's difficulty in exactly predicting quantities like the autocorrelation time A proposed breakpoint in the near SOL pressure and the posited separation between drift and ballooning dynamics it represents are examined This work was supported by DOE-SC-0010508. This research used resources of the National Energy Research Scientific Computing Center (NERSC).

Experiments and Simulations of ITER-like Plasmas in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

.R. Wilson, C.E. Kessel, S. Wolfe, I.H. Hutchinson, P. Bonoli, C. Fiore, A.E. Hubbard, J. Hughes, Y. Lin, Y. Ma, D. Mikkelsen, M. Reinke, S. Scott, A.C.C. Sips, S. Wukitch and the C-Mod Team

Alcator C-Mod is performing ITER-like experiments to benchmark and verify projections to 15 MA ELMy H-mode Inductive ITER discharges. The main focus has been on the transient ramp phases. The plasma current in C-Mod is 1.3 MA and toroidal field is 5.4 T. Both Ohmic and ion cyclotron (ICRF) heated discharges are examined. Plasma current rampup experiments have demonstrated that (ICRF and LH) heating in the rise phase can save voltseconds (V-s), as was predicted for ITER by simulations, but showed that the ICRF had no effect on the current profile versus Ohmic discharges. Rampdown experiments show an overcurrent inmore » the Ohmic coil (OH) at the H to L transition, which can be mitigated by remaining in H-mode into the rampdown. Experiments have shown that when the EDA H-mode is preserved well into the rampdown phase, the density and temperature pedestal heights decrease during the plasma current rampdown. Simulations of the full C-Mod discharges have been done with the Tokamak Simulation Code (TSC) and the Coppi-Tang energy transport model is used with modified settings to provide the best fit to the experimental electron temperature profile. Other transport models have been examined also. __________________________________________________« less

Appendix C : the Noise Exposure Model (MOD 4)

DOT National Transportation Integrated Search

1971-08-01

The purpose of this report is threefold: 1. To record the results of efforts at the Transportaiton Systems Center to refine and expand the Noise Exposure Model, which have specifically resulted in the MOD 4 ver described herein; 2. To serve as an Use...

Cloud-based uniform ChIP-Seq processing tools for modENCODE and ENCODE.

PubMed

Trinh, Quang M; Jen, Fei-Yang Arthur; Zhou, Ziru; Chu, Kar Ming; Perry, Marc D; Kephart, Ellen T; Contrino, Sergio; Ruzanov, Peter; Stein, Lincoln D

2013-07-22

Funded by the National Institutes of Health (NIH), the aim of the Model Organism ENCyclopedia of DNA Elements (modENCODE) project is to provide the biological research community with a comprehensive encyclopedia of functional genomic elements for both model organisms C. elegans (worm) and D. melanogaster (fly). With a total size of just under 10 terabytes of data collected and released to the public, one of the challenges faced by researchers is to extract biologically meaningful knowledge from this large data set. While the basic quality control, pre-processing, and analysis of the data has already been performed by members of the modENCODE consortium, many researchers will wish to reinterpret the data set using modifications and enhancements of the original protocols, or combine modENCODE data with other data sets. Unfortunately this can be a time consuming and logistically challenging proposition. In recognition of this challenge, the modENCODE DCC has released uniform computing resources for analyzing modENCODE data on Galaxy (https://github.com/modENCODE-DCC/Galaxy), on the public Amazon Cloud (http://aws.amazon.com), and on the private Bionimbus Cloud for genomic research (http://www.bionimbus.org). In particular, we have released Galaxy workflows for interpreting ChIP-seq data which use the same quality control (QC) and peak calling standards adopted by the modENCODE and ENCODE communities. For convenience of use, we have created Amazon and Bionimbus Cloud machine images containing Galaxy along with all the modENCODE data, software and other dependencies. Using these resources provides a framework for running consistent and reproducible analyses on modENCODE data, ultimately allowing researchers to use more of their time using modENCODE data, and less time moving it around.

Cloud-based uniform ChIP-Seq processing tools for modENCODE and ENCODE

PubMed Central

2013-01-01

Background Funded by the National Institutes of Health (NIH), the aim of the Model Organism ENCyclopedia of DNA Elements (modENCODE) project is to provide the biological research community with a comprehensive encyclopedia of functional genomic elements for both model organisms C. elegans (worm) and D. melanogaster (fly). With a total size of just under 10 terabytes of data collected and released to the public, one of the challenges faced by researchers is to extract biologically meaningful knowledge from this large data set. While the basic quality control, pre-processing, and analysis of the data has already been performed by members of the modENCODE consortium, many researchers will wish to reinterpret the data set using modifications and enhancements of the original protocols, or combine modENCODE data with other data sets. Unfortunately this can be a time consuming and logistically challenging proposition. Results In recognition of this challenge, the modENCODE DCC has released uniform computing resources for analyzing modENCODE data on Galaxy (https://github.com/modENCODE-DCC/Galaxy), on the public Amazon Cloud (http://aws.amazon.com), and on the private Bionimbus Cloud for genomic research (http://www.bionimbus.org). In particular, we have released Galaxy workflows for interpreting ChIP-seq data which use the same quality control (QC) and peak calling standards adopted by the modENCODE and ENCODE communities. For convenience of use, we have created Amazon and Bionimbus Cloud machine images containing Galaxy along with all the modENCODE data, software and other dependencies. Conclusions Using these resources provides a framework for running consistent and reproducible analyses on modENCODE data, ultimately allowing researchers to use more of their time using modENCODE data, and less time moving it around. PMID:23875683

Evidence for Chaotic Edge Turbulence in the Alcator C-Mod Tokamak

NASA Astrophysics Data System (ADS)

Zhu, Ziyan; White, Anne; Carter, Troy; Terry, Jim; Baek, Seung Gyou

2016-10-01

Turbulence greatly reduces the confinement time of magnetic-confined plasmas; understanding the nature of this turbulence and the associated transport is therefore of great importance. This research seeks to establish whether turbulent fluctuations in Alcator C-Mod are chaotic or stochastic. This has an important impact on transport caused by turbulence in C-Mod: stochastic fluctuations sample all of phase space and can lead to diffusive transport, whereas chaotic fluctuations live in a restricted phase space (e.g. on attractors) and a diffusive description may not be valid. By analyzing the time series from an O-Mode reflectometer, turbulent edge density fluctuations in Ohmic plasmas and L-mode plasmas in the Alcator C-Mod tokamak are shown to be chaotic. Supporting evidence for chaos in the edge region includes: the observation of an exponential power spectra (which is associated with Lorentzian-shaped pulses in the time series) and the location of the signal in the Complexity-Entropy plane (C-H plane) and its corresponding Brandt-Pompe (BP) probability distribution. These analysis techniques will be briefly introduced along with a discussion of the analysis results. Different diagnostic techniques, such as Gas Puff Imaging (GPI), could be used to confirm the results. Work supported by the U.S. Department of Energy Office of Science under Agreement DE-FC02-99ER54512 and DE-FC02-07ER54918:011.

An in situ accelerator-based diagnostic for plasma-material interactions science on magnetic fusion devices.

PubMed

Hartwig, Zachary S; Barnard, Harold S; Lanza, Richard C; Sorbom, Brandon N; Stahle, Peter W; Whyte, Dennis G

2013-12-01

This paper presents a novel particle accelerator-based diagnostic that nondestructively measures the evolution of material surface compositions inside magnetic fusion devices. The diagnostic's purpose is to contribute to an integrated understanding of plasma-material interactions in magnetic fusion, which is severely hindered by a dearth of in situ material surface diagnosis. The diagnostic aims to remotely generate isotopic concentration maps on a plasma shot-to-shot timescale that cover a large fraction of the plasma-facing surface inside of a magnetic fusion device without the need for vacuum breaks or physical access to the material surfaces. Our instrument uses a compact (~1 m), high-current (~1 milliamp) radio-frequency quadrupole accelerator to inject 0.9 MeV deuterons into the Alcator C-Mod tokamak at MIT. We control the tokamak magnetic fields--in between plasma shots--to steer the deuterons to material surfaces where the deuterons cause high-Q nuclear reactions with low-Z isotopes ~5 μm into the material. The induced neutrons and gamma rays are measured with scintillation detectors; energy spectra analysis provides quantitative reconstruction of surface compositions. An overview of the diagnostic technique, known as accelerator-based in situ materials surveillance (AIMS), and the first AIMS diagnostic on the Alcator C-Mod tokamak is given. Experimental validation is shown to demonstrate that an optimized deuteron beam is injected into the tokamak, that low-Z isotopes such as deuterium and boron can be quantified on the material surfaces, and that magnetic steering provides access to different measurement locations. The first AIMS analysis, which measures the relative change in deuterium at a single surface location at the end of the Alcator C-Mod FY2012 plasma campaign, is also presented.

Metallo-organic decomposition films

NASA Technical Reports Server (NTRS)

Gallagher, B. D.

1985-01-01

A summary of metallo-organic deposition (MOD) films for solar cells was presented. The MOD materials are metal ions compounded with organic radicals. The technology is evolving quickly for solar cell metallization. Silver compounds, especially silver neodecanoate, were developed which can be applied by thick-film screening, ink-jet printing, spin-on, spray, or dip methods. Some of the advantages of MOD are: high uniform metal content, lower firing temperatures, decomposition without leaving a carbon deposit or toxic materials, and a film that is stable under ambient conditions. Molecular design criteria were explained along with compounds formulated to date, and the accompanying reactions for these compounds. Phase stability and the other experimental and analytic results of MOD films were presented.

Unit Ministry Team Religious Support to Casualties on the Airland Battlefield

DTIC Science & Technology

1987-10-28

282 Mononucleosis , Mod 283 Hepatitis, Infectious 284 Cholecystitis, Severe 285 Cholecystitis, Mod 286 Pancreatitis Acute, Sev 287 Cirrhosis, Severe...Ministry A-5 APPENDIX B - Methodology B-l APPENDIX C - Modal C-l APPENDIX D - Data D-l Patient Description and Treatment Data D-l Hospital Suamary...Support, AirLand Battla E-l Echelons of Medical Treatment E-3 Mass Casualtias E-5 Evacuation E-5 Madical Regulating E-6 Employment E-7

Mod-2 wind turbine system concept and preliminary design report. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

The configuration development of the MOD-2 wind turbine system is presented. The MOD-2 is design optimized for commercial production rates which, in multi-unit installations, will be integrated into a utility power grid and achieve a cost of electricity at less than 4 cents per kilowatt hour.

Rhabdomyolysis in a patient complicated with hypopituitarism and multiple organ dysfunction syndrome and the literature review.

PubMed

Zhou, Chuan; Lai, Shichao; Xie, Yong; Zhang, Shu; Lu, Yiping

2018-06-07

Muscular symptoms, including stiffness, myalgia, cramps, and fatigue, are present in the majority of the patients with hypopituitarism, adrenal insufficiency and hypothyroidism, but rhabdomyolysis, the rapid breakdown of skeletal muscle, is a rare manifestation. In most patients who develop rhabdomyolysis, precipitating factors, such as strenuous exercise or use of lipid-lowering drugs, can be identified. We report the case of a 23-year-old male with primary hypopituitarism who developed acute renal impairment (AKI) with rhabdomyolysis after strenuous physical activity (push-ups). His blood test confirmed marked hypopituitarism. Severe elevation of serum CK consistent with rhabdomyolysis was noted and an elevated creatinine indicated AKI and multiple organ dysfunction syndrome (MODS). Patient's condition improved significantly after continuous renal replacement therapy (CRRT), glucocorticoid hormone replacement therapy and aggressive hydration. MODS with rhabdomyolysis in patients with hypothyroidism is quite rare and we expect that this case report adds to the existing literature on this subject. We also emphasize that thyroid and adrenal gland status should be evaluated in patients with unexplained AKI, MODS and presenting with the symptoms of muscle involvement. We respectively reviewed 23 patients with hypopituitarism, adrenal Insufficiency and hypothyroidism induced rhabdomyolysis who were involved in the past 40 years relevant literatures. We report a successfully treated case of rhabdomyolysis, which is a rare but potentially serious complication of hypopituitarism. Screening for endocrine abnormality in patients with elevated muscle enzymes should be considered, since an early diagnosis and prompt treatment is essential to prevent rhabdomyolysis and its consequences. Copyright © 2018. Published by Elsevier Inc.

78 FR 58492 - Generator Verification Reliability Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-24

... Control Functions), MOD-027-1 (Verification of Models and Data for Turbine/Governor and Load Control or...), MOD-027-1 (Verification of Models and Data for Turbine/Governor and Load Control or Active Power... Category B and C contingencies, as required by wind generators in Order No. 661, or that those generators...

Effect of partial replacement of alfalfa hay with Moringa species leaves on milk yield and composition of Najdi ewes.

PubMed

Babiker, Elfadıl E; Al Juhaimi, Fahad; Ghafoor, Kashif; Mohamed, H E; Abdoun, Khalid A

2016-10-01

The present study was carried out to investigate changes in milk yield and composition of Najdi ewes fed 25 % Moringa oleifera (MOD) or Moringa peregrina (MPD) leaf diets as a supplement to alfalfa hay diet (AHD). Thirty ewes (average 55 kg, 2 years old) were randomly sorted into three experimental groups with 10 animals each and were fed for a 6-week period with these diets (AHD, MOD, or MPD). Diets dry matter, crude protein, and crude fiber were comparable, while fat, nitrogen-free extract (NFE), neutral detergent fiber (NDF), acid detergent fiber (ADF), metabolizable energy (ME), total phenolic, and antioxidant activity varied (p ≤ 0.05) between the diets. Feeding ewes with MOD increased (p ≤ 0.05) the milk yield compared to those fed AHD while milk composition was similar (p ≤ 0.05) between treatments. The concentration of malondialdehyde (MDA) in the ewes' milk and serum was lower (p ≤ 0.05) for MOD, while the total antioxidant capacity, catalase activity, and vitamin C contents were increased (p ≤ 0.05). The serum cholesterol and glucose of the ewes were lower (p ≤ 0.05) for those fed MOD. Moringa diets increased (p ≤ 0.05) average daily weight gain of lambs compared to those fed alfalfa diets. The results obtained showed that the inclusion of Moringa, especially M. oleifera, in the diet of Najdi ewes can improve milk yield and quality.

How much do different global GPP products agree in distribution and magnitude of GPP extremes?

NASA Astrophysics Data System (ADS)

Kim, S.; Ryu, Y.; Jiang, C.

2016-12-01

To evaluate uncertainty of global Gross Primary Productivity (GPP) extremes, we compare three global GPP datasets derived from different data processing methods (e.g. MPI-BGC: machine-learning, MODIS GPP (MOD17): semi-empirical, Breathing Earth System Simulator (BESS): process based). We preprocess the datasets following the method from Zscheischler et al., (2012) to detect GPP extremes which occur in less than 1% of the number of whole pixels, and to identify 3D-connected spatiotemporal GPP extremes. We firstly analyze global patterns and the magnitude of GPP extremes with MPI-BGC, MOD17, and BESS over 2001-2011. For consistent analysis in the three products, spatial and temporal resolution were set at 50 km and a monthly scale, respectively. Our results indicated that the global patterns of GPP extremes derived from MPI-BGC and BESS agreed with each other by showing hotspots in Northeastern Brazil and Eastern Texas. However, the extreme events detected from MOD17 were concentrated in tropical forests (e.g. Southeast Asia and South America). The amount of GPP reduction caused by climate extremes considerably differed across the products. For example, Russian heatwave in 2010 led to 100 Tg C uncertainty (198.7 Tg C in MPI-BGC, 305.6 Tg C in MOD17, and 237.8 Tg C in BESS). Moreover, the duration of extreme events differ among the three GPP datasets for the Russian heatwave (MPI-BGC: May-Sep, MOD17: Jun-Aug, and BESS: May-Aug). To test whether Sun induced Fluorescence (SiF), a proxy of GPP, can capture GPP extremes, we investigate global distribution of GPP extreme events in BESS, MOD17 and GOME-2 SiF between 2008 and 2014 when SiF data is available. We found that extreme GPP events in GOME-2 SiF and MOD17 appear in tropical forests whereas those in BESS emerged in Northeastern Brazil and Eastern Texas. The GPP extremes by severe 2011 US drought were detected by BESS and MODIS, but not by SiF. Our findings highlight that different GPP datasets could result in varying duration and intensity of GPP extremes and distribution of hotspots, and this study could contribute to quantifying uncertainties in GPP extremes.

Experimental pathways to understand and avoid high-Z impurity contamination from ICRF heating in tokamaks

NASA Astrophysics Data System (ADS)

Reinke, Matthew

2016-10-01

Recent results from Alcator C-Mod and JET demonstrate progress in understanding and mitigating core high-Z impurity contamination linked to ICRF heating in tokamaks with high-Z PFCs. Theory has identified two likely mechanisms: impurity sources due to sputtering enhanced by RF-rectified sheaths and greater cross-field SOL transport due to ExB convective cells. New experiments on Alcator C-Mod and JET demonstrate convective cell transport is likely a sub-dominant effect, despite directly observing ExB flows from rectified RF fields on C-Mod. Trace N2 introduced in the far SOL on field lines connected to and well away from an active ICRF antenna result in similar levels of core nitrogen, indicating local RF-driven transport is weak. This suggests the core high-Z density, nZ,core, is determined by sheath-induced sputtering and RF-independent SOL transport, allowing further reductions through antenna design. ICRF heating on C-Mod uses a unique, field aligned (FAA) and a pair of conventional, toroidally aligned (TAA) antennas. The FAA is designed to reduce rectified voltages relative to the TAA, and the impact of sheath-induced sputtering is explored by observing nZ,core while varying the TAA/FAA heating mix. A reduction of approximately 50% in core high-Z content is seen in L-modes when using the FAA and high-Z sources at the antenna limiter are effectively eliminated, indicating the remaining RF-driven source is away from the limiter. A drop in nZ,core may also be realized by locating the RF antenna on the inboard side where SOL transport aids impurity screening. New C-Mod experiments demonstrate up to a factor of 5 reduction in core nitrogen when N2 is injected on the high-field side as compared to low-field side impurity fueling. Varying the magnetic topology helps to elucidate the SOL transport physics responsible, laying a physics basis for inboard RF antenna placement. This work is supported by U.S. DOE Award DE-FC02-99ER54512, using Alcator C-Mod and carried out within the framework of the EUROfusion Consortium and has received funding from Euratom under Grant Agreement No 633053.

Pavement-Transportation Computer Assisted Structural Engineering (PCASE) Implementation of the Modified Berggren (ModBerg) Equation for Computing the Frost Penetration Depth within Pavement Structures

DTIC Science & Technology

2012-04-01

ER D C/ G SL T R -1 2 -1 5 Pavement -Transportation Computer Assisted Structural Engineering (PCASE) Implementation of the Modified...Berggren (ModBerg) Equation for Computing the Frost Penetration Depth within Pavement Structures G eo te ch n ic al a n d S tr u ct u re s La b or at...April 2012 Pavement -Transportation Computer Assisted Structural Engineering (PCASE) Implementation of the Modified Berggren (ModBerg) Equation for

Brahma regulates a specific trans-splicing event at the mod(mdg4) locus of Drosophila melanogaster

PubMed Central

Yu, Simei; Waldholm, Johan; Böhm, Stefanie; Visa, Neus

2014-01-01

The mod(mdg4) locus of Drosophila melanogaster contains several transcription units encoded on both DNA strands. The mod(mdg4) pre-mRNAs are alternatively spliced, and a very significant fraction of the mature mod(mdg4) mRNAs are formed by trans-splicing. We have studied the transcripts derived from one of the anti-sense regions within the mod(mdg4) locus in order to shed light on the expression of this complex locus. We have characterized the expression of anti-sense mod(mdg4) transcripts in S2 cells, mapped their transcription start sites and cleavage sites, identified and quantified alternatively spliced transcripts, and obtained insight into the regulation of the mod(mdg4) trans-splicing. In a previous study, we had shown that the alternative splicing of some mod(mdg4) transcripts was regulated by Brahma (BRM), the ATPase subunit of the SWI/SNF chromatin-remodeling complex. Here we show, using RNA interference and overexpression of recombinant BRM proteins, that the levels of BRM affect specifically the abundance of a trans-spliced mod(mdg4) mRNA isoform in both S2 cells and larvae. This specific effect on trans-splicing is accompanied by a local increase in the density of RNA polymerase II and by a change in the phosphorylation state of the C-terminal domain of the large subunit of RNA polymerase II. Interestingly, the regulation of the mod(mdg4) splicing by BRM is independent of the ATPase activity of BRM, which suggests that the mechanism by which BRM modulates trans-splicing is independent of its chromatin-remodeling activity. PMID:24526065

An inverse modeling strategy and a computer program to model garnet growth and resorption

NASA Astrophysics Data System (ADS)

Lanari, Pierre; Giuntoli, Francesco

2017-04-01

GrtMod is a computer program that allows numerical simulation of the pressure-temperature (P-T) evolution of garnet porphyroblasts based on the composition of successive growth zones preserved in natural samples. For each garnet growth stage, a new reactive bulk composition is optimized, allowing for resorption and/or fractionation of the previously crystalized garnet. The successive minimizations are performed using a heuristic search method and an objective function that quantify the amount by which the predicted garnet composition deviates from the measured values. The automated strategy of GrtMod includes a two stages optimization and one refinement stage. In this contribution, we will present several application examples. The new strategy provides quantitative estimates of the optimal P-T conditions whereas it was generally derived in a qualitatively way by using garnet isopleth intersections in equilibrium phase diagrams. GrtMod can also be used to model the evolution of the reactive bulk composition along any P-T trajectories. The results for typical MORB and metapelite compositions demonstrate that fractional crystallization models are required to derive accurate P-T information from garnet compositional zoning. GrtMod can also be used to retrieve complex garnet histories involving several stages of resorption. For instance, it has been used to model the P-T condition of garnet growth in grains from the Sesia Zone (Western Alps). The compositional variability of successive growth zones is characterized using standardized X-ray maps and the program XMapTools. Permian garnet cores crystalized under granulite facies conditions (T > 800°C and P = 6 kbar), whereas Alpine garnet rims grew at eclogite facies conditions (650°C and 16 kbar) involving several successive episodes of resorption. The model predicts that up to 50 vol% of garnet was dissolved before a new episode of garnet growth.

Sur la modélisation des supraconducteurs: le "modèle de l'état critique" de bean, en trois dimensions

NASA Astrophysics Data System (ADS)

Bossavit, A.

1994-03-01

La formule (22), p. 386, soit u_x(v) = si|v| < j_c(x); alors; 0; sinon; ρ(x)|v|^2/2, aurait dû être u_x(v) = si|v| < j_c(x); alors; 0; sinon; ρ(x)(|v|^2)/2. La même erreur apparaît dans l'introduction (page 376, une ligne après l'équation (10)) et page 390.

Research on the Superheater Material Properties for USC Boiler with 700°C Steam Parameter

NASA Astrophysics Data System (ADS)

Chongbin, Wang; Xueyuan, Xu; Yufeng, Zhu; Yongqiang, Jin; Hui, Tong; Yu, Wang; Xiaoli, Lu

This paper discusses the materials' properties of superheater for 700°C USC boiler, including Sanicro25, HR6W, 617mod and 740H, and analyzes the range of applicable temperature of superheater made of different tubes, such as T91, T92, Super304H, TP310HCbN, Sanicro25, HR6W, 617Mod and 740H. In addition, some suggestions on the material selection have been proposed.

Validation of TGLF in C-Mod and DIII-D using machine learning and integrated modeling tools

NASA Astrophysics Data System (ADS)

Rodriguez-Fernandez, P.; White, Ae; Cao, Nm; Creely, Aj; Greenwald, Mj; Grierson, Ba; Howard, Nt; Meneghini, O.; Petty, Cc; Rice, Je; Sciortino, F.; Yuan, X.

2017-10-01

Predictive models for steady-state and perturbative transport are necessary to support burning plasma operations. A combination of machine learning algorithms and integrated modeling tools is used to validate TGLF in C-Mod and DIII-D. First, a new code suite, VITALS, is used to compare SAT1 and SAT0 models in C-Mod. VITALS exploits machine learning and optimization algorithms for the validation of transport codes. Unlike SAT0, the SAT1 saturation rule contains a model to capture cross-scale turbulence coupling. Results show that SAT1 agrees better with experiments, further confirming that multi-scale effects are needed to model heat transport in C-Mod L-modes. VITALS will next be used to analyze past data from DIII-D: L-mode ``Shortfall'' plasma and ECH swing experiments. A second code suite, PRIMA, allows for integrated modeling of the plasma response to Laser Blow-Off cold pulses. Preliminary results show that SAT1 qualitatively reproduces the propagation of cold pulses after LBO injections and SAT0 does not, indicating that cross-scale coupling effects play a role in the plasma response. PRIMA will be used to ``predict-first'' cold pulse experiments using the new LBO system at DIII-D, and analyze existing ECH heat pulse data. Work supported by DE-FC02-99ER54512, DE-FC02-04ER54698.

Clinical application of a novel diagnostic scheme including pancreatic β‑cell dysfunction for traumatic multiple organ dysfunction syndrome.

PubMed

Wang, Zhan-Ke; Chen, Rong-Jian; Wang, Shi-Liang; Li, Guang-Wei; Zhu, Zhong-Zhen; Huang, Qiang; Chen, Zi-Li; Chen, Fan-Chang; Deng, Lei; Lan, Xiao-Peng; Hu, Tian

2018-01-01

A novel diagnostic scheme that includes pancreatic β‑cell dysfunction analysis for the diagnosis of traumatic multiple organ dysfunction syndrome (MODS) was investigated to assist in the early diagnosis and detection of MODS. Early intervention and treatment of MODS has been associated with a reduced mortality rate. A total of 2,876 trauma patients (including patients post‑major surgery) were admitted to the intensive care unit of the authors' hospital between December 2010 and December 2015 and enrolled in the present study. There were 205 cases where the patient succumbed to their injuries. In addition to the conventional diagnostic scheme for traumatic MODS, indexes of pancreatic β‑cell dysfunction [fasting blood‑glucose (FBG), homeostatic model assessment‑β and (blood insulin concentration 30 min following glucose loading‑fasting insulin concentration)/(blood glucose concentration 30 min following glucose loading‑FBG concentration)] were included to establish an improved diagnostic scheme for traumatic MODS. The novel scheme was subsequently used in clinical practice alongside the conventional scheme and its effect was evaluated. The novel scheme had a significantly higher positive number of MODS diagnoses for all trauma patients compared with the conventional scheme (12.48 vs. 8.87%; P<0.01). No significant difference was identified in the final percentage of positive of MODS diagnoses for trauma‑associated mortality patients between the novel (88.30%) and the conventional scheme (86.34%). The novel scheme had a significantly higher positive number of MODS diagnoses for trauma‑associated mortality patients 3 days prior to patients succumbing to MODS compared with the conventional scheme (80.98 vs. 64.39%; P<0.01). The consensus of the MODS diagnosis of all trauma patients between the novel scheme and the conventional scheme was 100%; however, out of the patients diagnosed as positive by novel scheme 71.03% were positive by the conventional scheme. The consensus between the final MODS diagnosis and the MODS diagnosis 3 days prior to patients succumbing to their injuries between the novel scheme and the conventional scheme was 100%; however, out of the patients diagnosed as positive by novel scheme 97.79 were positive by the conventional scheme of the 205 patients who succumbed to MODS and out of the patients diagnosed as positive for MODS by novel scheme 3 days prior to succumbing, 79.52% were positive by the conventional scheme. The results of the present study demonstrated that the novel diagnostic scheme using the relevant indexes of pancreatic β‑cell dysfunction for diagnosis of traumatic MODS, was able to diagnose MODS early without excessively extending the diagnostic scope. Its clinical application should be promoted.

Diagnosis of Pulmonary Tuberculosis in HIV-Positive Patients by Microscopic Observation Drug Susceptibility Assay ▿

PubMed Central

Ha, Dang Thi Minh; Lan, Nguyen Thi Ngoc; Kiet, Vo Sy; Wolbers, Marcel; Hang, Hoang Thi Thanh; Day, Jeremy; Hien, Nguyen Quang; Tien, Nguyen Anh; An, Pham Thuy; Anh, Truong Thi; Oanh, Do Thi Tuong; Hoa, Chau Luong; Chau, Nguyen Thi Minh; Hai, Nguyen Ngoc; Binh, Ngo Thanh; Ngoc, Le Hong; Phuong, Doan Thanh; Quyet, Tran Van; Tuyen, Nguyen Thi Bich; Ha, Vo Thi; Nho, Nguyen Thi; Hoa, Dai Viet; Anh, Phan Thi Hoang; Dung, Nguyen Huy; Farrar, Jeremy; Caws, Maxine

2010-01-01

The microscopic observation drug susceptibility assay (MODS) is a novel and promising test for the early diagnosis of tuberculosis (TB). We evaluated the MODS assay for the early diagnosis of TB in HIV-positive patients presenting to Pham Ngoc Thach Hospital for Tuberculosis and Lung Diseases in southern Vietnam. A total of 738 consecutive sputum samples collected from 307 HIV-positive individuals suspected of TB were tested by smear, MODS, and the mycobacteria growth indicator tube method (MGIT). The diagnostic sensitivity and specificity of MODS compared to the microbiological gold standard (either smear or MGIT) were 87 and 93%, respectively. The sensitivities of smear, MODS, and MGIT were 57, 71, and 75%, respectively, against clinical gold standard (MODS versus smear, P < 0.001; MODS versus MGIT, P = 0.03). The clinical gold standard was defined as patients who had a clinical examination and treatment consistent with TB, with or without microbiological confirmation. For the diagnosis of smear-negative patients, the sensitivities of MODS and MGIT were 38 and 45%, respectively (P = 0.08). The median times to detection using MODS and MGIT were 8 and 11 days, respectively, and they were 11 and 17 days, respectively, for smear-negative samples. The original bacterial/fungal contamination rate of MODS was 1.1%, while it was 2.6% for MGIT. The cross-contamination rate of MODS was 4.7%. In conclusion, MODS is a sensitive, specific, and rapid test that is appropriate for the detection of HIV-associated TB; its cost and ease of use make it particularly useful in resource-limited settings. PMID:20926704

R-modafinil attenuates nicotine-taking and nicotine-seeking behavior in alcohol-preferring rats.

PubMed

Wang, Xiao-Fei; Bi, Guo-Hua; He, Yi; Yang, Hong-Ju; Gao, Jun-Tao; Okunola-Bakare, Oluyomi M; Slack, Rachel D; Gardner, Eliot L; Xi, Zheng-Xiong; Newman, Amy Hauck

2015-06-01

(±)-Modafinil (MOD) is used clinically for the treatment of sleep disorders and has been investigated as a potential medication for the treatment of psychostimulant addiction. However, the therapeutic efficacy of (±)-MOD for addiction is inconclusive. Herein we used animal models of self-administration and in vivo microdialysis to study the pharmacological actions of R-modafinil (R-MOD) and S-modafinil (S-MOD) on nicotine-taking and nicotine-seeking behavior, and mechanisms underlying such actions. We found that R-MOD is more potent and effective than S-MOD in attenuating nicotine self-administration in Long-Evans rats. As Long-Evans rats did not show a robust reinstatement response to nicotine, we used alcohol-preferring rats (P-rats) that display much higher reinstatement responses to nicotine than Long-Evans rats. We found that R-MOD significantly inhibited intravenous nicotine self-administration, nicotine-induced reinstatement, and nicotine-associated cue-induced drug-seeking behavior in P-rats. R-MOD alone neither sustained self-administration in P-rats previously self-administering nicotine nor reinstated extinguished nicotine-seeking behavior. The in vivo brain microdialysis assays demonstrated that R-MOD alone produced a slow-onset moderate increase in extracellular DA. Pretreatment with R-MOD dose-dependently blocked nicotine-induced dopamine (DA) release in the nucleus accumbens (NAc) in both naive and nicotine self-administrating rats, suggesting a DA-dependent mechanism underlying mitigation of nicotine's effects. In conclusion, the present findings support further investigation of R-MOD for treatment of nicotine dependence in humans.

R-Modafinil Attenuates Nicotine-Taking and Nicotine-Seeking Behavior in Alcohol-Preferring Rats

PubMed Central

Wang, Xiao-Fei; Bi, Guo-Hua; He, Yi; Yang, Hong-Ju; Gao, Jun-Tao; Okunola-Bakare, Oluyomi M; Slack, Rachel D; Gardner, Eliot L; Xi, Zheng-Xiong; Newman, Amy Hauck

2015-01-01

(±)-Modafinil (MOD) is used clinically for the treatment of sleep disorders and has been investigated as a potential medication for the treatment of psychostimulant addiction. However, the therapeutic efficacy of (±)-MOD for addiction is inconclusive. Herein we used animal models of self-administration and in vivo microdialysis to study the pharmacological actions of R-modafinil (R-MOD) and S-modafinil (S-MOD) on nicotine-taking and nicotine-seeking behavior, and mechanisms underlying such actions. We found that R-MOD is more potent and effective than S-MOD in attenuating nicotine self-administration in Long–Evans rats. As Long–Evans rats did not show a robust reinstatement response to nicotine, we used alcohol-preferring rats (P-rats) that display much higher reinstatement responses to nicotine than Long–Evans rats. We found that R-MOD significantly inhibited intravenous nicotine self-administration, nicotine-induced reinstatement, and nicotine-associated cue-induced drug-seeking behavior in P-rats. R-MOD alone neither sustained self-administration in P-rats previously self-administering nicotine nor reinstated extinguished nicotine-seeking behavior. The in vivo brain microdialysis assays demonstrated that R-MOD alone produced a slow-onset moderate increase in extracellular DA. Pretreatment with R-MOD dose-dependently blocked nicotine-induced dopamine (DA) release in the nucleus accumbens (NAc) in both naive and nicotine self-administrating rats, suggesting a DA-dependent mechanism underlying mitigation of nicotine's effects. In conclusion, the present findings support further investigation of R-MOD for treatment of nicotine dependence in humans. PMID:25613829

Development of an automated MODS plate reader to detect early growth of Mycobacterium tuberculosis.

PubMed

Comina, G; Mendoza, D; Velazco, A; Coronel, J; Sheen, P; Gilman, R H; Moore, D A J; Zimic, M

2011-06-01

In this work, an automated microscopic observation drug susceptibility (MODS) plate reader has been developed. The reader automatically handles MODS plates and after autofocussing digital images are acquired of the characteristic microscopic cording structures of Mycobacterium tuberculosis, which are the identification method utilized in the MODS technique to detect tuberculosis and multidrug resistant tuberculosis. In conventional MODS, trained technicians manually move the MODS plate on the stage of an inverted microscope while trying to locate and focus upon the characteristic microscopic cording colonies. In centres with high tuberculosis diagnostic demand, sufficient time may not be available to adequately examine all cultures. An automated reader would reduce labour time and the handling of M. tuberculosis cultures by laboratory personnel. Two hundred MODS culture images (100 from tuberculosis positive and 100 from tuberculosis negative sputum samples confirmed by a standard MODS reading using a commercial microscope) were acquired randomly using the automated MODS plate reader. A specialist analysed these digital images with the help of a personal computer and designated them as M. tuberculosis present or absent. The specialist considered four images insufficiently clear to permit a definitive reading. The readings from the 196 valid images resulted in a 100% agreement with the conventional nonautomated standard reading. The automated MODS plate reader combined with open-source MODS pattern recognition software provides a novel platform for high throughput automated tuberculosis diagnosis. © 2011 The Authors Journal of Microscopy © 2011 Royal Microscopical Society.

75 FR 26057 - Mandatory Reliability Standards for the Calculation of Available Transfer Capability, Capacity...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-11

... Requirement R3.1 of MOD-001-1. C. Benchmarking 14. In the Final Rule, the Commission directed the ERO to develop benchmarking and updating requirements for the MOD Reliability Standards to measure modeled... requirements should specify the frequency for benchmarking and updating the available transfer and flowgate...

Prise en compte des ``courants de London'' dans la modélisation des supraconducteurs

NASA Astrophysics Data System (ADS)

Bossavit, Alain

1997-10-01

A model is given, in variational form, in which volumic “Bean currents”, ruled by Bean's law, and surface “London currents” coexist. This macroscopic model generalizes Bean's one, by appending to the critical density j_c a second parameter, with the dimension of a length, similar to London's depth λ. The one-dimensional version of the model is investigated, in order to link this parameter with the standard observable H-M characteristics On propose un modèle, sous forme variationnelle, associant des “courants de Bean” volumiques, décrits par la loi de Bean, et des “courants de London”, surfaciques. Ce modèle macroscopique généralise celui de Bean, caractérisé par le courant critique j_c, et fait intervenir un second paramètre, homogène à une longueur, analogue au λ de London. La version unidimensionnelle du modèle est étudiée en détail de manière à relier ce paramètre à l'observation des caractéristiques H-M usuelles.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Richey, A.; Farrell, R.; Riecke, G.; Ernst, W.; Howarth, R.; Cronin, M.; Simetkosky, M.; Smith, G.; Meacher, J.

1985-01-01

Development test activities on Mod I engines directed toward evaluating technologies for potential inclusion in the Mod II engine are summarized. Activities covered include: test of a 12-tube combustion gas recirculation combustor; manufacture and flow-distribution test of a two-manifold annular heater head; piston rod/piston base joint; single-solid piston rings; and a digital air/fuel concept. Also summarized are results of a formal assessment of candidate technologies for the Mod II engine, and preliminary design work for the Mod II. The overall program philosophy weight is outlined, and data and test results are presented.

Multimission Modular Spacecraft Ground Support Software System (MMS/GSSS) state-of-the-art computer systems/ compatibility study

NASA Technical Reports Server (NTRS)

1980-01-01

The compatibility of the Multimission Modular Spacecraft (MMS) Ground Support Software System (GSSS), currently operational on a ModComp IV/35, with the VAX 11/780 system is discussed. The compatibility is examined in various key areas of the GSSS through the results of in depth testing performed on the VAX 11/780 and ModComp IV/35 systems. The compatibility of the GSSS with the ModComp CLASSIC is presented based upon projections from ModComp supplied literature.

Highly Reactive Thiol-Norbornene Photo-Click Hydrogels: Toward Improved Processability.

PubMed

Van Hoorick, Jasper; Gruber, Peter; Markovic, Marica; Rollot, Mélanie; Graulus, Geert-Jan; Vagenende, Maxime; Tromayer, Maximilian; Van Erps, Jürgen; Thienpont, Hugo; Martins, José C; Baudis, Stefan; Ovsianikov, Aleksandr; Dubruel, Peter; Van Vlierberghe, Sandra

2018-06-10

In the present work, gelatin type B is modified with highly reactive norbornene functionalities (Gel-NB) following a one-pot synthesis approach to enable subsequent thiol-ene photo-click crosslinking. The modification strategy displays close control over the amount of introduced functionalities. Additionally, Gel-NB exhibits considerably improved processing capabilities in terms of two-photon polymerization when benchmarked to earlier-reported crosslinkable gelatin derivatives (e.g., gelatin-methacrylamide (Gel-MOD) and gelatin-methacrylamide-aminoethylmethacrylate (Gel-MOD-AEMA)). The improvement is especially apparent in terms of minimally required laser power (20 mW vs ≥60 mW (Gel-MOD) vs ≥40 mW (Gel-MOD-AEMA) at 100 mm s -1 scan speed) and processable concentration range (≥5 w/v% vs ≥10 w/v% (Gel-MOD/Gel-MOD-AEMA)). Furthermore, the proposed functionalization scheme maintains the excellent biocompatibility and cell interactivity of gelatin. Additionally, the norbornene functionalities have potential for straightforward postprocessing "thiol-ene" surface grafting of active molecules. As a consequence, a very promising material toward tissue engineering applications and more specifically, biofabrication, is presented. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

VarMod: modelling the functional effects of non-synonymous variants

PubMed Central

Pappalardo, Morena; Wass, Mark N.

2014-01-01

Unravelling the genotype–phenotype relationship in humans remains a challenging task in genomics studies. Recent advances in sequencing technologies mean there are now thousands of sequenced human genomes, revealing millions of single nucleotide variants (SNVs). For non-synonymous SNVs present in proteins the difficulties of the problem lie in first identifying those nsSNVs that result in a functional change in the protein among the many non-functional variants and in turn linking this functional change to phenotype. Here we present VarMod (Variant Modeller) a method that utilises both protein sequence and structural features to predict nsSNVs that alter protein function. VarMod develops recent observations that functional nsSNVs are enriched at protein–protein interfaces and protein–ligand binding sites and uses these characteristics to make predictions. In benchmarking on a set of nearly 3000 nsSNVs VarMod performance is comparable to an existing state of the art method. The VarMod web server provides extensive resources to investigate the sequence and structural features associated with the predictions including visualisation of protein models and complexes via an interactive JSmol molecular viewer. VarMod is available for use at http://www.wasslab.org/varmod. PMID:24906884

On the ρ ∗ scaling of intrinsic rotation in C-Mod plasmas with edge transport barriers

NASA Astrophysics Data System (ADS)

Rice, J. E.; Hughes, J. W.; Diamond, P. H.; Cao, N.; Chilenski, M. A.; Hubbard, A. E.; Irby, J. H.; Kosuga, Y.; Lin, Y.; Metcalf, I. W.; Reinke, M. L.; Tolman, E. A.; Victora, M. M.; Wolfe, S. M.; Wukitch, S. J.

2017-11-01

Changes in the core intrinsic toroidal rotation velocity following L- to H- and L- to I-mode transitions have been investigated in Alcator C-Mod tokamak plasmas. The magnitude of the co-current rotation increments is found to increase with the pedestal temperature gradient and q95 , and to decrease with toroidal magnetic field. These results are captured quantitatively by a model of fluctuation entropy balance which gives the Mach number Mi \\cong ρ _*/2 L_s/LT ∼ \

Cerebral Palsy and Growth Failure at 6 to 7 Years

PubMed Central

Stephens, Bonnie E.; McDonald, Scott A.; Ehrenkranz, Richard A.; Laptook, Abbot R.; Pappas, Athina; Hintz, Susan R.; Shankaran, Seetha; Higgins, Rosemary D.; Das, Abhik

2013-01-01

OBJECTIVE: To evaluate the association between severity of cerebral palsy (CP) and growth to 6 to 7 years of age among children with moderate to severe (Mod/Sev) hypoxic ischemic encephalopathy (HIE). It was hypothesized that children with Mod/Sev CP would have poorer growth, lower cognitive scores, and increased rehospitalization rates compared with children with no CP (No CP). METHODS: Among 115 of 122 surviving children followed in the hypothermia trial for neonatal HIE, growth parameters and neurodevelopmental status at 18 to 22 months and 6 to 7 years were available. Group comparisons (Mod/Sev CP and No CP) with unadjusted and adjusted analyses for growth <10th percentile and z scores by using Fisher’s exact tests and regression modeling were conducted. RESULTS: Children with Mod/Sev CP had high rates of slow growth and cognitive and motor impairment and rehospitalizations at 18 to 22 months and 6 to 7 years. At 6 to 7 years of age, children with Mod/Sev CP had increased rates of growth parameters <10th percentile compared with those with No CP (weight, 57% vs 3%; height, 70% vs 2%; and head circumference, 82% vs 13%; P < .0001). Increasing severity of slow growth was associated with increasing age (P < .04 for weight, P < .001 for length, and P < .0001 for head circumference). Gastrostomy feeds were associated with better growth. CONCLUSIONS: Term children with HIE who develop Mod/Sev CP have high and increasing rates of growth <10th percentile by 6 to 7 years of age. These findings support the need for close medical and nutrition management of children with HIE who develop CP. PMID:24019415

[Diagnostic value of integral scoring systems in assessing the severity of acute pancreatitis and patient's condition].

PubMed

Vinnik, Y S; Dunaevskaya, S S; Antufrieva, D A

2015-01-01

The aim of the study was to evaluate the diagnostic value of specific and nonspecific scoring systems Tolstoy-Krasnogorov score, Ranson, BISAP, Glasgow, MODS 2, APACHE II and CTSI, which used at urgent pancreatology for estimation the severity of acute pancreatitis and status of patient. 1550 case reports of patients which had inpatient surgical treatment at Road clinical hospital at the station Krasnoyarsk from 2009 till 2013 were analyzed. Diagnosis of severe acute pancreatitis and its complications were determined based on anamnestic data, physical exami- nation, clinical indexes, ultrasonic examination and computed tomography angiography. Specific and nonspecific scores (scoring system of estimation by Tolstoy-Krasnogorov, Ranson, Glasgow, BISAP, MODS 2, APACHE II, CTSI) were used for estimation the severity of acute pancreatitis and patient's general condition. Effectiveness of these scoring systems was determined based on some parameters: accuracy (Ac), sensitivity (Se), specificity (Sp), positive predictive value (PPV) and negative predictive value (NPV). Most valuables score for estimation of acute pancreatitis's severity is BISAP (Se--98.10%), for estimation of organ failure--MODS 2 (Sp--100%, PPV--100%) and APACHE II (Sp--100%, PPV--100%), for detection of pancreatonecrosis sings--CTSI (Sp--100%, NPV--100%), for estimation of need for intensive care--MODS 2 (Sp--100%, PPV--100%, NPV--96.29%) and APACHE II (Sp--100%, PPV--100%, NPV--97.21%), for prediction of lethality--MODS 2 (Se-- 100%, Sp--98.14%, NPV--100%) and APACHE II (Se--95.00%, NPV-.99.86%). Most effective scores for estimation of acute pancreatitis's severity are Score of estimation by Tolstoy-Krasnogorov, Ranson, Glasgow and BISAP Scoring systems MODS 2, APACHE I high specificity and positive predictive value allow using it at clinical practice.

SOL Thermal Instability due to Radial Blob Convection

NASA Astrophysics Data System (ADS)

D'Ippolito, D. A.

2005-10-01

C-Mod datafootnotetextM. Greenwald, Plasma Phys. Contr. Fusion 44, R27 (2002). suggests a density limit when rapid perpendicular convection dominates SOL heat transport. This is supported by a recent analysisfootnotetextD.A. Russell et al., Phys. Rev. Lett. 93, 265001 (2004). of BOUT code turbulence simulations, which shows that rapid outwards convection of plasma by turbulent blobs is enhanced when the X-point collisionality is large, resulting in a synergistic effect between blob convection and X-point cooling. This work motivates the present analysis of SOL thermal equilibrium and instability including an RX-regime modelfootnotetextJ.R. Myra and D.A. D'Ippolito, Lodestar Report LRC-05-105 (2005). of blob particle and heat transport. Two-point (midplane, X-point) SOL thermal equilibrium and stability models are considered including both two-field (T) and four-field (n,T) treatments. The conditions under which loss of thermal equilibrium or thermal instabilities occur are established, and relations to the C-Mod data are described.

Low Density ITB Studies Using the Upgraded C-Mod Reflectometry System

NASA Astrophysics Data System (ADS)

Dominguez, A.; Edlund, E.; Fiore, C. L.; Lin, L.; Marmar, E. S.; Snipes, J. A.; Porkolab, M.; Kramer, G. J.; Rowan, W. L.

2007-11-01

The Alcator C-Mod reflectometry system was recently upgraded in two ways: The low frequency channels were changed from amplitude modulation - in which two microwave signals, slightly separated in frequency, are injected into the plasma - to baseband, where a single frequency is used, in order to improve density fluctuation measurements. The second change, a variable frequency channel operating over the range from 122GHz to 140GHz (with corresponding density cutoffs of 1.84-2.43x10^20m-3) has been installed in collaboration with PPPL. Initial results from the upgraded system are presented, including the study of low density Internal Transport Barriers. Using O-mode waves, the reflectometry system is able to radially localize density fluctuations on the low field side along the tokamak midplane. It can, therefore, be used to probe the foot of low density ITBs. The corresponding reflectometry data will be compared to those of other fluctuation diagnostics, including Phase Contrast Imaging and magnetic pick-up coils.

TOPICAL REVIEW: Review of a chemical approach to YBa2Cu3O7-x-coated superconductors—metalorganic deposition using trifluoroacetates

NASA Astrophysics Data System (ADS)

Araki, Takeshi; Hirabayashi, Izumi

2003-11-01

Large-area, uniform, high critical current density (Jc) YBa2Cu3O7-x (YBCO) superconductor films are now routinely obtained by metalorganic deposition using trifluoroacetates (TFA-MOD). This method does not require any expensive vacuum apparatus at any time during the whole process. Thus, TFA-MOD is regarded as one of the most suitable candidates for fabricating a YBCO tape for many high-power applications. This method originated from an electron beam process using BaF2 developed by Mankiewich et al. Afterwards, Gupta et al reported using TFA-MOD to prepare a similar precursor film. These two ex situ processes used fluorides instead of BaCO3 to avoid the fatal deterioration in Jc, which is caused in the resulting films through metal carboxylic groups. Fluorides not only avoid such deterioration but also lead to perfectly c-axis-oriented epitaxial crystal growth. In conventional metalorganic deposition, nucleation in the precursor film causes random orientation in the resulting film. However, in TFA-MOD, nanocrystallites in the precursor film never cause such disorder. Furthermore, during the firing process of TFA-MOD, water and HF gas diffuse quickly between the film surface and growth front of the YBCO layer. This diffusion never limits the growth rate of YBCO. What distinguishes TFA-MOD from conventional metalorganic deposition? What happens during heat treatment? In this paper, we discuss all the TFA-MOD processes and the peculiar growth scheme of the YBCO layer in TFA-MOD using the model of a quasi-liquid network. In addition, we review the history of TFA-MOD and recent results and discuss the prospects of future applications.

Comparison of removal torques between laser-etched and modified sandblasted acid-etched Ti implant surfaces in rabbit tibias

PubMed Central

Al Awamleh, Abdel Ghani Ibrahim

2018-01-01

PURPOSE The purpose of this study was to analyze the effects of two different implant surface treatments on initial bone connection by comparing the Removal Torque Values (RTQs) at 7 and 10 days after chemically modified, sandblasted, large-grit and acid-etched (modSLA), and Laser-etched (LE) Ti implant placements. MATERIALS AND METHODS Twenty modSLA and 20 LE implants were installed on the left and right tibias of 20 adult rabbits. RTQs were measured after 7 and 10 days in 10 rabbits each. Scanning electron microscope (SEM) photographs of the two implants were observed by using Quanta FEG 650 from the FEI company (Hillsboro, OR, USA). Analyses of surface elements and components were conducted using energy dispersive spectroscopy (EDS, Horiba, Kyoto, Japan). RESULTS The mean RTQs were 12.29 ± 0.830 and 12.19 ± 0.713 Ncm after 7 days (P=.928) and 16.47 ± 1.324 and 16.17 ± 1.165 Ncm after 10 days (P=.867) for LE and modSLA, respectively, indicating no significant inter-group differences. Pore sizes in the LE were 40 µm and consisted of numerous small pores, whereas pore sizes in the modSLA were 5 µm. In the EDS analysis, Ti, O, and C were the only three elements found in the LE surfaces. Na, Ca, Cl, and K were also observed in modSLA, in addition to Ti, O, and C. CONCLUSION The implants showed no significant difference in biomechanical bond strength to bone in early-stage osseointegration. LE implant can be considered an excellent surface treatment method in addition to the modSLA implant and can be applied to the early loading of the prosthesis clinically. PMID:29503717

Changing impact of modifiable risk factors on the incidence of major outcomes of type 1 diabetes: the Pittsburgh Epidemiology of Diabetes Complications Study.

PubMed

Miller, Rachel G; Secrest, Aaron M; Ellis, Demetrius; Becker, Dorothy J; Orchard, Trevor J

2013-12-01

The incidence of type 1 diabetes complications appears to be decreasing, but relative contributions of risk factors are unclear. We thus estimated the effect of modifiable risk factors on the incidence of a composite end point, major outcomes of diabetes (MOD). The Pittsburgh Epidemiology of Diabetes Complications (EDC) Study was used to derive two cohorts based on diabetes diagnosis year (1960-1969 and 1970-1980). Baseline exam data in the current analysis for the 1960s group were collected in 1986-1988 and for the 1970s in 1996-1998. Each group was followed for 8 years for MOD incidence (diabetes-related death, myocardial infarction, revascularization procedure/blockage ≥50%, stroke, end-stage renal disease, blindness, and amputation). Assessed risk factors include the following: HbA1c, hypertension, microalbuminuria, BMI, hypercholesterolemia, and smoking. Accelerated failure time models were used to estimate the acceleration factor. MOD incidence decreased in the 1970s cohort (15.8% [95% CI 11.6-21.4]) compared with the 1960s (22.6% [17.0-29.1]) over the 8-year follow-up (P = 0.06). Hypertension and microalbuminuria were associated with significantly accelerated MOD incidence in both cohorts (P < 0.01 for both). High HbA1c (P = 0.0005), hypercholesterolemia (P = 0.01), and current smoking (P = 0.003) significantly accelerated the incidence of MOD in the 1960s but not 1970s cohort. BMI was not associated with MOD in either cohort. These results suggest that hypertension and microalbuminuria remain important predictors of complications that are not being adequately addressed.

VarMod: modelling the functional effects of non-synonymous variants.

PubMed

Pappalardo, Morena; Wass, Mark N

2014-07-01

Unravelling the genotype-phenotype relationship in humans remains a challenging task in genomics studies. Recent advances in sequencing technologies mean there are now thousands of sequenced human genomes, revealing millions of single nucleotide variants (SNVs). For non-synonymous SNVs present in proteins the difficulties of the problem lie in first identifying those nsSNVs that result in a functional change in the protein among the many non-functional variants and in turn linking this functional change to phenotype. Here we present VarMod (Variant Modeller) a method that utilises both protein sequence and structural features to predict nsSNVs that alter protein function. VarMod develops recent observations that functional nsSNVs are enriched at protein-protein interfaces and protein-ligand binding sites and uses these characteristics to make predictions. In benchmarking on a set of nearly 3000 nsSNVs VarMod performance is comparable to an existing state of the art method. The VarMod web server provides extensive resources to investigate the sequence and structural features associated with the predictions including visualisation of protein models and complexes via an interactive JSmol molecular viewer. VarMod is available for use at http://www.wasslab.org/varmod. © The Author(s) 2014. Published by Oxford University Press on behalf of Nucleic Acids Research.

A matter of hand: Causal links between hand dominance, structural organization of fronto-parietal attention networks, and variability in behavioural responses to transcranial magnetic stimulation.

PubMed

Cazzoli, Dario; Chechlacz, Magdalena

2017-01-01

Considerable evidence suggests that, on a group level, human visuospatial attention is asymmetrically organized, with a right-hemispheric dominance. The asymmetrical organization of the superior longitudinal fasciculus (SLF) has been shown to account for the right-hemispheric dominance in visual attention. However, such account is by no means universal, and large individual differences in asymmetrical performance on visuospatial tasks have been reported. Furthermore, the variability in the SLF lateralization has been shown to correlate with behavioural asymmetries. Continuous theta burst stimulation (cTBS) enables to temporarily interfere with cortical activity. cTBS applied over the posterior parietal cortex (PPC) has been previously used to systematically study attentional asymmetries. Interestingly, large individual differences in the effectiveness of stimulation have been reported. In accordance with earlier both animal and human studies, one possible cause underlying these striking individual differences might lie in the structural organization of frontoparietal pathways subserving visuospatial attention. Thus, the current study employed diffusion tractography to examine the relationship between the variability in the structural organization of the SLF and the individual differences in attentional shifts induced by a modified cTBS (cTBS mod ; triplets of pulses at 30 Hz, repeated at 6 Hz) applied over the IPS, as measured by a line bisection task. Consistent with previous studies, on a group level, cTBS mod applied over the right intraparietal sulcus (IPS) triggered a rightward bisection bias shift, and there were no significant effects of cTBS mod applied over the left IPS. However, further analyses demonstrated that both handedness and structural variability (as assessed based on hindrance modulated orientational anisotropy) within the middle and the ventral branches of the SLF predicted individual differences in the cTBS mod -induced attentional shifts. Our study thus suggests that the effects of cTBS mod over the IPS may depend on intra-hemispheric interactions between cortical loci controlling visual attention. To conclude, our findings provide converging evidence for the notion put forward previously that inter-individual variability in the structural organization of intra-hemispheric frontoparietal connections has important implications for the functional models of human visual attention. Moreover, we hypothesize that this may also be relevant for the understanding of attentional disorders and their rehabilitation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Half-marathon and full-marathon runners' hydration practices and perceptions.

PubMed

O'Neal, Eric K; Wingo, Jonathan E; Richardson, Mark T; Leeper, James D; Neggers, Yasmine H; Bishop, Phil A

2011-01-01

The behaviors and beliefs of recreational runners with regard to hydration maintenance are not well elucidated. To examine which beverages runners choose to drink and why, negative performance and health experiences related to dehydration, and methods used to assess hydration status. Cross-sectional study. Marathon registration site. Men (n = 146) and women (n = 130) (age = 38.3 ± 11.3 years) registered for the 2010 Little Rock Half-Marathon or Full Marathon. A 23-item questionnaire was administered to runners when they picked up their race timing chips. Runners were separated into tertiles (Low, Mod, High) based on z scores derived from training volume, expected performance, and running experience. We used a 100-mm visual analog scale with anchors of 0 (never) and 100 (always). Total sample responses and comparisons between tertile groups for questionnaire items are presented. The High group (58±31) reported greater consumption of sport beverages in exercise environments than the Low (42 ± 35 mm) and Mod (39 ± 32 mm) groups (P < .05) and perceived sport beverages to be superior to water in meeting hydration needs (P < .05) and improving performance during runs greater than 1 hour (P < .05). Seventy percent of runners experienced 1 or more incidents in which they believed dehydration resulted in a major performance decrement, and 45% perceived dehydration to have resulted in adverse health effects. Twenty percent of runners reported monitoring their hydration status. Urine color was the method most often reported (7%), whereas only 2% reported measuring changes in body weight. Greater attention should be paid to informing runners of valid techniques to monitor hydration status and developing an appropriate individualized hydration strategy.

Half-Marathon and Full-Marathon Runners' Hydration Practices and Perceptions

PubMed Central

O'Neal, Eric K.; Wingo, Jonathan E.; Richardson, Mark T.; Leeper, James D.; Neggers, Yasmine H.; Bishop, Phil A.

2011-01-01

Context: The behaviors and beliefs of recreational runners with regard to hydration maintenance are not well elucidated. Objective: To examine which beverages runners choose to drink and why, negative performance and health experiences related to dehydration, and methods used to assess hydration status. Design: Cross-sectional study. Setting: Marathon registration site. Patients or Other Participants: Men (n = 146) and women (n = 130) (age = 38.3 ± 11.3 years) registered for the 2010 Little Rock Half-Marathon or Full Marathon. Intervention(s): A 23-item questionnaire was administered to runners when they picked up their race timing chips. Main Outcome Measure(s): Runners were separated into tertiles (Low, Mod, High) based on z scores derived from training volume, expected performance, and running experience. We used a 100-mm visual analog scale with anchors of 0 (never) and 100 (always). Total sample responses and comparisons between tertile groups for questionnaire items are presented. Results: The High group (58±31) reported greater consumption of sport beverages in exercise environments than the Low (42 ± 35 mm) and Mod (39 ± 32 mm) groups (P < .05) and perceived sport beverages to be superior to water in meeting hydration needs (P < .05) and improving performance during runs greater than 1 hour (P < .05). Seventy percent of runners experienced 1 or more incidents in which they believed dehydration resulted in a major performance decrement, and 45% perceived dehydration to have resulted in adverse health effects. Twenty percent of runners reported monitoring their hydration status. Urine color was the method most often reported (7%), whereas only 2% reported measuring changes in body weight. Conclusions: Greater attention should be paid to informing runners of valid techniques to monitor hydration status and developing an appropriate individualized hydration strategy. PMID:22488182

On the potential of a new IVUS elasticity modulus imaging approach for detecting vulnerable atherosclerotic coronary plaques: In vitro vessel phantom study

PubMed Central

Le Floc’h, Simon; Cloutier, Guy; Finet, Gérard; Tracqui, Philippe; Pettigrew, Roderic I.; Ohayon, Jacques

2016-01-01

Peak cap stress amplitude is recognized as a good indicator of vulnerable plaque (VP) rupture. However, such stress evaluation strongly relies on a precise, but still lacking, knowledge of the mechanical properties exhibited by the plaque components. As a first response to this limitation, our group recently developed, in a previous theoretical study, an original approach, called iMOD, which reconstructs elasticity maps (or modulograms) of atheroma plaques from the estimation of strain fields. In the present in vitro experimental study, conducted on PVA-C arterial phantoms, we investigate the benefit of coupling the iMOD procedure with the acquisition of intravascular ultrasound (IVUS) measurements for detection of VP. Our results show that the combined iMOD-IVUS strategy : 1) successfully detected and quantified soft inclusion contours with high positive predictive values and sensitivities of 89.7 ± 3.9% and 81.5 ± 8.8 %, respectively, 2) estimated reasonably cap thicknesses larger than ~300 µm, but underestimated thinner caps, and 3) quantified satisfactorily Young's modulus of hard medium (mean value of 109.7 ± 23.7 kPa instead of 145.4 ± 31.8 kPa), but overestimated the stiffness of soft inclusions (mean Young`s moduli of 31.4 ± 9.7 kPa instead of 17.6 ± 3.4 kPa). All together, these results demonstrate a promising benefit of the new iMOD-IVUS clinical imaging method for in vivo VP detection. PMID:20826899

From the Last Interglacial to the Anthropocene: Modelling a Complete Glacial Cycle (PalMod)

NASA Astrophysics Data System (ADS)

Brücher, Tim; Latif, Mojib

2017-04-01

We will give a short overview and update on the current status of the national climate modelling initiative PalMod (Paleo Modelling, www.palmod.de). PalMod focuses on the understanding of the climate system dynamics and its variability during the last glacial cycle. The initiative is funded by the German Federal Ministry of Education and Research (BMBF) and its specific topics are: (i) to identify and quantify the relative contributions of the fundamental processes which determined the Earth's climate trajectory and variability during the last glacial cycle, (ii) to simulate with comprehensive Earth System Models (ESMs) the climate from the peak of the last interglacial - the Eemian warm period - up to the present, including the changes in the spectrum of variability, and (iii) to assess possible future climate trajectories beyond this century during the next millennia with sophisticated ESMs tested in such a way. The research is intended to be conducted over a period of 10 years, but with shorter funding cycles. PalMod kicked off in February 2016. The first phase focuses on the last deglaciation (app. the last 23.000 years). From the ESM perspective PalMod pushes forward model development by coupling ESM with dynamical ice sheet models. Computer scientists work on speeding up climate models using different concepts (like parallelisation in time) and one working group is dedicated to perform a comprehensive data synthesis to validate model performance. The envisioned approach is innovative in three respects. First, the consortium aims at simulating a full glacial cycle in transient mode and with comprehensive ESMs which allow full interactions between the physical and biogeochemical components of the Earth system, including ice sheets. Second, we shall address climate variability during the last glacial cycle on a large range of time scales, from interannual to multi-millennial, and attempt to quantify the relative contributions of external forcing and processes internal to the Earth system to climate variability at different time scales. Third, in order to achieve a higher level of understanding of natural climate variability at time scales of millennia, its governing processes and implications for the future climate, we bring together three different research communities: the Earth system modeling community, the proxy data community and the computational science community. The consortium consists of 18 partners including all major modelling centers within Germany. The funding comprises approximately 65 PostDoc positions and more than 120 scientists are involved. PalMod is coordinated at the Helmholtz Centre for Ocean Research Kiel (GEOMAR).

Rotation and transport in Alcator C-Mod ITB plasmas

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Rice, J. E.; Podpaly, Y.; Bespamyatnov, I. O.; Rowan, W. L.; Hughes, J. W.; Reinke, M.

2010-06-01

Internal transport barriers (ITBs) are seen under a number of conditions in Alcator C-Mod plasmas. Most typically, radio frequency power in the ion cyclotron range of frequencies (ICRFs) is injected with the second harmonic of the resonant frequency for minority hydrogen ions positioned off-axis at r/a > 0.5 to initiate the ITBs. They can also arise spontaneously in ohmic H-mode plasmas. These ITBs typically persist tens of energy confinement times until the plasma terminates in radiative collapse or a disruption occurs. All C-Mod core barriers exhibit strongly peaked density and pressure profiles, static or peaking temperature profiles, peaking impurity density profiles and thermal transport coefficients that approach neoclassical values in the core. The strongly co-current intrinsic central plasma rotation that is observed following the H-mode transition has a profile that is peaked in the centre of the plasma and decreases towards the edge if the ICRF power deposition is in the plasma centre. When the ICRF resonance is placed off-axis, the rotation develops a well in the core region. The central rotation continues to decrease as long as the central density peaks when an ITB develops. This rotation profile is flat in the centre (0 < r/a < 0.4) but rises steeply in the region where the foot in the ITB density profile is observed (0.5 < r/a < 0.7). A correspondingly strong E × B shear is seen at the location of the ITB foot that is sufficiently large to stabilize ion temperature gradient instabilities that dominate transport in C-Mod high density plasmas.

Digital Plasma Control System for Alcator C-Mod

NASA Astrophysics Data System (ADS)

Ferrara, M.; Wolfe, S.; Stillerman, J.; Fredian, T.; Hutchinson, I.

2004-11-01

A digital plasma control system (DPCS) has been designed to replace the present C-Mod system, which is based on hybrid analog-digital computer. The initial implementation of DPCS comprises two 64 channel, 16 bit, low-latency cPCI digitizers, each with 16 analog outputs, controlled by a rack-mounted single-processor Linux server, which also serves as the compute engine. A prototype system employing three older 32 channel digitizers was tested during the 2003-04 campaign. The hybrid's linear PID feedback system was emulated by IDL code executing a synchronous loop, using the same target waveforms and control parameters. Reliable real-time operation was accomplished under a standard Linux OS (RH9) by locking memory and disabling interrupts during the plasma pulse. The DPCS-computed outputs agreed to within a few percent with those produced by the hybrid system, except for discrepancies due to offsets and non-ideal behavior of the hybrid circuitry. The system operated reliably, with no sample loss, at more than twice the 10kHz design specification, providing extra time for implementing more advanced control algorithms. The code is fault-tolerant and produces consistent output waveforms even with 10% sample loss.

The flush-mounted rail Langmuir probe array designed for the Alcator C-Mod vertical target plate divertor

NASA Astrophysics Data System (ADS)

Kuang, A. Q.; Brunner, D.; LaBombard, B.; Leccacorvi, R.; Vieira, R.

2018-04-01

An array of flush-mounted and toroidally elongated Langmuir probes (henceforth called rail probes) have been specifically designed for the Alcator C-Mod's vertical target plate divertor and operated over multiple campaigns. The "flush" geometry enables the tungsten electrodes to survive high heat flux conditions in which traditional "proud" tungsten electrodes suffer damage from melting. The toroidally elongated rail-like geometry reduces the influence of sheath expansion, which is an important effect to consider in the design and interpretation of flush-mounted Langmuir probes. The new rail probes successfully operated during C-Mod's FY2015 and FY2016 experimental campaigns with no evidence of damage, despite being regularly subjected to heat flux densities parallel to the magnetic field exceeding ˜1 GW m-2 for short periods of time. A comparison between rail and proud probe data indicates that sheath expansion effects were successfully mitigated by the rail design, extending the use of these Langmuir probes to incident magnetic field line angles as low as 0.5°.

Extension of the lod score: the mod score.

PubMed

Clerget-Darpoux, F

2001-01-01

In 1955 Morton proposed the lod score method both for testing linkage between loci and for estimating the recombination fraction between them. If a disease is controlled by a gene at one of these loci, the lod score computation requires the prior specification of an underlying model that assigns the probabilities of genotypes from the observed phenotypes. To address the case of linkage studies for diseases with unknown mode of inheritance, we suggested (Clerget-Darpoux et al., 1986) extending the lod score function to a so-called mod score function. In this function, the variables are both the recombination fraction and the disease model parameters. Maximizing the mod score function over all these parameters amounts to maximizing the probability of marker data conditional on the disease status. Under the absence of linkage, the mod score conforms to a chi-square distribution, with extra degrees of freedom in comparison to the lod score function (MacLean et al., 1993). The mod score is asymptotically maximum for the true disease model (Clerget-Darpoux and Bonaïti-Pellié, 1992; Hodge and Elston, 1994). Consequently, the power to detect linkage through mod score will be highest when the space of models where the maximization is performed includes the true model. On the other hand, one must avoid overparametrization of the model space. For example, when the approach is applied to affected sibpairs, only two constrained disease model parameters should be used (Knapp et al., 1994) for the mod score maximization. It is also important to emphasize the existence of a strong correlation between the disease gene location and the disease model. Consequently, there is poor resolution of the location of the susceptibility locus when the disease model at this locus is unknown. Of course, this is true regardless of the statistics used. The mod score may also be applied in a candidate gene strategy to model the potential effect of this gene in the disease. Since, however, it ignores the information provided both by disease segregation and by linkage disequilibrium between the marker alleles and the functional disease alleles, its power of discrimination between genetic models is weak. The MASC method (Clerget-Darpoux et al., 1988) has been designed to address more efficiently the objectives of a candidate gene approach.

The Modified Frontal Behavioral Inventory (FBI-mod) for Patients with Frontotemporal Lobar Degeneration, Alzheimer's Disease, and Mild Cognitive Impairment.

PubMed

Suhonen, Noora-Maria; Hallikainen, Ilona; Hänninen, Tuomo; Jokelainen, Jari; Krüger, Johanna; Hall, Anette; Pikkarainen, Maria; Soininen, Hilkka; Remes, Anne M

2017-01-01

While behavioral symptoms are both early and prevalent features of behavioral variant frontotemporal dementia (bvFTD), they can be present in other types of dementia as well, including Alzheimer's disease (AD) and even mild cognitive impairment (MCI). The Frontal Behavioral Inventory (FBI) was specifically developed to capture the behavioral and personality changes in bvFTD; it has also been modified into a self-administered caregiver questionnaire (FBI-mod). We examined the utility of the FBI-mod in differentiating bvFTD (n = 26), primary progressive aphasia (PPA) (n = 7), AD (n = 53), and MCI (n = 50) patients, and investigated how the FBI-mod may be associated with neuropsychological measures. The bvFTD patients scored significantly higher as compared to all other patient groups on the FBI-mod Total (p < 0.005), Negative (p < 0.005), and Positive (p < 0.01) scores. The cut-off point for the FBI-mod Total score that best discriminated the bvFTD and AD patients in our sample was 16, thus substantially lower than reported for the original FBI. For the bvFTD group, only mild correlations emerged between the FBI-mod and the cognitive measures. However, significant correlations between the FBI-mod and depressive symptoms as measured by the BDI-II were found for bvFTD. This suggests that while behavioral symptoms appear independent from cognitive deficits in bvFTD, they may nevertheless be interrelated with depressive symptoms. We conclude that the FBI-mod is an easily administered behavioral scale that can aid in differential diagnosis of bvFTD and should be used in clinical practice. The FBI-mod may further be considered as an outcome measure in clinical trials.

Effects of dynamically variable saturation and matrix-conduit coupling of flow in karst aquifers

USGS Publications Warehouse

Reimann, T.; Geyer, T.; Shoemaker, W.B.; Liedl, R.; Sauter, M.

2011-01-01

Well-developed karst aquifers consist of highly conductive conduits and a relatively low permeability fractured and/or porous rock matrix and therefore behave as a dual-hydraulic system. Groundwater flow within highly permeable strata is rapid and transient and depends on local flow conditions, i.e., pressurized or nonpressurized flow. The characterization of karst aquifers is a necessary and challenging task because information about hydraulic and spatial conduit properties is poorly defined or unknown. To investigate karst aquifers, hydraulic stresses such as large recharge events can be simulated with hybrid (coupled discrete continuum) models. Since existing hybrid models are simplifications of the system dynamics, a new karst model (ModBraC) is presented that accounts for unsteady and nonuniform discrete flow in variably saturated conduits employing the Saint-Venant equations. Model performance tests indicate that ModBraC is able to simulate (1) unsteady and nonuniform flow in variably filled conduits, (2) draining and refilling of conduits with stable transition between free-surface and pressurized flow and correct storage representation, (3) water exchange between matrix and variably filled conduits, and (4) discharge routing through branched and intermeshed conduit networks. Subsequently, ModBraC is applied to an idealized catchment to investigate the significance of free-surface flow representation. A parameter study is conducted with two different initial conditions: (1) pressurized flow and (2) free-surface flow. If free-surface flow prevails, the systems is characterized by (1) a time lag for signal transmission, (2) a typical spring discharge pattern representing the transition from pressurized to free-surface flow, and (3) a reduced conduit-matrix interaction during free-surface flow. Copyright 2011 by the American Geophysical Union.

Multi-scale gyrokinetic simulation of Alcator C-Mod tokamak discharges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, N. T., E-mail: nthoward@psfc.mit.edu; White, A. E.; Greenwald, M.

2014-03-15

Alcator C-Mod tokamak discharges have been studied with nonlinear gyrokinetic simulation simultaneously spanning both ion and electron spatiotemporal scales. These multi-scale simulations utilized the gyrokinetic model implemented by GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] and the approximation of reduced electron mass (μ = (m{sub D}/m{sub e}){sup .5} = 20.0) to qualitatively study a pair of Alcator C-Mod discharges: a low-power discharge, previously demonstrated (using realistic mass, ion-scale simulation) to display an under-prediction of the electron heat flux and a high-power discharge displaying agreement with both ion and electron heat flux channels [N. T. Howard et al.,more » Nucl. Fusion 53, 123011 (2013)]. These multi-scale simulations demonstrate the importance of electron-scale turbulence in the core of conventional tokamak discharges and suggest it is a viable candidate for explaining the observed under-prediction of electron heat flux. In this paper, we investigate the coupling of turbulence at the ion (k{sub θ}ρ{sub s}∼O(1.0)) and electron (k{sub θ}ρ{sub e}∼O(1.0)) scales for experimental plasma conditions both exhibiting strong (high-power) and marginally stable (low-power) low-k (k{sub θ}ρ{sub s} < 1.0) turbulence. It is found that reduced mass simulation of the plasma exhibiting marginally stable low-k turbulence fails to provide even qualitative insight into the turbulence present in the realistic plasma conditions. In contrast, multi-scale simulation of the plasma condition exhibiting strong turbulence provides valuable insight into the coupling of the ion and electron scales.« less

Edge Turbulence Imaging in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Zweben, Stewart J.

2001-10-01

This talk will describe measurements and modeling of the 2-D structure of edge turbulence in Alcator C-Mod. The radial vs. poloidal structure was measured using Gas Puff Imaging (GPI) (R. Maqueda et al, RSI 72, 931 (2001), J. Terry et al, J. Nucl. Materials 290-293, 757 (2001)), in which the visible light emitted by an edge neutral gas puff (generally D or He) is viewed along the local magnetic field by a fast-gated video camera. Strong fluctuations are observed in the gas cloud light emission when the camera is gated at ~2 microsec exposure time per frame. The structure of these fluctuations is highly turbulent with a typical radial and poloidal scale of ≈1 cm, and often with local maxima in the scrape-off layer (i.e. ``blobs"). Video clips and analyses of these images will be presented along with their variation in different plasma regimes. The local time dependence of edge turbulence is measured using high-speed photodiodes viewing the gas puff emission, a scanning Langmuir probe, and also with a Princeton Scientific Instruments ultra-fast framing camera, which can make 2-D images the gas puff at up to 200,000 frames/sec. Probe measurements show that the strong turbulence region moves to the separatrix as the density limit is approached, which may be connected to the density limit (B. LaBombard et al., Phys. Plasmas 8 2107 (2001)). Comparisons of this C-Mod turbulence data will be made with results of simulations from the Drift-Ballooning Mode (DBM) (B.N. Rogers et al, Phys. Rev. Lett. 20 4396 (1998))and Non-local Edge Turbulence (NLET) codes.

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 2

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3MW MOD-5A wind turbine generator is documented. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 3, book 2 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. The subsystem for power generation, control, and instrumentation subsystems is described in detail. The manufacturing and construction plans, and the preparation of a potential site on Oahu, Hawaii, are documented. The quality assurance and safety plan, and analyses of failure modes and effects, and reliability, availability and maintainability are presented.

WEST-3 wind turbine simulator development. Volume 2: Verification

NASA Technical Reports Server (NTRS)

Sridhar, S.

1985-01-01

The details of a study to validate WEST-3, a new time wind turbine simulator developed by Paragib Pacific Inc., are presented in this report. For the validation, the MOD-0 wind turbine was simulated on WEST-3. The simulation results were compared with those obtained from previous MOD-0 simulations, and with test data measured during MOD-0 operations. The study was successful in achieving the major objective of proving that WEST-3 yields results which can be used to support a wind turbine development process. The blade bending moments, peak and cyclic, from the WEST-3 simulation correlated reasonably well with the available MOD-0 data. The simulation was also able to predict the resonance phenomena observed during MOD-0 operations. Also presented in the report is a description and solution of a serious numerical instability problem encountered during the study. The problem was caused by the coupling of the rotor and the power train models. The results of the study indicate that some parts of the existing WEST-3 simulation model may have to be refined for future work; specifically, the aerodynamics and procedure used to couple the rotor model with the tower and the power train models.

47 CFR 1.1152 - Schedule of annual regulatory fees and filing locations for wireless radio services.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) (47 CFR, Part 90) (a) New, Renew/Mod (FCC 601 & 159) $40.00 FCC, P.O. Box 979097, St. Louis, MO 63197-9000. (b) New, Renew/Mod (Electronic Filing) (FCC 601 & 159) 40.00 FCC, P.O. Box 979097, St. Louis, MO 63197-9000. (c) Renewal Only (FCC 601 & 159) 40.00 FCC, P.O. Box 979097, St. Louis, MO 63197-9000. (d...

Control of substrate oxidation in MOD cerawwwmic coating on low-activation ferritic steel with reduced-pressure atmosphere

NASA Astrophysics Data System (ADS)

Tanaka, Teruya; Muroga, Takeo

2014-12-01

An Er2O3 ceramic coating fabricated using the metal-organic decomposition (MOD) method on a Cr2O3-covered low-activation ferritic steel JLF-1 substrate was examined to improve hydrogen permeation barrier performance of the coating. The Cr2O3 layer was obtained before coating by heat treating the substrate at 700 °C under reduced pressures of <5 × 10-3 Pa and 5 Pa. The Cr2O3 layer was significantly stable even with heat treatment at 700 °C in air. This layer prevented further production of Fe2O3, which has been considered to degrade coating performance. An MOD Er2O3 coating with a smooth surface was successfully obtained on a Cr2O3-covered JLF-1 substrate by dip coating followed by drying and baking. Preprocessing to obtain a Cr2O3 layer would provide flexibility in the coating process for blanket components and ducts. Moreover, the Cr2O3 layer suppressed hydrogen permeation through the JLF-1 substrate. While further optimization of the coating fabrication process is required, it would be possible to suppress hydrogen permeation significantly by multilayers of Cr2O3 and MOD oxide ceramic.

RETRAN analysis of multiple steam generator blow down caused by an auxiliary feedwater steam-line break

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feltus, M.A.

1987-01-01

Analysis results for multiple steam generator blow down caused by an auxiliary feedwater steam-line break performed with the RETRAN-02 MOD 003 computer code are presented to demonstrate the capabilities of the RETRAN code to predict system transient response for verifying changes in operational procedures and supporting plant equipment modifications. A typical four-loop Westinghouse pressurized water reactor was modeled using best-estimate versus worst case licensing assumptions. This paper presents analyses performed to evaluate the necessity of implementing an auxiliary feedwater steam-line isolation modification. RETRAN transient analysis can be used to determine core cooling capability response, departure from nucleate boiling ratio (DNBR)more » status, and reactor trip signal actuation times.« less

Active MHD Spectroscopy of Alfvén Eigenmodes on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Sears, J.; Snipes, J.; Burke, W.; Parker, R.; Fasoli, A.

2004-11-01

Alfvén eigenmode resonances are excited in a variety of plasma conditions in C-Mod with two moderate-n antennas positioned above and below the outboard midplane. Power amplifiers (≈ 3 kW) sweep the driving frequency over the audio range (< 30 kHz) or over a selected ± 50 kHz range from 100 kHz to 1 MHz. Logic circuitry that calculates the center frequency of the Toroidal Alfven Eigenmode gap, f_TAE=v_A/4π qR, in real-time from BT and e measurements is being developed to enable the antennas to track f_TAE. Simultaneous in-vessel phase calibration of the pick-up coils will be used to better identify toroidal mode numbers. Shot-to-shot elongation scans do not show the dependence of damping on edge shear that was seen in results at JET. Inner wall limited plasmas with moderate outer gaps show higher damping rates than diverted plasmas with low outer gaps. Low frequency experiments below 20kHz will also be presented.

Analysis of Rotation and Transport Data in C-Mod ITB Plasmas

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Rice, J. E.; Reinke, M. L.; Podpaly, Y.; Bespamyatnov, I. O.; Rowan, W. L.

2009-11-01

Internal transport barriers (ITBs) spontaneously form near the half radius of Alcator C-Mod plasmas when the EDA H-mode is sustained for several energy confinement times in either off-axis ICRF heated discharges or in purely ohmic heated plasmas. These plasmas exhibit strongly peaked density and pressure profiles, static or peaking temperature profiles, peaking impurity density profiles, and thermal transport coefficients that approach neoclassical values in the core. It has long been observed that the intrinsic central plasma rotation that is strongly co-current following the H-mode transition slows and often reverses as the density peaks as the ITB forms. Recent spatial measurements demonstrate that the rotation profile develops a well in the core region that decreases continuously as central density rises while the value outside of the core remains strongly co-current. This results in the formation of a steep potential gradient/strong electric field at the location of the foot of the ITB density profile. The resulting E X B shearing rate is also quite significant at the foot. These analyses and the implications for plasma transport and stability will be presented.

The role of turbulent suppression in the triggering ITBs on C-Mod

NASA Astrophysics Data System (ADS)

Zhurovich, K.; Fiore, C. L.; Ernst, D. R.; Bonoli, P. T.; Greenwald, M. J.; Hubbard, A. E.; Hughes, J. W.; Marmar, E. S.; Mikkelsen, D. R.; Phillips, P.; Rice, J. E.

2007-11-01

Internal transport barriers can be routinely produced in C-Mod steady EDA H-mode plasmas by applying ICRF at |r/a|>= 0.5. Access to the off-axis ICRF heated ITBs may be understood within the paradigm of marginal stability. Analysis of the Te profiles shows a decrease of R/LTe in the ITB region as the RF resonance is moved off axis. Ti profiles broaden as the ICRF power deposition changes from on-axis to off-axis. TRANSP calculations of the Ti profiles support this trend. Linear GS2 calculations do not reveal any difference in ETG growth rate profiles for ITB vs. non-ITB discharges. However, they do show that the region of stability to ITG modes widens as the ICRF resonance is moved outward. Non-linear simulations show that the outward turbulent particle flux exceeds the Ware pinch by factor of 2 in the outer plasma region. Reducing the temperature gradient significantly decreases the diffusive flux and allows the Ware pinch to peak the density profile. Details of these experiments and simulations will be presented.

Scrape-off layer reflectometer for Alcator C-Mod.

PubMed

Lau, Cornwall; Hanson, Greg; Wilgen, John; Lin, Yijun; Wukitch, Steve

2010-10-01

A swept-frequency X-mode reflectometer is being built for Alcator C-Mod to measure the scrape-off layer density profiles at the top, middle, and bottom locations in front of both the new lower hybrid launcher and the new ion cyclotron range of frequencies antenna. The system is planned to operate between 100 and 146 GHz at sweep rates from 10 μs to 1 ms, and will cover a density range of approximately 10(16)-10(20) m(-3) at B(0)=5-5.4 T. To minimize the effects of density fluctuations, both differential phase and full phase reflectometry will be employed. Design, test data, and calibration results of this electronics system will be discussed. To reduce attenuation losses, tallguide (TE(01)) will be used for most of the transmission line system. Simulations of high mode conversion in tallguide components, such as e-plane hyperbolic secant radius of curvature bends, tapers, and horn antennas will be shown. Experimental measurements of the total attenuation losses of these components in the lower hybrid waveguide run will also be presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pablant, N. A.; Delgado-Aparicio, L.; Bitter, M.

A new energy resolving x-ray pinhole camera has been recently installed on Alcator C-Mod. This diagnostic is capable of 1D or 2D imaging with a spatial resolution of Almost-Equal-To 1 cm, an energy resolution of Almost-Equal-To 1 keV in the range of 3.5-15 keV and a maximum time resolution of 5 ms. A novel use of a Pilatus 2 hybrid-pixel x-ray detector [P. Kraft et al., J. Synchrotron Rad. 16, 368 (2009)] is employed in which the lower energy threshold of individual pixels is adjusted, allowing regions of a single detector to be sensitive to different x-ray energy ranges. Developmentmore » of this new detector calibration technique was done as a collaboration between PPPL and Dectris Ltd. The calibration procedure is described, and the energy resolution of the detector is characterized. Initial data from this installation on Alcator C-Mod is presented. This diagnostic provides line-integrated measurements of impurity emission which can be used to determine impurity concentrations as well as the electron energy distribution.« less

Protease-resistant modified human β-hexosaminidase B ameliorates symptoms in GM2 gangliosidosis model

PubMed Central

Mizutani, Yasumichi; Sugiyama, Eiji; Tasaki, Chikako; Tsuji, Daisuke; Maita, Nobuo; Hirokawa, Takatsugu; Asanuma, Daisuke; Kamiya, Mako; Sato, Kohei; Setou, Mitsutoshi; Urano, Yasuteru; Togawa, Tadayasu; Otaka, Akira; Sakuraba, Hitoshi

2016-01-01

GM2 gangliosidoses, including Tay-Sachs and Sandhoff diseases, are neurodegenerative lysosomal storage diseases that are caused by deficiency of β-hexosaminidase A, which comprises an αβ heterodimer. There are no effective treatments for these diseases; however, various strategies aimed at restoring β-hexosaminidase A have been explored. Here, we produced a modified human hexosaminidase subunit β (HexB), which we have termed mod2B, composed of homodimeric β subunits that contain amino acid sequences from the α subunit that confer GM2 ganglioside–degrading activity and protease resistance. We also developed fluorescent probes that allow visualization of endocytosis of mod2B via mannose 6-phosphate receptors and delivery of mod2B to lysosomes in GM2 gangliosidosis models. In addition, we applied imaging mass spectrometry to monitor efficacy of this approach in Sandhoff disease model mice. Following i.c.v. administration, mod2B was widely distributed and reduced accumulation of GM2, asialo-GM2, and bis(monoacylglycero)phosphate in brain regions including the hypothalamus, hippocampus, and cerebellum. Moreover, mod2B administration markedly improved motor dysfunction and a prolonged lifespan in Sandhoff disease mice. Together, the results of our study indicate that mod2B has potential for intracerebrospinal fluid enzyme replacement therapy and should be further explored as a gene therapy for GM2 gangliosidoses. PMID:27018595

Protease-resistant modified human β-hexosaminidase B ameliorates symptoms in GM2 gangliosidosis model.

PubMed

Kitakaze, Keisuke; Mizutani, Yasumichi; Sugiyama, Eiji; Tasaki, Chikako; Tsuji, Daisuke; Maita, Nobuo; Hirokawa, Takatsugu; Asanuma, Daisuke; Kamiya, Mako; Sato, Kohei; Setou, Mitsutoshi; Urano, Yasuteru; Togawa, Tadayasu; Otaka, Akira; Sakuraba, Hitoshi; Itoh, Kohji

2016-05-02

GM2 gangliosidoses, including Tay-Sachs and Sandhoff diseases, are neurodegenerative lysosomal storage diseases that are caused by deficiency of β-hexosaminidase A, which comprises an αβ heterodimer. There are no effective treatments for these diseases; however, various strategies aimed at restoring β-hexosaminidase A have been explored. Here, we produced a modified human hexosaminidase subunit β (HexB), which we have termed mod2B, composed of homodimeric β subunits that contain amino acid sequences from the α subunit that confer GM2 ganglioside-degrading activity and protease resistance. We also developed fluorescent probes that allow visualization of endocytosis of mod2B via mannose 6-phosphate receptors and delivery of mod2B to lysosomes in GM2 gangliosidosis models. In addition, we applied imaging mass spectrometry to monitor efficacy of this approach in Sandhoff disease model mice. Following i.c.v. administration, mod2B was widely distributed and reduced accumulation of GM2, asialo-GM2, and bis(monoacylglycero)phosphate in brain regions including the hypothalamus, hippocampus, and cerebellum. Moreover, mod2B administration markedly improved motor dysfunction and a prolonged lifespan in Sandhoff disease mice. Together, the results of our study indicate that mod2B has potential for intracerebrospinal fluid enzyme replacement therapy and should be further explored as a gene therapy for GM2 gangliosidoses.

MODIS Collection 6 Clear Sky Restoral (CSR): Filtering Cloud Mast 'Not Clear' Pixels

NASA Technical Reports Server (NTRS)

Meyer, Kerry G.; Platnick, Steven Edward; Wind, Galina; Riedi, Jerome

2014-01-01

Correctly identifying cloudy pixels appropriate for the MOD06 cloud optical and microphysical property retrievals is accomplished in large part using results from the MOD35 1km cloud mask tests (note there are also two 250m subpixel cloud mask tests that can convert the 1km cloudy designations to clear sky). However, because MOD35 is by design clear sky conservative (i.e., it identifies "not clear" pixels), certain situations exist in which pixels identified by MOD35 as "cloudy" are nevertheless likely to be poor retrieval candidates. For instance, near the edge of clouds or within broken cloud fields, a given 1km MODIS field of view (FOV) may in fact only be partially cloudy. This can be problematic for the MOD06 retrievals because in these cases the assumptions of a completely overcast homogenous cloudy FOV and 1-dimensional plane-parallel radiative transfer no longer hold, and subsequent retrievals will be of low confidence. Furthermore, some pixels may be identified by MOD35 as "cloudy" for reasons other than the presence of clouds, such as scenes with thick smoke or lofted dust, and should therefore not be retrieved as clouds. With such situations in mind, a Clear Sky Restoral (CSR) algorithm was introduced in C5 that attempts to identify pixels expected to be poor retrieval candidates. Table 1 provides SDS locations for CSR and partly cloudy (PCL) pixels.

A Study of Electron Modes in Off-axis Heated Alcator C-Mod Plasmas

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Ernst, D. R.; Mikkelsen, D.; Ennever, P. C.; Howard, N. T.; Gao, C.; Reinke, M. L.; Rice, J. E.; Hughes, J. W.; Walk, J. R.

2013-10-01

Understanding the underlying physics and stability of the peaked density internal transport barriers (ITB) that have been observed during off-axis ICRF heating of Alcator C-Mod plasmas is the goal of recent gyro-kinetic simulations. Two scenarios are examined: an ITB plasma formed with maximal (4.5 MW) off-axis heating power; also the use of off-axis heating in an I-mode plasma as a target in the hopes of establishing an ITB. In the former, it is expected that evidence of trapped electron mode instabilities could be found if a sufficiently high electron temperature is achieved in the core. Linear simulations show unstable modes are present across the plasma core from r/a = 0.2 and greater. In the latter case, despite establishing similar conditions to those in which ITBS were formed, none developed in the I-mode plasmas. Linear gyrokinetic analyses show no unstable ion modes at r/a < 0.55 in these I-mode plasmas, with both ITG and ETG modes present beyond r/a = 0.65. The details of the experimental results will be presented. Linear and non-linear simulations of both of these cases will attempt to explore the underlying role of electron and ion gradient driven instabilities to explain the observations. This work was supported by US-DoE DE-FC02-99ER54512 and DE-AC02-09CH11466.

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

NASA Technical Reports Server (NTRS)

Spera, D. A.

1976-01-01

Preliminary estimates are presented of vibratory loads and stresses in hingeless and teetering rotors for the proposed NSF-NASA Mod-0 wind power system. Preliminary blade design utilizes a tapered tubular aluminum spar which supports nonstructural aluminum ribs and skin and is joined to the rotor hub by a steel shank tube. Stresses in the shank of the blade are calculated for static, rated, and overload operating conditions. Blade vibrations were limited to the fundamental flapping modes, which were elastic cantilever bending for hingeless rotor blades and rigid-body rotation for teetering rotor blades. The MOSTAB-C computer code was used to calculate aerodynamic and mechanical loads. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. The hingeless rotor analyzed does not appear to be structurally stable during overloads.

Use of reconstructed 3D equilibria to determine onset conditions of helical cores in tokamaks for extrapolation to ITER

NASA Astrophysics Data System (ADS)

Wingen, A.; Wilcox, R. S.; Seal, S. K.; Unterberg, E. A.; Cianciosa, M. R.; Delgado-Aparicio, L. F.; Hirshman, S. P.; Lao, L. L.

2018-03-01

Large, spontaneous m/n  =  1/1 helical cores are shown to be expected in tokamaks such as ITER with extended regions of low- or reversed- magnetic shear profiles and q near 1 in the core. The threshold for this spontaneous symmetry breaking is determined using VMEC scans, beginning with reconstructed 3D equilibria from DIII-D and Alcator C-Mod based on observed internal 3D deformations. The helical core is a saturated internal kink mode (Wesson 1986 Plasma Phys. Control. Fusion 28 243); its onset threshold is shown to be proportional to (dp/dρ)/B_t2 around q  =  1. Below the threshold, applied 3D fields can drive a helical core to finite size, as in DIII-D. The helical core size thereby depends on the magnitude of the applied perturbation. Above it, a small, random 3D kick causes a bifurcation from axisymmetry and excites a spontaneous helical core, which is independent of the kick size. Systematic scans of the q-profile show that the onset threshold is very sensitive to the q-shear in the core. Helical cores occur frequently in Alcator C-Mod during ramp-up when slow current penetration results in a reversed shear q-profile, which is favorable for helical core formation. Finally, a comparison of the helical core onset threshold for discharges from DIII-D, Alcator C-Mod and ITER confirms that while DIII-D is marginally stable, Alcator C-Mod and especially ITER are highly susceptible to helical core formation without being driven by an externally applied 3D magnetic field.

Use of reconstructed 3D equilibria to determine onset conditions of helical cores in tokamaks for extrapolation to ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wingen, A.; Wilcox, R. S.; Seal, S. K.

In this paper, large, spontaneous m/n = 1/1 helical cores are shown to be expected in tokamaks such as ITER with extended regions of low- or reversed- magnetic shear profiles and q near 1 in the core. The threshold for this spontaneous symmetry breaking is determined using VMEC scans, beginning with reconstructed 3D equilibria from DIII-D and Alcator C-Mod based on observed internal 3D deformations. The helical core is a saturated internal kink mode (Wesson 1986 Plasma Phys. Control. Fusion 28 243); its onset threshold is shown to be proportional tomore » $$({\\rm d}p/{\\rm d}\\rho)/B_t^2$$ around q = 1. Below the threshold, applied 3D fields can drive a helical core to finite size, as in DIII-D. The helical core size thereby depends on the magnitude of the applied perturbation. Above it, a small, random 3D kick causes a bifurcation from axisymmetry and excites a spontaneous helical core, which is independent of the kick size. Systematic scans of the q-profile show that the onset threshold is very sensitive to the q-shear in the core. Helical cores occur frequently in Alcator C-Mod during ramp-up when slow current penetration results in a reversed shear q-profile, which is favorable for helical core formation. In conclusion, a comparison of the helical core onset threshold for discharges from DIII-D, Alcator C-Mod and ITER confirms that while DIII-D is marginally stable, Alcator C-Mod and especially ITER are highly susceptible to helical core formation without being driven by an externally applied 3D magnetic field.« less

Use of reconstructed 3D equilibria to determine onset conditions of helical cores in tokamaks for extrapolation to ITER

DOE PAGES

Wingen, A.; Wilcox, R. S.; Seal, S. K.; ...

2018-01-15

In this paper, large, spontaneous m/n = 1/1 helical cores are shown to be expected in tokamaks such as ITER with extended regions of low- or reversed- magnetic shear profiles and q near 1 in the core. The threshold for this spontaneous symmetry breaking is determined using VMEC scans, beginning with reconstructed 3D equilibria from DIII-D and Alcator C-Mod based on observed internal 3D deformations. The helical core is a saturated internal kink mode (Wesson 1986 Plasma Phys. Control. Fusion 28 243); its onset threshold is shown to be proportional tomore » $$({\\rm d}p/{\\rm d}\\rho)/B_t^2$$ around q = 1. Below the threshold, applied 3D fields can drive a helical core to finite size, as in DIII-D. The helical core size thereby depends on the magnitude of the applied perturbation. Above it, a small, random 3D kick causes a bifurcation from axisymmetry and excites a spontaneous helical core, which is independent of the kick size. Systematic scans of the q-profile show that the onset threshold is very sensitive to the q-shear in the core. Helical cores occur frequently in Alcator C-Mod during ramp-up when slow current penetration results in a reversed shear q-profile, which is favorable for helical core formation. In conclusion, a comparison of the helical core onset threshold for discharges from DIII-D, Alcator C-Mod and ITER confirms that while DIII-D is marginally stable, Alcator C-Mod and especially ITER are highly susceptible to helical core formation without being driven by an externally applied 3D magnetic field.« less

Toxic Shock Syndrome: An Unusual Organism.

PubMed

Young, Katie; Luni, Faraz Khan; Yoon, Youngsook

2016-07-01

Streptococcal toxic shock syndrome is a rapidly fatal disease causing hypotension with multi organ dysfunction (MODS) early in the course of infection, which by definition is caused by Group A streptococcus (GAS). We describe a case of Toxic Shock like Syndrome (TSLS) in which the causative organism was not a GAS. A 71-year-old woman with hepatitis C and primary biliary cirrhosis had sudden onset of slurred speech and left arm and facial numbness. She had bilateral erythematous macular rash present on the flanks and legs. She was started on empiric antibiotics but her condition rapidly deteriorated 6 hours after admission. During this time, the development of multiple large reddish-pink areas of ecchymosis with bullae on her lower extremities, flanks, and groin were noted. She also developed multiorgan dysfunction (MODS) with renal dysfunction, coagulopathy and liver involvement. Patient expired before surgery could be performed and the time from presentation to the time of death was 16 hours. The blood and bullae fluid cultures grew Streptococcus dysgalactiae equisimilis. Streptococcus dysgalactiae equisimilis is a rare cause of TSLS which typically affects elderly or immunocompromised patients and only a few cases have been described in the literature. Our patient met criteria for TSLS which caused rapid shock and MODS. We review the literature of the cases describing the clinical characteristics of TSLS cause by non-GAS. Group G Streptococci is a rare but lethal cause of streptococcal toxic shock syndrome. Copyright © 2016 Southern Society for Clinical Investigation. Published by Elsevier Inc. All rights reserved.

Present status and future prospect of coated conductor development and its application in Japan

NASA Astrophysics Data System (ADS)

Shiohara, Y.; Yoshizumi, M.; Izumi, T.; Yamada, Y.

2008-03-01

The current national project on coated conductors using Y-system superconductors has been carried out over the project period (FY2003-FY2007). In this paper, the current status and the future prospect of this project are reviewed. The high performance tape development group, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting layers on PLD-CeO2/IBAD-GZO buffered substrates. A high product of Ic and L, higher than 112 166 A m, was achieved in a 368 m-304.8 A GdBCO tape whose Ic value is mostly above 350 A/cm in width. The performance under magnetic field was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO2. 61 m long GdBCO tape with ZrO2 doping showed a high Ic value of 220 A at self field and 30 A at 3 T. On the other hand, another group focusing on low production cost has worked on TFA-MOD and MOCVD processes. The extremely high Ic value of 735 A/cm-w was obtained in TFA-MOD films on PLD-CeO2/IBAD-GZO/Hastelloy substrate due to the effect of Ba-poor nominal composition. In efforts towards long tape production by the SWCC group, a 200 m long tape with a high Ic value of 200 A/cm-w was obtained using a batch-type furnace. The Ic × L value of this tape was 40 000 A m, which is the highest value in the world obtained by the TFA-MOD process. Based on the above achievements in coated conductor process development, two new additional goals were set in the project. One is the development of extremely low cost tape and the other is the development of the basic technologies for making electric power devices of cables, transformers, motors, current-limiters and cryocoolers. Some of the new investigations have already revealed marvellous results, such as a 15 kW motor, low AC loss coils, low AC loss cables, etc.

MOD control center automated information systems security evolution

NASA Technical Reports Server (NTRS)

Owen, Rich

1991-01-01

The role of the technology infusion process in future Control Center Automated Information Systems (AIS) is highlighted. The following subject areas are presented in the form of the viewgraphs: goals, background, threat, MOD's AISS program, TQM, SDLC integration, payback, future challenges, and bottom line.

Alcator C-Mod Digital Plasma Control System

NASA Astrophysics Data System (ADS)

Wolfe, S. M.

2005-10-01

A new digital plasma control system (DPCS) has been implemented for Alcator C-Mod. The new system was put into service at the start of the 2005 run campaign and has been in routine operation since. The system consists of two 64-input, 16-output cPCI digitizers attached to a rack-mounted single-CPU Linux server, which performs both the I/O and the computation. During initial operation, the system was set up to directly emulate the original C-Mod ``Hybrid'' MIMO linear control system. Compatibility with the previous control system allows the existing user interface software and data structures to be used with the new hardware. The control program is written in IDL and runs under standard Linux. Interrupts are disabled during the plasma pulses to achieve real-time operation. A synchronous loop is executed with a nominal cycle rate of 10 kHz. Emulation of the original linear control algorithms requires 50 μsec per iteration, with the time evenly split between I/O and computation, so rates of about 20 KHz are achievable. Reliable vertical position control has been demonstrated with cycle rates as low as 5 KHz. Additional computations, including non-linear algorithms and adaptive response, are implemented as optional procedure calls within the main real-time loop.

Evidence for Chaotic Edge Turbulence in the Alcator C-Mod Tokamak

NASA Astrophysics Data System (ADS)

Zhu, Ziyan; White, Anne; Carter, Troy; Terry, Jim; Baek, Seung Gyou

2017-10-01

Turbulence greatly reduces the confinement time of magnetic-confined plasmas; understanding the nature of this turbulence and the associated transport is therefore of great importance. This research seeks to establish whether turbulent fluctuations in Alcator C-Mod are chaotic or stochastic. Stochastic fluctuations may lead to a random walk diffusive transport, whereas a diffusive description is unlikely to be valid for chaotic fluctuations since it lives in restricted areas of phase space (e.g., on attractors). Analysis of the time series obtained with the O-mode reflectometer and the gas puff imaging (GPI) systems reveals that the turbulent density fluctuations in C-Mod are chaotic. Supporting evidence for this conclusion includes the observation of an exponential power spectra (which is associated with Lorentzian-shaped pulses in the time series), the population of the corresponding Bandt-Pompe (BP) probability distribution, and the location of the signal on the Complexity-Entropy plane (C-H plane). These analysis techniques will be briefly introduced along with a discussion of the analysis results. The classification of edge turbulence as chaotic opens the door for further work to understand the underlying process and the impact on turbulent transport. Supported by USDoE awards DE-FC02-99ER54512 and DE-FC02-07ER54918:011.

A Spatially Resolving X-ray Crystal Spectrometer for Measurement of Ion-temperature and Rotation-velocity Profiles on the AlcatorC-Mod Tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, K. W.; Bitter, M. L.; Scott, S. D.

2009-03-24

A new spatially resolving x-ray crystal spectrometer capable of measuring continuous spatial profiles of high resolution spectra (λ/dλ > 6000) of He-like and H-like Ar Kα lines with good spatial (~1 cm) and temporal (~10 ms) resolutions has been installed on the Alcator C-Mod tokamak. Two spherically bent crystals image the spectra onto four two-dimensional Pilatus II pixel detectors. Tomographic inversion enables inference of local line emissivity, ion temperature (Ti), and toroidal plasma rotation velocity (vφ) from the line Doppler widths and shifts. The data analysis techniqu

An integrated charge exchange recombination spectroscopy/beam emission spectroscopy diagnostic for Alcator C-Mod tokamak.

PubMed

Bespamyatnov, I O; Rowan, W L; Liao, K T; Granetz, R S

2010-10-01

A novel integrated charge exchange recombination spectroscopy (CXRS)/beam emission spectroscopy (BES) system is proposed for C-Mod, in which both measurements are taken from a shared viewing geometry. The supplementary BES system serves to quantify local beam densities and supplants the common calculation of beam attenuation. The new system employs two optical viewing arrays, 20 poloidal and 22 toroidal channels. A dichroic filter splits the light between two spectrometers operating at different wavelengths for impurity ion and beam neutrals emission. In this arrangement, the impurity density is inferred from the electron density, measured BES and CXRS spectral radiances, and atomic emission rates.

Posttest RELAP5 simulations of the Semiscale S-UT series experiments. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leonard, M.T.

The RELAP5/MOD1 computer code was used to perform posttest calculations, simulating six experiments, run in the Semiscale Mod-2A facility, investigating the effects of upper head injection on small break transient behavior. The results of these calculations and corresponding test data are presented in this report. An evaluation is made of the capability of RELAP5 to calculate the thermal-hydraulic response of the Mod-2A system over a spectrum of break sizes, with and without the use of upper head injection.

Study of toroidal flow generation by ion cyclotron range of frequency minority heating in the Alcator C-Mod plasma

NASA Astrophysics Data System (ADS)

Murakami, S.; Itoh, K.; Zheng, L. J.; Van Dam, J. W.; Bonoli, P.; Rice, J. E.; Fiore, C. L.; Gao, C.; Fukuyama, A.

2016-01-01

The averaged toroidal flow of energetic minority ions during ICRF (ion cyclotron range of frequencies) heating is investigated in the Alcator C-Mod plasma by applying the GNET code, which can solve the drift kinetic equation with complicated orbits of accelerated energetic particles. It is found that a co-directional toroidal flow of the minority ions is generated in the region outside of the resonance location, and that the toroidal velocity reaches more than 40% of the central ion thermal velocity (Vtor ˜ 300 km/s with PICRF ˜ 2 MW). When we shift the resonance location to the outside of |r /a |˜0.5 , the toroidal flow immediately inside of the resonance location is reduced to 0 or changes to the opposite direction, and the toroidal velocity shear is enhanced at r/a ˜ 0.5. A radial diffusion equation for toroidal flow is solved by assuming a torque profile for the minority ion mean flow, and good agreements with experimental radial toroidal flow profiles are obtained. This suggests that the ICRF driven minority ion flow is related to the experimentally observed toroidal rotation during ICRF heating in the Alcator C-Mod plasma.

Impact of perturbative, non-axisymmetric impurity fueling on Alcator C-Mod H-modes

NASA Astrophysics Data System (ADS)

Reinke, M. L.; Lore, J. D.; Terry, J.; Brunner, D.; LaBombard, B.; Lipschultz, B.; Hubbard, A.; Hughes, J. W.; Mumgaard, R.; Pitts, R. A.

2017-12-01

Experiments on Alcator C-Mod have been performed to investigate the impact of toroidally localized impurity injection on H-mode exhaust scenarios. Results help to inform sub-divertor gas injector designs, in particular that of the ITER machine, for which this work was primarily undertaken. In repeated EDA H-modes, the amount of N2 injected into the private flux region was scanned up to levels which strongly impacted normalized energy confinement, H98, and led to an H/L back-transition. Repeated scans increased the toroidal peaking of the gas injection, reducing from five equally spaced locations to a single toroidal and poloidal injector. Results show the impact on the pedestal and core plasma is similar between all cases as long as the total gas injection rate is held constant. An influence on toroidally localized impurity spectroscopy is shown, demonstrating a complication in using such data in interpreting experiments and supporting boundary modeling in cases where there are localized extrinsic or intrinsic impurity sources. These results, along with prior work in this area on Alcator C-Mod, form a comprehensive set of L-mode and H-mode data to be used for validation of 3D boundary physics codes.

Observations of Rotation Reversal and Fluctuation Hysteresis in Alcator C-Mod L-Mode Plasmas

NASA Astrophysics Data System (ADS)

Cao, N. M.; Rice, J. E.; White, A. E.; Baek, S. G.; Creely, A. J.; Ennever, P. C.; Hubbard, A. E.; Hughes, J. W.; Irby, J.; Rodriguez-Fernandez, P.; Chilenski, M. A.; Diamond, P. H.; Reinke, M. L.; Alcator C-Mod Team

2017-10-01

Intrinsic core toroidal rotation in Alcator C-Mod L-mode plasmas has been observed to spontaneously reverse direction when the minimum value of the normalized collisionality ν*, crosses around 0.4. In Ohmic plasmas, the rotation is co-current in the low density linear Ohmic confinement (LOC) regime and counter-current in the higher density saturated Ohmic confinement (SOC) regime. The reversal manifests a hysteresis loop in ν*, where the critical collisionalities for the forward and reverse transitions differ by 10-15%. Temperature and density profiles of the two rotation states are observed to be indistinguishable to within experimental error estimated with Gaussian process regression. However, qualitative differences between the two rotation states are observed in fluctuation spectra, including the broadening of reflectometry spectra and, under certain conditions, the appearance of high-k features in phase contrast imaging (PCI) spectra (kθρs up to 1). These results suggest that the turbulent state can decouple from local profiles, and that turbulent self-regulation may play a role in the LOC/SOC transition. This work is supported by the US DOE under Grant DE-FC02-99ER54512 (C-Mod).

C-Mod MHD stability analysis with LHCD

NASA Astrophysics Data System (ADS)

Ebrahimi, Fatima; Bhattacharjee, A.; Delgado, L.; Scott, S.; Wilson, J. R.; Wallace, G. M.; Shiraiwa, S.; Mumgaard, R. T.

2016-10-01

In lower hybrid current drive (LHCD) experiments on the Alcator C-Mod, sawtooth activity could be suppressed as the safety factor q on axis is raised above unity. However, in some of these experiments, after applying LHCD, the onset of MHD mode activity caused the current drive efficiency to significantly drop. Here, we study the stability of these experiments by performing MHD simulations using the NIMROD code starting with experimental EFIT equilibria. First, consistent with the LHCD experiment with no signature of MHD activity, MHD mode activity was also absent in the simulations. Second, for experiments with MHD mode activity, we find that a core n=1 reconnecting mode with dominate poloidal modes of m=2,3 is unstable. This mode is a resistive current-driven mode as its growth rate scales with a negative power of the Lundquist number in the simulations. In addition, with further enhanced reversed-shear q profile in the simulations, a core double tearing mode is found to be unstable. This work is supported by U.S. DOE cooperative agreement DE-FC02-99ER54512 using the Alcator C-Mod tokamak, a DOE Office of Science user facility.

Influence of high magnetic field on access to stationary H-modes and pedestal characteristics in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Tolman, E. A.; Hughes, J. W.; Wolfe, S. M.; Wukitch, S. J.; LaBombard, B.; Hubbard, A. E.; Marmar, E. S.; Snyder, P. B.; Schmidtmayr, M.

2018-04-01

Recent Alcator C-Mod experiments have explored access to and characteristics of H-modes at magnetic fields approaching 8 T, the highest field achieved to date in a diverted tokamak. The H-modes originated from L-mode densities ranging from 1.1 × 1020~m-3 to 2.8 × 1020~m-3 , allowing insight into the density dependence of the H-mode power threshold at high magnetic field. This dependence is compared to predictions from the ITPA scaling law ([1]), finding that the law is approximately accurate at 7.8 T. However, the law underpredicted the high density H-mode threshold at lower magnetic field in previous C-Mod experiments ([2]), suggesting that the overall dependence of the threshold on magnetic field is weaker than predicted by the scaling law. The threshold data at 7.8 T also indicates that the onset of a low density branch at this magnetic field on C-Mod occurs below 1.4 × 1020~m-3 , which is lower than predicted by an existing model for low density branch onset. The H-modes achieved steady-state densities ranging from 2.3 × 1020 ~m-3 to 4.4 × 1020 ~m-3 , and higher transient densities, and had values of q 95 from 3.3 to 6.0. This parameter range allowed the achievement of all three types of H-mode routinely observed at lower magnetic field on C-Mod: the stationary, ELM-suppressed Enhanced D α (EDA) regime, seen at high densities and high values of q 95; the nonstationary ELM-free regime, seen at lower densities and values of q 95; and the ELMy regime, seen at low density, moderate q 95, and specialized plasma shape. The parameter space in which these regimes occur at 7.8 T is consistent with lower magnetic field experience. Pressure pedestal height at 7.8 T is compared to EPED [3, 4] predictions, and a scaling law for EDA density pedestal height developed between 4.5 T and 6.0 T is updated to include fields from 2.7 T to 7.8 T. Overall, this analysis increases confidence in the use of low magnetic field experience to predict some elements of high magnetic field tokamak behavior.

NOX2 protects against progressive lung injury and multiple organ dysfunction syndrome.

PubMed

Whitmore, Laura C; Goss, Kelli L; Newell, Elizabeth A; Hilkin, Brieanna M; Hook, Jessica S; Moreland, Jessica G

2014-07-01

Systemic inflammatory response syndrome (SIRS) is a common clinical condition in patients in intensive care units that can lead to complications, including multiple organ dysfunction syndrome (MODS). MODS carries a high mortality rate, and it is unclear why some patients resolve SIRS, whereas others develop MODS. Although oxidant stress has been implicated in the development of MODS, several recent studies have demonstrated a requirement for NADPH oxidase 2 (NOX2)-derived oxidants in limiting inflammation. We recently demonstrated that NOX2 protects against lung injury and mortality in a murine model of SIRS. In the present study, we investigated the role of NOX2-derived oxidants in the progression from SIRS to MODS. Using a murine model of sterile systemic inflammation, we observed significantly greater illness and subacute mortality in gp91(phox-/y) (NOX2-deficient) mice compared with wild-type mice. Cellular analysis revealed continued neutrophil recruitment to the peritoneum and lungs of the NOX2-deficient mice and altered activation states of both neutrophils and macrophages. Histological examination showed multiple organ pathology indicative of MODS in the NOX2-deficient mice, and several inflammatory cytokines were elevated in lungs of the NOX2-deficient mice. Overall, these data suggest that NOX2 function protects against the development of MODS and is required for normal resolution of systemic inflammation. Copyright © 2014 the American Physiological Society.

Assessment of PWR Steam Generator modelling in RELAP5/MOD2. International Agreement Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Putney, J.M.; Preece, R.J.

1993-06-01

An assessment of Steam Generator (SG) modelling in the PWR thermal-hydraulic code RELAP5/MOD2 is presented. The assessment is based on a review of code assessment calculations performed in the UK and elsewhere, detailed calculations against a series of commissioning tests carried out on the Wolf Creek PWR and analytical investigations of the phenomena involved in normal and abnormal SG operation. A number of modelling deficiencies are identified and their implications for PWR safety analysis are discussed -- including methods for compensating for the deficiencies through changes to the input deck. Consideration is also given as to whether the deficiencies willmore » still be present in the successor code RELAP5/MOD3.« less

Measurement and prediction of broadband noise from large horizontal axis wind turbine generators

NASA Technical Reports Server (NTRS)

Grosveld, F. W.; Shepherd, K. P.; Hubbard, H. H.

1995-01-01

A method is presented for predicting the broadband noise spectra of large wind turbine generators. It includes contributions from such noise sources as the inflow turbulence to the rotor, the interactions between the turbulent boundary layers on the blade surfaces with their trailing edges and the wake due to a blunt trailing edge. The method is partly empirical and is based on acoustic measurements of large wind turbines and airfoil models. Spectra are predicted for several large machines including the proposed MOD-5B. Measured data are presented for the MOD-2, the WTS-4, the MOD-OA, and the U.S. Windpower Inc. machines. Good agreement is shown between the predicted and measured far field noise spectra.

A multi-machine scaling of halo current rotation

NASA Astrophysics Data System (ADS)

Myers, C. E.; Eidietis, N. W.; Gerasimov, S. N.; Gerhardt, S. P.; Granetz, R. S.; Hender, T. C.; Pautasso, G.; Contributors, JET

2018-01-01

Halo currents generated during unmitigated tokamak disruptions are known to develop rotating asymmetric features that are of great concern to ITER because they can dynamically amplify the mechanical stresses on the machine. This paper presents a multi-machine analysis of these phenomena. More specifically, data from C-Mod, NSTX, ASDEX Upgrade, DIII-D, and JET are used to develop empirical scalings of three key quantities: (1) the machine-specific minimum current quench time, \

A multi-machine scaling of halo current rotation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myers, C. E.; Eidietis, N. W.; Gerasimov, S. N.

Halo currents generated during unmitigated tokamak disruptions are known to develop rotating asymmetric features that are of great concern to ITER because they can dynamically amplify the mechanical stresses on the machine. This paper presents a multi-machine analysis of these phenomena. More specifically, data from C-Mod, NSTX, ASDEX Upgrade, DIII-D, and JET are used to develop empirical scalings of three key quantities: the machine-specific minimum current quench time,more » $$ \

A multi-machine scaling of halo current rotation

DOE PAGES

Myers, C. E.; Eidietis, N. W.; Gerasimov, S. N.; ...

2017-12-12

Halo currents generated during unmitigated tokamak disruptions are known to develop rotating asymmetric features that are of great concern to ITER because they can dynamically amplify the mechanical stresses on the machine. This paper presents a multi-machine analysis of these phenomena. More specifically, data from C-Mod, NSTX, ASDEX Upgrade, DIII-D, and JET are used to develop empirical scalings of three key quantities: the machine-specific minimum current quench time,more » $$ \

Investigation of the transport shortfall in Alcator C-Mod L-mode plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, N. T.; White, A. E.; Greenwald, M.

2013-03-15

A so-called 'transport shortfall,' where ion and electron heat fluxes and turbulence are underpredicted by gyrokinetic codes, has been robustly identified in DIII-D L-mode plasmas for {rho}>0.55[T. L. Rhodes et al., Nucl. Fusion 51(6), 063022 (2011); and C. Holland et al., Phys. Plasmas 16(5), 052301 (2009)]. To probe the existence of a transport shortfall across different tokamaks, a dedicated scan of auxiliary heated L-mode discharges in Alcator C-Mod are studied in detail with nonlinear gyrokinetic simulations for the first time. Two discharges, only differing by the amount of auxiliary heating are investigated using both linear and nonlinear simulation of themore » GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)]. Nonlinear gyrokinetic simulation of the low and high input power discharges reveals a discrepancy between simulation and experiment in only the electron heat flux channel of the low input power discharge. However, both discharges demonstrate excellent agreement in the ion heat flux channel, and the high input power discharge demonstrates simultaneous agreement with experiment in both the electron and ion heat flux channels. A summary of linear and nonlinear gyrokinetic results and a discussion of possible explanations for the agreement/disagreement in each heat flux channel is presented.« less

A biphasic epigenetic switch controls immunoevasion, virulence and niche adaptation in non-typeable Haemophilus influenzae.

PubMed

Atack, John M; Srikhanta, Yogitha N; Fox, Kate L; Jurcisek, Joseph A; Brockman, Kenneth L; Clark, Tyson A; Boitano, Matthew; Power, Peter M; Jen, Freda E-C; McEwan, Alastair G; Grimmond, Sean M; Smith, Arnold L; Barenkamp, Stephen J; Korlach, Jonas; Bakaletz, Lauren O; Jennings, Michael P

2015-07-28

Non-typeable Haemophilus influenzae contains an N(6)-adenine DNA-methyltransferase (ModA) that is subject to phase-variable expression (random ON/OFF switching). Five modA alleles, modA2, modA4, modA5, modA9 and modA10, account for over two-thirds of clinical otitis media isolates surveyed. Here, we use single molecule, real-time (SMRT) methylome analysis to identify the DNA-recognition motifs for all five of these modA alleles. Phase variation of these alleles regulates multiple proteins including vaccine candidates, and key virulence phenotypes such as antibiotic resistance (modA2, modA5, modA10), biofilm formation (modA2) and immunoevasion (modA4). Analyses of a modA2 strain in the chinchilla model of otitis media show a clear selection for ON switching of modA2 in the middle ear. Our results indicate that a biphasic epigenetic switch can control bacterial virulence, immunoevasion and niche adaptation in an animal model system.

A Functional Genomics Approach to Identify Novel Breast Cancer Gene Targets in Yeast

DTIC Science & Technology

2005-05-01

Chaleff DT, Valent B, Fink GR. Mutations affecting Ty-mediated expression of the HIS4 gene of Saccharomyces cerevisiae. Genetics 1984; 107(2): 179-97... mutations , and are synthetically lethal with rotl mutations ROX3 YBL093C Repressor Of hypoXic genes : RNA polymerase I1 holcenzyme component 3,3 SSS...mitochondrial gene products; mutation causes an elevated rate of mitochondrial turnover; 3 MOD after 60 generations, MOD on NaCI YNDI YER005W Yeast Nucleoside

F-22 Increment 3.2B Modernization (F-22 Inc 3.2B Mod)

DTIC Science & Technology

2013-12-01

MAR 2016 SEP 2016 SEP 2016 (Ch-1) Full Rate Production JAN 2018 JAN 2018 JUL 2018 JUL 2018 (Ch-1) Required Assets Available ( RAA ) MAR 2019 MAR 2019 SEP...2019 SEP 2019 (Ch-1) Change Explanations (Ch-1) The Milestone C, Full Rate Production, and Required Assets Available ( RAA ) current estimates changed...successful. Memo RAA is defined as six aircraft and associated support equipment. F-22 Inc 3.2B Mod December 2013 SAR April 16, 2014 17:04:43

Advanced multi-megawatt wind turbine design for utility application

NASA Technical Reports Server (NTRS)

Pijawka, W. C.

1984-01-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

Advanced multi-megawatt wind turbine design for utility application

NASA Astrophysics Data System (ADS)

Pijawka, W. C.

1984-08-01

A NASA/DOE program to develop a utility class multimegawatt wind turbine, the MOD-5A, is described. The MOD-5A features a 400 foot diameter rotor which is teetered and positioned upwind of the tower; a 7.3 megawatt power rating with a variable speed electric generating system; and a redundant rotor support and torque transmission structure. The rotor blades were fabricated from an epoxy-bonded wood laminate material which was a successful outgrowth of the MOD-OA airfoil design. Preliminary data from operational tests carried out at the NASA Plumbrook test facility are presented.

MOD silver metallization for photovoltaics

NASA Technical Reports Server (NTRS)

Vest, G. M.; Vest, R. W.

1984-01-01

The development of flat plate solar arrays is reported. Photovoltaic cells require back side metallization and a collector grid system on the front surface. Metallo-organic decomposition (MOD) silver films can eliminate most of the present problems with silver conductors. The objectives are to: (1) identify and characterize suitable MO compounds; (2) develop generic synthesis procedures for the MO compounds; (3) develop generic fabrication procedures to screen printable MOD silver inks; (4) optimize processing conditions to produce grid patterns and photovoltaic cells; and (5) develop a model which describes the adhesion between the fired silver film and the silicon surface.

NASA Glenn Icing Research Tunnel: 2014 and 2015 Cloud Calibration Procedures and Results

NASA Technical Reports Server (NTRS)

Steen, Laura E.; Ide, Robert F.; Van Zante, Judith F.; Acosta, Waldo J.

2015-01-01

This report summarizes the current status of the NASA Glenn Research Center (GRC) Icing Research Tunnel cloud calibration: specifically, the cloud uniformity, liquid water content, and drop-size calibration results from both the January-February 2014 full cloud calibration and the January 2015 interim cloud calibration. Some aspects of the cloud have remained the same as what was reported for the 2014 full calibration, including the cloud uniformity from the Standard nozzles, the drop-size equations for Standard and Mod1 nozzles, and the liquid water content for large-drop conditions. Overall, the tests performed in January 2015 showed good repeatability to 2014, but there is new information to report as well. There have been minor updates to the Mod1 cloud uniformity on the north side of the test section. Also, successful testing with the OAP-230Y has allowed the IRT to re-expand its operating envelopes for large-drop conditions to a maximum median volumetric diameter of 270 microns. Lastly, improvements to the collection-efficiency correction for the SEA multi-wire have resulted in new calibration equations for Standard- and Mod1-nozzle liquid water content.

Experiment data report for Semiscale Mod-1 Test S-05-1 (alternate ECC injection test)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, E. M.; Patton, Jr., M. L.; Sackett, K. E.

Recorded test data are presented for Test S-05-1 of the Semiscale Mod-1 alternate ECC injection test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-05-1 was conducted from initial conditions of 2263 psia and 544/sup 0/F to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the cold leg broken loop piping. During the test, cooling water was injected into the vessel lower plenum to simulatemore » emergency core coolant injection in a PWR, with the flow rate based on system volume scaling.« less

Moderate Resolution Imaging Spectroradiometer (MODIS) MOD21 Land Surface Temperature and Emissivity Algorithm Theoretical Basis Document

NASA Technical Reports Server (NTRS)

Hulley, G.; Malakar, N.; Hughes, T.; Islam, T.; Hook, S.

2016-01-01

This document outlines the theory and methodology for generating the Moderate Resolution Imaging Spectroradiometer (MODIS) Level-2 daily daytime and nighttime 1-km land surface temperature (LST) and emissivity product using the Temperature Emissivity Separation (TES) algorithm. The MODIS-TES (MOD21_L2) product, will include the LST and emissivity for three MODIS thermal infrared (TIR) bands 29, 31, and 32, and will be generated for data from the NASA-EOS AM and PM platforms. This is version 1.0 of the ATBD and the goal is maintain a 'living' version of this document with changes made when necessary. The current standard baseline MODIS LST products (MOD11*) are derived from the generalized split-window (SW) algorithm (Wan and Dozier 1996), which produces a 1-km LST product and two classification-based emissivities for bands 31 and 32; and a physics-based day/night algorithm (Wan and Li 1997), which produces a 5-km (C4) and 6-km (C5) LST product and emissivity for seven MODIS bands: 20, 22, 23, 29, 31-33.

Relation of antioxidant status at admission and disease severity and outcome in dogs naturally infected with Babesia canis canis.

PubMed

Crnogaj, Martina; Cerón, José Joaquin; Šmit, Iva; Kiš, Ivana; Gotić, Jelena; Brkljačić, Mirna; Matijatko, Vesna; Rubio, Camila Peres; Kučer, Nada; Mrljak, Vladimir

2017-04-24

Canine babesiosis is caused by species of the Babesia genus and has become an emerging disease worldwide. To the authors' knowledge there are no reports in which antioxidants have been analyzed in different presentations of canine babesiosis or in which the prognostic value of antioxidants has been studied. The aim of this study was to evaluate whether oxidative stress could be related to the severity and outcome of canine babesiosis. For this purpose a profile consisting of four antioxidant biomarkers (superoxide dismutase - SOD, glutathione peroxidase - GPx, catalase, total antioxidant status - TAS) and malondialdehyde - MDA as an oxidant biomarker (previously evaluated, here studied for comparative purposes) were evaluated in dogs with canine babesiosis of different clinical severity and outcomes. The study was conducted with a sample of 40 dogs suffering from babesiosis (further divided into uncomplicated, one complication and multiple organ dysfunction syndrome - MODS group) and 30 healthy dogs (control group). Additionally, the babesiosis group was divided according to the anaemia into non-anaemic, mildly anaemic, moderately anaemic and severely anaemic dogs. The results of our study showed significantly decreased SOD, catalase and TAS values in diseased dogs compared to controls, while there were no significant differences in GPx between these groups. Dogs that developed MODS showed lower activities of SOD and GPx and higher MDA values compared to dogs with uncomplicated babesiosis as well as with dogs that developed one complication. Superoxide dismutase, catalase and GPx were negatively correlated whereas MDA was positively correlated with the lethal outcome of the disease. Furthermore, this study detected more pronounced decrease in antioxidant biomarkers (SOD, GPx and catalase) in dogs with moderate anaemia compared to those with mild anaemia. The results of this study showed changes in biomarkers related to the antioxidant status of dogs naturally infected with B. canis canis. These biomarkers could be used as indicators of disease severity and outcome in dogs suffering from babesiosis.

RF current profile control studies in the alcator C-mod tokamak

NASA Astrophysics Data System (ADS)

Bonoli, P. T.; Porkolab, M.; Wukitch, S. J.; Bernabei, S.; Kaita, R.; Mikkelsen, D.; Phillips, C. K.; Schilling, G.

1999-09-01

Time dependent calculations of lower hybrid (LH) current profile control in Alcator C-Mod have been done using the TRANSP [1], FPPRF [2], and LSC [3] codes. Up to 3 MW of LH current drive power was applied in plasmas with high power ICRF minority heating (PICH=1.8-3 MW) and fast current ramp up. Using the experimentally measured temperature profiles, off-axis current generation resulted in nonmonotonic q-profiles with qmin~=1.6. Self-consistent effects of off-axis electron heating by the LH power were also included in the analysis and significant broadening of the electron temperature profile was found with qmin>~2 and a larger shear reversal radius.

High-performance finite-difference time-domain simulations of C-Mod and ITER RF antennas

NASA Astrophysics Data System (ADS)

Jenkins, Thomas G.; Smithe, David N.

2015-12-01

Finite-difference time-domain methods have, in recent years, developed powerful capabilities for modeling realistic ICRF behavior in fusion plasmas [1, 2, 3, 4]. When coupled with the power of modern high-performance computing platforms, such techniques allow the behavior of antenna near and far fields, and the flow of RF power, to be studied in realistic experimental scenarios at previously inaccessible levels of resolution. In this talk, we present results and 3D animations from high-performance FDTD simulations on the Titan Cray XK7 supercomputer, modeling both Alcator C-Mod's field-aligned ICRF antenna and the ITER antenna module. Much of this work focuses on scans over edge density, and tailored edge density profiles, to study dispersion and the physics of slow wave excitation in the immediate vicinity of the antenna hardware and SOL. An understanding of the role of the lower-hybrid resonance in low-density scenarios is emerging, and possible implications of this for the NSTX launcher and power balance are also discussed. In addition, we discuss ongoing work centered on using these simulations to estimate sputtering and impurity production, as driven by the self-consistent sheath potentials at antenna surfaces.

High-Performance Computational Modeling of ICRF Physics and Plasma-Surface Interactions in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Jenkins, Thomas; Smithe, David

2016-10-01

Inefficiencies and detrimental physical effects may arise in conjunction with ICRF heating of tokamak plasmas. Large wall potential drops, associated with sheath formation near plasma-facing antenna hardware, give rise to high-Z impurity sputtering from plasma-facing components and subsequent radiative cooling. Linear and nonlinear wave excitations in the plasma edge/SOL also dissipate injected RF power and reduce overall antenna efficiency. Recent advances in finite-difference time-domain (FDTD) modeling techniques allow the physics of localized sheath potentials, and associated sputtering events, to be modeled concurrently with the physics of antenna near- and far-field behavior and RF power flow. The new methods enable time-domain modeling of plasma-surface interactions and ICRF physics in realistic experimental configurations at unprecedented spatial resolution. We present results/animations from high-performance (10k-100k core) FDTD/PIC simulations spanning half of Alcator C-Mod at mm-scale resolution, exploring impurity production due to localized sputtering (in response to self-consistent sheath potentials at antenna surfaces) and the physics of parasitic slow wave excitation near the antenna hardware and SOL. Supported by US DoE (Award DE-SC0009501) and the ALCC program.

Application of a MODIS Soil Moisture-Evapotranspiration (MOD-SMET) Model to Evaluate Landscape and Hydrologic Recovery after the High Park Fire in Colorado, USA

NASA Astrophysics Data System (ADS)

Blount, W. K.; Hogue, T. S.; Franz, K.; Knipper, K. R.

2017-12-01

Accurate estimation of evapotranspiration (ET) is critical for the management of water resources, especially in water-stressed regions. ET accounts for approximately 60% of terrestrial precipitation globally and approaches 100% of annual rainfall in arid ecosystems, where transpiration becomes the dominant term. ET is difficult to measure due to its spatiotemporal variation, which requires adequate data coverage. While new remote sensing-based ET products are available at a 1 km spatial resolution, including the Operational Simplified Surface Energy Balance model (SSEBop) and the MODIS Global Evapotranspiration Project (MOD16), these products are available at monthly and 8-day temporal resolutions, respectively. To better understand the changing dynamics of hydrologic fluxes and the partitioning of water after land cover disturbances and to identify statically significant trends, more frequent observations are necessary. Utilizing the recently developed MODIS Soil Moisture-Evapotranspiration (MOD-SMET) model, daily temporal resolution is achieved. This presentation outlines the methodology of the MOD-SMET model and compares SSEBop, MOD16, and MOD-SMET ET estimates over the High Park Fire burn scar in Colorado, USA. MOD-SMET estimates are used to identify changes in fluxes and partitioning of the water cycle after a wildfire and during recovery in the High Park Fire near Fort Collins, Colorado. Initial results indicate greenness and ET from all three models decrease post-fire, with higher statistical confidence in high burn areas and spatial patterns that closely align with burn severity. MOD-SMET improves the ability to resolve statistically significant changes in ET following wildfires and better understand changes in the post-fire water budget. Utilizing this knowledge, water resource managers can better plan for, and mitigate, the short- and long-term impacts of wildfire on regional water supplies.

Evaluation of the MODIS Collections 005 and 006 for Change Detection of Vegetation Dynamics in North and South America

NASA Astrophysics Data System (ADS)

Heck, E. J.; Owsley, B.; Henebry, G. M.; de Beurs, K.

2017-12-01

Since the beginning of the MODIS data record in 2000, several improvements have been made to all available products. Currently, the MODIS community is in the process of completing the roll out of collection 6. While the community takes great interest in data continuity models, less attention has been given to how the changes that are carried out between collections impact the findings of earlier analyses. Here, we assess differences between change detection results from Collection 005 and 006 of the Nadir BRDF-Adjusted Reflectance product (MCD43), the Gridded Vegetation Indices product (MOD13) and the Land Surface Temperature product (MOD11), all at 0.05-degree resolution across the Western Hemisphere. We applied the non-parametric Seasonal-Kendall trend test to time series from C005 and C006 to identify areas of significant change during the period 2001-2016. We analyzed the significant trends and the differences between collections by country, by IGBP land cover class, and by the Human Impact Index category. Preliminary results from the MOD13 product indicate agreement between C005 and C006 for 65% of the pixels when investigating EVI trends and 74% of the pixels when investigating NDVI trends. Only 1% of the pixels reveal a full disagreement in the signal of the significance trends, e.g. negative trend in C005 paired with a positive trend in C006. Though the percentage of complete reversal is low, there are variations of discrepancies between collections that are consistent between both the MOD13 and MCD43 products. For example, while almost 18% of the pixels revealed a significant browning in C005, only 5.80% of the pixels revealed significant browning in both collections. We found that 11% of the pixels with significant browning in C005, were stable in C006. Vice versa, we found that 19.18% of all pixels revealed a significant positive trend in C006 while these pixels were stable in C005. Even though C006 reveals more than double the percentage of positive trends (from 12% in C005 to 32% in C006), the large clusters of significant trends appear in the same spatial regions. We did not find similar drastic differences between collections when analyzing the trend results based on the Land Surface Temperature product. However, some key areas, such as the Amazon region, reveal significant differences.

Evaluation of the MODIS Collections 005 and 006 for Change Detection of Vegetation Dynamics in North and South America

NASA Astrophysics Data System (ADS)

Heck, E. J.; Owsley, B.; Henebry, G. M.; de Beurs, K.

2016-12-01

Since the beginning of the MODIS data record in 2000, several improvements have been made to all available products. Currently, the MODIS community is in the process of completing the roll out of collection 6. While the community takes great interest in data continuity models, less attention has been given to how the changes that are carried out between collections impact the findings of earlier analyses. Here, we assess differences between change detection results from Collection 005 and 006 of the Nadir BRDF-Adjusted Reflectance product (MCD43), the Gridded Vegetation Indices product (MOD13) and the Land Surface Temperature product (MOD11), all at 0.05-degree resolution across the Western Hemisphere. We applied the non-parametric Seasonal-Kendall trend test to time series from C005 and C006 to identify areas of significant change during the period 2001-2016. We analyzed the significant trends and the differences between collections by country, by IGBP land cover class, and by the Human Impact Index category. Preliminary results from the MOD13 product indicate agreement between C005 and C006 for 65% of the pixels when investigating EVI trends and 74% of the pixels when investigating NDVI trends. Only 1% of the pixels reveal a full disagreement in the signal of the significance trends, e.g. negative trend in C005 paired with a positive trend in C006. Though the percentage of complete reversal is low, there are variations of discrepancies between collections that are consistent between both the MOD13 and MCD43 products. For example, while almost 18% of the pixels revealed a significant browning in C005, only 5.80% of the pixels revealed significant browning in both collections. We found that 11% of the pixels with significant browning in C005, were stable in C006. Vice versa, we found that 19.18% of all pixels revealed a significant positive trend in C006 while these pixels were stable in C005. Even though C006 reveals more than double the percentage of positive trends (from 12% in C005 to 32% in C006), the large clusters of significant trends appear in the same spatial regions. We did not find similar drastic differences between collections when analyzing the trend results based on the Land Surface Temperature product. However, some key areas, such as the Amazon region, reveal significant differences.

Conceptual design of the 6 MW Mod-5A wind turbine generator

NASA Technical Reports Server (NTRS)

Barton, R. S.; Lucas, W. C.

1982-01-01

The General Electric Company, Advanced Energy Programs Department, is designing under DOE/NASA sponsorship the MOD-5A wind turbine system which must generate electricity for 3.75 cent/KWH (1980) or less. During the Conceptual Design Phase, completed in March, 1981, the MOD-5A WTG system size and features were established as a result of tradeoff and optimization studies driven by minimizing the system cost of energy (COE). This led to a 400' rotor diameter size. The MOD-5A system which resulted is defined in this paper along with the operational and environmental factors that drive various portions of the design. Development of weight and cost estimating relationships (WCER's) and their use in optimizing the MOD-5A are discussed. The results of major tradeoff studies are also presented. Subsystem COE contributions for the 100th unit are shown along with the method of computation. Detailed descriptions of the major subsystems are given, in order that the results of the various trade and optimization studies can be more readily visualized.

Perturbative transport modeling and comparison to cold-pulse and heat-pulse propagation experiments in Alcator C-Mod and DIII-D

NASA Astrophysics Data System (ADS)

Rodriguez Fernandez, P.; White, A. E.; Cao, N. M.; Creely, A. J.; Greenwald, M. J.; Howard, N. T.; Hubbard, A. E.; Hughes, J. W.; Irby, J. H.; Petty, C. C.; Rice, J. E.; Alcator C-Mod Team

2016-10-01

Possible ``non-local'' transport phenomena are often observed in tokamak plasmas. Different models have been proposed to explain fast responses during perturbative transport experiments, including non-diffusive effects. Specific tools to characterize the dynamic behavior and power balance analysis using TRANSP and the quasi-linear trapped gyro-landau fluid code TGLF have been developed to analyze Alcator C-Mod experiments. Recent results from cold pulse experiments show that fast core temperature increases following edge cold-pulse injections (peak within 10ms , while τE 25ms) are not correlated with the direction of intrinsic rotation, and instead the amplitude of the core response depends on density, plasma current and RF input power. The propagation of the cold pulse can be compared with propagation of heat pulses from sawteeth, and both may be used to probe changes in temperature profile stiffness. A Laser Blow Off (LBO) system is being developed for DIII-D that will allow further validation and cross-machine comparison of cold pulse experiments. LBO at DIII-D will also allow for direct comparisons with ECH perturbative heat pulse experiments. Work supported by US DOE under Grants DE-FC02-99ER54512 (C-Mod) and DE-FC02-04ER54698 (DIII-D) and La Caixa Fellowship.

Transport and Stability in C-Mod ITBs in Diverse Regimes

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Ernst, D. R.; Howard, N. T.; Kasten, C. P.; Mikkelsen, D.; Reinke, M. L.; Rice, J. E.; White, A. E.; Rowan, W. L.; Bespamyatnov, I.

2012-10-01

Internal Transport Barriers (ITBs) in C-Mod feature highly peaked density and pressure profiles and are typically induced by the introduction of radio frequency power in the ion cyclotron range of frequencies (ICRF) with the second harmonic of the resonance for minority hydrogen ions positioned off-axis at the plasma half radius on either the low or high field side of the plasma. These ITBs are formed in the absence of particle or momentum injection, and with monotonic q profiles with qmin< 1. Thus they allow exploration of ITB dynamics in a reactor relevant regime. Recently, linear and non-linear gyrokinetic simulations have demonstrated that changes in the ion temperature and plasma rotation profiles, coincident with the application of off-axis ICRF heating, contribute to greater stability to ion temperature gradient driven fluctuation in the plasma. This results in reduced turbulent driven outgoing heat flux. To date, ITB formation in C-Mod has only been observed in EDA H-mode plasmas with moderate (2-3 MW) ICRF power. Experiments to explore the formation of ITBs in other operating regimes such as I-mode and also with high ICRF power are being undertaken to understand further the process of ITB formation and sustainment, especially with regard to turbulent driven transport.

Fast imaging of filaments in the X-point region of Alcator C-Mod

DOE PAGES

Terry, J. L.; Ballinger, S.; Brunner, D.; ...

2017-01-27

A rich variety of field-aligned fluctuations has been revealed using fast imaging of D α emission from Alcator C-Mod's lower X-point region. Field-aligned filamentary fluctuations are observed along the inner divertor leg, within the Private-Flux-Zone (PFZ), in the Scrape-Off Layer (SOL) outside the outer divertor leg, and, under some conditions, at or above the X-point. The locations and dynamics of the filaments in these regions are strikingly complex in C-Mod. Changes in the filaments’ generation appear to be ordered by plasma density and magnetic configuration. Filaments are not observed for plasmas with n/nGreenwald ≲ 0.12 nor are they observed inmore » Upper Single Null configurations. In a Lower Single Null with 0.12 ≲ n/nGreenwald ≲ 0.45 and Bx∇B directed down, filaments typically move up the inner divertor leg toward the X-point. Reversing the field direction results in the appearance of filaments outside of the outer divertor leg. With the divertor targets “detached”, filaments inside the LCFS are seen. Lastly, these studies were motivated by observations of filaments in the X-point and PFZ regions in MAST, and comparisons with those observations are made.« less

Production of Internal Transport Barriers via self-generated flows in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Fiore, Catherine L.

2011-10-01

New results suggest that changes observed in the intrinsic toroidal rotation influence ITB formation in Alcator C-Mod that arise when the resonance for ICRF minority heating is positioned off-axis at or outside of the plasma half-radius. These ITBs form in a reactor relevant regime, without particle or momentum injection, with Ti ~Te, and with monotonic q profiles (qmin < 1). C-Mod H-mode plasmas exhibit strong intrinsic co-current rotation that increases with increasing stored energy without external drive. With the resonance position off-axis, the rotation decreases in the center of the plasma resulting in a radial rotation profile with a central well which deepens and moves farther off-axis when the ICRF resonance is at the plasma half-radius. This profile results in strong ExB shear (>1.5x105 Rad/sec) in the region where the ITB foot is observed. The self generated ExB shearing increases rapidly after the H-mode transition in off-axis ICRF heated discharges, before other profile changes are observed. Gyrokinetic analyses indicate that this spontaneous shearing rate is comparable to the linear ITG growth rate at the ITB location and may be responsible for stabilizing the underlying turbulence. Detailed measurement of the ion temperature demonstrates that the radial profile also flattens as the ICRF resonance position moves off axis. This decreases R/LTi in the barrier region, lessening the drive for the ITG turbulence and the resulting particle transport. The reduction in particle transport resulting from increase in core stability allows the neoclassical pinch to peak the density and pressure on axis. This suggests that spontaneous rotation is a potential tool for plasma profile control in reactor plasmas. The experimental results and corresponding gyrokinetic study will be presented. US-DoE DE-FC02-99ER54512 and DE-FG03-96ER54373.

Association of low non-invasive near-infrared spectroscopic measurements during initial trauma resuscitation with future development of multiple organ dysfunction.

PubMed

Nicks, Bret A; Campons, Kevin M; Bozeman, William P

2015-01-01

Near-infrared spectroscopy (NIRS) non-invasively monitors muscle tissue oxygen saturation (StO2). It may provide a continuous noninvasive measurement to identify occult hypoperfusion, guide resuscitation, and predict the development of multiple organ dysfunction (MOD) after severe trauma. We evaluated the correlation between initial StO2 and the development of MOD in multi-trauma patients. Patients presenting to our urban, academic, Level I Trauma Center/Emergency Department and meeting standardized trauma-team activation criteria were enrolled in this prospective trial. NIRS monitoring was initiated immediately on arrival with collection of StO2 at the thenar eminence and continued up to 24 hours for those admitted to the Trauma Intensive Care Unit (TICU). Standardized resuscitation laboratory measures and clinical evaluation tools were collected. The primary outcome was the association between initial StO2 and the development of MOD within the first 24 hours based on a MOD score of 6 or greater. Descriptive statistical analyses were performed; numeric means, multivariate regression and rank sum comparisons were utilized. Clinicians were blinded from the StO2 values. Over a 14 month period, 78 patients were enrolled. Mean age was 40.9 years (SD 18.2), 84.4% were male, 76.9% had a blunt trauma mechanism and mean injury severity score (ISS) was 18.5 (SD 12.9). Of the 78 patients, 26 (33.3%) developed MOD within the first 24 hours. The MOD patients had mean initial StO2 values of 53.3 (SD 10.3), significantly lower than those of non-MOD patients 61.1 (SD 10.0); P=0.002. The mean ISS among MOD patients was 29.9 (SD 11.5), significantly higher than that of non-MODS patients, 12.1 (SD 9.1) (P<0.0001). The mean shock index (SI) among MOD patients was 0.92 (SD 0.28), also significantly higher than that of non-MODS patients, 0.73 (SD 0.19) (P=0.0007). Lactate values were not significantly different between groups. Non-invasive, continuous StO2 near-infrared spectroscopy values during initial trauma resuscitation correlate with the later development of multiple organ dysfunction in this patient population.

An overview and the current status of instrumentation at the Large Binocular Telescope Observatory

NASA Astrophysics Data System (ADS)

Wagner, R. Mark; Edwards, Michelle L.; Kuhn, Olga; Thompson, David; Veillet, Christian

2014-07-01

An overview of instrumentation for the Large Binocular Telescope (LBT) is presented. Optical instrumentation includes the Large Binocular Camera (LBC), a pair of wide-field (24' × 24') mosaic CCD imagers at the prime focus, and the Multi-Object Double Spectrograph (MODS), a pair of dual-beam blue-red optimized long-slit spectrographs mounted at the left and right direct F/15 Gregorian foci incorporating multiple slit masks for multi-object spectroscopy over a 6' field and spectral resolutions of up to 2000. Infrared instrumentation includes the LBT Near-IR Spectrometer (LUCI), a modular near-infrared (0.9-2.5 μm) imager and spectrograph pair mounted at the left and right front-bent F/15 Gregorian foci and designed for seeing-limited (FOV: 4' × 4') imaging, long-slit spectroscopy, and multi-object spectroscopy utilizing cooled slit masks and diffraction limited (FOV: 0'.5 x 0'.5) imaging and long-slit spectroscopy. Strategic instruments under development that can utilize the full 23 m baseline of the LBT include an interferometric cryogenic beam combiner with near-infrared and thermal-infrared instruments for Fizeau imaging and nulling interferometry (LBTI) and an optical bench near- infrared beam combiner utilizing multi-conjugate adaptive optics for high angular resolution and sensitivity (LINC-NIRVANA). LBTI is currently undergoing commissioning and performing science observations on the LBT utilizing the installed adaptive secondary mirrors in both single-sided and two-sided beam combination modes. In addition, a fiber-fed bench spectrograph (PEPSI) capable of ultra high resolution spectroscopy and spectropolarimetry (R = 40,000-300,000) will be available as a principal investigator instrument. Installation and testing of the bench spectrograph will begin in July 2014. Over the past four years the LBC pair, LUCI1, and MODS1 have been commissioned and are now scheduled for routine partner science observations. Both LUCI2 and MODS2 passed their laboratory acceptance milestones in the summer of 2013 and have been installed on the LBT. LUCI2 is currently being commissioned and the data analysis is well underway. Diffraction-limited commissioning of its adaptive optics modes will begin in the 2014B semester. MODS2 commissioning began in May 2014 and will completed in the 2014B semester as well. Binocular testing and commissioning of both the LUCI and MODS pairs will begin in 2014B with the goal that this capability could be offered sometime in 2015. The availability of all these instruments mounted simultaneously on the LBT permits unique science, flexible scheduling, and improved operational support.

Effects of D-a-tocopherol and dietary energy on growth and health of preruminant dairy calves

USDA-ARS?s Scientific Manuscript database

To observe the effects of supplemental dietary d-a-tocopherol in relation to dietary energy on growth and immune status in dairy calves, 32 newborn Holstein bull calves were assigned to 1 of 4 treatments for 5 weeks in a 2x2 factorial randomized complete block, split-plot design. Calves received mod...

Lithium wall conditioning by high frequency pellet injection in RFX-mod

NASA Astrophysics Data System (ADS)

Innocente, P.; Mansfield, D. K.; Roquemore, A. L.; Agostini, M.; Barison, S.; Canton, A.; Carraro, L.; Cavazzana, R.; De Masi, G.; Fassina, A.; Fiameni, S.; Grando, L.; Rais, B.; Rossetto, F.; Scarin, P.

2015-08-01

In the RFX-mod reversed field pinch experiment, lithium wall conditioning has been tested with multiple scopes: to improve density control, to reduce impurities and to increase energy and particle confinement time. Large single lithium pellet injection, lithium capillary-pore system and lithium evaporation has been used for lithiumization. The last two methods, which presently provide the best results in tokamak devices, have limited applicability in the RFX-mod device due to the magnetic field characteristics and geometrical constraints. On the other side, the first mentioned technique did not allow injecting large amount of lithium. To improve the deposition, recently in RFX-mod small lithium multi-pellets injection has been tested. In this paper we compare lithium multi-pellets injection to the other techniques. Multi-pellets gave more uniform Li deposition than evaporator, but provided similar effects on plasma parameters, showing that further optimizations are required.

The modA10 phasevarion of nontypeable Haemophilus influenzae R2866 regulates multiple virulence-associated traits.

PubMed

VanWagoner, Timothy M; Atack, John M; Nelson, Kevin L; Smith, Hannah K; Fox, Kate L; Jennings, Michael P; Stull, Terrence L; Smith, Arnold L

2016-03-01

Non-typeable Haemophilus influenzae (NTHi) is a human restricted commensal and pathogen that elicits inflammation by adhering to and invading airway epithelia cells: transcytosis across these cells can result in systemic infection. NTHi strain R2866 was isolated from the blood of a normal 30-month old infant with meningitis, and is unusual for NTHi in that it is able to cause systemic infection. Strain R2866 is able to replicate in normal human serum due to expression of lgtC which mimics human blood group p(k). R2866 contains a phase-variable DNA methyltransferase, modA10 which switches ON and OFF randomly and reversibly due to polymerase slippage over a long tetrameric repeat tract located in its open reading frame. Random gain or loss of repeats during replication can results in expressed (ON), or not expressed (OFF) states, the latter due to a frameshift or transcriptional termination at a premature stop codon. We sought to determine if the unusual virulence of R2866 was modified by modA10 phase-variation. A modA10 knockout mutant was found to have increased adherence to, and invasion of, human ear and airway monolayers in culture, and increased invasion and transcytosis of polarized human bronchial epithelial cells. Intriguingly, the rate of bacteremia was lower in the infant rat model of infection than a wild-type R2866 strain, but the fatality rate was greater. Transcriptional analysis comparing the modA10 knockout to the R2866 wild-type parent strain showed increased expression of genes in the modA10 knockout whose products mediate cellular adherence. We conclude that loss of ModA10 function in strain R2866 enhances colonization and invasion by increasing expression of genes that allow for increased adherence, which can contribute to the increased virulence of this strain. Copyright © 2015 Elsevier Ltd. All rights reserved.

Temperature Regimes Impact Coral Assemblages along Environmental Gradients on Lagoonal Reefs in Belize

PubMed Central

Townsend, Joseph E.; Courtney, Travis A.; Aichelman, Hannah E.; Davies, Sarah W.; Lima, Fernando P.; Castillo, Karl D.

2016-01-01

Coral reefs are increasingly threatened by global and local anthropogenic stressors such as rising seawater temperature, nutrient enrichment, sedimentation, and overfishing. Although many studies have investigated the impacts of local and global stressors on coral reefs, we still do not fully understand how these stressors influence coral community structure, particularly across environmental gradients on a reef system. Here, we investigate coral community composition across three different temperature and productivity regimes along a nearshore-offshore gradient on lagoonal reefs of the Belize Mesoamerican Barrier Reef System (MBRS). A novel metric was developed using ultra-high-resolution satellite-derived estimates of sea surface temperatures (SST) to classify reefs as exposed to low (lowTP), moderate (modTP), or high (highTP) temperature parameters over 10 years (2003 to 2012). Coral species richness, abundance, diversity, density, and percent cover were lower at highTP sites relative to lowTP and modTP sites, but these coral community traits did not differ significantly between lowTP and modTP sites. Analysis of coral life history strategies revealed that highTP sites were dominated by hardy stress-tolerant and fast-growing weedy coral species, while lowTP and modTP sites consisted of competitive, generalist, weedy, and stress-tolerant coral species. Satellite-derived estimates of Chlorophyll-a (chl-a) were obtained for 13-years (2003–2015) as a proxy for primary production. Chl-a concentrations were highest at highTP sites, medial at modTP sites, and lowest at lowTP sites. Notably, thermal parameters correlated better with coral community traits between site types than productivity, suggesting that temperature (specifically number of days above the thermal bleaching threshold) played a greater role in defining coral community structure than productivity on the MBRS. Dominance of weedy and stress-tolerant genera at highTP sites suggests that corals utilizing these two life history strategies may be better suited to cope with warmer oceans and thus may warrant protective status under climate change. PMID:27606598

Temperature Regimes Impact Coral Assemblages along Environmental Gradients on Lagoonal Reefs in Belize.

PubMed

Baumann, Justin H; Townsend, Joseph E; Courtney, Travis A; Aichelman, Hannah E; Davies, Sarah W; Lima, Fernando P; Castillo, Karl D

2016-01-01

Coral reefs are increasingly threatened by global and local anthropogenic stressors such as rising seawater temperature, nutrient enrichment, sedimentation, and overfishing. Although many studies have investigated the impacts of local and global stressors on coral reefs, we still do not fully understand how these stressors influence coral community structure, particularly across environmental gradients on a reef system. Here, we investigate coral community composition across three different temperature and productivity regimes along a nearshore-offshore gradient on lagoonal reefs of the Belize Mesoamerican Barrier Reef System (MBRS). A novel metric was developed using ultra-high-resolution satellite-derived estimates of sea surface temperatures (SST) to classify reefs as exposed to low (lowTP), moderate (modTP), or high (highTP) temperature parameters over 10 years (2003 to 2012). Coral species richness, abundance, diversity, density, and percent cover were lower at highTP sites relative to lowTP and modTP sites, but these coral community traits did not differ significantly between lowTP and modTP sites. Analysis of coral life history strategies revealed that highTP sites were dominated by hardy stress-tolerant and fast-growing weedy coral species, while lowTP and modTP sites consisted of competitive, generalist, weedy, and stress-tolerant coral species. Satellite-derived estimates of Chlorophyll-a (chl-a) were obtained for 13-years (2003-2015) as a proxy for primary production. Chl-a concentrations were highest at highTP sites, medial at modTP sites, and lowest at lowTP sites. Notably, thermal parameters correlated better with coral community traits between site types than productivity, suggesting that temperature (specifically number of days above the thermal bleaching threshold) played a greater role in defining coral community structure than productivity on the MBRS. Dominance of weedy and stress-tolerant genera at highTP sites suggests that corals utilizing these two life history strategies may be better suited to cope with warmer oceans and thus may warrant protective status under climate change.

Change in donor profile influenced the percentage of organs transplanted from multiple organ donors.

PubMed

Meers, C; Van Raemdonck, D; Van Gelder, F; Van Hees, D; Desschans, B; De Roey, J; Vanhaecke, J; Pirenne, J

2009-03-01

We hypothesized that the change in donor profile over the years influenced the percentage of transplantations. We reviewed medical records for all multiple-organ donors (MODs) within our network. The percentage of transplanted organs was compared between 1991-1992 (A) and 2006-2007 (B). In period A, 156 potential MODs were identified compared with 278 in period B. Fifteen potential donors (10%) in period A and 114 (41%) in period B were rejected because they were medically not suitable (40% vs 75%) or there was no family consent (60% vs 25%). Of the remaining effective MODs (141 in period A and 164 in period B), mean (standard deviation = SD) age was 34 (5) years vs 49 (17) years (P < .001). Brain death resulted from craniocerebral trauma in 69% vs 39%, cerebrovascular disease in 24% vs 46%, hypoxia in 4% vs 15%, and brain tumor in 2% vs 0.6% (P < .001). Chest trauma was present in 19% vs 9% (P < .01). The percentage of MODs who received mechanical ventilation for more than 5 days was 8% vs 24% (P < .001). The percentage of organs transplanted in periods A vs B was kidneys, 97% vs 79%; livers, 64% vs 85%; hearts, 60% vs 26%; lungs, 7% vs 35%; and pancreas, 6% vs 13% (P < .001). The number of referred potential MODs increased by 80%, resulting in a small increase in effective MOD organs (17%), mainly because of medical contraindications. The MOD profile changed to older age, fewer traumatic brain deaths, and longer ventilation time. We transplanted more livers, lungs, and pancreases but fewer kidneys and hearts.

Final results from a defibrotide treatment-IND study for patients with hepatic veno-occlusive disease/sinusoidal obstruction syndrome.

PubMed

Kernan, Nancy A; Grupp, Stephan; Smith, Angela R; Arai, Sally; Triplett, Brandon; Antin, Joseph H; Lehmann, Leslie; Shore, Tsiporah; Ho, Vincent T; Bunin, Nancy; Iacobelli, Massimo; Liang, Wei; Hume, Robin; Tappe, William; Soiffer, Robert; Richardson, Paul

2018-05-16

Hepatic veno-occlusive disease/sinusoidal obstruction syndrome (VOD/SOS) is a potentially life-threatening complication of haematopoietic stem cell transplant (HSCT) conditioning and chemotherapy. Defibrotide is approved for treatment of hepatic VOD/SOS with pulmonary or renal dysfunction [i.e., multi-organ dysfunction (MOD)] after HSCT in the United States and severe VOD/SOS after HSCT in patients aged older than 1 month in the European Union. Defibrotide was available as an investigational drug by an expanded-access treatment programme (T-IND; NCT00628498). In the completed T-IND, the Kaplan-Meier estimated Day +100 survival for 1000 patients with documented defibrotide treatment after HSCT was 58·9% [95% confidence interval (CI), 55·7-61·9%]. Day +100 survival was also analysed by age and MOD status, and post hoc analyses were performed to determine Day +100 survival by transplant type, timing of VOD/SOS onset (≤21 or >21 days) and timing of defibrotide treatment initiation after VOD/SOS diagnosis. Day +100 survival in paediatric patients was 67·9% (95% CI, 63·8-71·6%) and 47·1% (95% CI, 42·3-51·8%) in adults. All patient subgroups without MOD had higher Day +100 survival than those with MOD; earlier defibrotide initiation was also associated with higher Day +100 survival. The safety profile of defibrotide in the completed T-IND study was similar to previous reports. © 2018 The Authors. British Journal of Haematology published by John Wiley & Sons Ltd.

Energetic ion loss detector on the Alcator C-Mod tokamak.

PubMed

Pace, D C; Granetz, R S; Vieira, R; Bader, A; Bosco, J; Darrow, D S; Fiore, C; Irby, J; Parker, R R; Parkin, W; Reinke, M L; Terry, J L; Wolfe, S M; Wukitch, S J; Zweben, S J

2012-07-01

A scintillator-based energetic ion loss detector has been successfully commissioned on the Alcator C-Mod tokamak. This probe is located just below the outer midplane, where it captures ions of energies up to 2 MeV resulting from ion cyclotron resonance heating. After passing through a collimating aperture, ions impact different regions of the scintillator according to their gyroradius (energy) and pitch angle. The probe geometry and installation location are determined based on modeling of expected lost ions. The resulting probe is compact and resembles a standard plasma facing tile. Four separate fiber optic cables view different regions of the scintillator to provide phase space resolution. Evolving loss levels are measured during ion cyclotron resonance heating, including variation dependent upon individual antennae.

Sur la modélisation des supraconducteurs : le ``modèle de l'état critique'' de Bean, en trois dimensions

NASA Astrophysics Data System (ADS)

Bossavit, A.

1993-03-01

Macroscopic modelling of superconductors demands a substitution of some nonlinear behavior law for Ohm's law. For this, a version of Bean's “critical state” model, derived from the setting of a convex functional of the current density field, valid in dimension 3 without any previous assumption about the direction of currents, is proposed. It is shown how two standard three-dimensional finite element methods (“h-formulation” and “e-formulation”), once fitted with this model, can deal with situations were superconductors are present. La modélisation macroscopique des supraconducteurs suppose le remplacement de la loi d'Ohm par une loi de comportement non linéaire adéquate. On présente à cet effet une version du “modèle de Bean”, ou modèle de l'état critique, basée sur la construction d'une certaine fonctionnelle convexe du champ des densités de courant, qui est valable en dimension 3 sans hypothèses préalables sur la direction des courants. On montre comment adapter deux méthodes standards de calcul de courants de Foucault par élérnents finis en trois dimensions (“en h” et “en e”) à la présence de supraconducteurs, en incorporant ce modèle.

Calculation of design load for the MOD-5A 7.3 mW wind turbine system

NASA Technical Reports Server (NTRS)

Mirandy, L.; Strain, J. C.

1995-01-01

Design loads are presented for the General Electric MOD-SA wind turbine. The MOD-SA system consists of a 400 ft. diameter, upwind, two-bladed, teetered rotor connected to a 7.3 mW variable-speed generator. Fatigue loads are specified in the form of histograms for the 30 year life of the machine, while limit (or maximum) loads have been derived from transient dynamic analysis at critical operating conditions. Loads prediction was accomplished using state of the art aeroelastic analyses developed at General Electric. Features of the primary predictive tool - the Transient Rotor Analysis Code (TRAC) are described in the paper. Key to the load predictions are the following wind models: (1) yearly mean wind distribution; (2) mean wind variations during operation; (3) number of start/shutdown cycles; (4) spatially large gusts; and (5) spatially small gusts (local turbulence). The methods used to develop statistical distributions from load calculations represent an extension of procedures used in past wind programs and are believed to be a significant contribution to Wind Turbine Generator analysis. Test/theory correlations are presented to demonstrate code load predictive capability and to support the wind models used in the analysis. In addition MOD-5A loads are compared with those of existing machines. The MOD-5A design was performed by the General Electric Company, Advanced Energy Program Department, under Contract DEN3-153 with NASA Lewis Research Center and sponsored by the Department of Energy.

Analysis Of The Land Surface Temperature And NDVI Using MODIS Data On The Arctic Tundra During The Last Decade

NASA Astrophysics Data System (ADS)

Mattar, C.; Duran-Alarcon, C.; Jimenez-Munoz, J. C.; Sobrino, J. A.

2013-12-01

The arctic tundra is one of the most sensible biome to climate conditions which has experienced important changes in the spatial distribution of temperature and vegetation in the last decades. In this paper we analyzed the spatio-temporal trend of the Land Surface Temperature (LST) and the Normalized Difference Vegetation Index (NDVI) over the arctic tundra biome during the last decade (2001-2012) derived from Moderate Resolution Imaging Spectroradiometer (MODIS) land products MOD11C3 (LST) and MOD13C2 (NDVI) were used. Anomalies for each variable were analyzed at monthly level, and the magnitude and statistical significance of the trends were computed using the non-parametric tests of Sen's Slope and Mann-Kendal respectively. The results obtained from MODIS LST data showed a significant increase (p-value < 0.05) on surface temperature over the arctic tundra in the last decade. In the case of the NDVI, the trend was positive (increase on NDVI) but statistically not significant (p-value < 0.05). All tundra regions defined in the Circumpolar Arctic Vegetation Map have presented positive and statistically significant trends in NDVI and LST. Values of trends obtained from MODIS data over all the tundra regions were +1.10 [°C/dec] in the case of LST and +0.005 [NDVI value/dec] in the case of NDVI.

NetMOD Version 2.0 Mathematical Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.; Young, Christopher J.; Chael, Eric P.

2015-08-01

NetMOD ( Net work M onitoring for O ptimal D etection) is a Java-based software package for conducting simulation of seismic, hydroacoustic and infrasonic networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes of signal and noise that are observed at each ofmore » the stations. From these signal-to-noise ratios (SNR), the probabilities of signal detection at each station and event detection across the network of stations can be computed given a detection threshold. The purpose of this document is to clearly and comprehensively present the mathematical framework used by NetMOD, the software package developed by Sandia National Laboratories to assess the monitoring capability of ground-based sensor networks. Many of the NetMOD equations used for simulations are inherited from the NetSim network capability assessment package developed in the late 1980s by SAIC (Sereno et al., 1990).« less

Posttest data analysis of FIST experimental TRAC-BD1/MOD1 power transient experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wheatley, P.D.; Wagner, K.C.

The FIST power transient test 6PMC2 was analyzed to further the understanding of the FIST facility and provide an assessment of TRAC-BD1/MOD1. FIST power transient 6PMC2 investigated the thermal-hydraulic response following inadvertent closure of the main steam isolation valve and the subsequent failure of the reactor to scram. Failure of the high pressure core spray system was also assumed, resulting in only the reactor core isolation cooling flow for inventory makeup during the transient. The experiment was a sensitivity study with relatively high core power and low makeup rates. This study provides one of the first opportunities to assess TRAC-BD1/MOD1more » under power transient and natural circulation conditions with data from a facility with prototypical BWR geometry. The power transient test was analyzed with emphasis on the following phenomena: (a) the system pressure response, (b) the natural circulation flows and rates, and (c) the heater rod cladding temperature response. Based on the results of this study, TRAC-BD1/MOD1 can be expected to calculate the thermal-hydraulic behavior of a BWR during a power transient.« less

Mod-5A Wind Turbine Generator Program Design Report. Volume 2: Conceptual and Preliminary Design, Book 1

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. There are four volumes. In Volume 2, book 1 the requirements and criteria for the design are presented. The conceptual design studies, which defined a baseline configuration and determined the weights, costs and sizes of each subsystem, are described. The development and optimization of the wind turbine generator are presented through the description of the ten intermediate configurations between the conceptual and final designs. Analyses of the system's load and dynamics are presented.

Signatures of inflammation and impending multiple organ dysfunction in the hyperacute phase of trauma: A prospective cohort study

PubMed Central

Longhi, M. Paula; Hoti, Mimoza; Patel, Minal B.; O’Dwyer, Michael; Nourshargh, Sussan; Barnes, Michael R.; Brohi, Karim

2017-01-01

Background Severe trauma induces a widespread response of the immune system. This “genomic storm” can lead to poor outcomes, including Multiple Organ Dysfunction Syndrome (MODS). MODS carries a high mortality and morbidity rate and adversely affects long-term health outcomes. Contemporary management of MODS is entirely supportive, and no specific therapeutics have been shown to be effective in reducing incidence or severity. The pathogenesis of MODS remains unclear, and several models are proposed, such as excessive inflammation, a second-hit insult, or an imbalance between pro- and anti-inflammatory pathways. We postulated that the hyperacute window after trauma may hold the key to understanding how the genomic storm is initiated and may lead to a new understanding of the pathogenesis of MODS. Methods and findings We performed whole blood transcriptome and flow cytometry analyses on a total of 70 critically injured patients (Injury Severity Score [ISS] ≥ 25) at The Royal London Hospital in the hyperacute time period within 2 hours of injury. We compared transcriptome findings in 36 critically injured patients with those of 6 patients with minor injuries (ISS ≤ 4). We then performed flow cytometry analyses in 34 critically injured patients and compared findings with those of 9 healthy volunteers. Immediately after injury, only 1,239 gene transcripts (4%) were differentially expressed in critically injured patients. By 24 hours after injury, 6,294 transcripts (21%) were differentially expressed compared to the hyperacute window. Only 202 (16%) genes differentially expressed in the hyperacute window were still expressed in the same direction at 24 hours postinjury. Pathway analysis showed principally up-regulation of pattern recognition and innate inflammatory pathways, with down-regulation of adaptive responses. Immune deconvolution, flow cytometry, and modular analysis suggested a central role for neutrophils and Natural Killer (NK) cells, with underexpression of T- and B cell responses. In the transcriptome cohort, 20 critically injured patients later developed MODS. Compared with the 16 patients who did not develop MODS (NoMODS), maximal differential expression was seen within the hyperacute window. In MODS versus NoMODS, 363 genes were differentially expressed on admission, compared to only 33 at 24 hours postinjury. MODS transcripts differentially expressed in the hyperacute window showed enrichment among diseases and biological functions associated with cell survival and organismal death rather than inflammatory pathways. There was differential up-regulation of NK cell signalling pathways and markers in patients who would later develop MODS, with down-regulation of neutrophil deconvolution markers. This study is limited by its sample size, precluding more detailed analyses of drivers of the hyperacute response and different MODS phenotypes, and requires validation in other critically injured cohorts. Conclusions In this study, we showed how the hyperacute postinjury time window contained a focused, specific signature of the response to critical injury that led to widespread genomic activation. A transcriptomic signature for later development of MODS was present in this hyperacute window; it showed a strong signal for cell death and survival pathways and implicated NK cells and neutrophil populations in this differential response. PMID:28715416

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

Disruption Neutral Point Experiment on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Granetz, R. S.; Nakamura, Y.

2000-10-01

Disruptions of single-null elongated plasmas generally result in loss of vertical position control, leading to a current quench occurring at the top or bottom of the machine, with all the attendant problems of halo and eddy currents flowing in divertor structures. On JT-60U, it has been found that if the plasma is operated with its magnetic axis at a particular height, called the neutral point, the initial vertical drift after a thermal quench is significantly slower than usual, and sometimes can even be arrested, thereby avoiding a current quench in the divertor region entirely. In an ongoing collaboration between MIT and JAERI, the neutral point concept is being tested in Alcator C-Mod, which has a significantly higher plasma elongation than JT-60U (1.65 vs 1.3). Calculations using TSC predict a neutral point at z~=+1 cm above the midplane (a=22 cm). The existence of a neutral point has now been experimentally confirmed, albeit at a height of z=+2.7 cm. The plasma has remained vertically stable for up to 9 ms after the disruption thermal quench, which in principle, is long enough for the PF control system to respond, if programmed appropriately. In addition, the physics of the neutral point stability on C-Mod appears to be somewhat different than that on JT-60U.

Demonstrating the Physics Basis for the ITER 15 MA Inductive Discharge on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Kessel, C. E.; Wolfe, S. M.; Hutchinson, I. H.; Hughes, J. W.; Lin, Y.; Ma, Y.; Mikkelsen, D. R.; Poli, F.; Reinke, M. L.; Wukitch, S. J.

2012-10-01

Rampup discharges in C-Mod, matching ITE's current diffusion times show ICRF heating can save V-s but results in only weak effects on the current profile, despite strong modifications of the central electron temperature. Simulation of these discharges with TSC, and TORIC for ICRF, using multiple transport models, do not reproduce the temperature profile evolution, or the experimental internal self-inductance li, by sufficiently large amounts to be unacceptable for projections to ITER operation. For the flattop phase experiments EDA H-modes approach the ITER parameter targets of q95=3, H98=1, n/nGr=0.85, betaN=1.7, and k=1.8, and sustain them similar to a normalized ITER flattop time. The discharges show a degradation of energy confinement at higher densities, but increasing H98 with increasing net power to the plasma. For these discharges intrinsic impurities (B, Mo) provided radiated power fractions of 25-37%. Experiments show the plasma can remain in H-mode in rampdown with ICRF injection, the density will decrease with Ip while in the H-mode, and the back transition occurs when the net power reaches about half the L-H transition power. C-Mod indicates that faster rampdowns are preferable. Work supported by US Dept of Energy under DE-AC02-CH0911466 and DE-FC02-99ER54512.

High Performance Regimes in Alcator C-Mod at High Magnetic Field

NASA Astrophysics Data System (ADS)

Marmar, E. S.; Alcator C-Mod Team

2017-10-01

Alcator is the only divertor tokamak in the world capable of operating at magnetic fields up to 8 T, equaling and exceeding that planned for ITER. Using RF and microwave tools for auxiliary heating and current drive, C-Mod accesses high pressure, high density, reactor-relevant regimes with no external torque and equilibrated electrons and ions, with exclusive use of high-Z metal plasma-facing components. The 2016 experimental campaign focused on naturally ELM-suppressed, enhanced energy confinement regimes (including I-mode and EDA H-mode, and approaches to super-H-mode), with emphasis on operation at the highest fields (52 atm.) was achieved. Taken together, combined with previous results from C-Mod and the world tokamak database, these results form a strong foundation for the high field, compact approach to achieving fusion energy production. New advances in high temperature, high field superconductors open the possibilities for practical development of this path for commercial fusion. Supported by USDOE.

Mod-5A wind turbine generator program design report. Volume 2: Conceptual and preliminary design, book 2

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind tunnel generator is documented. There are four volumes. In Volume 2, book 2 the requirements and criteria for the design are presented. The development tests, which determined or characterized many of the materials and components of the wind turbine generator, are described.

MOD-1 Wind Turbine Generator Analysis and Design Report, Volume 2

NASA Technical Reports Server (NTRS)

1979-01-01

The MOD-1 detail design is appended. The supporting analyses presented include a parametric system trade study, a verification of the computer codes used for rotor loads analysis, a metal blade study, and a definition of the design loads at each principal wind turbine generator interface for critical loading conditions. Shipping and assembly requirements, composite blade development, and electrical stability are also discussed.

R-HyMOD: an R-package for the hydrological model HyMOD

NASA Astrophysics Data System (ADS)

Baratti, Emanuele; Montanari, Alberto

2015-04-01

A software code for the implementation of the HyMOD hydrological model [1] is presented. HyMOD is a conceptual lumped rainfall-runoff model that is based on the probability-distributed soil storage capacity principle introduced by R. J. Moore 1985 [2]. The general idea behind this model is to describe the spatial variability of some process parameters as, for instance, the soil structure or the water storage capacities, through probability distribution functions. In HyMOD, the rainfall-runoff process is represented through a nonlinear tank connected with three identical linear tanks in parallel representing the surface flow and a slow-flow tank representing groundwater flow. The model requires the optimization of five parameters: Cmax (the maximum storage capacity within the watershed), β (the degree of spatial variability of the soil moisture capacity within the watershed), α (a factor for partitioning the flow between two series of tanks) and the two residence time parameters of quick-flow and slow-flow tanks, kquick and kslow respectively. Given its relatively simplicity but robustness, the model is widely used in the literature. The input data consist of precipitation and potential evapotranspiration at the given time scale. The R-HyMOD package is composed by a 'canonical' R-function of HyMOD and a fast FORTRAN implementation. The first one can be easily modified and can be used, for instance, for educational purposes; the second part combines the R user friendly interface with a fast processing unit. [1] Boyle D.P. (2000), Multicriteria calibration of hydrological models, Ph.D. dissertation, Dep. of Hydrol. and Water Resour., Univ of Arizona, Tucson. [2] Moore, R.J., (1985), The probability-distributed principle and runoff production at point and basin scale, Hydrol. Sci. J., 30(2), 273-297.

Intermittent electron density and temperature fluctuations and associated fluxes in the Alcator C-Mod scrape-off layer

NASA Astrophysics Data System (ADS)

Kube, R.; Garcia, O. E.; Theodorsen, A.; Brunner, D.; Kuang, A. Q.; LaBombard, B.; Terry, J. L.

2018-06-01

The Alcator C-Mod mirror Langmuir probe system has been used to sample data time series of fluctuating plasma parameters in the outboard mid-plane far scrape-off layer. We present a statistical analysis of one second long time series of electron density, temperature, radial electric drift velocity and the corresponding particle and electron heat fluxes. These are sampled during stationary plasma conditions in an ohmically heated, lower single null diverted discharge. The electron density and temperature are strongly correlated and feature fluctuation statistics similar to the ion saturation current. Both electron density and temperature time series are dominated by intermittent, large-amplitude burst with an exponential distribution of both burst amplitudes and waiting times between them. The characteristic time scale of the large-amplitude bursts is approximately 15 μ {{s}}. Large-amplitude velocity fluctuations feature a slightly faster characteristic time scale and appear at a faster rate than electron density and temperature fluctuations. Describing these time series as a superposition of uncorrelated exponential pulses, we find that probability distribution functions, power spectral densities as well as auto-correlation functions of the data time series agree well with predictions from the stochastic model. The electron particle and heat fluxes present large-amplitude fluctuations. For this low-density plasma, the radial electron heat flux is dominated by convection, that is, correlations of fluctuations in the electron density and radial velocity. Hot and dense blobs contribute only a minute fraction of the total fluctuation driven heat flux.

Prediction of global and local model quality in CASP8 using the ModFOLD server.

PubMed

McGuffin, Liam J

2009-01-01

The development of effective methods for predicting the quality of three-dimensional (3D) models is fundamentally important for the success of tertiary structure (TS) prediction strategies. Since CASP7, the Quality Assessment (QA) category has existed to gauge the ability of various model quality assessment programs (MQAPs) at predicting the relative quality of individual 3D models. For the CASP8 experiment, automated predictions were submitted in the QA category using two methods from the ModFOLD server-ModFOLD version 1.1 and ModFOLDclust. ModFOLD version 1.1 is a single-model machine learning based method, which was used for automated predictions of global model quality (QMODE1). ModFOLDclust is a simple clustering based method, which was used for automated predictions of both global and local quality (QMODE2). In addition, manual predictions of model quality were made using ModFOLD version 2.0--an experimental method that combines the scores from ModFOLDclust and ModFOLD v1.1. Predictions from the ModFOLDclust method were the most successful of the three in terms of the global model quality, whilst the ModFOLD v1.1 method was comparable in performance to other single-model based methods. In addition, the ModFOLDclust method performed well at predicting the per-residue, or local, model quality scores. Predictions of the per-residue errors in our own 3D models, selected using the ModFOLD v2.0 method, were also the most accurate compared with those from other methods. All of the MQAPs described are publicly accessible via the ModFOLD server at: http://www.reading.ac.uk/bioinf/ModFOLD/. The methods are also freely available to download from: http://www.reading.ac.uk/bioinf/downloads/. Copyright 2009 Wiley-Liss, Inc.

Optimizing LHCD launcher using poloidal steering on Alcator C-Mod and ADX

NASA Astrophysics Data System (ADS)

Bonoli, P.; Labombard, B.; Parker, R.; Shiraiwa, S.; Wallace, G.; Wukitch, S.; Leccacorvi, R.; Vieira, R.; Alcator C-Mod Team

2014-10-01

The poloidal location of the lower hybrid current drive (LHCD) launcher has a strong influence on the trajectory and absorption of the LH wave (poloidal steering). The physics design of an additional off-midplane launcher (LH3) for Alcator C-Mod exploits this characteristic. By shifting the launcher from the mid-plane by 25cm, it is predicted to realize strong (>80%) single pass absorption localized at about r/a = 0.7 in conjunction with the mid-plane (LH2) antenna. While LH3 is a proposal to overcome the LH density limit and to provide a unique opportunity to validate LHCD simulation codes under reactor-like conditions, poloidal steering can be used more extensively by launching waves from the high field side (HFS). On ADX, the LHCD launcher is proposed to be located on the HFS. Better accessibility due to higher magnetic field allows for using lower N//, which results in higher current drive efficiency. Also a more quiescent edge plasma may reduce the effect of N// shifts due to scattering from density fluctuations. LHCD simulations for target plasmas expected on ADX, optimization of poloidal steering, and RF simulation of high field side launcher will be presented. This work supported by USDoE awards DE-FC02-99ER54512 and DE-AC02-09CH11466.

Reduction of ion transport and turbulence via dilution with nitrogen and neon injection in C-Mod deuterium plasmas

NASA Astrophysics Data System (ADS)

Porkolab, M.; Ennever, P.; Baek, S. G.; Creely, A. J.; Edlund, E. M.; Hughes, J.; Rice, J. E.; Rost, J. C.; White, A. E.; Reinke, M. L.; Staebler, G.; Candy, J.; Alcator C-Mod Team

2016-10-01

Recent experiments on C-Mod ohmic plasmas and gyrokinetic studies indicated that dilution of deuterium plasmas by injection of nitrogen decreased the ion diffusivity and may also alter the direction of intrinsic toroidal rotation. Simulations with TGLF and GYRO showed that dilution of deuterium ions in low density (LOC) plasmas increased the critical ion temperature gradient, while in high density (SOC) plasmas it decreased the stiffness. The density fluctuation spectrum measured in low q95 plasmas with Phase Contrast Imaging (PCI), and corroborated with spatially localized reflectometer measurements show a reduction of turbulence near r/a = 0.8 with kρs <= 1, in agreement with modeling predictions in this region where the ion turbulence is well above marginal stability. Measurements also indicate that reversal of the toroidal rotation direction near the SOC-LOC transition may depend on ion collisionality rather than that of electrons. New experiments with neon seeding, which may be more relevant to ITER than with nitrogen seeding, show similar results. The impact of dilution on Te turbulence as measured with CECE diagnostic will also be presented. Supported by US DOE Awards DE-FG02-94-ER54235 and DE-FC02-99-ER54512.

Spanish Earth Observation Satellite System

NASA Astrophysics Data System (ADS)

Borges, A.; Cerezo, F.; Fernandez, M.; Lomba, J.; Lopez, M.; Moreno, J.; Neira, A.; Quintana, C.; Torres, J.; Trigo, R.; Urena, J.; Vega, E.; Vez, E.

2010-12-01

The Spanish Ministry of Industry, Tourism and Trade (MITyC) and the Ministry of Defense (MoD) signed an agreement in 2007 for the development of a "Spanish Earth Observation Satellite System" based, in first instance, on two satellites: a high resolution optical satellite, called SEOSAT/Ingenio, and a radar satellite based on SAR technology, called SEOSAR/Paz. SEOSAT/Ingenio is managed by MITyC through the Centre for the Development of Industrial Technology (CDTI), with technical and contractual support from the European Space Agency (ESA). HISDESA T together with the Spanish Instituto Nacional de Técnica Aeroespacial (INTA, National Institute for Aerospace Technology) will be responsible for the in-orbit operation and the commercial operation of both satellites, and for the technical management of SEOSAR/Paz on behalf of the MoD. In both cases EADS CASA Espacio (ECE) is the prime contractor leading the industrial consortia. The ground segment development will be assigned to a Spanish consortium. This system is the most important contribution of Spain to the European Programme Global Monitoring for Environment and Security, GMES. This paper presents the Spanish Earth Observation Satellite System focusing on SEOSA T/Ingenio Programme and with special emphasis in the potential contribution to the ESA Third Party Missions Programme and to the Global Monitoring for Environment and Security initiative (GMES) Data Access.

Initial cytotoxicity assays of media for sulfate-reducing bacteria: An endodontic biopharmaceutical product under development.

PubMed

Heggendorn, Fabiano Luiz; Silva, Gabriela Cristina de Carvalho; Cardoso, Elisama Azevedo; Castro, Helena Carla; Gonçalves, Lúcio Souza; Dias, Eliane Pedra; Lione, Viviane de Oliveira Freitas; Lutterbach, Márcia Teresa Soares

2016-01-01

This study assessed the cell viability of the inoculation vehicle of BACCOR (a combination of sulfate-reducing bacteria plus a culture media for bacteria), a biopharmaceutical product under development for dental use as aid in fractured endodontic file removal from the root canal. Different culture media for bacteria were evaluated: modified Postgate E (MCP-E mod), Modified Postgate E without Agar-agar (MCP-E w/Ag), Postgate C with Agar-agar (MCP-C Ag) and Postgate C without Agar-agar (MCP-C w/Ag). Cytotoxicity was quantified by the MTT test, exposing L929 and Vero cell lines to the vehicles over 24 h. The exposure of L929 cell line to MCP-E w/Ag resulted in biocompatibility (52% cell viability), while the exposure of the Vero kidney line revealed only MCP-E mod as cytotoxic. When diluted, all the vehicles showed biocompatibility with both cell lines. MCP-E w/Ag was the vehicle chosen for BACCOR, because of its biocompatibility with the cells used.

In-situ wavelength calibration and temperature control for the C-Mod high-resolution x-ray crystal imaging spectrometer

NASA Astrophysics Data System (ADS)

Delgado-Aparicio, Luis F.; Podpaly, Y.; Reinke, M. L.; Gao, C.; Rice, J.; Scott, S.; Bitter, M.; Hill, K.; Beiersdorfer, P.; Johnson, D.; Wilson, J. R.

2010-11-01

An x-ray crystal imaging spectrometer with high spectral and spatial resolution is currently being used on Alcator C-Mod to infer time histories of temperature and velocity profiles. An in-situ wavelength calibration using a 1 μm palladium filter in between the crystal and the detectors of choice is being proposed as a natural wavelength-marker using the transmission changes across the L-II and L-III edges at 3722.9 mA and 3907.1 mA, respectively. Recent results also indicate that the crystal temperature should be kept constant within a fraction of a degree since the thermal expansion of the quartz crystal will change the interplanar (2d) spacing and introduce fictitious velocity measurements of several km/s. A detailed temperature scan indicates a thermal expansion coefficient (α) of 13.5x10-6 /^oC and thus a false Doppler shift of 4.05.δT[^oC] km/s.

Assessment of TRAC-PF1/MOD1 version 14. 3 using separate effects critical flow and blowdown experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spindler, B.; Pellissier, M.

1990-01-01

Independent assessment of the TRAC code was conducted at the Centre d'Etudes Nucleaires de Grenoble of the Commissariate a l'Energie Atomique (France) in the frame of the ICAP. This report presents the results of the assessment of TRAC-PF1/MOD1 version 14.3 using critical flow steady state tests (MOBY-DICK, SUPER-MOBY-DICK), and blowdown tests (CANON, SUPER-CANON, VERTICAL-CANON, MARVIKEN, OMEGA-TUBE, OMEGA-BUNDLE). This document, Volume 1, presents the text and tables from this assessment.

Assessment of TRAC-PF1/MOD1 Version 14. 3 using separate effects critical flow and blowdown experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spindler, B.; Pellissier, M.

1990-01-01

Independent assessment of the TRAC code was conducted at the Centre d'Etudes Nucleaires de Grenoble of the Commissariate a l'Energie Atomique (France) in the frame of the ICAP. This report presents the results of the assessment of TRAC-PF1/MOD1 version 14.3 using critical flow steady state tests (MOBY-DICK, SUPER-MOBY-DICK), and blowdown tests (CANON, SUPER-CANON, VERTICAL-CANON, MARVIKEN, OMEGA-TUBE, OMEGA-BUNDLE). This document, Volume 2, presents the experimental data and figures from the assessment.

Removal of phosphate from eutrophic lakes through adsorption by in situ formation of magnesium hydroxide from diatomite.

PubMed

Xie, Fazhi; Wu, Fengchang; Liu, Guijian; Mu, Yunsong; Feng, Chenglian; Wang, Huanhua; Giesy, John P

2014-01-01

Since in situ formation of Mg(OH)2 can efficiently sorb phosphate (PO4) from low concentrations in the environment, a novel dispersed magnesium oxide nanoflake-modified diatomite adsorbent (MOD) was developed for use in restoration of eutrophic lakes by removal of excess PO4. Various adsorption conditions, such as pH, temperature and contact time were investigated. Overall, sorption capacities increased with increasing temperature and contact time, and decreased with increasing pH. Adsorption of PO4 was well described by both the Langmuir isotherm and pseudo second-order models. Theoretical maximum sorption capacity of MOD for PO4 was 44.44-52.08 mg/g at experimental conditions. Characterization of PO4 adsorbed to MOD by use of X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and solid state (31)P nuclear magnetic resonance revealed that electrostatic attraction, surface complexation and chemical conversion in situ were the major forces in adsorption of PO4. Mg(OH)2 formed in situ had a net positive charge on the surface of the MOD that could adsorb PO4(3-) and HPO4(2-) anion to form surface complex and gradually convert to Mg3(PO4)2 and MgHPO4. Efficiency of removal of PO4 was 90% when 300 mg MOD/L was added to eutrophic lake water. Results presented here demonstrated the potential use of the MOD for restoration of eutrophic lakes by removal of excess PO4.

Measurements of Mode Converted Ion Cyclotron Wave with Phase Contrast Imaging in Alcator C-Mod and Comparisons with Synthetic PCI Simulations in TORIC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsujii, N.; Porkolab, M.; Edlund, E. M.

2009-11-26

Mode converted ion cyclotron wave (ICW) has been observed with phase contrast imaging (PCI) in D-{sup 3}He plasmas in Alcator C-Mod. The measurements were carried out with the optical heterodyne technique using acousto-optic modulators which modulate the CO2 laser beam intensity near the ion cyclotron frequency. With recently improved calibration of the PCI system using a calibrated sound wave source, the measurements have been compared with the full-wave code TORIC, as interpreted by a synthetic diagnostic. Because of the line-integrated nature of the PCI signal, the predictions are sensitive to the exact wave field pattern. The simulations are found tomore » be in qualitative agreement with the measurements.« less

3-D Synthetic Microstructure Generation with Ellipsoid Particles

DTIC Science & Technology

2016-09-27

MATLAB scripts in Appendix A, Appendix B, and Appendix C by using 3 -D matrices, where the background is 0 and the particle is 1. For the 3 -D ellipses, it...iy(iy== 0 )=image_size(2); nlo = z0 - floor(diam/2); nhi = z0 + ceil(diam/2)-1; iz = mod(nlo:nhi,image_size( 3 ));iz(iz== 0 )=image_size( 3 ); Itest = logical...z0 + ceil(diam/2)-1; iz = mod(nlo:nhi,image_size( 3 )); iz(iz== 0 )=image_size( 3 ); Itest = logical(I(ix,iy,iz)); if sum(Itest(I_ellipse)) == 0 Itest

Soldiers in Cold Environments (Soldats en environnements froids)

DTIC Science & Technology

2009-04-01

survie par temps froid et en eau froide pour l’essai de divers ensembles d’habillement ; d) envisager l’adoption du procédé d’Ulm pour le traitement des...vêtements d’hiver ; • Les expériences de laboratoire en air froid et sur la morsure du gel; • La modélisation de la survie en eau froide et en air froid...normalisés au sein des pays de l’OTAN ; b) développer un protocole commun pour le traitement de l’hypothermie; c) développer un modèle de prévision de

Biomass burning and its relationship with water cycle dynamics of the Chari-Logone catchment of Lake Chad Basin

NASA Astrophysics Data System (ADS)

Black, F. W.; Lee, J.; Ellison, L.; Gupta, M.; Bolten, J. D.; Gatebe, C. K.; Ichoku, C. M.

2016-12-01

The cause of shrinkage of Lake Chad has been of great interest for issues of global warming and climate change. The present study investigates the effect of biomass burning on the water cycle dynamics of Lake Chad Basin in the Northern Sub-Saharan Africa. Burning activities increase from November to April when monsoonal precipitation is at its lowest and decreases dramatically from May to October when precipitation peaks. To circumvent weather station scarcity in the region, a variety of satellite products were used as input into a water balance model. The datasets include TRMM 3B31 for precipitation, SRTM for elevation, and MODIS: MOD11C3 for temperature, MOD12Q1 for land cover, and MOD14A for fire count. Non-satellite based data sources include soil maps from the Harmonized World Soil Database and wind speed from NOAA NCDC stations. The Chari-Logone catchment of the Lake Chad Basin was selected since it supplies over 90% of the water input to the Lake. Fire count data from MOD14A were integrated with land cover albedo changes to determine monthly potential evapotranspiration (PET) using a Penman equation. The resolution of the model is 2 km x 2 km which allows for delineation of physical features such as lakes and other water bodies. Fire counts, also at a resolution of 2 km x 2 km, vary dramatically depending on the season. A separate land cover dataset was created to account for the effect of burning of different vegetative land types, which affects vegetative area, bare area, leaf area index, vegetation height, Manning coefficient, and aerodynamic resistance. Two water balance simulations, one considering burning and one without, were compared from the years 2005 to 2010. Results indicate biomass burning contribute to an increase in average monthly runoff and a decrease in groundwater recharge. Actual evapotranspiration shows variation depending on the month.

Atom-replaced pins in a Y-based superconductor—single-crystalline perovskite structure including both PrBa2Cu3O7‑x and YBa2Cu3O7‑y

NASA Astrophysics Data System (ADS)

Hayashi, Mariko; Araki, Takeshi; Ishii, Hirotaka; Nishijima, Gen; Matsumoto, Akiyoshi

2018-05-01

Metal organic deposition using trifluoroacetates (TFA-MOD) provides many uniform superconductors on long metal tapes. The large numbers of long wires have been applied for power grids or superconducting fault current limiters. The related applications worked for a long time without fatal trouble. The quasi-liquid produced during the firing process assisted the perfectly uniform structure in TFA-MOD. On the other hand, when it was desired to introduce artificial pinning centers, the quasi-liquid also enlarged the diameter of the artificial pinning centers to several tens of nanometers. In other words, due to the nature of TFA-MOD, there is very little chance of using TFA-MOD to prepare several nm-sized artificial pinning centers. By proposing atom-replaced pins (ARPs), we aim to overcome the impasse. ARPs are realized by replacing yttrium (Y) with praseodymium (Pr) whose valence number changes from 3+ to approximately 4+. Analytical results suggested that Pr makes pinning centers on a PrBa2Cu3O7‑x (PrBCO) unit cell, and the weak-linked superconductivity derived from PrBCO extends to the adjacent unit cells in the a/b-plane. J c decrease by Pr is five times as large as the volume fraction of Pr in the Y-site of the perovskite structure. On the other hand, T c does not show large degradation in YBCO including 10% PrBCO. These results suggest that PrBCO unit cells are fully dispersed in YBa2Cu3O7‑y matrix. With regard to J c in the magnetic field, (Y0.98, Pr0.02)BCO has been slightly improved compared with pure YBCO only in the region of high temperature and low magnetic field of less than 1 T.

Improvement of satellite-based gross primary production through incorporation of high resolution input data over east asia

NASA Astrophysics Data System (ADS)

Park, Haemi; Im, Jungho; Kim, Miae

2016-04-01

Photosynthesis of plants is the main mechanism of carbon absorption from the atmosphere into the terrestrial ecosystem and it contributes to remove greenhouse gases such as carbon dioxide. Annually, 120 Gt of C is supposed to be assimilated through photosynthetic activity of plants as the gross primary production (GPP) over global land area. In terms of climate change, GPP modelling is essential to understand carbon cycle and the balance of carbon budget over various ecosystems. One of the GPP modelling approaches uses light use efficiency that each vegetation type has a specific efficiency for consuming solar radiation related with temperature and humidity. Satellite data can be used to measure various meteorological and biophysical factors over vast areas, which can be used to quantify GPP. NASA Earth Observing System (EOS) program provides Moderate Resolution Imaging Spectroradiometer (MODIS)-derived global GPP product, namely MOD17A2H, on a daily basis. However, significant underestimation of MOD17A2H has been reported in Eastern Asia due to its dense forest distribution and humid condition during monsoon rainy season in summer. The objective of this study was to improve underestimation of MODIS GPP (MOD17A2H) by incorporating meteorological data-temperature, relative humidity, and solar radiation-of higher spatial resolution than data used in MOD17A2H. Landsat-based land cover maps of finer resolution observation and monitoring - global land cover (FROM-GLC) at 30m resolution were used for selection of light use efficiency (LUE). GPP (eq1. GPP = APAR×LUE) is computed by multiplication of APAR (IPAR×fPAR) and LUE (ɛ= ɛmax×T(°C)scalar×VPD(Pa)scalar, where, T is temperature, VPD is vapour pressure deficit) in this study. Meteorological data of Japanese 55-year Reanalysis (JRA-55, 0.56° grid, 3hr) were used for calculation of GPP in East Asia, including Eastern part of China, Korean peninsula, and Japan. Results were validated using flux tower-observed GPP data of AsiaFlux. Results showed that about 40% of underestimation of monthly average of MOD17A2H is confirmed and underestimation of MOD17A2 was improved from 42.3% and 60.4% to 8.3% and -26.2% for two flux tower sites (API site in Japan and GCK site in Korea), respectively. These improvements suggest that correction of LUE by finer land cover classification and/or better frequency of solar radiation data is effective where MOD17A2H does not work well. Further research will include evaluation of the proposed approach over areas in different climate conditions and environments.

Osteogenic response of human MSCs and osteoblasts to hydrophilic and hydrophobic nanostructured titanium implant surfaces.

PubMed

Lotz, Ethan M; Olivares-Navarrete, Rene; Berner, Simon; Boyan, Barbara D; Schwartz, Zvi

2016-12-01

Microstructured implant surfaces created by grit blasting and acid etching titanium (Ti) support osseointegration. This effect is further enhanced by storing in aqueous solution to retain hydrophilicity, but this also leads to surface nanostructure formation. The purpose of this study was to assess the contributions of nanostructures on the improved osteogenic response of osteoblast lineage cells to hydrophilic microstructured Ti. Human mesenchymal stem cells (MSCs) and normal human osteoblasts (NHOsts) were cultured separately on non-nanostructured/hydrophobic (SLA), nanostructured/hydrophilic (modSLA), or nanostructured/hydrophobic (SLAnano) Ti surfaces. XPS showed elevated carbon levels on SLA and SLAnano compared to modSLA. Contact angle measurements indicated only modSLA was hydrophilic. Confocal laser microscopy revealed minor differences in mean surface roughness. SEM showed the presence of nanostructures on modSLA and SLAnano. MSCs and NHOst cells exhibited similar morphology on the substrates and osteoblastic differentiation and maturation were greatest on modSLA. These results suggest that when the appropriate microstructure is present, hydrophilicity may play a greater role in stimulating MSC and NHOst osteoblastic differentiation and maturation than the presence of nanostructures generated during storage in an aqueous environment. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 3137-3148, 2016. © 2016 Wiley Periodicals, Inc.

Incipient evolution of Wolbachia compatibility types.

PubMed

Charlat, Sylvain; Riegler, Markus; Baures, Isabelle; Poinsot, Denis; Stauffer, Christian; Merçot, Hervé

2004-09-01

Cytoplasmic incompatibility (CI) is induced in arthropods by the maternally inherited bacterium Wolbachia. When infected males mate with uninfected females or with females bearing a different Wolbachia variant, paternal chromosomes behave abnormally and embryos die. This pattern can be interpreted as resulting from two bacterial effects: One (usually termed mod, for modification) would affect sperm and induce embryo death, unless Wolbachia is also present in the egg, which implies the existence of a second effect, usually termed resc, for rescue. The fact that CI can occur in crosses between males and females infected by different Wolbachia shows that mod and resc interact in a specific manner. In other words, different compatibility types, or mod/resc pairs seem to have diverged from one (or a few) common ancestor(s). We are interested in the process allowing the evolution of mod/resc pairs. Here this question is addressed experimentally after cytoplasmic injection into a single host species (Drosophila simulans) by investigating compatibility relationships between closely related Wolbachia variants naturally evolving in different dipteran hosts: D. simulans, Drosophila melanogaster, and Rhagoletis cerasi. Our results suggest that closely related bacteria can be totally or partially incompatible. The compatibility relationships observed can be explained using a formal description of the mod and resc functions, implying both qualitative and quantitative variations.

GPCR-ModSim: A comprehensive web based solution for modeling G-protein coupled receptors

PubMed Central

Esguerra, Mauricio; Siretskiy, Alexey; Bello, Xabier; Sallander, Jessica; Gutiérrez-de-Terán, Hugo

2016-01-01

GPCR-ModSim (http://open.gpcr-modsim.org) is a centralized and easy to use service dedicated to the structural modeling of G-protein Coupled Receptors (GPCRs). 3D molecular models can be generated from amino acid sequence by homology-modeling techniques, considering different receptor conformations. GPCR-ModSim includes a membrane insertion and molecular dynamics (MD) equilibration protocol, which can be used to refine the generated model or any GPCR structure uploaded to the server, including if desired non-protein elements such as orthosteric or allosteric ligands, structural waters or ions. We herein revise the main characteristics of GPCR-ModSim and present new functionalities. The templates used for homology modeling have been updated considering the latest structural data, with separate profile structural alignments built for inactive, partially-active and active groups of templates. We have also added the possibility to perform multiple-template homology modeling in a unique and flexible way. Finally, our new MD protocol considers a series of distance restraints derived from a recently identified conserved network of helical contacts, allowing for a smoother refinement of the generated models which is particularly advised when there is low homology to the available templates. GPCR- ModSim has been tested on the GPCR Dock 2013 competition with satisfactory results. PMID:27166369

ITER L-mode confinement database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaye, S.M.

This paper describes the content of an L-mode database that has been compiled with data from Alcator C-Mod, ASDEX, DIII, DIII-D, FTU, JET, JFT-2M, JT-60, PBX-M, PDX, T-10, TEXTOR, TFTR, and Tore-Supra. The database consists of a total of 2938 entries, 1881 of which are in the L-phase while 922 are ohmically heated only (OH). Each entry contains up to 95 descriptive parameters, including global and kinetic information, machine conditioning, and configuration. The paper presents a description of the database and the variables contained therein, and it also presents global and thermal scalings along with predictions for ITER.

The reinforcement effect of polyethylene fibre and composite impregnated glass fibre on fracture resistance of endodontically treated teeth: An in vitro study

PubMed Central

Luthria, Archana; Srirekha, A; Hegde, Jayshree; Karale, Rupali; Tyagi, Sanjana; Bhaskaran, Sajeev

2012-01-01

Aim: The aim of this study was to evaluate the fracture resistance of endodontically treated maxillary premolars with wide mesio-occluso-distal (MOD) cavities restored with either composite resin, or composite resin reinforced with different types of fibres. Materials and Methods: Fifty human maxillary premolars were selected. Five intact teeth served as positive controls. Endodontic therapy was carried out in the remaining forty-five teeth. Standardized MOD cavities were prepared in all the teeth. The teeth were restored with a nanocomposite using an incremental technique. These forty five teeth were randomly divided into three experimental groups (Group A, B and C) (n = 15). The teeth in Group A did not undergo any further procedures. The teeth in Group B and C were reinforced with composite impregnated glass fibre and polyethylene fibre, respectively. Fracture resistance was measured in Newtons (N). Results: The positive controls showed the highest mean fracture resistance (811.90 N), followed by Group B (600.49N), Group A (516.96N) and Group C (514.64N), respectively. One Way analysis of variance (ANOVA) test revealed a statistically significant difference between all the groups (P = 0.001). Post-hoc Tukey test revealed a moderately significant difference (P = 0.034) between Control and Group B, and a strongly significant difference between Control and Group A (P = 0.002), and Control and Group C (P = 0.001). Conclusions: Endodontic therapy and MOD cavity preparation significantly reduced the fracture resistance of endodontically treated maxillary premolars (P = 0.001). No statistically significant difference was found between the experimental groups (Group A, B and C) (P > 0.1). However, the fracture resistance of the composite impregnated glass fibre reinforced group was much higher than the others. PMID:23112487

Production of internal transport barriers via self-generated mean flows in Alcator C-Moda)

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Ernst, D. R.; Podpaly, Y. A.; Mikkelsen, D.; Howard, N. T.; Lee, Jungpyo; Reinke, M. L.; Rice, J. E.; Hughes, J. W.; Ma, Y.; Rowan, W. L.; Bespamyatnov, I.

2012-05-01

New results suggest that changes observed in the intrinsic toroidal rotation influence the internal transport barrier (ITB) formation in the Alcator C-Mod tokamak [E. S. Marmar and Alcator C-Mod group, Fusion Sci. Technol. 51, 261 (2007)]. These arise when the resonance for ion cyclotron range of frequencies (ICRF) minority heating is positioned off-axis at or outside of the plasma half-radius. These ITBs form in a reactor relevant regime, without particle or momentum injection, with Ti ≈ Te, and with monotonic q profiles (qmin < 1). C-Mod H-mode plasmas exhibit strong intrinsic co-current rotation that increases with increasing stored energy without external drive. When the resonance position is moved off-axis, the rotation decreases in the center of the plasma resulting in a radial toroidal rotation profile with a central well which deepens and moves farther off-axis when the ICRF resonance location reaches the plasma half-radius. This profile results in strong E × B shear (>1.5 × 105 rad/s) in the region where the ITB foot is observed. Gyrokinetic analyses indicate that this spontaneous shearing rate is comparable to the linear ion temperature gradient (ITG) growth rate at the ITB location and is sufficient to reduce the turbulent particle and energy transport. New and detailed measurement of the ion temperature demonstrates that the radial profile flattens as the ICRF resonance position moves off axis, decreasing the drive for the ITG the instability as well. These results are the first evidence that intrinsic rotation can affect confinement in ITB plasmas.

Processing effects on microstructure, percolation and resistive sensor properties of nickel-zirconium oxide cermet films on silicon substrates

NASA Astrophysics Data System (ADS)

Sundeen, John Edward, Jr.

Thin Ni-ZrO2 cermet films were developed on silicon substrates using solution based, metallo-organic deposition (MOD) technique. The nickel based cermet films on silicon are of interest for heater, temperature and flow sensor devices, particularly in automotive or aerospace applications at UP to 250°C. In this study, precursors for the NiO-ZrO2 composite films were derived from metal carboxylate and nitrate based solutions. Composition and heat treatment conditions were the main process variables for controlling the structure, particle size and morphology, on which the electrical properties depend. Electrical resistance behavior was studied for Ni-ZrO2 films with 25--78 vol.% Ni content. This Ni amount exceeds the percolation threshold for conduction. The dependence of the resistance on individual processing variables, including film thickness, ambient flow rate, sintering temperature and time, and specimen geometry was studied. Electrical characterization included establishing the percolative resistive behavior in the MOD Ni-ZrO2 films. A resistive percolation threshold (pc) at ˜25 vol.% Ni was found for 800°C sintered, 1mum thick Ni-ZrO2 films. Existing models including the general effective media (GEM) percolation equation, and mixture rules were used to develop a predictive expression for Ni-ZrO2 film resistance as a function of composition. Kinetic analysis of particle size in the 55 vol.% Ni cermet films was directly correlated to the sheet resistance (Rs) of the films. The temperature coefficient of resistance (TCR) was also correlated to R s, by the equation: (TCR)alpha = alphao - betaR s. These electrical characteristics make the films suitable for use as gas flow and temperature sensors. Calculated figure of merit (rho-TCR), values for the MOD Ni-ZrO2 films Compared favorably to commercial Pt and Ni based thin and thick film formulations used for heaters and thermal sensors. An added advantage of the MOD Ni-ZrO2, compared to the non-linear behavior of Ni, was that film resistance response to temperature is highly linear over the temperature range of 20--160°C. Select films could be heated to 45--100°C with a low (I2R) power input of 400mW-2W. Then films demonstrated stable hot resistance, high sensitivity and rapid response to gas flow. Significant accomplishments from this work included the development of: (a) MOD derived cermet films of 40--78 vol.% Ni, with high positive TCR of 2600--4250ppm/°C and Rs of 2.5--60%O/□/1mum which are highly suitable for thermal sensing applications, (b) A simple mixture rule rho = rhoo - m·VNi describing the film resistivity with composition; and (c) Expressions correlating film TCR and resistance to sintering time and temperature using particle growth kinetics.

Free-boundary toroidal Alfvén eigenmodes

NASA Astrophysics Data System (ADS)

Chen, Eugene Y.; Berk, H. L.; Breizman, B.; Zheng, L. J.

2011-05-01

A numerical study is presented for the n = 1 free-boundary toroidal Alfvén eigenmodes (TAE) in tokamaks, which shows that there is considerable sensitivity of n = 1 modes to the position of the conducting wall. An additional branch of the TAE is shown to emerge from the upper continuum as the ratio of conducting wall radius to plasma radius increases. Such phenomena arise in plasma equilibria with both circular and shaped cross sections, where the shaped profile studied here is similar to that found in Alcator C-Mod.

Pediatric Multiple Organ Dysfunction Syndrome: Promising Therapies

PubMed Central

Doctor, Allan; Zimmerman, Jerry; Agus, Michael; Rajasekaran, Surender; Wardenburg, Juliane Bubeck; Fortenberry, James; Zajicek, Anne; Typpo, Katri

2016-01-01

Objective To describe the state of the science, identify knowledge gaps, and offer potential future research questions regarding promising therapies for children with multiple organ dysfunction syndrome (MODS) presented during the Eunice Kennedy Shriver National Institute of Child Health and Human Development Workshop on Pediatric Multiple Organ Dysfunction Syndrome (March 26-27, 2015). Data Sources Literature review, research data, and expert opinion. Study Selection Not applicable. Data Extraction Moderated by an expert from the field, issues relevant to the association of MODS with a variety of conditions were presented, discussed and debated with a focus on identifying knowledge gaps and research priorities. Data Synthesis Summary of presentations and discussion supported and supplemented by relevant literature. Conclusions Among critically ill children, MODS is relatively common and associated with significant morbidity and mortality. For outcomes to improve, effective therapies aimed at preventing and treating this condition must be discovered and rigorously evaluated. In this manuscript, a number of potential opportunities to enhance current care are highlighted including the need for a better understanding of the pharmacokinetics and pharmacodynamics of medications, the effect of early and optimized nutrition, and the impact of effective glucose control in the setting of MODS. Additionally, a handful of the promising therapies either currently being implemented or developed are described. These include extracorporeal therapies, anti-cytokine therapies, anti-toxin treatments, anti-oxidant approaches and multiple forms of exogenous steroids. For the field to advance, these and other therapies must be assessed in rigorous manner and implemented accordingly. PMID:28248836

A Field Evaluation of the Hardy TB MODS Kit™ for the Rapid Phenotypic Diagnosis of Tuberculosis and Multi-Drug Resistant Tuberculosis

PubMed Central

Martin, Laura; Coronel, Jorge; Faulx, Dunia; Valdez, Melissa; Metzler, Mutsumi; Crudder, Chris; Castillo, Edith; Caviedes, Luz; Grandjean, Louis; Rodriguez, Mitzi; Friedland, Jon S.; Gilman, Robert H.; Moore, David A. J.

2014-01-01

Background Even though the WHO-endorsed, non-commercial MODS assay offers rapid, reliable TB liquid culture and phenotypic drug susceptibility testing (DST) at lower cost than any other diagnostic, uptake has been patchy. In part this reflects misperceptions about in-house assay quality assurance, but user convenience of one-stop procurement is also important. A commercial MODS kit was developed by Hardy Diagnostics (Santa Maria, CA, USA) with PATH (Seattle, WA, USA) to facilitate procurement, simplify procedures through readymade media, and enhance safety with a sealing silicone plate lid. Here we report the results from a large-scale field evaluation of the MODS kit in a government service laboratory. Methods & Findings 2446 sputum samples were cultured in parallel in Lowenstein-Jensen (LJ), conventional MODS and in the MODS kit. MODS kit DST was compared with conventional MODS (direct) DST and proportion method (indirect) DST. 778 samples (31.8%) were Mycobacterium tuberculosis culture-positive. Compared to conventional MODS the sensitivity, specificity, positive, and negative predictive values (95% confidence intervals) of the MODS Kit were 99.3% (98.3–99.8%), 98.3% (97.5–98.8%), 95.8% (94.0–97.1%), and 99.7% (99.3–99.9%). Median (interquartile ranges) time to culture-positivity (and rifampicin and isoniazid DST) was 10 (9–13) days for conventional MODS and 8.5 (7–11) for MODS Kit (p<0.01). Direct rifampicin and isoniazid DST in MODS kit was almost universally concordant with conventional MODS (97.9% agreement, 665/679 evaluable samples) and reference indirect DST (97.9% agreement, 687/702 evaluable samples). Conclusions MODS kit delivers performance indistinguishable from conventional MODS and offers a convenient, affordable alternative with enhanced safety from the sealing silicone lid. The availability in the marketplace of this platform, which conforms to European standards (CE-marked), readily repurposed for second-line DST in the near future, provides a fresh opportunity for improving equity of access to TB diagnosis and first and second-line DST in settings where the need is greatest. PMID:25225802

A field evaluation of the Hardy TB MODS Kit™ for the rapid phenotypic diagnosis of tuberculosis and multi-drug resistant tuberculosis.

PubMed

Martin, Laura; Coronel, Jorge; Faulx, Dunia; Valdez, Melissa; Metzler, Mutsumi; Crudder, Chris; Castillo, Edith; Caviedes, Luz; Grandjean, Louis; Rodriguez, Mitzi; Friedland, Jon S; Gilman, Robert H; Moore, David A J

2014-01-01

Even though the WHO-endorsed, non-commercial MODS assay offers rapid, reliable TB liquid culture and phenotypic drug susceptibility testing (DST) at lower cost than any other diagnostic, uptake has been patchy. In part this reflects misperceptions about in-house assay quality assurance, but user convenience of one-stop procurement is also important. A commercial MODS kit was developed by Hardy Diagnostics (Santa Maria, CA, USA) with PATH (Seattle, WA, USA) to facilitate procurement, simplify procedures through readymade media, and enhance safety with a sealing silicone plate lid. Here we report the results from a large-scale field evaluation of the MODS kit in a government service laboratory. 2446 sputum samples were cultured in parallel in Lowenstein-Jensen (LJ), conventional MODS and in the MODS kit. MODS kit DST was compared with conventional MODS (direct) DST and proportion method (indirect) DST. 778 samples (31.8%) were Mycobacterium tuberculosis culture-positive. Compared to conventional MODS the sensitivity, specificity, positive, and negative predictive values (95% confidence intervals) of the MODS Kit were 99.3% (98.3-99.8%), 98.3% (97.5-98.8%), 95.8% (94.0-97.1%), and 99.7% (99.3-99.9%). Median (interquartile ranges) time to culture-positivity (and rifampicin and isoniazid DST) was 10 (9-13) days for conventional MODS and 8.5 (7-11) for MODS Kit (p<0.01). Direct rifampicin and isoniazid DST in MODS kit was almost universally concordant with conventional MODS (97.9% agreement, 665/679 evaluable samples) and reference indirect DST (97.9% agreement, 687/702 evaluable samples). MODS kit delivers performance indistinguishable from conventional MODS and offers a convenient, affordable alternative with enhanced safety from the sealing silicone lid. The availability in the marketplace of this platform, which conforms to European standards (CE-marked), readily repurposed for second-line DST in the near future, provides a fresh opportunity for improving equity of access to TB diagnosis and first and second-line DST in settings where the need is greatest.

Posttest data analysis and assessment of TRAC-BD1/MOD1 with data from a Full Integral Simulation Test (FIST) power transient experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wheatley, P.D.; Wagner, K.C.

The FIST power transient test 6PMC2 was analyzed to further the understanding of the FIST facility and provide an assessment of TRAC-BD1/MOD1. FIST power transient 6PMC2 investigated the thermal-hydraulic response following inadvertent closure of the main steam isolation valve and the subsequent failure of the reactor to scram. Failure of the high pressure core spray system was also assumed, resulting on only the reactor core isolation cooling flow for inventory makeup during the transient. The experiment was a sensitivity study with relatively high core power and low makeup rates. This study provides one of the first opportunities to assess TRAC-BD1/MOD1more » under power transient and natural circulation conditions with data from a facility with prototypical BWR geometry. The power transient test was analyzed with emphasis on the following phenomena; (a) the system pressure response, (b) the natural circulation flows and rates, and (c) the heater rod cladding temperature response. Based on the results of this study, TRAC-BD1/MOD1 can be expected to calculate the thermal-hydraulic behavior of a BWR during a power transient.« less

Macroscopic character of composite high-temperature superconducting wires

NASA Astrophysics Data System (ADS)

Kivelson, S. A.; Spivak, B.

2015-11-01

The "d -wave" symmetry of the superconducting order in the cuprate high temperature superconductors is a well established fact [J. Tsuei and J. R. Kirtley, Rev. Mod. Phys. 72, 969 (2000), 10.1103/RevModPhys.72.969 and D. J. Vanharlingen, Rev. Mod. Phys. 67, 515 (1995), 10.1103/RevModPhys.67.515], and one which identifies them as "unconventional." However, in macroscopic contexts—including many potential applications (i.e., superconducting "wires")—the material is a composite of randomly oriented superconducting grains in a metallic matrix, in which Josephson coupling between grains mediates the onset of long-range phase coherence. [See, e.g., D. C. Larbalestier et al., Nat. Mater. 13, 375 (2014), 10.1038/nmat3887, A. P. Malozemoff, MRS Bull. 36, 601 (2011), 10.1557/mrs.2011.160, and K. Heine et al., Appl. Phys. Lett. 55, 2441 (1989), 10.1063/1.102295] Here we analyze the physics at length scales that are large compared to the size of such grains, and in particular the macroscopic character of the long-range order that emerges. While X Y -superconducting glass order and macroscopic d -wave superconductivity may be possible, we show that under many circumstances—especially when the d -wave superconducting grains are embedded in a metallic matrix—the most likely order has global s -wave symmetry.

Conceptual design of the 7 megawatt Mod-5B wind turbine generator

NASA Technical Reports Server (NTRS)

Douglas, R. R.

1982-01-01

Similar to MOD-2, the MOD-5B wind turbine generator system is designed for the sole purpose of providing electrical power for distribution by a major utility network. The objectives of the MOD-2 and MOD-5B programs are essentially identical with one important exception; the cost-of-electricity (COE) target is reduced from 4 cent/Kwhr on MOD-2 to 3 cent/Kwhr on MOD-5B, based on mid 1977 dollars and large quantity production. The MOD-5B concept studies and eventual concept selection confirmed that the program COE targets could not only be achieved but substantially bettered. Starting from the established MOD-2 technology as a base, this achievement resulted from a combination of concept changes, size changes, and design refinements. The result of this effort is a wind turbine system that can compete with conventional power generation over significant geographical areas, increasing commercial market potential by an order of magnitude.

Assessment of Global Carbon Dioxide Concentration Using MODIS and GOSAT Data

PubMed Central

Guo, Meng; Wang, Xiufeng; Li, Jing; Yi, Kunpeng; Zhong, Guosheng; Tani, Hiroshi

2012-01-01

Carbon dioxide (CO2) is the most important greenhouse gas (GHG) in the atmosphere and is the greatest contributor to global warming. CO2 concentration data are usually obtained from ground observation stations or from a small number of satellites. Because of the limited number of observations and the short time series of satellite data, it is difficult to monitor CO2 concentrations on regional or global scales for a long time. The use of the remote sensing data such as the Advanced Very High Resolution Radiometer (AVHRR) or Moderate Resolution Imaging Spectroradiometer (MODIS) data can overcome these problems, particularly in areas with low densities of CO2 concentration watch stations. A model based on temperature (MOD11C3), vegetation cover (MOD13C2 and MOD15A2) and productivity (MOD17A2) of MODIS (which we have named the TVP model) was developed in the current study to assess CO2 concentrations on a global scale. We assumed that CO2 concentration from the Thermal And Near infrared Sensor for carbon Observation (TANSO) aboard the Greenhouse gases Observing SATellite (GOSAT) are the true values and we used these values to check the TVP model accuracy. The results indicate that the accuracy of the TVP model is different in different continents: the greatest Pearson’s correlation coefficient (R2) was 0.75 in Eurasia (RMSE = 1.16) and South America (RMSE = 1.17); the lowest R2 was 0.57 in Australia (RMSE = 0.73). Compared with the TANSO-observed CO2 concentration (XCO2), we found that the accuracy throughout the World is between −2.56∼3.14 ppm. Potential sources of TVP model uncertainties were also analyzed and identified. PMID:23443383

Assessment of global carbon dioxide concentration using MODIS and GOSAT data.

PubMed

Guo, Meng; Wang, Xiufeng; Li, Jing; Yi, Kunpeng; Zhong, Guosheng; Tani, Hiroshi

2012-11-26

Carbon dioxide (CO(2)) is the most important greenhouse gas (GHG) in the atmosphere and is the greatest contributor to global warming. CO(2) concentration data are usually obtained from ground observation stations or from a small number of satellites. Because of the limited number of observations and the short time series of satellite data, it is difficult to monitor CO(2) concentrations on regional or global scales for a long time. The use of the remote sensing data such as the Advanced Very High Resolution Radiometer (AVHRR) or Moderate Resolution Imaging Spectroradiometer (MODIS) data can overcome these problems, particularly in areas with low densities of CO(2) concentration watch stations. A model based on temperature (MOD11C3), vegetation cover (MOD13C2 and MOD15A2) and productivity (MOD17A2) of MODIS (which we have named the TVP model) was developed in the current study to assess CO(2) concentrations on a global scale. We assumed that CO(2) concentration from the Thermal And Near infrared Sensor for carbon Observation (TANSO) aboard the Greenhouse gases Observing SATellite (GOSAT) are the true values and we used these values to check the TVP model accuracy. The results indicate that the accuracy of the TVP model is different in different continents: the greatest Pearson's correlation coefficient (R2) was 0.75 in Eurasia (RMSE = 1.16) and South America (RMSE = 1.17); the lowest R2 was 0.57 in Australia (RMSE = 0.73). Compared with the TANSO-observed CO(2) concentration (XCO(2)), we found that the accuracy throughout the World is between -2.56~3.14 ppm. Potential sources of TVP model uncertainties were also analyzed and identified.

Moteurs piézo-électriques à onde progressive : I. Modélisation de la conversion d'énergie mécanique à l'interface stator/rotor

NASA Astrophysics Data System (ADS)

Minotti, P.; Le Moal, P.; Buchaillot, L.; Ferreira, A.

1996-10-01

The modeling of traveling wave type piezoelectric motors involves a large variety of mechanical and physical phenomena and therefore leads to numerous approaches and models. The latter, mainly based on phenomenological and numerical (based on Finite Element Method) analyses, are not suitable for current objectives oriented toward the development of efficient C.A.D. tools. As a result, an attempt is done to investigate analytical approaches, in order to theoretically model the mechanical energy conversion at the stator/rotor interface. This paper is the first in a serie of three articles devoted to the modeling of such rotative motors. After a short description of the operating principles specific to the piezomotors, the mechanical and tribological assumptions made for the driving mechanism of the rotor are briefly described. Then it is shown that the kinematic and dynamic modeling of the stator, combined with the static representation of the stator/rotor interface, gives an efficient way in order to perform the calculation of the loading characteristics of the driving shaft. Finally, the specifications of a new software named C.A.S.I.M.M.I.R.E., which has been recently developed on the basis of our earlier mechanical modeling, are described. In the last of these three papers, the theoretical simulations performed on SHINSEI Japanese motors will show to be close to the experimental data and that the results reported in this paper will lead to the structural optimization of future traveling wave ultrasonic motors. La modélisation des moteurs piézo-électriques à onde progressive implique une grande variété de phénomènes physiques et mécaniques. Cette variété conduit à des approches et modèles tout aussi nombreux et variés, qui reposent principalement sur des analyses phénoménologiques et numériques (Méthode Élements Finis), et ne permettent pas de répondre aux éxigences actuelles concernant le développement d'outils C.A.O. performants. Cette nécessité nous a conduits à développer une modélisation théorique analytique de la conversion d'énergie à l'interface stator/rotor. Ce papier est le premier d'une série de trois articles consacrés à la modélisation des moteurs piézo-électriques rotatifs. Après une rapide description des principes de fonctionnement de ces piézomoteurs, les hypothèses mécaniques et tribologiques concernant le mécanisme d'entraînement du rotor sont énoncées succinctement. On démontre ensuite que la modélisation cinématique et dynamique du stator, combinée à une représentation statique du comportement à l'interface stator/rotor, autorise l'évaluation des caractéristiques en charge des moteurs à onde progressive. Enfin, le logiciel baptisé C.A.S.I.M.M.I.R.E., récemment développé sur la base de la modélisation mécanique précédente, est présenté puis testé. Dans le dernier article de cette série, nous confirmerons la validité des simulations théoriques issues de ce logiciel, à partir de la caractérisation expérimentale de moteurs japonais de la firme SHINSEI. Ce nouveau logiciel constitue d'ores et déjà un outil performant en vue de l'optimisation des futurs moteurs à onde progressive, et a déjà fait l'objet d'une première exploitation en milieu industriel.

Geostatistical interpolation of individual average monthly temperature supported by MODIS MOD11C3 product

NASA Astrophysics Data System (ADS)

Perčec Tadić, M.

2010-09-01

The increased availability of satellite products of high spatial and temporal resolution together with developing user support, encourages the climatologists to use this data in research and practice. Since climatologists are mainly interested in monthly or even annual averages or aggregates, this high temporal resolution and hence, large amount of data, can be challenging for the less experienced users. Even if the attempt is made to aggregate e. g. the 15' (temporal) MODIS LST (land surface temperature) to daily temperature average, the development of the algorithm is not straight forward and should be done by the experts. Recent development of many temporary aggregated products on daily, several days or even monthly scale substantially decrease the amount of satellite data that needs to be processed and rise the possibility for development of various climatological applications. Here the attempt is presented in incorporating the MODIS satellite MOD11C3 product (Wan, 2009), that is monthly CMG (climate modelling 0.05 degree latitude/longitude grids) LST, as predictor in geostatistical interpolation of climatological data in Croatia. While in previous applications, e. g. in Climate Atlas of Croatia (Zaninović et al. 2008), the static predictors as digital elevation model, distance to the sea, latitude and longitude were used for the interpolation of monthly, seasonal and annual 30-years averages (reference climatology), here the monthly MOD11C3 is used to support the interpolation of the individual monthly average in the regression kriging framework. We believe that this can be a valuable show case of incorporating the remote sensed data for climatological application, especially in the areas that are under-sampled by conventional observations. Zaninović K, Gajić-Čapka M, Perčec Tadić M et al (2008) Klimatski atlas Hrvatske / Climate atlas of Croatia 1961-1990, 1971-2000. Meteorological and Hydrological Service of Croatia, Zagreb, pp 200. Wan Z, 2009: Collection-5 MODIS Land Surface Temperature Products Users' Guide, ICESS, University of California, Santa Barbara, pp 30.

Progress towards modeling tokamak boundary plasma turbulence and understanding its role in setting divertor heat flux widths

NASA Astrophysics Data System (ADS)

Chen, Bin

2017-10-01

QCMs (quasi-coherent modes) are well characterized in the edge of Alcator C-Mod, when operating in the Enhanced Dα (EDA) H-mode, a promising alternative regime for ELM (edge localized modes) suppressed operation. To improve the understanding of the physics behind the QCMs, three typical C-Mod EDA H-Mode discharges are simulated by BOUT + + using a six-field two-fluid model (based on the Braginskii equations). The simulated characteristics of the frequency versus wave number spectra of the modes is in reasonable agreement with phase contrast imaging data. The key simulation results are: 1) Linear spectrum analysis and the nonlinear phase relationship indicate the dominance of resistive-ballooning modes and drift-Alfven wave instabilities; 2) QCMs originate inside the separatrix; (3) magnetic flutter causes the mode spreading into the SOL; 4) the boundary electric field Er changes the turbulent characteristics of the QCMs and controls edge transport and the divertor heat flux width; 5) the magnitude of the divertor heat flux depends on the physics models, such as sources and sinks, sheath boundary conditions, and parallel heat flux limiting coefficient. The BOUT + + simulations have also been performed for inter-ELM periods of DIII-D and EAST discharges, and similar quasi-coherent modes have been found. The parallel electron heat fluxes projected onto the target from these BOUT + + simulations follow the experimental heat flux width scaling, in particular the inverse dependence of the width on the poloidal magnetic field with an outlier. Further turbulence statistics analysis shows that the blobs are generated near the pedestal peak gradient region inside the separatrix and contribute to the transport of the particle and heat in the SOL region. To understand the Goldston heuristic drift-based model, results will also be presented from self-consistent transport simulations with the electric and magnetic drifts in BOUT + + and with the sheath potential included in the SOL. Work supported by LLNL under Contract DE-AC52-07NA27344. This work was also supported by US DOE Grant DE-FC02-99ER54512, using Alcator C-Mod, a DOE Office of Science User Facility, and under the auspices of the CSC (No. 201506340019).

Muscle metabolic and neuromuscular determinants of fatigue during cycling in different exercise intensity domains

PubMed Central

Black, Matthew I.; Jones, Andrew M.; Blackwell, Jamie R.; Bailey, Stephen J.; Wylie, Lee J.; McDonagh, Sinead T. J.; Thompson, Christopher; Kelly, James; Sumners, Paul; Mileva, Katya N.; Bowtell, Joanna L.

2017-01-01

Lactate or gas exchange threshold (GET) and critical power (CP) are closely associated with human exercise performance. We tested the hypothesis that the limit of tolerance (Tlim) during cycle exercise performed within the exercise intensity domains demarcated by GET and CP is linked to discrete muscle metabolic and neuromuscular responses. Eleven men performed a ramp incremental exercise test, 4–5 severe-intensity (SEV; >CP) constant-work-rate (CWR) tests until Tlim, a heavy-intensity (HVY; GET) CWR test until Tlim, and a moderate-intensity (MOD; 0.05) muscle metabolic milieu (i.e., low pH and [PCr] and high [lactate]) was attained at Tlim (approximately 2–14 min) for all SEV exercise bouts. The muscle metabolic perturbation was greater at Tlim following SEV compared with HVY, and also following SEV and HVY compared with MOD (all P < 0.05). The normalized M-wave amplitude for the vastus lateralis (VL) muscle decreased to a similar extent following SEV (−38 ± 15%), HVY (−68 ± 24%), and MOD (−53 ± 29%), (P > 0.05). Neural drive to the VL increased during SEV (4 ± 4%; P < 0.05) but did not change during HVY or MOD (P > 0.05). During SEV and HVY, but not MOD, the rates of change in M-wave amplitude and neural drive were correlated with changes in muscle metabolic ([PCr], [lactate]) and blood ionic/acid-base status ([lactate], [K+]) (P < 0.05). The results of this study indicate that the metabolic and neuromuscular determinants of fatigue development differ according to the intensity domain in which the exercise is performed. NEW & NOTEWORTHY The gas exchange threshold and the critical power demarcate discrete exercise intensity domains. For the first time, we show that the limit of tolerance during whole-body exercise within these domains is characterized by distinct metabolic and neuromuscular responses. Fatigue development during exercise greater than critical power is associated with the attainment of consistent “limiting” values of muscle metabolites, whereas substrate availability and limitations to muscle activation may constrain performance at lower intensities. PMID:28008101

Verification of GENE and GYRO with L-mode and I-mode plasmas in Alcator C-Mod

DOE PAGES

Mikkelsen, D. R.; Howard, N. T.; White, A. E.; ...

2018-04-25

Here, verification comparisons are carried out for L-mode and I-mode plasma conditions in Alcator C-Mod. We compare linear and nonlinear ion-scale calculations by the gyrokinetic codes GENE and GYRO to each other and to the experimental power balance analysis. The two gyrokinetic codes' linear growth rates and real frequencies are in good agreement throughout all the ion temperature gradient mode branches and most of the trapped electron mode branches of the kyρs spectra at r/a = 0.65, 0.7, and 0.8. The shapes of the toroidal mode spectra of heat fluxes in nonlinear simulations are very similar for k yρ smore » ≤ 0.5, but in most cases GENE has a relatively higher heat flux than GYRO at higher mode numbers.« less

Ohmic ITBs in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Rowan, William L.; Bespamyatnov, Igor O.; Fiore, C. L.; Dominguez, A.; Hubbard, A. E.; Ince-Cushman, A.; Greenwald, M. J.; Lin, L.; Marmar, E. S.; Reinke, M.; Rice, J. E.; Zhurovich, K.

2007-11-01

Internal transport barrier (ITB) plasmas can arise spontaneously in Ohmic Alcator C-Mod plasmas. The operational prescription for the ITB include formation of an EDA H-mode in a toroidal magnetic field that is ramping down and a subsequent increase in the toroidal magnetic field. Like ITBs generated with off-axis ICRF heating, these have peaked pressure profiles which can be suppressed by on-axis ICRF heating. Recent work on onset conditions for the ICRF generated ITB (K. Zhurovich, et al., To be published in Nuclear Fusion) demonstrates that the broadening of the ion temperature profile due to off-axis ICRF reduces the ion temperature gradient and suppreses the ITG instability driven particle flux as the primary mechanism for ITB formation. The object of this study is to examine the characteristics of Ohmic ITBs to find whether this model for onset is supported.

Model Development for VDE Computations in NIMROD

NASA Astrophysics Data System (ADS)

Bunkers, K. J.; Sovinec, C. R.

2017-10-01

Vertical displacement events (VDEs) and the disruptions associated with them have potential for causing considerable physical damage to ITER and other tokamak experiments. We report on simulations of generic axisymmetric VDEs and a vertically unstable case from Alcator C-MOD using the NIMROD code. Previous calculations have been done with closures for heat flux and viscous stress. Initial calculations show that halo current width is dependent on temperature boundary conditions, and so transport together with plasma-surface interaction may play a role in determining halo currents in experiments. The behavior of VDEs with Braginskii thermal conductivity and viscosity closures and Spitzer-like resistivity are investigated for both the generic axisymmetric VDE case and the C-MOD case. This effort is supported by the U.S. Dept. of Energy, Award Numbers DE-FG02-06ER54850 and DE-FC02-08ER54975.

Verification of GENE and GYRO with L-mode and I-mode plasmas in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikkelsen, D. R.; Howard, N. T.; White, A. E.

Here, verification comparisons are carried out for L-mode and I-mode plasma conditions in Alcator C-Mod. We compare linear and nonlinear ion-scale calculations by the gyrokinetic codes GENE and GYRO to each other and to the experimental power balance analysis. The two gyrokinetic codes' linear growth rates and real frequencies are in good agreement throughout all the ion temperature gradient mode branches and most of the trapped electron mode branches of the kyρs spectra at r/a = 0.65, 0.7, and 0.8. The shapes of the toroidal mode spectra of heat fluxes in nonlinear simulations are very similar for k yρ smore » ≤ 0.5, but in most cases GENE has a relatively higher heat flux than GYRO at higher mode numbers.« less

Outer midplane scrape-off layer profiles and turbulence in simulations of Alcator C-Mod inner-wall limited discharges

DOE PAGES

Halpern, Federico D.; LaBombard, Brian; Terry, James L.; ...

2017-06-27

A region of steep plasma gradients, the so-called ”narrow-feature”, has been found in the near scrape-off layer (SOL) of inner-wall limited (IWL) discharges. Dedicated IWL discharges were carried out in Alcator C-Mod [E.S. Marmar et al., Nucl. Fusion 55, (2015)] to study this phenomenon, allowing detailed observations of the plasma profiles and fluctuations. Langmuir probe (LP) measurements show a clear two decay length n e and T e profile structure at the outer midplane. The Gas-Puff Imaging (GPI) diagnostic shows large turbulent fluctuations across the last closed flux-surface, hence supporting the hypothesis that turbulent phenomena play a role in settingmore » the profile steepness. We have carried out the flux-driven non-linear turbulence simulations of two C-Mod discharges which allows a three-way comparison between LP, GPI, and simulation data. Observations and simulations correlate the steep gradient region characterizing the narrow feature with sheared poloidal flows and a deviation of the plasma potential from its floating value. Furthermore, the E x B shear rate exceeds the linear ballooning growth rate, indicating that the narrow feature could result from the effects of sheared flows, although causality could not be established. The fluctuation level in the narrow feature remains of order unity across the entire SOL, indicating that the transport reduction in the near-SOL cannot result from a simple quench rule.« less

Outer midplane scrape-off layer profiles and turbulence in simulations of Alcator C-Mod inner-wall limited discharges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halpern, Federico D.; LaBombard, Brian; Terry, James L.

A region of steep plasma gradients, the so-called ”narrow-feature”, has been found in the near scrape-off layer (SOL) of inner-wall limited (IWL) discharges. Dedicated IWL discharges were carried out in Alcator C-Mod [E.S. Marmar et al., Nucl. Fusion 55, (2015)] to study this phenomenon, allowing detailed observations of the plasma profiles and fluctuations. Langmuir probe (LP) measurements show a clear two decay length n e and T e profile structure at the outer midplane. The Gas-Puff Imaging (GPI) diagnostic shows large turbulent fluctuations across the last closed flux-surface, hence supporting the hypothesis that turbulent phenomena play a role in settingmore » the profile steepness. We have carried out the flux-driven non-linear turbulence simulations of two C-Mod discharges which allows a three-way comparison between LP, GPI, and simulation data. Observations and simulations correlate the steep gradient region characterizing the narrow feature with sheared poloidal flows and a deviation of the plasma potential from its floating value. Furthermore, the E x B shear rate exceeds the linear ballooning growth rate, indicating that the narrow feature could result from the effects of sheared flows, although causality could not be established. The fluctuation level in the narrow feature remains of order unity across the entire SOL, indicating that the transport reduction in the near-SOL cannot result from a simple quench rule.« less

Measurements of molybdenum radiation in the Alcator C-Mod tokamak using a multilayer mirror soft x-ray polychromator

NASA Astrophysics Data System (ADS)

May, M. J.; Finkenthal, M.; Regan, S. P.; Moos, H. W.; Terry, J. L.; Graf, M. A.; Fournier, K.; Goldstein, W. L.

1995-01-01

A photometrically calibrated polychromator utilizing layered synthetic microstructure coated flats (also known as multilayer mirrors, MLMs) as dispersive elements is operating on the Alcator C-Mod tokamak to measure the molybdenum emissions in the XUV. Molybdenum, the first wall material in C-Mod, is the dominant high Z impurity in the plasma. Three spectral regions are measured by three separate MLM-detector channels. The characteristic charge states in the region between 30-40 Å are Mo xv to Mo xx, between 65-90 Å are Mo xxiv to Mo xxvi, and between 110-130 Å are Mo xxxi and Mo xxxii. The instrument's spectral resolution varies from 0.4 Å at λ=30 Å to 7 Å at λ=130 Å. The temporal resolution is typically 1.0 ms, but sampling rates of less than 1 ms are possible. The instrument was photometrically calibrated at The Johns Hopkins University using a Manson soft x-ray light source. Power loss estimates from Mo xxiv to Mo xxvi, Mo xxxi, and Mo xxxii have been obtained during ohmic and ICRF plasmas using the mist transport code to model the molybdenum charge state distributions in the plasma. The Mo concentrations have also been determined. Mo contributes ˜0.1 to the Zeff of 1.3 during ohmic plasmas. This contribution increases during ICRF heating to ˜0.5 of the Zeff of 2. The polychromator functions as a time-resolved soft x-ray emission power loss monitor.

In Vitro and in Vivo Characterization of MOD-4023, a Long-Acting Carboxy-Terminal Peptide (CTP)-Modified Human Growth Hormone.

PubMed

Hershkovitz, Oren; Bar-Ilan, Ahuva; Guy, Rachel; Felikman, Yana; Moschcovich, Laura; Hwa, Vivian; Rosenfeld, Ron G; Fima, Eyal; Hart, Gili

2016-02-01

MOD-4023 is a novel long-acting version of human growth hormone (hGH), containing the carboxy-terminal peptide (CTP) of human chorionic gonadotropin (hCG). MOD-4023 is being developed as a treatment for adults and children with growth hormone deficiency (GHD), which would require fewer injections than currently available GH formulations and thus reduce patient discomfort and increase compliance. This study characterizes MOD-4023's binding affinities for the growth hormone receptor, as well as the pharmacokinetic and pharmacodynamics, toxicology, and safety profiles of repeated dosing of MOD-4023 in Sprague-Dawley rats and Rhesus monkeys. Although MOD-4023 exhibited reduced in vitro potency and lower affinity to the GH receptor than recombinant hGH (rhGH), administration of MOD-4023 every 5 days in rats and monkeys resulted in exposure comparable to daily rhGH, and the serum half-life of MOD-4023 was significantly longer. Repeated administration of MOD-4023 led to elevated levels of insulin-like growth factor 1 (IGF-1), and twice-weekly injections of MOD-4023 resulted in larger increase in weight gain with fewer injections and a lower accumulative hGH dose. Thus, the increased half-life of MOD-4023 in comparison to hGH may increase the frequency of protein-receptor interactions and compensate for its decreased in vitro potency. MOD-4023 was found to be well-tolerated in rats and monkeys, with minimal adverse events, suggesting an acceptable safety profile. These results provide a basis for the continued clinical development of MOD-4023 as a novel treatment of GHD in children and adults.

The General Electric MOD-1 wind turbine generator program

NASA Technical Reports Server (NTRS)

Poor, R. H.; Hobbs, R. B.

1979-01-01

The design, fabrication, installation and checkout of MOD-1, a megawatt class wind turbine generator which generates utility grade electrical power, is described. A MOD-1/MOD-1A tradeoff study is discussed.

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Astrophysics Data System (ADS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-08-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

MOD-0A 200 kW wind turbine generator design and analysis report

NASA Technical Reports Server (NTRS)

Anderson, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-01-01

The design, analysis, and initial performance of the MOD-OA 200 kW wind turbine generator at Clayton, NM is documented. The MOD-OA was designed and built to obtain operation and performance data and experience in utility environments. The project requirements, approach, system description, design requirements, design, analysis, system tests, installation, safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the wind turbine are discussed. The design and analysis of the rotor, drive train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electricl system, and control systems are presented. The rotor includes the blades, hub, and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control are discussed. Systems analyses on dynamic loads and fatigue are presented.

Etude du comportement et de la modélisation viscoplastique du zircaloy 4recristallisé sous chargements monotones et cycliques uni et multiaxes

NASA Astrophysics Data System (ADS)

Delobelle, P.; Robinet, P.

1994-08-01

The results of experiment performed on a recrystallized zircaloy 4 alloy in the intermediate temperature domain 20 leqslant T leqslant 400 ^{circ}C are presented. To characterize the anisotropy, especially at 350 ^{circ}C, the tests were made under both monotonic and cyclic uni- and bidirectional loadings, i.e. tension-compression, tension-torsion and tension-internal pressure tests. The different anisotropy coefficients and especially R^p = \\varepsilon^p_{θθ} /\\varepsilon^ p _ {{^-_-}{^-_-} } seem to be temperature independent. An important feature of the behavior of this alloy in the neighbourhood of 300 ^{circ}C is attributed to the dislocations-point defects interactions (dynamic strain aging), phenomena often observed in the solid solutions. For the 2D cyclic non proportional loadings it is shown that a weak supplementary hardening appears, which is a function of the degree of the phase lag. We propose to particularize and to apply a unified viscoplastic model with internal variables to the considered alloy, as the model as already been developed and identified elsewhere for other isotropic materials. From a general point of view the introduction of the anisotropy in the model is made by four tensors of rank 4 ; [ M] is assigned to the flow directions, [ N] to the linear parts of the kinematical hardening variables and [ Q] , [ R] respectively to the dynamic and static recoveries of these tensorial variables. This phenomenological formulation leads to a correct representation of the set of the experimental results presented at 350 ^{circ}C, which provides an a posteriori confirmation of the formalism used. On étudie, entre 20 et 400 ^{circ}C, à l'aide d'essais sous chargements multiaxiaux monotones et cycliques (traction, torsion et pression interne) les propriétés viscoplastiques anisotropes de tube de zircaloy 4 recristallisé. A la température de 350 ^{circ}C, l'anisotropie a été quantifiée de façon détaillée. Les quelques résultats obtenus à la température ambiante ainsi que l'indépendance du rapport R^p = \\varepsilon^p_{θθ}/\\varepsilon^ p_{{^-_-}{^-_-} } avec la température laissent supposer que l'ensemble des coefficients d'anisotropie ne dépendent pas de la température. Par contre, la fluidité de cet alliage présente un minimum très marqué au voisinage de 300 ^{circ}C. Ce comportement est imputable au vieillissement dynamique fréquemment observé dans les solutions solides d'insertion. Lors d'un chargement cyclique hors phase (traction-torsion déphasée à 90^{circ}) ce matériau présente un léger durcissement supplémentaire. On propose l'extension au cas du zircaloy 4 de la formulation d'un modèle viscoplastique unifié développé et identifié par ailleurs sur d'autres matériaux initialement isotropes. D'une manière générale, l'introduction de l'anisotropie dans ce modèle s'effectue par l'intermédiaire de quatre tenseurs d'ordre 4 affectant les directions d'écoulement [ M] , les parties linéaires des écrouissages cinématiques [ N] , ainsi que les restaurations dynamiques [ Q] et statiques [ R] de ces mêmes variables d'écrouissage. L'identification de ce modèle est discutée et réalisée à 350 ^{circ}C. On montre l'adéquation du formalisme à appréhender l'ensemble des caractéristiques mécaniques de cet alliage.

Spatial distributions ofC3 and C4 grass functional types in the U.S. great plains and their despendency on inter-annual climate variability

USDA-ARS?s Scientific Manuscript database

Grassland ecosystems in North America are primarily composed of C3 and C4 plant functional types (PFTs) with their relative cover varying spatially and temporally. This study used 500-m MODIS surface reflectance products (MOD09A1) from 2000 to 2009 to extract an NDVI time series of C3 and C4 PFTs in...

Ten Years of Cloud Optical and Microphysical Retrievals from MODIS

NASA Technical Reports Server (NTRS)

Platnick, Steven; King, Michael D.; Wind, Galina; Hubanks, Paul; Arnold, G. Thomas; Amarasinghe, Nandana

2010-01-01

The MODIS cloud optical properties algorithm (MOD06/MYD06 for Terra and Aqua MODIS, respectively) has undergone extensive improvements and enhancements since the launch of Terra. These changes have included: improvements in the cloud thermodynamic phase algorithm; substantial changes in the ice cloud light scattering look up tables (LUTs); a clear-sky restoral algorithm for flagging heavy aerosol and sunglint; greatly improved spectral surface albedo maps, including the spectral albedo of snow by ecosystem; inclusion of pixel-level uncertainty estimates for cloud optical thickness, effective radius, and water path derived for three error sources that includes the sensitivity of the retrievals to solar and viewing geometries. To improve overall retrieval quality, we have also implemented cloud edge removal and partly cloudy detection (using MOD35 cloud mask 250m tests), added a supplementary cloud optical thickness and effective radius algorithm over snow and sea ice surfaces and over the ocean, which enables comparison with the "standard" 2.1 11m effective radius retrieval, and added a multi-layer cloud detection algorithm. We will discuss the status of the MOD06 algorithm and show examples of pixellevel (Level-2) cloud retrievals for selected data granules, as well as gridded (Level-3) statistics, notably monthly means and histograms (lD and 2D, with the latter giving correlations between cloud optical thickness and effective radius, and other cloud product pairs).

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Farrell, R.; Hindes, C.; Battista, R.; Connelly, M.; Cronin, M.; Howarth, R.; Donahue, A.; Slate, E.; Stotts, R.; Lacy, R.

1988-01-01

The study of high power kinematic Stirling engines for transportation use, testing of Mod I and Mod II Stirling engines, and component development activities are summarized. Mod II development testing was performed to complete the development of the basic engine and begin characterization of performance. Mod I engines were used for Mod II component development and to obtain independent party (U.S. Air Force) evaluation of Stirling engine vehicle performance.

A comparison of three organ dysfunction scores: MODS, SOFA and LOD for predicting ICU mortality in critically ill patients.

PubMed

Khwannimit, Bodin

2007-06-01

To compare the validity of the Multiple Organ Dysfunction Score (MODS), Sequential Organ Failure Assessment (SOFA), and Logistic Organ Dysfunction Score (LOD) for predicting ICU mortality of Thai critically ill patients. A retrospective study was made of prospective data collected between the 1st July 2004 and 31st March 2006 at Songklanagarind Hospital. One thousand seven hundred and eighty two patients were enrolled in the present study. Two hundred and ninety three (16.4%) deaths were recorded in the ICU. The areas under the Receiver Operating Curves (A UC) for the prediction of ICU mortality the results were 0.861 for MODS, 0.879 for SOFA and 0.880 for LOD. The AUC of SOFA and LOD showed a statistical significance higher than the MODS score (p = 0.014 and p = 0.042, respectively). Of all the models, the neurological failure score showed the best correlation with ICU mortality. All three organ dysfunction scores satisfactorily predicted ICU mortality. The LOD and neurological failure had the best correlation with ICU outcome.

Installation and checkout of the DOE/NASA Mod-1 2000-kW wind turbine generator

NASA Technical Reports Server (NTRS)

Puthoff, R. L.; Collins, J. L.; Wolf, R. A.

1980-01-01

The paper describes the DOE/NASA Mod-1 wind turbine generator, its assembly and testing, and its installation at Boone, North Carolina. The paper concludes with performance data taken during the initial tests conducted on the machine. The successful installation and initial operation of the Mod-1 wind turbine generator has had the following results: (1) megawatt-size wind turbines can be operated satisfactorily on utility grids; (2) the structural loads can be predicted by existing codes; (3) assembly of the machine on top of the tower presents no major problem; (4) large blades 100 ft long can be transported long distances and over mountain roads; and (5) operating experience and performance data will contribute substantially to the design of future low-cost wind turbines.

Scrape-off layer reflectometer for Alcator C-Mod.

PubMed

Hanson, G R; Wilgen, J B; Lau, C; Lin, Y; Wallace, G M; Wukitch, S J

2008-10-01

A two-frequency x-mode reflectometer operating from 100 to 146 GHz is deployed on Alcator C-Mod to measure the density profile and fluctuations in the scrape-off layer (SOL) immediately in front of the new J-port ICRF antenna and the new C-port lower hybrid launcher. The reflectometer covers densities from 10(16) to 10(20) m(-3) at 5-5.4 T. To provide the greatest flexibility and capability to deal with density fluctuations approaching 100% peak-to-peak in the SOL, both full-phase and differential-phase measurement capabilities with sweep speeds of approximately 10 micros to >1 ms are implemented. The differential-phase measurement uses a difference frequency of 500 MHz, corresponding to cutoff layer separations ranging from about 0.1 to 1 mm. The reflectometer has six sets of launchers: three on the ICRF antenna and three on the lower hybrid launcher. Both the ICRF antenna and the lower hybrid launcher incorporate reflectometer antennas at their top, bottom, and midplane locations.

Search for Quadrupole Strength in the Electroexcitation of the Delta+ (1232)

DOE Office of Scientific and Technical Information (OSTI.GOV)

C. Mertz; C. Vellidis; Ricardo Alarcon

2001-04-01

High precision 1H(e, e'p)pi0 measurements at Q2 = 0.126. (GeV/c)2 are reported, which allow the determination of quadrupole amplitudes in the gamma*N --> Delta transition; they simultaneously test the reliability of electroproduction models. The derived quadrupole-to-dipole (I = 3/2) amplitude ratios, RSM = (-6.5 +/- 0.2stat+sys+/-2.5mod)% and REM = 9-2.1 +/-0.2stat+sys +/-2.0mod)%, are dominated by model error. Previous RSM and REM results should be reconsidered after the model uncertainties associated with the method of their extraction are taken into account.

Current status of the facility instrumentation suite at the Large Binocular Telescope Observatory

NASA Astrophysics Data System (ADS)

Rothberg, Barry; Kuhn, Olga; Edwards, Michelle L.; Hill, John M.; Thompson, David; Veillet, Christian; Wagner, R. Mark

2016-07-01

The current status of the facility instrumentation for the Large Binocular Telescope (LBT) is reviewed. The LBT encompasses two 8.4 meter primary mirrors on a single mount yielding an effective collecting area of 11.8 meters or 23 meters when interferometrically combined. The three facility instruments at LBT include: 1) the Large Binocular Cameras (LBCs), each with a 23'× 25' field of view (FOV). The blue optimized and red optimized optical wavelength LBCs are mounted at the prime focus of the SX (left) and DX (right) primary mirrors, respectively. Combined, the filter suite of the two LBCs cover 0.3-1.1 μm, including the addition of new medium-band filters centered on TiO (0.78 μm) and CN (0.82 μm) 2) the Multi-Object Double Spectrograph (MODS), two identical optical spectrographs each mounted at the straight through f/15 Gregorian focus of the primary mirrors. The capabilities of MODS-1 and -2 include imaging with Sloan filters (u, g, r, i, and z) and medium resolution (R ˜ 2000) spectroscopy, each with 24 interchangeable masks (multi-object or longslit) over a 6'× 6' FOV. Each MODS is capable of blue (0.32-0.6 μm) and red (0.5-1.05 μm) wavelength only spectroscopy coverage or both can employ a dichroic for 0.32-1.05 μm wavelength coverage (with reduced coverage from 0.56- 0.57 μm) and 3) the two LBT Utility Camera in the Infrared instruments (LUCIs), are each mounted at a bent-front Gregorian f/15 focus of a primary mirror. LUCI-1 and 2 are designed for seeing-limited (4'× 4' FOV) and active optics using thin-shell adaptive secondary mirrors (0.5'× 0.5' FOV) imaging and spectroscopy over the wavelength range of 0.95-2.5 μm and spectroscopic resolutions of 400 <= R <= 11000 (depending on the combination of grating, slits, and cameras used). The spectroscopic capabilities also include 32 interchangeable multi-object or longslit masks which are cryogenically cooled. Currently all facility instruments are in-place at the LBT and, for the first time, have been on-sky for science observations. In Summer 2015 LUCI-1 was refurbished to replace the infrared detector; to install a high-resolution camera to take advantage of the active optics SX secondary; and to install a grating designed primarily for use with high resolution active optics. Thus, like MODS-1 and -2, both LUCIs now have specifications nearly identical to each other. The software interface for both LUCIs have also been replaced, allowing both instruments to be run together from a single interface. With the installation of all facility instruments finally complete we also report on the first science use of "mixed-mode" operations, defined as the combination of different paired instruments with each mirror (i.e. LBC+MODS, LBC+LUCI, LUCI+MODS). Although both primary mirrors reside on a single fixed mount, they are capable of operating as independent entities within a defined "co-pointing" limit. This provides users with the additional capability to independently dither each mirror or center observations on two different sets of spatial coordinates within this limit.

Overview of Recent Alcator C-Mod Highlights

NASA Astrophysics Data System (ADS)

Marmar, Earl; C-Mod Team

2013-10-01

Analysis and modeling of recent C-Mod experiments has yielded significant results across multiple research topics. I-mode provides routine access to high confinement plasma (H98 up to 1.2) in quasi-steady state, without large ELMs; pedestal pressure and impurity transport are regulated by short-wavelength EM waves, and core turbulence is reduced. Multi-channel transport is being investigated in Ohmic and RF-heated plasmas, using advanced diagnostics to validate non-linear gyrokinetic simulations. Results from the new field-aligned ICRF antenna, including significantly reduced high-Z metal impurity contamination, and greatly improved load-tolerance, are being understood through antenna-plasma modeling. Reduced LHCD efficiency at high density correlates with parametric decay and enhanced edge absorption. Strong flow drive and edge turbulence suppression are seen from LHRF, providing new approaches for plasma control. Plasma density profiles directly in front of the LH coupler show non-linear modifications, with important consequences for wave coupling. Disruption-mitigation experiments using massive gas injection at multiple toroidal locations show unexpected results, with potentially significant implications for ITER. First results from a novel accelerator-based PMI diagnostic are presented. What would be the world's first actively-heated high-temperature advanced tungsten divertor is designed and ready for construction. Conceptual designs are being developed for an ultra-advanced divertor facility, Alcator DX, to attack key FNSF and DEMO heat-flux challenges integrated with a high-performance core. Supported by USDOE.

H-mode pedestal stability and ELMs in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Mossessian, Dmitri

2002-11-01

For steady state H-mode operation, a relaxation mechanism is required to limit build-up of the edge gradient and impurity accumulation. The major relaxation mechanism seen on most of the existing tokamaks - large type I ELMs - drive high particle and energy fluxes that present a significant power load on the divertor plates. On Alcator C-Mod, however, type I ELMs are not observed. Instead, more benign mechanisms - EDA and small grassy ELMs - appear to drive enhanced particle transport at the edge of H-mode plasmas. Both have good energy confinement, no impurity accumulation, and are steady state. In EDA the edge relaxation mechanism is provided by a quasicoherent electromagnetic mode localized in the outer part of the pedestal. Non-linear gyrofluid and linear gyrokinetic simulations, as well as real geometry fluctuation modeling based on fluid equations show the presence of a coherent mode. Based on those results the observed mode is tentatively identified as resistive ballooning. At higher edge pressure gradient the mode is replaced by broadband fluctuations and small irregular ELMs are observed. Based on ideal MHD calculations that include effects of bootstrap current, these ELMs are identified as medium n coupled ideal peeling/ballooning modes. The stability threshold and modes structure of these modes are studied with recently developed linear MHD stability code ELITE and the results are compared with the observed dependence of the ELMs' character on pedestal parameters and plasma shape.

The Submillimeter Wave Electron Cyclotron Emission Diagnostic for the Alcator C-Mod Tokamak.

NASA Astrophysics Data System (ADS)

Hsu, Thomas C.

This thesis describes the engineering design, construction, and operation of a high spatial resolution submillimeter wave diagnostic for electron temperature measurements on Alcator C-Mod. Alcator C-Mod is a high performance compact tokamak capable of producing diverted, shaped plasmas with a major radius of 0.67 meters, minor radius of 0.21 centimeters, plasma current of 3 MA. The maximum toroidal field is 9 Tesla on the magnetic axis. The ECE diagnostic includes three primary components: a 10.8 meter quasioptical transmission line, a rapid scanning Michelson interferometer, and a vacuum compatible calibration source. Due to the compact size and high field of the tokamak the ECE system was designed to have a spectral range from 100 to 1000 GHz with frequency resolution of 5 GHz and spatial resolution of one centimeter. The beamline uses all reflecting optical elements including two off-axis parabolic mirrors with diameters of 20 cm. and focal lengths of 2.7 meters. Techniques are presented for grinding and finishing the mirrors to sufficient surface quality to permit optical alignment of the system. Measurements of the surface figure confirm the design goal of 1/4 wavelength accuracy at 1000 GHz. Extensive broadband tests of the spatial resolution of the ECE system are compared to a fundamental mode Gaussian beam model, a three dimensional vector diffraction model, and a geometric optics model. The Michelson interferometer is a rapid scanning polarization instrument which has an apodized frequency resolution of 5 GHz and a minimum scan period of 7.5 milliseconds. The novel features of this instrument include the use of precision linear bearings to stabilize the moving mirror and active counterbalancing to reduce vibration. Beam collimation within the instrument is done with off-axis parabolic mirrors. The Michelson also includes a 2-50 mm variable aperture and two signal attenuators constructed from crossed wire grid polarizers. To make full use of the advantages of an evacuated optical path a dual element in-situ calibration source was designed and constructed. The calibration source operates as a thermal blackbody at temperatures from 77K to 373K and base pressures down to 10^{-7} torr. The top element of the source serves as a room temperature reference while the lower element can be heated or cooled by the circulation of an appropriate fluid through the internal heat transfer tubes. The submillimeter absorbing bodies of both elements are made from arrays of knife edge tiles cast from thermally conductive, alumina filled epoxy. A boundary element heat transfer model of the tiles was constructed which indicates temperature uniformity within 1.5 percent. Operation during the 1993 startup of Alcator C -Mod demonstrates the excellent potential of the new instruments. (Copies available exclusively from MIT Libraries, Rm. 14-0551, Cambridge, MA 02139-4307. Ph. 617-253-5668; Fax 617-253 -1690.) (Abstract shortened by UMI.).

Virtual Habitat -a dynamic simulation of closed life support systems -human model status

NASA Astrophysics Data System (ADS)

Markus Czupalla, M. Sc.; Zhukov, Anton; Hwang, Su-Au; Schnaitmann, Jonas

In order to optimize Life Support Systems on a system level, stability questions must be in-vestigated. To do so the exploration group of the Technical University of Munich (TUM) is developing the "Virtual Habitat" (V-HAB) dynamic LSS simulation software. V-HAB shall provide the possibility to conduct dynamic simulations of entire mission scenarios for any given LSS configuration. The Virtual Habitat simulation tool consists of four main modules: • Closed Environment Module (CEM) -monitoring of compounds in a closed environment • Crew Module (CM) -dynamic human simulation • P/C Systems Module (PCSM) -dynamic P/C subsystems • Plant Module (PM) -dynamic plant simulation The core module of the simulation is the dynamic and environment sensitive human module. Introduced in its basic version in 2008, the human module has been significantly updated since, increasing its capabilities and maturity significantly. In this paper three newly added human model subsystems (thermal regulation, digestion and schedule controller) are introduced touching also on the human stress subsystem which is cur-rently under development. Upon the introduction of these new subsystems, the integration of these into the overall V-HAB human model is discussed, highlighting the impact on the most important I/F. The overall human model capabilities shall further be summarized and presented based on meaningful test cases. In addition to the presentation of the results, the correlation strategy for the Virtual Habitat human model shall be introduced assessing the models current confidence level and giving an outlook on the future correlation strategy. Last but not least, the remaining V-HAB mod-ules shall be introduced shortly showing how the human model is integrated into the overall simulation.

Quantitative comparison of electron temperature fluctuations to nonlinear gyrokinetic simulations in C-Mod Ohmic L-mode discharges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sung, C., E-mail: csung@physics.ucla.edu; White, A. E.; Greenwald, M.

2016-04-15

Long wavelength turbulent electron temperature fluctuations (k{sub y}ρ{sub s} < 0.3) are measured in the outer core region (r/a > 0.8) of Ohmic L-mode plasmas at Alcator C-Mod [E. S. Marmar et al., Nucl. Fusion 49, 104014 (2009)] with a correlation electron cyclotron emission diagnostic. The relative amplitude and frequency spectrum of the fluctuations are compared quantitatively with nonlinear gyrokinetic simulations using the GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] in two different confinement regimes: linear Ohmic confinement (LOC) regime and saturated Ohmic confinement (SOC) regime. When comparing experiment with nonlinear simulations, it is found that local,more » electrostatic ion-scale simulations (k{sub y}ρ{sub s} ≲ 1.7) performed at r/a ∼ 0.85 reproduce the experimental ion heat flux levels, electron temperature fluctuation levels, and frequency spectra within experimental error bars. In contrast, the electron heat flux is robustly under-predicted and cannot be recovered by using scans of the simulation inputs within error bars or by using global simulations. If both the ion heat flux and the measured temperature fluctuations are attributed predominantly to long-wavelength turbulence, then under-prediction of electron heat flux strongly suggests that electron scale turbulence is important for transport in C-Mod Ohmic L-mode discharges. In addition, no evidence is found from linear or nonlinear simulations for a clear transition from trapped electron mode to ion temperature gradient turbulence across the LOC/SOC transition, and also there is no evidence in these Ohmic L-mode plasmas of the “Transport Shortfall” [C. Holland et al., Phys. Plasmas 16, 052301 (2009)].« less

Correlation of the expression of YY1 and Fas cell surface death receptor with apoptosis of peripheral blood mononuclear cells, and the development of multiple organ dysfunction in children with sepsis.

PubMed

Reséndiz-Martínez, Judith; Asbun-Bojalil, Juan; Huerta-Yepez, Sara; Vega, Mario

2017-05-01

Multiple organ dysfunction (MOD) is a lethal complication in children with sepsis. Apoptosis of several cell types is involved in this process, and it is associated with increased Fas cell surface death receptor (Fas) expression. As YY1 transcription factor (YY1) negatively regulates the expression of Fas in cancer models, and is associated with the clinical outcome, it may be important in MOD. The present study aimed to determine the association between the expression of Fas, YY1 and apoptosis in children with sepsis, and its association with MOD, these factors were analyzed in 30 pediatric patients that had been diagnosed with sepsis. Peripheral blood mononuclear cells were purified from patients, and YY1 and Fas protein expression was assessed by immunocytochemistry. Apoptosis was determined by terminal deoxynucleotidyl transferase dUTP nick‑end labeling. Sepsis was monitored using clinical parameters, pediatric logistic organ dysfunction (PELOD) score and the pediatric mortality index. The results demonstrated that Fas expression was directly correlated with apoptosis levels and the expression of YY1 was inversely correlated with apoptosis levels. Patients with high levels of apoptosis exhibited increased disease severity and poor clinical outcome. Notably, the findings of the present study demonstrated that there were higher survival rates in patients with high YY1 expression, compared with those with low YY1 expression. Additionally, patients with MOD exhibited lower proportions of apoptotic cells compared with sepsis patients without MOD. Furthermore, the PELOD score was positively correlated with Fas and inversely correlated with YY1 expression. Finally, high apoptosis and low YY1 expression were prognostic factors associated with poor survival rates. These data suggested that YY1 may be important for apoptosis induction via the regulation of Fas during sepsis. Therefore, Fas may be a potential therapeutic target to prevent MOD through regulation of YY1 expression. Furthermore, YY1 and Fas expression in PBMCs may be used to as prognostic markers.

Correlation of the expression of YY1 and Fas cell surface death receptor with apoptosis of peripheral blood mononuclear cells, and the development of multiple organ dysfunction in children with sepsis

PubMed Central

Reséndiz-Martínez, Judith; Asbun-Bojalil, Juan; Huerta-Yepez, Sara; Vega, Mario

2017-01-01

Multiple organ dysfunction (MOD) is a lethal complication in children with sepsis. Apoptosis of several cell types is involved in this process, and it is associated with increased Fas cell surface death receptor (Fas) expression. As YY1 transcription factor (YY1) negatively regulates the expression of Fas in cancer models, and is associated with the clinical outcome, it may be important in MOD. The present study aimed to determine the association between the expression of Fas, YY1 and apoptosis in children with sepsis, and its association with MOD, these factors were analyzed in 30 pediatric patients that had been diagnosed with sepsis. Peripheral blood mononuclear cells were purified from patients, and YY1 and Fas protein expression was assessed by immunocytochemistry. Apoptosis was determined by terminal deoxynucleotidyl transferase dUTP nick-end labeling. Sepsis was monitored using clinical parameters, pediatric logistic organ dysfunction (PELOD) score and the pediatric mortality index. The results demonstrated that Fas expression was directly correlated with apoptosis levels and the expression of YY1 was inversely correlated with apoptosis levels. Patients with high levels of apoptosis exhibited increased disease severity and poor clinical outcome. Notably, the findings of the present study demonstrated that there were higher survival rates in patients with high YY1 expression, compared with those with low YY1 expression. Additionally, patients with MOD exhibited lower proportions of apoptotic cells compared with sepsis patients without MOD. Furthermore, the PELOD score was positively correlated with Fas and inversely correlated with YY1 expression. Finally, high apoptosis and low YY1 expression were prognostic factors associated with poor survival rates. These data suggested that YY1 may be important for apoptosis induction via the regulation of Fas during sepsis. Therefore, Fas may be a potential therapeutic target to prevent MOD through regulation of YY1 expression. Furthermore, YY1 and Fas expression in PBMCs may be used to as prognostic markers. PMID:28447715

Mod-1 Wind Turbine at Boone, North Carolina

NASA Image and Video Library

1979-06-21

A Mod-1 2000-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Boone, North Carolina. The wind turbine program was a joint program between NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed at NASA’s Plum Brook Station. There were four Mod-0A 200-kilowatt turbines built in New Mexico, Hawaii, Puerto Rico, and Rhode Island. The 2000-kilowatt wind turbine in North Carolina, seen here, was the only Mod-1 machine constructed. The two-bladed, 200-foot diameter device was built in May 1979 and began operation that September. The Mod-1 turbine performed exceedingly well and was fully integrated into the local power grid. NASA researchers also used the North Carolina device to study its effect on noise and television transmission.

Acute management and outcome of multiple trauma patients with pelvic disruptions

PubMed Central

2012-01-01

Introduction Data on prehospital and trauma-room fluid management of multiple trauma patients with pelvic disruptions are rarely reported. Present trauma algorithms recommend early hemorrhage control and massive fluid resuscitation. By matching the German Pelvic Injury Register (PIR) with the TraumaRegister DGU (TR) for the first time, we attempt to assess the initial fluid management for different Tile/OTA types of pelvic-ring fractures. Special attention was given to the patient's posttraumatic course, particularly intensive care unit (ICU) data and patient outcome. Methods A specific match code was applied to identify certain patients with pelvic disruptions from both PIR and TR anonymous trauma databases, admitted between 2004 and 2009. From the resulting intersection set, a retrospective analysis was done of prehospital and trauma-room data, length of ICU stay, days of ventilation, incidence of multiple organ dysfunction syndrome (MODS), sepsis, and mortality. Results In total, 402 patients were identified. Mean ISS was 25.9 points, and the mean of patients with ISS ≥16 was 85.6%. The fracture distribution was as follows: 19.7% type A, 29.4% type B, 36.6% type C, and 14.3% isolated acetabular and/or sacrum fractures. The type B/C, compared with type A fractures, were related to constantly worse vital signs that necessitated a higher volume of fluid and blood administration in the prehospital and/or the trauma-room setting. This group of B/C fractures were also related to a significantly higher presence of concomitant injuries and related to increased ISS. This was related to increased ventilation and ICU stay, increased rate of MODS, sepsis, and increased rate of mortality, at least for the type C fractures. Approximately 80% of the dead had sustained type B/C fractures. Conclusions The present study confirms the actuality of traditional trauma algorithms with initial massive fluid resuscitation in the recent therapy of multiple trauma patients with pelvic disruptions. Low-volume resuscitation seems not yet to be accepted in practice in managing this special patient entity. Mechanically unstable pelvic-ring fractures type B/C (according to the Tile/OTA classification) form a distinct entity that must be considered notably in future trauma algorithms. PMID:22913820

46 CFR 160.023-1 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Combination Flare and Smoke Distress Signals § 160.023-1... specifications MIL-S-18655 C, 3 May 1971—Signal, Smoke and Illumination, Marine, Mark 13, Mod 0. (b) The military...

46 CFR 160.023-1 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Combination Flare and Smoke Distress Signals § 160.023-1... specifications MIL-S-18655 C, 3 May 1971—Signal, Smoke and Illumination, Marine, Mark 13, Mod 0. (b) The military...

46 CFR 160.023-1 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Combination Flare and Smoke Distress Signals § 160.023-1... specifications MIL-S-18655 C, 3 May 1971—Signal, Smoke and Illumination, Marine, Mark 13, Mod 0. (b) The military...

46 CFR 160.023-1 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Combination Flare and Smoke Distress Signals § 160.023-1... specifications MIL-S-18655 C, 3 May 1971—Signal, Smoke and Illumination, Marine, Mark 13, Mod 0. (b) The military...

Linear servomotor probe drive system with real-time self-adaptive position control for the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, D.; Kuang, A. Q.; LaBombard, B.; Burke, W.

2017-07-01

A new servomotor drive system has been developed for the horizontal reciprocating probe on the Alcator C-Mod tokamak. Real-time measurements of plasma temperature and density—through use of a mirror Langmuir probe bias system—combined with a commercial linear servomotor and controller enable self-adaptive position control. Probe surface temperature and its rate of change are computed in real time and used to control probe insertion depth. It is found that a universal trigger threshold can be defined in terms of these two parameters; if the probe is triggered to retract when crossing the trigger threshold, it will reach the same ultimate surface temperature, independent of velocity, acceleration, or scrape-off layer heat flux scale length. In addition to controlling the probe motion, the controller is used to monitor and control all aspects of the integrated probe drive system.

Modification of ordinary-mode reflectometry system to detect lower-hybrid waves in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baek, S. G.; Shiraiwa, S.; Parker, R. R.

2012-10-15

Backscattering experiments to detect lower-hybrid (LH) waves have been performed in Alcator C-Mod, using the two modified channels (60 GHz and 75 GHz) of an ordinary-mode reflectometry system with newly developed spectral recorders that can continuously monitor spectral power at a target frequency. The change in the baseline of the spectral recorder during the LH wave injection is highly correlated to the strength of the X-mode non-thermal electron cyclotron emission. In high density plasmas where an anomalous drop in the lower hybrid current drive efficiency is observed, the observed backscattered signals are expected to be generated near the last closedmore » flux surface, demonstrating the presence of LH waves within the plasma. This experimental technique can be useful in identifying spatially localized LH electric fields in the periphery of high-density plasmas.« less

Influence of ICRF heating on the stability of TAEs

NASA Astrophysics Data System (ADS)

Sears, J.; Burke, W.; Parker, R. R.; Snipes, J. A.; Wolfe, S.

2007-11-01

Unstable toroidicity-induced Alfv'en eigenmodes (TAEs) can appear spontaneously due to resonant interaction with fast particles such as fusion alphas, raising concern that TAEs may threaten ITER performance. This work investigates the progression of stable TAE damping rates toward instability during a scan of ICRF heating power up to 3.1 MW. Stable eigenmodes are identified in Alcator C-Mod by the Active MHD diagnostic. Unstable TAEs are observed to appear spontaneously in C-Mod limited L-mode plasmas at sufficient tail energies generated by >3 MW of ICRF heating. However preliminary analysis of experiments with moderate ICRF heating power show that TAE stability may not simply degrade with overall fast particle content. There are hints that the stability of some TAEs may be enhanced in the presence of fast particle distribution tails. Furthermore, the radial profile of the energetic particle distribution relative to the safety factor profile affects the ICRF power influence on TAE stability.

High speed movies of turbulence in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terry, J.L.; Zweben, S.J.; Bose, B.

2004-10-01

A high speed (250 kHz), 300 frame charge coupled device camera has been used to image turbulence in the Alcator C-Mod Tokamak. The camera system is described and some of its important characteristics are measured, including time response and uniformity over the field-of-view. The diagnostic has been used in two applications. One uses gas-puff imaging to illuminate the turbulence in the edge/scrape-off-layer region, where D{sub 2} gas puffs localize the emission in a plane perpendicular to the magnetic field when viewed by the camera system. The dynamics of the underlying turbulence around and outside the separatrix are detected in thismore » manner. In a second diagnostic application, the light from an injected, ablating, high speed Li pellet is observed radially from the outer midplane, and fast poloidal motion of toroidal striations are seen in the Li{sup +} light well inside the separatrix.« less

Improved Controls for Fusion RF Systems. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casey, Jeffrey A.

2011-11-08

We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way thatmore » they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.« less

Mod 1 ICS TI Report: ICS Conversion of a 140% HPGe Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bounds, John Alan

This report evaluates the Mod 1 ICS, an electrically cooled 140% HPGe detector. It is a custom version of the ORTEC Integrated Cooling System (ICS) modified to make it more practical for us to use in the field. Performance and operating characteristics of the Mod 1 ICS are documented, noting both pros and cons. The Mod 1 ICS is deemed a success. Recommendations for a Mod 2 ICS, a true field prototype, are provided.

ModFOLD6: an accurate web server for the global and local quality estimation of 3D protein models.

PubMed

Maghrabi, Ali H A; McGuffin, Liam J

2017-07-03

Methods that reliably estimate the likely similarity between the predicted and native structures of proteins have become essential for driving the acceptance and adoption of three-dimensional protein models by life scientists. ModFOLD6 is the latest version of our leading resource for Estimates of Model Accuracy (EMA), which uses a pioneering hybrid quasi-single model approach. The ModFOLD6 server integrates scores from three pure-single model methods and three quasi-single model methods using a neural network to estimate local quality scores. Additionally, the server provides three options for producing global score estimates, depending on the requirements of the user: (i) ModFOLD6_rank, which is optimized for ranking/selection, (ii) ModFOLD6_cor, which is optimized for correlations of predicted and observed scores and (iii) ModFOLD6 global for balanced performance. The ModFOLD6 methods rank among the top few for EMA, according to independent blind testing by the CASP12 assessors. The ModFOLD6 server is also continuously automatically evaluated as part of the CAMEO project, where significant performance gains have been observed compared to our previous server and other publicly available servers. The ModFOLD6 server is freely available at: http://www.reading.ac.uk/bioinf/ModFOLD/. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Navy Energy Forum - Seapower Repowered: Energy as a Force Multiplier and Strategic Resource

DTIC Science & Technology

2010-10-13

Energy Harvesting Online GT Water Wash Energy Dashboard Air Film Hull Drag Reduction GTG Efficiency Improvements Propulsion Mods Combustion Trim Loop...States cost of military force projection in the Persian Gulf, 1976–2007, Energy Policy, 2010. 1980’s nowCountries in gray export oil to the U.S...Period 10yr ROI Status/Notes Online Gas Turbine Waterwash for GTM and GTG (Ships) ~ 800 bbls / $136K Per ship per year

Phase Evolution of YBa2Cu3O7-x films by all-chemical solution deposition route for coated conductors

NASA Astrophysics Data System (ADS)

Zhao, Yue; Tang, Xiao; Wu, Wei; Grivel, Jean-Claude

2014-05-01

In order to understand the all-chemical-solution-deposition (CSD) processes for manufacturing coated conductors, we investigated the phase evolution of YBa2Cu3O7 (YBCO) films deposited by a low-fluorine metal-organic solution deposition (LF-MOD) method on CSD derived Ce0.9La0.1O2/Gd2Zr2O7/NiW. It is shown that the phase transition from the pyrolyzed film to fully converted YBCO film in the LF-MOD process is similar to that in typical trifluoroacetates-metal organic deposition (TFA-MOD) processes even though the amount of TFA in the solution is reduced by almost one half compared with typical TFA-MOD cases. Moreover, we found that the formation of impurities (mainly BaCeO3, NiWO4 and NiO) is strongly related to the annealing temperature, i.e., the diffusion controlled reactions become intensive from 760 oC, which might be connected with the poor structural and superconducting properties of the films deposited at high sintering temperatures. Based on these results, the optimized growth conditions of YBCO films were established, and a high critical current density (Jc) of about 2 MA/cm2 (77 K, self field) is achieved in a 200 nm thick YBCO film in the architecture made by our all CSD route.

Magnetic resonance imaging correlates of bee sting induced multiple organ dysfunction syndrome: A case report.

PubMed

Das, Sushant K; Zeng, Li-Chuan; Li, Bing; Niu, Xiang-Ke; Wang, Jing-Liang; Bhetuwal, Anup; Yang, Han-Feng

2014-09-28

Occasionally systemic complications with high risk of death, such as multiple organ dysfunction syndrome (MODS), can occur following multiple bee stings. This case study reports a patient who presented with MODS, i.e., acute kidney injury, hepatic and cardiac dysfunction, after multiple bee stings. The standard clinical findings were then correlated with magnetic resonance imaging (MRI) findings, which demonstrates that MRI may be utilized as a simpler tool to use than other multiple diagnostics.

Modafinil Activates Phasic Dopamine Signaling in Dorsal and Ventral Striata

PubMed Central

Bobak, Martin J.; Weber, Matthew W.; Doellman, Melissa A.; Schuweiler, Douglas R.; Athens, Jeana M.; Juliano, Steven A.

2016-01-01

Modafinil (MOD) exhibits therapeutic efficacy for treating sleep and psychiatric disorders; however, its mechanism is not completely understood. Compared with other psychostimulants inhibiting dopamine (DA) uptake, MOD weakly interacts with the dopamine transporter (DAT) and modestly elevates striatal dialysate DA, suggesting additional targets besides DAT. However, the ability of MOD to induce wakefulness is abolished with DAT knockout, conversely suggesting that DAT is necessary for MOD action. Another psychostimulant target, but one not established for MOD, is activation of phasic DA signaling. This communication mode during which burst firing of DA neurons generates rapid changes in extracellular DA, the so-called DA transients, is critically implicated in reward learning. Here, we investigate MOD effects on phasic DA signaling in the striatum of urethane-anesthetized rats with fast-scan cyclic voltammetry. We found that MOD (30–300 mg/kg i.p.) robustly increases the amplitude of electrically evoked phasic-like DA signals in a time- and dose-dependent fashion, with greater effects in dorsal versus ventral striata. MOD-induced enhancement of these electrically evoked amplitudes was mediated preferentially by increased DA release compared with decreased DA uptake. Principal component regression of nonelectrically evoked recordings revealed negligible changes in basal DA with high-dose MOD (300 mg/kg i.p.). Finally, in the presence of the D2 DA antagonist, raclopride, low-dose MOD (30 mg/kg i.p.) robustly elicited DA transients in dorsal and ventral striata. Taken together, these results suggest that activation of phasic DA signaling is an important mechanism underlying the clinical efficacy of MOD. PMID:27733628

Mechanical behavior of bulk direct composite versus block composite and lithium disilicate indirect Class II restorations by CAD-FEM modeling.

PubMed

Ausiello, Pietro; Ciaramella, Stefano; Fabianelli, Andrea; Gloria, Antonio; Martorelli, Massimo; Lanzotti, Antonio; Watts, David C

2017-06-01

To study the influence of resin based and lithium disilicate materials on the stress and strain distributions in adhesive class II mesio-occlusal-distal (MOD) restorations using numerical finite element analysis (FEA). To investigate the materials combinations in the restored teeth during mastication and their ability to relieve stresses. One 3D model of a sound lower molar and three 3D class II MOD cavity models with 95° cavity-margin-angle shapes were modelled. Different material combinations were simulated: model A, with a 10μm thick resin bonding layer and a resin composite bulk filling material; model B, with a 70μm resin cement with an indirect CAD-CAM resin composite inlay; model C, with a 70μm thick resin cement with an indirect lithium disilicate machinable inlay. To simulate polymerization shrinkage effects in the adhesive layers and bulk fill composite, the thermal expansion approach was used. Shell elements were employed for representing the adhesive layers. 3D solid CTETRA elements with four grid points were employed for modelling the food bolus and tooth. Slide-type contact elements were used between the tooth surface and food. A vertical occlusal load of 600 N was applied, and nodal displacements on the bottom cutting surfaces were constrained in all directions. All the materials were assumed to be isotropic and elastic and a static linear analysis was performed. Displacements were different in models A, B and C. Polymerization shrinkage hardly affected model A and mastication only partially affected mechanical behavior. Shrinkage stress peaks were mainly located marginally along the enamel-restoration interface at occlusal and mesio-distal sites. However, at the internal dentinal walls, stress distributions were critical with the highest maximum stresses concentrated in the proximal boxes. In models B and C, shrinkage stress was only produced by the 70μm thick resin layer, but the magnitudes depended on the Young's modulus (E) of the inlay materials. Model B mastication behavior (with E=20GPa) was similar to the sound tooth stress relief pattern. Model B internally showed differences from the sound tooth model but reduced maximum stresses than model A and partially than model C. Model C (with E=70GPa) behaved similarly to model B with well redistributed stresses at the occlusal margins and the lateral sides with higher stress concentrations in the proximal boxes. Models B and C showed a more favorable performance than model A with elastic biomechanics similar to the sound tooth model. Bulk filling resin composite with 1% linear polymerization shrinkage negatively affected the mechanical behavior of class II MOD restored teeth. Class II MOD direct resin composite showed greater potential for damage because of higher internal and marginal stress evolution during resin polymerization shrinkage. With a large class II MOD cavity an indirect composite or a lithium disilicate inlay restoration may provide a mechanical response close to that of a sound tooth. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Background and system description of the Mod 1 wind turbine generator

NASA Technical Reports Server (NTRS)

Ernst, E. H.

1978-01-01

The Mod-1 wind turbine considered is a large utility-class machine, operating in the high wind regime, which has the potential for generation of utility grade power at costs competitive with other alternative energy sources. A Mod-1 wind turbine generator (WTG) description is presented, taking into account the two variable-pitch steel blades of the rotor, the drive train, power generation/control, the Nacelle structure, and the yaw drive. The major surface elements of the WTG are the ground enclosure, the back-up battery system, the step-up transformer, elements of the data system, cabling, area lighting, and tower foundation. The final system weight (rotor, Nacelle, and tower) is expected to be about 650,000 pounds. The WTG will be capable of delivering 1800 kW to the utility grid in a wind-speed above 25 mph.

On the correlation between ‘non-local’ effects and intrinsic rotation reversals in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Rodriguez-Fernandez, P.; Rice, J. E.; Cao, N. M.; Creely, A. J.; Howard, N. T.; Hubbard, A. E.; Irby, J. H.; White, A. E.

2017-07-01

Contemporary predictive models for heat and particle transport in tokamak plasmas are based on the assumption that local fluxes can be described in terms of local plasma parameters, where electromagnetic drift-wave-type turbulence is driven by local gradients and results in cross-field transport. The question of whether or not transport could be dominated by non-local terms in certain circumstances is essential for our understanding of transport in magnetically confined plasmas, and critical for developing predictive models for future tokamaks, such as ITER. Perturbative transport experiments using cold-pulse injections at low density seem to challenge the local closure of anomalous transport: a rapid temperature increase in the core of the plasma following a sharp edge cooling is widely observed in tokamaks and helical devices. Past work in Ohmic plasmas in Alcator C-Mod and in ECH plasmas in KSTAR found that the temperature inversions disappear at higher densities, above the intrinsic toroidal rotation reversal density. These observations suggested that the so-called ‘non-local’ heat transport effects were related to the intrinsic rotation reversal, and therefore to changes in momentum transport. In this work, new experiments and analysis at Alcator C-Mod show that intrinsic rotation reversals and disappearance of temperature inversions are not concomitant in Ohmic plasmas at high plasma current and in ICRH L-modes. This new data set shows that the correlation between transient temperature inversions and intrinsic rotation reversals is not universal, suggesting that ‘non-local’ heat transport and momentum transport effects may be affected by different physical mechanisms.

Helium experiments on Alcator C-Mod in support of ITER early operations

DOE PAGES

Kessel, C. E.; Wolfe, S. M.; Reinke, M. L.; ...

2018-03-13

Helium majority experiments on Alcator C-Mod were performed to compare with deuterium discharges, and inform ITER early operations. ELMy H-modes were produced with a special plasma shape at B T = 5.3 T, I P = 0.9 MA, at q 95 ~ 3.8. The He fraction ranged over, n He,L/n L = 0.2–0.4, with n D,L/n L = 0.15–0.26, compared to D plasmas with n D,L/n L = 0.85–0.97. The power to enter the H-mode in He was found to be greater than ~2 times that for D discharges, in the low density region <1.4 × 10 20/m 3. However, it appears to follow the D threshold for higher densities. The stored energies in the He discharges were about 80% of those in D, and about 40% higher net power was required to sustain them compared to D. Global particle confinement times for tungsten ofmore » $$\\tau _{{\\rm W}}^{{\\rm *}}$$ /τ E ~ 4 were obtained with ELMy H-modes in He, however accumulation occurred when the ELMs were irregular and infrequent. The electron temperatures and densities in the pedestal were similar between D and He discharges, and the ΔT e/T e and Δn e/n e values were similar or larger in He than D. The higher net power required to access the H-mode, and sustain it in flattop, for He discharges in C-Mod, imply some limitations for He operation in ITER.« less

Helium experiments on Alcator C-Mod in support of ITER early operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kessel, C. E.; Wolfe, S. M.; Reinke, M. L.

Helium majority experiments on Alcator C-Mod were performed to compare with deuterium discharges, and inform ITER early operations. ELMy H-modes were produced with a special plasma shape at B T = 5.3 T, I P = 0.9 MA, at q 95 ~ 3.8. The He fraction ranged over, n He,L/n L = 0.2–0.4, with n D,L/n L = 0.15–0.26, compared to D plasmas with n D,L/n L = 0.85–0.97. The power to enter the H-mode in He was found to be greater than ~2 times that for D discharges, in the low density region <1.4 × 10 20/m 3. However, it appears to follow the D threshold for higher densities. The stored energies in the He discharges were about 80% of those in D, and about 40% higher net power was required to sustain them compared to D. Global particle confinement times for tungsten ofmore » $$\\tau _{{\\rm W}}^{{\\rm *}}$$ /τ E ~ 4 were obtained with ELMy H-modes in He, however accumulation occurred when the ELMs were irregular and infrequent. The electron temperatures and densities in the pedestal were similar between D and He discharges, and the ΔT e/T e and Δn e/n e values were similar or larger in He than D. The higher net power required to access the H-mode, and sustain it in flattop, for He discharges in C-Mod, imply some limitations for He operation in ITER.« less

A new fast two-color interferometer at Alcator C-Mod for turbulence measurements and comparison with phase contrast imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kasten, C. P., E-mail: ckasten@alum.mit.edu; White, A. E.; Irby, J. H.

2014-04-15

Accurately predicting the turbulent transport properties of magnetically confined plasmas is a major challenge of fusion energy research. Validation of transport models is typically done by applying so-called “synthetic diagnostics” to the output of nonlinear gyrokinetic simulations, and the results are compared to experimental data. As part of the validation process, comparing two independent turbulence measurements to each other provides the opportunity to test the synthetic diagnostics themselves; a step which is rarely possible due to limited availability of redundant fluctuation measurements on magnetic confinement experiments. At Alcator C-Mod, phase-contrast imaging (PCI) is a commonly used turbulence diagnostic. PCI measuresmore » line-integrated electron density fluctuations with high sensitivity and wavenumber resolution (1.6 cm{sup −1}≲|k{sub R}|≲11 cm{sup −1}). A new fast two-color interferometry (FTCI) diagnostic on the Alcator C-Mod tokamak measures long-wavelength (|k{sub R}|≲3.0 cm{sup −1}) line-integrated electron density fluctuations. Measurements of coherent and broadband fluctuations made by PCI and FTCI are compared here for the first time. Good quantitative agreement is found between the two measurements. This provides experimental validation of the low-wavenumber region of the PCI calibration, and also helps validate the low-wavenumber portions of the synthetic PCI diagnostic that has been used in gyrokinetic model validation work in the past. We discuss possibilities to upgrade FTCI, so that a similar comparison could be done at higher wavenumbers in the future.« less

Self-reduction of a copper complex MOD ink for inkjet printing conductive patterns on plastics.

PubMed

Farraj, Yousef; Grouchko, Michael; Magdassi, Shlomo

2015-01-31

Highly conductive copper patterns on low-cost flexible substrates are obtained by inkjet printing a metal complex based ink. Upon heating the ink, the soluble complex, which is composed of copper formate and 2-amino-2-methyl-1-propanol, decomposes under nitrogen at 140 °C and is converted to pure metallic copper. The decomposition process of the complex is investigated and a suggested mechanism is presented. The ink is stable in air for prolonged periods, with no sedimentation or oxidation problems, which are usually encountered in copper nanoparticle based inks.

Helical flow in RFX-mod tokamak plasmas

NASA Astrophysics Data System (ADS)

Piron, L.; Zaniol, B.; Bonfiglio, D.; Carraro, L.; Kirk, A.; Marrelli, L.; Martin, R.; Piron, C.; Piovesan, P.; Zuin, M.

2017-05-01

This work presents the first evidence of helical flow in RFX-mod q(a)  <  2 tokamak plasmas. The flow pattern is characterized by the presence of convective cells with m  =  1 and n  =  1 periodicity in the poloidal and toroidal directions, respectively. A similar helical flow deformation has been observed in the same device when operated as a reversed field pinch (RFP). In RFP plasmas, the flow dynamic is tailored by the innermost resonant m  =  1, n  =  7 tearing mode, which sustains the magnetic field configuration through the dynamo mechanism (Bonomo et al 2011 Nucl. Fusion 51 123007). By contrast, in the tokamak experiments presented here, it is strongly correlated with the m  =  1, n  =  1 MHD activity. A helical deformation of the flow pattern, associated with the deformation of the magnetic flux surfaces, is predicted by several codes, such as Specyl (Bonfiglio et al 2005 Phys. Rev. Lett. 94 145001), PIXIE3D (Chacón et al 2008 Phys. Plasmas 15 056103), NIMROD (King et al 2012 Phys. Plasmas 19 055905) and M3D-C1 (Jardin et al 2015 Phys. Rev. Lett. 115 215001). Among them, the 3D fully non-linear PIXIE3D has been used to calculate synthetic flow measurements, using a 2D flow modelling code. Inputs to the code are the PIXIE3D flow maps, the ion emission profiles as calculated by a 1D collisional radiative impurity transport code (Carraro et al 2000 Plasma Phys. Control. Fusion 42 731) and a synthetic diagnostic with the same geometry installed in RFX-mod. Good agreement between the synthetic and the experimental flow behaviour has been obtained, confirming that the flow oscillations observed with the associated convective cells are a signature of helical flow.

Monocytes, endoplasmic reticulum stress and metabolomics in dogs with multiple organ dysfunction syndrome treated by continuous venovenous hemodiafiltration

PubMed Central

Xu, Yun-Peng; Sui, Xiao-Lu; Zhang, Ai-Sha; Ye, Lei; Gu, Feng-Juan; Chen, Ji-Hong

2017-01-01

Objectives We tried to investigate the mechanism of continuous venovenous hemodiafiltration (CVVHDF) treatment in monocytes function, endoplasmic reticulum (ER) stress signaling pathways, metabolomics and histopathological changes of MODS dogs, and aimed to enhance the understanding of pathogenesis and provide novel avenues to potential therapies. Methods 12 male Beagle dogs were used to develop the stable models of MODS by using hemorrhagic shock plus resuscitation and endotoxemia, and assigned randomly to CVVHDF group (n=6) and MODS group (n=6). The dogs in CVVHDF group were given the typical CVVHDF treatment for 24h after the completion of endotoxin intravenous infusion, while those in MODS group were offered the i.v heparin instead only. Serum sample were collected at five time points, i.e. before anesthesia, 0h, 6h, 12h and 24h after the endotoxin injection (T1˜T5, respectively), and meanwhile, the changes of mRNA, protein and human umbilical vein endothelial cells (HUVECs) apoptosis rates in JNK, CHOP and Caspase-12 were observed before and after interfered by RNA interference technology. Results The levels of DLA-DR, IL-1β and IL-4 were higher than those in MODS group after the CVVHDF treatment, and the early and late apoptosis rates showed downward trend compared with MODS group. In vitro and prior to RNA interference (RNAi), the levels of mRNA and protein expression and HUVECs apoptosis rates of JNK, CHOP and Caspase-12 in CVVHDF group were significantly lower compared to T1 and MODS group respectively. However, the levels of mRNA and protein expression and HUVECs apoptosis rates were significantly lower than those before interfered by RNAi in both two groups. The serum levels of LPCs, ornithine, proline, methionine, etc. were down-regulated while carnitines, FFAs, PC, etc. were increased significantly in MODS (T4), and the serum levels of methionine, proline, arginine and lysine were increased while carnitine, LPCs, PCs, SMs and orthophosporic acid were decreased after 12 hours CVVHDF treatment (T4). Conclusion CVVHDF treatment could reduce the apoptosis of the cells by enhancing the antigen presentation, improving the anti-inflammatory and proinflammatory imbalance and even correcting the metabolic disorder of amino acids and phospholipids. PMID:28380442

Construction of a Mod-0A Wind Turbine in Clayton, New Mexico

NASA Image and Video Library

1977-11-21

TA Mod-0A 200-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Clayton, New Mexico. The wind turbine program was a joint effort by NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed built at NASA’s Plum Brook Station. This Mod-0A 200-kilowatt turbine built in Clayton in 1977 was the program’s second device. It included a 125-foot long blade atop a 100-foot tall tower. The Mod-0A was designed to determine the turbine’s operating problems, integrate the system with the local utilities, and assess the attitude of the local community. There were additional Mod-0A turbines built in Culebra, Puerto Rico; Block Island, Rhode Island; and Oahu, Hawaii. The Mod-0A turbines were initially unreliable and suffered issues with the durability of the rotor blade. Lewis engineers addressed the problems, and the wind turbines proved to be reliable and efficient devices that operated for a number of years. The information gained from these early models was vital to the design and improvement of the later generations.

Effects of different titanium zirconium implant surfaces on initial supragingival plaque formation.

PubMed

John, Gordon; Becker, Jürgen; Schwarz, Frank

2017-07-01

The aim of the current study was the evaluation of biofilm development on different implant surfaces. Initial biofilm formation was investigated on five different implant surfaces, machined titanium (MTi), modified machined acid-etched titanium (modMATi), machined titanium zirconium (MTiZr), modified machined and acid-etched titanium zirconium (modMATiZr) and sandblasted large grid and acid-etched titanium zirconium surface (SLATiZr) for 24 and 48 h. Biocompatibility was tested after tooth brushing of the samples via cell viability testing with human gingival fibroblasts. After 24 h of biofilm collection, mean plaque surface was detected in the following descending order: After 24 h: MTiZr > MTi > SLATiZr > modMATiZr > modMATi. Both M surfaces showed significant higher biofilm formation than the other groups. After 48 h: MTiZr > MTi > SLATiZr > modMATiZr > modMATi. After tooth brushing: SLATiZr > modMATi > modMATiZr > MTi > MTiZr. All native samples depicted significant higher cell viability than their corresponding surfaces after biofilm removal procedure. The TiZr groups especially the modMATiZr group showed slower and less biofilm formation. In combination with the good biocompatibility, both modMA surfaces seem to be interesting candidates for surfaces in transgingival implant design. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Mod3DMT and EMTF: Free Software for MT Data Processing and Inversion

NASA Astrophysics Data System (ADS)

Egbert, G. D.; Kelbert, A.; Meqbel, N. M.

2017-12-01

"ModEM" was developed at Oregon State University as a modular system for inversion of electromagnetic (EM) geophysical data (Egbert and Kelbert, 2012; Kelbert et al., 2014). Although designed for more general (frequency domain) EM applications, and originally intended as a testbed for exploring inversion search and regularization strategies, our own initial uses of ModEM were for 3-D imaging of the deep crust and upper mantle at large scales. Since 2013 we have offered a version of the source code suitable for 3D magnetotelluric (MT) inversion on an "as is, user beware" basis for free for non-commercial applications. This version, which we refer to as Mod3DMT, has since been widely used by the international MT community. Over 250 users have registered to download the source code, and at least 50 MT studies in the refereed literature, covering locations around the globe at a range of spatial scales, cite use of ModEM for 3D inversion. For over 30 years I have also made MT processing software available for free use. In this presentation, I will discuss my experience with these freely available (but perhaps not truly open-source) computer codes. Although users are allowed to make modifications to the codes (on conditions that they provide a copy of the modified version) only a handful of users have tried to make any modification, and only rarely are modifications even reported, much less provided back to the developers.

Serial evaluation of the MODS, SOFA and LOD scores to predict ICU mortality in mixed critically ill patients.

PubMed

Khwannimit, Bodin

2008-09-01

To perform a serial assessment and compare ability in predicting the intensive care unit (ICU) mortality of the multiple organ dysfunction score (MODS), sequential organ failure assessment (SOFA) and logistic organ dysfunction (LOD) score. The data were collected prospectively on consecutive ICU admissions over a 24-month period at a tertiary referral university hospital. The MODS, SOFA, and LOD scores were calculated on initial and repeated every 24 hrs. Two thousand fifty four patients were enrolled in the present study. The maximum and delta-scores of all the organ dysfunction scores correlated with ICU mortality. The maximum score of all models had better ability for predicting ICU mortality than initial or delta score. The areas under the receiver operating characteristic curve (AUC) for maximum scores was 0.892 for the MODS, 0.907 for the SOFA, and 0.92for the LOD. No statistical difference existed between all maximum scores and Acute Physiology and Chronic Health Evaluation II (APACHE II) score. Serial assessment of organ dysfunction during the ICU stay is reliable with ICU mortality. The maximum scores is the best discrimination comparable with APACHE II score in predicting ICU mortality.

Aerobic Fitness Level Typical of Elite Athletes is not Associated With Even Faster VO2 Kinetics During Cycling Exercise

PubMed Central

Figueira, Tiago R.; Caputo, Fabrizio; Machado, Carlos E.P.; Denadai, Benedito S.

2008-01-01

The aim of this study was to address the question if the VO2 kinetics is further improved as the aerobic training status increases from trained to elite level athletes. Maximal oxygen uptake (VO2max), work-rate associated to VO2max (IVO2max) and VO2 kinetics of moderate (Mod) and maximal exercise (Max) were determined in fifty- five subjects. Then, they were assigned into three groups: low (LF), intermediate (IF) and high (HF) aerobic fitness level. In average, the VO2max of LF, IF and HF groups were, respectively, 36.0 ± 3.1, 51.1 ± 4.5 and 68.1 ± 3.9 ml·kg·min-1 (p ≤ 0.05 among each other). VO2 kinetics mean response time of both exercise intensities were significantly faster (p ≤ 0.05) in HF (Mod, 27.5 ± 5.5 s; Max, 32.6 ± 8.3 s) and IF (Mod, 25.0 ± 3.1 s; Max, 42.6 ± 10.4 s) when compared to LF (Mod, 35.7 ± 7.9 s; Max: 57.8 ± 17.8 s). We can conclude that VO2 kinetics is improved as the fitness level is increased from low to intermediate but not further improved as the aerobic fitness level increases from intermediate to high. Key points Currently, it is reasonable to believe that the rate-limiting step of VO2 kinetics depends on exercise intensity. The well known physiological adaptations induced by endurance training are likely the most extreme means to overcome rate-limiting steps determining VO2 kinetics across exercise intensities. However, exercise adaptation leading individuals to the high-end of aerobic fitness level range (VO2max > 65 ml.kg.min-1) is not able to further improve VO2 kinetics during both, moderate and maximal intensity exercise. PMID:24150145

Doubling diet fat on sugar ratio in children with mitochondrial OXPHOS disorders: Effects of a randomized trial on resting energy expenditure, diet induced thermogenesis and body composition.

PubMed

Béghin, Laurent; Coopman, Stéphanie; Schiff, Manuel; Vamecq, Joseph; Mention-Mulliez, Karine; Hankard, Régis; Cuisset, Jean-Marie; Ogier, Hélène; Gottrand, Frédéric; Dobbelaere, Dries

2016-12-01

Mitochondrial OXPHOS disorders (MODs) affect one or several complexes of respiratory chain oxidative phosphorylation. An increased fat/low-carbohydrate ratio of the diet was recommended for treating MODs without, however, evaluating its potential benefits through changes in the respective contributions of cell pathways (glycolysis, fatty acid oxidation) initiating energy production. Therefore, the objective of the present work was to compare Resting Energy Expenditure (REE) under basal diet (BD) and challenging diet (CD) in which fat on sugar content ratio was doubled. Diet-induced thermogenesis (DIT) and body compositions were also compared. Energetic vs regulatory aspects of increasing fat contribution to total nutritional energy input were essentially addressed through measures primarily aiming at modifying total fat amounts and not the types of fats in designed diets. In this randomized cross-over study, BD contained 10% proteins/30% lipids/60% carbohydrates (fat on sugar ratio = 0.5) and was the imposed diet at baseline. CD contained 10% proteins/45% lipids/45% carbohydrates (fat on sugar ratio = 1). Main and second evaluation criteria measured by indirect calorimetry (QUARK RMR ® , Cosmed, Pavona; Italy) were REE and DIT, respectively. Thirty four MOD patients were included; 22 (mean age 13.2 ± 4.7 years, 50% female; BMI 16.9 ± 4.2 kg/m 2 ) were evaluated for REE, and 12 (mean age 13.8 ± 4.8 years, 60% female; BMI 17.4 ± 4.6 kg/m 2 ) also for DIT. OXPHOS complex deficiency repartition in 22 analysed patients was 55% for complex I, 9% for complex III, 27% for complex IV and 9% for other proteins. Neither carry-over nor period effects were detected (p = 0.878; ANOVA for repeated measures). REE was similar between BD vs CD (1148.8 ± 301.7 vs 1156.1 ± 278.8 kcal/day; p = 0.942) as well as DIT (peak DIT 260 vs 265 kcal/day; p = 0.842) and body composition (21.9 ± 13.0 vs 21.6 ± 13.3% of fat mass; p = 0.810). Doubling diet fat on sugar ratio does not appear to improve, per se, energetic status and body composition of patients with MODs. Copyright © 2016 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Automotive Stirling Engine Mod 1 Design Review, Volume 1

NASA Technical Reports Server (NTRS)

1982-01-01

Risk assessment, safety analysis of the automotive stirling engine (ASE) mod I, design criteria and materials properties for the ASE mod I and reference engines, combustion are flower development, and the mod I engine starter motor are discussed. The stirling engine system, external heat system, hot engine system, cold engine system, and engine drive system are also discussed.

B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA)

DTIC Science & Technology

2015-12-01

Selected Acquisition Report ( SAR ) RCS: DD-A&T(Q&A)823-468 B61 Mod 12 Life Extension Program Tailkit Assembly (B61 Mod 12 LEP TKA) As of FY 2017... SAR March 23, 2016 10:38:20 UNCLASSIFIED 2 Table of Contents Common Acronyms and Abbreviations for MDAP Programs 3 Program Information...Unit Cost B61 Mod 12 LEP TKA December 2015 SAR March 23, 2016 10:38:20 UNCLASSIFIED 3 PB - President’s Budget PE - Program Element PEO - Program

Department of the Navy Justification of Estimates for Fiscal Year 1984 Submitted to Congress January 1983. Operation & Maintenance, Navy. Book 2. Budget Activity 7: Central Supply & Maintenance.

DTIC Science & Technology

1983-01-01

Sidewinder TD Mods 2/1,291 3/1,762 4/5,540 Cost $130 $252 $573 Snarrow TD Mods 5/2,045 2/186 6/564 Cost $556 $110 $419 Shrike TD Mods -/- 4/2,930 3/2,307 Cost...574 $713 Standard Arm TO/Mods 1/87 ?/351 ?/296 Cost $72 $180 $158 Phoenix TD /Mods 4/889 4/554 3/642 Cost $219 $120 $?67 7 29 Activity Group: Air...Launched Weapons Rework (cont’d) III. Performance Criteria and Evaluation FY 1982 FY 1983 FY 1984 (cont’d) Harpoon TD /Mods 6/396 16/2,512 14/1,195

Environmental Assessment Newport Research Facility Irish Hill

DTIC Science & Technology

2011-09-12

Classification Symbol Burdett silt loam, 3 to 8 percent BuB Not Hydric Prime Farmland if Drained slopes Honeoye and Lansing silt loams, Hre Not...Part USDA - llap unit symbol BuB ~ CsB HrE HsD HIB HtC LnC LnD McB MIS ~ MoB I MoD NaB NaC NaD I 1R0 •ShF llap unit Mille Rating

Higher exercise intensity delays postexercise recovery of impedance-derived cardiac sympathetic activity.

PubMed

Michael, Scott; Jay, Ollie; Graham, Kenneth S; Davis, Glen M

2017-08-01

Systolic time intervals (STIs) provide noninvasive insights into cardiac sympathetic neural activity (cSNA). As the effect of exercise intensity on postexercise STI recovery is unclear, this study investigated the STI recovery profile after different exercise intensities. Eleven healthy males cycled for 8 min at 3 separate intensities: LOW (40%-45%), MOD (75%-80%), and HIGH (90%-95%) of heart-rate (HR) reserve. Bio-impedance cardiography was used to assess STIs - primarily pre-ejection period (PEP; inversely correlated with cSNA), as well as left ventricular ejection time (LVET) and PEP:LVET - during 10 min seated recovery immediately postexercise. Heart-rate variability (HRV), i.e., natural-logarithm of root mean square of successive differences (Ln-RMSSD), was calculated as an index of cardiac parasympathetic neural activity (cPNA). Higher preceding exercise intensity elicited a slower recovery of HR and Ln-RMSSD (p < 0.001), and these measures did not return to baseline by 10 min following any intensity (p ≤ 0.009). Recovery of STIs was also slower following higher intensity exercise (p ≤ 0.002). By 30 s postexercise, higher preceding intensity resulted in a lower PEP (98 ± 14 ms, 75 ± 6 ms, 66 ± 5 ms for LOW, MOD, and HIGH, respectively, p < 0.001). PEP recovered to baseline (143 ± 11 ms) by 5 min following LOW (139 ± 13 ms, p = 0.590) and by 10 min following MOD (145 ± 17 ms, p = 0.602), but was still suppressed at 10 min following HIGH (123 ± 21 ms, p = 0.012). Higher preceding exercise intensity attenuated the recovery of indices for cSNA (from STIs) and cPNA (from HRV) in a graded dose-response fashion. While exercise intensity must be considered, acute recovery may be a valuable period during which to concurrently monitor these noninvasive indices, to identify potentially abnormal cardiac autonomic responses.

airGR: a suite of lumped hydrological models in an R-package

NASA Astrophysics Data System (ADS)

Coron, Laurent; Perrin, Charles; Delaigue, Olivier; Andréassian, Vazken; Thirel, Guillaume

2016-04-01

Lumped hydrological models are useful and convenient tools for research, engineering and educational purposes. They propose catchment-scale representations of the precipitation-discharge relationship. Thanks to their limited data requirements, they can be easily implemented and run. With such models, it is possible to simulate a number of hydrological key processes over the catchment with limited structural and parametric complexity, typically evapotranspiration, runoff, underground losses, etc. The Hydrology Group at Irstea (Antony) has been developing a suite of rainfall-runoff models over the past 30 years with the main objectives of designing models as efficient as possible in terms of streamflow simulation, applicable to a wide range of catchments and having low data requirements. This resulted in a suite of models running at different time steps (from hourly to annual) applicable for various issues including water balance estimation, forecasting, simulation of impacts and scenario testing. Recently, Irstea has developed an easy-to-use R-package (R Core Team, 2015), called airGR, to make these models widely available. It includes: - the water balance annual GR1A (Mouehli et al., 2006), - the monthly GR2M (Mouehli, 2003) models, - three versions of the daily model, namely GR4J (Perrin et al., 2003), GR5J (Le Moine, 2008) and GR6J (Pushpalatha et al., 2011), - the hourly GR4H model (Mathevet, 2005), - a degree-day snow module CemaNeige (Valéry et al., 2014). The airGR package has been designed to facilitate the use by non-expert users and allow the addition of evaluation criteria, models or calibration algorithms selected by the end-user. Each model core is coded in FORTRAN to ensure low computational time. The other package functions (i.e. mainly the calibration algorithm and the efficiency criteria) are coded in R. The package is already used for educational purposes. The presentation will detail the main functionalities of the package and present a case study application. References: - Le Moine, N. (2008), Le bassin versant de surface vu par le souterrain : une voie d'amélioration des performances et du réalisme des modèles pluie-débit ?, PhD thesis (in French), UPMC, Paris, France. - Mathevet, T. (2005), Quels modèles pluie-débit globaux pour le pas de temps horaire ? Développement empirique et comparaison de modèles sur un large échantillon de bassins versants, PhD thesis (in French), ENGREF - Cemagref (Antony), Paris, France. - Mouelhi S. (2003), Vers une chaîne cohérente de modèles pluie-débit conceptuels globaux aux pas de temps pluriannuel, annuel, mensuel et journalier, PhD thesis (in French), ENGREF - Cemagref Antony, Paris, France. - Mouelhi, S., C. Michel, C. Perrin and V. Andréassian (2006), Stepwise development of a two-parameter monthly water balance model, Journal of Hydrology, 318(1-4), 200-214, doi:10.1016/j.jhydrol.2005.06.014. - Perrin, C., C. Michel and V. Andréassian (2003), Improvement of a parsimonious model for streamflow simulation, Journal of Hydrology, 279(1-4), 275-289, doi:10.1016/S0022-1694(03)00225-7. - Pushpalatha, R., C. Perrin, N. Le Moine, T. Mathevet and V. Andréassian (2011), A downward structural sensitivity analysis of hydrological models to improve low-flow simulation, Journal of Hydrology, 411(1-2), 66-76, doi:10.1016/j.jhydrol.2011.09.034. - R Core Team (2015). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. URL https://www.R-project.org/ - Valéry, A., V. Andréassian and C. Perrin (2014), "As simple as possible but not simpler": What is useful in a temperature-based snow-accounting routine? Part 2 - Sensitivity analysis of the Cemaneige snow accounting routine on 380 catchments, Journal of Hydrology, doi:10.1016/j.jhydrol.2014.04.058.

Near Surface Thermal Stratification during Summer at Summit, Greenland, and its Impact on MODIS-derived Surface Temperatures

NASA Astrophysics Data System (ADS)

Adolph, A. C.; Albert, M. R.; Hall, D. K.

2017-12-01

As rapid warming of the Arctic occurs, it is imperative that we monitor climate parameters such as temperature over large areas to understand and predict the extent of climate changes. Temperatures are often tracked using in-situ 2 m air temperatures, but in remote locations such as on the Greenland Ice Sheet, temperature can be studied more comprehensively using remote sensing techniques. Because of the presence of surface-based temperature inversions in ice-covered areas, differences between 2 m air temperature and skin temperature can be significant and are particularly relevant when considering validation and application of remote sensing temperature data. We present results from a field campaign at Summit Station in Greenland to study surface temperature using the following measurements: skin temperature measured by IR sensors, thermochrons, and thermocouples; 2 m air temperature measured by a NOAA meteorological station; and two different MODerate-resolution Imaging Spectroradiometer (MODIS) surface temperature products. We confirm prior findings that in-situ 2 m air temperature is often significantly higher in the summer than in-situ skin temperature when incoming solar radiation and wind speed are low. This inversion may account for biases in previous MODIS surface temperature studies that used 2 m air temperature for validation. As compared to the in-situ IR skin temperature measurements, the MOD/MYD11 Collection 6 surface-temperature standard product has an RMSE of 1.0°C, and that the MOD29 Collection 6 product has an RMSE of 1.5°C, spanning a range of temperatures from -35°C to -5°C. For our study area and time series, MODIS surface temperature products agree with skin temperatures better than many previous studies have indicated, especially at temperatures below -20°C where other studies found a significant cold bias. Further investigation at temperatures below -35°C is warranted to determine if this bias does indeed exist.

Shutdown characteristics of the Mod-O wind turbine with aileron controls

NASA Technical Reports Server (NTRS)

Miller, D. R.; Corrigan, R. D.

1984-01-01

Horizontal-axis wind turbines utilize partial or full variable blade pitch to regulate rotor speed. The weight and costs of these systems indicated a need for alternate methods of rotor control. Aileron control is an alternative which has potential to meet this need. The NASA Lewis Research Center has been experimentally testing aileron control rotors on the Mod-U wind turbine to determine their power regulation and shutdown characteristics. Experimental and analytical shutdown test results are presented for a 38 percent chord aileron-control rotor. These results indicated that the 38 percent chord ailerons provided overspeed protection over the entire Mod-O operational windspeed range, and had a no-load equilibrium tip speed ratio of 1.9. Thus, the 38 percent chord ailerons had much improved aerodynamic braking capability when compared with the first aileron-control rotor having 20 percent chord ailerons.

Real-time Image Processing for Microscopy-based Label-free Imaging Flow Cytometry in a Microfluidic Chip.

PubMed

Heo, Young Jin; Lee, Donghyeon; Kang, Junsu; Lee, Keondo; Chung, Wan Kyun

2017-09-14

Imaging flow cytometry (IFC) is an emerging technology that acquires single-cell images at high-throughput for analysis of a cell population. Rich information that comes from high sensitivity and spatial resolution of a single-cell microscopic image is beneficial for single-cell analysis in various biological applications. In this paper, we present a fast image-processing pipeline (R-MOD: Real-time Moving Object Detector) based on deep learning for high-throughput microscopy-based label-free IFC in a microfluidic chip. The R-MOD pipeline acquires all single-cell images of cells in flow, and identifies the acquired images as a real-time process with minimum hardware that consists of a microscope and a high-speed camera. Experiments show that R-MOD has the fast and reliable accuracy (500 fps and 93.3% mAP), and is expected to be used as a powerful tool for biomedical and clinical applications.

Mod-0A Wind Turbine in Block Island, Rhode Island

NASA Image and Video Library

1979-06-21

A Mod-0A 200-kilowatt wind turbine designed by National Aeronautics and Space Administration (NASA) Lewis Research Center and constructed in Block Island, Rhode Island. The wind turbine program was a joint program between NASA and the Energy Research and Development Administration (ERDA) during the 1970s to develop less expensive forms of energy. NASA Lewis was assigned the responsibility of developing large horizontal-axis wind turbines. The program included a series of increasingly powerful wind turbines, designated: Mod-0A, Mod-1, WTS-4, and Mod-5. The program’s first device was a Mod-0 100-kilowatt wind turbine test bed at NASA’s Plum Brook Station. This Mod-0A 200-kilowatt turbine, completed in 1977, was the program’s second-generation device. It included a 125-foot diameter blade atop a 100-foot tall tower. This early wind turbine was designed determine its operating problems, integrate with the local utilities, and assess the attitude of the local community. There were additional Mod-0A turbines built in Culebra, Puerto Rico; Clayton, New Mexico; and Oahu, Hawaii. The Mod-0A turbines suffered durability issues with the rotor blade and initially appeared unreliable. NASA engineers addressed the problems, and the turbines proved to be reliable and efficient devices that operated for a number of years. The information gained from these early models was vital to the design and improvement of the later generations.

Enhanced Vascular Effects of Cyclic GMP in Septic Rat Aorta

DTIC Science & Technology

1988-01-01

enzyme in turn catalyzes Integrative Comp. Physiol. 23): R436-R442, 1988--The mod- the synthesis of 3’,5’-cyclic monophosp#* (cGMP), ulation of... synthesis of endogenous cGMP or after aug- significant disparity in cGMP content of tissue from mentation of intracellular cGMP concentration by treat...and a proposal. J. Vascular reactivity in endotoxin shock: effect of lidocaine or in- Surg. Res. 29: 189-201, 1980. UNCLASSIFIED SECURITY CLASSIFICATION

Method for evaluating wind turbine wake effects on wind farm performance

NASA Technical Reports Server (NTRS)

Neustadter, H. E.; Spera, D. A.

1985-01-01

A method of testing the performance of a cluster of wind turbine units an data analysis equations are presented which together form a simple and direct procedure for determining the reduction in energy output caused by the wake of an upwind turbine. This method appears to solve the problems presented by data scatter and wind variability. Test data from the three-unit Mod-2 wind turbine cluster at Goldendale, Washington, are analyzed to illustrate the application of the proposed method. In this sample case the reduction in energy was found to be about 10 percent when the Mod-2 units were separated a distance equal to seven diameters and winds were below rated.

Proof without Words: Squares Modulo 3

ERIC Educational Resources Information Center

Nelsen, Roger B.

2013-01-01

Using the fact that the sum of the first n odd numbers is n[superscript 2], we show visually that n[superscript 2] is the same as 0 (mod 3) when n is the same as 0 (mod 3), and n[superscript 2] is the same as 1 (mod 3) when n is the same as plus or minus 1 (mod 3).

Estimation of crop gross primary production (GPP): fAPAR_chl versus MOD15A2 FPAR

USDA-ARS?s Scientific Manuscript database

Within leaf chloroplasts chlorophylls absorb photosynthetically active radiation (PAR) for photosynthesis (PSN). The MOD15A2 FPAR (fraction of PAR absorbed by canopy, i.e., fAPARcanopy) product has been widely used to compute absorbed PAR for PSN (APARPSN). The MOD17A2 algorithm uses MOD15A2 FPAR i...

Plasma Irisin Modestly Increases during Moderate and High-Intensity Afternoon Exercise in Obese Females

PubMed Central

Winn, Nathan C.; Grunewald, Zachary I.; Liu, Ying; Heden, Timothy D.; Nyhoff, Lauren M.; Kanaley, Jill A.

2017-01-01

Background and Purpose Irisin is an exercise-responsive myokine that has been proposed to exert anti-obesity benefits; yet its response during exercise in obese women is not described. This study characterized plasma irisin levels during a single bout of afternoon isocaloric-exercise of different intensities (moderate- vs high-intensity) in obese females. Methods Eleven obese females participated in 3 randomized study days beginning at 1600h: 1) no exercise (NoEx), 2) moderate exercise (ModEx; 55%VO2max) and 3) high intensity interval exercise (IntEx; 4 min (80%VO2max)/3 min (50% VO2max). Frequent blood samples were analyzed for glucose and lactate (whole-blood), and insulin, c-peptide, glucagon, and irisin (plasma) throughout 190 min of testing. Results Plasma irisin increased above baseline during ModEx and IntEx (P<0.05), but not NoEx (P>0.05). Peak irisin levels during ModEx and IntEx exercise were 11.9± 3.4% and 12.3 ± 4.1% relative to baseline (P<0.05), respectively, with no differences between exercise intensities (P>0.05). Irisin levels remained elevated above resting for 125 minutes post-exercise during ModEx, whereas levels returned to baseline within 15 minutes post-exercise during IntEx. Similarly, no associations were found between plasma irisin levels and circulating lactate, glucose, insulin, c-peptide, or glucagon among study days (P>0.05). However, there was an inverse association between basal irisin and lean mass (r = -0.70, P = 0.01). Conclusion A single bout of moderate and high intensity afternoon exercise induces modest increases in circulating irisin concentrations during exercise; however the regulation post-exercise appears to be dimorphic between exercise intensity in obese females. Future studies are needed to compare morning and afternoon exercise on irisin secretion. PMID:28125733

Cement Thickness of Inlay Restorations Made of Lithium Disilicate, Polymer-Infiltrated Ceramic and Nano-Ceramic CAD/CAM Materials Evaluated Using 3D X-Ray Micro-Computed Tomography.

PubMed

Uzgur, Recep; Ercan, Ertuğrul; Uzgur, Zeynep; Çolak, Hakan; Yalçın, Muhammet; Özcan, Mutlu

2016-08-12

To evaluate the marginal and internal cement thicknesses of inlay restorations made of various CAD/CAM materials using 3D X-ray micro-computed tomography (micro-CT) technique. Caries-free extracted mandibular molars (N = 30) with similar size were randomly assigned to three groups (N = 10 per group). Mesio-occlusal-distal (MOD) cavities were prepared, and inlay restorations were obtained by milling out CAD/CAM materials namely, (a) IPS: monolithic lithium disilicate (control), (b) VE: polymer-infiltrated ceramic, and (c) CS: nano-ceramic using a CAM unit. Marginal and internal cement thicknesses were measured using 3D micro-CT. Data were analyzed using 1-way ANOVA and Tukey's tests (alpha = 0.05). The mean marginal and internal cement thickness were not significant in all inlay materials (p > 0.05). Mean marginal cement thickness (μm) was the lowest for the IPS group (67.54 ± 10.16) followed by VE (84.09 ± 3.94) and CS (95.18 ± 10.58) (p > 0.05). The internal cement thickness (μm) was the lowest in the CS group (54.85 ± 6.94) followed by IPS (60.58 ± 9.22) and VE (77.53 ± 12.13) (p > 0.05). Marginal and internal cement thicknesses of MOD inlays made of monolithic lithium disilicate, polymer-infiltrated ceramic, and nano-ceramic CAD/CAM materials were similar and all less than 100 μm, which could be considered clinically acceptable. MOD inlays made of different CAD/CAM materials presented similar cement thickness, less than 100 μm. © 2016 by the American College of Prosthodontists.

Transport performance of a HTS current lead prepared by the TFA-MOD processed YBCO tapes

NASA Astrophysics Data System (ADS)

Shiohara, K.; Sakai, S.; Ohki, S.; Yamada, Y.; Tachikawa, K.; Koizumi, T.; Aoki, Y.; Hikichi, Y.; Nishioka, J.; Hasegawa, T.

2009-10-01

A superconducting current lead has been prepared using 12 tapes of the trifluoroacetates - metal organic deposition (TFA-MOD) processed Y 1Ba 2Cu 3O 7-δ (YBCO) coated conductors with critical current ( I c) of about 100 A at 77 K in self-field. The tapes are 4.5 mm in width, 220 mm in length and about 120 μm in overall thickness. The 1 μm thick superconducting YBCO layer was formed through the TFA-MOD process on Hastelloy TM substrate tapes with two buffer oxide layers of Gd 2Zr 2O 7 (GZO) and CeO 2. The 12 YBCO tapes were arrayed on the both sides (six tapes on each side) of a stainless steel board with 3 mm in thickness for a board type shape. They were similarly soldered to copper caps at the both ends. The transport current of 1000 A was stably applied for 10 min in the liquid nitrogen temperature without any voltage generation in all tapes. Although some voltage in some YBCO tapes generated at the applied currents of about 1100 A, the transport current of 1200 A was successfully applied without quenching. The voltage between both copper caps linearly increased with increasing the transport current, and it was about 300 μV at an applied current of 1000 A. A low joint resistance between the YBCO tapes and the copper caps resulted in small amounts of the Joule heating at the joints when 1000 A was applied. The overall (effective) thermal conductivity of the current leads composed of YBCO tapes and the stainless steel board was much lower than that of Non-superconducting current leads. Therefore, the present current leads with small heat leakage seemed to be practically promising for superconducting magnets.

Kinetic studies of divertor heat fluxes in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Pankin, A. Y.; Bateman, G.; Kritz, A. H.; Rafiq, T.; Park, G. Y.; Chang, C. S.; Brunner, D.; Hughes, J. W.; Labombard, B.; Terry, J.

2010-11-01

The kinetic XGC0 code [C.S. Chang et al, Phys. Plasmas 11 (2004) 2649] is used to model the H- mode pedestal and SOL regions in Alcator C-Mod discharges. The self-consistent simulations in this study include kinetic neoclassical physics and anomalous transport models along with the ExB flow shear effects. The heat fluxes on the divertor plates are computed and the fluxes to the outer plate are compared with experimental observations. The dynamics of the radial electric field near the separatrix and in the SOL region are computed with the XGC0 code, and the effect of the anomalous transport on the heat fluxes in the SOL region is investigated. In particular, the particle and thermal diffusivities obtained in the analysis mode are compared with predictions from the theory-based anomalous transport models such as MMM95 [G. Bateman et al, Phys. Plasmas 5 (1998) 1793] and DRIBM [T. Rafiq et al, to appear in Phys. Plasmas (2010)]. It is found that there is a notable pinch effect in the inner separatrix region. Possible physical mechanisms for the particle and thermal pinches are discussed.

Measurements of the parallel wavenumber of lower hybrid waves in the scrape-off layer of a high-density tokamak

NASA Astrophysics Data System (ADS)

Baek, S. G.; Wallace, G. M.; Shinya, T.; Parker, R. R.; Shiraiwa, S.; Bonoli, P. T.; Brunner, D.; Faust, I.; LaBombard, B. L.; Takase, Y.; Wukitch, S.

2016-05-01

In lower hybrid current drive (LHCD) experiments on tokamaks, the parallel wavenumber of lower hybrid waves is an important physics parameter that governs the wave propagation and absorption physics. However, this parameter has not been experimentally well-characterized in the present-day high density tokamaks, despite the advances in the wave physics modeling. In this paper, we present the first measurement of the dominant parallel wavenumber of lower hybrid waves in the scrape-off layer (SOL) of the Alcator C-Mod tokamak with an array of magnetic loop probes. The electric field strength measured with the probe in typical C-Mod plasmas is about one-fifth of that of the electric field at the mouth of the grill antenna. The amplitude and phase responses of the measured signals on the applied power spectrum are consistent with the expected wave energy propagation. At higher density, the observed k|| increases for the fixed launched k||, and the wave amplitude decreases rapidly. This decrease is correlated with the loss of LHCD efficiency at high density, suggesting the presence of loss mechanisms. Evidence of the spectral broadening mechanisms is observed in the frequency spectra. However, no clear modifications in the dominant k|| are observed in the spectrally broadened wave components, as compared to the measured k|| at the applied frequency. It could be due to (1) the probe being in the SOL and (2) the limited k|| resolution of the diagnostic. Future experiments are planned to investigate the roles of the observed spectral broadening mechanisms on the LH density limit problem in the strong single pass damping regime.

Experimental Test of Nonlocal Realism Using a Fiber-Based Source of Polarization-Entangled Photon Paris

DTIC Science & Technology

2008-03-25

J. F. Clauser and M. A. Horne, Phys. Rev. D 10, 526 1974. 6 A. Zeilinger , Rev. Mod. Phys. 71, S288 1999; A. Aspect, Nature London 398, 189...Jennewein, M. Zukowski, M. Aspelmeyer, and A. Zeilinger , Phys. Rev. Lett. 99, 210406 2007; C. Branciard, A. Ling, N. Gisin, C. Kurt- siefer, A. Lamas

A Generalization of the Euler-Fermat Theorem

ERIC Educational Resources Information Center

Harger, Robert T.; Harvey, Melinda E.

2003-01-01

This note considers the problem of determining, for fixed k and m, all values of r, 0 [less than] r [less than] [empty set](m), such that k[superscript [empty set](m)+1] [equivalent to] k[superscript r](mod m). More generally, if k, m and c are given, necessary and sufficient conditions are given for k[superscript c] [equivalent to] k[superscript…

Hurricane IKE Recovery Efforts - MOD Volunteers

NASA Image and Video Library

2008-09-18

Hurricane IKE Recovery Efforts - MOD Volunteers Location: Clear LAke Area Subject: MOD Volunteers assist fellow employees at their homes during the recovery from hurricane IKE. Photographer: Tom Murray (USA Photographer)

Experience and Assessment of the DOE/NASA Mod-1 2000 Kw Wind Turbine Generator at Boone, North Carolina

NASA Technical Reports Server (NTRS)

Collins, J. L.; Shaltens, R. K.; Poor, R. H.; Barton, R. S.

1982-01-01

The Mod 1 program objectives are defined. The Mod 1 wind turbine is described. In addition to the steel blade operated on the wind turbine, a composite blade was designed and manufactured. During the early phase of the manufacturing cycle of Mod 1A configuration was designed that identified concepts such as partial span control, a soft tower, and upwind teetered rotors that were incorporated in second and third generation industry designs. The Mod 1 electrical system performed as designed, with voltage flicker characteristics within acceptable utility limits.

Construction bidding cost of KSC's space shuttle facilities

NASA Technical Reports Server (NTRS)

Brown, Joseph Andrew

1977-01-01

The bidding cost of the major Space Transportation System facilities constructed under the responsibility of the John F. Kennedy Space Center (KSC) is described and listed. These facilities and Ground Support Equipment (GSE) are necessary for the receiving, assembly, testing, and checkout of the Space Shuttle for launch and landing missions at KSC. The Shuttle launch configuration consists of the Orbiter, the External Tank, and the Solid Rocket Boosters (SRB). The reusable Orbiter and SRB's is the major factor in the program that will result in lowering space travel costs. The new facilities are the Landing Facility; Orbiter Processing Facility; Orbiter Approach and Landing Test Facility (Dryden Test Center, California); Orbiter Mating Devices; Sound Suppression Water System; and Emergency Power System for LC-39. Also, a major factor was to use as much Apollo facilities and hardware as possible to reduce the facilities cost. The alterations to existing Apollo facilities are the VAB modifications; Mobile Launcher Platforms; Launch Complex 39 Pads A and B (which includes a new concept - the Rotary Service Structure), which was featured in ENR, 3 Feb. 1977, 'Hinged Space Truss will Support Shuttle Cargo Room'; Launch Control Center mods; External Tank and SRB Processing and Storage; Fluid Test Complex mods; O&C Spacelab mods; Shuttle mods for Parachute Facility; SRB Recovery and Disassembly Facility at Hangar 'AF'; and an interesting GSE item - the SRB Dewatering Nozzle Plug Sets (Remote Controlled Submarine System) used to inspect and acquire for reuse of SRB's.

Mod-2 wind turbine system development. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1982-01-01

Progress in the design, fabrication, and testing of a wind turbine system is reported. The development of the MOD-2 wind turbine through acceptance testing and initial operational evaluation is documented. The MOD-2 project intends to develop early commercialization of wind energy. The first wind turbine farm (three MOD-2 units) are now being operated at the Bonneville Power Administration site near Goldendale, Washington.

Cost-effectiveness analysis of microscopic observation drug susceptibility test versus Xpert MTB/Rif test for diagnosis of pulmonary tuberculosis in HIV patients in Uganda.

PubMed

Walusimbi, Simon; Kwesiga, Brendan; Rodrigues, Rashmi; Haile, Melles; de Costa, Ayesha; Bogg, Lennart; Katamba, Achilles

2016-10-10

Microscopic Observation Drug Susceptibility (MODS) and Xpert MTB/Rif (Xpert) are highly sensitive tests for diagnosis of pulmonary tuberculosis (PTB). This study evaluated the cost effectiveness of utilizing MODS versus Xpert for diagnosis of active pulmonary TB in HIV infected patients in Uganda. A decision analysis model comparing MODS versus Xpert for TB diagnosis was used. Costs were estimated by measuring and valuing relevant resources required to perform the MODS and Xpert tests. Diagnostic accuracy data of the tests were obtained from systematic reviews involving HIV infected patients. We calculated base values for unit costs and varied several assumptions to obtain the range estimates. Cost effectiveness was expressed as costs per TB patient diagnosed for each of the two diagnostic strategies. Base case analysis was performed using the base estimates for unit cost and diagnostic accuracy of the tests. Sensitivity analysis was performed using a range of value estimates for resources, prevalence, number of tests and diagnostic accuracy. The unit cost of MODS was US$ 6.53 versus US$ 12.41 of Xpert. Consumables accounted for 59 % (US$ 3.84 of 6.53) of the unit cost for MODS and 84 % (US$10.37 of 12.41) of the unit cost for Xpert. The cost effectiveness ratio of the algorithm using MODS was US$ 34 per TB patient diagnosed compared to US$ 71 of the algorithm using Xpert. The algorithm using MODS was more cost-effective compared to the algorithm using Xpert for a wide range of different values of accuracy, cost and TB prevalence. The cost (threshold value), where the algorithm using Xpert was optimal over the algorithm using MODS was US$ 5.92. MODS versus Xpert was more cost-effective for the diagnosis of PTB among HIV patients in our setting. Efforts to scale-up MODS therefore need to be explored. However, since other non-economic factors may still favour the use of Xpert, the current cost of the Xpert cartridge still needs to be reduced further by more than half, in order to make it economically competitive with MODS.

Risk Factors for Multiple Organ Dysfunction Syndrome in Severe Stroke Patients

PubMed Central

Yang, Shuna; Li, Yue; Yuan, Junliang; Yang, Lei; Li, Shujuan; Hu, Wenli

2016-01-01

Background Severe stroke patients have poor clinical outcome which may be associated with development of multiple organ dysfunction syndrome (MODS). Therefore, the aim of our study was to investigate independent risk factors for development of MODS in severe stroke patients. Methods Ninety seven severe stroke patients were prospective recruited from Jan 2011 to Jun 2015. The development of MODS was identified by Sequential Organ Failure Assessment (SOFA) score (score ≥ 3, at least two organs), which was assessed on day 1, 4, 7, 10 and 14 after admission. Baseline characteristics, Acute Physiology and Chronic Health Evaluation (APACHE) II score, Glasgow coma score (GCS) and cerebral imaging parameters were collected at admission. Cox regression was performed to determine predictors for the development of MODS. Medical complications after admission and in-hospital mortality were also investigated. Results 33 (34%) patients were in MODS group and 64 (66%) were in non-MODS group within 14 days after admission. Patients in MODS group had more smoker (51.5% vs 28.1%, p = 0.023), higher NIHSS score (23.48 ± 6.12 vs 19.81 ± 4.83, p = 0.004), higher APACHE II score (18.70 ± 5.18 vs 15.64 ± 4.36, p = 0.003) and lower GCS score (6.33 ± 2.48 vs 8.14 ± 2.73, p = 0.002). They also had higher rate of infarction in multi vascular territories (36.4% vs 10.9%, p = 0.003). The most common complication in all patients was pulmonary infection, while complication scores were comparable between two groups. Patients with MODS had higher in-hospital mortality (69.7% vs 9.4%, p = 0.000). In Cox regression, NIHSS score (RR = 1.084, 95% CI 1.019–1.153) and infarction in multi vascular territories (RR = 2.345 95% CI 1.105–4.978) were independent risk factors for development of MODS. Conclusions In acute phase of stroke, NIHSS score and infarction in multi vascular territories predicted MODS in severe stroke patients. Moreover, patients with MODS had higher in-hospital mortality, suggesting that early identification of MODS is critical important. PMID:27893797

Evaluating the Auto-MODS Assay, a Novel Tool for Tuberculosis Diagnosis for Use in Resource-Limited Settings

PubMed Central

Wang, Linwei; Mohammad, Sohaib H.; Li, Qiaozhi; Rienthong, Somsak; Rienthong, Dhanida; Nedsuwan, Supalert; Mahasirimongkol, Surakameth; Yasui, Yutaka

2014-01-01

There is an urgent need for simple, rapid, and affordable diagnostic tests for tuberculosis (TB) to combat the great burden of the disease in developing countries. The microscopic observation drug susceptibility assay (MODS) is a promising tool to fill this need, but it is not widely used due to concerns regarding its biosafety and efficiency. This study evaluated the automated MODS (Auto-MODS), which operates on principles similar to those of MODS but with several key modifications, making it an appealing alternative to MODS in resource-limited settings. In the operational setting of Chiang Rai, Thailand, we compared the performance of Auto-MODS with the gold standard liquid culture method in Thailand, mycobacterial growth indicator tube (MGIT) 960 plus the SD Bioline TB Ag MPT64 test, in terms of accuracy and efficiency in differentiating TB and non-TB samples as well as distinguishing TB and multidrug-resistant (MDR) TB samples. Sputum samples from clinically diagnosed TB and non-TB subjects across 17 hospitals in Chiang Rai were consecutively collected from May 2011 to September 2012. A total of 360 samples were available for evaluation, of which 221 (61.4%) were positive and 139 (38.6%) were negative for mycobacterial cultures according to MGIT 960. Of the 221 true-positive samples, Auto-MODS identified 212 as positive and 9 as negative (sensitivity, 95.9%; 95% confidence interval [CI], 92.4% to 98.1%). Of the 139 true-negative samples, Auto-MODS identified 135 as negative and 4 as positive (specificity, 97.1%; 95% CI, 92.8% to 99.2%). The median time to culture positivity was 10 days, with an interquartile range of 8 to 13 days for Auto-MODS. Auto-MODS is an effective and cost-sensitive alternative diagnostic tool for TB diagnosis in resource-limited settings. PMID:25378569

Large-scale wind turbine structures

NASA Technical Reports Server (NTRS)

Spera, David A.

1988-01-01

The purpose of this presentation is to show how structural technology was applied in the design of modern wind turbines, which were recently brought to an advanced stage of development as sources of renewable power. Wind turbine structures present many difficult problems because they are relatively slender and flexible; subject to vibration and aeroelastic instabilities; acted upon by loads which are often nondeterministic; operated continuously with little maintenance in all weather; and dominated by life-cycle cost considerations. Progress in horizontal-axis wind turbines (HAWT) development was paced by progress in the understanding of structural loads, modeling of structural dynamic response, and designing of innovative structural response. During the past 15 years a series of large HAWTs was developed. This has culminated in the recent completion of the world's largest operating wind turbine, the 3.2 MW Mod-5B power plane installed on the island of Oahu, Hawaii. Some of the applications of structures technology to wind turbine will be illustrated by referring to the Mod-5B design. First, a video overview will be presented to provide familiarization with the Mod-5B project and the important components of the wind turbine system. Next, the structural requirements for large-scale wind turbines will be discussed, emphasizing the difficult fatigue-life requirements. Finally, the procedures used to design the structure will be presented, including the use of the fracture mechanics approach for determining allowable fatigue stresses.

Helium experiments on Alcator C-Mod in support of ITER early operations

NASA Astrophysics Data System (ADS)

Kessel, C. E.; Wolfe, S. M.; Reinke, M. L.; Hughes, J. W.; Lin, Y.; Wukitch, S. J.; Baek, S. G.; Bonoli, P. T.; Chilenski, M.; Diallo, A.; the Alcator C-Mod Team

2018-05-01

Helium majority experiments on Alcator C-Mod were performed to compare with deuterium discharges, and inform ITER early operations. ELMy H-modes were produced with a special plasma shape at B T  =  5.3 T, I P  =  0.9 MA, at q 95 ~ 3.8. The He fraction ranged over, n He,L/n L  =  0.2-0.4, with n D,L/n L  =  0.15-0.26, compared to D plasmas with n D,L/n L  =  0.85-0.97. The power to enter the H-mode in He was found to be greater than ~2 times that for D discharges, in the low density region  <1.4  ×  1020/m3. However, it appears to follow the D threshold for higher densities. The stored energies in the He discharges were about 80% of those in D, and about 40% higher net power was required to sustain them compared to D. Global particle confinement times for tungsten of τ W* /τ E ~ 4 were obtained with ELMy H-modes in He, however accumulation occurred when the ELMs were irregular and infrequent. The electron temperatures and densities in the pedestal were similar between D and He discharges, and the ΔT e/T e and Δn e/n e values were similar or larger in He than D. The higher net power required to access the H-mode, and sustain it in flattop, for He discharges in C-Mod, imply some limitations for He operation in ITER.

Glutamate Oxaloacetate Transaminase (Got) Genetics in the Mouse: Polymorphism of Got-1

PubMed Central

Chapman, Verne M.; Ruddle, Frank H.

1972-01-01

We have examined a polymorphism for the soluble glutamate oxaloacetate (GOT-1) isozyme system which was found in the Asian mouse Mus castaneus. Variants of GOT-1 segregate as though they are controlled by codominant alleles for a single autosomal locus which we have designated Got-1. No close linkage of genes for soluble and mitochondrial forms of the enzyme, GOT-1 and GOT-2 respectively, was observed. Furthermore, no close linkage of Got-1 and the loci c, Gpi-1, Mod-2, Mod-1, Ld-1, Gpd-1, Pgm-1 or Gpo-1 was observed. Our results demonstrate the utility of sampling Mus from diverse populations to extend the repertoire of polymorphic loci and the genetic linkage map. PMID:17248564

Analysis of the ductility dip cracking in the nickel-base alloy 617mod

NASA Astrophysics Data System (ADS)

Eilers, A.; Nellesen, J.; Zielke, R.; Tillmann, W.

2017-03-01

While testing steam leading power plant components made of the nickel-base alloy A617mod at elevated temperatures (700 °C), ductility dip cracking (DDC) was observed in welding seams and their surroundings. In order to clarify the mechanism of crack formation, investigations were carried out on welded specimens made of A617mod. Interrupted tensile tests were performed on tensile specimens taken from the area of the welding seam. To simulate the conditions, the tensile tests were conducted at a temperature of 700 °C and with a low strain rate. Local strain fields at grain boundaries and inside single grains were determined at different deformation states by means of two-dimensional digital image correlation (DIC). Besides the strain fields, local hardnesses (nanoindentation), energy dispersive X-Ray spectroscopy (EDX), and electron backscatter diffraction (EBSD) measurements were performed. Besides information concerning the grain orientation, the EBSD measurement provides information on the coincidence site lattice (CSL) at grain boundaries as well as the Schmid factor of single grains. All results of the analysis methods mentioned above were correlated and compared to each other and related to the crack formation. Among other things, correlations between strain fields and Schmid factors were determined. The investigations show that the following influences affect the crack formation: orientation of the grain boundaries to the direction of the loading, the orientation of the grains to each other (CSL), and grain boundary sliding.

Second-line drug susceptibility breakpoints for Mycobacterium tuberculosis using the MODS assay.

PubMed

Trollip, A P; Moore, D; Coronel, J; Caviedes, L; Klages, S; Victor, T; Romancenco, E; Crudu, V; Ajbani, K; Vineet, V P; Rodrigues, C; Jackson, R L; Eisenach, K; Garfein, R S; Rodwell, T C; Desmond, E; Groessl, E J; Ganiats, T G; Catanzaro, A

2014-02-01

To establish breakpoint concentrations for the fluoroquinolones (moxifloxacin [MFX] and ofloxacin [OFX]) and injectable second-line drugs (amikacin [AMK], kanamycin [KM] and capreomycin [CPM]) using the microscopic observation drug susceptibility (MODS) assay. A multinational study conducted between February 2011 and August 2012 in Peru, India, Moldova and South Africa. In the first phase, breakpoints for the fluoroquinolones and injectable second-line drugs (n = 58) were determined. In the second phase, MODS second-line drug susceptibility testing (DST) as an indirect test was compared to MGIT™ DST (n = 89). In the third (n = 30) and fourth (n = 156) phases, we determined the reproducibility and concordance of MODS second-line DST directly from sputum. Breakpoints for MFX (0.5 μg/ml), OFX (1 μg/ml), AMK (2 μg/ml), KM (5 μg/ml) and CPM (2.5 μg/ml) were determined. In all phases, MODS results were highly concordant with MGIT DST. The few discrepancies suggest that the MODS breakpoint concentrations for some drugs may be too low. MODS second-line DST yielded comparable results to MGIT second-line DST, and is thus a promising alternative. Further studies are needed to confirm the accuracy of the drug breakpoints and the reliability of MODS second-line DST as a direct test.

Serotonin and the neuropeptide PDF initiate and extend opposing behavioral states in C. elegans.

PubMed

Flavell, Steven W; Pokala, Navin; Macosko, Evan Z; Albrecht, Dirk R; Larsch, Johannes; Bargmann, Cornelia I

2013-08-29

Foraging animals have distinct exploration and exploitation behaviors that are organized into discrete behavioral states. Here, we characterize a neuromodulatory circuit that generates long-lasting roaming and dwelling states in Caenorhabditis elegans. We find that two opposing neuromodulators, serotonin and the neuropeptide pigment dispersing factor (PDF), each initiate and extend one behavioral state. Serotonin promotes dwelling states through the MOD-1 serotonin-gated chloride channel. The spontaneous activity of serotonergic neurons correlates with dwelling behavior, and optogenetic modulation of the critical MOD-1-expressing targets induces prolonged dwelling states. PDF promotes roaming states through a Gαs-coupled PDF receptor; optogenetic activation of cAMP production in PDF receptor-expressing cells induces prolonged roaming states. The neurons that produce and respond to each neuromodulator form a distributed circuit orthogonal to the classical wiring diagram, with several essential neurons that express each molecule. The slow temporal dynamics of this neuromodulatory circuit supplement fast motor circuits to organize long-lasting behavioral states. Copyright © 2013 Elsevier Inc. All rights reserved.

The multi-spectral line-polarization MSE system on Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mumgaard, R. T., E-mail: mumgaard@psfc.mit.edu; Khoury, M.; Scott, S. D.

A multi-spectral line-polarization motional Stark effect (MSE-MSLP) diagnostic has been developed for the Alcator C-Mod tokamak wherein the Stokes vector is measured in multiple wavelength bands simultaneously on the same sightline to enable better polarized background subtraction. A ten-sightline, four wavelength MSE-MSLP detector system was designed, constructed, and qualified. This system consists of a high-throughput polychromator for each sightline designed to provide large étendue and precise spectral filtering in a cost-effective manner. Each polychromator utilizes four narrow bandpass interference filters and four custom large diameter avalanche photodiode detectors. Two filters collect light to the red and blue of the MSEmore » emission spectrum while the remaining two filters collect the beam pi and sigma emission generated at the same viewing volume. The filter wavelengths are temperature tuned using custom ovens in an automated manner. All system functions are remote controllable and the system can be easily retrofitted to existing single-wavelength line-polarization MSE systems.« less

The multi-spectral line-polarization MSE system on Alcator C-Mod

DOE PAGES

Mumgaard, R. T.; Scott, S. D.; Khoury, M.

2016-08-17

A multi-spectral line-polarization motional Stark effect (MSE-MSLP) diagnostic has been developed for the Alcator C-Mod tokamak wherein the Stokes vector is measured in multiple wavelength bands simultaneously on the same sightline to enable better polarized background subtraction. A ten-sightline, four wavelength MSE-MSLP detector system was designed, constructed, and qualified. This system consists of a high-throughput polychromator for each sightline designed to provide large étendue and precise spectral filtering in a cost-effective manner. Each polychromator utilizes four narrow bandpass interference filters and four custom large diameter avalanche photodiode detectors. Two filters collect light to the red and blue of the MSEmore » emission spectrum while the remaining two filters collect the beam pi and sigma emission generated at the same viewing volume. The filter wavelengths are temperature tuned using custom ovens in an automated manner. Furthermore, all system functions are remote controllable and the system can be easily retrofitted to existing single-wavelength line-polarization MSE systems.« less

Serotonin and the Neuropeptide PDF Initiate and Extend Opposing Behavioral States in C. elegans

PubMed Central

Flavell, Steven W.; Pokala, Navin; Macosko, Evan Z.; Albrecht, Dirk R.; Larsch, Johannes; Bargmann, Cornelia I.

2013-01-01

SUMMARY Foraging animals have distinct exploration and exploitation behaviors that are organized into discrete behavioral states. Here we characterize a neuromodulatory circuit that generates long-lasting roaming and dwelling states in Caenorhabditis elegans. We find that two opposing neuromodulators, serotonin and the neuropeptide pigment dispersing factor (PDF), each initiate and extend one behavioral state. Serotonin promotes dwelling states through the MOD-1 serotonin-gated chloride channel. The spontaneous activity of serotonergic neurons correlates with dwelling behavior, and optogenetic modulation of the critical MOD-1-expressing targets induces prolonged dwelling states. PDF promotes roaming states through a Gαs-coupled PDF receptor; optogenetic activation of cAMP production in PDF receptor-expressing cells induces prolonged roaming states. The neurons that produce and respond to each neuromodulator form a distributed circuit orthogonal to the classical wiring diagram, with several essential neurons that express each molecule. The slow temporal dynamics of this neuromodulatory circuit supplement fast motor circuits to organize long-lasting behavioral states. PMID:23972393

Transport of light, trace impurities in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Rowan, W. L.; Bespamyatnov, I. O.; Liao, K. T.; Horton, W.; Fu, X. R.; Hughes, J. W.

2012-10-01

Light impurity profiles for boron were measured in ITB, H-mode, L-mode, and I-mode discharges in Alcator C-Mod. Within this wide range of modes, the profiles varied from peaked to hollow to flat. Specifically, hollow profiles are often observed in H-mode, while ITBs produce strong peaking, and L-mode produces moderate peaking. I-mode discharges are characterized by flat impurity profiles. For the study reported here, the profiles were measured with charge exchange recombination spectroscopy. The dependences of Rv/D were sought on dimensionless quantities including ion density scale length, effective charge, collisionality, and temperature scale length. We find that neoclassical transport consistently underestimates the measured transport. The excess measured transport is assumed to be turbulent. The strongest dependence of Rv/D is with temperature scale length. In addition, the measured transport was compared with the prediction of an analytical theory of drift wave turbulence that identifies transport implications for drift waves driven by ion and impurity density gradients.

EMC3-EIRENE modelling of toroidally-localized divertor gas injection experiments on Alcator C-Mod

DOE PAGES

Lore, Jeremy D.; Reinke, M. L.; LaBombard, Brian; ...

2014-09-30

Experiments on Alcator C-Mod with toroidally and poloidally localized divertor nitrogen injection have been modeled using the three-dimensional edge transport code EMC3-EIRENE to elucidate the mechanisms driving measured toroidal asymmetries. In these experiments five toroidally distributed gas injectors in the private flux region were sequentially activated in separate discharges resulting in clear evidence of toroidal asymmetries in radiated power and nitrogen line emission as well as a ~50% toroidal modulation in electron pressure at the divertor target. The pressure modulation is qualitatively reproduced by the modelling, with the simulation yielding a toroidal asymmetry in the heat flow to the outermore » strike point. Finally, toroidal variation in impurity line emission is qualitatively matched in the scrape-off layer above the strike point, however kinetic corrections and cross-field drifts are likely required to quantitatively reproduce impurity behavior in the private flux region and electron temperatures and densities directly in front of the target.« less

Comportement rhéologique des systèmes mixtes biopolymères / protéines

NASA Astrophysics Data System (ADS)

Rebiha, M.; Moulai-Mostefa, N.; Sadok, A. Hadj; Sabri, N.

2005-05-01

Dans ce travail, on s'est intéressé à l'étude des effets du caséinate de sodium et du xanthane sur les propriétés rhéologiques des solutions aqueuses, préparées suivant un plan d'expériences. Les caractéristiques mécaniques obtenues sont traduites par les coefficients du modèle rhéologique de Casson, en l'occurrence la contrainte seuil, τ 0, et la viscosité plastique, η _c. Ainsi, à l'issue de la modélisation en surface de réponses, il apparaît une interaction répulsive à l'échelle structurale entre le caséinate de sodium et le xanthane, traduite par un abaissement considérable de τ 0. Cet baissement de la rigidité peut conduire à une séparation de phases, phénomène conditionné par la viscosité limite de Casson,η _c.

Model-on-Demand Predictive Control for Nonlinear Hybrid Systems With Application to Adaptive Behavioral Interventions

PubMed Central

Nandola, Naresh N.; Rivera, Daniel E.

2011-01-01

This paper presents a data-centric modeling and predictive control approach for nonlinear hybrid systems. System identification of hybrid systems represents a challenging problem because model parameters depend on the mode or operating point of the system. The proposed algorithm applies Model-on-Demand (MoD) estimation to generate a local linear approximation of the nonlinear hybrid system at each time step, using a small subset of data selected by an adaptive bandwidth selector. The appeal of the MoD approach lies in the fact that model parameters are estimated based on a current operating point; hence estimation of locations or modes governed by autonomous discrete events is achieved automatically. The local MoD model is then converted into a mixed logical dynamical (MLD) system representation which can be used directly in a model predictive control (MPC) law for hybrid systems using multiple-degree-of-freedom tuning. The effectiveness of the proposed MoD predictive control algorithm for nonlinear hybrid systems is demonstrated on a hypothetical adaptive behavioral intervention problem inspired by Fast Track, a real-life preventive intervention for improving parental function and reducing conduct disorder in at-risk children. Simulation results demonstrate that the proposed algorithm can be useful for adaptive intervention problems exhibiting both nonlinear and hybrid character. PMID:21874087

Post-test analysis of PIPER-ONE PO-IC-2 experiment by RELAP5/MOD3 codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bovalini, R.; D`Auria, F.; Galassi, G.M.

1996-11-01

RELAP5/MOD3.1 was applied to the PO-IC-2 experiment performed in PIPER-ONE facility, which has been modified to reproduce typical isolation condenser thermal-hydraulic conditions. RELAP5 is a well known code widely used at the University of Pisa during the past seven years. RELAP5/MOD3.1 was the latest version of the code made available by the Idaho National Engineering Laboratory at the time of the reported study. PIPER-ONE is an experimental facility simulating a General Electric BWR-6 with volume and height scaling ratios of 1/2,200 and 1./1, respectively. In the frame of the present activity a once-through heat exchanger immersed in a pool ofmore » ambient temperature water, installed approximately 10 m above the core, was utilized to reproduce qualitatively the phenomenologies expected for the Isolation Condenser in the simplified BWR (SBWR). The PO-IC-2 experiment is the flood up of the PO-SD-8 and has been designed to solve some of the problems encountered in the analysis of the PO-SD-8 experiment. A very wide analysis is presented hereafter including the use of different code versions.« less

Mobility on Demand Operational Concept Report.

DOT National Transportation Integrated Search

2017-09-10

This operational concept report provides an overview of the Mobility on Demand (MOD) concept and its evolution, description of the MOD ecosystem in a supply and demand framework, and its stakeholders and enablers. Leveraging the MOD ecosystem framewo...

MOD-2 wind turbine system concept and preliminary design report. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1979-01-01

The configuration development of the MOD-2 wind turbine system (WTS) is documented. The MOD-2 WTS project is a continuation of DOE programs to develop and achieve early commercialization of wind energy. The MOD-2 is design optimized for commercial production rates which, in multiunit installations, will be integrated into a utility power grid and achieve a cost of electricity at less than four cents per kilowatt hour.

Development of a sharp interface model that simulates coastal aquifer flow with the coupled use of GIS

NASA Astrophysics Data System (ADS)

Gemitzi, Alexandra; Tolikas, Demetrios

A simulation program, which works seamlessly with GIS and simulates flows in coastal aquifers, is presented in the present paper. The model is based on the Galerkin finite element discretization scheme and it simulates both steady and transient freshwater and saltwater flow, assuming that the two fluids are separated by a sharp interface. The model has been verified in simple cases where analytical solutions exist. The simulation program works as a tool of the GIS program, which is the main database that stores and manages all the necessary data. The combined use of the simulation and the GIS program forms an integrated management tool offering a simpler way of simulating and studying saline intrusion in coastal aquifers. Application of the model to the Yermasogia aquifer illustrates the coupled use of modeling and GIS techniques for the examination of regional coastal aquifer systems. Pour étudier un système aquifère côtier, nous avons développé un modèle aux éléments finis en quasi 3-D qui simule les écoulements d'eau douce et d'eau salée en régime aussi bien permanent que transitoire. Les équations qui les régissent sont discrétisées par un schéma de discrétisation de Garlekin aux éléments finis. Le modèle a été vérifié dans des cas simples où il existe des solutions analytiques. Toutes les données nécessaires sont introduites et gérées grâce à un logiciel de gestion de SIG. Le programme de simulation est utilisé comme un outil du logiciel de SIG, constituant ainsi un outil de gestion intégrée dont le but est de simuler et d'étudier l'intrusion saline dans les aquifères côtiers. L'application du modèle à l'aquifère de Yermasogia illustre l'utilisation couplée de la modélisation et des techniques de SIG pour l'étude des systèmes aquifères côtiers régionaux. Se ha desarrollado un modelo casi tridimensional de elementos finitos para simular el flujo de agua dulce y salada, tanto en régimen estacionario como en transitorio, en sistemas acuíferos costeros, bajo la hipótesis de separación por medio de una interfaz abrupta. Las ecuaciones del modelo han sido discretizadas mediante un esquema de Galerkin de discretización en elementos finitos. El modelo ha sido verificado en casos sencillos para los que existe solución analítica. Todos los datos necesarios se introducen y gestionan con un Sistema de Información Geográfica [SIG] por ordenador. El programa de simulación forma parte del programa de SIG, constituyendo una herramienta integrada de gestión para estudiar la intrusión salina en acuíferos costeros. La aplicación del modelo al acuífero de Yermasogia ilustra el uso acoplado de las técnicas de modelación y de SIG con el fin de examinar sistemas acuíferos costeros a escala regional.

MOD: An In-Situ Organic Detector for the MSR 2003 Mission

NASA Technical Reports Server (NTRS)

Kminek, G.; Bada, J. L.; Botta, O.; Glavin, D. P.; Grunthaner, F. J.; LaBaw, C. C.; Serviss, O. E.

2000-01-01

Looking for organic compounds that are essential for biochemistry or indicative of extraterrestrial organic influx is the primary goal of MOD (Mars Organic Detector). MOD can also quantify adsorbed and chemisorbed water and evolved carbon dioxide.

Characterization of completely k-magic regular graphs

NASA Astrophysics Data System (ADS)

Eniego, A. A.; Garces, I. J. L.

2017-10-01

Let k ∈ ℕ and c ∈ ℤ k . A graph G is said to be c-sum k-magic if there is a labeling ℓ : E(G) → ℤ k {0} such that Σ u∈N(v) ℓ(uv) ≡ c (mod k) for every vertex v of G, where N(v) is the neighborhood of v in G. We say that G is completely k-magic whenever it is c-sum k-magic for every c ∈ ℤ k . In this paper, we characterize all completely k-magic regular graphs.

Water use efficiency of net primary production in global terrestrial ecosystems

NASA Astrophysics Data System (ADS)

Xia, Lei; Wang, Fei; Mu, Xingmin; Jin, Kai; Sun, Wenyi; Gao, Peng; Zhao, Guangju

2015-07-01

The carbon and water cycles of terrestrial ecosystems, which are strongly coupled via water use efficiency (WUE), are influenced by global climate change. To explore the relationship between the carbon and water cycles and predict the effect of climate change on terrestrial ecosystems, it is necessary to study the WUE in global terrestrial ecosystems. In this study, the 13-year WUE (i.e., net primary production (NPP)/evapotranspiration (ET)) of global terrestrial ecosystems was calculated based on the Moderate Resolution Imaging Spectro-radiometer (MODIS) NPP (MOD17A3) and ET (MOD16A3) products from 2000 to 2012. The results indicate that the annual average WUE decreased but not significantly, and the 13-year mean value was 868.88 mg C m -2 mm -1. The variation trend of WUE value for each pixel differed greatly across the terrestrial ecosystems. A significant variation ( P<0.05) occurred in about 18.50% of the land surface. WUE was spatially distributed from 0 to 2541 mg C m -2 mm -1, and 58.78% of the WUE values were concentrated in the interval of 600-1200 mg C m -2 mm -1. The WUE increased from north to south in Africa and Oceania and from east to west in Europe and South America. Both latitudinal and longitudinal gradients existed in Asia and North America. The following trends in the WUE of different continents and Köppen-Geiger climates were observed: Europe (1129.71 mg C m -2 mm -1)> Oceania (1084.46 mg C m -2 mm -1)> Africa (893.51 mg C m -2 mm -1)> South America (893.07 mg C m -2 mm -1)> North America (870.79 mg C m -2 mm -1)> Asia (738.98 mg C m -2 mm -1) and warm temperate climates (1094 mg C m -2 mm -1)> snowy climates (862 mg C m -2 mm -1)> arid climates (785 mg C m -2 mm -1)> equatorial climates (732 mg C m -2 mm -1)> polar climates (435 mg C m -2 mm -1). Based on the WUE value and the present or future rainfall, the maximum carbon that fixed in one region may be theoretically calculated. Also, under the background of global climatic change, WUE may be regarded as an important reference for allotting CO 2 emissions offsets and carbon transactions.

Targeting Extracellular Histones with Novel RNA Bio drugs for the Treatment of Acute Lung Injury

DTIC Science & Technology

2017-10-01

organ involved in MODS is the lung (referred to as acute respiratory distress syndrome or ARDS). Trauma, smoke inhalation, burns, radiation , severe...and mortality associated with multiple organ dysfunction/ acute respiratory distress syndrome (MODS/ARDS) and ALI that can be easily delivered in combat...MODS, the risk of death is 40%. The most common organ involved in MODS is the lungs (referred to as acute respiratory distress syndrome or ARDS

Feasibility of using auto Mod-MPI system, a novel technique for automated measurement of fetal modified myocardial performance index.

PubMed

Lee, M-Y; Won, H-S; Jeon, E-J; Yoon, H C; Choi, J Y; Hong, S J; Kim, M-J

2014-06-01

To evaluate the reproducibility of measurement of the fetal left modified myocardial performance index (Mod-MPI) determined using a novel automated system. This was a prospective study of 116 ultrasound examinations from 110 normal singleton pregnancies at 12 + 1 to 37 + 1 weeks' gestation. Two experienced operators each measured the left Mod-MPI twice manually and twice automatically using the Auto Mod-MPI system. Intra- and interoperator reproducibility were assessed using intraclass correlation coefficients (ICCs) and the manual and automated measurements obtained by the more experienced operator were compared using Bland-Altman plots and ICCs. Both operators successfully measured the left Mod-MPI in all cases using the Auto Mod-MPI system. For both operators, intraoperator reproducibility was higher when performing automated measurements (ICC = 0.967 and 0.962 for Operators 1 and 2, respectively) than when performing manual measurements (ICC = 0.857 and 0.856 for Operators 1 and 2, respectively). Interoperator agreement was also better for automated than for manual measurements (ICC = 0.930 vs 0.723, respectively). There was good agreement between the automated and manual values measured by the more experienced operator. The Auto Mod-MPI system is a reliable technique for measuring fetal left Mod-MPI and demonstrates excellent reproducibility. Copyright © 2013 ISUOG. Published by John Wiley & Sons Ltd.

COMPARISON OF DIFFERENT TRUNK ENDURANCE TESTING METHODS IN COLLEGE‐AGED INDIVIDUALS

PubMed Central

Krier, Amber D.; Nelson, Julie A.; Rogers, Michael A.; Stuke, Zachariah O.; Smith, Barbara S.

2012-01-01

Objective: Determine the reliability of two different modified (MOD1 and MOD2) testing methods compared to a standard method (ST) for testing trunk flexion and extension endurance. Participants: Twenty‐eight healthy individuals (age 26.4 ± 3.2 years, height 1.75 ± m, weight 71.8 ± 10.3 kg, body mass index 23.6 ± 3.4 m/kg2). Method: Trunk endurance time was measured in seconds for flexion and extension under the three different stabilization conditions. The MOD1 testing procedure utilized a female clinician (70.3 kg) and MOD2 utilized a male clinician (90.7 kg) to provide stabilization as opposed to the ST method of belt stabilization. Results: No significant differences occurred between flexion and extension times. Intraclass correlations (ICCs3,1) for the different testing conditions ranged from .79 to .95 (p <.000) and are found in Table 3. Concurrent validity using the ST flexion times as the gold standard coefficients were .95 for MOD1 and .90 for MOD2. For ST extension, coefficients were .91 and .80, for MOD1 and MOD2 respectively (p <.01). Conclusions: These methods proved to be a reliable substitute for previously accepted ST testing methods in normal college‐aged individuals. These modified testing procedures can be implemented in athletic training rooms and weight rooms lacking appropriate tables for the ST testing. Level of Evidence: 3 PMID:23091786

The conceptualization model problem—surprise

NASA Astrophysics Data System (ADS)

Bredehoeft, John

2005-03-01

The foundation of model analysis is the conceptual model. Surprise is defined as new data that renders the prevailing conceptual model invalid; as defined here it represents a paradigm shift. Limited empirical data indicate that surprises occur in 20-30% of model analyses. These data suggest that groundwater analysts have difficulty selecting the appropriate conceptual model. There is no ready remedy to the conceptual model problem other than (1) to collect as much data as is feasible, using all applicable methods—a complementary data collection methodology can lead to new information that changes the prevailing conceptual model, and (2) for the analyst to remain open to the fact that the conceptual model can change dramatically as more information is collected. In the final analysis, the hydrogeologist makes a subjective decision on the appropriate conceptual model. The conceptualization problem does not render models unusable. The problem introduces an uncertainty that often is not widely recognized. Conceptual model uncertainty is exacerbated in making long-term predictions of system performance. C'est le modèle conceptuel qui se trouve à base d'une analyse sur un modèle. On considère comme une surprise lorsque le modèle est invalidé par des données nouvelles; dans les termes définis ici la surprise est équivalente à un change de paradigme. Des données empiriques limitées indiquent que les surprises apparaissent dans 20 à 30% des analyses effectuées sur les modèles. Ces données suggèrent que l'analyse des eaux souterraines présente des difficultés lorsqu'il s'agit de choisir le modèle conceptuel approprié. Il n'existe pas un autre remède au problème du modèle conceptuel que: (1) rassembler autant des données que possible en utilisant toutes les méthodes applicables—la méthode des données complémentaires peut conduire aux nouvelles informations qui vont changer le modèle conceptuel, et (2) l'analyste doit rester ouvert au fait que le modèle conceptuel peut bien changer lorsque des nouvelles informations apparaissent. Dans l'analyse finale le hydrogéologue prend une décision subjective sur le modèle conceptuel approprié. Le problème du le modèle conceptuel ne doit pas rendre le modèle inutilisable. Ce problème introduit une incertitude qui n'est pas toujours reconnue. Les incertitudes du modèle conceptuel deviennent plus importantes dans les cases de prévisions à long terme dans l'analyse de performance. La base para hacer un análisis de un modelo es el modelo conceptual. Se define aquí la sorpresa como los datos nuevos que convierten en incoherente al modelo conceptual previamente aceptado; tal como se define aquí esto representa un cambio de paradigma. Los datos empíricos limitados indican que estas sorpresas suceden entre un 20 a un 30% de los análisis de modelos. Esto sugiere que los analistas de modelos de agua subterránea tienen dificultades al seleccionar el modelo conceptual apropiado. No hayotra solución disponible a este problema del modelo conceptual diferente de: (1) Recolectar tanta información como sea posible, mediante la utilización de todos los métodos aplicables, lo cual puede resultar en que esta nueva información ayude a cambiar el modelo conceptual vigente, y (2) Que el analista de modelos se mantenga siempre abierto al hecho de que un modelo conceptual puede cambiar de manera total, en la medida en que se colecte mas información. En el análisis final el hidrogeólogo toma una decisión subjetiva en cuanto al modelo conceptual apropiado. El problema de la conceptualización no produce modelos inútiles. El problema presenta una incertidumbre, la cual a menudo no es tenida en cuentade manera adecuada. Esta incertidumbre en los modelos conceptuales se aumenta, cuando se hacen predicciones a largo plazo del comportamiento de un sistema dado.

Fatigue impact on Mod-1 wind turbine design

NASA Technical Reports Server (NTRS)

Stahle, C. V., Jr.

1978-01-01

Fatigue is a key consideration in the design of a long-life Wind Turbine Generator (WTG) system. This paper discusses the fatigue aspects of the large Mod-1 horizontal-axis WTG design starting with the characterization of the environment and proceeding through the design. Major sources of fatigue loading are discussed and methods of limiting fatigue loading are described. NASTRAN finite element models are used to determine dynamic loading and internal cyclic stresses. Recent developments in determining the allowable fatigue stress consistent with present construction codes are discussed relative to their application to WTG structural design.

Comparative performance tests on the Mod-2, 2.5-mW wind turbine with and without vortex generators

NASA Technical Reports Server (NTRS)

Miller, G. E.

1995-01-01

A test program was conducted on the third Mod-2 unit at Goldendale, Washington, to systematically study the effect of vortex generators (VG's) on power performance. The subject unit was first tested without VG's to obtain baseline data. Vortex generators were then installed on the mid-blade assemblies, and the resulting 70% VG configuration was tested. Finally, vortex generators were mounted on the tip assemblies, and data was recorded for the 100% VG configuration. This test program and its results are discussed in this paper. The development of vortex generators is also presented.

Risk stratification and prognostic performance of the predisposition, infection, response, and organ dysfunction (PIRO) scoring system in septic patients in the emergency department: a cohort study.

PubMed

Chen, Yun-Xia; Li, Chun-Sheng

2014-04-16

The predisposition, infection, response and organ dysfunction (PIRO) staging system was designed as a stratification tool to deal with the inherent heterogeneity of septic patients. The present study was conducted to assess the performance of PIRO in predicting multiple organ dysfunction (MOD), intensive care unit (ICU) admission, and 28-day mortality in septic patients in the emergency department (ED), and to compare this scoring system with the Mortality in Emergency Department Sepsis (MEDS) and Acute Physiology and Chronic Health Evaluation (APACHE II) scores. Consecutive septic patients (n = 680) admitted to the ED of Beijing Chao-Yang Hospital were enrolled. PIRO, MEDS, and APACHE II scores were calculated for each patient on ED arrival. Organ function was reassessed within 3 days of enrollment. All patients were followed up for 28 days. Outcome criteria were the development of MOD within 3 days, ICU admission or death within 28 days after enrollment. The predictive ability of the four components of PIRO was analyzed separately. Receiver operating characteristic (ROC) curve and logistic regression analysis were used to assess the prognostic and risk stratification value of the scoring systems. Organ dysfunction independently predicted ICU admission, MOD, and 28-day mortality, with areas under the ROC curve (AUC) of 0.888, 0.851, and 0.816, respectively. The predictive value of predisposition, infection, and response was weaker than that of organ dysfunction. A negative correlation was found between the response component and MOD, as well as mortality. PIRO, MEDS, and APACHE II scores significantly differed between patients who did and did not meet the outcome criteria (P < 0.001). PIRO and APACHE II independently predicted ICU admission and MOD, but MEDS did not. All three systems were independent predictors of 28-day mortality with similar AUC values. The AUC of PIRO was 0.889 for ICU admission, 0.817 for MOD, and 0.744 for 28-day mortality. The AUCs of PIRO were significantly greater than those of APACHE II and MEDS (P < 0.05) in predicting ICU admission and MOD. The study indicates that PIRO is helpful for risk stratification and prognostic determinations in septic patients in the ED.

Validation of microscopic observation drug susceptibility testing for rapid, direct rifampicin and isoniazid drug susceptibility testing in patients receiving tuberculosis treatment

PubMed Central

Coronel, J; Roper, M H; Herrera, C; Bonilla, C; Jave, O; Gianella, C; Sabogal, I; Huancaré, V; Leo, E; Tyas, A; Mendoza-Ticona, A; Caviedes, L; Moore, D A J; Drancourt, M

2014-01-01

Drug susceptibility testing (DST) is often needed in patients clinically failing tuberculosis (TB) therapy. Most studies of phenotypic direct drug susceptibility tests, such as microscopic observation drug susceptibility (MODS) tests, have been performed in patients not receiving TB treatment. The effect of ongoing TB treatment on the performance of MODS direct DST has not been previously explored, but patients failing such therapy constitute an important target group. The aim of this study was to determine the performance of MODS direct rifampicin and isoniazid DST in patients clinically failing first-line TB treatment, and to compare MODS direct DST with indirect proportion method DST. Sputa from 264 TB patients were cultured in parallel in Lowenstein–Jensen (LJ) and MODS assays; strains were tested for rifampicin and isoniazid susceptibility by the proportion method at the national reference laboratory. Ninety-three samples were culture-positive by LJ and MODS (concordance of 96%; kappa 0.92). With conventional MODS plate DST reading (performed on the same day as the sample is classified as culture-positive), the isoniazid DST concordance was 96.8% (kappa 0.89), and the concordance for rifampicin susceptibility testing was 92.6% (kappa 0.80). Reading of MODS DST plates 1 week after cultures had been determined to be culture-positive improved overall performance marginally—the isoniazid DST concordance was 95.7% (kappa 0.85); and the rifampicin DST concordance was 96.8% (kappa 0.91). Sensitivity for detection of multidrug-resistant TB was 95.8%. MODS testing provided reliable rifampicin and isoniazid DST results for samples obtained from patients receiving TB therapy. A modified DST reading schedule for such samples, with a final reading 1 week after a MODS culture turns positive, marginally improves the concordance with reference DST. PMID:24107197

Automotive Stirling Engine Development Project

NASA Technical Reports Server (NTRS)

Ernst, William D.; Shaltens, Richard K.

1997-01-01

The development and verification of automotive Stirling engine (ASE) component and system technology is described as it evolved through two experimental engine designs: the Mod 1 and the Mod 2. Engine operation and performance and endurance test results for the Mod 1 are summarized. Mod 2 engine and component development progress is traced from the original design through hardware development, laboratory test, and vehicle installation. More than 21,000 hr of testing were accomplished, including 4800 hr with vehicles that were driven more dm 59,000 miles. Mod 2 engine dynamometer tests demonstrated that the engine system configuration had accomplished its performance goals for power (60 kW) and efficiency (38.5%) to within a few percent. Tests with the Mod 2 engine installed in a delivery van demonstrated combined metro-highway fuel economy improvements consistent with engine performance goals and the potential for low emission levels. A modified version of the Mod 2 has been identified as a manufacturable design for an ASE. As part of the ASE project, the Industry Test and Evaluation Program (ITEP), NASA Technology Utilization (TU) project, and the industry-funded Stirling Natural Gas Engine program were undertaken to transfer ASE technology to end users. The results of these technology transfer efforts are also summarized.

NetMOD version 1.0 user's manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion John

2014-01-01

NetMOD (Network Monitoring for Optimal Detection) is a Java-based software package for conducting simulation of seismic networks. Specifically, NetMOD simulates the detection capabilities of seismic monitoring networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes of signal and noise that are observed atmore » each of the stations. From these signal-to-noise ratios (SNR), the probability of detection can be computed given a detection threshold. This manual describes how to configure and operate NetMOD to perform seismic detection simulations. In addition, NetMOD is distributed with a simulation dataset for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) International Monitoring System (IMS) seismic network for the purpose of demonstrating NetMOD's capabilities and providing user training. The tutorial sections of this manual use this dataset when describing how to perform the steps involved when running a simulation.« less

Methodology, status, and plans for development and assessment of the RELAP5 code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, G.W.; Riemke, R.A.

1997-07-01

RELAP/MOD3 is a computer code used for the simulation of transients and accidents in light-water nuclear power plants. The objective of the program to develop and maintain RELAP5 was and is to provide the U.S. Nuclear Regulatory Commission with an independent tool for assessing reactor safety. This paper describes code requirements, models, solution scheme, language and structure, user interface validation, and documentation. The paper also describes the current and near term development program and provides an assessment of the code`s strengths and limitations.

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Pt. 86, App. V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Pt. 86, App. V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

40 CFR Appendix V to Part 86 - The Standard Road Cycle (SRC)

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Pt. 86, App. V Appendix V... engine) Idle 10 sec 0 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to 20 MPH −5 1 Mod accel to 30 MPH 4 1 Cruise at 30 MPH for 1/4 lap 0 1 Mod. decel to stop −5 1 Idle 5 sec 0 1...

Impurity transport in enhanced confinement regimes in RFX-mod Reversed Field Pinch

NASA Astrophysics Data System (ADS)

Carraro, Lorella; Menmuir, Sheena; Fassina, Alessandro

2010-11-01

The results of impurity transport studies in RFX-mod enhanced confinement quasi-single helicity (QSH) and single helical axis (SHAx) regimes are presented and discussed. The impurity diffusion coefficient and pinch velocity are obtained through comparing experimental emission pattern (line emission and SXR time evolutions, SXR profiles) with the results of a 1-D impurity transport code. Previous analysis [S. Menmuir et al. to be published in Plasma Phys. Contr. Fus.] of impurity transport in RFX-mod standard discharges showed that the impurity pinch velocity, always directed outwards, features a barrier with high values around r/a = 0.8, where the diffusion coefficient decreases by one order of magnitude. In the QSH regime, the transition region in D and v is more internal and the barrier in velocity is wider and stronger. New results have been obtained in experiments with Ni laser blow-off (LBO) injection in high current discharges (Ip>1.5 MA) with long lasting QSH, to better characterize the Ni behavior inside the helical magnetic topology.

Mission Operations Directorate - Success Legacy of the Space Shuttle Program (Overview of the Evolution and Success Stories from MOD During the Space Shuttle program)

NASA Technical Reports Server (NTRS)

Azbell, Jim A.

2011-01-01

In support of the Space Shuttle Program, as well as NASA's other human space flight programs, the Mission Operations Directorate (MOD) at the Johnson Space Center has become the world leader in human spaceflight operations. From the earliest programs - Mercury, Gemini, Apollo - through Skylab, Shuttle, ISS, and our Exploration initiatives, MOD and its predecessors have pioneered ops concepts and emphasized a history of mission leadership which has added value, maximized mission success, and built on continual improvement of the capabilities to become more efficient and effective. This paper provides specific examples that illustrate how MOD's focus on building and contributing value with diverse teams has been key to their successes both with the US space industry and the broader international community. This paper will discuss specific examples for the Plan, Train, Fly, and Facilities aspects within MOD. This paper also provides a discussion of the joint civil servant/contractor environment and the relative badge-less society within MOD. Several Shuttle mission related examples have also been included that encompass all of the aforementioned MOD elements and attributes, and are used to show significant MOD successes within the Shuttle Program. These examples include the STS-49 Intelsat recovery and repair, the (post-Columbia accident) TPS inspection process and the associated R-Bar Pitch Maneuver for ISS missions, and the STS-400 rescue mission preparation efforts for the Hubble Space Telescope repair mission. Since their beginning, MOD has consistently demonstrated their ability to evolve and respond to an ever changing environment, effectively prepare for the expected and successfully respond to the unexpected, and develop leaders, expertise, and a culture that has led to mission and Program success.

Microcolony culture techniques for tuberculosis diagnosis: a systematic review.

PubMed

Leung, E; Minion, J; Benedetti, A; Pai, M; Menzies, D

2012-01-01

There is considerable demand for quicker and more affordable yet accurate diagnostic tools for tuberculosis (TB). The microscopic observation drug susceptibility (MODS) assay and the thin-layer agar (TLA) assay are inexpensive, rapid microcolony-based culture methods. A systematic review and meta-analysis was performed to assess the accuracy and other test characteristics of MODS and TLA compared to a reference standard of traditional solid or liquid culture. Pooled estimates of sensitivity and specificity and their 95% confidence intervals were estimated with an exact binomial likelihood random effects meta-analysis. A total of 21 eligible studies were identified, 12 that evaluated MODS, seven that evaluated TLA and two that evaluated both. The overall pooled sensitivity and specificity of MODS were respectively 92% (95%CI 87-97) and 96% (90-100), and for TLA they were respectively 87% (95%CI 79-94) and 98% (95%CI 94-100), although there was considerable heterogeneity of results. When the studies were restricted to those assessing accuracy of MODS in sputum samples only, the sensitivity was 96% (95%CI 94-98) and the specificity 96% (95%CI 89-100). The mean intervals from reception of specimens to results were 9.2 days with MODS and 11.5 days with TLA; contamination rates averaged 6.6% with MODS and 12.3% with TLA; materials and supplies costs averaged US$1.48 for MODS and US$2.42 for TLA. MODS and TLA appear to be accurate and rapid yet inexpensive diagnostic tools for active TB. However, this review did not find sufficient evidence on the feasibility and costs of implementation of these tests, nor on the impact of these tests on patient outcomes.

An ultra-low background PMT for liquid xenon detectors

DOE PAGES

Akerib, D. S.; Bai, X.; Bernard, E.; ...

2012-11-15

Results are presented from radioactivity screening of two models of photomultiplier tubes designed for use in current and future liquid xenon experiments. The Hamamatsu 5.6 cm diameter R8778 PMT, used in the LUX dark matter experiment, has yielded a positive detection of four common radioactive isotopes: 238U, 232Th, 40K, and 60Co. Screening of LUX materials has rendered backgrounds from other detector materials subdominant to the R8778 contribution. A prototype Hamamatsu 7.6 cm diameter R11410 MOD PMT has also been screened, with benchmark isotope counts measured at <0.4 238U / <0.3 232Th / < 8.3 40K / 2.0+-0.2 60Co mBq/PMT. This represents a large reduction, equal to a change of xmore » $$\\frac{1}{24}$$ 238U / x $$\\frac{1}{9}$$ 232Th / x $$\\frac{1}{8}$$ 40K per PMT, between R8778 and R11410 MOD, concurrent with a doubling of the photocathode surface area (4.5 cm to 6.4 cm diameter). 60Co measurements are comparable between the PMTs, but can be significantly reduced in future R11410 MOD units through further material selection. Assuming PMT activity equal to the measured 90% upper limits, Monte Carlo estimates indicate that replacement of R8778 PMTs with R11410 MOD PMTs will change LUX PMT electron recoil background contributions by a factor of x $$\\frac{1}{25}$$ after further material selection for 60Co reduction, and nuclear recoil backgrounds by a factor of \\times $$\\frac{1}{36}$$. The strong reduction in backgrounds below the measured R8778 levels makes the R11410 MOD a very competitive technology for use in large-scale liquid xenon detectors.« less

Modèle tridimensionnel pour coupler les équations magnétiques et électriques dans le cas de la magnétostatique

NASA Astrophysics Data System (ADS)

Piriou, F.; Razek, A.

1991-03-01

In this paper a 3D model for coupling of magnetic and electric equations is presented. The magnetic equations are solved with the help of finite element method using the magnetic vector potential formulation. To take into account the effects of magnetic saturation we use the Newton-Raphson algorithm. We develop the analysis permitting the coupling of magnetic and electric equations to obtain a difrerential system equations which can be solved with numerical integration. As example we model an iron core coil and the validity of our model is verified by a comparison of the obtained results with an analytical solution and a 2D code calculation. Dans cet article est présenté un modèle 3D qui permet de coupler les équations magnétiques et électriques. Les équations magnétiques sont résolues à l'aide de la méthode des éléments finis en utilisant une formulation en potentiel vecteur magnétique. Dans le modèle proposé les effets de la saturation du circuit magnétique sont pris en compte en utilisant l'algorithme de Newton-Raphson. On montre comment relier les équations magnétiques avec celles du circuit électrique pour aboutir à un système d'équations différentielles que l'on résout avec une intégration numérique. A titre d'exemple on modélise une bobine à noyau ferromagnétique et pour montrer la validité du modèle on compare les résultats obtenus avec une solution analytique et un code de calcul 2D.

High-Fidelity Simulations of Electromagnetic Propagation and RF Communication Systems

DTIC Science & Technology

2017-05-01

addition to high -fidelity RF propagation modeling, lower-fidelity mod- els, which are less computationally burdensome, are available via a C++ API...expensive to perform, requiring roughly one hour of computer time with 36 available cores and ray tracing per- formed by a single high -end GPU...ER D C TR -1 7- 2 Military Engineering Applied Research High -Fidelity Simulations of Electromagnetic Propagation and RF Communication

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Astrophysics Data System (ADS)

Shaltens, R. K.; Birchenough, A. G.

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Technical Reports Server (NTRS)

Shaltens, R. K.; Birchenough, A. G.

1983-01-01

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Intestinal crosstalk – a new paradigm for understanding the gut as the “motor” of critical illness

PubMed Central

Clark, Jessica A; Coopersmith, Craig M

2007-01-01

For more than 20 years, the gut has been hypothesized to be the “motor” of multiple organ dysfunction syndrome (MODS). As critical care research has evolved, there have been multiple mechanisms by which the gastrointestinal tract has been proposed to drive systemic inflammation. Many of these disparate mechanisms have proved to be important in the origin and propagation of critical illness. However, this has led to an unusual situation where investigators describing the gut as a “motor” revving the systemic inflammatory response syndrome (SIRS) are frequently describing wholly different processes to support their claim (i.e. increased apoptosis, altered tight junctions, translocation, cytokine production, crosstalk with commensal bacteria, etc). The purpose of this review is to present a unifying theory as to how the gut drives critical illness. Although the gastrointestinal tract is frequently described simply as “the gut,” it is actually made up of a) an epithelium, b) a diverse and robust immune arm, which contains the majority of immune cells in the body, and c) the commensal bacteria, which contain more cells than are present in the entire host organism. We propose that the intestinal epithelium, the intestinal immune system and the intestine’s endogenous bacteria all play vital roles driving MODS, and the complex crosstalk between these three interrelated portions of the gastrointestinal tract are cumulatively what makes the gut a “motor” of critical illness. PMID:17577136

Corrosion Behavior of Candidate Materials Used for Urea Hydrolysis Equipment in Coal-Fired Selective Catalytic Reduction Units

NASA Astrophysics Data System (ADS)

Lu, Jintao; Yang, Zhen; Zhang, Bo; Huang, Jinyang; Xu, Hongjie

2018-05-01

Corrosion tests were performed in the laboratory in order to assess the corrosion resistance of candidate materials used in urea hydrolysis equipment. The materials to be evaluated were exposed at 145 °C for 1000 h. Alloys 316L, 316L Mod., HR3C, Inconel 718, and TC4 were evaluated. Additionally, aluminide and chromate coatings applied to a 316L substrate were examined. After exposure, the mass changes in the test samples were measured by a discontinuous weighing method, and the morphologies, compositions, and phases of the corrosion products were analyzed using scanning electron microscopy, energy-dispersive spectroscopy, and x-ray diffraction. Results indicated that continuous pitting and dissolution corrosion were the main failure modes for 316L stainless steel. 316L Mod. and HR3C alloy showed better corrosion resistance than 316L due to their relatively high Cr contents, but HR3C exhibited a strong tendency toward intergranular corrosion. Inconel 718, TC4, and aluminide and chromate coating samples showed similar corrosion processes: only depositions formed by hydrothermal reactions were observed. Based on these results, a possible corrosion process in the urea hydrolysis environment was discussed for these candidate materials and questions to be clarified were proposed.

Development of an Operational Land Water Mask for MODIS Collection 6, and Influence on Downstream Data Products

NASA Technical Reports Server (NTRS)

Carroll, M. L.; DiMiceli, C. M.; Townshend, J. R. G.; Sohlberg, R. A.; Elders, A. I.; Devadiga, S.; Sayer, A. M.; Levy, R. C.

2016-01-01

Data from the Moderate Resolution Imaging Spectro-radiometer (MODIS)on-board the Earth Observing System Terra and Aqua satellites are processed using a land water mask to determine when an algorithm no longer needs to be run or when an algorithm needs to follow a different pathway. Entering the fourth reprocessing (Collection 6 (C6)) the MODIS team replaced the 1 km water mask with a 500 m water mask for improved representation of the continental surfaces. The new water mask represents more small water bodies for an overall increase in water surface from 1 to 2 of the continental surface. While this is still a small fraction of the overall global surface area the increase is more dramatic in certain areas such as the Arctic and Boreal regions where there are dramatic increases in water surface area in the new mask. MODIS products generated by the on-going C6 reprocessing using the new land water mask show significant impact in areas with high concentrations of change in the land water mask. Here differences between the Collection 5 (C5) and C6 water masks and the impact of these differences on the MOD04 aerosol product and the MOD11 land surface temperature product are shown.

ITER L-Mode Confinement Database

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.M. Kaye and the ITER Confinement Database Working Group

This paper describes the content of an L-mode database that has been compiled with data from Alcator C-Mod, ASDEX, DIII, DIII-D, FTU, JET, JFT-2M, JT-60, PBX-M, PDX, T-10, TEXTOR, TFTR, and Tore-Supra. The database consists of a total of 2938 entries, 1881 of which are in the L-phase while 922 are ohmically heated (OH) only. Each entry contains up to 95 descriptive parameters, including global and kinetic information, machine conditioning, and configuration. The paper presents a description of the database and the variables contained therein, and it also presents global and thermal scalings along with predictions for ITER. The L-modemore » thermal confinement time scaling was determined from a subset of 1312 entries for which the thermal confinement time scaling was provided.« less

Minimal Niven Numbers

DTIC Science & Technology

2007-12-26

distribution in residue classes of integers with a fixed digit sum’, The Ramanujan J. 9 (2005), 45–62. [12] C . Mauduit and A. Sárközy, ‘On the arithmetic...28 19a. NAME OF RESPONSIBLE PERSON a. REPORT unclassified b. ABSTRACT unclassified c . THIS PAGE unclassified Standard Form 298 (Rev. 8-98...density zero. For the purpose of this section only, we omit the index and simply write C = {1 ≤ n : 2n+1 − 1 ≡ 2j (mod n) for some j = 1, 2

The neurobiology of modafinil as an enhancer of cognitive performance and a potential treatment for substance use disorders

PubMed Central

Mereu, Maddalena; Bonci, Antonello; Newman, Amy Hauck; Tanda, Gianluigi

2013-01-01

Rationale and Objectives Modafinil (MOD) and its R-enantiomer (R-MOD) are approved medications for narcolepsy and other sleep disorders. They have also been used, off label, as cognitive enhancers in populations of patients with mental disorders, including substance abusers that demonstrate impaired cognitive function. A debated non-medical use of MOD in healthy individuals to improve intellectual performance is raising questions about its potential abuse liability in this population. Results and Conclusions MOD has low micromolar affinity for the dopamine transporter (DAT). Inhibition of dopamine (DA) reuptake via the DAT explains the enhancement of DA levels in several brain areas, an effect shared with psychostimulants like cocaine, methylphenidate and the amphetamines. However, its neurochemical effects and anatomical pattern of brain area activation differ from typical psychostimulants and are consistent with its beneficial effects on cognitive performance processes such as attention, learning, and memory. At variance with typical psychostimulants, MOD shows very low, if any, abuse liability, in spite of its use as a cognitive enhancer by otherwise healthy individuals. Finally, recent clinical studies have focused on the potential use of MOD as a medication for treatment of drug abuse, but have not shown consistent outcomes. However, positive trends in several result measures suggest that medications that improve cognitive function, like MOD or R-MOD, may be beneficial for treatment of substance use disorders in certain patient populations. PMID:23934211

MBL-2 polymorphisms (codon 54 and Y-221X) and low MBL levels are associated with susceptibility to multi organ dysfunction in P. falciparum malaria in Odisha, India.

PubMed

Das, Bidyut K; Panda, Aditya K

2015-01-01

Mannose binding lectin, a plasma protein protects host from virus, bacteria, and parasites. Deficiency in MBL levels has been associated with susceptibility to various infectious diseases including P. falciparum malaria. Common MBL polymorphisms in promoter and coding regions are associated with decrease in plasma MBL levels or production of deformed MBL, respectively. In the present study, we hypothesized that MBL2 variants and plasma MBL levels could be associated with different clinical phenotypes of severe P. falciparum malaria. A hospital based study was conducted in eastern Odisha, India which is endemic to P. falciparum malaria. Common MBL-2 polymorphisms (codon 54, H-550L, and Y-221X) were typed in 336 cases of severe malaria (SM) [94 cerebral malaria (CM), 120 multi-organ dysfunction (MOD), 122 non-cerebral severe malaria (NCSM)] and 131 un-complicated malaria patients (UM). Plasma MBL levels were quantified by ELISA. Severe malaria patients displayed lower plasma levels of MBL compared to uncomplicated falciparum malaria. Furthermore, on categorization of severe malaria patients into various subtypes, plasma MBL levels were very low in MOD patients compared to other categories. Higher frequency of AB genotype and allele B was observed in MOD compared to UM (AB genotype: P = 0.006; B allele: P = 0.008). In addition, prevalence of YX genotype of MBL Y-221X polymorphism was also statistically more frequent in MOD case than UM (P = 0.009). The observations of the present study reveal that MBL-2 polymorphisms (codon 54 and Y-221X) and lower plasma MBL levels are associated with increased susceptibility to multi organ dysfunctions in P. falciparum malaria.

Economics of wind energy for utilities

NASA Technical Reports Server (NTRS)

Mccabe, T. F.; Goldenblatt, M. K.

1982-01-01

Utility acceptance of this technology will be contingent upon the establishment of both its technical and economic feasibility. This paper presents preliminary results from a study currently underway to establish the economic value of central station wind energy to certain utility systems. The results for the various utilities are compared specifically in terms of three parameters which have a major influence on the economic value: (1) wind resource, (2) mix of conventional generation sources, and (3) specific utility financial parameters including projected fuel costs. The wind energy is derived from modeling either MOD-2 or MOD-0A wind turbines in wind resources determined by a year of data obtained from the DOE supported meteorological towers with a two-minute sampling frequency. In this paper, preliminary results for six of the utilities studied are presented and compared.

Characterization of nanosized TiO2 synthesized inside a porous glass ceramic monolith by metallo-organic decomposition process

NASA Astrophysics Data System (ADS)

Mazali, Italo Odone; Alves, Oswaldo Luiz

2005-01-01

This work reports the preparation of TiO2 by decomposition of a metallo-organic precursor (MOD process) in the pores of an α-NbPO5 glass-ceramic monolith (PGC-NbP) and the study of the TiO2 anatase-rutile transition phase. The impregnation of titanium di-(propoxy)-di-(2-ethylhexanoate) in the PGC-NbP was confirmed by diffuse reflectance infrared spectroscopy. In the restrictive porous environment the decomposition of the metallo-organic compound exhibits a lower initial decomposition temperature but a higher final decomposition temperature, in comparison to the free precursor. The pure TiO2 rutile phase is formed only above 700 °C when the titanium precursor is decomposed outside the pores. The TiO2 anatase obtained inside the PGC-NbP was stabilized up to 750 °C and exhibits a smaller average crystallite size in comparison with the MOD process performed without PGC-NbP. Furthemore, the temperature of the TiO2 anatase-rutile transformation depends on crystallite size, which was provided by XRD and Raman spectroscopy. The precursor impregnation-decomposition cycle revealed a linear mass increment inside PGC-NbP. Micro-Raman spectroscopy shows the presence of a gradient concentration of the TiO2 inside the PGC-NbP. The use of the MOD process in the PGC-NbP pores has several advantages: control of the amount and the nature of the phase formed and preservation of the pore structure of PGC-NbP for subsequent treatments and reactions.

RAAS polymorphisms alter the acute blood pressure response to aerobic exercise among men with hypertension.

PubMed

Blanchard, Bruce E; Tsongalis, Gregory J; Guidry, Margaux A; LaBelle, Lisa A; Poulin, Michelle; Taylor, Amy L; Maresh, Carl M; Devaney, Joseph; Thompson, Paul D; Pescatello, Linda S

2006-05-01

Limited evidence suggests renin-angiotensin-aldosterone system (RAAS) polymorphisms alter the blood pressure (BP) response to aerobic exercise training. We examined if RAAS polymorphisms influenced postexercise hypotension in men with high normal to Stage 1 hypertension. Forty-seven men (44.2+/-1.4 years, 145.1+/-1.6/85.5+/-1.1 mmHg) randomly completed three experiments: seated rest (control) and two cycle exercise bouts at 40% (LITE) and 60% (MOD) of maximal oxygen consumption. Ambulating BP was measured for 14 h after each experiment. RAAS polymorphisms associated with hypertension (i.e. angiotensin converting I enzyme, ACE I/D; angiotensin II type 1 receptor, AT1R A/C; and intron 2 of aldosterone synthase, Int2 W/C) were analyzed using polymerase chain reaction and restriction enzyme digestion. Repeated measure ANOVA tested if BP differed between experimental conditions by RAAS genotypes. Compared to men with 0-2 variant alleles, men with > or =3 combined RAAS variant alleles had lower average systolic BP (SBP) (P=0.030) and lower average diastolic BP (DBP) (P=0.009) for 14 h only after LITE. In contrast, average BP was not different for MOD and control between RAAS variant allele groups over this time period (P> or =0.05). LITE reduced BP in men with > or =3 variant RAAS alleles for 14 h, whereas MOD had no influence on BP in these men. In order to optimally prescribe exercise for its BP lowering benefits in those with hypertension, additional knowledge of how genetic variation affects the BP response to exercise is needed.

Multi-scale gyrokinetic simulations of an Alcator C-Mod, ELM-y H-mode plasma

NASA Astrophysics Data System (ADS)

Howard, N. T.; Holland, C.; White, A. E.; Greenwald, M.; Rodriguez-Fernandez, P.; Candy, J.; Creely, A. J.

2018-01-01

High fidelity, multi-scale gyrokinetic simulations capable of capturing both ion ({k}θ {ρ }s∼ { O }(1.0)) and electron-scale ({k}θ {ρ }e∼ { O }(1.0)) turbulence were performed in the core of an Alcator C-Mod ELM-y H-mode discharge which exhibits reactor-relevant characteristics. These simulations, performed with all experimental inputs and realistic ion to electron mass ratio ({({m}i/{m}e)}1/2=60.0) provide insight into the physics fidelity that may be needed for accurate simulation of the core of fusion reactor discharges. Three multi-scale simulations and series of separate ion and electron-scale simulations performed using the GYRO code (Candy and Waltz 2003 J. Comput. Phys. 186 545) are presented. As with earlier multi-scale results in L-mode conditions (Howard et al 2016 Nucl. Fusion 56 014004), both ion and multi-scale simulations results are compared with experimentally inferred ion and electron heat fluxes, as well as the measured values of electron incremental thermal diffusivities—indicative of the experimental electron temperature profile stiffness. Consistent with the L-mode results, cross-scale coupling is found to play an important role in the simulation of these H-mode conditions. Extremely stiff ion-scale transport is observed in these high-performance conditions which is shown to likely play and important role in the reproduction of measurements of perturbative transport. These results provide important insight into the role of multi-scale plasma turbulence in the core of reactor-relevant plasmas and establish important constraints on the the fidelity of models needed for predictive simulations.

78 FR 69805 - Periodic Reporting (Proposals Six Through Nine)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-21

... MODS Operation Groups for Productivity Calculations The Postal Service states that Proposal Eight would... MODS productivity data (TPF or TPH per workhour) for a variety of operation groups related to letter, flat, parcel, and bundle sorting. The MODS productivity data are used to parameterize a number of cost...

Moving Past "Hello World": Learning to Mod in an Online Affinity Space

ERIC Educational Resources Information Center

Subramanian, Shree Durga

2012-01-01

Game modding has increasingly become a mainstream and "cutting edge" medium to foster a broad range of critical software design and programming practices to learners coming from wide-ranging educational and professional backgrounds. Participatory practices, like game modding, are highly interest-driven and entail intense engagement with…

A Literature Survey of Reverberation Modeling: With Emphasis on Bellhop Compatibility for Operational Applications

DTIC Science & Technology

2010-09-01

modèles à orientation opérationnelle ( comparativement à ceux orientés vers la recherche) qui pourraient être compatibles avec le modèle de propagation...concentre sur les modèles à orientation opérationnelle (en sacrifiant un certain degré d’exactitude pour accroître la réactivité, comparativement aux modèles...these modeling efforts are not applicable to Bellhop because they are designed specifically to take advantage of the normal mode decomposition

Lods, wrods, and mods: the interpretation of lod scores calculated under different models.

PubMed

Hodge, S E; Elston, R C

1994-01-01

In this paper we examine the relationships among classical lod scores, "wrod" scores (lod scores calculated under the wrong genetic model), and "mod" scores (lod scores maximized over genetic model parameters). We compare the behavior of these scores when the state of nature is linkage to their behavior when the state of nature is no linkage. We describe sufficient conditions for mod scores to be valid and discuss their use to determine the correct genetic model. We show that lod scores represent a likelihood-ratio test for independence. We explain the "ascertainment-assumption-free" aspect of using mod scores to determine mode of inheritance and we set this aspect into a well-established statistical framework. Finally, we summarize practical guidelines for the use of mod scores.

Note des Éditeurs scientifiques

NASA Astrophysics Data System (ADS)

Averbuch, P.

Cette série d'articles est une revue de résultats expérimentaux sur différents "fluides" moléculaires, dans lesquels la cohésion est due à des forces de Van der Waals et à des liaisons hydrogène, l'eau étant un de ces fluides. Ces résultats sont présentés de façon à justifier expérimentalement un modèle original, non extensif, des propriétés de ces fluides, et l'ensemble se présente sous la forme de trois articles décrivant le modèle, suivis chacun par un article le comparant aux résultats expérimentaux publiés par de nombreux auteurs. Le caractère non extensif des propriétés physiques des fluides est choquant, contraire à beaucoup d'idées établies, il semble n'avoir en sa faveur qu'un argument, la comparaison avec un nombre de résultats expérimentaux assez grand pour que l'effet du hasard soit difficilement soupçonnable. En particulier, les écarts entre des résultats de mesures faits par des auteurs différents dans des conditions différentes sont expliqués, le sérieux et la compétence des différents expérimentateurs ne sont plus mis en doute : mais l'interprétation de ces résultats avec un modèle extensif non adapté est seule mise en cause. Les modèles extensifs étant utilisés systématiquement, au delà des expériences de physiciens, dans les calculs d'ingénieurs, et dans la modélisation d'appareils qui fonctionnent et de phénomènes naturels observés par tout le monde, il fallait expliquer pourquoi on pouvait renoncer à l'extensivité. Les raisons du succès pratique des modèles extensifs sont données, d'abord dans le cas des nématiques, puis dans celui des liquides ordinaires, et c'est ce qui rend l'ensemble cohérent, tant avec les mesures physiques fines qu'avec les observations quotidiennes. Il n'en reste pas moins que si l'interprétation donnée dans cette série d'articles est généralisable, une justification théorique du modèle utilisé devient nécessaire. Pour ce qui est des propriétés d'équilibre, une séparation de l'énergie libre en énergie libre de volume et en énergie libre de surface devrait donner les mêmes résultats ; par contre les choses deviennent troublantes dès que l'on passe aux coefficients de transport, c'est-à-dire à l'aspect macroscopique de la dynamique moléculaire. Il y a là un écart notable avec les conceptions courantes, ce qui rend très surprenante la lecture de ces articles. On peut mentionner la liste des problèmes théoriques posés par la description phénoménologique qui est celle de cette série d'articles : la généralisation de lois d'échelle en dehors de zones critiques n'est pas absolument nouvelle, par contre la simplicité des lois reliant l'exposant v à la température pose problème ; le sens des temps de relaxation utilisés est sans doute également à préciser. Enfin les modes considérés semblent n'intervenir dans les propriétés thermodynamiques que par un facteur par mode, comme si seulement l'énergie potentielle devait intervenir, les termes cinétiques ne participant pas vraiment aux transitions de phase. Tout cela pose donc problème, et l'on peut se demander si un pareil modèle peut être compatible avec tout ce qui est connu par ailleurs en physique statistique. Mais s'il rend bien compte de beaucoup de résultats expérimentaux, ce sont ces derniers qui seraient en difficulté avec la mécanique statistique. Il a donc semblé préférable de publier le modèle, sa justification expérimentale et de poser quelques problèmes, tant aux théoriciens, qui pourraient expliquer pourquoi un tel modèle rend compte de résultats observés, qu'aux expérimentateurs, qui pourraient reprendre certaines mesures, et délimiter le caractère plus ou moins général du modèle.

Calibrated Hydrothermal Parameters, Barrow, Alaska, 2013

DOE Data Explorer

Atchley, Adam; Painter, Scott; Harp, Dylan; Coon, Ethan; Wilson, Cathy; Liljedahl, Anna; Romanovsky, Vladimir

2015-01-29

A model-observation-experiment process (ModEx) is used to generate three 1D models of characteristic micro-topographical land-formations, which are capable of simulating present active thaw layer (ALT) from current climate conditions. Each column was used in a coupled calibration to identify moss, peat and mineral soil hydrothermal properties to be used in up-scaled simulations. Observational soil temperature data from a tundra site located near Barrow, AK (Area C) is used to calibrate thermal properties of moss, peat, and sandy loam soil to be used in the multiphysics Advanced Terrestrial Simulator (ATS) models. Simulation results are a list of calibrated hydrothermal parameters for moss, peat, and mineral soil hydrothermal parameters.

Modélisation et simulation numérique du changement de phase liquide vapeur en cavité

NASA Astrophysics Data System (ADS)

Daru, Virginie; Duluc, Marie-Christine; Le Maître, Olivier; Juric, Damir; Le Quéré, Patrick

2006-01-01

A model for the simulation of boiling flow with phase change in a closed cavity is presented. A front-tracking method is used to deal with the liquid-vapor interface. The liquid phase is incompressible while the vapor phase is weakly compressible and obeys to the perfect gas law. This model can deal with large density ratio ( ρ/ρ≃1000) flows while accounting for the saturation curve. Computations are performed on a 1D validation case, idealizing a pressure cooker. Results are compared with a low Mach number approximation. To cite this article: V. Daru et al., C. R. Mecanique 334 (2006).

Performance of Linear and Nonlinear Two-Leaf Light Use Efficiency Models at Different Temporal Scales

DOE PAGES

Wu, Xiaocui; Ju, Weimin; Zhou, Yanlian; ...

2015-02-25

The reliable simulation of gross primary productivity (GPP) at various spatial and temporal scales is of significance to quantifying the net exchange of carbon between terrestrial ecosystems and the atmosphere. This study aimed to verify the ability of a nonlinear two-leaf model (TL-LUEn), a linear two-leaf model (TL-LUE), and a big-leaf light use efficiency model (MOD17) to simulate GPP at half-hourly, daily and 8-day scales using GPP derived from 58 eddy-covariance flux sites in Asia, Europe and North America as benchmarks. Model evaluation showed that the overall performance of TL-LUEn was slightly but not significantly better than TL-LUE at half-hourlymore » and daily scale, while the overall performance of both TL-LUEn and TL-LUE were significantly better (p < 0.0001) than MOD17 at the two temporal scales. The improvement of TL-LUEn over TL-LUE was relatively small in comparison with the improvement of TL-LUE over MOD17. However, the differences between TL-LUEn and MOD17, and TL-LUE and MOD17 became less distinct at the 8-day scale. As for different vegetation types, TL-LUEn and TL-LUE performed better than MOD17 for all vegetation types except crops at the half-hourly scale. At the daily and 8-day scales, both TL-LUEn and TL-LUE outperformed MOD17 for forests. However, TL-LUEn had a mixed performance for the three non-forest types while TL-LUE outperformed MOD17 slightly for all these non-forest types at daily and 8-day scales. The better performance of TL-LUEn and TL-LUE for forests was mainly achieved by the correction of the underestimation/overestimation of GPP simulated by MOD17 under low/high solar radiation and sky clearness conditions. TL-LUEn is more applicable at individual sites at the half-hourly scale while TL-LUE could be regionally used at half-hourly, daily and 8-day scales. MOD17 is also an applicable option regionally at the 8-day scale.« less

Performance of Linear and Nonlinear Two-Leaf Light Use Efficiency Models at Different Temporal Scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Xiaocui; Ju, Weimin; Zhou, Yanlian

The reliable simulation of gross primary productivity (GPP) at various spatial and temporal scales is of significance to quantifying the net exchange of carbon between terrestrial ecosystems and the atmosphere. This study aimed to verify the ability of a nonlinear two-leaf model (TL-LUEn), a linear two-leaf model (TL-LUE), and a big-leaf light use efficiency model (MOD17) to simulate GPP at half-hourly, daily and 8-day scales using GPP derived from 58 eddy-covariance flux sites in Asia, Europe and North America as benchmarks. Model evaluation showed that the overall performance of TL-LUEn was slightly but not significantly better than TL-LUE at half-hourlymore » and daily scale, while the overall performance of both TL-LUEn and TL-LUE were significantly better (p < 0.0001) than MOD17 at the two temporal scales. The improvement of TL-LUEn over TL-LUE was relatively small in comparison with the improvement of TL-LUE over MOD17. However, the differences between TL-LUEn and MOD17, and TL-LUE and MOD17 became less distinct at the 8-day scale. As for different vegetation types, TL-LUEn and TL-LUE performed better than MOD17 for all vegetation types except crops at the half-hourly scale. At the daily and 8-day scales, both TL-LUEn and TL-LUE outperformed MOD17 for forests. However, TL-LUEn had a mixed performance for the three non-forest types while TL-LUE outperformed MOD17 slightly for all these non-forest types at daily and 8-day scales. The better performance of TL-LUEn and TL-LUE for forests was mainly achieved by the correction of the underestimation/overestimation of GPP simulated by MOD17 under low/high solar radiation and sky clearness conditions. TL-LUEn is more applicable at individual sites at the half-hourly scale while TL-LUE could be regionally used at half-hourly, daily and 8-day scales. MOD17 is also an applicable option regionally at the 8-day scale.« less

Transient analysis of unbalanced short circuits of the ERDA-NASA 100 kW wind turbine alternator

NASA Technical Reports Server (NTRS)

Hwang, H. H.; Gilbert, L. J.

1976-01-01

Unbalanced short-circuit faults on the alternator of the ERDA-NASA Mod-O100-kW experimental wind turbine are studied. For each case, complete solutions for armature, field, and damper-circuit currents; short-circuit torque; and open-phase voltage are derived directly by a mathematical analysis. Formulated results are tabulated. For the Mod-O wind turbine alternator, numerical calculations are given, and results are presented by graphs. Comparisons for significant points among the more important cases are summarized. For these cases the transients are found to be potentially severe. The effect of the alternator neutral-to-ground impedance is evaluated.

Efficacy of Genetically Modified Bt Toxins Alone and in Combinations Against Pink Bollworm Resistant to Cry1Ac and Cry2Ab

PubMed Central

Tabashnik, Bruce E.; Fabrick, Jeffrey A.; Unnithan, Gopalan C.; Yelich, Alex J.; Masson, Luke; Zhang, Jie; Bravo, Alejandra; Soberón, Mario

2013-01-01

Evolution of resistance in pests threatens the long-term efficacy of insecticidal proteins from Bacillus thuringiensis (Bt) used in sprays and transgenic crops. Previous work showed that genetically modified Bt toxins Cry1AbMod and Cry1AcMod effectively countered resistance to native Bt toxins Cry1Ab and Cry1Ac in some pests, including pink bollworm (Pectinophora gossypiella). Here we report that Cry1AbMod and Cry1AcMod were also effective against a laboratory-selected strain of pink bollworm resistant to Cry2Ab as well as to Cry1Ab and Cry1Ac. Resistance ratios based on the concentration of toxin killing 50% of larvae for the resistant strain relative to a susceptible strain were 210 for Cry2Ab, 270 for Cry1Ab, and 310 for Cry1Ac, but only 1.6 for Cry1AbMod and 2.1 for Cry1AcMod. To evaluate the interactions among toxins, we tested combinations of Cry1AbMod, Cry1Ac, and Cry2Ab. For both the resistant and susceptible strains, the net results across all concentrations tested showed slight but significant synergism between Cry1AbMod and Cry2Ab, whereas the other combinations of toxins did not show consistent synergism or antagonism. The results suggest that the modified toxins might be useful for controlling populations of pink bollworm resistant to Cry1Ac, Cry2Ab, or both. PMID:24244692

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Antonelli, M. (Editor)

1982-01-01

Activities performed on Mod I engine testing and test results; the manufacture, assembly, and test of a Mod I engine in the United States; design initiation of the Mod I-A engine system; transient performance testing; Stirling reference engine manufacturing and reduced size studies; components and subsystems; and the study and test of low cost alloys are summarized.

The Imaging Modulography Technique Revisited for High-Definition Intravascular Ultrasound: Theoretical Framework.

PubMed

Tacheau, Antoine; Le Floc'h, Simon; Finet, Gérard; Doyley, Marvin M; Pettigrew, Roderic I; Cloutier, Guy; Ohayon, Jacques

2016-03-01

Mechanical characterization of atherosclerotic lesions remains an essential step for the detection of vulnerable plaques (VPs). Recently, an intravascular ultrasound (IVUS) elasticity reconstruction method (iMOD) has been tested in vivo by our group. The major limitation of iMOD is the need to estimate the strain field in the entire VP despite attenuated depth penetration signals when using high-definition (HD) IVUS systems. Therefore, an extended iMOD approach (E-iMOD) was designed and applied to coronary lesions of patients imaged in vivo with IVUS. The E-iMOD method (i) quantified necrotic core areas with a mean absolute relative error of 3.5 ± 3.5% and (ii) identified Young's moduli of the necrotic cores and fibrous regions with mean values of 5.7 ± 0.8 kPa and 794.5 ± 22.0 kPa instead of 5 kPa and 800 kPa, respectively. This study demonstrates the potential of the improved HD-IVUS modulography technique E-iMOD to characterize coronary VPs. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. All rights reserved.

Rapid, Efficient Detection and Drug Susceptibility Testing of Mycobacterium tuberculosis in Sputum by Microscopic Observation of Broth Cultures

PubMed Central

Caviedes, Luz; Lee, Tien-Shun; Gilman, Robert H.; Sheen, Patricia; Spellman, Emily; Lee, Ellen H.; Berg, Douglas E.; Montenegro-James, Sonia

2000-01-01

Inexpensive, rapid, and reliable methods of detecting infection by and drug susceptibility of Mycobacterium tuberculosis (MTB) are crucial to the control of tuberculosis. The novel microscopic observation broth-drug susceptibility assay (MODS) detects early growth of MTB in liquid medium, allowing more timely diagnosis and drug susceptibility testing. Sputum samples from hospitalized patients in Peru were analyzed by using stains, culture, and PCR. Sensitivity of MODS (92%) compared favorably with the most sensitive of the other culture methods (93%). Sputum samples positive for tuberculosis were tested for susceptibility to isoniazid and rifampin with the microwell alamar blue assay (MABA) and MODS. In 89% of cases, there was concordance between MODS and MABA. Of the diagnostic and susceptibility testing methods used, MODS yielded results most rapidly (median, 9.0 and 9.5 days, respectively). MODS is a rapid, inexpensive, sensitive, and specific method for MTB detection and susceptibility testing; it is particularly appropriate for use in developing countries burdened by significant infection rates and increasing numbers of multiple-drug-resistant cases. PMID:10699023

Rapid, efficient detection and drug susceptibility testing of Mycobacterium tuberculosis in sputum by microscopic observation of broth cultures. The Tuberculosis Working Group in Peru.

PubMed

Caviedes, L; Lee, T S; Gilman, R H; Sheen, P; Spellman, E; Lee, E H; Berg, D E; Montenegro-James, S

2000-03-01

Inexpensive, rapid, and reliable methods of detecting infection by and drug susceptibility of Mycobacterium tuberculosis (MTB) are crucial to the control of tuberculosis. The novel microscopic observation broth-drug susceptibility assay (MODS) detects early growth of MTB in liquid medium, allowing more timely diagnosis and drug susceptibility testing. Sputum samples from hospitalized patients in Peru were analyzed by using stains, culture, and PCR. Sensitivity of MODS (92%) compared favorably with the most sensitive of the other culture methods (93%). Sputum samples positive for tuberculosis were tested for susceptibility to isoniazid and rifampin with the microwell alamar blue assay (MABA) and MODS. In 89% of cases, there was concordance between MODS and MABA. Of the diagnostic and susceptibility testing methods used, MODS yielded results most rapidly (median, 9.0 and 9.5 days, respectively). MODS is a rapid, inexpensive, sensitive, and specific method for MTB detection and susceptibility testing; it is particularly appropriate for use in developing countries burdened by significant infection rates and increasing numbers of multiple-drug-resistant cases.

Une modélisation de haut niveau des stratégies d'écriture motrice d'enfants en scolarité primaire : approche bayésienne

NASA Astrophysics Data System (ADS)

Zaarour, I.; El-Eter, B.; Leray, P.; Heutte, L.; Labiche, J.; Mellier, D.; Zoaeter, M.

2005-05-01

L'objectif de cette étude est de découvrir des stratégies d'écriture motrices des enfants en scolarité primaire en adoptant un modèle graphique probabiliste (réseaux bayésiens). Nous représentons une stratégie d'écriture par une variable cachée et nous construisons ainsi un modèle global hiérarchique pour pouvoir lier les stratégies locales aux stratégies globales et modéliser la dépendance probabiliste entre variables et stratégies. Ce modèle hiérarchique, appris à partir des données réelles, nous a permis de découvrir des stratégies consistantes et robustes. Ces résultats nous a permis de favoriser une modélisation temporelle et dynamique des stratégies d'écriture motrices indépendantes de l'âge scolaire.

Considerations on the Use of Custom Accelerators for Big Data Analytics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castellana, Vito G.; Tumeo, Antonino; Minutoli, Marco

Accelerators, including Graphic Processing Units (GPUs) for gen- eral purpose computation, many-core designs with wide vector units (e.g., Intel Phi), have become a common component of many high performance clusters. The appearance of more stable and reliable tools tools that can automatically convert code written in high-level specifications with annotations (such as C or C++) to hardware de- scription languages (High-Level Synthesis - HLS), is also setting the stage for a broader use of reconfigurable devices (e.g., Field Pro- grammable Gate Arrays - FPGAs) in high performance system for the implementation of custom accelerators, helped by the fact that newmore » processors include advanced cache-coherent interconnects for these components. In this chapter, we briefly survey the status of the use of accelerators in high performance systems targeted at big data analytics applications. We argue that, although the progress in the use of accelerators for this class of applications has been sig- nificant, differently from scientific simulations there still are gaps to close. This is particularly true for the ”irregular” behaviors exhibited by no-SQL, graph databases. We focus our attention on the limits of HLS tools for data analytics and graph methods, and discuss a new architectural template that better fits the requirement of this class of applications. We validate the new architectural templates by mod- ifying the Graph Engine for Multithreaded System (GEMS) frame- work to support accelerators generated with such a methodology, and testing with queries coming from the Lehigh University Benchmark (LUBM). The architectural template enables better supporting the task and memory level parallelism present in graph methods by sup- porting a new control model and a enhanced memory interface. We show that out solution allows generating parallel accelerators, pro- viding speed ups with respect to conventional HLS flows. We finally draw conclusions and present a perspective on the use of reconfig- urable devices and Design Automation tools for data analytics.« less

Identification of wheat varieties with a parallel-plate capacitance sensor using fisher linear discriminant analysis

USDA-ARS?s Scientific Manuscript database

Fisher’s linear discriminant (FLD) models for wheat variety classification were developed and validated. The inputs to the FLD models were the capacitance (C), impedance (Z), and phase angle ('), measured at two frequencies. Classification of wheat varieties was obtained as output of the FLD mod...

The feasibility of determining the effectiveness and cost-effectiveness of medication organisation devices compared with usual care for older people in a community setting: systematic review, stakeholder focus groups and feasibility randomised controlled trial.

PubMed

Bhattacharya, Debi; Aldus, Clare F; Barton, Garry; Bond, Christine M; Boonyaprapa, Sathon; Charles, Ian S; Fleetcroft, Robert; Holland, Richard; Jerosch-Herold, Christina; Salter, Charlotte; Shepstone, Lee; Walton, Christine; Watson, Steve; Wright, David J

2016-07-01

Medication organisation devices (MODs) provide compartments for a patient's medication to be organised into the days of the week and the recommended times the medication should be taken. To define the optimal trial design for testing the clinical effectiveness and cost-effectiveness of MODs. The feasibility study comprised a systematic review and focus groups to inform a randomised controlled trial (RCT) design. The resulting features were tested on a small scale, using a 2 × 2 factorial design to compare MODs with usual packaging and to compare weekly with monthly supply. The study design was then evaluated. Potential participants were identified by medical practices. Aged over 75 years, prescribed at least three solid oral dosage form medications, unintentionally non-adherent and self-medicating. Participants were excluded if deemed by their health-care team to be unsuitable. One of three MODs widely used in routine clinical practice supplied either weekly or monthly. To identify the most effective method of participant recruitment, to estimate the prevalence of intentional and unintentional non-adherence in an older population, to provide a point estimate of the effect size of MODs relative to usual care and to determine the feasibility and acceptability of trial participation. The systematic review included MOD studies of any design reporting medication adherence, health and social outcomes, resource utilisation or dispensing or administration errors. Focus groups with patients, carers and health-care professionals supplemented the systematic review to inform the RCT design. The resulting design was implemented and then evaluated through questionnaires and group discussions with participants and health-care professionals involved in trial delivery. Studies on MODs are largely of poor quality. The relationship between adherence and health outcomes is unclear. Of the limited studies reporting health outcomes, some reported a positive relationship while some reported increased hospitalisations associated with MODs. The pre-trial focus groups endorsed the planned study design, but suggested a minimum recruitment age of 50-60 years. A total of 35.4% of patients completing the baseline questionnaire were excluded because they already used a MOD. Active recruitment yielded a higher consent rate, but passive recruitment was more cost-effective. The prevalence of intentional non-adherence was 24.7% [n = 71, 95% confidence interval (CI) 19.7% to 29.6%] of participants. Of the remaining 76 participants, 46.1% (95% CI 34.8% to 57.3%) were unintentionally non-adherent. There was no indication of a difference in adherence between the study arms. Participants reported a high level of satisfaction with the design. Five adverse/serious adverse events were identified in the MOD study arms and none was identified in the control arms. There was no discernible difference in health economic outcomes between the four study arms; the mean intervention cost was £20 per month greater for MOD monthly relative to usual supply monthly. MOD provision to unintentionally non-adherent older people may cause medication-related adverse events. The primary outcome for a definitive MOD trial should be health outcomes. Such a trial should recruit patients by postal invitation and recruit younger patients. A study examining the association between MOD initiation and adverse effects is necessary and a strategy to safely introduce MODs should be explored. A definitive study testing the clinical effectiveness and cost-effectiveness of MODs is also required. Current Controlled Trials ISRCTN 30626972 and UKCRN 12739. This project was funded by National Institute for Health Research (NIHR) Health Technology Assessment Programme and will be published in full in Health Technology Assessment; Vol. 20, No. 50. See the NIHR Journals Library website for further project information.

ICRF mode conversion in three-ion species heating experiment and in flow drive experiment on the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Lin, Y.; Wukitch, S. J.; Edlund, E.; Ennever, P.; Hubbard, A. E.; Porkolab, M.; Rice, J.; Wright, J.

2017-10-01

In recent three-ion species (majority D and H plus a trace level of 3He) ICRF heating experiments on Alcator C-Mod, double mode conversion on both sides of the 3He cyclotron resonance has been observed using the phase contrast imaging (PCI) system. The MC locations are used to estimate the species concentrations in the plasma. Simulation using TORIC shows that with the 3He level <1%, most RF power is absorbed by the 3He ions and the process can generate energetic 3He ions. In mode conversion (MC) flow drive experiment in D(3He) plasma at 8 T, MC waves were also monitored by PCI. The MC ion cyclotron wave (ICW) amplitude and wavenumber kR have been found to correlate with the flow drive force. The MC efficiency, wave-number k of the MC ICW and their dependence on plasma parameters like Te0 have been studied. Based on the experimental observation and numerical study of the dispersion solutions, a hypothesis of the flow drive mechanism has been proposed.

Mode conversion in ICRF experiments on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Lin, Y.; Wukitch, S. J.; Edlund, E.; Ennever, P.; Hubbard, A. E.; Porkolab, M.; Rice, J.; Wright, J.

2017-10-01

In recent three-ion species (majority D and H plus a trace level of 3He) ICRF heating experiment on Alcator C-Mod, double mode conversion on both sides of the 3He cyclotron resonance has been observed using the phase contrast imaging (PCI) system. The MC locations are used to estimate the species concentrations in the plasma. Simulation using TORIC shows that with the 3He level <1%, most RF power is absorbed by the 3He ions and the process can generate energetic 3He ions. In recent mode conversion flow drive experiment in D(3He) plasma at 8 T, MC waves were also monitored by PCI. The MC ion cyclotron wave (ICW) amplitude and wavenumber kR have been found to correlate with the flow drive force. The MC efficiency, wave-number k of the MC ICW and their dependence on plasma parameters like Te0 are shown to play important roles. Based on the experimental observation and numerical study of the dispersion solutions, a hypothesis of the flow drive mechanism has been proposed. Supported by USDoE awards DE-FC02-99ER54512.

Relationship between frequency power spectra and intermittent, large-amplitude bursts in the Alcator C-Mod scrape-off layer

NASA Astrophysics Data System (ADS)

Theodorsen, A.; Garcia, O. E.; Kube, R.; LaBombard, B.; Terry, J. L.

2017-11-01

Fluctuations in the boundary region of the Alcator C-Mod tokamak have been analyzed using gas puff imaging data from a set of Ohmically heated plasma density scan experiments. It is found that the relative fluctuation amplitudes are modest and close to normally distributed at the separatrix but become increasingly larger and skewed towards the main chamber wall. The frequency power spectra are nevertheless similar for all radial positions and line-averaged densities. Predictions of a stochastic model, describing the plasma fluctuations as a super-position of uncorrelated pulses, are shown to be in excellent agreement with the measurements. This implies that the pulse duration is the same, while the degree of pulse overlap decreases radially outwards in the scrape-off layer. The universal frequency power spectral density is thus determined by the shape and duration of the large-amplitude bursts associated with blob-like structures. The model also describes the rate of threshold level crossings, for which the exponential tails underline the intermittency of the fluctuations in the far scarpe-off layer.

Ohmic ITBs in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Fiore, C. L.; Rowan, W. L.; Dominguez, A.; Hubbard, A. E.; Ince-Cushman, A.; Greenwald, M. J.; Lin, L.; Marmar, E. S.; Reinke, M.; Rice, J. E.; Zhurovich, K.

2007-11-01

Internal transport barrier plasmas can arise spontaneously in ohmic Alcator C-Mod plasmas where an EDA H-mode has been developed by magnetic field ramping. These ohmic ITBs share the hallmarks of ITBs created with off-axis ICRF injection in that they have highly peaked density and pressure profiles and the peaking can be suppressed by on-axis ICRF. There is a reduction of particle and thermal flux in the barrier region which then allows the neoclassical pinch to peak the central density. Recent work on ITB onset conditions [1] which was motivated by turbulence studies [2] points to the broadening of the Ti profile with off-axis ICRF acting to reduce the ion temperature gradient. This suppresses ITG instability driven particle fluxes, which is thought to be the primary mechanism for ITB formation. The object of this study is to examine the characteristics of ohmic ITBs to find whether the stability of plasmas and the plasma parameters support the onset model. [1]K. Zhurovich, et al., To be published in Nuclear Fusion [2] D. R. Ernst, et al., Phys. Plasmas 11, 2637 (2004)

Study of the L-mode tokamak plasma “shortfall” with local and global nonlinear gyrokinetic δf particle-in-cell simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chowdhury, J.; Wan, Weigang; Chen, Yang

2014-11-15

The δ f particle-in-cell code GEM is used to study the transport “shortfall” problem of gyrokinetic simulations. In local simulations, the GEM results confirm the previously reported simulation results of DIII-D [Holland et al., Phys. Plasmas 16, 052301 (2009)] and Alcator C-Mod [Howard et al., Nucl. Fusion 53, 123011 (2013)] tokamaks with the continuum code GYRO. Namely, for DIII-D the simulations closely predict the ion heat flux at the core, while substantially underpredict transport towards the edge; while for Alcator C-Mod, the simulations show agreement with the experimental values of ion heat flux, at least within the range of experimental error.more » Global simulations are carried out for DIII-D L-mode plasmas to study the effect of edge turbulence on the outer core ion heat transport. The edge turbulence enhances the outer core ion heat transport through turbulence spreading. However, this edge turbulence spreading effect is not enough to explain the transport underprediction.« less

Preventing and Treating Hypoxia: Using a Physiology Simulator to Demonstrate the Value of Pre-Oxygenation and the Futility of Hyperventilation.

PubMed

Lerant, Anna A; Hester, Robert L; Coleman, Thomas G; Phillips, William J; Orledge, Jeffrey D; Murray, W Bosseau

2015-01-01

Insufficient pre-oxygenation before emergency intubation, and hyperventilation after intubation are mistakes that are frequently observed in and outside the operating room, in clinical practice and in simulation exercises. Physiological parameters, as appearing on standard patient monitors, do not alert to the deleterious effects of low oxygen saturation on coronary perfusion, or that of low carbon dioxide concentrations on cerebral perfusion. We suggest the use of HumMod, a computer-based human physiology simulator, to demonstrate beneficial physiological responses to pre-oxygenation and the futility of excessive minute ventilation after intubation. We programmed HumMod, to A.) compare varying times (0-7 minutes) of pre-oxygenation on oxygen saturation (SpO2) during subsequent apnoea; B.) simulate hyperventilation after apnoea. We compared the effect of different minute ventilation rates on SpO2, acid-base status, cerebral perfusion and other haemodynamic parameters. A.) With no pre-oxygenation, starting SpO2 dropped from 98% to 90% in 52 seconds with apnoea. At the other extreme, following full pre-oxygenation with 100% O2 for 3 minutes or more, the SpO2 remained 100% for 7.75 minutes during apnoea, and dropped to 90% after another 75 seconds. B.) Hyperventilation, did not result in more rapid normalization of SpO2, irrespective of the level of minute ventilation. However, hyperventilation did cause significant decreases in cerebral blood flow (CBF). HumMod accurately simulates the physiological responses compared to published human studies of pre-oxygenation and varying post intubation minute ventilations, and it can be used over wider ranges of parameters than available in human studies and therefore available in the literature.

Preventing and Treating Hypoxia: Using a Physiology Simulator to Demonstrate the Value of Pre-Oxygenation and the Futility of Hyperventilation

PubMed Central

Lerant, Anna A.; Hester, Robert L.; Coleman, Thomas G.; Phillips, William J.; Orledge, Jeffrey D.; Murray, W. Bosseau

2015-01-01

Introduction: Insufficient pre-oxygenation before emergency intubation, and hyperventilation after intubation are mistakes that are frequently observed in and outside the operating room, in clinical practice and in simulation exercises. Physiological parameters, as appearing on standard patient monitors, do not alert to the deleterious effects of low oxygen saturation on coronary perfusion, or that of low carbon dioxide concentrations on cerebral perfusion. We suggest the use of HumMod, a computer-based human physiology simulator, to demonstrate beneficial physiological responses to pre-oxygenation and the futility of excessive minute ventilation after intubation. Methods: We programmed HumMod, to A.) compare varying times (0-7 minutes) of pre-oxygenation on oxygen saturation (SpO2) during subsequent apnoea; B.) simulate hyperventilation after apnoea. We compared the effect of different minute ventilation rates on SpO2, acid-base status, cerebral perfusion and other haemodynamic parameters. Results: A.) With no pre-oxygenation, starting SpO2 dropped from 98% to 90% in 52 seconds with apnoea. At the other extreme, following full pre-oxygenation with 100% O2 for 3 minutes or more, the SpO2 remained 100% for 7.75 minutes during apnoea, and dropped to 90% after another 75 seconds. B.) Hyperventilation, did not result in more rapid normalization of SpO2, irrespective of the level of minute ventilation. However, hyperventilation did cause significant decreases in cerebral blood flow (CBF). Conclusions: HumMod accurately simulates the physiological responses compared to published human studies of pre-oxygenation and varying post intubation minute ventilations, and it can be used over wider ranges of parameters than available in human studies and therefore available in the literature. PMID:26283881

Effects of insulin combined with ethyl pyruvate on inflammatory response and oxidative stress in multiple-organ dysfunction syndrome rats with severe burns.

PubMed

Wang, Zhanke; Chen, Rongjian; Zhu, Zhongzhen; Zhang, Xiaoyun; Wang, Shiliang

2016-11-01

Inflammation response and oxidative stress promote the occurrence and development of multiple-organ dysfunction syndrome (MODS). Eighty MODS rats with third-degree burns were divided randomly into 4 groups: insulin, ethyl pyruvate (EP), insulin combined with EP, and control. Blood levels of glucose, alanine aminotransferase (ALT), creatine (CRE), creatine kinase (CK), tumor necrosis factor α (TNF-α), high-mobility group box 1 (HMGB-1), malondialdehyde (MDA), and total antioxidant capacity (TAC) before as well as 1, 3, 5, and 7 days after burns were measured. Blood levels of ALT, CRE, CK, TNF-α, HMGB-1, and MDA in INS, EP, and INS+EP groups at different time points were significantly lower, and TAC was significantly higher than that in the control group (C) (P<.01). These parameters in the INS+EP group were significantly lower, and TAC was significantly higher than that in INS and EP groups (P<.01). Blood levels of TNF-α, HMGB-1, and TAC in the INS group at different time points after burns were significantly lower, and MDA was significantly higher than that in the EP group (P<.01). Insulin combined with EP can effectively reduce the inflammatory response, oxidative stress, and main organ dysfunctions in MODS rats after severe burns. The therapeutic effect of insulin combined with EP is superior to single-agent treatment. The insulin anti-inflammatory effect is better than that of pyruvic acid ethyl ester, and the ethyl pyruvate antioxidation effect is better than that of insulin. The insulin can treat inflammation, whereas EP can reduce oxidative stress in MODS rats. Copyright © 2016 Elsevier Inc. All rights reserved.

MOD-2 wind turbine development

NASA Technical Reports Server (NTRS)

Gordon, L. H.; Andrews, J. S.; Zimmerman, D. K.

1983-01-01

The development of the Mod-2 turbine, designed to achieve a cost of electricity for the 100th production unit that will be competitive with conventional electric power generation is discussed. The Mod-2 wind turbine system (WTS) background, project flow, and a chronology of events and problem areas leading to Mod-2 acceptance are addressed. The role of the participating utility during site preparation, turbine erection and testing, remote operation, and routine operation and maintenance activity is reviewed. The technical areas discussed pertain to system performance, loads, and controls. Research and technical development of multimegawatt turbines is summarized.

High speed production of YBCO precursor films by advanced TFA-MOD process

NASA Astrophysics Data System (ADS)

Ichikawa, H.; Nakaoka, K.; Miura, M.; Sutoh, Y.; Nakanishi, T.; Nakai, A.; Yoshizumi, M.; Izumi, T.; Shiohara, Y.

2009-10-01

YBa 2Cu 3O 7-y (YBCO) long tapes derived from the metal-organic deposition (MOD) method using the starting solution containing trifluoroacetate (TFA) have been developed with high critical currents ( I c) over 200 A/cm-width. However, high speed production of YBCO films is simultaneously necessary to satisfy the requirements of electric power device applications in terms of cost and the amounts of the tapes. In this work, we developed a new TFA-MOD starting solution using F-free salt of Y, TFA salt of Ba and Cu-Octylate for application to the coating/calcination process and discussed several issues by using the Multi-turn (MT) Reel-to-Reel (RTR) system calcination furnace for the purpose of high throughput without degradation of the properties. The coating system was improved for uniform deposition qualities in both longitudinal and transversal directions. YBCO films using the new starting solution at the traveling rate of 10 m/h in coating/calcination by the MT-RTR calcination furnace showed the values of the critical current density of 1.6 MA/cm 2 as thick as 1.5 μm at 77 K under the self fields after firing at the high heating rate in the crystallization.

Dual-angle, self-calibrating Thomson scattering measurements in RFX-MOD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giudicotti, L., E-mail: leonardo.giudicotti@unipd.it; Department of Industrial Engineering, Padova University, Via Gradenigo 6/a, 35131 Padova; Pasqualotto, R.

2014-11-15

In the multipoint Thomson scattering (TS) system of the RFX-MOD experiment the signals from a few spatial positions can be observed simultaneously under two different scattering angles. In addition the detection system uses optical multiplexing by signal delays in fiber optic cables of different length so that the two sets of TS signals can be observed by the same polychromator. Owing to the dependence of the TS spectrum on the scattering angle, it was then possible to implement self-calibrating TS measurements in which the electron temperature T{sub e}, the electron density n{sub e} and the relative calibration coefficients of spectralmore » channels sensitivity C{sub i} were simultaneously determined by a suitable analysis of the two sets of TS data collected at the two angles. The analysis has shown that, in spite of the small difference in the spectra obtained at the two angles, reliable values of the relative calibration coefficients can be determined by the analysis of good S/N dual‑angle spectra recorded in a few tens of plasma shots. This analysis suggests that in RFX-MOD the calibration of the entire set of TS polychromators by means of the similar, dual-laser (Nd:YAG/Nd:YLF) TS technique, should be feasible.« less

NetMOD Version 2.0 User?s Manual.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion J.

2015-10-01

NetMOD ( Net work M onitoring for O ptimal D etection) is a Java-based software package for conducting simulation of seismic, hydracoustic, and infrasonic networks. Specifically, NetMOD simulates the detection capabilities of monitoring networks. Network simulations have long been used to study network resilience to station outages and to determine where additional stations are needed to reduce monitoring thresholds. NetMOD makes use of geophysical models to determine the source characteristics, signal attenuation along the path between the source and station, and the performance and noise properties of the station. These geophysical models are combined to simulate the relative amplitudes ofmore » signal and noise that are observed at each of the stations. From these signal-to-noise ratios (SNR), the probability of detection can be computed given a detection threshold. This manual describes how to configure and operate NetMOD to perform detection simulations. In addition, NetMOD is distributed with simulation datasets for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) International Monitoring System (IMS) seismic, hydroacoustic, and infrasonic networks for the purpose of demonstrating NetMOD's capabilities and providing user training. The tutorial sections of this manual use this dataset when describing how to perform the steps involved when running a simulation. ACKNOWLEDGEMENTS We would like to thank the reviewers of this document for their contributions.« less

The value of microscopic-observation drug susceptibility assay in the diagnosis of tuberculosis and detection of multidrug resistance.

PubMed

Sertel Şelale, Denİz; Uzun, Meltem

2018-01-01

Inexpensive, rapid, and reliable tests for detecting the presence and drug susceptibility of Mycobacterium tuberculosis complex (MTBC) are urgently needed to control the transmission of tuberculosis. In this study, we aimed to assess the accuracy and speed of the microscopic-observation drug susceptibility (MODS) assay in the identification of MTBC and detection of multidrug resistance. Sputum samples from patients suspected to have tuberculosis were simultaneously tested with MODS and conventional culture [Löwenstein-Jensen (LJ) culture, BACTEC MGIT™ 960 (MGIT) system], and drug susceptibility testing (MGIT system) methods. A total of 331 sputum samples were analyzed. Sensitivity and specificity of MODS assay for detection of MTBC strains were 96% and 98.8%, respectively. MODS assay detected multidrug resistant MTBC isolates with 92.3% sensitivity and 96.6% specificity. Median time to culture positivity was similar for MGIT (8 days) and MODS culture (8 days), but was significantly longer with LJ culture (20 days) (p < 0.0001 for both comparisons). Median time to availability of the susceptibility results was significantly (p < 0.0001) shorter with MODS assay (8 days) than MGIT system (20 days). In conclusion, MODS is an inexpensive and rapid test with good performance characteristics for direct diagnosis of tuberculosis and detection of multidrug resistance. © 2017 APMIS. Published by John Wiley & Sons Ltd.

Kynurenine–3–monooxygenase inhibition prevents multiple organ failure in rodent models of acute pancreatitis

PubMed Central

Mole, Damian J; Webster, Scott P; Uings, Iain; Zheng, Xiaozhong; Binnie, Margaret; Wilson, Kris; Hutchinson, Jonathan P; Mirguet, Olivier; Walker, Ann; Beaufils, Benjamin; Ancellin, Nicolas; Trottet, Lionel; Bénéton, Véronique; Mowat, Christopher G; Wilkinson, Martin; Rowland, Paul; Haslam, Carl; McBride, Andrew; Homer, Natalie ZM; Baily, James E; Sharp, Matthew GF; Garden, O James; Hughes, Jeremy; Howie, Sarah EM; Holmes, Duncan S; Liddle, John; Iredale, John P

2015-01-01

Acute pancreatitis (AP) is a common and devastating inflammatory condition of the pancreas that is considered to be a paradigm of sterile inflammation leading to systemic multiple organ dysfunction syndrome (MODS) and death1,2 Acute mortality from AP-MODS exceeds 20%3 and for those who survive the initial episode, their lifespan is typically shorter than the general population4. There are no specific therapies available that protect individuals against AP-MODS. Here, we show that kynurenine-3-monooxygenase (KMO), a key enzyme of tryptophan metabolism5, is central to the pathogenesis of AP-MODS. We created a mouse strain deficient for Kmo with a robust biochemical phenotype that protected against extrapancreatic tissue injury to lung, kidney and liver in experimental AP-MODS. A medicinal chemistry strategy based on modifications of the kynurenine substrate led to the discovery of GSK180 as a potent and specific inhibitor of KMO. The binding mode of the inhibitor in the active site was confirmed by X-ray co-crystallography at 3.2 Å resolution. Treatment with GSK180 resulted in rapid changes in levels of kynurenine pathway metabolites in vivo and afforded therapeutic protection against AP-MODS in a rat model of AP. Our findings establish KMO inhibition as a novel therapeutic strategy in the treatment of AP-MODS and open up a new area for drug discovery in critical illness. PMID:26752518

Identification of Bacillus thuringiensis Cry1AbMod binding-proteins from Spodoptera frugiperda.

PubMed

Martínez de Castro, Diana L; García-Gómez, Blanca I; Gómez, Isabel; Bravo, Alejandra; Soberón, Mario

2017-12-01

Bacillus thuringiensis Cry toxins are currently used for pest control in transgenic crops but evolution of resistance by the insect pests threatens the use of this technology. The Cry1AbMod toxin was engineered to lack the alpha helix-1 of the parental Cry1Ab toxin and was shown to counter resistance to Cry1Ab and Cry1Ac toxins in different insect species including the fall armyworm Spodoptera frugiperda. In addition, Cry1AbMod showed enhanced toxicity to Cry1Ab-susceptible S. frugiperda populations. To gain insights into the mechanisms of this Cry1AbMod-enhanced toxicity, we isolated the Cry1AbMod toxin binding proteins from S. frugiperda brush border membrane vesicles (BBMV), which were identified by pull-down assay and liquid chromatography-tandem mass spectrometry (LC-MS/MS). The LC-MS/MS results indicated that Cry1AbMod toxin could bind to four classes of aminopeptidase (N1, N3, N4 y N5) and actin, with the highest amino acid sequence coverage acquired for APN 1 and APN4. In addition to these proteins, we found other proteins not previously described as Cry toxin binding proteins. This is the first report that suggests the interaction between Cry1AbMod and APN in S. frugiperda. Copyright © 2017 Elsevier Inc. All rights reserved.

Pathophysiology of the gut and the microbiome in the host response

PubMed Central

Lyons, John D.; Coopersmith, Craig M.

2016-01-01

Objective To describe and summarize the data supporting the “gut” as the motor driving critical illness and multiple organ dysfunction syndrome (MODS) presented at the Eunice Kennedy Shriver National Institute of Child Health and Human Development MODS Workshop (March 26–27, 2015). Data Sources Summary of workshop keynote presentation. Study Selection Not applicable. Data Extraction Presented by an expert in the field, the data assessing the role of gastrointestinal dysfunction driving critical illness were described with a focus on identifying knowledge gaps and research priorities. Data Synthesis Summary of presentation and discussion supported and supplemented by relevant literature. Conclusions The understanding of gut dysfunction in critical illness has evolved greatly over time, and the gut is now often considered as the “motor” of critical illness. The association of the gut with critical illness is supported by both animal models and clinical studies. Initially, the association between gut dysfunction and critical illness focused primarily on bacterial translocation into the bloodstream. However, that work has evolved to include other gut-derived products causing distant injury via other routes (e.g. lymphatics). Additionally, alterations in the gut epithelium may be associated with critical illness and influence outcomes. Gut epithelial apoptosis, intestinal hyperpermeability and perturbations in the intestinal mucus layer have all been associated with critical illness. Finally, there is growing evidence that the intestinal microbiome plays a crucial role in mediating pathology in critical illness. Further research is needed to better understand the role of each of these mechanisms and their contribution to MODS in children. PMID:28248833

Lower Hybrid wave edge power loss quantification on the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Faust, I. C.

2015-11-01

For the first time, the power deposition of Lower Hybrid RF waves into the edge plasma of a diverted tokamak has been systematically quantified. Edge deposition represents a parasitic loss of power that can greatly impact the use and efficiency of Lower Hybrid Current Drive (LHCD) at reactor-relevant densities. Through the use of a unique set of fast time resolution edge diagnostics, including innovative fast-thermocouples, an extensive set of Langmuir probes, and a Lyα ionization camera, the toroidal, poloidal and radial structure of the power deposition has been simultaneously determined. Power modulation was used to directly isolate the RF effects due to the prompt (t <τE) response of the scrape-off-layer (SOL) plasma to LHRF power. LHRF power was found to absorb more strongly in the edge at higher densities. It is found that a majority of this edge-deposited power is promptly conducted to the divertor. This correlates with the loss of current drive efficiency at high density previously observed on Alcator C-Mod, and displaying characteristics that contrast with the local RF edge absorption seen on other tokamaks. Measurements of ionization in the active divertor show dramatic changes due to LHRF power, implying that divertor region can be key for the LHRF edge power deposition physics. These observations support the existence a loss mechanism near the edge for LHRF at high density (ne > 1 . 0 .1020 [m-3]). Results will be shown addressing the distribution of power within the SOL, including the toroidal symmetry and radial distribution. These characteristics are important for deducing the cause of the reduced LHCD efficiency at high density and motivates the tailoring of wave propagation to minimize SOL interaction, for example, through the use of high-field-side launch. This work was performed on the Alcator C-Mod tokamak, a DoE Office of Science user facility, and is supported by USDoE award DE-FC02-99ER54512.

Interdisciplinary investigations in support of project DI-MOD

NASA Technical Reports Server (NTRS)

Starks, Scott A.

1991-01-01

Interdisciplinary investigations in support of project DI-MOD are discussed. The following subject areas were covered: (1) potential extensions of Project DI-MOD to additional sites in Central America; (2) human migration patterns and their impact on malaria transmission; and (3) an investigation into possible computer-based approaches to the analysis of remotely sensed multispectral data.

Only minor additional metabolic health benefits of high as opposed to moderate dose physical exercise in young, moderately overweight men.

PubMed

Reichkendler, M H; Rosenkilde, M; Auerbach, P L; Agerschou, J; Nielsen, M B; Kjaer, A; Hoejgaard, L; Sjödin, A; Ploug, T; Stallknecht, B

2014-05-01

The dose-response effects of exercise training on insulin sensitivity, metabolic risk, and quality of life were examined. Sixty-one healthy, sedentary (VO₂max: 35 ± 5 ml/kg/min), moderately overweight (BMI: 27.9 ± 1.8), young (age: 29 ± 6 years) men were randomized to sedentary living (sedentary control group; n = 18), moderate (moderate dose training group [MOD]: 300 kcal/day, n = 21), or high (high dose training group [HIGH]: 600 kcal/day, n = 22) dose physical exercise for 11 weeks. The return rate for post-intervention testing was 82-94% across groups. Weekly exercise amounted to 2,004 ± 24 and 3,774 ± 68 kcal, respectively, in MOD and HIGH. Cardiorespiratory fitness increased (P < 0.001) 18 ± 3% in MOD and 17 ± 3% in HIGH, and fat percentage decreased (P < 0.001) similarly in both exercise groups (MOD: 32 ± 1 to 29 ± 1%; HIGH: 30 ± 1 to 27 ± 1%). Peripheral insulin sensitivity increased (P < 0.01) (MOD: 28 ± 7%; HIGH: 36 ± 8%) and the homeostasis model assessment of insulin resistance decreased (P < 0.05) (MOD: -17 ± 7%; HIGH: -18 ± 10%). The number of subjects meeting the criteria of the metabolic syndrome decreased by 78% in MOD (P < 0.01) and by 80% in HIGH (P < 0.05). General health assessed by questionnaire increased similarly in MOD (P < 0.05) and HIGH (P < 0.01). Only minor additional health benefits were found when exercising ∼3,800 as opposed to ∼2,000 kcal/week in young moderately overweight men. This finding may have important public health implications. Copyright © 2012 The Obesity Society.

Early detection of nonneurologic organ failure in patients with severe traumatic brain injury: Multiple organ dysfunction score or sequential organ failure assessment?

PubMed

Ramtinfar, Sara; Chabok, Shahrokh Yousefzadeh; Chari, Aliakbar Jafari; Reihanian, Zoheir; Leili, Ehsan Kazemnezhad; Alizadeh, Arsalan

2016-10-01

The aim of this study is to compare the discriminant function of multiple organ dysfunction score (MODS) and sequential organ failure assessment (SOFA) components in predicting the Intensive Care Unit (ICU) mortality and neurologic outcome. A descriptive-analytic study was conducted at a level I trauma center. Data were collected from patients with severe traumatic brain injury admitted to the neurosurgical ICU. Basic demographic data, SOFA and MOD scores were recorded daily for all patients. Odd's ratios (ORs) were calculated to determine the relationship of each component score to mortality, and area under receiver operating characteristic (AUROC) curve was used to compare the discriminative ability of two tools with respect to ICU mortality. The most common organ failure observed was respiratory detected by SOFA of 26% and MODS of 13%, and the second common was cardiovascular detected by SOFA of 18% and MODS of 13%. No hepatic or renal failure occurred, and coagulation failure reported as 2.5% by SOFA and MODS. Cardiovascular failure defined by both tools had a correlation to ICU mortality and it was more significant for SOFA (OR = 6.9, CI = 3.6-13.3, P < 0.05 for SOFA; OR = 5, CI = 3-8.3, P < 0.05 for MODS; AUROC = 0.82 for SOFA; AUROC = 0.73 for MODS). The relationship of cardiovascular failure to dichotomized neurologic outcome was not significant statistically. ICU mortality was not associated with respiratory or coagulation failure. Cardiovascular failure defined by either tool significantly related to ICU mortality. Compared to MODS, SOFA-defined cardiovascular failure was a stronger predictor of death. ICU mortality was not affected by respiratory or coagulation failures.

Standardissimo. Les limitations théoriques du Modèle Standard. Quelles réponses y apporter?

NASA Astrophysics Data System (ADS)

Renard, F. M.

Nous présentons I 'état du Modèle Standard des interactions fortes, faibles et électromagnétiques. Après une description rapide de ses 3 secteurs, secteur de jauge (radiation), secteur fermionique (matière) et secteur scalaire (génération des masses), nous insistons sur le grand nombre de paramètres libres et sur les choix arbitraires qu'il a fallu faire dans l'élaboration du modèle. Nous faisons ressortir les problèmes techniques non résolus et nous dressons la liste des questions fondamentales restées sans réponses. Nous passons ensuite en revue les idées et méthodes proposées pour répondre à ces questions. Elles utilisent essentiellement 3 voies différentes. La première consiste à requérir plus de symétrie (extension du modèle, symétrie Gauche-Droite, Grandes Unifications, Supersymétrie,...). La seconde contient les diverses alternatives au Modèle Standard impliquant des modifications dans certains secteurs (par exemple le secteur scalaire avec le modèle de la Technicouleur) ou de façon plus violente l'hypothèse d'une sous-structure des leptons, des quarks et des bosons W et Z eux-mêmes. Une dernière voie cherche à justifier les particularités du Modèle Standard et relier ses paramètres libres en se basant sur des principes de cohérence interne du modèle. Les conséquences observables de ces diverses approches sont dans chaque cas mentionnées.

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

The major accomplishments were the completion of the Basic Stirling Engine (BSE) and the Stirling Engine System (SES) designs on schedule, the approval and acceptance of those designs by NASA, and the initiation of manufacture of BSE components. The performance predictions indicate the Mod II engine design will meet or exceed the original program goals of 30% improvement in fuel economy over a conventional Internal Combustion (IC) powered vehicle, while providing acceptable emissions. This was accomplished while simultaneously reducing Mod II engine weight to a level comparable with IC engine power density, and packaging the Mod II in a 1985 Celebrity with no external sheet metal changes. The projected mileage of the Mod II Celebrity for the combined urban and highway CVS cycle is 40.9 mpg which is a 32% improvement over the IC Celebrity. If additional potential improvements are verified and incorporated in the Mod II, the mileage could increase to 42.7 mpg.

Meteoroid/orbital debris impact damage predictions for the Russian space station MIR

NASA Technical Reports Server (NTRS)

Christiansen, E. L.; Hyde, J. L.; Lear, D.

1997-01-01

Components of the Mir space station have been exposed to the meteoroid/orbital debris (M/OD) environment for up to 11 years. During this period, no M/OD impact perforation of the pressure shell of the manned modules were reported. The NASA standard M/OD analysis code BUMPER was used to predict the probability of M/OD impact damage to various components of Mir. The analysis indicates a 1 in 2.2 chance that a M/OD impact would have caused a penetration resulting in a pressure leak of the Mir modules since its launch up to the February 1997. For the next five years, the estimated odds become 1 in 3. On an annual basis, penetration risks are 60 percent higher, on the average, in the next five years due to the larger size of Mir and the growth in the orbital debris population.

Sin1, a Mutation Affecting Female Fertility in Arabidopsis, Interacts with Mod1, Its Recessive Modifier

PubMed Central

Lang, J. D.; Ray, S.; Ray, A.

1994-01-01

In Arabidopsis thaliana, a mutation in the SIN1 gene causes aberrant ovule development and female-specific sterility. The effect of the sin1 mutation is polymorphic and pleiotropic in different genetic backgrounds. The polymorphism concerns morphology of the mutant ovules. The pleiotropism involves internodal distance and inflorescence initiation time. The particular ovule phenotype and the length of internodes are dependent on an interaction of sin1 with a second recessive gene, which we term mod1. The recessive mod1 allele in a homozygous sin1 mutant plant reduces internode length and ovule integument size. The mutation sin1, but not mod1, has a demonstrable effect on ovule morphology when acting idependently. In our crosses mod1 was inseparably linked to the well known mutation erecta that is known to cause a reduction in internode and pedicel lengths. PMID:7982564

Calcul numérique accéléré de mesures de performance sur les modèles Markoviens appliqués aux systèmes informatiques et de télécommunications

NASA Astrophysics Data System (ADS)

Ghaddar, A.; Sinno, N.

2005-05-01

La complexité du phénomène de files d'attente dans les systèmes informatiques et télécommunications nécessite leur simulation par des modèles Markoviens pour les mesures de performance, mesure des délais d'attente au niveau des routeurs pour le modèle informatique et l'étude de la gestion des appels téléphoniques pour le modèle des circuits téléphoniques. L'optimisation des méthodes numériques de résolution des équations relatives à ces deux modèles va permettre d' ídentifier les critères de convergence rapide vers les états stationnaires correspondant à ces mesures.

Hypervelocity Impact Testing of International Space Station Meteoroid/Orbital Debris Shielding Using an Inhibited Shaped Charge Launcher

NASA Technical Reports Server (NTRS)

Kerr, Justin H.; Grosch, Donald

2001-01-01

Engineers at the NASA Johnson Space Center have conducted hypervelocity impact (HVI) performance evaluations of spacecraft meteoroid and orbital debris (M/OD) shields at velocities in excess of 7 km/s. The inhibited shaped charge launcher (ISCL), developed by the Southwest Research Institute, launches hollow, circular, cylindrical jet tips to approximately 11 km/s. Since traditional M/OD shield ballistic limit performance is defined as the diameter of sphere required to just perforate or spall a spacecraft pressure wall, engineers must decide how to compare ISCL derived data with those of the spherical impactor data set. Knowing the mass of the ISCL impactor, an equivalent sphere diameter may be calculated. This approach is conservative since ISCL jet tips are more damaging than equal mass spheres. A total of 12 tests were recently conducted at the Southwest Research Institute (SWRI) on International Space Station M/OD shields. Results of these tests are presented and compared to existing ballistic limit equations. Modification of these equations is suggested based on the results.

The Aspin Plan: A Resource Allocation Strategy for Today

DTIC Science & Technology

1993-04-15

Subs." Wall Street Journal, 6 May 1992, p. A4. Roos, John G. "$59-Billion Armor Mod Plan Has Only One Tread on Ground". Armed Forces Journal...2i Pxa e R~C40 HAPILL,? 61TL..T1t& jaa C-ALMSLf-I ’PR 1-70 3-SOS- 6 _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3a. VJ.AME OF ý!JNDINGiSON,1SOR!tNG 308c OfC.. "’M3OL...accepted and implemented in a timely manner. In February 1992 Les Aspin, former Chairman of the House Armed Services Committee, outlined a resource

Feasibility Study for a Structurally Efficient, Multi-Modal Shelter Concept Utilizing Advanced Technology Production Techniques

DTIC Science & Technology

1974-02-01

II I~ x p:1 ns ion P roc cuurc Longitudin:-11 Section, Container Mod·c Configuration r Ex p :m s i on Pro c c d u r e Longitudinal Section...No . I II. I I I. IV. v. VI. VII. VIII. IX. X . XI. XII. XIII. XIV. XV . XVI. XVII . XVIII . XIX. XX. XXI. XXII . XXI II. XXIV...mat e rial s and examples from these categories . Glass Fibers Glass Mi c r os pheres As bestos Carbon Graphite Ce llulose Cotton Jute Rayo n

Tungsten Transport Protein A (WtpA) in Pyrococcus furiosus: the First Member of a New Class of Tungstate and Molybdate Transporters

PubMed Central

Bevers, Loes E.; Hagedoorn, Peter-Leon; Krijger, Gerard C.; Hagen, Wilfred R.

2006-01-01

A novel tungstate and molybdate binding protein has been discovered from the hyperthermophilic archaeon Pyrococcus furiosus. This tungstate transport protein A (WtpA) is part of a new ABC transporter system selective for tungstate and molybdate. WtpA has very low sequence similarity with the earlier-characterized transport proteins ModA for molybdate and TupA for tungstate. Its structural gene is present in the genome of numerous archaea and some bacteria. The identification of this new tungstate and molybdate binding protein clarifies the mechanism of tungstate and molybdate transport in organisms that lack the known uptake systems associated with the ModA and TupA proteins, like many archaea. The periplasmic protein of this ABC transporter, WtpA (PF0080), was cloned and expressed in Escherichia coli. Using isothermal titration calorimetry, WtpA was observed to bind tungstate (dissociation constant [KD] of 17 ± 7 pM) and molybdate (KD of 11 ± 5 nM) with a stoichiometry of 1.0 mol oxoanion per mole of protein. These low KD values indicate that WtpA has a higher affinity for tungstate than do ModA and TupA and an affinity for molybdate similar to that of ModA. A displacement titration of molybdate-saturated WtpA with tungstate showed that the tungstate effectively replaced the molybdate in the binding site of the protein. PMID:16952940

Inlay-retained cantilever fixed dental prostheses to substitute a single premolar: impact of zirconia framework design after dynamic loading.

PubMed

Shahin, Ramez; Tannous, Fahed; Kern, Matthias

2014-08-01

The purpose of this in-vitro study was to evaluate the influence of the framework design on the durability of inlay-retained cantilever fixed dental prostheses (IR-FDPs), made from zirconia ceramic, after artificial ageing. Forty-eight caries-free human premolars were prepared as abutments for all-ceramic cantilevered IR-FDPs using six framework designs: occlusal-distal (OD) inlay, OD inlay with an oral retainer wing, OD inlay with two retainer wings, mesial-occlusal-distal (MOD) inlay, MOD inlay with an oral retainer ring, and veneer partial coping with a distal box (VB). Zirconia IR-FDPs were fabricated via computer-aided design/computer-aided manufacturing (CAD/CAM) technology. The bonding surfaces were air-abraded (50 μm alumina/0.1 MPa), and the frameworks were bonded with adhesive resin cement. Specimens were stored for 150 d in a 37°C water bath during which they were thermocycled between 5 and 55°C for 37,500 cycles; thereafter, they were exposed to 600,000 cycles of dynamic loading with a 5-kg load in a chewing simulator. All surviving specimens were loaded onto the pontic and tested until failure using a universal testing machine. The mean failure load of the groups ranged from 260.8 to 746.7 N. Statistical analysis showed that both MOD groups exhibited significantly higher failure loads compared with the other groups (i.e. the three OD groups and the VB group) and that there was no significant difference in the failure load among the OD groups and the VB group. In conclusion, zirconia IR-FDPs with a modified design exhibited promising failure modes. © 2014 Eur J Oral Sci.

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 1

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. Volume 3, book 1 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation is described in detail.

Standing Up a Narcotic Confirmation Laboratory for the Russian Federation Ministry of Defense Nuclear Personnel Reliability Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

LukyanenkoMD, Victor; Eisele, Gerhard R; Coates, Cameron W

2010-01-01

Through a cooperative effort between the U. S. Department of Energy and the Russian Federation (RF) Ministry of Defense (MOD) a Personnel Reliability Program (PRP) for the nuclear handlers within the RF MOD has been implemented. A key element in the RF MOD PRP is the detection and confirmation of narcotic use in subject military and civilian personnel. This paper describes the process of narcotics screening and testing in the RF MOD and explains the confirmation process once screening has shown a positive result. Issues of laboratory certification, employee certification, employee training, sample chain-of-custody, and equipment needs will be addressed.

MODFLOW-2000, the U.S. Geological Survey modular ground-water model -- Documentation of MOD-PREDICT for predictions, prediction sensitivity analysis, and evaluation of uncertainty

USGS Publications Warehouse

Tonkin, M.J.; Hill, Mary C.; Doherty, John

2003-01-01

This document describes the MOD-PREDICT program, which helps evaluate userdefined sets of observations, prior information, and predictions, using the ground-water model MODFLOW-2000. MOD-PREDICT takes advantage of the existing Observation and Sensitivity Processes (Hill and others, 2000) by initiating runs of MODFLOW-2000 and using the output files produced. The names and formats of the MODFLOW-2000 input files are unchanged, such that full backward compatibility is maintained. A new name file and input files are required for MOD-PREDICT. The performance of MOD-PREDICT has been tested in a variety of applications. Future applications, however, might reveal errors that were not detected in the test simulations. Users are requested to notify the U.S. Geological Survey of any errors found in this document or the computer program using the email address available at the web address below. Updates might occasionally be made to this document, to the MOD-PREDICT program, and to MODFLOW- 2000. Users can check for updates on the Internet at URL http://water.usgs.gov/software/ground water.html/.

Surface thermocouples for measurement of pulsed heat flux in the divertor of the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, D.; LaBombard, B.

2012-03-01

A novel set of thermocouple sensors has been developed to measure heat fluxes arriving at divertor surfaces in the Alcator C-Mod tokamak, a magnetic confinement fusion experiment. These sensors operate in direct contact with the divertor plasma, which deposits heat fluxes in excess of ˜10 MW/m2 over an ˜1 s pulse. Thermoelectric EMF signals are produced across a non-standard bimetallic junction: a 50 μm thick 74% tungsten-26% rhenium ribbon embedded in a 6.35 mm diameter molybdenum cylinder. The unique coaxial geometry of the sensor combined with its single-point electrical ground contact minimizes interference from the plasma/magnetic environment. Incident heat fluxes are inferred from surface temperature evolution via a 1D thermal heat transport model. For an incident heat flux of 10 MW/m2, surface temperatures rise ˜1000 °C/s, corresponding to a heat flux flowing along the local magnetic field of ˜200 MW/m2. Separate calorimeter sensors are used to independently confirm the derived heat fluxes by comparing total energies deposited during a plasma pulse. Langmuir probes in close proximity to the surface thermocouples are used to test plasma-sheath heat transmission theory and to identify potential sources of discrepancies among physical models.

Break modeling for RELAP5 analyses of ISP-27 Bethsy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petelin, S.; Gortnar, O.; Mavko, B.

This paper presents pre- and posttest analyses of International Standard Problem (ISP) 27 on the Bethsy facility and separate RELAP5 break model tests considering the measured boundary condition at break inlet. This contribution also demonstrates modifications which have assured the significant improvement of model response in posttest simulations. Calculations were performed using the RELAP5/MOD2/36.05 and RELAP5/MOD3.5M5 codes on the MicroVAX, SUN, and CONVEX computers. Bethsy is an integral test facility that simulates a typical 900-MW (electric) Framatome pressurized water reactor. The ISP-27 scenario involves a 2-in. cold-leg break without HPSI and with delayed operator procedures for secondary system depressurization.

Houston, We Have a Problem Solving Model for Training

NASA Technical Reports Server (NTRS)

Schmidt, Lacey; Slack, Kelley; Keeton, Kathryn; Barshi, Immanuel; Martin, Lynne; Mauro, Robert; O'Keefe, William; Baldwin, Evelyn; Huning, Therese

2011-01-01

In late 2006, the Mission Operations Directorate (MOD) at NASA began looking at ways to make training more efficient for the flight controllers who support the International Space Station. The average certification times for flight controllers spanned from 18 months to three years and the MOD, responsible for technical training, was eager to develop creative solutions that would reduce the time to 12 months. Additionally, previously trained flight controllers sometimes participated in more than 50 very costly, eight-hour integrated simulations before becoming certified. New trainees needed to gain proficiency with far fewer lessons and training simulations than their predecessors. This poster presentation reviews the approach and the process that is currently in development to accomplish this goal.

Modélisation des charges d'espace dans les isolants solides par une analyse spectrale

NASA Astrophysics Data System (ADS)

Haas, V.; Scouarnec, Ch.; Franceschi, J. L.

1998-01-01

A mathematical method based on spectral algebra is developped for the thermal modulation method. These methods permit to measure the space charge distribution in solid insulators. The modelling presented permits to evaluate the performances and the limitations of the measurement method. Une linéarisation par l'algèbre spectrale a été développée dans une méthode de modulation thermique pour mesurer la distribution des charges électriques dans les isolants solides. La modélisation présentée permet d'évaluer les performances et les limites tant numériques que physiques de la méthode de mesure.

External excitation of a short-wavelength fluctuation in the Alcator C-Mod edge plasma and its relationship to the quasi-coherent mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golfinopoulos, T.; LaBombard, B.; Parker, R. R.

2014-05-15

A novel “Shoelace” antenna has been used to inductively excite a short-wavelength edge fluctuation in a tokamak boundary layer for the first time. The principal design parameters, k{sub ⊥}=1.5±0.1 cm{sup −1} and 45

Soil Quality under Riparian Forest at Different Stages of Ecological Succession and Cultivated with Sugarcane

NASA Astrophysics Data System (ADS)

Silva, Luiz Gabriel; Casagrande, José Carlos; Colato, Alexandre; Soares, Marcio Roberto; Perissatto Meneghin, Silvana

2014-05-01

This work aimed at evaluating the quality of the soil through its chemical, physical and microbiological attributes, using additive pondered model, as well as studying the characteristics of the linear method of combination of data, figures of merit (FoMs), the process of assigning weights and standard score functions, using measurements collected in three areas (two riparian forests and a commercial crop of sugarcane) in two soil types (Oxisol and Podzol) located on the dam shores of Sugar Mill Saint Lucia-Araras/SP. The soil was sampled in the depths of 0-0.2 and 0.2-0.4m, and was determined some of its chemical attributes (nutrient content and organic matter, cationic exchange capacity - CEC, etc.), physical (particle size distribution, density and porosity) and microbiological (microbial biomass and basal respiration). Two models were built, one containing two hierarchical levels of FoMs (Mod1), and another containing three levels (Mod2), in order to try to isolate FoMs highly correlated from each other within a top-level FoM. At FoMs of Mod1 were assigned various combinations of weights, and those of Mod2 were assigned weights from three methods, distribution from fixed value, classification and pair-wise comparison. In the Mod1, in virtually all combinations of weights used, values of Soil Quality Index (SQI) were superior in older forests, while the most recent forest presented the lowest SQI, for both types of soil. The variation of SQI values obtained from the sets of weights used also differed between the combinations tested, with the set of values of the ancient forest showing smaller amplitude. It could also be observed that the sets of values of Oxisol showed higher SQI and lower amplitude in relation to that of Podzol. It was observed that these facts are due mainly to the soil organic matter content (MO), which differs between the vegetations and soil types, and influences many parameters used in the model. Thus, in the structures where MO had greater weight, the values of SQI have tended to be more discrepant between the combinations with upper and lower level of MO. In the case of Mod2, regardless of the method of allocation of weight used, it has not been possible to find clear distinction among the three physiognomies used, despite having been detected clear difference between the two types of soil, with the higher values to those presenting the Oxisol and Podzol. This situation can lead to consideration of what might be more interesting to use various combinations of random weights that a specific combination chosen empirically.

Mod5 protein binds to tRNA gene complexes and affects local transcriptional silencing

PubMed Central

Pratt-Hyatt, Matthew; Pai, Dave A.; Haeusler, Rebecca A.; Wozniak, Glenn G.; Good, Paul D.; Miller, Erin L.; McLeod, Ian X.; Yates, John R.; Hopper, Anita K.; Engelke, David R.

2013-01-01

The tRNA gene-mediated (tgm) silencing of RNA polymerase II promoters is dependent on subnuclear clustering of the tRNA genes, but genetic analysis shows that the silencing requires additional mechanisms. We have identified proteins that bind tRNA gene transcription complexes and are required for tgm silencing but not required for gene clustering. One of the proteins, Mod5, is a tRNA modifying enzyme that adds an N6-isopentenyl adenosine modification at position 37 on a small number of tRNAs in the cytoplasm, although a subpopulation of Mod5 is also found in the nucleus. Recent publications have also shown that Mod5 has tumor suppressor characteristics in humans as well as confers drug resistance through prion-like misfolding in yeast. Here, we show that a subpopulation of Mod5 associates with tRNA gene complexes in the nucleolus. This association occurs and is required for tgm silencing regardless of whether the pre-tRNA transcripts are substrates for Mod5 modification. In addition, Mod5 is bound to nuclear pre-tRNA transcripts, although they are not substrates for the A37 modification. Lastly, we show that truncation of the tRNA transcript to remove the normal tRNA structure also alleviates silencing, suggesting that synthesis of intact pre-tRNAs is required for the silencing mechanism. These results are discussed in light of recent results showing that silencing near tRNA genes also requires chromatin modification. PMID:23898186

Kynurenine-3-monooxygenase inhibition prevents multiple organ failure in rodent models of acute pancreatitis.

PubMed

Mole, Damian J; Webster, Scott P; Uings, Iain; Zheng, Xiaozhong; Binnie, Margaret; Wilson, Kris; Hutchinson, Jonathan P; Mirguet, Olivier; Walker, Ann; Beaufils, Benjamin; Ancellin, Nicolas; Trottet, Lionel; Bénéton, Véronique; Mowat, Christopher G; Wilkinson, Martin; Rowland, Paul; Haslam, Carl; McBride, Andrew; Homer, Natalie Z M; Baily, James E; Sharp, Matthew G F; Garden, O James; Hughes, Jeremy; Howie, Sarah E M; Holmes, Duncan S; Liddle, John; Iredale, John P

2016-02-01

Acute pancreatitis (AP) is a common and devastating inflammatory condition of the pancreas that is considered to be a paradigm of sterile inflammation leading to systemic multiple organ dysfunction syndrome (MODS) and death. Acute mortality from AP-MODS exceeds 20% (ref. 3), and the lifespans of those who survive the initial episode are typically shorter than those of the general population. There are no specific therapies available to protect individuals from AP-MODS. Here we show that kynurenine-3-monooxygenase (KMO), a key enzyme of tryptophan metabolism, is central to the pathogenesis of AP-MODS. We created a mouse strain that is deficient for Kmo (encoding KMO) and that has a robust biochemical phenotype that protects against extrapancreatic tissue injury to the lung, kidney and liver in experimental AP-MODS. A medicinal chemistry strategy based on modifications of the kynurenine substrate led to the discovery of the oxazolidinone GSK180 as a potent and specific inhibitor of KMO. The binding mode of the inhibitor in the active site was confirmed by X-ray co-crystallography at 3.2 Å resolution. Treatment with GSK180 resulted in rapid changes in the levels of kynurenine pathway metabolites in vivo, and it afforded therapeutic protection against MODS in a rat model of AP. Our findings establish KMO inhibition as a novel therapeutic strategy in the treatment of AP-MODS, and they open up a new area for drug discovery in critical illness.

Status of the Suomi-NPP VIIRS Moisture Products

NASA Astrophysics Data System (ADS)

Borbas, E. E.; Li, Z.; Menzel, W. P.; Rada, M.

2017-12-01

The goal of the Soumi NPP VIIRS Moisture Project is to provide total column water vapor (TPW) properties from merged VIIRS infrared measurements and CrIS plus ATMS water vapor soundings to continue the depiction of global moisture at high spatial resolution started with MODIS. While MODIS has two water vapor channels within the 6.5 μm H2O absorption band and four channels within the 15 μm CO2 absorption band, VIIRS has no channels in either IR absorption band. The VIIRS/CrIS+ATMS TPW algorithm being developed at CIMSS is similar to the MOD07 synthetic regression algorithm. It uses the three VIIRS longwave IR window bands in a regression relation and adds the NUCAPS (CrIS+ATMS) water vapor product to compensate for the absence of VIIRS water vapor channels. This poster presents the methodology and evaluation of the S-NPP TPW Level 2 and 3 products with TPW data from ground-based and satellite-based measurements.

Triple point temperature of neon isotopes: Dependence on nitrogen impurity and sealed-cell model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pavese, F.; Steur, P. P. M.; Giraudi, D.

2013-09-11

This paper illustrates a study conducted at INRIM, to further check how some quantities influence the value of the triple point temperature of the neon high-purity isotopes {sup 20}Ne and {sup 22}Ne. The influence of nitrogen as a chemical impurity in neon is critical with regard to the present best total uncertainty achieved in the measurement of these triple points, but only one determination is available in the literature. Checks are reported, performed on two different samples of {sup 22}Ne known to contain a N{sub 2} amount of 157⋅10{sup −6}, using two different models of sealed cells. The model ofmore » the cell can, in principle, have some effects on the shape of the melting plateau or on the triple point temperature observed for the sample sealed in it. This can be due to cell thermal parameters, or because the INRIM cell element mod. c contains many copper wires closely packed, which can, in principle, constrain the interface and induce a premelting-like effect. The reported results on a cell mod. Bter show no evident effect from the cell model and provide a value for the effect of N{sub 2} in Ne liquidus point of 8.6(1.9) μK ppm N{sub 2}{sup −1}, only slightly different from the literature datum.« less

Increased levels of 3-hydroxykynurenine parallel disease severity in human acute pancreatitis.

PubMed

Skouras, Christos; Zheng, Xiaozhong; Binnie, Margaret; Homer, Natalie Z M; Murray, Toby B J; Robertson, Darren; Briody, Lesley; Paterson, Finny; Spence, Heather; Derr, Lisa; Hayes, Alastair J; Tsoumanis, Andreas; Lyster, Dawn; Parks, Rowan W; Garden, O James; Iredale, John P; Uings, Iain J; Liddle, John; Wright, Wayne L; Dukes, George; Webster, Scott P; Mole, Damian J

2016-09-27

Inhibition of kynurenine 3-monooxygenase (KMO) protects against multiple organ dysfunction (MODS) in experimental acute pancreatitis (AP). We aimed to precisely define the kynurenine pathway activation in relation to AP and AP-MODS in humans, by carrying out a prospective observational study of all persons presenting with a potential diagnosis of AP for 90 days. We sampled peripheral venous blood at 0, 3, 6, 12, 24, 48, 72 and 168 hours post-recruitment. We measured tryptophan metabolite concentrations and analysed these in the context of clinical data and disease severity indices, cytokine profiles and C-reactive protein (CRP) concentrations. 79 individuals were recruited (median age: 59.6 years; 47 males, 59.5%). 57 met the revised Atlanta definition of AP: 25 had mild, 23 moderate, and 9 severe AP. Plasma 3-hydroxykynurenine concentrations correlated with contemporaneous APACHE II scores (R 2  = 0.273; Spearman rho = 0.581; P < 0.001) and CRP (R 2  = 0.132; Spearman rho = 0.455, P < 0.001). Temporal profiling showed early tryptophan depletion and contemporaneous 3-hydroxykynurenine elevation. Furthermore, plasma concentrations of 3-hydroxykynurenine paralleled systemic inflammation and AP severity. These findings support the rationale for investigating early intervention with a KMO inhibitor, with the aim of reducing the incidence and severity of AP-associated organ dysfunction.

Increased levels of 3-hydroxykynurenine parallel disease severity in human acute pancreatitis

PubMed Central

Skouras, Christos; Zheng, Xiaozhong; Binnie, Margaret; Homer, Natalie Z. M.; Murray, Toby B. J.; Robertson, Darren; Briody, Lesley; Paterson, Finny; Spence, Heather; Derr, Lisa; Hayes, Alastair J.; Tsoumanis, Andreas; Lyster, Dawn; Parks, Rowan W.; Garden, O. James; Iredale, John P.; Uings, Iain J.; Liddle, John; Wright, Wayne L.; Dukes, George; Webster, Scott P.; Mole, Damian J.

2016-01-01

Inhibition of kynurenine 3-monooxygenase (KMO) protects against multiple organ dysfunction (MODS) in experimental acute pancreatitis (AP). We aimed to precisely define the kynurenine pathway activation in relation to AP and AP-MODS in humans, by carrying out a prospective observational study of all persons presenting with a potential diagnosis of AP for 90 days. We sampled peripheral venous blood at 0, 3, 6, 12, 24, 48, 72 and 168 hours post-recruitment. We measured tryptophan metabolite concentrations and analysed these in the context of clinical data and disease severity indices, cytokine profiles and C-reactive protein (CRP) concentrations. 79 individuals were recruited (median age: 59.6 years; 47 males, 59.5%). 57 met the revised Atlanta definition of AP: 25 had mild, 23 moderate, and 9 severe AP. Plasma 3-hydroxykynurenine concentrations correlated with contemporaneous APACHE II scores (R2 = 0.273; Spearman rho = 0.581; P < 0.001) and CRP (R2 = 0.132; Spearman rho = 0.455, P < 0.001). Temporal profiling showed early tryptophan depletion and contemporaneous 3-hydroxykynurenine elevation. Furthermore, plasma concentrations of 3-hydroxykynurenine paralleled systemic inflammation and AP severity. These findings support the rationale for investigating early intervention with a KMO inhibitor, with the aim of reducing the incidence and severity of AP-associated organ dysfunction. PMID:27669975

Myocardial motion estimation of tagged cardiac magnetic resonance images using tag motion constraints and multi-level b-splines interpolation.

PubMed

Liu, Hong; Yan, Meng; Song, Enmin; Wang, Jie; Wang, Qian; Jin, Renchao; Jin, Lianghai; Hung, Chih-Cheng

2016-05-01

Myocardial motion estimation of tagged cardiac magnetic resonance (TCMR) images is of great significance in clinical diagnosis and the treatment of heart disease. Currently, the harmonic phase analysis method (HARP) and the local sine-wave modeling method (SinMod) have been proven as two state-of-the-art motion estimation methods for TCMR images, since they can directly obtain the inter-frame motion displacement vector field (MDVF) with high accuracy and fast speed. By comparison, SinMod has better performance over HARP in terms of displacement detection, noise and artifacts reduction. However, the SinMod method has some drawbacks: 1) it is unable to estimate local displacements larger than half of the tag spacing; 2) it has observable errors in tracking of tag motion; and 3) the estimated MDVF usually has large local errors. To overcome these problems, we present a novel motion estimation method in this study. The proposed method tracks the motion of tags and then estimates the dense MDVF by using the interpolation. In this new method, a parameter estimation procedure for global motion is applied to match tag intersections between different frames, ensuring specific kinds of large displacements being correctly estimated. In addition, a strategy of tag motion constraints is applied to eliminate most of errors produced by inter-frame tracking of tags and the multi-level b-splines approximation algorithm is utilized, so as to enhance the local continuity and accuracy of the final MDVF. In the estimation of the motion displacement, our proposed method can obtain a more accurate MDVF compared with the SinMod method and our method can overcome the drawbacks of the SinMod method. However, the motion estimation accuracy of our method depends on the accuracy of tag lines detection and our method has a higher time complexity. Copyright © 2015 Elsevier Inc. All rights reserved.

Estimating Per-Pixel GPP of the Contiguous USA Directly from MODIS EVI Data

NASA Astrophysics Data System (ADS)

Rahman, A. F.; Sims, D. A.; El-Masri, B. Z.; Cordova, V. D.

2005-12-01

We estimated gross primary production (GPP) of the contiguous USA using enhanced vegetation index (EVI) data from NASA's moderate resolution imaging spectroradiometer (MODIS). Based on recently published values of correlation coefficients between EVI and GPP of North American vegetations, we derived GPP maps of the contiguous USA for 2001-2004, which included one La Nina year and three moderately El Nino years. The product was a truly per-pixel GPP estimate (named E-GPP), in contrast to the pseudo-continuous MOD17, the standard MODIS GPP product. We compared E-GPP with fine-scale experimental GPP data and MOD17 estimates from three Bigfoot experimental sites, and also with MOD17 estimates from the whole contiguous USA for the above-mentioned four years. For each of the '7 by 7' km Bigfoot experimental sites, E-GPP was able to track the primary production activity during the green-up period while MOD17 failed to do so. The E-GPP estimates during peak production season were similar to those from Bigfoot and MOD17 for most vegetation types except for the deciduous types, where it was lower. Annual E-GPP of the Bigfoot sites compared well with Bigfoot experimental GPP (r = 0.71) and MOD17 (r = 0.78). But for the contiguous USA for 2001-2004, annual E-GPP showed disagreement with MOD17 in both magnitude and seasonal trends for deciduous forests and grass lands. In this study we explored the reasons for this mismatch between E-GPP and MOD17 and also analyzed the uncertainties in E-GPP across multiple spatial scales. Our results show that the E-GPP, based on a simple regression model, can work as a robust alternative to MOD17 for large-area annual GPP estimation. The relative advantages of E-GPP are that it is truly per-pixel, solely dependent on remotely sensed data that is routinely available from NASA, easy to compute and has the potential of being used as an operational product.

One-loop light-cone QCD, effective action for reggeized gluons and QCD RFT calculus

NASA Astrophysics Data System (ADS)

Bondarenko, S.; Lipatov, L.; Pozdnyakov, S.; Prygarin, A.

2017-09-01

The effective action for reggeized gluons is based on the gluodynamic Yang-Mills Lagrangian with external current for longitudinal gluons added, see Lipatov (Nucl Phys B 452:369, 1995; Phys Rep 286:131, 1997; Subnucl Ser 49:131, 2013; Int J Mod Phys Conf Ser 39:1560082, 2015; Int J Mod Phys A 31(28/29):1645011, 2016; EPJ Web Conf 125:01010, 2016). On the base of classical solutions, obtained in Bondarenko et al. (Eur Phys J C 77(8):527, 2017), the one-loop corrections to this effective action in light-cone gauge are calculated. The RFT calculus for reggeized gluons similarly to the RFT introduced in Gribov (Sov Phys JETP 26:414, 1968) is proposed and discussed. The correctness of the results is verified by calculation of the propagators of A+ and A- reggeized gluons fields and application of the obtained results is discussed as well.

Pretest analysis document for Test S-NH-1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owca, W.A.

This report documents the pretest analysis calculation completed with the RELAP5/MOD2/CY3601 code for Semiscale MOD-2C Test S-NH-1. The test will simulate the shear of a small diameter penetration of a cold leg, equivalent to 0.5% of the cold leg flow area. The high pressure injection system is assumed to be inoperative throughout the transient. The recovery procedure consists of latching open both steam generator ADV's while feeding with auxiliary feedwater, and accumulator operation. Recovery will be initiated upon a peak cladding temperature of 811 K (1000/sup 0/F). The test will be terminated when primary pressure has been reduced to themore » low pressure injection system setpoint of 1.38 MPa (200 psia). The calculated results indicate that the test objectives can be achieved and the proposed test scenario poses no threat to personnel or to plant integrity. 12 figs.« less

Local gas injection as a scrape-off layer diagnostic on the Alcator C-Mod tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jablonski, David F.

1996-05-01

A capillary puffing array has been installed on Alcator C-Mod which allows localized introduction of gaseous species in the scrape-off layer. This system has been utilized in experiments to elucidate both global and local properties of edge transport. Deuterium fueling and recycling impurity screening are observed to be characterized by non-dimensional screening efficiencies which are independent of the location of introduction. In contrast, the behavior of non-recycling impurities is seen to be characterized by a screening time which is dependent on puff location. The work of this thesis has focused on the use of the capillary array with a cameramore » system which can view impurity line emission plumes formed in the region of an injection location. The ionic plumes observed extend along the magnetic field line with a comet-like asymmetry, indicative of background plasma ion flow. The flow is observed to be towards the nearest strike-point, independent of x-point location, magnetic field direction, and other plasma parameters. While the axes of the plumes are generally along the field line, deviations are seen which indicate cross-field ion drifts. A quasi-two dimensional fluid model has been constructed to use the plume shapes of the first charge state impurity ions to extract information about the local background plasma, specifically the temperature, parallel flow velocity, and radial electric field. Through comparisons of model results with those of a three dimensional Monte Carlo code, and comparisons of plume extracted parameters with scanning probe measurements, the efficacy of the model is demonstrated. Plume analysis not only leads to understandings of local edge impurity transport, but also presents a novel diagnostic technique.« less

NMR crystallography of oxybuprocaine hydrochloride, Modification II degrees.

PubMed

Harris, Robin K; Cadars, Sylvian; Emsley, Lyndon; Yates, Jonathan R; Pickard, Chris J; Jetti, Ram K R; Griesser, Ulrich J

2007-01-21

The (13)C CPMAS spectrum is presented for the polymorph of oxybuprocaine hydrochloride which is stable at room temperature, i.e. Mod. II degrees . It shows crystallographic splittings arising from the fact that there are two molecules, with substantially different conformations, in the asymmetric unit. An INADEQUATE two-dimensional experiment was used to link signals for the same independent molecule. The chemical shifts are discussed in relation to the crystal structure. Of the four ethyl groups attached to NH(+) nitrogens, one gives rise to unusually low chemical shifts, very different from those of the other three ethyl groups. This is attributed empirically to gamma-gauche conformational effects, as is confirmed by shielding computations. These considerations allow (13)C signals to be assigned to specific carbons in the two crystallographically inequivalent molecules in the crystal structure. Indeed, information about the conformations is inherent in the NMR spectrum, which thus provides data of crystallographic significance. A (13)C/(1)H HETCOR experiment enabled resolution to be obtained in the (1)H dimension and allowed (1)H and (13)C signals for the same independent molecule to be linked.

Blood fatty acid changes in healthy young Americans in response to a 10-week diet that increased n-3 and reduced n-6 fatty acid consumption: a randomised controlled trial.

PubMed

Young, Andrew J; Marriott, Bernadette P; Champagne, Catherine M; Hawes, Michael R; Montain, Scott J; Johannsen, Neil M; Berry, Kevin; Hibbeln, Joseph R

2017-05-01

Military personnel generally under-consume n-3 fatty acids and overconsume n-6 fatty acids. In a placebo-controlled, double-blinded study, we investigated whether a diet suitable for implementation in military dining facilities and civilian cafeterias could benefit n-3/n-6 fatty acid status of consumers. Three volunteer groups were provided different diets for 10 weeks. Control (CON) participants consumed meals from the US Military's Standard Garrison Dining Facility Menu. Experimental, moderate (EXP-Mod) and experimental-high (EXP-High) participants consumed the same meals, but high n-6 fatty acid and low n-3 fatty acid containing chicken, egg, oils and food ingredients were replaced with products having less n-6 fatty acids and more n-3 fatty acids. The EXP-High participants also consumed smoothies containing 1000 mg n-3 fatty acids per serving, whereas other participants received placebo smoothies. Plasma and erythrocyte EPA and DHA in CON group remained unchanged throughout, whereas EPA, DHA and Omega-3 Index increased in EXP-Mod and EXP-High groups, and were higher than in CON group after 5 weeks. After 10 weeks, Omega-3 Index in EXP-High group had increased further. No participants exhibited changes in fasting plasma TAG, total cholesterol, LDL, HDL, mood or emotional reactivity. Replacing high linoleic acid (LA) containing foods in dining facility menus with similar high oleic acid/low LA and high n-3 fatty acid foods can improve n-6/n-3 blood fatty acid status after 5 weeks. The diets were well accepted and suitable for implementation in group feeding settings like military dining facilities and civilian cafeterias.

Executable Architecture of Net Enabled Operations: State Machine of Federated Nodes

DTIC Science & Technology

2009-11-01

verbal descriptions from operators) of the current Command and Control (C2) practices into model form. In theory these should be Standard Operating...faudra une grande quantité de données pour faire en sorte que le modèle reflète les processus véritables, les auteurs recommandent que la machine à...descriptions from operators) of the current C2 practices into model form. In theory these should be SOPs that execute as a thread from start to finish. The

Development and Evaluation of an Airplane Fuel Tank Ullage Composition Model. Volume 2. Experimental Determination of Airplane Fuel Tank Ullage Compositions

DTIC Science & Technology

1987-10-01

Airplane Fuel Tank Ullage Compositions ~C A. J. Roth BOEING MILITARY AIRPLANE COMPANY P. 0. Box 3707 Seattle, Washington 98124-2207 October 1987 FINAL...controlled mission simulations were made using the ModComp computer to control the Simulated Aircraft Fuel Tank Environment ( SAFTEI facility at Wright...of this report. iii PREFACE This is a final report of work conducted under F33615-84-C-2431 and submitted by the Boeing Military Airplane Company

Time-domain simulation of nonlinear radiofrequency phenomena

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jenkins, Thomas G.; Austin, Travis M.; Smithe, David N.

Nonlinear effects associated with the physics of radiofrequency wave propagation through a plasma are investigated numerically in the time domain, using both fluid and particle-in-cell (PIC) methods. We find favorable comparisons between parametric decay instability scenarios observed on the Alcator C-MOD experiment [J. C. Rost, M. Porkolab, and R. L. Boivin, Phys. Plasmas 9, 1262 (2002)] and PIC models. The capability of fluid models to capture important nonlinear effects characteristic of wave-plasma interaction (frequency doubling, cyclotron resonant absorption) is also demonstrated.

Time-domain simulation of nonlinear radiofrequency phenomena

NASA Astrophysics Data System (ADS)

Jenkins, Thomas G.; Austin, Travis M.; Smithe, David N.; Loverich, John; Hakim, Ammar H.

2013-01-01

Nonlinear effects associated with the physics of radiofrequency wave propagation through a plasma are investigated numerically in the time domain, using both fluid and particle-in-cell (PIC) methods. We find favorable comparisons between parametric decay instability scenarios observed on the Alcator C-MOD experiment [J. C. Rost, M. Porkolab, and R. L. Boivin, Phys. Plasmas 9, 1262 (2002)] and PIC models. The capability of fluid models to capture important nonlinear effects characteristic of wave-plasma interaction (frequency doubling, cyclotron resonant absorption) is also demonstrated.

Automotive Stirling engine systems development

NASA Technical Reports Server (NTRS)

Richey, A. E.

1984-01-01

The objective of the Automotive Stirling Engine (ASE) program is to develop a Stirling engine for automotive use that provides a 30 percent improvement in fuel economy relative to a comparable internal-combustion engine while meeting emissions goals. This paper traces the engine systems' development efforts focusing on: (1) a summary of engine system performance for all Mod I engines; (2) the development, program conducted for the upgraded Mod I; and (3) vehicle systems work conducted to enhance vehicle fuel economy. Problems encountered during the upgraded Mod I test program are discussed. The importance of the EPA driving cycle cold-start penalty and the measures taken to minimize that penalty with the Mod II are also addressed.

Pretest mediction of Semiscale Test S-07-10 B. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dobbe, C A

A best estimate prediction of Semiscale Test S-07-10B was performed at INEL by EG and G Idaho as part of the RELAP4/MOD6 code assessment effort and as the Nuclear Regulatory Commission pretest calculation for the Small Break Experiment. The RELAP4/MOD6 Update 4 and the RELAP4/MOD7 computer codes were used to analyze Semiscale Test S-07-10B, a 10% communicative cold leg break experiment. The Semiscale Mod-3 system utilized an electrially heated simulated core operating at a power level of 1.94 MW. The initial system pressure and temperature in the upper plenum was 2276 psia and 604/sup 0/F, respectively.

Health status of illicit stimulant drug users in rural Ohio.

PubMed

Falck, Russel S; Wang, Jichuan; Carlson, Robert G

2007-11-01

The SF-8 health survey was used to assess the physical and mental health status of a community sample of not-in-treatment, illicit stimulant drug-using adults (n = 249) living in rural Ohio. Physical health status scores indicative of poor health were present in 30.5% of the sample. Poor physical health was associated with older age (OR = 1.06; 95% C.I. = 1.02-1.11), chronic disease (OR = 2.24, 95% C.I. = 1.14-4.40), and frequent opioid use (OR = 3.14, 95% C.I. = 1.16-8.50). Poor mental health status scores were present in 63.9% of the sample. Men were less likely (OR = 0.25, 95% C.I. = 0.11-0.53), and Whites more likely (OR = 3.97, 95% C.I. = 1.56-10.13), to have poor mental health scores. Frequency and type of drug use had no measurable effect on mental health status. Physical and mental health problems are likely to be pervasive among nonmedical drug users in rural areas.

Characterization of the Hamamatsu 8" R5912-MOD Photomultiplier tube

NASA Astrophysics Data System (ADS)

Kaptanoglu, Tanner

2018-05-01

Current and future neutrino and direct detection dark matter experiments hope to take advantage of improving technologies in photon detection. Many of these detectors are large, monolithic optical detectors that use relatively low-cost, large-area, and efficient photomultiplier tubes (PMTs). A candidate PMT for future experiments is a newly developed prototype Hamamatsu PMT, the R5912-MOD. In this paper we describe measurements made of the single photoelectron time and charge response of the R5912-MOD, as well as detail some direct comparisons to similar PMTs. Most of these measurements were performed on three R5912-MOD PMTs operating at gains close to 1 × 107. The transit time spread (σ) and the charge peak-to-valley were measured to be on average 680ps and 4.2 respectively. The results of this paper show the R5912-MOD is an excellent candidate for future experiments in several regards, particularly due to its narrow spread in timing.

Comparison of three methods for determination of N-nitrosopyrrolidine in fried dry-cured bacon.

PubMed

Gates, R A; Pensabene, J W; Fiddler, W

1984-01-01

The recently developed Eastern Regional Research Center ( ERRC ) dry column chromatographic procedure for determining N-nitrosopyrrolidine (NPYR) in fried cure-pumped bacon was evaluated for its applicability to fried dry-cured bacon. The method was then compared with 2 established procedures for volatile nitrosamine analysis in cured meat products: the multidetection thermal energy analyzer (MD) method and the mineral oil distillation (MOD) screening procedure. No significant difference (P less than 0.05) in NPYR values was found between the ERRC and MD procedures, but significant differences were found between the ERRC and MOD procedures and between the MOD and MD procedures. No artifactual nitrosamine formation was found in the ERRC procedure, but significant amounts were found in samples analyzed by the MOD procedure. The ERRC method was demonstrated to be rugged and very rapid. It is proposed that the ERRC method replace the MOD method as the official screening procedure for NPYR in fried bacon.

Mod-2 wind turbine system cluster research test program. Volume 1: Initial plan E-1290

NASA Technical Reports Server (NTRS)

Gordon, L. H.

1982-01-01

Upon completion of the design and development of three Mod-2 wind turbines, a series of research experiments are planned to gather data on and evaluate the performance, environmental effects, and operation of a cluster as well as a single, large multimegawatt wind turbine. Information on the program objectives, a Mod-2 system description, a planned schedule, organizational roles, and responsibilities, is included.

Mod-5A wind turbine generator program design report. Volume 4: Drawings and specifications, book 5

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. There are four volumes. This volume contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. Detail drawings of several assemblies and subassemblies are given. This is the fifth book of volume 4.

Culture and Creativity: World of Warcraft Modding in China and the US

NASA Astrophysics Data System (ADS)

Kow, Yong Ming; Nardi, Bonnie

Modding - end-user modification of commercial hardware and software - can be traced back at least to 1961 when Spacewar! was developed by a group of MIT students on a DEC PDP-1. Spacewar! evolved into arcade games including Space Wars produced in 1977 by Cinematronics (Sotamaa 2003). In 1992, players altering Wolfenstein 3-D (1992), a first person shooter game made by id Software, overwrote the graphics and sounds by editing the game files. Learning from this experience, id Software released Doom in 1993 with isolated media files and open source code for players to develop custom maps, images, sounds, and other utilities. Players were able to pass on their modifications to others. By 1996, with the release of Quake, end-user modifications had come to be known as "mods," and modding was an accepted part of the gaming community (Kucklich 2005; Postigo 2008a, b). Since late-2005, we have been studying World of Warcraft (WoW) in which the use of mods is an important aspect of player practice (Nardi and Harris 2006; Nardi et al. 2007). Technically minded players with an interest in extending the game write mods and make them available to players for free download on distribution sites. Most modders work for free, but the distribution sites are commercial enterprises with advertising.

2013 Nuclear Fusion Prize Acceptance Speech 2013 Nuclear Fusion Prize Acceptance Speech

NASA Astrophysics Data System (ADS)

Whyte, D.

2015-01-01

I would like to express gratitude to the IAEA, the journal Nuclear Fusion and its board for this acknowledgement of work carried out at the MIT Alcator C-Mod tokamak. I must begin by making it clear that this is in no way an award to an individual. The experiments, data analysis and paper were a true collaborative effort from the C-Mod team. It is a honor to work with them and to accept the award on their behalf. I would also like to thank the US Department of Energy for their support in funding this research. The paper describes the exploration of the 'improved' confinement regime dubbed 'I-mode'. The distinguishing feature of this operational mode is a robust boundary pedestal in temperature with the somewhat surprising lack of any form of density pedestal. Thus the regime exhibits an enhanced energy confinement similar to H-mode, roughly double of L-mode at fixed input power, yet has global fuel and impurity particle transport of L-mode. These features are intriguing from a scientific and practical point of view. On the science side it is extremely useful to obtain such a clear demarcation between the energy and particle transport. For example, soon after its discovery, the I-mode was used to extract the observation that the edge T pedestal is the strongest determinant for intrinsic rotation in work by John Rice, Pat Diamond and colleagues. Recent results regarding core transport by Anne White, Nate Howard and colleagues show that I-mode has intriguing properties with respect to core response of fluctuations and profile stiffness. Mike Churchill's recent Ph. D study on C-Mod shows that I-mode exhibits no strong poloidal impurity asymmetry, unlike H-mode. The I-mode posed an interesting test for the peeling-ballooning-KBM model of the pedestal, the subject of the 2014 Nuclear Fusion award of Phil Snyder, and was examined by John Walk and Jerry Hughes showing that in fact the lack of the density pedestal pushed the I-mode far away from the P-B limit, and thus the limiting transport/stability feature of the I-mode was in a sense self-enforcing for keeping the regime free of ELMs. Also intriguing is that the I-mode exhibits global energy confinement scaling with a very weak power degradation, presumably this arises from a temperature pedestal which is not regulated by stability, it seems I-mode provides fertile ground for studying basic plasma phenomena. From a pragmatic point of view I-mode has now been obtained and studied in ASDEX-Upgrade and DIII-0D, as reported by Amanda Hubbard at this conference. There are interesting similarities to the C-Mod observations, such as a Te pedestal without a density pedestal, but also differences which are being sorted through in details of the edge fluctuations and the operational window to access I-mode. The I-mode is 'found' at power levels between L- and H, and thus suppressing the H-mode transition is a key aspect to maintaining I-mode. This is done basically by operating with the ion grad-B drift pointed away from the primary X-point. This is one of the reasons why intrinsically stationary regimes like I-mode, and others like QH-mode, are an attractive option for burning plasma scenarios without the need for ELM, if accessible and maintainable this requires no additional hardware since the pedestal self-regulates. In addition I-mode is highly attractive because of the L-mode particle confinement: the turbulence-dominated particle transport greatly eases both fuelling requirements and impurity control. Indeed I-mode is highly successful on the all high-Z wall of C-Mod. And in a burning plasma the control of the operating point is primarily through density control, thus one foresees that burn control through densification is very powerful and promising. Recent work has suggested that the power requirement to access I-mode has rather weak B dependence. This may explain why the regime has a relatively wide operating window in the high-field C-Mod and I-mode may be highly applicable to high B ITER and reactors. So while it is relatively early after this paper and the I-mode discovery, we expect continued interesting work in this area. I would also like to point out another feature of the Nuclear Fusion paper from 2010. Approximately one third of the co-authors were students at the time when the paper was written. Indeed, it is unlikely that I-mode would have been discovered without students. A student, Rachael McDermott, was seeking to slow down the confinement transition time in order to capture it with her new charge-exchange spectroscopy diagnostic. The attempt was a 'crazy idea' to use the 'unfavorable' grad-B drift with a very careful set of small power steps just below the H-mode transition. It was in such steps that the I-mode was found and then later expanded to a much wider operating window once it was realized how attractive the I-mode appeared. I believe the fusion community can take two lessons from this. First, it is vital that we continue to support the education of young scientists. Our investments in new devices are for naught if we do not have an extremely talented and trained new generation coming behind us. And to do that means we need to assure student are integrated with access to leading facilities like C-Mod where one third of the session leaders are students. Secondly, and related, small, capable and versatile fusion experiments are both highly appropriate to meet the education mission and to push forward the fusion science because of their ability to take on risk and try new ideas, and to explore unique, but relevant, parts of parameter space such as high magnet field fusion. I urge that we continue to support such facilities in the international fusion portfolio. Thank you again on behalf of the co-authors and the C-Mod team.

Metabolic and hormonal responses to isoenergetic high-intensity interval exercise and continuous moderate-intensity exercise.

PubMed

Peake, Jonathan M; Tan, Sok Joo; Markworth, James F; Broadbent, James A; Skinner, Tina L; Cameron-Smith, David

2014-10-01

This study investigated the effects of high-intensity interval training (HIIT) vs. work-matched moderate-intensity continuous exercise (MOD) on metabolism and counterregulatory stress hormones. In a randomized and counterbalanced order, 10 well-trained male cyclists and triathletes completed a HIIT session [81.6 ± 3.7% maximum oxygen consumption (V̇o2 max); 72.0 ± 3.2% peak power output; 792 ± 95 kJ] and a MOD session (66.7 ± 3.5% V̇o2 max; 48.5 ± 3.1% peak power output; 797 ± 95 kJ). Blood samples were collected before, immediately after, and 1 and 2 h postexercise. Carbohydrate oxidation was higher (P = 0.037; 20%), whereas fat oxidation was lower (P = 0.037; -47%) during HIIT vs. MOD. Immediately after exercise, plasma glucose (P = 0.024; 20%) and lactate (P < 0.01; 5.4×) were higher in HIIT vs. MOD, whereas total serum free fatty acid concentration was not significantly different (P = 0.33). Targeted gas chromatography-mass spectromtery metabolomics analysis identified and quantified 49 metabolites in plasma, among which 11 changed after both HIIT and MOD, 13 changed only after HIIT, and 5 changed only after MOD. Notable changes included substantial increases in tricarboxylic acid intermediates and monounsaturated fatty acids after HIIT and marked decreases in amino acids during recovery from both trials. Plasma adrenocorticotrophic hormone (P = 0.019), cortisol (P < 0.01), and growth hormone (P < 0.01) were all higher immediately after HIIT. Plasma norepinephrine (P = 0.11) and interleukin-6 (P = 0.20) immediately after exercise were not significantly different between trials. Plasma insulin decreased during recovery from both HIIT and MOD (P < 0.01). These data indicate distinct differences in specific metabolites and counterregulatory hormones following HIIT vs. MOD and highlight the value of targeted metabolomic analysis to provide more detailed insights into the metabolic demands of exercise. Copyright © 2014 the American Physiological Society.

Streptococcal Toxic Shock syndrome.

PubMed

Krishna, Vidya; Sankaranarayan, Shuba; Sivaraman, Rajakumar Padur; Prabaharan, Krithika

2014-09-01

Streptococcal Toxic Shock syndrome (STSS) is a serious complication caused by exotoxins of Group A Streptococcus (GAS). It presents with fulminant shock and rash, is rapidly progressive with Multi-Organ Dysfunction Syndrome (MODS) and requires aggressive therapy with fluids, antibiotics and source control.

Assessing Weapon System Acquisition Cycle Times: Setting Program Schedules

DTIC Science & Technology

2015-06-01

kits begins in FY16 – “Required Assets Available ( RAA )” Sepember 2019 (means first unit equipped) *RDT&E exceeds threshold 22 C. Summary and...July 2013 CPD 2006 CDD by USMC Apr. 2014a F-22 3.2B Mod RAA : 4QFY19 None identified None identified Enhanced Global Strike 2007a Incr. 3.2B KSAs

High-resolution disruption halo current measurements using Langmuir probes in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Tinguely, R. A.; Granetz, R. S.; Berg, A.; Kuang, A. Q.; Brunner, D.; LaBombard, B.

2018-01-01

Halo currents generated during disruptions on Alcator C-Mod have been measured with Langmuir ‘rail’ probes. These rail probes are embedded in a lower outboard divertor module in a closely-spaced vertical (poloidal) array. The dense array provides detailed resolution of the spatial dependence (~1 cm spacing) of the halo current distribution in the plasma scrape-off region with high time resolution (400 kHz digitization rate). As the plasma limits on the outboard divertor plate, the contact point is clearly discernible in the halo current data (as an inversion of current) and moves vertically down the divertor plate on many disruptions. These data are consistent with filament reconstructions of the plasma boundary, from which the edge safety factor of the disrupting plasma can be calculated. Additionally, the halo current ‘footprint’ on the divertor plate is obtained and related to the halo flux width. The voltage driving halo current and the effective resistance of the plasma region through which the halo current flows to reach the probes are also investigated. Estimations of the sheath resistance and halo region resistivity and temperature are given. This information could prove useful for modeling halo current dynamics.

Upgraded PMI diagnostic capabilities using Accelerator-based In-situ Materials Surveillance (AIMS) on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Kesler, Leigh; Barnard, Harold; Hartwig, Zachary; Sorbom, Brandon; Lanza, Richard; Terry, David; Vieira, Rui; Whyte, Dennis

2014-10-01

The AIMS diagnostic was developed to rapidly and non-invasively characterize in-situ plasma material interactions (PMI) in a tokamak. Recent improvements are described which significantly expand this measurement capability on Alcator C-Mod. The detection time at each wall location is reduced from about 10 min to 30 s, via improved hardware and detection geometry. Detectors are in an augmented re-entrant tube to maximize the solid angle between detectors and diagnostic locations. Spatial range is expanded by using beam dynamics simulation to design upgraded B-field power supplies to provide maximal poloidal access, including a ~20° toroidal range in the divertor. Measurement accuracy is improved with angular and energy resolved cross section measurements obtained using a separate 0.9 MeV deuteron ion accelerator. Future improvements include the installation of recessed scintillator tiles as beam targets for calibration of the diagnostic. Additionally, implanted depth marker tiles will enable AIMS to observe the in-situ erosion and deposition of high-Z plasma-facing materials. This work is supported by U.S. DOE Grant No. DE-FG02-94ER54235 and Cooperative Agreement No. DE-FC02-99ER54512.

Tungsten migration in Alcator C-Mod: sputtering and melting

NASA Astrophysics Data System (ADS)

Wright, G. M.; Barnard, H.; Lipschultz, B.; Whyte, D. G.

2010-11-01

A row of bulk tungsten (W) tiles were installed near the typical outer strike-point location in the Alcator C-Mod divertor in 2007. In the 2009/2010 campaign, one of the W tiles mechanically failed resulting in significant W melting at that location. Post-campaign PIXE surface analysis has been used to observe tungsten (W) deposition and migration patterns in the divertor for the typical operations (sputtering only) and operation with melted components. For sputtering conditions, W deposition of up to 20 nm equivalent thickness is observed at various divertor surfaces indicating prompt re-deposition at the outer divertor, neutral and ion transport through the private-flux region and ion transport in the scrape off layer. For melting conditions, W deposition of up to 400 nm equivalent thickness is observed at some locations at the outer divertor. However, the toroidal distribution of W on the outer divertor is strongly non-uniform. There is no W deposition measured on the inner wall limiter. These results indicate that impurity migration is affected by the erosion mechanism and source, with the migration from melting being less predictable and uniform than from the sputtering case. Supported by USDoE award DE-SC00-02060.

Lower Hybrid Wave Induced Rotation on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Parker, Ron; Podpaly, Yuri; Rice, John; Schmidt, Andrea

2009-11-01

Injection of RF power in the vicinity of the lower hybrid frequency has been observed to cause strong counter current rotation in Alcator C-Mod plasmas [1,2]. The spin-up rate is consistent with the rate at which momentum is injected by the LH waves, and also the rate at which fast electron momentum is transferred to the ions. A momentum diffusivity of ˜ 0.1 m^2/s is sufficient to account for the observed steady-state rotation. This value is also comparable with that derived from an analysis of rotation induced by RF mode conversion [3]. Radial force balance requires a radial electric field, suggesting a buildup of negative charge in the plasma core. This may be the result of an inward pinch of the LH produced fast electrons, as would be expected for resonant trapped particles. Analysis of the fast-electron-produced bremsstrahlung during LH power modulation experiments yields an inward pinch velocity of ˜ 1 m/s, consistent with the estimated trapped particle pinch velocity. [4pt] [1] A. Ince-Cushman, et.al., Phys. Rev. Lett., 102, 035002 (2009)[0pt] [2] J. E. Rice, et. al., Nucl. Fusion 49, 025004 (2009)[0pt] [3] Y. Lin, et.al., this meeting

Electron Profile Stiffness and Critical Gradient Length Studies in the Alcator C-Mod Tokamak

NASA Astrophysics Data System (ADS)

Houshmandyar, Saeid; Hatch, David R.; Liao, Kenneth T.; Zhao, Bingzhe; Phillips, Perry E.; Rowan, William L.; Cao, Norman; Ernst, Darin R.; Rice, John E.

2017-10-01

Electron temperature profile stiffness was investigated at Alcator C-Mod L-mode discharges. Electrons were heated by ion cyclotron range of frequencies (ICRF) through minority heating. The intent of the heating mechanism was to vary the heat flux and simultaneously, gradually change the local gradient. The electron temperature gradient scale length (LTe- 1 = | ∇Te |/Te) was accurately measured through a novel technique, using the high-resolution radiometer ECE diagnostic. The TRANSP power balance analysis (Q/QGB) and the measured scale length (a/LTe) result in critical scale length measurements at all major radius locations. These measurements suggest that the profiles are already at the critical values. Furthermore, the dependence of the stiffness on plasma rotation and magnetic shear will be discussed. In order to understand the underlying mechanism of turbulence for these discharges, simulations using the gyrokinetic code, GENE, were carried out. For linear runs at electron scales, it was found that the largest growth rates are very sensitive to a/LTe variation, which suggests the presence of ETG modes, while the sensitivity studies in the ion scales indicate ITG/TEM modes. Supported by USDoE awards DE-FG03-96ER54373 and DE-FC02-99ER54512.

Additive Manufacture (3D Printing) of Plasma Diagnostic Components and Assemblies for Fusion Experiments

NASA Astrophysics Data System (ADS)

Quinley, Morgan; Chun, Katherine; Melnik, Paul; Sieck, Paul; Smith, Trevor; Stuber, James; Woodruff, Simon; Romero-Talamas, Carlos; Rivera, William; Card, Alexander

2016-10-01

We are investigating the potential impact of additive manufacturing (3D printing) on the cost and complexity of plasma diagnostics. We present a survey of the current state-of-the-art in additive manufacture of metals, as well as the design of diagnostic components that have been optimized for and take advantage of these processes. Included among these is a set of retarding field analyzer probe heads that have been printed in tungsten with internal heat sinks and cooling channels. Finite element analysis of these probe heads shows the potential for a 750K reduction in peak temperature, allowing the probe to take data twice as often without melting. Results of the evaluation of these probe heads for mechanical strength and outgassing, as well as their use on Alcator C-Mod will be presented. Supported by DOE SBIR Grant DE-SC0011858.

Interaction between light and superconductors

NASA Astrophysics Data System (ADS)

Gilabert, Alain

In the first part of this review article we resume briefly the fundamental aspect of the photon-superconductor interaction. The emphase is focused on the characteristic times and on the phenomenological models (the T*, the μ* models and the model of the kinetics equations) describing the out of equilibrium superconductivity. The experiments made on classical illuminated superconductors especially on tunnel junctions are then reported. In the second part we present the applied aspect of the photon-superconductor interaction. The interaction of the light with the high Tc superconductors is reviewed in the last part. Dans la première partie de cet article de revue, on résume brièvement 1'aspect fondamental de l'action des photons sur les supraconducteurs en s'attachant surtout à rappeler les différents temps caractéristiques de cette interaction et les modèles phénoménologiques (le modèle T*, le modèle μ*, le modèle des équations cinétiques) décrivant la supraconductivité hors équilibre. La seconde partie rappelle les expériences réalisées sur les supraconducteurs classiques illuminés et spécialement les jonctions tunnel ainsi que certaines applications de la supraconductivité hors équilibre comme les liens faibles controllables par des moyens optiques. La dernière partie est consacrée aux nouvelles expériences qui démarrent concernant l'action de la lumière sur les supraconducteurs à hautes températures critiques.

H-mode achievement and edge features in RFX-mod tokamak operation

NASA Astrophysics Data System (ADS)

Spolaore, M.; Cavazzana, R.; Marrelli, L.; Carraro, L.; Franz, P.; Spagnolo, S.; Zaniol, B.; Zuin, M.; Cordaro, L.; Dal Bello, S.; De Masi, G.; Ferro, A.; Finotti, C.; Grando, L.; Grenfell, G.; Innocente, P.; Kudlacek, O.; Marchiori, G.; Martines, E.; Momo, B.; Paccagnella, R.; Piovesan, P.; Piron, C.; Puiatti, M. E.; Recchia, M.; Scarin, P.; Taliercio, C.; Vianello, N.; Zanotto, L.

2017-11-01

The RFX-mod experiment is a fusion device designed to operate as a reversed field pinch (RFP), with a major radius R = 2 m and a minor radius a = 0.459 m. Its high versatility recently allowed operating it also as an ohmic tokamak, allowing comparative studies between the two configurations in the same device. The device is equipped with a state of the art MHD mode feedback control system providing a magnetic boundary effective control, by applying resonant or non-resonant magnetic perturbations (MP), both in RFP and in tokamak configurations. In the fusion community the application of MPs is widely studied as a promising tool to limit the impact of plasma filaments and ELMs (edge localized modes) on plasma facing components. An important new research line is the exploitation of the RFX-mod active control system for ELM mitigation studies. As a first step in this direction, this paper presents the most recent achievements in term of RFX-mod tokamak explored scenarios, which allowed the first investigation of the ohmic and edge biasing induced H-mode. The production of D-shaped tokamak discharges and the design and deployment of an insertable polarized electrode were accomplished. Reproducible H-mode phases were obtained with insertable electrode negative biasing in single null discharges, representing an unexplored scenario with this technique. Important modifications of the edge plasma density and flow properties are observed. During the achieved H-mode ELM-like electromagnetic composite filamentary structures are observed. They are characterized by clear vorticity and parallel current density patterns.

Optimization of the Ussing chamber setup with excised rat intestinal segments for dissolution/permeation experiments of poorly soluble drugs.

PubMed

Forner, Kristin; Roos, Carl; Dahlgren, David; Kesisoglou, Filippos; Konerding, Moritz A; Mazur, Johanna; Lennernäs, Hans; Langguth, Peter

2017-02-01

Prediction of the in vivo absorption of poorly soluble drugs may require simultaneous dissolution/permeation experiments. In vivo predictive media have been modified for permeation experiments with Caco-2 cells, but not for excised rat intestinal segments. The present study aimed at improving the setup of dissolution/permeation experiments with excised rat intestinal segments by assessing suitable donor and receiver media. The regional compatibility of rat intestine in Ussing chambers with modified Fasted and Fed State Simulated Intestinal Fluids (Fa/FeSSIF mod ) as donor media was evaluated via several parameters that reflect the viability of the excised intestinal segments. Receiver media that establish sink conditions were investigated for their foaming potential and toxicity. Dissolution/permeation experiments with the optimized conditions were then tested for two particle sizes of the BCS class II drug aprepitant. Fa/FeSSIF mod were toxic for excised rat ileal sheets but not duodenal sheets, the compatibility with jejunal segments depended on the bile salt concentration. A non-foaming receiver medium containing bovine serum albumin (BSA) and Antifoam B was nontoxic. With these conditions, the permeation of nanosized aprepitant was higher than of the unmilled drug formulations. The compatibility of Fa/FeSSIF mod depends on the excised intestinal region. The chosen conditions enable dissolution/permeation experiments with excised rat duodenal segments. The experiments correctly predicted the superior permeation of nanosized over unmilled aprepitant that is observed in vivo. The optimized setup uses FaSSIF mod as donor medium, excised rat duodenal sheets as permeation membrane and a receiver medium containing BSA and Antifoam B.

Progress Report, Grant AFOSR-79-0134, September 1, 1982 - April 30, 1983,

DTIC Science & Technology

1983-04-30

Lippmann, Professor of Physics, Emeritus, New York University; Kevin C. Nunan, Graduate Student; Michael I. Weinstein, Postdoctoral --J Fellow...iLipIIiani, Pro lessor of hscEirt:,NwYr University; R. Kevin C. Nunan, G1,aduaIZte Student; 9. Michacl1 1. Weinsteini, Postdoctoral Fellow, Stanf’ord Un...khIe 10 CIiI. 1 1u .1 1 ,kiibe;,1qIzcIItI Y mod Lf it’d by C (lorill t ŕ~ ;11( "n odl j, . i s j)1 ed U’ tm slil Iow~ waer eqtaL ions of Stokerx [4

Diagnostic and Condition Monitoring System Assessment for Army Helicopter Modular Turboshaft Engines.

DTIC Science & Technology

1980-10-01

from the sun. The longer bell mouth will also require that the water brake be located further from the engine, which mod- ifies the forward mount...unless there are over- riding considerations which are not readily quantifiable such as aircraft availabilit \\ and flight safety considerations...T M 1’ M Std (C) Moid. ’S-td C) M jSt- (C) 1I6’ 7 8 Prep and Install T700 4 4 5 4 5 4 5 4 Facility Check-Out and Water -Wash 1 1 /2 2 1 1-1 1!-󈧙 1

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

NASA Astrophysics Data System (ADS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-08-01

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

Theoretical and experimental power from large horizontal-axis wind turbines

NASA Technical Reports Server (NTRS)

Viterna, L. A.; Janetzke, D. C.

1982-01-01

A method for calculating the output power from large horizontal-axis wind turbines is presented. Modifications to the airfoil characteristics and the momentum portion of classical blade element-momentum theory are given that improve correlation with measured data. Improvement is particularly evident at low tip-speed ratios where aerodynamic stall can occur as the blade experiences high angles of attack. Output power calculated using the modified theory is compared with measured data for several large wind turbines. These wind turbines range in size from the DOE/NASA 100 kW Mod-0 (38 m rotor diameter) to the 2000 kW Mod-1 (61 m rotor diameter). The calculated results are in good agreement with measured data from these machines.

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

NASA Technical Reports Server (NTRS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.; Lipner, M. H.; Schornhorst, J. R.

1980-01-01

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

Méthodes de type éléments finis pour le calcul des champs électriques et magnétiques en électroencéphalographie et magnétoencéphalographie

NASA Astrophysics Data System (ADS)

Guérin, Christophe; Marin, Gildas; Garnero, Line; Meunier, Gérard

1997-12-01

So as to compute the electric potential and the flux density generated by the electrical activity of the brain, numerical methods based on the Finite Element Method have been developed. These methods, which can treat realistic head models and can take into account anisotropy of conductivity, for instance in the skull, are presented. Then two numerical examples are described: a spherical model and a realistic head model. Afin de calculer le potentiel électrique et l'induction créés par l'activité électrique du cerveau, nous avons développé des méthodes utilisant la Méthode des Éléments Finis. Ces méthodes, qui peuvent s'appliquer à des modèles réalistes de tête et qui permettent de tenir compte de la conductivité anisotrope de certains tissus comme l'os, sont présentées. Puis deux exemples numériques sont décrits : un modèle de sphères concentriques et un modèle réaliste de tête.

Evaluation of Microscopic Observation Drug Susceptibility (MODS) and the string test for rapid diagnosis of pulmonary tuberculosis in HIV/AIDS patients in Bolivia.

PubMed

Lora, Meredith H; Reimer-McAtee, Melissa J; Gilman, Robert H; Lozano, Daniel; Saravia, Ruth; Pajuelo, Monica; Bern, Caryn; Castro, Rosario; Espinoza, Magaly; Vallejo, Maya; Solano, Marco; Challapa, Roxana; Torrico, Faustino

2015-06-06

Tuberculosis (TB) is the most common opportunistic infection and the leading cause of death in HIV-positive people worldwide. Diagnosing TB is difficult, and is more challenging in resource-scarce settings where culture-based diagnostic methods rely on poorly sensitive smear microscopy by Ziehl-Neelsen stain (ZN). We performed a cross-sectional study examining the diagnostic utility of Microscopic Observation Drug Susceptibility liquid culture (MODS) versus traditional Ziehl-Neelsen staining (ZN) and Lowenstein Jensen culture (LJ) of pulmonary tuberculosis (TB) and multidrug-resistant tuberculosis (MDRTB) in HIV-infected patients in Bolivia. For sputum scarce individuals we assessed the value of the string test and induced sputum for TB diagnosis. The presence of Mycobacterium tuberculosis (Mtb) in the sputum of 107 HIV-positive patients was evaluated by ZN, LJ, and MODS. Gastric secretion samples obtained by the string test were evaluated by MODS in 102 patients. The TB-HIV co-infection rate of HIV patients with respiratory symptoms by sputum sample was 45 % (48/107); 46/48 (96 %) were positive by MODS, 38/48 (79 %) by LJ, and 30/48 (63 %) by ZN. The rate of MDRTB was 9 % (4/48). Median time to positive culture was 10 days by MODS versus 34 days by LJ (p < 0.0001). In smear-negative patients, MODS detected TB in 17/18 patients, compared to 11/18 by LJ (94.4 % vs 61.0 %, p = 0.03 %). In patients unable to produce a sputum sample without induction, the string test cultured by MODS yielded Mtb in of 9/11 (82 %) TB positive patients compared to 11/11 (100 %) with induced sputum. Of the 10 patients unable to produce a sputum sample, 4 were TB-positive by string test. MODS was faster and had a higher Mtb detection yield compared to LJ, with a greater difference in yield between the two in smear-negative patients. The string test is a valuable diagnostic technique for HIV sputum-scarce or sputum-absent patients, and should be considered as an alternative test to induced sputum to obtain sample for Mtb in resource-limited settings. Nine percent of our TB+ patients had MDRTB, which reinforces the need for rapid detection with direct drug susceptibility testing in HIV patients in Bolivia.

Sensitivity of MODIS evapotranspiration algorithm (MOD16) to the acuracy of meteorological data and land use and land cover parameterization

NASA Astrophysics Data System (ADS)

Ruhoff, Anderson; Santini Adamatti, Daniela

2017-04-01

MODIS evapotranspiration (MOD16) is currently available with 1 km of spatial resolution over 109.03 Million km2 of vegetated land surface areas and this information is widely used to evaluate the linkages between hydrological, energy and carbon cycles. The algorithm is driven by meteorological reanalysis data and MODIS remotely-sensed data, which include land use and land cover classification (MCD12Q1), leaf area index (LAI) and fraction of absorbed photosynthetically active radiation (FPAR) (MOD15A2) and albedo (MOD43b3). For calibration and parameterization, the algorithm uses a Biome Property Look-up Table (BPLUT) based on MCD12Q1 land cover classification. Several studies evaluated MOD16 accuracy using evapotranspiration measurements and water balance analysis, showing that this product can reproduce global evapotranspiration effectively under a variety climate condition, from local to wide-basin scale, with uncertainties up to 25%. In this study, we evaluated the sensitivity of MOD16 algorithm to land use and land cover parameterization and to meteorological data. Considering that MCD12Q1 has an accuracy between 70 and 85% at continental scale, we changed land cover parametererization to understand the influence of land use and land cover classification on MOD16 evapotranspiration estimations. Knowing that meteorological reanalysis data also have uncertainties (mostly related to the coarse spatial resolution), we compared MOD16 evapotranspiration driven by observed meteorological data to those driven by the reanalysis data. Our analysis were carried in South America, with evapotranspiration and meteorological measurements from the Large-Scale Biosphere-Atmosphere Experiment in Amazonia (LBA) at 8 different sites, including tropical rainforest, tropical dry forest, selective logged forest, seasonal flooded forest and pasture/agriculture. Our results indicate that land use and land cover classification has a strong influence on MOD16 algorithm. The use of incorrect parametererization due to land use and land cover misclassification can introduce large erros in estimates of evapotranspiration. We also found that the biases in meteorological reanalysis data can introduce considerable errors into the estimations. Overall, there is a significant potential for mapping and monitoring global evapotranspiration using MODIS remotely-sensed images combined to meteorological reanalysis data.

Soluble tumor necrosis factor receptor p55 predicts cytokinemia and systemic inflammatory response after cardiopulmonary bypass.

PubMed

el-Barbary, Mahmoud; Khabar, Khalid S A

2002-08-01

To examine the behavior of soluble tumor necrosis factor (TNF) receptors in circulation before and after cardiopulmonary bypass and the relationship to the development of cytokinemia and acute complications comprising systemic inflammatory response syndrome (SIRS) and multiple organ dysfunction syndrome (MODS). The predictive value of soluble TNF receptor is assessed herein. Prospective study comparing prebypass and postbypass levels in patients with and without complications indicative of SIRS and MODS. Cardiac surgical intensive care unit in a tertiary care hospital. A total of 20 pediatric patients who underwent cardiopulmonary bypass during open heart surgery. Blood samples were collected from catheters before and 2 hrs and 24 hrs after the onset of bypass. We measured plasma levels of soluble TNF receptors by using enzyme-linked immunosorbent assay in 20 patients before and after cardiopulmonary bypass. Clinical data, including duration of bypass and tests or signs indicative of SIRS/MODS, were collected. Soluble TNF receptor I (p55 sR), significantly increased (2241 +/- 312 pg/mL) at 2 hrs after bypass (p <.0005) and remained elevated (2826 +/- 695 pg/mL) at 1 day after bypass (p <.005) when compared with prebypass levels (725 +/- 130 pg/mL). Patients with the acute complications of SIRS/MODS had a higher ratio of postbypass to prebypass p55 sR levels (5.0-fold, p <.001) when compared with patients with no SIRS/MODS (1.75-fold). Remarkably, before surgery, levels of TNF p55 sR predict both cytokinemia (r =.67 to.73, p <.05) and SIRS/MODS (p <.01). The prebypass levels of TNF p55 sR were consistently higher (range, 1000-1400 pg/mL) in patients who subsequently developed SIRS/MODS than the levels (range, 400-570 pg/mL) in patients who did not develop SIRS/MODS. Hypotension, respiratory dysfunctions, and coagulopathy were particularly more prevailing (p <.005) among the complications that were associated with high prebypass levels of TNF p55 sR. Soluble TNF receptor p55 can be employed as a predictive marker for cytokinemia and the development of SIRS/MODS that may arise from a major insult to the body such as cardiopulmonary bypass.

Snow fraction products evaluation with Landsat-8/OLI data and its spatial scale effects over the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Jiang, L.

2016-12-01

Snow cover is one of important elements in the water supply of large populations, especially in those downstream from mountainous watershed. The cryosphere process in the Tibetan Plateau is paid much attention due to rapid change of snow amount and cover extent. Snow mapping from MODIS has been increased attention in the study of climate change and hydrology. But the lack of intensive validation of different snow mapping methods especially at Tibetan Plateau hinders its application. In this work, we examined three MODIS snow products, including standard MODIS fractional snow product (MOD10A1) (Kaufman et al., 2002; Salomonson & Appel, 2004, 2006), two other fractional snow product, MODSCAG (Painter et al., 2009) and MOD_MESMA (Shi, 2012). Both these two methods are based on spectral mixture analysis. The difference between MODISCAG and MOD_MESMA was the endmember selection. For MODSCAG product, snow spectral endmembers of varying grain size was obtained both from a radiative transfer model and spectra of vegetation, rock and soil collected in the field and laboratory. MOD_MESMA was obtained from automated endmember extraction method using linear spectral mixture analysis. Its endmembers are selected in each image to enhance the computational efficiency of MESMA (Multiple Endmember Spectral Analysis). Landsat-8 Operatinal Land Imager (OLI) data from 2013-2015 was used to evaluate the performance of these three snow fraction products in Tibetan Plateau. The effect of land cover types including forest, grass and bare soil was analyzed to evaluate three products. In addition, the effects of relatively flat surface in internal plateau and high mountain areas of Himalaya were also evaluated on the impact of these snow fraction products. From our comparison, MODSCAG and MOD10A1 overestimated snow cover, while MOD_MESMA underestimated snow cover. And RMSE of MOD_MESMA at each land cover type including forest, grass and mountain area decreased with the spatial resolution increasing from 500m, 1km, 2km to 5km. The RMSE of MODSCAG and MOD10A1 is very similar. In Himalaya area, these two RMSEs of MODSCAG and MOD10A1 increased with the spatial resolution increasing from 500m to 5km. For forest, grass and bare soil, RMSE decreased from 500m to 1km, then increased from 1km to 2km.