Faraday Rotation and Models for the Plasma Structure of the Solar Corona

NASA Astrophysics Data System (ADS)

Mancuso, Salvatore; Spangler, Steven R.

2000-08-01

Faraday rotation observations of polarized radiation from natural radio sources are unique among remote diagnostics of the solar corona in that they provide information on the coronal magnetic field. Dual frequency radio polarization measurements yield the rotation measure, a quantity that is proportional to the integral along the line of sight of the product of the electron density and the line-of-sight component of the magnetic field. We made linear polarization observations with the NRAO Very Large Array of 13 polarized radio sources occulted by the solar corona. The observations were made at frequencies of 1465 and 1665 MHz on four days in 1997 May and cover a 20 day period, sampling elongations ranging from about 5 to 14 Rsolar. The magnitudes of the rotation measures observed range from about 11 to 0 rad m-2. The relatively low values for the rotation measures are due to the solar minimum configuration of the corona at the time of the observations, with the lines of sight to the sources generally not crossing sector boundaries. The largest rotation measure was observed for the extended radio source 3C 79 on 1997 May 11 and corresponds to a case in which the line of sight passed next to the streamer belt at small solar elongations. We have developed a three-dimensional model of the solar corona that is in excellent agreement with the observed rotation measures, as well as being completely consistent with other coronal diagnostics such as coronagraph images. In particular, our observations support the coronal magnetic field model of Pätzold et al. (1987) they would be inconsistent with coronal magnetic fields significantly weaker or stronger than this model. The plasma density distribution in the corona is successfully modeled by a dense streamer belt component and a more tenuous coronal hole component. Details of these models are given in § 3 of this paper. The principal disagreement between the model and observations occurs for three lines of sight for which the model predicts nearly zero rotation measure but for which we measure small but significant values of -1 to -2 rad m-2. These lines of sight passed over the solar polar regions. We discuss the possibility that these residual rotation measures are due to static coronal plasma structures, not described by global coronal models, or to very long wavelength coronal Alfvén waves. Fluctuations in the rotation measure on timescales of a few hours were observed for some sources and not others. When detected, they were of order 1-2 rad m-2 and occurred on timescales of several hours.

Density Fluctuations in a Polar Coronal Hole

NASA Astrophysics Data System (ADS)

Hahn, Michael; D’Huys, Elke; Savin, Daniel Wolf

2018-06-01

We have measured the root-mean-square (rms) amplitude of intensity fluctuations, ΔI, in plume and interplume regions of a polar coronal hole. These intensity fluctuations correspond to density fluctuations. Using data from the Sun Watcher using the Active Pixel System detector and Image Processing on the Project for Onboard Autonomy (Proba2), our results extend up to a height of about 1.35 R ⊙. One advantage of the rms analysis is that it does not rely on a detailed evaluation of the power spectrum, which is limited by noise levels to low heights in the corona. The rms approach can be performed up to larger heights where the noise level is greater, provided that the noise itself can be quantified. At low heights, both the absolute ΔI, and the amplitude relative to the mean intensity, ΔI/I, decrease with height. However, starting at about 1.2 R ⊙, ΔI/I increases, reaching 20%–40% by 1.35 R ⊙. This corresponds to density fluctuations of Δn e/n e ≈ 10%–20%. The increasing relative amplitude implies that the density fluctuations are generated in the corona itself. One possibility is that the density fluctuations are generated by an instability of Alfvén waves. This generation mechanism is consistent with some theoretical models and with observations of Alfvén wave amplitudes in coronal holes. Although we find that the energy of the observed density fluctuations is small, these fluctuations are likely to play an important indirect role in coronal heating by promoting the reflection of Alfvén waves and driving turbulence.

Explosive Chromospheric Evaporation and Warm Rain in a GOES C3 Flare Observed by IRIS, Hinode/EIS, and RHESSI

NASA Astrophysics Data System (ADS)

Brosius, J. W.; Inglis, A. R.

2017-12-01

IRIS and Hinode/EIS observed a C3.1 flare in AR 12002 in stare mode on 2014 March 15.GOES observed the flare to start at 00:21:35 UT and peak at 00:26:30 UT. The IRIS slitwas pointed near the center of the flare while the EIS slit was pointed 35 arcsec westof the IRIS slit. About 4 minutes before the GOES flare start, the C II and Si IV lineintensities observed by IRIS became (and remained) significantly greater than theirpre-flare average values; this indicates that the flare had begun and that thechromosphere and transition region were involved. IRIS first detected significant,blueshifted Fe XXI emission at 00:22:42 UT, by which time the C II and Si IV lineintensities had increased by factors around 100 and their profiles were significantlyredshifted. This combination of simultaneous, cospatial blueshifted Fe XXI emissionwith redshifted C II and Si IV emission indicates explosive chromospheric evaporation.SDO's HMI observed a localized area of enhanced magnetic field strength toward thesouthernmost portion of the EIS slit's position that appears to be connected to theflare site by faint loops evident in AIA 131 A emission. EIS spectra at this locationreveal intensity enhancements by factors up to about 1.7 in the Fe XIV and Fe XVI lineemission, and the emergence of faint Fe XXIII emission that is too weak to measurevelocities. Emission lines from the two coronal ions show redshifts of about 9 km/saround 00:24:00 UT. The density sensitive line intensity ratio of Fe XIV 264.7/274.2observed by EIS reveals an increase of electron density from (1.03+/-0.20)X10^9 /cm^3before the flare to (3.58+/-0.68)X10^9 /cm^3 during the flare. This combination ofredshifted coronal line emission and increased coronal electron density is consistentwith explosively evaporated flare material observed by IRIS falling as warm rain andaccumulating in the remote area observed by EIS. A thermal/nonthermal fit to the hardX-ray spectrum observed by RHESSI yields a nonthermal energy injection rate of4.9X10^26 ergs/s; combining this with an estimated injection area of (2.1+/-1.7)X10^17cm^2 based on IRIS slit-jaw images, we estimate a HXR beam energy flux of(6.7+/-5.5)X10^9 ergs/cm^2/s, a wide range whose larger values are consistent withexplosive chromospheric evaporation.

Evaluation of implants coated with rhBMP-2 using two different coating strategies: a critical-size supraalveolar peri-implant defect study in dogs.

PubMed

Lee, Jaebum; Decker, John F; Polimeni, Giuseppe; Cortella, Carlo Alberto; Rohrer, Michael D; Wozney, John M; Hall, Jan; Susin, Cristiano; Wikesjö, Ulf M E

2010-06-01

Implants coated with recombinant human bone morphogenetic protein-2 (rhBMP-2) induce relevant bone formation but also resident bone remodelling. To compare the effect of implants fully or partially coated with rhBMP-2 on new bone formation and resident bone remodelling. Twelve, male, adult, Hound Labrador mongrel dogs were used. Critical-size, supraalveolar, peri-implant defects received titanium porous oxide surface implants coated in their most coronal aspect with rhBMP-2 (coronal-load/six animals) or by immersion of the entire implant in an rhBMP-2 solution (soak-load/six animals) for a total of 30 mug rhBMP-2/implant. All implants were air-dried. The animals were euthanized at 8 weeks for histometric evaluation. Clinical healing was uneventful. Supraalveolar bone formation was not significantly affected by the rhBMP-2 application protocol. New bone height and area averaged (+/- SE) 3.4 +/- 0.2 versus 3.5 +/- 0.4 mm and 2.6 +/- 0.4 versus 2.5 +/- 0.7 mm(2) for coronal-load and soak-load implants, respectively (p>0.05). The corresponding bone density and bone-implant contact (BIC) recordings averaged 38.0 +/- 3.8%versus 34.4 +/- 5.6% and 25.0 +/- 3.8%versus 31.2 +/- 3.3% (p>0.05). In contrast, resident bone remodelling was significantly influenced by the rhBMP-2 application protocol. Bone density outside the implants threads averaged 74.7 +/- 3.8% and 50.8 +/- 4.1% for coronal-load and soak-load implants, respectively (p<0.05); bone density within the thread area averaged 51.8 +/- 1.2% and 37.8 +/- 2.9%, and BIC 70.1 +/- 6.7% and 43.3 +/- 3.9% (p<0.05). Local application of rhBMP-2 appears to be a viable technology to support local bone formation and osseointegration. Coronal-load implants obviate resident bone remodelling without compromising new bone formation.

The Three-part Structure of a Filament-unrelated Solar Coronal Mass Ejection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, H. Q.; Chen, Y.; Wang, B.

Coronal mass ejections (CMEs) often exhibit the typical three-part structure in the corona when observed with white-light coronagraphs, i.e., the bright leading front, dark cavity, and bright core, corresponding to a high-low-high density sequence. As CMEs result from eruptions of magnetic flux ropes (MFRs), which can possess either lower (e.g., coronal-cavity MFRs) or higher (e.g., hot-channel MFRs) density compared to their surroundings in the corona, the traditional opinion regards the three-part structure as the manifestations of coronal plasma pileup (high density), coronal-cavity MFR (low density), and filament (high density) contained in the trailing part of MFR, respectively. In this paper,more » we demonstrate that filament-unrelated CMEs can also exhibit the classical three-part structure. The observations were made from different perspectives through an event that occurred on 2011 October 4. The CME cavity corresponds to the low-density zone between the leading front and the high-density core, and it is obvious in the low corona and gradually becomes fuzzy when propagating outward. The bright core corresponds to a high-density structure that is suggested to be an erupting MFR. The MFR is recorded from both edge-on and face-on perspectives, exhibiting different morphologies that are due to projection effects. We stress that the zone (MFR) with lower (higher) density in comparison to the surroundings can appear as the dark cavity (bright core) when observed through white-light coronagraphs, which is not necessarily the coronal-cavity MFR (erupted filament).« less

Coronal Structures in Cool Stars: XMM-NEWTON Hybrid Stars and Coronal Evolution

NASA Technical Reports Server (NTRS)

Dupree, Andrea K.; Mushotzky, Richard (Technical Monitor)

2003-01-01

This program addresses the evolution of stellar coronas by comparing a solar-like corona in the supergiant Beta Dra (G2 Ib-IIa) to the corona in the allegedly more evolved state of a hybrid star, alpha TrA (K2 II-III). Because the hybrid star has a massive wind, it appears likely that the corona will be cooler and less dense as the magnetic loop structures are no longer closed. By analogy with solar coronal holes, when the topology of the magnetic field is configured with open magnetic structures, both the coronal temperature and density are lower than in atmospheres dominated by closed loops. The hybrid stars assume a pivotal role in the definition of coronal evolution, atmospheric heating processes and mechanisms to drive winds of cool stars. We are attempting to determine if this model of coronal evolution is correct by using XMM-NEWTON RGS spectra for the 2 targets we were allocated through the Guest Observer program.

Imaging spectroscopy of type U and J solar radio bursts with LOFAR

NASA Astrophysics Data System (ADS)

Reid, Hamish A. S.; Kontar, Eduard P.

2017-10-01

Context. Radio U-bursts and J-bursts are signatures of electron beams propagating along magnetic loops confined to the corona. The more commonly observed type III radio bursts are signatures of electron beams propagating along magnetic loops that extend into interplanetary space. Given the prevalence of solar magnetic flux to be closed in the corona, why type III bursts are more frequently observed than U-bursts or J-bursts is an outstanding question. Aims: We use Low-Frequency Array (LOFAR) imaging spectroscopy between 30-80 MHz of low-frequency U-bursts and J-bursts, for the first time, to understand why electron beams travelling along coronal loops produce radio emission less often. Radio burst observations provide information not only about the exciting electron beams but also about the structure of large coronal loops with densities that are too low for standard extreme ultraviolet (EUV) or X-ray analysis. Methods: We analysed LOFAR images of a sequence of two J-bursts and one U-burst. The different radio source positions were used to model the spatial structure of the guiding magnetic flux tube and then deduce the energy range of the exciting electron beams without the assumption of a standard density model. We also estimated the electron density along the magnetic flux rope and compared it to coronal models. Results: The radio sources infer a magnetic loop that is 1 solar radius in altitude with the highest frequency sources starting around 0.6 solar radii. Electron velocities were found between 0.13 c and 0.24 c with the front of the electron beam travelling faster than the back of the electron beam. The velocities correspond to energy ranges within the beam from 0.7-11 keV to 0.7-43 keV. The density along the loop is higher than typical coronal density models and the density gradient is smaller. Conclusions: We found that a more restrictive range of accelerated beam and background plasma parameters can result in U-bursts or J-bursts, causing type III bursts to be more frequently observed. The large instability distances required before Langmuir waves are produced by some electron beams, and the small magnitude of the background density gradients makes closed loops less facilitative for radio emission than loops that extend into interplanetary space.

Investigating the Response of Loop Plasma to Nanoflare Heating Using RADYN Simulations

NASA Astrophysics Data System (ADS)

Polito, V.; Testa, P.; Allred, J.; De Pontieu, B.; Carlsson, M.; Pereira, T. M. D.; Gošić, Milan; Reale, Fabio

2018-04-01

We present the results of 1D hydrodynamic simulations of coronal loops that are subject to nanoflares, caused by either in situ thermal heating or nonthermal electron (NTE) beams. The synthesized intensity and Doppler shifts can be directly compared with Interface Region Imaging Spectrograph (IRIS) and Atmospheric Imaging Assembly (AIA) observations of rapid variability in the transition region (TR) of coronal loops, associated with transient coronal heating. We find that NTEs with high enough low-energy cutoff ({E}{{C}}) deposit energy in the lower TR and chromosphere, causing blueshifts (up to ∼20 km s‑1) in the IRIS Si IV lines, which thermal conduction cannot reproduce. The {E}{{C}} threshold value for the blueshifts depends on the total energy of the events (≈5 keV for 1024 erg, up to 15 keV for 1025 erg). The observed footpoint emission intensity and flows, combined with the simulations, can provide constraints on both the energy of the heating event and {E}{{C}}. The response of the loop plasma to nanoflares depends crucially on the electron density: significant Si IV intensity enhancements and flows are observed only for initially low-density loops (<109 cm‑3). This provides a possible explanation of the relative scarcity of observations of significant moss variability. While the TR response to single heating episodes can be clearly observed, the predicted coronal emission (AIA 94 Å) for single strands is below current detectability and can only be observed when several strands are heated closely in time. Finally, we show that the analysis of the IRIS Mg II chromospheric lines can help further constrain the properties of the heating mechanisms.

Further Analysis of the Crouzon Mouse, Effects of the FGFR2C342Y Mutation are Cranial Bone Dependent

PubMed Central

Liu, Jin; Nam, Hwa Kyung; Wang, Estee; Hatch, Nan E.

2013-01-01

Crouzon syndrome is a debilitating congenital disorder involving abnormal craniofacial skeletal development caused by mutations in Fibroblast Growth Factor Receptor-2 (FGFR2). Phenotypic expression in humans exhibits an autosomal dominant pattern that commonly involves premature fusion of the coronal suture (craniosynostosis) and severe midface hypoplasia. To further investigate biologic mechanisms by which the Crouzon syndrome associated FGFR2C342Y mutation leads to abnormal craniofacial skeletal development we created congenic BALB/c FGFR2C342Y/+ mice. Here we show that BALB/c FGFR2C342Y/+ mice have a consistent craniofacial phenotype including partial fusion of the coronal and lambdoid sutures, intersphenoidal synchondrosis and multiple facial bones, with minimal fusion of other craniofacial sutures. This phenotype is similar to the classic and less severe form of Crouzon syndrome that involves significant midface hypoplasia with limited craniosynostosis. Linear and morphometric analyses demonstrate that FGFR2C342Y/+ mice on the BALB/c genetic background differ significantly in form and shape from their wild type littermates, and that in this genetic background the FGFR2C342Y mutation preferentially effects some craniofacial bones and sutures over others. Analysis of cranial bone cells indicates that the FGFR2C342Y mutation promotes aberrant osteoblast differentiation and increased apoptosis that is more severe in frontal than parietal bone cells. Additionally, FGFR2C342Y/+ frontal but not parietal bones exhibit significantly diminished bone volume and density compared to wild type mice. These results confirm that FGFR2-associated craniosynostosis occurs in association with diminished cranial bone tissue and may provide a potential biologic explanation for the clinical finding of phenotype consistency that exists between many Crouzon syndrome patients. PMID:23358860

Reciprocal Changes in Sagittal Alignment in Adolescent Idiopathic Scoliosis Patients Following Strategic Pedicle Screw Fixation.

PubMed

Dumpa, Srikanth Reddy; Shetty, Ajoy Prasad; Aiyer, Siddharth N; Kanna, Rishi Mugesh; Rajasekaran, S

2018-04-01

Retrospective observational study. To analyze the effect of low-density (LD) strategic pedicle screw fixation on the correction of coronal and sagittal parameters in adolescent idiopathic scoliosis (AIS) patients. LD screw fixation achieves favorable coronal correction, but its effect on sagittal parameters is not well established. AIS is often associated with decreased thoracic kyphosis (TK), and the use of multi-level pedicle screws may result in further flattening of the sagittal profile. A retrospective analysis was performed on 92 patients with AIS to compare coronal and sagittal parameters preoperatively and at 2-year follow-up. All patients underwent posterior correction via LD strategic pedicle screw fixation. Radiographs were analyzed for primary Cobb angle (PCA), coronal imbalance, cervical sagittal angle (CSA), TK, lumbar lordosis (LL), pelvic incidence, pelvic tilt (PT), sacral slope (SS), C7 plumb line, spino-sacral angle, curve flexibility, and screw density. PCA changed significantly from 57.6°±13.9° to 19°±8.4° ( p <0.0001) with 67% correction, where the mean curve flexibility was 41% and screw density was 68%. Regional sagittal parameters did not change significantly, including CSA (from 10.76° to 10.56°, p =0.893), TK (from 24.4° to 22.8°, p =0.145), and LL (from 50.3° to 51.1°, p =0.415). However, subgroup analysis of the hypokyphosis group (<10°) and the hyperkyphosis group (>40°) showed significant correction of TK ( p <0.0001 in both). Sacro-pelvic parameters showed a significant decrease of PT and increase of SS, suggesting a reduction in pelvic retroversion SS (from 37° to 40°, p =0.0001) and PT (from 15° to 14°, p =0.025). LD strategic pedicle screw fixation provides favorable coronal correction and improves overall sagittal sacro-pelvic parameters. This technique does not cause significant flattening of TK and results in a favorable restoration of TK in patients with hypokyphosis or hyperkyphosis.

Reciprocal Changes in Sagittal Alignment in Adolescent Idiopathic Scoliosis Patients Following Strategic Pedicle Screw Fixation

PubMed Central

Dumpa, Srikanth Reddy; Aiyer, Siddharth N.; Kanna, Rishi Mugesh; Rajasekaran, S

2018-01-01

Study Design Retrospective observational study. Purpose To analyze the effect of low-density (LD) strategic pedicle screw fixation on the correction of coronal and sagittal parameters in adolescent idiopathic scoliosis (AIS) patients. Overview of Literature LD screw fixation achieves favorable coronal correction, but its effect on sagittal parameters is not well established. AIS is often associated with decreased thoracic kyphosis (TK), and the use of multi-level pedicle screws may result in further flattening of the sagittal profile. Methods A retrospective analysis was performed on 92 patients with AIS to compare coronal and sagittal parameters preoperatively and at 2-year follow-up. All patients underwent posterior correction via LD strategic pedicle screw fixation. Radiographs were analyzed for primary Cobb angle (PCA), coronal imbalance, cervical sagittal angle (CSA), TK, lumbar lordosis (LL), pelvic incidence, pelvic tilt (PT), sacral slope (SS), C7 plumb line, spino-sacral angle, curve flexibility, and screw density. Results PCA changed significantly from 57.6°±13.9° to 19°±8.4° (p <0.0001) with 67% correction, where the mean curve flexibility was 41% and screw density was 68%. Regional sagittal parameters did not change significantly, including CSA (from 10.76° to 10.56°, p =0.893), TK (from 24.4° to 22.8°, p =0.145), and LL (from 50.3° to 51.1°, p =0.415). However, subgroup analysis of the hypokyphosis group (<10°) and the hyperkyphosis group (>40°) showed significant correction of TK (p <0.0001 in both). Sacro-pelvic parameters showed a significant decrease of PT and increase of SS, suggesting a reduction in pelvic retroversion SS (from 37° to 40°, p =0.0001) and PT (from 15° to 14°, p =0.025). Conclusions LD strategic pedicle screw fixation provides favorable coronal correction and improves overall sagittal sacro-pelvic parameters. This technique does not cause significant flattening of TK and results in a favorable restoration of TK in patients with hypokyphosis or hyperkyphosis. PMID:29713412

Coronal imbalance in Lenke 5C adolescent idiopathic scoliosis regarding selecting the lowest instrumented vertebra: Lower-end vertebra versus lower-end vertebra +1 in posterior fusion.

PubMed

Hu, Bowen; Yang, Xi; Yang, Huiliang; Liu, Limin; Chen, Peiran; Wang, Linnan; Zhu, Ce; Zhou, Chunguang; Song, Yueming

2018-06-18

Choosing the fusion level for posterior fusion in Lenke 5C adolescent idiopathic scoliosis patients is highly associated with coronal balance. Previous studies indicated that in patients with lowest end vertebra tilt > 25°, surgeons could extend distal fusion to avoid coronal imbalance. This study aimed to assess the risk factors for coronal imbalance in Lenke 5C scoliosis, and to discuss how to select fusion level. We reviewed 59 Lenke 5C AIS patients in one institution with at least 2-years' follow-up from 2010 through 2015. Preoperative, and 3-month and 2-year postoperative follow-up radiographs were measured using a number of specific measurements related to coronal balance. Patients were categorized into an LEV group and an LEV+1 group. Coronal imbalance was found in 6/31 patients in the LEV+1 group at final follow-up , and not in the LEV-group at the first or final follow-up. The C7 plumb line shifted to the convex side of the central sacral vertical line in 47/59 patients, including all of the 19 CIB patients after surgery. Patients who underwent fusion at LEV+1 with > 25° LEV tilt also showed poor results regarding coronal imbalance. Statistically, coronal balance at the final follow-up was correlated with preoperative bending lumbosacral hemi-curve (p=0.002) and all of the 6 patients with CIB had bending lumbosacral hemi-curve exceeds 15°. No significant difference were found in SRS-22 scores between the two groups at 2-year-follow-up. Distal fusion extension at LEV+1 is more likely to result in coronal imbalance at the first and final follow-up, especially when bending lumbosacral hemi-curve exceeds 15°. Fusion at LEV+1 should not be chosen when LEV is at L4. Copyright © 2018. Published by Elsevier Inc.

Hybrid Stars and Coronal Evolution

NASA Technical Reports Server (NTRS)

Mushotzky, Richard (Technical Monitor); Dupree, Andrea K.

2004-01-01

This program addresses the evolution of stellar coronas by comparing a solar-like corona in the supergiant Dra (G2 Ib-IIa) to the corona in the allegedly more evolved state of a hybrid star, TrA (K2 11-111). Because the hybrid star has a massive wind, it appears likely that the corona will be cooler and less dense as the magnetic loop structures are no longer closed. By analogy with solar coronal holes, when the topology of the magnetic field is configured with open magnetic structures, both the coronal temperature and density are lower than in atmospheres dominated by closed loops. The hybrid stars assume a pivotal role in the definition of coronal evolution, atmospheric heating processes and mechanisms to drive winds of cool stars.

The temperature structure, mass, and energy flow in the corona and inner solar wind

NASA Technical Reports Server (NTRS)

Withbroe, George L.

1988-01-01

Remote-sensing and in situ data are used to constrain a radiative energy balance model in order to study the radial variations of coronal temperatures, densities, and outflow speeds in several types of coronal holes and in an unstructured quiet region of the corona. A one-fluid solar wind model is used which takes into account the effects of radiative and inward conductive losses in the low corona and the chromospheric-coronal transition region. The results show that the total nonradiative energy input in magnetically open coronal regions is 5 + or - 10 to the 5th ergs/sq cm, and that most of the energy heating the coronal plasma is dissipated within 2 solar radii of the solar surface.

Supra-acetabular line is better than supra-iliac line for coronal balance referencing-a study of perioperative whole spine X-rays in degenerative lumbar scoliosis and ankylosing spondylitis patients.

PubMed

Hey, Hwee Weng Dennis; Kim, Cheung-Kue; Lee, Won-Gyu; Juh, Hyung-Suk; Kim, Ki-Tack

2017-12-01

The aim of spinal deformity correction is to restore the spine's functional alignment by balancing it in both the sagittal and coronal planes. Regardless of posture, the ideal coronal profile is straight, and therefore readily assessable. This study compares two radiological methods to determine which better predicts postoperative standing coronal balance. We conducted a single-center, radiographic comparative study between 2011 and 2015. A total of 199 patients with a mean age of 55.1 years were studied. Ninety patients with degenerative lumbar scoliosis (DLS) and 109 ankylosing spondylitis (AS) were treated with posterior surgery during this period. Baseline clinical and radiographic parameters (sagittal and coronal) were recorded. Comparison was performed between the new supra-acetabular line (central sacral vertical line [CSVL1]) and conventional supra-iliac line (CSVL2) perpendicular methods of coronal balance assessment. These methods were also compared with the gold standard standing C7 plumb line. Each patient underwent standardized operative procedures and had perioperative spine X-rays obtained for assessment of spinal balance. Adjusted multivariate analysis was used to determine predictors of coronal balance. Significant differences in baseline characteristics (age, gender, and radiographic parameters) were found between patients with DLS and AS. CSVL1, CSVL2, and C7 plumb line differed in all the perioperative measurements. These three radiological methods showed a mean right coronal imbalance for both diagnoses in all pre-, intra-, and postoperative radiographs. The magnitude of imbalance was the greatest for CSVL2 followed by CSVL1 and subsequently the C7 plumb line. A larger discrepancy between CSVL and C7 plumb line measurements intraoperatively than those postoperatively suggests a postural effect on these parameters, which is greater for CSVL2. Multivariate analysis identified that in DLS, the preoperative C7 plumb line was predictive of its postoperative value. CSVL1, but not CSVL2, was predictive of the postoperative C7 plumb line in patients with AS. The supra-acetabular line (CSVL1) is better, although not ideal, as compared with the supra-iliac line (CSVL2) in determining coronal balance. Because CSVL1 still cannot be relied on with a high predictive value, it is imperative that future studies continue to identify better intraoperative markers for achieving coronal balance. Copyright © 2017 Elsevier Inc. All rights reserved.

Asymmetric C7 pedicle subtraction osteotomy for correction of rigid cervical coronal imbalance secondary to post-traumatic heterotopic ossification: a case report, description of a novel surgical technique, and literature review.

PubMed

Theologis, Alexander A; Bellevue, Kate D; Qamirani, Erion; Ames, Christopher P; Deviren, Vedat

2017-05-01

Deformities of the cervical spine are uncommon in the coronal plane. In this report, a unique case of a 31-year-old male with a fixed, 30° left coronal deformity due to heterotopic ossification 3 years status post poly-trauma was treated with an asymmetric C7 pedicle subtraction osteotomy (PSO). Case report. Pre-operatively, the patient had a fixed 45-degree left tilt of his neck and radiographs demonstrated a rigid 30° scoliosis, 7 cm coronal imbalance, and 4 cm negative sagittal balance, diffuse bridging bone between the spinous processes and the facet joints of C5 to T1 bilaterally. An asymmetric C7 PSO with C2-T3 posterior spinal fusion was completed without complication. There was residual 9° coronal deformity, 2.9 cm left coronal imbalance, and 2.3 cm sagittal imbalance. He had a marked improvement in his function, as assessed by the SF-36 physical component score (pre-op 31.1; post-op 44.7) and mental component score (pre-op 46.0; post-op 66.8). Post-operatively, neck disability index scores also improved (pre-op 38; post-op 16). Although the patient passed away from a drug overdose 14 months post-operatively, he did not report neck pain, he had not sought evaluation from another physician for his neck, and he had not undergone a subsequent neck operation before his passing. In this one patient, an asymmetric C7 PSO was performed safely. While it was effective in addressing a fixed cervical coronal imbalance, its efficacy and safety profile should be confirmed in larger cohorts.

Spontaneous correction of coronal imbalance after selective thoracolumbar-lumbar fusion in patients with Lenke-5C adolescent idiopathic scoliosis.

PubMed

Hwang, Chang Ju; Lee, Choon Sung; Kim, Hyojune; Lee, Dong-Ho; Cho, Jae Hwan

2018-03-22

Coronal imbalance is a complication of corrective surgeries in adolescent idiopathic scoliosis (AIS). However, few studies about immediate coronal decompensation in Lenke-5C curves have reported its incidence, prognosis, and related factors. To evaluate the development of coronal imbalance after selective thoracolumbar-lumbar (TL/L) fusion (SLF) in Lenke-5C AIS, and to reveal related factors. Retrospective comparative study. This study included 50 consecutive patients with Lenke-5C AIS who underwent SLF at a single center. Whole-spine anteroposterior and lateral radiographs were used to measure radiological parameters. Patients were divided into two groups according to the presence or absence of coronal imbalance (distance between C7 plumb line and central sacral vertical line >2 cm) in the early (1 month) postoperative period. Various radiological parameters were statistically compared between groups. Of the patients, 28% (14 of 50) showed coronal imbalance in the early postoperative period; however, most of them (13 of 14) showed spontaneous correction during follow-up. The development of coronal imbalance was related to less flexibility of the TL/L curve (51.3% vs. 52.6%, p=.040), greater T10-L2 kyphosis (11.7° vs. 6.4°, p=.034), and greater distal junctional angle (6.0° vs. 3.7°, p=.025) in preoperative radiographs. Lowermost instrumented vertebra (LIV) tilt was greater in the decompensation [+] group in the early postoperative period (8.8° vs. 4.4°, p=.009). However, this difference disappeared in final follow-up with the decrease of LIV tilt in the decompensation [+] group. Less flexibility of the TL/L curve, greater TL kyphosis, and greater distal junctional angle preoperatively were predictive factors for immediate coronal imbalance in Lenke-5C curves. Although coronal imbalance was frequently detected in the early postoperative period after SLF, it was mostly corrected spontaneously with a decrease of LIV tilt. Thus, SLF for Lenke-5C curves can be a good option regardless of the possible coronal imbalance in the early postoperative period. Copyright © 2018 Elsevier Inc. All rights reserved.

On the density and field sensitivities of dielectronic recombination. [rates in coronal plasmas of late stars and sun

NASA Technical Reports Server (NTRS)

Reisenfeld, Daniel B.; Raymond, John C.; Young, Albert R.; Kohl, John L.

1992-01-01

Dielectronic recombination dominates the recombination rates of most ions in coronal plasmas at their temperatures of peak concentration. Because dielectronic recombination goes by way of high nl doubly excited levels, it is susceptible to collisional excitation and ionization, leading to a decreased rate. On the other hand, theoretical studies show that Stark mixing of the nl levels by a modest electric field enhances the dielectronic recombination rate severalfold. The ionization balance is computed here as as function of density, and it is found that the new results require increased emission measures to match the C IV emission line intensities observed in the sun and in late-type stars. They also make it more difficult to interpret the overall EUV emission line spectrum of the sun.

Infrared coronal emission lines and the possibility of their maser emission in Seyfert nuclei

NASA Technical Reports Server (NTRS)

Greenhouse, Matthew A.; Feldman, Uri; Smith, Howard A.; Klapisch, Marcel; Bhatia, Anand K.; Bar-Shalom, Abi

1993-01-01

Energetic emitting regions have traditionally been studied via x-ray, UV and optical emission lines of highly ionized intermediate mass elements. Such lines are often referred to as 'coronal lines' since the ions, when produced by collisional ionization, reach maximum abundance at electron temperatures of approx. 10(exp 5) - 10(exp 6) K typical of the sun's upper atmosphere. However, optical and UV coronal lines are also observed in a wide variety of Galactic and extragalactic sources including the Galactic interstellar medium, nova shells, supernova remnants, galaxies and QSOs. Infrared coronal lines are providing a new window for observation of energetic emitting regions in heavily dust obscured sources such as infrared bright merging galaxies and Seyfert nuclei and new opportunities for model constraints on physical conditions in these sources. Unlike their UV and optical counterparts, infrared coronal lines can be primary coolants of collisionally ionized plasmas with 10(exp 4) less than T(sub e)(K) less than 10(exp 6) which produce little or no optical or shorter wavelength coronal line emission. In addition, they provide a means to probe heavily dust obscured emitting regions which are often inaccessible to optical or UV line studies. In this poster, we provide results from new model calculations to support upcoming Infrared Space Observatory (ISO) and current ground-based observing programs involving infrared coronal emission lines in AGN. We present a complete list of infrared (lambda greater than 1 micron) lines due to transitions within the ground configurations 2s(2)2p(k) and 3s(2)3p(k) (k = 1 to 5) or the first excited configurations 2s2p and 3s3p of highly ionized (x greater than or equal to 100 eV) astrophysically abundant (n(X)/n(H) greater than or equal to 10(exp -6)) elements. Included are approximately 74 lines in ions of O, Ne, Na, Mg, Al, Si, S, Ar, Ca, Fe, and Ni spanning a wavelength range of approximately 1 - 280 microns. We present new results from detailed balance calculations, new critical densities for collisional de-excitation, intrinsic photon rates, branching ratios, and excitation temperatures for the majority of the compiled transitions. The temperature and density parameter space for dominant cooling via infrared coronal lines is presented, and the relationship of infrared to optical coronal lines is discussed.

THE MAGELLANIC STREAM: BREAK-UP AND ACCRETION ONTO THE HOT GALACTIC CORONA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tepper-García, Thor; Bland-Hawthorn, Joss; Sutherland, Ralph S.

The Magellanic H i Stream (≈2 × 10{sup 9} M{sub ⊙} [d/55 kpc]{sup 2}) encircling the Galaxy at a distance d is arguably the most important tracer of what happens to gas accreting onto a disk galaxy. Recent observations reveal that the Stream’s mass is in fact dominated (3:1) by its ionized component. Here we revisit the origin of the mysterious Hα recombination emission observed along much of its length that is overly bright (∼150–200 mR) for the known Galactic ultraviolet (UV) background (≈20–40 mR [d/55 kpc]{sup −2}). In an earlier model, we proposed that a slow shock cascade wasmore » operating along the Stream due to its interaction with the extended Galactic hot corona. We find that for a smooth coronal density profile, this model can explain the bright Hα emission if the coronal density satisfies 2 × 10{sup −4} < (n/cm{sup −3}) < 4 × 10{sup −4} at d = 55 kpc. But in view of updated parameters for the Galactic halo and mounting evidence that most of the Stream must lie far beyond the Magellanic Clouds (d > 55 kpc), we revisit the shock cascade model in detail. At lower densities, the H i gas is broken down by the shock cascade but mostly mixes with the hot corona without significant recombination. At higher densities, the hot coronal mass (including the other baryonic components) exceeds the baryon budget of the Galaxy. If the Hα emission arises from the shock cascade, the upper limit on the smooth coronal density constrains the Stream’s mean distance to ≲75 kpc. If, as some models indicate, the Stream is even further out, either the shock cascade is operating in a regime where the corona is substantially mass-loaded with recent gas debris, or an entirely different ionization mechanism is responsible.« less

Exploration of the Characteristics of the Time Variable Component of the Coronal Heating Process

NASA Technical Reports Server (NTRS)

Wagner, William (Technical Monitor); Habbal, Shadia R.

2003-01-01

By coordinating coronal SOHO observations in white light, ultraviolet, extreme ultraviolet, with radio occultation measurements, and complementing these with modeling, two break-throughs were achieved from this funding: (1) The discovery that minor ions are accelerated much faster than protons in the fast solar wind, and (2) that the imprint of coronal density structures is carried outwards from the Sun into the solar wind. Three refereed papers and one invited review, published in the proceedings of the conference, resulted from this funding. A summary of each is given.

Coronal Magnetic Field Measurement from EUV Images Made by the Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Gopalswamy, Natchimuthuk; Nitta, Nariaki; Akiyama, Sachiko; Makela, Pertti; Yashiro, Seiji

2012-01-01

By measuring the geometrical properties of the coronal mass ejection (CME) flux rope and the leading shock observed on 2010 June 13 by the Solar Dynamics Observatory (SDO) mission's Atmospheric Imaging Assembly we determine the Alfven speed and the magnetic field strength in the inner corona at a heliocentric distance of approx. 1.4 Rs The basic measurements are the shock standoff distance (Delta R) ahead of the CME flux rope, the radius of curvature of the flux rope (R(sub c)), and the shock speed. We first derive the Alfvenic Mach number (M) using the relationship, Delta R/R(sub c) = 0.81[(gamma-1) M(exp 2) + 2] / [(gamma +1)(M2 - 1)], where gamma is the only parameter that needed to be assumed. For gamma = 4/3, the Mach number declined from 3.7 to 1.5 indicating shock weakening within the field of view of the imager. The shock formation coincided with the appearance of a type II radio burst at a frequency of approx. 300 MHz (harmonic component), providing an independent confirmation of the shock. The shock compression ratio derived from the radio dynamic spectrum was found to be consistent with that derived from the theory of fast-mode MHD shocks. From the measured shock speed and the derived Mach number, we found the Alfven speed to increase from approx 140 km/s to 460 km/s over the distance range 1.2-1.5 Rs. By deriving the upstream plasma density from the emission frequency of the associated type II radio burst, we determined the coronal magnetic field to be in the range 1.3-1.5 G. The derived magnetic field values are consistent with other estimates in a similar distance range. This work demonstrates that the EUV imagers, in the presence of radio dynamic spectra, can be used as coronal magnetometers

Interstellar C IV and Si IV column densities toward early-type stars

NASA Technical Reports Server (NTRS)

Bruhweiler, F. C.; Kondo, Y.; Mccluskey, G. E.

1980-01-01

Equivalent widths and deduced column densities of Si IV and C IV are examined for 18 early-type close binaries, and physical processes responsible for the origin of these ions in the interstellar medium are investigated. The available C IV/Si IV column density ratios typically lie within a narrow range from 0.8 to 4.5, and there is evidence that the column density of C IV is higher than that of N V along most lines of sight, suggesting that C IV is not formed in the same hot region as O VI. In addition, the existence of regions with a narrowly defined new temperature range around 50,000 deg K is indicated. The detection of the semitorrid gas of Bruhweiler, Kondo, and McCluskey (1978, 1979) is substantiated, and the relation of this gas to the observations of coronal gas in the galactic halo is discussed.

Anomalous Surge of the White-Light Corona at the Onset of the Declining Phase of Solar Cycle 24

NASA Astrophysics Data System (ADS)

Lamy, P.

2017-12-01

In late 2014, when the current solar cycle 24 was initiating its declining phase, the white-light corona as observed by the LASCO-C2 coronagraph underwent an unexpected surge that increased its global radiance by 60%, reaching a peak value comparable to those of the more active solar cycle 23. The daily variations point to a localized enhancement or bulge in the electron density that persisted during several months. Carrington maps of the radiance and of the HMI photospheric field allow connecting this bulge to the emergence of the large sunspot complex AR 12192 in October 2014, the largest since AR 6368 observed in November 1990. The resulting unusually large increase of the magnetic field and the distortion of the neutral sheet in a characteristic inverse S-shape caused the coronal plasma to be trapped along a similar pattern. Three-dimensional reconstruction of the electron density based on time-dependent solar rotational tomography supplemented by 2D inversion of the coronal radiance confirms the morphology of the bulge and reveals that its level was well above the standard models of a corona of the maximum type, by typically a factor of 3. A rather satisfactory agreement is found with the results of the thermodynamic MHD model produced by Predictive Sciences although discrepancies are noted. The specific configuration of the magnetic field that led to the coronal surge resulted from the interplay of various factors prevailing at the onset of the declining phase of the solar cycles which was particularly efficient in the case of solar cycle 24.

MHD Modelling of Coronal Loops: Injection of High-Speed Chromospheric Flows

NASA Technical Reports Server (NTRS)

Petralia, A.; Reale, F.; Orlando, S.; Klimchuk, J. A.

2014-01-01

Context. Observations reveal a correspondence between chromospheric type II spicules and bright upward-moving fronts in the corona observed in the extreme-ultraviolet (EUV) band. However, theoretical considerations suggest that these flows are probably not the main source of heating in coronal magnetic loops. Aims. We investigate the propagation of high-speed chromospheric flows into coronal magnetic flux tubes and the possible production of emission in the EUV band. Methods. We simulated the propagation of a dense 104 K chromospheric jet upward along a coronal loop by means of a 2D cylindrical MHD model that includes gravity, radiative losses, thermal conduction, and magnetic induction. The jet propagates in a complete atmosphere including the chromosphere and a tenuous cool (approximately 0.8 MK) corona, linked through a steep transition region. In our reference model, the jet initial speed is 70 km per second, its initial density is 10(exp 11) per cubic centimeter, and the ambient uniform magnetic field is 10 G. We also explored other values of jet speed and density in 1D and different magnetic field values in 2D, as well as the jet propagation in a hotter (approximately 1.5 MK) background loop. Results. While the initial speed of the jet does not allow it to reach the loop apex, a hot shock-front develops ahead of it and travels to the other extreme of the loop. The shock front compresses the coronal plasma and heats it to about 10(exp 6) K. As a result, a bright moving front becomes visible in the 171 Angstrom channel of the SDO/AIA mission. This result generally applies to all the other explored cases, except for the propagation in the hotter loop. Conclusions. For a cool, low-density initial coronal loop, the post-shock plasma ahead of upward chromospheric flows might explain at least part of the observed correspondence between type II spicules and EUV emission excess.

Acceleration of the Fast Solar Wind by Solitary Waves in Coronal Holes

NASA Technical Reports Server (NTRS)

Ofman, Leon

2001-01-01

The purpose of this investigation is to develop a new model for the acceleration of the fast solar wind by nonlinear. time-dependent multidimensional MHD simulations of waves in solar coronal holes. Preliminary computational studies indicate that nonlinear waves are generated in coronal holes by torsional Alfv\\'{e}n waves. These waves in addition to thermal conduction may contribute considerably to the accelerate the solar wind. Specific goals of this proposal are to investigate the generation of nonlinear solitary-like waves and their effect on solar wind acceleration by numerical 2.5D MHD simulation of coronal holes with a broad range of plasma and wave parameters; to study the effect of random disturbances at the base of a solar coronal hole on the fast solar wind acceleration with a more advanced 2.5D MHD model and to compare the results with the available observations; to extend the study to a full 3D MHD simulation of fast solar wind acceleration with a more realistic model of a coronal hole and solar boundary conditions. The ultimate goal of the three year study is to model the, fast solar wind in a coronal hole, based on realistic boundary conditions in a coronal hole near the Sun, and the coronal hole structure (i.e., density, temperature. and magnetic field geometry,) that will become available from the recently launched SOHO spacecraft.

Acceleration of the Fast Solar Wind by Solitary Waves in Coronal Holes

NASA Technical Reports Server (NTRS)

Ofman, Leon

2000-01-01

The purpose of this investigation is to develop a new model for the acceleration of the fast solar wind by nonlinear, time-dependent multidimensional MHD simulations of waves in solar coronal holes. Preliminary computational studies indicate that solitary-like waves are generated in coronal holes nonlinearly by torsional Alfven waves. These waves in addition to thermal conduction may contribute considerably to the accelerate the solar wind. Specific goals of this proposal are to investigate the generation of nonlinear solitary-like waves and their effect on solar wind acceleration by numerical 2.5D MHD simulation of coronal holes with a broad range of plasma and wave parameters; to study the effect of random disturbances at the base of a solar coronal hole on the fast solar wind acceleration with a more advanced 2.5D MHD model and to compare the results with the available observations; to extend the study to a full 3D MHD simulation of fast solar wind acceleration with a more realistic model of a coronal hole and solar boundary conditions. The ultimate goal of the three year study is to model the fast solar wind in a coronal hole, based on realistic boundary conditions in a coronal hole near the Sun, and the coronal hole structure (i.e., density, temperature, and magnetic field geometry) that will become available from the recently launched SOHO spacecraft.

Radiological factors affecting post-operative global coronal balance in Lenke 5 C scoliosis.

PubMed

Shetty, Ajoy Prasad; Suresh, Subramani; Aiyer, Siddharth N; Kanna, Rishi; Rajasekaran, Shanmuganathan

2017-12-01

Lenke 5 C curves are frequently associated with clinically and radiological coronal imbalance. Appropriate selection of proximal and distal levels of fusion is essential to ensure good coronal balance (CB). We aimed to evaluate radiological factors associated with (I) global CB in the early post-operative period; (II) late decompensation of CB; and (III) favourable spontaneous correction of CB on long term follow up. Twenty-three Lenke type 5C scoliosis cases treated with selective posterior lumbar instrumentation were retrospectively evaluated. Pre-operative, early post-operative and late post-operative (>2 years) whole length radiographs were analysed. Cobb's angle, lumbar lordosis, coronal imbalance, lower instrumented vertebra (LIV) tilt and translation and upper instrumented vertebra (UIV) tilt and translation were measured. The proximal and distal fusion levels were noted and correlated with post-operative CB. There were 21 females and 2 males with a mean follow up of 36 months. The mean pre-operative cobb angle was 55°±13.26°, which corrected to 14.7°±8.84° and was maintained on follow up. Eight patients had early post-operative coronal imbalance with spontaneous resolution seen in six cases on long term follow-up. At final follow-up, four cases had coronal imbalance (persistent imbalance since early post-operative period =2; late decompensation =2). In cases with early imbalance 5/8 cases had a pre-operative LIV tilt of ≥25°. All four patients with coronal imbalance at final follow-up had pre-operative LIV tilt ≥25°. Radiographic parameters which correlated with post-operative coronal imbalance were pre-operative LIV tilt (r=0.64, P=0.001), pre-operative LIV translation (r=0.696, P<0.001), pre-operative UIV translation (r=0.44, P=0.030), post-operative LIV tilt (r=0.804, P<0.001), and post-operative UIV tilt (r=0.62, P=0.001). In Lenke 5C scoliosis, a pre-operative LIV tilt ≥25° significantly correlates with post-operative global coronal imbalance. Increasing UIV tilt may be a factor that accounts for improvement of CB in late follow-up period.

Radiological factors affecting post-operative global coronal balance in Lenke 5 C scoliosis

PubMed Central

Suresh, Subramani; Aiyer, Siddharth N.; Kanna, Rishi; Rajasekaran, Shanmuganathan

2017-01-01

Background Lenke 5 C curves are frequently associated with clinically and radiological coronal imbalance. Appropriate selection of proximal and distal levels of fusion is essential to ensure good coronal balance (CB). We aimed to evaluate radiological factors associated with (I) global CB in the early post-operative period; (II) late decompensation of CB; and (III) favourable spontaneous correction of CB on long term follow up. Methods Twenty-three Lenke type 5C scoliosis cases treated with selective posterior lumbar instrumentation were retrospectively evaluated. Pre-operative, early post-operative and late post-operative (>2 years) whole length radiographs were analysed. Cobb’s angle, lumbar lordosis, coronal imbalance, lower instrumented vertebra (LIV) tilt and translation and upper instrumented vertebra (UIV) tilt and translation were measured. The proximal and distal fusion levels were noted and correlated with post-operative CB. Results There were 21 females and 2 males with a mean follow up of 36 months. The mean pre-operative cobb angle was 55°±13.26°, which corrected to 14.7°±8.84° and was maintained on follow up. Eight patients had early post-operative coronal imbalance with spontaneous resolution seen in six cases on long term follow-up. At final follow-up, four cases had coronal imbalance (persistent imbalance since early post-operative period =2; late decompensation =2). In cases with early imbalance 5/8 cases had a pre-operative LIV tilt of ≥25°. All four patients with coronal imbalance at final follow-up had pre-operative LIV tilt ≥25°. Radiographic parameters which correlated with post-operative coronal imbalance were pre-operative LIV tilt (r=0.64, P=0.001), pre-operative LIV translation (r=0.696, P<0.001), pre-operative UIV translation (r=0.44, P=0.030), post-operative LIV tilt (r=0.804, P<0.001), and post-operative UIV tilt (r=0.62, P=0.001). Conclusions In Lenke 5C scoliosis, a pre-operative LIV tilt ≥25° significantly correlates with post-operative global coronal imbalance. Increasing UIV tilt may be a factor that accounts for improvement of CB in late follow-up period. PMID:29354729

Radio range measurements of coronal electron densities at 13 and 3.6 centimeter wavelengths during the 1988 solar conjunction of Voyager 2

NASA Technical Reports Server (NTRS)

Krisher, T. P.; Anderson, J. D.; Morabito, D. D.; Asmar, S. W.; Borutzki, S. E.; Delitsky, M. L.; Densmore, A. C.; Eshe, P. M.; Lewis, G. D.; Maurer, M. J.

1991-01-01

Radio range measurements of total solar plasma delay obtained during the solar conjunction of the Voyager 2 spacecraft in December 1988, which occurred near solar maximum activity in the 11 yr cycle are reported. The radio range measurements were generated by the Deep Space Network at two wavelengths on the downlink from the spacecraft: 3.6 and 13 cm. A direct measurement of the integrated electron density along the ray path between the earth stations and the spacecraft was obtained by differencing the range at the two wavelengths. Coronal electron density profiles have been derived during ingress and egress of the ray path, which approached the sun to within 5 solar radii. At 10 solar radii, the derived density profiles yield 34079 + or - 611/cu cm on ingress and 49688 + or - 983/cu cm on egress. These density levels are significantly higher than observed near previous solar maxima.

Effect of higher implant density on curve correction in dystrophic thoracic scoliosis secondary to neurofibromatosis Type 1.

PubMed

Li, Yang; Yuan, Xinxin; Sha, Shifu; Liu, Zhen; Zhu, Weiguo; Qiu, Yong; Wang, Bin; Yu, Yang; Zhu, Zezhang

2017-10-01

OBJECTIVE The aim of this study was to investigate how implant density affects radiographic results and clinical outcomes in patients with dystrophic scoliosis secondary to neurofibromatosis Type 1 (NF1). METHODS A total of 41 patients with dystrophic scoliosis secondary to NF1 who underwent 1-stage posterior correction between June 2011 and December 2013 were included. General information about patients was recorded, as were preoperative and postoperative scores from Scoliosis Research Society (SRS)-22 questionnaires. Pearson correlation analysis was used to analyze the associations among implant density, coronal Cobb angle correction rate and correction loss at last follow-up, change of sagittal curve, and apical vertebral translation. Patients were then divided into 2 groups: those with low-density and those with high-density implants. Independent-sample t-tests were used to compare demographic data, radiographic findings, and clinical outcomes before surgery and at last follow-up between the groups. RESULTS Significant correlations were found between the implant density and the coronal correction rate of the main curve (r = 0.505, p < 0.01) and the coronal correction loss at final follow-up (r = -0.379, p = 0.015). There was no significant correlation between implant density and change of sagittal profile (p = 0.662) or apical vertebral translation (p = 0.062). The SRS-22 scores improved in the appearance, activity, and mental health domains within both groups, but there was no difference between the groups in any of the SRS-22 domains at final follow-up (p > 0.05 for all). CONCLUSIONS Although no significant differences between the high- and low-density groups were found in any of the SRS-22 domains at final follow-up, higher implant density was correlated with superior coronal correction and less postoperative correction loss in patients with dystrophic NF1-associated scoliosis.

Investigation of the Electron Density Variation During the 21 August 2017 Solar Eclipse

NASA Astrophysics Data System (ADS)

Reinisch, B. W.; Dandenault, P. B.; Galkin, I. A.; Hamel, R.; Richards, P. G.

2018-02-01

This paper presents a comparison of modeled and measured electron densities for the 21 August 2017 solar eclipse across the USA. The location of the instrument was (43.81°N, 247.32°E) where the maximum obscuration of 99.6% occurred at 17.53 hr UT on 21 August. The solar apparent time was 9.96 hr, and the duration of the eclipse was 2.7 hr. It was found that if it is assumed that there are no chromosphere emissions at totality, 30% coronal emission remaining at totality gave the best fit to the electron density variation at 150 km. The 30% coronal emission estimate has uncertainties associated with respect to uncertainties in the solar spectrum, the measured electron density, and the amount of chromosphere emissions remaining at totality. The agreement between the modeled and measured electron densities is excellent at 150 km with the assumed 30% coronal emission at totality. At other altitudes, the agreement is very good, but the altitude profile would be improved if the model peak electron density (NmF2) decayed more slowly to better match the data. The minimum NmF2 in the model occurs 10 min after totality when it decreases to 0.55 from its noneclipse value. The minimum of the NmF2 data occurs between 6 and 10 min after totality but is 15% larger. The total electron content decreases to 0.65 of its preeclipse value. These relative changes agree well with those predicted by others prior to the eclipse.

Impulsively Generated Wave Trains in Coronal Structures. II. Effects of Transverse Structuring on Sausage Waves in Pressurelesss Slabs

NASA Astrophysics Data System (ADS)

Li, Bo; Guo, Ming-Zhe; Yu, Hui; Chen, Shao-Xia

2018-03-01

Impulsively generated sausage wave trains in coronal structures are important for interpreting a substantial number of observations of quasi-periodic signals with quasi-periods of order seconds. We have previously shown that the Morlet spectra of these wave trains in coronal tubes depend crucially on the dispersive properties of trapped sausage waves, the existence of cutoff axial wavenumbers, and the monotonicity of the dependence of the axial group speed on the axial wavenumber in particular. This study examines the difference a slab geometry may introduce, for which purpose we conduct a comprehensive eigenmode analysis, both analytically and numerically, on trapped sausage modes in coronal slabs with a considerable number of density profiles. For the profile descriptions examined, coronal slabs can trap sausage waves with longer axial wavelengths, and the group speed approaches the internal Alfvén speed more rapidly at large wavenumbers in the cylindrical case. However, common to both geometries, cutoff wavenumbers exist only when the density profile falls sufficiently rapidly at distances far from coronal structures. Likewise, the monotonicity of the group speed curves depends critically on the profile steepness right at the structure axis. Furthermore, the Morlet spectra of the wave trains are shaped by the group speed curves for coronal slabs and tubes alike. Consequently, we conclude that these spectra have the potential for inferring the subresolution density structuring inside coronal structures, although their detection requires an instrumental cadence of better than ∼1 s.

Modeling a simple coronal streamer during whole sun month

NASA Technical Reports Server (NTRS)

Gibson, S. E.; Bagenal, F.; Biesecker, D.; Guhathakurta, M.; Hoeksema, J. T.; Thompson, B. J.

1997-01-01

The solar minimum streamer structure observed during the whole sun month was modeled. The Van de Hulst inversion was used in order to determine the coronal electron density profiles and scale-height temperature profiles. The axisymmetric magnetostatic model of Gibson, Bagenal and Low was also used. The density, temperature, and magnetic field distribution were quantified using both coronal white light data and photospheric magnetic field data from the Wilcox Solar Observatory. The densities and temperatures obtained by the Van de Hulst and magnetostatic models are compared to the magnetic field predicted by the magnetostatic model to a potential field extrapolated from the photosphere.

X-Raying the Coronae of HD 155555

NASA Technical Reports Server (NTRS)

Lalitha, S.; Singh, K.P.; Drake, S. A.; Kashyap, V.

2015-01-01

We present an analysis of the high-resolution Chandra observation of the multiple system, HD 155555 (an RS CVn type binary system, HD 155555 AB, and its spatially resolved low-mass companion HD 155555 C). This is an intriguing system which shows properties of both an active pre-main sequence star and a synchronised (main sequence) binary. We obtain the emission measure distribution, temperature structures, plasma densities, and abundances of this system and compare them with the coronal properties of other young/active stars. HD 155555 AB and HD 155555 C produce copious X-ray emission with log L(sub x) of 30.54 and 29.30, respectively, in the 0.3-6.0 kiloelectronvolt energy band. The light curves of individual stars show variability on timescales of few minutes to hours. We analyse the dispersed spectra and reconstruct the emission measure distribution using spectral line analysis. The resulting elemental abundances exhibit inverse first ionisation potential effect in both cases. An analysis of He-like triplets yields a range of coronal electron densities 1010 - 1013 per cubic centimeter. Since HD 155555 AB is classified both as an RS CVn and a PMS star, we compare our results with those of other slightly older active main-sequence stars and T Tauri stars, which indicates that the coronal properties of HD 155555 AB closely resemble that of an older RS CVn binary rather than a younger PMS star. Our results also suggests that the properties of HD 155555 C is very similar to those of other active M dwarfs.

RS CVn binaries: Testing the solar-stellar dynamo connection

NASA Technical Reports Server (NTRS)

Dempsey, R.

1995-01-01

We have used the Extreme Ultraviolet Explorer satellite to study the coronal emission from the EUV-bright RS CVn binaries Sigma2 CrB, observed February 10-21, 1994, and II Peg, observed October 1-5, 1993. We present time-resolved and integrated EUV short-, medium-, and long-wavelength spectra for these binaries. Sigma2 CrB shows significant first-order emission features in the long-wavelength region. The coronal emission distributions and electron densities are estimated for those active coronae dominated by high temperature plasma.

Magnetohydrodynamic Simulation of a Streamer Beside a Realistic Coronal Hole

NASA Technical Reports Server (NTRS)

Suess, S. T.; Wu, S. T.; Wang, A. H.; Poletto, G.

1994-01-01

Existing models of coronal streamers establish their credibility and act as the initial state for transients. The models have produced satisfactory streamer simulations, but unsatisfactory coronal hole simulations. This is a consequence of the character of the models and the boundary conditions. The models all have higher densities in the magnetically open regions than occur in coronal holes (Noci, et al., 1993).

The solar flare iron line to continuum ratio and the coronal abundances of iron and helium

NASA Technical Reports Server (NTRS)

Mckenzie, D. L.

1975-01-01

Narrow band Ross filter measurements of the Fe 25 line flux around 0.185 nm and simultaneous broadband measurements during a solar flare were used to determine the relationship between the solar coronal abundances of iron and helium. The Fe 25 ion population was also determined as a function of time. The proportional counter and the Ross filter on OSO-7 were utilized. The data were analyzed under the separate assumptions that (1) the electron density was high enough that a single temperature could characterize the continuum spectrum and the ionization equilibrium, and that (2) the electron density was low so that the ion populations trailed the electron temperature in time. It was found that the density was at least 5x10 to the 9th power, and that the high density assumption was valid. It was also found that the iron abundance is 0.000011 for a helium abundance of 0.2, relative to hydrogen.

Turbulent Density Fluctuations and Proton Heating Rate in the Solar Wind from 9-20 R ⊙

NASA Astrophysics Data System (ADS)

Sasikumar Raja, K.; Subramanian, Prasad; Ramesh, R.; Vourlidas, Angelos; Ingale, Madhusudan

2017-12-01

We obtain scatter-broadened images of the Crab Nebula at 80 MHz as it transits through the inner solar wind in 2017 and 2016 June. These images are anisotropic, with the major axis oriented perpendicular to the radially outward coronal magnetic field. Using these data, we deduce that the density modulation index (δ {N}e/{N}e) caused by turbulent density fluctuations in the solar wind ranges from 1.9× {10}-3 to 7.7× {10}-3 between 9 and 20 R ⊙. We also find that the heating rate of solar wind protons at these distances ranges from 2.2× {10}-13 to 1.0× {10}-11 {erg} {{cm}}-3 {{{s}}}-1. On two occasions, the line of sight intercepted a coronal streamer. We find that the presence of the streamer approximately doubles the thickness of the scattering screen.

Core and Wing Densities of Asymmetric Coronal Spectral Profiles: Implications for the Mass Supply of the Solar Corona

NASA Astrophysics Data System (ADS)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R.

2014-02-01

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding ≈50 km s-1. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe XIV lines at 264.78 and 274.20 Å is used to determine wing and core densities. We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe XIV lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.

Core and Wing Densities of Asymmetric Coronal Spectral Profiles: Implications for the Mass Supply of the Solar Corona

NASA Technical Reports Server (NTRS)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R.

2014-01-01

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding approximately equal to 50 km per sec. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe(sub XIV) lines at 264.78 and 274.20 Angstroms is used to determine wing and core densities.We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe(sub XIV) lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.

Brightening and Darkening of the Extended Solar Corona during the Superflares of September 2017

NASA Astrophysics Data System (ADS)

Goryaev, Farid F.; Slemzin, Vladimir A.; Rodkin, Denis G.; D’Huys, Elke; Podladchikova, O.; West, Matthew J.

2018-04-01

On 2017 September 6 and 10, the strongest X9.3 and X8.2 flares of the decade occurred in the active region NOAA Active Region 12673. During these flares, the Sun Watcher with Active Pixels and Image Processing (SWAP) telescope on board the Project for Onboard Autonomy 2 (PROBA2) satellite registered the unusual alternate brightening and darkening of the western corona at the heliocentric distances ≈1.2–1.7 R ⊙. The X9.3 flare on 2017 September 6 was accompanied by coronal brightening up to 30%–45% at distances ≈1.35–1.7 R ⊙. Numerical simulations showed that this brightening might be produced by resonant scattering of the flare radiation by the Fe IX–Fe XI ions in the coronal plasma at the temperature T ∼ 0.8–1 MK, and the densities seriously reduced in comparison with the typical values for the quiet background corona probably moving outward with velocities of 30–40 km s‑1. At the maximum of the flare and one hour later, two coronal mass ejections (CMEs) originated, which dimmed the coronal emission in the SWAP 174 Å passband above the western limb by 20%–30%. The X8.2 flare on September 10 was accompanied by a CME, which rose up and progressively dimmed the western part of the corona up to 60%. An hour later the darkening, produced by a global rearrangement of the magnetic field structure and an evacuation of a significant part of the coronal plasma, extended over the complete western limb. A differential emission measure (DEM) analysis showed a decrease in the electron density of the background plasma with T ∼ 1–2 MK at distances 1.24–1.33 R ⊙ by 2–3.5 times after the CME. At the same time, an additional DEM peak at T ≈ 0.8 MK appeared, which may be associated with an additional emission in the SWAP passband produced by the flare radiation resonantly scattered by the coronal plasma.

Very large array faraday rotation studies of the coronal plasma

NASA Astrophysics Data System (ADS)

Kooi, Jason Earl

Knowledge of the coronal magnetic field is crucial for understanding (1) the heating mechanism(s) of the solar corona, (2) the acceleration of the fast solar wind, and (3) the structure and dynamics of coronal mass ejections (CMEs). Observation of Faraday rotation (FR) is one of the best remote-sensing techniques for determining plasma properties in the corona and can provide information on the plasma structure of a CME shortly after launch, shedding light on the initiation process. I used the Karl G. Jansky Very Large Array (VLA) to make sensitive Faraday rotation measurements to investigate the general plasma structure of the corona, properties of coronal plasma inhomogeneities and waves, and transients associated with coronal mass ejections. To enhance my measurements of FR transients, I also developed an algorithm in the Common Astronomy Software Applications (CASA) package to mitigate ionospheric Faraday rotation. In August, 2011, I made FR observations at 5.0 and 6.1 GHz of the radio galaxy 3C 228 through the solar corona at heliocentric distances of 4.6-5.0 solar radii using the VLA. Observations at 5.0 GHz permit measurements deeper in the corona than previous VLA observations at 1.4 and 1.7 GHz. These FR observations provided unique information on the magnetic field in this region of the corona. My data on 3C 228 provide two lines of sight (separated by 46 arcseconds, 33,000 km in the corona). I detected three periods during which there appeared to be a difference in the Faraday rotation measure between these two closely spaced lines of sight, which I used to estimate coronal currents; these values (ranging from 2.6 to 4.1 GA) are several orders of magnitude below that which is necessary for significant coronal heating (assuming the Spitzer resistivity). I also used the data to determine upper limits (3.3 and 6.4 rad/m2 along the two lines of sight) on FR fluctuations caused by coronal waves. These upper limits are comparable to and, thus, not inconsistent with the theoretical models for Alfven wave heating of the corona by Hollweg et al. (2010). To support the needs of the low frequency radioastronomical community as well as my own research of coronal FR transients, I developed a new calibration algorithm for CASA that uses GPS-based global ionosphere maps of the Total Electron Content (TEC) to mitigate ionospheric Faraday rotation. The Earth's ionosphere introduces direction- and time-dependent effects over a range of physical and temporal scales and so is a major source for unmodeled phase offsets for low frequency radioastronomical observations. It has become common practice to use global ionospheric models derived from the Global Positioning System (GPS) to provide a means of externally calibrating low frequency data. However, CASA, which was developed to meet the data post-processing needs of next generation telescopes such as the VLA and the Atacama Large Millimeter/submillimeter Array (ALMA), did not have the capability to make ionospheric corrections before I implemented this calibration algorithm. I investigated several data centers as potential sources for global ionospheric models and chose the International Global Navigation Satellite System Service data product because data from other sources are generally too sparse to use without additional interpolation schemes. I employed these ionospheric corrections in reducing VLA observations made in August, 2012, at 1-2 GHz of a "constellation'' of radio sources through the solar corona at heliocentric distances that ranged from 5-15 solar radii. Of the nine sources observed, three were occulted by CMEs: 0842+1835, 0900+1832, and 0843+1547. In addition to my radioastronomical observations, which represent one of the first active hunts for CME Faraday rotation since Bird et al. (1985) and the first active hunt using the VLA, I obtained white-light coronagraph images from the LASCO/C3 instrument aboard SOHO to determine the Thomson scattering brightness, BT. BT is proportional to the electron plasma density and provides a means to independently estimate the plasma density and determine its contribution to the observed Faraday rotation. A constant density force-free flux rope embedded in the background corona was used to model the effects of the CMEs on BT and FR. In the case of 0842+1835, the flux rope model underestimated the peak value in BT and did not reproduce the decreasing BT inside the inner cavity region of the CME; however, there was satisfactory agreement between the model and the observed FR. The single flux rope model successfully reproduces both the observed BT and FR profiles for 0900+1832. 0843+1547 was occulted by two CMEs. Therefore, I modeled observations of 0843+1547 using two flux ropes embedded in the background corona. The two flux rope model successfully reproduces both BT and FR profiles for 0843+1547 and, in particular, the two flux rope model successfully replicates the appropriate slope in FR before and after occultation by the second CME and predicts the observed change in sign to FR > 0 at the end of the observing session. I briefly discuss the plasma densities (6-22 x 10 3 cm-3) and axial magnetic field strengths (2-12 mG) inferred from my models and compare them to the modeling work of Liu et al. (2007) and Jensen et al. (2008), as well as previous CME FR observations by Bird et al. (1985).

Radio Studies of Coronal Holes.

DTIC Science & Technology

1981-03-01

Withbroe (1978) has pointed out, "The transport of energy by thermal conduction into the transition zone is a primary coronal cooling mechanism." Thus, the...temperature and particle density gradients in the transition zone are of critical importance in understanding the energy balance of a coronal hole. The...coronal hole has been provided by Konp and Orrall (1977), but a quantitative understanding requires a detailed knowledge of the energy balance in the

INFERRING THE CORONAL DENSITY IRREGULARITY FROM EUV SPECTRA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hahn, M.; Savin, D. W., E-mail: mhahn@astro.columbia.edu

2016-09-20

Understanding the density structure of the solar corona is important for modeling both coronal heating and the solar wind. Direct measurements are difficult because of line-of-sight integration and possible unresolved structures. We present a new method for quantifying such structures using density-sensitive extreme ultraviolet line intensities to derive a density irregularity parameter, a relative measure of the amount of structure along the line of sight. We also present a simple model to relate the inferred irregularities to physical quantities, such as the filling factor and density contrast. For quiet-Sun regions and interplume regions of coronal holes, we find a densitymore » contrast of at least a factor of 3–10 and corresponding filling factors of about 10%–20%. Our results are in rough agreement with other estimates of the density structures in these regions. The irregularity diagnostic provides a useful relative measure of unresolved structure in various regions of the corona.« less

Can Thermal Nonequilibrium Explain Coronal Loops?

NASA Technical Reports Server (NTRS)

Klimchuk, James A.; Karpen, Judy T.; Antiochos, Spiro K.

2010-01-01

Any successful model of coronal loops must explain a number of observed properties. For warm (approx. 1 MK) loops, these include: 1. excess density, 2. flat temperature profile, 3. super-hydrostatic scale height, 4. unstructured intensity profile, and 5. 1000-5000 s lifetime. We examine whether thermal nonequilibrium can reproduce the observations by performing hydrodynamic simulations based on steady coronal heating that decreases exponentially with height. We consider both monolithic and multi-stranded loops. The simulations successfully reproduce certain aspects of the observations, including the excess density, but each of them fails in at least one critical way. -Xonolithic models have far too much intensity structure, while multi-strand models are either too structured or too long-lived. Storms of nanoflares remain the only viable explanation for warm loops that has been proposed so far. Our results appear to rule out the widespread existence of heating that is both highly concentrated low in the corona and steady or quasi-steady (slowly varying or impulsive with a rapid cadence). Active regions would have a very different appearance if the dominant heating mechanism had these properties. Thermal nonequilibrium may nonetheless play an important role in prominences and catastrophic cooling e(veen.gts..,coronal rain) that occupy a small fraction of the coronal volume. However, apparent inconsistencies between the models and observations of cooling events have yet to be understood.

Forward Modeling of a Coronal Cavity

NASA Technical Reports Server (NTRS)

Kucera, T. A.; Gibson, S. E.; Schmit, D. J.

2011-01-01

We apply a forward model of emission from a coronal cavity in an effort to determine the temperature and density distribution in the cavity. Coronal cavities are long, low-density structures located over filament neutral lines and are often seen as dark elliptical features at the solar limb in white light, EUV and X-rays. When these structures erupt they form the cavity portions of CMEs The model consists of a coronal streamer model with a tunnel-like cavity with elliptical cross-section and a Gaussian variation of height along the tunnel length. Temperature and density can be varied as a function of altitude both in the cavity and streamer. We apply this model to a cavity observed in Aug. 2007 by a wide array of instruments including Hinode/EIS, STEREO/EUVI and SOHO/EIT. Studies such as these will ultimately help us understand the the original structures which erupt to become CMEs and ICMES, one of the prime Solar Orbiter objectives.

A two-dimensional MHD global coronal model - Steady-state streamers

NASA Technical Reports Server (NTRS)

Wang, A.-H.; Wu, S. T.; Suess, S. T.; Poletto, G.

1992-01-01

A 2D, time-dependent, numerical, MHD model for the simulation of coronal streamers from the solar surface to 15 solar is presented. Three examples are given; for dipole, quadrupole and hexapole (Legendre polynomials P1, P2, and P3) initial field topologies. The computed properties are density, temperature, velocity, and magnetic field. The calculation is set up as an initial-boundary value problem wherein a relaxation in time produces the steady state solution. In addition to the properties of the solutions, their accuracy is discussed. Besides solutions for dipole, quadrupole, and hexapole geometries, the model use of realistic values for the density and Alfven speed while still meeting the requirement that the flow speed be super-Alfvenic at the outer boundary by extending the outer boundary to 15 solar radii.

Hi-C and AIA observations of transverse magnetohydrodynamic waves in active regions

NASA Astrophysics Data System (ADS)

Morton, R. J.; McLaughlin, J. A.

2013-05-01

The recent launch of the High resolution Coronal imager (Hi-C) provided a unique opportunity of studying the EUV corona with unprecedented spatial resolution. We utilize these observations to investigate the properties of low-frequency (50-200 s) active region transverse waves, whose omnipresence had been suggested previously. The five-fold improvement in spatial resolution over SDO/AIA reveals coronal loops with widths 150-310 km and that these loops support transverse waves with displacement amplitudes <50 km. However, the results suggest that wave activity in the coronal loops is of low energy, with typical velocity amplitudes <3 km s-1. An extended time-series of SDO data suggests that low-energy wave behaviour is typical of the coronal structures both before and after the Hi-C observations. Appendix A and five movies associated to Figs. A.2-A.6 are available in electronic form at http://www.aanda.org

Coronal gas in the galaxy. II. A statistical analysis of O VI absorptions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jenkins, E.B.

Results from the survey of interstellar O VI by Jenkins and by Jenkins and Meloy are analyzed to synthesize a global description of the properties of the coronal gas. Tests for correlations of column densities or velocities with properties of the target stars showed no evidence for a circumstellar origin for the absorption lines. An overall average density n (O VI) =2.8 x 10/sup -8/ cm/sup -3/ was found in the galactic plane, with a decrease which approximately follows exp (-z/300 pc) away from the plane.Fluctuations in column densities over various lines of sight suggest that existence of six hotmore » gas regions kpc/sup -/1, randomly distributed in space, each with an O VI column density of about 10/sup 13/ cm/sup -2/. These regions account for an average density n (O VI) =2.1 x 10/sup -8/ cm/sup -3/; the remaining 7 x 10/sup -9/ cm/sup -3/ is produced by more sparsely distributed but thicker parcels of hot gas which are seen toward 10% of the stars. The statistics of radial velocity centroids and widths support the interpretation of distinct domains; each region has an internal velocity dispersion consistent with a Doppler broadening of a plasma at T> or approx. =2 x 10/sup 5/ K (near the characteristic temperature for a maximum concentration of O VI in collisional equilibrium), while the regions themselves move about with a dispersion of radial velocities equal to 26 km s/sup -1/. Systematic motions of gas away from the galactic plane could not be seen, however.Excursions from the normal O VI per unit distance have no perceptible anicorrelation with deviations in reddening by cool interstellar coulds: a fact which suggests that the average filling factor of O VI gas is less than 20% if coronal gas really displaces the cooler material and does not have large variations in density and temperature.« less

Evaluation of implants coated with recombinant human bone morphogenetic protein-2 and vacuum-dried using the critical-size supraalveolar peri-implant defect model in dogs.

PubMed

Decker, John F; Lee, Jaebum; Cortella, Carlo Alberto; Polimeni, Giuseppe; Rohrer, Michael D; Wozney, John M; Hall, Jan; Susin, Cristiano; Wikesjö, Ulf M E

2010-12-01

Endosseous implants coated with recombinant human bone morphogenetic protein-2 (rhBMP-2) in a laboratory bench setting and air-dried induce relevant bone formation but also resident bone remodeling. Thus, the objective of this study is to evaluate the effect of implants fully or partially coated with rhBMP-2 and vacuum-dried using an industrial process on local bone formation and resident bone remodeling. Twelve male adult Hound Labrador mongrel dogs were used. Critical-size, supraalveolar, peri-implant defects received titanium porous oxide surface implants coated in their most coronal aspect with rhBMP-2 (coronal-load, six animals), or by immersion of the entire implant in a rhBMP-2 solution (soak-load, six animals) for a total of 30 μg rhBMP-2 per implant. All implants were vacuum-dried. The animals were sacrificed at 8 weeks for histometric evaluation. Clinical healing was unremarkable. Bone formation was not significantly affected by the rhBMP-2 application protocol. New bone height and area averaged (± SE) 3.2 ± 0.5 versus 3.6 ± 0.3 mm, and 2.3 ± 0.5 versus 2.6 ± 0.8 mm(2) for coronal-load and soak-load implants, respectively (P >0.05). The corresponding bone density and bone-implant contact registrations averaged 46.7% ± 5.8% versus 31.6% ± 4.4%, and 28% ± 5.6% versus 36.9% ± 3.4% (P >0.05). In contrast, resident bone remodeling was significantly influenced by the rhBMP-2 application protocol. Peri-implant bone density averaged 72.2% ± 2.1% for coronal-load versus 60.6% ± 4.7% for soak-load implants (P <0.05); the corresponding bone-implant contact averaged 70.7% ± 6.1% versus 47.2% ± 6.0% (P <0.05). Local application of rhBMP-2 and vacuum-drying using industrial process seems to be a viable technology to manufacture implants that support local bone formation and osseointegration. Coronal-load implants obviate resident bone remodeling without compromising local bone formation.

Which Bow Shock Theory, Gasdynamic or Magnetohydrodynamic, Better Explains CME Stand-off Distance Ratios from LASCO-C2 Observations ?

NASA Astrophysics Data System (ADS)

Lee, Jae-Ok; Moon, Y.-J.; Lee, Jin-Yi; Kim, R.-S.; Cho, K.-S.

2017-03-01

It is generally believed that fast coronal mass ejections (CMEs) can generate their associated shocks, which are characterized by faint structures ahead of CMEs in white-light coronagraph images. In this study, we examine whether the observational stand-off distance ratio, defined as the CME stand-off distance divided by its radius, can be explained by bow shock theories. Of 535 SOHO/LASCO CMEs (from 1996 to 2015) with speeds greater than 1000 km s-1 and angular widths wider than 60°, we select 18 limb CMEs with the following conditions: (1) their Alfvénic Mach numbers are greater than one under Mann’s magnetic field and Saito’s density distributions; and (2) the shock structures ahead of the CMEs are well identified. We determine observational CME stand-off distance ratios by using brightness profiles from LASCO-C2 observations. We compare our estimates with theoretical stand-off distance ratios from gasdynamic (GD) and magnetohydrodynamic (MHD) theories. The main results are as follows. Under the GD theory, 39% (7/18) of the CMEs are explained in the acceptable ranges of adiabatic gamma (γ) and CME geometry. Under the MHD theory, all the events are well explained when we consider quasi-parallel MHD shocks with γ = 5/3. When we use polarized brightness (pB) measurements for coronal density distributions, we also find similar results: 8% (1/12) under GD theory and 100% (12/12) under MHD theory. Our results demonstrate that the bow shock relationships based on MHD theory are more suitable than those based on GD theory for analyzing CME-driven shock signatures.

Which Bow Shock Theory, Gasdynamic or Magnetohydrodynamic, Better Explains CME Stand-off Distance Ratios from LASCO-C2 Observations ?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jae-Ok; Moon, Y.-J.; Lee, Jin-Yi

It is generally believed that fast coronal mass ejections (CMEs) can generate their associated shocks, which are characterized by faint structures ahead of CMEs in white-light coronagraph images. In this study, we examine whether the observational stand-off distance ratio, defined as the CME stand-off distance divided by its radius, can be explained by bow shock theories. Of 535 SOHO /LASCO CMEs (from 1996 to 2015) with speeds greater than 1000 km s{sup −1} and angular widths wider than 60°, we select 18 limb CMEs with the following conditions: (1) their Alfvénic Mach numbers are greater than one under Mann’s magneticmore » field and Saito’s density distributions; and (2) the shock structures ahead of the CMEs are well identified. We determine observational CME stand-off distance ratios by using brightness profiles from LASCO-C2 observations. We compare our estimates with theoretical stand-off distance ratios from gasdynamic (GD) and magnetohydrodynamic (MHD) theories. The main results are as follows. Under the GD theory, 39% (7/18) of the CMEs are explained in the acceptable ranges of adiabatic gamma ( γ ) and CME geometry. Under the MHD theory, all the events are well explained when we consider quasi-parallel MHD shocks with γ = 5/3. When we use polarized brightness (pB) measurements for coronal density distributions, we also find similar results: 8% (1/12) under GD theory and 100% (12/12) under MHD theory. Our results demonstrate that the bow shock relationships based on MHD theory are more suitable than those based on GD theory for analyzing CME-driven shock signatures.« less

Analysis of coronal H I Lyman alpha measurements from a rocket flight on 1979 April 13

NASA Technical Reports Server (NTRS)

Withbroe, G. L.; Kohl, J. L.; Weiser, H.; Noci, G.; Munro, R. H.

1982-01-01

It is noted that measurements of the profiles of resonantly scattered hydrogen Lyman-alpha coronal radiation have been used in determining hydrogen kinetic temperatures from 1.5 to 4 solar radii from sun center in a quiet region of the corona. Proton temperatures derived using the line widths decrease with height from 2.6 x 10 to the 6th K at 1.5 solar radii to 1.2 x 10 to the 6th K at 4 solar radii. These measurements, together with temperatures for lower heights determined from earlier Skylab and eclipse data, suggest that there is a maximum in the quiet coronal proton temperature at about 1.5 solar radii. Comparison of measured Lyman-alpha intensities with those calculated using a representative model for the radial variation of the coronal electron density yields information on the magnitude of the electron temperature gradient and suggests that the solar wind flow was subsonic for distances less than 4 solar radii.

The effects of large- and small-scale density structures on the radio from coronal streamers

NASA Astrophysics Data System (ADS)

Thejappa, G.; Kundu, M. R.

1994-01-01

The radio observations of the coronal streamers obtained using Clark Lake radioheliograph at 73.8, 50.0, and 38.5 MHz during a period of minimum activity in September 1986 are presented. Streamers appear to correlate with two prominent disk sources whose intensites fluctuated randomly. The variations in half-power diameter of the radio Sun are found to correspond with the variations in the white-light extents of the coronal streamers. It appears that the shape of the radio Sun is not a function of the phase of the solar cycle; instead it depends on the relative positions of the streamers in the corona. The observed peak brightness temperatures, TB, of the streamers are found to be very low, being approximately equal to 6 x 104 K. We compute the brightness temperature distribution along the equator by tracing the rays in the coronal plasma. The rays are deflected away by the streamers before reaching the critical density level, whereas they penetrate deeper into the coronal hole for small angles between the line of sight and the streamer axis. As a consequence, it is found that the streamers and coronal holes appear in the calculated equatorial brightness distribution as irregular brightness depressions and enhancements, respectively. The fine structures are found to disappear when the scattering due to small-scale density inhomogeneities is included in the ray-tracing calculations. The required relative level of density fluctuations, epsilon1 = (delta N)/N, is found to be greater than 12% to reduce the peak brightness temperature from 106 K to 6 x 104 K for all the three frequencies.

STEREO OBSERVATIONS OF FAST MAGNETOSONIC WAVES IN THE EXTENDED SOLAR CORONA ASSOCIATED WITH EIT/EUV WAVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, Ryun-Young; Ofman, Leon; Kramar, Maxim

2013-03-20

We report white-light observations of a fast magnetosonic wave associated with a coronal mass ejection observed by STEREO/SECCHI/COR1 inner coronagraphs on 2011 August 4. The wave front is observed in the form of density compression passing through various coronal regions such as quiet/active corona, coronal holes, and streamers. Together with measured electron densities determined with STEREO COR1 and Extreme UltraViolet Imager (EUVI) data, we use our kinematic measurements of the wave front to calculate coronal magnetic fields and find that the measured speeds are consistent with characteristic fast magnetosonic speeds in the corona. In addition, the wave front turns outmore » to be the upper coronal counterpart of the EIT wave observed by STEREO EUVI traveling against the solar coronal disk; moreover, stationary fronts of the EIT wave are found to be located at the footpoints of deflected streamers and boundaries of coronal holes, after the wave front in the upper solar corona passes through open magnetic field lines in the streamers. Our findings suggest that the observed EIT wave should be in fact a fast magnetosonic shock/wave traveling in the inhomogeneous solar corona, as part of the fast magnetosonic wave propagating in the extended solar corona.« less

Hi-C Observations of an Active Region Corona, and Investigation of the Underlying Magnetic Structure

NASA Technical Reports Server (NTRS)

Tiwari, S. K.; Alexander, C. E.; Winebarger, A.; Moore, R. L.

2014-01-01

The solar corona is much hotter (>=10(exp 6) K) than its surface (approx 6000 K), puzzling astrophysicists for several decades. Active region (AR) corona is again hotter than the quiet Sun (QS) corona by a factor of 4-10. The most widely accepted mechanism that could heat the active region corona is the energy release by current dissipation via reconnection of braided magnetic field structure, first proposed by E. N. Parker three decades ago. The first observational evidence for this mechanism has only recently been presented by Cirtain et al. by using High-resolution Coronal Imager (Hi-C) observations of an AR corona at a spatial resolution of 0.2 arcsec, which is required to resolve the coronal loops, and was not available before the rocket flight of Hi-C in July 2012. The Hi-C project is led by NASA/MSFC. In the case of the QS, work done by convection/granulation on the inter-granular feet of the coronal field lines translates into the heat observed in the corona. In the case of the AR, as here, there could be flux emergence, cancellation/submergence, or shear flows generating large stress and tension in coronal field loops which is released as heat in the corona. We are currently investigating the changes taking place in photospheric feet of the magnetic field involved with brightenings in the Hi-C AR corona. For this purpose, we are also using SDO/AIA data of +/- 2 hours around the 5 minutes Hi-C flight. In the present talk, I will first summarize some of the results of the Hi-C observations and then present some results from our recent analysis on what photospheric processes feed the magnetic energy that dissipates into heat in coronal loops.

FE-XIII Infrared / FE-XIV Green Line Ratio Diagnostics (P55)

NASA Astrophysics Data System (ADS)

Srivastava, A. K.; et al.

2006-11-01

aks.astro.itbhu@gmail.com We consider the first 27-level atomic model of Fe XIII (5.9 < log Te < 6.4 K) to estimate its ground level populations, taking account of electron as well as proton collisional excitations and de-excitations, radiative cascades, radiative excitations and de-excitations. Radiative cascade is important but the effect of dilution factor is negligible at higher electron densities. The 3 P1-3P0 and 3P2-3P1 transitions in the ground configuration 3s2 3p2 of Fe XIII result in two forbidden coronal emission lines in the infrared region, namely 10747 Å and 10798 Å., while the 5303 Å green line is formed in the 3s2 3p 2 2 ground configuration of Fe XIV as a result of P3 / 2 - P1 / 2 magnetic dipole transition. The line-widths of appropriate pair of forbidden coronal emission lines observed simultaneously can be useful diagnostic tool to deduce temperature and non-thermal velocity in the large scale coronal structures using intensity ratios of the lines as the temperature signature, instead of assuming ion temperature to be equal to the electron temperature. Since the line intensity ratios IG5303/IIR10747 and IG5303/IIR10798 have very week density dependence, they are ideal monitors of temperature mapping in the solar corona.

SOHO Observations of a Coronal Mass Ejection

NASA Astrophysics Data System (ADS)

Akmal, Arya; Raymond, John C.; Vourlidas, Angelos; Thompson, Barbara; Ciaravella, A.; Ko, Y.-K.; Uzzo, M.; Wu, R.

2001-06-01

We describe a coronal mass ejection (CME) observed on 1999 April 23 by the Ultraviolet Coronagraph Spectrometer (UVCS), the Extreme-Ultraviolet Imaging Telescope (EIT), and the Large-Angle and Spectrometric Coronagraphs (LASCO) aboard the Solar and Heliospheric Observatory (SOHO). In addition to the O VI and C III lines typical of UVCS spectra of CMEs, this 480 km s-1 CME exhibits the forbidden and intercombination lines of O V at λλ1213.8 and 1218.4. The relative intensities of the O V lines represent an accurate electron density diagnostic not generally available at 3.5 Rsolar. By combining the density with the column density derived from LASCO, we obtain the emission measure of the ejected gas. With the help of models of the temperature and time-dependent ionization state of the expanding gas, we determine a range of heating rates required to account for the UV emission lines. The total thermal energy deposited as the gas travels to 3.5 Rsolar is comparable to the kinetic and gravitational potential energies. We note a core of colder material radiating in C III, surrounded by hotter material radiating in the O V and O VI lines. This concentration of the coolest material into small regions may be a common feature of CMEs. This event thus represents a unique opportunity to describe the morphology of a CME, and to characterize its plasma parameters.

Latitudinal variability of large-scale coronal temperature and its association with the density and the global magnetic field

NASA Technical Reports Server (NTRS)

Guhathakurta, M.; Fisher, R. R.

1994-01-01

In this paper we utilize the latitiude distribution of the coronal temperature during the period 1984-1992 that was derived in a paper by Guhathakurta et al, 1993, utilizing ground-based intensity observations of the green (5303 A Fe XIV) and red (6374 A Fe X) coronal forbidden lines from the National Solar Observatory at Sacramento Peak, and establish it association with the global magnetic field and the density distributions in the corona. A determination of plasma temperature, T, was estimated from the intensity ratio Fe X/Fe XIV (where T is inversely proportional to the ratio), since both emission lines come from ionized states of Fe, and the ratio is only weakly dependent on density. We observe that there is a large-scale organization of the inferred coronal temperature distribution that is associated with the large-scale, weak magnetic field structures and bright coronal features; this organization tends to persist through most of the magnetic activity cycle. These high-temperature structures exhibit time-space characteristics which are similar to those of the polar crown filaments. This distribution differs in spatial and temporal characterization from the traditional picture of sunspot and active region evolution over the range of the sunspot cycle, which are manifestations of the small-scale, strong magnetic field regions.

X-Ray Properties of Low-mass Pre-main Sequence Stars in the Orion Trapezium Cluster

NASA Astrophysics Data System (ADS)

Schulz, Norbert S.; Huenemoerder, David P.; Günther, Moritz; Testa, Paola; Canizares, Claude R.

2015-09-01

The Chandra HETG Orion Legacy Project (HOLP) is the first comprehensive set of observations of a very young massive stellar cluster that provides high-resolution X-ray spectra of very young stars over a wide mass range (0.7-2.3 {M}⊙ ). In this paper, we focus on the six brightest X-ray sources with T Tauri stellar counterparts that are well-characterized at optical and infrared wavelengths. All stars show column densities which are substantially smaller than expected from optical extinction, indicating that the sources are located on the near side of the cluster with respect to the observer as well as that these stars are embedded in more dusty environments. Stellar X-ray luminosities are well above 1031 erg s-1, in some cases exceeding 1032 erg s-1 for a substantial amount of time. The stars during these observations show no flares but are persistently bright. The spectra can be well fit with two temperature plasma components of 10 MK and 40 MK, of which the latter dominates the flux by a ratio 6:1 on average. The total emission measures range between 3-8 × 1054 cm-3 and are comparable to active coronal sources. The fits to the Ne ix He-Like K-shell lines indicate forbidden to inter-combination line ratios consistent with the low-density limit. Observed abundances compare well with active coronal sources underlying the coronal nature of these sources. The surface flux in this sample of 0.6-2.3 {M}⊙ classical T Tauri stars shows that coronal activity increases significantly between ages 0.1 and 10 Myr. The results demonstrate the power of X-ray line diagnostics to study coronal properties of T Tauri stars in young stellar clusters.

Evaluation of time required for recontamination of coronally sealed canals medicated with calcium hydroxide and chlorhexidine.

PubMed

Gomes, B P F A; Sato, E; Ferraz, C C R; Teixeira, F B; Zaia, A A; Souza-Filho, F J

2003-09-01

To determine in vitro the time required for recontamination of coronally sealed canals medicated with either calcium hydroxide (CaOH2), 2% chlorhexidine gel (CG) or with a combination of both. Eighty intact, caries-free, premolar teeth with straight roots and mature apices were selected for the study. After biomechanical preparation of 75 teeth, they were randomly divided into nine groups according to the intracanal medicament and the coronal seal with 'Intermediate Restorative Material' (IRM) as follows: (i) 10 teeth medicated with CG, coronally unsealed; (ii) 10 teeth medicated with CaOH2, coronally unsealed; (iii) 10 teeth medicated with CaOH2 + CG, coronally unsealed; (iv) 10 teeth medicated with CG + coronal seal; (v) 10 teeth medicated with CaOH2 + coronal seal; (vi) 10 teeth medicated with CG + CaOH2 + coronal seal; (vii) 10 teeth without intracanal medicament and coronally sealed; (viii) 5 teeth without intracanal medicament and coronally unsealed, used as the positive control group (PC); (ix) 5 teeth with intact crowns used as the negative control group (NC). Glass flasks were filled with Brain Heart Infusion broth (BHI), so that only the root apex was in contact with the broth, while the crown was immersed in human saliva + BHI (3:1). The flasks were then incubated at 37 degrees C in an atmosphere of 10% CO2, and microbial growth was checked daily. All specimens of the PC showed contamination within 1 day of incubation, while the NC showed no evidence of broth turbidity. Recontamination was detected after an average time of 3.7 days in the unsealed canals medicated with CG, 1.8 days in the group medicated with CaOH2 and 2.6 days in the group medicated with CaOH2 + CG. When the crowns were sealed with IRM, recontamination was detected within 13.5 days in the canals medicated with CG, after 17.2 days in the group medicated with CaOH2 and after 11.9 days in the group medicated with CG + CaOH2. The group with no medication, but sealed with IRM, showed recontamination after 8.7 days. There were statistically significant differences between the teeth with or without coronal seal (P<0.05). The coronal seal delayed but did not prevent leakage of microorganisms. There was no difference between the various medicaments.

The XMM-Newton View of Stellar Coronae: High-Resolution X-Ray Spectroscopy of Capella

NASA Technical Reports Server (NTRS)

Audard, M.; Behar, E.; Guedel, M.; Raassen, A. J. J.; Porquet, D.; Mewe, R.; Foley, C. A.; Bromage, G. E.

2000-01-01

We present the high-resolution RGS spectrum of the bright stellar binary Capella observed by the XMM-Newton satellite. A multi-thermal approach has been applied to fit the data and derive elemental abundances. The differential emission measure distribution is reconstructed using a Chebychev polynomial fit. The DEM shape is found to display a sharp peak around 7 MK, consistent with previous EUVE and ASCA results. A small but significant amount of emission measure is required around 1.8 MK in order to explain the O VII He-like triplet and the C VI Ly(alpha) line. Using the sensitivity to temperature of dielectronic recombination lines from O VI around 22 A, we confirm that the cool plasma temperature needs to be higher than 1.2 MK. In the approximation of a cool plasma described by one temperature, we used line ratios from the forbidden, intercombination, and resonance lines of the O VII triplet and derived an average density for the cool coronal plasma at the low density limit. A tentative study of line ratios from the M XI triplet gives an average temperature close to the sharp peak in emission measure and an average density of the order of 10(exp 12)cu cm, three orders of magnitude higher than for O VII. Implications for the coronal physics of Capella are discussed. We complement this paper with a discussion of the importance of the atomic code uncertainties on the spectral fitting procedure.

White-Light and Radioastronomical Remote-Sensing of Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Kooi, Jason E.; Spangler, Steven R.

2017-01-01

Coronal mass ejections (CMEs) are large-scale eruptions of plasma from the Sun that play an important role in space weather. Faraday rotation (FR) is the rotation of the plane of polarization that results when a linearly polarized signal passes through a magnetized plasma (such as a CME) and is proportional to the path integral through the plasma of the electron density and the line-of-sight component of the magnetic field. FR observations of a source near the Sun can provide information on the plasma structure of a CME shortly after launch; however, separating the contribution of the plasma density from the line-of-sight magnetic field is challenging.We report on simultaneous white-light and radio observations made of three CMEs in August 2012. We made radio observations using the Very Large Array (VLA) at 1 - 2 GHz frequencies of a "constellation" of radio sources through the solar corona at heliocentric distances that ranged from 6 - 15 solar radii: two sources (0842+1835 and 0900+1832) were occulted by a single CME and one source (0843+1547) was occulted by two CMEs. In addition to our radioastronomical observations, which represent one of the first active hunts for CME Faraday rotation since Bird et al. (1985) and the first active hunt using the VLA, we obtained white-light coronagraph images from the LASCO/C3 instrument to determine the Thomson scattering brightness (BT), providing a means to independently estimate the plasma density and determine its contribution to the observed Faraday rotation.A constant density force-free flux rope embedded in the background corona was used to model the effects of the CMEs on BT and FR and infer the plasma densities (6 - 22 x 103 cm-3) and axial magnetic field strengths (2 - 12 mG) for the three CMEs. A single flux rope model successfully reproduces the observed BT and FR profiles for 0842+1835 and 0900+1832; however 0843+1547 was occulted by two CMEs. Using the multiple viewpoints provided by LASCO/C3 and STEREO-A/COR2, we model observations of 0843+1547 using two flux ropes embedded in the background corona and demonstrate the model's ability to successfully reproduce both BT and FR profiles.

Study of the solar corona using radio and space observations

NASA Technical Reports Server (NTRS)

Dulk, G. A.

1984-01-01

The physics of coronal transients, the characteristics of radiation and accelerated particles at the time of flares, and the density/temperature structure of the transition region and corona and the coronal magnetic field are investigated.

The Helios Faraday Rotation Data Archive

NASA Astrophysics Data System (ADS)

Bird, M. K.; Volland, H.; Levy, G. S.; Stelzried, C. T.; Seidel, B. L.; Efimov, A. I.; Andreev, V. E.; Samoznaev, L. N.

2003-09-01

The Helios Faraday Rotation (FR) Experiment, a passive radio science investigation requiring no on-board hardware other than the existing spacecraft radio subsystem, was designed to study the dynamic and quiescent structure of the magnetic fields and electron density in the solar corona. Measurements of coronal Faraday rotation were derived from the linearly polarized S-band downlink carrier signal, which probed otherwise inaccessible regions of the corona in the radial range from 2 to 15 solar radii during the regularly recurring solar conjunctions. More than 1250 hours of Helios FR data were recorded over the duration of the Helios 1 (1974-84) and Helios 2 (1976-80) missions. The time scales of FR variations provide information on various physical phenomena: (a) slowly-varying rise and fall associated with the changing ray path offset, combined with the rotation of the quasi-static corona; (b) ubiquitous random oscillations with higher fluctuation amplitude at smaller solar offset distances, probably caused by coronal Alfvén waves; (c) occasional nearly discontinous jumps in the polarization angle, most likely caused by transient events such as coronal mass ejections (CMEs). The Helios FR data, aspects of which have been reported in more than forty publications to date, have now been systematically collected in a data archive for public dissemination. A brief review of the main results of the Helios FR Experiment are presented, together with some suggestions for possible use of the archive for continued solar wind research.

Segmentation of photospheric magnetic elements corresponding to coronal features to understand the EUV and UV irradiance variability

NASA Astrophysics Data System (ADS)

Zender, J. J.; Kariyappa, R.; Giono, G.; Bergmann, M.; Delouille, V.; Damé, L.; Hochedez, J.-F.; Kumara, S. T.

2017-09-01

Context. The magnetic field plays a dominant role in the solar irradiance variability. Determining the contribution of various magnetic features to this variability is important in the context of heliospheric studies and Sun-Earth connection. Aims: We studied the solar irradiance variability and its association with the underlying magnetic field for a period of five years (January 2011-January 2016). We used observations from the Large Yield Radiometer (LYRA), the Sun Watcher with Active Pixel System detector and Image Processing (SWAP) on board PROBA2, the Atmospheric Imaging Assembly (AIA), and the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamics Observatory (SDO). Methods: The Spatial Possibilistic Clustering Algorithm (SPoCA) is applied to the extreme ultraviolet (EUV) observations obtained from the AIA to segregate coronal features by creating segmentation maps of active regions (ARs), coronal holes (CHs) and the quiet sun (QS). Further, these maps are applied to the full-disk SWAP intensity images and the full-disk (FD) HMI line-of-sight (LOS) magnetograms to isolate the SWAP coronal features and photospheric magnetic counterparts, respectively. We then computed full-disk and feature-wise averages of EUV intensity and line of sight (LOS) magnetic flux density over ARs/CHs/QS/FD. The variability in these quantities is compared with that of LYRA irradiance values. Results: Variations in the quantities resulting from the segmentation, namely the integrated intensity and the total magnetic flux density of ARs/CHs/QS/FD regions, are compared with the LYRA irradiance variations. We find that the EUV intensity over ARs/CHs/QS/FD is well correlated with the underlying magnetic field. In addition, variations in the full-disk integrated intensity and magnetic flux density values are correlated with the LYRA irradiance variations. Conclusions: Using the segmented coronal features observed in the EUV wavelengths as proxies to isolate the underlying magnetic structures is demonstrated in this study. Sophisticated feature identification and segmentation tools are important in providing more insights into the role of various magnetic features in both the short- and long-term changes in the solar irradiance. The movie associated to Fig. 2 is available at http://www.aanda.org

Low-Latitude Solar Wind During the Fall 1998 SOHO-Ulysses Quadrature

NASA Technical Reports Server (NTRS)

Poletto, G.; Suess, Steven T.; Biesecker, D.; Esser, R.; Gloeckler, G.; Zurbuchen, T.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The Fall 1998 SOlar-Heliospheric Observatory (SOHO) - Ulysses quadrature occurred when Ulysses was at 5.2 AU, 17.4 deg South of the equator, and off the West line of the Sun. SOHO coronal observations, at heliocentric distances of a few solar radii, showed that the line through the solar center and Ulysses crossed, over the first days of observations, a dark, weakly emitting area and through the northern edge of a streamer complex during the second half of the quadrature campaign. Ulysses in situ observations showed this transition to correspond to a decrease from higher speed wind typical of coronal hole flow to low speed wind. Physical parameters (density, temperature, flow speed) of the low latitude coronal plasma sampled over the campaign are determined using constraints from what is the same plasma measured later in situ and simulating the intensities of the Hydrogen Lyman-alpha and OVI 1032 and 1037 Angstrom lines, measured by the Ultra Violet Coronagraph Spectrometer (UVCS) on SOHO. The densities, temperatures and outflow speed are compared with the same characteristic flow parameters for high-latitude fast wind streams and typical slow solar wind.

Anomalous Surge of the White-Light Corona at the Onset of the Declining Phase of Solar Cycle 24

NASA Astrophysics Data System (ADS)

Lamy, P.; Boclet, B.; Wojak, J.; Vibert, D.

2017-04-01

In late 2014, when the current Solar Cycle 24 entered its declining phase, the white-light corona as observed by the LASCO-C2 coronagraph underwent an unexpected surge that increased its global radiance by 60%, reaching a peak value comparable to the peak values of the more active Solar Cycle 23. A comparison of the temporal variation of the white-light corona with the variations of several indices and proxies of solar activity indicate that it best matches the variation of the total magnetic field. The daily variations point to a localized enhancement or bulge in the electron density that persisted for several months. Carrington maps of the radiance and of the HMI photospheric field allow connecting this bulge to the emergence of the large sunspot complex AR 12192 in October 2014, the largest since AR 6368 observed in November 1990. The resulting unusually high increase of the magnetic field and the distortion of the neutral sheet in a characteristic inverse S-shape caused the coronal plasma to be trapped along a similar pattern. A 3D reconstruction of the electron density based on time-dependent solar rotational tomography supplemented by 2D inversion of the coronal radiance confirms the morphology of the bulge and reveals that its level was well above the standard models of a corona of the maximum type, by typically a factor of 3. A rather satisfactory agreement is found with the results of the thermodynamic MHD model produced by Predictive Sciences, although discrepancies are noted. The specific configuration of the magnetic field that led to the coronal surge resulted from the interplay of various factors prevailing at the onset of the declining phase of the solar cycles, which was particularly efficient in the case of Solar Cycle 24.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R., E-mail: spatsour@cc.uoi.gr, E-mail: james.a.klimchuk@nasa.gov

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding ≈50 km s{sup –1}. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe XIV lines at 264.78 and 274.20more » Å is used to determine wing and core densities. We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe XIV lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.« less

Coronal loop seismology using damping of standing kink oscillations by mode coupling

NASA Astrophysics Data System (ADS)

Pascoe, D. J.; Goddard, C. R.; Nisticò, G.; Anfinogentov, S.; Nakariakov, V. M.

2016-05-01

Context. Kink oscillations of solar coronal loops are frequently observed to be strongly damped. The damping can be explained by mode coupling on the condition that loops have a finite inhomogeneous layer between the higher density core and lower density background. The damping rate depends on the loop density contrast ratio and inhomogeneous layer width. Aims: The theoretical description for mode coupling of kink waves has been extended to include the initial Gaussian damping regime in addition to the exponential asymptotic state. Observation of these damping regimes would provide information about the structuring of the coronal loop and so provide a seismological tool. Methods: We consider three examples of standing kink oscillations observed by the Atmospheric Imaging Assembly (AIA) of the Solar Dynamics Observatory (SDO) for which the general damping profile (Gaussian and exponential regimes) can be fitted. Determining the Gaussian and exponential damping times allows us to perform seismological inversions for the loop density contrast ratio and the inhomogeneous layer width normalised to the loop radius. The layer width and loop minor radius are found separately by comparing the observed loop intensity profile with forward modelling based on our seismological results. Results: The seismological method which allows the density contrast ratio and inhomogeneous layer width to be simultaneously determined from the kink mode damping profile has been applied to observational data for the first time. This allows the internal and external Alfvén speeds to be calculated, and estimates for the magnetic field strength can be dramatically improved using the given plasma density. Conclusions: The kink mode damping rate can be used as a powerful diagnostic tool to determine the coronal loop density profile. This information can be used for further calculations such as the magnetic field strength or phase mixing rate.

OSO 8 observational limits to the acoustic coronal heating mechanism

NASA Technical Reports Server (NTRS)

Bruner, E. C., Jr.

1981-01-01

An improved analysis of time-resolved line profiles of the C IV resonance line at 1548 A has been used to test the acoustic wave hypothesis of solar coronal heating. It is shown that the observed motions and brightness fluctuations are consistent with the existence of acoustic waves. Specific account is taken of the effect of photon statistics on the observed velocities, and a test is devised to determine whether the motions represent propagating or evanescent waves. It is found that on the average about as much energy is carried upward as downward such that the net acoustic flux density is statistically consistent with zero. The statistical uncertainty in this null result is three orders of magnitue lower than the flux level needed to heat the corona.

Temperature Structure of a Coronal Cavity

NASA Technical Reports Server (NTRS)

Kucera, T. A.; Gibson, S. E.; Schmit, D. J.

2011-01-01

we analyze the temperature structure of a coronal cavity observed in Aug. 2007. coronal cavities are long, low-density structures located over filament neutral lines and are often seen as dark elliptical features at the solar limb in white light, EUV and x-rays. when these structures erupt they form the cavity portions of CMEs. It is important to establish the temperature structure of cavities in order to understand the thermodynamics of cavities in relation to their three-dimensional magnetic structure. To analyze the temperature we compare temperature ratios of a series of iron lines observed by the Hinode/EUv Imaging spectrometer (EIS). We also use those lines to constrain a forward model of the emission from the cavity and streamer. The model assumes a coronal streamer with a tunnel-like cavity with elliptical cross-section and a Gaussian variation of height along the tunnel lenth. Temperature and density can be varied as a function of altitude both in the cavity and streamer. The general cavity morphology and the cavity and streamer density have already been modeled using data from STEREO's SECCHI/EUVI and Hinode/EIS (Gibson et al 2010 and Schmit & Gibson 2011).

The coronal structure of active regions

NASA Technical Reports Server (NTRS)

Landini, M.; Monsignori Fossi, B. C.; Krieger, A.; Vaiana, G. S.

1975-01-01

A four-parameter model, which assumes a Gaussian dependence of both temperature and pressure on distance from center, is used to fit the compact part of coronal active regions as observed in X-ray photographs from a rocket experiment. The four parameters are the maximum temperature, the maximum pressure, the width of the pressure distribution, and the width of the temperature distribution. The maximum temperature ranges from 2.2 to 2.8 million K, and the maximum density from 2 to 9 by 10 to the 9th power per cu cm. The range of the pressure-distribution width is from 2 to 4 by 10 to the 9th power cm and that of the temperature-distribution width from 2 to 7.

Stereoscopy and Tomography of Coronal Structures

NASA Astrophysics Data System (ADS)

de Patoul, J.

2012-04-01

The hot solar corona consists of a low density plasma, which is highly structured by the magnetic field. To resolve and study the corona, several solar Ultraviolet (UV) and X-ray telescopes are operated with high spatial and temporal resolution. EUV (Extreme UV) image sequences of the lower solar corona have revealed a wide variety of structures with sizes ranging from the Sun's diameter to the limit of the angular resolution. Active regions can be observed with enhanced temperature and density, as well as 'quiet' regions, coronal holes with lower density and numerous other transient phenomena such as plumes, jets, bright points, flares, filaments, coronal mass ejections, all structured by the coronal magnetic field. In this work, we analyze polar plumes in a sequence of Solar EUV images taken nearly simultaneously by the three telescopes on board of the spacecraft STEREO/SECCHI A and B, and SOHO/EIT. Plumes appear in EUV images as elongated objects starting on the surface of the Sun extending super-radially into the corona. Their formation and contribution to the fast solar wind and other coronal phenomena are still under debate. Knowledge of the polar plume 3-D geometry can help to understand some of the physical processes in the solar corona. In this dissertation we develop new techniques for the characterization of polar plume structures in solar coronal images (Part II) then we analyze these structures using the techniques (Part III): We design a new technique capable of automatically identifying plumes in solar EUV images close to the limb at 1.01-1.39 Ro. This plume identification is based on a multi-scale Hough-wavelet analysis. We show that the method is well adapted to identifying the location, width and orientation of plumes. Starting from Hough-wavelet analysis, we elaborate on two other techniques to determine 3-D plume localization and structure: (i) tomography employing data from a single spacecraft over more than half a rotation and (ii) stereoscopy from simultaneous data observed by two or more spacecrafts. For tomography, we consider the filtered back projection method for which we incorporate the differential rotation of the Sun. For stereoscopy, we use three view directions for a conventional stereoscopic triangulation. These multi-scale Hough-wavelet analyses, stereoscopy and tomography extensions have been applied for the first time in a coronal plumes study. The temporal evolution of the mean orientation of plumes from May 2007 to April 2008 is then analyzed and discussed. Since the plume orientation is assumed to follow the coronal magnetic field, this analysis reveals: (i) a mean orientation of plumes more horizontal than for a dipole magnetic field, (ii) an asymmetry of the coronal open polar cap magnetic field from the solar rotation axis by up to 6° and (iii) a variation of these orientation and asymmetry over the year. Finally, with the help of the reconstructed 3-D geometry of the plumes, we study in detail their temporal evolution as well as the shape and size of their cross sections. The study reveals: (i) different lifetimes of plumes from 2-3 days up to 9 days and (ii) the presence of both near-circular plume cross sections and plumes with curtain-like structures. Also discussed is the plumes positions and their relation to other coronal phenomena such as coronal holes and jets. Plumes are found to be located inside coronal holes, and jets could explain the intensity enhancement within the plumes.

Center-to-Limb Variability of Hot Coronal EUV Emissions During Solar Flares

NASA Astrophysics Data System (ADS)

Thiemann, E. M. B.; Chamberlin, P. C.; Eparvier, F. G.; Epp, L.

2018-02-01

It is generally accepted that densities of quiet-Sun and active region plasma are sufficiently low to justify the optically thin approximation, and this is commonly used in the analysis of line emissions from plasma in the solar corona. However, the densities of solar flare loops are substantially higher, compromising the optically thin approximation. This study begins with a radiative transfer model that uses typical solar flare densities and geometries to show that hot coronal emission lines are not generally optically thin. Furthermore, the model demonstrates that the observed line intensity should exhibit center-to-limb variability (CTLV), with flares observed near the limb being dimmer than those occurring near disk center. The model predictions are validated with an analysis of over 200 flares observed by the EUV Variability Experiment (EVE) on the Solar Dynamics Observatory (SDO), which uses six lines, with peak formation temperatures between 8.9 and 15.8 MK, to show that limb flares are systematically dimmer than disk-center flares. The data are then used to show that the electron column density along the line of sight typically increases by 1.76 × 10^{19} cm^{-2} for limb flares over the disk-center flare value. It is shown that the CTLV of hot coronal emissions reduces the amount of ionizing radiation propagating into the solar system, and it changes the relative intensities of lines and bands commonly used for spectral analysis.

Digging in the coronal graveyard - A Rosat observation of the red giant Arcturus

NASA Technical Reports Server (NTRS)

Ayres, Thomas R.; Fleming, Thomas A.; Schmitt, Juergen H. M. M.

1991-01-01

A deep exposure of the bright star Arcturus (Alpha Bootis: K1 III) with the Roentgensatellit (Rosat) failed to detect soft X-ray emission from the archetype 'noncoronal' red giant. The 3-sigma upper limit in the energy band 0.1-2.4 keV corresponds to an X-ray luminosity of less than 3 x 10 to the 25th erg/s, equivalent to a coronal surface flux density of less than 0.0001 solar. The nondetection safely eliminates coronal irradiation as a possible mechanism to produce the highly variable He I 10830 feature and emphasizes the sharp decline in solarlike coronal activity that accompanies the evolution of low-mass single stars away from the main sequence. While the most conspicuous object in the Rosat field of view was not visible in X-rays, at least one fainter star is among the about 60 sources recorded: the Sigma Sct variable CN Boo, an A8 giant in the UMa Stream.

Numerical Simulation of Coronal Waves Interacting with Coronal Holes. III. Dependence on Initial Amplitude of the Incoming Wave

NASA Astrophysics Data System (ADS)

Piantschitsch, Isabell; Vršnak, Bojan; Hanslmeier, Arnold; Lemmerer, Birgit; Veronig, Astrid; Hernandez-Perez, Aaron; Čalogović, Jaša

2018-06-01

We performed 2.5D magnetohydrodynamic (MHD) simulations showing the propagation of fast-mode MHD waves of different initial amplitudes and their interaction with a coronal hole (CH), using our newly developed numerical code. We find that this interaction results in, first, the formation of reflected, traversing, and transmitted waves (collectively, secondary waves) and, second, in the appearance of stationary features at the CH boundary. Moreover, we observe a density depletion that is moving in the opposite direction of the incoming wave. We find a correlation between the initial amplitude of the incoming wave and the amplitudes of the secondary waves as well as the peak values of the stationary features. Additionally, we compare the phase speed of the secondary waves and the lifetime of the stationary features to observations. Both effects obtained in the simulation, the evolution of secondary waves, as well as the formation of stationary fronts at the CH boundary, strongly support the theory that coronal waves are fast-mode MHD waves.

Signatures of Alfvén waves in the polar coronal holes as seen by EIS/Hinode

NASA Astrophysics Data System (ADS)

Banerjee, D.; Pérez-Suárez, D.; Doyle, J. G.

2009-07-01

Context: We diagnose the properties of the plume and interplume regions in a polar coronal hole and the role of waves in the acceleration of the solar wind. Aims: We attempt to detect whether Alfvén waves are present in the polar coronal holes through variations in EUV line widths. Methods: Using spectral observations performed over a polar coronal hole region with the EIS spectrometer on Hinode, we study the variation in the line width and electron density as a function of height. We use the density sensitive line pairs of Fe xii 186.88 Å and 195.119 Å and Fe xiii 203.82 Å and 202.04 Å. Results: For the polar region, the line width data show that the nonthermal line-of-sight velocity increases from 26~km s-1 at 10´´ above the limb to 42~km s-1 some 150´´ (i.e. ~110 000 km) above the limb. The electron density shows a decrease from 3.3 × 10^9~cm-3 to 1.9 × 10^8~cm-3 over the same distance. Conclusions: These results imply that the nonthermal velocity is inversely proportional to the quadratic root of the electron density, in excellent agreement with what is predicted for undamped radially propagating linear Alfvén waves. Our data provide signatures of Alfvén waves in the polar coronal hole regions, which could be important for the acceleration of the solar wind. Table [see full textsee full textsee full text] and Fig. [see full textsee full textsee full text] are only available in electronic form at http://www.aanda.org

Comment on: Polar Plumes and Fine-scale Coronal Structures - On the Interpretation of Coronal Radio Sounding Data by Patzold and Bird

NASA Technical Reports Server (NTRS)

Woo, R.; Habbal, S. R.

1998-01-01

Radio occultation measurements, which probe electron density over a wide dynamic range with high sensitivity and high spatial and temporal resolution reveal a solar corona permeated by a hierarchy of filamentary structures.

Spectroscopic Observations of a Solar Flare and the Associated Coronal Mass Ejection

NASA Astrophysics Data System (ADS)

Murray, S.; Tian, H.; McKillop, S.

2013-12-01

We used data from the EUV Imaging Spectrometer (EIS) on board Hinode to examine a coronal mass ejection and a preceding flare observed on 21 November 2012 between 15:00 and 17:00 UT. Images from the Atmospheric Imaging Assembly on the Solar Dynamics Observatory were used to align the data from EIS with specific events occurring. We analyzed spectra of a few emission lines at three locations on the flare site and one location in the erupting prominence. On the flare site, we found line profiles showing typical characteristics of chromospheric evaporation: downflows at cooler lines and upflows at hotter lines. At one particular location on the flare site, we clearly identified dominant downflows on the order of 100 km/s in lines through Fe VIII to Fe XVI. To the best of our knowledge, this is the first time that such strong high-speed downflows have been spectroscopically observed in the impulsive phase of solar flares. The profile of the Fe VIII 184.54 line reveals two peaks and we were able to use the double Gaussian fit to separate the rapid downflows of dense material from the nearly stationary coronal background emission. For the erupting prominence, we were able to analyze multiple lines, cooler and warmer, of interest using this double Gaussian fit to separate the background emission from the emission of the ejected material. Our results show that the LOS velocities of the ejected material are about 100 km/s in the lower corona. Additionally, in each region of interest, we used the ratio of the density-sensitive line pair FeXII 195/186 to determine the electron density. Our results clearly show that the coronal densities were greatly enhanced during the flare. The density of the ejected material is also much larger than the typical coronal density. This research was supported by the NSF grant for the Solar Physics REU Program at the Smithsonian Astrophysical Observatory (AGS-1263241).

Coronal imbalance in degenerative lumbar scoliosis: Prevalence and influence on surgical decision-making for spinal osteotomy.

PubMed

Bao, H; Yan, P; Qiu, Y; Liu, Z; Zhu, F

2016-09-01

There is a paucity of information on the pre-operative coronal imbalance in patients with degenerative lumbar scoliosis (DLS) and its influence on surgical outcomes. A total of 284 DLS patients were recruited into this study, among whom 69 patients were treated surgically and the remaining 215 patients conservatively Patients were classified based on the coronal balance distance (CBD): Type A, CBD < 3 cm; Type B, CBD > 3 cm and C7 Plumb Line (C7PL) shifted to the concave side of the curve; Type C, CBD > 3 cm and C7PL shifted to the convex side. A total of 99 of the 284 (34.8%) patient presented with a pre-operative coronal imbalance (mean CBD: 48.5, standard deviation 18.7 mm). More patients with a Type B malalignment were observed than with a Type C malalignment (62 versus 37). A total of 21 pf the 69 (30.4%) surgically treated patients had a post-operative coronal imbalance, which was found to be more prevalent in Type C patients (p < 0.001). At follow-up, less improvement was observed in terms of Short Form-36 Physical Component Score and visual analogue score for back pain (p = 0.034 and 0.025, respectively) in Type C patients. This study shows that patients with Type C coronal malalignment may be at greater risk of post-operative coronal imbalance following posterior osteotomy. Cite this article: Bone Joint J 2016;98-B:1227-33. ©2016 The British Editorial Society of Bone & Joint Surgery.

VLA Measurements of Faraday Rotation through Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Kooi, Jason E.; Fischer, Patrick D.; Buffo, Jacob J.; Spangler, Steven R.

2017-04-01

Coronal mass ejections (CMEs) are large-scale eruptions of plasma from the Sun, which play an important role in space weather. Faraday rotation is the rotation of the plane of polarization that results when a linearly polarized signal passes through a magnetized plasma such as a CME. Faraday rotation is proportional to the path integral through the plasma of the electron density and the line-of-sight component of the magnetic field. Faraday-rotation observations of a source near the Sun can provide information on the plasma structure of a CME shortly after launch. We report on simultaneous white-light and radio observations made of three CMEs in August 2012. We made sensitive Very Large Array (VLA) full-polarization observations using 1 - 2 GHz frequencies of a constellation of radio sources through the solar corona at heliocentric distances that ranged from 6 - 15 R_{⊙}. Two sources (0842+1835 and 0900+1832) were occulted by a single CME, and one source (0843+1547) was occulted by two CMEs. In addition to our radioastronomical observations, which represent one of the first active hunts for CME Faraday rotation since Bird et al. ( Solar Phys., 98, 341, 1985) and the first active hunt using the VLA, we obtained white-light coronagraph images from the Large Angle and Spectrometric Coronagraph (LASCO) C3 instrument to determine the Thomson-scattering brightness [BT], providing a means to independently estimate the plasma density and determine its contribution to the observed Faraday rotation. A constant-density force-free flux rope embedded in the background corona was used to model the effects of the CMEs on BT and Faraday rotation. The plasma densities (6 - 22×103 cm^{-3}) and axial magnetic-field strengths (2 - 12 mG) inferred from our models are consistent with the modeling work of Liu et al. ( Astrophys. J., 665, 1439, 2007) and Jensen and Russell ( Geophys. Res. Lett., 35, L02103, 2008), as well as previous CME Faraday-rotation observations by Bird et al. (1985).

Ionization in the local interstellar and intergalactic media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, K.

1990-01-01

Detailed photoionization calculations for the local interstellar medium (LISM) and the intergalactic medium (IGM) are presented. Constraints in the LISM are imposed by H I column density derived from IUE and Copernicus data toward nearby B stars and hot white dwarfs. The EUV radiation field is modeled including contributions from discrete stellar sources and from a thermal bremsstrahlung-radiative recombination spectrum emitted from the surrounding 10(exp 6) K coronal substrate. Lower limits to the fractional ionization of hydrogen and helium of 0.17 and 0.30 respectively are established. The derived limits have important implications for the interpretation of the H I andmore » He I backscattering results. The high He ionization fraction results primarily from very strong line emission below 500 A originating in the surrounding coronal substrate while the H ionization is dominated by the EUV radiation from the discrete stellar sources. The dual effects of thermal conduction and the EUV spectrum of the 10(exp 6) K plasma on ionization in the cloud skin are explored. The EUV radiation field and Auger ionization have insignificant effects on the resulting ionic column densities of Si IV, C IV, N V and O VI through the cloud skin. Calculations show that the abundances of these species are dominated by collisional ionization in the thermal conduction front. Because of a low charge exchange rate with hydrogen, the ionic column density ratios of N(C III)/N(C II) and N(N II)/N(N I) are dominated by the EUV radiation field in the local interstellar medium. These ratios should be important diagnostics for the EUV radiation field and serve as surrogate indicators of the interstellar He and H ionization fraction respectively. The same photoionization model is applied to the intergalactic medium.« less

MAGNETIC UNTWISTING IN SOLAR JETS THAT GO INTO THE OUTER CORONA IN POLAR CORONAL HOLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Ronald L.; Sterling, Alphonse C.; Falconer, David A., E-mail: ron.moore@nasa.gov

We study 14 large solar jets observed in polar coronal holes. In EUV movies from the Solar Dynamics Observatory/Atmospheric Imaging Assembly (AIA), each jet appears similar to most X-ray jets and EUV jets that erupt in coronal holes; but each is exceptional in that it goes higher than most, so high that it is observed in the outer corona beyond 2.2 R{sub Sun} in images from the Solar and Heliospheric Observatory/Large Angle Spectroscopic Coronagraph (LASCO)/C2 coronagraph. From AIA He ii 304 Å movies and LASCO/C2 running-difference images of these high-reaching jets, we find: (1) the front of the jet transitsmore » the corona below 2.2 R{sub Sun} at a speed typically several times the sound speed; (2) each jet displays an exceptionally large amount of spin as it erupts; (3) in the outer corona, most of the jets display measureable swaying and bending of a few degrees in amplitude; in three jets the swaying is discernibly oscillatory with a period of order 1 hr. These characteristics suggest that the driver in these jets is a magnetic-untwisting wave that is basically a large-amplitude (i.e., nonlinear) torsional Alfvén wave that is put into the reconnected open field in the jet by interchange reconnection as the jet erupts. From the measured spinning and swaying, we estimate that the magnetic-untwisting wave loses most of its energy in the inner corona below 2.2 R{sub Sun}. We point out that the torsional waves observed in Type-II spicules might dissipate in the corona in the same way as the magnetic-untwisting waves in our big jets, and thereby power much of the coronal heating in coronal holes.« less

ATM observations - X-ray results. [solar coronal structure from Skylab experiments

NASA Technical Reports Server (NTRS)

Vaiana, G. S.; Zombeck, M.; Krieger, A. S.; Timothy, A. F.

1976-01-01

Preliminary results of the solar X-ray observations from Skylab are reviewed which indicate a highly structured nature for the corona, with closed magnetic-loop structures over a wide range of size scales. A description of the S-054 experiments is provided, and values are given for the parameters - including size, density, and temperature - describing a variety of typical coronal features. The structure and evolution of active regions, coronal holes, and bright points are discussed.

The solar atmosphere and the structure of active regions

NASA Technical Reports Server (NTRS)

Sturrock, P. A.

1974-01-01

The existence of 'holes' in the corona is reported characterized by abnormally low densities and temperatures. It was found that such coronal holes appear to be the source of high-velocity, enhanced-density streams in the solar wind as observed at the earth's orbit. It was further noted that coronal holes appear to be associated with regions of diverging magnetic fields in the corona. Models were developed to accomplish the objective for the principal energy flows in the transition region and corona.

SELF-ORGANIZATION OF RECONNECTING PLASMAS TO MARGINAL COLLISIONALITY IN THE SOLAR CORONA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imada, S.; Zweibel, E. G.

We explore the suggestions by Uzdensky and Cassak et al. that coronal loops heated by magnetic reconnection should self-organize to a state of marginal collisionality. We discuss their model of coronal loop dynamics with a one-dimensional hydrodynamic calculation. We assume that many current sheets are present, with a distribution of thicknesses, but that only current sheets thinner than the ion skin depth can rapidly reconnect. This assumption naturally causes a density-dependent heating rate which is actively regulated by the plasma. We report nine numerical simulation results of coronal loop hydrodynamics in which the absolute values of the heating rates aremore » different but their density dependences are the same. We find two regimes of behavior, depending on the amplitude of the heating rate. In the case that the amplitude of heating is below a threshold value, the loop is in stable equilibrium. Typically, the upper and less dense part of a coronal loop is collisionlessly heated and conductively cooled. When the amplitude of heating is above the threshold, the conductive flux to the lower atmosphere required to balance collisionless heating drives an evaporative flow which quenches fast reconnection, ultimately cooling and draining the loop until the cycle begins again. The key elements of this cycle are gravity and the density dependence of the heating function. Some additional factors are present, including pressure-driven flows from the loop top, which carry a large enthalpy flux and play an important role in reducing the density. We find that on average the density of the system is close to the marginally collisionless value.« less

Determination of plasma parameters from soft X-ray images for coronal holes /open magnetic field configurations/ and coronal large-scale structures /extended closed-field configurations/

NASA Technical Reports Server (NTRS)

Maxson, C. W.; Vaiana, G. S.

1977-01-01

In connection with high-quality solar soft X-ray images the 'quiet' features of the inner corona have been separated into two sharply different components, including the strongly reduced emission areas or coronal holes (CH) and the extended regions of looplike emission features or large-scale structures (LSS). Particular central meridian passage observations of the prominent CH1 on August 21, 1973, are selected for a quantitative study. Histogram photographic density distributions for full-disk images at other central meridian passages of CH 1 are also presented, and the techniques of converting low photographic density data to deposited energy are discussed, with particular emphasis on the problems associated with the CH data.

Coronal emission-line polarization from the statistical equilibrium of magnetic sublevels. II. Fe XIV 5303 A

DOE Office of Scientific and Technical Information (OSTI.GOV)

House, L.L.; Querfeld, C.W.; Rees, D.E.

1982-04-15

Coronal magnetic fields influence in the intensity and linear polarization of light scattered by coronal Fe XIV ions. To interpret polarization measurements of Fe XIV 5303 A coronal emission requires a detailed understanding of the dependence of the emitted Stokes vector on coronal magnetic field direction, electron density, and temperature and on height of origin. The required dependence is included in the solutions of statistical equilibrium for the ion which are solved explicitly for 34 magnetic sublevels in both the ground and four excited terms. The full solutions are reduced to equivalent simple analytic forms which clearly show the requiredmore » dependence on coronal conditions. The analytic forms of the reduced solutions are suitable for routine analysis of 5303 green line polarimetric data obtained at Pic du Midi and from the Solar Maximum Mission Coronagraph/Polarimeter.« less

Fast-sausage oscillations in coronal loops with smooth boundary

NASA Astrophysics Data System (ADS)

Lopin, I.; Nagorny, I.

2014-12-01

Aims: The effect of the transition layer (shell) in nonuniform coronal loops with a continuous radial density profile on the properties of fast-sausage modes are studied analytically and numerically. Methods: We modeled the coronal waveguide as a structured tube consisting of a cord and a transition region (shell) embedded within a magnetic uniform environment. The derived general dispersion relation was investigated analytically and numerically in the context of frequency, cut-off wave number, and the damping rate of fast-sausage oscillations for various values of loop parameters. Results: The frequency of the global fast-sausage mode in the loops with a diffuse (or smooth) boundary is determined mainly by the external Alfvén speed and longitudinal wave number. The damping rate of such a mode can be relatively low. The model of coronal loop with diffuse boundary can support a comparatively low-frequency, global fast-sausage mode of detectable quality without involving extremely low values of the density contrast. The effect of thin transition layer (corresponds to the loops with steep boundary) is negligible and produces small reductions of oscillation frequency and relative damping rate in comparison with the case of step-function density profile. Seismological application of obtained results gives the estimated Alfvén speed outside the flaring loop about 3.25 Mm/s.

A two-fluid model of the solar wind

NASA Technical Reports Server (NTRS)

Sandbaek, O.; Leer, E.; Holzer, T. E.

1992-01-01

A method is presented for the integration of the two-fluid solar-wind equations which is applicable to a wide variety of coronal base densities and temperatures. The method involves proton heat conduction, and may be applied to coronal base conditions for which subsonic-supersonic solar wind solutions exist.

The Large Angle Spectroscopic Coronagraph (LASCO): Visible light coronal imaging and spectroscopy

NASA Technical Reports Server (NTRS)

Brueckner, Guenter E.; Howard, Russell A.; Koomen, Martin J.; Korendyke, C.; Michels, D. J.; Socker, D. G.; Lamy, Philippe; Llebaria, Antoine; Maucherat, J.; Schwenn, Rainer

1992-01-01

The Large Angle Spectroscopic Coronagraph (LASCO) is a triple coronagraph being jointly developed for the Solar and Heliospheric Observatory (SOHO) mission. LASCO comprises three nested coronagraphs (C1, C2, and C3) that image the solar corona for 1.1 to 30 solar radii (C1: 1.1 to 3 solar radii, C2: 1.5 to 6 solar radii, and C3: 3 to 30.0 solar radii). The inner coronagraph (C1) is a newly developed mirror version of the classic Lyot coronagraph without an external occultor, while the middle coronagraph (C2) and the outer coronagraph (C3) are externally occulted instruments. High resolution coronal spectroscopy from 1.1 to 3 R solar radii can be performed by using a Fabry-Perot interferometer, which is part of C1. High volume memories and a high speed microprocessor enable extensive onboard image processing. Image compression by factors of 10 to 20 will result in the transmission of 10 to 20 full images per hour.

Coronal Heating Observed with Hi-C

NASA Technical Reports Server (NTRS)

Winebarger, Amy R.

2013-01-01

The recent launch of the High-Resolution Coronal Imager (Hi-C) as a sounding rocket has offered a new, different view of the Sun. With approx 0.3" resolution and 5 second cadence, Hi-C reveals dynamic, small-scale structure within a complicated active region, including coronal braiding, reconnection regions, Alfven waves, and flows along active region fans. By combining the Hi-C data with other available data, we have compiled a rich data set that can be used to address many outstanding questions in solar physics. Though the Hi-C rocket flight was short (only 5 minutes), the added insight of the small-scale structure gained from the Hi-C data allows us to look at this active region and other active regions with new understanding. In this talk, I will review the first results from the Hi-C sounding rocket and discuss the impact of these results on the coronal heating problem.

Triggering Scenario of Geo-effective Solar Eruption on 15 March 2015

NASA Astrophysics Data System (ADS)

Bamba, Yumi; Inoue, Satoshi; Hayashi, Keiji

2017-08-01

The largest magnetic storm so far, called St Patricks’s Day event, in the solar cycle 24 occurred on 17 March 2015. It was caused by fast coronal mass ejection (CME) on 15 March 2015 from solar active region (AR) NOAA 12297. Surprisingly, the CME is suggested to be related to a C9.1 flare while the large CME is usually corresponding to a large flare. The purpose of this study is to understand the onset mechanism of the huge solar eruption which caused big impact on a magnetic environment of the geospace. The magnetic field structure in the AR was complicated: There were several filaments including the one which erupted and caused the CME. We hence carefully investigated the photospheric magnetic field, brightenings observed in the region from the chromosphere to the corona, and the three-dimensional coronal magnetic field calculated through our nonlinear force-free field (NLFFF) model using photospheric vector magnetic field data from the Hinode SOT and the Solar Dynamics Observatory (SDO). We focused on the C2.4 flare occurred prior to the C9.1 flare and filament eruption. Through our provisional analysis covering long time span, we noticed the C2.4 flare prior to the C9.1 flare is important to understanding the dynamics of this AR system and the CME event. (1) There was a compact but noticeably highly twisted magnetic field structure. During the C2.4 flare, flux cancellation was seen on the photospheric magnetic field data. (2) The erupting filament is sustained by the coronal magnetic field prior to the flare, and C2.4 flaring site locates in the vicinity of one footpoint of them. (3) The top of the coronal loops sustaining the filament touch to a region where the torus instability would be expected.Therefore, we consider that the magnetic reconnection at the C2.4 flaring site changed the magnetic environment of the filament, destabilized the highly twisted magnetic field structure, and finally allowed the twisted magnetic field to erupt.

Density and white light brightness in looplike coronal mass ejections - Temporal evolution

NASA Technical Reports Server (NTRS)

Steinolfson, R. S.; Hundhausen, A. J.

1988-01-01

Three ambient coronal models suitable for studies of time-dependent phenomena were used to investigate the propagation of coronal mass ejections initiated in each atmosphere by an identical energy source. These models included those of a static corona with a dipole magnetic field, developed by Dryer et al. (1979); a steady polytropic corona with an equatorial coronal streamer, developed by Steinolfson et al. (1982); and Steinolfson's (1988) model of heated corona with an equatorial coronal streamer. The results indicated that the first model does not adequately represent the general characteristics of observed looplike mass ejections, and the second model simulated only some of the observed features. Only the third model, which included a heating term and a streamer, was found to yield accurate simulation of the mess ejection observations.

Hi-C Observations of an Active Region Corona, and Investigation of the Underlying Magnetic Structure

NASA Technical Reports Server (NTRS)

Tiwari, Sanjiv K.; Alexander, Caroline E.; Winebarger, Amy R.; Moore, Ronald L.

2014-01-01

Hi-C: first observational evidence of field line braiding in the AR corona; NLFFF extrapolations support. Flux emergence and/or cancellation in the coronal braided region generate large stresses and tension in the coronal field loops which is released as heat in the corona. The field in these sub-regions are highly sheared and have apparent high speed plasma flows, therefore, the contribution from shearing flows to power the coronal and transition region heating can not be ruled out! The spatial resolution of Hi-­C is five times better than AIA. The cadence of Hi-C is 2.5 - 6 times better than AIA. The 193 Å was selected because of the strong emission line of Fe XII (peak formation temperature of 1.5 MK). Hi-­C collected data for 345 s @ 5.4 s cadence. The Hi-C target region was NOAA AR 11520; 11 July 2012, 18:51-18:57 UT. NLFFF extrapolation confirms the braided structure, and free magnetic energy estimates in the given volume.

Elimination of motion and pulsation artifacts using BLADE sequences in knee MR imaging.

PubMed

Lavdas, Eleftherios; Mavroidis, Panayiotis; Hatzigeorgiou, Vasiliki; Roka, Violeta; Arikidis, Nikos; Oikonomou, Georgia; Andrianopoulos, Konstantinos; Notaras, Ioannis

2012-10-01

The purpose of this study is to evaluate the ability of proton density (PD)-BLADE sequences in reducing or even eliminating motion and pulsatile flow artifacts in knee magnetic resonance imaging examinations. Eighty consecutive patients, who had been routinely scanned for knee examination, participated in the study. The following pairs of sequences with and without BLADE were compared: (a) PD turbo spin echo (TSE) sagittal (SAG) fat saturation (FS) in 35 patients, (b) PD TSE coronal (COR) FS in 19 patients, (c) T2 TSE axial in 13 patients and (d) PD TSE SAG in 13 patients. Both qualitative and quantitative analyses were performed based on the signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR) and relative contrast (ReCon) measures of normal anatomic structures. The qualitative analysis was performed by experienced radiologists. Also, the presence of image motion and pulsation artifacts was evaluated. Based on the results of the SNR, CRN and ReCon for the different sequences and anatomical structures, the BLADE sequences were significantly superior in 19 cases, whereas the corresponding conventional sequences were significantly superior in only 6 cases. BLADE sequences eliminated motion artifacts in all the cases. However, motion artifacts were shown in (a) six PD TSE SAG FS, (b) three PD TSE COR FS, (c) three PD TSE SAG and (d) two T2 TSE axial conventional sequences. In our results, it was found that, in PD FS sequences (sagittal and coronal), the differences between the BLADE and conventional sequences regarding the elimination of motion and pulsatile flow artifacts were statistically significant. In all the comparisons, the PD FS BLADE sequences (coronal and sagittal) were significantly superior to the corresponding conventional sequences regarding the classification of their image quality. In conclusion, this technique appears to be capable to potentially eliminate motion and pulsatile flow artifacts in MR images. Copyright © 2012 Elsevier Inc. All rights reserved.

Vertebral derotation in adolescent idiopathic scoliosis causes hypokyphosis of the thoracic spine

PubMed Central

2012-01-01

Background The purpose of this study was to test the hypothesis that direct vertebral derotation by pedicle screws (PS) causes hypokyphosis of the thoracic spine in adolescent idiopathic scoliosis (AIS) patients, using computer simulation. Methods Twenty AIS patients with Lenke type 1 or 2 who underwent posterior correction surgeries using PS were included in this study. Simulated corrections of each patient’s scoliosis, as determined by the preoperative CT scan data, were performed on segmented 3D models of the whole spine. Two types of simulated extreme correction were performed: 1) complete coronal correction only (C method) and 2) complete coronal correction with complete derotation of vertebral bodies (C + D method). The kyphosis angle (T5-T12) and vertebral rotation angle at the apex were measured before and after the simulated corrections. Results The mean kyphosis angle after the C + D method was significantly smaller than that after the C method (2.7 ± 10.0° vs. 15.0 ± 7.1°, p < 0.01). The mean preoperative apical rotation angle of 15.2 ± 5.5° was completely corrected after the C + D method (0°) and was unchanged after the C method (17.6 ± 4.2°). Conclusions In the 3D simulation study, kyphosis was reduced after complete correction of the coronal and rotational deformity, but it was maintained after the coronal-only correction. These results proved the hypothesis that the vertebral derotation obtained by PS causes hypokyphosis of the thoracic spine. PMID:22691717

What is the optimal cutoff value of the axis-line-angle technique for evaluating trunk imbalance in coronal plane?

PubMed

Zhang, Rui-Fang; Fu, Yu-Chuan; Lu, Yi; Zhang, Xiao-Xia; Hu, Yu-Min; Zhou, Yong-Jin; Tian, Nai-Feng; He, Jia-Wei; Yan, Zhi-Han

2017-02-01

Accurately evaluating the extent of trunk imbalance in the coronal plane is significant for patients before and after treatment. We preliminarily practiced a new method, axis-line-angle technique (ALAT), for evaluating coronal trunk imbalance with excellent intra-observer and interobserver reliability. Radiologists and surgeons were encouraged to use this method in clinical practice. However, the optimal cutoff value of the ALAT for determination of the extent of coronal trunk imbalance has not been calculated up to now. The purpose of this study was to identify the cutoff value of the ALAT that best predicts a positive measurement point to assess coronal balance or imbalance. A retrospective study at a university affiliated hospital was carried out. A total of 130 patients with C7-central sacral vertical line (CSVL) >0 mm and aged 10-18 years were recruited in this study from September 2013 to December 2014. Data were analyzed to determine the optimal cutoff value of the ALAT measurement. The C7-CSVL and ALAT measurements were conducted respectively twice on plain film within a 2-week interval by two radiologists. The optimal cutoff value of the ALAT was analyzed via receiver operating characteristic (ROC) curve. Comparison variables were performed with chi-square test between the C7-CSVL and ALAT measurements for evaluating trunk imbalance. Kappa agreement coefficient method was used to test the intra-observer and interobserver agreement of C7-CSVL and ALAT. The ROC curve area for the ALAT was 0.82 (95% confidence interval: 0.753-0.894, p<.001). The maximum Youden index was 0.51, and the corresponding cutoff point was 2.59°. No statistical difference was found between the C7-CSVL and ALAT measurements for evaluating trunk imbalance (p>.05). Intra-observer agreement values for the C7-CSVL measurements by observers 1 and 2 were 0.79 and 0.91 (p<.001), respectively, whereas intra-observer agreement values for the ALAT measurements were both 0.89 by observers 1 and 2 (p<.001). The interobserver agreement values for the first and second measurements with the C7-CSVL were 0.78 and 0.85 (p<.001), respectively, whereas the interobserver agreement values for the first and second measurements with the ALAT were 0.91 and 0.88 (p<.001), respectively. The newly developed ALAT provided an acceptable optimal cutoff value for evaluating trunk imbalance in the coronal plane with a high level of intra-observer and interobserver agreement, which suggests that the ALAT is suitable for clinical use. Copyright © 2016 Elsevier Inc. All rights reserved.

Ephemeral active regions and coronal bright points: A solar maximum Mission 2 guest investigator study

NASA Technical Reports Server (NTRS)

Harvey, K. L.; Tang, F. Y. C.; Gaizauskas, V.; Poland, A. I.

1986-01-01

A dominate association of coronal bright points (as seen in He wavelength 10830) was confirmed with the approach and subsequent disappearance of opposite polarity magnetic network. While coronal bright points do occur with ephemeral regions, this association is a factor of 2 to 4 less than with sites of disappearing magnetic flux. The intensity variations seen in He I wavelength 10830 are intermittent and often rapid, varying over the 3 minute time resolution of the data; their bright point counterparts in the C IV wavelength 1548 and 20 cm wavelength show similar, though not always coincident time variations. Ejecta are associated with about 1/3 of the dark points and are evident in the C IV and H alpha data. These results support the idea that the anti-correlation of X-ray bright points with the solar cycle can be explained by the correlation of these coronal emission structures with sites of cancelling flux, indicating that, in some cases, the process of magnetic flux removal results in the release of energy. That the intensity variations are rapid and variable suggests that this process works intermittently.

Bright points and ejections observed on the sun by the KORONAS-FOTON instrument TESIS

NASA Astrophysics Data System (ADS)

Ulyanov, A. S.; Bogachev, S. A.; Kuzin, S. V.

2010-10-01

Five-second observations of the solar corona carried out in the FeIX 171 Å line by the KORONAS-FOTON instrument TESIS are used to study the dynamics of small-scale coronal structures emitting in and around coronal bright points. The small-scale structures of the lower corona display complex dynamics similar to those of magnetic loops located at higher levels of the solar corona. Numerous detected oscillating structures with sizes below 10 000 km display oscillation periods from 50 to 350 s. The period distributions of these structures are different for P < 150 s and P > 150 s, which implies that different oscillation modes are excited at different periods. The small-scale structures generate numerous flare-like events with energies 1024-1026 erg (nanoflares) and with a spatial density of one event per arcsecond or more observed over an area of 4 × 1011 km2. Nanoflares are not associated with coronal bright points, and almost uniformly cover the solar disk in the observation region. The ejections of solar material from the coronal bright points demonstrate velocities of 80-110 km/s.

Ultraviolet Thomson Scattering from Direct-Drive Coronal Plasmas

NASA Astrophysics Data System (ADS)

Henchen, R. J.; Goncharov, V. N.; Michel, D. T.; Follett, R. K.; Katz, J.; Froula, D. H.

2013-10-01

Ultraviolet (λ4 ω = 263 nm) Thomson scattering (TS) was used to probe ion-acoustic waves (IAW's) and electron plasma waves (EPW's) from direct-drive coronal plasmas. Fifty-nine drive beams (λ3 ω = 351 nm) illuminate a spherical target with a radius of ~860 μm. Advances in the ultraviolet (UV) TS diagnostic at the Omega Laser Facility provide the ability to detect deep UV photons (~190 nm) and allow access to scattered light from EPW's propagating near the 3 ω quarter-critical surface (~2.5 × 1021 cm-3) . A series of experiments studied the effects of ablator materials on coronal plasma conditions. Electron temperatures and densities were measured from 150 μm to 400 μm from the initial target surface. Standard CH shells were compared to three-layered shells consisting of Si doped CH, Si, and Be. Early analysis indicates that these multilayered targets have less hot-electron energy as a result of higher electron temperature in the coronal plasma. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Effect of scaling and root planing on alveolar bone as measured by subtraction radiography.

PubMed

Hwang, You-Jeong; Fien, Matthew Jonas; Lee, Sam-Sun; Kim, Tae-Il; Seol, Yang-Jo; Lee, Yong-Moo; Ku, Young; Rhyu, In-Chul; Chung, Chong-Pyoung; Han, Soo-Boo

2008-09-01

Scaling and root planing of diseased periodontal pockets is fundamental to the treatment of periodontal disease. Although various clinical parameters have been used to assess the efficacy of this therapy, radiographic analysis of changes in bone density following scaling and root planing has not been extensively researched. In this study, digital subtraction radiography was used to analyze changes that occurred in the periodontal hard tissues following scaling and root planing. Thirteen subjects with a total of 39 sites that presented with >3 mm of vertical bone loss were included in this study. Clinical examinations were performed and radiographs were taken prior to treatment and were repeated 6 months following scaling and root planing. Radiographic analysis was performed with computer-assisted radiographic evaluation software. Three regions of interest (ROI) were defined as the most coronal, middle, and apical portions of each defect. A fourth ROI was used for each site as a control region and was placed at a distant, untreated area. Statistical analysis was carried out to evaluate changes in the mean gray level at the coronal, middle, and apical region of each treated defect. Digital subtraction radiography revealed an increase in radiographic density in 101 of the 117 test regions (83.3%). A 256 gray level was used, and a value >128 was assumed to represent a density gain in the ROI. The average gray level increase was 18.65. Although the coronal, middle, and apical regions displayed increases in bone density throughout this study, the bone density of the apical ROI (gray level = 151.27 +/- 20.62) increased significantly more than the bone density of the coronal ROI (gray level = 139.19 +/- 21.78). A significant increase in bone density was seen in probing depths >5 mm compared to those <5 mm in depth. No significant difference was found with regard to bone-density changes surrounding single- versus multiple-rooted teeth. Scaling and root planing of diseased periodontal pockets can significantly increase radiographic alveolar bone density as demonstrated through the use of digital subtraction radiography.

Time-resolved Spectroscopy of RS CVn Binaries and dMe Flare Stars

NASA Astrophysics Data System (ADS)

Brown, Alexander

One of the most striking feature of the first two years of EUVE spectroscopy is the frequent occurrence of largescale coronal variability, in the form of stellar flares and slower changes in activity level due to rotational modulation and evolution of active regions. We propose EUVE observations of a set of RS CVn and dMe star binaries, most with short (< 2 days) periods, to investigate the coronal conditions and physical processes associated with this variability. EUVE flare outbursts have mostly been long duration events lasting many satellite orbits and been readily studied using time-resolved spectroscopy. Our targets are the dMe binaries YY Gem, CC Eri and Gliese 2123, and the RS CVn systems EI Eri, AR Psc, and TY Pyx. YY Gem and TY Pyx are eclipsing systems and Deep Survey photometry will be used to investigate the size of the coronal emitting regions. Situated 73 arcmin from YY Gem is Castor (Alpha Gem) another X-ray source that can be observed (and spatially resolved) simultaneously. We shall use the DS lightcurve to guide our time resolved spectral analysis. Changes in the coronal emission measure as a function of temperature and possibly changes in coronal density will be used to constrain magnetic loop models.

Characteristics of coronal shock waves and solar type 2 radio bursts

NASA Technical Reports Server (NTRS)

Mann, G.; Classen, H.-T.

1995-01-01

In the solar corona shock waves generated by flares and/or coronal mass ejections can be observed by radio astronomical methods in terms of solar type 2 radio bursts. In dynamic radio spectra they appear as emission stripes slowly drifting from high to low frequencies. A sample of 25 solar type 2 radio bursts observed in the range of 40 - 170 MHz with a time resolution of 0.1 s by the new radiospectrograph of the Astrophvsikalisches Institut Potsdam in Tremsdorf is statistically investigated concerning their spectral features, i.e, drift rate, instantaneous bandwidth, and fundamental harmonic ratio. In-situ plasma wave measurements at interplanetary shocks provide the assumption that type 2 radio radiation is emitted in the vicinity of the transition region of shock waves. Thus, the instantaneous bandwidth of a solar type 2 radio burst would reflect the density jump across the associated shock wave. Comparing the inspection of the Rankine-Hugoniot relations of shock waves under coronal circumstances with those obtained from the observational study, solar type 2 radio bursts should be regarded to be generated by weak supercritical, quasi-parallel, fast magnetosonic shock waves in the corona.

Relationship between coronal holes and high speed streams at L1: arrival times, durations, and intensities

NASA Astrophysics Data System (ADS)

Luo, B.; Bu, X.; Liu, S.; Gong, J.

2017-12-01

Coronal holes are sources of high-speed steams (HSS) of solar wind. When coronal holes appear at mid/low latitudes on the Sun, consequential HSSs may impact Earth and cause recurrent geospace environment disturbances, such as geomagnetic storms, relativistic electron enhancements at the geosynchronous orbit, and thermosphere density enhancements. Thus, it is of interests for space weather forecasters to predict when (arrival times), how long (time durations), and how severe (intensities) HSSs may impact Earth when they notice coronal holes on the sun and are anticipating their geoeffectiveness. In this study, relationship between coronal holes and high speed streams will be statistically investigated. Several coronal hole parameters, including passage times of solar central meridian, coronal hole longitudinal widths, intensities reflected by mean brightness, are derived using Solar Dynamics Observatory (SDO)/Atmospheric Imaging Assembly (AIA) images for years 2011 to 2016. These parameters will be correlated with in-situ solar wind measurements measured at the L1 point by the ACE spacecraft, which can give some results that are useful for space weather forecaster in predicting the arrival times, durations, and intensities of coronal hole high-speed streams in about 3 days advance.

Recent VLA Measurements of CME-Induced Faraday Rotation

NASA Astrophysics Data System (ADS)

Kooi, Jason; Thomas, Najma; Guy, Michael; Spangler, Steven R.

2018-01-01

Observations of Faraday rotation, the change in polarization position angle of linearly polarized radiation as it propagates through a magnetized plasma, have been used for decades to determine the strength and structure of the coronal magnetic field and plasma density. Similarly, observations of Faraday rotation through a coronal mass ejection (CME) have the potential to improve our understanding of the CME’s plasma structure. We report recent results from simultaneous white-light coronagraph and radio observations made of a CME in July 2015. We made radio observations using the Karl G. Jansky Very Large Array (VLA) at 1 - 2 GHz frequencies of a set of cosmic radio sources through the solar corona at heliocentric distances that ranged between 8 - 23 solar radii. A unique aspect of these observations is that the CME occulted several of these radio sources and, therefore, our Faraday rotation measurements provide information on the plasma structure in different regions of the CME. We successfully measured CME-induced Faraday rotation along multiple lines of sight because we made special arrangements with the staff at the National Radio Astronomy Observatory to trigger VLA observations when a candidate CME appeared low in the corona in near real-time images from the Large Angle and Spectrometric Coronagraph (LASCO) C2 instrument.

Evaluating Uncertainties in Coronal Electron Temperature and Radial Speed Measurements Using a Simulation of the Bastille Day Eruption

NASA Astrophysics Data System (ADS)

Reginald, Nelson; St. Cyr, Orville; Davila, Joseph; Rastaetter, Lutz; Török, Tibor

2018-05-01

Obtaining reliable measurements of plasma parameters in the Sun's corona remains an important challenge for solar physics. We previously presented a method for producing maps of electron temperature and speed of the solar corona using K-corona brightness measurements made through four color filters in visible light, which were tested for their accuracies using models of a structured, yet steady corona. In this article we test the same technique using a coronal model of the Bastille Day (14 July 2000) coronal mass ejection, which also contains quiet areas and streamers. We use the coronal electron density, temperature, and flow speed contained in the model to determine two K-coronal brightness ratios at (410.3, 390.0 nm) and (423.3, 398.7 nm) along more than 4000 lines of sight. Now assuming that for real observations, the only information we have for each line of sight are these two K-coronal brightness ratios, we use a spherically symmetric model of the corona that contains no structures to interpret these two ratios for electron temperature and speed. We then compare the interpreted (or measured) values for each line of sight with the true values from the model at the plane of the sky for that same line of sight to determine the magnitude of the errors. We show that the measured values closely match the true values in quiet areas. However, in locations of coronal structures, the measured values are predictably underestimated or overestimated compared to the true values, but can nevertheless be used to determine the positions of the structures with respect to the plane of the sky, in front or behind. Based on our results, we propose that future white-light coronagraphs be equipped to image the corona using four color filters in order to routinely create coronal maps of electron density, temperature, and flow speed.

Diagnosing the Prominence-Cavity Connection in the Solar Corona

NASA Astrophysics Data System (ADS)

Schmit, D. J.

The energetic equilibrium of the corona is described by a balance of heating, thermal conduction, and radiative cooling. Prominences can be described by the thermal instability of coronal energy balance which leads to the formation of cool condensations. Observationally, the prominence is surrounded by a density depleted elliptical structure known as a cavity. In this dissertation, we use extreme ultraviolet remote sensing observations of the prominence-cavity system to diagnose the static and dynamic properties of these structures. The observations are compared with numerical models for the time-dependent coronal condensation process and the time-independent corona-prominence magnetic field. To diagnose the density of the cavity, we construct a three-dimensional structural model of the corona. This structural model allows us to synthesize extreme ultraviolet emission in the corona in a way that incorporates the projection effects which arise from the optically thin plasma. This forward model technique is used to constrain a radial density profile simultaneously in the cavity and the streamer. We use a χ2 minimization to find the density model which best matches a density sensitive line ratio (observed with Hinode/Extreme ultraviolet Imaging Spectrometer) and the white light scattered intensity (observed with Mauna Loa Solar Observatory MK4 coronagraph). We use extreme ultraviolet spectra and spectral images to diagnose the dynamics of the prominence and the surrounding corona. Based on the doppler shift of extreme ultraviolet coronal emission lines, we find that there are large regions of flowing plasma which appear to occur within cavities. These line of sight flows have speeds of 10 km/s-1 and projected spatial scales of 100 Mm. Using the Solar Dynamics Observatory Atmospheric Imaging Assembly (SDO/AIA) dataset, we observe dynamic emission from the prominence-cavity system. The SDO/AIA dataset observes multiple spectral bandpasses with different temperature sensitivities. Time-dependent changes in the observed emission in these bandpass images represent changes in the thermodynamic properties of the emitting plasma. We find that the coronal region surrounding the prominence exhibits larger intensity variations (over tens of hours of observations) as compared to the streamer region. This variability is particularly strong in the cool coronal emission of the 171Å bandpass. We identify the source of this variability as strong brightening events that resemble concave-up loop segments and extend from the cool prominence plasma. Magnetic field lines are the basic structural building block of the corona. Energy and pressure balance in the corona occur along magnetic field lines. The large-scale extreme ultraviolet emission we observe in the corona is a conglomerate of many coronal loops projected along a line of sight. In order to calculate the plasma properties at a particular point in the corona, we use one-dimensional models for energy and pressure balance along field lines. In order to predict the extreme ultraviolet emission along a particular line of sight, we project these one-dimensional models onto the three-dimensional magnetic configuration provided by a MHD model for the coronal magnetic field. These results have allowed us to the establish the first comprehensive picture on the magnetic and energetic interaction of the prominence and the cavity. While the originally hypothesis that the cavity supplies mass to the prominence proved inaccurate, we cannot simply say that these structures are not related. Rather our findings suggest that the prominence and the cavity are distinct magnetic substructures that are complementary regions of a larger whole, specifically a magnetic flux rope. (Abstract shortened by UMI.).

Constraints on CME Evolution from in situ Observations of Ionic Charge States

NASA Technical Reports Server (NTRS)

Gruesbeck, Jacob R.; Lepri, Susan T.; Zurbuchen, Thomas H.; Antiochos, Spiro K.

2010-01-01

We present a novel procedure for deriving the physical properties of Coronal Mass Ejections (CMES) in the corona. Our methodology uses in-situ measurements of ionic charge states of C, O, Si and Fe in the heliosphere and interprets them in the context of a model for the early evolution of ICME plasma, between 2 - 5 R-solar. We find that the data can be fit only by an evolution that consists of an initial heating of the plasma, followed by an expansion that ultimately results in cooling. The heating profile is consistent with a compression of coronal plasma due to flare reconnect ion jets and an expansion cooling due to the ejection, as expected from the standard CME/flare model. The observed frozen-in ionic charge states reflect this time-history and, therefore, provide important constraints for the heating and expansion time-scales, as well as the maximum temperature the CME plasma is heated to during its eruption. Furthermore, our analysis places severe limits on the possible density of CME plasma in the corona. We discuss the implications of our results for CME models and for future analysis of ICME plasma composition.

Flow properties of the solar wind obtained from white light data and a two-fluid model

NASA Technical Reports Server (NTRS)

Habbal, Shadia Rifai; Esser, Ruth; Guhathakurta, Madhulika; Fisher, Richard

1994-01-01

The flow properties of the solar wind from 1 R(sub s) to 1 AU were obtained using a two fluid model constrained by density and scale height temperatures derived from white light observations, as well as knowledge of the electron temperature in coronal holes. The observations were obtained with the white light coronographs on SPARTAN 201-1 and at Mauna Loa (Hawaii), in a north polar coronal hole from 1.16 to 5.5 R(sub s) on 11 Apr. 1993. By specifying the density, temperature, Alfven wave velocity amplitude and heating function at the coronal base, it was found that the model parameters fit well the constraints of the empirical density profiles and temperatures. The optimal range of the input parameters was found to yield a higher proton temperature than electron temperature in the inner corona. The results indicate that no preferential heating of the protons at larger distances is needed to produce higher proton than electron temperatures at 1 AU, as observed in the high speed solar wind.

Modelling coronal electron density and temperature profiles of the Active Region NOAA 11855

NASA Astrophysics Data System (ADS)

Rodríguez Gómez, J. M.; Antunes Vieira, L. E.; Dal Lago, A.; Palacios, J.; Balmaceda, L. A.; Stekel, T.

2017-10-01

The magnetic flux emergence can help understand the physical mechanism responsible for solar atmospheric phenomena. Emerging magnetic flux is frequently related to eruptive events, because when emerging they can reconnected with the ambient field and release magnetic energy. We will use a physic-based model to reconstruct the evolution of the solar emission based on the configuration of the photospheric magnetic field. The structure of the coronal magnetic field is estimated by employing force-free extrapolation NLFFF based on vector magnetic field products (SHARPS) observed by HMI instrument aboard SDO spacecraft from Sept. 29 (2013) to Oct. 07 (2013). The coronal plasma temperature and density are described and the emission is estimated using the CHIANTI atomic database 8.0. The performance of the our model is compared to the integrated emission from the AIA instrument aboard SDO spacecraft in the specific wavelengths 171Å and 304Å.

Observation of a reversal of rotation in a sunspot during a solar flare

PubMed Central

Bi, Yi; Jiang, Yunchun; Yang, Jiayan; Hong, Junchao; Li, Haidong; Yang, Bo; Xu, Zhe

2016-01-01

The abrupt motion of the photospheric flux during a solar flare is thought to be a back reaction caused by the coronal field reconfiguration. However, the type of motion pattern and the physical mechanism responsible for the back reaction has been uncertain. Here we show that the direction of a sunspot's rotation is reversed during an X1.6 flare using observations from the Helioseismic and Magnetic Imager. A magnetic field extrapolation model shows that the corresponding coronal magnetic field shrinks with increasing magnetic twist density. This suggests that the abrupt reversal of rotation in the sunspot may be driven by a Lorentz torque that is produced by the gradient of twist density from the solar corona to the solar interior. These results support the view that the abrupt reversal in the rotation of the sunspot is a dynamic process responding to shrinkage of the coronal magnetic field during the flare. PMID:27958266

Ultra-fine-scale filamentary structures in the Outer Corona and the Solar Magnetic Field

NASA Technical Reports Server (NTRS)

Woo, Richard

2006-01-01

Filamentary structures following magnetic field lines pervade the Sun's atmosphere and offer us insight into the solar magnetic field. Radio propagation measurements have shown that the smallest filamentary structures in the solar corona are more than 2 orders of magnitude finer than those seen in solar imaging. Here we use radio Doppler measurements to characterize their transverse density gradient and determine their finest scale in the outer corona at 20-30 R(circled dot operator), where open magnetic fields prevail. Filamentary structures overly active regions have the steepest gradient and finest scale, while those overlying coronal holes have the shallowest gradient and least finest scale. Their organization by the underlying corona implies that these subresolution structures extend radially from the entire Sun, confirming that they trace the coronal magnetic field responsible for the radial expansion of the solar wind. That they are rooted all over the Sun elucidates the association between the magnetic field of the photosphere and that of the corona, as revealed by the similarity between the power spectra of the photospheric field and the coronal density fluctuations. This association along with the persistence of filamentary structures far from the Sun demonstrate that subresolution magnetic fields must play an important role not only in magnetic coupling of the photosphere and corona, but also in coronal heating and solar wind acceleration through the process of small-scale magnetic reconnection. They also explain why current widely used theoretical models that extrapolate photospheric magnetic fields into the corona do not predict the correct source of the solar wind.

Lifecycle of a large-scale polar coronal pseudostreamer/cavity system

NASA Astrophysics Data System (ADS)

Guennou, Chloé; Auchere, Frederic; Seaton, Daniel; Rachmeler, Laurel

2016-07-01

Coronal cavities, tunnel-like areas of rarefied density, provide important information about the magnetic structures that support prominences. The magnetic energy is stored through the twisted or shared magnetic field, ultimately released through Coronal Mass Ejections (CME). To be able to forecast these energetic releases of material and prevent potential terrestrial consequences, the understanding of the cavity 3D morphology, magnetic and thermal properties are essential. The prominences embedded in the cavity only trace a small part of the magnetic field, whereas the much larger cavity provides more information about the magnetic field morphology. As a result, a clear understanding of the coronal volume of the cavity significantly advances our understanding of both the pre-eruption equilibrium and the triggers of such eruptions. Determining both morphological and thermodynamical coronal structures is difficult due to the optically thin nature of the plasma. Observations are subject to integration along the line-of-sight (LOS). This effect can strongly complicate both the derivation and the interpretation of important physical quantities. One way to deduce the 3D structure is with Solar Rotational Tomography (SRT). The 3D plasma emissivity is estimated from EUV/white light images taken from different viewpoints. Physical properties can be then derived using Differential Emission Measure analysis from multi-wavelength 3D reconstructions. We applied this technique to an exceptional large-scale coronal pseudostreamer/cavity system in the southern polar region of the solar corona that was visible for approximately a year starting in February 2014. It is unusual to see such a large closed-field structure embedded within the open polar coronal hole. We investigate this structure to document its formation, evolution and eventually its shrinking process using data from both the PROBA2/SWAP and SDO/AIA EUV imagers. We found that the cavity temperature is extremely stable with time and is essentially at a similar or slightly hotter temperature than the surrounding pseudostreamer. Two regimes in cavity thermal properties were observed: during the first 5 months of observation, we found lower density depletion and highly multi-thermal plasma, while after the pseudostreamer became stable and slowly shrank, the depletion was more pronounced and the plasma was less multithermal. As the thermodynamic properties are strongly correlated with the magnetic structure, these results provide constraints on both the trigger of CMEs and the processes that maintain cavities stability for such a long lifetime.

LOFAR observations of the quiet solar corona

NASA Astrophysics Data System (ADS)

Vocks, C.; Mann, G.; Breitling, F.; Bisi, M. M.; Dąbrowski, B.; Fallows, R.; Gallagher, P. T.; Krankowski, A.; Magdalenić, J.; Marqué, C.; Morosan, D.; Rucker, H.

2018-06-01

Context. The quiet solar corona emits meter-wave thermal bremsstrahlung. Coronal radio emission can only propagate above that radius, Rω, where the local plasma frequency equals the observing frequency. The radio interferometer LOw Frequency ARray (LOFAR) observes in its low band (10-90 MHz) solar radio emission originating from the middle and upper corona. Aims: We present the first solar aperture synthesis imaging observations in the low band of LOFAR in 12 frequencies each separated by 5 MHz. From each of these radio maps we infer Rω, and a scale height temperature, T. These results can be combined into coronal density and temperature profiles. Methods: We derived radial intensity profiles from the radio images. We focus on polar directions with simpler, radial magnetic field structure. Intensity profiles were modeled by ray-tracing simulations, following wave paths through the refractive solar corona, and including free-free emission and absorption. We fitted model profiles to observations with Rω and T as fitting parameters. Results: In the low corona, Rω < 1.5 solar radii, we find high scale height temperatures up to 2.2 × 106 K, much more than the brightness temperatures usually found there. But if all Rω values are combined into a density profile, this profile can be fitted by a hydrostatic model with the same temperature, thereby confirming this with two independent methods. The density profile deviates from the hydrostatic model above 1.5 solar radii, indicating the transition into the solar wind. Conclusions: These results demonstrate what information can be gleaned from solar low-frequency radio images. The scale height temperatures we find are not only higher than brightness temperatures, but also than temperatures derived from coronograph or extreme ultraviolet (EUV) data. Future observations will provide continuous frequency coverage. This continuous coverage eliminates the need for local hydrostatic density models in the data analysis and enables the analysis of more complex coronal structures such as those with closed magnetic fields.

Brightness and magnetic evolution of solar coronal bright points

NASA Astrophysics Data System (ADS)

Ugarte Urra, Ignacio

This thesis presents a study of the brightness and magnetic evolution of several Extreme ultraviolet (EUV) coronal bright points (hereafter BPs). The study was carried out using several instruments on board the Solar and Heliospheric Observatory, supported by the high resolution imaging from the Transition Region And Coronal Explorer. The results confirm that, down to 1" resolution, BPs are made of small loops with lengths of [approximate]6 Mm and cross-sections of ≈2 Mm. The loops are very dynamic, evolving in time scales as short as 1 - 2 minutes. This is reflected in a highly variable EUV response with fluctuations highly correlated in spectral lines at transition region temperatures, but not always at coronal temperatures. A wavelet analysis of the intensity variations reveals the existence of quasi-periodic oscillations with periods ranging 400--1000s, in the range of periods characteristic of the chromospheric network. The link between BPs and network bright points is discussed, as well as the interpretation of the oscillations in terms of global acoustic modes of closed magnetic structures. A comparison of the magnetic flux evolution of the magnetic polarities to the EUV flux changes is also presented. Throughout their lifetime, the intrinsic EUV emission of BPs is found to be dependent on the total magnetic flux of the polarities. In short time scales, co-spatial and co-temporal coronal images and magnetograms, reveal the signature of heating events that produce sudden EUV brightenings simultaneous to magnetic flux cancellations. This is interpreted in terms of magnetic reconnection events. Finally, a electron density study of six coronal bright points produces values of ≈1.6×10 9 cm -3 , closer to active region plasma than to quiet Sun. The analysis of a large coronal loop (half length of 72 Mm) introduces the discussion on the prospects of future plasma diagnostics of BPs with forthcoming solar missions.

OBSERVATIONAL SIGNATURES OF CORONAL LOOP HEATING AND COOLING DRIVEN BY FOOTPOINT SHUFFLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahlburg, R. B.; Taylor, B. D.; Einaudi, G.

The evolution of a coronal loop is studied by means of numerical simulations of the fully compressible three-dimensional magnetohydrodynamic equations using the HYPERION code. The footpoints of the loop magnetic field are advected by random motions. As a consequence, the magnetic field in the loop is energized and develops turbulent nonlinear dynamics characterized by the continuous formation and dissipation of field-aligned current sheets: energy is deposited at small scales where heating occurs. Dissipation is nonuniformly distributed so that only a fraction of the coronal mass and volume gets heated at any time. Temperature and density are highly structured at scalesmore » that, in the solar corona, remain observationally unresolved: the plasma of our simulated loop is multithermal, where highly dynamical hotter and cooler plasma strands are scattered throughout the loop at sub-observational scales. Numerical simulations of coronal loops of 50,000 km length and axial magnetic field intensities ranging from 0.01 to 0.04 T are presented. To connect these simulations to observations, we use the computed number densities and temperatures to synthesize the intensities expected in emission lines typically observed with the Extreme Ultraviolet Imaging Spectrometer on Hinode. These intensities are used to compute differential emission measure distributions using the Monte Carlo Markov Chain code, which are very similar to those derived from observations of solar active regions. We conclude that coronal heating is found to be strongly intermittent in space and time, with only small portions of the coronal loop being heated: in fact, at any given time, most of the corona is cooling down.« less

Magnetic Untwisting in Jets that Go into the Outer Solar Corona in Polar Coronal Holes

NASA Astrophysics Data System (ADS)

Moore, Ronald L.; Sterling, Alphonse C.; Falconer, David

2014-06-01

We present results from a study of 14 jets that were observed in SDO/AIA EUV movies to erupt in the Sun’s polar coronal holes. These jets were similar to the many other jets that erupt in coronal holes, but reached higher than the vast majority, high enough to be observed in the outer corona beyond 2 solar radii from Sun center by the SOHO/LASCO/C2 coronagraph. We illustrate the characteristic structure and motion of these high-reaching jets by showing observations of two representative jets. We find that (1) the speed of the jet front from the base of the corona out to 2-3 solar radii is typically several times the sound speed in jets in coronal holes, (2) each high-reaching jet displays unusually large rotation about its axis (spin) as it erupts, and (3) in the outer corona, many jets display lateral swaying and bending of the jet axis with an amplitude of a few degrees and a period of order 1 hour. From these observations we infer that these jets are magnetically driven, propose that the driver is a magnetic-untwisting wave that is basically a large-amplitude (non-linear) torsional Alfven wave that is put into the open magnetic field in the jet by interchange reconnection as the jet erupts, and estimate that the magnetic-untwisting wave loses most of its energy before reaching the outer corona. These observations of high-reaching coronal jets suggest that the torsional magnetic waves observed in Type-II spicules can similarly dissipate in the corona and thereby power much of the coronal heating in coronal holes and quiet regions. This work is funded by the NASA/SMD Heliophysics Division’s Living With a Star Targeted Research & Technology Program.

The density compression ratio of shock fronts associated with coronal mass ejections

NASA Astrophysics Data System (ADS)

Kwon, Ryun-Young; Vourlidas, Angelos

2018-02-01

We present a new method to extract the three-dimensional electron density profile and density compression ratio of shock fronts associated with coronal mass ejections (CMEs) observed in white light coronagraph images. We demonstrate the method with two examples of fast halo CMEs (˜2000 km s-1) observed on 2011 March 7 and 2014 February 25. Our method uses the ellipsoid model to derive the three-dimensional geometry and kinematics of the fronts. The density profiles of the sheaths are modeled with double-Gaussian functions with four free parameters, and the electrons are distributed within thin shells behind the front. The modeled densities are integrated along the lines of sight to be compared with the observed brightness in COR2-A, and a χ2 approach is used to obtain the optimal parameters for the Gaussian profiles. The upstream densities are obtained from both the inversion of the brightness in a pre-event image and an empirical model. Then the density ratio and Alfvénic Mach number are derived. We find that the density compression peaks around the CME nose, and decreases at larger position angles. The behavior is consistent with a driven shock at the nose and a freely propagating shock wave at the CME flanks. Interestingly, we find that the supercritical region extends over a large area of the shock and lasts longer (several tens of minutes) than past reports. It follows that CME shocks are capable of accelerating energetic particles in the corona over extended spatial and temporal scales and are likely responsible for the wide longitudinal distribution of these particles in the inner heliosphere. Our results also demonstrate the power of multi-viewpoint coronagraphic observations and forward modeling in remotely deriving key shock properties in an otherwise inaccessible regime.

On the derivation of empirical limits on the helium abundance in coronal holes below 1.5 solar radius

NASA Technical Reports Server (NTRS)

Habbal, Shadia Rifai; Esser, Ruth

1994-01-01

We present a simple technique describing how limits on the helium abundance, alpha, defined as the ratio of helium to proton number density, can be inferred from measurements of the electron density and temperature below 1.5 solar radius. As an illustration, we apply this technique to two different data sets: emission-line intensities in the extreme ultraviolet (EUV) and white-light observations, both measured in polar coronal holes. For the EUV data, the temperature gradient is derived from line intensity ratios, and the density gradient is replaced by the gradient of the line intensity. The lower limit on alpha derived from these data is 0.2-0.3 at 1 solar radius and drops very sharply to interplanetary values of a few percent below 1.06 solar radius. The white-light observations yield density gradients in the inner corona beyond 1.25 solar radius but do not have corresponding temperature gradients. In this case we consider an isothermal atmosphere, and derive an upper limit of 0.2 for alpha. These examples are used to illustrate how this technique could be applicable to the more extensive data to be obtained with the upcoming SOHO mission. Although only ranges on alpha can be derived, the application of the technique to data currently available merely points to the fact that alpha can be significantly large in the inner corona.

The coronal electron density distribution determined from dual-frequency ranging measurements during the 1991 solar conjunction of the Ulysses spacecraft

NASA Technical Reports Server (NTRS)

Bird, M. K.; Volland, H.; Paetzold, M.; Edenhofer, P.; Asmar, S. W.; Brenkle, J. P.

1994-01-01

Dual-frequency ranging and Doppler measurements were conducted in support of the Ulysses Solar Corona Experiment (SCE) at and around the spacecraft's first solar conjunction in 1991 August. The differential group delay time between range codes on the two downlink carrier signals at the wavelengths 13.1 and 3.6 cm, a direct measure of the total electron content between spacecraft and ground station, was used to derive the electron density distribution in the solar corona. Linear power-law representations of the coronal electron density were derived for the range of solar distances from 4 solar radii to 40 solar radii on both sides of the Sun. The corona was found to be very nearly symmetric; the radial falloff exponent being 2.54 +/- 0.05 for occultation ingress (east solar limb) and 2.42 +/- 0.05 for egress (west limb), respectively. The departure of these exponents from the inverse equare relation implies that significant solar wind acceleration is occurring within the radial range of the observations. The electron density level was found to be considerably lower than that observed during the 1988 December solar occultation of Voyager 2. Although the smoothed sunspot number R(sub z) (a standard indicator of solar activity) was almost the same in 1988 December and 1991 August, the mean electron density at 20 solar radii was found to be 1.7 +/- 0.1 x 10(exp 3)/cu cm during the Ulysses conjunction, a decline by almost a factor of 4 from the value obtained during the Voyager conjunction.

Coronal Magnetography of Solar Active Regions Using Coordinated SOHO/CDS and VLA Observations

NASA Technical Reports Server (NTRS)

Brosius, Jeffrey W.

1999-01-01

The purpose of this project is to apply the coronal magnetographic technique to SOHO (Solar Heliospheric Observatory) /CDS (Coronal Diagnostic Spectrometer) EUV (Extreme Ultraviolet Radiation) and coordinated VLA microwave observations of solar active regions to derive the strength and structure of the coronal magnetic field. A CDS observing plan was developed for obtaining spectra needed to derive active region differential emission measures (DEMs) required for coronal magnetography. VLA observations were proposed and obtained. SOHO JOP 100 was developed, tested, approved, and implemented to obtain coordinated CDS (Coronal Diagnostic Spectrometer)/EIT (Ultraviolet Imaging Telescope)/ VLA (Very Large Array)/ TRACE (Transition Region and Coronal Explorer)/ SXT (Solar X Ray Telescope) observations of active regions on April 12, May 9, May 13, and May 23. Analysis of all four data sets began, with heaviest concentration on COS data. It is found that 200-pixel (14 A in NIS1) wavelength windows are appropriate for extracting broadened Gaussian line profile fit parameters for lines including Fe XIV at 334.2, Fe XVI at 335.4, Fe XVI at 360.8, and Mg IX at 368.1 over the 4 arcmin by 4 arcmin CDS field of view. Extensive efforts were focused on learning and applying were focused on learning and applying CDS software, and including it in new IDL procedures to carry out calculations relating to coronal magnetography. An important step is to extract Gaussian profile fits to all the lines needed to derive the DEM in each spatial pixel of any given active region. The standard CDS absolute intensity calibration software was applied to derived intensity images, revealing that ratios between density-insensitive lines like Fe XVI 360.8/335.4 yield good agreement with theory. However, the resulting absolute intensities of those lines are very high, indicating that revisions to the CDS absolute intensity calibrations remain to be included in the CDS software, an essential step to deriving reliable coronal magnetograms. With lessons learned and high quality data obtained during the past year, coronal magnetography will be successfully pursued under my new SOHO GI program.

Automatic detection and quantitative analysis of cells in the mouse primary motor cortex

NASA Astrophysics Data System (ADS)

Meng, Yunlong; He, Yong; Wu, Jingpeng; Chen, Shangbin; Li, Anan; Gong, Hui

2014-09-01

Neuronal cells play very important role on metabolism regulation and mechanism control, so cell number is a fundamental determinant of brain function. Combined suitable cell-labeling approaches with recently proposed three-dimensional optical imaging techniques, whole mouse brain coronal sections can be acquired with 1-μm voxel resolution. We have developed a completely automatic pipeline to perform cell centroids detection, and provided three-dimensional quantitative information of cells in the primary motor cortex of C57BL/6 mouse. It involves four principal steps: i) preprocessing; ii) image binarization; iii) cell centroids extraction and contour segmentation; iv) laminar density estimation. Investigations on the presented method reveal promising detection accuracy in terms of recall and precision, with average recall rate 92.1% and average precision rate 86.2%. We also analyze laminar density distribution of cells from pial surface to corpus callosum from the output vectorizations of detected cell centroids in mouse primary motor cortex, and find significant cellular density distribution variations in different layers. This automatic cell centroids detection approach will be beneficial for fast cell-counting and accurate density estimation, as time-consuming and error-prone manual identification is avoided.

Coronal Loop Evolution Observed with AIA and Hi-C

NASA Technical Reports Server (NTRS)

Mulu-Moore, Fana; Winebarger, A.; Cirtain, J.; Kobayashi, K.; Korreck, K.; Golub, L.; Kuzin. S.; Walsh, R.; DeForest, C.; DePontieu, B.;

A New View of the Origin of the Solar Wind

NASA Technical Reports Server (NTRS)

Woo, Richard; Habbal, Shadia Rifai

1999-01-01

This paper uses white-light measurements made by the SOHO LASCO coronagraph and HAO Mauna Loa Mk III K-coronameter to illustrate the new view of solar wind structure deduced originally from radio occultation measurements. It is shown that the density profile closest to the Sun at 1.15 Ro, representing the imprint of the Sun, is carried essentially radially into interplanetary space by small-scale raylike structures that permeate the solar corona and which have only been observed by radio occultation measurements. The only exception is the small volume of interplanetary space occupied by the heliospheric plasma sheet that evolves from coronal streamers within a few solar radii of the Sun. The radial preservation of the density profile also implies that a significant fraction of field lines which extend into interplanetary space originate from the quiet Sun, and are indistinguishable in character from those emanating from polar coronal holes. The white-light measurements dispel the long-held belief that the boundaries of polar coronal holes diverge significantly, and further support the view originally proposed that the fast solar wind originates from the quiet Sun as well as polar coronal holes.

Unresolved fine-scale structure in solar coronal loop-tops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scullion, E.; Van der Voort, L. Rouppe; Wedemeyer, S.

2014-12-10

New and advanced space-based observing facilities continue to lower the resolution limit and detect solar coronal loops in greater detail. We continue to discover even finer substructures within coronal loop cross-sections, in order to understand the nature of the solar corona. Here, we push this lower limit further to search for the finest coronal loop substructures, through taking advantage of the resolving power of the Swedish 1 m Solar Telescope/CRisp Imaging Spectro-Polarimeter (CRISP), together with co-observations from the Solar Dynamics Observatory/Atmospheric Image Assembly (AIA). High-resolution imaging of the chromospheric Hα 656.28 nm spectral line core and wings can, under certainmore » circumstances, allow one to deduce the topology of the local magnetic environment of the solar atmosphere where its observed. Here, we study post-flare coronal loops, which become filled with evaporated chromosphere that rapidly condenses into chromospheric clumps of plasma (detectable in Hα) known as a coronal rain, to investigate their fine-scale structure. We identify, through analysis of three data sets, large-scale catastrophic cooling in coronal loop-tops and the existence of multi-thermal, multi-stranded substructures. Many cool strands even extend fully intact from loop-top to footpoint. We discover that coronal loop fine-scale strands can appear bunched with as many as eight parallel strands within an AIA coronal loop cross-section. The strand number density versus cross-sectional width distribution, as detected by CRISP within AIA-defined coronal loops, most likely peaks at well below 100 km, and currently, 69% of the substructure strands are statistically unresolved in AIA coronal loops.« less

Explosive plasma flows in a solar flare

NASA Technical Reports Server (NTRS)

Zarro, Dominic M.; Canfield, Richard C.; Metcalf, Thomas R.; Strong, Keith T.

1988-01-01

Solar Maximum Mission soft X-ray data and Sacramento Peak Observatory H-alpha observations are combined in a study of the impulsive phase of a solar flare. A blue asymmetry, indicative of upflows, was observed in the coronal Ca XIX line during the soft X-ray rise phase. A red asymmetry, indicative of downflows, was observed simultaneously in chromospheric H-alpha emitted from bright flare kernels during the period of hard X-ray emission. Combining the velocity data with a measurement of coronal electron density, it is shown that the impulsive phase momentum of upflowing soft X-ray-emitting plasma equalled that of the downflowing H-alpha-emitting plasma to within one order of magnitude. In particular, the momentum of the upflowing plasma was 2 x 10 to the 21st g cm/s while that of the downflowing plasma was 7 x 10 to the 21st g cm/s, with a factor of 2 uncertainty on each value. This equality supports the explosive chromospheric evaporation model of solar flares, in which a sudden pressure increase at the footprint of a coronal loop produces oppositely directed flows in the heated plasma.

On the theory of coronal heating mechanisms

NASA Technical Reports Server (NTRS)

Kuperus, M.; Ionson, J. A.; Spicer, D. S.

1980-01-01

Theoretical models describing solar coronal heating mechanisms are reviewed in some detail. The requirements of chromospheric and coronal heating are discussed in the context of the fundamental constraints encountered in modelling the outer solar atmosphere. Heating by acoustic processes in the 'nonmagnetic' parts of the atmosphere is examined with particular emphasis on the shock wave theory. Also discussed are theories of heating by electrodynamic processes in the magnetic regions of the corona, either magnetohydrodynamic waves or current heating in the regions with large electric current densities (flare type heating). Problems associated with each of the models are addressed.

Investigation of the Large Scale Evolution and Topology of Coronal Mass Ejections in the Solar Wind

NASA Technical Reports Server (NTRS)

Riley, Peter

1999-01-01

This investigation is concerned with the large-scale evolution and topology of Coronal Mass Ejections (CMEs) in the solar wind. During this reporting period we have analyzed a series of low density intervals in the ACE (Advanced Composition Explorer) plasma data set that bear many similarities to CMEs. We have begun a series of 3D, MHD (Magnetohydrodynamics) coronal models to probe potential causes of these events. We also edited two manuscripts concerning the properties of CMEs in the solar wind. One was re-submitted to the Journal of Geophysical Research.

Investigating the ability of solar coronal shocks to accelerate solar energetic particles

NASA Astrophysics Data System (ADS)

Kwon, R. Y.; Vourlidas, A.

2017-12-01

We estimate the density compression ratio of shocks associated with coronal mass ejections (CMEs) and investigate whether they can accelerate solar energetic particles (SEPs). Using remote-sensing, multi-viewpoint coronagraphic observations, we have developed a method to extract the sheath electron density profiles along the shock normal and estimate the density compression ratio. Our method uses the ellipsoid model to derive the 3D geometry of the sheaths, including the line-of-sight (LOS) depth. The sheath density profiles along the shock normal are modeled with double-Gaussian functions, and the modeled densities are integrated along the LOSs to be compared with the observed brightness in STEREO COR2-Ahead. The upstream densities are derived from either the pB-inversion of the brightness in a pre-event image or an empirical model. We analyze two fast halo CMEs observed on 2011 March 7 and 2014 February 25 that are associated with SEP events detected by multiple spacecraft located over a broad range of heliolongitudes. We find that the density compression peaks around the CME nose and decreases at larger position angles. Interestingly, we find that the supercritical region extends over a large area of the shock and lasts longer (several tens of minutes) than past reports. This finding implies that CME shocks may be capable of accelerating energetic particles in the corona over extended spatial and temporal scales and may, therefore, be responsible for the wide longitudinal distribution of these particles in the inner heliosphere.

A Time-dependent Heliospheric Model Driven by Empirical Boundary Conditions

NASA Astrophysics Data System (ADS)

Kim, T. K.; Arge, C. N.; Pogorelov, N. V.

2017-12-01

Consisting of charged particles originating from the Sun, the solar wind carries the Sun's energy and magnetic field outward through interplanetary space. The solar wind is the predominant source of space weather events, and modeling the solar wind propagation to Earth is a critical component of space weather research. Solar wind models are typically separated into coronal and heliospheric parts to account for the different physical processes and scales characterizing each region. Coronal models are often coupled with heliospheric models to propagate the solar wind out to Earth's orbit and beyond. The Wang-Sheeley-Arge (WSA) model is a semi-empirical coronal model consisting of a potential field source surface model and a current sheet model that takes synoptic magnetograms as input to estimate the magnetic field and solar wind speed at any distance above the coronal region. The current version of the WSA model takes the Air Force Data Assimilative Photospheric Flux Transport (ADAPT) model as input to provide improved time-varying solutions for the ambient solar wind structure. When heliospheric MHD models are coupled with the WSA model, density and temperature at the inner boundary are treated as free parameters that are tuned to optimal values. For example, the WSA-ENLIL model prescribes density and temperature assuming momentum flux and thermal pressure balance across the inner boundary of the ENLIL heliospheric MHD model. We consider an alternative approach of prescribing density and temperature using empirical correlations derived from Ulysses and OMNI data. We use our own modeling software (Multi-scale Fluid-kinetic Simulation Suite) to drive a heliospheric MHD model with ADAPT-WSA input. The modeling results using the two different approaches of density and temperature prescription suggest that the use of empirical correlations may be a more straightforward, consistent method.

Coronal magnetic fields from multiple type II bursts

NASA Astrophysics Data System (ADS)

Honnappa, Vijayakumar; Raveesha, K. H.; Subramanian, K. R.

Coronal magnetic fields from multiple type II bursts Vijayakumar H Doddamani1*, Raveesha K H2 and Subramanian3 1Bangalore University, Bangalore, Karnataka state, India 2CMR Institute of Technology, Bangalore, Karnataka state, India 3 Retd, Indian Institute of Astrophysics, Bangalore, Karnataka state, India Abstract Magnetic fields play an important role in the astrophysical processes occurring in solar corona. In the solar atmosphere, magnetic field interacts with the plasma, producing abundant eruptive activities. They are considered to be the main factors for coronal heating, particle acceleration and the formation of structures like prominences, flares and Coronal Mass Ejections. The magnetic field in solar atmosphere in the range of 1.1-3 Rsun is especially important as an interface between the photospheric magnetic field and the solar wind. Its structure and time dependent change affects space weather by modifying solar wind conditions, Cho (2000). Type II doublet bursts can be used for the estimation of the strength of the magnetic field at two different heights. Two type II bursts occur sometimes in sequence. By relating the speed of the type II radio burst to Alfven Mach Number, the Alfven speed of the shock wave generating type II radio burst can be calculated. Using the relation between the Alfven speed and the mean frequency of emission, the magnetic field strength can be determined at a particular height. We have used the relative bandwidth and drift rate properties of multiple type II radio bursts to derive magnetic field strengths at two different heights and also the gradient of the magnetic field in the outer corona. The magnetic field strength has been derived for different density factors. It varied from 1.2 to 2.5 gauss at a solar height of 1.4 Rsun. The empirical relation of the variation of the magnetic field with height is found to be of the form B(R) = In the present case the power law index ‘γ’ varied from -3 to -2 for variation of density factor from 1 to 5. Key Words: Magnetic field, photosphere, corona, solar wind, bursts *Email:drvkdmani@gmail.com

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oliver, R.; Soler, R.; Terradas, J.

Observations of active regions and limb prominences often show cold, dense blobs descending with an acceleration smaller than that of free fall. The dynamics of these condensations falling in the solar corona is investigated in this paper using a simple fully ionized plasma model. We find that the presence of a heavy condensation gives rise to a dynamical rearrangement of the coronal pressure that results in the formation of a large pressure gradient that opposes gravity. Eventually this pressure gradient becomes so large that the blob acceleration vanishes or even points upward. Then, the blob descent is characterized by anmore » initial acceleration phase followed by an essentially constant velocity phase. These two stages can be identified in published time-distance diagrams of coronal rain events. Both the duration of the first stage and the velocity attained by the blob increase for larger values of the ratio of blob to coronal density, for larger blob mass, and for smaller coronal temperature. Dense blobs are characterized by a detectable density growth (up to 60% in our calculations) and by a steepening of the density in their lower part, that could lead to the formation of a shock. They also emit sound waves that could be detected as small intensity changes with periods of the order of 100 s and lasting between a few and about 10 periods. Finally, the curvature of falling paths with large radii is only relevant when a very dense blob falls along inclined magnetic field lines.« less

Brightness and magnetic evolution of solar coronal bright points

NASA Astrophysics Data System (ADS)

Ugarte-Urra, I.

2004-12-01

This thesis presents a study of the brightness and magnetic evolution of several Extreme ultraviolet (EUV) coronal bright points (hereafter BPs). BPs are loop-like features of enhanced emission in the coronal EUV and X-ray images of the Sun, that are associated to the interaction of opposite photospheric magnetic polarities with magnetic fluxes of ≈1018 - 1019 Mx. The study was carried out using several instruments on board the Solar and Heliospheric Observatory (SOHO): the Extreme Ultraviolet Imager (EIT), the Coronal Diagnostic Spectrometer (CDS) and the Michelson Doppler Imager (MDI), supported by the high resolution imaging from the Transition Region And Coronal Explorer (TRACE). The results confirm that, down to 1'' (i.e. ~715 km) resolution, BPs are made of small loops with lengths of ~6 Mm and cross-sections of ~2 Mm. The loops are very dynamic, evolving in time scales as short as 1 - 2 minutes. This is reflected in a highly variable EUV response with fluctuations highly correlated in spectral lines at transition region temperatures (in the range 3.2x10^4 - 3.5x10^5 K), but not always at coronal temperatures. A wavelet analysis of the intensity variations reveals, for the first time, the existence of quasi-periodic oscillations with periods ranging 400 -- 1000 s, in the range of periods characteristic of the chromospheric network. The link between BPs and network bright points is discussed, as well as the interpretation of the oscillations in terms of global acoustic modes of closed magnetic structures. A comparison of the magnetic flux evolution of the magnetic polarities to the EUV flux changes is also presented. Throughout their lifetime, the intrinsic EUV emission of BPs is found to be dependent on the total magnetic flux of the polarities. In short time scales, co-spatial and co-temporal TRACE and MDI images, reveal the signature of heating events that produce sudden EUV brightenings simultaneous to magnetic flux cancellations. This is interpreted in terms of magnetic reconnection events. Finally, a electron density study of six coronal bright points produces values of ~1.6x109 cm-3, closer to active region plasma than to quiet Sun. The analysis of a large coronal loop (half length of 72 Mm) introduces the discussion on the prospects of future plasma diagnostics of BPs with forthcoming solar missions like Solar-B.

Endogenous Magnetic Reconnection in Solar Coronal Loops

NASA Astrophysics Data System (ADS)

Asgari-Targhi, M.; Coppi, B.; Basu, B.; Fletcher, A.; Golub, L.

2017-12-01

We propose that a magneto-thermal reconnection process occurring in coronal loops be the source of the heating of the Solar Corona [1]. In the adopted model, magnetic reconnection is associated with electron temperature gradients, anisotropic electron temperature fluctuations and plasma current density gradients [2]. The input parameters for our theoretical model are derived from the most recent observations of the Solar Corona. In addition, the relevant (endogenous) collective modes can produce high energy particle populations. An endogenous reconnection process is defined as being driven by factors internal to the region where reconnection takes place. *Sponsored in part by the U.S. D.O.E. and the Kavli Foundation* [1] Beafume, P., Coppi, B. and Golub, L., (1992) Ap. J. 393, 396. [2] Coppi, B. and Basu, B. (2017) MIT-LNS Report HEP 17/01.

Identification of coronal sources of the solar wind from solar images in the EUV spectral range

NASA Astrophysics Data System (ADS)

Slemzin, V. A.; Shugai, Yu. S.

2015-01-01

Methods of localizing coronal sources of the solar wind (SW), such as coronal holes, quasi-stationary fluxes from active regions, and transient sources associated with small-scale active phenomena are considered based on vacuum-ultraviolet (EUV) images of the corona at low solar activity during the initial period of the 24th solar cycle (2010). It is shown that a SW velocity profile can be calculated from the relative areas of coronal holes (CH) at the central part of the disk based on the images in the ranges of 193 and 171 Å. The images in the 193 Å describe the geometry of large HCs that represent sources of fast SW well. The images in 171 Å are a better visualization of small CHs, based on which the profile of a slow SW component was calculated to a high accuracy (up to 65 km/s). According to Hinode/EIS data of October 15, 2010, using the Doppler spectroscopy method at the streamer base over the active region 11112, the source of the outgoing plasma flux with the mean velocity of 17 km/s was localized in the magnetic field region with an intensity of less than 200 Gauss. According to the estimate, the density of the plasma flux from this source is an order of magnitude greater than the value required for explaining the distinction between the calculated and measured profiles of a slow SW velocity. For finding the transient SW component based on small-scale flare activity, SW parameters were analyzed for the periods of flares accompanied by coronal mass ejections (CMEs), and for the periods without flares, according to the data obtained in 2010 from the ACE and GOES satellites and by coronagraphs on the STEREO-A and - B spacecraft. The ion ratios C+6/C+5 and O+7/O+6 and the mean charge of Fe ions for periods with flares were shown to be shifted toward large values, suggesting the presence of a hot SW component associated with flare activity. A noticeable correlation between the maximum charge of Fe ions and the peak power of a flare, previously observed for flares of a higher class, was confirmed. The mean value of the SW flux density during the periods of flares was 30% higher than that in the periods without flares, which is possibly associated also with the growth of fluxes from other sources with an increasing solar activity level. Based on the example of a series of flares of October 13-14, 2010, it was supposed that transient SW fluxes from the weak flares at low solar activity can manifest themselves in the form of interplanetary ICME-transients.

Quantification of the Energy Dissipated by Alfven Waves in a Polar Coronal Hole

NASA Astrophysics Data System (ADS)

Hahn, M.; Savin, D. W.

2013-12-01

We present a measurement of the energy carried and dissipated by Alfven waves in a polar coronal hole. Alfven waves have been proposed as the energy source that heats the corona and drives the solar wind. Previous work has shown that line widths decrease with height in coronal holes, which is a signature of wave damping, but have been unable to quantify the energy lost by the waves. This is because line widths depend on both the non-thermal velocity vnt and the ion temperature Ti. We have implemented a means to separate the Ti and vnt contributions using the observation that, at low heights, the waves are undamped and the ion temperatures do not change with height. This enables us to determine the amount of energy carried by the waves at low heights, which is proportional to vnt. We find the initial energy flux density present was 6.7×0.7×10^5 erg cm^-2 s^-1, which is sufficient to heat the coronal hole and accelerate the solar wind during the 2007 - 2009 solar minimum. Additionally, we find that about 85% of this energy is dissipated below 1.5 R_sun, sufficiently low that thermal conduction can transport the energy throughout the coronal hole, heating it and driving the fast solar wind. The remaining energy is roughly consistent with what models show is needed to provide the extended heating above the sonic point for the fast solar wind. We have also studied Ti, which we found to be in the range of 1 - 2 MK, depending on the ion species.

Does correction of preoperative coronal imbalance make a difference in outcomes of adult patients with deformity?

PubMed

Daubs, Michael D; Lenke, Lawrence G; Bridwell, Keith H; Kim, Yongjung J; Hung, Man; Cheh, Gene; Koester, Linda A

2013-03-15

Retrospective study with prospectively collected outcomes data. Determine the significance of coronal balance on spinal deformity surgery outcomes. Sagittal balance has been confirmed as an important radiographic parameter correlating with adult deformity treatment outcomes. The significance of coronal balance on functional outcomes is less clear. Eighty-five patients with more than 4 cm of coronal imbalance who underwent reconstructive spinal surgery were evaluated to determine the significance of coronal balance on functional outcomes as measured with the Oswestry Disability Index (ODI) and Scoliosis Research Society outcomes questionnaires. Sixty-two patients had combined coronal (>4 cm) and sagittal imbalance (>5 cm), while 23 patients had coronal imbalance alone. Postoperatively, 85% of patients demonstrated improved coronal balance. The mean improvement in the coronal C7 plumb line was 26 mm for a mean correction of 42%. The mean preoperative sagittal C7 plumb line in patients with combined coronal and sagittal imbalance was 118 mm (range, 50-310 mm) and improved to a mean 49 mm. The mean preoperative and postoperative ODI scores were 42 (range, 0-90) and 27 (range, 0-78), for a mean improvement of 15 (36%) (P = 0.00001; 95% CI, 12-20). The mean Scoliosis Research Society scores improved by 17 points (29%) (P = 0.00). Younger age (P = 0.008) and improvement in sagittal balance (P = 0.014) were positive predictors for improved ODI scores. Improvement in sagittal balance (P = 0.010) was a positive predictor for improved Scoliosis Research Society scores. In patients with combined coronal and sagittal imbalance, improvement in sagittal balance was the most significant predictor for improved ODI scores (P = 0.009). In patients with preoperative coronal imbalance alone, improvement in coronal balance trended toward, but was not a significant predictor for improved ODI (P = 0.092). Sagittal balance improvement is the strongest predictor of improved outcomes in patients with combined coronal and sagittal imbalance. In patients with coronal imbalance alone, improvement in coronal balance was not a factor for predicting improved functional outcomes.

Correlation of Coronal Plasma Properties and Solar Magnetic Field in a Decaying Active Region

NASA Technical Reports Server (NTRS)

Ko, Yuan-Kuen; Young, Peter R.; Muglach, Karin; Warren, Harry P.; Ugarte-Urra, Ignacio

2016-01-01

We present the analysis of a decaying active region observed by the EUV Imaging Spectrometer on Hinode during 2009 December 7-11. We investigated the temporal evolution of its structure exhibited by plasma at temperatures from 300,000 to 2.8 million degrees, and derived the electron density, differential emission measure, effective electron temperature, and elemental abundance ratios of Si/S and Fe/S (as a measure of the First Ionization Potential (FIP) Effect). We compared these coronal properties to the temporal evolution of the photospheric magnetic field strength obtained from the Solar and Heliospheric Observatory Michelson Doppler Imager magnetograms. We find that, while these coronal properties all decreased with time during this decay phase, the largest change was at plasma above 1.5 million degrees. The photospheric magnetic field strength also decreased with time but mainly for field strengths lower than about 70 Gauss. The effective electron temperature and the FIP bias seem to reach a basal state (at 1.5 x 10(exp 6) K and 1.5, respectively) into the quiet Sun when the mean photospheric magnetic field (excluding all areas <10 G) weakened to below 35 G, while the electron density continued to decrease with the weakening field. These physical properties are all positively correlated with each other and the correlation is the strongest in the high-temperature plasma. Such correlation properties should be considered in the quest for our understanding of how the corona is heated. The variations in the elemental abundance should especially be considered together with the electron temperature and density.

Theoretical scaling law of coronal magnetic field and electron power-law index in solar microwave burst sources

NASA Astrophysics Data System (ADS)

Huang, Y.; Song, Q. W.; Tan, B. L.

2018-04-01

It is first proposed a theoretical scaling law respectively for the coronal magnetic field strength B and electron power-law index δ versus frequency and coronal height in solar microwave burst sources. Based on the non-thermal gyro-synchrotron radiation model (Ramaty in Astrophys. J. 158:753, 1969), B and δ are uniquely solved by the observable optically-thin spectral index and turnover (peak) frequency, the other parameters (plasma density, temperature, view angle, low and high energy cutoffs, etc.) are relatively insensitive to the calculations, thus taken as some typical values. Both of B and δ increase with increasing of radio frequency but with decreasing of coronal height above photosphere, and well satisfy a square or cubic logarithmic fitting.

Radiative transfer of X-rays in the solar corona

NASA Technical Reports Server (NTRS)

Acton, L. W.

1978-01-01

The problem of resonance scattering of X-ray emission lines in the solar corona is investigated. For the resonance lines of some helium-like ions, significant optical depths are reached over distances small compared with the size of typical coronal features. A general integral equation for the transfer of resonance-line radiation under solar coronal conditions is derived. This expression is in a form useful for modeling the complex three-dimensional temperature and density structure of coronal active regions. The transfer equation is then cast in a form illustrating the terms which give rise to the attenuation or enhancement of the resonance-line intensity. The source function for helium-like oxygen (O VII) under coronal conditions is computed and discussed in terms of the relative importance of scattering.

A search at two eclipses for short-period waves that heat the corona

NASA Astrophysics Data System (ADS)

Pasachoff, Jay M.; Babcock, Bryce A.; Russell, Kevin D.; McConnochie, Timothy H.; Diaz, J. Sebastian

2000-08-01

As part of a study of the cause of solar coronal heating, we searched for high-frequency (~1 Hz) intensity oscillations in coronal loops in the [Fexiv] coronal green line. We summarize results from observations made at the 3 November 1994, total solar eclipse from the International Astronomical Union site in Putre, Chile, through partly cloudy skies, and at the 26 February 1998 total solar eclipse from Nord, Aruba, through clear skies. We discuss the image reduction and analysis of two simultaneous series of coronal CCD images digitized at 10 Hz for a total time of 160 s in Chile. One series of images was taken through a filter isolating the 5303 Å[Fexiv] coronal green line and the other through a 100 Å filter in the nearby K-corona continuum. We then discuss the modifications made for the 1998 eclipse, and the image reduction and analysis for those image sequences. After standard calibrations and image alignment of both data sets, we use Fourier analysis to search in the [Fexiv] channel for intensity oscillations in loops at the base of the corona. Such oscillations in the 1-Hz range are predicted as a result of density fluctuations from the resonant absorption of MHD waves. The dissipation of a significant amount of mechanical energy from the photosphere into the corona through this mechanism could provide sufficient energy to heat the corona. At neither eclipse do we find evidence for oscillations in the [Fexiv] green line at a level greater than 2% of coronal intensity.

Properties of coronal arches

NASA Technical Reports Server (NTRS)

Davis, J. M.; Krieger, A. S.

1982-01-01

The properties of coronal arches located on the peripheries of active regions, observed during a sounding rocket flight on March 8, 1973, are discussed. The arches are found to overlie filament channels and their footpoints are traced on locations on the perimeters of supergranulation cells. The arches have a wide range of lengths although their widths are well approximated by the value 2.2 x 10 to the 9th cm. Comparison of the size of the chromospheric footprint with the arc width indicates that arches do not always expand as they ascend into the corona. The electron temperatures and densities of the plasma contained in the arches were measured and the pressure calculated; typical values are 2-million K, 1 x 10 to the 9th/cu cm, and 0.2 dyne/sq cm, respectively. The variation of these parameters with position along the length of the arch indicates that the arches are not in hydrostatic equilibrium.

Ultraviolet Thomson Scattering from Direct-Drive Coronal Plasmas in Multilayer Targets

NASA Astrophysics Data System (ADS)

Henchen, R. J.; Goncharov, V. N.; Michel, D. T.; Follett, R. K.; Katz, J.; Froula, D. H.

2014-10-01

Ultraviolet (λ4 ω = 263 nm) Thomson scattering (TS) was used to probe ion-acoustic waves (IAW's) and electron plasma waves (EPW's) from direct-drive coronal plasmas. Fifty-nine drive beams (λ3 ω = 351 nm) illuminate a spherical target with a radius of ~ 860 μ m. A series of experiments studied the effect of higher electron temperature near the 3 ω quarter-critical surface (~ 2 . 5 ×1021 cm-3) on laser-plasma interactions resulting from a Si layer in the target. Electron temperatures and densities were measured from 150 to 400 μm from the initial target surface. Standard CH shells were compared to two-layered shells of CH and Si and three-layered shells of CH, Si, and CH. These multilayer targets have less hot-electron energy than standard CH shells as a result of higher electron temperature in the coronal plasmas. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Electric currents and coronal heating in NOAA active region 6952

NASA Technical Reports Server (NTRS)

Metcalf, T. R.; Canfield, R. C.; Hudson, H. S.; Mickey, D. L.; Wulser, J. -P.; Martens, P. C. H.; Tsuneta, S.

1994-01-01

We examine the spatial and temporal relationship between coronal structures observed with the soft X-ray telescope (SXT) on board the Yohkoh spacecraft and the vertical electric current density derived from photospheric vector magnetograms obtained using the Stokes Polarimeter at the Mees Solar Observatory. We focus on a single active region: AR 6952 which we observed on 7 days during 1991 December. For 11 independent maps of the vertical electric current density co-aligned with non-flaring X-ray images, we search for a morphological relationship between sites of high vertical current density in the photosphere and enhanced X-ray emission in the overlying corona. We find no compelling spatial or temporal correlation between the sites of vertical current and the bright X-ray structures in this active region.

CONSTRAINING THE SOLAR CORONAL MAGNETIC FIELD STRENGTH USING SPLIT-BAND TYPE II RADIO BURST OBSERVATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kishore, P.; Ramesh, R.; Hariharan, K.

2016-11-20

We report on low-frequency radio (85–35 MHz) spectral observations of four different type II radio bursts, which exhibited fundamental-harmonic emission and split-band structure. Each of the bursts was found to be closely associated with a whitelight coronal mass ejection (CME) close to the Sun. We estimated the coronal magnetic field strength from the split-band characteristics of the bursts, by assuming a model for the coronal electron density distribution. The choice of the model was constrained, based on the following criteria: (1) when the radio burst is observed simultaneously in the upper and lower bands of the fundamental component, the locationmore » of the plasma level corresponding to the frequency of the burst in the lower band should be consistent with the deprojected location of the leading edge (LE) of the associated CME; (2) the drift speed of the type II bursts derived from such a model should agree closely with the deprojected speed of the LE of the corresponding CMEs. With the above conditions, we find that: (1) the estimated field strengths are unique to each type II burst, and (2) the radial variation of the field strength in the different events indicate a pattern. It is steepest for the case where the heliocentric distance range over which the associated burst is observed is closest to the Sun, and vice versa.« less

Why is solar cycle 24 an inefficient producer of high-energy particle events?

NASA Astrophysics Data System (ADS)

Vainio, Rami; Raukunen, Osku; Tylka, Allan J.; Dietrich, William F.; Afanasiev, Alexandr

2017-08-01

Aims: The aim of the study is to investigate the reason for the low productivity of high-energy SEPs in the present solar cycle. Methods: We employ scaling laws derived from diffusive shock acceleration theory and simulation studies including proton-generated upstream Alfvén waves to find out how the changes observed in the long-term average properties of the erupting and ambient coronal and/or solar wind plasma would affect the ability of shocks to accelerate particles to the highest energies. Results: Provided that self-generated turbulence dominates particle transport around coronal shocks, it is found that the most crucial factors controlling the diffusive shock acceleration process are the number density of seed particles and the plasma density of the ambient medium. Assuming that suprathermal populations provide a fraction of the particles injected to shock acceleration in the corona, we show that the lack of most energetic particle events as well as the lack of low charge-to-mass ratio ion species in the present cycle can be understood as a result of the reduction of average coronal plasma and suprathermal densities in the present cycle over the previous one.

Toward Understanding the Early Stags of an Impulsively Accelerated Coronal Mass Ejection

DTIC Science & Technology

2010-08-09

B. E., & Howard, R. A . 2009, ApJ, 702, 901 Wood, B. E., Karovska , M., Chen, J., Brueckner, G. E., Cook, J. W., & Howard, R. A . 1999, ApJ, 512, 484...ar X iv :1 00 8. 11 71 v1 [ as tr o- ph .S R ] 6 A ug 2 01 0 Astronomy & Astrophysics manuscript no. bubble c© ESO 2010 August 9, 2010 Toward...understanding the early stages of an impulsively accelerated coronal mass ejection SECCHI observations S. Patsourakos1, A . Vourlidas2, and B. Kliem3,4

DIRECT OBSERVATION OF SOLAR CORONAL MAGNETIC FIELDS BY VECTOR TOMOGRAPHY OF THE CORONAL EMISSION LINE POLARIZATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramar, M.; Lin, H.; Tomczyk, S., E-mail: kramar@cua.edu, E-mail: lin@ifa.hawaii.edu, E-mail: tomczyk@ucar.edu

We present the first direct “observation” of the global-scale, 3D coronal magnetic fields of Carrington Rotation (CR) Cycle 2112 using vector tomographic inversion techniques. The vector tomographic inversion uses measurements of the Fe xiii 10747 Å Hanle effect polarization signals by the Coronal Multichannel Polarimeter (CoMP) and 3D coronal density and temperature derived from scalar tomographic inversion of Solar Terrestrial Relations Observatory (STEREO)/Extreme Ultraviolet Imager (EUVI) coronal emission lines (CELs) intensity images as inputs to derive a coronal magnetic field model that best reproduces the observed polarization signals. While independent verifications of the vector tomography results cannot be performed, wemore » compared the tomography inverted coronal magnetic fields with those constructed by magnetohydrodynamic (MHD) simulations based on observed photospheric magnetic fields of CR 2112 and 2113. We found that the MHD model for CR 2112 is qualitatively consistent with the tomography inverted result for most of the reconstruction domain except for several regions. Particularly, for one of the most noticeable regions, we found that the MHD simulation for CR 2113 predicted a model that more closely resembles the vector tomography inverted magnetic fields. In another case, our tomographic reconstruction predicted an open magnetic field at a region where a coronal hole can be seen directly from a STEREO-B/EUVI image. We discuss the utilities and limitations of the tomographic inversion technique, and present ideas for future developments.« less

Magnetic Untwisting in Solar Jets that Go into the Outer Corona in Polar Coronal Holes

NASA Technical Reports Server (NTRS)

Moore, Ronald L.; Sterling, Alphonse C.; Falconer, David A.

2014-01-01

We present results from 14 exceptionally high-reaching large solar jets observed in the polar coronal holes. EUV movies from SDO/AIA show that each jet is similar to many other similar-size and smaller jets that erupt in coronal holes, but each is exceptional in that it goes higher than most other jets, so high that it is observed in the outer corona beyond 2.2 R(sub Sun) in images from the SOHO/LASCO/C2 coronagraph. For these high-reaching jets, we find: (1) the front of the jet transits the corona below 2.2 R(sub Sun) at a speed typically several times the sound speed; (2) each jet displays an exceptionally large amount of spin as it erupts; (3) in the outer corona, most jets display oscillatory swaying having an amplitude of a few degrees and a period of order 1 hour. We conclude that these jets are magnetically driven, propose that the driver is a magnetic-untwisting wave that is grossly a large-amplitude (i.e., nonlinear) torsional Alfven wave that is put into the reconnected open magnetic field in the jet by interchange reconnection as the jet erupts, and estimate from the measured spinning and swaying that the magnetic-untwisting wave loses most of its energy in the inner corona below 2.2 R(sub Sun). From these results for these big jets, we reason that the torsional magnetic waves observed in Type-II spicules should dissipate in the corona in the same way and could thereby power much of the coronal heating in coronal holes.

Tracking of an electron beam through the solar corona with LOFAR

NASA Astrophysics Data System (ADS)

Mann, G.; Breitling, F.; Vocks, C.; Aurass, H.; Steinmetz, M.; Strassmeier, K. G.; Bisi, M. M.; Fallows, R. A.; Gallagher, P.; Kerdraon, A.; Mackinnon, A.; Magdalenic, J.; Rucker, H.; Anderson, J.; Asgekar, A.; Avruch, I. M.; Bell, M. E.; Bentum, M. J.; Bernardi, G.; Best, P.; Bîrzan, L.; Bonafede, A.; Broderick, J. W.; Brüggen, M.; Butcher, H. R.; Ciardi, B.; Corstanje, A.; Gasperin, F. de; Geus, E. de; Deller, A.; Duscha, S.; Eislöffel, J.; Engels, D.; Falcke, H.; Fender, R.; Ferrari, C.; Frieswijk, W.; Garrett, M. A.; Grießmeier, J.; Gunst, A. W.; van Haarlem, M.; Hassall, T. E.; Heald, G.; Hessels, J. W. T.; Hoeft, M.; Hörandel, J.; Horneffer, A.; Juette, E.; Karastergiou, A.; Klijn, W. F. A.; Kondratiev, V. I.; Kramer, M.; Kuniyoshi, M.; Kuper, G.; Maat, P.; Markoff, S.; McFadden, R.; McKay-Bukowski, D.; McKean, J. P.; Mulcahy, D. D.; Munk, H.; Nelles, A.; Norden, M. J.; Orru, E.; Paas, H.; Pandey-Pommier, M.; Pandey, V. N.; Pizzo, R.; Polatidis, A. G.; Rafferty, D.; Reich, W.; Röttgering, H.; Scaife, A. M. M.; Schwarz, D. J.; Serylak, M.; Sluman, J.; Smirnov, O.; Stappers, B. W.; Tagger, M.; Tang, Y.; Tasse, C.; ter Veen, S.; Thoudam, S.; Toribio, M. C.; Vermeulen, R.; van Weeren, R. J.; Wise, M. W.; Wucknitz, O.; Yatawatta, S.; Zarka, P.; Zensus, J. A.

2018-03-01

The Sun's activity leads to bursts of radio emission, among other phenomena. An example is type-III radio bursts. They occur frequently and appear as short-lived structures rapidly drifting from high to low frequencies in dynamic radio spectra. They are usually interpreted as signatures of beams of energetic electrons propagating along coronal magnetic field lines. Here we present novel interferometric LOFAR (LOw Frequency ARray) observations of three solar type-III radio bursts and their reverse bursts with high spectral, spatial, and temporal resolution. They are consistent with a propagation of the radio sources along the coronal magnetic field lines with nonuniform speed. Hence, the type-III radio bursts cannot be generated by a monoenergetic electron beam, but by an ensemble of energetic electrons with a spread distribution in velocity and energy. Additionally, the density profile along the propagation path is derived in the corona. It agrees well with three-fold coronal density model by (1961, ApJ, 133, 983).

Coronal holes and high-speed wind streams

NASA Technical Reports Server (NTRS)

Zirker, J. B.

1977-01-01

Coronal holes, regions of unusually low density and low temperature in the solar corona, are identified as Bartel's M regions, i.e., sources of high-speed wind streams that produce recurrent geomagnetic variations. Throughout the Skylab period the polar caps of the sun were coronal holes, and at lower latitudes the most persistent and recurrent holes were equatorial extensions of the polar caps. The holes rotated 'rigidly' at the equatorial synodic rate. They formed in regions of unipolar photospheric magnetic field, and their internal magnetic fields diverged rapidly with increasing distance from the sun. The geometry of the magnetic field in the inner corona seems to control both the physical properties of the holes and the global distribution of high-speed wind streams in the heliosphere. Phenomenological models for the birth and decay of coronal holes have been proposed.

Preliminary optical design of the coronagraph for the ASPIICS formation flying mission

NASA Astrophysics Data System (ADS)

Vivès, S.; Lamy, P.; Saisse, M.; Boit, J.-L.; Koutchmy, S.

2017-11-01

Formation flyers open new perspectives and allow to conceive giant, externally-occulted coronagraphs using a two-component space system with the external occulter on one spacecraft and the optical instrument on the other spacecraft at approximately 100-150 m from the first one. ASPIICS (Association de Satellites Pour l'Imagerie et l'Interfromtrie de la Couronne Solaire) is a mission proposed to ESA in the framework of the PROBA-3 program of formation flying which is presently in phase A to exploit this technique for coronal observations. ASPIICS is composed of a single coronagraph which performs high spatial resolution imaging of the corona as well as 2-dimensional spectroscopy of several emission lines from the coronal base out to 3 R. The selected lines allow to address different coronal regions: the forbidden line of Fe XIV at 530.285 nm (coronal matter), Fe IX/X at 637.4 nm (coronal holes), HeI at 587.6 nm (cold matter). An additional broad spectral channel will image the white light corona so as to derive electron densities. The classical design of an externally occulted coronagraph is adapted to the detection of the very inner corona as close as 1.01 R and the addition of a Fabry-Perot interferometer using a so-called "etalon". This paper is dedicated to the description of the optical design and its critical components: the entrance optics and the FabryPerot interferometer.

Neutral Hydrogen and Its Emission Lines in the Solar Corona

NASA Astrophysics Data System (ADS)

Vial, Jean-Claude; Chane-Yook, Martine

2016-12-01

Since the Lyman-α rocket observations of Gabriel ( Solar Phys. 21, 392, 1971), it has been realized that the hydrogen (H) lines could be observed in the corona and that they offer an interesting diagnostic for the temperature, density, and radial velocity of the coronal plasma. Moreover, various space missions have been proposed to measure the coronal magnetic and velocity fields through polarimetry in H lines. A necessary condition for such measurements is to benefit from a sufficient signal-to-noise ratio. The aim of this article is to evaluate the emission in three representative lines of H for three different coronal structures. The computations have been performed with a full non-local thermodynamic-equilibrium (non-LTE) code and its simplified version without radiative transfer. Since all collisional and radiative quantities (including incident ionizing and exciting radiation) are taken into account, the ionization is treated exactly. Profiles are presented at two heights (1.05 and 1.9 solar radii, from Sun center) in the corona, and the integrated intensities are computed at heights up to five solar radii. We compare our results with previous computations and observations ( e.g. Lα from Ultraviolet Coronal Spectrometer) and find a rough (model-dependent) agreement. Since the Hα line is a possible candidate for ground-based polarimetry, we show that in order to detect its emission in various coronal structures, it is necessary to use a very narrow (less than 2 Å wide) bandpass filter.

A SEARCH FOR SUB-SECOND RADIO VARIABILITY PREDICTED TO ARISE TOWARD 3C 84 FROM INTERGALACTIC DISPERSION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hales, C. A.; Max-Moerbeck, W.; Roshi, D. A.

2016-06-01

We empirically evaluate the scheme proposed by Lieu and Duan in which the light curve of a time-steady radio source is predicted to exhibit increased variability on a characteristic timescale set by the sightline’s electron column density. Application to extragalactic sources is of significant appeal, as it would enable a unique and reliable probe of cosmic baryons. We examine temporal power spectra for 3C 84, observed at 1.7 GHz with the Karl G. Jansky Very Large Array and the Robert C. Byrd Green Bank Telescope. These data constrain the ratio between standard deviation and mean intensity for 3C 84 tomore » less than 0.05% at temporal frequencies ranging between 0.1 and 200 Hz. This limit is 3 orders of magnitude below the variability predicted by Lieu and Duan and is in accord with theoretical arguments presented by Hirata and McQuinn rebutting electron density dependence. We identify other spectral features in the data consistent with the slow solar wind, a coronal mass ejection, and the ionosphere.« less

Steady State Model for Solar Coronal Loops

NASA Astrophysics Data System (ADS)

Sugiyama, L.; Asgari-Targhi, M.

2017-12-01

Solar coronal loops on the surface of the sun provide background magnetic and plasma structures for the release of a significant amount of the sun's energy, through energetic solar flares and coronal mass ejections and more gradual processes. Understanding their steady states is the first step in understanding loop dynamics. A consistent MHD steady state model, for a curved magnetic flux rope that contains plasma, has been developed[1] for simple coronal loops with both ends anchored in the photosphere. Plasma pressure or current makes the loop unstable to expansion in major radius and must be balanced by external forces, such as the solar gravity. The MHD momentum equation has a well defined small parameter ordering in the loop inverse aspect ratio ɛ=a/Ro (minor/major radius). Different types of common coronal loops fall in different parameter regimes, determined by the relative values of the plasma beta β=po/(Bo2/2μo), the MHD gravity parameter Ĝ≡ga/vA2 (the gravitational acceleration g normalized to the minor radius a and shear Alfvén velocity vA), and ɛ. The largest possible gravity, Ĝ ɛ1β, corresponds to the largest loops because it reduces the plasma density at the top of the loop exponentially compared to its lower ends, reducing the downward gravitational force -ρĜ there. The thin loops that are ubiquitous in solar active regions have ``high'' beta, β ɛ1, for ɛ≃0.02, and fit the predicted model scalings. The thicker loops that can give rise to flares and CMEs have ``low'' beta, β ɛ2. Cool loops, such as solar filaments outside active regions, that have a central pressure lower than that of the surrounding corona would have the strongest stability against radial expansion. The model raises a number of questions about the connection of loops to the photosphere and the force-free nature of the magnetic field there. [1] L. Sugiyama, M. Asgari-Targhi, Phys. Plasmas 24, 022904 (2017).

Magnetic Structure of Sites of Braiding in Hi-C Active Region

NASA Technical Reports Server (NTRS)

Tiwari, S. K.; Alexander, C. E.; Winebarger, A.; Moore, R. L.

2014-01-01

High-resolution Coronal Imager (Hi-C) observations of an active region (AR) corona, at a spatial resolution of 0.2 arcsec, have offered the first direct evidence of field lines braiding, which could deliver sufficient energy to heat the AR corona by current dissipation via magnetic reconnection, a proposal given by Parker three decades ago. The energy required to heat the corona must be transported from the photosphere along the field lines. The mechanism that drives the energy transport to the corona is not yet fully understood. To investigate simultaneous magnetic and intensity structure in and around the AR in detail, we use SDO/HMI+AIA data of + / - 2 hours around the 5 minute Hi-C flight. In the case of the QS, work done by convection/granulation on the inter-granular feet of the coronal field lines probably translates into the heat observed in the corona. In the case of the AR, as here, there could be flux emergence, cancellation/submergence, or shear flows generating large stress and tension in coronal field loops which is released as heat in the corona. However, to the best of our knowledge, there is no observational evidence available to these processes. We investigate the changes taking place in the photospheric feet of the magnetic field involved with brightenings in the Hi-C AR corona. Using HMI 45s magnetograms of four hours we find that, out of the two Hi-C sub-regions where the braiding of field lines were recently detected, flux emergence takes place in one region and flux cancellation in the other. The field in these sub-regions are highly sheared and have apparent high speed plasma flows at their feet. Therefore, shearing flows plausibly power much of the coronal and transition region heating in these areas of the AR. In addition, the presence of large flux emergence/cancellation strongly suggests that the work done by these processes on the pre-existing field also drives much of the observed heating.

Generation of coronal electric currents due to convective motions on the photosphere

NASA Astrophysics Data System (ADS)

Sakurai, T.; Levine, R. H.

1981-09-01

Generation of electric currents in a magnetized plasma overlying a dense convective layer is studied, assuming that the magnetic field perturbation is small and satisfies the force-free equation. Currents are produced by rotational motions on the boundary in the case of a uniform equilibrium field. In a simple two-dimensional bipolar configuration, however, both irrotational and incompressible motions give rise to currents, and the current density has a peak at the magnetic neutral line. Scaling laws for the current density as well as for the stored magnetic energy are derived, and the possibility of heating the solar corona through the dissipation of coronal currents generated in this way is discussed.

Generation of coronal electric currents due to convective motions on the photosphere

NASA Technical Reports Server (NTRS)

Sakurai, T.; Levine, R. H.

1981-01-01

Generation of electric currents in a magnetized plasma overlying a dense convective layer is studied, assuming that the magnetic field perturbation is small and satisfies the force-free equation. Currents are produced by rotational motions on the boundary in the case of a uniform equilibrium field. In a simple two-dimensional bipolar configuration, however, both irrotational and incompressible motions give rise to currents, and the current density has a peak at the magnetic neutral line. Scaling laws for the current density as well as for the stored magnetic energy are derived, and the possibility of heating the solar corona through the dissipation of coronal currents generated in this way is discussed.

Explaining Warm Coronal Loops

NASA Technical Reports Server (NTRS)

Klimchuk, James A.; Karpen, Judy T.; Patsourakos, Spiros

2008-01-01

One of the great mysteries of coronal physics that has come to light in the last few years is the discovery that warn (- 1 INK) coronal loops are much denser than expected for quasi-static equilibrium. Both the excess densities and relatively long lifetimes of the loops can be explained with bundles of unresolved strands that are heated impulsively to very high temperatures. Since neighboring strands are at different stages of cooling, the composite loop bundle is multi-thermal, with the distribution of temperatures depending on the details of the "nanoflare storm." Emission hotter than 2 MK is predicted, but it is not clear that such emission is always observed. We consider two possible explanations for the existence of over-dense warm loops without corresponding hot emission: (1) loops are bundles of nanoflare heated strands, but a significant fraction of the nanoflare energy takes the form of a nonthermal electron beam rather then direct plasma heating; (2) loops are bundles of strands that undergo thermal nonequilibrium that results when steady heating is sufficiently concentrated near the footpoints. We present numerical hydro simulations of both of these possibilities and explore the observational consequences, including the production of hard X-ray emission and absorption by cool material in the corona.

Optical design of visible emission line coronagraph on Indian space solar mission Aditya-L1

NASA Astrophysics Data System (ADS)

Raj Kumar, N.; Raghavendra Prasad, B.; Singh, Jagdev; Venkata, Suresh

2018-04-01

The ground based observations of the coronal emission lines using a coronagraph are affected by the short duration of clear sky and varying sky transparency. These conditions do not permit to study small amplitude variations in the coronal emission reliably necessary to investigate the process or processes involved in heating the coronal plasma and dynamics of solar corona. The proposed Visible Emission Line Coronagraph (VELC) over comes these limitations and will provide continuous observation 24 h a day needed for detailed studies of solar corona and drivers for space weather predictions. VELC payload onboard India's Aditya-L1 space mission is an internally occulted solar coronagraph for studying the temperature, velocity, density and heating of solar corona. To achieve the proposed science goals, an instrument which is capable of carrying out simultaneous imaging, spectroscopy and spectro-polarimetric observations of the solar corona close to the solar limb is required. VELC is designed with salient features of (a) Imaging solar corona at 500 nm with an angular resolution of 5 arcsec over a FOV of 1.05Ro to 3Ro (Ro:Solar radius) (b) Simultaneous multi-slit spectroscopy at 530.3 nm [Fe XIV],789.2 nm [Fe XI] and 1074.7 nm [Fe XIII] with spectral dispersion of 28mÅ, 31mÅ and 202mÅ per pixel respectively, over a FOV of 1.05Ro to 1.5Ro. (c) Multi-slit dual beam spectro-polarimetry at 1074.7 nm. All the components of instrument have been optimized in view of the scientific objectives and requirements of space payloads. In this paper we present the details of optical configuration and the expected performance of the payload.

Identification of prominence ejecta by the proton distribution function and magnetic fine structure in interplanetary coronal mass ejections in the inner heliosphere

NASA Astrophysics Data System (ADS)

Yao, Shuo; Marsch, Eckart; Tu, Chuan-Yi; Schwenn, Rainer

2010-05-01

This work presents in situ solar wind observations of three magnetic clouds (MCs) that contain cold high-density material when Helios 2 was located at 0.3 AU on 9 May 1979, 0.5 AU on 30 March 1976, and 0.7 AU on 24 December 1978. In the cold high-density regions embedded in the interplanetary coronal mass ejections we find (1) that the number density of protons is higher than in other regions inside the magnetic cloud, (2) the possible existence of He+, (3) that the thermal velocity distribution functions are more isotropic and appear to be colder than in the other regions of the MC, and the proton temperature is lower than that of the ambient plasma, and (4) that the associated magnetic field configuration can for all three MC events be identified as a flux rope. This cold high-density region is located at the polarity inversion line in the center of the bipolar structure of the MC magnetic field (consistent with previous solar observation work that found that a prominence lies over the neutral line of the related bipolar solar magnetic field). Specifically, for the first magnetic cloud event on 8 May 1979, a coronal mass ejection (CME) was related to an eruptive prominence previously reported as a result of the observation of Solwind (P78-1). Therefore, we identify the cold and dense region in the MC as the prominence material. It is the first time that prominence ejecta were identified by both the plasma and magnetic field features inside 1 AU, and it is also the first time that the thermal ion velocity distribution functions were used to investigate the microstate of the prominence material. Moreover, from our three cases, we also found that this material tended to fall behind the magnetic cloud and become smaller as it propagated farther away from the Sun, which confirms speculations in previous work. Overall, our in situ observations are consistent with three-part CME models.

Corotating solar wind structures and recurrent trains of enhanced diurnal variation in galactic cosmic rays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeeram, T.; Ruffolo, D.; Sáiz, A.

Data from the Princess Sirindhorn Neutron Monitor at Doi Inthanon, Thailand, with a vertical cutoff rigidity of 16.8 GV, were utilized to determine the diurnal anisotropy (DA) of Galactic cosmic rays (GCRs) near Earth during solar minimum conditions between 2007 November and 2010 November. We identified trains of enhanced DA over several days, which often recur after a solar rotation period (∼27 days). By investigating solar coronal holes as identified from synoptic maps and solar wind parameters, we found that the intensity and anisotropy of cosmic rays are associated with the high-speed streams (HSSs) in the solar wind, which aremore » in turn related to the structure and evolution of coronal holes. An enhanced DA was observed after the onset of some, but not all, HSSs. During time periods of recurrent trains, the DA was often enhanced or suppressed according to the sign of the interplanetary magnetic field B, which suggests a contribution from a mechanism involving a southward gradient in the GCR density, n, and a gradient anisotropy along B × ∇n. In one non-recurrent and one recurrent sequence, an HSS from an equatorial coronal hole was merged with that from a trailing mid-latitude extension of a polar coronal hole, and the slanted HSS structure in space with suppressed GCR density can account for the southward GCR gradient. We conclude that the gradient anisotropy is a source of temporary changes in the GCR DA under solar minimum conditions, and that the latitudinal GCR gradient can sometimes be explained by the coronal hole morphology.« less

V.L.A. Observations of Solar-Active Regions. I. The Slowly Varying Component,

DTIC Science & Technology

1980-08-01

bremsstrahlung accounts for the highly polarized radiation. In this situation the magnetic energy 2 % 4 -3 density of H /(8T) 10 erg cm vastly exceeds the...equipartition value inferred from the virial theorem, for the thermal kinetic energy density in -3 the "coronal condensations" is 3N kT 5 erg cm . It...Boston: D. Reidel). Kundu, M.R., 1959a, Ann. Ap., 22, 1. Kundu, M.R., 1959b, "Etude Interferometrique des Sources d’Activite Solaire sur 3 cm de

The Strength and Radial Profile of the Coronal Magnetic Field from the Standoff Distance of a Coronal Mass Ejection-Driven Shock

NASA Technical Reports Server (NTRS)

Gopalswamy, Nat; Yashiro, Seiji

2011-01-01

We determine the coronal magnetic field strength in the heliocentric distance range 6-23 solar radii (Rs) by measuring the shock standoff distance and the radius of curvature of the flux rope during the 2008 March 25 coronal mass ejection imaged by white-light coronagraphs. Assuming the adiabatic index, we determine the Alfven Mach number, and hence the Alfven speed in the ambient medium using the measured shock speed. By measuring the upstream plasma density using polarization brightness images, we finally get the magnetic field strength upstream of the shock. The estimated magnetic field decreases from approximately 48 mG around 6 Rs to 8 mG at 23 Rs. The radial profile of the magnetic field can be described by a power law in agreement with other estimates at similar heliocentric distances.

1975 Memorial Award Paper. Image generation and display techniques for CT scan data. Thin transverse and reconstructed coronal and sagittal planes.

PubMed

Glenn, W V; Johnston, R J; Morton, P E; Dwyer, S J

1975-01-01

The various limitations to computerized axial tomographic (CT) interpretation are due in part to the 8-13 mm standard tissue plane thickness and in part to the absence of alternative planes of view, such as coronal or sagittal images. This paper describes a method for gathering multiple overlapped 8 mm transverse sections, subjecting these data to a deconvolution process, and then displaying thin (1 mm) transverse as well as reconstructed coronal and sagittal CT images. Verification of the deconvolution technique with phantom experiments is described. Application of the phantom results to human post mortem CT scan data illustrates this method's faithful reconstruction of coronal and sagittal tissue densities when correlated with actual specimen photographs of a sectioned brain. A special CT procedure, limited basal overlap scanning, is proposed for use on current first generation CT scanners without hardware modification.

Identification and analysis of structures in the corona from X-ray photography

NASA Technical Reports Server (NTRS)

Vaiana, G. S.; Krieger, A. S.; Timothy, A. F.

1973-01-01

This paper summarizes the results of a program of rocket observations of the solar corona with grazing incidence X-ray telescopes. A series of five flights of a Kanigen-surfaced telescope with a few arc seconds resolution, together with the first flight of a newer telescope have resulted in the identification of six classes of coronal structures observable in the X-ray photographs. These are: active regions, active region interconnections, large loop structures associated with unipolar magnetic regions, coronal holes, coronal bright points, and the structures surrounding filament cavities. Two solar flares have been observed. The methods involved in deriving coronal temperature and density information from X-ray photographs are described and the analysis of a bright active region (McMath plage 11035) observed at the west limb on November 24, 1970 is presented as an example of these techniques.

The COronal Solar Magnetism Observatory (COSMO) Large Aperture Coronagraph

NASA Astrophysics Data System (ADS)

Tomczyk, Steve; Gallagher, Dennis; Wu, Zhen; Zhang, Haiying; Nelson, Pete; Burkepile, Joan; Kolinksi, Don; Sutherland, Lee

2013-04-01

The COSMO is a facility dedicated to observing coronal and chromospheric magnetic fields. It will be located on a mountaintop in the Hawaiian Islands and will replace the current Mauna Loa Solar Observatory (MLSO). COSMO will provide unique observations of the global coronal magnetic fields and its environment to enhance the value of data collected by other observatories on the ground (e.g. SOLIS, BBO NST, Gregor, ATST, EST, Chinese Giant Solar Telescope, NLST, FASR) and in space (e.g. SDO, Hinode, SOHO, GOES, STEREO, Solar-C, Solar Probe+, Solar Orbiter). COSMO will employ a fleet of instruments to cover many aspects of measuring magnetic fields in the solar atmosphere. The dynamics and energy flow in the corona are dominated by magnetic fields. To understand the formation of CMEs, their relation to other forms of solar activity, and their progression out into the solar wind requires measurements of coronal magnetic fields. The large aperture coronagraph, the Chromospheric and Prominence Magnetometer and the K-Coronagraph form the COSMO instrument suite to measure magnetic fields and the polarization brightness of the low corona used to infer electron density. The large aperture coronagraph will employ a 1.5 meter fuse silica singlet lens, birefringent filters, and a spectropolarimeter to cover fields of view of up to 1 degree. It will observe the corona over a wide range of emission lines from 530.3 nm through 1083.0 nm allowing for magnetic field measurements over a wide range of coronal temperatures (e.g. FeXIV at 530.3 nm, Fe X at 637.4 nm, Fe XIII at 1074.7 and 1079.8 nm. These lines are faint and require the very large aperture. NCAR and NSF have provided funding to bring the large aperture coronagraph to a preliminary design review state by the end of 2013. As with all data from Mauna Loa, the data products from COSMO will be available to the community via the Mauna Loa website: http://mlso.hao.ucar.edu

Radio Emmision during the interaction of two Interplanetary Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Lara, Alejandro; Niembro, Tatiana; González, Ricardo

2016-07-01

We show that some sporadic radio emission observed by the WIND/WAVES experiment in the decametric/kilometric bands are due to the interaction of two interplanetary Coronal Mass Ejections. We have performed hydrodynamic simulations of the evolution of two consecutive Coronal Mass ejections in the interplanetary medium. With these simulations it is possible to follow the density evolution of the merged structure, and therefore, compute the frequency limits of the possible plasma emission. We study four well documented ICME interaction events, and found radio emission at the time and frequencies predicted by the simulations. This emission may help to anticipate the complexity of the merged region before it reaches one AU.

Hot prominence detected in the core of a coronal mass ejection. II. Analysis of the C III line detected by SOHO/UVCS

NASA Astrophysics Data System (ADS)

Jejčič, S.; Susino, R.; Heinzel, P.; Dzifčáková, E.; Bemporad, A.; Anzer, U.

2017-11-01

Context. We study the physics of erupting prominences in the core of coronal mass ejections (CMEs) and present a continuation of a previous analysis. Aims: We determine the kinetic temperature and microturbulent velocity of an erupting prominence embedded in the core of a CME that occurred on August 2, 2000 using the Ultraviolet Coronagraph and Spectrometer observations (UVCS) on board the Solar and Heliospheric Observatory (SOHO) simultaneously in the hydrogen Lα and C III lines. We develop the non-LTE (departures from the local thermodynamic equilibrium - LTE) spectral diagnostics based on Lα and Lβ measured integrated intensities to derive other physical quantities of the hot erupting prominence. Based on this, we synthesize the C III line intensity to compare it with observations. Methods: Our method is based on non-LTE modeling of eruptive prominences. We used a general non-LTE radiative-transfer code only for optically thin prominence points because optically thick points do not allow the direct determination of the kinetic temperature and microturbulence from the line profiles. The input parameters of the code were the kinetic temperature and microturbulent velocity derived from the Lα and C III line widths, as well as the integrated intensity of the Lα and Lβ lines. The code runs in three loops to compute the radial flow velocity, electron density, and effective thickness as the best fit to the Lα and Lβ integrated intensities within the accuracy defined by the absolute radiometric calibration of UVCS data. Results: We analyzed 39 observational points along the whole erupting prominence because for these points we found a solution for the kinetic temperature and microturbulent velocity. For these points we ran the non-LTE code to determine best-fit models. All models with τ0(Lα) ≤ 0.3 and τ0(C III) ≤ 0.3 were analyzed further, for which we computed the integrated intensity of the C III line using a two-level atom. The best agreement between computed and observed integrated intensity led to 30 optically thin points along the prominence. The results are presented as histograms of the kinetic temperature, microturbulent velocity, effective thickness, radial flow velocity, electron density, and gas pressure. We also show the relation between the microturbulence and kinetic temperature together with a scatter plot of computed versus observed C III integrated intensities and the ratio of the computed to observed C III integrated intensities versus kinetic temperature. Conclusions: The erupting prominence embedded in the CME is relatively hot with a low electron density, a wide range of effective thicknesses, a rather narrow range of radial flow velocities, and a microturbulence of about 25 km s-1. This analysis shows a disagreement between observed and synthetic intensities of the C III line, the reason for which most probably is that photoionization is neglected in calculations of the ionization equilibrium. Alternatively, the disagreement might be due to non-equilibrium processes.

Heating of an Erupting Prominence Associated with a Solar Coronal Mass Ejection on 2012 January 27

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jin-Yi; Moon, Yong-Jae; Kim, Kap-Sung

2017-07-20

We investigate the heating of an erupting prominence and loops associated with a coronal mass ejection and X-class flare. The prominence is seen as absorption in EUV at the beginning of its eruption. Later, the prominence changes to emission, which indicates heating of the erupting plasma. We find the densities of the erupting prominence using the absorption properties of hydrogen and helium in different passbands. We estimate the temperatures and densities of the erupting prominence and loops seen as emission features using the differential emission measure method, which uses both EUV and X-ray observations from the Atmospheric Imaging Assembly onmore » board the Solar Dynamics Observatory and the X-ray Telescope on board Hinode . We consider synthetic spectra using both photospheric and coronal abundances in these calculations. We verify the methods for the estimation of temperatures and densities for the erupting plasmas. Then, we estimate the thermal, kinetic, radiative loss, thermal conduction, and heating energies of the erupting prominence and loops. We find that the heating of the erupting prominence and loop occurs strongly at early times in the eruption. This event shows a writhing motion of the erupting prominence, which may indicate a hot flux rope heated by thermal energy release during magnetic reconnection.« less

PROBING THE SOLAR WIND ACCELERATION REGION WITH THE SUN-GRAZING COMET C/2002 S2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giordano, S.; Raymond, J. C.; Lamy, P.

Comet C/2002 S2, a member of the Kreutz family of sungrazing comets, was discovered in white-light images of the Large Angle and Spectromeric Coronagraph Experiment coronagraph on the Solar and Heliospheric Observatory (SOHO) on 2002 September 18 and observed in H I Lyα emission by the SOHO Ultraviolet Coronagraph Spectrometer (UVCS) instrument at four different heights as it approached the Sun. The H I Lyα line profiles detected by UVCS are analyzed to determine the spectral parameters: line intensity, width, and Doppler shift with respect to the coronal background. Two-dimensional comet images of these parameters are reconstructed at the differentmore » heights. A novel aspect of the observations of this sungrazing comet data is that, whereas the emission from most of the tail is blueshifted, that along one edge of the tail is redshifted. We attribute these shifts to a combination of solar wind speed and interaction with the magnetic field. In order to use the comet to probe the density, temperature, and speed of the corona and solar wind through which it passes, as well as to determine the outgassing rate of the comet, we develop a Monte Carlo simulation of the H I Lyα emission of a comet moving through a coronal plasma. From the outgassing rate, we estimate a nucleus diameter of about 9 m. This rate steadily increases as the comet approaches the Sun, while the optical brightness decreases by more than a factor of 10 and suddenly recovers. This indicates that the optical brightness is determined by the lifetimes of the grains, sodium atoms, and molecules produced by the comet.« less

Solar corona during the 1994 and 1999 eclipses

NASA Astrophysics Data System (ADS)

Badalyan, O. G.; Sýkora, J.

2008-06-01

The lower and middle layers of the corona are studied analyzing the ground-based observations carried out during the November 3, 1994 and August 11, 1999 total solar eclipses. While the 1994 eclipse took place nearby the solar activity minimum, the 1999 eclipse occurred closer to the solar cycle maximum. Structures, isolines of brightness and polarization, and topology of the magnetic field lines of force (calculated under a potential approximation) of these two coronae are mutually compared. It is confirmed that the brightness distribution in the corona corresponds to the hydrostatic distribution of density at the distances 1.2-1.8R⊙. Temperature 1.4 MK and density n0 = 3.3 × 108cm-3 are found for the equatorial coronal regions of the 1999 corona. Physical conditions in the polar coronal regions are investigated analyzing the brightness and polarization of the 1994 eclipse. We have found that the degree of polarization in polar plumes is about 10% higher than that in the inter-plumes space. Consideration of the brightness in plumes and in the adjacent background space allowed us to conclude that the temperatures there are close to 1 MK. The density in the individual plumes is near n0 = 2.7 × 108cm-3, while it decreases to about n0 = 2.0 × 108cm-3 in the inter-plumes space. It is pointed out that the simultaneous interpretation of the measured brightness and polarization struggles with some difficulties.

Automated coronal hole identification via multi-thermal intensity segmentation

NASA Astrophysics Data System (ADS)

Garton, Tadhg M.; Gallagher, Peter T.; Murray, Sophie A.

2018-01-01

Coronal holes (CH) are regions of open magnetic fields that appear as dark areas in the solar corona due to their low density and temperature compared to the surrounding quiet corona. To date, accurate identification and segmentation of CHs has been a difficult task due to their comparable intensity to local quiet Sun regions. Current segmentation methods typically rely on the use of single Extreme Ultra-Violet passband and magnetogram images to extract CH information. Here, the coronal hole identification via multi-thermal emission recognition algorithm (CHIMERA) is described, which analyses multi-thermal images from the atmospheric image assembly (AIA) onboard the solar dynamics observatory (SDO) to segment coronal hole boundaries by their intensity ratio across three passbands (171 Å, 193 Å, and 211 Å). The algorithm allows accurate extraction of CH boundaries and many of their properties, such as area, position, latitudinal and longitudinal width, and magnetic polarity of segmented CHs. From these properties, a clear linear relationship was identified between the duration of geomagnetic storms and coronal hole areas. CHIMERA can therefore form the basis of more accurate forecasting of the start and duration of geomagnetic storms.

Moreton wave, "EIT wave", and type II radio burst as manifestations of a single wave front

NASA Astrophysics Data System (ADS)

Kuzmenko, I. V.; Grechnev, V. V.; Uralov, A. M.

2011-12-01

We show that a Moreton wave, an "EIT wave," and a type II radio burst observed during a solar flare of July 13, 2004, might have been a manifestation of a single front of a decelerating shock wave, which appeared in an active region (AR) during a filament eruption. We propose describing a quasi-spheroidal wave propagating upward and along the solar surface by using relations known from a theory of a point-like explosion in a gas whose density changes along the radius according to a power law. By applying this law to fit the drop in density of the coronal plasma enveloping the solar active region, we first managed to bring the measured positions and velocities of surface Moreton wave and "EIT wave" into correspondence with the observed frequency drift rate of the meter type II radio burst. The exponent of the vertical coronal density falloff is selected by fitting the power law to the Newkirk and Saito empirical distributions in the height range of interest. Formal use of such a dependence in the horizontal direction with a different exponent appears to be reasonable up to distances of less than 200 Mm around the eruption center. It is possible to assume that the near-surface shock wave weakens when leaving this radius and finally the active region, entering the region of the quiet Sun where the coronal plasma density and the fast-mode speed are almost constant along the horizontal.

The formation flare loops by magnetic reconnection and chromospheric ablation

NASA Technical Reports Server (NTRS)

Forbes, T. G.; Malherbe, J. M.; Priest, E. R.

1989-01-01

Noncoplanar compressible reconnection theory is combined here with simple scaling arguments for ablation and radiative cooling to predict average properties of hot and cool flare loops as a function of the coronal vector magnetic field. For a coronal field strength of 100 G, the temperature of the hot flare loops decreases from 1.2 x 10 to the 7th K to 4.0 x 10 to the 6th K as the component of the coronal magnetic field perpendicular to the plane of the loops increases from 0 percent to 86 percent of the total field. When the perpendicular component exceeds 86 percent of the total field or when the altitude of the reconnection site exceeds 10 to the 6th km, flare loops no longer occur. Shock-enhanced radiative cooling triggers the formation of cool H-alpha flare loops with predicted densities of roughly 10 to the 13th/cu cm, and a small gap of roughly 1000 km is predicted to exist between the footpoints of the cool flare loops and the inner edges of the flare ribbons.

Coronal Activity in the R CrA T Association

NASA Technical Reports Server (NTRS)

Patten, Brian M.; Oliversen, Ronald J. (Technical Monitor)

2005-01-01

Brian Patten is the Principal Investigator of the NASA ROSS-ADP project Coronal Activity in the R CrA T Association. For this project we have extracted net counts and variability information for all of the X-ray sources found in 23 archival ROSAT PSPC and HRI images in the region of the R CrA T association. These data have been merged with an extensive database of optical and near-infrared photometry, optical spectroscopy, and parallax data. These data have been used to (1) identify new association members and clarify the membership status of a number of previously suspected members of the association, and (2) derive, for the first time, an accurate coronal luminosity function for the T Tauri members of this T association and make direct comparisons between the coronal luminosity functions for other T associations and those of large clusters. We have used our survey data to assess (a) the importance of the star-formation environment in initial coronal activity levels, (b) the effects of PMS evolution on dynamo activity as a function of mass and age, and (c) the level of contamination by field post-T Tauri stars on association membership surveys.

Effects of immediate and delayed loading on peri-implant trabecular structures: a cone beam CT evaluation.

PubMed

Huang, Yan; Van Dessel, Jeroen; Liang, Xin; Depypere, Maarten; Zhong, Weijian; Ma, Guowu; Lambrichts, Ivo; Maes, Frederik; Jacobs, Reinhilde

2014-12-01

To develop a method for characterizing trabecular bone microarchitecture using cone beam computed tomography (CBCT) and to evaluate trabecular bone changes after rehabilitation using immediate versus delayed implant protocols. Six mongrel dogs randomly received 27 titanium implants in the maxillary incisor or mandibular premolar areas, following one of four protocols: (1) normal extraction socket healing; (2) immediate implant placement and immediate loading; (3) delayed implant placement and delayed loading; (4) delayed implant placement and immediate loading. The animals were euthanized at 8 weeks, and block biopsies were scanned using high resolution CBCT. Standard bone structural variables were assessed in coronal, middle, and apical levels. Coronal and middle regions had more compact, more platelike, and thicker trabeculae. Protocols (2), (3), and (4) had significantly higher values (p < 0.001) than protocol (1) for bone surface density, bone surface volume ratio, and connectivity density, while significantly lower values (p < 0.001) were found for trabecular separation and fractal dimension. However, protocols (2), (3), and (4) did not show significantly different bone remodeling. Compared with normal extraction healing, the implant protocols have an improved bone structural integration. Results do not suggest a different bone remodeling pattern when a delayed versus an immediate implant protocol is used. © 2013 Wiley Periodicals, Inc.

Enthalpy-Based Thermal Evolution of Loops: II. Improvements to the Model

NASA Technical Reports Server (NTRS)

Cargill, P. J.; Bradshaw, S. J.; Klimchuk, J. A.

2011-01-01

This paper further develops the zero-dimensional (0D) hydrodynamic coronal loop model "Enthalpy-based Thermal Evolution of Loops" (EBTEL) originally proposed by Klimchuk et al (2008), which studies the plasma response to evolving coronal heating. It has typically been applied to impulsive heating events. The basis of EBTEL is the modelling of mass exchange between the corona and transition region and chromosphere in response to heating variations, with the key parameter being the ratio of transition region to coronal radiation. We develop new models for this parameter that now include gravitational stratification and a physically motivated approach to radiative cooling. A number of examples are presented, including nanoflares in short and long loops, and a small flare. It is found that while the evolution of the loop temperature is rather insensitive to the details of the model, accurate tracking of the density requires the inclusion of our new features. In particular, we are able to now obtain highly over-dense loops in the late cooling phase and decreases to the coronal density arising due to stratification. The 0D results are compared to a 1D hydro code (Hydrad). The agreement is acceptable, with the exception of the flare case where some versions of Hydrad can give significantly lower densities. This is attributed to the method used to model the chromosphere in a flare. EBTEL is suitable for general use as a tool for (a) quick-look results of loop evolution in response to a given heating function and (b) situations where the modelling of hundreds or thousands of elemental loops is needed. A single run takes a few seconds on a contemporary laptop.

Evidence for magnetic energy storage in coronal active regions

NASA Technical Reports Server (NTRS)

Krieger, A. S.; De Feiter, L. D.; Vaiana, G. S.

1976-01-01

Examination of X-ray images obtained by the S-054 X-ray spectrographic telescope on Skylab shows the presence of some atypical X-ray-emitting coronal structures in active regions which are not consistent with potential extrapolations of photospheric magnetic fields. Analysis of the observed temporal changes in the X-ray-emitting active-region structures demonstrates that the majority of these consist of brightness changes representing temperature (and perhaps density) variations of the material in the loops.

Wave Propagation Around Coronal Structures: Stratification, Buoyancy, Small Scale Formation

NASA Astrophysics Data System (ADS)

Tomlinson, S. M.; Rappazzo, F.; Velli, M.

2017-12-01

We study the propagation of waves in a coronal medium characterized by stratification and structure in density. temperature and magnetic field. It is well known that average gradients affect the propagation of Alfvén and other MHD waves via reflection, phase mixing, resonant absorption and other coupling phenomena. Here we discuss how the interplay of propagation on inhomogeneous, stratified structures with nonlinear interactions may lead to interesting effects including preferential heating, buoyancy, and plasma acceleration.

Transverse Oscillations of Coronal Loops

NASA Astrophysics Data System (ADS)

Ruderman, Michael S.; Erdélyi, Robert

2009-12-01

On 14 July 1998 TRACE observed transverse oscillations of a coronal loop generated by an external disturbance most probably caused by a solar flare. These oscillations were interpreted as standing fast kink waves in a magnetic flux tube. Firstly, in this review we embark on the discussion of the theory of waves and oscillations in a homogeneous straight magnetic cylinder with the particular emphasis on fast kink waves. Next, we consider the effects of stratification, loop expansion, loop curvature, non-circular cross-section, loop shape and magnetic twist. An important property of observed transverse coronal loop oscillations is their fast damping. We briefly review the different mechanisms suggested for explaining the rapid damping phenomenon. After that we concentrate on damping due to resonant absorption. We describe the latest analytical results obtained with the use of thin transition layer approximation, and then compare these results with numerical findings obtained for arbitrary density variation inside the flux tube. Very often collective oscillations of an array of coronal magnetic loops are observed. It is natural to start studying this phenomenon from the system of two coronal loops. We describe very recent analytical and numerical results of studying collective oscillations of two parallel homogeneous coronal loops. The implication of the theoretical results for coronal seismology is briefly discussed. We describe the estimates of magnetic field magnitude obtained from the observed fundamental frequency of oscillations, and the estimates of the coronal scale height obtained using the simultaneous observations of the fundamental frequency and the frequency of the first overtone of kink oscillations. In the last part of the review we summarise the most outstanding and acute problems in the theory of the coronal loop transverse oscillations.

On the nature of fast sausage waves in coronal loops

NASA Astrophysics Data System (ADS)

Bahari, Karam

2018-05-01

The effect of the parameters of coronal loops on the nature of fast sausage waves are investigated. To do this three models of the coronal loop considered, a simple loop model, a current-carrying loop model and a model with radially structured density called "Inner μ" profile. For all the models the Magnetohydrodynamic (MHD) equations solved analytically in the linear approximation and the restoring forces of oscillations obtained. The ratio of the magnetic tension force to the pressure gradient force obtained as a function of the distance from the axis of the loop. In the simple loop model for all values of the loop parameters the fast sausages wave have a mixed nature of Alfvénic and fast MHD waves, in the current-carrying loop model with thick annulus and low density contrast the fast sausage waves can be considered as purely Alfvénic wave in the core region of the loop, and in the "Inner μ" profile for each set of the parameters of the loop the wave can be considered as a purely Alfvénic wave in some regions of the loop.

Relation of large-scale coronal X-ray structure and cosmic rays. I - Sources of solar wind streams as defined by X-ray emission and H-alpha absorption features

NASA Technical Reports Server (NTRS)

Krieger, A. S.; Nolte, J. T.; Sullivan, J. D.; Lazarus, A. J.; Mcintosh, P. S.; Gold, R. E.; Roelof, E. C.

1975-01-01

The large-scale structure of the corona and the interplanetary medium during Carrington rotations 1601-1607 is discussed relative to recurrent high-speed solar wind streams and their coronal sources. Only streams A, C, D, and F recur on more than one rotation. Streams A and D are associated with coronal holes, while C and F originate in the high corona (20-50 solar radii) over faint X-ray emissions. The association of the streams with holes is confirmed by earlier findings that there are no large equatorial holes without an associated high-speed stream and that the area of the equatorial region of coronal holes is highly correlated with the maximum velocity observed in the associated stream near 1 AU.

THE COUPLED EVOLUTION OF ELECTRONS AND IONS IN CORONAL MASS EJECTION-DRIVEN SHOCKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manchester IV, W. B.; Van der Holst, B.; Toth, G.

2012-09-01

We present simulations of coronal mass ejections (CMEs) performed with a new two-temperature coronal model developed at the University of Michigan, which is able to address the coupled thermodynamics of the electron and proton populations in the context of a single fluid. This model employs heat conduction for electrons, constant adiabatic index ({gamma} = 5/3), and includes Alfven wave pressure to accelerate the solar wind. The Wang-Sheeley-Arge empirical model is used to determine the Alfven wave pressure necessary to produce the observed bimodal solar wind speed. The Alfven waves are dissipated as they propagate from the Sun and heat protonsmore » on open magnetic field lines to temperatures above 2 MK. The model is driven by empirical boundary conditions that includes GONG magnetogram data to calculate the coronal field, and STEREO/EUVI observations to specify the density and temperature at the coronal boundary by the Differential Emission Measure Tomography method. With this model, we simulate the propagation of fast CMEs and study the thermodynamics of CME-driven shocks. Since the thermal speed of the electrons greatly exceeds the speed of the CME, only protons are directly heated by the shock. Coulomb collisions low in the corona couple the protons and electrons allowing heat exchange between the two species. However, the coupling is so brief that the electrons never achieve more than 10% of the maximum temperature of the protons. We find that heat is able to conduct on open magnetic field lines and rapidly propagates ahead of the CME to form a shock precursor of hot electrons.« less

Numerical modeling of coronal mass ejections based on various pre-event model atmospheres

NASA Technical Reports Server (NTRS)

Suess, S. T.; Wang, A. H.; Wu, S. T.; Poletto, G.

1994-01-01

We examine how the initial state (pre-event corona) affects the numerical MHD simulation for a coronal mass ejection (CME). Earlier simulations based on a pre-event corona with a homogeneous density and temperature distribution at lower boundary (i.e. solar surface) have been used to analyze the role of streamer properties in determining the characteristics of loop-like transients. The present paper extends these studies to show how a broader class of global coronal properties leads not only to different types of CME's, but also modifies the adjacent quiet corona and/or coronal holes. We consider four pre-event coronal cases: (1) Constant boundary conditions and a polytropic gas with gamma = 1.05; (2) Non-constant (latitude dependent) boundary conditions and a polytropic gas with gamma = 1.05; (3) Constant boundary conditions with a volumetric energy source and gamma = 1.67; (4) Non-constant (latitude dependent) boundary conditions with a volumetric energy source and gamma = 1.67. In all models, the pre-event magnetic fields separate the corona into closed field regions (streamers) and open field regions. The CME's initiation is simulated by introducing at the base of the corona, within the streamer region, a standard pressure pulse and velocity change. Boundary values are determined using MHD characteristic theory. The simulations show how different CME's, including loop-like transients, clouds, and bright rays, might occur. There are significant new features in comparison to published results. We conclude that the pre-event corona is a crucial factor in dictating CME's properties.

Numerical Modeling of Coronal Mass Ejections Based on Various Pre-event Model Atmospheres

NASA Technical Reports Server (NTRS)

Wang, A. H.; Wu, S. T.; Suess, S. T.; Poletto, G.

1995-01-01

We examine how the initial state (pre-event corona) affects the numerical MHD simulation for a coronal mass ejection (CME). Earlier simulations based on a pre-event corona with a homogeneous density and temperature distribution, at the lower boundary (i.e., solar surface) have been used to analyze the role of streamer properties in determining the characteristics of loop-like transients. The present paper extends these studies to show how a broader class of global coronal properties leads not only to different types of CME's, but also modifies the adjacent quiet corona and/or coronal holes. We consider four pre-event coronal cases: (1) constant boundary conditions and a polytropic gas with gamma = 1.05; (2) non-constant (latitude dependent) boundary conditions and a polytropic gas with gamma = 1.05; (3) constant boundary conditions with a volumetric energy source and gamma = 1.67; (4) non-constant (latitude dependent) boundary conditions with a volumetric energy source and gamma = 1.67. In all models, the pre-event magnetic fields separate the corona into closed field regions (streamers) and open field regions. The CME's initiation is simulated by introducing at the base of the corona, within the streamer region, a standard pressure pulse and velocity change. Boundary values are determined using magnetohydrodynamic (MHD) characteristic theory. The simulations show how different CME's, including loop-like transients, clouds and bright rays, might occur. There are significant new features in comparison to published results. We conclude that the pre-event corona is a crucial factor in dictating CME's properties.

IRIS Observations of Coronal Rain and Prominences: Return Flows of the Chromosphere-Corona Mass Cycle

NASA Astrophysics Data System (ADS)

Liu, Wei; Berger, Thomas; Antolin, Patrick; Schrijver, Karel

2014-06-01

It has recently been recognized that a mass cycle (e.g., Berger et al. 2011; McIntosh et al. 2012) between the hot, tenuous solar corona and the cool, dense chromosphere underneath it plays an important role in the mass budget and dynamic evolution of the solar atmosphere. Although the corona ultimately loses mass through the solar wind and coronal mass ejections, a fraction of its mass returns to the chromosphere in coronal rain, downflows of prominences, and other as-yet unidentified processes. We present here analysis of joint observations of IRIS, SDO/AIA, and Hinode/SOT of such phenomena. By utilizing the wide temperature coverage (logT: 4 - 7) provided by these instruments combined, we track the coronal cooling sequence (e.g., Schrijver 2001; Liu et al. 2012; Berger et al. 2012) leading to the formation of such material at transition region or chromospheric temperatures (logT: 4 - 5) in the million-degree corona. We compare the cooling times with those expected from the radiative cooling instability. We also measure the kinematics and densities of such downflows and infer their mass fluxes, which are compared to the upward mass fluxes into the corona, e.g., those associated with spicules and flux emergence. Special attention is paid to coronal rain formed near cusp-shaped portions of coronal loops, funnel-shaped prominences at dips of coronal loops, and their respective magnetic environments. With the information about where and when such catastrophic cooling events take place, we discuss the implications for the enigmatic coronal heating mechanisms (e.g., Antolin et al. 2010).

Dynamic Power Spectral Analysis of Solar Measurements from Photospheric, Chromospheric, and Coronal Sources

NASA Technical Reports Server (NTRS)

Bouwer, S. D.; Pap, J.; Donnelly, R. F.

1990-01-01

An important aspect in the power spectral analysis of solar variability is the quasistationary and quasiperiodic nature of solar periodicities. In other words, the frequency, phase, and amplitude of solar periodicities vary on time scales ranging from active region lifetimes to solar cycle time scales. Here, researchers employ a dynamic, or running, power spectral density analysis to determine many periodicities and their time-varying nature in the projected area of active sunspot groups (S sub act). The Solar Maximum Mission/Active Cavity Radiometer Irradiance Monitor (SMM/ACRIM) total solar irradiance (S), the Nimbus-7 MgII center-to-wing ratio (R (MgII sub c/w)), the Ottawa 10.7 cm flux (F sub 10.7), and the GOES background x ray flux (X sub b) for the maximum, descending, and minimum portions of solar cycle 21 (i.e., 1980 to 1986) are used. The technique dramatically illustrates several previously unrecognized periodicities. For example, a relatively stable period at about 51 days has been found in those indices which are related to emerging magnetic fields. The majority of solar periodicities, particularly around 27, 150 and 300 days, are quasiperiodic because they vary in amplitude and frequency throughout the solar cycle. Finally, it is shown that there are clear differences between the power spectral densities of solar measurements from photospheric, chromospheric, and coronal sources.

Structure and dynamics of coronal plasmas

NASA Technical Reports Server (NTRS)

Golub, Leon

1995-01-01

The Normal Incidence X-ray Telescope (NIXT) obtained a unique set of high resolution full disk solar images which were exposed simultaneously by X-rays in a passband at 63.5 A and by visible light. The perfect alignment of a photospheric visible light image with a coronal X-ray image enables us to present observations of X-ray intensity vs an accurately determined height above the visible limb. The height at which the observed X-ray intensity peak varies from 4000 km in active regions to 9000 km in quiet regions of the sun. The interpretation of the observations stems from the previously established fact that, for the coronal loops, emission in the NIXT bandpass peaks sharply just above the footpoints. Because there is not a sharp peak in the observed X-ray intensity vs off limb height, we conclude that the loop footpoints, when viewed at the limb, are obscured by absorption in chromospheric material along the line of sight. We calculate the X-ray intensity vs height predicted by a number of different idealizations of the solar atmosphere, and we compare these calculations with the observed X-ray intensity vs height. The calculations use existing coronal and chromospheric models. In order for the calculations to reproduce the observed off limb X-ray intensities, we are forced to assume an atmosphere in which the footpoints of coronal loops are interspersed along the line of sight with cooler chromospheric material extending to heights well above the loop footpoints. We argue that the absorption coefficient for NIXT X-rays by chromospheric material is roughly proportional to the neutral hydrogen density, and we estimate an average neutral hydrogen density and scale height implied by the data.

Neutralized solar energetic particles in the inner heliosphere: a parameter study

NASA Astrophysics Data System (ADS)

Wang, Xiao-Dong; Klecker, Berndt; Futaana, Yoshifumi; Cipriani, Fabrice; Barabash, Stas; Wieser, Martin

2016-04-01

The large fluxes of solar energetic particles (SEPs) in Gradual Events, dominated by protons, are believed to be produced by the acceleration of shocks driven by coronal mass ejections (CMEs). As SEPs propagate in the lower corona, there is a chance for them to be neutralized via the charge exchange and/or recombination processes and become energetic neutral atoms (ENAs). These ENAs retain the velocity of their parent SEPs and propagate in straight lines without the influence of the interplanetary magnetic field, and therefore might potentially serve as a new window to observe the particle acceleration processes in the solar corona. STEREO/Low Energy Telescope reported the first probable observation of hydrogen ENAs between 1.6 MeV - 5 MeV from the Sun prior to an X-class flare/CME [Mewaldt et al., 2009]. While such observations were somehow controversial, Wang et al. [2014] simulated the neutralization of solar energetic protons in the corona lower than 40 RS, and the result agreed with the STEREO observation. In this work, we further developed a production model of the ENA near the sun together with a transport model toward the inner planets, and explore the dependences of the ENA characteristics against the model parameters. These parameters include the angular width of the CME, its propagation direction with respect to the Sun-observer line, the propagation speed, the particle density in the corona, the abundances of O6+ and C4+, and the reaction rate of electron impact ionization in the loss of ENAs, and the heliospheric distance of the observer. The calculated ENA flux shows that at lower energy the expected ENA flux depends most sensitively on the CME apex angle and the CME propagation direction. At higher energy the dependence on the coronal density is more prominent. References Mewaldt, R. A., R. A. Leske, E. C. Stone, A. F. Barghouty, A. W. Labrador, C. M. S. Cohen, A. C. Cummings, A. J. Davis, T. T. von Rosenvinge, and M. E. Wiedenbeck (2009), STEREO Observations of Energetic Neutral Hydrogen Atoms During the 2006 December 5 Solar Flare, Astrophys. J. Lett., 693(1), L11. Wang, L., G. Li, A. Y. Shih, R. P. Lin, and R. F. Wimmer-Schweingruber (2014), Simulation of Energetic Neutral Atoms from Solar Energetic Particles, Astrophys. J. Lett., 793(2), L37.

Coronal Heating and the Need for High-Resolution Observations

NASA Technical Reports Server (NTRS)

Klimchuk, James A.

2008-01-01

Despite excellent progress in recent years in understanding coronal heating, there remain many crucial questions that are still unanswered. Limitations in the observations are one important reason. Both theoretical and observational considerations point to the importance of small spatial scales, impulsive energy release, strong dynamics, and extreme plasma nonuniformity. As a consequence, high spatial resolution, broad temperature coverage, high temperature fidelity, and sensitivity to velocities and densities are all critical observational parameters. Current instruments lack one or more of these properties, and this has led to considerable ambiguity and confusion. In this talk, I will discuss recent ideas about coronal heating and emphasize that high spatial resolution observations, especially spectroscopic observations, are needed to make major progress on this important problem.

OBSERVING CORONAL NANOFLARES IN ACTIVE REGION MOSS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Testa, Paola; DeLuca, Ed; Golub, Leon

2013-06-10

The High-resolution Coronal Imager (Hi-C) has provided Fe XII 193A images of the upper transition region moss at an unprecedented spatial ({approx}0.''3-0.''4) and temporal (5.5 s) resolution. The Hi-C observations show in some moss regions variability on timescales down to {approx}15 s, significantly shorter than the minute-scale variability typically found in previous observations of moss, therefore challenging the conclusion of moss being heated in a mostly steady manner. These rapid variability moss regions are located at the footpoints of bright hot coronal loops observed by the Solar Dynamics Observatory/Atmospheric Imaging Assembly in the 94 A channel, and by the Hinode/X-Raymore » Telescope. The configuration of these loops is highly dynamic, and suggestive of slipping reconnection. We interpret these events as signatures of heating events associated with reconnection occurring in the overlying hot coronal loops, i.e., coronal nanoflares. We estimate the order of magnitude of the energy in these events to be of at least a few 10{sup 23} erg, also supporting the nanoflare scenario. These Hi-C observations suggest that future observations at comparable high spatial and temporal resolution, with more extensive temperature coverage, are required to determine the exact characteristics of the heating mechanism(s).« less

Ultraviolet-C irradiation to titanium implants increases peri-implant bone formation without impeding mineralization in a rabbit femur model.

PubMed

Yamazaki, Makoto; Yamada, Masahiro; Ishizaki, Ken; Sakurai, Kaoru

2015-05-01

Volume and bone quality of peri-implant supporting bone, in particular, at implant neck region, as well as bone-implant contact ratio, is important for long-term stability of implants. Ultraviolet-C (UVC) irradiation is known to enhance the osseointegration capability of titanium implants. However, the histological determination was performed only on a rat model, but not pre-clinical animal model such as a rabbit model. The purpose of this study was to determine the effects of UVC irradiation on titanium implants on the volume and mineral density of peri-implant supporting bone formation in a rabbit femur model. Acid-etched pure titanium screw implants with or without 3 mW/cm2 UVC irradiation for 48 h were placed in rabbit femur diaphyses. Peri-implant bone tissue formation was analyzed at 3 and 8 weeks post-operatively by histology and micro-CT-based bone morphometry after calibration with hydroxyl apatite phantoms. UVC pre-irradiated implants accumulated a higher density of cells and thicker and longer bone tissue attachments that continued into the inner basic lamellae of the surface of existing cortical bone at 3 and 8 weeks than the implants without irradiation. Although the bone mineral density around both implants was equivalent to that of the existing cortical bone, bone volume was greater with UVC pre-irradiation in two-thirds or more of the apical region throughout the observation period. These results indicate that UVC treatment increased the volume of cortical-like bone tissue in the coronal region of titanium implants without deterioration of bone mineral density.

Coronal Current Sheet Evolution in the Aftermath of a CME

NASA Technical Reports Server (NTRS)

Bemporad, A.; Poletto, G.; Suess, S. T.; Ko, Y.-K.; Schwadron, N. A.; Elliott, H. A.; Raymond, J. C.

2005-01-01

We report on SOHO-UVCS observations of coronal restructuring following a Coronal Mass Ejection (CME) on November 26, 2002, at the time of a SOHO-Ulysses quadrature campaign. Starting about 3 hours after the CME, which was directed towards Ulysses, UVCS began taking spectra at 1.7 solar radii, covering emission from both cool and hot plasma. Observations continued, with occasional gaps, for more than 2 days. Emission in the 974.8 Angstrom line of [Fe XVIII], indicating temperatures above 6x10(6) K, was observed throughout the campaign in a spatially limited location. Comparison with EIT images shows the [Fe XVIII] emission to overlie a growing post-flare loop system formed in the aftermath of the CME. The emission most likely originates in a current sheet overlying the arcade. Analysis of the [Fe XVIII] emission allows us to infer the evolution of physical parameters in the current sheet over the entire span of our observations: in particular, we give the temperature vs. time in the current sheet and estimate the density. Ulysses was directly above the location of the CME and intercepted the ejecta. High ionization state Fe was detected by SWICS throughout the magnetic cloud associated with the CME, although the rapid temporal variation suggests bursty, rather than smooth, reconnection in the coronal current sheet. Both the remote and in situ observations are compared with predictions of theoretical CME models.

Electron density diagnositc line ratios from the n = 3 lines of O v

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widing, K.G.; Doyle, J.G.; Dufton, P.L.

New atomic physic calculations are presented for electron excitation rates for transitions between the n = 2 and n = 3 levels of O v. These are used to calculate theoretical line intensity ratios for the 192 A, 215 A, 220 A and 248 A lines of O v. These line intensity ratios are electron density sensitive and provide valuable diagnostics at T/sub e/approx.2 x 10/sup 5/ K for samll impulsive flare events in which the transition zone ions are enhanced relative to the coronal ions. Two flares observed by NRL spectroheliograph on Skylab, on 1973 December 22 and 1974more » January 21, are studied, with electron densities of approximately 3 x 10/sup 11/ cm/sup -3/ being deduced.« less

Evidence for Precursors of the Coronal Hole Jets in Solar Bright Points

NASA Astrophysics Data System (ADS)

Bagashvili, Salome R.; Shergelashvili, Bidzina M.; Japaridze, Darejan R.; Kukhianidze, Vasil; Poedts, Stefaan; Zaqarashvili, Teimuraz V.; Khodachenko, Maxim L.; De Causmaecker, Patrick

2018-03-01

A set of 23 observations of coronal jet events that occurred in coronal bright points has been analyzed. The focus was on the temporal evolution of the mean brightness before and during coronal jet events. In the absolute majority of the cases either single or recurrent coronal jets (CJs) were preceded by slight precursor disturbances observed in the mean intensity curves. The key conclusion is that we were able to detect quasi-periodical oscillations with characteristic periods from sub-minute up to 3–4 minute values in the bright point brightness that precedes the jets. Our basic claim is that along with the conventionally accepted scenario of bright-point evolution through new magnetic flux emergence and its reconnection with the initial structure of the bright point and the coronal hole, certain magnetohydrodynamic (MHD) oscillatory and wavelike motions can be excited and these can take an important place in the observed dynamics. These quasi-oscillatory phenomena might play the role of links between different epochs of the coronal jet ignition and evolution. They can be an indication of the MHD wave excitation processes due to the system entropy variations, density variations, or shear flows. It is very likely a sharp outflow velocity transverse gradients at the edges between the open and closed field line regions. We suppose that magnetic reconnections can be the source of MHD waves due to impulsive generation or rapid temperature variations, and shear flow driven nonmodel MHD wave evolution (self-heating and/or overreflection mechanisms).

Coronal rain in magnetic bipolar weak fields

NASA Astrophysics Data System (ADS)

Xia, C.; Keppens, R.; Fang, X.

2017-07-01

Aims: We intend to investigate the underlying physics for the coronal rain phenomenon in a representative bipolar magnetic field, including the formation and the dynamics of coronal rain blobs. Methods: With the MPI-AMRVAC code, we performed three dimensional radiative magnetohydrodynamic (MHD) simulation with strong heating localized on footpoints of magnetic loops after a relaxation to quiet solar atmosphere. Results: Progressive cooling and in-situ condensation starts at the loop top due to radiative thermal instability. The first large-scale condensation on the loop top suffers Rayleigh-Taylor instability and becomes fragmented into smaller blobs. The blobs fall vertically dragging magnetic loops until they reach low-β regions and start to fall along the loops from loop top to loop footpoints. A statistic study of the coronal rain blobs finds that small blobs with masses of less than 1010 g dominate the population. When blobs fall to lower regions along the magnetic loops, they are stretched and develop a non-uniform velocity pattern with an anti-parallel shearing pattern seen to develop along the central axis of the blobs. Synthetic images of simulated coronal rain with Solar Dynamics Observatory Atmospheric Imaging Assembly well resemble real observations presenting dark falling clumps in hot channels and bright rain blobs in a cool channel. We also find density inhomogeneities during a coronal rain "shower", which reflects the observed multi-stranded nature of coronal rain. Movies associated to Figs. 3 and 7 are available at http://www.aanda.org

Reconnection-Driven Coronal-Hole Jets with Gravity and Solar Wind

NASA Technical Reports Server (NTRS)

Karpen, J. T.; Devore, C. R.; Antiochos, S. K.; Pariat, E.

2017-01-01

Coronal-hole jets occur ubiquitously in the Sun's coronal holes, at EUV and X-ray bright points associated with intrusions of minority magnetic polarity. The embedded-bipole model for these jets posits that they are driven by explosive, fast reconnection between the stressed closed field of the embedded bipole and the open field of the surrounding coronal hole. Previous numerical studies in Cartesian geometry, assuming uniform ambient magnetic field and plasma while neglecting gravity and solar wind, demonstrated that the model is robust and can produce jet-like events in simple configurations. We have extended these investigations by including spherical geometry,gravity, and solar wind in a nonuniform, coronal hole-like ambient atmosphere. Our simulations confirm that the jet is initiated by the onset of a kink-like instability of the internal closed field, which induces a burst of reconnection between the closed and external open field, launching a helical jet. Our new results demonstrate that the jet propagation is sustained through the outer corona, in the form of a traveling nonlinear Alfven wave front trailed by slower-moving plasma density enhancements that are compressed and accelerated by the wave. This finding agrees well with observations of white-light coronal-hole jets, and can explain microstreams and torsional Alfven waves detected in situ in the solar wind. We also use our numerical results to deduce scaling relationships between properties of the coronal source region and the characteristics of the resulting jet, which can be tested against observations.

Observational Consequences of Coronal Heating Mechanisms

NASA Technical Reports Server (NTRS)

Winebarger, Amy R.; Cirtain, Jonathan C.; Golub, Leon; Kobayashi, Ken

2014-01-01

The coronal heating problem remains unsolved today, 80 years after its discovery, despite 50 years of suborbital and orbital coronal observatories. Tens of theoretical coronal heating mechanisms have been suggested, but only a few have been able to be ruled out. In this talk, we will explore the reasons for the slow progress and discuss the measurements that will be needed for potential breakthrough, including imaging the solar corona at small spatial scales, measuring the chromospheric magnetic fields, and detecting the presence of high temperature, low emission measure plasma. We will discuss three sounding rocket instruments developed to make these measurements: the High resolution Resolution Coronal Imager (Hi-C), the Chromospheric Lyman-Alpha Spectropolarimeter (CLASP), and the Marshall Grazing Incidence X-ray Spectrometer (MaGIXS).

New Instruments to Isolate the Coronal Heating Mechanism

NASA Technical Reports Server (NTRS)

Winebarger, Amy

2014-01-01

The coronal heating problem remains unsolved today, 80 years after its discovery, despite 50 years of suborbital and orbital coronal observatories. Tens of theoretical coronal heating mechanisms have been suggested, but only a few have been able to be ruled out. In this talk, we will explore the reasons for the slow progress and discuss the measurements that will be needed for potential breakthrough, including imaging the solar corona at small spatial scales, measuring the chromospheric magnetic fields, and detecting the presence of high temperature, low-emission measure plasma. We will discuss three sounding rocket instruments developed to make these measurements: the High-resolution Resolution Coronal Imager (Hi-C), the Chromospheric Lyman-Alpha Spectropolarimeter (CLASP), and the Marshall Grazing Incidence X-ray Spectrometer (MaGIXS).

Usefulness of the dynamic gadolinium-enhanced magnetic resonance imaging with simultaneous acquisition of coronal and sagittal planes for detection of pituitary microadenomas.

PubMed

Lee, Han Bee; Kim, Sung Tae; Kim, Hyung-Jin; Kim, Keon Ha; Jeon, Pyoung; Byun, Hong Sik; Choi, Jin Wook

2012-03-01

Does dynamic gadolinium-enhanced imaging with simultaneous acquisition of coronal and sagittal planes improve diagnostic accuracy of pituitary microadenomas compared with coronal images alone? Fifty-six patients underwent 3-T sella MRI including dynamic simultaneous acquisition of coronal and sagittal planes after gadolinium injection. According to conspicuity, lesions were divided into four scores (0, no; 1, possible; 2, probable; 3, definite delayed enhancing lesion). Additional information on supplementary sagittal images compared with coronal ones was evaluated with a 4-point score (0, no; 1, possible; 2, probable; 3, definite additional information). Accuracy of tumour detection was calculated. Average scores for lesion detection of a combination of two planes, coronal, and sagittal images were 2.59, 2.32, and 2.18. 6/10 lesions negative on coronal images were detected on sagittal ones. Accuracy of a combination of two planes, of coronal and of sagittal images was 92.86%, 82.14% and 75%. Six patients had probable or definite additional information on supplementary sagittal images compared with coronal ones alone (10.71%). Dynamic MRI with combined coronal and sagittal planes was more accurate for detection of pituitary microadenomas than routinely used coronal images. Simultaneous dynamic enhanced acquisition can make study time fast and costs low. We present a new dynamic MRI technique for evaluating pituitary microadenomas • This technique provides simultaneous acquisition of contrast enhanced coronal and sagittal images. • This technique makes the diagnosis more accurate and reduces the examination time. • Such MR imaging only requires one single bolus of contrast agent.

Coronal energy distribution and X-ray activity in the small scale magnetic field of the quiet sun

NASA Technical Reports Server (NTRS)

Habbal, S. R.

1992-01-01

The energy distribution in the small-scale magnetic field that pervades the solar surface, and its relationship to X-ray/coronal activity are discussed. The observed emission from the small scale structures, at temperatures characteristic of the chromosphere, transition region and corona, emanates from the boundaries of supergranular cells, within coronal bright points. This emission is characterized by a strong temporal and spatial variability with no definite pattern. The analysis of simultaneous, multiwavelength EUV observations shows that the spatial density of the enhanced as well as variable emission from the small scale structures exhibits a pronounced temperature dependence with significant maxima at 100,000 and 1,000,000 K. Within the limits of the spatial (1-5 arcsec) and temporal (1-5 min) resolution of data available at present, the observed variability in the small scale structure cannot account for the coroal heating of the quiet sun. The characteristics of their emission are more likely to be an indicator of the coronal heating mechanisms.

Analysis of Solar Coronal Holes with Synoptic Magnetogram Data

NASA Astrophysics Data System (ADS)

Canner, A.; Kim, T. K.; Pogorelov, N.; Yalim, M. S.

2017-12-01

Coronal holes are regions in which the magnetic field of the Sun is open with high magnetic flux and low plasma density. Because of the low plasma beta in these regions, the open field lines transport plasma from the Sun throughout the heliosphere. Coronal hole area is closely related to the expansion factor of the magnetic flux tube, as demonstrated by Tokumaru et al. (2017). Following the approach of Tokumaru et al. (2017), we employ a potential field source surface model to identify the open field regions on the photosphere and estimate the area and expansion factor for each coronal hole. While Tokumaru et al. (2017) analyzed synoptic maps from Kitt Peak National Observatory for the period 1995-2011, we use different magnetograph observations with higher spatial resolution (e.g., SOHO-MDI) for the same time period. We compare the coronal hole area - expansion factor relationship with the original results of Tokumaru et al (2017). This work was supported by the NSF-funded Research Experience for Undergraduates program "Solar and Heliospheric Physics at UAH and MSFC" run by the University of Alabama in Huntsville in partnership with the Marshall Space Flight Center through grant AGS-1460767.

Thermal stability of static coronal loops: Part 1: Effects of boundary conditions

NASA Technical Reports Server (NTRS)

Antiochos, S. K.; Shoub, E. C.; An, C. H.; Emslie, A. G.

1985-01-01

The linear stability of static coronal-loop models undergoing thermal perturbations was investigated. The effect of conditions at the loop base on the stability properties of the models was considered in detail. The question of appropriate boundary conditions at the loop base was considered and it was concluded that the most physical assumptions are that the temperature and density (or pressure) perturbations vanish there. However, if the base is taken to be sufficiently deep in the chromosphere, either several chromospheric scale heights or several coronal loop lengths in depth, then the effect of the boundary conditions on loop stability becomes negligible so that all physically acceptable conditions are equally appropriate. For example, one could as well assume that the velocity vanishes at the base. The growth rates and eigenmodes of static models in which gravity is neglected and in which the coronal heating is a relatively simple function, either constant per-unit mass or per-unit volume were calculated. It was found that all such models are unstable with a growth rate of the order of the coronal cooling time. The physical implications of these results for the solar corona and transition region are discussed.

Loop models of low coronal structures observed by the Normal Incidence X-Ray Telescope (NIXT)

NASA Technical Reports Server (NTRS)

Peres, G.; Reale, F.; Golub, L.

1994-01-01

The X-ray pictures obtained with the Normal Incidence X-Ray Telescope (NIXT), apart from the ubiquitous coronal loops well known from previous X-ray observations, show a new and peculiar morphology: in many active regions there are wide and apparently low-lying areas of intense emission which resemble H alpha plages. By means of hydrostatic models of coronal arches, we analyze the distribution of temperature, density, emission measure, and plasma emissivity in the spectral band to which NIXT is sensitive, and we show that the above morphology can be explained by the characteristics of high pressure loops having a thin region of high surface brightness at the base. We therefore propose that this finding might help to identify high-pressure X-ray emitting coronal regions in NIXT images, and it is in principle applicable to any imaging instrument which has high sensitivity to 10(exp 4) - 10(exp 6) K plasma within a narrow coronal-temperature passband. As a more general result of this study, we propose that the comparison of NIXT observations with models of stationary loops might provide a new diagnostic: the determination of the loop plasma pressure from measurements of brightness distribution along the loop.

Level-dependent coronal and axial moment-rotation corridors of degeneration-free cervical spines in lateral flexion.

PubMed

Yoganandan, Narayan; Pintar, Frank A; Stemper, Brian D; Wolfla, Christopher E; Shender, Barry S; Paskoff, Glenn

2007-05-01

Aging, trauma, or degeneration can affect intervertebral kinematics. While in vivo studies can determine motions, moments are not easily quantified. Previous in vitro studies on the cervical spine have largely used specimens from older individuals with varying levels of degeneration and have shown that moment-rotation responses under lateral bending do not vary significantly by spinal level. The objective of the present in vitro biomechanical study was, therefore, to determine the coronal and axial moment-rotation responses of degeneration-free, normal, intact human cadaveric cervicothoracic spinal columns under the lateral bending mode. Nine human cadaveric cervical columns from C2 to T1 were fixed at both ends. The donors had ranged from twenty-three to forty-four years old (mean, thirty-four years) at the time of death. Retroreflective targets were inserted into each vertebra to obtain rotational kinematics in the coronal and axial planes. The specimens were subjected to pure lateral bending moment with use of established techniques. The range-of-motion and neutral zone metrics for the coronal and axial rotation components were determined at each level of the spinal column and were evaluated statistically. Statistical analysis indicated that the two metrics were level-dependent (p < 0.05). Coronal motions were significantly greater (p < 0.05) than axial motions. Moment-rotation responses were nonlinear for both coronal and axial rotation components under lateral bending moments. Each segmental curve for both rotation components was well represented by a logarithmic function (R(2) > 0.95). Range-of-motion metrics compared favorably with those of in vivo investigations. Coronal and axial motions of degeneration-free cervical spinal columns under lateral bending showed substantially different level-dependent responses. The presentation of moment-rotation corridors for both metrics forms a normative dataset for the degeneration-free cervical spines.

ARE THE FAINT STRUCTURES AHEAD OF SOLAR CORONAL MASS EJECTIONS REAL SIGNATURES OF DRIVEN SHOCKS?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jae-Ok; Moon, Y.-J.; Lee, Kangjin

2014-11-20

Recently, several studies have assumed that the faint structures ahead of coronal mass ejections (CMEs) are caused by CME-driven shocks. In this study, we have conducted a statistical investigation to determine whether or not the appearance of such faint structures depends on CME speeds. For this purpose, we use 127 Solar and Heliospheric Observatory/Large Angle Spectroscopic COronagraph (LASCO) front-side halo (partial and full) CMEs near the limb from 1997 to 2011. We classify these CMEs into two groups by visual inspection of CMEs in the LASCO-C2 field of view: Group 1 has the faint structure ahead of a CME andmore » Group 2 does not have such a structure. We find the following results. (1) Eighty-seven CMEs belong to Group 1 and 40 CMEs belong to Group 2. (2) Group 1 events have much higher speeds (average = 1230 km s{sup –1} and median = 1199 km s{sup –1}) than Group 2 events (average = 598 km s{sup –1} and median = 518 km s{sup –1}). (3) The fraction of CMEs with faint structures strongly depends on CME speeds (V): 0.93 (50/54) for fast CMEs with V ≥ 1000 km s{sup –1}, 0.65 (34/52) for intermediate CMEs with 500 km s{sup –1} ≤ V < 1000 km s{sup –1}, and 0.14 (3/21) for slow CMEs with V < 500 km s{sup –1}. We also find that the fraction of CMEs with deca-hecto metric type II radio bursts is consistent with the above tendency. Our results indicate that the observed faint structures ahead of fast CMEs are most likely an enhanced density manifestation of CME-driven shocks.« less

Extension of Coronal Structure Into Interplanetary Space

NASA Technical Reports Server (NTRS)

Woo, Richard; Habbal, Shadia Rifai

1996-01-01

The evolution of the solar corona and its imprint on the solar wind is investigated by comparing Ulysses radio occultation measurements of path-integrated electron density and density fluctuations in the heliocentric distance range of 21-32R(sub o) with simultaneous measurements of the solasr corona by the HAO Mauna Loa K-coronameter.

Classification and Physical parameters EUV coronal jets with STEREO/SECCHI.

NASA Astrophysics Data System (ADS)

Nistico, Giuseppe; Bothmer, Volker; Patsourakos, Spiro; Zimbardo, Gaetano

In this work we present observations of EUV coronal jets, detected with the SECCHI (Sun Earth Connection Coronal and Heliospheric Investigation) imaging suites of the two STEREO spacecraft. Starting from catalogues of polar and equatorial coronal hole jets (Nistico' et al., Solar Phys., 259, 87, 2009; Ann. Geophys. in press), identified from simultaneous EUV and white-light coronagraph observations, taken during the time period March 2007 to April 2008 when solar activity was at minimum, we perfom a detailed study of some events. A basic char-acterisation of the magnetic morphology and identification of the presence of helical structure were established with respect to recently proposed models for their origin and temporal evo-lution. A classification of the events with respect to previous jet studies shows that amongst the 79 events, identified into polar coronal holes, there were 37 Eiffel tower -type jet events commonly interpreted as a small-scale ( 35 arcsec) magnetic bipole reconnecting with the ambi-ent unipolar open coronal magnetic fields at its looptops, 12 lambda-type jet events commonly interpreted as reconnection with the ambient field happening at the bipoles footpoints. Five events were termed micro-CME type jet events because they resembled classical three-part structured coronal mass ejections (CMEs) but on much smaller scales. The remainig 25 cases could not be uniquely classified. Thirty-one of the total number of events exhibited a helical magnetic field structure, indicative for a torsional motion of the jet around its axis of propaga-tion. The jet events are found to be also present in equatorial coronal holes. We also present the 3-D reconstruction, temperature, velocity, and density measurements of a number of jets during their evolution.

A Bayesian Approach to Period Searching in Solar Coronal Loops

NASA Astrophysics Data System (ADS)

Scherrer, Bryan; McKenzie, David

2017-03-01

We have applied a Bayesian generalized Lomb-Scargle period searching algorithm to movies of coronal loop images obtained with the Hinode X-ray Telescope (XRT) to search for evidence of periodicities that would indicate resonant heating of the loops. The algorithm makes as its only assumption that there is a single sinusoidal signal within each light curve of the data. Both the amplitudes and noise are taken as free parameters. It is argued that this procedure should be used alongside Fourier and wavelet analyses to more accurately extract periodic intensity modulations in coronal loops. The data analyzed are from XRT Observation Program #129C: “MHD Wave Heating (Thin Filters),” which occurred during 2006 November 13 and focused on active region 10293, which included coronal loops. The first data set spans approximately 10 min with an average cadence of 2 s, 2″ per pixel resolution, and used the Al-mesh analysis filter. The second data set spans approximately 4 min with a 3 s average cadence, 1″ per pixel resolution, and used the Al-poly analysis filter. The final data set spans approximately 22 min at a 6 s average cadence, and used the Al-poly analysis filter. In total, 55 periods of sinusoidal coronal loop oscillations between 5.5 and 59.6 s are discussed, supporting proposals in the literature that resonant absorption of magnetic waves is a viable mechanism for depositing energy in the corona.

A Bayesian Approach to Period Searching in Solar Coronal Loops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scherrer, Bryan; McKenzie, David

2017-03-01

We have applied a Bayesian generalized Lomb–Scargle period searching algorithm to movies of coronal loop images obtained with the Hinode X-ray Telescope (XRT) to search for evidence of periodicities that would indicate resonant heating of the loops. The algorithm makes as its only assumption that there is a single sinusoidal signal within each light curve of the data. Both the amplitudes and noise are taken as free parameters. It is argued that this procedure should be used alongside Fourier and wavelet analyses to more accurately extract periodic intensity modulations in coronal loops. The data analyzed are from XRT Observation Programmore » 129C: “MHD Wave Heating (Thin Filters),” which occurred during 2006 November 13 and focused on active region 10293, which included coronal loops. The first data set spans approximately 10 min with an average cadence of 2 s, 2″ per pixel resolution, and used the Al-mesh analysis filter. The second data set spans approximately 4 min with a 3 s average cadence, 1″ per pixel resolution, and used the Al-poly analysis filter. The final data set spans approximately 22 min at a 6 s average cadence, and used the Al-poly analysis filter. In total, 55 periods of sinusoidal coronal loop oscillations between 5.5 and 59.6 s are discussed, supporting proposals in the literature that resonant absorption of magnetic waves is a viable mechanism for depositing energy in the corona.« less

Electrons in the solar corona. III - Coronal streamers analysis from balloon-borne coronagraph

NASA Astrophysics Data System (ADS)

Dollfus, A.; Mouradian, Z.

1981-03-01

The solar corona is discussed on the basis of observations made during a 5-hour period in France in September 1971. Using a balloon at an altitude of 32,000 m, the solar corona was cinematographed from 2 to 5 solar radii with an externally occulted coronagraph. It is noted that motions in coronal features, when they occur, exhibit deformations of structures with velocities not exceeding a few tens of km/s. Several streamers were often involved simultaneously; these variations are compatible with magnetic changes or sudden reorganizations of lines of forces. Intensity and polarization measurements are shown to give the electron density with height in the quiet corona above the equator. Three-dimensional structures and localizations of the streamers are deduced from combined photometry, polarimetry, and ground-based K coronametry.

Type 2 and type 3 burst theory

NASA Technical Reports Server (NTRS)

Smith, D. F.

1973-01-01

The present state of the theory of type 3 bursts is reviewed by dividing the problem into the exciting agency, radiation source, and propagation of radiation between the source and the observer. In-situ measurements indicate that the excitors are electron streams of energy about 40 keV which are continuously relaxing. An investigation of neutralization of an electron stream indicates that n sub s is much less than 100,000 n sub e, where n sub s is the stream density and n sub e the coronal electron density. In situ observations are consistent with this result. An analysis of propagation of electrons in the current sheets of coronal streamers shows that such propagation at heights greater than 1 solar radius is impossible. The mechanisms for radiation are reviewed; it is shown that fundamental radiation at high frequencies (approximately 100 MHz) is highly beamed in the radial direction and that near the earth second harmonic radiation must be dominant. Because of beaming of the fundamental at high frequencies, it can often be quite weak near the limb so that the second harmonic is dominant. In considering propagation to the observer, the results of scattering of radiation are discussed. The present state of the theory of type 2 bursts is reviewed in the same manner as type 3 bursts.

Investigation of the Large Scale Evolution and Topology of Coronal Mass Ejections in the Solar Wind

NASA Technical Reports Server (NTRS)

Riley, Pete

2001-01-01

This investigation is concerned with the large-scale evolution and topology of coronal mass ejections (CMEs) in the solar wind. During the course of this three-year investigation, we have undertaken a number of studies that are discussed in more detail in this report. For example, we conducted an analysis of all CMEs observed by the Ulysses spacecraft during its in-ecliptic phase between 1 and 5 AU. In addition to studying the properties of the ejecta, we also analyzed the shocks that could be unambiguously associated with the fast CMEs. We also analyzed a series of 'density holes' observed in the solar wind that bear many similarities with CMEs. To complement this analysis, we conducted a series of 1-D and 2 1/2-D fluid, MHD, and hybrid simulations to address a number of specific issues related to CME evolution in the solar wind. For example, we used fluid simulations to address the interpretation of negative electron temperature-density relationships often observed within CME/cloud intervals. As part of this investigation, a number of fruitful international collaborations were forged. Finally, the results of this work were presented at nine scientific meetings and communicated in eight scientific, refereed papers.

Anterior lumbar instrumentation improves correction of severe lumbar Lenke C curves in double major idiopathic scoliosis

PubMed Central

Yeon, Howard B.; Weinberg, Jacob; Arlet, Vincent; Ouelett, Jean A.

2007-01-01

Fifteen skeletally immature patients with double major adolescent idiopathic scoliosis with large lumbar curves and notable L4 and L5 coronal plane obliquity were retrospectively studied. Seven patients who underwent anterior release and fusion of the lumbar curve with segmental anterior instrumentation and subsequent posterior instrumentation ending at L3 were compared with eight patients treated with anterior release and fusion without anterior instrumentation followed by posterior instrumentation to L3 or L4. At 4.5 years follow-up (range 2.5–7 years), curve correction, coronal balance and fusion rate were not statistically different between the two groups; however, the group with anterior instrumentation had improved coronal plane, near normalangulation in the distal unfused segment compared with the group without anterior instrumentation. In cases involving severe lumbar curvatures in the context of double major scoliosis, when as a first stage anterior release is chosen, the addition of instrumentation appears to restore normal coronal alignment of the distal unfused lumbar segment, and may in certain cases save a level compared with traditional fusions to L4. PMID:17464517

Pre-flare coronal dimmings

NASA Astrophysics Data System (ADS)

Zhang, Q. M.; Su, Y. N.; Ji, H. S.

2017-02-01

Context. Coronal dimmings are regions of decreased extreme-ultravoilet (EUV) and/or X-ray (originally Skylab, then Yohkoh/SXT) intensities, which are often associated with flares and coronal mass ejections (CMEs). The large-scale impulsive dimmings have been thoroughly observed and investigated. The pre-flare dimmings before the flare impulsive phase, however, have rarely been studied in detail. Aims: We focus on the pre-flare coronal dimmings. We report our multiwavelength observations of the GOES X1.6 solar flare and the accompanying halo CME that was produced by the eruption of a sigmoidal magnetic flux rope (MFR) in NOAA active region (AR) 12158 on 2014 September 10. Methods: The eruption was observed by the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamic Observatory (SDO). The photospheric line-of-sight magnetograms were observed by the Helioseismic and Magnetic Imager (HMI) on board SDO. The soft X-ray (SXR) fluxes were recorded by the GOES spacecraft. The halo CME was observed by the white-light coronagraphs of the Large Angle Spectroscopic Coronagraph (LASCO) on board SOHO. Results: About 96 min before the onset of the flare/CME, narrow pre-flare coronal dimmings appeared at the two ends of the twisted MFR. They extended very slowly, with their intensities decreasing with time, while their apparent widths (8-9 Mm) continued to be nearly constant. During the impulsive and decay phases of flare, typical fan-like twin dimmings appeared and expanded, with a much larger extent and lower intensities than the pre-flare dimmings. The percentage of the 171 Å intensity decrease reaches 40%. The pre-flare dimmings are most striking in 171, 193, and 211 Å with formation temperatures of 0.6-2.5 MK. The northern part of the pre-flare dimmings could also be recognized in 131 and 335 Å. Conclusions: To our knowledge, this is the first detailed study of pre-flare coronal dimmings; they can be explained by density depletion as a result of the gradual expansion of the coronal loop system surrounding the MFR during the slow rise of the MFR. Movie associated to Fig. 5 is available at http://www.aanda.org

Vertebral Derotation by Vertebral Column Manipulator Improves Postoperative Radiographs Outcomes of Lenke 5C Patients for Follow-up of Minimum 2 Years.

PubMed

Huang, Zifang; Wang, Qifei; Yang, Junlin; Yang, Jingfan; Li, Fobao

2016-04-01

This was a retrospective study. The aim of this study was to compare radiographic outcomes of Lenke 5C adolescent idiopathic scoliosis (AIS) patients treated by vertebral column manipulator (VCM) or simple rod derotation (SRD) maneuver. The direct vertebral rotation (DVR) technique has demonstrated better rotational and coronal correction than SRD, but clinical radiographic outcomes for Lenke 5C AIS following DVR using a VCM derotational device have not been described. A retrospective study was carried out in 39 Lenke 5C AIS patients treated by VCM (n=20) or SRD (n=19) techniques between April 2008 and June 2011. All patients had complete clinical record and radiographic data. Nine radiographic variables were collected and compared at 3 time points (preoperative, immediate postoperative, and minimum 2-year follow-up) between both groups. Scoliosis was successfully corrected in both groups. All patients obtained good coronal and sagittal balance, and no severe complications occurred. The postoperative apical rotation corrective rate of the VCM and SRD groups were 55.1% and 25.5%, respectively (P < 0.05). Lowest instrumented vertebra and stable vertebra (LIV-SV) was statistically significant between the VCM and SRD groups, the mean values were 1.2 ± 0.4 level and 0.7 ± 0.5 level (P < 0.05). The main curve corrective rates and LIV-tilt angle correction rates were not significantly different between groups, but it showed a spontaneous correction for the coronal LIV-tilt angle for both groups at the last follow-up. VCM improved postoperative apical axial rotational correction and lessened the lumbar fusion segment compared with the SRD technique, which might have a potential trend to reserve lumbar mobility.

Image-based reconstruction of the Newtonian dynamics of solar coronal ejecta

NASA Astrophysics Data System (ADS)

Uritsky, Vadim M.; Thompson, Barbara J.

2016-10-01

We present a new methodology for analyzing rising and falling dynamics of unstable coronal material as represented by high-cadence SDO AIA images. The technique involves an adaptive spatiotemporal tracking of propagating intensity gradients and their characterization in terms of time-evolving areas swept out by the position vector originated from the Sun disk center. The measured values of the areal velocity and acceleration are used to obtain quantitative information on the angular momentum and acceleration along the paths of the rising and falling coronal plasma. In the absence of other forces, solar gravitation results in purely ballistic motions consistent with the Kepler's second law; non-central forces such as the Lorentz force introduce non-zero torques resulting in more complex motions. The developed algorithms enable direct evaluation of the line-of-sight component of the net torque applied to a unit mass of the ejected coronal material which is proportional to the image-plane projection of the observed areal acceleration. The current implementation of the method cannot reliably distinguish torque modulations caused by the coronal force field from those imposed by abrupt changes of plasma mass density and nontrivial projection effects. However, it can provide valid observational constraints on the evolution of large-scale unstable magnetic topologies driving major solar-coronal eruptions as demonstrated in the related talk by B. Thompson et al.

IfA Catalogs of Solar Data Products

NASA Astrophysics Data System (ADS)

Habbal, Shadia R.; Scholl, I.; Morgan, H.

2009-05-01

This paper presents a new set of online catalogs of solar data products. The IfA Catalogs of Solar Data Products were developed to enhance the scientific output of coronal images acquired from ground and space, starting with the SoHO era. Image processing tools have played a significant role in the production of these catalogs [Morgan et al. 2006, 2008, Scholl and Habbal 2008]. Two catalogs are currently available at http://alshamess.ifa.hawaii.edu/ : 1) Catalog of daily coronal images: One coronal image per day from EIT, MLSO and LASCO/C2 and C3 have been processed using the Normalizing Radial-Graded-Filter (NRGF) image processing tool. These images are available individually or as composite images. 2) Catalog of LASCO data: The whole LASCO dataset has been re-processed using the same method. The user can search files by dates and instruments, and images can be retrieved as JPEG or FITS files. An option to make on-line GIF movies from selected images is also available. In addition, the LASCO data set can be searched from existing CME catalogs (CDAW and Cactus). By browsing one of the two CME catalogs, the user can refine the query and access LASCO data covering the time frame of a CME. The catalogs will be continually updated as more data become publicly available.

Loop Evolution Observed with AIA and Hi-C

NASA Technical Reports Server (NTRS)

Mulu-Moore, Fana; Winebarger, Amy R.; Cirtain, Jonathan W.; Kobayashi, Ken; Korreck, Kelly E.; Golub, Leon; Kuzin, Sergei; Walsh, Robert William; DeForest, Craig E.; De Pontieu, Bart;

Spatial evolution of 26-day recurrent galactic cosmic ray decreases: Correlated Ulysses COSPIN/KET and SOHO COSTEP observations

NASA Technical Reports Server (NTRS)

Heber, B.; Bothmer, V.; Droege, W.; Kunow, H.; Mueller-Mellin, R.; Posner, A.; Ferrando, P.; Raviart, A.; Paizis, C.; McComas, D.;

RECONNECTION-DRIVEN CORONAL-HOLE JETS WITH GRAVITY AND SOLAR WIND

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karpen, J. T.; DeVore, C. R.; Antiochos, S. K.

Coronal-hole jets occur ubiquitously in the Sun's coronal holes, at EUV and X-ray bright points associated with intrusions of minority magnetic polarity. The embedded-bipole model for these jets posits that they are driven by explosive, fast reconnection between the stressed closed field of the embedded bipole and the open field of the surrounding coronal hole. Previous numerical studies in Cartesian geometry, assuming uniform ambient magnetic field and plasma while neglecting gravity and solar wind, demonstrated that the model is robust and can produce jet-like events in simple configurations. We have extended these investigations by including spherical geometry, gravity, and solarmore » wind in a nonuniform, coronal hole-like ambient atmosphere. Our simulations confirm that the jet is initiated by the onset of a kink-like instability of the internal closed field, which induces a burst of reconnection between the closed and external open field, launching a helical jet. Our new results demonstrate that the jet propagation is sustained through the outer corona, in the form of a traveling nonlinear Alfvén wave front trailed by slower-moving plasma density enhancements that are compressed and accelerated by the wave. This finding agrees well with observations of white-light coronal-hole jets, and can explain microstreams and torsional Alfvén waves detected in situ in the solar wind. We also use our numerical results to deduce scaling relationships between properties of the coronal source region and the characteristics of the resulting jet, which can be tested against observations.« less

Two Coronal Holes on the Sun Viewed by SDO

NASA Image and Video Library

2015-03-17

NASA’s Solar Dynamics Observatory, or SDO, captured this solar image on March 16, 2015, which clearly shows two dark patches, known as coronal holes. The larger coronal hole of the two, near the southern pole, covers an estimated 6- to 8-percent of the total solar surface. While that may not sound significant, it is one of the largest polar holes scientists have observed in decades. The smaller coronal hole, towards the opposite pole, is long and narrow. It covers about 3.8 billion square miles on the sun - only about 0.16-percent of the solar surface. Coronal holes are lower density and temperature regions of the sun’s outer atmosphere, known as the corona. Coronal holes can be a source of fast solar wind of solar particles that envelop the Earth. The magnetic field in these regions extends far out into space rather than quickly looping back into the sun’s surface. Magnetic fields that loop up and back down to the surface can be seen as arcs in non-coronal hole regions of the image, including over the lower right horizon. The bright active region on the lower right quadrant is the same region that produced solar flares last week. Credit: NASA/Goddard/SDO NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Stellar winds and coronae of low-mass Population II/III stars

NASA Astrophysics Data System (ADS)

Suzuki, Takeru K.

2018-06-01

We investigated stellar winds from zero-/low-metallicity low-mass stars by magnetohydrodynamical simulations for stellar winds driven by Alfvén waves from stars with mass M = (0.6-0.8) M⊙ and metallicity Z = (0-1) Z⊙, where M⊙ and Z⊙ are the solar mass and metallicity, respectively. Alfvénic waves, which are excited by the surface convection, travel upward from the photosphere and heat up the corona by their dissipation. For lower Z, denser gas can be heated up to the coronal temperature because of the inefficient radiation cooling. The coronal density of Population II/III stars with Z ≤ 0.01 Z⊙ is one to two orders of magnitude larger than that of a solar-metallicity star with the same mass, and as a result, the mass loss rate, \\dot{M}, is 4.5-20 times larger. This indicates that metal accretion on low-mass Pop. III stars is negligible. The soft X-ray flux of the Pop. II/III stars is also expected to be ˜1-30 times larger than that of a solar-metallicity counterpart owing to the larger coronal density, even though the radiation cooling efficiency is smaller. A larger fraction of the input Alfvénic wave energy is transmitted to the corona in low-Z stars because they avoid severe reflection owing to the smaller density difference between the photosphere and the corona. Therefore, a larger fraction is converted to the thermal energy of the corona and the kinetic energy of the stellar wind. From this energetics argument, we finally derived a scaling of \\dot{M} as \\dot{M}∝ L R_{\\star }^{11/9} M_{\\star }^{-10/9} T_eff^{11/2}[\\max (Z/Z_{⊙},0.01)]^{-1/5}, where L, R⋆, and Teff are the stellar luminosity, radius, and effective temperature, respectively.

Stellar winds and coronae of low-mass Population II/III stars

NASA Astrophysics Data System (ADS)

Suzuki, Takeru K.

2018-04-01

We investigated stellar winds from zero-/low-metallicity low-mass stars by magnetohydrodynamical simulations for stellar winds driven by Alfvén waves from stars with mass M = (0.6-0.8) M⊙ and metallicity Z = (0-1) Z⊙, where M⊙ and Z⊙ are the solar mass and metallicity, respectively. Alfvénic waves, which are excited by the surface convection, travel upward from the photosphere and heat up the corona by their dissipation. For lower Z, denser gas can be heated up to the coronal temperature because of the inefficient radiation cooling. The coronal density of Population II/III stars with Z ≤ 0.01 Z⊙ is one to two orders of magnitude larger than that of a solar-metallicity star with the same mass, and as a result, the mass loss rate, \\dot{M}, is 4.5-20 times larger. This indicates that metal accretion on low-mass Pop. III stars is negligible. The soft X-ray flux of the Pop. II/III stars is also expected to be ˜1-30 times larger than that of a solar-metallicity counterpart owing to the larger coronal density, even though the radiation cooling efficiency is smaller. A larger fraction of the input Alfvénic wave energy is transmitted to the corona in low-Z stars because they avoid severe reflection owing to the smaller density difference between the photosphere and the corona. Therefore, a larger fraction is converted to the thermal energy of the corona and the kinetic energy of the stellar wind. From this energetics argument, we finally derived a scaling of \\dot{M} as \\dot{M}∝ L R_{\\star }^{11/9} M_{\\star }^{-10/9} T_eff^{11/2}[\\max (Z/Z_{⊙},0.01)]^{-1/5}, where L, R⋆, and Teff are the stellar luminosity, radius, and effective temperature, respectively.

Physical Properties of the SKYLAB North Polar Coronal Hole with an Extended Base and its MHD Self-Consistent Modelling

NASA Astrophysics Data System (ADS)

Bravo, S.; Ocania, G.

1991-04-01

RESUMEN Con base en las observaciones del Skylab del Sol en rayos X que permitieron r la forma de la frontera del hoyo coronal del polo norte y en las observaciones de l 'z que permitieron derivar un perfil de densidad para el flujo de viento solar (IC ese hoyo, Murno yjackson (1977) concluyeron que se requiere una adici6n t l clc energfa al flujo hasta al menos 5 R8. En este trabajo, recalculamos los perfiles de y de temperatura para el mismo hoyo pero considerando una frontera Cs mas ancha en la base, de acuerdo con las observaciones del coron6metro-K del IIAO, los espectroheliogramas en EUV del OSO-7 y las fotografias de la corona solar cerca de los 4 E)()O A. Se tomaron tambien las incertidumbres en el perfil de densidad electr6nica inl & a las observaciones de luz blanca y se consideraron diversos valores posibles dCl fl 'jo (lC masa 1 UA. Encontramos que las diferencias introducidas no son suficientes par clcsc' la necesidad de una energetizaci6n extensa del viento solar, pero una dC las s posibles muestra una concordancia muy buena con el modelado MHD (l( l flujo con el unico t6rmino adicional de la fuerza de Lorentz en la ecuaci6n de # (). ABSTRACT Based on the near to the Sun boundary of the Skylab north polar coroi ' l estimated from the AS & E X-ray photographs and on the density profile fi-C)I white light data, Munro and Jackson (1977) concluded that substantial energy the solar wind flux is required up to at least 5 Rs. In this paper we recalculate `eloci y and temperature profiles for the same hole but considering a different bo ' ry for flux tube which is larger at its base, according to the HAO K- obser"' (i()I0 , the OSO-7 EUV spectroheliograms and pictures of the solar 4500 A. è take into account the uncertainties inherent in the white light observations () electron density profile and consider different possible values of the solar I .' fltix at 1 AU. We that the differences introduced are not sufficient to discard ii y of an extended energetization of the wind, one of the possibilities allowed for fltix the observational uncertailities shows a very good agreement wi4 an NI Ill) seli'consistent modelling with the only additional term of the Lorentz force in the iiii equation. Key words: SUN-CORONA

Current systems of coronal loops in 3D MHD simulations

NASA Astrophysics Data System (ADS)

Warnecke, J.; Chen, F.; Bingert, S.; Peter, H.

2017-11-01

Aims: We study the magnetic field and current structure associated with a coronal loop. Through this we investigate to what extent the assumptions of a force-free magnetic field break down and where they might be justified. Methods: We analyze a three-dimensional (3D) magnetohydrodynamic (MHD) model of the solar corona in an emerging active region with the focus on the structure of the forming coronal loops. The lower boundary of this simulation is taken from a model of an emerging active region. As a consequence of the emerging magnetic flux and the horizontal motions at the surface a coronal loop forms self-consistently. We investigate the current density along magnetic field lines inside (and outside) this loop and study the magnetic and plasma properties in and around this loop. The loop is defined as the bundle of field lines that coincides with enhanced emission in extreme UV. Results: We find that the total current along the emerging loop changes its sign from being antiparallel to parallel to the magnetic field. This is caused by the inclination of the loop together with the footpoint motion. Around the loop, the currents form a complex non-force-free helical structure. This is directly related to a bipolar current structure at the loop footpoints at the base of the corona and a local reduction of the background magnetic field (I.e., outside the loop) caused by the plasma flow into and along the loop. Furthermore, the locally reduced magnetic pressure in the loop allows the loop to sustain a higher density, which is crucial for the emission in extreme UV. The action of the flow on the magnetic field hosting the loop turns out to also be responsible for the observed squashing of the loop. Conclusions: The complex magnetic field and current system surrounding it can only be modeled in 3D MHD models where the magnetic field has to balance the plasma pressure. A one-dimensional coronal loop model or a force-free extrapolation cannot capture the current system and the complex interaction of the plasma and the magnetic field in the coronal loop, despite the fact that the loop is under low-β conditions.

Comparative phylogeography of two crow species: jungle crow Corvus macrorhynchos and carrion crow Corvus corone.

PubMed

Kryukov, Alexey; Spiridonova, Liudmila; Nakamura, Sumio; Haring, Elisabeth; Suzuki, Hitoshi

2012-08-01

The jungle crow Corvus macrorhynchos Wagler, 1827, and the carrion crow Corvus corone L., 1758, are two closely related species with similar ecological requirements that occupy wide distribution ranges in the Palearctic. We studied patterns of their genetic variation by using sequences of the mitochondrial cytochrome b gene. Corvus macrorhynchos demonstrates a low level of variation and differentiation throughout its range, except for a highly diverged population of Cheju Island (Korea). The haplotype network shows two haplogroups. The island group comprises populations of Sakhalin, Hokkaido, Honshu, and Kyushu, while the haplotypes of Taiwan and Ryukyu Islands proved to be closer to the mainland group, which also includes populations from the Primorye, Khabarovsk, Amur, and Magadan regions in the Russian Far East. This pattern allowed us to develop a phylogeographic hypothesis regarding the two modes of settling of the island populations. Concerning C. corone, the presence of two distinct haplogroups was confirmed within the range of C. c. orientalis. Both haplogroups are found within the same populations in Kamchatka and North Sakhalin, which implies secondary contacts there. Populations of C. corone are found to be rather stable in the western parts of its range, while in the Far East populations experienced recent growth, as was observed for C. macrorhynchos in general. The two species appear to have passed through different evolutionary scenarios.

Mass and energy supply of a cool coronal loop near its apex

NASA Astrophysics Data System (ADS)

Yan, Limei; Peter, Hardi; He, Jiansen; Xia, Lidong; Wang, Linghua

2018-03-01

Context. Different models for the heating of solar corona assume or predict different locations of the energy input: concentrated at the footpoints, at the apex, or uniformly distributed. The brightening of a loop could be due to the increase in electron density ne, the temperature T, or a mixture of both. Aim. We investigate possible reasons for the brightening of a cool loop at transition region temperatures through imaging and spectral observation. Methods: We observed a loop with the Interface Region Imaging Spectrograph (IRIS) and used the slit-jaw images together with spectra taken at a fixed slit position to study the evolution of plasma properties in and below the loop. We used spectra of Si IV, which forms at around 80 000 K in equilibrium, to identify plasma motions and derive electron densities from the ratio of inter-combination lines of O IV. Additional observations from the Solar Dynamics Observatory (SDO) were employed to study the response at coronal temperatures (Atmospheric Imaging Assembly, AIA) and to investigate the surface magnetic field below the loop (Helioseismic and Magnetic Imager, HMI). Results: The loop first appears at transition region temperatures and later also at coronal temperatures, indicating a heating of the plasma in the loop. The appearance of hot plasma in the loop coincides with a possible accelerating upflow seen in Si IV, with the Doppler velocity shifting continuously from -70 km s-1 to -265 km s-1. The 3D magnetic field lines extrapolated from the HMI magnetogram indicate possible magnetic reconnection between small-scale magnetic flux tubes below or near the loop apex. At the same time, an additional intensity enhancement near the loop apex is visible in the IRIS slit-jaw images at 1400 Å. These observations suggest that the loop is probably heated by the interaction between the loop and the upflows, which are accelerated by the magnetic reconnection between small-scale magnetic flux tubes at lower altitudes. Before and after the possible heating phase, the intensity changes in the optically thin (Si IV) and optical thick line (C II) are mainly contributed by the density variation without significant heating. Conclusions: We therefore provide evidence for the heating of an envelope loop that is affected by accelerating upflows, which are probably launched by magnetic reconnection between small-scale magnetic flux tubes underneath the envelope loop. This study emphasizes that in the complex upper atmosphere of the Sun, the dynamics of the 3D coupled magnetic field and flow field plays a key role in thermalizing 1D structures such as coronal loops. An animation associated to Fig. 1 is available at http://https://www.aanda.org

3D MHD MODELING OF TWISTED CORONAL LOOPS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reale, F.; Peres, G.; Orlando, S.

We perform MHD modeling of a single bright coronal loop to include the interaction with a non-uniform magnetic field. The field is stressed by random footpoint rotation in the central region and its energy is dissipated into heating by growing currents through anomalous magnetic diffusivity that switches on in the corona above a current density threshold. We model an entire single magnetic flux tube in the solar atmosphere extending from the high- β chromosphere to the low- β corona through the steep transition region. The magnetic field expands from the chromosphere to the corona. The maximum resolution is ∼30 km.more » We obtain an overall evolution typical of loop models and realistic loop emission in the EUV and X-ray bands. The plasma confined in the flux tube is heated to active region temperatures (∼3 MK) after ∼2/3 hr. Upflows from the chromosphere up to ∼100 km s{sup −1} fill the core of the flux tube to densities above 10{sup 9} cm{sup −3}. More heating is released in the low corona than the high corona and is finely structured both in space and time.« less

Verification of Loop Diagnostics

NASA Technical Reports Server (NTRS)

Winebarger, A.; Lionello, R.; Mok, Y.; Linker, J.; Mikic, Z.

2014-01-01

Many different techniques have been used to characterize the plasma in the solar corona: density-sensitive spectral line ratios are used to infer the density, the evolution of coronal structures in different passbands is used to infer the temperature evolution, and the simultaneous intensities measured in multiple passbands are used to determine the emission measure. All these analysis techniques assume that the intensity of the structures can be isolated through background subtraction. In this paper, we use simulated observations from a 3D hydrodynamic simulation of a coronal active region to verify these diagnostics. The density and temperature from the simulation are used to generate images in several passbands and spectral lines. We identify loop structures in the simulated images and calculate the loop background. We then determine the density, temperature and emission measure distribution as a function of time from the observations and compare with the true temperature and density of the loop. We find that the overall characteristics of the temperature, density, and emission measure are recovered by the analysis methods, but the details of the true temperature and density are not. For instance, the emission measure curves calculated from the simulated observations are much broader than the true emission measure distribution, though the average temperature evolution is similar. These differences are due, in part, to inadequate background subtraction, but also indicate a limitation of the analysis methods.

Interplanetary Coronal Mass Ejection effects on thermospheric density as inferred from International Space Station orbital data

NASA Astrophysics Data System (ADS)

Mendaza, T.; Blanco-Ávalos, J. J.; Martín-Torres, J.

2017-11-01

The solar activity induces long term and short term periodical variations in the dynamics and composition of Earth's atmosphere. The Sun also shows non periodical (i.e., impulsive) activity that reaches the planets orbiting around it. In particular, Interplanetary Coronal Mass Ejections (ICMEs) reach Earth and interact with its magnetosphere and upper neutral atmosphere. Nevertheless, the interaction with the upper atmosphere is not well characterized because of the absence of regular and dedicated in situ measurements at high altitudes; thus, current descriptions of the thermosphere are based on semi empirical models. In this paper, we present the total neutral mass densities of the thermosphere retrieved from the orbital data of the International Space Station (ISS) using the General Perturbation Method, and we applied these densities to routinely compiled trajectories of the ISS in low Earth orbit (LEO). These data are explicitly independent of any atmospheric model. Our density values are consistent with atmospheric models, which demonstrates that our method is reliable for the inference of thermospheric density. We have inferred the thermospheric total neutral density response to impulsive solar activity forcing from 2001 to the end of 2006 and determined how solar events affect this response. Our results reveal that the ISS orbital parameters can be used to infer the thermospheric density and analyze solar effects on the thermosphere.

An in vitro study of coronal leakage after intraradicular preparation of cast-dowel space.

PubMed

Pappen, A F; Bravo, M; Gonzalez-Lopez, S; Gonzalez-Rodriguez, M P

2005-09-01

Coronal leakage can produce contamination of periapical tissues, resulting in endodontic failure. The purpose of this in vitro study was to evaluate the ability of 2 sealers to prevent coronal leakage in canals filled with gutta-percha and prepared for cast dowels but without coronal sealing. The crowns of 60 extracted single-rooted teeth were amputated. The root canals were prepared corono-apically and filled with gutta-percha cones and 1 of 2 different endodontic sealers: a resin-based sealer (AH Plus) and a calcium hydroxide-based sealer (Sealapex). Specimens were then stored in water for 7 days to allow the sealers to set. The specimens were prepared in 1 of 2 ways: no preparation for cast dowel or preparation of cast-dowel space (n=15). External surfaces of the roots were sealed with cyanoacrylate cement. The teeth were thermal cycled at 5 degrees and 55 degrees C in water baths (dwell time=30 seconds) for 500 cycles. Specimens were then submerged in 2% methylene blue colorant for 24 hours. Microleakage was measured according to the percentage of area stained with the colorant. Effects of each factor (cast-dowel preparation and type of sealant) on microleakage were analyzed by the Student t test (alpha=.05). The AH Plus and Sealapex sealers with cast-dowel preparation resulted in significantly (P<.001) more leakage compared to sealers with no dowel preparation. Cast dowel-space preparation had a negative influence on the sealing ability of the remnant root-canal filling material.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sherlock, M.; Brodrick, J. P.; Ridgers, C. P.

Here, we compare the reduced non-local electron transport model developed to Vlasov-Fokker-Planck simulations. Two new test cases are considered: the propagation of a heat wave through a high density region into a lower density gas, and a one-dimensional hohlraum ablation problem. We find that the reduced model reproduces the peak heat flux well in the ablation region but significantly over-predicts the coronal preheat. The suitability of the reduced model for computing non-local transport effects other than thermal conductivity is considered by comparing the computed distribution function to the Vlasov-Fokker-Planck distribution function. It is shown that even when the reduced modelmore » reproduces the correct heat flux, the distribution function is significantly different to the Vlasov-Fokker-Planck prediction. Two simple modifications are considered which improve agreement between models in the coronal region.« less

Spatiotemporal Analysis of Coronal Loops Using Seismology of Damped Kink Oscillations and Forward Modeling of EUV Intensity Profiles

NASA Astrophysics Data System (ADS)

Pascoe, D. J.; Anfinogentov, S. A.; Goddard, C. R.; Nakariakov, V. M.

2018-06-01

The shape of the damping profile of kink oscillations in coronal loops has recently allowed the transverse density profile of the loop to be estimated. This requires accurate measurement of the damping profile that can distinguish the Gaussian and exponential damping regimes, otherwise there are more unknowns than observables. Forward modeling of the transverse intensity profile may also be used to estimate the width of the inhomogeneous layer of a loop, providing an independent estimate of one of these unknowns. We analyze an oscillating loop for which the seismological determination of the transverse structure is inconclusive except when supplemented by additional spatial information from the transverse intensity profile. Our temporal analysis describes the motion of a coronal loop as a kink oscillation damped by resonant absorption, and our spatial analysis is based on forward modeling the transverse EUV intensity profile of the loop under the isothermal and optically thin approximations. We use Bayesian analysis and Markov chain Monte Carlo sampling to apply our spatial and temporal models both individually and simultaneously to our data and compare the results with numerical simulations. Combining the two methods allows both the inhomogeneous layer width and density contrast to be calculated, which is not possible for the same data when each method is applied individually. We demonstrate that the assumption of an exponential damping profile leads to a significantly larger error in the inferred density contrast ratio compared with a Gaussian damping profile.

Measurements of coronal Faraday rotation at 4.6 R {sub ☉}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kooi, Jason E.; Fischer, Patrick D.; Buffo, Jacob J.

2014-03-20

Many competing models for the coronal heating and acceleration mechanisms of the high-speed solar wind depend on the solar magnetic field and plasma structure in the corona within heliocentric distances of 5 R {sub ☉}. We report on sensitive Very Large Array (VLA) full-polarization observations made in 2011 August, at 5.0 and 6.1 GHz (each with a bandwidth of 128 MHz) of the radio galaxy 3C 228 through the solar corona at heliocentric distances of 4.6-5.0 R {sub ☉}. Observations at 5.0 GHz permit measurements deeper in the corona than previous VLA observations at 1.4 and 1.7 GHz. These Faradaymore » rotation observations provide unique information on the magnetic field in this region of the corona. The measured Faraday rotation on this day was lower than our a priori expectations, but we have successfully modeled the measurement in terms of observed properties of the corona on the day of observation. Our data on 3C 228 provide two lines of sight (separated by 46'', 33,000 km in the corona). We detected three periods during which there appeared to be a difference in the Faraday rotation measure between these two closely spaced lines of sight. These measurements (termed differential Faraday rotation) yield an estimate of 2.6-4.1 GA for coronal currents. Our data also allow us to impose upper limits on rotation measure fluctuations caused by coronal waves; the observed upper limits were 3.3 and 6.4 rad m{sup –2} along the two lines of sight. The implications of these results for Joule heating and wave heating are briefly discussed.« less

Measurements of outflow velocities in on-disk plumes from EIS/Hinode observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, Hui; Xia, Lidong; Li, Bo

2014-10-20

The contribution of plumes to the solar wind has been subject to hot debate in the past decades. The EUV Imaging Spectrometer (EIS) on board Hinode provides a unique means to deduce outflow velocities at coronal heights via direct Doppler shift measurements of coronal emission lines. Such direct Doppler shift measurements were not possible with previous spectrometers. We measure the outflow velocity at coronal heights in several on-disk long-duration plumes, which are located in coronal holes (CHs) and show significant blueshifts throughout the entire observational period. In one case, a plume is measured four hours apart. The deduced outflow velocitiesmore » are consistent, suggesting that the flows are quasi-steady. Furthermore, we provide an outflow velocity profile along the plumes, finding that the velocity corrected for the line-of-sight effect can reach 10 km s{sup –1} at 1.02 R {sub ☉}, 15 km s{sup –1} at 1.03 R {sub ☉}, and 25 km s{sup –1} at 1.05 R {sub ☉}. This clear signature of steady acceleration, combined with the fact that there is no significant blueshift at the base of plumes, provides an important constraint on plume models. At the height of 1.03 R {sub ☉}, EIS also deduced a density of 1.3 × 10{sup 8} cm{sup –3}, resulting in a proton flux of about 4.2 × 10{sup 9} cm{sup –2} s{sup –1} scaled to 1 AU, which is an order of magnitude higher than the proton input to a typical solar wind if a radial expansion is assumed. This suggests that CH plumes may be an important source of the solar wind.« less

New Images of the Solar Corona

NASA Astrophysics Data System (ADS)

Gurman, Joseph B.; Thompson, Barbara J.; Newmark, Jeffrey A.; Deforest, Craig E.

In 1.5 years of operation, The Extreme Ultraviolet Imaging Telescope (EIT) on SOHO has obtained over 40,000 images of the Sun in four wavebands between 171 Angstroms and 304 Angstroms, with spatial resolution limited only by the pixel scale of 2.59 arcsec. These images, and in particular compilations of time series of images into digital movies, have changed several of our ideas about the corona at temperatures of 0.9 - 2.5 MK. For the first time, we are able to see outflow in polar plumes and microjets inputting momentum into the high-speed, polar wind flow. For the first time, in conjunction with the LASCO coronagraphs and ground-based He I imagers, we have been able to see all the structures involved in coronal mass ejections (CMEs), from the surface of the Sun to 30 solar radii above it. In several cases, we have been able to observe directly the dramatic Moreton waves emanating from the active region where the CMEs originate, and radiating across virtually the entire visible hemisphere of the Sun. We interpret these large-scale coronal disturbances as fast-mode waves. Such events appear in the SOHO-LASCO coronagraphs as earthward-directed, and several have been detected by solar wind monitoring experiments on SOHO and other spacecraft. We have been able to view a variety of small-scale phenomena as well, including motions in prominences and filaments, macrospicular and polar microjet eruptions, and fine structures in the polar crown filament belt. The multi-wavelength capability of EIT makes it possible to determine the temperature of the coronal plasma and, here, too, we have been afforded a novel view: the heating in coronal active regions occurs over a considerably larger area than the high-density loops structures alone (i.e., bright features) would indicate.

GLOBAL ENERGETICS OF SOLAR FLARES. IV. CORONAL MASS EJECTION ENERGETICS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aschwanden, Markus J., E-mail: aschwanden@lmsal.com

2016-11-01

This study entails the fourth part of a global flare energetics project, in which the mass m {sub cme}, kinetic energy E {sub kin}, and the gravitational potential energy E {sub grav} of coronal mass ejections (CMEs) is measured in 399 M and X-class flare events observed during the first 3.5 years of the Solar Dynamics Observatory (SDO) mission, using a new method based on the EUV dimming effect. EUV dimming is modeled in terms of a radial adiabatic expansion process, which is fitted to the observed evolution of the total emission measure of the CME source region. The modelmore » derives the evolution of the mean electron density, the emission measure, the bulk plasma expansion velocity, the mass, and the energy in the CME source region. The EUV dimming method is truly complementary to the Thomson scattering method in white light, which probes the CME evolution in the heliosphere at r ≳ 2 R {sub ⊙}, while the EUV dimming method tracks the CME launch in the corona. We compare the CME parameters obtained in white light with the LASCO/C2 coronagraph with those obtained from EUV dimming with the Atmospheric Imaging Assembly onboard the SDO for all identical events in both data sets. We investigate correlations between CME parameters, the relative timing with flare parameters, frequency occurrence distributions, and the energy partition between magnetic, thermal, nonthermal, and CME energies. CME energies are found to be systematically lower than the dissipated magnetic energies, which is consistent with a magnetic origin of CMEs.« less

Coronal Bright Points Associated with Minifilament Eruptions

NASA Astrophysics Data System (ADS)

Hong, Junchao; Jiang, Yunchun; Yang, Jiayan; Bi, Yi; Li, Haidong; Yang, Bo; Yang, Dan

2014-12-01

Coronal bright points (CBPs) are small-scale, long-lived coronal brightenings that always correspond to photospheric network magnetic features of opposite polarity. In this paper, we subjectively adopt 30 CBPs in a coronal hole to study their eruptive behavior using data from the Atmospheric Imaging Assembly (AIA) and the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamics Observatory. About one-quarter to one-third of the CBPs in the coronal hole go through one or more minifilament eruption(s) (MFE(s)) throughout their lifetimes. The MFEs occur in temporal association with the brightness maxima of CBPs and possibly result from the convergence and cancellation of underlying magnetic dipoles. Two examples of CBPs with MFEs are analyzed in detail, where minifilaments appear as dark features of a cool channel that divide the CBPs along the neutral lines of the dipoles beneath. The MFEs show the typical rising movements of filaments and mass ejections with brightenings at CBPs, similar to large-scale filament eruptions. Via differential emission measure analysis, it is found that CBPs are heated dramatically by their MFEs and the ejected plasmas in the MFEs have average temperatures close to the pre-eruption BP plasmas and electron densities typically near 109 cm-3. These new observational results indicate that CBPs are more complex in dynamical evolution and magnetic structure than previously thought.

Standing Kink modes in three-dimensional coronal loops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pascoe, D. J.; De Moortel, I., E-mail: dpascoe@mcs.st-andrews.ac.uk

2014-04-01

So far, the straight flux tube model proposed by Edwin and Roberts is the most commonly used tool in practical coronal seismology, in particular, to infer values of the (coronal) magnetic field from observed, standing kink mode oscillations. In this paper, we compare the period predicted by this basic model with three-dimensional (3D) numerical simulations of standing kink mode oscillations, as the period is a crucial parameter in the seismological inversion to determine the magnetic field. We perform numerical simulations of standing kink modes in both straight and curved 3D coronal loops and consider excitation by internal and external drivers.more » The period of oscillation for the displacement of dense coronal loops is determined by the loop length and the kink speed, in agreement with the estimate based on analytical theory for straight flux tubes. For curved coronal loops embedded in a magnetic arcade and excited by an external driver, a secondary mode with a period determined by the loop length and external Alfvén speed is also present. When a low number of oscillations is considered, these two periods can result in a single, non-resolved (broad) peak in the power spectrum, particularly for low values of the density contrast for which the two periods will be relatively similar. In that case (and for this particular geometry), the presence of this additional mode would lead to ambiguous seismological estimates of the magnetic field strength.« less

Validation of Spherically Symmetric Inversion by Use of a Tomographically Reconstructed Three-Dimensional Electron Density of the Solar Corona

NASA Technical Reports Server (NTRS)

Wang, Tongjiang; Davila, Joseph M.

2014-01-01

Determining the coronal electron density by the inversion of white-light polarized brightness (pB) measurements by coronagraphs is a classic problem in solar physics. An inversion technique based on the spherically symmetric geometry (spherically symmetric inversion, SSI) was developed in the 1950s and has been widely applied to interpret various observations. However, to date there is no study of the uncertainty estimation of this method. We here present the detailed assessment of this method using a three-dimensional (3D) electron density in the corona from 1.5 to 4 solar radius as a model, which is reconstructed by a tomography method from STEREO/COR1 observations during the solar minimum in February 2008 (Carrington Rotation, CR 2066).We first show in theory and observation that the spherically symmetric polynomial approximation (SSPA) method and the Van de Hulst inversion technique are equivalent. Then we assess the SSPA method using synthesized pB images from the 3D density model, and find that the SSPA density values are close to the model inputs for the streamer core near the plane of the sky (POS) with differences generally smaller than about a factor of two; the former has the lower peak but extends more in both longitudinal and latitudinal directions than the latter. We estimate that the SSPA method may resolve the coronal density structure near the POS with angular resolution in longitude of about 50 deg. Our results confirm the suggestion that the SSI method is applicable to the solar minimum streamer (belt), as stated in some previous studies. In addition, we demonstrate that the SSPA method can be used to reconstruct the 3D coronal density, roughly in agreement with the reconstruction by tomography for a period of low solar activity (CR 2066). We suggest that the SSI method is complementary to the 3D tomographic technique in some cases, given that the development of the latter is still an ongoing research effort.

Measuring Solar Coronal Magnetism during the Total Solar Eclipse of 2017

NASA Astrophysics Data System (ADS)

Gibson, K. L.; Tomczyk, S.

2017-12-01

The total solar eclipse on August 21, 2017 provided a notable opportunity to measure the solar corona at specific emission wavelengths to gain information about coronal magnetic fields. Solar magnetic fields are intimately related to the generation of space weather and its effects on the earth, and the infrared imaging and polarization information collected on coronal emission lines here will enhance the scientific value of several other ongoing experiments, as well as benefit the astrophysics and upper atmosphere communities. Coronal measurements were collected during the 2 minute and 24 second totality period from Casper Mountain, WY. Computer-controlled telescopes automatically inserted four different narrow band pass filters to capture images in the visible range on a 4D PolCam, and in the infrared range on the FLIR 8501c camera. Each band pass filter selects a specific wavelength range that corresponds to a known coronal emission line possessing magnetic sensitivity. The 4D PolCam incorporated a novel grid of linear polarizers precisely aligned with the micron scale pixels. This allowed for direct measurement of the degree of linear polarization in a very small instrument with no external moving parts as is typically required. The FLIR offers short exposure times to freeze motion and output accurate thermal measurements. This allowed a new observation of the sun's corona using thermo infrared technology.

Origins of the Solar Wind

NASA Technical Reports Server (NTRS)

Warren, Harry; Gurman, Joseph (Technical Monitor)

2002-01-01

This paper presented the differential emission measure analysis of SUMER observations of a coroner streamer. We found that: The coroner streamer is isothermal at all heights. This suggests that the loops comprising the streamer must have very flat temperature profiles. The coroner streamer is "overdense" relative to the predictions of hydrostatic equilibrium at most heights. At the lowest heights the streamer is actually "underdense". The SUMER temperature measurements are not consistent with those derived from simultaneous SXT observations. SXT indicates systematically higher temperatures as well as a strong temperature gradient. These SUMER measurements yield somewhat lower temperatures and no gradient in the temperature with height. Previous work has suggested that there may be a hot component to the streamer that is preferentially observed with SXT. Our analysis shows that high temperature emission lines would be observed with SUMER if this were true and thus discounts this possibility. We suggested that scattered light in SXT might produce spurious temperature measurements. The temperature and density structure of this coroner streamer are very similar to "TRACE" active region loops (flat temperature profiles, overdense relative to uniform heating, and relatively cool temperatures).

Effect of the Coronal Wall Thickness of Dental Implants on the Screw Joint Stability in the Internal Implant-Abutment Connection.

PubMed

Lee, Ji-Hye; Huh, Yoon-Hyuk; Park, Chan-Jin; Cho, Lee-Ra

2016-01-01

To evaluate the effect of implant coronal wall thickness on load-bearing capacity and screw joint stability. Experimental implants were customized after investigation of the thinnest coronal wall thickness of commercially available implant systems with a regular platform diameter. Implants with four coronal wall thicknesses (0.2, 0.3, 0.4, and 0.5 mm) were fabricated. Three sets of tests were performed. The first set was a failure test to evaluate load-bearing capacity and elastic limit. The second and third sets were cyclic and static loading tests. After abutment screw tightening of each implant, vertical cyclic loading of 250 N or static loading from 250 to 800 N was applied. Coronal diameter expansion, axial displacement, and removal torque values of the implants were compared. Repeated measures analysis of variance (ANOVA) was used for statistical analysis (α = .05). Implants with 0.2-mm coronal wall thickness demonstrated significantly low load-bearing capacity and elastic limit (both P < .05). These implants also showed significantly large coronal diameter expansion and axial displacement after screw tightening (both P < .05). Greater vertical load and thinner coronal wall thickness significantly increased coronal diameter expansion of the implant, axial displacement of the abutment, and removal torque loss of the abutment screw (all P < .05). Implant coronal wall thickness of 0.2 mm produces significantly inferior load-bearing capacity and screw joint stability.

Interplanetary type II radio bursts and their association with CMEs and flares

NASA Astrophysics Data System (ADS)

Shanmugaraju, A.; Suresh, K.; Vasanth, V.; Selvarani, G.; Umapathy, S.

2018-06-01

We study the characteristics of the CMEs and their association with the end-frequency of interplanetary (IP)-type-II bursts by analyzing a set of 138 events (IP-type-II bursts-flares-CMEs) observed during the period 1997-2012. The present analysis consider only the type II bursts having starting frequency < 14 MHz to avoid the extension of coronal type IIs. The selected events are classified into three groups depending on the end-frequency of type IIs as follows, (A) Higher, (B) Intermediate and (C) Lower end-frequency. We compare characteristics of CMEs, flares and type II burst for the three selected groups of events and report some of the important differences. The observed height of CMEs is compared with the height of IP type IIs estimated using the electron density models. By applying a density multiplier (m) to this model, the density has been constrained both in the upper corona and in the interplanetary medium, respectively as m= 1 to 10 and m = 1 to 3. This study indicates that there is a correlation between the observed CME height and estimated type II height for groups B and C events whereas this correlation is absent in group A. In all the groups (A, B & C), the different heights of CMEs and type II reveal that the type IIs are not only observed at the nose but also at the flank of the CMEs.

ANALYSIS OF CORONAL RAIN OBSERVED BY IRIS , HINODE /SOT, AND SDO /AIA: TRANSVERSE OSCILLATIONS, KINEMATICS, AND THERMAL EVOLUTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kohutova, P.; Verwichte, E., E-mail: p.kohutova@warwick.ac.uk

Coronal rain composed of cool plasma condensations falling from coronal heights along magnetic field lines is a phenomenon occurring mainly in active region coronal loops. Recent high-resolution observations have shown that coronal rain is much more common than previously thought, suggesting its important role in the chromosphere-corona mass cycle. We present the analysis of MHD oscillations and kinematics of the coronal rain observed in chromospheric and transition region lines by the Interface Region Imaging Spectrograph (IRIS) , the Hinode Solar Optical Telescope (SOT), and the Solar Dynamics Observatory ( SDO) Atmospheric Imaging Assembly (AIA). Two different regimes of transverse oscillationsmore » traced by the rain are detected: small-scale persistent oscillations driven by a continuously operating process and localized large-scale oscillations excited by a transient mechanism. The plasma condensations are found to move with speeds ranging from few km s{sup −1} up to 180 km s{sup −1} and with accelerations largely below the free-fall rate, likely explained by pressure effects and the ponderomotive force resulting from the loop oscillations. The observed evolution of the emission in individual SDO /AIA bandpasses is found to exhibit clear signatures of a gradual cooling of the plasma at the loop top. We determine the temperature evolution of the coronal loop plasma using regularized inversion to recover the differential emission measure (DEM) and by forward modeling the emission intensities in the SDO /AIA bandpasses using a two-component synthetic DEM model. The inferred evolution of the temperature and density of the plasma near the apex is consistent with the limit cycle model and suggests the loop is going through a sequence of periodically repeating heating-condensation cycles.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Ruisheng; Chen, Yao; Du, Guohui

Jets are defined as impulsive, well-collimated upflows, occurring in different layers of the solar atmosphere with different scales. Their relationship with coronal mass ejections (CMEs), another type of solar impulsive events, remains elusive. Using high-quality imaging data from the Atmospheric Imaging Assembly/Solar Dynamics Observatory, we show a well-observed coronal jet event, in which the part of the jet with embedding coronal loops runs into a nearby coronal hole (CH) and gets bounced in the opposite direction. This is evidenced by the flat shape of the jet front during its interaction with the CH and the V-shaped feature in the time-slicemore » plot of the interaction region. About a half-hour later, a CME with an initially narrow and jet-like front is observed by the LASCO C2 coronagraph propagating along the direction of the post-collision jet. We also observe some 304 Å dark material flowing from the jet–CH interaction region toward the CME. We thus suggest that the jet and the CME are physically connected, with the jet–CH collision and the large-scale magnetic topology of the CH being important in defining the eventual propagating direction of this particular jet–CME eruption.« less

Anomalously low C6+/C5+ ratio in solar wind: ACE/SWICS observation

NASA Astrophysics Data System (ADS)

Zhao, L.; Landi, E.; Kocher, M.; Lepri, S. T.; Fisk, L. A.; Zurbuchen, T. H.

2016-03-01

The Carbon and Oxygen ionization states in the solar wind plasma freeze-in within 2 solar radii (Rs) from the solar surface, and then they do not change as they propagate with the solar wind into the heliosphere. Therefore, the O7+/O6+ and C6+/C5+ charge state ratios measured in situ maintain a record of the thermal properties (electron temperature and density) of the inner corona where the solar wind originates. Since these two ratios freeze-in at very similar height, they are expected to be correlated. However, an investigation of the correlation between these two ratios as measured by ACE/SWICS instrument from 1998 to 201l shows that there is a subset of "Outliers" departing from the expected correlation. We find about 49.4% of these Outliers is related to the Interplanetary Coronal Mass Ejections (ICMEs), while 49.6% of them is slow speed wind (Vp < 500 km/s) and about 1.0% of them is fast solar wind (Vp > 500 km/s). We compare the outlier-slow-speed wind with the normal slow wind (defined as Vp < 500 km/s and O7+/O6+ > 0.2) and find that the reason that causes the Outliers to depart from the correlation is their extremely depleted C6+/C5+ ratio which is decreased by 80% compared to the normal slow wind. We discuss the implication of the Outlier solar wind for the solar wind acceleration mechanism.

Coronal Emission from dG Halo Stars

NASA Technical Reports Server (NTRS)

Mushotzky, Richard (Technical Monitor); Harnden, F. R.

2005-01-01

The halo dG star HD 114762 was observed with the XMM-Newton satellite on 28-29 June 2004, during orbit 834, and the data were processed using the XMM-Newton Science Analysis System (SAS), version 6.0.0. Somewhat surprisingly, the target was NOT detected during this approx.30 ks exposure, which yielded instead a count rate upper limit of less than 0.0041 cts/s. We computed an X-ray flux upper limit by assuming a Raymond-Smith thermal spectrum of coronal temperature 1 million degrees K, typical of quiet old stars, a hydrogen column density of 2-10$^{19)$ cm$^{-2)$ and sub-solar abundances of 0.2. Our calculated X-ray luminosity upper limit in the 0.25-7.8 keV band is L$_x < 4.95 $\\time$10$^{26)$ erg/s, where we have assumed a stellar distance of 28 pc. This relatively low upper limit has implications for the capability of metal poor stars to host solar-like dynamos, as we will report in a forthcoming paper (now in preparation).

DETECTION OF SUPERSONIC DOWNFLOWS AND ASSOCIATED HEATING EVENTS IN THE TRANSITION REGION ABOVE SUNSPOTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kleint, L.; Martínez-Sykora, J.; Antolin, P.

Interface Region Imaging Spectrograph data allow us to study the solar transition region (TR) with an unprecedented spatial resolution of 0.''33. On 2013 August 30, we observed bursts of high Doppler shifts suggesting strong supersonic downflows of up to 200 km s{sup –1} and weaker, slightly slower upflows in the spectral lines Mg II h and k, C II 1336, Si IV 1394 Å, and 1403 Å, that are correlated with brightenings in the slitjaw images (SJIs). The bursty behavior lasts throughout the 2 hr observation, with average burst durations of about 20 s. The locations of these short-lived events appear to bemore » the umbral and penumbral footpoints of EUV loops. Fast apparent downflows are observed along these loops in the SJIs and in the Atmospheric Imaging Assembly, suggesting that the loops are thermally unstable. We interpret the observations as cool material falling from coronal heights, and especially coronal rain produced along the thermally unstable loops, which leads to an increase of intensity at the loop footpoints, probably indicating an increase of density and temperature in the TR. The rain speeds are on the higher end of previously reported speeds for this phenomenon, and possibly higher than the free-fall velocity along the loops. On other observing days, similar bright dots are sometimes aligned into ribbons, resembling small flare ribbons. These observations provide a first insight into small-scale heating events in sunspots in the TR.« less

HiRISE/NEOCE: an ESA M5 formation flying proposed mission combining high resolution and coronagraphy for ultimate observations of the chromosphere, corona and interface

NASA Astrophysics Data System (ADS)

Damé, Luc; Von Fay-Siebenburgen Erdélyi, Robert

2016-07-01

The global understanding of the solar environment through the magnetic field emergence and dissipation, and its influence on Earth, is at the centre of the four major thematics addressed by HiRISE/NEOCE (High Resolution Imaging and Spectroscopy Explorer/New Externally Occulted Coronagraph Experiment). They are interlinked and also complementary: the internal structure of the Sun determines the surface activity and dynamics that trigger magnetic field structuring which evolution, variation and dissipation will, in turn, explain the coronal heating onset and the major energy releases that feed the influence of the Sun on Earth. The 4 major themes of HiRISE/NEOCE are: - fine structure of the chromosphere-corona interface by 2D spectroscopy in FUV at very high resolution; - coronal heating roots in inner corona by ultimate externally-occulted coronagraphy; - resolved and global helioseismology thanks to continuity and stability of observing at L1 Lagrange point; - solar variability and space climate with a global comprehensive view of UV variability as well. Recent missions have shown the definite role of waves and of the magnetic field deep in the inner corona, at the chromosphere-corona interface, where dramatic changes occur. The dynamics of the chromosphere and corona is controlled by the emerging magnetic field, guided by the coronal magnetic field. Accordingly, the direct measurement of the chromospheric and coronal magnetic fields is of prime importance. This is implemented in HiRISE/NEOCE, to be proposed for ESA M5 ideally placed at the L1 Lagrangian point, providing FUV imaging and spectro-imaging, EUV and XUV imaging and spectroscopy, and ultimate coronagraphy by a remote external occulter (two satellites in formation flying 375 m apart minimizing scattered light) allowing to characterize temperature, densities and velocities up to the solar upper chromosphere, transition zone and inner corona with, in particular, 2D very high resolution multi-spectral imaging-spectroscopy and direct coronal magnetic field measurement: a unique set of tools to understand the structuration and onset of coronal heating. We give a detailed account of the major scientific objectives, and present the ESA M5 proposed mission profile and model payload (in particular of the SuperASPIICS package of visible, NIR and UV, Lyman-Alpha and OVI, coronagraphs).

Relative coronal abundances derived from X-ray observations 3: The effect of cascades on the relative intensity of Fe (XVII) line fluxes, and a revised iron abundance

NASA Technical Reports Server (NTRS)

Walker, A. B. C., Jr.; Rugge, H. R.; Weiss, K.

1974-01-01

Permitted lines in the optically thin coronal X-ray spectrum were analyzed to find the distribution of coronal material, as a function of temperature, without special assumptions concerning coronal conditions. The resonance lines of N, O, Ne, Na, Mg, Al, Si, S, and Ar which dominate the quiet coronal spectrum below 25A were observed. Coronal models were constructed and the relative abundances of these elements were determined. The intensity in the lines of the 2p-3d transitions near 15A was used in conjunction with these coronal models, with the assumption of coronal excitation, to determine the Fe XVII abundance. The relative intensities of the 2p-3d Fe XVII lines observed in the corona agreed with theoretical prediction. Using a more complete theoretical model, and higher resolution observations, a revised calculation of iron abundance relative to hydrogen of 0.000026 was made.

Magnetic structure of sites of braiding in Hi-C active region

NASA Astrophysics Data System (ADS)

Tiwari, Sanjiv Kumar; Alexander, Caroline; Winebarger, Amy R.; Moore, Ronald L.

2014-06-01

High-resolution Coronal Imager (Hi-C) observations of an active region (AR) corona, at a spatial resolution of 0.2 arcsec, have offered the first direct evidence of field lines braiding, which could deliver sufficient energy to heat the AR corona by current dissipation via magnetic reconnection, a proposal given by Parker three decades ago. The energy required to heat the corona must be transported from the photosphere along the field lines. The mechanism that drives the energy transport to the corona is not yet fully understood.To investigate simultaneous magnetic and intensity structure in and around the AR in detail, we use SDO/HMI+AIA data of + / - 2 hours around the 5 minute Hi-C flight. In the case of the QS, work done by convection/granulation on the inter-granular feet of the coronal field lines probably translates into the heat observed in the corona. In the case of the AR, as here, there could be flux emergence, cancellation/submergence, or shear flows generating large stress and tension in coronal field loops which is released as heat in the corona. However, to the best of our knowledge, there is no observational evidence available to these processes. We investigate the changes taking place in the photospheric feet of the magnetic field involved with brightenings in the Hi-C AR corona. Using HMI 45s magnetograms of four hours we find that, out of the two Hi-C sub-regions where the braiding of field lines were recently detected, flux emergence takes place in one region and flux cancellation in the other. The field in these sub-regions are highly sheared and have apparent high speed plasma flows at their feet. Therefore, shearing flows plausibly power much of the coronal and transition region heating in these areas of the AR. In addition, the presence of large flux emergence/cancellation strongly suggests that the work done by these processes on the pre-existing field also drives much of the observed heating.For this work, SKT and CEA were supported by an appointment to the NASA Postdoctoral Program at the NASA Marshall Space Flight Center, administered by Oak Ridge Associated Universities through a contract with NASA, and AW and RLM were supported by funding from the Living With a Star Targeted Research and Technology Program of the Heliophysics Division of NASA's Science Mission Directorate.

Sparkling extreme-ultraviolet bright dots observed with Hi-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Régnier, S.; Alexander, C. E.; Walsh, R. W.

Observing the Sun at high time and spatial scales is a step toward understanding the finest and fundamental scales of heating events in the solar corona. The high-resolution coronal (Hi-C) instrument has provided the highest spatial and temporal resolution images of the solar corona in the EUV wavelength range to date. Hi-C observed an active region on 2012 July 11 that exhibits several interesting features in the EUV line at 193 Å. One of them is the existence of short, small brightenings 'sparkling' at the edge of the active region; we call these EUV bright dots (EBDs). Individual EBDs havemore » a characteristic duration of 25 s with a characteristic length of 680 km. These brightenings are not fully resolved by the SDO/AIA instrument at the same wavelength; however, they can be identified with respect to the Hi-C location of the EBDs. In addition, EBDs are seen in other chromospheric/coronal channels of SDO/AIA, which suggests a temperature between 0.5 and 1.5 MK. Based on their frequency in the Hi-C time series, we define four different categories of EBDs: single peak, double peak, long duration, and bursty. Based on a potential field extrapolation from an SDO/HMI magnetogram, the EBDs appear at the footpoints of large-scale, trans-equatorial coronal loops. The Hi-C observations provide the first evidence of small-scale EUV heating events at the base of these coronal loops, which have a free magnetic energy of the order of 10{sup 26} erg.« less

A comparison of non-local electron transport models for laser-plasmas relevant to inertial confinement fusion

DOE PAGES

Sherlock, M.; Brodrick, J. P.; Ridgers, C. P.

2017-08-08

Here, we compare the reduced non-local electron transport model developed to Vlasov-Fokker-Planck simulations. Two new test cases are considered: the propagation of a heat wave through a high density region into a lower density gas, and a one-dimensional hohlraum ablation problem. We find that the reduced model reproduces the peak heat flux well in the ablation region but significantly over-predicts the coronal preheat. The suitability of the reduced model for computing non-local transport effects other than thermal conductivity is considered by comparing the computed distribution function to the Vlasov-Fokker-Planck distribution function. It is shown that even when the reduced modelmore » reproduces the correct heat flux, the distribution function is significantly different to the Vlasov-Fokker-Planck prediction. Two simple modifications are considered which improve agreement between models in the coronal region.« less

The May 1997 SOHO-Ulysses Quadrature

NASA Technical Reports Server (NTRS)

Suess, Steven T.; Poletto, G.; Romoli, M.; Neugebauer, M.; Goldstein, B. E.; Simnett, G.

2000-01-01

We present results from the May 1997 SOHO-Ulysses quadrature, near sunspot minimum. Ulysses was at 5.1 AU, 100 north of the solar equator, and off the east limb. It was, by chance, also at the very northern edge of the streamer belt. Nevertheless, SWOOPS detected only slow, relatively smooth wind and there was no direct evidence of fast wind from the northern polar coronal hole or of mixing with fast wind. LASCO images show that the streamer belt at 10 N was narrow and sharp at the beginning and end of the two week observation interval, but broadened in the middle. A corresponding change in density, but not flow speed, occurred at Ulysses. Coronal densities derived from UVCS show that physical parameters in the lower corona are closely related to those in the solar wind, both over quiet intervals and in transient events on the limb. One small transient observed by both LASCO and UVCS is analyzed in detail.

Direct measurement of time-dependent anesthetized in vivo human pulp temperature.

PubMed

Runnacles, Patrício; Arrais, Cesar Augusto Galvão; Pochapski, Marcia Thais; dos Santos, Fábio André; Coelho, Ulisses; Gomes, João Carlos; De Goes, Mário Fernando; Gomes, Osnara Maria Mongruel; Rueggeberg, Frederick Allen

2015-01-01

Human intrapupal tooth temperature is considered to be similar to that of the body (≈37 °C), although the actual temperature has never been measured. This study evaluated the in vivo, human, basal, coronal intrapulpal temperature of anesthetized upper first premolars. After approval of the local Ethics Committee was obtained (protocol no. 255,945), upper right and left first premolars requiring extraction for orthodontic reasons from 8 volunteers, ranging from 12 to 30 years old, received infiltrative and intraligamental anesthesia. The teeth (n=15) were isolated using rubber dam and a small, occlusal preparation was made using high-speed handpiece, under constant air-water spray, until a minute pulp exposure was attained. The sterile probe from a wireless, NIST-traceable, temperature acquisition system (Thermes WFI) was inserted directly into the coronal pulp. Once the probe was properly positioned and stable, real-time temperature data were continuously acquired for approximately 25 min. Data (°C) were subjected to 2-tailed, paired t-test (α=0.05), and the 95% confidence intervals for the initial and 25-min mean temperatures were also determined. The initial pulp temperature value (31.8±1.5 °C) was significantly lower than after 25-min (35.3±0.7 °C) (p<0.05). The 95% confidence interval for the initial temperature ranged from 31.0 to 32.6 °C and from 35.0 to 35.7 °C after 25 min. A slow, gradual temperature increase was observed after probe insertion until the pulp temperature reached a plateau, usually after 15 min. Consistent coronal, human, in vivo temperature values were observed and were slightly, but significantly below that of body core temperature. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Two Coronal Mass Ejections Events Close to the Total Solar Eclipse Aug. 11, 1999

NASA Astrophysics Data System (ADS)

Churyumov, K. I.; Ivanchuk, V. I.

We present some results of exploration of the solar corona on the basis of analysis of its images obtained in Romania by K.I.Churyumov and in Bulgaria by V.Mormyl' and S.Kharchuk Aug. 11 1999. Structure of the corona is characterized by the presence of numerous power and thin rays which have mainly radial orientation in regard to the Sun. The high-latitude rays of the north hemisphere (especially in the NE sector) are inclined in the direction of the N-pole. The interesting peculiarity of the solar corona Aug. 11 1999 is the existence of the sabre-like thin double ray on the NE-limb, which goes from the solar limb region at p ~ 50o. It is close to the peculiar center of ``repulsion'', which is observed for the fan of rays of the E-limb. We proposed that the similar rays and the observed center of ``repulsion'' were an indicator (postcursor) which shows that in this place of the corona the phenomena of the coronal mass ejections (CME) of the coronal plasma occurred. This views was confirmed by observations of the solar corona with the help of the Lasco C2 coronograph of SOHO Aug. 10/11 1999. In the region of the NW-quadrant and near the W-equator the enough sharp transequatorial arc by height ~ 0.7Rsolar with the center at ϕo = +10 deg is detected. It is nonfull arcs which intersects set of rays structures and near its foundation on the altitude /~ 0.3Rsolar there is a coronal condensation with characteristic sizes Δ l ~ 0.1Rsolar. We think that it is tied with development of a coronal mass ejection (CME) detected by the coronograph Lasco C2 of SOHO Aug. 11/12, 1999. On the best pictures it is seen that CME had the angle sizes ~ 90 deg and filled in nearly the all NW quadrant as a not uniform buble. On the basis of the published data we determined several

“Soft that molds the hard:” Geometric morphometry of lateral atlantoaxial joints focusing on the role of cartilage in changing the contour of bony articular surfaces

PubMed Central

Prasad, Prashant Kumar; Salunke, Pravin; Sahni, Daisy; Kalra, Parveen

2017-01-01

Purpose: The existing literature on lateral atlantoaxial joints is predominantly on bony facets and is unable to explain various C1-2 motions observed. Geometric morphometry of facets would help us in understanding the role of cartilages in C1-2 biomechanics/kinematics. Objective: Anthropometric measurements (bone and cartilage) of the atlantoaxial joint and to assess the role of cartilages in joint biomechanics. Materials and Methods: The authors studied 10 cadaveric atlantoaxial lateral joints with the articular cartilage in situ and after removing it, using three-dimensional laser scanner. The data were compared using geometric morphometry with emphasis on surface contours of articulating surfaces. Results: The bony inferior articular facet of atlas is concave in both sagittal and coronal plane. The bony superior articular facet of axis is convex in sagittal plane and is concave (laterally) and convex medially in the coronal plane. The bony articulating surfaces were nonconcordant. The articular cartilages of both C1 and C2 are biconvex in both planes and are thicker than the concavities of bony articulating surfaces. Conclusion: The biconvex structure of cartilage converts the surface morphology of C1-C2 bony facets from concave on concavo-convex to convex on convex. This reduces the contact point making the six degrees of freedom of motion possible and also makes the joint gyroscopic. PMID:29403249

Coronal heating by stochastic magnetic pumping

NASA Technical Reports Server (NTRS)

Sturrock, P. A.; Uchida, Y.

1980-01-01

Recent observational data cast serious doubt on the widely held view that the Sun's corona is heated by traveling waves (acoustic or magnetohydrodynamic). It is proposed that the energy responsible for heating the corona is derived from the free energy of the coronal magnetic field derived from motion of the 'feet' of magnetic field lines in the photosphere. Stochastic motion of the feet of magnetic field lines leads, on the average, to a linear increase of magnetic free energy with time. This rate of energy input is calculated for a simple model of a single thin flux tube. The model appears to agree well with observational data if the magnetic flux originates in small regions of high magnetic field strength. On combining this energy input with estimates of energy loss by radiation and of energy redistribution by thermal conduction, we obtain scaling laws for density and temperature in terms of length and coronal magnetic field strength.

Simultaneous Solar Maximum Mission and Very Large Array (VLA) observations of solar active regions

NASA Technical Reports Server (NTRS)

Lang, K. R.

1985-01-01

Simultaneous observations of solar active regions with the Solar Maximum Mission (SMM) Satellite and the Very Large Array (VLA) have been obtained and analyzed. Combined results enhance the scientific return for beyond that expeted from using either SMM or VLA alone. A total of two weeks of simultaneous SMM/VLA data were obtained. The multiple wavelength VLA observations were used to determine the temperature and magnetic structure at different heights within coronal loops. These data are compared with simultaneous SMM observations. Several papers on the subject are in progress. They include VLA observations of compact, transient sources in the transition region; simultaneous SMM/VLA observations of the coronal loops in one active region and the evolution of another one; and sampling of the coronal plasma using thermal cyclotron lines (magnetic field - VLA) and soft X ray spectral lines (electron density and electron temperaure-SMM).

[Surface stress analysis of distal extension removable partial denture retained with two types of semi-precision attachments].

PubMed

Wang, Y; Mi, N; Qing, F; Liu, F; Chen, J

2001-10-01

The aims of this study are to analyze the surface stress of the periodontal supporting bone of the bilateral distol extension removable partial denture which is retained by using intra-coronal or extra-coronal semi-precision attachment, and to characterize the biomechanics of these two designs by using a strain gauge. A fresh human mandible specimen with 76|67 missing and six bilateral partial removable denture retained with six semi-precision attachments were made, including three attachments with intra-coronal studs and three attachments with extra-coronal vertical bars. A total of six 45 degrees rosette strain gauges were bonded at six prepared points on the surface of the mandible to measure the surface stress, including the middle point between 76 of the buccal edentulous alveolar crest area under the denture base verge(point 1), the distal buccal cervix of 5 (point 2), the buccal apical area of 5 (point 3), the buccal middle area of 34 roots (point 4, 5), the lingual middle area of 5 root (point 6). The static loads of 14N, 28N and 42N were applied vertically, buccally 45 degrees, lingually 45 degrees at the middle point of the 6|6 occlusal surface. The micro-strain was recorded, and the maximal/minimal principle stresses were calculated for each RPD and each point. The stress characteristics of these two types of attachments were compared and analyzed. In most situations, the stress of these two semi-precision attachments showed significant differences. The vertical load: The stress values of these intra-coronal and extra-coronal attachments at points 1, 2, 3, 4, 6 differed significantly(P < 0.05), including points 1, 2, (sigma intra < sigma extra) and points 3, 4, 6(sigma intra > sigma extra). Buccal loads: The stress values of these intra-coronal and extra-coronal attachments at points 1, 2, 3, 4, 5 differed significantly(P < 0.05), including points 1, 2(sigma intra < sigma extra) and points 3, 4, 5(sigma intra > sigma extra). Lingual loads: The stress values of these intra-coronal and extra-coronal attachments at points 2, 3, 4, 6 differed significantly (P < 0.05, sigma intra > sigma extra). The intra-coronal attachment generally produced higher stress at the site of the alveolar bone around the abutment than the extra-coronal attachment, but extra-coronal attachment produced higher stress at the edentulous alveolar crest and the distal cervical alveolar bone of the distal abutment than the intra-coronal attachment. The intra-coronal attachment is suggested to be applied in some cases that the periodontal condition of distal abutment was good, and the extra-coronal attachment is suggested to be used in some cases that the condition of the edentulous alveolar crest is fairly good, while the periodontal condition of the distal abutment was relatively weak.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, D.; Van Driel-Gesztelyi, L.; Green, L. M.

Using spectra obtained by the EUV Imaging Spectrometer (EIS) instrument onboard Hinode, we present a detailed spatially resolved abundance map of an active region (AR)-coronal hole (CH) complex that covers an area of 359'' × 485''. The abundance map provides first ionization potential (FIP) bias levels in various coronal structures within the large EIS field of view. Overall, FIP bias in the small, relatively young AR is 2-3. This modest FIP bias is a consequence of the age of the AR, its weak heating, and its partial reconnection with the surrounding CH. Plasma with a coronal composition is concentrated atmore » AR loop footpoints, close to where fractionation is believed to take place in the chromosphere. In the AR, we found a moderate positive correlation of FIP bias with nonthermal velocity and magnetic flux density, both of which are also strongest at the AR loop footpoints. Pathways of slightly enhanced FIP bias are traced along some of the loops connecting opposite polarities within the AR. We interpret the traces of enhanced FIP bias along these loops to be the beginning of fractionated plasma mixing in the loops. Low FIP bias in a sigmoidal channel above the AR's main polarity inversion line, where ongoing flux cancellation is taking place, provides new evidence of a bald patch magnetic topology of a sigmoid/flux rope configuration.« less

The Width Distribution of Loops and Strands in the Solar Corona—Are We Hitting Rock Bottom?

NASA Astrophysics Data System (ADS)

Aschwanden, Markus J.; Peter, Hardi

2017-05-01

In this study, we analyze Atmospheric Imaging Assembly (AIA) and Hi-C images in order to investigate absolute limits for the finest loop strands. We develop a model of the occurrence-size distribution function of coronal loop widths, characterized by the lower limit of widths w min, the peak (or most frequent) width w p , the peak occurrence number n p , and a power-law slope a. Our data analysis includes automated tracing of curvilinear features with the OCCULT-2 code, automated sampling of the cross-sectional widths of coronal loops, and fitting of the theoretical size distribution to the observed distribution. With Monte Carlo simulations and variable pixel sizes {{Δ }}x, we derive a first diagnostic criterion to discriminate whether the loop widths are unresolved ({w}p/{{Δ }}x≈ 2.5+/- 0.2) or fully resolved (if {w}p/{{Δ }}x≳ 2.7). For images with resolved loop widths, we can apply a second diagnostic criterion that predicts the lower limit of loop widths as a function of the spatial resolution. We find that the loop widths are marginally resolved in AIA images but are fully resolved in Hi-C images, where our model predicts a most frequent (peak) value at {w}p≈ 550 {km}, in agreement with recent results of Brooks et al. This result agrees with the statistics of photospheric granulation sizes and thus supports coronal heating mechanisms operating on the macroscopic scale of photospheric magneto-convection, rather than nanoflare braiding models on unresolved microscopic scales.

REFLECTION OF PROPAGATING SLOW MAGNETO-ACOUSTIC WAVES IN HOT CORONAL LOOPS: MULTI-INSTRUMENT OBSERVATIONS AND NUMERICAL MODELING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandal, Sudip; Banerjee, Dipankar; Pant, Vaibhav

Slow MHD waves are important tools for understanding coronal structures and dynamics. In this paper, we report a number of observations from the X-Ray Telescope (XRT) on board HINODE and Solar Dynamic Observatory /Atmospheric Imaging Assembly (AIA) of reflecting longitudinal waves in hot coronal loops. To our knowledge, this is the first report of this kind as seen from the XRT and simultaneously with the AIA. The wave appears after a micro-flare occurs at one of the footpoints. We estimate the density and temperature of the loop plasma by performing differential emission measure (DEM) analysis on the AIA image sequence.more » The estimated speed of propagation is comparable to or lower than the local sound speed, suggesting it to be a propagating slow wave. The intensity perturbation amplitude, in every case, falls very rapidly as the perturbation moves along the loop and eventually vanishes after one or more reflections. To check the consistency of such reflection signatures with the obtained loop parameters, we perform a 2.5D MHD simulation, which uses the parameters obtained from our observation as inputs, and perform forward modeling to synthesize AIA 94 Å images. Analyzing the synthesized images, we obtain the same properties of the observables as for the real observation. From the analysis we conclude that a footpoint heating can generate a slow wave which then reflects back and forth in the coronal loop before fading. Our analysis of the simulated data shows that the main agent for this damping is anisotropic thermal conduction.« less

Three-Dimensional Morphology of a Coronal Prominence Cavity

NASA Technical Reports Server (NTRS)

Gibson, S. E.; Kucera, T. A.; Rastawicki, D.; Dove, J.; deToma, G.; Hao, J.; Hill, S.; Hudson, H. S.; Marque, C.; McIntosh, P. S.;

COMPARING SPATIAL DISTRIBUTIONS OF SOLAR PROMINENCE MASS DERIVED FROM CORONAL ABSORPTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Holly; Kilper, Gary; Kucera, Therese

2011-01-20

In a previous study, Gilbert et al. derived the column density and total mass of solar prominences using a new technique, which measures how much coronal radiation in the Fe XII (195 A) spectral band is absorbed by prominence material, while considering the effects of both foreground and background radiation. In the present work, we apply this method to a sample of prominence observations in three different wavelength regimes: one in which only H{sup 0} is ionized (504 A < {lambda} < 911 A), a second where both H{sup 0} and He{sup 0} are ionized (228 A < {lambda}

Real-time forecasting of ICME shock arrivals at L1 during the "April Fool’s Day" epoch: 28 March  21 April 2001

NASA Astrophysics Data System (ADS)

Sun, W.; Dryer, M.; Fry, C. D.; Deehr, C. S.; Smith, Z.; Akasofu, S.-I.; Kartalev, M. D.; Grigorov, K. G.

2002-07-01

The Sun was extremely active during the "April Fool’s Day" epoch of 2001. We chose this period between a solar flare on 28 March 2001 to a final shock arrival at Earth on 21 April 2001. The activity consisted of two presumed helmet-streamer blowouts, seven M-class flares, and nine X-class flares, the last of which was behind the west limb. We have been experimenting since February 1997 with real-time, end-to-end forecasting of interplanetary coronal mass ejection (ICME) shock arrival times. Since August 1998, these forecasts have been distributed in real-time by e-mail to a list of interested scientists and operational USAF and NOAA forecasters. They are made using three different solar wind models. We describe here the solar events observed during the April Fool’s 2001 epoch, along with the predicted and actual shock arrival times, and the ex post facto correction to the real-time coronal shock speed observations. It appears that the initial estimates of coronal shock speeds from Type II radio burst observations and coronal mass ejections were too high by as much as 30%. We conclude that a 3-dimensional coronal density model should be developed for application to observations of solar flares and their Type II radio burst observations.

Using observations of slipping velocities to test the hypothesis that reconnection heats the active region corona

NASA Astrophysics Data System (ADS)

Yang, Kai; Longcope, Dana; Guo, Yang; Ding, Mingde

2017-08-01

Numerous proposed coronal heating mechanisms have invoked magnetic reconnection in some role. Testing such a mechanism requires a method of measuring magnetic reconnection coupled with a prediction of the heat delivered by reconnection at the observed rate. In the absence of coronal reconnection, field line footpoints move at the same velocity as the plasma they find themselves in. The rate of coronal reconnection is therefore related to any discrepancy observed between footpoint motion and that of the local plasma — so-called slipping motion. We propose a novel method to measure this velocity discrepancy by combining a sequence of non-linear force-free field extrapolations with maps of photospheric velocity. We obtain both from a sequence of vector magnetograms of an active region (AR). We then propose a method of computing the coronal heating produced under the assumption the observed slipping velocity was due entirely to coronal reconnection. This heating rate is used to predict density and temperature at points along an equilibrium loop. This, in turn, is used to synthesize emission in EUV and SXR bands. We perform this analysis using a sequence of HMI vector magnetograms of a particular AR and compare synthesized images to observations of the same AR made by SDO. We also compare differential emission measure inferred from those observations to that of the modeled corona.

Coronal bright points associated with minifilament eruptions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Junchao; Jiang, Yunchun; Yang, Jiayan

2014-12-01

Coronal bright points (CBPs) are small-scale, long-lived coronal brightenings that always correspond to photospheric network magnetic features of opposite polarity. In this paper, we subjectively adopt 30 CBPs in a coronal hole to study their eruptive behavior using data from the Atmospheric Imaging Assembly (AIA) and the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamics Observatory. About one-quarter to one-third of the CBPs in the coronal hole go through one or more minifilament eruption(s) (MFE(s)) throughout their lifetimes. The MFEs occur in temporal association with the brightness maxima of CBPs and possibly result from the convergence and cancellationmore » of underlying magnetic dipoles. Two examples of CBPs with MFEs are analyzed in detail, where minifilaments appear as dark features of a cool channel that divide the CBPs along the neutral lines of the dipoles beneath. The MFEs show the typical rising movements of filaments and mass ejections with brightenings at CBPs, similar to large-scale filament eruptions. Via differential emission measure analysis, it is found that CBPs are heated dramatically by their MFEs and the ejected plasmas in the MFEs have average temperatures close to the pre-eruption BP plasmas and electron densities typically near 10{sup 9} cm{sup –3}. These new observational results indicate that CBPs are more complex in dynamical evolution and magnetic structure than previously thought.« less

Renewal: New Aspects of Acceleration and Transport of Solar Energetic Particles (SEPs) from the Sun to the Earth

DTIC Science & Technology

2014-10-31

Hole .......................................................4 2. SOHO EIT Image with Coronal Holes and FPA Vector...Diagram of CME Deflection by a Coronal Hole Figure 2: SOHO EIT Image with Coronal Holes and FPA Vector Approved for public release; distribution

Effect of Various Laser Wavelengths on Temperature Changes During Periimplantitis Treatment: An in vitro Study.

PubMed

Monzavi, Abbas; Fekrazad, Reza; Chinipardaz, Zahra; Shahabi, Sima; Behruzi, Roohollah; Chiniforush, Nasim

2018-06-01

This study aimed to investigate and compare temperature change during implant decontamination with different laser types (carbon dioxide [Co2]/diode/neodymium-doped yttrium aluminum garnet [Nd:YAG]/erbium-doped yttrium aluminum garnet [Er:YAG]/antimicrobial photodynamic therapy [aPDT]). Sixty implants were inserted into a bone block cut from a sheep's mandible. A 3 × 8 mm vertical lesion was made at the buccal of each implant. The bone block was placed into a 37°C water bath to simulate the in vivo oral condition. A K-type thermocouple was placed in contact with the implant to register temperature changes at 3 points (apical/middle/coronal). In the entire laser irradiations, the mean of temperature changes remains below 10°C. The apical temperature rise was higher than the coronal and middle regions (P < 0.05), and the apical temperature took longer time to reach the initial temperature (37°C) (P < 0.001). Temperature changes over 10°C occurred at the apical point of the implants with the Co2, Nd:YAG, and diode laser irradiations; however, only the Co2 laser reached the statistical significance in this regard (P < 0.05). Our findings indicate the promising results of Er:YAG laser and aPDT in implant decontamination. Precaution should be taken in the application of Nd:YAG, diode, and especially Co2 lasers.

Application of a high-density gas laser target to the physics of x-ray lasers and coronal plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pronko, J.G.; Kohler, D.

1996-05-31

An experiment has been proposed to investigate a photopumped x-ray laser approach using a novel, high-density, laser heated supersonic gas jet plasma to prepare the lasant plasma. The scheme uses the He- like sodium 1.10027 nm line to pump the He-like neon 1s-4p transition at 1.10003 nm with the lasing transitions between the n=4 to n=2,3 states and the n=3 to n=2 state at 5.8 nm, 23.0 nm, and 8.2 nm, respectively. The experiment had been proposed in 1990 and funding began Jan. 1991; however circumstances made it impossible to pursue the research over the past 5 years, and itmore » was decided not to pursue the research any further.« less

Hot interstellar gas and ionization of embedded clouds

NASA Technical Reports Server (NTRS)

Cheng, K.-P.; Bruhweiler, F.

1990-01-01

Researchers present detailed photoionization calculations for the instellar cloud in which the Sun is embedded. They consider the EUV radiation field with contribution from discrete stellar sources and from a thermal bremsstrahlung-radiative recombination spectrum emitted from the surrounding 10 to the 6th power k coronal substrate. They establish lower limits to the fractional ionization of hydrogen and helium of 0.17 and 0.29 respectively. The high He ionization fraction results primarily from very strong line emission below 500 A originating in the surrounding coronal substrate while the H ionization is dominated by the EUV radiation from the discrete stellar sources. The dual effects of thermal conduction and the EUV spectrum of the 10 to the 6th k plasma on ionization in the cloud skin are explored. The EUV radiation field and Auger ionization have insignificant effects on the resulting ionic column densities of Si IV, C IV, N V and O VI through the cloud skin. Calculations show that the abundances of these species are dominated by collisional ionization in the thermal conduction front. Because of a low charge exchange rate with hydrogen, the ionic column density ratios of N (CIII)/N (CII) and N (NII)/N (NI) are dominated by the EUV radiation field in the local interstellar medium. These ratios should be important diagnostics for the EUV radiation field and serve as surrogate indicators of the interstellar He and H ionization fraction respectively. Spacecraft such as Lyman which is designed to obtain high resolution spectral data down to the Lyman limit at 912 A could sample interstellar lines of these ions.

Invisibility of Solar Active Region Umbra-to-Umbra Coronal Loops: New Evidence that Magnetoconvection Drives Solar-Stellar Coronal Heating

NASA Technical Reports Server (NTRS)

Tiwari, Sanjiv K.; Thalmann, Julia K.; Panesar, Navdeep K.; Moore, Ronald L.; Winebarger, Amy R.

2017-01-01

Coronal heating generally increases with increasing magnetic field strength: the EUV/X-ray corona in active regions is 10--100 times more luminous and 2--4 times hotter than that in quiet regions and coronal holes, which are heated to only about 1.5 MK, and have fields that are 10--100 times weaker than that in active regions. From a comparison of a nonlinear force-free model of the three-dimensional active region coronal field to observed extreme-ultraviolet loops, we find that (1) umbra-to-umbra coronal loops, despite being rooted in the strongest magnetic flux, are invisible, and (2) the brightest loops have one foot in an umbra or penumbra and the other foot in another sunspot's penumbra or in unipolar or mixed-polarity plage. The invisibility of umbra-to-umbra loops is new evidence that magnetoconvection drives solar-stellar coronal heating: evidently, the strong umbral field at both ends quenches the magnetoconvection and hence the heating. Our results from EUV observations and nonlinear force-free modeling of coronal magnetic field imply that, for any coronal loop on the Sun or on any other convective star, as long as the field can be braided by convection in at least one loop foot, the stronger the field in the loop, the stronger the coronal heating.

Higher-speed coronal mass ejections and their geoeffectiveness

NASA Astrophysics Data System (ADS)

Singh, A. K.; Bhargawa, Asheesh; Tonk, Apeksha

2018-06-01

We have attempted to examine the ability of coronal mass ejections to cause geoeffectiveness. To that end, we have investigated total 571 cases of higher-speed (> 1000 km/s) coronal mass ejection events observed during the years 1996-2012. On the basis of angular width (W) of observance, events of coronal mass ejection were further classified as front-side or halo coronal mass ejections (W = 360°); back-side halo coronal mass ejections (W = 360°); partial halo (120°< W < 360°) and non-halo (W < 120°). From further analysis, we found that front halo coronal mass ejections were much faster and more geoeffective in comparison of partial halo and non-halo coronal mass ejections. We also inferred that the front-sided halo coronal mass ejections were 67.1% geoeffective while geoeffectiveness of partial halo coronal mass ejections and non-halo coronal mass ejections were found to be 44.2% and 56.6% respectively. During the same period of observation, 43% of back-sided CMEs showed geoeffectiveness. We have also investigated some events of coronal mass ejections having speed > 2500 km/s as a case study. We have concluded that mere speed of coronal mass ejection and their association with solar flares or solar activity were not mere criterion for producing geoeffectiveness but angular width of coronal mass ejections and their originating position also played a key role.

Imaging Coronal Mass Ejections and Large-Scale Solar Wind Structure Using IPS and Thomson-Scattered Sunlight (Invited)

NASA Astrophysics Data System (ADS)

Clover, J. M.; Jackson, B. V.; Buffington, A.; Hick, P. P.; Bisi, M. M.; Tokumaru, M.; Fujiki, K.

2010-12-01

The Solar Mass Ejection Imager (SMEI) observes Thomson-scattered white light from heliospheric electrons across almost all of the sky nearly all of the time since early 2003. Interplanetary scintillation (IPS) observations of velocity and g-level provide similar structure information but with a less-complete sky-and-time coverage. The Solar TErrestrial RElations Observatory (STEREO) twin spacecraft outer Heliospheric Imagers (HI-2) currently image the heliosphere in Thomson-scattered light near the ecliptic plane far from Earth. The Solar-Terrestrial Environment Laboratory (STELab) IPS observations provide IPS velocity and g-level values, which in conjunction with our tomographic reconstruction program, yield velocities and densities of the inner heliosphere in three dimensions. The same tomographic program substitutes SMEI Thomson-scattering brightness information for the g-level values to derive heliospheric densities from these data alone. We look at the global structure of the heliosphere concentrating mainly on three events from 2007 through the rise phase of Solar Cycle 24. The first event, observed in both the IPS and SMEI defines the three-dimensional velocity and density structure around the time of the shock observed at Earth on 02:02 UT 17 December 2007. The second event, seen only by SMEI, is that of the 23-26 April 2008 coronal mass ejection (CME) and its interplanetary counterpart. The third event is the CME (and its interplanetary counterpart) that took place 17 January 2010 and arrived at STEREO-B about four days later. For each event, we isolate the particular portion of the heliosphere attributed to the transient density structure using our tomographic technique, and then estimate its extent.

Fine Structures of Solar Radio Type III Bursts and Their Possible Relationship with Coronal Density Turbulence

NASA Astrophysics Data System (ADS)

Chen, Xingyao; Kontar, Eduard P.; Yu, Sijie; Yan, Yihua; Huang, Jing; Tan, Baolin

2018-03-01

Solar radio type III bursts are believed to be the most sensitive signatures of near-relativistic electron beam propagation in the corona. A solar radio type IIIb-III pair burst with fine frequency structures, observed by the Low Frequency Array (LOFAR) with high temporal (∼10 ms) and spectral (12.5 kHz) resolutions at 30–80 MHz, is presented. The observations show that the type III burst consists of many striae, which have a frequency scale of about 0.1 MHz in both the fundamental (plasma) and the harmonic (double plasma) emission. We investigate the effects of background density fluctuations based on the observation of striae structure to estimate the density perturbation in the solar corona. It is found that the spectral index of the density fluctuation spectrum is about ‑1.7, and the characteristic spatial scale of the density perturbation is around 700 km. This spectral index is very close to a Kolmogorov turbulence spectral index of ‑5/3, consistent with a turbulent cascade. This fact indicates that the coronal turbulence may play the important role of modulating the time structures of solar radio type III bursts, and the fine structure of radio type III bursts could provide a useful and unique tool to diagnose the turbulence in the solar corona.

THE BLOB CONNECTION: SEARCHING FOR LOW CORONAL SIGNATURES OF SOLAR POST-CME BLOBS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schanche, Nicole E; Reeves, Katharine K; Webb, David F., E-mail: nschanche@cfa.harvard.edu

2016-11-01

Bright linear structures, thought to be indicators of a current sheet (CS), are often seen in Large Angle and Spectrometric Coronagraph (LASCO) on the Solar and Heliospheric Observatory (SOHO) white-light data in the wake of coronal mass ejections (CMEs). In a subset of these post-CME structures, relatively bright blobs are seen moving outward along the rays. These blobs have been interpreted as consequences of the plasmoid instability in the CS, and can help us to understand the dynamics of the reconnection. We examine several instances, taken largely from the SOHO /LASCO CME-rays Catalog, where these blobs are clearly visible inmore » white-light data. Using radially filtered, difference, wavelet enhanced, and multiscale Gaussian normalized images to visually inspect Solar Dynamics Observatory /Atmospheric Imaging Assembly (AIA) data in multiple wavelengths, we look for signatures of material that correspond both temporally and spatially to the later appearance of the blobs in LASCO/C2. Constraints from measurements of the blobs allow us to predict the expected count rates in DN pixel{sup −1} s{sup −1} for each AIA channel. The resulting values would make the blobs bright enough to be detectable at 1.2 R {sub ⊙}. However, we do not see conclusive evidence for corresponding blobs in the AIA data in any of the events. We do the same calculation for the “cartwheel CME,” an event in which blobs were seen in X-rays, and find that our estimated count rates are close to those observed. We suggest several possibilities for the absence of the EUV blobs including the formation of the blob higher than the AIA field of view, blob coalescence, and overestimation of blob densities.« less

Coronal holes as sources of solar wind

NASA Technical Reports Server (NTRS)

Nolte, J. T.; Krieger, A. S.; Timothy, A. F.; Gold, R. E.; Roelof, E. C.; Vaiana, G.; Lazarus, A. J.; Sullivan, J. D.; Mcintosh, P. S.

1976-01-01

We investigate the association of high-speed solar wind with coronal holes during the Skylab mission by: (1) direct comparison of solar wind and coronal X-ray data; (2) comparison of near-equatorial coronal hole area with maximum solar wind velocity in the associated streams; and (3) examination of the correlation between solar and interplanetary magnetic polarities. We find that all large near-equatorial coronal holes seen during the Skylab period were associated with high-velocity solar wind streams observed at 1 AU.

Comparison between field mill and corona point instrumentation at Kennedy Space Center - Use of these data with a model to determine cloudbase electric fields

NASA Technical Reports Server (NTRS)

Markson, R.; Anderson, B.; Govaert, J.; Fairall, C. W.

1989-01-01

A novel coronal current-determining instrument is being used at NASA-KSC which overcomes previous difficulties with wind sensitivity and a voltage-threshold 'deadband'. The mounting of the corona needle at an elevated location reduces coronal and electrode layer space-charge influences on electric fields, rendering the measurement of space charge density possible. In conjunction with a space-charge compensation model, these features allow a more realistic estimation of cloud base electric fields and the potential for lightning strike than has previously been possible with ground-based sensors.

A Normal Incidence X-ray Telescope (NIXT) Sounding Rocket Payload

NASA Technical Reports Server (NTRS)

Golub, Leon

1998-01-01

The solar corona, and the coronae of solar-type stars, consist of a low-density magnetized plasma at temperatures exceeding 10(exp 6) K. The primary coronal emission is therefore in the UV and soft X-ray range. The observed close connection between solar magnetic fields and the physical parameters of the corona implies a fundamental role for the magnetic field in coronal structuring and dynamics. Variability of the corona occurs on all temporal and spatial scales - at one extreme, as the result of plasma instabilities, and at the other extreme driven by the global magnetic flux emergence patterns of the solar cycle.

EUV lines observed with EIS/Hinode in a solar prominence

NASA Astrophysics Data System (ADS)

Labrosse, N.; Schmieder, B.; Heinzel, P.; Watanabe, T.

2011-07-01

Context. During a multi-wavelength observation campaign with Hinode and ground-based instruments, a solar prominence was observed for three consecutive days as it crossed the western limb of the Sun in April 2007. Aims: We report on observations obtained on 26 April 2007 using EIS (Extreme ultraviolet Imaging Spectrometer) on Hinode. They are analysed to provide a qualitative diagnostic of the plasma in different parts of the prominence. Methods: After correcting for instrumental effects, the rasters at different wavelengths are presented. Several regions within the same prominence are identified for further analysis. Selected profiles for lines with formation temperatures between log (T) = 4.7 and log (T) = 6.3, as well as their integrated intensities, are given. The profiles of coronal, transition region, and He ii lines are discussed. We pay special attention to the He ii line, which is blended with coronal lines. Results: Some quantitative results are obtained by analysing the line profiles. They confirm that depression in EUV lines can be interpreted in terms of two mechanisms: absorption of coronal radiation by the hydrogen and neutral helium resonance continua, and emissivity blocking. We present estimates of the He ii line integrated intensity in different parts of the prominence according to different scenarios for the relative contribution of absorption and emissivity blocking to the coronal lines blended with the He ii line. We estimate the contribution of the He ii 256.32 Å line to the He ii raster image to vary between ~44% and 70% of the raster's total intensity in the prominence according to the different models used to take into account the blending coronal lines. The inferred integrated intensities of the He ii 256 Å line are consistent with the theoretical intensities obtained with previous 1D non-LTE radiative transfer calculations, yielding a preliminary estimate of the central temperature of 8700 K, a central pressure of 0.33 dyn cm-2, and a column mass of 2.5 × 10-4 g cm-2. The corresponding theoretical hydrogen column density (1020 cm-2) is about two orders of magnitude higher than those inferred from the opacity estimates at 195 Å. The non-LTE calculations indicate that the He ii 256.32 Å line is essentially formed in the prominence-to-corona transition region by resonant scattering of the incident radiation. The movie associated to Fig. 2 is available in electronic form at http://www.aanda.org

Towards a Data-Optimized Coronal Magnetic Field Model (DOC-FM): Synthetic Test Beds and Multiwavelength Forward Modeling

NASA Astrophysics Data System (ADS)

Gibson, S. E.; Dalmasse, K.; Fan, Y.; Fineschi, S.; MacKay, D.; Rempel, M.; White, S. M.

2015-12-01

Understanding the physical state of the solar corona is key to deciphering the origins of space weather as well as to realistically representing the environment to be navigated by missions such as Solar Orbiter and Solar Probe Plus. However, inverting solar coronal observations to reconstruct this physical state -- and in particular the three-dimensional coronal magnetic field - is complicated by limited lines of sight and by projection effects. On the other hand, the sensitivity of multiwavelength observations to different physical mechanisms implies a potential for simultaneous probing of different parts of the coronal plasma. In order to study this complementarity, and to ultimately establish an optimal set of observations for constraining the three-dimensional coronal magnetic field, we are developing a suite of representative simulations to act as diagnostic test beds. We will present three such test beds: a coronal active region, a quiescent prominence, and a global corona. Each fully define the physical state of density, temperature, and vector magnetic field in three dimensions throughout the simulation domain. From these test beds, and using the FORWARD SolarSoft IDL codes, we will create a broad range of synthetic data. Radio observables will include intensity and circular polarization (including gyroresonance effects) and Faraday rotation for a range of frequencies. Infrared and visible forbidden line diagnostics of Zeeman and saturated Hanle effects will yield full Stokes vector (I, Q, U, V) synthetic data, and UV permitted line Hanle diagnostics will yield intensity and linear polarization. In addition, we will synthesize UV and SXR imager data, UV/EUV spectrometric data, and white light brightness and polarized brightness. All of these synthetic data, along with the "ground truth" physical state of the simulations from which they are derived, will be made available to the community for the purpose of testing coronal inversion techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takahashi, Takuya, E-mail: takahashi@kwasan.kyoto-u.ac.jp

Flare-associated coronal shock waves sometimes interact with solar prominences, leading to large-amplitude prominence oscillations (LAPOs). Such prominence activation gives us a unique opportunity to track the time evolution of shock–cloud interaction in cosmic plasmas. Although the dynamics of interstellar shock–cloud interaction has been extensively studied, coronal shock–solar prominence interaction is rarely studied in the context of shock–cloud interaction. Associated with the X5.4 class solar flare that occurred on 2012 March 7, a globally propagated coronal shock wave interacted with a polar prominence, leading to LAPO. In this paper, we studied bulk acceleration and excitation of the internal flow of themore » shocked prominence using three-dimensional magnetohydrodynamic (MHD) simulations. We studied eight MHD simulation runs, each with different mass density structure of the prominence, and one hydrodynamic simulation run, and we compared the result. In order to compare the observed motion of activated prominence with the corresponding simulation, we also studied prominence activation by injection of a triangular-shaped coronal shock. We found that the prominence is first accelerated mainly by magnetic tension force as well as direct transmission of the shock, and later decelerated mainly by magnetic tension force. The internal flow, on the other hand, is excited during the shock front sweeps through the prominence and damps almost exponentially. We construct a phenomenological model of bulk momentum transfer from the shock to the prominence, which agreed quantitatively with all the simulation results. Based on the phenomenological prominence activation model, we diagnosed physical parameters of the coronal shock wave. The estimated energy of the coronal shock is several percent of the total energy released during the X5.4 flare.« less

Coronal Heating and the Magnetic Flux Content of the Network

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Hathaway, D. H.; Rose, M. Franklin (Technical Monitor)

2001-01-01

Previously, from analysis of SOHO coronal images in combination with Kitt Peak magnetograms, we found that the quiet corona is the sum of two components: the large-scale corona and the coronal network. The large-scale corona consists of all coronal-temperature (T approximately 10(exp 6) K) structures larger than supergranules (greater than approximately 30,000 kilometers). The coronal network (1) consists of all coronal-temperature structures smaller than supergranules, (2) is rooted in and loosely traces the photospheric magnetic network, (3) has its brightest features seated on polarity dividing lines (neutral lines) in the network magnetic flux, and (4) produces only about 5% of the total coronal emission in quiet regions. The heating of the coronal network is apparently magnetic in origin. Here, from analysis of EIT coronal images of quiet regions in combination with magnetograms of the same quiet regions from SOHO/MDI and from Kitt Peak, we examine the other 95% of the quiet corona and its relation to the underlying magnetic network. We find: (1) Dividing the large-scale corona into its bright and dim halves divides the area into bright "continents" and dark "oceans" having spans of 2-4 supergranules. (2) These patterns are also present in the photospheric magnetograms: the network is stronger under the bright half and weaker under the dim half. (3) The radiation from the large-scale corona increases roughly as the cube root of the magnetic flux content of the underlying magnetic network. In contrast, the coronal radiation from an active region increases roughly linearly with the magnetic flux content of the active region. We assume, as is widely held, that nearly all of the large-scale corona is magnetically rooted in the network. Our results suggest that either the coronal heating in quiet regions has a large non-magnetic component, or, if the heating is predominantly produced via the magnetic field, the mechanism is significantly different than in active regions.

Influence of the remaining coronal structure on the resistance of teeth with intraradicular retainer.

PubMed

Pereira, Jefferson Ricardo; Neto, Tatiany de Mendonça; Porto, Vinícius de Carvalho; Pegoraro, Luiz Fernando; do Valle, Accácio Lins

2005-01-01

The aim of this study was to compare the resistance of endodontically treated teeth with intraradicular retainer different amounts of remaining coronal structure. Fifty freshly extracted maxillary canines were endodontically treated and randomly assigned to five groups (n=10), as follows: group 1 (control) = teeth with custom cast post and core; group 2 = teeth without remaining coronal structure; group 3, 4 and 5 = teeth with 1 mm, 2 mm and 3 mm of remaining coronal structure, respectively. All specimens in groups 2 to 5 were restored with prefabricated post and resin core. The teeth were embedded in acrylic resin and the fracture strength was measured on a universal testing machine at 45 degrees to the long axis of the tooth until failure. Data were analyzed statistically by one-way analysis of variance and Tukey's test. There was no significant differences (p>0.05) between the control group and group 2, and between groups 3, 4 and 5 (p>0.05). Control group and group 2 had significantly higher resistance strength than groups 3, 4 and 5 (p<0.00001). The findings of this study showed that teeth without remaining coronal structure had significantly higher fracture strength than those with remaining coronal structure (1 mm, 2 mm and 3 mm). When the dental crown was not completely removed, the amount of remaining coronal dentin did not significantly affect the fracture strength of endodontically treated teeth with intraradicular retainer.

Current Sheet Evolution In The Aftermath Of A CME Event

NASA Technical Reports Server (NTRS)

Bemporad, A.; Poletto, G.; Seuss, S. T.; Schwardron, N. A.; Elliott, H. A.; Raymond, J. C.

2006-01-01

We report on SOHO UVCS observations of the coronal restructuring following a coronal mass ejection (CME) on 2002 November 26, at the time of a SOHO-Ulysses quadrature campaign. Starting about 1.5 hr after a CME in the northwest quadrant, UVCS began taking spectra at 1.7 R, covering emission from both cool and hot plasma. Observations continued, with occasional gaps, for more than 2 days. Emission in the 974.8 A line of [Fe XVIII], indicating temperatures above 6 x 10(exp 6) K, was observed throughout the campaign in a spatially limited location. Comparison with EIT images shows the [Fe XVIII] emission to overlie a growing post-flare loop system formed in the aftermath of the CME. The emission most likely originates in a current sheet overlying the arcade. Analysis of the [Fe XVIII] emission allows us to infer the evolution of physical parameters in the current sheet over the entire span of our observations: in particular, we give the temperature versus time in the current sheet and estimate its density. At the time of the quadrature, Ulysses was directly above the location of the CME and intercepted the ejecta. High ionization state Fe was detected by the Ulysses SWICS throughout the magnetic cloud associated with the CME, although its rapid temporal variation suggests bursty, rather than smooth, reconnection in the coronal current sheet. The SOHO-Ulysses data set provided us with the unique opportunity of analyzing a current sheet structure from its lowest coronal levels out to its in situ properties. Both the remote and in situ observations are compared with predictions of theoretical CME models.

Long-term Spectral Evolution of Tidal Disruption Candidates Selected by Strong Coronal Lines

NASA Astrophysics Data System (ADS)

Yang, Chen-Wei; Wang, Ting-Gui; Ferland, Gary; Yuan, Weimin; Zhou, Hong-Yan; Jiang, Peng

2013-09-01

We present results of follow-up optical spectroscopic Multi-Mirror Telescope (MMT) observations of seven rare, extreme coronal line-emitting galaxies reported by Wang et al. Large variations in coronal lines are found in four objects, making them strong candidates for tidal disruption events (TDEs). For the four TDE candidates, all the coronal lines with ionization states higher than [Fe VII] disappear within 5-9 yr. The [Fe VII] line faded by a factor of about five in one object (J0952+2143) within 4 yr, whereas the line emerged in another two objects that previously did not show the line. A strong increment in the [O III] flux is observed, shifting the line ratios toward the loci of active galactic nuclei on the BPT diagram. Surprisingly, we detect a non-canonical [O III] λ5007/[O III] λ4959 ratio of ~= 2 in two objects, indicating a large column density of O2 + and thus probably optically thick gas. This result also requires a very large ionization parameter and a relatively soft ionizing spectral energy distribution (e.g., a blackbody with T < 5 × 104 K). Our observations can be explained as the echoing of a strong ultraviolet to soft X-ray flare caused by TDEs on molecular clouds in the inner parsecs of the galactic nuclei. Reanalyzing the Sloan Digital Sky Survey spectra reveals double-peaked or strongly blue-shouldered broad lines in three of the objects, which disappeared in the MMT spectra of two objects and faded by a factor of 10 in 8 yr in the remaining object with a decrease in both the line width and centroid offset. We interpret these broad lines as arising from decelerating biconical outflows. Our results demonstrate that the signatures of echoing can persist for as long as 10 yr and can be used to probe the gas environment in quiescent galactic nuclei.

Formation and evolution of coronal rain observed by SDO/AIA on February 22, 2012

NASA Astrophysics Data System (ADS)

Vashalomidze, Z.; Kukhianidze, V.; Zaqarashvili, T. V.; Oliver, R.; Shergelashvili, B.; Ramishvili, G.; Poedts, S.; De Causmaecker, P.

2015-05-01

Context. The formation and dynamics of coronal rain are currently not fully understood. Coronal rain is the fall of cool and dense blobs formed by thermal instability in the solar corona towards the solar surface with acceleration smaller than gravitational free fall. Aims: We aim to study the observational evidence of the formation of coronal rain and to trace the detailed dynamics of individual blobs. Methods: We used time series of the 171 Å and 304 Å spectral lines obtained by the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamic Observatory (SDO) above active region AR 11420 on February 22, 2012. Results: Observations show that a coronal loop disappeared in the 171 Å channel and appeared in the 304 Å line more than one hour later, which indicates a rapid cooling of the coronal loop from 1 MK to 0.05 MK. An energy estimation shows that the radiation is higher than the heat input, which indicates so-called catastrophic cooling. The cooling was accompanied by the formation of coronal rain in the form of falling cold plasma. We studied two different sequences of falling blobs. The first sequence includes three different blobs. The mean velocities of the blobs were estimated to be 50 km s-1, 60 km s-1 and 40 km s-1. A polynomial fit shows the different values of the acceleration for different blobs, which are lower than free-fall in the solar corona. The first and second blob move along the same path, but with and without acceleration, respectively. We performed simple numerical simulations for two consecutive blobs, which show that the second blob moves in a medium that is modified by the passage of the first blob. Therefore, the second blob has a relatively high speed and no acceleration, as is shown by observations. The second sequence includes two different blobs with mean velocities of 100 km s-1 and 90 km s-1, respectively. Conclusions: The formation of coronal rain blobs is connected with the process of catastrophic cooling. The different acceleration of different coronal rain blobs might be due to the different values in the density ratio of blob to corona. All blobs leave trails, which might be a result of continuous cooling in their tails. Two movies attached to Fig. 1 are available in electronic form at http://www.aanda.org

Analysis and modelling of recurrent solar flares observed with Hinode/EIS on March 9, 2012

NASA Astrophysics Data System (ADS)

Polito, V.; Del Zanna, G.; Valori, G.; Pariat, E.; Mason, H. E.; Dudík, J.; Janvier, M.

2017-05-01

Three homologous C-class flares and one last M-class flare were observed by both the Solar Dynamics Observatory (SDO) and the Hinode EUV Imaging Spectrometer (EIS) in the AR 11429 on March 9, 2012. All the recurrent flares occurred within a short interval of time (less than 4 h), showed very similar plasma morphology and were all confined, until the last one when a large-scale eruption occurred. The C-class flares are characterized by the appearance, at approximatively the same locations, of two bright and compact footpoint sources of ≈3-10 MK evaporating plasma, and a semi-circular ribbon. During all the flares, the continuous brightening of a spine-like hot plasma (≈10 MK) structure is also observed. Spectroscopic observations with Hinode/EIS are used to measure and compare the blueshift velocities in the Fe xxiii emission line and the electron number density at the flare footpoints for each flare. Similar velocities, of the order of 150-200 km s-1, are observed during the C2.0 and C4.7 confined flares, in agreement with the values reported by other authors in the study of the last M1.8 class flare. On the other hand, lower electron number densities and temperatures tend to be observed in flares with lower peak soft X-ray flux. In order to investigate the homologous nature of the flares, we performed a non-linear force-free field (NLFFF) extrapolation of the 3D magnetic field configuration in the corona. The NLFFF extrapolation and the Quasi-Separatrix Layers (QSLs) provide the magnetic field context which explains the location of the kernels, spine-like hot plasma and semi-circular brightenings observed in the (non-eruptive) flares. Given the absence of a coronal null point, we argue that the homologous flares were all generated by the continuous recurrence of bald patch reconnection. The movie associated to Fig. 2 is available at http://www.aanda.org

A simple model of chromospheric evaporation and condensation driven conductively in a solar flare

DOE Office of Scientific and Technical Information (OSTI.GOV)

Longcope, D. W.

2014-11-01

Magnetic energy released in the corona by solar flares reaches the chromosphere where it drives characteristic upflows and downflows known as evaporation and condensation. These flows are studied here for the case where energy is transported to the chromosphere by thermal conduction. An analytic model is used to develop relations by which the density and velocity of each flow can be predicted from coronal parameters including the flare's energy flux F. These relations are explored and refined using a series of numerical investigations in which the transition region (TR) is represented by a simplified density jump. The maximum evaporation velocity,more » for example, is well approximated by v{sub e} ≅ 0.38(F/ρ{sub co,} {sub 0}){sup 1/3}, where ρ{sub co,} {sub 0} is the mass density of the pre-flare corona. This and the other relations are found to fit simulations using more realistic models of the TR both performed in this work, and taken from a variety of previously published investigations. These relations offer a novel and efficient means of simulating coronal reconnection without neglecting entirely the effects of evaporation.« less

Three-Dimensional MHD Modeling of The Solar Corona and Solar Wind: Comparison with The Wang-Sheeley Model

NASA Technical Reports Server (NTRS)

Usmanov, A. V.; Goldstein, M. L.

2003-01-01

We present simulation results from a tilted-dipole steady-state MHD model of the solar corona and solar wind and compare the output from our model with the Wang-Sheeley model which relates the divergence rate of magnetic flux tubes near the Sun (inferred from solar magnetograms) to the solar wind speed observed near Earth and at Ulysses. The boundary conditions in our model specified at the coronal base and our simulation region extends out to 10 AU. We assumed that a flux of Alfven waves with amplitude of 35 km per second emanates from the Sun and provides additional heating and acceleration for the coronal outflow in the open field regions. The waves are treated in the WKB approximation. The incorporation of wave acceleration allows us to reproduce the fast wind measurements obtained by Ulysses, while preserving reasonable agreement with plasma densities typically found at the coronal base. We find that our simulation results agree well with Wang and Sheeley's empirical model.

The Mass of a Solar Quiescent Prominence

NASA Technical Reports Server (NTRS)

Low, B. C.; Fong, B.; Fan, Y.

2003-01-01

This paper follows up on our recent paper on the role of prominence mass in the storage of magnetic energy for driving a coronal mass ejection (CME). The previous paper erroneously rejected a set of sheet- prominence solutions, the recovery of which allows for a simple theoretical estimate of the mass of a quiescent prominence. For coronal fields of 5-10 G, these hydromagnetic solutions suggest that a prominence mass of (1-26) x 10(exp 6) g is needed to hold detached magnetic fields of intensity comparable to the coronal fields in an unbounded atmosphere such that the global magnetic field is energetically able to spontaneously open up and still have enough energy to account for the kinetic and gravitational potential energies carried away in a CME. This simple result is discussed in relation to observed prominence magnetic field intensities, densities, and masses, pointing to the relevance of such observations to the question of magnetic energy storage in the solar corona.

Equilibrium models of coronal loops that involve curvature and buoyancy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hindman, Bradley W.; Jain, Rekha, E-mail: hindman@solarz.colorado.edu

2013-12-01

We construct magnetostatic models of coronal loops in which the thermodynamics of the loop is fully consistent with the shape and geometry of the loop. This is achieved by treating the loop as a thin, compact, magnetic fibril that is a small departure from a force-free state. The density along the loop is related to the loop's curvature by requiring that the Lorentz force arising from this deviation is balanced by buoyancy. This equilibrium, coupled with hydrostatic balance and the ideal gas law, then connects the temperature of the loop with the curvature of the loop without resorting to amore » detailed treatment of heating and cooling. We present two example solutions: one with a spatially invariant magnetic Bond number (the dimensionless ratio of buoyancy to Lorentz forces) and the other with a constant radius of the curvature of the loop's axis. We find that the density and temperature profiles are quite sensitive to curvature variations along the loop, even for loops with similar aspect ratios.« less

Enthalpy-Based Thermal Evolution of Loops: III. Comparison of Zero-Dimensional Models

NASA Technical Reports Server (NTRS)

Cargill, P. J.; Bradshaw, Stephen J.; Klimchuk, James A.

2012-01-01

Zero dimensional (0D) hydrodynamic models, provide a simple and quick way to study the thermal evolution of coronal loops subjected to time-dependent heating. This paper presents a comparison of a number of 0D models that have been published in the past and is intended to provide a guide for those interested in either using the old models or developing new ones. The principal difference between the models is the way the exchange of mass and energy between corona, transition region and chromosphere is treated, as plasma cycles into and out of a loop during a heating-cooling cycle. It is shown that models based on the principles of mass and energy conservation can give satisfactory results at some, or, in the case of the Enthalpy Based Thermal Evolution of Loops (EBTEL) model, all stages of the loop evolution. Empirical models can lead to low coronal densities, spurious delays between the peak density and temperature, and, for short heating pulses, overly short loop lifetimes.

The growth of filaments by the condensation of coronal arches

NASA Technical Reports Server (NTRS)

Davis, J. M.; Krieger, A. S.

1982-01-01

A model of filament formation based on the condensation of coronal arches is described. The condensation results from initiating the radiative instability within an arch by superimposing a transient energy supply upon the steady state heating mechanism. The transient energy supply increases the density within the arch so that when it is removed the radiative losses are sufficient to lead to cooling below the minimum in the power loss curve. Times from the initial formation of the condensation to its temperature stabilization as a cool filament have been calculated for various initial conditions. They lie in the range 10,000-100,000 s with the majority of the time spent above a temperature of 1 x 10 to the 6th K. Under the assumption that the condensation of a single arch forms an element of the filament, a complete filament requires the condensation of an arcade of loops. Using experimentally derived parameters, filament densities of 10 to the 11th to 10 to the 12th per cu cm can be obtained.

A parameter study of the two-fluid solar wind

NASA Technical Reports Server (NTRS)

Sandbaek, Ornulf; Leer, Egil; Holzer, Thomas E.

1992-01-01

A two-fluid model of the solar wind was introduced by Sturrock and Hartle (1966) and Hartle and Sturrock (1968). In these studies the proton energy equation was integrated neglecting the heat conductive term. Later several authors solved the equations for the two-fluid solar wind model keeping the proton heat conductive term. Methods where the equations are integrated simultaneously outward and inward from the critical point were used. The equations were also integrated inward from a large heliocentric distance. These methods have been applied to cases with low coronal base electron densities and high base temperatures. In this paper we present a method of integrating the two-fluid solar wind equations using an iteration procedure where the equations are integrated separately and the proton flux is kept constant during the integrations. The technique is applicable for a wide range of coronal base densities and temperatures. The method is used to carry out a parameter study of the two-fluid solar wind.

A comparison of non-local electron transport models relevant to inertial confinement fusion

NASA Astrophysics Data System (ADS)

Sherlock, Mark; Brodrick, Jonathan; Ridgers, Christopher

2017-10-01

We compare the reduced non-local electron transport model developed by Schurtz et al. to Vlasov-Fokker-Planck simulations. Two new test cases are considered: the propagation of a heat wave through a high density region into a lower density gas, and a 1-dimensional hohlraum ablation problem. We find the reduced model reproduces the peak heat flux well in the ablation region but significantly over-predicts the coronal preheat. The suitability of the reduced model for computing non-local transport effects other than thermal conductivity is considered by comparing the computed distribution function to the Vlasov-Fokker-Planck distribution function. It is shown that even when the reduced model reproduces the correct heat flux, the distribution function is significantly different to the Vlasov-Fokker-Planck prediction. Two simple modifications are considered which improve agreement between models in the coronal region. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

TRIGGER MECHANISM OF SOLAR SUBFLARES IN A BRAIDED CORONAL MAGNETIC STRUCTURE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tiwari, Sanjiv K.; Alexander, Caroline E.; Winebarger, Amy R.

Fine-scale braiding of coronal magnetic loops by continuous footpoint motions may power coronal heating via nanoflares, which are spontaneous fine-scale bursts of internal reconnection. An initial nanoflare may trigger an avalanche of reconnection of the braids, making a microflare or larger subflare. In contrast to this internal triggering of subflares, we observe external triggering of subflares in a braided coronal magnetic field observed by the High-resolution Coronal Imager (Hi-C). We track the development of these subflares using 12 s cadence images acquired by SDO/AIA in 1600, 193, 94 Å, and registered magnetograms of SDO/HMI, over four hours centered on the Hi-Cmore » observing time. These data show numerous recurring small-scale brightenings in transition-region emission happening on polarity inversion lines where flux cancellation is occurring. We present in detail an example of an apparent burst of reconnection of two loops in the transition region under the braided coronal field which is appropriate for releasing a short reconnected loop downward and a longer reconnected loop upward. The short loop presumably submerges into the photosphere, participating in observed flux cancellation. A subflare in the overlying braided magnetic field is apparently triggered by the disturbance of the braided field by the reconnection-released upward loop. At least 10 subflares observed in this braided structure appear to be triggered this way. How common this external trigger mechanism for coronal subflares is in other active regions, and how important it is for coronal heating in general, remain to be seen.« less

Toward a Next Generation Solar Coronagraph: Development of a Compact Diagnostic Coronagraph on the ISS

NASA Astrophysics Data System (ADS)

Cho, K.-S.; Bong, S.-C.; Choi, S.; Yang, H.; Kim, J.; Baek, J.-H.; Park, J.; Lim, E.-K.; Kim, R.-S.; Kim, S.; Kim, Y.-H.; Park, Y.-D.; Clarke, S. W.; Davila, J. M.; Gopalswamy, N.; Nakariakov, V. M.; Li, B.; Pinto, R. F.

2017-10-01

The Korea Astronomy and Space Science Institute plans to develop a coronagraph in collaboration with National Aeronautics and Space Administration (NASA) and to install it on the International Space Station (ISS). The coronagraph is an externally occulted one-stage coronagraph with a field of view from 3 to 15 solar radii. The observation wavelength is approximately 400 nm, where strong Fraunhofer absorption lines from the photosphere experience thermal broadening and Doppler shift through scattering by coronal electrons. Photometric filter observations around this band enable the estimation of 2D electron temperature and electron velocity distribution in the corona. Together with a high time cadence (<12 min) of corona images used to determine the geometric and kinematic parameters of coronal mass ejections, the coronagraph will yield the spatial distribution of electron density by measuring the polarized brightness. For the purpose of technical demonstration, we intend to observe the total solar eclipse in August 2017 with the filter system and to perform a stratospheric balloon experiment in 2019 with the engineering model of the coronagraph. The coronagraph is planned to be installed on the ISS in 2021 for addressing a number of questions (e.g., coronal heating and solar wind acceleration) that are both fundamental and practically important in the physics of the solar corona and of the heliosphere.

Plasma Composition in a Sigmoidal Anemone Active Region

NASA Astrophysics Data System (ADS)

Baker, D.; Brooks, D. H.; Démoulin, P.; van Driel-Gesztelyi, L.; Green, L. M.; Steed, K.; Carlyle, J.

2013-11-01

Using spectra obtained by the EUV Imaging Spectrometer (EIS) instrument onboard Hinode, we present a detailed spatially resolved abundance map of an active region (AR)-coronal hole (CH) complex that covers an area of 359'' × 485''. The abundance map provides first ionization potential (FIP) bias levels in various coronal structures within the large EIS field of view. Overall, FIP bias in the small, relatively young AR is 2-3. This modest FIP bias is a consequence of the age of the AR, its weak heating, and its partial reconnection with the surrounding CH. Plasma with a coronal composition is concentrated at AR loop footpoints, close to where fractionation is believed to take place in the chromosphere. In the AR, we found a moderate positive correlation of FIP bias with nonthermal velocity and magnetic flux density, both of which are also strongest at the AR loop footpoints. Pathways of slightly enhanced FIP bias are traced along some of the loops connecting opposite polarities within the AR. We interpret the traces of enhanced FIP bias along these loops to be the beginning of fractionated plasma mixing in the loops. Low FIP bias in a sigmoidal channel above the AR's main polarity inversion line, where ongoing flux cancellation is taking place, provides new evidence of a bald patch magnetic topology of a sigmoid/flux rope configuration.

Observations of absorption lines from highly ionized atoms. [of interstellar medium

NASA Technical Reports Server (NTRS)

Jenkins, Edward B.

1987-01-01

In the ultraviolet spectra of hot stars, absorption lines can be seen from highly ionized species in the interstellar medium. Observations of these features which have been very influential in revising the perception of the medium's various physical states, are discussed. The pervasiveness of O 6 absorption lines, coupled with complementary observations of a diffuse background in soft X-rays and EUV radiation, shows that there is an extensive network of low density gas (n approx. few x 0.001/cu cm) existing at coronal temperatures log T = 5.3 or 6.3. Shocks created by supernova explosions or mass loss from early-type stars can propagate freely through space and eventually transfer a large amount of energy to the medium. To create the coronal temperatures, the shocks must have velocities in excess of 150 km/sec; shocks at somewhat lower velocity (v = 100 km/sec) can be directly observed in the lines of Si3. Observations of other lines in the ultraviolet, such as Si 4V and C 5, may highlight the widespread presence of energetic UV radiation from very hot, dwarf stars. More advanced techniques in visible and X-ray astronomical spectroscopy may open up for inspection selected lines from atoms in much higher stages of ionization.

Observations of Absorption Lines from Highly Ionized Atoms

NASA Technical Reports Server (NTRS)

Jenkins, E. B.

1984-01-01

In the ultraviolet spectra of hot stars, absorption lines can be seen from highly ionized species in the interstellar medium. Observations of these features which have been very influential in revising the perception of the medium's various physical states, are discussed. The pervasiveness of O 6 absorption lines, coupled with complementary observations of a diffuse background in soft X-rays and EUV radiation, shows that there is an extensive network of low density gas (n approx. fewX 0.001/cucm) existing at coronal temperatures, 5.3 or = log T or = 6.3. Shocks created by supernova explosions or mass loss from early-type stars can propagate freely through space and eventually transfer a large amount of energy to the medium. To create the coronal temperatures, the shocks must have velocities in excess of 150 km/sec; shocks at somewhat lower velocity 9v or = 100 km/sec) can be directly observed in the lines of Si3. Observations of other lines in the ultraviolet, such as Si 4V and C 5, may highlight the widespread presence of energetic uv radiation from very hot, dward stars. More advanced techniques in visible and X-ray astronomical spectroscopy may open up for inspection selected lines from atoms in much higher stages of ionization.

Coronal heating by the resonant absorption of Alfven waves - Importance of the global mode and scaling laws

NASA Technical Reports Server (NTRS)

Steinolfson, Richard S.; Davila, Joseph M.

1993-01-01

Numerical simulations of the MHD equations for a fully compressible, low-beta, resistive plasma are used to study the resonance absorption process for the heating of coronal active region loops. Comparisons with more approximate analytic models show that the major predictions of the analytic theories are, to a large extent, confirmed by the numerical computations. The simulations demonstrate that the dissipation occurs primarily in a thin resonance layer. Some of the analytically predicted features verified by the simulations are (a) the position of the resonance layer within the initial inhomogeneity; (b) the importance of the global mode for a large range of loop densities; (c) the dependence of the resonance layer thickness and the steady-state heating rate on the dissipation coefficient; and (d) the time required for the resonance layer to form. In contrast with some previous analytic and simulation results, the time for the loop to reach a steady state is found to be the phase-mixing time rather than a dissipation time. This disagreement is shown to result from neglect of the existence of the global mode in some of the earlier analyses. The resonant absorption process is also shown to behave similar to a classical driven harmonic oscillator.

Coronal Fine Structure in Dynamic Events Observed by Hi-C

NASA Technical Reports Server (NTRS)

Winebarger, Amy; Schuler, Timothy

2013-01-01

The High-Resolution Coronal Imager (Hi-C) flew aboard a NASA sounding rocket on 2012 July 11 and captured roughly 345 s of high spatial and temporal resolution images of the solar corona in a narrowband 193 Angstrom channel. We have analyzed the fluctuations in intensity of Active Region 11520. We selected events based on a lifetime greater than 11 s (two Hi-C frames) and intensities greater than a threshold determined from the photon and readout noise. We compare the Hi-C events with those determined from AIA. We find that HI-C detects shorter and smaller events than AIA. We also find that the intensity increase in the Hi-C events is approx. 3 times greater than the intensity increase in the AIA events we conclude the events are related to linear sub-structure that is unresolved by AIA

Blasting CME

NASA Image and Video Library

2017-12-08

This LASCO C2 image, taken 8 January 2002, shows a widely spreading coronal mass ejection (CME) as it blasts more than a billion tons of matter out into space at millions of kilometers per hour. The C2 image was turned 90 degrees so that the blast seems to be pointing down. An EIT 304 Angstrom image from a different day was enlarged and superimposed on the C2 image so that it filled the occulting disk for effect. Credit: NASA/GSFC/SOHO/ESA To learn more go to the SOHO website: sohowww.nascom.nasa.gov/home.html To learn more about NASA's Sun Earth Day go here: sunearthday.nasa.gov/2010/index.php

Effect of Local Thermal Equilibrium Misbalance on Long-wavelength Slow Magnetoacoustic Waves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakariakov, V. M.; Afanasyev, A. N.; Kumar, S.

Evolution of slow magnetoacoustic waves guided by a cylindrical magnetic flux tube that represents a coronal loop or plume, is modeled accounting for the effects of finite gas pressure, weak nonlinearity, dissipation by thermal conduction and viscosity, and the misbalance between the cooling by optically thin radiation and unspecified heating of the plasma. An evolutionary equation of the Burgers–Malthus type is derived. It is shown that the cooling/heating misbalance, determined by the derivatives of the combined radiative cooling and heating function, with respect to the density, temperature, and magnetic field at the thermal equilibrium affect the wave rather strongly. Thismore » effect may either cause additional damping, or counteract it, or lead to the gradual amplification of the wave. In the latter case, the coronal plasma acts as an active medium for the slow magnetoacoustic waves. The effect of the cooling/heating misbalance could be important for coronal slow waves, and could be responsible for certain discrepancies between theoretical results and observations, in particular, the increased or decreased damping lengths and times, detection of the waves at certain heights only, and excitation of compressive oscillations. The results obtained open up a possibility for the diagnostics of the coronal heating function by slow magnetoacoustic waves.« less

The Connection Between Solar Coronal Cavities and Solar Filaments

NASA Astrophysics Data System (ADS)

Zawadzki, B.; Karna, N.; Prchlik, J.; Reeves, K.; Kempton, D.; Angryk, R.

2017-12-01

Filaments are structures in the solar corona made up of relatively cool, dense, partially ionized plasma. Coronal cavities, circular or elliptical regions of low plasma density, are observed above prominences on the solar limb when viewed in EUV and white light coronal images. Since most filament/cavity eruptions lead to a coronal mass ejection (CME), determining the likelihood of an eruption event will improve our ability to predict space weather. We examine SDO/AIA cavity metadata and HEK filament metadata to determine which cavities are associated with which filaments from 2012 to 2015. Our study involved 140 cavities and 368 filaments that appeared poleward of +-30 degrees. We categorized the cavities and filaments based on the stability of the structures, defined by whether or not the cavity and filament exist long enough to track fully across the solar disk. Using these categories we perform a statistical study on various filament qualities within the metadata. Our findings indicate that filaments with cavities are observed more often at high latitude in compared to filaments without cavities. Moreover, our study indicates that a statistically significant difference exists between the filament length and tilt distributions for certain categories. This work supported by the NSF-REU solar physics program at SAO, grant number AGS-1560313, and the NSF-DIBBS project, grant number ACI-1443061.

Coronal Jets in Closed Magnetic Regions on the Sun

NASA Astrophysics Data System (ADS)

Wyper, Peter Fraser; DeVore, C. R.

2015-04-01

Coronal jets are dynamic, collimated structures observed in solar EUV and X-ray emission. They appear predominantly in the open field of coronal holes, but are also observed in areas of closed field, especially active regions. A common feature of coronal jets is that they originate from the field above a parasitic polarity of opposite sign to the surrounding field. Some process - such as instability onset or flux emergence - induces explosive reconnection between the closed “anemone” field and the surrounding open field that generates the jet. The lesser number of coronal jets in closed-field regions suggests a possible stabilizing effect of the closed configuration with respect to coronal jet formation. If the scale of the jet region is small compared with the background loop length, as in for example type II spicules, the nearby magnetic field may be treated as locally open. As such, one would expect that if a stabilizing effect exists it becomes most apparent as the scale of the anemone region approaches that of the background coronal loops.To investigate if coronal jets are indeed suppressed along shorter coronal loops, we performed a number of simulations of jets driven by a rotation of the parasitic polarity (as in the previous open-jet calculations by Pariat et. al 2009, 2010, 2015) embedded in a large-scale closed bipolar field. The simulations were performed with the state of the art Adaptively Refined Magnetohydrodynamics Solver. We will report here how the magnetic configuration above the anemone region determines the nature of the jet, when it is triggered, and how much of the stored magnetic energy is released. We show that regions in which the background field and the parasitic polarity region are of comparable scale naturally suppress explosive energy release. We will also show how in the post-jet relaxation phase a combination of confined MHD waves and weak current layers are generated by the jet along the background coronal loops, both of which may have implications for coronal heating.This work was supported by an appointment to the NASA Postdoctoral Program (P.F.W.) and by NASA’s Living With a Star Targeted Research and Technology program (C.R.D.).

NEOCE: a new external occulting coronagraph experiment for ultimate observations of the chromosphere, corona and interface

NASA Astrophysics Data System (ADS)

Damé, Luc; Fineschi, Silvano; Kuzin, Sergey; Von Fay-Siebenburgen, Erdélyi Robert

Several ground facilities and space missions are currently dedicated to the study of the Sun at high resolution and of the solar corona in particular. However, and despite significant progress with the advent of space missions and UV, EUV and XUV direct observations of the hot chromosphere and million-degrees coronal plasma, much is yet to be achieved in the understanding of these high temperatures, fine dynamic dissipative structures and of the coronal heating in general. Recent missions have shown the definite role of a wide range of waves and of the magnetic field deep in the inner corona, at the chromosphere-corona interface, where dramatic and physically fundamental changes occur. The dynamics of the chromosphere and corona is controlled and governed by the emerging magnetic field. Accordingly, the direct measurement of the chromospheric and coronal magnetic fields is of prime importance. The solar corona consists of many localised loop-like structures or threads with the plasmas brightening and fading independently. The plasma evolution in each thread is believed to be related to the formation of filaments, each one being dynamic, in a non-equilibrium state. The mechanism sustaining this dynamics, oscillations or waves (Alfvén or other magneto-plasma waves), requires both very high-cadence, multi-spectral observations, and high resolution and coronal magnetometry. This is foreseen in the future Space Mission NEOCE (New External Occulting Coronagraph Experiment), the ultimate new generation high-resolution coronagraphic heliospheric mission, to be proposed for ESA M4. NEOCE, an evolution of the HiRISE mission, is ideally placed at the L5 Lagrangian point (for a better follow-up of CMEs), and provides FUV imaging and spectro-imaging, EUV and XUV imaging and spectroscopy, and ultimate coronagraphy by a remote external occulter (two satellites in formation flying 375 m apart minimizing scattered light) allowing to characterize temperature, densities and velocities up to the solar upper chromosphere, transition zone and inner corona with, in particular, 2D very high resolution multi-spectral imaging-spectroscopy and direct coronal magnetic field measurement: a unique set of tools to understand the structuration and onset of coronal heating. We give a detailed account of the proposed mission profile, and its major scientific objectives and model payload (in particular of the SuperASPIICS package of visible, NIR and UV, Lyman-Alpha and OVI, coronagraphs).

Determination of the structure and heating mechanisms of coronal loops from soft X-ray observations with the solar probe. [grazing incidence telescope

NASA Technical Reports Server (NTRS)

Davis, J. M.; Krieger, A. S.

1978-01-01

High resolution soft X-ray imaging from the solar probe is justified in terms of the expected scientific returns which include the determination of the temperature and density structure of a coronal loop. The advantages of the grazing incidence telescope over the multiple pinhole camera are discussed. An instrument package is described which includes a grazing incidence mirror, a thermal prefilter, a three position filter wheel and a focal plane detector baselined as an 800 by 800 back-illuminated charge coupled device. The structural assembly together with the data processing equipment would draw heavily on the designs being developed for the Solar Polar Mission.

An Investigation of the Large Scale Evolution and Topology of Coronal Mass Ejections in the Solar Wind

NASA Technical Reports Server (NTRS)

Riley, Peter

2000-01-01

This investigation is concerned with the large-scale evolution and topology of coronal mass ejections (CMEs) in the solar wind. During this reporting period we have focused on several aspects of CME properties, their identification and their evolution in the solar wind. The work included both analysis of Ulysses and ACE observations as well as fluid and magnetohydrodynamic simulations. In addition, we analyzed a series of "density holes" observed in the solar wind, that bear many similarities with CMEs. Finally, this work was communicated to the scientific community at three meetings and has led to three scientific papers that are in various stages of review.

Solar X-ray Astronomy Sounding Rocket Program

NASA Technical Reports Server (NTRS)

Moses, J. Daniel

1989-01-01

Several broad objectives were pursued by the development and flight of the High Resolution Soft X-Ray Imaging Sounding Rocket Payload, followed by the analysis of the resulting data and by comparison with both ground based and space based observations from other investigators. The scientific objectives were: to study the thermal equilibrium of active region loop systems by analyzing the X-ray observations to determine electron temperatures, densities, and pressures; by recording the changes in the large scale coronal structures from the maximum and descending phases of Cycle 21 to the ascending phase of Cycle 22; and to extend the study of small scale coronal structures through the minimum of Cycle 21 with new emphasis on correlative observations.

Observational features of equatorial coronal hole jets

NASA Astrophysics Data System (ADS)

Nisticò, G.; Bothmer, V.; Patsourakos, S.; Zimbardo, G.

2010-03-01

Collimated ejections of plasma called "coronal hole jets" are commonly observed in polar coronal holes. However, such coronal jets are not only a specific features of polar coronal holes but they can also be found in coronal holes appearing at lower heliographic latitudes. In this paper we present some observations of "equatorial coronal hole jets" made up with data provided by the STEREO/SECCHI instruments during a period comprising March 2007 and December 2007. The jet events are selected by requiring at least some visibility in both COR1 and EUVI instruments. We report 15 jet events, and we discuss their main features. For one event, the uplift velocity has been determined as about 200 km s-1, while the deceleration rate appears to be about 0.11 km s-2, less than solar gravity. The average jet visibility time is about 30 min, consistent with jet observed in polar regions. On the basis of the present dataset, we provisionally conclude that there are not substantial physical differences between polar and equatorial coronal hole jets.

Preliminary analysis of coronal electron content measurements from spacecraft Helios A around first solar occultation

NASA Technical Reports Server (NTRS)

Edenhofer, P.; Esposito, P. B.; Martin, W. L.; Zygielbaum, A. I.; Hansen, R. T.; Hansen, S. F.; Lueneburg, E.

1977-01-01

Steady-state and dynamical features of the electron density distribution in the solar corona emerge from a preliminary analysis of Helios A electron content measurements. There are strong indications that correlations can be established with earth-bound K-coronagraph measurements.

Inflows in the Inner White-light Corona: The Closing-down of Flux after Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Hess, P.; Wang, Y.-M.

2017-11-01

During times of high solar activity, the Solar and Heliospheric Observatory/Large Angle and Spectrometric Coronagraph C2 coronagraph has recorded multitudes of small features moving inward through its 2{--}6 {R}⊙ field of view. These outer-coronal inflows, which are concentrated around the heliospheric current sheet, tend to be poorly correlated with individual coronal mass ejection (CME) events. Using running-difference movies constructed from Solar Terrestrial Relations Observatory/COR1 coronagraph images taken during 2008-2014, we have identified large numbers of inward-moving features at heliocentric distances below 2 {R}⊙ , with the rate increasing with sunspot and CME activity. Most of these inner-coronal inflows are closely associated with CMEs, being observed during and in the days immediately following the eruptions. Here, we describe several examples of the pinching-off of tapered streamer structures in the wake of CMEs. This type of inflow event is characterized by a separation of the flow into incoming and outgoing components connected by a thin spike, which is interpreted as a continually elongating current sheet viewed edge-on; by the prior convergence of narrow rays toward the current sheet; and by a succession of collapsing loops that form a cusp-shaped structure at the base of the current sheet. The re-forming streamer overlies a growing post-eruption arcade that is visible in EUV images. These observations provide support for standard reconnection models for the formation/evolution of flux ropes during solar eruptive events. We suggest that inflow streams that occur over a relatively wide range of position angles result from the pinching-off of loop arcades whose axes are oriented parallel rather than perpendicular to the sky plane.

Feasibility of self-gated isotropic radial late-phase MR imaging of the liver.

PubMed

Weiss, Jakob; Taron, Jana; Othman, Ahmed E; Grimm, Robert; Kuendel, Matthias; Martirosian, Petros; Ruff, Christer; Schraml, Christina; Nikolaou, Konstantin; Notohamiprodjo, Mike

2017-03-01

To evaluate feasibility of a 3D-isotropic self-gated radial volumetric interpolated breath-hold examination (VIBE) for late-phase MRI of the liver. 70 patients were included and underwent liver MRI at 1.5 T. Depending on the diagnosis, either Gd-EOB-DTPA (35 patients) or gadobutrol (35 patients) were administered. During late (gadobutrol) or hepatocyte-specific phase (Gd-EOB-DTPA), a radial prototype sequence was acquired and reconstructed using (1) self-gating with 40 % acceptance (rVIBE 40 ); (2) with 100 % acceptance of the data (rVIBE 100 ) and compared to Cartesian VIBE (cVIBE). Images were assessed qualitatively (image quality, lesion conspicuity, artefacts; 5-point Likert-scale: 5 = excellent; two independent readers) and quantitatively (coefficient-of-variation (CV); contrast-ratio) in axial and coronal reformations. In eight cases only rVIBE provided diagnostic image quality. Image quality of rVIBE 40 was rated significantly superior (p < 0.05) in Gd-EOB-DTPA-enhanced and coronal reformatted examinations as compared to cVIBE. Lesion conspicuity was significantly improved (p < 0.05) in coronal reformatted Gd-EOB-DTPA-enhanced rVIBE 40 in comparison to cVIBE. CV was higher in rVIBE 40 as compared to rVIBE 100 /cVIBE (p < 0.01). Gadobutrol-enhanced rVIBE 40 and cVIBE showed higher contrast-ratios than rVIBE 100 (p < 0.001), whereas no differences were found in Gd-EOB-DTPA-enhanced examinations. Self-gated 3D-isotropic rVIBE provides significantly superior image quality compared to cVIBE, especially in multiplanar reformatted and Gd-EOB-DTPA-enhanced examinations. • Radial VIBE acquisition reduces motion artefacts. • Gd-EOB-DTPA-enhanced scans provide improved image quality. • Non-diagnostic liver MRI examinations may be reduced by radial k-spaces sampling.

Constraints on particle density evolution within a CME at Mercury

NASA Astrophysics Data System (ADS)

Exner, W.; Liuzzo, L.; Heyner, D.; Feyerabend, M.; Motschmann, U. M.; Glassmeier, K. H.; Shiota, D.; Kusano, K.

2017-12-01

Mercury (RM=2440) is the closest orbiting planet around the Sun and is embedded in an intensive and highly varying solar wind.Mercury's intrinsic dipole with a southward magnetic moment is aligned with the rotation axis and has a northward offset of 0.2 RM.In-situ data from the MESSENGER spacecraft of the magnetic environment near Mercury indicate that a coronal mass ejection (CME) passed the planet on 8 May 2012. The data constrain the direction and magnitude of the CME magnetic field but no information on its particle density could be determined.We apply the hybrid (kinetic ions, electron fluid) code A.I.K.E.F. to study the interaction of Mercury's magnetosphere with the CME.We use MESSENGER magnetic field observations as well as simulation results to constrain the evolution of the particle density inside the CME.We show that within a 24-hour period the particle density within the CME had to vary between 1-100 cm-3 in order to explain MESSENGER magnetic field observations.

Measurements of electron density and temperature profiles in plasma produced by Nike KrF laser for laser plasma instability research

NASA Astrophysics Data System (ADS)

Oh, Jaechul; Weaver, J. L.; Karasik, M.; Chan, L. Y.

2015-08-01

A grid image refractometer (GIR) has been implemented at the Nike krypton fluoride laser facility of the Naval Research Laboratory. This instrument simultaneously measures propagation angles and transmissions of UV probe rays (λ = 263 nm, Δt = 10 ps) refracted through plasma. We report results of the first Nike-GIR measurement on a CH plasma produced by the Nike laser pulse (˜1 ns FWHM) with the intensity of 1.1 × 1015 W/cm2. The measured angles and transmissions were processed to construct spatial profiles of electron density (ne) and temperature (Te) in the underdense coronal region of the plasma. Using an inversion algorithm developed for the strongly refracted rays, the deployed GIR system probed electron densities up to 4 × 1021 cm-3 with the density scale length of 120 μm along the plasma symmetry axis. The resulting ne and Te profiles are verified to be self-consistent with the measured quantities of the refracted probe light.

Comparative Analyses of Two Extremely Fast CMEs Induced Shocks using A H3DMHD Model

NASA Astrophysics Data System (ADS)

Wu, S. T.; Wu, C. C.; Liou, K.; Dryer, Ph D., M.; Plunkett, S. P.

2015-12-01

During the last two decades, spacecraft recorded several extremely fast Coronal Mass Ejections (CMEs) which have resulted in severe geomagnetic storms. Here, we will report results from a comparative study of two extremely fast CME events: one on 29 October 2003 (Halloween 2003 epoch) and the other on 23 July 2012. Both shock events reached 1 AU within ~20 hours. We employed a global three-dimensional (3D) magnetohydrodynamics (MHD) simulation model (H3DMHD, Wu et al. 2007, JGR) to study these two events and compared the results with observations (e.g., 1 AU in-situ data, and coronal images from SOHO/LASCO or STEREO/ SECCHI). It was found that: (i) The peak temperature, velocity, and density of the solar wind for the shock/ICME event are 2 x 107 K, 2500 km s-1, and 35 cm-3, respectively. (ii) The peaks of magnetic field (B) are ~60 and 110 nT for the event on 29 October 2003 and 23 July 2012, respectively. Solar wind densities behind the shocks are extremely low which are due to rarefaction of the interplanetary shocks' propagation. We will discuss this issue in the presentation. Simulations are vastly improved and forecasting arrival times should be done as noted in real time by Zhou and Dryer (Space Weather Quarterly, 2014) review, but CME and B therein is still a major challenge for storm prediction.

The mean coronal magnetic field determined from Helios Faraday rotation measurements

NASA Technical Reports Server (NTRS)

Patzold, M.; Bird, M. K.; Volland, H.; Levy, G. S.; Seidel, B. L.; Stelzried, C. T.

1987-01-01

Coronal Faraday rotation of the linearly polarized carrier signals of the Helios spacecraft was recorded during the regularly occurring solar occultations over almost a complete solar cycle from 1975 to 1984. These measurements are used to determine the average strength and radial variation of the coronal magnetic field at solar minimum at solar distances from 3-10 solar radii, i.e., the range over which the complex fields at the coronal base are transformed into the interplanetary spiral. The mean coronal magnetic field in 1975-1976 was found to decrease with radial distance according to r exp-alpha, where alpha = 2.7 + or - 0.2. The mean field magnitude was 1.0 + or - 0.5 x 10 to the -5th tesla at a nominal solar distance of 5 solar radii. Possibly higher magnetic field strengths were indicated at solar maximum, but a lack of data prevented a statistical determination of the mean coronal field during this epoch.

Large-Scale Coronal Heating, Clustering of Coronal Bright Points, and Concentration of Magnetic Flux

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Hathaway, D. H.

1998-01-01

By combining quiet-region Fe XII coronal images from SOHO/EIT with magnetograms from NSO/Kitt Peak and from SOHO/MDI, we show that on scales larger than a supergranule the population of network coronal bright points and the magnetic flux content of the network are both markedly greater under the bright half of the quiet corona than under the dim half. These results (1) support the view that the heating of the entire corona in quiet regions and coronal holes is driven by fine-scale magnetic activity (microflares, explosive events, spicules) seated low in the magnetic network, and (2) suggest that this large-scale modulation of the magnetic flux and coronal heating is a signature of giant convection cells.

Coronal disturbances and their terrestrial effects /Tutorial Lecture/

NASA Technical Reports Server (NTRS)

Rust, D. M.

1983-01-01

An assessment is undertaken of recent approaches to the prediction of the interplanetary consequences of coronal disturbances, with attention to the relationships of shocks and energetic particles to coronal transients, of proton events to gamma-ray and microwave bursts, of geomagnetic storms to filament eruptions, and of solar wind increases to the flare site magnetic field direction. A discussion is given concerning the novel phenomenon of transient coronal holes, which appear astride the long decay enhancements of 2-50 A X-ray emission following H-alpha filament eruptions. These voids in the corona are similar to long-lived coronal holes, which are the sources of high speed solar wind streams. The transient coronal holes may also be associated with transient solar wind speed increases.

Prominence Bubbles and Plumes: Thermo-magnetic Buoyancy in Coronal Cavity Systems

NASA Astrophysics Data System (ADS)

Berger, Thomas; Hurlburt, N.

2009-05-01

The Hinode/Solar Optical Telescope continues to produce high spatial and temporal resolution images of solar prominences in both the Ca II 396.8 nm H-line and the H-alpha 656.3 nm line. Time series of these images show that many quiescent prominences produce large scale (50 Mm) dark "bubbles" that "inflate" into, and sometimes burst through, the prominence material. In addition, small-scale (2--5 Mm) dark plumes are seen rising into many quiescent prominences. We show typical examples of both phenomena and argue that they originate from the same mechanism: concentrated and heated magnetic flux that rises due to thermal and magnetic buoyancy to equilibrium heights in the prominence/coronal-cavity system. More generally, these bubbles and upflows offer a source of both magnetic flux and mass to the overlying coronal cavity, supporting B.C. Low's theory of CME initiation via steadily increasing magnetic buoyancy breaking through the overlying helmut streamer tension forces. Quiescent prominences are thus seen as the lowermost parts of the larger coronal cavity system, revealing through thermal effects both the cooled downflowing "drainage" from the cavity and the heated upflowing magnetic "plasmoids" supplying the cavity. We compare SOT movies to new 3D compressible MHD simulations that reproduce the dark turbulent plume dynamics to establish the magnetic and thermal character of these buoyancy-driven flows into the corona.

The Slowly Varying Corona. I. Daily Differential Emission Measure Distributions Derived from EVE Spectra

NASA Astrophysics Data System (ADS)

Schonfeld, S. J.; White, S. M.; Hock-Mysliwiec, R. A.; McAteer, R. T. J.

2017-08-01

Daily differential emission measure (DEM) distributions of the solar corona are derived from spectra obtained by the Extreme-ultraviolet Variability Experiment (EVE) over a 4 yr period starting in 2010 near solar minimum and continuing through the maximum of solar cycle 24. The DEMs are calculated using six strong emission features dominated by Fe lines of charge states viii, ix, xi, xii, xiv, and xvi that sample the nonflaring coronal temperature range 0.3-5 MK. A proxy for the non-Fe xviii emission in the wavelength band around the 93.9 Å line is demonstrated. There is little variability in the cool component of the corona (T < 1.3 MK) over the 4 yr, suggesting that the quiet-Sun corona does not respond strongly to the solar cycle, whereas the hotter component (T > 2.0 MK) varies by more than an order of magnitude. A discontinuity in the behavior of coronal diagnostics in 2011 February-March, around the time of the first X-class flare of cycle 24, suggests fundamentally different behavior in the corona under solar minimum and maximum conditions. This global state transition occurs over a period of several months. The DEMs are used to estimate the thermal energy of the visible solar corona (of order 1031 erg), its radiative energy loss rate ((2.5-8) × {10}27 erg s-1), and the corresponding energy turnover timescale (about an hour). The uncertainties associated with the DEMs and these derived values are mostly due to the coronal Fe abundance and density and the CHIANTI atomic line database.

Mass-Loss Evolution in the EUV Low Corona from SDO/AIA Data

NASA Astrophysics Data System (ADS)

López, Fernando M.; Hebe Cremades, M.; Nuevo, Federico A.; Balmaceda, Laura A.; Vásquez, Alberto M.

2017-01-01

We carry out an analysis of the mass that is ejected from three coronal dimming regions observed by the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory. The three events are unambiguously identified with white-light coronal mass ejections (CMEs) that are associated in turn with surface activity of diverse nature: an impulsive (M-class) flare, a weak (B-class) flare, and a filament eruption without a flare. The use of three AIA coronal passbands allows applying a differential emission measure technique to define the dimming regions and identify their ejected mass through the analysis of the electronic density depletion associated with the eruptions. The temporal evolution of the mass loss from the three dimmings can be approximated by an exponential equation followed by a linear fit. We determine the mass of the associated CMEs from COR2 data. The results show that the ejected masses from the low corona represent a considerable amount of the CME mass. We also find that plasma is still being ejected from the low corona at the time when the CMEs reach the COR2 field of view. The temporal evolution of the angular width of the CMEs, of the dimming regions in the low corona, and of the flux registered by GOES in soft X-rays are all in close relation with the behavior of mass ejection from the low corona. We discuss the implications of our findings toward a better understanding of the temporal evolution of several parameters associated with the analyzed dimmings and CMEs.

Formation of a White-Light Jet Within a Quadrupolar Magnetic Configuration

NASA Astrophysics Data System (ADS)

Filippov, Boris; Koutchmy, Serge; Tavabi, Ehsan

2013-08-01

We analyze multi-wavelength and multi-viewpoint observations of a large-scale event viewed on 7 April 2011, originating from an active-region complex. The activity leads to a white-light jet being formed in the outer corona. The topology and evolution of the coronal structures were imaged in high resolution using the Atmospheric Imaging Assembly (AIA) onboard the Solar Dynamics Observatory (SDO). In addition, large field-of-view images of the corona were obtained using the Sun Watcher using Active Pixel System detector and Image Processing (SWAP) telescope onboard the PRoject for Onboard Autonomy (PROBA2) microsatellite, providing evidence for the connectivity of the coronal structures with outer coronal features that were imaged with the Large Angle Spectrometric Coronagraph (LASCO) C2 on the S olar and Heliospheric Observatory (SOHO). The data sets reveal an Eiffel-tower type jet configuration extending into a narrow jet in the outer corona. The event starts from the growth of a dark area in the central part of the structure. The darkening was also observed in projection on the disk by the Solar TErrestrial RElations Observatory-Ahead (STEREO-A) spacecraft from a different point of view. We assume that the dark volume in the corona descends from a coronal cavity of a flux rope that moved up higher in the corona but still failed to erupt. The quadrupolar magnetic configuration corresponds to a saddle-like shape of the dark volume and provides a possibility for the plasma to escape along the open field lines into the outer corona, forming the white-light jet.

Vertical Oscillation of a Coronal Cavity Triggered by an EUV Wave

NASA Astrophysics Data System (ADS)

Zhang, Q. M.; Ji, H. S.

2018-06-01

In this paper, we report our multiwavelength observations of the vertical oscillation of a coronal cavity on 2011 March 16. The elliptical cavity with an underlying horn-like quiescent prominence was observed by the Atmospheric Imaging Assembly on board the Solar Dynamics Observatory. The width and height of the cavity are 150″ and 240″, and the centroid of cavity is 128″ above the solar surface. At ∼17:50 UT, a C3.8 two-ribbon flare took place in active region 11169 close to the solar western limb. Meanwhile, a partial halo coronal mass ejection erupted and propagated at a linear speed of ∼682 km s‑1. Associated with the eruption, a coronal extreme-ultraviolet (EUV) wave was generated and propagated in the northeast direction at a speed of ∼120 km s‑1. Once the EUV wave arrived at the cavity from the top, it pushed the large-scale overlying magnetic field lines downward before bouncing back. At the same time, the cavity started to oscillate coherently in the vertical direction and lasted for ∼2 cycles before disappearing. The amplitude, period, and damping time are 2.4–3.5 Mm, 29–37 minutes, and 26–78 minutes, respectively. The vertical oscillation of the cavity is explained by a global standing MHD wave of fast kink mode. To estimate the magnetic field strength of the cavity, we use two independent methods of prominence seismology. It is found that the magnetic field strength is only a few Gauss and less than 10 G.

CORONAL MAGNETIC FIELDS DERIVED FROM SIMULTANEOUS MICROWAVE AND EUV OBSERVATIONS AND COMPARISON WITH THE POTENTIAL FIELD MODEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyawaki, Shun; Nozawa, Satoshi; Iwai, Kazumasa

2016-02-10

We estimated the accuracy of coronal magnetic fields derived from radio observations by comparing them to potential field calculations and the differential emission measure measurements using EUV observations. We derived line-of-sight components of the coronal magnetic field from polarization observations of the thermal bremsstrahlung in the NOAA active region 11150, observed around 3:00 UT on 2011 February 3 using the Nobeyama Radioheliograph at 17 GHz. Because the thermal bremsstrahlung intensity at 17 GHz includes both chromospheric and coronal components, we extracted only the coronal component by measuring the coronal emission measure in EUV observations. In addition, we derived only themore » radio polarization component of the corona by selecting the region of coronal loops and weak magnetic field strength in the chromosphere along the line of sight. The upper limits of the coronal longitudinal magnetic fields were determined as 100–210 G. We also calculated the coronal longitudinal magnetic fields from the potential field extrapolation using the photospheric magnetic field obtained from the Helioseismic and Magnetic Imager. However, the calculated potential fields were certainly smaller than the observed coronal longitudinal magnetic field. This discrepancy between the potential and the observed magnetic field strengths can be explained consistently by two reasons: (1) the underestimation of the coronal emission measure resulting from the limitation of the temperature range of the EUV observations, and (2) the underestimation of the coronal magnetic field resulting from the potential field assumption.« less

Repeated Structures Found After the Solar Maximum in the Butterfly Diagrams of Coronal Holes

NASA Astrophysics Data System (ADS)

Hofer, M. Y.; Storini, M.

2003-09-01

The influence of the solar cycle evolution on the coronal hole space-time distribution is well known, for polar as well as for equatorial isolated sources of high speed solar wind. Among them the long-lived coronal holes occurrence from the sunspot cycle 21 on is investigated, using the coronal hole catalogue based on HeI (1083 nm) observations (Sanchez-Ibarra and Barraza-Paredes). In at least these two solar cycles (n. 21 and n. 22) a similar structure in the latitude-time diagram of coronal holes is found. The area occurs shortly after the solar maximum at around ~35° heliolatitude and consists of over several Carrington Rotations stable coronal holes (>5 Carr. Rot.s). The diagonal disappears 2-3 years later at the helioequator. Furthermore, the analysis results in a close relation between long-lived isolated coronal holes and the soft X-class flares.

A simple method to estimate restoration volume as a possible predictor for tooth fracture.

PubMed

Sturdevant, J R; Bader, J D; Shugars, D A; Steet, T C

2003-08-01

Many dentists cite the fracture risk posed by a large existing restoration as a primary reason for their decision to place a full-coverage restoration. However, there is poor agreement among dentists as to when restoration placement is necessary because of the inability to make objective measurements of restoration size. The purpose of this study was to compare a new method to estimate restoration volumes in posterior teeth with analytically determined volumes. True restoration volume proportion (RVP) was determined for 96 melamine typodont teeth: 24 each of maxillary second premolar, mandibular second premolar, maxillary first molar, and mandibular first molar. Each group of 24 was subdivided into 3 groups to receive an O, MO, or MOD amalgam preparation design. Each preparation design was further subdivided into 4 groups of increasingly larger size. The density of amalgam used was calculated according to ANSI/ADA Specification 1. The teeth were weighed before and after restoration with amalgam. Restoration weight was calculated, and the density of amalgam was used to calculate restoration volume. A liquid pycnometer was used to calculate coronal volume after sectioning the anatomic crown from the root horizontally at the cementoenamel junction. True RVP was calculated by dividing restoration volume by coronal volume. An occlusal photograph and a bitewing radiograph were made of each restored tooth to provide 2 perpendicular views. Each image was digitized, and software was used to measure the percentage of the anatomic crown restored with amalgam. Estimated RVP was calculated by multiplying the percentage of the anatomic crown restored from the 2 views together. Pearson correlation coefficients were used to compare estimated RVP with true RVP. The Pearson correlation coefficient of true RVP with estimated RVP was 0.97 overall (P

Faraday Rotation as a Probe of Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Kooi, J. E.; Spangler, S. R.; Kassim, N. E.

2016-12-01

Coronal mass ejections (CMEs) are large-scale eruptions of plasma from the Sun that play an important role in space weather. Although CMEs have been an active field of research since their discovery in the 1970s, there is still much to understand about the plasma structure of CMEs. Faraday rotation (FR) is the rotation of the plane of polarization that results when a linearly polarized signal passes through a magnetized plasma such as a CME. FR observations of a source near the Sun can provide information on the plasma structure of a CME shortly after launch. We made sensitive Very Large Array (VLA) full-polarization observations in August, 2012, using 1 — 2 GHz frequencies of a "constellation" of radio sources through the solar corona at heliocentric distances that ranged from 6 — 15 solar radii. Of the nine sources observed, three were occulted by CMEs. In addition to our radioastronomical observations, which represent one of the first active hunts for CME Faraday rotation since Bird et al. (1985) and the first active hunt using the VLA, we obtained white-light coronagraph images from the LASCO/C3 instrument to determine the Thomson scattering brightness, BT, providing a means to independently estimate the plasma density and determine its contribution to the observed Faraday rotation. A constant density force-free flux rope embedded in the background corona was used to model the effects of the CMEs on BT and FR. The single flux rope model successfully reproduces the observed BT and FR profiles for two sources. The third source (0843+1547) was occulted by two CMEs and, therefore, we modeled observations of this source using two flux ropes embedded in the background corona. The two flux rope model successfully reproduces both BT and FR profiles for 0843+1547 and, in particular, the two flux rope model successfully replicates the appropriate slope in FR before and after occultation by the second CME and predicts the observed change in sign to FR > 0 at the end of the observing session. The plasma densities (6 — 22 × 103 cm-3) and axial magnetic field strengths (2 — 12 mG) inferred from our models are consistent with the modeling work of Liu et al. (2007) and Jensen et al. (2008), as well as previous CME FR observations by Bird et al. (1985). This work was supported at the University of Iowa by grant ATM09-56901.

Numerical Simulation of DC Coronal Heating

NASA Astrophysics Data System (ADS)

Dahlburg, Russell B.; Einaudi, G.; Taylor, Brian D.; Ugarte-Urra, Ignacio; Warren, Harry; Rappazzo, A. F.; Velli, Marco

2016-05-01

Recent research on observational signatures of turbulent heating of a coronal loop will be discussed. The evolution of the loop is is studied by means of numerical simulations of the fully compressible three-dimensional magnetohydrodynamic equations using the HYPERION code. HYPERION calculates the full energy cycle involving footpoint convection, magnetic reconnection, nonlinear thermal conduction and optically thin radiation. The footpoints of the loop magnetic field are convected by random photospheric motions. As a consequence the magnetic field in the loop is energized and develops turbulent nonlinear dynamics characterized by the continuous formation and dissipation of field-aligned current sheets: energy is deposited at small scales where heating occurs. Dissipation is non-uniformly distributed so that only a fraction of thecoronal mass and volume gets heated at any time. Temperature and density are highly structured at scales which, in the solar corona, remain observationally unresolved: the plasma of the simulated loop is multi thermal, where highly dynamical hotter and cooler plasma strands are scattered throughout the loop at sub-observational scales. Typical simulated coronal loops are 50000 km length and have axial magnetic field intensities ranging from 0.01 to 0.04 Tesla. To connect these simulations to observations the computed number densities and temperatures are used to synthesize the intensities expected in emission lines typically observed with the Extreme ultraviolet Imaging Spectrometer (EIS) on Hinode. These intensities are then employed to compute differential emission measure distributions, which are found to be very similar to those derived from observations of solar active regions.

Effect of aging on the microstructure, hardness and chemical composition of dentin.

PubMed

Montoya, C; Arango-Santander, S; Peláez-Vargas, A; Arola, D; Ossa, E A

2015-12-01

Understanding the effects of biological aging on human tissues has been a topic of extensive research. With the increase in healthy seniors and quality of life that topic is becoming increasingly important. In this investigation the effects of aging on the microstructure, chemical composition and hardness of human coronal dentin was studied from a comparison of teeth within "young" and "old" age groups. The microstructure of dentin within three regions (i.e., inner, middle and outer) was analyzed using electron and optical microscopy. The mineral-to-collagen ratio in these three regions was estimated using Raman spectroscopy and the hardness was evaluated using microindentation. Results showed that there were significant differences in tubule density, tubule diameter and peritubular cuff diameter with depth. Although there was no difference in tubule density and diameter of the tubules between the age groups, there was a significant difference in the occlusion ratio. A significant increase in hardness between young and old patients was found for middle and outer dentin. An increase in mineral-to-collagen ratio from inner to outer dentin was also found for both groups. In old patients, an increase in mineral content was found in outer coronal dentin as a consequence of tubule occlusion. An increase in occlusion ratio, hardness, and mineral content was found in the dentin of adult patients with age. This increase is most evident in the outer coronal dentin. Copyright © 2015 Elsevier Ltd. All rights reserved.

Observable Signatures of Energy Release in Braided Coronal Loops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pontin, D. I.; Janvier, M.; Tiwari, S. K.

We examine the turbulent relaxation of solar coronal loops containing non-trivial field line braiding. Such field line tangling in the corona has long been postulated in the context of coronal heating models. We focus on the observational signatures of energy release in such braided magnetic structures using MHD simulations and forward modeling tools. The aim is to answer the following question: if energy release occurs in a coronal loop containing braided magnetic flux, should we expect a clearly observable signature in emissions? We demonstrate that the presence of braided magnetic field lines does not guarantee a braided appearance to themore » observed intensities. Observed intensities may—but need not necessarily—reveal the underlying braided nature of the magnetic field, depending on the degree and pattern of the field line tangling within the loop. However, in all cases considered, the evolution of the braided loop is accompanied by localized heating regions as the loop relaxes. Factors that may influence the observational signatures are discussed. Recent high-resolution observations from Hi-C have claimed the first direct evidence of braided magnetic fields in the corona. Here we show that both the Hi-C data and some of our simulations give the appearance of braiding at a range of scales.« less

Heating by transverse waves in simulated coronal loops

NASA Astrophysics Data System (ADS)

Karampelas, K.; Van Doorsselaere, T.; Antolin, P.

2017-08-01

Context. Recent numerical studies of oscillating flux tubes have established the significance of resonant absorption in the damping of propagating transverse oscillations in coronal loops. The nonlinear nature of the mechanism has been examined alongside the Kelvin-Helmholtz instability, which is expected to manifest in the resonant layers at the edges of the flux tubes. While these two processes have been hypothesized to heat coronal loops through the dissipation of wave energy into smaller scales, the occurring mixing with the hotter surroundings can potentially hide this effect. Aims: We aim to study the effects of wave heating from driven and standing kink waves in a coronal loop. Methods: Using the MPI-AMRVAC code, we perform ideal, three dimensional magnetohydrodynamic (MHD) simulations of both (a) footpoint driven and (b) free standing oscillations in a straight coronal flux tube, in the presence of numerical resistivity. Results: We have observed the development of Kelvin-Helmholtz eddies at the loop boundary layer of all three models considered here, as well as an increase of the volume averaged temperature inside the loop. The main heating mechanism in our setups was Ohmic dissipation, as indicated by the higher values for the temperatures and current densities located near the footpoints. The introduction of a temperature gradient between the inner tube and the surrounding plasma, suggests that the mixing of the two regions, in the case of hotter environment, greatly increases the temperature of the tube at the site of the strongest turbulence, beyond the contribution of the aforementioned wave heating mechanism. Three movies associated to Fig. 1 are available in electronic form at http://www.aanda.org

Hanle-Zeeman Scattering Matrix for Magnetic Dipole Transitions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Megha, A.; Sampoorna, M.; Nagendra, K. N.

2017-06-01

The polarization of the light that is scattered by the coronal ions is influenced by the anisotropic illumination from the photosphere and the magnetic field structuring in the solar corona. The properties of the coronal magnetic fields can be well studied by understanding the polarization properties of coronal forbidden emission lines that arise from magnetic dipole ( M 1) transitions in the highly ionized atoms that are present in the corona. We present the classical scattering theory of the forbidden lines for a more general case of arbitrary-strength magnetic fields. We derive the scattering matrix for M 1 transitions usingmore » the classical magnetic dipole model of Casini and Lin and applying the scattering matrix approach of Stenflo. We consider a two-level atom model and neglect collisional effects. The scattering matrix so derived is used to study the Stokes profiles formed in coronal conditions in those regions where the radiative excitations dominate collisional excitations. To this end, we take into account the integration over a cone of an unpolarized radiation from the solar disk incident on the scattering atoms. Furthermore, we also integrate along the line of sight to calculate the emerging polarized line profiles. We consider radial and dipole magnetic field configurations and spherically symmetric density distributions. For our studies we adopt the atomic parameters corresponding to the [Fe xiii] 10747 Å coronal forbidden line. We also discuss the nature of the scattering matrix for M 1 transitions and compare it with that for the electric dipole ( E 1) transitions.« less

Combined metopic and unilateral coronal synostoses: a phenotypic conundrum.

PubMed

Sauerhammer, Tina M; Patel, Kamlesh; Oh, Albert K; Proctor, Mark R; Mulliken, John B; Rogers, Gary F

2014-03-01

Most types of craniosynostosis cause predictable changes in cranial shape. However, the phenotype of combined metopic and unilateral coronal synostoses is anomalous. The purpose of this observational study was to better clarify the clinical and radiographic features of this rare entity. A retrospective review of a craniofacial database was performed. Patients with combined metopic and unilateral coronal synostoses were included in this study. Data collected included demographic information, physical and radiographic findings, genetic evaluation, treatment, and operative outcomes. Of 687 patients treated between 1989 and 2010, only 3 patients had combined metopic and unilateral coronal synostoses. All patients were diagnosed through computed tomography on the first day of life. Phenotypic features included the following: (1) narrowed forehead with a prominent midline ridge, (2) severe bilateral brow retrusion with an acute indentation on the side of the patient coronal suture, (3) facial and nasal angulation similar to isolated unilateral coronal synostosis, and (4) anterior displacement of the ear on the fused side. In addition, the cranial vertex was deviated toward the side of the open coronal suture. Two patients had a head circumference below the 25th percentile; 2 of the 3 had a TWIST gene mutation consistent with Saethre-Chotzen syndrome. One patient was managed through fronto-orbital advancement and required a revision. The other 2 patients had early endoscopic release, followed by postoperative helmet therapy; one improved but still required open cranial remodeling. The other has near-normal phenotype, and no further surgery is planned. Combined metopic and unilateral coronal synostoses present a rare and unusual phenotype. Although early intervention improves the deformity, revisional procedures are usually required.

Age and paragenesis of mineralisation at Coronation Hill uranium deposit, Northern Territory, Australia

NASA Astrophysics Data System (ADS)

Orth, Karin; Meffre, Sebastien; Davidson, Garry

2014-06-01

Coronation Hill is a U + Au + platinum group elements deposit in the South Alligator Valley (SAV) field in northern Australia, south of the better known unconformity-style U East Alligator Rivers (EAR) field. The SAV field differs from the EAR by having a more complex basin-basement architecture. A volcanically active fault trough (Jawoyn Sub-basin) developed on older basement and then was disrupted by renewed faulting, before being buried beneath regional McArthur Basin sandstones that are also the main hanging wall to the EAR deposits. Primary mineralisation at Coronation Hill formed at 1607 ± 26 Ma (rather than 600-900 Ma as previously thought), and so it is likely that the SAV was part of a single west McArthur Basin dilational event. Most ore is hosted in sub-vertical faults and breccias in the competent volcanic cover sequence. This favoured fluid mixing, acid buffering (forming illite) and oxidation of Fe2+ and reduced C-rich assemblages as important uranium depositional mechanisms. However, reduction of U in fractured older pyrite (Pb model age of 1833 ± 67 Ma) is an important trap in diorite. Some primary ore was remobilised at 675 ± 21 Ma to form coarse uraninite + Ni-Co pyrite networks containing radiogenic Pb. Coronation Hill is polymetallic, and in this respect resembles the `egress'-style U deposits in the Athabascan Basin (Canada). However, these are all cover-hosted. A hypothesis for further testing is that Coronation Hill is also egress-style, with ores formed by fluids rising through basement-hosted fault networks (U reduction by diorite pyrite and carbonaceous shale), and into veins and breccias in the overlying Jawoyn Sub-basin volcano-sedimentary succession.

First results from the Citizen CATE Experiment from August 2017

NASA Astrophysics Data System (ADS)

Penn, Matthew; Citizen CATE Experiment 2017 Team

2018-01-01

The Citizen Continental-America Telescopic Eclipse Experiment deployed 68 identical telescope/detector systems across the path of totality for the August 2017 solar eclipse. The sites were located from Oregon to South Carolina, and while at any one site the solar corona was observed for just 2 minutes, the combined data set reveals evolution of the corona for 93 minutes of time. CATE aims to measure the acceleration of the fast solar wind in polar plumes, which is currently unknown as the inner solar corona is not observed from space and difficult to observe at high signal to noise from the ground. With radial velocities ranging from 1 to 100 km/s, density enhancements in the wind in the polar plumes should be observed to move across the CATE field of view in about 1 hour.On 21 Aug 2017, the CATE network had fantastic luck, collecting data from more than 56 of the 68 sites, and excellent data was collected at the first and last sites, maximizing the time coverage. Several of the volunteers from 27 universities, 22 high schools and 19 amateur astronomers uploaded one high-dynamic range image on eclipse day and an initial movie of the coronal evolution has been made (https://citizencate.org ). Polar plumes are observed in the CATE data to the edge of the field above both north and south polar coronal holes. Slow evolution of low-lying coronal loops is seen, and large-scale motions are visible in a coronal streamer on the south-east solar limb. An ejection event is observed in the southern coronal hole, but with just 1% of the data analyzed so far, the signal to noise ratio is currently not sufficient to track steady solar wind flows.CATE was funded with a collaboration of federal, corporate and private groups. CATE training was funded by NASA, and CATE equipment was funded by Daystar, Mathworks, Celestron, colorMaker, NSF and a dozen smaller donors. The funding was organized so that all 68 CATE groups are keeping their equipment, and CATE is now seeking other types of citizen science projects in astronomy. Please bring your project ideas to the talk!

FE analysis of conceptual hybrid composite endodontic post designs in anterior teeth.

PubMed

Gloria, Antonio; Maietta, Saverio; Martorelli, Massimo; Lanzotti, Antonio; Watts, David C; Ausiello, Pietro

2018-04-24

To assess conceptual designs of dental posts consisting of polyetherimide (PEI) reinforced with carbon (C) and glass (G) glass fibers in endodontically treated anterior teeth. 3D tessellated CAD and geometric models of endodontically treated anterior teeth were generated from Micro-CT scan images. Model C-G/PEI composite posts with different Young's moduli were analyzed by Finite Element (FE) methods post A (57.7GPa), post B (31.6GPa), post C (from 57.7 to 9.0GPa in the coronal-apical direction). A load of 50N was applied at 45° to the longitudinal axis of the tooth, acting on the palatal surface of the crown. The maximum principal stress distribution was determined along the post and at the interface between the post and the surrounding structure. Post C, with Young's modulus decreasing from 57.7 to 9.0GPa in the coronal-apical direction, reduced the maximum principal stress distribution in the restored tooth. Post C gave reduced stress and the most uniform stress distribution with no stress concentration, compared to the other C-G/PEI composite posts. The FE analysis confirmed the ability of the functionally graded post to dissipate stress from the coronal to the apical end. Hence actual (physical) C-G/PEI posts could permit optimization of stress distributions in endodontically treated anterior teeth. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.

EUV Dimmings as a Diagnostic of CMEs and Related Phenomena

NASA Technical Reports Server (NTRS)

Thompson, Barbara J.; Mays, M. Leila; Webb, David F.; West, Matthew J.

2012-01-01

Large-scale coronal EUV dimmings, developing on timescaJes of minutes to hours in association with a flare or filament eruption, are known to exhibit a high correlation with coronal mass ejections. While most observations indicate that the decrease in emission in a dimming is due, at least in part, to a density decrease, a complete understanding requires us to examine at least four mechanisms that have been observed to cause darkened regions in the corona: 1) mass loss, 2) cooling, 3) heating, and 4) absorption/obscuration. Recent advances in automatic detection, observations with improved cadence and resolution, multi-viewpoint imaging, and spectroscopic studies have continued to shed light on dimming formation, evolution, and recovery. However, there are still some outstanding questions, including 1) Why do some CMEs show dimming and some do not? 2) What determines the location of a dimming? 3) What determines the temporal evolution of a dimming? 4) How does the post-eruption dimming connect to the ICME? 5) What is the relationship between dimmings and other CME-associated phenomena? The talk will emphasize the different formation mechanisms of dimmings and their relationship to CMEs and CME-associated phenomena.

The evolution of active region loop plasma

NASA Technical Reports Server (NTRS)

Krall, K. R.; Antiochos, S. K.

1980-01-01

The adjustment of coronal active-region loops to changes in their heating rate is investigated numerically. The one-dimensional hydrodynamic equations are solved subject to boundary conditions in which heat flux-induced mass exchange between coronal and chromospheric components is allowed. The calculated evolution of physical parameters suggests that (1) mass supplied during chromospheric evaporation is much more effective in moderating coronal temperature excursions than when downward heat flux is dissipated by a static chromosphere, and (2) the method by which the chromosphere responds to changing coronal conditions can significantly influence coronal readjustment time scales. Observations are cited which illustrate the range of possible fluctuations in the heating rates.

Sources of magnetic fields in recurrent interplanetary streams

NASA Technical Reports Server (NTRS)

Burlaga, L. F.; Behannon, K. W.; Hansen, S. F.; Pneuman, G. W.; Feldman, W. C.

1977-01-01

The sources of magnetic fields in recurrent streams were examined. Most fields and plasmas at 1 AU were related to coronal holes, and the magnetic field lines were open in those holes. Some of the magnetic fields and plasmas were related to open field line regions on the sun which were not associated with known coronal holes, indicating that open field lines are more basic than coronal holes as sources of the solar wind. Magnetic field intensities in five equatorial coronal holes ranged from 2G to 18G. Average measured photospheric magnetic fields along the footprints of the corresponding unipolar fields on circular equatorial arcs at 2.5 solar radii had a similar range and average, but in two cases the intensities were approximately three times higher than the projected intensities. The coronal footprints of the sector boundaries on the source surface at 2.5 solar radii, meandered between -45 deg and +45 deg latitude, and their inclination ranged from near zero to near ninety degrees.

Anomalously low C{sup 6+}/C{sup 5+} ratio in solar wind: ACE/SWICS observation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, L., E-mail: lzh@umich.edu; Landi, E.; Kocher, M.

The Carbon and Oxygen ionization states in the solar wind plasma freeze-in within 2 solar radii (R{sub s}) from the solar surface, and then they do not change as they propagate with the solar wind into the heliosphere. Therefore, the O{sup 7+}/O{sup 6+} and C{sup 6+}/C{sup 5+} charge state ratios measured in situ maintain a record of the thermal properties (electron temperature and density) of the inner corona where the solar wind originates. Since these two ratios freeze-in at very similar height, they are expected to be correlated. However, an investigation of the correlation between these two ratios as measuredmore » by ACE/SWICS instrument from 1998 to 201l shows that there is a subset of “Outliers” departing from the expected correlation. We find about 49.4% of these Outliers is related to the Interplanetary Coronal Mass Ejections (ICMEs), while 49.6% of them is slow speed wind (V{sub p} < 500 km/s) and about 1.0% of them is fast solar wind (V{sub p} > 500 km/s). We compare the outlier-slow-speed wind with the normal slow wind (defined as V{sub p} < 500 km/s and O{sup 7+}/O{sup 6+} > 0.2) and find that the reason that causes the Outliers to depart from the correlation is their extremely depleted C{sup 6+}/C{sup 5+} ratio which is decreased by 80% compared to the normal slow wind. We discuss the implication of the Outlier solar wind for the solar wind acceleration mechanism.« less

Low-density laboratory spectra near the He ii λ304 line

DOE PAGES

Träbert, Elmar; Beiersdorfer, Peter; Brickhouse, Nancy S.; ...

2016-02-02

Aims. Our aim is to interpret the EUV spectra of the solar corona, one hopes for laboratory data of specific chemical elements obtained under coronal conditions. Methods. EUV spectra of He, C, N, O, F, Ne, S, Ar, Fe, and Ni in a 40 Å wide wavelength interval near λ304 were excited in an electron beam ion trap. Results. We observe some two hundred lines about half of which are not yet identified and included in spectral models. Conclusions. Lastly, our data provide a check on the atomic data bases underlying the spectral models that are used to interpret solarmore » corona data. However, a multitude of mostly weak additional lines taken together represent a flux that is comparable to that of various primary lines.« less

Thermodynamic effects of laser irradiation of implants placed in bone: an in vitro study.

PubMed

Leja, Chris; Geminiani, Alessandro; Caton, Jack; Romanos, Georgios E

2013-11-01

Lasers have been proposed for various applications involving dental implants, including uncovering implants and treating peri-implantitis. However, the effect of laser irradiation on the implant surface temperature is only partially known. The aim of this pilot study was to determine the effect of irradiation with diode, carbon dioxide, and Er:YAG lasers on the surface temperature of dental implants placed in bone, in vitro. For this study, one dental implant was placed in a bovine rib. A trephine bur was used to create a circumferential defect to simulate peri-implantitis, and thermocouples were placed at the coronal and apical aspect of the implant. The implant was irradiated for 60 s using four different lasers independently and change in temperature as well as time to reach a 10 °C increase in temperature were recorded. There was wide variability in results among the lasers and settings. Time for a 10 °C increase ranged from 0.9 to over 60 s for the coronal thermocouple and from 18 to over 60 s for the apical thermocouple. Maximum temperature ranged from 5.9 to 70.9 °C coronally and from 1.4 to 23.4 °C apically. During laser irradiation of dental implants, a surface temperature increase beyond the "critical threshold" of 10 °C can be reached after only 18 s.

Study of extreme-ultraviolet emission and properties of a coronal streamer from PROBA2/SWAP, HINODE/EIS and Mauna Loa Mk4 observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goryaev, F.; Slemzin, V.; Vainshtein, L.

2014-02-01

Wide-field extreme-ultraviolet (EUV) telescopes imaging in spectral bands sensitive to 1 MK plasma on the Sun often observe extended, ray-like coronal structures stretching radially from active regions to distances of 1.5-2 R {sub ☉}, which represent the EUV counterparts of white-light streamers. To explain this phenomenon, we investigated the properties of a streamer observed on 2010 October 20 and 21, by the PROBA2/SWAP EUV telescope together with the Hinode/EIS (HOP 165) and the Mauna Loa Mk4 white-light coronagraph. In the SWAP 174 Å band comprising the Fe IX-Fe XI lines, the streamer was detected to a distance of 2 Rmore » {sub ☉}. We assume that the EUV emission is dominated by collisional excitation and resonant scattering of monochromatic radiation coming from the underlying corona. Below 1.2 R {sub ☉}, the plasma density and temperature were derived from the Hinode/EIS data by a line-ratio method. Plasma conditions in the streamer and in the background corona above 1.2 R {sub ☉} from the disk center were determined by forward-modeling the emission that best fit the observational data in both EUV and white light. It was found that the plasma in the streamer above 1.2 R {sub ☉} is nearly isothermal, with a temperature of T = 1.43 ± 0.08 MK. The hydrostatic scale-height temperature determined from the evaluated density distribution was significantly higher (1.72 ± 0.08 MK), which suggests the existence of outward plasma flow along the streamer. We conclude that, inside the streamer, collisional excitation provided more than 90% of the observed EUV emission, whereas, in the background corona, the contribution of resonance scattering became comparable with that of collisions at R ≳ 2 R {sub ☉}.« less

Shock Acceleration of Solar Energetic Protons: The First 10 Minutes

NASA Technical Reports Server (NTRS)

Ng, Chee K.; Reames, Donald V.

2008-01-01

Proton acceleration at a parallel coronal shock is modeled with self-consistent Alfven wave excitation and shock transmission. 18 - 50 keV seed protons at 0.1% of plasma proton density are accelerated in 10 minutes to a power-law intensity spectrum rolling over at 300 MeV by a 2500km s-1 shock traveling outward from 3.5 solar radius, for typical coronal conditions and low ambient wave intensities. Interaction of high-energy protons of large pitch-angles with Alfven waves amplified by low-energy protons of small pitch angles is key to rapid acceleration. Shock acceleration is not significantly retarded by sunward streaming protons interacting with downstream waves. There is no significant second-order Fermi acceleration.

Creation of current filaments in the solar corona

NASA Technical Reports Server (NTRS)

Mikic, Z.; Schnack, D. D.; Van Hoven, G.

1989-01-01

It has been suggested that the solar corona is heated by the dissipation of electric currents. The low value of the resistivity requires the magnetic field to have structure at very small length scales if this mechanism is to work. In this paper it is demonstrated that the coronal magnetic field acquires small-scale structure through the braiding produced by smooth, randomly phased, photospheric flows. The current density develops a filamentary structure and grows exponentially in time. Nonlinear processes in the ideal magnetohydrodynamic equations produce a cascade effect, in which the structure introduced by the flow at large length scales is transferred to smaller scales. If this process continues down to the resistive dissipation length scale, it would provide an effective mechanism for coronal heating.

A coronal hole and its identification as the source of a high velocity solar wind stream

NASA Technical Reports Server (NTRS)

Krieger, A. S.; Timothy, A. F.; Roelof, E. C.

1973-01-01

X-ray images of the solar corona showed a magnetically open structure in the low corona which extended from N20W20 to the south pole. Analysis of the measured X-ray intensities shows the density scale heights within the structure to be typically a factor of two less than that in the surrounding large scale magnetically closed regions. The structure is identified as a coronal hole. Wind measurements for the appropriate period were traced back to the sun by the method of instantaneous ideal spirals. A striking agreement was found between the Carrington longitude of the solar source of a recurrent high velocity solar wind stream and the position of the hole.

Investigation of coronal holes in the radio and far-ultraviolet ranges

NASA Technical Reports Server (NTRS)

Sheridan, K. V.; Smerd, S. F.

1977-01-01

Results of coronal-hole observations carried out in the far-UV with a spectro-heliometer aboard Skylab are compared with corresponding results of ground-based radioheliograph measurements performed at frequencies of 80 and 160 MHz. It is found that the electron density derived from the far-UV observations for the transition region and lower corona is nearly three times greater than the value computed on the basis of the radio data. Unsuccessful attempts are made to eliminate this discrepancy by recalibrating the radio data and by recalculating the ionization equilibrium. A substantial local enhancement of the heavy-element abundance in certain parts of the transition region and inner chromosphere is considered as a possible cause of the discrepancy.

How Interplanetary Scintillation Data Can Improve Modeling of Coronal Mass Ejection Propagation

NASA Astrophysics Data System (ADS)

Taktakishvili, A.; Mays, M. L.; Manoharan, P. K.; Rastaetter, L.; Kuznetsova, M. M.

2017-12-01

Coronal mass ejections (CMEs) can have a significant impact on the Earth's magnetosphere-ionosphere system and cause widespread anomalies for satellites from geosynchronous to low-Earth orbit and produce effects such as geomagnetically induced currents. At the NASA/GSFC Community Coordinated Modeling Center we have been using ensemble modeling of CMEs since 2012. In this presnetation we demonstrate that using of interplanetary scintillation (IPS) observations from the Ooty Radio Telescope facility in India can help to track CME propagaion and improve ensemble forecasting of CMEs. The observations of the solar wind density and velocity using IPS from hundreds of distant sources in ensemble modeling of CMEs can be a game-changing improvement of the current state of the art in CME forecasting.

Partial analysis of the flare-prominence of 30 April 1974

NASA Technical Reports Server (NTRS)

Wu, S. T.; Dryer, M.; Mcintosh, P. S.; Reichmann, E.

1975-01-01

A portion of an east limb flare-prominence observed in H-alpha light is analyzed. Following rapid achievement of a maximum mass-ejection velocity of about 375 km/s, the ascending prominence reached a height of at least 200,000 km. A one-dimensional time-dependent hydrodynamic theory is used to compute the total mass and energy ejected during this part of the event. Theoretical aspects of the coronal response are discussed. It is concluded that a moderate temperature and density pulse (factors of ten and two, respectively) for a duration of only 3 min is sufficient for an acceptable simulation of the H-alpha observations and the likely coronal response to the ascending prominence and flare-related ejections.

New Evidence that Magnetoconvection Drives Solar–Stellar Coronal Heating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tiwari, Sanjiv K.; Panesar, Navdeep K.; Moore, Ronald L.

2017-07-10

How magnetic energy is injected and released in the solar corona, keeping it heated to several million degrees, remains elusive. Coronal heating generally increases with increasing magnetic field strength. From a comparison of a nonlinear force-free model of the three-dimensional active region coronal field to observed extreme-ultraviolet loops, we find that (1) umbra-to-umbra coronal loops, despite being rooted in the strongest magnetic flux, are invisible, and (2) the brightest loops have one foot in an umbra or penumbra and the other foot in another sunspot’s penumbra or in unipolar or mixed-polarity plage. The invisibility of umbra-to-umbra loops is new evidencemore » that magnetoconvection drives solar-stellar coronal heating: evidently, the strong umbral field at both ends quenches the magnetoconvection and hence the heating. Broadly, our results indicate that depending on the field strength in both feet, the photospheric feet of a coronal loop on any convective star can either engender or quench coronal heating in the loop’s body.« less

Type II solar radio burst band-splitting: Measure of coronal magnetic field strength

NASA Astrophysics Data System (ADS)

Mahrous, Ayman; Alielden, Khaled; Vršnak, Bojan; Youssef, Mohamed

2018-07-01

Studies of the relationship between solar radio bursts and CMEs are essential for understanding of the nature of type II bursts. In this study, we examine the type II solar radio burst recorded on 16 March 2016 by the Learmonth radio spectrograph and compare its characteristics with the kinematics of the associated CMEs observed by STEREO and SOHO spacecraft. The burst showed a well-defined band-split, which was used to estimate the magnetic field strength in the solar corona. The magnetic field decreases from ≈ 4 G at R ≈ 2.6 R⊙ to 0.62 G at R ≈ 3.77 R⊙ depending on the coronal electron density model employed. We found that two CMEs occurred successively in a 4-h interval. During this interval, a type II radio burst occurred, lasting for about 10 min. Tracking of the shock that produced type II burst and comparison with the CMEs heights as observed by STEREO and SOHO spacecraft help us to deduce the driver of the shock. According to the analysis, the type II burst occurrence was associated with the interaction of the shock driven by the second CME with a streamer located south of the first CME, since that the type II band-split significantly increased during the shock-streamer interaction. Our results show that the analysis of the type II burst band-split supplemented by the coronagraphic observations of the corona is an important tool for the understanding of the coronal eruptive processes.

THE INSTABILITY AND NON-EXISTENCE OF MULTI-STRANDED LOOPS WHEN DRIVEN BY TRANSVERSE WAVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magyar, N.; Van Doorsselaere, T., E-mail: norbert.magyar@wis.kuleuven.be

2016-06-01

In recent years, omni-present transverse waves have been observed in all layers of the solar atmosphere. Coronal loops are often modeled as a collection of individual strands in order to explain their thermal behavior and appearance. We perform three-dimensional (3D) ideal magnetohydrodynamics simulations to study the effect of a continuous small amplitude transverse footpoint driving on the internal structure of a coronal loop composed of strands. The output is also converted into synthetic images, corresponding to the AIA 171 and 193 Å passbands, using FoMo. We show that the multi-stranded loop ceases to exist in the traditional sense of themore » word, because the plasma is efficiently mixed perpendicularly to the magnetic field, with the Kelvin–Helmholtz instability acting as the main mechanism. The final product of our simulation is a mixed loop with density structures on a large range of scales, resembling a power-law. Thus, multi-stranded loops are unstable to driving by transverse waves, and this raises strong doubts on the usability and applicability of coronal loop models consisting of independent strands.« less

Classification of probability densities on the basis of Pearson?s curves with application to coronal heating simulations

NASA Astrophysics Data System (ADS)

Podladchikova, O.; Lefebvre, B.; Krasnoselskikh, V.; Podladchikov, V.

An important task for the problem of coronal heating is to produce reliable evaluation of the statistical properties of energy release and eruptive events such as micro-and nanoflares in the solar corona. Different types of distributions for the peak flux, peak count rate measurements, pixel intensities, total energy flux or emission measures increases or waiting times have appeared in the literature. This raises the question of a precise evaluation and classification of such distributions. For this purpose, we use the method proposed by K. Pearson at the beginning of the last century, based on the relationship between the first 4 moments of the distribution. Pearson's technique encompasses and classifies a broad range of distributions, including some of those which have appeared in the literature about coronal heating. This technique is successfully applied to simulated data from the model of Krasnoselskikh et al. (2002). It allows to provide successful fits to the empirical distributions of the dissipated energy, and to classify them as a function of model parameters such as dissipation mechanisms and threshold.

Hard X-ray emission from the solar corona

NASA Astrophysics Data System (ADS)

Krucker, S.; Battaglia, M.; Cargill, P. J.; Fletcher, L.; Hudson, H. S.; MacKinnon, A. L.; Masuda, S.; Sui, L.; Tomczak, M.; Veronig, A. L.; Vlahos, L.; White, S. M.

2008-10-01

This review surveys hard X-ray emissions of non-thermal electrons in the solar corona. These electrons originate in flares and flare-related processes. Hard X-ray emission is the most direct diagnostic of electron presence in the corona, and such observations provide quantitative determinations of the total energy in the non-thermal electrons. The most intense flare emissions are generally observed from the chromosphere at footpoints of magnetic loops. Over the years, however, many observations of hard X-ray and even γ-ray emission directly from the corona have also been reported. These coronal sources are of particular interest as they occur closest to where the electron acceleration is thought to occur. Prior to the actual direct imaging observations, disk occultation was usually required to study coronal sources, resulting in limited physical information. Now RHESSI has given us a systematic view of coronal sources that combines high spatial and spectral resolution with broad energy coverage and high sensitivity. Despite the low density and hence low bremsstrahlung efficiency of the corona, we now detect coronal hard X-ray emissions from sources in all phases of solar flares. Because the physical conditions in such sources may differ substantially from those of the usual “footpoint” emission regions, we take the opportunity to revisit the physics of hard X-radiation and relevant theories of particle acceleration.

Solar Coronal Lines in the Visible and Infrared: A Rough Guide

NASA Astrophysics Data System (ADS)

Del Zanna, Giulio; DeLuca, Edward E.

2018-01-01

We review the coronal visible and infrared lines, collecting previous observations and comparing, whenever available, observed radiances to those predicted by various models: the quiet Sun (QS), a moderately active Sun, and an active region as observed near the limb, around 1.1 R ⊙. We also model the off-limb radiances for the QS case. We used the most up-to-date atomic data in CHIANTI version 8. The comparison is satisfactory, in that all of the strong visible lines now have a firm identification. We revise several previous identifications and suggest some new ones. We also list the large number of observed lines for which we do not currently have atomic data, and therefore still await firm identifications. We also show that a significant number of coronal lines should be observable in the near-infrared region of the spectrum by the upcoming Daniel K. Inouye Solar Telescope (DKIST) and the AIR-Spec instrument, which observed the corona during the 2017 August 21 solar eclipse. We also briefly discuss the many potential spectroscopic diagnostics available to the visible and infrared, with particular emphasis on measurements of electron densities and chemical abundances. We briefly point out some of the potential diagnostics that could be available with the future infrared instrumentation that is being built for DKIST and planned for the Coronal Solar Magnetism Observatory. Finally, we highlight the need for further improvements in the atomic data.

Disruption of Helmet Streamers by Current Emergence

NASA Technical Reports Server (NTRS)

Guo, W. P.; Wu, S. T.; Tandberg-Hanssen, E.

1996-01-01

We have investigated the dynamic response of a coronal helmet streamer to the emergence from below of a current with its magnetic field in a direction opposite to the overlying streamer field. Once the emerging current moves into the closed region of the streamer, a current sheet forms between the emerging field and the streamer field, because the preexisting field and the newly emerging field have opposite polarities. Thus magnetic reconnection will occur at the flanks of the emerged structure where the current density is maximum. If the emerging current is large enough, the energy contained in the current and the reconnection will promptly disrupt the streamer. If the emerging current is small, the streamer will experience a stage of slow evolution. In this stage, slow magnetic reconnection occurring at the flanks of the emerged structure leads to the degeneration of the emerged current to a neutral point. Above this point, a new magnetic bubble will form. The resulting configuration resembles an inverse-polarity prominence. Depending on the initial input energy of the current, the resulting structure will either remain in situ, forming a quasi-static structure, or move upward, forming a coronal transient similar to coronal jets. The numerical method used in this paper can be used to construct helmet streamers containing a detached magnetic structure in their closed field region. The quasi-static solution may serve as a preevent corona for studying coronal mass ejection initiation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morioka, A.; Misawa, H.; Obara, T.

Solar micro-type III radio bursts are elements of the so-called type III storms and are characterized by short-lived, continuous, and weak emissions. Their frequency of occurrence with respect to radiation power is quite different from that of ordinary type III bursts, suggesting that the generation process is not flare-related, but due to some recurrent acceleration processes around the active region. We examine the relationship of micro-type III radio bursts with coronal streamers. We also explore the propagation channel of bursts in the outer corona, the acceleration process, and the escape route of electron beams. It is observationally confirmed that micro-typemore » III bursts occur near the edge of coronal streamers. The magnetic field line of the escaping electron beams is tracked on the basis of the frequency drift rate of micro-type III bursts and the electron density distribution model. The results demonstrate that electron beams are trapped along closed dipolar field lines in the outer coronal region, which arise from the interface region between the active region and the coronal hole. A 22 year statistical study reveals that the apex altitude of the magnetic loop ranges from 15 to 50 R{sub S}. The distribution of the apex altitude has a sharp upper limit around 50 R{sub S} suggesting that an unknown but universal condition regulates the upper boundary of the streamer dipolar field.« less

Measuring Temperature-Dependent Propagating Disturbances in Coronal Fan Loops Using Multiple SDO-AIA Channels and Surfing Transform Technique

NASA Technical Reports Server (NTRS)

Uritskiy, Vadim M.; Davila, Joseph M.; Viall, Nicholeen M.; Ofman, Leon

2013-01-01

A set of co-aligned high resolution images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory (SDO) is used to investigate propagating disturbances (PDs) in warm fan loops at the periphery of a non-flaring active region NOAA AR 11082. To measure PD speeds at multiple coronal temperatures, a new data analysis methodology is proposed enabling quantitative description of sub visual coronal motions with low signal-to-noise ratios of the order of 0.1. The technique operates with a set of one-dimensional surfing signals extracted from position-timeplots of several AIA channels through a modified version of Radon transform. The signals are used to evaluate a two-dimensional power spectral density distribution in the frequency - velocity space which exhibits a resonance in the presence of quasi-periodic PDs. By applying this analysis to the same fan loop structures observed in several AIA channels, we found that the traveling velocity of PDs increases with the temperature of the coronal plasma following the square root dependence predicted for the slow mode magneto-acoustic wave which seems to be the dominating wave mode in the studied loop structures. This result extends recent observations by Kiddie et al. (2012) to a more general class of fan loop systems not associated with sunspots and demonstrating consistent slow mode activity in up to four AIA channels.

Signatures Of Coronal Heating Driven By Footpoint Shuffling: Closed and Open Structures.

NASA Astrophysics Data System (ADS)

Velli, M. C. M.; Rappazzo, A. F.; Dahlburg, R. B.; Einaudi, G.; Ugarte-Urra, I.

2017-12-01

We have previously described the characteristic state of the confined coronal magnetic field as a special case of magnetically dominated magnetohydrodynamic (MHD) turbulence, where the free energy in the transverse magnetic field is continuously cascaded to small scales, even though the overall kinetic energy is small. This coronal turbulence problem is defined by the photospheric boundary conditions: here we discuss recent numerical simulations of the fully compressible 3D MHD equations using the HYPERION code. Loops are forced at their footpoints by random photospheric motions, energizing the field to a state with continuous formation and dissipation of field-aligned current sheets: energy is deposited at small scales where heating occurs. Only a fraction of the coronal mass and volume gets heated at any time. Temperature and density are highly structured at scales that, in the solar corona, remain observationally unresolved: the plasma of simulated loops is multithermal, where highly dynamical hotter and cooler plasma strands are scattered throughout the loop at sub-observational scales. We will also compare Reduced MHD simulations with fully compressible simulations and photospheric forcings with different time-scales compared to the Alfv'en transit time. Finally, we will discuss the differences between the closed field and open field (solar wind) turbulence heating problem, leading to observational consequences that may be amenable to Parker Solar Probe and Solar Orbiter.

Polarization of Coronal Forbidden Lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hao; Qu, Zhongquan; Landi Degl’Innocenti, Egidio, E-mail: sayahoro@ynao.ac.cn

Since the magnetic field is responsible for most manifestations of solar activity, one of the most challenging problems in solar physics is the diagnostics of solar magnetic fields, particularly in the outer atmosphere. To this end, it is important to develop rigorous diagnostic tools to interpret polarimetric observations in suitable spectral lines. This paper is devoted to analyzing the diagnostic content of linear polarization imaging observations in coronal forbidden lines. Although this technique is restricted to off-limb observations, it represents a significant tool to diagnose the magnetic field structure in the solar corona, where the magnetic field is intrinsically weakmore » and still poorly known. We adopt the quantum theory of polarized line formation developed in the framework of the density matrix formalism, and synthesize images of the emergent linear polarization signal in coronal forbidden lines using potential-field source-surface magnetic field models. The influence of electronic collisions, active regions, and Thomson scattering on the linear polarization of coronal forbidden lines is also examined. It is found that active regions and Thomson scattering are capable of conspicuously influencing the orientation of the linear polarization. These effects have to be carefully taken into account to increase the accuracy of the field diagnostics. We also found that linear polarization observation in suitable lines can give valuable information on the long-term evolution of the magnetic field in the solar corona.« less

Coronal Heating and the Magnetic Flux Content of the Network

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Hathaway, D. H.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

Previously, from analysis of SOHO/EIT coronal images in combination with Kitt Peak magnetograms (Falconer et al 1998, ApJ, 501, 386-396), we found that the quiet corona is the sum of two components: the e-scale corona and the coronal network. The large-scale corona consists of all coronal-temperature (T approx. 10(exp 6) K) structures larger than supergranules (>approx.30,000 km). The coronal network (1) consists of all coronal-temperature structures smaller than supergranules, (2) is rooted in and loosely traces the photospheric magnetic network, (3) has its brightest features seated on polarity dividing fines (neutral lines) in the network magnetic flux, and (4) produces only about 5% of the total coronal emission in quiet regions. The heating of the coronal network is apparently magnetic in origin. Here, from analysis of EIT coronal images of quiet regions in combination with magnetograms of the same quiet regions from SOHO/MDI and from Kitt Peak, we examine the other 95% of the quiet corona and its relation to the underlying magnetic network. We find: (1) Dividing the large-scale corona into its bright and dim halves divides the area into bright "continents" and dark "oceans" having spans of 2-4 supergranules. (2) These patterns are also present in the photospheric magnetograms: the network is stronger under the bright half and weaker under the dim half. (3) The radiation from the large-scale corona increases roughly as the cube root of the magnetic flux content of the underlying magnetic network. In contrast, Fisher et A (1998, ApJ, 508, 985-998) found that the coronal radiation from an active region increases roughly linearly with the magnetic flux content of the active region. We assume, as is widely held, that nearly all of the large-scale corona is magnetically rooted in the network. Our results, together with the result of Fisher et al (1999), suggest that either the coronal heating in quiet regions has a large non-magnetic component, or, if the heating is predominantly produced via the magnetic field, the mechanism is significantly different than in active regions. This work is funded by NASA's Office of Space Science through the Solar Physics Supporting Research and Technology Program and the Sun-Earth Connection Guest Investigator Program.

A Universal Model for Solar Eruptions

NASA Astrophysics Data System (ADS)

Wyper, Peter; Antiochos, Spiro K.; DeVore, C. Richard

2017-08-01

We present a universal model for solar eruptions that encompasses coronal mass ejections (CMEs) at one end of the scale, to coronal jets at the other. The model is a natural extension of the Magnetic Breakout model for large-scale fast CMEs. Using high-resolution adaptive mesh MHD simulations conducted with the ARMS code, we show that so-called blowout or mini-filament coronal jets can be explained as one realisation of the breakout process. We also demonstrate the robustness of this “breakout-jet” model by studying three realisations in simulations with different ambient field inclinations. We conclude that magnetic breakout supports both large-scale fast CMEs and small-scale coronal jets, and by inference eruptions at scales in between. Thus, magnetic breakout provides a unified model for solar eruptions. P.F.W was supported in this work by an award of a RAS Fellowship and an appointment to the NASA Postdoctoral Program. C.R.D and S.K.A were supported by NASA’s LWS TR&T and H-SR programs.

SUNQUAKE GENERATION BY CORONAL MAGNETIC RESTRUCTURING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, A. J. B.; Mooney, M. K.; Leake, J. E.

2016-11-01

Sunquakes are the surface signatures of acoustic waves in the Sun’s interior that are produced by some but not all flares and coronal mass ejections (CMEs). This paper explores a mechanism for sunquake generation by the changes in magnetic field that occur during flares and CMEs, using MHD simulations with a semiempirical FAL-C atmosphere to demonstrate the generation of acoustic waves in the interior in response to changing magnetic tilt in the corona. We find that Alfvén–sound resonance combined with the ponderomotive force produces acoustic waves in the interior with sufficient energy to match sunquake observations when the magnetic fieldmore » angle changes of the order of 10° in a region where the coronal field strength is a few hundred gauss or more. The most energetic sunquakes are produced when the coronal field is strong, while the variation of magnetic field strength with height and the timescale of the change in tilt are of secondary importance.« less

The innermost corona observed at the 1973 June 30 eclipse

NASA Astrophysics Data System (ADS)

Hanaoka, Yoichiro; Kanno, Mitsuo; Kurokawa, Hiroki; Tsubaki, Tokio

1986-07-01

Slitless flash spectrograms in heights below 8000 km above the solar limb were obtained by the University of Kyoto expedition at Atar, Mauritania. The integrated intensities of Fe XIV, Fe X, Fe XI, and the continuum are measured as a function of height above the solar limb at 11 points around the third contact point. It is found that a significant amount of the emission in Fe X originates in chromospheric levels well below 8000 km. This implies that the interspicular region of the chromosphere is occupied by coronal material. The average values of the electron temperature (0.9-1.1 million K) and the electron density in the interspicular region are derived from the Fe X and the Fe XI intensities (0.9-1 billion/cu cm) on the assumption of spherical symmetry. The intensity variations of the coronal lines and the continuum with position angle are also studied. Strong correlations between Fe XIV and the continuum and between Fe X and Fe XI are found. The Fe X intensities indicate a density fluctuation in the innermost corona by at least a factor of two.

A Coronal Hole Jet Observed with Hinode and the Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Young, Peter H.; Muglach, Karin

2014-01-01

A small blowout jet was observed at the boundary of the south coronal hole on 2011 February 8 at around 21:00 UT. Images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory (SDO) revealed an expanding loop rising from one footpoint of a compact, bipolar bright point. Magnetograms from the Helioseismic Magnetic Imager (HMI) on board SDO showed that the jet was triggered by the cancelation of a parasitic positive polarity feature near the negative pole of the bright point. The jet emission was present for 25 mins and it extended 30 Mm from the bright point. Spectra from the EUV Imaging Spectrometer on board Hinode yielded a temperature and density of 1.6 MK and 0.9-1.7 × 10( exp 8) cu cm for the ejected plasma. Line-of-sight velocities reached up to 250 km/s. The density of the bright point was 7.6 × 10(exp 8) cu cm, and the peak of the bright point's emission measure occurred at 1.3 MK, with no plasma above 3 MK.

3-Dimensional shear wave elastography of breast lesions

PubMed Central

Chen, Ya-ling; Chang, Cai; Zeng, Wei; Wang, Fen; Chen, Jia-jian; Qu, Ning

2016-01-01

Abstract Color patterns of 3-dimensional (3D) shear wave elastography (SWE) is a promising method in differentiating tumoral nodules recently. This study was to evaluate the diagnostic accuracy of color patterns of 3D SWE in breast lesions, with special emphasis on coronal planes. A total of 198 consecutive women with 198 breast lesions (125 malignant and 73 benign) were included, who underwent conventional ultrasound (US), 3D B-mode, and 3D SWE before surgical excision. SWE color patterns of Views A (transverse), T (sagittal), and C (coronal) were determined. Sensitivity, specificity, and the area under the receiver operating characteristic curve (AUC) were calculated. Distribution of SWE color patterns was significantly different between malignant and benign lesions (P = 0.001). In malignant lesions, “Stiff Rim” was significantly more frequent in View C (crater sign, 60.8%) than in View A (51.2%, P = 0.013) and View T (54.1%, P = 0.035). AUC for combination of “Crater Sign” and conventional US was significantly higher than View A (0.929 vs 0.902, P = 0.004) and View T (0.929 vs 0.907, P = 0.009), and specificity significantly increased (90.4% vs 78.1%, P = 0.013) without significant change in sensitivity (85.6% vs 88.0%, P = 0.664) as compared with conventional US. In conclusion, combination of conventional US with 3D SWE color patterns significantly increased diagnostic accuracy, with “Crater Sign” in coronal plane of the highest value. PMID:27684820

Deposing the Cool Corona of KPD 0005+5106

NASA Astrophysics Data System (ADS)

Drake, Jeremy J.; Werner, Klaus

2005-06-01

The ROSAT PSPC pulse-height spectrum of the peculiar He-rich hot white dwarf KPD 0005+5106 provided a great surprise when first analyzed by Fleming, Werner, & Barstow. It defied the best non-LTE modeling attempts in terms of photospheric emission from He-dominated atmospheres including C, N, and O and was instead interpreted as the first evidence for a coronal plasma around a white dwarf. We show here that a recent high-resolution Chandra LETGS spectrum has more structure than expected from a thermal bremsstrahlung continuum and lacks the narrow lines of H-like and He-like C expected from a coronal plasma. Moreover, a coronal model requires a total luminosity more than 2 orders of magnitude larger than that of the star itself. Instead, the observed 20-80 Å flux is consistent with photospheric models containing trace amounts of heavier elements such as Fe. The soft X-ray flux is highly sensitive to the adopted metal abundance and provides a metal abundance diagnostic. The weak X-ray emission at 1 keV announced by O'Dwyer and coworkers instead cannot arise from the photosphere and requires alternative explanations. We echo earlier speculation that such emission arises in a shocked wind. Despite the presence of UV-optical O VIII lines from transitions between levels n=7 and 10, no X-ray O VIII Lyα flux is detected. We show that O VIII Lyman photons can be trapped by resonant scattering within the emitting plasma and destroyed by photoelectric absorption.

Solar and stellar coronal plasmas

NASA Technical Reports Server (NTRS)

Golub, L.

1985-01-01

Progress made in describing and interpreting coronal plasma processes and the relationship between the solar corona and its stellar counterparts is reported. Topics covered include: stellar X-ray emission, HEAO 2 X-ray survey of the Pleiades, closed coronal structures, X-ray survey of main-sequence stars with shallow convection zones, implications of the 1400 MHz flare emission, and magnetic field stochasticity.

Periapical inflammation subsequent to coronal inoculation of dog teeth root filled with resilon/epiphany in 1 or 2 treatment sessions with chlorhexidine medication.

PubMed

Santos, João M; Palma, Paulo J; Ramos, João C; Cabrita, António S; Friedman, Shimon

2014-06-01

Therapeutic methods that inhibit microbial ingress into filled root canals are desirable. This in vivo study assessed the inhibition of periapical inflammation subsequent to coronal inoculation in canals medicated with 2% chlorhexidine gel and filled with Resilon/Epiphany (Pentron Clinical Technologies, Wallingford, CT). Six Beagle dogs each had 10 two-rooted premolars treated. In group 1 (n = 36 roots), 1 root/tooth had the canal conditioned with Primer Epiphany, filled with Epiphany sealer and Resilon core in 1 session, and coronally sealed with PhotacFil. In group 2 (n = 36 roots), the second root/tooth had the canal medicated with 2% chlorhexidine gel for 1 week and then filled and coronally sealed as in group 1. After 3 weeks, canals were exposed to the oral environment for 7 days, inoculated with isologous plaque, and coronally sealed. Negative controls treated as groups 1 and 2 remained sealed. Positive controls had canals unfilled and exposed. Seven months after inoculation, dogs were euthanized; jaw blocks processed for histologic examination; and periapical inflammation (PI) recorded as none, mild, or severe. In groups 1 and 2, severe PI occurred in 5 of 65 roots (8%) and mild PI in 18 of 65 roots (28%) with a significantly higher (P = .031) PI incidence in group 2 than in group 1. Negative controls had only mild PI in 9 of 29 roots (31%). Roots medicated with 2% chlorhexidine gel had mild PI significantly more (P = .009) than roots filled in 1 session (more than 2-fold). Intracanal medication with 2% chlorhexidine gel and root filling with Resilon/Epiphany did not effectively inhibit apical periodontitis subsequent to coronal inoculation. Copyright © 2014 American Association of Endodontists. All rights reserved.

Identification of Low Coronal Sources of “Stealth” Coronal Mass Ejections Using New Image Processing Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alzate, Nathalia; Morgan, Huw, E-mail: naa19@aber.ac.uk

Coronal mass ejections (CMEs) are generally associated with low coronal signatures (LCSs), such as flares, filament eruptions, extreme ultraviolet (EUV) waves, or jets. A number of recent studies have reported the existence of stealth CMEs as events without LCSs, possibly due to observational limitations. Our study focuses on a set of 40 stealth CMEs identified from a study by D’Huys et al. New image processing techniques are applied to high-cadence, multi-instrument sets of images spanning the onset and propagation time of each of these CMEs to search for possible LCSs. Twenty-three of these events are identified as small, low-mass, unstructuredmore » blobs or puffs, often occurring in the aftermath of a large CME, but associated with LCSs such as small flares, jets, or filament eruptions. Of the larger CMEs, seven are associated with jets and eight with filament eruptions. Several of these filament eruptions are different from the standard model of an erupting filament/flux tube in that they are eruptions of large, faint flux tubes that seem to exist at large heights for a long time prior to their slow eruption. For two of these events, we see an eruption in Large Angle Spectrometric Coronagraph C2 images and the consequent changes at the bottom edge of the eruption in EUV images. All 40 events in our study are associated with some form of LCS. We conclude that stealth CMEs arise from observational and processing limitations.« less

Normal Development and Measurements of the Occipital Condyle-C1 Interval in Children and Young Adults.

PubMed

Smith, P; Linscott, L L; Vadivelu, S; Zhang, B; Leach, J L

2016-05-01

Widening of the occipital condyle-C1 interval is the most specific and sensitive means of detecting atlanto-occipital dislocation. Recent studies attempting to define normal measurements of the condyle-C1 interval in children have varied substantially. This study was performed to test the null hypothesis that condyle-C1 interval morphology and joint measurements do not change as a function of age. Imaging review of subjects undergoing CT of the upper cervical spine for reasons unrelated to trauma or developmental abnormality was performed. Four equidistant measurements were obtained for each bilateral condyle-C1 interval on sagittal and coronal images. The cohort was divided into 7 age groups to calculate the mean, SD, and 95% CIs for the average condyle-C1 interval in both planes. The prevalence of a medial occipital condyle notch was calculated. Two hundred forty-eight joints were measured in 124 subjects with an age range of 2 days to 22 years. The condyle-C1 interval varies substantially by age. Average coronal measurements are larger and more variable than sagittal measurements. The medial occipital condyle notch is most prevalent from 1 to 12 years and is uncommon in older adolescents and young adults. The condyle-C1 interval increases during the first several years of life, is largest in the 2- to 4-year age range, and then decreases through late childhood and adolescence. A single threshold value to detect atlanto-occipital dissociation may not be sensitive and specific for all age groups. Application of this normative data to documented cases of atlanto-occipital injury is needed to determine clinical utility. © 2016 by American Journal of Neuroradiology.

Coronal leakage in endodontically treated teeth restored with posts and complete crowns using different luting agent combinations.

PubMed

Nissan, Joseph; Rosner, Ofir; Gross, Ora; Pilo, Raphael; Lin, Shaul

2011-04-01

To evaluate the influence of different cement combinations on coronal microleakage in restored endodontically treated teeth using dye penetration. Human, noncarious single-rooted extracted premolars (n = 60) were divided into four experimental groups (each n = 15). After endodontic treatment, different combinations of cements were used to lute prefabricated posts and complete crown restorations: zinc phosphate cement applied on posts and cast crowns (Z) or on zinc phosphate cement posts and resin cement applied on cast crowns (ZR); resin cement applied on posts and zinc phosphate cement applied on cast crowns (RZ); and resin cement applied on posts and cast crowns (R). After artificial aging through thermal cycling (5°C to 55°C) for 2,000 cycles at 38 seconds for each cycle and 15 seconds of dwell time, specimens were immersed for 72 hours in basic fuchsin at 37°C. A buccolingual section was made through the vertical axis of specimens. A Toolmaker's microscope (Mitutoyo) was used to measure (um) dye penetration. The Kruskal-Wallis nonparametric test was used to determine intergroup difference. A nonparametric Mann-Whitney test compared each group regarding its maximal linear penetration depths on the mesial and distal aspects of each specimen (a = 0.05). Dye staining was evident to some degree in all specimens. Among groups Z, ZR, and RZ, no significant difference was shown in dye-penetration depths (mean penetration scores 1,518 to 1,807 um). However, dyepenetration depth was significantly lower in group R compared to the other groups (mean penetration score 1,073 um) (P < .05). Under study conditions, the cement combination offering the best coronal sealing was the one using only resin cement for both posts and crown restorations.

Returning Coronal Hole

NASA Image and Video Library

2017-02-06

A substantial coronal hole rotated across the face of the sun this past week and is again streaming solar wind towards Earth (Jan. 30 - Feb. 2, 2017). This same coronal hole was facing Earth about a month ago and has rotated into a similar position again. Coronal holes are areas of open magnetic field from which solar wind particles stream into space. In this wavelength of extreme ultraviolet light it appears as a dark area near the center and lower portion of the sun. Movies are available at http://photojournal.jpl.nasa.gov/catalog/PIA11177

Coronal Hole Coming Around

NASA Image and Video Library

2016-12-06

A substantial coronal hole began to rotate into view over the past few days (Dec. 1-2, 2016). Coronal holes are magnetically open areas of the sun's magnetic field structure that spew streams of high speed solar wind into space. In about a week or so that coronal hole might send streams of particles in the direction of Earth. Often times these streams can interact with Earth's magnetosphere and generate aurora. The images were taken in a wavelength of extreme ultraviolet light. Movies are available at http://photojournal.jpl.nasa.gov/catalog/PIA21208

First Use of Synoptic Vector Magnetograms for Global Nonlinear, Force-Free Coronal Magnetic Field Models

NASA Technical Reports Server (NTRS)

Tadesse, T.; Wiegelmann, T.; Gosain, S.; MacNeice, P.; Pevtsov, A. A.

2014-01-01

Context. The magnetic field permeating the solar atmosphere is generally thought to provide the energy for much of the activity seen in the solar corona, such as flares, coronal mass ejections (CMEs), etc. To overcome the unavailability of coronal magnetic field measurements, photospheric magnetic field vector data can be used to reconstruct the coronal field. Currently, there are several modelling techniques being used to calculate three-dimensional field lines into the solar atmosphere. Aims. For the first time, synoptic maps of a photospheric-vector magnetic field synthesized from the vector spectromagnetograph (VSM) on Synoptic Optical Long-term Investigations of the Sun (SOLIS) are used to model the coronal magnetic field and estimate free magnetic energy in the global scale. The free energy (i.e., the energy in excess of the potential field energy) is one of the main indicators used in space weather forecasts to predict the eruptivity of active regions. Methods. We solve the nonlinear force-free field equations using an optimization principle in spherical geometry. The resulting threedimensional magnetic fields are used to estimate the magnetic free energy content E(sub free) = E(sub nlfff) - E(sub pot), which is the difference of the magnetic energies between the nonpotential field and the potential field in the global solar corona. For comparison, we overlay the extrapolated magnetic field lines with the extreme ultraviolet (EUV) observations by the atmospheric imaging assembly (AIA) on board the Solar Dynamics Observatory (SDO). Results. For a single Carrington rotation 2121, we find that the global nonlinear force-free field (NLFFF) magnetic energy density is 10.3% higher than the potential one. Most of this free energy is located in active regions.

Key aspects of coronal heating

PubMed Central

Klimchuk, James A.

2015-01-01

We highlight 10 key aspects of coronal heating that must be understood before we can consider the problem to be solved. (1) All coronal heating is impulsive. (2) The details of coronal heating matter. (3) The corona is filled with elemental magnetic stands. (4) The corona is densely populated with current sheets. (5) The strands must reconnect to prevent an infinite build-up of stress. (6) Nanoflares repeat with different frequencies. (7) What is the characteristic magnitude of energy release? (8) What causes the collective behaviour responsible for loops? (9) What are the onset conditions for energy release? (10) Chromospheric nanoflares are not a primary source of coronal plasma. Significant progress in solving the coronal heating problem will require coordination of approaches: observational studies, field-aligned hydrodynamic simulations, large-scale and localized three-dimensional magnetohydrodynamic simulations, and possibly also kinetic simulations. There is a unique value to each of these approaches, and the community must strive to coordinate better. PMID:25897094

Structure and sources of solar wind in the growing phase of 24th solar cycle

NASA Astrophysics Data System (ADS)

Slemzin, Vladimir; Goryaev, Farid; Shugay, Julia; Rodkin, Denis; Veselovsky, Igor

2015-04-01

We present analysis of the solar wind (SW) structure and its association with coronal sources during the minimum and rising phase of 24th solar cycle (2009-2011). The coronal sources prominent in this period - coronal holes, small areas of open magnetic fields near active regions and transient sources associated with small-scale solar activity have been investigated using EUV solar images and soft X-ray fluxes obtained by the CORONAS-Photon/TESIS/Sphinx, PROBA2/SWAP, Hinode/EIS and AIA/SDO instruments as well as the magnetograms obtained by HMI/SDO. It was found that at solar minimum (2009) velocity and magnetic field strength of high speed wind (HSW) and transient SW from small-scale flares did not differ significantly from those of the background slow speed wind (SSW). The major difference between parameters of different SW components was seen in the ion composition represented by the C6/C5, O7/O6, Fe/O ratios and the mean charge of Fe ions. With growing solar activity, the speed of HSW increased due to transformation of its sources - small-size low-latitude coronal holes into equatorial extensions of large polar holes. At that period, the ion composition of transient SW changed from low-temperature to high-temperature values, which was caused by variation of the source conditions and change of the recombination/ionization rates during passage of the plasma flow through the low corona. However, we conclude that criteria of separation of the SW components based on the ion ratios established earlier by Zhao&Fisk (2009) for higher solar activity are not applicable to the extremely weak beginning of 24th cycle. The research leading to these results has received funding from the European Commission's Seventh Framework Programme (FP7/2007-2013) under the grant agreement eHeroes (project n° 284461, www.eheroes.eu).

Interplanetary Magnetic Field and Plasma Values Related to Hildcaas Events

NASA Astrophysics Data System (ADS)

Prestes, A.; Serra, S. L.; Vieira, L. A.

2013-05-01

In this work we investigate the interplanetary conditions during the occurrence of 150 HILDCAAs/QUASI-HILDCAAs events occurred between 1998 and 2007. These events were chosen by following strictly the selection criteria for this kind of phenomena and with some criteria flexible. Among the criteria used to characterize events HILDCAAs, the criterion that considers "the AE values never dropped below 200 nT for more than 2 h at a time" was more restrictive, thus only this was modified by changing from 2 to 4 hours the period in which the AE value can't be below 200 nT. In the interplanetary medium, HILDCAAs are associated with high speed solar wind streams, which are frequently embedded with alfvénic fluctuations. At the Sun, these high speed streams are originated in coronal holes. The distribution of events HILDCAAs/quasi-HILDCAAs along the solar cycle shows a pattern of double peak, a less intense around the maximum of the sunspot cycle and other intense in the descending phase, similar to the distribution of low-latitude coronal holes. For each one of the selected events we have found the most probable value of interplanetary magnetic field and plasma. The average values of AE, AU, AL and Dst indices, the density and temperature of the solar wind protons, the solar wind speed, the Bz component of the IMF, the IMF intensity, dynamic pressure and factor beta, among all the 150 events HILDCAAs/quasi-HILDCAAs, were: AE (344.5 ± 65.0 nT), AU (131.0 ± 33.0 nT), AL (-213.7 ± 51.2 nT), Dst (-25.8 ± 12.2 nT), Density (5,0 ± 1,8 cm-3), Temperature (151269.5 ± 48907.7 K), |V| (538.2 ± 83.3 km/s) Bz (-0.71 ± 1.02 nT), |B| (6.7 ± 1.4 nT) pressure (2.6 ± 0.7 nPa) and Beta (0.66 ± 0.27).

The radial gradients and collisional properties of solar wind electrons

NASA Technical Reports Server (NTRS)

Gilvie, K. W.; Scudder, J. D.

1977-01-01

The plasma instrument on Mariner 10 carried out measurements of electron density and temperature in the interplanetary medium between heliocentric distances of 0.85 and 0.45 AU. Due to the stable coronal configuration and low solar activity during the period of observation, the radial variations of these quantities could be obtained. The power-law exponent of the core temperature was measured to be -0.3 + or - 0.04, and the halo temperature was found to be almost independent of heliocentric distance. The exponent of the power law for the density variation was 2.5 + or - 0.2 and the extrapolated value at 1 AU was consistent with measured values during the same period. Calculations of the core electron self-collision time, and the core-halo equipartition time were made as a function of radial distance. These measurements indicate a macroscale picture of a Coulomb-collisional core and a collisionless isothermal halo. Extrapolating back to the sun, core and halo temperatures become equal at a radial distance of approx. 2-15 radii.

Corongraphic Observations and Analyses of The Ultraviolet Solar Corona

NASA Technical Reports Server (NTRS)

Kohl, John L.

2000-01-01

The activities supported under NASA Grant NAG5-613 included the following: 1) reduction and scientific analysis of data from three sounding rocket flights of the Rocket Ultraviolet Coronagraph Spectrometer, 2) development of ultraviolet spectroscopic diagnostic techniques to provide a detailed empirical description of the extended solar corona, 3) extensive upgrade of the rocket instrument to become the Ultraviolet Coronal Spectrometer (UVCS) for Spartan 201,4) instrument scientific calibration and characterization, 5) observation planning and mission support for a series of five Spartan 201 missions (fully successful except for STS 87 where the Spartan spacecraft was not successfully deployed and the instruments were not activated), and 6) reduction and scientific analysis of the UVCS/Spartan 201 observational data. The Ultraviolet Coronal Spectrometer for Spartan 201 was one unit of a joint payload and the other unit was a White Light Coronagraph (WLC) provided by the High Altitude Observatory and the Goddard Space Flight Center. The two instruments were used in concert to determine plasma parameters describing structures in the extended solar corona. They provided data that could be used individually or jointly in scientific analyses. The WLC provided electron column densities in high spatial resolution and high time resolution. UVCS/Spartan provided hydrogen velocity distributions, and line of sight hydrogen velocities. The hydrogen intensities from UVCS together with the electron densities from WLC were used to determine hydrogen outflow velocities. The UVCS also provided O VI intensities which were used to develop diagnostics for velocity distributions and outflow velocities of minor ions.

Super- and sub-critical regions in shocks driven by radio-loud and radio-quiet CMEs

PubMed Central

Bemporad, Alessandro; Mancuso, Salvatore

2012-01-01

White-light coronagraphic images of Coronal Mass Ejections (CMEs) observed by SOHO/LASCO C2 have been used to estimate the density jump along the whole front of two CME-driven shocks. The two events are different in that the first one was a “radio-loud” fast CME, while the second one was a “radio quiet” slow CME. From the compression ratios inferred along the shock fronts, we estimated the Alfvén Mach numbers for the general case of an oblique shock. It turns out that the “radio-loud” CME shock is initially super-critical around the shock center, while later on the whole shock becomes sub-critical. On the contrary, the shock associated with the “radio-quiet” CME is sub-critical at all times. This suggests that CME-driven shocks could be efficient particle accelerators at the shock nose only at the initiation phases of the event, if and when the shock is super-critical, while at later times they lose their energy and the capability to accelerate high energetic particles. PMID:25685431

Bright point study. [of solar corona

NASA Technical Reports Server (NTRS)

Tang, F.; Harvey, K.; Bruner, M.; Kent, B.; Antonucci, E.

1982-01-01

Transition region and coronal observations of bright points by instruments aboard the Solar Maximum Mission and high resolution photospheric magnetograph observations on September 11, 1980 are presented. A total of 31 bipolar ephemeral regions were found in the photosphere from birth in 9.3 hours of combined magnetograph observations from three observatories. Two of the three ephemeral regions present in the field of view of the Ultraviolet Spectrometer-Polarimeter were observed in the C IV 1548 line. The unobserved ephemeral region was determined to be the shortest-lived (2.5 hr) and lowest in magnetic flux density (13G) of the three regions. The Flat Crystal Spectrometer observed only low level signals in the O VIII 18.969 A line, which were not statistically significant to be positively identified with any of the 16 ephemeral regions detected in the photosphere. In addition, the data indicate that at any given time there lacked a one-to-one correspondence between observable bright points and photospheric ephemeral regions, while more ephemeral regions were observed than their counterparts in the transition region and the corona.

On the temperature and the interstellar nature of coronal gas observed by Copernicus

NASA Technical Reports Server (NTRS)

York, D. G.

1977-01-01

More detailed scans of ions expected in interstellar absorption at temperatures of 100,000 to 1 million K have been made with Copernicus in five stars: Alpha Vir, Beta Cen, Lambda Sco, Mu Col, and HD 28497. Preliminary data show that the absorption due to O VI is stationary compared with the velocities of stellar absorption in the spectrum of the spectroscopic binary Lambda Sco, thus demonstrating its nonstellar nature. Ionization temperatures interpreted using steady-state or time-dependent assumptions yield values of 280,000 to 700,000 K. There is some evidence that a range of temperatures consistent with this spread may in fact exist in Alpha Vir. For this limited sample of data, there is no clear evidence for a generic association of low-column-density H2 and the O VI absorption. It is concluded that the O VI absorption refers to regions with temperatures exceeding 250,000 K. The only UV diagnostic for the gas appears to be the O VI features, though C IV may be useful in some cases.

Pulp Calcification in Traumatized Primary Teeth - Classification, Clinical And Radiographic Aspects.

PubMed

Mello-Moura, Anna Carolina Volpi; Santos, Ana Maria Antunes; Bonini, Gabriela Azevedo Vasconcelos Cunha; Zardetto, Cristina Giovannetti Del Conte; Moura-Netto, Cacio; Wanderley, Marcia Turolla

The aim of this study was to standardize the nomenclature of pulp alteration to pulp calcification (PC) and to classify it according to type, quantity and location, as well as relate it to clinical and radiographic features. The dental records of 946 patients from the Research and Clinical Center for Dental Trauma in Primary Teeth were studied. Two hundred and fifty PC-traumatized upper deciduous incisors were detected. According to radiographic analysis of the records, 62.5% showed diffuse calcification, 36.3% tube-like calcification, and 1.2% concentric calcification. According to the extension of pulp calcification, the records showed: 80% partial calcification, 17.2% total coronal calcification and partial radicular calcification, and 2.8 % total coronal and radicular calcification. As for location, only 2.4% were on the coronal pulp, 5.2% on the radicular pulp and 92.4% on both radicular and coronal pulp. Regarding coronal discoloration, 54% were yellow and 2% gray. In relation to periradicular changes, 10% showed widened periodontal ligament space, 3.1% internal resorption, 10% external resorption, 10.4% periapical bone rarefaction. Since PC is a general term, it is important to classify it and correlate it to clinical and radiographic changes, in order to establish the correct diagnosis, treatment and prognosis of each case.

Multi-spacecraft Observations of the Rotation and Nonradial Motion of a CME Flux Rope Causing an Intense Geomagnetic Storm

NASA Astrophysics Data System (ADS)

Liu, Yi A.; Liu, Ying D.; Hu, Huidong; Wang, Rui; Zhao, Xiaowei

2018-02-01

We present an investigation of the rotation and nonradial motion of a coronal mass ejection (CME) from AR 12468 on 2015 December 16 using observations from SDO, SOHO, STEREO A, and Wind. The EUV and HMI observations of the source region show that the associated magnetic flux rope (MFR) axis pointed to the east before the eruption. We use a nonlinear force-free field (NLFFF) extrapolation to determine the configuration of the coronal magnetic field and calculate the magnetic energy density distributions at different heights. The distribution of the magnetic energy density shows a strong gradient toward the northeast. The propagation direction of the CME from a Graduated Cylindrical Shell (GCS) modeling deviates from the radial direction of the source region by about 45° in longitude and about 30° in latitude, which is consistent with the gradient of the magnetic energy distribution around the AR. The MFR axis determined by the GCS modeling points southward, which has rotated counterclockwise by about 95° compared with the orientation of the MFR in the low corona. The MFR reconstructed by a Grad–Shafranov (GS) method at 1 au has almost the same orientation as the MFR from the GCS modeling, which indicates that the MFR rotation occurred in the low corona. It is the rotation of the MFR that caused the intense geomagnetic storm with the minimum D st of ‑155 nT. These results suggest that the coronal magnetic field surrounding the MFR plays a crucial role in the MFR rotation and propagation direction.

Persistent Doppler Shift Oscillations Observed with HINODE-EIS in the Solar Corona: Spectroscopic Signatures of Alfvenic Waves and Recurring Upflows

NASA Technical Reports Server (NTRS)

Tian, Hui; McIntosh, Scott W.; Wang, Tongjiang; Offman, Leon; De Pontieu, Bart; Innes, Davina E.; Peter, Hardi

2012-01-01

Using data obtained by the EUV Imaging Spectrometer on board Hinode, we have performed a survey of obvious and persistent (without significant damping) Doppler shift oscillations in the corona. We have found mainly two types of oscillations from February to April in 2007. One type is found at loop footpoint regions, with a dominant period around 10 minutes. They are characterized by coherent behavior of all line parameters (line intensity, Doppler shift, line width, and profile asymmetry), and apparent blueshift and blueward asymmetry throughout almost the entire duration. Such oscillations are likely to be signatures of quasi-periodic upflows (small-scale jets, or coronal counterpart of type-II spicules), which may play an important role in the supply of mass and energy to the hot corona. The other type of oscillation is usually associated with the upper part of loops. They are most clearly seen in the Doppler shift of coronal lines with formation temperatures between one and two million degrees. The global wavelets of these oscillations usually peak sharply around a period in the range of three to six minutes. No obvious profile asymmetry is found and the variation of the line width is typically very small. The intensity variation is often less than 2%. These oscillations are more likely to be signatures of kink/Alfv´en waves rather than flows. In a few cases, there seems to be a p/2 phase shift between the intensity and Doppler shift oscillations, which may suggest the presence of slow-mode standing waves according to wave theories. However, we demonstrate that such a phase shift could also be produced by loops moving into and out of a spatial pixel as a result of Alfv´enic oscillations. In this scenario, the intensity oscillations associated with Alfv´enic waves are caused by loop displacement rather than density change. These coronal waves may be used to investigate properties of the coronal plasma and magnetic field.

Measurements of electron density and temperature profiles in plasma produced by Nike KrF laser for laser plasma instability research.

PubMed

Oh, Jaechul; Weaver, J L; Karasik, M; Chan, L Y

2015-08-01

A grid image refractometer (GIR) has been implemented at the Nike krypton fluoride laser facility of the Naval Research Laboratory. This instrument simultaneously measures propagation angles and transmissions of UV probe rays (λ = 263 nm, Δt = 10 ps) refracted through plasma. We report results of the first Nike-GIR measurement on a CH plasma produced by the Nike laser pulse (∼1 ns FWHM) with the intensity of 1.1 × 10(15) W/cm(2). The measured angles and transmissions were processed to construct spatial profiles of electron density (ne) and temperature (Te) in the underdense coronal region of the plasma. Using an inversion algorithm developed for the strongly refracted rays, the deployed GIR system probed electron densities up to 4 × 10(21) cm(-3) with the density scale length of 120 μm along the plasma symmetry axis. The resulting n(e) and T(e) profiles are verified to be self-consistent with the measured quantities of the refracted probe light.

Millisecond radio spikes from the dwarf M flare star AD Leonis

NASA Technical Reports Server (NTRS)

Lang, K. R.; Willson, R. F.

1986-01-01

Arecibo radio observations of millisec bursts of radio signals at 1415 MHz from AD Leonis are reported. The observed burst had an ellipticity of 0.95, 50-100 percent circular polarization, and a flux density maximum of 30 mJy. The 50 sec burst featured five quasi-periodic oscillations with a mean periodicity of about 3.2 sec. A second, less intense burst that occurred 20 sec later was 100 percent circularly polarized. The area emitting the bursts covered an estimated 0.005 of the radius of AD Leonis and had an electron density of 6 billion/cu cm and a longitudinal magnetic field strength of 250 gauss, if the source was an electron-cyclotron maser. A coherent plasma source would require, for the first harmonic, an electron density of 20 billion/cu cm and a magnetic field much less than 500 gauss. A second harmonic of the plasma frequency would require an electron density of 6 billion/cu cm and a field strength much less than 250 gauss. The possibility that the source was periodic oscillations in coronal loops is discussed.

An evolving trio of hybrid stars: C111

NASA Technical Reports Server (NTRS)

Sonneborn, George (Technical Monitor); Dupree, Andrea K.

2005-01-01

Hybrid stars are a class of cool, luminous single stars originally identified based on the appearance of their ultraviolet IUE spectra. C IV emission is present (signifying temperatures of at least lo5 K), and asymmetric emission cores of Mg I1 are found, accompanied by absorption features at low and high velocities, indicating a massive stellar wind and circumstellar material. Many members of this class have been identified and X-rays have been detected from most hybrids. They represent the critical evolutionary state between coronal-like objects and the Alpha Ori-like objects and assume a pivotal role in the definition of coronal evolution, atmospheric heating processes, and mechanisms to drive winds of cool stars.

Micro-shear bond strengths of adhesive resins to coronal dentin versus the floor of the pulp chamber.

PubMed

Toba, Shigemitsu; Veerapravati, Weeraporn; Shimada, Yasushi; Nikaido, Toru; Tagami, Junji

2003-09-01

To evaluate the micro-shear bond strengths to superficial coronal dentin and the floor of the pulp chamber using two dentin bonding systems and to compare the ultrastructure of the resin-dentin interface of the two regions. 30 non-carious molars were used to obtain 2 mm thick slabs of coronal dentin and dentin at the pulp chamber. The specimens in each region were divided into three sub-groups to be bonded as follows; Clearfil SE Bond was used according to the manufacturer's instructions, Single Bond was applied to either wet dentin (Blot dry Group) or air-dried dentin (Dry Group) after phosphoric acid etching. A resin composite cylinder 0.5 mm high and 0.75 mm in diameter formed using a vinyl tube was bonded to the dentin. Specimens were stored at 37 degrees C for 24 hours in water and then stressed in shear at a crosshead speed of 1 mm/minute. The data were analyzed with one-way ANOVA and Fisher's PLSD test at the 5% level of significance. In addition, the ultrastructure of cross-sectioned dentin surfaces, the conditioned dentin surface and the resin dentin interfaces were observed by SEM. The bond strengths of Clearfil SE Bond and the Single Bond Blot dry group were approximately 40 MPa in coronal dentin and 30 MPa in the dentin at the floor of the pulp chamber respectively. However, the bond strengths of Single Bond were significantly lower in the Dry condition (MPa) (P < 0.05). SEM observations revealed the thickness of the hybrid layer created by Clearfil SE Bond in coronal dentin and at the floor of the pulp chamber were less than 1.0 microm thick. For Single Bond, a 3-4 microm hybrid layer was created in coronal dentin, while a thinner hybrid layer was observed in the floor of the pulp chamber. Morphological and structural variations in dentin may have influenced the bond strengths of the bonding systems to the floor of the pulp chamber.

Thermodynamics of the Solar Corona and Evolution of the Solar Magnetic Field as Inferred from the Total Solar Eclipse Observations of 11 July 2010

NASA Technical Reports Server (NTRS)

Habbal, Shadia Rifai; Druckmueller, Miloslav; Morgan, Huw; Ding, Adalbert; Johnson, Judd; Druckmuellerova, Hana; Daw, Adrian; Arndt, Martina B.; Dietzel, Martin; Saken, Jon

2011-01-01

We report on multi-wavelength observations of the corona taken simultaneously in broadband white light, and in seven spectral lines, H-alpha 656.3 nm, Fe IX 435.9 nm, Fe X 637.4 nm, Fe XI 789.2 nm, Fe XIII 1074.7 nm, Fe XIV 530.3 nm and Ni XV 670.2 nm. The observations were made during the total solar eclipse of 11 July 2010 from the atoll of Tatakoto in French Polynesia. Simultaneous imaging with narrow bandpass filters in each of these spectral lines and in their corresponding underlying continua maximized the observing time during less than ideal observing conditions and yielded outstanding quality data. The application of two complementary image processing techniques revealed the finest details of coronal structures at 1" resolution in white light, and 6.5" in each of the spectral lines. This comprehensive wavelength coverage confirmed earlier eclipse findings that the solar corona has a clear two-temperature structure: The open field lines, expanding outwards from the solar surface, are characterized by electron temperatures near 1 X 10(exp 6) K, while the hottest plasma around 2X 10(exp 6) K resides in loop-like structures forming the bulges of streamers. The first images of the corona in the forbidden lines of Fe IX and Ni XV, showed that there was very little coronal plasma at temperatures below 5 X 10(exp 5) K and above 2.5X 10(exp 6) K. The data also enabled temperature differentiations as low as 0:2 X 10(exp 6) K in different density structures. These observations showed how the passage of CMEs through the corona, prior to totality, produced large scale ripples and very sharp streaks, which could be identified with distinct temperatures for the first time. The ripples were most prominent in emission from spectral lines associated with temperatures around 10(exp 6) K. The most prominent streak was associated with a conical-shaped void in the emission from the coolest line of Fe IX and from the hottest line of Ni XV. A prominence, which erupted prior to totality, appeared in the shape of a hook in the cooler lines of Fe X and Fe XI, spanning 0.5 R(solar) in extent starting at a heliocentric distance of 1.3 R(solar), with a complex trail of hot and cool twisted structures connecting it to the solar surface. Simultaneous Fe X 17.4 nm observations from space by Proba2/SWAP provided an ideal opportunity for comparing emission from a coronal forbidden line, namely Fe X 637.4 nm, with a space-based EUV allowed line. Comparison of the Fe X 17.4 nm and 637.4 nm emission provided the first textbook example of the role of radiative excitation in extending the detectability of coronal emission to much larger heliocentric distances than its collisionally excited component. These eclipse observations demonstrate the unique capabilities of coronal forbidden lines for exploring the evolution of the coronal magnetic field in the heliocentric distance range of 1 - 3 R(solar), which is currently inaccessible to any space-borne or ground-based observatory.

Event Study of a Persistent Coronal Hole, its Solar Wind Signatures at L1, and Recurrent Relativistic Electron Enhancements at Geostationary Orbit

NASA Astrophysics Data System (ADS)

Rodriguez, Juan; Krista, Larisza

2017-04-01

Enhancements of relativistic electrons in Earth's radiation belts statistically exhibit a 27-day periodicity that is attributable to the interaction of corotating interaction regions (CIRs) with the Earth's magnetosphere. These CIRs are the interfaces between tenuous, high-speed solar wind streams (HSS) emitted by coronal holes (CH) and the denser, slower solar wind emitted from the quiet Sun (QS). At these stream interfaces (SI), the plasma is compressed, resulting in increased number density and magnetic field. Subsequent relativistic electron enhancements have been attributed to southward interplanetary magnetic field (IMF Bz). This includes southward Bz intensified within the CIR as well as southward Bz associated with Alfvenic turbulence in the following HSS. Although this chain of events is broadly accepted, few studies have studied in depth the evolution of a single persistent CH, its solar wind signatures at L1, and associated recurrent relativistic electron enhancements in the radiation belts. During the second half of 2003, a persistent CH was observed in the northern hemisphere of the Sun. The resulting CIR caused recurrent enhancements in the relativistic electron fluxes observed by the GOES satellites. During these enhancements, the >2 MeV electrons increased from dropout (instrument background) levels to hazardous levels more than an order-of-magnitude greater than the NOAA SWPC alert level. Moreover, for the first time in Solar Cycle 23 (SC23) the >4 MeV electron fluxes exceeded 100 electrons/(cm**2 s sr). This happened in five recurrent extended relativistic electron enhancement events during this period. In context, only five such events with >4 MeV electron fluxes exceeding 100 electrons/(cm**2 s sr) occurred during the rest of SC23, and not in a recurrent fashion. Using this as a geoeffectiveness criterion, neither other CHs during this period, nor the coronal mass ejections (CMEs) in later October and November were as geoeffective as this persistent CH. This paper addresses the question: how do the properties of this particularly geoeffective CH and its solar wind manifestations at 1 AU vary from rotation to rotation and how is it distinguished from less geoeffective CHs (and ICMEs) during the same period? The Coronal Hole Automated Recognition and Monitoring (CHARM; Krista and Gallagher, 2009) algorithm is used to identify CHs and to quantify their physical properties (e.g., boundary, area, magnetic field strength and polarity). The Minor Storm (MiSt) algorithm is used to link the CHs to their in situ signatures (e.g., IMF, velocity, number density, temperature) observed by the Advanced Composition Explorer (ACE) satellite. The properties of the CHs and associated geoeffective solar wind properties are evaluated and compared, as well as the Dst geomagnetic index. With these results, we determine whether any of the characteristics of the CHs and their in situ solar wind signatures distinguish them in their relative geoeffectiveness.

Three-Dimensional Structure and Energy Balance of a Coronal Mass Ejection

NASA Technical Reports Server (NTRS)

Lee, J.-Y.; Raymond, J. C.; Ko, Y.-K.; Kim, K.-S.

2009-01-01

UVCS observed Doppler-shifted material of a partial halo coronal mass ejection (CME) on 2001 December 13. The observed ratio of [O VJ/O V] is a reliable density diagnostic important for assessing the state of the plasma. Earlier UVCS observations of CMEs found evidence that the ejected plasma is heated long after the eruption. This paper investigated the heating rates, which represent a significant fraction of the CME energy budget. The parameterized heating and radiative and adiabatic cooling have been used to evaluate the temperature evolution of the CME material with a time-dependent ionization state model. Continuous heating is required to match the UVCS observations. To match the O VI bright knots, a higher heating rate is required such that the heating energy is greater than the kinetic energy.

The Evolution of Transition Region Loops Using IRIS and AIA

NASA Technical Reports Server (NTRS)

Winebarger, Amy R.; DePontieu, Bart

2014-01-01

Over the past 50 years, the model for the structure of the solar transition region has evolved from a simple transition layer between the cooler chromosphere to the hotter corona to a complex and diverse region that is dominated by complete loops that never reach coronal temperatures. The IRIS slitjaw images show many complete transition region loops. Several of the "coronal" channels in the SDO AIA instrument include contributions from weak transition region lines. In this work, we combine slitjaw images from IRIS with these channels to determine the evolution of the loops. We develop a simple model for the temperature and density evolution of the loops that can explain the simultaneous observations. Finally, we estimate the percentage of AIA emission that originates in the transition region.

Flow properties of the solar wind obtained from white light data, Ulysses observations and a two-fluid model

NASA Technical Reports Server (NTRS)

Habbal, Shadia Rifai; Esser, Ruth; Guhathakurta, Madhulika; Fisher, Richard

1995-01-01

Using the empirical constraints provided by observations in the inner corona and in interplanetary space. we derive the flow properties of the solar wind using a two fluid model. Density and scale height temperatures are derived from White Light coronagraph observations on SPARTAN 201-1 and at Mauna Loa, from 1.16 to 5.5 R, in the two polar coronal holes on 11-12 Apr. 1993. Interplanetary measurements of the flow speed and proton mass flux are taken from the Ulysses south polar passage. By comparing the results of the model computations that fit the empirical constraints in the two coronal hole regions, we show how the effects of the line of sight influence the empirical inferences and subsequently the corresponding numerical results.

Analysis of the gutta-percha filled area in C-shaped mandibular molars obturated with a modified MicroSeal technique.

PubMed

Ordinola-Zapata, R; Bramante, C M; de Moraes, I G; Bernardineli, N; Garcia, R B; Gutmann, J L

2009-03-01

To analyse the gutta-percha filled area of C-shaped molar teeth root filled with the modified MicroSeal technique with reference to the radiographic features and the C-shaped canal configuration. Twenty-three mandibular second molar teeth with C-shaped roots were classified according to their radiographic features as: type I--merging, type II--symmetrical and type III--asymmetrical. The canals were root filled using a modified technique of the MicroSeal system. Horizontal sections at intervals of 600 mum were made 1 mm from the apex to the subpulpal floor level. The percentage of gutta-percha area from the apical, middle and coronal levels of the radiographic types was analysed using the Kruskal-Wallis test. Complementary analysis of the C-shaped canal configurations (C1, C2 and C3) determined from cross-sections from the apical third was performed in a similar way. No significant differences were found between the radiographic types in terms of the percentage of gutta-percha area at any level (P > 0.05): apical third, type I: 77.04%, II: 70.48% and III: 77.13%, middle third, type I: 95.72%, II: 93.17%, III: 91.13% and coronal level, type I: 98.30%, II: 98.25%, III: 97.14%. Overall, the percentage of the filling material was lower in the apical third (P < 0.05). No significant differences were found between the C-shaped canal configurations apically; C1: 72.64%, C2: 79.62%, C3: 73.51% (P > 0.05). The percentage of area filled with gutta-percha was similar in the three radiographic types and canal configuration categories of C-shaped molars. These results show the difficulty of achieving predictable filling of the root canal system when this anatomical variation exists. In general, the apical third was less completely filled.

Evolution and Activity in the Solar Corona: A Comparison of Coronal and Chromospheric Structures Seen in Soft X-Rays, White Light and H-Alpha Emission

NASA Technical Reports Server (NTRS)

Bagenal, Fran

2001-01-01

The work completed under this project, 'Evolution and Activity in the Solar Corona: A Comparison of Coronal and Chromospheric Structures Seen in Soft X-Rays, White Light and H-Alpha Emission', includes the following presentations: (1) Analysis of H-alpha Observations of High-altitude Coronal Condensations; (2) Multi-spectral Imaging of Coronal Activity; (3) Measurement and Modeling of Soft X-ray Loop Arcades; (4) A Study of the Origin and Dynamics of CMEs; and various poster presentations and thesis dissertations.

Volume and tissue composition preserving deformation of breast CT images to simulate breast compression in mammographic imaging

NASA Astrophysics Data System (ADS)

Han, Tao; Chen, Lingyun; Lai, Chao-Jen; Liu, Xinming; Shen, Youtao; Zhong, Yuncheng; Ge, Shuaiping; Yi, Ying; Wang, Tianpeng; Shaw, Chris C.

2009-02-01

Images of mastectomy breast specimens have been acquired with a bench top experimental Cone beam CT (CBCT) system. The resulting images have been segmented to model an uncompressed breast for simulation of various CBCT techniques. To further simulate conventional or tomosynthesis mammographic imaging for comparison with the CBCT technique, a deformation technique was developed to convert the CT data for an uncompressed breast to a compressed breast without altering the breast volume or regional breast density. With this technique, 3D breast deformation is separated into two 2D deformations in coronal and axial views. To preserve the total breast volume and regional tissue composition, each 2D deformation step was achieved by altering the square pixels into rectangular ones with the pixel areas unchanged and resampling with the original square pixels using bilinear interpolation. The compression was modeled by first stretching the breast in the superior-inferior direction in the coronal view. The image data were first deformed by distorting the voxels with a uniform distortion ratio. These deformed data were then deformed again using distortion ratios varying with the breast thickness and re-sampled. The deformation procedures were applied in the axial view to stretch the breast in the chest wall to nipple direction while shrinking it in the mediolateral to lateral direction re-sampled and converted into data for uniform cubic voxels. Threshold segmentation was applied to the final deformed image data to obtain the 3D compressed breast model. Our results show that the original segmented CBCT image data were successfully converted into those for a compressed breast with the same volume and regional density preserved. Using this compressed breast model, conventional and tomosynthesis mammograms were simulated for comparison with CBCT.

Birth, life, and death of a solar coronal plume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pucci, Stefano; Romoli, Marco; Poletto, Giannina

2014-10-01

We analyze a solar polar-coronal-hole (CH) plume over its entire ≈40 hr lifetime, using high-resolution Solar Dynamic Observatory Atmospheric Imaging Assembly (AIA) data. We examine (1) the plume's relationship to a bright point (BP) that persists at its base, (2) plume outflows and their possible contribution to the solar wind mass supply, and (3) the physical properties of the plume. We find that the plume started ≈2 hr after the BP first appeared and became undetectable ≈1 hr after the BP disappeared. We detected radially moving radiance variations from both the plume and from interplume regions, corresponding to apparent outflowmore » speeds ranging over ≈(30-300) km s{sup –1} with outflow velocities being higher in the 'cooler' AIA 171 Å channel than in the 'hotter' 193 Å and 211 Å channels, which is inconsistent with wave motions; therefore, we conclude that the observed radiance variations represent material outflows. If they persist into the heliosphere and plumes cover ≈10% of a typical CH area, these flows could account for ≈50% of the solar wind mass. From a differential emission measure analysis of the AIA images, we find that the average electron temperature of the plume remained approximately constant over its lifetime, at T {sub e} ≈ 8.5 × 10{sup 5} K. Its density, however, decreased with the age of the plume, being about a factor of three lower when the plume faded compared to when it was born. We conclude that the plume died due to a density reduction rather than to a temperature decrease.« less

Coronal magnetic fields and the solar wind

NASA Technical Reports Server (NTRS)

Newkirk, G., Jr.

1972-01-01

Current information is presented on coronal magnetic fields as they bear on problems of the solar wind. Both steady state fields and coronal transient events are considered. A brief critique is given of the methods of calculating coronal magnetic fields including the potential (current free) models, exact solutions for the solar wind and field interaction, and source surface models. These solutions are compared with the meager quantitative observations which are available at this time. Qualitative comparisons between the shapes of calculated magnetic field lines and the forms visible in the solar corona at several recent eclipses are displayed. These suggest that: (1) coronal streamers develop above extended magnetic arcades which connect unipolar regions of opposite polarity; and (2) loops, arches, and rays in the corona correspond to preferentially filled magnetic tubes in the approximately potential field.

Deproteinized Bovine Bone Mineral or Autologous Bone at Dehiscence Type Defects at Implants Installed Immediately into Extraction Sockets: An Experimental Study in Dogs.

PubMed

Pereira, Flavia Priscila; De Santis, Enzo; Hochuli-Vieira, Eduardo; de Souza Faco, Eduardo F; Pantani, Fabio; Salata, Luiz A; Botticelli, Daniele

2016-06-01

The aim of this study was to evaluate bone regeneration at surgically created dehiscence buccal defects at implants placed immediately into extraction sockets (IPIES) of small dimensions filled with autogenous bone or deproteinized bovine bone mineral (DBBM) associated with a collagen membrane. Eight Labrador dogs were used and implants were placed immediately into the extraction sockets of the second premolar. The buccal wall was subsequently removed to create a standardized defect, 4 mm wide coronally, 2 mm wide apically, and 6 mm high. Autogenous bone particles (AB) or DBBM granules were used to fill the defects. All surgical sites were subsequently covered by a resorbable collagen membrane and a non-submerged healing was allowed. After 4 months, the animals were euthanized and bone blocks harvested and processed for histomorphometric analysis. The bony crest at the buccal aspect (C) was located 2.3 ± 0.8 mm and 1.7 ± 0.7 mm apically to the implant shoulder (IS) at the AB and DBBM sites, respectively. The coronal levels of osseointegration at the buccal aspect (B) were located 2.7 ± 0.7 mm and 2.2 ± 1.0 mm apically to IS at the AB and DBBM sites, respectively. At the AB sites, the peri-implant mucosa was located 4.3 ± 0.9 mm, 4.7 ± 0.9 mm, and 2.0 ± 1.6 mm coronally to C, B, and IS, respectively. The corresponding values at the DBBM sites were 4.3 ± 0.6 mm, 4.8 ± 0.6 mm, and 2.5 ± 0.8 mm, respectively. No statistically significant differences were found. The treatment of surgically created buccal defects at IPIES sites using Bio-Oss® (Geistlich Biomaterials, Wolhusen, LU, Switzerland) or autogenous bone, concomitantly with a collagen membrane, engenders bone regeneration to a similar extent after 4 months of healing. © 2015 Wiley Periodicals, Inc.

On Heating the Sun's Corona by Magnetic Explosions: Feasibility in Active Regions and prospects for Quiet Regions and Coronal Holes

NASA Technical Reports Server (NTRS)

Moore, Ronald L.; Falconer, D. A.; Porter, Jason G.; Suess, Steven T.

1999-01-01

We build a case for the persistent strong coronal heating in active regions and the pervasive quasi-steady heating of the corona in quiet regions and coronal holes being driven in basically the same way as the intense transient heating in solar flares: by explosions of sheared magnetic fields in the cores of initially closed bipoles. We begin by summarizing the observational case for exploding sheared core fields being the drivers of a wide variety of flare events, with and without coronal mass ejections. We conclude that the arrangement of an event's flare heating, whether there is a coronal mass ejection, and the time and place of the ejection relative to the flare heating are all largely determined by four elements of the form and action of the magnetic field: (1) the arrangement of the impacted, interacting bipoles participating in the event, (2) which of these bipoles are active (have sheared core fields that explode) and which are passive (are heated by injection from impacted active bipoles), (3) which core field explodes first, and (4) which core-field explosions are confined within the closed field of their bipoles and which ejectively open their bipoles. We then apply this magnetic-configuration framework for flare heating to the strong coronal heating observed by the Yohkoh Soft X-ray Telescope in an active region with strongly sheared core fields observed by the MSFC vector magnetograph. All of the strong coronal heating is in continually microflaring sheared core fields or in extended loops rooted against the active core fields. Thus, the strong heating occurs in field configurations consistent with the heating being driven by frequent core-field explosions that are smaller but similar to those in confined flares and flaring arches. From analysis of the thermal and magnetic energetics of two selected core-field microflares and a bright extended loop, we find that (1) it is energetically feasible for the sheared core fields to drive all of the coronal heating in the active region via a staccato of magnetic microexplosions, (2) the microflares at the feet of the extended loop behave as the flares at the feet of flaring arches in that more coronal heating is driven within the active bipole than in the extended loop, (3) the filling factor of the X-ray plasma in the core field microflares and in the extended loop is approximately 0.1, and (4) to release enough magnetic energy for a typical microflare (10^27 - 10^28 erg), a microflaring strand of sheared core field need expand and/or untwist by only a few percent at most. Finally, we point out that (1) the field configurations for strong coronal heating in our example active region (i.e., neutral-line core fields, many embedded in the feet of extended loops) are present in abundance in the magnetic network in quiet regions and coronal holes, and (2) it is known that many network bipoles do microflare and that many produce detectable coronal heating. We therefore propose that exploding sheared core fields are the drivers of most of the heating and dynamics of the solar atmosphere, ranging from the largest and most powerful coronal mass ejections and flares, to the vigorous microflaring and coronal heating in active regions, to the multitude of fine-scale explosive events in the magnetic network. The low-lysing exploding core fields in the network drive microflares, spicules, global coronal heating, and ,consequently, the solar wind.

Research in solar plasma theory

NASA Technical Reports Server (NTRS)

Vanhoven, Gerard

1992-01-01

The main thrust and significance of our research results are presented. The topics covered include: (1) coronal structure and dynamics; (2) coronal heating; (3) filament formation; and (4) flare energy release.

On Heating Large Bright Coronal Loops by Magnetic Microexplosions at their Feet

NASA Technical Reports Server (NTRS)

Moore, Ronald L; Falconer, D. A.; Porter, Jason G.

1999-01-01

In previous work, by registering Yohkoh SXT coronal X-ray images with MSFC vector magnetograms, we found that: (1) many of the larger bright coronal loops rooted at one or both ends in an active region are rooted around magnetic islands of included polarity, (2) the core field encasing the neutral line encircling the island is strongly sheared, and (3) this sheared core field is the seat of frequent microflares. This suggests that the coronal heating in these extended bright loops is driven by many small explosive releases of stored magnetic energy from the sheared core field at their feet, some of which magnetic microexplosions also produce the microflare heating in the core fields. In this paper, we show that this scenario is feasible in terms of the energy Abstract: required for the observed coronal heating and the magnetic energy available in the observed sheared core fields. In a representative active region, from the X-ray and vector field data, we estimate the coronal heating consumption by a selected typical large bright loop, the coronal heating consumption by a typical microflare at the foot of this loop, the frequency of microflares at the foot, and the available magnetic energy in the microflaring core field. We find that: (1) the rate of magnetic energy release to power the microflares at the foot (approx. 6 x 10(ext 25)erg/s) is enough to also power the coronal heating in the body of the extended loop (approx. 2 x l0(exp 25 erg/s), and (2) there is enough stored magnetic energy in the sheared core field to sustain the microflaring and extended loop heating for about a day, which is a typical time for buildup of neutral-line magnetic shear in an active region. This work was funded by the Solar Physics Branch of NASA's Office of Space Science through the SR&T Program and the SEC Guest Investigator Program.

Hemispheric asymmetry in coronal hole evolution: Cause of the bashful ballerina?

NASA Astrophysics Data System (ADS)

Mursula, K.; Tlatov, A.; Virtanen, I.

2012-12-01

The magnetic hemisphere prevalent in the solar northern hemisphere has been shown to cover a larger area than in the south for about three years in the declining phase of several solar cycles. Correspondingly, the average field intensity is weaker in the northern hemisphere and the heliospheric current sheet (HCS) is shifted southward at these times. This phenomenon, now called the bashful ballerina, has been verified using several databases and methods, including the in situ observations of the heliospheric magnetic field (HMF) at 1 AU by the OMNI data base, at about 2 AU by the Ulysses probe, and at different radial distances by the Voyager 1 and 2 and Pioneer 10 and 11 probes. The Ulysses observations show that the mean southward shift of the HCS was about 2 degrees in the declining phase of both cycle 22 and cycle 23, although the polar strengths were very different between the two cycles. The HMF observations by the Voyager and Pioneer probes show a very consistent structure of HMF sectors and HCS location in the entire heliosphere, and even beyond the termination shock. Moreover, they suggest a systematic difference in the development of northern and southern polar coronal holes. While the northern coronal holes developed very systematically during all the four solar minima since mid-1970s, the evolution of southern coronal holes was less systematic and delayed with respect to the northern hemisphere. This delay in the evolution of southern coronal holes leads to a larger extent of northern coronal holes and a southward shift of the heliospheric current sheet (the bashful ballerina phenomenon) for a few years in the declining phase of the solar cycle. Here we study direct observations of solar coronal holes and verify this difference in the evolution of coronal holes between the two solar hemispheres, which explains the bashful ballerina phenomenon.

IMAGING AND SPECTROSCOPIC OBSERVATIONS OF A TRANSIENT CORONAL LOOP: EVIDENCE FOR THE NON-MAXWELLIAN κ-DISTRIBUTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dudík, Jaroslav; Mackovjak, Šimon; Dzifčáková, Elena

2015-07-10

We report on the Solar Dynamics Observatory/Atmospheric Imaging Assembly (AIA) and Hinode/EUV Imaging Spectrograph (EIS) observations of a transient coronal loop. The loop brightens up in the same location after the disappearance of an arcade formed during a B8.9-class microflare 3 hr earlier. EIS captures this loop during its brightening phase, as observed in most of the AIA filters. We use the AIA data to study the evolution of the loop, as well as to perform the differential emission measure (DEM) diagnostics as a function of κ. The Fe xi–Fe xiii lines observed by EIS are used to perform themore » diagnostics of electron density and subsequently the diagnostics of κ. Using ratios involving the Fe xi 257.772 Å self-blend, we diagnose κ ≲ 2, i.e., an extremely non-Maxwellian distribution. Using the predicted Fe line intensities derived from the DEMs as a function of κ, we show that, with decreasing κ, all combinations of ratios of line intensities converge to the observed values, confirming the diagnosed κ ≲ 2. These results represent the first positive diagnostics of κ-distributions in the solar corona despite the limitations imposed by calibration uncertainties.« less

Microphysics of Waves and Instabilities in the Solar Wind and their Macro Manifestations in the Corona and Interplanetary Space

NASA Technical Reports Server (NTRS)

Gurman, Joseph (Technical Monitor); Habbal, Shadia Rifai

2004-01-01

Investigations of the physical processes responsible for coronal heating and the acceleration of the solar wind were pursued with the use of our recently developed 2D MHD solar wind code and our 1D multifluid code. In particular, we explored (1) the role of proton temperature anisotropy in the expansion of the solar wind, (2) the role of plasma parameters at the coronal base in the formation of high speed solar wind streams at mid-latitudes, and (3) the heating of coronal loops.

Statistical Study of Solar Dimmings Using CoDiT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krista, Larisza D.; Reinard, Alysha A., E-mail: larisza.krista@noaa.gov

2017-04-10

We present the results from analyzing the physical and morphological properties of 154 dimmings (transient coronal holes) and the associated flares and coronal mass ejections (CMEs). Each dimming in our 2013 catalog was processed with the semi-automated Coronal Dimming Tracker using Solar Dynamics Observatory AIA 193 Å observations and HMI magnetograms. Instead of the typically used difference images, we used our coronal hole detection algorithm to detect transient dark regions “directly” in extreme ultraviolet (EUV) images. This allowed us to study dimmings as the footpoints of CMEs—in contrast with the larger, diffuse dimmings seen in difference images that represent themore » projected view of the rising, expanding plasma. Studying the footpoint-dimming morphology allowed us to better understand the CME structure in the low corona. While comparing the physical properties of dimmings, flares, and CMEs we were also able to identify relationships between the different parts of this complex eruptive phenomenon. We found that larger dimmings are longer-lived, suggesting that it takes longer to “close down” large open magnetic regions. Also, during their growth phase, smaller dimmings acquire a higher magnetic flux imbalance (i. e., become more unipolar) than larger dimmings. Furthermore, we found that the EUV intensity of dimmings (indicative of local electron density) correlates with how much plasma was removed and how energetic the eruption was. Studying the morphology of dimmings (single, double, fragmented) also helped us identify different configurations of the quasi-open magnetic field.« less

Simultaneous Solar Maximum Mission (SMM) and Very Large Array (VLA) observations of solar active regions

NASA Technical Reports Server (NTRS)

Willson, Robert F.

1991-01-01

Very Large Array observations at 20 cm wavelength can detect the hot coronal plasma previously observed at soft x ray wavelengths. Thermal cyclotron line emission was detected at the apex of coronal loops where the magnetic field strength is relatively constant. Detailed comparison of simultaneous Solar Maximum Mission (SMM) Satellite and VLA data indicate that physical parameters such as electron temperature, electron density, and magnetic field strength can be obtained, but that some coronal loops remain invisible in either spectral domain. The unprecedent spatial resolution of the VLA at 20 cm wavelength showed that the precursor, impulsive, and post-flare components of solar bursts originate in nearby, but separate loops or systems of loops.. In some cases preburst heating and magnetic changes are observed from loops tens of minutes prior to the impulsive phase. Comparisons with soft x ray images and spectra and with hard x ray data specify the magnetic field strength and emission mechanism of flaring coronal loops. At the longer 91 cm wavelength, the VLA detected extensive emission interpreted as a hot 10(exp 5) K interface between cool, dense H alpha filaments and the surrounding hotter, rarefield corona. Observations at 91 cm also provide evidence for time-correlated bursts in active regions on opposite sides of the solar equator; they are attributed to flare triggering by relativistic particles that move along large-scale, otherwise-invisible, magnetic conduits that link active regions in opposite hemispheres of the Sun.

Reconstruction of the forehead acoustic properties in an Indo-Pacific humpback dolphin (Sousa chinensis), with investigation on the responses of soft tissue sound velocity to temperature.

PubMed

Song, Zhongchang; Zhang, Yu; Berggren, Per; Wei, Chong

2017-02-01

Computed tomography (CT) imaging and ultrasound experimental measurements were combined to reconstruct the acoustic properties (density, velocity, and impedance) of the head from a deceased Indo-Pacific humpback dolphin (Sousa chinensis). The authors extracted 42 soft forehead tissue samples to estimate the sound velocity and density properties at room temperature, 25.0  °C. Hounsfield Units (HUs) of the samples were read from CT scans. Linear relationships between the tissues' HUs and velocity, and HUs and density were revealed through regression analyses. The distributions of the head acoustic properties at axial, coronal, and sagittal cross sections were reconstructed, suggesting that the forehead soft tissues were characterized by low-velocity in the melon, high-velocity in the muscle and connective tissues. Further, the sound velocities of melon, muscle, and connective tissue pieces were measured under different temperatures to investigate tissues' velocity response to temperature. The results demonstrated nonlinear relationships between tissues' sound velocity and temperature. This study represents a first attempt to provide general information on acoustic properties of this species. The results could provide meaningful information for understanding the species' bioacoustic characteristics and for further investigation on sound beam formation of the dolphin.

Sensitivity of coronal loop sausage mode frequencies and decay rates to radial and longitudinal density inhomogeneities: a spectral approach

NASA Astrophysics Data System (ADS)

Cally, Paul S.; Xiong, Ming

2018-01-01

Fast sausage modes in solar magnetic coronal loops are only fully contained in unrealistically short dense loops. Otherwise they are leaky, losing energy to their surrounds as outgoing waves. This causes any oscillation to decay exponentially in time. Simultaneous observations of both period and decay rate therefore reveal the eigenfrequency of the observed mode, and potentially insight into the tubes’ nonuniform internal structure. In this article, a global spectral description of the oscillations is presented that results in an implicit matrix eigenvalue equation where the eigenvalues are associated predominantly with the diagonal terms of the matrix. The off-diagonal terms vanish identically if the tube is uniform. A linearized perturbation approach, applied with respect to a uniform reference model, is developed that makes the eigenvalues explicit. The implicit eigenvalue problem is easily solved numerically though, and it is shown that knowledge of the real and imaginary parts of the eigenfrequency is sufficient to determine the width and density contrast of a boundary layer over which the tubes’ enhanced internal densities drop to ambient values. Linearized density kernels are developed that show sensitivity only to the extreme outside of the loops for radial fundamental modes, especially for small density enhancements, with no sensitivity to the core. Higher radial harmonics do show some internal sensitivity, but these will be more difficult to observe. Only kink modes are sensitive to the tube centres. Variation in internal and external Alfvén speed along the loop is shown to have little effect on the fundamental dimensionless eigenfrequency, though the associated eigenfunction becomes more compact at the loop apex as stratification increases, or may even displace from the apex.

Formation of Radio Type II Bursts During a Multiple Coronal Mass Ejection Event

NASA Astrophysics Data System (ADS)

Al-Hamadani, Firas; Pohjolainen, Silja; Valtonen, Eino

2017-12-01

We study the solar event on 27 September 2001 that consisted of three consecutive coronal mass ejections (CMEs) originating from the same active region, which were associated with several periods of radio type II burst emission at decameter-hectometer (DH) wavelengths. Our analysis shows that the first radio burst originated from a low-density environment, formed in the wake of the first, slow CME. The frequency-drift of the burst suggests a low-speed burst driver, or that the shock was not propagating along the large density gradient. There is also evidence of band-splitting within this emission lane. The origin of the first shock remains unclear, as several alternative scenarios exist. The second shock showed separate periods of enhanced radio emission. This shock could have originated from a CME bow shock, caused by the fast and accelerating second or third CME. However, a shock at CME flanks is also possible, as the density depletion caused by the three CMEs would have affected the emission frequencies and hence the radio source heights could have been lower than usual. The last type II burst period showed enhanced emission in a wider bandwidth, which was most probably due to the CME-CME interaction. Only one shock that could reliably be associated with the investigated CMEs was observed to arrive near Earth.

Solar radio bursts of spectral type II, coronal shocks, and optical coronal transients

NASA Technical Reports Server (NTRS)

Maxwell, A.; Dryer, M.

1981-01-01

An examination is presented of the association of solar radio bursts of spectral type II and coronal shocks with solar flare ejecta observed in H-alpha, the green coronal line, and white-light coronagraphs. It is suggested that fast-moving optical coronal transients should for the most part be identified with piston-type phenomena well behind the outward-traveling shock waves that generate type II radio bursts. A general model is presented which relates type II radio bursts and coronal shocks to optically observed ejecta and consists of three main velocity regimes: (1) a quasi-hemispherical shock wave moving outward from the flare at speeds of 1000-2000 km/sec and Alfven Mach number of about 1.5; (2) the velocity of the piston driving the shock, on the order of 0.8 that of the shock; and (3) the regime of the slower-moving H-alpha ejecta, with velocities of 300-500 km/sec.

Assessment of Coronal Spinal Alignment for Adult Spine Deformity Cases After Intraoperative T Square Shaped Use.

PubMed

Kurra, Swamy; Metkar, Umesh; Yirenkyi, Henaku; Tallarico, Richard A; Lavelle, William F

Retrospectively reviewed surgeries between 2011 and 2015 of patients who underwent posterior spinal deformity instrumentation with constructs involving fusions to pelvis and encompassing at least five levels. Measure the radiographic outcomes of coronal malalignment (CM) after use of an intraoperative T square shaped instrument in posterior spinal deformity surgeries with at least five levels of fusion and extension to pelvis. Neuromuscular children found to benefit from intraoperative T square technique to help achieve proper coronal spinal balance with extensive fusions. This intraoperative technique used in our posterior spine deformity instrumentation surgeries with the aforementioned parameters. There were 50 patients: n = 16 with intraoperative T square and n = 34 no-T square shaped device. Subgroups divided based on greater than 20 mm displacement and greater than 40 mm displacement of the C7 plumb line to the central sacral vertical line on either side in preoperative radiographs. We analyzed the demographics and the pre- and postoperative radiographic parameters of standing films: standing CM (displacement of C7 plumb line to central sacral vertical line), and major coronal Cobb angles in total sample and subgroups and compared T square shaped device with no-T square shaped device use by analysis of variance. A p value ≤.05 is statistically significant. In the total sample, though postoperative CM mean was not statistically different, we observed greater CM corrections in patients where a T square shaped device was used (70%) versus no-T square shaped device used (18%). In >20 mm and >40 mm subgroups, the postoperative mean CM values were statistically lower for the patients where a T square shaped device was used, p = .016 and p = .003, respectively. Cobb corrections were statistically higher for T square shaped device use in both >20 mm and >40 mm subgroups, 68%, respectively. The intraoperative T square shaped device technique had a positive effect on the amount of spine coronal malalignment correction after its use and for lumbar and thoracic coronal Cobb angles. Level III. Copyright © 2017 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.

The First Empirical Determination of the Fe10+ and Fe13+ Freeze-in Distances in the Solar Corona

NASA Astrophysics Data System (ADS)

Boe, Benjamin; Habbal, Shadia; Druckmüller, Miloslav; Landi, Enrico; Kourkchi, Ehsan; Ding, Adalbert; Starha, Pavel; Hutton, Joseph

2018-06-01

Heavy ions are markers of the physical processes responsible for the density and temperature distribution throughout the fine-scale magnetic structures that define the shape of the solar corona. One of their properties, whose empirical determination has remained elusive, is the “freeze-in” distance (R f ) where they reach fixed ionization states that are adhered to during their expansion with the solar wind. We present the first empirical inference of R f for {Fe}}{10+} and {Fe}}{13+} derived from multi-wavelength imaging observations of the corresponding Fe XI ({Fe}}{10+}) 789.2 nm and Fe XIV ({Fe}}{13+}) 530.3 nm emission acquired during the 2015 March 20 total solar eclipse. We find that the two ions freeze-in at different heliocentric distances. In polar coronal holes (CHs) R f is around 1.45 R ⊙ for {Fe}}{10+} and below 1.25 R ⊙ for {Fe}}{13+}. Along open field lines in streamer regions, R f ranges from 1.4 to 2 R ⊙ for {Fe}}{10+} and from 1.5 to 2.2 R ⊙ for {Fe}}{13+}. These first empirical R f values: (1) reflect the differing plasma parameters between CHs and streamers and structures within them, including prominences and coronal mass ejections; (2) are well below the currently quoted values derived from empirical model studies; and (3) place doubt on the reliability of plasma diagnostics based on the assumption of ionization equilibrium beyond 1.2 R ⊙.

Multi-thermal dynamics and energetics of a coronal mass ejection in the low solar atmosphere

NASA Astrophysics Data System (ADS)

Hannah, I. G.; Kontar, E. P.

2013-05-01

Aims: The aim of this work is to determine the multi-thermal characteristics and plasma energetics of an eruptive plasmoid and occulted flare observed by the Solar Dynamics Observatory's Atmospheric Imaging Assembly (SDO/AIA). Methods: We study a 2010 Nov. 3 event (peaking at 12:20 UT in GOES soft X-rays) of a coronal mass ejection and occulted flare that demonstrates the morphology of a classic erupting flux rope. The high spatial and time resolution and six coronal channels of the SDO/AIA images allows the dynamics of the multi-thermal emission during the initial phases of eruption to be studied in detail. The differential emission measure is calculated, using an optimized version of a regularized inversion method, for each pixel across the six channels at different times, resulting in emission measure maps and movies in a variety of temperature ranges. Results: We find that the core of the erupting plasmoid is hot (8-11, 11-14 MK) with a similarly hot filamentary "stem" structure connecting it to the lower atmosphere, which could be interpreted as the current sheet in the flux rope model, though is wider than these models suggest. The velocity of the leading edge of the eruption is 597-664 km s-1 in the temperature range ≥3-4 MK and between 1029-1246 km s-1 for ≤2-3 MK. We estimate the density (in 11-14 MK) of the erupting core and stem during the impulsive phase to be about 3 × 109 cm-3, 6 × 109 cm-3, 9 × 108 cm-3 in the plasmoid core, stem, and surrounding envelope of material. This gives thermal energy estimates of 5 × 1029 erg, 1 × 1029 erg, and 2 × 1030 erg. The kinetic energy for the core and envelope is slightly lower. The thermal energy of the core and current sheet grows during the eruption, suggesting continuous influx of energy presumably via reconnection. Conclusions: The combination of the optimized regularized inversion method and SDO/AIA data allows the multi-thermal characteristics (i.e. velocity, density, and thermal energies) of the plasmoid eruption to be determined. A movie is available in electronic form at http://www.aanda.org

The wide skirt of the bashful ballerina: Hemispheric asymmetry of the heliospheric magnetic field in the inner and outer heliosphere

NASA Astrophysics Data System (ADS)

Mursula, K.; Virtanen, I.

2012-04-01

We reanalyze the observations of the heliospheric magnetic field (HMF) made by the Pioneer 10 and 11 and Voyager 1 and 2 heliospheric probes since 1972, and calculate the HMF sector occurrence ratios and tangential component strengths in the different regions of the heliosphere. Observations at the distant probes and at 1 AU show a very consistent picture of the HMF sector structure in the entire heliosphere, and even beyond the termination shock. Pioneer 11 and Voyager 1 show that the development of northern polar coronal holes was very systematic and active during all the four solar minima since mid-1970s. On the other hand, Voyager 2 observations show a less systematic and delayed development of southern coronal holes in 1980s, 1990s and 2000s. This delay in the evolution of southern coronal holes with respect to the rapid and systematic evolution of northern coronal holes leads to a larger extent of northern coronal holes and a southward shift of the heliospheric current sheet (the bashful ballerina phenomenon) for a few years in the late declining phase of each solar cycle. HMF observations of the probes also directly verify the HCS southward shift, supporting earlier observations at 1-2 AU by the Ulysses probe and Earth-orbiting satellites and extending them into the more distant heliosphere. Although the evidence for the connection between the temporal difference in the evolution of polar coronal holes and the bashful ballerina times is based only on three solar cycles, this may be a common pattern for solar coronal hole evolution since the southward shift of the HCS has occurred at least since solar cycle 16.

The wide skirt of the bashful ballerina: Hemispheric asymmetry of the heliospheric magnetic field in the inner and outer heliosphere

NASA Astrophysics Data System (ADS)

Mursula, K.; Virtanen, I. I.

2012-08-01

We reanalyze the observations of the heliospheric magnetic field (HMF) made by the Pioneer 10 and 11 and Voyager 1 and 2 heliospheric probes since 1972, and calculate the HMF sector occurrence ratios and tangential component strengths in the different regions of the heliosphere. Observations at the distant probes and at 1 AU show a very consistent picture of the HMF sector structure in the entire heliosphere, and even beyond the termination shock. HMF observations by the probes also support the southward shift of the heliospheric current sheet (the bashful ballerina phenomenon), which is observed earlier at 1-2 AU by the Ulysses probe and Earth-orbiting satellites, and verify the HCS shift over a wide range of radial distances until the distant heliosphere. Pioneer 11 and Voyager 1 show that the development of northern polar coronal holes was very systematic and active during all the four solar minima since mid-1970s, while Voyager 2 observations show a less systematic and delayed development of southern coronal holes in 1980s, 1990s and 2000s. This delay in the evolution of southern coronal holes with respect to the rapid and systematic evolution of northern coronal holes leads to a larger extent of northern coronal holes and the southward shift of the HCS for a few years in the late declining phase of each solar cycle. Although evidence for the connection between the different evolution of polar coronal holes and the bashful ballerina phenomenon is obtained here only for three solar cycles, this may be a common pattern for solar coronal hole evolution since the southward shift of the HCS has occurred at least since solar cycle 16.

Polarization Observations of the Total Solar Eclipse of August 21, 2017

NASA Astrophysics Data System (ADS)

Burkepile, J.; Boll, A.; Casini, R.; de Toma, G.; Elmore, D. F.; Gibson, K. L.; Judge, P. G.; Mitchell, A. M.; Penn, M.; Sewell, S. D.; Tomczyk, S.; Yanamandra-Fisher, P. A.

2017-12-01

A total solar eclipse offers ideal sky conditions for viewing the solar corona. Light from the corona is composed of three components: the E-corona, made up of spectral emission lines produced by ionized elements in the corona; the K-corona, produced by photospheric light that is Thomson scattered by coronal electrons; and the F-corona, produced by sunlight scattered from dust particles in the near Sun environment and in interplanetary space. Polarized white light observations of the corona provide a way of isolating the K-corona to determine its structure, brightness, and density. This work focuses on broadband white light polarization observations of the corona during the upcoming solar eclipse from three different instruments. We compare coronal polarization brightness observations of the August 21, 2017 total solar eclipse from the NCAR/High Altitude Observatory (HAO) Rosetta Stone experiment using the 4-D Technology PolarCam camera with the two Citizen PACA_CATE17Pol telescopes that will acquire linear polarization observations of the eclipse and the NCAR/HAO K-Cor white light coronagraph observations from the Mauna Loa Solar Observatory in Hawaii. This comparison includes a discussion of the cross-calibration of the different instruments and reports the results of the coronal polarization brightness and electron density of the corona. These observations will be compared with results from previous coronal measurements taken at different phases of the solar cycle. In addition, we report on the performance of the three different polarimeters. The 4-D PolarCam uses a linear polarizer array, PACA_CATE17Pol uses a nematic liquid crystal retarder in a single beam configuration and K-Cor uses a pair of ferroelectric liquid crystal retarders in a dual-beam configuration. The use of the 4-D PolarCam camera in the Rosetta Stone experiment is to demonstrate the technology for acquiring high cadence polarization measurements. The Rosetta Stone experiment is funded through the NASA award NNH16ZDA001N-ISE. The Citizen Science approach to measuring the polarized solar corona during the eclipse is funded through NASA award NNX17AH76G. The NCAR Mauna Loa Solar Observatory is funded by the National Science Foundation.

The study of coronal plasma structures and fluctuations with Faraday rotation measurements

NASA Technical Reports Server (NTRS)

Sakurai, Takayuki; Sprangler, Steven R.

1994-01-01

We report dual-frequency, polarimetric measurements of Faraday rotation of extragalactic radio sources viewed through the solar corona. The observations were made at the Very Large Array in 1990 during solar maximum. Of the nine observed, an excess rotation measure of -12.6 rad/sq m was detected for one source (0010+005), which was observed at an elongation of about 9 solar radii. This measurement is in fair agreement with an a priori model rotation measure of -8.6 rad/sq m estimated from coronal potential field models and the electron density model of Paetzold et al. (1992). Our measurement provides a value for the coronal magnetic field strength at 9 solar radii given a knowledge of the magnetic field sector structure, of 12.5 +/- 2.3 mG. Rotation measurements of 0010+005 were made approximately once per hour over an 11 hr period. During this interval, a slow change of about 1 rad/sq m/hr in rotation measure was detected. Although we are not absolutely certain that this drift is not unremoved ionospheric Faraday rotation, extensive analysis of data from the other sources suggests that this is not the case (Sakurai & Spangler 1994). The very long timescale for this variation argues against the agency of magnetohydrodynamics (MHD) waves, and we suggest occultation of 0010+005 by relatively static plasma structures in the corona. We filtered our rotation measure time series to search for variations on an hourly timescale, such as those reported by Hollweg et al. (1992), which could be attributed to coronal MHD waves. We were unable to detect such fluctuations and can report only an upper limit to the rms variation of 1.6 rad/sq m. This upper limit is of the same order, but slightly larger than the values typically reported by Hollweg et al. (1982). This upper limit to the rotation measure fluctuations limits the dimensionless wave amplitude (delta B)/B in the corona to be less than 0.7. Using the number, we estimate the MHD wave flux at the coronal base to be less than 1.6 x 10(exp 5) ergs/sq cm/s. This is less than the amount of wave energy flux required by wave-driven models of the solar wind. Finally, we discuss a number of ways in which such observations could be improved in the future.

Navigated total knee arthroplasty: is it error-free?

PubMed

Chua, Kerk Hsiang Zackary; Chen, Yongsheng; Lingaraj, Krishna

2014-03-01

The aim of this study was to determine whether errors do occur in navigated total knee arthroplasty (TKAs) and to study whether errors in bone resection or implantation contribute to these errors. A series of 20 TKAs was studied using computer navigation. The coronal and sagittal alignments of the femoral and tibial cutting guides, the coronal and sagittal alignments of the final tibial implant and the coronal alignment of the final femoral implant were compared with that of the respective bone resections. To determine the post-implantation mechanical alignment of the limb, the coronal alignment of the femoral and tibial implants was combined. The median deviation between the femoral cutting guide and bone resection was 0° (range -0.5° to +0.5°) in the coronal plane and 1.0° (range -2.0° to +1.0°) in the sagittal plane. The median deviation between the tibial cutting guide and bone resection was 0.5° (range -1.0° to +1.5°) in the coronal plane and 1.0° (range -1.0° to +3.5°) in the sagittal plane. The median deviation between the femoral bone resection and the final implant was 0.25° (range -2.0° to 3.0°) in the coronal plane. The median deviation between the tibial bone resection and the final implant was 0.75° (range -3.0° to +1.5°) in the coronal plane and 1.75° (range -4.0° to +2.0°) in the sagittal plane. The median post-implantation mechanical alignment of the limb was 0.25° (range -3.0° to +2.0°). When navigation is used only to guide the positioning of the cutting jig, errors may arise in the manual, non-navigated steps of the procedure. Our study showed increased cutting errors in the sagittal plane for both the femur and the tibia, and following implantation, the greatest error was seen in the sagittal alignment of the tibial component. Computer navigation should be used not only to guide the positioning of the cutting jig, but also to check the bone resection and implant position during TKA. IV.

Observational and Model Analysis of a Two-ribbon Flare Possibly Induced by a Neighboring Blowout Jet

NASA Astrophysics Data System (ADS)

Joshi, Bhuwan; Thalmann, Julia K.; Mitra, Prabir K.; Chandra, Ramesh; Veronig, Astrid M.

2017-12-01

In this paper, we present unique observations of a blowout coronal jet that possibly triggered a two-ribbon confined C1.2 flare in bipolar solar active region NOAA 12615 on 2016 December 5. The jet activity initiates at chromospheric/transition region heights with a small brightening that eventually increases in volume, with well-developed standard morphological jet features, viz., base and spire. The spire widens up with a collimated eruption of cool and hot plasma components, observed in the 304 and 94 Å channels of AIA, respectively. The speed of the plasma ejection, which forms the jet’s spire, was higher for the hot component (˜200 km s-1) than the cooler one (˜130 km s-1). The NLFF model of coronal fields at the pre- and post-jet phases successfully reveals openings of previously closed magnetic field lines with a rather inclined/low-lying jet structure. The peak phase of the jet emission is followed by the development of a two-ribbon flare that shows coronal loop emission in HXRs up to ˜25 keV energy. The coronal magnetic fields rooted at the location of EUV flare ribbons, derived from the NLFF model, demonstrate the pre-flare phase to exhibit an “X-type” configuration, while the magnetic fields at the post-flare phase are more or less oriented parallel. Comparisons of multi-wavelength measurements with the magnetic field extrapolations suggest that the jet activity likely triggered the two-ribbon flare by perturbing the field in the interior of the active region.

Solar wind classification from a machine learning perspective

NASA Astrophysics Data System (ADS)

Heidrich-Meisner, V.; Wimmer-Schweingruber, R. F.

2017-12-01

It is a very well known fact that the ubiquitous solar wind comes in at least two varieties, the slow solar wind and the coronal hole wind. The simplified view of two solar wind types has been frequently challenged. Existing solar wind categorization schemes rely mainly on different combinations of the solar wind proton speed, the O and C charge state ratios, the Alfvén speed, the expected proton temperature and the specific proton entropy. In available solar wind classification schemes, solar wind from stream interaction regimes is often considered either as coronal hole wind or slow solar wind, although their plasma properties are different compared to "pure" coronal hole or slow solar wind. As shown in Neugebauer et al. (2016), even if only two solar wind types are assumed, available solar wind categorization schemes differ considerably for intermediate solar wind speeds. Thus, the decision boundary between the coronal hole and the slow solar wind is so far not well defined.In this situation, a machine learning approach to solar wind classification can provide an additional perspective.We apply a well-known machine learning method, k-means, to the task of solar wind classification in order to answer the following questions: (1) How many solar wind types can reliably be identified in our data set comprised of ten years of solar wind observations from the Advanced Composition Explorer (ACE)? (2) Which combinations of solar wind parameters are particularly useful for solar wind classification?Potential subtypes of slow solar wind are of particular interest because they can provide hints of respective different source regions or release mechanisms of slow solar wind.

Push-out bond strengths of fiber-reinforced composite posts with various resin cements according to the root level

PubMed Central

Chang, Hoon-Sang; Noh, Young-Sin; Lee, Yoon; Min, Kyung-San

2013-01-01

PURPOSE The aim of this study was to determine whether the push-out bond strengths between the radicular dentin and fiber reinforced-composite (FRC) posts with various resin cements decreased or not, according to the coronal, middle or apical level of the root. MATERIALS AND METHODS FRC posts were cemented with one of five resin cement groups (RelyX Unicem: Uni, Contax with activator & LuxaCore-Dual: LuA, Contax & LuxaCore-Dual: Lu, Panavia F 2.0: PA, Super-Bond C&B: SB) into extracted human mandibular premolars. The roots were sliced into discs at the coronal, middle and apical levels. Push-out bond strength tests were performed with a universal testing machine at a crosshead speed of 0.5 mm/min, and the failure aspect was analyzed. RESULTS There were no significant differences (P>.05) in the bond strengths of the different resin cements at the coronal level, but there were significant differences in the bond strengths at the middle and apical levels (P<.05). Only the Uni and LuA cements did not show any significant decrease in their bond strengths at all the root levels (P>.05); all other groups had a significant decrease in bond strength at the middle or apical level (P<.05). The failure aspect was dominantly cohesive at the coronal level of all resin cements (P<.05), whereas it was dominantly adhesive at the apical level. CONCLUSION All resin cement groups showed decreases in bond strengths at the middle or apical level except LuA and Uni. PMID:24049569

Neutral-Line Magnetic Shear and Enhanced Coronal Heating in Solar Active Regions

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Gary, G. A.; Shimizu, T.

1997-01-01

By examining the magnetic structure at sites in the bright coronal interiors of active regions that are not flaring but exhibit persistent strong coronal heating, we establish some new characteristics of the magnetic origins of this heating. We have examined the magnetic structure of these sites in five active regions, each of which was well observed by both the Yohkoh SXT and the Marshall Space Flight Center Vector Magnetograph and showed strong shear in its magnetic field along part of at least one neutral line (polarity inversion). Thus, we can assess whether this form of nonpotential field structure in active regions is a characteristic of the enhanced coronal heating and vice versa. From 27 orbits' worth of Yohkoh SXT images of the five active regions, we have obtained a sample of 94 persistently bright coronal features (bright in all images from a given orbit), 40 long (greater than or approximately equals 20,000 km) neutral-line segments having strong magnetic shear throughout (shear angle greater than 45 deg), and 39 long neutral-line segments having weak magnetic shear throughout (shear angle less than 45 deg). From this sample, we find that: (1) all of our persistently bright coronal features are rooted in magnetic fields that are stronger than 150 G; (2) nearly all (95%) of these enhanced coronal features are rooted near neutral lines (closer than 10,000 km); (3) a great majority (80%) of the bright features are rooted near strong-shear portions of neutral lines; (4) a great majority (85%) of long strong-shear segments of neutral lines have persistently bright coronal features rooted near them; (5) a large minority (40%) of long weak-shear segments of neutral lines have persistently bright coronal features rooted near them; and (6) the brightness of a persistently bright Coronal feature often changes greatly over a few hours. From these results, we conclude that most persistent enhanced heating of coronal loops in active regions: (1) requires the presence of a polarity inversion in the magnetic field near at least one of the loop footpoints; (2) is greatly aided by the presence of strong shear in the core magnetic field along that neutral line; and (3) is controlled by some variable process that acts in this magnetic environment. We infer that this variable process is low-lying reconnection accompanying flux cancellation.

Coronal Magnetism: Hanle Effect in UV and IR Spectral Lines

NASA Astrophysics Data System (ADS)

Raouafi, N. E.; Riley, P.

2014-12-01

The plasma thermodynamics in the solar upper atmosphere, particularly in the corona, are dominated by the magnetic field, which controls the flow and dissipation of energy. The relative lack of knowledge of the coronal vector magnetic field is a major handicap for the progress in coronal physics. This makes the development of measurement methods of coronal magnetic fields a high priority in solar physics. The Hanle effect in the UV and IR spectral lines is a largely unexplored diagnostic. Here we use magnetohydrodynamic (MHD) simulations to study the magnitude of the signal to be expected for typical coronal magnetic fields for selected spectral lines in the UV and IR wavelength ranges, namely the H I Lyman series (i.e., α, β, and γ), O VI 103.2 nm line, and the He I 1083 nm line. We show that the selected lines may be useful for the diagnostic of coronal magnetic fields. We also show that the combination of polarization measurements of spectral lines with different sensitivities to the Hanle effect may be most appropriate for the interpretation of the data. We propose that UV coronal magnetic field mapper should be a central part of the science payload of any future spacebased solar observatory.

Effect of coronal flaring on apical extrusion of debris during root canal instrumentation using single-file systems.

PubMed

Topçuoğlu, H S; Üstün, Y; Akpek, F; Aktı, A; Topçuoğlu, G

2016-09-01

To evaluate the effect of coronal flaring on the amount of debris extruded apically during root canal preparation using the Reciproc, WaveOne (WO) and OneShape (OS) single-file systems. Ninety extracted single-rooted mandibular incisor teeth were randomly assigned to six groups (n = 15 for each group) for canal instrumentation. Endodontic access cavities were prepared in each tooth. In three of the six groups, coronal flaring was not performed; coronal flaring was performed with Gates-Glidden drills on all teeth in the remaining three groups. The canals were then instrumented with one or other of the following single-file instrument systems: Reciproc, WO and OS. Debris extruded apically during instrumentation was collected into pre-weighed Eppendorf tubes. The tubes were then stored in an incubator at 70 °C for 5 days. The weight of the dry extruded debris was established by subtracting the pre-instrumentation and post-instrumentation weight of the Eppendorf tubes for each group. Data were analysed using one-way analysis of variance (anova) and Tukey's post hoc tests (P = 0.05). Reciproc and WO files without coronal flaring produced significantly more debris compared with the other groups (P < 0.05). There was no significant difference in apical extrusion of debris amongst the other groups (P > 0.05). All single-file systems caused apical extrusion of debris. Performing coronal flaring prior to canal preparation reduced the amount of apically extruded debris when using Reciproc or WO systems. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Thermosphere Global Time Response to Geomagnetic Storms Caused by Coronal Mass Ejections

NASA Astrophysics Data System (ADS)

Oliveira, D. M.; Zesta, E.; Schuck, P. W.; Sutton, E. K.

2017-10-01

We investigate, for the first time with a spatial superposed epoch analysis study, the thermosphere global time response to 159 geomagnetic storms caused by coronal mass ejections (CMEs) observed in the solar wind at Earth's orbit during the period of September 2001 to September 2011. The thermosphere neutral mass density is obtained from the CHAMP (CHAllenge Mini-Satellite Payload) and GRACE (Gravity Recovery Climate Experiment) spacecraft. All density measurements are intercalibrated against densities computed by the Jacchia-Bowman 2008 empirical model under the regime of very low geomagnetic activity. We explore both the effects of the pre-CME shock impact on the thermosphere and of the storm main phase onset by taking their times of occurrence as zero epoch times (CME impact and interplanetary magnetic field Bz southward turning) for each storm. We find that the shock impact produces quick and transient responses at the two high-latitude regions with minimal propagation toward lower latitudes. In both cases, thermosphere is heated in very high latitude regions within several minutes. The Bz southward turning of the storm onset has a fast heating manifestation at the two high-latitude regions, and it takes approximately 3 h for that heating to propagate down to equatorial latitudes and to globalize in the thermosphere. This heating propagation is presumably accomplished, at least in part, with traveling atmospheric disturbances and complex meridional wind structures. Current models use longer lag times in computing thermosphere density dynamics during storms. Our results suggest that the thermosphere response time scales are shorter and should be accordingly adjusted in thermospheric empirical models.

Structure and Dynamics of Coronal Plasmas

NASA Technical Reports Server (NTRS)

Golub, Leon

1997-01-01

During the past year this grant has funded research in the interaction between magnetic fields and the hot plasma in the solar outer atmosphere. The following is a brief summary of the published papers, abstracts and talks which have been supported. The paper 'Coronal Structures Observed in X-rays and H-alpha Structures' was published in the Kofu Symposium proceedings. The study analyzes cool and hot behavior of two x-ray events, a small flare and a surge. We find that a large H-alpha surge appears in x-rays as a very weak event, while a weak H-alpha feature corresponds to the brightest x-ray emission on the disk at the time of the observation. Calculations of the heating necessary to produce these signatures, and implications for the driving and heating mechanisms of flares vs. surges are presented. A copy of the paper is appended to this report. The paper 'Differential Magnetic Field Shear in an Active Region' has been published in The Astrophysical Journal. We have compared the 3D extrapolation of magnetic fields with the observed coronal structure in an active region. Based on the fit between observed coronal structure throughout the volume of the region and the calculated magnetic field configurations, we propose a differential magnetic field shear model for this active region. The decreasing field shear in the outer portions of the AR may indicate a continual relaxation of the magnetic field with time, corresponding to a net transport of helicity outward. The paper 'Difficulties in Observing Coronal Structure' has been accepted for publication in the journal Solar Physics. In this paper we discuss the evidence that the temperature and density structure of the corona are far more complicated than had previously been thought. The discussion is based on five studies carried out by our group on coronal plasma properties, showing that any one x-ray instrument does see all of the plasma present in the corona, that hot and cool material may appear to be co-spatial at a given location in the corona, and that simple magnetic field extrapolations provide only a poor fit to the observed structure. A copy of the paper is appended to this report.

Probing the solar corona with very long baseline interferometry.

PubMed

Soja, B; Heinkelmann, R; Schuh, H

2014-06-20

Understanding and monitoring the solar corona and solar wind is important for many applications like telecommunications or geomagnetic studies. Coronal electron density models have been derived by various techniques over the last 45 years, principally by analysing the effect of the corona on spacecraft tracking. Here we show that recent observational data from very long baseline interferometry (VLBI), a radio technique crucial for astrophysics and geodesy, could be used to develop electron density models of the Sun's corona. The VLBI results agree well with previous models from spacecraft measurements. They also show that the simple spherical electron density model is violated by regional density variations and that on average the electron density in active regions is about three times that of low-density regions. Unlike spacecraft tracking, a VLBI campaign would be possible on a regular basis and would provide highly resolved spatial-temporal samplings over a complete solar cycle.

A Concept for Measuring Electron Distribution Functions Using Collective Thomson Scattering

NASA Astrophysics Data System (ADS)

Milder, A. L.; Froula, D. H.

2017-10-01

A.B. Langdon proposed that stable non-Maxwellian distribution functions are realized in coronal inertial confinement fusion plasmas via inverse bremsstrahlung heating. For Zvosc2 Zvosc2 vth2 > 1 , vth2 > 1 , the inverse bremsstrahlung heating rate is sufficiently fast to compete with electron-electron collisions. This process preferentially heats the subthermal electrons leading to super-Gaussian distribution functions. A method to identify the super-Gaussian order of the distribution functions in these plasmas using collective Thomson scattering will be proposed. By measuring the collective Thomson spectra over a range of angles the density, temperature and super-Gaussian order can be determined. This is accomplished by fitting non-Maxwellian distribution data with a super-Gaussian model; in order to match the density and electron temperature to within 10%, the super-Gaussian order must be varied. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Recurring coronal holes and their rotation rates during the solar cycles 22-24

NASA Astrophysics Data System (ADS)

Prabhu, K.; Ravindra, B.; Hegde, Manjunath; Doddamani, Vijayakumar H.

2018-05-01

Coronal holes (CHs) play a significant role in making the Earth geo-magnetically active during the declining and minimum phases of the solar cycle. In this study, we analysed the evolutionary characteristics of the Recurring CHs from the year 1992 to 2016. The extended minimum of Solar Cycle 23 shows unusual characteristics in the number of persistent coronal holes in the mid- and low-latitude regions of the Sun. Carrington rotation maps of He 10830 Å and EUV 195 Å observations are used to identify the Coronal holes. The latitude distribution of the RCHs shows that most of them are appeared between ± 20° latitudes. In this period, more number of recurring coronal holes appeared in and around 100° and 200° Carrington longitudes. The large sized coronal holes lived for shorter period and they appeared close to the equator. From the area distribution over the latitude considered, it shows that more number of recurring coronal holes with area <10^{21} cm2 appeared in the southern latitude close to the equator. The rotation rates calculated from the RCHs appeared between ± 60° latitude shows rigid body characteristics. The derived rotational profiles of the coronal holes show that they have anchored to a depth well below the tachocline of the interior, and compares well with the helioseismology results.

Observations and Numerical Models of Solar Coronal Heating Associated with Spicules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pontieu, B. De; Martinez-Sykora, J.; Moortel, I. De

Spicules have been proposed as significant contributors to the mass and energy balance of the corona. While previous observations have provided a glimpse of short-lived transient brightenings in the corona that are associated with spicules, these observations have been contested and are the subject of a vigorous debate both on the modeling and the observational side. Therefore, it remains unclear whether plasma is heated to coronal temperatures in association with spicules. We use high-resolution observations of the chromosphere and transition region (TR) with the Interface Region Imaging Spectrograph and of the corona with the Atmospheric Imaging Assembly on board themore » Solar Dynamics Observatory to show evidence of the formation of coronal structures associated with spicular mass ejections and heating of plasma to TR and coronal temperatures. Our observations suggest that a significant fraction of the highly dynamic loop fan environment associated with plage regions may be the result of the formation of such new coronal strands, a process that previously had been interpreted as the propagation of transient propagating coronal disturbances. Our observations are supported by 2.5D radiative MHD simulations that show heating to coronal temperatures in association with spicules. Our results suggest that heating and strong flows play an important role in maintaining the substructure of loop fans, in addition to the waves that permeate this low coronal environment.« less

A Self-consistent Model of the Coronal Heating and Solar Wind Acceleration Including Compressible and Incompressible Heating Processes

NASA Astrophysics Data System (ADS)

Shoda, Munehito; Yokoyama, Takaaki; Suzuki, Takeru K.

2018-02-01

We propose a novel one-dimensional model that includes both shock and turbulence heating and qualify how these processes contribute to heating the corona and driving the solar wind. Compressible MHD simulations allow us to automatically consider shock formation and dissipation, while turbulent dissipation is modeled via a one-point closure based on Alfvén wave turbulence. Numerical simulations were conducted with different photospheric perpendicular correlation lengths {λ }0, which is a critical parameter of Alfvén wave turbulence, and different root-mean-square photospheric transverse-wave amplitudes δ {v}0. For the various {λ }0, we obtain a low-temperature chromosphere, high-temperature corona, and supersonic solar wind. Our analysis shows that turbulence heating is always dominant when {λ }0≲ 1 {Mm}. This result does not mean that we can ignore the compressibility because the analysis indicates that the compressible waves and their associated density fluctuations enhance the Alfvén wave reflection and therefore the turbulence heating. The density fluctuation and the cross-helicity are strongly affected by {λ }0, while the coronal temperature and mass-loss rate depend weakly on {λ }0.

EFFECT OF A SAUSAGE OSCILLATION ON RADIO ZEBRA-PATTERN STRUCTURES IN A SOLAR FLARE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sijie; Yan, Yihua; Nakariakov, V. M., E-mail: sjyu@nao.cas.cn

2016-07-20

Sausage modes that are axisymmetric fast magnetoacoustic oscillations of solar coronal loops are characterized by variation of the plasma density and magnetic field, and hence cause time variations of the electron plasma frequency and cyclotron frequency. The latter parameters determine the condition for the double plasma resonance (DPR), which is responsible for the appearance of zebra-pattern (ZP) structures in time spectra of solar type IV radio bursts. We perform numerical simulations of standing and propagating sausage oscillations in a coronal loop modeled as a straight, field-aligned plasma slab, and determine the time variation of the DPR layer locations. Instant valuesmore » of the plasma density and magnetic field at the DPR layers allowed us to construct skeletons of the time variation of ZP stripes in radio spectra. In the presence of a sausage oscillation, the ZP structures are shown to have characteristic wiggles with the time period prescribed by the sausage oscillation. Standing and propagating sausage oscillations are found to have different signatures in ZP patterns. We conclude that ZP wiggles can be used for the detection of short-period sausage oscillations and the exploitation of their seismological potential.« less

Characteristics of Kinematics of a Coronal Mass Ejection During the 2010 August 1 CME-CME Interaction Event

NASA Technical Reports Server (NTRS)

Temmer, Manuela; Vrsnak, Bojan; Rollett, Tanja; Bein, Bianca; de Koning, Curt A.; Liu, Ying; Bosman, Eckhard; Davies, Jackie A.; Mostl, Christian; Zic, Tomislav;

Coronal loop seismology using damping of standing kink oscillations by mode coupling. II. additional physical effects and Bayesian analysis

NASA Astrophysics Data System (ADS)

Pascoe, D. J.; Anfinogentov, S.; Nisticò, G.; Goddard, C. R.; Nakariakov, V. M.

2017-04-01

Context. The strong damping of kink oscillations of coronal loops can be explained by mode coupling. The damping envelope depends on the transverse density profile of the loop. Observational measurements of the damping envelope have been used to determine the transverse loop structure which is important for understanding other physical processes such as heating. Aims: The general damping envelope describing the mode coupling of kink waves consists of a Gaussian damping regime followed by an exponential damping regime. Recent observational detection of these damping regimes has been employed as a seismological tool. We extend the description of the damping behaviour to account for additional physical effects, namely a time-dependent period of oscillation, the presence of additional longitudinal harmonics, and the decayless regime of standing kink oscillations. Methods: We examine four examples of standing kink oscillations observed by the Atmospheric Imaging Assembly (AIA) onboard the Solar Dynamics Observatory (SDO). We use forward modelling of the loop position and investigate the dependence on the model parameters using Bayesian inference and Markov chain Monte Carlo (MCMC) sampling. Results: Our improvements to the physical model combined with the use of Bayesian inference and MCMC produce improved estimates of model parameters and their uncertainties. Calculation of the Bayes factor also allows us to compare the suitability of different physical models. We also use a new method based on spline interpolation of the zeroes of the oscillation to accurately describe the background trend of the oscillating loop. Conclusions: This powerful and robust method allows for accurate seismology of coronal loops, in particular the transverse density profile, and potentially reveals additional physical effects.

A GLOBAL VIEW OF VELOCITY FLUCTUATIONS IN THE CORONA BELOW 1.3 R {sub ⊙} WITH CoMP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morton, R. J.; Tomczyk, S.; Pinto, R. F., E-mail: richard.morton@northumbria.ac.uk

The Coronal Multi-channel Polarimeter (CoMP) has previously demonstrated the presence of Doppler velocity fluctuations in the solar corona. The observed fluctuations are thought to be transverse waves, i.e., highly incompressible motions whose restoring force is dominated by the magnetic tension, some of which demonstrate clear periodicity. We aim to exploit CoMP’s ability to provide high cadence observations of the off-limb corona to investigate the properties of velocity fluctuations in a range of coronal features, providing insight into how (whether) the properties of the waves are influenced by the varying magnetic topology in active regions, quiet Sun and open field regions.more » An analysis of Doppler velocity time-series of the solar corona from the 10747 Å Iron xiii line is performed, determining the velocity power spectrum and using it as a tool to probe wave behavior. Further, the average phase speed and density for each region are estimated and used to compute the spectra for energy density and energy flux. In addition, we assess the noise levels associated with the CoMP data, deriving analytic formulae for the uncertainty on Doppler velocity measurements and providing a comparison by estimating the noise from the data. It is found that the entire corona is replete with transverse wave behavior. The corresponding power spectra indicate that the observed velocity fluctuations are predominately generated by stochastic processes, with the spectral slope of the power varying between the different magnetic regions. Most strikingly, all power spectra reveal the presence of enhanced power occurring at ∼3 mHz, potentially implying that the excitation of coronal transverse waves by p -modes is a global phenomenon.« less

Clinical Evaluation of positioning verification using digital tomosynthesis (DTS) based on bony anatomy and soft tissues for prostate image-guided radiation therapy (IGRT)

PubMed Central

Yoo, Sua; Wu, Q. Jackie; Godfrey, Devon; Yan, Hui; Ren, Lei; Das, Shiva; Lee, William R.; Yin, Fang-Fang

2008-01-01

Purpose To evaluate on-board digital tomosynthesis (DTS) for patient positioning in comparison with 2D-radiographs and 3D-CBCT. Methods and Materials A total of 92 image sessions from 9 prostate cancer patients were analyzed. An on-board image set was registered to a corresponding reference image set. Four pairs of image sets were used; DRR vs. on-board orthogonal paired radiograph for the 2D method, coronal-reference-DTS (RDTS) vs. on-board coronal-DTS for the coronal-DTS method, sagittal-RDTS vs. on-board sagittal-DTS for the sagittal-DTS method, and planning CT vs. CBCT for the CBCT method. Registration results were compared. Results The systematic errors in all methods were less than 1 mm/1°. When registering bony anatomy, the mean vector differences were 0.21±0.11 cm between 2D and CBCT, 0.11±0.08 cm between CBCT and coronal-DTS, and 0.14±0.07 cm between CBCT and sagittal-DTS. The correlation of CBCT to DTS was stronger (coefficients=0.92–0.95) than the correlation between 2D and CBCT or DTS (coefficients=0.81–0.83). When registering soft tissue, the mean vector differences were 0.18±0.11 cm between CBCT and coronal-DTS and 0.29±0.17 cm between CBCT and sagittal-DTS. The correlation coefficients of CBCT to sagittal-DTS and to coronal-DTS were 0.84 and 0.92, respectively. Conclusions DTS could provide equivalent results to CBCT when bony anatomy is used as landmarks for prostate IGRT. For soft tissue-based positioning verification, coronal-DTS produced equivalent results to CBCT and sagittal-DTS alone was insufficient. DTS could allow comparable soft tissue-based target localization with faster scanning time and less imaging dose compared to CBCT. PMID:19100923

Interaction of Solar-Flare-Accelerated Nuclei with the Solar Photosphere and the Isotopic Composition of the Solar Wind

NASA Astrophysics Data System (ADS)

Vasil'ev, G. I.; Ostryakov, V. M.; Pavlov, A. K.; Chakchurina, M. E.

2017-12-01

The nuclear interactions of solar-flare-accelerated protons and ions with the solar atmosphere and the deeper layers of the Sun lead to the formation of several stable and radioactive isotopes. This article examines the GEANT4 depth profiles of 2H, 3H, 3He, 6Li, 7Li, 10Be, and 14C. When accelerated particles pass through a layer of 0.1-2 g cm-2, 6Li, 7Li, 10Be, and 14C isotopes form in sufficient amounts to explain their anomalous abundances in lunar soil samples. It is assumed that they escape into interplanetary space with coronal mass ejections immediately after the flare.

Effect of two fiber post types and two luting cement systems on regional post retention using the push-out test.

PubMed

Wang, Vivian J-J; Chen, Ya-Ming; Yip, Kevin H-K; Smales, Roger J; Meng, Qing-Fei; Chen, Lijuan

2008-03-01

To investigate regional root canal push-out bond strengths for two fiber-reinforced post types using two adhesive systems. The crowns of 24 recently extracted sound maxillary central incisors were sectioned transversely 2 mm coronal to the labial cemento-enamel junction, and the roots treated endodontically. Following standardized post space preparations, fiber-reinforced posts (C-POST; AESTHETI-PLUS) were placed using two adhesive systems (acid-etch ONE-STEP PLUS/C&B CEMENT; self-adhesive RelyX Unicem), in four equal groups. Push-out bond strength tests were performed at four sites in each root. Results were analyzed using split-plot ANOVA, with a=0.05 for statistical significance. AESTHETI-PLUS quartz fiber-reinforced posts showed significantly higher push-out strengths than C-POST carbon fiber-reinforced posts (P<0.0001). The separate acid-etch adhesive system resulted in significantly higher bond strengths than the self-etch self-adhesive system (P<0.0001). Bond strengths decreased significantly from coronal to apical root canal regions (P<0.0001). The quartz fiber-reinforced post placed using the separate acid-etch adhesive system provided significantly better post retention than the carbon fiber-reinforced post placed using the self-etch self-adhesive system.

Observational Features of Equatorial Coronal Hole Jets

DTIC Science & Technology

2010-02-10

0 “Esplorazione del Sistema Solare ”. Some images are produced by FESTIVAL, collaborative project managed by IAS and supported by CNES, which is a...km s−1, while the deceleration rate appears to be about 0.11 km s−2, less than solar gravity. The average jet visibility time is about 30 minutes...differences between polar and equatorial coronal hole jets. Keywords. Coronal holes, jets 1 Introduction The STEREO ( Solar TErrestrial RElations

SU-E-I-10: Investigation On Detectability of a Small Target for Different Slice Direction of a Volumetric Cone Beam CT Image

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C; Han, M; Baek, J

Purpose: To investigate the detectability of a small target for different slice direction of a volumetric cone beam CT image and its impact on dose reduction. Methods: Analytic projection data of a sphere object (1 mm diameter, 0.2/cm attenuation coefficient) were generated and reconstructed by FDK algorithm. In this work, we compared the detectability of the small target from four different backprojection Methods: hanning weighted ramp filter with linear interpolation (RECON 1), hanning weighted ramp filter with Fourier interpolation (RECON2), ramp filter with linear interpolation (RECON 3), and ramp filter with Fourier interpolation (RECON4), respectively. For noise simulation, 200 photonsmore » per measurement were used, and the noise only data were reconstructed using FDK algorithm. For each reconstructed volume, axial and coronal slice were extracted and detection-SNR was calculated using channelized Hotelling observer (CHO) with dense difference-of-Gaussian (D-DOG) channels. Results: Detection-SNR of coronal images varies for different backprojection methods, while axial images have a similar detection-SNR. Detection-SNR{sup 2} ratios of coronal and axial images in RECON1 and RECON2 are 1.33 and 1.15, implying that the coronal image has a better detectability than axial image. In other words, using coronal slices for the small target detection can reduce the patient dose about 33% and 15% compared to using axial slices in RECON 1 and RECON 2. Conclusion: In this work, we investigated slice direction dependent detectability of a volumetric cone beam CT image. RECON 1 and RECON 2 produced the highest detection-SNR, with better detectability in coronal slices. These results indicate that it is more beneficial to use coronal slice to improve detectability of a small target in a volumetric cone beam CT image. This research was supported by the MSIP (Ministry of Science, ICT and Future Planning), Korea, under the IT Consilience Creative Program (NIPA-2014-H0201-14-1002) supervised by the NIPA (National IT Industry Promotion Agency). Authors declares that s/he has no conflict of Interest in relation to the work in this abstract.« less

The interpretation of simultaneous soft X-ray spectroscopic and imaging observations of an active region. [in solar corona

NASA Technical Reports Server (NTRS)

Davis, J. M.; Gerassimenko, M.; Krieger, A. S.; Vaiana, G. S.

1975-01-01

Simultaneous soft X-ray spectroscopic and broad-band imaging observations of an active region have been analyzed together to determine the parameters which describe the coronal plasma. From the spectroscopic data, models of temperature-emission measure-elemental abundance have been constructed which provide acceptable statistical fits. By folding these possible models through the imaging analysis, models which are not self-consistent can be rejected. In this way, only the oxygen, neon, and iron abundances of Pottasch (1967), combined with either an isothermal or exponential temperature-emission-measure model, are consistent with both sets of data. Contour maps of electron temperature and density for the active region have been constructed from the imaging data. The implications of the analysis for the determination of coronal abundances and for future satellite experiments are discussed.

The evolution of a coronal streamer and the photospheric magnetic field

NASA Technical Reports Server (NTRS)

Poland, A. I.; Macqueen, R. M.

1981-01-01

A large equatorial coronal streamer observed in the outer corona grew in brightness and size during successive limb passages between October 6, 1973 and January 10, 1974 (solar rotations 1606-1611). Unlike previous studies of streamers and their photospheric associations, no definite surface feature could be identified in the present case. This suggests that the streamer is associated with the large scale photospheric magnetic field. Comparison of the streamer growth with observed underlying photospheric magnetic flux changes indicated that as the streamer increased in brightness, areal extent, and density, the photospheric magnetic flux decreased. Three possible explanations for the streamer's growth are presented, the conceptually simplest being that the decrease in photospheric field results in an opening of the flux tubes under the streamer, which permits an increase mass flux through the streamer.

A magnetohydrodynamic theory of coronal loop transients

NASA Technical Reports Server (NTRS)

Yeh, T.

1982-01-01

The physical and geometrical characteristics of solar coronal loop transients are described in an MHD model based on Archimedes' MHD buoyancy force. The theory was developed from interpretation of coronagraphic data, particularly from Skylab. The brightness of a loop is taken to indicate the electron density, and successive pictures reveal the electron enhancement in different columns. The forces which lift the loop off the sun surface are analyzed as an MHD buoyancy force affecting every mass element by imparting an inertial force necessary for heliocentrifugal motion. Thermal forces are responsible for transferring the ambient stress to the interior of the loop to begin the process. The kinematic and hydrostatic buoyancy overcome the gravitational force, and a flux rope can then curve upward, spiralling like a corkscrew with varying cross section around the unwinding solar magnetic field lines.

Apert Syndrome: Molecularly Confirmed C.758C>G (P.Pro253Arg) in FGFR2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cha Gon, Lee, E-mail: leechagon@eulji.ac.kr

A 5-day-old girl was referred to our clinic for evaluation of congenital malformations. She was identified with a pathogenic mutation c.758C>G (p.Pro253Arg) in FGFR2 gene using targeted exome sequencing. The de novo mutation was confirmed with Sanger sequencing in the patient and her parents. She showed occipital plagiocephaly with frontal bossing (Figure A and B). Skull frontal and lateral radiography revealed fusion of most of the sutures except coronal suture, with convolutional markings (Figure D and E). She had complete cleft palate (Figure C). Her fused bilateral hands showed type II syndactyly with complete syndactyly between the ring and themore » little fingers (Figure F1-F3). Both toes were simple syndactyly with side-to-side fusion of skin (Figure G1-)« less

A Doppler dimming determination of coronal outflow velocity

NASA Technical Reports Server (NTRS)

Strachan, Leonard; Kohl, John L.; Weiser, Heinz; Withbroe, George L.; Munro, Richard H.

1993-01-01

Outflow velocities in a polar coronal hole are derived from observations made during a 1982 sounding rocket flight. The velocity results are derived from a Doppler dimming analysis of resonantly scattered H I Ly-alpha. This analysis indicates radial outflow velocities of 217 km/s at 2 solar radii from sun-center with an uncertainty range of 153 to 251 km/s at a confidence level of 67 percent. These results are best characterized as strong evidence for supersonic outflow within 2 solar radii of sun-center in a polar coronal hole. Several means for obtaining improved accuracy in future observations are discussed.

Cybersickness Onset With Reflexive Head Movements During Land and Shipboard Head-Mounted Display Flight Simulation

DTIC Science & Technology

2010-09-09

provoked a predictable OKCR coronal head tilt (p < 0.001) whenever aircraft angle of bank (AOB) increased (Fig. 2). With 90º of simulated AOB, land... head pitch were –3.3 ± 3.8 to 6.8 ± 5.9 on land, and –4.0º ± 5.6 to 7.6º ± 9.7 at sea (Fig. 3). 7 Combined Coronal OKCR ( Head Tilt ) Data for...Land OKCR Figure 2: Coronal OKCR ( head tilt ) vs. angle of bank, during both land based and shipboard HMD/VR flight simulation. Combined

Coherent structure in solar wind C{sup 6+}/C{sup 4+} ionic composition data during the quiet-sun conditions of 2008

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edmondson, J. K.; Lepri, S. T.; Zurbuchen, T. H.

2013-11-20

This analysis offers evidence of characteristic scale sizes in solar wind charge state data measured in situ for 13 quiet-Sun Carrington rotations in 2008. Using a previously established novel methodology, we analyze the wavelet power spectrum of the charge state ratio C{sup 6+}/C{sup 4+} measured in situ by ACE/SWICS for 2 hr and 12 minute cadence. We construct a statistical significance level in the wavelet power spectrum to quantify the interference effects arising from filling missing data in the time series, allowing extraction of significant power from the measured data to a resolution of 24 minutes. We analyze each waveletmore » power spectrum for transient coherency and global periodicities resulting from the superposition of repeating coherent structures. From the significant wavelet power spectra, we find evidence for a general upper limit on individual transient coherency of ∼10 days. We find evidence for a set of global periodicities between 4-5 hr and 35-45 days. We find evidence for the distribution of individual transient coherency scales consisting of two distinct populations. Below the ∼2 day timescale, the distribution is reasonably approximated by an inverse power law, whereas for scales ≳2 days, the distribution levels off, showing discrete peaks at common coherency scales. In addition, by organizing the transient coherency scale distributions by wind type, we find that these larger, common coherency scales are more prevalent and well defined in coronal hole wind. Finally, we discuss the implications of our results for current theories of solar wind generation and describe future work for determining the relationship between the coherent structures in our ionic composition data and the structure of the coronal magnetic field.« less

Radio Remote Sensing of Coronal Mass Ejections: Implications for Parker Solar Probe and Solar Orbiter

NASA Astrophysics Data System (ADS)

Kooi, J. E.; Thomas, N. C.; Guy, M. B., III; Spangler, S. R.

2017-12-01

Coronal mass ejections (CMEs) are fast-moving magnetic field structures of enhanced plasma density that play an important role in space weather. The Solar Orbiter and Parker Solar Probe will usher in a new era of in situ measurements, probing CMEs within distances of 60 and 10 solar radii, respectively. At the present, only remote-sensing techniques such as Faraday rotation can probe the plasma structure of CMEs at these distances. Faraday rotation is the change in polarization position angle of linearly polarized radiation as it propagates through a magnetized plasma (e.g. a CME) and is proportional to the path integral of the electron density and line-of-sight magnetic field. In conjunction with white-light coronagraph measurements, Faraday rotation observations have been used in recent years to determine the magnetic field strength of CMEs. We report recent results from simultaneous white-light and radio observations made of a CME in July 2015. We made radio observations using the Karl G. Jansky Very Large Array (VLA) at 1 - 2 GHz frequencies of a set of radio sources through the solar corona at heliocentric distances that ranged between 8 - 23 solar radii. These Faraday rotation observations provide a priori estimates for comparison with future in situ measurements made by the Solar Orbiter and Parker Solar Probe. Similar Faraday rotation observations made simultaneously with observations by the Solar Orbiter and Parker Solar Probe in the future could provide information about the global structure of CMEs sampled by these probes and, therefore, aid in understanding the in situ measurements.

Diagnostics of the solar corona from comparison between Faraday rotation measurements and magnetohydrodynamic simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Chat, G.; Cohen, O.; Kasper, J. C.

Polarized natural radio sources passing behind the Sun experience Faraday rotation as a consequence of the electron density and magnetic field strength in coronal plasma. Since Faraday rotation is proportional to the product of the density and the component of the magnetic field along the line of sight of the observer, a model is required to interpret the observations and infer coronal structures. Faraday rotation observations have been compared with relatively ad hoc models of the corona. Here for the first time we compare these observations with magnetohydrodynamic (MHD) models of the solar corona driven by measurements of the photosphericmore » magnetic field. We use observations made with the NRAO Very Large Array of 34 polarized radio sources occulted by the solar corona between 5 and 14 solar radii. The measurements were made during 1997 May, and 2005 March and April. We compare the observed Faraday rotation values with values extracted from MHD steady-state simulations of the solar corona. We find that (1) using a synoptic map of the solar magnetic field just one Carrington rotation off produces poorer agreements, meaning that the outer corona changes in the course of one month, even in solar minimum; (2) global MHD models of the solar corona driven by photospheric magnetic field measurements are generally able to reproduce Faraday rotation observations; and (3) some sources show significant disagreement between the model and the observations, which appears to be a function of the proximity of the line of sight to the large-scale heliospheric current sheet.« less

Relationship of EUV Irradiance Coronal Dimming Slope and Depth to Coronal Mass Ejection Speed and Mass

NASA Technical Reports Server (NTRS)

Mason, James Paul; Woods, Thomas N.; Webb, David F.; Thompson, Barbara J.; Colaninno, Robin C.; Vourlidas, Angelos

2016-01-01

Extreme ultraviolet (EUV) coronal dimmings are often observed in response to solar eruptive events. These phenomena can be generated via several different physical processes. For space weather, the most important of these is the temporary void left behind by a coronal mass ejection (CME). Massive, fast CMEs tend to leave behind a darker void that also usually corresponds to minimum irradiance for the cooler coronal emissions. If the dimming is associated with a solar are, as is often the case, the are component of the irradiance light curve in the cooler coronal emission can be isolated and removed using simultaneous measurements of warmer coronal lines. We apply this technique to 37dimming events identified during two separate two-week periods in 2011, plus an event on 2010 August 7 analyzed in a previous paper, to parameterize dimming in terms of depth and slope. We provide statistics on which combination of wavelengths worked best for the flare-removal method, describe the fitting methods applied to the dimming light curves, and compare the dimming parameters with corresponding CME parameters of mass and speed. The best linear relationships found are nu(sub CME) [km/s] approx. equals 2.36 x 10 6 [km/%] x s(sub dim) [%/s] m(sub CME) [g] approx. equals 2.59 x 10(exp.15 [g/%] x the square root of d(sub dim) [%].These relationships could be used for space weather operations of estimating CME mass and speed using near-real-time irradiance dimming measurements.

Dynamic Moss Observed with Hi-C

NASA Technical Reports Server (NTRS)

Alexander, Caroline; Winebarger, Amy; Morton, Richard; Savage, Sabrina

2014-01-01

The High-resolution Coronal Imager (Hi-C), flown on 11 July 2012, has revealed an unprecedented level of detail and substructure within the solar corona. Hi-­-C imaged a large active region (AR11520) with 0.2-0.3'' spatial resolution and 5.5s cadence over a 5 minute period. An additional dataset with a smaller FOV, the same resolution, but with a higher temporal cadence (1s) was also taken during the rocket flight. This dataset was centered on a large patch of 'moss' emission that initially seemed to show very little variability. Image processing revealed this region to be much more dynamic than first thought with numerous bright and dark features observed to appear, move and disappear over the 5 minute observation. Moss is thought to be emission from the upper transition region component of hot loops so studying its dynamics and the relation between the bright/dark features and underlying magnetic features is important to tie the interaction of the different atmospheric layers together. Hi-C allows us to study the coronal emission of the moss at the smallest scales while data from SDO/AIA and HMI is used to give information on these structures at different heights/temperatures. Using the high temporal and spatial resolution of Hi-C the observed moss features were tracked and the distribution of displacements, speeds, and sizes were measured. This allows us to comment on both the physical processes occurring within the dynamic moss and the scales at which these changes are occurring.

Dynamic Moss Observed with Hi-C

NASA Technical Reports Server (NTRS)

Alexander, Caroline; Winebarger, Amy; Morton, Richard; Savage, Sabrina

2014-01-01

The High-resolution Coronal Imager (Hi-C), flown on 11 July 2012, has revealed an unprecedented level of detail and substructure within the solar corona. Hi-C imaged a large active region (AR11520) with 0.2-0.3'' spatial resolution and 5.5s cadence over a 5 minute period. An additional dataset with a smaller FOV, the same resolution, but with a higher temporal cadence (1s) was also taken during the rocket flight. This dataset was centered on a large patch of 'moss' emission that initially seemed to show very little variability. Image processing revealed this region to be much more dynamic than first thought with numerous bright and dark features observed to appear, move and disappear over the 5 minute observation. Moss is thought to be emission from the upper transition region component of hot loops so studying its dynamics and the relation between the bright/dark features and underlying magnetic features is important to tie the interaction of the different atmospheric layers together. Hi-C allows us to study the coronal emission of the moss at the smallest scales while data from SDO/AIA and HMI is used to give information on these structures at different heights/temperatures. Using the high temporal and spatial resolution of Hi-C the observed moss features were tracked and the distribution of displacements, speeds, and sizes were measured. This allows us to comment on both the physical processes occurring within the dynamic moss and the scales at which these changes are occurring.

Gradual Streamer Expansions and the Relationship between Blobs and Inflows

NASA Astrophysics Data System (ADS)

Wang, Y.-M.; Hess, P.

2018-06-01

Coronal helmet streamers show a continual tendency to expand outward and pinch off, giving rise to flux ropes that are observed in white light as “blobs” propagating outward along the heliospheric current/plasma sheet. The blobs form within the r ∼ 2–6 R ⊙ heliocentric range of the Large Angle and Spectrometric Coronagraph (LASCO) C2 instrument, but the expected inward-moving counterparts are often not detected. Here we show that the height of blob formation varies as a function of the underlying photospheric field, with the helmet streamer loops expanding to greater heights when active regions (ARs) emerge underneath them. When the pinch-offs occur at r ∼ 3–4 R ⊙, diverging inward/outward tracks sometimes appear in height–time maps constructed from LASCO C2 running-difference images. When the underlying photospheric field is weak, the blobs form closer to the inner edge of the C2 field of view and only the outward tracks are clearly visible. Conversely, when the emergence of large ARs leads to a strengthening of the outer coronal field and an increase in the total white-light radiance (as during late 2014), the expanding helmet-streamer loops pinch off beyond r ∼ 4 R ⊙, triggering strong inflow streams whose outgoing counterparts are usually very faint. We deduce that the visibility of the blobs and inflows depends on the amount of material that the diverging components sweep up within the 2–6 R ⊙ field of view. We also note that the rate of blob production tends to increase when a helmet streamer is “activated” by underlying flux emergence.

Two-phase Heating in Flaring Loops

NASA Astrophysics Data System (ADS)

Zhu, Chunming; Qiu, Jiong; Longcope, Dana W.

2018-03-01

We analyze and model a C5.7 two-ribbon solar flare observed by the Solar Dynamics Observatory, Hinode, and GOES on 2011 December 26. The flare is made of many loops formed and heated successively over one and half hours, and their footpoints are brightened in the UV 1600 Å before enhanced soft X-ray and EUV missions are observed in flare loops. Assuming that anchored at each brightened UV pixel is a half flaring loop, we identify more than 6700 half flaring loops, and infer the heating rate of each loop from the UV light curve at the footpoint. In each half loop, the heating rate consists of two phases: intense impulsive heating followed by a low-rate heating that is persistent for more than 20 minutes. Using these heating rates, we simulate the evolution of their coronal temperatures and densities with the model of the “enthalpy-based thermal evolution of loops.” In the model, suppression of thermal conduction is also considered. This model successfully reproduces total soft X-ray and EUV light curves observed in 15 passbands by four instruments GOES, AIA, XRT, and EVE. In this flare, a total energy of 4.9 × 1030 erg is required to heat the corona, around 40% of this energy is in the slow-heating phase. About two-fifths of the total energy used to heat the corona is radiated by the coronal plasmas, and the other three fifth transported to the lower atmosphere by thermal conduction.

Electrical energy sources for organic synthesis on the early earth

NASA Technical Reports Server (NTRS)

Chyba, Christopher; Sagan, Carl

1991-01-01

It is pointed out that much of the contemporary origin-of-life research uses the original estimates of Miller and Urey (1959) for terrestrial energy dissipation by lightning and coronal discharges being equal to 2 x 10 to the 19th J/yr and 6 x 10 to the 19th J/yr, respectively. However, data from experiments that provide analogues to naturally-occurring lightning and coronal discharges indicate that lightning energy yields for organic synthesis (nmole/J) are about one order of magnitude higher than the coronal discharge yields. This suggests that, on early earth, organic production by lightning may have dominated that due to coronal emission. New values are recommended for lightning and coronal discharge dissipation rates on the early earth, 1 x 10 to the 18th J/yr and 5 x 10 to the 17th J/yr, respectively.

Solar C: Scatter-Free Observatory for Limb Active Regions and Coronae

NASA Technical Reports Server (NTRS)

2004-01-01

The SOLARC observatory is a 0.5m off-axis reflecting coronagraph. NASA SRT funding has allowed the completion of this telescope facility, which we believe is now the world's largest operational coronagraph. We have achieved our proposal goals both in the development of the new technology for this facility and in the demonstration of its scientific and educational potential: 1) The SOLARC engineering development was successful and has spawned other similar instruments. The off-axis design of ATST (a new 4m telescope) has benefited from the SOLARC development. The off-axis 1.6m NST facility at BBSO is also now under construction and will be the world's largest solar disk observing telescope until ATST is completed. Both of these telescope designs are derivatives of the SOLARC 0.5m off-axis. Some of this technical development is described in the publications. 2) The most important scientific goal of SOLARC has been to demonstrate that coronal magnetic fields can be measured using infrared spectropolarimetry techniques. With the completion of the optical fiber-bundle imaging spectropolarimeter we have measured the coronal field strength with a sensitivity to the line-of-sight field component of 2G at 150,OOOkm above the limb. We believe this capability opens new opportunities for space weather, and coronal physics research. In particular we have demonstrated a new tool for understanding the effect of the Sun on the terrestrial space environment. A paper reporting these results has recently been submitted to the Astrophysical Journal Letters.

CORONAL DYNAMIC ACTIVITIES IN THE DECLINING PHASE OF A SOLAR CYCLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jang, Minhwan; Choe, G. S.; Woods, T. N.

2016-12-10

It has been known that some solar activity indicators show a double-peak feature in their evolution through a solar cycle, which is not conspicuous in sunspot number. In this Letter, we investigate the high solar dynamic activity in the declining phase of the sunspot cycle by examining the evolution of polar and low-latitude coronal hole (CH) areas, splitting and merging events of CHs, and coronal mass ejections (CMEs) detected by SOHO /LASCO C3 in solar cycle 23. Although the total CH area is at its maximum near the sunspot minimum, in which polar CHs prevail, it shows a comparable secondmore » maximum in the declining phase of the cycle, in which low-latitude CHs are dominant. The events of CH splitting or merging, which are attributed to surface motions of magnetic fluxes, are also mostly populated in the declining phase of the cycle. The far-reaching C3 CMEs are also overpopulated in the declining phase of the cycle. From these results we suggest that solar dynamic activities due to the horizontal surface motions of magnetic fluxes extend far in the declining phase of the sunspot cycle.« less

Solar and stellar coronal plasmas

NASA Technical Reports Server (NTRS)

Golub, Leon

1989-01-01

Progress in observational, theoretical, and radio studies of coronal plasmas is summarized. Specifically work completed in the area of solar and stellar magnetic fields, related photospheric phenomena and the relationships between magnetism, rotation, coronal and chromospheric emission in solar-like stars is described. Also outlined are theoretical studies carried out in the following areas, among others: (1) neutral beams as the dominant energy transport mechanism in two ribbon-flares; (2) magneto hydrodynamic and circuit models for filament eruptions; and (3) studies of radio emission mechanisms in transient events. Finally, radio observations designed for coronal activity studies of the sun and of solar-type coronae are described. A bibliography of publications and talks is provided along with reprints of selected articles.

A Multiwavelength Study of Coronal Structure: A Simultaneous Observation from NIXT and YOHKOH

NASA Technical Reports Server (NTRS)

Golub, Leon

1998-01-01

Solar soft X-ray images taken simultaneously by the Yohkoh and the Normal Incidence X-ray Telescope (NIXT) reveal significantly different coronal structures. Coronal loops are more clearly seen in the Yohkoh images, and the isolated island-like structures seen in the NIXT image have been found to correspond to the footpoints of the Yohkoh loops. The difference is due to the difference in the temperature response of the telescopes: NIXT is sensitive to temperatures ranging from 0.9 to 3 MK, while Yohkoh is more sensitive to temperatures above 2.5 MK. The morphological differences reflect the multi-temperature (1-5 MK) nature of the solar coronal plasmas.

Coronal propagation of flare associated electrons and protons

NASA Technical Reports Server (NTRS)

Schellert, G.; Wibberenz, G.; Kunow, H.

1985-01-01

A statistical study of characteristic times and intensities of 36 solar particle events observed between 1977 and 1979 by the Kiel Cosmic Ray Experiment on board HELIOS-1 and -2 has been carried out. For approx. 0.5 MeV electrons we order the times of maximum and the absolute intensities with respect to angular distance from the parent flare. Discussion of coronal parameters in terms of Reid's model leads to typical time constants for coronal diffusion and escape.

Automatic recognition of coronal type II radio bursts: The ARBIS 2 method and first observations

NASA Astrophysics Data System (ADS)

Lobzin, Vasili; Cairns, Iver; Robinson, Peter; Steward, Graham; Patterson, Garth

Major space weather events such as solar flares and coronal mass ejections are usually accompa-nied by solar radio bursts, which can potentially be used for real-time space weather forecasts. Type II radio bursts are produced near the local plasma frequency and its harmonic by fast electrons accelerated by a shock wave moving through the corona and solar wind with a typi-cal speed of 1000 km s-1 . The coronal bursts have dynamic spectra with frequency gradually falling with time and durations of several minutes. We present a new method developed to de-tect type II coronal radio bursts automatically and describe its implementation in an extended Automated Radio Burst Identification System (ARBIS 2). Preliminary tests of the method with spectra obtained in 2002 show that the performance of the current implementation is quite high, ˜ 80%, while the probability of false positives is reasonably low, with one false positive per 100-200 hr for high solar activity and less than one false event per 10000 hr for low solar activity periods. The first automatically detected coronal type II radio bursts are also presented. ARBIS 2 is now operational with IPS Radio and Space Services, providing email alerts and event lists internationally.

Coronal leakage of four intracanal medications after exposure to human saliva in the presence of a temporary filling material.

PubMed

Verissimo, Rebeca Dibe; Gurgel-Filho, Eduardo Diogo; De-Deus, Gustavo; Coutinho-Filho, Tauby; de Souza-Filho, Francisco Jose

2010-01-01

To determine the time required for the recontamination of root canals medicated with four different materials. A total of 60 intact, caries-free, human single-rooted teeth with straight roots were selected for this study. After chemo-mechanical preparation they must be changed in the specimens into seven groups: 10 teeth medicated with calcium hydroxide (Ca(OH) 2) + Camphorated paramonochlorophanol (CPMC) (G.1); 10 medicated with 2.5% Sodium hypochlorite (NaOCL) (G.2); 10 medicated with 2% Chlorhexidine gluconate (CHX) in gel (G.3); 10 medicated with 2% CHX in gel + Ca(OH) 2 (G.4); 10 without intracanal medicament and sealed with a coronal temporary filling (G.5). Five teeth were without intracanal medicament and coronally unsealed, used as the positive control group (PC) (G.6) and 5 teeth with intact crowns used as the negative control group (NC) (G.7). Glass vials with rubber stoppers were adjusted for use. The medicaments were prepared and injected into the root canals using sterile plastic syringes. An apparatus was used to evaluate for 30 days leakage. The chamber was filled with 3 ml of human saliva and Brain Heart Infusion (BHI) broth, incubated at 37 degrees C and checked daily for the appearance of turbidity in the BHI broth. Recontamination was detected after an average time of 2.6 days in group 2, 15.9 days in group 3, 30 days in group 1, 27.6 days in group 4, 2.9 days in group 5, 1 day in the positive control, and there was no contamination in the negative control group. The NaOCl group showed the highest worst average of recontamination; on the other hand, high averages were also shown by Ca(OH) 2 + CPMC and Ca(OH) 2 + 2% CHX in gel.

Reliability of a new method for measuring coronal trunk imbalance, the axis-line-angle technique.

PubMed

Zhang, Rui-Fang; Liu, Kun; Wang, Xue; Liu, Qian; He, Jia-Wei; Wang, Xiang-Yang; Yan, Zhi-Han

2015-12-01

Accurate determination of the extent of trunk imbalance in the coronal plane plays a key role in an evaluation of patients with trunk imbalance, such as patients with adolescent idiopathic scoliosis. An established, widely used practice in evaluating trunk imbalance is to drop a plumb line from the C7 vertebra to a key reference axis, the central sacral vertical line (CSVL) in full-spine standing anterioposterior radiographs, and measuring the distance between them, the C7-CSVL. However, measuring the CSVL is subject to intraobserver differences, is error-prone, and is of poor reliability. Therefore, the development of a different way to measure trunk imbalance is needed. This study aimed to describe a new method to measure coronal trunk imbalance, the axis-line-angle technique (ALAT), which measures the angle at the intersection between the C7 plumb line and an axis line drawn from the vertebral centroid of the C7 to the middle of the superior border of the symphysis pubis, and to compare the reliability of the ALAT with that of the C7-CSVL. A prospective study at a university hospital was used. The patient sample consisted of sixty-nine consecutively enrolled men and women patients, aged 10-18 years, who had trunk imbalance defined as C7-CSVL longer than 20 mm on computed full-spine standing anterioposterior radiographs. Data were analyzed to determine the correlation between C7-CSVL and ALAT measurements and to determine intraobserver and interobserver reliabilities. Using a picture archiving and communication system, three radiologists independently evaluated trunk imbalance on the 69 computed radiographs by measuring the C7-CSVL and by measuring the angle determined by the ALAT. Data were analyzed to determine the correlations between the two measures of trunk imbalance, and to determine intraobserver and interobserver reliabilities of each of them. Overall results from the measurements by the C7-CSVL and the ALAT were significantly moderately correlated. Intraobserver assessments by measuring the C7-CSVL and by doing the ALAT failed to find any significant differences between the findings from the first and second assessments by the same radiologist. Interobserver assessments significantly differed between radiologists 1 and 2 for the first assessment measuring the C7-CSVL, and between radiologists 2 and 3 for the second assessment measuring the C7-CSVL. Interobserver assessments by doing the ALAT failed to find any significant differences among the three radiologists for either of the two assessments. Our results indicated that using the ALAT, which is simple and convenient, is of great value in measuring trunk imbalance. For measuring trunk imbalance, the ALAT has essential advantages compared with measuring the C7-CSVL. We encourage spine surgeons to consider using the ALAT in evaluating trunk imbalance. Copyright © 2015 Elsevier Inc. All rights reserved.

Do solar decimetric spikes originate in coronal X-ray sources?

NASA Astrophysics Data System (ADS)

Battaglia, M.; Benz, A. O.

2009-06-01

Context: In the standard solar flare scenario, a large number of particles are accelerated in the corona. Nonthermal electrons emit both X-rays and radio waves. Thus, correlated signatures of the acceleration process are predicted at both wavelengths, coinciding either close to the footpoints of a magnetic loop or near the coronal X-ray source. Aims: We attempt to study the spatial connection between coronal X-ray emission and decimetric radio spikes to determine the site and geometry of the acceleration process. Methods: The positions of radio-spike sources and coronal X-ray sources are determined and analyzed in a well-observed limb event. Radio spikes are identified in observations from the Phoenix-2 spectrometer. Data from the Nançay radioheliograph are used to determine the position of the radio spikes. RHESSI images in soft and hard X-ray wavelengths are used to determine the X-ray flare geometry. Those observations are complemented by images from GOES/SXI. Results: We find that the radio emission originates at altitudes much higher than the coronal X-ray source, having an offset from the coronal X-ray source amounting to 90´´ and to 113´´ and 131´´ from the two footpoints, averaged over time and frequency. Conclusions: Decimetric spikes do not originate from coronal X-ray flare sources contrary to previous expectations. However, the observations suggest a causal link between the coronal X-ray source, related to the major energy release site, and simultaneous activity in the higher corona.

Temporal evolution of solar wind ion composition and their source coronal holes during the declining phase of cycle 23. I. Low-latitude extension of polar coronal holes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ko, Yuan-Kuen; Wang, Yi-Ming; Muglach, Karin

2014-06-01

We analyzed 27 solar wind (SW) intervals during the declining phase of cycle 23, whose source coronal holes (CHs) can be unambiguously identified and are associated with one of the polar CHs. We found that the SW ions have a temporal trend of decreasing ionization state, and such a trend is different between the slow and fast SW. The photospheric magnetic field, both inside and at the outside boundary of the CH, also exhibits a trend of decrease with time. However, EUV line emissions from different layers of the atmosphere exhibit different temporal trends. The coronal emission inside the CHmore » generally increases toward the CH boundary as the underlying field increases in strength and becomes less unipolar. In contrast, this relationship is not seen in the coronal emission averaged over the entire CH. For C and O SW ions that freeze-in at lower altitude, stronger correlation between their ionization states and field strength (both signed and unsigned) appears in the slow SW, while for Fe ions that freeze-in at higher altitude, stronger correlation appears in the fast SW. Such correlations are seen both inside the CH and at its boundary region. On the other hand, the coronal electron temperature correlates well with the SW ion composition only in the boundary region. Our analyses, although not able to determine the likely footpoint locations of the SW of different speeds, raise many outstanding questions for how the SW is heated and accelerated in response to the long-term evolution of the solar magnetic field.« less

The Triggering Mechanism of Quiet-Region Coronal Jet Eruptions: Flux Cancelation

NASA Technical Reports Server (NTRS)

Panesar, Navdeep K.; Sterling, Alphonse C.; Moore, Ronald L.

2017-01-01

Coronal jets are frequent transient features on the Sun, observed in EUV and X-ray emissions. They occur in active regions, quiet Sun and coronal holes, and appear as a bright spire with base brightenings. Recent studies show that many coronal jets are driven by the eruption of a minifilament. Here we investigate the magnetic cause of jet-driving minifilament eruptions. We study ten randomly-found on-disk quiet-region coronal jets using SDO/AIA intensity images and SDO/HMI magnetograms. For all ten events, we track the evolution of photospheric magnetic flux in the jet-base region in EUV images and find that (a) a cool (transition-region temperature) minifilament is present prior to each jet eruption; (b) the pre-eruption minifilament resides above the polarity-inversion line between majority-polarity and minority-polarity magnetic flux patches; (c) the opposite-polarity flux patches converge and cancel with each other; (d) the cancelation between the majority-polarity and minority-polarity flux patches eventually destabilizes the field holding the minifilament to erupt outwards; (e) the envelope of the erupting field barges into ambient oppositely-directed far-reaching field and undergoes external reconnection (interchange reconnection); (f) the external reconnection opens the envelope field and the minifilament field inside, allowing reconnected-heated hot material and cool minifilament material to escape along the far-reaching field, producing the jet spire. In summary, we found that each of our ten jets resulted from a minifilament eruption following flux cancelation at the magnetic neutral line under the pre-eruption minifilament. These observations show that flux cancelation is usually the trigger of quiet-region coronal jet eruptions.

Large-Scale Coronal Heating from "Cool" Activity in the Solar Magnetic Network

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Hathaway, D. H.

1999-01-01

In Fe XII images from SOHO/EIT, the quiet solar corona shows structure on scales ranging from sub-supergranular (i.e., bright points and coronal network) to multi-supergranular (large-scale corona). In Falconer et al 1998 (Ap.J., 501, 386) we suppressed the large-scale background and found that the network-scale features are predominantly rooted in the magnetic network lanes at the boundaries of the supergranules. Taken together, the coronal network emission and bright point emission are only about 5% of the entire quiet solar coronal Fe XII emission. Here we investigate the relationship between the large-scale corona and the network as seen in three different EIT filters (He II, Fe IX-X, and Fe XII). Using the median-brightness contour, we divide the large-scale Fe XII corona into dim and bright halves, and find that the bright-half/dim half brightness ratio is about 1.5. We also find that the bright half relative to the dim half has 10 times greater total bright point Fe XII emission, 3 times greater Fe XII network emission, 2 times greater Fe IX-X network emission, 1.3 times greater He II network emission, and has 1.5 times more magnetic flux. Also, the cooler network (He II) radiates an order of magnitude more energy than the hotter coronal network (Fe IX-X, and Fe XII). From these results we infer that: 1) The heating of the network and the heating of the large-scale corona each increase roughly linearly with the underlying magnetic flux. 2) The production of network coronal bright points and heating of the coronal network each increase nonlinearly with the magnetic flux. 3) The heating of the large-scale corona is driven by widespread cooler network activity rather than by the exceptional network activity that produces the network coronal bright points and the coronal network. 4) The large-scale corona is heated by a nonthermal process since the driver of its heating is cooler than it is. This work was funded by the Solar Physics Branch of NASA's office of Space Science through the SR&T Program and the SEC Guest Investigator Program.