Effect of calcium chloride solution immersion on surface hardness of restorative glass ionomer cements.

PubMed

Shiozawa, Maho; Takahashi, Hidekazu; Iwasaki, Naohiko; Uo, Motohiro

2013-01-01

The objective of this study was to evaluate the effect of the concentration of calcium chloride (CaCl2) solution on the surface hardness of restorative glass ionomer cements (GICs). Two high-viscosity GICs, Fuji IX GP and GlasIonomer FX-II, were immersed in several concentrations of CaCl2 solution for 1 day and 1 week. The immersed specimen surfaces were evaluated using microhardness testing, grazing incidence X-ray diffraction, and energy-dispersive X-ray spectroscopy. Immersion in a higher concentration of CaCl2 solution produced a greater increase in the surface hardness. No crystalline substance was observed on the immersed surface. Calcium ions were selectively absorbed in the matrix of the GIC surface after immersion. They reacted with the non-reacted carboxylic acid groups remaining in the cement matrix. These reactions were considered to cause an increase in the surface hardness of the GICs.

The complex of xylan and iodine: the induction and detection of nanoscale order

Treesearch

Xiaochun Yu; Rajai H. Atalla

2005-01-01

The complex of xylan and iodine and its formation in a solution of xylan, CaCl2, and I2 + KI was investigated by UV/Vis, second-derivative UV/Vis, and Raman spectroscopy. The complex forms only at very high concentrations of CaCl2, suggesting that when the water available in the solution is not sufficient to fully hydrate the calcium cation the chelation with the...

Near-infrared spectroscopic investigation of water in supercritical CO2 and the effect of CaCl2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zheming; Felmy, Andrew R.; Thompson, Christopher J.

2013-01-01

Near-infrared (NIR) spectroscopy was applied to investigate the dissolution and chemical interaction of water dissolved into supercritical carbon dioxide (scCO2) and the influence of CaCl2 in the co-existing aqueous phase at fo empe e : 40 50 75 nd 100 C at 90 atm. Consistent with the trend of the vapor pressure of water, the solubility of pure water in scCO2 inc e ed f om 40 °C (0.32 mole%) o 100 °C (1.61 mole%). The presence of CaCl2 negatively affects the solubility of water in scCO2: at a given temperature and pressure the solubility of water decreased as themore » concentration of CaCl2 in the aqueous phase increased, following the trend of the activity of water. A 40 °C, the water concentration in scCO2 in contact with saturated CaCl2 aqueous solution was only 0.16 mole%, a drop of more than 50% as compared to pure water while that a 100 °C was 1.12 mole%, a drop of over 30% as compared to pure water, under otherwise the same conditions. Analysis of the spectral profiles suggested that water dissolved into scCO2 exists in the monomeric form under the evaluated temperature and pressure conditions, for both neat water and CaCl2 solutions. However, its rotational degrees of freedom decrease at lower temperatures due to higher fluid densities, leading to formation of weak H2O:CO2 Lewis acid-base complexes. Similarly, the nearly invariant spectral profiles of dissolved water in the presence and absence of saturated CaCl2 under the same experimental conditions was taken as evidence that CaCl2 dissolution in scCO2 was limited as the dissolved Ca2+/CaCl2 would likely be highly hydrated and would alter the overall spectra of waters in the scCO2 phase.« less

Assessment risk of phosphorus leaching from calcareous soils using soil test phosphorus.

PubMed

Jalali, Mohsen; Jalali, Mahdi

2017-03-01

Accurate estimation of phosphorus (P) leaching is important because excess P may reduce surface and ground water quality. Little attention has been paid to estimate P leaching from soil tests in calcareous soils. The relation between different soil tests P (STP), P sorption index (PSI) and degree of P saturation (DPS) and leaching of P were examined for assessing the risk of P loss from calcareous soils. Columns leaching repacked with native soils were leached with either distilled water or 10 mM CaCl 2 solutions, separately. Four leaching events were performed at four days, and 28.7 mm of distilled water or 10 mM CaCl 2 solutions was applied at each leaching events. Compared with distilled water, CaCl 2 had a small ability to solubilize P from soils. Concentration of P in leachate in both leaching solutions was exceeding 0.1 mg l -1 associated with eutrophication. Cumulative P leached P was ranged from 0.17 to 18.59 mg P kg -1 and 0.21-8.16 mg P kg -1 , when distilled water and 10 mM CaCl 2 solutions were applied, respectively and it was higher in sandy clay loam soils compared with clay soils. Among evaluated environmental soil P tests, P CaCl2-3h (P extracted by 10 mM CaCl 2 for 3 h), P CaCl2-1h (P extracted by 10 mM CaCl 2 for 1 h) were more accurate than other soil P tests for predicting P concentration in the leachates in both leaching solutions and accounting for 83% and 72% of variation of P concentration, respectively. The water extractable P (WEP) (r = 0.771) and Olsen-P (P Ols )(r = 0.739) were significantly related to the leached P concentration using distilled water solution in a split line model, with a change point of 27.4 mg P kg -1 and 61.5 mg P kg -1 , respectively. Various DPS were calculated and related to the leached P concentration. Based on P extracted by Mehlich-3 (P M3 ) and HCl (P HCl ) and PSI, the change point of the relationship between leached P concentration and DPS M3-3 (P M3 (P M3 +PSI)×100) and DPS HCl-2 (P HCl (P HCl +PSI)×100) for both leaching solutions was approximately the same, thus a mean value of 49% for DPS M3-3 and 73% for DPS HCl-2 was obtained. Soils were grouped into four categories of increasing P leaching potential based on WEP, P Ols , and DPS M3-3 . The results indicated that 8.00%-25.50% of the soil grouped in no risk category whereas 8.00%-13.70% of the soils fell into the high risk category. Copyright © 2016 Elsevier Ltd. All rights reserved.

Restaurant consumer acceptance of beef loin strip steaks tenderized with calcium chloride.

PubMed

Hoover, L C; Cook, K D; Miller, M F; Huffman, K L; Wu, C K; Lansdell, J L; Ramsey, C B

1995-12-01

Beef strip loins from either the right or left side of 22 carcasses of Bos indicus-type steers were injected with 200 mM calcium chloride (CaCl2) solution at 5% (wt/wt) to determine its effect on tenderness and other selected quality traits of steaks. Loins from opposite sides of the carcasses were untreated and served as the control. The steaks were evaluated for tenderness, juiciness, flavor intensity, tenderness acceptability, and overall acceptability by 62 restaurant consumers over a 6-wk period. The CaCl2 injection improved (P < .05) tenderness and flavor intensity ratings by the restaurant consumers. Tenderness acceptability and overall acceptability were improved 23 and 17%, respectively, by the CaCl2 injection. Flavor was not compromised by the CaCl2 injection. The CaCl2-treated steaks were rated superior(P < .05) for flavor compared to the control steaks. Restaurant consumers preferred the beef loin strip steaks injected with 200 mM CaCl2 at 5% (wt/wt). The results of this study are interpreted to indicate that, from a restaurant consumer perspective, CaCl2 injection is an acceptable means of making beef a more consistently tender product.

Intestinal absorption of calcium from calcium ascorbate in rats.

PubMed

Tsugawa, N; Yamabe, T; Takeuchi, A; Kamao, M; Nakagawa, K; Nishijima, K; Okano, T

1999-01-01

The intestinal absorption of calcium (Ca) from Ca ascorbate (Ca-AsA) was investigated in normal rats. Each animal was perorally administered either 5mg (low dose) or 10mg (high dose) of Ca in 1ml of distilled water as Ca-AsA, Ca carbonate (CaCO3), or Ca chloride (CaCl2), which were intrinsically labeled with 45Ca using 45CaCl2. The amount of radioactivity in plasma was measured periodically up to 34h after dosing, and pharmacokinetic parameters were calculated from the radioactivity in plasma. The time taken to reach the maximum 45Ca level (Tmax) did not differ among the three groups. The area under the plasma 45Ca level/time curve (AUCinfinity) value for the Ca-AsA group was significantly higher than those for the CaCO3 and the CaCl2 groups. The radioactivity at Tmax (Cmax) for the Ca-AsA group was significantly higher than those for the CaCO3 and the CaCl2 groups for the low dose, and comparable with or significantly higher than those for the CaCl2 and CaCO3 groups for the high dose. Similar results were observed for whole-body 45Ca retention. Radioactivity in the femur 34h after dosing was the highest in the Ca-AsA group and the lowest in the CaCO3 group. The rank order of solubility in water, the first fluid (pH 1.2, JP-1) of JPXIII disintegration medium, acetate buffer solution (pH 4.0), triethanolamine-malate buffer solution (pH 7.0) and ammonium chloride buffer solution (pH 10.0) at 37 degrees C was CaCl2 > Ca-AsA > CaCO3. In contrast, the rank order of the solubility in the second fluid (pH 6.8, JP-2) of JPXIII disintegration medium at 37 degrees C was Ca-AsA > CaCl2 > CaCO3. These results indicate that the absorbability of Ca from Ca-AsA is almost comparable with, or higher than, that from CaCl2 and significantly higher than that from CaCO3 because of its high degree of solubility in the intestine. Therefore, Ca-AsA would be useful as a Ca supplement with relatively high absorption from intestine.

Molecular dynamics simulation, ab initio calculation, and size-selected anion photoelectron spectroscopy study of initial hydration processes of calcium chloride.

PubMed

He, Zhili; Feng, Gang; Yang, Bin; Yang, Lijiang; Liu, Cheng-Wen; Xu, Hong-Guang; Xu, Xi-Ling; Zheng, Wei-Jun; Gao, Yi Qin

2018-06-14

To understand the initial hydration processes of CaCl 2 , we performed molecular simulations employing the force field based on the theory of electronic continuum correction with rescaling. Integrated tempering sampling molecular dynamics were combined with ab initio calculations to overcome the sampling challenge in cluster structure search and refinement. The calculated vertical detachment energies of CaCl 2 (H 2 O) n - (n = 0-8) were compared with the values obtained from photoelectron spectra, and consistency was found between the experiment and computation. Separation of the Cl-Ca ion pair is investigated in CaCl 2 (H 2 O) n - anions, where the first Ca-Cl ionic bond required 4 water molecules, and both Ca-Cl bonds are broken when the number of water molecules is larger than 7. For neutral CaCl 2 (H 2 O) n clusters, breaking of the first Ca-Cl bond starts at n = 5, and 8 water molecules are not enough to separate the two ion pairs. Comparing with the observations on magnesium chloride, it shows that separating one ion pair in CaCl 2 (H 2 O) n requires fewer water molecules than those for MgCl 2 (H 2 O) n . Coincidentally, the solubility of calcium chloride is higher than that of magnesium chloride in bulk solutions.

Chemical potentials of alkaline earth metal halide aqueous electrolytes and solubility of their hydrates by molecular simulation: Application to CaCl2, antarcticite, and sinjarite

NASA Astrophysics Data System (ADS)

Moučka, Filip; Kolafa, Jiří; Lísal, Martin; Smith, William R.

2018-06-01

We present a molecular-level simulation study of CaCl2 in water and crystalline hydrates formed by CaCl2 at ambient (298.15 K, 1 bar) conditions and at a high-temperature high-pressure state (365 K, 275 bars) typical of hydraulic fracturing conditions in natural-gas extraction, at which experimental properties are poorly characterized. We focus on simulations of chemical potentials in both solution and crystalline phases and on the salt solubility, the first time to our knowledge that such properties have been investigated by molecular simulation for divalent aqueous electrolytes. We first extend our osmotic ensemble Monte Carlo simulation technique [F. Moučka et al., J. Phys. Chem. B 115, 7849-7861 (2011)] to such solutions. We then describe and apply new methodology for the simulation of the chemical potentials of the experimentally observed crystalline hydrates at ambient conditions (antarcticite, CaCl2.6H2O) and at high-temperature conditions (sinjarite, CaCl2.2H2O). We implement our methodologies using for both phases the CaCl2 transferable force field (FF) based on simple point charge-extended water developed by Mamatkulov et al. [J. Chem. Phys. 138, 024505 (2013)], based on training sets involving single-ion and ion-pair low-concentration solution properties at near-ambient conditions. We find that simulations of the solution chemical potentials at high concentrations are somewhat problematic, exhibiting densities diverging from experimental values and accompanied by dramatically decreasing particle mobility. For the solid phases, the sinjarite crystalline lattice differs from experiment only slightly, whereas the simulations of antarcticite completely fail, due to instability of the crystalline lattice. The FF thus only successfully yields the sinjarite solubility, but its value m = 8.0(7) mol kg-1H2O lies well below the experimentally observed solubility range at 1 bar pressure of (12m, 15m) in the temperature interval (320 K, 400 K). We conclude that the used FF does not provide a good description of the experimental properties considered and suggest that improvement must take into account the crystalline properties.

Chemical potentials of alkaline earth metal halide aqueous electrolytes and solubility of their hydrates by molecular simulation: Application to CaCl2, antarcticite, and sinjarite.

PubMed

Moučka, Filip; Kolafa, Jiří; Lísal, Martin; Smith, William R

2018-06-14

We present a molecular-level simulation study of CaCl 2 in water and crystalline hydrates formed by CaCl 2 at ambient (298.15 K, 1 bar) conditions and at a high-temperature high-pressure state (365 K, 275 bars) typical of hydraulic fracturing conditions in natural-gas extraction, at which experimental properties are poorly characterized. We focus on simulations of chemical potentials in both solution and crystalline phases and on the salt solubility, the first time to our knowledge that such properties have been investigated by molecular simulation for divalent aqueous electrolytes. We first extend our osmotic ensemble Monte Carlo simulation technique [F. Moučka et al., J. Phys. Chem. B 115, 7849-7861 (2011)] to such solutions. We then describe and apply new methodology for the simulation of the chemical potentials of the experimentally observed crystalline hydrates at ambient conditions (antarcticite, CaCl 2 ·6H 2 O) and at high-temperature conditions (sinjarite, CaCl 2 ·2H 2 O). We implement our methodologies using for both phases the CaCl 2 transferable force field (FF) based on simple point charge-extended water developed by Mamatkulov et al. [J. Chem. Phys. 138, 024505 (2013)], based on training sets involving single-ion and ion-pair low-concentration solution properties at near-ambient conditions. We find that simulations of the solution chemical potentials at high concentrations are somewhat problematic, exhibiting densities diverging from experimental values and accompanied by dramatically decreasing particle mobility. For the solid phases, the sinjarite crystalline lattice differs from experiment only slightly, whereas the simulations of antarcticite completely fail, due to instability of the crystalline lattice. The FF thus only successfully yields the sinjarite solubility, but its value m = 8.0(7) mol kg -1 H 2 O lies well below the experimentally observed solubility range at 1 bar pressure of (12m, 15m) in the temperature interval (320 K, 400 K). We conclude that the used FF does not provide a good description of the experimental properties considered and suggest that improvement must take into account the crystalline properties.

Laboratory studies of the low-temperature deliquescence of calcium chloride salts: Relevance to aqueous solutions on Mars and in the Antarctic Dry Valleys

NASA Astrophysics Data System (ADS)

Gough, R. V.; Chevrier, V.; Tolbert, M. A.

2013-12-01

There is significant interest in the possible existence of liquid water on current Mars. This water would likely exist as a brine in order to be stable on Mars today. It has been proposed that soil salts could form aqueous solutions through either the melting of ice by low-eutectic salts, or by the deliquescence of hygroscopic salts present in the Martian soil. The focus thus far has largely been on perchlorate species, which can melt ice at temperatures as low as 206 K and can deliquesce at relative humidity values as low as 38% RH. A Mars-relevant salt that has been neglected thus far is calcium chloride (CaCl2). Calcium has been reported to be an abundant cation at the Phoenix landing site and Mars Science Laboratory instruments have recently identified calcium as well. Simulations suggest subsurface CaCl2 is an ideal candidate to produce brines with seasonality consistent with observed recurring slope lineae (RSL) (Chevrier et al., 2012). Finally, the only terrestrial site where RSL-like features have been observed (near Don Juan Pond in the Antarctic Dry Valleys) contains abundant CaCl2. These seasonal slope streaks are thought to form when CaCl2 in the soil deliquesces due to contact with atmospheric water vapor (Dickson et al., 2013). It is important to understand how this CaCl2 interacts with water vapor at low temperatures relevant to Mars and the Martian analog sites. Here we use a Raman microscope and environmental cell to monitor the low-temperature (223 - 273 K) deliquescence (solid to aqueous phase transition) and efflorescence (aqueous to solid phase transition) of three hydration states of CaCl2 (dihydrate, tetrahydrate, hexahydrate). We have found that the deliquescence relative humidity (DRH) increases with increasing hydration state, which is an expected result. Average DRH values over the temperature range studied are 20.0 × 2.6% RH for the dihydrate, 31.8 × 6.3% RH for the tetrahydrate and 60.7 × 1.6% RH for the hexahydrate. Once the aqueous solution has formed, efflorescence (recrystallization) of the salt is kinetically hindered and supersaturated solutions can exist at humidities far below the DRH. Regardless of temperature or initial hydration state of the solid salt, we do not observe efflorescence of the aqueous solutions to occur until single digit RH values are reached. We show here that calcium chloride is at least as deliquescent as many perchlorate salts, and that solutions of calcium chloride are even more difficult to recrystallize once a brine solution has formed. These experimental results will assist with interpretation of observations of deliquescence in the Antarctic Dry Valleys and will help us understand potential liquid water formation on Mars. In addition to formation of brines through melting, deliquescence of salts such as CaCl2 is a reasonable mechanism for formation of aqueous solutions on current Mars.

Effects of rinsing with arginine bicarbonate and urea solutions on initial enamel lesions in situ.

PubMed

Yu, Y; Wang, X; Ge, C; Wang, B; Cheng, C; Gan, Y-H

2017-04-01

The aim of this study was to investigate the effects of rinsing with arginine or urea solution on initial enamel lesions in situ. Fourteen subjects who wore mandibular removable partial dentures embedded with bovine enamel blocks with artificial enamel lesions were included. The experiment included four 4-week rinsing periods with a 10-day washout period between each rinsing period. In each rinsing period, the subjects rinsed after meal or snack using water, or 2% arginine bicarbonate, or 1% urea, or 0.05% NaF solution, five times daily. The mineralization changes of the enamel lesions were assessed using quantitative light-induced fluorescence. All groups except the water group showed a statistically significant decrease in the fluorescence loss after treatment, compared with their respective baseline. Although both the arginine group and urea group showed more decrease in fluorescence loss than that of the water group, the decrease was not statistically significantly different from that of the water group. The decrease in fluorescence loss of the NaF group was statistically significant than that of the water group, arginine group, and urea group. Rinsing with arginine or urea solution offers limited remineralizing benefit to enamel lesions over a period of 4-week time. © 2016 The Authors. Oral Diseases Published by John Wiley & Sons Ltd.

Effect of vitamin C concentration and co-injection with calcium chloride on beef retail display color.

PubMed

Wheeler, T L; Koohmaraie, M; Shackelford, S D

1996-08-01

The objectives of these experiments were to determine 1) the most effective vitamin C concentration to stabilize color of beef cuts during retail display and 2) the effect on color of incorporating vitamin C into a calcium chloride (CaCl2) injection solution. Top round cuts (semimembranosus and adductor) were injected with 5% by weight of a 0, .25, .5, 1, 2, or 4% sodium ascorbate solution (Exp. 1) or a 0, .5, 1, or 1.5% sodium ascorbate solution (Exp. 2). In Exp. 1, vitamin C resulted in more (P < .05) stable lean color during 9 degrees C display, and .5, 1, and 2% vitamin C were most (P < .05) effective. In Exp. 2, all concentrations of vitamin C maintained redder (P < .05) steaks after 3, 5, and 7 d of display than control steaks and had a lower (P < .05) percentage of surface discoloration after 5 and 7 d of display at 1 degree C. Experiment 3 used beef bottom round cuts (biceps femoris) to compare control, vitamin C- (1%), CaCl2-(200 mM) and vitamin C + CaCl2-treated steaks displayed at 1 degree C. Calcium chloride-treated steaks were more (P < .05) brown and had a higher (P < .05) percentage of surface discoloration on d 5 and 7 than control steaks, whereas steaks treated with vitamin C or vitamin C + CaCl2 were more (P < .05) red and had lower (P < .05) discoloration on d 5 and 7 than control steaks. Vitamin C can be injected into beef subprimals to enhance lean color stability and extend retail display life. Vitamin C also can be used in combination with CaCl2 to offset potential color deterioration, after 5 d of display, due to salt-induced oxidation.

Solubility of NaCl in aqueous electrolyte solutions from 10 to 100°C

USGS Publications Warehouse

Clynne, M.A.; Potter, R.W.; Haas, J.L.

1981-01-01

The solubilities of NaCl in aqueous KCl, MgCl2, CaCl2, and mixed CaCl2-KCl solutions have been determined from 10 to 100??C. The data were fit to an equation, and the equation was used to calculate values of the change in solubility of NaCl, ???[NaCl]/???T. These values are required for calculations of the rate of migration of fluids in a thermal gradient in rock salt. The data obtained here indicate that the values of ???[NaCl]/???T are 36-73% greater for solutions containing divalent ions than for the NaCl-H2O system.

The Influence of Carbohydrate Mouth Rinse on Self-Selected Intermittent Running Performance.

PubMed

Rollo, Ian; Homewood, George; Williams, Clyde; Carter, James; Goosey-Tolfrey, Vicky L

2015-12-01

This study investigated the influence of mouth rinsing a carbohydrate solution on self-selected intermittent variable-speed running performance. Eleven male amateur soccer players completed a modified version of the Loughborough Intermittent Shuttle Test (LIST) on 2 occasions separated by 1 wk. The modified LIST allowed the self-selection of running speeds during Block 6 of the protocol (75-90 min). Players rinsed and expectorated 25 ml of noncaloric placebo (PLA) or 10% maltodextrin solution (CHO) for 10 s, routinely during Block 6 of the LIST. Self-selected speeds during the walk and cruise phases of the LIST were similar between trials. Jogging speed was significantly faster during the CHO (11.3 ± 0.7 km · h(-1)) than during the PLA trial (10.5 ± 1.3 km · h(-1)) (p = .010); 15-m sprint speeds were not different between trials (PLA: 2.69 ± 0.18 s: CHO: 2.65 ± 0.13 s) (F(2, 10), p = .157), but significant benefits were observed for sprint distance covered (p = .024). The threshold for the smallest worthwhile change in sprint performance was set at 0.2 s. Inferential statistical analysis showed the chance that CHO mouth rinse was beneficial, negligible, or detrimental to repeated sprint performance was 86%, 10%, and 4%, respectively. In conclusion, mouth rinsing and expectorating a 10% maltodextrin solution was associated with a significant increase in self-selected jogging speed. Repeated 15-m sprint performance was also 86% likely to benefit from routinely mouth rinsing a carbohydrate solution in comparison with a taste-matched placebo.

Measurement of Setschenow constants for six hydrophobic compounds in simulated brines and use in predictive modeling for oil and gas systems.

PubMed

Burant, Aniela; Lowry, Gregory V; Karamalidis, Athanasios K

2016-02-01

Treatment and reuse of brines, produced from energy extraction activities, requires aqueous solubility data for organic compounds in saline solutions. The presence of salts decreases the aqueous solubility of organic compounds (i.e. salting-out effect) and can be modeled using the Setschenow Equation, the validity of which has not been assessed in high salt concentrations. In this study, we used solid-phase microextraction to determine Setschenow constants for selected organic compounds in aqueous solutions up to 2-5 M NaCl, 1.5-2 M CaCl2, and in Na-Ca binary electrolyte solutions to assess additivity of the constants. These compounds exhibited log-linear behavior up to these high NaCl concentrations. Log-linear decreases in solubility with increasing salt concentration were observed up to 1.5-2 M CaCl2 for all compounds, and added to a sparse database of CaCl2 Setschenow constants. Setschenow constants were additive in binary electrolyte mixtures. New models to predict CaCl2 and KCl Setschenow constants from NaCl Setschenow constants were developed, which successfully predicted the solubility of the compounds measured in this study. Overall, data show that the Setschenow Equation is valid for a wide range of salinity conditions typically found in energy-related technologies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Uptake of divalent ions (Mn+2 and Ca+2) by heat-set whey protein gels.

PubMed

Oztop, Mecit H; McCarthy, Kathryn L; McCarthy, Michael J; Rosenberg, Moshe

2012-02-01

Divalent salts are used commonly for gelation of polymer molecules. Calcium, Ca(+2), is one of the most common divalent ions that is used in whey protein gels. Manganese, Mn(+2), is also divalent, but paramagnetic, enhancing relaxation decay rates in magnetic resonance imaging (MRI) and can be used as a probe to understand the behavior of Ca(+2) in whey protein gels. The objective of this study was to investigate the diffusion of Ca(+2) and Mn(+2) ions in heat-set whey protein gels by using MRI and nuclear magnetic resonance (NMR) relaxometry. Whey protein gels were immersed in solutions containing MnCl(2) and CaCl(2) at neutral pH. Images obtained with gels immersed in MnCl(2) solution revealed a relaxation sink region in the gel's surface and the thickness of the region increased with time. These "no signal" regions in the MR images were attributed to uptake of Mn(+2) by the gel. Results obtained with CaCl(2) solution indicated that since Ca(+2) did not have the paramagnetic effect, the regions where Ca(+2) diffused into the gel exhibited a slight decrease in signal intensity. The relaxation spectrums exhibited 3 populations of protons, for gels immersed in MnCl(2) solution, and 2 populations for gels in CaCl(2) solution. No significant change in T(2) distributions was observed for the gels immersed in CaCl(2) solution. The results demonstrated that MRI and NMR relaxometry can be used to understand the diffusion of ions into the whey protein gel, which is useful for designing gels of different physical properties for controlled release applications. Design of food systems for delivery of bioactive compounds requires knowledge of diffusion rates and structure. Utilizing magnetic resonance imaging the diffusion rates of ions can be measured. Relaxation spectra could yield information concerning molecular interactions. © 2012 Institute of Food Technologists®

Cotransport of bacteria with hematite in porous media: Effects of ion valence and humic acid.

PubMed

Yang, Haiyan; Ge, Zhi; Wu, Dan; Tong, Meiping; Ni, Jinren

2016-01-01

This study investigated the influence of multiple colloids (hematite and humic acid) on the transport and deposition of bacteria (Escherichia coli) in packed porous media in both NaCl (5 mM) and CaCl2 (1 mM) solutions at pH 6. Due to the alteration of cell physicochemical properties, the presence of hematite and humic acid in cell suspensions significantly affected bacterial transport and deposition in quartz sand. Specifically, the presence of hematite (5 mg/L) decreased cell transport (increased cell deposition) in quartz sand in both NaCl and CaCl2 solutions, which could be attributed to the less negative overall zeta potentials of bacteria induced by the adsorption of positively charged hematite onto cell surfaces. The presence of a low concentration (0.1 mg/L) of humic acid in bacteria and hematite mixed suspensions reduced the adsorption of hematite onto cell surfaces, leading to increased cell transport in quartz sand in NaCl solutions, whereas, in CaCl2 solutions, the presence of 0.1 mg/L humic acid increased the formation of hematite-cell aggregates and thus decreased cell transport in quartz sand. When the concentration of humic acid was increased to 1 mg/L, enhanced cell transport was observed in both NaCl and CaCl2 solutions. The decreased adsorption of hematite onto cell surfaces as well as the competition of deposition sites on quartz sand with bacteria by the suspended humic acid contributed to the increased cell transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

Plasma clots gelled by different amounts of calcium for stem cell delivery.

PubMed

Gessmann, Jan; Seybold, Dominik; Peter, Elvira; Schildhauer, Thomas Armin; Köller, Manfred

2013-01-01

Freshly prepared autologous plasma clots may serve as a carrier matrix for expanded multipotent mesenchymal stromal cells (MSCs) or bone marrow cells. By varying the calcium concentration, plasma clots with different properties can be produced. The purpose of this in vitro study was to determine the optimal calcium concentrations for the clotting process, intra-clot cell viability, and clot lysis. Different plasma clots were prepared by adding an equal volume of RPMI1640 (with or without MSCs) to citrate plasma (either containing platelets or platelet-free). Clotting was initiated by the addition of CaCl(2) (10 g/100 ml H(2)O, 10 % solution). The final concentration of CaCl(2) ranged from 1 to 10 % by volume of plasma. Viability and distribution of the MSCs were analysed by calcein-AM/propidium iodide staining. MSC-embedded plasma clots were dissolved with trypsin (0.25 %), and recovered cells were further incubated for 1 week under cell culture conditions. The viability of MSCs embedded in clots formed by the addition of 1-8 % by volume CaCl2 was not affected by incubation of up to 1 week. In contrast, clots produced by higher volumes of CaCl(2) solutions (9-10 % by volume of plasma) showed decreased numbers of viable cells. Intra-clot cell proliferation was highest in clots produced by addition of 5 % CaCl(2) by plasma volume. Osteocalcin release was not influenced in platelet-free plasma but decreased in platelet-containing plasma. Morphological analysis of stained recovered MSCs revealed that lysis of the plasma clot did not affect cell morphology or subsequent spontaneous proliferation. Clot formation and clot stability can be controlled by changing the concentration of CaCl(2) added to plasma. The addition of 5 % CaCl(2) produced a plasma clot with optimal results for stem cell delivery.

Improved fertility in gilts and sows after artificial insemination of frozen-thawed boar semen by supplementation of semen extender with caffeine and CaCl2.

PubMed

Yamaguchi, Shoichiro; Funahashi, Hiroaki; Murakami, Tetsuya

2009-12-01

Supplementation of semen extender with caffeine and CaCl(2) for artificial insemination (AI) of fresh spermatozoa has been demonstrated to reduce recruitment of uterine polymorphonuclear leukocytes (PMNs) and the activity of phagocytosis. Here, we determined if addition of caffeine and CaCl(2) to semen extender improves the fertility of frozen-thawed boar semen. In experiment 1, gilts were cervically inseminated twice with frozen-thawed boar spermatozoa (25 x 10(8) cells per dose) suspended in Modena solution (n=7) or modified Beltsville Thawing Solution supplemented with caffeine and CaCl(2) (BCC, n=7). The gilts were slaughtered 4 h later, and their oviducts and uterine horns plus the body of the uterus were flushed to recover PMNs and non-phagocytosed spermatozoa. There was no difference in the total number of uterine PMNs between gilts inseminated with Modena solution and those inseminated with BCC (3.8 x 10(8) vs. 1.5 x 10(8) cells, respectively); however, the total number of uterine spermatozoa was higher when gilts were inseminated with BCC (40.6 x 10(6) cells) compared with those inseminated with Modena solution (1.4 x 10(6) cells, P<0.05). In experiment 2, gilts and sows were subjected to intrauterine insemination twice with frozen-thawed spermatozoa suspended (25 x 10(8) sperm per dose) in Modena (n=21) or BCC (n=21). The overall pregnancy and farrowing rates were higher in females inseminated with BCC (71.4 and 61.9%, respectively) compared with those inseminated with Modena solution (38.1 and 28.6%, respectively, P<0.05). However, no significant difference in litter size of piglets was observed between treatments (7.2 +/- 1.6 piglets for Modena solution vs. 8.2 +/- 0.9 piglets for BCC solution). In conclusion, we demonstrated that use of BCC solution for frozen-thawed boar semen produced better pregnancy and farrowing rates following AI than Modena solution, probably by reducing the phagocytosis of spermatozoa.

Alkali ocular burns in Martinique (French West Indies) Evaluation of the use of an amphoteric solution as the rinsing product.

PubMed

Merle, Harold; Donnio, Angélique; Ayeboua, Lucas; Michel, Franck; Thomas, Félix; Ketterle, Jeannine; Leonard, Christian; Josset, Patrice; Gerard, Max

2005-03-01

During the 4 years of this study, we noted 66 cases of alkali ocular burns, or approximately 16 cases per year, nearly half (45.5%) of which are due to an assault. For grade 1 and 2 burns the time elapsed to reepithelialization appears to be shorter when rinsed with Diphoterine* versus physiological solution. Comparison of the effectiveness of two rinsing solutions for emergency use: a physiological solution and an amphoteric solution (Diphoterine*, Laboratories Prevor, Valmondois, France). Description of the clinical and progressive characteristics of alkali burns treated at the University Hospital Center of Fort de France in Martinique (French West Indies). Prospective consecutive observational case series and nonrandomized comparative study. Sixty-six patients were included. The total number of burned eyes is 104. Forty-eight eyes (46%) were rinsed with physiological solution and 56 eyes (54%) with Diphoterine*. All patients benefited from an ocular rinse with 500ml of physiological solution or Diphoterine*, followed by a complete ophthalmologic exam. The ocular injuries were classified according to the Roper-Hall modification of the Hughes classification system. The same standardized therapeutic protocol was applied and adapted to the seriousness of the burn. Demographic data, time to corneal reepithelialization, final best corrected visual acuity and complications were analysed. Twenty-eight (42.4%) patients have a unilateral burn and 38 (57.6%) patients have bilateral burns. In decreasing order of frequency, the circumstances surrounding the injury are: assaults in 45.5% of cases (n=30), work-related accidents in 32% of cases (n=31), and domestic accidents in 23% of cases (n=15). For grade 1 and 2 burns the time elapsed to reepithelialization appears to be shorter when rinsed with Diphoterine* versus physiological solution (respectively): 1.9+/-1 days versus 11.1+/-1.4 days (p=10(-7)) and 5.6+/-4.9 days versus 10+/-9.2 days (p=0.02). For grade 3 and 4 burns, there are complications in 11 cases (11.6%): 8 corneal opacities and 3 perforations. This study is the first conducted in humans that takes into account the type of ocular rinse product used in the progressive follow-up study of injuries. The time elapsed to reepithelialization is shorter with Diphoterine* for grade 1 and 2 burns. There are not enough cases of grade 3 and 4 burns to make a conclusion. Diphoterine* seems very effective in terms of its mechanism of action and the experimental and clinical results.

Salt exclusion and mycorrhizal symbiosis increase tolerance to NaCl and CaCl2 salinity in ‘Siam Queen’ basil

USDA-ARS?s Scientific Manuscript database

A study was conducted to evaluate the effects of salinity on growth and nutrient uptake in basil (Ocimum basilicum L.). Plants were fertilized with a complete nutrient solution and exposed to no, low, or moderate levels of salinity from NaCl or CaCl2. Plants in the control and moderate salinity tre...

Rapid 3D Printing of Multifunctional Calcium Alginate Gel Pipes using Coaxial Jet Extruder

NASA Astrophysics Data System (ADS)

Rykaczewski, Konrad; Damle, Viraj

2014-11-01

Calcium alginate (CA) forms when solution containing sodium alginate (SA) comes in contact with a CaCl2 solution. The resulting gel is biocompatible as well as edible and is used in production of bio-scaffolds, artificial plant seeds, and edible substances. In the latter application, referred to in the culinary world as ``spherification,'' flavored liquids are mixed with the SA and dripped into CaCl2 solution to form gel encapsulated flavored ``marbles.'' Previously, crude 3D printing of CA structures has been achieved by stacking of such flavored liquid filled marbles. In turn, solid CA rods have been fabricated by properly mixing flow of the two solutions using a microfluidic device. Here we show that by using two circular cross-section coaxial nozzles to produce coaxial jets of the SA and CaCl2 solutions, liquid filled CA micro-to-mili scale gel pipes can be produced at speeds around ~ 150 mm/s. Such extrusion rate is compatible with most commercially available 3D printers, facilitating adoption of the CA pipe coaxial jet extruder. Here, the impact of inner and outer liquid properties and flow speeds on the gel pipe extrusion process is discussed. KR acknowledges startup funding from ASU.

The Influence of Serial Carbohydrate Mouth Rinsing on Power Output during a Cycle Sprint.

PubMed

Phillips, Shaun M; Findlay, Scott; Kavaliauskas, Mykolas; Grant, Marie Clare

2014-05-01

The objective of the study was to investigate the influence of serial administration of a carbohydrate (CHO) mouth rinse on performance, metabolic and perceptual responses during a cycle sprint. Twelve physically active males (mean (± SD) age: 23.1 (3.0) years, height: 1.83 (0.07) m, body mass (BM): 86.3 (13.5) kg) completed the following mouth rinse trials in a randomized, counterbalanced, double-blind fashion; 1. 8 x 5 second rinses with a 25 ml CHO (6% w/v maltodextrin) solution, 2. 8 x 5 second rinses with a 25 ml placebo (PLA) solution. Following mouth rinse administration, participants completed a 30 second sprint on a cycle ergometer against a 0.075 g·kg(-1) BM resistance. Eight participants achieved a greater peak power output (PPO) in the CHO trial, resulting in a significantly greater PPO compared with PLA (13.51 ± 2.19 vs. 13.20 ± 2.14 W·kg(-1), p < 0.05). Magnitude inference analysis reported a likely benefit (81% likelihood) of the CHO mouth rinse on PPO. In the CHO trial, mean power output (MPO) showed a trend for being greater in the first 5 seconds of the sprint and lower for the remainder of the sprint compared with the PLA trial (p > 0.05). No significant between-trials difference was reported for fatigue index, perceived exertion, arousal and nausea levels, or blood lactate and glucose concentrations. Serial administration of a CHO mouth rinse may significantly improve PPO during a cycle sprint. This improvement appears confined to the first 5 seconds of the sprint, and may come at a greater relative cost for the remainder of the sprint. Key pointsThe paper demonstrates that repeated administration of a carbohydrate mouth rinse can significantly improve peak power output during a single 30 second cycle sprint.The ergogenic effect of the carbohydrate mouth rinse may relate to the duration of exposure of the oral cavity to the mouth rinse, and associated greater stimulation of oral carbohydrate receptors.The significant increase in peak power output with the carbohydrate mouth rinse may come at a relative cost for the remainder of the sprint, evidenced by non-significantly lower mean power output and a greater fatigue index in the carbohydrate vs. placebo trial.Serial administration of a carbohydrate mouth rinse may be beneficial for sprint athletes as a method of performance enhancement that minimizes the risk of performance decrement through body mass increase and gastrointestinal disturbances associated with ingesting carbohydrate solutions.

The prevention of plaque re-growth by toothpastes and solutions containing block copolymers with and without polypeptide.

PubMed

Claydon, N C; Addy, M; Newcombe, R; Moran, J

2005-06-01

Chemicals which have a direct effect at inhibiting or reducing bacterial adherence to tooth surfaces may subsequently inhibit plaque growth and reduce gingival inflammation. This study investigated whether two anti-adherent systems could inhibit plaque re-growth in the mouth when rinsed as a solution or as a toothpaste slurry. A total of 21 subjects took part in a partially blind, seven cell cross-over study which compared the effects on plaque re-growth of a binary system containing block copolymers, a ternary system containing block copolymers and polypeptide, both used as toothpaste slurry rinses, their corresponding solution rinses, a conventional fluoride toothpaste rinse, a positive control chlorhexidine rinse and a negative water control. Following a dental prophylaxis subjects then rinsed with 10 ml of one of the test products for 1 min. twice a day over a 4-day period. Throughout each trial period the subjects were not permitted to use any other forms of oral hygiene. On the fifth day (96 h), the volunteers returned to the clinic, and plaque was assessed by (1) plaque index and (2) plaque area following disclosing with a food dye. The test phase of the trial was repeated for each agent and was followed by a 10-day "washout" period. Essentially neither of the anti-adherent systems inhibited plaque re-growth, whether administered in a toothpaste slurry or solution compared with the controls. If anything, neither of the test pastes were as effective as the marketed commercial paste (p<0.001). As expected plaque recorded following use of the chlorhexidine rinse was significantly less than that seen with any of the other rinses (p<0.001). Using this 4-day plaque re-growth model, the findings of this study failed to show any benefit in using the anti-adherent systems, either in a rinse or toothpaste, with the aim of inhibiting or reducing plaque formation.

Steady-state equation of water vapor sorption for CaCl2-based chemical sorbents and its application

PubMed Central

Zhang, Haiquan; Yuan, Yanping; Sun, Qingrong; Cao, Xiaoling; Sun, Liangliang

2016-01-01

Green CaCl2-based chemical sorbent has been widely used in sorption refrigeration, air purification and air desiccation. Methods to improve the sorption rate have been extensively investigated, but the corresponding theoretical formulations have not been reported. In this paper, a sorption system of solid-liquid coexistence is established based on the hypothesis of steady-state sorption. The combination of theoretical analysis and experimental results indicates that the system can be described by steady-state sorption process. The steady-state sorption equation, μ = (η − γT) , was obtained in consideration of humidity, temperature and the surface area. Based on engineering applications and this equation, two methods including an increase of specific surface area and adjustment of the critical relative humidity (γ) for chemical sorbents, have been proposed to increase the sorption rate. The results indicate that the CaCl2/CNTs composite with a large specific surface area can be obtained by coating CaCl2 powder on the surface of carbon nanotubes (CNTs). The composite reached sorption equilibrium within only 4 h, and the sorption capacity was improved by 75% compared with pure CaCl2 powder. Furthermore, the addition of NaCl powder to saturated CaCl2 solution could significantly lower the solution’s γ. The sorption rate was improved by 30% under the same environment. PMID:27682811

Steady-state equation of water vapor sorption for CaCl2-based chemical sorbents and its application

NASA Astrophysics Data System (ADS)

Zhang, Haiquan; Yuan, Yanping; Sun, Qingrong; Cao, Xiaoling; Sun, Liangliang

2016-09-01

Green CaCl2-based chemical sorbent has been widely used in sorption refrigeration, air purification and air desiccation. Methods to improve the sorption rate have been extensively investigated, but the corresponding theoretical formulations have not been reported. In this paper, a sorption system of solid-liquid coexistence is established based on the hypothesis of steady-state sorption. The combination of theoretical analysis and experimental results indicates that the system can be described by steady-state sorption process. The steady-state sorption equation, μ = (η - γT) , was obtained in consideration of humidity, temperature and the surface area. Based on engineering applications and this equation, two methods including an increase of specific surface area and adjustment of the critical relative humidity (γ) for chemical sorbents, have been proposed to increase the sorption rate. The results indicate that the CaCl2/CNTs composite with a large specific surface area can be obtained by coating CaCl2 powder on the surface of carbon nanotubes (CNTs). The composite reached sorption equilibrium within only 4 h, and the sorption capacity was improved by 75% compared with pure CaCl2 powder. Furthermore, the addition of NaCl powder to saturated CaCl2 solution could significantly lower the solution’s γ. The sorption rate was improved by 30% under the same environment.

Remarkably high apparent quantum yield of the overall photocatalytic H2O splitting achieved by utilizing Zn ion added Ga2O3 prepared using dilute CaCl2 solution.

PubMed

Sakata, Yoshihisa; Hayashi, Takuya; Yasunaga, Ryō; Yanaga, Nobuyuki; Imamura, Hayao

2015-08-21

Remarkably high photocatalytic activity for the overall H2O splitting, where the activity was 32 mmol h(-1) for H2 production and 16 mmol h(-1) for O2 production under irradiation from a 450 W high-pressure Hg lamp and the apparent quantum yield (AQY) was 71% under irradiation at 254 nm, was achieved by utilizing a Rh(0.5)Cr(1.5)O3(Rh; 0.5 wt%)/Zn(3 mol%)-Ga2O3 photocatalyst when Ga2O3 was prepared using dilute CaCl2 aqueous solution having a concentration of 0.001 mol l(-1).

Dynamics of water in LiCl and CaCl 2 aqueous solutions confined in silica matrices: A backscattering neutron spectroscopy study

NASA Astrophysics Data System (ADS)

Mamontov, E.; Cole, D. R.; Dai, S.; Pawel, M. D.; Liang, C. D.; Jenkins, T.; Gasparovic, G.; Kintzel, E.

2008-09-01

Backscattering neutron spectroscopy was used to probe the dynamics of water molecules in LiCl and CaCl 2 aqueous solutions confined in 2.7, 1.9, and 1.4 nm diameter pores of various silica matrices. The pore size of 2.7 nm was found to be sufficiently large for the confined liquids to exhibit characteristic traits of bulk behavior, such as a freezing-melting transition and a phase separation. On the other hand, none of the fluids in the 1.4 nm pores exhibited a clear freezing-melting transition; instead, their dynamics at low temperatures gradually became too slow for the nanosecond resolution of the experiment. The greatest suppression of water mobility was observed in the CaCl 2 solutions, which suggests that cation charge and perhaps the cation hydration environment have a profound influence on the dynamics of the water molecules. Quasielastic neutron scattering measurements of pure H 2O and 1 m LiCl-H 2O solution confined in 1.9 nm pores revealed a dynamic transition in both liquids at practically the same temperature of 225-226 K, even though the dynamics of the solution at room temperature appeared to slow down by more than an order of magnitude compared to the pure water. The observation of the dynamic transition in the solution suggests that this transition may be a universal feature of water governed by processes acting on the local scale, such as a change in the hydrogen bonding.

Effects of extraction solvent on fucose content in fucoidan extracted from brown seaweed (Sargassum sp.) from Pulau Langkawi, Kedah, Malaysia

NASA Astrophysics Data System (ADS)

Baba, Bibi Marliana; Mustapha, Wan Aida Wan; Joe, Lim Seng

2016-11-01

The objective of this study was to determine the effects of extraction solvent on the fucose content in fucoidan that had been isolated from Sargassum sp., which is a type of brown seaweed that was harvested in Pulau Langkawi, Kedah, Malaysia. There were three different solvents that were used in the extraction process in order to isolate the crude fucoidan including the hydrochloric acid, HCl, calcium chloride, CaCl2 solution and also the papain ezyme solution. Other extraction parameters that were the extraction temperature and time were fixed at three hours, at 45°C respectively. It was found that there was a significant different (p< 0.05) on the fucose content of fucoidan that had been extracted by using the enzymatic extraction (papain) with those were extracted by HCl and CaCl2 solution. However, the fucose content in fucoidan been extracted with HCl and CaCl2 solution showed no significant different (p> 0.05) amongst each other. Hence, this study indicated that the extraction of fucoidan using HCl tend to possess higher fucose content which will increase the potential of the extraction method to be used in the industries such as pharmaceuticals as well as the nutraceuticals.

Efficacy of home washing methods in controlling surface microbial contamination on fresh produce.

PubMed

Kilonzo-Nthenge, Agnes; Chen, Fur-Chi; Godwin, Sandria L

2006-02-01

Much effort has been focused on sanitation of fresh produce at the commercial level; however, few options are available to the consumer. The purpose of this study was to determine the efficacy of different cleaning methods in reducing bacterial contamination on fresh produce in a home setting. Lettuce, broccoli, apples, and tomatoes were inoculated with Listeria innocua and then subjected to combinations of the following cleaning procedures: (i) soak for 2 min in tap water, Veggie Wash solution, 5% vinegar solution, or 13% lemon solution and (ii) rinse under running tap water, rinse and rub under running tap water, brush under running tap water, or wipe with wet/dry paper towel. Presoaking in water before rinsing significantly reduced bacteria in apples, tomatoes, and lettuce, but not in broccoli. Wiping apples and tomatoes with wet or dry paper towel showed lower bacterial reductions compared with soaking and rinsing procedures. Blossom ends of apples were more contaminated than the surface after soaking and rinsing; similar results were observed between flower section and stem of broccoli. Reductions of L. innocua in both tomatoes and apples (2.01 to 2.89 log CFU/g) were more than in lettuce and broccoli (1.41 to 1.88 log CFU/g) when subjected to same washing procedures. Reductions of surface contamination of lettuce after soaking in lemon or vinegar solutions were not significantly different (P > 0.05) from lettuce soaking in cold tap water. Therefore, educators and extension workers might consider it appropriate to instruct consumers to rub or brush fresh produce under cold running tap water before consumption.

Mouth Rinsing with Maltodextrin Solutions Fails to Improve Time Trial Endurance Cycling Performance in Recreational Athletes.

PubMed

Kulaksız, Tuğba Nilay; Koşar, Şükran Nazan; Bulut, Suleyman; Güzel, Yasemin; Willems, Marcus Elisabeth Theodorus; Hazir, Tahir; Turnagöl, Hüseyin Hüsrev

2016-05-09

The carbohydrate (CHO) concentration of a mouth rinsing solution might influence the CHO sensing receptors in the mouth, with consequent activation of brain regions involved in reward, motivation and regulation of motor activity. The purpose of the present study was to examine the effects of maltodextrin mouth rinsing with different concentrations (3%, 6% and 12%) after an overnight fast on a 20 km cycling time trial performance. Nine recreationally active, healthy males (age: 24 ± 2 years; V ˙ O 2 m a x : 47 ± 5 mL·kg(-1)·min(-1)) participated in this study. A double-blind, placebo-controlled randomized study was conducted. Participants mouth-rinsed every 2.5 km for 5 s. Maltodextrin mouth rinse with concentrations of 3%, 6% or 12% did not change time to complete the time trial and power output compared to placebo (p > 0.05). Time trial completion times were 40.2 ± 4.0, 40.1 ± 3.9, 40.1 ± 4.4, and 39.3 ± 4.2 min and power output 205 ± 22, 206 ± 25, 210 ± 24, and 205 ± 23 W for placebo, 3%, 6%, and 12% maltodextrin conditions, respectively. Heart rate, lactate, glucose, and rating of perceived exertion did not differ between trials (p > 0.05). In conclusion, mouth rinsing with different maltodextrin concentrations after an overnight fast did not affect the physiological responses and performance during a 20 km cycling time trial in recreationally active males.

Multisite Ion Model in Concentrated Solutions of Divalent Cations (MgCl2 and CaCl2): Osmotic Pressure Calculations

PubMed Central

2015-01-01

Accurate force field parameters for ions are essential for meaningful simulation studies of proteins and nucleic acids. Currently accepted models of ions, especially for divalent ions, do not necessarily reproduce the right physiological behavior of Ca2+ and Mg2+ ions. Saxena and Sept (J. Chem. Theor. Comput.2013, 9, 3538–3542) described a model, called the multisite-ion model, where instead of treating the ions as an isolated sphere, the charge was split into multiple sites with partial charge. This model provided accurate inner shell coordination of the ion with biomolecules and predicted better free energies for proteins and nucleic acids. Here, we expand and refine the multisite model to describe the behavior of divalent ions in concentrated MgCl2 and CaCl2 electrolyte solutions, eliminating the unusual ion–ion pairing and clustering of ions which occurred in the original model. We calibrate and improve the parameters of the multisite model by matching the osmotic pressure of concentrated solutions of MgCl2 to the experimental values and then use these parameters to test the behavior of CaCl2 solutions. We find that the concentrated solutions of both divalent ions exhibit the experimentally observed behavior with correct osmotic pressure, the presence of solvent separated ion pairs instead of direct ion pairs, and no aggregation of ions. The improved multisite model for (Mg2+ and Ca2+) can be used in classical simulations of biomolecules at physiologically relevant salt concentrations. PMID:25482831

Effect of the pore water composition on the diffusive anion transport in argillaceous, low permeability sedimentary rocks

NASA Astrophysics Data System (ADS)

Wigger, Cornelia; Van Loon, Luc R.

2018-06-01

The effect of the pore water composition on the diffusive anion transport was studied for two different argillaceous, low permeability sedimentary rocks, Opalinus Clay (OPA) and Helvetic Marl (HM). The samples were saturated with different solutions with varying molar concentration and different main cations in the solution: NaCl based pore solutions and CaCl2 based pore solutions. The total porosity was measured by through-diffusion experiments with the neutral tracer HTO. Experiments performed in NaCl solutions resulted in a porosity of 0.12 for OPA and 0.03 for HM, and are consistent with results of the experiments in CaCl2 solutions. The total porosity was independent of the molar concentration, in contrast to the measured anion porosity, which increased with increasing molar concentration. It could further be observed that the pore solution based on the bivalent cation calcium shielded the negative surface charge stronger than the monovalent cation sodium, resulting in a larger measureable anion-accessible porosity in the case of CaCl2 solutions. The data was modelled based on an adapted Donnan approach of Birgersson and Karnland (2009). The model had to be adjusted with a permanent free, uncharged porosity, as well as with structural information on the permanent anion exclusion because of so-called bottleneck pores. Both parameters can only be evaluated from experiments. Nevertheless, taking these two adaptions into account, the effect of varying pore water compositions on the anion-accessible porosity of the investigated argillaceous rocks could be satisfactorily described.

Effect of the pore water composition on the diffusive anion transport in argillaceous, low permeability sedimentary rocks.

PubMed

Wigger, Cornelia; Van Loon, Luc R

2018-06-01

The effect of the pore water composition on the diffusive anion transport was studied for two different argillaceous, low permeability sedimentary rocks, Opalinus Clay (OPA) and Helvetic Marl (HM). The samples were saturated with different solutions with varying molar concentration and different main cations in the solution: NaCl based pore solutions and CaCl 2 based pore solutions. The total porosity was measured by through-diffusion experiments with the neutral tracer HTO. Experiments performed in NaCl solutions resulted in a porosity of 0.12 for OPA and 0.03 for HM, and are consistent with results of the experiments in CaCl 2 solutions. The total porosity was independent of the molar concentration, in contrast to the measured anion porosity, which increased with increasing molar concentration. It could further be observed that the pore solution based on the bivalent cation calcium shielded the negative surface charge stronger than the monovalent cation sodium, resulting in a larger measureable anion-accessible porosity in the case of CaCl 2 solutions. The data was modelled based on an adapted Donnan approach of Birgersson and Karnland (2009). The model had to be adjusted with a permanent free, uncharged porosity, as well as with structural information on the permanent anion exclusion because of so-called bottleneck pores. Both parameters can only be evaluated from experiments. Nevertheless, taking these two adaptions into account, the effect of varying pore water compositions on the anion-accessible porosity of the investigated argillaceous rocks could be satisfactorily described. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of a new pre-brushing rinse on dental plaque removal.

PubMed

Vouros, J; Sakellari, D; Konstantinidis, A

1994-11-01

Non-prescription prebrushing rinses to facilitate dental plaque removal have been advertised in recent years. The purpose of the present study was to determine the plaque removal effectiveness of Plax (Colgate) prebrushing rinse by comparing it to a placebo solution. 19 dental students volunteered for this double blind study which consisted of 2 experimental periods. The following procedure was followed: 3 weeks after scaling and polishing, the participants abstained from oral hygiene for 3 days to allow dental plaque to accumulate. After plaque disclosing, the 4 mandibular incisors were photographed using a strictly defined technique, as described by Quirynen et al. Then the volunteers mouthrinsed for 30 s with 15 ml of a solution provided to them. Neither the volunteers nor the examiners knew which solution (test or control) was used. After mouthrinsing, the participants were allowed to brush their teeth and the remaining plaque was photographed again. During the 2nd experimental period, the same procedure was followed, and the 2nd solution was used for mouthrinsing. The effectiveness of the solutions was evaluated by comparing the proportion of dental plaque removed during the 2 experimental periods. The area of dental plaque was measured by an electronic high-precision device (planimeter). The proportion of plaque removed after rinsing with Plax was 0.40 +/- 0.23 and after rising with placebo 0.42 +/- 0.24, of the tooth surface (p = 0.962). Analysis of data by means of paired t-test between the 2 experimental periods revealed no beneficial effect regarding plaque removal when Plax was used.

Chemical sterilisation of animals: A review of the use of zinc- and CaCl2 based solutions in male and female animals and factors likely to improve responses to treatment.

PubMed

Cavalieri, John

2017-06-01

Chemical sterilisation can be used as an alternative to surgical castration in some circumstances. This review focuses on responses to treatment with zinc- or CaCl 2 -based chemosterilants, factors that have affected treatments and their potential use to sterilise female cattle. Successful treatment with a low incidence of adverse side effects in male animals has occurred with the use of zinc gluconate (ZG), neutralised in arginine and a 20% solution of CaCl 2 in ethanol. Injection technique plays an important role in success. Less satisfactory results appear to occur following use in animals with relatively larger testes. In animals with relatively small testes adjustment of the dose according to testicular size appears to optimise results. The techniques appear to be most suited to population control strategies in companion animals where low cost treatment of animals in environments where surgical facilities and specialised aftercare are lacking. The need for careful administration and likely slower speed of administration compared to surgical castration are likely to hamper application within the cattle industries. Recently transvaginal, intraovarian administration of CaCl 2 in ethanol has been shown to cause complete ovarian atrophy without apparent pain in some heifers, although variable responses were found. Chemical sterilisation can play a role in the sterilisation of animals but careful attention to dose, volume, chemical composition, administration technique are needed to avoid adverse side effects and variability in responses associated with some treatments. Application in female animals requires further study but CaCl 2 in ethanol can potentially cause complete ovarian atrophy when administered to heifers. Copyright © 2017 Elsevier B.V. All rights reserved.

Sample treatment optimization for fish stool metabolomics.

PubMed

Hano, Takeshi; Ito, Mana; Ito, Katsutoshi; Uchida, Motoharu

2018-06-07

Gut microbiota play an essential role in an organism's health. The fecal metabolite profiling content reflects these microbiota-mediated physiological changes in various organisms, including fish. Therefore, metabolomics analysis of fish feces should provide insight into the dynamics linking physiology and gut microbiota. However, metabolites are often unstable in aquatic environments, making fecal metabolites difficult to examine in fish. In this study, a novel method using gas chromatography-mass spectrometry (GC-MS) was developed and optimized for the preparation of metabolomics samples from the feces of the marine fish, red sea bream (Pagrus major). The preparation methodology was optimized, focusing on rinsing frequency and rinsing solvent. Feces (collected within 4 h of excretion) were rinsed three times with sterilized 2.5% NaCl solution or 3.0% artificial seawater (ASW). Among the 86 metabolites identified in the NaCl-rinsed samples, 57 showed superior recovery to that in ASW-rinsed samples, indicating that NaCl is a better rinsing solvent, particularly for amino acids, organic acids, and fatty acids. To evaluate rinsing frequency, fecal samples were rinsed with NaCl solution 0, 1, 3, or 5 times. The results indicate that three or more rinses enabled robust and stable detection of metabolites encapsulated within the solid fecal residue. Furthermore, these data suggest that rinsing is unnecessary when studying sugars, amino acids, and sterols, again highlighting the need for appropriate rinsing solvent and frequency. This study provides further insight into the use of fecal samples to evaluate and promote fish health during farming and supports the application of this and similar analyses to study the effects of environmental fluctuations and/or contamination. Copyright © 2018 Elsevier B.V. All rights reserved.

Role of Reverse Divalent Cation Diffusion in Forward Osmosis Biofouling.

PubMed

Xie, Ming; Bar-Zeev, Edo; Hashmi, Sara M; Nghiem, Long D; Elimelech, Menachem

2015-11-17

We investigated the role of reverse divalent cation diffusion in forward osmosis (FO) biofouling. FO biofouling by Pseudomonas aeruginosa was simulated using pristine and chlorine-treated thin-film composite polyamide membranes with either MgCl2 or CaCl2 draw solution. We related FO biofouling behavior-water flux decline, biofilm architecture, and biofilm composition-to reverse cation diffusion. Experimental results demonstrated that reverse calcium diffusion led to significantly more severe water flux decline in comparison with reverse magnesium permeation. Unlike magnesium, reverse calcium permeation dramatically altered the biofilm architecture and composition, where extracellular polymeric substances (EPS) formed a thicker, denser, and more stable biofilm. We propose that FO biofouling was enhanced by complexation of calcium ions to bacterial EPS. This hypothesis was confirmed by dynamic and static light scattering measurements using extracted bacterial EPS with the addition of either MgCl2 or CaCl2 solution. We observed a dramatic increase in the hydrodynamic radius of bacterial EPS with the addition of CaCl2, but no change was observed after addition of MgCl2. Static light scattering revealed that the radius of gyration of bacterial EPS with addition of CaCl2 was 20 times larger than that with the addition of MgCl2. These observations were further confirmed by transmission electron microscopy imaging, where bacterial EPS in the presence of calcium ions was globular, while that with magnesium ions was rod-shaped.

IMPACT OF A RINSE STEP ON PROTEIN REMOVAL FROM SILICONE HYDROGEL CONTACT LENSES

PubMed Central

Pucker, Andrew D.; Nichols, Jason J.

2010-01-01

PURPOSE To determine the impact of the rinse step in “no rub” contact lens care systems relative to its ability to assist in removing loosely associated and bound tear film proteins from a worn silicone hydrogel lens. METHODS After informed consent, subjects were fitted with lotrafilcon B contact lenses (CIBA Vision, Inc). If the fit was acceptable, subjects were asked to wear the lenses on a daily wear basis for 5 (+2, −0) days for an outcome visit. Subjects were instructed to use AQuify Multi-Purpose Disinfecting Solution (CIBA Vision, Inc) following the manufacturer's “no rub” instructions. At the outcome visit, contact lenses were then collected by a gloved examiner, with a sterile metal forceps, who rinsed the right lens but did not rinse the left lens upon removal from the eyes. Protein was extracted with a 50:50 0.2% trifluoroacetic acid-acetonitrile solution and quantified using a Bradford analyses. RESULTS Twenty contact lens wearers were enrolled in this study. For the non-rinsed lenses, the first extraction yielded 13.4 ± 9.2 µg/lens of protein, while the second extraction yielded 5.8 ± 2.8 µg/lens of protein. For the rinsed lenses, first extraction yielded an average of 3.0 ± 1.9 µg/lens of protein, while the second extraction yielded an average of 4.0 ± 2.3 µg/lens. Repeated measures ANOVA showed a significant interaction (F-statistic = 18.9, p< 0.0001) between the rinse of a lens and extraction number. CONCLUSIONS Rinsing a contact lens following removal from the eye removes well over one-half of the protein associated with it. Further, in order to biochemically recover all protein from a silicone hydrogel lens, it may be important to perform more than one chemical extraction from it. PMID:19609231

Molecular dynamics simulation, ab initio calculation, and size-selected anion photoelectron spectroscopy study of initial hydration processes of calcium chloride

NASA Astrophysics Data System (ADS)

He, Zhili; Feng, Gang; Yang, Bin; Yang, Lijiang; Liu, Cheng-Wen; Xu, Hong-Guang; Xu, Xi-Ling; Zheng, Wei-Jun; Gao, Yi Qin

2018-06-01

To understand the initial hydration processes of CaCl2, we performed molecular simulations employing the force field based on the theory of electronic continuum correction with rescaling. Integrated tempering sampling molecular dynamics were combined with ab initio calculations to overcome the sampling challenge in cluster structure search and refinement. The calculated vertical detachment energies of CaCl2(H2O)n- (n = 0-8) were compared with the values obtained from photoelectron spectra, and consistency was found between the experiment and computation. Separation of the Cl—Ca ion pair is investigated in CaCl2(H2O)n- anions, where the first Ca—Cl ionic bond required 4 water molecules, and both Ca—Cl bonds are broken when the number of water molecules is larger than 7. For neutral CaCl2(H2O)n clusters, breaking of the first Ca—Cl bond starts at n = 5, and 8 water molecules are not enough to separate the two ion pairs. Comparing with the observations on magnesium chloride, it shows that separating one ion pair in CaCl2(H2O)n requires fewer water molecules than those for MgCl2(H2O)n. Coincidentally, the solubility of calcium chloride is higher than that of magnesium chloride in bulk solutions.

Hydrothermal calcium modification of 316L stainless steel and its apatite forming ability in simulated body fluid.

PubMed

Valanezahad, Alireza; Ishikawa, Kunio; Tsuru, Kanji; Maruta, Michito; Matsuya, Shigeki

2011-01-01

To understand the feasibility of calcium (Ca) modification of type 316L stainless steel (316L SS) surface using hydrothermal treatment, 316L SS plates were treated hydrothermally in calcium chloride (CaCl(2)) solution. X-ray photoelectron spectroscopic analysis revealed that the surface of 316L SS plate was modified with Ca after hydrothermal treatment at 200°C. And the immobilized Ca increased with CaCl(2) concentration. However no Ca-modification was occurred for 316L SS plates treated at 100°C. When Ca-modified 316L SS plate was immersed in simulated body fluid (SBF) with ion concentrations nearly equal to those of human blood plasma, low crystalline apatite was precipitated on its surface whereas no precipitate was observed on non Ca-modified 316L SS. The results obtained in the present study indicated that hydrothermal treatment at 200°C in CaCl(2) solution is useful for Ca-modification of 316L SS, and Ca-modification plays important role for apatite precipitation in SBF.

Preparation and characterization of silk fibroin as a biomaterial with potential for drug delivery

PubMed Central

2012-01-01

Background Degummed silk fibroin from Bombyx mori (silkworm) has potential carrier capabilities for drug delivery in humans; however, the processing methods have yet to be comparatively analyzed to determine the differential effects on the silk protein properties, including crystalline structure and activity. Methods In this study, we treated degummed silk with four kinds of calcium-alcohol solutions, and performed secondary structure measurements and enzyme activity test to distinguish the differences between the regenerated fibroins and degummed silk fibroin. Results Gel electrophoresis analysis revealed that Ca(NO3)2-methanol, Ca(NO3)2-ethanol, or CaCl2-methanol treatments produced more lower molecular weights of silk fibroin than CaCl2-ethanol. X-ray diffraction and Fourier-transform infrared spectroscopy showed that CaCl2-ethanol produced a crystalline structure with more silk I (α-form, type II β-turn), while the other treatments produced more silk II (β-form, anti-parallel β-pleated sheet). Solid-State 13C cross polarization and magic angle spinning-nuclear magnetic resonance measurements suggested that regenerated fibroins from CaCl2-ethanol were nearly identical to degummed silk fibroin, while the other treatments produced fibroins with significantly different chemical shifts. Finally, enzyme activity test indicated that silk fibroins from CaCl2-ethanol had higher activity when linked to a known chemotherapeutic drug, L-asparaginase, than the fibroins from other treatments. Conclusions Collectively, these results suggest that the CaCl2-ethanol processing method produces silk fibroin with biomaterial properties that are appropriate for drug delivery. PMID:22676291

Improving tenderness of normal and callipyge lambs with calcium chloride.

PubMed

Clare, T L; Jackson, S P; Miller, M F; Elliott, C T; Ramsey, C B

1997-02-01

Effects of CaCl2 injection on meat quality traits of 10 normal and 10 callipyge phenotype crossbred lambs were studied. Primal cuts from one side of each carcass served as the control and cuts from the other side were injected. After storage for 14 d at 2 degrees C, chops were evaluated by Warner-Bratzler shear (WBS) force, trained sensory panel, and consumer sensory panel. Treatment of the muscles with 200 mM CaCl2 increased (P < .05) tenderness and lamb flavor intensity scores by the trained sensory panel and decreased (P < .05) WBS force in both normal and callipyge phenotypes. When callipyge muscles were not injected, consumers rated 94% of leg chops, 60% of loin chops, and 89.4% of shoulder chops acceptable in tenderness. However, when callipyge muscles were CaCl2-injected, consumers rated 96.5% of leg chops, 85.4% of loin chips, and 93.5% of shoulder chops acceptable in tenderness. Normal phenotype carcasses had more marbling (P < .05) in a firmer, finer-textured, brighter cherry red longissimus muscle. Injection of CaCl2 did not affect visual lean color or L, a or b values during retail display of the chops. However, CaCl2 injection decreased color uniformity, increased discoloration, and increased browning at d 2. Therefore, a 5% (wt/wt) injection of 200 mM CaCl2 solution can be applied to improve normal and callipyge lamb tenderness and reduce tenderness and juiciness variation without detrimental effects on other palatability traits when evaluated by trained sensory panelists or consumers.

Polymeric Mold For Providing A Microscale Part

DOEpatents

Boehme, Dale R.; Bankert, Michelle A.; Christenson, Todd R.

2005-01-11

The invention is a developer system for developing a PMMA photoresist having exposed patterns comprising features having both very small sizes, and very high aspect ratios. The developer system of the present invention comprises a developer tank, an intermediate rinse tank and a final rinse tank, each tank having a source of high frequency sonic agitation, temperature control, and continuous filtration. It has been found that by moving a patterned wafer, through a specific sequence of developer/rinse solutions, where an intermediate rinse solution completes development of those portions of the exposed resist left undeveloped after the development solution, by agitating the solutions with a source of high frequency sonic vibration, and by adjusting and closely controlling the temperatures and continuously filtering and recirculating these solutions, it is possible to maintain the kinetic dissolution of the exposed PMMA polymer as the rate limiting step.

Optical coherence tomography analysis of hydrofluoric acid decontamination of human cornea by mannitol solution.

PubMed

Nosé, Ricardo M; Daga, Fabio B; Nosé, Walton; Kasahara, Niro

2017-03-01

To evaluate the efficacy of mannitol solution as a decontamination agent on the chemical burn of the human corneas. Eight donor corneas from an eye bank were exposed to 25μl of 2.5% hydrofluoric acid (HF) solution on a filter paper for 20s. Three eyes were rinsed with 1000ml of mannitol 20% for 15min immediately after removal of the filter paper, 3 other were rinsed with sodium chloride (NaCl) 0.9% (1000ml for 15min) and two eyes were not rinsed. Microstructural changes were monitored in the time domain by optical coherence tomography (OCT) imaging for 75min. NaCl reduced the penetration depth to approximately half the thickness of the cornea at 15min; scattering within the anterior cornea was higher than that for the unrinsed eye. With mannitol, no increased scattering was observed in the posterior part of the corneal stroma within a time period of 1h after rinsing. OCT images revealed low-scattering intensity within the anterior stroma at the end of the rinsing period. In eye bank human corneas, mannitol proved to be an efficient agent to decontaminate HF burn. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Organic-Silica Interactions in Saline: Elucidating the Structural Influence of Calcium in Low-Salinity Enhanced Oil Recovery.

PubMed

Desmond, J L; Juhl, K; Hassenkam, T; Stipp, S L S; Walsh, T R; Rodger, P M

2017-09-08

Enhanced oil recovery using low-salinity solutions to sweep sandstone reservoirs is a widely-practiced strategy. The mechanisms governing this remain unresolved. Here, we elucidate the role of Ca 2+ by combining chemical force microscopy (CFM) and molecular dynamics (MD) simulations. We probe the influence of electrolyte composition and concentration on the adsorption of a representative molecule, positively-charged alkylammonium, at the aqueous electrolyte/silica interface, for four electrolytes: NaCl, KCl, MgCl 2 , and CaCl 2 . CFM reveals stronger adhesion on silica in CaCl 2 compared with the other electrolytes, and shows a concentration-dependent adhesion not observed for the other electrolytes. Using MD simulations, we model the electrolytes at a negatively-charged amorphous silica substrate and predict the adsorption of methylammonium. Our simulations reveal four classes of surface adsorption site, where the prevalence of these sites depends only on CaCl 2 concentration. The sites relevant to strong adhesion feature the O - silica site and Ca 2+ in the presence of associated Cl - , which gain prevalence at higher CaCl 2 concentration. Our simulations also predict the adhesion force profile to be distinct for CaCl 2 compared with the other electrolytes. Together, these analyses explain our experimental data. Our findings indicate in general how silica wettability may be manipulated by electrolyte concentration.

Reliable solution processed planar perovskite hybrid solar cells with large-area uniformity by chloroform soaking and spin rinsing induced surface precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chern, Yann-Cherng; Wu, Hung-Ruei; Chen, Yen-Chu

2015-08-15

A solvent soaking and rinsing method, in which the solvent was allowed to soak all over the surface followed by a spinning for solvent draining, was found to produce perovskite layers with high uniformity on a centimeter scale and with much improved reliability. Besides the enhanced crystallinity and surface morphology due to the rinsing induced surface precipitation that constrains the grain growth underneath in the precursor films, large-area uniformity with film thickness determined exclusively by the rotational speed of rinsing spinning for solvent draining was observed. With chloroform as rinsing solvent, highly uniform and mirror-like perovskite layers of area asmore » large as 8 cm × 8 cm were produced and highly uniform planar perovskite solar cells with power conversion efficiency of 10.6 ± 0.2% as well as much prolonged lifetime were obtained. The high uniformity and reliability observed with this solvent soaking and rinsing method were ascribed to the low viscosity of chloroform as well as its feasibility of mixing with the solvent used in the precursor solution. Moreover, since the surface precipitation forms before the solvent draining, this solvent soaking and rinsing method may be adapted to spinless process and be compatible with large-area and continuous production. With the large-area uniformity and reliability for the resultant perovskite layers, this chloroform soaking and rinsing approach may thus be promising for the mass production and commercialization of large-area perovskite solar cells.« less

Tomato type and post-treatment water rinse affect efficacy of acid washes against Salmonella enterica inoculated on stem scars of tomatoes and product quality.

PubMed

Fan, Xuetong; Gurtler, Joshua B; Sokorai, Kimberly J B

2018-09-02

A study was conducted to evaluate the effects of post-treatment rinsing with water on the inactivation efficacy of acid treatments against Salmonella inoculated onto stem scar areas of two types of tomatoes. In addition, impact on fruit quality was investigated during 21 days post-treatment storage at 10 °C. A four-strain cocktail of Salmonella enterica (S. Montevideo, S. Newport, S. Saintpaul, and S. Typhimurium) was inoculated onto stem scar areas of grape and large round tomatoes. The inoculated fruits were then treated for 2 min with the following solutions: water, 2% lactic acid +2% acetic acid +2% levulinic acid, 1.7% lactic acid +1.7% acetic acid +1.7% levulinic acid, and 3% lactic acid +3% acetic acid. After treatments, half of the fruits were rinsed with water while another half were not rinsed. Non-inoculated grape tomatoes for quality analysis were treated with the same solutions with and without subsequent water rinse. Results demonstrated that the acid combinations reduced populations of Salmonella enterica on the stem scar area of grape tomatoes by 1.52-1.90 log CFU/fruit, compared with the non-treated control while water wash and rinse removed the bacterium by only 0.23-0.30 log CFU/fruit. On the stem scar of large round tomatoes, the same acid treatments achieved 3.54 log CFU/fruit reduction of the pathogen. The varying response to the acid washes between grape and large round tomatoes seems to be related to the differences in surface characteristics of stem scar areas observed with SEM. Rinsing with water after acid combination treatments did not significantly affect the efficacy of the treatments in either grape or large round tomatoes. Acidic off-odor was detected on fruits treated with acid combination without water rinse 1 day after treatment while water rinse eliminated the off-odor. The acid treatments with and without water rinse did not consistently affect appearance, color, firmness, or lycopene or ascorbic acid contents of tomatoes during 21-days storage at 10 °C. Considering the similarity in antimicrobial efficacy between the fruits with and without water rinse following acid treatments, and the elimination of acidic odor by water rinse, fruits should be rinsed with water after acid treatments. Overall, our results demonstrated that the acids were more effective in inactivating Salmonella on large round tomatoes than on grape tomatoes, and water rinses following acid treatments eliminated the acidic odor without affecting the efficacy of the acids against Salmonella. Published by Elsevier B.V.

γ-Aminobutyric acid (GABA) oral rinse reduces capsaicin-induced burning mouth pain sensation: An experimental quantitative sensory testing study in healthy subjects.

PubMed

Zhang, Y; Wang, K; Arendt-Nielsen, L; Cairns, B E

2018-02-01

In burning mouth patients, analgesia after oral administration of clonazepam may result from modulation of peripheral γ-aminobutyric acid (GABA) receptors. The effect of oral administration of test solutions (water, 0.5 mol/L or 0.05 mol/L GABA, 1% lidocaine) was investigated for the amelioration of pain and sensitivity induced by application of capsaicin (1%, 2 min) to the tongue of thirty healthy male and female subjects in this four-session, randomized, placebo-controlled, double-blinded, cross-over study. Intra-oral quantitative sensory testing was used to assess cold (CDT), warm (WDT) and mechanical (MDT) detection thresholds as well as mechanical (MPT) and heat (HPT) pain thresholds. Capsaicin-induced pain intensity was continuously rated on a 0-10 electronic visual analogue scale (VAS). The area under the VAS curve (VASAUC) after rinsing was calculated for each solution. Capsaicin application on the tongue evoked burning pain with a peak of 4.8/10, and significantly increased CDT and MDT while significantly decreasing WDT, HPT, and MPT. The VASAUC was significantly smaller after oral rinse with 0.05 mol/L GABA, 0.5 mol/L GABA, and 1% lidocaine than after oral rinse with water. Rinse with 0.5 mol/L or 0.05 mol/L GABA were similarly effective in decreasing VASAUC. Rinsing with either 1% lidocaine, 0.5 mol/L or 0.05 mol/L GABA also significantly attenuated the effects of capsaicin on WDT and HPT in a treatment independent manner. There were no sex-related differences in these effects of GABA. Capsaicin-induced burning tongue pain and decreases in WDT and HPT can be ameliorated by rinsing the mouth with lidocaine and GABA solutions. Rinsing the mouth with an oral GABA containing solution ameliorated burning pain and increased heat sensitivity produced by application of capsaicin to the tongue. This finding suggests that GABA can act as a local analgesic agent in the oral cavity. © 2017 European Pain Federation - EFIC®.

Molecular dynamics study of structure and vibrational spectra at zwitterionoic lipid/aqueous KCl, NaCl, and CaCl2 solution interfaces

NASA Astrophysics Data System (ADS)

Ishiyama, Tatsuya; Shirai, Shinnosuke; Okumura, Tomoaki; Morita, Akihiro

2018-06-01

Molecular dynamics (MD) simulations of KCl, NaCl, and CaCl2 solution/dipalmytoylphosphatidylcholine lipid interfaces were performed to analyze heterodyne-detected vibrational sum frequency generation (HD-VSFG) spectra in relation to the interfacial water structure. The present MD simulation well reproduces the experimental spectra and elucidates a specific cation effect on the interfacial structure. The K+, Na+, and Ca2+ cation species penetrate in the lipid layer more than the anions in this order, due to the electrostatic interaction with negative polar groups of lipid, and the electric double layer between the cations and anions cancels the intrinsic orientation of water at the water/lipid interface. These mechanisms explain the HD-VSFG spectrum of the water/lipid interface and its spectral perturbation by adding the ions. The lipid monolayer reverses the order of surface preference of the cations at the solution/lipid interface from that at the solution/air interface.

Handwashing and Ebola virus disease outbreaks: A randomized comparison of soap, hand sanitizer, and 0.05% chlorine solutions on the inactivation and removal of model organisms Phi6 and E. coli from hands and persistence in rinse water.

PubMed

Wolfe, Marlene K; Gallandat, Karin; Daniels, Kyle; Desmarais, Anne Marie; Scheinman, Pamela; Lantagne, Daniele

2017-01-01

To prevent Ebola transmission, frequent handwashing is recommended in Ebola Treatment Units and communities. However, little is known about which handwashing protocol is most efficacious. We evaluated six handwashing protocols (soap and water, alcohol-based hand sanitizer (ABHS), and 0.05% sodium dichloroisocyanurate, high-test hypochlorite, and stabilized and non-stabilized sodium hypochlorite solutions) for 1) efficacy of handwashing on the removal and inactivation of non-pathogenic model organisms and, 2) persistence of organisms in rinse water. Model organisms E. coli and bacteriophage Phi6 were used to evaluate handwashing with and without organic load added to simulate bodily fluids. Hands were inoculated with test organisms, washed, and rinsed using a glove juice method to retrieve remaining organisms. Impact was estimated by comparing the log reduction in organisms after handwashing to the log reduction without handwashing. Rinse water was collected to test for persistence of organisms. Handwashing resulted in a 1.94-3.01 log reduction in E. coli concentration without, and 2.18-3.34 with, soil load; and a 2.44-3.06 log reduction in Phi6 without, and 2.71-3.69 with, soil load. HTH performed most consistently well, with significantly greater log reductions than other handwashing protocols in three models. However, the magnitude of handwashing efficacy differences was small, suggesting protocols are similarly efficacious. Rinse water demonstrated a 0.28-4.77 log reduction in remaining E. coli without, and 0.21-4.49 with, soil load and a 1.26-2.02 log reduction in Phi6 without, and 1.30-2.20 with, soil load. Chlorine resulted in significantly less persistence of E. coli in both conditions and Phi6 without soil load in rinse water (p<0.001). Thus, chlorine-based methods may offer a benefit of reducing persistence in rinse water. We recommend responders use the most practical handwashing method to ensure hand hygiene in Ebola contexts, considering the potential benefit of chlorine-based methods in rinse water persistence.

Effect of ca2+ to salicylic acid release in pectin based controlled drug delivery system

NASA Astrophysics Data System (ADS)

Kistriyani, L.; Wirawan, S. K.; Sediawan, W. B.

2016-01-01

Wastes from orange peel are potentially be utilized to produce pectin, which are currently an import commodity. Pectin can be used in making edible film. Edible films are potentially used as a drug delivery system membrane after a tooth extraction. Drug which is used in the drug delivery system is salicylic acid. It is an antiseptic. In order to control the drug release rate, crosslinking process is added in the manufacturing of membrane with CaCl2.2H2O as crosslinker. Pectin was diluted in water and mixed with a plasticizer and CaCl2.2H2O solution at 66°C to make edible film. Then the mixture was dried in an oven at 50 °C. After edible film was formed, it was coated using plasticizer and CaCl2.2H2O solution with various concentration 0, 0.015, 0.03 and 0.05g/mL. This study showed that the more concentration of crosslinker added, the slower release of salicylic acid would be. This was indicated by the value of diffusivites were getting smaller respectively. The addition of crosslinker also caused smaller gels swelling value,which made the membrane is mechanically stronger

A comparison of regimen methods for the removal and inactivation of bacteria, fungi and Acanthamoeba from two types of silicone hydrogel lenses.

PubMed

Kilvington, Simon; Lonnen, James

2009-04-01

To compare the antimicrobial efficacy of commercial contact lens solutions when used according to the manufacturers' recommended regimens with two types of silicone hydrogel lenses. Four multipurpose contact lens care solutions were examined, representing manufacturer recommended regimens of "rub & rinse", "no rub, rinse" or "no rub, no rinse". Test organisms were Pseudomonas aeruginosa, Serratia marcescens, Staphylococcus aureus, Fusarium solani, Candida albicans and Acanthamoeba castellanii (trophozoites and cysts). Organisms, in the presence of organic soil, were inoculated on to Acuvue Oasys or Air Optix lenses and subjected to the solution manufacturer's recommended regimen. The number of surviving organisms on the lenses and in the soak solution was enumerated in accordance with ISO 14729. ISO 14729 dictates that for a given organism the combined average number of surviving microbes from the lenses and disinfectant soaking solution must be

Formation of liquid water at low temperatures via the deliquescence of calcium chloride: Implications for Antarctica and Mars

NASA Astrophysics Data System (ADS)

Gough, R. V.; Chevrier, V. F.; Tolbert, M. A.

2016-10-01

There is significant interest in the potential existence of even small amounts of liquid brine on current Mars. It has been proposed that aqueous solutions could form on Mars via the deliquescence of hygroscopic salts in contact with atmospheric water vapor, and these hygroscopic salts have recently been detected in recurring slope linae (RSL). While past work has largely focused on perchlorate species, another Mars-relevant salt that has a low eutectic temperature and may be deliquescent is calcium chloride, CaCl2. This salt may be linked to RSL formation on Mars, and deliquescence of CaCl2 is also known to be responsible for the only terrestrial RSL analog features known thus far: water tracks in the McMurdo Dry Valleys. Here we use Raman microscopy to monitor the low-temperature (223-273 K) deliquescence (solid to aqueous phase transition) and efflorescence (aqueous to solid phase transition) of two hydration states of CaCl2, the dihydrate and the hexahydrate. We find the deliquescence relative humidity (DRH) decreases with decreasing hydration state and with increasing temperature. Average DRH values over the temperature range studied are 15.8±3.5% RH for the dihydrate and 63.3±12.5% RH for the hexahydrate, making this salt at least as deliquescent as many perchlorate salts. A remarkable property of CaCl2 is its ability to persist as metastable, supersaturated brine. Once an aqueous solution was formed, efflorescence (recrystallization) of the liquid did not occur until single-digit RH values were reached (3.9±2.4% RH on average). We show that temperature and relative humidity conditions in the martian subsurface are sufficient to allow deliquescence of CaCl2, and the resulting brines may persist for over half of a martian sol. Therefore, this salt could play a role in RSL formation, the martian water cycle, and have implications for the potential habitability of Mars.

Accessible reactive surface area and abiotic redox reactivity of iron oxyhydroxides in acidic brines

NASA Astrophysics Data System (ADS)

Strehlau, Jennifer H.; Toner, Brandy M.; Arnold, William A.; Penn, R. Lee

2017-01-01

The reactivity of iron oxyhydroxide nanoparticles in low pH and high ionic strength solutions was quantified to assess abiotic contributions to oxidation-reduction chemistry in acidic brine environments, such as mine groundwater seepage, lakes in Western Australia, and acid mine drainage settings, which are of global interest for their environmental impacts and unique geomicrobiology. Factors expected to influence accessible and reactive surface area, including Fe(II) adsorption and aggregate size, were measured as a function of pH and CaCl2 concentration and related to the kinetics of redox reactions in aqueous suspensions of synthetic goethite (α-FeOOH), akaganeite (β-FeOOH), and ferrihydrite (Fe10O14(OH)2) nanoparticles. Aqueous conditions and iron oxyhydroxides were chosen based on characterization of natural iron-rich mine microbial mats located in Soudan Underground Mine State Park, Minnesota, USA. Quinone species were used as redox sensors because they are well-defined probes and are present in natural organic matter. Fe(II) adsorption to the iron oxyhydroxide mineral surfaces from aqueous solution was measurable only at pH values above 4 and either decreased or was not affected by CaCl2 concentration. Concentrations at or above 0.020 M CaCl2 in acetate buffer (pH 4.5) induced particle aggregation. Assessment of Fe(II) adsorption and particle aggregation in acidic brine suggested that accessible reactive surface area may be limited in acidic brines. This was supported by observations of decreasing benzoquinone reduction rate by adsorbed Fe(II) at high CaCl2 concentration. In contrast, the hydroquinone oxidation rate increased at high CaCl2 concentrations, which may be due to suppressed adsorption of Fe(II) generated by the reaction. Results suggest that iron geochemical cycling in acidic brine environments will be substantially different than for iron oxyhydroxides in low-saline waters with circumneutral pH. These findings have implications for acidic brine lakes and acid mine drainage locations that contain precipitated iron oxyhydroxides.

(Pyridoxylated hemoglobin)-(polyoxyethylene) conjugate solution as blood substitute for normothermic whole body rinse-out.

PubMed

Agishi, T; Funakoshi, Y; Honda, H; Yamagata, K; Kobayashi, M; Takahashi, M

1988-01-01

In order to investigate a new possibility for artificial blood with oxygen-carrying capability to be applied to other than mere supplementation, normothermic whole body rinse-out in which artificial blood deriving from perfluorochemical emulsion, Fluosol-DA 20% (Green Cross Co., Ltd., Osaka, Japan) or stabilized hemoglobin solution, (pyridoxylated hemoglobin)-(polyoxyethylene) conjugate solution (Ajinomoto Co., Ltd., Tokyo, Japan) were used as rinsing fluid for a blood purification experiment. Replacement either with approximately 150 ml/kg of Fluosol-DA or stabilized hemoglobin solution showed effective removal of digoxin at a reduction rate of 96.3% or 92.2%, respectively. However, when Fluosol-DA was used, a certain amount of perfluorochemical should be retrieved by centrifugation to avoid a possible toxic effect on the reticulo-endothelial system. Even though 3 out of 6, and 3 out of 8 dogs, respectively, survived for a long period after the procedure, the experimental dogs were very susceptible to infection.

Relationship between metal speciation in soil solution and metal adsorption at the root surface of ryegrass.

PubMed

Kalis, Erwin J J; Temminghoff, Erwin J M; Town, Raewyn M; Unsworth, Emily R; van Riemsdijk, Willem H

2008-01-01

The total metal content of the soil or total metal concentration in the soil solution is not always a good indicator for metal availability to plants. Therefore, several speciation techniques have been developed that measure a defined fraction of the total metal concentration in the soil solution. In this study the Donnan Membrane Technique (DMT) was used to measure free metal ion concentrations in CaCl(2) extractions (to mimic the soil solution, and to work under standardized conditions) of 10 different soils, whereas diffusive gradients in thin-films (DGT) and scanning chronopotentiometry (SCP) were used to measure the sum of free and labile metal concentrations in the CaCl(2) extracts. The DGT device was also exposed directly to the (wetted) soil (soil-DGT). The metal concentrations measured with the speciation techniques are related to the metal adsorption at the root surface of ryegrass (Lolium perenne L.), to be able to subsequently predict metal uptake. In most cases the metal adsorption related pH-dependently to the metal concentrations measured by DMT, SCP, and DGT in the CaCl(2) extract. However, the relationship between metal adsorption at the root surface and the metal concentrations measured by the soil-DGT was not-or only slightly-pH dependent. The correlations between metal adsorption at the root surface and metal speciation detected by different speciation techniques allow discussion about rate limiting steps in biouptake and the contribution of metal complexes to metal bioavailability.

METHOD OF IMPROVING CORROSION RESISTANCE OF ZIRCONIUM

DOEpatents

Shannon, D.W.

1961-03-28

An improved intermediate rinse for zirconium counteracts an anomalous deposit that often results in crevices and outof-the-way places when ordinary water is used to rinse away a strong fluoride etching solution designed to promote passivation of the metal. The intermediate rinse, which is used after the etching solution and before the water, is characterized by a complexing agent for fluoride ions such as aluminum or zirconium nitrates or chlorides.

The effect of calcium chloride on growth, photosynthesis, and antioxidant responses of Zoysia japonica under drought conditions.

PubMed

Xu, Chengbin; Li, Xuemei; Zhang, Lihong

2013-01-01

Few attempts have been made to study the alleviating effects of signal molecules on zoysiagrass (Zoysiajaponica) under drought stress. Calcium chloride has been shown to ameliorate the adverse effects of drought stress on many plants. It is necessary to investigate how to enhance drought tolerance of zoysiagrass using calcium chloride. The study elucidated the effects of calcium chloride on zoysiagrass under drought conditions by investigating the following parameters: biomass, chlorophyll (Chl) content, net photosynthetic rate (Pn), chlorophyll fluorescence, antioxidant enzymes, proline content, and malondialdehyde (MDA) content. Experimental conditions consisted of an aqueous CaCl2 solution at 5, 10, and 20 mM sprayed on zoysiagrass leaves for 3 d, following by an inducement of drought conditions by withholding water for 16 d. Under drought conditions, all CaCl2 pretreatments were found to increase the above-ground fresh biomass, as well as below-ground fresh and dry biomass. The resulting Chl (a, b, a+b) contents of the 5 and 10 mM CaCl2 pretreatment groups were higher than those of the control. In the later stages of drought conditions, the chlorophyll fluorescence parameter Fv/Fm was higher in leaves treated with 10 mM CaCl2 than in the leaves of the other two treatment groups. Zoysiagrass pretreated with 10 mM CaCl2 possessed both the maximum observed Pn and antioxidant enzyme activities. Meanwhile, lower MDA and proline contents were recorded in the plants pretreated with 5 and 10 mM CaCl2 under drought conditions. As a whole, the drought tolerance of zoysiagrass was improved to some extent by the application of a moderate calcium concentration.

The high-pressure phase transitions of hydroxides

NASA Astrophysics Data System (ADS)

Nishi, M.; Kuwayama, Y.; Tsuchiya, J.; Tsuchiya, T.; Irifune, T.

2017-12-01

The discovery of new high-pressure hydrous minerals has important implications for understanding the structure, dynamics, and evolution of the Earth, since hydrogen significantly affects the physical properties and stabilities of Earth's constituent minerals. Whereas hydrous minerals commonly dehydrate under pressures of around a few tens of gigapascals (GPa) and at temperature around 1,500 K, those with CaCl2-type crystal structure, MgSiO4H2 phase H, δ-AlOOH and ɛ-FeOOH, are known to be stable at pressures corresponding to the lower mantle. However, although the CaCl2-type hydroxides were suggested to form a solid solution owing to their similar crystal structure, there are few experimental studies on the stability of the hydroxide in such multicomponent. Moreover, ab initio calculations have predicted that some CaCl2-type hydroxides transform to pyrite-type structure at higher pressures. Here, we conducted high pressure-temperature experiments on pure AlOOH, FeOOH, and their solid solutions, with the aid of these first-principles predictions. We use in situ X-ray measurements in conjunction with a multi-anvil apparatus to study the high-pressure behaviour of hydroxides in the multicomponent system under middle lower mantle conditions. Solid solutions in wide compositional ranges between CaCl2-type δ-AlOOH and ɛ-FeOOH were recognized from X-ray diffraction patterns. Also, unit cell volume of FeOOH and (Al,Fe)OOH significantly decreased accompanied with the spin transition of iron at 50 GPa. Thus, the wide compositional ranges in CaCl2-type hydroxide are maintained beyond the depth of the middle lower mantle, where the spin transition of iron occurs. We used a laser-heated diamond anvil cell in order to study the stability of AlOOH and FeOOH at higher pressures above 70 GPa. We observed that ɛ-FeOOH transforms to the pyrite-type structure at above 80 GPa, which is consistent with the theoretical prediction. At conditions above 190 GPa and 2,500 K, we observed the phase transition of δ-AlOOH to its higher pressure phase at above 170 GPa although further experimental study should be required to determine the precise structure. Based on these experimental and theoretical results, the stability and phase transitions of hydrous phases in the lower mantle will be discussed.

Effect of Irrigation Time of Antiseptic Solutions on Bone Cell Viability and Growth Factor Release.

PubMed

Sawada, Kosaku; Nakahara, Ken; Haga-Tsujimura, Maiko; Fujioka-Kobayashi, Masako; Iizuka, Tateyuki; Miron, Richard J

2018-03-01

Antiseptic solutions are commonly utilized to treat local infection in the oral and maxillofacial region. However, surrounding vital bone is also exposed to antiseptic agents during irrigation and may have a potential negative impact on bone survival. The aim of the present study was therefore to investigate the effect of rinsing time with various antiseptic solutions on bone cell viability, as well as their subsequent release of growth factors important for bone regeneration. The bone samples collected from porcine mandible were rinsed in the following commonly utilized antiseptic solutions; povidone-iodine (0.5%), chlorhexidine digluconate (CHX, 0.2%), hydrogen peroxide (1%), and sodium hypochlorite (0.25%) for 1, 5, 10, 20, 30, or 60 minutes and assessed for cell viability and release of growth factors including vascular endothelial growth factor, transforming growth factor beta 1, bone morphogenetic protein 2, receptor activator of nuclear factor kappa-B ligand, and interleukin-1 beta by enzyme-linked immunosorbent assay. It was found in all the tested groups that the long exposure of any of the tested antiseptic solutions drastically promoted higher cell death. Sodium hypochlorite demonstrated the significantly highest cell death and at all time points. Interestingly, bone cell viability was highest in the CHX group post short-term rinsing of 1, 5, or 10 minutes when compared with the other 4 tested groups. A similar trend was also observed in subsequent growth factor release. The present study demonstrated that of the 4 tested antiseptic solutions, short-term CHX rinsing (ideally within 1 minute) favored bone cell viability and growth factor release. Clinical protocols should be adapted accordingly.

9 CFR 96.13 - Uncertified casings; disinfection with hydrochloric acid.

Code of Federal Regulations, 2014 CFR

2014-01-01

... solution, rinse them with water, and place them in a solution containing 81/2 pounds of sodium bicarbonate... from the sodium bicarbonate solution and wash them to remove the excess of bicarbonate. (Approved by...

9 CFR 96.13 - Uncertified casings; disinfection with hydrochloric acid.

Code of Federal Regulations, 2013 CFR

2013-01-01

... solution, rinse them with water, and place them in a solution containing 81/2 pounds of sodium bicarbonate... from the sodium bicarbonate solution and wash them to remove the excess of bicarbonate. (Approved by...

9 CFR 96.13 - Uncertified casings; disinfection with hydrochloric acid.

Code of Federal Regulations, 2012 CFR

2012-01-01

... solution, rinse them with water, and place them in a solution containing 81/2 pounds of sodium bicarbonate... from the sodium bicarbonate solution and wash them to remove the excess of bicarbonate. (Approved by...

9 CFR 96.13 - Uncertified casings; disinfection with hydrochloric acid.

Code of Federal Regulations, 2011 CFR

2011-01-01

... solution, rinse them with water, and place them in a solution containing 81/2 pounds of sodium bicarbonate... from the sodium bicarbonate solution and wash them to remove the excess of bicarbonate. (Approved by...

Liga developer apparatus system

DOEpatents

Boehme, Dale R.; Bankert, Michelle A.; Christenson, Todd R.

2003-01-01

A system to fabricate precise, high aspect ratio polymeric molds by photolithograpic process is described. The molds for producing micro-scale parts from engineering materials by the LIGA process. The invention is a developer system for developing a PMMA photoresist having exposed patterns comprising features having both very small sizes, and very high aspect ratios. The developer system of the present invention comprises a developer tank, an intermediate rinse tank and a final rinse tank, each tank having a source of high frequency sonic agitation, temperature control, and continuous filtration. It has been found that by moving a patterned wafer, through a specific sequence of developer/rinse solutions, where an intermediate rinse solution completes development of those portions of the exposed resist left undeveloped after the development solution, by agitating the solutions with a source of high frequency sonic vibration, and by adjusting and closely controlling the temperatures and continuously filtering and recirculating these solutions, it is possible to maintain the kinetic dissolution of the exposed PMMA polymer as the rate limiting step.

Growth Inhibitory Effects of Adhatoda vasica and Its Potential at Reducing Listeria monocytogenes in Chicken Meat

PubMed Central

Shukla, Shruti; Ahirwal, Laxmi; Bajpai, Vivek K.; Huh, Yun Suk; Han, Young-Kyu

2017-01-01

The inhibitory effects of Adhatoda vasica ethanolic leaf extract (AVELE) against Listeria monocytogenes were examined to assess its potential to preserve minimally processed meat products safely. The total phenolic, flavonoid, and alkaloid levels in AVELE were 10.09 ± 4.52 mg of gallic acid equivalents (GAE)/g, 22.43 ± 1.62 mg of quercetin equivalents/g, and 19.43 ± 3.90 mg/g, respectively. AVELE (1, 5, 10, or 20%) had considerable antibacterial effects against L. monocytogenes NCIM 24563 in terms of the inhibitory zones (7.4–13.6 mm), MIC (100 mg/mL or 10% formulated solution), reduced cell viability, potassium ion efflux, and the release of 260-nm absorbing materials and extracellular ATP. AVELE was used as a rinse solution (5, 10, and 20%) for raw chicken breast meat. A 20% rinsing solution applied for 60 min inhibited the L. monocytogenes NCIM 24563 counts significantly on raw chicken breast meat. Moreover, L. monocytogenes NCIM 24563 did not grow in the meat sample when the rinse time was increased to 90 min at the same concentration. L. monocytogenes showed a greater reduction to ~3 CFU/g after rinsing with a 10 and 20% AVELE solution for 30 min than with a 5% AVELE solution. The rinsing processes with AVELE produced the final cooked chicken products with higher sensory attribute scores, such as taste, juiciness, and tenderness, compared to the control group along with a decrease in microbial contamination. Chicken meat rinsed with AVELE (rinsing time of 90 min) showed better sensory attribute scores of juiciness and tenderness, as well as the overall sensory quality compared to the untreated group. This research highlights the effectiveness of AVELE against L. monocytogenes NCIM 24563, suggesting that AVELE can be used as an effective antimicrobial marinade and/or a rinse for meat preservation. PMID:28769879

Effects of humic acid and solution chemistry on the aggregation and dispersion of carboxyl-functionalized carbon black nanoparticles

NASA Astrophysics Data System (ADS)

Hwang, G.; Gomez-Flores, A.; Choi, S.; Han, Y., , Dr; Kim, H.

2017-12-01

The influence of humic acid, ionic strength and ionic species on the aggregation and dispersion of carboxyl-functionalized carbon black nanoparticles (CB-NPs) was systemically investigated in aqueous media. The experimental conditions of stability tests were selected to the changes in the solution chemistry (0.1-10 mM NaCl and 0.01-1 mM CaCl2) and in the presence/absence of humic acid (1 and 5 mg L-1) in an aquatic environment. The CB-NPs suspension was more rapidly settled in NaCl solution than in CaCl2. Specifically, in the case of NaCl, the aggregation rate of CB-NPs increased with ionic strength. Contrary, CB-NPs dispersed in CaCl2 were insensitive to the aggregation as the ionic strength increased; that was because specific adsorption of the divalent cation Ca2+ occurred since the zeta potential of the CB-NPs is reversed to a positive charge with increasing of the ionic strength. It was confirmed that humic acid greatly influences the stability of the CB-NPs. In particular, the dispersion of CB-NPs was improved in the whole range of ionic strengths of NaCl as well as of CaCl2. To support the results, the interaction energy between CB-NPs was calculated for each condition by using the classical Derjaguin-Landau-Verwey-Overbeek (DLVO) and modified-DLVO theories. In the presence of humic acid, the improved stability of CB-NPs is attributed to the steric repulsive force.This research was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2015R1D1A3A01020766), the Ministry of Education (MOE) and National Research Foundation of Korea (NRF) through the Human Resource Training Project for Regional Innovation (2015H1C1A1035930) and Korea Energy and Mineral Resources Engineering Program (KEMREP).

Physicochemical, sensory, and nutritional quality of fresh-cut "Rojo Brillante" persimmon affected by maturity stage and antibrowning agents.

PubMed

Sanchís, Elena; Mateos, Milagros; Pérez-Gago, María B

2016-10-01

To prevent enzymatic browning of fresh-cut 'Rojo Brillante' persimmon, different combinations of ascorbic acid (AA) and citric acid (CA) with calcium chloride (CaCl 2 ) were tested in fruit harvested at two maturity stages (MS1 and MS2). Color, firmness, sensory quality, total vitamin C, radical scavenging activity, total phenolic content, and carotenoids were evaluated over nine days of storage at 5 ℃. Antibrowning dips reduced enzymatic browning if compared with the control samples. Selecting fruits with good firmness and the addition of 10 g/l CaCl 2 help prevent loss of firmness of fresh-cut "Rojo Brillante" persimmons treated with acidic solutions as antibrowning agents to control enzymatic browning. The limit of marketability of the persimmon fruit processed at MS1 was significantly reduced by the burst of the disorder known as "flesh browning," and only the samples treated with 10 g/l CA + 10 g/l CaCl 2 maintained a limit of marketability close to seven days. At MS2, all the antibrowning solutions allowed a limit of marketability of seven storage days at 5 ℃. Nutritional quality was not affected by either antibrowning dips or cutting processes, but MS at harvest was. © The Author(s) 2016.

Use of Hydrogen Peroxide to Disinfect Hydroponic Plant Growth Systems

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Henderson, Keith

2000-01-01

Hydrogen peroxide was studied as an alternative to conventional bleach and rinsing methods to disinfect hydroponic plant growth systems. A concentration of 0.5% hydrogen peroxide was found to be effective. Residual hydrogen peroxide can be removed from the system by repeated rinsing or by flowing the solution through a platinum on aluminum catalyst. Microbial populations were reduced to near zero immediately after treatment but returned to pre-disinfection levels 2 days after treatment. Treating nutrient solution with hydrogen peroxide and planting directly into trays being watered with the nutrient solution without replenishment, was found to be detrimental to lettuce germination and growth.

Combined effect of zinc ions and cationic antibacterial agents on intraoral volatile sulphur compounds (VSC).

PubMed

Young, A; Jonski, G; Rölla, G

2003-08-01

Volatile sulphur compounds (VSC) are major components of oral malodour. As both zinc ions and cationic antibacterial agents inhibit the formation of oral VSC, this study aimed to determine whether these agents combined have synergistic anti-VSC actions. Baseline oral VSC measurements of mouth air from 10 volunteers following cysteine rinsing (6mM, pH 7.2) were obtained using gas chromatography (GC). Subjects rinsed for 1 min with 10ml of the test solutions, 0.3% zinc acetate (Zn), 0.025% chlorhexidine (CHX), 0.025% cetyl pyridinium (CPC), and the combinations Zn+CHX and Zn+CPC. Cysteine rinses were repeated at 1h, 2h and 3h and VSC measurements recorded. Three subjects rinsed with the Zn+CHX combination and fasted for 9h, undergoing cysteine rinses and VSC measurements at 3h intervals. 10 microl of the test solutions were also added to 1ml aliquots of human whole saliva (n=8). Following incubation at 37 degrees C for 24h VSC levels in the saliva headspace were measured by GC. Inhibition of VSC formation and the fractional inhibitory index indicating synergy were calculated. Zn+CHX mouthrinse had a synergistic anti-VSC effect, and was effective for at least 9h. Zn+CPC mouthrinse was less effective. Both combinations showed a synergistic inhibiting effect in-vitro. Synergy between Zn and the antibacterial agents confirms different mechanisms of operation.

[Effect of concomitant substances and addition order on the adsorption of Tween 80 on sand].

PubMed

Xu, Wei; Zhao, Yong-sheng; Li, Sui; Dai, Ning

2008-08-01

Adsorption of Tween 80 on sand was investigated, and the effect of inorganic salts (CaCl2), anionic surfactant (SDS) and lignosulphonates (sodium lignosulphonate or ammonium lignosulphonate) on the adsorption of Tween 80 on sand were evaluated at 25 degrees C. The results show that saturated adsorption amount of Tween 80 on sand enhance when CaCl2 or SDS is added into flushing solution of Tween 80. And the adsorption of Tween 80 on sand increase with the increase of molar fraction of CaCl2 or SDS in mixed flushing solution. And adsorption amount of Tween 80 on sand also enhance when SDS is added into sand firstly. The effects of mixing ratios and addition order of lignosulphonates on adsorption of Tween 80 were considered. The results show that with the increase of molar fraction of lignosulphonates in mixing flushing solution, adsorption amount of Tween 80 on sand decrease. The adsorption amount of Tween 80 reduce 20%-75% due to the exist of ammonium lignosulphonate is superior to sodium lignosulphonate (10%-60%) when mix the lignosulphonates-Tween 80 at the total mass ratios of 1:10, while the adsorption amount of Tween 80 reduce 70%-90% at the total mass ratios of 1:2. Lignosulphonates added into sand firstly is more efficient than that together. Therefore,use of lignosulphonates as a preflush can reduce the adsorption of surfactants on sand and is a better method to applied in in situ flushing.

Handwashing and Ebola virus disease outbreaks: A randomized comparison of soap, hand sanitizer, and 0.05% chlorine solutions on the inactivation and removal of model organisms Phi6 and E. coli from hands and persistence in rinse water

PubMed Central

Gallandat, Karin; Daniels, Kyle; Desmarais, Anne Marie; Scheinman, Pamela; Lantagne, Daniele

2017-01-01

To prevent Ebola transmission, frequent handwashing is recommended in Ebola Treatment Units and communities. However, little is known about which handwashing protocol is most efficacious. We evaluated six handwashing protocols (soap and water, alcohol-based hand sanitizer (ABHS), and 0.05% sodium dichloroisocyanurate, high-test hypochlorite, and stabilized and non-stabilized sodium hypochlorite solutions) for 1) efficacy of handwashing on the removal and inactivation of non-pathogenic model organisms and, 2) persistence of organisms in rinse water. Model organisms E. coli and bacteriophage Phi6 were used to evaluate handwashing with and without organic load added to simulate bodily fluids. Hands were inoculated with test organisms, washed, and rinsed using a glove juice method to retrieve remaining organisms. Impact was estimated by comparing the log reduction in organisms after handwashing to the log reduction without handwashing. Rinse water was collected to test for persistence of organisms. Handwashing resulted in a 1.94–3.01 log reduction in E. coli concentration without, and 2.18–3.34 with, soil load; and a 2.44–3.06 log reduction in Phi6 without, and 2.71–3.69 with, soil load. HTH performed most consistently well, with significantly greater log reductions than other handwashing protocols in three models. However, the magnitude of handwashing efficacy differences was small, suggesting protocols are similarly efficacious. Rinse water demonstrated a 0.28–4.77 log reduction in remaining E. coli without, and 0.21–4.49 with, soil load and a 1.26–2.02 log reduction in Phi6 without, and 1.30–2.20 with, soil load. Chlorine resulted in significantly less persistence of E. coli in both conditions and Phi6 without soil load in rinse water (p<0.001). Thus, chlorine-based methods may offer a benefit of reducing persistence in rinse water. We recommend responders use the most practical handwashing method to ensure hand hygiene in Ebola contexts, considering the potential benefit of chlorine-based methods in rinse water persistence. PMID:28231311

BPA qualtitative and quantitative assessment associated with orthodontic bonding in vivo.

PubMed

Kloukos, Dimitrios; Sifakakis, Iosif; Voutsa, Dimitra; Doulis, Ioannis; Eliades, George; Katsaros, Christos; Eliades, Theodore

2015-08-01

To assess the in vivo amount of BPA released from a visible light-cured orthodontic adhesive, immediately after bracket bonding. 20 orthodontic patients were recruited after obtaining informed consent. All patients received 24 orthodontic brackets in both dental arches. In Group A (11 patients), 25 ml of tap water were used for mouth rinsing, whereas in Group B (9 patients) a simulated mouth rinse formulation was used: a mixture of 20 ml de-ionized water plus 5 ml absolute ethanol. Rinsing solutions were collected before, immediately after placing the orthodontic appliances and after washing out the oral cavity and were then stored in glass tubes. Rinsing was performed in a single phase for 60s with the entire volume of each liquid. The BPA analysis was performed by gas chromatography-mass spectrometry. An increase in BPA concentration immediately after the 1st post-bonding rinse was observed, for both rinsing media, which was reduced after the 2nd post-bonding rinse. Water exhibited higher levels of BPA concentration than water/ethanol after 1st and 2nd post-bonding rinses. Two-way mixed Repeated Measures ANOVA showed that the primary null hypothesis declaring mean BPA concentration to be equal across rinsing medium and rinsing status was rejected (p-value <0.001). The main effects of the rinsing medium and status, as well as their interaction were found to be statistically significant (p-values 0.048, <0.001 and 0.011 respectively). A significant pattern of increase of BPA concentration, followed by a decrease that reached the initial values was observed. The amount of BPA was relatively low and far below the reference limits of tolerable daily intake. Copyright © 2015. Published by Elsevier Ltd.

Microstructural Characterization of Red Mud as Affected by Inorganic and Organic Chemicals Permeation

NASA Astrophysics Data System (ADS)

Rubinos, David A.; Valcárcel, Víctor; Spagnoli, Giovanni; Barral, María Teresa

2017-09-01

The microstructural characteristics of red mud (RM), especially specific surface area (SSA) and mesoporosity, and the effects of various representative fluids, namely methanol (80% v/v), trichloroethylene (TCE) (1100 mg/L), acetic acid (pH 2), and CaCl2 (5% w/v) aqueous solutions, were studied using N2-gas adsorption. The effect of compaction was also assessed. RM powder exhibited a moderate Brunauer-Emmet-Teller (BET)-SSA and is mostly a mesoporous (large mesopores, 200-500 Å) and a macroporous material. Compaction affected the macro and large, but not the fine, mesopores. Among the fluids, CaCl2 and acetic acid induced notable and opposing changes in RM microstructural characteristics. CaCl2 decreased SSA and suppressed fine mesoporosity, whereas acetic acid greatly enhanced them. Fractal analysis further indicated increasing surface roughness and heterogeneity of pore structure during acid exposure, altogether envisaging an improvement of adsorption capacity and a decrease of permeability of the RM.

Stress state during fixation determines susceptibility to fatigue-linked biodegradation in bioprosthetic heart valve materials.

PubMed

Margueratt, Sean D; Lee, J Michael

2002-01-01

Mechanical loading contributes to the structural deterioration of bioprosthetic heart valves. The influence of stress state during fixation may play a substantial role in their failure, linking fatigue damage caused by buckling and tension and the enzymatic degradation of glutaraldehyde-crosslinked collagen. Bovine pericardia were obtained immediately postmortem and 100 mm x 15 mm samples were cut in the base-to-apex direction. Half the samples were subjected to a uniaxial tensile stress of 250 kPa and half remained unloaded during a crosslinking treatment in 0.5% glutaraldehyde. Tissue samples were rinsed and cut into 16 mm x 4 mm test strips. Half of these strips were exposed to cyclic compressive buckling and alternating tension at 30 Hz for 20 million cycles (approx. 7.5 days) using a custom-built multi-sample fatigue system. Fatigue-damaged and non-damaged samples were subsequently incubated at 37 C for 48 hrs in: (i) Type I bacterial collagenase (20 U/ml) buffered in 0.05 M Tris, 10 mM CaCl2 2H2O (pH 7.4) or (ii) 0.05 M Tris buffer (pH 7.4) only. In both cases, the samples were loaded sinusoidally between 40 and 80 g using a previously described microtensile culture system. Tissue removed from the bath was rinsed in 0.1 M EDTA solution and mounted in a servo-hydraulic mechanical testing system (MTS). Ultimate tensile strength (UTS), maximum tissue modulus, and fracture strain were determined. The percent collagen solubilized was assessed by a colourmetric hydroxyproline assay of the enzyme bath and tissue sample. All data were analyzed by analysis of variance (ANOVA). The results confirmed the synergy between fatigue damage and collagenase proteolysis in these materials; however, there were no significant differences in this effect between simple fixation and stress-fixation up to 20 million cycles. There were significant decreases in the mechanical properties and an increase in the amount of collagen solubilized with increased exposure to fatigue cycling.

Mechanisms of superficial micropunctate corneal staining with sodium fluorescein: the contribution of pooling.

PubMed

Bandamwar, Kalika L; Garrett, Qian; Papas, Eric B

2012-04-01

To establish if sodium fluorescein (SFL) dye accumulation within intercellular spaces on the ocular surface contributes to the appearance of superficial punctate corneal staining. Thirteen subjects bilaterally wore PureVision™ lenses that had been pre-soaked in ReNu MultiPlus® multipurpose solution. After 1h of lens wear, corneal staining with SFL was assessed using a standard slit-lamp technique. Participants who presented with bilateral, corneal staining were selected for further evaluation. A randomly selected eye was rinsed with saline three times. Fellow eyes (control) received no rinsing. After each rinse, the appearance of SFL staining was recorded without any further instillation of the dye. To eliminate any confounding effects of staining due to residual fluorescein in the tear menisci, corneal staining was induced in freshly excised, isolated, rabbit eyes by topical administration of 0.001% PHMB and staining, rinsing and grading were performed as above. Nine out of 13 subjects presented with bilateral diffuse corneal staining (mean grade±SD: 2.4±0.7). The mean staining grades in test and control eyes respectively after each of the three rinses were (1) 2.41±0.41, 2.25±0.69 (p=0.9); (2) 2.34±0.79, 2.1±0.83 (p=0.8); and (3) 1.71±0.65, 1.60±0.79 (p=0.6) there was no significant reduction in staining with rinsing (p>0.05) and no difference was observed between test and control eyes at any sampling-point. Similar observations made in ex vivo rabbit eyes replicated these results. Pooling or accumulation of SFL solution within intercellular spaces does not appear to contribute to the appearance of superficial micropunctate corneal staining. Copyright © 2011 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Combined glucose ingestion and mouth rinsing improves sprint cycling performance.

PubMed

Chong, Edwin; Guelfi, Kym J; Fournier, Paul A

2014-12-01

This study investigated whether combined ingestion and mouth rinsing with a carbohydrate solution could improve maximal sprint cycling performance. Twelve competitive male cyclists ingested 100 ml of one of the following solutions 20 min before exercise in a randomized double-blinded counterbalanced order (a) 10% glucose solution, (b) 0.05% aspartame solution, (c) 9.0% maltodextrin solution, or (d) water as a control. Fifteen min after ingestion, repeated mouth rinsing was carried out with 11 × 15 ml bolus doses of the same solution at 30-s intervals. Each participant then performed a 45-s maximal sprint effort on a cycle ergometer. Peak power output was significantly higher in response to the glucose trial (1188 ± 166 W) compared with the water (1036 ± 177 W), aspartame (1088 ± 128 W) and maltodextrin (1024 ± 202 W) trials by 14.7 ± 10.6, 9.2 ± 4.6 and 16.0 ± 6.0% respectively (p < .05). Mean power output during the sprint was significantly higher in the glucose trial compared with maltodextrin (p < .05) and also tended to be higher than the water trial (p = .075). Glucose and maltodextrin resulted in a similar increase in blood glucose, and the responses of blood lactate and pH to sprinting did not differ significantly between treatments (p > .05). These findings suggest that combining the ingestion of glucose with glucose mouth rinsing improves maximal sprint performance. This ergogenic effect is unlikely to be related to changes in blood glucose, sweetness, or energy sensing mechanisms in the gastrointestinal tract.

Effects of ionic strength and temperature on the aggregation and deposition of multi-walled carbon nanotubes.

PubMed

Wang, Lixin; Yang, Xuezhi; Wang, Qi; Zeng, Yuxuan; Ding, Lei; Jiang, Wei

2017-01-01

The aggregation and deposition of carbon nanotubes (CNTs) determines their transport and fate in natural waters. Therefore, the aggregation kinetics of humic-acid treated multi-walled carbon nanotubes (HA-MWCNTs) was investigated by time-resolved dynamic light scattering in NaCl and CaCl 2 electrolyte solutions. Increased ionic strength induced HA-MWCNT aggregation due to the less negative zeta potential and the reduced electrostatic repulsion. The critical coagulation concentration (CCC) values of HA-MWCNTs were 80mmol/L in NaCl and 1.3mmol/L in CaCl 2 electrolyte, showing that Ca 2+ causes more serious aggregation than Na + . The aggregation behavior of HA-MWCNTs was consistent with Derjaguin-Landau-Verwey-Overbeek theory. The deposition kinetics of HA-MWCNTs was measured by the optical absorbance at 800nm. The critical deposition concentrations for HA-MWCNT in NaCl and CaCl 2 solutions were close to the CCC values, therefore the rate of deposition cannot be increased by changing the ionic strength in the diffusion-limited aggregation regime. The deposition process was correlated to the aggregation since larger aggregates increased gravitational deposition and decreased random Brownian diffusion. HA-MWCNTs hydrodynamic diameters were evaluated at 5, 15 and 25°C. Higher temperature caused faster aggregation due to the reduced electrostatic repulsion and increased random Brownian motion and collision frequency. HA-MWCNTs aggregate faster at higher temperature in either NaCl or CaCl 2 electrolyte due to the decreased electrostatic repulsion and increased random Brownian motion. Our results suggest that CNT aggregation and deposition are two correlated processes governed by the electrolyte, and CNT transport is favored at low ionic strength and low temperature. Copyright © 2016. Published by Elsevier B.V.

Dissolution of nontronite in chloride brines and implications for the aqueous history of Mars

NASA Astrophysics Data System (ADS)

Steiner, M. H.; Hausrath, E. M.; Elwood Madden, M. E.; Tschauner, O.; Ehlmann, B. L.; Olsen, A. A.; Gainey, S. R.; Smith, J. S.

2016-12-01

Increasing evidence suggests the presence of recent liquid water, including brines, on Mars. Brines have therefore likely impacted clay minerals such as the Fe-rich mineral nontronite found in martian ancient terrains. To interpret these interactions, we conducted batch experiments to measure the apparent dissolution rate constant of nontronite at 25.0 °C at activities of water (aH2O) of 1.00 (0.01 M CaCl2 or NaCl), 0.75 (saturated NaCl or 3.00 mol kg-1 CaCl2), and 0.50 (5.00 mol kg-1 CaCl2). Experiments at aH2O = 1.00 (0.01 M CaCl2) were also conducted at 4.0 °C, 25.0 °C, and 45.0 °C to measure an apparent activation energy for the dissolution of nontronite. Apparent dissolution rate constants at 25.0 °C in CaCl2-containing solutions decrease with decreasing activity of water as follows: 1.18 × 10-12 ± 9 × 10-14 mol mineral m-2 s-1 (aH2O = 1.00) > 2.36 × 10-13 ± 3.1 × 10-14 mol mineral m-2 s-1 (aH2O = 0.75) > 2.05 × 10-14 ± 2.9 × 10-15 mol mineral m-2 s-1 (aH2O = 0.50). Similar results were observed at 25.0 °C in NaCl-containing solutions: 1.89 × 10-12 ± 1 × 10-13 mol mineral m-2 s-1 (aH2O = 1.00) > 1.98 × 10-13 ± 2.3 × 10-14 mol mineral m-2 s-1 (aH2O = 0.75). This decrease in apparent dissolution rate constants with decreasing activity of water follows a relationship of the form: log kdiss = 3.70 ± 0.20 × aH2O - 15.49, where kdiss is the apparent dissolution rate constant, and aH2O is the activity of water. The slope of this relationship (3.70 ± 0.20) is within uncertainty of that of other minerals where the relationship between dissolution rates and activity of water has been tested, including forsteritic olivine (log R = 3.27 ± 0.91 × aH2O - 11.00) (Olsen et al., 2015) and jarosite (log R = 3.85 ± 0.43 × aH2O - 12.84) (Dixon et al., 2015), where R is the mineral dissolution rate. This result allows prediction of mineral dissolution as a function of activity of water and suggests that with decreasing activity of water, mineral dissolution will decrease due to the role of water as a ligand in the reaction. Apparent dissolution rate constants in the dilute NaCl solution (1.89 × 10-12 ± 1 × 10-13 mol mineral m-2 s-1) are slightly greater than those in the dilute CaCl2 solutions (1.18 × 10-12 ± 9 × 10-14 mol mineral m-2 s-1). We attribute this effect to the exchange of Na with Ca in the nontronite interlayer. An apparent activation energy of 54.6 ± 1.0 kJ/mol was calculated from apparent dissolution rate constants in dilute CaCl2-containing solutions at temperatures of 4.0 °C, 25.0 °C, and 45.0 °C: 2.33 × 10-13 ± 1.3 × 10-14 mol mineral m-2 s-1 (4.0 °C), 1.18 × 10-12 ± 9 × 10-14 mol mineral m-2 s-1 (25.0 °C), and 4.98 × 10-12 ± 3.8 × 10-13 mol mineral m-2 s-1 (45.0 °C). The greatly decreased dissolution of nontronite in brines and at low temperatures suggests that any martian nontronite found to be perceptibly weathered may have experienced very long periods of water-rock interaction with brines at the low temperatures prevalent on Mars, with important implications for the paleoclimate and long-term potential habitability of Mars.

Calcium interacts with antifreeze proteins and chitinase from cold-acclimated winter rye.

PubMed

Stressmann, Maja; Kitao, Satoshi; Griffith, Marilyn; Moresoli, Christine; Bravo, León A; Marangoni, Alejandro G

2004-05-01

During cold acclimation, winter rye (Secale cereale) plants accumulate pathogenesis-related proteins that are also antifreeze proteins (AFPs) because they adsorb onto ice and inhibit its growth. Although they promote winter survival in planta, these dual-function AFPs proteins lose activity when stored at subzero temperatures in vitro, so we examined their stability in solutions containing CaCl2, MgCl2, or NaCl. Antifreeze activity was unaffected by salts before freezing, but decreased after freezing and thawing in CaCl2 and was recovered by adding a chelator. Ca2+ enhanced chitinase activity 3- to 5-fold in unfrozen samples, although hydrolytic activity also decreased after freezing and thawing in CaCl2. Native PAGE, circular dichroism, and Trp fluorescence experiments showed that the AFPs partially unfold after freezing and thawing, but they fold more compactly or aggregate in CaCl2. Ruthenium red, which binds to Ca(2+)-binding sites, readily stained AFPs in the absence of Ca2+, but less stain was visible after freezing and thawing AFPs in CaCl2. We conclude that the structure of AFPs changes during freezing and thawing, creating new Ca(2+)-binding sites. Once Ca2+ binds to those sites, antifreeze activity, chitinase activity and ruthenium red binding are all inhibited. Because free Ca2+ concentrations are typically low in the apoplast, antifreeze activity is probably stable to freezing and thawing in planta. Ca2+ may regulate chitinase activity if concentrations are increased locally by release from pectin or interaction with Ca(2+)-binding proteins. Furthermore, antifreeze activity can be easily maintained in vitro by including a chelator during frozen storage.

In vitro mitochondrial test to assess haemodialyser biocompatibility.

PubMed

Tabouy, L J; Chauvet-Monges, A M; Brunet, P J; Braguer, D L; García, P A; Berland, Y F; Crevat, A D

1997-08-01

This paper describes an in vitro mitochondrial test to assess the biocompatibility of haemodialysers. We tested on isolated liver mitochondria the effect of solutions obtained by an aqueous rinse of different haemodialysers (cuprophane, cellulose acetate, Hemophan, polyacrylonitrile, polymethylmethacrylate, polysulphone, polyamide). Moreover, to determine the penetration into the cell and the cytotoxicity of these solutions from haemodialysers, we examined the effect of rinse solutions on HT29-D4 cells. Our results showed that rinse solutions from haemodialysers decrease the mitochondrial ATP synthesis. Cuprophane has the most marked effect, and the synthetic membranes exhibited only mild effects. Rinse solutions penetrated the cell and were cytotoxic by acting on mitochondria in the cell. In this respect, cellulosic membranes were the most toxic. Taken together our findings lead to a classification of haemodialyser membranes which is identical to one based on criteria such as activation of complement (cuprophane > other cellulosics > synthetics). Moreover isolated mitochondria make it possible to differentiate among the synthetic membranes. Isolated mitochondria thus appear to be a good in vitro test to assess the biocompatibility of haemodialysers.

Amp Synthesis in Aqueous Solution of Adenosine and Phosphorus Pentoxide

NASA Astrophysics Data System (ADS)

Yamagata, Y.; Kojima, H.; Ejiri, K.; Inomata, K.

1982-12-01

Possible formation of a P4O10 molecule in magma, the stability of the molecule in hydrous volcanic gas at high temperatures and a possible prebiotic phosphate cycle were discussed in relation to chemical evolution. To demonstrate the utility of phosphorus pentoxide as a phosphorylating agent, aqueous solutions of adenosine (0.02M) and phosphorus pentoxide (0.2M) were incubated at 37°C for 5 months. The pH of the solutions was adjusted every day or every few days to each fixed value (9.0, 10.5, 11.5, 12.5) with 10 N NaOH. The HPLC analysis showed the formation of 2'-AMP, 3'-AMP, 5'-AMP, cyclic (2' 3')-AMP and cyclic (3' 5')-AMP. The main components of the products were 2'- and 3'-AMP, though cyclic (2' 3')-AMP was the main component in the early period of the incubation at pH 9.0. The yields (conversion rate of adenosine to AMPs) were increased almost linearly with the incubation time for 5 months in the case of pH 9.0. The final yields were about 3% (pH 9.0), 6% (pH 9.0, 1 M NaCl), 5% (pH 9.0, 0.01 M CaCl2, 0.01 M MgCl2), 7% (pH 9.0, 0.5 M NaCl, 0.01 M CaCl2, 0.01 M MgCl2), 9% (pH 9.0, 1 M NaCl, 0.01 M CaCl2, 0.01 M MgCl2), 32% (pH 10.5), 43% (pH 11.5), 35% (pH 12.5).

Optimization of the model of abdominal aortic aneurysm by co-incubation of calcium chloride and collagenase in rats.

PubMed

Liu, Guang; Huang, Ying; Lu, Xin-Wu; Lu, Min; Huang, Xin-Tian; Li, Wei-Min; Jiang, Mi-Er

2009-08-01

To optimize the model of abdominal aortic aneurysm (AAA) in rats using calcium chloride (CaCl2) and collagenase together. This study was performed at the 9th People's Hospital, Institute of Traumatic Medicine, Shanghai Jiao Tong University, School of Medicine, Shanghai, China from July 2008 to February 2009. Aortas of 55 adult male Sprague-Dawley rats were exposed and incubated for 20 minutes with fresh normal saline solutions supplemented with CaCl2 (0.4 M) and collagenase (4%, w/v) (group A), CaCl2 alone (group B), collagenase alone (group C), or normal saline alone (group D). After 4 weeks, the treated aortas were evaluated by digital measurement, angiography, and histological examination. In group A, there was a mean increase in diameter of 87.86% +/- 69.49% (range, 35.33-299.29%) weeks after surgery. The frequency of AAA in this group was 83.3% (10/12). One (1/13) AAA occurred in group C and none in other groups. Partial endothelial loss, elastin disruption, and abnormal collagen deposition were noted in the AAA tissues in group A, corresponded well to native aneurysms in human. The use of collagenase optimized the established CaCl2-induced rat model, giving a high frequency of AAA in a short period of time.

The use of lithium as a marker for the retention of liquids in the oral cavity after rinsing.

PubMed

Hanning, Sara M; Kieser, Jules A; Ferguson, Martin M; Reid, Malcolm; Medlicott, Natalie J

2014-01-01

The aim of this study was to validate the use of lithium as a marker to indicate the retention of simple liquids in the oral cavity and use this to determine how much liquid is retained in the oral cavity following 30 s of rinsing. This is a validation study in which saliva was spiked with known concentrations of lithium. Twenty healthy participants then rinsed their mouths with either water or a 1 % w/v carboxymethylcellulose (CMC) solution for 30 s before expectorating into a collection cup. Total volume and concentration of lithium in the expectorant were then measured, and the percentage of liquid retained was calculated. The mean amount of liquid retained was 10.4 ± 4.7 % following rinsing with water and 15.3 ± 4.1 % following rinsing with 1 % w/v CMC solution. This difference was significant (p < 0.01). Lithium was useful as a marker for the retention of liquids in the oral cavity, and a value for the amount of water and 1 % w/v CMC solution remaining in the oral cavity following a 30-s rinse was established. The present study quantifies the retention of simple fluids in the oral cavity, validating a technique that may be applied to more complex fluids such as mouth rinses. Further, the application of this method to specific population groups such as those with severe xerostomia may assist in developing effective saliva substitutes.

NEUTRON RADIOGRAPHY MEASUREMENT OF SALT SOLUTION ABSORPTION IN MORTAR

PubMed Central

Lucero, Catherine L.; Spragg, Robert P.; Bentz, Dale P.; Hussey, Daniel S.; Jacobson, David L.; Weiss, W. Jason

2017-01-01

Some concrete pavements in the US have recently exhibited premature joint deterioration. It is hypothesized that one component of this damage can be attributed to a reaction that occurs when salt-laden water is absorbed in the concrete and reacts with the matrix. This study examines the absorption of CaCl2 solution in mortar via neutron imaging. Mortar specimens were prepared with water to cement ratios, (w/c), of 0.36, 0.42 and 0.50 by mass and exposed to chloride solutions with concentrations ranging from 0 % to 29.8 % by mass. Depth of fluid penetration and moisture content along the specimen length were determined for 96 h after exposure. At high salt concentration (29.8 %), the sorption rate decreased by over 80 % in all samples. Along with changes in surface tension and viscosity, CaCl2 reacts with the cement paste to produce products (Friedel’s salt, Kuzel’s salt, or calcium oxychloride) that block pores and reduce absorption. PMID:28626299

NEUTRON RADIOGRAPHY MEASUREMENT OF SALT SOLUTION ABSORPTION IN MORTAR.

PubMed

Lucero, Catherine L; Spragg, Robert P; Bentz, Dale P; Hussey, Daniel S; Jacobson, David L; Weiss, W Jason

2017-01-01

Some concrete pavements in the US have recently exhibited premature joint deterioration. It is hypothesized that one component of this damage can be attributed to a reaction that occurs when salt-laden water is absorbed in the concrete and reacts with the matrix. This study examines the absorption of CaCl 2 solution in mortar via neutron imaging. Mortar specimens were prepared with water to cement ratios, ( w/c ), of 0.36, 0.42 and 0.50 by mass and exposed to chloride solutions with concentrations ranging from 0 % to 29.8 % by mass. Depth of fluid penetration and moisture content along the specimen length were determined for 96 h after exposure. At high salt concentration (29.8 %), the sorption rate decreased by over 80 % in all samples. Along with changes in surface tension and viscosity, CaCl 2 reacts with the cement paste to produce products (Friedel's salt, Kuzel's salt, or calcium oxychloride) that block pores and reduce absorption.

40 CFR 420.96 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS IRON AND STEEL MANUFACTURING POINT SOURCE CATEGORY Acid Pickling...) Sulfuric acid pickling (spent acid solutions and rinse waters)—(1) Rod, wire, coil. Subpart I Pollutant or... operations. (b) Hydrochloric acid pickling (spent acid solutions and rinse waters)—(1) Rod, wire, coil...

40 CFR 420.95 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS IRON AND STEEL MANUFACTURING POINT SOURCE CATEGORY Acid Pickling... for existing sources. (a) Sulfuric acid (spent acid solutions and rinse waters)—(1) Rod, wire, and... pickling (spent acid solutions and rinse waters)—(1) Rod, wire, and coil. Subpart I Pollutant or pollutant...

Preparation of calcium- and magnesium-fortified potato starches with altered pasting properties.

PubMed

Noda, Takahiro; Takigawa, Shigenobu; Matsuura-Endo, Chie; Ishiguro, Koji; Nagasawa, Koichi; Jinno, Masahiro

2014-09-15

Calcium- and magnesium-fortified potato starches were prepared by immersion in various concentrations of CaCl2 and MgCl2 aqueous solutions, respectively. The pasting properties, i.e., peak viscosity and breakdown, of all the starches obtained above were analyzed using a Rapid Visco Analyzer. Furthermore, the gelatinization properties and in vitro digestibility of the representative calcium- and magnesium-fortified starches were tested. The maximum calcium content of the fortified potato starches was as high as 686 ppm with the addition of a high-concentration CaCl2 solution, while the calcium content of the control potato starch was 99 ppm. The magnesium content increased from 89 to 421 ppm by treatment of the potato starch with an MgCl2 solution. Markedly lower values of peak viscosity and breakdown were observed in calcium- and magnesium-fortified potato starches than in the control potato starch. However, the gelatinization temperature and enthalpy as well as resistant starch content of calcium- and magnesium-fortified potato starches were similar to those of the control potato starch. It is concluded that potato starches with altered pasting properties can be easily manufactured by the use of solutions containing high levels of calcium and magnesium.

Insight into the effect of organic and inorganic draw solutes on the flux stability and sludge characteristics in the osmotic membrane bioreactor.

PubMed

Siddique, Muhammad Saboor; Khan, Sher Jamal; Shahzad, Muhammad Aamir; Nawaz, Muhammad Saqib; Hankins, Nicholas P

2018-02-01

In this study, chloride based (CaCl 2 and MgCl 2 ) and acetate based (NaOAc and MgOAc) salts in comparison with NaCl were investigated as draw solutions (DS) to evaluate their viability in the osmotic membrane bioreactor (OMBR). Membrane distillation was coupled with an OMBR setup to develop a hybrid OMBR-MD system, for the production of clean water and DS recovery. Results demonstrate that organic DS were able to mitigate the salinity buildup in the bioreactor as compared to inorganic salts. Prolonged filtration runs were observed with MgCl 2 and MgOAc in contrast with other draw solutes at the same molar concentration. Significant membrane fouling was observed with NaOAc while rapid flux decline due to increased salinity build-up was witnessed with NaCl and CaCl 2 . Improved characteristics of mixed liquor in terms of sludge filterability, particle size, and biomass growth along with the degradation of soluble microbial products (SMP) were found with organic DS. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dehydration of an ethanol/water azeotrope through alginate-DNA membranes cross-linked with metal ions by pervaporation.

PubMed

Uragami, Tadashi; Banno, Masashi; Miyata, Takashi

2015-12-10

To obtain high dehydration membranes for an ethanol/water azeotrope, dried blend membranes prepared from mixtures of sodium alginate (Alg-Na) and sodium deoxyribonucleate (DNA-Na) were cross-linked by immersing in a methanol solution of CaCl2 or MaCl2. In the dehydration of an ethanol/water azeotropic mixture by pervaporation, the effects of immersion time in methanol solution of CaCl2 or MaCl2 on the permeation rate and water/ethanol selectivity through Alg-DNA/Ca(2+) and Alg-DNA/Mg(2+) cross-linked membranes were investigated. Alg-DNA/Mg(2+) cross-linked membrane immersed for 12h in methanol solution of MaCl2 exhibited the highest water/ethanol selectivity. This results from depressed swelling of the membranes by formation of a cross-linked structure. However, excess immersion in solution containing cross-linker led to an increase in the hydrophobicity of cross-linked membrane. Therefore, the water/ethanol selectivity of Alg-DNA/Mg(2+) cross-linked membranes with an excess immersion in cross-linking solution was lowered. The relationship between the structure of Alg-DNA/Ca(2+) and Alg-DNA/Mg(2+) cross-linked membranes and their permeation and separation characteristics during pervaporation of an ethanol/water azeotropic mixture is discussed in detail. Copyright © 2015 Elsevier Ltd. All rights reserved.

Calcium Prerinse before Fluoride Rinse Reduces Enamel Demineralization: An in situ Caries Study.

PubMed

Souza, João Gabriel S; Tenuta, Livia Maria Andaló; Del Bel Cury, Altair Antoninha; Nóbrega, Diego Figueiredo; Budin, Renan R; de Queiroz, Mateus X; Vogel, Gerald L; Cury, Jaime A

2016-01-01

A calcium (Ca) prerinse before a fluoride (F) rinse has been shown to increase oral F levels. We tested the anticaries effect of this combination in a dose-response in situ caries model. In a double-blind, crossover experiment, 10 volunteers carried enamel slabs in palatal appliances for 14 days, during which they rinsed twice/day with one of four rinse combinations: (1) a placebo prerinse (150 mM sodium lactate) followed by a distilled water rinse (negative control); (2) a placebo prerinse followed by a 250 ppm F rinse; (3) a placebo prerinse followed by a 1,000 ppm F rinse, or (4) a Ca prerinse (150 mM Ca, as calcium lactate) followed by a 250 ppm F rinse. Sucrose solution was dripped onto the slabs 8×/day to simulate a high cariogenic challenge. The percent surface hardness loss (%SHL) was significantly lower in the Ca prerinse used with the 250 ppm F rinse group (%SHL = 38.0 ± 21.0) when compared with the F rinse alone (%SHL = 59.5 ± 24.1) and similar to the 1,000 ppm F rinse group (%SHL = 42.0 ± 18.3). Compared with the 250 ppm F rinse, the Ca prerinse increased biofilm fluid F only twice (nonsignificant). However, it greatly increased F in biofilm solids (∼22×). The Ca prerinse had little effect on loosely or firmly bound enamel F. The results showed an increased level of protection against demineralization by the use of a Ca prerinse, which seems to be caused by the enhancement of F concentration in the biofilm. © 2016 S. Karger AG, Basel.

Two-dimensional self-assembly of DNA-functionalized gold nanoparticles

NASA Astrophysics Data System (ADS)

Wang, Wenjie; Zhang, Honghu; Hagen, Noah; Kuzmenko, Ivan; Akinc, Mufit; Travesset, Alex; Mallapragada, Surya; Vaknin, David

2D superlattices of nanoparticles (NPs) are promising candidates for nano-devices. It is still challenging to develop a simple yet efficient protocol to assemble NPs in a controlled manner. Here, we report on formation of 2D Gibbs monolayers of single-stranded DNA-coated gold nanoparticles (ssDNA-AuNPs) at the air-water interface by manipulation of salts contents. MgCl2 and CaCl2 in solutions facilitate the accumulation of the non-complementary ssDNA-AuNPs on aqueous surfaces. Grazing-incidence small-angle X-ray scattering (GISAXS) and X-ray reflectivity show that the surface AuNPs assembly forms a mono-particle layer and undergoes a transformation from short-range to long-range (hexagonal) order above a threshold of [MgCl2] or [CaCl2]. For solutions that include two kinds of ssDNA-AuNPs with complementary base-pairing, the surface AuNPs form a thicker film and only in-plane short-range order is observed. By using other salts (NaCl or LaCl3) at concentrations of similar ionic strength to those of MgCl2 or CaCl2, we find that surface adsorbed NPs lack any orders. X-ray fluorescence measurements provide direct evidence of surface enrichment of AuNPs and divalent ions (Ca2 +) . The work was supported by the Office of Basic Energy Sciences, USDOE under Contract No. DE-AC02-07CH11358 and DE-AC02-06CH11357.

MICRURGICAL STUDIES IN CELL PHYSIOLOGY

PubMed Central

Chambers, Robert; Reznikoff, Paul

1926-01-01

By means of micro-dissection and injection Amœba proteus was treated with the chlorides of Na, K, Ca, and Mg alone, in combination, and with variations of pH. I. The Plasmalemma. 1. NaCl weakens and disrupts the surface membrane of the ameba. Tearing the membrane accelerates the disruption which spreads rapidly from the site of the tear. KCl has no disruptive effect on the membrane but renders it adhesive. 2. MgCl2 and CaCl2 have no appreciable effect on the integrity of the surface membrane of the ameba when applied on the outside. No spread of disruption occurs when the membrane is torn in these salts. When these salts are introduced into the ameba they render the pellicle of the involved region rigid. II. The Internal Protoplasm. 3. Injected water either diffuses through the protoplasm or becomes localized in a hyaline blister. Large amounts when rapidly injected produce a "rushing effect". 4. HCl at pH 1.8 solidifies the internal protoplasm and at pH 2.2 causes solidification only after several successive injections. The effect of the subsequent injections may be due to the neutralization of the cell-buffers by the first injection. 5. NaCl and KCl increase the fluidity of the internal protoplasm and induce quiescence. 6. CaCl2 and MgCl2 to a lesser extent solidify the internal protoplasm. With CaCl2 the solidification tends to be localized. With MgCl2 it tends to spread. The injection of CaCl2 accelerates movement in the regions not solidified whereas the injection of MgCl2 induces quiescence. III. Pinching-Off Reaction. 7. A hyaline blister produced by the injection of water may be pinched off. The pinched-off blister is a liquid sphere surrounded by a pellicle. 8. Pinching off always takes place with injections of HCl when the injected region is solidified. 9. The injection of CaCl2 usually results in the pinching off of the portion solidified. The rate of pinching off varies with the concentration of the salt. The injection of MgCl2 does not cause pinching off. IV. Reparability of Torn Surfaces. 10. The repair of a torn surface takes place readily in distilled water. In the different salt solutions, reparability varies specifically with each salt, with the concentration of the salt, and with the extent of the tear. In NaCl and in KCl repair occurs less readily than in water. In MgCl2 repair takes place with great difficulty. In CaCl2 a proper estimate of the process of repair is complicated by the pinching-off phenomenon. However, CaCl2 is the only salt found to increase the mobility of the plasmalemma, and this presumably enhances its reparability. 11. The repair of the surface is probably a function of the internal protoplasm and depends upon an interaction of the protoplasm with the surrounding medium. V. Permeability. 12. NaCl and KCl readily penetrate the ameba from the exterior. CaCl2 and MgCl2 do not. 13. All four salts when injected into an ameba readily diffuse through the internal protoplasm. In the case of CaCl2 the diffusion may be arrested by the pinching-off process. VI. Toxicity. 14. NaCl and KCl are more toxic to the exterior of the cell than to the interior, and the reverse is true for CaCl2 and MgCl2. 15. The relative non-toxicity of injected NaCl to the interior of the ameba is not necessarily due to its diffusion outward from the cell. 16. HCl is much more toxic to the exterior of a cell than to the interior; at pH 5.5 it is toxic to the surface whereas at pH 2.5 it is not toxic to the interior. NaOH to pH 9.8 is not toxic either to the surface or to the interior. VII. Antagonism. 17. The toxic effects of NaCl and of KCl on the exterior of the cell can be antagonized by CaCl2 and this antagonism occurs at the surface. Although the lethal effect of NaCl is thus antagonized, NaCl still penetrates but at a slower rate than if the ameba were immersed in a solution of this salt alone. 18. NaCl and HCl are mutually antagonistic in the interior of the ameba. No antagonism between the salts and HCl was found on the exterior of the ameba. No antagonism between the salts and NaOH was found on the interior or exterior of the ameba. 19. The pinching-off phenomenon can be antagonized by NaCl or by KCl, and the rate of the retardation of the pinching-off process varies with the concentration of the antagonizing salt. 20. The prevention of repair of a torn membrane by toxic solutions of NaCl or KCl can be antagonized by CaCl2. These experiments show directly the marked difference between the interior and the exterior of the cell in their behavior toward the chlorides of Na, K, Ca, and Mg. PMID:19872206

Effects of caffeine and carbohydrate mouth rinses on repeated sprint performance.

PubMed

Beaven, C Martyn; Maulder, Peter; Pooley, Adrian; Kilduff, Liam; Cook, Christian

2013-06-01

Our purpose was to examine the effectiveness of carbohydrate and caffeine mouth rinses in enhancing repeated sprint ability. Previously, studies have shown that a carbohydrate mouth rinse (without ingestion) has beneficial effects on endurance performance that are related to changes in brain activity. Caffeine ingestion has also demonstrated positive effects on sprint performance. However, the effects of carbohydrate or caffeine mouth rinses on intermittent sprints have not been examined previously. Twelve males performed 5 × 6-s sprints interspersed with 24 s of active recovery on a cycle ergometer. Twenty-five milliliters of either a noncaloric placebo, a 6% glucose, or a 1.2% caffeine solution was rinsed in the mouth for 5 s prior to each sprint in a double-blinded and balanced cross-over design. Postexercise maximal heart rate and perceived exertion were recorded, along with power measures. A second experiment compared a combined caffeine-carbohydrate rinse with carbohydrate only. Compared with the placebo mouth rinse, carbohydrate substantially increased peak power in sprint 1 (22.1 ± 19.5 W; Cohen's effect size (ES), 0.81), and both caffeine (26.9 ± 26.9 W; ES, 0.71) and carbohydrate (39.1 ± 25.8 W; ES, 1.08) improved mean power in sprint 1. Experiment 2 demonstrated that a combination of caffeine and carbohydrate improved sprint 1 power production compared with carbohydrate alone (36.0 ± 37.3 W; ES, 0.81). We conclude that carbohydrate and (or) caffeine mouth rinses may rapidly enhance power production, which could have benefits for specific short sprint exercise performance. The ability of a mouth-rinse intervention to rapidly improve maximal exercise performance in the absence of fatigue suggests a central mechanism.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Kimberly; Bennett, Philip C.; Wolfe, Will

Dissolution of CO2 into deep subsurface brines for carbon sequestration is regarded as one of the few viable means of reducing the amount of CO2 entering the atmosphere. Ions in solution partially control the amount of CO2 that dissolves, but the mechanisms of the ion's influence are not clearly understood and thus CO2 solubility is difficult to predict. In this study, CO2 solubility was experimentally determined in water, NaCl, CaCl2, Na2SO4, and NaHCO3 solutions and a mixed brine similar to the Bravo Dome natural CO2 reservoir; ionic strengths ranged up to 3.4 molal, temperatures to 140 °C, and CO2 pressuresmore » to 35.5 MPa. Increasing ionic strength decreased CO2 solubility for all solutions when the salt type remained unchanged, but ionic strength was a poor predictor of CO2 solubility in solutions with different salts. A new equation was developed to use ion hydration number to calculate the concentration of electrostricted water molecules in solution. Dissolved CO2 was strongly correlated (R2 = 0.96) to electrostricted water concentration. Strong correlations were also identified between CO2 solubility and hydration enthalpy and hydration entropy. These linear correlation equations predicted CO2 solubility within 1% of the Bravo Dome brine and within 10% of two mixed brines from literature (a 10 wt % NaCl + KCl + CaCl2 brine and a natural Na+, Ca2+, Cl- type brine with minor amounts of Mg2+, K+, Sr2+ and Br-).« less

Short-term effect of strontium- and zinc-containing toothpastes and mouthrinses on volatile sulphur compounds in morning breath: a randomized, double-blind, cross-over clinical study.

PubMed

Soares, Léo G; Jonski, Grazyna; Tinoco, Eduardo M B; Young, Alix

2015-04-01

Zinc (Zn) reduces the formation of volatile sulphur compounds (VSCs) associated with oral malodour. Although strontium (Sr) is included in some products for reducing dental hypersensitivity, it may also have anti-halitosis properties. This randomized, double-blind, cross-over clinical study compared the anti-VSC effect of brushing with commercial toothpastes and rinses containing Zn and Sr. The volunteers (n = 30) either brushed/rinsed with/without tongue brushing using Zn-containing toothpaste/rinse, Sr-containing toothpaste/rinse, or placebo (control). Volatile sulphur compounds [hydrogen sulphide (H2 S) and methyl mercaptan (CH3 SH)] were measured, in morning breath, using gas chromatography. The anti-VSC effects of the test toothpastes and test rinses were significantly better than the anti-VSC effects of the respective controls. Toothbrushing with test toothpastes gave median reductions, compared with the control, of 70% for H2 S and 55-57% for CH3 SH. Rinsing with the Sr- and Zn-containing solutions had the same anti-VSC effect as toothbrushing and tooth- and tongue brushing with the Sr- and Zn-containing toothpastes. Zinc-containing rinse resulted in a significantly higher median salivary level of Zn compared with brushing with Zn-containing toothpaste, although this effect did not correlate with the anti-VSC effect. It can be concluded that the Sr- and Zn-containing toothpastes and the Zn- and Sr-containing rinses, when used in the evening, are equally effective in reducing morning-breath VSCs the following day. © 2015 Eur J Oral Sci.

Optimized water vapor permeability of sodium alginate films using response surface methodology

NASA Astrophysics Data System (ADS)

Zhang, Qing; Xu, Jiachao; Gao, Xin; Fu, Xiaoting

2013-11-01

The water vapor permeability (WVP) of films is important when developing pharmaceutical applications. Films are frequently used as coatings, and as such directly influence the quality of the medicine. The optimization of processing conditions for sodium alginate films was investigated using response surface methodology. Single-factor tests and Box-Behnken experimental design were employed. WVP was selected as the response variable, and the operating parameters for the single-factor tests were sodium alginate concentration, carboxymethyl cellulose (CMC) concentration and CaCl2 solution immersion time. The coefficient of determination ( R 2) was 0.97, indicating statistical significance. A minimal WVP of 0.389 8 g·mm/(m2·h·kPa) was achieved under the optimum conditions. These were found to be a sodium alginate concentration, CMC concentration and CaCl2 solution immersion time at 8.04%, 0.13%, and 12 min, respectively. This provides a reference for potential applications in manufacturing film-coated hard capsule shells.

Effects of surfactant and salt species in reverse micellar forward extraction efficiency of isoflavones with enriched protein from soy flour.

PubMed

Zhao, Xiaoyan; Wei, Zhiyi; Du, Fangling; Zhu, Junqing

2010-11-01

Suitability of reverse micelles of anionic surfactant sodium bis(2-ethyl hexyl) sulfosuccinate (AOT) and sodium dodecyl sulfate (SDS), cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB) and nonionic surfactant polyoxyethylene p-t-octylphenol (TritonX-100) in organic solvent isooctane for extraction of soy isoflavone-enriching proteins was investigated. The results showed that the order of combined isoflavone contents was SDS>CTAB>Triton X-100>AOT, while the order of protein recovery was SDS>AOT>TritonX-100>CTAB. As compared with ACN-HCl extraction, the total amount of isoflavones was lower than reverse micellar extraction. Ion strength was one of the important conditions to control extraction of isoflavone-enriching proteins with AOT reversed micelles. For the six salt systems, KNO(3), KCl, MgCl(2), CaCl(2), NaCl, and Na(2)SO(4), extracted fraction of isoflavone-enriching proteins was measured. Salt solutions greatly influenced the extraction efficiency of isoflavones in an order of KNO(3)>MgCl(2)>CaCl(2)>KCl>NaCl>Na(2)SO(4), while protein in an order of MgCl(2)>CaCl(2)>NaCl>KNO(3)>Na(2)SO(4)>KCl.

In Situ Antibacterial Activity of Essential Oils with and without Alcohol on Oral Biofilm: A Randomized Clinical Trial

PubMed Central

Quintas, Victor; Prada-López, Isabel; Carreira, María J.; Suárez-Quintanilla, David; Balsa-Castro, Carlos; Tomás, Inmaculada

2017-01-01

Currently, there is little evidence on the in situ antibacterial activity of essential oils (EO) without alcohol. This study aimed to evaluate in situ the substantivity and antiplaque effect on the plaque-like biofilm (PL-biofilm) of two solutions, a traditional formulation that contains EO with alcohol (T-EO) and an alcohol-free formulation of EO (Af-EO). Eighteen healthy adults performed a single mouthwash of: T-EO, Af-EO, and sterile water (WATER) after wearing an individualized disk-holding splint for 2 days. The bacterial viability (BV) and thickness of the PL-biofilm were quantified at baseline, 30 s, and 1, 3, 5, and 7 h post-rinsing (Test 1). Subsequently, each volunteer wore the splint for 4 days, applying two daily mouthwashes of: T-EO, Af-EO, and WATER. The BV, thickness, and covering grade (CG) of the PL-biofilm were quantified (Test 2). Samples were analyzed by confocal laser scanning microscopy after staining with the LIVE/DEAD® BacLight™ solution. To conduct the computations of the BV automatically, a Matlab toolbox called Dentius Biofilm was developed. In test 1, both EO antiseptics had a similar antibacterial effect, reducing BV after a single rinse compared to the WATER, and keeping it below baseline levels up to 7 h post-rinse (P < 0.001). The mean thickness of the PL-biofilm after rinsing was not affected by any of the EO formulations and ranged from 18.58 to 20.19 μm. After 4 days, the T-EO and Af-EO solutions were significantly more effective than the WATER, reducing the BV, thickness, and CG of the PL-biofilm (P < 0.001). Although, both EO antiseptics presented a similar bactericidal activity, the Af-EO rinses led to more significant reductions in the thickness and CG of the PL-biofilm than the T-EO rinses (thickness = 7.90 vs. 9.92 μm, P = 0.012; CG = 33.36 vs. 46.61%, P = 0.001). In conclusion, both essential oils antiseptics had very high immediate antibacterial activity and substantivity in situ on the 2-day PL-biofilm after a single mouthwash. In the 4-day PL-biofilm, both essential oils formulations demonstrated a very good antiplaque effect in situ, although the alcohol-free formula performed better at reducing the biofilm thickness and covering grade. PMID:29218030

21 CFR 355.50 - Labeling of anticaries drug products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... polish,” “tooth powder;” (optional: “dental”) “preventive treatment gel;” or (optional: “treatment” or “dental”)) (select one of the following: “rinse,” “concentrated solution,” “rinse powder,” or “rinse..., under the heading “Indication,” the following: “Aids in the prevention of dental (select one of the...

Probing the Surface Charge on the Basal Planes of Kaolinite Particles with High-Resolution Atomic Force Microscopy

PubMed Central

2017-01-01

High-resolution atomic force microscopy is used to map the surface charge on the basal planes of kaolinite nanoparticles in an ambient solution of variable pH and NaCl or CaCl2 concentration. Using DLVO theory with charge regulation, we determine from the measured force–distance curves the surface charge distribution on both the silica-like and the gibbsite-like basal plane of the kaolinite particles. We observe that both basal planes do carry charge that varies with pH and salt concentration. The silica facet was found to be negatively charged at pH 4 and above, whereas the gibbsite facet is positively charged at pH below 7 and negatively charged at pH above 7. Investigations in CaCl2 at pH 6 show that the surface charge on the gibbsite facet increases for concentration up to 10 mM CaCl2 and starts to decrease upon further increasing the salt concentration to 50 mM. The increase of surface charge at low concentration is explained by Ca2+ ion adsorption, while Cl– adsorption at higher CaCl2 concentrations partially neutralizes the surface charge. Atomic resolution imaging and density functional theory calculations corroborate these observations. They show that hydrated Ca2+ ions can spontaneously adsorb on the gibbsite facet of the kaolinite particle and form ordered surface structures, while at higher concentrations Cl– ions will co-adsorb, thereby changing the observed ordered surface structure. PMID:29140711

Probing the Surface Charge on the Basal Planes of Kaolinite Particles with High-Resolution Atomic Force Microscopy.

PubMed

Kumar, N; Andersson, M P; van den Ende, D; Mugele, F; Siretanu, I

2017-12-19

High-resolution atomic force microscopy is used to map the surface charge on the basal planes of kaolinite nanoparticles in an ambient solution of variable pH and NaCl or CaCl 2 concentration. Using DLVO theory with charge regulation, we determine from the measured force-distance curves the surface charge distribution on both the silica-like and the gibbsite-like basal plane of the kaolinite particles. We observe that both basal planes do carry charge that varies with pH and salt concentration. The silica facet was found to be negatively charged at pH 4 and above, whereas the gibbsite facet is positively charged at pH below 7 and negatively charged at pH above 7. Investigations in CaCl 2 at pH 6 show that the surface charge on the gibbsite facet increases for concentration up to 10 mM CaCl 2 and starts to decrease upon further increasing the salt concentration to 50 mM. The increase of surface charge at low concentration is explained by Ca 2+ ion adsorption, while Cl - adsorption at higher CaCl 2 concentrations partially neutralizes the surface charge. Atomic resolution imaging and density functional theory calculations corroborate these observations. They show that hydrated Ca 2+ ions can spontaneously adsorb on the gibbsite facet of the kaolinite particle and form ordered surface structures, while at higher concentrations Cl - ions will co-adsorb, thereby changing the observed ordered surface structure.

Damage development, phase changes, transport properties, and freeze-thaw performance of cementitious materials exposed to chloride based salts

NASA Astrophysics Data System (ADS)

Farnam, Yaghoob

Recently, there has been a dramatic increase in premature deterioration in concrete pavements and flat works that are exposed to chloride based salts. Chloride based salts can cause damage and deterioration in concrete due to the combination of factors which include: increased saturation, ice formation, salt crystallization, osmotic pressure, corrosion in steel reinforcement, and/or deleterious chemical reactions. This thesis discusses how chloride based salts interact with cementitious materials to (1) develop damage in concrete, (2) create new chemical phases in concrete, (3) alter transport properties of concrete, and (4) change the concrete freeze-thaw performance. A longitudinal guarded comparative calorimeter (LGCC) was developed to simultaneously measure heat flow, damage development, and phase changes in mortar samples exposed to sodium chloride (NaCl), calcium chloride (CaCl 2), and magnesium chloride (MgCl2) under thermal cycling. Acoustic emission and electrical resistivity measurements were used in conjunction with the LGCC to assess damage development and electrical response of mortar samples during cooling and heating. A low-temperature differential scanning calorimetry (LT-DSC) was used to evaluate the chemical interaction that occurs between the constituents of cementitious materials (i.e., pore solution, calcium hydroxide, and hydrated cement paste) and salts. Salts were observed to alter the classical phase diagram for a salt-water system which has been conventionally used to interpret the freeze-thaw behavior in concrete. An additional chemical phase change was observed for a concrete-salt-water system resulting in severe damage in cementitious materials. In a cementitious system exposed to NaCl, the chemical phase change occurs at a temperature range between -6 °C and 8 °C due to the presence of calcium sulfoaluminate phases in concrete. As a result, concrete exposed to NaCl can experience additional freeze-thaw cycles due to the chemical phase change creating cracks and damage to concrete under freezing and thawing. In a cementitious system exposed to CaCl2, the chemical phase change is mainly due to the presence of calcium hydroxide (CH) in concrete. Calcium hydroxide can react with CaCl2 solution producing calcium oxychloride. Calcium oxychloride forms at room temperature (i.e., 23 °C) for CaCl 2 salt concentrations at or above ~ 12 % by mass in the solution creating expansion and degradation in concrete. In a cementitious system exposed to MgCl2, it was observed that MgCl2 can be entirely consumed in concrete by reacting with CH and produce CaCl2. As such, it followed a response that is more similar to the concrete-CaCl2-water system than that of the MgCl2-water phase diagram. Formation of calcium/magnesium oxychloride is most likely the main source of the chemical phase change (which can cause damage) in concrete exposed to MgCl2. During the LGCC testing for CaCl2 and MgCl2 salts, it was found that the chemical reactions occur rapidly (~ 10 min) and can cause a significant decrease in subsequent fluid ingress into exposed concrete in comparison to NaCl. Isothermal calorimetry, fluid absorption, oxygen permeability, oxygen diffusivity, and X-ray fluorescence testing showed that the formation of calcium oxychloride in concrete exposed to CaCl2 and MgCl 2 can block or fill in the concrete pores on the surface of the specimen; thereby decreasing the CaCl2 and MgCl2 fluid ingress into the concrete. To mitigate the damage and degradation due to the chemical phase transition, two approaches were evaluated: (1) use of a cementitious binder that does not react with salts, and (2) use of a new practical technology to melt ice and snow, thereby decreasing the demand for deicing salt usage. For the first approach, carbonated calcium silicate based cement (CCSC) was used and the CCSC mortar showed a promising performance and resistance to salt degradation than an ordinary portland mortar does. For the second approach, phase change materials (PCM), including paraffin oil and methyl laurate, were used to store heat in concrete elements and release the stored heat during cooling to reduce ice formation and snow accumulation on the surface of concrete. PCM approach also showed a promising performance in melting ice and snow, thereby decreasing the demand for salt usage.

Clinical-grade quality platelet-rich plasma releasate (PRP-R/SRGF) from CaCl2 -activated platelet concentrates promoted expansion of mesenchymal stromal cells.

PubMed

Borghese, C; Agostini, F; Durante, C; Colombatti, A; Mazzucato, M; Aldinucci, D

2016-08-01

The aim of our study was to test a platelet-rich plasma releasate (PRP-R/SRGF) from CaCl2 -activated platelets as a source of growth factors for the expansion of mesenchymal stromal cells (MSCs). PRP-R/SRGF, obtained with a low-cost procedure, is characterized by a reduced variability of growth factor release. PRP-R/SRGF is a clinical-grade quality solution obtained from CaCl2 -activated platelets. Its activity was evaluated by measuring the proliferation, the phenotype, the differentiation potential and the immunosuppressive properties of MSCs derived from bone marrow (BM) and adipose tissue (AT). PRP-R/SRGF was more active than FBS to expand BM- and AT-derived MSCs. PRP-R/SRGF treatment did not affect the expression of typical MSCs surface markers, neither MSCs differentiation potential nor their capability to inhibit activated T-cell proliferation. The clinical-grade PRP-R/SRGF may be used in the clinical setting for the expansion of MSCs. © 2016 International Society of Blood Transfusion.

Facilitated transport of Cu with hydroxyapatite nanoparticles in saturated sand: Effects of solution ionic strength and composition

USDA-ARS?s Scientific Manuscript database

Column experiments were conducted to investigate the facilitated transport of Cu in association with hydroxyapatite nanoparticles (nHAP) in water-saturated quartz sand at different solution concentrations of NaCl (0 to 100 mM) or CaCl2 (0.1 to 1.0 mM). The experimental breakthrough curves and retent...

Lowering the environmental impact of high-kappa/ metal gate stack surface preparation processes

NASA Astrophysics Data System (ADS)

Zamani, Davoud

ABSTRACT Hafnium based oxides and silicates are promising high-κ dielectrics to replace SiO2 as gate material for state-of-the-art semiconductor devices. However, integrating these new high-κ materials into the existing complementary metal-oxide semiconductor (CMOS) process remains a challenge. One particular area of concern is the use of large amounts of HF during wet etching of hafnium based oxides and silicates. The patterning of thin films of these materials is accomplished by wet etching in HF solutions. The use of HF allows dissolution of hafnium as an anionic fluoride complex. Etch selectivity with respect to SiO2 is achieved by appropriately diluting the solutions and using slightly elevated temperatures. From an ESH point of view, it would be beneficial to develop methods which would lower the use of HF. The first objective of this study is to find new chemistries and developments of new wet etch methods to reduce fluoride consumption during wet etching of hafnium based high-κ materials. Another related issue with major environmental impact is the usage of large amounts of rinsing water for removal of HF in post-etch cleaning step. Both of these require a better understanding of the HF interaction with the high-κ surface during the etching, cleaning, and rinsing processes. During the rinse, the cleaning chemical is removed from the wafers. Ensuring optimal resource usage and cycle time during the rinse requires a sound understanding and quantitative description of the transport effects that dominate the removal rate of the cleaning chemicals from the surfaces. Multiple processes, such as desorption and re-adsorption, diffusion, migration and convection, all factor into the removal rate of the cleaning chemical during the rinse. Any of these processes can be the removal rate limiting process, the bottleneck of the rinse. In fact, the process limiting the removal rate generally changes as the rinse progresses, offering the opportunity to save resources. The second objective of this study is to develop new rinse methods to reduce water and energy usage during rinsing and cleaning of hafnium based high-κ materials in single wafer-cleaning tools. It is necessary to have a metrology method which can study the effect of all process parameters that affect the rinsing by knowing surface concentration of contaminants in patterned hafnium based oxides and silicate wafers. This has been achieved by the introduction of a metrology method at The University of Arizona which monitors the transport of contaminant concentrations inside micro- and nano- structures. This is the only metrology which will be able to provide surface concentration of contaminants inside hafnium based oxides and silicate micro-structures while the rinsing process is taking place. The goal of this research is to study the effect of various process parameters on rinsing of patterned hafnium based oxides and silicate wafers, and modify a metrology method for end point detection.

Porous Proton- and Chloride-Ion Conducting Layers Based on Ethanolamine Derivatives of PVC on the Surfaces of Fabrics

NASA Astrophysics Data System (ADS)

Tsivadze, A. Yu.; Fridman, A. Ya.; Morozova, E. M.; Sokolova, N. P.; Voloshchuk, A. M.; Bardyshev, I. I.; Gorbunov, A. M.; Novikov, A. K.; Polyakova, I. Ya.; Titova, B. N.; Yavich, A. A.

2018-02-01

Materials are produced with porous layers based on ethanolamine derivatives of PVC or compounds of active carbon with hydroxyethylcyclam derivatives of PVC with aqua complexes of chloride hydrogen cross-linked with the surface of cellulose or asbestos fabric. Their capacity for sorption with respect to hexane and benzene in the saturated vapor and liquid phases is determined. The dependences of current on voltage in a circuit are determined for bridges composed of these materials in air, and in the vapor and liquid phases of benzene and hexane between 3 M HCl solutions and 3 M HCl solutions containing 3 M CaCl2. It is established that only H+ ions migrate along the bridges between the HCl solutions, and H+ and Cl- ions were the only species that moved along the bridges between the HCl solutions containing CaCl2. The voltages at which the movement of ions starts are determined, and constants characterizing the conductivity of the layers are found. It is shown that these parameters depend on the structure of a layer, the nature of the fabric, and the medium surrounding a bridge.

Ion-pairing in aqueous CaCl 2 and RbBr solutions. Simultaneous structural refinement of XAFS and XRD data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pham, Thai V.; Fulton, John L.

2013-01-22

We present a new methodology involving the simultaneous refinement of both x-ray absorption and x-ray diffraction spectra (X-ray Absorption/Diffraction Structural Refinement,XADSR), to study hydration and ion pair structure of CaCl 2 and RbBr salts in concentrated aqueous solutions. The XADSR analysis includes the XAFS spectra analysis of both the cation and anion as a probe of their short-range structure with an XRD spectral analysis as a probe of the global structural. Together they deliver a comprehensive picture of the cation and anion hydration, the contact ion pair (CIP) structure and the solvent-separated ion pair (SSIP) structure. XADSR analysis of 6.0more » m aqueous CaCl 2 reveals that there are an insignificant number of Ca 2+-Cl- CIP’s, but there are approximately 3.4 SSIP’s separated by about 4.99 Å. In contrast XADSR analysis of aqueous RbBr yields about 0.7 pair CIP at a bond length 3.51 Å. The present work demonstrates a new approach for a direct co-refinement of XRD and XAFS spectra in a simple and reliable fashion, opening new opportunities for analysis in various disordered and crystalline systems. This work was supported by the U.S. Department of Energy (DOE), Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences. Pacific Northwest National Laboratory (PNNL) is operated for the U.S. Department of Energy by Battelle.« less

Mouth rinsing with a carbohydrate solution attenuates exercise-induced decline in executive function.

PubMed

Konishi, Kana; Kimura, Tetsuya; Yuhaku, Atsushi; Kurihara, Toshiyuki; Fujimoto, Masahiro; Hamaoka, Takafumi; Sanada, Kiyoshi

2017-01-01

A decline in executive function could have a negative influence on the control of actions in dynamic situations, such as sports activities. Mouth rinsing with a carbohydrate solution could serve as an effective treatment for preserving the executive function in exercise. The purpose of this study was to examine the effects of mouth rinsing with a carbohydrate solution on executive function after sustained moderately high-intensity exercise. Eight young healthy participants completed 65 min of running at 75% V̇O 2 max with two mouth-rinsing conditions: with a carbohydrate solution (CHO) or with water (CON). Executive function was assessed before and after exercise by using the incongruent task of the Stroop Color and Word Test. The levels of blood glucose; and plasma adrenocorticotropic hormone (ACTH), epinephrine, and norepinephrine (NE) were evaluated. A two-way repeated-measures ANOVA, with condition (CHO and CON) and time (pre-exercise and post-exercise) as factors, was used to examine the main and interaction effects on the outcome measures. The reaction time in the incongruent condition of the Stroop test significantly increased after exercise in CON (pre-exercise 529 ± 45 ms vs. post-exercise 547 ± 60 ms, P  = 0.029) but not in CHO (pre-exercise 531 ± 54 ms vs. post-exercise 522 ± 80 ms), which resulted in a significant interaction (condition × time) on the reaction time ( P  = 0.028). The increased reaction time in CON indicates a decline in the executive function, which was attenuated in CHO. Increases in plasma epinephrine and NE levels demonstrated a trend toward attenuation accompanying CHO ( P  < 0.085), which appeared to be associated with the preservation of executive function. The blood glucose concentration showed neither significant interactions nor main effects of condition. These findings indicate that mouth rinsing with a carbohydrate solution attenuated the decline in executive function induced by sustained moderately high-intensity exercise, and that such attenuation seems to be unrelated to carbohydrate metabolic pathway but rather attributed, in part, to the inhibition of the excessive release of stress hormones.

High chloride content calcium silicate glasses.

PubMed

Chen, Xiaojing; Karpukhina, Natalia; Brauer, Delia S; Hill, Robert G

2017-03-08

Chloride is known to volatilize from silicate glass melts and until now, only a limited number of studies on oxychloride silicate glasses have been reported. In this paper we have synthesized silicate glasses that retain large amounts of CaCl 2 . The CaCl 2 has been added to the calcium metasilicate composition (CaO·SiO 2 ). Glasses were produced via a melt quench route and an average of 70% of the chloride was retained after melting. Up to 31.6 mol% CaCl 2 has been successfully incorporated into these silicate glasses without the occurrence of crystallization. 29 Si MAS-NMR spectra showed the silicon being present mainly as a Q 2 silicate species. This suggests that chloride formed Cl-Ca(n) species, rather than Si-Cl bonds. Upon increasing the CaCl 2 content, the T g reduced markedly from 782 °C to 370 °C. Glass density and glass crystallization temperature decreased linearly with an increase in the CaCl 2 content. However, both linear regressions revealed a breakpoint at a CaCl 2 content just below 20 mol%. This might be attributed to a significant change in the structure and is also correlated with the nature of the crystallizing phases formed upon heat treatment. The glasses with less than 19.2 mol% CaCl 2 crystallized to wollastonite, whilst the compositions with CaCl 2 content equal to or greater than 19.2 mol% are thought to crystallize to CaCl 2 . In practice, the crystallization of CaCl 2 could not occur until the crystallization temperature fell below the melting point of CaCl 2 . The implications of the results along with the high chloride retention are discussed.

Investigation of phase stability of poly(1-oxotrimethylene)-dissolved aqueous solutions containing ZnCl2/CaCl2/LiCl: Influence of boric acid introduction and aging time

NASA Astrophysics Data System (ADS)

Chae, Dong Wook; Jang, Han Beol; Kim, Byoung Chul

2018-02-01

Poly(1-oxotrimethylene) (POTM) was dissolved in aqueous solutions containing ZnCl2, CaCl2, and LiCl, and the effects of boric acid introduction on the phase stability of the POTM solutions over various aging times were investigated. In the absence of boric acid, aging at 70°C for 8 h notably reduced the loss tangent (tanδ) for the 7.0 wt.% POTM solutions. Addition of boric acid into unaged solutions had little effect on tanδ over the frequency range measured, regardless of its content, whereas addition of 0.3-1.0 wt.% of boric acid into aged solutions increased tanδ. The dynamic viscosity of the POTM solutions with 1.0 wt.% boric acid was affected little by aging time. Conversely, the POTM solutions without boric acid exhibited increased dynamic viscosity in the low-frequency range with aging time. In addition, the slope of the solutions in the Cole-Cole plot decreased with increasing aging time in the absence of boric acid, whereas aging time had little effect in the presence of 1.0 wt.% boric acid. For dilute POTM solutions ( i.e., 0.5 g/dL), the reduced viscosity decreased with increasing aging time in the absence of boric acid, while it was affected little in solutions with the addition of 1.0 wt.% boric acid. In the UV-Vis spectra, the aging-time-dependent increase of the absorbance peak at 390 nm was associated with the generation of a chromophoric complex in the POTM solutions. Conversely, the disappearance of the peak due to the addition of boric acid indicated suppression of complex formation.

Gravity and the membrane-solution interface: theoretical investigations.

PubMed

Schatz, A; Linke-Hommes, A

1989-01-01

The theory of concentration and potential variations at interfaces is applied to the membrane-solution interface to calculate density variations. The theory is modified to take care of the finite ion volumes in electrolytes. Our model is a phospholipid membrane with a surface charge density of -4.824*10(-6)(As/cm2) in contact with solutions of KCl, NaCl, CaCl2, and mixtures. Maximal density variations of about 4*10(-2)(G/cm3) were found in surface layers between the membrane and the solutions. The extension of the layers is in the range of 1 to 6 nm.

Inhibition of Tryptophan on AA 2024 in Chloride-Containing Solutions

NASA Astrophysics Data System (ADS)

Li, Xing; Xiang, Bin; Zuo, Xiu-Li; Wang, Qin; Wei, Zi-Dong

2011-03-01

The inhibitory effects of tryptophan on the corrosion of AA 2024 in 1 M HCl, 20% (wt.%) CaCl2, and 3.5% (wt.%) NaCl solutions were investigated via polarization techniques, electrochemical impedance spectroscopy, and weight loss methods. The scanning electron microscope technique was employed to observe corrosion morphology. The results suggest that AA 2024 was corroded in these three corrosive media to some extent and that tryptophan can significantly inhibit the corrosion of aluminum alloys. The inhibition efficiency (η) increased with increasing concentrations of tryptophan, and the best inhibition efficiency exhibited was about 87% in 1 M HCl solution with 0.008 M tryptophan. Tryptophan acted as a cathodic corrosion inhibitor and affected the hydrogen evolution reaction, which was the main electrode reaction in the 1 M HCl solution. In solutions with 20% CaCl2 and 3.5% NaCl, tryptophan was adsorbed onto anodic areas, thus increasing the activation energy of the interface reaction as an anodic corrosion inhibitor. The Dmol3 program of Material Studio 4.0 was used to obtain the optimized geometry of the tryptophan inhibitor and some quantum-chemical parameters. Front orbital distributions and Fukui indices indicate that the molecular active reaction zones were located in the indole ring of tryptophan.

Modacrylic anion-exchange fibers for Cr(VI) removal from chromium-plating rinse water in batch and flow-through column experiments.

PubMed

Lee, Seung-Chan; Kang, Jin-Kyu; Sim, Eun-Hye; Choi, Nag-Choul; Kim, Song-Bae

2017-11-10

The aim of this study was to investigate Cr(VI) removal from chromium-plating rinse water using modacrylic anion-exchange fibers (KaracaronTM KC31). Batch experiments were performed with synthetic Cr(VI) solutions to characterize the KC31 fibers in Cr(VI) removal. Cr(VI) removal by the fibers was affected by solution pH; the Cr(VI) removal capacity was the highest at pH 2 and decreased gradually with a pH increase from 2 to 12. In regeneration and reuse experiments, the Cr(VI) removal capacity remained above 37.0 mg g -1 over five adsorption-desorption cycles, demonstrating that the fibers could be successfully regenerated with NaCl solution and reused. The maximum Cr(VI) removal capacity was determined to be 250.3 mg g -1 from the Langmuir model. In Fourier-transform infrared spectra, a Cr = O peak newly appeared at 897 cm -1 after Cr(VI) removal, whereas a Cr-O peak was detected at 772 cm -1 due to the association of Cr(VI) ions with ion-exchange sites. X-ray photoelectron spectroscopy analyses demonstrated that Cr(VI) was partially reduced to Cr(III) after the ion exchange on the surfaces of the fibers. Batch experiments with chromium-plating rinse water (Cr(VI) concentration = 1178.8 mg L -1 ) showed that the fibers had a Cr(VI) removal capacity of 28.1-186.4 mg g -1 under the given conditions (fiber dose = 1-10 g L -1 ). Column experiments (column length = 10 cm, inner diameter = 2.5 cm) were conducted to examine Cr(VI) removal from chromium-plating rinse water by the fibers under flow-through column conditions. The Cr(VI) removal capacities for the fibers at flow rates of 0.5 and 1.0 mL min -1 were 214.8 and 171.5 mg g -1 , respectively. This study demonstrates that KC31 fibers are effective in the removal of Cr(VI) ions from chromium-plating rinse water.

Consumer Acceptability of Cucumber Pickles Produced by Fermentation in Calcium Chloride Brine for Reduced Environmental Impact.

PubMed

Wilson, Emily M; Johanningsmeier, Suzanne D; Osborne, Jason A

2015-06-01

Fermentation of cucumbers in calcium chloride (CaCl2 ) brine has been proposed as an alternative process to reduce the environmental impact of traditional, high salt fermentations. The objective of this research was to determine whether consumer acceptability of pickle products would be impacted by fermentation and storage of cucumbers in CaCl2 brine. Cucumbers were fermented and stored with 0.1M CaCl2 or 1M sodium chloride (NaCl) in open-air, 3000 gal tanks at a commercial facility and processed into hamburger dill chips containing 0.38M NaCl. Cucumbers fermented in CaCl2 required additional desalting to reduce CaCl2 concentrations to that of current products. Consumers (n = 101) showed no significant preference for pickles from different fermentation treatments, whether stored for 2 mo (P = 0.75) or 8 mo (P = 0.68) prior to processing. In contrast, NaCl fermented pickles were preferred over CaCl2 fermented pickles stored for 10 mo and desalted only once (P < 0.01). A series of preference tests indicated that the taste of CaCl2 was not the factor affecting consumer preference, and the 50% detection threshold of CaCl2 in dill pickle chips was found to be 61.8 ± 7.6 mM, indicating that processors could potentially use CaCl2 fermentations with a single desalting step. Consumer liking of flavor (n = 73) was not influenced by fermentation in CaCl2 or by 23 or 35 mM CaCl2 in finished products (P > 0.05), but variability in texture decreased consumer liking (P < 0.05). Although promising, individual fermentation variability and texture quality of CaCl2 fermented products should be further evaluated prior to broad implementation of this process. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Impact of High Concentration Solutions on Hydraulic Properties of Geosynthetic Clay Liner Materials

PubMed Central

Xue, Qiang; Zhang, Qian; Liu, Lei

2012-01-01

This study focuses on the impact of landfill high concentration solutions erosion on geosynthetic clay liner (GCL) materials permeability. The permeation tests on the GCL, submerged using different kinds of solutions with different concentrations, were carried out systematically by taking these chemical solutions as permeant liquids. Based on seasonal variations of ion concentrations in Chenjiachong landfill leachate (Wuhan Province), CaCl2, MgCl2, NaCl, and KCl were selected as chemical attack solutions to carry out experimental investigations under three concentrations (50 mM, 100 mM, 200 mM) and soak times (5, 10, and 20 days). The variation law of the GCL hydraulic conductivity under different operating conditions was analyzed. The relationship between GCL hydraulic conductivity, chemical solutions categories, concentrations, and soak times were further discussed. The GCL hydraulic conductivity, when soaked and permeated with high concentration chemical solutions, increases several times or exceeds two orders of magnitude, as compared with the permeation test under normal conditions that used water as the permeant liquid. This reveals that GCL is very susceptible to chemical attack. For four chemical solutions, the chemical attack effect on GCL hydraulic conductivity is CaCl2 > MgCl2 > KCl > NaCl. The impact of soak times on GCL hydraulic conductivity is the cooperative contribution of the liner chemical attack reaction and hydration swelling. A longer soak time results in a more advantageous hydration swelling effect. The chemical attack reaction restrains the hydration swelling of the GCL. Moreover, the GCL hydraulic conductivity exponentially decreases with the increased amplitude of thickness.

Cleaning method and apparatus

DOEpatents

Jackson, Darryl D.; Hollen, Robert M.

1983-01-01

A new automatable cleaning apparatus which makes use of a method of very thoroughly and quickly cleaning a gauze electrode used in chemical analyses is given. The method generates very little waste solution, and this is very important in analyzing radioactive materials, especially in aqueous solutions. The cleaning apparatus can be used in a larger, fully automated controlled potential coulometric apparatus. About 99.98% of a 5 mg. plutonium sample was removed in less than 3 minutes, using only about 60 ml. of rinse solution and two main rinse steps.

Blood coagulation screening using a paper-based microfluidic lateral flow device.

PubMed

Li, H; Han, D; Pauletti, G M; Steckl, A J

2014-10-21

A simple approach to the evaluation of blood coagulation using a microfluidic paper-based lateral flow assay (LFA) device for point-of-care (POC) and self-monitoring screening is reported. The device utilizes whole blood, without the need for prior separation of plasma from red blood cells (RBC). Experiments were performed using animal (rabbit) blood treated with trisodium citrate to prevent coagulation. CaCl2 solutions of varying concentrations are added to citrated blood, producing Ca(2+) ions to re-establish the coagulation cascade and mimic different blood coagulation abilities in vitro. Blood samples are dispensed into a paper-based LFA device consisting of sample pad, analytical membrane and wicking pad. The porous nature of the cellulose membrane separates the aqueous plasma component from the large blood cells. Since the viscosity of blood changes with its coagulation ability, the distance RBCs travel in the membrane in a given time can be related to the blood clotting time. The distance of the RBC front is found to decrease linearly with increasing CaCl2 concentration, with a travel rate decreasing from 3.25 mm min(-1) for no added CaCl2 to 2.2 mm min(-1) for 500 mM solution. Compared to conventional plasma clotting analyzers, the LFA device is much simpler and it provides a significantly larger linear range of measurement. Using the red colour of RBCs as a visible marker, this approach can be utilized to produce a simple and clear indicator of whether the blood condition is within the appropriate range for the patient's condition.

Low-level (PPB) determination of cisplatin in cleaning validation (rinse water) samples. II. A high-performance liquid chromatographic method.

PubMed

Raghavan, R; Burchett, M; Loffredo, D; Mulligan, J A

2000-04-01

A high-performance liquid chromatographic (HPLC) method is described for the determination of residual levels of cisplatin from extracts of surfaces with very low surface area; from extracts of surfaces of coupons made of Teflon (polytetrafluoroethylene, PTFE), stainless steel, and glass; and in aqueous solution collected after rinsing equipment and parts. Initially, the method was developed to determine cisplatin at concentrations ranging from 20 to 200 ng/ml by direct injection. Retaining the same method conditions, the scope of the method was expanded by the addition of a sample preconcentration step, allowing analyses at levels ranging from 0.5 ng to 20 ng/ml. Preconcentration is necessary for the determination of cisplatin in rinse waters at a quantifiable concentration of about 2 PPB. Under these conditions, the detection limit is about 0.2 to 0.3 ng/ml. Residual cisplatin on different types of surfaces, including surfaces with very low surface area, can be determined by swabbing each test surface with a derivatizing solution. The cisplatin recovered in the swabbing solution can be analyzed by HPLC using direct injection or preconcentration, depending on the expected level of cisplatin in the sample. Initial methods were developed to quantitate at a cisplatin concentration of about 100 PPB or higher in solution extracted from surfaces. However, when surface areas are limited because of the size of the parts, solution concentration becomes very low as a result of the minimum volume required for extraction. To support the application of swabbing techniques to surface analysis, stainless steel, Teflon, and glass surfaces were spiked with cisplatin at 2.5 to 20 ng/cm2. Satisfactory overall recoveries of 90% +/- 10% were obtained from all surfaces. Cisplatin has no ultraviolet/visible (UV/Vis) spectral-active functional group that can be used to detect low levels of cisplatin. Hence, diethyldithiocarbamate (DDTC) was used as a derivatizing agent to increase sensitivity to UV absorption at 340 nm. Diethyldithiocarbamate forms complexes with the platinum in cisplatin to yield a platinum-DDTC (Pt-DDTC) complex with a high molar-extinction coefficient. The Pt(DDTC)2 complex thus formed was chromatographically separated and the quantitated by comparison of its detector response to that of a similarly derivatized standard preparation. DDTC also has application as a cleaning agent for cisplatin (e.g., for production equipment cleaning, spill cleanup). Destruction of cisplatin can be affected by the reaction of cisplatin with this cleaning agent. Derivatization of cisplatin will convert active cisplatin to platinum-DDTC on surfaces or in solution. Final cleaning can be accomplished using a water-for-injection rinse. After such a cleaning process, the rinse water, when collected and analyzed, showed levels of free cisplatin less than the detection concentration of 0.2 PPB and a total platinum concentration less than 10 PPB as Pt-DDTC complex.

Effects of Sodium Chloride, Potassium Chloride and Calcium Chloride on the Formation of α-Dicarbonyl Compounds, Furfurals and Development of Browning in Cookies during Baking.

PubMed

Kocadağlı, Tolgahan; Gökmen, Vural

2016-10-02

Effect of NaCl, KCl, CaCl2, NaHCO3, and NH4HCO3 on the formation of glucosone, 1-deoxyglucosone, 3-deoxyglucosone, glyoxal, methylglyoxal, diacetyl, 5-hydroxymethyl-2-furfural, 2-furfural and browning were investigated in cookies. Presence of 1.5% NaCl, 1% KCl, and 1% CaCl2 on flour basis had no effect on α-dicarbonyl compounds, except 1-deoxyglucosone increased in the presence of KCl and CaCl2. The increase in 5-hydroxymethyl-2-furfural formation in the presence of NaCl, KCl, and CaCl2 did not relate to 3-deoxyglucosone formation and pH changes. NaCl, KCl, and CaCl2 increased browning in cookies. Model reaction systems indicated that NaCl, KCl, and CaCl2 enhance browning by increasing furfurals in caramelization. NaCl, KCl, and CaCl2 decreased browning intensity in heated glucose-glycine system. Usage of CaCl2 in cookies may considerably increase furfurals but not α-dicarbonyl compounds. Sodium reduction can be obtained by replacement with potassium without sacrificing the desired consequences of caramelization in sugar rich bakeries.

The effect of a solid surface on the segregation and melting of salt hydrates.

PubMed

Zhang, Yu; Anim-Danso, Emmanuel; Dhinojwala, Ali

2014-10-22

Considering the importance of salt and water on earth, the crystallization of salt hydrates next to solid surfaces has important implications in physical and biological sciences. Heterogeneous nucleation is driven by surface interactions, but our understanding of hydrate formation near surfaces is limited. Here, we have studied the hydrate formation of three commonly prevalent salts, MgCl2, CaCl2, and NaCl, next to a sapphire substrate using surface sensitive infrared-visible sum frequency generation (SFG) spectroscopy. SFG spectroscopy can detect the crystallization and melting of salt hydrates at the interface by observing the changes in the intensity and the location of the cocrystallized water hydroxyl peaks (3200-3600 cm(-1)). The results indicate that the surface crystal structures of these three hydrates are similar to those in the bulk. For the NaCl solution, the brine solution is segregated next to the sapphire substrate after the formation of the ice phase. In contrast, the MgCl2 and CaCl2 surface hydrate crystals are interdispersed with nanometer-size ice crystals. The nanosize ice crystals melt at much lower temperatures than bulk ice crystals. For NaCl and MgCl2 solution, the NaCl hydrates prefer to crystallize next to the sapphire substrate instead of the ice crystals and MgCl2 hydrates.

Regeneration of high-quality silk fibroin fiber by wet spinning from CaCl2-formic acid solvent.

PubMed

Zhang, Feng; Lu, Qiang; Yue, Xiaoxiao; Zuo, Baoqi; Qin, Mingde; Li, Fang; Kaplan, David L; Zhang, Xueguang

2015-01-01

Silks spun by silkworms and spiders feature outstanding mechanical properties despite being spun under benign conditions. The superior physical properties of silk are closely related to its complicated hierarchical structures constructed from nanoscale building blocks, such as nanocrystals and nanofibrils. Here, we report a novel silk dissolution behavior, which preserved nanofibrils in CaCl2-formic acid solution, that enables spinning of high-quality fibers with a hierarchical structure. This process is characterized by simplicity, high efficiency, low cost, environmental compatibility and large-scale industrialization potential, as well as having utility and potential for the recycling of silk waste and the production of silk-based functional materials. Copyright © 2014. Published by Elsevier Ltd.

Remediation of cadmium- and lead-contaminated agricultural soil by composite washing with chlorides and citric acid.

PubMed

Li, Yu-jiao; Hu, Peng-jie; Zhao, Jie; Dong, Chang-xun

2015-04-01

Composite washing of cadmium (Cd)- and lead (Pb)-contaminated agricultural soil from Hunan province in China using mixtures of chlorides (FeCl3, CaCl2) and citric acid (CA) was investigated. The concentrations of composite washing agents for metal removal were optimized. Sequential extraction was conducted to study the changes in metal fractions after soil washing. The removal of two metals at optimum concentration was reached. Using FeCl3 mixed with CA, 44% of Cd and 23% of Pb were removed, and 49 and 32% by CaCl2 mixed with CA, respectively. The mechanism of composite washing was postulated. A mixture of chlorides and CA enhanced metal extraction from soil through the formation of metal-chloride and metal-citrate complexes. CA in extract solutions promoted the formation of metal-chloride complexes and reduced the solution pH. Composite washing reduced Cd and Pb in Fe-Mn oxide forms significantly. Chlorides and CA exerted a synergistic effect on metal extraction during composite washing.

The Effect of fluid buoyancy and fracture orientation on CaCO3 Formation in a Fracture

NASA Astrophysics Data System (ADS)

Xu, Z.; Li, Q.; Sheets, J.; Kneafsey, T. J.; Jun, Y. S.; Cole, D. R.; Pyrak-Nolte, L. J.

2016-12-01

Sealing fractures through mineral precipitation is a potential way for improving caprock integrity in subsurface reservoirs. We investigated the effect of buoyancy and fracture orientation on the amount and spatial distribution of calcium carbonate (CaCO3) precipitates in a fracture. To monitor mineral precipitation during reactive flow, transparent acrylic casts of an induced fracture in Austin chalk were used. To trigger CaCO3 precipitates, 1M CaCl2 with either 0.6M NaHCO3 solution (for surface adhering precipitation), or 0.3M Na2CO3 solution (for pore filling precipitation) were injected simultaneously into a saturated fracture. Experiments were performed with the fracture plane oriented either parallel or perpendicular to gravity. Acoustic wave transmission (compressional wave, 1 MHz) and optical imaging were used to monitor the sample prior to, during and after fluid injection. Complementary X-ray computed tomography was performed throughout the experiments on vertical fractures and post injection for the horizontal fractures. For the vertical fractures, the denser CaCl2 almost completely displaced the carbonate solution in the fracture and caused strong localization of the precipitates. The width of the precipitated region grew slowly over time. The horizontal fracture caused the less dense carbonate to flow over the CaCl2 solution thus resulting in more mixing and a more even distribution of precipitates throughout the fracture. The acoustic signatures depended on the type of precipitation that occurred. For pore filling experiments, the compressional wave amplitude increased by 5-20% and the velocity increased for both the vertical and horizontal fractures. However, the acoustic responses differed between the vertical and horizontal fractures for surface adhering experiments. Based on the acoustic response, surface adhering precipitation increased fracture specific stiffness more in the horizontal fracture than in the vertical fracture. The horizontal fracture enabled more mixing of the two solutions within the fracture than the vertical fracture. This work was supported by the Center for Nanoscale Controls on Geologic CO (NCGC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-AC02-05CH11231

Recycling positive-electrode material of a lithium-ion battery

DOEpatents

Sloop, Steven E.

2017-11-21

Examples are disclosed of methods to recycle positive-electrode material of a lithium-ion battery. In one example, the positive-electrode material is heated under pressure in a concentrated lithium hydroxide solution. After heating, the positive-electrode material is separated from the concentrated lithium hydroxide solution. After separating, the positive electrode material is rinsed in a basic liquid. After rinsing, the positive-electrode material is dried and sintered.

Analysis of the effectiveness of Sodium Hypochlorite decontamination of cadaveric human tissues at retrieval.

PubMed

Paolin, Adolfo; Trojan, Diletta; Carniato, Antonio; Tasca, Fabio; Massarin, Ervino; Tugnoli, Alessandro; Cogliati, Elisa

2016-12-01

Bacterial contamination of tissues retrieved from cadaveric donors is a common feature worldwide, and every tissue bank, albeit using different methods, conducts decontamination to guarantee safe tissues suitable for clinical use. The effectiveness of the methods used to eradicate pathogens differs. In order to reduce the tissue bioburden at retrieval, we have introduced a new method involving rinsing tissues in a sodium hypochlorite solution. To test its effectiveness we analyzed two comparable groups of tissues: Group A: 1881 tissues, all rinsed with isotonic saline solution after retrieval, and Group B: 1968 tissues immersed in an isotonic saline solution containing sodium hypochlorite (final concentration 0.1 %) for different lengths of time and subsequently rinsed with isotonic saline. The rinsing solution of each tissue was then sampled for microbiological cultures in both groups. The resultant overall contamination rate was 40.5 % for Group A and 6.7 % for Group B, with an 82.8 % difference in the reduction of contamination between the two groups. This was especially the case for commensal skin bacteria in musculoskeletal tissue, which accounted for over half the overall contamination. Our data highlighted that decontamination with sodium hypochlorite was helpful in reducing the bacterial bioburden in tissues retrieved from cadaveric donors.

Important role of calcium chloride in preventing carbon monoxide generation during desflurane degradation with alkali hydroxide-free carbon dioxide absorbents.

PubMed

Ando, Takahiro; Mori, Atsushi; Ito, Rie; Nishiwaki, Kimitoshi

2017-12-01

We investigated whether calcium chloride (CaCl 2 ), a supplementary additive in carbon dioxide (CO 2 ) absorbents, could affect carbon monoxide (CO) production caused by desflurane degradation, using a Japanese alkali-free CO 2 absorbent Yabashi Lime ® -f (YL-f), its CaCl 2 -free and 1% CaCl 2 -added derivatives, and other commercially available alkali-free absorbents with or without CaCl 2 . The reaction between 1 L of desflurane gas (3-10%) and 20 g of desiccated specimen was performed in an artificial closed-circuit anesthesia system for 3 min at 20 or 40 °C. The CO concentration was measured using a gas chromatograph equipped with a semiconductor sensor detector. The systems were validated by detecting dose-dependent CO production with an alkali hydroxide-containing CO 2 absorbent, Sodasorb ® . Compared with YL-f, the CaCl 2 -free derivative caused the production of significantly more CO, while the 1% CaCl 2 -added derivative caused the production of a comparable amount of CO. These phenomena were confirmed using commercially available absorbents AMSORB ® PLUS, an alkali-free absorbent with CaCl 2 , and LoFloSorb™, an alkali-free absorbent without CaCl 2 . These results suggest that CaCl 2 plays an important role in preventing CO generation caused by desflurane degradation with alkali hydroxide-free CO 2 absorbents like YL-f.

SILANE-BASED CONVERSION COATING FOR METALS

EPA Science Inventory

For the past three years, a project to develop new pretreatment rinses for metals was carried out by the U.S. Environmental Protection Agency and the University of Cincinnati. The project involved optimization of laboratory rinses with dilute aqueous solutions organofunctional s...

Cleaning method and apparatus

DOEpatents

Jackson, D.D.; Hollen, R.M.

1981-02-27

A method of very thoroughly and quikcly cleaning a guaze electrode used in chemical analyses is given, as well as an automobile cleaning apparatus which makes use of the method. The method generates very little waste solution, and this is very important in analyzing radioactive materials, especially in aqueous solutions. The cleaning apparatus can be used in a larger, fully automated controlled potential coulometric apparatus. About 99.98% of a 5 mg plutonium sample was removed in less than 3 minutes, using only about 60 ml of rinse solution and two main rinse steps.

Development of Electrically Conductive Transparent Coatings for Acrylic Plastic

DTIC Science & Technology

1952-12-01

after drying, but increased to 4,000 megoihms/square after 16 hours. 4. Polyacrylic-polyamine Cop-lyrrvrs Aqueous solutions of polymethacrylic acid ...methacrylic acid -methyl methaerylate copolymer re•I. The composite material, i. e., the acrylic and applied coating, retains essentially all the original...ation in 5%, NaOH solution for 5 minutes, rinsed in distilled water, immersed with agitation in 1516 nitric acid for 3 minutes and finally rinsed well

Tunable two-dimensional liquid gradient refractive index (L-GRIN) lens for variable light focusing.

PubMed

Huang, Hua; Mao, Xiaole; Lin, Sz-Chin Steven; Kiraly, Brian; Huang, Yiping; Huang, Tony Jun

2010-09-21

We report a two-dimensional (2D) tunable liquid gradient refractive index (L-GRIN) lens for variable focusing of light in the out-of-plane direction. This lens focuses a light beam through a liquid medium with a 2D hyperbolic secant (HS) refractive index gradient. The refractive index gradient is established in a microfluidic chamber through the diffusion between two fluids with different refractive indices, i.e. CaCl(2) solution and deionized (DI) water. The 2D HS refractive index profile and subsequently the focal length of the L-GRIN lens can be tuned by changing the ratio of the flow rates of the CaCl(2) solution and DI water. The focusing effect is experimentally characterized through side-view and top-view image analysis, and the experimental data match well with the results from ray-tracing optical simulations. Advantages of the 2D L-GRIN lens include simple device fabrication procedure, low fluid consumption rate, convenient lens-tuning mechanism, and compatibility with existing microfluidic devices. We expect that with further optimizations, this 2D L-GRIN lens can be used in many optics-based lab-on-a-chip applications.

Acoustic Monitoring of Gravity-Driven Controls on CaCO3 Precipitates in a Fracture

NASA Astrophysics Data System (ADS)

Xu, Z.; Sheets, J.; Zhang, L.; Kim, D.; Kneafsey, T. J.; Cole, D. R.; Jun, Y. S.; Pyrak-Nolte, L. J.

2017-12-01

Sealing fractures by mineral precipitation is an important process for improving caprock integrity in subsurface reservoirs. In this study, the ability to monitor precipitate distribution in fractures with buoyant fluids was examined. Fractures with uniform aperture distributions of 0.5, 1.0 and 2.0 mm were created from acrylic plates to enable direct imaging of precipitate formation over time. CaCO3 precipitation was induced in a fracture from invasion of 1M CaCl2 and 0.3M Na2CO3 solutions. During chemical invasion, a fracture plane was oriented either parallel or perpendicular to gravity. Acoustic (P) wave transmission ( 1 MHz) and optical imaging were used to monitor the sample prior to, during and after fluid injection. Complementary X-ray computed tomography was performed throughout the experiments on vertical fractures and post injection for the horizontal fractures. Precipitate particle sizes during formation were determined using SAXS and WAXS. In both horizontal and vertical fractures, the density contrast between the two solutions affected the spatial distribution of precipitation. In vertical fractures, the denser CaCl2 solution almost completely displaced the NaCO3 solution, causing strong localization of precipitates. However, in the horizontal fractures, flow stratification occurred in the 2 mm aperture fractures, with the less dense Na2CO3 flowing over the CaCl2 solution, resulting in a more even distribution of precipitates cross the fracture plane. P-wave amplitudes increased up to 8% and the arrival time decreased with precipitate accumulation in the horizontal fracture. This is consistent with a three-layered approach as the seismic impedance inside the fracture increases. The initial contact between the two was observed as a decrease in the P-wave amplitude. As precipitates accumulated, the amplitude recovered and increased, with greater increases observed along the mixing flow path. Fractures in the subsurface may seal differently depending on the orientation thus affecting the ability of a fracture to self-heal if oriented vertically. This work was supported by the Center for Nanoscale Controls on Geologic CO (NCGC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-AC02-05CH11231

Improved Detection Technique for Solvent Rinse Cleanliness Verification

NASA Technical Reports Server (NTRS)

Hornung, S. D.; Beeson, H. D.

2001-01-01

The NASA White Sands Test Facility (WSTF) has an ongoing effort to reduce or eliminate usage of cleaning solvents such as CFC-113 and its replacements. These solvents are used in the final clean and cleanliness verification processes for flight and ground support hardware, especially for oxygen systems where organic contaminants can pose an ignition hazard. For the final cleanliness verification in the standard process, the equivalent of one square foot of surface area of parts is rinsed with the solvent, and the final 100 mL of the rinse is captured. The amount of nonvolatile residue (NVR) in the solvent is determined by weight after the evaporation of the solvent. An improved process of sampling this rinse, developed at WSTF, requires evaporation of less than 2 mL of the solvent to make the cleanliness verification. Small amounts of the solvent are evaporated in a clean stainless steel cup, and the cleanliness of the stainless steel cup is measured using a commercially available surface quality monitor. The effectiveness of this new cleanliness verification technique was compared to the accepted NVR sampling procedures. Testing with known contaminants in solution, such as hydraulic fluid, fluorinated lubricants, and cutting and lubricating oils, was performed to establish a correlation between amount in solution and the process response. This report presents the approach and results and discusses the issues in establishing the surface quality monitor-based cleanliness verification.

New approach to resolve the humidity problem in VOC determination in outdoor air samples using solid adsorbent tubes followed by TD-GC-MS.

PubMed

Maceira, Alba; Vallecillos, Laura; Borrull, Francesc; Marcé, Rosa Maria

2017-12-01

This study describes the humidity effect in the sampling process by adsorbent tubes followed by thermal desorption and gas chromatography-mass spectrometry (TD-GC-MS) for the determination of volatile organic compounds (VOCs) in air samples and evaluates possible solutions to this problem. Two multi-sorbent bed tubes, Tenax TA/Carbograph 1TD and Carbotrap B/Carbopack X/Carboxen 569, were tested in order to evaluate their behaviour in the presence of environmental humidity. Humidity problems were demonstrated with carbon-based tubes, while Tenax-based tubes did not display any influence. Silica gel, a molecular sieve and CaCl 2 were tried out as materials for drying tube to remove air humidity, placed prior to the sampling tube to prevent water from entering. The pre-tubes filled with 0.5g of CaCl 2 showed the best results with respect to their blanks, the analytes recoveries and their ability to remove ambient humidity. To avoid the possible agglomeration of CaCl 2 during the sampling process in high relative humidity atmospheres, 0.1g of diatomaceous earth were mixed with the desiccant agent. The applicability of the CaCl 2 pre-tube as drying agent prior to Carbotrap B/Carbopack X/Carboxen 569 tubes was tested in urban and industrial locations with samplings of air at high relative humidity. In addition, the results were compared with those obtained using Tenax TA/Carbograph 1TD tubes. Copyright © 2017 Elsevier B.V. All rights reserved.

Improving La0.6Sr0.4Co0.8Fe0.2O3-δ infiltrated solid oxide fuel cell cathode performance through precursor solution desiccation

NASA Astrophysics Data System (ADS)

Burye, Theodore E.; Nicholas, Jason D.

2015-02-01

Here, for the first time, the average size of solid oxide fuel cell (SOFC) electrode nano-particles was reduced through the chemical desiccation of infiltrated precursor nitrate solutions. Specifically, after firing at 700 °C, CaCl2-desiccated La0.6Sr0.4Co0.8Fe0.2O3-δ (LSCF) - Ce0.9Gd0.1O1.95 (GDC) cathodes contained LSCF infiltrate particles with an average size of 22 nm. This is in contrast to comparable, undesiccated LSCF-GDC cathodes which contained LSCF infiltrate particles with an average size of 48 nm. X-ray diffraction, scanning electron microscopy, and controlled atmosphere electrochemical impedance spectroscopy revealed that desiccation reduced the average infiltrate particle size without altering the infiltrate phase purity, the cathode concentration polarization resistance, or the cathode electronic resistance. Compared to undesiccated LSCF-GDC cathodes achieving polarization resistances of 0.10 Ωcm2 at 640 °C, comparable CaCl2-dessicated LSCF-GDC cathodes achieved 0.10 Ωcm2 at 575 °C. Mathematical modeling suggested that these performance improvements resulted solely from average infiltrate particle size reductions.

Influence of solution chemistry on the inactivation of particle-associated viruses by UV irradiation.

PubMed

Feng, Zhe; Lu, Ruiqing; Yuan, Baoling; Zhou, Zhenming; Wu, Qingqing; Nguyen, Thanh H

2016-12-01

MS2 inactivation by UV irradiance was investigated with the focus on how the disinfection efficacy is influenced by bacteriophage MS2 aggregation and adsorption to particles in solutions with different compositions. Kaolinite and Microcystis aeruginosa were used as model inorganic and organic particles, respectively. In the absence of model particles, MS2 aggregates formed in either 1mM NaCl at pH=3 or 50-200mM ionic strength CaCl 2 solutions at pH=7 led to a decrease in the MS2 inactivation efficacy because the virions located inside the aggregate were protected from the UV irradiation. In the presence of kaolinite and Microcystis aeruginosa, MS2 adsorbed onto the particles in either 1mM NaCl at pH=3 or 50-200mM CaCl 2 solutions at pH=7. In contrast to MS2 aggregates formed without the presence of particles, more MS2 virions adsorbed on these particles were exposed to UV irradiation to allow an increase in MS2 inactivation. In either 1mM NaCl at pH from 4 to 8 or 2-200mM NaCl solutions at pH=7, the absence of MS2 aggregation and adsorption onto the model particles explained why MS2 inactivation was not influenced by pH, ionic strength, and the presence of model particles in these conditions. The influence of virus adsorption and aggregation on the UV disinfection efficiency found in this research suggests the necessity of accounting for particles and cation composition in virus inactivation for drinking water. Copyright © 2016 Elsevier B.V. All rights reserved.

METHOD OF CHEMICAL DECONTAMINATION OF STAINLESS STEEL NUCLEAR FACILITIES

DOEpatents

Pancer, G.P.; Zegger, J.L.

1961-12-19

A chemical method is given for removing activated corrosion products on the primary system surfaces of a pressurized water reactor. The corrosion product deposits are composed chiefly of magnetite (Fe/sub 3/O/sub 4/) with small amounts of nickel and chromium oxides. The corroded surfaces are first flushed with a caustic permanganate primary solution consisting of sodium hydroxide and potassium permanganate followed by a secondary rinse solution of ammonium citrate and citric acid containing the complexing agent Versene in small amounts. Demineralized water is used to clean out the primary and secondary solutions and a 60-minute drying period precedes the rinse solution. (AEC)

Antimicrobial effect of electrolyzed oxidizing water against Escherichia coli O157:H7 and Listeria monocytogenes on fresh strawberries (Fragaria x ananassa).

PubMed

Udompijitkul, P; Daeschel, M A; Zhao, Y

2007-11-01

Antibacterial activity of electrolyzed oxidizing (EO) water prepared from 0.05% or 0.10% (w/v) sodium chloride (NaCl) solutions against indigenous bacteria associated with fresh strawberries (Fragaria x ananassa) was evaluated. The efficacy of EO water and sodium hypochlorite (NaOCl) solution in eliminating and controlling the growth of Listeria monocytogenes and Escherichia coli O157:H7 inoculated onto strawberries stored at 4 +/- 1 degrees C up to 15 d was investigated at exposure time of 1, 5, or 10 min. Posttreatment neutralization of fruit surfaces was also determined. More than 2 log(10) CFU/g reductions of aerobic mesophiles were obtained in fruits washed for 10 or 15 min in EO water prepared from 0.10% (w/v) NaCl solution. Bactericidal activity of the disinfectants against L. monocytogenes and E. coli O157:H7 was not affected by posttreatment neutralization, and increasing exposure time did not significantly increase the antibacterial efficacy against both pathogens. While washing fruit surfaces with distilled water resulted in 1.90 and 1.27 log(10) CFU/mL of rinse fluid reduction of L. monocytogenes and E. coli O157:H7, respectively, >/= 2.60 log(10) CFU/mL of rinse fluid reduction of L. monocytogenes and up to 2.35 and 3.12 log(10) CFU/mL of rinse fluid reduction of E. coli O157:H7 were observed on fruit surfaces washed with EO water and NaOCl solution, respectively. Listeria monocytogenes and E. coli O157:H7 populations decreased over storage regardless of prior treatment. However, EO water and aqueous NaOCl did not show higher antimicrobial potential than water treatment during refrigeration storage.

Link between alginate reaction front propagation and general reaction diffusion theory.

PubMed

Braschler, Thomas; Valero, Ana; Colella, Ludovica; Pataky, Kristopher; Brugger, Jürgen; Renaud, Philippe

2011-03-15

We provide a common theoretical framework reuniting specific models for the Ca(2+)-alginate system and general reaction diffusion theory along with experimental validation on a microfluidic chip. As a starting point, we use a set of nonlinear, partial differential equations that are traditionally solved numerically: the Mikkelsen-Elgsaeter model. Applying the traveling-wave hypothesis as a major simplification, we obtain an analytical solution. The solution indicates that the fundamental properties of the alginate reaction front are governed by a single dimensionless parameter λ. For small λ values, a large depletion zone accompanies the reaction front. For large λ values, the alginate reacts before having the time to diffuse significantly. We show that the λ parameter is of general importance beyond the alginate model system, as it can be used to classify known solutions for second-order reaction diffusion schemes, along with the novel solution presented here. For experimental validation, we develop a microchip model system, in which the alginate gel formation can be carried out in a highly controlled, essentially 1D environment. The use of a filter barrier enables us to rapidly renew the CaCl(2) solution, while maintaining flow speeds lower than 1 μm/s for the alginate compartment. This allows one to impose an exactly known bulk CaCl(2) concentration and diffusion resistance. This experimental model system, taken together with the theoretical development, enables the determination of the entire set of physicochemical parameters governing the alginate reaction front in a single experiment.

The effect of sodium bicarbonate oral rinse on salivary pH and oral microflora: A prospective cohort study.

PubMed

Chandel, Siddhartha; Khan, Mohsin Ali; Singh, Nishi; Agrawal, Amiya; Khare, Vinita

2017-01-01

Present study is designed to explore the effect of sodium bicarbonate oral rinse on salivary pH and oral micro flora. Twenty five healthy subjects were recruited for the study in department of dentistry in Era Medical College. Subjects were abstained from tooth brushing overnight pre rinse (control) samples were collected after one hour of dinner and were asked to rinse with pre calibrated freshly prepared sodium bicarbonate solution. The salivary samples were then collected the following morning using sterile gauze in marked bottles. Aerobic bacterial culture was done by plating the sample directly from the swab on the surface of Blood agar and Mac Conkeys media respectively. The colony forming units and ph were calculated for the pre rinse and post rinse saliva sample. Results shows that salivary pH increased significantly after sodium Bicarbonate oral rinse. There was a marginal decrease in number of CFU/ml for bacteria especially Viridans Streptococci, Moraxella species. Sodium Bicarbonate oral rinse may be considered as a cheap and effective alternative for chlorhexidine and alcohol based mouth wash, especially where long duration usage is required.

Rinsing with antacid suspension reduces hydrochloric acid-induced erosion.

PubMed

Alves, Maria do Socorro Coelho; Mantilla, Taís Fonseca; Bridi, Enrico Coser; Basting, Roberta Tarkany; França, Fabiana Mantovani Gomes; Amaral, Flávia Lucisano Botelho; Turssi, Cecilia Pedroso

2016-01-01

Mouthrinsing with antacids, following erosive episodes, have been suggested as a preventative strategy to minimize tooth surface loss due to their neutralizing effect. The purpose of this in situ study was to evaluate the effect of an antacid suspension containing sodium alginate, sodium bicarbonate and calcium carbonate in controlling simulated erosion of enamel of intrinsic origin. The experimental units were 48 slabs (3×3×2mm) of bovine enamel, randomly divided among 12 volunteers who wore palatal appliances with two enamel slabs. One of them was exposed extra-orally twice a day to 25mL of a hydrochloric acid (HCl) solution (0.01M, pH 2) for 2min. There were two independent phases, lasting 5 days each. In the first phase, according to a random scheme, half of the participants rinsed with 10mL of antacid suspension (Gaviscon(®), Reckitt Benckiser Healthcare Ltd.), while the remainder was rinsed with deionized water, for 1min. For the second phase, new slabs were inserted and participants switched to the treatment not received in the first stage. Therefore, the groups were as follows: (a) erosive challenge with HCl+antacid suspension; (b) erosive challenge with HCl+deionized water (DIW); (c) no erosive challenge+antacid suspension; (d) no erosive challenge+DIW. Specimens were assessed in terms of surface loss using optical profilometry and Knoop microhardness. The data were analyzed using repeated measures two-way analysis of variance and Tukey's tests. Compared to DIW rinses, surface loss of enamel was significantly lower when using an antacid rinse following erosive challenges (p=0.015). The Knoop microhardness of the enamel was significantly higher when the antacid rinse was used (p=0.026). The antacid suspension containing sodium alginate, sodium bicarbonate and calcium carbonate, rinsed after erosive challenges of intrinsic origin, reduced enamel surface loss. Copyright © 2015 Elsevier Ltd. All rights reserved.

An In Vitro Evaluation of Leakage of Two Etch and Rinse and Two Self-Etch Adhesives after Thermocycling

PubMed Central

Geerts, Sabine; Bolette, Amandine; Seidel, Laurence; Guéders, Audrey

2012-01-01

Our experiment evaluated the microleakage in resin composite restorations bonded to dental tissues with different adhesive systems. 40 class V cavities were prepared on the facial and lingual surfaces of each tooth with coronal margins in enamel and apical margins in cementum (root dentin). The teeth were restored with Z100 resin composite bonded with different adhesive systems: Scotchbond Multipurpose (SBMP), a 3-step Etch and Rinse adhesive, Adper Scotchbond 1 XT (SB1), a 2-step Etch and Rinse adhesive, AdheSE One (ADSE-1), a 1-step Self-Etch adhesive, and AdheSE (ADSE), a 2-step Self-Etch adhesive. Teeth were thermocycled and immersed in 50% silver nitrate solution. When both interfaces were considered, SBMP has exhibited significantly less microleakage than other adhesive systems (resp., for SB1, ADSE-1 and ADSE, P = 0.0007, P < 0.0001 and P < 0.0001). When enamel and dentin interfaces were evaluated separately, (1) for the Self-Etch adhesives, microleakage was found greater at enamel than at dentin interfaces (for ADSE, P = 0.024 and for ADSE-1, P < 0.0001); (2) for the Etch and Rinse adhesive systems, there was no significant difference between enamel and dentin interfaces; (3) SBMP was found significantly better than other adhesives both at enamel and dentin interfaces. In our experiment Etch and Rinse adhesives remain better than Self-Etch adhesives at enamel interface. In addition, there was no statistical difference between 1-step (ADSE-1) and 2-step (ADSE) Self-Etch adhesives. PMID:22675358

Novel technologies for enhanced production of ethanol: impact of high productivity on process economics

USDA-ARS?s Scientific Manuscript database

In these studies Saccharomyces cerevisiae NRRL Y-566 was used to produce ethanol from a concentrated glucose (250-300 gL-1) solution. When fermentation media were supplemented with CaCO3 and CaCl2, ethanol concentrations, yield, and productivities were improved significantly. In control batch fermen...

Box-Behnken methodology for Cr (VI) and leather dyes removal by an eco-friendly biosorbent: F. vesiculosus.

PubMed

Cobas, M; Sanromán, M A; Pazos, M

2014-05-01

This study focused on leather industrial effluents treatment by biosorption using Fucus vesiculosus as low-cost adsorbent. These effluents are yellowish-brown color and high concentration of Cr (VI). Therefore, biosorption process was optimized using response surface methodology based on Box-Behnken design operating with a simulated leather effluent obtained by mixture of Cr (VI) solution and four leather dyes. The key variables selected were initial solution pH, biomass dosage and CaCl2 concentration in the pretreatment stage. The statistical analysis shows that pH has a negligible effect, being the biomass dosage and CaCl2 concentration the most significant variables. At optimal conditions, 98% of Cr (VI) and 88% of dyes removal can be achieved. Freundlich fitted better to the obtained equilibrium data for all studied systems than Temkin, Langmuir or D-R models. In addition, the use of the final biosorbent as support-substrate to grown of enzyme producer fungi, Pleurotus ostreatus, was also demonstrated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermodynamic description of Tc(iv) solubility and hydrolysis in dilute to concentrated NaCl, MgCl2 and CaCl2 solutions.

PubMed

Yalçıntaş, Ezgi; Gaona, Xavier; Altmaier, Marcus; Dardenne, Kathy; Polly, Robert; Geckeis, Horst

2016-06-07

We present the first systematic investigation of Tc(iv) solubility, hydrolysis and speciation in dilute to concentrated NaCl, MgCl2 and CaCl2 systems, and comprehensive thermodynamic and activity models for the system Tc(4+)-H(+)-Na(+)-Mg(2+)-Ca(2+)-OH(-)-Cl(-)-H2O using both SIT and Pitzer approaches. The results are advancing the fundamental scientific understanding of Tc(iv) solution chemistry and are highly relevant in the applied context of nuclear waste disposal. The solubility of Tc(iv) was investigated in carbonate-free NaCl-NaOH (0.1-5.0 M), MgCl2 (0.25-4.5 M) and CaCl2 (0.25-4.5 M) solutions within 2 ≤ pHm≤ 14.5. Undersaturation solubility experiments were performed under an Ar atmosphere at T = 22 ± 2 °C. Strongly reducing conditions (pe + pHm≤ 2) were imposed with Na2S2O4, SnCl2 and Fe powder to stabilize technetium in the +IV redox state. The predominance of Tc(iv) in the aqueous phase was confirmed by solvent extraction and XANES/EXAFS spectroscopy. Solid phase characterization was accomplished after attaining thermodynamic equilibrium using XRD, SEM-EDS, XANES/EXAFS, TG-DTA and quantitative chemical analysis, and indicated that TcO2·0.6H2O(s) exerts solubility-control in all evaluated systems. The definition of the polyatomic Tc3O5(2+) species instead of TcO(2+) is favoured under acidic conditions, consistently with slope analysis (mTcvs. pHm) of the solubility data gained in this work and spectroscopic evidence previously reported in the literature. The additional formation of Tc(iv)-OH/O-Cl aqueous species in concentrated chloride media ([Cl(-)] = 9 M) and pHm≤ 4 is suggested by solubility and EXAFS data. The pH-independent behaviour of the solubility observed under weakly acidic to weakly alkaline pHm conditions can be explained with the equilibrium reaction TcO2·0.6H2O(s) + 0.4H2O(l) ⇔ TcO(OH)2(aq). Solubility data determined in dilute NaCl systems with pHm≥ 11 follow a well-defined slope of +1, consistent with the predominance of TcO(OH)3(-) previously selected by NEA-TDB. In concentrated MgCl2 and CaCl2 solutions with pHm≥ 8, the formation of the ternary Mg3[TcO(OH)5](3+) and Ca3[TcO(OH)5](3+) species is proposed based on the slope analysis of the solubility data, model calculations and previous observations for analogous An(iv) and Zr(iv) systems. The formation and stability of these hitherto unknown Tc(iv) species are supported by DFT calculations. Based on the newly generated experimental data and previous spectroscopic observations, new comprehensive chemical, thermodynamic and activity models (SIT, Pitzer) for these systems are derived.

Rapid measurement of 89,90Sr radioactivity in rinse water.

PubMed

Masashi, Takada; Hiroko, Enomoto; Toshikazu, Suzuki

2013-03-01

Rapid measurement of radioactivity from Sr in aqueous solutions is performed using a technique combining a strontium rad disk and a picobeta spectrometer. Identification of Sr radionuclides is accomplished in as little as 90 min in a radiation-tainted solution that contains more highly radioactive cesium. It is possible to perform triage by assessing skin exposure doses in this short time. This simple technique could be used in mobile laboratories. Sr having 1 Bq radioactivities are measured in 10 kBq Cs in aqueous solution. The radioactivity contained in rinse water used to decontaminate the feet of workers who stepped into highly contaminated water in the basement of the turbine building of Unit 3 at the Fukushima Daiichi nuclear power station was measured. The amount of Sr radioactivity in rinse water using the authors' rapid measurement technique (0.29 Bq mL) and a traditional method agree well, with 3.6% difference. Based on this agreement, this technique is confirmed to be useful for rapid measurement of Sr radioactivities.

Saliva and tongue coating pH before and after use of mouthwashes and relationship with parameters of halitosis

PubMed Central

TOLENTINO, Elen de Souza; CHINELLATO, Luiz Eduardo Montenegro; TARZIA, Olinda

2011-01-01

Objectives The aim of this work was to evaluate saliva and tongue coating pH in oral healthy patients with morning bad breath before and after use of different oral mouthrinses. Material and Methods aliva and tongue coating pH of 50 patients allocated in 5 groups were measured respectively by a digital pHmeter and color pH indicators, before, immediately after and 30 min after rinsing 5 different mouthrinses: cetilpiridine chloride associated with sodium chloride, triclosan, enzymatic solution, essential oil and distilled water. Results Only triclosan and essential oil increased salivary pH immediately after rising. The enzymatic solution decreased salivary and tongue coating pH immediately after rinsing. Conclusion Salivary pH tended to be acidic while tongue coating pH tended to be alkaline, even after rising. Triclosan and essential oil mouthrinses increased salivary pH immediately after rinsing. Enzymatic solution decreased saliva and tongue coating pH immediately after rising. PMID:21552707

Preparation and release characteristics of polymer-coated and blended alginate microspheres.

PubMed

Lee, D W; Hwang, S J; Park, J B; Park, H J

2003-01-01

To prevent a rapid drug release from alginate microspheres in simulated intestinal media, alginate microspheres were coated or blended with polymers. Three polymers were selected and evaluated such as HPMC, Eudragit RS 30D and chitosan, as both coating materials and additive polymers for controlling the drug release. This study focused on the release characteristics of polymer-coated and blended alginate microspheres, varying the type of polymer and its concentration. The alginate microspheres were prepared by dropping the mixture of drug and sodium alginate into CaCl(2) solution using a spray-gun. Polymer-coated microspheres were prepared by adding alginate microspheres into polymer solution with mild stirring. Polymer-blended microspheres were prepared by dropping the mixture of drug, sodium alginate and additive polymer with plasticizer into CaCl(2) solution. In vitro release test was carried out to investigate the release profiles in 500 ml of phosphate buffered saline (PBS, pH 7.4). As the amount of polymer in sodium alginate or coating solution increase, the drug release generally decreased. HPMC-blended microspheres swelled but withstood the disintegration, showing an ideal linear release profiles. Chitosan-coated microspheres showed smooth and round surface and extended the release of drug. In comparison with chitosan-coated microspheres, HPMC-blended alginate microspheres can be easily made and used for controlled drug delivery systems due to convenient process and controlled drug release.

Rapamycin inhibits CaCl2-induced thoracic aortic aneurysm formation in rats through mTOR-mediated suppression of proinflammatory mediators.

PubMed

Cao, Jiumei; Wu, Qihong; Geng, Liang; Chen, Xiaonan; Shen, Weifeng; Wu, Fang; Chen, Ying

2017-08-01

The aim of the present study was to investigate the effect of the mammalian target of rapamycin (mTOR) signaling pathway on thoracic aortic aneurysm (TAA) development. The study used a calcium chloride (CaCl2)‑induced rat TAA model to explore the potential role of mTOR signaling pathway in the disease development. Adult male Sprague‑Dawley rats underwent the periarterial exposure of thoracic aorta to either 0.5 M CaCl2 or normal saline, and a subgroup of CaCl2‑treated rats received rapamycin 1 day prior to surgery. Without pre‑administering rapamycin, significantly enhanced phosphorylation of mTOR and expression of proinflammatory cytokines [i.e., tumor necrosis factor α (TNF‑α), interleukin 6 (IL‑6), and interleukin (IL)‑1β] were observed in the CaCl2‑treated aortic segments 2 days post‑treatment compared with the NaCl‑treated segments. At 2 weeks post‑treatment, hematoxylin and eosin and Verhoeff‑Van Gieson staining revealed aneurysmal alteration and disappearance of normal wavy elastic structures in the aortic segments exposed to CaCl2. In contrast, the CaCl2‑induced TAA formation was inhibited by pre‑administering rapamycin to CaCl2‑treated rats, which demonstrated attenuated mTOR phosphorylation and downregulation of the proinflammatory mediators (i.e., TNF‑α, IL‑6, IL‑1β, matrix metallopeptidases 2 and 9) to the control level. Further in vitro cell culture experiments using aortic smooth muscle cell (SMC) suggested that the inhibition of the mTOR signaling pathway by rapamycin could promote the differentiation of SMCs, as reflected by the reduced expression of S100A4 and osteopontin. The present study indicated that the early enhanced mTOR signaling pathway in the TAA development and mTOR inhibitor rapamycin may inhibit CaCl2‑induced TAA formation.

Influence of internal composition on physicochemical properties of alginate aqueous-core capsules.

PubMed

Ben Messaoud, Ghazi; Sánchez-González, Laura; Probst, Laurent; Desobry, Stéphane

2016-05-01

To enhance physicochemical properties of alginate aqueous-core capsules, conventional strategies were focused in literature on designing composite and coated capsules. In the present study, own effect of liquid-core composition on mechanical and release properties was investigated. Capsules were prepared by dripping a CaCl2 solution into an alginate gelling solution. Viscosity of CaCl2 solution was adjusted by adding cationic, anionic and non-ionic naturally derived polymers, respectively chitosan, xanthan gum and guar gum. In parallel, uniform alginate hydrogels were prepared by different methods (pouring, in situ forming and mixing). Mechanical stability of capsules and plane hydrogels were respectively evaluated by compression experiments and small amplitude oscillatory shear rheology and then correlated. Capsules permeability was evaluated by monitoring diffusion of encapsulated cochineal dye, riboflavin and BSA. The core-shell interactions were investigated by ATR-FTIR. Results showed that inner polymer had an impact on membrane stability and could act as an internal coating or provide mechanical reinforcement. Mechanical properties of alginate capsules were in a good agreement with rheological behavior of plane hydrogels. Release behavior of the entrapped molecules changed considerably. This study demonstrated the importance of aqueous-core composition, and gave new insights for possible adjusting of microcapsules physicochemical properties by modulating core-shell interactions. Copyright © 2016 Elsevier Inc. All rights reserved.

APPR-1 RESEARCH AND DEVELOPMENT PROGRAM DECONTAMINATION PROGRAM. TASK II. VOLUME II. EVALUATION OF CHEMICAL AGENTS FOR NUCLEAR REACTOR DECONTAMINATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zegger, J.L.; Pancer, G.P.

1959-02-15

The caustic permanganante-rinse decontamination studies were performed to determine optimum operating conditions as well as the metallurgical effects of the treatment. A treatment with 10% NaOH and 5% potassium by a rinse with a 5% ammorium citrate, 2% citric acid and 1/2% Versene solution was chosen for the decontamination of a stainless steel steam generator, Decontamination factors of greater than 50 were obtained in loop tests using the above treatment. Corrosion and metallurgical results indicated a total penetration of less than 0.01 mil on annealed type 304 stainless steel with no evidence of any deleterious effects. (auth)

Measurement and Modeling of Setschenow Constants for Selected Hydrophilic Compounds in NaCl and CaCl2 Simulated Carbon Storage Brines.

PubMed

Burant, Aniela; Lowry, Gregory V; Karamalidis, Athanasios K

2017-06-20

Carbon capture, utilization, and storage (CCUS), a climate change mitigation strategy, along with unconventional oil and gas extraction, generates enormous volumes of produced water containing high salt concentrations and a litany of organic compounds. Understanding the aqueous solubility of organic compounds related to these operations is important for water treatment and reuse alternatives, as well as risk assessment purposes. The well-established Setschenow equation can be used to determine the effect of salts on aqueous solubility. However, there is a lack of reported Setschenow constants, especially for polar organic compounds. In this study, the Setschenow constants for selected hydrophilic organic compounds were experimentally determined, and linear free energy models for predicting the Setschenow constant of organic chemicals in concentrated brines were developed. Solid phase microextraction was employed to measure the salting-out behavior of six selected hydrophilic compounds up to 5 M NaCl and 2 M CaCl 2 and in Na-Ca-Cl brines. All compounds, which include phenol, p-cresol, hydroquinone, pyrrole, hexanoic acid, and 9-hydroxyfluorene, exhibited log-linear behavior up to these concentrations, meaning Setschenow constants previously measured at low salt concentrations can be extrapolated up to high salt concentrations for hydrophilic compounds. Setschenow constants measured in NaCl and CaCl 2 brines are additive for the compounds measured here; meaning Setschenow constants measured in single salt solutions can be used in multiple salt solutions. The hydrophilic compounds in this study were selected to elucidate differences in salting-out behavior based on their chemical structure. Using data from this study, as well as literature data, linear free energy relationships (LFERs) for prediction of NaCl, CaCl 2 , LiCl, and NaBr Setschenow constants were developed and validated. Two LFERs were improved. One LFER uses the Abraham solvation parameters, which include the index of refraction of the organic compound, organic compound's polarizability, hydrogen bonding acidity and basicity of the organic compound, and the molar volume of the compound. The other uses an octanol-water partitioning coefficient to predict NaCl Setschenow constants. Improved models from this study now include organic compounds that are structurally and chemically more diverse than the previous models. The CaCl 2 , LiCl, and NaBr single parameter LFERs use concepts from the Hofmeister series to predict new, respective Setschenow constants from NaCl Setschenow constants. The Setschenow constants determined here, as well as the LFERs developed, can be incorporated into CCUS reactive transport models to predict aqueous solubility and partitioning coefficients of organic compounds. This work also has implications for beneficial reuse of water from CCUS; this can aide in determining treatment technologies for produced waters.

Assessing hydrodynamic effects on jarosite dissolution rates, reaction products, and preservation on Mars

NASA Astrophysics Data System (ADS)

Dixon, Emily M.; Elwood Madden, Andrew S.; Hausrath, Elisabeth M.; Elwood Madden, Megan E.

2015-04-01

Jarosite flow-through dissolution experiments were conducted in ultrapure water (UPW), pH 2 sulfuric acid, and saturated NaCl and CaCl2 brines at 295-298 K to investigate how hydrologic variables may affect jarosite preservation and reaction products on Mars. K+-based dissolution rates in flowing UPW did not vary significantly with flow rate, indicating that mineral surface reactions control dissolution rates over the range of flow rates investigated. In all of the solutions tested, hydrologic variables do not significantly affect extent of jarosite alteration; therefore, jarosite is equally likely to be preserved in flowing or stagnant waters on Mars. However, increasing flow rate did affect the mineralogy and accumulation of secondary reaction products. Iron release rates in dilute solutions increased as the flow rate increased, likely due to nanoscale iron (hydr)oxide transport in flowing water. Anhydrite formed in CaCl2 brine flow-through experiments despite low temperatures, while metastable gypsum and bassanite were observed in batch experiments. Therefore, observations of the hydration state of calcium sulfate minerals on Mars may provide clues to unravel past salinity and hydrologic conditions as well as temperatures and vapor pressures.

Ion exchange treatment of rinse water generated in the galvanizing process.

PubMed

Marañón, Elena; Fernández, Yolanda; Castrillón, Leonor

2005-01-01

A study was conducted of the viability of using the cationic exchange resins Amberlite IR-120 and Lewatit SP-112 to treat rinse water generated in the galvanizing process as well as acidic wastewater containing zinc (Zn) and iron (Fe). Solutions containing either 100 mg/L of Zn at pH 5.6 (rinse water) or Fe and Zn at concentrations of 320 and 200 mg/L at pH 1.5 (acidic water), respectively, were percolated through packed beds until the resins were exhausted. Breakthrough capacities obtained ranged between 1.1 and 1.5 meq metal/mL resin. The elution of metal and the regeneration of resins were performed with hydrochloric acid. The influence of the flowrate used during the loading stage was also studied, with 0.5 bed volumes/min (3.2 cm/min) found to be the optimum flowrate.

Transport and retention of biochar nanoparticles in a paddy soil under environmentally-relevant solution chemistry conditions.

PubMed

Chen, Ming; Wang, Dengjun; Yang, Fan; Xu, Xiaoyun; Xu, Nan; Cao, Xinde

2017-11-01

Land application of biochar has been increasingly recommended as a powerful strategy for carbon sequestration and soil remediation. However, the biochar particles, especially those in the nanoscale range, may migrate or carry the inherent contaminants along the soil profile, posing a potential risk to the groundwater. This study investigated the transport and retention of wood chip-derived biochar nanoparticles (NPs) in water-saturated columns packed with a paddy soil. The environmentally-relevant soil solution chemistry including ionic strength (0.10-50 mM), electrolyte type (NaCl and CaCl 2 ), and natural organic matter (0-10 mg L -1 humic acid) were tested to elucidate their effects on the biochar NPs transport. Higher mobility of biochar NPs was observed in the soil at lower ionic strengths, with CaCl 2 electrolyte being more effective than NaCl in decreasing biochar NPs transport. The retained biochar NPs in NaCl was re-entrained (∼57.7%) upon lowering transient pore-water ionic strength, indicating that biochar NPs were reversibly retained in the secondary minimum. In contrast, negligible re-entrainment of biochar NPs occurred in CaCl 2 due to the primary minimum and/or particle aggregation. Humic acid increased the mobility of biochar NPs, likely due to enhanced electrosteric repulsive interactions. The transport behaviors of biochar NPs can be well interpreted by a two-site kinetic retention model that assumes reversible retention for one site, and irreversible retention for the other site. Our findings indicated that the transport of wood chip biochar NPs is significant in the paddy soil, highlighting the importance of understanding the mobility of biochar NPs in natural soils for accurately assessing their environmental impacts. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Adding calcium salts and sulphur dioxide for preserving firmness and colour of frozen cauliflower (author's transl)].

PubMed

Polesello, A; Pizzocaro, F

1975-01-01

The results of trials aimed to keep colour and firmness of frozen cauliflower during storage, by pretreatments based on Calcium salts and SO2 impregnation are referred here. Among the different procedures tested, that of introducing under vacuum gaseous SO2 at low pressure, followed by soaking in CaCl2 0,1 N solution has shown the best efficaceousness.

Zeolite-based hemostat QuikClot releases calcium into blood and promotes blood coagulation in vitro

PubMed Central

Li, Jing; Cao, Wei; Lv, Xiao-xing; Jiang, Li; Li, Yue-jun; Li, Wang-zhou; Chen, Shao-zong; Li, Xue-yong

2013-01-01

Aim: To examine the changes in electrolyte concentrations after addition of zeolite-based hemostat QuikClot in blood and the effects of zeolite on blood coagulation in vitro. Methods: Fresh blood was taken from healthy adult volunteers and sheep, and the electrolyte concentrations in blood were measured using a blood electrolyte analyzer. Zeolite Saline Solution (ZSS) was prepared by addition of 2 g zeolite to 0.9% NaCl solution (4, 8, or 16 mL). The electrolytes in ZSS were measured using inductively coupled plasma atomic emission spectroscopy. The prothrombin time (PT) and activated partial thromboplastin time (APTT) of blood were measured using the test tube method. The activated clotting time (ACT) and clotting rate (CR) of blood were measured with Sonoclot Coagulation and Platelet Function Analyzer. Results: Addition of zeolite (50 and 100 mg) in 2 mL human blood significantly increased Ca2+ concentration, while Na+ and K+ concentrations were significantly decreased. Addition of zeolite (50 and 100 mg) in 0.9% NaCl solution (2 mL) caused similar changes in Ca2+ and Na+ concentrations. Si4+ (0.2434 g/L) and Al3+ (0.2575 g/L) were detected in ZSS (2 g/8 mL). Addition of ZSS in sheep blood shortened APTT in a concentration dependent manner, without changing PT. ZSS or aqueous solution of CaCl2 that contained Ca2+ concentration identical to that of ZSS significantly shortened ACT in human blood without significantly changing CR, and the effect of ZSS on ACT was not significantly different from that of CaCl2. Conclusion: Zeolite releases Ca2+ into blood, thus accelerating the intrinsic pathway of blood coagulation and shortening the clot formation time. PMID:23334236

Zeolite-based hemostat QuikClot releases calcium into blood and promotes blood coagulation in vitro.

PubMed

Li, Jing; Cao, Wei; Lv, Xiao-xing; Jiang, Li; Li, Yue-jun; Li, Wang-zhou; Chen, Shao-zong; Li, Xue-yong

2013-03-01

To examine the changes in electrolyte concentrations after addition of zeolite-based hemostat QuikClot in blood and the effects of zeolite on blood coagulation in vitro. Fresh blood was taken from healthy adult volunteers and sheep, and the electrolyte concentrations in blood were measured using a blood electrolyte analyzer. Zeolite Saline Solution (ZSS) was prepared by addition of 2 g zeolite to 0.9% NaCl solution (4, 8, or 16 mL). The electrolytes in ZSS were measured using inductively coupled plasma atomic emission spectroscopy. The prothrombin time (PT) and activated partial thromboplastin time (APTT) of blood were measured using the test tube method. The activated clotting time (ACT) and clotting rate (CR) of blood were measured with Sonoclot Coagulation and Platelet Function Analyzer. Addition of zeolite (50 and 100 mg) in 2 mL human blood significantly increased Ca(2+) concentration, while Na(+) and K(+) concentrations were significantly decreased. Addition of zeolite (50 and 100 mg) in 0.9% NaCl solution (2 mL) caused similar changes in Ca(2+) and Na(+) concentrations. Si(4+) (0.2434 g/L) and Al(3+) (0.2575 g/L) were detected in ZSS (2 g/8 mL). Addition of ZSS in sheep blood shortened APTT in a concentration dependent manner, without changing PT. ZSS or aqueous solution of CaCl2 that contained Ca(2+) concentration identical to that of ZSS significantly shortened ACT in human blood without significantly changing CR, and the effect of ZSS on ACT was not significantly different from that of CaCl2. Zeolite releases Ca(2+) into blood, thus accelerating the intrinsic pathway of blood coagulation and shortening the clot formation time.

[The Influence of Different Ionic Concentration in Cell Physiological Solution on Temperature Measurement by Near Infrared].

PubMed

Zheng, Yu; Chen, Xiong; Zhou, Mei; Wang, Meng-jun; Wang, Jin-hai; Li, Gang; Cui, Jun

2015-10-01

It is important to real-timely monitor and control the temperature of cell physiological solution in patch clamp experiments, which can eliminate the uncertainty due to temperature and improve the measurement accuracy. This paper studies the influence of different ions at different concentrations in the physiological solution on precision of a temperature model by using near infrared spectroscopy and chemometrics method. Firstly, we prepared twelve sample solutions respectively with the solutes of CaCl2, KCl and NaCl at four kinds of concentrations, and collected the spectra of different solutions at the setting temperature range 20-40 degrees C, the range of the spectra is 9 615-5 714 cm(-1). Then we divided the spectra of each solution at different temperatures into two parts (a training set and a prediction set) by three methods. Interval partial least squares method was used to select an effective wavelength range and develop calibration models between the spectra in the selected range and temperature velues. The experimental results show that RMSEP of CaCl2 solution with 0.25 g x mL(-1) is maximum, the result of the three tests are 0.386 3, 0.303 7 and 0.337 2 degrees C, RMSEP of NaCl with 0.005 g x mL(-1) solution is minimum, the result of the three tests are 0.220 8, 0.155 3 and 0.145 2 degrees C. The experimental results indicate that Ca2+ has the greatest influence on the accuracy of the temperature model of the cell physiological solution, then K+, and Na+ has the least influence. And with the ionic concentration increasing, the model accuracy decreases. Therefore; when we build the temperature model of cell physiological solution, it is necessary to change the proportion of the three kinds of main ions in cell physiological solution reasonably in order to correct the effects of different ionic concentrations in physiological solution and improve the accuracy of temperature measurements by near infrared spectroscopy.

The use of a rotating cylinder electrode to recover zinc from rinse water generated by the electroplating industry.

PubMed

Matlalcuatzi, Sairi; Nava, José L

2012-01-01

This work concerns the application of a laboratory scale rotating cylinder electrode (RCE) to recover zinc from rinse water generated by the electrolytic zinc process (initially 1,300, 4,400, 50, 20 mg L(-1) of Zn(II), Fe(III), Ag(I) and Cr(VI), respectively, at pH 2), although it is also applicable to other electroplating industries. Experimental results demonstrated the convenience of the removal of ferric ions, as (Fe(OH)(3(s))) by a pH adjustment to 4, before zinc electro recovery on the RCE. The generation of smooth zinc deposits on the RCE was obtained at Reynolds numbers within the range of 15,000 ≤ Re ≤ 124,000 and limiting current densities (J(L)) in the interval of -4.8 to -13 mA cm(-2). The zinc recovery reached a conversion of 67% in 90 min of electrolysis for Re = 124,000 and J = -13 mA cm(-2), 21% current efficiency, and energy consumption of 9.5 kWh m(-3). The treated solution can be recycled back through the same rinsing process.

Osteogenic differentiation of equine adipose tissue derived mesenchymal stem cells using CaCl2.

PubMed

Elashry, Mohamed I; Baulig, Nadine; Heimann, Manuela; Bernhardt, Caroline; Wenisch, Sabine; Arnhold, Stefan

2018-04-01

Adipose tissue derived mesenchymal stem cells (ASCs) may be used to cure bone defects after osteogenic differentiation. In this study we tried to optimize osteogenic differentiation for equine ASCs using various concentrations of CaCl 2 in comparison to the standard osteogenic protocol. ASCs were isolated from subcutaneous adipose tissue from mixed breed horses. The osteogenic induction protocols were (1) the standard osteogenic medium (OM) composed of dexamethasone, ascorbic acid and β-glycerol phosphate; (2) CaCl 2 based protocol composed of 3, 5 and 7.5mM CaCl 2 . Differentiation and proliferation were evaluated at 7, 10, 14 and 21days post-differentiation induction using the alizarin red staining (ARS) detecting matrix calcification. Semi-quantification of cell protein content, ARS and alkaline phosphatase activity (ALP) were performed using an ELISA reader. Quantification of the transcription level for the common osteogenic markers alkaline phosphatase (ALP) and Osteopontin (OP) was performed using RT-qPCR. In the presence of CaCl 2 , a concentration dependent effect on the osteogenic differentiation capacity was evident by the ARS evaluation and OP gene expression. We provide evidence that 5 and 7mM CaCl 2 enhance the osteogenic differentiation compared to the OM protocol. Although, there was a clear commitment of ASCs to the osteogenic fate in the presence of 5 and 7mM CaCl 2 , cell proliferation was increased compared to OM. We report that an optimized CaCl 2 protocol reliably influences ASCs osteogenesis while conserving the proliferation capacity. Thus, using these protocols provide a platform for using ASCs as a cell source in bone tissue engineering. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combination of three-stage sink-float method and selective flotation technique for separation of mixed post-consumer plastic waste.

PubMed

Pongstabodee, Sangobtip; Kunachitpimol, Napatr; Damronglerd, Somsak

2008-01-01

The aim of this research was to separate the different plastics of a mixed post-consumer plastic waste by the combination of a three-stage sink-float method and selective flotation. By using the three-stage sink-float method, six mixed-plastic wastes, belonging to the 0.3-0.5 cm size class and including high density polyethylene (HDPE), polypropylene (PP), polyvinylchloride (PVC), polystyrene (PS), polyethylene terephthalate (PET) and acrylonitrile-butadiene-styrene copolymers (ABS) were separated into two groups, i.e., a low density plastic group (HDPE and PP) and a high density plastic group (PET, PVC, PS and ABS) by tap water. Plastic whose density is less than that of the medium solution floats to the surface, while the one whose density is greater than that of the medium solution sinks to the bottom. The experimental results elucidated that complete separation of HDPE from PP was achieved by the three-stage sink-float method with 50% v/v ethyl alcohol. To succeed in the separation of a PS/ABS mixture from a PET/PVC mixture by the three-stage sink-float method, a 30% w/v calcium chloride solution was employed. To further separate post-consumer PET/PVC and PS/ABS based on plastic type, selective flotation was carried out. In order to succeed in selective flotation separation, it is necessary to render hydrophilic the surface of one or more species while the others are kept in a hydrophobic state. In flotation studies, the effects of wetting agent, frother, pH of solution and electrolyte on separation were determined. The selective flotation results showed that when using 500 mg l(-1) calcium lignosulfonate, 0.01 ppm MIBC, and 0.1 mg l(-1) CaCl2 at pH 11, PET could be separated from PVC. To separate ABS from PS, 200 mg l(-1) calcium lignosulfonate and 0.1 mg l(-1) CaCl2 at pH 7 were used as a flotation solution. Wettability of plastic increases when adding CaCl2 and corresponds to a decrease in its contact angles and to a reduction in the recovery of plastic in the floated product.

Sorption and desorption of carbamazepine, naproxen and triclosan in a soil irrigated with raw wastewater: estimation of the sorption parameters by considering the initial mass of the compounds in the soil.

PubMed

Durán-Álvarez, Juan C; Prado-Pano, Blanca; Jiménez-Cisneros, Blanca

2012-06-01

In conventional sorption studies, the prior presence of contaminants in the soil is not considered when estimating the sorption parameters because this is only a transient state. However, this parameter should be considered in order to avoid the under/overestimation of the soil sorption capacity. In this study, the sorption of naproxen, carbamazepine and triclosan was determined in a wastewater irrigated soil, considering the initial mass of the compounds. Batch sorption-desorption tests were carried out at two soil depths (0-10 cm and 30-40 cm), using either 10 mM CaCl(2) solution or untreated wastewater as the liquid phase. Data were satisfactorily fitted to the initial mass model. For the two soils, release of naproxen and carbamazepine was observed when the CaCl(2) solution was used, but not in the soil/wastewater system. The compounds' release was higher in the topsoil than in the 30-40 cm soil. Sorption coefficients (K(d)) for CaCl(2) solution tests showed that in the topsoil, triclosan (64.9 L kg(-1)) is sorbed to a higher extent than carbamazepine and naproxen (5.81 and 2.39 L kg(-1), respectively). In the 30-40 cm soil, carbamazepine and naproxen K(d) values (11.4 and 4.41 L kg(-1), respectively) were higher than those obtained for the topsoil, while the triclosan K(d) value was significantly lower than in the topsoil (19.2 L kg(-1)). Differences in K(d) values were found when comparing the results obtained for the two liquid phases. Sorption of naproxen and carbamazepine was reversible for both soils, while sorption of triclosan was found to be irreversible. This study shows the sorption behavior of three pharmaceuticals in a wastewater irrigated soil, as well as the importance of considering the initial mass of target pollutants in the estimation of their sorption parameters. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of washing produce contaminated with the snail and slug hosts of Angiostrongylus cantonensis with three common household solutions.

PubMed

Yeung, Norine W; Hayes, Kenneth A; Cowie, Robert H

2013-06-01

The emerging infectious disease angiostrongyliasis (rat lungworm disease) is caused by ingesting snails and slugs infected by the nematode Angiostrongylus cantonensis. The definitive hosts of A. cantonensis are rats and the obligatory intermediate hosts are slugs and snails. Many cases result from accidentally ingesting infected snails or slugs on produce (eg, lettuce). This study assessed three readily available household products as washing solutions for removing snails and slugs from produce (romaine lettuce) to lower the probability of accidentally ingesting them. The solutions were acetic acid (vinegar), sodium hypochlorite (bleach), and sodium chloride (domestic salt). Snail and slug species known to be intermediate hosts and that are common in the Hawaiian Islands were used in the experiments: the alien snail Succinea tenella, the alien semi-slug Parmarion martensi, and the alien slugs Veronicella cubensis and Deroceras laeve. None of the products was any more effective than washing and rinsing with tap water alone. Most snails and slugs were removed after treatment but some remained on the lettuce even after washing and rinsing the produce. Only washing, rinsing, and then rinsing each leaf individually resulted in complete removal of all snails and slugs. The study did not address removal of any remaining slime left by the snails and slugs, nor did it address killing of worms.

Activation of free sperm and dissociation of sperm bundles (spermatozeugmata) of an endangered viviparous fish, Xenotoca eiseni.

PubMed

Liu, Yue; Yang, Huiping; Torres, Leticia; Tiersch, Terrence R

2018-04-01

Knowledge of sperm motility activation for viviparous fishes has been limited to study of several species in Poeciliidae, and the dissociation of sperm bundles is even less understood. The goal of this study was to use the endangered Redtail Splitfin (Xenotoca eiseni) as a model to investigate the activation of sperm from viviparous fishes by study of free sperm and spermatozeugmata (unencapsulated sperm bundles). The specific objectives were to evaluate the effects of: (1) osmotic pressure and refrigerated storage (4 °C) on activation of free sperm, (2) osmotic pressure, ions, and pH on dissociation of spermatozeugmata, and (3) CaCl 2 concentration and pH on sperm membrane integrity. Free sperm were activated in Ca 2+ -free Hanks' balanced salt solution at 81-516 mOsmol/kg. The highest motility (19 ± 6%) was at 305 mOsmol/kg and swim remained for 84 h. Glucose (300-700 mOsmol/kg), NaCl (50-600 mOsmol/kg), and KCl, MgCl 2 , and MnCl 2 at 5-160 mM activated sperm within spermatozeugmata, but did not dissociate spermatozeugmata. CaCl 2 at 5-160 mM dissociated spermatozeugmata within 10 min. Solutions of NaCl-NaOH at pH 11.6 to 12.4 dissociated spermatozeugmata within 1 min. The percentage of viable cells had no significant differences (P = 0.2033) among different concentrations of CaCl 2 , but it was lower (P < 0.0001) at pH 12.5 than at pH between 7.0 and 12.0. Overall, this study provided a foundation for quality evaluation of sperm and spermatozeugmata from livebearing fishes, and for development of germplasm repositories for imperiled goodeids. Copyright © 2018 Elsevier Inc. All rights reserved.

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Code of Federal Regulations, 2014 CFR

2014-07-01

... square foot) is washed for 1 minute. Wipe smooth surfaces with a cleaning solution-soaked disposable absorbent pad such that each 900 cm2 (1 square foot) is wiped for 1 minute. Wash any surface square foot... solution with 1 gallon of clean water per square foot and capture the rinse water. Mop up the wet surface...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Code of Federal Regulations, 2012 CFR

2012-07-01

... square foot) is washed for 1 minute. Wipe smooth surfaces with a cleaning solution-soaked disposable absorbent pad such that each 900 cm2 (1 square foot) is wiped for 1 minute. Wash any surface square foot... solution with 1 gallon of clean water per square foot and capture the rinse water. Mop up the wet surface...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Code of Federal Regulations, 2013 CFR

2013-07-01

... square foot) is washed for 1 minute. Wipe smooth surfaces with a cleaning solution-soaked disposable absorbent pad such that each 900 cm2 (1 square foot) is wiped for 1 minute. Wash any surface square foot... solution with 1 gallon of clean water per square foot and capture the rinse water. Mop up the wet surface...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Code of Federal Regulations, 2010 CFR

2010-07-01

... square foot) is washed for 1 minute. Wipe smooth surfaces with a cleaning solution-soaked disposable absorbent pad such that each 900 cm2 (1 square foot) is wiped for 1 minute. Wash any surface square foot... solution with 1 gallon of clean water per square foot and capture the rinse water. Mop up the wet surface...

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Code of Federal Regulations, 2011 CFR

2011-07-01

... square foot) is washed for 1 minute. Wipe smooth surfaces with a cleaning solution-soaked disposable absorbent pad such that each 900 cm2 (1 square foot) is wiped for 1 minute. Wash any surface square foot... solution with 1 gallon of clean water per square foot and capture the rinse water. Mop up the wet surface...

Decontaminating materials used in ground water sampling devices: Organic contaminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, L.V.; Ranney, T.A.

2000-12-31

In these studies, the efficiency of various decontamination protocols was tested on small pieces of materials commonly used in ground water sampling devices. Three materials, which ranged in ability to sorb organic solutes, were tested: stainless steel (SS), rigid polyvinyl chloride (PVC), and polytetrafluoroethylene (PTFE). The test pieces were exposed to two aqueous test solutions: One contained three volatile organic compounds (VOCs) and one nitroaromatic compound, and the other contained four pesticides. Also, three types of polymetic tubing were exposed to pesticide solutions. Generally, the contact times were 10 minutes and 24 hours for sorption and desorption. The contaminants weremore » removed from the nonpermeable SS and the less-sorptive rigid PVC test pieces simply by washing with a hot detergent solution and rinsing with hot water. Additional treatment was required for the PTFE test pieces exposed to the VOCs and for the low-density polyethylene (LDPE) tubing exposed to the pesticide test solution. Solvent rinsing did not improve removal of the three VOCs form the PTFE and only marginally improved removal of the residual pesticides from the LDPE. However, a hot water and detergent wash and rinse followed by oven drying at approximately 105 C was effective for removing the VOCs from the PTFE and substantially reduced pesticide contamination from the LDPE.« less

Bonding-Compatible Corrosion Inhibitor for Rinsing Metals

NASA Technical Reports Server (NTRS)

Saunders, C. R.; Wurth, L. A.; Radar, A.

2005-01-01

A corrosion-inhibiting mixture of compounds has been developed for addition to the water used to rinse metal parts that have been cleaned with aqueous solutions in preparation for adhesive bonding of the metals to rubber and rubber-like materials. Prior to the development of this corrosion inhibitor, the parts (made, variously, of D6AC steel and 7075-T73 aluminum) were rinsed by deionized water, which caused corrosion in some places on the steel parts especially in such occluded places as sealing surfaces and threaded blind holes. An integral part of the particular cleaning process is the deposition of a thin layer of silicates and silane primers that increase the strength of the adhesive bond. The corrosion inhibitor is formulated, not only to inhibit corrosion of both D6AC steel and 7075- T73 aluminum, but also to either increase or at least not reduce the strength of the adhesive bond to be formed subsequently. The corrosion inhibitor is a mixture of sodium silicate and sodium tetraborate. The sodium silicate functions as both a corrosion inhibitor and a bond-strength promoter in association with the silane primers. The sodium tetraborate buffers the rinse solution at the optimum pH and functions as a secondary corrosion inhibitor for the steel. For a given application, the concentrations of sodium silicate and sodium tetraborate must be chosen in a compromise among the needs to inhibit corrosion of steel, inhibit corrosion of aluminum, and minimize cosmetic staining of both steel and aluminum. Concentrations of sodium silicate in excess of 150 parts of silicon per million parts of solution (ppm Si) have been determined to enhance inhibition of corrosion; unfortunately, because of the alkalinity of sodium silicate, even a small concentration can raise the pH of the rinse solution to such a level that aluminum becomes corroded despite the inhibiting effect. The pH of a solution that contains a high concentration of sodium silicate can be decreased by adding sodium tetraborate. On the other hand, the addition of sodium tetraborate increases the concentration of dissolved solids to such a high level that cosmetic staining becomes an issue.

Sequential application of NaHCO3, CaCl2 and Candida oleophila (isolate 13L) affects significantly Penicillum expansum growth and the infection degree in apples.

PubMed

Molinu, M G; Pani, G; Venditti, T; Dore, A; Ladu, G; D'Hallewin, G

2011-01-01

The employment of biocontrol agents to restrain postharvest pathogens is an encouraging approach, although, efficacy and consistency are still below those of synthetic pesticides. Up to date, the 'integrated control strategy' seems to be the most promising way to overcome this gap. Here, we report the feasibility to control postharvest decay caused by Penicillium expansum in apples by a 2 min, single or sequential, immersion in water with an antagonistic yeast (Candida oleophila, isolate '13L'), 2% NaHCO3 (SBC) or 1% CaCl2. The treatments were carried out, on appels cv 'Miali' either un-wounded, wounded or wound-pathogen inoculated and then stored at 2 degrees C for 30 d followed by a 6 d simulated marketing period at 20 degrees C or alternatively stored only for 7 d at 20 degrees C. As a general role, the best results were attained when CaCl2 was applied with the yeast or when preceded by the SBC treatment. When the wounding and inoculation took place 24 h before the treatment, the latter application sequence of the two salts was three times more effective compared to the treatment with the sole antagonist, and one time when performed 24 h after the treatment. Interestingly, apples immersed in the sole 2% SBC solution had the highest percentage of decay during storage and when inoculated before moving to the simulated marketing period at 20 degrees C.

Comparison of sodium hydroxide and calcium hydroxide pretreatments on the enzymatic hydrolysis and lignin recovery of sugarcane bagasse.

PubMed

Chang, Menglei; Li, Denian; Wang, Wen; Chen, Dongchu; Zhang, Yuyuan; Hu, Huawen; Ye, Xiufang

2017-11-01

Sodium hydroxide (NaOH) and calcium hydroxide (Ca(OH) 2 ) respectively dissolved in water and 70% glycerol were applied to treat sugarcane bagasse (SCB) under the condition of 80°C for 2h. NaOH solutions could remove more lignin and obtain higher enzymatic hydrolysis efficiency of SCB than Ca(OH) 2 solutions. Compared with the alkali-water solutions, the enzymatic hydrolysis of SCB treated in NaOH-glycerol solution decreased, while that in Ca(OH) 2 -glycerol solution increased. The lignin in NaOH-water pretreatment liquor could be easily recovered by calcium chloride (CaCl 2 ) at room temperature, but that in Ca(OH) 2 -water pretreatment liquor couldn't. NaOH pretreatment is more suitable for facilitating enzymatic hydrolysis and lignin recovery of SCB than Ca(OH) 2 pretreatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Iodine

MedlinePlus

... the uterus (endometritis). Washing the vagina with a solution containing iodine in the form of povidone-iodine ... infection (periodontitis). Research suggests that rinsing with a solution containing iodine in the form of povidone-iodine ...

[Effects of calcium and ABA on photosynthesis and related enzymes activities in cucumber seedlings under drought stress].

PubMed

Chen, Lu Lu; Wang, Xiu Feng; Liu, Mei; Yang, Feng Juan; Shi, Qing Hua; Wei, Min; Li, Qing Ming

2016-12-01

To investigate the effect of calcium and ABA on photosynthesis and the activities of antioxidant enzymes in cucumber seedlings under drought stress, the cucumber was used as the expe-riment materials, normal nutrient solution culture was considered as the control, and PEG-6000 application in the nutrient solution simulated the drought stress. There were five different treatments which were spraying water, ABA, CaCl 2 +ABA, LaCl 3 (calcium channel inhibitor)+ABA and EGTA (calcium ion chelating agent)+ABA under drought stress. The results showed that drought stress inhibited the growth of cucumber seedlings, and reduced the activities of antioxidant enzymes, nitrate reductase, net photosynthetic rate and fluorescence parameters of the cucumber seedlings leaves. The application of ABA reduced the inhibition of activities of superoxide dismutase (SOD), peroxidase (POD), catalase (CAT) and ascorbate peroxidase (APX), photosynthesis (P n , g s ) and the fluorescence parameters (F v '/F m ', q P and ETR), and decreased the damage of drought stress on plant. Spraying CaCl 2 +ABAsignificantly promoted the positive effect of ABA, while EGTA+ABA and LaCl 3 +ABA didn't show the promoting effect.

3D Bioprinting of Highly Thixotropic Alginate/Methylcellulose Hydrogel with Strong Interface Bonding.

PubMed

Li, Huijun; Tan, Yu Jun; Leong, Kah Fai; Li, Lin

2017-06-14

A robust alginate/methylcellulose (Alg/MC) blend hydrogel, with a strategy to improve adhesion between printed layers, has been fabricated for the first time for three-dimensional (3D) bioprinting. The optimized Alg/MC blend hydrogel exhibits a highly thixotropic property, great extrudability, and stackability. With treatment by a trisodium citrate (TSC) solution, the interfacial bonding between the printed layers is significantly improved. The TSC solution acts as a chelating agent to remove the superficial calcium ions at each layer. Post-cross-linking in a CaCl 2 bath after 3D printing further enhances the adhesion strength between the layers. The key parameters affecting the interfacial strength of the Alg/MC hydrogel are found to be the concentration of TSC, the volume of TSC, and the concentration of CaCl 2 in the bath. The Alg/MC hydrogel with the aid of TSC demonstrates superior printability, high stackability (150 layers can be printed), and high shape fidelity. A good cell viability of >95% is obtained for a freshly 3D-bioprinted Alg/MC construct. The novel Alg/MC hydrogel with the aid of TSC has been shown to have a great potential as an advanced 3D bioprinting material.

Efficacy of mouth rinses and toothpaste on tooth whitening.

PubMed

Torres, C R G; Perote, L C C C; Gutierrez, N C; Pucci, C R; Borges, A B

2013-01-01

People increasingly desire tooth whitening. Considering the wide range of whitening products on the market, this study evaluated the efficacy of whitening toothpastes and mouth rinses compared with the 10% carbamide peroxide (CP) whitening gel. We obtained 120 cylindrical specimens from bovine teeth, which were darkened for 24 hours in a coffee solution. The color measurement was performed by a spectrophotometer using the CIE L*a*b* system, and specimens were divided into six groups according to the use of the following agents: group 1, conventional fluoridated toothpaste; group 2, Close Up White Now; group 3, Listerine Whitening; group 4, Colgate Plax Whitening; group 5, experimental mouth rinse with Plasdone; and group 6, 10% CP Whiteness Perfect. After the simulation of 12 weeks of treatment for groups 1 to 5 and 14 days of treatment for group 6, the specimens were subjected to a new color reading. Data were subjected to one-way analysis of variance (α=0.05), which showed significant differences among groups after 12 weeks for ΔE (p=0.001). Results of the Tukey test revealed that groups 3, 4, and 6 presented significantly higher color alteration than groups 1, 2, and 5. The whitening toothpaste Close Up White Now and the experimental mouth rinse with Plasdone showed similar color alteration as conventional toothpaste after a 12-week treatment simulation. These groups presented significantly lower color alteration compared with whitening mouth rinses Listerine and Colgate Plax Whitening, which showed similar results to those observed after 14 days of bleaching with 10% CP treatment.

The impact of electrolyte on the adsorption of the anionic surfactant methyl ester sulfonate at the air-solution interface: Surface multilayer formation.

PubMed

Xu, H; Thomas, R K; Penfold, J; Li, P X; Ma, K; Welbourne, R J L; Roberts, D W; Petkov, J T

2018-02-15

The methyl ester sulfonates represent a promising group of anionic surfactants which have the potential for improved performance and biocompatibility in a range of applications. Their solution properties, in particular their tolerance to hard water, suggests that surface ordering may occur in the presence of multi-valent counterion. Understanding their adsorption properties in a range of different circumstances is key to the exploitation of their potential. Neutron reflectivity and surface tension have been used to characterise the adsorption at the air-aqueous solution interface of the anionic surfactant sodium tetradecanoic 2-sulfo 1-methyl ester, C 14 MES, in the absence of electrolyte and in the presence of mono, di, and tri-valent counterions, Na + , Ca 2+ , and Al 3+ . In particular the emphasis has been on exploring the tendency to form layered structures at the interface. In the absence of electrolyte and in the presence of NaCl and CaCl 2 and AlCl 3 at low concentrations monolayer adsorption is observed, and the addition of electrolyte results in enhanced adsorption. In the presence of NaCl and CaCl 2 only monolayer adsorption is observed. However at higher AlCl 3 concentrations surface multilayer formation is observed, in which the number of bilayers at the surface depends upon the surfactant and AlCl 3 concentrations. Copyright © 2017 Elsevier Inc. All rights reserved.

Removal of nickel from electroplating rinse waters using electrostatic shielding electrodialysis/electrodeionization.

PubMed

Dermentzis, Konstantinos

2010-01-15

Electrostatic shielding zones made of electrode graphite powder were used as a new type of ionic and electronic current sinks. Because of the local elimination of the applied electric field, voltage and current within the zones, ions are led inside them and accumulate there. The current sinks were implemented in electrostatic shielding electrodialysis of a simulated nickel plating rinse water containing 100 mg L(-1) nickel and electrodeionization of a 0.001 M NiSO(4) solution with simultaneous electrochemical regeneration of the ion exchange resin beds. Pure water was obtained with a Ni(2+) ion concentration of less than 0.1 mg L(-1) at a flow rate of 2.02 x 10(-4)dm(3)s(-1) diluate stream and a current density of 30 Am(-2).

The AN69 ST haemodialysis membrane under conditions of two different extracorporeal circuit rinse protocols a comparison of thrombogenicity parameters.

PubMed

Richtrova, Pavlina; Opatrny, Karel; Vit, Ladislav; Sefrna, Frantisek; Perlik, Radek

2007-10-01

Thrombogenicity is an important parameter of haemodialysis (HD) membrane biocompatibility. The surface of the polyacrylonitrile AN69 ST membrane is coated with a polyethylenimine. This modification allows heparin adsorption. The binding of heparin to the membrane surface occurs during priming of the extracorporeal circuit (ECC) by rinsing it with saline and heparin. Our aims were to assess and compare the thrombogenicity of the AN69 ST membrane under conditions of two extracorporeal circuit (ECC) rinse protocols-with and without unfractionated heparin (UFH). In a prospective, crossover and randomized study, we examined 10 patients during HD after ECC preparation with either rinse protocols. Prior to HD and at 15, 60 and 240 min, we determined plasma levels of the thrombin-antithrombin complexes (TAT), platelet factor 4 (PF4), heparin concentration (antiXa) and thrombocyte count. Systemic anticoagulation was performed using UFH. During HD after ECC rinse without UFH, there was a significantly earlier and more marked increase in TAT compared with UFH-containing rinse (P <0.05). Using Spearman coefficient, we demonstrated a significant correlation between TAT and antiXa at 60 min (r = -0.534) and 240 min (r = -0.538). A comparison of the TAT/antiXa ratios between rinses at 60 min revealed a significantly higher increase in TAT following UFH-free rinse (P <0.05). There was no difference in PF4 between the rinses. Platelet count did not change significantly during HD using either rinse protocol. Based on plasma TAT levels, ECC priming with an UFH-containing solution reduces the thrombogenicity of the AN69 ST membrane. There is no significant difference between both types of priming concerning PF4 and thrombocyte count.

Efficacy of detergents in removing Salmonella and Shigella spp. from the surface of fresh produce.

PubMed

Raiden, Renee M; Sumner, Susan S; Eifert, Joseph D; Pierson, Merle D

2003-12-01

Fresh produce has been implicated in several foodborne disease outbreaks. Produce surfaces can be primary sites of contamination during production and handling. One approach to reduce contamination is to treat fresh produce with rinsing agents. In this study, different detergent agents were used at 22 and 40 degrees C to determine their efficacy in removing Salmonella and Shigella spp. from the surfaces of strawberries, tomatoes, and green-leaf lettuce. Produce was inoculated at 22 degrees C with a cocktail of nalidixic acid-resistant organisms (6 to 6.5 log CFU/ml). After air drying for 1 h, samples were rinsed with either 0.1% Tween 80, 0.1% sodium lauryl sulfate (SLS), or water (control) at 22 or 40 degrees C. Rinse solutions were spiral plated onto tryptic soy agar supplemented with 50 mg of nalidixic acid per liter. In trials involving strawberries and lettuce, Salmonella and Shigella were removed at levels of 4 and 3 log CFU/ml, respectively, except from Salmonella-inoculated strawberries rinsed with SLS, for which minimal removal rates were 1.5 log CFU/ml at 22 degrees C and < 1 log CFU/ml at 40 degrees C. When whole strawberries were analyzed after rinsing with SLS, few organisms were recovered. This result suggests that SLS may have a lethal or sublethal effect on Salmonella, especially when a 40 degrees C solution is used. Salmonella and Shigella removal rates for tomatoes were 1 and 1.5 log CFU/ml lower, respectively, than those for strawberries or lettuce. Overall, detergents were no more effective in removing organisms from produce than water was. The detergents examined would not constitute effective overall produce rinse treatments.

Effect of irrigation water salinity on the organic carbon mineralization in soil (laboratory incubation)

NASA Astrophysics Data System (ADS)

Mancer, Halima; Bouhoun, Mustapha Daddi

2018-05-01

In a laboratory study, the impact of salts on mineralization of organic carbon of soil was examined through the monitoring of the amount of CO2-C released from soil. The soil used was classified as a nonsaline soil which has been irrigated with artificially salinized water, a factorial combination of three types of salts (NaCl, MgCl2, CaCl2) with three levels of electrical conductivities (3, 6, and 9 dS.m-1) was used to assess the Carbon mineralization. The incubation was carried out under aerobic conditions and at a constant temperature of 28 °C during 70 days with moisture adjusted to 2/3 of the field capacity. No significant (P > 0.05) variation in the amount of CO2-C release from soil was observed until day 56 of the incubation, but it was significantly different due to the irrigation with salt solutions during the days: 70 (p ≤ 0.05). The results suggest that the rate of C-CO2 evolution decreased with the increase in water salinity compared to the control. Also this decrease of C-mineralization in the soils irrigated by the salts solutions of NaCl was the greatest compared to the other two salts (CaCl2, and MgCl2). These results suggest that C mineralization depended on the type of salts as well as the duration of incubation.

Photosynthesis is improved by exogenous calcium in heat-stressed tobacco plants.

PubMed

Tan, Wei; Meng, Qing wei; Brestic, Marian; Olsovska, Katarina; Yang, Xinghong

2011-11-15

Effects of exogenous calcium chloride (CaCl(2)) (20 mM) on photosynthetic gas exchange, photosystem II photochemistry, and the activities of antioxidant enzymes in tobacco plants under high temperature stress (43°C for 2 h) were investigated. Heat stress resulted in a decrease in net photosynthetic rate (P(n)), stomatal conductance as well as the apparent quantum yield (AQY) and carboxylation efficiency (CE) of photosynthesis. Heat stress also caused a decrease of the maximal photochemical efficiency of primary photochemistry (F(v)/F(m)). On the other hand, CaCl(2) application improved P(n), AQY, and CE as well as F(v)/F(m) under high temperature stress. Heat stress reduced the activities of superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), peroxidase (POD), whereas the activities of these enzymes either decreased less or increased in plants pretreated with CaCl(2); glutathione reductase (GR) activity increased under high temperature, and it increased more in plants pretreated with CaCl(2). There was an obvious accumulation of H(2)O(2) and O(2)(-) under high temperature, but CaCl(2) application decreased the contents of H(2)O(2) and O(2)(-) under heat stress conditions. Heat stress induced the level of heat shock protein 70 (HSP70), while CaCl(2) pretreatment enhanced it. These results suggested that photosynthesis was improved by CaCl(2) application in heat-stressed plants and such an improvement was associated with an improvement in stomatal conductance and the thermostability of oxygen-evolving complex (OEC), which might be due to less accumulation of reactive oxygen species. Copyright © 2011 Elsevier GmbH. All rights reserved.

The Evaluation of Damage Effects on MgO Added Concrete with Slag Cement Exposed to Calcium Chloride Deicing Salt

PubMed Central

Jang, Jae-Kyeong; Kim, Hong-Gi; Kim, Jun-Hyeong

2018-01-01

Concrete systems exposed to deicers are damaged in physical and chemical ways. In mitigating the damage from CaCl2 deicers, the usage of ground slag cement and MgO are investigated. Ordinary Portland cement (OPC) and slag cement are used in different proportions as the binding material, and MgO in doses of 0%, 5%, 7%, and 10% are added to the systems. After 28 days of water-curing, the specimens are immersed in 30% CaCl2 solution by mass for 180 days. Compressive strength test, carbonation test, chloride penetration test, chloride content test, XRD analysis, and SEM-EDAX analysis are conducted to evaluate the damage effects of the deicing solution. Up to 28 days, plain specimens with increasing MgO show a decrease in compressive strength, an increase in carbonation resistance, and a decrease in chloride penetration resistance, whereas the S30- and S50- specimens show a slight increase in compressive strength, an increase in carbonation resistance, and a slight increase in chloride penetration resistance. After 180 days of immersion in deicing solution, specimens with MgO retain their compressive strength longer and show improved durability. Furthermore, the addition of MgO to concrete systems with slag cement induces the formation of magnesium silicate hydrate (M-S-H) phases. PMID:29758008

Effect of Minocycline on the Durability of Dentin Bonding Produced with Etch-and-Rinse Adhesives.

PubMed

Loguercio, A D; Stanislawczuk, R; Malaquias, P; Gutierrez, M F; Bauer, J; Reis, A

2016-01-01

To evaluate the effect of minocycline and chlorhexidine pretreatment of acid-etched dentin on the longevity of resin-dentin bond strength (μTBS) and nanoleakage of two-step etch-and-rinse adhesives. Before application of Prime & Bond NT and Adper Single Bond 2 in occlusal dentin, the dentin surfaces were treated with 37% phosphoric acid, rinsed, air-dried, and rewetted with water (control group), 2% minocycline, or 2% chlorexidine digluconate. Composite buildups were constructed incrementally, and specimens were longitudinally sectioned to obtain bonded sticks (0.8 mm 2 ) to be tested in tension (0.5 mm/min) immediately or after 24 months of water storage. For nanoleakage, two specimens of each tooth/period were immersed in the silver nitrate solution, photo-developed, and polished with SiC paper for analysis under energy-dispersive X-ray spectroscopy/scanning electron microscopy. Reductions of the μTBS and increases in the nanoleakage were observed for both adhesives when the rewetting procedure was performed with water. Stable bonds were observed for the 2% minocycline and 2% chlorexidine digluconate groups after 24 months. The use of 2% minocycline as pretreatment of acid-etched dentin is one alternative to retard the degradation of resin-dentin interfaces over a 24-month period as well as 2% chlorexidine digluconate.

Methods for globally treating silica optics to reduce optical damage

DOEpatents

Miller, Philip Edward; Suratwala, Tayyab Ishaq; Bude, Jeffrey Devin; Shen, Nan; Steele, William Augustus; Laurence, Ted Alfred; Feit, Michael Dennis; Wong, Lana Louie

2012-11-20

A method for preventing damage caused by high intensity light sources to optical components includes annealing the optical component for a predetermined period. Another method includes etching the optical component in an etchant including fluoride and bi-fluoride ions. The method also includes ultrasonically agitating the etching solution during the process followed by rinsing of the optical component in a rinse bath.

Alginate Encapsulation of Begonia Microshoots for Short-Term Storage and Distribution

PubMed Central

Sakhanokho, Hamidou F.; Pounders, Cecil T.; Blythe, Eugene K.

2013-01-01

Synthetic seeds were formed from shoot tips of two in vitro grown Begonia cultivars using 3% sodium alginate in Murashige and Skoog medium (MS) salt solution as the gel matrix and 100 mM calcium chloride for complexation. Synthetic seed formation was achieved by releasing the sodium alginate/explant combination into 100 mM calcium chloride (CaCl2 ·H2O) solution for 30 or 45 min. Both control and encapsulated shoots were transferred into sterile Petri dishes and stored at 4°C or 22°C for 0, 2, 4, 6, or 8 weeks. Conversion of synthetic seeds into plantlets for both storage environments was assessed in MS medium or peat-based substrate. No significant difference was found between the 30 and 45 min CaCl2 ·H2O treatments or the two cultivars. Encapsulation of explants improved survival rate over time irrespective of the medium type or storage environment. Survival rates of 88, 53, 28, and 11% for encapsulated microshoots versus 73, 13, 0, and 0% for control explants were achieved in microshoots stored for 2, 4, 6, and 8 weeks, respectively. The best results were obtained when synthetic seeds were stored at 4°C and germinated on MS medium. Regenerated plantlets were successfully established in potting soil. PMID:24396296

A Simple Recipe for Whitening Old Newspaper Clippings.

ERIC Educational Resources Information Center

Carter, Henry A.

1995-01-01

Describes a method for experimenting with both whitening and deacidifying old newspaper clippings using sodium borohydride bleaching. Clippings are soaked in distilled water then immersed in sodium borohydride for 15-20 minutes. After rinsing with distilled water, the paper is washed with saturated Ca(OH)2 solution. Readers should not begin…

Examination of the steps leading up to the physical developer process for developing fingerprints.

PubMed

Wilson, Jeffrey Daniel; Cantu, Antonio A; Antonopoulos, George; Surrency, Marc J

2007-03-01

This is a systematic study that examines several acid prewashes and water rinses on paper bearing latent prints before its treatment with a silver physical developer. Specimens or items processed with this method are usually pretreated with an acid wash to neutralize calcium carbonate from the paper before the treatment with a physical developer. Two different acids at varying concentrations were tested on fingerprints. Many different types of paper were examined in order to determine which acid prewash was the most beneficial. Various wash times as well as the addition of a water rinse step before the development were also examined. A pH study was included that monitored the acidity of the solution during the wash step. Scanning electron microscopy was used to verify surface calcium levels for the paper samples throughout the experiment. Malic acid at a concentration of 2.5% proved to be an ideal acid for most papers, providing good fingerprint development with minimal background development. Water rinses were deemed unnecessary before physical development.

Immediate bonding properties of universal adhesives to dentine.

PubMed

Muñoz, Miguel Angel; Luque, Issis; Hass, Viviane; Reis, Alessandra; Loguercio, Alessandro Dourado; Bombarda, Nara Hellen Campanha

2013-05-01

To evaluate the dentine microtensile bond strength (μTBS), nanoleakage (NL), degree of conversion (DC) within the hybrid layer for etch-and-rinse and self-etch strategies of universal simplified adhesive systems. forty caries free extracted third molars were divided into 8 groups for μTBS (n=5), according to the adhesive and etching strategy: Clearfil SE Bond [CSE] and Adper Single Bond 2 [SB], as controls; Peak Universal Adhesive System, self-etch [PkSe] and etch-and-rinse [PkEr]; Scotchbond Universal Adhesive, self-etch [ScSe] and etch-and-rinse [ScEr]; All Bond Universal, self-etch [AlSe] and etch-and-rinse [AlEr]. After restorations were constructed, specimens were stored in water (37°C/24h) and then resin-dentine sticks were prepared (0.8mm(2)). The sticks were tested under tension at 0.5mm/min. Some sticks from each tooth group were used for DC determination by micro-Raman spectroscopy or nanoleakage evaluation (NL). The pH for each solution was evaluated using a pH metre. Data were analyzed with one-way ANOVA and Tukey's test (α=0.05). For μTBS, only PkSe and PkEr were similar to the respective control groups (p>0.05). AlSe showed the lowest μTBS mean (p<0.05). For NL, ScEr, ScSe, AlSe, and AlEr showed the lowest NL similar to control groups (p<0.05). For DC, only ScSe showed lower DC than the other materials (p<0.05). Performance of universal adhesives was shown to be material-dependent. The results indicate that this new category of universal adhesives used on dentine as either etch-and-rinse or self-etch strategies were inferior as regards at least one of the properties evaluated (μTBS, NL and DC) in comparison with the control adhesives (CSE for self-etch and SB for etch-and-rinse). Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of processing method and solute interactions on pepsin digestibility of cooked proso millet flour.

PubMed

Gulati, Paridhi; Sabillón, Luis; Rose, Devin J

2018-07-01

Previous studies have reported a substantial decline in in vitro digestibility of proso millet protein upon cooking. In this study, several processing techniques and cooking solutions were tested with the objective of preventing the loss in pepsin digestibility. Proso millet flour was subjected to the following processing techniques: high pressure processing (200 and 600 MPa for 5 and 20 min); germination (96 h); fermentation (48 h); roasting (dry heating); autoclaving (121 °C, 3 h), and treatment with transglutaminase (160 mg/g protein, 37 °C, 2 h). To study the interaction of millet proteins with solutes, millet flour was heated with sucrose (3-7 M); NaCl (2-6 M); and CaCl 2 (0.5-3 M). All processing treatments failed to prevent the loss in pepsin digestibility except germination and treatment with transglutaminase, which resulted in 23 and 39% increases in digestibility upon cooking, respectively, when compared with unprocessed cooked flours. Heating in concentrated solutions of sucrose and NaCl were effective in preventing the loss in pepsin digestibility, an effect that was attributed to a reduction in water activity (a w ). CaCl 2 was also successful in preventing the loss in digestibility but its action was similar to chaotrops like urea. Thus, a combination of enzymatic modification and cooking of millet flour with either naturally low a w substances or edible sources of chaotropic ions may be useful in processing of proso millet for development of novel foods without loss in digestibility. However, more research is required to determine optimum processing conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optimization of pH, temperature and CaCl2 concentrations for Ricotta cheese production from Buffalo cheese whey using Response Surface Methodology.

PubMed

Rashid, Abdul Ahid; Huma, Nuzhat; Zahoor, Tahir; Asgher, Muhammad

2017-02-01

The recovery of milk constituents from cheese whey is affected by various processing conditions followed during production of Ricotta cheese. The objective of the present investigation was to optimize the temperature (60-90 °C), pH (3-7) and CaCl2 concentration (2·0-6·0 mm) for maximum yield/recovery of milk constituents. The research work was carried out in two phases. In 1st phase, the influence of these processing conditions was evaluated through 20 experiments formulated by central composite design (CCD) keeping the yield as response factor. The results obtained from these experiments were used to optimize processing conditions for maximum yield using response surface methodology (RSM). The three best combinations of processing conditions (90 °C, pH 7, CaCl2 6 mm), (100 °C, pH 5, CaCl2 4 mm) and (75 °C, pH 8·4, CaCl2 4 mm) were exploited in the next phase for Ricotta cheese production from a mixture of Buffalo cheese whey and skim milk (9 : 1) to determine the influence of optimized conditions on the cheese composition. Ricotta cheeses were analyzed for various physicochemical (moisture, fat, protein, lactose, total solids, pH and acidity indicated) parameters during storage of 60 d at 4 ± 2 °C after every 15 d interval. Ricotta cheese prepared at 90 °C, pH 7 and CaCl2 6 mm exhibited the highest cheese yield, proteins and total solids, while high fat content was recorded for cheese processed at 100 °C, pH 5 and 4 mm CaCl2 concentration. A significant storage-related increase in acidity and NPN was recorded for all cheese samples.

The generation of HCl in the system CaCl2-H2O: Vapor-liquid relations from 380-500°C

USGS Publications Warehouse

Bischoff, James L.; Rosenbauer, Robert J.; Fournier, Robert O.

1996-01-01

We determined vapor-liquid relations (P-T-x) and derived critical parameters for the system CaCl2-H2O from 380-500??C. Results show that the two-phase region of this system is extremely large and occupies a significant portion of the P-T space to which circulation of fluids in the Earth's crust is constrained. Results also show the system generates significant amounts of HCl (as much as 0.1 mol/kg) in the vapor phase buffered by the liquid at surprisingly high pressures (???230 bars at 380??C, <580 bars at 500??C), presumably by hydrolysis of CaCl2: CaCl2 + 2H2O = Ca(OH)2 + 2HCl. We interpret the abundance of HCl in the vapor as due to its preference for the vapor phase, and by the preference of Ca(OH)2 for either the liquid phase or solid. The recent recognition of the abundance of CaCl2 in deep brines of the Earth's crust and their hydrothermal mobilization makes the hydrolysis of CaCl2 geologically important. The boiling of Ca-rich brines produces abundant HCl buffered by the presence of the liquid at moderate pressures. The resultant Ca(OH)2 generated by this process reacts with silicates to form a variety of alteration products, such as epidote, whereas the vapor produces acid-alteration of rocks through which it ascends.

Self-assembly of DNA functionalized gold nanoparticles at the liquid-vapor interface

DOE PAGES

Zhang, Honghu; Wang, Wenjie; Hagen, Noah; ...

2016-05-30

Here, surface sensitive synchrotron X-ray scattering and spectroscopy are used to monitor and characterize the spontaneous formation of 2D Gibbs monolayers of thiolated single-stranded DNA-functionalized gold nanoparticles (ssDNAAuNPs) at the vapor–solution interface by manipulating salt concentrations. Grazing incidence small-angle X-ray scattering and X-ray refl ectivity show that the noncomplementary ssDNA-AuNPs dispersed in aqueous solution spontaneously accumulate at the vapor–liquid interface in the form of a single layer by increasing MgCl 2 or CaCl 2 concentrations. Furthermore, the monoparticle layer undergoes a transformation from short- to long-range (hexagonal) order above a threshold salt-concentration. Using various salts at similar ionic strength tomore » those of MgCl 2 or CaCl 2 such as, NaCl or LaCl 3, it is found that surface adsorbed NPs lack any order. X-ray fluorescence near total reflection of the same samples provides direct evidence of interfacial gold and more importantly a significant surface enrichment of the cations. Quantitative analysis reveals that divalent cations screen the charge of ssDNA, and that the hydrophobic hexyl-thiol group, commonly used to functionalize the ssDNA (for capping the AuNPs), is likely the driving force for the accumulation of the NPs at the interface.« less

Encapsulation of Lactobacillus kefiri in alginate microbeads using a double novel aerosol technique.

PubMed

Demitri, Christian; Lamanna, Leonardo; De Benedetto, Egidio; Damiano, Fabrizio; Cappello, Maria Stella; Siculella, Luisa; Sannino, Alessandro

2017-08-01

Alginate micro beads containing Lactobacillus kefiri (the principal bacteria present in the kefir probiotic drink) were produced by a novel technique based on dual aerosols spaying of alginate based solution and CaCl 2 as cross linking agent. Carboxymethylcellulose (CMC) has been also added to the alginate in order to change the physic-chemical properties (viscosity and permeability) of the microbeads. Calcium alginate and CMC are biopolymers that can be used for developing oral drug-delivery systems. These biopolymers have been reported to show a pH-dependent swelling behaviour. Calcium alginate and CMC have also been known to possess an excellent mucoadhesive property. The loaded microbeads have been characterized in terms of morphology, chemical composition and stability in different conditions mimicking the gastric environment. In this study, we demonstrate the feasibility of a continuous fabrication of alginate microbeads in a range of 50-70μm size, encapsulating L. kefiri as active ingredient. The technique involves the use of a double aerosols of alginate based solution and CaCl 2 as crosslinking agent. Moreover, the encapsulation process was proved to be effective and not detrimental to bacteria viability. At the same time, it was verified the protective efficacy of the microcapsules against the gastric environment using both SGF pH1.2 (fasted state) and pH2.2 (feed state). Copyright © 2017 Elsevier B.V. All rights reserved.

Study of the Effectiveness of Multipurpose Solutions on the Bacterial Disinfection of Silicone Hydrogel Contact Lenses In Vitro.

PubMed

Correa, Priscila C; Lui, Aline C F; Silva, Cely B; Gracitelli, Carolina P B; Mimica, Lycia M; Sasagawa, Suzethe M; Netto, Adamo L

2017-10-12

To assess the antimicrobial effectiveness of multipurpose solutions in regard to the disinfection of silicone hydrogel contact lenses (CL) using a study of clinical bacterial isolates from ocular material. Three multipurpose solutions (solution A: polyhexamethylene biguanide 0.00025 g/100 mL; solution B: polyquaternary-1 0.001% and myristamidopropyl dimethylamine 0.0006%; and solution C: polyaminopropyl biguanide 0.00013% and polyquaternary 0.0001%) were used as a 3-phase disinfection on silicone hydrogel CL contaminated with bacteria from clinical isolates that were divided into five groups (group 1: Pseudomonas aeruginosa; group 2: Staphylococcus aureus; group 3: Staphylococcus epidermidis; group 4: Streptococcus spp; and group 5: enterobacteria). No differences were observed between the 24- and 48-hr measurements in any of the samples, and the positivity of microorganisms in T0 was 100% for all solutions; it was 0% in T3. Therefore, only steps T1 (rubbing followed by rinsing) and T2 (rubbing followed by rinsing and immersion of CL into solution) were considered for analysis at the 24-hr measurement time. Throughout the phases, a decrease in the number of bacteria was observed, culminating in the elimination (no recovery) of all microorganisms in the three solutions. At the end of the proposed process, the tested solutions were effective.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

Chemical milling solution reveals stress corrosion cracks in titanium alloy

NASA Technical Reports Server (NTRS)

Braski, D. N.

1967-01-01

Solution of hydrogen flouride, hydrogen peroxide, and water reveals hot salt stress corrosion cracks in various titanium alloys. After the surface is rinsed in water, dried, and swabbed with the solution, it can be observed by the naked eye or at low magnification.

CaCl 2 -Accelerated Hydration of Tricalcium Silicate: A STXM Study Combined with 29 Si MAS NMR

DOE PAGES

Li, Qinfei; Ge, Yong; Geng, Guoqing; ...

2015-01-01

Tmore » he effect of calcium chloride (CaCl 2 ) on tricalcium silicate (C 3 S) hydration was investigated by scanning transmission X-ray microscopy (SXM) with Near Edge X-ray Absorption Fine Structure (NEXAFS) spectra and 29 Si MAS NMR. SXM is demonstrated to be a powerful tool for studying the chemical composition of a cement-based hydration system. he Ca L 3,2 -edge NEXAFS spectra obtained by examining C 3 S hydration in the presence of CaCl 2 showed that this accelerator does not change the coordination of calcium in the calcium silicate hydrate (C-S-H), which is the primary hydration product. O K-edge NEXAFS is also very useful in distinguishing the chemical components in hydrated C 3 S. Based on the Ca L 3,2 -edge spectra and chemical component mapping, we concluded that CaCl 2 prefers to coexist with unhydrated C 3 S instead of C-S-H. In Si K-edge NEXAFS analysis, CaCl 2 increases the degree of silicate polymerization of C-S-H in agreement with the 29 Si CP/MAS NMR results, which show that the presence of CaCl 2 in hydrated C 3 S considerably accelerates the formation of middle groups ( Q 2 ) and branch sites ( Q 3 ) in the silicate chains of C-S-H gel at 1-day hydration.« less

Deposition kinetics of extracellular polymeric substances (EPS) on silica in monovalent and divalent salts.

PubMed

Zhu, Pingting; Long, Guoyu; Ni, Jinren; Tong, Meiping

2009-08-01

The deposition kinetics of extracellular polymeric substances (EPS) on silica surfaces were examined in both monovalent and divalent solutions under a variety of environmentally relevant ionic strength and pH conditions by employing a quartz crystal microbalance with dissipation (DCM-D). Soluble EPS (SEPS) and bound EPS (BEPS) were extracted from four bacterial strains with different characteristics. Maximum favorable deposition rates (k(fa)) were observed for all EPS at low ionic strengths in both NaCl and CaCl2 solutions. With the increase of ionic strength, k(fa) decreased due to the simultaneous occurrence of EPS aggregation in solutions. Deposition efficiency (alpha; the ratio of deposition rates obtained under unfavorable versus corresponding favorable conditions) for all EPS increased with increasing ionic strength in both NaCl and CaCl2 solutions, which agreed with the trends of zeta potentials and was consistent with the classic Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. Comparison of alpha for SEPS and BEPS extracted from the same strain showed that the trends of alpha did not totally agree with trends of zeta potentials, indicating the deposition kinetics of EPS on silica surfaces were not only controlled by DLVO interactions, but also non-DLVO forces. Close comparison of alpha for EPS extracted from different sources showed alpha increased with increasing proteins to polysaccharides ratio. Subsequent experiments for EPS extracted from the same strain but with different proteins to polysaccharides ratios and from activated sludge also showed that alpha were largest for EPS with greatest proteins to polysaccharides ratio. Additional experiments for pure protein and solutions with different pure proteins to pure saccharides ratios further corroborated that larger proteins to polysaccharides ratio resulted in greater EPS deposition.

Effects of carbohydrate mouth rinse and caffeine on high-intensity interval running in a fed state.

PubMed

Devenney, Simon; Mangan, Shane; Shortall, Marcus; Collins, Kieran

2018-05-01

The current study aims to identify if mouth rinsing with a 6% carbohydrate mouth-rinse (CMR) solution and mouth rinsing and ingestion of caffeine (CMR+CAFF) can affect exercise performance during steady-state (SS) running and high-intensity intervals (HIIT) in comparison with a 0% control solution (PLA) when in a fed state. Eight recreationally trained males completed 3 trials (CMR, CMR+CAFF, and PLA) of 45 min SS running and an HIIT protocol (90% peak treadmill velocity) until fatigue in a double blinded, repeated-measures study. Participants ingested a capsule of either CAFF or PLA before and after SS. Participants received a 25-mL bolus of carbohydrate solution (CMR and CMR+CAFF trials) or taste-matched PLA (PLA trial) prior to HIIT protocol and after every second effort. Heart rate and lactate responses were recorded throughout the SS and HIIT protocol. CMR+CAFF was significantly different when compared with PLA (p = 0.001; Cohens d = 1.34) and CMR (p = 0.031; Cohens d = 0.87) in relation to distance covered before fatigue. Although there was no significant difference between CMR and PLA, there was a small benefit for CMR (p = 0.218; Cohens d = 0.46). Results indicate that CMR and ingestion of CAFF leads to improvements in performance during interval sessions while participants were in a fed state. These findings indicate that the regular use of CMR can decrease the risk of gastrointestinal distress reported by athletes, which can be applicable to athletes in a real-world setting.

Desorption of zinc by extracellularly produced metabolites of Trichoderma harzianum, Trichoderma reesei and Coriolus versicolor.

PubMed

Adams, P; Lynch, J M; De Leij, F A A M

2007-12-01

To determine the role of fungal metabolites in the desorption of metals. Desorption of Zn from charcoal by three different fungi was compared against metal desorption with reverse osmosis water, a 0.1% Tween 80 solution and a 0.1 mol l(-1) CaCl(2) solution. All three fungal filtrates desorbed three times more Zn than either 0.1% Tween 80 or 0.1 mol l(-1) CaCl(2). Metal chelator production in Trichoderma harzianum and Coriolus versicolor was constitutively expressed while chelator production in Trichoderma reesei was induced by Zn. The presence of Zn inhibited the production of metal chelators by C. versicolor. Only C. versicolor was found to produce oxalic acid (a strong metal chelator). All fungi caused a marked decrease in pH, although this was not enough to explain the increased desorption of the metals by the different fungal filtrates. Metal chelation via organic acids and proteins are the main mechanisms by which the fungal filtrates increase zinc desorption. The results of this study explain why plants inoculated with T. harzianum T22 take up more metal from soil, than noninoculated plants while metabolites produced by fungi could be used for metal leaching from contaminated soils.

Root caries prevention via sodium fluoride, chlorhexidine and silver diamine fluoride in vitro.

PubMed

Göstemeyer, Gerd; Kohls, Anna; Paris, Sebastian; Schwendicke, Falk

2018-01-31

Uncertainty exists as to how to best prevent root caries development. The aim of the present study was to compare sodium fluoride (NaF), chlorhexidine (CHX) and silver diamine fluoride (SDF) varnishes (V) and rinses (R) regarding their caries preventive effect in an artificial caries biofilm model. 140 bovine root dentin samples were cut, polished and embedded. Samples were allocated to seven treatment groups (n = 20/group): Four varnishes (applied once prior biofilm challenge): 38% SDF (SDFV), 35% CHX-varnish (CHXV), 22,600 ppm NaF-varnish (NaFV), placebo-varnish (PV); two rinses (applied once daily during biofilm challenge): 500 ppm NaF solution (NaFR), 0.1% CHX solution (CHXR); one untreated group. Caries was induced in a multi-station, continuous-culture Lactobacillus rhamnosus GG (LGG) biofilm model. Bacteria were inoculated 1 × daily, while 2% sucrose was supplied 8 ×/day followed by artificial saliva for 10 min. After 12 days, mineral loss (ΔZ) was measured in the effect area and adjacent to the varnished areas. Bacterial counts were assessed on de-Man-Rogosa-Sharpe agar. ΔZ was significantly lower in the NaFR group compared with all other groups. Varnishes did not significantly prevent mineral loss in adjacent areas. None of the agents had a significant antimicrobial effect on LGG. Regular fluoride rinses showed highest root caries-preventive effect.

No Dose-Response Effect of Carbohydrate Mouth Rinse Concentration on 5-km Running Performance in Recreational Athletes.

PubMed

Clarke, Neil D; Thomas, James R; Kagka, Marion; Ramsbottom, Roger; Delextrat, Anne

2017-03-01

Clarke, ND, Thomas, JR, Kagka, M, Ramsbottom, R, and Delextrat, A. No dose-response effect of carbohydrate mouth rinse concentration on 5-km running performance in recreational athletes. J Strength Cond Res 31(3): 715-720, 2017-Oral carbohydrate rinsing has been demonstrated to provide beneficial effects on exercise performance of durations of up to 1 hour, albeit predominately in a laboratory setting. The aim of the present study was to investigate the effects of different concentrations of carbohydrate solution mouth rinse on 5-km running performance. Fifteen healthy men (n = 9; mean ± SD age; 42 ± 10 years; height, 177.6 ± 6.1 cm; body mass, 73.9 ± 8.9 kg) and women (n = 6; mean ± SD age, 43 ± 9 years; height, 166.5 ± 4.1 cm; body mass, 65.7 ± 6.8 kg) performed a 5-km running time trial on a track on 4 separate occasions. Immediately before starting the time trial and then after each 1 km, subjects rinsed 25 ml of 0, 3, 6, or 12% maltodextrin for 10 seconds. Mouth rinsing with 0, 3, 6, or 12% maltodextrin did not have a significant effect on the time to complete the time trial (0%, 26:34 ± 4:07 minutes:seconds; 3%, 27:17 ± 4:33 minutes:seconds; 6%, 27:05 ± 3:52 minutes:seconds; 12%, 26:47 ± 4.31 minutes:seconds; p = 0.071; (Equation is included in full-text article.)= 0.15), heart rate (p = 0.095; (Equation is included in full-text article.)= 0.16), rating of perceived exertion (p = 0.195; (Equation is included in full-text article.)= 0.11), blood glucose (p = 0.920; (Equation is included in full-text article.)= 0.01), and blood lactate concentration (p = 0.831; (Equation is included in full-text article.)= 0.02), with only nonsignificant trivial to small differences between concentrations. Results of this study suggest that carbohydrate mouth rinsing provides no ergogenic advantage over an acaloric placebo (0%) and that there is no dose-response relationship between carbohydrate solution concentration and 5-km track running performance.

In Vitro Ability of a Novel Nanohydroxyapatite Oral Rinse to Occlude Dentine Tubules

PubMed Central

Hill, Robert G.; Chen, Xiaohui; Gillam, David G.

2015-01-01

Objectives. The aim of the study was to investigate the ability of a novel nanohydroxyapatite (nHA) desensitizing oral rinse to occlude dentine tubules compared to selected commercially available desensitizing oral rinses. Methods. 25 caries-free extracted molars were sectioned into 1 mm thick dentine discs. The dentine discs (n = 25) were etched with 6% citric acid for 2 minutes and rinsed with distilled water, prior to a 30-second application of test and control oral rinses. Evaluation was by (1) Scanning Electron Microscopy (SEM) of the dentine surface and (2) fluid flow measurements through a dentine disc. Results. Most of the oral rinses failed to adequately cover the dentine surface apart from the nHa oral rinse. However the hydroxyapatite, 1.4% potassium oxalate, and arginine/PVM/MA copolymer oral rinses, appeared to be relatively more effective than the nHA test and negative control rinses (potassium nitrate) in relation to a reduction in fluid flow measurements. Conclusions. Although the novel nHA oral rinse demonstrated the ability to occlude the dentine tubules and reduce the fluid flow measurements, some of the other oral rinses appeared to demonstrate a statistically significant reduction in fluid flow through the dentine disc, in particular the arginine/PVM/MA copolymer oral rinse. PMID:26161093

Quantifying In Situ Contaminant Mobility in Marine Sediments

DTIC Science & Technology

2008-01-01

and rinsing the collection and sensor chambers and the circulation subsystem with prepared solutions is followed. For metals, a nitric acid soak/rinse...fluids beginning with tap water, then de-ionized water, then a special detergent (“RBS”), then de- ionized water, then nitric acid for metals or Methanol...component parts are soaked, four-hours minimum, in each fluid. A 25% concentration of ultra-pure nitric acid is used to soak Teflon™ parts (bottles, lids

Corrosion behavior of ion implanted nickel-titanium orthodontic wire in fluoride mouth rinse solutions.

PubMed

Iijima, Masahiro; Yuasa, Toshihiro; Endo, Kazuhiko; Muguruma, Takeshi; Ohno, Hiroki; Mizoguchi, Itaru

2010-01-01

This study investigated the corrosion properties of ion implanted nickel-titanium wire (Neo Sentalloy Ionguard) in artificial saliva and fluoride mouth rinse solutions (Butler F Mouthrinse, Ora-Bliss). Non ion implanted nickel-titanium wire (Neo Sentalloy) was used as control. The anodic corrosion behavior was examined by potentiodynamic polarization measurement. The surfaces of the specimens were examined with SEM. The elemental depth profiles were characterized by XPS. Neo Sentalloy Ionguard in artificial saliva and Butler F Mouthrinse (500 ppm) had a lower current density than Neo Sentalloy. In addition, breakdown potential of Neo Sentalloy Ionguard in Ora-Bliss (900 ppm) was much higher than that of Neo Sentalloy although both wires had similar corrosion potential in Ora-Bliss (450 and 900 ppm). The XPS results for Neo Sentalloy Ionguard suggested that the layers consisted of TiO(2) and TiN were present on the surface and the layers may improve the corrosion properties.

RNA Seq analysis of the role of calcium chloride stress and electron transport in mitochondria for malachite green decolorization by Aspergillus niger.

PubMed

Gomaa, Ola M; Selim, Nabila S; Wee, Josephine; Linz, John E

2017-08-01

Aspergillus niger was previously demonstrated to decolorize the commercial dye malachite green (MG) and this process was enhanced under calcium chloride (CaCl 2 ) treatment. Previous data also suggested that the decolorization process is related to mitochondrial cytochrome c. In the current work, we analyzed in depth the specific relationship between CaCl 2 treatment and MG decolorization. Gene expression analysis (RNA Seq) using Next Generation Sequencing (NGS) revealed up-regulation of 28 genes that are directly or indirectly associated with stress response functions as early as 30min of CaCl 2 treatment; these data further strengthen our previous findings that CaCl 2 treatment induces a stress response in A. niger which enhances the ability to decolorize MG. A significant increase in fluorescence observed by MitoTracker dye suggests that CaCl 2 treatment also increased mitochondrial membrane potential. Isolated mitochondrial membrane protein fractions obtained from A. niger grown under standard growth conditions decolorized MG in the presence of NADH and decolorization was enhanced in samples isolated from CaCl 2 -treated A. niger cultures. Treatment of whole mitochondrial fraction with KCN which inhibits electron transport by cytochrome c oxidase and Triton-X 100 which disrupts mitochondrial membrane integrity suggests that cyanide sensitive cytochrome c oxidase activity is a key biochemical step in MG decolorization. This suggestion was confirmed by the addition of palladium α-lipoic acid complex (PLAC) which resulted in an initial increase in decolorization. Although the role of cytochrome c and cytochrome c oxidase was confirmed at the biochemical level, changes in levels of transcripts encoding these enzymes after CaCl 2 treatment were not found to be statistically significant in RNA Seq analysis. These data suggest that the regulation of cytochrome c enzymes occur predominantly at the post-transcriptional level under CaCl 2 stress. Thus, using global transcriptomics and biochemical approaches, our study provides a molecular association between fungal mitochondrial electron transfer systems and MG decolorization. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of application of a PVP-iodine solution before and during subgingival ultrasonic instrumentation on post-treatment bacteraemia: a randomized single-centre placebo-controlled clinical trial.

PubMed

Sahrmann, Philipp; Manz, Andrea; Attin, Thomas; Zbinden, Reinhard; Schmidlin, Patrick R

2015-07-01

To assess the effect of concomitant subgingival rinsing with 10% PVP-iodine during subgingival instrumentation on the prevalence and magnitude of bacteraemia of oral origin. Subgingival instrumentation was performed with water or PVP-iodine rinse in patients with periodontitis. Prior to instrumentation, subjects gargled for 1 min with the allocated liquid. Pockets were then rinsed for 1 min and subgingivally instrumented with liquid-cooled (water/PVP-iodine) ultrasonic scalers (1 min). Two minutes later, a blood sample from the arm vein was drawn using a lysis centrifugation blood culture system for quantitative microbiological analysis. Non-parametric statistical tests were performed to assess differences in the prevalence and extent of bacteraemia between groups. Of the 19 samples in each group, oral-borne bacteraemia was detected in 10 of the control and 2 of the test samples. With an average of 3.0 [1; 5] colony forming units, significantly less bacteria and bacteraemia were found in the test group compared to the controls (12.2 [1; 46]) (p = 0.003). Anaerobic bacteria were not found in the test group. Bacteraemia after subgingival instrumentation with concomitant PVP-iodine rinsing is reduced but not eliminated. Therefore, it might be recommended for patients at a high risk of endocarditis or infection of endoprostheses. However, preventive antibiotic treatment should not be omitted. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

NASA Astrophysics Data System (ADS)

Johnson, Paul; Thomas, Elena C.; Hodyss, Robert; Vu, Tuan; Choukroun, Mathieu

2016-10-01

Currently, our understanding of the chemical composition of Europa's surface is our best means of inferring constraints on the subsurface ocean composition and its subsequent habitability. The bulk of our knowledge of Europa surface chemistry can be traced to near infrared spectra recorded by the Near Infrared Mapping Spectrometer on the Galileo spacecraft. However, the usefulness of this and other remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Chloride salts are expected to exist on the surface of Europa, and other icy bodies, based on geochemical predictions of the ocean composition. In order to help improve our understanding of Europa's surface composition, we have conducted a study of frozen chloride-salt brines prepared under simulated Europa surface conditions (vacuum, temperature, and UV irradiation) using both near IR and Raman spectroscopies. Specifically, Raman spectroscopy was used to determine the hydration states of various chloride salts as a function of temperature. Near IR spectroscopy of identically prepared samples was used to provide reference reflectance spectra of the identified hydrated salts. Our results indicate that at temperatures ranging from 80 K to 233 K, hydrohalite is formed from the freezing of NaCl brines, while the freezing of KCl solutions does not form KCl hydrates. In addition, the freezing of MgCl2 solutions forms a stable hexahydrate, and the freezing of CaCl2 solutions forms a hexahydrate, a tetrahydrate, and a dihydrate. Dehydration of the salts was observed as temperatures were increased, leading to a succession of hydration states in the case of CaCl2.

[Feasibility of washing as a remediation technology for the heavy metals-polluted soils left by chemical plant].

PubMed

Liu, Lei; Hu, Shao-Ping; Chen, Ying-Xu; Li, Hang

2010-06-01

Laboratory simulation tests were conducted to examine the effects of different washing reagents (distilled water, HCl, H3PO4, oxalic acid, and CaCl2) in extracting the heavy metals from contaminated soils left by a chemical plant. The effects of reagent concentration, reaction time, and washing time on the washing efficiency were investigated, and the form variation of test heavy metals was determined before and after HCl washing. Distilled water, H3PO4, and CaCl2 could remove less than 1% of most heavy metals, and the highest removal rate was only 3.58%; while 2 mol HCl x L(-1) could obtain the highest washing efficiency under the optimal conditions, i. e., soil:liquid ratio was 1:3, reaction time was 1 hour, and the soils were washed twice by HCl solution. The removal rates of Cr, Pb, Zn, Cu, and Cd from test soils were 80.75%, 88.69%, 98.00%, 79.33%, and 95.52%, respectively. Among the washing reagents, HCl could effectively remove all forms of heavy metals.

The Anticaries Effect of a Food Extract (Shiitake) in a Short-Term Clinical Study

PubMed Central

Lingström, Peter; Zaura, Egija; Hassan, Haidar; Buijs, Mark J.; Hedelin, Pamie; Pratten, Jonathan; Spratt, David; Daglia, Maria; Karbowiak, Aneta; Signoretto, Caterina; Rosema, Martijn; van der Weijden, Fridus; Wilson, Michael

2012-01-01

The main objective was to investigate whether low-molecular-weight fraction of edible mushroom shiitake extract (Lentinus edodes) possesses caries-preventive properties. The study was designed as a double-blind, three-leg, cross-over, randomized, controlled clinical trial carried out on two series of volunteers at the University of Gothenburg, and the Academic Centre for Dentistry Amsterdam. Volunteers rinsed twice daily with a solution containing low-molecular-weight fraction of edible mushroom, placebo (negative control without active ingredients), or Meridol (positive control, AmF-SnF2) for two weeks, with a two-week washout period between each rinsing period. Changes in the acidogenicity of dental plaque before and after a sucrose challenge, shifts in microbial composition, and plaque scores were determined. Frequent rinses with shiitake reduced the metabolic activity of dental plaque. No reduction of plaque scores and no inhibition of the production of organic acids in plaque was found. Minor differences in microbial composition between test sessions were found. To conclude, the results indicate that shiitake extract has anticariogenic potential, but not to the same extent as the positive control. PMID:22500081

SURFACE TREATMENT OF MOLYBDENUM METAL

DOEpatents

Coffer, C.O.

1961-12-01

A process of descaling molybdenum articles comprises first immersing them in an aqueous sodium hydroxide-potassium permanganate solution of between 60 and 85 deg C, rinsing, and then immersing them in an aqueous solution containing a mixture of sulfuric, hydrochloric, and chromic acids.

Comparison of test methods to screen for residual chemical contamination on medical device surfaces.

PubMed

Kulkarni, Prachi; Shoff, Megan; Lucas, Anne

2012-01-01

Reprocessing medical devices involves several steps including cleaning and disinfection or sterilization. Chemical residuals can occur at various stages of reprocessing. These residues could interfere with device function and potentially harm patients. These solutions are composed of a combination of various chemicals and their residues are highly diluted post rinsing, therefore, it is difficult to find a sensitive and rapid method to detect toxicity due to chemical residues. This study focused on (1) finding the levels of residues that are cytotoxic using two mammalian cell lines and Daphnia magna, and (2) evaluating two test methods, Total Organic Carbon (TOC) and the Luminescent Bacteria Test (LBT), to measure residual chemicals levels. The two mammalian cell lines were equal in their cytotoxicity responses. However, Daphnia were more sensitive to some chemical residue than the two mammalian cell lines. TOC and LBT were able to detect the presence of residue well below the levels that were determined to cause mammalian cytotoxicity. LBT was more sensitive for some chemicals and TOC for others, both in solution and in simulated cleaning and rinsing for the limited number of solutions tested in this study.

Salivary pH after a glucose rinse: effect of a new mucoadhesive spray (Cariex) based on sodium bicarbonate and xylitol.

PubMed

Abbate, G M; Levrini, L; Caria, M P

2014-01-01

This study evaluated whether sodium bicarbonate applied on the oral mucosa through a new mucoadhesive spray (Cariex) could control a drop in salivary pH after a glucose rinse, and therefore enhance the buffering potential of saliva. A sample of 50 healthy adults was selected. At day 1, the measurement of salivary pH was performed in the lower fornix in correspondence with the lower molars. Each subject rinsed with 10 ml of a 10% glucose solution and then pH was monitored continually for 40 minutes. At day 2, the same experimental procedure was repeated and three shots of the spray were administered on the oral mucosa. The tested spray is composed of sodium bicarbonate, xylitol, and excipients. Without the mucoadhesive spray, salivary pH became significantly lower following the glucose rinse (p < 0.01). Following the spray, the time in which the pH remained lower than 6.0 was reduced statistically significantly (p < 0.01). A continual rise of salivary pH was observed for the 40 minutes in which the pH recording was performed. Conclusions: The use of a sodium bicarbonate spray on the mucosa was shown to control the lowering of salivary pH following carbohydrate consumption, and might therefore add to the prevention of caries and dental erosion.

Effect of calcium and light on the germination of Urochondra setulosa under different salts*

PubMed Central

Shaikh, Faiza; Gul, Bilquees; Li, Wei-qiang; Liu, Xiao-jing; Khan, M. Ajmal

2007-01-01

Urochondra setulosa (Trin.) C.E. Hubbard is a coastal halophytic grass thriving on the coastal dunes along the Pakistani seashore. This grass could be useful in coastal sand dune stabilization using seawater irrigation. The purpose of this investigation was to test the hypothesis that Ca2+ (0.0, 2.5, 5.0, 10.0 and 50.0 mmol/L) alleviates the adverse effects of KCl, MgSO4, NaCl and Na2SO4 at 0, 200, 400, 600, 800 and 1000 mmol/L on the germination of Urochondra setulosa. Seed germination was inhibited with increase in salt concentration with few seeds germinated at and above 400 mmol/L concentration. No seed germinated in any of the KCl treatments. Inclusion of CaCl2 substantially alleviated the inhibitory effects of all salts. Germination was higher under photoperiod in comparison to those seeds germinated under complete darkness. Among the CaCl2 concentrations used, 10 mmol/L was most effective in alleviating salinity effects and allowing few seeds to germinate at 1000 mmol/L KCl, MgSO4, NaCl and Na2SO4 solution. PMID:17173358

A comparison of Listerine® and sodium bicarbonate oral cleansing solutions on dental plaque colonisation and incidence of ventilator associated pneumonia in mechanically ventilated patients: a randomised control trial.

PubMed

Berry, A M

2013-10-01

Effective oral hygiene has been proposed as a key factor in the reduction of dental plaque colonisation and subsequent development of ventilator associated pneumonia (VAP). Listerine(®) oral rinse, while used extensively in dental practice has rarely been tested in mechanically ventilated patients. Sodium bicarbonate as an oral rinse has been more commonly utilised in oral hygiene regimens in intensive care patients. To test the efficacies of the essential oil mouth rinse, Listerine(®) (Pfizer) and sodium bicarbonate in the reduction of dental plaque colonisation with respiratory pathogens and the subsequent development of VAP. The study design was a prospective, single blind randomised comparative study of adult patients mechanically ventilated for at least 4 days. Patients were randomised to Listerine(®) (Pfizer) oral rinse twice daily, sodium bicarbonate oral rinse 2/24 or sterile water 2/24 (control group). All groups received tooth brushing 3 times a day. Dental plaque colonisation (primary outcome) and incidence of ventilator associated pneumonia (secondary outcome) were studied. Three hundred and ninety-eight patients were randomised to either the Listerine group (127), sodium bicarbonate group (133) or the control group (138). Baseline characteristics were similar for all groups. There were no significant differences between the control and study groups in colonisation of dental plaque at Day 4 (p=0.243). Ventilator associated pneumonia was diagnosed in 18 patients. The incidence was, Listerine(®) group 4.7%, sodium bicarbonate group 4.5% and control 4.3% [OR, 0.99; 95% CI, 0.31 to 3.16; p=0.92]. Compared to the control group, Listerine(®) or sodium bicarbonate oral rinses were not more effective in the reduction of colonisation of dental plaque or the incidence of VAP. Given the low incidence of VAP, the common factor of a small, soft toothbrush as part of an oral hygiene regimen suggests possible benefit in mechanically ventilated patients. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

The effect of different mouth rinse products on intra-oral halitosis.

PubMed

Erovic Ademovski, S; Lingström, P; Renvert, S

2016-05-01

To evaluate the effect of different mouth rinses 12 h after rinsing on genuine intra-oral halitosis. Twenty-four adults with halitosis were included in a double-blind, crossover, randomized clinical trial. Halitosis was evaluated 12 h after rinsing with placebo and five mouth rinse products containing zinc acetate and chlorhexidine diacetate; zinc lactate, chlorhexidine and cetylpyridinium chloride; zinc acetate and chlorhexidine diacetate with reduced amounts of mint and menthol; zinc chloride and essential oil; and chlorine dioxide using the organoleptic method and a gas chromatograph. Test periods were separated by 1 week. Hydrogen sulphide (H2 S), methyl mercaptan (MM) and the organoleptic scores (OLS) were significantly reduced 12 h following rinsing with all substances compared to placebo (P < 0.05). H2 S was more effectively reduced after rinsing with zinc acetate and chlorhexidine diacetate and zinc acetate and chlorhexidine diacetate with reduced amounts of mint and menthol compared to rinsing with zinc chloride and essential oil (P < 0.05), and significantly lower values of MM were obtained after rinsing with zinc acetate and chlorhexidine diacetate compared to zinc lactate, chlorhexidine and cetylpyridinium chloride (P < 0.05). The percentage effectively treated individuals (H2 S (<112 ppb), MM (<26 ppb) and OLS score <2) varied from 58% percentage (zinc acetate and chlorhexidine diacetate) to 26% (zinc chloride and essential oil). All treatments resulted in reduction in halitosis 12 h after rinsing compared to placebo. H2 S and MM were most effectively reduced by zinc acetate and chlorhexidine diacetate. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Chemometric analysis of the consumption of oral rinse chlorite (ClO2-) by human salivary biomolecules.

PubMed

Chang, Hubert; Blackburn, John; Grootveld, Martin

2013-12-01

Oral rinse formulations containing chlorite anion (ClO(2)(-)) as an active agent exert a range of valuable oral healthcare activities. However, salivary biomolecules which chemically react with this oxidant can, at least in principle, serve as potentially significant barriers to these therapeutic properties in the oral environment. Therefore, in this investigation, we have explored the extent of ClO(2)(-) consumption by biomolecules which scavenge this agent in human salivary supernatants (HSSs) in vitro. HSS samples were equilibrated with oral rinse formulations containing this active agent (30 s at 35 °C in order to mimic oral rinsing episodes). Differential spectrophotometric and ion-pair reversed-phase high-performance liquid chromatographic analyses were employed to determine residual ClO(2)(-) in these admixtures. Bioanalytical data acquired revealed the rapid consumption of ClO(2)(-) by biomolecular electron donors and/or antioxidants present in HSS samples. Mean ± 95 % confidence interval (CI) consumption levels of 7.14 ± 0.69 and 5.34 ± 0.69 % of the total ClO(2)(-) available were found for oral rinse products containing 0.10 and 0.40 % (w/v) ClO(2)(-), respectively. A mixed model analysis-of-variance performed on experimental data acquired demonstrated highly-significant differences between oral rinse ClO(2)(-) contents (p < 0.0001), trial participants (p < 0.001) and sampling days-within-participants (p < 0.001), and also revealed non-additive ClO(2)(-)-scavenging responses of participants' HSSs to increases in the oral rinse content of this oxidant (p < 0.0001). A slower, second phase of the reaction process (t (1/2) = 1.7-2.8 h) involved the oxidative consumption of salivary urate. These data clearly demonstrate that for recommended 30 s oral rinsing episodes performed at physiological temperature, <10 % of the total oral rinse ClO(2)(-) available is chemically and/or reductively consumed by HSS biomolecules for both oral rinse formulations investigated. These observations are of much clinical significance in view of the retention of these products' active agent, i.e. <10 % of ClO(2)(-) is consumed by HSS biomolecules within recommended 30 s oral rinsing episodes, and hence, the bulk of this oxyhalogen oxidant (>90 %) may effectively exert its essential microbicidal, anti-periodontal and oral malodour-neutralising actions.

Role of solution chemistry in the retention and release of ...

EPA Pesticide Factsheets

Upon increasing production and use of graphene oxide nanoparticles (GONPs), concerns agitate over their potential impacts and risks to the environment, ecosystem, and human health. An improved understanding of the fate and transport including remobilization of GONPs in the subsurface environment enables us to better expedite the benign use of GONPs in a sustainable fashion but also evaluate their environmental impacts and health risks. In this study, the deposition and release of GONPs were systematically examined in water-saturated columns packed with either uncoated sand or iron oxide-coated sand (U-S and Fe-S, respectively) at environmentally relevant solution chemistry conditions (1–100 mM KCl and 0.1–10 mM CaCl2 at pH 7.0). Our results indicate that, in line with the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory, increasing influent ionic strength (IS) resulted in the reduced mobility of GONPs; and the impact of monovalent K+ was less than divalent Ca2+ in weakening the mobility of GONPs in both U-S and Fe-S. The positively charged iron oxide coating on the sand surface strongly immobilized the negatively charged GONPs at pH 7.0, producing the hyperexponential retention profiles for GONPs particularly in the presence of CaCl2 due primarily to the synergistic effects between iron oxide coating and Ca2+ (e.g., aggravate physical straining). A stepwise decreasing in pore-water transient IS initiated detachment of GONPs that were previously retained in the

Multisurface modeling of Ni bioavailability to wheat (Triticum aestivum L.) in various soils.

PubMed

Zhao, Xiaopeng; Jiang, Yang; Gu, Xueyuan; Gu, Cheng; Taylor, J Anita; Evans, Les J

2018-07-01

Continual efforts have been made to determine a simple and universal method of estimating heavy metal phytoavailability in terrestrial systems. In the present study, a mechanism-based multi-surface model (MSM) was developed to predict the partition of Ni(II) in soil-solution phases and its bioaccumulation in wheat (Triticum aestivum L.) in 19 Chinese soils with a wide range of soil properties. MSM successfully predicted the Ni(II) dissolution in 0.01 M CaCl 2 extracting solution (R 2  = 0.875). The two-site model for clay fraction improved the prediction, particularly for alkaline soils, because of the additional consideration of edge sites. More crucially, the calculated dissolved Ni(II) was highly correlated with the metal accumulation in wheat (R 2  = 0.820 for roots and 0.817 for shoots). The correlation coefficients for the MSM and various chemical extraction methods have the following order: soil pore water > MSM ≈ diffuse gradient technique (DGT) > soil total Ni > 0.43 M HNO 3  > 0.01 M CaCl 2 . The results suggested that the dissolved Ni(II) calculated using MSM can serve as an effective indicator of the bioavailability of Ni(II) in various soils; hence, MSM can be used as an supplement for metal risk prediction and assessment besides chemical extraction techniques. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of experimental variables onto Co(2+) and Sr(2+) sorption behavior in red mud-water suspensions.

PubMed

Milenković, Aleksandra S; Smičiklas, Ivana D; Šljivić-Ivanović, Marija Z; Živković, Ljiljana S; Vukelić, Nikola S

2016-07-02

The prospects of rinsed red mud (alumina production residue) utilization for liquid radioactive waste treatment have been investigated, with Co(2+) and Sr(2+) as model cations of radioactive elements. To evaluate the sorption effectiveness and corresponding binding mechanisms, the process was analyzed in batch conditions, by varying experimental conditions (pH, Co(2+) and Sr(2+) concentrations in single solutions and binary mixtures, contact time, and the concentration of competing cations and ligands common in liquid radioactive waste). Comparison of the Co(2+) and Sr(2+) sorption pH edges with the red mud isoelectric point has revealed that Co(2+) removal took place at both positive and negative red mud surface, while Sr(2+) sorption abruptly increased when the surface became negatively charged. The increase of initial cation content and pH resulted in increased equilibrium times and sorption capacity and decreased rate constants. From single metal solutions and various binary mixtures, Co(2+) was sorbed more efficiently and selectively than Sr(2+). While Sr(2+) sorption was reduced by coexisting cations in the order Al(3+) ≥ Ca(2+) >Na(+) ≥Cs(+), removal of Co(2+) was affected by Al(3+) species and complexing agents (EDTA and citrate). Desorption of Co(2+) was negligible in Ca(2+) and Sr(2+) containing media and in solutions with initial pH 4-7. Sr(2+) desorption was generally more pronounced, especially at low pH and in the presence of Co(2+). Collected macroscopic data signify that Co(2+) sorption by red mud minerals occurred via strong chemical bonds, while Sr(2+) was retained mainly by weaker ion-exchange or electrostatic interactions. Results indicate that the rinsed red mud represent an efficient, low-cost sorbent for Co(2+) and Sr(2+) immobilization.

[A PhD completed. Prevention and treatment of periodontal diseases and bad breath].

PubMed

van der Sluijs, E; Slot, D E; van der Weijden, G A

2018-01-01

Rinsing the mouth with water, or brushing with a dry toothbrush, does not contribute to an improvement in plaque removal during toothbrushing, nor does brushing according to a specific brushing regimen. Rinsing with water or drinking water has an immediate effect on bad morning breath. The combination of toothbrushing, tongue cleaning and a mouthwash has an effect on bad morning breath after 24 hours, in contrast with brushing with toothpaste only. The use of mouthwash with the specific ingredients chlorhexidine and essential oils has a positive effect on the reduction of gingivitis. The use of similar mouthwashes as a cooling solution in an ultrasonic device has no added effect on treatment results among periodontal patients. Water is an effective cooling solution.

ADSORPTION OF ORGANIC CATIONS TO NATURAL MATERIALS

EPA Science Inventory

The factors that control the extent of adsorption of amphiphilic organic cations on environmental and pristine surfaces have been studied. The sorbents were kaolinite, montmorillonite, two aquifer materials, and a soil; solutions contained various concentrations of NaCl and CaCl,...

Biochemical basis of improvement of defense in tomato plant against Fusarium wilt by CaCl2.

PubMed

Chakraborty, Nilanjan; Chandra, Swarnendu; Acharya, Krishnendu

2017-07-01

The objective of this study was to investigate the effectiveness of calcium chloride (CaCl 2 ), as potential elicitor, on tomato plants against Fusarium oxysporum f. sp. lycopersici . Foliar application of CaCl 2 showed significant reduction of wilt incidence after challenge inoculation. Increased production of defense and antioxidant enzymes was observed in elicitor treated sets over control. Simultaneously, altered amount of phenolic acids were analyzed spectrophotometrically and by using high performance liquid chromatography. Significant induction of defense-related genes expressions was measured by semi-quantitative RT-PCR. Greater lignifications by microscopic analysis were also recorded in elicitor treated plants. Simultaneously, generation of nitric oxide (NO) in elicitor treated plants was confirmed by spectrophotometrically and microscopically by using membrane permeable fluorescent dye. Furthermore, plants treated with potential NO donor and NO modulators showed significant alteration of all those aforesaid defense molecules. Transcript analysis of nitrate reductase and calmodulin gene showed positive correlation with elicitor treatment. Furthermore, CaCl 2 treatment showed greater seedling vigor index, mean trichome density etc. The result suggests that CaCl 2 have tremendous potential to elicit defense responses as well as plant growth in co-relation with NO, which ultimately leads to resistance against the wilt pathogen.

The long-term effect of a zinc acetate and chlorhexidine diacetate containing mouth rinse on intra-oral halitosis-A randomized clinical trial.

PubMed

Erovic Ademovski, Seida; Mårtensson, Carina; Persson, Gösta Rutger; Renvert, Stefan

2017-10-01

To evaluate the long-term effects of a zinc acetate and chlorhexidine diacetate mouth rinse (Zn/CHX) on intra-oral halitosis. Forty-six adults with intra-oral halitosis were randomized into a 6-month, double-blind, placebo-controlled clinical study. The presence of intra-oral halitosis was evaluated at baseline, 3 and 6 months after treatment by assessment of organoleptic score (OLS) and by total volatile sulphur compounds (T-VSC), hydrogen sulphide (H 2 S) and methyl mercaptan (MM) concentrations in exhaled air. A Zn/CHX mouth rinse provided significantly better control of intra-oral halitosis than a placebo mouth rinse. At 3 and 6 months, individuals rinsing with the Zn/CHX rinse presented with reductions of the OLS, T-VSC (p < .01, respectively), H 2 S (p < .001), and MM (p < .01) in subjects' exhaled air. At 6 months, 68.2% of individuals using the Zn/CHX rinse experienced a 1 or 2 category improvement in OLS compared with 19.1% of placebo-treated subjects. 91% of subjects in the Zn/CHX group were categorized as being effectively treated for intra-oral halitosis (i.e. H 2 S < 112 ppb), compared to 43% in the placebo group. Zn/CHX mouth rinse provides effective long-term efficacy against intra-oral halitosis, assessed both objectively and subjectively. With regular rinsing, the effect was sustained for 6 months. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Spasmolytic effect of Petroselinum crispum (Parsley) on rat's ileum at different calcium chloride concentrations.

PubMed

Moazedi, A A; Mirzaie, D N; Seyyednejad, S M; Zadkarami, M R; Amirzargar, A

2007-11-15

Traditional herbal medicines such as Petroselinum crispum (Parsley) have been used for treatment of intestinal disorders in Iran. To date no pharmacological evidence for their effectiveness has been reported. The aim of this study was to examine the relaxant effect of hydroalcoholic extract of Petroselinum crispum on isolated adult male Wistar rat's ileum contraction by KCl 60 (mM). The extract was prepared from parsley seed with 80% ethanol. A portion of ileum was removed and placed in an organ bath containing Tyrode solution (37 degrees C, pH = 7.4) bubbled with air. From a resting tension of 1 g, isotonic Transducer and Harvard Universal Oscillograph were used for recording contraction of ileum after administration of 60 mM KCl. Various concentration of extract were added to the bath. This experiment showed that, the extract in a dose-dependent manner decreased the induced-KCl ileums contraction (n = 7, p < 0.001). Also adding extract before influence of KCl, cause reduced effect of KCl (n = 7, p < 0.001). In addition, the Tyrode solution without CaCl2 and high concentration of K+, various concentration of extract significantly (n = 7, p < 0.001) decreased the CaCl2-induced contraction. Therefore, it seems that the relaxation effect of extract alcoholic parsley seed on the contraction of ileum is performed by blocking of voltage-gated calcium channels.

The rectification of mono- and bivalent ions in single conical nanopores

NASA Astrophysics Data System (ADS)

Wei, Junzhe; Du, Guanghua; Guo, Jinlong; Li, Yaning; Liu, Wenjing; Yao, Huijun; Zhao, Jing; Wu, Ruqun; Chen, Hao; Ponomarov, Artem

2017-08-01

The polyethylene terephthalate (PET) films were irradiated with single 6.9 MeV/u 58Ni19+ ions at the Lanzhou Interdisciplinary Heavy Ion Microbeam (LIHIM), and single conical nanopores were produced by asymmetric chemical etching of the latent ion tracks. Then, the current-voltage (I-V) characteristic was measured in LiCl, NaCl, KCl, MgCl2, and CaCl2 solution at different concentrations to study the transport properties of different cations in the single conical nanopores respectively. The measured I-V data showed that the conical nanopores have rectified transportation of these cations at the applied voltage of between +2 V and -2 V. The rectification coefficient γ of the mono- and bivalent ions was determined in their solution of 0.0001-1 M measured at 1 V, the result showed that the rectification coefficient is dependent on the valence of the ions and the electrolyte solution.

Removal of biofilm from contact lens storage cases.

PubMed

Wu, Yvonne T; Zhu, Hua; Willcox, Mark; Stapleton, Fiona

2010-12-01

Lens case hygiene practices are important in maintaining safe contact lens wear. However, the effectiveness of various lens case cleaning practices have not been evaluated and compared. This in vitro study aimed to evaluate and compare the efficacy of cleaning practices that are most commonly carried out by lens wearers and recommended by practitioners. Pseudomonas aeruginosa 122, Serratia marcescens ATCC 13880, and Staphylococcus aureus ATCC 6538 were the challenge bacteria for biofilm formation on unused lens cases from two different manufacturers. After establishment of the biofilm, each lens case was subjected to one of the six cleaning regimens: "rinsed," "rubbed and rinsed," "air-dried," "soaked in a multipurpose contact lens solution," "tissue-wiped," and "lids recapped." The level of residual biofilm was quantified at the end of each cleaning regimen. The efficacy of each cleaning regimen was then compared. Mechanical rubbing and wiping of lens cases were the most effective cleaning regimen tested in reducing biofilm. Soaking lenses in disinfecting solution for 6 hours removed the majority of biofilm from lens cases. Rinsing lens cases alone provided only minimal efficacy in reducing biofilm. Air-drying or recapping the cases with the lid without any other additional cleaning methods were the least efficient at removing biofilm. Based on this study, digital rubbing and rinsing and/or wiping the lens cases with tissue is recommended. Air-drying or recapping the lens case lids after use without any additional cleaning methods should be discouraged with non-antimicrobial lens cases.

Studies on transport phenomena in electrothermal vaporization sample introduction applied to inductively coupled plasma for optical emission and mass spectrometry

NASA Astrophysics Data System (ADS)

Kántor, T.; Maestre, S.; de Loos-Vollebregt, M. T. C.

2005-10-01

In the present work electrothermal vaporization (ETV) was used in both inductively coupled plasma mass spectrometry (ICP-MS) and optical emission spectrometry (OES) for sample introduction of solution samples. The effect of (Pd + Mg)-nitrate modifier and CaCl 2 matrix/modifier of variable amounts were studied on ETV-ICP-MS signals of Cr, Cu, Fe, Mn and Pb and on ETV-ICP-OES signals of Ag, Cd, Co, Cu, Fe, Ga, Mn and Zn. With the use of matrix-free standard solutions the analytical curves were bent to the signal axes (as expected from earlier studies), which was observed in the 20-800 pg mass range by ICP-MS and in the 1-50 ng mass range by ICP-OES detection. The degree of curvature was, however, different with the use of single element and multi-element standards. When applying the noted chemical modifiers (aerosol carriers) in microgram amounts, linear analytical curves were found in the nearly two orders of magnitude mass ranges. Changes of the CaCl 2 matrix concentration (loaded amount of 2-10 μg Ca) resulted in less than 5% changes in MS signals of 5 elements (each below 1 ng) and OES signals of 22 analytes (each below 15 ng). Exceptions were Pb (ICP-MS) and Cd (ICP-OES), where the sensitivity increase by Pd + Mg modifier was much larger compared to other elements studied. The general conclusions suggest that quantitative analysis with the use of ETV sample introduction requires matrix matching or matrix replacement by appropriate chemical modifier to the specific concentration ranges of analytes. This is a similar requirement to that claimed also by the most commonly used pneumatic nebulization of solutions, if samples with high matrix concentration are concerned.

Fermentation in nutrient salt mixtures affects green Spanish-style Manzanilla table olive characteristics.

PubMed

López-López, Antonio; Bautista-Gallego, Joaquín; Moreno-Baquero, José María; Garrido-Fernández, Antonio

2016-11-15

This work studies the effects of the substitution of NaCl with KCl and CaCl2 on the physicochemical, mineral and sensory profile of fermented green Spanish-style Manzanilla olives, using an enlarged centroid mixture design. An increasing presence of CaCl2 in the initial brines improved the colour index, L(∗), b(∗) values, and firmness. The Na in the olives decreased (linearly) while the levels of K and Ca increased (quadratic) as a function of the KCl and CaCl2 concentrations in the initial brines. CaCl2 also improved the retention of Zn and P in the flesh. PLS showed a strong relationship between Ca and bitterness, hardness, fibrousness, crunchiness and saltiness (negative) and allowed for the prediction of sensory attributes (except acid) from the mineral contents in the flesh. Most of the treatments could lead to new green Spanish-style Manzanilla olive presentations with reduced Na and healthier characteristics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Injection order effects on efficacy of calcium chloride and sodium tripolyphosphate in controlling the pink color defect in uncured, intact turkey breast.

PubMed

Claus, James R; Sawyer, Christopher A; Vogel, Kurt D

2010-04-01

An experiment was conducted to test sequential injection of sodium tripolyphosphate (STP; 0.5% meat weight basis, mwb) followed by injection with or without addition of calcium chloride (CaCl(2), 500 ppm mwb), and to test the effect of post-injection delay prior to cooking. A second experiment evaluated the impact of injection order and delay time between independent addition of CaCl(2) (500 ppm mwb) and STP (0.5% mwb). Turkey was formulated without an added pink generating ligand (NONE), with nicotinamide (NIC; 0.1% mwb), or with sodium nitrite (NIT; 10 ppm mwb). A white colloid was observed in the extracellular space of treatments containing both STP and CaCl(2.) Addition of CaCl(2) decreased nitrosylhemochrome but did not reduce levels of nicotinamide hemochrome or CIE a(*) values. Injection order or delay between injections did not contribute to controlling the pink defect in cooked, intact turkey breast. Published by Elsevier Ltd.

Is there a potential consumer market for low-sodium fermented sausages?

PubMed

Dos Santos, Bibiana A; Campagnol, Paulo C B; da Cruz, Adriano G; Morgano, Marcelo A; Wagner, Roger; Pollonio, Marise A R

2015-05-01

The NaCl levels in dry fermented sausages were reduced by 50% or were substituted with KCl, CaCl2 , or a blend of KCl and CaCl2 (1:1). The quality, safety, and the potential consumer market of dry fermented sausages were assessed. Neither 50% reduction of the NaCl content nor the substitution of 50% of the NaCl with KCl influenced the fermentation and maturation process. However, when CaCl2 was used as the substitute salt (50%), there was a significant decrease in pH, an increase in the water activity, and a decrease in lactic acid and micrococcus bacterial counts. Overall, the sensory acceptance decreased in dry fermented sausages with reduced sodium content. However, cluster analysis and internal preference mapping revealed potential for commercialization of samples with 50% of the NaCl content substituted with KCl or with a mixture of KCl and CaCl2 (1:1). © 2015 Institute of Food Technologists®

Sodium fluoride mouthrinse used twice daily increased incipient caries lesion remineralization in an in situ model.

PubMed

Songsiripradubboon, Siriporn; Hamba, Hidenori; Trairatvorakul, Chutima; Tagami, Junji

2014-03-01

To investigate the remineralizing effects of fluoride mouthrinses used at different times and frequency in addition to fluoride toothpaste. A randomized crossover single blinded study comprised 4 experimental phases of 21 days each. Twelve orthodontic volunteers were fixed with an orthodontic bracket containing an artificial carious enamel slab, which was from the same tooth in all 4 phases, and were randomly assigned to the following groups: (1) brushing with F toothpaste 2× per day (F- brush), (2) F- brush+rinsing with 0.05% NaF (F- rinse) after lunch, (3) F- brush+F-rinse before bedtime, and (4) F- brush+F- rinse 2× per day. Mean mineral gain after each phase was determined from mineral density profiles obtained using Micro-CT. The mean mineral gain in all treatments with F- brush and F-rinse were significantly greater than those in F- brush (p<0.05). Moreover F- rinse 2× per day increased lesion remineralization more than F- rinse once a day. The twice-daily use of 0.05% NaF mouthrinse combined with twice-daily regular use of fluoride toothpaste resulted in the greatest remineralization of incipient caries. These data indicate that rinsing frequency is a factor affecting the effectiveness of fluoride mouthrinse. The rinsing frequency of NaF mouthrinse, when used with fluoride toothpaste, also affects the remineralization. This finding, if confirmed by a clinical study, would lead to a new recommendation for fluoride mouthrinse used in high caries risk patients who could benefit from using it twice a day. Copyright © 2014 Elsevier Ltd. All rights reserved.

Physical properties of cobia (Rachycentron canadum) surimi: effect of washing cycle at different salt concentrations.

PubMed

Hamzah, N; Sarbon, N M; Amin, A M

2015-08-01

This study aimed to determine the effects of 2-5 wash cycles and the addition of tetrasodium pyrophosphate (TSPP) (0 %, 0.05 Surimi% and 0.1 % w/w)-with or without the addition of 0.4 % calcium chloride (CaCl2)-on the physical properties such as texture, colour, expressible moisture and microstructure of Cobia (Rachycentron canadum) surimi gel. The highest breaking force (484.85 g) was obtained with the addition 0.1 % TSPP alone on the fifth wash. However, a combination of 0.1 and 0.4 % CaCl2 in surimi gels at wash cycle 5 resulted in the highest degree of whiteness (86.8 %), as well as total expressible moisture (2.785 %) and deformation (17.11 mm). The highest surimi gel strength (6,923 g.mm) was obtained after three wash cycles with the addition of 0.1 % TSPP +0.4 % CaCl2. The physical properties of Cobia fish surimi gels were affected by the number of wash cycles and treatments with TSPP and CaCl2.

An induced current method for measuring zeta potential of electrolyte solution-air interface.

PubMed

Song, Yongxin; Zhao, Kai; Wang, Junsheng; Wu, Xudong; Pan, Xinxiang; Sun, Yeqing; Li, Dongqing

2014-02-15

This paper reports a novel and very simple method for measuring the zeta potential of electrolyte solution-air interface. When a measuring electrode contacts the electrolyte solution-air interface, an electrical current will be generated due to the potential difference between the electrode-air surface and the electrolyte solution-air interface. The amplitude of the measured electric signal is linearly proportional to this potential difference; and depends only on the zeta potential at the electrolyte solution-air interface, regardless of the types and concentrations of the electrolyte. A correlation between the zeta potential and the measured voltage signal is obtained based on the experimental data. Using this equation, the zeta potential of any electrolyte solution-air interface can be evaluated quickly and easily by inserting an electrode through the electrolyte solution-air interface and measuring the electrical signal amplitude. This method was verified by comparing the obtained results of NaCl, MgCl2 and CaCl2 solutions of different pH values and concentrations with the zeta potential data reported in the published journal papers. Copyright © 2013 Elsevier Inc. All rights reserved.

A Comparison of Aerosolization and Homogenization Techniques for Production of Alginate Microparticles for Delivery of Corticosteroids to the Colon.

PubMed

Samak, Yassmin O; El Massik, Magda; Coombes, Allan G A

2017-01-01

Alginate microparticles incorporating hydrocortisone hemisuccinate were produced by aerosolization and homogenization methods to investigate their potential for colonic drug delivery. Microparticle stabilization was achieved by CaCl 2 crosslinking solution (0.5 M and 1 M), and drug loading was accomplished by diffusion into blank microparticles or by direct encapsulation. Homogenization method produced smaller microparticles (45-50 μm), compared to aerosolization (65-90 μm). High drug loadings (40% wt/wt) were obtained for diffusion-loaded aerosolized microparticles. Aerosolized microparticles suppressed drug release in simulated gastric fluid (SGF) and simulated intestinal fluid (SIF) prior to drug release in simulated colonic fluid (SCF) to a higher extent than homogenized microparticles. Microparticles prepared using aerosolization or homogenization (1 M CaCl 2 , diffusion loaded) released 5% and 17% of drug content after 2 h in SGF and 4 h in SIF, respectively, and 75% after 12 h in SCF. Thus, aerosolization and homogenization techniques show potential for producing alginate microparticles for colonic drug delivery in the treatment of inflammatory bowel disease. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Effect of CaCl2 on the property of an anionic surfactant monolayer formed at the air/water interface: a molecular dynamics study

NASA Astrophysics Data System (ADS)

Zhang, Tiantian; You, Jing; Yu, Jiliang; Fan, Chengcheng; Ma, Yunfei; Cui, Yanjie; Gao, Shanshan; Li, Yongbin; Hu, Songqing; Liu, Huiqin

2017-12-01

Molecular dynamics simulation had been carried out to investigate the influence of CaCl2 on the aggregation behaviour of sodium dodecyl polyoxyethylene sulfonate (A12E2SO3) at the air/water interface. First, structure properties of A12E2SO3 monolayer was studied by analyzing the snapshots of the configuration and density profiles of different components in A12E2SO3 systems. Results showed that Ca2+ could replace some Na+ to combine with the hydrophilic headgroups. Besides, the addition of CaCl2 could reduce the thickness of water layer at the interface. Second, the interactions between A12E2SO3 headgroups and water molecules were studied through calculating radial distribution functions (RDFs) between water molecules and the sulfonate group, as well as the oxyethyl group. Results revealed that Ca2+ could penetrate the hydration layer of the sulfonate group, but could not enter the first hydration layer of the oxygen ethyl group close to the sulfonate group. The addition of CaCl2 could make the degree of hydration more orderly and the thickness of hydration layer in the headgroups of A12E2SO3 molecules increase. Third, the property of interface double layer was studied through analyzing RDFs of the headgroups and counterions. Results showed that the addition of CaCl2 could not only reduce the interaction between the headgroups and the counterions, but also compress the thickness of the electric double layer in A12E2SO3 system.

Characterization of superabsorbent hydrogel based on epichlorohydrin crosslink and carboxymethyl functionalization of cassava starch

NASA Astrophysics Data System (ADS)

Muharam, S.; Yuningsih, L. M.; Sumitra, M. R.

2017-07-01

Superabsorbent hydrogel was prepared by epichlorohydrin crosslink of cassava starch. Their swelling improved with added carboxymethyl group on the starch-epichlorohydrin structure. The structure and properties of starch-epichlorohydrin-carboxymethyl hydrogel were measured by SEM, FTIR, water and physiological solution absorption test and water retention test. The result showed that hydrogel displayed macroporous with heterogenous distribution and irregular surface was formed by epichlorohydrin and carboxymethyl bond in the structure of hydrogel. It was confirmed also by the FTIR spectra. The swelling ratio of starch-epichlorohydrin hydrogel to the water is 518 % and increased to 1,028.5 % with carboxymethyl addition on the structure. The best influence of the physiological solution to the swelling ratio of starch-epichlorohydrin-carboxymethyl hydrogel is urea solution. The water retention of starch-epichlorohydrin-carboxymethyl hydrogel in NaCl solution is better than in CaCl2 solution.

Effect of Green Coffee Bean Extract on Streptococcus mutans Count: A Randomised Control Trial

PubMed Central

Kaushik, Mamta; Roshni, Roshni; Reddy, Pallavi; Mehra, Neha; Jain, Vallari; Rana, Ritu

2017-01-01

Introduction Mouth rinses have been popularly used as a supplementary oral hygiene aid. A lot of commercially available mouth rinses possess few adverse effects, which has necessitated the search for alternative and herbal mouth rinses. Aim The aim of the study was to assess the effect of rinsing with green coffee bean extract in comparison with chlorhexidine mouthwash and sterile water on salivary Streptococcus mutans count. Materials and Methods A randomized parallel controlled clinical trial was planned and 45 subjects aged between 18-22 years were selected. The subjects were divided into three groups (n=15 in each group): Group A: Study group: 2% Green coffee bean extract, Group B: Positive control: 0.2% Chlorhexidine (CHX), Group C: Negative control: Sterile water. Group A subjects rinsed mouth with 5 ml of 2% Green coffee bean extract for one minute. Group B subjects rinsed mouth with 5 ml 0.2% CHX mouthwash for one minute. Group C subjects rinsed mouth with 5 ml of Sterile water for one minute twice daily for two weeks. Baseline samples (Pre rinse) were collected on day 1 and post rinsing saliva samples were collected after 14 days. The samples were cultured using Mitis Salivarius Agar enriched with Bacitracin and colonies were counted using a hand held digital colony counter. The statistical analysis was done using paired t-test, One-way variance ANOVA and Post-Hoc tests. Results The Green coffee bean extract group showed a statistical significant reduction in Streptococcus mutans colony count before and after intervention which was comparable with CHX group. Conclusion Green coffee bean extract as a mouthwash can be explored as a safe and effective alternative to CHX mouthwash. PMID:28658911

Roles of Cationic and Elemental Calcium in the Electro-Reduction of Solid Metal Oxides in Molten Calcium Chloride

NASA Astrophysics Data System (ADS)

Qiu, Guohong; Jiang, Kai; Ma, Meng; Wang, Dihua; Jin, Xianbo; Chen, George Z.

2007-06-01

Previous work, mainly from this research group, is re-visited on electrochemical reduction of solid metal oxides, in the form of compacted powder, in molten CaCl2, aiming at further understanding of the roles of cationic and elemental calcium. The discussion focuses on six aspects: 1.) debate on two mechanisms proposed in the literature, i. e. electro-metallothermic reduction and electro-reduction (or electro-deoxidation), for the electrolytic removal of oxygen from solid metals or metal oxides in molten CaCl2; 2.) novel metallic cavity working electrodes for electrochemical investigations of compacted metal oxide powders in high temperature molten salts assisted by a quartz sealed Ag/AgCl reference electrode (650 ºC- 950 ºC); 3.) influence of elemental calcium on the background current observed during electrolysis of solid metal oxides in molten CaCl2; 4.) electrochemical insertion/ inclusion of cationic calcium into solid metal oxides; 5.) typical features of cyclic voltammetry and chronoamperometry (potentiostatic electrolysis) of metal oxide powders in molten CaCl2; and 6.) some kinetic considerations on the electrolytic removal of oxygen.

Water Evaporation from Acoustically Levitated Aqueous Solution Droplets.

PubMed

Combe, Nicole A; Donaldson, D James

2017-09-28

We present a systematic study of the effect of solutes on the evaporation rate of acoustically levitated aqueous solution droplets by suspending individual droplets in a zero-relative humidity environment and measuring their size as a function of time. The ratios of the early time evaporation rates of six simple salts (NaCl, NaBr, NaNO 3 , KCl, MgCl 2 , CaCl 2 ) and malonic acid to that of water are in excellent agreement with predictions made by modifying the Maxwell equation to include the time-dependent water activity of the evaporating aqueous salt solution droplets. However, the early time evaporation rates of three ammonium salt solutions (NH 4 Cl, NH 4 NO 3 , (NH 4 ) 2 SO 4 ) are not significantly different from the evaporation rate of pure water. This finding is in accord with a previous report that ammonium sulfate does not depress the evaporation rate of its solutions, despite reducing its water vapor pressure, perhaps due to specific surface effects. At longer evaporation times, as the droplets approach crystallization, all but one (MgCl 2 ) of the solution evaporation rates are well described by the modified Maxwell equation.

21 CFR 184.1193 - Calcium chloride.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Calcium chloride. 184.1193 Section 184.1193 Food... Specific Substances Affirmed as GRAS § 184.1193 Calcium chloride. (a) Calcium chloride (CaCl2·2H2O, CAS Reg. No. 10035-04-8) or anhydrous calcium chloride (CaCl2, CAS Reg. No. 10043-52-4) may be commercially...

21 CFR 184.1193 - Calcium chloride.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Calcium chloride. 184.1193 Section 184.1193 Food... Specific Substances Affirmed as GRAS § 184.1193 Calcium chloride. (a) Calcium chloride (CaCl2·2H2O, CAS Reg. No. 10035-04-8) or anhydrous calcium chloride (CaCl2, CAS Reg. No. 10043-52-4) may be commercially...

21 CFR 184.1193 - Calcium chloride.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium chloride. 184.1193 Section 184.1193 Food... GRAS § 184.1193 Calcium chloride. (a) Calcium chloride (CaCl2·2H2O, CAS Reg. No. 10035-04-8) or anhydrous calcium chloride (CaCl2, CAS Reg. No. 10043-52-4) may be commercially obtained as a byproduct in...

Structural elucidation and estimation of the acute toxicity of the major UV-visible photoproduct of fludioxonil - detection in both skin and flesh samples of grape.

PubMed

Lassalle, Yannick; Nicol, Édith; Genty, Christophe; Bourcier, Sophie; Bouchonnet, Stéphane

2015-06-01

Ultraviolet (UV)-visible irradiation of fludioxonil was investigated with two photoreactors using either a mercury or xenon vapor lamp. In both cases, it led to the formation of only one photoproduct in significant amount: 2-(2,2-difluorobenzo[d][1,3]dioxol-4-yl)-2-(nitrosomethylene)-4-oxobutanenitrile, which has been characterized using Liquid Chromatography - High Resolution - Tandem Mass Spectrometry (LC-HR-MS/MS) coupling. A photolysis pathway has been proposed to rationalize its formation in degassed water. In vitro bioassays on Vibrio fischeri bacteria showed that UV-vis irradiation of an aqueous solution of fludioxonil significantly increases its toxicity. Because no other by-product was detected in significant amount, the photoproduct mentioned above may be considered mainly responsible for this increase in toxicity. Grape berries treated with a 50 ppm aqueous solution of fludioxonil were submitted to UV-visible irradiation under laboratory conditions. The fungicide and photoproduct were detected in both skin and flesh of berries, even after they have been rinsed with water. The ability of the photoproduct to pass through the fruit skin is comparable with that of fludioxonil. These results are of concern for consumers because they mean that water tap rinsing does not lead to efficient removing of both compounds. Copyright © 2015 John Wiley & Sons, Ltd.

Efficacy of neutral electrolyzed water to inactivate Escherichia coli, Listeria monocytogenes, Pseudomonas aeruginosa, and Staphylococcus aureus on plastic and wooden kitchen cutting boards.

PubMed

Deza, M A; Araujo, M; Garrido, M J

2007-01-01

This study evaluated the efficacy of neutral electrolyzed water (NEW; 64.1 mg/liter of active chlorine) to reduce populations of Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus, and Listeria monocytogenes on plastic and wooden kitchen cutting boards. Its effectiveness was compared with that of a sodium hypochlorite solution (NaClO; 62.3 mg/liter of active chlorine). Inoculated portions of cutting boards were rinsed in either NEW or NaClO solutions, or deionized water (control). Plastic boards were rinsed for 1 min and wooden boards for 1 and 5 min. After each treatment, the surviving population of each strain was determined on the surface and in the soaking water. No significant difference (P > or = 0.05) was found between the final populations of each strain with regard to the treatment solutions (NEW or NaClO). However, a significant difference (P < or = 0.05) was revealed between surface materials after 1 min of washing. Whereas in plastic boards the initial bacterial populations were reduced by 5 log CFU/50 cm2, in wooden cutting boards they underwent a reduction of <3 log CFU/50 cm2. A 5-min exposure time yielded reductions of about 4 log CFU/50 cm2. The surviving populations of all bacteria in NEW and NaCIO washing solutions were <1 log CFU/ml after soaking both surfaces. This study revealed that NEW treatment is an effective method for reducing microbial contamination on plastic and wooden cutting boards. NEW efficacy was comparable to that of NaCIO, with the advantage of having a larger storage time.

An in vitro evaluation of a novel high fluoride daily mouthrinse using a combination of microindentation, 3D profilometry and DSIMS.

PubMed

Gracia, Louise H; Rees, Gareth D; Brown, Alan; Fowler, Christabel E

2010-11-01

Firstly, to evaluate the in vitro anti-erosion efficacy of a new mouthrinse formulation containing 450 ppm fluoride using profilometry and microindentation. Secondly, to compare fluoride uptake by erosive lesions from two mouthrinses containing different fluoride sources using dynamic secondary ion mass spectrometry (DSIMS). Sound human enamel was treated (60s) with mouthrinses containing different fluoride concentrations, then immersed in 1.0% citric acid pH 3.8 for either 300 s or 30 min (Studies 1 & 2 respectively). Surface roughness and erosion depth were determined profilometrically in Study 1, and surface microhardness monitored as a function of time in Study 2. Lesion rehardening was monitored following a 60 s rinse and immersion in artificial saliva for 48 h (Study 3), whilst Study 4 employed DSIMS to quantify fluoride uptake by lesions treated (60s) with rinses containing either sodium fluoride (NaF) or a NaF/Olaflur/stannous chloride combination. The test rinse (450 ppm fluoride) suppressed surface roughening and bulk tissue loss versus all comparators (p< 0.0001), except in the latter measure for the rinse containing 112 ppm fluoride. The test rinse significantly inhibited enamel surface softening versus the three rinses containing ≤112 ppm fluoride (as NaF) at 30 min (p<0.05), but was not statistically significantly different from the 225 ppm fluoride rinse. The test rinse conferred statistically superior lesion rehardening versus all comparators at both 24 and 48 h (p< 0.0001). DSIMS demonstrated statistically significantly higher fluoride uptake by incipient erosive lesions treated with the test rinse versus the NaF/Olaflur/stannous rinse. Anti-erosion efficacy was positively correlated with fluoride concentration. DSIMS showed significantly higher levels of fluoride uptake by incipient erosive lesions treated with the 450 ppm fluoride rinse versus the NaF/Olaflur/stannous rinse. Copyright © 2010 Elsevier Ltd. All rights reserved.

Selective Removal of Iron from Low-Grade Ti Ore by Reacting with Calcium Chloride

NASA Astrophysics Data System (ADS)

Kang, Jungshin; Okabe, Toru H.

2017-02-01

Recently, titanium metal production by molten salt electrolysis using CaCl2 as molten salt and TiO2 or rutile (94 to 96 pct TiO2) as feedstock has been drawing attention. However, when a low-grade Ti ore (mainly FeTiO3) is used as feedstock, removal of iron (Fe) from the ore is indispensable. In this study, the influence of reaction temperature, reaction time, particle size of the ore, and source country for the ore on the removal of iron by selective chlorination using CaCl2 was assessed. Experimental results showed that the mass percent of iron in the ore decreased from 49.7 to 1.79 pct under certain conditions by selective removal of iron as FeCl2. As a result, high-grade CaTiO3 was produced when the ore particles smaller than 74 µm reacted with CaCl2 at 1240 K (967 °C) for 8 to 10 hours. Therefore, this study demonstrates that the removal of iron from the ore is feasible through the selective chlorination process using CaCl2 by optimizing the variables.

Effects of NaCl and CaCl2 on Water Transport across Root Cells of Maize (Zea mays L.) Seedlings 1

PubMed Central

Azaizeh, Hassan; Gunse, Benito; Steudle, Ernst

1992-01-01

The effect of salinity and calcium levels on water flows and on hydraulic parameters of individual cortical cells of excised roots of young maize (Zea mays L. cv Halamish) plants have been measured using the cell pressure probe. Maize seedlings were grown in one-third strength Hoagland solution modified by additions of NaCl and/or extra calcium so that the seedlings received one of four treatments: control; +100 millimolar NaCl; +10 millimolar CaCl2; +100 millimolar NaCl + 10 millimolar CaCl2. From the hydrostatic and osmotic relaxations of turgor, the hydraulic conductivity (Lp) and the reflection coefficient (σs) of cortical cells of different root layers were determined. Mean Lp values in the different layers (first to third, fourth to sixth, seventh to ninth) of the four different treatments ranged from 11.8 to 14.5 (Control), 2.5 to 3.8 (+NaCl), 6.9 to 8.7 (+CaCl2), and 6.6 to 7.2 · 10−7 meter per second per megapascal (+NaCl + CaCl2). These results indicate that salinization of the growth media at regular calcium levels (0.5 millimolar) decreased Lp significantly (three to six times). The addition of extra calcium (10 millimolar) to the salinized media produced compensating effects. Mean cell σs values of NaCl ranged from 1.08 to 1.16, 1.15 to 1.22, 0.94 to 1.00, and 1.32 to 1.46 in different root cell layers of the four different treatments, respectively. Some of these σs values were probably overestimated due to an underestimation of the elastic modulus of cells, σs values of close to unity were in line with the fact that root cell membranes were practically not permeable to NaCl. However, the root cylinder exhibited some permeability to NaCl as was demonstrated by the root pressure probe measurements that resulted in σsr of less than unity. Compared with the controls, salinity and calcium increased the root cell diameter. Salinized seedlings grown at regular calcium levels resulted in shorter cell length compared with control (by a factor of 2). The results demonstrate that NaCl has adverse effects on water transport parameters of root cells. Extra calcium could, in part, compensate for these effects. The data suggest a considerable apoplasmic water flow in the root cortex. However, the cell-to-cell path also contributed to the overall water transport in maize roots and appeared to be responsible for the decrease in root hydraulic conductivity reported earlier (Azaizeh H, Steudle E [1991] Plant Physiol 97: 1136-1145). Accordingly, the effect of high salinity on the cell Lp was much larger than that on root Lpr. PMID:16669016

Effect of calcium chloride on physical properties of calcium-enriched mixture cement.

PubMed

Abbaszadegan, Abbas; Sedigh Shams, Mahdi; Jamshidi, Yasin; Parashos, Peter; Bagheri, Rafat

2015-12-01

The aim of this study was to evaluate the effect of adding 10% calcium chloride (CaCl2) on the setting time, solubility and the pH of calcium-enriched mixture (CEM) cement. Setting time was assessed in accordance with American Dental Association specification N°57. Solubility was measured at 24 and 72 h, 7 and 14 days in hydrated and dehydrated conditions by calculating weight change. The pH of MiliQ water in which the CEM cement samples were immersed was measured immediately after each time interval with and without the addition of CaCl2. The data were analysed using the Mann-Whitney U-test and the Student's t-test. The initial setting time was significantly decreased after the addition of 10% CaCl2. The pH of water increased immediately when in contact with the cements in both groups. The weight loss of hydrated and dehydrated specimens was more than 3% and was significantly reduced by the addition of 10% CaCl2. © 2015 Australian Society of Endodontology.

The effectiveness of propolis on gingivitis: a randomized controlled trial.

PubMed

Bretz, Walter A; Paulino, Niraldo; Nör, Jacques E; Moreira, Alexandre

2014-12-01

A randomized, double-blind, controlled clinical trial was conducted to evaluate the effectiveness of a propolis rinse on induced gingivitis by using the co-twin study design. Twenty-one twin pairs (n=42) were enrolled in a gingivitis study with oral hygiene promotion (14 days) and gingivitis induction (21 days). During the gingivitis induction phase, one member of the twin pair was randomly assigned to a 2% typified propolis rinse, and the other was assigned a color-matched 0.05% sodium fluoride plus 0.05% cetylpyridinium chloride rinse (positive control). Patients rinsed twice daily with 20 mL for 30 seconds for 21 days. Gingivitis was measured on days -14 (baseline), 0 (after hygiene phase), and 21 (after no-hygiene phase) by using the Papillary Bleeding Score (PBS) and by standard digital imaging of the gum tissues (G-parameter). The 38 persons who completed the study (age 13-22 years) were well balanced according to PBS at baseline and G-parameter after the initial hygiene phase. After 21 days without oral hygiene, the propolis rinse and positive control rinse groups did not differ significantly for average PBS measurements or G-parameter. Use of a 2% typified propolis rinse was equivalent to a positive control rinse during a 21-day no-hygiene period.

A Diffusive Gradient-in-Thin-Film Technique for Evaluation of the Bioavailability of Cd in Soil Contaminated with Cd and Pb

PubMed Central

Wang, Peifang; Wang, Teng; Yao, Yu; Wang, Chao; Liu, Cui; Yuan, Ye

2016-01-01

Management of heavy metal contamination requires accurate information about the distribution of bioavailable fractions, and about exchange between the solid and solution phases. In this study, we employed diffusive gradients in thin-films (DGT) and traditional chemical extraction methods (soil solution, HOAc, EDTA, CaCl2, and NaOAc) to determine the Cd bioavailability in Cd-contaminated soil with the addition of Pb. Two typical terrestrial species (wheat, Bainong AK58; maize, Zhengdan 958) were selected as the accumulation plants. The results showed that the added Pb may enhance the efficiency of Cd phytoextraction which is indicated by the increasing concentration of Cd accumulating in the plant tissues. The DGT-measured Cd concentrations and all the selected traditional extractants measured Cd concentrations all increased with increasing concentration of the addition Pb which were similar to the change trends of the accumulated Cd concentrations in plant tissues. Moreover, the Pearson regression coefficients between the different indicators obtained Cd concentrations and plants uptake Cd concentrations were further indicated significant correlations (p < 0.01). However, the values of Pearson regression coefficients showed the merits of DGT, CaCl2, and Csol over the other three methods. Consequently, the in situ measurement of DGT and the ex situ traditional methods could all reflect the inhibition effects between Cd and Pb. Due to the feature of dynamic measurements of DGT, it could be a robust tool to predict Cd bioavaiability in complex contaminated soil. PMID:27271644

The effect of carbohydrate mouth rinse on performance, biochemical and psychophysiological variables during a cycling time trial: a crossover randomized trial.

PubMed

Ferreira, Amanda M J; Farias-Junior, Luiz F; Mota, Thaynan A A; Elsangedy, Hassan M; Marcadenti, Aline; Lemos, Telma M A M; Okano, Alexandre H; Fayh, Ana P T

2018-01-01

The hypothesis of the central effect of carbohydrate mouth rinse (CMR) on performance improvement in a fed state has not been established, and its psychophysiological responses have not yet been described. The aim of this study was to evaluate the effect of CMR in athletes fed state on performance, biochemical and psychophysiological responses compared to ad libitum water intake. Eleven trained male cyclists completed a randomized, crossover trial, which consisted of a 30 km cycle ergometer at self-selected intensity and in a fed state. Subjects were under random influence of the following interventions: CMR with a 6% unflavored maltodextrin solution; mouth rinsing with a placebo solution (PMR); drinking "ad libitum" (DAL). The time for completion of the test (min), heart rate (bpm) and power (watts), rating of perceived exertion (RPE), affective response, blood glucose (mg/dL) and lactate (mmol/DL), were evaluated before, during and immediately after the test, while insulin (uIL/mL), cortisol (μg/dL) and creatine kinase (U/L) levels were measured before, immediately after the test and 30 min after the test. Time for completion of the 30 km trial did not differ significantly among CMR, PMR and DAL interventions (means = 54.5 ± 2.9, 54.7 ± 2.9 and 54.5 ± 2.5 min, respectively; p  = 0.82). RPE and affective response were higher in DAL intervention ( p  < 0.01). Glucose, insulin, cortisol and creatine kinase responses showed no significant difference among interventions. In a fed state, CMR has not caused metabolic changes, and it has not improved physical performance compared to ad libitum water intake, but demonstrated a possible central effect. ReBec registration number: RBR-4vpwkg. Available in http://www.ensaiosclinicos.gov.br/rg/?q=RBR-4vpwkg.

Microencapsulation of bioactive principles with an airless spray-gun suitable for processing high viscous solutions.

PubMed

Cocchietto, Moreno; Blasi, Paolo; Lapasin, Romano; Moro, Chiara; Gallo, Davide; Sava, Gianni

2013-11-19

to design, assemble and test a prototype of a novel production plant, suitable for producing microparticles (MPs) by processing highly viscous feed solutions (FSs). the prototype has been built using a commercial air compressor, a piston pump, an airless spray-gun, a customized air-treatment section, a timer, a rotating base, and a filtration section. Preliminary prototype parameter setting was carried out to individuate the best performing nozzle's dimension, the nebulization timing, and the CaCl2 concentration in the gelation fluid. In addition, prototype throughput (1 L to 5 L) and the range of practicable feed solution (FS) viscosities were assayed. A set of four batches was prepared in order to characterize the MPs, in terms of mean particle size and distribution, flow properties, swelling, encapsulation efficiency and release. according to a qualitative scoring, the large nozzle was suitable to nebulize FSs at a higher alginate concentration. Conversely, the small nozzle performed better in the processing of FSs with an alginate concentration up to 2% w/v. Only at the highest degree of viscosity, corresponding to 5% w/v of alginate, the FS processing was not technically possible. Among the CaCl2 concentrations considered, 15% w/v was recognized as the most versatile. The prototype appears to be convenient and suitable to grant a high yield starting from 2 L of FS. The flow behavior of the FSs assayed can be satisfactorily described with the Carreau-Yasuda equation and the throughput begins to slightly decrease for FSs at alginate concentrations exceeding 3% w/v. MP morphology was irregular with crumpled shape. The angle of repose indicates a good flowability and the release studies showed gastro-resistance and potential prolonged release applications. the novel prototype of production plant is suitable to process large amounts (2 L or more) of FSs, characterized by a high viscosity, to produce MPs suitable for bioactive principle delivery.

Microencapsulation of Bioactive Principles with an Airless Spray-Gun Suitable for Processing High Viscous Solutions

PubMed Central

Cocchietto, Moreno; Blasi, Paolo; Lapasin, Romano; Moro, Chiara; Gallo, Davide; Sava, Gianni

2013-01-01

Purpose: to design, assemble and test a prototype of a novel production plant, suitable for producing microparticles (MPs) by processing highly viscous feed solutions (FSs). Methods: the prototype has been built using a commercial air compressor, a piston pump, an airless spray-gun, a customized air-treatment section, a timer, a rotating base, and a filtration section. Preliminary prototype parameter setting was carried out to individuate the best performing nozzle’s dimension, the nebulization timing, and the CaCl2 concentration in the gelation fluid. In addition, prototype throughput (1 L to 5 L) and the range of practicable feed solution (FS) viscosities were assayed. A set of four batches was prepared in order to characterize the MPs, in terms of mean particle size and distribution, flow properties, swelling, encapsulation efficiency and release. Results: according to a qualitative scoring, the large nozzle was suitable to nebulize FSs at a higher alginate concentration. Conversely, the small nozzle performed better in the processing of FSs with an alginate concentration up to 2% w/v. Only at the highest degree of viscosity, corresponding to 5% w/v of alginate, the FS processing was not technically possible. Among the CaCl2 concentrations considered, 15% w/v was recognized as the most versatile. The prototype appears to be convenient and suitable to grant a high yield starting from 2 L of FS. The flow behavior of the FSs assayed can be satisfactorily described with the Carreau-Yasuda equation and the throughput begins to slightly decrease for FSs at alginate concentrations exceeding 3% w/v. MP morphology was irregular with crumpled shape. The angle of repose indicates a good flowability and the release studies showed gastro-resistance and potential prolonged release applications. Conclusions: the novel prototype of production plant is suitable to process large amounts (2 L or more) of FSs, characterized by a high viscosity, to produce MPs suitable for bioactive principle delivery. PMID:24956192

Comparative proteomic and metabolomic analyses reveal mechanisms of improved cold stress tolerance in bermudagrass (Cynodon dactylon (L.) Pers.) by exogenous calcium.

PubMed

Shi, Haitao; Ye, Tiantian; Zhong, Bao; Liu, Xun; Chan, Zhulong

2014-11-01

As an important second messenger, calcium is involved in plant cold stress response, including chilling (<20 °C) and freezing (<0 °C). In this study, exogenous application of calcium chloride (CaCl2 ) improved both chilling and freezing stress tolerances, while ethylene glycol-bis-(β-aminoethyl) ether-N,N,N,N-tetraacetic acid (EGTA) reversed CaCl2 effects in bermudagrass (Cynodon dactylon (L.) Pers.). Physiological analyses showed that CaCl2 treatment alleviated the reactive oxygen species (ROS) burst and cell damage triggered by chilling stress, via activating antioxidant enzymes, non-enzymatic glutathione antioxidant pool, while EGTA treatment had the opposite effects. Additionally, comparative proteomic analysis identified 51 differentially expressed proteins that were enriched in redox, tricarboxylicacid cycle, glycolysis, photosynthesis, oxidative pentose phosphate pathway, and amino acid metabolisms. Consistently, 42 metabolites including amino acids, organic acids, sugars, and sugar alcohols were regulated by CaCl2 treatment under control and cold stress conditions, further confirming the common modulation of CaCl2 treatment in carbon metabolites and amino acid metabolism. Taken together, this study reported first evidence of the essential and protective roles of endogenous and exogenous calcium in bermudagrass response to cold stress, partially via activation of the antioxidants and modulation of several differentially expressed proteins and metabolic homeostasis in the process of cold acclimation. © 2014 Institute of Botany, Chinese Academy of Sciences.

Influence of calcium-induced droplet heteroaggregation on the physicochemical properties of oppositely charged lactoferrin coated lutein droplets and whey protein isolate-coated DHA droplets.

PubMed

Li, Xin; Wang, Xu; Xu, Duoxia; Cao, Yanping; Wang, Shaojia; Wang, Bei; Wang, Chengtao; Sun, Baoguo

2017-08-01

The influence of calcium-induced droplet heteroaggregation on the formation and physicochemical stability of mixed lutein and DHA emulsions was studied. Heteroaggregation was induced by mixing oppositely charged lactoferrin (LF)-coated lutein and whey protein isolate (WPI)-coated DHA emulsions with different CaCl 2 concentrations at pH 6.0. The droplet size, zeta-potential, transmission-physical stability and microstructure behavior (CLSM and Cryo-SEM) of single-protein emulsions and mixed emulsions were measured as a function of different CaCl 2 concentrations. Lutein degradation and DHA oxidation by measurement of lipid hydroperoxides and thiobarbituric acid reactive substances were determined during storage. The physical stability of the mixed emulsions could be modulated by controlling CaCl 2 concentrations. Microstructure behavior indicated that a mixed emulsion with 30 mM CaCl 2 promoted more droplets to form a special three-dimensional network and microcluster structures. The chemical stability of the mixed lutein and DHA emulsions was obviously enhanced by the addition of 30 mM CaCl 2 . The decreased surface areas of the DHA and lutein droplets and the physical barrier of the network of heteroaggregates against transition metals and free radicals could mainly explain the improvement in chemical stability. Calcium-induced droplet aggregation may be useful for creating specific food structures that lead to desirable physicochemical properties of multiple functional components.

Effectiveness of chamomile (Matricaria recutita L.), MTAD and sodium hypochlorite irrigants on smear layer.

PubMed

Venkataram, V; Gokhale, S T; Kenchappa, M; Nagarajappa, R

2013-08-01

Endodontic success depends heavily on effective chemo-mechanical debridement of root canals through the use of instruments and irrigating solutions. To compare the effectiveness of chamomile hydroalcoholic extract, Biopure™ mixture of tetracycline isomer, acid and detergent (MTAD) and 2.5 % sodium hypochlorite (NaOCl) on removal of the smear layer. Randomised controlled trial. Thirty extracted single-rooted, primary human teeth were allocated at random into three experimental groups of 10 teeth each. For each tooth, the canal was prepared using the step-back technique. During instrumentation, 2 ml of the irrigant was used for at least 10 s after each file and 10 ml as a final flush for 2 min for chamomile and NaOCL irrigants. Whereas for MTAD, an initial rinse with 1.3 % NaOCl for a cumulated period of 20 min, and use of MTAD as the final rinse for a period of 5 min was followed. Longitudinal grooves were made on root segments, then split into two halves with a chisel, stored in 2.5 % glutaraldehyde solution and fixed in ethanol series. Specimens were examined for the smear layer according to Hulsmann et al. (Int Endod J 35:668-679, 2002) criteria using a scanning electron microscope. Kruskal-Wallis and Mann-Whitney U tests were used. The most effective result in removal of smear layer occurred with the use of MTAD, followed by chamomile extract. The chamomile extract was found to be significantly more effective than 2.5 % NaOCl solution which had only minor effects. The efficacy of chamomile to remove the smear layer was superior to 2.5 % NaOCl alone, but less effective than MTAD mixture.

Selective separation of phosphate and fluoride from semiconductor wastewater.

PubMed

Warmadewanthi, B; Liu, J C

2009-01-01

Hydrofluoric acid (HF) and phosphoric acid (H(3)PO(4)) are widely used in semiconductor industry for etching and rinsing purposes. Consequently, significant amount of wastewater containing phosphate and fluoride is generated. Selective separation of phosphate and fluoride from the semiconductor wastewater, containing 936 mg/L of fluoride, 118 mg/L of phosphate, 640 mg/L of sulfate, and 26.7 mg/L of ammonia, was studied. Chemical precipitation and flotation reactions were utilized in the two-stage treatment processes. The first-stage reaction involved the addition of magnesium chloride (MgCl(2)) to induce selective precipitation of magnesium phosphate. The optimal condition was pH 10 and molar ratio, [Mg(2 + )]/[(PO(4) (3-))], of 3:1, and 66.2% of phosphate was removed and recovered as bobierrite (Mg(3)(PO(4))(2).8H(2)O). No reaction was found between MgCl(2) and fluoride. Calcium chloride (CaCl(2)) was used in the second-stage reaction to induce precipitation of calcium fluoride and calcium phosphate. The optimum molar ratio, [Ca(2 + )]/[F(-)], was 0.7 at pH 10, and residual fluoride concentration of 10.7 mg/L and phosphate concentration of lower than 0.5 mg/L was obtained. Thermodynamic equilibrium was modeled with PHREEQC and compared with experimental results. Sodium dodecylsulfate (SDS) was an effective collector for subsequent solid-liquid removal via dispersed air flotation (DiAF). The study demonstrated that phosphate can be selectively recovered from the wastewater. Potential benefits include recovery of phosphate for reuse, lower required dosage of calcium for fluoride removal, and less amount of CaF(2) sludge.

The influence of salivary variables on fluoride retention in dental plaque exposed to a mineral-enriching solution.

PubMed

Kato, K; Nakagaki, H; Arai, K; Pearce, E I F

2002-01-01

This study was carried out to examine interindividual differences in salivary variables related to plaque accumulation and to estimate their influence on the fluoride retention in plaque in vivo by a mineral-enriching solution. Two saliva samples were taken from 10 subjects, once after brushing and once after 24 h without brushing. Calcium, phosphate and monofluorophosphatase (MFPase) activity in the saliva samples were determined. The salivary flow rate and the debris index were also recorded. After plaque had formed over 3 days within in situ plaque-generating devices, subjects were instructed to rinse with a mineral-enriching mouthrinse three times a day on 4 consecutive days. Plaque exposed to distilled water plus flavoring agents served as a control. Fluoride-free dentifrice was used during the experimental period. Twenty-four hours after the last rinsing, the samples were removed from the mouth, and fluoride and mineral distributions in plaque analyzed using a method previously reported by the authors. Salivary flow, MFPase activity and calcium concentration in saliva were significantly higher after 24 h of plaque accumulation. Rinsing with the mineral-enriching solution produced retention of fluoride and phosphate in the outer and middle layers of plaque. Salivary calcium concentration had a direct effect on fluoride uptake in plaque, but no obvious relationship was found between other salivary variables and the plaque fluoride retention. The salivary calcium effect may be due to enhanced bacterial cell wall binding of fluoride via calcium bridging. Copyright 2002 S. Karger AG, Basel

Chloroxyanion Residue on Seeds and Sprouts after Chlorine Dioxide Sanitation of Alfalfa Seed.

PubMed

Smith, David J; Herges, Grant R

2018-02-28

The effects of a 6-h chlorine dioxide sanitation of alfalfa seed (0, 50, 100, and 200 mg/kg seed) on total coliform bacteria, seed germination, and the presence of chlorate and perchlorate residues in seed rinse, seed soak, and alfalfa sprouts was determined. Chlorate residues in 20,000 mg/L calcium hypochlorite, commonly used to disinfect seed, were quantified. Chlorine dioxide treatment reduced (P < 0.05) total coliforms on seeds with no effect (P > 0.05) on germination. Dose-dependent sodium chlorate residues were present in seed rinse (4.1 to 31.2 μg/g seed) and soak (0.7 to 8.3 μg/g seed) waters, whereas chlorate residues were absent (LOQ 5 ng/g) in sprouts, except for 2 of 5 replicates from the high chlorine dioxide treatment. Copious chlorate residues were present (168 to 1260 mg/L) in freshly prepared 20,000 mg/L calcium hypochlorite solution, and storage at room temperature increased chlorate residues significantly (P < 0.01).

Monetite formed in mixed solvents of water and ethylene glycol and its transformation to hydroxyapatite.

PubMed

Ma, Ming-Guo; Zhu, Ying-Jie; Chang, Jiang

2006-07-27

Agglomerated nanorods of hydroxyapatite have been synthesized using monetite as a precursor in a NaOH solution. Monetite consisting of nanosheets has been successfully synthesized by a one-step microwave-assisted method using CaCl(2).2.5H(2)O, NaH(2)PO(4), and sodium dodecyl sulfate (SDS) in water/ethylene glycol (EG) mixed solvents. The effects of the molar ratio of water to EG and the reaction time on the products were investigated. The products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infrared spectrometry (FTIR).

Effects of a Novel Whitening Formulation on Dental Enamel.

PubMed

Takesh, Thair; Sargsyan, Anik; Anbarani, Afarin; Ho, Jessica; Wilder-Smith, Petra

2017-04-01

The goal of this study was to evaluate the enamel whitening effects of 2 new test formulations, one of which was a rinse, and the other a whitening strip. Forty enamel chips were prepared from 20 healthy extracted teeth (2 from each tooth). After pre-staining and colorimetry to measure L* and b* values, 20 matched samples were immersed in either test or control rinses, and then colorimetry was performed again after 1 hr, 2 hr, 3 hr, 6 hr, 12 hr, 24 hr and 48 hrs (Each hour equates to one month of clinical use at the recommended dosage of 1 minute exposure 2 times a day). The remaining 20 matched samples were exposed to the test or control whitening strips and colorimetry was performed every 30 minutes for a total of 10 treatments. Overall, the whitening performance of test and control strips was similar. The test and control rinses had a similar lightening effect over the first 3 hours (equivalent to 3 months of clinical use). Subsequently, the control rinse continued to lighten samples, whereas the test rinse had little further effect. Test and control-whitening strips showed similar effects; over time whitening strips showed a greater lightening effect than whitening rinses.

A clinical trial of the effect of a mouth-rinse prepared with Lippia sidoides Cham essential oil in dogs with mild gingival disease.

PubMed

Girão, V C C; Nunes-Pinheiro, D C S; Morais, S M; Sequeira, J L; Gioso, M A

2003-05-30

We evaluated the effect of a mouth-rinse prepared using Lippia sidoides essential oil (EO) in dogs with marginal gingivitis. German Shepherd dogs were distributed in two groups: control (control mouth-rinse) and EO (EO mouth-rinse). Both mouth-rinses were applied on the dogs' teeth every 2 days for 2 weeks. At day 0 and day 15, the scores for plaque-bacteria (P), calculus (C), gingivitis (G) and the inflammatory infiltrate (INF) were evaluated blindly. The results were analyzed by the Wilcoxon signed-rank and Mann-Whitney tests (P

Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

NASA Astrophysics Data System (ADS)

Johnson, P. V.; Thomas, E. C.; Hodyss, R. P.; Vu, T. H.; Choukroun, M.

2016-12-01

Understanding the habitability of Europa's ocean is of great interest to astrobiology and is the focus of missions currently being considered to explore Europa. Currently, our best means of constraining the subsurface ocean composition and its subsequent habitability is by further study of Europa's surface chemical composition. Analysis of existing (and future) remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Geochemical predictions of Europa's ocean composition suggest that chloride salts are likely to exist on the surface of Europa as well as other ocean worlds. We have conducted a study of frozen chloride-salt brines prepared at temperatures, pressures and radiation conditions (UV) in order to simulate conditions on the surface of Europa and other airless bodies. Hydration states of various chloride salts as a function of temperature were determined using Raman spectroscopy. Near IR reflectance spectra of identically prepared samples were measured to provide reference spectra of the identified hydrated salts. We find that the freezing of NaCl at temperatures ranging from 80 K to 233 K forms hydrohalite. In contrast, KCl hydrates are not formed from the freezing of KCl brines. In addition, a stable hexahydrate forms from the freezing of MgCl2 solutions, while a hexahydrate, a tetrahydrate, and a dihydrate, form upon freezing of CaCl2 solutions. Salts were observed to dehydrated with increasing temperatures, leading to a succession of hydration states in the case of CaCl2. Irradiation with vacuum ultraviolet light was observed to lead to dehydration as well.

Surface complexation of carboxylate adheres Cryptosporidium parvum öocysts to the hematite-water interface

USGS Publications Warehouse

Gao, X.; Metge, D.W.; Ray, C.; Harvey, R.W.; Chorover, J.

2009-01-01

The interaction of viable Cryptosporidium parvum öocysts at the hematite (α-Fe2O3)−water interface was examined over a wide range in solution chemistry using in situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. Spectra for hematite-sorbed öocysts showed distinct changes in carboxylate group vibrations relative to spectra obtained in the absence of hematite, indicative of direct chemical bonding between carboxylate groups and Fe metal centers of the hematite surface. The data also indicate that complexation modes vary with solution chemistry. In NaCl solution, öocysts are bound to hematite via monodentate and binuclear bidentate complexes. The former predominates at low pH, whereas the latter becomes increasingly prevalent with increasing pH. In a CaCl2 solution, only binuclear bidentate complexes are observed. When solution pH is above the point of zero net proton charge (PZNPC) of hematite, öocyst surface carboxylate groups are bound to the mineral surface via outer-sphere complexes in both electrolyte solutions.

Impact of rice-straw biochars amended soil on the biological Si cycle in soil-plant ecosystem

NASA Astrophysics Data System (ADS)

Li, Zimin; Delvaux, Bruno; Struyf, Eric; Unzué-Belmonte, Dácil; Ronsse, Frederik; Cornelis, Jean-Thomas

2017-04-01

Biochar used as soil amendment can enhance soil fertility and plant growth. It may also contribute to increase the plant mineralomass of silicon (Si). However, very little studies have focused on the plant Si cycling in biochar amended soils. Here, we study the impact of two contrasting biochars derived from rice straws on soil Si availability and plant Si uptake. Rice plants were grown in a hydroponic device using Yoshida nutrient solution, respectively devoid of H4SiO4 (0 ppm Si: Si-) and enriched with it (40 ppm Si: Si+). After 12 weeks, the plants were harvested for further pyrolysis, conducted with holding time of 1h at 500˚ C. The respective rice-biochars are Si-/biochar and Si+/biochar. They exhibit contrasting phytolith contents (0.3 g Si kg-1 vs. 51.3 g Si kg-1), but identical physico-chemical properties. They were applied in two soils differing in weathering stage: a weathered Cambisol (CA) and a highly weathered Nitisol (NI). We then studied the effects of the amended biochar on CaCl2 extractable Si using a 64-days kinetic approach, on the content of soil biogenic Si, and on the uptake of Si by wheat plants grown for 5 weeks. We also quantified Si mineralomass in plants. We compared the effects of biochars to that of wollastonite (Wo)-(CaSiO3), a common Si-fertilizer. Our results show that Si+/biochar significantly increase the content of BSi in both soils. In CA, the cumulative content of CaCl2 extractable Si amounts to 85 mg kg-1 after Si+/biochar amendment, which is below the amount extracted after Wo application (100 mg kg-1). In contrast, in NI, the cumulative content of CaCl2 extractable Si is 198 mg kg-1 in the Si+/biochar amended treatment, which is far above the one measured after Wo application (93 mg kg-1). The Si-/biochar has no effect on the cumulative content of CaCl2 extractable Si in either soil type. Biochars and wollastonite increase the biomass of wheat on both soils. The increase is, however, larger in NI than in CA. In terms of Si uptake by wheat , Si-/biochar does not increase the Si content of plants in either soil type. As expected, Si+/biochar and wollastonite significantly increase the Si content of wheat plants grown on both soils. The increase caused by Si+/biochar is, larger in NI (10 mg Si pot-1) than that in CA (5 mg Si pot-1). This result is in line with the release of CaCl2 extractable Si in both soils amended by Si+/biochar, confirming the validity of CaCl2-extraction to estimate the pool of bioavailable Si. Our data highlight that phytolith-rich biochar readily contributes to the pool of bioavailable Si, further taken up by plant roots, and increases Si mineralomass in plants as well as plant growth. Thus it provides an alternative to wollastonite application. The effect is particularly large in the highly weathered Nitisol. Under such conditions, the impact of phytolith rich biochar is not limited to the enhancement of Si biological cycle, but is extended to the increase of soil pH, CEC and organic matter content.

Stability of self-assembled polymer films investigated by optical laser reflectometry.

PubMed

Dejeu, Jérôme; Diziain, Séverine; Dange, Catherine; Membrey, François; Charraut, Daniel; Foissy, Alain

2008-04-01

We studied the influence of post-treatment rinsing after the formation of self-assembled polyelectrolyte films made with the weak base poly(allylamine hydrochloride) (PAH) and the strong acid poly(styrene sulfonate) (PSS). The stability of the film was studied using optical fixed-angle laser reflectometry to measure the release of polymeric material and AFM experiments to reveal the change of morphology and thickness. We found that the polymer films were stable upon rinsing when the pH was the same in the solution as that used in the buildup (pH 9). The films released most of the polymeric material when rinsed at higher pH values, but a layer remained that corresponded to a PAH monolayer directly bound with the silica surface. Films containing at least four bilayers were stable upon rinsing at lower pH values, but the stability of thinner films depended on the type of the last polymer deposited. They were stable in the case of PSS as an outermost deposit, but they released a large part of their material in the case of PAH. The stability results were determined using a simple model of the step-by-step assembly of the polymer film described formerly.

Evaluation of microbeads of calcium alginate as a fluidized bed medium for affinity chromatography of Aspergillus niger Pectinase.

PubMed

Roy, Ipsita; Jain, Sulakshana; Teotia, Sunita; Gupta, Munishwar Nath

2004-01-01

Calcium alginate microbeads (212-425 microm) were prepared by spraying 2% (w/v) alginate solution into 1 M CaCl2 solution. The fluidization behavior of these beads was studied, and the bed expansion index and terminal velocity were found to be 4.3 and 1808 cm h(-1), respectively. Residence time distribution curves showed that the dispersion of the protein was much less with these microbeads than with conventionally prepared calcium alginate macrobeads when both kinds of beads were used for chromatography in a fluidized bed format. The fluidized bed of these beads was used for the purification of pectinase from a commercial preparation. The media performed well even with diluted feedstock; 90% activity recovery with 211-fold purification was observed.

Agricultural land contamination by heavy metals around the former mining site of Bechateur (northern Tunisia)

NASA Astrophysics Data System (ADS)

Daldoul, G.; Soussi, R.; Soussi, F.; Boularbah, A.

2012-04-01

The activity of the former Pb-Zn mine of Jebel Ghozlen (Béchateur. extreme northern Tunisia) generated during the last century large quantities of tailings (extraction, flotation, gravimetry) deposited as three heap between the mine site and the shoreline located 700 m away. Areas surrounding the mine site are agricultural and are crossed by two rivers, one of which crosses the main heap. The minerals that make up these wastes are calcite, dolomite, quartz, gypsum, pyrite, barite, smithsonite, cerussite and galena. The amounts of Zn, Cd and Pb in the wastes vary between 1.3 and 9.3%, 1.1% and 5.7 and 185 and 410 mg kg-1, respectively. Soils in the study area are carbonated and are characterized by a silt-sand texture. The clay fraction is dominated by kaolinite. The chemical analysis of thirty samples collected over an area of 3 km2 shows that the amounts of total organic carbon (TOC) and total sulfur vary from 0.7 % to 2.5 % and 0.08 % to 0.96 %, respectively, while those of Zn, Pb and Cd range from 300 to 22 000 mg kg-1, 85 to 3000 mg kg-1 and 2 to 47 mg kg-1, respectively. The highest concentrations of metals were found in flood plains at 500 m downstream of the mine site. Extraction tests using deionized water and a 0.1 M CaCl2 solution were performed to assess the mobility of Zn, Pb and Cd in contaminated and reference soil samples collected within the study area. The results of extraction with deionized water showed that the leached amounts of Zn and Cd range between 0.2 and 4 mg kg-1 and 0.02 and 0.2 mg kg-1, respectively; while that of Pb is quite near the detection limit. During the extraction with CaCl2 the leached amounts of Zn, Pb and Cd range from 0.3 to 86 mg kg-1, 2 to 6 mg kg-1 and 0.05 to 0.9 mg kg-1, respectively. Thus, the mobility of Cd, Zn and Pb in CaCl2 solution (0.8 %, 0.4 % and 0.3 %, respectively) is higher compared with the extraction with deionized water (0.2%, 0.1% and 0.02 %, respectively). Toxicity tests were conducted on these soils using the MetPlate method. The results show a low bioavailability of contaminants.

Effect of various rinsing protocols after use of amine fluoride/stannous fluoride toothpaste on the bacterial composition of dental plaque.

PubMed

van Loveren, C; Gerardu, V A M; Sissons, C H; van Bekkum, M; ten Cate, J M

2009-01-01

This clinical study evaluated the effect of different oral hygiene protocols on the bacterial composition of dental plaque. After a 2-week period of using fluoride-free toothpaste, 30 participants followed three 1-week experimental protocols, each followed by 2-week fluoride-free washout periods in a randomized crossover examiner-blind controlled trial. The 1-week experimental protocols comprised the use of AmF/SnF(2) toothpaste twice daily, after which participants either (1) rinsed with tap water, (2) did not rinse but only spat out the toothpaste, or (3) rinsed with an AmF/SnF(2) mouthwash. In the fluoride-free washout periods, the participants brushed their teeth with fluoride-free toothpaste without further instructions. Six hours after the last brushing (+/- rinsing) of each period, buccal plaque samples in the upper molar region were taken. The microbiota composition of the plaque samples was analyzed by checkerboard DNA:DNA hybridization. A statistically significant reduction was found in the total amount of DNA of the 39 major plaque species measured, and in the proportions of some acid-producing bacterial strains after the period having used the AmF/SnF(2) toothpaste + AmF/SnF(2) mouthrinsing. The results indicate that using the AmF/SnF(2) toothpaste and rinse combination could result in plaque of lower cariogenicity. Copyright 2009 S. Karger AG, Basel.

Raman study of CaDNA films as a function of water content and excess CaCl2 concentration: Stability of the B conformation.

NASA Astrophysics Data System (ADS)

Schwenker, Megan; Marlowe, Robert; Lee, Scott; Rupprecht, Allan

2006-03-01

Highly oriented, wet-spun films of CaDNA expand in the direction perpendicular to the helical axis as the hydration of the film is increased. CaDNA films with a high CaCl2 content show an unexpected shrinkage at a relative humidity of about 93%. We have performed Raman experiments on CaDNA films as a function of both water content and excess CaCl2 concentration in order to determine if this unexpected shrinkage might be related to a conformational transition of the DNA molecules. We find that the DNA molecules remain in the B conformation for all salt contents down to a relative humidity of 59%.

Exchangeable hydrogen explains the pH of spodosol Oa horizons

USGS Publications Warehouse

Ross, D.S.; David, M.B.; Lawrence, G.B.; Bartlett, R.J.

1996-01-01

The chemistry of extremely acid Oa horizons does not conform to traditional pH, Al, and base saturation relationships. Results from two separate studies of northeastern U.S. forested soils were used to investigate relationships between pH in water or dilute salt solutions and other soil characteristics. In Oa horizons with pH below 4, soil pH in dilute CaCl2 solution was correlated with exchangeable H+ measured either by titration (r = -0.88, P = 0.0001, n = 142) or by electrode (r = -0.89, P = 0.0001, n = 45). Exchangeable H+ expressed as a percentage of the cation-exchange capacity (CEC) was linear with pH and showed similar slopes for data from both studies. For all samples, pHw = 4.21 - 1.80 x H+/CEC (R2 = 0.69, n = 194). The reciprocal of the H+/CEC ratio is base saturation with Al added to the bases. Because of the low pH, exchangeable Al does not appear to behave as an acid. Exchangeable H+ remains an operationally defined quantity because of the difficulty in separating exchange and hydrolysis reactions. In a variety of neutral-salt extractants, concentration of H+ were correlated with 0.1 M BaCl2-exchangeable H+ (r > 0.91, P = 0.0001, n = 26) regardless of the strength of the extract. Nine successive extractions with 0.33 mM CaCl2 removed more H+ than was removed by single batch extractions with either 1 M KCl or 0.1 M BaCl2 (average H+ of 70, 43, and 49 mmol kg-1, respectively for 26 samples). The data showed little difference in the chemical behavior of Oa horizons from a variety of geographical sites and vegetation types.

Comparison of ultrasonic-assisted and regular leaching of germanium from by-product of zinc metallurgy.

PubMed

Zhang, Libo; Guo, Wenqian; Peng, Jinhui; Li, Jing; Lin, Guo; Yu, Xia

2016-07-01

A major source of germanium recovery and also the source of this research is the by-product of lead and zinc metallurgical process. The primary purpose of the research is to investigate the effects of ultrasonic assisted and regular methods on the leaching yield of germanium from roasted slag containing germanium. In the study, the HCl-CaCl2 mixed solution is adopted as the reacting system and the Ca(ClO)2 used as the oxidant. Through six single factor (leaching time, temperature, amount of Ca(ClO)2, acid concentration, concentration of CaCl2 solution, ultrasonic power) experiments and the comparison of the two methods, it is found the optimum collective of germanium for ultrasonic-assisted method is obtained at temperature 80 °C for a leaching duration of 40 min. The optimum concentration for hydrochloric acid, CaCl2 and oxidizing agent are identified to be 3.5 mol/L, 150 g/L and 58.33 g/L, respectively. In addition, 700 W is the best ultrasonic power and an over-high power is adverse in the leaching process. Under the optimum condition, the recovery of germanium could reach up to 92.7%. While, the optimum leaching condition for regular leaching method is same to ultrasonic-assisted method, except regular method consume 100 min and the leaching rate of Ge 88.35% is lower about 4.35%. All in all, the experiment manifests that the leaching time can be reduced by as much as 60% and the leaching rate of Ge can be increased by 3-5% with the application of ultrasonic tool, which is mainly thanks to the mechanical action of ultrasonic. Copyright © 2015 Elsevier B.V. All rights reserved.

Novel Strip Test for Circulating Hormones

DTIC Science & Technology

1996-10-01

estrone- 3 -glucuronide was combined with 1 equivalent of 4-amino-benzo-15-crown-5 and 1.2 equivalents of 1 -ethyl- 3 -( 3 - dimethylaminopropyl )carbodiimide...solution containing 5 mg/ml of El-g and 10 mg/ml of 1 -ethyl- 3 -( 3 -dimethylamino-propyl)carbodiimide (EDC) in water at pH 4.2. Fibers are then rinsed with... hydrochloride in water at pH 4.0. The mixture was stirred at room temperature for 48 hours and the resulting estrone- 3 -glucuronide-4-amino-benzo-15-crown

Minimising alkalinity and pH spikes from Portland cement-bound Bauxsol (seawater-neutralized red mud) pellets for pH circum-neutral waters.

PubMed

Despland, Laure M; Clark, Malcolm W; Aragno, Michel; Vancov, Tony

2010-03-15

Bauxsol reagents (powder, slurry, or pellet forms) are powerful tools in environmental remediation and water and sewage treatment However, when used in circum-neutral water treatments, cement-bound Bauxsol pellets produce a sustained pH and alkalinity spike due to the presence of unreacted CaO in the cement binder. This study developed a pellet treatment system to minimize the alkalinity/pH spike. The recipe for pelletization consisted of Bauxsol powder, ordinary Portland cement (OPC), hydrophilic fumed silica, aluminum powder, a viscosity modifier, and water. Several batches (including different ratios and sizes) were run using modified makeup waters (H(2)0 + CO(2) or NaHCO(3)) or curing brines (CO(2), NaHCO(3), or Mg/CaCl(2)). Alkalinity, pH stability, and slake durability tests were performed on pellets before and/or after curing. The best result for reducing the alkalinity/pH spike was obtained from a MgCl(2), CaCl(2) bath treatment using a Bauxsol:cement ratio of 2.8:1 (pH 8.28; alkalinity 75.1 mg/L) for a 100 g batch or 245:1 (pH 8.05; alkalinity 35.4 mg/L) for a 1 kg batch. Although brine curing does provide a control on pH/alkalinity release, the pellets may still contain unreacted CaO. Therefore, a freshwater rinse of pellets before treating circum-neutral waters is recommended as is the continued investigation of alternative pellet binders.

No calcium-fluoride-like deposits detected in plaque shortly after a sodium fluoride mouthrinse.

PubMed

Vogel, G L; Tenuta, L M A; Schumacher, G E; Chow, L C

2010-01-01

Plaque 'calcium-fluoride-like' (CaF(2)-like) and fluoride deposits held by biological/bacterial calcium fluoride (Ca-F) bonds appear to be the source of cariostatic concentrations of fluoride in plaque fluid. The aim of this study was to quantify the amounts of plaque fluoride held in these reservoirs after a sodium fluoride rinse. 30 and 60 min after a 228 microg/g fluoride rinse, plaque samples were collected from 11 volunteers. Each sample was homogenized, split into 2 aliquots (aliquots 1 and 2), centrifuged, and the recovered plaque fluid combined and analyzed using microelectrodes. The plaque mass from aliquot 1 was retained. The plaque mass from aliquot 2 was extracted several times with a solution having the same fluoride, calcium and pH as the plaque fluid in order to extract the plaque CaF(2)-like deposits. The total fluoride in both aliquots was then determined. In a second experiment, the extraction completeness was examined by applying the above procedure to in vitro precipitates containing known amounts of CaF(2)-like deposits. Nearly identical fluoride concentrations were found in both plaque aliquots. The extraction of the CaF(2)-like precipitates formed in vitro removed more than 80% of these deposits. The results suggest that either CaF(2)-like deposits were not formed in plaque or, if these deposits had been formed, they were rapidly lost. The inability to form persistent amounts of CaF(2)-like deposits in plaque may account for the relatively rapid loss of plaque fluid fluoride after the use of conventional fluoride dentifrices or rinses. (c) 2010 S. Karger AG, Basel.

No Calcium-Fluoride-Like Deposits Detected in Plaque Shortly after a Sodium Fluoride Mouthrinse

PubMed Central

Vogel, G.L.; Tenuta, L.M.A.; Schumacher, G.E.; Chow, L.C.

2010-01-01

Plaque ‘calcium-fluoride-like’ (CaF2-like) and fluoride deposits held by biological/bacterial calcium fluoride (Ca-F) bonds appear to be the source of cariostatic concentrations of fluoride in plaque fluid. The aim of this study was to quantify the amounts of plaque fluoride held in these reservoirs after a sodium fluoride rinse. 30 and 60 min after a 228 μg/g fluoride rinse, plaque samples were collected from 11 volunteers. Each sample was homogenized, split into 2 aliquots (aliquots 1 and 2), centrifuged, and the recovered plaque fluid combined and analyzed using microelectrodes. The plaque mass from aliquot 1 was retained. The plaque mass from aliquot 2 was extracted several times with a solution having the same fluoride, calcium and pH as the plaque fluid in order to extract the plaque CaF2-like deposits. The total fluoride in both aliquots was then determined. In a second experiment, the extraction completeness was examined by applying the above procedure to in vitro precipitates containing known amounts of CaF2-like deposits. Nearly identical fluoride concentrations were found in both plaque aliquots. The extraction of the CaF2-like precipitates formed in vitro removed more than 80% of these deposits. The results suggest that either CaF2-like deposits were not formed in plaque or, if these deposits had been formed, they were rapidly lost. The inability to form persistent amounts of CaF2-like deposits in plaque may account for the relatively rapid loss of plaque fluid fluoride after the use of conventional fluoride dentifrices or rinses. PMID:20185917

21 CFR 177.1980 - Vinyl chloride-propylene copolymers.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., catching the rinsings in the beaker, and the solution is acidified with concentrated nitric acid using methyl purple as an indicator. The beaker is covered with a watch glass, and the contents are boiled...

Water purification using organic salts

DOEpatents

Currier, Robert P.

2004-11-23

Water purification using organic salts. Feed water is mixed with at least one organic salt at a temperature sufficiently low to form organic salt hydrate crystals and brine. The crystals are separated from the brine, rinsed, and melted to form an aqueous solution of organic salt. Some of the water is removed from the aqueous organic salt solution. The purified water is collected, and the remaining more concentrated aqueous organic salt solution is reused.

Abiotic elicitors mediated elicitation of innate immunity in tomato: an ex vivo comparison.

PubMed

Chakraborty, Nilanjan; Ghosh, Sudeepa; Chandra, Swarnendu; Sengupta, Sarban; Acharya, Krishnendu

2016-07-01

Improvement of the host resistance by using hazard free chemical elicitors is emerging as an alternative approach in the field of plant disease management. In our present work, we have screened the efficacy and possible mechanism of abiogenic elicitors like Dipotassium hydrogen orthophosphate ( K 2 HPO 4 ), Oxalic acid (OA), Isonicotinic acid (INA), Salicylic acid (SA), Acetylsalicylate (AS), Arachidonic acid (AA) and Calcium chloride (CaCl 2 ) to stimulate innate immune responses in Lycopersicum esculentum Mill. Excised tomato leaves, treated with elicitors at three different concentrations, were found to stimulate defense and antioxidative enzymes, total phenol and flavonoid content after 24 h of incubation. CaCl 2 (0.5 %) followed by INA (2.5 mM) were found most effective in activation of all such defense molecules in tomato leaves. Furthermore, nitric oxide (NO), a key gaseous mediator in plant defense signaling, was also measured after subsequent elicitor application. Higher doses of elicitors showed an elevated level of reactive oxygen species (ROS) generation, enhanced lipid peroxidation rate and proline content, which indicates the extent of abiotic stress generation on the leaves. However, ROS production, lipid peroxidation rate and proline concentration remain significantly reduced as a result of CaCl 2 (0.5 %) and INA (2.5 mM) application. A sharp increase of total chlorophyll content was also recorded due to treatment of CaCl 2 (0.5 %). These results demonstrate the effects of different abiogenic elicitors to regulate the production of defense molecules. Results also suggest that among all such chemicals, CaCl 2 (0.5 %) and INA (2.5 mM) can be used as a potential elicitor in organic farming of tomato.

Viability of sublethally injured coliform bacteria on fresh-cut cabbage stored in high CO2 atmospheres following rinsing with electrolyzed water.

PubMed

Izumi, Hidemi; Inoue, Ayano

2018-02-02

The extent of sublethally injured coliform bacteria on shredded cabbage, either rinsed or not rinsed with electrolyzed water, was evaluated during storage in air and high CO 2 controlled atmospheres (5%, 10%, and 15%) at 5°C and 10°C using the thin agar layer (TAL) method. Sublethally injured coliform bacteria on nonrinsed shredded cabbage were either absent or they were injured at a 64-65% level when present. Rinsing of shredded cabbage with electrolyzed water containing 25ppm available chlorine reduced the coliform counts by 0.4 to 1.1 log and caused sublethal injury ranging from 42 to 77%. Pantoea ananatis was one of the species injured by chlorine stress. When shredded cabbage, nonrinsed or rinsed with electrolyzed water, was stored in air and high CO 2 atmospheres at 5°C for 7days and 10°C for 5days, coliform counts on TAL plates increased from 3.3-4.5 to 6.5-9.0 log CFU/g during storage, with the increase being greater at 10°C than at 5°C. High CO 2 of 10% and 15% reduced the bacterial growth on shredded cabbage during storage at 5°C. Although injured coliform bacteria were not found on nonrinsed shredded cabbage on the initial day, injured coliforms at a range of 49-84% were detected on samples stored in air and high CO 2 atmospheres at 5°C and 10°C. Injured cells were detected more frequently during storage at both temperatures irrespective of the CO 2 atmosphere when shredded cabbage was rinsed with electrolyzed water. These results indicated that injured coliform bacteria on shredded cabbage, either rinsed or not rinsed with electrolyzed water, exhibited different degrees of injury during storage regardless of the CO 2 atmosphere and temperature tested. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of Promoter Hypermethylation Pattern in Salivary Rinses Collected with and without an Exfoliating Brush from Patients with HNSCC

PubMed Central

Sun, Wenyue; Zaboli, David; Liu, Yan; Arnaoutakis, Demetri; Khan, Tanbir; Wang, Hao; Koch, Wayne; Khan, Zubair; Califano, Joseph A.

2012-01-01

Background Salivary rinses have been recently proposed as a valuable resource for the development of epigenetic biomarkers for detection and monitoring of head and neck squamous cell carcinoma (HNSCC). Both salivary rinses collected with and without an exfoliating brush from patients with HNSCC are used in detection of promoter hypermethylation, yet their correlation of promoter hypermethylation has not been evaluated. This study was to evaluate the concordance of promoter hypermethylation between salivary rinses collected with and without an exfoliating brush from patients with HNSCC. Methodolgy 57 paired salivary rinses collected with or without an exfoliating brush from identical HNSCC patients were evaluated for promoter hypermethylation status using Quantitative Methylation-Specific PCR. Target tumor suppressor gene promoter regions were selected based on our previous studies describing a panel for HNSCC screening and surveillance, including P16, CCNA1, DCC, TIMP3, MGMT, DAPK and MINT31. Principal Findings In salivary rinses collected with and without brush, frequent methylation was detected in P16 (8.8% vs. 5.2%), CCNA1 (26.3% vs. 22.8%), DCC (33.3% vs. 29.8%), TIMP3 (31.6% vs. 36.8%), MGMT (29.8% vs. 38.6%), DAPK (14.0% vs. 19.2%), and MINT31 (10.5% vs. 8.8%). Spearman's rank correlation coefficient showed a positive correlation between salivary rinses collected with and without brush for P16 (ρ = 0.79), CCNA1 (ρ = 0.61), DCC (ρ = 0.58), TIMP3 (ρ = 0.10), MGMT (ρ = 0.70), DAPK (ρ = 0.51) and MINT31 (ρ = 0.72) (P<0.01). The percent agreement of promoter methylation between salivary rinses with brush and without brush were 96.5% for P16, 82.5% for CCNA1, 78.9% for DCC, 59.7% for TIMP3, 84.2% for MGMT, 84.2% for DAPK, and 94.7% for MINT31. Conclusions Our study demonstrated strong correlations of gene promoter hypermethylation between salivary rinses collected with and without an exfoliating brush. Salivary rinse collection without using an exfoliating brush may offer a cost effective, rapid, non-invasive, and reliable means for development of epigenetic salivary rinse biomarkers. PMID:22438973

Discoloration of Provisional Restorations after Oral Rinses

PubMed Central

Turgut, Sedanur; Bagis, Bora; Ayaz, Elif Aydogan; Ulusoy, Kıvanç Utku; Altintas, Subutay Han; Korkmaz, Fatih Mehmet; Bagis, Nilsun

2013-01-01

Purpose: Oral rinses are widely used to promote periodontal health with provisional restorations during the interim period. The aim of this study was to compare the discoloration of provisional restoration materials with different oral rinses. Material and Methods: A total of 140 disc-shaped specimens (shade A2) (10 mm x 2 mm) were prepared from one PMMA-based (TemDent Classic®) and three different bis-acrylic-based (Protemp II®, Luxatemp® and Fill-In®) provisional restoration materials (n=7). The color values (L*, a*, and b*) of each specimen were measured before and after exposure with a colorimeter, and the color changes (∆E) were calculated according to the CIE L*a*b* system. The specimens were immersed in each of the 4 oral rinses (alcohol-containing mouthwash, chlorhexidine, benzydamine HCl, benzydamine HCl and chlorhexidine) twice a day for 2 minutes. After 2 minutes of immersion in the oral rinses, the specimens were immersed in artificial saliva. The specimens were exposed to the oral rinses and the artificial saliva for 3 weeks. Two-way ANOVA, the Bonferroni test and the paired sample t-test were used for statistical analyses (p<0.05). Results: Comparison of the discoloration from the oral rinses after immersion for three weeks revealed no significant differences (p>0.05). The lowest color change was observed in PMMA-based Temdent in all oral rinses (p<0.05). There were no significant differences between the bis-acryl composites after immersion in saliva or the mixture of benzydamine HCl and chlorhexidine and the alcohol-containing mouthwash for 3 weeks (p>0.05). After immersion in chlorhexidine, the color change values of Protemp II and Fill-in showed significant differences (p=0.018). Protemp II also showed less discoloration than the other bis-acryl composites, and this color change was statistically significant (p <0.05). For all oral rinses, the L* value decreased while b* values increased, and this color change was found to be statistically significant (p <0.05). A* values were found to be significantly higher with oral rinses (p<0.05), except Protemp II immersed in benzydamine HCl or alcohol-containing mouthwash. Conclusions: The type of the oral rinse did not affect the discoloration process. For long-term esthetic results, choosing MMA-based materials for provisional restorations appears to be more effective. PMID:24046524

Sorption of ionic and nonionic organic solutes onto giant Miscanthus-derived biochar from methanol-water mixtures.

PubMed

Kim, Juhee; Hyun, Seunghun

2018-02-15

The sorption of naphthalene (NAP) and 1-naphthoic acid (1-NAPA) onto giant Miscanthus-derived biochar was investigated in methanol volume fractions (f c ) of 0-0.6 as a function of ionic composition (5mM CaCl 2 and 10mM KCl) and liquid pH (2 and 7). The sorption onto biochar was nonlinear with 0.42≤N≤0.95; thus, a concentration-specific sorption constant (K m ) was compared. The K m log linearly decreased with increasing f c , except for 1-NAPA from a CaCl 2 mixture at pH7. Isotherm data was fitted with a cosolvency sorption model through which the slope (ασ) of the inverse log linear K m -f c plot and empirical constant (α) were obtained. NAP sorption was well described by the cosolvency model with the α value being 0.41-0.53, indicating a methanol-biochar interaction favoring more sorption than the cosolvency based prediction. In particular, the slope (ασ) of 1-NAPA was lower than that of NAP, indicating less reduction of 1-NAPA sorption (i.e., lower α value) by methanol. In comparison with other sorbents, the α value was approximately intermediate between a humic substance and kaolinite clay. An analysis of FT-IR spectra suggested the transformation of O-containing functional groups by methanol, which will subsequently boost the π-π interaction between an organic solute and biochar. Moreover, Ca 2+ -induced sorption between anionic 1-NAPA and a negatively charged biochar surface was also fortified in the methanol mixture. The results revealed unexplored cosolvent effects on organic solute sorption onto biochar and identified the hydrophobic and hydrophilic sorption moieties of biochar as affected by the cosolvent. Copyright © 2017 Elsevier B.V. All rights reserved.

The Effectiveness of Propolis on Gingivitis: A Randomized Controlled Trial

PubMed Central

Paulino, Niraldo; Nör, Jacques E.; Moreira, Alexandre

2014-01-01

Abstract Background: A randomized, double-blind, controlled clinical trial was conducted to evaluate the effectiveness of a propolis rinse on induced gingivitis by using the co-twin study design. Methods: Twenty-one twin pairs (n=42) were enrolled in a gingivitis study with oral hygiene promotion (14 days) and gingivitis induction (21 days). During the gingivitis induction phase, one member of the twin pair was randomly assigned to a 2% typified propolis rinse, and the other was assigned a color-matched 0.05% sodium fluoride plus 0.05% cetylpyridinium chloride rinse (positive control). Patients rinsed twice daily with 20 mL for 30 seconds for 21 days. Gingivitis was measured on days −14 (baseline), 0 (after hygiene phase), and 21 (after no-hygiene phase) by using the Papillary Bleeding Score (PBS) and by standard digital imaging of the gum tissues (G-parameter). Results: The 38 persons who completed the study (age 13–22 years) were well balanced according to PBS at baseline and G-parameter after the initial hygiene phase. After 21 days without oral hygiene, the propolis rinse and positive control rinse groups did not differ significantly for average PBS measurements or G-parameter. Conclusions: Use of a 2% typified propolis rinse was equivalent to a positive control rinse during a 21-day no-hygiene period. PMID:25380344

Synthesis of sub-millimeter calcite from aqueous solution

NASA Astrophysics Data System (ADS)

Reimi, M. A.; Morrison, J. M.; Burns, P. C.

2011-12-01

A novel aqueous synthesis that leads to the formation of calcite (CaCO3) crystals, up to 500μm in diameter, will be used to facilitate the study of contaminant transport in aqueous environmental systems. Existing processes tend to be complicated and often yield nanometer-sized or amorphous CaCO3. The synthesis method presented here, which involves slow mixing of concentrated solutions of CaCl2 ¬and (NH4)2CO3, produces single crystals of rhombohedral calcite in 2 to 4 days. Variations on the experimental method, including changes in pH and solution concentration, were explored to optimize the synthesis. Scanning Electron Microscope images show the differences in size and purity observed when the crystals are grown at pH values ranging from 2 to 6. The crystals grown from solutions of pH 2 were large (up to 500 micrometers in diameter) with minimal polycrystalline calcium carbonate, while crystals grown from solutions with pH values beyond 4 were smaller (up to 100 micrometers in diameter) with significant polycrystalline calcium carbonate. The synthesis method, materials characterization, and use in future actinide contaminant studies will be discussed.

Mercury and Silver in Clinic Wastewater Goodfellow AFB, Texas

DTIC Science & Technology

1989-07-01

SE(JrTY CLASSIFICATION 1b RESTRICTIVE MARINGSuncfassi I ed N/A 2a SCRITY CLASSIFICATION AUTHORITY 3 DISTRIBUTION / AVAiLABILIT OF REPORT N/A Approved...Material suctioned from teeth restoration are collected in a central separator/collection tank. The tank is automatically cleaned by rinsing it with water ...insoluble or sparingly soluble in water . In neutral or alkaline solutions, mercury is oxidized directly to the mercuric state with the formatin of

Colour preference between adults and children during a dental treatment session.

PubMed

Oner Ozdas, Didem; Kazak, Magrur

2017-02-01

It is evidently shown that colour has physical, psychological and sociological effects on human beings. There are many studies showing the effects of colours on brain activity. Colour preferences may change from childhood to adulthood and are significantly different in various age groups. The aim of this study was to evaluate the adults and children in their preference for mouthrinses in various colours under stress condition during a dental treatment session. 240 adults and 263 children were included in the study. Three transparent cups were filled with water, two of which were coloured green/pink rinsing by dissolving a tablet in the water. Cups were placed near the dental unit. During dental treatment sessions, patients were told to rinse their mouth with whichever cup they preferred. Preferred colour of cup, gender and age of patient, number of sessions were recorded. Data were statistically analysed by SPSS 15.0 programme and chi-square tests. Half of all cases preferred water. In adults, while females statistically significantly preferred water, males chose cups with coloured contents (p<0.01). Male adults preferred more than one rinsing solution in a dental treatment session. Children mostly preferred water. Even if adults preferred cups with coloured contents in multi-dental treatment sessions, children regularly preferred water (p<0.001). Female and male children mostly preferred water as a rinsing solution. Water was the most often choice for all patients. Both patients' gender and colours of cups affected choices made by adults and children. Female adults and children were not interested in trying colourful mouthrinses, while male adults were curious about trying colourful mouthrinses during dental treatment sessions under stress condition. Copyright © 2016 Elsevier Inc. All rights reserved.

Preparation of crotaline F-ab antivenom (CroFab) with automated mixing methods: in vitro observations.

PubMed

Vohra, Rais; Kelner, Michael; Clark, Richard F

2009-01-01

Crotaline Polyvalent Ovine Fab antivenom (CroFab, Savage Laboratories and Protherics Inc., Brentwood, TN, USA) preparation requires that the lyophilized powder be manually reconstituted before use. We compared automated methods for driving the product into solution with the standard manual method of reconstitution, and the effect of repeated rinsing of the product vial, on the per-vial availability of antivenom. Normal saline (NS, 10 mL) was added to 12 vials of expired CroFab. Vials were assigned in pairs to each of six mixing methods, including one pair mixed manually as recommended by the product package insert. Each vial's contents were diluted to a final volume of 75 mL of normal saline. Protein concentration was measured with a colorimetric assay. The fluid left in each vial was removed and the vial was washed with 10 mL NS. Total protein yield from each step was calculated. There was no significant change in protein yield among three of five automated mixing methods when compared to manual reconstitution. Repeat rinsing of the product vial with an additional 10 mLs of fluid added to the protein yield regardless of the mixing method used. We found slightly higher protein yields with all automated methods compared to manual mixing, but only two of five comparisons with the standard mixing method demonstrated statistical significance. However, for all methods tested, the addition of a second rinsing and recovery step increased the amount of protein recovered considerably, presumably by allowing solution of protein trapped in the foamy residues. Automated mixing methods and repeat rinsing of the product vial may allow higher protein yields in the preparation of CroFab antivenom.

The substantivity of a number of oral hygiene products determined by the duration of effects on salivary bacteria.

PubMed

Elworthy, A; Greenman, J; Doherty, F M; Newcombe, R G; Addy, M

1996-06-01

The persistence of action, or substantivity, of antimicrobial agents in the mouth appears to be a major variable influencing plaque inhibition. Such substantivity can be assessed by measuring the duration and magnitude of suppression of salivary bacterial numbers produced by antimicrobial agents. Although this has been determined for some agents, there is little information on the substantivity of the numerous products which contain these and other antimicrobial agents. This study was commissioned on the basis that efficacy cannot be assumed merely because a product contains a known active agent. Nine formulations or products were chosen: 2 rinses containing chlorhexidine or C31G, 4 rinses containing cetylpyridinium chloride (CPC) (with and without fluoride and/or alcohol), a minus-CPC control rinse, and 2 toothpastes with and without stannous fluoride. Additionally, water was used as a placebo control. Twenty health dentate volunteers took part in this blind, 10 cell randomized, single rinse, cross-over study, which was balanced for carryover. Mouthrinses were 15 ml volumes and toothpastes 3 gm in 10 ml water slurries rinsed for 60 seconds. On the day of each study volunteers suspended oral hygiene habits and at approximately 9:00 a.m. rinsed with the allocated formulation. Unstimulated saliva samples were obtained immediately before and 30, 60, 180, 300, and 420 minutes after rinsing. The samples were immediately processed for total anaerobic bacterial counts. All rinses except water and the minus CPC control rinse produced significant falls in counts to 30 minutes. Of more relevance in this inter-treatment comparison-designed study, the C31G rinse showed significant substantivity compared to water only for 60 minutes. C31G was highly significantly less substantive than chlorhexidine from 30 minutes to 420 minutes. The CPC rinses were similar and significantly more substantive than their control rinse to between 180 and 300 minutes. The stannous fluoride and control pastes were similarly substantive to 300 minutes, with the stannous fluoride paste remaining substantive compared to water to 430 minutes. Based on antimicrobial action these formulations varied considerably in substantivity and this is likely to reflect their comparative plaque inhibitory properties.

Potential bioavailability of mercury in humus-coated clay minerals.

PubMed

Zhu, Daiwen; Zhong, Huan

2015-10-01

It is well-known that both clay and organic matter in soils play a key role in mercury biogeochemistry, while their combined effect is less studied. In this study, kaolinite, vermiculite, and montmorillonite were coated or not with humus, and spiked with inorganic mercury (IHg) or methylmercury (MeHg). The potential bioavailability of mercury to plants or deposit-feeders was assessed by CaCl2 or bovine serum albumin (BSA) extraction. For uncoated clay, IHg or MeHg extraction was generally lower in montmorillonite, due to its greater number of functional groups. Humus coating increased partitioning of IHg (0.5%-13.7%) and MeHg (0.8%-52.9%) in clay, because clay-sorbed humus provided more strong binding sites for mercury. Furthermore, humus coating led to a decrease in IHg (3.0%-59.8% for CaCl2 and 2.1%-5.0% for BSA) and MeHg (8.9%-74.6% for CaCl2 and 0.5%-8.2% for BSA) extraction, due to strong binding between mercury and clay-sorbed humus. Among various humus-coated clay particles, mercury extraction by CaCl2 (mainly through cation exchange) was lowest in humus-coated vermiculite, explained by the strong binding between humus and vermiculite. The inhibitory effect of humus on mercury bioavailability was also evidenced by the negative relationship between mercury extraction by CaCl2 and mercury in the organo-complexed fraction. In contrast, extraction of mercury by BSA (principally through complexation) was lowest in humus-coated montmorillonite. This was because BSA itself could be extensively sorbed onto montmorillonite. Results suggested that humus-coated clay could substantially decrease the potential bioavailability of mercury in soils, which should be considered when assessing risk in mercury-contaminated soils. Copyright © 2015. Published by Elsevier B.V.

21 CFR 173.375 - Cetylpyridinium chloride.

Code of Federal Regulations, 2014 CFR

2014-04-01

... aqueous solution applied to raw poultry carcasses prior to immersion in a chiller, at a level not to... immersion in a chiller, the treatment will be followed by a potable water rinse of the carcass. [72 FR 67576...

Carbonate dissolution rates in high salinity brines: Implications for post-Noachian chemical weathering on Mars

NASA Astrophysics Data System (ADS)

Phillips-Lander, Charity M.; Parnell, S. R.; McGraw, L. E.; Elwood Madden, M. E.

2018-06-01

A diverse suite of carbonate minerals including calcite (CaCO3) and magnesite (MgCO3) have been observed on the martian surface and in meteorites. Terrestrial carbonates usually form via aqueous processes and often record information about the environment in which they formed, including chemical and textural biosignatures. In addition, terrestrial carbonates are often found in association with evaporite deposits on Earth. Similar high salinity environments and processes were likely active on Mars and some areas may contain active high salinity brines today. In this study, we directly compare calcite and magnesite dissolution in ultrapure water, dilute sulfate and chloride solutions, as well as near-saturated sulfate and chloride brines with known activity of water (aH2O) to determine how dissolution rates vary with mineralogy and aH2O, as well as aqueous cation and anion chemistry to better understand how high salinity fluids may have altered carbonate deposits on Mars. We measured both calcite and magnesite initial dissolution rates at 298 K and near neutral pH (6-8) in unbuffered solutions containing ultrapure water (18 MΩ cm-1 UPW; aH2O = 1), dilute (0.1 mol kg-1; aH2O = 1) and near-saturated Na2SO4 (2.5 mol kg-1, aH2O = 0.92), dilute (0.1 mol kg-1, aH2O = 1) and near-saturated NaCl (5.7 mol kg-1, aH2O = 0.75). Calcite dissolution rates were also measured in dilute and near-saturated MgSO4 (0.1 mol kg-1, aH2O = 1 and 2.7 mol kg-1, aH2O = 0.92, respectively) and MgCl2 (0.1 mol kg-1, aH2O = 1 and 3 mol kg-1, aH2O = 0.73, respectively), while magnesite dissolution rates were measured in dilute and near-saturated CaCl2 (0.1 mol kg-1, aH2O = 1 and 9 mol kg-1, aH2O = 0.35). Initial calcite dissolution rates were fastest in near-saturated MgCl2 brine, while magnesite dissolution rates were fastest in dilute (0.1 mol kg-1) NaCl and CaCl2 solutions. Calcite dissolution rates in near-saturated Na2SO4 were similar to those observed in the dilute solutions (-8.00 ± 0.12 log mol m-2 s-1), while dissolution slowed in both NaCl solutions (0.1 mol kg-1; -8.23 ± 0.10 log mol m-2 s-1 and (5.7 mol kg-1; -8.44 ± 0.11 log mol m-2 s-1), as well as near-saturated MgSO4 brine (2.7 mol kg-1; -8.35 ± 0.05 log mol m-2 s-1). The slowest calcite dissolution rates observed in the near-saturated NaCl brine. Magnesite dissolution rates were ∼5 times faster in the dilute salt solutions relative to UPW, but similar to UPW (-8.47 ± 0.06 log mol m-2 s-1) in near-saturated Na2SO4 brines (-8.41 ± 0.18 log mol m-2 s-1). Magnesite dissolution slowed significantly in near-saturated CaCl2 brine (-9.78 ± 0.10 log mol m-2 s-1), likely due to the significantly lower water activity in these experiments. Overall, magnesite dissolution rates are slower than calcite dissolution rates and follow the trend: All dilute salt solutions >2.5 mol kg-1 Na2SO4 ≈ UPW > 5.7 mol kg-1 NaCl >> 9 mol kg-1 CaCl2. Calcite rates follow the trend 3 mol kg-1 MgCl2 > 2.5 mol kg-1 Na2SO4 ≈ UPW ≈ all dilute salt solutions >2.7 mol kg-1 MgSO4 ≈ 5.7 mol kg-1 NaCl. Magnesite dissolution rates in salt solutions generally decrease with decreasing aH2O in both chloride and sulfate brines, which indicates water molecules act as ligands and participate in the rate-limiting magnesite dissolution step. However, there is no general trend associated with water activity observed in the calcite dissolution rates. Calcite dissolution accelerates in near-saturated MgCl2, but slows in near-saturated NaCl brine despite both brines having similar water activities (aH2O = 0.73 and 0.75, respectively). High Mg calcite was observed as a reaction product in the near-saturated MgCl2, indicating Mg2+ from solution likely substituted for Ca2+ in the initial calcite, releasing additional Ca2+ into solution and increasing the observed calcite dissolution rate. Calcite dissolution rates also increase slightly as Na2SO4 concentration increases, while calcite dissolution rates slow slightly with increasing concentration of MgSO4 and NaCl. However, all of the carbonate rates vary by less than 0.5 log units and are within or near the standard deviation observed for each set of replicate experiments. Carbonate mineral lifetimes in high salinity brines indicate magnesite may be preferentially preserved compared to calcite on Mars. Therefore, Mg-carbonates that have experienced post-depositional aqueous alteration are more likely to preserve paleoenvironmental indicators and potential biosignatures. Rapid weathering of carbonates in circum-neutral pH sulfate brines may provide a potential source of cations for abundant sulfate minerals observed on Mars, Ceres, and other planetary bodies.

Effects of a Novel Whitening Formulation on Dental Enamel

PubMed Central

Takesh, Thair; Sargsyan, Anik; Anbarani, Afarin; Ho, Jessica; Wilder-Smith, Petra

2017-01-01

Objective The goal of this study was to evaluate the enamel whitening effects of 2 new test formulations, one of which was a rinse, and the other a whitening strip. Materials and Methods Forty enamel chips were prepared from 20 healthy extracted teeth (2 from each tooth). After pre-staining and colorimetry to measure L* and b* values, 20 matched samples were immersed in either test or control rinses, and then colorimetry was performed again after 1 hr, 2 hr, 3 hr, 6 hr, 12 hr, 24 hr and 48 hrs (Each hour equates to one month of clinical use at the recommended dosage of 1 minute exposure 2 times a day). The remaining 20 matched samples were exposed to the test or control whitening strips and colorimetry was performed every 30 minutes for a total of 10 treatments. Results Overall, the whitening performance of test and control strips was similar. The test and control rinses had a similar lightening effect over the first 3 hours (equivalent to 3 months of clinical use). Subsequently, the control rinse continued to lighten samples, whereas the test rinse had little further effect. Conclusion Test and control-whitening strips showed similar effects; over time whitening strips showed a greater lightening effect than whitening rinses. PMID:28706755

Hydration Repulsion between Carbohydrate Surfaces Mediated by Temperature and Specific Ions

PubMed Central

Chen, Hsieh; Cox, Jason R.; Ow, Hooisweng; Shi, Rena; Panagiotopoulos, Athanassios Z.

2016-01-01

Stabilizing colloids or nanoparticles in solution involves a fine balance between surface charges, steric repulsion of coating molecules, and hydration forces against van der Waals attractions. At high temperature and electrolyte concentrations, the colloidal stability of suspensions usually decreases rapidly. Here, we report a new experimental and simulation discovery that the polysaccharide (dextran) coated nanoparticles show ion-specific colloidal stability at high temperature, where we observed enhanced colloidal stability of nanoparticles in CaCl2 solution but rapid nanoparticle-nanoparticle aggregation in MgCl2 solution. The microscopic mechanism was unveiled in atomistic simulations. The presence of surface bound Ca2+ ions increases the carbohydrate hydration and induces strongly polarized repulsive water structures beyond at least three hydration shells which is farther-reaching than previously assumed. We believe leveraging the binding of strongly hydrated ions to macromolecular surfaces represents a new paradigm in achieving absolute hydration and colloidal stability for a variety of materials, particularly under extreme conditions. PMID:27334145

The effect of divalent salt in chondroitin sulfate solutions

NASA Astrophysics Data System (ADS)

Aranghel, D.; Badita, C. R.; Radulescu, A.; Moldovan, L.; Craciunescu, O.; Balasoiu, M.

2016-03-01

Chondroitin-4 sulfate (CS4) is the main glycosaminoglycan extracted from bovine trachea. CS4 play an important role in osteoarthritis treatment, anticoagulant activity, reduces the degradation of cartilage matrix components, reduces necrosis and apoptosis of chondrocytes and reduces the activity of collagenase. Chondroitin sulfate is also responsible for proteoglycans degradation. Chondroitin sulfate can bind calcium ions with different affinities, depending on their sulfation position. The purpose of this study was to determine the structural properties and the influence of Ca2+ cations. We carried out measurements on CS4 solutions and mixtures of liquid CS4 with Ca2+ by Small-Angle Neutron Scattering (SANS). CS4 have a mass fractal behavior and the addition of a salt (CaCl2) in CS4 solutions generates the appearance of a correlation peak due to local ordering between adjacent chains with inter-chain distances between 483 Å and 233 Å for a calcium concentration of 0.01% w/w.

Hydration Repulsion between Carbohydrate Surfaces Mediated by Temperature and Specific Ions

NASA Astrophysics Data System (ADS)

Chen, Hsieh; Cox, Jason R.; Ow, Hooisweng; Shi, Rena; Panagiotopoulos, Athanassios Z.

2016-06-01

Stabilizing colloids or nanoparticles in solution involves a fine balance between surface charges, steric repulsion of coating molecules, and hydration forces against van der Waals attractions. At high temperature and electrolyte concentrations, the colloidal stability of suspensions usually decreases rapidly. Here, we report a new experimental and simulation discovery that the polysaccharide (dextran) coated nanoparticles show ion-specific colloidal stability at high temperature, where we observed enhanced colloidal stability of nanoparticles in CaCl2 solution but rapid nanoparticle-nanoparticle aggregation in MgCl2 solution. The microscopic mechanism was unveiled in atomistic simulations. The presence of surface bound Ca2+ ions increases the carbohydrate hydration and induces strongly polarized repulsive water structures beyond at least three hydration shells which is farther-reaching than previously assumed. We believe leveraging the binding of strongly hydrated ions to macromolecular surfaces represents a new paradigm in achieving absolute hydration and colloidal stability for a variety of materials, particularly under extreme conditions.

Calcium-dependent mechanisms mediate the vasorelaxant effects of Tridax procumbens (Lin) aqueous leaf extract in rat aortic ring.

PubMed

Salahdeen, Hussein M; Idowu, Gbolahan O; Yemitan, Omoniyi K; Murtala, Babatunde A; Alada, Abdul-Rasak A

2014-05-01

Tridax procumbens leaf extract has a folk reputation as an antihypertensive agent in Nigeria. Evidence suggests that it has a relaxant effect on smooth muscles. The present study was designed to investigate the role of calcium in the vasorelaxant effect of this extract. Concentration-response studies with noradrenaline (NA), KCl and CaCl2 were carried out in rat aortic rings with and without the extract in physiological salt solution (PSS) (n=6 each). Also, the role of intracellular calcium mobilization was studied by measuring the phasic response to NA in Ca2+-free N,N-ethylene glycol tetraacetic acid (EGTA) PSS (n=6). The results showed that the contractile responses to either NA or KCl were attenuated (p<0.05) in the presence of the extract. Also, the extract attenuated the contractile response to CaCl2 in the presence of NA or KCl (p<0.05) in the Ca2+-free EGTA PSS, while the phasic response to NA was significantly (p<0.05) diminished. These results suggest that the vasorelaxant effect of T. procumbens leaf extract may be mediated by a non-specific, non-competitive inhibition of Ca2+ influx as well as by inhibition of Ca2+ mobilization from intracellular stores. This implies that it may contain vasorelaxant agents that may have calcium antagonistic potential.

New evidence about the relationship between water channel activity and calcium in salinity-stressed pepper plants.

PubMed

Cabañero, Francisco J; Martínez-Ballesta, M Carmen; Teruel, José A; Carvajal, Micaela

2006-02-01

This study, of how Ca2+ availability (intracellular, extracellular or linked to the membrane) influences the functionality of aquaporins of pepper (Capsicum annuum L.) plants grown under salinity stress, was carried out in plants treated with NaCl (50 mM), CaCl2 (10 mM), and CaCl2 (10 mM) + NaCl (50 mM). For this, water transport through the plasma membrane of isolated protoplasts, and the involvement of aquaporins and calcium (extracellular, intracellular and linked to the membrane) has been determined. After these treatments, it could be seen that the calcium concentration was reduced in the apoplast, in the cells and on the plasma membrane of roots of pepper plants grown under saline conditions; these concentrations were increased or restored when extra calcium was added to the nutrient solution. Protoplasts extracted from plants grown under Ca2+ starvation showed no aquaporin functionality. However, for the protoplasts to which calcium was added, an increase of aquaporin functionality of the plasma membrane was observed [osmotic water permeability (Pf) inhibition after Hg addition]. Interestingly, when verapamil (a Ca2+ channel blocker) was added, no functionality was observed, even when Ca2+ was added with verapamil. Therefore, calcium seems to be involved in plasma membrane aquaporin regulation via a chain of processes within the cell but not by alteration of the stability of the plasma membrane.

Model Implementation of Boron Removal Using CaCl2-CaO-SiO2 Slag System for Solar-Grade Silicon

NASA Astrophysics Data System (ADS)

Chen, Hui; Wang, Ye; Zheng, Wenjia; Li, Qincan; Yuan, Xizhi; Morita, Kazuki

2017-12-01

A new CaCl2-CaO-SiO2 slag system was recently proposed to remove boron from metallurgy-grade silicon by oxidized chlorination and evaporation. To further investigate the boron transformation process at a high temperature, a model implementation to present the transfer of boron from molten silicon to the gas phase via slag is introduced. Heat transfer, fluid flow, the chemical reactions at the interface and surface, the mass transfer and diffusion of boron in the molten silicon and slag, and the evaporation of BOCl and CaCl2 were coupled in this model. After the confirmation of the thermal field, other critical parameters, including the boron partition ratios ( L B) for this slag from 1723 K to 1823 K (1450 °C to 1550 °C), the thicknesses of the velocity boundary layer at the surface and interface, the mass transfer coefficients of the boundary layer at the surface and interface, and partial pressure of BOCl in the gas phase were analyzed to determine the rate-limiting step. To verify this model implementation, boron removal experiments were carried out at various temperatures and with various initial mass ratios of slag to silicon ( μ). The evaporation rate of CaCl2 was also measured by thermogravimetry analysis (TGA).

Origin of CaCl2 brines by basalt-seawater interaction: Insights provided by some simple mass balance calculations

NASA Astrophysics Data System (ADS)

Hardie, Lawrence A.

1983-06-01

Modern rift zone hydrothermal brines are typically CaCl2-bearing brines, an unusual chemical signature they share with certain oil field brines, fluid inclusions in ore minerals and a few uncommon saline lakes. Many origins have been suggested for such CaCl2 brines but in the Reykjanes, Iceland, geothermal system a strong empirical case can be made for a basalt-seawater interaction origin. To examine this mechanism of CaCl2 brine evolution some simple mass balance calculations were carried out. Average Reykjanes olivine tholeiite was “reacted” with average North Atlantic seawater to make an albite-chlorite-epidotesphene rock using Al2O3 as the conservative rock component and Cl as the conservative fluid component. The excess components released by the basalt to the fluid were “precipitated” at 275° C as quartz, calcite, anhydrite, magnetite and pyrite to complete the conversion to greenstone. The resulting fluid was a CaCl2 brine of seawater chlorinity with a composition remarkably similar to the actual Reykjanes brine at 1750 m depth. Thus, the calculations strongly support the idea that the Reykjanes CaCl2 brines result from “closed system” oceanic basalt-seawater interaction (albitization — chloritization mechanism) at greenschist facies temperatures. The calculation gives a seawater: basalt mass ratio of 3∶1 to 4∶1 (vol. ratio of 9∶1 to 12∶1), in keeping with experimental results, submarine vent data and with ocean crust cooling calculations. The brine becomes anoxic because there is insufficient dissolved or combined oxygen to balance all the Fe released from the basalt during alteration. Large excesses of Ca are released to the fluid and precipitate out in the form of anhydrite which essentially sweeps the brine free of sulfate leaving an elevated Ca concentration. The calculated rock-water interaction basically involves Na + Mg + SO4 ⇌ Ca + K, simulating chemical differences observed between oceanic basalts and greenstones from many mid-ocean ridges.

Influence of salt and rinsing protocol on the structure of PAH/PSS polyelectrolyte multilayers.

PubMed

Feldötö, Zsombor; Varga, Imre; Blomberg, Eva

2010-11-16

A quartz crystal microbalance (QCM) and dual polarization interferometry (DPI) have been utilized to study how the structure of poly(allylamine hydrochloride) (PAH)/poly(styrene sulfonate) (PSS) multilayers is affected by the rinsing method (i.e., the termination of polyelectrolyte adsorption). The effect of the type of counterions used in the deposition solution was also investigated, and the polyelectrolyte multilayers were formed in a 0.5 M electrolyte solution (NaCl and KBr). From the measurements, it was observed that thicker layers were obtained when using KBr in the deposition solution than when using NaCl. Three different rinsing protocols have been studied: (i) the same electrolyte solution as used during multilayer formation, (ii) pure water, and (iii) first a salt solution (0.5 M) and then pure water. When the multilayer with PAH as the outermost layer was exposed to pure water, an interesting phenomenon was discovered: a large change in the energy dissipation was measured with the QCM. This could be attributed to the swelling of the layer, and from both QCM and DPI it is obvious that only the outermost PAH layer swells (to a thickness of 25-30 nm) because of a decrease in ionic strength and hence an increase in intra- and interchain repulsion, whereas the underlying layers retain a very rigid and compact structure with a low water content. Interestingly, the outermost PAH layer seems to obtain very similar thicknesses in water independent of the electrolyte used for the multilayer buildup. Another interesting aspect was that the measured thickness with the DPI evaluated by a single-layer model did not correlate with the estimated thickness from the model calculations performed on the QCM-D data. Thus, we applied a two-layer model to evaluate the DPI data and the results were in excellent agreement with the QCM-D results. To our knowledge, this evaluation of DPI data has not been done previously.

A comparison of dioctahedral smectite and iodine glycerin cream with topical mouth rinse in treatment of chemotherapy induced oral mucositis: a pilot study.

PubMed

Lin, Jin-Xiang; Fan, Zu-Yan; Lin, Qu; Wu, Dong-Hao; Wu, Xiang-Yuan; Chen, Yan-Ru; Fang, Heng-Ying; Wu, Dong-Bing; Wen, Jing-Yun; Dong, Min; Ma, Xiao-Kun; Wan, Xiang-Bo

2015-04-01

To compare the efficacy of dioctahedral smectite and iodine glycerin (DSIG) cream with topical mouth rinse (composed of saline, gentamicin and Vitamin B12) in treatment of chemotherapy induced oral mucositis (OM). A total of 130 intensive chemotherapy or stem cells transplantation induced OM patients were recruited. Among these patients, 67 patients received topical mouth rinse and 63 patients received DSIG cream treatment. The OM would be treated on the OM appearance and sustained for 5 days. OM severity was measured daily using The American Oncology Nursing Society recommended Oral Assessment Guideline (OAG) score system. Compared with topical mouth rinse treatment, a significant lower OAG score was observed in DSIG cream treated patients. Specifically, the OAG scores were respectively 12.1 ± 1.1, 12.0 ± 1.2, 11.3 ± 1.3 and 10.4 ± 1.3 from day 2 to day 5 in topical mouth rinse treatment subgroup. Correspondingly, the OAG scores were respectively 10.2 ± 1.0, 9.3 ± 0.9, 8.5 ± 0.6 and 8.0 ± 0.2 for DSIG cream treatment subset (all P < 0.05). Importantly, compared with topical mouth rinse treatment, the DSIG cream significantly shortened OM repair time (4.68 ± 0.98 vs. 8.76 ± 1.80 days, P < 0.001). After 5 days treatment, 54 patients (85.7%) obtained complete regression with an OAG score ≤8, and 7 patients (11.1%) had partial regression with an OAG score of 9-10 in DSIG cream treatment subgroup. However, only 2 patients (3.0%) obtained completed regression and 32 patients (47.8%) had partial regression in topical mouth rinse treatment cohort. Moreover, no serious side-effect was observed in both cohorts. Compared with topical mouth rinse, DSIG cream significantly lowered the OAG score and shortened OM duration. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of gamma radiation on the physico-chemical properties of alginate-based films and beads

NASA Astrophysics Data System (ADS)

Huq, Tanzina; Khan, Avik; Dussault, Dominic; Salmieri, Stephane; Khan, Ruhul A.; Lacroix, Monique

2012-08-01

Alginate solution (3%, w/v) was prepared using deionized water from its powder. Then the solution was exposed to gamma radiation (0.1-25 kGy). The alginate films were prepared by solution casting. It was found that gamma radiation has strong effect on alginate solution. At low doses, mechanical strength of the alginate films improved but after 5 kGy dose, the strength started to decrease. The mechanism of alginate radiolysis in aqueous solution is discussed. Film formation was not possible from alginate solution at doses >5 kGy. The mechanical properties such as puncture strength (PS), puncture deformation (PD), viscoelasticity (Y) coefficient of the un-irradiated films were investigated. The values of PS, PD and Y coefficient of the films were 333 N/mm, 3.20 mm and 27%, respectively. Alginate beads were prepared from 3% alginate solution (w/v) by ionotropic gelation method in 5% CaCl2 solution. The rate of gel swelling improved in irradiated alginate-based beads at low doses (up to 0.5 kGy).

Effect of flow rate and concentration difference on reverse electrodialysis system

NASA Astrophysics Data System (ADS)

Kwon, Kilsugn; Han, Jaesuk; Kim, Daejoong

2013-11-01

Various energy conversion technologies have been developed to reduce dependency on limited fossil fuels, including wind power, solar power, hydropower, ocean power, and geothermal power. Among them, reverse electrodialysis (RED), which is one type of salinity gradient power (SGP), has received much attention due to high reliability and simplicity without moving parts. Here, we experimentally evaluated the RED performance with several parameters like flow rate of concentrated and dilute solution, concentration difference, and temperature. RED was composed of endplates, electrodes, spacers, anion exchange membrane, and cation exchange membrane. Endplates are made by a polypropylene. It included the electrodes, flow field for the electrode rinse solution, and path to supply a concentrated and dilute solution. Titanium coated by iridium and ruthenium was used as the electrode. The electrode rinse solution based on hexacyanoferrate system is used to reduce the power loss generated by conversion process form ionic current to electric current. Maximum power monotonously increases as increasing flow rate and concentration difference. Net power has optimal point because pumping power consumption increases with flow rate. This work was supported by Basic Science Research Program (Grat No. NRF-2011-0009993) through the National Research Foundation of Korea.

Comparison of the antimicrobial efficacy of chlorhexidine, sodium fluoride, fluoride with essential oils, alum, green tea, and garlic with lime mouth rinses on cariogenic microbes.

PubMed

Thomas, Ann; Thakur, Sneha; Mhambrey, Sanjana

2015-01-01

A number of natural mouth rinse formulations are being proposed as an alternative to the widely used chemical mouth rinses. To evaluate and compare the antimicrobial efficacy of chlorhexidine (0.2%), sodium fluoride (0.05%), fluoride with essential oils (0.05%), alum (0.02 M), green tea, and garlic with lime mouth rinses against Streptococcus mutans, lactobacilli, and Candida albicans. The three microbes were isolated from the saliva samples collected from children with severe early childhood caries. The zone of minimum inhibition was assessed using agar diffusion method. The data were statistically analyzed using SPSS software. Against S. mutans and lactobacilli, chlorhexidine mouth rinse was found to be the most effective as compared to sodium fluoride (P < 0.001, P < 0.001), fluoride with essential oils (P < 0.001, P < 0.001), alum (P < 0.001, P < 0.001), green tea (P < 0.001, P < 0.001), and garlic with lime (P < 0.001, P < 0.001) mouth rinses, respectively. But against C. albicans, garlic with lime mouth rinse was found to be the most effective as compared to chlorhexidine (P < 0.001), sodium fluoride (P < 0.001), fluoride with essential oils (P < 0.001), alum (P < 0.001), and green tea (P < 0.001) mouth rinses. Against S. mutans and lactobacilli, after chlorhexidine mouth rinse, garlic with lime mouth rinse was found to be significantly more effective than sodium fluoride (P = 0.053, P = 0.001), fluoride with essential oils (P < 0.001, P < 0.001), alum (P < 0.001, P < 0.001), and green tea (P < 0.001, P < 0.001) mouth rinses. As a natural mouth rinse, garlic with lime mouth rinse was found to be the most promising. However, further studies are needed in this field.

Chemical method for producing smooth surfaces on silicon wafers

DOEpatents

Yu, Conrad

2003-01-01

An improved method for producing optically smooth surfaces in silicon wafers during wet chemical etching involves a pre-treatment rinse of the wafers before etching and a post-etching rinse. The pre-treatment with an organic solvent provides a well-wetted surface that ensures uniform mass transfer during etching, which results in optically smooth surfaces. The post-etching treatment with an acetic acid solution stops the etching instantly, preventing any uneven etching that leads to surface roughness. This method can be used to etch silicon surfaces to a depth of 200 .mu.m or more, while the finished surfaces have a surface roughness of only 15-50 .ANG. (RMS).

Sorption-desorption and transport of trimethoprim and sulfonamide antibiotics in agricultural soil: effect of soil type, dissolved organic matter, and pH.

PubMed

Zhang, Ya-Lei; Lin, Shuang-Shuang; Dai, Chao-Meng; Shi, Lu; Zhou, Xue-Fei

2014-05-01

Use of animal manure is a main source of veterinary pharmaceuticals (VPs) in soil and groundwater through a series of migration processes. The sorption-desorption and transport of four commonly used VPs including trimethoprim (TMP), sulfapyridine, sulfameter, and sulfadimethoxine were investigated in three soil layers taken from an agricultural field in Chongming Island China and two types of aqueous solution (0.01 M CaCl2 solution and wastewater treatment plant effluent). Results from sorption-desorption experiments showed that the sorption behavior of selected VPs conformed to the Freundlich isotherm equation. TMP exhibited higher distribution coefficients (K d = 6.73-9.21) than other sulfonamides (K d = 0.03-0.47), indicating a much stronger adsorption capacity of TMP. The percentage of desorption for TMP in a range of 8-12 % is not so high to be considered significant. Low pH (

Crystallization of sodium chloride from a concentrated calcium chloride-potassium chloride-sodium chloride solution in a CMSMPR crystallizer: Observation of crystal size distribution and model validation

NASA Astrophysics Data System (ADS)

Choi, Byung Sang

Compared to overwhelming technical data available in other advanced technologies, knowledge about particle technology, especially in particle synthesis from a solution, is still poor due to the lack of available equipment to study crystallization phenomena in a crystallizer. Recent technical advances in particle size measurement such as Coulter counter and laser light scattering have made in/ex situ study of some of particle synthesis, i.e., growth, attrition, and aggregation, possible with simple systems. Even with these advancements in measurement technology, to grasp fully the crystallization phenomena requires further theoretical and technical advances in understanding such particle synthesis mechanisms. Therefore, it is the motive of this work to establish the general processing parameters and to produce rigorous experimental data with reliable performance and characterization that rigorously account for the crystallization phenomena of nucleation, growth, aggregation, and breakage including their variations with time and space in a controlled continuous mixed-suspension mixed-product removal (CMSMPR) crystallizer. This dissertation reports the results and achievements in the following areas: (1) experimental programs to support the development and validation of the phenomenological models and generation of laboratory data for the purpose of testing, refining, and validating the crystallization process, (2) development of laboratory well-mixed crystallizer system and experimental protocols to generate crystal size distribution (CSD) data, (3) the effects of feed solution concentration, crystallization temperature, feed flow rate, and mixing speed, as well as different types of mixers resulting in the evolution of CSDs with time from a concentrated brine solution, (4) with statistically designed experiments the effects of processing variables on the resultant particle structure and CSD at steady state were quantified and related to each of those operating conditions by studying the detailed crystallization processes, such as nucleation, growth, and breakage, as well as agglomeration. The purification of CaCl2 solution involving the crystallization of NaCl from the solution mixture of CaCl2, KCl, and NaCl as shipped from Dow Chemical, Ludington, in a CMSMPR crystallizer was studied as our model system because of its nucleation and crystal growth tendencies with less agglomeration. This project also generated a significant body of experimental data that are available at URL that is http://www.che.utah.edu/˜ring/CrystallizationWeb.

Solute mixing regulates heterogeneity of mineral precipitation in porous media: Effect of Solute Mixing on Precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cil, Mehmet B.; Xie, Minwei; Packman, Aaron I.

Synchrotron X-ray microtomography was used to track the spatiotemporal evolution of mineral precipitation and the consequent alteration of the pore structure. Column experiments were conducted by injecting CaCl2 and NaHCO3 solutions into granular porous media either as a premixed supersaturated solution (external mixing) or as separate solutions that mixed within the specimen (internal mixing). The two mixing modes produced distinct mineral growth patterns. While internal mixing promoted transverse heterogeneity with precipitation at the mixing zone, external mixing favored relatively homogeneous precipitation along the flow direction. The impact of precipitation on pore water flow and permeability was assessed via 3-D flowmore » simulations, which indicated anisotropic permeability evolution for both mixing modes. Under both mixing modes, precipitation decreased the median pore size and increased the skewness of the pore size distribution. Such similar pore-scale evolution patterns suggest that the clogging of individual pores depends primarily on local supersaturation state and pore geometry.« less

Four Interesting Mysteries with Seemingly Conflicting Explanations

NASA Astrophysics Data System (ADS)

Delorenzo, Ron

2000-04-01

Four mysteries with seemingly contradictory solutions are presented to make chemistry courses more interesting and relevant to students' lives: (1) Why might women become intoxicated more easily than men? (2) Why might alcohol consumption enhance cigarettes' carcinogenic effects? (3) Why might the use of Vaseline Intensive Care Hand Lotion as a lubricant increase the number of unwanted pregnancies and promote the spread of HIV? (4) Why does oil-based Vaseline Intensive Care Hand Lotion rinse off in water? Although the solutions to these mysteries appear to contradict one another, the contradictions are reconciled by considering a fifth mystery: Why does red wine go with red meat and white wine go with fish?

Impact of Sn/F Pre-Treatments on the Durability of Protective Coatings against Dentine Erosion/Abrasion

PubMed Central

Ganss, Carolina; Lussi, Adrian; Peutzfeldt, Anne; Naguib Attia, Nader; Schlueter, Nadine

2015-01-01

For preventing erosive wear in dentine, coating with adhesives has been suggested as an alternative to fluoridation. However, clinical studies have revealed limited efficacy. As there is first evidence that Sn2+ increases bond strength of the adhesive Clearfil SE (Kuraray), the aim of the present study was to investigate whether pre-treatment with different Sn2+/F− solutions improves the durability of Clearfil SE coatings. Dentine samples (eight groups, n=16/group) were freed of smear layer (0.5% citric acid, 10 s), treated (15 s) either with no solution (control), aminefluoride (AmF, 500 ppm F−, pH 4.5), SnCl2 (800/1600 ppm Sn2+; pH 1.5), SnCl2/AmF (500 ppm F−, 800 ppm Sn2+, pH 1.5/3.0/4.5), or Elmex Erosion Protection Rinse (EP, 500 ppm F−, 800 ppm Sn2+, pH 4.5; GABA International), then rinsed with water (15 s) and individually covered with Clearfil SE. Subsequently the specimens were subjected to an erosion/abrasion protocol consisting of 1320 cycles of immersion in 0.5% citric acid (5°C/55°C; 2 min) and automated brushing (15 s, 200 g, NaF-toothpaste, RDA 80). As the coatings proved stable up to 1320 cycles, 60 modified cycles (brushing time 30 min/cycle) were added. Wear was measured profilometrically. After SnCl2/AmF, pH 4.5 or EP pre-treatment all except one coating survived. In the other groups, almost all coatings were lost and there was no significant difference to the control group. Pre-treatment with a Sn2+/F− solution at pH 4.5 seems able to improve the durability of adhesive coatings, rendering these an attractive option in preventing erosive wear in dentine. PMID:26075906

Wave-front propagation of rinsing flows on rotating semiconductor wafers

NASA Astrophysics Data System (ADS)

Frostad, John M.; Ylitalo, Andy; Walls, Daniel J.; Mui, David S. L.; Fuller, Gerald G.

2016-11-01

The semiconductor manufacturing industry is migrating to a cleaning technology that involves dispersing cleaning solutions onto a rotating wafer, similar to spin-coating. Advantages include a more continuous overall fabrication process, lower particle level, no cross contamination from the back side of a wafer, and less usage of harsh chemicals for a lower environmental impact. Rapid rotation of the wafer during rinsing can be more effective, but centrifugal forces can pull spiral-like ribbons of liquid radially outward from the advancing wave-front where particles can build up, causing higher instances of device failure at these locations. A better understanding of the rinsing flow is essential for reducing yield losses while taking advantage of the benefits of rotation. In the present work, high-speed video and image processing are used to study the dynamics of the advancing wave-front from an impinging jet on a rotating substrate. The flow-rate and rotation-speed are varied for substrates coated with a thin layer of a second liquid that has a different surface tension than the jet liquid. The difference in surface tension of the two fluids gives rise to Marangoni stresses at the interface that have a significant impact on the rinsing process, despite the extremely short time-scales involved.

Preparation and Characterization of Hydroxyapatite Coating on AZ31 Mg Alloy for Implant Applications

PubMed Central

Salman, S. A.; Kuroda, K.; Okido, M.

2013-01-01

Magnesium alloys as biodegradable metal implants in orthopaedic research received a lot of interest in recent years. They have attractive biological properties including being essential to human metabolism, biocompatibility, and biodegradability. However, magnesium can corrode too rapidly in the high-chloride environment of the physiological system, loosing mechanical integrity before the tissue has sufficiently healed. Hydroxyapatite (HAp) coating was proposed to decrease the corrosion rate and improve the bioactivity of magnesium alloy. Apatite has been cathodically deposited on the surface of Mg alloy from solution that composed of 3 mM Ca(H2PO4)2 and 7 mM CaCl2 at various applied potentials. The growing of HAp was confirmed on the surface of the coatings after immersion in SBF solution for 7 days. The coating obtained at −1.4 V showed higher corrosion resistance with bioactive behaviors. PMID:23533371

Optical and Thermal Behaviors of Polyamide-Layered Silicate Nanocomposites Based on 4,4'-Azodibenzoic Acid by Solution Intercalation Technique

NASA Astrophysics Data System (ADS)

Faghihi, Khalil; Shabanian, Meisam

2011-04-01

Two new samples of polyamide-montmorillonite reinforced nanocomposites based on 4,4'-azodibenzoic acid were prepared by a convenient solution intercalation technique. Polyamide (PA) 4 as a source of polymer matrix was synthesized by the direct polycondensation reaction of 4,4'-azodibenzoic acid 2 with 4,4'-diamino diphenyl sulfone 3 in the presence of triphenyl phosphate (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). Morphology and structure of the resulting PA-nanocomposite films 4a and 4b with 10 and 20% silicate particles were characterized by FTIR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The effect of clay dispersion and the interaction between clay and polymeric chains on the properties of nanocomposite films were investigated by using Uv-vis spectroscopy, thermogravimetric analysis (TGA) and water uptake measurements.

Fermentation of cucumbers brined with calcium chloride instead of sodium chloride.

PubMed

McFeeters, Roger F; Pérez-Díaz, Ilenys

2010-04-01

Waste water containing high levels of NaCl from cucumber fermentation tank yards is a continuing problem for the pickled vegetable industry. A major reduction in waste salt could be achieved if NaCl were eliminated from the cucumber fermentation process. The objectives of this project were to ferment cucumbers in brine containing CaCl(2) as the only salt, to determine the course of fermentation metabolism in the absence of NaCl, and to compare firmness retention of cucumbers fermented in CaCl(2) brine during subsequent storage compared to cucumbers fermented in brines containing both NaCl and CaCl(2) at concentrations typically used in commercial fermentations. The major metabolite changes during fermentation without NaCl were conversion of sugars in the fresh cucumbers primarily to lactic acid which caused pH to decrease to less than 3.5. This is the same pattern that occurs when cucumbers are fermented with NaCl as the major brining salt. Lactic acid concentration and pH were stable during storage and there was no detectable production of propionic acid or butyric acid that would indicate growth of spoilage bacteria. Firmness retention in cucumbers fermented with 100 to 300 mM CaCl(2) during storage at a high temperature (45 degrees C) was not significantly different from that obtained in fermented cucumbers with 1.03 M NaCl and 40 mM CaCl(2). In closed jars, cucumber fermentations with and without NaCl in the fermentation brine were similar both in the chemical changes caused by the fermentative microorganisms and in the retention of firmness in the fermented cucumbers.

Fermentation profiles of Manzanilla-Aloreña cracked green table olives in different chloride salt mixtures.

PubMed

Bautista-Gallego, J; Arroyo-López, F N; Durán-Quintana, M C; Garrido-Fernández, A

2010-05-01

NaCl plays an important role in table olive processing affecting the flavour and microbiological stability of the final product. However, consumers demand foods low in sodium, which makes necessary to decrease levels of this mineral in fruits. In this work, the effects of diverse mixtures of NaCl, CaCl(2) and KCl on the fermentation profiles of cracked directly brined Manzanilla-Aloreña olives, were studied by means of response surface methodology based in a simplex lattice mixture design with constrains. All salt combinations led to lactic acid processes. The growth of Enterobacteriaceae populations was always limited and partially inhibited by the presence of CaCl(2). Only time to reach half maximum populations and decline rates of yeasts, which were higher as concentrations of NaCl or KCl increased, were affected, and correspondingly modelled, as a function of salt mixtures. However, lactic acid bacteria growth parameters could not be related to initial environmental conditions. They had a longer lag phase, slower growth and higher population levels than yeasts. Overall, the presence of CaCl(2) led to a slower Enterobacteriaceae and lactic acid bacteria growth than the traditional NaCl brine but to higher yeast activity. The presence of CaCl(2) in the fermentation brines also led to higher water activity, lower pH and combined acidity as well as a faster acidification while NaCl and KCl had fairly similar behaviours. Apparently, NaCl may be substituted in diverse proportions with KCl or CaCl(2) without substantially disturbing water activity or the usual fermentation profiles while producing olives with lower salt content. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Comparison of the antibacterial effect of sodium hypochlorite and aloe vera solutions as root canal irrigants in human extracted teeth contaminated with enterococcus faecalis.

PubMed

Sahebi, S; Khosravifar, N; Sedighshamsi, M; Motamedifar, M

2014-03-01

The main purpose of a root canal treatment is to eliminate the bacteria and their products from the pulp space. Sodium hypochlorite has excellent antibacterial properties, but also some negative features. The aim of the present study is to compare the antimicrobial effect of Aloe Vera solution with sodium hypochlorite on E.faecalis in the root canals of human extracted teeth. Sixty human extracted single rooted teeth were selected for this in vitro study. The teeth recruited in this study had no cracks, internal resorption, external resorption and calcification. Enterococcus faecalis was injected in the root canals of all teeth. The teeth were then divided into three groups randomly. Each group consisted of 20 teeth that were all rinsed with one of the following solutions: sodium hypochlorite 2.5%, Aloe vera and normal saline. Subsequent to rinsing, root canals of all teeth were sampled. The samples were cultured and growth of the bacteria was assessed after 48 hours. The number of colonies of the bacteria was then counted. The difference between the inhibitory effect of Aloe vera and normal saline on E.faecalis was not significant according to independent t-test (p= 0.966). The inhibitory effect of sodium hypochlorite on E.faecalis was much greater than that of Aloe vera and normal saline (p< 0.001). Aloe vera solution is not recommended as a root canal irrigator, but future studies are suggested to investigate the antibacterial effect of Aloe vera with longer duration of exposure and as an intra canal medicament.

Vitamins C and E improve regrowth and reduce lipid peroxidation of blackberry shoot tips following cryopreservation.

PubMed

Uchendu, Esther E; Leonard, Scott W; Traber, Maret G; Reed, Barbara M

2010-01-01

Oxidative processes involved in cryopreservation protocols may be responsible for the reduced viability of tissues after liquid nitrogen exposure. Antioxidants that counteract these reactions should improve recovery. This study focused on oxidative lipid injury and the effects of exogenous vitamin E (tocopherol, Vit E) and vitamin C (ascorbic acid, Vit C) treatments on regrowth at four critical steps of the plant vitrification solution number 2 (PVS2) vitrification cryopreservation technique; pretreatment, loading, rinsing, and regrowth. Initial experiments showed that Vit E at 11-15 mM significantly increased regrowth (P < 0.001) when added at any of the four steps. There was significantly more malondialdehyde (MDA), a lipid peroxidation product, at each of the steps than in fresh untreated shoot tips. Vit E uptake was assayed at each step and showed significantly more alpha- and gamma-tocopherols in treated shoots than those without Vit E. Vit E added at each step significantly reduced MDA formation and improved shoot regrowth. Vit C (0.14-0.58 mM) also significantly improved regrowth of shoot tips at each step compared to the controls. Regrowth medium with high iron concentrations and Vit C decreased recovery. However, in iron-free medium, Vit C significantly improved recovery. Treatments with Vit E (11 mM) and Vit C (0.14 mM) combined were not significantly better than Vit C alone. We recommend adding Vit C (0.28 mM) to the pretreatment medium, the loading solution or the rinse solution in the PVS2 vitrification protocol. This is the first report of the application of vitamins for improving cryopreservation of plant tissues by minimizing oxidative damage.

In vitro activity of an ear rinse containing tromethamine, EDTA, benzyl alcohol and 0.1% ketoconazole on Malassezia organisms from dogs with otitis externa.

PubMed

Cole, Lynette K; Luu, Dao H; Rajala-Schultz, Paivi J; Meadows, Cheyney; Torres, Audrey H

2007-04-01

The purpose of this study was to evaluate the in vitro activity of an ear rinse containing tromethamine, EDTA, benzyl alcohol and 0.1% ketoconazole in purified water on Malassezia organisms from dogs with otitis externa. Malassezia organisms were collected from ear swab samples from the external ear canal of 19 dogs with otitis externa plus one control strain of Malassezia pachydermatis. Three test solutions were evaluated: ER (EDTA, tromethamine, benzyl alcohol), ER + keto (EDTA, tromethamine, benzyl alcohol, ketoconazole), and H2O (purified water). Ten-millilitre aliquots of each test solution was transferred into 20 tubes and inoculated with one of the isolates (1 tube per isolate: 19 clinical and 1 control strain). Samples were retrieved from each tube at five time points (0, 15, 30, 45 and 60 min), transferred to Petri dishes, mixed with Sabouraud dextrose agar supplemented with 0.5% Tween 80 and incubated. Following incubation, the plates were examined for growth and colonies counted as colony-forming units per millilitre. The data were analysed using a repeated measures analysis, with pair-wise comparisons of solution-time combinations. There was a significant reduction in Malassezia growth in ER + keto at all time points (P < 0.0001) compared to time zero. Neither ER nor H2O had any effect on the growth of Malassezia. ER + keto was significantly more effective in reducing Malassezia growth (P < 0.0001) at all time points compared to both ER and H2O. ER + keto may be useful in the treatment of Malassezia otitis externa. Future studies should be performed to evaluate the in vivo efficacy of ER + keto as treatment for otic infections caused by Malassezia.

Resist surface crosslinking using amine-based reactive rinses to mitagate pattern collapse in thin film lithography

NASA Astrophysics Data System (ADS)

Yeh, Wei-Ming; Lawson, Richard A.; Tolbert, Laren M.; Henderson, Clifford L.

2012-03-01

As the semiconductor industry continues to push to smaller critical dimensions, pattern collapse during lithographic processing caused by unbalanced capillary forces during the final rinse and drying process has become an important problem that can limit the practical resolution of a resist material to feature sizes larger than its intrinsic resolution limit. One of the primary modes of pattern collapse is via elastoplastic pattern deformation which is strongly related to the mechanical properties of the resist. One approach to mitigating such collapse problems is to enhance the mechanical properties of the resist features. Since such modification of resist physical properties for pattern collapse purposes is difficult to achieve through modified formulation of the resist itself (i.e. due to the complex set of requirements that a resist must satisfy and the complex set of physical and chemical phenomena that underlie the imaging processing itself), we have pursued an alternative strategy for improving the resist mechanical properties after features are developed in the film but before they are rinsed and dried. The family of techniques being developed in this work function through the use of aqueous compatible reactive rinse solutions that can be applied to developed resist features while they are wet during normal rinse processing on a track system. By applying these techniques during the rinse process, the resist features can be strengthened before they are subjected to significant capillary forces during the final drying step. In this work, the use of diamine compounds to reactively crosslink the surface of resists containing carboxylic acid groups through formation of amide bonds using carbodiimide chemistry has been explored. One advantage of this approach is that it is an aqueous process that should be easily compatible with high volume, track-based lithographic processes. Contact angle studies and x-ray photoelectron spectroscopy (XPS) were used to characterize the surface crosslinking reaction using such diamine surface rinse treatments. Pattern collapse test structures were fabricated and analyzed to measure the amount of mechanical property improvement imparted by such treatments. Application of such amine reactive rinses was found to clearly result in an improvement in the resistance of resists to pattern collapse as observed by SEM. A comparison of the critical stress at the point of pattern collapse as a function of resist feature size also clearly shows a significant improvement in mechanical resilience of resist samples processed with the reactive rinse treatment.

Moving zone Marangoni drying of wet objects using naturally evaporated solvent vapor

DOEpatents

Britten, Jerald A.

1997-01-01

A surface tension gradient driven flow (a Marangoni flow) is used to remove the thin film of water remaining on the surface of an object following rinsing. The process passively introduces by natural evaporation and diffusion of minute amounts of alcohol (or other suitable material) vapor in the immediate vicinity of a continuously refreshed meniscus of deionized water or another aqueous-based, nonsurfactant rinsing agent. Used in conjunction with cleaning, developing or wet etching application, rinsing coupled with Marangoni drying provides a single-step process for 1) cleaning, developing or etching, 2) rinsing, and 3) drying objects such as flat substrates or coatings on flat substrates without necessarily using heat, forced air flow, contact wiping, centrifugation or large amounts of flammable solvents. This process is useful in one-step cleaning and drying of large flat optical substrates, one-step developing/rinsing and drying or etching/rinsing/drying of large flat patterned substrates and flat panel displays during lithographic processing, and room-temperature rinsing/drying of other large parts, sheets or continuous rolls of material.

Moving zone Marangoni drying of wet objects using naturally evaporated solvent vapor

DOEpatents

Britten, J.A.

1997-08-26

A surface tension gradient driven flow (a Marangoni flow) is used to remove the thin film of water remaining on the surface of an object following rinsing. The process passively introduces by natural evaporation and diffusion of minute amounts of alcohol (or other suitable material) vapor in the immediate vicinity of a continuously refreshed meniscus of deionized water or another aqueous-based, nonsurfactant rinsing agent. Used in conjunction with cleaning, developing or wet etching application, rinsing coupled with Marangoni drying provides a single-step process for (1) cleaning, developing or etching, (2) rinsing, and (3) drying objects such as flat substrates or coatings on flat substrates without necessarily using heat, forced air flow, contact wiping, centrifugation or large amounts of flammable solvents. This process is useful in one-step cleaning and drying of large flat optical substrates, one-step developing/rinsing and drying or etching/rinsing/drying of large flat patterned substrates and flat panel displays during lithographic processing, and room-temperature rinsing/drying of other large parts, sheets or continuous rolls of material. 5 figs.

Effect of calcium and salicylic acid on quality retention in relation to antioxidative enzymes in radish stored under refrigerated conditions.

PubMed

Devi, Jomika; Bhatia, Surekha; Alam, M S; Dhillon, Tarsem Singh

2018-03-01

Effect of post harvest treatments with calcium chloride (CaCl 2 ) and salicylic acid (SA) on physiological and biochemical parameters in relation to activities of antioxidative enzymes were investigated in radish. Radish of variety Punjab Safed Mooli 2 was harvested, washed and treated with CaCl 2 (1, 1.5 and 2%) or SA (1, 1.5 and 2 mM). Treated as well as untreated radish were placed in open trays and stored under refrigerated (5 ± 1 °C, 90% RH) conditions for 42 days. Treatment of radish with CaCl 2 and SA slowed down changes in physiological weight, colour, total soluble solids, ascorbic acid, titrable acidity, total phenolics and antioxidant activity. Treated samples exhibited higher enhancement in activities of antioxidant enzymes viz. catalase (CAT), superoxide dismutase (SOD), glutathione reductase (GR), peroxidase (POD), dehydroascorbate reductase (DHAR) and monodehydro-ascorbate reductase (MDHAR) than untreated samples. However SA was found to be more effective in slowing down the metabolic activities of radish as compared to CaCl 2 treatment. Among all the treatments, 1.5 mM SA maintained the quality parameters to greater extent probably by reducing the oxidative stress to larger extent due to highest activities of antioxidative enzymes and can be used to enhance the shelf life of radish during refrigerated storage.

Highly Porous, Rigid-Rod Polyamide Aerogels with Superior Mechanical Properties and Unusually High Thermal Conductivity.

PubMed

Williams, Jarrod C; Nguyen, Baochau N; McCorkle, Linda; Scheiman, Daniel; Griffin, Justin S; Steiner, Stephen A; Meador, Mary Ann B

2017-01-18

We report here the fabrication of polyamide aerogels composed of poly-p-phenylene-terephthalamide, the same backbone chemistry as DuPont's Kevlar. The all-para-substituted polymers gel without the use of cross-linker and maintain their shape during processing-an improvement over the meta-substituted cross-linked polyamide aerogels reported previously. Solutions containing calcium chloride (CaCl 2 ) and para-phenylenediamine (pPDA) in N-methylpyrrolidinone (NMP) at low temperature are reacted with terephthaloyl chloride (TPC). Polymerization proceeds over the course of 5 min resulting in gelation. Removal of the reaction solvent via solvent exchange followed by extraction with supercritical carbon dioxide provides aerogels with densities ranging from 0.1 to 0.3 g/cm 3 , depending on the concentration of calcium chloride, the formulated number of repeat units, n, and the concentration of polymer in the reaction mixture. These variables were assessed in a statistical experimental study to understand their effects on the properties of the aerogels. Aerogels made using at least 30 wt % CaCl 2 had the best strength when compared to aerogels of similar density. Furthermore, aerogels made using 30 wt % CaCl 2 exhibited the lowest shrinkage when aged at elevated temperatures. Notably, whereas most aerogel materials are highly insulating (thermal conductivities of 10-30 mW/m K), the polyamide aerogels produced here exhibit remarkably high thermal conductivities (50-80 mW/(m K)) at the same densities as other inorganic and polymer aerogels. These high thermal conductivities are attributed to efficient phonon transport by the rigid-rod polymer backbone. In conjunction with their low cost, ease of fabrication with respect to other polymer aerogels, low densities, and high mass-normalized strength and stiffness properties, these aerogels are uniquely valuable for applications such as lightweighting in consumer electronics, automobiles, and aerospace where weight reduction is desirable but trapping of heat may be undesirable-applications where other polymer aerogels have to date otherwise been unsuitable-creating new opportunities for commercialization of aerogels.

Short-term relative antibacterial effect of octenidine dihydrochloride on the oral microflora in orthodontically treated patients.

PubMed

Dogan, Alev Aksoy; Adiloglu, Ali K; Onal, Suleyman; Cetin, Emel Sesli; Polat, Esra; Uskun, Ersin; Koksal, Fatih

2008-11-01

To evaluate the efficacy of common antiseptic mouth rinses and octenidine dihydrochloride (OCT). The antibacterial activities of antiseptics against total and cariogenic bacteria (Streptococcus mutans and Lactobacillus species) in saliva were studied in vitro and in vivo. After unstimulated saliva was collected, one of the mouth rinse solutions was applied for 30seconds. Saliva samples were collected 15, 30, 60, and 120min later and evaluated for their bacterial count. OCT had a significantly greater inhibitory effect on the studied bacteria than 0.2% chlorhexidine gluconate (CHX) and 7.5% polyvinylpyrrolidone-iodine complex (PVP-I) from 15min to 120min following the application (p<0.01). The antiseptic efficacy of 0.2% CHX on total bacteria and Lactobacillus species was very similar to the efficacy observed with 7.5% PVP-I mouth solution from 15min up to 120min. Streptococcus mutans was completely inhibited by 0.15mg/ml PVP-I, 0.5mg/ml CHX, and 0.1mg/ml OCT concentrations, while Streptococcus salivarius was inhibited by 0.15mg/ml PVP-I, 2mg/ml CHX, and 0.8mg/ml OCT concentrations. Lactococcus lactis subspecies lactis was inhibited with 0.00313mg/ml OCT, 30mg/ml PVP-I, and 0.0063mg/ml CHX concentrations. OCT compared favorably with CHX and PVP-I in its antibacterial effects, both in vitro and in vivo (p<0.01).

Influence of pH, temperature, and concentration on stabilization of aqueous hornet silk solution and fabrication of salt-free materials.

PubMed

Kameda, Tsunenori

2015-01-01

We found that an aqueous solution of silk from cocoons produced by hornet larvae (hornet silk) can be obtained when the solution is adjusted to basic conditions of pH > 9.2. It is known that native hornet cocoons can be dissolved in concentrated aqueous solution of salts, such as lithium bromide (LiBr) and calcium chloride (CaCl2). Upon the removal of these salts from solution by dialysis, solidification, gelation, or sedimentation of hornet silk is known to occur. In the present study, under basic conditions, however, no such solidification occurred, even after salt removal. In this study, ammonia was used for alkalization of solution because it is volatilized during the casting process and pure hornet silk materials can be obtained after drying. The effects of the concentrations of hornet silk and ammonia, as well as dialysis temperature, on preventing gelation during dialysis were investigated. Dialysis conditions that limit the degradation of hornet silk by hydrolysis in alkali solution were identified. Moreover, casting conditions to prepare flexible and transparent hornet silk film from aqueous ammonia solution were optimized. Molecular structural analysis of hornet silk in aqueous ammonia solution and cast film indicated the formation of α-helix conformations. © 2014 Wiley Periodicals, Inc.

The impact of chlorhexidine mouth rinse on the bond strength of polycarbonate orthodontic brackets.

PubMed

Hussein, Farouk Ahmed; Hashem, Mohammed Ibrahim; Chalisserry, Elna P; Anil, Sukumaran

2014-11-01

The purpose of the current in-vivo study was to assess the effect of using 0.12% chlorhexidine (CHX) mouth rinse, before bonding, on shear bond strength of polycarbonate brackets bonded with composite adhesive. Eighteen orthodontic patients with a mean age 21.41 ± 1.2 years, who were scheduled to have 2 or more first premolars extracted, were included in this study. Patients were referred for an oral prophylaxis program which included, in part, the use of a mouth rinse. Patients were divided into 2 groups, a test group of 9 patients who used 0.12% CHX gluconate mouth rinse twice daily and a control group of 9 patients who used a mouth rinse without CHX, but with same color. After 1 week, polycarbonate brackets were bonded to first premolars with Transbond XT composite adhesive. Premolars were extracted after 28 days and tested for shear bond strength on a universal testing machine. Student's t-test was used to compare shear bond strengths of both groups. No statistically significant difference was found in bond strengths' values between both groups. The test group (with CHX) has mean shear bond strength of 14.21 ± 2.42 MPa whereas the control group (without CHX) revealed a mean strength of 14.52 ± 2.31 MPa. The use of 0.12% CHX mouth rinse, for one week before bonding, did not affect the shear bond strength of polycarbonate brackets bonded with Transbond composite. Furthermore, these brackets showed clinically acceptable bond strength.

Molecular emission in laser-induced breakdown spectroscopy: An investigation of its suitability for chlorine quantification on Mars

NASA Astrophysics Data System (ADS)

Vogt, D. S.; Rammelkamp, K.; Schröder, S.; Hübers, H. W.

2018-03-01

The intensity of the molecular CaCl emission in LIBS spectra is examined in order to evaluate its suitability for the detection of chlorine in a Martian environment. Various mixtures resembling Martian targets with varying Cl content are investigated under simulated Martian conditions. The reactions leading to the formation of CaCl are modeled based on reaction kinetics and are used to fit the measured CaCl band intensities. MgCl bands are also investigated as potential alternatives to CaCl, but no MgCl bands can be identified in samples containing both Mg and Cl. The study confirms that CaCl is well suited for the indirect detection of chlorine, but finds a strong dependence on the concentrations of Ca and Cl in the sample. Spectra from samples with a high chlorine concentration can have low-intensity CaCl emission due to a deficiency of Ca. A qualitative estimate of the sample composition is possible based on the ratio of the band intensity of CaCl to the intensity of Ca emission lines. Time-resolved measurements show that the CaCl concentration in the plasma is highest after about 1 μs.

Influence of clay particles on microfluidic-based preparation of hydrogel composite microsphere

NASA Astrophysics Data System (ADS)

Hong, Joung Sook

2016-05-01

For the successful fabrication of a hydrogel composite microsphere, this study aimed to investigate the influence of clay particles on microsphere formation in a microfluidic device which has flow focusing and a 4.5:1 contraction channel. A poly alginic acid solution (2.0 wt.%) with clay particles was used as the dispersed phase to generate drops in an oil medium, which then merged with drops of a CaCl2 solution for gelation. Drop generations were observed with different flow rates and particles types. When the flow rate increased, drop generation was enhanced and drop size decreased by the build-up of more favorable hydrodynamic flow conditions to detach the droplets. The addition of a small amount of particles insignificantly changed the drop generation behavior even though it reduced interfacial tension and increased the viscosity of the solution. Instead, clays particles significantly affected hydro-gelation depending on the hydrophobicity of particles, which produced further heterogeneity in the shape and size of microsphere.

Unusual effect of the magnetic field component of the microwave radiation on aqueous electrolyte solutions.

PubMed

Horikoshi, Satoshi; Sumi, Takuya; Serpone, Nick

2012-01-01

The heating characteristics of aqueous electrolyte solutions (NaCl, KCl, CaCl2, NaBF4, and NaBr) of varying concentrations in ultrapure water by 2.45 GHz microwave radiation from a single-mode resonance microwave device and a semiconductor microwave generator were examined under conditions where the electric field (E-field) was dominant and where the magnetic field (H-field) dominated. Although magnetic field heating is not generally used in microwave chemistry, the electrolyte solutions were heated almost entirely by the microwaves' H-field. The heating rates under H-field irradiation at the higher concentrations of electrolytes (0.125 M to 0.50 M) exceeded the rates under E-field irradiation. This inversion phenomenon in heating is described in terms of the penetration depth of the microwaves. On the other hand, the action of the microwave radiation on ethylene glycol containing an electrolyte differed from that observed for water under E-field and H-field conditions.

Interaction of fullerene (C60) nanoparticles with humic acid and alginate coated silica surfaces: measurements, mechanisms, and environmental implications.

PubMed

Chen, Kai Loon; Elimelech, Menachem

2008-10-15

The deposition kinetics of fullerene (C60) nanoparticles onto bare silica surfaces and surfaces precoated with humic acid and alginate are investigated over a range of monovalent (NaCI) and divalent (CaCl2) salt concentrations using a quartz crystal microbalance. Because simultaneous aggregation of the fullerene nanoparticles occurs, especially at higher electrolyte concentrations, we normalize the observed deposition rates by the corresponding favorable (transport-limited) deposition rates to obtain the attachment efficiencies, alpha. The deposition kinetics of fullerene nanoparticles onto bare silica surfaces are shown to be controlled by electrostatic interactions and van der Waals attraction, consistent with the classical particle deposition behavior where both favorable and unfavorable deposition regimes are observed. The presence of dissolved humic acid and alginate in solution leads to significantly slower deposition kinetics due to steric repulsion. Precoating the silica surfaces with humic acid and alginate exerts similar steric stabilization in the presence of NaCl. In the presence of CaCl2, the deposition kinetics of fullerene nanoparticles onto both humic acid- and alginate-coated surfaces are relatively high, even at relatively low (0.3 mM) calcium concentration. This behavior is attributed to the macromolecules undergoing complex formation with calcium ions, which reduces the charge and steric influences of the adsorbed macromolecular layers.

Effects of various final irrigants on the shear bond strength of resin-based sealer to dentin.

PubMed

Kandaswamy, Deivanayagam; Venkateshbabu, Nagendrababu; Arathi, Ganesh; Roohi, Riaz; Anand, Suresh

2011-01-01

This study has been designed to evaluate the effect of strong (MTAD) or soft (1- hydroxyethylidene - 1, 1-bisphosphonate (HEBP) final irrigating solution on the shear bond strength of AH plus sealer to coronal dentin. 17% EDTA was used as the reference. Forty freshly extracted human maxillary first premolars were prepared using different irrigation protocols (n=10). All the test groups had 1.3% NaOCl as initial rinse and followed by specific final rinse for each group: G1 - distilled water(control), G2 - 17% EDTA, G3- 18% HEBP and G4 - MTAD. Sections of polyethylene tubes that are 3mm long were filled with freshly mixed sealer and placed on the dentin surfaces. The bonding between the sealer and dentine surface was evaluated using shear bond testing. The values were statistically evaluated using one-way ANOVA followed by Tukey's test. Significant difference was found among the irrigating regimes. EDTA showed highest bond strength followed by HEBP and MTAD.

Relationship of Cell Sap pH to Organic Acid Change During Ion Uptake 1

PubMed Central

Hiatt, A. J.

1967-01-01

Excised roots of barley (Hordeum vulgare, var. Campana) were incubated in KCl, K2SO4, CaCl2, and NaCl solutions at concentrations of 10−5 to 10−2 n. Changes in substrate solution pH, cell sap pH, and organic acid content of the roots were related to differences in cation and anion absorption. The pH of expressed sap of roots increased when cations were absorbed in excess of anions and decreased when anions were absorbed in excess of cations. The pH of the cell sap shifted in response to imbalances in cation and anion uptake in salt solutions as dilute as 10−5 n. Changes in cell sap pH were detectable within 15 minutes after the roots were placed in 10−3 n K2SO4. Organic acid changes in the roots were proportional to expressed sap pH changes induced by unbalanced ion uptake. Changes in organic acid content in response to differential cation and anion uptake appear to be associated with the low-salt component of ion uptake. PMID:16656506

The effect of aging on sequestration and bioaccessibility of oxytetracycline in soils.

PubMed

Liu, Yuxia; Bao, Yanyu; Cai, Zhang; Zhang, Zhenzihao; Cao, Peilin; Li, Xinqian; Zhou, Qixing

2015-07-01

Veterinary antibiotics introduced into soil environment may change the composition and functioning of soil microbial communities and promote the spreading of antibiotic resistance. Actual risks depend on the antibiotic's bioaccessibility and sequestration in soils, which may vary with contact time and soil properties. We elucidated changes in the horsebean plant's bioaccessible oxytetracycline with increasing contact time in three different soils (cinnamon, red, and brown soil) and observed discrepancy in oxytetracycline dissipation using sequential extractions with H2O-, 0.01 M CaCl2-, and Mcllvaine- in the same three soils. The results showed lower quantities of oxytetracycline with increasing contact time over 20 days than the level in freshly contaminated soils but hugely discrepant quantities among the three tested soils. In addition, aging largely reduced dissipation of H2O-, 0.01 M CaCl2-, and Mcllvaine- extracted oxytetracycline in soils before planting. However, bioturbation helped increase the H2O-, CaCl2-, and Mcllvaine- extracted oxytetracyline from cinnamon and brown soils with aging. Lastly, correlation analysis indicated that bioaccessibility of oxytetracycline significantly correlates with the total of H2O-, CaCl2-, and Mcllvaine- extracted oxytetracycline (0.676**, p < 0.01) in soils, especially the H2O- (0.789**, p < 0.01) and Mcllvaine- (0.686**, p < 0.01) extracted oxytetracycline with aging. Overall, this study provides some basic understanding of the aging effect on sequestration and bioaccessibility of veterinary antibiotics in soils.

Effects of etch-and-rinse and self-etch adhesives on dentin MMP-2 and MMP-9.

PubMed

Mazzoni, A; Scaffa, P; Carrilho, M; Tjäderhane, L; Di Lenarda, R; Polimeni, A; Tezvergil-Mutluay, A; Tay, F R; Pashley, D H; Breschi, L

2013-01-01

Auto-degradation of collagen matrices occurs within hybrid layers created by contemporary dentin bonding systems, by the slow action of host-derived matrix metalloproteinases (MMPs). This study tested the null hypothesis that there are no differences in the activities of MMP-2 and -9 after treatment with different etch-and-rinse or self-etch adhesives. Tested adhesives were: Adper Scotchbond 1XT (3M ESPE), PQ1 (Ultradent), Peak LC (Ultradent), Optibond Solo Plus (Kerr), Prime&Bond NT (Dentsply) (all 2-step etch-and-rinse adhesives), and Adper Easy Bond (3M ESPE), Tri-S (Kuraray), and Xeno-V (Dentsply) (1-step self-etch adhesives). MMP-2 and -9 activities were quantified in adhesive-treated dentin powder by means of an activity assay and gelatin zymography. MMP-2 and MMP-9 activities were found after treatment with all of the simplified etch-and-rinse and self-etch adhesives; however, the activation was adhesive-dependent. It is concluded that all two-step etch-and-rinse and the one-step self-etch adhesives tested can activate endogenous MMP-2 and MMP-9 in human dentin. These results support the role of endogenous MMPs in the degradation of hybrid layers created by these adhesives.

Effects of Etch-and-Rinse and Self-etch Adhesives on Dentin MMP-2 and MMP-9

PubMed Central

Mazzoni, A.; Scaffa, P.; Carrilho, M.; Tjäderhane, L.; Di Lenarda, R.; Polimeni, A.; Tezvergil-Mutluay, A.; Tay, F.R.; Pashley, D.H.; Breschi, L.

2013-01-01

Auto-degradation of collagen matrices occurs within hybrid layers created by contemporary dentin bonding systems, by the slow action of host-derived matrix metalloproteinases (MMPs). This study tested the null hypothesis that there are no differences in the activities of MMP-2 and -9 after treatment with different etch-and-rinse or self-etch adhesives. Tested adhesives were: Adper Scotchbond 1XT (3M ESPE), PQ1 (Ultradent), Peak LC (Ultradent), Optibond Solo Plus (Kerr), Prime&Bond NT (Dentsply) (all 2-step etch-and-rinse adhesives), and Adper Easy Bond (3M ESPE), Tri-S (Kuraray), and Xeno-V (Dentsply) (1-step self-etch adhesives). MMP-2 and -9 activities were quantified in adhesive-treated dentin powder by means of an activity assay and gelatin zymography. MMP-2 and MMP-9 activities were found after treatment with all of the simplified etch-and-rinse and self-etch adhesives; however, the activation was adhesive-dependent. It is concluded that all two-step etch-and-rinse and the one-step self-etch adhesives tested can activate endogenous MMP-2 and MMP-9 in human dentin. These results support the role of endogenous MMPs in the degradation of hybrid layers created by these adhesives. PMID:23128110

Influence of solution acidity and CaCl2 concentration on the removal of heavy metals from metal-contaminated rice soils.

PubMed

Kuo, S; Lai, M S; Lin, C W

2006-12-01

Soil washing is considered a useful technique for remediating metal-contaminated soils. This study examined the release edges of Cd, Zn, Ni, Cr, Cu or Pb in two contaminated rice soils from central Taiwan. The concentrations exceeding the trigger levels established by the regulatory agency of Taiwan were Cu, Zn, Ni and Cr for the Ho-Mei soil and Pb for the Nan-Tou soil. Successive extractions with HCl ranging from 0 to 0.2 M showed increased release of the heavy metals with declining pH, and the threshold pH value below which a sharp increase in the releases of the heavy metals was highest for Cd, Zn, and Ni (pH 4.6 to 4.9), intermediate for Pb and Cu (3.1 to 3.8) and lowest for Fe (2.1), Al (2.2) and Cr (1.7) for the soils. The low response slope of Ni and Cr particularly for the rice soils make soil washing with the acid up to the highest concentration used ineffective to reduce their concentrations to below trigger levels. Although soil washing with 0.1 M HCl was moderately effective in reducing Cu, Pb, Zn and Cd, which brought pH of the soils to 1.1+/-0.1 (S.D.), the concurrent release of large quantities of Fe and Al make this remediation technique undesirable for the rice soils containing high clay. Successive washings with 0.01 M HCl could be considered an alternative as the dissolution of Fe and Al was minimal, and between 46 to 64% of Cd, Zn, and Cu for the Ho-Mei soil and 45% of Pb in the Na-Tou soil were extracted after four successive extractions with this dilute acid solution. The efficacy of Cd extraction improved if CaCl2 was added to the acid solution. The correlation analysis revealed that Cr extracted was highly correlated (P < 0.001) with Fe extracted, whereas the Cu, Ni, Zn, Cd or Pb extracted was better correlated (P < 0.001) with Al than with Fe extracted. It is possible that the past seasonal soil flooding and drainage in the soils for rice production was conducive to incorporating Cr within the structure of Fe oxide, thereby making them extremely insoluble even in 0.2 M HCl solution. The formation of solid solution of Ni with Al oxide was also possible, making it far less extractable than Cd, Zn, Cu, or Pb with the acid concentrations used.

Photo and Thermal Behavior of New Reinforced Polyamide-nanocomposite Montmorillonite on 2,3-Pyrazin Dicarboxylic Acid

NASA Astrophysics Data System (ADS)

Faghihi, Khalil; Samiei, Mojtaba; Hajibeygi, Mohsen

2012-06-01

Two new samples of reinforce polyamidemontmorillonite nanocomposites were synthesized by a convenient solution intercalation technique. Polyamide (PA) 3 as a source of polymer matrix was synthesized by the direct polycondensation reaction of pyrazine 2,3-dicarboxylic acid 1 with 4,4'-diamino diphenyl ether 2 in the presence of triphenyl phosphite (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). The resulting nanocomposite films were characterized by Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). The results showed that organo-modified clay was dispersed homogeneously in PA matrix. TGA indicated an enhancement of thermal stability of new nanocomposites compared with the pure polymer.

Effect of three ophthalmic solutions on chemical conjunctivitis in the neonate.

PubMed

Yasunaga, S

1977-02-01

In an attempt to reduce chemical conjunctivitis after silver nitrate prophylaxis, three different ophthalmic solutions (sodium chloride, sterile water, and a boric acid-sodium borate solution) were used to irrigate the eyes immediately after prophylaxis in 450 neonates. Sterile water significantly reduced (P less than .02) the prevalence of chemical conjunctivitis when compared to the conventional sodium chloride rinse. A significantly greater prevalence of chemical irritation in low-birth-weight infants was also noted (P less than .02).

Ethanol wet-bonding technique sensitivity assessed by AFM.

PubMed

Osorio, E; Toledano, M; Aguilera, F S; Tay, F R; Osorio, R

2010-11-01

In ethanol wet bonding, water is replaced by ethanol to maintain dehydrated collagen matrices in an extended state to facilitate resin infiltration. Since short ethanol dehydration protocols may be ineffective, this study tested the null hypothesis that there are no differences in ethanol dehydration protocols for maintaining the surface roughness, fibril diameter, and interfibrillar spaces of acid-etched dentin. Polished human dentin surfaces were etched with phosphoric acid and water-rinsed. Tested protocols were: (1) water-rinse (control); (2) 100% ethanol-rinse (1-min); (3) 100% ethanol-rinse (5-min); and (4) progressive ethanol replacement (50-100%). Surface roughness, fibril diameter, and interfibrillar spaces were determined with atomic force microscopy and analyzed by one-way analysis of variance and the Student-Newman-Keuls test (α = 0.05). Dentin roughness and fibril diameter significantly decreased when 100% ethanol (1-5 min) was used for rinsing (p < 0.001). Absolute ethanol produced collapse and shrinkage of collagen fibrils. Ascending ethanol concentrations did not collapse the matrix and shrank the fibrils less than absolute ethanol-rinses.

The effect of polyvinylpyrrolidone-sodium hyaluronate gel (Gelclair) on oral microbial colonization and pain control compared with other rinsing solutions in patients with oral mucositis after allogeneic stem cells transplantation

PubMed Central

Vokurka, Samuel; Skardova, Jana; Hruskova, Renata; Kabatova-Maxova, Klara; Svoboda, Tomas; Bystricka, Eva; Steinerova, Katerina; Koza, Vladimir

2011-01-01

Summary Background Gelclair is an oral lubricating gel used in the management of oral mucositis (OM). We evaluated its efficacy, tolerance and impact on oral cavity microbial colonization in patients with OM after allogeneic hematopoietic stem cells transplantation. Material/Method Gelclair was administered in a group of 22 patients with active OM. A control group of 15 patients used other rinsing solutions (chlorhexidine, benzydamine, salvia). Tests with oral cavity swabs for microbiology analysis were performed once a week. Results The characteristics of OM in both groups were comparable, and rinsing solutions had satisfactory tolerability. There was no difference in the median improvement of oral intake and OM-related pain relief, which was assessed mostly as “slight effect”. In the Gelclair group, the effect duration was longer (median 3 [0–5] vs. 1 [0–3] hours, p=0.001). There was significant increase of Enterococcus faecalis and Candida sp. colonization of the oral cavity over the course of the hospitalization and significantly reduced incidence of such colonization in patients with OM in the Gelclair group: 1/22 (5%) vs. 6/15 (40%), p=0.01. In vitro tests showed inhibited growth of Enterococcus faecalis and Candida sp. colonies within the area of the Gelclair application. Conclusions Gelclair may be individually helpful in the management of OM and pain in patients after allogeneic stem cells transplantation. Its use did not lead to worsened oral bacterial and yeast colonization and probably even helped to protect mucosa from Enterococcus and Candida sp. Further studies based on larger cohorts are needed. PMID:21959611

Inhibition of nitrite-induced toxicity in channel catfish by calcium chloride and sodium chloride

USGS Publications Warehouse

Tommasso J.R., Wright; Simco, B.A.; Davis, K.B.

1980-01-01

Environmental chloride has been shown to inhibit methemoglobin formation in fish, thereby offering a protective effect against nitrite toxicity. Channel catfish (Ictalurus punctatus) were simultaneously exposed to various environmental nitrite and chloride levels (as either CaCl2 or NaCl) in dechlorinated tap water (40 mg/L total hardness, 47 mg/L alkalinity, 4 mg/L chloride, pH = 6.9-7.1, and temperature 21-24°C). Methemoglobin levels in fish simultaneously exposed to 2.5 mg/L nitrite and up to 30 mg/L chloride as either CaCl2 or NaCl were similar but significantly lower than in unprotected fish. Exposure to 10 mg/L nitrite and 60 mg/L chloride resulted in methemoglobin levels similar to those of the controls; most unprotected fish died. Fish exposed to 10 mg/L nitrite had significantly lower methemoglobin levels when protected with 15.0 mg/L chloride as CaCl2 than with NaCl. Fish exposed to nitrite in the presence of 60 mg/L chloride (as either CaCl2 or NaCl) had similar 24-h LC50 values that were significantly elevated above those obtained in the absence of chloride. Calcium had little effect on tolerance to nitrite toxicity in channel catfish in contrast to its large effect reported in steelhead trout (Salmo gairdneri).

Evaluation of organic amendment on the effect of cadmium bioavailability in contaminated soils using the DGT technique and traditional methods.

PubMed

Yao, Yu; Sun, Qin; Wang, Chao; Wang, Pei-Fang; Ding, Shi-Ming

2017-03-01

Organic amendments have been widely proposed as a remediation technology for metal-contaminated soils, but there exist controversial results on their effectiveness. In this study, the effect of pig manure addition on cadmium (Cd) bioavailability in Cd-contaminated soils was systematically evaluated by one dynamic, in situ technique of diffusive gradients in thin films (DGT) and four traditional methods based on the equilibrium theory (soil solution concentration and the three commonly used extractants, i.e., acetic acid (HAc), ethylenediamine tetraacetic acid (EDTA), and calcium chloride (CaCl 2 ). Wheat and maize were selected for measurement of plant Cd uptake. The results showed that pig manure addition could promote the growth of two plants, accompanied by increasing biomasses of shoots and roots with increasing doses of pig manure addition. Correspondingly, increasing additions of pig manure reduced plant Cd uptake and accumulation, as indicated by the decreases of Cd concentrations in shoots and roots. The bioavailable concentrations of Cd in Cd-contaminated soils reflected by the DGT technique obviously decreased with increasing doses of pig manure addition, following the same changing trend as plant Cd uptake. Changes in soil solution Cd concentration and extractable Cd by HAc, EDTA, and CaCl 2 in soils were similar to DGT measurement. Meanwhile, the capability of Cd resupply from solid phase to soil solution decreased with increasing additions of pig manure, as reflected by the decreases in the ratio (R) value of C DGT to C sol . Positive correlations were observed between various bioavailable indicators of Cd in soils and Cd concentrations in the tissues of the two plants. These findings provide stronger evidence that pig manure amendment is effective in reducing Cd mobility and bioavailability in soils and it is an ideal organic material for remediation of Cd-contaminated soils.

Mobility and dissipation of chlorpyriphos and quinalphos in sandy clay loam in an agroecosystem-a laboratory-based soil column study.

PubMed

G P, Bindumol; C C, Harilal

2017-09-15

Leaching potential of pesticides, apart from climatological factors, depends on soil physical properties, soil-pesticide interaction and chemical nature of the molecule. Recent investigations have revealed the presence of various organophosphate pesticides in various agroecosystems. The present study investigated the soil transport mechanism of commonly used organophosphate pesticides in acidic sandy clay loam soils of Kerala State, India. Packed soil column experiment was undertaken under laboratory condition for 30 days. Unsaturated flow was carried out using distilled water/0.01 M CaCl 2 solution after applying chlorpyriphos and quinalphos at the rate of 0.04% a.i.ha -1 and 0.025% a.i.ha -1 , respectively. The study revealed the retention of residues of chlorpyriphos and quinalphos in the top 5-cm layer. Irrespective of the applied concentration of chlorpyriphos and quinalphos, the relative concentration of the pesticides in soil was similar. About 56% of the applied chemicals were dissipated in 30 days of unsaturated flow. A new dissipation compound iron, tricarbonyl [N-(phenyl-2-pyridinylmethyene) benzenamine-N, N'], was detected in GCMS analysis of soil extract from distilled water percolated soil. The dissipation of chlorpyriphos and quinalphos was faster in 0.01 M CaCl 2 -treated soil column. Among the pesticides analysed, the residue of quinalphos was detected in leachate.

Biomolecular Doping of Single-Walled Carbon Nanotubes by Thyroid Hormone

NASA Astrophysics Data System (ADS)

Rojas, Enrique; Paulson, Scott; Stern, Mike; Staii, Cristian; Dratman, Mary; Johnson, Alan

2004-03-01

Electron doping of semiconducting single-walled carbon nanotubes (SWNTs) by the thyroid hormone triiodothyronine (T3) is observed. T3 is applied locally, in solution, to SWNT field effect transistors (FETs) and binds along the length of the nanotube. T3 acts as an electron donor, shifting the I-V gate characteristics towards negative values of gate voltage. Shifts in the characteristics are measured as a function of the concentration of the solution. The effect is nearly reversible by rinsing the FETs with the solvent. Several days after application of T3, with no solvent rinsing, the gate characteristics are also nearly reversed. Experiments with a similar molecule for which the phenol ring is brominated as well as experiments with the de-iodinated molecule (T0) are performed to inform the effect of the iodine. The interaction of T3 with SWNTs may suggest a electronic interaction of T3 with other one-dimensional systems such as DNA.

Evaluation of experimental transection and partial excision of the caudal cruciate ligament in dogs.

PubMed

Harari, J; Johnson, A L; Stein, L E; Kneller, S K; Pijanowski, G

1987-01-01

The caudal cruciate ligament (CaCL) of one stifle joint in seven dogs was transected and a 2 to 4 mm section was removed. Six months after surgery, none of the dogs were lame. Thigh muscle circumference, stifle range of motion, and internal tibial rotation in the operated limb were not significantly different from the preoperative measurements or the contralateral, unoperated limb. A caudal drawer motion was consistently present in the stifle joints with a transected CaCL. A radiographic evaluation of the operated stifle joints did not reveal osteoarthritic changes; four of seven stifle joints had an irregular fat pad 6 months after surgery. Results of a joint fluid analysis revealed a slight increase in synovial cells within treated stifle joints; inflammatory cells were not observed. The only gross morphologic change in stifle joints with a severed ligament was enlarged knobby remnants of the CaCL. Articular cartilage defects or osteophytes were not observed. Results of a histologic examination of the CaCL remnants revealed synovial cellular capping and intraligamentous fibroplasia. Based on a limited number of dogs, it was concluded that isolated transection of the CaCL produced minimal clinical and pathologic changes in the stifle joint during a 6 month period.

Oligomeric stability of Rapana venosa hemocyanin (RvH) and its structural subunits.

PubMed

Dolashka-Angelova, Pavlina; Schwarz, Heinz; Dolashki, Aleksandar; Stevanovic, Stefan; Fecker, Miriam; Saeed, Muhammad; Voelter, Wolfgang

2003-03-21

The two structural subunits RvH1 and RvH2 were separated after overnight dialysis of Rapana venosa Hc against 130 mM Gly/NaOH buffer, pH 9.6, on an ion exchange column Hiload 26/10 Sepharose Q using a fast performance liquid chromatography (FPLC) system. The reassociation characteristics of these two RvH isoforms and the native molecule were studied in buffers with different pH values and concentrations of Ca(2+) and Mg(2+). Reassociation of mixed RvH subunits was performed over a period of several days using a stabilizing buffer (SB) of pH 7.0 containing different concentrations of Ca(2+) and Mg(2+) ions. After 2 days of dialysis, an RvH subunit mixture of didecamers and multidecamers was observed in the presence of 100 mM CaCl(2) and MgCl(2), though RvH1 and RvH2 are biochemically and immunologically different and have also different dissociation properties. The reassociation, performed at pH 9.6 with 2 mM CaCl(2) and MgCl(2) at 4 degrees C over a period of one to several weeks, led to the formation of decameric oligomers, while didecamers formed predominantly in the SB at pH 7.0. Higher concentrations of calcium and magnesium ions led to a more rapid reassociation of RvH1 resulting in long stable multidecamers and helical tubules, which were stable and slowly dissociated into shorter multidecamers and decamers at higher pH values. The reassociation of the RvH2 structural subunit in the same buffers processed slowly and yielded didecamers, shorter tubule polymers and long multidecamers which are less stable at higher pH values. The stability of RvH isoforms under varying ionic conditions is compared with the stability of keyhole limpet (KLH, Megathura crenulata) hemocyanin (KLH) and Haliotis tuberculata hemocyanin (HtH) isoforms. The process of dissociation and reassociation is connected with changes of the fluorescence intensity at 600 nm, which can be explained by differences in opalescence of the solutions of these two isoforms. The solutions of longer tubule polymers and multidecamers of RvH1 show a higher opalescence compared to the solutions of shorter helical tubules and multidecamers of RvH2.

Cellulose Nanofibrils and Mechanism of their Mineralization in Biomimetic Synthesis of Hydroxyapatite/Native Bacterial Cellulose Nanocomposites: Molecular Dynamics Simulations.

PubMed

Lukasheva, N V; Tolmachev, D A

2016-01-12

Molecular dynamics (MD) simulation of a nanofibril of native bacterial cellulose (BC) in solutions of mineral ions is presented. The supersaturated calcium-phosphate (CP) solution with the ionic composition of hydroxyapatite and CaCl2 solutions with the concentrations below, equal to, and above the solubility limits are simulated. The influence of solvation models (TIP3P and TIP4P-ew water models) on structural characteristics of the simulated nanofibril and on the crystal nucleation process is assessed. The structural characteristics of cellulose nanofibrils (in particular, of the surface layer) are found to be nearly independent of the solvation models used in the simulation and on the presence of ions in the solutions. It is shown that ionic clusters are formed in the solution rather than on the fibril surface. The cluster sizes are slightly different for the two water models. The effect of the ion-ion interaction parameters on the results is discussed. The main conclusion is that the activity of hydroxyl groups on the BC fibril surface is not high enough to cause adsorption of Ca(2+) ions from the solution. Therefore, the nucleation of CP crystals takes place initially in solution, and then the crystallites formed can be adsorbed on BC nanofibril surfaces.

In vitro cytoprotective effects of acetylsalicylic acid, carprofen, meloxicam, or robenacoxib against apoptosis induced by sodium nitroprusside in canine cruciate ligament cells.

PubMed

Waldherr, Katrin; Zurbriggen, Andreas; Spreng, David E; Forterre, Simone

2012-11-01

To determine whether incubation of cruciate ligament cells with acetylsalicylic acid, carprofen, meloxicam, or robenacoxib provides protection against apoptosis induced by sodium nitroprusside (SNP). Explants of cranial (CCL) and caudal (CaCL) cruciate ligaments from eight 1-day-old Beagles. Primary cultures of CCL and CaCL cells were created via enzymatic dissociation of cruciate explants. Purified cell cultures were incubated for 2 hours without (controls) or with 1 of 3 concentrations of 1 of 4 NSAIDs (10, 100, or 200 μg of acetylsalicylic acid/mL; 0.1, 1, or 10 μg of carprofen/mL; 0.1, 1, or 10 μg of meloxicam/mL; or 0.1, 1, or 10 μg of robenacoxib/mL) and subsequently incubated for 18 hours with 1 of 3 concentrations of SNP in an attempt to induce mild, moderate, or severe cytotoxic effects. Cell viability and apoptosis were analyzed via a cell proliferation assay and flow cytometry, respectively. Prostaglandin E(2) concentrations were measured via an ELISA. Cytoprotective effects of NSAIDs were dependent on the extent of SNP-induced apoptosis and were greatest in CCL and CaCL cell cultures with moderate SNP-induced cytotoxic effects. Preincubation with an NSAID improved cell viability by 15% to 45% when CCL and CaCL cells were subsequently incubated with SNP. Carprofen (10 μg/mL) had the greatest cytoprotective effects for CCL and CaCL cells. Incubation with NSAIDs resulted in a nonsignificant decrease in PGE(2) production from SNP-damaged cells. Results indicated that carprofen, meloxicam, and robenacoxib may reduce apoptosis in cells originating from canine cruciate ligaments.

Preparation and characterization of gellan gum microspheres containing a cold-adapted β-galactosidase from Rahnella sp. R3.

PubMed

Fan, Yuting; Yi, Jiang; Hua, Xiao; Zhang, Yuzhu; Yang, Ruijin

2017-04-15

R-β-Gal is a cold-adapted β-galactosidase that is able to hydrolyze lactose and has the potential to produce low-lactose or lactose-free dairy products at low temperatures (4°C). Cold-adapted enzymes unfold at moderate temperatures due to the lower intramolecular stabilizing interactions necessary for flexibility at low temperatures. To increase stability and usage-performance, R-β-Gal was encapsulated in gellan gum by injecting an aqueous solution into two different hardening solutions (10mM CaCl 2 or 10mM MgCl 2 ). Enzyme characteristics of both free and encapsulated R-β-Gal were carried out, and the different effects of two cations were investigated. R-β-Gal showed better thermal and pH stability after encapsulation. Ca 2+ gels had higher encapsulation efficiency (71.4%) than Mg 2+ (66.7%) gels, and Ca 2+ formed larger inner and surface pores. R-β-Gal was released from the Ca 2+ hydrogel beads more rapidly than the Mg 2+ hydrogels during storage in aqueous solution due to the larger inner/surface pores of the matrix. Copyright © 2017 Elsevier Ltd. All rights reserved.

Directed flow fluid rinse trough

DOEpatents

Kempka, Steven N.; Walters, Robert N.

1996-01-01

Novel rinse troughs accomplish thorough uniform rinsing. The tanks are suitable for one or more essentially planar items having substantially the same shape. The troughs ensure that each surface is rinsed uniformly. The new troughs also require less rinse fluid to accomplish a thorough rinse than prior art troughs.

The effectiveness of a preprocedural mouthrinse containing cetylpyridinium chloride in reducing bacteria in the dental office.

PubMed

Feres, Magda; Figueiredo, Luciene Cristina; Faveri, Marcelo; Stewart, Bernal; de Vizio, William

2010-04-01

During oral procedures, microorganisms from the oral cavity may contaminate nearby surfaces. The authors evaluated the efficacy of a commercial preprocedural mouthrinse containing 0.05 percent cetylpyridinium chloride (CPC) in reducing the levels and composition of viable bacteria in oral spatter. The authors randomly assigned 60 participants receiving oral prophylaxis with an ultrasonic scaler to one of four groups: a preprocedural rinse solution containing 0.05 percent CPC, 0.12 percent chlorhexidine (CHX) or water, or no rinsing. Airborne microorganisms were collected on blood agar plates. The composition of the spatter was analyzed for 39 oral bacterial species by means of checkerboard DNA-DNA hybridization. CPC and CHX were equally effective in lowering the levels of spatter bacteria and performed better than water and no rinsing (P < .05, Kruskal-Wallis test). The composition of the spatter from the control groups showed higher proportions (P < .05, Kruskal-Wallis test) of Fusobacterium species and lower proportions of Capnocytophaga species when compared with the spatter from the CPC and CHX groups. A commercial mouthrinse containing 0.05 percent CPC when used as a preprocedural mouthrinse was equally effective as CHX in reducing the levels of spatter bacteria generated during ultrasonic scaling. Owing to its strong antibacterial effect and the fact that it has fewer side effects than CHX, a solution containing 0.05 percent CPC may be a good alternative to that containing 0.12 CHX as a preprocedural mouthrinse used to help decrease the level of contamination in spatter.

Endodontic 'solutions' part 1: a literature review on the use of endodontic lubricants, irrigants and medicaments.

PubMed

Good, Melissa; El, Karim Ikhlas A; Hussey, David L

2012-05-01

Endodontic lubricants, irrigants and medicaments help prepare and disinfect root canal systems (RCS) but primary and secondary cases involve different microbes and therefore it is unlikely that one protocol will be effective for both case types. Each individual 'solution' or sequence of'solutions' could play a significant role in each case type, but there are no detailed published guidelines in existence. To help inform clinical practice it was decided to undertake a literature review followed by a UK and Republic of Ireland wide audit on current endodontic'solution' usage within dental schools. The literature review was undertaken under the following headings: pre-op oral rinse; file lubricants; root canal irrigants and intracanal medicaments and provides an evidence base for protocol development for both primary and retreatment cases.The audit project and the protocols developed from the findings of both the literature review and audit will be presented in Part 2.

Rinse trough with improved flow

DOEpatents

O'Hern, Timothy J.; Grasser, Thomas W.

1998-01-01

Novel rinse troughs accomplish thorough uniform rinsing. The troughs are suitable for one or more essentially planar objects having substantially the same shape. The troughs ensure that each surface is rinsed uniformly. The new troughs provide uniform rinse fluid flow over the objects' surfaces to accomplish a more thorough rinse than prior art troughs.

Directed flow fluid rinse trough

DOEpatents

Kempka, S.N.; Walters, R.N.

1996-07-02

Novel rinse troughs accomplish thorough uniform rinsing. The tanks are suitable for one or more essentially planar items having substantially the same shape. The troughs ensure that each surface is rinsed uniformly. The new troughs also require less rinse fluid to accomplish a thorough rinse than prior art troughs. 9 figs.

A 2-year in vitro evaluation of a chlorhexidine-containing acid on the durability of resin-dentin interfaces.

PubMed

Stanislawczuk, Rodrigo; Reis, Alessandra; Loguercio, Alessandro D

2011-01-01

This study evaluated the effect of 2% chlorhexidine-containing acid (Ac/CHX) and 2% chlorhexidine digluconate solution (CHX) on immediate (IM) and 2-year (2Y) resin-dentin bond strength (BS) and silver nitrate uptake (SNU) for two simplified etch-and-rinse adhesives. Forty-two caries-free extracted molars had a flat dentin surface exposed. In the control groups (groups 1), the surfaces were acid etched with conventional phosphoric acid and the adhesives Prime&Bond NT (PB) or Adper Single Bond 2 (SB) was applied after rinsing, drying and rewetting with water. In groups 2, Ac/CHX groups the adhesives were applied in a similar manner; however a 2% CHX-containing acid was previously applied. In groups 3, the adhesives were applied according to the control group; however the rewetting procedure was performed with an aqueous solution of 2% CHX for 60s. Composite build-ups were constructed incrementally and microtensile specimens (0.8mm(2)) were prepared for microtensile bond strength testing in the IM or 2Y periods at 0.5mm/min. For SNU, 2 bonded sticks from each tooth were coated with nail varnish, placed in the silver nitrate, polished down with SiC papers and analysed by EDX-SEM. The data from each adhesive was submitted to a two-way repeated measures ANOVA and Tukey's test (α=0.05). After 2Y, significant reductions of BS were observed for both adhesives in the control group (p<0.05). In Ac/CHX or CHX groups the BS remained stable for both systems. SNU was more evident in the control than in the experimental groups (p<0.05) both in IM and 2Y periods. The use of CHX in an aqueous solution or associated with the acid conditioner was effective to reduce the degradation of dentin bonds over a 2-year period. The addition of CHX digluconate in the acidic conditioner may be an excellent tool to increase the long-term stability of collagens fibrils within the hybrid layer against host-derived metalloproteinases without the need for additional steps for the bonding protocol. Copyright © 2010 Elsevier Ltd. All rights reserved.

Crystallization efficiencies of inorganic polyphosphate oligomers reacted with magnesium and calcium cations using anion-exchange chromatography with particulate formation-laser scattering detector.

PubMed

Ando, Masaki; Imadzu, Sakiyo; Kitagawa, Shinya; Ohtani, Hajime

2010-08-06

A particulate formation-laser scattering detector (PFLSD) was developed and used for evaluating the crystallization efficiency of inorganic polyphosphates (PPs) that reacted with either magnesium or calcium cations. As the solutions for reactive crystallization, 0.5 M ammonium buffer (pH 9.6) containing either 0.15 M MgCl(2) or 0.15 M CaCl(2) (MAP: magnesium ammonium phosphate and HAP: hydroxyapatite solution) were used. In the case of mono- and diphosphate (P1 and P2), the significant dependences of the particulate formation efficiency on various types of both P1/P2 and MAP/HAP reaction solutions were observed with the direct sample injection mode. The PFLSD was hyphenated with the anion-exchange chromatography and the dependence of the particulate formation efficiency on the polymerization degree (n(p)) of PP oligomers, separated chromatographically, was evaluated sequentially. The significant suppression of the particulate formation for PP oligomers was clearly confirmed, i.e., the MAP and HAP reaction solutions did not produce the particulates of the PP oligomers having an n(p) value of more than 3 and 5, respectively. As the overall tendency, the particulate formation efficiency in the case of the HAP solution was superior to that in the case of the MAP solution. Copyright 2010 Elsevier B.V. All rights reserved.

Normal and frictional interactions of purified human statherin adsorbed on molecularly-smooth solid substrata.

PubMed

Harvey, Neale M; Carpenter, Guy H; Proctor, Gordon B; Klein, Jacob

2011-09-01

Human salivary statherin was purified from parotid saliva and adsorbed to bare hydrophilic (HP) mica and STAI-coated hydrophobic (HB) mica in a series of Surface Force Balance experiments that measured the normal (F(n)) and friction forces (F(s)*) between statherin-coated mica substrata. Readings were taken both in the presence of statherin solution (HP and HB mica) and after rinsing (HP mica). F(n) measurements showed, for both substrata, monotonic steric repulsion that set on at a surface separation D ~20 nm, indicating an adsorbed layer whose unperturbed thickness was ca 10 nm. An additional longer-ranged repulsion, probably of electrostatic double-layer origin, was observed for rinsed surfaces under pure water. Under applied pressures of ~1 MPa, each surface layer was compressed to a thickness of ca 2 nm on both types of substratum, comparable with earlier estimates of the size of the statherin molecule. Friction measurements, in contrast with F(n) observations, were markedly different on the two different substrata: friction coefficients, μ ≡ ∂F(s)*/∂F(n), on the HB substratum (μ ≈ 0.88) were almost an order of magnitude higher than on the HP substratum (μ ≈ 0.09 and 0.12 for unrinsed and rinsed, respectively), and on the HB mica there was a lower dependence of friction on sliding speed than on the HP mica. The observations were attributed to statherin adsorbing to the mica in multimer aggregates, with internal re-arrangement of the protein molecules within the aggregate dependent on the substratum to which the aggregate adsorbed. This internal re-arrangement permitted aggregates to be of similar size on HP and HB mica but to have different internal molecular orientations, thus exposing different moieties to the solution in each case and accounting for the very different friction behaviour.

[Cleansing effect of two micromotor-driven endodontic handpieces.II. Effect of various rinsing solutions on the cleansing effect of the handpieces].

PubMed

Bartha, K; Rocca, J P

1993-12-01

The cleansing effectivity of citric acid solution was significantly better than that of Neomagnol both with respect to the removal of the Smear Layer (SL) and to the number of visible dentinal tubular orifices, however a complete elimination of the SL could not be obtained. Neomagnol seemed to be more effective in the removal of superficial debris and tissue-remnants.

First-Principles Study of Chemical Mixtures of CaCl2 and MgCl2 Hydrates for Optimized Seasonal Heat Storage

PubMed Central

2017-01-01

Chloride-based salt hydrates form a promising class of thermochemical materials (TCMs), having high storage capacity and fast kinetics. In the charging cycles of these hydrates however hydrolysis might appear along with dehydration. The HCl produced during the hydrolysis degrades and corrodes the storage system. Our GGA-DFT results show that the enthalpy charge during proton formation (an important step in hydrolysis) is much higher for CaCl2·2H2O (33.75 kcal/mol) than for MgCl2·2H2O (19.55 kcal/mol). This is a strong indicator that hydrolysis can be minimized by appropriate chemical mixing of CaCl2 and Mg Cl2 hydrates, which is also confirmed by recent experimental studies. GGA-DFT calculations were performed to obtain and analyze the optimized structures, charge distributions, bonding indicators and harmonic frequencies of various chemical mixtures hydrates and compared them to their elementary salts hydrates. We have further assessed the equilibrium products concentration of dehydration/hydrolysis of the chemical mixtures under a wide range of operating conditions. We observed that chemical mixing leads to an increase of the onset hydrolysis temperature with a maximum value of 79 K, thus increasing the resistance against hydrolysis with respect to the elementary salt hydrates. We also found that the chemical mixing of CaCl2 and MgCl2 hydrates widens the operating dehydration temperature range by a maximum value of 182 K (CaMg2Cl6·2H2O) and lowers the binding enthalpy with respect to the physical mixture by ≈65 kcal/mol for TCM based heat storage systems. PMID:28983386

Oxygen isotope activities and concentrations in aqueous salt solutions at elevated temperatures: Consequences for isotope geochemistry

USGS Publications Warehouse

Truesdell, A.H.

1974-01-01

Studies of the effect of dissolved salts on the oxygen isotope activity ratio of water have been extended to 275??C. Dehydrated salts were added to water of known isotope composition and the solutions were equilibrated with CO2 which was sampled for analysis. For comparison similar studies were made using pure water. Results on water nearly coincide with earlier calculations. Salt effects diminish with increasing temperature only for solutions of MgCl2 and LiCl. Other salt solutions show complex behavior due to the temperature-dependent formation of ion pairs of changing character. Equilibrium fractionations (103 ln ??) between 1 molal solutions and pure water at 25, 100, and 275??C are: NaCl 0.0, -1.5, +1.0; KCl 0.0, -1.0, +2.0; LiCl -1.0, -0.6, -0.5; CaCl2 -0.4, -1.8, +0.8; MgCl2 -1.1, -0.7, -0.3; MgSO4 -1.1, +0.1, -; NaF (0.8 m) 0.0, -1.5, -0.3; and NH4Cl (0.55 m) 0.0, -1.2, -1.3. These effects are significant in the isotope study of hot saline fluids responsible for ore deposition and of fluids found in certain geothermal systems. Minor modification of published isotope geothermometers may be required. ?? 1974.

Rinse trough with improved flow

DOEpatents

O`Hern, T.J.; Grasser, T.W.

1998-08-11

Novel rinse troughs accomplish thorough uniform rinsing. The troughs are suitable for one or more essentially planar objects having substantially the same shape. The troughs ensure that each surface is rinsed uniformly. The new troughs provide uniform rinse fluid flow over the objects` surfaces to accomplish a more thorough rinse than prior art troughs. 5 figs.

Fifteen-Year Survival of Endoscopic Anterior Cruciate Ligament Reconstruction in Patients Aged 18 Years and Younger.

PubMed

Morgan, Matthew D; Salmon, Lucy J; Waller, Alison; Roe, Justin P; Pinczewski, Leo A

2016-02-01

The current body of literature surrounding anterior cruciate ligament (ACL) survival and the variables contributing to further ACL injuries after primary ACL reconstruction in children and adolescents is limited, with no long-term evidence examining the incidence and contributing factors of further ACL injuries in this younger patient population. To determine the long-term survival of the ACL graft and the contralateral ACL (CACL) after primary reconstruction in patients aged ≤18 years and to identify the factors that increase the odds of subsequent ACL injuries. Case series; Level of evidence, 4. Patients having undergone primary ACL reconstruction at age ≤18 years between 1993 and 1998 who were included in a prospective database by a single surgeon were considered for this study. Single-incision endoscopic ACL reconstruction was performed with either an autologous bone-patellar tendon-bone graft or a hamstring tendon graft. At a minimum of 15 years after ACL reconstruction, patients completed a subjective survey involving the International Knee Documentation Committee (IKDC) questionnaire in addition to questions regarding current symptoms, further ACL injuries, family history of ACL injury, and current level of activity. A total of 288 adolescents (age range, 13-18 years) met the inclusion criteria, of whom 242 (84%) were reviewed at a mean of 16 years and 6 months after ACL reconstruction. Of these patients, 75 (31%) sustained a further ACL injury: 27 (11.2%) suffered an ACL graft rupture, 33 suffered a CACL injury (13.6%), and 15 sustained both an ACL graft rupture and a CACL injury (6.2%) over 15 years. Survival of the ACL graft was 95%, 92%, 88%, 85%, and 83% at 1, 2, 5, 10, and 15 years, respectively, and survival of the CACL was 99%, 98%, 90%, 83%, and 81%, respectively. Survival of the ACL graft was less favorable in those with a family history of ACL injury than in those without a family history (69% vs 90%, respectively; hazard ratio [HR], 3.6; P = .001). Survival of the CACL was less favorable in male patients than in female patients (75% vs 88%, respectively; HR, 2.1; P = .03) and in those who returned to competitive team ball sports than in those who did not (78% vs 89%, respectively; HR, 2.3; P = .05). After ACL reconstruction in patients aged ≤18 years, a further ACL injury occurred in 1 in 3 patients over 15 years. The 15-year survival rate of the ACL graft was 83%, and the 15-year survival rate of the CACL was 81%. The ACL graft and CACL were most vulnerable within the first 5 years after index surgery. A family history of ACL rupture significantly increased the risk for ACL graft ruptures, and a CACL injury was more common in male patients and those who returned to team ball sports. High IKDC scores and continued participation in sports were maintained over the long term after ACL reconstruction in the adolescent population. © 2016 The Author(s).

α-keratin/Alginate Biosorbent for Removal of Methylene Blue on Aqueous Solution in a Batch System

NASA Astrophysics Data System (ADS)

Fadillah, G.; Putri, E. N. K.; Febrianastuti, S.; Munawaroh, H.; Purnawan, C.; Wahyuningsih, S.

2018-03-01

Methylene Blue (MB) is a cationic dyes which is commonly used in textile industries for coloring agent. The precence of MB in water caused some negative effect on the environment and human health. Many common technologies such as membrane filtration, electrophoresis and adsorption have been widely empolyed for removal of MB in water, but the adsorption technique still has advantages than the others. In this study, removal of MB used a biosorbent α-keratin/alginate (KA). The biosorbent KA was prepared by using the encapsulation technique in CaCl2 2 % (w/v) solution. The biosorbent was characterized by Fourier Transform Infrared (FTIR) and Scanning Electron Microscope (SEM). The effect of composition of α-keratin and alginate, the pH of solution and contact time on the adsorption were investigated. The optimum adsorption of MB in aqueous solution was found at the composition of α-keratin and alginate of 1:2 (w/w), the pH at 5.0 and contact time at 4 hours. The adsorption of MB on KA biosorbent was comparatively higher than α-keratin and alginate only. Adsorption of MB dyes in aqueous solution followed the Langmuir adsorption isotherm, and the dynamic adsorption model could be described through a pseudo-second order kinetics.

Substrate Induced Ordering of Molecular Absorbates on Au(111)

DTIC Science & Technology

1992-02-27

the right in Fig.1), crossing, apparently unperturbed, monoatomic steps (not shown here). In addition, line pairs are organized in domains, separated...following immersion of a gold -electrode in a DMF solution containing I(x=5) and after rinsing with acetone; and, 4) a detailed STM investigation of the

Effect of simulated sanitizer carryover on recovery of salmonella from broiler carcass rinsates

USDA-ARS?s Scientific Manuscript database

Numerous antimicrobial chemicals are currently utilized as processing aids with the aim of reducing pathogenic bacteria on processed poultry carcasses. Carry-over of active sanitizer to a carcass rinse solution intended for detection of viable pathogenic bacteria by regulatory agencies may cause fal...

40 CFR Appendix C to Part 438 - Metal-Bearing Operations Definitions

Code of Federal Regulations, 2011 CFR

2011-07-01

... chromium. (1) In phosphate conversion, coatings are applied for one or more of the following reasons: to... electrolysis. The part is one of the electrodes and the electrolyte is usually alkaline. Electrolytic alkaline... during salt bath descaling includes spent process solutions, quenches, and rinses. Shot Tower—Lead Shot...

40 CFR Appendix C to Part 438 - Metal-Bearing Operations Definitions

Code of Federal Regulations, 2014 CFR

2014-07-01

... chromium. (1) In phosphate conversion, coatings are applied for one or more of the following reasons: to... electrolysis. The part is one of the electrodes and the electrolyte is usually alkaline. Electrolytic alkaline... during salt bath descaling includes spent process solutions, quenches, and rinses. Shot Tower—Lead Shot...

40 CFR Appendix C to Part 438 - Metal-Bearing Operations Definitions

Code of Federal Regulations, 2013 CFR

2013-07-01

... chromium. (1) In phosphate conversion, coatings are applied for one or more of the following reasons: to... electrolysis. The part is one of the electrodes and the electrolyte is usually alkaline. Electrolytic alkaline... during salt bath descaling includes spent process solutions, quenches, and rinses. Shot Tower—Lead Shot...

40 CFR Appendix C to Part 438 - Metal-Bearing Operations Definitions

Code of Federal Regulations, 2010 CFR

2010-07-01

... chromium. (1) In phosphate conversion, coatings are applied for one or more of the following reasons: to... electrolysis. The part is one of the electrodes and the electrolyte is usually alkaline. Electrolytic alkaline... during salt bath descaling includes spent process solutions, quenches, and rinses. Shot Tower—Lead Shot...

40 CFR Appendix C to Part 438 - Metal-Bearing Operations Definitions

Code of Federal Regulations, 2012 CFR

2012-07-01

... chromium. (1) In phosphate conversion, coatings are applied for one or more of the following reasons: to... electrolysis. The part is one of the electrodes and the electrolyte is usually alkaline. Electrolytic alkaline... during salt bath descaling includes spent process solutions, quenches, and rinses. Shot Tower—Lead Shot...

Binge drinking disturbs hepatic microcirculation after transplantation: prevention with free radical scavengers.

PubMed

Zhong, Z; Arteel, G E; Connor, H D; Schemmer, P; Chou, S C; Raleigh, J A; Mason, R P; Lemasters, J J; Thurman, R G

1999-08-01

Disturbances in hepatic microcirculation increase graft injury and failure; therefore, this study evaluates the effects of ethanol on microcirculation after liver transplantation. Donor rats were given one dose of ethanol (5 g/kg) by gavage 20 h before explantation, and grafts were stored in University of Wisconsin solution for 24 h before implantation. Acute ethanol treatment decreased 7-day survival of grafts from about 90 to 30%, increased transaminase release nearly 4-fold, and decreased bile production by 60%. Moreover, portal pressure increased significantly and liver surface oxygen tension decreased about 50%, indicating that ethanol disturbs hepatic microcirculation. Pimonidazole, a 2-nitroimidazole hypoxia marker, was given i.v. to recipients 30 min after implantation, and grafts were harvested 1 h later. Ethanol increased hepatic pimonidazole binding about 3-fold, indicating that ethanol led to hypoxia in fatty grafts. Ethanol also significantly increased free radicals in bile. Catechin (30 mg/kg i.v. upon reperfusion), a free radical scavenger, and Carolina Rinse solution, which contains several agents that inhibit free radical formation, minimized disturbances in microcirculation and prevented pimonidazole adduct formation significantly. These treatments also blunted increases in transaminase release and improved survival of fatty grafts. Destruction of Kupffer cells with GdCl(3) (20 mg/kg i.v. 24 h before explantation) or inhibition of formation of leukotrienes with MK-886 (50 microM in University of Wisconsin or rinse solution) also minimized hypoxia and improved survival after transplantation. Taken together, these results demonstrate that ethanol disturbs hepatic microcirculation, leading to graft hypoxia after transplantation, most likely by activating Kupffer cells and increasing free radical production.

Modeling the Onset of Phase Separation in CaO-SiO2-CaCl2 Chlorine-Containing Silicate Glasses.

PubMed

Swansbury, Laura A; Mountjoy, Gavin; Chen, Xiaojing; Karpukhina, Natalia; Hill, Robert

2017-06-08

The addition of chlorine into a bioactive glass composition is expected to reduce its abrasiveness and increase its bioactivity, which is important for dental applications such as toothpastes. There is a lack of information and understanding regarding the structural role of chlorine in chlorine-containing bioactive silicate glasses. This has prompted classical core-shell model molecular dynamics simulations of (50 - x/2)CaO-(50 - x/2)SiO 2 -xCaCl 2 glasses to be performed, where x ranges from x = 0.0 to 43.1 mol % CaCl 2 . These ternary glasses are advantageous for a fundamental study because they do not have additional network formers (e.g., phosphorus pentoxide) or modifiers (e.g., sodium) typically found in bioactive glass compositions. The (50 - x/2)CaO-(50 - x/2)SiO 2 -xCaCl 2 glasses were seen to become phase-separated around the x = 16.1 mol % CaCl 2 composition, and chlorine predominantly coordinated with calcium. These findings provide a solid foundation for further computational modeling work on more complex chlorine-containing bioactive glass compositions.

Statistical evaluation of nutritional components impacting phycocyanin production Synechocystis SP.

PubMed Central

Deshmukh, Devendra V.; Puranik, Pravin R.

2012-01-01

Alkaliphilic cyanobacterial cultures were isolated from Lonar lake (MS, India). Among the set of cultures, Synechocystis sp, was studied for phycocyanin production. A maximum yield was obtained in BG-11 medium at optimized conditions (pH 10 and 16 h light). In order to increase the phycocyanin yield media optimization based on the eight media components a Plackett-Burman design of the 12 experimental trials was used. As per the analysis CaCl2, 2H2O and Na2CO3 have been found to be the most influencing media components at 95% significance. Further the optimum concentrations of these components were estimated following a Box Wilson Central Composite Design (CCD) with four star points and five replicates at the center points for each of two factors was adopted for optimization of these two media components. The results indicated that there was an interlinked influence of CaCl2, 2H2O and Na2CO3 on 98% significance. The maximum yield of phycocyanin (12% of dry wt) could be obtained at 0.058 g/l and 0.115 g/l of CaCl2, 2H2O and Na2CO3, respectively. PMID:24031838

Fabrication of large size alginate beads for three-dimensional cell-cluster culture

NASA Astrophysics Data System (ADS)

Zhang, Zhengtao; Ruan, Meilin; Liu, Hongni; Cao, Yiping; He, Rongxiang

2017-08-01

We fabricated large size alginate beads using a simple microfluidic device under a co-axial injection regime. This device was made by PDMS casting with a mold formed by small diameter metal and polytetrafluorothylene tubes. Droplets of 2% sodium alginate were generated in soybean oil through the device and then cross-linked in a 2% CaCl2 solution, which was mixed tween80 with at a concentration of 0.4 to 40% (w/v). Our results showed that the morphology of the produced alginate beads strongly depends on the tween80 concentration. With the increase of concentration of tween80, the shape of the alginate beads varied from semi-spherical to tailed-spherical, due to the decrease of interface tension between oil and cross-link solution. To access the biocompatibility of the approach, MCF-7 cells were cultured with the alginate beads, showing the formation of cancer cells clusters which might be useful for future studies.

Speciation of Se and DOC in soil solution and their relation to Se bioavailability.

PubMed

Weng, Liping; Vega, Flora Alonso; Supriatin, Supriatin; Bussink, Wim; Van Riemsdijk, Willem H

2011-01-01

A 0.01 M CaCl(2) extraction is often used to asses the bioavailability of plant nutrients in soils. However, almost no correlation was found between selenium (Se) in the soil extraction and Se content in grass. The recently developed anion Donnan membrane technique was used to analyze chemical speciation of Se in the 0.01 M CaCl(2) extractions of grassland soils and fractionation of DOC (dissolved organic carbon). The results show that most of Se (67-86%) in the extractions (15 samples) are colloidal-sized Se. Only 13-34% of extractable Se are selenate, selenite and small organic Se (<1 nm). Colloidal Se is, most likely, Se bound to or incorporated in colloidal-sized organic matter. The dominant form of small Se compounds (selenate, selenite/small organic compounds) depends on soil. A total of 47-85% of DOC is colloidal-sized and 15-53% are small organic molecules (<1 nm). In combination with soluble S (sulfur) and/or P (phosphor), concentration of small DOC can explain most of the variability of Se content in grass. The results indicate that mineralization of organic Se is the most important factor that controls Se availability in soils. Competition with sulfate and phosphate needs to be taken into account. Further research is needed to verify if concentration of small DOC is a good indicator of mineralization of soil organic matter.

Study of the physical properties of calcium alginate hydrogel beads containing vineyard pruning waste for dye removal.

PubMed

Vecino, X; Devesa-Rey, R; Cruz, J M; Moldes, A B

2015-01-22

In this work the morphological and surface properties of a biocomposite formulated with vineyard pruning waste entrapped in calcium alginate hydrogel beads were studied. The formulation of the calcium alginate hydrogel beads, containing vineyard pruning waste, was based on the capacity of this green adsorbent to remove dye compounds from wastewater, observing that in the optimum condition (1.25% of cellulosic residue, 2.2% of sodium alginate and 0.475 mol L(-1) CaCl2) the percentage of dyes was reduced up to 74.6%. At lower concentration of CaCl2, high-resolution optical images show that the elongation of the vineyard-alginate biocomposite decreased, whereas the compactness increased. Moreover, higher concentrations of cellulosic residue increased the biocomposite roundness in comparison with biocomposite without the cellulosic residue. Interferometric perfilometry analysis (Ra, Rq, Rz and Rt) revealed that high concentrations of CaCl2 increased the roughness of the of the calcium alginate hydrogel beads observing vesicles in the external surface. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preparation of Ferrotitanium Alloys by Electrolysis-Assisted Calciothermic Reduction of Ilmenite in Equimolar CaCl2-NaCl Electrolyte: Effect of Calcium Oxide

NASA Astrophysics Data System (ADS)

Zhou, Zhongren; Zhang, Yingjie; Hua, Yixin; Xu, Cunying; Dong, Peng; Zhang, Qibo; Wang, Ding

2018-04-01

The effect of CaO content on the preparation of ferrotitanium alloys from ilmenite with the method of the electrolysis-assisted calciothermic reduction has been investigated by use of ilmenite powders as raw materials that positions them next to the cathodic molybdenum plate, equimolar CaCl2-NaCl molten salt with 2-7 mol.% CaO as electrolyte and graphite as anode at 700°C with cell voltage of 2.8 V under argon atmosphere. It is demonstrated that increasing the reactant CaO content is beneficial to the calciothermic reduction of ilmenite and the intermediate CaTiO3. Experimental results also show that after 14 h of calciothermic reduction process, the products are ferrotitanium alloys and the specific energy consumption is only about 10.21 kWh kg-1 when adding 5 mol.% CaO into equimolar CaCl2-NaCl molten salt and approximately 14.40 kWh kg-1 when CaO content is increased to 7 mol.%.

Granular Activated Carbon (GAC) System Performance Capabilities and Optimization

DTIC Science & Technology

1987-02-27

HMX 2,4-DNT Synthetic 4-component 73.4 27.7 5.76 0.939 (final analysis after aging 59.0 23.1 4.53 0.763 3 months) Actual AAP pink water 49.4 22.0 4.02...were used, stoppered with rubber stoppers wrapped in aluminum foil. Before each test, the flasks were washed in laboratory cleaning solution, rinsed with...Glass beads were used to eliminate excess "dead" volume. The ends of the glass tube were fitted with one-hole rubber stoppers and a short length of

Development of a model system for the study of spoilage associated secondary cucumber fermentation during long-term storage.

PubMed

Franco, Wendy; Pérez-Díaz, Ilenys M

2012-10-01

Calcium chloride fermentations represent an alternative to reduce chloride concentrations in the wastewaters generated from commercial cucumber fermentations, currently performed in cover brine solutions containing 6% to 12% sodium chloride. However, preliminary attempts to commercially ferment the cucumbers in the presence of oxygen led to the development of a secondary cucumber fermentation or spoilage. The development of cucumber secondary fermentation has also been occasionally reported by processors using cover brine solutions containing sodium chloride. This study focused on the development of a model system to characterize CaCl(2) and NaCl secondary cucumber fermentations under conditions similar to those present on the commercial scale. Cucumber fruits mixed with cover brine solutions, containing 100 mM CaCl(2) or 1.03 M NaCl, and 25 mM acetic acid, were fermented in 2 L fermentation vessels subjected to air-purging at a rate of 5 mL/min. Microorganisms and selected biochemical changes detected in the experimental cucumber fermentations had been previously observed in commercial spoilage samples, suggesting the successful reproduction of the secondary fermentation in the laboratory. Experimental secondary fermentations were characterized by the rapid oxidation of the lactic acid produced during the primary fermentation, which, in turn, increased pH. Lactic acid disappearance seemed to be the result of yeast metabolism that also led to the chemical reduction of the environment to levels at which other bacteria could become established and produce butyric, propionic, and acetic acids. This model system will be applied for the identification of strategies to prevent the initiation of the cucumber secondary fermentation and reduce economic losses in the pickling industry. The study of secondary cucumber fermentation has represented a challenge for many years. The successful development of a model system for the study of this phenomenon in the laboratory is instrumental in furthering the study of the event and in optimizing the sodium-chloride-free fermentation at the commercial scale. Journal of Food Science © 2012 Institute of Food Technologists® No claim to original US government works.

A molecular dynamic study on the dissociation mechanism of SI methane hydrate in inorganic salt aqueous solutions.

PubMed

Xu, Jiafang; Chen, Zhe; Liu, Jinxiang; Sun, Zening; Wang, Xiaopu; Zhang, Jun

2017-08-01

Gas hydrate is not only a potential energy resource, but also almost the biggest challenge in oil/gas flow assurance. Inorganic salts such as NaCl, KCl and CaCl 2 are widely used as the thermodynamic inhibitor to reduce the risk caused by hydrate formation. However, the inhibition mechanism is still unclear. Therefore, molecular dynamic (MD) simulation was performed to study the dissociation of structure I (SI) methane hydrate in existence of inorganic salt aqueous solution on a micro-scale. The simulation results showed that, the dissociation became stagnant due to the presence of liquid film formed by the decomposed water molecules, and more inorganic ions could shorten the stagnation-time. The diffusion coefficients of ions and water molecules were the largest in KCl system. The structures of ion/H 2 O and H 2 O/H 2 O were the most compact in hydrate/NaCl system. The ionic ability to decompose hydrate cells followed the sequence of: Ca 2+ >2K + >2Cl - >2Na + . Copyright © 2017 Elsevier Inc. All rights reserved.

Safety and Efficacy of a Mouth-Rinse with Granulocyte Colony Stimulating Factor in Patients with Chemotherapy-Induced Oral Mucositis.

PubMed

Wang, Lin; Huang, Xin-En; Ji, Zhu-Qing; Liu, Meng-Yan; Qian, Ting; Li, Li

2016-01-01

To assess the safety and effectiveness of a mouth-rinse with G-CSF (JiSaiXin, produced by NCPC Biotechnology Co., Ltd) in treating patients with chemotherapy-induced oral mucositis (CIM). A consecutive cohort of patients with advanced cancers and CIM were treated with mouth-rinse G-CSF. All chemotherapy for patients with advanced cancers was adopted from regimens suggested by NCCN guidelines. The mouth-rinse with G-CSF at a dose of 150-300ug plus 100ml-500ml normal saline was started from the time of oral mucositis was confirmed and continuously used for at least 7 days as one course. After at least two courses of treatment, safety and efficacy were evaluated. There were 7 female and 7 male patients with advanced cancer and CIM recruited into this study, including 5 with colorectal, 2 with lung, 1 patient with gastric, 1 with cervical and 1 with pancreatic cancer, as well as 2 patients with diffuse large B cell lymphomas, 1 with nasopharyngeal and 1 with gastric cancer. The median age was 57 (41-79) years. Grade 1 to 2 myelosuppression was observed in 3/14 patients, and Grade 4 myelosuppression in 1/14. Adverse effects on the gastrointestinal tract were documented in 5/14 patients, and were Grade 1 to Grade 3. No treatment related death was documented. Regarding CIM, the median response time to mouth rinse of G-CSF was 2 (1-5) days, and all patients with CIM demonstrated a positive response. Mouth-rinse with G-CSF proved to be safe and effective in treating patients with advanced cancers and CIM. However, further randomized controlled studies should be conducted to clarify the effectiveness of this treatment with other lesions.

Loss of MURC/Cavin-4 induces JNK and MMP-9 activity enhancement in vascular smooth muscle cells and exacerbates abdominal aortic aneurysm.

PubMed

Miyagawa, Kotaro; Ogata, Takehiro; Ueyama, Tomomi; Kasahara, Takeru; Nakanishi, Naohiko; Naito, Daisuke; Taniguchi, Takuya; Hamaoka, Tetsuro; Maruyama, Naoki; Nishi, Masahiro; Kimura, Taizo; Yamada, Hiroyuki; Aoki, Hiroki; Matoba, Satoaki

2017-06-03

Abdominal aortic aneurysm (AAA) is relatively common in elderly patients with atherosclerosis. MURC (muscle-restricted coiled-coil protein)/Cavin-4 modulating the caveolae function of muscle cells is expressed in cardiomyocytes, skeletal muscle cells and smooth muscle cells. Here, we show a novel functional role of MURC/Cavin-4 in vascular smooth muscle cells (VSMCs) and AAA development. Both wild-type (WT) and MURC/Cavin-4 knockout (MURC -/- ) mice subjected to periaortic application of CaCl 2 developed AAAs. Six weeks after CaCl 2 treatment, internal and external aortic diameters were significantly increased in MURC -/- AAAs compared with WT AAAs, which were accompanied by advanced fibrosis in the tunica media of MURC -/- AAAs. The activity of JNK and matrix metalloproteinase (MMP) -2 and -9 were increased in MURC -/- AAAs compared with WT AAAs at 5 days after CaCl 2 treatment. At 6 weeks after CaCl 2 treatment, MURC -/- AAAs exhibited attenuated JNK activity compared with WT AAAs. There was no difference in the activity of MMP-2 or -9 between saline and CaCl 2 treatments. In MURC/Cavin-4-knockdown VSMCs, TNFα-induced activity of JNK and MMP-9 was enhanced compared with control VSMCs. Furthermore, WT, MURC -/- , apolipoprotein E -/- (ApoE -/- ), and MURC/Cavin-4 and ApoE double-knockout (MURC -/- ApoE -/- ) mice were subjected to angiotensin II (Ang II) infusion. In both ApoE -/- and MURC -/- ApoE -/- mice infused for 4 weeks with Ang II, AAAs were promoted. The internal aortic diameter was significantly increased in Ang II-infused MURC -/- ApoE -/- mice compared with Ang II-infused ApoE -/- mice. In MURC/Cavin-4-knockdown VSMCs, Ang II-induced activity of JNK and MMP-9 was enhanced compared with control VSMCs. Our results suggest that MURC/Cavin-4 in VSMCs modulates AAA progression at the early stage via the activation of JNK and MMP-9. MURC/Cavin-4 is a potential therapeutic target against AAA progression. Copyright © 2017 Elsevier Inc. All rights reserved.

Mobility of arsenic and its compounds in soil and soil solution: the effect of soil pretreatment and extraction methods.

PubMed

Száková, J; Tlustos, P; Goessler, W; Frková, Z; Najmanová, J

2009-12-30

The effect of soil extraction procedures and/or sample pretreatment (drying, freezing of the soil sample) on the extractability of arsenic and its compounds was tested. In the first part, five extraction procedures were compared with following order of extractable arsenic portions: 2M HNO(3)>0.43 M CH(3)COOH>or=0.05 M EDTA>or=Mehlich III (0.2M CH(3)COOH+0.25 M NH(4)NO(3)+0.013 M HNO(3)+0.015 M NH(4)F+0.001 M EDTA) extraction>water). Additionally, two methods of soil solution sampling were compared, centrifugation of saturated soil and the use of suction cups. The results showed that different sample pretreatments including soil solution sampling could lead to different absolute values of mobile arsenic content in soils. However, the interpretation of the data can lead to similar conclusions as apparent from the comparison of the soil solution sampling methods (r=0.79). For determination of arsenic compounds mild extraction procedures (0.05 M (NH(4))(2)SO(4), 0.01 M CaCl(2), and water) and soil solution sampling using suction cups were compared. Regarding the real soil conditions the extraction of fresh samples and/or in situ collection of soil solution are preferred among the sample pretreatments and/or soil extraction procedures. However, chemical stabilization of the solutions should be allowed and included in the analytical procedures for determination of individual arsenic compounds.

Demonstration and Validation of a Regenerated-Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground Water Quality and Remediation Progress at DoD Sites

DTIC Science & Technology

2007-01-01

ethanol, sodium benzoate , and ethylene diamine tetra-acetic acid (EDTA). Alternatively, the membrane can be purchased dry, but then must be...cleaned in a series of steps that includes soaking and rinsing in deionized water, heated sodium bicarbonate solution, EDTA, and sodium azide solution to...Potassium Chromium Selenium Sodium Copper Vanadium Aluminum Iron Zinc Arsenic Lead Antimony Manganese Anions (1-3 days) Bicarbonate/Alkalinity

Interactions of PAMAM dendrimers with SDS at the solid-liquid interface.

PubMed

Arteta, Marianna Yanez; Eltes, Felix; Campbell, Richard A; Nylander, Tommy

2013-05-14

This work addresses structural and nonequilibrium effects of the interactions between well-defined cationic poly(amidoamine) PAMAM dendrimers of generations 4 and 8 and the anionic surfactant sodium dodecyl sulfate (SDS) at the hydrophilic silica-water interface. Neutron reflectometry and quartz crystal microbalance with dissipation monitoring were used to reveal the adsorption from premixed dendrimer/surfactant solutions as well as sequential addition of the surfactant to preadsorbed layers of dendrimers. PAMAM dendrimers of both generations adsorb to hydrophilic silica as a compact monolayer, and the adsorption is irreversible upon rinsing with salt solution. SDS adsorbs on the dendrimer layer and at low bulk concentrations causes the expansion of the dendrimer layers on the surface. When the bulk concentration of SDS is increased, the surfactant layer consists of aggregates or bilayer-like structures. The adsorption of surfactant is reversible upon rinsing, but slight changes of the structure of the preadsorbed PAMAM monolayer were observed. The adsorption from premixed solutions close to charge neutrality results in thick multilayers, but the surface excess is lower when the bulk complexes have a net negative charge. A critical examination of the pathway of adsorption for the interactions of SDS with preadsorbed PAMAM monolayers and premixed PAMAM/SDS solutions with hydrophilic silica revealed that nonequilibrium effects are important only in the latter case, and the application of a thermodynamic model to such experimental data would be inappropriate.

A Process Elaboration Formalism for Writing and Analyzing Programs

DTIC Science & Technology

1975-10-01

program is to be proved, a description of its (i) See [MANN 73] for a survey of these debugging tools, di) See [ELSPAS 72] for a complete review of this...öy the instructions which might be found on a shampoo bottle. 1) Wet hair 2) Lather 3) Rinse «) Repeat Statement 4, the source of the problem, *M...tor this simple aigonthm is shown m Figure 52. SHAMPOO WET-HAIR LATHER RINSE REPEAT - WET-HAIR -> LATHER -> RINSE -> REPEAT - (TCRMMAL "WE’T.’NG

In situ mineralization of hydroxyapatite on electrospun chitosan-based nanofibrous scaffolds.

PubMed

Yang, Dongzhi; Jin, Yu; Zhou, Yingshan; Ma, Guiping; Chen, Xiangmei; Lu, Fengmin; Nie, Jun

2008-03-10

A biocomposite of hydroxyapatite (HAp) with electrospun nanofibrous scaffolds was prepared by using chitosan/polyvinyl alcohol (CS/PVA) and N-carboxyethyl chitosan/PVA (CECS/PVA) electrospun membranes as organic matrix, and HAp was formed in supersaturated CaCl2 and KH2PO4 solution. The influences of carboxylic acid groups in CECS/PVA fibrous scaffold and polyanionic additive poly(acrylic acid) (PAA) in the incubation solution on the crystal distribution of the HAp were investigated. Field-emission scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS), wide-angle X-ray diffraction (WAXD), and Fourier transform infrared (FTIR) were used to characterize the morphology and structure of the deposited mineral phase on the scaffolds. It was found that addition of PAA to the mineral solution and use of matrix with carboxylic acid groups promoted mineral growth and distribution of HAp. MTT testing and SEM imaging from mouse fibroblast (L929) cell culture revealed the attachment and growth of mouse fibroblast on the surface of biocomposite scaffold, and that the cell morphology and viability were satisfactory for the composite to be used in bioapplications.

Encapsulated eucalyptus oil in ionically cross-linked alginate microcapsules and its controlled release.

PubMed

Noppakundilograt, Supaporn; Piboon, Phianghathai; Graisuwan, Wilaiporn; Nuisin, Roongkan; Kiatkamjornwong, Suda

2015-10-20

Sodium alginate microcapsules containing eucalyptus oil were prepared by oil-in-water emulsification via Shirasu porous glass (SPG) membrane and cross-linked by calcium chloride (CaCl2). SPG membrane pore size of 5.2μm was used to control the size of eucalyptus oil microdroplets. Effects of sodium alginate, having a mannuronic acid/guluronic acid (M/G) ratio of 1.13, eucalyptus oil and CaCl2 amounts on microdroplet sizes and size distribution were elucidated. Increasing sodium alginate amounts from 0.1 to 0.5% (wv(-1)) sodium alginate, the average droplets size increased from 42.2±2.0 to 48.5±0.6μm, with CVs of 16.5±2.2 and 30.2±4.5%, respectively. CaCl2 successfully gave narrower size distribution of cross-linked eucalyptus oil microcapsules. The optimum conditions for preparing the microcapsules, oil loading efficiency, and controlled release of the encapsulated eucalyptus oil from the microcapsules as a function of time at 40°C were investigated. Release model for the oil from microcapsules fitted Ritger-Peppas model with non-Fickian transport mechanism. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of various final irrigants on the shear bond strength of resin-based sealer to dentin

PubMed Central

Kandaswamy, Deivanayagam; Venkateshbabu, Nagendrababu; Arathi, Ganesh; Roohi, Riaz; Anand, Suresh

2011-01-01

Aim: This study has been designed to evaluate the effect of strong (MTAD) or soft (1- hydroxyethylidene – 1, 1-bisphosphonate (HEBP) final irrigating solution on the shear bond strength of AH plus sealer to coronal dentin. 17% EDTA was used as the reference. Materials and Methods: Forty freshly extracted human maxillary first premolars were prepared using different irrigation protocols (n=10). All the test groups had 1.3% NaOCl as initial rinse and followed by specific final rinse for each group: G1 – distilled water(control), G2 – 17% EDTA, G3- 18% HEBP and G4 – MTAD. Sections of polyethylene tubes that are 3mm long were filled with freshly mixed sealer and placed on the dentin surfaces. The bonding between the sealer and dentine surface was evaluated using shear bond testing. The values were statistically evaluated using one-way ANOVA followed by Tukey's test. Result: Significant difference was found among the irrigating regimes. EDTA showed highest bond strength followed by HEBP and MTAD PMID:21691504

Fluoride rinse effect on retention of CaF2 formed on enamel/dentine by fluoride application.

PubMed

Falcão, Amanda; Masson, Nadia; Leitão, Tarcísio Jorge; Botelho, Juliana Nunes; Ferreira-Nóbilo, Naiara de Paula; Tabchoury, Cínthia Pereira Machado; Tenuta, Livia Maria Andaló; Cury, Jaime Aparecido

2016-01-01

Calcium fluoride-like materials ("CaF2") formed on dental surfaces after professional fluoride application are unstable in the oral environment but can be retained longer with a daily NaF mouthrinse. We tested the effect of twice daily 0.05% NaF rinses on the retention of "CaF2" formed on enamel and dentine after applying acidulated phosphate fluoride (APF). "CaF2" formed on enamel/dentine by APF application significantly decreased after exposure to artificial saliva and the 0.05% NaF rinse was ineffective to avoid this reduction. These findings suggest that the combination of APF and 0.05% NaF is not clinically relevant, either for caries or dental hypersensitivity.

A Rinsing Effluent Evaporator for Dismantling Operations - 13271

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rives, Rachel; Asou-Pothet, Marielle; Chambon, Frederic

2013-07-01

Between 1958 and 1997, the UP1 plant at Marcoule - located in the south of France - reprocessed and recycled nearly 20,000 MT of used fuel from special defense applications reactors, as well as fuel from the first generation of electricity generating reactors in France (natural uranium fuel, CO{sub 2}-cooled, graphite-moderated). Decommissioning and Dismantling of the UP1 plant and its associated units started in 1998. Since 2005, the UP1 facility has been operated by AREVA as the Marcoule Management and Operation contractor for French Atomic Energy Commission (CEA). An important part of this decommissioning program deals with the vitrification facilitymore » of Marcoule. This facility includes 20 tanks devoted to interim storage of highly active solutions, prior to vitrification. In 2006, a rinsing program was defined as part of the tank cleanup strategy. The main objective of the rinsing phases was to decrease activity in order to limit the volume of 'long-life active' waste produced during the decommissioning operations, so the tanks can be dismantled without the need of remote operations. To enable this rinsing program, and anticipating large volumes of generated effluent, the construction of an evaporation unit proved to be essential. The main objective of this unit was to concentrate the effluent produced during tank rinsing operations by a factor of approximately 10, prior to it being treated by vitrification. The evaporator design phase was launched in September 2006. The main challenge for the Project team was the installation of this new unit within a nuclear facility still in operation and in existing compartments not initially designed for this purpose. Cold operating tests were completed in 2008, and in May 2009, the final connections to the process were activated to start the hot test phase. During the first hot test operations performed on the first batches of clean-up effluent, the evaporator had a major operating problem. Extremely large quantities of foam were produced, affecting the evaporator operation, and creating the risk of a reduction in its capacity and throughput performance. A task force of AREVA process, operations, and safety experts from Marcoule and the La Hague reprocessing complex was assembled. New operating parameters were defined and tested to improve the process. Since then, the evaporator has performed very satisfactorily. The foam buildup phenomenon has been brought under complete control. All the different types of effluents produced during cleanup operations have been concentrated, and the results obtained in terms of quality and throughput, have ensured a consistent supply to the vitrification unit. The evaporator was operated until the end of April 2012, and enabled the production of 500 cubic meters of very high activity effluent, concentrating the fission products rinsed from the storage tanks. The evaporator will now be deactivated and decommissioned, with the first rinsing and cleanup operations scheduled to begin in 2014. (authors)« less

The effect of compliance on contact lens case contamination.

PubMed

Tilia, Daniel; Lazon de la Jara, Percy; Zhu, Hua; Naduvilath, Thomas J; Holden, Brien A

2014-03-01

To determine the efficacy of written instructions on contact lens case hygiene and to quantify the effect of noncompliance on contact lens case contamination. Data were retrospectively analyzed from 16 prospective, 3-month daily-wear studies during which six commercially available silicone hydrogel contact lenses and seven lens care solutions (LCS) were tested following a similar protocol. Verbal instructions regarding case hygiene (rinse case with LCS, not tap water) were given in nine studies, while the same instructions were given verbally and in written format in seven studies. A survey on contact lens, LCS, and lens case hygiene was completed at 1- and 3-month visits and compliance with case hygiene instructions was determined. Regular contact lens cases were used for 1 month and collected for microbial analysis at the 1- and 3-month visits. The rate of case contamination and the types of microbes contaminating cases were evaluated. Participants given verbal and written instructions were more likely to be compliant with case hygiene instructions than those just given verbal instructions (odds ratio [OR]: 2.19, p < 0.001, 95% confidence interval [CI]: 1.40-3.44). The overall case contamination rate was 79%. Use of tap water to rinse contact lens cases was associated with significantly more cases contaminated with Gram-negative bacteria (GNB) (30% vs. 10%, p < 0.001), a greater risk of GNB case contamination (OR: 2.91, p < 0.001. 95% CI: 1.72-4.92), and a higher quantity of GNB in cases (mean colony-forming unit/case ± SD: 28,286 ± 131,935 vs. 6477 ± 60,447, p < 0.001). Lens case hygiene can be improved by effective communication of instructions. Contact lens wearers should be actively discouraged from rinsing contact lens cases with tap water because of the increased risk of GNB contamination.

Effect of an essential oil-containing mouth rinse on VSC-producing bacteria on the tongue.

PubMed

Thaweboon, Sroisiri; Thaweboon, Boonyanit

2011-03-01

The objective of the present study was to investigate the inhibitory effect of a commercially available essential oil-containing mouth rinse 12 hours after a single rinse and two weeks of twice daily rinsing, on volatile sulphur compounds (VSC) producing bacteria on the tongue. The study was a randomized, double-blind, controlled crossover design. Thirty-six healthy subjects, aged 20-48 years, volunteered to participate in the study. Subjects were randomly assigned to rinse twice daily with either an essential oil-containing mouth rinse (Cool Mint Listerine Antiseptic) or a negative control rinse. Bacteria samples were taken from the dorsum of the tongue at baseline, after the first rinse and two weeks later. They were plated on OOPS medium to enumerate the VSC-producing bacteria. Intergroup comparisons of log10 transformed colony-forming units of the samples were made using analysis of covariance. Each comparison was performed at a 5% significance level. The mean VSC-producing bacteria in subjects using the essential oil mouth rinse were significantly lower than those using the control rinse twice daily. In healthy subjects, rinsing with an essential oil-containing mouth rinse can have a significant effect on VSC-producing bacteria on the tongue and may be useful for controlling intrinsic oral malodor over prolonged periods.

A Thermodynamic Model for Predicting Mineral Reactivity in Supercritical Carbon Dioxide: I. Phase Behavior of Carbon Dioxide - Water - Chloride Salt Systems Across the H2O-Rich to the CO2-Rich Regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, Ronald D.; Wang, Zheming; Anderko, Andre

Phase equilibria in mixtures containing carbon dioxide, water, and chloride salts have been investigated using a combination of solubility measurements and thermodynamic modeling. The solubility of water in the CO2-rich phase of ternary mixtures of CO2, H2O and NaCl or CaCl2 was determined, using near infrared spectroscopy, at 90 atm and 40 to 100 °C. These measurements fill a gap in the experimental database for CO2 water salt systems, for which phase composition data have been available only for the H2O-rich phases. A thermodynamic model for CO2 water salt systems has been constructed on the basis of the previously developedmore » Mixed-Solvent Electrolyte (MSE) framework, which is capable of modeling aqueous solutions over broad ranges of temperature and pressure, is valid to high electrolyte concentrations, treats mixed-phase systems (with both scCO2 and water present) and can predict the thermodynamic properties of dry and partially water-saturated supercritical CO2 over broad ranges of temperature and pressure. Within the MSE framework the standard-state properties are calculated from the Helgeson-Kirkham-Flowers equation of state whereas the excess Gibbs energy includes a long-range electrostatic interaction term expressed by a Pitzer-Debye-Hückel equation, a virial coefficient-type term for interactions between ions and a short-range term for interactions involving neutral molecules. The parameters of the MSE model have been evaluated using literature data for both the H2O-rich and CO2-rich phases in the CO2 - H2O binary and for the H2O-rich phase in the CO2 - H2O - NaCl / KCl / CaCl2 / MgCl2 ternary and multicompontent systems. The model accurately represents the properties of these systems at temperatures from 0°C to 300 °C and pressures up to ~4000 atm. Further, the solubilities of H2O in CO2-rich phases that are predicted by the model are in agreement with the new measurements for the CO2 - H2O - NaCl and CO2 - H2O - CaCl2 systems. Thus, the model can be used to predict the effect of various salts on the water content and water activity in CO2-rich phases on the basis of parameters determined from the properties of aqueous systems. Given the importance of water activity in CO2-rich phases for mineral reactivity, the model can be used as a foundation for predicting mineral transformations across the entire CO2/H2O composition range from aqueous solution to anhydrous scCO2. An example application using the model is presented which involves the transformation of forsterite to nesquehonite as a function of temperature and water content in the CO2-rich phase.« less

Dust Effects on Nucleation Kinetics and Nanoparticle Product Size Distributions: Illustrative Case Study of a Prototype Ir(0)n Transition-Metal Nanoparticle Formation System.

PubMed

Özkar, Saim; Finke, Richard G

2017-07-05

The question is addressed if dust is kinetically important in the nucleation and growth of Ir(0) n nanoparticles formed from [Bu 4 N] 5 Na 3 (1,5-COD)Ir I ·P 2 W 15 Nb 3 O 62 (hereafter [(COD)Ir·POM] 8- ), reduced by H 2 in propylene carbonate solvent. Following a concise review of the (often-neglected) literature addressing dust in nucleation phenomena dating back to the late 1800s, the nucleation and growth kinetics of the [(COD)Ir·POM] 8- precatalyst system are examined for the effects of 0.2 μm microfiltration of the solvent and precatalyst solution, of rinsing the glassware with that microfiltered solvent, of silanizing the glass reaction vessel, for the addition of <0.2 μm γ-Al 2 O 3 (inorganic) dust, for the addition of flame-made carbon-based (organic) dust, and as a function of the starting, microfiltered [(COD)Ir·POM 8- ] concentration. Efforts to detect dust and its removal by dynamic light scattering and by optical microscopy are also reported. The results yield a list of eight important conclusions, the four most noteworthy of which are (i) that the nucleation apparent rate "constant" k 1obs(bimol) is shown to be slowed by a factor of ∼5 to ∼7.6, depending on the precise experiment and its conditions, just by the filtration of the precatalyst solution using a 0.20 μm filter and rinsing the glassware surface with 0.20 μm filtered propylene carbonate solvent; (ii) that simply employing a 0.20 μm filtration step narrows the size distribution of the resulting Ir(0) n nanoparticles by a factor of 2.4 from ±19 to ±8%, a remarkable result; (iii) that the narrower size distribution can be accounted for by the slowed nucleation rate constant, k 1obs(bimol) , and by the unchanged autocatalytic growth rate constant, k 2obs(bimol) , that is, by the increased ratio of k 2obs(bimol) /k 1obs(bimol) that further separates nucleation from growth in time for filtered vs unfiltered solutions; and (iv) that five lines of evidence indicate that the filterable component of the solution, which has nucleation rate-enhancing and size-dispersion broadening effects, is dust.

Japanese Papilio butterflies puddle using Na+ detected by contact chemosensilla in the proboscis

NASA Astrophysics Data System (ADS)

Inoue, Takashi A.; Hata, Tamako; Asaoka, Kiyoshi; Ito, Tetsuo; Niihara, Kinuko; Hagiya, Hiroshi; Yokohari, Fumio

2012-12-01

Many butterflies acquire nutrients from non-nectar sources such as puddles. To better understand how male Papilio butterflies identify suitable sites for puddling, we used behavioral and electrophysiological methods to examine the responses of Japanese Papilio butterflies to Na+, K+, Ca2+, and Mg2+. Based on behavioral analyses, these butterflies preferred a 10-mM Na+ solution to K+, Ca2+, and Mg2+ solutions of the same concentration and among a tested range of 1 mM to 1 M NaCl. We also measured the ion concentrations of solutions sampled from puddling sites in the field. Na+ concentrations of the samples were up to 6 mM, slightly lower than that preferred by butterflies in the behavioral experiments. Butterflies that sipped the 10 mM Na+ solution from the experimental trays did not continue to puddle on the ground. Additionally, butterflies puddled at sites where the concentrations of K+, Ca2+, and/or Mg2+ were higher than that of Na+. This suggests that K+, Ca2+, and Mg2+ do not interfere with the detection of Na+ by the Papilio butterfly. Using an electrophysiological method, tip recordings, receptor neurons in contact chemosensilla inside the proboscis evoked regularly firing impulses to 1, 10, and 100 mM NaCl solutions but not to CaCl2 or MgCl2. The dose-response patterns to the NaCl solutions were different among the neurons, which were classified into three types. These results showed that Japanese Papilio butterflies puddle using Na+ detected by the contact chemosensilla in the proboscis, which measure its concentration.

Intra-Amniotic Administration (Gallus gallus) of Cicer arietinum and Lens culinaris Prebiotics Extracts and Duck Egg White Peptides Affects Calcium Status and Intestinal Functionality

PubMed Central

Hou, Tao; Glahn, Raymond P.; Tako, Elad

2017-01-01

Calcium (Ca) is one of the most abundant inorganic elements in the human body and has many important physiological roles. Prebiotics and bioactive peptides are two important substances used to promote calcium uptake. However, the difference in mechanisms of the calcium uptake from these two supplements is not clear. By using the Gallus gallus model and the intra-amniotic administration procedure, the aim of this study was to investigate whether Ca status, intestinal functionality, and health-promoting bacterial populations were affected by prebiotics extracted from chickpea and lentil, and duck egg white peptides (DPs). Eleven groups (non-injected; 18 MΩ H2O; 4 mmol/L CaCl2; 50 mg/mL chickpea + 4 mmol/L CaCl2; 50 mg/mL lentil + 4 mmol/L CaCl2; 40 mg/mL DPs + 4 mmol/L CaCl2; 5 mg/mL Val-Ser-Glu-Glu (VSEE) + 4 mmol/L CaCl2; 50 mg/mL chickpea; 50 mg/mL lentil; 40 mg/mL DPs; 5 mg/mL VSEE) were utilized. Upon hatch, blood, cecum, small intestine, liver and bone were collected for assessment of serum bone alkaline phosphate level (BALP), the relative abundance of intestinal microflora, expression of Ca-related genes, brush border membrane (BBM) functional genes, and liver and bone mineral levels, respectively. The BALP level increased in the presence of lentil, DPs and VSEE (p < 0.05). The relative abundance of probiotics increased significantly (p < 0.05) by VSEE + Ca and chickpea. The expression of CalbindinD9k (Ca transporter) increased (p < 0.05) in Ca, chickpea + Ca and lentil + Ca groups. In addition, the brush border membrane functionality genes expressions increased (p < 0.05) by the chickpea or lentil extracts. Prebiotics and DPs beneficially affected the intestinal microflora and duodenal villus surface area. This research expands the understanding of the prebiotics’ properties of chickpea and lentil extracts, and peptides’ effects on calcium metabolism and gut health. PMID:28754012

Desorption of intrinsic cesium from smectite: inhibitive effects of clay particle organization on cesium desorption.

PubMed

Fukushi, Keisuke; Sakai, Haruka; Itono, Taeko; Tamura, Akihiro; Arai, Shoji

2014-09-16

Fine clay particles have functioned as transport media for radiocesium in terrestrial environments after nuclear accidents. Because radiocesium is expected to be retained in clay minerals by a cation-exchange reaction, ascertaining trace cesium desorption behavior in response to changing solution conditions is crucially important. This study systematically investigated the desorption behavior of intrinsic Cs (13 nmol/g) in well-characterized Na-montmorillonite in electrolyte solutions (NaCl, KCl, CaCl2, and MgCl2) under widely differing cation concentrations (0.2 mM to 0.2 M). Batch desorption experiments demonstrated that Cs(+) desorption was inhibited significantly in the presence of the environmental relevant concentrations of Ca(2+) and Mg(2+) (>0.5 mM) and high concentrations of K(+). The order of ability for Cs desorption was Na(+) = K(+) > Ca(2+) = Mg(2+) at the highest cation concentration (0.2 M), which is opposite to the theoretical prediction based on the cation-exchange selectivity. Laser diffraction grain-size analyses revealed that the inhibition of Cs(+) desorption coincided with the increase of the clay tactoid size. Results suggest that radiocesium in the dispersed fine clay particles adheres on the solid phase when the organization of swelling clay particles occurs because of changes in solution conditions caused by both natural processes and artificial treatments.

Inactivation of Salmonella Enteritidis on lettuces used by minimally processed vegetable industries.

PubMed

Silveira, Josete Bailardi; Hessel, Claudia Titze; Tondo, Eduardo Cesar

2017-01-30

Washing and disinfection methods used by minimally processed vegetable industries of Southern Brazil were reproduced in laboratory in order to verify their effectiveness to reduce Salmonella Enteritidis SE86 (SE86) on lettuce. Among the five industries investigated, four carried out washing with potable water followed by disinfection with 200 ppm sodium hypochlorite during different immersion times. The washing procedure alone decreased approximately 1 log CFU/g of SE86 population and immersion times of 1, 2, 5, and 15 minutes in disinfectant solution demonstrated reduction rates ranging from 2.06±0.10 log CFU/g to 3.01±0.21 log CFU/g. Rinsing alone was able to reduce counts from 0.12±0.63 log CFU/g to 1.90±1.07 log CFU/g. The most effective method was washing followed by disinfection with 200 ppm sodium hypochlorite for 15 minutes and final rinse with potable water, reaching 5.83 log CFU/g of reduction. However, no statistical differences were observed on the reduction rates after different immersion times. A time interval of 1 to 2 minutes may be an advantage to the minimally vegetable processed industries in order to optimize the process without putting at risk food safety.

Direct reduction processes for titanium oxide in molten salt

NASA Astrophysics Data System (ADS)

Suzuki, Ryosuke O.

2007-02-01

Molten salt electrolysis using CaCl2 is employed to produce pure titanium and its alloys directly from TiO2 and a mixture of elemental oxides, respectively, as an alternate to the Kroll process. This is because CaO, which is a reduction by-product, is highly soluble in CaCl2. Good-quality titanium containing only a small amount of residual oxygen has been successfully produced and scaled to industrial levels. Thermochemical and electrochemical bases are reviewed to optimize the process conditions. Several processes using molten salt are being examined for future progress in titanium processing.

Mechanosensitive cation channels in human leukaemia cells: calcium permeation and blocking effect

PubMed Central

Staruschenko, Alexandr V; Vedernikova, Elena A

2002-01-01

Cell-attached and inside-out patch-clamp methods were employed to identify and characterize mechanosensitive (MS) ionic channels in the plasma membrane of human myeloid leukaemia K562 cells. A reversible activation of gadolinium-blockable mechanogated currents in response to negative pressure application was found in 58 % of stable patches (n = 317). I-V relationships measured with a sodium-containing pipette solution showed slight inward rectification. Data analysis revealed the presence of two different populations of channels that were distinguishable by their conductance properties (17.2 ± 0.3 pS and 24.5 ± 0.5 pS), but were indistinguishable with regard to their selective and pharmacological properties. Ion-substitution experiments indicated that MS channels in leukaemia cells were permeable to cations but not to anions and do not discriminate between Na+ and K+. The channels were fully impermeable to large organic cations such as Tris+ and N-methyl-d-glucamine ions (NMDG+). Ca2+ permeation and blockade of MS channels were examined using pipettes containing different concentrations of Ca2+. In the presence of 2 mm CaCl2, when other cations were impermeant, both outward and inward single-channel currents were observed; the I-V relationship showed a unitary conductance of 7.7 ± 1.0 pS. The relative permeability value, PCa/PK, was equal to 0.75, as estimated at physiological Ca2+ concentrations. Partial or full inhibition of inward Ca2+ currents through MS channels was observed at higher concentrations of external Ca2+ (10 or 20 mm). No MS channels were activated when using a pipette containing 90 mm CaCl2. Monovalent mechanogated currents were not significantly affected by extracellular Ca2+ at concentrations within the physiological range (0-2 mm), and at some higher Ca2+ concentrations. PMID:12015421

Detection of Legume Protease Inhibitors by the Gel-X-ray Film Contact Print Technique

ERIC Educational Resources Information Center

Mulimani, Veerappa H.; Sudheendra, Kulkarni; Giri, Ashok P.

2002-01-01

Redgram (Cajanus cajan L.) extracts have been analyzed for the protease inhibitors using a new, sensitive, simple, and rapid method for detection of electrophoretically separated protease inhibitors. The detection involves equilibrating the gel successively in the protease assay buffer and protease solution, rinsing the gel in assay buffer, and…

Mechanisms of Aerobic Performance Impairment With Heat Stress and Dehydration

DTIC Science & Technology

2010-08-01

Jones (65) demonstrated that a menthol mouth rinse reduced RPE (com- pared with placebo) by 15% and improved TTE by 9% during exercise-heat stress...potentials. Appl Physiol Nutr Metab 35: 456–463, 2010. 65. Mundel T, Jones DA. The effects of swilling an l()- menthol solution during exercise in the

Electrochemical reduction behavior of simplified simulants of vitrified radioactive waste in molten CaCl2

NASA Astrophysics Data System (ADS)

Katasho, Yumi; Yasuda, Kouji; Nohira, Toshiyuki

2018-05-01

The electrochemical reduction of two types of simplified simulants of vitrified radioactive waste, simulant 1 (glass component only: SiO2, B2O3, Na2O, Al2O3, CaO, Li2O, and ZnO) and simulant 2 (also containing long-lived fission product oxides, ZrO2, Cs2O, PdO, and SeO2), was investigated in molten CaCl2 at 1103 K. The behavior of each element was predicted from the potential-pO2- diagram constructed from thermodynamic data. After the immersion of simulant 1 into molten CaCl2 without electrolysis, the dissolution of Na, Li, and Cs was confirmed by inductively coupled plasma atomic emission spectrometry and mass spectrometry analysis of the samples. The scanning electron microscopy/energy dispersive X-ray and X-ray diffraction analyses of simulants 1 and 2 electrolyzed at 0.9 V vs. Ca2+/Ca confirmed that most of SiO2 had been reduced to Si. After the electrolysis of simulants 1 and 2, Al, Zr, and Pd remained in the solid phase. In addition, SeO2 was found to remain partially in the solid phase and partially evaporate, although a small quantity dissolved into the molten salt.

Laboratory evaluation of disposable and reusable disinfectant cloths for cleaning food contact surfaces.

PubMed Central

Tebbutt, G. M.

1988-01-01

A comparison of five methods of cleaning Formica surfaces contaminated with bacteria dried in milk has been carried out. A standardized procedure was developed, and impression plates were found to be at least as sensitive as a swab-rinse method for detecting bacteria on the surfaces. The most satisfactory results were obtained with one type of disposable alcohol-impregnated wipe and with a detergent/hypochlorite solution applied with paper. A reusable cloth impregnated with disinfectant initially performed well against all test organisms, but was less reliable against Staphylococcus aureus and Streptococcus faecalis, after the cloth had been used and rinsed several times. The importance of introducing methods to reduce the high risk of cross-contamination presently associated with the use of wiping cloths in catering premises is stressed. PMID:3141202

METHOD OF ELECTROPLATING ON URANIUM

DOEpatents

Rebol, E.W.; Wehrmann, R.F.

1959-04-28

This patent relates to a preparation of metallic uranium surfaces for receiving coatings, particularly in order to secure adherent electroplated coatings upon uranium metal. In accordance with the invention the uranium surface is pretreated by degreasing in trichloroethylene, followed by immersion in 25 to 50% nitric acid for several minutes, and then rinsed with running water, prior to pickling in trichloroacetic acid. The last treatment is best accomplished by making the uranium the anode in an aqueous solution of 50 per cent by weight trichloroacetic acid until work-distorted crystals or oxide present on the metal surface have been removed and the basic crystalline structure of the base metal has been exposed. Following these initial steps the metallic uranium is rinsed in dilute nitric acid and then electroplated with nickel. Adnerent firmly-bonded coatings of nickel are obtained.

Operationally Defined Apoplastic and Symplastic Aluminum Fractions in Root Tips of Aluminum-Intoxicated Wheat

PubMed Central

Tice, Kathy R.; Parker, David R.; DeMason, Darleen A.

1992-01-01

Knowledge of the mechanistic basis of differential aluminum (Al) tolerance depends, in part, on an improved ability to quantify Al located in the apoplastic and symplastic compartments of the root apex. Using root tips excised from seedlings of an Al-tolerant wheat cultivar (Triticum aestivum L. cv Yecora Rojo) grown in Al solutions for 2 d, we established an operationally defined apoplastic Al fraction determined with six sequential 30-min washes using 5 mm CaCl2 (pH 4.3). Soluble symplastic Al was eluted by freezing root tips to rupture cell membranes and performing four additional 30-min CaCl2 washes, and a residual fraction was determined via digestion of root tips with HNO3. The three fractions were then determined in Yecora Rojo and a sensitive wheat cultivar (Tyler) grown at 18, 55, or 140 μm total solution Al (AlT). When grown at equal AlT, Tyler contained more Al than Yecora Rojo in all fractions, but both total Al and fractional distribution were similar in the two cultivars grown at AlT levels effecting a 50% reduction in root growth. Residual Al was consistently 50 to 70% of the total, and its location was elucidated by staining root tips with the fluorophore morin and examining them using fluorescence and confocal laser scanning microscopy. Wall-associated Al was only observed in tips prior to any washing, and the residual fraction was manifested as distinct staining of the cytoplasm and nucleus but not of the apoplastic space. Accordingly, the residual fraction was allocated to the symplastic compartment for both cultivars, and recalculated apoplastic Al was consistently approximately 30 to 40% of the total. Distributions of Al in the two cultivars did not support a symplastic detoxification hypothesis, but the role of cytoplasmic exclusion remains unsettled. Images Figure 4 Figure 5 PMID:16652962

Assessing the Efficacy of First-Aid Measures in Physalia sp. Envenomation, Using Solution- and Blood Agarose-Based Models

PubMed Central

Wilcox, Christie L.; Headlam, Jasmine L.; Doyle, Thomas K.; Yanagihara, Angel A.

2017-01-01

Stings from the hydrozoan species in the genus Physalia cause intense, immediate skin pain and elicit serious systemic effects. There has been much scientific debate about the most appropriate first aid for these stings, particularly with regard to whether vinegar use is appropriate (most current recommendations recommend against vinegar). We found that only a small percentage (≤1.0%) of tentacle cnidae discharge during a sting event using an ex vivo tissue model which elicits spontaneous stinging from live cnidarian tentacles. We then tested a variety of rinse solutions on both Atlantic and Pacific Physalia species to determine if they elicit cnidae discharge, further investigating any that did not cause immediate significant discharge to determine if they are able to inhibit cnidae discharge in response to chemical and physical stimuli. We found commercially available vinegars, as well as the recently developed Sting No More® Spray, were the most effective rinse solutions, as they irreversibly inhibited cnidae discharge. However, even slight dilution of vinegar reduced its protective effects. Alcohols and folk remedies, such as urine, baking soda and shaving cream, caused varying amounts of immediate cnidae discharge and failed to inhibit further discharge, and thus likely worsen stings. PMID:28445412

Comparison of the Efficacy of Three Different Mouthrinse Solutions in Decreasing the Level of Streptococcus Mutans in Saliva

PubMed Central

Kocak, Mustafa Murat; Ozcan, Suat; Kocak, Sibel; Topuz, Ozgur; Erten, Hulya

2009-01-01

Objectives The aim of this study was to evaluate the effectiveness of three different antiseptic mouthrinse solutions on the saliva samples obtained from the individuals, who had high caries activity rate. Methods The efficacy of three antiseptic mouthrinses were evaluated in a study with healthy volunteers. The three antiseptic solutions used in this study were 0.1% octenidine dihydrochloride (Octenisept, Schülke&Mayr, UK), 0.12% chlorhexidine digluconate (Kloroben, Drogsan, Turkey) and an antimicrobial enzymatic rinse (Biotene, Laclede, Inc, USA). A total of 27 adult volunteer subjects were participated in the study. The subjects were stratified into three balanced group. Then the mouth rinses were used by each group according to the manufacturer’s directions. The subjects were restricted for 60 minutes for food intake after using the prescribed mouthrinse. The saliva samples were collected from the volunteers at 1, 10 and 60 minutes after their usage in tubes. The tubes were kept in +4°C in a fridge till the evaluation. 10−3 and 10−5 dilutions were prepared for each solution and S. mutans were evaluated according to total number of colony forming unit (CFU) per ml. The dilutions were spreaded on the surface of Brucella agar plates for anaerobic incubation for 48 hours. The dilutions were 100, 10−3 and 10−5 of the solutions Kloroben, Biotene, Octenisept, and the time factor were 0, 1, 10 and 60 minutes. The statistical analyses were performed by Duncan and Bonferroni tests. Results Octenisept was found to be more effective over S. mutans than the other mouthrinse solutions (P<.05). Conclusions All mouthrinse solutions except Biotene were effective on oral microorganisms. PMID:19262732

Cleaning by Surfactant Gradients: Particulate Removal from Porous Materials and the Significance of Rinsing in Laundry Detergency

NASA Astrophysics Data System (ADS)

Shin, Sangwoo; Warren, Patrick B.; Stone, Howard A.

2018-03-01

Removing particles from fibrous materials involves loosening via surfactants followed by particle transfer in a flow. While flow advection is commonly believed to be the major driver for pore-scale transport, small pores within the fabric do not allow any significant fluid flow inside them, thus significantly reducing the role of advection. However, rinsing the fabric with fresh water naturally establishes a surfactant gradient within the pore space, providing a suitable environment for particles to undergo diffusiophoresis. We demonstrate that this mechanism can remove particles from deep within fabric pores at an accelerated rate. The nonlinear aspect of diffusiophoresis significantly prolongs the lifetime of the phoretic motion beyond the naive solute diffusion time scale during rinsing, allowing long-lasting, continuous removal of particles. Moreover, owing to the fine balance between chemiphoresis and electrophoresis for particles in anionic surfactant concentration gradients, we show that the particle removal is sensitive to the counterion mobility, suggesting a simple route to control the effect. We thus claim to have resolved the "stagnant core problem"—a long-standing mystery in laundry detergency—and have identified a physicochemical approach to particle transport in fibrous media with broad applicability.

Differential role of ethylene and hydrogen peroxide in dark-induced stomatal closure.

PubMed

Kar, R K; Parvin, N; Laha, D

2013-12-15

Regulation of stomatal aperture is crucial in terrestrial plants for controlling water loss and gaseous exchange with environment. While much is known of signaling for stomatal opening induced by blue light and the role of hormones, little is known about the regulation of stomatal closing in darkness. The present study was aimed to verify their role in stomatal regulation in darkness. Epidermal peelings from the leaves of Commelina benghalensis were incubated in a defined medium in darkness for 1 h followed by a 1 h incubation in different test solutions [H2O2, propyl gallate, ethrel (ethylene), AgNO3, sodium orthovanadate, tetraethyl ammonium chloride, CaCl2, LaCl3, separately and in combination] before stomatal apertures were measured under the microscope. In the dark stomata remained closed under treatments with ethylene and propyl gallate but opened widely in the presence of H2O2 and AgNO3. The opening effect was largely unaffected by supplementing the treatment with Na-vanadate (PM H+ ATPase inhibitor) and tetraethyl ammonium chloride (K(+)-channel inhibitor) except that opening was significantly inhibited by the latter in presence of H2O2. On the other hand, H2O2 could not override the closing effect of ethylene at any concentrations while a marginal opening of stomata was found when Ag NO3 treatment was given together with propyl gallate. CaCl2 treatment opened stomata in the darkness while LaCl3 maintained stomata closed. A combination of LaCl3 and propyl gallate strongly promoted stomatal opening. A probable action of ethylene in closing stomata of Commelina benghalensis in dark has been proposed.

An efficient method to eliminate the protease activity contaminating commercial bovine pancreatic DNase I.

PubMed

Le, Tien; Lee, Hak Jin; Jin, Hyung Jong

2015-08-15

A method was developed to eliminate the proteases contaminating commercial DNase I, which can cause degradation of target protein during the purification process. Bio Basic DNase stock solution (in Tris-HCl buffer [pH 8.0] containing 5mM CaCl2) was first incubated at 50 °C to generate autolysis of proteases and zymogens, leading to a significant reduction in protease activity while preserving DNase activity. The residual protease activity was completely inhibited by further incubation with 2mM PMSF (phenylmethylsulfonyl fluoride) or 2× S8830 inhibitor cocktail. This approach could be readily applicable to eliminate the protease activity in any DNase products or during the preparation of commercial DNase. Copyright © 2015 Elsevier Inc. All rights reserved.

Wipe-rinse technique for quantitating microbial contamination on large surfaces.

PubMed Central

Kirschner, L E; Puleo, J R

1979-01-01

The evaluation of an improved wipe-rinse technique for the bioassay of large areas was undertaken due to inherent inadequacies in the cotton swab-rinse technique to which assay of spacecraft is currently restricted. Four types of contamination control cloths were initially tested. A polyester-bonded cloth (PBC) was selected for further evaluation because of its superior efficiency and handling characteristics. Results from comparative tests with PBC and cotton swabs on simulated spacecraft surfaces indicated a significantly higher recovery efficiency for the PBC than for the cotton (90.4 versus 75.2%). Of the sampling areas sites studied, PBC was found to be most effective on surface areas not exceeding 0.74 m2 (8.0 feet 2). PMID:394682

Effects of chlorhexidine preprocedural rinse on bacteremia in periodontal patients: a randomized clinical trial

PubMed Central

Balejo, Rodrigo Dalla Pria; Cortelli, José Roberto; Costa, Fernando Oliveira; Cyrino, Renata Magalhães; Aquino, Davi Romeiro; Cogo-Müller, Karina; Miranda, Taís Browne; Moura, Sara Porto; Cortelli, Sheila Cavalca

2017-01-01

Abstract Objective: Single dose of systemic antibiotics and short-term use of mouthwashes reduce bacteremia. However, the effects of a single dose of preprocedural rinse are still controversial. This study evaluated, in periodontally diseased patients, the effects of a pre-procedural mouth rinse on induced bacteremia. Material and Methods: Systemically healthy individuals with gingivitis (n=27) or periodontitis (n = 27) were randomly allocated through a sealed envelope system to: 0.12% chlorhexidine pre-procedural rinse (13 gingivitis and 13 periodontitis patients) or no rinse before dental scaling (14 gingivitis and 15 periodontitis patients). Periodontal probing depth, clinical attachment level, plaque, and gingival indices were measured and subgingival samples were collected. Blood samples were collected before dental scaling, 2 and 6 minutes after scaling. Total bacterial load and levels of P. gingivalis were determined in oral and blood samples by real-time polymerase chain reaction, while aerobic and anaerobic counts were determined by culture in blood samples. The primary outcome was the antimicrobial effect of the pre-procedural rinse. Data was compared by Mann-Whitney and Signal tests (p<0.05). Results: In all sampling times, polymerase chain reaction revealed higher blood bacterial levels than culture (p<0.0001), while gingivitis patients presented lower bacterial levels in blood than periodontitis patients (p<0.0001). Individuals who experienced bacteremia showed worse mean clinical attachment level (3.4 mm vs. 1.1 mm) and more subgingival bacteria (p<0.005). The pre-procedural rinse did not reduce induced bacteremia. Conclusions: Bacteremia was influenced by periodontal parameters. In periodontally diseased patients, pre-procedural rinsing showed a discrete effect on bacteremia control. PMID:29211279

The use of an oxidising mouthwash to reduce staining associated with chlorhexidine. Studies in vitro and in vivo.

PubMed

Addy, M; al-Arrayed, F; Moran, J

1991-04-01

Discolouration of the teeth, tongue and dental restorative materials associated with the use of cationic antiseptics is still the limiting factor in long-term usage of antiplaque agents such as chlorhexidine. Oxidising agents have been used successfully to remove dental stain in animals, but products and regimens have not been evaluated in humans. These pilot studies in vitro and in vivo assessed a long-established oxidising mouthwash, based on peroxyborate, for stain removal from teeth and acrylic. The laboratory studies measured chlorhexidine tea stain removal from tooth and acrylic specimens. The oxidising agent markedly reduced staining on specimens. In a short-term clinical experiment, dental staining was forced over a 2 1/2-day period by reciprocal chlorhexidine and tea rinsing. 5 rinses with the oxidising mouthwash during the next 1 1/2 days dramatically reduced staining compared with water after rinses. Additionally, a single rinse with peroxyborate following the 5 water after rinses, again considerably reduced the residual staining. Effects on tongue staining were less impressive. Both experimental models produced findings consistent with those from the animal model. The results suggest proprietary oxidising mouthwashes could have a place in the control of dental stain associated with the use of chlorhexidine. Further studies to evaluate such products in a more conventional chlorhexidine regimen are indicated.

The effect of heparin rinse on the biocompatibility of continuous veno-venous hemodiafiltration.

PubMed

Opatrný, K; Polanská, K; Krouzecký, A; Vít, L; Novák, I; Kasal, E

2002-06-01

The aims of our cross-over randomized study were (1) to assess hemostasis in patients with acute renal failure (ARF) and (2) to determine whether or not the generally recommended heparin rinse of the extracorporeal circuit (ECC) prior to the procedure affects thrombogenicity, complement activation, and leukocyte count in blood during continuous venovenous hemodiafiltration (CVVHDF). Eleven critically ill ARF patients were treated, in random order, using CVVHDF in postdilution setup following ECC rinse with saline (A) with heparin at a concentration of 2,000 IU/L (10 procedures), (B) with heparin at a concentration of 10,000 IU/L (7 procedures), and (C) without heparin (9 procedures). Except for the rinse, anticoagulation therapy did not differ in individual patients during the procedures. Blood was withdrawn before, and at minutes 15, 60, and 360 invariably at diafilter inlet and outlet. Compared with healthy individuals, patients showed lower blood thrombocyte counts (153 vs 233*10(9)/L, p<0.01, arithmetic means, Student's t test), longer aPTT (44 vs 36 s, p<0.05), higher plasma levels of heparin (0.1 vs 0.0 U/mL, p<0.05), D-dimer (1129 vs 36 ng/mL, p<0.001) and beta-thromboglobulin (BTG) (159 vs 37 U/mL, p<0.001) prior to CVVHDF. The comparison of procedures with different rinsing technique did not reveal any significant difference in their effects on blood thrombocyte and leukocyte counts, aPTT, plasma levels of heparin, BTG, thrombin-antithrombin III complexes, D-dimer, or the C5a complement component. (1) Patients indicated for CVVHDF show impaired hemostasis involving thrombocytes, coagulation, and fibrinolysis, (2) no beneficial effect of heparin rinse on CVVHDF ECC thrombogenicity, complement activation or blood leukocyte counts was demonstrated.

An investigation of matched index of refraction technique and its application in optical measurements of fluid flow

NASA Astrophysics Data System (ADS)

Amini, Noushin; Hassan, Yassin A.

2012-12-01

Optical distortions caused by non-uniformities of the refractive index within the measurement volume is a major impediment for all laser diagnostic imaging techniques applied in experimental fluid dynamic studies. Matching the refractive indices of the working fluid and the test section walls and interfaces provides an effective solution to this problem. The experimental set-ups designed to be used along with laser imaging techniques are typically constructed of transparent solid materials. In this investigation, different types of aqueous salt solutions and various organic fluids are studied for refractive index matching with acrylic and fused quartz, which are commonly used in construction of the test sections. One aqueous CaCl2·2H2O solution (63 % by weight) and two organic fluids, Dibutyl Phthalate and P-Cymene, are suggested for refractive index matching with fused quartz and acrylic, respectively. Moreover, the temperature dependence of the refractive indices of these fluids is investigated, and the Thermooptic Constant is calculated for each fluid. Finally, the fluid viscosity for different shear rates is measured as a function of temperature and is applied to characterize the physical behavior of the proposed fluids.

Commercial Scale Cucumber Fermentations Brined with Calcium Chloride Instead of Sodium Chloride.

PubMed

Pérez-Díaz, I M; McFeeters, R F; Moeller, L; Johanningsmeier, S D; Hayes, J; Fornea, D S; Rosenberg, L; Gilbert, C; Custis, N; Beene, K; Bass, D

2015-12-01

Development of low salt cucumber fermentation processes present opportunities to reduce the amount of sodium chloride (NaCl) that reaches fresh water streams from industrial activities. The objective of this research was to translate cucumber fermentation brined with calcium chloride (CaCl2 ) instead of NaCl to commercial scale production. Although CaCl2 brined cucumber fermentations were stable in laboratory experiments, commercial scale trials using 6440 L open-top tanks rapidly underwent secondary cucumber fermentation. It was understood that a limited air purging routine, use of a starter culture and addition of preservatives to the cover brine aids in achieving the desired complete cucumber fermentation. The modified process was used for subsequent commercial trials using 12490 and 28400 L open-top tanks packed with variable size cucumbers and from multiple lots, and cover brines containing CaCl2 and potassium sorbate to equilibrated concentrations of 100 and 6 mM, respectively. Lactobacillus plantarum LA0045 was inoculated to 10(6) CFU/mL, and air purging was applied for two 2-3 h periods per day for the first 10 d of fermentation and one 2-3 h period per day between days 11 and 14. All fermentations were completed, as evidenced by the full conversion of sugars to lactic acid, decrease in pH to 3.0, and presented microbiological stability for a minimum of 21 d. This CaCl2 process may be used to produce fermented cucumbers intended to be stored short term in a manner that reduces pollution and waste removal costs. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Chemical vs. Physical Acceleration of Cement Hydration

PubMed Central

Bentz, Dale P.; Zunino, Franco; Lootens, Didier

2016-01-01

Cold weather concreting often requires the use of chemical accelerators to speed up the hydration reactions of the cement, so that setting and early-age strength development will occur in a timely manner. While calcium chloride (dihydrate – CaCl2·2H2O) is the most commonly used chemical accelerator, recent research using fine limestone powders has indicated their high proficiency for physically accelerating early-age hydration and reducing setting times. This paper presents a comparative study of the efficiency of these two approaches in accelerating hydration (as assessed via isothermal calorimetry), reducing setting times (Vicat needle), and increasing early-age mortar cube strength (1 d and 7 d). Both the CaCl2 and the fine limestone powder are used to replace a portion of the finest sand in the mortar mixtures, while keeping both the water-to-cement ratio and volume fractions of water and cement constant. Studies are conducted at 73.4 °F (23°C) and 50 °F (10 °C), so that activation energies can be estimated for the hydration and setting processes. Because the mechanisms of acceleration of the CaCl2 and limestone powder are different, a hybrid mixture with 1 % CaCl2 and 20 % limestone powder (by mass of cement) is also investigated. Both technologies are found to be viable options for reducing setting times and increasing early-age strengths, and it is hoped that concrete producers and contractors will consider the addition of fine limestone powder to their toolbox of techniques for assuring performance in cold weather and other concreting conditions where acceleration may be needed. PMID:28077884

Comparative efficacy of two daily use mouthrinses: randomized clinical trial using an experimental gingivitis model.

PubMed

Charles, Christine Ann; McGuire, James Anthony; Sharma, Naresh Chandra; Qaqish, James

2011-01-01

Two antimicrobial agents, a fixed combination of essential oils (EOs) and 0.07% cetylpyridinium chloride (CPC) are found in commercially available mouthrinses, Listerine® Antiseptic and Crest® Pro HealthTM, respectively. Both mouthrinses have been shown to control dental plaque and gingivitis in short and longer term studies. The aim of this study was to determine the comparative effectiveness of these two mouthrinses using a 2-week experimental gingivitis model. Qualified subjects were randomly assigned to one of three mouthrinse groups: a fixed combination of EOs, 0.07% CPC, or negative control (C) rinse. Following baseline clinical assessments and a dental prophylaxis, subjects began a two-week period in which they rinsed twice daily with their assigned rinse and abstained from any mechanical oral hygiene procedures or other oral care products. Subjects were reassessed at the end of the two-week period. One hundred and forty-seven subjects were randomized and 142 completed this study. After two weeks use, the EOs rinse was superior (p < 0.011) to the CPC rinse in inhibiting the development of gingivitis, plaque, and bleeding, with 9.4% and 6.6% reductions compared to CPC for gingivitis and plaque, respectively. Both rinses were superior to the negative control rinse (p < 0.001). This study demonstrates that the essential oil-containing mouthrinse has superior antiplaque/antigingivitis effectiveness compared to the 0.07% CPC-containing mouthrinse without mechanical oral hygiene influence.

40 CFR 471.35 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... Fluoride 13.9 6.15 (w) Molten salt rinse. Subpart C—PSNS Pollutant or pollutant property Maximum for any 1... with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 (x) Ammonia rinse. Subpart...

40 CFR 471.35 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... Fluoride 13.9 6.15 (w) Molten salt rinse. Subpart C—PSNS Pollutant or pollutant property Maximum for any 1... with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 (x) Ammonia rinse. Subpart...

40 CFR 471.35 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... Fluoride 13.9 6.15 (w) Molten salt rinse. Subpart C—PSNS Pollutant or pollutant property Maximum for any 1... with molten salt Chromium 0.312 0.127 Nickel 0.464 0.312 Fluoride 50.2 22.3 (x) Ammonia rinse. Subpart...

Vitamin K2 inhibits rat vascular smooth muscle cell calcification by restoring the Gas6/Axl/Akt anti-apoptotic pathway.

PubMed

Qiu, Cuiting; Zheng, Haijun; Tao, Huiren; Yu, Wenjun; Jiang, Xiaoyu; Li, Aiqin; Jin, Hui; Lv, Anlin; Li, Huan

2017-09-01

Vascular calcification is associated with cardiovascular disease as a complication of hypertension, hyperlipidemia, diabetes mellitus, and chronic kidney disease. Vitamin K2 (VK2) delays vascular calcification by an unclear mechanism. Moreover, apoptosis modulates vascular smooth muscle cell (VSMC) calcification. This paper aimed to study VK2-modified VSMC calcification and survival cell signaling mediated by growth arrest-specific gene 6 (Gas6) and its tyrosine kinase receptor Axl. Primary-cultured VSMCs were dose-dependently treated with VK2 in the presence of calcification medium for 8 days, or pre-treated for 1 h with/without the Axl inhibitor R428 (2 μmol/L) or the caspase inhibitor Z-VAD-fmk (20 μmol/L) followed by treatment with VK2 (10 μmol/L) or rmGas6 (200 nmol/L) in calcification medium for 8 days. Calcium deposition was determined by the o-cresolphthalein complexone assay and Alizarin Red S staining. Apoptosis was determined by TUNEL and flow cytometry using Annexin V-FITC and propidium iodide staining. Western blotting detected the expressions of Axl, Gas6, p-Akt, Akt, and Bcl2. VK2 significantly inhibited CaCl 2 - and β-sodium glycerophosphate (β-GP)-induced VSMC calcification and apoptosis, which was dependent on restored Gas6 expression and activated downstream signaling by Axl, p-Akt, and Bcl2. Z-VAD-fmk significantly inhibited CaCl 2 - and β-GP-induced VSMC calcification and apoptosis. Augmented recombinant mouse Gas6 protein (rmGas6) expression significantly reduced VSMC calcification and apoptosis. Furthermore, the Gas6/Axl interaction was inhibited by R428, which abolished the preventive effect of VK2 on CaCl 2 - and β-GP-induced apoptosis and calcification. These results suggest that Gas6 is critical in VK2-mediated functions that attenuate CaCl 2 - and β-GP-induced VSMC calcification by blocking apoptosis.

Osmotic swelling of polyacrylate hydrogels in physiological salt solutions.

PubMed

Horkay, F; Tasaki, I; Basser, P J

2000-01-01

The swelling behavior of fully neutralized sodium polyacrylate gels was investigated in aqueous solutions of alkali metal (LiCl, NaCl, KCl, CsCl) and alkaline earth metal salts (CaCl2, SrCl2, BaCl2). The total salt concentration and the ratio of monovalent to divalent cations were varied in the biologically significant range. It is found that the concentrations of both monovalent and divalent cations vary continuously and smoothly in the gel despite the abrupt change in the gel volume. The individual elastic, mixing, and ionic contributions to the free energy of the gel were separately determined as a function of the degree of network swelling to elucidate the thermodynamics of swelling. Shear modulus measurements performed at different Ca2+ concentrations suggest that Ca2+ does not form stable cross-links between the polymer chains. At low and moderate swelling ratios the concentration dependence of the shear modulus follows a power law behavior, G variation of phi n, with n = 0.34 +/- 0.03. At high swelling degrees, however, the shear modulus increases with increasing swelling. The value of the Flory-Huggins interaction parameter, chi, determined from osmotic swelling pressure and shear modulus measurements, strongly depends on the ionic composition of the equilibrium solution and increases with increasing Ca2+ concentration.

Metabolomic assessment reveals an elevated level of glucosinolate content in CaCl₂ treated broccoli microgreens.

PubMed

Sun, Jianghao; Kou, Liping; Geng, Ping; Huang, Huilian; Yang, Tianbao; Luo, Yaguang; Chen, Pei

2015-02-18

Preharvest calcium application has been shown to increase broccoli microgreen yield and extend shelf life. In this study, we investigated the effect of calcium application on its metabolome using ultra-high-performance liquid chromatography with mass spectrometry. The data collected were analyzed using principal component analysis and orthogonal projection to latent structural discriminate analysis. Chemical composition comparison shows that glucosinolates, a very important group of phytochemicals, are the major compounds enhanced by preharvest treatment with 10 mM calcium chloride (CaCl2). Aliphatic glucosinolates (glucoerucin, glucoiberin, glucoiberverin, glucoraphanin, pentyl glucosinolate, and hexyl glucosinolate) and indolic glucosinolates (glucobrassicin, neoglucobrassicin, and 4-hydroxyglucobrassicin) were increased significantly in the CaCl2 treated microgreens using metabolomic approaches. Targeted glucosinolate analysis using the ISO 9167-1 method was further employed to confirm the findings. Results indicate that glucosinolates can be considered as a class of compounds that are responsible for the difference between two groups and a higher glucosinolate level was found in CaCl2 treated groups at each time point after harvest in comparison with the control group.

Accelerating the sludge disintegration potential of a novel bacterial strain Planococcus jake 01 by CaCl2 induced deflocculation.

PubMed

Kavitha, S; Saranya, T; Kaliappan, S; Adish Kumar, S; Yeom, Ick Tae; Rajesh Banu, J

2015-01-01

The present study investigates the impacts of phase separated disintegration through CaCl2 (calcium chloride) mediated biosurfactant producing bacterial pretreatment. In the initial phase of the study, the flocs were disintegrated (deflocculation) with 0.06g/gSS of CaCl2. In the subsequent phase, the sludge biomass was disintegrated (cell disintegration) through potent biosurfactant producing new novel bacteria, Planococcus jake 01. The pretreatment showed that suspended solids reduction and chemical oxygen demand solubilization for deflocculated - bacterially pretreated sludge was found to be 17.14% and 14.14% which were comparatively higher than flocculated sludge (treated with bacteria alone). The biogas yield potential of deflocculated - bacterially pretreated, flocculated, and control sludges were observed to be 0.322(L/gVS), 0.225(L/gVS) and 0.145(L/gVS) respectively. To our knowledge, this is the first study to present the thorough knowledge of biogas production potential through a novel phase separated biosurfactant bacterial pretreatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

In-vitro evidence for efficacy of antimicrobial mouthrinses

PubMed Central

Pan, Pauline C.; Harper, Scott; Ricci-Nittel, Danette; Lux, Renate; Shi, Wenyuan

2010-01-01

SUMMARY Objectives The objective of this study was to compare the antimicrobial activity of commercially available antiseptic mouthrinses against saliva-derived plaque biofilms in static and flow-through biofilm systems in vitro. Methods Nine mouthrinses were tested in a recirculating flow-through biofilm model (RFTB) with viability assessment by ATP bioluminescence. In addition, five mouthrinses were evaluated in a batch chamber slide biofilm (BCSB) model, using live- dead staining and confocal laser scanning microscopy. Results In the RFTB model, essential oil (EO) and chlorhexidine (CHX)-containing rinses showed equivalent antimicrobial activity and were more effective than a range of cetyl pyridinium chloride (CPC1) formulations. In the BCSB model, twice-daily mouthrinse exposure demonstrated that the EO rinse was significantly more effective than rinses containing amine and stannous fluorides, a combination of CPC/CHX and CPC2. EO showed biofilm kill comparable to the CHX rinse. Conclusions The present studies have shown that mouthrinses vary significantly in their capability to kill plaque biofilm bacteria in BCSB and RFTB models. The EO mouthrinse demonstrated superior antiplaque biofilm activity to AFSF, CPC/CHX, and CPC rinses and comparable activity to CHX. The methods tested may be of value for the in-vitro screening of antiseptic rinses with different modes of antimicrobial action. PMID:20621239

Comparison of Antimicrobial Efficacy of Green Tea, Garlic with Lime, and Sodium Fluoride Mouth Rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans in Children: A Randomized Double-blind Controlled Clinical Trial

PubMed Central

Thomas, Ann; Habib, Rishika

2017-01-01

Introduction With greater awareness worldwide, the use of herbs and herbal products has increased to a large extent. Objective To evaluate and compare the antimicrobial efficacy of green tea, garlic with lime, and 0.05% sodium fluoride (NaF) mouth rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans. Materials and methods A total of 45 children aged 4 to 6 years with severe early childhood caries (S-ECC; based on decayed extracted filled [defs] score) were selected. Children were divided randomly into three equal groups and were asked to rinse with the prescribed mouth rinse once daily for 2 weeks after breakfast under supervision. A base-line and postrinsing nonstimulated whole salivary sample (2 mL) was collected and tested for the number of colony-forming units (CFUs). The data were statistically analyzed using Statistical Package for the Social Sciences (SPSS) version 16.0 software with one-way analysis of variance (ANOVA) and Tukey’s post hoc test. Results A statistically significant fall in colony count was found with the three mouth rinses in S. mutans (p < 0.001, p < 0.001) and Lactobacilli spp. (p < 0.001, p < 0.001), but not against C. albicans (p = 0.264, p = 0.264). On comparison, no statistically significant difference was found against S. mutans (p = 1, p = 0.554, p = 0.572), lactobacilli spp. (p = 0.884, p = 0.999, p = 0.819), and C. albicans (p = 0.999, p = 0.958, p = 0.983). Conclusion The findings of this study indicate that green tea and garlic with lime mouth rinse can be an economical alternative to NaF mouth rinse both for prevention and therapeutics. How to cite this article Thomas A, Thakur S, Habib R. Comparison of Antimicrobial Efficacy of Green Tea, Garlic with Lime, and Sodium Fluoride Mouth Rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans in Children: A Randomized Double-blind Controlled Clinical Trial. Int J Clin Pediatr Dent 2017;10(3):234-239. PMID:29104381

Comparison of Antimicrobial Efficacy of Green Tea, Garlic with Lime, and Sodium Fluoride Mouth Rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans in Children: A Randomized Double-blind Controlled Clinical Trial.

PubMed

Thomas, Ann; Thakur, Sneha; Habib, Rishika

2017-01-01

With greater awareness worldwide, the use of herbs and herbal products has increased to a large extent. To evaluate and compare the antimicrobial efficacy of green tea, garlic with lime, and 0.05% sodium fluoride (NaF) mouth rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans. A total of 45 children aged 4 to 6 years with severe early childhood caries (S-ECC; based on decayed extracted filled [defs] score) were selected. Children were divided randomly into three equal groups and were asked to rinse with the prescribed mouth rinse once daily for 2 weeks after breakfast under supervision. A base-line and postrinsing nonstimulated whole salivary sample (2 mL) was collected and tested for the number of colony-forming units (CFUs). The data were statistically analyzed using Statistical Package for the Social Sciences (SPSS) version 16.0 software with one-way analysis of variance (ANOVA) and Tukey's post hoc test. A statistically significant fall in colony count was found with the three mouth rinses in S. mutans (p < 0.001, p < 0.001) and Lactobacilli spp. (p < 0.001, p < 0.001), but not against C. albicans (p = 0.264, p = 0.264). On comparison, no statistically significant difference was found against S. mutans (p = 1, p = 0.554, p = 0.572), lactobacilli spp. (p = 0.884, p = 0.999, p = 0.819), and C. albicans (p = 0.999, p = 0.958, p = 0.983). The findings of this study indicate that green tea and garlic with lime mouth rinse can be an economical alternative to NaF mouth rinse both for prevention and therapeutics. Thomas A, Thakur S, Habib R. Comparison of Antimicrobial Efficacy of Green Tea, Garlic with Lime, and Sodium Fluoride Mouth Rinses against Streptococcus mutans, Lactobacilli species, and Candida albicans in Children: A Randomized Double-blind Controlled Clinical Trial. Int J Clin Pediatr Dent 2017;10(3):234-239.

The role of calcium and calmodulin in freezing-induced freezing resistance of Populus tomentosa cuttings.

PubMed

Lin, Shan-Zhi; Zhang, Zhi-Yi; Lin, Yuan-Zhen; Zhang, Qian; Guo, Huan

2004-02-01

To explore the role of calcium-calmodulin messenger system in the transduction of low temperature signal in woody plants, Populus tomentosa cuttings after being treated with CaCl(2) (10 mmol/L), Ca(2+) chelator EGTA (3 mmol/L), Ca(2+) channel inhibitor LaCl(3) (100 mmol/L) or CaM antagonist CPZ (50 mmol/L) were used for freezing acclimation at -3 degrees C. The changes in the calmodulin (CaM) and malonaldehyde (MDA) contents, the activities of superoxide dismutase (SOD), peroxidase (POD) and Ca(2+)-dependent adenosinetriphosphatase (Ca(2+)-ATPase) of mitochondrial membrane as well as freezing resistance (expressed as LT(50)) of cuttings were investigated to elucidate the physiological mechanisms by which trees adapt to freezing. The results showed that freezing acclimation increased the CaM content, the activities of SOD, POD and Ca(2+)-ATPase of mitochondrial membrane as well as freezing resistance of cuttings, and decreased the MDA content as compared with control cuttings. Treatment with CaCl(2) at the time of freezing acclimation enhanced the effect of freezing acclimation on the above-mentioned indexes, but this enhancement was abolished by Ca(2+)chelator EGTA, Ca(2+) channel inhibitor LaCl(3) or CaM antagonist CPZ, indicating that the calcium-calmodulin messenger system was involved in the course of freezing resistance development. The presence of CaCl(2) at the same time of freezing acclimation also reduced the degree of decline in CaM content, and in SOD, POD and Ca(2+)-ATPase activities caused by freezing stress at -14 degrees C, and enhanced the level of increase in CaM content, and in SOD, POD and Ca(2+)-ATPase activity in the recovery periods at 25 degrees C . The change in CaM content was found to be closely correlated to the levels of SOD, POD and Ca(2+)-ATPase, and to the degree of freezing resistance of cuttings during freezing acclimation either with or without CaCl(2) treatment. It was suggested that the increase of CaM content induced by CaCl(2) treatment promote the formation of Ca(2+)-CaM complexes, which effectively activates the activities of SOD, POD and mitochondrial Ca(2+)-ATPase and then further result in the adaptive changes associated with the development and enhancement of freezing resistance. Thus, It could be concluded that Ca(2+)-calmodulin may be involved in the regulation of the increase in SOD, POD and Ca(2+)-ATPase activities, and the induction of freezing resistance of cuttings.

Effects of ruthenium ions on the sensory terminal discharges of the frog muscle spindle.

PubMed

Ito, F; Fujitsuka, N; Komatsu, Y

1983-10-16

The presence of a mixed Na+-Ca2+ spike along the sensory terminal of the frog muscle spindle was verified. When the terminal was perfused with Ringer's solution containing 0.1-0.5 mM ruthenium red (RuR), the amplitude and duration of the spike were increased, occurring as a prolonged or a long-lasting depolarization of up to 20-30 s duration following individual afferent spikes evoked spontaneously or antidromically by electrical stimulation. In an isotonic TEA solution, the amplitude and duration of the afferent spikes were increased; however, no prolonged depolarization occurred. Adding 0.2 mM RuR to the TEA solution produced the prolonged and long-lasting depolarization. All responses disappeared in the presence of 3 microM TTX or Na+-free Ringer's solution. An impedance decrease along the terminal was observed during the prolonged or long-lasting depolarization. The prolonged depolarization was blocked by the addition of Ca2+-blockers; the afferent spikes remained. In preparations preincubated with 0.1 mM RuR, increasing CaCl2 in Ringer's solution from 0.2 mM, resulted in shortening of the duration of individual spikes with prolonged depolarization and in increase in the maximum rate of rise (MRR) of the spikes. Preincubation with higher concentrations of RuR produced higher sensitivities in the modifications of the duration and MRR to the change in [Ca2+]O. The responses were retained by adding RuR or RuCl3 to Ca2+-free Ringer's solution containing 0.1-5 mM EGTA, although all responses disappeared in Ca2+-free EGTA Ringer's solution. It is concluded that the RuR-induced prolonged response is produced by an influx of Na+.

Ionic Effects on Supercritical CO2-Brine Interfacial Tensions: Molecular Dynamics Simulations and a Universal Correlation with Ionic Strength, Temperature, and Pressure.

PubMed

Zhao, Lingling; Ji, Jiayuan; Tao, Lu; Lin, Shangchao

2016-09-13

For geological CO2 storage in deep saline aquifers, the interfacial tension (IFT) between supercritical CO2 and brine is critical for the storage security and design of the storage capacitance. However, currently, no predictive model exists to determine the IFT of supercritical CO2 against complex electrolyte solutions involving various mixed salt species at different concentrations and compositions. In this paper, we use molecular dynamics (MD) simulations to investigate the effect of salt ions on the incremental IFT at the supercritical CO2-brine interface with respect to that at the reference supercritical CO2-water interface. Supercritical CO2-NaCl solution, CO2-CaCl2 solution and CO2-(NaCl+CaCl2) mixed solution systems are simulated at 343 K and 20 MPa under different salinities and salt compositions. We find that the valence of the cations is the primary contributor to the variation in IFT, while the Lennard-Jones potentials for the cations pose a smaller impact on the IFT. Interestingly, the incremental IFT exhibits a general linear correlation with the ionic strength in the above three electrolyte systems, and the slopes are almost identical and independent of the solution types. Based on this finding, a universal predictive formula for IFTs of CO2-complex electrolyte solution systems is established, as a function of ionic strength, temperature, and pressure. The predicted IFTs using the established formula agree perfectly (with a high statistical confidence level of ∼96%) with a wide range of experimental data for CO2 interfacing with different electrolyte solutions, such as those involving MgCl2 and Na2SO4. This work provides an efficient and accurate route to directly predict IFTs in supercritical CO2-complex electrolyte solution systems for practical engineering applications, such as geological CO2 sequestration in deep saline aquifers and other interfacial systems involving complex electrolyte solutions.

Ferrate(VI) oxidation of zinc-cyanide complex.

PubMed

Yngard, Ria; Damrongsiri, Seelawut; Osathaphan, Khemarath; Sharma, Virender K

2007-10-01

Zinc-cyanide complexes are found in gold mining effluents and in metal finishing rinse water. The effect of Zn(II) on the oxidation of cyanide by ferrate(VI) (Fe(VI)O(4)(2-), Fe(VI)) was thus investigated by studying the kinetics of the reaction of Fe(VI) with cyanide present in a potassium salt of a zinc cyanide complex (K(2)Zn(CN)(4)) and in a mixture of Zn(II) and cyanide solutions as a function of pH (9.0-11.0). The rate-law for the oxidation of Zn(CN)(4)(2-) by Fe(VI) was found to be -d[Fe(VI)]/dt=k[Fe(VI)][Zn(CN)(4)(2-)](0.5). The rate constant, k, decreased with an increase in pH. The effect of temperature (15-45 degrees C) on the oxidation was studied at pH 9.0, which gave an activation energy of 45.7+/-1.5kJmol(-1). The cyanide oxidation rate decreased in the presence of the Zn(II) ions. However, Zn(II) ions had no effect on the cyanide removal efficiency by Fe(VI) and the stoichiometry of Fe(VI) to cyanide was approximately 1:1; similar to the stoichiometry in absence of Zn(II) ions. The destruction of cyanide by Fe(VI) resulted in cyanate. The experiments on removal of cyanide from rinse water using Fe(VI) demonstrated complete conversion of cyanide to cyanate.

Mouth rinsing with a carbohydrate solution does not influence cycle time trial performance in the heat.

PubMed

Watson, Phillip; Nichols, David; Cordery, Philip

2014-09-01

Ten endurance-trained males were recruited to examine the possible role of carbohydrate (CHO) receptors in the mouth influencing exercise performance in the heat. Volunteers completed an incremental test to exhaustion to determine peak oxygen uptake, a familiarisation trial, followed by 2 experimental trials. Trials consisted of a 1-h time trial undertaken in a climatic chamber maintained at 30 °C, 60% relative humidity. Immediately before, and at regular intervals throughout exercise, subjects ingested a bolus of water and then were provided with either a placebo (PLA) or a 6.4% glucose (CHO) solution to rinse in the mouth for 10 s before being expectorated. There was no difference in total work done between the PLA and CHO trials (758.8 ± 149.0 kJ; 762.6 ± 141.1 kJ; P = 0.951). Pacing was also similar, with no differences in power output apparent during the experimental trials (P = 0.546). Core temperature (P = 0.615), heart rate (P = 0.505), ratings of perceived exertion (P = 0.181), and perceived thermal stress (P = 0.416) were not influenced by the nature of the intervention. Blood glucose concentrations were similar during the CHO and PLA trials (P = 0.117). In contrast to the findings of several studies undertaken in temperate conditions, the present investigation failed to support role of oral sensing of CHO in influencing performance during prolonged exercise in warm conditions.

Experimental evaluation of an automated endoscope reprocessor with in situ generation of peracetic acid for disinfection of semicritical devices.

PubMed

Sattar, Syed A; Kibbee, Richard J; Tetro, Jason A; Rook, Tony A

2006-11-01

To evaluate the effectiveness of a high-level disinfection solution generated inside an endoscope processing system for decontaminating external and internal surfaces of experimentally contaminated heat-sensitive medical devices. The American Society for Testing and Materials Simulated-Use Test protocol (E1837-02), which incorporates a soil load in each inoculum, was used to evaluate the efficacy of the system when processing 4 common types of endoscopes contaminated separately with 5 types of nosocomial pathogens: Pseudomonas aeruginosa (ATCC 15442), spores of Clostridium difficile (ATCC 9689), a glutaraldehyde-resistant strain of Mycobacterium chelonae, a vancomycin-resistant strain of Enterococcus faecalis, and a methicillin-resistant strain of Staphylococcus aureus. Rinse solution samples from channels and from surfaces of the processed endoscopes were tested for any microbicidal residues. For all organisms tested, the baseline level of contamination of the endoscopes ranged from 5 log(10) to greater than 7 log(10) at each external surface site and internal channel. All tests showed reductions in viability of the test organisms to undetectable levels. All rinse solution samples from external and internal sites of the endoscopes proved to be free of any residual microbicidal activity. The endoscope reprocessor, with its processor-generated high-level disinfection solution, successfully reduced the numbers of selected, clinically relevant pathogens to undetectable levels both in the channels and on the outside surfaces of the 4 representative endoscopes tested in this study.

Mechanical properties and leaching modeling of activated incinerator bottom ash in Portland cement blends.

PubMed

Onori, Roberta; Polettini, Alessandra; Pomi, Raffaella

2011-02-01

In the present study the evolution of mechanical strength and the leaching behavior of major and trace elements from activated incinerator bottom ash/Portland cement mixtures were investigated. Chemical and mechanical activation were applied with the purpose of improving the reactivity of bottom ash in cement blends. Chemical activation made use of NaOH, KOH, CaCl(2) or CaSO(4), which were selected for the experimental campaign on the basis of the results from previous studies. The results indicated that CaCl(2) exhibited by far the best effects on the evolution of the hydration process in the mixtures; a positive effect on mechanical strength was also observed when CaSO(4) was used as the activator, while the gain in strength produced by KOH and NaOH was irrelevant. Geochemical modeling of the leaching solutions provided information on the mineral phases responsible for the release of major elements from the hardened materials and also indicated the important role played by surface sorption onto amorphous Fe and Al minerals in dictating the leaching of Pb. The leaching of the other trace metal cations investigated (Cu, Ni and Zn) could not be explained by any pure mineral included in the thermodynamic database used, suggesting they were present in the materials in the form of complex minerals or phase assemblages for which no consistent thermodynamic data are presently available in the literature. Copyright © 2010 Elsevier Ltd. All rights reserved.

Effect of sonic and ultrasonic activation on organic tissue dissolution from simulated grooves in root canals using sodium hypochlorite and EDTA.

PubMed

Conde, A J; Estevez, R; Loroño, G; Valencia de Pablo, Ó; Rossi-Fedele, G; Cisneros, R

2017-10-01

To compare soft-tissue dissolution by sodium hypochlorite, with an EDTA intermediate rinse, with or without activation with passive ultrasonic activation (PUI) or sonic activation using the Endoactivator (EA) or Eddy tips (ED). The root canals of eighty-three human maxillary central incisors were chemo-mechanically prepared and the teeth split. A standardized longitudinal intracanal groove was created in one of the root halves. Eighty-three porcine palatal mucosa samples were collected, adapted to fit into the grooves and weighed. The re-assembled specimens were randomly divided into four experimental groups (n = 20), based on the final rinse: no activation; EA; PUI; ED, using 2.5% sodium hypochlorite, with an EDTA intermediate rinse. A control group (n = 3) was irrigated with distilled water without activation. The solutions were delivered using a syringe and needle 2 mm from working length. Total irrigation time was 150 s, including 60 s of activation in the specific groups. The study was carried out at 36 ± 2 °C. The porcine palatal mucosa samples were weighed after completion of the assays. Student paired t-test and anova were used to assess the intra- and intergroup weight changes. The multiple comparisons were evaluated using Bonferroni correction (α = 0.05). Weight loss occurred in all experimental groups. Irrigant activation resulted in greater weight loss when compared to the nonactivated group [vs. EA (P = 0.001); vs. PUI (P < 0.001); vs. ED (P < 0.001)]. No significant differences were found amongst the different activation systems. Activation increased the tissue-dissolving activity of irrigants from artificial grooves in root canals of maxillary central incisors. © 2016 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Microbiological evaluation of octenidine dihydrochloride mouth rinse after 5 days' use in orthodontic patients.

PubMed

Dogan, Alev Aksoy; Cetin, Emel Sesli; Hüssein, Emad; Adiloglu, Ali Kudret

2009-07-01

To determine the absolute and relative antibacterial activity of octenidine dihydrochloride (OCT) against total and cariogenic bacteria in saliva samples of patients with fixed orthodontic appliances during 5 days of usage. The study group consisted of 5 male and 13 female subjects who were selected from patients in the Clinic of Orthodontics. Each patient was given physiologic saline (PS), chlorhexidine gluconate (CHX), polyvinylpyrrolidone-iodine complex (PVP-I), and OCT every morning for 5 days, each separated by a 2-week interval. Total and cariogenic bacteria in saliva samples of orthodontically treated patients with fixed appliances were collected during 5 days of usage. Unstimulated saliva was collected as a baseline sample. Saliva samples were collected at 15 minutes, and on the second, third, and fifth day after rinsing the mouth with any of the solutions for 30 seconds, and bacterial counts were detected. OCT showed an ultimate reduction of total viable oral bacteria, Lactobacillus species, and Streptococcus mutans in vivo. OCT also had a significantly greater inhibitory effect than 0.2% CHX and 7.5% PVP-I, from the beginning of the study until the fifth day after the orthodontic appliances were bonded (P < .1). OCT compared favorably with respect to CHX and PVP-I complex in orthodontically treated patients with fixed appliances (P

Running Performance With Nutritive and Nonnutritive Sweetened Mouth Rinses.

PubMed

Hawkins, Keely R; Krishnan, Sridevi; Ringos, Lara; Garcia, Vanessa; Cooper, Jamie A

2017-09-01

Using mouth rinse (MR) with carbohydrate during exercise has been shown to act as an ergogenic aid. To investigate if nutritive or nonnutritive sweetened MR affects exercise performance and to assess the influence of sweetness intensity on endurance performance during a time trial (TT). This randomized, single-blinded study had 4 treatment conditions. Sixteen subjects (9 men, 7 women) completed a 12.8-km TT 4 different times. During each TT, subjects mouth-rinsed and expectorated a different solution at time 0 and every 12.5% of the TT. The 4 MR solutions were sucrose (S) (sweet taste and provides energy of 4 kcal/g), a lower-intensity sucralose (S1:1) (artificial sweetener that provides no energy but tastes sweet), a higher-intensity sucralose (S100:1), and water as control (C). Completion times for each TT, heart rate (HR), and ratings of perceived exertion (RPE) were also recorded. Completion time for S was faster than for C (1:03:47 ± 00:02:17 vs 1:06:56 ± 00:02:18, respectively; P < .001) and showed a trend to be faster vs S100:1 (1:03:47 ± 00:02:17 vs 1:05:38 ± 00:02:12, respectively; P = .07). No other TT differences were found. Average HR showed a trend to be higher for S vs C (P = .08). The only difference in average or maximum RPE was for higher maximum RPE in C vs S1:1 (P = .02). A sweet-tasting MR did improve endurance performance compared with water in a significant manner (mean 4.5% improvement; 3+ min.); however, the presence of energy in the sweet MR appeared necessary since the artificial sweeteners did not improve performance more than water alone.

Japanese Papilio butterflies puddle using Na+ detected by contact chemosensilla in the proboscis.

PubMed

Inoue, Takashi A; Hata, Tamako; Asaoka, Kiyoshi; Ito, Tetsuo; Niihara, Kinuko; Hagiya, Hiroshi; Yokohari, Fumio

2012-12-01

Many butterflies acquire nutrients from non-nectar sources such as puddles. To better understand how male Papilio butterflies identify suitable sites for puddling, we used behavioral and electrophysiological methods to examine the responses of Japanese Papilio butterflies to Na(+), K(+), Ca(2+), and Mg(2+). Based on behavioral analyses, these butterflies preferred a 10-mM Na(+) solution to K(+), Ca(2+), and Mg(2+) solutions of the same concentration and among a tested range of 1 mM to 1 M NaCl. We also measured the ion concentrations of solutions sampled from puddling sites in the field. Na(+) concentrations of the samples were up to 6 mM, slightly lower than that preferred by butterflies in the behavioral experiments. Butterflies that sipped the 10 mM Na(+) solution from the experimental trays did not continue to puddle on the ground. Additionally, butterflies puddled at sites where the concentrations of K(+), Ca(2+), and/or Mg(2+) were higher than that of Na(+). This suggests that K(+), Ca(2+), and Mg(2+) do not interfere with the detection of Na(+) by the Papilio butterfly. Using an electrophysiological method, tip recordings, receptor neurons in contact chemosensilla inside the proboscis evoked regularly firing impulses to 1, 10, and 100 mM NaCl solutions but not to CaCl(2) or MgCl(2). The dose-response patterns to the NaCl solutions were different among the neurons, which were classified into three types. These results showed that Japanese Papilio butterflies puddle using Na(+) detected by the contact chemosensilla in the proboscis, which measure its concentration.

Aggregation of TiO2-graphene nanocomposites in aqueous environment: Influence of environmental factors and UV irradiation.

PubMed

Hua, Zulin; Zhang, Jianan; Bai, Xue; Ye, Zhengfang; Tang, Zhiqiang; Liang, Lu; Liu, Yuqi

2016-01-01

The aggregation kinetics of TiO2-graphene nanocomposites in aqueous solution affected by solution pH, salt types (NaCl, CaCl2) and concentrations of electrolytes, and stability induced by UV irradiation was investigated in this study. The zeta potentials and hydrodynamic diameter of the nanoparticles were used as bases to assess the aggregation behavior, and stability of nanocomposites exposed to UV irradiation was expressed in terms of supernatant concentration. The aggregation of TiO2-graphene nanoparticles in aqueous media followed the colloidal theory. TiO2-graphene nanoparticles were significantly aggregated in the presence of a diavalent cation compared with monovalent cation because the former was more capable of effective charge screening and neutralization. The calculated Hamaker constant of the TiO2-graphene nanocomposites in aqueous solution prepared in the lab was 2.31×10(-20)J. The stability of this composite nanoparticles was between those of pure TiO2 and graphene. A known intensity of UV irradiation was beneficial in the formation of TiO2-graphene nanoparticle aggregates. However, prolonged UV irradiation may stabilize the nanoparticles. These results provided critical information about the colloidal properties of the new TiO2-graphene nanocomposites and were useful in predicting the fate and transport of TiO2-graphene nanocomposites in natural water environments. Copyright © 2015 Elsevier B.V. All rights reserved.

Cold-set hydrogels made of whey protein nanofibrils with different divalent cations.

PubMed

Mohammadian, Mehdi; Madadlou, Ashkan

2016-08-01

Whey protein nanofibrils are gaining interest to fabricate cold-set hydrogels due to their ability to gel at lower concentrations than parent proteins. In the present research, fibrillated protein solution was gelled with three different divalent cation salts including CaCl2, MnCl2 and ZnCl2 and the textural and functional characteristics of the resulting hydrogel samples were studied. Atomic force microscopy indicated that the flexible micron-scaled fibrils with nanometric thickness (up to 8.0nm) that formed at pH 2.0 underwent breaking in length upon post-formation pH rise to 7.5. Whilst heat-denatured protein solution failed to form self-supporting gel at pH 7.5, fibrillated protein solution gelled by all three types of cations. Fibrillation increased the protein solution consistency coefficient (K) much more than heat denaturation. It was suggested based on Fourier-transform infra-red (FT-IR) spectra that some hydrogen bonds were disrupted by fibrillation. Zn(2+)-induced gel was firmer, had a higher water holding capacity and a more compact microstructure, as well, required a higher compressive stress to fracture than its counterparts. Nonetheless, the Mn(2+)- and Ca(2+)-induced gels disintegrated to a much lesser extent in both pepsin-free and pepsin-present simulated gastric juice than Zn(2+)-induced sample. Chitosan coating approximately halved the simulated degradability of all gel samples. Copyright © 2016 Elsevier B.V. All rights reserved.

40 CFR 421.336 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

....000 499.500 (d) SiCl4 purification wet air pollution control. PSNS for the Primary Zirconium and....262 Lead 4.416 2.050 Nickel 8.674 5.835 Ammonia (as N) 2,102.000 895.800 (q) Leaching rinse water from... Nickel 32.410 21.810 Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy...

40 CFR 421.336 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

....000 499.500 (d) SiCl4 purification wet air pollution control. PSNS for the Primary Zirconium and....262 Lead 4.416 2.050 Nickel 8.674 5.835 Ammonia (as N) 2,102.000 895.800 (q) Leaching rinse water from... Nickel 32.410 21.810 Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy...

40 CFR 421.336 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

....000 499.500 (d) SiCl4 purification wet air pollution control. PSNS for the Primary Zirconium and....262 Lead 4.416 2.050 Nickel 8.674 5.835 Ammonia (as N) 2,102.000 895.800 (q) Leaching rinse water from... Nickel 32.410 21.810 Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy...

40 CFR 421.336 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

....000 499.500 (d) SiCl4 purification wet air pollution control. PSNS for the Primary Zirconium and....262 Lead 4.416 2.050 Nickel 8.674 5.835 Ammonia (as N) 2,102.000 895.800 (q) Leaching rinse water from... Nickel 32.410 21.810 Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy...

40 CFR 421.336 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

....000 499.500 (d) SiCl4 purification wet air pollution control. PSNS for the Primary Zirconium and....262 Lead 4.416 2.050 Nickel 8.674 5.835 Ammonia (as N) 2,102.000 895.800 (q) Leaching rinse water from... Nickel 32.410 21.810 Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy...

Evaluation of HPV-16 and HPV-18 specific antibody measurements in saliva collected in oral rinses and merocel® sponges.

PubMed

Parker, Katherine H; Kemp, Troy J; Pan, Yuanji; Yang, Zhen; Giuliano, Anna R; Pinto, Ligia A

2018-05-03

Current Human papillomavirus (HPV) L1 VLP vaccines protect against HPV-16 and HPV-18-associated cancers, in females and males. Although correlates of protection have not been identified, HPV-specific antibodies at sites of infection are thought to be the main mechanism of protection afforded by vaccination. Oral sampling has gained increased attention as a potential alternative to serum in monitoring immunity to vaccination and understanding local immunity in oral cancers. Serum was collected via venipuncture, and saliva was collected via oral rinses and Merocel® sponges from healthy volunteers: 16 unvaccinated females, 6 females (ages 24-41) and 6 mid-adult aged males (ages 27-45) recipients of three doses of the HPV-16/18/6/11 vaccine (Gardasil®). Mid-adult male vaccine trial participants were compared to female participants. Samples were tested for anti-HPV-16 and anti-HPV-18 immunoglobulin G levels by an L1 virus-like particle-based enzyme-linked immunosorbent assay (ELISA). All vaccinated participants had detectable serum anti-HPV-16 and anti-HPV-18 antibodies. Optimal standard concentration range and sample serial dilutions for oral rinses were determined. The standard curve was not affected by the type of solution examined. Reproducibility of HPV-16 and HPV-18 antibody titers in mouthwash (overall CV < 10%) or in Merocel® extraction buffer was robust (CV < 13%). Excellent assay linearity (R 2  > 0.9) was observed for sera spiked controls in both solutions. HPV-16 and HPV-18 specific antibodies were detectable in saliva from vaccine recipients, both in mouthwash and in Merocel® sponges but levels were several logs lower than those in serum. This study confirms the application of HPV-16 and HPV-18 ELISAs currently used in sero-epidemiological studies of immunogenicity of HPV vaccines for use with oral samples. Oral samples may be a useful resource for the detection of HPV-16 and HPV-18-specific antibodies in saliva following vaccination. Copyright © 2018 Elsevier Ltd. All rights reserved.

Soil fluoride fractions and their bioavailability to tea plants (Camellia sinensis L.).

PubMed

Yi, Xiaoyun; Qiao, Sha; Ma, Lifeng; Wang, Jie; Ruan, Jianyun

2017-10-01

Drinking teas containing high fluoride (F) imposes fluorosis risk. The soil F bioavailability is an important factor influencing its uptake and contents in teas. The present work was conducted to investigate F fractions in soil and their bioavailability to tea plants. Tea seedlings were cultivated on 6 typical soils treated with a mixture consisting of dolomite, lime, peat and KCl at variable rates in the pot experiment. Soils and young shoots were collected in pairs from 63 sites of 21 plantations in a field experiment. Soil fluoride was sequentially separated into hot water soluble [Formula: see text], exchangeable [Formula: see text] (by 1 mol L -1 MgCl 2 , pH = 7.0), F bound to Mn and Fe hydroxides [F (oxides,s) ], and organic matter [F (OM,s) ] or extracted independently by water [Formula: see text] or 0.01 mol L -1 CaCl 2 solution [Formula: see text]. Averaged [Formula: see text], [Formula: see text], F (oxides,s) and F (OM,s) accounted for 51, 14, 5 and 30 % of the total sequential extracts, respectively. There were significant correlations among [Formula: see text], [Formula: see text] and F (OM,s) . Fluoride contents in leaves correlated with [Formula: see text] (r = 0.71, p < 0.001), [Formula: see text] (r = 0.93, p < 0.001) and F (OM,s) (r = 0.69, p < 0.01) but not other fractions in the pot experiment and with [Formula: see text] (r = 0.43-0.57, p < 0.001) and [Formula: see text] (r = 0.42-0.79, p < 0.001) in the field experiment. It was concluded that 0.01 M CaCl 2 extractable fluoride can be a good indicator of soil F bioavailability to tea plants. The significant correlations among some of the F fractions suggested that F in solution, AlF complexes (AlF 2 + , AlF 2+ ) and those bound to organic matter likely represent the available pools to tea plants.

Whey protein isolate gel for separation: A formation, characterization, and application study

NASA Astrophysics Data System (ADS)

Teo, Jiunn Yeong

Novel microporous membranes made of whey protein isolate (WPI) were developed. Aggregates of WPI comprised the bulk of the membrane, the size and packing density of which were varied by changing CaCl2 concentration (0.05--0.3M) and WPI concentration (30--40wt%), respectively. Aggregate sizes of the membranes made with 0.3M, 0.1M, 0.05M CaCl2 were roughly 1.5mum, 1mum, and 0.8mum, respectively. Skin layer of thickness about 0.5mum was found on either side of the membrane, but the thickness could reach 5mum at 0.3M CaCl2. Additionally, the porosity of the skin layer was shown to be modifiable with the addition of surfactant. Membranes were stable in hexane with flux values on the order of 1--1000gal/ft 2·d depending on the morphology of the membrane. The molecular weight cutoffs (MWCOs) of the WPI membranes with skins were evaluated using two different methods: (i) dextran marker method and (ii) protein/vitamin marker method. Membranes were found to have MWCOs of 1,000 or greater with variations when the concentration of salt used to control aggregate size, or surfactant used to modify skin properties were selected. The microporous WPI gel was also used as a cation exchanger and a hydrophobic adsorbent. The WPI cation exchanger has a maximum capacity of 68mg cupric chloride per gram dry WPI gel at neutral pH and can be regenerated effectively by reducing the pH of the solution. The WPI gel has also been found to be an excellent adsorbent for total phenolic compounds from grape extract with a partition coefficient higher than 1000 in aqueous system. The mechanism for total phenolic compounds adsorption is believed to be physical sorption, particularly sorption/condensation of total phenolic compounds in the pores and on all surfaces of WPI gel. The gel has a low extractables of 1ng/ml.g gel, and has an isoelectric point of 5.5. Although WPI gel was made into a monolith for continuous bed chromatography, channeling problems have made it very hard to evaluate the performance of WPI monolith for continuous bed chromatography. Nonetheless the WPI monolith may be used to separate different protein molecules based on protein-protein interaction between WPI and protein molecules to be separated.

A randomised clinical evaluation of a fluoride mouthrinse and dentifrice in an in situ caries model.

PubMed

Parkinson, Charles R; Hara, Anderson T; Nehme, Marc; Lippert, Frank; Zero, Domenick T

2018-03-01

Fluoride mouthrinses provide advantages for fluoride delivery by maintaining elevated intra-oral fluoride concentrations following fluoride dentifrice use. This in situ caries study investigated potential anti-caries efficacy of a 220 ppm fluoride mouthrinse. This was an analyst-blinded, four-treatment, randomised, crossover study using partially demineralised, gauze-wrapped, human enamel samples mounted in a mandibular partial denture. Participants brushed twice daily for 14 days with either a 1150 ppm fluoride or a fluoride-free placebo dentifrice and either rinsed once daily with the 220 ppm fluoride mouthrinse or not. Following each treatment period, percent surface microhardness recovery (%SMHR) and enamel fluoride uptake (EFU) were assessed. Fifty three participants completed the study. Compared with the placebo dentifrice/no rinse treatment, the fluoride-containing regimens demonstrated greater enamel remineralisation (%SMHR) and fluoridation (EFU): fluoride dentifrice/fluoride rinse (%SMHR difference: 21.55 [95% CI: 15.78,27.32]; EFU difference 8.35 [7.21,9.29]); fluoride dentifrice/no rinse: 19.48 [13.81,25.15]; 6.47 [5.35,7.60]; placebo dentifrice/fluoride rinse: 16.76 [11.06,22.45]; 5.87 [4.72,7.00] (all P < .0001). There were no significant differences in%SMHR between fluoride regimens. The fluoride dentifrice/fluoride rinse regimen was associated with higher EFU than the fluoride dentifrice/no rinse (1.88 [0.75,3.01], P = .0013) and placebo dentifrice/fluoride rinse regimens (2.48 [1.34,3.62], P < .0001). Treatments were generally well-tolerated. The in situ caries model demonstrated that the fluoride mouthrinse is effective in promoting enamel caries lesion remineralisation and fluoridation whether used following a fluoride or non-fluoride dentifrice. Additive (potential) anti-caries benefits of a fluoride rinse after a fluoride dentifrice were confined to enhancements in lesion fluoridation (EFU). In conjunction with a fluoride dentifrice, fluoride mouthrinses enhance enamel fluoridation, which may be useful in caries prevention. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Metal-rich fluid inclusions provide new insights into unconformity-related U deposits (Athabasca Basin and Basement, Canada)

NASA Astrophysics Data System (ADS)

Richard, Antonin; Cathelineau, Michel; Boiron, Marie-Christine; Mercadier, Julien; Banks, David A.; Cuney, Michel

2016-02-01

The Paleoproterozoic Athabasca Basin (Canada) hosts numerous giant unconformity-related uranium deposits. The scope of this study is to establish the pressure, temperature, and composition (P-T-X conditions) of the brines that circulated at the base of the Athabasca Basin and in its crystalline basement before, during and after UO2 deposition. These brines are commonly sampled as fluid inclusions in quartz- and dolomite-cementing veins and breccias associated with alteration and U mineralization. Microthermometry and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) data from five deposits (Rabbit Lake, P-Patch, Eagle Point, Millennium, and Shea Creek) complement previously published data for the McArthur River deposit. In all of the deposits investigated, fluid inclusion salinity is between 25 and 40 wt.% NaCl equiv., with compositions displaying a continuum between a "NaCl-rich brine" end-member (Cl > Na > Ca > Mg > K) and a "CaCl2-rich brine" end-member (Cl > Ca ≈ Mg > Na > K). The CaCl2-rich brine has the highest salinity and shows evidence for halite saturation at the time of trapping. The continuum of compositions between the NaCl-rich brine and the CaCl2-rich brine end-members combined with P-T reconstructions suggest anisothermal mixing of the two brines (NaCl-rich brine, 180 ± 30 °C and 800 ± 400 bars; CaCl2-rich brine, 120 ± 30 °C and 600 ± 300 bars) that occurred under fluctuating pressure conditions (hydrostatic to supra-hydrostatic). However, because the two brines were U bearing and therefore oxidized, brine mixing was probably not the driving force for UO2 deposition. Several scenarios are put forward to account for the Cl-Na-Ca-Mg-K composition of the brines, involving combinations of seawater evaporation, halite dissolution, mixing with a halite-dissolution brine, Mg/Ca exchange by dolomitization, Na/Ca exchange by albitization of plagioclase, Na/K exchange by albitization of K-feldspar, and Mg loss by Mg-rich alteration. Finally, the metal concentrations in the NaCl-rich and CaCl2-rich brines are among the highest recorded compared to present-day sedimentary formation waters and fluid inclusions from basin-hosted base metal deposits (up to 600 ppm U, 3000 ppm Mn, 4000 ppm Zn, 6000 ppm Cu, 8000 ppm Pb, and 10,000 ppm Fe). The CaCl2-rich brine carries up to one order of magnitude more metal than the NaCl-rich brine. Though the exact origin of major cations and metals of the two brines remains uncertain, their contrasting compositions indicate that the two brines had distinct flow paths and fluid-rock interactions. Large-scale circulation of the brines in the Athabasca Basin and Basement was therefore a key parameter for metal mobility (including U) and formation of unconformity-related U deposits.

Automated Immunomagnetic Separation and Microarray Detection of E. coli O157:H7 from Poultry Carcass Rinse

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, Darrell P.; Brown, Jeremy D.; Call, Douglas R.

2001-09-01

We describe the development and application of a novel electromagnetic flow cell and fluidics system for automated immunomagnetic separation of E. coli directly from unprocessed poultry carcass rinse, and the biochemical coupling of automated sample preparation with nucleic acid microarrays without cell growth. Highly porous nickel foam was used as a magnetic flux conductor. Up to 32% recovery efficiency of 'total' E. coli was achieved within the automated system with 6 sec contact times and 15 minute protocol (from sample injection through elution), statistically similar to cell recovery efficiencies in > 1 hour 'batch' captures. The electromagnet flow cell allowedmore » complete recovery of 2.8 mm particles directly from unprocessed poultry carcass rinse whereas the batch system did not. O157:H7 cells were reproducibly isolated directly from unprocessed poultry rinse with 39% recovery efficiency at 103 cells ml-1 inoculum. Direct plating of washed beads showed positive recovery of O 157:H7 directly from carcass rinse at an inoculum of 10 cells ml-1. Recovered beads were used for direct PCR amplification and microarray detection, with a process-level detection limit (automated cell concentration through microarray detection) of < 103 cells ml-1 carcass rinse. The fluidic system and analytical approach described here are generally applicable to most microbial detection problems and applications.« less

Comparison of the solubilizing efficiencies of some pH lowering (sulphur and (NH4)2SO4) amendments on Cd and Zn mobility in soils.

PubMed

Amoakwah, Emmanuel; Van Slycken, Stijn; Essumang, David K

2014-08-01

The use of conventional methods to clean up the soil is very expensive and destructive to the ecosystem. The concept of phytoextraction has been introduced to safely manage soils contaminated with heavy metals. However, using plants to remediate polluted soils is a lengthy process. This has necessitated the use of amendments to potentially enhance solubilization of metals in order to increase their bioavailability in the soil solution. A pot experiment was conducted to study the effect of some selected pH lowering amendments [elemental sulphur and (NH4)2SO4] on the solubility and availability of Cd and Zn. The application of these amendments resulted in a decrease in the pH of the soil. The decrease in pH significantly enhanced the solubilization and the mobility of Cd and Zn into the soil solution. The CaCl2 extraction protocol was employed to study the effects of the various amendments on the mobility of Cd and Zn.

The effectiveness of organic PCM based on lauric acid from coconut oil and inorganic PCM based on salt hydrate CaCl2.6H2o as latent heat energy storage system in Indonesia

NASA Astrophysics Data System (ADS)

U, Sri Rahayu A.; Putri, Widya A.; Sutjahja, I. M.; Kurnia, D.; Wonorahardjo, S.

2016-08-01

A latent heat energy storage system utilizing phase change materials (PCM) is an alternative strategy to reduce the use of Air Conditioning (AC) system in big cities in Indonesia in order for energy conservation in the future. In this research we used two kinds of materials, namely organic PCM based on lauric acid from coconut oil (CO) and inorganic PCM based on salt hydrate CaCl2.6H2O, because they have thermophysical parameters suitable for human's thermal comfort application in the building. The CO which contained more than 50% lauric acid has the melting temperature (Tm ) of about 26 °C and heat entalphy (ΔH) around 103 kJ/kg, while CaCl2.6H2O has the melting point of 29 °C and heat entalphy of 190 kJ/kg. In this paper we report the effectiveness of those two kinds of PCM in reducing the air temperature as one of some criteria for human's thermal comfort. The experiments were performed in a close and adiabatic room and the time-temperature measurements were done automatically using Arduino microcontroller and LM35 temperature sensor connected to the PC.

[Hydrogen peroxide, chloramine T and chlorhexidrine in the disinfection of acrylic resin].

PubMed

Czerwińska, W; Kedzia, A; Kałowski, M

1978-01-01

The effectiveness of 3% h drogen peroxide, 5% chloramine T and 0,5% chlorhexidine gluconate solutions in disinfection of acrylic resine plates massively infected with oral flora was analysed. The acrylic resine plates used for investigations, were infected in vitro with mixed salivary flora characterized by small numbers of yeast-like fungi (1st group), or great number of these microorganisms (2nd group). Infected plates were exposed to solutions of analysed disinfectants during various time periods. After rinsing or inactivation of disinfectant residues, acrylic plates were put into bacteriological medium and incubated during 7 days period in 37 degrees C. The results of this study indicated the effectiveness of acrylic plates disinfection to be dependent on used disinfectant, time of exposition, and microorganisms present on the surface of acrylic resine. The solutions of disinfectants were less active in the cases of plates infected with material containing great numbers of yeast-like microorganisms. Among analysed disinfectants 0,5% solution of chlorhexidine was characterized by most effective and rapid activity, whereas 3% solution of hydrogen peroxide was found to be the least effective.

Protoplasmic Swelling as a Symptom of Freezing Injury in Onion Bulb Cells 1

PubMed Central

Arora, Rajeev; Palta, Jiwan P.

1986-01-01

Freezing injury, in onion bulb tissue, is known to cause enhanced K+ efflux accompanied by a small but significant loss of Ca2+ following incipient freezing injury and swelling of protoplasm during the postthaw secondary injury. The protoplasmic swelling of the cell is thought to be caused by the passive influx of extracellular K+ into the cell followed by water uptake. Using outer epidermal layer of unfrozen onion bulb scales (Allium cepa L. cv Big Red), we were able to stimulate the irreversible freezing injury symptoms, by bathing epidermal cells in 50 millimolar KCl. These symptoms were prevented by adding 20 millimolar CaCl2 to the extracellular KCl solution. Our results provide evidence that loss of cellular Ca2+ plays an important role in the initiation and the progression of freezing injury. Images Fig. 1 PMID:16665083

Thermal and Optical Properties of New Poly(amide-imide)/Nanocomposite Reinforced by Layer Silicate Containing Diphenyl Ether Moieties

NASA Astrophysics Data System (ADS)

Faghihi, Khalil; Faramarzi, Ellahe; Shabanian, Meisam

2011-04-01

New poly(amide-imide)-montmorillonite reinforced nanocomposites containing Bis(4-N-trimellitylimido) diphenyl ether moiety in the main chain were synthesized by a convenient solution intercalation technique. Poly(amide-imide) (PAI) 4 was synthesized by the direct polycondensation reaction of Bis(4-N-trimellitylimido) diphenyl ether 3 with 4,4'-diamino diphenyl ether 2 in the presence of triphenyl phosphite (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). Morphology and structure of the resulting PAI-nanocomposite films 4a and 4b with 10 and 20 mass% silicate particles respectively, were characterized by FT-IR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The properties of nanocomposites films were investigated by using Uv-vis spectroscopy, thermogravimetric analysis (TGA) and water uptake measurements.

Stable thermosensitive in situ gel-forming systems based on the lyophilizate of chitosan/α,β-glycerophosphate salts.

PubMed

Wu, Guanghao; Yuan, Yuan; He, Jintian; Li, Ying; Dai, Xiaojing; Zhao, Baohua

2016-09-10

In the present study, lyophilization was attempted to improve the long-term storage of CS/GP thermogelling systems for biopharmaceutical applications. After lyophilization, CS/α,β-GP lyophilizate could not be dissolved in water, but some metal salts, such as NaCl, CaCl2, and MgCl2 surprisingly facilitated its dissolution. X-ray powder diffraction analysis suggested that calcium ions might preferentially form salts with α,β-GP, inhibit the transfer of protons from CS to α,β-GP, and then inhibit the aggregation of CS molecules during lyophilization. Comparison of the freshly prepared CS/α,β-GP/salt solutions and the reconstituted solutions from lyophilizates showed that lyophilization clearly influenced the properties of reconstituted CS/α,β-GP/salt solutions such as gelation time, viscosity, and pH. Furthermore, the reconstituted CS/α,β-GP/CaCl2 solutions maintained thermogelling properties and formed hydrogels at 37°C within approximately 5min, but did not form hydrogels at 20°C and 4°C over 2 weeks. The model protein bovine serum albumin (BSA) was further incorporated into the CS/α,β-GP/CaCl2 system. In vitro release experiments showed the sustained release of BSA from CS/α,β-GP/CaCl2 hydrogels in a pH-sensitive manner, demonstrating that CS/α,β-GP/CaCl2 may be useful as an in situ gel-forming system. Copyright © 2016 Elsevier B.V. All rights reserved.

In vitro dentin permeability after application of Gluma® desensitizer as aqueous solution or aqueous fumed silica dispersion

PubMed Central

ISHIHATA, Hiroshi; FINGER, Werner J.; KANEHIRA, Masafumi; SHIMAUCHI, Hidetoshi; KOMATSU, Masashi

2011-01-01

Objectives To assess and to compare the effects of Gluma® Desensitizer (GDL) with an experimental glutaraldehyde and HEMA containing fumed silica dispersion (GDG) on dentin permeability using a chemiluminous tracer penetration test. Material and Methods Twenty disc-shaped dentin specimens were dissected from extracted human third molars. The dentin specimens were mounted in a split chamber device for determination of permeability under liquid pressure using a photochemical method. Ten specimens were randomly selected and allocated to the evaluation groups Gluma® Desensitizer as aqueous solution and glutaraldehyde/HEMA as fumed silica dispersion, respectively. Dentin disc permeability was determined at two pressure levels after removal of smear with EDTA, after albumin soaking, and after application of the desensitizing agents. Two desensitizer-treated and rinsed specimens of each group were examined by scanning electron microscopy (SEM) for surface remnants. Results Comparatively large standard deviations of the mean EDTA reference and albumin soaked samples permeability values reflected the differences of the dentin substrates. The mean chemiluminescence values of specimen treated with GDL and GDG, respectively, were significantly reduced after topical application of the desensitizing agents on albumin-soaked dentin. The effects of GDL and GDG on permeability were not significantly different. Treated specimens showed no surface remnants after rinsing. Conclusions The experimental desensitizer gel formulation reduced dentin permeability as effectively as the original Gluma® Desensitizer solution. PMID:21552716

Raman spectroscopic studies of chemical speciation in calcium chloride melts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Windisch, Charles F.; Lavender, Curt A.

2005-02-01

Raman spectroscopy was applied to CaCl2 melts at 900 degrees C under both non-electrolyzed and electrolyzed conditions. The later used titania cathodes supplied by TIMET, Inc. and graphite anodes. Use of pulse-gating to collect the Raman spectra successfully eliminated any interference from black-body radiation and other stray light. The spectrum of molten CaCl2 exhibited no distinct, resolvable bands that could be correlated with a calcium chloride complex similar to MgCl42- in MgCl2 melts. Rather, the low frequency region of the spectrum was dominated by a broad “tail” arising from collective oscillations of both charge and mass in the molten saltmore » “network.” Additions of both CaO and Ca at concentrations of a percent or two resulted in no new features in the spectra. Addition of CO2, both chemically and via electrolysis at concentrations dictated by stability and solubility at 900 degrees C and 1 bar pressure, also produced no new bands that could be correlated with either dissolved CO2 or the carbonate ion. These results indicated that Raman spectroscopy, at least under the conditions evaluated in the research, was not well suited for following the reactions and coordination chemistry of calcium ions, nor species such as dissolved metallic Ca and CO2 that are suspected to impact current efficiency in titanium electrolysis cells using molten CaCl2. Raman spectra of TIMET titania electrodes were successfully obtained as a function of temperature up to 900 degrees C, both in air and in-situ in CaCl2 melts. However, spectra of these electrodes could only be obtained when the material was in the unreduced state. When reduced, either with hydrogen or within an electrolysis cell, the resulting electrodes exhibited no measurable Raman bands under the conditions used in this work.« less

A caffeine-maltodextrin mouth rinse counters mental fatigue.

PubMed

Van Cutsem, Jeroen; De Pauw, Kevin; Marcora, Samuele; Meeusen, Romain; Roelands, Bart

2018-04-01

Mental fatigue is a psychobiological state caused by prolonged periods of demanding cognitive activity that has negative implications on many aspects in daily life. Caffeine and carbohydrate ingestion have been shown to be able to reduce these negative effects of mental fatigue. Intake of these substances might however be less desirable in some situations (e.g., restricted caloric intake, Ramadan). Rinsing caffeine or glucose within the mouth has already been shown to improve exercise performance. Therefore, we sought to evaluate the effect of frequent caffeine-maltodextrin (CAF-MALT) mouth rinsing on mental fatigue induced by a prolonged cognitive task. Ten males (age 23 ± 2 years, physical activity 7.3 ± 4.3 h/week, low CAF users) performed two trials. Participants first completed a Flanker task (3 min), then performed a 90-min mentally fatiguing task (Stroop task), followed by another Flanker task. Before the start and after each 12.5% of the Stroop task (eight blocks), subjects received a CAF-MALT mouth rinse (MR: 0.3 g/25 ml CAF: 1.6g/25 ml MALT) or placebo (PLAC: 25 ml artificial saliva). Self-reported mental fatigue was lower in MR (p = 0.017) compared to PLAC. Normalized accuracy (accuracy first block = 100%) was higher in the last block of the Stroop in MR (p = 0.032) compared to PLAC. P2 amplitude in the dorsolateral prefrontal cortex (DLPFC) decreased over time only in PLAC (p = 0.017). Frequent mouth rinsing during a prolonged and demanding cognitive task reduces mental fatigue compared to mouth rinsing with artificial saliva.

Oral health care for pregnant and postpartum women.

PubMed

Goldie, M Perno

2003-08-01

Pregnancy may pose a number of concerns to the mother and the foetus. This can include systemic and oral issues that effect health. Transmission of caries-causing bacteria is one problem that can be minimized by utilizing simple, cost-effective measures. Chlorhexidine rinses and xylitol containing chewing gum will be discussed as possible solutions to this tremendous public health problem.

Metals Analyzer. User’s Manual

DTIC Science & Technology

1996-06-01

larger port diameters than the three reagent ports: matrix, psa acid and rinse acid (to minimize reagent diffusion into the cell solution). The... ferule repositioned (can be optionally replaced if unsuccessful in achieving a seal). The system must be completely watertight before proceeding to the...and concentrations (extrememly acidic and/or hazardous material), use of protective eyewear and safety gloves is recommended during the reagent

Foliar sorption of emerging and priority contaminants under controlled conditions.

PubMed

Calderón-Preciado, Diana; Matamoros, Víctor; Biel, Carmen; Save, Robert; Bayona, Josep M

2013-09-15

Agricultural irrigation water contains a variety of contaminants that can be introduced into the food chain through intake by irrigated crops. This paper describes an experiment under controlled conditions designed to simulate sprinkle irrigation with polluted water at two different relative humidities (40 and 90%). Specifically, shed lettuce-heart leaves were spiked with an aqueous solution containing organic microcontaminants, including pharmaceuticals (ibuprofen, diclofenac, clofibric acid, and carbamazepine), fragrances (tonalide), biocides (triclosan), insecticides (lindane), herbicides (atrazine), phenolic estrogen (bisphenol A), and polycyclic aromatic hydrocarbons (phenanthrene and pyrene). Following an incubation period (48 h), the treated leaves were rinsed with water, and both the solution used to rinse them and the leaves themselves were independently analyzed to investigate the foliar sorption and uptake of the spiked organic contaminants through cuticle. The results showed that the foliar sorption of emerging and priority microcontaminants in leaves wetted by irrigation practices is related to their polarity (logD(ow)) and volatility (logk(H)), regardless of their compound class and the relative humidity. The results thus underscore the need to improve the quality of reclaimed water in crop irrigation, particularly when sprinkle irrigation is used. Copyright © 2013 Elsevier B.V. All rights reserved.

Effects of a non-rinse conditioner on the enamel of primary teeth.

PubMed

Fava, Marcelo; Myaki, Silvio Issáo; Arana-Chavez, Victor Elias; Fava-de-Moraes, Flavio

2003-01-01

The aim of this in vitro study was to evaluate by scanning electron microscopy the morphological aspects of the enamel of primary teeth after etching with 36% phosphoric acid or a non-rinse conditioner. Ten naturally exfoliated anterior primary teeth were selected. The samples were subjected to prophylaxis with pumice paste and water using a low-speed hand piece. Etching was done on the buccal surface. Specimens were divided into 2 groups: G1 (n=10): etching with 36% phosphoric acid gel - Conditioner 36 (Dentsply) for 20 s, followed by water rinse for 15 s; G2 (n=10): etching with NRC - Non Rinse Conditioner (Dentsply) for 20 s, followed by air drying for 15 s. The samples were dehydrated, mounted on metal stubs, coated with gold and observed with Jeol JSM-6100 scanning electron microscope. Electron-micrographic analysis showed that both etching agents were effective for etching the enamel of primary teeth causing the formation of microporosities on the enamel surface, although the etching pattern was more effective with the use of 36% phosphoric acid gel.

The effect of a calcium phosphate mouth rinse on (chemo) radiation induced oral mucositis in head and neck cancer patients: a prospective study.

PubMed

Stokman, M A; Burlage, F R; Spijkervet, F K L

2012-08-01

Promising results of a calcium phosphate (CP) mouth rinse on reduced severity of oral mucositis have been reported. The aim of this study was to determine the effect of a CP mouth rinse on the frequency, duration and severity of (chemo) radiation induced oral mucositis in patients with head-neck cancer. patients with oral malignancies, treated with (chemo) radiotherapy, were included. Patients rinsed four times a day with a CP mouth rinse. Patients not willing to rinse with the CP mouth rinse served as control. Mucositis was scored according to the WHO score at baseline and twice a week during the full course of (chemo) radiotherapy. Patient's self-reported mouth-throat soreness (MTS) was evaluated at the same time interval using a diary in the CP mouth rinse group. The outcomes on MTS were compared with a historical control group. Fifty-two patients were analysed: 25 CP mouth rinse group, 11 control group and 16 historical group. There was no significant difference between the CP group and control group on development and severity of oral mucositis. No significant difference was found for subjective outcomes on MTS between the CP group and the historical group. The CP mouth rinse seems to have no influence on the frequency, duration and severity of oral mucositis during (chemo) radiation in patients with head and neck cancer. A trend to develop less MTS for drinking and eating was found when applying the CP mouth rinse. © 2012 John Wiley & Sons A/S.

Effect of exchangeable cation concentration on sorption and desorption of dissolved organic carbon in saline soils.

PubMed

Setia, Raj; Rengasamy, Pichu; Marschner, Petra

2013-11-01

Sorption is a very important factor in stabilization of dissolved organic carbon (DOC) in soils and thus C sequestration. Saline soils have significant potential for C sequestration but little is known about the effect of type and concentration of cations on sorption and release of DOC in salt-affected soils. To close this knowledge gap, three batch sorption and desorption experiments were conducted using soils treated with solutions either low or high in salinity. In Experiment 1, salinity was developed with either NaCl or CaCl2 to obtain an electrical conductivity (EC) in a 1:5 soil: water extract (EC1:5) of 2 and 4 dS m(-1). In Experiments 2 and 3, NaCl and CaCl2 were added in various proportions (between 25 and 100%) to obtain an EC1:5 of 0.5 and 4 dS m(-1), respectively. At EC1:5 of 4 dS m(-1), the sorption of DOC (derived from wheat straw) was high even at a low proportion of added Ca(2+) and did not change with proportion of Ca added, but at EC1:5 of 0.5 dS m(-1) increasing proportion of Ca(2+) added increased DOC sorption. This can be explained by the differences in exchangeable Ca(2+) at the two salinity levels. At EC1:5 of 4 dS m(-1), the exchangeable Ca(2+) concentration did not increase beyond a proportion of 25% Ca(2+), whereas it increased with increasing Ca(2+) proportion in the treatments at EC1:5 of 0.5 dS m(-1). The DOC sorption was lowest with a proportion of 100% as Na(+). When Ca(2+) was added, DOC sorption was highest, but least was desorbed (with deionised water), thus sorption and desorption of added DOC were inversely related. The results of this study suggest that DOC sorption in salt-affected soils is mainly controlled by the levels of exchangeable Ca(2+) irrespective of the Ca(2+) concentration in the soil solution which has implications on carbon stabilization in salt-affected soils. Copyright © 2013 Elsevier B.V. All rights reserved.

Assessing the impact of egg sweating on Salmonella Enteritidis penetration into shell eggs.

PubMed

Gradl, Janet A; Curtis, Patricia A; Jones, Deana R; Anderson, Kenneth E

2017-07-01

Salmonella Enteritidis (SE) prevalence in eggs is a major concern to the egg industry. Some research has shown that egg sweating can increase Salmonella penetration into egg contents when refrigerated eggs are moved to a warmer temperature. This occurs when eggs are tempered before wash, to minimize thermal cracks. The effect of egg sweating on SE penetration into shell eggs over a 6 week storage period at 4°C was assessed. A 2 × 2 factorial of SE inoculation and egg sweating was utilized. Treatments included (SES) nalidixic acid (NA)-resistant SE inoculated and sweated, (SENS) NA-resistant SE inoculated and not sweated, (NSES) buffered peptone water (BPW) inoculated and sweated, and (NSENS) BPW inoculated and not sweated. Eggs were inoculated with 108 SE. Eggs formed condensation for approximately 17 min in a 32°C incubator. Shell rinse, shell emulsion, and egg contents were sampled then enumerated and assessed for prevalence of SE over a 6 wk storage period at 4°C. After wk 1, the SENS shell rinse had higher SE counts (0.32 log10 CFU/mL) than the other 3 treatments, where no SE was enumerated. A significant week by treatment interaction was found for the shell rinse SE detection (P < 0.05). In subsequent weeks, no SE counts were obtained from the egg shell rinse, shell emulsion, or egg contents. The SENS shell rinses had significantly higher SE prevalence than the SES rinses in weeks 1 (100% vs. 34.3%), 2 (57.6% vs. 22.2%), and 3 (38.2% vs. 11.1%) (P < 0.05). In samples from weeks 4, 5, and 6, there was no difference in SE prevalence between SES and SENS. Egg sweating did not increase SE penetration into the shell emulsion across treatment or week (P < 0.05). The decreasing trend of SE prevalence obtained over the study period indicate that refrigeration is effective at inhibiting SE growth. These results indicate that egg sweating occurring under common US egg handling practices is not harmful to egg safety. © 2017 Poultry Science Association Inc.

40 CFR 421.333 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 2.387 1.108 Nickel 4.688 3.154 Ammonia (as N) 1,136.000 499.500 (d) SiCl4 purification wet air....674 5.835 Ammonia (as N) 2,102.000 895.000 (q) Leaching rinse water from zirconium metal production... Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy production. BAT...

40 CFR 421.333 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 2.387 1.108 Nickel 4.688 3.154 Ammonia (as N) 1,136.000 499.500 (d) SiCl4 purification wet air....674 5.835 Ammonia (as N) 2,102.000 895.000 (q) Leaching rinse water from zirconium metal production... Ammonia (as N) 7,856.000 3,453.000 (r) Leaching rinse water from zirconium alloy production. BAT...

Effect of enamel etching time on roughness and bond strength.

PubMed

Barkmeier, Wayne W; Erickson, Robert L; Kimmes, Nicole S; Latta, Mark A; Wilwerding, Terry M

2009-01-01

The current study examined the effect of different enamel conditioning times on surface roughness and bond strength using an etch-and-rinse system and four self-etch adhesives. Surface roughness (Ra) and composite to enamel shear bond strengths (SBS) were determined following the treatment of flat ground human enamel (4000 grit) with five adhesive systems: (1) Adper Single Bond Plus (SBP), (2) Adper Prompt L-Pop (PLP), (3) Clearfil SE Bond (CSE), (4) Clearfil S3 Bond (CS3) and (5) Xeno IV (X4), using recommended treatment times and an extended treatment time of 60 seconds (n = 10/group). Control groups were also included for Ra (4000 grit surface) and SBS (no enamel treatment and Adper Scotchbond Multi-Purpose Adhesive). For surface roughness measurements, the phosphoric acid conditioner of the SBP etch-and-rinse system was rinsed from the surface with an air-water spray, and the other four self-etch adhesive agents were removed with alternating rinses of water and acetone. A Proscan 2000 non-contact profilometer was used to determine Ra values. Composite (Z100) to enamel bond strengths (24 hours) were determined using Ultradent fixtures and they were debonded with a crosshead speed of 1 mm/minute. The data were analyzed with ANOVA and Fisher's LSD post-hoc test. The etch-and- rinse system (SBP) produced the highest Ra (microm) and SBS (MPa) using both the recommended treatment time (0.352 +/- 0.028 microm and 40.5 +/- 6.1 MPa) and the extended treatment time (0.733 +/- 0.122 microm and 44.2 +/- 8.2 MPa). The Ra and SBS of the etch-and-rinse system were significantly greater (p < 0.05) than all the self-etch systems and controls. Increasing the treatment time with phosphoric acid (SBP) and PLP produced greater surface roughness (p < 0.05) but did not result in significantly higher bond strengths (p > 0.05).

Preparation of novel alginate based anion exchanger from Ulva japonica and its application for the removal of trace concentrations of fluoride from water.

PubMed

Paudyal, Hari; Pangeni, Bimala; Inoue, Katsutoshi; Kawakita, Hidetaka; Ohto, Keisuke; Ghimire, Kedar Nath; Alam, Shafiq

2013-11-01

A green seaweed, Ulva japonica, was modified by loading multivalent metal ions such as Zr(IV) and La(III) after CaCl2 cross-linking to produce metal loaded cross-linked seaweed (M-CSW) adsorbents, which were characterized by elemental analysis, functional groups identification, and metal content determination. Maximum sorption potential for fluoride was drastically increased after La(III) and Zr(IV) loading, which were evaluated as 0.58 and 0.95 mmol/g, respectively. Loaded fluoride was quantitatively desorbed by using dilute alkaline solution for its regeneration. Mechanism of fluoride adsorption was inferred in terms of ligand exchange reaction between hydroxyl ion on co-ordination sphere of the loaded metal ions of M-CSW and fluoride ion in aqueous solution. Application of M-CSW for the treatment of actual waste plating solution exhibited successful removal of fluoride to clear the effluent and environmental standards in Japan, suggesting high possibility of its application for the treatment of fluoride rich waste water. Copyright © 2013 Elsevier Ltd. All rights reserved.