A New Method for the Determination of Annual Sediment Fluxes from Varved Lake Sediments

NASA Astrophysics Data System (ADS)

Francus, P.; Massa, C.; Lapointe, F.

2013-12-01

Calculation of sediment mass accumulation rates instead of thickness accumulation is preferable for paleoclimatic reconstruction as it eliminates the effects of dilution and compaction. Annually laminated lake sediment sequences (varved) theoretically allow for the estimation of sediment fluxes at annual scale, but the calculation is limited by discrete bulk density measurements, often carried out at a much lower resolution (usually 1 cm) than the varves (ranging from 0.07 to 27.3 mm, average 1.84 mm according to Ojala et al. 2012). Since many years the development of automated logging instruments made available continuous and high resolution sediment property data, in a non-destructive fashion. These techniques can easily be used to extract the physical and chemical parameters of sediments at the varve scale (down to 100 μm). Here we present a robust method to calculate annual sediment fluxes from varved lake sediments by combining varves thickness measurements to core logging data, and provide an example for its applications. Several non-destructive densitometric methods applied to the Strathcona Lake sediment, northern Ellesmere Island, Canada (78°33'N; 82°05'W) were compared: Hounsfield Units from a CT-Scan, coherent/incoherent ratio and X-ray radiography (of both split core and sediment slabs, from an Itrax core Scanner), and gamma ray attenuation density. Core logging data were statistically compared to 400 discrete measurements of dry bulk density, wet bulk density and water content performed at 2 mm contiguous intervals. A very strong relationship was found between X-ray grey level on sediment slab and dry bulk density. Relative X-ray densities, at 100μm resolution, were then successfully calibrated against real densities. The final step consisted in binning the calibrated densities to the corresponding varve thickness and then to calculate the annual mass accumulation rates by multiplying the two parameters for each varve year. Strathcona Lake is located directly downstream of the Agassiz ice cap and contains laminated sediments whose accumulation is directly related to hydrological inputs generated by the melting of the ice cap. Over the last 65 years, annual sediment accumulation rates in Strathcona Lake documented an increase in high-energy hydrologic discharge events from 1990 to 2009. This timing is in agreement with evidence for an increase in the amount of melt on the adjacent Agassiz Ice Cap, as recorded in ice cores. A good correspondence was also found between annual mass accumulation rates and Eureka air temperature records, suggesting that temperature changes affected the extent of summer melting on the Agassiz Ice Cap, leading to high sediment yield to Strathcona Lake. Ojala, A.E.K., Francus, P., Zolitschka, B., Besonen, M. and Lamoureux, S.F. (2012) Characteristics of sedimentary varve chronologies - A review. Quaternary Science Reviews, 43, 45-60.

Constant Flux Proxies and Pleistocene Sediment Accumulation Rates on the Juan de Fuca Ridge in the Northeast Pacific

NASA Astrophysics Data System (ADS)

Middleton, J. L.; Mukhopadhyay, S.; Langmuir, C. H.; Costa, K.; McManus, J. F.; d'Almeida, M.; Huybers, P. J.; Winckler, G.

2016-12-01

Mass accumulation rates of marine sediments are often employed to constrain deposition rates of important proxies such as terrigenous dust, carbonate, and biogenic opal to quantitatively examine variations in continental aridity, atmospheric transport, and biologic productivity across changing climatic conditions. However, deposition rates that are estimated using traditional mass accumulation rates calculated from sediment core age models can be subject to bias from lateral sediment transport and limited age model resolution. Constant flux proxies, such as extraterrestrial helium-3 (3HeET) and excess thorium-230 (230ThXS), can be used to calculate vertical sediment accumulation rates that are independent of age model uncertainties and the effects of lateral sediment transport. While a short half-life limits analyses of 230ThXS to the past 500 ka, 3HeET is stable and could be used to constrain sedimentary fluxes during much of the Cenozoic. Despite the vast paleoceanographic potential of constant flux proxies, few studies have directly compared the behavior of 230ThXS and 3HeET using measurements from the same samples. Sediment grain size fractionation and local scavenging effects may differentially bias one or both proxy systems and complicate the interpretation of 230ThXS or 3HeET data. We will present a new record of vertical sediment accumulation rates spanning the past 600 ka in the Northeast Pacific constrained using analyses of both 3HeET and 230ThXS in two sediment cores from cruise AT26-19 on the Juan de Fuca Ridge. Such a record allows for intercomparison of both constant flux proxies in the mid-ocean ridge environment and examination of sedimentary behavior across multiple glacial cycles. The 230ThXS-derived accumulation rates typically range from 0.5 to 2 g cm-2 ka-1 over the past 450 ka, with periods of maximum deposition coinciding with glacial maxima. Preliminary results of samples analyzed with both 3HeET and 230ThXS indicate relative consistency between vertical sediment accumulation rates computed from each proxy and encourage the use of these constant flux proxies in other sedimentary records.

Hydrologic Connectivity and Land Use Effects on Sediment Accumulation on Stream Floodplains of the Savannah River Site, South Carolina.

NASA Astrophysics Data System (ADS)

Eddy, J.; Yeager, K. M.; Barton, C.; Phillips, J. D.

2016-12-01

Natural sediment accumulation on floodplains is important to maintain water quality of streams, to support regional biodiversity as an ecotone between aquatic and terrestrial environments, and to serve as a sink for organic and inorganic carbon. Recent research suggests that land use and hydrologic connectivity play important roles in determining rates of sediment accumulation. This study hypothesizes that changes in hydrologic connectivity have a greater impact on sediment accumulation rates than changes in land use. Nine sediment cores from seven sub-basins were taken from the Savannah River Site, South Carolina, and processed for grain-size, radioisotope dating, particulate organic carbon (POC), and microscopy. Stratigraphic columns were created for all nine cores. Extensive historical records, aerial, and satellite imagery are used to identify anthropogenic disturbances which may have influenced rates of sediment accumulation, as well as to calculate the percentage of natural vegetation in 1951 and 2014. Grain-size analysis and microscopy indicate that the majority of sediment studied is sand-sized quartz; changes in grain-size classification is used to indicate potential differences in sediment sources. LiDAR and field survey data were used to identify 251 stream flow impediments that potentially affect hydrologic connectivity. Results from radioisotope dating and POC have been used to calculate sediment mass accumulation rates (SMAR; g cm-2 y-1) and linear accumulation rates (LAR; cm y-1) for each of the cores. Preliminary findings show that plots of SMAR versus the number of flow impediments have steeper slopes than plots of SMAR versus the percent difference in vegetation (from 1951 to 2014). This signifies that flow impediments, as a proxy for hydrologic connectivity, have a stronger effect on sediment accumulation rates than changes in land use. This knowledge can help future stream restoration efforts by focusing resources to more efficiently attain stated goals.

Contemporary suspended sediment fluxes and accumulation processes in the small proglacial Sætrevatnet sub-catchment, Bødalen, Western Norway

NASA Astrophysics Data System (ADS)

Liermann, S.; Beylich, A. A.

2012-04-01

A combination of different process monitoring, lake sediment coring and sediment analysis methods and techniques were applied in order (i) to ascertain the hydro-meteorological controls of runoff generation, suspended sediment transport and sediment accumulation on the delta and in Lake Sætrevatnet and (ii) to define the role of the small proglacial lake Sætrevatnet within the basin-wide catchment routing system of the Bødalen valley-fjord system (Nordfjord area, western Norway). Within the Bødalen valley investigations of sediment transfer and sediment accumulation processes were focused on the small proglacial Sætrevatnet area in upper Bødalen. The proglacial Sætrevatnet valley segment shows the characteristic seasonal weather-depended runoff variation for glacierized drainage basins. Suspended sediment concentration varied closely related to water discharge. Hence, significant suspended sediment transport is associated to high runoff conditions during thermally induced summer glacier melt (when 61.9% of the annual suspended sediment yield was recorded in 2010) as well as to single extreme rainfall events (19.8% of the annual suspended sediment yield was recorded during a single extreme rainfall event in 2010). Solar radiation and the magnitude and frequency of extreme rainfall events were found to be crucial for the rate of sediment transport within the Sætrevatnet sub-catchment. Altogether, the annual suspended sediment yield is with 24.2 t km-2 notable lower as compared to other glacierized basins worldwide. Delta accumulation rates at the inlet of Lake Sætrevatnet of 4 cm yr-1 in 2009 and 3.5 cm yr-1 in 2010 as well as a mean annual delta advance of about 3 - 4 m as calculated from comparisons of aerial photographs point to an ongoing and rapid sediment infill of the Sætrevatnet valley basin. Lacustrine sediment sequence analysis and 210-Pb and 137-Cs dating of samples taken from the Lake Sætrevatnet confirm high annual accumulation rates. Based on a basic CSR model (with the assumption of a constant rate of 210-Pb supply) and additionally validated by 137-Cs activity an annual lake sedimentation rate of 1.7cm was calculated. Both the low suspended sediment yields and the high accumulation rates emphasize the importance of bedload and nearly to the channel beds transported sediments for the Sætrevatnet lake system. As a result, Lake Sætrevatnet currently traps about 80-85 % of the sediments delivered from the upstream located glacial and proglacial system highlighting the importance of small ephemeral lakes within larger valley-fjord sediment routing systems. As a next step the potential yearly pattern of laminations (varves) is discussed in association with the calculated sedimentation rates within the Sætrevatnet valley segment. ITRAX (XRF) analysis, magnetic susceptibility measurements and the interpretation of the potential varve/lamination thickness and composition enable the identification of different sedimentary processes and related discharge mechanisms within the Saetrevatnet sub-catchment. Rhythmites are tentatively associated to regional meteorological variables (temperature; precipitation, e.g. heavy rainfall events). Analysis of grain size composition, density and carbon (TOC, inorganic carbon using LECO) are carried out to characterize the laminated structure and to identify possible sediment sources.

A two-dimensional, time-dependent model of suspended sediment transport and bed reworking for continental shelves

USGS Publications Warehouse

Harris, C.K.; Wiberg, P.L.

2001-01-01

A two-dimensional, time-dependent solution to the transport equation is formulated to account for advection and diffusion of sediment suspended in the bottom boundary layer of continental shelves. This model utilizes a semi-implicit, upwind-differencing scheme to solve the advection-diffusion equation across a two-dimensional transect that is configured so that one dimension is the vertical, and the other is a horizontal dimension usually aligned perpendicular to shelf bathymetry. The model calculates suspended sediment concentration and flux; and requires as input wave properties, current velocities, sediment size distributions, and hydrodynamic sediment properties. From the calculated two-dimensional suspended sediment fluxes, we quantify the redistribution of shelf sediment, bed erosion, and deposition for several sediment sizes during resuspension events. The two-dimensional, time-dependent approach directly accounts for cross-shelf gradients in bed shear stress and sediment properties, as well as transport that occurs before steady-state suspended sediment concentrations have been attained. By including the vertical dimension in the calculations, we avoid depth-averaging suspended sediment concentrations and fluxes, and directly account for differences in transport rates and directions for fine and coarse sediment in the bottom boundary layer. A flux condition is used as the bottom boundary condition for the transport equation in order to capture time-dependence of the suspended sediment field. Model calculations demonstrate the significance of both time-dependent and spatial terms on transport and depositional patterns on continental shelves. ?? 2001 Elsevier Science Ltd. All rights reserved.

A model for assessing water quality risk in catchments prone to wildfire

NASA Astrophysics Data System (ADS)

Langhans, Christoph; Smith, Hugh; Chong, Derek; Nyman, Petter; Lane, Patrick; Sheridan, Gary

2017-04-01

Post-fire debris flows can have erosion rates up to three orders of magnitude higher than background rates. They are major sources of fine suspended sediment, which is critical to the safety of water supply from forested catchments. Fire can cover parts or all of these large catchments and burn severity is often heterogeneous. The probability of spatial and temporal overlap of fire disturbance and rainfall events, and the susceptibility of hillslopes to severe erosion determine the risk to water quality. Here we present a model to calculate recurrence intervals of high magnitude sediment delivery from runoff-generated debris flows to a reservoir in a large catchment (>100 km2) accounting for heterogeneous burn conditions. Debris flow initiation was modelled with indicators of surface runoff and soil surface erodibility. Debris flow volume was calculated with an empirical model, and fine sediment delivery was calculated using simple, expert-based assumptions. In a Monte-Carlo simulation, wildfire was modelled with a fire spread model using historic data on weather and ignition probabilities for a forested catchment in central Victoria, Australia. Multiple high intensity storms covering the study catchment were simulated using Intensity-Frequency-Duration relationships, and the runoff indicator calculated with a runoff model for hillslopes. A sensitivity analysis showed that fine sediment is most sensitive to variables related to the texture of the source material, debris flow volume estimation, and the proportion of fine sediment transported to the reservoir. As a measure of indirect validation, denudation rates of 4.6 - 28.5 mm ka-1 were estimated and compared well to other studies in the region. From the results it was extrapolated that in the absence of fire management intervention the critical sediment concentrations in the studied reservoir could be exceeded in intervals of 18 - 124 years.

Global Distribution of Net Electron Acceptance in Subseafloor Sediment

NASA Astrophysics Data System (ADS)

Fulfer, V. M.; Pockalny, R. A.; D'Hondt, S.

2017-12-01

We quantified the global distribution of net electron acceptance rates (e-/m2/year) in subseafloor sediment (>1.5 meters below seafloor [mbsf]) using (i) a modified version of the chemical-reaction-rate algorithm by Wang et al. (2008), (ii) physical properties and dissolved oxygen and sulfate data from interstitial waters of sediment cores collected by the Ocean Drilling Program, Integrated Ocean Drilling Program, International Ocean Discovery Program, and U.S. coring expeditions, and (iii) correlation of net electron acceptance rates to global oceanographic properties. Calculated net rates vary from 4.8 x 1019 e-/m2/year for slowly accumulating abyssal clay to 1.2 x 1023 e-/m2/year for regions of high sedimentation rate. Net electron acceptance rate correlates strongly with mean sedimentation rate. Where sedimentation rate is very low (e.g., 1 m/Myr), dissolved oxygen penetrates more than 70 mbsf and is the primary terminal electron acceptor. Where sedimentation rate is moderate (e.g., 3 to 60 m/Myr), dissolved sulfate penetrates as far as 700 mbsf and is the principal terminal electron acceptor. Where sedimentation rate is high (e.g., > 60 m/Myr), dissolved sulfate penetrates only meters, but is the principal terminal electron acceptor in subseafloor sediment to the depth of sulfate penetration. Because microbial metabolism continues at greater depths than the depth of sulfate penetration in fast-accumulating sediment, complete quantification of subseafloor metabolic rates will require consideration of other chemical species.

Denitrification and Nitrogen Fixation in Alaskan Continental Shelf Sediments

PubMed Central

Haines, John R.; Atlas, Ronald M.; Griffiths, Robert P.; Morita, Richard Y.

1981-01-01

Rates of nitrogen fixation and denitrification were measured in Alaskan continental shelf sediments. In some regions, rates of nitrogen fixation and denitrification appeared to be equal; in other areas, rates were significantly different. Potential rates of denitrification were found to be limited primarily by the available nitrate substrate. Major regional differences in rates of denitrification were not statistically significant, but significant differences were found for nitrogen fixation rates in different regions of the Alaskan continental shelf. Estimated net losses of nitrogen from Bering Sea sediments were calculated as 1.8 × 1012 g of N/yr. Experimental exposure of continental shelf sediments to petroleum hydrocarbons reduced rates of nitrogen fixation and denitrification in some cases but not others. Long-term exposure was necessary before a reduction in nitrogen fixation rates was observed; unamended rates of denitrification but not potential denitrification rates (NO3− added) were depressed after exposure to hydrocarbons. PMID:16345716

Estimation of suspended-sediment rating curves and mean suspended-sediment loads

USGS Publications Warehouse

Crawford, Charles G.

1991-01-01

A simulation study was done to evaluate: (1) the accuracy and precision of parameter estimates for the bias-corrected, transformed-linear and non-linear models obtained by the method of least squares; (2) the accuracy of mean suspended-sediment loads calculated by the flow-duration, rating-curve method using model parameters obtained by the alternative methods. Parameter estimates obtained by least squares for the bias-corrected, transformed-linear model were considerably more precise than those obtained for the non-linear or weighted non-linear model. The accuracy of parameter estimates obtained for the biascorrected, transformed-linear and weighted non-linear model was similar and was much greater than the accuracy obtained by non-linear least squares. The improved parameter estimates obtained by the biascorrected, transformed-linear or weighted non-linear model yield estimates of mean suspended-sediment load calculated by the flow-duration, rating-curve method that are more accurate and precise than those obtained for the non-linear model.

Observations of Lower Mississippi River Estuarine Dynamics: Effects of the Salt Wedge on Sediment Deposition

NASA Astrophysics Data System (ADS)

Ramirez, M. T.; Allison, M. A.

2017-12-01

The lowermost Mississippi River is subject to salt-wedge estuarine conditions during seasonally low flow, when seaward flow is unable to overcome density stratification. Previous studies in the Mississippi River salt wedge have shown the deposition of a fine sediment layer accumulating several mm/day beneath the reach where the salt wedge is present. Field studies were conducted during low flow in 2012-2015 utilizing ADCP, CTD, LISST, and physical samples to observe the physics of the salt wedge reach and to calculate rates and character of sediment trapping beneath the salt wedge. The field observations were summarized using a two-layer box-model representation of the reach to calculate water and sediment budgets entering, exiting, and stored within the reach. The salt wedge reach was found to be net depositional at rates up to 1.8 mm/day. The mechanism for transferring sediment mass from the downstream-flowing fluvial layer to the upstream-flowing marine layer appears to be flocculation, evidenced in LISST data by a spike in sediment particle diameters at the halocline. Applying reach-averaged rates of sediment trapping to a time-integrated model of salt-wedge position, we calculated annual totals ranging from 0.025 to 2.2 million tons of sediment deposited beneath the salt wedge, depending on salt-wedge persistence and upstream extent. Most years this seasonal deposit is remobilized during spring flood following the low-flow estuarine season, which may affect the timing of sediment delivery to the Gulf of Mexico, as well as particulate organic carbon, whose transport trajectory mirrors that of mineral sediment. These results are also relevant to ongoing dredging efforts necessary to maintain the economically-important navigation pathway through the lower Mississippi River, as well as planned efforts to use Mississippi River sedimentary resources to build land in the degrading Louisiana deltaic coast.

Sediment Budgeting in Dam-Affected Rivers: Assessing the Influence of Damming, Tributaries, and Alluvial Valley Sediment Storage on Sediment Regimes

NASA Astrophysics Data System (ADS)

Wilcox, A. C.; Dekker, F. J.; Riebe, C. S.

2014-12-01

Although sediment supply is recognized as a fundamental driver of fluvial processes, measuring how dams affect sediment regimes and incorporating such knowledge into management strategies remains challenging. To determine the influences of damming, tributary supply, and valley morphology and sediment storage on downstream sediment supply in a dryland river, the Bill Williams River (BWR) in western Arizona, we measured basin erosion rates using cosmogenic nuclide analysis of beryllium-10 (10Be) at sites upstream and downstream of a dam along the BWR, as well as from tributaries downstream of the dam. Riverbed sediment mixing calculations were used to test if the dam, which blocks sediment supply from the upper 85% of the basin's drainage area, increases the proportion of tributary sediment to residual upstream sediment in mainstem samples downstream of the dam. Erosion rates in the BWR watershed are more than twice as large in the upper catchment (136 t km-2 yr-1) than in tributaries downstream of Alamo Dam (61 t km-2 yr-1). Tributaries downstream of the dam have little influence on mainstem sediment dynamics. The effect of the dam on reducing sediment supply is limited, however, because of the presence of large alluvial valleys along the mainstem BWR downstream of the dam that store substantial sediment and mitigate supply reductions from the upper watershed. These inferences, from our 10Be derived erosion rates and mixing calculations, are consistent with field observations of downstream changes in bed material size, which suggest that sediment-deficit conditions are restricted to a 10 km reach downstream of the dam, and limited reservoir bathymetry data. Many studies have suggested that tributary sediment inputs downstream of dams play a key role in mitigating dam-induced sediment deficits, but here we show that in a dryland river with ephemeral tributaries, sediment stored in alluvial valleys can also play a key role and in some cases trumps the role of tributaries.

Feedbacks of sedimentation on crustal heat flow - New insights from the Vøring Basin, Norwegian Sea

NASA Astrophysics Data System (ADS)

Theissen, S.; Ruepke, L. H.

2009-04-01

Information on the nature and origin of rift basins is preserved in the presently observed stratigraphy. Basin modeling aims at recovering this information with the goal of quantifying a basin's structural and thermal evolution. Decompaction and backstripping analysis is a classic and still popular approach to basin reconstruction [Steckler and Watts, 1978]. The total and tectonic subsidences, as well as sedimentation rates are calculated by the consecutive decompaction and removal of individual layers. The thermal history has to be computed separately using forward thermal models. An alternative is coupled forward modeling, where the structural and thermal history is computed simultaneously. A key difference between these reconstruction methods is that feedbacks of sedimentation on crustal heat flow are often neglected in backstripping methods. In this work we use the coupled basin modeling approach presented by Rüpke et al. [2008] to quantify some of the feedbacks between sedimentation and heat flow and to explore the differences between both reconstruction approaches in a case study from the Vøring Basin, Norwegian Sea. In a series of synthetic model runs we have reviewed the effects of sedimentation on basement heat flow. These example calculations clearly confirm the well-known blanketing effect of sedimentation and show that it is largest for high sedimentation rates. Recovery of sedimentation rates from the stratigraphy is, however, not straightforward. Decompaction-based methods may systematically underestimate sedimentation rates as sediment thickness is assumed to not change/thin during stretching. We present a new method for computing sedimentation rates based on forward modeling and demonstrate the differences between both methods in terms of rates and thermal feedbacks in a reconstruction of the Vøring basin (Euromargin transect 2). We find that sedimentation rates are systematically higher in forward models and heat flow is clearly depressed during times of high sedimentation. In addition, computed subsidence curves can differ significantly between backtripping and forward modeling methods. This shows that integrated basin modeling is important for improved reconstructions of sedimentary basins and passive margins. Rupke, L. H., et al. (2008), Automated thermotectonostratigraphic basin reconstruction: Viking Graben case study, AAPG Bulletin, 92(3), 309-326. Steckler, M. S., and A. B. Watts (1978), SUBSIDENCE OF ATLANTIC-TYPE CONTINENTAL-MARGIN OFF NEW-YORK, Earth and Planetary Science Letters, 41(1), 1-13.

Microbial cycling of mercury in contaminated pelagic and wetland sediments of San Pablo Bay, California

USGS Publications Warehouse

Marvin-DiPasquale, M. C.; Agee, J.L.; Bouse, R.M.; Jaffe, B.E.

2003-01-01

San Pablo Bay is an estuary, within northern San Francisco Bay, containing elevated sediment mercury (Hg) levels because of historic loading of hydraulic mining debris during the California gold-rush of the late 1800s. A preliminary investigation of benthic microbial Hg cycling was conducted in surface sediment (0-4 cm) collected from one salt-marsh and three open-water sites. A deeper profile (0-26 cm) was evaluated at one of the open-water locations. Radiolabeled model Hg-compounds were used to measure rates of both methylmercury (MeHg) production and degradation by bacteria. While all sites and depths had similar total-Hg concentrations (0.3-0.6 ppm), and geochemical signatures of mining debris (as eNd, range: -3.08 to -4.37), in-situ MeHg was highest in the marsh (5.4??3.5 ppb) and ??? 0.7 ppb in all open-water sites. Microbial MeHg production (potential rate) in 0-4 surface sediments was also highest in the marsh (3.1 ng g-1 wet sediment day-1) and below detection (<0.06 ng g-1 wet sediment day-1) in open-water locations. The marsh exhibited a methylation/demethylation (M/D) ratio more than 25x that of all open-water locations. Only below the surface 0-4-cm horizon was significant MeHg production potential evident in the open-water sediment profile (0.2-1.1 ng g-1 wet sediment day-1). In-situ Hg methylation rates, calculated from radiotracer rate constants, and in-situ inorganic Hg(II) concentrations compared well with potential rates. However, similarly calculated in-situ rates of MeHg degradation were much lower than potential rates. These preliminary data indicate that wetlands surrounding San Pablo Bay represent important zones of MeHg production, more so than similarly Hg-contaminated adjacent open-water areas. This has significant implications for this and other Hg-impacted systems, where wetland expansion is currently planned.

River Sediment Monitoring Using Remote Sensing and GIS (case Study Karaj Watershed)

NASA Astrophysics Data System (ADS)

Shafaie, M.; Ghodosi, H.; Mostofi, K. H.

2015-12-01

Whereas the tank volume and dehydrating digits from kinds of tanks are depended on repository sludge, so calculating the sediments is so important in tank planning and hydraulic structures. We are worry a lot about soil erosion in the basin area leading to deposit in rivers and lakes. It holds two reasons: firstly, because the surface soil of drainage would lose its fertility and secondly, the capacity of the tank decreases also it causes the decrease of water quality in downstream. Several studies have shown that we can estimate the rate of suspension sediments through remote sensing techniques. Whereas using remote sensing methods in contrast to the traditional and current techniques is faster and more accurate then they can be used as the effective techniques. The intent of this study has already been to estimate the rate of sediments in Karaj watershed through remote sensing and satellite images then comparing the gained results to the sediments data to use them in gauge-hydraulic station. We mean to recognize the remote sensing methods in calculating sediment and use them to determine the rate of river sediments so that identifying their accuracies. According to the results gained of the shown relations at this article, the amount of annual suspended sedimentary in KARAJ watershed have been 320490 Tones and in hydrologic method is about 350764 Tones .

The response of excess 230Th and extraterrestrial 3He to sediment redistribution at the Blake Ridge, western North Atlantic

NASA Astrophysics Data System (ADS)

McGee, David; Marcantonio, Franco; McManus, Jerry F.; Winckler, Gisela

2010-10-01

The constant-flux proxies excess 230Th ( 230Th xs) and extraterrestrial 3He ( 3He ET) are commonly used to calculate sedimentary mass accumulation rates and to quantify lateral advection of sediment at core sites. In settings with significant lateral input or removal of sediment, these calculations depend on the assumption that concentrations of 230Th xs and 3He ET are the same in both advected sediment and sediment falling through the water column above the core site. Sediment redistribution is known to fractionate grain sizes, preferentially transporting fine grains; though relatively few studies have examined the grain size distribution of 230Th xs and 3He ET, presently available data indicate that both are concentrated in fine grains, suggesting that fractionation during advection may bias accumulation rate and lateral advection estimates based on these proxies. In this study, we evaluate the behavior of 230Th xs and 3He ET in Holocene and last glacial samples from two cores from the Blake Ridge, a drift deposit in the western North Atlantic. At the end of the last glacial period, both cores received large amounts of laterally transported sediment enriched in fine-grained material. We find that accumulation rates calculated by normalization to 230Th and 3He are internally consistent despite large spatial and temporal differences in sediment advection. Our analyses of grain size fractions indicate that ~ 70% of 3He ET-bearing grains are in the < 20 μm fraction, with roughly equal amounts in the < 4 and 4-20 μm fractions. 230Th xs is concentrated in <4-μm grains relative to 4- to 20-μm grains by approximately a factor of 2 in Holocene samples and by a much larger factor (averaging a factor of 10) in glacial samples. Despite these enrichments of both constant-flux proxies in fine particles, the fidelity of 230Th- and 3He-based accumulation rate estimates appears to be preserved even in settings with extreme sediment redistribution, perhaps due to the cohesive behavior of fine particles in marine settings.

The contribution of ice cover to sediment resuspension in a shallow temperate lake: possible effects of climate change on internal nutrient loading.

PubMed

Niemistö, Juha P; Horppila, Jukka

2007-01-01

The effect of ice cover on sediment resuspension and internal total P (Tot-P) loading was studied in the northern temperate Kirkkojärvi basin in Finland. The gross sedimentation and resuspension rates were estimated with sediment traps during ice-cover and ice-free periods. After ice break, the average gross sedimentation rate increased from 1.4 to 30.0 g dw m(-2) d(-1). Resuspension calculations showed clearly higher values after ice break as well. Under ice cover, resuspension ranged from 50 to 78% of the gross sedimentation while during the ice-free period it constituted from 87 to 97% of the gross sedimentation. Consequently, the average resuspension rate increased from 1.0 g dw m(-2) d(-1) under ice-cover to 27.0 g dw m(-2) d(-1) after thaw, indicating the strong effect of ice cover on sediment resuspension. To estimate the potential effect of climate change on internal P loading caused by resuspension we compared the Tot-P loading calculations between the present climate and the climate with doubled atmospheric CO2 concentration relative to the present day values (ice cover reduced from current 165 to 105 d). The annual load increased from 7.4 to 9.4 g m(-2). In conclusion, the annual internal Tot-P loading caused by resuspension will increase by 28% in the Kirkkojärvi basin if the 2xCO2 climate scenario comes true.

Online interactive U.S. Reservoir Sedimentation Survey Database

USGS Publications Warehouse

Gray, J.B.; Bernard, J.M.; Schwarz, G.E.; Stewart, D.W.; Ray, K.T.

2009-01-01

In April 2009, the U.S. Geological Survey and the Natural Resources Conservation Service (prior to 1994, the Soil Conservation Service) created the Reservoir Sedimentation Survey Database (RESSED) and Web site, the most comprehensive compilation of data from reservoir bathymetric and dry basin surveys in the United States. RESSED data can be useful for a number of purposes, including calculating changes in reservoir storage characteristics, quantifying rates of sediment delivery to reservoirs, and estimating erosion rates in a reservoir's watershed.

A 10Be-based sediment budget of the Upper Rhône basin, Central Swiss Alps

NASA Astrophysics Data System (ADS)

Stutenbecker, Laura; Delunel, Romain; Schlunegger, Fritz; Akçar, Naki; Christl, Marcus

2017-04-01

The Upper Rhône catchment located in southwestern Switzerland is one of the largest Alpine intramontane basins and, due to high topographic gradients and intense glacial conditioning, an important sediment factory in the Alps. Sediment is being produced in around 50 tributary basins, transported along the 150 km long course of the Rhône River, and deposited in the river delta and associated subaquatic canyons within Lake Geneva, its primary sedimentary sink. In order to quantify the modern sediment fluxes in this Alpine basin we infer catchment-wide denudation rates from concentrations of the cosmogenic nuclide 10Be in quartz extracted from modern fluvial sediment of the major tributary basins. Additionally, 10Be-based denudation rates are calculated for 14 locations along the main Rhône River to track downstream changes. Results from the tributary basins show a large scatter of 10Be concentrations and their respective inferred denudation rates, ranging from 9.72 x 104 atoms/g and 0.17 mm/a to 0.13 x 104 atoms/g and 2.64 mm/a. The Rhône basin does show a rather large spatial variability of parameters that are known to possibly influence denudation rates, for example recent rock uplift rates, lithology, precipitation and temperature, as well as geomorphological parameters such as relief, mean elevation and slope values. However, there is no significant correlation between those parameters and the calculated denudation rates. Instead, the denudation rates are found to be positively correlated with the recent glacial cover in the catchments. This suggests that in glaciated basins glaciogenic material with very low 10Be concentrations is the dominating source of sediment, and inferred denudation rates must be interpreted with great care, as they may overestimate the actual rates. Downstream the main Rhône River the 10Be-concentrations are rather stable and do not record significant inputs of the glaciogenic material supplied by the glaciated basins. Possible explanations we would like to discuss here include differences in sediment connectivity and temporary sediment storage.

Dilution of 10Be in detrital quartz by earthquake-induced landslides: Implications for determining denudation rates and potential to provide insights into landslide sediment dynamics

NASA Astrophysics Data System (ADS)

West, A. Joshua; Hetzel, Ralf; Li, Gen; Jin, Zhangdong; Zhang, Fei; Hilton, Robert G.; Densmore, Alexander L.

2014-06-01

The concentration of 10Be in detrital quartz (10Beqtz) from river sediments is now widely used to quantify catchment-wide denudation rates but may also be sensitive to inputs from bedrock landslides that deliver sediment with low 10Beqtz. Major landslide-triggering events can provide large amounts of low-concentration material to rivers in mountain catchments, but changes in river sediment 10Beqtz due to such events have not yet been measured directly. Here we examine the impact of widespread landslides triggered by the 2008 Wenchuan earthquake on 10Beqtz in sediment samples from the Min Jiang river basin, in Sichuan, China. Landslide deposit material associated with the Wenchuan earthquake has consistently lower 10Beqtz than in river sediment prior to the earthquake. River sediment 10Beqtz decreased significantly following the earthquake downstream of areas of high coseismic landslide occurrence (i.e., with greater than ∼0.3% of the upstream catchment area affected by landslides), because of input of the 10Be-depleted landslide material, but showed no systematic changes where landslide occurrence was low. Changes in river sediment 10Beqtz concentration were largest in small first-order catchments but were still significant in large river basins with areas of 104-105 km. Spatial and temporal variability in river sediment 10Beqtz has important implications for inferring representative denudation rates in tectonically active, landslide-dominated environments, even in large basins. Although the dilution of 10Beqtz in river sediment by landslide inputs may complicate interpretation of denudation rates, it also may provide a possible opportunity to track the transport of landslide sediment. The associated uncertainties are large, but in the Wenchuan case, calculations based on 10Be mixing proportions suggest that river sediment fluxes in the 2-3 years following the earthquake increased by a similar order of magnitude in the 0.25-1 mm and the <0.25 mm size fractions, as determined from 10Beqtz mixing calculations and hydrological gauging, respectively. Such information could provide new insight into sediment transfer, with implications for secondary sediment-related hazards and for understanding the removal of mass from mountains.

Recent changes in Red Lake (Romania) sedimentation rate determined from depth profiles of 210Pb and 137Cs radioisotopes.

PubMed

Begy, R; Cosma, C; Timar, A

2009-08-01

This work presents a first estimation of the sedimentation rate for the Red Lake (Romania). The sediment accumulation rates were determined by two well-known methods for recent sediment dating: (210)Pb and (137)Cs methods. Both techniques implied used the gamma emission of the above-mentioned radionuclides. The (210)Pb and (137)Cs concentrations in the sediment were measured using a gamma spectrometer with a HpGe detector, Gamma-X type. Activities ranging from 41+/-7 to 135+/-34Bq/kg were found for (210)Pb and from 3+/-0.5 to 1054+/-150Bq/kg for (137)Cs. The sediment profile indicates acceleration in sedimentation rate in the last 18 years. Thus, the sedimentation process for the Red Lake can be divided in two periods, the last 18 years, and respectively, the period before that. Using the Constant Rate of (210)Pb Supply method values between 0.18+/-0.04 and 1.85+/-0.5g/cm(2) year (0.32+/-0.08 and 2.83+/-0.7cm/year) were obtained. Considering both periods, an average sedimentation rate of 0.87+/-0.17g/cm(2) year (1.17cm/year) was calculated. Considering an average depth of 5.41m for the lake and the sedimentation rate estimated for the last 18 years, it could be estimated that the lake will disappear in 195 years.

Quantitative geochemical modeling along a transect off Peru: Carbon cycling in time and space, and the triggering factors for carbon loss and storage

NASA Astrophysics Data System (ADS)

Arning, Esther T.; van Berk, Wolfgang; Schulz, Hans-Martin

2012-12-01

Early diagenetic processes in Peruvian shelf and slope sediments are numerically reproduced by applying chemical thermodynamics in a complex, universal approach using the PHREEQC (version 2) computer code. The reaction kinetics of organic carbon remineralization are integrated into a set of equilibrium reactions by defining the type and the amount of converted organic matter in a certain time step. We calculate the most intense remineralization of organic carbon for present-day shelf sites, and the final carbon pool is dominated by secondary carbonates. This serves to highlight the influence of organic matter degradation and anaerobic oxidation of methane (AOM) on diagenetic mineral formation. The enrichment of aqueous methane and the formation of methane hydrate only takes place in slope sediments with high sedimentation rates that prevent diffusive loss of methane (e.g., Sites 682 and 688). Moreover, AOM prevents the diffusion of dissolved methane into overlying seawater. Throughout the Miocene period, these sites were located on a former shelf and the total carbon loss from the sediments was significantly higher in comparison with the present-day. Compared with the present-day shelf site, organic matter remineralization is high, and methane is produced but not stored within the sediments. Our model calculations rule out the possibility of present-day and former shelf site sediments off the coast of Peru as methane reservoirs. Remineralized TOC has to be considered, particularly in older sediments, when interpreting TOC profiles and calculating mass accumulation rates of total organic carbon (MARTOC). The more organic matter has been remineralized during the depositional history, the larger the difference between MARTOC calculated from measured TOC data, and from the sum of modeled and measured TOC data. Consequently, most reliable primary productivity calculations are based on the sum of measured relict TOC and the amount of remineralized organic carbon determined by modeling.

Factors controlling denitrification rates of tidal mudflats and fringing salt marshes in south-west England

NASA Astrophysics Data System (ADS)

Koch, M. S.; Maltby, E.; Oliver, G. A.; Bakker, S. A.

1992-05-01

Denitrification rates were determined utilizing the acetylene blockage technique at three sites: upper mudflat, lower mudflat, and Halimione portulacoides marsh on the fringing wetlands of the Torridge River Estuary in South-west England. Denitrification rates were calculated from nitrous oxide (N 2O) production each month for 1 year with intact sediment cores extracted at low tide (0-5 cm). In the lower and upper mudflat sites denitrification rates were low ranging from 0·52 to 5·78 μmol and 1·28 to 4·36 μmol N 2 m -2 h -1, respectively. Denitrification rates in marsh sediments were consistently higher than those of the mudflat ranging from 2·51 to 59·00 μmol N 2 m -2 h -1. Amending river water to sediment cores stimulated lower and upper mudflat denitrification rates approximately 10-fold up to 106·39 and 96·73 μmol N 2 m -2 h -1, respectively. In marsh sediments, a two-fold increase in denitrification was found with river water amended resulting in a maximum rate of 114·80 μmol N 2 m -2 h -1. During the winter months, when riverine NO 3-N levels were at a maximum (2·47 to 2·93 mg l -1), denitrification rates were highest (75·24 to 114·99 μmol N 2 m -2 h -1) and conversely, during the summer both NO 3-N concentrations (1·0 to 1·70 mg l -1) and denitrification (0·95 to 37·38 μmol N 2 m -2 h -1) rates were at a minimum. Mudflat sediment redox potentials (Eh), within the theoretical range of NO 3-1 instability, were limited to the upper 5 mm, thus maximum denitrification rates may be restricted to the sediment surface. When calculating annual denitrification rates in tidal estuaries several factors should be considered including: seasonal NO 3-1 concentrations in tidal water, tidal flooding duration and amplitude, and the depth of the aerobic/anaerobic zone of the sediment.

Sediment accumulation rates and high-resolution stratigraphy of recent fluvial suspension deposits in various fluvial settings, Morava River catchment area, Czech Republic

NASA Astrophysics Data System (ADS)

Sedláček, Jan; Bábek, Ondřej; Kielar, Ondřej

2016-02-01

We present a comprehensive study concerning sedimentary processes in fluvial sediment traps within the Morava River catchment area (Czech Republic) involving three dammed reservoirs, four meanders and oxbow lakes, and several natural floodplain sites. The objective of the study was to determine sediment accumulation rates (SAR), estimate erosion rates, calculating these using a combination of the 137Cs method and historical data. Another purpose of this study was to provide insight into changing erosion and accumulation rates over the last century. Extensive water course modifications were carried out in the Morava River catchment area during the twentieth century, which likely affected sedimentation rates along the river course. Other multiproxy stratigraphic methods (X-ray densitometry, magnetic susceptibility, and visible-light reflectance spectrometry) were applied to obtain additional information about sediment infill. Sediment stratigraphy revealed distinct distal-to-proximal patterns, especially in reservoirs. Granulometrically, silts and sandy silts prevailed in sediments. Oxbow lakes and meanders contained larger amounts of clay and organic matter, which is the main difference between them and reservoirs. Pronounced 137Cs peaks were recorded in all studied cores (maximum 377 Bq·kg- 1), thus indicating Chernobyl fallout from 1986 or older events. Calculated sediment accumulation rates were lowest in distal parts of reservoirs (0.13-0.58 cm/y) and floodplains (0.45-0.88 cm/y), moderately high rates were found in proximal parts of reservoirs and oxbow lakes (2.27-4.4 cm/y), and the highest rates in some oxbow lakes located near the river (6-8 cm/y). The frequency of the inundation still can be high in some natural areas as in the Litovelské Pomoraví protected area, whereas the decreasing frequency of the inundation in other modified parts can contribute to a lower sedimentation rate. The local effects such as difference between SARs in oxbow lakes and reservoirs, different grain size distribution in both systems, and high variability in thickness of their proximal and distal parts play a crucial role in the analysis of regional accumulation rates. Local effects are much stronger than regional effects, such as rainfall and land use. Combined with the low resolution of time scales (usually only three datums are available: reservoir construction datum, 137Cs fallout event, and top of sediment), these effects may obscure the general trends of regionally increasing or decreasing net SARs, making the analysis of erosion rates from the sedimentary record an extremely difficult task.

Sediment retention in a bottomland hardwood wetland in Eastern Arkansas

USGS Publications Warehouse

Kleiss, B.A.

1996-01-01

One of the often-stated functions of wetlands is their ability to remove sediments and other particulates from water, thus improving water quality in the adjacent aquatic system. However, actual rates of suspended sediment removal have rarely been measured in freshwater wetland systems. To address this issue, suspended sediment dynamics were measured in a 85-km2 bottomland hardwood (BLH) wetland adjacent to the highly turbid Cache River in eastern Arkansas during the 1988-1990 water years. A suspended sediment mass balance was calculated using depth-integrated, flow-weighted daily measurements at wetland inflow and outflow points. Over the three-year period, suspended sediment load decreased an average of 14% between upstream and downstream sampling points. To test the idea that the suspended sediments were retained by the adjacent wetland and to determine what portion of the BLH forest was most responsible for retaining the suspended sediments, concurrent measurements of sediment accretion were made at 30 sites in the wetland using feldspar clay marker horizons, sedimentation disks, the 137cesium method, and dendrogeomorphic techniques. Sedimentation rates exceeding 1 cm/yr were measured in frequently flooded areas dominated by Nyssa aquatica and Taxodium distichum. Maximum sedimentation rates did not occur on the natural levee, as would be predicted by classical fluvial geomorphology, but in the "first bottom," where retention time of the water reached a maximum. Multiple regression was used to relate sedimentation rates with several physical and biological factors. A combination of distance from the river, flood duration, and tree basal area accounted for nearly 90% of the variation in sedimentation rates.

Approaches to quantifying long-term continental shelf sediment transport with an example from the Northern California STRESS mid-shelf site

NASA Astrophysics Data System (ADS)

Harris, Courtney K.; Wiberg, Patricia L.

1997-09-01

Modeling shelf sediment transport rates and bed reworking depths is problematic when the wave and current forcing conditions are not precisely known, as is usually the case when long-term sedimentation patterns are of interest. Two approaches to modeling sediment transport under such circumstances are considered. The first relies on measured or simulated time series of flow conditions to drive model calculations. The second approach uses as model input probability distribution functions of bottom boundary layer flow conditions developed from wave and current measurements. Sediment transport rates, frequency of bed resuspension by waves and currents, and bed reworking calculated using the two methods are compared at the mid-shelf STRESS (Sediment TRansport on Shelves and Slopes) site on the northern California continental shelf. Current, wave and resuspension measurements at the site are used to generate model inputs and test model results. An 11-year record of bottom wave orbital velocity, calculated from surface wave spectra measured by the National Data Buoy Center (NDBC) Buoy 46013 and verified against bottom tripod measurements, is used to characterize the frequency and duration of wave-driven transport events and to estimate the joint probability distribution of wave orbital velocity and period. A 109-day record of hourly current measurements 10 m above bottom is used to estimate the probability distribution of bottom boundary layer current velocity at this site and to develop an auto-regressive model to simulate current velocities for times when direct measurements of currents are not available. Frequency of transport, the maximum volume of suspended sediment, and average flux calculated using measured wave and simulated current time series agree well with values calculated using measured time series. A probabilistic approach is more amenable to calculations over time scales longer than existing wave records, but it tends to underestimate net transport because it does not capture the episodic nature of transport events. Both methods enable estimates to be made of the uncertainty in transport quantities that arise from an incomplete knowledge of the specific timing of wave and current conditions. 1997 Elsevier Science Ltd

Sedimentation Survey of Lago Guerrero, Puerto Rico, May 2001

USGS Publications Warehouse

Soler-López, Luis R.

2002-01-01

Lago Guerrero, a small reservoir owned by the Puerto Rico Electric Power Authority, is part of the Isabela Hydroelectric System and is located in Aguadilla, in northwestern Puerto Rico. The reservoir had a storage capacity of about 127,376 cubic meters in May 2001 and a maximum depth of about 5.8 meters. Records on dam construction and original topography and storage capacity were not available; therefore, sedimentation rates could not be determined. However, Lago Guerrero resumably was constructed during the 1930?s because it receives water from lago Guajataca, which was constructed in 1928. The May 2001 bathymetric survey of Lago Guerrero established baseline data that are essential to calculate sedimentation rates, sediment yields, storage loss, and sediment deposition sites within the reservoir.

Determination of infiltration and percolation rates along a reach of the Santa Fe River near La Bajada, New Mexico

USGS Publications Warehouse

Thomas, Carole L.; Stewart, Amy E.; Constantz, Jim E.

2000-01-01

Two methods, one a surface-water method and the second a ground-water method, were used to determine infiltration and percolation rates along a 2.5-kilometer reach of the Santa Fe River near La Bajada, New Mexico. The surface-water method uses streamflow measurements and their differences along a stream reach, streamflow-loss rates, stream surface area, and evaporation rates to determine infiltration rates. The ground-water method uses heat as a tracer to monitor percolation through shallow streambed sediments. Data collection began in October 1996 and continued through December 1997. During that period the stream reach was instrumented with three streamflow gages, and temperature profiles were monitored from the stream-sediment interface to about 3 meters below the streambed at four sites along the reach. Infiltration is the downward flow of water through the stream- sediment interface. Infiltration rates ranged from 92 to 267 millimeters per day for an intense measurement period during June 26- 28, 1997, and from 69 to 256 millimeters per day during September 27-October 6, 1997. Investigators calculated infiltration rates from streamflow loss, stream surface-area measurements, and evaporation-rate estimates. Infiltration rates may be affected by unmeasured irrigation-return flow in the study reach. Although the amount of irrigation-return flow was none to very small, it may result in underestimation of infiltration rates. The infiltration portion of streamflow loss was much greater than the evaporation portion. Infiltration accounted for about 92 to 98 percent of streamflow loss. Evaporation-rate estimates ranged from 3.4 to 7.6 millimeters per day based on pan-evaporation data collected at Cochiti Dam, New Mexico, and accounted for about 2 to 8 percent of streamflow loss. Percolation is the movement of water through saturated or unsaturated sediments below the stream-sediment interface. Percolation rates ranged from 40 to 109 millimeters per day during June 26-28, 1997. Percolation rates were not calculated for the September 27-October 6, 1997, period because a late summer flood removed the temperature sensors from the streambed. Investigators used a heat-and-water flow model, VS2DH (variably saturated, two- dimensional heat), to calculate near-surface streambed infiltration and percolation rates from temperatures measured in the stream and streambed. Near the stream-sediment interface, infiltration and percolation rates are comparable. Comparison of infiltration and percolation rates showed that infiltration rates were greater than percolation rates. The method used to calculate infiltration rates accounted for net loss or gain over the entire stream reach, whereas the method used to calculate percolation was dependent on point measurements and, as applied in this study, neglected the nonvertical component of heat and water fluxes. In general, using the ground-water method was less labor intensive than making a series of streamflow measurements and relied on temperature, an easily measured property. The ground-water method also eliminated the difficulty of measuring or estimating evaporation from the water surface and was therefore more direct. Both methods are difficult to use during periods of flood flow. The ground-water method has problems with the thermocouple-wire temperature sensors washing out during flood events. The surface- water method often cannot be used because of safety concerns for personnel making wading streamflow measurements.

Sediment transport on the Palos Verdes shelf over seasonal to decadal time scales

USGS Publications Warehouse

Wiberg, P.L.; Drake, D.E.; Harris, C.K.; Noble, M.

2002-01-01

We combine direct observations, longer-term wave data, and model calculations to characterize resuspension and transport of fine-grained, effluent-affected sediment on the Palos Verdes shelf. Near-bed waves, currents, and suspended sediment concentrations were monitored during the winter of 1992-93 with a bottom tripod and current-meter mooring at a 63-m-deep site. Wave conditions that winter were moderate (??? 2 year recurrence interval), and mean current was alongshelf to the northwest; currents were not significantly correlated with wave conditions. Seven wave events during the winter (December-March) produced near-bed wave orbital velocities at the study site in excess of 14 cm s-1, the observed threshold for significant resuspension. Three of these events occurred during the bottom tripod deployment and are characterized by the highest persistent suspended sediment concentrations in the tripod record. Suspended sediment flux was alongshelf to the northwest for 5 of the 6 wave events for which current data were available; one event occurred during low southeast currents. Measured suspended sediment concentration and grain size generally agree with values that were calculated using a shelf sediment transport model with no adjustment of parameters from values determined for two muddy sites on the northern California shelf. We extend our seasonal observations to a period of almost 2 decades by applying the observed thresholds for wave-driven resuspension to near-bed wave conditions calculated from NDBC Buoy 46025 surface wave data. An average of 10 resuspension events per year, with an average duration of 1.6 days, were identified at a water depth of 60 m; the number of events dropped to 3 per year at 90 m, beyond the shelf break. For the majority of these events, calculated net suspended sediment flux is toward the northwest (alongshelf) at an average rate of 140 kg m-1 h-1; about a third of the events have net southeastward flux at an average rate of 30 kg m-1 h-1. The calculated thickness of the resuspended surface layer of the bed was less than 1 cm for all events at 60 m. ?? 2002 Elsevier Science Ltd. All rights reserved.

Sediment thicknesses and holocene glacial marine sedimentation rates in three east Greenland fjords (ca. 68°N)

USGS Publications Warehouse

Andrews, J.T.; Milliman, John D.; Jennings, A.E.; Rynes, N.; Dwyer, J.

1994-01-01

We compared measured and estimated sediment budgets in heavily glaciated fjords in East Greenland. Mass balance calculations and regional glacio-climatic conditions suggest that the sediment flux to the seafloor in Kangerdlugssuaq and Nansen fjords should be dominated by iceberg rafting and not by the rain-out of suspended particulates in meltwater, as the glacier calving flux is estimated at 15 and $2 km^{3}/yr$, compared to meltwater volumes of 4.4 and $1.7 km^{3}/yr$, respectively. Gravity cores in the three fjords indicate that the uppermost 1-2.5 m of sediment consists of diamictons or fine-grained laminated muds. AMS radiocarbon dates on calcareous foramininfera or shells (16 total) indicate sedimentation rates of 110 to 340 cm/ka within the fjords over the last 1 ka, and 10-20 cm/ka during the Holecene on the inner and middle shelf. Annual sediment discharge is around $0.67 \\times 10^{6}$ tonnes/yr within the Kangerdlugssuaq Fjord and Trough system, which translates into an average basin-wide rate of denudation of 0.01 mm/yr (0.01 m/ka). Air gun and deep-towed (Huntec) seismic profiling was carried out in Kangerdlugssuaq and Nansen fjords, East Greenland, and showed that sediment fills averaged 500 and 350 m respectively; they consist primarily of acoustically stratified sediments. If the sediment fills are entirely Holocene in age then the required average sediment accumulation rates of 35-50 m/ka are an order of magnitude larger than the $^{14}C $controlled rates of the last 1-2 ka. This raises the possibility that fjord sediments may be by-passed and not always recycled during glacial advances; this will affect sedimentation rates on adjacent shelves and deep-sea areas during successive glaciations

Efficacy of 230Th normalization in sediments from the Juan de Fuca Ridge, northeast Pacific Ocean

NASA Astrophysics Data System (ADS)

Costa, Kassandra; McManus, Jerry

2017-01-01

230Th normalization is an indispensable method for reconstructing sedimentation rates and mass fluxes over time, but the validity of this approach has generated considerable debate in the paleoceanographic community. 230Th systematics have been challenged with regards to grain size bias, sediment composition (CaCO3), water column advection, and other processes. In this study, we investigate the consequences of these effects on 230Th normalization from a suite of six cores on the Juan de Fuca Ridge. The proximity of these cores (<30 km) suggests that they should receive the same particle rain rate of sediment, but the steep bathymetry of the ridge leads to substantial sediment redistribution and variable carbonate preservation, both of which may limit the usage of 230Th in this region. Despite anticipated complications, 230Th normalization effectively reconstructs nearly identical particle rain rates from all six cores, which are summarily unrelated to the total sedimentation rates as calculated from the age models. Instead the total sedimentation rates are controlled almost entirely by sediment focusing and winnowing, which are highly variable even over the short spatial scales investigated in this study. Furthermore, no feedbacks on 230Th systematics were detected as a consequence of sediment focusing, coarse fraction variability, or calcium carbonate content, supporting the robustness of the 230Th normalization technique.

Sediment transport and Hg recovery in Lavaca Bay, as evaluated from radionuclide and Hg distributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santschi, P.H.; Allison, M.A.; Asbill, S.

1999-02-01

Mercury was released in the late 1960s from a chloralkali facility managed by ALCOA and deposited into sediments of Lavaca Bay, TX. Sediments have recorded this event as a well-defined subsurface concentration maximum. Radionuclide, mercury, X-radiography, and grain size data from sediment cores taken in 1997 at 15 stations in Lavaca bay were used to assess sediment and Hg movements in the bay. Sediment accumulation rates were calculated from bomb fallout nuclide ({sup 137}Cs, {sup 239,240}Pu) peaks in 1963 and from the steady-state delivery of {sup 210}Pb from the atmosphere. Sedimentation rates are highest at near-shore sites near the ALCOAmore » facility and generally decrease away from shore. Sedimentation rates in some areas are likely influenced by anthropogenic activities such as dredging. Particle reworking, as assessed from {sup 7}Be measurements, is generally restricted to the upper 2--7 cm of sediments. Numerical simulations of Hg profiles using measured sedimentation and mixing parameters indicate that at most sites high remnant mercury concentrations at 15--60 cm depth cannot supply substantial amounts of Hg to surface sediments. Assuming no future Hg supplies, Hg concentrations in surface sediments are predicted to decrease exponentially with a recovery half-time of 4 {+-} 2 years.« less

Effects of hydrologic connectivity and land use on floodplain sediment accumulation at the Savannah River Site, South Carolina.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eddy, Jeremy Edward

Floodplains, and the sediment accumulating naturally on them,are important to maintain stream water quality and serve as sinks for organic and inorganic carbon. Newer theories contend that land use and hydrologic connectivity (water-mediated transport of matter, energy, and/or organisms within or between elements of the hydrologic cycle) play important roles in determining sediment accumulation on floodplains. This study hypothesizes that changes in hydrologic connectivity have a greater impact on floodplain sediment accumulation than changes in land use. Nine sediment cores from seven sub-basins were collected from the Savannah River Site (SRS), South Carolina, and processed for grain-size, radionuclide dating (7Be,more » 137Cs, 210Pb), particulate organic carbon (POC), and microscopy. Historical records, including aerial and satellite imagery,were used to identify anthropogenic disturbances in the sub-basins, as well as to calculate the percentages of natural vegetation land cover at the SRS in 1951, and 2014. LiDAR and field survey data identified 251 flow impediments, measured elevation, and recorded standard stream characteristics (e.g., bank height) that canaffect hydrologic connectivity. Radionuclide dating was used to calculate sediment mass accumulation rates (MARs) and linear accumulation rates (LARs) for each core. Results indicate that sedimentation rates have increased across all SRS sub-basins over the past 40-50 years, shortly after site restoration and recovery efforts began.Findings show that hydrologic connectivity proxies (i.e., stream characteristics and impediments) have stronger relationships to MARs and LARs than the land use proxy (i.e., vegetation cover), confirming the hypothesis. Asstream channel depth and the number of impediments increase,floodplain sedimentation rates also increase. This knowledge can help future stream restoration efforts by focusing resources to more efficiently attain stated goals, particularly in terms of floodplain sediment retention.« less

Use of sediment rating curves and optical backscatter data to characterize sediment transport in the Upper Yuba River watershed, California, 2001-03

USGS Publications Warehouse

Curtis, Jennifer A.; Flint, Lorraine E.; Alpers, Charles N.; Wright, Scott A.; Snyder, Noah P.

2006-01-01

Sediment transport in the upper Yuba River watershed, California, was evaluated from October 2001 through September 2003. This report presents results of a three-year study by the U.S. Geological Survey, in cooperation with the California Ecosystem Restoration Program of the California Bay-Delta Authority and the California Resources Agency. Streamflow and suspended-sediment concentration (SSC) samples were collected at four gaging stations; however, this report focuses on sediment transport at the Middle Yuba River (11410000) and the South Yuba River (11417500) gaging stations. Seasonal suspended-sediment rating curves were developed using a group-average method and non-linear least-squares regression. Bed-load transport relations were used to develop bed-load rating curves, and bed-load measurements were collected to assess the accuracy of these curves. Annual suspended-sediment loads estimated using seasonal SSC rating curves were compared with previously published annual loads estimated using the Graphical Constituent Loading Analysis System (GCLAS). The percent difference ranged from -85 percent to +54 percent and averaged -7.5 percent. During water year 2003 optical backscatter sensors (OBS) were installed to assess event-based suspended-sediment transport. Event-based suspended-sediment loads calculated using seasonal SSC rating curves were compared with loads calculated using calibrated OBS output. The percent difference ranged from +50 percent to -369 percent and averaged -79 percent. The estimated average annual sediment yield at the Middle Yuba River (11410000) gage (5 tons/mi2) was significantly lower than that estimated at the South Yuba River (11417500) gage (14 tons/mi2). In both rivers, bed load represented 1 percent or less of the total annual load throughout the project period. Suspended sediment at the Middle Yuba River (11410000) and South Yuba River (11417500) gages was typically greater than 85 percent silt and clay during water year 2003, and sand concentrations at the South Yuba River (11417500) gage were typically higher than those at the Middle Yuba River (11410000) gage for a given streamflow throughout the three year project period. Factors contributing to differences in sediment loads and grain-size distributions at the Middle Yuba River (11410000) and South Yuba River (11417500) gages include contributing drainage area, flow diversions, and deposition of bed-material-sized sediment in reservoirs upstream of the Middle Yuba River (11410000) gage. Owing to its larger drainage area, higher flows, and absence of man-made structures that restrict sediment movement in the lower basin, the South Yuba River transports a greater and coarser sediment load.

Sedimentation rates and erosion changes recorded in recent sediments of Lake Piaseczno, south-eastern Poland

NASA Astrophysics Data System (ADS)

Tylmann, Wojciech; Turczyński, Marek; Kinder, Małgorzata

2009-10-01

This paper presents the dating results and basic analyses of recent sediments from Lake Piaseczno. The age of sediments was determined using the 210Pb method and constant flux: constant sedimentation (CF: CS) model. The estimated timescale was in agreement with the AMS14C date from the base of the core. The mean sediment accumulation rate during the last 100 years was calculated as 0.025 g cm-2 a-1. Based on the radiocarbon date, the rate of sediment accumulation below the 210Pb dating horizon was estimated as 0.066 g cm-2 a-1. The variability of main physical properties and sediment components along the core was analysed as well. The sediments were characterised by a very high water content (>80%). Carbonates were either not present or at a very low level (<1%). However, organic and minerogenic matter variability represents an interesting record of increasing erosion intensity in the catchment area. Analysis of archival cartographic materials demonstrated that the most likely reason for the enhanced transport of minerogenic matter to the lake was deforestation caused by human activity in the beginning of the 20th century.

Estimation of hydrocarbon biodegradation rates in gasoline-contaminated sediment from measured respiration rates

USGS Publications Warehouse

Baker, R.J.; Baehr, A.L.; Lahvis, M.A.

2000-01-01

An open microcosm method for quantifying microbial respiration and estimating biodegradation rates of hydrocarbons in gasoline-contaminated sediment samples has been developed and validated. Stainless-steel bioreactors are filled with soil or sediment samples, and the vapor-phase composition (concentrations of oxygen (O2), nitrogen (N2), carbon dioxide (CO2), and selected hydrocarbons) is monitored over time. Replacement gas is added as the vapor sample is taken, and selection of the replacement gas composition facilitates real-time decision-making regarding environmental conditions within the bioreactor. This capability allows for maintenance of field conditions over time, which is not possible in closed microcosms. Reaction rates of CO2 and O2 are calculated from the vapor-phase composition time series. Rates of hydrocarbon biodegradation are either measured directly from the hydrocarbon mass balance, or estimated from CO2 and O2 reaction rates and assumed reaction stoichiometries. Open microcosm experiments using sediments spiked with toluene and p-xylene were conducted to validate the stoichiometric assumptions. Respiration rates calculated from O2 consumption and from CO2 production provide estimates of toluene and p- xylene degradation rates within about ??50% of measured values when complete mineralization stoichiometry is assumed. Measured values ranged from 851.1 to 965.1 g m-3 year-1 for toluene, and 407.2-942.3 g m-3 year-1 for p- xylene. Contaminated sediment samples from a gasoline-spill site were used in a second set of microcosm experiments. Here, reaction rates of O2 and CO2 were measured and used to estimate hydrocarbon respiration rates. Total hydrocarbon reaction rates ranged from 49.0 g m-3 year-1 in uncontaminated (background) to 1040.4 g m-3 year-1 for highly contaminated sediment, based on CO2 production data. These rate estimates were similar to those obtained independently from in situ CO2 vertical gradient and flux determinations at the field site. In these experiments, aerobic conditions were maintained in the microcosms by using air as the replacement gas, thus preserving the ambient aerobic environment of the subsurface near the capillary zone. This would not be possible with closed microcosms.

Hydraulic parameters in eroding rills and their influence on detachment processes

NASA Astrophysics Data System (ADS)

Wirtz, Stefan; Seeger, Manuel; Zell, Andreas; Wagner, Christian; Wengel, René; Ries, Johannes B.

2010-05-01

In many experiments as well in laboratory as in field experiments the correlations between the detachment rate and different hydraulic parameters are calculated. The used parameters are water depth, runoff, shear stress, unit length shear force, stream power, Reynolds- and Froude number. The investigations show even contradictory results. In most soil erosion models like the WEPP model, the shear stress is used to predict soil detachment rates. But in none of the WEPP datasets, the shear stress showed the best correlation to the detachment rate. In this poster we present the results of several rill experiments in Andalusia from 2008 and 2009. With the used method, it is possible to measure the needed factors to calculate the mentioned parameters. Water depth is measured by an ultrasonic sensor, the runoff values are calculated by combining flow velocity and flow diameter. The parameters wetted perimeter, flow diameter and hydraulic radius can be calculated from the measured rill cross sections and the measured water levels. In the sample density values, needed for calculation of shear stress, unit length shear force and stream power, the sediment concentration and the grain density are are considered. The viscosity of the samples was measured with a rheometer. The result of this measurements shows, that there is a very high linear correlation (R² = 0.92) between sediment concentration and the dynamic viscosity. The viscosity seems to be an important factor but it is only used in the Reynolds-number-equation, in other equations it is neglected. But the viscosity value increases with increasing sediment concentration and hence the influence also increases and the in multiclications negiligible viscosity value of 1 only counts for clear water. The correlations between shear stress, unit length shear force and stream power at the x-axis and the detachment rate at the ordinate show, that there is not one fixed parameter that always displays the best correlation to the detachment rate. The best hit does not change from one experiment to another, it changes from one measuring point to another. Different processes in rill erosion are responsible for the changing correlations. In some cases no one of the parameters shows an acceptable correlation to the soil detachment, because these factors describe fluvial processes. Our experiments show, that not the fluvial processes cause the main sediment procduction in the rills, but bank failure or knickpoint and headcut retreat and these processes are more gravitative than fluvial. Another sediment producing process is the abrupt spill over of plunge pools, a process not realy fluvial and not realy gravitativ. In some experiments, the highest sediment concentrations were measured at the slowly flowing waterfront that only transports the loose material. But all these processes are not considered in soil erosion models. Hence, hydraulic parameters alone are not sufficient to predict detachment rates. They cover the fluvial incising in the rill's bottom, but the main sediment sources are not considered satisying in its equations.

Sediment Flux from Source to Sink in the Brazos-Trinity Depositional System

NASA Astrophysics Data System (ADS)

Pirmez, C.; Prather, B. E.; Droxler, A.; Ohayer, W.

2007-12-01

During the Late Pleistocene a series of intra-slope basins offshore Texas in the Western Gulf of Mexico, received a high influx of clastic sediments derived primarily from the Brazos, Trinity, and Mississippi rivers. Sediment failures initiated at shelf edge deltas resulted in mass flows that negotiate a complex slope and basin topography caused by salt tectonics. Sediment locally fill ponded basins eventually spilling into subsequent basins downstream. Interaction between these flows and slope topography leads to a complex partitioning of sediment over time and space that can only be unraveled with high-resolution data. The availability of system-wide coverage with conventional 3d seismic surveys, a dense grid of high-resolution 2d seismic lines and cored wells from two of the four linked intraslope basins, makes this locale an ideal area to investigate the transfer of sediment across the continental margin, from river sources to the ultimate sink within an enclosed intraslope basin. Data from IODP Expedition 308 and industry wells, combined with data from previous studies on the shelf constrain an integrated seismic stratigraphic framework for the depositional system. Numerous radiocarbon age dates coupled with multiple stratigraphic tools (seismic-, bio-, and tephra correlations and oxygen isotope measurements) provide an unprecedented high-resolution chronology that allow for detailed estimation of sedimentation rates in this turbidite system and calculation of sediment volumes in each of the basins over time intervals of a few millennia during the late Pleistocene. We find that rates of sedimentation exceed 10 m/kyr during some periods of ultra-fast turbidite accumulation. Rates of channel incision and tectonic subsidence can also be calculated and are comparable to the rapid accumulation rates measured in the basin fill. Our observations indicate that while sealevel changes exert a first order control on delivery of sediment to the basins, the sedimentary record suggests that delta dynamics, basin tectonics and the interaction between gravity flows and basin topography are equally important in determining the distribution of sediments in time and space along this depositional system.

Inverse modelling of fluvial sediment connectivity identifies characteristics and spatial distribution of sediment sources in a large river network.

NASA Astrophysics Data System (ADS)

Schmitt, R. J. P.; Bizzi, S.; Kondolf, G. M.; Rubin, Z.; Castelletti, A.

2016-12-01

Field and laboratory evidence indicates that the spatial distribution of transport in both alluvial and bedrock rivers is an adaptation to sediment supply. Sediment supply, in turn, depends on spatial distribution and properties (e.g., grain sizes and supply rates) of individual sediment sources. Analyzing the distribution of transport capacity in a river network could hence clarify the spatial distribution and properties of sediment sources. Yet, challenges include a) identifying magnitude and spatial distribution of transport capacity for each of multiple grain sizes being simultaneously transported, and b) estimating source grain sizes and supply rates, both at network scales. Herein, we approach the problem of identifying the spatial distribution of sediment sources and the resulting network sediment fluxes in a major, poorly monitored tributary (80,000 km2) of the Mekong. Therefore, we apply the CASCADE modeling framework (Schmitt et al. (2016)). CASCADE calculates transport capacities and sediment fluxes for multiple grainsizes on the network scale based on remotely-sensed morphology and modelled hydrology. CASCADE is run in an inverse Monte Carlo approach for 7500 random initializations of source grain sizes. In all runs, supply of each source is inferred from the minimum downstream transport capacity for the source grain size. Results for each realization are compared to sparse available sedimentary records. Only 1 % of initializations reproduced the sedimentary record. Results for these realizations revealed a spatial pattern in source supply rates, grain sizes, and network sediment fluxes that correlated well with map-derived patterns in lithology and river-morphology. Hence, we propose that observable river hydro-morphology contains information on upstream source properties that can be back-calculated using an inverse modeling approach. Such an approach could be coupled to more detailed models of hillslope processes in future to derive integrated models of hillslope production and fluvial transport processes, which is particularly useful to identify sediment provenance in poorly monitored river basins.

Flood-plain and channel aggradation of selected bridge sites in the Iowa and Skunk River basins, Iowa

USGS Publications Warehouse

Eash, D.A.

1996-01-01

Flood-plain and channel-aggradation rates were estimated at 10 bridge sites on the Iowa River upstream of Coralville Lake and at two bridge sites in the central part of the Skunk River Basin. Four measurement methods were used to quantify aggradation rates: (1) a dendrogeomorphic method that used tree-age data and sediment-deposition depths, (2) a bridge-opening cross-section method that compared historic and recent cross sections of bridge openings, (3) a stage-discharge rating-curve method that compared historic and recent stages for the 5-year flood discharge and the average discharge, and (4) nine sediment pads that were installed on the Iowa River flood plain at three bridge sites in the vicinity of Marshalltown. The sediment pads were installed prior to overbank flooding in 1993. Sediments deposited on the pads as a result of the 1993 flood ranged in depth from 0.004 to 2.95 feet. Measurement periods used to estimate average aggradation rates ranged from 1 to 98 years and varied among methods and sites. The highest aggradation rates calculated for the Iowa River Basin using the dendrogeomorphic and rating- curve measurement methods were for the State Highway 14 crossing at Marshalltown, where these highest rates were 0.045 and 0.124 feet per year, respectively. The highest aggradation rates calculated for the Skunk River Basin were for the U.S. Highway 63 crossing of the South Skunk River near Oskaloosa, where these highest rates were 0.051 and 0.298 feet per year, respectively.

High sedimentation rates and thrust fault modulation: Insights from ocean drilling offshore the St. Elias Mountains, southern Alaska

NASA Astrophysics Data System (ADS)

Worthington, Lindsay L.; Daigle, Hugh; Clary, Wesley A.; Gulick, Sean P. S.; Montelli, Aleksandr

2018-02-01

The southern Alaskan margin offshore the St. Elias Mountains has experienced the highest recorded offshore sediment accumulation rates globally. Combined with high uplift rates, active convergence and extensive temperate glaciation, the margin provides a superb setting for evaluating competing influences of tectonic and surface processes on orogen development. We correlate results from Integrated Ocean Drilling Program (IODP) Expedition 341 Sites U1420 and U1421 with regional seismic data to determine the spatial and temporal evolution of the Pamplona Zone fold-thrust belt that forms the offshore St. Elias deformation front on the continental shelf. Our mapping shows that the pattern of active faulting changed from distributed across the shelf to localized away from the primary glacial depocenter over ∼300-780 kyrs, following an order-of-magnitude increase in sediment accumulation rates. Simple Coulomb stress calculations show that the suppression of faulting is partially controlled by the change in sediment accumulation rates which created a differential pore pressure regime between the underlying, faulted strata and the overlying, undeformed sediments.

Lower Charles River Bathymetry: 108 Years of Fresh Water

NASA Astrophysics Data System (ADS)

Yoder, M.; Sacarny, M.

2017-12-01

The Lower Charles River is a heavily utilized urban river that runs between Cambridge and Boston in Massachusetts. The recreational usage of the river is dependent on adequate water depths, but there have been no definitive prior studies on the sedimentation rate of the Lower Charles River. The river transitioned from tidal to a freshwater basin in 1908 due to the construction of the (old) Charles River Dam. Water surface height on the Lower Charles River is maintained within ±1 foot through controlled discharge at the new Charles River Dam. The current study area for historical comparisons is from the old Charles River Dam to the Boston University Bridge. This study conducted a bathymetric survey of the Lower Charles River, digitized three prior surveys in the study area, calculated volumes and depth distributions for each survey, and estimated sedimentation rates from fits to the volumes over time. The oldest chart digitized was produced in 1902 during dam construction deliberations. The average sedimentation rate is estimated as 5-10 mm/year, which implies 1.8-3.5 feet sedimentation since 1908. Sedimentation rates and distributions are necessary to develop comprehensive management plans for the river and there is evidence to suggest that sedimentation rates in the shallow upstream areas are higher than the inferred rates in the study area.

Assessing sedimentation rates at Usumacinta and Grijalva river basin (Southern Mexico) using OSL and suspended sediment load analysis: A study from the Maya Classic Period

NASA Astrophysics Data System (ADS)

Munoz-Salinas, E.; Castillo, M.; Sanderson, D.; Kinnaird, T.; Cruz-Zaragoza, E.

2013-12-01

Studying sedimentation rates on floodplains is key to understanding environmental changes occurred through time in river basins. The Usumacinta and Grijalva rivers flow most of their travel through the southern part of Mexico, forming a large river basin, crossing the states of Chiapas and Tabasco. The Usumacinta-Grijalva River Basin is within the 10 major rivers of North America, having a basin area of ~112 550 km2. We use the OSL technique for dating two sediment profiles and for obtaining luminescence signals in several sediment profiles located in the streambanks of the main trunk of the Usumacinta and Grijalva rivers. We also use mean annual values of suspended sediment load spanning ~50 years to calculate the sedimentation rates. Our OSL dating results start from the 4th Century, when the Maya Civilization was at its peak during the Classic Period. Sedimentation rates show a notable increase at the end of the 19th Century. The increase of the sedimentation rates seems to be related to changes in land uses in the Sierra Madre de Chiapas and Altos de Chiapas, based on deforestation and land clearing for developing new agrarian and pastoral activities. We conclude that the major environmental change in the basin of the Usumacinta and Grijalva Rivers since the Maya Classic Period was generated since the last Century as a result of an intense anthropogenic disturbance of mountain rain forest in Chiapas.

Topography and Sedimentation Characteristics of the Squaw Creek National Wildlife Refuge, Holt County, Missouri, 1937-2002

USGS Publications Warehouse

Heimann, David C.; Richards, Joseph M.

2003-01-01

The Squaw Creek National Wildlife Refuge (hereafter referred to as the Refuge), located on the Missouri River floodplain in northwest Missouri, was established in 1935 to provide habitat for migratory birds and wildlife. Results of 1937 and 1964 topographic surveys indicate that sedimenta-tion, primarily from Squaw Creek and Davis Creek inflows, had substantially reduced Refuge pool volumes and depths. A study was undertaken by the U.S. Geological Survey, in cooperation with the U.S. Fish and Wildlife Service, to quantify and spatially analyze historic rates of sedimentation in the Refuge and determine the surface elevations, depths, and pool capacities for selected managed pools from a 2002 survey.The 1937 to 1964 mean total sediment depo-sition, in the area corresponding to the 2002 sur-veyed pool area (about 4,900 acres), was 1.26 ft (feet), or 0.047 ft/yr (foot per year). Mean annual rates of deposition, by pool, from 1937 to 1964 varied from 0.016 to 0.083 ft/yr. From 1964 to 2002, the mean total sediment deposition in the 2002 surveyed pools was 0.753 ft, or 0.020 ft/yr. Therefore, the mean rate of sediment-depth accu-mulation from 1964 to 2002 was about 42 percent of the mean 1937 to 1964 rate, or a 58 percent reduction. Mean annual rates of deposition by pool from 1964 to 2002 varied from 0.010 to 0.049 ft/yr. Despite a substantial reduction in the average sediment accumulation rate for the Refuge, 5 of the 15 separate pools for which annual rates were calculated for both periods showed a small increase in the deposition rates of up to 0.008 ft/yr. Sediment deposits have resulted in a sub-stantial cumulative loss of volume in the Refuge pools since 1937. The 1937 to 2002 total sediment volume deposited in the 2002 surveyed pool area was about 9,900 acre-ft (acre-feet), or 152 acre-ft/yr (acre-feet per year). The volume of sediment deposited from 1937 to 1964 for these pools was about 6,200 acre-ft, or 230 acre-ft/yr. The volume deposited from 1964 to 2002 was about 3,700 acre-ft, or 97.3 acre-ft/yr.Bulk density values were determined from sediment cores collected from 22 sites in the Ref-uge and the bulk densities, along with sediment volumes, allowed for the calculation of sediment mass contributions to the Refuge. From 1937 to 2002, about 10,300,000 tons of sediment were deposited in the 2002 surveyed area, or 32.4 tons/acre/yr (tons per acre per year). The total computed mass of sediment deposited between 1937 and 1964 was about 6,510,000 tons, or an average of 49.1 tons/acre/yr. The total mass depos-ited from 1964 to 2002 in surveyed pools was about 3,830,000 tons, or an average of 20.5 tons/acre/yr. As with sediment thickness compari-sons, the rate of sediment mass deposition between 1964 to 2002 was about 42 percent of that from 1937 to 1964, or a 58 percent reduction.The greatest amounts of sediment deposition in the Refuge for 1937 to 2002 have been near the Squaw Creek and Davis Creek inflow spillway locations. Sediment depths in some areas near former inflow locations have exceeded 8 ft. Relo-cation of an inflow spillway effectively reduced additional sediment deposition at the original loca-tion, and caused increased sedimentation at the new inflow location. This is most clearly depicted in a pool located in the north section of the Refuge that directly received Squaw Creek inflows from 1937 to 1964 and had a mean deposition rate of 0.081 ft/yr reduced to 0.012 ft/yr, from 1964 to 2002, after inflows were redirected and erosion-management plans were implemented in the con-tributing basins.

A closer look at the Neogene erosion and accumulation rate increase

NASA Astrophysics Data System (ADS)

Willenbring, J.; von Blanckenburg, F.

2008-12-01

Glacial erosion and Quaternary cold-stage warm-stage climate cycling have been cited as mechanisms to explain observations of increased Neogene marine sedimentation rates. Quantification of long-term glacial erosion rates from cosmogenic radionuclides from large areas mostly covered by cold-based ice during the Quaternary show very low erosion rates over several glacial cycles. In addition, isotope ratio proxies of dissolved metals in seawater, measured in chemical ocean sediments, lack clear evidence for an increase in terrigenous denudation. In particular, the stable isotope 9Be, derived from continental erosion, shows no change in its ratio to meteoric cosmogenic nuclide 10Be, derived from rain over the past 10 My. Radiogenic Pb and Nd isotopes, mainly show a change in the style of denudation from more chemical to more physical processes in the Quaternary. These data are at odds with a suggested increase in marine sedimentation rates during the late Cenozoic. In order to resolve this contradiction we have scrutinized these sedimentation rate calculations from ocean cores to identify whether they might show only apparent increases in the Neogene sections. Potential explanations are that in some cases, measured sediment thicknesses for different time intervals lack corrections for sediment compaction. Compaction of the lower portions of the cores drastically increases the apparent thickness of the more recent (Quaternary) sediment. In addition, sedimentation rates often only appear higher for recent sections in cores due to an artifact of an averaging timescale that decreases up-core. Such an averaging time scale decrease arises from better chronological resolution in recent times (Sadler et al., 1999). Cannibalization of older sediment might add to this effect. Together, these data question a clear, global-scale Quaternary climate-erosion connection that would be unique in Earth's history.

Response of a tidal freshwater marsh to changes in sea level and suspended-sediment concentrations

NASA Astrophysics Data System (ADS)

Palinkas, C. M.

2016-02-01

Tidal marshes are among the world's most valuable ecosystems from a variety of perspectives, but they are also perhaps the most threatened by environmental changes, such as increased rates of sea-level rise and decreased concentrations of fluvial suspended sediments. In this study, time-series measurements of sedimentation over 5 years (2010-2014) at Dyke Marsh Preserve (Potomac River, VA, USA) are used to evaluate the influence of environmental drivers on sediment accretion within the marsh. To do so, bimonthly (deposition on ceramic tiles) and seasonal-scale (from 7Be (half-life 53.3 d) measurements) sedimentation rates are placed in the context of factors that can influence inorganic sediment availability and delivery to the marsh platform, specifically winds, river discharge, suspended-sediment concentrations (SSC; calculated from rating curves), and local sea level. Because of marsh geography and dominant storm patterns in this area, the influence of events is complex - wind speed and direction are negatively correlated with local sea level but positively correlated with SSC. This is, stronger winds from a more westerly direction drive water seaward of the marsh platform; increased precipitation results in higher river discharge and SSC from runoff and/or sediment resuspension. At the bimonthly scale, changes in sea level are correlated with both the rate and character (organic content) of sediments collected on tiles, but there was no relationship between sedimentation rates and SSC. Instead, bimonthly sedimentation rates are correlated with the fluvial sediment load (product of river discharge and SSC), which is not often included in models of marsh accretion. These trends are similar for seasonal-scale observations, though statistical tests are not as robust. These results suggest that, while events drive sedimentation within the marsh, their influence can be obscured over longer time scales that incorporate quiescent times of non-deposition.

10Be constrains the sediment sources and sediment yields to the Great Barrier Reef from the tropical Barron River catchment, Queensland, Australia

NASA Astrophysics Data System (ADS)

Nichols, K. K.; Bierman, P. R.; Rood, D. H.

2014-12-01

Estimates of long-term, background sediment generation rates place current and future sediment fluxes to the Great Barrier Reef in context. Without reliable estimates of sediment generation rates and without identification of the sources of sediment delivered to the reef prior to European settlement (c. 1850), determining the necessity and effectiveness of contemporary landscape management efforts is difficult. Using the ~2100-km2 Barron River catchment in Queensland, Australia, as a test case, we use in situ-produced 10Be to derive sediment generation rate estimates and use in situ and meteoric 10Be to identify the source of that sediment, which enters the Coral Sea near Cairns. Previous model-based calculations suggested that background sediment yields were up to an order of magnitude lower than contemporary sediment yields. In contrast, in situ 10Be data indicate that background (43 t km-2 y-1) and contemporary sediment yields (~45 t km-2 y-1) for the Barron River are similar. These data suggest that the reef became established in a sediment flux similar to what it receives today. Since western agricultural practices increased erosion rates, large amounts of sediment mobilized from hillslopes during the last century are probably stored in Queensland catchments and will eventually be transported to the coast, most likely in flows triggered by rare but powerful tropical cyclones that were more common before European settlement and may increase in strength as climate change warms the south Pacific Ocean. In situ and meteoric 10Be concentrations of Coral Sea beach sand near Cairns are similar to those in rivers on the Atherton Tablelands, suggesting that most sediment is derived from the extensive, low-gradient uplands rather than the steep, more rapidly eroding but beach proximal escarpment.

Simulated oil release from oil-contaminated marine sediment in the Bohai Sea, China.

PubMed

Yuan, Lingling; Han, Longxi; Bo, Wenjie; Chen, Hua; Gao, Wenshen; Chen, Bo

2017-05-15

There is a high degree of heavy oil partitioning into marine sediments when an oil spill occurs. Contaminated sediment, as an endogenous pollution source, can re-pollute overlying water slowly. In this study, a static oil release process and its effects in marine sediment was investigated through a series of experiments with reproductive heavy oil-contaminated marine sediment. The oil release process was accurately simulated with a Lagergren first-order equation and reached equilibration after 48h. The fitted curve for equilibrium concentration (C 0 ) and first-order rate constant (k 1 ) for sediment pollution levels exhibited a first-order log relationship. The instantaneous release rate (dC t dt) was also calculated. The C 0 increased with increases in temperature and dissolved organic matter (DOM), and decreasing salinity. The k 1 increased with temperature, but was not affected by DOM and salinity. These results can be used to better understand the fate of heavy oil in contaminated sediments of the Bohai Sea. Copyright © 2017. Published by Elsevier Ltd.

Anaerobic methane oxidation coupled to denitrification is the dominant methane sink in a deep lake

PubMed Central

Deutzmann, Joerg S.; Stief, Peter; Brandes, Josephin; Schink, Bernhard

2014-01-01

Anaerobic methane oxidation coupled to denitrification, also known as “nitrate/nitrite-dependent anaerobic methane oxidation” (n-damo), was discovered in 2006. Since then, only a few studies have identified this process and the associated microorganisms in natural environments. In aquatic sediments, the close proximity of oxygen- and nitrate-consumption zones can mask n-damo as aerobic methane oxidation. We therefore investigated the vertical distribution and the abundance of denitrifying methanotrophs related to Candidatus Methylomirabilis oxyfera with cultivation-independent molecular techniques in the sediments of Lake Constance. Additionally, the vertical distribution of methane oxidation and nitrate consumption zones was inferred from high-resolution microsensor profiles in undisturbed sediment cores. M. oxyfera-like bacteria were virtually absent at shallow-water sites (littoral sediment) and were very abundant at deep-water sites (profundal sediment). In profundal sediment, the vertical distribution of M. oxyfera-like bacteria showed a distinct peak in anoxic layers that coincided with the zone of methane oxidation and nitrate consumption, a strong indication for n-damo carried out by M. oxyfera-like bacteria. Both potential n-damo rates calculated from cell densities (660–4,890 µmol CH4⋅m−2⋅d−1) and actual rates calculated from microsensor profiles (31–437 µmol CH4⋅m−2⋅d−1) were sufficiently high to prevent methane release from profundal sediment solely by this process. Additionally, when nitrate was added to sediment cores exposed to anoxic conditions, the n-damo zone reestablished well below the sediment surface, completely preventing methane release from the sediment. We conclude that the previously overlooked n-damo process can be the major methane sink in stable freshwater environments if nitrate is available in anoxic zones. PMID:25472842

Anaerobic methane oxidation coupled to denitrification is the dominant methane sink in a deep lake.

PubMed

Deutzmann, Joerg S; Stief, Peter; Brandes, Josephin; Schink, Bernhard

2014-12-23

Anaerobic methane oxidation coupled to denitrification, also known as "nitrate/nitrite-dependent anaerobic methane oxidation" (n-damo), was discovered in 2006. Since then, only a few studies have identified this process and the associated microorganisms in natural environments. In aquatic sediments, the close proximity of oxygen- and nitrate-consumption zones can mask n-damo as aerobic methane oxidation. We therefore investigated the vertical distribution and the abundance of denitrifying methanotrophs related to Candidatus Methylomirabilis oxyfera with cultivation-independent molecular techniques in the sediments of Lake Constance. Additionally, the vertical distribution of methane oxidation and nitrate consumption zones was inferred from high-resolution microsensor profiles in undisturbed sediment cores. M. oxyfera-like bacteria were virtually absent at shallow-water sites (littoral sediment) and were very abundant at deep-water sites (profundal sediment). In profundal sediment, the vertical distribution of M. oxyfera-like bacteria showed a distinct peak in anoxic layers that coincided with the zone of methane oxidation and nitrate consumption, a strong indication for n-damo carried out by M. oxyfera-like bacteria. Both potential n-damo rates calculated from cell densities (660-4,890 µmol CH4⋅m(-2)⋅d(-1)) and actual rates calculated from microsensor profiles (31-437 µmol CH4⋅m(-2)⋅d(-1)) were sufficiently high to prevent methane release from profundal sediment solely by this process. Additionally, when nitrate was added to sediment cores exposed to anoxic conditions, the n-damo zone reestablished well below the sediment surface, completely preventing methane release from the sediment. We conclude that the previously overlooked n-damo process can be the major methane sink in stable freshwater environments if nitrate is available in anoxic zones.

Production of carbonate sediments by a unicellular green alga

USGS Publications Warehouse

Yates, K.K.; Robbins, L.L.

1998-01-01

This study investigates the ability of the unicellular green alga Natmochloris atoimis to precipitate CaCO3, quantifies mineral precipitation rates, estimates sediment production in a N. atomiis bloom, and discusses the implications of microbial calcification for carbonate sediment deposition. A series of N. atomus cultures, isolated from Lake Reeve, Australia, were incubated at various pH and calcium concentrations to determine environmental parameters for calcification. Rates of calcification were calculated from initial and postincubation alkalinity, pH, and calcium measurements. Replicate experiments and controls consisting of non-calcifying cultures, uninoculated media, and dead cell cultures were performed using environmental culture parameters determined in series cultures. Average calcification rates from replicate experiments were used to predict daily sediment production rates in a small bloom of N. atomus. N. atomus precipitates 0.138 g/L of calcite in approximately 4 h when incubated at pH 8.5, 14.24 mM calcium concentration, 33 ??C, 100 ??E/m2/s light intensity, and a cell population density of 107 cells/mL. Assuming continuous precipitation, this corresponds to a maximum estimated sediment production rate of 1.6 ?? 106 kg of CaCO3, per 12 h day in a single bloom of 3.2 ?? 109 L. Our results suggest that microbial calcification contributes significantly to the carbonate sediment budget.

Aggregation Rates of Sediments (Montmorillonite, Kaolinite, Illite and Goethite) with the Enveloped Φ6 Bacteriophage

NASA Astrophysics Data System (ADS)

Katz, A.; Block, K. A.; Peña, S.; Alimova, A.; Gottlieb, P.

2015-12-01

The interaction between sediments and viruses has been studied extensively from the prospective of virus survivability and infectivity. However, the role of soil organisms, including viruses in C and N sequestration in soil has not been studied as extensively. Φ6, a member of the cystoviridae family, is a bacteriophage that infects Pseudomonas syringae, a common plant pathogen known to readily form biofilms.The small mineral fraction (< 0.2 μm) of soil and Φ6 are colloidal particles, therefore aggregation can be explained by DLVO (Derjaguin & Landau, Verwey & Overbeek) theory. Time-resolved visible-light turbidity measurements were used to calculate the heteroaggregation rates of Φ6 with the sediments. Samples were suspended in a low-concentration cation buffer so that the kinetics were in the reaction limited cluster aggregation (RLCA) regime in where the probability of two particles adhering after collision is determined by the interaction forces between the particles.At neutral pH to slightly acidic pH, Φ6 is slightly negatively charged; montmorillonite and illite are negatively charged; and kaolinite and goethite are positively charged. In isolation, neither Φ6 nor the sediments aggregated in the modified buffer. However, in mixtures, Φ6 and montmorillonite, and Φ6 and illite, exhibited increases in turbidity, indicating heteroaggregation. Neither Φ6 and kaolinite, nor Φ6 and goethite, exhibited increased turbidity upon mixing indicating little or no aggregation. These results suggest that the interaction of the virus with the sediments is governed by hydrophobic rather than electrostatic forces. Heteroaggregation rates were calculated from the time rate of change of the turbidity.

Improving Bedload Transport Predictions by Incorporating Hysteresis

NASA Astrophysics Data System (ADS)

Crowe Curran, J.; Gaeuman, D.

2015-12-01

The importance of unsteady flow on sediment transport rates has long been recognized. However, the majority of sediment transport models were developed under steady flow conditions that did not account for changing bed morphologies and sediment transport during flood events. More recent research has used laboratory data and field data to quantify the influence of hysteresis on bedload transport and adjust transport models. In this research, these new methods are combined to improve further the accuracy of bedload transport rate quantification and prediction. The first approach defined reference shear stresses for hydrograph rising and falling limbs, and used these values to predict total and fractional transport rates during a hydrograph. From this research, a parameter for improving transport predictions during unsteady flows was developed. The second approach applied a maximum likelihood procedure to fit a bedload rating curve to measurements from a number of different coarse bed rivers. Parameters defining the rating curve were optimized for values that maximized the conditional probability of producing the measured bedload transport rate. Bedload sample magnitude was fit to a gamma distribution, and the probability of collecting N particles in a sampler during a given time step was described with a Poisson probability density function. Both approaches improved estimates of total transport during large flow events when compared to existing methods and transport models. Recognizing and accounting for the changes in transport parameters over time frames on the order of a flood or flood sequence influences the choice of method for parameter calculation in sediment transport calculations. Those methods that more tightly link the changing flow rate and bed mobility have the potential to improve bedload transport rates.

Inconsistencies between 14C and short-lived radionuclides-based sediment accumulation rates: Effects of long-term remineralization.

PubMed

Baskaran, M; Bianchi, T S; Filley, T R

2017-08-01

14 C is the most widely utilized geochronometer to investigate geological, geochemical and geophysical problems over the past 5 decades. Establishment of precise sedimentation rates is crucial for the reconstruction of paleo-climate, -ecological and - environmental studies when extrapolation of sedimentation rates is utilized for time scales beyond the dating range. However, agreement between short-term and long-term sedimentation rates in anthropogenically unperturbed sediment cores has not been shown. Here we show that the AMS 14 C-based long-term mass accumulation rate (MAR) of an organic-rich (>70%) sediment core from Mud Lake, Florida to be ∼5 times lower than the short-term MAR obtained using 239,240 Pu, 137 Cs and excess 210 Pb ( 210 Pb xs ). The measured sediment inventories of 210 Pb xs , 137 Cs and 239,240 Pu are comparable to the atmospheric fallout for the sampling site, indicating very little accelerated sediment erosion over the past several decades. Presence of sharp fallout peaks of 239,240 Pu indicates very little sediment mixing. The penetration depths of 137 Cs and 239,240 Pu were found to be much deeper than expected and this is attributed to their post-depositional mobility. MAR calculated using 14 C-ages in successive layers also indicated decreasing MARs with depth, and was reflective of progressive remineralization. Using first-order kinetics, the sediment remineralization rate was found to be 4.4 × 10 -4 y -1 and propose that over the long-term, remineralization of organic-rich sediment affected the long-term MAR, but not the ratio of 14 C/ 12 C. Thus, the MAR and linear sedimentation rate obtained using 14 C (and other isotope-based methods) could be erroneous, although 14 C ages may not be affected by such remineralization. Long-term remineralization rates of organic matter has a direct bearing on the biogeochemical cycling of elements in aqueous systems and mass balance of elements needs to be taken into consideration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Shoreline erosion and decadal sediment accumulation in the Tar-Pamlico estuary, North Carolina, USA: A source-to-sink analysis

NASA Astrophysics Data System (ADS)

Eulie, Devon O.; Corbett, D. Reide; Walsh, J. P.

2018-03-01

Estuaries contain vital habitats and it is important to understand how these areas respond to human activities and natural processes such as sea-level rise and wave attack. As estuarine shorelines erode or become modified with hard structures, there is potential for significantly altering the availability of sediment and the filling of coastal systems. This study used a source-to-sink approach and quantified rates of shoreline erosion in the Tar-Pamlico sub-estuary, a tributary of the larger Albemarle-Pamlico Estuarine System (APES). The average shoreline change rate (SCR) determined using an end-point method was -0.5 ± 0.9 m yr-1 for the Tar-Pamlico. Incorporating bulk density estimates, this contributes 0.6 × 105 tons of fine sediment to the system annually, or after accounting for fluvial input, about 40% of the total sediment supply to the sub-estuary. The role of the Tar-Pamlico as a sink for these sediments was addressed using the radionuclide tracers 210Pb and 137Cs. Radionuclide activities and sediment accumulation rates identified several depositional regions, in particular in the middle of the estuary. Linear sediment accumulation rates ranged from 0.10 ± 0.02 to 0.38 ± 0.02 g cm-2 yr-1, and total storage of fine sediment in the system was 1.6 × 105 t yr-1. It was not possible to confidently discern a change in the rate of shoreline erosion or seabed accumulation. A preliminary budget for fine sediments (grain-size <63 μm) was then calculated to compare erosional sources with sedimentary sinks. Almost all (∼93.0%) of the fine sediment entering the system was accumulated and stored, while only about 7.0% was exported to Pamlico Sound.

Current subsidence rates due to compaction of Holocene sediments in southern Louisiana

USGS Publications Warehouse

Meckel, T.A.; ten Brink, Uri S.; Williams, S.J.

2006-01-01

Relative contributions of geologic and anthropogenic processes to subsidence of southern Louisiana are vigorously debated. Of these, shallow sediment compaction is often considered dominant, although this has never been directly observed or effectively demonstrated. Quantitative understanding of subsidence is important for predicting relative sea level rise, storm surge flooding due to hurricanes, and for successful wetland restoration. Despite many shallow borings, few appropriate stratigraphic and geotechnical data are available for site-specific calculations. We overcome this by determining present compaction rates from Monte Carlo simulations of the incremental sedimentation and compaction of stratigraphies typical of the Holocene of southern Louisiana. This approach generates distributions of present compaction rates that are not expected to exceed 5 mm/yr, but may locally. Locations with present subsidence rates greater than the predicted maximum probable shallow compaction rates are likely influenced by additional processes.

Calculating erosion rates of river bank sediment by combining field measurements of erodibility parameters and small-scale topographic features – A case study at the Danube River

USDA-ARS?s Scientific Manuscript database

This paper examines the application of a method for calculating fluvial erosion on river banks. In the investigated area the determination of potential erosion rates are essential to estimating the initiated river widening processes and their effect on navigation. A mini-jet device was employed, for...

Sedimentation Survey of Lago Icacos, Puerto Rico, March 2004

USGS Publications Warehouse

Soler-López, Luis R.

2007-01-01

The Lago Icacos, a small reservoir built in 1930 and owned by the Puerto Rico Electric Power Authority, is part of the Rio Blanco Hydroelectric Power System. The reservoir is located in Naguabo, within the Caribbean National Forest in eastern Puerto Rico. The original storage capacity of the reservoir was 19,119 cubic meters in 1930. The bathymetric survey conducted by the U.S. Geological Survey in March 2004 indicates a storage capacity of 7,435 cubic meters or 39 percent of the original storage capacity, and a maximum depth of 5.3 meters. The reservoir has been dredged several times to restore lost storage capacity caused by high sediment loads and the frequent landslides that occur upstream from the dam, which have partially or completely filled the Lago Icacos. Because sediment removal activities have not been documented, sedimentation rates could not be determined using storage volume comparisons. A reservoir sedimentation rate was calculated using the daily sediment load data gathered at the U.S. Geological Survey Rio Icacos streamflow station upstream of the reservoir, the estimated Lago Icacos sediment trapping efficiency, and the estimated sediment yield of the Lago Icacos basin extrapolated from the Rio Icacos sediment load data. Using these properties, the Lago Icacos sedimentation rate was estimated as 71 cubic meters per year, equivalent to about 1 percent of the original storage capacity per year. The Lago Icacos 7.47-square-kilometer drainage area sediment yield was estimated as 7,126 tonnes per year or about 954 tonnes per square kilometer per year. Based on the current estimated sedimentation rate of 71 cubic meters per year, Lago Icacos has a useful life of about 105 years or to year 2109.

Luminescence (IRSL) dating of Yeni Rabat church in Artvin, Turkey

NASA Astrophysics Data System (ADS)

Şahiner, Eren; Meriç, Niyazi; Uygun, Selda

2013-05-01

Luminescence dating is a chronological method that has been used extensively in terrestrial materials. In this study, we present Infrared Stimulated Luminescence (IRSL) dating results obtained for sediment and pottery samples taken from Yeni Rabat Church, Ardanuç, Artvin, Turkey. For this purpose, equivalent dose (ED) and annual dose rate (AD) of samples were measured. For annual dose rate, concentrations of radioactive isotopes (U, Th, K) were determined by using a high-purity germanium detector. For the equivalent dose, polymineral fine grain SAR (Single Aliquot Regenerative Dose) and MAAD (Multiple Aliquot Additive Dose) procedures were used. The optimal preheat temperature was determined for sediment and pottery samples. Ages were calculated by Aitken's luminescence age calculation method, which found 710±190 years for the pottery sample and 1450±370 years, 1390±420 years, 1430±310 years, 2210±520 years and 1640±390 years for different sediment samples, respectively. These estimated age ranges support the theory that Yeni Rabat Church could have been constructed in medieval times.

Assessment of contemporary erosion/sedimentation rates trend within a small well-cultivated catchments using caesium-137 as a chronomarker (on the example of the Republic of Tatarstan, Russia)

NASA Astrophysics Data System (ADS)

Sharifullin, Aidar; Gusarov, Artem; Gafurov, Artur; Golosov, Valentin

2017-04-01

An analysis of sedimentation at a first order valley bottoms allows us to receive a sufficiently reliable quantitative evaluation of soil losses from the catchment area for two time intervals: 1963-1986 and 1987-2015 and its temporal variability. The studied catchment "Temeva River" with total area 1.13 km2 is located in the northwestern part of the Republic of Tatarstan (the Myósha river basin). Combination methods and approaches were used for evaluation of sediment redistribution for the both time intervals, including detail geodetic survey of the main morphological units of the valley, large scale geomorphological mapping, cesium-137 technique for the sediment dating in the typical locations of the valley bottom, calculation of soil losses using modified version of USLE and State Hydrological Institute models. In addition available information was collected from the local meteorological stations about some climate characteristics dynamics for the period 1950-2015. Landsat images were applied for evaluation of possible changes of land use. Crop management coefficients were calculated separately for the rainfall season and snow-melt using available data about crop-rotation dynamics for the last 55 years. In the results it was found the significant decrease of average annual soil losses from the cultivated part of the "Temeva River" catchment for the period 1987-2015 if it is compare with period 1963-1986. Such conclusion is mainly based on the different sedimentation rates in the valley bottom: for the period of 1963-1986 the average sedimentation rates were 0.92-1.81 cm per year, while the period of 1987-2015 the rates were 0.17-0.50 cm per year. The main reason for this significant decrease sediment redistribution within the catchment is the reduction of surface runoff caused by climate warming in the region. It is led to the reduction of soils freezing depth and water reserves in a snow cover before the snow-melt, and to the sharp decline in the frequency of extreme (storm) precipitation (>50 mm per a day). The influence of agricultural activity on the erosion and sedimentation changeability was insignificant, although some regional variation of crop rotation including an increase in the proportion of perennial grasses obviously caused the decline in soil losses during warm period of year. The similar trend of erosion/sedimentation rates due to mostly climate changes was identified for south-western sector of the East European Plain, but the more serious reduction of erosion rates is established for the Middle Volga region. Keywords: erosion, sedimentation, sediment, caesium-137, dry valley, small catchment, cultivated lands, Republic of Tatarstan, East European Plain.

Verification of flux measurements made with in situ benthic chambers

NASA Astrophysics Data System (ADS)

Devol, Allan H.

1987-06-01

Exchange of solutes between the sediments and overlying water was measured in situ at two locations where the overlying waters were devoid of dissolved oxygen (Skan Bay, Alaska and the Tres Marias depression on the Mexican continental shelf). Measurements were made with a tripod capable of collecting eight sequential samples for analysis of dissolved gases and ions. The tripod also permitted tracer injection and the retrieval of sediments underlying the flux chambers. Because of the absence of oxygen, sediments from these areas did not contain benthic faunal populations, and it was possible to compare the benthic fluxes measured with the tripod with those calculated from pore water profiles. For solutes for which exchange was not limited by resistance in the diffuse sublayer (alkalinity, Si(OH) 4+, NH 4+, and PO 43-), tje 11 tirpod-measured fluxes agreed with those calculated from pore water gradients to within 25%. Benthic boundary layer thickness within the chambers as calculated from the initial rate of radiotracer uptake (tritiated water) varied from 405 to 605 μm in stirred chambers. Measured rates of NO 3- uptake were concordant with a boundary layer thickness of 600 μm.

Effect of water-column pH on sediment-phosphorus release rates in Upper Klamath Lake, Oregon, 2001

USGS Publications Warehouse

Fisher, Lawrence H.; Wood, Tamara M.

2004-01-01

Sediment-phosphorus release rates as a function of pH were determined in laboratory experiments for sediment and water samples collected from Shoalwater Bay in Upper Klamath Lake, Oregon, in 2001. Aerial release rates for a stable sediment/water interface that is representative of the sediment surface area to water column volume ratio (1:3) observed in the lake and volumetric release rates for resuspended sediment events were determined at three different pH values (8.1, 9.2, 10.2). Ambient water column pH (8.1) was maintained by sparging study columns with atmospheric air. Elevation of the water column pH to 9.2 was achieved through the removal of dissolved carbon dioxide by sparging with carbon dioxide-reduced air, partially simulating water chemistry changes that occur during algal photosynthesis. Further elevation of the pH to 10.2 was achieved by the addition of sodium hydroxide, which doubled average alkalinities in the study columns from about 1 to 2 milliequivalents per liter. Upper Klamath Lake sediments collected from the lake bottom and then placed in contact with lake water, either at a stable sediment/water interface or by resuspension, exhibited an initial capacity to take up soluble reactive phosphorus (SRP) from the water column rather than release phosphorus to the water column. At a higher pH this initial uptake of phosphorus is slowed, but not stopped. This initial phase was followed by a reversal in which the sediments began to release SRP back into the water column. The release rate of phosphorus 30 to 40 days after suspension of sediments in the columns was 0.5 mg/L/day (micrograms per liter per day) at pH 8, and 0.9 mg/L/day at pH 10, indicating that the higher pH increased the rate of phosphorus release by a factor of about two. The highest determined rate of release was approximately 10% (percent) of the rate required to explain the annual internal loading to Upper Klamath Lake from the sediments as calculated from a lake-wide mass balance and observed in total phosphorus data collected at individual locations.

Continuous In Situ Measurements of Near Bottom Chemistry and Sediment-Water Fluxes with the Chimney Sampler Array (CSA)

NASA Astrophysics Data System (ADS)

Martens, C. S.; Mendlovitz, H. P.; White, B. L.; Hoer, D.; Sleeper, K.; Chanton, J.; Wilson, R.; Lapham, L.

2011-12-01

The Chimney Sampler Array (CSA) was designed to measure in situ chemical and physical parameters within the benthic boundary layer plus methane and oxygen sediment-water chemical fluxes at upper slope sites in the northern Gulf of Mexico. The CSA can monitor temporal changes plus help to evaluate oceanographic and sub-seafloor processes that can influence the formation and stability of gas hydrates in underlying sediments. The CSA consists of vertical cylinders (chimneys) equipped with internal chemical sensors and with laboratory flume-calibrated washout rates. Chimney washout rates multiplied by chimney mean versus ambient concentrations allow calculation of net O2 and methane sediment-water fluxes. The CSA is emplaced on the seafloor by a ROVARD lander using a ROV for chimney deployments. The CSA presently includes two 30 cm diameter by 90 cm length cylinders that seal against the sediment with lead pellet beanbags; within each chimney cylinder are optode, conductivity and methane sensors. The CSA's data logger platform also includes pressure and turbidity sensors external to the chimneys along with an acoustic Doppler current meter to measure temporal variation in ambient current velocity and direction. The CSA was deployed aboard a ROVARD lander on 9/13/2010 in the northern Gulf of Mexico (Lat. 28 51.28440, Long. 088 29.39421) on biogeochemically active sediments within Block MC-118. A ROV was utilized for chimney deployment away from the ROVARD lander. The CSA monitored temporal changes in water column physical parameters, obtained near-bottom chemical data to compare with pore fluid and sediment core measurements and measured temporal variability in oxygen and methane sediment-water fluxes at two closely spaced stations at MC-118. A continuous, three-week data set was obtained that revealed daily cycles in chemical parameters and episodic flux events. Lower than ambient chimney dissolved O2 concentrations controlled by temporal variability in washout rates were used to calculate sediment O2 demand. Episodic events yielding turbidity spikes produced episodic spikes in chimney methane concentrations and sediment-water fluxes. The robust data set reveals new capabilities for long-term monitoring of near-bottom processes in biogeochemically active, continental margin environments.

Modelling detrital coral grain-size and age: Insights from sediment abrasion process of Yongle Atoll of South China Sea

NASA Astrophysics Data System (ADS)

Li, Y.; Zou, X.; Ge, C.; Tan, M.; Wang, C.

2017-12-01

Reef islands situated on the rims of atolls are composed almost exclusively of bioclastic materials locally supplied from adjacent coral reefs. Major skeletal component of these islands include coral, coralline algae, mollusks and foraminifera, produced in adjacent reefs. As the island builder, the bioclastic material is the sedimentary products, which also is the point of penetration to decipher the process. The bioclast of coral islands decrease in size with the transportation process. The grain-size provides a proxy record for the abrasion history of the unconsolidated sediment. The 230Th age of coral record the abrasion time. We hereby present a model to calculate the abrasion rate based on the data of 230Th age and grain-size of Yongle Atoll of Xisha Island, South China Sea. The grain size pattern in Yongle Atoll environment have confirm that the coral article diminution behave exponentially. The sediment composition of Yongle Atoll is identified, coral is dominant sediment constituent and the Th230 age is shown to exert an age distribution characteristics of coral detritus. We illustrate this approach by calculate the coral debris age of Xude Atoll, which located near the Yongle Atoll and then by comparing actual measured age and calculated age and to explore the dependence of the model. Observed 230 Th ages are well matched by predicted ages for medium age sediment. A poorer match for young and old sediment may result from some combination of large analytical uncertainties in the detrital ages and inhomogeneous erosion rates within the atoll. Such mismatches emphasize the need for more accurate kinematic models and for sampling strategies that are adapted to atoll-specific geologic and geomorphic conditions. Results presented constitute important new insights into regional sediment abrasion processed and on the evolution of coral atoll islands.

Anthropogenically induced changes in sediment and biogenic silica fluxes in Chesapeake Bay

USGS Publications Warehouse

Colman, Steven M.; Bratton, John F.

2003-01-01

Sediment cores as long as 20 m, dated by 14C, 210Pb, and 137Cs methods and pollen stratigraphy, provide a history of diatom productivity and sediment-accumulation rates in Chesapeake Bay. We calculated the flux of biogenic silica and total sediment for the past 1500 yr for two high-sedimentation-rate sites in the mesohaline section of the bay. The data show that biogenic silica flux to sediments, an index of diatom productivity in the bay, as well as its variability, were relatively low before European settlement of the Chesapeake Bay watershed. In the succeeding 300–400 yr, the flux of biogenic silica has increased by a factor of 4 to 5. Biogenic silica fluxes still appear to be increasing, despite recent nutrient-reduction efforts. The increase in diatom-produced biogenic silica has been partly masked (in concentration terms) by a similar increase in total sediment flux. This history suggests the magnitude of anthropogenic disturbance of the estuary and indicates that significant changes had occurred long before the twentieth century.

Antropogenically induced changes in sediment and biogenic silica fluxes in Chesapeake Bay

USGS Publications Warehouse

Colman, Steven M.; Bratton, J.F.

2003-01-01

Sediment cores as long as 20 m, dated by 14C, 210Pb, and 137Cs methods and pollen stratigraphy, provide a history of diatom productivity and sediment-accumulation rates in Chesapeake Bay. We calculated the flux of biogenic silica and total sediment for the past 1500 yr for two high-sedimentation-rate sites in the mesohaline section of the bay. The data show that biogenic silica flux to sediments, an index of diatom productivity in the bay, as well as its variability, were relatively low before European settlement of the Chesapeake Bay watershed. In the succeeding 300-400 yr, the flux of biogenic silica has increased by a factor of 4 to 5. Biogenic silica fluxes still appear to be increasing, despite recent nutrient-reduction efforts. The increase in diatom-produced biogenic silica has been partly masked (in concentration terms) by a similar increase in total sediment flux. This history suggests the magnitude of anthropogenic disturbance of the estuary and indicates that significant changes had occurred long before the twentieth century.

Historical trace element distribution in sediments from the Mississippi River delta

USGS Publications Warehouse

Swarzenski, P.W.; Baskaran, M.; Rosenbauer, R.J.; Orem, W.H.

2006-01-01

Five sediment cores were collected on the shelf of the inner Mississippi Bight in June 2003 for a suite of radionuclides to establish geochronologies and trace elements to examine patterns of contaminant deposition and accumulation. Core sites were chosen to reflect a matrix of variable water depths, proximity to the Mississippi River mouth as the primary source for terrigenous particles, and extent and duration of summertime water column hypoxia. The vertical distribution of 239,240Pu and 210Pbxs (= 210Pbtotal - 226Ra) provided reliable geochronological age constraints to develop models for mass accumulation rates and historic trace element inputs and variations. Mass accumulation rates ranged from 0.27 to 0.87 g cm-2 yr-1 and were internally consistent using either 210Pbxs or 239,240Pu. Measured inventories of 137Cs, 239,240Pu, and 210Pbxs were compared to atmospheric deposition rates to quantify potential sediment focusing or winnowing. Observed variability in calculated mass accumulation rates may be attributed foremost to site-specific proximity to the river mouth (i.e., sediment source), variability in water depth, and enhanced sediment focusing at the Mississippi River canyon site. Trace element concentrations were first normalized to Al, and then Al-normalized enrichment factors (ANEF) were calculated based on preanthropogenic and crustal trace element abundances. These ANEFs were typically > 1 for V and Ba, while for most other elements studied, either no enrichment or depletion was observed. The enrichment of Ba may be related, in part, to the seasonal occurrence of oxygen-depleted subsurface waters off the Mississippi River delta, as well as being an ubiquitous by-product of the petroleum industry. ?? 2006 Estuarine Research Federation.

Monsoonal vs. glacial control on erosion and sediment storage in the Himalayan rain shadow, Zanskar River, northwest India

NASA Astrophysics Data System (ADS)

Jonell, Tara; Clift, Peter; Carter, Andrew; Böning, Philipp; Wittmann, Hella

2016-04-01

Summer monsoon precipitation strongly controls erosion and sediment storage in the frontal Himalaya but the relationship between monsoonal variability and erosion is less well-constrained beyond the High Himalayan topographic divide in the rain shadow. Here we establish a Quaternary erosional history for a rain shadow tributary of the upper Indus River system, the Zanskar River, by applying several sediment provenance techniques to modern and dated terrace river sediments. We evaluate if there are temporal links between sediment storage and moisture supply to the rain shadow and if regions like the Zanskar River basin play a significant role in controlling total sediment flux to the Indus River. We compile bulk sediment petrography and Sr and Nd isotope geochemistry, detrital U-Pb zircon and apatite fission track dating with in-situ 10Be cosmogenic radionuclide techniques to identify patterns of erosion and sediment production across Zanskar. Bulk petrography, Sr and Nd isotope geochemistry, and U-Pb detrital zircon spectra of modern and older terrace sediments indicate high rates of erosion along the Greater Himalaya in the Zanskar River basin. We find that the wettest and most glaciated subcatchment dominates the bulk sediment provenance signal, with only moderate input from other tributaries, and that other basin parameters cannot explain our observations. Catchment-averaged in-situ 10Be cosmogenic nuclide concentrations of modern sediments indicate erosion rates up to ˜1.2 mm y-1 but show strong dilution attributed to glacial sediment recycling into the modern river, suggesting rates nearer 0.4-0.6 mm•y-1. These rates are consistent with longer-term rates of incision (0.3-0.7 mm•y-1) calculated from detrital apatite fission track ages, and incision rates inferred from Late Glacial and Holocene terraces near the Zanskar-Indus confluence. Our findings suggest that sediment production in glaciated Himalayan rain shadow environments like Zanskar is largely controlled by internal glacial fluctuations coupled with periodic dissection and reworking of terrace material during strong monsoonal precipitation phases.

Modeling of air pollution from the power plant ash dumps

NASA Astrophysics Data System (ADS)

Aleksic, Nenad M.; Balać, Nedeljko

A simple model of air pollution from power plant ash dumps is presented, with emission rates calculated from the Bagnold formula and transport simulated by the ATDL type model. Moisture effects are accounted for by assumption that there is no pollution on rain days. Annual mean daily sedimentation rates, calculated for the area around the 'Nikola Tesla' power plants near Belgrade for 1987, show reasonably good agreement with observations.

Integrative neural networks model for prediction of sediment rating curve parameters for ungauged basins

NASA Astrophysics Data System (ADS)

Atieh, M.; Mehltretter, S. L.; Gharabaghi, B.; Rudra, R.

2015-12-01

One of the most uncertain modeling tasks in hydrology is the prediction of ungauged stream sediment load and concentration statistics. This study presents integrated artificial neural networks (ANN) models for prediction of sediment rating curve parameters (rating curve coefficient α and rating curve exponent β) for ungauged basins. The ANN models integrate a comprehensive list of input parameters to improve the accuracy achieved; the input parameters used include: soil, land use, topographic, climatic, and hydrometric data sets. The ANN models were trained on the randomly selected 2/3 of the dataset of 94 gauged streams in Ontario, Canada and validated on the remaining 1/3. The developed models have high correlation coefficients of 0.92 and 0.86 for α and β, respectively. The ANN model for the rating coefficient α is directly proportional to rainfall erosivity factor, soil erodibility factor, and apportionment entropy disorder index, whereas it is inversely proportional to vegetation cover and mean annual snowfall. The ANN model for the rating exponent β is directly proportional to mean annual precipitation, the apportionment entropy disorder index, main channel slope, standard deviation of daily discharge, and inversely proportional to the fraction of basin area covered by wetlands and swamps. Sediment rating curves are essential tools for the calculation of sediment load, concentration-duration curve (CDC), and concentration-duration-frequency (CDF) analysis for more accurate assessment of water quality for ungauged basins.

Effective Discharge and Annual Sediment Yield on Brazos River

NASA Astrophysics Data System (ADS)

Rouhnia, M.; Salehi, M.; Keyvani, A.; Ma, F.; Strom, K. B.; Raphelt, N.

2012-12-01

Geometry of an alluvial river alters dynamically over the time due to the sediment mobilization on the banks and bottom of the river channel in various flow rates. Many researchers tried to define a single representative discharge for these morphological processes such as "bank-full discharge", "effective discharge" and "channel forming discharge". Effective discharge is the flow rate in which, the most sediment load is being carried by water, in a long term period. This project is aimed to develop effective discharge estimates for six gaging stations along the Brazos River from Waco, TX to Rosharon, TX. The project was performed with cooperation of the In-stream Flow Team of the Texas Water Development Board (TWDB). Project objectives are listed as: 1) developing "Flow Duration Curves" for six stations based on mean-daily discharge by downloading the required, additional data from U.S Geological Survey website, 2) developing "Rating Curves" for six gaging stations after sampling and field measurements in three different flow conditions, 3) developing a smooth shaped "Sediment Yield Histogram" with a well distinguished peak as effective discharge. The effective discharge was calculated using two methods of manually and automatic bin selection. The automatic method is based on kernel density approximation. Cross-sectional geometry measurements, particle size distributions and water field samples were processed in the laboratory to obtain the suspended sediment concentration associated with flow rate. Rating curves showed acceptable trends, as the greater flow rate we experienced, the more sediment were carried by water.

Mapping Spatial Distributions of Stream Power and Channel Change along a Gravel-Bed River in Northern Yellowstone

NASA Astrophysics Data System (ADS)

Lea, D. M.; Legleiter, C. J.

2014-12-01

Stream power represents the rate of energy expenditure along a river and can be calculated using topographic data acquired via remote sensing. This study used remotely sensed data and field measurements to quantitatively relate temporal changes in the form of Soda Butte Creek, a gravel-bed river in northeastern Yellowstone National Park, to stream power gradients along an 8 km reach. Aerial photographs from 1994-2012 and cross-section surveys were used to assess lateral channel mobility and develop a morphologic sediment budget for quantifying net sediment flux for a series of budget cells. A drainage area-to-discharge relationship and digital elevation model (DEM) developed from LiDAR data were used to obtain the discharge and slope values, respectively, needed to calculate stream power. Local and lagged relationships between mean stream power gradient at median peak discharge and volumes of erosion, deposition, and net sediment flux were quantified via spatial cross-correlation analyses. Similarly, autocorrelations of locational probabilities and sediment fluxes were used to examine spatial patterns of channel mobility and sediment transfer. Energy expended above critical stream power was calculated for each time period to relate the magnitude and duration of peak flows to the total volume of sediment eroded or deposited during each time increment. Our results indicated a lack of strong correlation between stream power gradients and sediment flux, which we attributed to the geomorphic complexity of the Soda Butte Creek watershed and the inability of our relatively simple statistical approach to link sediment dynamics expressed at a sub-budget cell scale to larger-scale driving forces such as stream power gradients. Future studies should compare the moderate spatial resolution techniques used in this study to very-high resolution data acquired from new fluvial remote sensing technologies to better understand the amount of error associated with stream power, sediment transport, and channel change calculated from historical datasets.

Toxicity and bioaccumulation of a mixture of heavy metals in Chironomus tentans (Diptera: Chironomidae) in synthetic sediment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrahy, E.A.; Clements, W.H.

1997-02-01

This research investigated toxicity and bioaccumulation of a mixture of Cd, Cu, Pb, and Zn in Chironomus tentans in synthetic sediment, and compared predicted to measured steady-state bioaccumulation factors (BAFs). In a toxicity test, C. tentans were exposed to various dilutions of a base concentration (1.0 X) of a mixture of the four metals (5 {micro}g/g Cd. 10 {micro}g/g Cu. 70 {micro}g/g Pb, and 300 {micro}g/g Zn) in synthetic sediment. Mortality ranged from 17 to 100%. To measure bioaccumulation of the metals, C. tentans were exposed to 0.35 X the base concentration for a period of up to 14 dmore » in two uptake tests. Bioaccumulation of all four metals increased over the 14-d uptake phases. Concentrations of metals in chironomids were significantly correlated with exposure time in the uptake phases. Only concentrations of copper approached background levels after 7 d depuration. Uptake rate coefficients and elimination rate constants were determined for each metal. Bioaccumulation factors were highest for Cd and lowest for Pb. With the exception of Pb, steady-state BAFs were within a factor of about two of those calculated using the first-order kinetic model. The high BAFs calculated may indicate greater bioavailability in synthetic sediment. Studies comparing toxicity and bioaccumulation of natural and synthetic sediments are necessary before the use of synthetic sediments is widely adopted.« less

A method for the calculation of anaerobic oxidation of methane rates across regional scales: an example from the Belt Seas and The Sound (North Sea-Baltic Sea transition)

NASA Astrophysics Data System (ADS)

Mogollón, José M.; Dale, Andrew W.; Jensen, Jørn B.; Schlüter, Michael; Regnier, Pierre

2013-08-01

Estimating the amount of methane in the seafloor globally as well as the flux of methane from sediments toward the ocean-atmosphere system are important considerations in both geological and climate sciences. Nevertheless, global estimates of methane inventories and rates of methane production and consumption through anaerobic oxidation in marine sediments are very poorly constrained. Tools for regionally assessing methane formation and consumption rates would greatly increase our understanding of the spatial heterogeneity of the methane cycle as well as help constrain the global methane budget. In this article, an algorithm for calculating methane consumption rates in the inner shelf is applied to the gas-rich sediments of the Belt Seas and The Sound (North Sea-Baltic Sea transition). It is based on the depth of free gas determined by hydroacoustic techniques and the local methane solubility concentration. Due to the continuous nature of shipboard hydroacoustic measurements, this algorithm captures spatial heterogeneities in methane fluxes better than geochemical analyses of point sources such as observational/sampling stations. The sensibility of the algorithm with respect to the resolution of the free gas depth measurements (2 m vs. 50 cm) is proven of minor importance (a discrepancy of <10%) for a small part of the study area. The algorithm-derived anaerobic methane oxidation rates compare well with previous measured and modeling studies. Finally, regional results reveal that contemporary anaerobic methane oxidation in worldwide inner-shelf sediments may be an order of magnitude lower (ca. 0.24 Tmol year-1) than previous estimates (4.6 Tmol year-1). These algorithms ultimately help improve regional estimates of anaerobic oxidation of methane rates.

Rates and extent of microbial debromination in the deep subseafloor biosphere

NASA Astrophysics Data System (ADS)

Berg, R. D.; Solomon, E. A.; Morris, R. M.

2013-12-01

Recent genomic and porewater geochemical data suggest that reductive dehalogenation of a wide range of halogenated organic compounds could represent an important energy source for deep subseafloor microbial communities. At continental slope sites worldwide, there is a remarkably linear relationship between porewater profiles of ammonium and bromide, indicating that the factors controlling the distribution and rates of dehalogenation have the potential to influence carbon and nitrogen cycling in the deep subsurface biosphere. Though this metabolic pathway could play an important role in the cycling of otherwise refractory pools of carbon and nitrogen in marine sediments and provide energy to microbial communities in the deep subsurface biosphere, the rates and extent of dehalogenation in marine sediments are poorly constrained. Here we report net reaction rate profiles of debromination activity in continental slope sediments, calculated from numerical modeling of porewater bromide profiles from several margins worldwide. The reaction rate profiles indicate three common zones of debromination activity in slope sediments: 1) low rates of debromination, and a potential bromine sink, in the upper sediment column correlating to the sulfate reduction zone, with net bromide removal rates from -3.6 x 10^-2 to -4.85 x 10^-1 μmol m^-2 yr^-1, 2) high rates of debromination from the sulfate-methane transition zone to ~40-100 mbsf, with net bromide release rates between 7.1 x 10^-2 to 3.9 x 10^-1 μmol m^-2 yr^-1, and 3) an inflection point at ~40-100 mbsf, below which net rates of debromination decrease by an order of magnitude and at several sites are indistinguishable from zero. These results indicate that dehalogenating activity is widely distributed in marine sediments, providing energy to fuel deep subseafloor microbial communities, with potentially important consequences for the global bromine and nitrogen cycles.

The numerical calculation of hydrological processes in the coastal zone of the Black Sea region in the city of Poti

NASA Astrophysics Data System (ADS)

Saghinadze, Ivane; Pkhakadze, Manana

2016-04-01

(The article was published with support of the Sh. Rustaveli National Science Foundation) The serious environmental problems started in Poti after transfer of the main flow of the river Rioni to the north. As a result the flooding of the city stopped, but the reduction of water consumption in the city channel, caused a decrease of the sediments carried away by the river, what leads to coastal erosion. The coast changes are connected with the movement of the waves and currents in the coastal part of the sea. In the paper, the three-dimensional mathematical model of sediment transport and coastal zone lithodynamics is developed. The finite element formulations for the problems of wave modes, coastal currents, sediment transport and evolution of the coastal zone of the sea, are given. The numerical algorithms, implemented in the form of software. Programs are allowing to bring the solutions of the tasks to numerical results. The numerical modeling was developed in three stages. In the first stage the topography of the coast and the initial geometry of the structures are considered as an input parameters. Then, coastal wave field is calculated for the conditions prescribed in the initial wave. In the second stage, the calculated wave field is used to estimate the spatial distribution of the radiation stresses near-bottom orbital velocity. In the third stage the coastal wave fields and flow fields are used in the sub-models of sediment transport and changes in the topography of the coast. In the numerical solution of basic equations of motion of the waves, coastal currents and changes in sea bottom topography we use: finite element, finite difference methods and the method of upper relaxation, Crank-Nicolson scheme. As an example, we are giving the results of research of the wave regime in the coastal area of the city of Poti (700X600m) adjacent to the port of Poti. The bottom profile, in this area is rather complicated. During the calculations of the average rise of sea level, 0.1m was taken as the initial value, which corresponds to the actual conditions The calculations have found that in the excitement, the sediment transport rates at a depth of 10-15m are almost zero. The maximum value of the velocity of sediment transport change within 0.006-0.0065m2/s.In the case of the western waves it is essential for longshore sediment transport directions, which varies in the range 0.0015-0.0022m2/s. The rate of sediment transport perpendicular to the bank in this case is irrelevant, and their maximum values in the range 0.00001-0.000017m2/s. Changes in the water depth varies from -0.25 to 0.29m. The rate of coastal erosion south of the port of 8-10 m/year.

Global Ocean Sedimentation Patterns: Plate Tectonic History Versus Climate Change

NASA Astrophysics Data System (ADS)

Goswami, A.; Reynolds, E.; Olson, P.; Hinnov, L. A.; Gnanadesikan, A.

2014-12-01

Global sediment data (Whittaker et al., 2013) and carbonate content data (Archer, 1996) allows examination of ocean sedimentation evolution with respect to age of the underlying ocean crust (Müller et al., 2008). From these data, we construct time series of ocean sediment thickness and carbonate deposition rate for the Atlantic, Pacific, and Indian ocean basins for the past 120 Ma. These time series are unique to each basin and reflect an integrated response to plate tectonics and climate change. The goal is to parameterize ocean sedimentation tied to crustal age for paleoclimate studies. For each basin, total sediment thickness and carbonate deposition rate from 0.1 x 0.1 degree cells are binned according to basement crustal age; area-corrected moments (mean, variance, etc.) are calculated for each bin. Segmented linear fits identify trends in present-day carbonate deposition rates and changes in ocean sedimentation from 0 to 120 Ma. In the North and South Atlantic and Indian oceans, mean sediment thickness versus crustal age is well represented by three linear segments, with the slope of each segment increasing with increasing crustal age. However, the transition age between linear segments varies among the three basins. In contrast, mean sediment thickness in the North and South Pacific oceans are numerically smaller and well represented by two linear segments with slopes that decrease with increasing crustal age. These opposing trends are more consistent with the plate tectonic history of each basin being the controlling factor in sedimentation rates, rather than climate change. Unlike total sediment thickness, carbonate deposition rates decrease smoothly with crustal age in all basins, with the primary controls being ocean chemistry and water column depth.References: Archer, D., 1996, Global Biogeochem. Cycles 10, 159-174.Müller, R.D., et al., 2008, Science, 319, 1357-1362.Whittaker, J., et al., 2013, Geochem., Geophys., Geosyst. DOI: 10.1002/ggge.20181

EFFECTS OF NITROGEN LOADING, FRESHWATER RESIDENCE TIME, AND INTERNAL LOSSES ON NITROGEN CONCENTRATIONS IN ESTUARIES

EPA Science Inventory

A simple model is presented that uses the annual loading rate of total nitrogen (TN) and the water residence time to calculate: 1) average annual TN concentration and intemalloss rates (e.g. denitrification and incorporation in sediments) in an estuary, and 2) the rate of nitroge...

Two-dimensional simulation of clastic and carbonate sedimentation, consolidation, subsidence, fluid flow, heat flow and solute transport during the formation of sedimentary basins

NASA Astrophysics Data System (ADS)

Bitzer, Klaus

1999-05-01

Geological processes that create sedimentary basins or act during their formation can be simulated using the public domain computer code `BASIN'. For a given set of geological initial and boundary conditions the sedimentary basin evolution is calculated in a forward modeling approach. The basin is represented in a two-dimensional vertical cross section with individual layers. The stratigraphic, tectonic, hydrodynamic and thermal evolution is calculated beginning at an initial state, and subsequent changes of basin geometry are calculated from sedimentation rates, compaction and pore fluid mobilization, isostatic compensation, fault movement and subsidence. The sedimentologic, hydraulic and thermal parameters are stored at discrete time steps allowing the temporal evolution of the basin to be analyzed. A maximum flexibility in terms of geological conditions is achieved by using individual program modules representing geological processes which can be switched on and off depending on the data available for a specific simulation experiment. The code incorporates a module for clastic and carbonate sedimentation, taking into account the impact of clastic sediment supply on carbonate production. A maximum of four different sediment types, which may be mixed during sedimentation, can be defined. Compaction and fluid flow are coupled through the consolidation equation and the nonlinear form of the equation of state for porosity, allowing nonequilibrium compaction and overpressuring to be calculated. Instead of empirical porosity-effective stress equations, a physically consistent consolidation model is applied which incorporates a porosity dependent sediment compressibility. Transient solute transport and heat flow are calculated as well, applying calculated fluid flow rates from the hydraulic model. As a measure for hydrocarbon generation, the Time-Temperature Index (TTI) is calculated. Three postprocessing programs are available to provide graphic output in PostScript format: BASINVIEW is used to display the distribution of parameters in the simulated cross-section of the basin for defined time steps. It is used in conjunction with the Ghostview software, which is freeware and available on most computer systems. AIBASIN provides PostScript output for Adobe Illustrator®, taking advantage of the layer-concept which facilitates further graphic manipulation. BASELINE is used to display parameter distribution at a defined well or to visualize the temporal evolution of individual elements located in the simulated sedimentary basin. The modular structure of the BASIN code allows additional processes to be included. A module to simulate reactive transport and diagenetic reactions is planned for future versions. The program has been applied to existing sedimentary basins, and it has also shown a high potential for classroom instruction, giving the possibility to create hypothetical basins and to interpret basin evolution in terms of sequence stratigraphy or petroleum potential.

Water volume and sediment volume and density in Lake Linganore between Boyers Mill Road Bridge and Bens Branch, Frederick County, Maryland, 2012

USGS Publications Warehouse

Sekellick, Andrew J.; Banks, William S.L.; Myers, Michael K.

2013-01-01

To assist in understanding sediment loadings and the management of water resources, a bathymetric survey was conducted in the part of Lake Linganore between Boyers Mill Road Bridge and Bens Branch in Frederick County, Maryland. The bathymetric survey was performed in January 2012 by the U.S. Geological Survey, in cooperation with the City of Frederick and Frederick County. A separate, but related, field effort to collect 18 sediment cores was conducted in March and April 2012. Depth and location data from the bathymetric survey and location data for the sediment cores were compiled and edited by using geographic information system (GIS) software. A three-dimensional triangulated irregular network (TIN) model of the lake bottom was created to calculate the volume of stored water in the reservoir. Large-scale topographic maps of the valley prior to inundation in 1972 were provided by the Frederick County Division of Utilities and Solid Waste Management and digitized for comparison with current (2012) conditions in order to calculate sediment volume. Cartographic representations of both water depth and sediment accumulation were produced, along with an accuracy assessment for the resulting bathymetric model. Vertical accuracies at the 95-percent confidence level for the collected data, the bathymetric surface model, and the bathymetric contour map were calculated to be 0.64 feet (ft), 1.77 ft, and 2.30 ft, respectively. A dry bulk sediment density was calculated for each of the 18 sediment cores collected during March and April 2012, and used to determine accumulated sediment mass. Water-storage capacity in the study area is 110 acre-feet (acre-ft) at a full-pool elevation 308 ft above the National Geodetic Vertical Datum of 1929, whereas total sediment volume in the study area is 202 acre-ft. These totals indicate a loss of about 65 percent of the original water-storage capacity in the 40 years since dam construction. This corresponds to an average rate of sediment accumulation of 5.1 acre-ft per year since Linganore Creek was impounded. Sediment thicknesses ranged from 0 to 16.7 ft. Sediment densities ranged from 0.38 to 1.08 grams per cubic centimeter, and generally decreased in the downstream direction. The total accumulated-sediment mass was 156,000 metric tons between 1972 and 2012.

Sedimentation, bioturbation, and sedimentary fabric evolution on a modern mesotidal mudflat: A multi-tracer study of processes, rates, and scales

NASA Astrophysics Data System (ADS)

Bentley, Samuel J.; Swales, Andrew; Pyenson, Benjamin; Dawe, Justin

2014-03-01

A study of muddy tidal-flat sedimentation and bioturbation was undertaken in the Waitetuna Arm of Raglan Harbor, New Zealand, to evaluate the physical and biological processes that control cycling of sediment between the intertidal seabed and sediment-water interface, and also the formation of tidal flat sedimentary fabric and fine-scale stratigraphy. Cores were collected along an intertidal transect, and analyzed for sedimentary fabric, 210Pb and 7Be radiochemical distributions, and grain size. At the same locations, a new approach for time-series core-X-radiography study was undertaken (spanning 191 days), using magnetite-rich sand as a tracer for sedimentation and bioturbation processes in shallow tidal flat sediments. Sedimentary fabric consists of a shallow stratified layer overlying a deeper zone of intensely bioturbated shelly mud. Bioadvection mixes the deeper zone and contributes fine sediment to the surface stratified layer, via biodeposition. Physical resuspension and deposition of surface muds by wave and tidal flow are also likely contributors to formation of the surficial stratified layer, but physical stratification is not observed below this depth. The deliberate tracer study allowed calculation of bioadvection rates that control strata formation, and can be used to model diagenetic processes. Results suggest that the upper ˜15 cm of seabed can be fully mixed over timescales <1.75 y. Such mixing will erase pre-existing sedimentary fabric and transport buried sediment and chemical compounds back to the tidal-flat surface. Shallow biodiffusion also exists, but produces much slower and shallower mass transport. Best fits for 210Pb profiles using a diagenetic bioadvection/sedimentation model and independently measured tiered bioadvection rates suggest that sediment accumulation rates (SARs) on the tidal flat are ˜0.25 cm/y, near the low end of contemporary New Zealand muddy intertidal SARs. Frequent deposition and erosion of the surface layer demonstrates that long-term sediment accumulation captures only a small fraction of sediment deposited at any one time. Model results also suggest that our magnetite tracer method may slightly underestimate short-term shallow mixing rates (demonstrated by 7Be profiles), and slightly overestimate longer-term, deeper bioturbation rates (demonstrated by 210Pb profiles).

Development and Application of a Cohesive Sediment Transport Model in Coastal Louisiana

NASA Astrophysics Data System (ADS)

Sorourian, S.; Nistor, I.

2017-12-01

The Louisiana coast has suffered from rapid land loss due to the combined effects of increasing the rate of eustatic sea level rise, insufficient riverine sediment input and subsidence. The sediment in this region is dominated by cohesive sediments (up to 80% of clay). This study presents a new model for calculating suspended sediment concentration (SSC) of cohesive sediments. Several new concepts are incorporated into the proposed model, which is capable of estimating the spatial and temporal variation in the concentration of cohesive sediment. First, the model incorporates the effect of electrochemical forces between cohesive sediment particles. Second, the wave friction factor is expressed in terms of the median particle size diameter in order to enhance the accuracy of the estimation of bed shear stress. Third, the erosion rate of cohesive sediments is also expressed in time-dependent form. Simulated SSC profiles are compared with field data collected from Vermilion Bay, Louisiana. The results of the proposed model agree well with the experimental data, as soon as steady state condition is achieved. The results of the new numerical models provide a better estimation of the suspended sediment concentration profile compared to the initial model developed by Mehta and Li, 2003. Among the proposed developments, the formulation of a time-dependent erosion rate shows the most accurate results. Coupling of present model with the Finite-Volume, primitive equation Community Ocean Model (FVCOM) would shed light on the fate of fine-grained sediments in order to increase overall retention and restoration of the Louisiana coastal plain.

Processes and rates of sediment and wood accumulation in headwater streams of the Oregon Coast Range, USA

USGS Publications Warehouse

May, Christine L.; Gresswell, Robert E.

2003-01-01

Channels that have been scoured to bedrock by debris flows provide unique opportunities to calculate the rate of sediment and wood accumulation in low-order streams, to understand the temporal succession of channel morphology following disturbance, and to make inferences about processes associated with input and transport of sediment. Dendrochronology was used to estimate the time since the previous debris flow and the time since the last stand-replacement fire in unlogged basins in the central Coast Range of Oregon. Debris flow activity increased 42 per cent above the background rate in the decades immediately following the last wildfire. Changes in wood and sediment storage were quantified for 13 streams that ranged from 4 to 144 years since the previous debris flow. The volume of wood and sediment in the channel, and the length of channel with exposed bedrock, were strongly correlated with the time since the previous debris flow. Wood increased the storage capacity of the channel and trapped the majority of the sediment in these steep headwater streams. In the absence of wood, channels that have been scoured to bedrock by a debris flow may lack the capacity to store sediment and could persist in a bedrock state for an extended period of time. With an adequate supply of wood, low-order channels have the potential of storing large volumes of sediment in the interval between debris flows and can function as one of the dominant storage reservoirs for sediment in mountainous terrain.

Biogeochemical mercury methylation influenced by reservoir eutrophication, Salmon Falls Creek Reservoir, Idaho, USA

USGS Publications Warehouse

Gray, J.E.; Hines, M.E.

2009-01-01

Salmon Falls Creek Reservoir (SFCR) in southern Idaho has been under a mercury (Hg) advisory since 2001 as fish in this reservoir contain elevated concentrations of Hg. Concentrations of total Hg (HgT) and methyl-Hg (MeHg) were measured in reservoir water, bottom sediment, and porewater to examine processes of Hg methylation at the sediment/water interface in this reservoir. Rates of Hg methylation and MeHg demethylation were also measured in reservoir bottom sediment using isotopic tracer techniques to further evaluate methylation of Hg in SFCR. The highest concentrations for HgT and MeHg in sediment were generally found at the sediment/water interface, and HgT and MeHg concentrations declined with depth. Porewater extracted from bottom sediment contained highly elevated concentrations of HgT ranging from 11-230??ng/L and MeHg ranging from 0.68-8.5??ng/L. Mercury methylation was active at all sites studied. Methylation rate experiments carried out on sediment from the sediment/water interface show high rates of Hg methylation ranging from 2.3-17%/day, which is significantly higher than those reported in other Hg contaminant studies. Using porewater MeHg concentrations, we calculated an upward diffusive MeHg flux of 197??g/year for the entire reservoir. This sediment derived MeHg is delivered to the overlying SFCR water column, and eventually transferred to biota, such as fish. This study indicates that methylation of Hg is highly influenced by the hypolimnetic and eutrophic conditions in SFCR.

A comparative study of accumulation rates derived by He and Th isotope analysis of marine sediments

NASA Astrophysics Data System (ADS)

Marcantonio, Franco; Kumar, Niraj; Stute, Martin; Anderson, Robert F.; Seidl, Michele A.; Schlosser, Peter; Mix, Alan

1995-07-01

We present a detailed down-core analysis of helium isotope ratios and concentrations for bulk sediments from the central Equatorial Pacific that span the last two glacial-interglacial cycles. Measured 3He/4He ratios range from 1.0 × 10 -5 to 2.1 × 10 -4, or 7.4 to 149 times the atmospheric ratio. The 3He from interplanetary dust particles (IDPs) constitutes virtually all of the 3He measured within the sediment. Because carbonate accumulation rates are high in the Equatorial Pacific, the measured 3He concentrations are lower than have been measured elsewhere, and range from 4.7 × 10 -13 to 3.0 × 10 -12 cm 3STP · g -1. If the cosmic dust 3He-flux is constant with time, sediment mass accumulation rates can be determined from the 3He concentration in sediments. The excess 230Th technique is an entirely independent method for calculating sediment mass accumulation rates because its source is in-situ decay of 234U in seawater. To first order, initial excess 230Th activities correlate with 3He concentrations within this core. Based on the 230Th results, we estimate the 3He-flux to the Earth's surface as (9.6 ± 2.0) × 10 -16 cm 3STP · cm -2 · a -1. If this flux has remained constant over extended periods of time, it can be used to determine sediment accumulation rates beyond the 230Th range (300,000 yr).

Can Wet Rocky Granular Flows Become Debris Flows Due to Fine Sediment Production by Abrasion?

NASA Astrophysics Data System (ADS)

Arabnia, O.; Sklar, L. S.; Bianchi, G.; Mclaughlin, M. K.

2015-12-01

Debris flows are rapid mass movements in which elevated pore pressures are sustained by a viscous fluid matrix with high concentrations of fine sediments. Debris flows may form from coarse-grained wet granular flows as fine sediments are entrained from hillslope and channel material. Here we investigate whether abrasion of the rocks within a granular flow can produce sufficient fine sediments to create debris flows. To test this hypothesis experimentally, we used a set of 4 rotating drums ranging from 0.2 to 4.0 m diameter. Each drum has vanes along the boundary ensure shearing within the flow. Shear rate was varied by changing drum rotational velocity to maintain a constant Froude Number across drums. Initial runs used angular clasts of granodiorite with a tensile strength of 7.6 MPa, with well-sorted coarse particle size distributions linearly scaled with drum radius. The fluid was initially clear water, which rapidly acquired fine-grained wear products. After each 250 m tangential distance, we measured the particle size distributions, and then returned all water and sediment to the drums for subsequent runs. We calculate particle wear rates using statistics of size and mass distributions, and by fitting the Sternberg equation to the rate of mass loss from the size fraction > 2mm. Abundant fine sediments were produced in the experiments, but very little change in the median grain size was detected. This appears to be due to clast rounding, as evidenced by a decrease in the number of stable equilibrium resting points. We find that the growth in the fine sediment concentration in the fluid scales with unit drum power. This relationship can be used to estimate fine sediment production rates in the field. We explore this approach at Inyo Creek, a steep catchment in the Sierra Nevada, California. There, a significant debris flow occurred in July 2013, which originated as a coarse-grained wet granular flow. We use surveys to estimate flow depth and velocity where super-elevation occurred, to calculate a unit power of 4.5 KW/m2. From this we predict that 14% of the coarse mass is converted to fine sediment by abrasion per km. At that rate, the increase in fines concentration may have been sufficient to cause a wet granular flow to evolve into a debris flow within the first 1 km of its > 4km travel distance.

Experimental Investigations of the Weathering of Suspended Sediment by Alpine Glacial Meltwater

NASA Astrophysics Data System (ADS)

Brown, Giles H.; Tranter, M.; Sharp, M. J.

1996-04-01

The magnitude and processes of solute acquisition by dilute meltwater in contact with suspended sediment in the channelized component of the hydroglacial system have been investigated through a suite of controlled laboratory experiments. Constrained by field data from Haut Glacier d'Arolla, Valais, Switzerland the effects of the water to rock ratio, particle size, crushing, repeated wetting and the availability of protons on the rate of solute acquisition are demonstrated. These free-drift experiments suggest that the rock flour is extremely geochemically reactive and that dilute quickflow waters are certain to acquire solute from suspended sediment. These data have important implications for hydrological interpretations based on the solute content of glacial meltwater, mixing model calculations, geochemical denudation rates and solute provenance studies.

Agricultural land use doubled sediment yield of western China's rivers

NASA Astrophysics Data System (ADS)

Schmidt, A. H.; Bierman, P. R.; Sosa-Gonzalez, V.; Neilson, T. B.; Rood, D. H.; Martin, J.; Hill, M.

2017-12-01

Land use changes, such as deforestation and agriculture, increase soil erosion rates on the scale of hillslopes and small drainage basins; however, the effects of these changes on the sediment load in larger rivers is poorly quantified, with a few studies scattered globally, and only 10 data points in the world's most populous nation, China. At 20 different sites in western China, we compare contemporary (1945-1987) fluvial sediment yield data collected daily over 4 to 26 years (median = 19 years) to long-term measures of erosion (sediment generation) based on new isotopic measurements of in situ 10Be in river sediments. We find that median sediment transport at these sites exceeds background sediment generation rates by a factor of two (from 0.13 to 5.79 times, median 1.85 times) and that contemporary sediment yield is statistically significantly different from long-term sediment yield (p < 0.05). Agricultural land use is directly and significantly proportional to the ratio of contemporary sediment yield to long term sediment generation rates (Spearman correlation coefficient rho = 0.52, p < 0.05). We support these findings by calculating erosion indices (following Brown et al., 1988), which compare the delivery of meteoric 10Be to each watershed with the export of meteoric 10Be bound to riverine sediment. Erosion indices are also directly and significantly proportional to agricultural land use (rho = 0.58, p < 0.05). We measured unsupported 210Pb and 137Cs in 130 detrital samples from throughout the region. We find that only 4 samples (those from high elevation, low relief watersheds) have detectable 137Cs and 31 samples have detectable unsupported 210Pb. The lack of 137Cs in most samples suggests high rates of erosion in the 1950s-1960s when 137Cs would have been delivered to the landscape. Detectable 210Pb in 25% of the watersheds suggests that in some areas erosion rates have slowed since that time allowing 210Pb to accumulate to measurable levels. Together, these data sets demonstrate that upstream agricultural land use has significantly increased sediment supply to rivers in western China, likely increasing turbidity and decreasing ecosystem services such as fisheries.

Estimating the GIS-based soil loss and sediment delivery ratio to the sea for four major basins in South Korea.

PubMed

Lee, S E; Kang, S H

2013-01-01

This paper describes a sediment delivery ratio (SDR) using the Geographic Information System (GIS)-based Revised Universal Soil Loss Equation (RUSLE), to calculate the soil loss and sediment rating curve (SRC) basis of measured data in the six basins of Four Rivers, South Korea. The data set for calculating SDR was prepared during 3 years from 2008 to 2010. Mean soil loss in the six basins of Four Rivers was 515-869 t km(-2) yr(-1) and mean specific sediment yield (SSY) was 20-208 t km(-2) yr(-1) with basin size. The SDR ranged from 0.03 to 0.33 in the six rivers. Most sediment flows in the monsoon period from June to September (mean Max.: >97%; mean Min.: >84%), but SDR is lower than those of similar continental river basins. This is due to environmental factors, for example rainfall characteristics and associated run-off, soil characteristics and cultivated patterns with increasing basin size. This research provides the first application of SDR based on the observed field data in South Korea.

Particle mixing processes of Chernobyl fallout in deep Norwegian Sea sediments: Evidence for seasonal effects

NASA Astrophysics Data System (ADS)

Balzer, W.

1996-09-01

A 1430 m deep station in the Norwegian Sea (Voering Plateau) was occupied five times between May 1986 and February 1987 to investigate the seasonal variation in sediment mixing rates. Cherbnbyl-derived radiocesium, identified by its high proportion of short-lived 134Cs, was used as a tracer for mixing. Most of the nuclide input arrived at the sediment within a narrow time span in June/early July during the beginning of the seasonal biogenic sedimentation pulse. Measured 137Cs profiles in the sediment over time were compared with modelled distributions calculated with a finite difference scheme. The input function of radiocesium to the sea floor was evaluated from the increase of the total inventory with time. Time-invariant mixing coefficients did not provide reasonable fits to either summer or winter distributions. The best fit was obtained with a rate of mixing proportional to the radiocesium input flux, with an average enhancement factor of 6.6 during the two summer months. It appears that the benthic macrofauna are more active during the food supply season and rapidly ingest/bury freshly sedimented materials.

Distribution of radionuclides in the guano sediments of Xisha Islands, South China Sea and its implication.

PubMed

Xu, L Q; Liu, X D; Sun, L G; Yan, H; Liu, Y; Luo, Y H; Huang, J; Wang, Y H

2010-05-01

Several natural and anthropogenic radionuclides ((210)Pb, (226)Ra and (137)Cs) in guano-phosphatic coral sediments and pure guano particles collected from Ganquan, Guangjin, Jinqing and Jinyin Islands of the Xisha archipelago, South China Sea, were analyzed. The Constant Initial Concentration (CIC) model and the Constant Rate of Supply (CRS) model were applied for age calculation. The average supply rate of (210)Pb was 126 Bq m(-2) a(-1), very close to the flux of northern hemisphere average (125 Bq m(-2) a(-1)). The activities of anthropogenic radionuclides in the sediments were very low, indicating that human nuclear tests did not notably impact this region. The main source of radionuclides in the sediments was from atmospheric precipitation, and the organic matter derived from plant and produced by nutrient-rich guano could further enhance them. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Comparison between Measured and Calculated Sediment Transport Rates in North Fork Caspar Creek, California

NASA Astrophysics Data System (ADS)

Kim, T. W.; Yarnell, S. M.; Yager, E.; Leidman, S. Z.

2015-12-01

Caspar Creek is a gravel-bedded stream located in the Jackson Demonstration State Forest in the coast range of California. The Caspar Creek Experimental Watershed has been actively monitored and studied by the Pacific Southwest Research Station and California Department of Forestry and Fire Protection for over five decades. Although total annual sediment yield has been monitored through time, sediment transport during individual storm events is less certain. At a study site on North Fork Caspar Creek, cross-section averaged sediment flux was collected throughout two storm events in December 2014 and February 2015 to determine if two commonly used sediment transport equations—Meyer-Peter-Müller and Wilcock—approximated observed bedload transport. Cross-section averaged bedload samples were collected approximately every hour during each storm event using a Helley-Smith bedload sampler. Five-minute composite samples were collected at five equally spaced locations along a cross-section and then sieved to half-phi sizes to determine the grain size distribution. The measured sediment flux values varied widely throughout the storm hydrographs and were consistently less than two orders of magnitude in value in comparison to the calculated values. Armored bed conditions, changing hydraulic conditions during each storm and variable sediment supply may have contributed to the observed differences.

Sea-level changes and shelf break prograding sequences during the last 400 ka in the Aegean margins: Subsidence rates and palaeogeographic implications

NASA Astrophysics Data System (ADS)

Lykousis, V.

2009-09-01

The subsidence rates of the Aegean margins during the Middle-Upper Pleistocene were evaluated based on new and historical seismic profiling data. High-resolution seismic profiling (AirGun, Sparker and 3.5 kHz) have shown that (at least) four major oblique prograding sequences can be traced below the Aegean marginal slopes at increasing subbottom depths. These palaeo-shelf break glacial delta sediments have been developed during successive low sea-level stands (LST prograding sequences), suggesting continuous and gradual subsidence of the Aegean margins during the last 400 ka. Subsidence rates of the Aegean margins were calculated from the vertical displacement of successive topset-to-foreset transitions (palaeo-shelf break) of the LST prograding sediment sequences. The estimated subsidence rates that were calculated in the active boundaries of the Aegean microplate (North Aegean margins, Gulfs of Patras and Corinth) are high and range from 0.7 to 1.88 m ka -1, while the lowest values (0.34-0.60 m ka -1) are related to the low tectonic and seismic activity margins like the margin of Cyclades plateau. Lower subsidence rates (0.34-0.90 m ka -1) were estimated for the period 146-18 ka BP (oxygen isotopic stages 6-2) and higher (1.46-1.88 m ka -1) for the period from 425 to 250 ka BP (oxygen isotopic stages 12/10-8). A decrease of about 50% of the subduction rates in the Aegean margins was observed during the last 400 ka. During the isotopic stages 8, 10, 11 and 12, almost the 50-60% of the present Aegean Sea was land with extensive drainage systems and delta plains and large lakes in the central and North Aegean. Marine transgression in the North Aegean was rather occurred during the isotopic 9 interglacial period. The estimated palaeomorphology should imply fan delta development and sediment failures in the steep escarpments of the North Aegean margins and high sedimentation rates and turbidite sediment accumulation in the basins. It is deduced that the Black Sea was isolated from the Mediterranean during the Pleistocene prior oxygen isotopic stage 5.

Perspectives on geochemical proxies: The impact of model and parameter selection on the quantification of carbonate recrystallization rates

NASA Astrophysics Data System (ADS)

Huber, Christian; Druhan, Jennifer L.; Fantle, Matthew S.

2017-11-01

Diagenetic reactions in marine sediments, such as the recrystallization of carbonates, can impact the accuracy of paleo-environmental and paleo-climatic reconstructions by geochemical proxies. The extent to which the recrystallization of carbonates affects the chemistry of sedimentary archives depends on the reaction rate, extent of isotopic disequilibrium, and duration of reaction. The reaction rate, which is obviously critical, can be constrained by the elemental and isotopic compositions of pore fluids. Such constraints are affected by assumptions regarding the temperature in the sedimentary column relative to the temperature of formation, the burial rate, pore fluid advection, the composition of the sediments (carbonate-rich versus siliciclastic), and the porosity of the sediment column. In this study, we use a steady-state analytical solution to the diagenetic equations to constrain depth-dependent reaction rates (and extents of recrystallization) based on the Ca isotopic compositions of pore fluids in sedimentary columns at multiple ocean drilling sites (Sites 807, 984, 1170, and 1171), which encompass a diverse range of sedimentary compositions and conditions. We find that carbonates in siliciclastic sediments are generally less altered by diagenesis than their carbonate-rich counterparts. The discrepancy in recrystallization rates between siliciclastic and carbonate-rich sedimentary sections is, however, significantly smaller than previously estimated, suggesting that siliciclastic archives are not immune to diagenetic effects. While we find that diagenesis can decouple contemporaneous proxies of sea surface temperature (Mg/Ca and δ18O), our calculations also reveal that δ18O-based temperature estimates are more robust in siliciclastic sections relative to carbonate-rich sections. Sensitivity tests of the calculated extent of recrystallization suggest that uncertainties in porosity and burial rate are generally the greatest sources of error to proxy reconstruction from diagenetically altered sediments. The conclusions drawn using the analytical solution are benchmarked against a depth-dependent, forward numerical model using the CrunchFlow software (Steefel et al., 2015); ultimately, this comparison demonstrates that the assumptions necessary in deriving the analytical solutions have a relatively minor impact on the resulting conclusions.

Environmental Fate Studies of HMX Screening Studies. Phase 1

DTIC Science & Technology

1982-12-01

1,3,5,7-octahydro-l,3,5,7-tetranitrotetrazocirne, HMX, sorption and biosorption partition coefficients, photochemical rate constant, biotransformatLion...Holston River sediment was measured at 8.7. Based on an organic carbon con- tent of 1.3% in thc sediment, a K value of 670 was calculated. The biosorption ...27 Table 9 HMX Biosorption by Bacteria .............................. 39 ii -4 I: ’a LIST OF ILLUSTRATIONS

The diffusive boundary layer of sediments: oxygen microgradients over a microbial mat

NASA Technical Reports Server (NTRS)

Jorgensen, B. B.; Des Marais, D. J.

1990-01-01

Oxygen microelectrodes were used to analyze the distribution of the diffusive boundary layer (DBL) at the sediment-water interface in relation to surface topography and flow velocity. The sediment, collected from saline ponds, was covered by a microbial mat that had high oxygen consumption rate and well-defined surface structure. Diffusion through the DBL constituted an important rate limitation to the oxygen uptake of the sediment. The mean effective DBL thickness decreased from 0.59 to 0.16 mm as the flow velocity of the overlying water was increased from 0.3 to 7.7 cm s-1 (measured 1 cm above the mat). The oxygen uptake rate concurrently increased from 3.9 to 9.4 nmol cm-2 min-1. The effects of surface roughness and topography on the thickness and distribution of the DBL were studied by three-dimensional mapping of the sediment-water interface and the upper DBL boundary at 0.1-mm spatial resolution. The DBL boundary followed mat structures that had characteristic dimensions > 1/2 DBL thickness but the DBL had a dampened relief relative to the mat. The effective surface area of the sediment-water interface and of the upper DBL boundary were 31 and 14% larger, respectively, than a flat plane. Surface topography thereby increased the oxygen flux across the sediment-water interface by 49% relative to a one-dimensional diffusion flux calculated from the vertical oxygen microgradients.

Towards a novel look on low-frequency climate reconstructions

NASA Astrophysics Data System (ADS)

Kamenik, Christian; Goslar, Tomasz; Hicks, Sheila; Barnekow, Lena; Huusko, Antti

2010-05-01

Information on low-frequency (millennial to sub-centennial) climate change is often derived from sedimentary archives, such as peat profiles or lake sediments. Usually, these archives have non-annual and varying time resolution. Their dating is mainly based on radionuclides, which provide probabilistic age-depth relationships with complex error structures. Dating uncertainties impede the interpretation of sediment-based climate reconstructions. They complicate the calculation of time-dependent rates. In most cases, they make any calibration in time impossible. Sediment-based climate proxies are therefore often presented as a single, best-guess time series without proper calibration and error estimation. Errors along time and dating errors that propagate into the calculation of time-dependent rates are neglected. Our objective is to overcome the aforementioned limitations by using a 'swarm' or 'ensemble' of reconstructions instead of a single best-guess. The novelty of our approach is to take into account age-depth uncertainties by permuting through a large number of potential age-depth relationships of the archive of interest. For each individual permutation we can then calculate rates, calibrate proxies in time, and reconstruct the climate-state variable of interest. From the resulting swarm of reconstructions, we can derive realistic estimates of even complex error structures. The likelihood of reconstructions is visualized by a grid of two-dimensional kernels that take into account probabilities along time and the climate-state variable of interest simultaneously. For comparison and regional synthesis, likelihoods can be scored against other independent climate time series.

Historical sediment budget and present-day catchment-shoreline coupling at Twofold Bay, southeastern Australia

NASA Astrophysics Data System (ADS)

Tamura, T.; Oliver, T.; Hudson, J.; Woodroffe, C. D.

2017-12-01

Considering projected impacts of sea-level rise in the 21st century on sandy shorelines, an understanding of long-term sediment budget for individual beaches or coastal compartments supports assessments of shoreline stability. We examined a low-lying coastal beach-ridge barrier in Twofold Bay using optically stimulated luminescence (OSL) dating , airborne LiDAR, sedimentological analysis and seismic data to assess changes in rates of sediment supply to this shoreline through time. Calculations of barrier volume, Twofold Bay bay-floor sediment volume and estimates of sediment delivery from a proximal river system provide a broad-scale assessment of past-sediment budget. Between ca. 7500 years ago and 1500 years ago, sources of sediment for shoreline progradation at Boydtown were bay-floor sediments either inherited or moved into the embayment during late-stage transgression. Progradation rate between ca. 7500-1500 years ago was 0.16 m/yr with subaerial barrier volume accumulating at 0.46 m3/m/yr. Between ca. 1500 years and present day, the Towamba River to the south has delivered additional sediment to the Boydtown shoreline more than doubling shoreline progradation rate to 0.65 m/yr and subaerial barrier accumulation has risen to 1.83 m3/m/yr. The delivery of fluvial sediment from the Towamba River was restricted to the past ca. 1500 years as prior to this, estuary infilling prevented floods delivering sediments to the bay. This recent historical coupling of river sand supply and shoreline progradation rate implies that anthropogenic modifications to the Towamba River catchment such as river damming, or climatic changes reducing rainfall or runoff, would negatively impact the Boydtown Beach shoreline. Conversely increased rainfall or deforestation may increase sediment discharge due to upstream erosion. The Boydtown shoreline within Twofold Bay may be able to maintain its current position in the coming century if fluvial sediment delivery continues. The fact that other shorelines within Twofold Bay are seemingly unaffected by the Towamba River, and most shorelines in southeast Australia receive minimal fluvial sediment input, further emphasises the need to consider nearshore sediment reserves in order to accurately determine sea-level rise impacts on sandy shorelines.

Observations of Near-Bed Deposition and Resuspension Processes at the Fluvial-Tidal Transition Using High Resolution Adcp, Adv, and Lisst

NASA Astrophysics Data System (ADS)

Haught, D. R.; Stumpner, P.

2012-12-01

Processes that determine deposition and resuspension of sediment in fluvial and tidal systems are complicated and difficult to predict because of turbulence-sediment interaction. In fluvial systems net sediment deposition rates near the bed are determined by shear stresses that occur when turbulence interacts with the bed and the entrained sediment above. In tidal systems, processes are driven primarily by the confounding factors of slack water and reversing flow. In this study we investigate near-bed sediment fluxes, settling velocities and sediment size distributions during a change from a fluvial signal to a tidal signal. In order to examine these processes a high resolution, high frequency ADCP, ADV, water quality sonde and LISST data were collocated at the fluvial-tidal transition in the Sacramento River at Freeport, CA. Data were collected at 15-30 minute increments for a month`. Data were dissevered into fluvial and tidal components. Acoustic backscatterence was used as a surrogate to sediment concentration and sediment flux () was calculated from the turbulence properties. Settling velocities were computed from the diffusion-advection equation assuming equilibrium of settling and re-suspension fluxes. Particle density was back-calculated from median particle diameter and calculated settling velocities (Reynolds number<0.5) using Stokes' law. Preliminary results suggest that during peak fluvial discharge that the diffusion-advection gives poor estimates of settling velocities as inferred from particle densities above 3500 kg/m3. During the transition from fluvial to tidal signal and throughout the tidal signal particle densities range from 2650 kg/m3 to 1000 kg/m3, suggesting that settling velocities were accurately estimated. Thus the equilibrium assumption appears poor during high fluvial discharge and reasonable during low fluvial discharge when tidal signal is dominant.

Modern Sedimentation off the Kaoping River, SW Taiwan: A Comparison with Eel River's S2S System

NASA Astrophysics Data System (ADS)

Huh, C.; Lin, H.; Lin, S.

2006-12-01

The Kaoping (KP) River in SW Taiwan has a watershed area of 3257 km2 and an annual sediment discharge of 49 MT. Although the sediment yield of the KP River basin (1.5×104 ton km-2 yr^{- 1}) is the 4th highest among Taiwan's catchment basins, it is nearly one order of magnitude higher than that of the Eel River's basin (~1.8×103 ton km-2 yr-1; the highest in the U.S.). The KP canyon extends almost immediately seaward from the river's mouth and terminates in the northwestern corner of the South China Sea. The head of the canyon is characterized by high and steep walls exceeding 600 m. The KP river's source-to-sink system offers a dramatic case of mountainous rivers at active margins for S2S study. Here we report some results about modern sedimentation in KP river's dispersal system. Seventy-six sediment cores collected from an area of ~3000 km2 were analyzed for fallout nuclides 7Be, 137Cs and 210Pb by gamma spectrometry. From profiles of excess 210Pb and 137Cs sediment accumulation rates in the coring sites were estimated, which vary from 0.06 to 1.6 cm/yr, with the highest rates (>1 cm/yr) distributed in the upper slope (<600 m) on both sides of the KP canyon. The area with high sedimentation rates on Pb-210 time scale coincides with the area covered by a flood layer resulting from Typhoon Haitang during July 18-20, 2005. This suggests that the open margin on the upper slope is a depocenter for sediment dispersed via a surface component of the river's plume on various timescales (from events to centennial). With a total of 76 sampling points laid out, a framework consisting of 105 triangular grids is configured to calculate the budget of sediment in the study area. The calculated budget, at 7.2 MT/yr, accounts for only ~15% of KP river's sediment discharge. We speculate that most of the remainder is exported out of the study area via the KP canyon to the deep sea by gravity-driven turbidity or hyperpycnal flows.

The geochemistry of redox sensitive trace metals in sediments

NASA Astrophysics Data System (ADS)

Morford, Jennifer L.; Emerson, Steven

1999-06-01

We analyzed the redox sensitive elements V, Mo, U, Re and Cd in surface sediments from the Northwest African margin, the U.S. Northwest margin and the Arabian Sea to determine their response under a range of redox conditions. Where oxygen penetrates 1 cm or less into the sediments, Mo and V diffuse to the overlying water as Mn is reduced and remobilized. Authigenic enrichments of U, Re and Cd are evident under these redox conditions. With the onset of sulfate reduction, all of the metals accumulate authigenically with Re being by far the most enriched. General trends in authigenic metal accumulation are described by calculating authigenic fluxes for the 3 main redox regimes: oxic, reducing where oxygen penetrates ≤1 cm, and anoxic conditions. Using a simple diagenesis model and global estimates of organic carbon rain rate and bottom water oxygen concentrations, we calculate the area of sediments below 1000 m water depth in which oxygen penetration is ≤1 cm to be 4% of the ocean floor. We conclude that sediments where oxygen penetrates ≤1 cm release Mn, V and Mo to seawater at rates of 140%-260%, 60%-150% and 5%-10% of their respective riverine fluxes, using the authigenic metal concentrations and accumulation rates from this work and other literature. These sediments are sinks for Re, Cd and U, with burial fluxes of 70%-140%, 30%-80% and 20%-40%, respectively, of their dissolved riverine inputs. We modeled the sensitivity of the response of seawater Re, Cd and V concentrations to changes in the area of reducing sediments where oxygen penetrates ≤1 cm. Our analysis suggests a negligible change in seawater Re concentration, whereas seawater concentrations of Cd and V could have decreased and increased, respectively, by 5%-10% over 20 kyr if the area of reducing sediments increased by a factor of 2 and by 10%-20% if the area increased by a factor of 3. The concentration variations for a factor of 2 increase in the area of reducing sediments are at about the level of uncertainty of Cd/Ca and V/Ca ratios observed in foraminifera shells over the last 40 kyr. This implies that the area of reducing sediments in the ocean deeper than 1000 m (4%) has not been greater than twice the present value in the recent past.

The Effects of Urbanization and Flood Control on Sediment Discharge of a Southern California River, Evidence of a Dilution Effect

NASA Astrophysics Data System (ADS)

Warrick, J. A.; Orzech, K. M.; Rubin, D. M.

2004-12-01

The southern California landscape has undergone dramatic urbanization and population growth during the past 60 years and currently supports almost 20 million inhabitants. During this time, rivers of the region have been altered with damming, channel straightening and hardening, and water transfer engineering. These changes have drastically altered water and sediment discharge from most of the region's drainage basins. Here we focus on changes in sediment discharge from the largest watershed of southern California, the Santa Ana River. Order-of-magnitude drops in the suspended sediment rating curves (the relationship between suspended sediment concentration and instantaneous river discharge) are observed between 1967 and 2001, long after the construction of a major flood control dam in 1941. These sediment concentration decreases do not, however, represent alteration of the total sediment flux from the basin (a common interpretation of sediment rating curves), but rather a dilution of suspended sediment by increases (approx. 4x) in stormwater discharge associated with urbanization. Increases in peak and total stormwater discharge are consistent with runoff patterns from urbanizing landscapes, supporting our hypothesis that the diluting water originated from stormwater runoff generated in urban areas both up- and downstream of dams. Our dilution hypothesis is further supported with water and sediment budgets, dilution calculations, and suspended and bed grain size information.

Energetic constraints on life in deep marine sediments

NASA Astrophysics Data System (ADS)

Amend, J.; LaRowe, D.

2013-12-01

Microorganisms are abundant in deep-sea sediments, but what percentage of cells is active, how fast do they grow, and what factors control their diversity and population size? Geochemical modelling of redox reaction energetics can help in answering these questions. Calculations of Gibbs energies reveal which reactions are thermodynamically possible, but they also highlight which geochemical variables (e.g., temperature, pressure, pH, composition) may control microbial activity and how the amount and type of biomass are affected by energy limitations. We will discuss recent results from sediment cores collected at the Peru Margin (active continental shelf with high primary productivity and significant organic matter accumulation), the South Pacific Gyre (ultra-slow sedimentation rate and low organic carbon content), and the Juan de Fuca Ridge flank (high rate of sedimentation influenced by hydrothermal circulation). However, this approach to evaluating bioenergetic potential and predicting microbial activity can be applied to any environment where the geochemistry is well characterized, even if microbiology data have not been collected. When Gibbs energies are calculated on a basis of per mole of electrons transferred (as is commonly done), aerobic oxidation of hydrogen and organic matter in South Pacific Gyre sediments is the most exergonic. Based on this, one might posit that the fastest catabolic rates and the largest biomass would be found there. However, cell counts at Juan de Fuca and the Peru Margin are several orders of magnitude higher. When recast as energy densities (in J per cm3 of sediment), we observe far more energy available in sediments at Juan de Fuca and the Peru Margin than at those in the South Pacific Gyre. We also note that the identity of the most exergonic reaction changes with depth, suggesting corresponding changes in the microbial community structure. The thermodynamic approach used here for energy supply can also be used for energy demand, including the often-considered minimum or threshold energy, also referred to as the biological energy quantum. Based on this energetic minimum theory, many reactions cannot support microbial communities because their energy yield is apparently too low. However, we show that when evaluated as energy densities, some energetically ';impossible' catabolisms become ';possible' and vice versa.

Improvement of suspended sediment concentration estimation for the Yarlung Zangbo river

NASA Astrophysics Data System (ADS)

Zeng, C.; Zhang, F.

2017-12-01

Suspended sediment load of a river represents integrated results of soil erosion, ecosystem variation and landform change occurring within basin over a specified period. Accurate estimation of suspended sediment concentration is important for calculating suspended sediment load, therefore is helpful for evaluating the impact of natural and anthropogenic factors on earth system processes under the background of global climate change. However, long-term observation of suspended sediment concentration usually very difficult in harsh condition areas e.g. rivers on the Tibet Plateau. This study proposed two sediment rating curve subdivision methods, the flood rank method and suspended sediment concentration stages method, to improve the estimations of daily suspended sediment concentration of the Yarlung Zangbo river during 2007 to 2009. The flood rank method, hypothesized that the higher water flow with larger erosive power can mobilize sediment sources not available during lower flows, suitable for application where sediments were mainly transported by first few flood events. The suspended sediment concentration stages method, assumed that precipitation is the dominating driving force of sediment erosion and transport processes during the flooding periods, suitable for application where soil erosion was closely related to precipitation events. Compared to traditional sediment rating curve and subdivision methods, results showed that the proposed methods can improve suspended sediment concentration and subsequent suspended sediment load estimations in the middle reach of the Yarlung Zangbo river with higher coefficients of determination (R2) and Nash-Sutcliffe efficiency coefficients (NSE), and yielded smaller bias (BIAS) and root-mean-square errors (RMSE). This study can provide guidelines for regional ecological and environmental management.

Carbon mineralization in Laptev and East Siberian sea shelf and slope sediment

NASA Astrophysics Data System (ADS)

Brüchert, Volker; Bröder, Lisa; Sawicka, Joanna E.; Tesi, Tommaso; Joye, Samantha P.; Sun, Xiaole; Semiletov, Igor P.; Samarkin, Vladimir A.

2018-01-01

The Siberian Arctic Sea shelf and slope is a key region for the degradation of terrestrial organic material transported from the organic-carbon-rich permafrost regions of Siberia. We report on sediment carbon mineralization rates based on O2 microelectrode profiling; intact sediment core incubations; 35S-sulfate tracer experiments; pore-water dissolved inorganic carbon (DIC); δ13CDIC; and iron, manganese, and ammonium concentrations from 20 shelf and slope stations. This data set provides a spatial overview of sediment carbon mineralization rates and pathways over large parts of the outer Laptev and East Siberian Arctic shelf and slope and allows us to assess degradation rates and efficiency of carbon burial in these sediments. Rates of oxygen uptake and iron and manganese reduction were comparable to temperate shelf and slope environments, but bacterial sulfate reduction rates were comparatively low. In the topmost 50 cm of sediment, aerobic carbon mineralization dominated degradation and comprised on average 84 % of the depth-integrated carbon mineralization. Oxygen uptake rates and anaerobic carbon mineralization rates were higher in the eastern East Siberian Sea shelf compared to the Laptev Sea shelf. DIC / NH4+ ratios in pore waters and the stable carbon isotope composition of remineralized DIC indicated that the degraded organic matter on the Siberian shelf and slope was a mixture of marine and terrestrial organic matter. Based on dual end-member calculations, the terrestrial organic carbon contribution varied between 32 and 36 %, with a higher contribution in the Laptev Sea than in the East Siberian Sea. Extrapolation of the measured degradation rates using isotope end-member apportionment over the outer shelf of the Laptev and East Siberian seas suggests that about 16 Tg C yr-1 is respired in the outer shelf seafloor sediment. Of the organic matter buried below the oxygen penetration depth, between 0.6 and 1.3 Tg C yr-1 is degraded by anaerobic processes, with a terrestrial organic carbon contribution ranging between 0.3 and 0.5 Tg yr-1.

Sources and cycling of major ions and nutrients in Devils Lake, North Dakota

USGS Publications Warehouse

Lent, R.M.

1994-01-01

Devils Lake is a saline lake in a large, closed drainage basin in northeastern North Dakota. Previous studies determined that major-ion and nutrient concentrations in Devils Lake are strongly affected by microbially mediated sulfate reduction and dissolution of sulfate and carbonate minerals in the bottom sediments. These studies documented substantial spatial variability in the magnitude of calculated benthic fluxes coincident with the horizontal salinity gradient in Devils Lake. The purpose of the present study is to evaluate seasonal variability in benthic-flux rates, and to understand the effect of these fluxes on the major-ion and nutrient chemistries in Devils Lake between May and October 1991. During the study period, the water column was well mixed, and specific conductance, pH, and temperature did not vary with depth. Dissolved oxygen was enriched near the lake surface due to photosynthesis. Major-ion concentrations and nutrient concentrations did not vary with depth. Because the water-quality data were obtained during open-water periods, the vertical profiles reflect well-mixed conditions. However, the first and last profiles for the study period did document near-bottom maxima of major cations. Secchi-disk depth varied from 0.82 meter on May 7,1991, to 2.13 meters on June 5, 1991. The mean Secchi-disk depth during the study period was 1.24 meters. Seasonal variations in Secchi-disk depths were attributed to variations in primary productivity and phytoplankton communities. Nutrient cycles in Devils Lake were evaluated using gross primary productivity rate data, sediment trap data, and major-ion and nutrient benthic-flux rate data. Gross primary productivity rate was smallest in May (0.076 gram of carbon per square meter per day) and largest in September (1.8 grams of carbon per square meter per day). Average gross primary productivity for the study period was 0.87 gram of carbon per square meter per day. Average gross primary productivity is consistent with historic data from Devils Lake and with data from other eutrophic lakes.The average flux of organic carbon for the study period was 12 grams per square meter per day. The calculated carbon to nitrogen to phosphorus ratio (317:25:1) is similar to the Redfield ratio (106:16:1); therefore, most organic matter probably is derived from lacustrine phytoplankton.Calculated benthic-flux rates indicated that bottom sediments are important sources of majorions and nutrients to Devils Lake. Only one of the cores collected during this study indicated a net sulfate flux from the lake into the sediments. Seasonal variations in major-ion and nutrient benthic fluxes generally were small. However, there were important differences between the calculated benthic fluxes for this study and the calculated benthic fluxes for 1990. Calculated benthic fluxes of bicarbonate, ammonia, and phosphorus for this study were smaller than calculated benthic fluxes for 1990. The large differences between fluxes for 1990 and 1991 were attributed to calm, stratified water-column conditions in 1990 and well-mixed water-column conditions in 1991.The role of benthic fluxes in the chemical mass balances in Devils Lake was evaluated by calculating response times for major ions and nutrients in Devils Lake. The calculated response times for major ions in Devils Lake ranged from 6.7 years for bicarbonate to 34 years for sulfur (as 804). The response times for major ions are significantly shorter than previous estimates that did not include benthic fluxes. In addition, the relatively short response times for nitrogen (4.2 years) and phosphorus (0.95 year) indicate that nutrients are recycled rapidly between bottom sediments and the lake. During the study period, benthic fluxes were the dominant source of major ions and nutrients to Devils Lake and greatly reduced the response times of all major ions and nutrients for Devils Lake. As a result, bottom-sediment processes appear to buffer major-ion and nutrient concentrations in the lake. Any future attempt to evaluate water quality in Devils Lake should include the effects of bottom-sediment processes.

Sediment calibration strategies of Phase 5 Chesapeake Bay watershed model

USGS Publications Warehouse

Wu, J.; Shenk, G.W.; Raffensperger, Jeff P.; Moyer, D.; Linker, L.C.; ,

2005-01-01

Sediment is a primary constituent of concern for Chesapeake Bay due to its effect on water clarity. Accurate representation of sediment processes and behavior in Chesapeake Bay watershed model is critical for developing sound load reduction strategies. Sediment calibration remains one of the most difficult components of watershed-scale assessment. This is especially true for Chesapeake Bay watershed model given the size of the watershed being modeled and complexity involved in land and stream simulation processes. To obtain the best calibration, the Chesapeake Bay program has developed four different strategies for sediment calibration of Phase 5 watershed model, including 1) comparing observed and simulated sediment rating curves for different parts of the hydrograph; 2) analyzing change of bed depth over time; 3) relating deposition/scour to total annual sediment loads; and 4) calculating "goodness-of-fit' statistics. These strategies allow a more accurate sediment calibration, and also provide some insightful information on sediment processes and behavior in Chesapeake Bay watershed.

Using cosmogenic nuclides to contrast rates of erosion and sediment yield in a semi-arid, arroyo-dominated landscape, Rio Puerco Basin, New Mexico

USGS Publications Warehouse

Bierman, P.R.; Reuter, J.M.; Pavich, M.; Gellis, A.C.; Caffee, M.W.; Larsen, J.

2005-01-01

Analysis of in-situ-produced 10Be and 26Al in 52 fluvial sediment samples shows that millennial-scale rates of erosion vary widely (7 to 366 m Ma-1) through the lithologically and topographically complex Rio Puerco Basin of northern New Mexico. Using isotopic analysis of both headwater and downstream samples, we determined that the semi-arid, Rio Puerco Basin is eroding, on average, about 100 m Ma-1. This rapid rate of erosion is consistent with estimates made using other techniques and is likely to result from a combination of easily eroded lithologies, sparse vegetation, and monsoon-dominated rainfall. Data from 331 stream water samples collected by the US Geological Survey between 1960 and 1995 are consistent with basin-wide, average chemical denudation rates of only about 1??4 m Ma-1; thus, the erosion rates we calculate may be considered rates of sediment generation because physical weathering accounts for almost 99 per cent of mass loss. The isotopic data reveal that sediment is generally well mixed downstream with the area-weighted average sediment generation rate for 16 headwater samples (234 ton km-2 a-1 for basin area 170 to 1169 km2) matching well that estimated from a single sample collected far downstream (238 ton km-2 a-1, basin area = 14 225 km2). A series of 15 samples, collected from an arroyo wall and representing deposition through the late Holocene, indicates that 10Be concentration in sediment delivered by the fluvial system has not changed appreciably over the last 1200 years despite at least two cycles of arroyo cutting and filling. Other samples (n = 21) were collected along the drainage network. Rio Puerco erosion rates scale directly with a variety of metrics describing vegetation, precipitation, and rock erodibility. Using the headwater basins for calibration, the erosion rates for both the downstream samples and also the data set as a whole, are best modelled by considering a combination of relief and vegetation metrics, both of which co-vary with precipitation and erodibility as inferred from lithology. On average, contemporary sediment yields, determined by monitoring suspended-sediment discharge, exceed cosmogenically determined millennial-scale erosion rates by nearly a factor of two. This discrepancy, between short-term rates of sediment yield and long-term rates of erosion, suggests that more sediment is currently being exported from the basin than is being produced. Because the failure of incised channel walls and the head cutting of arroyo complexes appear to be the main sources of channel sediment today, this incongruence between rates of sediment supply and sediment yield is likely to be transitory, reflecting the current states of the arroyo cycle and perhaps the influence of current or past land-use patterns. Copyright ?? 2005 John Wiley & Sons, Ltd.

Organic carbon storage and benthic consumption in sediments of northern fjords (60-80°N)

NASA Astrophysics Data System (ADS)

Włodarska-Kowalczuk, Maria; Zaborska, Agata; Jankowska, Emilia; Mazurkiewicz, Mikołaj

2017-04-01

Fjords have been recently recognized as hotspots of organic carbon storage, with organic carbon burial rates one hundred times larger than the global ocean average, accounting for 11% of global annual marine carbon burial (Smith et al. (2015) Nature Geoscience 8: 450-453). The organic carbon production and processing in coastal waters and sediments are controlled by environmental settings that are likely to be reshaped in the course of the global warming. The fastest and strongest changes are to occur in polar regions. In the present study we compare organic carbon stocks, accumulation and burial in temperate (Raunefjorden, Ullsfjorden, Balsfjorden) and Arctic (Hornsund, Kongsfjorden, Rijpfjorden) fjords located along the latitudinal/thermal gradient from the southern Norway (60 °N) to North of Svalbard (80 °N). The sediment cores were collected at 3 to 5 stations within the central basin at 150-300 m in each fjord during r/v Helmer Hansen and r/v Oceania cruises in 2014 and 2015. Vertical patterns of grain size and organic matter content and sources (Corg concentration, stable isotope δ13C signature, photosynthetic pigments concentration) have been analyzed. Sediment accumulation rates have been estimated with use of 210Pb dating method. Fresh carbon accumulation rate was estimated based on organic carbon concentration is surface sediments and mass sediment accumulation rate. The variability in metazoan productivity and carbon consumption (calculated based on the macro- and meiobenthic species biomass spectra in samples collected at the same stations) was also assessed to explore the patterns of biological controls of carbon storage in sediments. Carbon burial was estimated by multiplying organic carbon concentration in deepest sampled sediments and mass sediment accumulation rate. The effects of contrasting hydrological regimes and biological activity on the carbon storage in the studied fjords are discussed from the perspective of possible effects of climate warming driven changes on the Arctic fjordic sedimentary systems.

Radionuclides in ornithogenic sediments as evidence for recent warming in the Ross Sea region, Antarctica.

PubMed

Nie, Yaguang; Xu, Liqiang; Liu, Xiaodong; Emslie, Steven D

2016-07-01

Radionuclides including (210)Pb, (226)Ra and (137)Cs were analyzed in eight ornithogenic sediment profiles from McMurdo Sound, Ross Sea region, East Antarctica. Equilibration between (210)Pb and (226)Ra were reached in all eight profiles, enabling the determination of chronology within the past two centuries through the Constant Rate of Supply (CRS) model. Calculated fluxes of both (210)Pb and (137)Cs varied drastically among four of the profiles (MB4, MB6, CC and CL2), probably due to differences in their sedimentary environments. In addition, we found the flux data exhibiting a clear decreasing gradient in accordance with their average deposition rate, which was in turn related to the specific location of the profiles. We believe this phenomenon may correspond to global warming of the last century, since warming-induced surface runoff would bring more inflow water and detritus to the coring sites, thus enhancing the difference among the profiles. To verify this hypothesis, the deposition rate against age of the sediments was calculated based on their determined chronology, which showed ascending trends in all four profiles. The significant increase in deposition rates over the last century is probably attributable to recent warming, implying a potential utilization of radionuclides as environmental indicators in this region. Copyright © 2016. Published by Elsevier B.V.

Erosion of an ancient mountain range, the Great Smoky Mountains, North Carolina and Tennessee

USGS Publications Warehouse

Matmon, A.; Bierman, P.R.; Larsen, J.; Southworth, S.; Pavich, M.; Finkel, R.; Caffee, M.

2003-01-01

Analysis of 10Be and 26Al in bedrock (n=10), colluvium (n=5 including grain size splits), and alluvial sediments (n=59 including grain size splits), coupled with field observations and GIS analysis, suggest that erosion rates in the Great Smoky Mountains are controlled by subsurface bedrock erosion and diffusive slope processes. The results indicate rapid alluvial transport, minimal alluvial storage, and suggest that most of the cosmogenic nuclide inventory in sediments is accumulated while they are eroding from bedrock and traveling down hill slopes. Spatially homogeneous erosion rates of 25 - 30 mm Ky-1 are calculated throughout the Great Smoky Mountains using measured concentrations of cosmogenic 10Be and 26Al in quartz separated from alluvial sediment. 10Be and 26Al concentrations in sediments collected from headwater tributaries that have no upstream samples (n=18) are consistent with an average erosion rate of 28 ?? 8 mm Ky-1, similar to that of the outlet rivers (n=16, 24 ?? 6 mm Ky-1), which carry most of the sediment out of the mountain range. Grain-size-specific analysis of 6 alluvial sediment samples shows higher nuclide concentrations in smaller grain sizes than in larger ones. The difference in concentrations arises from the large elevation distribution of the source of the smaller grains compared with the narrow and relatively low source elevation of the large grains. Large sandstone clasts disaggregate into sand-size grains rapidly during weathering and downslope transport; thus, only clasts from the lower parts of slopes reach the streams. 26Al/10Be ratios do not suggest significant burial periods for our samples. However, alluvial samples have lower 26Al/10Be ratios than bedrock and colluvial samples, a trend consistent with a longer integrated cosmic ray exposure history that includes periods of burial during down-slope transport. The results confirm some of the basic ideas embedded in Davis' geographic cycle model, such as the reduction of relief through slope processes, and of Hack's dynamic equilibrium model such as the similarity of erosion rates across different lithologies. Comparing cosmogenic nuclide data with other measured and calculated erosion rates for the Appalachians, we conclude that rates of erosion, integrated over varying time periods from decades to a hundred million years are similar, the result of equilibrium between erosion and isostatic uplift in the southern Appalachian Mountains.

Longshore Sediment Transport Rate Calculated Incorporating Wave Orbital Velocity Fluctuations

DTIC Science & Technology

2006-09-01

distribution of longshore sediment transport in the surf zone is necessary in the design and planning of groins, jetties, weirs and pipeline landfalls...transported by any current. Breaker height is defined as the vertical distance between the wave crest and the preceding wave trough at incipient...terminology; spilling breakers occur if the wave crest becomes unstable and flows down the front face of the wave producing a foamy water surface; plunging

Sediment Flux and Storage in a Rural Southeastern Piedmont River System

NASA Astrophysics Data System (ADS)

Jackson, C. R.; Martin, J. K.

2001-12-01

A sediment budget was developed for a representative rural southeastern Piedmont watershed to provide information on the relative importance of sediment sources. Sediment issues in the southeastern Piedmont are complicated by the so-called legacy sediment produced by poor farming practices during the cotton-farming era, approximately 1810-1930. The Murder Creek basin near Monticello, GA was chosen because: it featured forestry and agriculture as the principal land uses; a USGS gage provided a flow record; and the creek deposited in a reservoir built in 1948. Suspended load export was calculated using a sediment rating curve and the USGS flow time series. Bed load export was determined by estimating the volume of sediment deposited in the reservoir since construction. Unpaved road erosion was estimated using the WEPP model, and other surface erosion was estimated using USLE and delivery ratios. Historical floodplain storage was determined by coring floodplain deposits, measuring the depth to the pre-historic/historic sediment interface, and multiplying by the area of the floodplain. Recent accretion rates were estimated using dendrogeomorphology. Results showed that the practices of the cotton farming era deposited an average of 1.6 meters of sediment on the floodplains. This depth was relatively uniform across the watershed. The cotton-farming sediment in storage exceeds the current annual export by a factor of about 5000. Approximately half of the current export comes from current inputs, and half comes from remobilized floodplain sediments.

Factors Influencing Watershed Average Erosion Rates Calculated from Reservoir Sedimentation in Eastern USA

NASA Astrophysics Data System (ADS)

Ahamed, A.; Snyder, N. P.; David, G. C.

2014-12-01

The Reservoir Sedimentation Database (ResSed), a catalogue of reservoirs and depositional data that has recently become publically available, allows for rapid calculation of sedimentation rates and rates of capacity loss over short (annual to decadal) timescales. This study is a statistical investigation of factors controlling watershed average erosion rates (E) in eastern United States watersheds. We develop an ArcGIS-based model that delineates watersheds upstream of ResSed dams and calculate drainage areas to determine E for 191 eastern US watersheds. Geomorphic, geologic, regional, climatic, and land use variables are quantified within study watersheds using GIS. Erosion rates exhibit a large amount of scatter, ranging from 0.001 to 1.25 mm/yr. A weak inverse power law relationship between drainage area (A) and E (R2 = 0.09) is evident, similar to other studies (e.g. Milliman and Syvitski, 1992; Koppes and Montgomery, 2009). Linear regressions reveal no relationship between mean watershed slope (S) and E, possibly due to the relatively low relief of the region (mean S for all watersheds is 6°). Analysis of Variance shows that watersheds in formerly glaciated regions exhibit a statistically significant lower mean E (0.06 mm/year) than watersheds in unglaciated regions (0.12 mm/year), but that watersheds with different dam purposes show no significant differences in mean E. Linear regressions reveal no relationships between E and land use parameters like percent agricultural land and percent impervious surfaces (I), but classification and regression trees indicate that watersheds in highly developed regions (I > 34%) exhibit mean E (0.36 mm/year) that is four times higher than watersheds in less developed (I < 34%) regions (0.09 mm/year). Further, interactions between land use variables emerge in formerly glaciated regions, where increased agricultural land results in higher rates of annual capacity loss in reservoirs (R2 = 0.56). Plots of E versus timescale of measurement (e.g., Sadler and Jerolmack, 2014) show that nearly the full range of observed E, including the highest values, are seen over short survey intervals (< 20 years), suggesting that whether or not large sedimentation events (such as floods) occur between two surveys may explain the high degree of variability in measured rates.

Assessment of Holocene soil erosion rates on the loess plateau in East Poland using sedimentary archives from closed depressions

NASA Astrophysics Data System (ADS)

Kołodyńska-Gawrysiak, Renata; Poesen, Jean; Gawrysiak, Leszek

2016-04-01

Closed depressions (CDs) are typical geomorphological features of the European loess belt. They are closed sedimentation basins that enable the estimation of long-term soil erosion rates for different land use environments. This study was conducted in eastern Poland (Nałęczów Plateau). In this region CDs are rather small landforms and the area of 70% of all CDs does not exceed 1500 m2. The study objective was to assess Holocene soil erosion rates in the loess plateau based on a quantitative analysis of colluvial sediments deposited in CDs. Two representative CDs were selected for this study: one CD is located in an old (long-term) forest and the other is situated in a long-term agricultural land. The maximum depth of the CD in the forest, the mean slope gradient and area of the corresponding catchment are 4.9 m, 3.410 and 7568 m² respectively. For the CD in agricultural land these values are 3.2 m, 2.760 and 5156 m² respectively. In both CDs several dozen of drillings and two trenches (2 m long, 1m wide, 2 m deep) were made in the deepest point of the CDs. Mean long-term soil erosion rates were calculated based on the stratigraphy of the soil-sediment sequence infilling the CDs. C-14 and OSL datings of soils and colluvial sediments within the CDs were obtained. For the long-term agricultural used catchment of the CD it was calculated that since 6.31 ± 0.35 ka BP the mean annual soil loss due to water and tillage erosion is 0.63-0.7 t/ha/year or 279.3 mm. In the prehistoric period since 6.31 ± 0.35 ka BP until 1026-1162 AD the mean annual soil erosion rate amounted to 0,10-0.11 t/ha/year or 41.5 mm. During the last ca. 1000 years mean soil erosion rates increased to 3.99-4.63 t/ha/year or 249.2 mm. Results of long-term soil erosion rates (calculated using colluvial sediment sequences in CDs) from agricultural catchments in the loess regions of eastern Poland (this study) and Central Belgium (Gillijns et al. 2005) are quite similar. For the forested catchment of the CD the mean annual soil erosion rate since at least ca. 1000 years is 0.073-0.086 t/ha/year or 41.9 mm. In this catchment soil erosion and correlative colluviation deposits occurred mainly in prehistoric times. CDs play an important role for archiving sediments which allow to reconstruct both natural and anthropogenic processes in the past. The study of these sediment archives allows a better understanding of human-environment interactions and its impact on long-term soil erosion rates. Acknowledgements: The research project was financially supported by the National Centre of Science - project PB-B-12-287-00-13: The origin and evolution of closed depressions in the loess area of the Lublin Upland and their importance for the reconstruction of postglacial morphogenesis of the loess covers. References: Gillijns K., Poesen J., Deckers J., 2005: On the characteristics and origin of closed depression in loess-derived soils in Europe- a case study from central Belgium. Catena 60, 43-58.

Mapping, Monitoring, and Modeling Geomorphic Processes to Identify Sources of Anthropogenic Sediment Pollution in West Maui, Hawai'i

NASA Astrophysics Data System (ADS)

Cerovski-Darriau, C.; Stock, J. D.; Winans, W. R.

2016-12-01

Episodic storm runoff in West Maui (Hawai'i) brings plumes of terrestrially-sourced fine sediment to the nearshore ocean environment, degrading coral reef ecosystems. The sediment pollution sources were largely unknown, though suspected to be due to modern human disturbance of the landscape, and initially assumed to be from visibly obvious exposed soil on agricultural fields and unimproved roads. To determine the sediment sources and estimate a sediment budget for the West Maui watersheds, we mapped the geomorphic processes in the field and from DEMs and orthoimagery, monitored erosion rates in the field, and modeled the sediment flux using the mapped processes and corresponding rates. We found the primary source of fine sands, silts and clays to be previously unidentified fill terraces along the stream bed. These terraces, formed during legacy agricultural activity, are the banks along 40-70% of the streams where the channels intersect human-modified landscapes. Monitoring over the last year shows that a few storms erode the fill terraces 10-20 mm annually, contributing up to 100s of tonnes of sediment per catchment. Compared to the average long-term, geologic erosion rate of 0.03 mm/yr, these fill terraces alone increase the suspended sediment flux to the coral reefs by 50-90%. Stakeholders can use our resulting geomorphic process map and sediment budget to inform the location and type of mitigation effort needed to limit terrestrial sediment pollution. We compare our mapping, monitoring, and modeling (M3) approach to NOAA's OpenNSPECT model. OpenNSPECT uses empirical hydrologic and soil erosion models paired with land cover data to compare the spatially distributed sediment yield from different land-use scenarios. We determine the relative effectiveness of calculating a baseline watershed sediment yield from each approach, and the utility of calibrating OpenNSEPCT with M3 results to better forecast future sediment yields from land-use or climate change scenarios.

Assessing Chemical Retention Process Controls in Ponds

NASA Astrophysics Data System (ADS)

Torgersen, T.; Branco, B.; John, B.

2002-05-01

Small ponds are a ubiquitous component of the landscape and have earned a reputation as effective chemical retention devices. The most common characterization of pond chemical retention is the retention coefficient, Ri= ([Ci]inflow-[Ci] outflow)/[Ci]inflow. However, this parameter varies widely in one pond with time and among ponds. We have re-evaluated literature reported (Borden et al., 1998) monthly average retention coefficients for two ponds in North Carolina. Employing a simple first order model that includes water residence time, the first order process responsible for species removal have been separated from the water residence time over which it acts. Assuming the rate constant for species removal is constant within the pond (arguable at least), the annual average rate constant for species removal is generated. Using the annual mean rate constant for species removal and monthly water residence times results in a significantly enhanced predictive capability for Davis Pond during most months of the year. Predictive ability remains poor in Davis Pond during winter/unstratified periods when internal loading of P and N results in low to negative chemical retention. Predictive ability for Piedmont Pond (which has numerous negative chemical retention periods) is improved but not to the same extent as Davis Pond. In Davis Pond, the rate constant for sediment removal (each month) is faster than the rate constant for water and explains the good predictability for sediment retention. However, the removal rate constant for P and N is slower than the removal rate constant for sediment (longer water column residence time for P,N than for sediment). Thus sedimentation is not an overall control on nutrient retention. Additionally, the removal rate constant for P is slower than for TOC (TOC is not the dominate removal process for P) and N is removed slower than P (different in pond controls). For Piedmont Pond, sediment removal rate constants are slower than the removal rate constant for water indicating significant sediment resuspension episodes. It appears that these sediment resuspension events are aperiodic and control the loading and the chemical retention capability of Piedmont Pond for N,P,TOC. These calculated rate constants reflect the differing internal loading processes for each component and suggest means and mechanisms for the use of ponds in water quality management.

13. Groundwater in urban seashore sediments affected by tunnel constructions

NASA Astrophysics Data System (ADS)

Kitterød, Nils-Otto

2014-05-01

The purpose of this study was to examine the impact of a planned tunnel construction on the local groundwater level in the archeological deposits at the Old Wharf (Bryggen) of Bergen. The groundwater level is a function of infiltration rates, transmissivity, and boundary conditions. These variables were deduced from available data and supplemented by leakage measurements into the existing Railway tunnel located upstream of the Bryggen area. Previous studies have documented that the pore water in the deposits at Bryggen has different origin (viz fresh precipitation; leakage from drainage systems; infiltration of seawater; infiltration via the bedrock). The catchment of Bryggen is characterized by variable topography (from sea level to about 500 m a.m.s.l.) and steep gradients. Major parts of the catchment have very sparse sediment cover and can be considered as exposed bedrock. The major sediment volumes are deposited close to the sea front. In the upper part of the catchment, the groundwater level in the bedrock is close to the surface. Some observations indicate that boreholes located in lower part of the catchment have artesian pressure, which implies that there is a groundwater flux from the bedrock and into the sediments. Based on this conceptual model, a numerical model was constructed where the seawater was the boundary condition at one side and the groundwater divide on the other side. Transmissivities in the bedrock were deduced from pumping analysis, and steady state infiltration rates was calibrated to give simulated groundwater levels that were consistent to observations. Given these model simplifications, it was possible to calculate a groundwater level in the sediments at Bryggen were all water into the sediments came from the bedrock only. The simulated groundwater level captured roughly the observed groundwater levels. After simulation of the natural groundwater level (i.e. without any artificial extraction of water in the catchment), the impact of the water leakage into the existing tunnels was calculated. Given the relatively rough estimates on water leakage into existing tunnels (4 liter/day/meter of tunnel), the calculated decline of the groundwater table was less than 1% of the natural groundwater head (<1 cm). If leakage rates were increased to one and two orders of magnitude, the steady state groundwater decline would be from 5% to more than 35% of the reference groundwater head (4 - 15 cm). The reason for this relatively robust groundwater conditions in the sediments are the boundary conditions: Without any local water sinks in the deposits, the steady-state groundwater table at Bryggen will always be higher than the seawater level. A crucial point for these results was the leakage rates into the existing tunnels, which is highly recommended to monitor before execution of any new tunnel constructions.

(210)Pb as a tracer of soil erosion, sediment source area identification and particle transport in the terrestrial environment.

PubMed

Matisoff, Gerald

2014-12-01

Although (137)Cs has been used extensively to study soil erosion and particle transport in the terrestrial environment, there has been much less work using excess or unsupported (210)Pb ((210)Pbxs) to study the same processes. Furthermore, since (137)Cs activities in soils are decreasing because of radioactive decay, some locations have an added complication due to the addition of Chernobyl-derived (137)Cs, and the activities of (137)Cs in the southern hemisphere are low, there is a need to develop techniques that use (210)Pbxs to provide estimates of rates of soil erosion and particle transport. This paper reviews the current status of (210)Pbxs methods to quantify soil erosion rates, to identify and partition suspended sediment source areas, and to determine the transport rates of particles in the terrestrial landscape. Soil erosion rates determined using (210)Pbxs are based on the unsupported (210)Pb ((210)Pbxs) inventory in the soil, the depth distribution of (210)Pbxs, and a mass balance calibration ('conversion model') that relates the soil inventory to the erosion rate using a 'reference site' at which neither soil erosion nor soil deposition has occurred. In this paper several different models are presented to illustrate the effects of different model assumptions such as the timing, depth and rates of the surface soil mixing on the calculated erosion rates. The suitability of model assumptions, including estimates of the depositional flux of (210)Pbxs to the soil surface and the post-depositional mobility of (210)Pb are also discussed. (210)Pb can be used as one tracer to permit sediment source area identification. This sediment 'fingerprinting' has been extended far beyond using (210)Pb as a single radioisotope to include numerous radioactive and stable tracers and has been applied to identifying the source areas of suspended sediment based on underlying rock type, land use (roads, stream banks, channel beds, cultivated or uncultivated lands, pasture lands, forested lands, construction sites, undisturbed lands) or style of erosion (sheet wash, rills, bank). The transport time of particles in the terrestrial system can be estimated using (7)Be/(210)Pbxs radionuclide ratios and from mass balance models of (210)Pbxs and/or (7)Be in streams. Watershed residence times can be calculated from the radionuclide inventory and the erosional loss rate. Copyright © 2014 Elsevier Ltd. All rights reserved.

Rapid sedimentation of iron oxyhydroxides in an active hydrothermal shallow semi-enclosed bay at Satsuma Iwo-Jima Island, Kagoshima, Japan

NASA Astrophysics Data System (ADS)

Kiyokawa, Shoichi; Ueshiba, Takuya

2015-04-01

Hydrothermal activity is common in the fishing port of Nagahama Bay, a small semi-enclosed bay located on the southwest coast of Satsuma Iwo-Jima Island (38 km south of Kyushu Island, Japan). The bay contains red-brown iron oxyhydroxides and thick deposits of sediment. In this work, the high concentration and sedimentation rates of oxyhydroxide in this bay were studied and the sedimentary history was reconstructed. Since dredging work in 1998, a thickness of 1.0-1.5 m of iron oxyhydroxide-rich sediments has accumulated on the floor of the bay. To estimate the volume of iron oxyhydroxide sediments and the amount discharged from hydrothermal vents, sediment traps were operated for several years and 13 sedimentary core samples were collected to reconstruct the 10-year sedimentary history of Nagahama Bay. To confirm the timing of sedimentary events, the core data were compared with meteorological records obtained on the island, and the ages of characteristic key beds were thus identified. The sedimentation rate of iron oxyhydroxide mud was calculated, after correcting for sediment input from other sources. The sediments in the 13 cores from Nagahama Bay consist mainly of iron oxyhydroxide mud, three thick tephra beds, and a topmost thick sandy mud bed. Heavy rainfall events in 2000, 2001, 2002, and 2004-2005 coincide with tephra beds, which were reworked from Iwo-Dake ash deposits to form tephra-rich sediment. Strong typhoon events with gigantic waves transported outer-ocean-floor sediments and supplied quartz, cristobalite, tridymite, and albite sands to Nagahama Bay. These materials were redeposited together with bay sediments as the sandy mud bed. Based on the results from the sediment traps and cores, it is estimated that the iron oxyhydroxide mud accumulated in the bay at the relatively rapid rate of 33.3 cm/year (from traps) and 2.8-4.9 cm/year (from cores). The pore water contents within the sediment trap and core sediments are 73%-82% and 47%-67%, respectively. The estimated production of iron oxyhydroxide for the whole fishing port from trap cores is 142.7-253.3 t/year/5000 m2. From sediment cores, however, the accumulation of iron oxyhydroxide sediments on the sea floor is 39-95 t/year/5000 m2. This finding indicates that the remaining 63%-73% of iron was transported out to sea from Nagahama Bay. Even with a high rate of iron oxyhydroxide production, the sedimentation rate of iron oxyhydroxides in the bay is considerably higher than that observed in modern deep-ocean sediments. This example of rapid and abundant oxyhydroxide sedimentation might provide a modern analog for the formation of iron deposits in the geological record, such as ironstones and banded iron formations.

Predicting Sediment Thickness on Vanished Ocean Crust Since 200 Ma

NASA Astrophysics Data System (ADS)

Dutkiewicz, A.; Müller, R. D.; Wang, X.; O'Callaghan, S.; Cannon, J.; Wright, N. M.

2017-12-01

Tracing sedimentation through time on existing and vanished seafloor is imperative for constraining long-term eustasy and for calculating volumes of subducted deep-sea sediments that contribute to global geochemical cycles. We present regression algorithms that incorporate the age of the ocean crust and the mean distance to the nearest passive margin to predict sediment thicknesses and long-term decompacted sedimentation rates since 200 Ma. The mean sediment thickness decreases from ˜220 m at 200 Ma to a minimum of ˜140 m at 130 Ma, reflecting the replacement of old Panthalassic ocean floor with young sediment-poor mid-ocean ridges, followed by an increase to ˜365 m at present-day. This increase reflects the accumulation of sediments on ageing abyssal plains proximal to passive margins, coupled with a decrease in the mean distance of any parcel of ocean crust to the nearest passive margin by over 700 km, and a doubling of the total passive margin length at present-day. Mean long-term sedimentation rates increase from ˜0.5 cm/ky at 160 Ma to over 0.8 cm/ky today, caused by enhanced terrigenous sediment influx along lengthened passive margins, superimposed by the onset of ocean-wide carbonate sedimentation. Our predictive algorithms, coupled to a plate tectonic model, provide a framework for constraining the seafloor sediment-driven eustatic sea-level component, which has grown from ˜80 to 210 m since 120 Ma. This implies a long-term sea-level rise component of 130 m, partly counteracting the contemporaneous increase in ocean basin depth due to progressive crustal ageing.

An Integrated Field and Laboratory Study of the Bioavailability of Metal Contaminants in Sediments

DTIC Science & Technology

2012-12-01

investigation using high-performance liquid chromatography with detection by inductively coupled plasma mass spectrometry. J Anal Atom Spectrom 8:1075...exposure experiments consisted of two parts - uptake and efflux. Uptake rate constants (ku) equaled the metal concentration accumulated per body mass ...of dry mass of defecated sediment per dry mass of worm per time (g g-1 d-1), were calculated based on the dry mass of feces that were periodically

Sediment contributions from floodplains and legacy sediments to Piedmont streams of Baltimore County, Maryland

NASA Astrophysics Data System (ADS)

Donovan, Mitchell; Miller, Andrew; Baker, Matthew; Gellis, Allen

2015-04-01

Disparity between watershed erosion rates and downstream sediment delivery has remained an important theme in geomorphology for many decades, with the role of floodplains in sediment storage as a common focus. In the Piedmont Province of the eastern USA, upland deforestation and agricultural land use following European settlement led to accumulation of thick packages of overbank sediment in valley bottoms, commonly referred to as legacy deposits. Previous authors have argued that legacy deposits represent a potentially important source of modern sediment loads following remobilization by lateral migration and progressive channel widening. This paper seeks to quantify (1) rates of sediment remobilization from Baltimore County floodplains by channel migration and bank erosion, (2) proportions of streambank sediment derived from legacy deposits, and (3) potential contribution of net streambank erosion and legacy sediments to downstream sediment yield within the Mid-Atlantic Piedmont. We calculated measurable gross erosion and deposition rates within the fluvial corridor along 40 valley segments from 18 watersheds with drainage areas between 0.18 and 155 km2 in Baltimore County, Maryland. We compared stream channel and floodplain morphology from lidar-based digital elevation data collected in 2005 with channel positions recorded on 1:2400 scale topographic maps from 1959-1961 in order to quantify 44-46 years of channel change. Sediment bulk density and particle size distributions were characterized from streambank and channel deposit samples and used for volume to mass conversions and for comparison with other sediment sources. Average annual lateral migration rates ranged from 0.04 to 0.19 m/y, which represented an annual migration of 2.5% (0.9-4.4%) channel width across all study segments, suggesting that channel dimensions may be used as reasonable predictors of bank erosion rates. Gross bank erosion rates varied from 43 to 310 Mg/km/y (median = 114) and were positively correlated with drainage area. Measured deposition within channels accounted for an average of 46% (28-75%) of gross erosion, with deposition increasingly important in larger drainages. Legacy sediments accounted for 6-90% of bank erosion at individual study segments, represented about 60% of bank height at most exposures, and accounted for 57% (± 16%) of the measured gross erosion. Extrapolated results indicated that first- and second-order streams accounted for 62% (± 38%) of total streambank erosion from 1005 km2 of northern Baltimore County. After accounting for estimated redeposition, extrapolated net streambank sediment yields (72 Mg/km2/y) constituted 70% of estimated average Piedmont watershed yields (104 Mg/km2/y). The results suggest that streambank sediments are a relatively large source of sediment from Piedmont tributaries to the Chesapeake Bay.

Sediment contributions from floodplains and legacy sediments to Piedmont streams of Baltimore County, Maryland

USGS Publications Warehouse

Donovan, Mitchell; Miller, Andrew; Baker, Matthew; Gellis, Allen C.

2015-01-01

Disparity between watershed erosion rates and downstream sediment delivery has remained an important theme in geomorphology for many decades, with the role of floodplains in sediment storage as a common focus. In the Piedmont Province of the eastern USA, upland deforestation and agricultural land use following European settlement led to accumulation of thick packages of overbank sediment in valley bottoms, commonly referred to as legacy deposits. Previous authors have argued that legacy deposits represent a potentially important source of modern sediment loads following remobilization by lateral migration and progressive channel widening. This paper seeks to quantify (1) rates of sediment remobilization from Baltimore County floodplains by channel migration and bank erosion, (2) proportions of streambank sediment derived from legacy deposits, and (3) potential contribution of net streambank erosion and legacy sediments to downstream sediment yield within the Mid-Atlantic Piedmont.We calculated measurable gross erosion and deposition rates within the fluvial corridor along 40 valley segments from 18 watersheds with drainage areas between 0.18 and 155 km2 in Baltimore County, Maryland. We compared stream channel and floodplain morphology from lidar-based digital elevation data collected in 2005 with channel positions recorded on 1:2400 scale topographic maps from 1959–1961 in order to quantify 44–46 years of channel change. Sediment bulk density and particle size distributions were characterized from streambank and channel deposit samples and used for volume to mass conversions and for comparison with other sediment sources.Average annual lateral migration rates ranged from 0.04 to 0.19 m/y, which represented an annual migration of 2.5% (0.9–4.4%) channel width across all study segments, suggesting that channel dimensions may be used as reasonable predictors of bank erosion rates. Gross bank erosion rates varied from 43 to 310 Mg/km/y (median = 114) and were positively correlated with drainage area. Measured deposition within channels accounted for an average of 46% (28–75%) of gross erosion, with deposition increasingly important in larger drainages. Legacy sediments accounted for 6–90% of bank erosion at individual study segments, represented about 60% of bank height at most exposures, and accounted for 57% (± 16%) of the measured gross erosion. Extrapolated results indicated that first- and second-order streams accounted for 62% (± 38%) of total streambank erosion from 1005 km2 of northern Baltimore County. After accounting for estimated redeposition, extrapolated net streambank sediment yields (72 Mg/km2/y) constituted 70% of estimated average Piedmont watershed yields (104 Mg/km2/y). The results suggest that streambank sediments are a relatively large source of sediment from Piedmont tributaries to the Chesapeake Bay.

Daily reservoir sedimentation model: Case study from the Fena Valley Reservoir, Guam

USGS Publications Warehouse

Marineau, Mathieu D.; Wright, Scott A.

2017-01-01

A model to compute reservoir sedimentation rates at daily timescales is presented. The model uses streamflow and sediment load data from nearby stream gauges to obtain an initial estimate of sediment yield for the reservoir’s watershed; it is then calibrated to the total deposition calculated from repeat bathymetric surveys. Long-term changes to reservoir trapping efficiency are also taken into account. The model was applied to the Fena Valley Reservoir, a water supply reservoir on the island of Guam. This reservoir became operational in 1951 and was recently surveyed in 2014. The model results show that the highest rate of deposition occurred during two typhoons (Typhoon Alice in 1953 and Typhoon Tingting in 2004); each storm decreased reservoir capacity by approximately 2–3% in only a few days. The presented model can be used to evaluate the impact of an extreme event, or it can be coupled with a watershed runoff model to evaluate potential impacts to storage capacity as a result of climate change or other hydrologic modifications.

Distribution and Rate of Methane Oxidation in Sediments of the Florida Everglades †

PubMed Central

King, Gary M.; Roslev, Peter; Skovgaard, Henrik

1990-01-01

Rates of methane emission from intact cores were measured during anoxic dark and oxic light and dark incubations. Rates of methane oxidation were calculated on the basis of oxic incubations by using the anoxic emissions as an estimate of the maximum potential flux. This technique indicated that methane oxidation consumed up to 91% of the maximum potential flux in peat sediments but that oxidation was negligible in marl sediments. Oxygen microprofiles determined for intact cores were comparable to profiles measured in situ. Thus, the laboratory incubations appeared to provide a reasonable approximation of in situ activities. This was further supported by the agreement between measured methane fluxes and fluxes predicted on the basis of methane profiles determined by in situ sampling of pore water. Methane emissions from peat sediments, oxygen concentrations and penetration depths, and methane concentration profiles were all sensitive to light-dark shifts as determined by a combination of field and laboratory analyses. Methane emissions were lower and oxygen concentrations and penetration depths were higher under illuminated than under dark conditions; the profiles of methane concentration changed in correspondence to the changes in oxygen profiles, but the estimated flux of methane into the oxic zone changed negligibly. Sediment-free, root-associated methane oxidation showed a pattern similar to that for methane oxidation in the core analyses: no oxidation was detected for roots growing in marl sediment, even for roots of Cladium jamaicense, which had the highest activity for samples from peat sediments. The magnitude of the root-associated oxidation rates indicated that belowground plant surfaces may not markedly increase the total capacity for methane consumption. However, the data collectively support the notion that the distribution and activity of methane oxidation have a major impact on the magnitude of atmospheric fluxes from the Everglades. PMID:16348299

Organic carbon burial in fjords: Terrestrial versus marine inputs

NASA Astrophysics Data System (ADS)

Cui, Xingqian; Bianchi, Thomas S.; Savage, Candida; Smith, Richard W.

2016-10-01

Fjords have been identified as sites of enhanced organic carbon (OC) burial and may play an important role in regulating climate change on glacial-interglacial timescales. Understanding sediment processes and sources of sedimentary OC are necessary to better constrain OC burial in fjords. In this study, we use Fiordland, New Zealand, as a case study and present data on surface sediments, sediment down-cores and terrestrial end-members to examine dynamics of sediments and the sources of OC in fjord sediments. Sediment cores showed evidence of multiple particle sources, frequent bioturbation and mass-wasting events. A multi-proxy approach (stable isotopes, lignin-phenols and fatty acids) allowed for separation of marine, soil and vascular plant OC in surface sediments. The relationship between mass accumulation rate (MAR) and OC contents in fjord surface sediments suggested that mineral dilution is important in controlling OC content on a global scale, but is less important for specific regions (e.g., New Zealand). The inconsistency of OC budgets calculated by using MAR weighted %OC and OC accumulation rates (AR; 6 vs 21-31 Tg OC yr-1) suggested that sediment flux in fjords was likely underestimated. By using end-member models, we propose that 55% to 62% of total OC buried in fjords is terrestrially derived, and accounts for 17 ± 12% of the OCterr buried in all marine sediments. The strong correlation between MAR and OC AR indicated that OC flux will likely decrease in fjords in the future with global warming due to decrease in sediment flux caused by glacier denudation.

Sediment DIN fluxes and preferential recycling of benthic microalgal nitrogen in a shallow macrotidal estuary

USGS Publications Warehouse

Tobias, C.; Giblin, A.; McClelland, J.; Tucker, J.; Peterson, B.

2003-01-01

Sediment-water fluxes of NH4+, NO3-, dissolved inorganic carbon, and O2 were measured in cores collected from the upper Rowley River estuary, Massachusetts, and used to calculate rates of organic nitrogen (N) mineralization, nitrification, and coupled and direct denitrification (DNF). The cores contained 15N label in benthic microalgae (BMA) and in NO3- in the overlying water as a result of an ongoing whole-estuary 15NO 3- enrichment study (NISOTREX II). The tracer allowed for estimation of gross NO3- regeneration in sediments and the contribution of BMA derived N to total mineralization. The mean mineralization rate between sites was 16.0 ?? 2.0 mmol N m-2 d-1. Approximately 13 to 56% of the mineralized N was nitrified at rates ranging from 1.8 to 10.1 mmol N m-2 d-1. Total denitrification was dominated by direct DNF (3.6 mmol N m-2 d -1) furthest upstream, where NO3- concentrations were highest. Coupled DNF was most important (8.0 mmol N m -2 d-1) in the sediments with high nitrification and low water column NO3-. A gross NO3- flux from sediments to water of 0.9 to 2.1 mmol N m-2 d-1 was estimated from the isotope dilution of ??15NO 3- in the overlying water of the cores. The isotope dilution seen in the cores was also detected as a deviation from conservative ??15NO3- mixing along estuarine transects. Incorporation of this NO3- regeneration into the DNF calculations effectively increased the estimate of direct DNF by up to 50% and decreased the coupled DNF estimate by up to 220%. Increasing ?? 15NH4+ in the water of the cores indicated that the 15N-labelled BMA were preferentially mineralized over bulk sediment organic N. Additional 15N enrichments in the sediment bacterial biomarker diaminopimelic acid showed a link among 15N-labeled BMA, active bacteria, and 15NH 4+released to the overlying water. Based on ?? 15NH4+ enrichments in the cores, BMA accounted for approximately 50 to 100% of the N mineralized. An isotopic enrichment of ??15NH4+ above background in the estuary was observed at a magnitude consistent with the core-based rates of BMA mineralization. These results provide further evidence that BMA are not unidirectional sinks for water column-dissolved organic nitrogen, but instead act to turn over N between sediments and estuarine water on the scale of days.

Southern Appalachian hillslope erosion rates measured by soil and detrital radiocarbon in hollows

USGS Publications Warehouse

Hales, T.C.; Scharer, K.M.; Wooten, R.M.

2012-01-01

Understanding the dynamics of sediment generation and transport on hillslopes provides important constraints on the rate of sediment output from orogenic systems. Hillslope sediment fluxes are recorded by organic material found in the deposits infilling unchanneled convergent topographic features called hollows. This study describes the first hollow infilling rates measured in the southern Appalachian Mountains. Infilling rates (and bedrock erosion rates) were calculated from the vertical distribution of radiocarbon ages at two sites in the Coweeta drainage basin, western North Carolina. At each site we dated paired charcoal and silt soil organic matter samples from five different horizons. Paired radiocarbon samples were used to bracket the age of the soil material in order to capture the range of complex soil forming processes and deposition within the hollows. These dates constrain hillslope erosion rates of between 0.051 and 0.111mmyr-1. These rates are up to 4 times higher than spatially-averaged rates for the Southern Appalachian Mountains making creep processes one of the most efficient erosional mechanisms in this mountain range. Our hillslope erosion rates are consistent with those of forested mountain ranges in the western United States, suggesting that the mechanisms (dominantly tree throw) driving creep erosion in both the western United States and the Southern Appalachian Mountains are equally effective. ?? 2011 Elsevier B.V.

Climate-driven unsteady denudation and sediment flux in a high-relief unglaciated catchment-fan using 26Al and 10Be: Panamint Valley, California

NASA Astrophysics Data System (ADS)

Mason, Cody C.; Romans, Brian W.

2018-06-01

Environmental changes within erosional catchments of sediment routing systems are predicted to modulate sediment transfer dynamics. However, empirical and numerical models that predict such phenomena are difficult to test in natural systems over multi-millennial timescales. Tectonic boundary conditions and climate history in the Panamint Range, California, are relatively well-constrained by existing low-temperature thermochronology and regional multi-proxy paleoclimate studies, respectively. Catchment-fan systems present there minimize sediment storage and recycling, offering an excellent natural laboratory to test models of climate-sedimentary dynamics. We used stratigraphic characterization and cosmogenic radionuclides (CRNs; 26Al and 10Be) in the Pleasant Canyon complex (PCC), a linked catchment-fan system, to examine the effects of Pleistocene high-magnitude, high-frequency climate change on CRN-derived denudation rates and sediment flux in a high-relief, unglaciated catchment-fan system. Calculated 26Al/10Be burial ages from 13 samples collected in an ∼180 m thick outcropping stratigraphic succession range from ca. 1.55 ± 0.22 Ma in basal strata, to ca. 0.36 ± 0.18-0.52 ± 0.20 Ma within the uppermost part of the succession. The mean long-term CRN-derived paleodenudation rate, 36 ± 8 mm/kyr (1σ), is higher than the modern rate of 24 ± 0.6 mm/kyr from Pleasant Canyon, and paleodenudation rates during the middle Pleistocene display some high-frequency variability in the high end (up to 54 ± 10 mm/kyr). The highest CRN-derived denudation rates are associated with stratigraphic evidence for increased precipitation during glacial-pluvial events after the middle Pleistocene transition (post ca. 0.75 Ma), suggesting 100 kyr Milankovitch periodicity could drive the observed variability. We investigated the potential for non-equilibrium sedimentary processes, i.e. increased landslides or sediment storage/recycling, to influence apparent paleodenudation rates; end-member mixing models suggest that a mixture of >50% low-CRN-concentration sediment from landslides is required to produce the largest observed increase in paleodenudation rate. The overall pattern of CRN-derived burial ages, paleodenudation rates, and stratigraphic facies suggests Milankovitch timescale climate transitions drive variability in catchment denudation rates and sediment flux, or alternatively that climate transitions affect sedimentary process regimes that result in measurable variability of CRN concentrations in unglaciated catchment-fan systems.

Cenozoic North American Drainage Basin Evolution, Sediment Yield, and Accumulation in the Gulf of Mexico Basin

NASA Astrophysics Data System (ADS)

Galloway, W.; Ganey-Curry, P. E.

2010-12-01

The Cenozoic fill of the Gulf of Mexico basin contains a continuous record of sediment supply from the North American continental interior for the past 65 million years. Regional mapping of unit thickness and paleogeography for 18 depositional episodes defines patterns of shifting entry points of continental fluvial systems and quantifies the total volume of sediment supplied during each episode. Eight fluvio-deltaic depocenters, named for geographic similarities to entry points and drainage basins of modern rivers, are present. From southwest to northeast, they are the Rio Bravo, Rio Grande, Guadalupe, Colorado, Houston-Brazos, Red, Mississippi, and Tennessee axes. Sediment volume was calculated from hand-contoured unit thickness maps compiled from basin-wide well and seismic control. Using a GIS algorithm to sum volumes within polygons bounding interpreted North American river contribution, the total extant volume was then calculated. General compaction factors were used to convert modern volume to quantitative approximations of total grain volume. Grain volume rate of supply for each depositional episode was then calculated. Values vary by more than an order of magnitude. Supply rate has commonly varied by two-fold or more between successive depositional episodes. Sediment supply is a significant, independent variable in development of stratigraphic sequences within the Gulf basin. Paleogeographic maps of the continental interior for eleven Cenozoic time intervals display the evolving and complex interplay of intracontinental tectonism, climate change, and drainage basin evolution. Five tectono-climatic eras are differentiated: Paleocene late Laramide era; early to middle Eocene terminal Laramide era; middle Cenozoic (Late Eocene—Early Miocene) dry, volcanogenic era; middle Neogene (Middle—Late Miocene) arid, extensional era; and late Neogene (Plio—Pleistocene) monsoonal, epeirogenic uplift era. Sediment supply to the GOM reflects the interplay of (1) areal extent of river drainage basins, (2) source area relief, (3) climate of the source areas and tributary systems, (4) source lithology, and (5) sediment storage within the upper drainage basin. Climate has played an important and complex role in modulating supply. In wet tropical to temperate climate regimes, abundant runoff efficiently removed entrained sediment. Arid climate limited runoff; resultant transport-limited tributaries and trunk streams deposited aggradational alluvial aprons, storing sediment in the drainage basin even in the absence of a structural depression. Eolian deposition commonly accompanied such alluvial aggradation. In contrast, seasonality and consequent runoff variability favored erosion and efficient sediment evacuation from the upper parts of drainage basins. Tectonism has played a prominent but equally complex role. Elevation of uplands by compression, crustal heating, or extrusive volcanism created primary loci of erosion and high sediment yield. At the same time, accompanying subsidence sometimes created long-lived sediment repositories that intercepted and sequestered sediment adjacent to sources. Regional patterns of uplift and subsidence relocated drainage divides and redirected trunk stream paths to the Gulf margin.

Mercury cycling in stream ecosystems. 2. Benthic methylmercury production and bed sediment-pore water partitioning.

PubMed

Marvin-Dipasquale, Mark; Lutz, Michelle A; Brigham, Mark E; Krabbenhoft, David P; Aiken, George R; Orem, William H; Hall, Britt D

2009-04-15

Mercury speciation, controls on methylmercury (MeHg) production, and bed sediment-pore water partitioning of total Hg (THg) and MeHg were examined in bed sediment from eight geochemically diverse streams where atmospheric deposition was the predominant Hg input. Across all streams, sediment THg concentrations were best described as a combined function of sediment percent fines (%fines; particles < 63 microm) and organic content. MeHg concentrations were best described as a combined function of organic content and the activity of the Hg(II)-methylating microbial community and were comparable to MeHg concentrations in streams with Hg inputs from industrial and mining sources. Whole sediment tin-reducible inorganic reactive Hg (Hg(II)R) was used as a proxy measure for the Hg(II) pool available for microbial methylation. In conjunction with radiotracer-derived rate constants of 203Hg(II) methylation, Hg(II)R was used to calculate MeHg production potential rates and to explain the spatial variability in MeHg concentration. The %Hg(II)R (of THg) was low (2.1 +/- 5.7%) and was inversely related to both microbial sulfate reduction rates and sediment total reduced sulfur concentration. While sediment THg concentrations were higher in urban streams, %MeHg and %Hg(II)R were higher in nonurban streams. Sediment pore water distribution coefficients (log Kd's) for both THg and MeHg were inversely related to the log-transformed ratio of pore water dissolved organic carbon (DOC) to bed sediment %fines. The stream with the highest drainage basin wetland density also had the highest pore water DOC concentration and the lowest log Kd's for both THg and MeHg. No significant relationship existed between overlying water MeHg concentrations and those in bed sediment or pore water, suggesting upstream sources of MeHg production may be more important than local streambed production as a driver of water column MeHg concentration in drainage basins that receive Hg inputs primarily from atmospheric sources.

Observations at convergent margins concerning sediment subduction, subduction erosion, and the growth of continental crust

USGS Publications Warehouse

von Huene, Roland E.; Scholl, D. W.

1991-01-01

At ocean margins where two plates converge, the oceanic plate sinks or is subducted beneath an upper one topped by a layer of terrestrial crust. This crust is constructed of continental or island arc material. The subduction process either builds juvenile masses of terrestrial crust through arc volcanism or new areas of crust through the piling up of accretionary masses (prisms) of sedimentary deposits and fragments of thicker crustal bodies scraped off the subducting lower plate. At convergent margins, terrestrial material can also bypass the accretionary prism as a result of sediment subduction, and terrestrial matter can be removed from the upper plate by processes of subduction erosion. Sediment subduction occurs where sediment remains attached to the subducting oceanic plate and underthrusts the seaward position of the upper plate's resistive buttress (backstop) of consolidated sediment and rock. Sediment subduction occurs at two types of convergent margins: type 1 margins where accretionary prisms form and type 2 margins where little net accretion takes place. At type 2 margins (???19,000 km in global length), effectively all incoming sediment is subducted beneath the massif of basement or framework rocks forming the landward trench slope. At accreting or type 1 margins, sediment subduction begins at the seaward position of an active buttress of consolidated accretionary material that accumulated in front of a starting or core buttress of framework rocks. Where small-to-mediumsized prisms have formed (???16,300 km), approximately 20% of the incoming sediment is skimmed off a detachment surface or decollement and frontally accreted to the active buttress. The remaining 80% subducts beneath the buttress and may either underplate older parts of the frontal body or bypass the prism entirely and underthrust the leading edge of the margin's rock framework. At margins bordered by large prisms (???8,200 km), roughly 70% of the incoming trench floor section is subducted beneath the frontal accretionary body and its active buttress. In rounded figures the contemporary rate of solid-volume sediment subduction at convergent ocean margins (???43,500 km) is calculated to be 1.5 km3/yr. Correcting type 1 margins for high rates of terrigenous seafloor sedimentation during the past 30 m.y. or so sets the long-term rate of sediment subduction at 1.0 km3/yr. The bulk of the subducted material is derived directly or indirectly from continental denudation. Interstitial water currently expulsed from accreted and deeply subducted sediment and recycled to the ocean basins is estimated at 0.9 km3/yr. The thinning and truncation caused by subduction erosion of the margin's framework rock and overlying sedimentary deposits have been demonstrated at many convergent margins but only off northern Japan, central Peru, and northern Chile has sufficient information been collected to determine average or long-term rates, which range from 25 to 50 km3/m.y. per kilometer of margin. A conservative long-term rate applicable to many sectors of convergent margins is 30 km3/km/m.y. If applied to the length of type 2 margins, subduction erosion removes and transports approximately 0.6 km3/yr of upper plate material to greater depths. At various places, subduction erosion also affects sectors of type 1 margins bordered by small- to medium-sized accretionary prisms (for example, Japan and Peru), thus increasing the global rate by possibly 0.5 km3/yr to a total of 1.1 km3/yr. Little information is available to assess subduction erosion at margins bordered by large accretionary prisms. Mass balance calculations allow assessments to be made of the amount of subducted sediment that bypasses the prism and underthrusts the margin's rock framework. This subcrustally subducted sediment is estimated at 0.7 km3/yr. Combined with the range of terrestrial matter removed from the margin's rock framework by subduction erosion, the global volume of subcrustally subducted materia

Mapping spatial patterns of stream power and channel change along a gravel-bed river in northern Yellowstone

NASA Astrophysics Data System (ADS)

Lea, Devin M.; Legleiter, Carl J.

2016-01-01

Stream power represents the rate of energy expenditure along a river and can be calculated using topographic data acquired via remote sensing or field surveys. This study sought to quantitatively relate temporal changes in the form of Soda Butte Creek, a gravel-bed river in northeastern Yellowstone National Park, to stream power gradients along an 8-km reach. Aerial photographs from 1994 to 2012 and ground-based surveys were used to develop a locational probability map and morphologic sediment budget to assess lateral channel mobility and changes in net sediment flux. A drainage area-to-discharge relationship and DEM developed from LiDAR data were used to obtain the discharge and slope values needed to calculate stream power. Local and lagged relationships between mean stream power gradient at median peak discharge and volumes of erosion, deposition, and net sediment flux were quantified via spatial cross-correlation analyses. Similarly, autocorrelations of locational probabilities and sediment fluxes were used to examine spatial patterns of sediment sources and sinks. Energy expended above critical stream power was calculated for each time period to relate the magnitude and duration of peak flows to the total volumetric change in each time increment. Collectively, we refer to these methods as the stream power gradient (SPG) framework. The results of this study were compromised by methodological limitations of the SPG framework and revealed some complications likely to arise when applying this framework to small, wandering, gravel-bed rivers. Correlations between stream power gradients and sediment flux were generally weak, highlighting the inability of relatively simple statistical approaches to link sub-budget cell-scale sediment dynamics to larger-scale driving forces such as stream power gradients. Improving the moderate spatial resolution techniques used in this study and acquiring very-high resolution data from recently developed methods in fluvial remote sensing could help improve understanding of the spatial organization of stream power, sediment transport, and channel change in dynamic natural rivers.

Mapping spatial patterns of stream power and channel change along a gravel-bed river in northern Yellowstone

NASA Astrophysics Data System (ADS)

Lea, Devin M.

Stream power represents the rate of energy expenditure along a river and can be calculated using topographic data acquired via remote sensing or field surveys. This study used remote sensing and GIS tools along with field data to quantitatively relate temporal changes in the form of Soda Butte Creek, a gravel-bed river in northeastern Yellowstone National Park, to stream power gradients along an 8 km reach. Aerial photographs from 1994-2012 and cross-section surveys were used to develop a locational probability map and morphologic sediment budget to assess lateral channel mobility and changes in net sediment flux. A drainage area-to-discharge relationship and digital elevation model (DEM) developed from light detection and ranging (LiDAR) data were used to obtain the discharge and slope values needed to calculate stream power. Local and lagged relationships between mean stream power gradient at median peak discharge and volumes of erosion, deposition, and net sediment flux were quantified via spatial cross-correlation analyses. Similarly, autocorrelations of locational probabilities and sediment fluxes were used to examine spatial patterns of sediment sources and sinks. Energy expended above critical stream power was calculated for each time period to relate the magnitude and duration of peak flows to the total volumetric change in each time increment. Results indicated a lack of strong correlation between stream power gradients and sediment response, highlighting the geomorphic complexity of Soda Butte Creek and the inability of relatively simple statistical approaches to link sub-budget cell-scale sediment dynamics to larger-scale driving forces such as stream power gradients. Improving the moderate spatial resolution techniques used in this study and acquiring very-high resolution data from recently developed methods in fluvial remote sensing could help improve understanding of the spatial organization of stream power, sediment transport, and channel change in dynamic natural rivers.

An approach for modeling sediment budgets in supply-limited rivers

USGS Publications Warehouse

Wright, Scott A.; Topping, David J.; Rubin, David M.; Melis, Theodore S.

2010-01-01

Reliable predictions of sediment transport and river morphology in response to variations in natural and human-induced drivers are necessary for river engineering and management. Because engineering and management applications may span a wide range of space and time scales, a broad spectrum of modeling approaches has been developed, ranging from suspended-sediment "rating curves" to complex three-dimensional morphodynamic models. Suspended sediment rating curves are an attractive approach for evaluating changes in multi-year sediment budgets resulting from changes in flow regimes because they are simple to implement, computationally efficient, and the empirical parameters can be estimated from quantities that are commonly measured in the field (i.e., suspended sediment concentration and water discharge). However, the standard rating curve approach assumes a unique suspended sediment concentration for a given water discharge. This assumption is not valid in rivers where sediment supply varies enough to cause changes in particle size or changes in areal coverage of sediment on the bed; both of these changes cause variations in suspended sediment concentration for a given water discharge. More complex numerical models of hydraulics and morphodynamics have been developed to address such physical changes of the bed. This additional complexity comes at a cost in terms of computations as well as the type and amount of data required for model setup, calibration, and testing. Moreover, application of the resulting sediment-transport models may require observations of bed-sediment boundary conditions that require extensive (and expensive) observations or, alternatively, require the use of an additional model (subject to its own errors) merely to predict the bed-sediment boundary conditions for use by the transport model. In this paper we present a hybrid approach that combines aspects of the rating curve method and the more complex morphodynamic models. Our primary objective was to develop an approach complex enough to capture the processes related to sediment supply limitation but simple enough to allow for rapid calculations of multi-year sediment budgets. The approach relies on empirical relations between suspended sediment concentration and discharge but on a particle size specific basis and also tracks and incorporates the particle size distribution of the bed sediment. We have applied this approach to the Colorado River below Glen Canyon Dam (GCD), a reach that is particularly suited to such an approach because it is substantially sediment supply limited such that transport rates are strongly dependent on both water discharge and sediment supply. The results confirm the ability of the approach to simulate the effects of supply limitation, including periods of accumulation and bed fining as well as erosion and bed coarsening, using a very simple formulation. Although more empirical in nature than standard one-dimensional morphodynamic models, this alternative approach is attractive because its simplicity allows for rapid evaluation of multi-year sediment budgets under a range of flow regimes and sediment supply conditions, and also because it requires substantially less data for model setup and use.

Mercury methylation and demethylation in Hg-contaminated lagoon sediments (Marano and Grado Lagoon, Italy)

NASA Astrophysics Data System (ADS)

Hines, Mark E.; Poitras, Erin N.; Covelli, Stefano; Faganeli, Jadran; Emili, Andrea; Žižek, Suzana; Horvat, Milena

2012-11-01

Mercury (Hg) transformation activities and sulfate (SO42-) reduction were studied in sediments of the Marano and Grado Lagoons in the Northern Adriatic Sea region as part of the "MIRACLE" project. The lagoons, which are sites of clam (Tapes philippinarum) farming, have been receiving excess Hg from the Isonzo River for centuries. Marano Lagoon is also contaminated from a chlor-alkali plant. Radiotracer methods were used to measure mercury methylation (230Hg, 197Hg), methylmercury (MeHg) demethylation (14C-MeHg) and SO42- reduction (35S) in sediment cores collected in autumn, winter and summer. Mercury methylation rate constants ranged from near zero to 0.054 day-1, generally decreased with depth, and were highest in summer. Demethylation rate constants were much higher than methylation reaching values of ˜0.6 day-1 in summer. Demethylation occurred via the oxidative pathway, except in winter when the reductive pathway increased in importance in surficial sediments. Sulfate reduction was also most active in summer (up to 1600 nmol mL-1 day-1) and depth profiles reflected seasonally changing redox conditions near the surface. Methylation and demethylation rate constants correlated positively with SO42- reduction and pore-water Hg concentrations, and inversely with Hg sediment-water partition coefficients indicating the importance of SO42- reduction and Hg dissolution on Hg cycling. Hg transformation rates were calculated using rate constants and concentrations of Hg species. In laboratory experiments, methylation was inhibited by amendments of the SO42--reduction inhibitor molybdate and by nitrate. Lagoon sediments displayed a dynamic seasonal cycle in which Hg dissolution in spring/summer stimulated Hg methylation, which was followed by a net loss of MeHg in autumn from demethylation. Sulfate-reducing bacteria (SRB) tended to be responsible for methylation of Hg and the oxidative demethylation of MeHg. However, during winter in surficial sediments, iron-reducing bacteria seemed to contribute to methylation and Hg-resistant bacteria increased in importance in the reductive demethylation of MeHg. The high rates of MeHg demethylation in lagoon sediments may diminish the accumulation of MeHg.

Nitrogen reduction pathways in estuarine sediments: Influences of organic carbon and sulfide

NASA Astrophysics Data System (ADS)

Plummer, Patrick; Tobias, Craig; Cady, David

2015-10-01

Potential rates of sediment denitrification, anaerobic ammonium oxidation (anammox), and dissimilatory nitrate reduction to ammonium (DNRA) were mapped across the entire Niantic River Estuary, CT, USA, at 100-200 m scale resolution consisting of 60 stations. On the estuary scale, denitrification accounted for ~ 90% of the nitrogen reduction, followed by DNRA and anammox. However, the relative importance of these reactions to each other was not evenly distributed through the estuary. A Nitrogen Retention Index (NIRI) was calculated from the rate data (DNRA/(denitrification + anammox)) as a metric to assess the relative amounts of reactive nitrogen being recycled versus retained in the sediments following reduction. The distribution of rates and accompanying sediment geochemical analytes suggested variable controls on specific reactions, and on the NIRI, depending on position in the estuary and that these controls were linked to organic carbon abundance, organic carbon source, and pore water sulfide concentration. The relationship between NIRI and organic carbon abundance was dependent on organic carbon source. Sulfide proved the single best predictor of NIRI, accounting for 44% of its observed variance throughout the whole estuary. We suggest that as a single metric, sulfide may have utility as a proxy for gauging the distribution of denitrification, anammox, and DNRA.

Sediment storage quantification and postglacial evolution of an inner-alpine sedimentary basin (Gradenmoos, Schober Mountains, Austria)

NASA Astrophysics Data System (ADS)

Götz, J.; Buckel, J.; Otto, J. C.; Schrott, L.

2012-04-01

Knickpoints in longitudinal valley profiles of alpine headwater catchments can be frequently assigned to the lithological and tectonical setting, to damming effects through large (rockfall) deposits, or to the impact of Pleistocene glaciations causing overdeepened basins. As a consequence various sedimentary sinks developed, which frequently interrupt sediment flux in alpine drainage basins. Today these locations may represent landscape archives documenting a sedimentary history of great value for the understanding of alpine landscape evolution. The glacially overdeepened Gradenmoos basin at 1920 m a.s.l. (an alpine lake mire with adjacent floodplain deposits and surrounding slope storage landforms; approx. 4.1 km2) is the most pronounced sink in the studied Gradenbach catchment (32.5 km2). The basin is completely filled up with sediments delivered by mainly fluvial processes, debris flows, and rock falls, it is assumed to be deglaciated since Egesen times and it is expected to archive a continuous stratigraphy of postglacial sedimentation. As the analysis of denudation-accumulation-systems is generally based on back-calculation of stored sediment volumes to a specific sediment delivering area, most reliable results will be consequently obtained (1) if sediment output of the system can be neglected for the investigated period of time, (2) if - due to spatial scale - sediment storage can be assessed quantitatively with a high level of accuracy, and (3) if the sediment contributing area can be clearly delimited. All three aspects are considered to be fulfilled to a high degree within the Gradenmoos basin. Sediment storage is quantified using geophysical methods, core drillings and GIS modelling whereas postglacial reconstruction is based on radiocarbon dating and palynological analyses. Subject to variable subsurface conditions, different geophysical methods were applied to detect bedrock depth. Electrical resistivity surveying (2D/3D) was used most extensively as it delivered detailed and realistic subsurface models with low residual errors in the fine grained and water saturated central and distal part of the basin. With a lower data density, ground penetrating radar and refraction seismic supplied bedrock depths underneath adjacent debris and talus slope deposits. Additionally extracted sediment cores (up to 22 m depth) yielded a detailed stratigraphic record of the basin comprising a basal till layer underneath lake sediments (sandy-silty, partly varved), a sandy matrix with several oxidised layers in the upper sections, and layers of peat towards the surface. As bedrock was reached several times, core drilling further enabled to calibrate resistivity models. On the base of geophysical derived bedrock points, the shape of the assumed bedrock basin was modelled using a thin-plate-spline interpolation. Sediment volumes were calculated by subtracting the bedrock model from a surface DEM derived from terrestrial laser scanning. Since sediment delivering areas can be clearly assigned to single storage landform volumes, denudation rates could be calculated in detail and related to sedimentation rates obtained by radiocarbon dating results. An integrated analysis of surface, subsurface and temporal information finally yielded a model of postglacial basin evolution which will be discussed in a paraglacial context. This presentation is supported by the EUROCORES programme TOPO-EUROPE of the European Science Foundation.

Burrows of the semi-terrestrial crab Ucides cordatus enhance CO2 release in a North Brazilian mangrove forest.

PubMed

Pülmanns, Nathalie; Diele, Karen; Mehlig, Ulf; Nordhaus, Inga

2014-01-01

Ucides cordatus is an abundant mangrove crab in Brazil constructing burrows of up to 2 m depth. Sediment around burrows may oxidize during low tides. This increase in sediment-air contact area may enhance carbon degradation processes. We hypothesized that 1) the sediment CO2 efflux rate is greater with burrows than without and 2) the reduction potential in radial profiles in the sediment surrounding the burrows decreases gradually, until approximating non-bioturbated conditions. Sampling was conducted during the North Brazilian wet season at neap tides. CO2 efflux rates of inhabited burrows and plain sediment were measured with a CO2/H2O gas analyzer connected to a respiration chamber. Sediment redox potential, pH and temperature were measured in the sediment surrounding the burrows at horizontal distances of 2, 5, 8 and 15 cm at four sediment depths (1, 10, 30 and 50 cm) and rH values were calculated. Sediment cores (50 cm length) were taken to measure the same parameters for plain sediment. CO2 efflux rates of plain sediment and individual crab burrows with entrance diameters of 7 cm were 0.7-1.3 µmol m(-2) s(-1) and 0.2-0.4 µmol burrows(-1) s(-1), respectively. CO2 released from a Rhizophora mangle dominated forest with an average of 1.7 U. cordatus burrows(-1) m(-2) yielded 1.0-1.7 µmol m(-2) s(-1), depending on the month and burrow entrance diameter. Laboratory experiments revealed that 20-60% of the CO2 released by burrows originated from crab respiration. Temporal changes in the reduction potential in the sediment surrounding the burrows did not influence the CO2 release from burrows. More oxidized conditions of plain sediment over time may explain the increase in CO2 release until the end of the wet season. CO2 released by U. cordatus and their burrows may be a significant pathway of CO2 export from mangrove sediments and should be considered in mangrove carbon budget estimates.

Burrows of the Semi-Terrestrial Crab Ucides cordatus Enhance CO2 Release in a North Brazilian Mangrove Forest

PubMed Central

Pülmanns, Nathalie; Diele, Karen; Mehlig, Ulf; Nordhaus, Inga

2014-01-01

Ucides cordatus is an abundant mangrove crab in Brazil constructing burrows of up to 2 m depth. Sediment around burrows may oxidize during low tides. This increase in sediment-air contact area may enhance carbon degradation processes. We hypothesized that 1) the sediment CO2 efflux rate is greater with burrows than without and 2) the reduction potential in radial profiles in the sediment surrounding the burrows decreases gradually, until approximating non-bioturbated conditions. Sampling was conducted during the North Brazilian wet season at neap tides. CO2 efflux rates of inhabited burrows and plain sediment were measured with a CO2/H2O gas analyzer connected to a respiration chamber. Sediment redox potential, pH and temperature were measured in the sediment surrounding the burrows at horizontal distances of 2, 5, 8 and 15 cm at four sediment depths (1, 10, 30 and 50 cm) and rH values were calculated. Sediment cores (50 cm length) were taken to measure the same parameters for plain sediment. CO2 efflux rates of plain sediment and individual crab burrows with entrance diameters of 7 cm were 0.7–1.3 µmol m−2 s−1 and 0.2–0.4 µmol burrows−1 s−1, respectively. CO2 released from a Rhizophora mangle dominated forest with an average of 1.7 U. cordatus burrows−1 m−2 yielded 1.0–1.7 µmol m−2 s−1, depending on the month and burrow entrance diameter. Laboratory experiments revealed that 20–60% of the CO2 released by burrows originated from crab respiration. Temporal changes in the reduction potential in the sediment surrounding the burrows did not influence the CO2 release from burrows. More oxidized conditions of plain sediment over time may explain the increase in CO2 release until the end of the wet season. CO2 released by U. cordatus and their burrows may be a significant pathway of CO2 export from mangrove sediments and should be considered in mangrove carbon budget estimates. PMID:25313661

Relative role of pore water versus ingested sediment in bioavailability of organic contaminants in marine sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forbes, T.L.; Hansen, R.; Kure, L.K.

Experimental data for fluoranthene and feeding selectivity in combination with reaction-diffusion modeling suggest that ingestion of contaminated sediment may often be the dominant uptake pathway for deposit-feeding invertebrates in sediments. A dietary absorption efficiency of 56% and accompanying forage ratio of 2.4 were measured using natural sediment that had been dual-labeled ({sup 14}C:{sup 51}Cr) with fluoranthene and fed to the marine deposit-feeding polychaete Capitella species I. Only 3 to 4% of the total absorption could be accounted for by desorption during gut passage. These data were then used as input into a reaction-diffusion model to calculate the importance of uptakemore » from ingested sediment relative to pore-water exposure. The calculations predict a fluoranthene dietary uptake flux that is 20 to 30 times greater than that due to pore water. Factors that act to modify or control the formation of local chemical gradients, boundary layers, or dietary absorption rates including particle selection or burrow construction will be important in determining the relative importance of potential exposure pathways. From a chemical perspective, the kinetics of the adsorption and desorption process are especially important as they will strongly influence the boundary layer immediately surrounding burrowing animals or irrigated tubes. The most important biological factors likely include irrigation behavior and burrow density and size.« less

Reconstructing depositional processes and history from reservoir stratigraphy: Englebright Lake, Yuba River, northern California

USGS Publications Warehouse

Snyder, N.P.; Wright, S.A.; Alpers, Charles N.; Flint, L.E.; Holmes, C.W.; Rubin, D.M.

2006-01-01

Reservoirs provide the opportunity to link watershed history with its stratigraphic record. We analyze sediment cores from a northern California reservoir in the context of hydrologic history, watershed management, and depositional processes. Observations of recent depositional patterns, sediment-transport calculations, and 137CS geochronology support a conceptual model in which the reservoir delta progrades during floods of short duration (days) and is modified during prolonged (weeks to months) drawdowns that rework topset beds and transport sand from topsets to foresets. Sediment coarser than 0.25-0.5 mm. deposits in foresets and topsets, and finer material falls out of suspension as bottomset beds. Simple hydraulic calculations indicate that fine sand (0.063-0.5 mm) is transported into the distal bottomset area only during floods. The overall stratigraphy suggests that two phases of delta building occurred in the reservoir. The first, from dam construction in 1940 to 1970, was heavily influenced by annual, prolonged >20 m drawdowns of the water level. The second, built on top of the first, reflects sedimentation from 1970 to 2002 when the influence of drawdowns was less. Sedimentation rates in the central part of the reservoir have declined ???25% since 1970, likely reflecting a combination of fewer large floods, changes in watershed management, and winnowing of stored hydraulic mining sediment. Copyright 2006 by the American Geophysical Union.

Biotransformation of dichlorodiphenyltrichloroethane in the benthic polychaete, Nereis succinea: quantitative estimation by analyzing the partitioning of chemicals between gut fluid and lipid.

PubMed

Wang, Fei; Pei, Yuan-yuan; You, Jing

2015-02-01

Biotransformation plays an important role in the bioaccumulation and toxicity of a chemical in biota. Dichlorodiphenyltrichloroethane (DDT) commonly co-occurs with its metabolites (dichlorodiphenyldichloroethane [DDD] and dichlorodiphenyldichloroethylene [DDE]), in the environment; thus it is a challenge to accurately quantify the biotransformation rates of DDT and distinguish the sources of the accumulated metabolites in an organism. The present study describes a method developed to quantitatively analyze the biotransformation of p,p'-DDT in the benthic polychaete, Nereis succinea. The lugworms were exposed to sediments spiked with DDT at various concentrations for 28 d. Degradation of DDT to DDD and DDE occurred in sediments during the aging period, and approximately two-thirds of the DDT remained in the sediment. To calculate the biotransformation rates, residues of individual compounds measured in the bioaccumulation testing (after biotransformation) were compared with residues predicted by analyzing the partitioning of the parent and metabolite compounds between gut fluid and tissue lipid (before biotransformation). The results suggest that sediment ingestion rates decreased when DDT concentrations in sediment increased. Extensive biotransformation of DDT occurred in N. succinea, with 86% of DDT being metabolized to DDD and <2% being transformed to DDE. Of the DDD that accumulated in the lugworms, approximately 70% was the result of DDT biotransformation, and the remaining 30% was from direct uptake of sediment-associated DDD. In addition, the biotransformation was not dependent on bulk sediment concentrations, but rather on bioaccessible concentrations of the chemicals in sediment, which were quantified by gut fluid extraction. The newly established method improved the accuracy of prediction of the bioaccumulation and toxicity of DDTs. © 2014 SETAC.

Fault slip rates in the modern new madrid seismic zone

PubMed

Mueller; Champion; Guccione; Kelson

1999-11-05

Structural and geomorphic analysis of late Holocene sediments in the Lake County region of the New Madrid seismic zone indicates that they are deformed by fault-related folding above the blind Reelfoot thrust fault. The widths of narrow kink bands exposed in trenches were used to model the Reelfoot scarp as a forelimb on a fault-bend fold; this, coupled with the age of folded sediment, yields a slip rate on the blind thrust of 6.1 +/- 0.7 mm/year for the past 2300 +/- 100 years. An alternative method used structural relief across the scarp and the estimated dip of the underlying blind thrust to calculate a slip rate of 4.8 +/- 0.2 mm/year. Geometric relations suggest that the right lateral slip rate on the New Madrid seismic zone is 1.8 to 2.0 mm/year.

APPLICATIONS FOR DNA PROBES IN BIODEGRADATION RESEARCH

EPA Science Inventory

The use of DNA:DNA hybridization technology in biodegradation studies is investigated. The rate constants for sediments exposed to synthetic oils could be calculated from the NAH(1+) genotypes and this approach would be useful in predicting the kinetics of aromatic hydrocarbon de...

Methane distribution and transportation in Lake Chaohu: a shallow eutrophic lake in Eastern China

NASA Astrophysics Data System (ADS)

Zhang, L.; Shen, Q.

2016-12-01

Global warming and eutrophication are two world widely concerned environmental problems. Methane is the second important greenhouse gas, and lake has been proven as a quite important natural source of methane emission. More methane may emit from eutrophic lake due to the higher organic matter deposition in the lake sediment. Lake Chaohu is a large and shallow eutrophic lake in eastern China (N31°25' 31°43', E117°16' 117°05'), with an area of 770 km2 and a mean depth of 2.7 m. To examine methane distribution and transportation in this eutrophic lake, field study across different seasons was carried out with 20 study sites in the lake. Samples from the different water and sediment depth was collected using headspace bottle, and methane content was measured by gas chromatography using a flame ionization detector. The potential methane production in the sediment was examined by an indoor incubation experiment. Methane flux from sediment to the overlying water was calculated by Fick's law, and methane emission from surface to the air was calculated at the same time. The results indicates that more methane accumulated in the water of northwestern bay in this lake, and higher methane release rates was also found at this area. Methane increases gradually with depth in the top 10 cm in sediment cores, then it almost keeps at constant state in the deeper sediment. In the sediment from northwestern bay, more methane content and the higher potential methane production was found compared to the sediment from the east area of this lake.

Distribution and transport of polychlorinated biphenyls in Little Lake Butte des Morts, Fox River, Wisconsin, April 1987-October 1988

USGS Publications Warehouse

House, L.B.

1995-01-01

The mass of PCB's transported from the lake in streamflow during 1987-88 was calculated to be 110 kilograms annually. The PCB's transport rate decreased 50 percent from 1987 to 1988, for the period April through September. Transport of PCB's was greatest during April and May of each year. The average flux rate of PCB's into the water column from the bottom sediment in the lake was estimated to be 1.2 milligrams per square meter per day. The PCB's load seems to increase at river discharges greater than 212 cubic meters per second. This increase in PCB's load might be caused by resuspension of PCB's-contaminated bottom-sediment deposits. There was little variation in PCB's load at flows less than 170 cubic meters per second. The bottom sediments are a continuing source of PCB's to Little Lake Butte des Morts and the lower Fox River.

Bacteria in deep coastal plain sediments of Maryland: A possible source of CO2 to groundwater

NASA Astrophysics Data System (ADS)

Chapelle, Francis H.; Zelibor, Joseph L., Jr.; Grimes, D. Jay; Knobel, Leroy L.

1987-08-01

Nineteen cores of unconsolidated Coastal Plain sediments obtained from depths of 14 to 182 m below land surface near Waldorf, Maryland, were collected and examined for metabolically active bacteria. The age of the sediments cored range from Miocene to Early Cretaceous. Acridine orange direct counts of total (viable and nonviable) bacteria in core subsamples ranged from 108 to 104 bacteria/g of dry sediment. Direct counts of viable bacteria ranged from 106 to 103 bacteria/g of dry sediment. Three cores contained viable methanogenic bacteria, and seven cores contained viable sulfate-reducing bacteria. The observed presence of bacteria in these sediments suggest that heterotrophic bacterial metabolism, with lignitic organic material as the primary substrate, is a plausible source of CO2 to groundwater. However, the possibility that abiotic processes also produce CO2 cannot be ruled out. Estimated rates of CO2 production in the noncalcareous Magothy/Upper Patapsco and Lower Patapsco aquifers based on mass balance of dissolved inorganic carbon, groundwater flow rates, and flow path segment lengths are in the range 10-3 to 10-5 mmol L-1 yr-1. Isotope balance calculations suggest that aquifer-generated CO2 is much heavier isotopically (˜—10 to + 5 per mil) than lignite (˜-24 per mil) present in these sediments. This may reflect isotopic fractionation during methanogenesis and possibly other bacterially mediated processes.

Regional environmental change and human activity over the past hundred years recorded in the sedimentary record of Lake Qinghai, China.

PubMed

Sha, ZhanJiang; Wang, Qiugui; Wang, Jinlong; Du, Jinzhou; Hu, Jufang; Ma, Yujun; Kong, Fancui; Wang, Zhuan

2017-04-01

Environmental change and human activity can be recorded in sediment cores in aquatic systems such as lakes. Information from such records may be useful for environmental governance in the future. Six sediment cores were collected from Lake Qinghai, China and its sublakes during 2012 and 2013. Measurements of sediment grain-size fractions indicate that sedimentation in the north and southwest of Lake Qinghai is dominated by river input, whereas that in Lake Gahai and Lake Erhai is dominated by dunes. The sedimentation rates in Lake Qinghai were calculated to be 0.101-0.159 cm/y, similar to the rates in other lakes on the Qinghai-Tibetan Plateau. Using these data and sedimentation rates from the literature, we compiled the spatial distribution of sedimentation rates. Higher values were obtained in the three main areas of Lake Qinghai: two in river estuaries and one close to sand dunes. Lower values were measured in the center and south of the lake. Measurements of total organic carbon (TOC), total nitrogen (TN), phosphorus concentrations, and TOC/TN ratios in three cores (QH01, QH02, and Z04) revealed four horizons corresponding to times of increased human activity. These anthropogenic events were (1) the development of large areas of cropland in the Lake Qinghai watershed in 1960, (2) the beginning of nationwide fertilizer use and increases in cropland area in the lake watershed after 1970, (3) the implementation of the national program "Grain to Green," and (4) the rapid increase in the tourism industry from 2000. Profiles of Rb, Sr concentrations, the Rb/Sr ratio, and grain-size fraction in core Z04 indicate that the climate has become drier over the past 100 years. Therefore, we suggest that lake sediments such as those in Lake Qinghai are useful media for high-resolution studies of regional environmental change and human activity.

Long-term erosion rates of Panamanian drainage basins determined using in situ 10Be

NASA Astrophysics Data System (ADS)

Gonzalez, Veronica Sosa; Bierman, Paul R.; Nichols, Kyle K.; Rood, Dylan H.

2016-12-01

Erosion rates of tropical landscapes are poorly known. Using measurements of in situ-produced 10Be in quartz extracted from river and landslide sediment samples, we calculate long-term erosion rates for many physiographic regions of Panama. We collected river sediment samples from a wide variety of watersheds (n = 35), and then quantified 24 landscape-scale variables (physiographic, climatic, seismic, geologic, and land-use proxies) for each watershed before determining the relationship between these variables and long-term erosion rates using linear regression, multiple regression, and analysis of variance (ANOVA). We also used grain-size-specific 10Be analysis to infer the effect of landslides on the concentration of 10Be in fluvial sediment and thus on erosion rates. Cosmogenic 10Be-inferred, background erosion rates in Panama range from 26 to 595 m My- 1, with an arithmetic average of 201 m My- 1, and an area-weighted average of 144 m My- 1. The strongest and most significant relationship in the dataset was between erosion rate and silicate weathering rate, the mass of material leaving the basin in solution. None of the topographic variables showed a significant relationship with erosion rate at the 95% significance level; we observed weak but significant correlation between erosion rates and several climatic variables related to precipitation and temperature. On average, erosion rates in Panama are higher than other cosmogenically-derived erosion rates in tropical climates including those from Puerto Rico, Madagascar, Australia and Sri Lanka, likely the result of Panama's active tectonic setting and thus high rates of seismicity and uplift. Contemporary sediment yield and cosmogenically-derived erosion rates for three of the rivers we studied are similar, suggesting that human activities are not increasing sediment yield above long-term erosion rate averages in Panama. 10Be concentration is inversely proportional to grain size in landslide and fluvial samples from Panama; finer grain sizes from landslide material have lower 10Be concentration than fine-grained fluvial sediment. Large grains from both landslide and stream sediments have similarly low 10Be concentrations. These data suggest that fluvial gravel is delivered to the channel by landslides whereas sand is preferentially delivered by soil creep and bank collapse. Furthermore, the difference in 10Be concentration in sand-sized material delivered by soil creep and that delivered by landsliding suggests that the frequency and intensity of landslides influence basin scale erosion rates.

Sources of sediment to the coastal waters of the Southern California Bight

USGS Publications Warehouse

Warrick, J.A.; Farnsworth, K.L.

2009-01-01

The sources of sediment to the Southern California Bight were investigated with new calculations and published records of sediment fluxes, both natural and anthropogenic. We find that rivers are by far the largest source of sediment, producing over 10 ?? 106 t/yr on average, or over 80% of the sediment input to the Bight. This river flux is variable, however, over both space and time. The rivers draining the Transverse Ranges produce sediment at rates approximately an order of magnitude greater than the Peninsular Ranges (600-1500 t/km2/yr versus <90 t/km2/yr, respectively). Although the Transverse Range rivers represent only 23% of the total Southern California watershed drainage area, they are responsible for over 75% of the total sediment flux. River sediment flux is ephemeral and highly pulsed due to the semiarid climate and the influence of infrequent large storms. For more than 90% of the time, negligible amounts of sediment are discharged from the region's rivers, and over half of the post-1900 sediment load has been discharged during events with recurrence intervals greater than 10 yr. These rare, yet important, events are related to the El Ni??o-Southern Oscillation (ENSO), and the majority of sediment flux occurs during ENSO periods. Temporal trends in sediment discharge due to land-use changes and river damming are also observed. We estimate that there has been a 45% reduction in suspended-sediment flux due to the construction of dams. However, pre-dam sediment loads were likely artificially high due to the massive land-use changes of coastal California to rangeland during the nineteenth century. This increase in sediment production is observed in estuarine deposits throughout coastal California, which reveal that sedimentation rates were two to ten times higher during the nineteenth and twentieth centuries than during pre-European colonization. ?? 2009 The Geological Society of America.

Examining the Relationship Between Suspended Sand Load and Bedload on the Colorado River Using Concurrent Measurements of Suspended Sand and Observations of Sand Dune Migration.

NASA Astrophysics Data System (ADS)

Ashley, T.; McElroy, B. J.; Buscombe, D.; Grams, P. E.; Kaplinski, M. A.

2015-12-01

Spatial variability in sediment flux is directly related to geomorphic change. Along the Colorado River, measurements of sediment flux are used to track changes in sediment storage and time the release of controlled floods aimed at building eroded sandbars. The very high uncertainty typical of measurements of sediment flux has been reduced by a program of continuous measurement of suspended-sediment concentration by acoustic surrogates. However, there is still significant uncertainty in calculations of total flux. A large fraction of that uncertainty may be caused by overly simplified treatment of bedload flux, which is currently estimated as a constant 5% of the suspended sand flux. That constant is based on estimates of bedform migration rate made with side-scan sonar. Here, we apply theory which relates bedform migration and streamwise sediment flux, to bathymetric data collected at unprecedented temporal and spatial resolution adjacent to the USGS sediment monitoring station above Diamond Creek (362 km downstream from Lees Ferry, AZ). Quantitative time series measurements of reach averaged bedform transport are calculated and compared to fluxes estimated by expressing bedload as a constant fraction of suspended load. Over the range of discharges expected during normal dam operations, bedload transport estimated from the migration of bedforms in the study reach is at least 20% of instantaneous suspended sand load measured at the gage. While bedload appears to be controlled primarily by discharge (and therefore transport capacity of the flow), suspended sand load varies inversely with the grain size of suspended material, suggesting dependence on sediment supply. Sediment transport capacity can vary significantly at a given discharge depending on local hydraulic geometry, so it is likely that there is more spatial variability in bedload transport than suspended sand transport.

Influence of vegetation on the infilling of a macrotidal embayment: examples from salt marshes and shingle spit of the Baie de Somme (North France)

NASA Astrophysics Data System (ADS)

Le Bot, Sophie; Forey, Estelle; Lafite, Robert; Langlois, Estelle

2015-04-01

As many estuaries in the English Channel, the Baie de Somme is currently filling with a mean seabed elevation between 1.3 and 1.8 cm/yr. Embankments and polders, as well as sea level rise, increase this natural accretion process, which leads to important modifications of environment uses. Interactions between vegetation and sediment dynamics constitute a key-point to consider, in order to better understand the infilling processes in estuaries. To estimate the effect of vegetation on these processes, two particular environments have been studied in the bay: (i) the mid salt marsh covered with Halimione portulacoides, associated with a silty sedimentation, and (ii) the shingle spit, that closes the bay from the South, on which the sea kale (Crambe maritime), a protected pioneer species, develops. Salt marshes progress with a rate of 5-10 m/yr (mean value calculated on the 1947-2011 period). Sedimentological analysis have been conducted on 9 cores (50cm long) collected in three Halimione communities of the bay. They are associated with a silty-dominated (38-84 micrometer) sedimentation under the influence of decantation processes. Rhythmicity is observed in the sedimentation, due to the repetition of a two-layer pattern, that includes a dark layer composed of vegetal rests and that would represent annual sedimentation. Annual sedimentation rates (0.7 to 5.8 cm/yr) are consistent with mean values previously recorded. The shingle spit progresses to the North under the influence of the littoral drift at a rate of 7 m/yr (mean value calculated on the 1947-2011 period). Sea kales are observed on parts formed since several years, above the level of the highest astronomical tides. TLS surveys and sedimentation bars have allowed to measure erosion/sedimentation volumes at the scale of the spit and of sea kale individuals, during spring 2013. Individuals of this species facilitate the trapping of sand, transported by winds from the intertidal flats. Sea kale thus contributes to the maintenance of sand at the surface of the spit during spring (development period of sea kales) and, probably to the progressive silting up of the spit on a longer-term. Thus, sea kale indirectly favours the filling of the bay through the building up and consolidation of the spit that, in turn, enhances sheltered conditions increasing the part of decantation processes in the sedimentation in the bay. (financial support by Région Haute-Normandie and Réseau d'Observation du Littoral Normand et Picard, ROLNP)

The role of Callianassa subterranea (Montagu) (THALASSINIDEA) in sediment resuspension in the North Sea

NASA Astrophysics Data System (ADS)

Rowden, A. A.; Jones, M. B.; Morris, A. W.

1998-09-01

The mud shrimp Callianassa subterranea (Montagu) is a common member of the macrobenthic community at the site in the North Sea selected to study the dynamics of suspended sediment behaviour. The extensive burrowing habit of this deposit-feeding species makes it an important contributor to the degree of bioturbation experienced at the site. Individuals recovered from the site were returned to the laboratory to investigate the influence of body size and temperature upon the amount of sediment expelled. A clear relationship between these variables and the quantity of expelled sediment was identified, and a well-defined temporal pattern of expulsion activity and inactivity was demonstrated. These experimental data, together with field information on seawater temperatures and aspects of mud shrimp population dynamics, allow the construction of an estimated annual sediment turnover budget of 11 kg (dry weight) m -2 yr -1. Field observations at the North Sea site show that the sediment expelled by the mud shrimp forms unconsolidated volcano-like mounds, which significantly modify seabed surface topography. The dimensions of these surface features were measured from bottom photographs of the site and used to determine values of boundary roughness length ( Zo). In January Zo was 0.0007 cm, whilst in September Zo equaled 0.79 cm. Callianassa subterranea's maximum contribution to resuspension was assessed by calculating a derived lateral sediment transport rate of 7 kg m -1 month -1 (from values of near-bed current velocity, modified boundary roughness length and sediment turnover rate).

Calcium isotope evidence for suppression of carbonate dissolution in carbonate-bearing organic-rich sediments

NASA Astrophysics Data System (ADS)

Turchyn, Alexandra V.; DePaolo, Donald J.

2011-11-01

Pore fluid calcium isotope, calcium concentration and strontium concentration data are used to measure the rates of diagenetic dissolution and precipitation of calcite in deep-sea sediments containing abundant clay and organic material. This type of study of deep-sea sediment diagenesis provides unique information about the ultra-slow chemical reactions that occur in natural marine sediments that affect global geochemical cycles and the preservation of paleo-environmental information in carbonate fossils. For this study, calcium isotope ratios (δ 44/40Ca) of pore fluid calcium from Ocean Drilling Program (ODP) Sites 984 (North Atlantic) and 1082 (off the coast of West Africa) were measured to augment available pore fluid measurements of calcium and strontium concentration. Both study sites have high sedimentation rates and support quantitative sulfate reduction, methanogenesis and anaerobic methane oxidation. The pattern of change of δ 44/40Ca of pore fluid calcium versus depth at Sites 984 and 1082 differs markedly from that of previously studied deep-sea Sites like 590B and 807, which are composed of nearly pure carbonate sediment. In the 984 and 1082 pore fluids, δ 44/40Ca remains elevated near seawater values deep in the sediments, rather than shifting rapidly toward the δ 44/40Ca of carbonate solids. This observation indicates that the rate of calcite dissolution is far lower than at previously studied carbonate-rich sites. The data are fit using a numerical model, as well as more approximate analytical models, to estimate the rates of carbonate dissolution and precipitation and the relationship of these rates to the abundance of clay and organic material. Our models give mutually consistent results and indicate that calcite dissolution rates at Sites 984 and 1082 are roughly two orders of magnitude lower than at previously studied carbonate-rich sites, and the rate correlates with the abundance of clay. Our calculated rates are conservative for these sites (the actual rates could be significantly slower) because other processes that impact the calcium isotope composition of sedimentary pore fluid have not been included. The results provide direct geochemical evidence for the anecdotal observation that the best-preserved carbonate fossils are often found in clay or organic-rich sedimentary horizons. The results also suggest that the presence of clay minerals has a strong passivating effect on the surfaces of biogenic carbonate minerals, slowing dissolution dramatically even in relation to the already-slow rates typical of carbonate-rich sediments.

Erosion, storage, and transport of sediment in two subbasins of the Rio Puerco, New Mexico

USGS Publications Warehouse

Gellis, A.C.; Pavich, M.J.; Ellwein, A.L.; Aby, S.; Clark, I.; Wieczorek, M.E.; Viger, R.

2012-01-01

Arroyos in the American Southwest proceed through cut-and-fill cycles that operate at centennial to millennial time scales. The geomorphic community has put much effort into understanding the causes of arroyo cutting in the late Quaternary and in the modern record (late 1800s), while little effort has gone into understanding how arroyos fill and the sources of this fill. Here, we successfully develop a geographic information system (GIS)-modeled sediment budget that is based on detailed field measurements of hillslope and channel erosion and deposition. Field measurements were made in two arroyo basins draining different lithologies and undergoing different land disturbance (Volcano Hill Wash, 9.30 km2; Arroyo Chavez, 2.11 km2) over a 3 yr period. Both basins have incised channels that formed in response to the late nineteenth-century incision of the Rio Puerco. Large volumes of sediment were generated during arroyo incision, equal to more than 100 yr of the current annual total sediment load (bed load + suspended load) in each basin. Downstream reaches in both arroyos are presently aggrading, and the main source of the sediment is from channel erosion in upstream reaches and first- and second-order tributaries. The sediment budget shows that channel erosion is the largest source of sediment in the current stage of the arroyo cycle: 98% and 80% of the sediment exported out of Volcano Hill Wash and Arroyo Chavez, respectively. The geomorphic surface most affected by arroyo incision and one of the most important sediment sources is the valley alluvium, where channel erosion, gullying, soil piping, and grazing all occur. Erosion rates calculated for the entire Volcano Hill Wash (-0.26 mm/yr) and Arroyo Chavez (-0.53 mm/yr) basins are higher than the modeled upland erosion rates in each basin, reflecting the large contributions from channel erosion. Erosion rates in each basin are affected by a combination of land disturbance (grazing) and lithology--erodible sandstones and shales in Arroyo Chavez compared with basalt for Volcano Hill Wash. Despite these differences, hillslope sediment yields are similar to long-term denudation rates. As the arroyo fills over time from mouth to headwaters, hillslope sediment becomes a more significant sediment source.

Episodic fluid flow in the Nankai accretionary complex: Timescale, geochemistry, flow rates, and fluid budget

USGS Publications Warehouse

Saffer, D.M.; Bekins, B.A.

1998-01-01

Down-hole geochemical anomalies encountered in active accretionary systems can be used to constrain the timing, rates, and localization of fluid flow. Here we combine a coupled flow and solute transport model with a kinetic model for smectite dehydration to better understand and quantify fluid flow in the Nankai accretionary complex offshore of Japan. Compaction of sediments and clay dehydration provide fluid sources which drive the model flow system. We explicitly include the consolidation rate of underthrust sediments in our calculations to evaluate the impact that variations in this unknown quantity have on pressure and chloride distribution. Sensitivity analysis of steady state pressure solutions constrains bulk and flow conduit permeabilities. Steady state simulations with 30% smectite in the incoming sedimentary sequence result in minimum chloride concentrations at site 808 of 550 mM, but measured chlorinity is as low as 447 mM. We simulate the transient effects of hydrofracture or a strain event by assuming an instantaneous permeability increase of 3-4 orders of magnitude along a flow conduit (in this case the de??collement), using steady state results as initial conditions. Transient results with an increase in de??collement permeability from 10-16 m2 to 10-13 m2 and 20% smectite reproduce the observed chloride profile at site 808 after 80-160 kyr. Modeled chloride concentrations are highly sensitive to the consolidation rate of underthrust sediments, such that rapid compaction of underthrust material leads to increased freshening. Pressures within the de??collement during transient simulations rise rapidly to a significant fraction of lithostatic and remain high for at least 160 kyr, providing a mechanism for maintaining high permeability. Flow rates at the deformation front for transient simulations are in good agreement with direct measurements, but steady state flow rates are 2-3 orders of magnitude smaller than observed. Fluid budget calculations indicate that nearly 71% of the incoming water in the sediments leaves the accretionary wedge via diffuse flow out the seafloor, 0-5% escapes by focused flow along the de??collement, and roughly 1% is subducted. Copyright 1998 by the American Geophysical Union.

Modeling and sediment study in the watershed Medjerda, Tunisia

NASA Astrophysics Data System (ADS)

Kotti, Fatma; Mahé, Gil; Habaieb, Hamadi; Dieulin, Claudine; Hermassi, Taoufik

2015-04-01

Water projects have experienced a major expansion in the late 1980s, and we now have sufficient perspective to assess their actual performance and their socio-environmental impacts (Payan, 2007). This study focuses on the great watershed of Tunisia namely Medjerda which has an area of about 23,600 km2. In the main river of Medjerda some dams have been created for water retention: Sidi Salem Dam (the largest in the country), El Aroussia dam, and others on tributaries Mellegue Bouhertma, Siliana, Beni Mtir, Lakhemess and Kasseb. Since the construction of dams, essentially Sidi Salem and Siliana, the Medjerda river has undergone significant changes in morphology. The monitoring of the flow of the major hydrological stations in the pre-estuarine zone downstream from Sidi Salem dam is used to measure the impact of the constructions on hydrological regimes: reduction in average rates, reduction in volumes sold, altered seasonal pattern, and most of all reduction of the sediment transport, which the highest values are related to extreme events. In this context, the balance of sediment monitoring appears indispensable for the quantification of sediment transport at the outlet. Our approach is to calculate a specific flow rate relative to the area of the basin for every structure built in the Medjerda watershed, from the information available on transport and sedimentation rates known, combined with contours of each sub watershed. There are about ten dams spread throughout Medjerda watershed. The methodology is primarily developed for the Mellegue dam because we have at this station a long data set from 1955 until 2005. Other stations will be studied later on. The main objective of this study is to provide a series of annual variation of theoretical contributions. These calculated values will be compared with the actual measured sedimentary series. Two cores in the sediments of the pre-estuarine area are performed to determine past variability in sediment inputs over a time series than should be about one century. The cores' analysis results show a succession of sedimentary layers that likely correspond to different flood deposits that succeeded on this site, and especially the datation of the cores shows that the selected area is a very important deposition area. This sedimentary study will help estimate the sediment dynamics to major estuaries, which is poorly known for most of the rivers of Maghreb. The reduction of the sediment supply to the sea is tipped as a major factor to be taken into account for a better understanding of the dynamics of coastal areas in the context of global climate change and sea level rise. Keywords: sediment core, Medjerda watershed, dam, hydrology, modeling, Tunisia

Fluvial sediment transport in a glacier-fed high-mountain river (Riffler Bach, Austrian Alps)

NASA Astrophysics Data System (ADS)

Morche, David; Weber, Martin; Faust, Matthias; Schuchardt, Anne; Baewert, Henning

2017-04-01

High-alpine environments are strongly affected by glacier retreat since the Little Ice Age (LIA). Due to ongoing climate change the hydrology of proglacial rivers is also influenced. It is expected that the growing proportions of snow melt and rainfall events will change runoff characteristics of proglacial rivers. Additionally, the importance of paraglacial sediment sources in recently deglaciating glacier forefields is increasing, while the role of glacial erosion is declining. Thus complex environmental conditions leading to a complex pattern of fluvial sediment transport in partly glaciated catchments of the European Alps. Under the umbrella of the joint PROSA-project the fluvial sediment transport of the river Riffler Bach (Kaunertal, Tyrol, Austria) was studied in 3 consecutive ablation seasons in order to quantify sediment yields. In June 2012 a probe for water level and an automatic water sampler (AWS) were installed at the outlet of the catchment (20km2). In order to calculate annual stage-discharge-relations by the rating-curve approach, discharge (Q) was repeatedly measured with current meters and by salt dilution. Concurrent to the discharge measurements bed load was collected using a portable Helley-Smith sampler. Bed load samples were weighted and sieved in the laboratory to gain annual bed load rating curves and grain size distributions. In total 564 (2012: 154, 2013: 209, 2014: 201) water samples were collected and subsequently filtered to quantify suspended sediment concentrations (SSC). Q-SSC-relations were calculated for single flood events due to the high variability of suspended sediment transport. The results show a high inter- and intra-annual variability of solid fluvial sediment transport, which can be explained by the characteristics of suspended sediment transport. Only 13 of 22 event-based Q-SSC-relations show causal dependency. In 2012, during a period with multiple pluvial-induced peak discharges most sediment was transported. On the contrary the importance of snow melt for sediment transport was indicated during the ablation season 2013. In total 3582 t of sediment were exported out of the Riffler Bach catchment in 2012, which is almost twice the solid sediment load of the ablation season 2013 (1953 t). Total solid load of the Riffler Bach River was 3511 t in 2014 Suspended sediment load was dominant in all ablation seasons. The result of additional DEM analysis reveals that 37 % of the catchment do not contribute or only contribute to a lesser amount to the fluvial sediment export out of the catchment. The findings of the grain size analysis imply glacigenic origin of the transported particles. Thus, the results indicate that solid sediment transport is not only a function of discharge. Also availability of sediment and the systems state of (dis-)connectivity, e.g. coupling of sediment sources to the river, need to be considered.

Seasonal-Scale Sedimentology and Restoration Potential in a Diversion-Fed Coastal Louisiana Wetland

NASA Astrophysics Data System (ADS)

Keogh, M.; Kolker, A.

2016-02-01

Coastal Louisiana is threatened by high rates of subsidence and rapid land loss. One promising method to mitigate this land loss is to divert Mississippi River water into surrounding wetlands. This study examines the impacts of one such diversion. Completed in 2002, Davis Pond Freshwater Diversion is located approximately 35 river km upstream of New Orleans. Although initially designed and operated to reduce salinity levels in the interior marsh, the diversion also delivers sediment and nutrients to the subsiding wetland. As a result, new land has emerged adjacent to the Davis Pond outfall channel in recent years. Here we examine patterns of seasonal-scale sediment accumulation and retention in the marsh surrounding Davis Pond diversion. Twenty-two short (5-cm) sediment cores were collected in spring 2015 immediately following a 13-day experimental release of Mississippi River water through the diversion. During this time, discharge increased from a base flow of approximately 28 m3s-1 (1,000 ft3s-1) to an elevated flow of between 142 and 283 m3s-1 (5,000 and 10,000 ft3s-1), before returning to base flow. A second set of cores were collected in fall 2015 after a 6-month period of base flow. Sediment cores were analyzed for organic content, bulk density, and grain size. In addition, inventories of beryllium-7 were used to calculate seasonal-scale sediment accumulation and retention rates. This work leads to the development of a sediment budget for the Davis Pond area and determination of long-term sediment trapping rates. Davis Pond Freshwater Diversion is an understudied system that can provide a scalable model for coast-wide restoration projects critical to the protection of Gulf Coast communities.

Transport of chromium and selenium in the suboxic zone of a shallow aquifer: Influence of redox and adsorption reactions

USGS Publications Warehouse

Kent, D.B.; Davis, J.A.; Anderson, L.C.D.; Rea, B.A.; Waite, T.D.

1994-01-01

Breakthrough of Cr(VI) (chromate), Se(VI) (selenate), and O2 (dissolved oxygen) was observed in tracer tests conducted in a shallow, sand and gravel aquifer with mildly reducing conditions. Loss of Cr, probably due to reduction of Cr(VI) to Cr(III) and irreversible sorption of Cr(III), occurred along with slight retardation of Cr(VI), owing to reversible sorption. Reduction of Se(VI) and O2 was thermodynamically feasible but did not occur, indicating conditions, were unfavorable to microbial reduction. Cr(VI) reduction by constituents of aquifer sediments did not achieve local equilibrium during transport. The reduction rate was probably limited by incomplete contact between Cr(VI) transported along predominant flow paths and reductants located in regions within aquifer sediments of comparatively low permeability. Scatter in the amount of Cr reduction calculated from individual breakthrough curves at identical distances downgradient probably resulted from heterogeneities in the distribution of reductants in the sediments. Predictive modeling of the transport and fate of redox-sensitive solutes cannot be based strictly on thermodynamic considerations; knowledge of reaction rates is critical. Potentially important mass transfer rate limitations between solutes and reactants in sediments as well as heterogeneities in the distribution of redox properties in aquifers complicate determination of limiting rates for use in predictive simulations of the transport of redox-sensitive contaminants in groundwater.

Relationships between thermal maturity indices calculated using Arrhenius equation and Lopatin method: implications for petroleum exploration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, D.A.

1988-02-01

Thermal maturity can be calculated with time-temperature indices (TTI) based on the Arrhenius equation using kinetics applicable to a range of Types II and III kerogens. These TTIs are compared with TTI calculations based on the Lopatin method and are related theoretically (and empirically via vitrinite reflectance) to the petroleum-generation window. The TTIs for both methods are expressed mathematically as integrals of temperature combined with variable linear heating rates for selected temperature intervals. Heating rates control the thermal-maturation trends of buried sediments. Relative to Arrhenius TTIs, Lopatin TTIs tend to underestimate thermal maturity at high heating rates and overestimate itmore » as low heating rates. Complex burial histories applicable to a range of tectonic environments illustrate the different exploration decisions that might be made on the basis of independent results of these two thermal-maturation models. 15 figures, 8 tables.« less

A Sensitivity Analysis of Triggers and Mechanisms of Mass Movements in Fjords

NASA Astrophysics Data System (ADS)

Overeem, I.; Lintern, G.; Hill, P.

2016-12-01

Fjords are characterized by rapid sedimentation as they typically drain glaciated river catchments with high seasonal discharges and large sediment evacuation rates. For this reason, fjords commonly experience submarine mass movements; failures of the steep delta front that trigger tsunamis, and turbidity currents or debris flows. Repeat high-resolution bathymetric surveys, and in-situ process measurements collected in fjords in British Columbia, Canada, indicate that mass movements occur many times per year in some fjords and are more rare and of larger magnitude in other fjords. We ask whether these differences can be attributed to river discharge characteristics or to grainsize characteristics of the delivered sediment. To test our ideas, we couple a climate-driven river sediment transport model, HydroTrend, and a marine sedimentation model, Sedflux2D, to explore the triggers of submarine failures and mechanisms of subsequent turbidity and debris flows. HydroTrend calculates water and suspended sediment transport on a daily basis based on catchment characteristics, glaciated area, lakes and temperature and precipitation regime. Sedflux uses the generated river time-series to simulate delta plumes, failures and mass movements with separate process models. Model uncertainty and parameter sensitivity are assessed using Dakota Tools, which allows for a systematic exploration of the effects of river basin characteristics and climate scenarios on occurrence of hyperpycnal events, delta front sedimentation rate, submarine pore pressure, failure frequency and size, and run-out distances. Preliminary simulation results point to the importance of proglacial lakes and lakes abundance in the river basin, which has profound implications for event-based sediment delivery to the delta apex. Discharge-sediment rating curves can be highly variable based on these parameters. Distinction of turbidity currents and debris flows was found to be most sensitive to both earthquake frequency and delta front grainsize. As a first step we compare these model experiments against field data from the Squamish River and Delta in Howe Sound, BC.

Evaluating the competing effects of lithology and sediment supply on the erosional dynamics of rivers crossing active faults.

NASA Astrophysics Data System (ADS)

Whittaker, Alex; Boulton, Sarah; Kent, Emiko; Zondervan, Jesse; Hann, Madeleine; Watkins, Stephen; Bell, Rebecca; Brooke, Sam

2017-04-01

Lithology and sediment supply influence the erosional dynamics of rivers crossing active faults and together these effects govern the style, timescale and means by which landscapes respond to their tectono-climatic boundary conditions. Here, for transient bedrock catchments in the Gediz Graben, Turkey, and the Gulf of Corinth, Greece, for which the timing and rate of active faulting is known, we quantify the relative importance of rock strength and sediment supply on models of fluvial incision. We determine rock type, strength and erodibility using a Schmidt hammer and structural measurements of joint density and size. We evaluate the downstream distribution of channel width and stream power and calculate the extent to which the latter scales with tectonic rates and rock strength. Sediment supply is constrained using estimates of bedrock exposure, transport capacities and erosional fluxes. For the Turkish examples, stream powers in the metamorphic rocks are four times greater than in the Neogene sediment units, indicating a four-fold difference in bedrock erodibility, K, for a two-fold variation in in Schmidt hammer hardness. In the Gulf of Corinth examples, we interpret differences in stream powers near the active faults to represent order of magnitude differences in bedrock erodibility between carbonate and sandstone/conglomerate units. We also observe that in both cases, significant along-strike variation in fault slip rate is not associated with an increase in stream power for the sedimentary rocks and we assess the extent to which this stream power deficit may also represent the effects of sediment-flux-dependent incision.

Organic carbon burial in a mangrove forest, margin and intertidal mud flat

NASA Astrophysics Data System (ADS)

Sanders, Christian J.; Smoak, Joseph M.; Naidu, A. Sathy; Sanders, Luciana M.; Patchineelam, Sambasiva R.

2010-12-01

The flux of total organic carbon (TOC) to depositional facies (intertidal mud flat, margin and forest) was quantified for a tropical mangrove forest in Brazil. Results indicate that these mangrove margins and intertidal mudflats are sites of large TOC accumulation, almost four times greater than the global averages for mangrove forests. The TOC burial rates were determined from organic carbon content in sediment cores which were dated using 210Pb. Burial rates were calculated to be 1129, 949, and 353 (g m -2 yr -1), for the mud flat, margin and forest, respectively. Sediment accumulation rates (SAR) were estimated to be 7.3, 5.0 and 2.8 mm yr -1. Sediment characterization (δ 13C, δ 15N, TOC/TN and mud fraction) indicated a representative mangrove system with a record of consistent organic matter flux of up to 100 years. Because of substantial burial of organic carbon in mangrove ecosystems, their role in the global carbon budget must be considered. More importantly, as climate change influences temperature and sea level, mangrove ecosystems will respond to specific climatic conditions.

Suspended sediment load below open-cast mines for ungauged river basin

NASA Astrophysics Data System (ADS)

Kuksina, L.

2011-12-01

Placer mines are located in river valleys along river benches or river ancient channels. Frequently the existing mining sites are characterized by low contribution of the environmental technologies. Therefore open-pit mining alters stream hydrology and sediment processes and enhances sediment transport. The most serious environmental consequences of the sediment yield increase occur in the rivers populated by salmon fish community because salmon species prefer clean water with low turbidity. For instance, placer mining located in Kamchatka peninsula (Far East of Russia) which is regarded to be the last global gene pool of wild salmon Oncorhynchus threatens rivers ecosystems significantly. Impact assessment is limited by the hydrological observations scarcity. Gauging network is rare and in many cases whole basins up to 200 km length miss any hydrological data. The main purpose of the work is elaboration of methods for sediment yield estimation in rivers under mining impact and implementation of corresponding calculations. Subjects of the study are rivers of the Vivenka river basin where open-cast platinum mine is situated. It's one of the largest platinum mines in Russian Federation and in the world. This mine is the most well-studied in Kamchatka (research covers a period from 2003 to 2011). Empirical - analytical model of suspended sediment yield estimation was elaborated for rivers draining mine's territories. Sediment delivery at the open-cast mine happens due to the following sediment processes: - erosion in the channel diversions; - soil erosion on the exposed hillsides; - effluent from settling ponds; - mine waste water inflow; - accident mine waste water escape into rivers. Sediment washout caused by erosion was estimated by repeated measurements of the channel profiles in 2003, 2006 and 2008. Estimation of horizontal deformation rates was carried out on the basis of erosion dependence on water discharge rates, slopes and composition of sediments. Soil erosion on the exposed hillsides was estimated taking into account precipitation of various intensity and solid material washout during this period. Effluent from settling ponds was calculated on the basis of minimum anthropogenic turbidity. Its value is difference in background turbidity and minimal turbidity caused by effluent and waste water overflow. Mine waste water inflow was estimated due to actual data on water balance of purification system. Accident mine waste water escape into rivers was estimated by duration and material washout during accidents data measured during observation period. Total suspended sediment yield of rivers draining mine's territory is the sum of its components. Total sediment supply from mining site is 24.7 % from the Vivenka sediment yield. Polluted placer-mined rivers contribute about 35.4 % of the whole sediment yield of the Vivenka river. At the same time the catchment area of these rivers is less than 0.2 % from the whole Vivenka catchment area.

Anthropic influences on the sedimentation rates of lakes situated in different geographic areas.

PubMed

Simon, Hedvig; Kelemen, Szabolcs; Begy, Róbert-Csaba

2017-07-01

The aim of this study is to determine the effects of natural and anthropic events occurring in the last 30 years in the catchment areas of four Romanian lakes (St. Anna Lake, Red Lake, Vârşolţ Lake and Matiţa Lake) originating from four different geomorphologic areas. A total of eleven sediment cores have been processed for age and sedimentation rate determination using the 210 Pb dating method. Total 210 Pb was measured via alpha spectrometry by 210 Po using PIPS detectors, while supported 210 Pb was measured by 226 Ra using HPGe detectors. Ages and sedimentation rates were calculated using the CRS model. The values of the sedimentation rates have grown multiply in the last three decades: 2.66 times in case of the St. Anna Lake (from 0.06 ± 0.01 g/cm 2 y to 0.16 ± 0.02 g/cm 2 y), up to 6.72 times in case of Red Lake (0.36 ± 0.04 g/cm 2 y to 2.42 ± 0.36 g/cm 2 y), 4.02 times in case of Vârşolţ Lake (04 g/cm 2 y to 1.53 ± 0.18 g/cm 2 y) and up to 16.18 times in case of Matiţa Lake (0.27 ± 0.03 g/cm 2 y to 4.37 ± 0.32). Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing the Importance of Cross-Stream Transport in Bedload Flux Estimates from Migrating Dunes: Colorado River, Grand Canyon National Park

NASA Astrophysics Data System (ADS)

Leary, K. P.; Buscombe, D.; Schmeeckle, M.; Kaplinski, M. A.

2017-12-01

Bedforms are ubiquitous in sand-bedded rivers, and understanding their morphodynamics is key to quantifying bedload transport. As such, mechanistic understanding of the spatiotemporal details of sand transport through and over bedforms is paramount to quantifying total sediment flux in sand-bedded river systems. However, due to the complexity of bedform field geometries and migration in natural settings, our ability to relate migration to bedload flux, and to quantify the relative role of tractive and suspended processes in their dynamics, is incomplete. Recent flume and numerical investigations indicate the potential importance of cross-stream transport, a process previously regarded as secondary and diffusive, to the three-dimensionality of bedforms and spatially variable translation and deformation rates. This research seeks to understand and quantify the importance of cross-stream transport in bedform three-dimensionality in a field setting. This work utilizes a high-resolution (0.25 m grid) data set of bedforms migrating in the channel of the Colorado River in Grand Canyon National Park. This data set comprises multi-beam sonar surveys collected at 3 different flow discharges ( 283, 566, and 1076 m3/s) along a reach of the Colorado River just upstream of the Diamond Creek USGS gage. Data were collected every 6 minutes almost continuously for 12 hours. Using bed elevation profiles (BEPs), we extract detailed bedform geometrical data (i.e. bedform height, wavelength) and spatial sediment flux data over a suite of bedforms at each flow. Coupling this spatially extensive data with a generalized Exner equation, we conduct mass balance calculations that evaluate the possibility, and potential importance, of cross-stream transport in the spatial variability of translation and deformation rates. Preliminary results suggest that intra-dune cross-stream transport can partially account for changes in the planform shape of dunes and may play an important role in spatially variable translation and deformation rates. Parameterization of cross-stream sediment transport could lead to accounting for ambiguities in bedload flux calculations caused by dune deformation, which in turn could significantly improve overall calculation of bedload and total load sediment transport in sand bedded rivers.

Facing the scaling problem: A multi-methodical approach to simulate soil erosion at hillslope and catchment scale

NASA Astrophysics Data System (ADS)

Schmengler, A. C.; Vlek, P. L. G.

2012-04-01

Modelling soil erosion requires a holistic understanding of the sediment dynamics in a complex environment. As most erosion models are scale-dependent and their parameterization is spatially limited, their application often requires special care, particularly in data-scarce environments. This study presents a hierarchical approach to overcome the limitations of a single model by using various quantitative methods and soil erosion models to cope with the issues of scale. At hillslope scale, the physically-based Water Erosion Prediction Project (WEPP)-model is used to simulate soil loss and deposition processes. Model simulations of soil loss vary between 5 to 50 t ha-1 yr-1 dependent on the spatial location on the hillslope and have only limited correspondence with the results of the 137Cs technique. These differences in absolute soil loss values could be either due to internal shortcomings of each approach or to external scale-related uncertainties. Pedo-geomorphological soil investigations along a catena confirm that estimations by the 137Cs technique are more appropriate in reflecting both the spatial extent and magnitude of soil erosion at hillslope scale. In order to account for sediment dynamics at a larger scale, the spatially-distributed WaTEM/SEDEM model is used to simulate soil erosion at catchment scale and to predict sediment delivery rates into a small water reservoir. Predicted sediment yield rates are compared with results gained from a bathymetric survey and sediment core analysis. Results show that specific sediment rates of 0.6 t ha-1 yr-1 by the model are in close agreement with observed sediment yield calculated from stratigraphical changes and downcore variations in 137Cs concentrations. Sediment erosion rates averaged over the entire catchment of 1 to 2 t ha-1 yr-1 are significantly lower than results obtained at hillslope scale confirming an inverse correlation between the magnitude of erosion rates and the spatial scale of the model. The study has shown that the use of multiple methods facilitates the calibration and validation of models and might provide a more accurate measure for soil erosion rates in ungauged catchments. Moreover, the approach could be used to identify the most appropriate working and operational scales for soil erosion modelling.

Deep-sea spherules from Pacific clay - Mass distribution and influx rate. [extraterrestrial origins from optical and electron microscopy

NASA Technical Reports Server (NTRS)

Murrell, M. T.; Davis, P. A., Jr.; Nishiizumi, K.; Millard, H. T., Jr.

1980-01-01

From 411 kg of Pacific clay, 22 mg of stony spherules and 50 mg of iron spherules larger than 150 microns were concentrated. The extraterrestrial origin of these particles was evaluated with the aid of optical and electron microscopy and atomic absorption elemental analysis. An expression for the integral number of stony particles from this sediment in the mass range 20-300 micrograms was derived. The world-wide influx rate of stony particles in the mass range which survive atmospheric heating and ocean sediment storage is calculated to be 90 tons/yr. The relative contributions of ablation debris vs fused interplanetary dust to the influx of stony spherules is discussed, but no conclusions could be made.

Wetland management reduces sediment and nutrient loading to the upper Mississippi River

USGS Publications Warehouse

Kreiling, Rebecca M.; Schubauer-Berigan, Joseph P.; Richardson, William B.; Bartsch, Lynn; Hughes, Peter E.; Strauss, Eric A.

2013-01-01

Restored riparian wetlands in the Upper Mississippi River basin have potential to remove sediment and nutrients from tributaries before they flow into the Mississippi River. For 3 yr we calculated retention efficiencies of a marsh complex, which consisted of a restored marsh and an adjacent natural marsh that were connected to Halfway Creek, a small tributary of the Mississippi. We measured sediment, N, and P removal through a mass balance budget approach, N removal through denitrification, and N and P removal through mechanical soil excavation. The marsh complex had average retention rates of approximately 30 Mg sediment ha−1 yr−1, 26 kg total N ha−1 yr−1, and 20 kg total P ha−1 yr−1. Water flowed into the restored marsh only during high-discharge events. Although the majority of retention occurred in the natural marsh, portions of the natural marsh were hydrologically disconnected at low discharge due to historical over-bank sedimentation. The natural marsh removed >60% of sediment, >10% of P, and >5% of N loads (except the first year, when it was a N source). The marsh complex was a source of NH4+ and soluble reactive P. The average denitrification rate for the marsh complex was 2.88 mg N m−2 h−1. Soil excavation removed 3600 Mg of sediment, 5.6 Mg of N, and 2.7 Mg of P from the restored marsh. The marsh complex was effective in removing sediment and nutrients from storm flows; however, retention could be increased if more water was diverted into both restored and natural marshes before entering the river.

Natural radioactivity of riverbank sediments of the Maritza and Tundja Rivers in Turkey.

PubMed

Aytas, Sule; Yusan, Sabriye; Aslani, Mahmoud A A; Karali, Turgay; Turkozu, D Alkim; Gok, Cem; Erenturk, Sema; Gokce, Melis; Oguz, K Firat

2012-01-01

This article represents the first results of the natural radionuclides in the Maritza and Tundja river sediments, in the vicinity of Edirne city, Turkey. The aim of the article is to describe the natural radioactivity concentrations as a baseline for further studies and to obtain the distribution patterns of radioactivity in trans-boundary river sediments of the Maritza and Tundja, which are shared by Turkey, Bulgaria and Greece. Sediment samples were collected during the period of August 2007-April 2010. The riverbank sediment samples were analyzed firstly for their pH, organic matter content and soil texture. The gross alpha/beta and (238)U, (232)Th and (40)K activity concentrations were then investigated in the collected sediment samples. The mean and standard error of mean values of gross alpha and gross beta activity concentrations were found as 91 ± 11, 410 ± 69 Bq/kg and 86 ± 11, 583 ± 109 Bq/kg for the Maritza and Tundja river sediments, respectively. Moreover, the mean and standard error of mean values of (238)U, (232)Th and (40)K activity concentrations were determined as 219 ± 68, 128 ± 55, 298 ± 13 and as 186 ± 98, 121 ± 68, 222 ± 30 Bq/kg for the Maritza and Tundja River, respectively. Absorbed dose rates (D) and annual effective dose equivalent s have been calculated for each sampling point. The average value of adsorbed dose rate and effective dose equivalent were found as 191 and 169 nGy/h; 2 and 2 mSv/y for the Maritza and the Tundja river sediments, respectively.

Infiltration and quality of water for two arroyo channels, Albuquerque, New Mexico, 1988-92

USGS Publications Warehouse

Thomas, Carole L.

1995-01-01

Selected reaches of Grant Line Arroyo and Tijeras Arroyo in Albuquerque, New Mexico, were studied to collect information about the amount and quality of infiltration through arroyo channels. Infiltration rate was calculated for selected reaches of Grant Line Arroyo and Tijeras Arroyo based on instantaneous streamflow-loss volumes, wetted channel area, and instantaneous evaporation rates measured during 1988-92. Infiltration rates at Grant Line Arroyo ranged from 0.0 to 0.6 foot per day, and at Tijeras Arroyo from 2.28 to 30 feet per day. The evaporation rate ranged from one-tenth of 1 percent to 2 percent of the infiltration rate. Infiltration rates differed with the location of the reach isolated for measurement and with the time of day of the infiltration-rate measurement. Differences in intrinsic permeability of the sediments may be the most important factor affecting spatial variations in infiltration. The most important factor affecting temporal variations in infiltration may be the temperature of the water and sediment where infiltration occurs. Annual evaporation rates were greatest over saturated stream sediments and ranged from 802 to 1,025 millimeters per year or from 31.57 to 40.35 inches per year. Annual evaporation rates were least over unsaturated, unvegetated soil and ranged from 174 to 291 millimeters per year or from 6.85 to 11.46 inches per year. Annual evapotranspiration rates over grasses or shrubs or both were about one-half the rates over saturated stream sediments. Rates were similar for Grant Line and Tijeras Arroyos. The land- surface vegetation, availability of water at the land surface, availability of energy to enable a change of state from water to vapor, existence of a vapor concentration gradient, and a turbulent atmosphere to carry the vapor away may be the factors that determine the amount of evaporation and evapotranspiration. Water in Grant Line Arroyo and Tijeras Arroyo met U. S. Environmental Protection Agency drinking-water regulations for nitrate, volatile organic compounds, dissolved lead, and dissolved and total arsenic, barium, cadmium, chromium, copper, iron, silver, zinc, selenium, chloride, and sulfate concentrations. Total lead concentration in one sample from Tramway Floodway Channel, a tributary to Tijeras Arroyo, was 55 micrograms per liter, exceeding the Environmental Protection Agency drinking-water regulation of 50 micrograms per liter. Dissolved-solids concentrations calculated from the sum of cations and anions usually exceeded the Environmental Protection Agency drinking-water dissolved-solids regulation of 500 milligrams per liter at Tijeras Arroyo above Four Hills Bridge.

Estimating accumulation rates and physical properties of sediment behind a dam: Englebright Lake, Yuba River, northern California

USGS Publications Warehouse

Snyder, Noah P.; Rubin, David M.; Alpers, Charles N.; Childs, Jonathan R.; Curtis, Jennifer A.; Flint, Lorraine E.; Wright, Scott A.

2004-01-01

Studies of reservoir sedimentation are vital to understanding scientific and management issues related to watershed sediment budgets, depositional processes, reservoir operations, and dam decommissioning. Here we quantify the mass, organic content, and grain-size distribution of a reservoir deposit in northern California by two methods of extrapolating measurements of sediment physical properties from cores to the entire volume of impounded material. Englebright Dam, completed in 1940, is located on the Yuba River in the Sierra Nevada foothills. A research program is underway to assess the feasibility of introducing wild anadromous fish species to the river upstream of the dam. Possible management scenarios include removing or lowering the dam, which could cause downstream transport of stored sediment. In 2001 the volume of sediments deposited behind Englebright Dam occupied 25.5% of the original reservoir capacity. The physical properties of this deposit were calculated using data from a coring campaign that sampled the entire reservoir sediment thickness (6–32 m) at six locations in the downstream ∼3/4 of the reservoir. As a result, the sediment in the downstream part of the reservoir is well characterized, but in the coarse, upstream part of the reservoir, only surficial sediments were sampled, so calculations there are more uncertain. Extrapolation from one-dimensional vertical sections of sediment sampled in cores to entire three-dimensional volumes of the reservoir deposit is accomplished via two methods, using assumptions of variable and constant layer thickness. Overall, the two extrapolation methods yield nearly identical estimates of the mass of the reservoir deposit of ∼26 × 106 metric tons (t) of material, of which 64.7–68.5% is sand and gravel. Over the 61 year reservoir history this corresponds to a maximum basin-wide sediment yield of ∼340 t/km2/yr, assuming no contribution from upstream parts of the watershed impounded by other dams. The uncertainties and limitations of the estimates of overall sediment quantities are discussed. Implications for watershed management and future reservoir sedimentation studies are also presented.

Variations in grain-scale sediment structure and entrainment force in a gravel-bed channel as a function of fine sediment content and morphological location

NASA Astrophysics Data System (ADS)

Voepel, Hal; Ahmed, Sharif; Hodge, Rebecca; Leyland, Julian; Sear, David

2017-04-01

One of the major causes of uncertainty in estimates of bedload transport rates in gravel-bed rivers is a lack of understanding of grain-scale sediment structure, and the impact that this structure has on the force required to entrain sediment. There are at least two factors that standard entrainment models do not consider. The first is the way in which the spatial arrangement and orientation of grains and the resultant forces varies throughout a channel and over time, ways that have yet to be fully quantified. The second is that sediment entrainment is a 3D process, yet calculations of entrainment thresholds for sediment grains are typically based on 2D diagrams where we calculate static moments of force vectors about a pivot angle, represented as a single point rather than as a more realistic axis of rotation. Our research addresses these limitations by quantifying variations in 3D sediment structure and entrainment force requirements across two key parameters: morphological location within a riffle-pool sequence (reflecting variation in hydraulic conditions), and the fine sediment content of the gravel-bed (sand and clay). We report results from a series of flume experiments in which we water-worked a gravel-bed with a riffle-pool morphology containing varying amounts of fine sediment. After each experimental run intact samples of the bed at different locations were extracted and the internal structure of the bed was measured using non-destructive, micro-focus X-ray computed tomography (CT) imaging. The CT images were processed to measure the properties of individual grains, including volume, center of mass, dimension, and contact points. From these data we were able to quantify the sediment structure and entrainment force requirements through measurement of 3D metrics including grain pivot angles, grain exposure and protrusion. Comparison of the metrics across different morphological locations and fine sediment content demonstrates how these factors affect the bed structure and entrainment force requirement. These results have implications for the development of sediment entrainment models for gravel-bed rivers. Keywords: fluvial sediment, geomorphology, entrainment models, X-ray computed tomography, 3D imaging, vector mechanics

Modeling of microalgal shear-induced flocculation and sedimentation using a coupled CFD-population balance approach.

PubMed

Golzarijalal, Mohammad; Zokaee Ashtiani, Farzin; Dabir, Bahram

2018-01-01

In this study, shear-induced flocculation modeling of Chlorella sp. microalgae was conducted by combination of population balance modeling and CFD. The inhomogeneous Multiple Size Group (MUSIG) and the Euler-Euler two fluid models were coupled via Ansys-CFX-15 software package to achieve both fluid and particle dynamics during the flocculation. For the first time, a detailed model was proposed to calculate the collision frequency and breakage rate during the microalgae flocculation by means of the response surface methodology as a tool for optimization. The particle size distribution resulted from the model was in good agreement with that of the jar test experiment. Furthermore, the subsequent sedimentation step was also examined by removing the shear rate in both simulations and experiments. Consequently, variation in the shear rate and its effects on the flocculation behavior, sedimentation rate and recovery efficiency were evaluated. Results indicate that flocculation of Chlorella sp. microalgae under shear rates of 37, 182, and 387 s -1 is a promising method of pre-concentration which guarantees the cost efficiency of the subsequent harvesting process by recovering more than 90% of the biomass. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 34:160-174, 2018. © 2017 American Institute of Chemical Engineers.

Calculating mercury loading to the tidal Hudson River, New York, using rating curve and surrogate methodologies

USGS Publications Warehouse

Wall, G.R.; Ingleston, H.H.; Litten, S.

2005-01-01

Total mercury (THg) load in rivers is often calculated from a site-specific "rating-curve" based on the relation between THg concentration and river discharge along with a continuous record of river discharge. However, there is no physical explanation as to why river discharge should consistently predict THg or any other suspended analyte. THg loads calculated by the rating-curve method were compared with those calculated by a "continuous surrogate concentration" (CSC) method in which a relation between THg concentration and suspended-sediment concentration (SSC) is constructed; THg loads then can be calculated from the continuous record of SSC and river discharge. The rating-curve and CSC methods, respectively, indicated annual THg loads of 46.4 and 75.1 kg for the Mohawk River, and 52.9 and 33.1 kg for the upper Hudson River. Differences between the results of the two methods are attributed to the inability of the rating-curve method to adequately characterize atypical high flows such as an ice-dam release, or to account for hysteresis, which typically degrades the strength of the relation between stream discharge and concentration of material in suspension. ?? Springer 2005.

Application of RAD-BCG calculator to Hanford's 300 area shoreline characterization dataset

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antonio, Ernest J.; Poston, Ted M.; Tiller, Brett L.

2003-07-01

Abstract. In 2001, a multi-agency study was conducted to characterize potential environmental effects from radiological and chemical contaminants on the near-shore environment of the Columbia River at the 300 Area of the U.S. Department of Energy’s Hanford Site. Historically, the 300 Area was the location of nuclear fuel fabrication and was the main location for research and development activities from the 1940s until the late 1980s. During past waste handling practices uranium, copper, and other heavy metals were routed to liquid waste streams and ponds near the Columbia River shoreline. The Washington State Department of Health and the Pacific Northwestmore » National Laboratory’s Surface Environmental Surveillance Project sampled various environmental components including river water, riverbank spring water, sediment, fishes, crustaceans, bivalve mollusks, aquatic insects, riparian vegetation, small mammals, and terrestrial invertebrates for analyses of radiological and chemical constituents. The radiological analysis results for water and sediment were used as initial input into the RAD-BCG Calculator. The RAD-BCG Calculator, a computer program that uses an Excel® spreadsheet and Visual Basic® software, showed that maximum radionuclide concentrations measured in water and sediment were lower than the initial screening criteria for concentrations to produce dose rates at existing or proposed limits. Radionuclide concentrations measured in biota samples were used to calculate site-specific bioaccumulation coefficients (Biv) to test the utility of the RAD-BCG-Calculator’s site-specific screening phase. To further evaluate site-specific effects, the default Relative Biological Effect (RBE) for internal alpha particle emissions was reduced by half and the program’s kinetic/allometric calculation approach was initiated. The subsequent calculations showed the initial RAD-BCG Calculator results to be conservative, which is appropriate for screening purposes.« less

Assessment of total bed material equations on selected Malaysia rivers

NASA Astrophysics Data System (ADS)

Saleh, A.; Abustan, I.; Mohd Remy Rozainy, M. A. Z.; Sabtu, N.

2017-10-01

Assessment of total sediment load equations on selected Malaysia rivers was done based on 35 sediment loads and hydraulic data. Four rivers were selected to make this assessment which are Sungai Perak, Sungai Kemaman, Sungai Pergau and Sungai Kurau. These rivers can be divided into three categories based on the river width, with Sungai Perak (300-350m) and Sungai Kemaman (150-200m) can categorised as big rivers, meanwhile, Sungai Pergau (30-45m) and Sungai Kurau (10-11m) can categorised as medium and small river respectively. The total sediment load equations used in this assessment are Ackers-White, Brownlie, Engelund-Hansen, Graf, Molinas-Wu, Karim-Kennedy and Yang. This paper also tested the local total sediment load equations by Ariffin and Sinnakaudan et al. to evaluate capabilities of the equations on different rivers in Malaysia. The graphs of the calculated equations versus measured sediment transport rates were plotted to shows the accuracy of the tested equations.

Sediment residence times constrained by uranium-series isotopes: A critical appraisal of the comminution approach

NASA Astrophysics Data System (ADS)

Handley, Heather K.; Turner, Simon; Afonso, Juan C.; Dosseto, Anthony; Cohen, Tim

2013-02-01

Quantifying the rates of landscape evolution in response to climate change is inhibited by the difficulty of dating the formation of continental detrital sediments. We present uranium isotope data for Cooper Creek palaeochannel sediments from the Lake Eyre Basin in semi-arid South Australia in order to attempt to determine the formation ages and hence residence times of the sediments. To calculate the amount of recoil loss of 234U, a key input parameter used in the comminution approach, we use two suggested methods (weighted geometric and surface area measurement with an incorporated fractal correction) and typical assumed input parameter values found in the literature. The calculated recoil loss factors and comminution ages are highly dependent on the method of recoil loss factor determination used and the chosen assumptions. To appraise the ramifications of the assumptions inherent in the comminution age approach and determine individual and combined comminution age uncertainties associated to each variable, Monte Carlo simulations were conducted for a synthetic sediment sample. Using a reasonable associated uncertainty for each input factor and including variations in the source rock and measured (234U/238U) ratios, the total combined uncertainty on comminution age in our simulation (for both methods of recoil loss factor estimation) can amount to ±220-280 ka. The modelling shows that small changes in assumed input values translate into large effects on absolute comminution age. To improve the accuracy of the technique and provide meaningful absolute comminution ages, much tighter constraints are required on the assumptions for input factors such as the fraction of α-recoil lost 234Th and the initial (234U/238U) ratio of the source material. In order to be able to directly compare calculated comminution ages produced by different research groups, the standardisation of pre-treatment procedures, recoil loss factor estimation and assumed input parameter values is required. We suggest a set of input parameter values for such a purpose. Additional considerations for calculating comminution ages of sediments deposited within large, semi-arid drainage basins are discussed.

Sediment deposition in the White River Reservoir, northwestern Wisconsin

USGS Publications Warehouse

Batten, W.G.; Hindall, S.M.

1980-01-01

The history of deposition in the White River Reservoir was reconstructed from a study of sediment in the reservoir. Suspended-sediment concentrations, particle size, and streamflow characteristics were measured at gaging stations upstream and downstream from the reservoir from November 1975 through September 1977. Characteristics of the sediments were determined from borings and samples taken while the reservoir was drained in September 1976. The sediment surface and the pre-reservoir topography were mapped. Sediment thickness ranged from less than 1 foot near the shore to more than 20 feet in the old stream channel. The original reservoir capacity and the volume of deposited sediment were calculated to be 815 acre-feet and 487 acre-feet, respectively. Sediment size ranged from clay and silt in the pool area to large cobbles and boulders at the upstream end of the reservoir. Analyses of all samples averaged 43 percent sand, 40 percent silt, and 17 percent clay, and particle size typically increased upstream. Cobbles, boulders, and gravel deposits were not sampled. The average density of the deposited sediment was about 80 pounds per cubic foot for the entire reservoir. The reservoir was able to trap about 80 percent of the sediment entering from upstream, early in its history. This trap efficiency has declined as the reservoir filled with sediment. Today (1976), it traps only sand and silt-sized sediment, or only about 20 percent of the sediment entering from upstream. Data collected during this study indicate that essentially all of the clay-sized sediment (<0.062 mm) passes through the reservoir. The gross rate of deposition was 7.0 acre-feet per year over the reservoir history, 1907-76. Rates during 1907-63 and 1963-76 were 7.4 and 5.7 acre-feet per year, respectively, determined by the cesium-137 method. Based on scant data, the average annual sediment yield of the total 279 square mile drainage area above the gaging station at the powerhouse was about 50 tons per square mile. Analysis of the drainage-basin characteristics indicates that most of this sediment was derived from less than 10 percent of the total drainage area and from steep unvegetated streambanks.

Amino acid epimerization implies rapid sedimentation rates in Arctic Ocean cores

USGS Publications Warehouse

Sejrup, H.P.; Miller, G.H.; Brigham-Grette, J.; Lovlie, R.; Hopkins, D.

1984-01-01

The palaeooceanography of the Arctic Ocean is less well known than any other ocean basin, due to difficulties in obtaining cores and in providing a secure chronological framework for those cores that have been raised. Most recent investigators have suggested that low sedimentation rates (0.05-0.1 cm kyr-1) have characterized the deep basins over the past 5 Myr (refs 1,2) despite the glacial-marine character of the sediment and proximity to major centres of shelf glaciation. These calculations have been primarily based on the down-core pattern in the inclination of magnetic minerals, supported by uranium-series, 14C and micropalaeontological evidence. Here we analyse amino acid diagnesis in foraminifera from two gravity cores raised from the floor of the Arctic Ocean, our results suggest that these cores span <200 kyr., conflicting with the earlier estimate of 3 Myr based on palaeomagnetic data. The chronology of other Arctic Ocean cores and previous palaeoenvironmental interpretations need re-evaluation. ?? 1984 Nature Publishing Group.

Bioconcentration of chlorinated hydrocarbons from sediment by oligochaetes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Connell, D.W.; Bowman, M.; Hawker, D.W.

1988-12-01

Previously published data on the accumulation of 15 chlorinated hydrocarbons from sediment by oligochaetes have been interpreted on the basis of bioconcentration from interstitial water. Calculation of the interstitial water concentration allowed determination of uptake and clearance rate constants together with bioconcentration factors (KB) for these compounds. These three factors each exhibited a systematic relationship to the octanol/water partition coefficient (KOW). The log KB versus log KOW relationship was roughly linear over the log KOW range from 4.4 to 6.4 and displayed an increasing nonlinear deviation for log KOW values greater than 6.4. These relationships are qualitatively similar to thosemore » established for other aquatic organisms where bioconcentration from water was the mechanism involved. This suggests that interstitial water may be the phase from which lipophilic compounds in sediment are bioconcentrated by oligochaetes. An expression relating the bioconcentration factor to the biotic concentration and various sediment characteristics has also been developed.« less

Simulations of dredged sediment spreading on a Posidonia oceanica meadow off the Ligurian coast, Northwestern Mediterranean.

PubMed

Capello, M; Cutroneo, L; Ferranti, M P; Budillon, G; Bertolotto, R M; Ciappa, A; Cotroneo, Y; Castellano, M; Povero, P; Tucci, S

2014-02-15

The sandy deposits from dredging can have negative effects on the environment such as increase in suspended solids in the water column and their consequent transport. An experimental study was conducted to characterize water masses, dynamics, and sedimentation rates on the Ligurian continental shelf (Italy), where both a sand deposit, that could be used for beach nourishment, and a nearby Posidonia oceanica meadow coexist. The environmental plan provides a mathematical simulation of the sediment-dispersion to evaluate the possible impact on the meadow. It has been calculated that the dredging could double the concentration of suspended particles, but its scheduling will preclude a sediment accumulation. All the information obtained from this work will be used to study the environmental feasibility of the sand deposit exploitation and as starting point for drawing up the monitoring plan in case of dredging. Copyright © 2013 Elsevier Ltd. All rights reserved.

A tale of two cores: Evaluation of 210Pb dating methods of salt marsh sediments for two cores collected 30 years apart

NASA Astrophysics Data System (ADS)

Fuller, C.; Drexler, J. Z.

2016-12-01

210Pb dating of wetland sediments is commonly used to constrain recent C accumulation rates and contaminant input histories. However, uncertainties in 210Pb-derived rates and validation of accumulation and accretion rates using an independent tracer are often not reported. We describe here 210Pb and 137Cs profiles in two cores from a salt marsh in south San Francisco Bay, California, collected in 1981 and 2011 within 5 m of each other, to compare and evaluate 210Pb dating methods. In the 1981 core, unsupported 210Pb (210PbXS) was detected to 12 cm and yielded mass accumulation rates (MAR) of 0.043 and 0.036 g/cm2/y using the Constant Flux-Constant Sedimentation method (CF:CS) and Constant Rate of Supply (CRS) methods, respectively. Accretion rates (S) of 0.17 (CF:CS) and 0.12 cm/y (CRS) were calculated from these MARs. The distinct 137Cs peak at 4-6 cm in the 1981 core is in good agreement with the210Pb-based 1963 depth (3.4 and 4 cm, CF:CS and CRS, respectively). 210PbXS was detectable to 18 cm in the 2011 core, and yielded a CF:CS MAR (0.077 g/cm2/y; S = 0.35 cm/y) that is about two times greater than the mass-weighted average CRS MAR (0.044 g/cm2/y; S = 0.16 cm/y). Broad subsurface maxima in 137Cs and 239Pu were observed between 16 and 24 cm in the 2011 core, which are 5 to 11 cm deeper than the 1963 depth calculated by the 2011 and 1981 210Pb-derived MARs. The apparent migration and broadening of bomb-fallout radionuclide peaks over 30 years negates their use in validating 210Pb dating. Because of low 210PbXS activities in both cores, the base of the 210PbXS profile and integrated activity used in CRS are underestimated, resulting in the lower CRS MARs that decrease with increasing depth. The range of MARs determined for two cores within 5 m but separated by 30 years will be used as an example to evaluate the uncertainties that need to be reported with C accumulation rates and contaminant histories derived from 210Pb dating of sediment archives.

Mercury cycling in stream ecosystems. 2. Benthic methylmercury production and bed sediment - Pore water partitioning

USGS Publications Warehouse

Marvin-DiPasquale, Mark; Lutz, Michelle A; Brigham, Mark E.; Krabbenhoft, David P.; Aiken, George R.; Orem, William H.; Hall, Britt D.

2009-01-01

Mercury speciation, controls on methylmercury (MeHg) production, and bed sediment−pore water partitioning of total Hg (THg) and MeHg were examined in bed sediment from eight geochemically diverse streams where atmospheric deposition was the predominant Hg input. Across all streams, sediment THg concentrations were best described as a combined function of sediment percent fines (%fines; particles < 63 μm) and organic content. MeHg concentrations were best described as a combined function of organic content and the activity of the Hg(II)-methylating microbial community and were comparable to MeHg concentrations in streams with Hg inputs from industrial and mining sources. Whole sediment tin-reducible inorganic reactive Hg (Hg(II)R) was used as a proxy measure for the Hg(II) pool available for microbial methylation. In conjunction with radiotracer-derived rate constants of 203Hg(II) methylation, Hg(II)R was used to calculate MeHg production potential rates and to explain the spatial variability in MeHg concentration. The %Hg(II)R (of THg) was low (2.1 ± 5.7%) and was inversely related to both microbial sulfate reduction rates and sediment total reduced sulfur concentration. While sediment THg concentrations were higher in urban streams, %MeHg and %Hg(II)R were higher in nonurban streams. Sediment pore water distribution coefficients (log Kd’s) for both THg and MeHg were inversely related to the log-transformed ratio of pore water dissolved organic carbon (DOC) to bed sediment %fines. The stream with the highest drainage basin wetland density also had the highest pore water DOC concentration and the lowest log Kd’s for both THg and MeHg. No significant relationship existed between overlying water MeHg concentrations and those in bed sediment or pore water, suggesting upstream sources of MeHg production may be more important than local streambed production as a driver of water column MeHg concentration in drainage basins that receive Hg inputs primarily from atmospheric sources.

Determining the times and distances of particle transit in a mountain stream using fallout radionuclides

NASA Astrophysics Data System (ADS)

Bonniwell, Everett C.; Matisoff, Gerald; Whiting, Peter J.

1999-02-01

Targeting of erosion and pollution control programs is much more effective if the time for fine particles to be transported through a watershed, the travel distance, the proportions of old and new sediment in suspension, and the rate of erosion of the landscape can be estimated. In this paper we present a novel technique for tracing suspended sediment in a mountain stream using fallout radionuclides sorbed to sediment. Atmospherically-delivered 7Be, 210Pb, and 137Cs accumulate in the snowpack, are released with its melting and sorb to fine particulates, a portion of which are carried downslope into stream channels. The half-life of cosmogenic 7Be is short (53.4 days), thus, sediment residing on the stream bed should contain little of the radionuclide. The different signatures of newly delivered sediment from the landscape with its 7Be tag and older untagged sediment from the channel is the basis for the tracing. The total flux of such radionuclides, compared to the inventory in the soil, permits estimates of the rates of erosion of the landscape. Fine suspended particulates in the Gold Fork River, ID, are transported downstream through the drainage in one or more steps having lengths of tens of kilometers. Length of the step decreases from about 60 km near the peak of the hydrograph to about 12 km near baseflow. The percent of sediment in suspension that is `new' (i.e., recently delivered from the landscape) ranges from 96 to 12%. The remaining sediment is resuspended older channel sediment. Residence times for particulates range from 1.6 days, early in the hydrograph at the upper site, to 103 days late in the hydrograph at the lowest elevation location. Rates of erosion of fine sediment calculated from the flux of radionuclides average 0.0023 cm/year. The long distance transport of fine particles suggests that delivery through the Gold Fork drainage to the basin outlet is fairly rapid once particles reach the channel and perhaps is also rapid in similar and smaller basins.

Numerical modelling study of gully recharge and debris flows in Haida Gwaii, British Columbia

NASA Astrophysics Data System (ADS)

Martin, Yvonne; Johnson, Edward; Chaikina, Olga

2015-04-01

In high mountains, debris flows are a major process responsible for transferring sediment to more downstream fluvial reaches. This sediment transfer begins on mountain hillslopes where various mass wasting processes move sediment from hillslopes to uppermost reaches of the channel system (these reaches are herein referred to as gullies and only experience water flow during high intensity precipitation events). Sediment recharge into gullies, which has received minimal attention in the scientific literature, refers to the transfer of sediment and other debris from surrounding hillslopes into gullies (Jakob and Oden, 2005). Debris flow occurrence and debris flow volumes depend on some precipitation threshold as well as volumes of material contained in the particular gully. For example, if one debris flow has removed all of the accumulated material from the gully, then any subsequent debris flow will be smaller if enough time has not yet passed for notable sediment recharge. Herein, we utilize the numerical model of landscape development, LandMod (Martin, 1998; Dadson and Church, 2005; Martin, 2007), to explore connections between hillslope processes, gully recharge rates, and transfer of sediment to downstream channel reaches in the Haida Gwaii, British Columbia. Hillslope processes in the model include shallow landsliding, bedrock failures and weathering. The updated debris flow algorithm is based on extensive field data available for debris flows in Haida Gwaii (e.g., Rood, 1984; Oden, 1994; Jakob and Oden, 2005), as well as theoretical considerations based on debris flow studies. The most significant model extension is the calculation of gully recharge rates; for each gully, the total accumulated sediment in gullies at each time step is determined using a power-law relation for area-normalized recharge rate versus elapsed time since the last debris flow. Thus, when the stochastic driver for debris flow occurrence triggers an event, the amount of stored material is known and can be transferred and deposited along the channel system. Results show that the size distribution of debris flows and sediment transfers from gullies to downstream reaches are modified by the inclusion of a module that accounts for sediment recharge when compared to model runs that do not consider gully recharge.

Combined Climate and Flow Abstraction Impacts on an Aggrading Alpine River

NASA Astrophysics Data System (ADS)

Bakker, M.; Costa, A.; Silva, T. A.; Stutenbecker, L.; Girardclos, S.; Loizeau, J. L.; Molnar, P.; Schlunegger, F.; Lane, S. N.

2017-12-01

Recent climatic warming and associated glacial retreat may have a large impact on sediment release and transfer in Alpine river basins. In parallel, the sediment transport capacity of many European Alpine streams is affected by hydropower exploitation, notably where flow is abstracted but the sediment supply to the headwaters is maintained at flow intakes. Here, we investigate the combined effects of climate change and flow abstraction on morphodynamics and sediment transfer in one such Alpine stream, the Borgne River, Switzerland. A unique dataset forms the basis for determining sediment deposition and transfer: (1) a set of high resolution Digital Elevation Models (DEMs) of braided river reaches is derived through applying Structure from Motion (SfM) photogrammetry to archival aerial photographs available for the period 1959-2014; (2) flow intake management data is used for the reconstruction of (up- and downstream) discharge and sediment supply since 1977. Subsequently we use bedload transport capacity calculations and climate data to assess their relative impact on the system evolution over the last 25 years. From the historical DEMs we find considerable aggradation of the river bed (up to 5 meters) since the onset of flow abstraction in 1963. Rapid and widespread aggradation however did not commence until the onset of glacier retreat in the late 1980s and the dry and notably warm years of the early 1990s. This aggradation coincided with an increase in sediment supply, although it accounts for only c. 25% of supplied material, the remainder was transferred through the studied reaches. Flow abstraction reduces transport capacity by an order of magnitude but the residual transport rates are close to sediment supply rates, which is why significant transport remains. However, the reduction in transport capacity due to direct human impacts in basin hydrology (flow abstraction) makes the system much more sensitive to changes in climate-driven hydrological variability and climate induced changes in intake management and sediment supply rates. This was exemplified by an increasingly strong climate (winter precipitation and summer temperature) influence on the delivery of glacially derived sediment.

Estuaries as Filters: The Role of Tidal Marshes in Trace Metal Removal

PubMed Central

Teuchies, Johannes; Vandenbruwaene, Wouter; Carpentier, Roos; Bervoets, Lieven; Temmerman, Stijn; Wang, Chen; Maris, Tom; Cox, Tom J. S.; Van Braeckel, Alexander; Meire, Patrick

2013-01-01

Flux calculations demonstrate that many estuaries are natural filters for trace metals. Yet, the underlying processes are poorly investigated. In the present study, it was hypothesized that intertidal marshes contribute significantly to the contaminant filter function of estuaries. Trace metal concentrations and sediment characteristics were measured along a transect from the subtidal, over an intertidal flat and marsh to a restored marsh with controlled reduced tide. Metal concentrations in the intertidal and restored marsh were found to be a factor two to five higher than values in the subtidal and intertidal flat sediments. High metal concentrations and high accretion rates indicate a high metal accumulation capacity of the intertidal marshes. Overbank sedimentation in the tidal marshes of the entire estuary was calculated to remove 25% to 50% of the riverine metal influx, even though marshes comprise less than 8% of the total surface of the estuary. In addition, the large-scale implementation of planned tidal marsh restoration projects was estimated to almost double the trace metal storage capacity of the present natural tidal marshes in the estuary. PMID:23950927

Effects of Aggregation on Blood Sedimentation and Conductivity

PubMed Central

Zhbanov, Alexander; Yang, Sung

2015-01-01

The erythrocyte sedimentation rate (ESR) test has been used for over a century. The Westergren method is routinely used in a variety of clinics. However, the mechanism of erythrocyte sedimentation remains unclear, and the 60 min required for the test seems excessive. We investigated the effects of cell aggregation during blood sedimentation and electrical conductivity at different hematocrits. A sample of blood was drop cast into a small chamber with two planar electrodes placed on the bottom. The measured blood conductivity increased slightly during the first minute and decreased thereafter. We explored various methods of enhancing or retarding the erythrocyte aggregation. Using experimental measurements and theoretical calculations, we show that the initial increase in blood conductivity was indeed caused by aggregation, while the subsequent decrease in conductivity resulted from the deposition of erythrocytes. We present a method for calculating blood conductivity based on effective medium theory. Erythrocytes are modeled as conducting spheroids surrounded by a thin insulating membrane. A digital camera was used to investigate the erythrocyte sedimentation behavior and the distribution of the cell volume fraction in a capillary tube. Experimental observations and theoretical estimations of the settling velocity are provided. We experimentally demonstrate that the disaggregated cells settle much slower than the aggregated cells. We show that our method of measuring the electrical conductivity credibly reflected the ESR. The method was very sensitive to the initial stage of aggregation and sedimentation, while the sedimentation curve for the Westergren ESR test has a very mild slope in the initial time. We tested our method for rapid estimation of the Westergren ESR. We show a correlation between our method of measuring changes in blood conductivity and standard Westergren ESR method. In the future, our method could be examined as a potential means of accelerating ESR tests in clinical practice. PMID:26047511

A new method for mapping variability in vertical seepage flux in streambeds

NASA Astrophysics Data System (ADS)

Chen, Xunhong; Song, Jinxi; Cheng, Cheng; Wang, Deming; Lackey, Susan O.

2009-05-01

A two-step approach was used to measure the flux across the water-sediment interface in river channels. A hollow tube was pressed into the streambed and an in situ sediment column of the streambed was created inside the tube. The hydraulic gradient between the two ends of the sediment column was measured. The vertical hydraulic conductivity of the sediment column was determined using a falling-head permeameter test in the river. Given the availability of the hydraulic gradient and vertical hydraulic conductivity of the streambed, Darcy’s law was used to calculate the specific discharge. This approach was applied to the Elkhorn River and one tributary in northeastern Nebraska, USA. The results suggest that the magnitude of the vertical flux varied greatly within a short distance. Furthermore, the flux can change direction from downward to upward between two locations only several meters apart. This spatial pattern of variation probably represents the inflow and outflow within the hyporheic zone, not the regional ambient flow systems. In this study, a thermal infrared camera was also used to detect the discharge locations of groundwater in the streambed. After the hydraulic gradient and the vertical hydraulic conductivity were estimated from the groundwater spring, the discharge rate was calculated.

Radioactivity and metal concentrations in marine sediments associated with mining activities in Ierissos Gulf, North Aegean Sea, Greece.

PubMed

Pappa, F K; Tsabaris, C; Ioannidou, A; Patiris, D L; Kaberi, H; Pashalidis, I; Eleftheriou, G; Androulakaki, E G; Vlastou, R

2016-10-01

Marine sediment samples were collected from Ierissos Gulf, N Aegean Sea, close to the coastal mining facilities. Measurements of radionuclide and metal concentrations, mineral composition and grain size distribution were performed. The concentrations of (226)Ra, (235)U and trace metals showed enhanced values in the port of Stratoni compared with those obtained near to Ierissos port. The dose rates received by marine biota were also calculated by the ERICA Assessment Tool and the results indicated no significant radiological risk. Copyright © 2016 Elsevier Ltd. All rights reserved.

Scale-Dependent Rates of Uranyl Surface Complexation Reaction in Sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chongxuan; Shang, Jianying; Kerisit, Sebastien N.

Scale-dependency of uranyl[U(VI)] surface complexation rates was investigated in stirred flow-cell and column systems using a U(VI)-contaminated sediment from the US Department of Energy, Hanford site, WA. The experimental results were used to estimate the apparent rate of U(VI) surface complexation at the grain-scale and in porous media. Numerical simulations using molecular, pore-scale, and continuum models were performed to provide insights into and to estimate the rate constants of U(VI) surface complexation at the different scales. The results showed that the grain-scale rate constant of U(VI) surface complexation was over 3 to 10 orders of magnitude smaller, dependent on themore » temporal scale, than the rate constant calculated using the molecular simulations. The grain-scale rate was faster initially and slower with time, showing the temporal scale-dependency. The largest rate constant at the grain-scale decreased additional 2 orders of magnitude when the rate was scaled to the porous media in the column. The scaling effect from the grain-scale to the porous media became less important for the slower sorption sites. Pore-scale simulations revealed the importance of coupled mass transport and reactions in both intragranular and inter-granular domains, which caused both spatial and temporal dependence of U(VI) surface complexation rates in the sediment. Pore-scale simulations also revealed a new rate-limiting mechanism in the intragranular porous domains that the rate of coupled diffusion and surface complexation reaction was slower than either process alone. The results provided important implications for developing models to scale geochemical/biogeochemical reactions.« less

Impact of sedimentation and particle fragmentation on the collapse of explosive volcanic eruption columns.

NASA Astrophysics Data System (ADS)

Michaud-Dubuy, A.; Carazzo, G.; Kaminski, E. C.

2017-12-01

High-velocity atmospheric turbulent jets produced by explosive volcanic eruptions can form a high buoyant Plinian plume or produce pyroclastic density currents (PDCs) when the column collapses. A major goal of physical volcanology is to determine the limit between the two flow regimes, as a function of source conditions. But their highly non-linear dynamics makes this prediction particularly difficult. Classically, in the so-called "dusty gas" hypothesis, the regime boundary is calculated as a function of the eruptive mass flux and the amount of gas dissolved in the magma. Here, we relax this hypothesis and account for the differential behavior between gas and particle, i.e. sedimentation. The sedimentation rate is calculated as a function of the particle size, which introduces the total grain-size distribution (TGSD) as a new model parameter. Here we further consider power-law TGSDs characterized by an exponent D. For low eruption rates (Vulcanian and sub-Plinian eruptions), the loss of particles by sedimentation is so large that it drains out the thermal reservoir available to heat the engulfed cold atmospheric air, which favors PDCs production. In powerful Plinian eruptions with a mass flux greater than 107 kg/s, the loss of particles by sedimentation is less important and its dominant effect is to decrease the column mass flux during its rise, which favors the formation of stable columns. In this case, we further obtain that coarse distributions promote the formation of stable plumes, a result at odds with previous studies. To interpret this conclusion, we reconsider the effect of gas entrapment by pumice at fragmentation and show that in general it has a dominant role on column collapse compared to particle sedimentation. However, for D values < 2.8, sedimentation and gas entrapment are of equal importance and act together to prevent the production of stable plumes. This latter conclusion is consistent with field data. We compare the predictions of the model including gas entrapment and sedimentation to two well constrained historical events, the Taupo 186 AD and Vesuvius 79 AD eruptions. In both cases, we obtain that the model should take into account not solely gas entrapment but also the open porosity to accurately reproduce field data.

Effect of a dual inlet channel on cell loading in microfluidics.

PubMed

Yun, Hoyoung; Kim, Kisoo; Lee, Won Gu

2014-11-01

Unwanted sedimentation and attachment of a number of cells onto the bottom channel often occur on relatively large-scale inlets of conventional microfluidic channels as a result of gravity and fluid shear. Phenomena such as sedimentation have become recognized problems that can be overcome by performing microfluidic experiments properly, such as by calculating a meaningful output efficiency with respect to real input. Here, we present a dual-inlet design method for reducing cell loss at the inlet of channels by adding a new " upstream inlet " to a single main inlet design. The simple addition of an upstream inlet can create a vertically layered sheath flow prior to the main inlet for cell loading. The bottom layer flow plays a critical role in preventing the cells from attaching to the bottom of the channel entrance, resulting in a low possibility of cell sedimentation at the main channel entrance. To provide proof-of-concept validation, we applied our design to a microfabricated flow cytometer system (μFCS) and compared the cell counting efficiency of the proposed μFCS with that of the previous single-inlet μFCS and conventional FCS. We used human white blood cells and fluorescent microspheres to quantitatively evaluate the rate of cell sedimentation in the main inlet and to measure fluorescence sensitivity at the detection zone of the flow cytometer microchip. Generating a sheath flow as the bottom layer was meaningfully used to reduce the depth of field as well as the relative deviation of targets in the z-direction (compared to the x-y flow plane), leading to an increased counting sensitivity of fluorescent detection signals. Counting results using fluorescent microspheres showed both a 40% reduction in the rate of sedimentation and a 2-fold higher sensitivity in comparison with the single-inlet μFCS. The results of CD4(+) T-cell counting also showed that the proposed design results in a 25% decrease in the rate of cell sedimentation and a 28% increase in sensitivity when compared to the single-inlet μFCS. This method is simple and easy to use in design, yet requires no additional time or cost in fabrication. Furthermore, we expect that this approach could potentially be helpful for calculating exact cell loading and counting efficiency for a small input number of cells, such as primary cells and rare cells, in microfluidic channel applications.

Vertical and lateral flux on the continental slope off Pakistan: correlation of sediment core and trap results

NASA Astrophysics Data System (ADS)

Schulz, H.; von Rad, U.

2014-06-01

Due to the lack of bioturbation, the varve-laminated muds from the oxygen minimum zone (OMZ) off Pakistan provide a unique opportunity to precisely determine the vertical and lateral sediment fluxes in the nearshore part of the northeastern Arabian Sea. West of Karachi (Hab area), the results of two sediment trap stations (EPT and WPT) were correlated with 16 short sediment cores on a depth transect crossing the OMZ. The top of a distinct, either reddish- or light-gray silt layer, 210Pb-dated as AD 1905 ± 10, was used as an isochronous stratigraphic marker bed to calculate sediment accumulation rates. In one core, the red and gray layer were separated by a few (5-10) thin laminae. According to our varve model, this contributes < 10 years to the dating uncertainty, assuming that the different layers are almost synchronous. We directly compared the accumulation rates with the flux rates from the sediment traps that collected the settling material within the water column above. All traps on the steep Makran continental slope show exceptionally high, pulsed winter fluxes of up to 5000 mg m-2 d-1. Based on core results, the flux at the seafloor amounts to 4000 mg m-2 d-1 and agrees remarkably well with the bulk winter flux of material, as well as with the flux of the individual bulk components of organic carbon, calcium carbonate and opal. However, due to the extreme mass of remobilized matter, the high winter flux events exceeded the capacity of the shallow traps. Based on our comparisons, we argue that high-flux events must occur regularly during winter within the upper OMZ off Pakistan to explain the high accumulations rates. These show distribution patterns that are a negative function of water depth and distance from the shelf. Some of the sediment fractions show marked shifts in accumulation rates near the lower boundary of the OMZ. For instance, the flux of benthic foraminifera is lowered but stable below ~1200-1300 m. However, flux and sedimentation in the upper eastern Makran area are dominated by the large amount of laterally advected fine-grained material and by the pulsed nature of the resuspension events at the upper margin during winter.

Importance of Dissolved Neutral Hg-Sulfides, Energy Rich Organic Matter and total Hg Concentrations for Methyl Mercury Production in Sediments

NASA Astrophysics Data System (ADS)

Drott, A.; Skyllberg, U.

2007-12-01

Methyl mercury (MeHg) is the mercury form that biomagnifies to the greatest extent in aquatic food webs. Therefore information about factors determining MeHg concentrations is critical for accurate risk assessment of contaminated environments. The concentration of MeHg in wetlands and sediments is the net result of: 1) methylation rates, 2) demethylation rates, and 3) input/output processes. In this study, the main controls on Hg methylation rates and total concentrations of MeHg, were investigated at eight sites in Sweden with sediments that had been subjected to local Hg contamination either as Hg(0), or as phenyl-Hg. Sediments were selected to represent a gradient in total Hg concentration, temperature climate, salinity, primary productivity, and organic C content and quality. Most sediments were high in organic matter content due to wood fibre efflux from pulp and paper industry. The pore water was analysed for total Hg, MeHg, DOC, H2S(aq), pH, DOC, Cl and Br. The chemical speciation of Hg(II) and MeHg in pore water was calculated using equilibrium models. Potential methylation and demethylation rates in sediments were determined in incubation experiments at 23° C under N2(g) for 48 h, after addition of isotopically enriched 201Hg(II) and Me204Hg. In all surface (0-20 cm) sediments there was a significant (p<0.001) positive relationship between the experimentally determined specific potential methylation rate constant (Km, day-1) and % MeHg (concentrations of MeHg normalized to total Hg) in the sediment. This indicates that MeHg production overruled degradation and input/output processes of MeHg in surface sediments, and that % MeHg in surface sediments may be used as a proxy for net production of MeHg. To our knowledge, these are the first data showing significant positive relationships between short term (48 h) MeHg production and longer term accumulation of MeHg, across a range of sites with different properties (1). If MeHg was not normalized to total Hg, the relationship was not significant. For sub-sets of brackish waters (p<0.001, n=23), southern, high-productivity freshwaters (p<0.001, n=20) as well as northern, low-productivity freshwater (p=0.048, n=6), the sum of neutral Hg-sulfides [Hg(SH)20 (aq)] and [HgS0 (aq)] in the sediment pore water was significantly, positively correlated with both the potential methylation rate constant (Km) and total MeHg concentrations (2). This indicates that methylating sulphate reducing bacteria passively take up neutral Hg-sulfides, which are transformed to MeHg. Differences in slopes of the relationships were explained by differences in primary productivity and availability of energy-rich organic matter to methylating bacteria. High primary productivity at southern freshwater sites, reflected by a low C/N ratio (large contribution from free living algae and bacteria) in the sediment and a high annual temperature sum, resulted in high methylation rates. In conclusion, concentrations of neutral Hg-sulfides and availability of energy rich organic matter, but also total Hg concentrations in sediments are important factors behind net production and accumulation of MeHg . References: (1) Drott et. al. submitted, (2) Drott, A.; Lambertsson, L.; Björn, E.; Skyllberg, U. Importance of dissolved neutral mercury sulfides for methyl mercury production in contaminated sediments. Environmental Science & Technology 2007, 41, 2270-2276.

Dynamic simulations of the inhomogeneous sedimentation of rigid fibres

NASA Astrophysics Data System (ADS)

Butler, Jason E.; Shaqfeh, Eric S. G.

2002-10-01

We have simulated the dynamics of suspensions of fibres sedimenting in the limit of zero Reynolds number. In these simulations, the dominant inter-particle force arises from hydrodynamic interactions between the rigid, non-Brownian fibres. The simulation algorithm uses slender-body theory to model the linear and rotational velocities of each fibre. To include far-field interactions between the fibres, the line distribution of force on each fibre is approximated by making a Legendre polynomial expansion of the disturbance velocity on the fibre, where only the first two terms of the expansion are retained in the calculation. Thus, the resulting linear force distribution can be specified completely by a centre-of-mass force, a couple, and a stresslet. Short-range interactions between particles are included using a lubrication approximation, and an infinite suspension is simulated by using periodic boundary conditions. Our numerical results confirm that the sedimentation of these non-spherical, orientable particles differs qualitatively from the sedimentation of spherical particles. The simulations demonstrate that an initially homogeneous, settling suspension develops clusters, or streamers, which are particle rich surrounded by clarified fluid. The instability which causes the heterogeneous structure arises solely from hydrodynamic interactions which couple the particle orientation and the sedimentation rate in particle clusters. Depending upon the concentration and aspect ratio, the formation of clusters of particles can enhance the sedimentation rate of the suspension to a value in excess of the maximum settling speed of an isolated particle. The suspension of fibres tends to orient with gravity during the sedimentation process. The average velocities and orientations, as well as their distributions, compare favourably with previous experimental measurements.

Calculating sediment discharge from a highway construction site in central Pennsylvania

USGS Publications Warehouse

Reed, L.A.; Ward, J.R.; Wetzel, K.L.

1985-01-01

The Pennsylvania Department of Transportation, the Federal Highway Administration, and the U.S. Geological Survey have cooperated in a study to evaluate two methods of predicting sediment yields during highway construction. Sediment yields were calculated using the Universal Soil Loss and the Younkin Sediment Prediction Equations. Results were compared to the actual measured values, and standard errors and coefficients of correlation were calculated. Sediment discharge from the construction area was determined for storms that occurred during construction of Interstate 81 in a 0.38-square mile basin near Harrisburg, Pennsylvania. Precipitation data tabulated included total rainfall, maximum 30-minute rainfall, kinetic energy, and the erosive index of the precipitation. Highway construction data tabulated included the area disturbed by clearing and grubbing, the area in cuts and fills, the average depths of cuts and fills, the area seeded and mulched, and the area paved. Using the Universal Soil Loss Equation, sediment discharge from the construction area was calculated for storms. The standard error of estimate was 0.40 (about 105 percent), and the coefficient of correlation was 0.79. Sediment discharge from the construction area was also calculated using the Younkin Equation. The standard error of estimate of 0.42 (about 110 percent), and the coefficient of correlation of 0.77 are comparable to those from the Universal Soil Loss Equation.

Deep-sea spherules from Pacific clay: mass distribution and influx rate

USGS Publications Warehouse

Murrell, M.T.; Davis, P.A.; Nishiizumi, K.; Millard, H.T.

1980-01-01

From 411 kg of Pacific clay, 22 mg of stony spherules and 50 mg of iron spherules larger than 150 ??m were concentrated. The extraterrestrial origin of these particles was evaluated with the aid of both optical and electron microscopy as well as atomic absorption elemental analysis. The integral number (N) of stony particles from this sediment in the mass (M) range 20-300 ??g is given by N( > M(g)) = 5.13 ?? 10-6 ?? M-1.65. The world-wide influx rate of stony particles in the mass range which survive atmospheric heating and ocean sediment storage is calculated to be 90 tons/yr. The relative contributions of ablation debris vs fused interplanetary dust to the influx of stony spherules is discussed, but as yet the question remains unanswered. ?? 1980.

Ammonia Gas Transport and Reactions in Unsaturated Sediments: Implications for Use as an Amendment to Immobilize Inorganic Contaminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong, Lirong; Szecsody, James E.; Truex, Michael J.

Use of gas-phase amendments for in situ remediation of inorganic contaminants in unsaturated sediments of the vadose zone may be advantageous, but there has been limited development and testing of gas remediation technologies. Treatment with ammonia gas has been studied and has a potential for use in treating inorganic contaminants such as uranium because it induces a high pore-water pH causing mineral dissolution and subsequent formation of stable precipitates that decrease the mobility of some contaminants. For field application, knowledge of ammonia transport and the geochemical reactions induced by ammonia is needed. Laboratory studies were conducted to support calculations neededmore » for field treatment design, to quantify advective and diffusive ammonia transport in unsaturated sediments, to evaluate reactions among gas, sediment, and water, and to study reaction-induced pore-water chemistry changes as a function of ammonia delivery conditions. Ammonia gas quickly partitions into sediment pore water and increases pH up to 13.2. Injected ammonia gas front movement can be reasonably predicted by gas flow rate and equilibrium partitioning. The ammonia gas diffusion rate is a function of the water content in the sediment. Measured diffusion front movement was 0.05, 0.03, and 0.02 cm/hr. in sediments with 2.0%, 8.7%, and 13.0% water content, respectively. Sodium, aluminum, and silica pore-water concentrations increase on exposure to ammonia and then decline as aluminosilicates precipitate with declining pH. When uranium is present in the sediment and pore water, up to 85% of the water-leachable uranium was immobilized by ammonia treatment.« less

Wetland management reduces sediment and nutrient loading to the upper Mississippi river.

PubMed

Kreiling, Rebecca M; Schubauer-Berigan, Joseph P; Richardson, William B; Bartsch, Lynn A; Hughes, Peter E; Cavanaugh, Jennifer C; Strauss, Eric A

2013-01-01

Restored riparian wetlands in the Upper Mississippi River basin have potential to remove sediment and nutrients from tributaries before they flow into the Mississippi River. For 3 yr we calculated retention efficiencies of a marsh complex, which consisted of a restored marsh and an adjacent natural marsh that were connected to Halfway Creek, a small tributary of the Mississippi. We measured sediment, N, and P removal through a mass balance budget approach, N removal through denitrification, and N and P removal through mechanical soil excavation. The marsh complex had average retention rates of approximately 30 Mg sediment ha yr, 26 kg total N ha yr, and 20 kg total P ha yr. Water flowed into the restored marsh only during high-discharge events. Although the majority of retention occurred in the natural marsh, portions of the natural marsh were hydrologically disconnected at low discharge due to historical over-bank sedimentation. The natural marsh removed >60% of sediment, >10% of P, and >5% of N loads (except the first year, when it was a N source). The marsh complex was a source of NH and soluble reactive P. The average denitrification rate for the marsh complex was 2.88 mg N m h. Soil excavation removed 3600 Mg of sediment, 5.6 Mg of N, and 2.7 Mg of P from the restored marsh. The marsh complex was effective in removing sediment and nutrients from storm flows; however, retention could be increased if more water was diverted into both restored and natural marshes before entering the river. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

An Analysis of Denitrification and Anammox Processes in Sediments Underneath Oyster Aquaculture

NASA Astrophysics Data System (ADS)

Mazur, C. I.; Edgcomb, V. P.; Rogers, D.; Cobban, A.

2016-02-01

Oysters play a very important role in the removal of nitrogen from eutrophic waters. While the amount of nitrogen that is converted into biomass is well studied, little is known about the additional amount of nitrogen that may be removed from the sediments due to the presence of oysters. The purpose of this project was to examine microbial processes that occur in sediments under oyster aquaculture cages in local ponds/estuaries, and to measure the rates of key processes associated with nitrogen removal. Little Pond and West Falmouth (Cape Cod, Massachusetts) are coastal waterways that are degraded due to nitrogen loading. Oyster aquaculture operations have been installed at both sites to help clean up those eutrophic estuaries. We measured nitrate and ammonia concentrations in porewaters and water columns. Direct measurements of rates of denitrification and anaerobic ammonium oxidation (anammox) were completed with Membrane Inlet Mass Spectroscopy (MIMS). Genes and transcripts associated with denitrification and anammox in sediments under oysters and at control sites were calculated using quantitative PCR. Results suggest that rates of denitrification are 2-30 times higher under oysters than at control sites, and gene expression patterns provide a second line of support for those findings. The ultimate goal of the project is to provide data to improve models of the nitrogen removal potential of shellfish aquaculture as a possible remediation strategy for improving the quality of eutrophic coastal waters.

Sediment rating curve & Co. - a contest of prediction methods

NASA Astrophysics Data System (ADS)

Francke, T.; Zimmermann, A.

2012-04-01

In spite of the recent technological progress in sediment monitoring, often the calculation of sediment yield (SSY) still relies on intermittent measurements because of the use of historic records, instrument-failure in continuous recording or financial constraints. Therefore, available measurements are usually inter- and even extrapolated using the sediment rating curve approach, which uses continuously available discharge data to predict sediment concentrations. Extending this idea by further aspects like the inclusion of other predictors (e.g. rainfall, discharge-characteristics, etc.), or the consideration of prediction uncertainty led to a variety of new methods. Now, with approaches such as Fuzzy Logic, Artificial Neural Networks, Tree-based regression, GLMs, etc., the user is left to decide which method to apply. Trying multiple approaches is usually not an option, as considerable effort and expertise may be needed for their application. To establish a helpful guideline in selecting the most appropriate method for SSY-computation, we initiated a study to compare and rank available methods. Depending on problem attributes like hydrological and sediment regime, number of samples, sampling scheme, and availability of ancillary predictors, the performance of different methods is compared. Our expertise allowed us to "register" Random Forests, Quantile Regression Forests and GLMs for the contest. To include many different methods and ensure their sophisticated use we invite scientists that are willing to benchmark their favourite method(s) with us. The more diverse the participating methods are, the more exciting the contest will be.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chapelle, F.H.; Zelibor, J.L. Jr.; Grimes, D.J.

Nineteen cores of unconsolidated Coastal Plain sediments obtained from depths of 14 to 182 m below land surface near Waldorf, Maryland, were collected and examined for metabolically active bacteria. The age of the sediments cored range from Miocene to Early Cretaceous. Acridine orange direct counts of total (viable and nonviable) bacteria in core subsamples ranged from 10/sup 8/ to 10/sup 4/ bacteria/g of dry sediment. Direct counts of viable bacteria ranged from 10/sup 6/ to 10/sup 3/ bacteria/g of dry sediment. Three cores contained viable methanogenic bacteria, and seven cores contained viable sulfate-reducing bacteria. The observed presence of bacteria inmore » these sediments suggest that hetrotrophic bacterial metabolism, with lignitic organic material as the primary substrate, is a plausible source of CO/sub 2/ to ground water. However, the possibility that abiotic processes also produce CO/sub 2/ cannot be rules out. Estimated rates of CO/sub 2/ production in the noncalcareous Magothy/Upper Patapsco and Lower Patapsco aquifers based on mass balance of dissolved inorganic carbon, ground water flow rates, and flow path segment lengths are in the range 10/sup -3/ to 10/sup -5/ mmol L/sup -1/ yr/sup -1/. Isotope balance calculations suggest that aquifer-generated CO/sub 2/ is much heavier isotopically ( approx. - 10 to + 5 per mil) than lignite ( approx. - 24 per mil) present in these sediments. This may reflect isotopic fractionation during methanogenesis and possibly other bacterially mediated processes.« less

Constraints on Water Reservoir Lifetimes From Catchment-Wide 10Be Erosion Rates—A Case Study From Western Turkey

NASA Astrophysics Data System (ADS)

Heineke, Caroline; Hetzel, Ralf; Akal, Cüneyt; Christl, Marcus

2017-11-01

The functionality and retention capacity of water reservoirs is generally impaired by upstream erosion and reservoir sedimentation, making a reliable assessment of erosion indispensable to estimate reservoir lifetimes. Widely used river gauging methods may underestimate sediment yield, because they do not record rare, high-magnitude events and may underestimate bed load transport. Hence, reservoir lifetimes calculated from short-term erosion rates should be regarded as maximum values. We propose that erosion rates from cosmogenic 10Be, which commonly integrate over hundreds to thousands of years, are useful to complement short-term sediment yield estimates and should be employed to estimate minimum reservoir lifetimes. Here we present 10Be erosion rates for the drainage basins of six water reservoirs in Western Turkey, which are located in a tectonically active region with easily erodible bedrock. Our 10Be erosion rates for these catchments are high, ranging from ˜170 to ˜1,040 t/km2/yr. When linked to reservoir volumes, they yield minimum reservoir lifetimes between 25 ± 5 and 1,650 ± 360 years until complete filling, with four reservoirs having minimum lifespans of ≤110 years. In a neighboring region with more resistant bedrock and less tectonic activity, we obtain much lower catchment-wide 10Be erosion rates of ˜33 to ˜95 t/km2/yr, illustrating that differences in lithology and tectonic boundary conditions can cause substantial variations in erosion even at a spatial scale of only ˜50 km. In conclusion, we suggest that both short-term sediment yield estimates and 10Be erosion rates should be employed to predict the lifetimes of reservoirs.

Vertical suspended sediment fluxes observed from a formation of underwater gliders

NASA Astrophysics Data System (ADS)

Merckelbach, Lucas; Riethmueller, Rolf

2014-05-01

In order to understand and predict the pathways and deposition of fine sediments in coastal regions valid parameterisations of the fluxes across interfaces (sea bed - water column or a pycnocline) are paramount. Traditionally, these parameterisations are based on the concept of a critical shear stress, but more recently a probabilistic approach has been proposed, in which the resuspension of sediment is assumed to have a certain likelihood, depending on the external forcing. Both approaches find their justification, to some extent, from the results of laboratory experiments, however, in-situ data, essential for model validation, are scarce. In this study we develop a field method to estimate the (fine) sediment fluxes between the seabed and the water column, and across the pycnocline. The method is applied to a stratified shallow sea (the North Sea in Summer). In order to assess the results, these fluxes are interpreted in terms of bottom shear stress and current shear between upper and lower layer, respectively. The method was tested in an experiment with two underwater gliders in Summer 2013 in the German Bight. Both gliders were equipped with optical backscatter sensors, the measurements of which serve as a proxy for suspended sediment concentration. The profiling character of the gliders allows to calculate the rate of change of the layer-averaged sediment concentration, as observed by the platform. The local, Lagrangian rate of change of sediment concentration is the balance between the fluxes across the layer's interfaces. Due to a horizontal speed of the glider of about 0.5 m/s, horizontal gradients in sediment concentration cause the observed and the local rate of change of sediment concentration to be significantly different. The novelty of this experiment was that the two gliders were flown in a rigid formation, where one glider trailed the other at a more or less constant distance of 5 km, controlled by an algorithm. This allowed the local rate of change to be quantified - and therefore the net fluxes across the interfaces - by accounting for the effects of horizontal gradients. The validity of this method was assessed by comparing the settling and resuspension/entrainment fluxes with physical drivers: current shear near the pycnocline and bottom shear, with wind effects and tidal motion as proxies, respectively.

Concentrations and Loads of Organic Compounds and Trace Elements in Tributaries to Newark and Raritan Bays, New Jersey

USGS Publications Warehouse

Wilson, Timothy P.; Bonin, Jennifer L.

2007-01-01

A study was undertaken to determine the concentrations and loads of sediment and chemicals delivered to Newark and Raritan Bays by five major tributaries: the Raritan, Passaic, Rahway, Elizabeth, and Hackensack Rivers. This study was initiated by the State of New Jersey as Study I-C of the New Jersey Toxics Reduction Workplan for the New York-New Jersey Harbor, working under the NY-NJ Harbor Estuary Program (HEP) Contaminant Assessment and Reduction Program (CARP). The CARP is a comprehensive effort to evaluate the levels and sources of toxic contaminants to the tributaries and estuarine areas of the NY-NJ Harbor, including Newark and Raritan Bays. The Raritan and Passaic Rivers are large rivers (mean daily discharges of 1,189 and 1,132 cubic feet per second (ft3/s), respectively), that drain large, mixed rural/urban basins. The Elizabeth and Rahway Rivers are small rivers (mean daily discharges of 25.9 and 49.1 ft3/s, respectively) that drain small, highly urbanized and industrialized basins. The Hackensack River drains a small, mixed rural/urban basin, and its flow is highly controlled by an upstream reservoir (mean daily discharge of 90.4 ft3/s). These rivers flow into urbanized estuaries and ultimately, to the Atlantic Ocean. Each of these tributaries were sampled during two to four storm events, and twice each during low-flow discharge conditions. Samples were collected using automated equipment installed at stations adjacent to U.S. Geological Survey streamflow-gaging stations near the heads-of-tide of these rivers. Large-volume (greater than 50 liters of water and a target of 1 gram of sediment), flow-weighted composite samples were collected for chemical analysis using filtration to collect suspended particulates and exchange resin (XAD-2) to sequester dissolved contaminants. Composite whole-water samples were collected for dissolved polycyclic aromatic hydrocarbons (PAH) and for trace element analysis. Additional discrete grab samples were collected throughout each event for trace-element analysis, and multiple samples were collected for suspended sediment (SS), particulate carbon (POC), and dissolved organic carbon (DOC) analysis. The suspended sediment and exchange resin were analyzed for 114 polychlorinated biphenyls (PCBs, by US EPA method 1668A, modified), seven 2,3,7,8-substituted chlorinated dibenzo-p-dioxins (CDD) and 10 dibenzo-p-difurans (CDF) (by US EPA method 1613), 24 PAHs (by low-resolution isotope dilution/mass-spectral methods), 27 organo-chlorine pesticides (OCPs) (by high resolution isotope dilution/mass-spectral methods), and the trace elements mercury (Hg), methyl-mercury (MeHg), lead (Pb), and cadmium (Cd). Isotope dilution methods using gas chromatography and high-and low-resolution mass spectral (GC/MS) detection were used to accurately identify and quantify organic compounds in the sediment and water phases. Trace elements were measured using inductively coupled plasma-mass spectrometry and cold-vapor atomic fluorescence spectrometry methods. The loads of sediment, carbon, and chemicals were calculated for each storm and low-flow event sampled. Because only a few storm events were sampled, yearly loads of sediment were calculated from rating curves developed using historical SS and POC data. The average annual loads of sediment and carbon were calculated for the period 1975-2000, along with the loads for the selected water years being modeled as part of the New York New Jersey Harbor Estuary Program CARP. Comparison of loads calculated using the rating curve method to loads measured during the sampled storm events indicated that the rating curve method likely underpredicts annual loads. Average annual loads of suspended sediment in the tributaries were estimated to be 395,000 kilograms per year (kg/yr) in the Hackensack River, 417,000 kg/yr in the Elizabeth River, 882,000 kg/yr in the Rahway River, 22,700,000 kg/yr in the Passaic River, and 93,100,000 kg/yr in the Raritan River. Averag

Microbial production of organic acids in aquitard sediments and its role in aquifer geochemistry

USGS Publications Warehouse

McMahon, P.B.; Chapelle, F.H.

1991-01-01

MICROBIAL activity in aquifers plays an important part in the chemical evolution of ground water1-5. The most important terminal electron-accepting microbial processes in deeply buried anaerobic aquifers are iron reduction, sulphate reduction and methanogenesis5-8, each of which requires simple organic compounds or hydrogen (H2) as electron donors. Until now, the source of these compounds was unknown because the concentrations of dissolved organic carbon and sedimentary organic carbon in aquifers are extremely low9-11. Here we show that rates of microbial fermentation exceed rates of respiration in organic-rich aquitards (low-permeability sediments stratigraphically adjacent to higher-permeability aquifer sediments), resulting in a net accumulation of simple organic acids in pore waters. In aquifers, however, respiration outpaces fermentation, resulting in a net consumption of organic acids. The concentration gradient that develops in response to these two processes drives a net diffusive flux of organic acids from aquitards to aquifers. Diffusion calculations demonstrate that rates of organic acid transport are sufficient to account for observed rates of microbial respiration in aquifers. This overall process effectively links the large pool of sedimentary organic carbon in aquitards to microbial respiration in aquifers, and is a principal mechanism driving groundwater chemistry changes in aquifers.

Function of minerals in the natural radioactivity level of Vaigai River sediments, Tamilnadu, India--spectroscopical approach.

PubMed

Ramasamy, V; Paramasivam, K; Suresh, G; Jose, M T

2014-01-03

Using Gamma ray and Fourier Transform Infrared (FTIR) spectroscopic techniques, level of natural radioactivity ((238)U, (232)Th and (40)K) and mineralogical characterization of Vaigai River sediments have been analyzed with the view of evaluating the radiation risk and its relation to available minerals. Different radiological parameters are calculated to know the entire radiological characterization. The average of activity concentrations and all radiological parameters are lower than the recommended safety limit. However, some sites are having higher radioactivity values than the safety limit. From the FTIR spectroscopic technique, the minerals such as quartz, microcline feldspar, orthoclase feldspar, kaolinite, gibbsite, calcite, montmorillonite and organic carbon are identified and they are characterized. The extinction co-efficient values are calculated to know the relative distribution of major minerals such as quartz, microcline feldspar, orthoclase feldspar and kaolinite. The calculated values indicate that the amount of quartz is higher than orthoclase feldspar, microcline feldspar and much higher than kaolinite. Crystallinity index is calculated to know the crystalline nature of quartz and the result indicates that the presence of ordered crystalline quartz in the present sediment. The role of minerals in the level of radioactivity is assessed by multivariate statistical analysis (Pearson's correlation and Cluster analysis). The statistical analysis confirms that the clay mineral kaolinite is the major factor than other major minerals to induce the important radioactivity variables such as absorbed dose rate and concentrations of (232)Th and (238)U. Copyright © 2013 Elsevier B.V. All rights reserved.

Sediment accumulation on the Southern California Bight continental margin during the twentieth century

USGS Publications Warehouse

Alexander, C.R.; Lee, H.J.

2009-01-01

Sediment discharged into the portion of the Southern California Bight extending from Santa Barbara to Dana Point enters a complex system of semi-isolated coastal cells, narrow continental shelves, submarine canyons, and offshore basins. On both the Santa Monica and San Pedro margins, 210Pb accumulation rates decrease in an offshore direction (from ??0.5 g cm-2yr-1 to 0.02 g cm-2yr -1), in concert with a fining in sediment grain size (from 4.5?? to 8.5??), suggesting that offshore transport of wave-resuspended material occurs as relatively dilute nepheloid layers and that hemiplegic sedimentation dominates the supply of sediment to the outer shelf, slope, and basins. Together, these areas are effectively sequestering up to 100% of the annual fluvial input. In contrast to the Santa Monica margin, which does not display evidence of mass wasting as an important process of sediment delivery and redistribution, the San Pedro margin does provide numerous examples of failures and mass wasting, suggesting that intraslope sediment redistribution may play a more important role there. Basin deposits in both areas exhibit evidence of turbidites tentatively associated with both major floods and earthquakes, sourced from either the Redondo Canyon (San Pedro Basin) or Dume Canyon (Santa Monica Basin). On the Palos Verdes shelf, sediment-accumulation rates decrease along and across the shelf away from the White's Point outfall, which has been a major source of contaminants to the shelf deposits. Accumulation rates prior to the construction of the outfall were ??0.2 g cm-2yr-1 and increased 1.5-3.7 times during peak discharges from the outfall in 1971. The distal rate of accumulation has decreased by ??50%, from 0.63 g cm -2yr-1 during the period 1971-1992 to 0.29 g cm -2yr-1 during the period 1992-2003. The proximal rate of accumulation, however, has only decreased ??10%, from 0.83 g cm -2yr-1 during the period 1971-1992 to 0.73 g cm -2yr-1 during the period 1992-2003. Effluent-affected sediment layers on the Palos Verdes shelf can be identified in seabed profiles of naturally occurring 238U, which is sequestered in reducing sediments. The Santa Clara River shelf, just north and west of the Santa Monica and San Pedro margins, is fine-grained and flood-dominated. Core profiles of excess 210Pb from sites covering the extent of documented major flood deposition exhibit evidence of rapidly deposited sediment up to 25 cm thick. These beds are developing in an active depocenter in water depths of 30-50 m at an average rate of 0.72 g cm-2yr-1. Budget calculations for annual and 50-yr timescale sediment storage on this shelf shows that 20%-30% of the sediment discharge is retained on the shelf, leaving 70%-80% to be redistributed to the outer shelf, slope, Santa Barbara Basin, and Santa Monica Basin. ?? 2009 The Geological Society of America.

Methylmercury production in sediment from agricultural and non-agricultural wetlands in the Yolo Bypass, California, USA

USGS Publications Warehouse

Marvin-DiPasquale, Mark; Windham-Myers, Lisamarie; Agee, Jennifer L.; Kakouros, Evangelos; Kieu, Le H.; Fleck, Jacob A.; Alpers, Charles N.; Stricker, Craig A.

2014-01-01

As part of a larger study of mercury (Hg) biogeochemistry and bioaccumulation in agricultural (rice growing) and non-agricultural wetlands in California's Central Valley, USA, seasonal and spatial controls on methylmercury (MeHg) production were examined in surface sediment. Three types of shallowly-flooded agricultural wetlands (white rice, wild rice, and fallow fields) and two types of managed (non-agricultural) wetlands (permanently and seasonally flooded) were sampled monthly-to-seasonally. Dynamic seasonal changes in readily reducible ‘reactive’ mercury (Hg(II)R), Hg(II)-methylation rate constants (kmeth), and concentrations of electron acceptors (sulfate and ferric iron) and donors (acetate), were all observed in response to field management hydrology, whereas seasonal changes in these parameters were more muted in non-agricultural managed wetlands. Agricultural wetlands exhibited higher sediment MeHg concentrations than did non-agricultural wetlands, particularly during the fall through late-winter (post-harvest) period. Both sulfate- and iron-reducing bacteria have been implicated in MeHg production, and both were demonstrably active in all wetlands studied. Stoichiometric calculations suggest that iron-reducing bacteria dominated carbon flow in agricultural wetlands during the growing season. Sulfate-reducing bacteria were not stimulated by the addition of sulfate-based fertilizer to agricultural wetlands during the growing season, suggesting that labile organic matter, rather than sulfate, limited their activity in these wetlands. Along the continuum of sediment geochemical conditions observed, values of kmeth increased approximately 10,000-fold, whereas Hg(II)R decreased 100-fold. This suggests that, with respect to the often opposing trends of Hg(II)-methylating microbial activity and Hg(II) availability for methylation, microbial activity dominated the Hg(II)-methylation process, and that along this biogeochemical continuum, conditions that favored microbial sulfate reduction resulted in the highest calculated MeHg production potential rates. Rice straw management options aimed at limiting labile carbon supplies to surface sediment during the post-harvest fall–winter period may be effective in limiting MeHg production within agricultural wetlands.

Methylmercury production in sediment from agricultural and non-agricultural wetlands in the Yolo Bypass, California, USA.

PubMed

Marvin-DiPasquale, Mark; Windham-Myers, Lisamarie; Agee, Jennifer L; Kakouros, Evangelos; Kieu, Le H; Fleck, Jacob A; Alpers, Charles N; Stricker, Craig A

2014-06-15

As part of a larger study of mercury (Hg) biogeochemistry and bioaccumulation in agricultural (rice growing) and non-agricultural wetlands in California's Central Valley, USA, seasonal and spatial controls on methylmercury (MeHg) production were examined in surface sediment. Three types of shallowly-flooded agricultural wetlands (white rice, wild rice, and fallow fields) and two types of managed (non-agricultural) wetlands (permanently and seasonally flooded) were sampled monthly-to-seasonally. Dynamic seasonal changes in readily reducible 'reactive' mercury (Hg(II)R), Hg(II)-methylation rate constants (kmeth), and concentrations of electron acceptors (sulfate and ferric iron) and donors (acetate), were all observed in response to field management hydrology, whereas seasonal changes in these parameters were more muted in non-agricultural managed wetlands. Agricultural wetlands exhibited higher sediment MeHg concentrations than did non-agricultural wetlands, particularly during the fall through late-winter (post-harvest) period. Both sulfate- and iron-reducing bacteria have been implicated in MeHg production, and both were demonstrably active in all wetlands studied. Stoichiometric calculations suggest that iron-reducing bacteria dominated carbon flow in agricultural wetlands during the growing season. Sulfate-reducing bacteria were not stimulated by the addition of sulfate-based fertilizer to agricultural wetlands during the growing season, suggesting that labile organic matter, rather than sulfate, limited their activity in these wetlands. Along the continuum of sediment geochemical conditions observed, values of kmeth increased approximately 10,000-fold, whereas Hg(II)R decreased 100-fold. This suggests that, with respect to the often opposing trends of Hg(II)-methylating microbial activity and Hg(II) availability for methylation, microbial activity dominated the Hg(II)-methylation process, and that along this biogeochemical continuum, conditions that favored microbial sulfate reduction resulted in the highest calculated MeHg production potential rates. Rice straw management options aimed at limiting labile carbon supplies to surface sediment during the post-harvest fall-winter period may be effective in limiting MeHg production within agricultural wetlands. © 2013.

Sedimentary organic matter sources, benthic consumption and burial in west Spitsbergen fjords - Signs of maturing of Arctic fjordic systems?

NASA Astrophysics Data System (ADS)

Zaborska, Agata; Włodarska-Kowalczuk, Maria; Legeżyńska, Joanna; Jankowska, Emilia; Winogradow, Aleksandra; Deja, Kajetan

2018-04-01

Mature ecosystems sequester little organic carbon (Corg) in sediments, as the complex and effective food webs consume most available organic matter within the water column and sediment, in contrast to young systems, where a large proportion of Corg is buried in deeper sediment layers. In this paper we hypothesize that "warmer" Atlantic water influenced fjord exhibits the 'mature' system features as compared to "cooler" Arctic water influenced fjord. Corg concentrations, sources and burial rates, as well as macrobenthic community standing stocks, taxonomic and functional composition and carbon demand, were compared in two west Spitsbergen fjords that are to different extents influenced by Atlantic water and can be treated as representing a cold one (Hornsund) and a warm one (Kongsfjorden). Water, sediments and macrofauna were collected at three stations in the central basin of each fjord. Corg, Ntot, δ13Corg and δ15N were measured in suspended matter, sediment cores and possible organic matter sources. The composition of sources of sedimentary organic matter was modeled by Mix-SIAR Bayesian stable isotope mixing models. The 210Pb method was used to calculate sediment accumulation rates, Corg accumulation and burial rates. The sedimentary Corg concentration and accumulation rate were larger in Hornsund than in Kongsfjorden. The contributions of pelagic sources to the Corg in sediments were similar in both fjords, macroalgal detritus had a higher importance in Kongsfjorden, while terrestrial sources were more important in Hornsund. Similar density and species richness were noted in both fjords, but higher biomass, individual biomass, production and carbon demand of benthic communities were noted in Kongsfjorden despite the lower amounts of Corg in sediments, indicating that macrobenthos responds to quality rather than quantity of available food. Subsurface tube-building conveyer belt detritus feeders (maldanids and oweniids) were responsible for higher standing stocks and carbon consumption in Kongsfjorden. As a result of the lower Corg pool and higher benthic mineralization, the burial rates in Kongsfjorden were much lower (15 g of Corg m- 2 yr- 1) than in Hornsund (38 g of Corg m- 2 yr- 1). Our study indicates that warming of the high latitude fjordic environments may reshape the relative proportions of organic carbon sources and induce maturing of the sea bottom systems, in terms of development of stable, biologically accommodated benthic communities which more efficiently mineralize organic matter and consequently lower sequestration of organic matter in deeper sediments.

The importance of temporal inequality in quantifying vegetated filter strip removal efficiencies

NASA Astrophysics Data System (ADS)

Gall, H. E.; Schultz, D.; Mejia, A.; Harman, C. J.; Raj, C.; Goslee, S.; Veith, T.; Patterson, P. H.

2017-12-01

Vegetated filter strips (VFSs) are best management practices (BMPs) commonly implemented adjacent to row-cropped fields to trap overland transport of sediment and other constituents often present in agricultural runoff. VFSs are generally reported to have high sediment removal efficiencies (i.e., 70 - 95%); however, these values are typically calculated as an average of removal efficiencies observed or simulated for individual events. We argue that due to: (i) positively correlated sediment concentration-discharge relationships; (ii) strong temporal inequality exhibited by sediment transport; and (iii) decreasing VFS performance with increasing flow rates, VFS removal efficiencies over annual time scales may be significantly lower than the per-event values or averages typically reported in the literature and used in decision-making models. By applying a stochastic approach to a two-component VFS model, we investigated the extent of the disparity between two calculation methods: averaging efficiencies from each event over the course of one year, versus reporting the total annual load reduction. We examined the effects of soil texture, concentration-discharge relationship, and VFS slope to reveal the potential errors that may be incurred by ignoring the effects of temporal inequality in quantifying VFS performance. Simulation results suggest that errors can be as low as < 2% and as high as > 20%, with the differences between the two methods of removal efficiency calculations greatest for: (i) soils with high percentage of fine particulates; (ii) VFSs with higher slopes; and (iii) strongly positive concentration-discharge relationships. These results can aid in annual-scale decision making for achieving downstream water quality goals.

Increased terrestrial to ocean sediment and carbon fluxes in the northern Chesapeake Bay associated with twentieth century land alteration

USGS Publications Warehouse

Saenger, C.; Cronin, T. M.; Willard, D.; Halka, J.; Kerhin, R.

2008-01-01

We calculated Chesapeake Bay (CB) sediment and carbon fluxes before and after major anthropogenic land clearance using robust monitoring, modeling and sedimentary data. Four distinct fluxes in the estuarine system were considered including (1) the flux of eroded material from the watershed to streams, (2) the flux of suspended sediment at river fall lines, (3) the burial flux in tributary sediments, and (4) the burial flux in main CB sediments. The sedimentary maximum in Ambrosia (ragweed) pollen marked peak land clearance (~1900 a.d.). Rivers feeding CB had a total organic carbon (TOC)/total suspended solids of 0.24??0.12, and we used this observation to calculate TOC fluxes from sediment fluxes. Sediment and carbon fluxes increased by 138-269% across all four regions after land clearance. Our results demonstrate that sediment delivery to CB is subject to significant lags and that excess post-land clearance sediment loads have not reached the ocean. Post-land clearance increases in erosional flux from watersheds, and burial in estuaries are important processes that must be considered to calculate accurate global sediment and carbon budgets. ?? 2008 Coastal and Estuarine Research Federation.

Toxic metals in Venics lagoon sediments: Model, observation, an possible removal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Basu, A.; Molinaroli, E.

1994-11-01

We have modeled the distribution of nine toxic metals in the surface sediments from 163 stations in the Venice lagoon using published data. Three entrances from the Adriatic Sea control the circulation in the lagoon and divide it into three basins. We assume, for purposes of modeling, that Porto Marghera at the head of the Industrial Zone area is the single source of toxic metals in the Venice lagoon. In a standing body of lagoon water, concentration of pollutants at distance x from the source (C{sub 0}) may be given by C=C{sub 0}e{sup -kx} where k is the rate constantmore » of dispersal. We calculated k empirically using concentrations at the source, and those farthest from it, that is the end points of the lagoon. Average k values (ppm/km) in the lagoon are: Zn 0.165, Cd 0.116, Hg 0.110, Cu 0.105, Co 0.072, Pb 0.058, Ni 0.008, Cr (0.011) and Fe (0.018 percent/km), and they have complex distributions. Given the k values, concentration at source (C{sub 0}), and the distance x of any point in the lagoon from the source, we have calculated the model concentrations of the nine metals at each sampling station. Tides, currents, floor morphology, additional sources, and continued dumping perturb model distributions causing anomalies (observed minus model concentrations). Positive anomalies are found near the source, where continued dumping perturbs initial boundary conditions, and in areas of sluggish circulation. Negative anomalies are found in areas with strong currents that may flush sediments out of the lagoon. We have thus identified areas in the lagoon where higher rate of sediment removal and exchange may lesson pollution. 41 refs., 4 figs., 3 tabs.« less

Sedimentation Coefficient, Frictional Coefficient, and Molecular Weight: A Preparative Ultracentrifuge Experiment for the Advanced Undergraduate Laboratory.

ERIC Educational Resources Information Center

Halsall, H. B.; Wermeling, J. R.

1982-01-01

Describes an experiment using a high-speed preparative centrifuge and calculator to demonstrate effects of the frictional coefficient of a macromolecule on its rate of transport in a force field and to estimate molecular weight of the macromolecule using an empirical relationship. Background information, procedures, and discussion of results are…

30 CFR 250.527 - What must I include in my casing pressure request?

Code of Federal Regulations, 2010 CFR

2010-07-01

... and the calculated daily production rate during last well test (oil, gas, basic sediment, and water... (dry tree, hybrid, or subsea); (n) Date of diagnostic test; (o) Well schematic; (p) Water depth; (q...: (1) Bleed down/buildup test; (2) Shut-in the well and monitor the pressure drop test; (3) Constant...

Monitoring urban impacts on suspended sediment, trace element, and nutrient fluxes within the City of Atlanta, Georgia, USA: Program design, methodological considerations, and initial results

USGS Publications Warehouse

Horowitz, A.J.; Elrick, K.A.; Smith, J.J.

2008-01-01

Atlanta, Georgia (City of Atlanta, COA), is one of the most rapidly growing urban areas in the US. Beginning in 2003, the US Geological Survey established a long-term water-quantity/quality monitoring network for the COA. The results obtained during the first 2 years have provided insights into the requirements needed to determine the extent of urban impacts on water quality, especially in terms of estimating the annual fluxes of suspended sediment, trace/major elements, and nutrients. During 2004/2005, suspended sediment fluxes from the City of Atlanta (COA) amounted to about 150 000 t year-1; ??? 94% of the transport occurred in conjunction with storm-flow, which also accounted for ??? 65% of the annual discharge. Typically, storm-flow averaged ??? 20% of theyear. Normally, annual suspended sediment fluxes are determined by summing daily loads based on a single calculation step using mean-daily discharge and a single rating curve-derived suspended sediment concentration. Due to the small and 'flashy' nature of the COAs streams, this approach could produce underestimates ranging from 25% to 64%. Accurate estimates (?? 15%) require calculation time-steps as short as every 2-3 h. Based on annual median base-flow/storm-flow chemical concentrations, the annual fluxes of ??? 75% of trace elements (e.g. Cu, Pb, Zn), major elements (e.g. Fe, Al), and total P occur in association with suspended sediment; in turn, ??? 90% of the transport of these constituents occur in conjunction with storm-flow. As such, base-flow sediment-associated and dissolved contributions represent relatively insignificant portions of the total annual load. An exception is total N, whose sediment-associated fluxes range from 50% to 60%; even so, storm-related transport typically exceeds 80%. Hence, in urban environments, non-point-source appear to be the dominant contributors to the fluxes of these constituents.

Relationship of sediment discharge to streamflow

USGS Publications Warehouse

Colby, B.R.

1956-01-01

The relationship between rate of sediment discharge and rate of water discharge at a cross section of a stream is frequently expressed by an average curve. This curve is the sediment rating curve. It has been widely used in the computation of average sediment discharge from water discharge for periods when sediment samples were not collected. This report discusses primarily the applications of sediment rating curves for periods during which at least occasional sediment samples were collected. Because sediment rating curves are of many kinds, the selection of the correct kind for each use is important. Each curve should be carefully prepared. In particular, the correct dependent variable must be used or the slope of the sediment rating curve may be incorrect for computing sediment discharges. Sediment rating curves and their applications were studied for the following gaging stations: 1. Niobrara River near Cody, Nebr. 2. Colorado River near Grand Canyon, Ariz. 3. Rio Grande at San Martial, N. Mex. 4. Rio Puerto near Bernardo, N. Mex. 5. White River near Kadoka, S. Dak. 6. Sandusky River near Fremont, Ohio Except for the Sandusky River and the Rio Puerco, which transport mostly fine sediment, one instantaneous sediment rating curve was prepared for the discharge of suspended sands, at each station, and another for the discharge of sediment finer than 0.082 millimeter. Each curve was studied separately, and by trial-end-error multiple correlation some of the factors that cause scatter from the sediment rating curves were determined. Average velocity at the cross section, Water temperature, and erratic fluctuations in concentration seemed to be the three major factors that caused departures from the sediment rating curves for suspended sands. The concentration of suspended sands varied with about the 2.8 power of the mean velocity for the four sediment, rating curves for suspended sands. The effect of water temperature was not so consistent as that of velocity and theoretically should vary considerably with differences in the size composition of the suspended sands. Scatter from the sediment rating curves for sediments finer than 0.082 millimeter seemed to be caused by changes in supply of these sediments. Some of the scatter could be explained by seasonal variations, by a pattern of change in concentration of fine sediment following a rise, or by source of the runoff as indicated by the measured relative flows of certain tributaries. Daily or instantaneous sediment rating curves adjusted for factors that account for some of the scatter from an average curve often can be used to compute approximate daily, monthly, and annual sediment discharges. Accuracy of the computed sediment discharges should be better than average for streams that transport mostly sands rather than fine sediments and for some ephemeral or intermittent streams, such as Rio Puerco, in semiarid regions. Accuracy of computed sediment discharges can be much improved for many streams by shifting the sediment rating curve on the basis of 2 or 4 measurements of sediment discharge per month. Of 26 annual sediment discharges that were computed by shifting sediment rating curves to either 2 or 4 measured sediment discharges per month, 18 were within I0 percent of the annual-sediment discharges that were computed on the basis of a daily sampling program. Monthly and daily sediment discharges computed from daily or instantaneous sediment rating curves, either shifted or unshifted, were less accurate than similarly computed annual sediment discharges. Even so, the difference in cost between occasional sediment samples and daily samples is so great that the added accuracy from daily sampling may not Justify the added cost. Monthly and annual sediment-rating curves can be applied simply, with adjustments if required, to compute monthly and annual sediment discharges with reasonably good accuracy for gaging stations like the Rio Puerco near Bernardo,

The long-term nutrient accumulation with respect to anthropogenic impacts in the sediments from two freshwater marshes (Xianghai Wetlands, Northeast China).

PubMed

Wang, Guo-Ping; Liu, Jing-Shuang; Tang, Jie

2004-12-01

Sediment cores, representing a range of watershed characteristics and anthropogenic impacts, were collected from two freshwater marshes at the Xianghai wetlands (Ramsar site no. 548) in order to trace the historical variation of nutrient accumulation. Cores were (210)Pb- and (137)Cs-dated, and these data were used to calculate sedimentation rates and sediment accumulation rates. Ranges of dry mass accumulation rates and sedimentation rates were 0.27-0.96 g m(-2)yr(-1) and 0.27-0.90 cm yr(-1), respectively. The effect of human activities on increased sediment accumulation rates was observed. Nutrients (TOC, N, P, and S) in sediment were analyzed and nutrient concentration and accumulation were compared in two marshes with different hydrologic regime: an "open" marsh (E-0) and a partly "closed" marsh (F-0). Differences in physical and chemical characteristics between sediments of "open" and partly "closed" marsh were also observed. The "open" marsh sequestered much higher amounts of TOC (1.82%), N (981.1 mg kg(-1)), P (212.17 mg kg(-1)), and S (759.32 mg kg(-1)) than partly "closed" marsh (TOC: 0.32%, N: 415.35 mg kg(-1), P: 139.64 mg kg(-1), and S: 624.45 mg kg(-1)), and the "open" marsh indicated a rather large historical variability of TOC, N, P, and S inputs from alluvial deposits. Nutrient inputs (2.16-251.80 g TOC m(-2) yr(-1), 0.43-20.12 g N m(-2) yr(-1), 0.39-3.03 g P m(-2) yr(-1), 1.60-15.13 g S m(-2) yr(-1)) into the Xianghai wetlands of China are in the high range compared with reported nutrient accumulation rates for freshwater marshes in USA. The vertical variation, particularly for N, P, and S indicated the input history of the nutrients of the Xianghai wetlands developed in three periods--before 1950s, 1950-1980s, and after 1980s. The ratios between anthropogenic and natural inputs showed that the relative anthropogenic inputs of TOC, N, P, and S have been severalfold (TOC: 1.68-11.21, N: 0.47-3.67, P: 0.24-1.36, and S: 1.46-2.96) greater than values of their natural inputs after 1980s. The result is probably attributable, in part, to two decades of surface coal mining activities, urban sewage, and agriculture runoff within the upstream region of the Huolin River. Our findings suggest that the degree of anthropogenic disturbance within the surrounding watershed regulates wetland sediment, TOC, N, P, and S accumulation.

Exploring the performance of the SEDD model to predict sediment yield in eucalyptus plantations. Long-term results from an experimental catchment in Southern Italy

NASA Astrophysics Data System (ADS)

Porto, P.; Cogliandro, V.; Callegari, G.

2018-01-01

In this paper, long-term sediment yield data, collected in a small (1.38 ha) Calabrian catchment (W2), reafforested with eucalyptus trees (Eucalyptus occidentalis Engl.) are used to validate the performance of the SEdiment Delivery Distributed Model (SEDD) in areas with high erosion rates. At first step, the SEDD model was calibrated using field data collected in previous field campaigns undertaken during the period 1978-1994. This first phase allowed the model calibration parameter β to be calculated using direct measurements of rainfall, runoff, and sediment output. The model was then validated in its calibrated form for an independent period (2006-2016) for which new measurements of rainfall, runoff and sediment output are also available. The analysis, carried out at event and annual scale showed good agreement between measured and predicted values of sediment yield and suggested that the SEDD model can be seen as an appropriate means of evaluating erosion risk associated with manmade plantations in marginal areas. Further work is however required to test the performance of the SEDD model as a prediction tool in different geomorphic contexts.

Heat flow and brine generation following the Chesapeake Bay bolide impact

USGS Publications Warehouse

Sanford, W.

2003-01-01

Calculations indicate that the impact of an asteroid or comet on the Atlantic Coastal Plain 35 million years ago created subsequent hydrothermal activity and conditions suitable for phase separation and the creation of the brine observed in the groundwater at the site today. A calculation of groundwater velocity using Darcy's law suggests flow rates are insufficient to have moved the water out of the crater within 35 million years. A similar calculation using Pick's law demonstrates that solutes cannot have escaped by molecular diffusion since the impact. Simulations from other investigators using shock-physics codes indicate that the crust would have been vaporized or melted down to at least 2 km at the time of impact. Based on these calculations, a simulation of heat conduction was made assuming a 1000 ??C initial crustal temperature. The hot crust acted as a heat source, with temperatures peaking in the overlying sediment about 10,000 years later. The pressure and temperature conditions within the sediment during that time would have been favorable for phase separation and generation of a residual brine, which may be found today in the inner crater. ?? 2003 Elsevier Science B.V. All rights reserved.

Evolution and timing of salt diapirism in the Iranian sector of the Persian Gulf

NASA Astrophysics Data System (ADS)

Perotti, Cesare; Chiariotti, Luca; Bresciani, Ilenia; Cattaneo, Luciano; Toscani, Giovanni

2016-06-01

The Iranian sector of the Persian Gulf is affected by more than 30 large diapiric structures triggered by the mobilization of the Infracambrian Hormuz Complex, an evaporite-rich unit that overlies Precambrian basement at the base of the sedimentary succession. Nineteen non-piercing diapirs, without any appreciable salt intrusion into the upper succession, were studied in detail and retro-deformed by the decompaction and unfolding of 13 seismic horizons that were identified by the interpretation of a dense grid of 2D seismic lines and calibrated by well data. Salt uplift had begun by the Early Palaeozoic and persists to the present day, with major pulses of intensity during the Middle Triassic, Cenomanian, Late Oligocene, and post-Middle Miocene. The structural reconstructions and the analysis of the progressive deformation of the study diapirs do not show any link between diapiric uplift and local tectonic structures, and no clear correlation with the regional geodynamic events acting at the boundary of the Arabian plate. On the contrary, the salt uplift seems strongly influenced by the differential rate of sedimentation that affected the whole study basin (more than 40,000 km2), with a coefficient of correlation between the salt uplift rate and the differential rate of sedimentation (expressed by the standard deviation of the sedimentation rate calculated over the entire basin) of 0.95. This downbuilding mechanism of diapiric growth is apparently induced by differential sedimentation over long distances (several tens of kilometers), showing that the flow of salt affected the whole basin and not just the areas around the single diapiric structures.

A Tidally Averaged Sediment-Transport Model for San Francisco Bay, California

USGS Publications Warehouse

Lionberger, Megan A.; Schoellhamer, David H.

2009-01-01

A tidally averaged sediment-transport model of San Francisco Bay was incorporated into a tidally averaged salinity box model previously developed and calibrated using salinity, a conservative tracer (Uncles and Peterson, 1995; Knowles, 1996). The Bay is represented in the model by 50 segments composed of two layers: one representing the channel (>5-meter depth) and the other the shallows (0- to 5-meter depth). Calculations are made using a daily time step and simulations can be made on the decadal time scale. The sediment-transport model includes an erosion-deposition algorithm, a bed-sediment algorithm, and sediment boundary conditions. Erosion and deposition of bed sediments are calculated explicitly, and suspended sediment is transported by implicitly solving the advection-dispersion equation. The bed-sediment model simulates the increase in bed strength with depth, owing to consolidation of fine sediments that make up San Francisco Bay mud. The model is calibrated to either net sedimentation calculated from bathymetric-change data or measured suspended-sediment concentration. Specified boundary conditions are the tributary fluxes of suspended sediment and suspended-sediment concentration in the Pacific Ocean. Results of model calibration and validation show that the model simulates the trends in suspended-sediment concentration associated with tidal fluctuations, residual velocity, and wind stress well, although the spring neap tidal suspended-sediment concentration variability was consistently underestimated. Model validation also showed poor simulation of seasonal sediment pulses from the Sacramento-San Joaquin River Delta at Point San Pablo because the pulses enter the Bay over only a few days and the fate of the pulses is determined by intra-tidal deposition and resuspension that are not included in this tidally averaged model. The model was calibrated to net-basin sedimentation to calculate budgets of sediment and sediment-associated contaminants. While simulated net sedimentation in the four basins that comprise San Francisco Bay was correct, the simulations incorrectly eroded shallows while channels deposited because model surface-layer boxes span both shallows and channels, and neglect lateral variability of suspended-sediment concentration. Validation with recent (1983-2005) net sedimentation in South San Francisco Bay was poor, perhaps owing to poorly quantified sediment supply, and to invasive species that altered erosion and deposition processes. This demonstrates that deterministically predicting future sedimentation is difficult in this or any estuary for which boundary conditions are not stationary. The model would best be used as a tool for developing past and present sediment budgets, and for creating scenarios of future sedimentation that are compared to one another rather than considered a deterministic prediction.

Advanced Water Quality Modelling in Marine Systems: Application to the Wadden Sea, the Netherlands

NASA Astrophysics Data System (ADS)

Boon, J.; Smits, J. G.

2006-12-01

There is an increasing demand for knowledge and models that arise from water management in relation to water quality, sediment quality (ecology) and sediment accumulation (ecomorphology). Recently, models for sediment diagenesis and erosion developed or incorporated by Delft Hydraulics integrates the relevant physical, (bio)chemical and biological processes for the sediment-water exchange of substances. The aim of the diagenesis models is the prediction of both sediment quality and the return fluxes of substances such as nutrients and micropollutants to the overlying water. The resulting so-called DELWAQ-G model is a new, generic version of the water and sediment quality model of the DELFT3D framework. One set of generic water quality process formulations is used to calculate process rates in both water and sediment compartments. DELWAQ-G involves the explicit simulation of sediment layers in the water quality model with state-of-the-art process kinetics. The local conditions in a water layer or sediment layer such as the dissolved oxygen concentration determine if and how individual processes come to expression. New processes were added for sulphate, sulphide, methane and the distribution of the electron-acceptor demand over dissolved oxygen, nitrate, sulphate and carbon dioxide. DELWAQ-G also includes the dispersive and advective transport processes in the sediment and across the sediment-water interface. DELWAQ-G has been applied for the Wadden Sea. A very dynamic tidal and ecologically active estuary with a complex hydrodynamic behaviour located at the north of the Netherlands. The predicted profiles in the sediment reflect the typical interactions of diagenesis processes.

Role of land use change in landslide-related sediment fluxes in tropical mountain regions

NASA Astrophysics Data System (ADS)

Guns, M.; Vanacker, V.; Demoulin, A.

2012-04-01

Tropical mountain regions are characterised by high denudation rates. Landslides are known to be recurrent phenomena in active mountain belts, but their contribution to the overall sedimentary fluxes is not yet well known. Previous studies on sedimentary cascades have mostly focused on natural environments, without considering the impact of human and/or anthropogenic disturbances on sedimentary budgets. In our work, we hypothesise that human-induced land use change might alter the sediment cascade through shifts in the landslide magnitude-frequency relationship. We have tested this assumption in the Virgen Yacu catchment (approximately 11km2), in the Ecuadorian Cordillera Occidental. Landslide inventories and land use maps were established based on a series of sequential aerial photos (1963, 1977, 1984 and 1989), a HR Landsat image (2001) and a VHR WorldView2 image (2010). Aerial photographs were ortho-rectified, and coregistred with the WorldView2 satellite image. Field campaigns were realised in 2010 and 2011 to collect field-based data on landslide type and geometry (depth, width and length). This allowed us to establish an empirical relationship between landslide area and volume, which was then applied to the landslide inventories to estimate landslide-related sediment production rates for various time periods. The contribution of landslides to the overall sediment flux of the catchment was estimated by comparing the landslide-related sediment production to the total sediment yield. The empirical landslide area-volume relationship established here for the Ecuadorian Andes is similar to that derived for the Himalayas. It suggests that landslides are the main source of sediment in this mountainous catchment. First calculations indicate that human-induced land use change alters the magnitude-frequency relationship through strong increase of small landslides.

Use of the [(14)C]leucine incorporation technique to measure bacterial production in river sediments and the epiphyton.

PubMed

Fischer, H; Pusch, M

1999-10-01

Bacterial production is a key parameter for the understanding of carbon cycling in aquatic ecosystems, yet it remains difficult to measure in many aquatic habitats. We therefore tested the applicability of the [(14)C]leucine incorporation technique for the measurement of bulk bacterial production in various habitats of a lowland river ecosystem. To evaluate the method, we determined (i) extraction efficiencies of bacterial protein from the sediments, (ii) substrate saturation of leucine in sediments, the biofilms on aquatic plants (epiphyton), and the pelagic zone, (iii) bacterial activities at different leucine concentrations, (iv) specificity of leucine uptake by bacteria, and (v) the effect of the incubation technique (perfused-core incubation versus slurry incubation) on leucine incorporation into protein. Bacterial protein was best extracted from sediments and precipitated by hot trichloroacetic acid treatment following ultrasonication. For epiphyton, an alkaline-extraction procedure was most efficient. Leucine incorporation saturation occurred at 1 microM in epiphyton and 100 nM in the pelagic zone. Saturation curves in sediments were difficult to model but showed the first level of leucine saturation at 50 microM. Increased uptake at higher leucine concentrations could be partly attributed to eukaryotes. Addition of micromolar concentrations of leucine did not enhance bacterial electron transport activity or DNA replication activity. Similar rates of leucine incorporation into protein calculated for whole sediment cores were observed after slurry and perfused-core incubations, but the rates exhibited strong vertical gradients after the core incubation. We conclude that the leucine incorporation method can measure bacterial production in a wide range of aquatic habitats, including fluvial sediments, if substrate saturation and isotope dilution are determined.

Use of the [14C]Leucine Incorporation Technique To Measure Bacterial Production in River Sediments and the Epiphyton

PubMed Central

Fischer, Helmut; Pusch, Martin

1999-01-01

Bacterial production is a key parameter for the understanding of carbon cycling in aquatic ecosystems, yet it remains difficult to measure in many aquatic habitats. We therefore tested the applicability of the [14C]leucine incorporation technique for the measurement of bulk bacterial production in various habitats of a lowland river ecosystem. To evaluate the method, we determined (i) extraction efficiencies of bacterial protein from the sediments, (ii) substrate saturation of leucine in sediments, the biofilms on aquatic plants (epiphyton), and the pelagic zone, (iii) bacterial activities at different leucine concentrations, (iv) specificity of leucine uptake by bacteria, and (v) the effect of the incubation technique (perfused-core incubation versus slurry incubation) on leucine incorporation into protein. Bacterial protein was best extracted from sediments and precipitated by hot trichloroacetic acid treatment following ultrasonication. For epiphyton, an alkaline-extraction procedure was most efficient. Leucine incorporation saturation occurred at 1 μM in epiphyton and 100 nM in the pelagic zone. Saturation curves in sediments were difficult to model but showed the first level of leucine saturation at 50 μM. Increased uptake at higher leucine concentrations could be partly attributed to eukaryotes. Addition of micromolar concentrations of leucine did not enhance bacterial electron transport activity or DNA replication activity. Similar rates of leucine incorporation into protein calculated for whole sediment cores were observed after slurry and perfused-core incubations, but the rates exhibited strong vertical gradients after the core incubation. We conclude that the leucine incorporation method can measure bacterial production in a wide range of aquatic habitats, including fluvial sediments, if substrate saturation and isotope dilution are determined. PMID:10508068

Diagenetic changes of lignin compounds in a more than 0.6 million-year-old lacustrine sediment (Lake Biwa, Japan)

NASA Astrophysics Data System (ADS)

Ishiwatari, Ryoshi; Uzaki, Minoru

1987-02-01

A vertical profile of lignin in the upper 700 m layer of a 1400 m sediment core of Lake Biwa, an oligotrophic freshwater lake in Japan, was determined using a CuO oxidative degradation method. The results indicated that lignin is found throughout the core, demonstrating lignin to be very stable for over 0.6 million years. Moreover, the upper 250 m (approximately 0.6 million years old) segment of the sediment core was investigated to determine the apparent long term degradation rate of lignin. A downward lignin concentration decrease is observed over the upper 250 m of the core which corresponds to a calculated half life of at least approximately 40 × 10 4 years, assuming that lignin decrease is due to its in situ degradation (diagenesis).

Sediment Flux of Particulate Organic Phosphorus in the Open Black Sea

NASA Astrophysics Data System (ADS)

Parkhomenko, A. V.; Kukushkin, A. S.

2018-03-01

The interannual variation of the monthly average (weighted average) concentrations of particulate organic phosphorus (PPOM) in the photosynthetic layer, oxycline, redox zone, and H2S zone in the open Black Sea is estimated based on long-term observation data. The suspension sedimentation rates from the studied layers are assessed using model calculations and published data. The annual variation of PPOM sediment fluxes from the photosynthetic layer, oxycline, redox zone, and upper H2S zone to the anaerobic zone of the sea and the correspondingly annual average values are estimated for the first time. A regular decrease in the PPOM annual average flux with depth in the upper active layer is demonstrated. A correlation between the annual average values of PPOM sediment flux from the photosynthetic layer and ascending phosphate flux to this layer is shown, which suggests their balance in the open sea. The results are discussed in terms of the phosphorus biogeochemical cycle and the concept of new and regenerative primary production in the open Black Sea.

Methods for the Calculation of Settling Tanks for Batch Experiments; METODOS DE CALCULO DE ESPESADORES POR ENSAYOS DISCONTINUOS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasos, P.; Perea, C.P.; Jodra, L.G.

1957-01-01

>In order to calculate settling tanks, some tests on batch sedimentation were made, and with the data obtained the dimensions of the settling tank were found. The mechanism of sedimentation is first briefly described, and then the factors involved in the calculation of the dimensions and the sedimentation velocity are discussed. The Cloe and Clevenger method and the Kynch method were investigated experimentally and compared. The application of the calculations are illustrated. It is shown that the two methods gave markedly different results. (J.S.R.)

Suspended-Sediment Export From Four Small Montane Humid-Tropical Watersheds With Varying Land use and Lithology, Puerto Rico

NASA Astrophysics Data System (ADS)

Larsen, M. C.

2003-12-01

Intensive land-use conversion of forested landscapes to agricultural use accelerated in most of the global tropics during the 20th century and has resulted in large increases in soil erosion and suspended-sediment export. Fluvial sediment is one of the most abundant freshwater contaminants on earth. Stormflows episodically transport sediment to reservoirs, estuaries and in coastal waters where coral reefs are located. The sediment and associated contaminants such as pesticides, herbicides, and fertilizers, degrade water quality and are harmful to aquatic organisms in these areas. Improved understanding of the processes and rates of fluvial sediment transport in natural and anthropogenically disturbed settings enhances management of natural resources and aids in the establishment of standards for acceptable sediment concentrations. Four USGS WEBB (Water, Energy, and Biogeochemical Budgets) study watersheds in Puerto Rico (18° latitude) were paired to compare and contrast the effects of land use and bedrock geology on suspended-sediment yield. Sediment concentration, calculated as sediment yield normalized to runoff, was more than three times greater in two watersheds in secondary forest and pasture compared to sediment concentration in watersheds in primary forest. The influence of lithology was comparable: sediment concentration in intrusive-bedrock (quartz diorite and granodiorite) watersheds was more than three times higher than sediment concentration in volcaniclastic-bedrock (volcanic sandstone, mudstone, and breccia) watersheds. These contrasts highlight the well-known effect of land use on sediment concentration and yield but also demonstrate the strong control of bedrock geology. Most importantly, the high sediment yields in the watersheds that were converted to pasture and secondary forest, even after 60 years of forest reestablishment, provide a glimpse into the future of tropical watersheds elsewhere that are now undergoing deforestation. Erosion rates observed in agriculturally-developed watersheds are substantial in regard to reservoir storage. Public water supply for the city of San Juan (population 1.6 million) is largely derived from surface-water storage. The principal San Juan reservoir lost approximately 60 percent of its storage capacity from siltation in the 40 years following impoundment in 1954. The reduced storage capacity resulted in severe water rationing for San Juan during several droughts during the past decade.

Short Term Sediment Exchange Between Marshes and Bays Using Beryllium-7 as a Tracer, Fourleague Bay, Louisiana.

NASA Astrophysics Data System (ADS)

Restreppo, G. A.; Bentley, S. J.; Xu, K.; Wang, J.

2016-12-01

Modern delta models focus on the availability and exchange of coarse sediment as one of the major factors of deltaic growth or decay. Fine-grained sediment exchange within a river's delta is relatively poorly understood, as is the impact that this exchange has on land building and land loss. To better understand the dynamics of fine grain sediment exchange between river mouth, adjacent bays, and marshland, sediment cores from Fourleague Bay, LA, were collected and analyzed for 7Be, a naturally occurring radioisotope that serves as a marker for recently deposited sediment. Time-series push cores were collected every two months at ten sites, five located across a longitudinal transect in the middle bay and five located along adjacent marshes, from May 2015 to May 2016. All sites fall within 11 to 28 km of the Atchafalaya Delta, along a gradient extending towards the open ocean. Cores were extruded in 2 cm intervals, dried, ground, and analyzed via gamma spectrometry for the presence of 7Be. Inventories of 7Be were then calculated and used to determine bimonthly sedimentation rates over the course twelve months. Sediment deposition on the bay floor and marsh surface were then compared to Atchafalaya River discharge, wind speed and direction, and wave action. Preliminary results indicate patterns of initial fluvial sediment transfer from river to bay floor, then bay floor to marsh surface, with decreasing fluvial influence towards the open ocean. Sediment transport from bay to marsh appears to be coupled with meteorological forcing that induces bay-floor sediment resuspension and the flooding of marsh surfaces. This indirect mechanism of fluvial sediment supply to wetland surfaces may extend the region of influence for sediment delivery from man-made river-sediment diversions.

Patterns of sediment accumulation in the tidal marshes of Maine

USGS Publications Warehouse

Wood, M.E.; Kelley, J.T.; Belknap, D.F.

1989-01-01

One year's measurements of surficial sedimentation rates (1986-1987) for 26 Maine marsh sites were made over marker horizons of brick dust. Observed sediment accumulation rates, from 0 to 13 mm yr-1, were compared with marsh morphology, local relative sea-level rise rate, mean tidal range, and ice rafting activity. Marshes with four different morphologies (back-barrier, fluvial, bluff-toe, and transitional) showed distinctly different sediment accumulation rates. In general, back-barrier marshes had the highest accumulation rates and blufftoe marshes had the lowest rates, with intermediate values for transitional and fluvial marshes. No causal relationship between modern marsh sediment accumulation rate and relative sea-level rise rate (from tide gauge records) was observed. Marsh accretionary balance (sediment accumulation rate minus relative sea-level rise rate) did not correlate with mean tidal range for this meso- to macro-tidal area. Estimates of ice-rafted debris on marsh sites ranged from 0% to >100% of measured surficial sedimentation rates, indicating that ice transport of sediment may make a significant contribution to surficial sedimentation on Maine salt marshes. ?? 1989 Estuarine Research Federation.

Intercalibration of benthic flux chambers I. Accuracy of flux measurements and influence of chamber hydrodynamics [review article

NASA Astrophysics Data System (ADS)

Tengberg, A.; Stahl, H.; Gust, G.; Müller, V.; Arning, U.; Andersson, H.; Hall, P. O. J.

2004-01-01

The hydrodynamic properties and the capability to measure sediment-water solute fluxes, at assumed steady state conditions, were compared for three radically different benthic chamber designs: the “Microcosm”, the “Mississippi” and the “Göteborg” chambers. The hydrodynamic properties were characterized by mounting a PVC bottom in each chamber and measuring mixing time, diffusive boundary layer thickness (DBL thickness) shear velocity (u ∗) , and total pressure created by the water mixing. The Microcosm had the most even distribution of DBL thickness and u ∗, but the highest differential pressure at high water mixing rates. The Mississippi chamber had low differential pressures at high u ∗. The Göteborg chamber was in between the two others regarding these properties. DBL thickness and u ∗ were found to correlate according to the following empirical formula: DBL=76.18(u ∗) -0.933. Multiple flux incubations with replicates of each of the chamber types were carried out on homogenized, macrofauna-free sediments in four tanks. The degree of homogeneity was determined by calculating solute fluxes (of oxygen, silicate, phosphate and ammonium) from porewater profiles and by sampling for porosity, organic carbon and meiofauna. All these results, except meiofauna, indicated that there were no significant horizontal variations within the sediment in any of the parallel incubation experiments. The statistical evaluations also suggested that the occasional variations in meiofauna abundance did not have any influence on the measured solute fluxes. Forty-three microelectrode profiles of oxygen in the DBL and porewater were evaluated with four different procedures to calculate diffusive fluxes. The procedure presented by Berg, Risgaard-Petersen and Rysgaard, 1989 [Limnol. Oceanogr. 43, 1500] was found to be superior because of its ability to fit measured profiles accurately, and because it takes into consideration vertical zonation with different oxygen consumption rates in the sediment. During the flux incubations, the mixing in the chambers was replicated ranging from slow mixing to just noticeable sediment resuspension. In the “hydrodynamic characterizations” these mixing rates corresponded to average DBL thickness from 120 to 550 μm, to u ∗ from 0.12 to 0.68 cm/s, and to differential pressures from 0-3 Pa. Although not directly transferable, since the incubations were done on a “real” sediment with a rougher surface while in the characterizations a PVC plate simulated the sediments surface, these data give ideas about the prevailing hydrodynamic condition in the chambers during the incubations. The variations in water mixing did not generate statistically significant differences between the chamber types for any of the measured fluxes of oxygen or nutrients. Consequently it can be concluded that, for these non-permeable sediments and so long as appropriate water mixing (within the ranges given above) is maintained, the type of stirring mechanism and chamber design used were not critical for the magnitude of the measured fluxes. The average measured oxygen flux was 11.2 ± 2.7 (from 40 incubations), while the diffusive flux calculated (from 43 profiles using the Berg et al., 1989 [Limnol. Oceanogr. 43, 1500] procedure) was 11.1 ± 3.0 mmol m -2 day -1. This strongly suggests that accurate oxygen flux measurements were obtained with the three types of benthic chambers used and that the oxygen uptake is diffusive.

Continuous and Episodic Modern Sediment Accumulation on Monterey Fan: Evidence from Ddt, 137Cs and Excess 210Pb

NASA Astrophysics Data System (ADS)

Gwiazda, R.; Paull, C. K.; Alexander, C. R.; Ussler, W.

2012-12-01

The mode and magnitude of fine-grained sediment accumulation on the Monterey Fan off the California central coast was investigated using pesticide concentrations and radioactive tracer profiles in sediment cores. DDT is a man-made pesticide that was used extensively in central California between 1945 and 1970. As such, its presence in marine sediments is a telltale sign of a modern sedimentation age. DDT and its metabolites, DDE and DDD, (collectively referred to as DDTr) were measured in fifty-five ~20cm-long sediment cores collected from the surface of the Monterey Fan up to 250 km to the south and 210 km to the west of the Monterey Canyon head, and in four transects across the Monterey Canyon channel at maximum water depths of 3160, 3380, 3580, and 3880 meters. Profiles of excess 210Pb (210Pbxs) and 137Cs were measured in 5 cores from the Fan to estimate recent sedimentation rates. Detectable levels of DDTr were observed in all but one of these cores, with DDTr concentrations characteristically highest at the surface and decreasing with depth. The area-normalized and depth-integrated DDTr content measured in all the cores in the Fan and in the deepest two channel transects was geographically fairly homogenous, with no statistical relationship between DDTr inventory and distance from the main channel crossing the Fan. The total sediment mass deposited on the Fan over the last 60 years, inferred from the total inventory of DDTr present in the area surveyed, is consistent with the amount of sediment delivered by the Salinas River over the same time period. 210Pbxs activities are fairly homogeneous within an uppermost layer of variable thickness (4.6-8cm) and decrease exponentially below it, but these exponential decreases are often interrupted by horizons with constant or increased 210Pbxs activity. Moreover, the coexistence of variable DDTr concentrations with homogeneous 210Pbxs activities in the top sediment indicates that the uniformity of 210Pbxs is not due primarily to bioturbation but rather the result of deposition of thick layers with constant 210Pbxs. These data indicate that fine-grained sedimentation on the Monterrey Fan appears to have a dual modality consisting of sustained slow accumulation at a modest rate during quiescent periods interrupted by episodes of rapid accumulation during discrete events. Median sedimentation rates during quiescent periods are 0.07 cm yr-1, but over the 110 year period of detectable 210Pbxs, which includes both slow continuous sedimentation and rapid accumulation events, the median overall sedimentation rate, calculated from the deepest detectable 210Pbxs samples, is 0.19 cm yr-1. On a per mass basis, sedimentation on the Fan has been equally divided between periods of continual slow accumulation and episodes of fast accumulation. The rapidly deposited layers on the Monterey Fan are inferred to result from the injection of fluvial sediments onto the Fan during episodic and exceptionally large floods of the Salinas River.

Parsing anomalous versus normal diffusive behavior of bedload sediment particles

USGS Publications Warehouse

Fathel, Siobhan; Furbish, David; Schmeeckle, Mark

2016-01-01

Bedload sediment transport is the basic physical ingredient of river evolution. Formulae exist for estimating transport rates, but the diffusive contribution to the sediment flux, and the associated spreading rate of tracer particles, are not clearly understood. The start-and-stop motions of sediment particles transported as bedload on a streambed mimic aspects of the Einstein–Smoluchowski description of the random-walk motions of Brownian particles. Using this touchstone description, recent work suggests the presence of anomalous diffusion, where the particle spreading rate differs from the linear dependence with time of Brownian behavior. We demonstrate that conventional measures of particle spreading reveal different attributes of bedload particle behavior depending on details of the calculation. When we view particle motions over start-and-stop timescales obtained from high-speed (250 Hz) imaging of coarse-sand particles, high-resolution measurements reveal ballistic-like behavior at the shortest (10−2 s) timescale, followed by apparent anomalous behavior due to correlated random walks in transition to normal diffusion (>10−1 s) – similar to Brownian particle behavior but involving distinctly different physics. However, when treated as a ‘virtual plume’ over this timescale range, particles exhibit inhomogeneous diffusive behavior because both the mean and the variance of particle travel distances increase nonlinearly with increasing travel times, a behavior that is unrelated to anomalous diffusion or to Brownian-like behavior. Our results indicate that care is needed in suggesting anomalous behavior when appealing to conventional measures of diffusion formulated for ideal particle systems.

Vertical suspsended sediment fluxes observed from ocean gliders

NASA Astrophysics Data System (ADS)

Merckelbach, Lucas; Carpenter, Jeffrey

2016-04-01

Many studies trying to understand a coastal system in terms of sediment transport paths resort to numerical modelling - combining circulation models with sediment transport models. Two aspects herein are crucial: sediment fluxes across the sea bed-water column interface, and the subsequent vertical mixing by turbulence. Both aspects are highly complex and have relatively short time scales, so that the processes involved are implemented in numerical models as parameterisations. Due to the effort required to obtain field observations of suspended sediment concentrations (and other parameters), measurements are scarce, which makes the development and tuning of parameterisations a difficult task. Ocean gliders (autonomous underwater vehicles propelled by a buoyancy engine) provide a platform complementing more traditional methods of sampling. In this work we present observations of suspended sediment concentration (SSC) and dissipation rate taken by two gliders, each equipped with optical sensors and a microstructure sensor, along with current observations from a bottom mounted ADCP, all operated in the German Bight sector of the North Sea in Summer 2014. For about two weeks of a four-week experiment, the gliders were programmed to fly in a novel way as Lagrangian profilers to water depths of about 40 m. The benefit of this approach is that the rate of change of SSC - and other parameters - is local to the water column, as opposed to an unknown composition of temporal and spatial variability when gliders are operated in the usual way. Therefore, vertical sediment fluxes can be calculated without the need of the - often dubious - assumption that spatial variability can be neglected. During the experiment the water column was initially thermally stratified, with a cross-pycnocline diffusion coefficient estimated at 7\\cdot10-5 m2 s-1. Halfway through the experiment the remnants of tropical storm Bertha arrived at the study site and caused a complete mixing of the water column. An analysis of the data showed that resuspension and deposition were solely tidally-driven and in equilibrium prior to the arrival of the storm, with an averaged resuspension rate of 3-4 g m-2 s-1. During the storm the effect of surface waves increased the resuspension rate by an order of magnitude. The data suggest that after the passing of the storm, when the tide was the main driver again, resuspension rates are generally higher than before the storm. This provides a further indication that although a (Summer) storm might be a short-term event, its effects on sediment transport may be felt on much longer time scales.

Internal loading of phosphorus in a sedimentation pond of a treatment wetland: effect of a phytoplankton crash.

PubMed

Palmer-Felgate, Elizabeth J; Mortimer, Robert J G; Krom, Michael D; Jarvie, Helen P; Williams, Richard J; Spraggs, Rachael E; Stratford, Charlie J

2011-05-01

Sedimentation ponds are widely believed to act as a primary removal process for phosphorus (P) in nutrient treatment wetlands. High frequency in-situ P, ammonium (NH(4)(+)) and dissolved oxygen measurements, alongside occasional water quality measurements, assessed changes in nutrient concentrations and productivity in the sedimentation pond of a treatment wetland between March and June. Diffusive equilibrium in thin films (DET) probes were used to measure in-situ nutrient and chemistry pore-water profiles. Diffusive fluxes across the sediment-water interface were calculated from the pore-water profiles, and dissolved oxygen was used to calculate rates of primary productivity and respiration. The sedimentation pond was a net sink for total P (TP), soluble reactive P (SRP) and NH(4)(+) in March, but became subject to a net internal loading of TP, SRP and NH(4)(+) in May, with SRP concentrations increasing by up to 41μM (1300μl(-1)). Reductions in chlorophyll a and dissolved oxygen concentrations also occurred at this time. The sediment changed from a small net sink of SRP in March (average diffusive flux: -8.2μmolm(-2)day(-1)) to a net source of SRP in June (average diffusive flux: +1324μmolm(-2)day(-1)). A diurnal pattern in water column P concentrations, with maxima in the early hours of the morning, and minima in the afternoon, occurred during May. The diurnal pattern and release of SRP from the sediment were attributed to microbial degradation of diatom biomass, causing reduction of the dissolved oxygen concentration and leading to redox-dependent release of P from the sediment. In June, 2.7mol-Pday(-1) were removed by photosynthesis and 23mol-Pday(-1) were supplied by respiration in the lake volume. SRP was also released through microbial respiration within the water column, including the decomposition of algal matter. It is imperative that consideration to internal recycling is given when maintaining sedimentation ponds, and before the installation of new ponds designed to treat nutrient waste. Copyright © 2011 Elsevier B.V. All rights reserved.

Downslope transport does not explain higher 230Th inventories in the Panama Basin

NASA Astrophysics Data System (ADS)

Singh, A. K.; Marcantonio, F.; Lyle, M. W.

2009-12-01

Mass accumulation rates (burial fluxes) in the Panama Basin calculated using oxygen isotope age models differ from those calculated using the 230Th normalized flux method. During the Holocene and the last glacial, the 230Th-derived MARs are consistently lower than age-model-derived MARs. Most importantly, using both methods, glacial MARs are always significantly higher than Holocene MARs. The discrepancy in the calculated MARs may be due to deep-ocean sediment redistribution processes, specifically downslope transport of sediments from nearby topographic highs [1]. We test this hypothesis by analyzing sediment from shallower sites throughout the Panama basin (from 712-2870 meters) and, specifically, from the tops of ridges surrounding the basin (e.g., Carnegie and Cocos Ridges). Based on 230Th methodology we determine ridge-top focusing factors (FF) that are as high as, or higher than those in the deeper parts of the basin, as determined by us or others [1]. The excess inventories of 230Th are also proportionally higher during the glacial versus Holocene in all but one of the nine new sites we have analyzed. If the source of the higher-than-predicted inventory of 230Th is topographic highs in the region, one would expect to see a correlation between 230Th and depth. We find no such correlation. Although our data suggest that within-basin topographic highs are not the source of higher 230Th inventories in the region, extrabasinal sources cannot be ruled out. In addition, there is the possibility that MARs can be underestimated using the 230Th method in Panama Basin sediments. [1] Kienast et al. 2007, Paleoceanography 22, 2213.

Methods for Measuring Specific Rates of Mercury Methylation and Degradation and Their Use in Determining Factors Controlling Net Rates of Mercury Methylation

PubMed Central

Ramlal, Patricia S.; Rudd, John W. M.; Hecky, Robert E.

1986-01-01

A method was developed to estimate specific rates of demethylation of methyl mercury in aquatic samples by measuring the volatile 14C end products of 14CH3HgI demethylation. This method was used in conjunction with a 203Hg2+ radiochemical method which determines specific rates of mercury methylation. Together, these methods enabled us to examine some factors controlling the net rate of mercury methylation. The methodologies were field tested, using lake sediment samples from a recently flooded reservoir in the Southern Indian Lake system which had developed a mercury contamination problem in fish. Ratios of the specific rates of methylation/demethylation were calculated. The highest ratios of methylation/demethylation were calculated. The highest ratios of methylation/demethylation occurred in the flooded shorelines of Southern Indian Lake. These results provide an explanation for the observed increases in the methyl mercury concentrations in fish after flooding. PMID:16346959

Source, conveyance and fate of suspended sediments following Hurricane Irene. New England, USA

USGS Publications Warehouse

Yellen, Brian; Woodruff, Jon D.; Kratz, Laura N.; Mabee, Steven B.; Morrison, Jonathan; Martini, Anna M.

2014-01-01

Hurricane Irene passed directly over the Connecticut River valley in late August, 2011. Intense precipitation and high antecedent soil moisture resulted in record flooding, mass wasting and fluvial erosion, allowing for observations of how these rare but significant extreme events affect a landscape still responding to Pleistocene glaciation and associated sediment emplacement. Clays and silts from upland glacial deposits, once suspended in the stream network, were routed directly to the mouth of the Connecticut River, resulting in record-breaking sediment loads fifteen-times greater than predicted from the pre-existing rating curve. Denudation was particularly extensive in mountainous areas. We calculate that sediment yield during the event from the Deerfield River, a steep tributary comprising 5% of the entire Connecticut River watershed, exceeded at minimum 10–40 years of routine sediment discharge and accounted for approximately 40% of the total event sediment discharge from the Connecticut River. A series of surface sediment cores taken in floodplain ponds adjacent to the tidal section of the Connecticut River before and after the event provides insight into differences in sediment sourcing and routing for the Irene event compared to periods of more routine flooding. Relative to routine conditions, sedimentation from Irene was anomalously inorganic, fine grained, and enriched in elements commonly found in chemically immature glacial tills and glaciolacustrine material. These unique sedimentary characteristics document the crucial role played by extreme precipitation from tropical disturbances in denuding this landscape.

Source, conveyance and fate of suspended sediments following Hurricane Irene. New England, USA

NASA Astrophysics Data System (ADS)

Yellen, B.; Woodruff, J. D.; Kratz, L. N.; Mabee, S. B.; Morrison, J.; Martini, A. M.

2014-12-01

Hurricane Irene passed directly over the Connecticut River valley in late August, 2011. Intense precipitation and high antecedent soil moisture resulted in record flooding, mass wasting and fluvial erosion, allowing for observations of how these rare but significant extreme events affect a landscape still responding to Pleistocene glaciation and associated sediment emplacement. Clays and silts from upland glacial deposits, once suspended in the stream network, were routed directly to the mouth of the Connecticut River, resulting in record-breaking sediment loads fifteen-times greater than predicted from the pre-existing rating curve. Denudation was particularly extensive in mountainous areas. We calculate that sediment yield during the event from the Deerfield River, a steep tributary comprising 5% of the entire Connecticut River watershed, exceeded at minimum 10-40 years of routine sediment discharge and accounted for approximately 40% of the total event sediment discharge from the Connecticut River. A series of surface sediment cores taken in floodplain ponds adjacent to the tidal section of the Connecticut River before and after the event provides insight into differences in sediment sourcing and routing for the Irene event compared to periods of more routine flooding. Relative to routine conditions, sedimentation from Irene was anomalously inorganic, fine grained, and enriched in elements commonly found in chemically immature glacial tills and glaciolacustrine material. These unique sedimentary characteristics document the crucial role played by extreme precipitation from tropical disturbances in denuding this landscape.

Influence of sea squirt (Halocynthia roretzi) aquaculture on benthic-pelagic coupling in coastal waters: A study of the South Sea in Korea

NASA Astrophysics Data System (ADS)

Lee, Jae Seong; Kim, Sung-Han; Kim, Yong-Tae; Hong, Sok Jin; Han, Jeong Hee; Hyun, Jung-Ho; Shin, Kyung-Hoon

2012-03-01

The influence of sea squirt aquaculture on benthic-pelagic coupling was evaluated in semi-enclosed Korean coastal waters with an in situ benthic chamber and results show for the first time that suspended sea squirt cultures play an important role in benthic-pelagic coupling in the coastal zone. Measurements of primary production, vertical particulate fluxes, and benthic fluxes were made at two stations, a sea squirt (Halocynthia roretzi) farm (SSF) and an area of organic-matter-enriched sediment in Jinhae Bay. The vertical material fluxes of organic carbon, nitrogen, and biogenic silicate (BSi) were significantly higher at SSF than in Jinhae Bay, indicating massive biodeposits in the surface sediments at SSF. The organic carbon oxidation rates (Cox) were estimated after correction for CaCO3 dissolution. The average Cox at SSF (204 mmol C m-2 d-1) was significantly higher than that in the organic-enriched Jinhae Bay sediment (77 mmol C m-2 d-1). The organic carbon burial fluxes were determined using vertical profiles of organic carbon of up to 30 cm and the sedimentation rate calculated from the excess 210Pb distribution. At both stations, ˜95% of the settled organic carbon was oxidized and only ˜5% was buried in the deep sediment layer. The benthic fluxes of dissolved inorganic nitrogen and phosphate at SSF were 2-12 times higher than in Jinhae Bay, corresponding to 85%, and 270%, respectively, of the requirements for primary production.

Spatial and temporal variability in sedimentation rates associated with cutoff channel infill deposits: Ain River, France

USGS Publications Warehouse

Piégay, H.; Hupp, C.R.; Citterio, A.; Dufour, S.; Moulin, B.; Walling, D.E.

2008-01-01

Floodplain development is associated with lateral accretion along stable channel geometry. Along shifting rivers, the floodplain sedimentation is more complex because of changes in channel position but also cutoff channel presence, which exhibit specific overflow patterns. In this contribution, the spatial and temporal variability of sedimentation rates in cutoff channel infill deposits is related to channel changes of a shifting gravel bed river (Ain River, France). The sedimentation rates estimated from dendrogeomorphic analysis are compared between and within 14 cutoff channel infills. Detailed analyses along a single channel infill are performed to assess changes in the sedimentation rates through time by analyzing activity profiles of the fallout radionuclides 137Cs and unsupported 210Pb. Sedimentation rates are also compared within the channel infills with rates in other plots located in the adjacent floodplain. Sedimentation rates range between 0.65 and 2.4 cm a−1 over a period of 10 to 40 years. The data provide additional information on the role of distance from the bank, overbank flow frequency, and channel geometry in controlling the sedimentation rate. Channel infills, lower than adjacent floodplains, exhibit higher sedimentation rates and convey overbank sediment farther away within the floodplain. Additionally, channel degradation, aggradation, and bank erosion, which reduce or increase the distance between the main channel and the cutoff channel aquatic zone, affect local overbank flow magnitude and frequency and therefore sedimentation rates, thereby creating a complex mosaic of sedimentation zones within the floodplain and along the cutoff channel infills. Last, the dendrogeomorphic and 137Cs approaches are cross validated for estimating the sedimentation rate within a channel infill.

Sediment Loading from Crab Creek and Other Sources to Moses Lake, Washington, 2007 and 2008

USGS Publications Warehouse

Magirl, Christopher S.; Cox, Stephen E.; Mastin, Mark C.; Huffman, Raegan L.

2010-01-01

The average sediment-accumulation rate on the bed of Moses Lake since 1980, based on the identification of Mount St. Helens ash in lakebed cores, was 0.24 inches per year. Summed over the lake surface area, the average sediment-accumulation rate on the lakebed is 190,000 tons per year. Based on USGS stream-gaging station data, the average annual sediment load to Moses Lake from Crab Creek was 32,000 tons per year between 1943 and 2008; the post Mount St. Helens eruption annual load from Crab Creek was calculated to be 13,000 tons per year. The total mass input from Crab Creek and other fluvially derived sediment sources since 1980 has been about 20,000 tons per year. Eolian sediment loading to Moses Lake was about 50,000 tons per year before irrigation and land-use development largely stabilized the Moses Lake dune field. Currently, eolian input to the lake is less than 2,000 tons per year. Considering all sediment sources to the lake, most (from 80 to 90 percent) of post-1980 lakebed-sediment accumulation is from autochthonous, or locally formed, mineral matter, including diatom frustuals and carbonate shells, derived from biogenic production in phytoplankton and zooplankton. Suspended-sediment samples collected from Crab Creek and similar nearby waterways in 2007 and 2008 combined with other USGS data from the region indicated that a proposed Bureau of Reclamation supplemental feed of as much as 650 cubic feet per second through Crab Creek might initially contain a sediment load of as much as 1,500 tons per day. With time, however, this sediment load would decrease to about 10 tons per day in the sediment-supply-limited creek as available sediment in the channel is depleted. Sediment loads in the supplemental feed ultimately would be similar to loads in other bypass canals near Moses Lake. Considering the hydrology and geomorphology of the creek over multiple years, there is little evidence that the proposed supplemental feed would substantially increase the overall sediment load from Crab Creek to Moses Lake relative to natural, background conditions. Because Moses Lake is relatively shallow and subject to significant wind-driven circulation currents, mixing also would redistribute some of the fluvial sediment load deposited from Crab Creek throughout Parker Horn and the rest of Moses Lake, further mitigating the local effect of Crab Creek sedimentation near the City of Moses Lake.

Comparing polychlorinated biphenyl concentrations and patterns in the Saginaw River using sediment, caged fish, and semipermeable membrane devices

USGS Publications Warehouse

Echols, K.R.; Gale, R.W.; Schwartz, T.R.; Huckins, J.N.; Williams, L.L.; Meadows, J.C.; Morse, D.; Petty, J.D.; Orazio, C.E.; Tillitt, D.E.

2000-01-01

Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, MI, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in caged fish, and 77 to 790 ng/g in SPMDs. Previously reported rates of PCB accumulation by SPMDs were used to estimate aqueous concentrations from the PCB concentrations detected in the SPMDs. Sediment-water partition coefficients were used to estimate aqueous PCB concentrations from sediment. Steady-state bioconcentration factors and depuration rate constants were used to estimate dissolved PCB concentrations from caged channel catfish. Relative PCB patterns from the SPMDs, caged fish, and sediment were compared using principal components analysis. SPMD and sediment samples provide complementary information. Sediments reflect long-term accumulation and weathering, while SPMDs integrate water concentrations only during the sampling period. Because of higher water solubilities of lower-chlorinated PCBs these predominate in the SPMDs as compared to in the fish and sediments. Contaminant profile differences between caged fish and SPMDs are likely due to metabolism and depuration of certain PCB congeners by fish.Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, Ml, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in caged fish, and 77 to 790 ng/g in SPMDs. Previously reported rates of PCB accumulation by SPMDs were used to estimate aqueous concentrations from the PCB concentrations detected in the SPMDs. Sediment-water partition coefficients were used to estimate aqueous PCB concentrations from sediment. Steady-state bioconcentration factors and depuration rate constants were used to estimate dissolved PCB concentrations from caged channel catfish. Relative PCB patterns from the SPMDs, caged fish, and sediment were compared using principal components analysis. SPMD and sediment samples provide complementary information. Sediments reflect long-term accumulation and weathering, while SPMDs integrate water concentrations only during the sampling period. Because of higher water solubilities of lower-chlorinated PCBs these predominate in the SPMDs as compared to in the fish and sediments. Contaminant profile differences between caged fish and SPMDs are likely due to metabolism and depuration of certain PCB congeners by fish.At five sites in the Saginaw River, MI, PCB concentrations were determined in the summer of 1993 using three methods: sediment analysis, concentrations in caged fish, and concentrations in semipermeable membrane devices (SPMDs). On average, total PCB concentrations in the SPMDs were twice those found in caged fish, and the SPMD-to-fish concentration ratios of di-, tri-, tetra-, and pentaCB homologues were 10.0, 3.0, 2.5, and 1.4, respectively. Average concentrations in the sediments were approximately half those in the SPMDs, and the caged fish showed a greater preponderance of higher log octanol-water partition coefficient PCBs similar to the sediment pattern. On average, the water PCB concentrations estimated from sediment concentrations were five times higher than those calculated from SPMDs and three times higher than those estimated from caged fish. The total PCB concentrations in sediment, caged fish, and SPMDs ranged 33-280, 46-290, and 77-790 ng/g, respectiv

Geochemical modeling of iron, sulfur, oxygen and carbon in a coastal plain aquifer

USGS Publications Warehouse

Brown, C.J.; Schoonen, M.A.A.; Candela, J.L.

2000-01-01

Fe(III) reduction in the Magothy aquifer of Long Island, NY, results in high dissolved-iron concentrations that degrade water quality. Geochemical modeling was used to constrain iron-related geochemical processes and redox zonation along a flow path. The observed increase in dissolved inorganic carbon is consistent with the oxidation of sedimentary organic matter coupled to the reduction of O2 and SO4/2- in the aerobic zone, and to the reduction of SO4/2- in the anaerobic zone; estimated rates of CO2 production through reduction of Fe(III) were relatively minor by comparison. The rates of CO2 production calculated from dissolved inorganic carbon mass transfer (2.55 x 10-4 to 48.6 x 10-4 mmol 1-1 yr-1) generally were comparable to the calculated rates of CO2 production by the combined reduction of O2, Fe(III) and SO4/2- (1.31 x 10-4 to 15 x 10-4 mmol 1-1 yr-1). The overall increase in SO4/2- concentrations along the flow path, together with the results of mass-balance calculations, and variations in ??34S values along the flow path indicate that SO4/2- loss through microbial reduction is exceeded by SO4/2- gain through diffusion from sediments and through the oxidation of FeS2. Geochemichal and microbial data on cores indicate that Fe(III) oxyhydroxide coatings on sediment grains in local, organic carbon- and SO4/2- -rich zones have localized SO4/2- -reducing zones in which the formation of iron disulfides been depleted by microbial reduction and resulted in decreases dissolved iron concentrations. These localized zones of SO4/2- reduction, which are important for assessing zones of low dissolved iron for water-supply development, could be overlooked by aquifer studies that rely only on groundwater data from well-water samples for geochemical modeling. (C) 2000 Elsevier Science B.V.Fe(III) reduction in the Magothy aquifer of Long Island, NY, results in high dissolved-iron concentrations that degrade water quality. Geochemical modeling was used to constrain iron-related geochemical processes and redox zonation along a flow path. The observed increase in dissolved inorganic carbon is consistent with the oxidation of sedimentary organic matter coupled to the reduction of O2 and SO42- in the aerobic zone, and to the reduction of SO42- in the anaerobic zone; estimated rates of CO2 production through reduction of Fe(III) were relatively minor by comparison. The rates of CO2 production calculated from dissolved inorganic carbon mass transfer (2.55??10-4 to 48.6??10-4mmol l-1yr-1) generally were comparable to the calculated rates of CO2 production by the combined reduction of O2, Fe(III) and SO42- (1.31??10-4 to 15??10-4mmol l-1yr-1). The overall increase in SO42- concentrations along the flow path, together with the results of mass-balance calculations, and variations in ??34S values along the flow path indicate that SO42- loss through microbial reduction is exceeded by SO42- gain through diffusion from sediments and through the oxidation of FeS2. Geochemical and microbial data on cores indicate that Fe(III) oxyhydroxide coatings on sediment grains in local, organic carbon- and SO42--rich zones have been depleted by microbial reduction and resulted in localized SO42--reducing zones in which the formation of iron disulfides decreases dissolved iron concentrations. These localized zones of SO42- reduction, which are important for assessing zones of low dissolved iron for water-supply development, could be overlooked by aquifer studies that rely only on groundwater data from well-water samples for geochemical modeling.

Effects of Atrazine, Metolachlor, Carbaryl and Chlorothalonil on Benthic Microbes and Their Nutrient Dynamics

PubMed Central

Elias, Daniel; Bernot, Melody J.

2014-01-01

Atrazine, metolachlor, carbaryl, and chlorothalonil are detected in streams throughout the U.S. at concentrations that may have adverse effects on benthic microbes. Sediment samples were exposed to these pesticides to quantify responses of ammonium, nitrate, and phosphate uptake by the benthic microbial community. Control uptake rates of sediments had net remineralization of nitrate (−1.58 NO3 µg gdm−1 h−1), and net assimilation of phosphate (1.34 PO4 µg gdm−1 h−1) and ammonium (0.03 NH4 µg gdm−1 h−1). Metolachlor decreased ammonium and phosphate uptake. Chlorothalonil decreased nitrate remineralization and phosphate uptake. Nitrate, ammonium, and phosphate uptake rates are more pronounced in the presence of these pesticides due to microbial adaptations to toxicants. Our interpretation of pesticide availability based on their water/solid affinities supports no effects for atrazine and carbaryl, decreasing nitrate remineralization, and phosphate assimilation in response to chlorothalonil. Further, decreased ammonium and phosphate uptake in response to metolachlor is likely due to affinity. Because atrazine target autotrophs, and carbaryl synaptic activity, effects on benthic microbes were not hypothesized, consistent with results. Metolachlor and chlorothalonil (non-specific modes of action) had significant effects on sediment microbial nutrient dynamics. Thus, pesticides with a higher affinity to sediments and/or broad modes of action are likely to affect sediment microbes' nutrient dynamics than pesticides dissolved in water or specific modes of action. Predicted nutrient uptake rates were calculated at mean and peak concentrations of metolachlor and chlorothalonil in freshwaters using polynomial equations generated in this experiment. We concluded that in natural ecosystems, peak chlorothalonil and metolachlor concentrations could affect phosphate and ammonium by decreasing net assimilation, and nitrate uptake rates by decreasing remineralization, relative to mean concentrations of metolachlor and chlorothalonil. Our regression equations can complement models of nitrogen and phosphorus availability in streams to predict potential changes in nutrient dynamics in response to pesticides in freshwaters. PMID:25275369

Effects of Sediment Patches on Sediment Transport Predictions in Steep Mountain Channels

NASA Astrophysics Data System (ADS)

Monsalve Sepulveda, A.; Yager, E.

2013-12-01

Bed surface patches occur in most gravel-bedded rivers and in steep streams can be divided between relatively immobile boulders and more mobile patches of cobbles and gravel. This spatial variability in grain size, roughness and sorting impact bed load transport by altering the relative local mobility of different grain sizes and creating complex local flow fields. Large boulders also bear a significant part of the total shear stress and we hypothesize that the remaining shear stress on a given mobile patch is a distribution of values that depend on the local topography, patch type and location relative to the large roughness elements and thalweg. Current sediment transport equations do not account for the variation in roughness, local flow and grain size distributions on and between patches and often use an area-weighted approach to obtain a representative grain size distribution and reach-averaged shear stress. Such equations also do not distinguish between active (patches where at least one grain size is in motion) and inactive patches or include the difference in mobility between patch classes as result of spatial shear stress distributions. To understand the effects of sediment patches on sediment transport in steep channels, we calculated the shear stress distributions over a range of patch classes in a 10% gradient step-pool stream. We surveyed the bed with a high density resolution (every 5 cm in horizontal and vertical directions over a 40 m long reach) using a total station and terrestrial LiDAR, mapped and classified patches by their grain size distributions, and measured water surface elevations and mean velocities for low to moderate flow events. Using these data we calibrated a quasi-three dimensional model (FaSTMECH) to obtain shear stress distributions over each patch for a range of flow discharges. We modified Parker's (1990) equations to use the calculated shear stress distribution, measured grain sizes, and a specific hiding function for each patch class, and then added the bedload fluxes for each patch to calculate the reach-averaged sediment transport rate. Sediment mobility in patches was highly dependent on the patch's class and location relative to the thalweg and large roughness elements. Compared to deterministic formulations, the use of distributions of shear stress improved predictions of bedload transport in steep mountain channels.

Controlling suspended sediment samplers by programmable calculator and interface circuitry

Treesearch

Rand E. Eads; Mark R. Boolootian

1985-01-01

A programmable calculator connected to an interface circuit can control automatic samplers and record streamflow data. The circuit converts a voltage representing water stage to a digital signal. The sampling program logs streamflow data when there is a predefined deviation from a linear trend in the water elevation. The calculator estimates suspended sediment...

Today's sediment budget of the Rhine River channel, focusing on the Upper Rhine Graben and Rhenish Massif

NASA Astrophysics Data System (ADS)

Frings, Roy M.; Gehres, Nicole; Promny, Markus; Middelkoop, Hans; Schüttrumpf, Holger; Vollmer, Stefan

2014-01-01

The river bed of the Rhine River is subject to severe erosion and sedimentation. Such high geomorphological process rates are unwanted for economical, ecological, and safety reasons. The objectives of this study were (1) to quantify the geomorphological development of the Rhine River between 1985 and 2006; (2) to investigate the bed erosion process; and (3) to distinguish between tectonic, hydrological, and human controls. We used a unique data set with thousands of bedload and suspended-load measurements and quantified the fluxes of gravel, sand, silt, and clay through the northern Upper Rhine Graben and the Rhenish Massif. Furthermore, we calculated bed level changes and evaluated the sediment budget of the channel. Sediment transport rates were found to change in the downstream direction: silt and clay loads increase because of tributary supply; sand loads increase because of erosion of sand from the bed; and gravel loads decrease because of reduced sediment mobility caused by the base-level control exerted by the uplifting Rhenish Massif. This base-level control shows tectonic setting, in addition to hydrology and human interventions, to represent a major control on morphodynamics in the Rhine. The Rhine bed appears to be in a state of disequilibrium, with an average net bed degradation of 3 mm/a. Sand being eroded from the bed is primarily washed away in suspension, indicating a rapid supply of sand to the Rhine delta. The degradation is the result of an increased sediment transport capacity caused by nineteenth and twentieth century's river training works. In order to reduce degradation, huge amounts of sediment are fed into the river by river managers. Bed degradation and artificial sediment feeding represent the major sources of sand and gravel to the study area; only small amounts of sediment are supplied naturally from upstream or by tributaries. Sediment sinks include dredging, abrasion, and the sediment output to the downstream area. Large uncertainties exist about the amounts of sediment deposited on floodplains and in groyne fields. Compared to the natural situation during the middle Holocene, the present-day gravel and sand loads seem to be lower, whereas the silt and clay loads seem to be higher. This is probably caused by the present-day absence of meander migration, the deforestation, and the reduced sediment trapping efficiency of the floodplains. Even under natural conditions no equilibrium bed level existed.

Stepwise morphological evolution of the active Yellow River (Huanghe) delta lobe (1976-2013): Dominant roles of riverine discharge and sediment grain size

NASA Astrophysics Data System (ADS)

Wu, Xiao; Bi, Naishuang; Xu, Jingping; Nittrouer, Jeffrey A.; Yang, Zuosheng; Saito, Yoshiki; Wang, Houjie

2017-09-01

The presently active Yellow River (Huanghe) delta lobe has been formed since 1976 when the river was artificially diverted. The process and driving forces of morphological evolution of the present delta lobe still remain unclear. Here we examined the stepwise morphological evolution of the active Yellow River delta lobe including both the subaerial and the subaqueous components, and illustrated the critical roles of riverine discharge and sediment grain size in dominating the deltaic evolution. The critical sediment loads for maintaining the delta stability were also calculated from water discharge and sediment load measured at station Lijin, the last gauging station approximately 100 km upstream from the river mouth. The results indicated that the development of active delta lobe including both subaerial and subaqueous components has experienced four sequential stages. During the first stage (1976-1981) after the channel migration, the unchannelized river flow enhanced deposition within the channel and floodplain between Lijin station and the river mouth. Therefore, the critical sediment supply calculated by the river inputs obtained from station Lijin was the highest. However, the actual sediment load at this stage (0.84 Gt/yr) was more than twice of the critical sediment load ( 0.35 Gt/yr) for sustaining the active subaerial area, which favored a rapid seaward progradation of the Yellow River subaerial delta. During the second stage (1981-1996), the engineering-facilitated channelized river flow and the increase in median grain size of suspended sediment delivered to the sea resulted in the critical sediment load for keeping the delta stability deceasing to 0.29 Gt/yr. The active delta lobe still gradually prograded seaward at an accretion rate of 11.9 km2/yr at this stage as the annual sediment load at Lijin station was 0.55 Gt/yr. From 1996 to 2002, the critical sediment load further decreased to 0.15 Gt/yr with the sediment grain size increased to 22.5 μm; however, the delta suffered net erosion because of the insufficient sediment supply (0.11 Gt/yr). In the most recent stage (2002 - 2013), the intensive scouring of the lower river channel induced by the dam regulation provided relatively coarser sediment, which effectively reduced the critical sediment load to 0.06 Gt/yr, much lower than the corresponding sediment load at Lijin station ( 0.16 Gt/yr). Consequently, the subaerial Yellow River delta transitioned to a slight accretion phase. Overall, the evolution of the active Yellow River delta is highly correlated to riverine water and sediment discharge. The sediment supply for keeping the subaerial delta stability is inconstant and varying with the river channel morphology and sediment grain size. We conclude that the human-impacted riverine sediment discharge and grain-size composition play dominant roles in the stepwise morphological evolution of the active delta lobe.

Geomorphology-based interpretation of sedimentation rates from radiodating, lower Passaic River, New Jersey, USA.

PubMed

Erickson, Michael J; Barnes, Charles R; Henderson, Matthew R; Romagnoli, Robert; Firstenberg, Clifford E

2007-04-01

Analysis of site geomorphology and sedimentation rates as an indicator of long-term bed stability is central to the evaluation of remedial alternatives for depositional aquatic environments. In conjunction with various investigations of contaminant distribution, sediment dynamics, and bed stability in the Passaic River Estuary, 121 sediment cores were collected in the early 1990s from the lower 9.7 km of the Passaic River and analyzed for lead-210 (210Pb), cesium-137 (137Cs), and other analytes. This paper opportunistically uses the extensive radiochemical dataset to examine the spatial patterns of long-term sedimentation rates in, and associated geomorphic aspects of, this area of the river. For the purposes of computing sedimentation rates, the utility of the 210Pb and 137Cs depositional profiles was assessed to inform appropriate interpretation. Sedimentation rates were computed for 90 datable cores by 3 different methods, depending on profile utility. A sedimentation rate of 0 was assigned to 17 additional cores that were not datable and for which evidence of no deposition exists. Sedimentation patterns were assessed by grouping results within similar geomorphic areas, delineated through inspection of bathymetric data. On the basis of channel morphology, results reflect expected patterns, with the highest sedimentation rates observed along point bars and channel margins. The lowest rates of sedimentation (and the largest percentage of undatable cores) were observed in the areas along the outer banks of channel bends. Increasing sedimentation rates from upstream to downstream were noted. Average and median sedimentation rates were estimated to be 3.8 and 3.7 cm/y, respectively, reflecting the highly depositional nature of the Passaic River estuary. This finding is consistent with published descriptions of long-term geomorphology for Atlantic Coastal Plain estuaries.

The interaction of unidirectional winds with an isolated barchan sand dune

NASA Technical Reports Server (NTRS)

Gad-El-hak, M.; Pierce, D.; Howard, A.; Morton, J. B.

1976-01-01

Velocity profile measurements are determined on and around a barchan dune model inserted in the roughness layer on the tunnel floor. A theoretical investigation is made into the factors influencing the rate of sand flow around the dune. Flow visualization techniques are employed in the mapping of streamlines of flow on the dune's surface. Maps of erosion and deposition of sand are constructed for the barchan model, utilizing both flow visualization techniques and friction velocities calculated from the measured velocity profiles. The sediment budget found experimentally for the model is compared to predicted and observed results reported. The comparison shows fairly good agreement between the experimentally determined and predicted sediment budgets.

Tracing erosion patterns in Taiwan by quantitative provenance and geomorphological analysis

NASA Astrophysics Data System (ADS)

Resentini, Alberto; Goren, Liran; Castelltort, Sebastien; Garzanti, Eduardo

2016-04-01

Taiwan is one of the world's foremost natural laboratories for studies of orogenesis. After only a few Ma of ongoing collision between the Chinese continental margin and the Luzon Arc, the associated orogen has reached nearly 4 km in height and 100-150 km in width. High rates of convergence leading to rapid rock uplift combine with the wet stormy climate of the sub-tropical typhoon belt to deliver annually an average detrital mass of 9500 t/km2. The doubly-vergent thrust belt is composed of more than 85% of sedimentary rocks dominant in the pro-wedge, but metamorphic rocks as young as < 10 Ma are exposed in the retro-wedge, where zircon fission-track, apatite fission-track and (U-Th)/He ages are all reset and as young as 1 Ma or younger, indicating very recent fast exhumation. There is hardly another region where rock-uplift, unroofing and sediment production are of equal intensity. Quantitative analyses of tectonic and erosional processes around Taiwan have been carried out following diverse independent ways, including estimates of fluvial discharge of suspended solids, thermochronological techniques, cosmogenic measurements, and morphometry of river profiles (Dadson et al., 2003; Willett et al., 2003; Fox et al., 2014). Also the appearance and relative abundance of diagnostic rock fragments and other detrital minerals in Plio-Pleistocene sedimentary successions has been used to constrain unroofing rates, but a systematic description of compositional signatures of sediments shed by distinct tectonic domains has not been carried out so far. In this study we combine high-resolution petrographic and heavy-mineral analyses of modern sands carried by rivers all around Taiwan with their estimated sediment loads to calculate the detrital volumes generated from different lithologic assemblages within the orogen. River sediments are potent integrators of information that efficiently mediate provenance signals from different parts of the entire watershed, thus offering a great advantage relative to techniques analysing bedrock. This strategy allows us to calculate the sediment mass shed by each tectonic unit within each sub-catchment, and thus to trace erosion rates with continuity in space both along and across the orogenic belt. The results obtained were compared with the spatial pattern of estimated fluvial erosion rates calculated across the island by applying the stream power analysis relating river incision to basal shear stress (Finlayson and Montgomery, 2003). Initial investigation of sources of discrepancies between provenance analysis and morphometric analysis points toward the importance of lithological control on fluvial incision within the stream power model framework. CITED REFERENCES Dadson S.J., Hovius N., Chen H., Dade W.B., Hsieh M.L., Willett S.D., Hu J.C., Horng M.J., Chen, M.C., Stark, C.P., Lague D., Lin J.C. 2003. Links between erosion, runoff variability and seismicity in the Taiwan orogen. Nature 426:648-651. Finlayson D.P., Montgomery D.R. 2003. Modeling large-scale fluvial erosion in geographic information systems. Geomorphology 53:147-164. Fox M., Goren L., May D.A., Willett S.D. 2014. Inversion of fluvial channels for paleorock uplift rates in Taiwan. Journal of Geophysical Research: Earth Surface 119:1853-1875. Willett S.D., Fisher D., Fuller C., Yeh E.C., Lu C.Y. 2003. Erosion rates and orogenic-wedge kinematics in Taiwan inferred from fission-track thermochronometry. Geology 31:945-948.

The coevolution of bed roughness, grain clustering, surface armoring, hydraulic roughness, and sediment transport rate in experimental coarse alluvial channels: implications for long-term effects of gravel augmentation

NASA Astrophysics Data System (ADS)

Johnson, J. P.; Aronovitz, A. C.

2012-12-01

We conducted laboratory flume experiments to quantify changes in multiple factors leading to mountain river bed stability (i.e., minimal bed changes in space and time), and to understand how stable beds respond to perturbations in sediment supply. Experiments were run in a small flume 4 m long by 0.1 m wide. We imposed an initial well-graded size distribution of sediment (from coarse sand to up to 4 cm clasts), a steady water discharge (0.9 L/s), and initial bed surface slopes (8% and 12%). We measured outlet sediment flux and size distribution, bed topography and surface size distributions, and water depths; from these we calculated total shear stress, form drag and skin friction stress partitioning, and hydraulic roughness. The bed was initially allowed to stabilize with no imposed upstream sediment flux. This stabilization occurred due to significant changes in all of the factors listed in the title, and resulted in incipient step-pool like bed morphologies. In addition, this study was designed to explore possible long-term effects of gravel augmentation on mountain channel morphology and surface grain size. While the short-term goal of gravel augmentation is usually to cause fining of surface sediment patches, we find that the long-term effects may be opposite. We perturbed the stabilized channels by temporarily imposing an upstream sediment flux of the finest sediment size fraction (sand to granules). Median surface sizes initially decreased due to fine sediment deposition, although transport rates of intermediate-sized grains increased. When the fine sediment supply was stopped, beds evolved to be both rougher and coarser than they had been previously, because the largest grains remained on the bed but intermediate-sized grains were preferentially transported out, leaving higher fractions of larger grains on the surface. Existing models for mixed grain size transport actually predict changes in mobilization reasonably well, but do not explicity account for surface roughness evolution. Our results indicate a nonlinear relationship between surface median grain size and bed roughness.

Extraterrestrial 3He in Paleocene sediments from Shatsky Rise: Constraints on sedimentation rate variability

NASA Astrophysics Data System (ADS)

Marcantonio, Franco; Thomas, Deborah J.; Woodard, Stella; McGee, David; Winckler, Gisela

2009-09-01

We attempt to constrain the variability of the flux of extraterrestrial 3He in the Paleocene by studying sediments from Shatsky Rise (Ocean Drilling Program, ODP Leg 198) that have tight orbital age control. 3He concentrations in Shatsky Rise sediments vary periodically at high frequency by about a factor of 6 over the 800-ka record analyzed. Virtually all of the sedimentary 3He (> 99.98%) is of extraterrestrial origin. The total helium in the sediments can be explained as a binary mixture of terrestrial and extraterrestrial components. We calculate an average 3He/ 4He ratio for the extraterrestrial endmember of 2.41 ± 0.29 × 10 - 4 , which is, remarkably, equal to that measured in present-day interplanetary dust particles. We determine a constant extraterrestrial 3He flux of 5.9 ± 0.9 × 10 - 13 cm 3STP .cm - 2 ka - 1 for our 800-ka Paleocene record at ~ 58 Ma. This value is identical within error to those for the late Paleocene in sediments from the northern Pacific and the Weddell Sea. Bulk sediment MARs (derived using a constant extraterrestrial 3He flux) respond to climate-forced carbonate preservation cycles and changes in eolian flux over the late Paleocene. This is the first direct evidence for significant changes in dust accumulation in response to eccentricity forcing during a greenhouse climate interval.

Population Ecology of Nitrifiers in a Stream Receiving Geothermal Inputs of Ammonium

PubMed Central

Cooper, A. Bryce

1983-01-01

The distribution, activity, and generic diversity of nitrifying bacteria in a stream receiving geothermal inputs of ammonium were studied. The high estimated rates of benthic nitrate flux (33 to 75 mg of N · m−2 · h−1) were a result of the activity of nitrifiers located in the sediment. Nitrifying potentials and ammonium oxidizer most probable numbers in the sediments were at least one order of magnitude higher than those in the waters. Nitrifiers in the oxygenated surface (0 to 2 cm) sediments were limited by suboptimal temperature, pH, and substrate level. Nitrifiers in deep (nonsurface) oxygenated sediments did not contribute significantly to the changes measured in the levels of inorganic nitrogen species in the overlying waters and presumably derived their ammonium supply from ammonification within the sediment. Ammonium-oxidizing isolates obtained by a most-probable number nonenrichment procedure were species of either Nitrosospira or Nitrosomonas, whereas all those obtained by an enrichment procedure (i.e., selective culture) were Nitrosomonas spp. The efficiency of the most-probable-number method for enumerating ammonium oxidizers was calculated to be between 0.05 and 2.0%, suggesting that measurements of nitrifying potentials provide a better estimate of nitrifying populations. PMID:16346261

Means and method of sampling flow related variables from a waterway in an accurate manner using a programmable calculator

Treesearch

Rand E. Eads; Mark R. Boolootian; Steven C. [Inventors] Hankin

1987-01-01

Abstract - A programmable calculator is connected to a pumping sampler by an interface circuit board. The calculator has a sediment sampling program stored therein and includes a timer to periodically wake up the calculator. Sediment collection is controlled by a Selection At List Time (SALT) scheme in which the probability of taking a sample is proportional to its...

Seasonal and inter-annual dynamics of suspended sediment at the mouth of the Amazon river: The role of continental and oceanic forcing, and implications for coastal geomorphology and mud bank formation

NASA Astrophysics Data System (ADS)

Gensac, Erwan; Martinez, Jean-Michel; Vantrepotte, Vincent; Anthony, Edward J.

2016-04-01

Fine-grained sediments supplied to the Ocean by the Amazon River and their transport under the influence of continental and oceanic forcing drives the geomorphic change along the 1500 km-long coast northward to the Orinoco River delta. The aim of this study is to give an encompassing view of the sediment dynamics in the shallow coastal waters from the Amazon River mouth to the Capes region (northern part of the Amapa region of Brazil and eastern part of French Guiana), where large mud banks are formed. Mud banks are the overarching features in the dynamics of the Amazon-Orinoco coast. They start migrating northward in the Capes region. Suspended Particulate Matter (SPM) concentrations were calculated from satellite products (MODIS Aqua and Terra) acquired over the period 2000-2013. The Census-X11 decomposition method used to discriminate short-term, seasonal and long-term time components of the SPM variability has rendered possible a robust analysis of the impact of continental and oceanic forcing. Continental forcing agents considered are the Amazon River water discharge, SPM concentration and sediment discharge. Oceanic forcing comprises modelled data of wind speed and direction, wave height and direction, and currents. A 150 km-long area of accretion is detected at Cabo Norte that may be linked with a reported increase in the river's sediment discharge concurrent with the satellite data study period. We also assess the rate of mud bank migration north of Cabo Norte, and highlight its variability. Although we confirm a 2 km y-1 migration rate, in agreement with other authors, we show that this velocity may be up to 5 km y-1 along the Cabo Orange region, and we highlight the effect of water discharge by major rivers debouching on this coastal mud belt in modulating such rates. Finally, we propose a refined sediment transport pattern map of the region based on our results and of previous studies in the area such as the AMASSEDS programme, and discuss the relationship between sediment transport and accumulation patterns and the coastal geomorphology of this region.

Effect of adsorbed metals ions on the transport of Zn- and Ni-EDTA complexes in a sand and gravel aquifer

USGS Publications Warehouse

Kent, D.B.; Davis, J.A.; Anderson, L.C.D.; Rea, B.A.; Coston, J.A.

2002-01-01

Adsorption, complexation, and dissolution reactions strongly influenced the transport of metal ions complexed with ethylenediaminetetraacetic acid (EDTA) in a predominantly quartz-sand aquifer during two tracer tests conducted under mildly reducing conditions at pH 5.8 to 6.1. In tracer test M89, EDTA complexes of zinc (Zn) and nickel (Ni), along with excess free EDTA, were injected such that the lower portion of the tracer cloud traveled through a region with adsorbed manganese (Mn) and the upper portion of the tracer cloud traveled through a region with adsorbed Zn. In tracer test S89, Ni- and Zn-EDTA complexes, along with excess EDTA complexed with calcium (Ca), were injected into a region with adsorbed Mn. The only discernable chemical reaction between Ni-EDTA and the sediments was a small degree of reversible adsorption leading to minor retardation. In the absence of adsorbed Zn, the injected Zn was displaced from EDTA complexes by iron(III) [Fe(III)] dissolved from the sediments. Displacement of Zn by Fe(III) on EDTA became increasingly thermodynamically favorable with decreasing total EDTA concentration. The reaction was slow compared to the time-scale of transport. Free EDTA rapidly dissolved aluminum (Al) from the sediments, which was subsequently displaced slowly by Fe. In the portion of tracer cloud M89 that traveled through the region contaminated with adsorbed Zn, little displacement of Zn complexed with EDTA was observed, and Al was rapidly displaced from EDTA by Zn desorbed from the sediments, in agreement with equilibrium calculations. In tracer test S89, desorption of Mn dominated over the more thermodynamically favorable dissolution of Al oxyhydroxides. Comparison with results from M89 suggests that dissolution of Al oxyhydroxides in coatings on these sediment grains by Ca-EDTA was rate-limited whereas that by free EDTA reached equilibrium on the time-scale of transport. Rates of desorption are much faster than rates of dissolution of Fe oxyhydroxides from sediment-grain surfaces and, therefore, adsorbed metal ions can strongly influence the speciation of ligands like EDTA in soils and sediments, especially over small temporal and spatial scales. Copyright ?? 2002 Elsevier Science Ltd.

A 20-15 ka high-resolution paleomagnetic secular variation record from Black Sea sediments - no evidence for the 'Hilina Pali excursion'?

NASA Astrophysics Data System (ADS)

Liu, Jiabo; Nowaczyk, Norbert R.; Frank, Ute; Arz, Helge W.

2018-06-01

A comprehensive magnetostratigraphic investigation on sixteen sediment cores from the southeastern Black Sea yielded a very detailed high-quality paleosecular variation (PSV) record spanning from 20 to 15 ka. The age models are based on radiocarbon dating, stratigraphic correlation, and tephrochronology. Further age constraints were obtained by correlating four meltwater events, described from the western Black Sea, ranging in age from about 17 to 15 ka, with maxima in K/Ti ratios, obtained from X-ray fluorescence (XRF) scanning, and minima in S-ratios, reflecting increased hematite content, in the studied cores. Since the sedimentation rates in the investigated time window are up to 50 cm ka-1, the obtained PSVs records enabled a stacking using 50-yr bins. A directional anomaly at 18.5 ka, associated with pronounced swings in inclination and declination, as well as a low in relative paleointensity (rPI), is probably contemporaneous with the Hilina Pali excursion, originally reported from Hawaiian lava flows. However, virtual geomagnetic poles (VGPs) calculated from Black Sea sediments are not located at latitudes lower than 60°N, which denotes normal, though pronounced secular variations. During the postulated Hilina Pali excursion, the VGPs calculated from Black Sea data migrated clockwise only along the coasts of the Arctic Ocean from NE Canada (20.0 ka), via Alaska (18.6 ka) and NE Siberia (18.0 ka) to Svalbard (17.0 ka), then looping clockwise through the Eastern Arctic Ocean.

Heavy Metal Enrichment in laminated lake sediments from N-Germany and N-Poland: Geochemical background, enrichment history and land surface changes

NASA Astrophysics Data System (ADS)

Hoelzmann, Philipp; Brauer, Achim; Dräger, Nadine; Kienel, Ulrike; Obremska, Milena; Ott, Florian; Słowinski, Michał

2017-04-01

For three lake sediment records, situated in rural environments in NE-Germany (Lake Tiefer See) and N-Poland (Lake Czechowskie, Lake Głęboczek), we present a detailed heavy metal enrichment history with sub-decadal resolution for the last 200 years. We determine the local and specific geogenic background values on the base of heavy-metal analysis of pre-industrial sediments and different sediment types (e.g. calcareous gyttja, organic gyttja etc.). These results provide means to calculate and quantify anthropogenic heavy metal accumulations and enrichment factors as well as to define regional measures for a state of reference, reflecting natural conditions without human impact. All three lakes show a similar pattern of relatively low heavy metal concentrations and only Pb, Zn and Cd show a clear parallel pattern of enrichment starting around 1850. This heavy metal enrichment mainly results from atmospheric input due to increasing industrialization within the framework of the Industrial Revolution. Highest concentrations of Cd, Zn, and Pb occur around 1960 to 1980 and thereafter a clear pattern of declining anthropogenic input is registered. This data is supplemented by calculations of mass accumulation rates to determine heavy metal input to the lakes for the past 200 years. For Lake Czechowskie the heavy metal input to the lake is compared to an on average five year resolved pollen record that reflects changes in land use and vegetation.

Sediment acoustic index method for computing continuous suspended-sediment concentrations

USGS Publications Warehouse

Landers, Mark N.; Straub, Timothy D.; Wood, Molly S.; Domanski, Marian M.

2016-07-11

Once developed, sediment acoustic index ratings must be validated with additional suspended-sediment samples, beyond the period of record used in the rating development, to verify that the regression model continues to adequately represent sediment conditions within the stream. Changes in ADVM configuration or installation, or replacement with another ADVM, may require development of a new rating. The best practices described in this report can be used to develop continuous estimates of suspended-sediment concentration and load using sediment acoustic surrogates to enable more informed and accurate responses to diverse sedimentation issues.

Longshore Sediment Transport on a Macrotidal Mixed Sediment Beach, Birling Gap, United Kingdom.

NASA Astrophysics Data System (ADS)

Curoy, J.; Moses, C. A.; Robinson, D. A.

2012-04-01

Mixed beaches (MBs), with sediment sizes ranging over three orders of magnitude, are an increasingly important coastal defence on > 1/3 of the shoreline of England and Wales. In East Sussex, the combined effect of coastal defence management schemes (extensive groyning and sea wall construction) has reduced beach sediment supply. Local authorities counteract the increased flood risk by recycling or artificially recharging beaches on the most vulnerable and populated areas. Beaches lose sediment predominantly via longshore transport (LST) whose accurate quantification is critical to calculating recharge amounts needed for effective beach management. Industry does this by using sediment transport modelling which depends on reliable input data and modelling assumptions. To improve understanding of processes and quantification of LST on MBs, this study has accurately measured sediment transport on a natural, macrotidal, MB. The 1.2 km natural MB at Birling Gap, East Sussex here is located on the downdrift end of an 80 km long sub-sedimentary cell and is oriented WNW-ESE. The beach lies on a low gradient chalk shore platform backed by sub-vertical chalk cliffs. It is composed primarily of flint gravel with a peak grain size distribution of 30 to 50 mm, and a sand content of up to 30%. Sediment transport was measured using pebble tracers and GPS surface surveys during three survey periods of three to five consecutive days in March, May and December 2006. Tracer pebbles, matching the beach pebbles' D50, were made of an epoxy resin with a copper core allowing their detection and recovery to a depth of 40 cm using a metal detector. Tracers were deployed on the upper, middle and lower beach, from the surface into the beach to depths of up to 40 cm. They were collected on the low tide following deployment. The wave conditions were recorded on a Valeport DWR wave recorder located seaward of the beach on the chalk platform. Over the three study periods a large spectrum of wave heights (0.1 to 2.6 m) and periods (2 and 13.4 s) was observed. Wave direction varied from 14 to 106° to the beach. In total, up to 300 tracers were used on every day of deployment. The recovery rate after one tide varied from 58.4 to 100%. Significant longshore transport was observed, up to a maximum of 145 m. The results show that pebble behaviour on a natural MB is extremely sensitive to position on the beach profile and to changes in the water level and wave conditions associated with tidal conditions. Longshore sediment transport rates ranged from 0 to 120.55 m3 tide-1. Longshore wave power and immersed longshore transport were calculated and a drift efficiency coefficient of 0.04 was derived. These results contribute to the data bank on LST on MBs. Ultimately they will help to refine the current models used by the industry and support beach managers in anticipating sediment volumes that will be necessary to sustain a MB prior to storm events. Key words: mixed beach, longshore sediment transport, sediment tracer.

Sedimentary connection between rock glaciers and torrential channels: definition, inventory and quantification from a test area in the south-western Swiss Alps

NASA Astrophysics Data System (ADS)

Kummert, Mario; Barboux, Chloé; Delaloye, Reynald

2017-04-01

Permafrsot creep is an important sediment transfer process in periglacial alpine hillslopes (Delaloye et al. 2010). Rock glaciers are the visible expression of mountain permafrost creep (Delaloye 2004). Large volumes of rock debris originating from headwalls, moraines and weathering deposits are slowly transported within rock glaciers from their rooting zone to their fronts. In the Alps, most rock glaciers can be considered as sediment traps, because the sediment output at their margin is usually limited (Gärtner-Roer 2012). However, cases of rock glacier supplying torrential channels with sediments have been documented (e.g. Lugon and Stoffel 2010, Delaloye et al. 2013) Such rock glaciers can act as a sediment source for the triggering of gravitational processes propagating further downstream. Moreover, in such configuration the amount of sediment available is not a finite volume but is gradually renewed or increased as the rock glacier advances. These cases are therefore very specific, especially in the perspective of natural hazards assessment and mitigation. However, in the Alps very little is known about such type of rock glaciers. In addition, the sediment transfer rates between the fronts of the rock glaciers and the torrents are often not known. In this context, our study aims at (i) defining better the configurations in which a sedimentary connection exists between rock glaciers and torrential channels, (ii) localizing the cases of active rock glaciers connected to the torrential network and (iii) estimating approximate sediment transfer rates between the fronts and the torrential gullies. For that purpose, an inventory method for the classification of torrential catchments based on the analysis of aerial images and the computation of connectivity indexes have been developped. In addition, sediment transfer rates were estimated taking into account the geometry of the frontal areas and the velocity rates of the rock glaciers derived from DInSAR data. In order to validate these estimations, the resulting sediment transfer rates are compared to transfer rates calculated from repeated terrestrial LiDAR surveys on selected study cases. This contribution presents results from the application of this methodology in a test study area in the south-western Swiss Alps. The methodology reveals itself suitable to identify rock glaciers connected to the torrential network. For each of the detected rock glaciers, an estimation of the sediment yield is proposed. The transfer rates range from tens of cubic meters per year for some slow moving and/or partially connected landforms, to several thousands of cubic meters per year. References: Delaloye R. (2004). Contribution à l'étude du pergélisol de montagne en zone marginale. GeoFocus vol. 10, Thèse, Département de Géosciences/Géographie, Université de Fribourg. Delaloye, R., Lambiel, C., Gärtner-Roer, I. (2010). Overview of rock glacier kinematics research in the Swiss Alps. Seasonal rhythm, interannual variations and trends over several decades. Geogr. Helv., 65: 2, 135-145. Delaloye, R., Morard, S., Barboux, C., Abbet, D., Gruber, V., Riedo, M. & Gachet, S. (2013). Rapidly moving rock glaciers in Mattertal. In: Graf, C. (Eds). Mattertal - ein Tal in Bewegung. Publikation zur Jahrestagung der Schweizerischen Geomorphologischen Gesellschaft 29. Juni - 1. Juli 2011, St. Niklaus, Birmensdorf, Eidg. Forschungsanstalt WSL, 113 - 124. Gärtner-Roer, I. (2012). Sediment transfer rates of two active rockglaciers in the Swiss Alps. Geomorphology, 167-168, 45-50. Lugon, R. & Stoffel, M. (2010). Rock glacier dynamics and magnitude-frequency relations of debris flows in a high-elevation watershed : Ritigraben, Swiss Alps. Global and Planetary Change, 73, 202-210.

The trophic biology of the holothurian Molpadia musculus at 3500 m in the Nazaré Canyon (NE Atlantic)

NASA Astrophysics Data System (ADS)

Amaro, T.; Bianchelli, S.; Billett, D. S. M.; Cunha, M. R.; Pusceddu, A.; Danovaro, R.

2010-04-01

Megafaunal organisms play a key role in the deep-sea ecosystem functioning. At 3500 m depth in the Nazaré Canyon, NE Atlantic, very high abundances of the infaunal holothurian Molpadia musculus were found. Sediment samples and holothurians were collected by ROV and experiments were conducted in situ in incubation chambers. The biochemical composition of the sediment (in terms of proteins, carbohydrates and lipids), the holothurians' gut contents and holothurians' faecal material were analysed. In the sediments, proteins were the dominant organic compound, followed by carbohydrates and lipids. In the holothurian gut contents, conversely, protein concentrations were higher than the other compounds and decreased significantly as the material passed through the digestive tract. About 33±1% of the proteins were digested already in the mid gut, with a final digestion rate equal to 67±1%. Carbohydrates and lipids were ingested in smaller amounts and digested with lower efficiencies (23±11% and 50±11%, respectively). As a result, biopolymeric C digestion rate was on average 62±3%. We also calculated that the entire holothurians' population could remove from the sediment about 0.49±0.13 g biopolymeric C and 0.13±0.03 g N m-2 d-1. These results suggest that the M. musculus plays a key role in the benthic tropho-dynamics and biogeochemical processes of the Nazaré Canyon.

Late Quaternary carbonate accumulation along eastern South Atlantic Ocean

NASA Astrophysics Data System (ADS)

Crabill, K.; Slowey, N. C.; Foreman, A. D.; Charles, C.

2016-12-01

Water masses originating from both the North Atlantic Ocean and the Southern Ocean intersect the Walvis Ridge and Namibian margin of southwest Africa. Changes in the distribution and properties of these water masses through time are reflected by variations in the nature of the sediments accumulating along this margin. A suite of piston and gravity cores that possess sediment records corresponding to the most recent glacial-interglacial cycles were collected from the water depth range of 550 to 3700 meters. Sediment dry bulk density, XRF analyses and the concentration of CaCO3 were precisely determined at regular depth intervals in these cores. Foraminiferal δ18O along with XRF Fe/Ca data provide an age-depth model for key cores. The age-depth model and dry bulk density will be used with the calcium carbonate contents to calculate the accumulation rates of CaCO3 during each MIS 1-5e. The spatial and temporal variability in both the CaCO3 content and the CaCO3 mass accumulation rates along the Namibian continental slope will be described. Based on comparisons of these two parameters, inferences will be made about how variations of CaCO3 production, dilution of by non-CaCO3 sediment components, and dissolution of CaCO3 due to changes in ocean circulation/climate have occurred during intervals of the last glacial-interglacial cycle.

Analysis and Tendencies of Metals and POPs in a Sediment Core from the Alvarado Lagoon System (ALS), Veracruz, Mexico.

PubMed

Botello, A V; Villanueva, F S; Rivera, R F; Velandia, A L; de la Lanza, G E

2018-07-01

This study focused on dating of a sediment core from the Alvarado Lagoon System, Veracruz, Mexico, calculating the sedimentation rate by using 210 Pb to determine the tendency towards pollution by polycyclic aromatic hydrocarbons, organochlorides, the metals Cd, Cr, Cu, Hg, Ni, Pb, and V, and organic matter content. The activity of total Pb and supported Pb in the samples was 83.1 and 29.5 Bq kg -1 , respectively, whereas the average estimated sedimentation rate was 0.48 ± 0.09 cm per year -1 . The organic matter values exhibited linear behavior throughout the historical profile, with values under 2.5%. Metal concentrations followed the order V > Cr > Ni > Cu > Pb > Hg > Cd. Variations found in Cr, Ni, Pb, and V concentrations are basically due to three meteorological phenomena that hit the region: hurricanes Gladys, Hilda, and Janet in September of 1955. V, Ni, and Hg input comes from anthropogenic and lithogenic sources. The presence of individual polycyclic aromatic hydrocarbons showed no ascending accumulation pattern over time, nor did it show any significant statistical correlation to OM. As for the organochlorine pesticides, 63.61% of the total sum of these compounds were from the ciclodienics family. Concentration of p,p'-DDT was observed only in the earliest profile, from 1929.

Radioisotopes in sedimentary study of the Black Sea and Caspian Sea

NASA Astrophysics Data System (ADS)

Laptev, Gennady; Voitsekhovych, Oleg V.

2013-04-01

Natural archives, such as lake or marine sediment, are widely used in erosion/sedimentation, water quality, climate change and eutrophication study alongside with the retrospective reanalysis of contaminants fluxes (trace metals, organic pollutants or radionuclides). In order to "read" information stored in sediment sequences a chronostatigraphic method have been developed and used since 1950s which is based upon variation of activity of 210Pb over the sediment profile, natural radioisotope of Uranium decay series with half-life 22 years, and hence valid for the last 100-150 years of recent sedimentation history. The 210Pb chronology is prone to be validated by other time-markers, such as artificial radionuclides globally dispersed after the nuclear weapons tests of 1960s or major accidents on NPP (the Chernobyl accident of 1986 or latest on the Fukushima Daiichi in 2011). In the last decade an intensive study using sediment cores collected from shelf and deep-sea areas in the Black Sea and the Caspian Sea have been undertaken within the framework of a number of international research projects organized by IAEA and UNOPS-GEF and devoted to environmental problems of this enclosed, and therefore sensitive to environmental impact, marine systems. Elaborative analysis of the experimental data and sediment age calculation have been done by application of CRS and CIC dating models to unsupported 210Pb activity over the sediment profile. Measured in sediment 137Cs and 241Am clearly showed well resolved Bomb test and Chernobyl fallout peaks and were used as markers in order to corroborate radiometrically determined age of sediment. Geochronological reconstruction of the fallout radionuclides inventory, fluxes and accumulation rate in the sediment of the Black Sea and Caspian Sea by application of combined radiometric dating technique proved to be very consistent with the historical data of atmospheric fallout observations of that artificial radionuclides recorded worldwide since nuclear era onset in early 1950s. Another finding of the initially radioactivity related to project was suitability of unmixed sediment cores recovered from the deep anoxic floor and continental slope of the Black Sea to be used for proxy reconstruction of the late Holocene climate variability in the region. This well preserved sediment are characteristic in finely laminated coccolith ooze (Unit I - approximate age 2000 years) overlaying above rich in organic matter sapropels of Unit II. Variations in accumulation rates of biogenic carbonate sediment fraction of Unit I were found to be satisfactory correlate with changes in winter SST anomaly calibrated in recent radiometricaly dated topmost sediment. Further development and rectification of the proposed interdisciplinary method is in progress.

Sediment chemoautotrophy in the coastal ocean

NASA Astrophysics Data System (ADS)

Vasquez-Cardenas, Diana; Meysman, Filip J. R.; van Breugel, Peter; Boschker, Henricus T. S.

2016-04-01

A key process in the biogeochemistry of coastal sediments is the reoxidation of reduced intermediates formed during anaerobic mineralization which in part is performed by chemoautotrophic micro-organisms. These microbes fix inorganic carbon using the energy derived from reoxidation reactions and in doing so can fix up to 32% of the CO2 released by mineralization. However the importance and distribution of chemoautotrophy has not been systematically investigated in these environments. To address these issues we surveyed nine coastal sediments by means of bacterial biomarker analysis (phospholipid derived fatty acids) combined with stable isotope probing (13C-bicarbonate) which resulted in an almost doubling of the number of observations on coastal sedimentary chemoautotrophy. Firstly, sediment chemoautotrophy rates from this study and rates compiled from literature (0.07 to 36 mmol C m-2 d-1) showed a power-law relation with benthic oxygen uptake (3.4 to 192 mmol O2 m-2 d-1). Benthic oxygen uptake was used as a proxy for carbon mineralization to calculate the ratio of the CO2 fixed by chemoautotrophy over the total CO2 released through mineralization. This CO2 efficiency was 3% in continental shelf, 9% in nearshore and 21% in salt marsh sediments. These results suggest that chemoautotrophy plays an important role in C-cycling in reactive intertidal sediments such as salt marshes rather than in the organic-poor, permeable continental shelf sediments. Globally in the coastal ocean our empirical results show that chemoautotrophy contributes ˜0.05 Pg C y-1 which is four times less than previous estimates. Secondly, five coastal sediment regimes were linked to the depth-distribution of chemoautotrophy: 1) permeable sediments dominated by advective porewater transport, 2) bioturbated sediments, and cohesive sediments dominated by diffusive porewater transport characterized by either 3) canonical sulfur oxidation, 4) nitrate-storing Beggiatoa, or 5) electrogenic sulfur oxidation. Sediments with an O2-H2S interface exhibited highest chemoautotrophy activity in the top centimeter via canonical sulfur oxidation, whereas in the presence of electrogenic sulfur oxidation a uniform distribution of chemoautotrophy throughout the top centimeters of the sediment was evidenced. Lowest dark carbon fixation was found in permeable advective-driven sediments with deep oxygen penetration resulting in higher subsurface than surface activity. Hence, the depth-distribution of chemoautotrophy in coastal sediments varies due to several biogeochemical characteristics such as grain size, organic carbon content, presence of filamentous sulfur oxidizing bacteria, and macrofaunal activity.

Measuring Fast-Temporal Sediment Fluxes with an Analogue Acoustic Sensor: A Wind Tunnel Study

PubMed Central

Poortinga, Ate; van Minnen, Jan; Keijsers, Joep; Riksen, Michel; Goossens, Dirk; Seeger, Manuel

2013-01-01

In aeolian research, field measurements are important for studying complex wind-driven processes for land management evaluation and model validation. Consequently, there have been many devices developed, tested, and applied to investigate a range of aeolian-based phenomena. However, determining the most effective application and data analysis techniques is widely debated in the literature. Here we investigate the effectiveness of two different sediment traps (the BEST trap and the MWAC catcher) in measuring vertical sediment flux. The study was performed in a wind tunnel with sediment fluxes characterized using saltiphones. Contrary to most studies, we used the analogue output of five saltiphones mounted on top of each other to determine the total kinetic energy, which was then used to calculate aeolian sediment budgets. Absolute sediment losses during the experiments were determined using a balance located beneath the test tray. Test runs were conducted with different sand sizes and at different wind speeds. The efficiency of the two traps did not vary with the wind speed or sediment size but was affected by both the experimental setup (position of the lowest trap above the surface and number of traps in the saltation layer) and the technique used to calculate the sediment flux. Despite this, good agreement was found between sediment losses calculated from the saltiphone and those measured using the balance. The results of this study provide a framework for measuring sediment fluxes at small time resolution (seconds to milliseconds) in the field. PMID:24058512

Measuring fast-temporal sediment fluxes with an analogue acoustic sensor: a wind tunnel study.

PubMed

Poortinga, Ate; van Minnen, Jan; Keijsers, Joep; Riksen, Michel; Goossens, Dirk; Seeger, Manuel

2013-01-01

In aeolian research, field measurements are important for studying complex wind-driven processes for land management evaluation and model validation. Consequently, there have been many devices developed, tested, and applied to investigate a range of aeolian-based phenomena. However, determining the most effective application and data analysis techniques is widely debated in the literature. Here we investigate the effectiveness of two different sediment traps (the BEST trap and the MWAC catcher) in measuring vertical sediment flux. The study was performed in a wind tunnel with sediment fluxes characterized using saltiphones. Contrary to most studies, we used the analogue output of five saltiphones mounted on top of each other to determine the total kinetic energy, which was then used to calculate aeolian sediment budgets. Absolute sediment losses during the experiments were determined using a balance located beneath the test tray. Test runs were conducted with different sand sizes and at different wind speeds. The efficiency of the two traps did not vary with the wind speed or sediment size but was affected by both the experimental setup (position of the lowest trap above the surface and number of traps in the saltation layer) and the technique used to calculate the sediment flux. Despite this, good agreement was found between sediment losses calculated from the saltiphone and those measured using the balance. The results of this study provide a framework for measuring sediment fluxes at small time resolution (seconds to milliseconds) in the field.

Impact of sea-level rise on Everglades carbon storage capacity in the Holocene

NASA Astrophysics Data System (ADS)

Jones, M.; Bernhardt, C. E.; Wingard, G. L. L.; Keller, K.; Stackhouse, B.; Landacre, B.

2017-12-01

Sea-level rise (SLR) and climate have driven environmental changes in South Florida over time. Florida Bay, a shallow carbonate bay located to the south of the Florida Peninsula, contains carbonate islands and mudbanks that formed over the last few thousand years and once comprised the freshwater Everglades. The islands, often ringed with mangroves, provide wildlife habitat, physical barriers to storm surge, tidal flux, and wave development along South Florida's coastline. Because most of South Florida is only 1-2 m above mean sea level, and IPCC AR5 projections of 0.26 to 0.98 m of SLR by 2100, vertical accommodation space could outpace sediment accretion in the southern freshwater Everglades and Florida Bay islands, impacting carbon (C) storage, as well as wildlife habitat and the ability to protect shorelines from coastal storms. We analyzed sediment cores that reached the Plio-Pleistocene limestone bedrock from four islands in Florida Bay to determine how floral and faunal communities and source C change in response to Holocene sea level transgression. We used pollen and mollusk assemblages, δ13C, and C/N ratios, along with radiometric dating, bulk density, and organic C content to calculate changes in C accumulation rates (CAR) over the last 4 ka, as deposition transitioned from freshwater peat to estuarine carbonate mud, to mangrove peat and ultimately to the hyper-saline playa-like carbonate sediments deposited today. Results show that CAR are more than twice as high in the basal freshwater Everglades peat than in the overlying estuarine sediments and slightly greater than the short-lived period of Rhizophora (red mangrove) peat accumulation. Avicennia (black mangrove) and playa-like environments have similar CAR as the estuarine carbonate mud and hypersaline carbonate sediments but accretion rates are less than the current rate of SLR. These results suggest that with current rates of accretion and SLR, these islands could disappear in <200 years, and the C storage capacity of the Florida Everglades could decrease significantly if the freshwater Everglades accretion rate cannot outpace SLR. Further, the expansion and persistence of high-accumulating Rhizophora peat is limited by elevated SLR, impacting coastline stability and wildlife habitat.

GOM Deepwater Horizon Oil Spill: A Time Series Analysis of Variations in Spilled Hydrocarbons

NASA Astrophysics Data System (ADS)

Palomo, C. M.; Yan, B.

2013-12-01

An estimated amount of 210 million gallons of crude oil was released into the Gulf of Mexico (GOM) from April 20th to July 15th 2010 during the Deepwater Horizon oil rig explosion. The spill caused a tremendous financial, ecological, environmental and health impact and continues to affect the GOM today. Variations in hydrocarbons including alkanes, hopanes and poly-cyclic aromatic hydrocarbons (PAHs) can be analyzed to better understand the oil spill and assist in oil source identification. Twenty-one sediment samples*, two tar ball samples and one surface water oil sample were obtained from distinct locations in the GOM and within varying time frames from May to December 2010. Each sample was extracted through the ASE 200 solvent extractor, concentrated down under nitrogen gas, purified through an alumina column, concentrated down again with nitrogen gas and analyzed via GC X GC-TOF MS. Forty-one different hydrocarbons were quantified in each sample. Various hydrocarbon 'fingerprints,' such as parental :alkylate PAH ratios, high molecular weight PAHs: low molecular weight alkane ratios, and carbon preference index were calculated. The initial objective of this project was to identify the relative hydrocarbon contributions of petrogenic sources and combustion sources. Based on the calculated ratios, it is evident that the sediment core taken in October of 2010 was greatly affected by combustion sources. Following the first month of the spill, oil in the gulf was burned in attempts to contain the spill. Combustion related sources have quicker sedimentation rates, and hydrocarbons from a combustion source essentially move into deeper depths quicker than those from a petrogenic source, as was observed in analyses of the October 2010 sediment. *Of the twenty-one sediment samples prepared, nine were quantified for this project.

The varying stability of benthic homes: hydrologic regime and sediment supply control the timing and intensity of bed mobility

NASA Astrophysics Data System (ADS)

Pfeiffer, A.; Finnegan, N. J.

2017-12-01

Gravel river beds provide an ephemeral architecture for the benthic inhabitants of river ecosystems. Periphyton and benthic macroinvertebrates that live on or within the gravel are subject to catastrophic disruption upon mobilization of the surface gravel during floods. Because sediment supply varies by orders of magnitude across North America, and rivers have adjusted to convey their imposed loads, river bed surface mobility varies enormously. Climate also varies widely across the continent, yielding a range of flood timing, duration, and intermittency. Together, the differences in sediment supply and hydrologic patterns result in diverse regimes of benthic habitat stability. To quantitatively characterize these regimes, we calculate decades-scale time series of estimated bed surface mobility using sediment transport equations (Wilcock and Crowe, 2003). The method requires measurements of the bed surface grainsize distribution, channel slope, and standard USGS stream gauging records. We calculate the fraction of the bed surface grain size distribution that is mobile at any given flow, as well as the intensity of transport. We use the time series of bed mobility to compare between rivers and regions. In many snowmelt-dominated rivers in Idaho, a period of moderate bed mobility (W* > 0.002) generally occurs during the annual melt, and can last for days. In rivers draining the central and northern Appalachians, bed mobility is comparatively rare and occurs during short duration floods. Rivers on the tectonically active West Coast tend to experience bed mobility during most winter storms, with brief (hours long) periods of high transport rates (W* > 0.02) during storm peaks. The timing and intensity of bed mobility varies with hydrologic regime and sediment supply; these contrasts in bed mobility lead to diverse structural templates for river ecosystems.

Channel morphometry, sediment transport, and implications for tectonic activity and surficial ages of Titan basins

USGS Publications Warehouse

Cartwright, R.; Clayton, J.A.; Kirk, R.L.

2011-01-01

Fluvial features on Titan and drainage basins on Earth are remarkably similar despite differences in gravity and surface composition. We determined network bifurcation (Rb) ratios for five Titan and three terrestrial analog basins. Tectonically-modified Earth basins have Rb values greater than the expected range (3.0-5.0) for dendritic networks; comparisons with Rb values determined for Titan basins, in conjunction with similarities in network patterns, suggest that portions of Titan's north polar region are modified by tectonic forces. Sufficient elevation data existed to calculate bed slope and potential fluvial sediment transport rates in at least one Titan basin, indicating that 75mm water ice grains (observed at the Huygens landing site) should be readily entrained given sufficient flow depths of liquid hydrocarbons. Volumetric sediment transport estimates suggest that ???6700-10,000 Titan years (???2.0-3.0??105 Earth years) are required to erode this basin to its minimum relief (assuming constant 1m and 1.5m flows); these lowering rates increase to ???27,000-41,000 Titan years (???8.0-12.0??105 Earth years) when flows in the north polar region are restricted to summer months. ?? 2011 Elsevier Inc.

Temporal and spatial patterns of wetland sedimentation, West Tennessee

USGS Publications Warehouse

Hupp, C.R.; Bazemore, D.E.

1993-01-01

Dendrogeomorphic techniques were used to describe and interpret patterns of sedimentation rates at two forested wetland sites in West Tennessee. Fifty-five sampling stations were established along transects upstream and downstream from bridge structures, and 515 trees were examined for depth of sediment accretion and cored for age determination. Temporal variation in sedimentation rate may be related more to stream channelization and agricultural activity than to bridge and causeway construction. Sedimentation rates have increased substantially in the last 28 years, although channelized streams may have overall lower rates than unchannelized streams. Comparisons of sedimentation rates from deposition over artificial markers (short term) with those determined from tree-ring analysis (long-term) indicate that trends are similar where hydrogeomorphic conditions have not been altered substantially. No tendency for increased sedimentation upstream from bridges was observed. Deposition rates were inversely correlated with elevation and degree of ponding. Downstream deposition of sand splays appears to be related to flow constrictions and may be extensive. Mean overall rates of sedimentation (between 0.24 and 0.28 cm year-1), determined dendrogeomorphically, are comparable with other published rates. ?? 1993.

NOAA National Status and Trends Program Twelfth Round Intercomparison Exercise Results for Trace Metals in Marine Sediments and Biological Tissues. National Status and Trends Program for marine environmental quality: Technical memo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willie, S.

1998-11-01

The report summarizes the results of the Twelfth Round Intercomparison for Trace Metals in Marine Sediments and Biological Tissues under the directive of the NOAA National Status and Trends Program. A total of forty-four participants were included in the exercise, including NOAA, USEPA, state, Austrailian, Canadian, Mexican and Argentinean laboratories. Two samples were sent by NRC to each participant, a marine sediment collected on the east coast of Canada and a freeze-dried mussel tissue. Laboratories were also asked to analyze two certified reference materials (CRMs) MESS-2 and CRM 2976. The elements to be determined were Al, Cr, Fe, Ni, Cu,more » Zn, As, Se, Ag, Cd, Sn, Hg, and Pb for both matrices, plus Be, Si, Mn, Sb, and Tl for the sediments. An accepted mean and confidence interval was calculated for each analyte in the two unknown samples, laboratory biases were identified and an overall rating of superior, good, fair or others were assigned to each laboratory.« less

Determination of radioactivity levels and heavy metal concentrations in seawater, sediment and anchovy (Engraulis encrasicolus) from the Black Sea in Rize, Turkey.

PubMed

Baltas, Hasan; Kiris, Erkan; Sirin, Murat

2017-03-15

Seawater, sediment and fish (anchovy) samples consumed in the Rize province of the Eastern Black Sea region of Turkey were collected from five different stations. The radioactivity levels ( 226 Ra, 232 Th, 40 K and 137 Cs) were determined in all the samples using a high-purity germanium detector. While 226 Ra, 232 Th and 40 K radionuclides were detected in all samples, the radionuclide concentration of 137 Cs, except for the sediment samples (mean activity is 9±1.4Bqkg -1 ), was not detected for the seawater and fish samples. The total annual effective dose rates from the ingestion of these radionuclides for fish were calculated using the measured activity concentrations in radionuclides and their ingested dose conversion factor. Also, the concentrations of some heavy metals in all the samples were determined. The activity and heavy metal concentration values that were determined for the seawater, sediment and fish samples were compared among the locations themselves and with literature values. Copyright © 2017 Elsevier Ltd. All rights reserved.

Carbon and sediment accumulation in the Everglades (USA) during the past 4000 years: rates, drivers, and sources of error

USGS Publications Warehouse

Glaser, Paul H.; Volin, John C.; Givnish, Thomas J.; Hansen, Barbara C. S.; Stricker, Craig A.

2012-01-01

Tropical and sub-tropical wetlands are considered to be globally important sources for greenhouse gases but their capacity to store carbon is presumably limited by warm soil temperatures and high rates of decomposition. Unfortunately, these assumptions can be difficult to test across long timescales because the chronology, cumulative mass, and completeness of a sedimentary profile are often difficult to establish. We therefore made a detailed analysis of a core from the principal drainage outlet of the Everglades of South Florida, to assess these problems and determine the factors that could govern carbon accumulation in this large sub-tropical wetland. Accelerator mass spectroscopy dating provided direct evidence for both hard-water and open-system sources of dating errors, whereas cumulative mass varied depending upon the type of method used. Radiocarbon dates of gastropod shells, nevertheless, seemed to provide a reliable chronology for this core once the hard-water error was quantified and subtracted. Long-term accumulation rates were then calculated to be 12.1 g m-2 yr-1 for carbon, which is less than half the average rate reported for northern and tropical peatlands. Moreover, accumulation rates remained slow and relatively steady for both organic and inorganic strata, and the slow rate of sediment accretion ( 0.2 mm yr-1) tracked the correspondingly slow rise in sea level (0.35 mm yr-1 ) reported for South Florida over the past 4000 years. These results suggest that sea level and the local geologic setting may impose long-term constraints on rates of sediment and carbon accumulation in the Everglades and other wetlands.

The fate, distribution, and toxicity of lindane in tests with Chironomus riparius: effects of bioturbation and sediment organic matter content.

PubMed

Goedkoop, Willem; Peterson, Märit

2003-01-01

In this laboratory study, we address the effect of Chironomus bioturbation (0, 2,000, 6,000, and 18,000 ind/m2) and sediment organic matter content (10, 20, and 40%) on the fate, distribution, and bioavailability of 14C-lindane under standardized conditions in toxicity tests with artificial sediment. The results show that both Chironomus burrowing activity and sediment organic matter strongly modify test conditions. Larval mortality and development were inversely related with Chironomus densities and lindane concentration. Sediment organic matter content affected larval development rates but not mortality. Partitioning of lindane between the sediment, overlying water, and interstitial water was affected negatively by Chironomus larval densities: however, sediment partitioning was positively affected by sediment organic matter content. Bioturbation by Chironomus resulted in a remobilization of particle-associated lindane to the interstitial and overlying water, implying an increase in the bioavailability of the test compound. Strong positive relationships were found between Chironomus densities and lindane concentrations in interstitial water. The presence of Chironomus also resulted in lower label recovery. Label recovery on sediment particles ranged from 49 to 61% of initially added label in microcosms without Chironomus, from 41 to 56% at low larval densities, and from 15 to 50% at high larval densities. These results show that large discrepancies may exist between nominal test concentrations (from test compound additions) and true exposure concentrations even under standardized test conditions, which can introduce a relatively large error term in risk assessments. Calculations show that volatilization may be a quantitatively important sink for test compounds.

Effects of brush management on the hydrologic budget and water quality in and adjacent to Honey Creek State Natural Area, Comal County, Texas, 2001-10

USGS Publications Warehouse

Banta, J. Ryan; Slattery, Richard N.

2011-01-01

The U.S. Geological Survey, in cooperation with the U.S. Department of Agriculture Natural Resources Conservation Service, the Edwards Region Grazing Lands Conservation Initiative, the Texas State Soil and Water Conservation Board, the San Antonio River Authority, the Edwards Aquifer Authority, Texas Parks and Wildlife, the Guadalupe Blanco River Authority, and the San Antonio Water System, evaluated the hydrologic effects of ashe juniper (Juniperus ashei) removal as a brush management conservation practice in and adjacent to the Honey Creek State Natural Area in Comal County, Tex. By removing the ashe juniper and allowing native grasses to reestablish in the area as a brush management conservation practice, the hydrology in the watershed might change. Using a simplified mass balance approach of the hydrologic cycle, the incoming rainfall was distributed to surface water runoff, evapotranspiration, or groundwater recharge. After hydrologic data were collected in adjacent watersheds for 3 years, brush management occurred on the treatment watershed while the reference watershed was left in its original condition. Hydrologic data were collected for another 6 years. Hydrologic data include rainfall, streamflow, evapotranspiration, and water quality. Groundwater recharge was not directly measured but potential groundwater recharge was calculated using a simplified mass balance approach. The resulting hydrologic datasets were examined for differences between the watersheds and between pre- and post-treatment periods to assess the effects of brush management. The streamflow to rainfall relation (expressed as event unit runoff to event rainfall relation) did not change between the watersheds during pre- and post-treatment periods. The daily evapotranspiration rates at the reference watershed and treatment watershed sites exhibited a seasonal cycle during the pre- and post-treatment periods, with intra- and interannual variability. Statistical analyses indicate the mean difference in daily evapotranspiration rates between the two watershed sites is greater during the post-treatment than the pre-treatment period. Average annual rainfall, streamflow, evapotranspiration, and potential groundwater-recharge conditions were incorporated into a single hydrologic budget (expressed as a percentage of the average annual rainfall) applied to each watershed before and after treatment to evaluate the effects of brush management. During the post-treatment period, the percent average annual unit runoff in the reference watershed was similar to that in the treatment watershed, however, the difference in percentages of average annual evapotranspiration and potential groundwater recharge were more appreciable between the reference and treatment watersheds than during the pre-treatment period. Using graphical comparisons, no notable differences in major ion or nutrient concentrations were found between samples collected at the reference watershed (site 1C) and treatment watershed (site 2C) during pre- and post-treatment periods. Suspended-sediment loads were calculated from samples collected at sites 1C and 2T. The relation between suspended-sediment loads and streamflow calculated from samples collected from sites 1C and 2T did not exhibit a statistically significant difference during the pre-treatment period, whereas during the post-treatment period, relation between suspended-sediment loads and streamflow did exhibit a statistically significant difference. The suspended-sediment load to streamflow relations indicate that for the same streamflow, the suspended-sediment loads calculated from site 2T were generally less than suspended-sediment loads calculated from site 1C during the post-treatment period.

Mass balance modelling of contaminants in river basins: a flexible matrix approach.

PubMed

Warren, Christopher; Mackay, Don; Whelan, Mick; Fox, Kay

2005-12-01

A novel and flexible approach is described for simulating the behaviour of chemicals in river basins. A number (n) of river reaches are defined and their connectivity is described by entries in an n x n matrix. Changes in segmentation can be readily accommodated by altering the matrix entries, without the need for model revision. Two models are described. The simpler QMX-R model only considers advection and an overall loss due to the combined processes of volatilization, net transfer to sediment and degradation. The rate constant for the overall loss is derived from fugacity calculations for a single segment system. The more rigorous QMX-F model performs fugacity calculations for each segment and explicitly includes the processes of advection, evaporation, water-sediment exchange and degradation in both water and sediment. In this way chemical exposure in all compartments (including equilibrium concentrations in biota) can be estimated. Both models are designed to serve as intermediate-complexity exposure assessment tools for river basins with relatively low data requirements. By considering the spatially explicit nature of emission sources and the changes in concentration which occur with transport in the channel system, the approach offers significant advantages over simple one-segment simulations while being more readily applicable than more sophisticated, highly segmented, GIS-based models.

Are catchment-wide erosion rates really "Catchment-Wide"? Effects of grain size on erosion rates determined from 10Be

NASA Astrophysics Data System (ADS)

Reitz, M. A.; Seeber, L.; Schaefer, J. M.; Ferguson, E. K.

2012-12-01

Early studies pioneering the method for catchment wide erosion rates by measuring 10Be in alluvial sediment were taken at river mouths and used the sand size grain fraction from the riverbeds in order to average upstream erosion rates and measure erosion patterns. Finer particles (<0.0625 mm) were excluded to reduce the possibility of a wind-blown component of sediment and coarser particles (>2 mm) were excluded to better approximate erosion from the entire upstream catchment area (coarse grains are generally found near the source). Now that the sensitivity of 10Be measurements is rapidly increasing, we can precisely measure erosion rates from rivers eroding active tectonic regions. These active regions create higher energy drainage systems that erode faster and carry coarser sediment. In these settings, does the sand-sized fraction fully capture the average erosion of the upstream drainage area? Or does a different grain size fraction provide a more accurate measure of upstream erosion? During a study of the Neto River in Calabria, southern Italy, we took 8 samples along the length of the river, focusing on collecting samples just below confluences with major tributaries, in order to use the high-resolution erosion rate data to constrain tectonic motion. The samples we measured were sieved to either a 0.125 mm - 0.710 mm fraction or the 0.125 mm - 4 mm fraction (depending on how much of the former was available). After measuring these 8 samples for 10Be and determining erosion rates, we used the approach by Granger et al. [1996] to calculate the subcatchment erosion rates between each sample point. In the subcatchments of the river where we used grain sizes up to 4 mm, we measured very low 10Be concentrations (corresponding to high erosion rates) and calculated nonsensical subcatchment erosion rates (i.e. negative rates). We, therefore, hypothesize that the coarser grain sizes we included are preferentially sampling a smaller upstream area, and not the entire upstream catchment, which is assumed when measurements are based solely on the sand sized fraction. To test this hypothesis, we used samples with a variety of grain sizes from the Shillong Plateau. We sieved 5 samples into three grain size fractions: 0.125 mm - 710 mm, 710 mm - 4 mm, and >4 mm and measured 10Be concentrations in each fraction. Although there is some variation in the grain size fraction that yields the highest erosion rate, generally, the coarser grain size fractions have higher erosion rates. More significant are the results when calculating the subcatchment erosion rates, which suggest that even medium sized grains (710 mm - 4 mm) are sampling an area smaller than the entire upstream area; this finding is consistent with the nonsensical results from the Neto River study. This result has numerous implications for the interpretations of 10Be erosion rates: most importantly, an alluvial sample may not be averaging the entire upstream area, even when using the sand size fraction - resulting erosion rates more pertinent for that sample point rather than the entire catchment.

Modeling chemical accumulation in sediment of small waterbodies accounting for sediment transport and water-sediment exchange processes over long periods.

PubMed

Patterson, David Albert; Strehmel, Alexander; Erzgräber, Beate; Hammel, Klaus

2017-12-01

In a recent scientific opinion of the European Food Safety Authority it is argued that the accumulation of plant protection products in sediments over long time periods may be an environmentally significant process. Therefore, the European Food Safety Authority proposed a calculation to account for plant protection product accumulation. This calculation, however, considers plant protection product degradation within sediment as the only dissipation route, and does not account for sediment dynamics or back-diffusion into the water column. The hydraulic model Hydrologic Engineering Center-River Analysis System (HEC-RAS; US Army Corps of Engineers) was parameterized to assess sediment transport and deposition dynamics within the FOrum for Co-ordination of pesticide fate models and their USe (FOCUS) scenarios in simulations spanning 20 yr. The results show that only 10 to 50% of incoming sediment would be deposited. The remaining portion of sediment particles is transported across the downstream boundary. For a generic plant protection product substance this resulted in deposition of only 20 to 50% of incoming plant protection product substance. In a separate analysis, the FOCUS TOXSWA model was utilized to examine the relative importance of degradation versus back-diffusion as loss processes from the sediment compartment for a diverse range of generic plant protection products. In simulations spanning 20 yr, it was shown that back-diffusion was generally the dominant dissipation process. The results of the present study show that sediment dynamics and back-diffusion should be considered when calculating long-term plant protection product accumulation in sediment. Neglecting these may lead to a systematic overestimation of accumulation. Environ Toxicol Chem 2017;36:3223-3231. © 2017 SETAC. © 2017 SETAC.

Preservation efficiencies and accumulation rates for biogenic silica and organic C, N, and P in high-latitude sediments: The Ross Sea

NASA Astrophysics Data System (ADS)

Demaster, David J.; Ragueneau, Olivier; Nittrouer, Charles A.

1996-08-01

Rates of biogenic sediment accumulation (biogenic silica and organic C, N, and P) and pore water flux have been established for a variety of depositional environments in the Ross Sea. On the basis of 14C measurements in kasten cores, sediment accumulation rates ranged from 250 cm kyr-1 in the coastal basin of Granite Harbor to 1-2 cm kyr-1 in the shelf and slope environments of the northern and eastern Ross Sea. Burial of biogenic material was most rapid in the southwestern Ross Sea, where biogenic silica accumulation rates ranged from 2 to 31 g cm-2 kyr-1 and organic carbon accumulation rates ranged from 0.05 to 1.4 g cm-2 kyr-1. In the northern and eastern Ross Sea, biogenic silica and organic carbon accumulation rates typically equaled 0.02-0.03 g SiO2 cm-2 kyr-1 and 0.002-0.004 g C cm-2 kyr-1. Flux core measurements were used to estimate seabed regeneration rates for biogenic silica, organic carbon, and phosphorus. Pore water fluxes, in general, showed much less variability across the Ross Sea than did the biogenic accumulation rates. Pore water silicate fluxes in the study area ranged from 0.6 to 5.3 g SiO2 cm-2 kyr-1, whereas carbon fluxes ranged from 0.1 to 1.2 g C cm-2 kyr-1 and phosphate fluxes varied from -0.006 to 0.012 g P cm-2 kyr-1. Seabed preservation efficiencies were calculated for biogenic silica, organic carbon, and phosphorus by combining the solid-phase and pore water data. The seabed preservation efficiencies for biogenic silica (1-86%) were greater than for organic carbon (1-71%) at all nine stations examined. The preferential preservation of biogenic silica relative to organic carbon also was apparent in Ross Sea sediments because the biogenic silica/organic carbon ratio in the material buried in the seabed generally was 2 times greater than the ratio in sediment particles arriving at the sediment-water interface. Sediment accumulation rate correlated strongly with both the biogenic silica and the organic carbon preservation efficiency data. P preservation efficiencies remained relatively high (24-65%) even when the accumulation rates were low (1-2 cm kyr-1) because of the near-zero phosphate fluxes out of the seabed. Of the total P in the seabed (0.04-0.09 wt. %), approximately 25% existed in the form of organic P. The total amount of biogenic silica accumulating on the Ross Sea shelf is ˜2.3 × 1012 g SiO2 yr-1, which is approximately an order of magnitude less than the Ledford-Hoffman et al. [1986] estimate that was based on 210Pb chronologies. Biogenic silica accumulation rates in the southern, central, and western Ross Sea increased during the mid and late Holocene, reaching their maximum values during the past 500 to 1000 years.

Development of a numerical model for calculating exposure to toxic and nontoxic stressors in the water column and sediment from drilling discharges.

PubMed

Rye, Henrik; Reed, Mark; Frost, Tone Karin; Smit, Mathijs G D; Durgut, Ismail; Johansen, Øistein; Ditlevsen, May Kristin

2008-04-01

Drilling discharges are complex mixtures of chemical components and particles which might lead to toxic and nontoxic stress in the environment. In order to be able to evaluate the potential environmental consequences of such discharges in the water column and in sediments, a numerical model was developed. The model includes water column stratification, ocean currents and turbulence, natural burial, bioturbation, and biodegradation of organic matter in the sediment. Accounting for these processes, the fate of the discharge is modeled for the water column, including near-field mixing and plume motion, far-field mixing, and transport. The fate of the discharge is also modeled for the sediment, including sea floor deposition, and mixing due to bioturbation. Formulas are provided for the calculation of suspended matter and chemical concentrations in the water column, and burial, change in grain size, oxygen depletion, and chemical concentrations in the sediment. The model is fully 3-dimensional and time dependent. It uses a Lagrangian approach for the water column based on moving particles that represent the properties of the release and an Eulerian approach for the sediment based on calculation of the properties of matter in a grid. The model will be used to calculate the environmental risk, both in the water column and in sediments, from drilling discharges. It can serve as a tool to define risk mitigating measures, and as such it provides guidance towards the "zero harm" goal.

Quaternary fans and terraces in the Khumbu Himal south of Mount Everest: their characteristics, age and formation

USGS Publications Warehouse

Barnard, P.L.; Owen, L.A.; Finkel, R.C.

2006-01-01

Large fans and terraces are frequent in the Khumbu Himal within the high Himalayan valleys south of Mt. Everest. These features are composed of massive matrix- and clast-supported diamicts that were formed from both hyperconcentrated flows and coarse-grained debris flows. Cosmogenic radionuclide (CRN) exposure ages for boulders on fans and terraces indicate that periods of fan and terrace formation occurred at c. 16, c. 12, c. 8, c. 4 and c. 1.5 ka, and are broadly coincident with the timing of glaciation in the region. The dating precision is insufficient to resolve whether the surfaces formed before, during or after the correlated glacial advance. However, the sedimentology, and morphostratigraphic and geomorphological relationships suggest that fan and terrace sedimentation in this part of the Himalaya primarily occurs during glacier retreat and is thus paraglacial in origin. Furthermore, modern glacial-lake outburst floods and their associated deposits are common in the Khumbu Himal as the result of glacial retreat during historical times. We therefore suggest that Late Quaternary and Holocene fan and terrace formation and sediment transfer are probably linked to temporal changes in discharge and sediment load caused by glacier oscillations responding to climate change. The timing of major sedimentation events in this region can be correlated with fans and terraces in other parts of the Himalaya, suggesting that major sedimentation throughout the Himalaya is synchronous and tied to regional climatic oscillations. Bedrock incision rates calculated from strath terrace ages average c. 3.9 mm a−1, suggesting that the overall rate of incision is set by regional uplift.

Effects of land disturbance on runoff and sediment yield after natural rainfall events in southwestern China.

PubMed

Guo, Xiaomeng; Li, Tianyang; He, Binghui; He, Xiaorong; Yao, Yun

2017-04-01

Severe soil erosion occurs in southwestern China owing to the large expanses of urbanization and sloping land. This field monitoring study was conducted to record the rainfall events, runoff, and sediment yield in 20-, 40-, and 60-m plots under conditions of artificial disturbance or natural restoration in the purple soil area of southwestern China. The study took place during the rainy season, and the plots were situated on a 15° slope. The results showed that rainstorms and heavy rainstorms generated runoff and sediment yield. Rainfall intensity had a significantly positive power relationship with runoff rate and sediment yield rate in artificially disturbed plots but not in naturally restored plots. Plot length had a significant effect on runoff rate under artificial disturbance but not natural restoration. Within the same land disturbance category, there was no significant effect of plot length on sediment yield rate but there was a significant effect on sediment concentration. Overall, runoff rate, sediment yield rate, and sediment concentration showed remarkable effects of land disturbance across all plot lengths: naturally restored plots had 62.8-77.5% less runoff, 95.1-96.3% less sediment yield, and 63.1-73.5% lower sediment concentration than artificially disturbed plots. The relationship between runoff rate and sediment rate under the different land disturbances could be described by an exponential function. The results not only demonstrate the effectiveness of natural restoration for controlling runoff and sediment yield but also provide useful information for the design of field studies, taking into consideration the complexity of terrestrial systems.

Hydrologic Controls on Sediment Retention in a Diversion-Fed Coastal Wetland

NASA Astrophysics Data System (ADS)

Keogh, M.; Kolker, A.; Snedden, G.; Renfro, A. A.

2017-12-01

The morphodynamics of river-dominated deltas are largely controlled by the supply and retention of sediment within deltaic wetlands and the rate of relative sea-level rise. Yet, sediment budgets for deltas are often poorly constrained. In the Mississippi River Delta, a system rapidly losing land to natural and anthropogenic causes, restoration efforts seek to build new land through the use of river diversions. At Davis Pond Freshwater Diversion, a new crevasse splay has emerged since construction was completed in 2002. Here, we use beryllium-7 (7Be) activity in sediment cores and USGS measurements of discharge and turbidity to calculate seasonal sediment input, deposition, and retention within the Davis Pond receiving basin. In winter/spring 2015, Davis Pond received 104,000 metric tons of sediment, 43.8% of which was retained within the basin. During this time, mean flow velocity was 0.21 m/s and turbidity was 56 formazin nephelometric units (FNU). In summer/fall 2015, Davis Pond received 35,100 metric tons of sediment, 82.1% of which was retained. Mean flow velocity in summer/fall was 0.10 m/s and turbidity was 55 FNU. The increase in sediment retention from winter/spring 2015 to summer/fall 2015 is likely due to the corresponding drop in water flow velocity, which allowed more sediment to settle out of suspension. Although high water discharge increases sediment input and deposition, increased turbulence associated with higher current velocity may increase sediment throughput and decrease the percent of sediments retained in the system. Sediment retention in Davis Pond is on the high end of the range seen in deltaic wetlands, likely due to the enclosed geometry of the receiving basin. Future diversion design and operation should target moderate water discharge and flow velocities in order to jointly maximize sediment deposition and retention and provide optimal conditions for delta growth.

Environmental factors controlling spatial variation in sediment yield in a central Andean mountain area

NASA Astrophysics Data System (ADS)

Molina, Armando; Govers, Gerard; Poesen, Jean; Van Hemelryck, Hendrik; De Bièvre, Bert; Vanacker, Veerle

2008-06-01

A large spatial variability in sediment yield was observed from small streams in the Ecuadorian Andes. The objective of this study was to analyze the environmental factors controlling these variations in sediment yield in the Paute basin, Ecuador. Sediment yield data were calculated based on sediment volumes accumulated behind checkdams for 37 small catchments. Mean annual specific sediment yield (SSY) shows a large spatial variability and ranges between 26 and 15,100 Mg km - 2 year - 1 . Mean vegetation cover (C, fraction) in the catchment, i.e. the plant cover at or near the surface, exerts a first order control on sediment yield. The fractional vegetation cover alone explains 57% of the observed variance in ln(SSY). The negative exponential relation (SSY = a × e- b C) which was found between vegetation cover and sediment yield at the catchment scale (10 3-10 9 m 2), is very similar to the equations derived from splash, interrill and rill erosion experiments at the plot scale (1-10 3 m 2). This affirms the general character of an exponential decrease of sediment yield with increasing vegetation cover at a wide range of spatial scales, provided the distribution of cover can be considered to be essentially random. Lithology also significantly affects the sediment yield, and explains an additional 23% of the observed variance in ln(SSY). Based on these two catchment parameters, a multiple regression model was built. This empirical regression model already explains more than 75% of the total variance in the mean annual sediment yield. These results highlight the large potential of revegetation programs for controlling sediment yield. They show that a slight increase in the overall fractional vegetation cover of degraded land is likely to have a large effect on sediment production and delivery. Moreover, they point to the importance of detailed surface vegetation data for predicting and modeling sediment production rates.

Energy and power limits for microbial activity

NASA Astrophysics Data System (ADS)

LaRowe, D.; Amend, J.

2014-12-01

The goal of this presentation is to describe a quantitative framework for determining how energy limits microbial activity, biomass and, ultimately, biogeochemical processes. Although this model can be applied to any environment, its utility is demonstrated in marine sediments, which are an attractive test habitat because they encompass a broad spectrum of energy levels, varying amounts of biomass and are ubiquitous. The potential number of active microbial cells in Arkonas Basin (Baltic Sea) sediments are estimated as a function of depth by quantifying the amount of energy that is available to them and the rate at which it is supplied: power. The amount of power supplied per cubic centimeter of sediment is determined by calculating the Gibbs energy of fermentation and sulfate reduction in combination with the rate of particulate organic carbon, POC, degradation. The Reactive Continuum Model (Boudreau and Ruddick, 1991), RCM, is used to determine the rate at which POC is made available for microbial consumption. The RCM represents POC as containing a range of different types of organic compounds whose ability to be consumed by microorganisms varies as a function of the age of the sediment and on the distribution of compound types that were initially deposited. The sediment age model and RCM parameters determined by (Mogollon et al., 2012) are used. The power available for fermentation and sulfate reduction coupled to H2 and acetate oxidation varies from 10-8 W cm-3 at the sediment water interface to between 10-11 - 10-12 W cm-3 at 3.5 meters below the seafloor, mbsf. Using values of maintenance powers for each of these catabolic activities taken from the literature, the total number of active cells in these sediments similarly decreases from just less than 108 cell cm-3 at the SWI to 4.6 x 104 cells cm-3 at 3.5 mbsf. The number of moles of POC decreases from 2.6 x 10-5 to 9.5 x 10-6, also becoming more recalcitrant with depth. Boudreau, B. P. and Ruddick, B. R. (1991) On a reactive continuum representation of organic matter diagenesis. Amer. J. Sci. 291, 507-538. Mogollon, J. M., Dale, A. W., Fossing, H. and Regnier, P. (2012) Timescales for the development of methanogenesis and free gas layers in recently-deposited sediments of Arkona Bason (Baltic Sea). Biogeosciences 9, 1915-1933.

Temporal and spatial patterns of sedimentation within the batture lands of the middle Mississippi River, USA

NASA Astrophysics Data System (ADS)

Remo, Jonathan W. F.; Ryherd, Julia; Ruffner, Charles M.; Therrell, Matthew D.

2018-05-01

Sediment deposition and storage are important functions of batture lands (the land between the channel's low-water elevation and the flood mitigation levee). However, sedimentation processes within these areas are not fully understood. In this paper, we explore the spatiotemporal patterns, rates, and volume of sedimentation within the batture lands along the middle Mississippi River (MMR; between the confluence of the Missouri and Ohio rivers) using three approaches: (1) comparison of historical to modern elevation data in order to estimate long-term (>100 yr) sedimentation rates; (2) estimation of medium- to short-term (<50 yr) sedimentation rates using dendrogeomorphological methods; and (3) geomorphic change detection (GCD) software to estimate short-term sedimentation rates ( 12 yr), spatial patterns of deposition, and volumes of geomorphic change within the batture lands. Comparison of long- to short-term sedimentation rates suggests up to a 300% increase in batture land sedimentation rates (from 6.2 to 25.4 mm yr-1) despite a substantial decrease in the MMR's suspended-sediment load (>70%) attributed largely to sediment trapping by dams during the second half of the twentieth century. The increase in MMR batture land sedimentation rates are attributed to at least two potential mechanisms: (1) the above average frequency and duration of low-magnitude floods (>2-yr and ≤5-yr flood) during the short-term assessment periods which allowed for more suspended sediment to be deposited within the batture lands; and (2) the construction of levees that substantially reduced the floodplain area ( 75%) available for storage of overbank deposits increasing the vertical accumulation and consequently the detectability of a given volume of sediment. The GCD estimated batture land sediment volumes were 9.0% of the suspended load at St. Louis. This substantial storage of sediment ( 8.5 Mt yr-1) along the MMR suggests batture lands are an important sink for suspended sediments.

Authigenic molybdenum formation in marine sediments: A link to pore water sulfide in the Santa Barbara Basin

USGS Publications Warehouse

Zheng, Yen; Anderson, Robert F.; VanGeen, A.; Kuwabara, J.

2000-01-01

Pore water and sediment Mo concentrations were measured in a suite of multicores collected at four sites along the northeastern flank of the Santa Barbara Basin to examine the connection between authigenic Mo formation and pore water sulfide concentration. Only at the deepest site (580 m), where pore water sulfide concentrations rise to >0.1 ??M right below the sediment water interface, was there active authigenic Mo formation. At shallower sites (550,430, and 340 m), where pore water sulfide concentrations were consistently <0.05 ??M, Mo precipitation was not occuring at the time of sampling. A sulfide concentration of ???0.1 ??M appears to be a threshold for the onset of Mo-Fe-S co-precipitation. A second threshold sulfide concentration of ???100 ??M is required for Mo precipitation without Fe, possibly as Mo-S or as particle-bound Mo. Mass budgets for Mo were constructed by combining pore water and sediment results for Mo with analyses of sediment trap material from Santa Barbara Basin as well as sediment accumulation rates derived from 210Pb. The calculations show that most of the authigenic Mo in the sediment at the deepest site is supplied by diffusion from overlying bottom waters. There is, however, a non-lithogenic particulate Mo associated with sinking particles that contributes ???15% to the total authigenic Mo accumulation. Analysis of sediment trap samples and supernant brine solutions indicates the presence of non-lithogenic particulate Mo, a large fraction of which is easily remobilized and, perhaps, associated with Mn-oxides. Our observations show that even with the very high flux of organic carbon reaching the sediment of Santa Barbara Basin, active formation of sedimentary authigenic Mo requires a bottom water oxygen concentration below 3 ??M. However, small but measurable rates of authigenic Mo accumulation were observed at sites where bottom water oxygen ranged between 5 and 23 ??M, indicating that the formation of authigenic Mo occured in the recent past, but not at the time of sampling. Copyright ?? 2000 Elsevier Science Ltd.

Distribution of basic sediments (bedload transport) on changes in coastal coastline Donggala, Central Sulawesi Province, Indonesia

NASA Astrophysics Data System (ADS)

Amiruddin

2018-03-01

This study entitled "Distribution of Bedload Transport Against Coastline Changes in Donggala Coast", the formulation of the problem (1) how much of the estimated bedload transport in Donggala Bodies; (2) where were the location of erosion and sedimentation strong point based on the estimation of bed load transport; (3) the extent to which the prediction of shoreline change rate of transport of sediments in coastal areas Donggala. This study aims to: (1) the calculation of estimated bed load transport in Donggala waters; (2) determining the location of the point of erosion and sedimentation strong basis of estimated bedload transport; (3) the prediction of shoreline change rate of transport of sediments in coastal areas Donggala.The survey method used in this research to collect primary data include: (1) decision point waypoint coordinates of each location of measurement; (2) measurement of height, period and direction of the waves; (3) a large measurement of sediment transport; (4) The angle measurement coastline, angle of attack and wave direction, and secondary data include: (1) information from the public; (2) the physical condition data field. The results showed that: (1) general estimate sediment transport base in each location data collection is varied. This is due to the different points of the coastline as well as the angle of attack of the shoreline waters broke Donggala; (2) strong abrasion at the study site occurs at the point Ts4 (622.75 m3/yr) and TS11 (755.25 m3/yr) located in the Village Tosale and point Tw7 and Tw17 (649.25 m3/yr) in Village of Towale. As for the strong sedimentation occurs at the point Ts3 (450.50 m3/yr) located in the Village Tosale and Tg3 point (357.75 m3/yr) located in the Village Tolonggano; (3) of the predicted outcome coastline changes based on the input data estimate sediment transport, beaches and waves parameters is seen that the changes in the location prophyl coastline tends toward research into or undergo a process of abrasion.

Estimating sedimentation rates and sources in a partially urbanized catchment using caesium-137

NASA Astrophysics Data System (ADS)

Ormerod, L. M.

1998-06-01

While there has been increased interest in determining sedimentation rates and sources in agricultural and forested catchments in recent years, there have been few studies dealing with urbanized catchments. A study of sedimentation rates and sources within channel and floodplain deposits of a partially urbanized catchment has been undertaken using the 137Cs technique. Results for sedimentation rates showed no particular downstream pattern. This may be partially explained by underestimation of sedimentation rates at some sites by failure to sample the full 137Cs profile, floodplain erosion and deliberate removal of sediment. Evidence of lateral increases in net sedimentation rates with distance from the channel may be explained by increased floodplain erosion at sites closer to the channel and floodplain formation by lateral deposition. Potential sediment sources for the catchment were considered to be forest topsoil, subsurface material and sediments derived from urban areas, which were found to be predominantly subsurface material. Tracing techniques showed an increase in subsurface material for downstream sites, confirming expectations that subsurface material would increase in the downstream direction in response to the direct and indirect effects of urbanization.

The rare earth element geochemistry on surface sediments, shallow cores and lithological units of Lake Acıgöl basin, Denizli, Turkey

NASA Astrophysics Data System (ADS)

Budakoglu, Murat; Abdelnasser, Amr; Karaman, Muhittin; Kumral, Mustafa

2015-11-01

The sediments in Lake Acıgöl, located in SW Anatolia, Turkey, were formed under tectono-sedimentary events. REE geochemical investigations of the Lake Acıgöl sediments, from surface and shallow core sediments at different depths (0-10 cm, 10-20 cm and 20-30 cm) are presented to clarify the characteristics of REE and the nature of source rocks in the lake sediments' and to deduce their paleoenvironmental proxies. The chondrite-normalized REE patterns of these sediments are shown as light enrichment in LREE and flat HREE with a negative Eu anomaly that is close to the continental collision basin (CCB) in its profile; this is not comparable with PAAS and UCC. Inorganic detrital materials control the REE characteristics of the Lake Acıgöl sediments and these sediments were accumulated in oxic and dysoxic depositional conditions and/or at passive margins derived from oceanic island arc rocks. They were affected by low chemical weathering, either at the original source or during transport, before deposition under arid or subtropical humid climatic conditions. In addition, we used GIS techniques (such as Inverse Distance Weighted (IDW) and Geographically Weighted Regression (GWR)) to investigate the spatial interpolation and spatial correlation of the REEs from the lake surface sediments in Lake Acıgöl and its surrounding lithological units. GIS techniques showed that the lithological units (e.g., Hayrettin Formation) north of Lake Acıgöl have high REE contents; however, Eu/Eu∗ values were higher in some lake surface sediments than in lithological units, and that refers to a negative Eu-anomaly. Therefore, Lake Acıgöl sediments are derived from the weathered products, mainly from local, highly basic bedrock around the lake from the Archean crust. The chronology of Lake Acıgöl sediment was conducted using the Constant Rate of Supply (CRS) model. Using the CRS methods for the calculation of sedimentation rate, we obtained a 0.012 g/cm2/year value which is an average value for the first 20 cm depth of this lake. The core activity profiles of 210Pb and 137Cs were measured to estimate the age of the sediments; we observed activities of 8.08 ± 5.5 Bq/kg for 210Pb and 0.86 ± 0.6 Bq/kg for 137Cs.

Sulfate reduction and oxic respiration in marine sediments: implications for organic carbon preservation in euxinic environments

NASA Technical Reports Server (NTRS)

Canfield, D. E.; DeVincenzi, D. L. (Principal Investigator)

1989-01-01

Compilations have been made of sulfate reduction rates and oxic respiration rates over the entire range of marine sedimentation rates, and sedimentary environments, including several euxinic sites. These data show, consistent with the findings of Jorgensen (1982, Nature, 296, 643-645), that sulfate reduction and oxic respiration oxidize equal amounts of organic carbon in nearshore sediments. As sedimentation rates decrease, oxic respiration, becomes progressively more important, and in deep-sea sediments 100-1000 times more organic carbon is oxidized by oxic respiration than by sulfate reduction. By contrast, nearly as much organic carbon is oxidized by sulfate reduction in euxinic sediments as is oxidized by the sum of sulfate reduction and oxic respiration in normal marine sediments of similar deposition rate. This observation appears at odds with the enhanced preservation of organic carbon observed in euxinic sediments. However, only small reductions in (depth-integrated) organic carbon decomposition rates (compared to normal marine) are required to give both high organic carbon concentrations and enhanced carbon preservation in euxinic sediments. Lower rates of organic carbon decomposition (if only by subtle amounts) are explained by the diminished ability of anaerobic bacteria to oxidize the full suite of sedimentary organic compounds.

Sedimentation within the batture lands of the middle Mississippi River, USA

NASA Astrophysics Data System (ADS)

Remo, J. W.; Ryherd, J. K.

2017-12-01

The suspended sediment load of the Mississippi River has continued to decline after the construction of several hundred large dams within the basin during the mid-20th century. Previous investigators have attributed the post-dam decline in suspended sediment loads to improvements in soil conservation practices and dredging. However, the role batture lands (areas between the river channel and levee) play as potential sinks for suspend sediments has largely been overlooked. In this study, we explored the rates and volume of sedimentation within the batture lands along the middle Mississippi River (MMR; between the confluence of the Missouri and Ohio Rivers). We assessed sedimentation rates using three approaches: 1) comparison of historical to modern elevation data in order to estimate long-term (>100-years) sedimentation rates; 2) estimation of medium- to short-term (<50-years) sedimentation rates using dendrogeomorphological methods; and 3) geomorphic change detection software (GCDS) to estimate short-term sedimentation rates (12 years). We also used GCDS to estimate the volume of sedimentation within the batture lands between 1998 and 2011. Comparison of long- to short-term sedimentation rates suggests up to a 400% increase in batture land sedimentation rates (from 6.2 to 25.4 mm y-1) despite a substantial decrease in the suspended sediment load (>70%). The increase in MMR batture land sedimentation rates are attributed to three mechanisms: 1) the above average frequency and duration of low-magnitude floods (≤5-year flood) during the short-term assessment periods, which allowed for more suspended sediment to be transported into and deposited within, the batture lands; 2) the construction of levees which substantially reduced ( 75%) floodplain areas available for storage of overbank deposits; and 3) river engineering which has reduced bank erosion allowing sediment to be stored for longer periods of time in the batture lands. The estimated batture land sediment volumes were 5.0% of the suspended load at St. Louis. This substantial storage of sediment ( 9.0 Mt y-1) along the MMR suggests batture lands are an important sink for suspended sediments. Deposition within these areas is contributing to the decrease in the suspended sediment load along this and likely other segments of the Mississippi River.

Sediment characteristics and sedimentation rates in Lake Michie, Durham County, North Carolina, 1990-92

USGS Publications Warehouse

Weaver, J.C.

1994-01-01

A reservoir sedimentation study was conducted at 508-acre Lake Michie, a municipal water-supply reservoir in northeastern Durham County, North Carolina, during 1990-92. The effects of sedimentation in Lake Michie were investigated, and current and historical rates of sedimentation were evaluated. Particle-size distributions of lake-bottom sediment indicate that, overall, Lake Michie is rich in silt and clay. Nearly all sand is deposited in the upstream region of the lake, and its percentage in the sediment decreases to less than 2 percent in the lower half of the lake. The average specific weight of lake-bottom sediment in Lake Michie is 73.6 pounds per cubic foot. The dry-weight percentage of total organic carbon in lake-bottom sediment ranges from 1.1 to 3.8 percent. Corresponding carbon-nitrogen ratios range form 8.6 to 17.6. Correlation of the total organic carbon percentages with carbon-nitrogen ratios indicates that plant and leaf debris are the primary sources of organic material in Lake Michie. Sedimentation rates were computed using comparisons of bathymetric volumes. Comparing the current and previous bathymetric volumes, the net amount of sediment deposited (trapped) in Lake Michie during 1926-92 is estimated to be about 2,541 acre-feet or slightly more than 20 percent of the original storage volume computed in 1935. Currently (1992), the average sedimentation rate is 38 acre-feet per year, down from 45.1 acre-feet per year in 1935. To confirm the evidence that sedimentation rates have decreased at Lake Michie since its construction in 1926, sediment accretion rates were computed using radionuclide profiles of lake-bottom sediment. Sediment accretion rates estimated from radiochemical analyses of Cesium-137 and lead-210 and radionuclides in the lake-bottom sediment indicate that rates were higher in the lake?s early years prior to 1962. Estimated suspended-sediment yields for inflow and outflow sites during 1983-91 indicate a suspended-sediment trap efficiency of 89 percent. An overall trap efficiency for the period of 1983-91 was computed using the capacity-inflow ratio. The use of this ratio indicates that the trap efficiency for Lake Michie is 85 percent. However, the suspended-sediment trap efficiency indicates that the actual overall trap efficiency for Lake Michie was probably greater than 89 percent during this period.

Sediment dynamics and their potential influence on insular-slope mesophotic coral ecosystems

NASA Astrophysics Data System (ADS)

Sherman, C.; Schmidt, W.; Appeldoorn, R.; Hutchinson, Y.; Ruiz, H.; Nemeth, M.; Bejarano, I.; Motta, J. J. Cruz; Xu, H.

2016-10-01

Although sediment dynamics exert a fundamental control on the character and distribution of reefs, data on sediment dynamics in mesophotic systems are scarce. In this study, sediment traps and benthic photo-transects were used to document spatial and temporal patterns of suspended-sediment and bed-load dynamics at two geomorphically distinct mesophotic coral ecosystems (MCEs) on the upper insular slope of southwest Puerto Rico. Trap accumulation rates of suspended sediment were relatively low and spatiotemporally uniform, averaging <1 mg cm-2 d-1 and never exceeding 3 mg cm-2 d-1 over the sampled period. In contrast, trap accumulation rates of downslope bed-load movement were orders of magnitude higher than suspended-sediment accumulation rates and highly variable, by orders of magnitude, both spatially and temporally. Percent sand cover within photo-transects varied over time from 10% to more than 40% providing further evidence of downslope sediment movement. In general, the more exposed, lower gradient site had higher rates of downslope sediment movement, higher sand cover and lower coral cover than the more sheltered and steep site that exhibited lower rates of downslope sediment movement, lower sand cover and higher coral cover. In most cases, trap accumulation rates of suspended sediment and bed load varied together and peaks in trap accumulation rates correspond to peaks in SWAN-modeled wave-orbital velocities, suggesting that surface waves may influence sediment dynamics even in mesophotic settings. Though variable, off-shelf transport of sediment is a continuous process occurring even during non-storm conditions. Continuous downslope sediment movement in conjunction with degree of exposure to prevailing seas and slope geomorphology are proposed to exert an important influence on the character and distribution of insular-slope MCEs.

Dispersal of Sediment in the Western Adriatic during Energetic Wintertime Forcing

NASA Astrophysics Data System (ADS)

Harris, C. K.; Sherwood, C. R.; Mullenbach, B. L.; Pullen, J. D.

2003-12-01

EuroSTRATAFORM aims to relate sediment delivery and reworking to seabed morphology and stratigraphy through observations and modeling of water column transport. The Po River dominates buoyancy and sediment input into the Adriatic Sea, but small Apeninne rivers (the Chienti, Pescara, etc.) may produce locally important signals. Sedimentation is influenced by fluvial supply, resuspension by waves and currents, and transport by oceanographic currents forced by winds and buoyancy. Transport is likely highest during times of energetic forcing; including Bora events with northeasterly winds and Sirocco events with southeasterly winds. It is difficult, from field measurements alone, to characterize dispersal and convergence patterns over the relevant spatial scales. We applied a three-dimensional hydrodynamic model that includes fluvial delivery, transport, resuspension, and deposition of sediment to quantify sediment dispersal with a 2-km resolution over the entire Adriatic. Circulation calculations were driven by spatially- and temporally-varying wind fields for the Fall / Winter of 2002 / 2003 and realistic Po and Apennine river discharges. Waves were hindcast with the SWAN model. Dispersion of both resuspended and river-derived sediment was estimated for periods that contained intense Bora and Sirocco winds. Predicted sediment dispersal rates and patterns are sensitive to forcing winds, buoyancy flux, and wave patterns. Higher sediment flux was predicted during Bora conditions than during Sirocco conditions. Sirocco winds weaken the Western Adriatic Coastal Current (WACC), and because they tend to concentrate over the Eastern Adriatic, they often fail to create especially energetic waves in the Western Adriatic. Bora wind conditions, on the other hand, intensify the WACC and can build high wave energies over the northwestern Adriatic. Most of the sediment transport occurs during Bora, with a net southward flux. These predictions will be compared to field observations made as part of the EuroSTRATAFORM experiment.

Bioavailability and bioaccumulation of heavy metals of several soils and sediments (from industrialized urban areas) for Eisenia fetida.

PubMed

Coelho, C; Foret, C; Bazin, C; Leduc, L; Hammada, M; Inácio, M; Bedell, J P

2018-09-01

Soils and sediments are susceptible to anthropogenic contamination with Metallic Trace Elements (MTEs) and it can present some risks to ecosystems and human health. The levels of Cd, Cu, Fe, Ni, Pb and Zn were assessed in soils (C, G, K, L) from Estarreja (Portugal) and sediments from a stormwater basin in Lyon (DJG), a harbour (LDB) and a Rhône river site (TRS) (France). An ecotoxicological study was performed with Eisenia fetida (E. fetida) to infer about potential transfer risks to the soil invertebrates. To assess risks associated with MTEs contamination, it is important to know their total concentrations, fractionation and the potential available fractions. CaCl 2 , DTPA and NaOAc extractions were performed to assess the extractable and available MTEs fractions. The studied sediments were much more contaminated than the soils for all the MTEs analysed. The trace elements fraction linked with DTPA extraction shows higher values when compared with the NaOAc and the CaCl 2 pools. Low mortality effects were recorded in the tests with E. fetida. The MTEs levels in soils and sediments and the concentrations bioaccumulated in adult earthworms contributed to a reduction in the number of juveniles produced. E. fetida adults and juveniles accumulated ETMs as follows: Cd > Cu = Zn > Ni > Pb > Fe. Determined BAFs were mostly lower than 1 with some higher values for Cd, Cu and Zn. Calculated SET and ERITME indexes allowed to classify the samples from the most to the less toxic for E. fetida as: LDB > DJG > L > G > C > K > TRS. Despite this order of toxicity, the earthworms exposed to the sediment TRS presented the lowest reproduction rate. The combination of "chemical" measurements with the calculation of BAFs, but especially SET and ERITME indexes can be a useful tool in risk assessment. Copyright © 2018 Elsevier B.V. All rights reserved.

Assessment of radionuclides and heavy metals in marine sediments along the Upper Gulf of Thailand

NASA Astrophysics Data System (ADS)

Khuntong, S.; Phaophang, C.; Sudprasert, W.

2015-05-01

Due to the Fukushima Daiichi nuclear disaster in 2011 and the development of nuclear power plant in neighboring countries such as Vietnam in the near future, radionuclide assessment in marine sediment during 2010 - 2011 may be useful as background levels for radiation protection in Thailand. Marine sediments (10 samples) were collected approximately 1 km away from the coastline along Chonburi to Pattaya, Chonburi Province. The sediments were ground and sieved through 2-mm test sieve after air drying. Radionuclides were measured with a gamma spectrometer equipped with a well-calibrated HPGe detector. The samples were prepared in the same geometry as the reference material. The optimal counting time was 60,000 - 80,000 s for statistical evaluation and uncertainties. No contamination of 137Cs as an artificial radionuclide was found. Naturally-occurring radionuclides including 238U, 232Th and 40K were found. The mean specific activities of 238U, 232Th and 40K were 44 ± 10, 59 ± 17 and 463 ± 94 Bq/kg in the rainy season (2010); 41 ± 6, 50 ± 9 and 484 ± 83 Bq/kg in the winter (2010), and 39 ± 6, 41 ± 7 and 472 ± 81 Bq/kg in the summer (2011), respectively. The mean specific activities were higher than the values in the UNSCEAR report of 35, 30 and 400 Bq/kg for 238U, 232Th and 40K, respectively. From the measured specific activities, the absorbed dose rate, radium equivalent activity, external hazard index and annual external effective dose rate were calculated in order to assess the health risk. No radiation hazards related to the radioactivity in the sediment were expected. The accumulation of radionuclides varied with the particle size and the organic matter content in the sediment. The accumulation of heavy metals showed similar results to that of the radionuclides in the sediment.

Estimated post-Messinian sediment supply and sedimentation rates on the Ebro continental margin, Spain

USGS Publications Warehouse

Nelson, C.H.

1990-01-01

Because of the extensive data base of seismic profiles, radiometric ages, and stratigraphic time markers such as the subaerial Messinian surface, sedimentation rates and Ebro River sediment discharge can be estimated for different periods and environments of the Ebro continental margin. New values for sediment discharge (i.e., 6.2 versus previous estimates of 2-3.5 million t/yr) for the Holocene highstand are more reliable but remain minimum estimates because a small proportion of Ebro sediment advected to the Balearic Rise and Abyssal Plain cannot be accounted for, especially during lowstands. The general highstand conditions of the Pliocene, which were similar to those of the Holocene, resulted in a low discharge of Ebro River sediment (ca. 6.5 million t/yr) and an even thickness of sediment across the margin that deposited at rates of about 24-40 cm/ky. In contrast, sediment supply increased two-three times during the Pleistocene, the margin prograded rapidly and deposition occurred at rates of 101-165 cm/ky on the outer shelf and slope, but basin floor rates remained anomalously low (21-26 cm/ky) because sediment was drained and broadly dispersed eastward in Valencia Trough. During the late Pleistocene rise of sea level, the main depocenters progressively shifted shoreward and sedimentation rates greatly decreased from 175 cm/ky on the upper slope during the early transgression to 106 cm/ky on the outer shelf and then to 63 cm/ky on the mid-shelf during the late transgression as the river sediment discharge dropped to half by Holocene time. Maximal sedimentation rates occurred in active depocenters of sediment dispersal such as the Holocene delta (370 cm/ky) or the youngest Pleistocene Oropesa channel-levee complex (705 cm/ky) where deposition rates increased by an order of magnitude or more compared to average Ebro shelf (38 cm/ky) or base-of-slope rates in the Pleistocene (21 cm/ky). The sedimentation rates verify the importance of sea-level control on the progressive change in location of depocenters and amount of sediment supply, but Pleistocene climatic change and deforestation alone can be observed to double river sediment discharge. The latter observation helps explain the anomalously high deposition rates in Pleistocene turbidite systems compared with older systems that may be controlled more by tectonic and sea-level changes alone. During the past 2000 years, in contrast, man has controlled deposition in the Ebro margin system, first by deforestation that more than doubled river sediment discharge and shelf deposition rates to equal those of Pleistocene time; and second by dam contruction that reduced sediment discharge to less than 5% of the normal Holocene discharge. Similar recent discharge reductions from the Nile and Rhone Rivers suggest that loss of the majority of the river sediment supply in the Mediterranean Sea may result in significant erosion of biologically and agriculturally important lobate delta areas. ?? 1990.

A rapid method to estimate Westergren sedimentation rates.

PubMed

Alexy, Tamas; Pais, Eszter; Meiselman, Herbert J

2009-09-01

The erythrocyte sedimentation rate (ESR) is a nonspecific but simple and inexpensive test that was introduced into medical practice in 1897. Although it is commonly utilized in the diagnosis and follow-up of various clinical conditions, ESR has several limitations including the required 60 min settling time for the test. Herein we introduce a novel use for a commercially available computerized tube viscometer that allows the accurate prediction of human Westergren ESR rates in as little as 4 min. Owing to an initial pressure gradient, blood moves between two vertical tubes through a horizontal small-bore tube and the top of the red blood cell (RBC) column in each vertical tube is monitored continuously with an accuracy of 0.083 mm. Using data from the final minute of a blood viscosity measurement, a sedimentation index (SI) was calculated and correlated with results from the conventional Westergren ESR test. To date, samples from 119 human subjects have been studied and our results indicate a strong correlation between SI and ESR values (R(2)=0.92). In addition, we found a close association between SI and RBC aggregation indices as determined by an automated RBC aggregometer (R(2)=0.71). Determining SI on human blood is rapid, requires no special training and has minimal biohazard risk, thus allowing physicians to rapidly screen for individuals with elevated ESR and to monitor therapeutic responses.

PROJECTING THE RESPONSE OF FISH POPULATION GROWTH RATE TO SEDIMENT EXPOSURE

EPA Science Inventory

Sediment is one of the main stressors on stream fish populations in Georgia. Here, a quantitative approach relating sediment exposure to stream fish population dynamics is presented, where equations characterize sediment exposure to vital rates, then vital rates are used in a mat...

43 CFR 11.73 - Quantification phase-resource recoverability analysis.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or sediment properties and adsorption-desorption rates between soil or sediment components and water...) Chemical, physical, and biological removal rates of the oil or hazardous substance from the media involved..., sediments, water, or geologic materials; (B) Transport rates in air, soil, water, and sediments; (C...

High natural erosion rates are the backdrop for enhanced anthropogenic soil erosion in the Middle Hills of Nepal

NASA Astrophysics Data System (ADS)

West, A. J.; Arnold, M.; Aumaître, G.; Bourlès, D. L.; Keddadouche, K.; Bickle, M.; Ojha, T.

2014-08-01

Although agriculturally accelerated soil erosion is implicated in the unsustainable environmental degradation of mountain environments, such as in the Himalaya, the effects of land use can be difficult to quantify in many mountain settings because of the high and variable natural background rates of erosion. In this study, we present new long-term denudation rates, derived from cosmogenic 10Be analysis of quartz in river sediment from the Likhu Khola, a small agricultural river basin in the Middle Hills of central Nepal. Calculated long-term denudation rates, which reflect background natural erosion processes over 1000+ years prior to agricultural intensification, are similar to present-day sediment yields and to soil loss rates from terraces that are well-maintained. Similarity in short- and long-term catchment-wide erosion rates for the Likhu is consistent with data from elsewhere in the Nepal Middle Hills, but contrasts with the very large increases in short-term erosion rates seen in agricultural catchments in other steep mountain settings. Our results suggest that the large sediment fluxes exported from the Likhu and other Middle Hills rivers in the Himalaya are derived in large part from natural processes, rather than from soil erosion as a result of agricultural activity. Because of the high natural background rates, simple comparison of short- and long-term rates may not reveal unsustainable soil degradation, particularly if much of the catchment-scale erosion flux derives from mass wasting. Correcting for the mass wasting contribution in the Likhu implies minimum catchment-averaged soil production rates of ~0.25-0.35 mm yr-1. The deficit between these production rates and soil losses suggests that terraced agriculture in the Likhu may not be associated with a large systematic soil deficit, at least when terraces are well maintained, but that poorly managed terraces, forest and scrubland may lead to rapid depletion of soil resources.

Diurnal variation in rates of calcification and carbonate sediment dissolution in Florida Bay

USGS Publications Warehouse

Yates, K.K.; Halley, R.B.

2006-01-01

Water quality and circulation in Florida Bay (a shallow, subtropical estuary in south Florida) are highly dependent upon the development and evolution of carbonate mud banks distributed throughout the Bay. Predicting the effect of natural and anthropogenic perturbations on carbonate sedimentation requires an understanding of annual, seasonal, and daily variations in the biogenic and inorganic processes affecting carbonate sediment precipitation and dissolution. In this study, net calcification rates were measured over diurnal cycles on 27 d during summer and winter from 1999 to 2003 on mud banks and four representative substrate types located within basins between mud banks. Substrate types that were measured in basins include seagrass beds of sparse and intermediate density Thalassia sp., mud bottom, and hard bottom communities. Changes in total alkalinity were used as a proxy for calcification and dissolution. On 22 d (81%), diurnal variation in rates of net calcification was observed. The highest rates of net carbonate sediment production (or lowest rates of net dissolution) generally occurred during daylight hours and ranged from 2.900 to -0.410 g CaCO3 m-2 d-1. The lowest rates of carbonate sediment production (or net sediment dissolution) occurred at night and ranged from 0.210 to -1.900 g CaCO3 m -2 night-1. During typical diurnal cycles, dissolution during the night consumed an average of 29% of sediment produced during the day on banks and 68% of sediment produced during the day in basins. Net sediment dissolution also occurred during daylight, but only when there was total cloud cover, high turbidity, or hypersalinity. Diurnal variation in calcification and dissolution in surface waters and surface sediments of Florida Bay is linked to cycling of carbon dioxide through photosynthesis and respiration. Estimation of long-term sediment accumulation rates from diurnal rates of carbonate sediment production measured in this study indicates an overall average accumulation rate for Florida Bay of 8.7 cm 1000 yr-1 and suggests that sediment dissolution plays a more important role than sediment transport in loss of sediment from Florida Bay. ?? 2006 Estuarine Research Federation.

Analysis and classification of bedload transport events with variable process characteristics

NASA Astrophysics Data System (ADS)

Kreisler, Andrea; Moser, Markus; Aigner, Johann; Rindler, Rolf; Tritthart, Michael; Habersack, Helmut

2017-08-01

Knowledge about the magnitude of bedload fluxes at given hydraulic conditions in natural streams is essential for improved process understanding, for the application, calibration and validation of bedload transport formulas, and for numerical sediment transport models. Nonetheless, extensive field measurements of bedload transport are challenging and therefore data from such efforts are rare. Bedload transport has been measured comprehensively at the downstream section of the Urslau torrent in Salzburg, Austria, since 2011. We used an integrative monitoring system that combines direct (mobile basket sampler, slot sampler) and indirect measuring devices (geophone plates). Continuous information about the intensity and distribution of bedload transport within the channel cross-section is available in high spatial and temporal resolution. Seven geophone plates at a stream width of 8 m are part of a measurement system that delivers data in 1-min intervals. These geophone data are calibrated using results of direct bedload measurements, providing an opportunity to calculate bedload rates and bedload yields in selected time periods. Continuous data on the bedload transport process over three years enabled assessing several bedload transport events. The investigation of bedload transport rate/discharge relationships reveals order-of-magnitude changes. For individual events, we observed shifts in the data, reflecting different bedload rates at comparable hydraulic conditions. This study reveals that variable sediment supply conditions affect the prevailing bedload transport rates at the Urslau stream. Calculating the bedload transport efficiency enables comparing bedload transport events that exhibit similar process characteristics. Finally, we provide a conceptual model of bedload transport process types as a function of bedload transport efficiency and dimensionless stream power.

Feedbacks Among Rifting, Erosion, Lithospheric Rupture, and Crustal Recycling: From the Colorado River to the Salton Trough and Gulf of California (Invited)

NASA Astrophysics Data System (ADS)

Dorsey, R. J.; Lazear, G. D.

2013-12-01

Many studies examine the influence of climate and erosion on growth of convergent orogens, but feedbacks between tectonics and erosion in extensional and transtensional settings are less well understood. The Colorado River has delivered a huge volume of sediment to rapidly subsiding transtensional basins along the Pacific - North America plate boundary over the past ~5.5 million years. Oblique rifting, rupture, and rapid subsidence drive a newly recognized style of crustal recycling in which sediment is funneled out of the continental interior by a large river and delivered to subsiding basins where it is rapidly converted to a new generation of crust at a rifted continental margin. Transfer of crust can be tracked because the eroding source (Colorado Plateau) and depositional sinks (Salton Trough and northern Gulf of California) are intact and well preserved. Using distribution of late Miocene basalt flows and thermochronologic data, we calculate that 3.4 × 1.2 x 105 km3 of rock has been eroded from the Colorado Plateau since 10 Ma. Most of this erosion occurred starting 5.5-6.0 Ma when the river drainage became integrated and incision rates increased dramatically. Two estimates for the volume of Colorado River sediment stored in basinal sinks since ~5.5 Ma are: (1) 2.8 × 0.6 x 105 km3 assuming that crust between 5 and 10-12 km depth in the plate-boundary basins is young metasedimentary rock mixed with intrusions; or (2) 1.55 × 0.35 x 105 km3 assuming that crust below 4-5 km is thinned pre-Cenozoic crystalline rock. Significant overlap of estimate 1 with the volume eroded from the Plateau provides new support for a model of lithospheric rupture and crustal recycling in the Salton Trough and northern Gulf of California. Assuming an average density of 2.3-2.5 g/cc and the preferred volume estimate above, the total mass of crust transferred is roughly 5.1-11.5 x 1014 metric tons, representing an average annual flux of 156 × 60 Mt/yr since 5.3 Ma (when the Colorado River first arrived in the Salton Trough), or 172 × 66 Mt/yr if we assume all sediment flux took place after 4.8 Ma. The calculated long-term flux is strikingly similar to historical pre-dam sediment discharge measured at Yuma in the early 1900's (172 × 64 Mt/yr). The similarity of flux estimates suggests that rates of erosion and sediment discharge in this system have been consistent, on average, over geologic to modern timescales. We suggest that positive feedback between Late Cenozoic erosion and flexural rebound on the Colorado Plateau may act to sustain steady rates of regional erosion and sediment discharge for millions of years after integration of the Colorado River at ~5.5-6 Ma.

Controls of Sediment Nitrogen Dynamics in Tropical Coastal Lagoons

PubMed Central

Enrich-Prast, Alex; Figueiredo, Viviane; Esteves, Francisco de Assis; Nielsen, Lars Peter

2016-01-01

Sediment denitrification rates seem to be lower in tropical environments than in temperate environments. Using the isotope pairing technique, we measured actual denitrification rates in the sediment of tropical coastal lagoons. To explain the low denitrification rates observed at all study sites (<5 μmol N2 m-2 h-1), we also evaluated potential oxygen (O2) consumption, potential nitrification, potential denitrification, potential anammox, and estimated dissimilatory nitrate (NO3-) reduction to ammonium (NH4+; DNRA) in the sediment. 15NO3- and 15NH4+ conversion was measured in oxic and anoxic slurries from the sediment surface. Sediment potential O2 consumption was used as a proxy for overall mineralization activity. Actual denitrification rates and different potential nitrogen (N) oxidation and reduction processes were significantly correlated with potential O2 consumption. The contribution of potential nitrification to total O2 consumption decreased from contributing 9% at sites with the lowest sediment mineralization rates to less than 0.1% at sites with the highest rates. NO3- reduction switched completely from potential denitrification to estimated DNRA. Ammonium oxidation and nitrite (NO2-) reduction by potential anammox contributed up to 3% in sediments with the lowest sediment mineralization rates. The majority of these patterns could be explained by variations in the microbial environments from stable and largely oxic conditions at low sediment mineralization sites to more variable conditions and the prevalences of anaerobic microorganisms at high sediment mineralization sites. Furthermore, the presence of algal and microbial mats on the sediment had a significant effect on all studied processes. We propose a theoretical model based on low and high sediment mineralization rates to explain the growth, activity, and distribution of microorganisms carrying out denitrification and DNRA in sediments that can explain the dominance or coexistence of DNRA and denitrification processes. The results presented here show that the potential activity of anaerobic nitrate-reducing organisms is not dependent on the availability of environmental NO3-. PMID:27175907

Controls of Sediment Nitrogen Dynamics in Tropical Coastal Lagoons.

PubMed

Enrich-Prast, Alex; Figueiredo, Viviane; Esteves, Francisco de Assis; Nielsen, Lars Peter

2016-01-01

Sediment denitrification rates seem to be lower in tropical environments than in temperate environments. Using the isotope pairing technique, we measured actual denitrification rates in the sediment of tropical coastal lagoons. To explain the low denitrification rates observed at all study sites (<5 μmol N2 m-2 h-1), we also evaluated potential oxygen (O2) consumption, potential nitrification, potential denitrification, potential anammox, and estimated dissimilatory nitrate (NO3-) reduction to ammonium (NH4+; DNRA) in the sediment. 15NO3- and 15NH4+ conversion was measured in oxic and anoxic slurries from the sediment surface. Sediment potential O2 consumption was used as a proxy for overall mineralization activity. Actual denitrification rates and different potential nitrogen (N) oxidation and reduction processes were significantly correlated with potential O2 consumption. The contribution of potential nitrification to total O2 consumption decreased from contributing 9% at sites with the lowest sediment mineralization rates to less than 0.1% at sites with the highest rates. NO3- reduction switched completely from potential denitrification to estimated DNRA. Ammonium oxidation and nitrite (NO2-) reduction by potential anammox contributed up to 3% in sediments with the lowest sediment mineralization rates. The majority of these patterns could be explained by variations in the microbial environments from stable and largely oxic conditions at low sediment mineralization sites to more variable conditions and the prevalences of anaerobic microorganisms at high sediment mineralization sites. Furthermore, the presence of algal and microbial mats on the sediment had a significant effect on all studied processes. We propose a theoretical model based on low and high sediment mineralization rates to explain the growth, activity, and distribution of microorganisms carrying out denitrification and DNRA in sediments that can explain the dominance or coexistence of DNRA and denitrification processes. The results presented here show that the potential activity of anaerobic nitrate-reducing organisms is not dependent on the availability of environmental NO3-.

Modern Deposition Rates and Patterns of Carbon Burial in Southern Fiordland, New Zealand

NASA Astrophysics Data System (ADS)

Ramirez, M. T.; Allison, M. A.; Vetter, L.; Cui, X.; Bianchi, T. S.; Smith, R. W.; Savage, C.; Schüller, S.

2016-02-01

Fjords have been recognized as a hotspot of organic carbon burial, as they accumulate a disproportionate quantity of organic carbon given their areal extent in comparison to other marine settings. However, organic carbon is buried in context with other biogenic and mineral sediments, so localized sedimentation processes play a critical role in determining rates of organic carbon burial. Therefore, it is important to assess the local sources and processes responsible for depositing inorganic sediment as a control on the burial of organic carbon. Here we evaluate three fjords in southern New Zealand that are not glaciated, with a sedimentary system that is dominantly controlled by terrigenous input at fjord heads, reworking of sediments over fjord-mouth sills, and landslide events from the steep fjord walls. Sediment cores were collected throughout the three southernmost fjord systems of Fiordland, New Zealand, and analyzed to determine sedimentary fabric, mass accumulation rates, and organic carbon content. Sediment mass accumulation rates from 210Pb geochronology range up to 500 mg/cm2/yr in proximal and distal areas of the fjords, with lower rates (below 200 mg/cm2/yr) in medial reaches, where terrestrial and marine sediment input is minimal. X-radiographs and 210Pb downcore activity trends show evidence of both mass wasting and surface-sediment bioturbation operating throughout the fjords. Percent organic carbon displays a negative correlation with mass accumulation rate and thickness of the sediment surface mixed layer. Rates of organic carbon accumulation ranged from 3.97 to 21.59 mg/cm2/yr, with a mean of 13.41 mg/cm2/yr. Organic carbon accumulation rates are dependent on the sediment accumulation rate and the percent organic carbon of the sediment. Our results highlight the importance of spatial variability in sedimentation processes and rates within fjords when evaluating organic carbon burial in these systems.

Sediment Relative Paleointensity Record With Slow-sedimentation Rates: Implication For a Chronological Tool In The Slow-sedimentation Sequence

NASA Astrophysics Data System (ADS)

Kanamatsu, T.

2006-12-01

Usefulness of paleointensity records with high-sedimentation rates in stratigraphic correlation have been proved (e.g. Stoner et al., 1998, Laj et al., 2000, Stoner et al., 2000), because the sediment geomagnetic paleointensity data makes possible the fine time correlation between cores on the older sediment than the range of AMS 14C. As father application of the sediment paleointensity for chronological tool, we examined the paleointensity record of much slower sedimentation rate. The paleointensity record of the slower sedimentation sequence is supposed to show the convoluted record by the filtering effect of the post- depositional remanent magnetization, then a unique and different pattern depending on the sedimentation rate (e.g. Guyodo and Channell, 2002). We studied the record of the cores obtained from the West Philippine Sea Basin (Water depth ca. 5000 to 6000 m). The analyses of paleomagnetic direction proved that the cores contain Jaramillo and Olduvai Events. The sedimentation rates of cores estimated from magnetostratigraphy are less than 1cm/kyr (0.6-0.4 cm/kyr). Proxy of paleointensity (NRM20mT/ARM20mT) applied to cores reveals the variations in the records are dominate in c.a. 100 ky cycle. Comparing to other published paleointensity record, it is clear that the record includes ca.100-ky cycle in spite of slower sedimentation rates, although other high frequency records were not identified. It is suggests that geomagnetic events of a few to several kys are recordable in the sediment. The paleointensity in the slow-sedimentation record is still useful for the age control utilizing the lower frequency signal, especially for investigating of less age information sequence such as the deep sea sediment below CCD, but not for fine correlation by high frequency data.

Mountain erosion over decades and millennia: New insights from sediment yields and cosmogenic nuclides

NASA Astrophysics Data System (ADS)

Callahan, R. P.; Riebe, C. S.; Ferrier, K.

2017-12-01

For more than two decades, cosmogenic nuclides have been used to quantify catchment-wide erosion rates averaged over tens of thousands of years. These rates have been used as baselines for comparison with sediment yields averaged over decades, leading to insights on how human activities such as deforestation and agriculture have influenced the production and delivery of sediment to streams and oceans. Here we present new data from the southern Sierra Nevada, California, where sediment yields have been measured over the last ten years using sediment trapping and gauging methods. Cosmogenic nuclides measured in stream sediment reveal erosion rates that are between 13 and 400 (average = 94) times faster than erosion rates inferred from annual accumulations in sediment traps. We show that the discrepancy can be explained by extremely low sediment trapping efficiency, which leads to bias in the short-term rates due to incomplete capture of suspended sediment. Thus the short-term rates roughly agree with the long-term rates, despite intensive timber harvesting in the study catchments over the last century. This differs from results obtained in similar forested granitic catchments of Idaho, where long-term rates are more than ten times greater than short-term rates because large, rare events do not contribute to the short-term averages. Our analysis of a global database indicates that both the magnitude and sign of differences between short- and long-term average erosion rates are difficult to predict, even when the history of land use in known.

Are grain packing and flow turbulence the keys to predicting bedload transport in steep streams? (Invited)

NASA Astrophysics Data System (ADS)

Yager, E.; Monsalve Sepulveda, A.; Smith, H. J.; Badoux, A.

2013-12-01

Bedload transport rates in steep mountain channels are often over-predicted by orders of magnitude, which has been attributed to a range of processes from grain jamming, roughness drag, changes in fluid turbulence and a limited upstream sediment supply. We hypothesize that such poor predictions occur in part because the grain-scale mechanics (turbulence, particle arrangements) of sediment transport are not well understood or incorporated into simplified reach-averaged calculations. To better quantify how turbulence impacts sediment movement, we measured detailed flow velocities and forces at the onset of motion of a single test grain with a fixed pocket geometry in laboratory flume experiments. Of all measured parameters (e.g. flow velocity, shear stress), the local fluid drag force had the highest statistical correlation with grain motion. Use of flow velocity or shear stress to estimate sediment transport may therefore result in erroneous predictions given their relatively low correlation to the onset of sediment motion. To further understand the role of grain arrangement on bedload transport, we measured in situ grain resisting forces to motion (using a force sensor) for a range of grain sizes and patch classes in the Erlenbach torrent, Switzerland (10% gradient). Such forces varied by over two orders of magnitude for a given grain weight and were statistically greater than those calculated using empirical equations for the friction angle. In addition, when normalized by the grain weight, the resisting forces declined with higher grain protrusion above the surrounding bed sediment. Therefore, resisting forces from grain packing and interlocking are substantial and depend on the amount of grain burial. The onset of motion may be considerably under-estimated when calculated solely from measured grain sizes and friction angles. These packing forces may partly explain why critical Shields stresses are higher in steep channels. Such flow and grain parameters also spatially vary in steep streams because of boulder steps and patches of different grain size distributions. To determine if this spatial variation is important for bedload transport, we incorporated probability density functions of flow turbulence and patch grain size distributions into a simple bedload transport equation. Predicted bedload fluxes were significantly improved when distributions of these parameters, rather than single reach-averaged values, were used.

Spatial Patterns of Long-Term Erosion Rates Beneath the Marine West Antarctic Ice Sheet: Insights into the Physics of Continental Scale Glacial Erosion from a Comparison with the Ice-Velocity Field

NASA Astrophysics Data System (ADS)

Howat, I. M.; Tulaczyk, S.; Mac Gregor, K.; Joughin, I.

2001-12-01

As part of the effort to build quantitative models of glacial erosion and sedimentation, it is particularly important to construct scaled relations between erosion, transport, and sedimentation rates and appropriate glaciological variables (e.g., ice velocity). Recent acquisition of bed topography and ice velocity data for the marine West Antarctic Ice Sheet (WAIS)[Joughin et al., 1999; Lythe et al., in press] provides an unprecedented opportunity to investigate continental-scale patterns of glacial erosion and their relationship to the ice velocity field. Utilizing this data, we construct a map of estimated long-term erosion rates beneath the WAIS. In order to calculate long-term erosion rates from the available data, we assume that: (1) the ice sheet has been present for ~5 mill. years, (2) the initial topography beneath the WAIS was that of a typical ( ~200 m.b.s.l.) continental shelf, and (3) the present topography is near local isostatic equilibrium (Airy type). The map of long-term erosion rates constructed in this fashion shows an intriguing pattern of relatively high rates (of the order of 0.1 mm/yr) concentrated beneath modern ice stream tributaries (ice velocity ~100 m/yr), but much lower erosion rates (of the order of 0.01 mm/yr) beneath both the modern fast-moving ice streams ( ~400 m/yr.) and the slow-moving parts of the ice sheet ( ~10 m/yr). This lack of clear correlation between the estimated erosion rates and ice velocity is somewhat unexpected given that both observational and theoretical studies have shown that bedrock erosion rates beneath mountain glaciers can often be calculated by multiplying the basal sliding velocity by a constant (typically of the order of ~10^-4)(Humphrey and Raymond, 1993 and Mac Gregor et al., 2000). We obtain an improved match between estimated erosion rates and bed topography by calculating erosion rates using horizontal gradients within the ice velocity field rather than the magnitude of ice velocity, as consistent with the steady state deforming till model of Cuffey and Alley (1997). Therefore, we hypothesize that the erosional system beneath the WAIS, which has overridden a thick layer of erodible, Tertiary marine sediments (Studinger et al., in press), is 'transport limited' and that the horizontal gradients in ice velocity and till flux have the predominant control over spatial patterns of subglacial erosion and deposition rates. In contrast, past studies of erosional systems have concentrated on mountain glaciers that derive their debris through erosion of hard bedrock. In those cases, the erosional system may be 'production limited' because erosion rates scale with dissipation of gravitational energy, represented by the velocity-times-constant equation. Thus, this concept of a 'transport limited' system represents a deviation from past thinking regarding the dynamics of bed erosion, and may be unique to marine-based ice sheets. Using this concept as a base, we will construct more accurately parameterized models to better define the relationship between the dynamics of ice streams and the character of the sub glacial bed.

Equilibrium and kinetic modeling of contaminant immobilization by activated carbon amended to sediments in the field.

PubMed

Rakowska, Magdalena I; Kupryianchyk, Darya; Koelmans, Albert A; Grotenhuis, Tim; Rijnaarts, Huub H M

2014-12-15

Addition of activated carbons (AC) to polluted sediments and soils is an attractive remediation technique aiming at reducing pore water concentrations of hydrophobic organic contaminants (HOCs). In this study, we present (pseudo-)equilibrium as well as kinetic parameters for sorption of a series of PAHs and PCBs to powdered and granular activated carbons (AC) after three different sediment treatments: sediment mixed with powdered AC (PAC), sediment mixed with granular AC (GAC), and addition of GAC followed by 2 d mixing and subsequent removal ('sediment stripping'). Remediation efficiency was assessed by quantifying fluxes of PAHs towards SPME passive samplers inserted in the sediment top layer, which showed that the efficiency decreased in the order of PAC > GAC stripping > GAC addition. Sorption was very strong to PAC, with Log KAC (L/kg) values up to 10.5. Log KAC values for GAC ranged from 6.3-7.1 and 4.8-6.2 for PAHs and PCBs, respectively. Log KAC values for GAC in the stripped sediment were 7.4-8.6 and 5.8-7.7 for PAH and PCB. Apparent first order adsorption rate constants for GAC (kGAC) in the stripping scenario were calculated with a first-order kinetic model and ranged from 1.6 × 10(-2) (PHE) to 1.7 × 10(-5) d(-1) (InP). Sorption affinity parameters did not change within 9 months post treatment, confirming the longer term effectiveness of AC in field applications for PAC and GAC. Copyright © 2014. Published by Elsevier Ltd.

Temporal variations in supraglacial debris distribution on Baltoro Glacier, Karakoram between 2001 and 2012

NASA Astrophysics Data System (ADS)

Gibson, Morgan J.; Glasser, Neil F.; Quincey, Duncan J.; Mayer, Christoph; Rowan, Ann V.; Irvine-Fynn, Tristram D. L.

2017-10-01

Distribution of supraglacial debris in a glacier system varies spatially and temporally due to differing rates of debris input, transport and deposition. Supraglacial debris distribution governs the thickness of a supraglacial debris layer, an important control on the amount of ablation that occurs under such a debris layer. Characterising supraglacial debris layer thickness on a glacier is therefore key to calculating ablation across a glacier surface. The spatial pattern of debris thickness on Baltoro Glacier has previously been calculated for one discrete point in time (2004) using satellite thermal data and an empirically based relationship between supraglacial debris layer thickness and debris surface temperature identified in the field. Here, the same empirically based relationship was applied to two further datasets (2001, 2012) to calculate debris layer thickness across Baltoro Glacier for three discrete points over an 11-year period (2001, 2004, 2012). Surface velocity and sediment flux were also calculated, as well as debris thickness change between periods. Using these outputs, alongside geomorphological maps of Baltoro Glacier produced for 2001, 2004 and 2012, spatiotemporal changes in debris distribution for a sub-decadal timescale were investigated. Sediment flux remained constant throughout the 11-year period. The greatest changes in debris thickness occurred along medial moraines, the locations of mass movement deposition and areas of interaction between tributary glaciers and the main glacier tongue. The study confirms the occurrence of spatiotemporal changes in supraglacial debris layer thickness on sub-decadal timescales, independent of variation in surface velocity. Instead, variation in rates of debris distribution are primarily attributed to frequency and magnitude of mass movement events over decadal timescales, with climate, regional uplift and erosion rates expected to control debris inputs over centurial to millennial timescales. Inclusion of such spatiotemporal variations in debris thickness in distributed surface energy balance models would increase the accuracy of calculated ablation, leading to a more accurate simulation of glacier mass balance through time, and greater precision in quantification of the response of debris-covered glaciers to climatic change.

The oxygen content of ocean bottom waters, the burial efficiency of organic carbon, and the regulation of atmospheric oxygen

NASA Technical Reports Server (NTRS)

Betts, J. N.; Holland, H. D.

1991-01-01

Data for the burial efficiency of organic carbon with marine sediments have been compiled for 69 locations. The burial efficiency as here defined is the ratio of the quantity of organic carbon which is ultimately buried to that which reaches the sediment-water interface. As noted previously, the sedimentation rate exerts a dominant influence on the burial efficiency. The logarithm of the burial efficiency is linearly related to the logarithm of the sedimentation rate at low sedimentation rates. At high sedimentation rates the burial efficiency can exceed 50% and becomes nearly independent of the sedimentation rate. The residual of the burial efficiency after the effect of the sedimentation rate has been subtracted is a weak function of the O2 concentration in bottom waters. The scatter is sufficiently large, so that the effect of the O2 concentration in bottom waters on the burial efficiency of organic matter could be either negligible or a minor but significant part of the mechanism that controls the level of O2 in the atmosphere.

Structure and sediment budget of Yinggehai-Song Hong basin, South China Sea: Implications for Cenozoic tectonics and river basin reorganization in Southeast Asia

NASA Astrophysics Data System (ADS)

Lei, Chao; Ren, Jianye; Sternai, Pietro; Fox, Matthew; Willett, Sean; Xie, Xinong; Clift, Peter D.; Liao, Jihua; Wang, Zhengfeng

2015-08-01

The temporal link between offshore stratigraphy and onshore topography is of key importance for understanding the long-term surface evolution of continental margins. Here we present a grid of regional, high-quality reflection seismic and well data to characterize the basin structure. We identify fast subsidence of the basin basement and a lack of brittle faulting of the offshore Red River fault in the Yinggehai-Song Hong basin since 5.5 Ma, despite dextral strike-slip movement on the onshore Red River fault. We calculate the upper-crustal, whole-crustal, and whole-lithospheric stretching factors for the Yinggehai-Song Hong basin, which show that the overall extension observed in the upper crust is substantially less than that observed for the whole crust or whole lithosphere. We suggest that fast basement subsidence after 5.5 Ma may arise from crustal to lithospheric stretching by the regional dynamic lower crustal/mantle flow originated by collision between India-Eurasia and Indian oceanic subduction below the Eurasian margin. In addition, we present a basin wide sediment budget in the Yinggehai-Song Hong basin to reconstruct the sedimentary flux from the Red River drainage constrained by high-resolution age and seismic stratigraphic data. The sediment accumulation rates show a sharp increase at 5.5 Ma, which suggests enhanced onshore erosion rates despite a slowing of tectonic processes. This high sediment supply filled the accommodation space produced by the fast subsidence since 5.5 Ma. Our data further highlight two prominent sharp decreases of the sediment accumulation at 23.3 Ma and 12.5 Ma, which could reflect a loss of drainage area following headwater capture from the Paleo-Red River. However, the low accumulation rate at 12.5 Ma also correlates with drier and therefore less erosive climatic conditions.

The influence of bottom boundary layer hydrodynamics on sediment focusing in a contaminated bay.

PubMed

Graham, Neil D; Bouffard, Damien; Loizeau, Jean-Luc

2016-12-01

Understanding the dynamics and fate of particle bound contaminants is important for mitigating potential environmental, economic and health impacts linked to their presence. Vidy Bay, Lake Geneva (Switzerland), is contaminated due to the outfall and overflow from the wastewater treatment plant of the City of Lausanne. This study was designed to investigate the fate of particle-bound contaminants with the goal of providing a more complete picture of contaminant pathways within the bay and their potential spread to the main basin. This goal was achieved by investigating the sediment transport dynamics, using sediment traps and radionuclide tracers, and ascertaining how local bottom-boundary hydrodynamic conditions (temperature, turbidity, current velocity and direction) influence these dynamics. Results of the study indicated that sedimentation rates and lateral advections increased vertically with proximity to the lakebed and laterally with proximity to shore, indicating the presence of sediment focusing in the bay. Hydrodynamic measurements showed the persistent influence of a gyre within the bay, extending down to the lake bed, while just outside of the bay circulation was influenced by the seasonal patterns of the main basin. Calculated mean displacement distances in the bay indicated that suspended particles can travel ∼3 km per month, which is 1.7 times the width of the Vidy Bay gyre. This results in a residence time of approximately 21 days for suspended particles, which is much greater than previously modelled results. The calculated mobility Shield parameter never exceeded the threshold shear stress needed for resuspension in deeper parts of the bay. In such, increased lateral advections to the bay are not likely due to local resuspension but rather external particle sources, such as main basin or shallow, littoral resuspensions. These external sources coupled with an increased residence time and decreased current velocity within the bay are the precipitating factors in sediment focusing. While the spread of contaminants from the bay may occur through the transport of fine suspended sediments in shallower zones of the bay (<60 m) by longshore littoral currents, results suggest that particle-bound contaminants are likely to remain within the bay.

Application of PAH concentration profiles in lake sediments as indicators for smelting activity.

PubMed

Warner, Wiebke; Ruppert, Hans; Licha, Tobias

2016-09-01

The ability of lake sediment cores to store long-term anthropogenic pollution establishes them as natural archives. In this study, we focus on the influence of copper shale mining and smelting in the Mansfeld area of Germany, using the depth profiles of two sediment cores from Lake Süßer See. The sediment cores provide a detailed chronological deposition history of polycyclic aromatic hydrocarbons (PAHs) and heavy metals in the studied area. Theisen sludge, a fine-grained residue from copper shale smelting, reaches the lake via deflation by wind or through riverine input; it is assumed to be the main source of pollution. To achieve the comparability of absolute contaminant concentrations, we calculated the influx of contaminants based on the sedimentation rate. Compared to the natural background concentrations, PAHs are significantly more enriched than heavy metals. They are therefore more sensitive and selective for source apportionment. We suggest two diagnostic ratios of PAHs to distinguish between Theisen sludge and its leachate: the ratio fluoranthene to pyrene ~2 and the ratio of PAH with logKOW<5.7 to PAH with a logKOW>5.7 converging to an even lower value than 2.3 (the characteristic of Theisen sludge) to identify the particulate input in lake environments. Copyright © 2016 Elsevier B.V. All rights reserved.

Numerical study of sediment dynamics during hurricane Gustav

NASA Astrophysics Data System (ADS)

Zang, Zhengchen; Xue, Z. George; Bao, Shaowu; Chen, Qin; Walker, Nan D.; Haag, Alaric S.; Ge, Qian; Yao, Zhigang

2018-06-01

In this study, the coupled ocean-atmosphere-wave-and-sediment transport (COAWST) modeling system was employed to explore sediment dynamics in the northern Gulf of Mexico during hurricane Gustav in 2008. The performance of the model was evaluated quantitatively and qualitatively against in-situ and remote sensing measurements, respectively. After Gustav's landfall in coastal Louisiana, the maximum significant wave heights reached more than 8 m offshore and they decreased quickly as it moved toward the inner shelf, where the vertical stratification was largely destroyed. Alongshore currents were dominant westward on the eastern sector of the hurricane track, and offshoreward currents prevailed on the western sector. High suspended sediment concentrations (>1000 mg/l) were confined to the inner shelf at surface layers and the simulated high concentrations at the bottom layer extended to the 200 m isobaths. The stratification was restored one week after landfall, although not fully. The asymmetric hurricane winds induced stronger hydrodynamics in the eastern sector, which led to severe erosion. The calculated suspended sediment flux (SSF) was convergent to the hurricane center and the maximum SSF was simulated near the south and southeast of the Mississippi river delta. The averaged post-hurricane deposition over the Louisiana shelf was 4.0 cm, which was 3.2-26 times higher than the annual accumulation rate under normal weather conditions.

Modern deposition rates and patterns of organic carbon burial in Fiordland, New Zealand

NASA Astrophysics Data System (ADS)

Ramirez, Michael T.; Allison, Mead A.; Bianchi, Thomas S.; Cui, Xingqian; Savage, Candida; Schüller, Susanne E.; Smith, Richard W.; Vetter, Lael

2016-11-01

Fjords are disproportionately important for global organic carbon (OC) burial relative to their spatial extent and may be important in sequestering atmospheric CO2, providing a negative climate feedback. Within fjords, multiple locally variable delivery mechanisms control mineral sediment deposition, which in turn modulates OC burial. Sediment and OC sources in Fiordland, New Zealand, include terrigenous input at fjord heads, sediment reworking over fjord-mouth sills, and landslide events from steep fjord walls. Box cores were analyzed for sedimentary texture, sediment accumulation rate, and OC content to evaluate the relative importance of each delivery mechanism. Sediment accumulation was up to 3.4 mm/yr in proximal and distal fjord areas, with lower rates in medial reaches. X-radiograph and 210Pb stratigraphy indicate mass wasting and surface-sediment bioturbation throughout the fjords. Sediment accumulation rates are inversely correlated with %OC. Spatial heterogeneity in sediment depositional processes and rates is important when evaluating OC burial within fjords.

Bayesian integration of radioisotope dating (210Pb, 137Cs, 241Am, 14C) and an 18-20th century mining history of Brotherswater, English Lake District

NASA Astrophysics Data System (ADS)

Schillereff, Daniel; Chiverrell, Richard; Macdonald, Neil; Hooke, Janet; Welsh, Katharine; Piliposyan, Gayane; Appleby, Peter

2014-05-01

Lake sediment records are often a useful tool for investigating landscape evolution as geomorphic changes in the catchment are reflected by altered sediment properties in the material transported through the watershed and deposited at the lake bed. Recent research at Brotherswater, an upland waterbody in the Lake District, northwest England, has focused on reconstructing historical floods from their sedimentary signatures and calculating long-term sediment and carbon budgets from fourteen sediment cores extracted from across the basin. Developing accurate chronological control is essential for these tasks. One sediment core (BW11-2; 3.5 m length) from the central basin has been dated using artificial radionuclide measurements (210Pb, 137Cs, 241Am) for the uppermost sediments and radiocarbon (14C) for lower sediments. The core appears to span the past 1500 years, however a number of problems have arisen. We present our explanations for these errors, the independent chronological techniques used to generate an accurate age-depth model for this core and methods for its transferral to the other 13 cores extracted from the basin. Two distinct 137Cs markers, corresponding to the 1986 Chernobyl disaster and 1960s weapons testing, confirm the 210Pb profile for sediment deposition since ~1950, but calculations prior to this appear erroneous, possibly due to a hiatus in the sediment record. We used high-resolution geochemical profiles (measured by XRF) to cross-correlate with a second 210Pb-dated chronology from a more distal location, which returned more sensible results. Unfortunately, the longer 14C sequence exhibits two age-reversals (radiocarbon dates that are too old). We believe the uppermost two dates are erroneous, due to a shift in inflow location as a flood prevention method ~1900 A.D., dated using information from historical maps. The lower age-reversal coincides with greater supply of terrigenous material to the lake (increased Zr, K, Ti concentrations), pointing to a hillslope clearance event. A widespread concurrent hillslope gullying phase in northwest England triggering enhanced soil erosion is thus the most likely explanation, as the presence of old carbon is a known issue for lakes in the region at this time. Applying a Bayesian age-depth modelling protocol is able to account for these age-reversals with some success. However, the greatest uncertainty in the model occurs across the 1700 -1900 A.D. time window as the radiocarbon percentages offer multiple age solutions due to fluctuating atmospheric 14C concentrations from fossil fuel emissions. We address this issue by incorporating into the model geochemical markers in the sediment core related to local point-source Pb mining of known-age; the most-likely age-depth curve is subsequently much more definitively resolved. Usefully, these mining-derived chronological markers bridge the temporal gap between artificial radionuclide and conventional radiocarbon dating which is a common problem in palaeolimnology. These distinctive geochemical mining profiles (Pb, Zn, Cu) have been mapped across all cores, enabling precise core correlation and confident transferral of the age-depth model, and reveal highly spatially variable sediment accumulation rates. This has enabled more accurate sediment and carbon budgets to be calculated and some insight into palaeoflood frequency to be obtained from the Brotherswater sediment sequence.

The importance of earthquake-induced landslides to long-term slope erosion and slope-failure hazards in seismically active regions

USGS Publications Warehouse

Keefer, D.K.

1994-01-01

This paper describes a general method for determining the amount of earthquake-induced landsliding that occurs in a seismically active region over time; this determination can be used as a quantitative measure of the long-term hazard from seismically triggered landslides as well as a measure of the importance of this process to regional slope-erosion rates and landscape evolution. The method uses data from historical earthquakes to relate total volume of landslide material dislodged by an earthquake to the magnitude, M, and seismic moment, M0, of the earthquake. From worldwide data, a linear-regression relation between landslide volume, V, and M0 is determined as: V = M0/1018.9(?? 0.13), where V is measured in m3 and M0 is in dyn-cm. To determine the amount of earthquake-generated landsliding over time, this relation is combined with data on seismic-moment release for a particular region, which may be derived from either earthquake-history or fault-slip data. The form of the M0-V relation allows the rate of production of earthquake-induced landslides over time to be determined from total rate of seismic-moment release without regard to the distribution of individual events, thus simplifying and generalizing the determination. Application of the method to twelve seismically active regions, with areas ranging from 13,275 to 2,308,000 km2, shows that erosion rates from earthquake-induced landslides vary significantly from region to region. Of the regions studied, the highest rates were determined for the island of Hawaii, New Zealand, western New Guinea, and the San Francisco Bay region of California. Significantly lower rates were determined for Iran, Tibet, the Sierra Nevada-Great Basin region of California, and central Japan (for the time period from 715 AD to the present). Intermediate rates were determined for Peru, southern California, onshore California, Turkey, and central Japan (for the time period from 1586 AD to the present). To determine the relative, long-term importance of seismically triggered landslides, these erosion rates are compared to erosion rates calculated for other slope processes and to rates calculated from fluvial sediment discharge. Comparisons with other slope processes indicate that earthquake-induced landslides are the predominant agents of slope erosion on the island of Hawaii, in the San Francisco Bay region, and in western New Guinea. For Hawaii, the San Francisco Bay region, and Sierra Nevada-Great Basin region of California, the erosion rates calculated for earthquake-induced landslides also exceed the regional erosion rates calculated from fluvial sediment discharge. ?? 1994.

Trace-element deposition in the Cariaco Basin, Venezuela Shelf, under sulfate-reducing conditions: a history of the local hydrography and global climate, 20 ka to the present

USGS Publications Warehouse

Piper, David Z.; Dean, Walter E.

2002-01-01

A sediment core from the Cariaco Basin on the Venezuelan continental shelf, which recovered sediment that has been dated back to 20 ka (thousand years ago), was examined for its major-element-oxide and trace-element composition. Cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), nickel (Ni), vanadium (V), and zinc (Zn) can be partitioned between a siliciclastic, terrigenous-derived fraction and two seawater-derived fractions. The two marine fractions are (1) a biogenic fraction represented by nutrient trace elements taken up mostly in the photic zone by phytoplankton, and (2) a hydrogenous fraction that has been derived from bottom water via adsorption and precipitation reactions. This suite of trace elements contrasts with a second suite of trace elements—barium (Ba), cobalt (Co), gallium (Ga), lithium (Li), the rare-earth elements, thorium (Th), yttrium (Y), and several of the major-element oxides—that has had solely a terrigenous source. The partitioning scheme, coupled with bulk sediment accumulation rates measured by others, allows us to determine the accumulation rate of trace elements in each of the three sediment fractions and of the fractions themselves. The current export of organic matter from the photic zone, redox conditions and advection of bottom water, and flux of terrigenous debris into the basin can be used to calculate independently trace-element depositional rates. The calculated rates show excellent agreement with the measured rates of the surface sediment. This agreement supports a model of trace-element accumulation rates in the subsurface sediment that gives a 20-kyr history of upwelling into the photic zone (that is, primary productivity), bottom-water advection and redox, and provenance. Correspondence of extrema in the geochemical signals with global changes in sea level and climate demonstrates the high degree to which the basin hydrography and provenance have responded to the paleoceanographic and paleoclimatic regimes of the last 20 kyr. The accumulation rate of the marine fraction of Mo increased abruptly at about 14.8 ka (calendar years), from less than 0.5 µg cm-2 yr-1 to greater than 4 µg cm-2 yr-1. Its accumulation rate remained high but variable until 8.6 ka, when it decreased sharply to 1 µg cm-2 yr-1. It continued to decrease to 4.0 ka, to its lowest value for the past 15 kyr, before gradually increasing to the present. Between 14.8 ka and 8.6 ka, its accumulation rate exhibited strong maxima at 14.4, 13.0, and 9.9 ka. The oldest maximum corresponds to melt-water pulse IA into the Gulf of Mexico. A relative minimum, centered at about 11.1 ka, corresponds to melt-water pulse IB; a strong maximum occurs in the immediately overlying sediment. The maximum at 13.0 ka corresponds to onset of the Younger Dryas cold event. This pattern to the accumulation rate of Mo (and V) can be interpreted in terms of its deposition from bottom water of the basin, the hydrogenous fraction, under SO42- -reducing conditions, during times of intense bottom-water advection 14.8 ka to 11.1 ka and significantly less intense bottom-water advection 11 ka to the present. The accumulation rate of Cd shows a pattern that is only slightly different from that of Mo, although its deposition was determined largely by the rain rate of organic matter into the bottom water, a biogenic fraction whose deposition was driven by upwelling of nutrient-enriched water into the photic zone. Its accumulation exhibits only moderately high rates, on average, during both melt-water pulses. Its highest rate, and that of upwelling, occurred during the Younger Dryas, and again following melt-water pulse IB. The marine fractions of Cu, Ni, and Zn also have a strong biogenic signal. The siliciclastic terrigenous debris, however, represents the dominant source, and host, of Cu, Ni, and Zn. All four trace elements have a consid-erably weaker hydrogenous signal than biogenic signal. Accumulation rates of the terrigenous fraction, as reflected by accumulation rates of Th and Ga, show strong maxima at 16.2 and 12.7 ka and minima at 14.1 and 11.1 ka. Co, Li, REE, and Y have a similar distribution. The minima occurred during melt-water pulses IA and IB, the maxima during the Younger Dryas and the rise in sea level following the last glacial maximum.

Toxicity risk assessment of mercury, DDT and arsenic legacy pollution in sediments: A triad approach under low concentration conditions.

PubMed

Marziali, L; Rosignoli, F; Drago, A; Pascariello, S; Valsecchi, L; Rossaro, B; Guzzella, L

2017-09-01

The determination of sediment toxicity is challenging due to site-specific factors affecting pollutants distribution and bioavailability, especially when contamination levels are close to expected non-effect concentrations. Different lines of evidence and sensitive tools are necessary for a proper toxicity risk assessment. We examined the case study of the Toce River (Northern Italy), where past industrial activities determined Hg, DDT and As enrichment in sediments. A triad approach comprising chemical, ecotoxicological and ecological analyses (benthic invertebrates) was carried out for risk assessment of residual contamination in river sediments. A "blank" site upstream from the industrial site was selected to compare the other sites downstream. Sediment, water and benthic invertebrate samplings were carried out following standard protocols. Results emphasized that despite the emissions of the industrial site ceased about 20years ago, sediments in the downstream section of the river remain contaminated by Hg, DDT and As with concentrations exceeding Threshold Effect Concentrations. A chronic whole-sediment test with Chironomus riparius showed decreased development rate and a lower number of eggs per mass in the contaminated sediments. Benthic community was analyzed with the calculation of integrated (STAR_ICMi) and stressor-specific metrics (SPEAR pesticide and mean sensitivity to Hg), but no significant differences were found between upstream and downstream sites. On the other hand, multivariate analysis (partial Redundancy Analysis and variation partitioning) emphasized a slight impact on invertebrate community, accounting for 5% variation in taxa composition. Results show that legacy contaminants in sediments, even at low concentrations, may be bioavailable and possibly toxic for benthic invertebrates. At low concentration levels, sensitive and site-specific tools need to be developed for a proper risk analysis. Copyright © 2017 Elsevier B.V. All rights reserved.

An Analytic Equation Partitioning Climate Variation and Human Impacts on River Sediment Load

NASA Astrophysics Data System (ADS)

Zhang, J.; Gao, G.; Fu, B.

2017-12-01

Spatial or temporal patterns and process-based equations could co-exist in hydrologic model. Yet, existing approaches quantifying the impacts of those variables on river sediment load (RSL) changes are found to be severely limited, and new ways to evaluate the contribution of these variables are thus needed. Actually, the Newtonian modeling is hardly achievable for this process due to the limitation of both observations and knowledge of mechanisms, whereas laws based on the Darwinian approach could provide one component of a developed hydrologic model. Since that streamflow is the carrier of suspended sediment, sediment load changes are documented in changes of streamflow and suspended sediment concentration (SSC) - water discharge relationships. Consequently, an analytic equation for river sediment load changes are proposed to explicitly quantify the relative contributions of climate variation and direct human impacts on river sediment load changes. Initially, the sediment rating curve, which is of great significance in RSL changes analysis, was decomposed as probability distribution of streamflow and the corresponding SSC - water discharge relationships at equally spaced discharge classes. Furthermore, a proposed segmentation algorithm based on the fractal theory was used to decompose RSL changes attributed to these two portions. Additionally, the water balance framework was utilized and the corresponding elastic parameters were calculated. Finally, changes in climate variables (i.e. precipitation and potential evapotranspiration) and direct human impacts on river sediment load could be figured out. By data simulation, the efficiency of the segmentation algorithm was verified. The analytic equation provides a superior Darwinian approach partitioning climate and human impacts on RSL changes, as only data series of precipitation, potential evapotranspiration and SSC - water discharge are demanded.

Inversion and Prediction of Consolidation Settlement Characteristics of the Fluvial Sediments Based on Void Ratio Variation in the Northern Modern Yellow River Subaqueous Delta, China

NASA Astrophysics Data System (ADS)

Liu, Xiao; Liu, Jie; Feng, Xiuli

2018-06-01

The modern Yellow River delta is formed near the estuary of the Yellow River with the characteristics of short formation time, efficient sedimentation rate and loose structure which make sediments prone to be compacted and consolidate under the geostatic stress and overburden stress. It is one of the key areas with land subsidence disasters in China, bringing a series of safety hazards to production and living. Based on the data of massive surface cores and ten drill holes ranging from 12 to 40 m obtained from the northern modern Yellow River subaqueous delta, the inversion method suitable for the calculation of consolidation settlement characteristics of the modern Yellow River subaqueous delta is discussed, and the consolidation settlement characteristics of the delta sediments are inversed and predicted in this paper. The actual void ratio of the delta sediments at the depth from 3 to 15 m shows a significant power function relationship with the depth, while the void ratio of the sediments below 15 m changes little with depth. The pre-consolidation settlement (from deposition to sampling) of the delta sediments is between 0.91 and 1.96 m, while the consolidation settlement of unit depth is between 9.6 and 14.0 cm m-1. The post-consolidation settlement (from sampling to stable) of the subaqueous delta sediments is between 0.65 and 1.56 m in the later stage, and the consolidation settlement of unit depth is between 7.6 and 13.1 cm m-1 under the overburden stress. The delta sediments with a buried depth of 3 to 7 m contribute the most to the possible consolidation settlement in the later stage.

Experimental removal of wetland emergent vegetation leads to decreased methylmercury production in surface sediment

USGS Publications Warehouse

Windham-Myers, L.; Marvin-DiPasquale, M.; Krabbenhoft, D.P.; Agee, J.L.; Cox, M.H.; Heredia-Middleton, P.; Coates, C.; Kakouros, E.

2009-01-01

We performed plant removal (devegetation) experiments across a suite of ecologically diverse wetland settings (tidal salt marshes, river floodplain, rotational rice fields, and freshwater wetlands with permanent or seasonal flooding) to determine the extent to which the presence (or absence) of actively growing plants influences the activity of the Hg(II)-methylating microbial community and the availability of Hg(II) to those microbes. Vegetated control plots were paired with neighboring devegetated plots in which photosynthetic input was terminated 4-8 months prior to measurements, through clipping aboveground biomass, severing belowground connections, and shading the sediment surface to prevent regrowth. Across all wetlands, devegetation decreased the activity of the Hg(II)-methylating microbial community (kmeth) by 38%, calculated MeHg production potential (MP) rates by 36%, and pore water acetate concentration by 78%. Decreases in MP were associated with decreases in microbial sulfate reduction in salt marsh settings. In freshwater agricultural wetlands, decreases in MP were related to indices of microbial iron reduction. Sediment MeHg concentrations were also significantly lower in devegetated than in vegetated plots in most wetland settings studied. Devegetation effects were correlated with live root density (percent volume) and were most profound in vegetated sites with higher initial pore water acetate concentrations. Densely rooted wetlands had the highest rates of microbial Hg(II)-methylation activity but often the lowest concentrations of bioavailable reactive Hg(II). We conclude that the exudation of labile organic carbon (e.g., acetate) by plants leads to enhanced microbial sulfate and iron reduction activity in the rhizosphere, which results in high rates of microbial Hg(II)-methyation and high MeHg concentrations in wetland sediment.

Experimental removal of wetland emergent vegetation leads to decreased methylmercury production in surface sediment

USGS Publications Warehouse

Windham-Myers, Lisamarie; Marvin-DiPasquale, Mark; Krabbenhoft, David P.; Agee, Jennifer L.; Cox, Marisa H.; Heredia-Middleton, Pilar; Coates, Carolyn; Kakouros, Evangelos

2009-01-01

We performed plant removal (devegetation) experiments across a suite of ecologically diverse wetland settings (tidal salt marshes, river floodplain, rotational rice fields, and freshwater wetlands with permanent or seasonal flooding) to determine the extent to which the presence (or absence) of actively growing plants influences the activity of the Hg(II)-methylating microbial community and the availability of Hg(II) to those microbes. Vegetated control plots were paired with neighboring devegetated plots in which photosynthetic input was terminated 4–8 months prior to measurements, through clipping aboveground biomass, severing belowground connections, and shading the sediment surface to prevent regrowth. Across all wetlands, devegetation decreased the activity of the Hg(II)-methylating microbial community (kmeth) by 38%, calculated MeHg production potential (MP) rates by 36%, and pore water acetate concentration by 78%. Decreases in MP were associated with decreases in microbial sulfate reduction in salt marsh settings. In freshwater agricultural wetlands, decreases in MP were related to indices of microbial iron reduction. Sediment MeHg concentrations were also significantly lower in devegetated than in vegetated plots in most wetland settings studied. Devegetation effects were correlated with live root density (percent volume) and were most profound in vegetated sites with higher initial pore water acetate concentrations. Densely rooted wetlands had the highest rates of microbial Hg(II)-methylation activity but often the lowest concentrations of bioavailable reactive Hg(II). We conclude that the exudation of labile organic carbon (e.g., acetate) by plants leads to enhanced microbial sulfate and iron reduction activity in the rhizosphere, which results in high rates of microbial Hg(II)-methyation and high MeHg concentrations in wetland sediment.

A Model of Beaver Meadow Complex Evolution in the Silvies River Basin, Oregon.

NASA Astrophysics Data System (ADS)

Nash, C.; Grant, G.; Campbell, S. D.

2014-12-01

There is increasing evidence to suggest that the pervasive incision seen in the American West is due, in part, to the removal of beaver (Castor canadensis) in the first half of the 19th century. New restoration strategies for these systems focus on the reintroduction of beaver and construction of beaver dam analogs. Such dams locally raise streams beds and water tables, reconnect incised channels to their former floodplains, trap sediment, increase hydraulic diversity, and promote riparian vegetation. However, the geomorphic and hydrologic impacts of both the original beaver dams and their analogs are poorly understood. Observations in the Silvies River basin in Oregon, USA - an upland, semi-arid catchment with extremely high historic beaver populations and a presently recovering population, inform a conceptual model for valley floor evolution with beaver dams. The evolution of the beaver dam complex is characterized by eight stages of morphologic adjustment: water impoundment, sediment deposition, pond filling, multi-thread meadow creation, dam breaching, channel incision, channel widening, and floodplain development. Well-constructed beaver dams, given sufficient time and sediment flux, will evolve from a series of ponds to a multi-threaded channel flowing through a wet meadow complex. If a dam in the system fails, due to overtopping, undercutting, lack of maintenance, or abandonment, the upstream channel will concentrate into a single channel and incise, followed over time by widening once critical bank heights are exceeded. From stratigraphic, dendrochronologic, and geomorphic measurements, we are constraining average timescales associated with each stage's duration and transitional period. Measured sedimentation rates behind modern beaver dam analogs on five stream systems permit calculation of sediment flux over recent time periods, and aid in developing regional rates of sediment deposition over a range of drainage areas and gradients. Stratigraphic and dendrochronologic records provide insight into rates of incision, widening, and floodplain development. These measurements are leading to an understanding of the timescales associated with each morphologic stage and transition period, as well as the long-term implications of reintroducing beaver into a wide range of stream systems.

Sea Level Rise Drove Enhanced Coastal Erosion following the Last Glacial Maximum, Southern California, U.S.A.

NASA Astrophysics Data System (ADS)

Sharman, G.; Covault, J. A.; Stockli, D. F.; Sickmann, Z.; Malkowski, M. A.; Johnstone, S.

2017-12-01

Seacliff erosion poses a major threat to southern California coastal communities, including the propensity for episodic cliff failure and damage to residential and commercial property. Rising sea level is predicted to accelerate seacliff retreat, yet few constraints exist on how rapid sea level rise influenced coastal erosion rates in pre-modern timescales. Here we look to the geologic record in submarine fans to investigate changes in relative sediment supply from rivers and coastal erosion, the latter including seacliff retreat and bluffland erosion. To understand how sea level rise driven by past global warming impacted coastal erosion rates, we sampled modern rivers of the Peninsular Ranges and latest Pleistocene-Holocene submarine canyon-fan systems in southern California for detrital zircon U-Pb geochronology (1369 analyses from 10 samples). Modern river samples show a systematic north-south change in grain age populations broadly distributed across Cretaceous time (ca. 70-135 Ma) to a predominance of middle Cretaceous grain ages (ca. 95-115 Ma), reflecting variations in the geologic age of units within each river catchment. The Carlsbad and La Jolla submarine canyon-fan systems, deposited during sea level lowstand and highstand, respectively, exhibit detrital zircon age distributions consistent with derivation from upstream rivers, with mixing in the littoral zone. However, a sample from the Oceanside fan, deposited during rapid sea level rise at ca. 13 ka, is dominated by detrital ages that lack a local source in the northern Peninsular Ranges, including latest Cretaceous, late Jurassic, and Proterozoic ages. However, such grain ages are widespread in Paleogene sedimentary rocks that comprise the shelf and coastal area, suggesting increased sediment supply from coastal and shelf erosion. Assuming that the Oceanside sample is representative of sediment production during sea level rise, sediment mixing calculations suggest a one to two orders of magnitude increase in sediment from coastal erosion relative to river-supplied sediment. Our results thus suggest a significant increase in coastal erosion rates following the Last Glacial Maximum, highlighting the risk that future sea level rise poses to coastal communities.

The role of subglacial microbes in carbon cycling and methane release in the past and present

NASA Astrophysics Data System (ADS)

Stibal, M.; Bech Mikkelsen, A.; Wadham, J. L.; Telling, J.; Hawkings, J.; Lis, G. P.; Lawson, E. C.; Hasan, F.; Dubnick, A.; Elberling, B.; Jacobsen, C. S.

2012-12-01

Subglacial environments are largely anoxic, contain organic carbon (OC) overridden by glacier ice during periods of advance, and harbour active microbial communities. This creates favourable conditions for a variety of microbial metabolisms, including methanogenesis. Yet little is known of the past and present potentials of subglacial microbes to take part in carbon cycling including methane production. Here we present data on the abundance and diversity of prokaryotic microbes, the activity of methanogenic archaea and the amount and character of OC in subglacial sediment and runoff from the Greenland Ice Sheet and compare them to those from other Arctic glaciers. The investigated Greenland subglacial sediment was of Holocene-aged soil origin and contained less bioavailable OC compared to subglacial sediments of lacustrine origin. The total microbial abundance and diversity was relatively low and the community was dominated by Proteobacteria. The identified clones were related to bacteria with both aerobic and anaerobic metabolisms, indicating the presence of both oxic and anoxic conditions in the sediments. Significant numbers of methanogens (up to 7×104 cells g-1) were detected and clones of Methanomicrobiales were identified in the clone library. Long lag periods (up to >200 days) were observed before significant methane concentrations (~0.2 pmol g-1 day-1 at 1C) were measured in long-term incubation experiments. These rates were lower than those measured in subglacial sediments containing more bioavailable OC. We use the measured rates of methanogenesis to estimate the potential for methane production beneath the Laurentide/Inuitian/Cordilleran and Fennoscandian Ice Sheets during a typical 85 ka Quaternary glacial/interglacial cycle. We predict that contrasting rates of methane production are likely to occur beneath glaciers that overran different types of substrate. Methane production from overridden soils such as those in Greenland is likely to be lower than that from lacustrine-derived sediments, possibly due to a difference in organic substrate lability. This finding highlights the importance of considering the character of different OC pools when calculating present and predicting future subglacial CH4 production rates. We also examine the modern potential of subglacial microbes, including methanogens, to be exported to downstream ecosystems in an active state, and suggest that due to the accelerated melting of glaciers and ice sheets worldwide large amounts of active microbes are transported to downstream ecosystems where they can resume their activity.

Fluvial responses to land-use changes and climatic variations within the Drury Creek watershed, southern Illinois

NASA Astrophysics Data System (ADS)

Miller, Suzanne Orbock; Ritter, Dale F.; Kochel, R. Craig; Miller, Jerry R.

1993-04-01

Fluvial responses to climatic variation and Anglo-American settlement were documented for the Drury Creek watershed, southern Illinois by examining stratigraphic, geomorphic, climatic, and historical data. Regional analyses of long-term precipitation records document a period of decreasing mean annual precipitation from 1904 to about 1945, and an increasing trend in annual precipitation from 1952 to the present. The period between 1945 and 1951 experienced a large number of intense storms that resulted in high annual precipitation totals. Statistical relationships illustrate that changes in precipitation totals are transferred to the hydrologic system as fluctuations in stream discharge. Historical records of southern Illinois show that a maximum period of settlement and deforestation occurred between the 1860s and 1920s. This era ended in the 1940s when large tracts of land were revegetated in an attempt to curtail erosion which had caused extensive upland degradation. In response to hillslope erosion at least two meters of fine-grained sediments were deposited on valley floors. Average sedimentation rates, determined using decdrochronologic techniques, are estimated to be 2.11 cm/yr for the period between 1890 and 1988; rates that are 1 to 2 orders of magnitude greater than pre-settlement values calculated for other areas of the midwest. However, botanical data suggest that aggradation was episodic, possibly occurring during three periods characterized by greater annual precipitation. Since the 1940s, sedimentation rates have declined. Reduced rates of sedimentation are related to an episode of channel entrenchment that reduced overbank flooding. Entrenchment coincided with a period of: (1) reduced sediment yields associated with watershed revegetation and the introduction of soil conservation practices, and (2) intense storm activity that resulted in long periods of high discharge. As a result of channel incision and hillslope erosion, newly exposed bedrock in upstream areas currently provides a source of gravel load to the channels. The distribution of coarse bedload material along tributary streams combined with downstream decreases in width:depth ratios and tractive force estimates suggest that channels in the Drury Creek watershed are slowly adjusting their configuration to transport coarse bedload material. The fluvial response to the increased influx of coarse sediment began more than 45 years ago and continues today.

Efficiency of erosion mitigation strategies in reducing sediment-loading rates from unpaved road networks into coral reef-bearing waters of the Eastern Caribbean

NASA Astrophysics Data System (ADS)

Ramos-Scharron, Carlos; Gray, Sarah; Sears, Whitney

2014-05-01

Erosion from unpaved road networks represents a critical source of stress affecting the coral reef systems of the U.S. Virgin Islands in the Northeastern Caribbean. Combined community- and government-driven efforts to reduce sediment contributions from unpaved roads in the island of St. John have consisted in improving road drainage design, paving selected road segments, and constructing sediment retention structures. Here we describe empirical evidence attesting to the efficacy of these mitigation efforts. Road drainage improvements reduced sediment production rates to about a third of pre-treatment levels. Road-segment scale erosion rates following paving ranged from 5-30% of pre-treatment levels, depending on road slope and road grading frequency. A 616-m3 sediment retention pond proved to contain 86 Mg of sediment annually and about 94% of the runoff generated from a 12 ha sub-catchment with an unpaved road density of 19 km km-2. Watershed-scale modeling evaluations suggested that the combination of these three treatments within the 13-km2 Coral Bay watershed resulted in the reduction of annual sediment delivery rates from 445 Mg yr-1 to 327 Mg yr-1. Cost-effectiveness analyses suggest that road drainage improvements and construction of the detention pond provided the greatest reductions in sediment delivery per total amount of funds spent. Even though paving is a proven erosion control method, the high costs involved made it a relatively cost-inefficient method. Marine sedimentation of terrigenous sediment (land-derived) was regularly monitored (every 26 days) at 15 near-shore and reef sites from 2008 to 2013 below the treated and undeveloped watersheds. Sediment composition (% terrigenous) determined by loss on ignition was multiplied by the total sediment accumulation rate in tube sediment traps to obtain terrigenous sediment accumulation rates (in mg cm-2 d-1). Mean terrigenous sediment accumulation rates were over 24 (near-shore) and 6 (reef) times greater below developed compared to undeveloped watersheds. Comparisons of marine terrigenous accumulation rates between undeveloped and developed areas were consistent with those based on modeled sediment yields. At all near-shore sites below mitigated watersheds, mean post-mitigation marine terrigenous sediment accumulation rates were reduced by up to 70% of mean pre-mitigation values. Nevertheless, further analysis is required to evaluate whether the observed post-mitigation reduction is strictly related to watershed restoration. At the developed coral reef sites, acute terrigenous sediment accumulation rates during major storms equaled or exceeded coral-stressing levels (>50 mg cm-2d-1). Results from this research are being employed in the design of mitigation strategies within our study areas as well as in other parts of the Caribbean where roads are considered a major threat to coral reefs.

Sedimentation rates measurements in former channels of the upper Rhône river using Chernobyl 137Cs and 134Cs as tracers.

PubMed

Rostan, J C; Juget, J; Brun, A M

1997-01-30

Former river channels are aquatic ecosystems with a different geomorphology generated by fluvial dynamics more or less linked to the main channel. They present different ecological successions to become terrestrial ecosystems and are thus supposed to have different sedimentation rates. The aim of this paper is to assess this sedimentation rate using radioactive tracer methodology commonly used in lake studies. Chernobyl impacts, expressed in 137Cs concentration and 137Cs/134Cs ratio, were determined in sediment cores. Sites (21) were sampled in the alluvial plain of the Upper Rhône River from 1989 to 1994. The contamination presented a high spatial heterogeneity. The maximum values encountered by site ranged between 34 and 541 Bq/kg of dry matter. The method generally gave good core profiles. Sedimentation rate ranged between 0.14 and 0.70 cm/year for the former meanders and between 0.14 and 2.86 cm/year for the braided channels. The sediment accumulation rates ranged from 0.03 to 0.25 g/cm2 per year and 0.03 to 2.26 g/cm2 per year, respectively. These values are similar to those found for Lake Geneva. The importance of the former channels in relation to the main channel is enhanced by the higher contamination and radionuclides retention. The sediment accumulation rate is related to the organic carbon content in the sediment. A comparison between two former channels with different productivity showed that the the allogenous driven system presents a high organic sediment accumulation rate with a low organic content in the sediment and inversely, a low organic sediment accumulation rate with a high organic carbon content was found for the autogenous drive system.

Physical-chemical studies of proteins of squid nerve axoplasm, with special reference to the axon fibrous protein.

PubMed

DAVISON, P F; TAYLOR, E W

1960-03-01

The proteins in the axoplasm of the squid, Dosidicus gigas, have been resolved electrophoretically into a major fraction including the fibrous protein, and possibly its structural subunits, and a minor fraction including at least two proteins with low sedimentation coefficients. A partially reversible change in the structure of the fibrous protein occurs under the action of 0.4 M salt or high pH. These experiments have been interpreted to indicate that in the intact fiber one, or a few, protofibrils are arranged helically or longitudinally along the fiber axis, and linked by electrostatic bonds. On the dissociation of these bonds the separated protofibrils assume a less extended form and sediment more rapidly than the intact fibers. Some material with a lower sedimentation rate is also released on the dissociation. This fraction may comprise smaller chain fragments. The volume fraction and the approximate refractive index of the fibers have been calculated.

Physical-Chemical Studies of Proteins of Squid Nerve Axoplasm, with Special Reference to the Axon Fibrous Protein

PubMed Central

Davison, Peter F.; Taylor, Edwin W.

1960-01-01

The proteins in the axoplasm of the squid, Dosidicus gigas, have been resolved electrophoretically into a major fraction including the fibrous protein, and possibly its structural subunits, and a minor fraction including at least two proteins with low sedimentation coefficients. A partially reversible change in the structure of the fibrous protein occurs under the action of 0.4 M salt or high pH. These experiments have been interpreted to indicate that in the intact fiber one, or a few, protofibrils are arranged helically or longitudinally along the fiber axis, and linked by electrostatic bonds. On the dissociation of these bonds the separated protofibrils assume a less extended form and sediment more rapidly than the intact fibers. Some material with a lower sedimentation rate is also released on the dissociation. This fraction may comprise smaller chain fragments. The volume fraction and the approximate refractive index of the fibers have been calculated. PMID:13814536

Direct connectivity between upstream and downstream promotes rapid response of lower coastal-plain rivers to land-use change

NASA Astrophysics Data System (ADS)

Mattheus, Christopher R.; Rodriguez, Antonio B.; McKee, Brent A.

2009-10-01

Low-relief fluvial systems that originate in the lower coastal plain and discharge into estuaries are common along passive margins. These watersheds are thought to be disconnected from their termini by floodplains, which buffer the sediment-routing system by sequestration. Here, we present a detailed study of the Newport River, a typical lower coastal-plain system, which reveals high connectivity between watershed and delta. Connectivity is measured as the time lag between initiation of a silviculture operation, which increased landscape erosion, and when the sediment appeared at the bay-head delta. The time lag, measured from aerial photographs and sedimentation rates calculated from 210Pb- and 137Cs-activities in cores from the watershed and delta, is <3 years. Most lower coastal-plain rivers are steeper and have less floodplain accommodation available for storage than their larger counterparts that originate landward of the fall line, which promotes higher connectivity between upstream and downstream.

Sedimentation Survey of Lago El Guineo, Puerto Rico, October 2001

USGS Publications Warehouse

Soler-López, Luis R.

2003-01-01

Lago El Guineo has lost about 17.5 percent of its original storage capacity in 70 years because of sediment accumulation. The water volume has been reduced from 2.29 million cubic meters in 1931, to 2.03 million cubic meters in 1986, and to 1.89 million cubic meters in 2001. The average annual storage-capacity loss (equal to the sedimentation rate) of Lago El Guineo was 4,727 cubic meters for the period of 1931 to July 1986 (or 0.21 percent per year), increasing to 5,714 cubic meters for the period of 1931 to October 2001 (or 0.25 percent per year). Discrepancies that could lead to substantial errors in volume calculations in a small reservoir like Lago El Guineo, were found when transferring the field-collected data into the geographic information system data base 1:20,000 U.S. Geological Survey Jayuya, Puerto Rico quadrangle. After verification and validation of field data, the Lago El Guineo shoreline was rectified using digital aerial photographs and differential global positioning data.

Wave forecasting and longshore sediment transport gradients along a transgressive barrier island: Chandeleur Islands, Louisiana

NASA Astrophysics Data System (ADS)

Georgiou, Ioannis Y.; Schindler, Jennifer K.

2009-12-01

Louisiana barrier islands, such as the chain surrounding the southeast region of the state, are experiencing rapid loss of land area, shoreline erosion, and landward migration due to transgression and in-place drowning, and the landfall of several major hurricanes in the last decade. Observations of migration rates and overall impacts to these barrier islands are poorly understood since they do not respond in a traditional way, such as barrier rollover. This paper aims to verify how wave energy and potential longshore sediment transport trends have influenced the recent evolution of the Chandeleur Islands, by direct comparison with recent observations of migration and erosion trends. The Chandeleur Islands are characterized by a bidirectional transport system, with material moving from the central arc to the flanks. The longshore sediment transport along the barrier islands was calculated after propagation and transformation of waves to breaking (generated using observed winds), and through the use of a common longshore sediment transport formula. Seasonal variations in wind climate produced changes in the transport trends and gradients that agree with migration and rotation patterns observed for this barrier island system. Results suggest that wind dominance produces seasonal oscillations that cause an imbalance in the resulting transport gradients that over time are responsible for higher rates of transport in the northward direction. These results and data from other works verify the evolutionary model previously suggested, and qualitatively confirm the recent observations in asymmetric shoreline erosion.

Anthropogenic influence on recent bathymetric change in west-central San Francisco Bay

USGS Publications Warehouse

Barnard, Patrick L.; Kvitek, Rikk G.

2010-01-01

Two multibeam sonar surveys of west-central San Francisco Bay, California, were conducted in 1997 and 2008. Bathymetric change analysis between the two surveys indicates a loss of 14.1 million cubic meters (-3.1 cm/yr-1) of sediment during this time period, representing an approximately three-fold acceleration of the rate that was observed from prior depth change analysis from 1947 to 1979 for all of Central Bay, using more spatially coarse National Ocean Service (NOS) soundings. The portions of the overlapping survey areas between 1997 and 2008 designated as aggregate mining lease sites lost sediment at five times the rate of the remainder of west-central San Francisco Bay. Despite covering only 28% of the analysis area, volume change within leasing areas accounted for 9.2 million cubic meters of sediment loss, while the rest of the area lost 4.9 million cubic meters of sediment. The uncertainty of this recent analysis is more tightly constrained due to more stringent controls on vertical and horizontal position via tightly coupled, inertially aided differential Global Positioning Systems (GPS) solutions for survey vessel trajectory that virtually eliminate inaccuracies from traditional tide modeling and vessel motion artifacts. Further, quantification of systematic depth measurement error can now be calculated through comparison of static surfaces (e.g., bedrock) between surveys using seafloor habitat maps based on acoustic backscatter measurements and ground-truthing with grab samples and underwater video. Sediment loss in the entire San Francisco Bay Coastal System during the last half-century,as estimated from a series of bathymetric change studies, is 240 million cubic meters, and most of this is believed to be coarse sediment (i.e., sand and gravel) from Central Bay and the San Francisco Bar, which is likely to limit the sand supply to adjacent, open-coast beaches. This hypothesis is supported by a calibrated numerical model in a related study that indicates that there is a potential net export of sand-sized sediment across the Golden Gate, suggesting that a reduction in the supply of sand-sized sediment within west-central San Francisco Bay will limit transport to the outer coast.

Trends in Accretion Rates of Riverine Sediments in a Distal Bay and Wetlands Using 7-Beryllium as a Tracer: Fourleague Bay, Louisiana.

NASA Astrophysics Data System (ADS)

Restreppo, G. A.; Bentley, S. J.; Wang, J.; Xu, K.

2017-12-01

To combat land loss along the Mississippi River Delta, Louisiana has launched a historic campaign to sustain and regrow coastal lands using, in part, sediment diversions. Previous research has focused primarily on sand sized sediment load, which is usually deposited proximal to a river's delta or a diversion's outlet. Fine sediments constitute the majority of sediment load in the Mississippi, but are under-studied with respect to dispersal processes, particularly in terms of sediment supply to distal deltaic bays and wetlands. The Atchafalaya River and associated wetlands serve as prime study areas for this purpose. Bimonthly time-series push cores were collected from May 2015 to May 2016 along ten sites within Fourleague Bay, Louisiana. Fourleague Bay has remained stable against the deteriorative effects of relative sea level rise, standing out along Louisiana's declining coastline. Of the ten field sites, five are located across a longitudinal transect in the middle bay, while the other five are located in adjacent marshes. All sites fall within 10 to 30 km of the Atchafalaya Delta, extending south towards the Gulf of Mexico. Cores were extruded in 2 cm intervals, dried, ground, and analyzed via gamma spectrometry for the presence of 7Be. Inventories of 7Be were then calculated and used to determine daily mass accretion rate (MAR) over twelve months. Average MAR values for the bay and the marshes are compared with Atchafalaya River discharge, wind data, and atmospheric pressure through the year of sampling. Peak marsh MAR, 0.88 ± 0.20 kg m-2 d-1, occurs just after historically high river discharge. Peak bay MAR, 1.2 ± 0.67 kg m-2 d-1, occurs during seasonal low river discharge and calm winds. Average bay and marsh MARs have a moderate to strong, negative correlation when compared. Results indicate sediment bypass of the bay floor during periods of moderate to high river discharge, entering the marshes directly when inundation occurs and enhanced by the passage of strong atmospheric fronts. Only during periods of low river discharge and relatively calm winds do riverine sediments aggregate directly onto the bay floor.

Estimating rates of authigenic carbonate precipitation in modern marine sediments

NASA Astrophysics Data System (ADS)

Mitnick, E. H.; Lammers, L. N.; DePaolo, D. J.

2015-12-01

The formation of authigenic carbonate (AC) in marine sediments provides a plausible explanation for large, long-lasting marine δ13C excursions that does not require extreme swings in atmospheric O2 or CO2. AC precipitation during diagenesis is driven by alkalinity production during anaerobic organic matter oxidation and is coupled to sulfate reduction. To evaluate the extent to which this process contributes to global carbon cycling, we need to relate AC production to the geochemical and geomicrobiological processes and ocean chemical conditions that control it. We present a method to estimate modern rates of AC precipitation using an inversion approach based on the diffusion-advection-reaction equation and sediment pore fluid chemistry profiles as a function of depth. SEM images and semi-quantitative elemental map analyses provide further constraints. Our initial focus is on ODP sites 807 and 1082. We sum the diffusive, advective, and reactive terms that describe changes in pore fluid Ca and Mg concentrations due to precipitation of secondary carbonate. We calculate the advective and diffusive terms from the first and second derivatives of the Ca and Mg pore fluid concentrations using a spline fit to the data. Assuming steady-state behavior we derive net AC precipitation rates of up to 8 x 10-4 mmol m-2 y-1 for Site 807 and 0.6 mmol m-2 y-1 for Site 1082. Site 1082 sediments contain pyrite, which increases in amount down-section towards the estimated peak carbonate precipitation rate, consistent with sulfate-reduction-induced AC precipitation. However, the presence of gypsum and barite throughout the sediment column implies incomplete sulfate reduction and merits further investigation of the biogeochemical reactions controlling authigenesis. Further adjustments to our method could account for the small but non-negligible fraction of groundmass with a CaSO4 signature. Our estimates demonstrate that AC formation may represent a sizeable flux in the modern global carbon cycle, on order of 1013 g C y-1. Further, it is likely to have played an even more impactful role in the Paleozoic and Precambrian, when lower surface O2 concentrations created reducing conditions favoring increased carbon burial and alkalinity production during diagenesis.

Oscillatory bedload transport: Data review and simple formulation

NASA Astrophysics Data System (ADS)

Hallermeier, Robert J.

1982-11-01

This review displays over 700 rates of sediment transport by oscillatory flow from 20 sources. Sediments include fine sands to pebbles, both of quartz and of lightweight materials, and the transport rates in water range over seven orders of magnitude. Most data are average gross (to and fro) bedload rates collinear with laboratory flow over a horizontal sediment bed, although other situations with net transport, suspended load, or oblique field waves are considered. As peak flow velocity nears twice the threshold velocity for sediment motion, bedload appears to be fully developed and the transport rate is near that given by a simple formula including flow frequency and peak velocity, and sediment size and density. At lesser peak velocities, bedload rates are markedly smaller and distinctly different regimes of sediment mobilization and transport may be identified.

Effects of Polychlorinated Biphenyl Congener Concentration and Sediment Supplementation on Rates of Methanogenesis and 2,3,6-Trichlorobiphenyl Dechlorination in an Anaerobic Enrichment

PubMed Central

Boyle, Alfred W.; Blake, Cheryl K.; Price, W. Allen; May, Harold D.

1993-01-01

We have employed a method of enrichment that allows us to significantly increase the rate of reductive polychlorinated biphenyl (PCB) dechlorination. This method shortens the time required to investigate the effects that culture conditions have on dechlorination and provides an estimate of the potential activity of the PCB-dechlorinating anaerobes. The periodic supplementation of sterile sediment and PCB produced an enhanced, measurable, and sustained rate of dechlorination. We observed volumetric rates of the dechlorination of 2,3,6-trichlorobiphenyl (2,3,6-CB) to 2,6-dichlorobiphenyl (2,6-CB) of more than 300 μmol liter-1 day-1 when the cultures were supplemented daily. A calculation of this activity that is based on an estimate of the number of dechlorinating anaerobes present indicates that 1.13 pmol of 2,3,6-CB was dechlorinated to 2,6-CB day-1 bacterial cell-1. This rate is similar to that of the reductive dechlorination of 3-chlorobenzoate by Desulfomonile tiedjei. Methanogenesis declined from 585.3 to 125.9 μmol of CH4 liter-1 day-1, while dechlorination increased from 8.2 to 346.0 μmol of 2,3,6-CB dechlorinated to 2,6-CB liter-1 day-1. PMID:16349045

Evaluating physical and biological influences on sedimentation in a tidal freshwater marsh with 7Be

NASA Astrophysics Data System (ADS)

Palinkas, Cindy M.; Engelhardt, Katharina A. M.; Cadol, Dan

2013-09-01

Key differences exist between tidal fresh- and saltwater marshes, such as the relative importance of mineral versus organic sedimentation and plant species diversity, that likely result in different drivers of sedimentation. In tidal freshwater marshes, we hypothesize that vegetation composition, along with physical marsh features (i.e., elevation and tidal channels), play a critical role in sedimentation. This hypothesis is evaluated in Dyke Marsh Preserve (Potomac River, VA, USA) by examining sediment character (grain size, organic content) and deposition rates across the marsh in spring and summer 2010 and 2011. 7Be is especially well suited to capture seasonal sedimentation patterns owing to its short half-life (53.3 d) and ability to assess both sediment deposition and erosion. However, its use in marshes can be challenging, especially due the presence of vegetation. In this study, 7Be-derived sedimentation rates are compared with sediment deposition observed on ceramic tiles to assess its utility in tidal freshwater marshes, and biophysical influences on sediment deposition are examined through statistical models. 7Be- and tile-derived sedimentation rates show similar spatial and temporal patterns, with highest rates occurring at sites closer to tidal channels, highlighting the importance of sediment availability. In addition, complex feedbacks between sedimentation and the plant community are discussed.

High resolution paleo-geomagnetic field variations as recorded in sediments from Prince William Sound, Alaska

NASA Astrophysics Data System (ADS)

Ziegler, Leah; Stoner, Joseph

2013-04-01

The dynamic changes in the Earth's magnetic field, caused by fluid motions in its outer core, can be captured in global marine sediments. Here we extend recent efforts to reconstruct Holocene paleomagnetic secular variation and environmental conditions in the mid-high latitude North Pacific with analyses of a marine sediment core taken from Prince William Sound, southern Alaska. Natural and laboratory remanent magnetizations were studied by progressive alternating field (AF) demagnetization of u-channel samples from jumbo piston core EW0408-95JC (60.66278N, 147.70847W, water depth 745m). The lithology is monitored by physical properties measurements, including CT Scans and core descriptions. The lithology of the upper 8.5 m of the 17.6 meter core consists primarily of magnetically homogenous bioturbated muds. Component directions calculated by PCA analysis are characterized by low MAD values (<4°) with inclinations consistent with GAD predictions and declinations varying in a manner consistent with PSV. Normalized remanences are comparable using a variety of normalizers and show minimal scatter through demagnetization suggesting that reliable paleointenisty estimates may be preserved. A detailed chronology developed from calibrated radiocarbon dating of benthic forams shows that the 8.5m spans ~1500 years, and yields sedimentation rates of several hundred cm/kyr - ultra high for marine sediments. Comparison with Pacific Northwest and broader North American records, provides a degree of reproducibility and allows us to assess the spatial scale of signal coherence at centennial resolution . The resulting record of paleosecular variation (PSV) and relative paleointensity are consistent with predictions from global geomagnetic field models, yet allow investigations of rates of change of the local field, that cannot be accessed from global field models.

Relationship between soil erodibility and modeled infiltration rate in different soils

NASA Astrophysics Data System (ADS)

Wang, Guoqiang; Fang, Qingqing; Wu, Binbin; Yang, Huicai; Xu, Zongxue

2015-09-01

The relationship between soil erodibility, which is hard to measure, and modeled infiltration rate were rarely researched. Here, the soil erodibility factors (K and Ke in the USLE, Ki and K1 in the WEPP) were calculated and the infiltration rates were modeled based on the designed laboratory simulation experiments and proposed infiltration model, in order to build their relationship. The impacts of compost amendment on the soil erosion characteristics and relationship were also studied. Two contrasting agricultural soils (bare and cultivated fluvo-aquic soils) were used, and different poultry compost contents (control, low and high) were applied to both soils. The results indicated that the runoff rate, sediment yield rate and soil erodibility of the bare soil treatments were generally higher than those of the corresponding cultivated soil treatments. The application of composts generally decreased sediment yield and soil erodibility but did not always decrease runoff. The comparison of measured and modeled infiltration rates indicated that the model represented the infiltration processes well with an N-S coefficient of 0.84 for overall treatments. Significant negative logarithmic correlations have been found between final infiltration rate (FIR) and the four soil erodibility factors, and the relationship between USLE-K and FIR demonstrated the best correlation. The application of poultry composts would not influence the logarithmic relationship between FIR and soil erodibility. Our study provided a useful tool to estimate soil erodibility.

Exchanges of sediment between the flood plain and channel of the Amazon River in Brazil

USGS Publications Warehouse

Dunne, T.; Mertes, L.A.K.; Meade, R.H.; Richey, J.E.; Forsberg, B.R.

1998-01-01

Sediment transport through the Brazilian sector of the Amazon River valley, a distance of 2010 km, involves exchanges between the channel and the flood plain that in each direction exceed the annual flux of sediment out of the river at O??bidos (???1200 Mt yr-1). The exchanges occur through bank erosion, bar deposition, settling from diffuse overbank flow, and sedimentation in flood-plain channels. We estimated the magnitude of these exchanges for each of 10 reaches of the valley, and combined them with calculations of sediment transport into and out of the reaches based on sediment sampling and flow records to define a sediment budget for each reach. Residuals in the sediment budget of a reach include errors of estimation and erosion or deposition within the channel. The annual supply of sediment entering the channel from bank erosion was estimated to average 1570 Mt yr-1 (1.3 ?? the O??bidos flux) and the amount transferred from channel transport to the bars (380 Mt yr-1) and the flood plain (460 Mt yr-1 in channelized flow; 1230 Mt yr-1 in diffuse overbank flow) totaled 2070 Mt yr-1 (1.7 ?? the O??bidos flux). Thus, deposition on the bars and flood plain exceeded bank erosion by 500 Mt yr-1 over a 10-16 yr period. Sampling and calculation of sediment loads in the channel indicate a net accumulation in the valley floor of approximately 200 Mt yr-1 over 16 yr, crudely validating the process-based calculations of the sediment budget, which in turn illuminate the physical controls on each exchange process. Another 300-400 Mt yr-1 are deposited in a delta plain downstream of O??bidos. The components of the sediment budget reflect hydrologie characteristics of the valley floor and geomorphic characteristics of the channel and flood plain, which in turn are influenced by tectonic features of the Amazon structural trough.

Incision and Landsliding Lead to Coupled Increase in Sediment Flux and Grain Size Export

NASA Astrophysics Data System (ADS)

Roda-Boluda, D. C.; Brooke, S.; D'Arcy, M. K.; Whittaker, A. C.; Armitage, J. J.

2017-12-01

The rates and grain sizes of sediment fluxes modulate the dynamics and timing of landscape response to tectonics, and dictate the depositional patterns of sediment in basins. Over the last decades, we have gained a good quantitative understanding on how sediment flux and grain size may affect incision and basin stratigraphy. However, we comparably still have limited knowledge on how these variables change with varying tectonic rates. To address this question, we have studied 152 catchments along 8 normal fault-bounded ranges in southern Italy, which are affected by varying fault slip rates and experiencing a transient response to tectonics. Using a data set of 38 new and published 10Be erosion rates, we calibrate a sediment flux predictive equation (BQART), in order to estimate catchment sediment fluxes. We demonstrate that long-term sediment flux is governed by fault slip rates and the tectonically-controlled transient incision, and that sediment flux estimates from the BQART, steady-state assumptions, and incised volumes are highly correlated. This is supported by our 10Be erosion rates, which are controlled by fault slip and incision rates, and the associated landsliding. Based on a new landslide inventory, we show that erosion rate differences are likely due to differences in incision-related landslide activity across these catchments, and that landslides are a major component of sediment fluxes. From a data set of >13000 grain size counts on hillslope grain size supply and fluvial sediment at catchment outlets, we observe that landslides deliver material 20-200% coarser than other sediment sources, and that this coarse supply has an impact on the grain size distributions being exported from the catchments. Combining our sediment flux and grain size data sets, we are able to show that for our catchments, and potentially also for any areas that respond to changes in climate or tectonics via enhanced landsliding, sediment flux and grain size export increase concomitantly and scale non-linearly. Finally, we explore the consequences that this coupled sediment flux and grain size increase may have on basin stratigraphy, and we show that it has a significant effect on amplifying gravel front progradation.

Quantification Of Erosion Rates Of Agriculturally Used Soils By Artificial

NASA Astrophysics Data System (ADS)

Jha, Abhinand

2010-05-01

0.0.1 1. Introduction to soil erosion measurement by radionuclides Soil erosion by water, wind and tillage affects both agriculture and the natural environment. Studying this phenomenon would be one of the advancements in science. Soil erosion occurs worldwide and since the last two decades it has been a main topic of discussion all over the world. The use of environmental radionuclides such as 90Sr, 137Cs to study medium term soil erosion (40 yrs) started in the early 1990's. Using these new techniques better knowledge about erosion can be gained and this knowledge can be implemented for erosion risk management. The erosion and sedimentation study by using man-made and natural radioisotopes is a key technique, which has developed over the past 30 years. Fallout 137Cs and Cosmogenic 7Be are radionuclides that have been used to provide independent measurements of soil-erosion and sediment-deposition rates and patterns [1] [2] [3] [4]. Erosion measurements using radionuclides 137Cs, 7Be Caesium-137 from atmospheric nuclear-weapons tests in the 1950s and 1960s (Fig.1) is a unique tracer of erosion and sedimentation, since there are no natural sources of 137Cs. Unique events such as the Chernobyl accident in April 1986 caused regional dispersal of 137Cs that affects the total global deposition budget. This yearly pattern of fallout can be used to develop a chronology of deposition horizons in lakes, reservoirs, and floodplains. 137Cs can be easily measured by gamma spectroscopy. Using 137Cs is a fast and cheap method to study erosion-deposition processes compared to the traditional methods like silt bags. PIC Figure 1: Global 137Cs fallout (Modified from SAAS Bulletin 353, Part E, DDR, 1986) When 137Cs, 7Be reach the soil surface by wet and dry deposition, they are quickly and strongly adsorbed by ion exchange and are essentially non exchangeable in most environments. Each radionuclide is distributed differently in the soil because of differences in half-lives (30 yrs for 137Cs and 53 days for 7Be), delivery rates, delivery histories, and land use (Fig. 2). An Physical processes, such as water and wind, are the dominant factors moving 137Cs, 7Be tagged soil particles within and between landscape compartments. PIC Figure 2: Generalized sketch illustrating the distributions of 137Cs and 7Be in tilled and undisturbed soils 2 Erosion study at Young Moraine regions of Germany Recently, a study had been performed to evaluate erosion rates in a typical pattern of landscapes in the Young Moraine regions of North-East Germany [5]. The 137Cs concentrations were measured at selected sampling points of various study sites. Among the areas selected for sampling was Basedow, which is a cultivated area, situated north of Berlin. During a master thesis study at university of Bremen in the academic year 2008-2009 [6] a second sampling campaign was performed at the same study site and 137Cs and 7Be concentrations were measured. Two mathematical models (a proportional model and a mass balance model) were applied to estimate erosion or deposition rates giving a distinction between uncultivated or essentially undisturbed soils and cultivated or soils under permanent pasture (Fig.3A). An improved depositional model was developed during this study. The simulation results from this model are presented in Fig.4. Due to the half-life (53.2 days) of 7Be, a mass balance model was developed and used to calculate erosion rates from 7Be (Fig.3B). PIC Figure 3: A: Erosion rates for 137Cs calculated by mass balance model. B: Erosion rates calculated with mass balance model using the 7Be data at Basedow (2008). The results verify that there is long term erosion as a result of wind, water and agricultural practices. The annual erosion rates at Basedow calculated using a mass balance and a proportional model were in the range between 30-50 t ha-1yr-1. These values were comparable to the erosion rates calculated in the previous study [5] by the models mentioned above. PIC Figure 4: Profiles of sediment calculated for different erosion rates by Cs-137 within the ploughed soil 3 Conclusions and outlook Erosion rates for agricultural soils at Young Moraine regions of North-East Germany were determined by using two radionuclides, 137Cs and 7Be. In combination, the two radionuclides provide a valuable means of investigating soil erosion and assessing erosion risk in the study area. Potentials and limitations of the erosion measurement techniques using radiotracers are discussed in this study. The models used to quantify erosion rates using 137Cs and 7Be were studied. Erosion rates calculated by theses models are difficult to measure over a period of 50 years. A validation of these erosion rates for the time period (50 years) used in the 137Cs-based models will give a new perspective to the use of soil erosion modeling. Most of the regions in India are suffering from high erosion rates [7]. By using the new techniques in erosion quantification the land management practices can be improved and the erosion risk can be reduced in India.

Nitrogen fluxes across hydrogeomorphic zones in coastal deltaic floodplain using flow-through technique

NASA Astrophysics Data System (ADS)

Li, S.; Twilley, R.; Christensen, A.

2017-12-01

Coastal floodplain deltas are the region of continental margins of major river basins that can remove excess nitrogen before entering the coastal ocean. We propose that the processing of nitrogen in active deltaic wetlands varies with soil organic content in response to different hydrogeomorphic zones. Continuous flow-through core system was used to incubate sediment cores from supratidal, intertidal, and subtidal hydrogeomorphic zones along a chronosequence in Wax Lake Delta during summer of 2017. Ambient water from Wax Lake Outlet was continuously pumped through sealed cores to estimate fluxes of inorganic nitrogen and phosphorus across the sediment-water interface by calculating the difference between inflow and outflow concentrations. The average respiration rate of sediment cores from intertidal zone was about 1.5 g m-2 d-1 while the rate in supratidal zone was more than doubled to 3.7 g m-2 d-1. Under the constant inflow concentration of nitrate (about 107.1 umol/L), sediment cores in supratidal zone exhibited greater NO3- uptake (1329.7 umol m-2 h-1) and N2 release (499.0 umol N m-2 h-1) than that in intertidal zone (421.5 umol m-2 h-1 of NO3- uptake and 67.6 umol N m-2 h-1 of N2 flux respectively). These results indicate greater rate of net denitrification in supratidal zone than intertidal zone in the older chronosequence of the active delta (which formed approximately in 1980). Also, lower NH4 flux (mean 70.0 umol m-2 h-1) from sediment to water column in supratidal zone together with higher NO2- flux (mean 94.2 umol m-2 h-1) illustrated strong signal of nitrification. In conclusion, sediment cores at the intertidal zone helped to remove 12% of NO3- from the water column while cores at supratidal zone removed 35% of NO3-. Based on the correlation between NO3- and N2 fluxes, about 60% of NO3- removed could be converted to N2 under sediment organic concentrations of about 12%. Comparisons of NO3 removal and conversion to N2 by denitrification will be compared along the chronosequence to test the effects of shifts from mineral to organic soils as active deltas develop at the mouths of major river basins.

Use of Sediment Budgets for Watershed Erosion Control Planning: A Case Study From Northern California

NASA Astrophysics Data System (ADS)

O'Connor, M.; McDavitt, W.

2002-05-01

Erosion, sedimentation and peak flow increases caused by forest management for commercial timber production may negatively affect aquatic habitat of endangered anadromous fish such as coho salmon ({\\ it O. kisutch}). This paper summarizes a portion of a Watershed Analysis study performed for Pacific Lumber Company, Scotia, CA, focusing on erosion and sedimentation processes and rates and downstream sediment routing and water quality in the Freshwater Creek watershed in northwest California. Hillslope, road and bank erosion, channel sedimentation and sediment rates were quantified using field surveys, aerial photo interpretation, and empirical modeling approaches for different elements of the study. Sediment transport rates for bedload were modeled, and sediment transport rates for suspended sediment were estimated based on size distribution of sediment inputs in relation to sizes transported in suspension. The resulting sediment budget was validated through comparison using recent short-term, high-quality estimates of suspended sediment yield collected by a community watershed group at a downstream monitoring site with technical assistance from the US Forest Service. Another check on the sediment budget was provided by bedload yield data from an adjacent watershed, Jacoby Creek. The sediment budget techniques and bedload routing models used for this study provide sediment yield estimates that are in good agreement with available data. These results suggest that sediment budget techniques that require moderate levels of fieldwork can be used to provide relatively accurate technical assessments for use in the TMDL process. The sediment budget also identifies the most significant sediment sources and suggests a framework within which effective erosion control strategies can be developed.

Landslides and Volcanoes: Fingerprinting Erosional Processes on a tropical island, Dominica, Lesser Antilles

NASA Astrophysics Data System (ADS)

Tomenchok, K.; Hill, M.; Jimerson, C.; Talbot-Wendlandt, , H.; Schmidt, A.; Frey, H. M.

2017-12-01

With 9 active volcanic centers, frequent tropical storms, and widespread landslides, the topography of Dominica is rugged and dynamic. This study aims to fingerprint sediment source dynamics in this relatively unstudied region with fallout radionuclides, clay mineralogy, and acid-extractable grain coating concentration measured in detrital sediments. We also aim to measure basin average erosion rates and determine river incision rates into the underlying ignimbrites. Baseline data on the effects of volcanoes, landslides, land use, and topography in setting erosional dynamics will be established. We sampled outlets of 20 large (>10 km2) rivers as well as 11 points in the Roseau River watershed for a network analysis. Block and ash flows and ignimbrites underlie 89% of the study area. Steep topography (mean slope = 19.6˚) and high levels of rainfall (mean annual rainfall = 1981.41 mm) are consistent throughout the 89% forested island. 934 landslides affect 13% of the study area. We hypothesize that basin average parameters and landslide frequency will correlate with erosion rates and fallout radionuclide activities. In addition, we used topographic data and published ignimbrite ages to calculate river incision rates that ranged from 0.448 - 113.9 mm/yr in the north and 0.86 - 44 mm/yr in the south. Basin average erosion rates will be compared to incision rates to quantify differences between basin wide erosional and river incision processes. We will fingerprint sediment sources with 7Be, 210Pbex, and 137Cs, concentration of grain coatings, and clay mineralogy. We hypothesize that watersheds with erosion from stabilizing landslide scars will have high 7Be, low 210Pbex and 137Cs, low concentrations of grain coatings, and less weathered clays. Watersheds with river bank/scarp erosion or active landslides will have little 7Be, 210Pbex, and 137Cs, less weathered clays, and low concentrations of grain coatings. Watersheds with widespread surface erosion will have high activities, weathered clays, and high concentrations of grain coatings. We will correlate basin average statistics with measured fingerprints to provide a better understanding of sediment source dynamics in an understudied region of the world. With the potential for future landslides, further information will advance hazard mitigation in Dominica.

Calculation and evaluation of sediment effect concentrations for the amphipod Hyalella azteca and the midge Chironomus riparius

USGS Publications Warehouse

Ingersoll, Christopher G.; Haverland, Pamela S.; Brunson, Eric L.; Canfield, Timothy J.; Dwyer, F. James; Henke, Chris; Kemble, Nile E.; Mount, David R.; Fox, Richard G.

1996-01-01

Procedures are described for calculating and evaluating sediment effect concentrations (SECs) using laboratory data on the toxicity of contaminants associated with field-collected sediment to the amphipod Hyalella azteca and the midge Chironomus riparius. SECs are defined as the concentrations of individual contaminants in sediment below which toxicity is rarely observed and above which toxicity is frequently observed. The objective of the present study was to develop SECs to classify toxicity data for Great Lake sediment samples tested with Hyalella azteca and Chironomus riparius. This SEC database included samples from additional sites across the United States in order to make the database as robust as possible. Three types of SECs were calculated from these data: (1) Effect Range Low (ERL) and Effect Range Median (ERM), (2) Threshold Effect Level (TEL) and Probable Effect Level (PEL), and (3) No Effect Concentration (NEC). We were able to calculate SECs primarily for total metals, simultaneously extracted metals, polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). The ranges of concentrations in sediment were too narrow in our database to adequately evaluate SECs for butyltins, methyl mercury, polychlorinated dioxins and furans, or chlorinated pesticides. About 60 to 80% of the sediment samples in the database are correctly classified as toxic or not toxic depending on type of SEC evaluated. ERMs and ERLs are generally as reliable as paired PELs and TELs at classifying both toxic and non-toxic samples in our database. Reliability of the SECs in terms of correctly classifying sediment samples is similar between ERMs and NECs; however, ERMs minimize Type I error (false positives) relative to ERLs and minimize Type II error (false negatives) relative to NECs. Correct classification of samples can be improved by using only the most reliable individual SECs for chemicals (i.e., those with a higher percentage of correct classification). SECs calculated using sediment concentrations normalized to total organic carbon (TOC) concentrations did not improve the reliability compared to SECs calculated using dry-weight concentrations. The range of TOC concentrations in our database was relatively narrow compared to the ranges of contaminant concentrations. Therefore, normalizing dry-weight concentrations to a relatively narrow range of TOC concentrations had little influence on relative concentra of contaminants among samples. When SECs are used to conduct a preliminary screening to predict the potential for toxicity in the absence of actual toxicity testing, a low number of SEC exceedances should be used to minimize the potential for false negatives; however, the risk of accepting higher false positives is increased.

On modeling the paleohydrologic response of closed-basin lakes to fluctuations in climate: Methods, applications, and implications

NASA Astrophysics Data System (ADS)

Liu, Ganming; Schwartz, Franklin W.

2014-04-01

Climate reconstructions using tree rings and lake sediments have contributed significantly to the understanding of Holocene climates. Approaches focused specifically on reconstructing the temporal water-level response of lakes, however, are much less developed. This paper describes a statistical correlation approach based on time series with Palmer Drought Severity Index (PDSI) values derived from instrumental records or tree rings as a basis for reconstructing stage hydrographs for closed-basin lakes. We use a distributed lag correlation model to calculate a variable, ωt that represents the water level of a lake at any time t as a result of integrated climatic forcing from preceding years. The method was validated using both synthetic and measured lake-stage data and the study found that a lake's "memory" of climate fades as time passes, following an exponential-decay function at rates determined by the correlation time lag. Calculated trends in ωt for Moon Lake, Rice Lake, and Lake Mina from A.D. 1401 to 1860 compared well with the established chronologies (salinity, moisture, and Mg/Ca ratios) reconstructed from sediments. This method provides an independent approach for developing high-resolution information on lake behaviors in preinstrumental times and has been able to identify problems of climate signal deterioration in sediment-based climate reconstructions in lakes with a long time lag.

Earthquakes drive large-scale submarine canyon development and sediment supply to deep-ocean basins.

PubMed

Mountjoy, Joshu J; Howarth, Jamie D; Orpin, Alan R; Barnes, Philip M; Bowden, David A; Rowden, Ashley A; Schimel, Alexandre C G; Holden, Caroline; Horgan, Huw J; Nodder, Scott D; Patton, Jason R; Lamarche, Geoffroy; Gerstenberger, Matthew; Micallef, Aaron; Pallentin, Arne; Kane, Tim

2018-03-01

Although the global flux of sediment and carbon from land to the coastal ocean is well known, the volume of material that reaches the deep ocean-the ultimate sink-and the mechanisms by which it is transferred are poorly documented. Using a globally unique data set of repeat seafloor measurements and samples, we show that the moment magnitude ( M w ) 7.8 November 2016 Kaikōura earthquake (New Zealand) triggered widespread landslides in a submarine canyon, causing a powerful "canyon flushing" event and turbidity current that traveled >680 km along one of the world's longest deep-sea channels. These observations provide the first quantification of seafloor landscape change and large-scale sediment transport associated with an earthquake-triggered full canyon flushing event. The calculated interevent time of ~140 years indicates a canyon incision rate of 40 mm year -1 , substantially higher than that of most terrestrial rivers, while synchronously transferring large volumes of sediment [850 metric megatons (Mt)] and organic carbon (7 Mt) to the deep ocean. These observations demonstrate that earthquake-triggered canyon flushing is a primary driver of submarine canyon development and material transfer from active continental margins to the deep ocean.

Earthquakes drive large-scale submarine canyon development and sediment supply to deep-ocean basins

PubMed Central

Mountjoy, Joshu J.; Howarth, Jamie D.; Orpin, Alan R.; Barnes, Philip M.; Bowden, David A.; Rowden, Ashley A.; Schimel, Alexandre C. G.; Holden, Caroline; Horgan, Huw J.; Nodder, Scott D.; Patton, Jason R.; Lamarche, Geoffroy; Gerstenberger, Matthew; Micallef, Aaron; Pallentin, Arne; Kane, Tim

2018-01-01

Although the global flux of sediment and carbon from land to the coastal ocean is well known, the volume of material that reaches the deep ocean—the ultimate sink—and the mechanisms by which it is transferred are poorly documented. Using a globally unique data set of repeat seafloor measurements and samples, we show that the moment magnitude (Mw) 7.8 November 2016 Kaikōura earthquake (New Zealand) triggered widespread landslides in a submarine canyon, causing a powerful “canyon flushing” event and turbidity current that traveled >680 km along one of the world’s longest deep-sea channels. These observations provide the first quantification of seafloor landscape change and large-scale sediment transport associated with an earthquake-triggered full canyon flushing event. The calculated interevent time of ~140 years indicates a canyon incision rate of 40 mm year−1, substantially higher than that of most terrestrial rivers, while synchronously transferring large volumes of sediment [850 metric megatons (Mt)] and organic carbon (7 Mt) to the deep ocean. These observations demonstrate that earthquake-triggered canyon flushing is a primary driver of submarine canyon development and material transfer from active continental margins to the deep ocean. PMID:29546245

Preliminary Nearshore Sedimentation Rate Analysis of the Tuungane Project Northern Mahale Conservation Area, Lake Tanganyika (Tanzania)

NASA Astrophysics Data System (ADS)

Smiley, R. A.; McGlue, M. M.; Yeager, K. M.; Soreghan, M. J.; Lucas, J.; Kimirei, I.; Mbonde, A.; Limbu, P.; Apse, C.

2017-12-01

The combined effects of climate change, overfishing, and sediment pollution are altering Lake Tanganyika's littoral fisheries in profoundly negative ways. One method for conserving critical fish resources and safeguarding biodiversity in Lake Tanganyika is by establishing small-scale nearshore protected zones, which can be administrated by lakeshore villagers organized into beach management units (BMUs). Each BMU endeavors to manage offshore "no-catch" protected zones, prohibit the use of illegal fishing gear, and promote sustainable agriculture that abates erosion in the lake watershed, in order to mitigate sediment pollution in the lake. We adopted a limnogeological approach to assist in characterizing the littoral zone associated with BMUs in the northern Mahale region of Lake Tanganyika (Tanzania), a critical conservation area for the Nature Conservancy's Tuungane Project (https://www.nature.org/ourinitiatives/regions/africa/wherewework/tuungane-project.xml). We hypothesized that BMUs with heavy onshore agricultural activity would experience relatively high offshore sedimentation rates, due to enhanced sediment-laden runoff in the wet season. Such changes are predicted to alter benthic substrates and degrade habitat available for fish spawning. We mapped bathymetry and sediment types along a 29 km2 area of the littoral zone using high-resolution geophysical tools, and assessed short-term sedimentation rates using sediment cores and radionuclide geochronology (210Pb). Initial results from 210Pb analyses show that sedimentation rates at the mud-line ( 85-100 m water depth) are relatively slow but spatially variable in the northern Mahale area. Offshore of the Kalilani village BMU, linear sedimentation rates are 0.50 mm/yr. By contrast, sedimentation rates offshore from the Igualula village BMU are 0.90-1.30 mm/yr. Higher sedimentation rates near Igualula are consistent with greater sediment inputs from the nearby Lagosa River and its watershed, which has been extensively cultivated for oil palm and cassava. Additional sediment cores from the northern Mahale region are presently being analyzed, and 210Pb data from sediment cores associated with the different BMU areas will shed further light on the impacts of land use change on the littoral fisheries.

Catchment sediment flux: a lake sediment perspective on the onset of the Anthropocene?

NASA Astrophysics Data System (ADS)

Chiverrell, Richard

2014-05-01

Definitions of the Anthropocene are varied but from a geomorphological perspective broadly can be described as the interval of recent Earth history during which 'humans have had an 'overwhelming' effect on the Earth system' (Brown et al., 2013). Identifying the switch to a human-dominated geomorphic process regime is actually a challenging process, with in the 'Old World' ramping up of human populations and impacts on earth surface processes since the Neolithic/Mesolithic transition and the onset of agriculture. In the terrestrial realm lakes offer a unique window on changes in human forcing of earth surface processes from a sedimentary flux perspective, because unlike alluvial and hill-slope systems sedimentation is broadly continuous and uninterrupted. Dearing and Jones (2003) showed for a global dataset of lakes a 5-10 fold increase in sediment delivery comparing pre- and post-anthropogenic disturbance. Here sediment records from several lakes in lowland agricultural landscapes are presented to examine the changes in the flux and composition of materials delivered from their catchments. By definition the lakes record the switch to a human dominated system, but not necessary in accelerated sediment accumulation rates with changes in sediment composition equally important. Data from Crose, Hatch and Peckforton Meres, in lowland northwest England are interrogated producing quantitative land-cover reconstructions from pollen spectra calculated using the REVEALS model (Sugita, 2007), geochemical evidence for changes sediment provenance and flux, and 14C and stable Pb pollutant based chronological models detecting changes in sediment accumulation rate. The lake sediment geochemistry points to several phases of heightened human impact within these small agricultural catchments. Following small-in-scale forest cover reductions and limited impacts in terms of sediment flux during the Neolithic, the Bronze to Iron Age saw the first substantial reductions in forest cover and widespread expansions of agriculture. In some cases the catchment responses, for example here detected via dry mass Zr concentrations, were substantial and outstrip later impacts driven by more intensive agriculture e.g. early Medieval, Norman Conquest and 19th century AD. These themes are developed in relation to the concept of an Anthropocene and wider European lake sediment record. References Brown AG, Tooth S, Chiverrell RC, Rose J, Thomas DSG, Wainwright J, Bullard JE, Thorndycraft VR, Aalto R, Downs P. 2013. The Anthropocene: is there a geomorphological case? Earth Surface Processes and Landforms 38: 431-434. Dearing JA, Jones RT. 2003. Coupling temporal and spatial dimensions of global sediment flux through lake and marine sediment records. Global and Planetary Change 39: 147-168. Sugita S. 2007. Theory of quantitative reconstruction of vegetation I: pollen from large sites REVEALS regional vegetation composition. Holocene 17, 2: 229-241.

Do cosmogenic nuclides (10Be, 14C , 21Ne, 26Al) track late Quaternary climate changes on the Altiplano?

NASA Astrophysics Data System (ADS)

Hippe, K.; Kober, F.; Zeilinger, G.; Ivy-Ochs, S.; Kubik, P.; Maden, C.; Wieler, R.

2010-12-01

The high Altiplano plateau is the most prominent element of the Central Andes, separating the Andean Cordilleras between 15° to 22° S. It represents a tectonically quiet, intramontane basin with arid to semi-arid climate, low relief and internal drainage. Throughout the late Quaternary regional climate on the Altiplano repeatedly changed between wet and dry conditions [1]. The influence of climate on the plateau evolution during the Pleistocene/Holocene is unclear, however, as data on erosion processes and rates on the Altiplano are sparse. Here, we present a multiple-nuclide study investigating surface denudation at the eastern Altiplano of Bolivia (16°-17° S) on millennial and longer timescales. The aim is a better understanding of the complex feedback between climate, tectonics and geomorphology on the topographic evolution of the Andes. Catchment-wide denudation (CWD) rates are provided for a 150 km NW-SE transect along the Altiplano edge based on the analyses of cosmogenic 10Be, 26Al, 21Ne and in-situ 14C in river-borne sediment. Single nuclide CWD rates obtained for 10Be, 26Al and 21Ne are similar for all three nuclides and on the order of 3-37 mm/ka. Thus, the calculated denudation rates provide an averaged denudation history dating back at least to the middle Pleistocene. Denudation rates correlate positively with the mean basin hillslope, which is mainly controlled by basin lithology. For most catchments both, the 26Al/10Be ratios and the 21Ne/10Be ratios indicate a complex erosion/exposure history with probably several periods of sediment storage and burial/shielding totalling ~0.5 - 1.2 Ma. Local geomorphology featuring low slopes and low relief, small terraces and local floodplains also suggests that sediment transport might have been periodically ineffective. Concentrations of in-situ produced short-lived 14C are significantly lower than expected from the concentrations of the long-lived and stable cosmogenic nuclides. This would indicate a 30-40 fold increase in denudation rates since ~3000 years, which appears rather unlikely. Hence, the measured in-situ 14C concentrations may actually reflect sediment storage. Partial sediment shielding at ~80-150 cm depth is plausible from field evidence. Due to the fast decay of 14C, such shielding would result in a drop of the 14C concentration from saturation to the measured values already after several 1000 years. Nevertheless, other explanations as incomplete sediment mixing also have to be taken into account. Interestingly, our CWD long-term data agree well with short-term sediment yield data from the Altiplano (5.6-48 mm/ka) [2]. This suggests an overall uniformity in erosional processes and rates throughout the late Quaternary. The agreement between single nuclide denudation rates, despite the complex storage history, also argues for rather long-term steady-state conditions and highlights the insensitivity of long-lived cosmogenic nuclides to low amplitude, short-term variations in climate. References: [1] Plazcek et al. (2006), GSA Bulletin 118, 515-532, [2] Guyot et al. (1992), Lake Titicaca 113-119.

Analytical and sampling constraints in ²¹⁰Pb dating.

PubMed

MacKenzie, A B; Hardie, S M L; Farmer, J G; Eades, L J; Pulford, I D

2011-03-01

²¹⁰Pb dating provides a valuable, widely used means of establishing recent chronologies for sediments and other accumulating natural deposits. The Constant Rate of Supply (CRS) model is the most versatile and widely used method for establishing ²¹⁰Pb chronologies but, when using this model, care must be taken to account for limitations imposed by sampling and analytical factors. In particular, incompatibility of finite values for empirical data, which are constrained by detection limit and core length, with terms in the age calculation, which represent integrations to infinity, can generate erroneously old ages for deeper sections of cores. The bias in calculated ages increases with poorer limit of detection and the magnitude of the disparity increases with age. The origin and magnitude of this effect are considered below, firstly for an idealized, theoretical ²¹⁰Pb profile and secondly for a freshwater lake sediment core. A brief consideration is presented of the implications of this potential artefact for sampling and analysis. Copyright © 2011 Elsevier B.V. All rights reserved.

Field Monitoring Shows Smaller Sediment Deficit to the Louisiana Coast

NASA Astrophysics Data System (ADS)

Sanks, K. M.; Shaw, J.

2017-12-01

Current reports suggest that the Louisiana Coast will undergo significant drowning due to high subsidence rates and low sediment supply. One report suggests that sediment supply is just 30% of the amount necessary to sustain the current land area (Blum & Roberts, 2009). A novel dataset (CRMS) put together by the USGS and Louisiana's Coastal Protection and Restoration Authority provides direct measurements of sediment accumulation, subsidence rates, and sediment characteristics along the Louisiana Coast over the past 10 years (Jankowski et al., 2017). By interpolating bulk density, percent organic matter, and vertical accretion rates across the coast (274 sites), a more accurate estimate of sediment accumulation, both organic and inorganic, can be determined. Preliminary interpolation shows that an average of 53 MT organic and 132 MT inorganic sediment accumulates on coastal marshes each year. Assuming an average 9 mm/yr subsidence rate (Nienhuis et al., 2017) and 3 mm/yr sea-level rise (Blum & Roberts, 2009), this accumulation results in only a 12 MT/yr, or 6.5%, sediment deficit. Assuming a fluvial sediment discharge of 205 MT/yr, 64% of sediment is being trapped on the delta top. Although the sediment load estimates (MT/yr) may be slightly liberal due to interpolation over water, the fraction sediment deficit is unlikely to significantly change. These results suggest that even if current subsidence rates and sea level rise do not change, the gap between accommodation and accumulation may not be as dire as previously thought.

The effect of floating vegetation on denitrification and greenhouse gas production in wetland mesocosms

NASA Astrophysics Data System (ADS)

Jacobs, A. E.; Harrison, J. A.

2012-12-01

Anthropogenic intensification of nitrogen (N) loading to aquatic ecosystems is widespread and can lead to the degradation of these systems. Wetlands are important sites for N removal via denitrification, the microbially mediated reduction of reactive nitrate to inert N2 gas, but they can also produce high levels of greenhouse gases. Floating plants play an important role in encouraging denitrification, since they create low oxygen conditions that may favor denitrification. We investigated whether wetland sediments with floating plant cover had higher denitrification and greenhouse gas production rates than wetland sediments without floating plants. Replicate flow-through mesocosms with wetland sediment and water were constructed in a growth chamber to mimic the wetland where the sediment and water were collected. Mesocosm treatments were covered with floating vegetation (duckweed), an opaque tarp, or no cover to determine how cover type affects denitrification and greenhouse gas production and whether biotic or abiotic factors are likely responsible for observed differences. Denitrification and greenhouse gas production rates were calculated by measuring excess N2 gas, methane, and nitrous oxide concentrations in the water column and measuring the gas exchange rates between the water column and the atmosphere. Gas exchange rates were measured using an inert volatile tracer added to the water column and accumulation of gas in the mesocosm headspace. Additional mesocosm experiments were performed to determine how duckweed-dominated wetland systems respond to nitrogen loading and which mechanism for lowering dissolved oxygen concentrations is important in affecting denitrification under floating vegetation. Mesocosms with floating vegetation had lower dissolved oxygen than no cover or tarp-covered mesocosms, which is consistent with field and literature observations. Water flowing out of the mesocosms had statistically lower total nitrogen and nitrate concentrations compared to inflow water, and calculated denitrification was statistically higher in the floating vegetation treatments compared to the other treatments. Greenhouse gas production, measured in CO2 equivalents for N2O and CH4, was highly variable and not statistically different between the treatments. Denitrification in the tarp covered mesocosms was similar to the no-cover treatment, indicating that biotic effects in the floating vegetation treatment may be important in lowering water column oxygen levels and increasing denitrification. Understanding how floating vegetation affects total nitrogen loss, denitrification, and greenhouse gas production can be used to weigh ecological costs and benefits of different vegetation types, especially in constructed and managed wetlands.

Sediment accumulation in prairie wetlands under a changing climate: The relative roles of landscape and precipitation

USGS Publications Warehouse

Skagen, Susan K.; Burris, Lucy E.; Granfors, Diane A.

2016-01-01

Sediment accumulation threatens the viability and hydrologic functioning of many naturally formed depressional wetlands across the interior regions of North America. These wetlands provide many ecosystem services and vital habitats for diverse plant and animal communities. Climate change may further impact sediment accumulation rates in the context of current land use patterns. We estimated sediment accretion in wetlands within a region renowned for its large populations of breeding waterfowl and migrant shorebirds and examined the relative roles of precipitation and land use context in the sedimentation process. We modeled rates of sediment accumulation from 1971 through 2100 using the Revised Universal Soil Loss Equation (RUSLE) with a sediment delivery ratio and the Unit Stream Power Erosion Deposition model (USPED). These models predicted that by 2100, 21–33 % of wetlands filled completely with sediment and 27–46 % filled by half with sediments; estimates are consistent with measured sediment accumulation rates in the region reported by empirical studies. Sediment accumulation rates were strongly influenced by size of the catchment, greater coverage of tilled landscape within the catchment, and steeper slopes. Conservation efforts that incorporate the relative risk of infilling of wetlands with sediments, thus emphasizing areas of high topographic relief and large watersheds, may benefit wetland-dependent biota.

Dissolution Rates of Biogenic Carbonate Sediments from the Bermuda Platform

NASA Astrophysics Data System (ADS)

Finlay, A. J.; Andersson, A. J.

2016-02-01

The contribution of biogenic carbonate sediment dissolution rates to overall net reef accretion/erosion (under both present and future oceanic pCO2 levels) has been strikingly neglected, despite experimental results indicating that sediment dissolution might be more sensitive to ocean acidification (OA) than calcification. Dissolution of carbonate sediments could impact net reef accretion rates as well as the formation and preservation of valuable marine and terrestrial ecosystems. Bulk sediment dissolution rates of samples from the Bermuda carbonate platform were measured in natural seawater at pCO2 values ranging from approximately 3500 μatm to 9000 μatm. This range of pCO2 levels incorporates values currently observed in porewaters on the Bermuda carbonate platform as well as a potential future increase in porewater pCO2 levels due to OA. Sediment samples from two different stations on the reef platform were analyzed for grain size and mineralogy. Dissolution rates of sediments in the dominant grain size fraction of the platform (500-1000 μm) from both stations ranged between 16.25 and 47.19 (± 0.27 to 0.79) μmoles g-1 hr-1 and are comparable to rates previously obtained from laboratory experiments on other natural carbonate sediments. At a pCO2 of 3500 μatm, rates from both samples were similar, despite their differing mineralogy. However, at pCO2 levels above 3500 μatm, the sediment sample with a greater weight percent of Mg-calcite had slightly higher dissolution rates. Despite many laboratory studies on biogenic carbonate dissolution, a significant disparity still exists between laboratory measurements and field observations. Performing additional controlled, laboratory experiments on natural sediment may help to elucidate the reasons for this disparity.

Paleoclimate of Quaternary Costa Rica: Analysis of Sediment from ODP Site 1242 in the Eastern Tropical Pacific to Explore the Behavior of the Intertropical Convergence Zone (ITCZ) and Oceanic Circulation

NASA Astrophysics Data System (ADS)

Buczek, C. R.; Joseph, L. H.

2017-12-01

Studies of grain size, magnetic fabric, and terrigenous mass accumulation rates (MAR) on oceanic sediment can provide insights into climatic conditions present at or near the time of deposition by helping to delineate changes in rainfall and oceanic circulation intensities. The fairly homogenous hemipelagic nannofossil clays and clayey nannofossil oozes collected in the upper portion of Ocean Drilling Program (ODP) Site 1242 provide a 1.4 million year sediment record from the Cocos Ridge, in relatively shallow waters of the eastern tropical Pacific Ocean, off the coast of present day Central and South America. Information about shifts in rainfall and oceanic circulation provided by this study may be helpful in understanding changes in the location and behavior of the Intertropical Convergence Zone (ITCZ), and/or other climatic factors, in this area during the Pleistocene and Holocene Epochs. Approximately 130 paired side-by-side samples were selected at approximately evenly spaced intervals throughout the uppermost 190 mcd of the core. To obtain terrigenous grain size and MARs, one set of sediment samples was subject to a five-step chemical extraction process to dissolve any oxy-hydroxy coatings, remove the biogenic carbonate and silicate components, and sieve out grains larger than 63 µm. The pre- and post-extraction weights were compared to calculate a terrigenous weight percent (%) from which the terrigenous MAR values were then calculated, with the use of linear sediment rates and dry bulk density measurements determined from shipboard ODP 1242 analyses. Magnetic fabric, or anisotropy of magnetic susceptibility (AMS), was analyzed on a KLY4S-Kappabridge using the second set of samples taken in pmag cubes. Terrigenous MAR values range between 3.1 and 10.9 g/cm2/kyr, while P' (AMS) values range between 1.004 and 1.04 SI. A distinctive trend is noted in both factors, with both exhibiting relatively high initial values that then decrease from the beginning of the record until 1.0-0.8 Ma, and then remain fairly constant (and relatively low) up-core. The initial decline potentially represents a drying of continental climates and a slowing of oceanic currents during the early Pleistocene, possibly due to shifts in the ITCZ or other factors affecting circulation.

Organic carbon mineralization in the Santa Catalina Basin: benthic boundary layer metabolism

NASA Astrophysics Data System (ADS)

Smith, K. L.; Carlucci, A. F.; Jahnke, R. A.; Craven, D. B.

1987-02-01

Organic carbon mineralization rates in the benthic boundary layer (BBL) of the Santa Catalina Basin (1300 m depth) were estimated to identify the primary sites and organisms involved in the turnover of carbon and to compare these rates with the supply of particulate organic matter entering the system from above. Concurrent in situ measurements of macrozooplankton, epibenthic megafauna, and sediment community oxygen consumption, and bacterioplankton and total microbial (microplankton) metabolism were made on 12 dives with DSRV Alvin in November 1984. Pore water and solid phase chemistries, and sediment microbial activity were measured on samples from box cores. Macrozooplankton oxygen consumption, integrated over the 100 m BBL, was 25.8 μmol O 2 m -2 d -1 (0.3 mg C m -2 d -1). Microplankton carbon mineralization rates were 13-29 mg C m -2 d -1 for the BBL with an assimilation efficiency of 80-90%. The estimated oxygen consumption of the dominant population of epibenthic megafauna, Ophiophthalmus normani, at observed densities was 237.8 μmol O 2 m -2 d -1 (2.4 mg C m -2 d -1). Sediment community oxygen consumption was 2776.8 μmol O 2 m -2 d -1 (28.6 mg C m -2 d -1) which is similar to the estimated microbial carbon mineralization estimate for the sediments of 32 mg C m -2 d -1 assuming a 90% assimilation efficiency. These rates were corroborated further by the observed total inorganic carbon pore water gradients from which a mineralization rate of 10-31 mg C m -2 d -1 was estimated. The combined carbon mineralization by the three consumer groups ranged from 25.7 to 63.7 mg C m -2 d -1. For comparison, the oxygen consumption in the BBL based on hydrographic data from the center and sills of the basin was 3.1-20.0 mg C m -2 d -1. Given the large uncertainties in all of the calculations, there was reasonable agreement between these diverse methods of estimating carbon mineralization. The concurrently measured flux of small particulate organic carbon into the BBL using sediment traps was 11.1 ± 2.4 mg C m -2 d -1, providing 17-43% of the estimated carbon mineralized by the three consumer groups.

Modelling the growth Rate of Algal in sediment-laden flow

NASA Astrophysics Data System (ADS)

Li, H.

2017-12-01

Phytoplankton plays an important role as a primary producer in aquatic ecosystems. Fluid dynamics can affect the growth of algae in a number of ways and can be divided into two categories. On the one hand the advection and diffusion processes may disrupt the vertical migration of phytoplankton. On the other hand hydrodynamic effects of sediment suspension which can affect algal growth, by releasing nutrients and reducing light intensity. Natural water generally contains sediment. Therefore, when the flow enters the lake, it will cause a change in the phytoplankton community at the junction. Few people have studied the effects of sediment-laden flows to algal growth rates. In this project, Baiyangdian was chosen as the key research area to study the effect of sediment-laden flow on the growth rate of algae. And we conducted a microcosmic experiment in the laboratory to simulate the effect of sediment-laden flow on the growth rate of algae, and constructed a numerical model for the growth rate of algae in sediment-laden flow.

Microbial Nitrogen Cycling Associated with the Early Diagenesis of Organic Matter in Subseafloor Sediments

NASA Astrophysics Data System (ADS)

Zhao, R.

2015-12-01

The early diagenesis of organic matter is the major energy source of marine sedimentary biosphere and thus controls its population size; however, the vertical distribution of any functional groups along with the diagenesis of organic matter is remained unclear, especially for those microbes involved in nitrogen transformation which serve as a major control on the nitrogen flux between reservoirs. Here we investigated the vertical distributions of various functional groups in five sediment cores retrieved from Arctic Mid-Ocean Ridge (AMOR), with emphasis on the nitrifiers, denitrifiers and anaerobic ammonium oxidizing bacteria (anammox). We observed the clear geochemical zonation associated with organic matter diagenesis in the sediments based on the pore water profiles of oxygen, nitrate, ammonium, manganese and sulfate, with distinct geochemical transition zones at the boundaries of geochemical zones, including oxic-anoxic transition zone (OATZ) and nitrate-manganese reduction zone (NMTZ). Nitrate was produced in surface oxygenated sediments and nitrate consumption mainly took place at the NMTZ, splitted between re-oxidation of ammonium and manganese (II). Abundances of ammonia oxidizers, nitrite oxidizers, and denitrifiers, estimated through quantitative PCR targeting their respective functional genes, generally decrease with depth, but constantly elevated around the OATZ, NMTZ, and manganese-reduction zone as well. Anammox bacteria were only detected around the NMTZ where both nitrate/nitrite and ammonium are available. These depth profiles of functional groups were also confirmed by the community structure profiling by prokaryotic 16S rRNA gene tag pyrosequencing. Cell-specific rates of nitrification and denitrification, calculated from the bulk net reaction rates divided by functional group abundances, were similar to those values from oligotrophic sediments like North Pond and thus suggested that nitrifiers and denitirifiers populations were in maintenance state. This study illustrated the microbial nitrogen transformation accompanying the early diagenesis of organic matter in marine sediments, which scenario might be occurring in a wide range of stratified environments on Earth.

Origin of Slope Failure in the Ursa Region, Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Stigall, J.; Dugan, B.

2008-12-01

We use one-dimensional fluid flow and stability models to predict the evolution of overpressure and stability conditions of IODP Expedition Sites U1322 and U1324 in the Ursa region, northern Gulf of Mexico. Simulations of homogenous mud deposited at 3 and 12 mm/yr for Sites U1322 and U1324, with permeability (k) on the order of 10-17m2 and bulk compressibility of .4 /MPa, predict overpressures up to .45MPa and 1MPa in shallow sediments (<200m below sea floor). With limit equilibrium calculations for an infinite slope, these overpressures equate to a factor of safety (FS) greater than 10 and 4.5 for a internal friction angle of 26° and a seafloor slope of 2°. This implies stability throughout the last 50,000 years. Seismic and core observations, however, document major slope failures that span the entire Ursa region. Permeability in this region is well constrained by laboratory experiments, so we investigate how pulsed (high-to-low) sedimentation rates could have created unstable conditions, FS <1. Models with periods of high sedimentation generate overpressure that create unstable conditions while maintaining the time-averaged sedimentation rates. Other factors which are not possible to simulate in one dimension, such as a complex basin geometry, also influence the conditions that caused the past failures. A two-dimensional model linking lateral flow between the sites with the interpreted geometry from seismic stratigraphy gives a better picture of the flow field and instability within the basin. Asymmetrical loading of permeable sediments could have created a lateral difference in pore pressures which would have driven lateral flow from Site U1324 to Site U1322 where overpressures are higher than our one-dimensional models suggest. We anticipate that two-dimensional models with transient sedimentation patterns will enhance our understanding of flow in marginally stable environments and triggers of slope failures in passive margin systems.

Exposure and effects of sediment-spiked fludioxonil on macroinvertebrates and zooplankton in outdoor aquatic microcosms.

PubMed

Yin, Xiao H; Brock, Theo C M; Barone, Lidia E; Belgers, J Dick M; Boerwinkel, Marie-Claire; Buijse, Laura; van Wijngaarden, René P A; Hamer, Mick; Roessink, Ivo

2018-01-01

Information from effects of pesticides in sediments at an ecosystem level, to validate current and proposed risk assessment procedures, is scarce. A sediment-spiked outdoor freshwater microcosm experiment was conducted with fludioxonil (lipophilic, non-systemic fungicide) to study exposure dynamics and treatment-related responses of benthic and pelagic macroinvertebrates and zooplankton. Besides blank control and solvent control systems the experiment had six different treatment levels (1.7-614mga.s./kg dry sediment) based around the reported 28-d No Observed Effect Concentration (NOEC) for Chironomus riparius (40mga.s./kg dry sediment). Twelve systems were available per treatment of which four were sacrificed on each of days 28, 56 and 84 after microcosm construction. Fludioxonil persisted in the sediment and mean measured concentrations were 53-82% of the initial concentration after 84days. The dissipation rate increased with the treatment level. Also exposure concentrations in overlying water were long-term, with highest concentrations 28days after initiation of the experiment. Sediment-dwelling Oligochaeta and pelagic Rotifera and Cladocera showed the most pronounced treatment-related declines. The most sensitive sediment-dwelling oligochaete was Dero digitata (population NOEC 14.2mga.s./kg dry sediment). The same NOEC was calculated for the sediment-dwelling macroinvertebrate community. The most sensitive zooplankton species was the cladoceran Diaphanosoma brachyurum (NOEC of 1.6μga.s./L in overlying water corresponding to 5.0mga.s./kg dry sediment). At the two highest treatments several rotifer taxa showed a pronounced decrease, while the zooplankton community-level NOEC was 5.6μga.s./L (corresponding to 14.2mga.s./kg dry sediment). Zooplankton taxa calanoid Copepoda and Daphnia gr. longispina showed a pronounced treatment-related increase (indirect effects). Consequently, an assessment factor of 10 to the chronic laboratory NOECs of Chironomus riparius (sediment) and Daphnia magna (water) results in a regulatory acceptable concentration that is sufficiently protective for both the sediment-dwelling and pelagic organisms in the microcosms. Copyright © 2017 Elsevier B.V. All rights reserved.

[Physical essence of erythrocytic sedimentation rate in the gravitation field of the earth].

PubMed

Cherniĭ, A N

2009-01-01

The erythrocytic sedimentation rate method has been long known in medicine and extensively used in laboratory practice in tuberculosis facilities. However, many authors note that the erythrocytic sedimentation rate phenomenon has not clearly understood. By applying the total theory of relativity and quantum mechanics, the author discloses the physical essence of erythrocytic sedimentation in the gravitation field of the Earth.

An overview of the ecological half-life of the 137Cs radioisotope and a determination of radioactivity levels in sediment samples after Chernobyl in the Eastern Black Sea, Turkey

NASA Astrophysics Data System (ADS)

Baltas, Hasan; Sirin, Murat; Dalgic, Goktug; Cevik, Ugur

2018-01-01

A study which determined the activity concentration of 137Cs in sediments contaminated by effluents from the Chernobyl accident which had collected along the coast of the Eastern Black Sea region in Turkey was carried out in 1993. Marine sediment samples were collected in 2015 from the same fifteen sampling points, and the activity concentrations of 226Ra, 232Th, 40K and 137Cs were determined for the sediment samples. The activity concentrations ranged from 10.94-25.95, 12.14-33.05, 265.74-459.89 and 2.08-37.45 Bq kg- 1 for 226Ra, 232Th, 40K and 137Cs respectively. The results showed that there was a steep decline in 137Cs within the sediment at most of the sampling sites from the Eastern Black Sea region during the 22-year period, except for two sites at which the measured levels were much higher. This may be the result of the combined effects of radioactive contaminant entry into this area from rivers, environmental changes and nuclear testing between 1993 and 2015. Furthermore, the ecological half-life (EHL) of the 137Cs radionuclide was estimated for the sediment samples, and radiological hazard parameters such as the absorbed dose rate in air (D), the annual effective dose equivalent (AEDE) and the excess lifetime cancer risk (ELCR) were calculated and compared with the international recommended values. It was shown that these sediments do not present any significant health risk for humans in this area.

Investigating organic matter in Fanno Creek, Oregon, Part 2 of 3: sources, sinks, and transport of organic matter with fine sediment

USGS Publications Warehouse

Keith, Mackenzie K.; Sobieszczyk, Steven; Goldman, Jami H.; Rounds, Stewart A.

2014-01-01

Organic matter (OM) is abundant in Fanno Creek, Oregon, USA, and has been tied to a variety of water-quality concerns, including periods of low dissolved oxygen downstream in the Tualatin River, Oregon. The key sources of OM in Fanno Creek and other Tualatin River tributaries have not been fully identified, although isotopic analyses from previous studies indicated a predominantly terrestrial source. This study investigates the role of fine sediment erosion and deposition (mechanisms and spatial patterns) in relation to OM transport. Geomorphic mapping within the Fanno Creek floodplain shows that a large portion (approximately 70%) of the banks are eroding or subject to erosion, likely as a result of the imbalance caused by anthropogenic alteration. Field measurements of long- and short-term bank erosion average 4.2 cm/year and average measurements of deposition for the watershed are 4.8 cm/year. The balance between average annual erosion and deposition indicates an export of 3,250 metric tons (tonnes, t) of fine sediment to the Tualatin River—about twice the average annual export of 1,880 t of sediment at a location 2.4 km from the creek’s mouth calculated from suspended sediment load regressions from continuous turbidity data and suspended sediment samples. Carbon content from field samples of bank material, combined with fine sediment export rates, indicates that about 29–67 t of carbon, or about 49–116 t of OM, from bank sediment may be exported to the Tualatin River from Fanno Creek annually, an estimate that is a lower bound because it does not account for the mass wasting of organic-rich O and A soil horizons that enter the stream.

Effect of Check Dams on Erosion and Flow Dynamics on Small Semi-Arid Watersheds

NASA Astrophysics Data System (ADS)

Polyakov, V.; Nearing, M.; Nichols, M.; McClaran, M. P.

2012-12-01

Erosion dynamics in semi-arid environments is defined by high magnitude, low frequency rainfalls that produce runoff with high sediment concentration. Check dams were shown to be an effective sedimentation mitigation technique on small watersheds. Constructed of rocks, or other materials placed across the flow and anchored into the bottom and sides of the channel, these barriers produce upstream and downstream effects. By impounding runoff they reduce flow velocity, increase infiltration and allow sediment settling thus decreasing channel slope. Decreased sediment load downstream of the dam may result in accelerated channel scouring. While the effect of check dams on channel stability has been studied extensively their impact on overall watershed sediment balance is not well known. In 2008 a total of 37 loose rock semi permeable check dams were installed on two small (4.0 and 3.1 ha) watersheds located on the alluvial fan of the Santa Rita Mountains in southern Arizona, USA. Each watershed was equipped with high resolution weighing type rain gauge a supercritical flow flume and sediment sampler. Hyetographs, hydrographs, and sediment load data for the watersheds were collected since 1975. The erosion dynamics and flow characteristics following the check dam installation were compared with historical records. The volume of the sediment retained upstream of each dam was calculated through survey. After 4 years the check dams were filled to over 80% of their capacity and no significant increase in downstream scouring has been observed. Maximum 30-min intensity (I30) was overall best predictor variable for total runoff. After check dam installation the number ratio of runoff to rainfall events has been reduced by half. However, runoff peak rates were not significantly effected.

Investigating organic matter in Fanno Creek, Oregon, Part 2 of 3: Sources, sinks, and transport of organic matter with fine sediment

NASA Astrophysics Data System (ADS)

Keith, Mackenzie K.; Sobieszczyk, Steven; Goldman, Jami H.; Rounds, Stewart A.

2014-11-01

Organic matter (OM) is abundant in Fanno Creek, Oregon, USA, and has been tied to a variety of water-quality concerns, including periods of low dissolved oxygen downstream in the Tualatin River, Oregon. The key sources of OM in Fanno Creek and other Tualatin River tributaries have not been fully identified, although isotopic analyses from previous studies indicated a predominantly terrestrial source. This study investigates the role of fine sediment erosion and deposition (mechanisms and spatial patterns) in relation to OM transport. Geomorphic mapping within the Fanno Creek floodplain shows that a large portion (approximately 70%) of the banks are eroding or subject to erosion, likely as a result of the imbalance caused by anthropogenic alteration. Field measurements of long- and short-term bank erosion average 4.2 cm/year and average measurements of deposition for the watershed are 4.8 cm/year. The balance between average annual erosion and deposition indicates an export of 3,250 metric tons (tonnes, t) of fine sediment to the Tualatin River-about twice the average annual export of 1,880 t of sediment at a location 2.4 km from the creek's mouth calculated from suspended sediment load regressions from continuous turbidity data and suspended sediment samples. Carbon content from field samples of bank material, combined with fine sediment export rates, indicates that about 29-67 t of carbon, or about 49-116 t of OM, from bank sediment may be exported to the Tualatin River from Fanno Creek annually, an estimate that is a lower bound because it does not account for the mass wasting of organic-rich O and A soil horizons that enter the stream.

Validity and Agreement between the 28-Joint Disease Activity Score Based on C-Reactive Protein and Erythrocyte Sedimentation Rate in Patients with Rheumatoid Arthritis

PubMed Central

Nielung, Louise; Christensen, Robin; Danneskiold-Samsøe, Bente; Bliddal, Henning; Holm, Christian Cato; Ellegaard, Karen; Slott Jensen, Hanne; Bartels, Else Marie

2015-01-01

Objective. To validate the agreement between the 28-joint disease activity score based on erythrocyte sedimentation rate (DAS28-ESR) and the 28-joint disease activity score based on C-reactive protein (DAS28-CRP) in a group of Danish patients with rheumatoid arthritis (RA). Methods. Data from 109 Danish RA patients initiating biologic treatment were analysed at baseline and following one year of treatment. Participants were retrospectively enrolled from a previous cohort study and were considered eligible for this project if CRP and ESR were measured at baseline and at the follow-up visit. To assess the extent of agreement between the two DAS28 definitions, the “European League Against Rheumatism” (EULAR) response criteria based on each definition were calculated with cross-classification. Weighted Kappa (κ) coefficients were calculated, and Bland-Altman plots were used to illustrate degree of agreement between DAS28 definitions. Results. The 75 eligible patients were classified as EULAR good, moderate, and nonresponders with good agreement (61/75; 81%) between DAS28-CRP and DAS28-ESR (κ = 0.75 (95% CI: 0.63 to 0.88)). Conclusions. According to our findings, DAS28-CRP and DAS28-ESR are interchangeable when assessing RA patients and the two versions of DAS28 are comparable between studies. PMID:25632353

Design of a sediment-monitoring gaging network on ephemeral tributaries of the Colorado River in Glen, Marble, and Grand Canyons, Arizona

USGS Publications Warehouse

Griffiths, Ronald E.; Topping, David J.; Anderson, Robert S.; Hancock, Gregory S.; Melis, Theodore S.

2014-01-01

Management of sediment in rivers downstream from dams requires knowledge of both the sediment supply and downstream sediment transport. In some dam-regulated rivers, the amount of sediment supplied by easily measured major tributaries may overwhelm the amount of sediment supplied by the more difficult to measure lesser tributaries. In this first class of rivers, managers need only know the amount of sediment supplied by these major tributaries. However, in other regulated rivers, the cumulative amount of sediment supplied by the lesser tributaries may approach the total supplied by the major tributaries. The Colorado River downstream from Glen Canyon has been hypothesized to be one such river. If this is correct, then management of sediment in the Colorado River in the part of Glen Canyon National Recreation Area downstream from the dam and in Grand Canyon National Park may require knowledge of the sediment supply from all tributaries. Although two major tributaries, the Paria and Little Colorado Rivers, are well documented as the largest two suppliers of sediment to the Colorado River downstream from Glen Canyon Dam, the contributions of sediment supplied by the ephemeral lesser tributaries of the Colorado River in the lowermost Glen Canyon, and Marble and Grand Canyons are much less constrained. Previous studies have estimated amounts of sediment supplied by these tributaries ranging from very little to almost as much as the amount supplied by the Paria River. Because none of these previous studies relied on direct measurement of sediment transport in any of the ephemeral tributaries in Glen, Marble, or Grand Canyons, there may be significant errors in the magnitudes of sediment supplies estimated during these studies. To reduce the uncertainty in the sediment supply by better constraining the sediment yield of the ephemeral lesser tributaries, the U.S. Geological Survey Grand Canyon Monitoring and Research Center established eight sediment-monitoring gaging stations beginning in 2000 on the larger of the previously ungaged tributaries of the Colorado River downstream from Glen Canyon Dam. The sediment-monitoring gaging stations consist of a downward-looking stage sensor and passive suspended-sediment samplers. Two stations are equipped with automatic pump samplers to collect suspended-sediment samples during flood events. Directly measuring discharge and collecting suspended-sediment samples in these remote ephemeral streams during significant sediment-transporting events is nearly impossible; most significant run-off events are short-duration events (lasting minutes to hours) associated with summer thunderstorms. As the remote locations and short duration of these floods make it prohibitively expensive, if not impossible, to directly measure the discharge of water or collect traditional depth-integrated suspended-sediment samples, a method of calculating sediment loads was developed that includes documentation of stream stages by field instrumentation, modeling of discharges associated with these stages, and automatic suspended-sediment measurements. The approach developed is as follows (1) survey and model flood high-water marks using a two-dimensional hydrodynamic model, (2) create a stage-discharge relation for each site by combining the modeled flood flows with the measured stage record, (3) calculate the discharge record for each site using the stage-discharge relation and the measured stage record, and (4) calculate the instantaneous and cumulative sediment loads using the discharge record and suspended-sediment concentrations measured from samples collected with passive US U-59 samplers and ISCOTM pump samplers. This paper presents the design of the gaging network and briefly describes the methods used to calculate discharge and sediment loads. The design and methods herein can easily be used at other remote locations where discharge and sediment loads are required.

Nitrogen removal in maturation waste stabilisation ponds via biological uptake and sedimentation of dead biomass.

PubMed

Camargo Valero, M A; Mara, D D; Newton, R J

2010-01-01

In this work a set of experiments was undertaken in a pilot-scale WSP system to determine the importance of organic nitrogen sedimentation on ammonium and total nitrogen removals in maturation ponds and its seasonal variation under British weather conditions, from September 2004 to May 2007. The nitrogen content in collected sediment samples varied from 4.17% to 6.78% (dry weight) and calculated nitrogen sedimentation rates ranged from 273 to 2868 g N/ha d. High ammonium removals were observed together with high concentrations of chlorophyll-a in the pond effluent. Moreover, chlorophyll-a had a very good correlation with the corresponding increment of VSS (algal biomass) and suspended organic nitrogen (biological nitrogen uptake) in the maturation pond effluents. Therefore, when ammonium removal reached its maximum, total nitrogen removal was very poor as most of the ammonia taken up by algae was washed out in the pond effluent in the form of suspended solids. After sedimentation of the dead algal biomass, it was clear that algal-cell nitrogen was recycled from the sludge layer into the pond water column. Recycled nitrogen can either be taken up by algae or washed out in the pond effluent. Biological (mainly algal) uptake of inorganic nitrogen species and further sedimentation of dead biomass (together with its subsequent mineralization) is one of the major mechanisms controlling in-pond nitrogen recycling in maturation WSP, particularly when environmental and operational conditions are favourable for algal growth.

Response of a macrotidal estuary to changes in anthropogenic mercury loading between 1850 and 2000.

PubMed

Sunderland, Elsie M; Dalziel, John; Heyes, Andrew; Branfireun, Brian A; Krabbenhoft, David P; Gobas, Frank A P C

2010-03-01

Methylmercury (MeHg) bioaccumulation in marine food webs poses risks to fish-consuming populations and wildlife. Here we develop and test an estuarine mercury cycling model for a coastal embayment of the Bay of Fundy, Canada. Mass budget calculations reveal that MeHg fluxes into sediments from settling solids exceed losses from sediment-to-water diffusion and resuspension. Although measured methylation rates in benthic sediments are high, rapid demethylation results in negligible net in situ production of MeHg. These results suggest that inflowing fluvial and tidal waters, rather than coastal sediments, are the dominant MeHg sources for pelagic marine food webs in this region. Model simulations show water column MeHg concentrations peaked in the 1960s and declined by almost 40% by the year 2000. Water column MeHg concentrations respond rapidly to changes in mercury inputs, reaching 95% of steady state in approximately 2 months. Thus, MeHg concentrations in pelagic organisms can be expected to respond rapidly to mercury loading reductions achieved through regulatory controls. In contrast, MeHg concentrations in sediments have steadily increased since the onset of industrialization despite recent decreases in total mercury loading. Benthic food web MeHg concentrations are likely to continue to increase over the next several decades at present-day mercury emissions levels because the deep active sediment layer in this system contains a large amount of legacy mercury and requires hundreds of years to reach steady state with inputs.

Response of a macrotidal estuary to changes in anthropogenic mercury loading between 1850 and 2000

USGS Publications Warehouse

Sunderl, E.M.; Dalziel, J.; Heyes, A.; Branfireun, B.A.; Krabbenhoft, D.P.; Gobas, F.A.P.C.

2010-01-01

Methylmercury (MeHg) bioaccumulation in marine food webs poses risks to fish-consuming populations and wildlife. Here we develop and test an estuarine mercury cycling model for a coastal embayment of the Bay of Fundy, Canada. Mass budget calculations reveal that MeHg fluxes into sediments from settling solids exceed losses from sediment-to-water diffusion and resuspension. Although measured methylation rates in benthic sediments are high, rapid demethylation results in negligible net in situ production of MeHg. These results suggest that inflowing fluvial and tidal waters, rather than coastal sediments, are the dominant MeHg sources for pelagic marine food webs in this region. Model simulations show water column MeHg concentrations peaked in the 1960s and declined by almost40% by the year 2000. Water column MeHg concentrations respond rapidly to changes in mercury inputs, reaching 95% of steady state in approximately 2 months. Thus, MeHg concentrations in pelagic organisms can be expected to respond rapidly to mercury loading reductions achieved through regulatory controls. In contrast MeHg concentrations in sediments have steadily increased since the onset of industrialization despite recent decreases in total mercury loading. Benthic food web MeHg concentrations are likely to continue to increase over the next several decades at present-day mercury emissions levels because the deep active sediment layer in this system contains a large amount of legacy mercury and requires hundreds of years to reach steady state with inputs. ?? 2010 American Chemical Society.

Radiocesium wash-off associated with soil erosion from various land uses after the Fukushima Dai-ichi NPP accident

NASA Astrophysics Data System (ADS)

Wakiyama, Yoshifumi; Onda, Yuichi; Yoshimura, Kazuya; Kato, Hiroaki; Konoplev, Alexei; Zheleznyak, Mark

2014-05-01

Soil erosion is the initial process which drives radiocesium into the aquatic systems and therefore the quantification of radiocesium wash-off associated with soil erosion is indispensable for mitigating the risks. This study presents two year's observation of soil erosion and radiocesium wash-off to quantify differences in radiocesium behavior in various land uses. Seven runoff plots were established in four landscapes; uncultivated farmland (Farmland A1, Farmland B1), cultivated farmland (Farmland A2, Farmland B2), grassland (Grassland A, Grassland B) and Japanese cedar forest (Forest) in Kawamata town, an area affected by the Fukushima Dai-ichi Nuclear Power Plant accident. The discharged sediments were collected approximately every two weeks. In laboratories, collected sediments were dried and weighed for calculating soil erosion rates (kg m-2) and served for measurements of radiocesium concentration (Bq kg-1) with HPGe detectors. The erosivity factor of the Universal Soil Loss Equation (R-factor: MJ mm ha-1 hr-1 yr-1) was calculated based on the data of precipitation. Standardized soil erosion rates (kg m-2 MJ-1 mm-1 ha hr yr), observed soil erosion rates divided by R-factor, was 1.8 × 10-4 in Farmland A1, 6.0 × 10-4 in Farmland A2, 1.5 × 10-3 in Farmland B1, 8.3 × 10-4 in Farmland B2, 9.6 × 10-6 in Grassland A, 5.9 × 10-6 in Grassland B and 2.3 × 10-6 in Forest. These erosion rates were basically proportional to their vegetation cover of soil surfaces except for cultivated farmlands. Concentrations of Cs-137 in eroded sediments basically depended on the local deposition of Cs-137 and varied enormously with ranging several orders of magnitude in all the landscapes. For the observation period of time decreasing trends in concentrations of Cs-137 in eroded sediments were not obvious. To compare these results with those of Chernobyl, we calculated normalized 'solid' wash-off coefficient (m2 g-1) with dividing the mean total concentration of Cs-137 in sediments by local deposition of Cs-137 (Konoplev et al., 1992). The coefficient was 4.4 × 10-5 in Farmland A1, 1.3 × 10-5 in Farmland A2, 6.4 × 10-5 in Farmland B1, 1.0 × 10-5 in Farmland B2, 2.2 × 10-5 in Grassland A, 1.0 × 10-5 in Grassland B and 8.2 × 10-5 in Forest. High erodibilities and relatively low values of normalized wash-off coefficients in cultivated farmlands can be attributed to the mixing of surface soil by ploughing. These values almost corresponded to those of Chernobyl. It was found that the total 'solid' wash-off coefficient of radiocesium from farmlands is high and for 2 years period of time after the accident reaches 10%. Generally high precipitation in the region and steep slopes promote higher wash-off of radiocesium as compared to the Chernobyl case. Also, normalized wash-off coefficients exhibited relatively less volatility than erodibilities in the landscapes. These results suggest that soil erosion management is crucial for mitigating risks of radiocesium.

Head-of-tide bottleneck of particulate material transport from watersheds to estuaries

NASA Astrophysics Data System (ADS)

Ensign, Scott H.; Noe, Gregory B.; Hupp, Cliff R.; Skalak, Katherine J.

2015-12-01

We measured rates of sediment, C, N, and P accumulation at four floodplain sites spanning the nontidal through oligohaline Choptank and Pocomoke Rivers, Maryland, USA. Ceramic tiles were used to collect sediment for a year and sediment cores were collected to derive decadal sedimentation rates using 137Cs. The results showed highest rates of short- and long-term sediment, C, N, and P accumulation occurred in tidal freshwater forests at the head of tide on the Choptank and the oligohaline marsh of the Pocomoke River, and lowest rates occurred in the downstream tidal freshwater forests in both rivers. Presumably, watershed material was mostly trapped at the head of tide, and estuarine material was trapped in oligohaline marshes. This hydrologic transport bottleneck at the head of tide stores most available watershed sediment, C, N, and P creating a sediment shadow in lower tidal freshwater forests potentially limiting their resilience to sea level rise.

Head-of-tide bottleneck of particulate material transport from watersheds to estuaries

USGS Publications Warehouse

Ensign, Scott H.; Noe, Gregory; Hupp, Cliff R.; Skalak, Katherine

2015-01-01

We measured rates of sediment, C, N, and P accumulation at four floodplain sites spanning the nontidal through oligohaline Choptank and Pocomoke Rivers, Maryland, USA. Ceramic tiles were used to collect sediment for a year and sediment cores were collected to derive decadal sedimentation rates using 137Cs. The results showed highest rates of short- and long-term sediment, C, N, and P accumulation occurred in tidal freshwater forests at the head of tide on the Choptank and the oligohaline marsh of the Pocomoke River, and lowest rates occurred in the downstream tidal freshwater forests in both rivers. Presumably, watershed material was mostly trapped at the head of tide, and estuarine material was trapped in oligohaline marshes. This hydrologic transport bottleneck at the head of tide stores most available watershed sediment, C, N, and P creating a sediment shadow in lower tidal freshwater forests potentially limiting their resilience to sea level rise.

Influence of system controls on the Late Quaternary geomorphic evolution of a rapidly-infilled incised-valley system: The lower Manawatu valley, North Island New Zealand

NASA Astrophysics Data System (ADS)

Clement, Alastair J. H.; Fuller, Ian C.

2018-02-01

The Manawatu incised-valley estuary was rapidly infilled between 12,000-4700 cal. yr BP. A combination of empirical measurements of sedimentation rates, a reconstruction of relative sea-level (RSL) change, and digital elevation models of key surfaces within the Holocene sedimentary fill of the valley were integrated to produce a numerical model to investigate the influence of the system controls of sea-level change, sediment flux, and accommodation space on the rapid infilling history of the palaeo-estuary. The numerical model indicates that sediment flux into the palaeo-estuary was greatest during the Holocene marine transgression between 12,000-8000 years BP. The average rate of sediment deposition in the estuary during this period was 1.0 M m3 yr- 1. This rapid rate of sedimentation was controlled by the rate of accommodation space creation, as regulated by the rate of sea-level rise and the antecedent configuration of the valley. By the time sea levels stabilised c. 7500 cal. yr BP, the palaeo-estuary had been substantively infilled. Limited accommodation space resulted in rapid infilling of the central basin, though sediment flux into the estuary between 7100 and 4500 cal. yr BP was at a lower rate of 234,000 m3 yr- 1. The limited accommodation space also influenced hydrodynamic conditions in the estuarine central basin, driving export of fine-grained sediment from the estuary. Once the accommodation space of the estuarine basin was infilled sediment bypassed the system, with a consequent reduction in the sedimentation rate in the valley. More accurate partitioning of the sources of sediment driving the infilling is necessary to quantify sediment bypassing. Post-depositional lowering of RSL index points from the valley is driven by neotectonics and sediment compaction.

Effects of hillslope gully stabilization on erosion and sediment production in the Torreon Wash watershed, New Mexico, 2009–12

USGS Publications Warehouse

Matherne, Anne Marie; Tillery, Anne C.; Douglas-Mankin, Kyle R.

2018-04-10

Sediment erosion and deposition in two sets of paired (treated and untreated) upland drainages in the Torreon Wash watershed, upper Rio Puerco Basin, New Mexico, were examined over a 3 1/2-year period from spring 2009 through fall 2012. The objective was to evaluate the effectiveness of shallow, loose-stone check dams, or “one-rock dams,” as a hillslope gully erosion stabilization and mitigation method, and its potential for retaining upland eroded soils and decreasing delivery of sediment to lower ephemeral stream channels. Two high-resolution topographic surveys, completed at the beginning and end of the study period, were used to assess the effects of the mitigation measures at paired-drainage sites in both Penistaja Arroyo and Papers Wash watersheds, and at six main-stem-channel cross-section clusters along Penistaja Arroyo and Torreon Wash in the Torreon Wash watershed.For both drainage pairs, the treated drainage had greater sediment aggradation near the channel than the untreated drainage. Erosion was the dominant geomorphic process in the untreated Penistaja Arroyo drainage, whereas aggradation was the dominant process in the other three drainages. For the Penistaja Arroyo paired drainages, the treated site showed a 51-percent increase in area aggraded and 67-percent increase in volume aggraded per area analyzed over the untreated site. Both Papers Wash drainages showed net aggradation, but with similar treatment effect, with the treated site showing a 29-percent increase in area aggraded and 60-percent increase in volume aggraded per area analyzed over the untreated site. In the untreated Penistaja Arroyo drainage, the calculated minimum erosion rate was 0.0055 inches per year (in/yr; 0.14 millimeters per year [mm/yr]), whereas the calculated aggradation rates for the three drainages for which aggradation was the dominant geomorphic process were 0.0063 in/yr (0.16 mm/yr) for the Penistaja Arroyo treated drainage, 0.012 in/yr (0.31 mm/yr) for the Papers Wash untreated drainage, and 0.988 in/yr (2.51 mm/yr) for the Papers Wash treated drainage.Changes in the channel cross section along the main-stem Penistaja Arroyo and Torreon Wash were also examined. Channel-bank slumping and erosion of previously deposited bed material were apparent sources for sediment suspended in ephemeral streamflow. Cross-sectional channel surveys indicated examples of both erosion and deposition along each channel over the study period. Because the drainage area of the treated drainages is small compared to that of the Torreon Wash watershed, the upland mitigation measures would not be expected to measurably affect short-term concentrations of suspended sediment in main-stem channels.One-rock-dam mitigation structures in the upland drainages appear to have resulted in a decrease in sediment delivery to the main-stem channel. One-rock-dam mitigation structures may affect streamflow through their influence on runoff volume (via infiltration) and runoff rate (via detention), both of which may vary with time after structure installation.

A pre-dam-removal assessment of sediment transport for four dams on the Kalamazoo River between Plainwell and Allegan, Michigan

USGS Publications Warehouse

Syed, Atiq U.; Bennett, James P.; Rachol, Cynthia M.

2005-01-01

Four dams on the Kalamazoo River between the cities of Plainwell and Allegan, Mich., are in varying states of disrepair. The Michigan Department of Environmental Quality (MDEQ) and U.S. Environmental Protection Agency (USEPA) are considering removing these dams to restore the river channels to pre-dam conditions. This study was initiated to identify sediment characteristics, monitor sediment transport, and predict sediment resuspension and deposition under varying hydraulic conditions. The mathematical model SEDMOD was used to simulate streamflow and sediment transport using three modeling scenarios: (1) sediment transport simulations for 730 days (Jan. 2001 to Dec. 2002), with existing dam structures, (2) sediment transport simulations based on flows from the 1947 flood at the Kalamazoo River with existing dam structures, and (3) sediment transport simulations based on flows from the 1947 flood at the Kalamazoo River with dams removed. Sediment transport simulations based on the 1947 flood hydrograph provide an estimate of sediment transport rates under maximum flow conditions. These scenarios can be used as an assessment of the sediment load that may erode from the study reach at this flow magnitude during a dam failure. The model was calibrated using suspended sediment as a calibration parameter and root mean squared error (RMSE) as an objective function. Analyses of the calibrated model show a slight bias in the model results at flows higher than 75 m3/s; this means that the model-simulated suspended-sediment transport rates are higher than the observed rates; however, the overall calibrated model results show close agreement between simulated and measured values of suspended sediment. Simulation results show that the Kalamazoo River sediment transport mechanism is in a dynamic equilibrium state. Model results during the 730-day simulations indicate significant sediment erosion from the study reach at flow rates higher than 55 m3/s. Similarly, significant sediment deposition occurs during low to average flows (monthly mean flows between 25.49 m3/s and 50.97 m3/s) after a high-flow event. If the flow continues to stay in the low to average range the system shifts towards equilibrium, resulting in a balancing effect between sediment deposition and erosion rates. The 1947 flood-flow simulations show approximately 30,000 m3 more instream sediments erosion for the first 21 days of the dams removed scenario than for the existing-dams scenario, with the same initial conditions for both scenarios. Application of a locally weighted regression smoothing (LOWESS) function to simulation results of the dams removed scenario indicates a steep downtrend with high sediment transport rates during the first 21 days. In comparison, the LOWESS curve for the existing-dams scenario shows a smooth transition of sediment transport rates in response to the change in streamflow. The high erosion rates during the dams-removed scenario are due to the absence of the dams; in contrast, the presence of dams in the existing-dams scenario helps reduce sediment erosion to some extent. The overall results of 60-day simulations for the 1947 flood show no significant difference in total volume of eroded sediment between the two scenarios, because the dams in the study reach have low heads and no control gates. It is important to note that the existing-dams and dams-removed scenarios simulations are run for only 60 days; therefore, the simulations take into account the changes in sediment erosion and deposition rates only during that time period. Over an extended period, more erosion of instream sediments would be expected to occur if the dams are not properly removed than under the existing conditions. On the basis of model simulations, removal of dams would further lower the head in all the channels. This lowering of head could produce higher flow velocities in the study reach, which ultimately would result in accelerated erosion rates.

Efficiencies of forestry best management practices for reducing sediment and nutrient losses in the eastern United States

Treesearch

Pamela Edwards; Karl W.J. Williard

2010-01-01

Quantifying the effects of forestry best management practices (BMPs) on sediment and nutrient loads is a critical need. Through an exhaustive literature search, three paired forested watershed studies in the eastern United States were found that permitted the calculation of BMP efficiencies--the percent reduction in sediment or nutrients achieved by BMPs. For sediment...

Historical record of mercury contamination in sediments from the Babeni Reservoir in the Olt River, Romania.

PubMed

Bravo, Andrea Garcia; Loizeau, Jean-Luc; Ancey, Lydie; Ungureanu, Viorel Gheorghe; Dominik, Janusz

2009-08-01

Mercury (Hg) is a ubiquitous and hazardous contaminant in the aquatic environment showing a strong biomagnification effect along the food chain. The most common transfer path of Hg to humans is contaminated fish consumption. In severely exposed humans, Hg poisoning may lead to damage in the central nervous system. Thus, it is important to examine current and past contamination levels of Hg in aquatic milieu. The Olt River is the largest Romanian tributary of the Danube River. The use of Hg as an electrode in a chlor-alkali plant contributed to the contamination of the aquatic environment in the Rm Valcea region. The purpose of this study was to compare the current state of Hg contamination with the past contamination using a historical record obtained from a dated sediment core from one of the Olt River reservoirs (Babeni) located downstream from the chlor-alkali plant. To our knowledge, no published data on Hg contamination in this region are available. The Babeni Reservoir was selected for this study because it is situated downstream from the chlor-alkali plant, whilst the other reservoirs only retain the pollutants coming from the upstream part of the watershed. Preliminary analyses (unpublished) showed high Hg concentrations in the surface sediment of the Babeni Reservoir. One core was taken in the upstream Valcea Reservoir to provide a local background level of Hg concentrations in sediments. Sediment texture was uniform in the cores from both reservoirs. Laminated sediment structure, without any obvious discontinuities, was observed. Hg concentrations in the sediment core from the Valcea Reservoir were low and constant (0.01-0.08 mg/kg). In Babeni Reservoir sediments, Hg concentrations were very high in the deeper core section (up to 45 mg/kg in the longest core) and decreased to lower concentrations toward the top of the cores (1.3-2.4 mg/kg). This decrease probably reflects technological progress in control of emissions from the Hg-cell-based chlor-alkali industry. Two strong peaks could be distinguished in older sediments. The mean rate of sedimentation (5.9 cm/year) was calculated from the depth of the (137)Cs Chernobyl peak. This was in good agreement with the sedimentation rate estimated at this site from a bathymetric study. Assuming a constant sedimentation rate, the two Hg peaks would reflect two contamination events in 1987 and 1991, respectively. However, it is also possible that the two peaks belong to the same contamination event in 1987 but were separated by a sediment layer richer in sand and silt. This layer had a low Hg concentration, which can be interpreted as a mass deposition event related to a major flood bringing Hg-free sediments. Whilst the chlor-alkali plant partly switched to a cleaner technology in 1999, no obvious decrease of Hg concentrations was observed in recent decade. Results from the sediment core reflected the historical trend of Hg release from the chlor-alkali plant, revealed important contamination episodes and confirmed a legacy of contamination of Hg in recent sediments even if the concentrations of Hg decreased toward the surface due to a more efficient emission control. Although the Hg concentrations in Babeni Reservoir sediments were extremely high in the late eighties and they remain one order of magnitude higher in the surface sediments than in sediments from the upstream reservoir, little is known about the transfer of Hg to the biota and human population. Our initial measurements indicate the presence of monomethyl-Hg (MMHg) in pore water, but further studies are necessary to evaluate fluxes of MMHg at the sediment-water interface. Samples of fish and hair from various groups of the local population were recently collected to evaluate the potential hazard of Hg contamination to human health in the Rm Valcea region.

Sediment Dynamics Within Buffer Zone and Sinkhole Splay Areas Under Extreme Soil Disturbance Conditions.

PubMed

Schoonover, Jon E; Crim, Jackie F; Williard, Karl W J; Groninger, John W; Zaczek, James J; Pattumma, Klairoong

2015-09-01

Sedimentation dynamics were assessed in sinkholes within training areas at Ft. Knox Military Installation, a karst landscape subjected to decades of tracked vehicle use and extreme soil disturbance. Sinkholes sampled were sediment-laden and behaved as intermittent ponds. Dendrogeomorphic analyses were conducted using willow trees (Salix spp.) located around the edge of 18 sinkholes to estimate historical sedimentation rates, and buried bottles were installed in 20 sinkholes at the center, outer edge, and at the midpoint between the center and edge to estimate annual sedimentation rates. Sedimentation data were coupled with vegetation characteristics of sinkhole buffers to determine relationships among these variables. The dendrogeomorphic method estimated an average accumulation rate of 1.27 cm year(-1) translating to a sediment loss rate of 46.1 metric ton year(-1) from the training areas. However, sediment export to sinkholes was estimated to be much greater (118.6 metric ton year(-1)) via the bottle method. These data suggest that the latter method provided a more accurate estimate since accumulation was greater in the center of sinkholes compared to the periphery where dendrogeomorphic data were collected. Vegetation data were not tightly correlated with sedimentation rates, suggesting that further research is needed to identify a viable proxy for direct measures of sediment accumulation in this extreme deposition environment. Mitigation activities for the sinkholes at Ft. Knox's tank training area, and other heavily disturbed karst environments where extreme sedimentation exists, should consider focusing on flow path and splay area management.

Kinetic and microbial community analysis of methyl ethyl ketone biodegradation in aquifer sediments.

PubMed

Fahrenfeld, N; Pruden, A; Widdowson, M

2017-02-01

Methyl ethyl ketone (MEK) is a common groundwater contaminant often present with more toxic compounds of primary interest. Because of this, few studies have been performed to determine the effect of microbial community structure on MEK biodegradation rates in aquifer sediments. Here, microcosms were prepared with aquifer sediments containing MEK following a massive spill event and compared to laboratory-spiked sediments, with MEK biodegradation rates quantified under mixed aerobic/anaerobic conditions. Biodegradation was achieved in MEK-contaminated site sediment microcosms at about half of the solubility (356 mg/L) with largely Firmicutes population under iron-reducing conditions. MEK was biodegraded at a higher rate [4.0 ± 0.74 mg/(L days)] in previously exposed site samples compared to previously uncontaminated sediments [0.51 ± 0.14 mg/(L days)]. Amplicon sequencing and denaturing gradient gel electrophoresis of 16S rRNA genes were combined to understand the relationship between contamination levels, biodegradation, and community structure across the plume. More heavily contaminated sediments collected from an MEK-contaminated field site had the most similar communities than less contaminated sediments from the same site despite differences in sediment texture. The more diverse microbial community observed in the laboratory-spiked sediments reduced MEK concentration 47 % over 92 days. Results of this study suggest lower rates of MEK biodegradation in iron-reducing aquifer sediments than previously reported for methanogenic conditions and biodegradation rates comparable to previously reported nitrate- and sulfate-reducing conditions.

An In situ Study of Seasonal Dissolved Organic Carbon and Nutrient Fluxes from a Spartina alterniflora Salt Marsh in North Carolina

NASA Astrophysics Data System (ADS)

Detweiler, D. J.; Loh, A. N.

2016-02-01

Spartina alterniflora salt marshes are among the most productive and biogeochemically active ecosystems on Earth. While they have been shown to be sources of dissolved organic carbon (DOC) and nutrient export to the coastal ocean via tidal processes, it has not been well quantified experimentally. The purpose of this study was to quantify DOC and nutrient fluxes from a fringing S. alterniflora salt marsh in North Carolina. The experiment was conducted using in situ benthic microcosm chambers filled with seawater during a flooding tide; the chambers were then plugged, and samples were collected during an ebbing tide over the course of 270 minutes while simulating light and dark conditions. Water samples were filtered and analyzed for DOC and nutrient concentrations over time and used to calculate fluxes from vegetated (S. alterniflora) and non-vegetated marsh sediments. Preliminary daily flux calculations show that fluxes from vegetated sediments have a higher magnitude when compared to fluxes from non-vegetated sediments. Daily flux calculations also suggest that vegetated sediments act as a DOC source while non-vegetated sediments act as a DOC sink. Additional flux data for dissolved inorganic and organic nitrogen (DIN, DON) and dissolved inorganic and organic phosphorus (DIP, DOP) as well as marsh sediment characterization will also be presented. Ultimately, these data will provide seasonal daily flux calculations for S. alterniflora salt marshes and insight as to how changing environmental conditions such as wetland modification, wetland destruction, nutrient input, and climate change are affecting coastal biogeochemical cycles.

The U.S. Department of Energy's Regulatory and Evaluation Framework for Demonstrating Radiation Protection of the Environment: Implementation at the Hanford Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antonio, Ernest J.; Tiller, Brett L.; Domotor, S. L.

2005-08-01

Abstract. In 2001, a multi-agency study was conducted to characterize potential environmental effects from radiological and chemical contaminants on the near-shore environment of the Columbia River at the 300 Area of the U.S. Department of Energy’s Hanford Site. Historically, the 300 Area was the location of nuclear fuel fabrication and was the main location for research and development activities from the 1940s until the late 1980s. During past waste handling practices uranium, copper, and other heavy metals were routed to liquid waste streams and ponds near the Columbia River shoreline. The Washington State Department of Health and the Pacific Northwestmore » National Laboratory’s Surface Environmental Surveillance Project sampled various environmental components including river water, riverbank spring water, sediment, fishes, crustaceans, bivalve mollusks, aquatic insects, riparian vegetation, small mammals, and terrestrial invertebrates for analyses of radiological and chemical constituents. The radiological analysis results for water and sediment were used as initial input into the RESRAD BIOTA. The RESRAD BIOTA code showed that maximum radionuclide concentrations measured in water and sediment were lower than the initial screening criteria for concentrations to produce dose rates at existing or proposed limits. Radionuclide concentrations measured in biota samples were used to calculate site-specific bioaccumulation coefficients (Biv) to test the utility of the RESRAD BIOTA’s site-specific screening phase. To further evaluate site-specific effects, the default Relative Biological Effect (RBE) for internal alpha particle emissions was reduced by half and the program’s kinetic/allometric calculation approach was initiated. The subsequent calculations showed the initial RESRAD BIOTA results to be conservative, which is appropriate for screening purposes.« less

Natural and Anthropogenic Causes of Accelerated Sediment Accumulation Rates in Nehalem Bay Salt Marshes, Oregon

NASA Astrophysics Data System (ADS)

Molino, G. D.; Wheatcroft, R. A.; Peck, E. K.; Brophy, L.

2016-12-01

Vertical sediment accretion in estuarine salt marshes occurs as sediments settle out of the water column and onto marsh soils during periods of tidal inundation - thus accretion is influenced by both relative sea level rise (RSLR) and sediment flux to the estuary. Oregon estuaries are understudied compared to their East and Gulf Coast counterparts, but provide a unique opportunity to disentangle these effects. A broader study in three Oregon estuaries (Peck et al., this session) indicates RSLR as the dominant factor controlling sedimentation rates. Working in Nehalem Bay (northern Oregon coast), replicate sediment cores were taken along several transects across an elevation gradient for analysis of sediment and carbon accumulation using CT scans, gamma detection of Pb-210, X-Ray Fluorescence (XRF) and Loss-on-Ignition (LOI). Preliminary results indicate sediment accumulation rates over the past century are higher than rates seen in other comparable Oregon salt marshes; this is consistent with past studies and preliminary analysis of remote sensing data that show significant horizontal expansion of Nehalem marshes. A number of possible causes for the high sediment accumulation rates - hydroclimate of Nehalem River, extensive timber harvesting, forest fires such as the so-called Tillamook Burns, and diking of adjacent marshes - are being explored.

Sediment Budgets and Sources Inform a Novel Valley Bottom Restoration Practice Impacted by Legacy Sediment: The Big Spring Run, PA, Restoration Experiment

NASA Astrophysics Data System (ADS)

Walter, R. C.; Merritts, D.; Rahnis, M. A.; Gellis, A.; Hartranft, J.; Mayer, P. M.; Langland, M.; Forshay, K.; Weitzman, J. N.; Schwarz, E.; Bai, Y.; Blair, A.; Carter, A.; Daniels, S. S.; Lewis, E.; Ohlson, E.; Peck, E. K.; Schulte, K.; Smith, D.; Stein, Z.; Verna, D.; Wilson, E.

2017-12-01

Big Spring Run (BSR), a small agricultural watershed in southeastern Pennsylvania, is located in the Piedmont Physiographic Province, which has the highest nutrient and sediment yields in the Chesapeake Bay watershed. To effectively reduce nutrient and sediment loading it is important to monitor the effect of management practices on pollutant reduction. Here we present results of an ongoing study, begun in 2008, to understand the impact of a new valley bottom restoration strategy for reducing surface water sediment and nutrient loads. We test the hypotheses that removing legacy sediments will reduce sediment and phosphorus loads, and that restoring eco-hydrological functions of a buried Holocene wetland (Walter & Merritts 2008) will improve surface and groundwater quality by creating accommodation space to trap sediment and process nutrients. Comparisons of pre- and post-restoration gage data show that restoration lowered the annual sediment load by at least 118 t yr-1, or >75%, from the 1000 m-long restoration reach, with the entire reduction accounted for by legacy sediment removal. Repeat RTK-GPS surveys of pre-restoration stream banks verified that >90 t yr-1 of suspended sediment was from bank erosion within the restoration reach. Mass balance calculations of 137Cs data indicate 85-100% of both the pre-restoration and post-restoration suspended sediment storm load was from stream bank sources. This is consistent with trace element data which show that 80-90 % of the pre-restoration outgoing suspended sediment load at BSR was from bank erosion. Meanwhile, an inventory of fallout 137Cs activity from two hill slope transects adjacent to BSR yields average modern upland erosion rates of 2.7 t ha-1 yr-1 and 5.1 t ha-1 yr-1, showing modest erosion on slopes and deposition at toe of slopes. We conclude that upland farm slopes contribute little soil to the suspended sediment supply within this study area, and removal of historic valley bottom sediment effectively reduced bank erosion and sediment and phosphorus loads. Enhanced deposition further contributed to load reductions; prior to restoration, there was no deposition on tile pads on the 1.5 m-high legacy sediment "floodplain" terrace, whereas after restoration deposition on the low, restored floodplain showed net accumulation of 0.009 ± 0.012 m yr-1.

D:L-Amino Acid Modeling Reveals Fast Microbial Turnover of Days to Months in the Subsurface Hydrothermal Sediment of Guaymas Basin.

PubMed

Møller, Mikkel H; Glombitza, Clemens; Lever, Mark A; Deng, Longhui; Morono, Yuki; Inagaki, Fumio; Doll, Mechthild; Su, Chin-Chia; Lomstein, Bente A

2018-01-01

We investigated the impact of temperature on the microbial turnover of organic matter (OM) in a hydrothermal vent system in Guaymas Basin, by calculating microbial bio- and necromass turnover times based on the culture-independent D:L-amino acid model. Sediments were recovered from two stations near hydrothermal mounds (<74°C) and from one cold station (<9°C). Cell abundance at the two hydrothermal stations dropped from 10 8 to 10 6 cells cm -3 within ∼5 m of sediment depth resulting in a 100-fold lower cell number at this depth than at the cold site where numbers remained constant at 10 8 cells cm -3 throughout the recovered sediment. There were strong indications that the drop in cell abundance was controlled by decreasing OM quality. The quality of the sedimentary OM was determined by the diagenetic indicators %T AA C (percentage of total organic carbon present as amino acid carbon), %T AA N (percentage of total nitrogen present as amino acid nitrogen), aspartic acid:β-alanine ratios, and glutamic acid:γ-amino butyric acid ratios. All parameters indicated that the OM became progressively degraded with increasing sediment depth, and the OM in the hydrothermal sediment was more degraded than in the uniformly cold sediment. Nonetheless, the small community of microorganisms in the hydrothermal sediment demonstrated short turnover times. The modeled turnover times of microbial bio- and necromass in the hydrothermal sediments were notably faster (biomass: days to months; necromass: up to a few hundred years) than in the cold sediments (biomass: tens of years; necromass: thousands of years), suggesting that temperature has a significant influence on the microbial turnover rates. We suggest that short biomass turnover times are necessary for maintance of essential cell funtions and to overcome potential damage caused by the increased temperature.The reduced OM quality at the hyrothemal sites might thus only allow for a small population size of microorganisms.

Magnetic properties as tracers for source-to-sink dispersal of sediments: A case study in the Taiwan Strait

NASA Astrophysics Data System (ADS)

Horng, Chorng-Shern; Huh, Chih-An

2011-09-01

Different lithologies between Taiwan and southeastern China lead to diverse mineralogical composition for weathering products derived from the two shores of the Taiwan Strait. Pyrrhotite and magnetite are respectively the dominant magnetic minerals associated with fluvial sediments from western Taiwan and southeastern China. While magnetite commonly co-exists with pyrrhotite in sediments sourced from Taiwan, pyrrhotite has not been found in sediments sourced from mainland China. Associated with such a distinction are vast differences in magnetic properties, including magnetic susceptibility (χ), SIRM, HIRM and the S-ratio, which can be used to study the provenances of sediments in the Taiwan Strait and adjoining marginal seas. Based on any two of these parameters, the magnetic characteristics of much of the Taiwan Strait sediment can be explained using a two-endmember mixing model. Source-to-sink dispersal of sediments in the Taiwan Strait can then be traced from the distribution of these parameters. The results not only corroborate an earlier study based on radionuclides and particle size distribution ( Huh et al., 2011) but reveal more diagnostic details. Besides spatial distribution based on a large number (216) of surface sediments, we also analyzed temporal variation of magnetic properties in six well-dated cores collected at key sites along the sediment source-to-sink pathways. From profiles of these parameters in cores from the middle of the northern Taiwan Strait, it is calculated that sediment supply from Taiwan has increased substantially in the past five decades, which may very well be related to accelerated land use and increased frequency of intense rainfalls in Taiwan during the same period. The approach described in this work may be extended to other source-to-sink systems around the world and through time, especially the mountainous islands fringing the Pacific and Indian Oceans in southeastern Asia. As with Taiwan, these islands have high denudation rates and pyrrhotite is in all likelihood a mineral characteristic of their metamorphic terrains.

Benthic phosphorus regeneration in the Potomac River Estuary

USGS Publications Warehouse

Callender, E.

1982-01-01

The flux of dissolved reactive phosphate from Potomac riverine and estuarine sediments is controlled by processes occurring at the water-sediment interface and within surficial sediment. In situ benthic fluxes (0.1 to 2.0 mmoles m-2 day-1) are generally five to ten times higher than calculated diffusive fluxes (0.020 to 0.30 mmoles m-2 day-1). The discrepancy between the two flux estimates is greatest in the transition zone (river mile 50 to 70) and is attributd to macrofaunal irrigation. Both in situ and diffusive fluxes of dissolved reactive phosphate from Potomac tidal river sediments are low while those from anoxic lower estuarine sediments are high. The net accumulation rate of phosphorus in benthic sediment exhibits an inverse pattern. Thus a large fraction of phosphorus is retained by Potomac tidal river sediments, which contain a surficial oxidized layer and oligochaete worms tolerant of low oxygen conditions, and a large fraction of phosphorus is released from anoxic lower estuary sediments. Tidal river sediment pore waters are in equilibrium with amorphous Fe (OH)3 while lower estuary pore waters are significantly undersaturated with respect to this phase. Benthic regeneration of dissolved reactive phosphorus is sufficient to supply all the phosphorus requirements for net primary production in the lower tidal river and transition-zone waters of the Potomac River Estuary. Benthic regeneration supplies approximately 25% as much phosphorus as inputs from sewage treatment plants and 10% of all phosphorus inputs to the tidal Potomac River. When all available point source phosphorus data are put into a steady-state conservation of mass model and reasonable coefficients for uptake of dissolved phosphorus, remineralization of particulate phosphorus, and sedimentation of particulate phosphorus are used in the model, a reasonably accurate simulation of dissolved and particulate phosphorus in the water column is obtained for the summer of 1980. ?? 1982 Dr W. Junk Publishers.

Contemporary deposition and long-term accumulation of sediment and nutrients by tidal freshwater forested wetlands impacted by sea level rise

USGS Publications Warehouse

Noe, Gregory; Hupp, Cliff R.; Bernhardt, Christopher E.; Krauss, Ken W.

2016-01-01

Contemporary deposition (artificial marker horizon, 3.5 years) and long-term accumulation rates (210Pb profiles, ~150 years) of sediment and associated carbon (C), nitrogen (N), and phosphorus (P) were measured in wetlands along the tidal Savannah and Waccamaw rivers in the southeastern USA. Four sites along each river spanned an upstream-to-downstream salinification gradient, from upriver tidal freshwater forested wetland (TFFW), through moderately and highly salt-impacted forested wetlands, to oligohaline marsh downriver. Contemporary deposition rates (sediment, C, N, and P) were greatest in oligohaline marsh and lowest in TFFW along both rivers. Greater rates of deposition in oligohaline and salt-stressed forested wetlands were associated with a shift to greater clay and metal content that is likely associated with a change from low availability of watershed-derived sediment to TFFW and to greater availability of a coastal sediment source to oligohaline wetlands. Long-term accumulation rates along the Waccamaw River had the opposite spatial pattern compared to contemporary deposition, with greater rates in TFFW that declined to oligohaline marsh. Long-term sediment and elemental mass accumulation rates also were 3–9× lower than contemporary deposition rates. In comparison to other studies, sediment and associated nutrient accumulation in TFFW are lower than downriver/estuarine freshwater, oligohaline, and salt marshes, suggesting a reduced capacity for surface sedimentation (short-term) as well as shallow soil processes (long-term sedimentation) to offset sea level rise in TFFW. Nonetheless, their potentially large spatial extent suggests that TFFW have a large impact on the transport and fate of sediment and nutrients in tidal rivers and estuaries.

Trend analyses with river sediment rating curves

USGS Publications Warehouse

Warrick, Jonathan A.

2015-01-01

Sediment rating curves, which are fitted relationships between river discharge (Q) and suspended-sediment concentration (C), are commonly used to assess patterns and trends in river water quality. In many of these studies it is assumed that rating curves have a power-law form (i.e., C = aQb, where a and b are fitted parameters). Two fundamental questions about the utility of these techniques are assessed in this paper: (i) How well to the parameters, a and b, characterize trends in the data? (ii) Are trends in rating curves diagnostic of changes to river water or sediment discharge? As noted in previous research, the offset parameter, a, is not an independent variable for most rivers, but rather strongly dependent on b and Q. Here it is shown that a is a poor metric for trends in the vertical offset of a rating curve, and a new parameter, â, as determined by the discharge-normalized power function [C = â (Q/QGM)b], where QGM is the geometric mean of the Q values sampled, provides a better characterization of trends. However, these techniques must be applied carefully, because curvature in the relationship between log(Q) and log(C), which exists for many rivers, can produce false trends in â and b. Also, it is shown that trends in â and b are not uniquely diagnostic of river water or sediment supply conditions. For example, an increase in â can be caused by an increase in sediment supply, a decrease in water supply, or a combination of these conditions. Large changes in water and sediment supplies can occur without any change in the parameters, â and b. Thus, trend analyses using sediment rating curves must include additional assessments of the time-dependent rates and trends of river water, sediment concentrations, and sediment discharge.

The contribution of sediment from forested areas of the Chesapeake Bay Watershed

NASA Astrophysics Data System (ADS)

Gellis, A.; Brakebill, J.

2012-12-01

Fine-grained sediment is a major pollutant in the Chesapeake Bay and its receiving waters. Sediment budget studies have been conducted in small basins draining to the Bay over the last decade to understand the important sources of fine-grained sediment, quantify erosion rates, and determine sediment yields. Sediment budget approaches include modeling (SPARROW), sediment fingerprinting, and quantifying upland rates of erosion (Cesium-137). SPARROW model results indicate that forests deliver between 2 to 8% of the total sediment to the Bay. Sediment-fingerprinting results from small watershed studies indicate that forests contribute between 13 to 29 % of the sediment. The Cesium-137 technique was used to quantify soil redistribution (erosion and deposition) rates for forested areas in the Linganore Creek (146 km2) watershed which drains the Piedmont Physiographic Province. Average forest erosion rates measured in 2009 for Linganore Creek using Cesium-137 were 2.6 t/ha/yr. With 27% of the Linganore Creek watershed in forest, over 10,300 may be eroded off of forested lands which is more than the average annual suspended-sediment load (8,050 Mg/yr) in Linganore Creek, indicating that much of the eroded forest sediment goes in storage. Most of the forested areas in the Chesapeake Bay watershed were cut down for agriculture between the time of European colonization and the early 20th Century. In the late 20th century forested lands show an increase in areal extent. Although studies have not been conducted to understand why these secondary growth forests are eroding, it may involve that these forests have not fully recovered from deforestation. Soil profiles are thin, and runoff and sediment relations may have been altered, leading to high rates of erosion.

Solid discharge and landslide activity at basin scale

NASA Astrophysics Data System (ADS)

Ardizzone, F.; Guzzetti, F.; Iadanza, C.; Rossi, M.; Spizzichino, D.; Trigila, A.

2012-04-01

This work presents a preliminary analysis aimed at understanding the relationship between landslide sediment supply and sediment yield at basin scale in central and southern Italy. A database of solid discharge measurements regarding 116 gauging stations, located along the Apennines chain in Italy, has been compiled by investigating the catalogues, named Annali Idrologici, published by Servizio Idrografico e Mareografico Italiano in the period from 1917 to 1997. The database records several information about the 116 gauging stations, and especially reports the sediment yield monthly measurements (103 ton) and the catchments area (km2). These data have been used to calculate the average solid yield and the normalized solid yield for each station in the observation period. The Italian Landslide Inventory (Progetto IFFI) has been used to obtained the size of the landslides, in order to estimate the landslide mobilization rates. The IFFI Project funded by the Italian Government is realized by ISPRA (Italian National Institute for Environmental Protection and Research - Geological Survey of Italy) in partnership with the 21 Regions and Self Governing Provinces. 21 of the 116 gauging stations and the related catchments have been selected on the basis of the length of the solid discharge observation period and excluding the catchments with dams located upstream the stations. The landslides inside the selected catchments have been extracted from the IFFI inventory, calculating the planimetric area of each landslide. Considering both the shallow and deep landslides, the landslide volume has been estimated using an empirical power law relation (landslide area vs. volume). The total landslide volume in the study areas and the average sediment yield measured at the gauging stations have been compared, analysing the behaviour of the basins which drainage towards the Tyrrhenian sea and the basins which drainage towards the Adriatic sea.

Estimating floodplain sedimentation in the Laguna de Santa Rosa, Sonoma County, CA

USGS Publications Warehouse

Curtis, Jennifer A.; Flint, Lorraine E.; Hupp, Cliff R.

2013-01-01

We present a conceptual and analytical framework for predicting the spatial distribution of floodplain sedimentation for the Laguna de Santa Rosa, Sonoma County, CA. We assess the role of the floodplain as a sink for fine-grained sediment and investigate concerns regarding the potential loss of flood storage capacity due to historic sedimentation. We characterized the spatial distribution of sedimentation during a post-flood survey and developed a spatially distributed sediment deposition potential map that highlights zones of floodplain sedimentation. The sediment deposition potential map, built using raster files that describe the spatial distribution of relevant hydrologic and landscape variables, was calibrated using 2 years of measured overbank sedimentation data and verified using longer-term rates determined using dendrochronology. The calibrated floodplain deposition potential relation was used to estimate an average annual floodplain sedimentation rate (3.6 mm/year) for the ~11 km2 floodplain. This study documents the development of a conceptual model of overbank sedimentation, describes a methodology to estimate the potential for various parts of a floodplain complex to accumulate sediment over time, and provides estimates of short and long-term overbank sedimentation rates that can be used for ecosystem management and prioritization of restoration activities.

A three-dimensional cohesive sediment transport model with data assimilation: Model development, sensitivity analysis and parameter estimation

NASA Astrophysics Data System (ADS)

Wang, Daosheng; Cao, Anzhou; Zhang, Jicai; Fan, Daidu; Liu, Yongzhi; Zhang, Yue

2018-06-01

Based on the theory of inverse problems, a three-dimensional sigma-coordinate cohesive sediment transport model with the adjoint data assimilation is developed. In this model, the physical processes of cohesive sediment transport, including deposition, erosion and advection-diffusion, are parameterized by corresponding model parameters. These parameters are usually poorly known and have traditionally been assigned empirically. By assimilating observations into the model, the model parameters can be estimated using the adjoint method; meanwhile, the data misfit between model results and observations can be decreased. The model developed in this work contains numerous parameters; therefore, it is necessary to investigate the parameter sensitivity of the model, which is assessed by calculating a relative sensitivity function and the gradient of the cost function with respect to each parameter. The results of parameter sensitivity analysis indicate that the model is sensitive to the initial conditions, inflow open boundary conditions, suspended sediment settling velocity and resuspension rate, while the model is insensitive to horizontal and vertical diffusivity coefficients. A detailed explanation of the pattern of sensitivity analysis is also given. In ideal twin experiments, constant parameters are estimated by assimilating 'pseudo' observations. The results show that the sensitive parameters are estimated more easily than the insensitive parameters. The conclusions of this work can provide guidance for the practical applications of this model to simulate sediment transport in the study area.

Decomposition of algal lipids in clay-enriched marine sediment under oxic and anoxic conditions

NASA Astrophysics Data System (ADS)

Lü, Dongwei; Song, Qian; Wang, Xuchen

2010-01-01

A series of laboratory incubation experiments were conducted to examine the decomposition of algal organic matter in clay-enriched marine sediment under oxic and anoxic conditions. During the 245-day incubation period, changes in the concentrations of TOC, major algal fatty acid components (14:0, 16:0, 16:1, 18:1 and 20:5), and n-alkanes (C16-C23) were quantified in the samples. Our results indicate that the organic matters were degraded more rapidly in oxic than anoxic conditions. Adsorption of fatty acids onto clay minerals was a rapid and reversible process. Using a simple G model, we calculated the decomposition rate constants for TOC, n-alkanes and fatty acids which ranged from 0.017-0.024 d-1, 0.049-0.103 d-1 and 0.011 to 0.069 d-1, respectively. Algal organic matter degraded in two stages characterized by a fast and a slow degradation processes. The addition of clay minerals montmorillonite and kaolinite to the sediments showed significant influence affecting the decomposition processes of algal TOC and fatty acids by adsorption and incorporation of the compounds with clay particles. Adsorption/association of fatty acids by clay minerals was rapid but appeared to be a slow reversible process. In addition to the sediment redox and clay influence, the structure of the compounds also played important roles in affecting their degradation dynamic in sediments.

The impact of suspended oyster farming on nitrogen cycling and nitrous oxide production in a sub-tropical Australian estuary

NASA Astrophysics Data System (ADS)

Erler, Dirk V.; Welsh, David T.; Bennet, William W.; Meziane, Tarik; Hubas, Cédric; Nizzoli, Daniele; Ferguson, Angus J. P.

2017-06-01

In this study we quantified nitrate (NO3-) reduction (denitrification, anammox and DNRA) and N2O production in sediments and epibiont communities associated with Sydney Rock Oyster (Saccostrea glomerata) farming. In sediments beneath an active suspended oyster farm, DNRA accounted for 98% of NO3- reduction with rates of up to 169 ± 45 μmol N m-2 h-1. Much of this DNRA was fuelled by NO3- derived from nitrification. Reference sediments had significantly lower DNRA rates of 83.8 ± 28.2 μmol N m-2 h-1, however this constituted 96% of the sites total NO3- reduction. Fatty acid analysis showed that sediment organic matter was more labile in the oyster impacted sediments, facilitating subtle shifts in sediment oxygen demand which increased the Fe2+ availability with respect to the reference sediments. The difference in DNRA rate between the sites was attributed to autotrophic oxidation of soluble Fe2+ in sediments underlying the oyster cultures. DNRA was absent in the oyster shell epibiont communities and rates of anammox and denitrification were lower than in the sediments. Production of NH4+ from the oysters and their associated epibionts was larger than DNRA and reached a rate of 206.2 μmol N m-2 h-1. Nitrous oxide production rates were generally low compared to other aquaculture systems and the net flux of N2O for the combined oyster cultivation system (i.e. sediments plus epibionts) was negative, i.e. there was N2O consumption in the sediments beneath the oysters. Overall, subtropical suspended oyster farming systems favour inorganic N retention over N loss.

Radionuclide transport in the "sediments - water - plants" system of the water bodies at the Semipalatinsk test site.

PubMed

Aidarkhanova, A K; Lukashenko, S N; Larionova, N V; Polevik, V V

2018-04-01

This paper provides research data on levels and character of radionuclide contamination distribution in the «sediments- water - plants » system of objects of the Semipalatinsk test site (STS). As the research objects there were chosen water bodies of man-made origin which located at the territory of "Experimental Field", "Balapan", "Telkem" and "Sary-Uzen" testing sites. For research the sampling of bottom sediments, water, lakeside and water plants was taken. Collected samples were used to determine concentration of anthropogenic radionuclides 90 Sr, 239+240 Pu, 241 Am, 137 Cs. The distribution coefficient (K d ) was calculated as the ratio of the content of radionuclides in the sediments to the content in water, and the concentration ratio (F V ) was calculated as the ratio of radionuclide content in plants to the content in sediments or soil. Copyright © 2018 Elsevier Ltd. All rights reserved.

Sediment transport induced by tidal bores. An estimation from suspended matter measurements in the Sée River (Mont-Saint-Michel Bay, northwestern France)

NASA Astrophysics Data System (ADS)

Furgerot, Lucille; Mouazé, Dominique; Tessier, Bernadette; Perez, Laurent; Haquin, Sylvain; Weill, Pierre; Crave, Alain

2016-07-01

Tidal bores are believed to induce significant sediment transport in macrotidal estuaries. However, due to high turbulence and very large suspended sediment concentration (SSC), the measurement of sediment transport induced by a tidal bore is actually a technical challenge. Consequently, very few quantitative data have been published so far. This paper presents SSC measurements performed in the Sée River estuary (Mont-Saint-Michel Bay, northwestern France) during the tidal bore passage with direct and indirect (optical) methods. Both methods are calibrated in laboratory in order to verify the consistency of measurements, to calculate the uncertainties, and to correct the raw data. The SSC measurements coupled with ADCP velocity data are used to calculate the instantaneous sediment transport (qs) associated with the tidal bore passage (up to 40 kg/m2/s).

Contribution of bank erosion to the sediment budget of a drained agricultural lowland catchment

NASA Astrophysics Data System (ADS)

Cerdan, Olivier; Foucher, Anthony; Vandromme, Rosalie; Salvador-Blanes, Sébastien; Gay, Aurore; Landemaine, Valentin; Evrard, Olivier

2017-04-01

Following the shift towards more intensive agriculture in cultivated lowlands in Europe, field sizes have increased and stream valley meanderings have been removed and realigned along new straight field borders. These modifications have led to profound alterations of the hydromorphology of the streams. To test the impact of these modifications, the long-term and current volumes of sediment originating from stream banks were calculated as they provided potential sources of sediment in a large pond located at the outlet of a small agricultural lowland basin under strong anthropogenic pressure. Bank erosion was measured using several methodologies, i) over a short period using a set of erosion pins along a small stream (1400 m long) to quantify the material exported during a single winter season (2012/2013); ii) over the last 69 years using an original approach involving the comparison of a compilation of three-dimensional historical stream redesign plans from 1944 vs. new measurements conducted in 2013 (DGPS and LiDAR data); iii) over several decades by using tracers (137Cs) that can differentiate between surface and subsoil erosion. At the catchment scale, total sediment exports were estimated from 1945 to 2013 combining seismic imagery and core dating in the lake. Sediment exports decreased with time, from 300 t. km-2.yr-between 1954 and 1980 to 95 t. km-2.yr-1 between 1980 and 2013. Today, erosion rates recorded at the outlet of the catchment vary between 90-102 t.km-2.yr-1. Therefore, the order of magnitude of the mean export rate is approximately 180 t. km-2.yr-1 for the last 70 years. The contribution of channel banks to this sediment export was the highest ( 30%) between 1954 and 1980 when the ditches were constructed. For the entire period since the landscape modification, the contribution of bank erosion is lower but still reaches 20%. Bank erosion can therefore be considered as a significant contributor to the sediment budget of the lowland catchments that have been redesigned after the 2nd world war in Western Europe.

A digital sedimentator for measuring erythrocyte sedimentation rate using a linear image sensor

NASA Astrophysics Data System (ADS)

Yoshikoshi, Akio; Sakanishi, Akio; Toyama, Yoshiharu

2004-11-01

A digital apparatus was fabricated to determine accurately the erythrocyte sedimentation rate (ESR) using a linear image sensor. Currently, ESR is utilized for clinical diagnosis, and in the laboratory as one of the many rheological properties of blood through the settling of red blood cells (RBCs). In this work, we aimed to measure ESR automatically using a small amount of a sample and without moving parts. The linear image sensor was placed behind a microhematocrit tube containing 36 μl of RBC suspension on a holder plate; the holder plate was fixed on an optical bench together with a tungsten lamp and an opal glass placed in front. RBC suspensions were prepared in autologous plasma with hematocrit H from 25% to 44%. The intensity profiles of transmitted light in 36 μl of RBC suspension were detected using the linear image sensor and sent to a personal computer every minute. ESR was observed at the settling interface between the plasma and RBC suspension in the profile in 1024 pixels (25 μm/pixel) along a microhematocrit tube of 25.6 mm total length for 1 h at a temperature of 37.0±0.1 °C. First, we determined the initial pixel position of the sample at the boundary with air. The boundary and the interface were defined by inflection points in the profile with 25 μm resolution. We obtained sedimentation curves that were determined by the RBC settling distance l(t) at the time t from the difference between pixel locations at the boundary and the interface. The sedimentation curves were well fitted to an empirical equation [Puccini et al., Biorheol. 14, 43 (1977)] from which we calculated the maximum sedimentation velocity smax at the time tmax. We reached tmax within 30 min at any H, and smax linearly related to the settling distance l(60) at 60 min after the start of sedimentation from 30% to 44% H with the correlation coefficient r=0.993. Thus, we may estimate conventional ESR at 1 h from smax more quickly and accurately with less effort.

Morphodynamic Modeling of the Lower Yellow River, China: Flux (Equilibrium) Form or Entrainment (Nonequilibrium) Form of Sediment Mass Conservation?

NASA Astrophysics Data System (ADS)

An, C.; Parker, G.; Ma, H.; Naito, K.; Moodie, A. J.; Fu, X.

2017-12-01

Models of river morphodynamics consist of three elements: (1) a treatment of flow hydraulics, (2) a formulation relating some aspect of sediment transport to flow hydraulics, and (3) a description of sediment conservation. In the case of unidirectional river flow, the Exner equation of sediment conservation is commonly described in terms of a flux-based formulation, in which bed elevation variation is related to the streamwise gradient of sediment transport rate. An alternate formulation of the Exner equation, however, is the entrainment-based formulation in which bed elevation variation is related to the difference between the entrainment rate of bed sediment into suspension and the deposition rate of suspended sediment onto the bed. In the flux-based formulation, sediment transport is regarded to be in a local equilibrium state (i.e., sediment transport rate locally equals sediment transport capacity). However, the entrainment-based formulation does not require this constraint; the sediment transport rate may lag in space and time behind the changing flow conditions. In modeling the fine-grained Lower Yellow River, it is usual to treat sediment conservation in terms of an entrainment-based (nonequilibrium) rather than a flux-based (equilibrium) formulation with the consideration that fine-grained sediment may be entrained at one place but deposited only at some distant location downstream. However, the differences in prediction between the two formulations are still not well known, and the entrainment formulation may not always be necessary for the Lower Yellow River. Here we study this problem by comparing the results of flux-based and entrainment-based morphodynamics under conditions typical of the Yellow River, using sediment transport equations specifically designed for the Lower Yellow River. We find, somewhat unexpectedly, that in a treatment of a 200-km reach using uniform sediment, there is little difference between the two formulations unless the sediment fall velocity is arbitrarily greatly reduced. A consideration of sediment mixtures, however, shows that the two formulations give very different patterns of grain sorting. We explain this in terms of the structures of the two Exner equations for sediment mixtures, and define conditions for applicability of each formulation.

Examples of Mass Wasting and Hemipelagic Sedimentation of Brazos-Trinity Basin #4 and Ursa Basin, Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Schneider, J.; Moerz, T.; Bartetzko, A.; Iturrino, G. J.; Edeskar, T. M.; Flemings, P. B.; Behrmann, J. H.; John, C. M.

2005-12-01

Pleistocene sea level changes influenced the sedimentation history on the passive continental margin of the northern Gulf of Mexico coast. During IODP Expedition 308, the Brazos-Trinity #4 and Ursa Basin were drilled to study -overpressure, fluid flow and deformation processes in a passive margin setting. The Brazos-Trinity Basin #4 is located 200 km south of Galveston, Texas (USA) in ~1400 m water depth below an extended shelf section. Ursa Basin is located 150 km south of New Orleans, Louisiana (USA) in ~1000 m water depth south of the Mississippi river mouth. Despite their similar geotectonic setting both basins show fundamental differences in their style of mass wasting and drape sedimentation. Here we use core descriptions, core photographs, Formation MicroScanner (FMS) data and selected physical properties measurements (magnetic susceptibility, GRAPE density) to illustrate and compare styles of mass wasting and drape sedimentation on selected intervals for the first 4 Marine Isotope Stages. Special emphasis is given to the thickness and frequency of single depositional events. One aim is to estimate the mass wasting / hemipelagic accumulation ratio for both basins and compare it to the average sedimentation rates based on the preliminary shipboard age models. This information will be used in the future to study how sedimentation processes control permeability and pore pressure. In this upcoming project, starting in mid 2006, will use well-logging data to compute continuous porosity, permeability, and pore pressure profiles. These computations require input and reference data obtained from petrophysical and geotechnical core analyses and in situ measurements (e.g. matrix density to calculate porosity from the density log, permeability and porosity to derive porosity-permeability relations, effective stress to calculate pore pressure). Permeability and effective stress will be measured using oedometer tests on undisturbed samples. The detailed lithostratigraphic information, particularly turbidite thickness, and the permeability and pore pressure profiles will be used as input data for one-dimensional modeling of the compression history of two Sites using the civil engineering modeling software PLAXIS.

Sediment dynamics over multiple time scales in Dyke Marsh Preserve (Potomac River, VA)

NASA Astrophysics Data System (ADS)

Palinkas, C. M.; Walters, D.

2010-12-01

Tidal freshwater marshes are critical components of fluvial and estuarine ecosystems, yet sediment dynamics within them have not received as much attention as their saltwater counterparts. This study examines sedimentation in Dyke Marsh Preserve, located on the Potomac River (VA), focusing on understanding the spatial variability present over multiple time scales. Bimonthly sediment data were collected using ceramic tiles, and seasonal- and decadal-scale sedimentation was determined via 7Be (half-life 53.3 days) and 210Pb (half-life 22.3 years), respectively. Results were also compared to SET data collected by the National Park Service since 2006. Preliminary data indicate that sites at lower elevations have higher sedimentation rates, likely related to their close proximity to the sediment source. Mass accumulation rates generally decreased with increasing time scale, such that the seasonal rates were greater than the SET-derived accretion rates, which were in turn greater than the decadal-scale rates. However, the bimonthly rates were the lowest observed, probably because the sampling period (May-October 2010) did not include the main depositional period of the year, which would be integrated by the other techniques.

ESR

MedlinePlus

Erythrocyte sedimentation rate; Sed rate; Sedimentation rate ... Reasons why a "sed rate" may be done include: Unexplained fevers Certain types of arthritis Muscle symptoms Other vague symptoms that cannot be explained This ...

Planktic foraminiferal assemblages from laminated sediments of the northeastern Arabian Sea: a high-resolution study over the last two millennia

NASA Astrophysics Data System (ADS)

Munz, Philipp; Lückge, Andreas; Siccha, Michael; Kucera, Michal; Schulz, Hartmut

2014-05-01

Modern planktic foraminiferal assemblages in the Arabian Sea are largely controlled by seasonal shifts of surface water properties. Boreal summer (June-September) heating of the Asian landmass and Tibetan Plateau leads to northward migration of the ITCZ and develops an intense atmospheric pressure gradient. Strong monsoonal winds from the southwest lead to coastal- and open ocean upwelling, especially in the western Arabian Sea along the coast of Somalia and Oman. Opposite directed dry and cold winds lead to deep convective mixing during boreal winter (January-March) and breakup of the thermal stratification. Deepening of the mixed-layer thus enables nutrient transport into the photic zone with enhanced primary production. Here we study planktic foraminiferal assemblages from the dominantly winter monsoon controlled Pakistan Margin off Karachi. We sampled annually laminated sediments from box core SO90-39KG and ca. 2-m-long piston core SO130-275KL from the same station. High sedimentation rates and varve-like lamination provides a particular record with very precise age control. Box core 39KG offers a record of the last 100 years with 2-year-resolution and 275KL provides a ca. 10-year-resolution during the last 2100 years. We calculated foraminiferal flux rates after photometric identification and subtraction of light-colored event layers, consisting solely of terrigeneous matter to enable comparison with flux rates from sediment trap stations. We identified a total of 28 planktic foraminiferal (PF) species/morphotypes in the fraction >150μm. During the relatively short period of the past two millennia, several species showed comparatively large fluctuations on decadal time scales, not seen in bioturbated records. Globigerina bulloides, a species generally associated with high primary production rates, fluctuates between ca. 10% and 45%. Highest relative share was observed during periods 1593-1413, 1023-923, 483-393, 63- -7 years AD. Average PF accumulation rates follow a general decreasing trend from ca. 30,000 individuals cm-2 kyr-1 at 100 years BC to 9,000 ind. cm-2 kyr-1 at 1890 years AD, suggesting a decrease in absolute PF production.

The role of burrowing sponges in bioerosion.

PubMed

Rützler, Klaus

1975-09-01

Among the large number of limestone-eroding organisms, sponges, mainly of the family Clinonidae are of special interest because of their efficient means of substratum penetration by cellular etching and because they release characteristically shaped calcium carbonate chips which can be detected in the mud-size fraction of many sediments. Identifiable trace fossils and sediments are of great ecological and paleoecological significance.As new data on the excavating mechanism have become available, the questions of burrowing rates and sediment production have gained importance. Extrapolation from shortterm experiments (under 6 months) on substrate invasion are inconclusive because of high initial penetration rates resulting from mechanical stimulation and lack of competition. New experiments show that the rate curve flattens after 6 months and that optimum longterm erosion of CaCO 3 does not exceed 700 mg m -2 year -1 (Cliona lampa and C. aprica). Substrate limitations and competition will further reduce this rate.By monitoring the production of CaCO 3 chips by Cliona lampa, it was possible to link activity patterns to certain environmental factors. Mechanical stimuli, high light intensity, strong currents and, possibly, low temperature seem to accelerate the burrowing process. Sponge-generated chips can make up over 40% of coral mud when deposited in the current shadow of the reef framework.Using transect counts and sponge area-biomass conversion factors, the mean abundance of burrowing sponges on the Bermuda platform could be calculated. On suitable hard bottom substrates it averages 16 g dry weight per m 2 . From this value the burrowing potential of sponges can be estimated as 256 g CaCO 3 per m 2 substrate per year. Since 97-98% of the eroded limestone remains in particulate form, the contribution of fine sediments can amount to 250 g m -2 year -1 .Attention is called to the fact that erosion rates by burrowers can not directly be compared with those of borers or scrapers. The former are intermittent and their activities are affected by environmental and biological interactions, while activities of the latter are rather constant and guided by the need for food.

Delta lobe degradation and hurricane impacts governing large-scale coastal behavior, South-central Louisiana, USA

USGS Publications Warehouse

Miner, M.D.; Kulp, M.A.; FitzGerald, D.M.; Flocks, J.G.; Weathers, H.D.

2009-01-01

A large deficit in the coastal sediment budget, high rates of relative sea-level rise (???0.9 cm/year), and storm-induced current and wave erosion are forcing barrier shoreface retreat along the periphery of the Mississippi River delta plain. Additionally, conversion of interior wetlands to open water has increased the bay tidal prism, resulting in degradation of barrier islands due to inlet widening, formation of new inlets, and sediment sequestration at ebb-tidal deltas. Single-beam bathymetric surveys along a 165-km stretch of south-central Louisiana barrier coast, from Raccoon Point in Terrebonne Parish to Sandy Point in Plaquemines Parish, were conducted in 2006. These data, combined with historical bathymetry from three time periods (dating to the 1880s), provide a series of digital elevation models that were used to calculate sediment volumetric changes and determine long-term erosional-depositional trends. Dominant patterns during the 125-year period include (1) erosion of ???1.6????????109 m3 from the shoreface, forcing up to 3 km of shoreface retreat, (2) sediment deposition in coastal bights and at ebb-tidal deltas, and (3) a combined increase in tidal inlet cross-sectional area from ???41,400 m2 to ???139,500 m 2. Bathymetric and shoreline change datasets separated by shorter time periods (sub-annual) demonstrate that these long-term trends are driven by processes associated with major hurricane impacts, and that rates of shoreface erosion are an order of magnitude greater during active hurricane seasons compared to long-term trends. ?? 2009 Springer-Verlag.

Spatial Distribution of Bed Particles in Natural Boulder-Bed Streams

NASA Astrophysics Data System (ADS)

Clancy, K. F.; Prestegaard, K. L.

2001-12-01

The Wolman pebble count is used to obtain the size distribution of bed particles in natural streams. Statistics such as median particle size (D50) are used in resistance calculations. Additional information such as bed particle heterogeneity may also be obtained from the particle distribution, which is used to predict sediment transport rates (Hey, 1979), (Ferguson, Prestegaard, Ashworth, 1989). Boulder-bed streams have an extreme range of particles in the particle size distribution ranging from sand size particles to particles larger than 0.5-m. A study of a natural boulder-bed reach demonstrated that the spatial distribution of the particles is a significant factor in predicting sediment transport and stream bed and bank stability. Further experiments were performed to test the limits of the spatial distribution's effect on sediment transport. Three stream reaches 40-m in length were selected with similar hydrologic characteristics and spatial distributions but varying average size particles. We used a grid 0.5 by 0.5-m and measured four particles within each grid cell. Digital photographs of the streambed were taken in each grid cell. The photographs were examined using image analysis software to obtain particle size and position of the largest particles (D84) within the reach's particle distribution. Cross section, topography and stream depth were surveyed. Velocity and velocity profiles were measured and recorded. With these data and additional surveys of bankfull floods, we tested the significance of the spatial distributions as average particle size decreases. The spatial distribution of streambed particles may provide information about stream valley formation, bank stability, sediment transport, and the growth rate of riparian vegetation.

Sedimentation rates and patterns in beaver ponds in a mountain environment

NASA Astrophysics Data System (ADS)

Butler, David R.; Malanson, George P.

1995-09-01

Sediment depth was measured at several sites within each of eight beaver ponds in Glacier National Park, Montana, and sediment samples wen; collected from five of these ponds. Accumulation rates of sediments far exceeded published rates from boreal forest landscapes in eastem and central North America. Pond area strongly predicts volume of sedimentation. Textural differences illustrated spatial variations associated with position in a pond and along a pond sequence. Organic matter content was significantly higher in older ponds, and has ramifications for the development of the benthos and the long-term storage of matter in ponds. The role of beavers as biogeomorphic agents is profound, but requires further elucidation to distinguish between fluvial sediment deposition in ponds and sediment deposition associated with beaver excavational activity.

A mass balance approach to investigate arsenic cycling in a petroleum plume.

PubMed

Ziegler, Brady A; Schreiber, Madeline E; Cozzarelli, Isabelle M; Crystal Ng, G-H

2017-12-01

Natural attenuation of organic contaminants in groundwater can give rise to a series of complex biogeochemical reactions that release secondary contaminants to groundwater. In a crude oil contaminated aquifer, biodegradation of petroleum hydrocarbons is coupled with the reduction of ferric iron (Fe(III)) hydroxides in aquifer sediments. As a result, naturally occurring arsenic (As) adsorbed to Fe(III) hydroxides in the aquifer sediment is mobilized from sediment into groundwater. However, Fe(III) in sediment of other zones of the aquifer has the capacity to attenuate dissolved As via resorption. In order to better evaluate how long-term biodegradation coupled with Fe-reduction and As mobilization can redistribute As mass in contaminated aquifer, we quantified mass partitioning of Fe and As in the aquifer based on field observation data. Results show that Fe and As are spatially correlated in both groundwater and aquifer sediments. Mass partitioning calculations demonstrate that 99.9% of Fe and 99.5% of As are associated with aquifer sediment. The sediments act as both sources and sinks for As, depending on the redox conditions in the aquifer. Calculations reveal that at least 78% of the original As in sediment near the oil has been mobilized into groundwater over the 35-year lifespan of the plume. However, the calculations also show that only a small percentage of As (∼0.5%) remains in groundwater, due to resorption onto sediment. At the leading edge of the plume, where groundwater is suboxic, sediments sequester Fe and As, causing As to accumulate to concentrations 5.6 times greater than background concentrations. Current As sinks can serve as future sources of As as the plume evolves over time. The mass balance approach used in this study can be applied to As cycling in other aquifers where groundwater As results from biodegradation of an organic carbon point source coupled with Fe reduction. Copyright © 2017 Elsevier Ltd. All rights reserved.

A mass balance approach to investigate arsenic cycling in a petroleum plume

USGS Publications Warehouse

Ziegler, Brady A.; Schreiber, Madeline E.; Cozzarelli, Isabelle M.; Ng. G.-H. Crystal,

2017-01-01

Natural attenuation of organic contaminants in groundwater can give rise to a series of complex biogeochemical reactions that release secondary contaminants to groundwater. In a crude oil contaminated aquifer, biodegradation of petroleum hydrocarbons is coupled with the reduction of ferric iron (Fe(III)) hydroxides in aquifer sediments. As a result, naturally occurring arsenic (As) adsorbed to Fe(III) hydroxides in the aquifer sediment is mobilized from sediment into groundwater. However, Fe(III) in sediment of other zones of the aquifer has the capacity to attenuate dissolved As via resorption. In order to better evaluate how long-term biodegradation coupled with Fe-reduction and As mobilization can redistribute As mass in contaminated aquifer, we quantified mass partitioning of Fe and As in the aquifer based on field observation data. Results show that Fe and As are spatially correlated in both groundwater and aquifer sediments. Mass partitioning calculations demonstrate that 99.9% of Fe and 99.5% of As are associated with aquifer sediment. The sediments act as both sources and sinks for As, depending on the redox conditions in the aquifer. Calculations reveal that at least 78% of the original As in sediment near the oil has been mobilized into groundwater over the 35-year lifespan of the plume. However, the calculations also show that only a small percentage of As (∼0.5%) remains in groundwater, due to resorption onto sediment. At the leading edge of the plume, where groundwater is suboxic, sediments sequester Fe and As, causing As to accumulate to concentrations 5.6 times greater than background concentrations. Current As sinks can serve as future sources of As as the plume evolves over time. The mass balance approach used in this study can be applied to As cycling in other aquifers where groundwater As results from biodegradation of an organic carbon point source coupled with Fe reduction.

Quantifying periglacial erosion: Insights on a glacial sediment budget, Matanuska Glacier, Alaska

USGS Publications Warehouse

O'Farrell, C. R.; Heimsath, A.M.; Lawson, D.E.; Jorgensen, L.M.; Evenson, E.B.; Larson, G.; Denner, J.

2009-01-01

Glacial erosion rates are estimated to be among the highest in the world. Few studies have attempted, however, to quantify the flux of sediment from the periglacial landscape to a glacier. Here, erosion rates from the nonglacial landscape above the Matanuska Glacier, Alaska are presented and compare with an 8-yr record of proglacial suspended sediment yield. Non-glacial lowering rates range from 1??8 ?? 0??5 mm yr-1 to 8??5 ?? 3??4 mm yr-1 from estimates of rock fall and debris-flow fan volumes. An average erosion rate of 0??08 ?? 0??04 mm yr-1 from eight convex-up ridge crests was determined using in situ produced cosmogenic 10Be. Extrapolating these rates, based on landscape morphometry, to the Matanuska basin (58% ice-cover), it was found that nonglacial processes account for an annual sediment flux of 2??3 ?? 1??0 ?? 106 t. Suspended sediment data for 8 years and an assumed bedload to estimate the annual sediment yield at the Matanuska terminus to be 2??9 ?? 1??0 ?? 106 t, corresponding to an erosion rate of 1??8 ?? 0??6 mm yr-1: nonglacial sources therefore account for 80 ?? 45% of the proglacial yield. A similar set of analyses were used for a small tributary sub-basin (32% ice-cover) to determine an erosion rate of 12??1 ?? 6??9 mm yr-1, based on proglacial sediment yield, with the nonglacial sediment flux equal to 10 ?? 7% of the proglacial yield. It is suggested that erosion rates by nonglacial processes are similar to inferred subglacial rates, such that the ice-free regions of a glaciated landscape contribute significantly to the glacial sediment budget. The similar magnitude of nonglacial and glacial rates implies that partially glaciated landscapes will respond rapidly to changes in climate and base level through a rapid nonglacial response to glacially driven incision. ?? 2009 John Wiley & Sons, Ltd.

Geochemical modeling of iron, sulfur, oxygen and carbon in a coastal plain aquifer

NASA Astrophysics Data System (ADS)

Brown, C. J.; Schoonen, M. A. A.; Candela, J. L.

2000-11-01

Fe(III) reduction in the Magothy aquifer of Long Island, NY, results in high dissolved-iron concentrations that degrade water quality. Geochemical modeling was used to constrain iron-related geochemical processes and redox zonation along a flow path. The observed increase in dissolved inorganic carbon is consistent with the oxidation of sedimentary organic matter coupled to the reduction of O 2 and SO 42- in the aerobic zone, and to the reduction of SO 42- in the anaerobic zone; estimated rates of CO 2 production through reduction of Fe(III) were relatively minor by comparison. The rates of CO 2 production calculated from dissolved inorganic carbon mass transfer (2.55×10 -4 to 48.6×10 -4 mmol l -1 yr-1) generally were comparable to the calculated rates of CO 2 production by the combined reduction of O 2, Fe(III) and SO 42- (1.31×10 -4 to 15×10 -4 mmol l -1 yr-1). The overall increase in SO 42- concentrations along the flow path, together with the results of mass-balance calculations, and variations in δ34S values along the flow path indicate that SO 42- loss through microbial reduction is exceeded by SO 42- gain through diffusion from sediments and through the oxidation of FeS 2. Geochemical and microbial data on cores indicate that Fe(III) oxyhydroxide coatings on sediment grains in local, organic carbon- and SO 42--rich zones have been depleted by microbial reduction and resulted in localized SO 42--reducing zones in which the formation of iron disulfides decreases dissolved iron concentrations. These localized zones of SO 42- reduction, which are important for assessing zones of low dissolved iron for water-supply development, could be overlooked by aquifer studies that rely only on groundwater data from well-water samples for geochemical modeling.

Complexities in barrier island response to sea level rise: Insights from numerical model experiments, North Carolina Outer Banks

USGS Publications Warehouse

Moore, Laura J.; List, Jeffrey H.; Williams, S. Jeffress; Stolper, David

2010-01-01

Using a morphological-behavior model to conduct sensitivity experiments, we investigate the sea level rise response of a complex coastal environment to changes in a variety of factors. Experiments reveal that substrate composition, followed in rank order by substrate slope, sea level rise rate, and sediment supply rate, are the most important factors in determining barrier island response to sea level rise. We find that geomorphic threshold crossing, defined as a change in state (e.g., from landward migrating to drowning) that is irreversible over decadal to millennial time scales, is most likely to occur in muddy coastal systems where the combination of substrate composition, depth-dependent limitations on shoreface response rates, and substrate erodibility may prevent sand from being liberated rapidly enough, or in sufficient quantity, to maintain a subaerial barrier. Analyses indicate that factors affecting sediment availability such as low substrate sand proportions and high sediment loss rates cause a barrier to migrate landward along a trajectory having a lower slope than average barrier island slope, thereby defining an “effective” barrier island slope. Other factors being equal, such barriers will tend to be smaller and associated with a more deeply incised shoreface, thereby requiring less migration per sea level rise increment to liberate sufficient sand to maintain subaerial exposure than larger, less incised barriers. As a result, the evolution of larger/less incised barriers is more likely to be limited by shoreface erosion rates or substrate erodibility making them more prone to disintegration related to increasing sea level rise rates than smaller/more incised barriers. Thus, the small/deeply incised North Carolina barriers are likely to persist in the near term (although their long-term fate is less certain because of the low substrate slopes that will soon be encountered). In aggregate, results point to the importance of system history (e.g., previous slopes, sediment budgets, etc.) in determining migration trajectories and therefore how a barrier island will respond to sea level rise. Although simple analytical calculations may predict barrier response in simplified coastal environments (e.g., constant slope, constant sea level rise rate, etc.), our model experiments demonstrate that morphological-behavior modeling is necessary to provide critical insights regarding changes that may occur in environments having complex geometries, especially when multiple parameters change simultaneously.

Shoreline Erosion in the Albemarle-Pamlico Estuarine System, Northeastern North Carolina

NASA Astrophysics Data System (ADS)

Murphy, M. A.; Riggs, S. R.

2002-12-01

Computer analysis of aerial photographic series demonstrates that the estuarine shorelines within the North Carolina Albemarle-Pamlico coastal system are eroding at 2-3 times greater rates than previous studies reported. Specific rates and amounts of shoreline recession vary tremendously depending upon local variables including: 1) shoreline type, geometry, and composition; 2) geographic location, size, and shape of associated estuary; 3) frequency, intensity, and fetch of storms; 4) type and abundance of associated vegetation; and locally 5) boat wakes. Organic or wetland shorelines (marsh and swamp forest) comprise approximately 62% of the estuarine margins in NE NC, whereas sediment banks (low, high, and bluff) constitute about 38%. The goals of this study were to determine the rates of recession for different shoreline types and the role of local variables in the erosion process. Shorelines were mapped using high precision GPS mapping techniques, digital orthographic quarter quadrangles, and other georeferenced aerial photographs from the early 1950's to 2001. Shoreline change was then calculated for 20 estuarine study sites. Field mapping of each site provided data on shoreline characteristics and erosional processes. Data synthesis suggests mean annual shoreline erosion rates are significantly different for shoreline types as follows: 1) marshes = 7.4 ft/yr (range 2.7-17.0 ft/yr), low sediment banks = 5.0 ft/yr (range 1.0-12.0 ft/yr), bluff sediment banks = 5.0 ft/yr (range = 3.9-6.0 ft/yr), swamp forests = 3.0 ft/yr (range = 1.7-4.0 ft/yr), high sediment banks = 2.8 ft/yr (range = 2.7-2.9 ft/yr). Modified shorelines continue to erode, however at lower mean annual rates that range from 0.9-2.7 ft/yr. Locally, specific marsh shorelines have eroded at rates up to 100 ft/yr during particularly stormy periods. Thus, about 1166 acres of land are lost each year along the 1593 miles of mapped estuarine shoreline in NE NC. If these erosion rates are representative of all 3,000 miles of NE NC's estuarine shorelines, if sea level continues to rise, and if the storm pattern persists at present levels, NC will experience significant loss of both wetlands and uplands at the estuarine water-land interface.

Sediment inflow, outflow and deposition for Lakes Marion and Moultrie, South Carolina, October 1983-March 1985

USGS Publications Warehouse

Cooney, T.W.

1988-01-01

In 1941 a Coastal Plain reach of the Santee River was impounded to form Lake Marion and diverted into a diked-off part of the Cooper River basin to form Lake Moultrie. Rates of sediment inflow and outflow of the lakes were determined by the U.S. Geological Survey for the periods July 1966 - June 1968 and October 1983 - March 1985. Total sediment discharge was estimated for two inflow stations and continuous streamflow monitors and automatic suspended-sediment samplers were used for computation of suspended-sediment discharge. Bedload discharge was computed by the modified Einstein procedure. Suspended-sediment discharge was monitored at three outflow stations, with the suspended-sediment concentration measured on a weekly basis. During the 1983-1985 study, mean annual suspended-sediment inflow to Lakes Marion and Moultrie was estimated to be 722,000 tons, and the outflow was estimated at 175,000 tons, for a trap efficiency of 76% and a deposition rate of about 547,000 tons/year. This is about 33% less than the deposition rate determined during the 1966-68 study. The deposition rate for suspended and bedload sediment during the 1983 - 1985 study was about 650,000 tons/year. (USGS)

Comparison of Erosion Rates Estimated by Sediment Budget Techniques and Suspended Sediment Monitoring and Regulatory Implications

NASA Astrophysics Data System (ADS)

O'Connor, M.; Eads, R.

2007-12-01

Watersheds in the northern California Coast Range have been designated as "impaired" with respect to water quality because of excessive sediment loads and/or high water temperature. Sediment budget techniques have typically been used by regulatory authorities to estimate current erosion rates and to develop targets for future desired erosion rates. This study examines erosion rates estimated by various methods for portions of the Gualala River watershed, designated as having water quality impaired by sediment under provisions of the Clean Water Act Section 303(d), located in northwest Sonoma County (~90 miles north of San Francisco). The watershed is underlain by Jurassic age sedimentary and meta-sedimentary rocks of the Franciscan formation. The San Andreas Fault passes through the western edge of watershed, and other active faults are present. A substantial portion of the watershed is mantled by rock slides and earth flows, many of which are considered dormant. The Coast Range is geologically young, and rapid rates of uplift are believed to have contributed to high erosion rates. This study compares quantitative erosion rate estimates developed at different spatial and temporal scales. It is motivated by a proposed vineyard development project in the watershed, and the need to document conditions in the project area, assess project environmental impacts and meet regulatory requirements pertaining to water quality. Erosion rate estimates were previously developed using sediment budget techniques for relatively large drainage areas (~100 to 1,000 km2) by the North Coast Regional Water Quality Control Board and US EPA and by the California Geological Survey. In this study, similar sediment budget techniques were used for smaller watersheds (~3 to 8 km2), and were supplemented by a suspended sediment monitoring program utilizing Turbidity Threshold Sampling techniques (as described in a companion study in this session). The duration of the monitoring program to date spanned the winter runoff seasons of Water Years 2006 and 2007. These were unusually wet and dry years, respectively, providing perspective on the range of measured sediment yield in relation to sediment budget estimates. The measured suspended sediment yields were substantially lower than predicted by sediment budget methods. Variation in geomorphic processes over time and space and methodological problems of sediment budgets may be responsible for these apparent discrepancies. The implications for water quality policy are discussed.

Sediment production from forest road surfaces.

Treesearch

Leslie Reid; T. Dunne

2011-01-01

Erosion on roads is an important source of fine-grained sediment in streams draining logged basins of the Pacific Northwest. Runoff rates and sediment concentrations from 10 road segments subject to a variety of traffic levels were monitored to produce sediment rating curves and unit hydrographs for different use levels and types of surfaces. These relationships are...

Post-fire bedload sediment delivery across spatial scales in the interior western United States

Treesearch

Joseph W. Wagenbrenner; Peter R. Robichaud

2014-01-01

Post-fire sediment yields can be up to three orders of magnitude greater than sediment yields in unburned forests. Much of the research on post-fire erosion rates has been at small scales (100m2 or less), and post-fire sediment delivery rates across spatial scales have not been quantified in detail. We developed relationships for post-fire bedload sediment delivery...

Active overbank deposition during the last century, South River, Virginia

NASA Astrophysics Data System (ADS)

Pizzuto, Jim; Skalak, Katherine; Pearson, Adam; Benthem, Adam

2016-03-01

We quantify rates of overbank deposition over decadal to centennial timescales along the South River in Virginia using four independent methods. Detailed mercury profiles sampled adjacent to the stream channel preserve the peak historic mercury concentration on suspended sediment dating from 1955 to 1961 and suggest sedimentation rates of 8 to 50 cm/100 years. Sediment accumulation over the roots of trees suggest rates of 0 to 100 cm/100 years, with significantly higher values on levees and lower values on floodplains farther from the channel. Profiles of 137Cs and 210Pb from two eroding streambanks are fit with an advection-diffusion model calibrated at an upland reference site; these methods suggest sedimentation rates of 44 to 73 cm/100 years. Mercury inventories from 107 floodplain cores, combined with a previously published reconstruction of the history of mercury concentration on suspended sediment, provide spatially comprehensive estimates of floodplain sedimentation: median sedimentation rates are 3.8 cm/100 years for the < 0.3-year floodplain, 1.37 cm/100 years for the 0.3- to 2-year floodplain, 0.4 cm/100 years for the 2- to 5-year floodplain, and 0.1 cm/100 years for the 5- to 62-year floodplain. While these sedimentation rates are relatively low, the total mass of sediment stored from 1930 to 2007 is 4.9 ± 1.7 (95% confidence interval) × 107 kg, corresponding to an average thickness of 2.5 cm (3.2 cm/100 years). These results demonstrate that floodplains of our 4.5-km-long study reach have stored 8 to 12% of the total suspended sediment supplied to the study reach of the South River. Hydrologic Engineering Center-River Analysis System (HEC-RAS) modeling demonstrates that the floodplain of the South River remains hydraulically connected to the channel: 56% of the 100-year floodplain is inundated every two years, and 83% of the floodplain is inundated every five years. These results, combined with previously published data, provide the basis for a regional synthesis of floodplain deposition rates since European settlement. Floodplain sedimentation rates were high following European settlement, with published estimates ranging from 50 to 200 cm/100 years. Sedimentation rates decreased by 1 to 2 orders of magnitude during the twentieth and twenty-first centuries; but despite these lower sedimentation rates, floodplains continue to store a significant fraction of total suspended sediment load. Many floodplains of the mid-Atlantic region are active landforms fully connected to the rivers that flow within them and should not be considered terraces isolated from contemporary fluvial processes by post-settlement aggradation.

The Effectiveness of Hybrid Structure in Overcoming Coastal Abration in Trimulyo, Genuk Subdistrict Semarang City

NASA Astrophysics Data System (ADS)

Kurnia, Domas; Nugroho, Denny

2018-02-01

Trimulyo is one of coastal village in Genuk Subdistrict, Semarang City which now facing serious coastal abrasion. Such a thing has been causing loss of ponds and settlements. One of solution which currently carried is hybrid structure which combining permeable structure to break up the waves and trap sediment. The hybrid structure is designed as agitation dredging, which increase suspended sediment in sea water. The goals of this research were to studying the effectiveness of hybrid structure in handling coastal abration and to counting the volume of sedimentation during 20 months as well as rate of sedimentation. To reach the goals, high resolution satellite imagery year 2015 and 2016, scaled stick and sediment trap were applied to the study. Image processing was conducted by using Arc GIS 10.3 software. The effectiveness of hybrid structured was determined by series of field survey of existing condition. Rate of sedimentation measured during before and after hybrid structure built (20 months). The results showed that hybrid structure was effective to reduce coastal abrasion, it proven by a large amount of sediment was trapped behind the structure and coastline was upward along 170 meter since it was built. The volume of sediment during 20 months is 81.500 m3. If it assumed that the rate of sedimentation constantly, monthly rate of sedimentation is 4.075 m3/month or daily rate is 135,8 m3/day. The sediment that has formed highly recommended to use as mangrove conservation area in Semarang City.

Advection within shallow pore waters of a coastal lagoon, Florida

USGS Publications Warehouse

Cable, J.E.; Martin, Jonathan B.; Swarzenski, Peter W.; Lindenberg, Mary K.; Steward, Joel

2004-01-01

Ground water sources can be a significant portion of a local water budget in estuarine environments, particularly in areas with high recharge rates, transmissive aquifers, and permeable marine sediments. However, field measurements of ground water discharge are often incongruent with ground water flow modeling results, leaving many scientists unsure which estimates are accurate. In this study, we find that both measurements and model results are reasonable. The difference between estimates apparently results from the sources of water being measured and not the techniques themselves. In two locations in the Indian River Lagoon estuarine system, we found seepage meter rates similar to rates calculated from the geochemical tracers 222Rn and 226Ra. Ground water discharge rates ranged from 4 to 9 cm/d using seepage meters and 3 to 20 cm/d using 222Rn and 226Ra. In contrast, in comparisons to other studies where finite element ground water flow modeling was used, much lower ground water discharge rates of ∼0.05 to 0.15 cm/d were estimated. These low rates probably represent discharge of meteoric ground water from land-recharged aquifers, while the much higher rates measured with seepage meters, 222Rn, and 226Ra likely include an additional source of surface waters that regularly flush shallow (< 1 m depth) sediments. This resultant total flow of mixed land-recharged water and recirculated surface waters contributes to the total biogeochemical loading in this shallow estuarine environment.

In situ redox manipulation of subsurface sediments from Fort Lewis, Washington: Iron reduction and TCE dechlorination mechanisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

JE Szecsody; JS Fruchter; DS Sklarew

2000-03-21

Pacific Northwest National Laboratory (PNNL) conducted a bench-scale study to determine how effective chemically treated Ft. Lewis sediments can degrade trichloroethylene (TCE). The objectives of this experimental study were to quantify: (1) sediment reduction and oxidation reactions, (2) TCE degradation reactions, and (3) other significant geochemical changes that occurred. Sediment reduction and oxidation were investigated to determine the mass of reducible iron in the Ft. Lewis sediments and the rate of this reduction and subsequent oxidation at different temperatures. The temperature dependence was needed to be able to predict field-scale reduction in the relatively cold ({approximately}11 C) Ft. Lewis aquifer.more » Results of these experiments were used in conjunction with other geochemical and hydraulic characterization to design the field-scale injection experiment and predict barrier longevity. For example, the sediment reduction rate controls the amount of time required for the dithionite solution to fully react with sediments. Sediment oxidation experiments were additionally conducted to determine the oxidation rate and provide a separate measure of the mass of reduced iron. Laboratory experiments that were used to meet these objectives included: (1) sediment reduction in batch (static) systems, (2) sediment reduction in 1-D columns, and (3) sediment oxidation in 1-D columns. Multiple reaction modeling was conducted to quantify the reactant masses and reaction rates.« less

Evaluating the Role of Small Impoundments in Legacy Sediment Storage

NASA Astrophysics Data System (ADS)

Bain, D. J.; Salant, N.; Green, M. B.; Wreschnig, A. J.; Urbanova, T.

2009-12-01

Recent research highlighting the prevalence of dams built for water power in the mid-1800s has led to suggestions that strategies for managing legacy sediment in the Eastern United States should be re-evaluated. However, the link between reach-scale observations of historic dam sites to processes at the catchment scale have not been examined, nor have the role of other, similar historic changes been evaluated. This presentation will compare dam dynamics, including mill density data and synthetic estimates of beaver populations with sedimentation rates recorded in sediment cores. If low-head dams were a dominant mechanism in sediment storage, we expect to see changes in sedimentation rates with the expatriation of the beaver and the rise and decline of water power. Further, we expect to see spatial variation in these changes as beaver and mill densities and potential sediment yield are spatially heterogeneous. Ultimately, dramatic changes in sediment yield due to land use and hydrological alterations likely drove sedimentation rates; the mechanistic importance of storage likely depends on temporal coincidence.

River mouth morphodynamics - Examples from small, mountainous rivers (Invited)

NASA Astrophysics Data System (ADS)

Warrick, J. A.

2013-12-01

Small, high-sediment yield rivers are known to discharge massive amounts of sediment to the world's oceans. Because of these high rates of sediment discharge, many of these small rivers provide important sources of sediment to littoral cells, such as those along the west coasts of North and South America. Sediment discharge from these small watersheds is commonly ephemeral and dominated by infrequent high flow. Thus, the morphodynamic states of these river mouths will vary with time, often being 'wave dominated' for the majority of the year and then changing to 'river dominated' during river sediment discharge events. Here I will provide a summary of recent observations of the morphodynamics of river mouths along California that reveal that sediment dispersal and deposition patterns vary owing to the sediment transport processes at the river mouths, which are influenced by the buoyancy of the river discharge. During low rates of sediment discharge and low river sediment concentrations, sediment dispersal will occur in hypopycnal (positively buoyant) plumes and sand deposition will be close to the river mouth. These conditions commonly result in transfer of sand from the river delta to the littoral cell during the first 1-2 years following the river discharge event. During high rates of sediment discharge and high river sediment concentrations, river discharge may form hyperpycnal (negatively buoyant) plumes and disperse sand to deeper portions of the continental shelf, where transfer back to the littoral cell may take decades or may not occur. High-resolution bathymetry from southern California provides several examples of sand dispersal by hyperpycnal plumes to regions of the inner and middle continental shelf. Thus, sediment dispersal from river mouths influences coastal morphodynamics, morphology, and the rates and timing of sediment supply to littoral cells.

Gold in the hills: patterns of placer gold accumulation under dynamic tectonic and climatic conditions

NASA Astrophysics Data System (ADS)

Roy, Sam; Upton, Phaedra; Craw, Dave

2018-01-01

Formation of placer accumulations in fluvial environments requires 103-106 or even greater times concentration of heavy minerals. For this to occur, regular sediment supply from erosion of adjacent topography is required, the river should remain within a single course for an extended period of time and the material must be reworked such that a high proportion of the sediment is removed while a high proportion of the heavy minerals remains. We use numerical modeling, constrained by observations of circum-Pacific placer gold deposits, to explore processes occurring in evolving river systems in dynamic tectonic environments. A fluvial erosion/transport model is used to determine the mobility of placer gold under variable uplift rate, storm intensity, and rock mass strength conditions. Gold concentration is calculated from hydraulic and bedload grain size conditions. Model results suggest that optimal gold concentration occurs in river channels that frequently approach a threshold between detachment-limited and transport-limited hydraulic conditions. Such a condition enables the accumulation of gold particles within the framework of a residual gravel lag. An increase in transport capacity, which can be triggered by faster uplift rates, more resistant bedrock, or higher intensity storm events, will strip all bedload from the channel. Conversely, a reduction in transport capacity, triggered by a reduction in uplift rate, bedrock resistance, or storm intensity, will lead to a greater accumulation of a majority of sediments and a net decrease in gold concentration. For our model parameter range, the optimal conditions for placer gold concentration are met by 103 times difference in strength between bedrock and fault, uplift rates between 1 and 5 mm a-1, and moderate storm intensities. Fault damage networks are shown to be a critical factor for high Au concentrations and should be a target for exploration.

Submarine Landslide Hazards Offshore Southern Alaska: Seismic Strengthening Versus Rapid Sedimentation

NASA Astrophysics Data System (ADS)

Sawyer, D.; Reece, R.; Gulick, S. P. S.; Lenz, B. L.

2017-12-01

The southern Alaskan offshore margin is prone to submarine landslides and tsunami hazards due to seismically active plate boundaries and extreme sedimentation rates from glacially enhanced mountain erosion. We examine the submarine landslide potential with new shear strength measurements acquired by Integrated Ocean Drilling Program Expedition 341 on the continental slope and Surveyor Fan. These data reveal lower than expected sediment strength. Contrary to other active margins where seismic strengthening enhances slope stability, the high-sedimentation margin offshore southern Alaska behaves like a passive margin from a shear strength perspective. We interpret that seismic strengthening occurs but is offset by high sedimentation rates and overpressure within the slope and Surveyor Fan. This conclusion is supported because shear strength follows an expected active margin profile outside of the fan, where background sedimentation rates occur. More broadly, seismically active margins with wet-based glaciers are susceptible to submarine landslide hazards because of the combination of high sedimentation rates and earthquake shaking

Comparison of elemental accumulation rates between ferromanganese deposits and sediments in the South Pacific Ocean

USGS Publications Warehouse

Kraemer, T.; Schornick, J.C.

1974-01-01

Rates of accumulation of Fe and Mn, as well as Cu, Ni, Co, Pb, Zn, Hg, U and Th have been determined for five ferromanganese deposits from four localities in the South Pacific Ocean. Manganese is accumulating in nodules and crusts at a rate roughly equivalent to that found to be accumulating in sediments in the same area. Iron shows a deficiency in accumulation in nodules and crusts with respect to sediments, especially near the continents, but also in the central and south-central Pacific. Copper is accumulating in nodules and crusts at a rate one order of magnitude less than the surrounding sediments. This is interpreted as meaning that most of the Mn is supplied as an authigenic phase to both sediments and nodules while Fe is supplied mostly by ferromanganese micro-nodules and by detrital and adsorbed components of sediments; and Cu is enriched in sediments relative to nodules and crusts most probably through biological activity. ?? 1974.

Response of bed surface patchiness to reductions in sediment supply

NASA Astrophysics Data System (ADS)

Nelson, Peter A.; Venditti, Jeremy G.; Dietrich, William E.; Kirchner, James W.; Ikeda, Hiroshi; Iseya, Fujiko; Sklar, Leonard S.

2009-06-01

River beds are often arranged into patches of similar grain size and sorting. Patches can be distinguished into "free patches," which are zones of sorted material that move freely, such as bed load sheets; "forced patches," which are areas of sorting forced by topographic controls; and "fixed patches" of bed material rendered immobile through localized coarsening that remain fairly persistent through time. Two sets of flume experiments (one using bimodal, sand-rich sediment and the other using unimodal, sand-free sediment) are used to explore how fixed and free patches respond to stepwise reductions in sediment supply. At high sediment supply, migrating bed load sheets formed even in unimodal, sand-free sediment, yet grain interactions visibly played a central role in their formation. In both sets of experiments, reductions in supply led to the development of fixed coarse patches, which expanded at the expense of finer, more mobile patches, narrowing the zone of active bed load transport and leading to the eventual disappearance of migrating bed load sheets. Reductions in sediment supply decreased the migration rate of bed load sheets and increased the spacing between successive sheets. One-dimensional morphodynamic models of river channel beds generally are not designed to capture the observed variability, but should be capable of capturing the time-averaged character of the channel. When applied to our experiments, a 1-D morphodynamic model (RTe-bookAgDegNormGravMixPW.xls) predicted the bed load flux well, but overpredicted slope changes and was unable to predict the substantial variability in bed load flux (and load grain size) because of the migration of mobile patches. Our results suggest that (1) the distribution of free and fixed patches is primarily a function of sediment supply, (2) the dynamics of bed load sheets are primarily scaled by sediment supply, (3) channels with reduced sediment supply may inherently be unable to transport sediment uniformly across their width, and (4) cross-stream variability in shear stress and grain size can produce potentially large errors in width-averaged sediment flux calculations.

Natural radioactivity investigation in Dam sediments of northeast Algeria using gamma spectroscopy

NASA Astrophysics Data System (ADS)

Benrachi, Fatima; Bouhila, Ghania; Saadi, Asma; Ramdhane, Mourad

2017-09-01

Current research paper intends to estimate the natural radioactivity levels in sediments samples collected from Beni Haroun Dam in the northeast Algeria, using high resolution HPGe detector. The mean activity concentrations values measured for the radionuclides 232Th, 226Ra and 40K are 18.9 ± 1.9, 37.3 ± 2.7 and 149.9 ± 5.5 Bq/kg, respectively. The 137Cs anthropogenic radionuclide has been observed with maximum activity concentration value of 0.8 ± 0.4 Bq/kg, which is considered an insignificant amount. In order to assess the radiological threat of gamma radiations emitted by these radionuclides on the health of the population, absorbed dose rate, annual effective dose equivalent and radiation hazard indices were had been calculated. The obtained values are compared with the world wide average ones.

Near bed suspended sediment flux by single turbulent events

NASA Astrophysics Data System (ADS)

Amirshahi, Seyed Mohammad; Kwoll, Eva; Winter, Christian

2018-01-01

The role of small scale single turbulent events in the vertical mixing of near bed suspended sediments was explored in a shallow shelf sea environment. High frequency velocity and suspended sediment concentration (SSC; calibrated from the backscatter intensity) were collected using an Acoustic Doppler Velocimeter (ADV). Using quadrant analysis, the despiked velocity time series was divided into turbulent events and small background fluctuations. Reynolds stress and Turbulent Kinetic Energy (TKE) calculated from all velocity samples, were compared to the same turbulent statistics calculated only from velocity samples classified as turbulent events (Reevents and TKEevents). The comparison showed that Reevents and TKEevents was increased 3 and 1.6 times, respectively, when small background fluctuations were removed and that the correlation with SSC for TKE could be improved through removal of the latter. The correlation between instantaneous vertical turbulent flux (w ‧) and SSC fluctuations (SSC ‧) exhibits a tidal pattern with the maximum correlation at peak ebb and flood currents, when strong turbulent events appear. Individual turbulent events were characterized by type, strength, duration and length. Cumulative vertical turbulent sediment fluxes and average SSC associated with individual turbulent events were calculated. Over the tidal cycle, ejections and sweeps were the most dominant events, transporting 50% and 36% of the cumulative vertical turbulent event sediment flux, respectively. Although the contribution of outward interactions to the vertical turbulent event sediment flux was low (11%), single outward interaction events were capable of inducing similar SSC ‧ as sweep events. The results suggest that on time scales of tens of minutes to hours, TKE may be appropriate to quantify turbulence in sediment transport studies, but that event characteristics, particular the upward turbulent flux need to be accounted for when considering sediment transport on process time scales.

Temporal variability and memory in sediment transport in an experimental step-pool channel

NASA Astrophysics Data System (ADS)

Saletti, Matteo; Molnar, Peter; Zimmermann, André; Hassan, Marwan A.; Church, Michael

2015-11-01

Temporal dynamics of sediment transport in steep channels using two experiments performed in a steep flume (8%) with natural sediment composed of 12 grain sizes are studied. High-resolution (1 s) time series of sediment transport were measured for individual grain-size classes at the outlet of the flume for different combinations of sediment input rates and flow discharges. Our aim in this paper is to quantify (a) the relation of discharge and sediment transport and (b) the nature and strength of memory in grain-size-dependent transport. None of the simple statistical descriptors of sediment transport (mean, extreme values, and quantiles) display a clear relation with water discharge, in fact a large variability between discharge and sediment transport is observed. Instantaneous transport rates have probability density functions with heavy tails. Bed load bursts have a coarser grain-size distribution than that of the entire experiment. We quantify the strength and nature of memory in sediment transport rates by estimating the Hurst exponent and the autocorrelation coefficient of the time series for different grain sizes. Our results show the presence of the Hurst phenomenon in transport rates, indicating long-term memory which is grain-size dependent. The short-term memory in coarse grain transport increases with temporal aggregation and this reveals the importance of the sampling duration of bed load transport rates in natural streams, especially for large fractions.

Small ecosystem engineers as important regulators of lake's sediment respiration.

NASA Astrophysics Data System (ADS)

Baranov, Victor; Lewandowski, Joerg; Krause, Stefan; Romeijn, Paul

2016-04-01

Although shallow lakes are covering only about 1.5% of the land surface of the Earth, they are responsible for sequestration of carbon amounts similar or even larger than those sequestered in all marine sediments. One of the most important drivers of the carbon sequestration in lakes is sediment respiration. Especially in shallow lakes, bioturbation, i.e. the biogenic reworking of the sediment matrix and the transport of fluids within the sediment, severely impacts on sediment respiration. Widespread freshwater bioturbators such as chironomid larvae (Diptera, Chironomidae) are building tubes in the sediment and actively pump water through their burrows (ventilation). In the present work we study how different organism densities and temperatures (5-30°C) impact on respiration rates. In a microcosm experiment the bioreactive resazurin/resorufin smart tracer system was applied for quantifying the impacts of different densities of Chironomidae (Diptera) larvae (0, 1000, 2000 larvae/m2) on sediment respiration. Tracer transformation rates (and sediment respiration) were correlated with larval densities with highest transformation rates occurring in microcosms with highest larval densities. Respiration differences between defaunated sediment and sediment with 1000 and 2000 larvae per m2 was insignificant at 5 °C, and was progressively increasing with rising temperatures. At 30 °C respiration rates of sediment with 2000 larvae per m2 was 4.8 times higher than those of defaunated sediment. We interpret this as an effect of temperature on larval metabolic and locomotory activity. Furthermore, bacterial communities are benefiting from the combination of the high water temperatures and bioirrigation as bacterial community are able to maintain high metabolic rates due to oxygen supplied by bioirrigation. In the context of global climate change that means that chironomid ecosystem engineering activity will have a profound and increasing impact on lake sediment respiration and carbon sequestration due to a warming world.

Effect of high sedimentation rates on surface sediment dynamics and mangrove growth in the Porong River, Indonesia.

PubMed

Sidik, Frida; Neil, David; Lovelock, Catherine E

2016-06-15

Large quantities of mud from the LUSI (Lumpur Sidoarjo) volcano in northeastern Java have been channeled to the sea causing high rates of sediment delivery to the mouth of the Porong River, which has a cover of natural and planted mangroves. This study investigated how the high rates of sediment delivery affected vertical accretion, surface elevation change and the growth of Avicennia sp., the dominant mangrove species in the region. During our observations in 2010-2011 (4-5years after the initial volcanic eruption), very high rates of sedimentation in the forests at the mouth of the river gave rise to high vertical accretion of over 10cmy(-1). The high sedimentation rates not only resulted in reduced growth of Avicennia sp. mangrove trees at the two study sites at the Porong River mouth, but also gave rise to high soil surface elevation gains. Copyright © 2016 Elsevier Ltd. All rights reserved.

Southern Appalachian hillslope erosion rates measured by soil and detrital radiocarbon in hollows

Treesearch

T.C. Hales; K.M. Scharer; R.M. Wooten

2012-01-01

Understanding the dynamics of sediment generation and transport on hillslopes provides important constraints on the rate of sediment output from orogenic systems. Hillslope sediment fluxes are recorded by organic material found in the deposits infilling unchanneled convergent topographic features called hollows. This study describes the first hollow infilling rates...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2010 CFR

2010-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2014 CFR

2014-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2012 CFR

2012-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2011 CFR

2011-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2013 CFR

2013-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

Application of dimensionless sediment rating curves to predict suspended-sediment concentrations, bedload, and annual sediment loads for rivers in Minnesota

USGS Publications Warehouse

Ellison, Christopher A.; Groten, Joel T.; Lorenz, David L.; Koller, Karl S.

2016-10-27

Consistent and reliable sediment data are needed by Federal, State, and local government agencies responsible for monitoring water quality, planning river restoration, quantifying sediment budgets, and evaluating the effectiveness of sediment reduction strategies. Heightened concerns about excessive sediment in rivers and the challenge to reduce costs and eliminate data gaps has guided Federal and State interests in pursuing alternative methods for measuring suspended and bedload sediment. Simple and dependable data collection and estimation techniques are needed to generate hydraulic and water-quality information for areas where data are unavailable or difficult to collect.The U.S. Geological Survey, in cooperation with the Minnesota Pollution Control Agency and the Minnesota Department of Natural Resources, completed a study to evaluate the use of dimensionless sediment rating curves (DSRCs) to accurately predict suspended-sediment concentrations (SSCs), bedload, and annual sediment loads for selected rivers and streams in Minnesota based on data collected during 2007 through 2013. This study included the application of DSRC models developed for a small group of streams located in the San Juan River Basin near Pagosa Springs in southwestern Colorado to rivers in Minnesota. Regionally based DSRC models for Minnesota also were developed and compared to DSRC models from Pagosa Springs, Colorado, to evaluate which model provided more accurate predictions of SSCs and bedload in Minnesota.Multiple measures of goodness-of-fit were developed to assess the effectiveness of DSRC models in predicting SSC and bedload for rivers in Minnesota. More than 600 dimensionless ratio values of SSC, bedload, and streamflow were evaluated and delineated according to Pfankuch stream stability categories of “good/fair” and “poor” to develop four Minnesota-based DSRC models. The basis for Pagosa Springs and Minnesota DSRC model effectiveness was founded on measures of goodness-of-fit that included proximity of the model(s) fitted line to the 95-percent confidence intervals of the site-specific model, Nash-Sutcliffe Efficiency values, model biases, and deviation of annual sediment loads from each model to the annual sediment loads calculated from measured data.Composite plots comparing Pagosa Springs DSRCs, Minnesota DSRCs, site-specific regression models, and measured data indicated that regionally developed DSRCs (Minnesota DSRC models) more closely approximated measured data for nearly every site. Pagosa Springs DSRC models had markedly larger exponents (slopes) when compared to the Minnesota DSRC models and the site-specific regression models, and over-represent SSC and bedload at streamflows exceeding bankfull. The Nash-Sutcliffe Efficiency values for the Minnesota DSRC model for suspended-sediment concentrations closely matched Nash-Sutcliffe Efficiency values of the site-specific regression models for 12 out of 16 sites. Nash-Sutcliffe Efficiency values associated with Minnesota DSRCs were greater than those associated with Pagosa Springs DSRCs for every site except the Whitewater River near Beaver, Minnesota site. Pagosa Springs DSRC models were less accurate than the mean of the measured data at predicting SSC values for one-half of the sites for good/fair stability sites and one-half of the sites for poor stability sites. Relative model biases were calculated and determined to be substantial (greater than 5 percent) for Pagosa Springs and Minnesota models, with Minnesota models having a lower mean model bias. For predicted annual suspended-sediment loads (SSL), the Minnesota DSRC models for good/fair and poor stream stability sites more closely approximated the annual SSLs calculated from the measured data as compared to the Pagosa Springs DSRC model.Results of data analyses indicate that DSRC models developed using data collected in Minnesota were more effective at compensating for differences in individual stream characteristics across a variety of basin sizes and flow regimes than DSRC models developed using data collected for Pagosa Springs, Colorado. Minnesota DSRC models retained a substantial portion of the unique sediment signatures for most rivers, although deviations were observed for streams with limited sediment supply and for rivers in southeastern Minnesota, which had markedly larger regression exponents. Compared to Pagosa Springs DSRC models, Minnesota DSRC models had regression slopes that more closely matched the slopes of site-specific regression models, had greater Nash-Sutcliffe Efficiency values, had lower model biases, and approximated measured annual sediment loads more closely. The results presented in this report indicate that regionally based DSRCs can be used to estimate reasonably accurate values of SSC and bedload.Practitioners are cautioned that DSRC reliability is dependent on representative measures of bankfull streamflow, SSC, and bedload. It is, therefore, important that samples of SSC and bedload, which will be used for estimating SSC and bedload at the bankfull streamflow, are collected over a range of conditions that includes the ascending and descending limbs of the event hydrograph. The use of DSRC models may have substantial limitations for certain conditions. For example, DSRC models should not be used to predict SSC and sediment loads for extreme streamflows, such as those that exceed twice the bankfull streamflow value because this constitutes conditions beyond the realm of current (2016) empirical modeling capability. Also, if relations between SSC and streamflow and between bedload and streamflow are not statistically significant, DSRC models should not be used to predict SSC or bedload, as this could result in large errors. For streams that do not violate these conditions, DSRC estimates of SSC and bedload can be used for stream restoration planning and design, and for estimating annual sediment loads for streams where little or no sediment data are available.

Taking a step back: Himalayan erosion as seen from Bangladesh

NASA Astrophysics Data System (ADS)

Lupker, M.; France-Lanord, C.; Lavé, J.; Blard, P.; Galy, V.

2012-12-01

The Himalayan range represents the archetype of mountain building and is considered in many studies as the locus of intense interactions between climate, denudation and tectonics. A better understanding of these interactions requires that the flux of material removed from the system through erosion is known. The products of Himalayan erosion are exported to the Bengal fan and the Indian Ocean by two major rivers: the Ganga and Brahmaputra. These rivers provide the opportunity to quantify the Himalayan denudation rates as they integrate surface and tectonic processes across the entire basin. Basin wide erosion or denudation rates have classically been derived from the gauging of sediments fluxes. By coping with the inherent spatial and temporal variability of sediment concentration in rivers, sediment budgets yield average denudation rate over the observational period ranging from years to decades. Cosmogenic nuclides such as 10-Be allow the estimation of basin-wide denudation rates averaged over typical time scales of hundreds to thousand of years, from a single measurement in river sediments. We compare these methods for the case of the Ganga basin that drains the central part of the Himalayan range. By using a distal point of view, i.e. by sampling and evaluating the sediment flux at the outlet of the Ganga in Bangladesh we are able to propose an average denudation rate of the entire, central part of the Himalayan range. This sampling location offers the benefit of integrating the entire basin and its distance from the sediment source makes it also less prone to perturbations in the headwaters. However, the effects of 500 to 1000 km floodplain transfer on the sedimentary signal needs to be correctly evaluated. The gauged sediment flux can mainly be impacted by the sequestration of sediments in the floodplain. For the Ganga basin, sequestration is limited to ca. 10 % of the eroded sediment flux as deduced from geochemical mass balance approaches [1]. On their side, cosmogenic derived denudation rates in Bangladesh may also be biased by the exposure to cosmic-rays during sediment transfer in the floodplain. The comparison of the 10-Be concentration of sediments in the main Himalayan Rivers, upstream of the floodplain with sediments in Bangladesh and the use of modeling approaches suggests that this effect is nearly negligible [2]. The 10-Be concentration in sediments sampled in Bangladesh can therefore be used to infer the denudation rate of the entire range drained by the basin. Gauged sediment fluxes and 10-Be in sediments constrain the Himalayan denudation rate to ca. 0.8 and 1.0 mm/yr, respectively. Both independent methods yield similar denudations rates. However the uncertainties on both methods remain high, which does not allow us to speculate on the origin of the small difference between both rates. [1] Lupker et al., 2011 - JGR Earth Surf. 116 [2] Lupker et al., 2012 - EPSL 333-334 - p146:156

What Is the Role of Land-Use Compositions and Spatial Configurations in Sediment Yield from Mountainous Watershed?

NASA Astrophysics Data System (ADS)

Shi, Z. H.

2014-12-01

There are strong ties between land use and sediment yield in watersheds. Many studies have used multivariate regression techniques to explore the response of sediment yield to land-use compositions and spatial configurations in watersheds. However, one issue with the use of conventional statistical methods to address relationships between land-use compositions and spatial configurations and sediment yield is multicollinearity. This paper examines the combined effects of land-use compositions and land-use spatial configurations of the watershed on the specific sediment yield of the Upper Du River watershed (8,973 km2) in China using the Soil and Water Assessment Tool (SWAT) and partial least-squares regression (PLSR). The land-use compositions and spatial configurations of the watershed were calculated at the sub-watershed scale. The sediment yields from sub-watershed were evaluated using SWAT model. The first-order factors were identified by calculating the variable importance for the projection (VIP). The results revealed that the land-use compositions exerted the largest effects on the specific sediment yield and explained 61.2% of the variation in the specific sediment yield. Land-use spatial configurations were also found to have a large effect on the specific sediment yield and explained 21.7% of the observed variation in the specific sediment yield. The following are the dominant first-order factors of the specific sediment yield at the sub-watershed scale: the areal percentages of agriculture and forest, patch density, value of the Shannon's diversity index, contagion. The VIP values suggested that the Shannon's diversity index and contagion are important factors for sediment delivery.

Using ²¹⁰Pb measurements to estimate sedimentation rates on river floodplains.

PubMed

Du, P; Walling, D E

2012-01-01

Growing interest in the dynamics of floodplain evolution and the important role of overbank sedimentation on river floodplains as a sediment sink has focused attention on the need to document contemporary and recent rates of overbank sedimentation. The potential for using the fallout radionuclides ¹³⁷Cs and excess ²¹⁰Pb to estimate medium-term (10-10² years) sedimentation rates on river floodplains has attracted increasing attention. Most studies that have successfully used fallout radionuclides for this purpose have focused on the use of ¹³⁷Cs. However, the use of excess ²¹⁰Pb potentially offers a number of advantages over ¹³⁷Cs measurements. Most existing investigations that have used excess ²¹⁰Pb measurements to document sedimentation rates have, however, focused on lakes rather than floodplains and the transfer of the approach, and particularly the models used to estimate the sedimentation rate, to river floodplains involves a number of uncertainties, which require further attention. This contribution reports the results of an investigation of overbank sedimentation rates on the floodplains of several UK rivers. Sediment cores were collected from seven floodplain sites representative of different environmental conditions and located in different areas of England and Wales. Measurements of excess ²¹⁰Pb and ¹³⁷Cs were made on these cores. The ²¹⁰Pb measurements have been used to estimate sedimentation rates and the results obtained by using different models have been compared. The ¹³⁷Cs measurements have also been used to provide an essentially independent time marker for validation purposes. In using the ²¹⁰Pb measurements, particular attention was directed to the problem of obtaining reliable estimates of the supported and excess or unsupported components of the total ²¹⁰Pb activity of sediment samples. Although there was a reasonable degree of consistency between the estimates of sedimentation rate provided by the ¹³⁷Cs and excess ²¹⁰Pb measurements, some differences existed and the various models used to interpret excess ²¹⁰Pb measurements could produce different results. By using the ¹³⁷Cs measurements to provide independent validation of the estimates of sedimentation rate provided by the different models used with the excess ²¹⁰Pb measurement it was shown that the CICCS and Composite CRS models appeared to generally provide the best results. Copyright © 2011 Elsevier Ltd. All rights reserved.

Loads of suspended sediment and nutrients from local nonpoint sources to the tidal Potomac River and Estuary, Maryland and Virginia, 1979-81 water years

USGS Publications Warehouse

Hickman, R. Edward

1987-01-01

Loads of suspended sediment, phosphorus, nitrogen, biochemical oxygen demand, and dissolved silica discharged to the tidal Potomac River and Estuary during the !979-81 water years from three local nonpoint sources have been calculated. The loads in rain falling directly upon the tidal water surface and from overflows of the combined sewer system of the District of Columbia were determined from available information. Loads of materials in the streamflow from local watersheds draining directly to the tidal Potomac River and Estuary downstream from Chain Bridge in Washington, D.C., were calculated from samples of streamflow leaving five monitored watersheds. Average annual yields of substances leaving three urban watersheds (Rock Creek and the Northwest and Northeast Branches of the Anacostia River) and the rural Saint Clements Creek watershed were calculated either by developing relationships between concentration and streamflow or by using the mean of measured concentrations. Yields calculated for the 1979-81 water years are up to 2.3 times period-of-record yields because of greater than average streamflow and stormflow during this 3-year period. Period-of-record yields of suspended sediment from the three urban watersheds and the Saint Clements Creek watershed do not agree with yields reported by other studies. The yields from the urban watersheds are 17 to 51 percent of yields calculated using sediment-concentration data collected during the 1960-62 water years. Previous studies suggest that this decrease is at least partly due to the imposition of effective sediment controls at construction sites and to the construction of two multipurpose reservoirs. The yield calculated for the rural Saint Clements Creek watershed is at least twice the yields calculated for other rural watersheds, a result that may be due to most of the samples of this stream being taken during the summer of the 1981 water year, a very dry period. Loads discharged from all local tributary watersheds to the tidal Potomac River and Estuary during the 1979-81 water years were calculated by applying to the unsampled watersheds the yields determined for the monitored watersheds. The resulting loads are 2.7 million megagrams of suspended sedi- ment, 3,100 megagrams of phosphorus, 14,000 megagrams of nitrogen, 74,000 megagrams of ultimate biochemical oxygen demand, and 68,000 megagrams of dissolved silica. The value for the load of sediment is probably an overestimate because the sediment yield calculated for the Saint Clements Creek watershed does not appear to be representative of rural watersheds. Summed, the loads discharged from all local nonpoint sources (local tributary watersheds, rainfall, and combined sewer overflows) to the tidal Potomac River and Estuary during the 1979-81 water years are 2.7 million megagrams of suspended sediment, 3,300 megagrams of phosphorus, 18,000 megagrams of nitrogen, 78,000 megagrams of ultimate biochemical oxygen demand, and 69,000 megagrams of dissolved silica. These loads accounted for 17 to 38 percent of the loads discharged by major sources during this period.

Sediment Dating With 210Pb and 137Cs In Monterey Canyon, California Reveal the extent of recent sediment movement down canyon

NASA Astrophysics Data System (ADS)

Lorenson, T. D.; Maier, K. L.; Gwiazda, R.; Paull, C. K.; McGann, M.

2017-12-01

Submarine canyons are major vectors of sediment transport off the continent into the deep sea. Recent results from the Monterey Coordinated Canyon Experiment document fifteen sediment transport events occurred during an 18-month period from 2015 to 2017, and three of them reached at least to 1850m. In an attempt to constrain the timing and rate in which sediments were transported down canyons in these and earlier events we have collected sediment cores and measured the sedimentation rates using 210Pb and 137Cs dating techniques along the axis of Monterey Canyon. We employed transects of precisely located ROV collected push cores and vibracores collected at water depths ranging from 300m to 2900m perpendicular to the canyon axis using a remotely operated vehicle (ROV). Some cores were taken in 2013 and compared with those taken in 2017. We focused on cores from terraces that are between 60m and 75m above the canyon thalweg in water depths between 300 and 1500 m and in cores collected form the canyon's axial channel between 1800 and 2900 m water depths where the canyon widens considerably. Generally sedimentation rates vary with depth, with the highest sedimentation rate closest to land, but vary substantially across successive terraces. Sawtooth-shaped excess 210Pb and 137Cs profiles with depth at almost all sites at least to 1500m imply several episodes of deposition and reworking of sediment on the terraces suggesting multiple sediment transport events. The excess 210Pb in many cores reach depths of up to 1m implying sedimentation rates greater than 10mm per year. At the deepest site (2900m) about 10 cm of fine hemipelagic sediment overlies sand indicating a high-energy sediment flow event. In 2014 the measured 210Pb sedimentation rate of 0.6 to 0.8mm per year indicates that the last 10 cm of sediment have been deposited and undisturbed since about the year 1910 showing that recent events have not reached this depth. Measurements are on going to determine if the 2015-2017 sediment transport events have travelled down to 2900m [RG1] and if the timing of these sediment flow events were triggered by external factors, like earthquakes, winter storms, or by seafloor failures within the Canyon. [RG1]This seem to contradict the previous sentence where it says that it did not reach 2900 m

New estimated Holocene denudation rates for non-glaciated areas in the southernmost Patagonian Andes (53°S), Chile

NASA Astrophysics Data System (ADS)

Breuer, Sonja; Kilian, Rolf; Baeza, Oscar; Arz, Helge

2010-05-01

Cenozoic denudation rates are sparsely known for the southernmost Patagonian Andes. One of the scientific approaches is to calculate long-term denudation rates based on fission track analyses. Though, these average rates comprise a long period with distinct climate conditions and very different extend of glaciation. These integrated denudation rates include extensive surface areas with different morphological, glacial and vegetational properties. In contrast, our approach is restricted to relative short Holocene periods and small catchment areas, for which the denudation and its controlling surface characteristics could be defined more precisely. Thus a more precise evaluation of the influencing parameters like climate, morphology and vegetation cover was possible. We concentrated on three restricted and nearly closed areas of denudation and accumulation. In those catchments we determined the sediment masses of lakes, based on sediment drilling, echosounding and computer based interpolation of the siliciclastic sediment masses. These masses were transferred to the denudation areas which have been characterised and measured by remote sensing. The westernmost Tamar Lake is located on the Tamar Island in the western part of the Magellan Strait, where the annual precipitation is about 4,000 mm. The catchment area has a dense vegetation cover. The lake surrounding slopes reach an elevation of 400 m a.s.l and they are up to 60° steep. The calculated denudation rate for this catchment is about 2.56 mm/ka, which represents a minimum value, because the postglacial weathering horizon is only partly removed into the lake. The highest elevated lake Muy Profundo (500 m a.s.l.) possesses a denudation area with a nearly vegetation-free zone up to 750 m a.s.l. within the Patagonian Batholith. The catchment area of this lake is characterised by a roche moutonnée landform with steep slopes and active fracture zones. The precipitation varies between 5,000 and 8,000 mm/a. The denudation rates of the catchment amount to 0.42 mm/ka. Despite the high precipitation and the exposed position this denudation rate is unexpectedly low. Along the active fracture zones a stronger denudation could be observed by the occurrence of restricted gullies. The removed predominantly coarse clastic material is stored in alluvial cones and not included in our mass balance. The elevation of the catchment of the easternmost Chandler does not exceed 200 m a.s.l. and the area is characterised by a moderate relief with relatively flat slopes. The roche moutonnée landscape is interspersed with tracts of peat land and Magellanic rainforest. The precipitation ranges between 3,500 and 5,000 mm/a. Circulating acid soil water cause an intense chemical weathering and formed a 10-20 cm thick weathering horizon at the interface between bedrock and peaty soil. Due to the sediment core and the echosound stratigraphy, the denudation could be determined for two periods of time. The 2,040 cal. a BP tephra layer of the Mt. Burney volcano is the most distinct reflector in the echosound data. Therefore it was used as a sedimentation boundary. The denudation rates for the period 12,100 to ~2,000 and for the last 2000 years are very similar with ~2.55 mm/ka. On the basis of e.g. Ti/U enrichment in the weathering horizon, we conclude that the chemical denudation is very important in areas with vegetation cover in the superhumid Andes. In a long-term perspective, the relatively high denudation rates of low elevated peat land compared to the exposed rock surfaces may further increase the relief even during interglacial periods, like the Holocene. On the basis of our results we could state that the precipitation plays only a subordinated role as a control mechanism concerning the denudation in ice-free, but low temperate areas of the Patagonian Andes.

Temporal pattern and memory in sediment transport in an experimental step-pool channel

NASA Astrophysics Data System (ADS)

Saletti, Matteo; Molnar, Peter; Zimmermann, André; Hassan, Marwan A.; Church, Michael; Burlando, Paolo

2015-04-01

In this work we study the complex dynamics of sediment transport and bed morphology in steep streams, using a dataset of experiments performed in a steep flume with natural sediment. High-resolution (1 sec) time series of sediment transport were measured for individual size classes at the outlet of the flume for different combinations of sediment input rates, discharges, and flume slopes. The data show that the relation between instantaneous discharge and sediment transport exhibits large variability on different levels. After dividing the time series into segments of constant water discharge, we quantify the statistical properties of transport rates by fitting the data with a Generalized Extreme Value distribution, whose 3 parameters are related to the average sediment flux. We analyze separately extreme events of transport rate in terms of their fractional composition; if only events of high magnitude are considered, coarse grains become the predominant component of the total sediment yield. We quantify the memory in grain size dependent sediment transport with variance scaling and autocorrelation analyses; more specifically, we study how the variance changes with different aggregation scales and how the autocorrelation coefficient changes with different time lags. Our results show that there is a tendency to an infinite memory regime in transport rate signals, which is limited by the intermittency of the largest fractions. Moreover, the structure of memory is both grain size-dependent and magnitude-dependent: temporal autocorrelation is stronger for small grain size fractions and when the average sediment transport rate is large. The short-term memory in coarse grain transport increases with temporal aggregation and this reveals the importance of the sampling frequency of bedload transport rates in natural streams, especially for large fractions.

Flux and accumulation of sedimentary particles off the continental slope of Pakistan: a comparison of water column and seafloor estimates from the oxygen minimum zone, NE Arabian Sea

NASA Astrophysics Data System (ADS)

Schulz, H.; von Rad, U.

2013-07-01

Due to the lack of bioturbation, the laminated muds from the oxygen-minimum zone (OMZ) off Pakistan provide a unique opportunity to precisely determine the vertical and lateral sediment fluxes in the near shore part of the northeastern Arabian Sea, and to explore the effects of the margin topography and the low oxygen conditions on the accumulation of organic matter and other particles. West of Karachi, in the Hab river area of EPT and WPT (Eastern and Western PAKOMIN Traps), 16 short sediment profiles from water depths between 250 m and 1970 m on a depth transect crossing the OMZ (~ 120 to ~ 1200 m water depth) were investigated, and correlated on the basis of a thick, light-gray- to reddish-colored turbidite layer. Varve counting yielded a date for this layer of AD 1905 to 1888. We adopted the young age which agrees with 210Pb- dating, and used this isochronous stratigraphic marker bed to calculate sediment accumulation rates, that we could directly compare with the flux rates from the sediment traps installed within the water column above. All traps in the area show exceptionally high, pulsed winter fluxes of up to 5000 mg m-2 d-1 in this margin environment. The lithic flux at the sea floor is as high as 4000 mg m-2 d-1 , and agrees remarkably well with the bulk winter flux of material. This holds as well for the individual bulk components (organic carbon, calcium carbonate, opal, lithic fraction). However, the high winter flux events (HFE) by their extreme mass of remobilized matter terminated the recording in the shallow traps by clogging the funnels. Based on our comparisons, we argue that HFE for the past 5000 yr most likely occurred as regular events within the upper OMZ off Pakistan. Coarse fraction and foraminiferal accumulation rates from sediment surface samples along the Hab transect show distribution patterns that seem to be a function of water depth and distance from the shelf. Some of these sediment fractions show sudden shifts at the lower boundary of the OMZ. However, the potential effect of the OMZ on carbon preservation in the area would by masked by high mass of fine-grained matter laterally advected, and by the pulsed nature of the resuspension events.

Fallout isotope chronology of the near-surface sediment record of Lake Bolătău.

PubMed

Bihari, Árpád; Karlik, Máté; Mîndrescu, Marcel; Szalai, Zoltán; Grădinaru, Ionela; Kern, Zoltán

2018-01-01

Fallout isotope ( 210 Pb ex, 137 Cs and 241 Am) based dating has been carried out on the near-surface sediment core collected from Lake Bolătău-Feredeu (Bukovina, Romania). The motivation was to improve the chronology of this recent section in connection with significant fluctuations observed in sediment accumulation rates, particle size distribution and primordial radioisotope (i.e. 40 K and 232 Th) composition. Previously only an extrapolation of a broad-range OxCal age-depth model, which was based on 8 AMS radiocarbon dates from the deeper part of a parallel sediment sequence and tentatively validated for the upper part using the double peaks of the 137 Cs activity concentration distribution, was available for the studied section (1-24 cm). Parallel to the previous 137 Cs measurement, 210 Pb and 226 Ra (for a more detailed, 210 Pb ex -based chronology), 241 Am (for an additional time-marker), as well as 40 K and 232 Th concentrations have also been determined by gamma-spectrometry. In case of the 210 Pb ex -based chronology, due to a large deviation from a pure exponential distribution, the Constant Flux (CF) model has been used for the calculation of sediment ages and accumulation rates. Although the broad-range OxCal and the CF model were broadly similar down to 22 cm, the 210 Pb ex -based ages are clearly superior in terms of uncertainty in the uppermost 12 cm, while the broad-range model has smaller uncertainty below 20 cm (>150 years). The CF model gave an average mass accumulation rate of (0.08 ± 0.03) g cm -2 yr -1 for sections 0-11 cm, and (0.03 ± 0.01) g cm -2 yr -1 for sections 12-22 cm, respectively. Significant changes have been observed in the depth distribution of both the particle size distribution and the elemental/isotopic composition of the sediment record, most likely related to the variation observable in the intensity and volume of precipitation in the catchment. The obtained high-resolution records of Lake Bolătău, including multiple radioisotopes, can serve as a regional benchmark for similar studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soil surface lowering due to soil erosion in villages near Lake Victoria, Uganda

NASA Astrophysics Data System (ADS)

de Meyer, A.; Deckers, J.; Poesen, J.; Isabirye, M.

2009-04-01

In the effort to pinpoint the sources of sediment pollution in Lake Victoria, the contribution of sedi-ment from compounds, landing sites, main roads and footpaths is determined in the catchment of Na-bera Bay and Kafunda Bay at the northern shore of Lake Victoria in southern Uganda. The amount of soil loss in compounds and landing sites is determined by the reconstruction of the original and current soil surface according to botanical and man-made datable objects. The soil erosion rate is then deter-mined by dividing the eroded soil volume (corrected for compaction) by the age of the oldest datable object. In the study area, the average soil erosion rate in compounds amounts to 107 Mg ha-1 year-1 (per unit compound) and in landing sites to 207 Mg ha-1 year-1 (per unit landing site). Although com-pounds and landing sites occupy a small area of the study area (1.1 %), they are a major source of sediment to Lake Victoria (63 %). The soil loss on footpaths and main roads is calculated by multip-lying the total length of footpaths and main roads with the average width and depth (measured towards a reference surface). After the correction for compaction is carried out, the soil erosion rate on foot-paths amounts to 34 Mg ha-1 year-1 and on main roads to 35 Mg ha-1 year-1. Also footpaths and main roads occupy a small area of the study area (1.1 %), but contribute disproportionately to the total soil loss in the catchment (22 %). In this research, the information about the village/compound given by the villager/owner is indispensable. In accordance to an adaptation of the model of McHugh et al. (2002), 32 % of the sediment that is generated in the catchment, is deposited in Lake Victoria (i.e. 2 209 Mg year-1 or 0.7 Mg ha-1 year-1). The main buffer in the study area is papyrus at the shore of Lake Victoria. Also sugarcane can be a major buffer. However, the sugarcane-area is intersected by com-pounds, landing sites, footpaths and main roads that generate large amounts of sediment and function as main bypass mechanisms (high CR) facilitating and enhancing sediment delivery to Lake Victoria.

A Tool for Assessing Future Capacity Loss Due to Sedimentation in the United States' Reservoirs

NASA Astrophysics Data System (ADS)

Pinson, A. O.; Baker, B.; White, K. D.

2017-12-01

Federal reservoirs are critical components of the United States' water supply, flood risk management, hydropower and navigation infrastructure. These reservoirs included capacity for storage loss due to the deposition of sediment by inflowing streams in their original design. However, the actual rate of capacity loss experienced is controlled in part by climate, topography, soils, and land use/land cover, and may vary from the design. To assess the current and future vulnerability of its reservoirs to sedimentation. USACE has developed an online planning tool to identify USACE reservoirs where sedimentation is currently a problem (e.g., sedimentation rate exceeds design sedimentation rate, or zone losses disproportionately affect authorized purposes), and reservoirs where rates are expected to increase significantly in the future. The goal is to be able to prioritize operation and maintenance actions to minimize the effects of reservoir capacity loss on authorized purposes and help maximize reservoir use life.

Use of slow-release fertilizer and biopolymers for stimulating hydrocarbon biodegradation in oil-contaminated beach sediments.

PubMed

Xu, Ran; Yong, Li Ching; Lim, Yong Giak; Obbard, Jeffrey Philip

2005-01-01

Nutrient concentration and hydrocarbon bioavailability are key factors affecting biodegradation rates of oil in contaminated beach sediments. The effect of a slow-release fertilizer, Osmocote, as well as two biopolymers, chitin and chitosan, on the bioremediation of oil-spiked beach sediments was investigated using an open irrigation system over a 56-day period under laboratory conditions. Osmocote was effective in sustaining a high level of nutrients in leached sediments, as well as elevated levels of microbial activity and rates of hydrocarbon biodegradation. Chitin was more biodegradable than chitosan and gradually released nitrogen into the sediment. The addition of chitin or chitosan to the Osmocote amended sediments enhanced biodegradation rates of the alkanes relative to the presence of Osmocote alone, where chitosan was more effective than chitin due to its greater oil sorption capacity. Furthermore, chitosan significantly enhanced the biodegradation rates of all target polycyclic aromatic hydrocarbons.

Seasonal Rates of Methane Oxidation in Anoxic Marine Sediments

PubMed Central

Iversen, Niels; Blackburn, T. Henry

1981-01-01

Methane concentrations and rates of methane oxidation were measured in intact sediment cores from an inshore marine sediment at Jutland, Denmark. The rates of methane oxidation, determined by the appearance of 14CO2 from injected 14CH4, varied with sediment depth and season. Most methane oxidation was anoxic, but oxygen may have contributed to methane oxidation at the sediment surface. Cumulative rates (0- to 12-cm depth) for methane oxidation at Kysing Fjord were 3.34, 3.48, 8.60, and 17.04 μmol m−2 day−1 for April (4°C), May (13°C), July (17°C), and August (21°C), respectively. If all of the methane was oxidized by sulfate, it would account for only 0.01 to 0.06% of the sulfate reduction. The data indicate that methane was produced, in addition to being oxidized, in the 0- to 18-cm sediment stratum. PMID:16345784

Geomorphic response of rivers to glacial retreat and increasing peak flows downstream from Mount Rainier, Washington

NASA Astrophysics Data System (ADS)

Czuba, J. A.; Barnas, C. R.; Magirl, C. S.; Voss, F. D.

2010-12-01

On Mount Rainier, Washington, the National Park Service has documented widespread aggradation of as much as 10 m since the early 20th century, of rivers draining the glaciated stratovolcano. This rapid sedimentation appears to be related to glacial retreat and also may be a function of the increased magnitude and timing of peak flows that mobilize and transport sediment. We are conducting an assessment of the Puget Lowland rivers that drain Mount Rainier, 25-100 km downstream from the park boundary, to document the geomorphic response of the downstream reaches given the widespread aggradation upstream. These downstream reaches provide critical aquatic habitat for spawning and rearing of several species of salmonids, including endangered Chinook salmon and steelhead. Fluvial sedimentation can have both deleterious and beneficial effects on aquatic habitat depending on sediment particle size, river slope and width, and river management. To date, our work shows sedimentation of as much as 2 m between 1984 and 2009 in these lowland rivers. Aggradation rates that were calculated by comparing channel change at 156 cross sections, ranged between 4.8 and 9.1 cm/yr in reaches where rivers exit the mountain front and enter the lowland. Analysis of streamflow-gaging station data from throughout the watersheds draining Mount Rainier show rapid incision and aggradation, suggesting pulses of coarse-grained bedload may be moving down the mountainous rivers as kinetic waves. Preliminary results, however, seem to indicate that the rivers in the Puget Lowland have not yet experienced significant widespread sedimentation directly related to glacial retreat. Estimating the time of arrival of mobilized alluvium is a critical need for resource managers given the potential effects of sedimentation on river flood-conveyance capacity, fish habitat, and estuarine wetlands.

Cohesive Strength of Gas-hydrate-bearing Marine Sediments

NASA Astrophysics Data System (ADS)

Cook, A. E.; Goldberg, D.

2005-12-01

We examine the relationship between gas hydrate saturation and the cohesive strength of marine sediments in a variety of continental margin settings. The cohesive strength (cohesion) is a fundamental physical property controlling sediment resistance to compressive failure. The cohesion (Co), is typically defined by the uncompressive rock strength and the friction angle, but it can also be related to the dynamic Young's modulus (ED), where: Co = 1.5*10-3 ED. The dynamic Young's modulus is computed using in situ Vp, Vs, and bulk density borehole logs. The Co profiles are compared to estimates of the in situ hydrate saturation, Sh, calculated using electrical resistivity logs and the modified Archie formula: Sh = 1 - (aRw/RΦm)1/n. We will present results of these comparisons from data collected during Ocean Drilling Program Legs at Cascadia margin (204 & 168) and Blake Ridge (164), the JIP gas hydrate drilling project in the Gulf of Mexico, and Malik permafrost wells. In general, at all the sites investigated, Co steadily increases downhole as sediments compact due to overburden. In marine sediments, cohesion ranges from 500-2000kPa above the BSR, with a baseline gradient usually between 5 and 10 kPa/m. Preliminary results show at Cascadia margin that sediments with Sh > 15%, Co increases dramatically, at least 200kPa greater than the general trend of the downhole gradient. This suggests that Co is affected directly by Sh, and may be related to the rate of change in Sh (e.g. gradual or sharp) as a function of depth. Further study on the relationship between Co and Sh may provide information on the growth habit of gas hydrates in sediment pore spaces.

Methane and Carbon Dioxide Production Rates in Lake Sediments from Sub-Arctic Sweden

NASA Astrophysics Data System (ADS)

DeStasio, J.; Halloran, M.; Erickson, L. M.; Varner, R. K.; Johnson, J. E.; Setera, J.; Prado, M. F.; Wik, M.; Crill, P. M.

2013-12-01

Ecosystems at high latitudes are undergoing rapid change due to amplified arctic warming. Lakes in these regions are sources of both methane (CH4) and carbon dioxide (CO2) to the atmosphere and will likely be impacted by elevated temperatures. Because of the potential increase in the release of organic carbon due to thawing permafrost, it is believed that methanogenesis rates within neighboring fresh water sediments will display a positive feedback response, by increasing CH4 emission to the atmosphere. We studied CH4 production potential of sediments using cores from three lakes in the Stordalen Mire complex in sub-Arctic, Sweden: Inre Harrsjön, Mellan Harrsjön, and Villasjön. Sediment cores were incubated to determine CO2 and CH4 production rates and were analyzed for CH4 concentrations, dissolved inorganic carbon (DIC) concentrations, total organic carbon (TOC) concentrations, as well as carbon, nitrogen and sulfur content. Our results from the Villasjön cores indicate that CH4 production rates were highest at the same sediment depths as peak dissolved CH4 concentrations, with maximum values between depths of approximately 10cm and 30cm. Additionally, the highest observed CH4 production rates were in sediments from areas within Villasjön known to have the highest rates of CH4 ebullition. CO2 production rates were generally highest within surface sediments ranging from about 4cm to 11cm in depth, with production rates displaying a steady decrease below 11cm. Additionally, observed CO2 production rates correlated with total organic carbon (TOC) concentrations with respect to sediment depth, but displayed no relationship with dissolved inorganic carbon (DIC). Further analysis will be conducted to determine how CH4 and CO2 production characteristics vary between sediment core samples, as well as isotopic analysis of select samples taken from each lake.

Sludge settling processes in SBR-related sewage treatment plants according to the Biocos method.

PubMed

Meusel, S; Englert, R

2004-01-01

This paper describes the investigations in a sedimentation and circulation reactor (SU-reactor) of a three-phase Biocos plant. The aim of these investigations was the determination of the temporal and depth-dependent distribution of suspended solid contents, as well as describing the sludge sedimentation curves. The calculated results reveal peculiarities of the Biocos method with regard to sedimentation processes. In the hydraulically uninterrupted (pre-)settling phase, a sludge level depth was observed, which remained constant over the reactor surface and increased linearly according to the sludge volume. The settling and the thickening processes of this phase corresponded to a large extent to the well-known settling test in a one-litre measuring cylinder. During the discharge phase, the investigated settling rate was overlaid by the surface loading rate and the sludge level changed depending on the difference between those two parameters. The solid distribution of the A-phase indicated a formation of functional zones, which were influenced by the surface loading. The formation was comparable to the formation of layers in secondary settling tanks with vertical flow. The concentration equalisation between the biological reactor and the SU-reactor proved to be problematic during the circulation phase, because a type of internal sludge circulation occurred in the SU-reactor. A permanent sludge recirculation seems to be highly recommendable.