CAMAC throughput of a new RISC-based data acquisition computer at the DIII-D tokamak

NASA Astrophysics Data System (ADS)

Vanderlaan, J. F.; Cummings, J. W.

1993-10-01

The amount of experimental data acquired per plasma discharge at DIII-D has continued to grow. The largest shot size in May 1991 was 49 Mbyte; in May 1992, 66 Mbyte; and in April 1993, 80 Mbyte. The increasing load has prompted the installation of a new Motorola 88100-based MODCOMP computer to supplement the existing core of three older MODCOMP data acquisition CPU's. New Kinetic Systems CAMAC serial highway driver hardware runs on the 88100 VME bus. The new operating system is MODCOMP REAL/IX version of AT&T System V UNIX with real-time extensions and networking capabilities; future plans call for installation of additional computers of this type for tokamak and neutral beam control functions. Experiences with the CAMAC hardware and software will be chronicled, including observation of data throughput. The Enhanced Serial Highway crate controller is advertised as twice as fast as the previous crate controller, and computer I/O speeds are expected to also increase data rates.

TRAMP; The next generation data acquisition for RTP

DOE Office of Scientific and Technical Information (OSTI.GOV)

van Haren, P.C.; Wijnoltz, F.

1992-04-01

The Rijnhuizen Tokamak Project RTP is a medium-sized tokamak experiment, which requires a very reliable data-acquisition system, due to its pulsed nature. Analyzing the limitations of an existing CAMAC-based data-acquisition system showed, that substantial increase of performance and flexibility could best be obtained by the construction of an entirely new system. This paper discusses this system, CALLED TRAMP (Transient Recorder and Amoeba Multi Processor), based on tailor-made transient recorders with a multiprocessor computer system in VME running Amoeba. The performance of TRAMP exceeds the performance of the CAMAC system by a factor of four. The plans to increase the flexibilitymore » and for a further increase of performance are presented.« less

The new Langley Research Center advanced real-time simulation (ARTS) system

NASA Technical Reports Server (NTRS)

Crawford, D. J.; Cleveland, J. I., II

1986-01-01

Based on a survey of current local area network technology with special attention paid to high bandwidth and very low transport delay requirements, NASA's Langley Research Center designed a new simulation subsystem using the computer automated measurement and control (CAMAC) network. This required significant modifications to the standard CAMAC system and development of a network switch, a clocking system, new conversion equipment, new consoles, supporting software, etc. This system is referred to as the advanced real-time simulation (ARTS) system. It is presently being built at LaRC. This paper provides a functional and physical description of the hardware and a functional description of the software. The requirements which drove the design are presented as well as present performance figures and status.

An OS9-UNIX data acquisition system with ECL readout

NASA Astrophysics Data System (ADS)

Ziem, P.; Beschorner, C.; Bohne, W.; Drescher, B.; Friese, T.; Kiehne, T.; Kluge, Ch.

1996-02-01

A new data acquisition system has been developed at the Hahn-Meitner-Institut to handle almost 550 parameters of nuclear physics experiments. The system combines a UNIX host running a portable data buffer router and a VME front-end based on the OS9 real time operating system. Different kinds of pulse analyzers are located in several CAMAC crates which are controlled by the VME system via a VICbus connection. Data readout is performed by means of an ECL daisy chain. Besides controlling CAMAC the main purpose of the VME front-end is event data formatting and histogramming. Using TCP/IP services, the UNIX host receives formatted data packages for data storage and display. During a beam time at the antiproton accelerator LEAR/CERN, the PS208 experiment has accumulated about 100 Gbyte of event data [2

An OS9-UNIX data acquisition system with ECL readout

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ziem, P.; Beschorner, C.; Bohne, W.

1996-02-01

A new data acquisition system has been developed at the Hahn-Meitner-Institut to handle almost 550 parameters of nuclear physics experiments. The system combines a UNIX host running a portable data buffer router and a VME front-end based on the OS9 real time operating system. Different kinds of pulse analyzers are located in several CAMAC crates which are controlled by the VME system via a VICbus connection. Data readout is performed by means of an ECL daisy chain. Besides controlling CAMAC the main purpose of the VME front-end is event data formatting and histogramming. Using TCP/IP services, the UNIX host receivesmore » formatted data packages for data storage and display. During a beam time at the antiproton accelerator LEAR/CERN, the PS208 experiment has accumulated about 100 Gbyte of event data.« less

SM-4 computer and CAMAC equipment in automating a ROMS-2A mass spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bulgakov, R.Sh.; Gafurov, R.A.; Safin, D.N.

1988-05-01

A data acquisition system was developed which provides for measuring mass peaks on three parameters as well as measuring working parameters. The computer memory stores 40 kHz signals, with an ADC cycle time of 10 microsec. A structural diagram is given together with upgrades made in the CAMAC apparatus to improve the speed and extend the application. Working parameters such as the pressures in pipes and the temperature in the test zone can be monitored by splitting the measurements into two cycles alternating with a controlled frequency: gas composition and technological parameter measurement.

A USB-2 based portable data acquisition system for detector development and nuclear research

NASA Astrophysics Data System (ADS)

Jiang, Hao; Ojaruega, M.; Becchetti, F. D.; Griffin, H. C.; Torres-Isea, R. O.

2011-10-01

A highly portable high-speed CAMAC data acquisition system has been developed using Kmax software (Sparrow, Inc.) for Macintosh laptop and tower computers. It uses a USB-2 interface to the CAMAC crate controller with custom-written software drivers. Kmax permits 2D parameter gating and specific algorithms have been developed to facilitate the rapid evaluation of various multi-element nuclear detectors for energy and time-of-flight measurements. This includes tests using neutrons from 252Cf and a 2.5 MeV neutron generator as well as standard gamma calibration sources such as 60Co and 137Cs. In addition, the system has been used to measure gamma-gamma coincidences over extended time periods using radioactive sources (e.g., Ra-228, Pa-233, Np-237, and Am-243).

Using a graphical programming language to write CAMAC/GPIB instrument drivers

NASA Technical Reports Server (NTRS)

Zambrana, Horacio; Johanson, William

1991-01-01

To reduce the complexities of conventional programming, graphical software was used in the development of instrumentation drivers. The graphical software provides a standard set of tools (graphical subroutines) which are sufficient to program the most sophisticated CAMAC/GPIB drivers. These tools were used and instrumentation drivers were successfully developed for operating CAMAC/GPIB hardware from two different manufacturers: LeCroy and DSP. The use of these tools is presented for programming a LeCroy A/D Waveform Analyzer.

Development of a data acquisition system using a RISC/UNIX TM workstation

NASA Astrophysics Data System (ADS)

Takeuchi, Y.; Tanimori, T.; Yasu, Y.

1993-05-01

We have developed a compact data acquisition system on RISC/UNIX workstations. A SUN TM SPARCstation TM IPC was used, in which an extension bus "SBus TM" was linked to a VMEbus. The transfer rate achieved was better than 7 Mbyte/s between the VMEbus and the SUN. A device driver for CAMAC was developed in order to realize an interruptive feature in UNIX. In addition, list processing has been incorporated in order to keep the high priority of the data handling process in UNIX. The successful developments of both device driver and list processing have made it possible to realize the good real-time feature on the RISC/UNIX system. Based on this architecture, a portable and versatile data taking system has been developed, which consists of a graphical user interface, I/O handler, user analysis process, process manager and a CAMAC device driver.

A system for the automated data-acquisition of fast transient signals in excitable membranes.

PubMed

Bustamante, J O

1988-01-01

This paper provides a description of a system for the acquisition of fast transient currents flowing across excitable membranes. The front end of the system consists of a CAMAC crate with plug-in modules. The modules provide control of CAMAC operations, analog to digital conversion, electronic memory storage and timing of events. The signals are transferred under direct memory access to an IBM PC microcomputer through a special-purpose interface. Voltage levels from a digital to analog board in the microcomputer are passed through multiplexers to produce the desired voltage pulse patterns to elicit the transmembrane currents. The dead time between consecutive excitatory voltage pulses is limited only by the computer data bus and the software characteristics. The dead time between data transfers can be reduced to the order of milliseconds, which is sufficient for most experiments with transmembrane ionic currents.

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. E. Lawson, R. Marsala, S. Ramakrishnan, X. Zhao, P. Sichta

In order to provide improved and expanded experimental capabilities, the existing Transrex power supplies at PPPL are to be upgraded and modernized. Each of the 39 power supplies consists of two six pulse silicon controlled rectifier sections forming a twelve pulse power supply. The first modification is to split each supply into two independent six pulse supplies by replacing the existing obsolete twelve pulse firing generator with two commercially available six pulse firing generators. The second change replaces the existing control link with a faster system, with greater capacity, which will allow for independent control of all 78 power supplymore » sections. The third change replaces the existing Computer Automated Measurement and Control (CAMAC) based fault detector with an Experimental Physics and Industrial Control System (EPICS) compatible unit, eliminating the obsolete CAMAC modules. Finally the remaining relay logic and interfaces to the "Hardwired Control System" will be replaces with a Programmable Logic Controller (PLC).« less

A CAMAC display module for fast bit-mapped graphics

NASA Astrophysics Data System (ADS)

Abdel-Aal, R. E.

1992-10-01

In many data acquisition and analysis facilities for nuclear physics research, utilities for the display of two-dimensional (2D) images and spectra on graphics terminals suffer from low speed, poor resolution, and limited accuracy. Development of CAMAC bit-mapped graphics modules for this purpose has been discouraged in the past by the large device count needed and the long times required to load the image data from the host computer into the CAMAC hardware; particularly since many such facilities have been designed to support fast DMA block transfers only for data acquisition into the host. This paper describes the design and implementation of a prototype CAMAC graphics display module with a resolution of 256×256 pixels at eight colours for which all components can be easily accommodated in a single-width package. Employed is a hardware technique which reduces the number of programmed CAMAC data transfer operations needed for writing 2D images into the display memory by approximately an order of magnitude, with attendant improvements in the display speed and CPU time consumption. Hardware and software details are given together with sample results. Information on the performance of the module in a typical VAX/MBD data acquisition environment is presented, including data on the mutual effects of simultaneous data acquisition traffic. Suggestions are made for further improvements in performance.

QMODULE: CAMAC modules recognized by the QAL compiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kellogg, M.; Minor, M.M.; Shlaer, S.

1977-10-01

The compiler for the Q Analyzer Language, QAL, recognizes a certain set of CAMAC modules as having known characteristics. The conventions and procedures used to describe these modules are discussed as well as the tools available to the user for extending this set as required.

Multinode data acquisition and control system for the 4-element TACTIC telescope array

NASA Astrophysics Data System (ADS)

Yadav, K. K.; Chouhan, N.; Kaul, S. R.; Koul, R.

2002-03-01

An interrupt driven multinode data acquisition and control system has been developed for the 4-element gamma-ray telescope array, TACTIC. Computer networking technology and the CAMAC bus have been integrated to develop this icon-based, userfriendly failsafe system. The paper describes the salient features of the system.

A distributed control system for the lower-hybrid current drive system on the Tokamak de Varennes

NASA Astrophysics Data System (ADS)

Bagdoo, J.; Guay, J. M.; Chaudron, G.-A.; Decoste, R.; Demers, Y.; Hubbard, A.

1990-08-01

An rf current drive system with an output power of 1 MW at 3.7 GHz is under development for the Tokamak de Varennes. The control system is based on an Ethernet local-area network of programmable logic controllers as front end, personal computers as consoles, and CAMAC-based DSP processors. The DSP processors ensure the PID control of the phase and rf power of each klystron, and the fast protection of high-power rf hardware, all within a 40 μs loop. Slower control and protection, event sequencing and the run-time database are provided by the programmable logic controllers, which communicate, via the LAN, with the consoles. The latter run a commercial process-control console software. The LAN protocol respects the first four layers of the ISO/OSI 802.3 standard. Synchronization with the tokamak control system is provided by commercially available CAMAC timing modules which trigger shot-related events and reference waveform generators. A detailed description of each subsystem and a performance evaluation of the system will be presented.

A programmable ISA to USB interface

NASA Astrophysics Data System (ADS)

Ribas, R. V.

2013-05-01

A programmable device to access and control ISA-standard camac instrumentation and interfacing it to the USB port of computers, is described in this article. With local processing capabilities and event buffering before sending data to the computer, the new acquisition system become much more efficient.

A status report of a FASTBUS at KEK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arai, Y.; Endo, I.; Inoue

1983-02-01

Some FASTBUS modules have been produced and successfully tested at KEK. The test system consisted of a single backplane segment equipped with ancillary logic, two masters driven by the MC68000 microprocessor and two slaves which have several read/write registers. A simple FASTBUS-CAMAC interface is also described.

DIII-D Neutron Measurement: Status and Plan for Simplification and Upgrade

NASA Astrophysics Data System (ADS)

Zhu, Y. B.; Heidbrink, W. W.; Taylor, P. L.; Finkenthal, D.

2017-10-01

Neutron diagnostics play key essential roles on DIII-D. Historically an 18-channel 2.45MeV D-D neutron measurement system based on 3He and BF3 proportional counters was inherited from Doublet-III including associated electronics and CAMAC data acquisition. Three fission chambers and two neutron scintillators were added in the 1980s and middle 1990s respectively. For Tritium burn-up studies, two 14MeV D-T neutron measurement systems were installed in 2009 and 2010. Operation and maintenance experience have led to a plan to simplify and upgrade these aging systems to provide a more economical and reliable solution for future DIII-D experiments. On simplification, most conventional expensive NIM and CAMAC modules will be removed. Advanced technologies like ultra-fast data acquisition and software-based pulse identification have been successfully tested. Significant data reduction and efficiency improvement will be achieved by real-time digital pulse identification with a field-programmable gate array. The partly renewed system will consist of 4 neutron counters for absolute calibration and 4 relatively calibrated neutron scintillators covering a wide measurement range. Work supported by US DOE under DE-FC02-04ER54698.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kouzes, R.T.; Piilonen, L.; Schreiber, D.

Apple microcomputers have been combined with CAMAC to produce data acquisition systems used for a variety of applications at the Princeton Cyclotron Laboratory. Two specific implementations are discussed: a general one or two parameter MCA system and a specific eleven parameter system. A multiplicity of off-line experiments led to the need for these systems having data manipulation and control ability beyond that of low cost systems available commercially. A serial communications port allows for data transfer to the main computer for more complete analysis.

The hybrid UNIX controller for real-time data acquisition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huesman, R.H.; Klein, G.J.; Fleming, T.K.

1996-06-01

The authors describe a hybrid data acquisition architecture integrating a conventional UNIX workstation with CAMAC-based real-time hardware. The system combines the high-level programming simplicity and user interface of a UNIX workstation with the low-level timing control available from conventional real-time hardware. They detail this architecture as it has been implemented for control of the Donner 600-Crystal Positron Tomograph (PET600). Low-level data acquisition is carried out in this system using eight LeCroy 3588 histogrammers, which together after derandomization, acquire events at rates up to 4 MHz, and two dedicated Motorola 6809 microprocessors, which arbitrate fine timing control during acquisition. A SUNmore » Microsystems UNIX workstation is used for high-level control, allowing an easily extensible user interface in an X-Windows environment, as well as real-time communications to the low-level acquisition units. Communication between the high- and low-level units is carried out via a Jorway 73A SCSI-CAMAC crate controller and a serial interface. For this application, the hybrid configuration segments low from high-level control for ease of maintenance and provided a low-cost upgrade from dated high-level control hardware.« less

A UNIX-based real-time data acquisition system for microprobe analysis using an advanced X11 window toolkit

NASA Astrophysics Data System (ADS)

Kramer, J. L. A. M.; Ullings, A. H.; Vis, R. D.

1993-05-01

A real-time data acquisition system for microprobe analysis has been developed at the Free University of Amsterdam. The system is composed of two parts: a front-end real-time and a back-end monitoring system. The front-end consists of a VMEbus based system which reads out a CAMAC crate. The back-end is implemented on a Sun work station running the UNIX operating system. This separation allows the integration of a minimal, and consequently very fast, real-time executive within the sophisticated possibilities of advanced UNIX work stations.

Feasibility study of the design of Bi Ra Systems, Incorporated model 5301, 5101, and 3222 CAMAC modules for space use

NASA Technical Reports Server (NTRS)

Biswell, L.; Mcelderry, R.

1976-01-01

Cost estimates are determined for redesigned modules. Consideration is given to incorporation of NASA approved components, component screening and documentation, as well as reduced power consumption. Results show that r designed modules will function reliably in a space environment of 50 C and withstand greater than 15 G's of random vibration between 40 Hz and 400 Hz.

A memory module for experimental data handling

NASA Astrophysics Data System (ADS)

De Blois, J.

1985-02-01

A compact CAMAC memory module for experimental data handling was developed to eliminate the need of direct memory access in computer controlled measurements. When using autonomous controllers it also makes measurements more independent of the program and enlarges the available space for programs in the memory of the micro-computer. The memory module has three modes of operation: an increment-, a list- and a fifo mode. This is achieved by connecting the main parts, being: the memory (MEM), the fifo buffer (FIFO), the address buffer (BUF), two counters (AUX and ADDR) and a readout register (ROR), by an internal 24-bit databus. The time needed for databus operations is 1 μs, for measuring cycles as well as for CAMAC cycles. The FIFO provides temporary data storage during CAMAC cycles and separates the memory part from the application part. The memory is variable from 1 to 64K (24 bits) by using different types of memory chips. The application part, which forms 1/3 of the module, will be specially designed for each application and is added to the memory chian internal connector. The memory unit will be used in Mössbauer experiments and in thermal neutron scattering experiments.

VMEbus based computer and real-time UNIX as infrastructure of DAQ

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yasu, Y.; Fujii, H.; Nomachi, M.

1994-12-31

This paper describes what the authors have constructed as the infrastructure of data acquisition system (DAQ). The paper reports recent developments concerned with HP VME board computer with LynxOS (HP742rt/HP-RT) and Alpha/OSF1 with VMEbus adapter. The paper also reports current status of developing a Benchmark Suite for Data Acquisition (DAQBENCH) for measuring not only the performance of VME/CAMAC access but also that of the context switching, the inter-process communications and so on, for various computers including Workstation-based systems and VME board computers.

Trigger and data acquisition system for the N- N experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldo-Ceolin, M.; Bobisut, F.; Bonaiti, V.

1991-04-01

In this paper the Trigger and Data Acquisition system of the N-{bar N} experiment at the Institute Laue-Langevin at Grenoble is presented, together with CAMAC modules especially designed for this experiment. The trigger system is organized on three logical levels; it works in the presence of a high level of beam induced noise, without beam pulse synchronization, looking for a very rare signal. The data acquisition is based on a MicroVax II computer, in a cluster with 4 VaxStations, the DAQP software developed at CERN. The system has been working for a year with high efficiency and reliability.

A multi-channel coronal spectrophotometer.

NASA Technical Reports Server (NTRS)

Landman, D. A.; Orrall, F. Q.; Zane, R.

1973-01-01

We describe a new multi-channel coronal spectrophotometer system, presently being installed at Mees Solar Observatory, Mount Haleakala, Maui. The apparatus is designed to record and interpret intensities from many sections of the visible and near-visible spectral regions simultaneously, with relatively high spatial and temporal resolution. The detector, a thermoelectrically cooled silicon vidicon camera tube, has its central target area divided into a rectangular array of about 100,000 pixels and is read out in a slow-scan (about 2 sec/frame) mode. Instrument functioning is entirely under PDP 11/45 computer control, and interfacing is via the CAMAC system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, S.H.; Oxoby, G.J.; Trang, Q.H.

The advent of the personal microcomputer provides a new tool for the debugging, calibration and monitoring of small scale physics apparatus; e.g., a single detector being developed for a larger physics apparatus. With an appropriate interface these microcomputer systems provide a low cost (1/3 the cost of a comparable minicomputer system), convenient, dedicated, portable system which can be used in a fashion similar to that of portable oscilloscopes. Here we describe an interface between the Apple computer and CAMAC which is now being used to study the detector for a Cerenkov ring-imaging device. The Apple is particularly well-suited to thismore » application because of its ease of use, hi-resolution graphics peripheral buss and documentation support.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxoby, G.J.; Trang, Q.H.; Williams, S.H.

The advent of the personal microcomputer provides a new tool for the debugging, calibration and monitoring of small scale physics apparatus, e.g., a single detector being developed for a larger physics apparatus. With an appropriate interface these microcomputer systems provide a low cost (1/3 the cost of a comparable minicomputer system), convenient, dedicated, portable system which can be used in a fashion similar to that of portable oscilloscopes. Here, an interface between the Apple computer and CAMAC which is now being used to study the detector for a Cerenkov ring-imaging device is described. The Apple is particularly well-suited to thismore » application because of its ease of use, hi-resolution graphics, peripheral bus and documentation support.« less

"Data Acquisition Systems"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unterweger, Michael; Costrell, Louis deceased

2009-07-07

This project involved support for Lou Costrell and myself in the development of IEEE and IEC standards for nuclear counting and data acquisition systems. Over the years, as a result of this support, Lou and I were able to attend standards meetings of IEEE and IEC, which led directly to the publication of many standards for NIM systems, FastBus and CAMAC. We also chaired several writing committees as well as ANSI N42 (Nuclear instrumentation), IEEE NIM (NIM standard), IEEE NID (NPSS nuclear instruments and detector) and IEC TC45 WG9 (Nuclear instrumentation). Through this support we were able to assure thatmore » the interests of the US and DOE were expressed and implemented in the various standards.« less

CAMAC driver for the RSX-11M V3 operating system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tippie, J. W.; Cannon, P. H.

1977-01-01

A driver for Kinetic Systems 3911A dedicated crate controller and 3992 serial highway driver for RSX-11M is described. The implementation includes a modified UCB structure. With this structure, multiple active I/O requests are supported to a single controller. The completion of an I/O request may be tied to external events via a WAIT-FOR-LAM command. Features of the driver include the ability to pass a list of FNA's in a single QIO call, serial highway overhead transparent at the QIO level, and special control commands to the driver passed in the FNA list. 1 figure.

Fermilab`s DART DA system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pordes, R.; Anderson, J.; Berg, D.

1994-04-01

DART is the new data acquisition system designed and implemented for six Fermilab experiments by the Fermilab Computing Division and the experiments themselves. The complexity of the experiments varies greatly. Their data taking throughput and event filtering requirements range from a few (2-5) to tens (80) of CAMAC, FASTBUS and home built front end crates; from a few 100 KByte/sec to 160 MByte/sec front end data collection rates; and from 0-3000 Mips of level 3 processing. The authors report on the architecture and implementation of DART to this date, and the hardware and software components that are being developed andmore » supported.« less

Fermilab`s DART DA system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pordes, R.; Anderson, J.; Berg, D.

1994-12-31

DART is the new data acquisition system designed and implemented for six Fermilab experiments by the Fermilab Computing Division and the experiments themselves. The complexity of the experiments varies greatly. Their data taking throughput and event filtering requirements range from a few (2-5) to tens (80) of CAMAC, FASTBUS and home built front end crates; from a few 100 KByte/sec to 160 MByte/sec front end data collection rates; and from 0-3000 Mips of level 3 processing. The authors report on the architecture and implementation of DART to this data, and the hardware and software components that are being developed andmore » supported.« less

A new array for the study of ultra high energy gamma-ray sources

NASA Technical Reports Server (NTRS)

Brooke, G.; Lambert, A.; Ogden, P. A.; Patel, M.; Ferrett, J. C.; Reid, R. J. O.; Watson, A. A.; West, A. A.

1985-01-01

The design and operation of a 32 x 1 10 to the 15th power sq m array of scintillation detectors for the detection of 10 to the 15th power eV cosmic rays is described with an expected angular resolution of 1 deg, thus improving the present signal/background ratio for gamma ray sources. Data are recorded on a hybrid CAMAC, an in-house system which uses a laser and Pockel-Cell arrangement to routinely calibrate the timing stability of the detectors.

Data acquisition and processing system for the HT-6M tokamak fusion experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shu, Y.T.; Liu, G.C.; Pang, J.Q.

1987-08-01

This paper describes a high-speed data acquisition and processing system which has been successfully operated on the HT-6M tokamak fusion experimental device. The system collects, archives and analyzes up to 512 kilobytes of data from each shot of the experiment. A shot lasts 50-150 milliseconds and occurs every 5-10 minutes. The system consists of two PDP-11/24 computer systems. One PDP-11/24 is used for real-time data taking and on-line data analysis. It is based upon five CAMAC crates organized into a parallel branch. Another PDP-11/24 is used for off-line data processing. Both data acquisition software RSX-DAS and data processing software RSX-DAPmore » have modular, multi-tasking and concurrent processing features.« less

A Compton suppressed detector multiplicity trigger based digital DAQ for gamma-ray spectroscopy

NASA Astrophysics Data System (ADS)

Das, S.; Samanta, S.; Banik, R.; Bhattacharjee, R.; Basu, K.; Raut, R.; Ghugre, S. S.; Sinha, A. K.; Bhattacharya, S.; Imran, S.; Mukherjee, G.; Bhattacharyya, S.; Goswami, A.; Palit, R.; Tan, H.

2018-06-01

The development of a digitizer based pulse processing and data acquisition system for γ-ray spectroscopy with large detector arrays is presented. The system is based on 250 MHz 12-bit digitizers, and is triggered by a user chosen multiplicity of Compton suppressed detectors. The logic for trigger generation is similar to the one practised for analog (NIM/CAMAC) pulse processing electronics, while retaining the fast processing merits of the digitizer system. Codes for reduction of data acquired from the system have also been developed. The system has been tested with offline studies using radioactive sources as well as in the in-beam experiments with an array of Compton suppressed Clover detectors. The results obtained therefrom validate its use in spectroscopic efforts for nuclear structure investigations.

Digital Low Level RF Systems for Fermilab Main Ring and Tevatron

NASA Astrophysics Data System (ADS)

Chase, B.; Barnes, B.; Meisner, K.

1997-05-01

At Fermilab, a new Low Level RF system is successfully installed and operating in the Main Ring. Installation is proceeding for a Tevatron system. This upgrade replaces aging CAMAC/NIM components for an increase in accuracy, reliability, and flexibility. These VXI systems are based on a custom three channel direct digital synthesizer(DDS) module. Each synthesizer channel is capable of independent or ganged operation for both frequency and phase modulation. New frequency and phase values are computed at a 100kHz rate on the module's Analog Devices ADSP21062 (SHARC) digital signal processor. The DSP concurrently handles feedforward, feedback, and beam manipulations. Higher level state machines and the control system interface are handled at the crate level using the VxWorks operating system. This paper discusses the hardware, software and operational aspects of these LLRF systems.

A balloon-borne high-resolution spectrometer for observations of gamma-ray emission from solar flares

NASA Technical Reports Server (NTRS)

Crannell, C. J.; Starr, R.; Stottlemyre, A. R.; Trombka, J. I.

1984-01-01

The design, development, and balloon-flight verification of a payload for observations of gamma-ray emission from solar flares are reported. The payload incorporates a high-purity germanium semiconductor detector, standard NIM and CAMAC electronics modules, a thermally stabilized pressure housing, and regulated battery power supplies. The flight system is supported on the ground with interactive data-handling equipment comprised of similar electronics hardware. The modularity and flexibility of the payload, together with the resolution and stability obtained throughout a 30-hour flight, make it readily adaptable for high-sensitivity, long-duration balloon fight applications.

Data acquisition using the 168/E. [CERN ISR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carroll, J.T.; Cittolin, S.; Demoulin, M.

1983-03-01

Event sizes and data rates at the CERN anti p p collider compose a formidable environment for a high level trigger. A system using three 168/E processors for experiment UA1 real-time event selection is described. With 168/E data memory expanded to 512K bytes, each processor holds a complete event allowing a FORTRAN trigger algorithm access to data from the entire detector. A smart CAMAC interface reads five Remus branches in parallel transferring one word to the target processor every 0.5 ..mu..s. The NORD host computer can simultaneously read an accepted event from another processor.

A modular multiple use system for precise time and frequency measurement and distribution

NASA Technical Reports Server (NTRS)

Reinhardt, V. S.; Adams, W. S.; Lee, G. M.; Bush, R. L.

1978-01-01

A modular CAMAC based system is described which was developed to meet a variety of precise time and frequency measurement and distribution needs. The system was based on a generalization of the dual mixer concept. By using a 16 channel 100 ns event clock, the system can intercompare the phase of 16 frequency standards with subpicosecond resolution. The system has a noise floor of 26 fs and a long term stability on the order of 1 ps or better. The system also used a digitally controlled crystal oscillator in a control loop to provide an offsettable 5 MHz output with subpicosecond phase tracking capability. A detailed description of the system is given including theory of operation and performance. A method to improve the performance of the dual mixer technique is discussed when phase balancing of the two input ports cannot be accomplished.

Digitally controlled twelve-pulse firing generator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berde, D.; Ferrara, A.A.

1981-01-01

Control System Studies for the Tokamak Fusion Test Reactor (TFTR) indicate that accurate thyristor firing in the AC-to-DC conversion system is required in order to achieve good regulation of the various field currents. Rapid update and exact firing angle control are required to avoid instabilities, large eddy currents, or parasitic oscillations. The Prototype Firing Generator was designed to satisfy these requirements. To achieve the required /plus or minus/0.77/degree/firing accuracy, a three-phase-locked loop reference was designed; otherwise, the Firing Generator employs digital circuitry. The unit, housed in a standard CAMAC crate, operates under microcomputer control. Functions are performed under program control,more » which resides in nonvolatile read-only memory. Communication with CICADA control system is provided via an 11-bit parallel interface.« less

A real-time data-acquisition and analysis system with distributed UNIX workstations

NASA Astrophysics Data System (ADS)

Yamashita, H.; Miyamoto, K.; Maruyama, K.; Hirosawa, H.; Nakayoshi, K.; Emura, T.; Sumi, Y.

1996-02-01

A compact data-acquisition system using three RISC/UNIX™ workstations (SUN™/SPARCstation™) with real-time capabilities of monitoring and analysis has been developed for the study of photonuclear reactions with the large-acceptance spectrometer TAGX. One workstation acquires data from memory modules in the front-end electronics (CAMAC and TKO) with a maximum speed of 300 Kbytes/s, where data size times instantaneous rate is 1 Kbyte × 300 Hz. Another workstation, which has real-time capability for run monitoring, gets the data with a buffer manager called NOVA. The third workstation analyzes the data and reconstructs the event. In addition to a general hardware and software description, priority settings and run control by shell scripts are described. This system has recently been used successfully in a two month long experiment.

Advanced Water Vapor Lidar Detection System

NASA Technical Reports Server (NTRS)

Elsayed-Ali, Hani

1998-01-01

In the present water vapor lidar system, the detected signal is sent over long cables to a waveform digitizer in a CAMAC crate. This has the disadvantage of transmitting analog signals for a relatively long distance, which is subjected to pickup noise, leading to a decrease in the signal to noise ratio. Generally, errors in the measurement of water vapor with the DIAL method arise from both random and systematic sources. Systematic errors in DIAL measurements are caused by both atmospheric and instrumentation effects. The selection of the on-line alexandrite laser with a narrow linewidth, suitable intensity and high spectral purity, and its operation at the center of the water vapor lines, ensures minimum influence in the DIAL measurement that are caused by the laser spectral distribution and avoid system overloads. Random errors are caused by noise in the detected signal. Variability of the photon statistics in the lidar return signal, noise resulting from detector dark current, and noise in the background signal are the main sources of random error. This type of error can be minimized by maximizing the signal to noise ratio. The increase in the signal to noise ratio can be achieved by several ways. One way is to increase the laser pulse energy, by increasing its amplitude or the pulse repetition rate. Another way, is to use a detector system with higher quantum efficiency and lower noise, on the other hand, the selection of a narrow band optical filter that rejects most of the day background light and retains high optical efficiency is an important issue. Following acquisition of the lidar data, we minimize random errors in the DIAL measurement by averaging the data, but this will result in the reduction of the vertical and horizontal resolutions. Thus, a trade off is necessary to achieve a balance between the spatial resolution and the measurement precision. Therefore, the main goal of this research effort is to increase the signal to noise ratio by a factor of 10 over the current system, using a newly evaluated, very low noise avalanche photo diode detector and constructing a 10 MHz waveform digitizer which will replace the current CAMAC system.

Completion of the LANSCE Proton Storage Ring Control System Upgrade -- A Successful Integration of EPICS Into a Running Control System

NASA Astrophysics Data System (ADS)

Schaller, S. C.; Bjorklund, E. A.; Carr, G. P.; Faucett, J. A.; Oothoudt, M. A.

1997-05-01

The Los Alamos Neutron Scattering Center (LANSCE) Proton Storage Ring (PSR) control system upgrade was completed in 1996. In previous work, much of a PDP-11-based control system was replaced with Experimental Physics and Industrial Control System (EPICS) controls. Several parts of the old control system which used a VAX for operator displays and direct access to a CAMAC serial highway still remained. The old system was preserved as a "fallback" if the new EPICS-based system had problems. The control system upgrade completion included conversion of several application programs to EPICS-based operator interfaces, moving some data acquisition hardware to EPICS Input-Output Controllers (IOCs), and the implementation of new gateway software to complete the overall control system interoperability. Many operator interface (OPI) screens, written by LANSCE operators, have been incorporated in the new system. The old PSR control system hardware was removed. The robustness and reliability of the new controls obviated the need for a fallback capability.

MECDAS: A distributed data acquisition system for experiments at MAMI

NASA Astrophysics Data System (ADS)

Krygier, K. W.; Merle, K.

1994-02-01

For the coincidence experiments with the three spectrometer setup at MAMI an experiment control and data acquisition system has been built and was put successfully into final operation in 1992. MECDAS is designed as a distributed system using communication via Ethernet and optical links. As the front end, VME bus systems are used for real time purposes and direct hardware access via CAMAC, Fastbus or VMEbus. RISC workstations running UNIX are used for monitoring, data archiving and online and offline analysis of the experiment. MECDAS consists of several fixed programs and libraries, but large parts of readout and analysis can be configured by the user. Experiment specific configuration files are used to generate efficient and powerful code well adapted to special problems without additional programming. The experiment description is added to the raw collection of partially analyzed data to get self-descriptive data files.

Evaluation of a commercial system for CAMAC-based control of the Chalk River Laboratories tandem-accelerator-superconducting-cyclotron complexcomplex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greiner, B.F.; Caswell, D.J.; Slater, W.R.

1992-04-01

This paper discusses the control system of the Tandem Accelerator Superconducting Cyclotron (TASCC) of AECL Research at its Chalk River Laboratories which is presently based on a PDP-11 computer and the IAS operating system. The estimated expense of a custom conversion of the system to a current, equivalent operating system is prohibitive. The authors have evaluated a commercial control package from VISTA Control Systems based on VAX microcomputers and the VMS operating system. Vsystem offers a modern, graphical operator interface, an extensive software toolkit for configuration of the system and a multi-feature data-logging capability, all of which far surpass themore » functionality of the present control system. However, the implementation of some familiar, practical features that TASCC operators find to be essential has proven to be challenging. The assessment of Vsystem, which is described in terms of presently perceived strengths and weaknesses, is, on balance, very positive.« less

Characterization of a 16-Bit Digitizer for Lidar Data Acquisition

NASA Technical Reports Server (NTRS)

Williamson, Cynthia K.; DeYoung, Russell J.

2000-01-01

A 6-MHz 16-bit waveform digitizer was evaluated for use in atmospheric differential absorption lidar (DIAL) measurements of ozone. The digitizer noise characteristics were evaluated, and actual ozone DIAL atmospheric returns were digitized. This digitizer could replace computer-automated measurement and control (CAMAC)-based commercial digitizers and improve voltage accuracy.

Computer optimization techniques for NASA Langley's CSI evolutionary model's real-time control system

NASA Technical Reports Server (NTRS)

Elliott, Kenny B.; Ugoletti, Roberto; Sulla, Jeff

1992-01-01

The evolution and optimization of a real-time digital control system is presented. The control system is part of a testbed used to perform focused technology research on the interactions of spacecraft platform and instrument controllers with the flexible-body dynamics of the platform and platform appendages. The control system consists of Computer Automated Measurement and Control (CAMAC) standard data acquisition equipment interfaced to a workstation computer. The goal of this work is to optimize the control system's performance to support controls research using controllers with up to 50 states and frame rates above 200 Hz. The original system could support a 16-state controller operating at a rate of 150 Hz. By using simple yet effective software improvements, Input/Output (I/O) latencies and contention problems are reduced or eliminated in the control system. The final configuration can support a 16-state controller operating at 475 Hz. Effectively the control system's performance was increased by a factor of 3.

SYRMEP front-end and read-out electronics

NASA Astrophysics Data System (ADS)

Arfelli, F.; Bonvicini, V.; Bravin, A.; Cantatore, G.; Castelli, E.; Cristaudo, P.; Di Michiel, M.; Longo, R.; Olivo, A.; Pani, S.; Pontoni, D.; Poropat, P.; Prest, M.; Rashevsky, A.; Tomasini, F.; Tromba, G.; Vacchi, A.; Vallazza, E.

1998-02-01

The SYRMEP approach to digital mammography implies the use of a monochromatic X-ray beam from a synchrotron source and a slot of superimposed silicon microstrip detectors as a scanning image receptor. The microstrips are read by 32-channel chips mounted on 7-layer hybrid circuits which receive control signals and operating voltages from a MASTER-SLAVE configuration of cards. The MASTER card is driven by the CIRM, a dedicated CAMAC module whose timing function can be easily excluded to obtain data-storage-only units connected to different MASTERs: this second-level modular expansion capability fully achieves the tasks of an electronics system able to follow the SYRMEP detector growth till the final size of seven thousands of channels.

Nuclear Science Symposium, 21st, Scintillation and Semiconductor Counter Symposium, 14th, and Nuclear Power Systems Symposium, 6th, Washington, D.C., December 11-13, 1974, Proceedings

NASA Technical Reports Server (NTRS)

1975-01-01

Papers are presented dealing with latest advances in the design of scintillation counters, semiconductor radiation detectors, gas and position sensitive radiation detectors, and the application of these detectors in biomedicine, satellite instrumentation, and environmental and reactor instrumentation. Some of the topics covered include entopistic scintillators, neutron spectrometry by diamond detector for nuclear radiation, the spherical drift chamber for X-ray imaging applications, CdTe detectors in radioimmunoassay analysis, CAMAC and NIM systems in the space program, a closed loop threshold calibrator for pulse height discriminators, an oriented graphite X-ray diffraction telescope, design of a continuous digital-output environmental radon monitor, and the optimization of nanosecond fission ion chambers for reactor physics. Individual items are announced in this issue.

Apparatus for controlling the scan width of a scanning laser beam

DOEpatents

Johnson, Gary W.

1996-01-01

Swept-wavelength lasers are often used in absorption spectroscopy applications. In experiments where high accuracy is required, it is desirable to continuously monitor and control the range of wavelengths scanned (the scan width). A system has been demonstrated whereby the scan width of a swept ring-dye laser, or semiconductor diode laser, can be measured and controlled in real-time with a resolution better than 0.1%. Scan linearity, or conformity to a nonlinear scan waveform, can be measured and controlled. The system of the invention consists of a Fabry-Perot interferometer, three CAMAC interface modules, and a microcomputer running a simple analysis and proportional-integral control algorithm. With additional modules, multiple lasers can be simultaneously controlled. The invention also includes an embodiment implemented on an ordinary PC with a multifunction plug-in board.

Apparatus for controlling the scan width of a scanning laser beam

DOEpatents

Johnson, G.W.

1996-10-22

Swept-wavelength lasers are often used in absorption spectroscopy applications. In experiments where high accuracy is required, it is desirable to continuously monitor and control the range of wavelengths scanned (the scan width). A system has been demonstrated whereby the scan width of a swept ring-dye laser, or semiconductor diode laser, can be measured and controlled in real-time with a resolution better than 0.1%. Scan linearity, or conformity to a nonlinear scan waveform, can be measured and controlled. The system of the invention consists of a Fabry-Perot interferometer, three CAMAC interface modules, and a microcomputer running a simple analysis and proportional-integral control algorithm. With additional modules, multiple lasers can be simultaneously controlled. The invention also includes an embodiment implemented on an ordinary PC with a multifunction plug-in board. 8 figs.

The TOFp/pVPD time-of-flight system for STAR

NASA Astrophysics Data System (ADS)

Llope, W. J.; Geurts, F.; Mitchell, J. W.; Liu, Z.; Adams, N.; Eppley, G.; Keane, D.; Li, J.; Liu, F.; Liu, L.; Mutchler, G. S.; Nussbaum, T.; Bonner, B.; Sappenfield, P.; Zhang, B.; Zhang, W.-M.

2004-04-01

A time-of-flight system was constructed for the STAR Experiment for the direct identification of hadrons produced in 197Au+ 197Au collisions at RHIC. The system consists of two separate detector subsystems, one called the Pseudo Vertex Position Detector (pVPD, the "start" detector) and the other called the Time of Flight Patch (TOFp, the "stop" detector). Each detector is based on conventional scintillator/phototube technology and includes custom high-performance front-end electronics and a common CAMAC-based digitization and read-out. The design of the system and its performance during the 2001 RHIC run will be described. The start resolution attained by the pVPD was 24 ps, implying a pVPD single-detector resolution of 58 ps. The total time resolution of the system averaged over all detector channels was 87 ps, allowing direct π/ K/ p discrimination for momenta up to ˜1.8 GeV/ c, and direct ( π+ K)/ p discrimination up to ˜3 GeV/ c.

A Plasma Diagnostic Set for the Study of a Variable Specific Impulse Magnetoplasma Rocket

NASA Astrophysics Data System (ADS)

Squire, J. P.; Chang-Diaz, F. R.; Bengtson Bussell, R., Jr.; Jacobson, V. T.; Wootton, A. J.; Bering, E. A.; Jack, T.; Rabeau, A.

1997-11-01

The Advanced Space Propulsion Laboratory (ASPL) is developing a Variable Specific Impulse Magnetoplasma Rocket (VASIMR) using an RF heated magnetic mirror operated asymmetrically. We will describe the initial set of plasma diagnostics and data acquisition system being developed and installed on the VASIMR experiment. A U.T. Austin team is installing two fast reciprocating probes: a quadruple Langmuir and a Mach probe. These measure electron density and temperature profiles, electrostatic plasma fluctuations, and plasma flow profiles. The University of Houston is developing an array of 20 highly directional Retarding Potential Analyzers (RPA) for measuring ion energy distribution function profiles in the rocket plume, giving a measurement of total thrust. We have also developed a CAMAC based data acquisition system using LabView running on a Power Macintosh communicating through a 2 MB/s serial highway. We will present data from initial plasma operations and discuss future diagnostic development.

’Do-It-Yourself’ Fallout/Blast Shelter Evaluation

DTIC Science & Technology

1984-03-01

N4AME & AOORIESS(I! dittvrevI !M’", Controlling Olif~t) IS. SEC’.JRITY CL-ASS. (GO this report) Lawrence Livermore National Laboratory Unclassified P...the data from the transient recorder iemory tirough the Computer Automated Measurement and Control (CAMAC) data busa und stores them on an $-inch...Command and Control Technical Center Emergency Technology Division Department of Defense 0a& Ridge Natioual Laboratory The Pentagon Attn: Librarian

User`s manual for the CDC-1 digitizer controller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferron, J.R.

1994-09-01

A detailed description of how to use the CDC-1 digitizer controller is given. The CDC-1 is used with the CAMAC format digitizer models in the TRAQ series (manufactured by DSP Technology Inc.), the DAD-1 data acquisition daughter board, and the Intel i860-based SuperCard-2 (manufactured, by CSP Inc.) to form a high speed data acquisition and real time analysis system. Data can be transferred to the memory on the SuperCard-2 at a rate as high as 40 million 14-bit samples per second. Depending on the model of TRAQ digitizer in use, digitizing rates up to 3.33 MHz are supported (with eightmore » data channels), or, for instance, at a sample rate of 100 kHz, 384 data channels can be acquired.« less

SPORT-SPEAR Mark III Electronics (Engineering Materials)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Drawing List DL 135-678-00-RO and the drawings listed thereon provide the specifications for construction of the SPORT-SPEAR Mark III Electronics. SPORT stands for Smark Port. This device is an adapter for the SLAC BADC (Brilliant Analog to Digital Converter) providing up to 5 ports whereas the BADC and SPORT takes signals from experimental equipment and directs them to other equipment and micro computers for processing and storing. These units are housed in standard Camac crates.

International Conference on Free Electron Lasers (11th) Conference Digest Held in Naples, Florida on 28 August-1 September 1989

DTIC Science & Technology

1989-12-01

Porn -20 t0 -2S0 kW arns, eavenate owev in Va nutcom,e ranged "mis -0.2 141 P2.19 DIRECT SPECTRAL MEASUREMENTS OF THE UCSS FEL G. Ramian and J. Hu...8217 . ~ ~ , . ., U M-MIRROR VID - -1T VIDEO DIC.ITI2EFN__________________________ TV- TV CAMERA MM -128 KBIYTE MEMORY MN-’ MONITOR IF - PI8 TO CAMAC IN

New data acquisition system for the focal plane polarimeter of the Grand Raiden spectrometer

NASA Astrophysics Data System (ADS)

Tamii, A.; Sakaguchi, H.; Takeda, H.; Yosoi, M.; Akimune, H.; Fujiwara, M.; Ogata, H.; Tanaka, M.; Togawa, H.

1996-10-01

This paper describes a new data acquisition system for the focal plane polarimeter of the Grand Raiden spectrometer at the Research Center for Nuclear Physics (RCNP) in Osaka, Japan. Data are acquired by a Creative Electronic Systems (CES) Starburst, which is a CAMAC auxiliary crate controller equipped with a Digital Equipment Corporation (DEC) J11 microprocessor. The data on the Starburst are transferred to a VME single-board computer. A VME reflective memory module broadcasts the data to other systems through a fiber-optic link. A data transfer rate of 2.0 Mbytes/s between VME modules has been achieved by reflective memories. This rate includes the overhead of buffer management. The overall transfer rate, however, is limited by the performance of the Starburst to about 160 Kbytes/s at maximum. In order to further improve the system performance, we developed a new readout module called the Rapid Data Transfer Module (RDTM). RDTM's transfer data from LeCroy PCOS III's or 4298's, and FERA/FERET's directly to CES 8170 High Speed Memories (HSM) in VME crates, the data transfer rate of the RDTM from PCOS III's to the HSM is about 4 Mbytes/s.

Cost effective, high performance transient recorder systems, utilizing the latest ADC`s, S/H`s, memories and PLA`s; Final report, May 14, 1987--February 14, 1990

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joerger, F. A.

1990-02-01

This project was to develop five transient recorder modules of various speeds and features. Four of the modules; TR200, 200MHZ recorder; TR2/25, Dual 25MHZ recorder; TR1012, 10MHZ, 12 bit recorder, and the ADC3216, 32 channel, 16 bit recorder were developed in the international CAMAC standard. The fifth unit, VTR1, 25MHZ recorder was packaged in the VME standard. Three of the modules, Models TR200, TR2/25 and VTR1 are already in Phase 3. The ADC3216 has been prototyped and successfully evaluated by a number of customers. The last module, Model TR1012, has been completely designed and the artwork completed. This module willmore » undergo tests shortly. 4 figs.« less

Upgrade to the control system of the reflectometry diagnostic of ASDEX upgrade

NASA Astrophysics Data System (ADS)

Graça, S.; Santos, J.; Manso, M. E.

2004-10-01

The broadband frequency modulation-continuous wave microwave/millimeter wave reflectometer of ASDEX upgrade tokamak (Institut für Plasma Physik (IPP), Garching, Germany) developed by Centro de Fusão Nuclear (Lisboa, Portugal) with the collaboration of IPP, is a complex system with 13 channels (O and X modes) and two types of operation modes (swept and fixed frequency). The control system that ensures remote operation of the diagnostic incorporates VME and CAMAC bus based acquisition/timing systems. Microprocessor input/output boards are used to control and monitor the microwave circuitry and associated electronic devices. The implementation of the control system is based on an object-oriented client/server model: a centralized server manages the hardware and receives input from remote clients. Communication is handled through transmission control protocol/internet protocol sockets. Here we describe recent upgrades of the control system aiming to: (i) accommodate new channels; (ii) adapt to the heterogeneity of computing platforms and operating systems; and (iii) overcome remote access restrictions. Platform and operating system independence was achieved by redesigning the graphical user interface in JAVA. As secure shell is the standard remote access protocol adopted in major fusion laboratories, secure shell tunneling was implemented to allow remote operation of the diagnostic through the existing firewalls.

Data Acquisition Software for Experiments at the MAMI-C Tagged Photon Facility

NASA Astrophysics Data System (ADS)

Oussena, Baya; Annand, John

2013-10-01

Tagged-photon experiments at Mainz use the electron beam of the MAMI (Mainzer MIcrotron) accelerator, in combination with the Glasgow Tagged Photon Spectrometer. The AcquDAQ DAQ system is implemented in the C + + language and makes use of CERN ROOT software libraries and tools. Electronic hardware is characterized in C + + classes, based on a general purpose class TDAQmodule and implementation in an object-oriented framework makes the system very flexible. The DAQ system provides slow control and event-by-event readout of the Photon Tagger, the Crystal Ball 4-pi electromagnetic calorimeter, central MWPC tracker and plastic-scintillator, particle-ID systems and the TAPS forward-angle calorimeter. A variety of front-end controllers running Linux are supported, reading data from VMEbus, FASTBUS and CAMAC systems. More specialist hardware, based on optical communication systems and developed for the COMPASS experiment at CERN, is also supported. AcquDAQ also provides an interface to configure and control the Mainz programmable trigger system, which uses FPGA-based hardware developed at GSI. Currently the DAQ system runs at data rates of up to 3MB/s and, with upgrades to both hardware and software later this year, we anticipate a doubling of that rate. This work was supported in part by the U.S. DOE Grant No. DE-FG02-99ER41110.

Advanced Detector and Waveform Digitizer for Water Vapor DIAL Systems

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Luck, William S., Jr.; DeYoung, Russell J.

1998-01-01

Measurement of atmospheric water vapor has become a major requirement for understanding moist-air processes. Differential absorption lidar (DIAL) is a technique best suited for the measurement of atmospheric water vapor. NASA Langley Research Center is continually developing improved DIAL systems. One aspect of current development is focused on the enhancement of a DIAL receiver by applying state-of-the-art technology in building a new compact detection system that will be placed directly on the DIAL receiver telescope. The newly developed detection system has the capability of being digitally interfaced with a simple personal computer, using a discrete input/output interface. This has the potential of transmitting digital data over relatively long distances instead of analog signals, which greatly reduces measurement noise. In this paper, we discuss some results from the new compact water vapor DIAL detection system which includes a silicon based avalanche photodiode (APD) detector, a 14-bit, 10-MHz waveform digitizer, a microcontroller and other auxiliary electronics. All of which are contained on a small printed-circuit-board. This will significantly reduce the weight and volume over the current CAMAC system and eventually will be used in a water vapor DIAL system on an unpiloted atmospheric vehicle (UAV) aircraft, or alternatively on an orbiting spacecraft.

Novel apparatus and methods for performing remotely controlled particle-solid interaction experiments at CERN

NASA Astrophysics Data System (ADS)

Krause, H. F.; Deveney, E. F.; Jones, N. L.; Vane, C. R.; Datz, S.; Knudsen, H.; Grafström, P.; Schuch, R.

1997-04-01

Recent atomic physics studies involving ultrarelativistic Pb ions required solid target positioners, scintillators, and a sophisticated data acquisition and control system placed in a remote location at the CERN Super Proton Synchrotron near Geneva, Switzerland. The apparatus, installed in a high-radiation zone underground, had to (i) function for months, (ii) automatically respond to failures such as power outages and particle-induced computer upsets, and (iii) communicate with the outside world via a telephone line. The heart of the apparatus developed was an Apple Macintosh-based CAMAC system that answered the telephone and interpreted and executed remote control commands that (i) sensed and set targets, (ii) controlled voltages and discriminator levels for scintillators, (iii) modified data acquisition hardware logic, (iv) reported control information, and (v) automatically synchronized data acquisition to the CERN spill cycle via a modem signal and transmitted experimental data to a remote computer. No problems were experienced using intercontinental telephone connections at 1200 baud. Our successful "virtual laboratory" approach that uses off-the-shelf electronics is generally adaptable to more conventional bench-type experiments.

New data acquisition system for the focal plane polarimeter of the Grand Raiden spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamii, A.; Sakaguchi, H.; Takeda, H.

1996-10-01

This paper describes a new data acquisition system for the focal plane polarimeter of the Grand Raiden spectrometer at the Research Center for Nuclear Physics (RCNP) in Osaka, Japan. Data are acquired by a Creative Electronic Systems (CES) Starburst, which is a CAMAC auxiliary crate controller equipped with a Digital Equipment Corporation (DEC) J11 microprocessor., The data on the Starburst are transferred to a VME single-board computer. A VME reflective memory module broadcasts the data to other systems through a fiber-optic link. A data transfer rate of 2.0 Mbytes/s between VME modules has been achieved by reflective memories. This ratemore » includes the overhead of buffer management. The overall transfer rate, however, is limited by the performance of the Starburst to about 160 Kbytes/s at maximum. In order to further improve the system performance, the authors developed a new readout module called the Rapid Data Transfer Module (RDTM). RDTM`s transfer data from LeCroy PCOS III`s or 4298`s, and FERA/FERET`s directly to CES 8170 High Speed Memories (HSM) in VME crates. The data transfer rate of the RDTM from PCOS III`s to the HSM is about 4 Mbytes/s.« less

Fieldable computer system for determining gamma-ray pulse-height distributions, flux spectra, and dose rates from Little Boy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moss, C.E.; Lucas, M.C.; Tisinger, E.W.

1984-01-01

Our system consists of a LeCroy 3500 data acquisition system with a built-in CAMAC crate and eight bismuth-germanate detectors 7.62 cm in diameter and 7.62 cm long. Gamma-ray pulse-height distributions are acquired simultaneously for up to eight positions. The system was very carefully calibrated and characterized from 0.1 to 8.3 MeV using gamma-ray spectra from a variety of radioactive sources. By fitting the pulse-height distributions from the sources with a function containing 17 parameters, we determined theoretical repsonse functions. We use these response functions to unfold the distributions to obtain flux spectra. A flux-to-dose-rate conversion curve based on the workmore » of Dimbylow and Francis is then used to obtain dose rates. Direct use of measured spectra and flux-to-dose-rate curves to obtain dose rates avoids the errors that can arise from spectrum dependence in simple gamma-ray dosimeter instruments. We present some gamma-ray doses for the Little Boy assembly operated at low power. These results can be used to determine the exposures of the Hiroshima survivors and thus aid in the establishment of radation exposure limits for the nuclear industry.« less

Automatic control of a negative ion source

NASA Astrophysics Data System (ADS)

Saadatmand, K.; Sredniawski, J.; Solensten, L.

1989-04-01

A CAMAC based control architecture is devised for a Berkeley-type H - volume ion source [1]. The architecture employs three 80386 TM PCs. One PC is dedicated to control and monitoring of source operation. The other PC functions with digitizers to provide data acquisition of waveforms. The third PC is used for off-line analysis. Initially, operation of the source was put under remote computer control (supervisory). This was followed by development of an automated startup procedure. Finally, a study of the physics of operation is now underway to establish a data base from which automatic beam optimization can be derived.

PCDAQ, A Windows Based DAQ System

NASA Astrophysics Data System (ADS)

Hogan, Gary

1998-10-01

PCDAQ is a Windows NT based general DAQ/Analysis/Monte Carlo shell developed as part of the Proton Radiography project at LANL (Los Alamos National Laboratory). It has been adopted by experiments outside of the Proton Radiography project at Brookhaven National Laboratory (BNL) and at LANL. The program provides DAQ, Monte Carlo, and replay (disk file input) modes. Data can be read from hardware (CAMAC) or other programs (ActiveX servers). Future versions will read VME. User supplied data analysis routines can be written in Fortran, C++, or Visual Basic. Histogramming, testing, and plotting packages are provided. Histogram data can be exported to spreadsheets or analyzed in user supplied programs. Plots can be copied and pasted as bitmap objects into other Windows programs or printed. A text database keyed by the run number is provided. Extensive software control flags are provided so that the user can control the flow of data through the program. Control flags can be set either in script command files or interactively. The program can be remotely controlled and data accessed over the Internet through its ActiveX DCOM interface.

Software handlers for process interfaces

NASA Technical Reports Server (NTRS)

Bercaw, R. W.

1976-01-01

The principles involved in the development of software handlers for custom interfacing problems are discussed. Handlers for the CAMAC standard are examined in detail. The types of transactions that must be supported have been established by standards groups, eliminating conflicting requirements arising out of different design philosophies and applications. Implementation of the standard handlers has been facilititated by standardization of hardware. The necessary local processors can be placed in the handler when it is written or at run time by means of input/output directives, or they can be built into a high-performance input/output processor. The full benefits of these process interfaces will only be realized when software requirements are incorporated uniformly into the hardware.

The DISTO data acquisition system at SATURNE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balestra, F.; Bedfer, Y.; Bertini, R.

1998-06-01

The DISTO collaboration has built a large-acceptance magnetic spectrometer designed to provide broad kinematic coverage of multiparticle final states produced in pp scattering. The spectrometer has been installed in the polarized proton beam of the Saturne accelerator in Saclay to study polarization observables in the {rvec p}p {yields} pK{sup +}{rvec Y} (Y = {Lambda}, {Sigma}{sup 0} or Y{sup *}) reaction and vector meson production ({psi}, {omega} and {rho}) in pp collisions. The data acquisition system is based on a VME 68030 CPU running the OS/9 operating system, housed in a single VME crate together with the CAMAC interface, the triplemore » port ECL memories, and four RISC R3000 CPU. The digitization of signals from the detectors is made by PCOS III and FERA front-end electronics. Data of several events belonging to a single Saturne extraction are stored in VME triple-port ECL memories using a hardwired fast sequencer. The buffer, optionally filtered by the RISC R3000 CPU, is recorded on a DLT cassette by DAQ CPU using the on-board SCSI interface during the acceleration cycle. Two UNIX workstations are connected to the VME CPUs through a fast parallel bus and the Local Area Network. They analyze a subset of events for on-line monitoring. The data acquisition system is able to read and record 3,500 ev/burst in the present configuration with a dead time of 15%.« less

A tailored 200 parameter VME based data acquisition system for IBA at the Lund Ion Beam Analysis Facility - Hardware and software

NASA Astrophysics Data System (ADS)

Elfman, Mikael; Ros, Linus; Kristiansson, Per; Nilsson, E. J. Charlotta; Pallon, Jan

2016-03-01

With the recent advances towards modern Ion Beam Analysis (IBA), going from one- or few-parameter detector systems to multi-parameter systems, it has been necessary to expand and replace the more than twenty years old CAMAC based system. A new VME multi-parameter (presently up to 200 channels) data acquisition and control system has been developed and implemented at the Lund Ion Beam Analysis Facility (LIBAF). The system is based on the VX-511 Single Board Computer (SBC), acting as master with arbiter functionality and consists of standard VME modules like Analog to Digital Converters (ADC's), Charge to Digital Converters (QDC's), Time to Digital Converters (TDC's), scaler's, IO-cards, high voltage and waveform units. The modules have been specially selected to support all of the present detector systems in the laboratory, with the option of future expansion. Typically, the detector systems consist of silicon strip detectors, silicon drift detectors and scintillator detectors, for detection of charged particles, X-rays and γ-rays. The data flow of the raw data buffers out from the VME bus to the final storage place on a 16 terabyte network attached storage disc (NAS-disc) is described. The acquisition process, remotely controlled over one of the SBCs ethernet channels, is also discussed. The user interface is written in the Kmax software package, and is used to control the acquisition process as well as for advanced online and offline data analysis through a user-friendly graphical user interface (GUI). In this work the system implementation, layout and performance are presented. The user interface and possibilities for advanced offline analysis are also discussed and illustrated.

The Fermilab Accelerator control system

NASA Astrophysics Data System (ADS)

Bogert, Dixon

1986-06-01

With the advent of the Tevatron, considerable upgrades have been made to the controls of all the Fermilab Accelerators. The current system is based on making as large an amount of data as possible available to many operators or end-users. Specifically there are about 100 000 separate readings, settings, and status and control registers in the various machines, all of which can be accessed by seventeen consoles, some in the Main Control Room and others distributed throughout the complex. A "Host" computer network of approximately eighteen PDP-11/34's, seven PDP-11/44's, and three VAX-11/785's supports a distributed data acquisition system including Lockheed MAC-16's left from the original Main Ring and Booster instrumentation and upwards of 1000 Z80, Z8002, and M68000 microprocessors in dozens of configurations. Interaction of the various parts of the system is via a central data base stored on the disk of one of the VAXes. The primary computer-hardware communication is via CAMAC for the new Tevatron and Antiproton Source; certain subsystems, among them vacuum, refrigeration, and quench protection, reside in the distributed microprocessors and communicate via GAS, an in-house protocol. An important hardware feature is an accurate clock system making a large number of encoded "events" in the accelerator supercycle available for both hardware modules and computers. System software features include the ability to save the current state of the machine or any subsystem and later restore it or compare it with the state at another time, a general logging facility to keep track of specific variables over long periods of time, detection of "exception conditions" and the posting of alarms, and a central filesharing capability in which files on VAX disks are available for access by any of the "Host" processors.

Fast wire per wire X-ray data acquisition system for time-resolved small angle scattering experiments

NASA Astrophysics Data System (ADS)

Epstein, A.; Briquet-Laugier, F.; Sheldon, S.; Boulin, C.

2000-04-01

Most of the X-ray multi-wire gas detectors used at the EMBL Hamburg outstation for time-resolved studies of biological samples are readout, using the delay line method. The main disadvantage of such readout systems is their event rate limitation introduced by the delay line and the required time to digital conversion step. They also lack the possibility to deal with multiple events. To overcome these limitations, a new approach for the complete readout system was introduced. The new linear detection system is based on the wire per wire approach where each individual wire is associated to preamplifier/discriminator/counter electronics channel. High-density, front-end electronics were designed around a fast current sensitive preamplifier. An eight-channel board was designed to include the preamplifiers-discriminators and the differential ECL drivers output stages. The detector front-end consists of 25 boards directly mounted inside the detector assembly. To achieve a time framing resolution as short as 10 /spl mu/s, very fast histogramming is required. The only way to implement this for a high number of channels (200 in our case) is by using a distributed system. The digital part of the system consists of a crate controller, up to 16 acquisition boards (capable of handling fast histogramming for up to 32-channels each) and an optical-link board (based on the Cypress "Hot-Link" chip set). Both the crate controller and the acquisition boards are based on a standard RISC microcontroller (IDT R3081) plug-in board. At present, a dedicated CAMAC module which we developed is used to interface the digital front-end acquisition crate to the host via the optical link.

High performance real-time flight simulation at NASA Langley

NASA Technical Reports Server (NTRS)

Cleveland, Jeff I., II

1994-01-01

In order to meet the stringent time-critical requirements for real-time man-in-the-loop flight simulation, computer processing operations must be deterministic and be completed in as short a time as possible. This includes simulation mathematical model computational and data input/output to the simulators. In 1986, in response to increased demands for flight simulation performance, personnel at NASA's Langley Research Center (LaRC), working with the contractor, developed extensions to a standard input/output system to provide for high bandwidth, low latency data acquisition and distribution. The Computer Automated Measurement and Control technology (IEEE standard 595) was extended to meet the performance requirements for real-time simulation. This technology extension increased the effective bandwidth by a factor of ten and increased the performance of modules necessary for simulator communications. This technology is being used by more than 80 leading technological developers in the United States, Canada, and Europe. Included among the commercial applications of this technology are nuclear process control, power grid analysis, process monitoring, real-time simulation, and radar data acquisition. Personnel at LaRC have completed the development of the use of supercomputers for simulation mathematical model computational to support real-time flight simulation. This includes the development of a real-time operating system and the development of specialized software and hardware for the CAMAC simulator network. This work, coupled with the use of an open systems software architecture, has advanced the state of the art in real time flight simulation. The data acquisition technology innovation and experience with recent developments in this technology are described.

Participation in the ARGUS experiment at the DORIS collider at DESY, Hamburg, Germany

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darden, C.

1986-03-27

Progress reported for 1985 includes publishing final results for investigation of F mesons. Particle decays were sought including a gamma line at 9.46 GeV. One such decay was Upsilon(1S)..--> gamma..H/sup 0/. A search for fractionally charged particles is reported. The muon pair branching ratio was determined for decays of the Upsilon(2S). Six anti-deuterons were seen in a data sample of over 720,000 electron-positron annihilation events. A clear D/sup 0/ signal was seen in the K/sup +/K/sup -/ channel. Results were obtained for the radiative transitions from the Upsilon(2S) to the 1/sup 3/P states of the banti-b system. Fifteen events weremore » also seen which were interpreted to be the color suppressed decay of a B meson to J/psi. A new upper limit was set for the mass of the tau neutrino. A CAMAC booster was used to reduce dead time in the experiment. New preamplifiers raised the vertex drift chambers enough above the electromagnetic noise of the storage ring that it was no longer a problem. The performance of the inner compensation coils, storage ring, and main drift chamber are reported, as well as the time of flight, shower, and muon counters. (LEW)« less

Use of high performance networks and supercomputers for real-time flight simulation

NASA Technical Reports Server (NTRS)

Cleveland, Jeff I., II

1993-01-01

In order to meet the stringent time-critical requirements for real-time man-in-the-loop flight simulation, computer processing operations must be consistent in processing time and be completed in as short a time as possible. These operations include simulation mathematical model computation and data input/output to the simulators. In 1986, in response to increased demands for flight simulation performance, NASA's Langley Research Center (LaRC), working with the contractor, developed extensions to the Computer Automated Measurement and Control (CAMAC) technology which resulted in a factor of ten increase in the effective bandwidth and reduced latency of modules necessary for simulator communication. This technology extension is being used by more than 80 leading technological developers in the United States, Canada, and Europe. Included among the commercial applications are nuclear process control, power grid analysis, process monitoring, real-time simulation, and radar data acquisition. Personnel at LaRC are completing the development of the use of supercomputers for mathematical model computation to support real-time flight simulation. This includes the development of a real-time operating system and development of specialized software and hardware for the simulator network. This paper describes the data acquisition technology and the development of supercomputing for flight simulation.

Modern design of a fast front-end computer

NASA Astrophysics Data System (ADS)

Šoštarić, Z.; Anic̈ić, D.; Sekolec, L.; Su, J.

1994-12-01

Front-end computers (FEC) at Paul Scherrer Institut provide access to accelerator CAMAC-based sensors and actuators by way of a local area network. In the scope of the new generation FEC project, a front-end is regarded as a collection of services. The functionality of one such service is described in terms of Yourdon's environment, behaviour, processor and task models. The computational model (software representation of the environment) of the service is defined separately, using the information model of the Shlaer-Mellor method, and Sather OO language. In parallel with the analysis and later with the design, a suite of test programmes was developed to evaluate the feasibility of different computing platforms for the project and a set of rapid prototypes was produced to resolve different implementation issues. The past and future aspects of the project and its driving forces are presented. Justification of the choice of methodology, platform and requirement, is given. We conclude with a description of the present state, priorities and limitations of our project.

Development of a remote control console for the HHIRF 25-MV tandem accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasanul Basher, A.M.

1991-09-01

The CAMAC-based control system for the 25-MV Tandem Accelerator at HHIRF uses two Perkin-Elmer, 32-bit minicomputers: a message-switching computer and a supervisory computer. Two operator consoles are located on one of the six serial highways. Operator control is provided by means of a console CRT, trackball, assignable shaft encoders and meters. The message-switching computer transmits and receives control information on the serial highways. At present, the CRT pages with updated parameters can be displayed and parameters can be controlled only from the two existing consoles, one in the Tandem control room and the other in the ORIC control room. Itmore » has become necessary to expand the control capability to several other locations in the building. With the expansion of control and monitoring capability of accelerator parameters to other locations, the operators will be able to control and observe the result of the control action at the same time. Since the new control console will be PC-based, the existing page format will be changed. The PC will be communicating with the Perkin-Elmer through RS-232 and a communication software package. Hardware configuration has been established, a communication software program that reads the pages from the shared memory has been developed. In this paper, we present the implementation strategy, works completed, existing and new page format, future action plans, explanation of pages and use of related global variables, a sample session, and flowcharts.« less

A remote control console for the HHIRF 25-MV Tandem Accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasanul Basher, A.M.

The CAMAC-based control system for the 25-MV Tandem Accelerator at HHIRF uses two Perkin-Elmer, 32-bit minicomputers: a message-switching computer and a supervisory computer. Two operator consoles are located on one of the six serial highways. Operator control is provided by means of a console CRT, trackball, assignable shaft encoders, and meters. The message-switching computer transmits and receives control information on the serial highways. At present, the CRT pages with updated parameters can be displayed and parameters can be controlled only from the two existing consoles, one in the Tandem control room and the other in the ORIC control room. Itmore » has become necessary to expand the control capability to several other locations in the building. With the expansion of control and monitoring capability of accelerator parameters to other locations, the operators will be able to control and observe the result of the control action at the same time. This capability will be useful in the new Radioactive Ion Beam project of the division. Since the new control console will be PC-based, the existing page format will be changed. The PC will be communicating with the Perkin-Elmer through RS-232 with the aid of a communication protocol. Hardware configuration has been established, a software program that reads the pages from the shared memory, and a communication protocol have been developed. The following sections present the implementation strategy, work completed, future action plans, and the functional details of the communication protocol.« less

A novel silicon array designed for intraoperative charged particle imaging.

PubMed

Tornai, Martin P; Patt, Bradley E; Iwanczyk, Jan S; Tull, Carolyn R; MacDonald, Lawrence R; Hoffman, Edward J

2002-11-01

A novel Si-PIN imaging array is under investigation for a charged particle (beta, positron, or alpha) sensitive intraoperative camera to be used for (residual) tumor identification during surgery. This class of collimator-less nuclear imaging device has a higher signal response for direct interactions than its scintillator-optical detector-based counterparts. Monte Carlo simulations with 635 keV betas were performed, yielding maximum and projected ranges of 1.64 and 0.55 mm in Si. Up to 90% of these betas were completely absorbed in the first 0.30 mm. Based on these results, 300 microm thick prototype Si detector arrays were designed in a 16 x 16 crossed-grid arrangement with 0.8 mm wide orthogonal strips on 1.0 mm pitch. A NIM- and CAMAC-based high-density data acquisition and processing system was used to collect the list mode data. The system was calibrated by comparisons of measured spectra to energy deposition simulations or by direct measurement of various >100 keV conversion electron or beta emitters. Mean electronic noise per strip was <3.6 keV FWHM at room temperature. When detecting positrons, which have an accompanying 511 keV annihilation background, the flood irradiated beta/gamma ratio was approximately 40, indicating that beta images could be made without the use of background rejection techniques. The intrinsic spatial resolution corresponds to the 1 x 1 mm2 pixel size, and measurements of beta emitting point and line sources yielded FWHM resolutions of 1.5 (lateral) and 2.5 mm (diagonal), respectively, with the larger widths due to particle range blurting effects. Deconvolution of the finite source size yielded intrinsic resolutions that corresponded to the image pixel size. Transmission images of circle and line phantoms with various hole sizes and pitch were resolved with either pure beta or positron irradiation without a background correction. This novel semiconductor imaging device facilitates high charged particle and low gamma sensitivity, high signal/noise ratio, and allows for compact design to potentially aid surgical guidance by providing in situ images of clinical relevance.

Setup and Calibration of SLAC's Peripheral Monitoring Stations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, C.

2004-09-03

The goals of this project were to troubleshoot, repair, calibrate, and establish documentation regarding SLAC's (Stanford Linear Accelerator Center's) PMS (Peripheral Monitoring Station) system. The PMS system consists of seven PMSs that continuously monitor skyshine (neutron and photon) radiation levels in SLAC's environment. Each PMS consists of a boron trifluoride (BF{sub 3}) neutron detector (model RS-P1-0802-104 or NW-G-20-12) and a Geiger Moeller (GM) gamma ray detector (model TGM N107 or LND 719) together with their respective electronics. Electronics for each detector are housed in Nuclear Instrument Modules (NIMs) and are plugged into a NIM bin in the station. All communicationmore » lines from the stations to the Main Control Center (MCC) were tested prior to troubleshooting. To test communication with MCC, a pulse generator (Systron Donner model 100C) was connected to each channel in the PMS and data at MCC was checked for consistency. If MCC displayed no data, the communication cables to MCC or the CAMAC (Computer Automated Measurement and Control) crates were in need of repair. If MCC did display data, then it was known that the communication lines were intact. All electronics from each station were brought into the lab for troubleshooting. Troubleshooting usually consisted of connecting an oscilloscope or scaler (Ortec model 871 or 775) at different points in the circuit of each detector to record simulated pulses produced by a pulse generator; the input and output pulses were compared to establish the location of any problems in the circuit. Once any problems were isolated, repairs were done accordingly. The detectors and electronics were then calibrated in the field using radioactive sources. Calibration is a process that determines the response of the detector. Detector response is defined as the ratio of the number of counts per minute interpreted by the detector to the amount of dose equivalent rate (in mrem per hour, either calculated or measured). Detector response for both detectors is dependent upon the energy of the incident radiation; this trend had to be accounted for in the calibration of the BF{sub 3} detector. Energy dependence did not have to be taken into consideration when calibrating the GM detectors since GM detector response is only dependent on radiation energy below 100 keV; SLAC only produces a spectrum of gamma radiation above 100 keV. For the GM detector, calibration consisted of bringing a {sup 137}Cs source and a NIST-calibrated RADCAL Radiation Monitor Controller (model 9010) out to the field; the absolute dose rate was determined by the RADCAL device while simultaneously irradiating the GM detector to obtain a scaler reading corresponding to counts per minute. Detector response was then calculated. Calibration of the BF{sub 3} detector was done using NIST certified neutron sources of known emission rates and energies. Five neutron sources ({sup 238}PuBe, {sup 238}PuB, {sup 238}PuF4, {sup 238}PuLi and {sup 252}Cf) with different energies were used to account for the energy dependence of the response. The actual neutron dose rate was calculated by date-correcting NIST source data and considering the direct dose rate and scattered dose rate. Once the total dose rate (sum of the direct and scattered dose rates) was known, the response vs. energy curve was plotted. The first station calibrated (PMS6) was calibrated with these five neutron sources; all subsequent stations were calibrated with one neutron source and the energy dependence was assumed to be the same.« less

a Search for Neutrino-Electron Elastic Scattering at the LAMPF Beam Stop.

NASA Astrophysics Data System (ADS)

Brooks, George Alfred

Neutrino-electron elastic scattering reactions play an important role in tests of weak interaction theory. The four reactions which may be considered are:. (nu)(,e) + e('-) (--->) (nu)(,e) + e('-). (nu)(,e)(' )+ e('-) (--->) (nu)(,e) + e('-). (nu)(,(mu)) + e('-) (--->) (nu)(,(mu)) + e('-). (nu)(,(mu))(' )+ e('-) (--->) (nu)(,(mu)) + e(' -). The experimental study of these purely leptonic interactions severely tests basic theoretical ideas, and the reaction with (nu)(,e) has not yet been observed. The characteristics of Los Alamos Meson Physics Facility. (LAMPF) are such that (nu)(,e) is rarely produced, whereas (nu)(,e),(nu)(,(mu)), and(' ). (nu)(,(mu)) are present in equal numbers. Thus, data on all three processes(' ). will be collected simultaneously, but the (nu)(,e) reaction is expected to dominate. However, such studies are exceedingly difficult. The main problem arises from the nature of the event signature (an undetected particle enters the detector producing a single recoil electron) coupled with the miniscule cross sections expected (and therefore low event rates) amid numerous sources of background events. To learn how to reduce the rates of such backgrounds, the UCI Neutrino Group installed in the Neutrino Facility in 1974 a small scale detector system consisting of a sandwich of optical spark chambers and plastic scintillator slabs (0.38 metric tons) which was shielded by 2 1/2" of Pb and enclosed by tanks of liquid scintillator used as an anticoincidence. Electronics and instrumentation, including a CAMAC system interfaced with a PDP-11/05 computer, were housed in a nearby trailer. The 1974 study was carried out with the LAMPF Neutrino Facility shielded against cosmic rays by Fe walls 3' thick and a 4' Fe roof. Nevertheless, stopping cosmic ray muons appeared to give rise to the substantial number of background electron events observed. Several techniques were invoked to reduce the potential background for neutrino -electron elastic scattering to (1.5 (+OR-) 0.5) day('-1). Improved statistics from 1976 gave (1.48 (+OR-) 0.34) day('-1). If this number could be further reduced--by additional shielding, for example--then the experiment would be easier. However, data taken in 1975 with varying thicknesses of Pb on top of the sandwich detector and in 1976 with an additional 1' of Fe on the roof showed that there is no significant advantage to having more Pb or Fe in those areas. The accelerator may also be a source of background. When the accelerator is operating, neutrons from the beam stop can penetrate the Fe shielding to produce an excessive trigger rate (energetic neutrons) or on excessive dead time (thermal neutrons), especially in the more massive ANTI required for the full scale experiment. However, data taken in 1974 with 10(mu)A accelerator current and 4m Fe as beam stop shielding, and in 1976 with 100 (mu)A and 5m Fe, showed that the neutron flux was well under control. The ultimate configuration requires much higher beam currents, but also calls for additional Fe so that neutrons will not be a problem. In both 1974 and 1976 there were no electron events remaining in the accelerator data following subtraction of cosmic ray background. This fact can be used to set an upper limit on the elastic scattering cross section for (nu)(,e):. (sigma)(,exp) < 38 (sigma)(,V-A) with 90% confidence. The results of these studies determined the amount of shielding required for a full scale neutrino experiment, established the need for a very efficient active anticoincidence, and aided the design of a 14.4 metric ton sandwich detector of flash chamber modules and plastic scintillator slabs. Developmental work for the full scale detector system began in 1977, and some of the subsequent construction work is still in progress. However, the Neutrino Facility has been prepared, and portions of the sandwich detector have been installed. The first information on neutrino -electron elastic scattering could be available by the middle of 1982.

Systems Integration Challenges for a National Space Launch System

NASA Technical Reports Server (NTRS)

May, Todd A.

2011-01-01

System Integration was refined through the complexity and early failures experienced in rocket flight. System Integration encompasses many different viewpoints of the system development. System Integration must ensure consistency in development and operations activities. Human Space Flight tends toward large, complex systems. Understanding the system fs operational and use context is the guiding principle for System Integration: (1) Sizeable costs can be driven into systems by not fully understanding context (2). Adhering to the system context throughout the system fs life cycle is essential to maintaining efficient System Integration. System Integration exists within the System Architecture. Beautiful systems are simple in use and operation -- Block upgrades facilitate manageable steps in functionality evolution. Effective System Integration requires a stable system concept. Communication is essential to system simplicity

Energy Systems Training Programs and Certifications Survey White Paper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cox, Daryl; Nimbalkar, Sachin U.; Wenning, Thomas J.

2017-02-01

Compressed air system, industrial refrigeration system, chilled water system, pump system, fan system, steam system, process heating system, and combined heat and power system are the major industrial energy systems. By helping enhance knowledge and skills of workforce, training and certification programs on these systems are essential to improve energy efficiency of manufacturing facilities. A literature survey of currently available training and certification programs on these systems was conducted.

Engineering Elegant Systems: Postulates, Principles, and Hypotheses of Systems Engineering

NASA Technical Reports Server (NTRS)

Watson, Michael D.

2018-01-01

Definition: System Engineering is the engineering discipline which integrates the system functions, system environment, and the engineering disciplines necessary to produce and/or operate an elegant system; Elegant System - A system that is robust in application, fully meeting specified and adumbrated intent, is well structured, and is graceful in operation. Primary Focus: System Design and Integration: Identify system couplings and interactions; Identify system uncertainties and sensitivities; Identify emergent properties; Manage the effectiveness of the system. Engineering Discipline Integration: Manage flow of information for system development and/or operations; Maintain system activities within budget and schedule. Supporting Activities: Process application and execution.

Systems Biology as an Integrated Platform for Bioinformatics, Systems Synthetic Biology, and Systems Metabolic Engineering

PubMed Central

Chen, Bor-Sen; Wu, Chia-Chou

2013-01-01

Systems biology aims at achieving a system-level understanding of living organisms and applying this knowledge to various fields such as synthetic biology, metabolic engineering, and medicine. System-level understanding of living organisms can be derived from insight into: (i) system structure and the mechanism of biological networks such as gene regulation, protein interactions, signaling, and metabolic pathways; (ii) system dynamics of biological networks, which provides an understanding of stability, robustness, and transduction ability through system identification, and through system analysis methods; (iii) system control methods at different levels of biological networks, which provide an understanding of systematic mechanisms to robustly control system states, minimize malfunctions, and provide potential therapeutic targets in disease treatment; (iv) systematic design methods for the modification and construction of biological networks with desired behaviors, which provide system design principles and system simulations for synthetic biology designs and systems metabolic engineering. This review describes current developments in systems biology, systems synthetic biology, and systems metabolic engineering for engineering and biology researchers. We also discuss challenges and future prospects for systems biology and the concept of systems biology as an integrated platform for bioinformatics, systems synthetic biology, and systems metabolic engineering. PMID:24709875

Systems biology as an integrated platform for bioinformatics, systems synthetic biology, and systems metabolic engineering.

PubMed

Chen, Bor-Sen; Wu, Chia-Chou

2013-10-11

Systems biology aims at achieving a system-level understanding of living organisms and applying this knowledge to various fields such as synthetic biology, metabolic engineering, and medicine. System-level understanding of living organisms can be derived from insight into: (i) system structure and the mechanism of biological networks such as gene regulation, protein interactions, signaling, and metabolic pathways; (ii) system dynamics of biological networks, which provides an understanding of stability, robustness, and transduction ability through system identification, and through system analysis methods; (iii) system control methods at different levels of biological networks, which provide an understanding of systematic mechanisms to robustly control system states, minimize malfunctions, and provide potential therapeutic targets in disease treatment; (iv) systematic design methods for the modification and construction of biological networks with desired behaviors, which provide system design principles and system simulations for synthetic biology designs and systems metabolic engineering. This review describes current developments in systems biology, systems synthetic biology, and systems metabolic engineering for engineering and biology researchers. We also discuss challenges and future prospects for systems biology and the concept of systems biology as an integrated platform for bioinformatics, systems synthetic biology, and systems metabolic engineering.

"If we're going to change things, it has to be systemic:" systems change in children's mental health.

PubMed

Hodges, Sharon; Ferreira, Kathleen; Israel, Nathaniel

2012-06-01

Communities that undertake systems change in accordance with the system of care philosophy commit to creating new systems entities for children and adolescents with serious emotional disturbance. These new entities are values-based, voluntary, and cross-agency alliances that include formal child-serving entities, youth, and families. Describing the scope and intent of one such implementation of systems of care, a mental health administrator commented, "If we're going to change things, it has to be systemic" (B. Baxter, personal communication, December 2, 2005). This paper explores the concept of "systemic" in the context of systems of care. Systems theory is used to understand strategies of purposeful systems change undertaken by stakeholders in established system of care communities. The paper presents a conceptual model of systems change for systems of care that is grounded in data from a national study of system of care implementation (Research and Training Center for Children's Mental Health in Case Studies of system implementation: Holistic approaches to studying community-based systems of care: Study 2, University of South Florida, Louis de la Parte Florida Mental Health Institute, Research and Training Center for Children's Mental Health, Tampa, FL, 2004). The model is based on Soft Systems Methodology, an application of systems theory developed to facilitate practical action around systems change in human systems (Checkland in Systems thinking, systems practice, Wiley, Chichester, 1999). The implications of these findings to real world actions associated with systems change in systems of care are discussed.

A Systems Approach to Biometrics in the Military Domain.

PubMed

Wilson, Lauren; Gahan, Michelle; Lennard, Chris; Robertson, James

2018-02-21

Forensic biometrics is the application of forensic science principles to physical and behavioral characteristics. Forensic biometrics is a secondary sub-system in the forensic science "system of systems," which describes forensic science as a sub-system in the larger criminal justice, law enforcement, intelligence, and military system. The purpose of this paper is to discuss biometrics in the military domain and integration into the wider forensic science system of systems. The holistic system thinking methodology was applied to the U.S. biometric system to map it to the system of systems framework. The U.S. biometric system is used as a case study to help guide other countries to develop military biometric systems that are integrated and interoperable at the whole-of-government level. The aim is to provide the system of systems framework for agencies to consider for proactive design of biometric systems. © 2018 American Academy of Forensic Sciences.

Industrial energy systems and assessment opportunities

NASA Astrophysics Data System (ADS)

Barringer, Frank Leonard, III

Industrial energy assessments are performed primarily to increase energy system efficiency and reduce energy costs in industrial facilities. The most common energy systems are lighting, compressed air, steam, process heating, HVAC, pumping, and fan systems, and these systems are described in this document. ASME has produced energy assessment standards for four energy systems, and these systems include compressed air, steam, process heating, and pumping systems. ASHRAE has produced an energy assessment standard for HVAC systems. Software tools for energy systems were developed for the DOE, and there are software tools for almost all of the most common energy systems. The software tools are AIRMaster+ and LogTool for compressed air systems, SSAT and 3E Plus for steam systems, PHAST and 3E Plus for process heating systems, eQUEST for HVAC systems, PSAT for pumping systems, and FSAT for fan systems. The recommended assessment procedures described in this thesis are used to set up an energy assessment for an industrial facility, collect energy system data, and analyze the energy system data. The assessment recommendations (ARs) are opportunities to increase efficiency and reduce energy consumption for energy systems. A set of recommended assessment procedures and recommended assessment opportunities are presented for each of the most common energy systems. There are many assessment opportunities for industrial facilities, and this thesis describes forty-three ARs for the seven different energy systems. There are seven ARs for lighting systems, ten ARs for compressed air systems, eight ARs for boiler and steam systems, four ARs for process heating systems, six ARs for HVAC systems, and four ARs for both pumping and fan systems. Based on a history of past assessments, average potential energy savings and typical implementation costs are shared in this thesis for most ARs. Implementing these ARs will increase efficiency and reduce energy consumption for energy systems in industrial facilities. This thesis does not explain all energy saving ARs that are available, but does describe the most common ARs.

Man-systems distributed system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Lewis, J. L.

1990-01-01

Viewgraphs on man-systems distributed system for Space Station Freedom are presented. Topics addressed include: description of man-systems (definition, requirements, scope, subsystems, and topologies); implementation (approach, tools); man-systems interfaces (system to element and system to system); prime/supporting development relationship; selected accomplishments; and technical challenges.

On domain modelling of the service system with its application to enterprise information systems

NASA Astrophysics Data System (ADS)

Wang, J. W.; Wang, H. F.; Ding, J. L.; Furuta, K.; Kanno, T.; Ip, W. H.; Zhang, W. J.

2016-01-01

Information systems are a kind of service systems and they are throughout every element of a modern industrial and business system, much like blood in our body. Types of information systems are heterogeneous because of extreme uncertainty in changes in modern industrial and business systems. To effectively manage information systems, modelling of the work domain (or domain) of information systems is necessary. In this paper, a domain modelling framework for the service system is proposed and its application to the enterprise information system is outlined. The framework is defined based on application of a general domain modelling tool called function-context-behaviour-principle-state-structure (FCBPSS). The FCBPSS is based on a set of core concepts, namely: function, context, behaviour, principle, state and structure and system decomposition. Different from many other applications of FCBPSS in systems engineering, the FCBPSS is applied to both infrastructure and substance systems, which is novel and effective to modelling of service systems including enterprise information systems. It is to be noted that domain modelling of systems (e.g. enterprise information systems) is a key to integration of heterogeneous systems and to coping with unanticipated situations facing to systems.

78 FR 68861 - Certain Navigation Products, Including GPS Devices, Navigation and Display Systems, Radar Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... Devices, Navigation and Display Systems, Radar Systems, Navigational Aids, Mapping Systems and Related... navigation products, including GPS devices, navigation and display systems, radar systems, navigational aids..., radar systems, navigational aids, mapping systems and related software by reason of infringement of one...

75 FR 75549 - Defense Federal Acquisition Regulation Supplement; Business Systems-Definition and Administration...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

... systems as accounting systems, estimating systems, purchasing systems, earned value management systems (EVMS), material management and accounting systems (MMAS), and property management systems. 2. DoD is... percent. 2. Accounting System Comment: A number of respondents expressed concern about the criteria to be...

Turbine airfoil cooling system with cooling systems using high and low pressure cooling fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marsh, Jan H.; Messmann, Stephen John; Scribner, Carmen Andrew

A turbine airfoil cooling system including a low pressure cooling system and a high pressure cooling system for a turbine airfoil of a gas turbine engine is disclosed. In at least one embodiment, the low pressure cooling system may be an ambient air cooling system, and the high pressure cooling system may be a compressor bleed air cooling system. In at least one embodiment, the compressor bleed air cooling system in communication with a high pressure subsystem that may be a snubber cooling system positioned within a snubber. A delivery system including a movable air supply tube may be usedmore » to separate the low and high pressure cooling subsystems. The delivery system may enable high pressure cooling air to be passed to the snubber cooling system separate from low pressure cooling fluid supplied by the low pressure cooling system to other portions of the turbine airfoil cooling system.« less

Reproducibility in a multiprocessor system

DOEpatents

Bellofatto, Ralph A; Chen, Dong; Coteus, Paul W; Eisley, Noel A; Gara, Alan; Gooding, Thomas M; Haring, Rudolf A; Heidelberger, Philip; Kopcsay, Gerard V; Liebsch, Thomas A; Ohmacht, Martin; Reed, Don D; Senger, Robert M; Steinmacher-Burow, Burkhard; Sugawara, Yutaka

2013-11-26

Fixing a problem is usually greatly aided if the problem is reproducible. To ensure reproducibility of a multiprocessor system, the following aspects are proposed; a deterministic system start state, a single system clock, phase alignment of clocks in the system, system-wide synchronization events, reproducible execution of system components, deterministic chip interfaces, zero-impact communication with the system, precise stop of the system and a scan of the system state.

Summary of compliant and multi-arm control at NASA. Langley Research Center

NASA Technical Reports Server (NTRS)

Harrison, Fenton W.

1992-01-01

The topics are presented in viewgraph form and include the: single arm system, single arm axis system, single arm control systems, single arm hand controller axis system, single arm position axis system, single arm vision axis system, single arm force axis system, multi-arm system, multi-arm axis system, and the dual arm hand control axis system with control signals.

77 FR 47641 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-09

...In accordance with the requirements of the Privacy Act of 1974, as amended (Privacy Act), the Federal Housing Finance Agency (FHFA) gives notice of and requests comments on the proposed revision of one existing system of records, the establishment of four new systems of records, and the removal of three existing systems of records notices. The revised existing system of records is ``Fraud Reporting System'' (FHFA-6). The proposed systems of records are: ``Visitor Badge, Employee and Contractor Personnel Day Pass, and Trackable Mail System'' (FHFA-17), ``Reasonable Accommodation Information System'' (FHFA-18), ``Computer Systems Activity and Access Records System'' (FHFA-19), and ``Telecommunications System'' (FHFA-20). In addition, upon the effective date of this notice, the Office of Federal Housing Enterprise Oversight systems of records notices, ``OFHEO-10 Reasonable Accommodation Information System'' (73 FR 19236 (April 9, 2008)), ``OFHEO-08 Computer Systems Activity and Access Records System'' (71 FR 6085 (February 6, 2006)), and ``OFHEO-09 Telecommunications System'' (71 FR 39123 (July 11, 2006)) will be removed.

Expanding Alternative Delivery Systems.

ERIC Educational Resources Information Center

Baltzer, Jan A.

Alternative educational delivery systems that might be useful to community colleges are considered. The following categories of delivery systems are covered: broadcast delivery systems; copy delivery systems, print delivery systems, computer delivery systems, telephone delivery systems, and satellites. Among the applications for broadcast…

Systems and Components Fuel Delivery System, Water Delivery System, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Systems and Components - Fuel Delivery System, Water Delivery System, Derrick Crane System, and Crane System Details - Marshall Space Flight Center, F-1 Engine Static Test Stand, On Route 565 between Huntsville and Decatur, Huntsville, Madison County, AL

Science for Iowa Schools, Grades 4-6.

ERIC Educational Resources Information Center

Nice, Karl; And Others

This guide includes four units for use in each of grades 4 through 6. The fourth grade units are entitled Measurement Systems, Classification Systems, Bio-Control Systems, and Hydrologic Systems; the fifth grade units are Chemical Systems, Force Systems, Bio-Systems, and Astro-Systems; and the sixth grade units are Equilibrium Systems,…

Sensitivities of projected 1980 photovoltaic system costs to major system cost drivers

NASA Technical Reports Server (NTRS)

Zimmerman, L. W.; Smith, J. L.

1984-01-01

The sensitivity of projected 1990 photovoltaic (PV) system costs to major system cost drivers was examined. It includes: (1) module costs and module efficiencies; (2) area related balance of system (BOS) costs; (3) inverter costs and efficiencies; and (4) module marketing and distribution markups and system integration fees. Recent PV system cost experiences and the high costs of electricity from the systems are reviewed. The 1990 system costs are projected for five classes of PV systems, including four ground mounted 5-MWp systems and one residential 5-kWp system. System cost projections are derived by first projecting costs and efficiencies for all subsystems and components. Sensitivity analyses reveal that reductions in module cost and engineering and system integration fees seem to have the greatest potential for contributing to system cost reduction. Although module cost is clearly the prime candidate for fruitful PV research and development activities, engineering and system integration fees seem to be more amenable to reduction through appropriate choice of system size and market strategy. Increases in inverter and module efficiency yield significant benefits, especially for systems with high area related costs.

Automatic computation of transfer functions

DOEpatents

Atcitty, Stanley; Watson, Luke Dale

2015-04-14

Technologies pertaining to the automatic computation of transfer functions for a physical system are described herein. The physical system is one of an electrical system, a mechanical system, an electromechanical system, an electrochemical system, or an electromagnetic system. A netlist in the form of a matrix comprises data that is indicative of elements in the physical system, values for the elements in the physical system, and structure of the physical system. Transfer functions for the physical system are computed based upon the netlist.

MSFC Skylab airlock module, volume 1. [systems design and performance

NASA Technical Reports Server (NTRS)

1974-01-01

The history and development of the Skylab Airlock Module and Payload Shroud is presented from initial concept through final design. A summary is given of the Airlock features and systems. System design and performance are presented for the Spent Stage Experiment Support Module, structure and mechanical systems, mass properties, thermal and environmental control systems, EVA/IVA suite system, electrical power system, sequential system, sequential system, and instrumentation system.

Comparison of MagNA Pure 96, Chemagic MSM1, and QIAamp MinElute for hepatitis B virus nucleic acid extraction.

PubMed

Kang, Seong-Ho; Lee, Eun Hee; Park, Geon; Jang, Sook Jin; Moon, Dae Soo

2012-01-01

This study was designed to compare two automated systems and one manual system for hepatitis B virus (HBV) nucleic acid extraction. The two automated systems were the MagNA Pure 96 system (Roche Applied Science, Manheim, Germany) and the Chemagic system (Chemagen, Baesweiler, Germany), and the manual system was the QIAamp system (Qiagen, Hilden, Germany). Sixty-eight samples that were within the detection range of the Cobas Ampliprep/Cobas TaqMan (CAP/CTM) platform (Roche Molecular Systems, Manheim, Germany) were selected. Extracted viral nucleic acids from the three systems were quantified using an AccuPower HBV Quantitative PCR kit (Bioneer, Daejon, Korea). The MagNA Pure 96 system and QIAamp system did not detect viral loads in one sample. The Chemagic system did not detect low viral loads in nine samples (range, 26-290 IU/mL by the CAP/CTM platform). Comparisons of the viral loads of the samples from the MagNA Pure 96 system, the Chemagic system, and the QIAamp system with those from the CAP/CTM platform yielded correlation coefficients of 0.977, 0.914, and 0.967, respectively. Comparisons of the MagNA Pure 96 system and the Chemagic system with the QIAamp system yielded correlation coefficients of 0.987 and 0.939, respectively. The MagNA Pure 96 system demonstrated better performance than the Chemagic system for HBV nucleic acid extraction. The MagNA Pure 96 system demonstrated comparable performance with the QIAamp system.

Human factor roles in design of teleoperator systems

NASA Technical Reports Server (NTRS)

Janow, C.; Malone, T. B.

1973-01-01

Teleoperator systems are considered, giving attention to types of teleoperators, a manned space vehicle attached manipulator, a free-flying teleoperator, a surface exploration roving vehicle, the human factors role in total system design, the manipulator system, the sensor system, the communication system, the control system, and the mobility system. The role of human factors in the development of teleoperator systems is also discussed, taking into account visual systems, an operator control station, and the manipulators.

A study of compositional verification based IMA integration method

NASA Astrophysics Data System (ADS)

Huang, Hui; Zhang, Guoquan; Xu, Wanmeng

2018-03-01

The rapid development of avionics systems is driving the application of integrated modular avionics (IMA) systems. But meanwhile it is improving avionics system integration, complexity of system test. Then we need simplify the method of IMA system test. The IMA system supports a module platform that runs multiple applications, and shares processing resources. Compared with federated avionics system, IMA system is difficult to isolate failure. Therefore, IMA system verification will face the critical problem is how to test shared resources of multiple application. For a simple avionics system, traditional test methods are easily realizing to test a whole system. But for a complex system, it is hard completed to totally test a huge and integrated avionics system. Then this paper provides using compositional-verification theory in IMA system test, so that reducing processes of test and improving efficiency, consequently economizing costs of IMA system integration.

Interaction of feel system and flight control system dynamics on lateral flying qualities

NASA Technical Reports Server (NTRS)

Bailey, Randall E.; Powers, Bruce G.; Shafer, Mary F.

1988-01-01

An investigation of feel system and flight control system dynamics on lateral flying qualities was conducted using the variable stability USAF NT-33 aircraft. Experimental variations in feel system natural frequency, force-deflection gradient, control system command architecture type, flight control system filter frequency, and control system delay were made. The experiment data include pilot ratings using the Cooper-Harper (1969) rating scale, pilot comments, and tracking performance statistic. Three test pilots served as evaluators. The data indicate that as the feel system natural frequency is reduced lateral flying qualities degrade. At the slowest feel system frequency, the closed-loop response becomes nonlinear with a 'bobweight' effect apparent in the feel system. Feel system influences were essentially independent of the control system architecture. The flying qualities influence due to the feel system was different than when the identical dynamic systenm was used as a flight control system element.

A contemporary view of systems engineering. [definition of system and discussion of systems approach

NASA Technical Reports Server (NTRS)

Miles, R. F., Jr.

1974-01-01

The concept of a 'system' is defined, and the 'systems approach' is discussed. Four contemporary examples of the systems approach are presented: an operations research project, the planning-programming-budgeting system, an information processing system, and aerospace programs.

5 CFR 1330.403 - System certification.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 5 Administrative Personnel 3 2013-01-01 2013-01-01 false System certification. 1330.403 Section....403 System certification. (a) The performance appraisal system(s) covering senior employees must be... certify an agency's appraisal system(s) only when a review of that system's design, application, and...

5 CFR 1330.403 - System certification.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 3 2014-01-01 2014-01-01 false System certification. 1330.403 Section....403 System certification. (a) The performance appraisal system(s) covering senior employees must be... certify an agency's appraisal system(s) only when a review of that system's design, application, and...

Is the system really the solution? Operating costs in hospital systems.

PubMed

Burns, Lawton Robert; McCullough, Jeffrey S; Wholey, Douglas R; Kruse, Gregory; Kralovec, Peter; Muller, Ralph

2015-06-01

Hospital system formation has recently accelerated. Executives emphasize scale economies that lower operating costs, a claim unsupported in academic research. Do systems achieve lower costs than freestanding facilities, and, if so, which system types? We test hypotheses about the relationship of cost with membership in systems, larger systems, and centralized and local hub-and-spoke systems. We also test whether these relationships have changed over time. Examining 4,000 U.S. hospitals during 1998 to 2010, we find no evidence that system members exhibit lower costs. However, members of smaller systems are lower cost than larger systems, and hospitals in centralized systems are lower cost than everyone else. There is no evidence that the system's spatial configuration is associated with cost, although national system hospitals exhibit higher costs. Finally, these results hold over time. We conclude that while systems in general may not be the solution to lower costs, some types of systems are. © The Author(s) 2015.

Sunitinib in Treating Young Patients With Refractory Solid Tumors

ClinicalTrials.gov

2014-01-27

Central Nervous System Metastases; Childhood Central Nervous System Choriocarcinoma; Childhood Central Nervous System Embryonal Tumor; Childhood Central Nervous System Germ Cell Tumor; Childhood Central Nervous System Germinoma; Childhood Central Nervous System Mixed Germ Cell Tumor; Childhood Central Nervous System Teratoma; Childhood Central Nervous System Yolk Sac Tumor; Recurrent Childhood Central Nervous System Embryonal Tumor; Unspecified Childhood Solid Tumor, Protocol Specific

Collaborative Systems Thinking: A Response to the Problems Faced by Systems Engineering's 'Middle Tier'

NASA Technical Reports Server (NTRS)

Phfarr, Barbara B.; So, Maria M.; Lamb, Caroline Twomey; Rhodes, Donna H.

2009-01-01

Experienced systems engineers are adept at more than implementing systems engineering processes: they utilize systems thinking to solve complex engineering problems. Within the space industry demographics and economic pressures are reducing the number of experienced systems engineers that will be available in the future. Collaborative systems thinking within systems engineering teams is proposed as a way to integrate systems engineers of various experience levels to handle complex systems engineering challenges. This paper uses the GOES-R Program Systems Engineering team to illustrate the enablers and barriers to team level systems thinking and to identify ways in which performance could be improved. Ways NASA could expand its engineering training to promote team-level systems thinking are proposed.

NASCOM system development plan: System description, capabilities, and plans, FY 94-2

NASA Technical Reports Server (NTRS)

1994-01-01

The Nascom System Development Plan (NSDP) for FY 94-2 contains 17 sections. It is a management document containing the approved plan for maintaining the Nascom Network System. Topics covered include an overview of Nascom systems and services, major ground communication support systems, low-speed data system, voice system, high-speed data system, Nascom support for NASA networks, Nascom planning for NASA missions, and network upgrade and advanced systems developments and plans.

What Factors Affect the Prices of Low-Priced U.S. Solar PV Systems?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemet, Gregory F.; O'Shaughnessy, Eric; Wiser, Ryan

The price of solar PV systems has declined rapidly, yet there are some much lower-priced systems than others. This study explores the factors leading some systems to be so much lower priced than others. Using a data set of 42,611 residential-scale PV systems installed in the U.S. in 2013, we use quantile regressions to estimate the importance of factors affecting the installed prices for low-priced (LP) systems (those at the 10th percentile) in comparison to median-priced systems. We find that the value of solar to consumers–a variable that accounts for subsidies, electric rates, and PV generation levels–is associated with lowermore » prices for LP systems but higher prices for median priced systems. Conversely, systems installed in new home construction are associated with lower prices at the median but higher prices for LP. Other variables have larger cost-reducing effects on LP than on median priced systems: systems installed in Arizona and Florida, as well as commercial and thin film systems. In contrast, the following have a smaller effect on prices for LP systems than median priced systems: tracking systems, self-installations, systems installed in Massachusetts, the system size, and installer experience. These results highlight the complex factors at play that lead to LP systems and shed light into how such LP systems can come about.« less

Exploration Medical System Technical Development

NASA Technical Reports Server (NTRS)

McGuire, K.; Middour, C.; Cerro, J.; Burba, T.; Hanson, A.; Reilly, J.; Mindock, J.

2017-01-01

The Exploration Medical Capability (ExMC) Element systems engineering goals include defining the technical system needed to implement exploration medical capabilities for Mars. This past year, scenarios captured in the medical system concept of operations laid the foundation for systems engineering technical development work. The systems engineering team analyzed scenario content to identify interactions between the medical system, crewmembers, the exploration vehicle, and the ground system. This enabled the definition of functions the medical system must provide and interfaces to crewmembers and other systems. These analyses additionally lead to the development of a conceptual medical system architecture. The work supports the ExMC community-wide understanding of the functional exploration needs to be met by the medical system, the subsequent development of medical system requirements, and the system verification and validation approach utilizing terrestrial analogs and precursor exploration missions.

Potential risk for bacterial contamination in conventional reused ventilator systems and disposable closed ventilator-suction systems.

PubMed

Li, Ya-Chi; Lin, Hui-Ling; Liao, Fang-Chun; Wang, Sing-Siang; Chang, Hsiu-Chu; Hsu, Hung-Fu; Chen, Sue-Hsien; Wan, Gwo-Hwa

2018-01-01

Few studies have investigated the difference in bacterial contamination between conventional reused ventilator systems and disposable closed ventilator-suction systems. The aim of this study was to investigate the bacterial contamination rates of the reused and disposable ventilator systems, and the association between system disconnection and bacterial contamination of ventilator systems. The enrolled intubated and mechanically ventilated patients used a conventional reused ventilator system and a disposable closed ventilator-suction system, respectively, for a week; specimens were then collected from the ventilator circuit systems to evaluate human and environmental bacterial contamination. The sputum specimens from patients were also analyzed in this study. The detection rate of bacteria in the conventional reused ventilator system was substantially higher than that in the disposable ventilator system. The inspiratory and expiratory limbs of the disposable closed ventilator-suction system had higher bacterial concentrations than the conventional reused ventilator system. The bacterial concentration in the heated humidifier of the reused ventilator system was significantly higher than that in the disposable ventilator system. Positive associations existed among the bacterial concentrations at different locations in the reused and disposable ventilator systems, respectively. The predominant bacteria identified in the reused and disposable ventilator systems included Acinetobacter spp., Bacillus cereus, Elizabethkingia spp., Pseudomonas spp., and Stenotrophomonas (Xan) maltophilia. Both the reused and disposable ventilator systems had high bacterial contamination rates after one week of use. Disconnection of the ventilator systems should be avoided during system operation to decrease the risks of environmental pollution and human exposure, especially for the disposable ventilator system. ClinicalTrials.gov PRS / NCT03359148.

Evaluation of the sustainability of contrasted pig farming systems: breeding programmes.

PubMed

Rydhmer, L; Gourdine, J L; de Greef, K; Bonneau, M

2014-12-01

The sustainability of breeding activities in 15 pig farming systems in five European countries was evaluated. One conventional and two differentiated systems per country were studied. The Conventional systems were the standard systems in their countries. The differentiated systems were of three categories: Adapted Conventional with focus on animal welfare, meat quality or environment (five systems); Traditional with local breeds in small-scale production (three systems) and Organic (two systems). Data were collected with a questionnaire from nine breeding organisations providing animals and semen to the studied farming systems and from, on average, five farmers per farming system. The sustainability assessment of breeding activities was performed in four dimensions. The first dimension described whether the market for the product was well defined, and whether the breeding goal reflected the farming system and the farmers' demands. The second dimension described recording and selection procedures, together with genetic change in traits that were important in the system. The third dimension described genetic variation, both within and between pig breeds. The fourth dimension described the management of the breeding organisation, including communication, transparency, and technical and human resources. The results show substantial differences in the sustainability of breeding activities, both between farming systems within the same category and between different categories of farming systems. The breeding activities are assessed to be more sustainable for conventional systems than for differentiated systems in three of the four dimensions. In most differentiated farming systems, breeding goals are not related to the system, as these systems use the same genetic material as conventional systems. The breeds used in Traditional farming systems are important for genetic biodiversity, but the small scale of these systems renders them vulnerable. It is hoped that, by reflecting on different aspects of sustainability, this study will encourage sustainable developments in pig production.

The Systems Engineering Process for Human Support Technology Development

NASA Technical Reports Server (NTRS)

Jones, Harry

2005-01-01

Systems engineering is designing and optimizing systems. This paper reviews the systems engineering process and indicates how it can be applied in the development of advanced human support systems. Systems engineering develops the performance requirements, subsystem specifications, and detailed designs needed to construct a desired system. Systems design is difficult, requiring both art and science and balancing human and technical considerations. The essential systems engineering activity is trading off and compromising between competing objectives such as performance and cost, schedule and risk. Systems engineering is not a complete independent process. It usually supports a system development project. This review emphasizes the NASA project management process as described in NASA Procedural Requirement (NPR) 7120.5B. The process is a top down phased approach that includes the most fundamental activities of systems engineering - requirements definition, systems analysis, and design. NPR 7120.5B also requires projects to perform the engineering analyses needed to ensure that the system will operate correctly with regard to reliability, safety, risk, cost, and human factors. We review the system development project process, the standard systems engineering design methodology, and some of the specialized systems analysis techniques. We will discuss how they could apply to advanced human support systems development. The purpose of advanced systems development is not directly to supply human space flight hardware, but rather to provide superior candidate systems that will be selected for implementation by future missions. The most direct application of systems engineering is in guiding the development of prototype and flight experiment hardware. However, anticipatory systems engineering of possible future flight systems would be useful in identifying the most promising development projects.

78 FR 18252 - Prevailing Rate Systems; North American Industry Classification System Based Federal Wage System...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-26

...-AM78 Prevailing Rate Systems; North American Industry Classification System Based Federal Wage System... 2007 North American Industry Classification System (NAICS) codes currently used in Federal Wage System... (OPM) issued a final rule (73 FR 45853) to update the 2002 North American Industry Classification...

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Remote Stopping Systems § 111.103-1 Power ventilation systems except machinery space ventilation systems. Each power ventilation system must... 46 Shipping 4 2010-10-01 2010-10-01 false Power ventilation systems except machinery space...

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Remote Stopping Systems § 111.103-1 Power ventilation systems except machinery space ventilation systems. Each power ventilation system must... 46 Shipping 4 2011-10-01 2011-10-01 false Power ventilation systems except machinery space...

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Remote Stopping Systems § 111.103-1 Power ventilation systems except machinery space ventilation systems. Each power ventilation system must... 46 Shipping 4 2014-10-01 2014-10-01 false Power ventilation systems except machinery space...

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Remote Stopping Systems § 111.103-1 Power ventilation systems except machinery space ventilation systems. Each power ventilation system must... 46 Shipping 4 2012-10-01 2012-10-01 false Power ventilation systems except machinery space...

46 CFR 111.103-1 - Power ventilation systems except machinery space ventilation systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Remote Stopping Systems § 111.103-1 Power ventilation systems except machinery space ventilation systems. Each power ventilation system must... 46 Shipping 4 2013-10-01 2013-10-01 false Power ventilation systems except machinery space...

Systems autonomy

NASA Technical Reports Server (NTRS)

Lum, Henry, Jr.

1988-01-01

Information on systems autonomy is given in viewgraph form. Information is given on space systems integration, intelligent autonomous systems, automated systems for in-flight mission operations, the Systems Autonomy Demonstration Project on the Space Station Thermal Control System, the architecture of an autonomous intelligent system, artificial intelligence research issues, machine learning, and real-time image processing.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curry, J J; Gallagher, D W; Modarres, M

Appendices are presented concerning isolation condenser makeup; vapor suppression system; station air system; reactor building closed cooling water system; turbine building secondary closed water system; service water system; emergency service water system; fire protection system; emergency ac power; dc power system; event probability estimation; methodology of accident sequence quantification; and assignment of dominant sequences to release categories.

Supervisory Control and Data Acquisition System | Energy Systems

Science.gov Websites

Integration Facility | NREL Supervisory Control and Data Acquisition System Supervisory Control supervisory control and data acquisition (SCADA) system monitors and controls safety systems and gathers real Energy Systems Integration Facility control room. The Energy Systems Integration Facility's SCADA system

A Description of the Environmental Protection Agency's In-House Library Systems.

ERIC Educational Resources Information Center

Thomas, Sarah M.; Needle, Lester P.

The Environmental Protection Agency's (EPA) inhouse library systems fall into two principle categories: basic library inventory systems and literature retrieval systems. Currently, the library network supports three inventory systems: the journal system; the hard bound book system; and the circulation system. At the same time, five efforts are…

WASTE TREATMENT BUILDING SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

F. Habashi

2000-06-22

The Waste Treatment Building System provides the space, layout, structures, and embedded subsystems that support the processing of low-level liquid and solid radioactive waste generated within the Monitored Geologic Repository (MGR). The activities conducted in the Waste Treatment Building include sorting, volume reduction, and packaging of dry waste, and collecting, processing, solidification, and packaging of liquid waste. The Waste Treatment Building System is located on the surface within the protected area of the MGR. The Waste Treatment Building System helps maintain a suitable environment for the waste processing and protects the systems within the Waste Treatment Building (WTB) from mostmore » of the natural and induced environments. The WTB also confines contaminants and provides radiological protection to personnel. In addition to the waste processing operations, the Waste Treatment Building System provides space and layout for staging of packaged waste for shipment, industrial and radiological safety systems, control and monitoring of operations, safeguards and security systems, and fire protection, ventilation and utilities systems. The Waste Treatment Building System also provides the required space and layout for maintenance activities, tool storage, and administrative facilities. The Waste Treatment Building System integrates waste processing systems within its protective structure to support the throughput rates established for the MGR. The Waste Treatment Building System also provides shielding, layout, and other design features to help limit personnel radiation exposures to levels which are as low as is reasonably achievable (ALARA). The Waste Treatment Building System interfaces with the Site Generated Radiological Waste Handling System, and with other MGR systems that support the waste processing operations. The Waste Treatment Building System interfaces with the General Site Transportation System, Site Communications System, Site Water System, MGR Site Layout, Safeguards and Security System, Site Radiological Monitoring System, Site Electrical Power System, Site Compressed Air System, and Waste Treatment Building Ventilation System.« less

Interoperable Acquisition for Systems of Systems: The Challenges

DTIC Science & Technology

2006-09-01

Interoperable Acquisition for Systems of Systems: The Challenges James D. Smith II D. Mike Phillips September 2006 TECHNICAL NOTE...Failure of Program-Centric Risk Management 10 3.3.2 Absence of System-of-Systems Engineering 12 3.3.3 Disconnect Between System-of-Systems...SOFTWARE ENGINEERING INSTITUTE | vii viii | CMU/SEI-2006-TN-034 Abstract Large, complex systems development has always been challenging , even when the

A Systems Thinking Approach to Engineering Challenges of Military Systems-of-Systems

DTIC Science & Technology

2016-09-01

UNCLASSIFIED UNCLLASIFIED A Systems Thinking Approach to Engineering Challenges of Military Systems -of- Systems Pin Chen and Mark...Unewisse Joint & Operations Analysis Division Defence Science and Technology Group DST-Group-TR-3271 ABSTRACT System (s)-of- Systems (SoS...their products and outcomes. This report introduces a systems thinking-based approach, SoS thinking, which offers a language and a thoughtful process

Comparison of Mars Aircraft Propulsion Systems

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.

2003-01-01

The propulsion system is a critical aspect of the performance and feasibility of a Mars aircraft. Propulsion system mass and performance greatly influence the aircraft s design and mission capabilities. Various propulsion systems were analyzed to estimate the system mass necessary for producing 35N of thrust within the Mars environment. Three main categories of propulsion systems were considered: electric systems, combustion engine systems and rocket systems. Also, the system masses were compared for mission durations of 1, 2, and 4 h.

Application of aircraft navigation sensors to enhanced vision systems

NASA Technical Reports Server (NTRS)

Sweet, Barbara T.

1993-01-01

In this presentation, the applicability of various aircraft navigation sensors to enhanced vision system design is discussed. First, the accuracy requirements of the FAA for precision landing systems are presented, followed by the current navigation systems and their characteristics. These systems include Instrument Landing System (ILS), Microwave Landing System (MLS), Inertial Navigation, Altimetry, and Global Positioning System (GPS). Finally, the use of navigation system data to improve enhanced vision systems is discussed. These applications include radar image rectification, motion compensation, and image registration.

Multiple operating system rotation environment moving target defense

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Nathaniel; Thompson, Michael

Systems and methods for providing a multiple operating system rotation environment ("MORE") moving target defense ("MTD") computing system are described. The MORE-MTD system provides enhanced computer system security through a rotation of multiple operating systems. The MORE-MTD system increases attacker uncertainty, increases the cost of attacking the system, reduces the likelihood of an attacker locating a vulnerability, and reduces the exposure time of any located vulnerability. The MORE-MTD environment is effectuated by rotation of the operating systems at a given interval. The rotating operating systems create a consistently changing attack surface for remote attackers.

Integrated nuclear data utilisation system for innovative reactors.

PubMed

Yamano, N; Hasegawa, A; Kato, K; Igashira, M

2005-01-01

A five-year research and development project on an integrated nuclear data utilisation system was initiated in 2002, for developing innovative nuclear energy systems such as accelerator-driven systems. The integrated nuclear data utilisation system will be constructed as a modular code system, which consists of two sub-systems: the nuclear data search and plotting sub-system, and the nuclear data processing and utilisation sub-system. The system will be operated with a graphical user interface in order to enable easy utilisation through the Internet by both nuclear design engineers and nuclear data evaluators. This paper presents an overview of the integrated nuclear data utilisation system, describes the development of a prototype system to examine the operability of the user interface and discusses specifications of the two sub-systems.

An expert system shell for inferring vegetation characteristics: Prototype help system (Task 1)

NASA Technical Reports Server (NTRS)

1993-01-01

The NASA Vegetation Workbench (VEG) is a knowledge based system that infers vegetation characteristics from reflectance data. A prototype of the VEG subgoal HELP.SYSTEM has been completed and the Help System has been added to the VEG system. It is loaded when the user first clicks on the HELP.SYSTEM option in the Tool Box Menu. The Help System provides a user tool to support needed user information. It also provides interactive tools the scientist may use to develop new help messages and to modify existing help messages that are attached to VEG screens. The system automatically manages system and file operations needed to preserve new or modified help messages. The Help System was tested both as a help system development and a help system user tool.

Two designs for an orbital transfer vehicle

NASA Technical Reports Server (NTRS)

Davis, Richard; Duquette, Miles; Fredrick, Rebecca; Schumacher, Daniel; Somers, Schaeffer; Stafira, Stanley; Williams, James; Zelinka, Mark

1988-01-01

The Orbital Transfer Vehicle (OTV) and systems were researched in the following areas: avionics, crew systems, electrical power systems, environmental control/life support systems, navigation and orbital maneuvers, propulsion systems, reaction control systems (RCS), servicing systems, and structures.

Conceptual design study: Forest Fire Advanced System Technology (FFAST)

NASA Technical Reports Server (NTRS)

Nichols, J. D.; Warren, J. R.

1986-01-01

An integrated forest fire detection and mapping system that will be based upon technology available in the 1990s was defined. Uncertainties in emerging and advanced technologies related to the conceptual design were identified and recommended for inclusion as preferred system components. System component technologies identified for an end-to-end system include thermal infrared, linear array detectors, automatic georeferencing and signal processing, geosynchronous satellite communication links, and advanced data integration and display. Potential system configuration options were developed and examined for possible inclusion in the preferred system configuration. The preferred system configuration will provide increased performance and be cost effective over the system currently in use. Forest fire management user requirements and the system component emerging technologies were the basis for the system configuration design. A preferred system configuration was defined that warrants continued refinement and development, examined economic aspects of the current and preferred system, and provided preliminary cost estimates for follow-on system prototype development.

Non-collinear valve actuator

NASA Technical Reports Server (NTRS)

Richard, James A. (Inventor)

2012-01-01

A non-collinear valve actuator includes a primary actuating system and a return spring system with each applying forces to a linkage system in order to regulate the flow of a quarter-turn valve. The primary actuating system and return spring system are positioned non-collinearly, which simply means the primary actuating system and return spring system are not in line with each other. By positioning the primary actuating system and return spring system in this manner, the primary actuating system can undergo a larger stroke while the return spring system experiences significantly less displacement. This allows the length of the return spring to be reduced due to the minimization of displacement thereby reducing the weight of the return spring system. By allowing the primary actuating system to undergo longer strokes, the weight of the primary actuating system may also be reduced. Accordingly, the weight of the non-collinear valve actuator is reduced.

Waste receiving and processing plant control system; system design description

DOE Office of Scientific and Technical Information (OSTI.GOV)

LANE, M.P.

1999-02-24

The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed asmore » separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1.« less

Lectures on algebraic system theory: Linear systems over rings

NASA Technical Reports Server (NTRS)

Kamen, E. W.

1978-01-01

The presentation centers on four classes of systems that can be treated as linear systems over a ring. These are: (1) discrete-time systems over a ring of scalars such as the integers; (2) continuous-time systems containing time delays; (3) large-scale discrete-time systems; and (4) time-varying discrete-time systems.

Method and apparatus for rate integration supplement for attitude referencing with quaternion differencing

NASA Technical Reports Server (NTRS)

Rodden, John James (Inventor); Price, Xenophon (Inventor); Carrou, Stephane (Inventor); Stevens, Homer Darling (Inventor)

2002-01-01

A control system for providing attitude control in spacecraft. The control system comprising a primary attitude reference system, a secondary attitude reference system, and a hyper-complex number differencing system. The hyper-complex number differencing system is connectable to the primary attitude reference system and the secondary attitude reference system.

Expert Systems: An Overview for Teacher-Librarians.

ERIC Educational Resources Information Center

Orwig, Gary; Barron, Ann

1992-01-01

Provides an overview of expert systems for teacher librarians. Highlights include artificial intelligence and expert systems; the development of the MYCIN medical expert system; rule-based expert systems; the use of expert system shells to develop a specific system; and how to select an appropriate application for an expert system. (11 references)…

MSFC Skylab Orbital Workshop, volume 2. [design and development of electrical systems and attitude control system

NASA Technical Reports Server (NTRS)

1974-01-01

The design and development of the Skylab Orbital Workshop are discussed. The subjects considered are: (1) thrust attitude control system, (2) solar array system, (3) electrical power distribution system, (4) communication and data acquisition system, (5) illumination system, and (6) caution and warning system.

21 CFR 866.5820 - Systemic lupus erythema-tosus immunological test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Systemic lupus erythema-tosus immunological test... Systems § 866.5820 Systemic lupus erythema-tosus immunological test system. (a) Identification. A systemic lupus erythematosus (SLE) immunological test system is a device that consists of the reagents used to...

Power System Information Delivering System Based on Distributed Object

NASA Astrophysics Data System (ADS)

Tanaka, Tatsuji; Tsuchiya, Takehiko; Tamura, Setsuo; Seki, Tomomichi; Kubota, Kenji

In recent years, improvement in computer performance and development of computer network technology or the distributed information processing technology has a remarkable thing. Moreover, the deregulation is starting and will be spreading in the electric power industry in Japan. Consequently, power suppliers are required to supply low cost power with high quality services to customers. Corresponding to these movements the authors have been proposed SCOPE (System Configuration Of PowEr control system) architecture for distributed EMS/SCADA (Energy Management Systems / Supervisory Control and Data Acquisition) system based on distributed object technology, which offers the flexibility and expandability adapting those movements. In this paper, the authors introduce a prototype of the power system information delivering system, which was developed based on SCOPE architecture. This paper describes the architecture and the evaluation results of this prototype system. The power system information delivering system supplies useful power systems information such as electric power failures to the customers using Internet and distributed object technology. This system is new type of SCADA system which monitors failure of power transmission system and power distribution system with geographic information integrated way.

On evolutionary systems.

PubMed

Alvarez de Lorenzana, J M; Ward, L M

1987-01-01

This paper develops a metatheoretical framework for understanding evolutionary systems (systems that develop in ways that increase their own variety). The framework addresses shortcomings seen in other popular systems theories. It concerns both living and nonliving systems, and proposes a metahierarchy of hierarchical systems. Thus, it potentially addresses systems at all descriptive levels. We restrict our definition of system to that of a core system whose parts have a different ontological status than the system, and characterize the core system in terms of five global properties: minimal length interval, minimal time interval, system cycle, total receptive capacity, and system potential. We propose two principles through the interaction of which evolutionary systems develop. The Principle of Combinatorial Expansion describes how a core system realizes its developmental potential through a process of progressive differentiation of the single primal state up to a limit stage. The Principle of Generative Condensation describes how the components of the last stage of combinatorial expansion condense and become the environment for and components of new, enriched systems. The early evolution of the Universe after the "big bang" is discussed in light of these ideas as an example of the application of the framework.

Transitioning to Integrated Modular Avionics with a Mission Management System

DTIC Science & Technology

2000-10-01

software structure, which is based on the use of a of interchangeable processing modules of a limited COTS Real - Time Operating System . number of...open standardised interfaces system hardware or the Real - Time Operating System directly supports the use of COTS components, which implementation, to...System RTOS Real - Time Operating System SMBP System Management Blueprint Interface SMOS System Management to Operating System Interface Figure 2: The ASAAC

Profiling Systems Using the Defining Characteristics of Systems of Systems (SoS)

DTIC Science & Technology

2010-02-01

system exhaust and emissions system gas engine heating and air conditioning system fuel system regenerative braking system safety system...overcome the limitations of these fuzzy scales, measurement scales are often divided into a relatively small number of disjoint categories so that the...precision is not justified. This lack of precision can typically be addressed by breaking the measurement scale into a set of categories , the use of

What factors affect the prices of low-priced U.S. solar PV systems?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemet, Gregory F.; O'Shaughnessy, Eric; Wiser, Ryan

The price of solar PV systems has declined rapidly, yet there are some much lower-priced systems than others. This study explores the factors that determine prices in these low-priced (LP) systems. Using a data set of 42,611 residential-scale PV systems installed in the U.S. in 2013, we use quantile regressions to estimate the importance of factors affecting the installed prices for LP systems (those at the 10th percentile) in comparison to median-priced systems. We find that the value of solar to consumers-a variable that accounts for subsidies, electric rates, and PV generation levels-is associated with lower prices for LP systemsmore » but higher prices for median priced systems. Conversely, systems installed in new home construction are associated with lower prices at the median but higher prices for LP. Other variables have larger price-reducing effects on LP than on median priced systems: systems installed in Arizona and Florida, as well as commercial and thin film systems. In contrast, the following have a smaller effect on prices for LP systems than median priced systems: tracking systems, self-installations, systems installed in Massachusetts, the system size, and installer experience. Furthermore, these results highlight the complex factors at play that lead to LP systems and shed light into how such LP systems can come about.« less

What factors affect the prices of low-priced U.S. solar PV systems?

DOE PAGES

Nemet, Gregory F.; O'Shaughnessy, Eric; Wiser, Ryan; ...

2017-08-09

The price of solar PV systems has declined rapidly, yet there are some much lower-priced systems than others. This study explores the factors that determine prices in these low-priced (LP) systems. Using a data set of 42,611 residential-scale PV systems installed in the U.S. in 2013, we use quantile regressions to estimate the importance of factors affecting the installed prices for LP systems (those at the 10th percentile) in comparison to median-priced systems. We find that the value of solar to consumers-a variable that accounts for subsidies, electric rates, and PV generation levels-is associated with lower prices for LP systemsmore » but higher prices for median priced systems. Conversely, systems installed in new home construction are associated with lower prices at the median but higher prices for LP. Other variables have larger price-reducing effects on LP than on median priced systems: systems installed in Arizona and Florida, as well as commercial and thin film systems. In contrast, the following have a smaller effect on prices for LP systems than median priced systems: tracking systems, self-installations, systems installed in Massachusetts, the system size, and installer experience. Furthermore, these results highlight the complex factors at play that lead to LP systems and shed light into how such LP systems can come about.« less

NASA Systems Engineering Research Consortium: Defining the Path to Elegance in Systems

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Farrington, Phillip A.

2016-01-01

The NASA Systems Engineering Research Consortium was formed at the end of 2010 to study the approaches to producing elegant systems on a consistent basis. This has been a transformative study looking at the engineering and organizational basis of systems engineering. The consortium has engaged in a variety of research topics to determine the path to elegant systems. In the second year of the consortium, a systems engineering framework emerged which structured the approach to systems engineering and guided our research. This led in the third year to set of systems engineering postulates that the consortium is continuing to refine. The consortium has conducted several research projects that have contributed significantly to the understanding of systems engineering. The consortium has surveyed the application of the NASA 17 systems engineering processes, explored the physics and statistics of systems integration, and considered organizational aspects of systems engineering discipline integration. The systems integration methods have included system exergy analysis, Akaike Information Criteria (AIC), State Variable Analysis, Multidisciplinary Coupling Analysis (MCA), Multidisciplinary Design Optimization (MDO), System Cost Modelling, System Robustness, and Value Modelling. Organizational studies have included the variability of processes in change evaluations, margin management within the organization, information theory of board structures, social categorization of unintended consequences, and initial looks at applying cognitive science to systems engineering. Consortium members have also studied the bidirectional influence of policy and law with systems engineering.

NASA Systems Engineering Research Consortium: Defining the Path to Elegance in Systems

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Farrington, Phillip A.

2016-01-01

The NASA Systems Engineering Research Consortium was formed at the end of 2010 to study the approaches to producing elegant systems on a consistent basis. This has been a transformative study looking at the engineering and organizational basis of systems engineering. The consortium has engaged in a variety of research topics to determine the path to elegant systems. In the second year of the consortium, a systems engineering framework emerged which structured the approach to systems engineering and guided our research. This led in the third year to set of systems engineering postulates that the consortium is continuing to refine. The consortium has conducted several research projects that have contributed significantly to the understanding of systems engineering. The consortium has surveyed the application of the NASA 17 systems engineering processes, explored the physics and statistics of systems integration, and considered organizational aspects of systems engineering discipline integration. The systems integration methods have included system energy analysis, Akaike Information Criteria (AIC), State Variable Analysis, Multidisciplinary Coupling Analysis (MCA), Multidisciplinary Design Optimization (MDO), System Cost Modeling, System Robustness, and Value Modeling. Organizational studies have included the variability of processes in change evaluations, margin management within the organization, information theory of board structures, social categorization of unintended consequences, and initial looks at applying cognitive science to systems engineering. Consortium members have also studied the bidirectional influence of policy and law with systems engineering.

Numerical Analysis of Combined Well and Open-Closed Loops Geothermal (CWG) Systems

NASA Astrophysics Data System (ADS)

Park, Yu-Chul

2016-04-01

Open-loop geothermal heat pump (GHP) system and closed-loop heat pump systems have been used in Korea to reduce emission of greenhouse gases such as carbon dioxide (CO2). The GHP systems have the pros and cons, for example, the open-loop GHP system is good energy-efficient and the closed-loop GHP system requires minimum maintenance costs. The open-loop GHP system can be used practically only with large amount of groundwater supply. The closed-loop GHP system can be used with high costs of initial installation. The performance and efficiency of the GHP system depend on the characteristics of the GHP system itself in addition to the geologic conditions. To overcome the cons of open-loop or closed-loop GHP system, the combined well and open-closed loops geothermal (CWG) system was designed. The open-loop GHP system is surrounded with closed-loop GHP systems in the CWG system. The geothermal energy in closed-loop GHP systems is supplied by the groundwater pumped by the open-loop GHP system. In this study, 2 different types of the CWG systems (small aperture hybrid CWG system and large aperture CWG system) are estimated using numerical simulation models in the aspect of energy efficiency. This work was supported by the New & Renewable Energy Core Technology Program of the Korea Institute of Energy Technology Evaluation and Planning (KETEP), granted financial resource from the Ministry of Trade, Industry & Energy, Republic of Korea. (No.20153030111120).

Potential risk for bacterial contamination in conventional reused ventilator systems and disposable closed ventilator-suction systems

PubMed Central

Li, Ya-Chi; Lin, Hui-Ling; Liao, Fang-Chun; Wang, Sing-Siang; Chang, Hsiu-Chu; Hsu, Hung-Fu; Chen, Sue-Hsien

2018-01-01

Background Few studies have investigated the difference in bacterial contamination between conventional reused ventilator systems and disposable closed ventilator-suction systems. The aim of this study was to investigate the bacterial contamination rates of the reused and disposable ventilator systems, and the association between system disconnection and bacterial contamination of ventilator systems. Methods The enrolled intubated and mechanically ventilated patients used a conventional reused ventilator system and a disposable closed ventilator-suction system, respectively, for a week; specimens were then collected from the ventilator circuit systems to evaluate human and environmental bacterial contamination. The sputum specimens from patients were also analyzed in this study. Results The detection rate of bacteria in the conventional reused ventilator system was substantially higher than that in the disposable ventilator system. The inspiratory and expiratory limbs of the disposable closed ventilator-suction system had higher bacterial concentrations than the conventional reused ventilator system. The bacterial concentration in the heated humidifier of the reused ventilator system was significantly higher than that in the disposable ventilator system. Positive associations existed among the bacterial concentrations at different locations in the reused and disposable ventilator systems, respectively. The predominant bacteria identified in the reused and disposable ventilator systems included Acinetobacter spp., Bacillus cereus, Elizabethkingia spp., Pseudomonas spp., and Stenotrophomonas (Xan) maltophilia. Conclusions Both the reused and disposable ventilator systems had high bacterial contamination rates after one week of use. Disconnection of the ventilator systems should be avoided during system operation to decrease the risks of environmental pollution and human exposure, especially for the disposable ventilator system. Trial registration ClinicalTrials.gov PRS / NCT03359148 PMID:29547638

A definition of high-level decisions in the engineering of systems

NASA Astrophysics Data System (ADS)

Powell, Robert Anthony

The role of the systems engineer defines that he or she be proactive and guide the program manager and their customers through their decisions to enhance the effectiveness of system development---producing faster, better, and cheaper systems. The present lack of coverage in literature on what these decisions are and how they relate to each other may be a contributing factor to the high rate of failure among system projects. At the onset of the system development process, decisions have an integral role in the design of a system that meets stakeholders' needs. This is apparent during the design and qualification of both the Development System and the Operational System. The performance, cost and schedule of the Development System affect the performance of the Operational System and are affected by decisions that influence physical elements of the Development System. The performance, cost, and schedule of the Operational System is affected by decisions that influence physical elements of the Operational System. Traditionally, product and process have been designed using know-how and trial and error. However, the empiricism of engineers and program managers is limited which can, and has led to costly mistakes. To date, very little research has explored decisions made in the engineering of a system. In government, literature exists on procurement processes for major system development; but in general literature on decisions, how they relate to each other, and the key information requirements within one of two systems and across the two systems is not readily available. This research hopes to improve the processes inherent in the engineering of systems. The primary focus of this research is on department of defense (DoD) military systems, specifically aerospace systems and may generalize more broadly. The result of this research is a process tool, a Decision System Model, which can be used by systems engineers to guide the program manager and their customers through the decisions about concurrently designing and qualifying both the Development and Operational systems.

CARRIER/CASK HANDLING SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

E.F. Loros

2000-06-23

The Carrier/Cask Handling System receives casks on railcars and legal-weight trucks (LWTs) (transporters) that transport loaded casks and empty overpacks to the Monitored Geologic Repository (MGR) from the Carrier/Cask Transport System. Casks that come to the MGR on heavy-haul trucks (HHTs) are transferred onto railcars before being brought into the Carrier/Cask Handling System. The system is the interfacing system between the railcars and LWTs and the Assembly Transfer System (ATS) and Canister Transfer System (CTS). The Carrier/Cask Handling System removes loaded casks from the cask transporters and transfers the casks to a transfer cart for either the ATS or CTS,more » as appropriate, based on cask contents. The Carrier/Cask Handling System receives the returned empty casks from the ATS and CTS and mounts the casks back onto the transporters for reshipment. If necessary, the Carrier/Cask Handling System can also mount loaded casks back onto the transporters and remove empty casks from the transporters. The Carrier/Cask Handling System receives overpacks from the ATS loaded with canisters that have been cut open and emptied and mounts the overpacks back onto the transporters for disposal. If necessary, the Carrier/Cask Handling System can also mount empty overpacks back onto the transporters and remove loaded overpacks from them. The Carrier/Cask Handling System is located within the Carrier Bay of the Waste Handling Building System. The system consists of cranes, hoists, manipulators, and supporting equipment. The Carrier/Cask Handling System is designed with the tooling and fixtures necessary for handling a variety of casks. The Carrier/Cask Handling System performance and reliability are sufficient to support the shipping and emplacement schedules for the MGR. The Carrier/Cask Handling System interfaces with the Carrier/Cask Transport System, ATS, and CTS as noted above. The Carrier/Cask Handling System interfaces with the Waste Handling Building System for building structures and space allocations. The Carrier/Cask Handling System interfaces with the Waste Handling Building Electrical System for electrical power.« less

Comparing administered and market-based water allocation systems using an agent-based modeling approach

NASA Astrophysics Data System (ADS)

Zhao, J.; Cai, X.; Wang, Z.

2009-12-01

It also has been well recognized that market-based systems can have significant advantages over administered systems for water allocation. However there are not many successful water markets around the world yet and administered systems exist commonly in water allocation management practice. This paradox has been under discussion for decades and still calls for attention for both research and practice. This paper explores some insights for the paradox and tries to address why market systems have not been widely implemented for water allocation. Adopting the theory of agent-based system we develop a consistent analytical model to interpret both systems. First we derive some theorems based on the analytical model, with respect to the necessary conditions for economic efficiency of water allocation. Following that the agent-based model is used to illustrate the coherence and difference between administered and market-based systems. The two systems are compared from three aspects: 1) the driving forces acting on the system state, 2) system efficiency, and 3) equity. Regarding economic efficiency, penalty on the violation of water use permits (or rights) under an administered system can lead to system-wide economic efficiency, as well as being acceptable by some agents, which follows the theory of the so-call rational violation. Ideal equity will be realized if penalty equals incentive with an administered system and if transaction costs are zero with a market system. The performances of both agents and the over system are explained with an administered system and market system, respectively. The performances of agents are subject to different mechanisms of interactions between agents under the two systems. The system emergency (i.e., system benefit, equilibrium market price, etc), resulting from the performance at the agent level, reflects the different mechanism of the two systems, the “invisible hand” with the market system and administrative measures (penalty and subsidy) with the administered system. Furthermore, the impact of hydrological uncertainty on the performance of water users under the two systems is analyzed by extending the deterministic model to a stochastic one subject to the uncertainty of water availability. It is found that the system response to hydrologic uncertainty depends on risk management mechanics - sharing risk equally among the agents or by prescribed priorities on some agents. Figure1. Agent formulation and its implications in administered system and market-based system

40 CFR 60.287a - Recordkeeping.

Code of Federal Regulations, 2014 CFR

2014-07-01

... furnace, digester system, brown stock washer system, multiple-effect evaporator system, or condensate... digester system, brown stock washer system, multiple effect evaporator system, or condensate stripper...

Clicker Implementation Models

ERIC Educational Resources Information Center

White, Peter J. T.; Delaney, David G.; Syncox, David; Akerberg, Oscar Avila; Alters, Brian

2011-01-01

Student response systems can help instructors integrate active learning into their classrooms. Such technology is known by a variety of names, including classroom response systems, student response systems, audience response systems, electronic response systems, personal response systems, zappers, and clickers. The "system" consists of three…

Evaluation of weigh-in-motion systems.

DOT National Transportation Integrated Search

1991-01-01

The objective of this research was to evaluate low cost weigh-in-motion systems. The three systems evaluated were (1) a capacitance weigh mat system, (2) a bridge weighing system, and (3) a piezoelectric cable sensor system. All three systems have a ...

Prognostic Analysis System and Methods of Operation

NASA Technical Reports Server (NTRS)

MacKey, Ryan M. E. (Inventor); Sneddon, Robert (Inventor)

2014-01-01

A prognostic analysis system and methods of operating the system are provided. In particular, a prognostic analysis system for the analysis of physical system health applicable to mechanical, electrical, chemical and optical systems and methods of operating the system are described herein.

Quality monitored distributed voting system

DOEpatents

Skogmo, David

1997-01-01

A quality monitoring system can detect certain system faults and fraud attempts in a distributed voting system. The system uses decoy voters to cast predetermined check ballots. Absent check ballots can indicate system faults. Altered check ballots can indicate attempts at counterfeiting votes. The system can also cast check ballots at predetermined times to provide another check on the distributed voting system.

The Kritzel System for handwriting interpretation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qian, G.

We present a new system for recognizing on-line cursive handwriting. The system, which is called the Kritzel System, has four features. First, the system characterizes handwriting as a sequence of feature vectors. Second, the system adapts to a particular writing style itself through a learning process. Third, the reasoning of the system is formulated in propositional logic with likelihoods. Fourth, the system can be readily linked with other English processing systems for lexical and contextual checking.

Systems and methods for an integrated electrical sub-system powered by wind energy

DOEpatents

Liu, Yan [Ballston Lake, NY; Garces, Luis Jose [Niskayuna, NY

2008-06-24

Various embodiments relate to systems and methods related to an integrated electrically-powered sub-system and wind power system including a wind power source, an electrically-powered sub-system coupled to and at least partially powered by the wind power source, the electrically-powered sub-system being coupled to the wind power source through power converters, and a supervisory controller coupled to the wind power source and the electrically-powered sub-system to monitor and manage the integrated electrically-powered sub-system and wind power system.

Design and realization of tourism spatial decision support system based on GIS

NASA Astrophysics Data System (ADS)

Ma, Zhangbao; Qi, Qingwen; Xu, Li

2008-10-01

In this paper, the existing problems of current tourism management information system are analyzed. GIS, tourism as well as spatial decision support system are introduced, and the application of geographic information system technology and spatial decision support system to tourism management and the establishment of tourism spatial decision support system based on GIS are proposed. System total structure, system hardware and software environment, database design and structure module design of this system are introduced. Finally, realization methods of this systemic core functions are elaborated.

Artificial intelligence and space power systems automation

NASA Technical Reports Server (NTRS)

Weeks, David J.

1987-01-01

Various applications of artificial intelligence to space electrical power systems are discussed. An overview is given of completed, on-going, and planned knowledge-based system activities. These applications include the Nickel-Cadmium Battery Expert System (NICBES) (the expert system interfaced with the Hubble Space Telescope electrical power system test bed); the early work with the Space Station Experiment Scheduler (SSES); the three expert systems under development in the space station advanced development effort in the core module power management and distribution system test bed; planned cooperation of expert systems in the Core Module Power Management and Distribution (CM/PMAD) system breadboard with expert systems for the space station at other research centers; and the intelligent data reduction expert system under development.

Systems and Methods for Derivative-Free Adaptive Control

NASA Technical Reports Server (NTRS)

Calise, Anthony J. (Inventor); Yucelen, Tansel (Inventor); Kim, Kilsoo (Inventor)

2015-01-01

An adaptive control system is disclosed. The control system can control uncertain dynamic systems. The control system can employ one or more derivative-free adaptive control architectures. The control system can further employ one or more derivative-free weight update laws. The derivative-free weight update laws can comprise a time-varying estimate of an ideal vector of weights. The control system of the present invention can therefore quickly stabilize systems that undergo sudden changes in dynamics, caused by, for example, sudden changes in weight. Embodiments of the present invention can also provide a less complex control system than existing adaptive control systems. The control system can control aircraft and other dynamic systems, such as, for example, those with non-minimum phase dynamics.

MINIS: Multipurpose Interactive NASA Information System

NASA Technical Reports Server (NTRS)

1976-01-01

The Multipurpose Interactive NASA Information Systems (MINIS) was developed in response to the need for a data management system capable of operation on several different minicomputer systems. The desired system had to be capable of performing the functions of a LANDSAT photo descriptive data retrieval system while remaining general in terms of other acceptable user definable data bases. The system also had to be capable of performing data base updates and providing user-formatted output reports. The resultant MINI System provides all of these capabilities and several other features to complement the data management system. The MINI System is currently implemented on two minicomputer systems and is in the process of being installed on another minicomputer system. The MINIS is operational on four different data bases.

Boundary-fitted coordinate systems for numerical solution of partial differential equations - A review

NASA Technical Reports Server (NTRS)

Thompson, J. F.; Warsi, Z. U. A.; Mastin, C. W.

1982-01-01

A comprehensive review of methods of numerically generating curvilinear coordinate systems with coordinate lines coincident with all boundary segments is given. Some general mathematical framework and error analysis common to such coordinate systems is also included. The general categories of generating systems are those based on conformal mapping, orthogonal systems, nearly orthogonal systems, systems produced as the solution of elliptic and hyperbolic partial differential equations, and systems generated algebraically by interpolation among the boundaries. Also covered are the control of coordinate line spacing by functions embedded in the partial differential operators of the generating system and by subsequent stretching transformation. Dynamically adaptive coordinate systems, coupled with the physical solution, and time-dependent systems that follow moving boundaries are treated. References reporting experience using such coordinate systems are reviewed as well as those covering the system development.

LDEF systems special investigation group overview

NASA Technical Reports Server (NTRS)

Mason, Jim; Dursch, Harry

1995-01-01

The Systems Special Investigation Group (Systems SIG), formed by the LDEF Project Office to perform post-flight analysis of LDEF systems hardware, was chartered to investigate the effects of the extended LDEF mission on both satellite and experiment systems and to coordinate and integrate all systems related analyses performed during post-flight investigations. The Systems SIG published a summary report in April, 1992 titled 'Analysis of Systems Hardware Flown on LDEF - Results of the Systems Special Investigation Group' that described findings through the end of 1991. The Systems SIG, unfunded in FY 92 and FY93, has been funded in FY 94 to update this report with all new systems related findings. This paper provides a brief summary of the highlights of earlier Systems SIG accomplishments and describes tasks the Systems SIG has been funded to accomplish in FY 94.

Dilution cycle control for an absorption refrigeration system

DOEpatents

Reimann, Robert C.

1984-01-01

A dilution cycle control system for an absorption refrigeration system is disclosed. The control system includes a time delay relay for sensing shutdown of the absorption refrigeration system and for generating a control signal only after expiration of a preselected time period measured from the sensed shutdown of the absorption refrigeration system, during which the absorption refrigeration system is not restarted. A dilution cycle for the absorption refrigeration system is initiated in response to generation of a control signal by the time delay relay. This control system is particularly suitable for use with an absorption refrigeration system which is frequently cycled on and off since the time delay provided by the control system prevents needless dilution of the absorption refrigeration system when the system is turned off for only a short period of time and then is turned back on.

Project Management Using Modern Guidance, Navigation and Control Theory

NASA Technical Reports Server (NTRS)

Hill, Terry

2010-01-01

The idea of control theory and its application to project management is not new, however literature on the topic and real-world applications is not as readily available and comprehensive in how all the principals of Guidance, Navigation and Control (GN&C) apply. This paper will address how the fundamental principals of modern GN&C Theory have been applied to NASA's Constellation Space Suit project and the results in the ability to manage the project within cost, schedule and budget. A s with physical systems, projects can be modeled and managed with the same guiding principles of GN&C as if it were a complex vehicle, system or software with time-varying processes, at times non-linear responses, multiple data inputs of varying accuracy and a range of operating points. With such systems the classic approach could be applied to small and well-defined projects; however with larger, multi-year projects involving multiple organizational structures, external influences and a multitude of diverse resources, then modern control theory is required to model and control the project. The fundamental principals of G N&C stated that a system is comprised of these basic core concepts: State, Behavior, Control system, Navigation system, Guidance and Planning Logic, Feedback systems. The state of a system is a definition of the aspects of the dynamics of the system that can change, such as position, velocity, acceleration, coordinate-based attitude, temperature, etc. The behavior of the system is more of what changes are possible rather than what can change, which is captured in the state of the system. The behavior of a system is captured in the system modeling and if properly done, will aid in accurate system performance prediction in the future. The Control system understands the state and behavior of the system and feedback systems to adjust the control inputs into the system. The Navigation system takes the multiple data inputs and based upon a priori knowledge of the input, will develop a statistical-based weighting of the input to determine where the system currently is located. Guidance and Planning logic of the system with the understanding of where it is (provided by the navigation system) will in turn determine where it needs to be and how to get there. Lastly, the system Feedback system is the right arm of the control system to allow it to affect change in the overall system and therefore it is critical to not only correctly identify the system feedback inputs but also the system response to the feedback inputs. And with any systems project it is critical that the objective of the system be clearly defined for not only planning but to be used to measure performance and to aid in the guidance of the system or project.

Integrating system safety into the basic systems engineering process

NASA Technical Reports Server (NTRS)

Griswold, J. W.

1971-01-01

The basic elements of a systems engineering process are given along with a detailed description of what the safety system requires from the systems engineering process. Also discussed is the safety that the system provides to other subfunctions of systems engineering.

High Maturity Is Not a Procrustean Bed

DTIC Science & Technology

2014-07-01

older legacy system or set of systems Brownfield modernization Incremental replacement of old, fragile business systems with COTS products or...platform • Family of systems or product line • System of systems (SoS) or enterprise-wide system • Brownfield modernization Table 2 briefly

Architecture Analysis of Evolving Complex Systems of Systems: Technical Presentation [and Executive Status Report

NASA Technical Reports Server (NTRS)

Lindvall, Mikael; Godfrey, Sally; Ackermann, Chris; Ray, Arnab; Yonkwa, Lyly; Ganesan, Dharma; Stratton, William C.; Sibol, Deane E.

2008-01-01

Analyze, Visualize, and Evaluate structure and behavior using static and dynamic information, individual systems as well as systems of systems. Next steps: Refine software tool support; Apply to other systems; and Apply earlier in system life cycle.

Lot-to-Lot Variability of Test Strips and Accuracy Assessment of Systems for Self-Monitoring of Blood Glucose according to ISO 15197

PubMed Central

Baumstark, Annette; Pleus, Stefan; Schmid, Christina; Link, Manuela; Haug, Cornelia; Freckmann, Guido

2012-01-01

Background Accurate and reliable blood glucose (BG) measurements require that different test strip lots of the same BG monitoring system provide comparable measurement results. Only a small number of studies addressing this question have been published. Methods In this study, four test strip lots for each of five different BG systems [Accu-Chek® Aviva (system A), FreeStyle Lite® (system B), GlucoCheck XL (system C), Pura™/mylife™ Pura (system D), and OneTouch® Verio™ Pro (system E)] were evaluated with procedures according to DIN EN ISO 15197:2003. The BG system measurement results were compared with the manufacturer’s measurement procedure (glucose oxidase or hexokinase method). Relative bias according to Bland and Altman and system accuracy according to ISO 15197 were analyzed. A BG system consists of the BG meter itself and the test strips. Results The maximum lot-to-lot difference between any two of the four evaluated test strip lots per BG system was 1.0% for system E, 2.1% for system A, 3.1% for system C, 6.9% for system B, and 13.0% for system D. Only two systems (systems A and B) fulfill the criteria of DIN EN ISO 15197:2003 with each test strip lot. Conclusions Considerable lot-to-lot variability between test strip lots of the same BG system was found. These variations add to other sources of inaccuracy with the specific BG system. Manufacturers should regularly and effectively check the accuracy of their BG meters and test strips even between different test strip lots to minimize risk of false treatment decisions. PMID:23063033

Reactive system verification case study: Fault-tolerant transputer communication

NASA Technical Reports Server (NTRS)

Crane, D. Francis; Hamory, Philip J.

1993-01-01

A reactive program is one which engages in an ongoing interaction with its environment. A system which is controlled by an embedded reactive program is called a reactive system. Examples of reactive systems are aircraft flight management systems, bank automatic teller machine (ATM) networks, airline reservation systems, and computer operating systems. Reactive systems are often naturally modeled (for logical design purposes) as a composition of autonomous processes which progress concurrently and which communicate to share information and/or to coordinate activities. Formal (i.e., mathematical) frameworks for system verification are tools used to increase the users' confidence that a system design satisfies its specification. A framework for reactive system verification includes formal languages for system modeling and for behavior specification and decision procedures and/or proof-systems for verifying that the system model satisfies the system specifications. Using the Ostroff framework for reactive system verification, an approach to achieving fault-tolerant communication between transputers was shown to be effective. The key components of the design, the decoupler processes, may be viewed as discrete-event-controllers introduced to constrain system behavior such that system specifications are satisfied. The Ostroff framework was also effective. The expressiveness of the modeling language permitted construction of a faithful model of the transputer network. The relevant specifications were readily expressed in the specification language. The set of decision procedures provided was adequate to verify the specifications of interest. The need for improved support for system behavior visualization is emphasized.

Preliminary design package for solar heating and hot water system

NASA Technical Reports Server (NTRS)

1977-01-01

The preliminary design review on the development of two prototype solar heating and hot water systems is presented. The information contained in this report includes system certification, system functional description, system configuration, system specification, system performance and other documents pertaining to the progress and the design of the system. This system, which is intended for use in the normal single-family residence, consists of the following subsystems: collector, storage, control, transport, and Government-furnished Site Data Acquisition.

Earth orbit navigation study. Volume 2: System evaluation

NASA Technical Reports Server (NTRS)

1972-01-01

An overall systems evaluation was made of five candidate navigation systems in support of earth orbit missions. The five systems were horizon sensor system, unkown landmark tracking system, ground transponder system, manned space flight network, and tracking and data relay satellite system. Two reference missions were chosen: a low earth orbit mission and a transfer trajectory mission from low earth orbit to geosynchronous orbit. The specific areas addressed in the evaluation were performance, multifunction utilization, system mechanization, and cost.

F18 Life Support: APECS and EDOX Cockpit Integration

NASA Technical Reports Server (NTRS)

Herrick, Paul

1998-01-01

Two systems are currently being integrated into the F18 Hornet support aircraft at NASA Dryden Flight Research Center (DFRC). The first system is the Aircrew Personal Environmental Control System (APECS). The system is designed to increase aircrew performance by combating heat stress in the cockpit. The second system is the Extended Duration Oxygen System (EDOX). This system will provide additional redundancy and oxygen system duration to the F18 without extensive modification to the current system.

Lightside Atmospheric Revitalization System

NASA Technical Reports Server (NTRS)

Colling, A. K.; Cushman, R. J.; Hultman, M. M.; Nason, J. R.

1980-01-01

The system was studied as a replacement to the present baseline LiOH system for extended duration shuttle missions. The system consists of three subsystems: a solid amine water desorbed regenerable carbon dioxide removal system, a water vapor electrolysis oxygen generating system, and a Sabatier reactor carbon dioxide reduction system. The system is designed for use on a solar powered shuttle vehicle. The majority of the system's power requirements are utilized on the Sun side of each orbit, when solar power is available.

Status of the JWST Science Instrument Payload

NASA Technical Reports Server (NTRS)

Greenhouse, Matt

2016-01-01

The James Webb Space Telescope (JWST) Integrated Science Instrument Module (ISIM) system consists of five sensors (4 science): Mid-Infrared Instrument (MIRI), Near Infrared Imager and Slitless Spectrograph (NIRISS), Fine Guidance Sensor (FGS), Near InfraRed Camera (NIRCam), Near InfraRed Spectrograph (NIRSpec); and nine instrument support systems: Optical metering structure system, Electrical Harness System; Harness Radiator System, ISIM Electronics Compartment, ISIM Remote Services Unit, Cryogenic Thermal Control System, Command and Data Handling System, Flight Software System, Operations Scripts System.

System of Systems Engineering and Integration Process for Network Transport Assessment

DTIC Science & Technology

2016-09-01

SOSE&I CONCEPTS The DOD-sourced “Systems Engineering Guide for Systems of Systems” provides an overview of the SoS environment and SE considerations...usage as a guide in application of systems engineering processes. They are listed verbatim below as defined in the DOD SE guide (ODUSD[A&T]SSE 2008...Technology (A&T), Systems and Software Engineering (SSE). 2008. Systems Engineering Guide for Systems of Systems. Washington, DC: ODUSD(A&T)SSE

Advanced controls for light sources

NASA Astrophysics Data System (ADS)

Biedron, S. G.; Edelen, A. L.; Milton, S. V.

2016-09-01

We present a summary of our team's recent efforts in developing adaptive, artificial intelligence-inspired techniques specifically to address several control challenges that arise in machines/systems including those in particle accelerator systems. These techniques can readily be adapted to other systems such as lasers, beamline optics, etc… We are not at all suggesting that we create an autonomous system, but create a system with an intelligent control system, that can continually use operational data to improve itself and combines both traditional and advanced techniques. We believe that the system performance and reliability can be increased based on our findings. Another related point is that the controls sub-system of an overall system is usually not the heart of the system architecture or design process. More bluntly, often times all of the peripheral systems are considered as secondary to the main system components in the architecture design process because it is assumed that the controls system will be able to "fix" challenges found later with the sub-systems for overall system operation. We will show that this is not always the case and that it took an intelligent control application to overcome a sub-system's challenges. We will provide a recent example of such a "fix" with a standard controller and with an artificial intelligence-inspired controller. A final related point to be covered is that of system adaptation for requirements not original to a system's original design.

Systems and methods for circuit lifetime evaluation

NASA Technical Reports Server (NTRS)

Heaps, Timothy L. (Inventor); Sheldon, Douglas J. (Inventor); Bowerman, Paul N. (Inventor); Everline, Chester J. (Inventor); Shalom, Eddy (Inventor); Rasmussen, Robert D. (Inventor)

2013-01-01

Systems and methods for estimating the lifetime of an electrical system in accordance with embodiments of the invention are disclosed. One embodiment of the invention includes iteratively performing Worst Case Analysis (WCA) on a system design with respect to different system lifetimes using a computer to determine the lifetime at which the worst case performance of the system indicates the system will pass with zero margin or fail within a predetermined margin for error given the environment experienced by the system during its lifetime. In addition, performing WCA on a system with respect to a specific system lifetime includes identifying subcircuits within the system, performing Extreme Value Analysis (EVA) with respect to each subcircuit to determine whether the subcircuit fails EVA for the specific system lifetime, when the subcircuit passes EVA, determining that the subcircuit does not fail WCA for the specified system lifetime, when a subcircuit fails EVA performing at least one additional WCA process that provides a tighter bound on the WCA than EVA to determine whether the subcircuit fails WCA for the specified system lifetime, determining that the system passes WCA with respect to the specific system lifetime when all subcircuits pass WCA, and determining that the system fails WCA when at least one subcircuit fails WCA.

A review of human factors challenges of complex adaptive systems: discovering and understanding chaos in human performance.

PubMed

Karwowski, Waldemar

2012-12-01

In this paper, the author explores a need for a greater understanding of the true nature of human-system interactions from the perspective of the theory of complex adaptive systems, including the essence of complexity, emergent properties of system behavior, nonlinear systems dynamics, and deterministic chaos. Human performance, more often than not, constitutes complex adaptive phenomena with emergent properties that exhibit nonlinear dynamical (chaotic) behaviors. The complexity challenges in the design and management of contemporary work systems, including service systems, are explored. Examples of selected applications of the concepts of nonlinear dynamics to the study of human physical performance are provided. Understanding and applications of the concepts of theory of complex adaptive and dynamical systems should significantly improve the effectiveness of human-centered design efforts of a large system of systems. Performance of many contemporary work systems and environments may be sensitive to the initial conditions and may exhibit dynamic nonlinear properties and chaotic system behaviors. Human-centered design of emergent human-system interactions requires application of the theories of nonlinear dynamics and complex adaptive system. The success of future human-systems integration efforts requires the fusion of paradigms, knowledge, design principles, and methodologies of human factors and ergonomics with those of the science of complex adaptive systems as well as modern systems engineering.

Solar Dynamic Power System Stability Analysis and Control

NASA Technical Reports Server (NTRS)

Momoh, James A.; Wang, Yanchun

1996-01-01

The objective of this research is to conduct dynamic analysis, control design, and control performance test of solar power system. Solar power system consists of generation system and distribution network system. A bench mark system is used in this research, which includes a generator with excitation system and governor, an ac/dc converter, six DDCU's and forty-eight loads. A detailed model is used for modeling generator. Excitation system is represented by a third order model. DDCU is represented by a seventh order system. The load is modeled by the combination of constant power and constant impedance. Eigen-analysis and eigen-sensitivity analysis are used for system dynamic analysis. The effects of excitation system, governor, ac/dc converter control, and the type of load on system stability are discussed. In order to improve system transient stability, nonlinear ac/dc converter control is introduced. The direct linearization method is used for control design. The dynamic analysis results show that these controls affect system stability in different ways. The parameter coordination of controllers are recommended based on the dynamic analysis. It is concluded from the present studies that system stability is improved by the coordination of control parameters and the nonlinear ac/dc converter control stabilize system oscillation caused by the load change and system fault efficiently.

Combination Chemotherapy in Treating Young Patients With Advanced Solid Tumors

ClinicalTrials.gov

2013-05-01

Childhood Central Nervous System Choriocarcinoma; Childhood Central Nervous System Embryonal Tumor; Childhood Central Nervous System Germ Cell Tumor; Childhood Central Nervous System Germinoma; Childhood Central Nervous System Mixed Germ Cell Tumor; Childhood Central Nervous System Teratoma; Childhood Central Nervous System Yolk Sac Tumor; Recurrent Childhood Brain Stem Glioma; Recurrent Childhood Central Nervous System Embryonal Tumor; Unspecified Childhood Solid Tumor, Protocol Specific

The Box and the Circle--Two Systems of Life: A Model for Understanding Native-Non-Native Issues.

ERIC Educational Resources Information Center

Derrick, Jann

Working as a family systems therapist with Native and non-Native families, the author observed two opposing social systems. Non-native families systems typify "The Box System," whereas native family systems portray "The Circle System." A few characteristics of the Circle System are: (1) a focus on life and peacefulness; (2) females and children…

Quality monitored distributed voting system

DOEpatents

Skogmo, D.

1997-03-18

A quality monitoring system can detect certain system faults and fraud attempts in a distributed voting system. The system uses decoy voters to cast predetermined check ballots. Absent check ballots can indicate system faults. Altered check ballots can indicate attempts at counterfeiting votes. The system can also cast check ballots at predetermined times to provide another check on the distributed voting system. 6 figs.

Development of U-Mart System with Plural Brands and Plural Markets

NASA Astrophysics Data System (ADS)

Akimoto, Yoshihito; Mori, Naoki; Ono, Isao; Nakajima, Yoshihiro; Kita, Hajime; Matsumoto, Keinosuke

In this paper, we first discuss the notion that artificial market systems should meet the requirements of fidelity, transparency, reproducibility, and traceability. Next, we introduce history of development of the artificial market system named U-Mart system that meet the requirements well, which have been developed by the U-Mart project. We have already developed the U-Mart system called “U-Mart system version 3.0” to solve problems of old U-Mart systems. In version 3.0 system, trading process is modularized and universal market system can be easily introduced.
However, U-Mart system version 3.0 only simulates the single brand futures market. The simulation of the plural brands and plural markets has been required by lot of users. In this paper, we proposed a novel U-Mart system called “U-Mart system version 4.0” to solve this problem of U-Mart system version 3.0. We improve the server system, machine agents and GUI in order to simulate plural brands and plural markets in U-Mart system version 4.0. The effectiveness of the proposed system is confirmed by statistical analysis of results of spot market simulation with random agents.

Feature-based component model for design of embedded systems

NASA Astrophysics Data System (ADS)

Zha, Xuan Fang; Sriram, Ram D.

2004-11-01

An embedded system is a hybrid of hardware and software, which combines software's flexibility and hardware real-time performance. Embedded systems can be considered as assemblies of hardware and software components. An Open Embedded System Model (OESM) is currently being developed at NIST to provide a standard representation and exchange protocol for embedded systems and system-level design, simulation, and testing information. This paper proposes an approach to representing an embedded system feature-based model in OESM, i.e., Open Embedded System Feature Model (OESFM), addressing models of embedded system artifacts, embedded system components, embedded system features, and embedded system configuration/assembly. The approach provides an object-oriented UML (Unified Modeling Language) representation for the embedded system feature model and defines an extension to the NIST Core Product Model. The model provides a feature-based component framework allowing the designer to develop a virtual embedded system prototype through assembling virtual components. The framework not only provides a formal precise model of the embedded system prototype but also offers the possibility of designing variation of prototypes whose members are derived by changing certain virtual components with different features. A case study example is discussed to illustrate the embedded system model.

Practical homeostasis lighting control system using sensor agent robots for office space

NASA Astrophysics Data System (ADS)

Tokiwa, Momoko; Mita, Akira

2014-03-01

The comfortable space can be changed by season, age, physical condition and the like. However, the current systems are not able to resolve them absolutely. This research proposes the Homeostasis lighting control system based on the mechanism of biotic homeostasis for making the algorithms of apparatus control. Homeostasis are kept by the interaction of the three systems, endocrine system, immune system, and nervous system[1]. By the gradual reaction in the endocrine system, body's protective response in the immune system, and the electrical reaction in the nerve system, we can keep the environments against variable changes. The new lighting control system utilizes this mechanism. Firstly, we focused on legibility and comfort in the office space to construct the control model learning from the endocrine and immune systems. The mechanism of the endocrine system is used for ambient lights in the space is used considering circadian rhythm for comfort. For the legibility, the immune system is used to control considering devices near the human depending on the distance between the human. Simulations and the demonstration were conducted to show the feasibility. Finally, the nerve system was intruded to enhance the system.

Designing and assessing a sustainable networked delivery (SND) system: hybrid business-to-consumer book delivery case study.

PubMed

Kim, Junbeum; Xu, Ming; Kahhat, Ramzy; Allenby, Braden; Williams, Eric

2009-01-01

We attempted to design and assess an example of a sustainable networked delivery (SND) system: a hybrid business-to-consumer book delivery system. This system is intended to reduce costs, achieve significant reductions in energy consumption, and reduce environmental emissions of critical local pollutants and greenhouse gases. The energy consumption and concomitant emissions of this delivery system compared with existing alternative delivery systems were estimated. We found that regarding energy consumption, an emerging hybrid delivery system which is a sustainable networked delivery system (SND) would consume 47 and 7 times less than the traditional networked delivery system (TND) and e-commerce networked delivery system (END). Regarding concomitant emissions, in the case of CO2, the SND system produced 32 and 7 times fewer emissions than the TND and END systems. Also the SND system offer meaningful economic benefit such as the costs of delivery and packaging, to the online retailer, grocery, and consumer. Our research results show that the SND system has a lot of possibilities to save local transportation energy consumption and delivery costs, and reduce environmental emissions in delivery system.

Open systems storage platforms

NASA Technical Reports Server (NTRS)

Collins, Kirby

1992-01-01

The building blocks for an open storage system includes a system platform, a selection of storage devices and interfaces, system software, and storage applications CONVEX storage systems are based on the DS Series Data Server systems. These systems are a variant of the C3200 supercomputer with expanded I/O capabilities. These systems support a variety of medium and high speed interfaces to networks and peripherals. System software is provided in the form of ConvexOS, a POSIX compliant derivative of 4.3BSD UNIX. Storage applications include products such as UNITREE and EMASS. With the DS Series of storage systems, Convex has developed a set of products which provide open system solutions for storage management applications. The systems are highly modular, assembled from off the shelf components with industry standard interfaces. The C Series system architecture provides a stable base, with the performance and reliability of a general purpose platform. This combination of a proven system architecture with a variety of choices in peripherals and application software allows wide flexibility in configurations, and delivers the benefits of open systems to the mass storage world.

An Integrative Theory of Psychotherapy: Research and Practice

PubMed Central

Epstein, Seymour; Epstein, Martha L.

2016-01-01

A dual-process personality theory and supporting research are presented. The dual processes comprise an experiential system and a rational system. The experiential system is an adaptive, associative learning system that humans share with other higher-order animals. The rational system is a uniquely human, primarily verbal, reasoning system. It is assumed that when humans developed language they did not abandon their previous ways of adapting, they simply added language to their experiential system. The two systems are assumed to operate in parallel and are bi-directionally interactive. The validity of these assumptions is supported by extensive research. Of particular relevance for psychotherapy, the experiential system, which is compatible with evolutionary theory, replaces the Freudian maladaptive unconscious system that is indefensible from an evolutionary perspective, as sub-human animals would then have only a single system that is maladaptive. The aim of psychotherapy is to produce constructive changes in the experiential system. Changes in the rational system are useful only to the extent that they contribute to constructive changes in the experiential system. PMID:27672302

An Integrative Theory of Psychotherapy: Research and Practice.

PubMed

Epstein, Seymour; Epstein, Martha L

2016-06-01

A dual-process personality theory and supporting research are presented. The dual processes comprise an experiential system and a rational system. The experiential system is an adaptive, associative learning system that humans share with other higher-order animals. The rational system is a uniquely human, primarily verbal, reasoning system. It is assumed that when humans developed language they did not abandon their previous ways of adapting, they simply added language to their experiential system. The two systems are assumed to operate in parallel and are bi-directionally interactive. The validity of these assumptions is supported by extensive research. Of particular relevance for psychotherapy, the experiential system, which is compatible with evolutionary theory, replaces the Freudian maladaptive unconscious system that is indefensible from an evolutionary perspective, as sub-human animals would then have only a single system that is maladaptive. The aim of psychotherapy is to produce constructive changes in the experiential system. Changes in the rational system are useful only to the extent that they contribute to constructive changes in the experiential system.

PV system field experience and reliability

NASA Astrophysics Data System (ADS)

Durand, Steven; Rosenthal, Andrew; Thomas, Mike

1997-02-01

Hybrid power systems consisting of battery inverters coupled with diesel, propane, or gasoline engine-driven electrical generators, and photovoltaic arrays are being used in many remote locations. The potential cost advantages of hybrid systems over simple engine-driven generator systems are causing hybrid systems to be considered for numerous applications including single-family residential, communications, and village power. This paper discusses the various design constraints of such systems and presents one technique for reducing hybrid system losses. The Southwest Technology Development Institute under contract to the National Renewable Energy Laboratory and Sandia National Laboratories has been installing data acquisition systems (DAS) on a number of small and large hybrid PV systems. These systems range from small residential systems (1 kW PV - 7 kW generator), to medium sized systems (10 kW PV - 20 kW generator), to larger systems (100 kW PV - 200 kW generator). Even larger systems are being installed with hundreds of kilowatts of PV modules, multiple wind machines, and larger diesel generators.

Modeling and Verification of Dependable Electronic Power System Architecture

NASA Astrophysics Data System (ADS)

Yuan, Ling; Fan, Ping; Zhang, Xiao-fang

The electronic power system can be viewed as a system composed of a set of concurrently interacting subsystems to generate, transmit, and distribute electric power. The complex interaction among sub-systems makes the design of electronic power system complicated. Furthermore, in order to guarantee the safe generation and distribution of electronic power, the fault tolerant mechanisms are incorporated in the system design to satisfy high reliability requirements. As a result, the incorporation makes the design of such system more complicated. We propose a dependable electronic power system architecture, which can provide a generic framework to guide the development of electronic power system to ease the development complexity. In order to provide common idioms and patterns to the system *designers, we formally model the electronic power system architecture by using the PVS formal language. Based on the PVS model of this system architecture, we formally verify the fault tolerant properties of the system architecture by using the PVS theorem prover, which can guarantee that the system architecture can satisfy high reliability requirements.

Exergy Based Analysis for the Environmental Control and Life Support Systems of the International Space Station

NASA Technical Reports Server (NTRS)

Clem, Kirk A.; Nelson, George J.; Mesmer, Bryan L.; Watson, Michael D.; Perry, Jay L.

2016-01-01

When optimizing the performance of complex systems, a logical area for concern is improving the efficiency of useful energy. The energy available for a system to perform work is defined as a system's energy content. Interactions between a system's subsystems and the surrounding environment can be accounted for by understanding various subsystem energy efficiencies. Energy balance of reactants and products, and enthalpies and entropies, can be used to represent a chemical process. Heat transfer energy represents heat loads, and flow energy represents system flows and filters. These elements allow for a system level energy balance. The energy balance equations are developed for the subsystems of the Environmental Control and Life Support (ECLS) system aboard the International Space Station (ISS). The use of these equations with system information would allow for the calculation of the energy efficiency of the system, enabling comparisons of the ISS ECLS system to other systems as well as allows for an integrated systems analysis for system optimization.

Satellite power system concept development and evaluation program. Volume 2: System definition

NASA Technical Reports Server (NTRS)

1981-01-01

The system level results of the system definition studies performed by NASA as a part of the Department of Energy/NASA satellite power system concept development and evaluation program are summarized. System requirements and guidelines are discussed as well as the major elements that comprise the reference system and its design options. Alternative system approaches including different system sizes, solid state amplifier (microwave) concepts, and laser power transmission system cost summaries are reviewed. An overview of the system analysis and planning efforts is included. The overall study led to the conclusion that the reference satellite power system concept is a feasible baseload source of electrical power and, within the assumed guidelines, the minimum cost per kilowatt is achieved at the maximum output of 5 gigawatts to the utility grid. Major unresolved technical issues include maximum allowable microwave power density in the ionosphere and performance/mass characteristics of laser power transmission systems.

Distributed systems status and control

NASA Technical Reports Server (NTRS)

Kreidler, David; Vickers, David

1990-01-01

Concepts are investigated for an automated status and control system for a distributed processing environment. System characteristics, data requirements for health assessment, data acquisition methods, system diagnosis methods and control methods were investigated in an attempt to determine the high-level requirements for a system which can be used to assess the health of a distributed processing system and implement control procedures to maintain an accepted level of health for the system. A potential concept for automated status and control includes the use of expert system techniques to assess the health of the system, detect and diagnose faults, and initiate or recommend actions to correct the faults. Therefore, this research included the investigation of methods by which expert systems were developed for real-time environments and distributed systems. The focus is on the features required by real-time expert systems and the tools available to develop real-time expert systems.

A Database-Based and Web-Based Meta-CASE System

NASA Astrophysics Data System (ADS)

Eessaar, Erki; Sgirka, Rünno

Each Computer Aided Software Engineering (CASE) system provides support to a software process or specific tasks or activities that are part of a software process. Each meta-CASE system allows us to create new CASE systems. The creators of a new CASE system have to specify abstract syntax of the language that is used in the system and functionality as well as non-functional properties of the new system. Many meta-CASE systems record their data directly in files. In this paper, we introduce a meta-CASE system, the enabling technology of which is an object-relational database system (ORDBMS). The system allows users to manage specifications of languages and create models by using these languages. The system has web-based and form-based user interface. We have created a proof-of-concept prototype of the system by using PostgreSQL ORDBMS and PHP scripting language.

Cost-effectiveness methodology for computer systems selection

NASA Technical Reports Server (NTRS)

Vallone, A.; Bajaj, K. S.

1980-01-01

A new approach to the problem of selecting a computer system design has been developed. The purpose of this methodology is to identify a system design that is capable of fulfilling system objectives in the most economical way. The methodology characterizes each system design by the cost of the system life cycle and by the system's effectiveness in reaching objectives. Cost is measured by a 'system cost index' derived from an analysis of all expenditures and possible revenues over the system life cycle. Effectiveness is measured by a 'system utility index' obtained by combining the impact that each selection factor has on the system objectives and it is assessed through a 'utility curve'. A preestablished algorithm combines cost and utility and provides a ranking of the alternative system designs from which the 'best' design is selected.

Ultra High Mass Range Mass Spectrometer System

DOEpatents

Reilly, Peter T. A. [Knoxville, TN

2005-12-06

Applicant's present invention comprises mass spectrometer systems that operate in a mass range from 1 to 10.sup.16 DA. The mass spectrometer system comprising an inlet system comprising an aerodynamic lens system, a reverse jet being a gas flux generated in an annulus moving in a reverse direction and a multipole ion guide; a digital ion trap; and a thermal vaporization/ionization detector system. Applicant's present invention further comprises a quadrupole mass spectrometer system comprising an inlet system having a quadrupole mass filter and a thermal vaporization/ionization detector system. Applicant's present invention further comprises an inlet system for use with a mass spectrometer system, a method for slowing energetic particles using an inlet system. Applicant's present invention also comprises a detector device and a method for detecting high mass charged particles.

Systems and methods for managing shared-path instrumentation and irradiation targets in a nuclear reactor

DOEpatents

Heinold, Mark R.; Berger, John F.; Loper, Milton H.; Runkle, Gary A.

2015-12-29

Systems and methods permit discriminate access to nuclear reactors. Systems provide penetration pathways to irradiation target loading and offloading systems, instrumentation systems, and other external systems at desired times, while limiting such access during undesired times. Systems use selection mechanisms that can be strategically positioned for space sharing to connect only desired systems to a reactor. Selection mechanisms include distinct paths, forks, diverters, turntables, and other types of selectors. Management methods with such systems permits use of the nuclear reactor and penetration pathways between different systems and functions, simultaneously and at only distinct desired times. Existing TIP drives and other known instrumentation and plant systems are useable with access management systems and methods, which can be used in any nuclear plant with access restrictions.

The Role of Anticipation in Intelligent Systems

NASA Astrophysics Data System (ADS)

Klir, George J.

2002-09-01

The paper explores the relationship between the area of anticipatory systems and the area of intelligent systems. After an overview of these areas, the role of anticipation in intelligent systems is discussed and it is argued that the area of intelligent systems can greatly benefit by importing the various results developed within the area of anticipatory systems. Distinctions between hard and soft systems and between hard and soft computing are then discussed. It is explained why intelligent systems are by necessity soft and why soft computing is essential for their construction. It is finally argued that the area of anticipatory systems can enlarge its scope by importing knowledge regarding soft systems and soft computing from the area of intelligent systems.

The 10 MWe Solar Thermal Central Receiver Pilot Plant: Solar facilities design integration. Pilot-plant station manual (RADL Item 2-1). Volume 1: System description

NASA Astrophysics Data System (ADS)

1982-09-01

The complete Barstow Solar Pilot Plant is described. The plant requirements and general description are presented, the mechanical, electric power, and control and instrumentation systems as well as civil engineering and structural aspects and the station buildings are described. Included in the mechanical systems are the heliostats, receiver, thermal storage system, beam characterization system, steam, water, nitrogen, and compressed air systems, chemical feed system, fire protection system, drains, sumps and the waste disposal systems, and heating, ventilating, and air conditioning systems.

A brief history and technical review of the expert system research

NASA Astrophysics Data System (ADS)

Tan, Haocheng

2017-09-01

The expert system is a computer system that emulates the decision-making ability of a human expert, which aims to solve complex problems by reasoning knowledge. It is an important branch of artificial intelligence. In this paper, firstly, we briefly introduce the development and basic structure of the expert system. Then, from the perspective of the enabling technology, we classify the current expert systems and elaborate four expert systems: The Rule-Based Expert System, the Framework-Based Expert System, the Fuzzy Logic-Based Expert System and the Expert System Based on Neural Network.

Titan 3E/Centaur D-1T Systems Summary

NASA Technical Reports Server (NTRS)

1973-01-01

A systems and operational summary of the Titan 3E/Centaur D-1T program is presented which describes vehicle assembly facilities, launch facilities, and management responsibilities, and also provides detailed information on the following separate systems: (1) mechanical systems, including structural components, insulation, propulsion units, reaction control, thrust vector control, hydraulic systems, and pneumatic equipment; (2) astrionics systems, such as instrumentation and telemetry, navigation and guidance, C-Band tracking system, and range safety command system; (3) digital computer unit software; (4) flight control systems; (5) electrical/electronic systems; and (6) ground support equipment, including checkout equipment.

Triply redundant integrated navigation and asset visibility system

DOEpatents

Smith, Stephen F [Loudon, TN; Moore, James A [Powell, TN

2011-11-29

Methods and apparatus are described for a navigation system. A method includes providing a global positioning system fix having a plurality of tracking parameters; providing a theater positioning system fix; monitoring the plurality of tracking parameters for predetermined conditions; and, when the predetermined conditions are met, sending a notifying signal and switching to the theater positioning system fix as a primary fix. An apparatus includes a system controller; a global positioning system receiver coupled to the system controller; a radio frequency locating receiver coupled to the system controller; and an operator interface coupled to the system controller.

Triply redundant integrated navigation and asset visibility system

DOEpatents

Smith, Stephen F.; Moore, James A.

2013-01-22

Methods and apparatus are described for a navigation system. A method includes providing a global positioning system fix having a plurality of tracking parameters; providing a theater positioning system fix; monitoring the plurality of tracking parameters for predetermined conditions; and, when the predetermined conditions are met, sending a notifying signal and switching to the theater positioning system fix as a primary fix. An apparatus includes a system controller; a global positioning system receiver coupled to the system controller; a radio frequency locating receiver coupled to the system controller; and an operator interface coupled to the system controller.

Serious Allergic Reactions (Anaphylaxis)

MedlinePlus

... more of these body systems: skin digestive system respiratory system cardiovascular system For example, someone may feel tightness or closing in the throat (respiratory system) together with a fast heartbeat (cardiovascular system). Here ...

46 CFR 154.1810 - Cargo manual.

Code of Federal Regulations, 2010 CFR

2010-10-01

... leakage. (4) The use of the firefighting systems on the vessel. (5) The features of the cargo containment... detection systems. (x) Alarm or safety indication systems. (xi) Cargo jettisoning system. (xii) The system...) A description of gas detection systems and alarm or safety systems. (15) A description of the...

PROCEEDINGS OF THE SYMPOSIUM ON SYSTEM THEORY, NEW YORK, N. Y. APRIL 20, 21, 22 1965. VOLUME XV.

DTIC Science & Technology

The papers presented at the symposium may be grouped as follows: (1) What is system theory ; (2) Representations of systems; (3) System dynamics; (4...Non-deterministic systems; (5) Optimal systems; and (6) Applications of system theory .

46 CFR 161.002-2 - Types of fire-protective systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., but not be limited to, automatic fire and smoke detecting systems, manual fire alarm systems, sample extraction smoke detection systems, watchman's supervisory systems, and combinations of these systems. (b) Automatic fire detecting systems. For the purpose of this subpart, automatic fire and smoke detecting...

46 CFR 161.002-2 - Types of fire-protective systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., but not be limited to, automatic fire and smoke detecting systems, manual fire alarm systems, sample extraction smoke detection systems, watchman's supervisory systems, and combinations of these systems. (b) Automatic fire detecting systems. For the purpose of this subpart, automatic fire and smoke detecting...

48 CFR 242.7000 - Contractor business system deficiencies.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Contractor business system... Business Systems 242.7000 Contractor business system deficiencies. (a) Definitions. As used in this subpart— Acceptable contractor business systems and contractor business systems are defined in the clause at 252.242...

48 CFR 242.7000 - Contractor business system deficiencies.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Contractor business system... Business Systems 242.7000 Contractor business system deficiencies. (a) Definitions. As used in this subpart— Acceptable contractor business systems and contractor business systems are defined in the clause at 252.242...

48 CFR 242.7000 - Contractor business system deficiencies.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Contractor business system... BUSINESS SYSTEMS 242.7000 Contractor business system deficiencies. (a) Definitions. As used in this subpart— Acceptable contractor business systems and contractor business systems are defined in the clause at 252.242...

48 CFR 242.7000 - Contractor business system deficiencies.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Contractor business system... BUSINESS SYSTEMS 242.7000 Contractor business system deficiencies. (a) Definitions. As used in this subpart— Acceptable contractor business systems and contractor business systems are defined in the clause at 252.242...

The Systems Approach: Its Variety of Aspects.

ERIC Educational Resources Information Center

Mattessich, Richard

1982-01-01

This concise survey of the vast literature currently available in field-of-systems thinking and cybernetics discusses the areas of systems philosophy, systems analysis (mathematical systems theory), empirical systems research, and systems engineering, and outlines contributions of selected scholars. A bibliography of 148 books and papers is…

76 FR 45336 - Departmental Offices; Privacy Act of 1974, as Amended; Systems of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-28

... systems of records entitled ``Treasury/DO .191--Human Resources and Administrative Records System.'' DATES... system of records Treasury/DO .191 entitled ``Human Resources and Administrative Records system,'' follow: Treasury/DO .191 System Name: Human Resources and Administrative Records System * * * * * Categories of...

40 CFR 86.092-2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...), general type of fuel system (i.e., carburetor or fuel injection), catalyst system (e.g., none, oxidization... control systems are emission control components or systems (and fuel metering systems) that have completed... emission control components or systems (and fuel metering systems) that do not qualify as proven emission...

40 CFR 86.092-2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...), general type of fuel system (i.e., carburetor or fuel injection), catalyst system (e.g., none, oxidization... control systems are emission control components or systems (and fuel metering systems) that have completed... emission control components or systems (and fuel metering systems) that do not qualify as proven emission...

40 CFR 86.092-2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...), general type of fuel system (i.e., carburetor or fuel injection), catalyst system (e.g., none, oxidization... control systems are emission control components or systems (and fuel metering systems) that have completed... emission control components or systems (and fuel metering systems) that do not qualify as proven emission...

Systems Engineering in NASA's R&TD Programs

NASA Technical Reports Server (NTRS)

Jones, Harry

2005-01-01

Systems engineering is largely the analysis and planning that support the design, development, and operation of systems. The most common application of systems engineering is in guiding systems development projects that use a phased process of requirements, specifications, design, and development. This paper investigates how systems engineering techniques should be applied in research and technology development programs for advanced space systems. These programs should include anticipatory engineering of future space flight systems and a project portfolio selection process, as well as systems engineering for multiple development projects.

Representing natural and manmade drainage systems in an earth system modeling framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hongyi; Wu, Huan; Huang, Maoyi

Drainage systems can be categorized into natural or geomorphological drainage systems, agricultural drainage systems and urban drainage systems. They interact closely among themselves and with climate and human society, particularly under extreme climate and hydrological events such as floods. This editorial articulates the need to holistically understand and model drainage systems in the context of climate change and human influence, and discusses the requirements and examples of feasible approaches to representing natural and manmade drainage systems in an earth system modeling framework.

LOX/hydrocarbon auxiliary propulsion system study

NASA Technical Reports Server (NTRS)

Orton, G. F.; Mark, T. D.; Weber, D. D.

1982-01-01

Liquid oxygen/hydrocarbon propulsion systems applicable to a second generation orbiter OMS/RCS were compared, and major system/component options were evaluated. A large number of propellant combinations and system concepts were evaluated. The ground rules were defined in terms of candidate propellants, system/component design options, and design requirements. System and engine component math models were incorporated into existing computer codes for system evaluations. The detailed system evaluations and comparisons were performed to identify the recommended propellant combination and system approach.

Long-term care information systems: an overview of the selection process.

PubMed

Nahm, Eun-Shim; Mills, Mary Etta; Feege, Barbara

2006-06-01

Under the current Medicare Prospective Payment System method and the ever-changing managed care environment, the long-term care information system is vital to providing quality care and to surviving in business. system selection process should be an interdisciplinary effort involving all necessary stakeholders for the proposed system. The system selection process can be modeled following the Systems Developmental Life Cycle: identifying problems, opportunities, and objectives; determining information requirements; analyzing system needs; designing the recommended system; and developing and documenting software.

Control system design method

DOEpatents

Wilson, David G [Tijeras, NM; Robinett, III, Rush D.

2012-02-21

A control system design method and concomitant control system comprising representing a physical apparatus to be controlled as a Hamiltonian system, determining elements of the Hamiltonian system representation which are power generators, power dissipators, and power storage devices, analyzing stability and performance of the Hamiltonian system based on the results of the determining step and determining necessary and sufficient conditions for stability of the Hamiltonian system, creating a stable control system based on the results of the analyzing step, and employing the resulting control system to control the physical apparatus.

An Analysis of the System Installation Costs of Diurnal Ice Storage Cooling Systems for Army Facilities

DTIC Science & Technology

1991-07-01

integrate -into the existing -structure and HVAC system. Costs-for a eutectic salt system are shown in Table 5 to compare with the DIS cooling systems. The... eutectic salt system is not an ice storage system, but is a phase change system that stores energy iniits heat of fusion and changes phase at 47 ’F

General Electric Unattended Power System Study. Addendum

DTIC Science & Technology

1980-05-01

AND NAVIGATION SYSTEMS ELECTRONIC SYSTEMS DIVISION AIR FORCE SYSTEMS COMMAND UNITED STATES AIR FORCE Hascom Air Force Base, Massachusetts DTIC C-3 B I...MITRE Corporation under Project No. 633A. The contract is sponsored by the Electronic Systems *Division, Air Force Systems Command, Hanscom Air Force...is delivered fully integrated, tested, and certified. The system consists of a combustion system, vapor generator, turbo- alternator, air -cooled

Seeking order amidst chaos: a systematic review of classification systems for causes of stillbirth and neonatal death, 2009-2014.

PubMed

Leisher, Susannah Hopkins; Teoh, Zheyi; Reinebrant, Hanna; Allanson, Emma; Blencowe, Hannah; Erwich, Jan Jaap; Frøen, J Frederik; Gardosi, Jason; Gordijn, Sanne; Gülmezoglu, A Metin; Heazell, Alexander E P; Korteweg, Fleurisca; Lawn, Joy; McClure, Elizabeth M; Pattinson, Robert; Smith, Gordon C S; Tunçalp, Ӧzge; Wojcieszek, Aleena M; Flenady, Vicki

2016-10-05

Each year, about 5.3 million babies die in the perinatal period. Understanding of causes of death is critical for prevention, yet there is no globally acceptable classification system. Instead, many disparate systems have been developed and used. We aimed to identify all systems used or created between 2009 and 2014, with their key features, including extent of alignment with the International Classification of Diseases (ICD) and variation in features by region, to inform the World Health Organization's development of a new global approach to classifying perinatal deaths. A systematic literature review (CINAHL, EMBASE, Medline, Global Health, and PubMed) identified published and unpublished studies and national reports describing new classification systems or modifications of existing systems for causes of perinatal death, or that used or tested such systems, between 2009 and 2014. Studies reporting ICD use only were excluded. Data were independently double-extracted (except from non-English publications). Subgroup analyses explored variation by extent and region. Eighty-one systems were identified as new, modifications of existing systems, or having been used between 2009 and 2014, with an average of ten systems created/modified each year. Systems had widely varying characteristics: (i) comprehensiveness (40 systems classified both stillbirths and neonatal deaths); (ii) extent of use (systems were created in 28 countries and used in 40; 17 were created for national use; 27 were widely used); (iii) accessibility (three systems available in e-format); (iv) underlying cause of death (64 systems required a single cause of death); (v) reliability (10 systems tested for reliability, with overall Kappa scores ranging from .35-.93); and (vi) ICD alignment (17 systems used ICD codes). Regional databases were not searched, so system numbers may be underestimated. Some non-differential misclassification of systems was possible. The plethora of systems in use, and continuing system development, hamper international efforts to improve understanding of causes of death. Recognition of the features of currently used systems, combined with a better understanding of the drivers of continued system creation, may help the development of a truly effective global system.

WASTE HANDLING BUILDING ELECTRICAL SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.C. Khamamkar

2000-06-23

The Waste Handling Building Electrical System performs the function of receiving, distributing, transforming, monitoring, and controlling AC and DC power to all waste handling building electrical loads. The system distributes normal electrical power to support all loads that are within the Waste Handling Building (WHB). The system also generates and distributes emergency power to support designated emergency loads within the WHB within specified time limits. The system provides the capability to transfer between normal and emergency power. The system provides emergency power via independent and physically separated distribution feeds from the normal supply. The designated emergency electrical equipment will bemore » designed to operate during and after design basis events (DBEs). The system also provides lighting, grounding, and lightning protection for the Waste Handling Building. The system is located in the Waste Handling Building System. The system consists of a diesel generator, power distribution cables, transformers, switch gear, motor controllers, power panel boards, lighting panel boards, lighting equipment, lightning protection equipment, control cabling, and grounding system. Emergency power is generated with a diesel generator located in a QL-2 structure and connected to the QL-2 bus. The Waste Handling Building Electrical System distributes and controls primary power to acceptable industry standards, and with a dependability compatible with waste handling building reliability objectives for non-safety electrical loads. It also generates and distributes emergency power to the designated emergency loads. The Waste Handling Building Electrical System receives power from the Site Electrical Power System. The primary material handling power interfaces include the Carrier/Cask Handling System, Canister Transfer System, Assembly Transfer System, Waste Package Remediation System, and Disposal Container Handling Systems. The system interfaces with the MGR Operations Monitoring and Control System for supervisory monitoring and control signals. The system interfaces with all facility support loads such as heating, ventilation, and air conditioning, office, fire protection, monitoring and control, safeguards and security, and communications subsystems.« less

76 FR 79660 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-22

...; System of Records AGENCY: Defense Information Systems Agency, DoD. ACTION: Notice to delete a system of records. SUMMARY: The Defense Information Systems Agency is deleting one system of records notices in its...: Ms. Jeanette M. Weathers-Jenkins, Defense Information Systems Agency, 6916 Cooper Avenue, Fort Meade...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 236.514 - Interconnection of cab signal system with roadway signal system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards § 236.514 Interconnection of cab signal system with roadway signal system. The automatic cab signal system shall be...

Estimating optical imaging system performance for space applications

NASA Technical Reports Server (NTRS)

Sinclair, K. F.

1972-01-01

The critical system elements of an optical imaging system are identified and a method for an initial assessment of system performance is presented. A generalized imaging system is defined. A system analysis is considered, followed by a component analysis. An example of the method is given using a film imaging system.

Applied Information Systems Research Program Workshop

NASA Technical Reports Server (NTRS)

Bredekamp, Joe

1991-01-01

Viewgraphs on Applied Information Systems Research Program Workshop are presented. Topics covered include: the Earth Observing System Data and Information System; the planetary data system; Astrophysics Data System project review; OAET Computer Science and Data Systems Programs; the Center of Excellence in Space Data and Information Sciences; and CASIS background.

5 CFR 430.204 - Agency performance appraisal system(s).

Code of Federal Regulations, 2013 CFR

2013-01-01

... Other Employees § 430.204 Agency performance appraisal system(s). (a) Each agency as defined at section... employees covered by this subpart. (b) An agency appraisal system shall establish agencywide policies and... covered by the system. At a minimum, an agency system shall— (1) Provide for— (i) Establishing employee...

5 CFR 430.204 - Agency performance appraisal system(s).

Code of Federal Regulations, 2012 CFR

2012-01-01

... Other Employees § 430.204 Agency performance appraisal system(s). (a) Each agency as defined at section... employees covered by this subpart. (b) An agency appraisal system shall establish agencywide policies and... covered by the system. At a minimum, an agency system shall— (1) Provide for— (i) Establishing employee...

5 CFR 430.204 - Agency performance appraisal system(s).

Code of Federal Regulations, 2011 CFR

2011-01-01

... Other Employees § 430.204 Agency performance appraisal system(s). (a) Each agency as defined at section... employees covered by this subpart. (b) An agency appraisal system shall establish agencywide policies and... covered by the system. At a minimum, an agency system shall— (1) Provide for— (i) Establishing employee...

5 CFR 430.204 - Agency performance appraisal system(s).

Code of Federal Regulations, 2014 CFR

2014-01-01

... Other Employees § 430.204 Agency performance appraisal system(s). (a) Each agency as defined at section... employees covered by this subpart. (b) An agency appraisal system shall establish agencywide policies and... covered by the system. At a minimum, an agency system shall— (1) Provide for— (i) Establishing employee...

Anatomy and Physiology. Health Occupations Education. Teacher's Guide.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

Nine units on anatomy and physiology are presented in this teacher's guide. The units are the following: organization and general plan of the body; skeletal and muscular systems; digestive system; circulatory system; respiratory system; nervous system and special senses; urinary system; reproductive system; and endocrine glands. Each instructional…

Fuel Distribution Systems | Energy Systems Integration Facility | NREL

Science.gov Websites

Fuel Distribution Systems Fuel Distribution Systems The Energy Systems Integration Facility's integrated fuel distribution systems provide natural gas, hydrogen, and diesel throughout its laboratories in two laboratories: the Power Systems Integration Laboratory and the Energy Storage Laboratory. Each

Building Security. Honeywell Planning Guide.

ERIC Educational Resources Information Center

Honeywell, Inc., Minneapolis, Minn.

A general discussion of building detection and alarm systems to provide security against burglary and vandalism is provided by a manufacturer of automated monitoring and control systems. Security systems are identified as--(1) local alarm system, (2) central station alarm system, (3) proprietary alarm system, and (4) direct connect alarm system..…

Energy Systems Integration Facility Control Room | Energy Systems

Science.gov Websites

Integration Facility | NREL Energy Systems Integration Facility Control Room Energy Systems Integration Facility Control Room The Energy Systems Integration Facility control room allows system engineers as the monitoring point for the facility's integrated safety and control systems. Photo of employees

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

5 CFR 430.204 - Agency performance appraisal system(s).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Agency performance appraisal system(s... Other Employees § 430.204 Agency performance appraisal system(s). (a) Each agency as defined at section 4301(1) of title 5, United States Code, shall develop one or more performance appraisal systems for...

Using SysML to model complex systems for security.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cano, Lester Arturo

2010-08-01

As security systems integrate more Information Technology the design of these systems has tended to become more complex. Some of the most difficult issues in designing Complex Security Systems (CSS) are: Capturing Requirements: Defining Hardware Interfaces: Defining Software Interfaces: Integrating Technologies: Radio Systems: Voice Over IP Systems: Situational Awareness Systems.

Analytical Assessment of the Reciprocating Feed System

NASA Technical Reports Server (NTRS)

Eddleman, David E.; Blackmon, James B.; Morton, Christopher D.

2006-01-01

A preliminary analysis tool has been created in Microsoft Excel to determine deliverable payload mass, total system mass, and performance of spacecraft systems using various types of propellant feed systems. These mass estimates are conducted by inserting into the user interface the basic mission parameters (e.g., thrust, burn time, specific impulse, mixture ratio, etc.), system architecture (e.g., propulsion system type and characteristics, propellants, pressurization system type, etc.), and design properties (e.g., material properties, safety factors, etc.). Different propellant feed and pressurization systems are available for comparison in the program. This gives the user the ability to compare conventional pressure fed, reciprocating feed system (RFS), autogenous pressurization thrust augmentation (APTA RFS), and turbopump systems with the deliverable payload, inert mass, and total system mass being the primary comparison metrics. Analyses of several types of missions and spacecraft were conducted and it was found that the RFS offers a performance improvement, especially in terms of delivered payload, over conventional pressure fed systems. Furthermore, it is competitive with a turbopump system at low to moderate chamber pressures, up to approximately 1,500 psi. Various example cases estimating the system mass and deliverable payload of several types of spacecraft are presented that illustrate the potential system performance advantages of the RFS. In addition, a reliability assessment of the RFS was conducted, comparing it to simplified conventional pressure fed and turbopump systems, based on MIL-STD 756B; these results showed that the RFS offers higher reliability, and thus substantially longer periods between system refurbishment, than turbopump systems, and is competitive with conventional pressure fed systems. This is primarily the result of the intrinsic RFS fail-operational capability with three run tanks, since the system can operate with just two run tanks.

An economic evaluation comparison of solar water pumping system with engine pumping system for rice cultivation

NASA Astrophysics Data System (ADS)

Treephak, Kasem; Thongpron, Jutturit; Somsak, Dhirasak; Saelao, Jeerawan; Patcharaprakiti, Nopporn

2015-08-01

In this paper we propose the design and economic evaluation of the water pumping systems for rice cultivation using solar energy, gasoline fuel and compare both systems. The design of the water and gasoline engine pumping system were evaluated. The gasoline fuel cost used in rice cultivation in an area of 1.6 acres. Under same conditions of water pumping system is replaced by the photovoltaic system which is composed of a solar panel, a converter and an electric motor pump which is compose of a direct current (DC) motor or an alternating current (AC) motor with an inverter. In addition, the battery is installed to increase the efficiency and productivity of rice cultivation. In order to verify, the simulation and economic evaluation of the storage energy battery system with batteries and without batteries are carried out. Finally the cost of four solar pumping systems was evaluated and compared with that of the gasoline pump. The results showed that the solar pumping system can be used to replace the gasoline water pumping system and DC solar pump has a payback less than 10 years. The systems that can payback the fastest is the DC solar pumping system without batteries storage system. The system the can payback the slowest is AC solar pumping system with batteries storage system. However, VAC motor pump of 220 V can be more easily maintained than the motor pump of 24 VDC and batteries back up system can supply a more stable power to the pump system.

48 CFR 215.407-5 - Estimating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Estimating systems. 215.407-5 Section 215.407-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM....407-5 Estimating systems. ...

48 CFR 215.407-5 - Estimating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Estimating systems. 215.407-5 Section 215.407-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM....407-5 Estimating systems. ...

48 CFR 215.407-5 - Estimating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Estimating systems. 215.407-5 Section 215.407-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM....407-5 Estimating systems. ...

48 CFR 215.407-5 - Estimating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Estimating systems. 215.407-5 Section 215.407-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM....407-5 Estimating systems. ...

48 CFR 215.407-5 - Estimating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Estimating systems. 215.407-5 Section 215.407-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM....407-5 Estimating systems. ...

Information systems in healthcare - state and steps towards sustainability.

PubMed

Lenz, R

2009-01-01

To identify core challenges and first steps on the way to sustainable information systems in healthcare. Recent articles on healthcare information technology and related articles from Medical Informatics and Computer Science were reviewed and analyzed. Core challenges that couldn't be solved over the years are identified. The two core problem areas are process integration, meaning to effectively embed IT-systems into routine workflows, and systems integration, meaning to reduce the effort for interconnecting independently developed IT-components. Standards for systems integration have improved a lot, but their usefulness is limited where system evolution is needed. Sustainable Healthcare Information Systems should be based on system architectures that support system evolution and avoid costly system replacements every five to ten years. Some basic principles for the design of such systems are separation of concerns, loose coupling, deferred systems design, and service oriented architectures.

Integrated propulsion/energy transfer control systems for lift-fan V/STOL aircraft. [reduction of total propulsion system and control system installation requirements

NASA Technical Reports Server (NTRS)

Deckert, W. H.; Rolls, L. S.

1974-01-01

An integrated propulsion/control system for lift-fan transport aircraft is described. System behavior from full-scale experimental and piloted simulator investigations are reported. The lift-fan transport is a promising concept for short-to-medium haul civil transportation and for other missions. The lift-fan transport concept features high cruise airspeed, favorable ride qualities, small perceived noise footprints, high utilization, transportation system flexibility, and adaptability to VTOL, V/STOL, or STOL configurations. The lift-fan transport has high direct operating costs in comparison to conventional aircraft, primarily because of propulsion system and aircraft low-speed control system installation requirements. An integrated lift-fan propulsion system/aircraft low-speed control system that reduces total propulsion system and control system installation requirements is discussed.

A system management methodology for building successful resource management systems

NASA Technical Reports Server (NTRS)

Hornstein, Rhoda Shaller; Willoughby, John K.

1989-01-01

This paper presents a system management methodology for building successful resource management systems that possess lifecycle effectiveness. This methodology is based on an analysis of the traditional practice of Systems Engineering Management as it applies to the development of resource management systems. The analysis produced fifteen significant findings presented as recommended adaptations to the traditional practice of Systems Engineering Management to accommodate system development when the requirements are incomplete, unquantifiable, ambiguous and dynamic. Ten recommended adaptations to achieve operational effectiveness when requirements are incomplete, unquantifiable or ambiguous are presented and discussed. Five recommended adaptations to achieve system extensibility when requirements are dynamic are also presented and discussed. The authors conclude that the recommended adaptations to the traditional practice of Systems Engineering Management should be implemented for future resource management systems and that the technology exists to build these systems extensibly.

Evaluating the success of an emergency response medical information system.

PubMed

Petter, Stacie; Fruhling, Ann

2011-07-01

STATPack™ is an information system used to aid in the diagnosis of pathogens in hospitals and state public health laboratories. STATPack™ is used as a communication and telemedicine diagnosis tool during emergencies. This paper explores the success of this emergency response medical information system (ERMIS) using a well-known framework of information systems success developed by DeLone and McLean. Using an online survey, the entire population of STATPack™ users evaluated the success of the information system by considering system quality, information quality, system use, intention to use, user satisfaction, individual impact, and organizational impact. The results indicate that the overall quality of this ERMIS (i.e., system quality, information quality, and service quality) has a positive impact on both user satisfaction and intention to use the system. However, given the nature of ERMIS, overall quality does not necessarily predict use of the system. Moreover, the user's satisfaction with the information system positively affected the intention to use the system. User satisfaction, intention to use, and system use had a positive influence on the system's impact on the individual. Finally, the organizational impacts of the system were positively influenced by use of the system and the system's individual impact on the user. The results of the study demonstrate how to evaluate the success of an ERMIS as well as introduce potential changes in how one applies the DeLone and McLean success model in an emergency response medical information system context. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Dynamic Modeling of ALS Systems

NASA Technical Reports Server (NTRS)

Jones, Harry

2002-01-01

The purpose of dynamic modeling and simulation of Advanced Life Support (ALS) systems is to help design them. Static steady state systems analysis provides basic information and is necessary to guide dynamic modeling, but static analysis is not sufficient to design and compare systems. ALS systems must respond to external input variations and internal off-nominal behavior. Buffer sizing, resupply scheduling, failure response, and control system design are aspects of dynamic system design. We develop two dynamic mass flow models and use them in simulations to evaluate systems issues, optimize designs, and make system design trades. One model is of nitrogen leakage in the space station, the other is of a waste processor failure in a regenerative life support system. Most systems analyses are concerned with optimizing the cost/benefit of a system at its nominal steady-state operating point. ALS analysis must go beyond the static steady state to include dynamic system design. All life support systems exhibit behavior that varies over time. ALS systems must respond to equipment operating cycles, repair schedules, and occasional off-nominal behavior or malfunctions. Biological components, such as bioreactors, composters, and food plant growth chambers, usually have operating cycles or other complex time behavior. Buffer sizes, material stocks, and resupply rates determine dynamic system behavior and directly affect system mass and cost. Dynamic simulation is needed to avoid the extremes of costly over-design of buffers and material reserves or system failure due to insufficient buffers and lack of stored material.

Sustainability evaluation of different systems for sea cucumber ( Apostichopus japonicus) farming based on emergy theory

NASA Astrophysics Data System (ADS)

Wang, Guodong; Dong, Shuanglin; Tian, Xiangli; Gao, Qinfeng; Wang, Fang

2015-06-01

Emergy analysis is effective for analyzing ecological economic systems. However, the accuracy of the approach is affected by the diversity of economic level, meteorological and hydrological parameters in different regions. The present study evaluated the economic benefits, environmental impact, and sustainability of indoor, semi-intensive and extensive farming systems of sea cucumber ( Apostichopus japonicus) in the same region. The results showed that A. japonicus indoor farming system was high in input and output (yield) whereas pond extensive farming system was low in input and output. The output/input ratio of indoor farming system was lower than that of pond extensive farming system, and the output/input ratio of semi-intensive farming system fell in between them. The environmental loading ratio of A. japonicus extensive farming system was lower than that of indoor farming system. In addition, the emergy yield and emergy exchange ratios, and emergy sustainability and emergy indexes for sustainable development were higher in extensive farming system than those in indoor farming system. These results indicated that the current extensive farming system exerted fewer negative influences on the environment, made more efficient use of available resources, and met more sustainable development requirements than the indoor farming system. A. japonicus farming systems showed more emergy benefits than fish farming systems. The pond farming systems of A. japonicus exploited more free local environmental resources for production, caused less potential pressure on the local environment, and achieved higher sustainability than indoor farming system.

System design in an evolving system-of-systems architecture and concept of operations

NASA Astrophysics Data System (ADS)

Rovekamp, Roger N., Jr.

Proposals for space exploration architectures have increased in complexity and scope. Constituent systems (e.g., rovers, habitats, in-situ resource utilization facilities, transfer vehicles, etc) must meet the needs of these architectures by performing in multiple operational environments and across multiple phases of the architecture's evolution. This thesis proposes an approach for using system-of-systems engineering principles in conjunction with system design methods (e.g., Multi-objective optimization, genetic algorithms, etc) to create system design options that perform effectively at both the system and system-of-systems levels, across multiple concepts of operations, and over multiple architectural phases. The framework is presented by way of an application problem that investigates the design of power systems within a power sharing architecture for use in a human Lunar Surface Exploration Campaign. A computer model has been developed that uses candidate power grid distribution solutions for a notional lunar base. The agent-based model utilizes virtual control agents to manage the interactions of various exploration and infrastructure agents. The philosophy behind the model is based both on lunar power supply strategies proposed in literature, as well as on the author's own approaches for power distribution strategies of future lunar bases. In addition to proposing a framework for system design, further implications of system-of-systems engineering principles are briefly explored, specifically as they relate to producing more robust cross-cultural system-of-systems architecture solutions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dawn Lenz; Raymond T. Lines; Darryl Murdock

ITT Industries Space Systems Division (Space Systems) has developed an airborne natural gas leak detection system designed to detect, image, quantify, and precisely locate leaks from natural gas transmission pipelines. This system is called the Airborne Natural Gas Emission Lidar (ANGEL) system. The ANGEL system uses a highly sensitive differential absorption Lidar technology to remotely detect pipeline leaks. The ANGEL System is operated from a fixed wing aircraft and includes automatic scanning, pointing system, and pilot guidance systems. During a pipeline inspection, the ANGEL system aircraft flies at an elevation of 1000 feet above the ground at speeds of betweenmore » 100 and 150 mph. Under this contract with DOE/NETL, Space Systems was funded to integrate the ANGEL sensor into a test aircraft and conduct a series of flight tests over a variety of test targets including simulated natural gas pipeline leaks. Following early tests in upstate New York in the summer of 2004, the ANGEL system was deployed to Casper, Wyoming to participate in a set of DOE-sponsored field tests at the Rocky Mountain Oilfield Testing Center (RMOTC). At RMOTC the Space Systems team completed integration of the system and flew an operational system for the first time. The ANGEL system flew 2 missions/day for the duration for the 5-day test. Over the course of the week the ANGEL System detected leaks ranging from 100 to 5,000 scfh.« less

A 12-year retrospective review of bullous systemic lupus erythematosus in cutaneous and systemic lupus erythematosus patients.

PubMed

Chanprapaph, K; Sawatwarakul, S; Vachiramon, V

2017-10-01

Objective The aim of this study was to investigate the clinical features, laboratory findings, systemic manifestations, treatment and outcome of patients with bullous systemic lupus erythematosus in a tertiary care center in Thailand. Methods We performed a retrospective review from 2002 to 2014 of all patients who fulfilled the diagnostic criteria for bullous systemic lupus erythematosus to evaluate for the clinical characteristics, extracutaneous involvement, histopathologic features, immunofluorescence pattern, serological abnormalities, internal organ involvement, treatments and outcome. Results Among 5149 patients with cutaneous lupus erythematosus and/or systemic lupus erythematosus, 15 developed vesiculobullous lesions. Ten patients had validation of the diagnosis of bullous systemic lupus erythematosus, accounting for 0.19%. Bullous systemic lupus erythematosus occurred after the diagnosis of systemic lupus erythematosus in six patients with a median onset of 2.5 months (0-89). Four out of 10 patients developed bullous systemic lupus erythematosus simultaneously with systemic lupus erythematosus. Hematologic abnormalities and renal involvement were found in 100% and 90%, respectively. Polyarthritis (40%) and serositis (40%) were less frequently seen. Systemic corticosteroids, immunosuppressants, antimalarials and dapsone offered resolution of cutaneous lesions. Conclusion Bullous systemic lupus erythematosus is an uncommon presentation of systemic lupus erythematosus. Blistering can occur following or simultaneously with established systemic lupus erythematosus. We propose that clinicians should carefully search for systemic involvement, especially hematologic and renal impairment, in patients presenting with bullous systemic lupus erythematosus.

Permanent magnet synchronous motor servo system control based on μC/OS

NASA Astrophysics Data System (ADS)

Shi, Chongyang; Chen, Kele; Chen, Xinglong

2015-10-01

When Opto-Electronic Tracking system operates in complex environments, every subsystem must operate efficiently and stably. As a important part of Opto-Electronic Tracking system, the performance of PMSM(Permanent Magnet Synchronous Motor) servo system affects the Opto-Electronic Tracking system's accuracy and speed greatly[1][2]. This paper applied embedded real-time operating system μC/OS to the control of PMSM servo system, implemented SVPWM(Space Vector Pulse Width Modulation) algorithm in PMSM servo system, optimized the stability of PMSM servo system. Pointing on the characteristics of the Opto-Electronic Tracking system, this paper expanded μC/OS with software redundancy processes, remote debugging and upgrading. As a result, the Opto- Electronic Tracking system performs efficiently and stably.

Multiswitching combination synchronisation of non-identical fractional-order chaotic systems

NASA Astrophysics Data System (ADS)

Bhat, Muzaffar Ahmad; Khan, Ayub

2018-06-01

In this paper, multiswitching combination synchronisation (MSCS) scheme has been investigated in a class of three non-identical fractional-order chaotic systems. The fractional-order Lorenz and Chen systems are taken as the drive systems. The combination of multidrive systems is then synchronised with the fractional-order Lü chaotic system. In MSCS, the state variables of the two drive systems synchronise with different state variables of the response system, simultaneously. Based on the stability of fractional-order chaotic systems, the MSCS of three fractional-order non-identical systems has been investigated. For the synchronisation of three non-identical fractional-order chaotic systems, suitable controllers have been designed. Theoretical analysis and numerical results are presented to demonstrate the validity and feasibility of the applied method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washiya, Tadahiro; Komaki, Jun; Funasaka, Hideyuki

Japan Atomic Energy Agency (JAEA) has been developing the new aqueous reprocessing system named 'NEXT' (New Extraction system for TRU recovery)1-2, which provides many advantages as waste volume reduction, cost savings by advanced components and simplification of process operation. Advanced head-end systems in the 'NEXT' process consist of fuel disassembly system, fuel shearing system and continuous dissolver system. We developed reliable fuel disassembly system with innovative procedure, and short-length shearing system and continuous dissolver system can be provided highly concentrated dissolution to adapt to the uranium crystallization process. We have carried out experimental studies, and fabrication of engineering-scale test devicesmore » to confirm the systems performance. In this paper, research and development of advanced head-end systems are described. (authors)« less

A Decision Support System for Evaluating Systems of Undersea Sensors and Weapons

DTIC Science & Technology

2015-12-01

distribution is unlimited A DECISION SUPPORT SYSTEM FOR EVALUATING SYSTEMS OF UNDERSEA SENSORS AND WEAPONS by Team Mental Focus Cohort 142O...A DECISION SUPPORT SYSTEM FOR EVALUATING SYSTEMS OF UNDERSEA SENSORS AND WEAPONS 5. FUNDING NUMBERS 6. AUTHOR(S) Systems Engineering Cohort...undersea weapons, it requires the supporting tools to evaluate and predict the effectiveness of these system concepts. While current naval minefield

Sea Lance Littoral Warfare Small Combatant System

DTIC Science & Technology

2001-01-01

integrated with the Ship Wide Area Network (SWAN) that control the Damage Control System ii. Firemain System iii. AFFF Bilge Sprinkling System iv. FM-200...dcarm/ 156 ix. Provide seawater for magazine sprinkling system. x. Provide seawater to AFFF bilge sprinkling system. xi. Provide seawater...cooling for auxiliary systems. xii. Provide seawater for eductor system. In the event of a major fuel oil leak, AFFF is an ideal substance to cover

An Event-driven, Value-based, Pull Systems Engineering Scheduling Approach

DTIC Science & Technology

2012-03-01

engineering in rapid response environments has been difficult, particularly those where large, complex brownfield systems or systems of systems exist and...where large, complex brownfield systems or systems of systems exist and are constantly being updated with both short and long term software enhancements...2004. [13] B. Boehm, “Applying the Incremental Commitment Model to Brownfield System Development,” Proceedings, CSER, 2009. [14] A. Borshchev and A

Sustaining Competitive Advantage: Mental Models and Organizational Learning for Future Marines

DTIC Science & Technology

2007-01-01

Soft Systems Methodology : Other Voices.” Systemic Practice and Action Research. 13, no. 6, (2000): 773. Larsen, Kai R. T., Claire McInerney...30. Mingers, John. “An Idea Ahead of Its Time: The History and Development of Soft Systems Methodology .” Systemic Practice and Action...Soft System Dynamics Methodology (SSDM): Combinging Soft Systems Methodology (SSM) and System Dynamics (SD).” Systemic Practice and Action

Impact of Organic and Conventional Systems of Coffee Farming on Soil Properties and Culturable Microbial Diversity

PubMed Central

2016-01-01

A study was undertaken with an objective of evaluating the long-term impacts of organic (ORG) and conventional (CON) methods of coffee farming on soil physical, chemical, biological, and microbial diversity. Electrical conductivity and bulk density were found to increase by 34% and 21%, respectively, in CON compared to ORG system, while water holding capacity was found decreased in both the systems. Significant increase in organic carbon was observed in ORG system. Major nutrients, nitrogen and potassium, levels showed inclination in both ORG and CON system, but the trend was much more pronounced in CON system. Phosphorus was found to increase in both ORG and CON system, but its availability was found to be more with CON system. In biological attributes, higher soil respiration and fluorescein diacetate activity were recorded in ORG system compared to CON system. Higher soil urease activity was observed in CON system, while dehydrogenase activity does not show significant differences between ORG and CON systems. ORG system was found to have higher macrofauna (31.4%), microbial population (34%), and microbial diversity indices compared to CON system. From the present study, it is accomplished that coffee soil under long-term ORG system has better soil properties compared to CON system. PMID:27042378

Impact of Organic and Conventional Systems of Coffee Farming on Soil Properties and Culturable Microbial Diversity.

PubMed

Velmourougane, Kulandaivelu

2016-01-01

A study was undertaken with an objective of evaluating the long-term impacts of organic (ORG) and conventional (CON) methods of coffee farming on soil physical, chemical, biological, and microbial diversity. Electrical conductivity and bulk density were found to increase by 34% and 21%, respectively, in CON compared to ORG system, while water holding capacity was found decreased in both the systems. Significant increase in organic carbon was observed in ORG system. Major nutrients, nitrogen and potassium, levels showed inclination in both ORG and CON system, but the trend was much more pronounced in CON system. Phosphorus was found to increase in both ORG and CON system, but its availability was found to be more with CON system. In biological attributes, higher soil respiration and fluorescein diacetate activity were recorded in ORG system compared to CON system. Higher soil urease activity was observed in CON system, while dehydrogenase activity does not show significant differences between ORG and CON systems. ORG system was found to have higher macrofauna (31.4%), microbial population (34%), and microbial diversity indices compared to CON system. From the present study, it is accomplished that coffee soil under long-term ORG system has better soil properties compared to CON system.

Spacecraft systems engineering: An introduction to the process at GSFC

NASA Technical Reports Server (NTRS)

Fragomeni, Tony; Ryschkewitsch, Michael G.

1993-01-01

The main objective in systems engineering is to devise a coherent total system design capable of achieving the stated requirements. Requirements should be rigid. However, they should be continuously challenged, rechallenged and/or validated. The systems engineer must specify every requirement in order to design, document, implement and conduct the mission. Each and every requirement must be logically considered, traceable and evaluated through various analysis and trade studies in a total systems design. Margins must be determined to be realistic as well as adequate. The systems engineer must also continuously close the loop and verify system performance against the requirements. The fundamental role of the systems engineer, however, is to engineer, not manage. Yet, in large, complex missions, where more than one systems engineer is required, someone needs to manage the systems engineers, and we call them 'systems managers.' Systems engineering management is an overview function which plans, guides, monitors and controls the technical execution of a project as implemented by the systems engineers. As the project moves on through Phases A and B into Phase C/D, the systems engineering tasks become a small portion of the total effort. The systems management role increases since discipline subsystem engineers are conducting analyses and reviewing test data for final review and acceptance by the systems managers.

A comparative analysis of area navigation systems in general aviation. M.S. Thesis

NASA Technical Reports Server (NTRS)

Dodge, S. M.

1973-01-01

Radio navigation systems which offer the capabilities of area navigation to general aviation operators are discussed. The systems considered are: (1) the VORTAC system, (2) the Loran-C system, and (3) the Differential Omega system. The inital analyses are directed toward a comparison of the systems with respect to their compliance to specified performance parameters and to the cost effectiveness of each system in relation to those specifications. Further analyses lead to the development of system cost sensitivity charts, and the employment of these charts allows conclusions to be drawn relative to the cost-effectiveness of the candidate navigation system.

Automotive Stirling engine system component review

NASA Technical Reports Server (NTRS)

Hindes, Chip; Stotts, Robert

1987-01-01

The design and testing of the power and combustion control system for the basic Stirling engine, Mod II, are examined. The power control system is concerned with transparent operation, and the Mod II uses engine working gas pressure variation to control the power output of the engine. The main components of the power control system, the power control valve, the pump-down system, and the hydrogen stable system, are described. The combustion control system consists of a combustion air supply system and an air/fuel ratio control system, and the system is to maintain constant heater head temperature, and to maximize combustion efficiency and to minimize exhaust emissions.

Systems and Methods for Parameter Dependent Riccati Equation Approaches to Adaptive Control

NASA Technical Reports Server (NTRS)

Kim, Kilsoo (Inventor); Yucelen, Tansel (Inventor); Calise, Anthony J. (Inventor)

2015-01-01

Systems and methods for adaptive control are disclosed. The systems and methods can control uncertain dynamic systems. The control system can comprise a controller that employs a parameter dependent Riccati equation. The controller can produce a response that causes the state of the system to remain bounded. The control system can control both minimum phase and non-minimum phase systems. The control system can augment an existing, non-adaptive control design without modifying the gains employed in that design. The control system can also avoid the use of high gains in both the observer design and the adaptive control law.

Learning the organization: a model for health system analysis for new nurse administrators.

PubMed

Clark, Mary Jo

2004-01-01

Health systems are large and complex organizations in which multiple components and processes influence system outcomes. In order to effectively position themselves in such organizations, nurse administrators new to a system must gain a rapid understanding of overall system operation. Such understanding is facilitated by use of a model for system analysis. The model presented here examines the dynamic interrelationships between and among internal and external elements as they affect system performance. External elements to be analyzed include environmental factors and characteristics of system clientele. Internal elements flow from the mission and goals of the system and include system culture, services, resources, and outcomes.

An approach to operating system testing

NASA Technical Reports Server (NTRS)

Sum, R. N., Jr.; Campbell, R. H.; Kubitz, W. J.

1984-01-01

To ensure the reliability and performance of a new system, it must be verified or validated in some manner. Currently, testing is the only resonable technique available for doing this. Part of this testing process is the high level system test. System testing is considered with respect to operating systems and in particular UNIX. This consideration results in the development and presentation of a good method for performing the system test. The method includes derivations from the system specifications and ideas for management of the system testing project. Results of applying the method to the IBM System/9000 XENIX operating system test and the development of a UNIX test suite are presented.

Selection of neural network structure for system error correction of electro-optical tracker system with horizontal gimbal

NASA Astrophysics Data System (ADS)

Liu, Xing-fa; Cen, Ming

2007-12-01

Neural Network system error correction method is more precise than lest square system error correction method and spheric harmonics function system error correction method. The accuracy of neural network system error correction method is mainly related to the frame of Neural Network. Analysis and simulation prove that both BP neural network system error correction method and RBF neural network system error correction method have high correction accuracy; it is better to use RBF Network system error correction method than BP Network system error correction method for little studying stylebook considering training rate and neural network scale.

Initial system design method for non-rotationally symmetric systems based on Gaussian brackets and Nodal aberration theory.

PubMed

Zhong, Yi; Gross, Herbert

2017-05-01

Freeform surfaces play important roles in improving the imaging performance of off-axis optical systems. However, for some systems with high requirements in specifications, the structure of the freeform surfaces could be very complicated and the number of freeform surfaces could be large. That brings challenges in fabrication and increases the cost. Therefore, to achieve a good initial system with minimum aberrations and reasonable structure before implementing freeform surfaces is essential for optical designers. The already existing initial system design methods are limited to certain types of systems. A universal tool or method to achieve a good initial system efficiently is very important. In this paper, based on the Nodal aberration theory and the system design method using Gaussian Brackets, the initial system design method is extended from rotationally symmetric systems to general non-rotationally symmetric systems. The design steps are introduced and on this basis, two off-axis three-mirror systems are pre-designed using spherical shape surfaces. The primary aberrations are minimized using the nonlinear least-squares solver. This work provides insight and guidance for initial system design of off-axis mirror systems.

Advanced Ground Systems Maintenance Physics Models For Diagnostics Project

NASA Technical Reports Server (NTRS)

Perotti, Jose M.

2015-01-01

The project will use high-fidelity physics models and simulations to simulate real-time operations of cryogenic and systems and calculate the status/health of the systems. The project enables the delivery of system health advisories to ground system operators. The capability will also be used to conduct planning and analysis of cryogenic system operations. This project will develop and implement high-fidelity physics-based modeling techniques tosimulate the real-time operation of cryogenics and other fluids systems and, when compared to thereal-time operation of the actual systems, provide assessment of their state. Physics-modelcalculated measurements (called “pseudo-sensors”) will be compared to the system real-timedata. Comparison results will be utilized to provide systems operators with enhanced monitoring ofsystems' health and status, identify off-nominal trends and diagnose system/component failures.This capability can also be used to conduct planning and analysis of cryogenics and other fluidsystems designs. This capability will be interfaced with the ground operations command andcontrol system as a part of the Advanced Ground Systems Maintenance (AGSM) project to helpassure system availability and mission success. The initial capability will be developed for theLiquid Oxygen (LO2) ground loading systems.

Significance of User Participation in a Hospital Information System Success: Insights From a Case Study.

PubMed

Saleem, Naveed; Steel, Douglas; Gercek, Gokhan; Chandra, Ashish

User participation in the development of a system is universally prescribed as an effective strategy to ensure the success of the resultant system. However, the existing literature on the merits of user participation only provides equivocal evidence. Various analyses of this literature point out that this equivocal evidence may be due to inconsistent operational measures of the user participation and system success constructs. Planned organizational change and participative decision making, the underlying paradigms of user participation construct, suggest that the development of some information systems may require blending of users' system-related functional expertise and developers' technical expertise to ensure system success. These paradigms also maintain that in case of well-defined, structured information systems user participation should enhance the likelihood of system success through better user understanding of the need for the system and system content and objectives, user trust, and a sense of system ownership. This research also described a case study involving the development and implementation of a medical records system for a neonatal intensive care unit in a large hospital in Texas. The case study provides evidence that in systems that require incorporation of user functional expertise user participation will enhance the likelihood of system success.

Agreement of three interpretation systems of intrapartum foetal heart rate monitoring by different levels of physicians.

PubMed

Pruksanusak, Ninlapa; Thongphanang, Putthaporn; Chainarong, Natthicha; Suntharasaj, Thitima; Kor-Anantakul, Ounjai; Suwanrath, Chitkasaem; Petpichetchian, Chusana

2017-11-01

A prospective study was conducted in centre in Southern Thailand, to evaluate agreement in EFM interpretation among various physicians in order to find out the most practical system for daily use. We found strong agreement of very normal FHR tracings among the FIGO, NICHD 3-tier and 5-tier systems. The NICHD 3-tier was more compatible with the FIGO system than 5-tier system. Overall inter-observer agreement was moderate for the NICHD 3-tier system while inter-observer agreement of 5-tier system was fair also the intra-observer agreement was higher in the NICHD 3-tier system. So the 3-tier systems are more suitable than the 5-tier system in general obstetric practice. Impact statement What is already known on this subject: The 3-tier and 5-tier systems were widely used in general obstetrics practice. What the results of this study add: The inter- and intra-observer agreement of NICHD 3-tier system was higher than the 5-tier system. What the implications are of these findings for clinical practice and/or further research: The 3-tier systems were more suitable than the 5-tier systems in general obstetrics practice.

Forest fire advanced system technology (FFAST) conceptual design study

NASA Technical Reports Server (NTRS)

Nichols, J. David; Warren, John R.

1987-01-01

The National Aeronautics and Space Administration's Jet Propulsion Laboratory (JPL) and the U.S. Department of Agriculture (USDA) Forest Service completed a conceptual design study that defined an integrated forest fire detection and mapping system that will be based upon technology available in the 1990s. Potential system configuration options in emerging and advanced technologies related to the conceptual design were identified and recommended for inclusion as preferred system components. System component technologies identified for an end-to-end system include airborne mounted, thermal infrared (IR) linear array detectors, automatic onboard georeferencing and signal processing, geosynchronous satellite communications links, and advanced data integration and display. Potential system configuration options were developed and examined for possible inclusion in the preferred system configuration. The preferred system configuration will provide increased performance and be cost effective over the system currently in use. Forest fire management user requirements and the system component emerging technologies were the basis for the system configuration design. The conceptual design study defined the preferred system configuration that warrants continued refinement and development, examined economic aspects of the current and preferred system, and provided preliminary cost estimates for follow-on system prototype development.

A Combined Energy Management Algorithm for Wind Turbine/Battery Hybrid System

NASA Astrophysics Data System (ADS)

Altin, Necmi; Eyimaya, Süleyman Emre

2018-03-01

From an energy management standpoint, natural phenomena such as solar irradiation and wind speed are uncontrolled variables, so the correlation between the energy generated by renewable energy sources and energy demand cannot always be predicted. For this reason, energy storage systems are used to provide more efficient renewable energy systems. In these systems, energy management systems are used to control the energy storage system and establish a balance between the generated power and the power demand. In addition, especially in wind turbines, rapidly varying wind speeds cause wind power fluctuations, which threaten the power system stability, especially at high power levels. Energy storage systems are also used to mitigate the power fluctuations and sustain the power system's stability. In these systems, another controller which controls the energy storage system power to mitigate power fluctuations is required. These two controllers are different from each other. In this study, a combined energy management algorithm is proposed which can perform both as an energy control system and a power fluctuation mitigation system. The proposed controller is tested with wind energy conversion system modeled in MATLAB/Simulink. Simulation results show that the proposed controller acts as an energy management system while, at the same time, mitigating power fluctuations.

CANISTER TRANSFER SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

B. Gorpani

2000-06-23

The Canister Transfer System receives transportation casks containing large and small disposable canisters, unloads the canisters from the casks, stores the canisters as required, loads them into disposal containers (DCs), and prepares the empty casks for re-shipment. Cask unloading begins with cask inspection, sampling, and lid bolt removal operations. The cask lids are removed and the canisters are unloaded. Small canisters are loaded directly into a DC, or are stored until enough canisters are available to fill a DC. Large canisters are loaded directly into a DC. Transportation casks and related components are decontaminated as required, and empty casks aremore » prepared for re-shipment. One independent, remotely operated canister transfer line is provided in the Waste Handling Building System. The canister transfer line consists of a Cask Transport System, Cask Preparation System, Canister Handling System, Disposal Container Transport System, an off-normal canister handling cell with a transfer tunnel connecting the two cells, and Control and Tracking System. The Canister Transfer System operating sequence begins with moving transportation casks to the cask preparation area with the Cask Transport System. The Cask Preparation System prepares the cask for unloading and consists of cask preparation manipulator, cask inspection and sampling equipment, and decontamination equipment. The Canister Handling System unloads the canister(s) and places them into a DC. Handling equipment consists of a bridge crane hoist, DC loading manipulator, lifting fixtures, and small canister staging racks. Once the cask has been unloaded, the Cask Preparation System decontaminates the cask exterior and returns it to the Carrier/Cask Handling System via the Cask Transport System. After the DC is fully loaded, the Disposal Container Transport System moves the DC to the Disposal Container Handling System for welding. To handle off-normal canisters, a separate off-normal canister handling cell is located adjacent to the canister transfer cell and is interconnected to the transfer cell by means of the off-normal canister transfer tunnel. All canister transfer operations are controlled by the Control and Tracking System. The system interfaces with the Carrier/Cask Handling System for incoming and outgoing transportation casks. The system also interfaces with the Disposal Container Handling System, which prepares the DC for loading and subsequently seals the loaded DC. The system support interfaces are the Waste Handling Building System and other internal Waste Handling Building (WHB) support systems.« less

10 CFR 50.46a - Acceptance criteria for reactor coolant system venting systems.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Acceptance criteria for reactor coolant system venting... criteria for reactor coolant system venting systems. Each nuclear power reactor must be provided with high point vents for the reactor coolant system, for the reactor vessel head, and for other systems required...

10 CFR 50.46a - Acceptance criteria for reactor coolant system venting systems.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Acceptance criteria for reactor coolant system venting... criteria for reactor coolant system venting systems. Each nuclear power reactor must be provided with high point vents for the reactor coolant system, for the reactor vessel head, and for other systems required...

46 CFR 153.432 - Cooling systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Cooling systems. 153.432 Section 153.432 Shipping COAST... Control Systems § 153.432 Cooling systems. (a) Each cargo cooling system must have an equivalent standby... cooling system. (b) Each tankship that has a cargo tank with a required cooling system must have a manual...

46 CFR 153.432 - Cooling systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Cooling systems. 153.432 Section 153.432 Shipping COAST... Control Systems § 153.432 Cooling systems. (a) Each cargo cooling system must have an equivalent standby... cooling system. (b) Each tankship that has a cargo tank with a required cooling system must have a manual...

46 CFR 153.432 - Cooling systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Cooling systems. 153.432 Section 153.432 Shipping COAST... Control Systems § 153.432 Cooling systems. (a) Each cargo cooling system must have an equivalent standby... cooling system. (b) Each tankship that has a cargo tank with a required cooling system must have a manual...

40 CFR 280.70 - Temporary closure.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (UST) Out-of-Service UST Systems and Closure § 280.70 Temporary closure. (a) When an UST system is... the UST system is empty. The UST system is empty when all materials have been removed using commonly... the total capacity of the UST system, remain in the system. (b) When an UST system is temporarily...

40 CFR 280.70 - Temporary closure.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (UST) Out-of-Service UST Systems and Closure § 280.70 Temporary closure. (a) When an UST system is... the UST system is empty. The UST system is empty when all materials have been removed using commonly... the total capacity of the UST system, remain in the system. (b) When an UST system is temporarily...

40 CFR 280.70 - Temporary closure.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (UST) Out-of-Service UST Systems and Closure § 280.70 Temporary closure. (a) When an UST system is... the UST system is empty. The UST system is empty when all materials have been removed using commonly... the total capacity of the UST system, remain in the system. (b) When an UST system is temporarily...

40 CFR 280.70 - Temporary closure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (UST) Out-of-Service UST Systems and Closure § 280.70 Temporary closure. (a) When an UST system is... the UST system is empty. The UST system is empty when all materials have been removed using commonly... the total capacity of the UST system, remain in the system. (b) When an UST system is temporarily...

40 CFR 280.70 - Temporary closure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (UST) Out-of-Service UST Systems and Closure § 280.70 Temporary closure. (a) When an UST system is... the UST system is empty. The UST system is empty when all materials have been removed using commonly... the total capacity of the UST system, remain in the system. (b) When an UST system is temporarily...

78 FR 16756 - Twenty-Second Meeting: RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-18

... Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY: Federal Aviation... 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing..., Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held April...

77 FR 16890 - Eighteenth Meeting: RTCA Special Committee 213, Enhanced Flight Visions Systems/Synthetic Vision...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

... Committee 213, Enhanced Flight Visions Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY: Federal Aviation... 213, Enhanced Flight Visions Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing... Flight Visions Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held April 17-19...

Working with Systems and Thinking Systemically--Disentangling the Crossed Wires

ERIC Educational Resources Information Center

Fox, Mark

2009-01-01

This article explores two separate traditions that educational psychologists (EPs) in the UK have for working with systems. One of these is "systems work" with organisations such as schools. The other is "systemic thinking" for working with families. Over the years these two traditions, systems work and systemic thinking, have…

46 CFR 153.430 - Heat transfer systems; general.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's heat...

46 CFR 153.430 - Heat transfer systems; general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's heat...

46 CFR 153.430 - Heat transfer systems; general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's heat...

Automated Instructional Management Systems (AIMS) Version III, Operator's Guide.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

This manual gives the instructions necessary to understand and operate the Automated Instructional Management System (AIMS), utilizing IBM System 360, Model 30/Release 20 Disk Operating System, and the OpScan 100 System Reader and Tape Unit. It covers the AIMS III system initialization, system and operational input, requirements, master response…

78 FR 5557 - Twenty-First Meeting: RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic Vision...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-25

... Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY: Federal Aviation... 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing..., Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held...

78 FR 55774 - Twenty Fourth Meeting: RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-11

... Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY: Federal Aviation... 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing..., Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held October...

75 FR 17202 - Eighth Meeting: Joint RTCA Special Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY...-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing...: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held April...

77 FR 56254 - Twentieth Meeting: RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic Vision...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-12

... Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY: Federal Aviation... 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY: The FAA is issuing... Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will be held October 2-4...

76 FR 39394 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-06

...: The Department of the Navy is deleting a system of records notice in its existing inventory of record... Navy proposes to delete a systems of records notice from its inventory of record systems subject to the... operation. This system, Personnel Action Reporting System (PARS) was a sunset system and all records...

40 CFR 63.1012 - Compressor standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... fluid system degassing reservoir that is routed to a process or fuel gas system or connected by a closed... sensor that will detect failure of the seal system, barrier fluid system, or both. Each sensor shall be... the seal system, the barrier fluid system, or both. If the sensor indicates failure of the seal system...

40 CFR 63.1012 - Compressor standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fluid system degassing reservoir that is routed to a process or fuel gas system or connected by a closed... sensor that will detect failure of the seal system, barrier fluid system, or both. Each sensor shall be... the seal system, the barrier fluid system, or both. If the sensor indicates failure of the seal system...

New Systems Produced by Systemic Change

ERIC Educational Resources Information Center

Battino, Wendy; Clem, Jo; Caine, Renate N.; Reigeluth, Charles M.; Chapman, Carrie; Flinders, David J.; Malopinsky, Larissa V.

2006-01-01

This article presents new systems produced by systemic change. First is Systemic Changes in the Chugach School District by Wendy Battino and Jo Clem. Second is Systemic Changes in Public Schools through Brain-Based Learning by Renate N. Caine. Third is A Vision of an Information-Age Educational System by Charles M. Reigeluth. Fourth is Systemic…

MSFC Skylab Orbital Workshop, volume 4. [design and development of life support systems

NASA Technical Reports Server (NTRS)

1974-01-01

The design and development of specific systems on the Skylab Orbital Laboratory are discussed. The subjects considered are: (1) pressure garment conditioning system, (2) stowage system, (3) ground support equipment systems, and (4) marking systems illustrations of the system components are provided. Results of performance tests are discussed.

46 CFR 153.430 - Heat transfer systems; general.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's heat...

46 CFR 153.430 - Heat transfer systems; general.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's heat...

75 FR 44306 - Eleventh Meeting: Joint RTCA Special Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

... Committee 213: EUROCAE WG- 79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY... Special Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS... 213: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The...

75 FR 71183 - Twelfth Meeting: Joint RTCA Special Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-22

... Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS) AGENCY... Committee 213: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). SUMMARY...: EUROCAE WG-79: Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS). DATES: The meeting will...

46 CFR 153.432 - Cooling systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Cooling systems. 153.432 Section 153.432 Shipping COAST... Control Systems § 153.432 Cooling systems. (a) Each cargo cooling system must have an equivalent standby... cooling system. (b) Each tankship that has a cargo tank with a required cooling system must have a manual...

Proceedings of the 1984 IEEE international conference on systems, man and cybernetics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-01-01

This conference contains papers on artificial intelligence, pattern recognition, and man-machine systems. Topics considered include concurrent minimization, a robot programming system, system modeling and simulation, camera calibration, thermal power plants, image processing, fault diagnosis, knowledge-based systems, power systems, hydroelectric power plants, expert systems, and electrical transients.

28 CFR 16.130 - Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Systems: Correspondence Management Systems for the Department of Justice (DOJ-003); Freedom of Information... PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Exemption of Records Systems Under the Privacy Act § 16.130 Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

28 CFR 16.130 - Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Systems: Correspondence Management Systems for the Department of Justice (DOJ-003); Freedom of Information... PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Exemption of Records Systems Under the Privacy Act § 16.130 Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

28 CFR 16.130 - Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Systems: Correspondence Management Systems for the Department of Justice (DOJ-003); Freedom of Information... PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Exemption of Records Systems Under the Privacy Act § 16.130 Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

28 CFR 16.130 - Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Systems: Correspondence Management Systems for the Department of Justice (DOJ-003); Freedom of Information... PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Exemption of Records Systems Under the Privacy Act § 16.130 Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

28 CFR 16.130 - Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Systems: Correspondence Management Systems for the Department of Justice (DOJ-003); Freedom of Information... PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Exemption of Records Systems Under the Privacy Act § 16.130 Exemption of Department of Justice Systems: Correspondence Management Systems for the Department...

Systems concepts: Lectures on contemporary approaches to systems.

NASA Technical Reports Server (NTRS)

Miles, R. F., Jr.

1973-01-01

Collection of papers dealing with the application of systems concepts to a wide range of disciplines. The topics include systems definitions and designs, models for systems engineering, the evolution of the JPL, systems concepts in lunar and planetary projects, civil systems projects, and Apollo program evaluation. Individual items are announced in this issue.

Commonsense System Pricing; Or, How Much Will that $1,200 Computer Really Cost?

ERIC Educational Resources Information Center

Crawford, Walt

1984-01-01

Three methods employed to price and sell computer equipment are discussed: computer pricing, hardware pricing, system pricing (system includes complete computer and support hardware system and relatively complete software package). Advantages of system pricing are detailed, the author's system is described, and 10 systems currently available are…

Thermal Distribution System | Energy Systems Integration Facility | NREL

Science.gov Websites

Thermal Distribution System Thermal Distribution System The Energy Systems Integration Facility's integrated thermal distribution system consists of a thermal water loop connected to a research boiler and . Photo of the roof of the Energy Systems Integration Facility. The thermal distribution bus allows

Application of the Doppler lidar system to agricultural burning and air-sea interactions

NASA Technical Reports Server (NTRS)

Fitzjarrald, D.

1980-01-01

The Doppler lidar system is potentially a very powerful measurement system. Three areas concerning the system are discussed: (1) error analysis of the system to verify the results; (2) application of the system to agricultural burning in California central valley; and (3) oceanographic possibilities of the system.

Asan medical information system for healthcare quality improvement.

PubMed

Ryu, Hyeon Jeong; Kim, Woo Sung; Lee, Jae Ho; Min, Sung Woo; Kim, Sun Ja; Lee, Yong Su; Lee, Young Ha; Nam, Sang Woo; Eo, Gi Seung; Seo, Sook Gyoung; Nam, Mi Hyun

2010-09-01

This purpose of this paper is to introduce the status of the Asan Medical Center (AMC) medical information system with respect to healthcare quality improvement. Asan Medical Information System (AMIS) is projected to become a completely electronic and digital information hospital. AMIS has played a role in improving the health care quality based on the following measures: safety, effectiveness, patient-centeredness, timeliness, efficiency, privacy, and security. AMIS CONSISTED OF SEVERAL DISTINCTIVE SYSTEMS: order communication system, electronic medical record, picture archiving communication system, clinical research information system, data warehouse, enterprise resource planning, IT service management system, and disaster recovery system. The most distinctive features of AMIS were the high alert-medication recognition & management system, the integrated and severity stratified alert system, the integrated patient monitoring system, the perioperative diabetic care monitoring and support system, and the clinical indicator management system. AMIS provides IT services for AMC, 7 affiliated hospitals and over 5,000 partners clinics, and was developed to improve healthcare services. The current challenge of AMIS is standard and interoperability. A global health IT strategy is needed to get through the current challenges and to provide new services as needed.

Corrective Action Plan for Corrective Action Unit 271: Areas 25, 26, and 27 Septic Systems, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. B. Jackson

2003-05-01

The Areas 25, 26 and 27 Septic Systems are in the Federal Facility Agreement and Consent Order (FFACO) of 1996 as Corrective Action Unit (CAU) 271. This Corrective Action Plan (CAP) provides selected corrective action alternatives and proposes the closure methodology for CAU 271. CAU 271 is located on the Nevada Test Site (NTS) approximately 105 kilometers (65 miles) northwest of Las Vegas, Nevada, and consists of the following 15 Corrective Action Sites (CAS): CAS 25-04-1, Septic System; CAS 25-04-03, Septic System; CAS25-04-04, Septic System; CAS 25-04-08, Septic System; CAS 25-04-09, Septic System; CAS 25-04-10, Septic System; CAS 25-04-11, Septicmore » System; CAS 26-03-01, Contaminated Water Reservoir; CAS 26-04-1, Septic System; CAS 26-04-02, Septic System; CAS 26-05-01, Radioactive Leachfield; CAS-26-05-03, Septic System; CAS 26-05-04, Septic System; CAS 26-05-05, Septic System; and CAS 27-05-02, Leachfield.« less

Design distributed simulation platform for vehicle management system

NASA Astrophysics Data System (ADS)

Wen, Zhaodong; Wang, Zhanlin; Qiu, Lihua

2006-11-01

Next generation military aircraft requires the airborne management system high performance. General modules, data integration, high speed data bus and so on are needed to share and manage information of the subsystems efficiently. The subsystems include flight control system, propulsion system, hydraulic power system, environmental control system, fuel management system, electrical power system and so on. The unattached or mixed architecture is changed to integrated architecture. That means the whole airborne system is regarded into one system to manage. So the physical devices are distributed but the system information is integrated and shared. The process function of each subsystem are integrated (including general process modules, dynamic reconfiguration), furthermore, the sensors and the signal processing functions are shared. On the other hand, it is a foundation for power shared. Establish a distributed vehicle management system using 1553B bus and distributed processors which can provide a validation platform for the research of airborne system integrated management. This paper establishes the Vehicle Management System (VMS) simulation platform. Discuss the software and hardware configuration and analyze the communication and fault-tolerant method.

UNIX-based operating systems robustness evaluation

NASA Technical Reports Server (NTRS)

Chang, Yu-Ming

1996-01-01

Robust operating systems are required for reliable computing. Techniques for robustness evaluation of operating systems not only enhance the understanding of the reliability of computer systems, but also provide valuable feed- back to system designers. This thesis presents results from robustness evaluation experiments on five UNIX-based operating systems, which include Digital Equipment's OSF/l, Hewlett Packard's HP-UX, Sun Microsystems' Solaris and SunOS, and Silicon Graphics' IRIX. Three sets of experiments were performed. The methodology for evaluation tested (1) the exception handling mechanism, (2) system resource management, and (3) system capacity under high workload stress. An exception generator was used to evaluate the exception handling mechanism of the operating systems. Results included exit status of the exception generator and the system state. Resource management techniques used by individual operating systems were tested using programs designed to usurp system resources such as physical memory and process slots. Finally, the workload stress testing evaluated the effect of the workload on system performance by running a synthetic workload and recording the response time of local and remote user requests. Moderate to severe performance degradations were observed on the systems under stress.

Implementation of Consolidated HIS: Improving Quality and Efficiency of Healthcare

PubMed Central

Choi, Jinwook; Seo, Jeong-Wook; Chung, Chun Kee; Kim, Kyung-Hwan; Kim, Ju Han; Kim, Jong Hyo; Chie, Eui Kyu; Cho, Hyun-Jai; Goo, Jin Mo; Lee, Hyuk-Joon; Wee, Won Ryang; Nam, Sang Mo; Lim, Mi-Sun; Kim, Young-Ah; Yang, Seung Hoon; Jo, Eun Mi; Hwang, Min-A; Kim, Wan Suk; Lee, Eun Hye; Choi, Su Hi

2010-01-01

Objectives Adoption of hospital information systems offers distinctive advantages in healthcare delivery. First, implementation of consolidated hospital information system in Seoul National University Hospital led to significant improvements in quality of healthcare and efficiency of hospital management. Methods The hospital information system in Seoul National University Hospital consists of component applications: clinical information systems, clinical research support systems, administrative information systems, management information systems, education support systems, and referral systems that operate to generate utmost performance when delivering healthcare services. Results Clinical information systems, which consist of such applications as electronic medical records, picture archiving and communication systems, primarily support clinical activities. Clinical research support system provides valuable resources supporting various aspects of clinical activities, ranging from management of clinical laboratory tests to establishing care-giving procedures. Conclusions Seoul National University Hospital strives to move its hospital information system to a whole new level, which enables customized healthcare service and fulfills individual requirements. The current information strategy is being formulated as an initial step of development, promoting the establishment of next-generation hospital information system. PMID:21818449

Experiences with establishing and implementing learning management system and computer-based test system in medical college.

PubMed

Park, Joo Hyun; Son, Ji Young; Kim, Sun

2012-09-01

The purpose of this study was to establish an e-learning system to support learning in medical education and identify solutions for improving the system. A learning management system (LMS) and computer-based test (CBT) system were established to support e-learning for medical students. A survey of 219 first- and second-grade medical students was administered. The questionnaire included 9 forced choice questions about the usability of system and 2 open-ended questions about necessary improvements to the system. The LMS consisted of a class management, class evaluation, and class attendance system. CBT consisted of a test management, item bank, and authoring tool system. The results of the survey showed a high level of satisfaction in all system usability items except for stability. Further, the advantages of the e-learning system were ensuring information accessibility, providing constant feedback, and designing an intuitive interface. Necessary improvements to the system were stability, user control, readability, and diverse device usage. Based on the findings, suggestions for developing an e-learning system to improve usability by medical students and support learning effectively are recommended.

Geographic information system development in the CARETS project

USGS Publications Warehouse

Mitchell, William B.; Fegeas, Robin G.; Fitzpatrick, Katherine A.; Hallam, Cheryl A.

1977-01-01

Experience in the development of a geographic information system to support the CARETS project has confirmed the considerable advantages that may accrue by paralleling the system development with a rational and balanced system production effort which permits the integration of the education and training of users with interim deliverable products to them. Those advantages include support for a long-term staff plan that recognizes substantial staff changes through system development and implementation, a fiscal plan that provides continuity in resources necessary for total system development, and a feedback system which allows the user to communicate his experiences in using the system. Thus far balance between system development and system production has not been achieved because of continuing large-scale spatial data processing requirements coupled with strong and insistent demands from users for immediately deliverable products from the system. That imbalance has refocussed staffing and fiscal plans from long-term system development to short- and near-term production requirements, continuously extends total system development time, and increases the possibility that later system development may reduce the usefulness of current interim products.

Doctors' use of electronic medical records systems in hospitals: cross sectional survey

PubMed Central

Lærum, Hallvard; Ellingsen, Gunnar; Faxvaag, Arild

2001-01-01

Objectives To compare the use of three electronic medical records systems by doctors in Norwegian hospitals for general clinical tasks. Design Cross sectional questionnaire survey. Semistructured telephone interviews with key staff in information technology in each hospital for details of local implementation of the systems. Setting 32 hospital units in 19 Norwegian hospitals with electronic medical records systems. Participants 227 (72%) of 314 hospital doctors responded, equally distributed between the three electronic medical records systems. Main outcome measures Proportion of respondents who used the electronic system, calculated for each of 23 tasks; difference in proportions of users of different systems when functionality of systems was similar. Results Most tasks listed in the questionnaire (15/23) were generally covered with implemented functions in the electronic medical records systems. However, the systems were used for only 2-7 of the tasks, mainly associated with reading patient data. Respondents showed significant differences in frequency of use of the different systems for four tasks for which the systems offered equivalent functionality. The respondents scored highly in computer literacy (72.2/100), and computer use showed no correlation with respondents' age, sex, or work position. User satisfaction scores were generally positive (67.2/100), with some difference between the systems. Conclusions Doctors used electronic medical records systems for far fewer tasks than the systems supported. What is already known on this topicElectronic information systems in health care have not undergone systematic evaluation, and few comparisons between electronic medical records systems have been madeGiven the information intensive nature of clinical work, electronic medical records systems should be of help to doctors for most clinical tasksWhat this study addsDoctors in Norwegian hospitals reported a low level of use of all electronic medical records systemsThe systems were mainly used for reading patient data, and doctors used the systems for less than half of the tasks for which the systems were functionalAnalyses of actual use of electronic medical records provide more information than user satisfaction or functionality of such records systems PMID:11739222

WASTE PACKAGE REMEDIATION SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

N.D. Sudan

2000-06-22

The Waste Package Remediation System remediates waste packages (WPs) and disposal containers (DCs) in one of two ways: preparation of rejected DC closure welds for repair or opening of the DC/WP. DCs are brought to the Waste Package Remediation System for preparation of rejected closure welds if testing of the closure weld by the Disposal Container Handling System indicates an unacceptable, but repairable, welding flaw. DC preparation of rejected closure welds will require removal of the weld in such a way that the Disposal Container Handling System may resume and complete the closure welding process. DCs/WPs are brought to themore » Waste Package Remediation System for opening if the Disposal Container Handling System testing of the DC closure weld indicates an unrepairable welding flaw, or if a WP is recovered from the subsurface repository because suspected damage to the WP or failure of the WP has occurred. DC/WP opening will require cutting of the DC/WP such that a temporary seal may be installed and the waste inside the DC/WP removed by another system. The system operates in a Waste Package Remediation System hot cell located in the Waste Handling Building that has direct access to the Disposal Container Handling System. One DC/WP at a time can be handled in the hot cell. The DC/WP arrives on a transfer cart, is positioned within the cell for system operations, and exits the cell without being removed from the cart. The system includes a wide variety of remotely operated components including a manipulator with hoist and/or jib crane, viewing systems, machine tools for opening WPs, and equipment used to perform pressure and gas composition sampling. Remotely operated equipment is designed to facilitate DC/WP decontamination and hot cell equipment maintenance, and interchangeable components are provided where appropriate. The Waste Package Remediation System interfaces with the Disposal Container Handling System for the receipt and transport of WPs and DCs. The Waste Handling Building System houses the system, and provides the facility, safety, and auxiliary systems required to support operations. The system receives power from the Waste Handling Building Electrical System. The system also interfaces with the various DC systems.« less

Space station integrated propulsion and fluid system study: Fluid systems configuration databook

NASA Technical Reports Server (NTRS)

Rose, L.; Bicknell, B.; Bergman, D.; Wilson, S.

1987-01-01

This databook contains fluid system requirements and system descriptions for Space Station program elements including the United States and International modules, integrated fluid systems, attached payloads, fluid servicers and vehicle accommodation facilities. Separate sections are devoted to each of the program elements and include a discussion of the overall system requirements, specific fluid systems requirements and systems descriptions. The systems descriptions contain configurations, fluid inventory data and component lists. In addition, a list of information sources is referenced at the end of each section.

System performance testing of the DSN radio science system, Mark 3-78

NASA Technical Reports Server (NTRS)

Berman, A. L.; Mehta, J. S.

1978-01-01

System performance tests are required to evaluate system performance following initial system implementation and subsequent modification, and to validate system performance prior to actual operational usage. Non-real-time end-to-end Radio Science system performance tests are described that are based on the comparison of open-loop radio science data to equivalent closed-loop radio metric data, as well as an abbreviated Radio Science real-time system performance test that validates critical Radio Science System elements at the Deep Space Station prior to actual operational usage.

Networked control of microgrid system of systems

NASA Astrophysics Data System (ADS)

Mahmoud, Magdi S.; Rahman, Mohamed Saif Ur; AL-Sunni, Fouad M.

2016-08-01

The microgrid has made its mark in distributed generation and has attracted widespread research. However, microgrid is a complex system which needs to be viewed from an intelligent system of systems perspective. In this paper, a network control system of systems is designed for the islanded microgrid system consisting of three distributed generation units as three subsystems supplying a load. The controller stabilises the microgrid system in the presence of communication infractions such as packet dropouts and delays. Simulation results are included to elucidate the effectiveness of the proposed control strategy.

Fission Technology for Exploring and Utilizing the Solar System

NASA Technical Reports Server (NTRS)

Houts, Mike; VanDyke, Melissa; Godfroy, Tom; Pedersen, Kevin; Martin, James; Dickens, Ricky; Salvail, Pat; Hrbub, Ivana; Schmidt, George R. (Technical Monitor)

2000-01-01

Fission technology can enable rapid, affordable access to any point in the solar system. Potential fission-based transportation options include bimodal nuclear thermal rockets, high specific energy propulsion systems, and pulsed fission propulsion systems. In-space propellant re-supply enhances the effective performance of all systems, but requires significant infrastructure development. Safe, timely, affordable utilization of first-generation space fission propulsion systems will enable the development of more advanced systems. First generation space systems will build on over 45 years of US and international space fission system technology development to minimize cost,

An hierarchical approach to performance evaluation of expert systems

NASA Technical Reports Server (NTRS)

Dominick, Wayne D. (Editor); Kavi, Srinu

1985-01-01

The number and size of expert systems is growing rapidly. Formal evaluation of these systems - which is not performed for many systems - increases the acceptability by the user community and hence their success. Hierarchical evaluation that had been conducted for computer systems is applied for expert system performance evaluation. Expert systems are also evaluated by treating them as software systems (or programs). This paper reports many of the basic concepts and ideas in the Performance Evaluation of Expert Systems Study being conducted at the University of Southwestern Louisiana.

Liquid and Gaseous Waste Operations Department annual operating report CY 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maddox, J.J.; Scott, C.B.

1997-03-01

This annual report summarizes operating activities dealing with the process waste system, the liquid low-level waste system, and the gaseous waste system. It also describes upgrade activities dealing with the process and liquid low-level waste systems, the cathodic protection system, a stack ventilation system, and configuration control. Maintenance activities are described dealing with nonradiological wastewater treatment plant, process waste treatment plant and collection system, liquid low-level waste system, and gaseous waste system. Miscellaneous activities include training, audits/reviews/tours, and environmental restoration support.

Sunlight supply and gas exchange systems in microalgal bioreactor

NASA Technical Reports Server (NTRS)

Mori, K.; Ohya, H.; Matsumoto, K.; Furune, H.

1987-01-01

The bioreactor with sunlight supply system and gas exchange systems presented has proved feasible in ground tests and shows much promise for space use as a closed ecological life support system device. The chief conclusions concerning the specification of total system needed for a life support system for a man in a space station are the following: (1) Sunlight supply system - compactness and low electrical consumption; (2) Bioreactor system - high density and growth rate of chlorella; and (3) Gas exchange system - enough for O2 production and CO2 assimilation.

Smart information system for gachon university gil hospital.

PubMed

Park, Dong Kyun; Jung, Eun Young; Jeong, Byung Hui; Moon, Byung Chan; Kang, Hyung Wook; Tchah, Hann; Han, Gi Seong; Cheng, Woo Sung; Lee, Young Ho

2012-03-01

In this research, the hospital information system of Gachon University Gil hospital is introduced and a future strategy for hospital information systems is proposed. This research introduces the development conditions of hospital information system at Gachon University Gil hospital, information about the development of the enterprise resource planning (ERP), a medical service process improvement system, and the personal health record (PHR) system. The medical service process and work efficiency were improved through the medical service process improvement system, which is the most common hospital information system at Gachon University Gil hospital and which includes an emergency medical service system, an online evaluation system and a round support system. Gachon University Gil hospital developed medical service improvement systems to increase work efficiency of medical team and optimized the systems to prove the availability of high-quality medical services for patients and their families. The PHR-based personalized health care solution is under development and will provide higher quality medical service for more patients in the future.

Reliability and performance evaluation of systems containing embedded rule-based expert systems

NASA Technical Reports Server (NTRS)

Beaton, Robert M.; Adams, Milton B.; Harrison, James V. A.

1989-01-01

A method for evaluating the reliability of real-time systems containing embedded rule-based expert systems is proposed and investigated. It is a three stage technique that addresses the impact of knowledge-base uncertainties on the performance of expert systems. In the first stage, a Markov reliability model of the system is developed which identifies the key performance parameters of the expert system. In the second stage, the evaluation method is used to determine the values of the expert system's key performance parameters. The performance parameters can be evaluated directly by using a probabilistic model of uncertainties in the knowledge-base or by using sensitivity analyses. In the third and final state, the performance parameters of the expert system are combined with performance parameters for other system components and subsystems to evaluate the reliability and performance of the complete system. The evaluation method is demonstrated in the context of a simple expert system used to supervise the performances of an FDI algorithm associated with an aircraft longitudinal flight-control system.

Smart Information System for Gachon University Gil Hospital

PubMed Central

Jung, Eun Young; Jeong, Byung Hui; Moon, Byung Chan; Kang, Hyung Wook; Tchah, Hann; Han, Gi Seong; Cheng, Woo Sung; Lee, Young Ho

2012-01-01

Objectives In this research, the hospital information system of Gachon University Gil hospital is introduced and a future strategy for hospital information systems is proposed. Methods This research introduces the development conditions of hospital information system at Gachon University Gil hospital, information about the development of the enterprise resource planning (ERP), a medical service process improvement system, and the personal health record (PHR) system. Results The medical service process and work efficiency were improved through the medical service process improvement system, which is the most common hospital information system at Gachon University Gil hospital and which includes an emergency medical service system, an online evaluation system and a round support system. Conclusions Gachon University Gil hospital developed medical service improvement systems to increase work efficiency of medical team and optimized the systems to prove the availability of high-quality medical services for patients and their families. The PHR-based personalized health care solution is under development and will provide higher quality medical service for more patients in the future. PMID:22509476

Vehicle Maximum Weight Limitation Based on Intelligent Weight Sensor

NASA Astrophysics Data System (ADS)

Raihan, W.; Tessar, R. M.; Ernest, C. O. S.; E Byan, W. R.; Winda, A.

2017-03-01

Vehicle weight is an important factor to be maintained for transportation safety. A weight limitation system is proposed to make sure the vehicle weight is always below its designation prior the vehicle is being used by the driver. The proposed system is divided into two systems, namely vehicle weight confirmation system and weight warning system. In vehicle weight confirmation system, the weight sensor work for the first time after the ignition switch is turned on. When the weight is under the weight limit, the starter engine can be switched on to start the engine system, otherwise it will be locked. The seconds system, will operated after checking all the door at close position, once the door of the car is closed, the weight warning system will check once again the weight during runing engine condition. The results of these two systems, vehicle weight confirmation system and weight warning system have 100 % accuracy, respectively. These show that the proposed vehicle weight limitation system operate well.

Exploration Medical System Technical Architecture Overview

NASA Technical Reports Server (NTRS)

Cerro, J.; Rubin, D.; Mindock, J.; Middour, C.; McGuire, K.; Hanson, A.; Reilly, J.; Burba, T.; Urbina, M.

2018-01-01

The Exploration Medical Capability (ExMC) Element Systems Engineering (SE) goals include defining the technical system needed to support medical capabilities for a Mars exploration mission. A draft medical system architecture was developed based on stakeholder needs, system goals, and system behaviors, as captured in an ExMC concept of operations document and a system model. This talk will discuss a high-level view of the medical system, as part of a larger crew health and performance system, both of which will support crew during Deep Space Transport missions. Other mission components, such as the flight system, ground system, caregiver, and patient, will be discussed as aspects of the context because the medical system will have important interactions with each. Additionally, important interactions with other aspects of the crew health and performance system are anticipated, such as health & wellness, mission task performance support, and environmental protection. This talk will highlight areas in which we are working with other disciplines to understand these interactions.

MARBLE: A system for executing expert systems in parallel

NASA Technical Reports Server (NTRS)

Myers, Leonard; Johnson, Coe; Johnson, Dean

1990-01-01

This paper details the MARBLE 2.0 system which provides a parallel environment for cooperating expert systems. The work has been done in conjunction with the development of an intelligent computer-aided design system, ICADS, by the CAD Research Unit of the Design Institute at California Polytechnic State University. MARBLE (Multiple Accessed Rete Blackboard Linked Experts) is a system of C Language Production Systems (CLIPS) expert system tool. A copied blackboard is used for communication between the shells to establish an architecture which supports cooperating expert systems that execute in parallel. The design of MARBLE is simple, but it provides support for a rich variety of configurations, while making it relatively easy to demonstrate the correctness of its parallel execution features. In its most elementary configuration, individual CLIPS expert systems execute on their own processors and communicate with each other through a modified blackboard. Control of the system as a whole, and specifically of writing to the blackboard is provided by one of the CLIPS expert systems, an expert control system.

Highlights of recent balance of system research and evaluation

NASA Astrophysics Data System (ADS)

Thomas, M. G.; Stevens, J. W.

The cost of most photovoltaic (PV) systems is more a function of the balance of system (BOS) components than the collectors. The exception to this rule is the grid-tied system whose cost is related more directly to the collectors, and secondarily to the inverter/controls. In fact, recent procurements throughout the country document that collector costs for roof-mounted, utility-tied systems (Russell, PV Systems Workshop, 7/94) represent 60% to 70% of the system cost. This contrasts with the current market for packaged stand-alone all PV or PV-hybrid systems where collectors represent only 25% to 35% of the total. Not only are the BOS components the cost drivers in the current cost-effective PV system market place, they are also the least reliable components. This paper discusses the impact that BOS issues have on component performance, system performance, and system cost and reliability. We will also look at recent recommended changes in system design based upon performance evaluations of fielded PV systems.

A fuzzy classifier system for process control

NASA Technical Reports Server (NTRS)

Karr, C. L.; Phillips, J. C.

1994-01-01

A fuzzy classifier system that discovers rules for controlling a mathematical model of a pH titration system was developed by researchers at the U.S. Bureau of Mines (USBM). Fuzzy classifier systems successfully combine the strengths of learning classifier systems and fuzzy logic controllers. Learning classifier systems resemble familiar production rule-based systems, but they represent their IF-THEN rules by strings of characters rather than in the traditional linguistic terms. Fuzzy logic is a tool that allows for the incorporation of abstract concepts into rule based-systems, thereby allowing the rules to resemble the familiar 'rules-of-thumb' commonly used by humans when solving difficult process control and reasoning problems. Like learning classifier systems, fuzzy classifier systems employ a genetic algorithm to explore and sample new rules for manipulating the problem environment. Like fuzzy logic controllers, fuzzy classifier systems encapsulate knowledge in the form of production rules. The results presented in this paper demonstrate the ability of fuzzy classifier systems to generate a fuzzy logic-based process control system.

Flight control system design factors for applying automated testing techniques

NASA Technical Reports Server (NTRS)

Sitz, Joel R.; Vernon, Todd H.

1990-01-01

The principal design features and operational experiences of the X-29 forward-swept-wing aircraft and F-18 high alpha research vehicle (HARV) automated test systems are discussed. It is noted that operational experiences in developing and using these automated testing techniques have highlighted the need for incorporating target system features to improve testability. Improved target system testability can be accomplished with the addition of nonreal-time and real-time features. Online access to target system implementation details, unobtrusive real-time access to internal user-selectable variables, and proper software instrumentation are all desirable features of the target system. Also, test system and target system design issues must be addressed during the early stages of the target system development. Processing speeds of up to 20 million instructions/s and the development of high-bandwidth reflective memory systems have improved the ability to integrate the target system and test system for the application of automated testing techniques. It is concluded that new methods of designing testability into the target systems are required.

Development of a model protection and dynamic response monitoring system for the national transonic facility

NASA Technical Reports Server (NTRS)

Young, Clarence P., Jr.; Balakrishna, S.; Kilgore, W. Allen

1995-01-01

A state-of-the-art, computerized mode protection and dynamic response monitoring system has been developed for the NASA Langley Research Center National Transonic Facility (NTF). This report describes the development of the model protection and shutdown system (MPSS). A technical description of the system is given along with discussions on operation and capabilities of the system. Applications of the system to vibration problems are presented to demonstrate the system capabilities, typical applications, versatility, and investment research return derived from the system to date. The system was custom designed for the NTF but can be used at other facilities or for other dynamic measurement/diagnostic applications. Potential commercial uses of the system are described. System capability has been demonstrated for forced response testing and for characterizing and quantifying bias errors for onboard inertial model attitude measurement devices. The system is installed in the NTF control room and has been used successfully for monitoring, recording and analyzing the dynamic response of several model systems tested in the NTF.

Evaluation of health information systems research in information systems research: A meta-analysis.

PubMed

Haried, Peter; Claybaugh, Craig; Dai, Hua

2017-04-01

Given the importance of the health-care industry and the promise of health information systems, researchers are encouraged to build on the shoulders of giants as the saying goes. The health information systems field has a unique opportunity to learn from and extend the work that has already been done by the highly correlated information systems field. As a result, this research article presents a past, present and future meta-analysis of health information systems research in information systems journals over the 2000-2015 time period. Our analysis reviewed 126 articles on a variety of topics related to health information systems research published in the "Senior Scholars" list of the top eight ranked information systems academic journals. Across the selected information systems academic journals, our findings compare research methodologies applied, health information systems topic areas investigated and research trends. Interesting results emerge in the range and evolution of health information systems research and opportunities for health information systems researchers and practitioners to consider moving forward.

Food System Trade Study for a Near-Term Mars Mission

NASA Technical Reports Server (NTRS)

Levri, Julie; Luna, Bernadette (Technical Monitor)

2000-01-01

This paper evaluates several food system options for a near-term Mars mission, based on plans for the 120-day BIO-Plex test. Food systems considered in the study are based on the International Space Station (ISS) Assembly Phase and Assembly Complete food systems. The four systems considered are: 1) ISS assembly phase food system (US portion) with individual packaging without salad production; 2) ISS assembly phase food system (US portion) with individual packaging, with salad production; 3) ISS assembly phase food system (US portion) with bulk packaging, with salad production; 4) ISS assembly complete food system (US portion) with bulk packaging with salad and refrigeration/freezing. The food system options are assessed using equivalent system mass (ESM), which evaluates each option based upon the mass, volume, power, cooling and crewtime requirements that are associated with each food system option. However, since ESM is unable to elucidate the differences in psychological benefits between the food systems, a qualitative evaluation of each option is also presented.

Benchmarking the performance of fixed-image receptor digital radiography systems. Part 2: system performance metric.

PubMed

Lee, Kam L; Bernardo, Michael; Ireland, Timothy A

2016-06-01

This is part two of a two-part study in benchmarking system performance of fixed digital radiographic systems. The study compares the system performance of seven fixed digital radiography systems based on quantitative metrics like modulation transfer function (sMTF), normalised noise power spectrum (sNNPS), detective quantum efficiency (sDQE) and entrance surface air kerma (ESAK). It was found that the most efficient image receptors (greatest sDQE) were not necessarily operating at the lowest ESAK. In part one of this study, sMTF is shown to depend on system configuration while sNNPS is shown to be relatively consistent across systems. Systems are ranked on their signal-to-noise ratio efficiency (sDQE) and their ESAK. Systems using the same equipment configuration do not necessarily have the same system performance. This implies radiographic practice at the site will have an impact on the overall system performance. In general, systems are more dose efficient at low dose settings.

Formal Integrals and Noether Operators of Nonlinear Hyperbolic Partial Differential Systems Admitting a Rich Set of Symmetries

NASA Astrophysics Data System (ADS)

Startsev, Sergey Ya.

2017-05-01

The paper is devoted to hyperbolic (generally speaking, non-Lagrangian and nonlinear) partial differential systems possessing a full set of differential operators that map any function of one independent variable into a symmetry of the corresponding system. We demonstrate that a system has the above property if and only if this system admits a full set of formal integrals (i.e., differential operators which map symmetries into integrals of the system). As a consequence, such systems possess both direct and inverse Noether operators (in the terminology of a work by B. Fuchssteiner and A.S. Fokas who have used these terms for operators that map cosymmetries into symmetries and perform transformations in the opposite direction). Systems admitting Noether operators are not exhausted by Euler-Lagrange systems and the systems with formal integrals. In particular, a hyperbolic system admits an inverse Noether operator if a differential substitution maps this system into a system possessing an inverse Noether operator.

Description of the SSF PMAD DC testbed control system data acquisition function

NASA Technical Reports Server (NTRS)

Baez, Anastacio N.; Mackin, Michael; Wright, Theodore

1992-01-01

The NASA LeRC in Cleveland, Ohio has completed the development and integration of a Power Management and Distribution (PMAD) DC Testbed. This testbed is a reduced scale representation of the end to end, sources to loads, Space Station Freedom Electrical Power System (SSF EPS). This unique facility is being used to demonstrate DC power generation and distribution, power management and control, and system operation techniques considered to be prime candidates for the Space Station Freedom. A key capability of the testbed is its ability to be configured to address system level issues in support of critical SSF program design milestones. Electrical power system control and operation issues like source control, source regulation, system fault protection, end-to-end system stability, health monitoring, resource allocation, and resource management are being evaluated in the testbed. The SSF EPS control functional allocation between on-board computers and ground based systems is evolving. Initially, ground based systems will perform the bulk of power system control and operation. The EPS control system is required to continuously monitor and determine the current state of the power system. The DC Testbed Control System consists of standard controllers arranged in a hierarchical and distributed architecture. These controllers provide all the monitoring and control functions for the DC Testbed Electrical Power System. Higher level controllers include the Power Management Controller, Load Management Controller, Operator Interface System, and a network of computer systems that perform some of the SSF Ground based Control Center Operation. The lower level controllers include Main Bus Switch Controllers and Photovoltaic Controllers. Power system status information is periodically provided to the higher level controllers to perform system control and operation. The data acquisition function of the control system is distributed among the various levels of the hierarchy. Data requirements are dictated by the control system algorithms being implemented at each level. A functional description of the various levels of the testbed control system architecture, the data acquisition function, and the status of its implementationis presented.

SYSTEMS BIOLOGY MODEL DEVELOPMENT AND APPLICATION

EPA Science Inventory

System biology models holistically describe, in a quantitative fashion, the relationships between different levels of a biologic system. Relationships between individual components of a system are delineated. System biology models describe how the components of the system inter...

Monitoring of GPS(Global Positioning System) System Performance

DOT National Transportation Integrated Search

1985-06-01

The Global Positioning System (GPS), a worldwide satellite-based navigation system developed by the Department of Defense, is scheduled to become operational in late 1988. The system has the potential to become the primary radionaviagation system for...

Resource loading system and method for use in atmosphere-containment scenarios

DOEpatents

Dilday, Jr., Daniel R.; Reyes, Roberto; Weidmeyer, Stanley

2017-09-12

The invention provides a system for preventing fluid exchange between the interior and exterior of containment enclosures such as process-, hazard-, and research-enclosure systems generally, gloveboxes, containment systems, isolation systems, confinement systems, cleanrooms, negative air systems, and positive air system areas while simultaneously providing material transfer into and out of the enclosures. The invention also provides a method for transporting material into or out of a containment structure.

Modular Simulator System (MSS). System/Segment Specification for the Generic MSS - System Integration. Volume 1

DTIC Science & Technology

1993-08-20

UNLIMITED. SYSTEMS ENGINEERING DIVISION AERONAUTICAL SYSTEMS CENTER AIR FORCE MATERIEL COMMAND WRIGHT PATTERSON AFB OH 45433-7126 YOITCE When Government...BASINGER Progatl anager Team Leader Special Programs Divsion Special Programs Division JAMES J. O’CONNELL Chief, Systems Engineering Division Training...ADDRESS(ES) 10. SPONSORING/ MONITORING AGENCY REPORT NUMBER Aeronautical Systems Center Systems Engineering Division ASC-TR-94-50 10 Bldg 11 2240 B St

Utilization of Internet Protocol-Based Voice Systems in Remote Payload Operations

NASA Technical Reports Server (NTRS)

Best, Susan; Nichols, Kelvin; Bradford, Robert

2003-01-01

This viewgraph presentation provides an overview of a proposed voice communication system for use in remote payload operations performed on the International Space Station. The system, Internet Voice Distribution System (IVoDS), would make use of existing Internet protocols, and offer a number of advantages over the system currently in use. Topics covered include: system description and operation, system software and hardware, system architecture, project status, and technology transfer applications.

Application of adaptive antenna techniques to future commercial satellite communication

NASA Technical Reports Server (NTRS)

Ersoy, L.; Lee, E. A.; Matthews, E. W.

1987-01-01

The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further sub-divided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

Application of adaptive antenna techniques to future commercial satellite communications. Executive summary

NASA Technical Reports Server (NTRS)

Ersoy, L.; Lee, E. A.; Matthews, E. W.

1987-01-01

The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further subdivided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

AIAA/NASA International Symposium on Space Information Systems, 2nd, Pasadena, CA, Sept. 17-19, 1990, Proceedings. Vols. 1 & 2

NASA Technical Reports Server (NTRS)

Tavenner, Leslie A. (Editor)

1991-01-01

These proceedings overview major space information system projects and lessons learned from current missions. Other topics include the science information system requirements for the 1990s, an information systems design approach for major programs, the technology needs and projections, the standards for space data information systems, the artificial intelligence technology and applications, international interoperability, and spacecraft data systems and architectures advanced communications. Other topics include the software engineering technology and applications, the multimission multidiscipline information system architectures, the distributed planning and scheduling systems and operations, and the computer and information systems architectures. Paper presented include prospects for scientific data analysis systems for solar-terrestrial physics in the 1990s, the Columbus data management system, data storage technologies for the future, the German aerospace research establishment, and launching artificial intelligence in NASA ground systems.

Mechanization of and experience with a triplex fly-by-wire backup control system

NASA Technical Reports Server (NTRS)

Lock, W. P.; Petersen, W. R.; Whitman, G. B.

1976-01-01

A redundant three axis analog control system was designed and developed to back up a digital fly by wire control system for an F-8C airplane. The mechanization and operational experience with the backup control system, the problems involved in synchronizing it with the primary system, and the reliability of the system are discussed. The backup control system was dissimilar to the primary system, and it provided satisfactory handling through the flight envelope evaluated. Limited flight tests of a variety of control tasks showed that control was also satisfactory when the backup control system was controlled by a minimum displacement (force) side stick. The operational reliability of the F-8 digital fly by wire control system was satisfactory, with no unintentional downmodes to the backup control system in flight. The ground and flight reliability of the system's components is discussed.

Nursing home costs, Medicaid rates, and profits under alternative Medicaid payment systems.

PubMed Central

Schlenker, R E

1991-01-01

This analysis compares nursing home costs, Medicaid payment rates, and profits under three Medicaid nursing home payment systems: case-mix, facility-specific, and class-rate systems. Data used were collected from 135 nursing homes in seven states. The association of case mix with costs, rates, and profits under the three payment systems was of particular interest. Case mix was more strongly associated (positively) with patient care cost and the Medicaid rate for the case-mix systems than for the other systems, particularly the class-rate systems. In contrast, case mix and profits were not associated in the case-mix or facility-specific systems, but were negatively associated in the class rate systems. Overall, the results suggest that case-mix systems have some important advantages over other payment systems, but further research is needed on larger samples and involving the newer case-mix systems. PMID:1743972

Mathematical structure of unit systems

NASA Astrophysics Data System (ADS)

Kitano, Masao

2013-05-01

We investigate the mathematical structure of unit systems and the relations between them. Looking over the entire set of unit systems, we can find a mathematical structure that is called preorder (or quasi-order). For some pair of unit systems, there exists a relation of preorder such that one unit system is transferable to the other unit system. The transfer (or conversion) is possible only when all of the quantities distinguishable in the latter system are always distinguishable in the former system. By utilizing this structure, we can systematically compare the representations in different unit systems. Especially, the equivalence class of unit systems (EUS) plays an important role because the representations of physical quantities and equations are of the same form in unit systems belonging to an EUS. The dimension of quantities is uniquely defined in each EUS. The EUS's form a partially ordered set. Using these mathematical structures, unit systems and EUS's are systematically classified and organized as a hierarchical tree.

Controlled cooling of an electronic system for reduced energy consumption

DOE Office of Scientific and Technical Information (OSTI.GOV)

David, Milnes P.; Iyengar, Madhusudan K.; Schmidt, Roger R.

Energy efficient control of a cooling system cooling an electronic system is provided. The control includes automatically determining at least one adjusted control setting for at least one adjustable cooling component of a cooling system cooling the electronic system. The automatically determining is based, at least in part, on power being consumed by the cooling system and temperature of a heat sink to which heat extracted by the cooling system is rejected. The automatically determining operates to reduce power consumption of the cooling system and/or the electronic system while ensuring that at least one targeted temperature associated with the coolingmore » system or the electronic system is within a desired range. The automatically determining may be based, at least in part, on one or more experimentally obtained models relating the targeted temperature and power consumption of the one or more adjustable cooling components of the cooling system.« less

National launch strategy vehicle data management system

NASA Technical Reports Server (NTRS)

Cordes, David

1990-01-01

The national launch strategy vehicle data management system (NLS/VDMS) was developed as part of the 1990 NASA Summer Faculty Fellowship Program. The system was developed under the guidance of the Engineering Systems Branch of the Information Systems Office, and is intended for use within the Program Development Branch PD34. The NLS/VDMS is an on-line database system that permits the tracking of various launch vehicle configurations within the program development office. The system is designed to permit the definition of new launch vehicles, as well as the ability to display and edit existing launch vehicles. Vehicles can be grouped in logical architectures within the system. Reports generated from this package include vehicle data sheets, architecture data sheets, and vehicle flight rate reports. The topics covered include: (1) system overview; (2) initial system development; (3) supercard hypermedia authoring system; (4) the ORACLE database; and (5) system evaluation.

Feasibility study of an Integrated Program for Aerospace vehicle Design (IPAD). Volume 4: IPAD system design

NASA Technical Reports Server (NTRS)

Goldfarb, W.; Carpenter, L. C.; Redhed, D. D.; Hansen, S. D.; Anderson, L. O.; Kawaguchi, A. S.

1973-01-01

The computing system design of IPAD is described and the requirements which form the basis for the system design are discussed. The system is presented in terms of a functional design description and technical design specifications. The functional design specifications give the detailed description of the system design using top-down structured programming methodology. Human behavioral characteristics, which specify the system design at the user interface, security considerations, and standards for system design, implementation, and maintenance are also part of the technical design specifications. Detailed specifications of the two most common computing system types in use by the major aerospace companies which could support the IPAD system design are presented. The report of a study to investigate migration of IPAD software between the two candidate 3rd generation host computing systems and from these systems to a 4th generation system is included.

Precision digital control systems

NASA Astrophysics Data System (ADS)

Vyskub, V. G.; Rozov, B. S.; Savelev, V. I.

This book is concerned with the characteristics of digital control systems of great accuracy. A classification of such systems is considered along with aspects of stabilization, programmable control applications, digital tracking systems and servomechanisms, and precision systems for the control of a scanning laser beam. Other topics explored are related to systems of proportional control, linear devices and methods for increasing precision, approaches for further decreasing the response time in the case of high-speed operation, possibilities for the implementation of a logical control law, and methods for the study of precision digital control systems. A description is presented of precision automatic control systems which make use of electronic computers, taking into account the existing possibilities for an employment of computers in automatic control systems, approaches and studies required for including a computer in such control systems, and an analysis of the structure of automatic control systems with computers. Attention is also given to functional blocks in the considered systems.

Designing an architectural style for Pervasive Healthcare systems.

PubMed

Rafe, Vahid; Hajvali, Masoumeh

2013-04-01

Nowadays, the Pervasive Healthcare (PH) systems are considered as an important research area. These systems have a dynamic structure and configuration. Therefore, an appropriate method for designing such systems is necessary. The Publish/Subscribe Architecture (pub/sub) is one of the convenient architectures to support such systems. PH systems are safety critical; hence, errors can bring disastrous results. To prevent such problems, a powerful analytical tool is required. So using a proper formal language like graph transformation systems for developing of these systems seems necessary. But even if software engineers use such high level methodologies, errors may occur in the system under design. Hence, it should be investigated automatically and formally that whether this model of system satisfies all their requirements or not. In this paper, a dynamic architectural style for developing PH systems is presented. Then, the behavior of these systems is modeled and evaluated using GROOVE toolset. The results of the analysis show its high reliability.

Modeling Complex Cross-Systems Software Interfaces Using SysML

NASA Technical Reports Server (NTRS)

Mandutianu, Sanda; Morillo, Ron; Simpson, Kim; Liepack, Otfrid; Bonanne, Kevin

2013-01-01

The complex flight and ground systems for NASA human space exploration are designed, built, operated and managed as separate programs and projects. However, each system relies on one or more of the other systems in order to accomplish specific mission objectives, creating a complex, tightly coupled architecture. Thus, there is a fundamental need to understand how each system interacts with the other. To determine if a model-based system engineering approach could be utilized to assist with understanding the complex system interactions, the NASA Engineering and Safety Center (NESC) sponsored a task to develop an approach for performing cross-system behavior modeling. This paper presents the results of applying Model Based Systems Engineering (MBSE) principles using the System Modeling Language (SysML) to define cross-system behaviors and how they map to crosssystem software interfaces documented in system-level Interface Control Documents (ICDs).

Low cost solar array project silicon materials task. Development of a process for high capacity arc heater production of silicon for solar arrays

NASA Technical Reports Server (NTRS)

Fey, M. G.

1981-01-01

The experimental verification system for the production of silicon via the arc heater-sodium reduction of SiCl4 was designed, fabricated, installed, and operated. Each of the attendant subsystems was checked out and operated to insure performance requirements. These subsystems included: the arc heaters/reactor, cooling water system, gas system, power system, Control & Instrumentation system, Na injection system, SiCl4 injection system, effluent disposal system and gas burnoff system. Prior to introducing the reactants (Na and SiCl4) to the arc heater/reactor, a series of gas only-power tests was conducted to establish the operating parameters of the three arc heaters of the system. Following the successful completion of the gas only-power tests and the readiness tests of the sodium and SiCl4 injection systems, a shakedown test of the complete experimental verification system was conducted.

Automatic system of collection of parameters and control of receiving equipment of the radiotelescope of VLBI complex "Quasar "

NASA Astrophysics Data System (ADS)

Syrovoy, Sergey

At present the radiointerferometry with Very Long Bases (VLBI) is more and more globalized, turning into the world network of observation posts. So the inclusion of the developing Russian system "Quasar" into the world VLBI community has a great importance to us. The important role in the work of radiotelescope as a part of VLBI network belongs to a question of ensuring the optimal interaction of the its sub-systems, which can only be done by means of automation of the whole process of observation. The possibility of participation of RTF-32 in the international VLBI sessions observation is taken into account in the system development. These observations have the stable technology of experiments on the base Mark-IV Field System. In this paper the description, the structured and the functional schemes of the system of automatic collection of parameters and control of receiving complex of radiotelescope RTF-32 are given. This system is to solve the given problem. The most important tasks of the system being developed are the ensuring of distant checking and control of the following systems of the radiotelescope: 1. the receivers system, which consists of the five dual-channel radiometers 21-18 sm, 13 sm, 6 sm, 3.5 sm, 1.35 sm brands; 2. the radiotelescope pointing system; 3. the frequency-time synchronizing system, which consists of the hydrogen standard of frequency, the system of ultrahigh frequency oscillators and the generators of picosecond impulses; 4. the signal transformation system; 5. the signal registration system; 6. the system of measurement of electrical features of atmosphere; 7. the power supply system. The part of the automatic system, ensuring the distant checking and control of the radiotelescope pointing system both in the local mode and in the state of working under control the Field System computer, was put into operation and is functioning at this moment. Now the part of the automatic system ensuring the checking and control of receiving system of radiotelescope is being developed. The functional scheme has been designed. The experimental model of the device of connection of control PC with the terminal has been produced. The algorithms of receiver control in the different modes of observation have been developed. The questions of interaction with the computer Field System have been solved. The radiotelescope RTF-32 is capable of functioning in two modes such as radio-astronomical and radio-interferometrical. The control of the transformation signal system and the registration signal system in these modes is different and is entrusted with the Field System computer. The automation of collection of the meteorological data and parameters of the power supply system of the radiotelescope is last stage of the development of the presented system.

Comparative health systems research among Kaiser Permanente and other integrated delivery systems: a systematic literature review.

PubMed

Maeda, Jared Lane K; Lee, Karen M; Horberg, Michael

2014-01-01

Because of rising health care costs, wide variations in quality, and increased patient complexity, the US health care system is undergoing rapid changes that include payment reform and movement toward integrated delivery systems. Well-established integrated delivery systems, such as Kaiser Permanente (KP), should work to identify the specific system-level factors that result in superior patient outcomes in response to policymakers' concerns. Comparative health systems research can provide insights into which particular aspects of the integrated delivery system result in improved care delivery. To provide a baseline understanding of comparative health systems research related to integrated delivery systems and KP. Systematic literature review. We conducted a literature search on PubMed and the KP Publications Library. Studies that compared KP as a system or organization with other health care systems or across KP facilities internally were included. The literature search identified 1605 articles, of which 65 met the study inclusion criteria and were examined by 3 reviewers. Most comparative health systems studies focused on intra-KP comparisons (n = 42). Fewer studies compared KP with other US (n = 15) or international (n = 12) health care systems. Several themes emerged from the literature as possible factors that may contribute to improved care delivery in integrated delivery systems. Of all studies published by or about KP, only a small proportion of articles (4%) was identified as being comparative health systems research. Additional empirical studies that compare the specific factors of the integrated delivery system model with other systems of care are needed to better understand the "system-level" factors that result in improved and/or diminished care delivery.

Westinghouse Small Modular Reactor balance of plant and supporting systems design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Memmott, M. J.; Stansbury, C.; Taylor, C.

2012-07-01

The Westinghouse Small Modular Reactor (SMR) is an 800 MWt (>225 MWe) integral pressurized water reactor (iPWR), in which all of the components typically associated with the nuclear steam supply system (NSSS) of a nuclear power plant are incorporated within a single reactor pressure vessel. This paper is the second in a series of four papers which describe the design and functionality of the Westinghouse SMR. It focuses, in particular, upon the supporting systems and the balance of plant (BOP) designs of the Westinghouse SMR. Several Westinghouse SMR systems are classified as safety, and are critical to the safe operationmore » of the Westinghouse SMR. These include the protection and monitoring system (PMS), the passive core cooling system (PXS), and the spent fuel cooling system (SFS) including pools, valves, and piping. The Westinghouse SMR safety related systems include the instrumentation and controls (I and C) as well as redundant and physically separated safety trains with batteries, electrical systems, and switch gears. Several other incorporated systems are non-safety related, but provide functions for plant operations including defense-in-depth functions. These include the chemical volume control system (CVS), heating, ventilation and cooling (HVAC) systems, component cooling water system (CCS), normal residual heat removal system (RNS) and service water system (SWS). The integrated performance of the safety-related and non-safety related systems ensures the safe and efficient operation of the Westinghouse SMR through various conditions and transients. The turbine island consists of the turbine, electric generator, feedwater and steam systems, moisture separation systems, and the condensers. The BOP is designed to minimize assembly time, shipping challenges, and on-site testing requirements for all structures, systems, and components. (authors)« less

On the validity of Zeeman's classification for three dimensional competitive differential equations with linearly determined nullclines

NASA Astrophysics Data System (ADS)

Jiang, Jifa; Niu, Lei

2017-12-01

We study three dimensional competitive differential equations with linearly determined nullclines and prove that they always have 33 stable nullcline classes in total. Each class is given in terms of inequalities on the intrinsic growth rates and competitive coefficients and is independent of generating functions. The common characteristics are that every trajectory converges to an equilibrium in classes 1-25, that Hopf bifurcations do not occur within class 32, and that there is always a heteroclinic cycle in class 27. Nontrivial dynamical behaviors, such as the existence and multiplicity of limit cycles, only may occur in classes 26-33, but these nontrivial dynamical behaviors depend on generating functions. We show that Hopf bifurcation can occur within each of classes 26-31 for continuous-time Leslie/Gower system and Ricker system, the same as Lotka-Volterra system; but it only occurs in classes 26 and 27 for continuous-time Atkinson/Allen system and Gompertz system. There is an apparent distinction between Lotka-Volterra system and Leslie/Gower system, Ricker system, Atkinson/Allen system, and Gompertz system with the identical growth rate. Lotka-Volterra system with the identical growth rate has no limit cycle, but admits a center on the carrying simplex in classes 26 and 27. But Leslie/Gower system, Ricker system, Atkinson/Allen system, and Gompertz system with the identical growth rate do possess limit cycles. At last, we provide examples to show that Leslie/Gower system and Ricker system can also admit two limit cycles. This general classification greatly widens applications of Zeeman's method and makes it possible to investigate the existence and multiplicity of limit cycles, centers and stability of heteroclinic cycles for three dimensional competitive systems with linearly determined nullclines, as done in planar systems.

Emergy evaluation of contrasting dairy systems at multiple levels.

PubMed

Vigne, Mathieu; Peyraud, Jean-Louis; Lecomte, Philippe; Corson, Michael S; Wilfart, Aurélie

2013-11-15

Emergy accounting (EmA) was applied to a range of dairy systems, from low-input smallholder systems in South Mali (SM), to intermediate-input systems in two regions of France, Poitou-Charentes (PC) and Bretagne (BR), to high-input systems on Reunion Island (RI). These systems were studied at three different levels: whole-farm (dairy system and cropping system), dairy-system (dairy herd and forage land), and herd (animals only). Dairy farms in SM used the lowest total emergy at all levels and was the highest user of renewable resources. Despite the low quality of resources consumed (crop residues and natural pasture), efficiency of their use was similar to that of industrialised inputs by intensive systems in RI, PC and BR. In addition, among the systems studied, SM dairy farms lay closest to environmental sustainability, contradicting the usual image of high environmental impact of cattle production in developing countries. EmA also revealed characteristics of the three intensive systems. Systems from RI and PC had lower resource transformation efficiency and higher environmental impacts than those from BR, due mainly to feeding strategies that differed due to differing socio-climatic constraints. Application of EmA at multiple levels revealed the importance of a multi-level analysis. While the whole-farm level assesses the overall contribution of the system to its environment, the dairy-system level is suitable for comparison of multi-product systems. In contrast, the herd level focuses on herd management and bypasses debates about definition of system boundaries by excluding land management. Combining all levels highlights the contribution of livestock to the global agricultural system and identifies inefficiencies and influences of system components on the environment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Recognition and categorization considerations for information assurance requirements development and speficication

NASA Astrophysics Data System (ADS)

Stytz, Martin R.; May, Michael; Banks, Sheila B.

2009-04-01

Department of Defense (DoD) Information Technology (IT) systems operate in an environment different from the commercial world, the differences arise from the differences in the types of attacks, the interdependencies between DoD software systems, and the reliance upon commercial software to provide basic capabilities. The challenge that we face is determining how to specify the information assurance requirements for a system without requiring changes to the commercial software and in light of the interdependencies between systems. As a result of the interdependencies and interconnections between systems introduced by the global information grid (GIG), an assessment of the IA requirements for a system must consider three facets of a system's IA capabilities: 1) the IA vulnerabilities of the system, 2) the ability of a system to repel IA attacks, and 3) the ability of a system to insure that any IA attack that penetrates the system is contained within the system and does not spread. Each facet should be assessed independently and the requirements should be derived independently from the assessments. In addition to the desired IA technology capabilities of the system, a complete assessment of the system's overall IA security technology readiness level cannot be accomplished without an assessment of the capabilities required of the system for its capability to recover from and remediate IA vulnerabilities and compromises. To allow us to accomplish these three formidable tasks, we propose a general system architecture designed to separate the system's IA capabilities from its other capability requirements; thereby allowing the IA capabilities to be developed and assessed separately from the other system capabilities. The architecture also enables independent requirements specification, implementation, assessment, measurement, and improvement of a system's IA capabilities without requiring modification of the underlying application software.

Characterization of Dutch dairy farms using sensor systems for cow management.

PubMed

Steeneveld, W; Hogeveen, H

2015-01-01

To improve cow management in large dairy herds, sensors have been developed that can measure physiological, behavioral, and production indicators on individual cows. Recently, the number of dairy farms using sensor systems has increased. It is not known, however, to what extent sensor systems are used on dairy farms, and the reasons why farmers invest or not in sensor systems are unclear. The first objective of this study was to give an overview of the sensor systems currently used in the Netherlands. The second objective was to investigate the reasons for investing or not investing in sensor systems. The third objective was to characterize farms with and without sensor systems. A survey was developed to investigate first, the reasons for investing or not in sensor systems and, then, how the sensor systems are used in daily cow management. The survey was sent to 1,672 Dutch dairy farmers. The final data set consisted of 512 dairy farms (response rate of 30.6%); 202 farms indicated that they had sensor systems and 310 farms indicated that they did not have sensor systems. A wide variety of sensor systems was used on Dutch dairy farms; those for mastitis detection and estrus detection were the most-used sensor systems. The use of sensor systems was different for farms using an automatic milking system (AMS) and a conventional milking system (CMS). Reasons for investing were different for different sensor systems. For sensor systems attached to the AMS, the farmers made no conscious decision to invest: they answered that the sensors were standard in the AMS or were bought for reduced cost with the AMS. The main reasons for investing in estrus detection sensor systems were improving detection rates, gaining insights into the fertility level of the herd, improving profitability of the farm, and reducing labor. Main reasons for not investing in sensor systems were economically related. It was very difficult to characterize farms with and without sensor systems. Farms with CMS and sensor systems had more cows than CMS farms without sensor systems. Furthermore, farms with sensor systems had fewer labor hours per cow compared with farms without sensor systems. Other farm characteristics (age of the farmer, availability of a successor, growth in herd size, milk production per cow, number of cows per hectare, and milk production per hectare) did not differ for farms with and without sensor systems. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Analyzing Effect of System Inertia on Grid Frequency Forecasting Usnig Two Stage Neuro-Fuzzy System

NASA Astrophysics Data System (ADS)

Chourey, Divyansh R.; Gupta, Himanshu; Kumar, Amit; Kumar, Jitesh; Kumar, Anand; Mishra, Anup

2018-04-01

Frequency forecasting is an important aspect of power system operation. The system frequency varies with load-generation imbalance. Frequency variation depends upon various parameters including system inertia. System inertia determines the rate of fall of frequency after the disturbance in the grid. Though, inertia of the system is not considered while forecasting the frequency of power system during planning and operation. This leads to significant errors in forecasting. In this paper, the effect of inertia on frequency forecasting is analysed for a particular grid system. In this paper, a parameter equivalent to system inertia is introduced. This parameter is used to forecast the frequency of a typical power grid for any instant of time. The system gives appreciable result with reduced error.

OFMTutor: An operator function model intelligent tutoring system

NASA Technical Reports Server (NTRS)

Jones, Patricia M.

1989-01-01

The design, implementation, and evaluation of an Operator Function Model intelligent tutoring system (OFMTutor) is presented. OFMTutor is intended to provide intelligent tutoring in the context of complex dynamic systems for which an operator function model (OFM) can be constructed. The human operator's role in such complex, dynamic, and highly automated systems is that of a supervisory controller whose primary responsibilities are routine monitoring and fine-tuning of system parameters and occasional compensation for system abnormalities. The automated systems must support the human operator. One potentially useful form of support is the use of intelligent tutoring systems to teach the operator about the system and how to function within that system. Previous research on intelligent tutoring systems (ITS) is considered. The proposed design for OFMTutor is presented, and an experimental evaluation is described.

Autonomous Operations System: Development and Application

NASA Technical Reports Server (NTRS)

Toro Medina, Jaime A.; Wilkins, Kim N.; Walker, Mark; Stahl, Gerald M.

2016-01-01

Autonomous control systems provides the ability of self-governance beyond the conventional control system. As the complexity of mechanical and electrical systems increases, there develops a natural drive for developing robust control systems to manage complicated operations. By closing the bridge between conventional automated systems to knowledge based self-awareness systems, nominal control of operations can evolve into relying on safe critical mitigation processes to support any off-nominal behavior. Current research and development efforts lead by the Autonomous Propellant Loading (APL) group at NASA Kennedy Space Center aims to improve cryogenic propellant transfer operations by developing an automated control and health monitoring system. As an integrated systems, the center aims to produce an Autonomous Operations System (AOS) capable of integrating health management operations with automated control to produce a fully autonomous system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myers, D.W.; Baker, J.; Benzel, D.M.

This paper describes an unattended ground sensor system that has been developed for the immigration and Naturalization Service (INS). The system, known as INSENS, was developed at the Lawrence Livermore National Laboratory for use by the United States Border Patrol. This system assists in the detection of illegal entry of aliens and contraband (illegal drugs, etc.) into the United States along its land borders. Key to the system is its flexible modular design which allows future software and hardware enhancements to the system without altering the fundamental architecture of the system. Elements of the system include a sensor system capablemore » of processing signals from multiple directional probes, a repeater system, and a handheld monitor system. Seismic, passive infrared (PIR), and magnetic probes are currently supported. The design of the INSENS system elements and their performance are described.« less

Symmetry of interactions rules in incompletely connected random replicator ecosystems.

PubMed

Kärenlampi, Petri P

2014-06-01

The evolution of an incompletely connected system of species with speciation and extinction is investigated in terms of random replicators. It is found that evolving random replicator systems with speciation do become large and complex, depending on speciation parameters. Antisymmetric interactions result in large systems, whereas systems with symmetric interactions remain small. A co-dominating feature is within-species interaction pressure: large within-species interaction increases species diversity. Average fitness evolves in all systems, however symmetry and connectivity evolve in small systems only. Newcomers get extinct almost immediately in symmetric systems. The distribution in species lifetimes is determined for antisymmetric systems. The replicator systems investigated do not show any sign of self-organized criticality. The generalized Lotka-Volterra system is shown to be a tedious way of implementing the replicator system.

Thrust distribution for attitude control in a variable thrust propulsion system with four ACS nozzles

NASA Astrophysics Data System (ADS)

Lim, Yeerang; Lee, Wonsuk; Bang, Hyochoong; Lee, Hosung

2017-04-01

A thrust distribution approach is proposed in this paper for a variable thrust solid propulsion system with an attitude control system (ACS) that uses a reduced number of nozzles for a three-axis attitude maneuver. Although a conventional variable thrust solid propulsion system needs six ACS nozzles, this paper proposes a thrust system with four ACS nozzles to reduce the complexity and mass of the system. The performance of the new system was analyzed with numerical simulations, and the results show that the performance of the system with four ACS nozzles was similar to the original system while the mass of the whole system was simultaneously reduced. Moreover, a feasibility analysis was performed to determine whether a thrust system with three ACS nozzles is possible.

Bacteria-Triggered Systemic Immunity in Barley Is Associated with WRKY and ETHYLENE RESPONSIVE FACTORs But Not with Salicylic Acid1[C][W

PubMed Central

Dey, Sanjukta; Wenig, Marion; Langen, Gregor; Sharma, Sapna; Kugler, Karl G.; Knappe, Claudia; Hause, Bettina; Bichlmeier, Marlies; Babaeizad, Valiollah; Imani, Jafargholi; Janzik, Ingar; Stempfl, Thomas; Hückelhoven, Ralph; Kogel, Karl-Heinz; Mayer, Klaus F.X.

2014-01-01

Leaf-to-leaf systemic immune signaling known as systemic acquired resistance is poorly understood in monocotyledonous plants. Here, we characterize systemic immunity in barley (Hordeum vulgare) triggered after primary leaf infection with either Pseudomonas syringae pathovar japonica (Psj) or Xanthomonas translucens pathovar cerealis (Xtc). Both pathogens induced resistance in systemic, uninfected leaves against a subsequent challenge infection with Xtc. In contrast to systemic acquired resistance in Arabidopsis (Arabidopsis thaliana), systemic immunity in barley was not associated with NONEXPRESSOR OF PATHOGENESIS-RELATED GENES1 or the local or systemic accumulation of salicylic acid. Instead, we documented a moderate local but not systemic induction of abscisic acid after infection of leaves with Psj. In contrast to salicylic acid or its functional analog benzothiadiazole, local applications of the jasmonic acid methyl ester or abscisic acid triggered systemic immunity to Xtc. RNA sequencing analysis of local and systemic transcript accumulation revealed unique gene expression changes in response to both Psj and Xtc and a clear separation of local from systemic responses. The systemic response appeared relatively modest, and quantitative reverse transcription-polymerase chain reaction associated systemic immunity with the local and systemic induction of two WRKY and two ETHYLENE RESPONSIVE FACTOR (ERF)-like transcription factors. Systemic immunity against Xtc was further associated with transcriptional changes after a secondary/systemic Xtc challenge infection; these changes were dependent on the primary treatment. Taken together, bacteria-induced systemic immunity in barley may be mediated in part by WRKY and ERF-like transcription factors, possibly facilitating transcriptional reprogramming to potentiate immunity. PMID:25332505

Modeling Sustainability: Population, Inequality, Consumption, and Bidirectional Coupling of the Earth and Human Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motesharrei, Safa; Rivas, Jorge; Kalnay, Eugenia

Over the last two centuries, the impact of the Human System has grown dramatically, becoming strongly dominant within the Earth System in many different ways. Consumption, inequality, and population have increased extremely fast, especially since about 1950, threatening to overwhelm the many critical functions and ecosystems of the Earth System. Changes in the Earth System, in turn, have important feedback effects on the Human System, with costly and potentially serious consequences. However, current models do not incorporate these critical feedbacks. Here, we argue that in order to understand the dynamics of either system, Earth System Models must be coupled withmore » Human System Models through bidirectional couplings representing the positive, negative, and delayed feedbacks that exist in the real systems. In particular, key Human System variables, such as demographics, inequality, economic growth, and migration, are not coupled with the Earth System but are instead driven by exogenous estimates, such as United Nations population projections.This makes current models likely to miss important feedbacks in the real Earth–Human system, especially those that may result in unexpected or counterintuitive outcomes, and thus requiring different policy interventions from current models. Lastly, the importance and imminence of sustainability challenges, the dominant role of the Human System in the Earth System, and the essential roles the Earth System plays for the Human System, all call for collaboration of natural scientists, social scientists, and engineers in multidisciplinary research and modeling to develop coupled Earth–Human system models for devising effective science-based policies and measures to benefit current and future generations.« less

Modeling Sustainability: Population, Inequality, Consumption, and Bidirectional Coupling of the Earth and Human Systems

NASA Technical Reports Server (NTRS)

Motesharrei, Safa; Rivas, Jorge; Kalnay, Eugenia; Asrar, Ghassem R.; Busalacchi, Antonio J.; Cahalan, Robert F.; Cane, Mark A.; Colwell, Rita R.; Feng, Kuishuang; Franklin, Rachel S.;

Modeling Sustainability: Population, Inequality, Consumption, and Bidirectional Coupling of the Earth and Human Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motesharrei, Safa; Rivas, Jorge; Kalnay, Eugenia

Over the last two centuries, the impact of the Human System has grown dramatically, becoming strongly dominant within the Earth System in many different ways. Consumption, inequality, and population have increased extremely fast, especially since about 1950, threatening to overwhelm the many critical functions and ecosystems of the Earth System. Changes in the Earth System, in turn, have important feedback effects on the Human System, with costly and potentially serious consequences. However, current models do not incorporate these critical feedbacks. We argue that in order to understand the dynamics of either system, Earth System Models must be coupled with Humanmore » System Models through bidirectional couplings representing the positive, negative, and delayed feedbacks that exist in the real systems. In particular, key Human System variables, such as demographics, inequality, economic growth, and migration, are not coupled with the Earth System but are instead driven by exogenous estimates, such as United Nations population projections. This makes current models likely to miss important feedbacks in the real Earth–Human system, especially those that may result in unexpected or counterintuitive outcomes, and thus requiring different policy interventions from current models. The importance and imminence of sustainability challenges, the dominant role of the Human System in the Earth System, and the essential roles the Earth System plays for the Human System, all call for collaboration of natural scientists, social scientists, and engineers in multidisciplinary research and modeling to develop coupled Earth–Human system models for devising effective science-based policies and measures to benefit current and future generations.« less

Modeling Sustainability: Population, Inequality, Consumption, and Bidirectional Coupling of the Earth and Human Systems

DOE PAGES

Motesharrei, Safa; Rivas, Jorge; Kalnay, Eugenia; ...

2016-12-11

Over the last two centuries, the impact of the Human System has grown dramatically, becoming strongly dominant within the Earth System in many different ways. Consumption, inequality, and population have increased extremely fast, especially since about 1950, threatening to overwhelm the many critical functions and ecosystems of the Earth System. Changes in the Earth System, in turn, have important feedback effects on the Human System, with costly and potentially serious consequences. However, current models do not incorporate these critical feedbacks. Here, we argue that in order to understand the dynamics of either system, Earth System Models must be coupled withmore » Human System Models through bidirectional couplings representing the positive, negative, and delayed feedbacks that exist in the real systems. In particular, key Human System variables, such as demographics, inequality, economic growth, and migration, are not coupled with the Earth System but are instead driven by exogenous estimates, such as United Nations population projections.This makes current models likely to miss important feedbacks in the real Earth–Human system, especially those that may result in unexpected or counterintuitive outcomes, and thus requiring different policy interventions from current models. Lastly, the importance and imminence of sustainability challenges, the dominant role of the Human System in the Earth System, and the essential roles the Earth System plays for the Human System, all call for collaboration of natural scientists, social scientists, and engineers in multidisciplinary research and modeling to develop coupled Earth–Human system models for devising effective science-based policies and measures to benefit current and future generations.« less

A Performance Comparison of Tree and Ring Topologies in Distributed System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Min

A distributed system is a collection of computers that are connected via a communication network. Distributed systems have become commonplace due to the wide availability of low-cost, high performance computers and network devices. However, the management infrastructure often does not scale well when distributed systems get very large. Some of the considerations in building a distributed system are the choice of the network topology and the method used to construct the distributed system so as to optimize the scalability and reliability of the system, lower the cost of linking nodes together and minimize the message delay in transmission, and simplifymore » system resource management. We have developed a new distributed management system that is able to handle the dynamic increase of system size, detect and recover the unexpected failure of system services, and manage system resources. The topologies used in the system are the tree-structured network and the ring-structured network. This thesis presents the research background, system components, design, implementation, experiment results and the conclusions of our work. The thesis is organized as follows: the research background is presented in chapter 1. Chapter 2 describes the system components, including the different node types and different connection types used in the system. In chapter 3, we describe the message types and message formats in the system. We discuss the system design and implementation in chapter 4. In chapter 5, we present the test environment and results, Finally, we conclude with a summary and describe our future work in chapter 6.« less

Design and performance of daily quality assurance system for carbon ion therapy at NIRS

NASA Astrophysics Data System (ADS)

Saotome, N.; Furukawa, T.; Hara, Y.; Mizushima, K.; Tansho, R.; Saraya, Y.; Shirai, T.; Noda, K.

2017-09-01

At National Institute of Radiological Sciences (NIRS), we have been commissioning a rotating-gantry system for carbon-ion radiotherapy. This rotating gantry can transport heavy ions at 430 MeV/u to an isocenter with irradiation angles of ±180° that can rotate around the patient so that the tumor can be irradiated from any direction. A three-dimensional pencil-beam scanning irradiation system equipped with the rotating gantry enables the optimal use of physical characteristics of carbon ions to provide accurate treatment. To ensure the treatment quality using such a complex system, the calibration of the primary dose monitor, output check, range check, dose rate check, machine safety check, and some mechanical tests should be performed efficiently. For this purpose, we have developed a measurement system dedicated for quality assurance (QA) of this gantry system: the Daily QA system. The system consists of an ionization chamber system and a scintillator system. The ionization chamber system is used for the calibration of the primary dose monitor, output check, and dose rate check, and the scintillator system is used for the range check, isocenter, and gantry angle. The performance of the Daily QA system was verified by a beam test. The stability of the output was within 0.5%, and the range was within 0.5 mm. The coincidence of the coordinates between the patient-positioning system and the irradiation system was verified using the Daily QA system. Our present findings verified that the new Daily QA system for a rotating gantry is capable of verifying the irradiation system with sufficient accuracy.

Multispectral scanner system for ERTS: Four-band scanner system. Volume 1: System description and performance

NASA Technical Reports Server (NTRS)

Norwood, V. T.; Fermelia, L. R.; Tadler, G. A.

1972-01-01

The four-band Multispectral Scanner System (MSS) is discussed. Included is a description of the MSS with major emphasis on the flight subsystem (scanner and multiplexer), the theory for the MSS calibration system processing techniques, system calibration data, and a summary of the performance of the two four-band MSS systems.

Apollo Command and Service Module Propulsion Systems Overview

NASA Technical Reports Server (NTRS)

Interbartolo, Michael A.

2009-01-01

An overview of the Apollo Command and Service Module (CSM) propulsion systems is provided. The systems for CSM propulsion and control are defined, the times during the mission when each system is used are listed, and, the basic components and operation of the service propulsion system, SM reaction control system and CM reaction control system are described.

RICIS Symposium 1992: Mission and Safety Critical Systems Research and Applications

NASA Technical Reports Server (NTRS)

1992-01-01

This conference deals with computer systems which control systems whose failure to operate correctly could produce the loss of life and or property, mission and safety critical systems. Topics covered are: the work of standards groups, computer systems design and architecture, software reliability, process control systems, knowledge based expert systems, and computer and telecommunication protocols.

77 FR 49011 - Privacy Act of 1974; New System of Records, Office of General Counsel E-Discovery Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-15

... System of Records, Office of General Counsel E-Discovery Management System--Change in Final Effective... the OGC E-Discovery Management System until after the opportunity for further comment is provided to... intent to establish a new system of records for OGC's E-Discovery Management System (EDMS), a system...

77 FR 68140 - Privacy Act of 1974; New System of Records, Office of General Counsel E-Discovery Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-15

... System of Records, Office of General Counsel E-Discovery Management System: Republication of System... Counsel (OGC) E- Discovery Management System (EDMS). EDMS was first announced and described in a July 17... for OGC's E-Discovery Management System (OGC-EDMS), a system expected to significantly improve the...

What Is Energy Systems Integration? | Energy Systems Integration Facility |

Science.gov Websites

NREL What Is Energy Systems Integration? What Is Energy Systems Integration? Energy systems integration (ESI) is an approach to solving big energy challenges that explores ways for energy systems to Research Community NREL is a founding member of the International Institute for Energy Systems Integration

48 CFR 245.105 - Contractors' property management system compliance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... management system compliance. 245.105 Section 245.105 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT GOVERNMENT PROPERTY General 245.105 Contractors' property management system compliance. (a) Definitions— (1) Acceptable property management system...

Classification systems for causes of stillbirth and neonatal death, 2009-2014: an assessment of alignment with characteristics for an effective global system.

PubMed

Leisher, Susannah Hopkins; Teoh, Zheyi; Reinebrant, Hanna; Allanson, Emma; Blencowe, Hannah; Erwich, Jan Jaap; Frøen, J Frederik; Gardosi, Jason; Gordijn, Sanne; Gülmezoglu, A Metin; Heazell, Alexander E P; Korteweg, Fleurisca; Lawn, Joy; McClure, Elizabeth M; Pattinson, Robert; Smith, Gordon C S; Tunçalp, Ӧzge; Wojcieszek, Aleena M; Flenady, Vicki

2016-09-15

To reduce the burden of 5.3 million stillbirths and neonatal deaths annually, an understanding of causes of deaths is critical. A systematic review identified 81 systems for classification of causes of stillbirth (SB) and neonatal death (NND) between 2009 and 2014. The large number of systems hampers efforts to understand and prevent these deaths. This study aimed to assess the alignment of current classification systems with expert-identified characteristics for a globally effective classification system. Eighty-one classification systems were assessed for alignment with 17 characteristics previously identified through expert consensus as necessary for an effective global system. Data were extracted independently by two authors. Systems were assessed against each characteristic and weighted and unweighted scores assigned to each. Subgroup analyses were undertaken by system use, setting, type of death included and type of characteristic. None of the 81 systems were aligned with more than 9 of the 17 characteristics; most (82 %) were aligned with four or fewer. On average, systems were aligned with 19 % of characteristics. The most aligned system (Frøen 2009-Codac) still had an unweighted score of only 9/17. Alignment with individual characteristics ranged from 0 to 49 %. Alignment was somewhat higher for widely used as compared to less used systems (22 % v 17 %), systems used only in high income countries as compared to only in low and middle income countries (20 % vs 16 %), and systems including both SB and NND (23 %) as compared to NND-only (15 %) and SB-only systems (13 %). Alignment was higher with characteristics assessing structure (23 %) than function (15 %). There is an unmet need for a system exhibiting all the characteristics of a globally effective system as defined by experts in the use of systems, as none of the 81 contemporary classification systems assessed was highly aligned with these characteristics. A particular concern in terms of global effectiveness is the lack of alignment with "ease of use" among all systems, including even the most-aligned. A system which meets the needs of users would have the potential to become the first truly globally effective classification system.

Properties of the single Jovian planet population and the pursuit of Solar system analogues

NASA Astrophysics Data System (ADS)

Agnew, Matthew T.; Maddison, Sarah T.; Horner, Jonathan

2018-07-01

While the number of exoplanets discovered continues to increase at a rapid rate, we are still to discover any system that truly resembles the Solar system. Existing and near future surveys will likely continue this trend of rapid discovery. To see if these systems are Solar system analogues, we will need to efficiently allocate resources to carry out intensive follow-up observations. We seek to uncover the properties and trends across systems that indicate how much of the habitable zone is stable in each system to provide focus for planet hunters. We study the dynamics of all known single Jovian planetary systems to assess the dynamical stability of the habitable zone around their host stars. We perform a suite of simulations of all systems where the Jovian planet will interact gravitationally with the habitable zone, and broadly classify these systems. Besides the system's mass ratio (Mpl/Mstar), the Jovian planet's semimajor axis (apl), and eccentricity (epl), we find that there are no underlying system properties which are observable that indicate the potential for planets to survive within the system's habitable zone. We use Mpl/Mstar, apl, and epl to generate a parameter space over which the unstable systems cluster, thus allowing us to predict which systems to exclude from future observational or numerical searches for habitable exoplanets. We also provide a candidate list of 20 systems that have completely stable habitable zones and Jovian planets orbiting beyond the habitable zone as potential first-order Solar system analogues.

A novel simulation theory and model system for multi-field coupling pipe-flow system

NASA Astrophysics Data System (ADS)

Chen, Yang; Jiang, Fan; Cai, Guobiao; Xu, Xu

2017-09-01

Due to the lack of a theoretical basis for multi-field coupling in many system-level models, a novel set of system-level basic equations for flow/heat transfer/combustion coupling is put forward. Then a finite volume model of quasi-1D transient flow field for multi-species compressible variable-cross-section pipe flow is established by discretising the basic equations on spatially staggered grids. Combining with the 2D axisymmetric model for pipe-wall temperature field and specific chemical reaction mechanisms, a finite volume model system is established; a set of specific calculation methods suitable for multi-field coupling system-level research is structured for various parameters in this model; specific modularisation simulation models can be further derived in accordance with specific structures of various typical components in a liquid propulsion system. This novel system can also be used to derive two sub-systems: a flow/heat transfer two-field coupling pipe-flow model system without chemical reaction and species diffusion; and a chemical equilibrium thermodynamic calculation-based multi-field coupling system. The applicability and accuracy of two sub-systems have been verified through a series of dynamic modelling and simulations in earlier studies. The validity of this system is verified in an air-hydrogen combustion sample system. The basic equations and the model system provide a unified universal theory and numerical system for modelling and simulation and even virtual testing of various pipeline systems.

Properties of the single Jovian planet population and the pursuit of Solar system analogues

NASA Astrophysics Data System (ADS)

Agnew, Matthew T.; Maddison, Sarah T.; Horner, Jonathan

2018-04-01

While the number of exoplanets discovered continues to increase at a rapid rate, we are still to discover any system that truly resembles the Solar system. Existing and near future surveys will likely continue this trend of rapid discovery. To see if these systems are Solar system analogues, we will need to efficiently allocate resources to carry out intensive follow-up observations. We seek to uncover the properties and trends across systems that indicate how much of the habitable zone is stable in each system to provide focus for planet hunters. We study the dynamics of all known single Jovian planetary systems, to assess the dynamical stability of the habitable zone around their host stars. We perform a suite of simulations of all systems where the Jovian planet will interact gravitationally with the habitable zone, and broadly classify these systems. Besides the system's mass ratio (Mpl/Mstar), and the Jovian planet's semi-major axis (apl) and eccentricity (epl), we find that there are no underlying system properties which are observable that indicate the potential for planets to survive within the system's habitable zone. We use Mpl/Mstar, apl and epl to generate a parameter space over which the unstable systems cluster, thus allowing us to predict which systems to exclude from future observational or numerical searches for habitable exoplanets. We also provide a candidate list of 20 systems that have completely stable habitable zones and Jovian planets orbiting beyond the habitable zone as potential first order Solar system analogues.

Fuzzy Integration of Support Vector Regression Models for Anticipatory Control of Complex Energy Systems

DOE PAGES

Alamaniotis, Miltiadis; Agarwal, Vivek

2014-04-01

Anticipatory control systems are a class of systems whose decisions are based on predictions for the future state of the system under monitoring. Anticipation denotes intelligence and is an inherent property of humans that make decisions by projecting in future. Likewise, artificially intelligent systems equipped with predictive functions may be utilized for anticipating future states of complex systems, and therefore facilitate automated control decisions. Anticipatory control of complex energy systems is paramount to their normal and safe operation. In this paper a new intelligent methodology integrating fuzzy inference with support vector regression is introduced. Our proposed methodology implements an anticipatorymore » system aiming at controlling energy systems in a robust way. Initially a set of support vector regressors is adopted for making predictions over critical system parameters. Furthermore, the predicted values are fed into a two stage fuzzy inference system that makes decisions regarding the state of the energy system. The inference system integrates the individual predictions into a single one at its first stage, and outputs a decision together with a certainty factor computed at its second stage. The certainty factor is an index of the significance of the decision. The proposed anticipatory control system is tested on a real world set of data obtained from a complex energy system, describing the degradation of a turbine. Results exhibit the robustness of the proposed system in controlling complex energy systems.« less

Assessment of the integration capability of system architectures from a complex and distributed software systems perspective

NASA Astrophysics Data System (ADS)

Leuchter, S.; Reinert, F.; Müller, W.

2014-06-01

Procurement and design of system architectures capable of network centric operations demand for an assessment scheme in order to compare different alternative realizations. In this contribution an assessment method for system architectures targeted at the C4ISR domain is presented. The method addresses the integration capability of software systems from a complex and distributed software system perspective focusing communication, interfaces and software. The aim is to evaluate the capability to integrate a system or its functions within a system-of-systems network. This method uses approaches from software architecture quality assessment and applies them on the system architecture level. It features a specific goal tree of several dimensions that are relevant for enterprise integration. These dimensions have to be weighed against each other and totalized using methods from the normative decision theory in order to reflect the intention of the particular enterprise integration effort. The indicators and measurements for many of the considered quality features rely on a model based view on systems, networks, and the enterprise. That means it is applicable to System-of-System specifications based on enterprise architectural frameworks relying on defined meta-models or domain ontologies for defining views and viewpoints. In the defense context we use the NATO Architecture Framework (NAF) to ground respective system models. The proposed assessment method allows evaluating and comparing competing system designs regarding their future integration potential. It is a contribution to the system-of-systems engineering methodology.

Structural analysis and design for the development of floating photovoltaic energy generation system

NASA Astrophysics Data System (ADS)

Yoon, S. J.; Joo, H. J.; Kim, S. H.

2018-06-01

In this paper, we discussed the structural analysis and design for the development of floating photovoltaic energy generation system. Series of research conducted to develop the system from the analysis and design of the structural system to the installation of the system discussed. In the structural system supporting solar panels PFRP materials and SMC FRP materials used. A unit module structure is fabricated and then the unit module structures are connected each other to assemble whole PV energy generation complex. This system connected directly to the power grid system. In addition, extensive monitoring for the efficiency of electricity generation and the soundness of the structural system is in progress for the further system enhancement.

Design of Smart Home Systems Prototype Using MyRIO

NASA Astrophysics Data System (ADS)

Ratna Wati, Dwi Ann; Abadianto, Dika

2017-06-01

This paper presents the design of smart home systems prototype. It applies. MyRIO 1900 embedded device as the main controller of the smart home systems. The systems include wireless monitoring systems and email based notifications as well as data logging. The prototype systems use simulated sensor such as temperature sensor, push button as proximity sensor, and keypad while its simulated actuators are buzzer as alarm system, LED as light and LCD. Based on the test and analysis, the smart home systems prototype as well as the wireless monitoring systems have real time responses when input signals are available. Tbe performance of MyRIO controller is excellent and it results in a stable system.

Composite Socio-Technical Systems: A Method for Social Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yingchen; He, Fulin; Hao, Jun

In order to model and study the interactions between social on technical systems, a systemic method, namely the composite socio-technical systems (CSTS), is proposed to incorporate social systems, technical systems and the interaction mechanism between them. A case study on University of Denver (DU) campus grid is presented in paper to demonstrate the application of the proposed method. In the case study, the social system, technical system, and the interaction mechanism are defined and modelled within the framework of CSTS. Distributed and centralized control and management schemes are investigated, respectively, and numerical results verifies the feasibility and performance of themore » proposed composite system method.« less

System reliability approaches for advanced propulsion system structures

NASA Technical Reports Server (NTRS)

Cruse, T. A.; Mahadevan, S.

1991-01-01

This paper identifies significant issues that pertain to the estimation and use of system reliability in the design of advanced propulsion system structures. Linkages between the reliabilities of individual components and their effect on system design issues such as performance, cost, availability, and certification are examined. The need for system reliability computation to address the continuum nature of propulsion system structures and synergistic progressive damage modes has been highlighted. Available system reliability models are observed to apply only to discrete systems. Therefore a sequential structural reanalysis procedure is formulated to rigorously compute the conditional dependencies between various failure modes. The method is developed in a manner that supports both top-down and bottom-up analyses in system reliability.

Study of guidance techniques for aerial application of agricultural compounds

NASA Technical Reports Server (NTRS)

Caldwell, J. D.; Dimmock, P. B. A.; Watkins, R. H.

1980-01-01

Candidate systems were identified for evaluation of suitability in meeting specified accuracy requirements for a swath guidance system in an agriculture aircraft. Further examination reduced the list of potential candidates to a single category, i.e., transponder type systems, for detailed evaluation. Within this category three systems were found which met the basic accuracy requirements of the work statement. The Flying Flagman, the Electronic Flagging and the Raydist Director System. In addition to evaluating the systems against the specified requirements, each system was compared with the other two systems on a relative basis. The conclusions supported by the analyses show the Flying Flagman system to be the most suitable system currently available to meet the requirements.

Engineering monitoring expert system's developer

NASA Technical Reports Server (NTRS)

Lo, Ching F.

1991-01-01

This research project is designed to apply artificial intelligence technology including expert systems, dynamic interface of neural networks, and hypertext to construct an expert system developer. The developer environment is specifically suited to building expert systems which monitor the performance of ground support equipment for propulsion systems and testing facilities. The expert system developer, through the use of a graphics interface and a rule network, will be transparent to the user during rule constructing and data scanning of the knowledge base. The project will result in a software system that allows its user to build specific monitoring type expert systems which monitor various equipments used for propulsion systems or ground testing facilities and accrues system performance information in a dynamic knowledge base.

Ecosystem and immune systems: Hierarchial response provides resilience against invasions

USGS Publications Warehouse

Allen, Craig R.

2001-01-01

Janssen (2001) provides the stimulus for thoughtful comparison and consideration of the ranges of responses exhibited by immune systems and ecological systems in the face of perturbations such as biological invasions. It may indeed be informative to consider the similarities of the responses to invasions exhibited by immune systems and ecological systems. Clearly, both types of systems share a general organizational structure with all other complex hierarchical systems. Their organization provides these systems with resilience. However, when describing the response of ecological-economic systems to invasions, Janssen emphasizes the human-economic response. I would like to expand on his comparison by focusing on how resilience is maintained in complex systems under the threat of invasion.

A large scale software system for simulation and design optimization of mechanical systems

NASA Technical Reports Server (NTRS)

Dopker, Bernhard; Haug, Edward J.

1989-01-01

The concept of an advanced integrated, networked simulation and design system is outlined. Such an advanced system can be developed utilizing existing codes without compromising the integrity and functionality of the system. An example has been used to demonstrate the applicability of the concept of the integrated system outlined here. The development of an integrated system can be done incrementally. Initial capabilities can be developed and implemented without having a detailed design of the global system. Only a conceptual global system must exist. For a fully integrated, user friendly design system, further research is needed in the areas of engineering data bases, distributed data bases, and advanced user interface design.

The concept of self-organizing systems. Why bother?

NASA Astrophysics Data System (ADS)

Elverfeldt, Kirsten v.; Embleton-Hamann, Christine; Slaymaker, Olav

2016-04-01

Complexity theory and the concept of self-organizing systems provide a rather challenging conceptual framework for explaining earth systems change. Self-organization - understood as the aggregate processes internal to an environmental system that lead to a distinctive spatial or temporal organization - reduces the possibility of implicating a specific process as being causal, and it poses some restrictions on the idea that external drivers cause a system to change. The concept of self-organizing systems suggests that many phenomena result from an orchestration of different mechanisms, so that no causal role can be assigned to an individual factor or process. The idea that system change can be due to system-internal processes of self-organization thus proves a huge challenge to earth system research, especially in the context of global environmental change. In order to understand the concept's implications for the Earth Sciences, we need to know the characteristics of self-organizing systems and how to discern self-organizing systems. Within the talk, we aim firstly at characterizing self-organizing systems, and secondly at highlighting the advantages and difficulties of the concept within earth system sciences. The presentation concludes that: - The concept of self-organizing systems proves especially fruitful for small-scale earth surface systems. Beach cusps and patterned ground are only two of several other prime examples of self-organizing earth surface systems. They display characteristics of self-organization like (i) system-wide order from local interactions, (ii) symmetry breaking, (iii) distributed control, (iv) robustness and resilience, (v) nonlinearity and feedbacks, (vi) organizational closure, (vii) adaptation, and (viii) variation and selection. - It is comparatively easy to discern self-organization in small-scale systems, but to adapt the concept to larger scale systems relevant to global environmental change research is more difficult: Self-organizing systems seem to form nested hierarchies, and on different hierarchical levels self-organizing and externally driven subsystems might occur simultaneously. - Traditional geomorphological concepts such as sensitivity to change, and intrinsic or extrinsic thresholds are compatible with the concept of self-organizing system, and these concepts are even enriched in their explanatory power when viewed in the larger framework of self-organization. The conceptual step to acknowledge self-organizing system change within earth system sciences thus can be regarded as relatively small. The concept of self-organization suggests a change of focus for earth system change research: a shift from input-output relations toward the inner organization of systems, since external controls rather limit the degrees of freedom of a system instead of triggering changes. Many systems might in fact be rather autonomous, and the specific and observable external trigger might be less important than the intrinsic system state. Hence, neither gradual nor catastrophic system changes necessarily need an external driver. The concept of self-organization provides important caveats to generally attributing environmental change to external drivers, and it encourages a frank admission of ignorance in the face of complexity.

Design and development of an IBM/VM menu system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cazzola, D.J.

1992-10-01

This report describes a full screen menu system developed using IBM's Interactive System Productivity Facility (ISPF) and the REXX programming language. The software was developed for the 2800 IBM/VM Electrical Computer Aided Design (ECAD) system. The system was developed to deliver electronic drawing definitions to a corporate drawing release system. Although this report documents the status of the menu system when it was retired, the methodologies used and the requirements defined are very applicable to replacement systems.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E; Svoboda, John M; West, Phillip B; Heath, Gail L; Scott, Clark L

2015-01-27

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Linear Actuator System for the NASA Docking System

NASA Technical Reports Server (NTRS)

Dick, Brandon N.; Oesch, Christopher; Rupp, Timothy W.

2017-01-01

The Linear Actuator System (LAS) is a major sub-system within the NASA Docking System (NDS). The NDS Block 1 will be used on the Boeing Crew Space Transportation (CST-100) system to achieve docking with the International Space Station. Critical functions in the Soft Capture aspect of docking are performed by the LAS. This paper describes the general function of the LAS, the system's key requirements and technical challenges, and the development and qualification approach for the system.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E [Idaho Falls, ID; Svoboda, John M [Idaho Falls, ID; West, Phillip B [Idaho Falls, ID; Heath, Gail L [Iona, ID; Scott, Clark L [Idaho Falls, ID

2010-08-31

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Cooling of superconducting devices by liquid storage and refrigeration unit

DOEpatents

Laskaris, Evangelos Trifon; Urbahn, John Arthur; Steinbach, Albert Eugene

2013-08-20

A system is disclosed for cooling superconducting devices. The system includes a cryogen cooling system configured to be coupled to the superconducting device and to supply cryogen to the device. The system also includes a cryogen storage system configured to supply cryogen to the device. The system further includes flow control valving configured to selectively isolate the cryogen cooling system from the device, thereby directing a flow of cryogen to the device from the cryogen storage system.

The Dilemma of Department of Defense Business System Modernization Efforts: Why Intended Outcomes Have Not Been Fully Met and What Needs to Change

DTIC Science & Technology

2016-06-01

between contract writing systems and the associated accounting and logistics systems. Employing this modular plug and play approach simplifies system...Automated Contract Preparation System (ACPS), Integrated Technical Item Management (ITIMP), and EProcurement are the contract writing systems that...research was on the DOD contract writing systems (CWS). This JAP seeks to report on the progress of DOD business system modernization efforts and

Digital communications: Microwave applications

NASA Astrophysics Data System (ADS)

Feher, K.

Transmission concepts and techniques of digital systems are presented; and practical state-of-the-art implementation of digital communications systems by line-of-sight microwaves is described. Particular consideration is given to statistical methods in digital transmission systems analysis, digital modulation methods, microwave amplifiers, system gain, m-ary and QAM microwave systems, correlative techniques and applications to digital radio systems, hybrid systems, digital microwave systems design, diversity and protection switching techniques, measurement techniques, and research and development trends and unsolved problems.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E; Svoboda, John M.; West, Phillip B.; Heath, Gail L.; Scott, Clark L.

2016-07-19

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Application of propagation predictions to Earth/space telecommunications system design

NASA Technical Reports Server (NTRS)

1981-01-01

The corresponding between a given propagation phenomenon and system performance is considered. Propagation data are related to system performance parameters, allowing the systems engineer to perform the analyses determining how well requirements are met by a given system design, and enabling the systems engineer to modify that design if necessary. The various ways of specifying performance criteria for different kinds of systems are discussed, and a general procedure for system design is presented and demonstrated.

State Machine Modeling of the Space Launch System Solid Rocket Boosters

NASA Technical Reports Server (NTRS)

Harris, Joshua A.; Patterson-Hine, Ann

2013-01-01

The Space Launch System is a Shuttle-derived heavy-lift vehicle currently in development to serve as NASA's premiere launch vehicle for space exploration. The Space Launch System is a multistage rocket with two Solid Rocket Boosters and multiple payloads, including the Multi-Purpose Crew Vehicle. Planned Space Launch System destinations include near-Earth asteroids, the Moon, Mars, and Lagrange points. The Space Launch System is a complex system with many subsystems, requiring considerable systems engineering and integration. To this end, state machine analysis offers a method to support engineering and operational e orts, identify and avert undesirable or potentially hazardous system states, and evaluate system requirements. Finite State Machines model a system as a finite number of states, with transitions between states controlled by state-based and event-based logic. State machines are a useful tool for understanding complex system behaviors and evaluating "what-if" scenarios. This work contributes to a state machine model of the Space Launch System developed at NASA Ames Research Center. The Space Launch System Solid Rocket Booster avionics and ignition subsystems are modeled using MATLAB/Stateflow software. This model is integrated into a larger model of Space Launch System avionics used for verification and validation of Space Launch System operating procedures and design requirements. This includes testing both nominal and o -nominal system states and command sequences.

Systems Thinking : Ancient Maya's Evolution of Consciousness and Contemporary Systems Thinking

NASA Astrophysics Data System (ADS)

Jere Lazanski, Tadeja

2010-11-01

Systems thinking as a modern approach for problem solving was revived after WWII even though it had been an ancient philosophy. We can track systems thinking back to antiquity. Making a distinction from Western rationalist traditions of philosophy, C. West Churchman often identified with the I Ching as a systems approach sharing a frame of reference similar to pre-Socratic philosophy and Heraclitus. In this paper, we will compare the evolutionary system of consciousness, which was presented in the Tun calendar of Mayan Indians and contemporary systems theory and systems thinking, which is nothing else but highly evolved human consciousness in society. We will present Mayan calendar systems to contemporary systems thinking principles and explain the answer to the Ackoff's judgment on four hundred years of analytical thinking as the dominant mode of society. We will use the methods of historical comparison and a method of a systems approach. We will point out the big picture and Mayan divine plan as main systems principles. The Mayan numerical system and long count units has been proven as one of the most accurate systems for describing the present and future of the civilization in which we have all evolved. We will also explain the Mayan nine-level pyramids system that represents the evolutionary system, i.e. the consciousness, which in our time shows the actual level of human consciousness. Deriving from all described, we will show the main systems principles, discussed by contemporary systems authors and Mayan systems principles, which differ only in one expression—they named "the big picture" as "the divine plan". The final results can be perfectly applied to the society we live in. Seeing the world from the big picture point of view is reaching a level of awareness, in which linear thinking is replaced by systems thinking. The Mayans explained that the civilization would achieve the system of conscious co-creation. We can claim that linear thinking guides us to a limited consciousness, whereas systems thinking opens the possibilities of conscious co-creation for the benefits of sustainable society and future of the planet.

7 CFR 1753.68 - Purchasing special equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... operating systems to increase system capacity that require components made by the manufacturer of the... operating systems in the borrower's system, or with complete systems of special equipment from other... AGRICULTURE TELECOMMUNICATIONS SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Purchase and Installation of...

7 CFR 1753.68 - Purchasing special equipment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... operating systems to increase system capacity that require components made by the manufacturer of the... operating systems in the borrower's system, or with complete systems of special equipment from other... AGRICULTURE TELECOMMUNICATIONS SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Purchase and Installation of...

7 CFR 1753.68 - Purchasing special equipment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... operating systems to increase system capacity that require components made by the manufacturer of the... operating systems in the borrower's system, or with complete systems of special equipment from other... AGRICULTURE TELECOMMUNICATIONS SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Purchase and Installation of...

7 CFR 1753.68 - Purchasing special equipment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... operating systems to increase system capacity that require components made by the manufacturer of the... operating systems in the borrower's system, or with complete systems of special equipment from other... AGRICULTURE TELECOMMUNICATIONS SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Purchase and Installation of...

7 CFR 1753.68 - Purchasing special equipment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... operating systems to increase system capacity that require components made by the manufacturer of the... operating systems in the borrower's system, or with complete systems of special equipment from other... AGRICULTURE TELECOMMUNICATIONS SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Purchase and Installation of...

A Sustainable, Reliable Mission-Systems Architecture that Supports a System of Systems Approach to Space Exploration

NASA Technical Reports Server (NTRS)

Watson, Steve; Orr, Jim; O'Neil, Graham

2004-01-01

A mission-systems architecture based on a highly modular "systems of systems" infrastructure utilizing open-standards hardware and software interfaces as the enabling technology is absolutely essential for an affordable and sustainable space exploration program. This architecture requires (a) robust communication between heterogeneous systems, (b) high reliability, (c) minimal mission-to-mission reconfiguration, (d) affordable development, system integration, and verification of systems, and (e) minimum sustaining engineering. This paper proposes such an architecture. Lessons learned from the space shuttle program are applied to help define and refine the model.

Utilizing Fission Technology to Enable Rapid and Affordable Access to any Point in the Solar System

NASA Technical Reports Server (NTRS)

Houts, Mike; Bonometti, Joe; Morton, Jeff; Hrbud, Ivana; Bitteker, Leo; VanDyke, Melissa; Godfroy, T.; Pedersen, K.; Dobson, C.; Patton, B.;

ISTAR: Intelligent System for Telemetry Analysis in Real-time

NASA Technical Reports Server (NTRS)

Simmons, Charles

1994-01-01

The intelligent system for telemetry analysis in real-time (ISTAR) is an advanced vehicle monitoring environment incorporating expert systems, analysis tools, and on-line hypermedia documentation. The system was developed for the Air Force Space and Missile Systems Center (SMC) in Los Angeles, California, in support of the inertial upper stage (IUS) booster vehicle. Over a five year period the system progressed from rapid prototype to operational system. ISTAR has been used to support five IUS missions and countless mission simulations. There were a significant number of lessons learned with respect to integrating an expert system capability into an existing ground system.

Portable data flow in UNIX

NASA Astrophysics Data System (ADS)

Fox, R.; Molen, A. Vander; Hannuschke, S.

1994-02-01

We describe the dataflow of a nuclear physics data acquisition system. The system features a high speed active routing subsystem which allows an arbitrary number of data producers to contribute data to the system. Data are then routed to an arbitrary number of data consumers. Low overhead route-by-reference mechanisms are used to allow high rate operations. The system has been ported to a variety of UNIX systems. Timings are given for the routing component of the system on several systems. Finally, we give an example of a set of programs which can be added to the system to produce a complete data acquisition system.

Electrical power systems for Space Station

NASA Technical Reports Server (NTRS)

Simon, W. E.

1984-01-01

Major challenges in power system development are described. Evolutionary growth, operational lifetime, and other design requirements are discussed. A pictorial view of weight-optimized power system applications shows which systems are best for missions of various lengths and required power level. Following definition of the major elements of the electrical power system, an overview of element options and a brief technology assessment are presented. Selected trade-study results show end-to-end system efficiencies, required photovoltaic power capability as a function of energy storage system efficiency, and comparisons with other systems such as a solar dynamic power system.

System review: a method for investigating medical errors in healthcare settings.

PubMed

Alexander, G L; Stone, T T

2000-01-01

System analysis is a process of evaluating objectives, resources, structure, and design of businesses. System analysis can be used by leaders to collaboratively identify breakthrough opportunities to improve system processes. In healthcare systems, system analysis can be used to review medical errors (system occurrences) that may place patients at risk for injury, disability, and/or death. This study utilizes a case management approach to identify medical errors. Utilizing an interdisciplinary approach, a System Review Team was developed to identify trends in system occurrences, facilitate communication, and enhance the quality of patient care by reducing medical errors.

Space station integrated propulsion and fluid systems study. Space station program fluid management systems databook

NASA Technical Reports Server (NTRS)

Bicknell, B.; Wilson, S.; Dennis, M.; Lydon, M.

1988-01-01

Commonality and integration of propulsion and fluid systems associated with the Space Station elements are being evaluated. The Space Station elements consist of the core station, which includes habitation and laboratory modules, nodes, airlocks, and trusswork; and associated vehicles, platforms, experiments, and payloads. The program is being performed as two discrete tasks. Task 1 investigated the components of the Space Station architecture to determine the feasibility and practicality of commonality and integration among the various propulsion elements. This task was completed. Task 2 is examining integration and commonality among fluid systems which were identified by the Phase B Space Station contractors as being part of the initial operating capability (IOC) and growth Space Station architectures. Requirements and descriptions for reference fluid systems were compiled from Space Station documentation and other sources. The fluid systems being examined are: an experiment gas supply system, an oxygen/hydrogen supply system, an integrated water system, the integrated nitrogen system, and the integrated waste fluids system. Definitions and descriptions of alternate systems were developed, along with analyses and discussions of their benefits and detriments. This databook includes fluid systems descriptions, requirements, schematic diagrams, component lists, and discussions of the fluid systems. In addition, cost comparison are used in some cases to determine the optimum system for a specific task.

Power System Mass Analysis for Hydrogen Reduction Oxygen Production on the Lunar Surface

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.

2009-01-01

The production of oxygen from the lunar regolith requires both thermal and electrical power in roughly similar proportions. This unique power requirement is unlike most applications on the lunar surface. To efficiently meet these requirements, both solar PV array and solar concentrator systems were evaluated. The mass of various types of photovoltaic and concentrator based systems were calculated to determine the type of power system that provided the highest specific power. These were compared over a range of oxygen production rates. Also a hybrid type power system was also considered. This system utilized a photovoltaic array to produce the electrical power and a concentrator to provide the thermal power. For a single source system the three systems with the highest specific power were a flexible concentrator/Stirling engine system, a rigid concentrator/Stirling engine system and a tracking triple junction solar array system. These systems had specific power values of 43, 34, and 33 W/kg, respectively. The hybrid power system provided much higher specific power values then the single source systems. The best hybrid combinations were the triple junction solar array with the flexible concentrator and the rigid concentrator. These systems had a specific power of 81 and 68 W/kg, respectively.

Putting the system back into systems change: a framework for understanding and changing organizational and community systems.

PubMed

Foster-Fishman, Pennie G; Nowell, Branda; Yang, Huilan

2007-06-01

Systems change has emerged as a dominant frame through which local, state, and national funders and practitioners across a wide array of fields approach their work. In most of these efforts, change agents and scholars strive to shift human services and community systems to create better and more just outcomes and improve the status quo. Despite this, there is a dearth of frameworks that scholars, practitioners, and funders can draw upon to aid them in understanding, designing, and assessing this process from a systemic perspective. This paper provides one framework--grounded in systems thinking and change literatures--for understanding and identifying the fundamental system parts and interdependencies that can help to explain system functioning and leverage systems change. The proposed framework highlights the importance of attending to both the deep and apparent structures within a system as well as the interactions and interdependencies among these system parts. This includes attending to the dominant normative, resource, regulative, and operational characteristics that dictate the behavior and lived experiences of system members. The value of engaging critical stakeholders in problem definition, boundary construction, and systems analysis are also discussed. The implications of this framework for systems change researchers and practitioners are discussed.

Decoupling control of vehicle chassis system based on neural network inverse system

NASA Astrophysics Data System (ADS)

Wang, Chunyan; Zhao, Wanzhong; Luan, Zhongkai; Gao, Qi; Deng, Ke

2018-06-01

Steering and suspension are two important subsystems affecting the handling stability and riding comfort of the chassis system. In order to avoid the interference and coupling of the control channels between active front steering (AFS) and active suspension subsystems (ASS), this paper presents a composite decoupling control method, which consists of a neural network inverse system and a robust controller. The neural network inverse system is composed of a static neural network with several integrators and state feedback of the original chassis system to approach the inverse system of the nonlinear systems. The existence of the inverse system for the chassis system is proved by the reversibility derivation of Interactor algorithm. The robust controller is based on the internal model control (IMC), which is designed to improve the robustness and anti-interference of the decoupled system by adding a pre-compensation controller to the pseudo linear system. The results of the simulation and vehicle test show that the proposed decoupling controller has excellent decoupling performance, which can transform the multivariable system into a number of single input and single output systems, and eliminate the mutual influence and interference. Furthermore, it has satisfactory tracking capability and robust performance, which can improve the comprehensive performance of the chassis system.

Software fault tolerance in computer operating systems

NASA Technical Reports Server (NTRS)

Iyer, Ravishankar K.; Lee, Inhwan

1994-01-01

This chapter provides data and analysis of the dependability and fault tolerance for three operating systems: the Tandem/GUARDIAN fault-tolerant system, the VAX/VMS distributed system, and the IBM/MVS system. Based on measurements from these systems, basic software error characteristics are investigated. Fault tolerance in operating systems resulting from the use of process pairs and recovery routines is evaluated. Two levels of models are developed to analyze error and recovery processes inside an operating system and interactions among multiple instances of an operating system running in a distributed environment. The measurements show that the use of process pairs in Tandem systems, which was originally intended for tolerating hardware faults, allows the system to tolerate about 70% of defects in system software that result in processor failures. The loose coupling between processors which results in the backup execution (the processor state and the sequence of events occurring) being different from the original execution is a major reason for the measured software fault tolerance. The IBM/MVS system fault tolerance almost doubles when recovery routines are provided, in comparison to the case in which no recovery routines are available. However, even when recovery routines are provided, there is almost a 50% chance of system failure when critical system jobs are involved.

Platelet collection efficiencies of three different platelet-rich plasma preparation systems.

PubMed

Aydin, Fatma; Pancar Yuksel, Esra; Albayrak, Davut

2015-06-01

Different systems have been used for the preparation of platelet-rich plasma (PRP), but platelet collection efficiencies of these systems are not clear. To evaluate the platelet collection efficiencies of three different PRP preparation systems. Blood samples were obtained from the same 16 volunteers for each system. The samples were centrifuged and PRP was prepared by three systems. The ratio of the total number of platelets in PRP to the total number of platelets of the venous blood sample of the patient expressed in percentage was named as platelet collection efficiency and calculated for each system. Mean platelet collection efficiencies were 66.6 (min: 56.9, max: 76.9), 58.3 (min: 27.3, max: 102.8), 50.8 (min: 27.2, max: 73) for top and bottom bag system, system using citrated tube, and the system using tube with Ficoll and cell extraction kit, respectively. Statistically significant difference was found only between the platelet collection efficiencies of systems using the tube with ficoll and cell extraction kit and the top and bottom bag system (p = 0.002). All three systems could be used for PRP preparation, but top and bottom bag system offers a slight advantage over the system using Ficoll and cell extraction kit regarding the platelet collection efficiency.

Intelligent systems technology infrastructure for integrated systems

NASA Technical Reports Server (NTRS)

Lum, Henry, Jr.

1991-01-01

Significant advances have occurred during the last decade in intelligent systems technologies (a.k.a. knowledge-based systems, KBS) including research, feasibility demonstrations, and technology implementations in operational environments. Evaluation and simulation data obtained to date in real-time operational environments suggest that cost-effective utilization of intelligent systems technologies can be realized for Automated Rendezvous and Capture applications. The successful implementation of these technologies involve a complex system infrastructure integrating the requirements of transportation, vehicle checkout and health management, and communication systems without compromise to systems reliability and performance. The resources that must be invoked to accomplish these tasks include remote ground operations and control, built-in system fault management and control, and intelligent robotics. To ensure long-term evolution and integration of new validated technologies over the lifetime of the vehicle, system interfaces must also be addressed and integrated into the overall system interface requirements. An approach for defining and evaluating the system infrastructures including the testbed currently being used to support the on-going evaluations for the evolutionary Space Station Freedom Data Management System is presented and discussed. Intelligent system technologies discussed include artificial intelligence (real-time replanning and scheduling), high performance computational elements (parallel processors, photonic processors, and neural networks), real-time fault management and control, and system software development tools for rapid prototyping capabilities.

Design Validation Methodology Development for an Aircraft Sensor Deployment System

NASA Astrophysics Data System (ADS)

Wowczuk, Zenovy S.

The OCULUS 1.0 Sensor Deployment concept design, was developed in 2004 at West Virginia University (WVU), outlined the general concept of a deployment system to be used on a C-130 aircraft. As a sequel, a new system, OCULUS 1.1, has been developed and designed. The new system transfers the concept system design to a safety of flight design, and also enhanced to a pre-production system to be used as the test bed to gain full military certification approval. The OCULUS 1.1 system has an implemented standard deployment system/procedure to go along with a design suited for military certification and implementation. This design process included analysis of the system's critical components and the generation of a critical component holistic model to be used as an analysis tool for future payload modification made to the system. Following the completion of the OCULUS 1.1 design, preparations and procedures for obtaining military airworthiness certification are described. The airworthiness process includes working with the agency overseeing all modifications to the normal operating procedures made to military C-130 aircraft and preparing the system for an experimental flight test. The critical steps in his process include developing a complete documentation package that details the analysis performed on the OCULUS 1.1 system and also the design of experiment flight test plan to analyze the system. Following the approval of the documentation and design of experiment an experimental flight test of the OCULUS 1.1 system was performed to verify the safety and airworthiness of the system. This test proved successfully that the OCULUS 1.1 system design was airworthy and approved for military use. The OCULUS 1.1 deployment system offers an open architecture design that is ideal for use as a sensor testing platform for developmental airborne sensors. The system's patented deployment methodology presents a simplistic approach to reaching the systems final operating position which offers the most robust field of view area of rear ramp deployment systems.

Development and Testing of a Prototype Grid-Tied Photovoltaic Power System

NASA Technical Reports Server (NTRS)

Eichenberg, Dennis J.

2009-01-01

The NASA Glenn Research Center (GRC) has developed and tested a prototype 2 kW DC grid-tied photovoltaic (PV) power system at the Center. The PV system has generated in excess of 6700 kWh since operation commenced in July 2006. The PV system is providing power to the GRC grid for use by all. Operation of the prototype PV system has been completely trouble free. A grid-tied PV power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provide valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. Based upon the success of the prototype PV system, additional PV power system expansion at GRC is under consideration. The prototype grid-tied PV power system was successfully designed and developed which served to validate the basic principles described, and the theoretical work that was performed. The report concludes that grid-tied photovoltaic power systems are reliable, maintenance free, long life power systems, and are of significant value to NASA and the community.

Validity of Torque-Data Collection at Multiple Sites: A Framework for Collaboration on Clinical-Outcomes Research in Sports Medicine.

PubMed

Kuenze, Christopher; Eltouhky, Moataz; Thomas, Abbey; Sutherlin, Mark; Hart, Joseph

2016-05-01

Collecting torque data using a multimode dynamometer is common in sports-medicine research. The error in torque measurements across multiple sites and dynamometers has not been established. To assess the validity of 2 calibration protocols across 3 dynamometers and the error associated with torque measurement for each system. Observational study. 3 university laboratories at separate institutions. 2 Biodex System 3 dynamometers and 1 Biodex System 4 dynamometer. System calibration was completed using the manufacturer-recommended single-weight method and an experimental calibration method using a series of progressive weights. Both calibration methods were compared with a manually calculated theoretical torque across a range of applied weights. Relative error, absolute error, and percent error were calculated at each weight. Each outcome variable was compared between systems using 95% confidence intervals across low (0-65 Nm), moderate (66-110 Nm), and high (111-165 Nm) torque categorizations. Calibration coefficients were established for each system using both calibration protocols. However, within each system the calibration coefficients generated using the single-weight (System 4 = 2.42 [0.90], System 3a = 1.37 [1.11], System 3b = -0.96 [1.45]) and experimental calibration protocols (System 4 = 3.95 [1.08], System 3a = -0.79 [1.23], System 3b = 2.31 [1.66]) were similar and displayed acceptable mean relative error compared with calculated theoretical torque values. Overall, percent error was greatest for all 3 systems in low-torque conditions (System 4 = 11.66% [6.39], System 3a = 6.82% [11.98], System 3b = 4.35% [9.49]). The System 4 significantly overestimated torque across all 3 weight increments, and the System 3b overestimated torque over the moderate-torque increment. Conversion of raw voltage to torque values using the single-calibration-weight method is valid and comparable to a more complex multiweight calibration process; however, it is clear that calibration must be done for each individual system to ensure accurate data collection.

[Review of visual display system in flight simulator].

PubMed

Xie, Guang-hui; Wei, Shao-ning

2003-06-01

Visual display system is the key part and plays a very important role in flight simulators and flight training devices. The developing history of visual display system is recalled and the principle and characters of some visual display systems including collimated display systems and back-projected collimated display systems are described. The future directions of visual display systems are analyzed.

Improving Systems Engineering Effectiveness in Rapid Response Development Environments

DTIC Science & Technology

2012-06-02

environments where large, complex, brownfield systems of systems are evolved through parallel development of new capabilities in response to external, time...license 14. ABSTRACT Systems engineering is often ineffective in development environments where large, complex, brownfield systems of systems are...IEEE Press, Hoboken, NJ, 2008 [18] Boehm, B.: Applying the Incremental Commitment Model to Brownfield Systems Development, Proceedings, CSER 2009

Expert systems in civil engineering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kostem, C.N.; Maher, M.L.

1986-01-01

This book presents the papers given at a symposium on expert systems in civil engineering. Topics considered at the symposium included problem solving using expert system techniques, construction schedule analysis, decision making and risk analysis, seismic risk analysis systems, an expert system for inactive hazardous waste site characterization, an expert system for site selection, knowledge engineering, and knowledge-based expert systems in seismic analysis.

Methodology. Volume 3

DTIC Science & Technology

1997-02-01

modification, test, and production System operation, support, and maturation Weapon System Life Cycle Management Weapon systems Attainment...information management systems • Weapon systems electronics context – Focuses on many types of interactions » Information » Jamming » Support – Deals with...concepts • C4I context – Focuses on C4I information management systems – Defines the C4I systems and their information interchange requirements

Manufacturing Laboratory for Next Generation Engineers

DTIC Science & Technology

2013-12-16

automated CNC machines, rapid prototype systems, robotic assembly systems, metrology , and non-traditional systems such as a waterjet cutter, EDM machine...CNC machines, rapid prototype systems, robotic assembly systems, metrology , and non-traditional systems such as a waterjet cutter, EDM machine, plasma...System Metrology and Quality Control Equipment - This area already had a CMM and other well known quality control instrumentation. It has been enhanced

36 CFR Appendix B to Part 1234 - Alternative Certified Fire-Safety Detection and Suppression System(s)

Code of Federal Regulations, 2012 CFR

2012-07-01

... the system at the base of the main sprinkler riser. l. Fire hydrants must be located within 250 feet... Suppression System(s) 1. General. This Appendix B contains information on the Fire-safety Detection and Suppression System(s) tested by NARA through independent live fire testing that are certified to meet the...

36 CFR Appendix B to Part 1234 - Alternative Certified Fire-Safety Detection and Suppression System(s)

Code of Federal Regulations, 2014 CFR

2014-07-01

... the system at the base of the main sprinkler riser. l. Fire hydrants must be located within 250 feet... Suppression System(s) 1. General. This Appendix B contains information on the Fire-safety Detection and Suppression System(s) tested by NARA through independent live fire testing that are certified to meet the...

36 CFR Appendix B to Part 1234 - Alternative Certified Fire-Safety Detection and Suppression System(s)

Code of Federal Regulations, 2013 CFR

2013-07-01

... the system at the base of the main sprinkler riser. l. Fire hydrants must be located within 250 feet... Suppression System(s) 1. General. This Appendix B contains information on the Fire-safety Detection and Suppression System(s) tested by NARA through independent live fire testing that are certified to meet the...

SSCR Automated Manager (SAM) release 1. 1 reference manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-10-01

This manual provides instructions for using the SSCR Automated Manager (SAM) to manage System Software Change Records (SSCRs) online. SSCRs are forms required to document all system software changes for the Martin Marietta Energy Systems, Inc., Central computer systems. SAM, a program developed at Energy Systems, is accessed through IDMS/R (Integrated Database Management System) on an IBM system.

Telematics and satellites. Part 1: Information systems

NASA Astrophysics Data System (ADS)

Burke, W. R.

1980-06-01

Telematic systems are identified and described. The applications are examined emphasizing the role played by satellite links. The discussion includes file transfer, examples of distributed processor systems, terminal communication, information retrieval systems, office information systems, electronic preparation and publishing of information, electronic systems for transfer of funds, electronic mail systems, record file transfer characteristics, intra-enterprise networks, and inter-enterprise networks.

Rethinking the Systems Engineering Process in Light of Design Thinking

DTIC Science & Technology

2016-04-30

systems engineering process models (Blanchard & Fabrycky, 1990) and the majority of engineering design education (Dym et al., 2005). The waterfall model ...Engineering Career Competency Model Clifford Whitcomb, Systems Engineering Professor, NPS Corina White, Systems Engineering Research Associate, NPS...Postgraduate School (NPS) in Monterey, CA. He teaches and conducts research in the design of enterprise systems, systems modeling , and system

A Model for Communications Satellite System Architecture Assessment

DTIC Science & Technology

2011-09-01

This is shown in Equation 4. The total system cost includes all development, acquisition, fielding, operations, maintenance and upgrades, and system...protection. A mathematical model was implemented to enable the analysis of communications satellite system architectures based on multiple system... implemented to enable the analysis of communications satellite system architectures based on multiple system attributes. Utilization of the model in

Systems in the Foundations of Information Systems Course to Retain Students and to Support the IS 2010 Model Curricula

ERIC Educational Resources Information Center

Slauson, Gayla Jo; Carpenter, Donald; Snyder, Johnny

2011-01-01

Systems in the Foundations of Information Systems course can be used to connect with students in computer information systems programs; a systematic approach to beginning student relationship management in this course is helpful. The authors suggest that four systems be created in the Foundations Course. These theoretical systems include an…

How to Construct Curricula for Finance Professional under Credit System in China

ERIC Educational Resources Information Center

Ma, Yuanyuan

2014-01-01

As a kind of teaching system, the credit system is constructed according to the elective system. It is benefit for improving teaching in implementing credit system. There are still some constraints during the transition from the academic year system to the credit one. In this paper, we shall first briefly introduce the bottleneck of credit system.…

An Incremental Life-cycle Assurance Strategy for Critical System Certification

DTIC Science & Technology

2014-11-04

for Safe Aircraft Operation Embedded software systems introduce a new class of problems not addressed by traditional system modeling & analysis...Platform Runtime Architecture Application Software Embedded SW System Engineer Data Stream Characteristics Latency jitter affects control behavior...do system level failures still occur despite fault tolerance techniques being deployed in systems ? Embedded software system as major source of

The Design and Implement of Tourism Information System Based on GIS

NASA Astrophysics Data System (ADS)

Chunchang, Fu; Nan, Zhang

From the geographical information system concept, discusses the main contents of the geographic information system, and the current of the geographic information system key technological measures of tourism information system, the application of tourism information system for specific requirements and goals, and analyzes a relational database model based on the tourist information system in GIS application methods of realization.

A 50 kilowatt distributed grid-connected photovoltaic generation system for the University of Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chowdhury, B.H.; Muknahallipatna, S.; Cupal, J.J.

The University of Wyoming (UW) campus is serving as the site for a 50 kilowatt solar photovoltaic (PV) system. Three sub-systems were sited and built on the UW campus in 1996. The first sub-system, a 10 kW roof-integrated system of PV roof tiles is located on the roof of the Engineering building. The second sub-system--a 5 kW rack-mounted, ballasted PV system is on a walkway roof of the Engineering building. The third sub-system is a 35 kW shade structure system and located adjacent to the parking lot of the university`s football stadium. The three sub-systems differ in their design strategymore » since each is being used for research and education at the university. Each sub-system, being located at some distance away from one another, supplies a different part of the campus grid. Efforts continue at setting up a central monitoring system which will receive data remotely from all locations. A part of this monitoring system is complete. While the initial monitoring data shows satisfactory performance, a number of reliability problems with PV modules and inverters have delayed full functionality of the system.« less

From prototype to production system: lessons learned from the evolution of the SignOut System at Mount Sinai Medical Center.

PubMed

Kushniruk, Andre; Karson, Tom; Moore, Carlton; Kannry, Joseph

2003-01-01

Approaches to the development of information systems in large health care institutions range from prototyping to conventional development of large scale production systems. This paper discusses the development of the SignOut System at Mount Sinai Medical Center, which was designed in 1997 to capture vital resident information. Local need quickly outstripped proposed delays for building a production system and a prototype system quickly became a production system. By the end of 2002 the New SignOut System was built to create an integrated application that was a true production system. In this paper we discuss the design and implementation issues in moving from a prototype to a production system. The production system had a number of advantages, including increased organizational visibility, integration into enterprise resource planning and full time staff for support. However, the prototype allowed for more rapid design and subsequent changes, less training, and equal to or superior help desk support. It is argued that healthcare IT systems may need characteristics of both prototype and production system development to rapidly meet the changing and different needs of healthcare user populations.

Solution to problems of bacterial impurity of heating systems

NASA Astrophysics Data System (ADS)

Sharapov, V. I.; Zamaleev, M. M.

2015-09-01

The article describes the problems of the operation of open and closed district heating systems related to the bacteriological contamination of heating-system water. It is noted that district heating systems are basically safe in sanitary epidemiological terms. Data on the dangers of sulfide contamination of heating systems are given. It is shown that the main causes of the development of sulfate-reducing and iron bacteria in heating systems are a significant biological contamination of source water to fuel heating systems, which is determined by water oxidizability, and a low velocity of the motion of heating-system water in the heating system elements. A case of sulfide contamination of a part of the outdoor heat-supply system of the city of Ulyanovsk is considered in detail. Measures for cleaning pipelines and heating system equipment from the waste products of sulfate-reducing bacteria and iron bacteria and for improving the quality of heating-system water by organizing the hydraulic and water-chemistry condition that makes it possible to avoid the bacteriological contamination of heating systems are proposed. The positive effect of sodium silicate on the prevention of sulfide contamination of heating systems is shown.

Industrial Energy Training and Certification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glatt, Sandy; Cox, Daryl; Nimbalkar, Sachin U.

Compressed air systems, ammonia refrigeration systems, chilled water systems, steam systems, process heating systems, combined heat and power systems, pump systems and fan systems are major industrial energy systems commonly found in manufacturing facilities. Efficiency of these systems contributes significantly to whole facilities' energy performance. On the national, even international level, well-structured training and highly recognized certification programs help develop a highly-skilled and qualified workforce to maintain and improve facilities' energy performance, particularly as technologies within these systems become more advanced. The purpose of this paper is to review currently available training and certification programs focusing on these systems andmore » to identify the gap between market's needs and currently available programs. Three major conclusions are: first, most training programs focus on operations, maintenance, safety and design although some briefly touch the energy performance aspect; second, except CRES by RETA and PSA Certificate and PSAP Master Certification by HI, no other certifications had been found emphasizing on knowledge and skills for improving and maintaining these systems' energy performance; third, developing energy efficiency focused training and ANSI accredited certification programs on these energy systems will fill the gap between market's needs and currently available programs.« less

Cognitive engineering models: A prerequisite to the design of human-computer interaction in complex dynamic systems

NASA Technical Reports Server (NTRS)

Mitchell, Christine M.

1993-01-01

This chapter examines a class of human-computer interaction applications, specifically the design of human-computer interaction for the operators of complex systems. Such systems include space systems (e.g., manned systems such as the Shuttle or space station, and unmanned systems such as NASA scientific satellites), aviation systems (e.g., the flight deck of 'glass cockpit' airplanes or air traffic control) and industrial systems (e.g., power plants, telephone networks, and sophisticated, e.g., 'lights out,' manufacturing facilities). The main body of human-computer interaction (HCI) research complements but does not directly address the primary issues involved in human-computer interaction design for operators of complex systems. Interfaces to complex systems are somewhat special. The 'user' in such systems - i.e., the human operator responsible for safe and effective system operation - is highly skilled, someone who in human-machine systems engineering is sometimes characterized as 'well trained, well motivated'. The 'job' or task context is paramount and, thus, human-computer interaction is subordinate to human job interaction. The design of human interaction with complex systems, i.e., the design of human job interaction, is sometimes called cognitive engineering.

Electrical Power Systems for NASA's Space Transportation Program

NASA Technical Reports Server (NTRS)

Lollar, Louis F.; Maus, Louis C.

1998-01-01

Marshall Space Flight Center (MSFC) is the National Aeronautics and Space Administration's (NASA) lead center for space transportation systems development. These systems include earth to orbit launch vehicles, as well as vehicles for orbital transfer and deep space missions. The tasks for these systems include research, technology maturation, design, development, and integration of space transportation and propulsion systems. One of the key elements in any transportation system is the electrical power system (EPS). Every transportation system has to have some form of electrical power and the EPS for each of these systems tends to be as varied and unique as the missions they are supporting. The Preliminary Design Office (PD) at MSFC is tasked to perform feasibility analyses and preliminary design studies for new projects, particularly in the space transportation systems area. All major subsystems, including electrical power, are included in each of these studies. Three example systems being evaluated in PD at this time are the Liquid Fly Back Booster (LFBB) system, the Human Mission to Mars (HMM) study, and a tether based flight experiment called the Propulsive Small Expendable Deployer System (ProSEDS). These three systems are in various stages of definition in the study phase.