Sample records for cane fiberboard samples

  1. FIFTH STATUS REPORT: TESTING OF AGED SOFTWOOD FIBERBOARD MATERIAL FOR THE 9975 SHIPPING PACKAGE

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.; Skidmore, E.; Dunn, K.

    Samples have been prepared from a 9975 lower fiberboard subassembly fabricated from softwood fiberboard. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples, with a few differences. Some softwood fiberboard properties tend to degrade faster in elevated humidity environments, while some cane fiberboard properties degrade faster in the hotter dry environments. As a result, it is premature to assume both materials will agemore » at the same rates, and the preliminary aging models developed for cane fiberboard might not apply to softwood fiberboard. However, it is expected that both cane and softwood fiberboard assemblies will perform satisfactorily in conforming packages stored in a typical KAC storage environment for up to 15 years. Aging and testing of softwood fiberboard will continue and additional data will be collected. Additional samples will be added to each aging environment, to support development of an aging model specific to softwood fiberboard. Post-conditioning data have been measured on samples from a single softwood fiberboard assembly, and baseline data are also available from a limited number of vendor-provided samples. This provides minimal information on the possible sample-to-sample variation exhibited by softwood fiberboard. Data to date are generally consistent with the range seen in cane fiberboard, but some portions of the data trends are skewed toward the lower end of that range. Two additional softwood fiberboard source packages have been obtained and will begin to provide data on the range of variability of this material.« less

  2. Sixth Status Report: Testing of Aged Softwood Fiberboard Material for the 9975 Shipping Package

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    Samples have been prepared from several 9975 lower fiberboard subassemblies fabricated from softwood fiberboard. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples, with a few differences. Some softwood fiberboard properties tend to degrade faster in some environments, while some cane fiberboard properties degrade faster in the two most aggressive environments. As a result, it is premature to assume both materials will agemore » at the same rates, and the preliminary aging models developed for cane fiberboard might not apply to softwood fiberboard. However, it is expected that both cane and softwood fiberboard assemblies will perform satisfactorily in conforming packages stored in a typical KAC storage environment for up to 15 years. Samples from an additional 3 softwood fiberboard assemblies have begun aging during the past year to provide information on the variability of softwood fiberboard behavior. Aging and testing of softwood fiberboard will continue and additional data will be collected to support development of an aging model specific to softwood fiberboard.« less

  3. FIRST STATUS REPORT: TESTING OF AGED SOFTWOOD FIBERBOARD MATERIAL FOR THE 9975 SHIPPING PACKAGE

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    2010-01-08

    Samples have been prepared from a softwood fiberboard lower subassembly. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples. Some of the observed differences result from the limited exposure periods of the softwood fiberboard samples, and the impact of seasonal humidity levels. Testing following additional conditioning will continue and should eliminate this bias. Post-conditioning data have been measured on a single softwood fiberboardmore » assembly, and baseline data are also available from a limited number of vendor-provided samples. This provides minimal information on the possible sample-to-sample variation exhibited by softwood fiberboard. Data to date are generally consistent with the range seen in cane fiberboard, but much of the compression strength data tends toward the lower end of that range. Further understanding of the variability of softwood fiberboard properties will require testing of additional material. Cane fiberboard wall sheathing is specified for thermal insulation and impact resistance in 9975 shipping packages. Softwood fiberboard manufactured by Knight-Celotex was approved as an acceptable substitute for transportation in 2008. Data in the literature [1] show a consistent trend in thermal properties of fiberboard as a function of temperature, density and/or moisture content regardless of material source. Thermal and mechanical properties were measured for un-aged softwood fiberboard samples, and found to be sufficiently similar to those of un-aged cane fiberboard to support the acceptance of 9975 packages with softwood fiberboard overpack into KAMS for storage. The continued acceptability of aged softwood fiberboard to meet KAMS storage requirements was the subject of subsequent activities. This is an interim status report for experiments carried out per Task Technical Plan WSRC-TR-2008-00024 [2], which is part of the comprehensive 9975 package surveillance program [3]. The primary goal of this task is to validate the preliminary assessment that Knight-Celotex softwood fiberboard is an acceptable substitute for cane fiberboard in the 9975 shipping package overpack, and that the long-term performance of these two materials in a storage environment is comparable.« less

  4. DEMONSTRATION OF EQUIVALENCY OF CANE AND SOFTWOOD BASED CELOTEX FOR MODEL 9975 SHIPPING PACKAGES

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Watkins, R; Jason Varble, J

    2008-05-27

    Cane-based Celotex{trademark} has been used extensively in various Department of Energy (DOE) packages as a thermal insulator and impact absorber. Cane-based Celotex{trademark} fiberboard was only manufactured by Knight-Celotex Fiberboard at their Marrero Plant in Louisiana. However, Knight-Celotex Fiberboard shut down their Marrero Plant in early 2007 due to impacts from hurricane Katrina and other economic factors. Therefore, cane-based Celotex{trademark} fiberboard is no longer available for use in the manufacture of new shipping packages requiring the material as a component. Current consolidation plans for the DOE Complex require the procurement of several thousand new Model 9975 shipping packages requiring cane-based Celotex{trademark}more » fiberboard. Therefore, an alternative to cane-based Celotex{trademark} fiberboard is needed. Knight-Celotex currently manufactures Celotex{trademark} fiberboard from other cellulosic materials, such as hardwood and softwood. A review of the relevant literature has shown that softwood-based Celotex{trademark} meets all parameters important to the Model 9975 shipping package.« less

  5. CANE FIBERBOARD DEGRADATION WITHIN THE 9975 SHIPPING PACKAGE DURING LONG-TERM STORAGE APPLICATION

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.; Dunn, K.; Hackney, B.

    The 9975 shipping package is used as part of the configuration for long-term storage of special nuclear materials in the K Area Complex at the Savannah River Site. The cane fiberboard overpack in the 9975 package provides thermal insulation, impact absorption and criticality control functions relevant to this application. The Savannah River National Laboratory has conducted physical, mechanical and thermal tests on aged fiberboard samples to identify degradation rates and support the development of aging models and service life predictions in a storage environment. This paper reviews the data generated to date, and preliminary models describing degradation rates of canemore » fiberboard in elevated temperature – elevated humidity environments.« less

  6. Status Report - Cane Fiberboard Properties And Degradation Rates For Storage Of The 9975 Shipping Package In KAC

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    Thermal, mechanical and physical properties have been measured on cane fiberboard samples following accelerated aging for up to approximately 10 years. The aging environments have included elevated temperature < 250 ºF (the maximum allowed service temperature for fiberboard in 9975 packages) and elevated humidity. The results from this testing have been analyzed, and aging models fit to the data. Correlations relating several properties (thermal conductivity, energy absorption, weight, dimensions and density) to their rate of change in potential storage environments have been developed. Combined with an estimate of the actual conditions the fiberboard experiences in KAC, these models allow developmentmore » of service life predictions.« less

  7. WHITE PAPER: DEMONSTRATION OF EQUIVALENCY OF CANE AND SOFTWOOD BASED CELOTEX FOR 9975 PACKAGING

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Varble, J

    2007-11-20

    Cane-based Celotex{trademark} has been used extensively in various DOE packages as a thermal insulator and impact absorber. Cane-based Celotex{trademark} for the 9975 was manufactured by Knight-Celotex Fiberboard at their Marrero Plant in Louisiana. However, Knight-Celotex Fiberboard shut down their Marrero Plant in early 2007 due to impacts from hurricane Katrina and other economic factors. Therefore, cane-based Celotex{trademark} is no longer available for use in the manufacture of new 9975 packages. Knight-Celotex Fiberboard has Celotex{trademark} manufacturing plants in Danville, VA and Sunbury, PA that use softwood and hardwood, respectively, as a raw material in the manufacturing of Celotex{trademark}. The purpose ofmore » this White Paper is to demonstrate that softwood-based Celotex{trademark} from the Knight-Celotex Danville Plant has performance equivalent to cane-based Celotex{trademark} from the Knight-Celotex Marrero Plant for transportation in a 9975 package.« less

  8. Humidity data for 9975 shipping packages with cane fiberboard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    The 9975 surveillance program is developing a technical basis to support extending the storage period of 9975 packages in K-Area Complex beyond the currently approved 15 years. A key element of this effort is developing a better understanding of degradation of the fiberboard assembly under storage conditions. This degradation is influenced greatly by the moisture content of the fiberboard, which is not well characterized on an individual package basis. Direct measurements of humidity and fiberboard moisture content have been made on two test packages with cane fiberboard and varying internal heat levels from 0 up to 19W. With an internalmore » heat load, a temperature gradient in the fiberboard assembly leads to varying relative humidity in the air around the fiberboard. However, the absolute humidity tends to remain approximately constant throughout the package. The moisture content of fiberboard varies under the influence of several phenomena. Changes in local fiberboard temperature (from an internal heat load) can cause fiberboard moisture changes through absorption or evaporation. Fiberboard degradation at elevated temperature will produce water as a byproduct. And the moisture level within the package is constantly seeking equilibrium with that of the surrounding room air, which varies on a daily and seasonal basis. One indicator of the moisture condition within a 9975 package might be obtained by measuring the relative humidity in the upper air space, by inserting a humidity probe through a caplug hole. However, the data indicate that for the higher internal heat loads (15 and 19 watts), a large variation in internal moisture conditions produces little or no variation in the air space relative humidity. Therefore, this approach does not appear to be sensitive to fiberboard moisture variations at the higher heat loads which are of most interest to maintaining fiberboard integrity.« less

  9. Status Report - Cane Fiberboard Properties and Degradation Rates for Storage of the 9975 Shipping Package in KAMS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Thermal, mechanical and physical properties have been measured on cane fiberboard samples following accelerated aging for up to approximately 7 years. The aging environments have included elevated temperature < 250 ?F (the maximum allowed service temperature for fiberboard in 9975 packages) and elevated humidity. The results from this testing have been analyzed, and aging models fit to the data. Correlations relating several properties (thermal conductivity, energy absorption, weight loss and height decrease) to their rate of change in potential storage environments have been developed. Combined with an estimate of the actual conditions the fiberboard experiences in KAMS, these models allowmore » development of service life predictions. Some of the predicted degradation rates presented in this report are relatively extreme. However, these relate to environments that do not exist within KAMS, or would be postulated only as upset conditions that would not likely persist for an extended period. For a typical package with ~10 watts internal heat load or less, and ambient temperatures below 90 ?F, the fiberboard experiences storage conditions less severe than any of the aging environments. Little or no degradation of the fiberboard is expected for typical storage conditions. It should be noted that the ultimate service life will be determined by the cumulative effect of degradation from all the conditions these packages might encounter. The assumptions and inputs behind the models in this report should be well understood before attempting to identify an actual service life in KAMS. Additional data continue to be collected to permit future refinements to the models and assumptions. For developing service life predictions, the ambient conditions within KAMS can be reasonably identified, and the temperature profiles within the various packages (with a range of heat loads and at varying locations within an array of packages) can be calculated. However, the humidity within the package is not as well characterized. While the outer drum does not provide an air-tight seal, it does greatly restrict the gain or loss of moisture in the fiberboard. Preliminary efforts have identified a relationship between the moisture content of fiberboard samples and the relative humidity of the surrounding air, but further work is needed in this area. Improvement in understanding this relationship might be realized with a change in the way humidity data are collected during field surveillances. It is recommended that the humidity be measured through a caplug hole before the package is removed from its storage location. The package would remain in thermal equilibrium, and anomalous humidity changes could be avoided. Further work should be performed to better define KAMS storage conditions and the environment within the 9975 shipping packages, and to identify appropriate limits for each property. This should be a joint effort by SRNL and NMM personnel. The results and model predictions presented in this report are applicable to 9975 packages with cane fiberboard overpack assemblies. A separate effort is underway to identify whether softwood fiberboard would behave similarly. In addition, the degradation models do not address the effects of non-conforming conditions such as the presence of excess moisture and mold, or beetle infestations.« less

  10. Examination of shipping package 9975-04985

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Package 9975-04985 was examined following the identification of several unexpected conditions during surveillance activities. A heavy layer of corrosion product on the shield and the shield outer diameter being larger that allowed by drawing tolerances contributed to a very tight fit between the upper fiberboard assembly and shield. The average corrosion rate for the shield is estimated to be 0.0018 inch/year or less, which falls within the bounding rate of 0.002 inch/year that has been previously recommended for these packages. Several apparent foreign objects were noted within the package. One object observed on the air shield was identified as tape.more » The other objects were comprised of mostly fine fibers from the cane fiberboard. It is postulated that the upper and lower fiberboard assemblies were able to rub against each other due to the upper fiberboard assembly being held tight to the shield, and a few stray cane chips became frayed under vibratory motions.« less

  11. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Stefek, T.; Daugherty, W.; Estochen, E.

    Compaction of lower layers in the fiberboard assembly has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and the behavior of the fiberboard during transport. In laboratory tests of cane fiberboard, higher moisture content has been shown to correspond to higher total compaction, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction compared tomore » a static load. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted to acquire immediate and cumulative changes in geometric data for various moisture levels. Two sample sets have undergone a complete dynamic test regimen, one set for 27 weeks, and the second set for 47 weeks. The dynamic input, data acquisition, test effects on sample dynamic parameters, and results from this test program are summarized and compared to regulatory specifications for dynamic loading. Compaction of the bottom fiberboard layers due to the accumulation of moisture is one possible cause of an increase in the axial gap at the top of the package. The net compaction of the bottom layers will directly add to the axial gap. The moisture which caused this compaction migrated from the middle region of the fiberboard assembly (which is typically the hottest). This will cause the middle region to shrink axially, which will also contribute directly to the axial gap. Measurement of the axial gap provides a screening tool for identifying significant change in the fiberboard condition. The data in this report provide a basis to evaluate the impact of moisture and fiberboard compaction on 9975 package performance during storage at the Savannah River Site (SRS).« less

  12. Humidity Data for 9975 Shipping Packages with Softwood Fiberboard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    The 9975 surveillance program is developing a technical basis to support extending the storage period of 9975 packages in K-Area Complex beyond the currently approved 15 years. A key element of this effort is developing a better understanding of degradation of the fiberboard assembly under storage conditions. This degradation is influenced greatly by the moisture content of the fiberboard, which is not well characterized on an individual package basis. Direct measurements of humidity and fiberboard moisture content have been made on two test packages with softwood fiberboard and varying internal heat levels from 0 up to 19W. Comparable measurements withmore » cane fiberboard have been reported previously. With an internal heat load, a temperature gradient in the fiberboard assembly leads to varying relative humidity in the air around the fiberboard. However, the absolute humidity tends to remain approximately constant throughout the package, especially at lower heat loads.« less

  13. Fiberboard humidity data for 9975 shipping packages

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    2015-07-31

    The 9975 surveillance program is identifying a technical basis to support extending the storage period of 9975 packages in KAC beyond the currently approved 15 years. A key element of this effort is developing a better understanding of degradation of the fiberboard assembly under storage conditions. This degradation is influenced greatly by the moisture content of the fiberboard, which is not well characterized on an individual package basis.Two efforts have been undertaken to better understand the levels and behavior of moisture within the fiberboard assemblies of the 9975 shipping package. In the first effort, an initial survey of humidity andmore » temperature in the upper air space of 26 packages stored in KAC was made. The data collected within this first effort help to illustrate how the upper air space humidity varies with the local ambient temperature and package heat load. In the second effort, direct measurements of two test packages are providing a correlation between humidity and fiberboard moisture levels within the package, and variations in moisture throughout the fiberboard assembly. This effort has examined packages with cane fiberboard and internal heat levels of 5 and 10W to date. Additional testing is expected to include 15 and 19W heat levels, and then repeat the same four heat levels with softwood fiberboard assemblies. This report documents the data collected to date within these two efforts.« less

  14. Fiberboard Humidity Data for 9975 Shipping Packages

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    The 9975 surveillance program is identifying a technical basis to support extending the storage period of 9975 packages in KAC beyond the currently approved 15 years. A key element of this effort is developing a better understanding of degradation of the fiberboard assembly under storage conditions. This degradation is influenced greatly by the moisture content of the fiberboard, which is not well characterized on an individual package basis. Two efforts have been undertaken to better understand the levels and behavior of moisture within the fiberboard assemblies of the 9975 shipping package. In the first effort, an initial survey of humiditymore » and temperature in the upper air space of 26 packages stored in KAC was made. The data collected within this first effort help to illustrate how the upper air space humidity varies with the local ambient temperature and package heat load. In the second effort, direct measurements of two test packages are providing a correlation between humidity and fiberboard moisture levels within the package, and variations in moisture throughout the fiberboard assembly. This effort has examined packages with cane fiberboard and internal heat levels of 5 and 10W to date. Additional testing is expected to include 15 and 19W heat levels, and then repeat the same four heat levels with softwood fiberboard assemblies. This report documents the data collected to date within these two efforts« less

  15. Fiberboard humidity data for 9975 shipping packages

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    The 9975 surveillance program is identifying a technical basis to support extending the storage period of 9975 packages in KAC beyond the currently approved 15 years. A key element of this effort is developing a better understanding of degradation of the fiberboard assembly under storage conditions. This degradation is influenced greatly by the moisture content of the fiberboard, which is not well characterized on an individual package basis.Two efforts have been undertaken to better understand the levels and behavior of moisture within the fiberboard assemblies of the 9975 shipping package. In the first effort, an initial survey of humidity andmore » temperature in the upper air space of 26 packages stored in KAC was made. The data collected within this first effort help to illustrate how the upper air space humidity varies with the local ambient temperature and package heat load. In the second effort, direct measurements of two test packages are providing a correlation between humidity and fiberboard moisture levels within the package, and variations in moisture throughout the fiberboard assembly. This effort has examined packages with cane fiberboard and internal heat levels of 5 and 10W to date. Additional testing is expected to include 15 and 19W heat levels, and then repeat the same four heat levels with softwood fiberboard assemblies. This report documents the data collected to date within these two efforts.« less

  16. Destructive examination of shipping package 9975-02101

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Destructive and non-destructive examinations have been performed on the components of shipping package 9975-02101 as part of the comprehensive Model 9975 package surveillance program. This package is one of ten high-wattage packages that were selected for field surveillance in FY15, and was identified to contain several non-conforming conditions. Most of these conditions (mold, stains, drum corrosion, calculated fiberboard dimensions and fiberboard damage) relate to the accumulation of water in the outer and lower portions of the cane fiberboard assembly. In the short term, this causes local but reversible changes in the fiberboard properties. Long-term effects can include the permanent lossmore » of fiberboard properties (thus far observed only in the bottom fiberboard layers) and reduced drum integrity due to corrosion. The observed conditions must be fully evaluated by KAC to ensure the safety function of the package is being maintained. Three of the other nine FY15 high-wattage packages examined in the K-Area Complex showed similar behavior. Corrosion of the overpack drum has been seen primarily in those packages with relatively severe fiberboard degradation. Visual examination of the drums in storage for external corrosion should be considered as a screening tool to identify additional packages with potential fiberboard degradation. Where overpack drum corrosion has been observed, it is typically heaviest adjacent to the stitch welds along the bottom edge. It is possible that changes to the stitch weld design would reduce the degree of corrosion in this area, but would not eliminate it. Several factors can contribute to the concentration of moisture in the fiberboard, including higher than average initial moisture content, higher internal temperature (due to internal heat load and placement with the array of packages), and the creation of additional moisture as the fiberboard begins to degrade.« less

  17. Model 9975 Life Extension Test Package 3 - Interim Report - January 2017

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    2017-01-31

    Life extension package LE3 (9975-03203) has been instrumented and subjected to an elevated temperature environment for approximately 8 years. During this time, the cane fiberboard has been maintained at a maximum temperature of ~160 - 165 °F, which was established by a combination of internal (19 watts) and external heat sources. Several tests and parameters were used to characterize the package components. Results from these tests generally indicate agreement between this full-scale shipping package and small-scale laboratory tests on fiberboard samples, including the degradation models based on the laboratory tests. These areas of agreement include the rate of change ofmore » fiberboard weight, dimensions and density, and change in fiberboard thermal conductivity. Corrosion of the lead shield occurred at a high rate during the first several weeks of aging, but dropped significantly after most of the moisture in the fiberboard migrated away from the lead shield. Dimensional measurements of the lead shield indicate that no significant creep deformation has occurred. This is consistent with literature data that predict a very small creep deformation for the time at temperature experienced by this package. The SCV O-rings were verified to remain leak-tight after ~5 years aging at an average temperature of ~170 °F. This package provides an example of the extent to which moisture within a typical fiberboard assembly can redistribute in the presence of a temperature gradient such as might be created by a 19 watt internal heat load. The majority of water within the fiberboard migrated to the bottom layers of fiberboard, with approximately 2 kg of water (2 liters) eventually escaping from the package. Two conditions have developed that are not consistent with package certification requirements. The axial gap at the top of the package increased to a maximum value of 1.549 inches, exceeding the 1 inch criterion. In addition, staining and/or corrosion have formed in a few spots on the drum. However, the package remains capable of performing its function. Aging of this package continues.« less

  18. Integrated Study of the Potential Application of Remediated CCA Treated Spruce Wood in MDF Production

    Treesearch

    Ronald Sabo; Altaf H. Basta; Jerrold E. Winandy

    2013-01-01

    Public health awareness has increased in the past few years regarding the disposal of chromated copper arsenate (CCA) preservative-treated wood wastes. This study demonstrates the potential for using remediated CCA lumber and alternative fiber sources, such as sugar cane bagasse, to produce medium density fiberboard (MDF). The role of both remediated CCA loaded spruce...

  19. Utilization of bagasse and coconut fibers waste as fillers of sandwich composite for bridge railway sleepers

    NASA Astrophysics Data System (ADS)

    Soehardjo, K. A.; Basuki, A.

    2017-07-01

    The bridge railway sleepers is an essential component in the construction of railways, as the foundation of the rail support in order to withstand the load a train that runs above it. Sleepers used in bridge construction are expected to have a longer service life, lighter weight and durable so that can be used more efficient. This research was carried out to create a model of bridges railway sleepers made of sandwich structured composite from fiber glass, epoxy resin with fillers waste of bagasse (sugar cane pulp mill) or coconut fiberboard (copra industry) that using polyurethane as an adhesive. The process of making was conditioned for small and medium industrial applications. Railway sleepers’ specifications adapted to meet the requirements of end user. The process steps in this research include; lay-up fiberglass combined with bagasse/coconut fiberboard (as fillers), gluing with epoxy resin, molded it with pressure to be solid, curing after solidification process. The specimens of composite, bagasse and coconut fiber board were tested for tensile and compressive strength. The prototype were tested of mechanical test: flexural moment test to the stand rail, flexural moment test to the middle of the sleepers and tensile strength test on one side of the sleepers, in accordance to SNI 11-3388-1994 Method testing of single block concrete sleepers and bearing single rail fastening systems. The results of mechanical testing all variations meet the technical specifications of end user such as test results for flexural moment on all prototypes, after load test, there is no visible crack. While in the tensile strength test, it seem the prototype with coconut fiberboard filler, shows better performance than bagasse fiberboard filler, the decisions is just depended on techno economic and lifetime.

  20. Examination of SR101 shipping packages

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Four SR101 shipping packages were removed from service and provided for disassembly and examination of the internal fiberboard assemblies. These packages were 20 years old, and had experienced varying levels of degradation. Two of the packages were successfully disassembled and fiberboard samples were removed from these packages and tested. Mechanical and thermal property values are generally comparable to or higher than baseline values measured on fiberboard from 9975 packages, which differs primarily in the specified density range. While baseline data for the SR101 material is not available, this comparison with 9975 material suggests that the material properties of the SR101more » fiberboard have not significantly degraded.« less

  1. Study on basalt fiber parameters affecting fiber-reinforced mortar

    NASA Astrophysics Data System (ADS)

    Orlov, A. A.; Chernykh, T. N.; Sashina, A. V.; Bogusevich, D. V.

    2015-01-01

    This article considers the effect of different dosages and diameters of basalt fibers on tensile strength increase during bending of fiberboard-reinforced mortar samples. The optimal dosages of fiber, providing maximum strength in bending are revealed. The durability of basalt fiber in an environment of cement, by means of microscopic analysis of samples of fibers and fiberboard-reinforced mortar long-term tests is examined. The article also compares the behavior of basalt fiber in the cement stone environment to a glass one and reveals that the basalt fiber is not subject to destruction.

  2. 49 CFR 178.802 - Preparation of fiberboard IBCs for testing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS... IBCs and composite IBCs with fiberboard outer packagings must be conditioned for at least 24 hours in..., fiberboard IBCs or composite IBCs with fiberboard outer packagings may be at ambient conditions. [Amdt. 178...

  3. 49 CFR 178.516 - Standards for fiberboard boxes.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... bending qualities. Fiberboard must be cut, creased without cutting through any thickness of fiberboard, and slotted so as to permit assembly without cracking, surface breaks, or undue bending. The fluting...

  4. Response of corrugated fiberboard to moisture flow : a 3-D finite element transient nonlinear analysis

    Treesearch

    Adeeb A. Rahman; Thomas J. Urbanik; Mustafa Mahamid

    2003-01-01

    Collapse of fiberboard packaging boxes, in the shipping industry, due to rise in humidity conditions is common and very costly. A 3D FE nonlinear model is developed to predict the moisture flow throughout a corrugated packaging fiberboard sandwich structure. The model predicts how the moisture diffusion will permeate through the layers of a fiberboard (medium and...

  5. FE analysis of creep and hygroexpansion response of a corrugated fiberboard to a moisture flow : a transient nonlinear analysis

    Treesearch

    Adeeb A. Rahman; Thomas J. Urbanik; Mustafa Mahamid

    2006-01-01

    This paper presents a model using finite element method to study the response of a typical commercial corrugated fiberboard due to an induced moisture function at one side of the fiberboard. The model predicts how the moisture diffusion will permeate through the fiberboard’s layers(medium and liners) providing information on moisture content at any given point...

  6. Mechanical properties of wood-based composite materials

    Treesearch

    Zhiyong Cai; Robert J. Ross

    2010-01-01

    The term composite is used to describe any wood material bonded together with adhesives. The current product mix ranges from fiberboard to laminated beams and components. In this chapter, wood-based composite materials are classified into the following categories: panel products (plywood, oriented strandboard (OSB), particleboard, fiberboard, medium-density fiberboard...

  7. Modification of wood fiber using steam

    Treesearch

    Roger Rowell; Sandra Lange; Jim McSweeny; Mark Davis

    2002-01-01

    High temperature steam treatment of wood fiber in a closed press during fiberboard pressing and then cooling the fiberboard while still under pressure to below the glass transition temperature of lignin, greatly increased the dimensional stability and decreased the hemicellulose content of the fiberboards produced. For example, after pressing aspen fiber four minutes...

  8. Effects of recycled fiber on the properties of fiberboard panels

    Treesearch

    Chin-yin Hwang; Chung-yun Hse; Todd F. Shupe

    2005-01-01

    This study examined the effects of recycled and virgin wood fiber on the properties of fiberboard. Replacing virgin fiber with recycled fiber adversely affected physical and mechanical properties of fiberboard. Bending properties and dimensional stability were linearly dependent on virgin fiber ratios. Based on strength properties, panels with 20 and 40 percent...

  9. Smoldering wave-front velocity in fiberboard

    Treesearch

    John J. Brenden; Erwin L. Schaffer

    1980-01-01

    In fiberboard, the phenomena of smoldering can be visualized as decomposition resulting from the motion of a thermal wave-front through the material. The tendency to smolder is then directly proportional to the velocity of the front. Velocity measurements were made on four fiberboards and were compared to values given in the literature for several substances....

  10. Ultrasound-Assisted Extraction of Stilbenes from Grape Canes.

    PubMed

    Piñeiro, Zulema; Marrufo-Curtido, Almudena; Serrano, Maria Jose; Palma, Miguel

    2016-06-16

    An analytical ultrasound-assisted extraction (UAE) method has been optimized and validated for the rapid extraction of stilbenes from grape canes. The influence of sample pre-treatment (oven or freeze-drying) and several extraction variables (solvent, sample-solvent ratio and extraction time between others) on the extraction process were analyzed. The new method allowed the main stilbenes in grape canes to be extracted in just 10 min, with an extraction temperature of 75 °C and 60% ethanol in water as the extraction solvent. Validation of the extraction method was based on analytical properties. The resulting RSDs (n = 5) for interday/intraday precision were less than 10%. Furthermore, the method was successfully applied in the analysis of 20 different grape cane samples. The result showed that grape cane byproducts are potentially sources of bioactive compounds of interest for pharmaceutical and food industries.

  11. Density profile and fiber alignment in fiberboard from three southern hardwoods

    Treesearch

    George E. Woodson

    1977-01-01

    Density profile and fiber orientation were evaluated for their effects on selected mechanical properties of medium density fiberboard. Bending MOE and modulus of rigidity were predicted from density profiles established by x-ray radiography. Orthotropic ratios ranged from 1.19 to 2.32 for electrically aligned fiberboards from three southern hardwoods. Off-axis tensile...

  12. Dynamic tension testing equipment for paperboard and corrugated fiberboard

    Treesearch

    W. D. Godshall

    1965-01-01

    The objective of this work was to develop a method, the testing equipment, and the instrumentation with which dynamic stress-strain information may be obtained for paperboards and built-up corrugated fiberboards as used in corrugated fiberboard containers. Much information is available on the properties of these materials when subjected to static or low rates of...

  13. Production of fiberboard using corn stalk pretreated with white-rot fungus Trametes hirsute by hot pressing without adhesive.

    PubMed

    Wu, Jianguo; Zhang, Xin; Wan, Jilin; Ma, Fuying; Tang, Yong; Zhang, Xiaoyu

    2011-12-01

    Corn stalk pretreated with white-rot fungus Trametes hirsute was used to produce fiberboard by hot pressing without adhesive. The moduli of rupture and elasticity of the corn-stalk-based fiberboard were increased 3.40- and 8.87-fold when bio-pretreated rather than untreated corn stalk was used. Fourier transform infra-red spectroscopy, X-ray diffraction, and chemical analysis showed that bio-pretreated corn stalk increased the mechanical properties of the fiberboard because it had more than twice the number of hydroxyl group, an 18% higher crystallinity, and twice the polysaccharide content of untreated corn stalk. Its laccase content was 4.65 ± 0.38 U/g. Corn stalk-based fiberboard production did not require adhesives, thus eliminating a potential source of toxic emissions such as formaldehyde gas. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Relationships among cane fitting, function, and falls.

    PubMed

    Dean, E; Ross, J

    1993-08-01

    Although canes are among the most commonly used mobility aids, little is known about the relationship between cane prescription and effectiveness. The purpose of this study was to examine the relationships among cane fitting (ie, cane fitter, cane band, and cane length), reported improvements in function, and reduction in falls. Cane users living in the community (86 women and 58 men with a median age distribution of 61 to 80 years) and sampled from seven urban shopping centers in British Columbia, Canada, participated in the study. The primary reasons cited for using a cane were joint problems (39%), general balance difficulties (30%), and a combination of joint and balance problems (15%). Measures included appropriateness of cane length and responses to closed-ended questions related to qualifications of the cane fitter, cane band, functional ability with a cane, and falling frequency. Overall, cane use was associated with improved confidence and functional ability. Canes fitted by health care workers approximated the clinically recommended length compared with canes fitted by non-health care workers, which tended to be greater than this length. There was no relationship, however, between cane fitting (cane fitter, cane hand, and appropriateness of cane length) and functional ability with a cane and falling frequency [corrected]. We concluded that health care workers may need to reconsider the variables for optimal cane prescription and their specifications for a given individual. The notion of a correct length and cane hand, for example, may be less important than factors such as the indications for cane use, comfort, and enhanced confidence.

  15. Moisture diffusion through a corrugated fiberboard under compressive loading : its deformation and stiffness response

    Treesearch

    Adeeb A. Rahman; Thomas J. Urbanik; Mustafa Mahamid

    2002-01-01

    This research develops a model using finite element to study the response of a panel made of a typical commercial corrugated fireboard due to an induced moisture function at one side of the fiberboard. The model predicts how the moisture diffusion will permeate through the fiberboard's layers (medium and liners) providing information on moisture content at any...

  16. Drop-Off Detection with the Long Cane: Effects of Different Cane Techniques on Performance

    ERIC Educational Resources Information Center

    Kim, Dae Shik; Emerson, Robert Wall; Curtis, Amy

    2009-01-01

    This study compared the drop-off detection performance with the two-point touch and constant contact cane techniques using a repeated-measures design with a convenience sample of 15 cane users with visual impairments. The constant contact technique was superior to the two-point touch technique in the drop-off detection rate and the 50% detection…

  17. Impact of Thermomechanical Fiber Pre-Treatment Using Twin-Screw Extrusion on the Production and Properties of Renewable Binderless Coriander Fiberboards.

    PubMed

    Uitterhaegen, Evelien; Labonne, Laurent; Merah, Othmane; Talou, Thierry; Ballas, Stéphane; Véronèse, Thierry; Evon, Philippe

    2017-07-17

    The aim of this study consisted of manufacturing renewable binderless fiberboards from coriander straw and a deoiled coriander press cake, thus at the same time ensuring the valorization of crop residues and process by-products. The press cake acted as a natural binder inside the boards owing to the thermoplastic behavior of its protein fraction during thermopressing. The influence of different fiber-refining methods was evaluated and it was shown that a twin-screw extrusion treatment effectively improved fiber morphology and resulted in fiberboards with enhanced performance as compared to a conventional grinding process. The best fiberboard was produced with extrusion-refined straw using a 0.4 liquid/solid (L/S) ratio and with 40% press cake addition. The water sensitivity of the boards was effectively reduced by 63% through the addition of an extrusion raw material premixing operation and thermal treatment of the panels at 200 °C, resulting in materials with good performance showing a flexural strength of 29 MPa and a thickness swelling of 24%. Produced without the use of any chemical adhesives, these fiberboards could thus present viable, sustainable alternatives for current commercial wood-based materials such as oriented strand board, particleboard and medium-density fiberboard, with high cost-effectiveness.

  18. Impact of Thermomechanical Fiber Pre-Treatment Using Twin-Screw Extrusion on the Production and Properties of Renewable Binderless Coriander Fiberboards

    PubMed Central

    Uitterhaegen, Evelien; Labonne, Laurent; Merah, Othmane; Talou, Thierry; Ballas, Stéphane; Véronèse, Thierry

    2017-01-01

    The aim of this study consisted of manufacturing renewable binderless fiberboards from coriander straw and a deoiled coriander press cake, thus at the same time ensuring the valorization of crop residues and process by-products. The press cake acted as a natural binder inside the boards owing to the thermoplastic behavior of its protein fraction during thermopressing. The influence of different fiber-refining methods was evaluated and it was shown that a twin-screw extrusion treatment effectively improved fiber morphology and resulted in fiberboards with enhanced performance as compared to a conventional grinding process. The best fiberboard was produced with extrusion-refined straw using a 0.4 liquid/solid (L/S) ratio and with 40% press cake addition. The water sensitivity of the boards was effectively reduced by 63% through the addition of an extrusion raw material premixing operation and thermal treatment of the panels at 200 °C, resulting in materials with good performance showing a flexural strength of 29 MPa and a thickness swelling of 24%. Produced without the use of any chemical adhesives, these fiberboards could thus present viable, sustainable alternatives for current commercial wood-based materials such as oriented strand board, particleboard and medium-density fiberboard, with high cost-effectiveness. PMID:28714928

  19. Factors associated with cane use among community dwelling older adults.

    PubMed

    Aminzadeh, F; Edwards, N

    2000-01-01

    Guided by the Theory of Planned Behavior (TPB), this study examined factors associated with cane use among community dwelling older adults. Data were collected in a cross-sectional survey of a convenience sample of 106 community residing older adults in Ottawa, Canada. Using a stepwise discriminant analysis, subjective norms, attitudes, and age surfaced as the key variables associated with cane use in this sample. The discriminant function accounted for 67% of the variance in cane use and correctly classified 91% of cases (Wilks's lambda = 0.33, lambda2 = 110.12, df = 3, p < 0.0001). The findings provide evidence for the utility of the TPB in its application to understanding cane use behaviors of older persons and have important implications for the design of theory-based fall prevention interventions to enhance the acceptance and effective use of mobility aids.

  20. Chemometric characterization of alembic and industrial sugar cane spirits from cape verde and ceará, Brazil.

    PubMed

    Pereira, Regina F R; Vidal, Carla B; de Lima, Ari C A; Melo, Diego Q; Dantas, Allan N S; Lopes, Gisele S; do Nascimento, Ronaldo F; Gomes, Clerton L; da Silva, Maria Nataniela

    2012-01-01

    Sugar cane spirits are some of the most popular alcoholic beverages consumed in Cape Verde. The sugar cane spirit industry in Cape Verde is based mainly on archaic practices that operate without supervision and without efficient control of the production process. The objective of this work was to evaluate samples of industrial and alembic sugar cane spirits from Cape Verde and Ceará, Brazil using principal component analysis. Thirty-two samples of spirits were analyzed, twenty from regions of the islands of Cape Verde and twelve from Ceará, Brazil. Of the samples obtained from Ceará, Brazil seven are alembic and five are industrial spirits. The components analyzed in these studies included the following: volatile organic compounds (n-propanol, isobutanol, isoamylic, higher alcohols, alcoholic grade, acetaldehyde, acetic acid, acetate); copper; and sulfates.

  1. Chemometric Characterization of Alembic and Industrial Sugar Cane Spirits from Cape Verde and Ceará, Brazil

    PubMed Central

    Pereira, Regina F. R.; Vidal, Carla B.; de Lima, Ari C. A.; Melo, Diego Q.; Dantas, Allan N. S.; Lopes, Gisele S.; do Nascimento, Ronaldo F.; Gomes, Clerton L.; da Silva, Maria Nataniela

    2012-01-01

    Sugar cane spirits are some of the most popular alcoholic beverages consumed in Cape Verde. The sugar cane spirit industry in Cape Verde is based mainly on archaic practices that operate without supervision and without efficient control of the production process. The objective of this work was to evaluate samples of industrial and alembic sugar cane spirits from Cape Verde and Ceará, Brazil using principal component analysis. Thirty-two samples of spirits were analyzed, twenty from regions of the islands of Cape Verde and twelve from Ceará, Brazil. Of the samples obtained from Ceará, Brazil seven are alembic and five are industrial spirits. The components analyzed in these studies included the following: volatile organic compounds (n-propanol, isobutanol, isoamylic, higher alcohols, alcoholic grade, acetaldehyde, acetic acid, acetate); copper; and sulfates. PMID:23227051

  2. Use of Advanced Spectroscopic Techniques for Predicting the Mechanical Properties of Wood Composites

    Treesearch

    Timothy G. Rials; Stephen S. Kelley; Chi-Leung So

    2002-01-01

    Near infrared (NIR) spectroscopy was used to characterize a set of medium-density fiberboard (MDF) samples. This spectroscopic technique, in combination with projection to latent structures (PLS) modeling, effectively predicted the mechanical strength of MDF samples with a wide range of physical properties. The stiffness, strength, and internal bond properties of the...

  3. Drop-off Detection with the Long Cane: Effects of Different Cane Techniques on Performance

    PubMed Central

    Kim, Dae Shik; Emerson, Robert Wall; Curtis, Amy

    2010-01-01

    This study compared the drop-off detection performance with the two-point touch and constant contact cane techniques using a repeated-measures design with a convenience sample of 15 cane users with visual impairments. The constant contact technique was superior to the two-point touch technique in the drop-off detection rate and the 50% detection threshold. The findings may help an orientation and mobility instructor select an appropriate technique for a particular client or training situation. PMID:21209791

  4. Stilbene levels in grape cane of different cultivars in southern Chile: determination by HPLC-DAD-MS/MS method.

    PubMed

    Vergara, Carola; von Baer, Dietrich; Mardones, Claudia; Wilkens, Andrea; Wernekinck, Katerina; Damm, Anika; Macke, Sebastian; Gorena, Tamara; Winterhalter, Peter

    2012-02-01

    Health benefits of trans-resveratrol and other stilbenes in grapes, must, and wine have been pointed out by numerous authors. Less attention has been paid to the presence of stilbene derivatives in viticultural residues, such as grape canes. The present work reports the first results of a systematic study of stilbene levels in different grape varieties and cultivation areas in Chile, to evaluate their potential as an alternative source of bioactive stilbenes. In all cane samples, the predominant stilbene is trans-resveratrol, followed by ε-viniferin and piceatannol. In canes of Pinot noir up to 5590 ± 172 mg kg(-1) of trans-resveratrol and up to 6915 ± 175 mg kg(-1) of total stilbenes were detected. The observed concentrations of stilbenes in canes of Pinot noir from southern Chile until now are higher than those reported previously for this red variety. However, the highest concentration of total stilbenes observed in the analyzed samples was in the canes of white variety Gewürztraminer with 7857 ± 498 mg kg(-1). Preliminary results indicate that these levels can evolve if canes are left for some months on the vineyard after pruning, observing an increase during the first 2 months and a decrease after this period.

  5. Examination of shipping packages 9975-01658, 9975-02075 and 9975-02738

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    SRNL has assisted in the examination of three 9975 shipping packages (9975-01658, 9975-02075 and 9975-02738) following their use for storage of nuclear material in K-Area Complex (KAC). Each of these was targeted for examination because the axial gap exceeded the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Each package experienced a degree of compaction of the bottom fiberboard layers, and had elevated moisture levels toward the bottom. A small amount of mold was observed on the lower fiberboard assembly in 9975-02738. However, the majority of the fiberboard in each package appeared tomore » retain good integrity consistent with non-degraded material. Minor corrosion was observed on these drums, but is judged to have not compromised the drum integrity.« less

  6. 7 CFR 2902.19 - Composite panels.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ...; and Signage. USDA is requesting that manufacturers of these qualifying biobased products provide... EPA-designated laminated paperboard, structural fiberboard, shower and restroom dividers, and signage... laminated paperboard and structural fiberboard, shower and restroom dividers, and signage containing...

  7. 7 CFR 2902.19 - Composite panels.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ...; and Signage. USDA is requesting that manufacturers of these qualifying biobased products provide... EPA-designated laminated paperboard, structural fiberboard, shower and restroom dividers, and signage... laminated paperboard and structural fiberboard, shower and restroom dividers, and signage containing...

  8. 49 CFR 178.603 - Drop test.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... drums, Plastic drums and Jerricans, Composite packagings which are in the shape of a drum Six—(three for... of natural wood, Plywood boxes, Reconstituted wood boxes, Fiberboard boxes, Plastic boxes, Steel or... Administrator. (c) Special preparation of test samples for the drop test. (1) Testing of plastic drums, plastic...

  9. Parent Physical Punishment and Child Aggression in a Singapore Chinese Preschool Sample

    ERIC Educational Resources Information Center

    Ngee Sim, Tick; Ping Ong, Lue

    2005-01-01

    We examine how parental physical punishment (caning and slapping) and child aggression are related, and possible moderation by authoritative control and rejection. A sample of 286 Singapore Chinese preschoolers ages 4-6 reported on rejection; their parents reported on control, caning, and slapping; and their teachers rated child aggression.…

  10. Soil water nitrate concentrations in giant cane and forest riparian buffer zones

    Treesearch

    Jon E. Schoonover; Karl W. J. Williard; James J. Zaczek; Jean C. Mangun; Andrew D. Carver

    2003-01-01

    Soil water nitrate concentrations in giant cane and forest riparian buffer zones along Cypress Creek in southern Illinois were compared to determine if the riparian zones were sources or sinks for nitrogen in the rooting zone. Suction lysimeters were used to collect soil water samples from the lower rooting zone in each of the two vegetation types. The cane riparian...

  11. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Destructive and non-destructive examinations have been performed on the components of shipping package 9975-02019 as part of a comprehensive SRS surveillance program for plutonium material stored in the K-Area Complex (KAC). During the field surveillance inspection of this package in KAC, two non-conforming conditions were noted: the axial gap of 1.577 inch exceeded the 1 inch maximum criterion, and two areas of dried glue residue were noted on the upper fiberboard subassembly. This package was subsequently transferred to SRNL for more detailed inspection and destructive examination. In addition to the conditions noted in KAC, the following conditions were noted: -more » Numerous small spots of corrosion were observed along the bottom edge of the drum. - In addition to the smeared glue residue on the upper fiberboard subassembly, there was also a small dark stain. - Mold was present on the side and bottom of the lower fiberboard subassembly. Dark stains from elevated moisture content were also present in these areas. - A dark spot with possible light corrosion was observed on the primary containment vessel flange, and corresponding rub marks were observed on the secondary containment vessel ID. - The fiberboard thermal conductivity in the radial orientation was above the specified range. When the test was repeated with slightly lower moisture content, the result was acceptable. The moisture content for both tests was within a range typical of other packages in storage. The observed conditions must be fully evaluated by KAC to ensure the safety function of the package is being maintained. Several factors can contribute to the concentration of moisture in the fiberboard, including higher than average initial moisture content, higher internal temperature (due to internal heat load and placement within the array of packages), and the creation of additional moisture as the fiberboard begins to degrade.« less

  12. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... be constructed of multiple plies of heavy paper or fiberboard (without corrugations) firmly glued or laminated together and may include one or more protective layers of bitumen, waxed kraft paper, metal foil, plastic material, or similar materials. (2) Heads must be of natural wood, fiberboard, metal, plywood...

  13. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... be constructed of multiple plies of heavy paper or fiberboard (without corrugations) firmly glued or laminated together and may include one or more protective layers of bitumen, waxed kraft paper, metal foil, plastic material, or similar materials. (2) Heads must be of natural wood, fiberboard, metal, plywood...

  14. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... be constructed of multiple plies of heavy paper or fiberboard (without corrugations) firmly glued or laminated together and may include one or more protective layers of bitumen, waxed kraft paper, metal foil, plastic material, or similar materials. (2) Heads must be of natural wood, fiberboard, metal, plywood...

  15. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... be constructed of multiple plies of heavy paper or fiberboard (without corrugations) firmly glued or laminated together and may include one or more protective layers of bitumen, waxed kraft paper, metal foil, plastic material, or similar materials. (2) Heads must be of natural wood, fiberboard, metal, plywood...

  16. JPRS Report, East Europe

    DTIC Science & Technology

    1990-05-09

    agree- The fiberboard factory in Karlin has incredibly upped its ment with a Swedish company, IKEA , for leasing from prices, so we told them "thanks but...other furniture factories and the IKEA off. company, building a fiberboard plant in Czarnkow and [ZYCIE WARSZAWY] What has been this year like, so

  17. Viral discovery in the invasive Australian cane toad (Rhinella marina) using metatranscriptomic and genomic approaches.

    PubMed

    Russo, Alice G; Eden, John-Sebastian; Enosi Tuipulotu, Daniel; Shi, Mang; Selechnik, Daniel; Shine, Richard; Rollins, Lee Ann; Holmes, Edward C; White, Peter A

    2018-06-13

    Cane toads are a notorious invasive species, inhabiting over 1.2 million km 2 of Australia and threatening native biodiversity. Release of pathogenic cane toad viruses is one possible biocontrol strategy yet is currently hindered by the poorly-described cane toad virome. Metatranscriptomic analysis of 16 cane toad livers revealed the presence of a novel and full-length picornavirus, Rhimavirus A (RhiV-A), a member of a reptile and amphibian specific-cluster of the Picornaviridae basal to the Kobuvirus -like group. In the combined liver transcriptome, we also identified a complete genome sequence of a distinct epsilonretrovirus, R. marina endogenous retrovirus (RMERV). The recently sequenced cane toad genome contains eight complete RMERV proviruses, as well as 21 additional truncated insertions. The oldest full length RMERV provirus was estimated to have inserted 1.9 MYA. To screen for these viral sequences in additional toads, we analysed publicly available transcriptomes from six diverse Australian locations. RhiV-A transcripts were identified in toads sampled from three locations across 1,000 km of Australia, stretching to the current Western Australia (WA) invasion front, whilst RMERV transcripts were observed at all six sites. Lastly, we scanned the cane toad genome for non-retroviral endogenous viral elements, finding three sequences related to small DNA viruses in the family Circoviridae This shows ancestral circoviral infection with subsequent genomic integration. The identification of these current and past viral infections enriches our knowledge of the cane toad virome, an understanding of which will facilitate future work on infection and disease in this important invasive species. Importance Cane toads are poisonous amphibians which were introduced to Australia in 1935 for insect control. Since then, their population has increased dramatically, and they now threat many native Australian species. One potential method to control the population is to release a cane toad virus with high mortality, yet few cane toad viruses have been characterised. This study samples cane toads from different Australian locations and uses an RNA sequencing and computational approach to find new viruses. We report novel complete picornavirus and retrovirus sequences which were genetically similar to viruses infecting frogs, reptiles and fish. Using data generated in other studies, we show that these viral sequences are present in cane toads from distinct Australian locations. Three sequences related to circoviruses were also found in the toad genome. The identification of new viral sequences will aid future studies which investigate their prevalence and potential as agents for biocontrol. Copyright © 2018 American Society for Microbiology.

  18. Which type of cane is the most efficient, based on oxygen consumption and balance capacity, in chronic stroke patients?

    PubMed

    Jeong, Yeon-Gyu; Jeong, Yeon-Jae; Myong, Jun-Pyo; Koo, Jung-Wan

    2015-02-01

    Canes are widely prescribed as walking aids, but little is known about the effects of canes on the physiological cost of walking. The purpose of this study was to investigate the differences in oxygen consumption associated with the gaits of hemiplegic patients in terms of balance capacity according to the type of cane used. Twenty-nine patients with chronic stroke were divided into poor-balance (n=15) and relatively-better-balance groups (n=14) based on a cutoff score of 49 on the Berg balance scale (BBS). Each patient completed three consecutive days of walking with a randomly assigned singlepoint cane, quad cane, or hemi-walker. We measured the oxygen expenditure and oxygen cost using a portable gas analyzer and heart rate during a 6-min walk test (6MWT) and a 10-m walk test (10MWT). The oxygen expenditure, gait endurance, and gait velocity were higher with the single-point cane (p<0.01) than with any of the other cane types, and the oxygen costs were lower (p<0.01) with the single-point cane among the patients with relatively better balance. The oxygen cost for the quad cane was lower (p<0.01) than that found for any the other cane types among the patients with relatively poor balance. Our study revealed that single-point canes require less oxygen use at a given speed and permits greater speed at the same oxygen consumption for hemiplegic patients with good balance. Walking aids with a greater base support may be more suitable than those with a smaller base support for patients with relatively poor balance. However, our conclusions are only preliminary because of the small sample size (KCT0001076). Copyright © 2014 Elsevier B.V. All rights reserved.

  19. 49 CFR 178.708 - Standards for fiberboard IBCs.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...) Construction requirements for fiberboard IBCs are as follows: (1) Top lifting devices are prohibited in... foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171.7 of this subchapter). (ii.... Where a detachable pallet is used, its top surface must be free from sharp protrusions that might damage...

  20. 49 CFR 178.708 - Standards for fiberboard IBCs.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...) Construction requirements for fiberboard IBCs are as follows: (1) Top lifting devices are prohibited in... foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171.7 of this subchapter). (ii.... Where a detachable pallet is used, its top surface must be free from sharp protrusions that might damage...

  1. 49 CFR 178.708 - Standards for fiberboard IBCs.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) Construction requirements for fiberboard IBCs are as follows: (1) Top lifting devices are prohibited in... foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171.7 of this subchapter). (ii.... Where a detachable pallet is used, its top surface must be free from sharp protrusions that might damage...

  2. 49 CFR 178.708 - Standards for fiberboard IBCs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...) Construction requirements for fiberboard IBCs are as follows: (1) Top lifting devices are prohibited in... foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171.7 of this subchapter). (ii.... Where a detachable pallet is used, its top surface must be free from sharp protrusions that might damage...

  3. Technique for in-place welding of aluminum backed up by a combustible material

    NASA Technical Reports Server (NTRS)

    Spagnuolo, A. C.

    1971-01-01

    Welding external aluminum jacket, tightly wrapped around inner layer of wood composition fiberboard, in oxygen free environment prevents combustion and subsequent damage to underlying fiberboard. Technique also applies to metal cutting in similar assemblies without disassembly to remove combustible materials from welding heat proximity.

  4. Estimation of the sugar cane cultivated area from LANDSAT images using the two phase sampling method

    NASA Technical Reports Server (NTRS)

    Parada, N. D. J. (Principal Investigator); Cappelletti, C. A.; Mendonca, F. J.; Lee, D. C. L.; Shimabukuro, Y. E.

    1982-01-01

    A two phase sampling method and the optimal sampling segment dimensions for the estimation of sugar cane cultivated area were developed. This technique employs visual interpretations of LANDSAT images and panchromatic aerial photographs considered as the ground truth. The estimates, as a mean value of 100 simulated samples, represent 99.3% of the true value with a CV of approximately 1%; the relative efficiency of the two phase design was 157% when compared with a one phase aerial photographs sample.

  5. Bamboo fiberboards and attapulgite : does it lead to an improvement of humidity control in buildings?

    NASA Astrophysics Data System (ADS)

    Nguyen, D. M.; Grillet, A. C.; Goldin, T.; Hanh Diep, T. M.; Woloszyn, M.

    2018-04-01

    In order to save energy used to heat or cool buildings and to improve the inhabitants comfort, control of humidity inside buildings must be improved. This can be done by using buffering materials able to absorb and release moisture when necessary. Natural fibers and mineral absorbent are good candidates to manufacture such materials. The aim of this research is to mix bamboo fibers with attapulgite to evaluate the influence of this mineral absorbent on the hygric behavior of the fiberboards. The hygric properties are slightly improved by the attapulgite and thus bamboo fiberboards can be used as building insulation materials able to participate to the indoor moisture control.

  6. Energy Expenditure During Cane-Assisted Gait in Patients with Knee Osteoarthritis

    PubMed Central

    Jones, Anamaria; Alves, Ana Claudia Monteiro; de Oliveira, Leda Magalhães; Saad, Marcelo; Natour, Jamil

    2008-01-01

    OBJECTIVE To compare the energy expenditure in patients with unilateral knee osteoarthritis while walking with canes of different lengths. METHODS A quasi-experimental study (single-group) was carried out on thirty patients with unilateral knee osteoarthritis. An adjustable aluminum cane was used, and three different cane lengths were determined for each subject: C1 – length from the floor to the greater trochanter; C2 – length from the floor to the distal wrist crease; and C3 – length obtained by the formula: height x 0.45 + 0.87 m. Resting and walking heart rates were measured with a Polar hear rate meter. Walking speed was calculated by the time required for the patient to walk 10 m. Gait energy cost was estimated using the physiological cost index, and results were compared. RESULTS The sample consisted of 25 women and five men (average age of 68 years). Statistically significant differences in physiological cost index measurements were observed between unassisted walking and assisted walking with a cane of any length (p<0.001), as well as between walking with a C2-length cane and unassisted walking, and walking with a C1-length cane and walking with a C3-length cane (p=0.001; p = 0.037; p=0.001; respectively). CONCLUSION These data demonstrate that small alterations in the length of canes used for weight-bearing ambulation in patients with unilateral knee osteoarthritis increase the energy expenditure measured by the physiological cost index during walking. Further studies are needed for a more precise quantification of the increase in energy expenditure during cane-assisted gait and an assessment of the effectiveness of cane use in relieving pain and improving function in patients with knee osteoarthritis. PMID:18438573

  7. Monitoring Freeze Injury and Evaluating Losingto Sugar-Cane Using RS and GPS

    NASA Astrophysics Data System (ADS)

    Tan, Zongkun; Ding, Meihua; Wang, Longhe; Yang, Xin; Ou, Zhaorong

    From Jan 12th to Feb 12th 2008, the most severity cold chilling and freeze injury weather took place during the last 50 years in the southern of China.Sugar-cane was suffered injury severity. However, the losing of sugar-cane which it was aroused by thisweather disaster had not been exactitude evaluated till on Apr 1st, 2008. It was not only affected the sugar-cane ordinary harvesting and crushing, but also affected reserving sugar-cane seed for planting. Freeze injury is common disaster for sugar-cane in southern of China and monitoring freeze injury using RS and GIS are of great economic significance but little research work about it has been done in China Freeze injuring is not only related to crop growth stage and the cold air intension from northern to southern and weather types, but also consanguineous related to land form and physiognomy and geographical latitude and height above sea level etc and crop planting spatial distribution. The case study of Guangxi province which is the biggest region of sugar-cane planting in China in this paper, the values of sugar-cane NDVI among the freeze injury occur former and after in early 2008 and without freeze injury occur in the same term 2007 were analyzed and compared based on the sugar-cane planting spatial distribution information which were carried out by using multi-phase EOS/MODIS data. The result showed that it was not only commendably reflected the spatial distribution of freeze injury but also reflected the sugarcane suffered from degree using the values of sugar-cane NDVIof freeze injury occur former and after. The field sample investigation data of using GPS was integrated with the NDVI, the evaluation of region sugar-cane suffer from freeze injury losing could quickly and exactly realize.

  8. 49 CFR 178.708 - Standards for fiberboard IBCs.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... part of it. (c) Construction requirements for fiberboard IBCs are as follows: (1) Top lifting devices... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... stability in handling and transport. Where a detachable pallet is used, its top surface must be free from...

  9. Properties of medium-density fiberboard produced in an oil-heated laboratory press

    Treesearch

    O. Suchsland; G.E. Woodson

    1976-01-01

    Medium-density fiberboards from pressurized double-disk refined fibers have a close correlation between layer density and layer dynamic modulus of elasticity. Density distribution over the thickness was readily controlled by manipulating platen temperature and applied pressure. Thus, overall modulus of elasticity could be adjusted. In contrast to modulus of elasticity...

  10. Optimum fiber distribution in singlewall corrugated fiberboard

    Treesearch

    Millard W. Johnson; Thomas J. Urbanik; William E. Denniston

    1979-01-01

    Determining optimum distribution of fiber through rational design of corrugated fiberboard could result in significant reductions in fiber required to meet end-use conditions, with subsequent reductions in price pressure and extension of the softwood timber supply. A theory of thin plates under large deformations is developed that is both kinematically and physically...

  11. Properties of bio-based medium density fiberboard

    Treesearch

    Sangyeob Lee; Todd F. Shupe; Chung Y. Hse

    2006-01-01

    In order to utilize agricultural waste fibers as an alternative resource for composites, a number of variables were investigated to determine whether the mechanical and physical properties of agro-based fiberboard could be improved. Fibers were classified into four different mesh sizes and used to evaluated the effect of fiber size on the mechanical and physical...

  12. Utilization of Chinese tallow tree and bagasse for medium density fiberboard

    Treesearch

    Sangyeob Lee; Todd F. Shupe; Chung Y. Hse

    2004-01-01

    The objective of this research was to investigate various adhesive systems and determine the best composite formulation for selected mechanical and physical properties of medium density fiberboard (MDF) made from wood and bagasse fibers. This study investigated opportunities ofbiomass utilization for natural fiber-based composites from agricultural (bagasse) and...

  13. Mechanical and physical properties of agro-based fiberboard

    Treesearch

    S. Lee; T.F. Shupe; C.Y. Hse

    2006-01-01

    In order to better utilize agricultural fibers as an alternative resource for composite panels, several variables were investigated to improve mechanical and physical properties of agm-based fiberboard. This study focused on the effect of fiber morphology, slenderness ratios (UD), and fiber mixing combinations on panel properties. The panel construction types were also...

  14. Galactoglucomannan Oligosaccharides (GGMO) from a Molasses Byproduct of Pine (Pinus taeda) Fiberboard Production

    USDA-ARS?s Scientific Manuscript database

    “Temulose” is the trade name for a water-soluble molasses produced on a large scale (300 - 400 tonnes per year) as a byproduct of the fiberboard industry. The feedstock for temulose is predominantly a single species of pine (Pinus taeda) grown and harvested in stands in southeastern Texas. Because...

  15. Aldehyde emissions from particleboard and medium density fiberboard products

    Treesearch

    Melissa G. D. Baumann; Linda F. Lorenz; Stuart A. Batterman; Guo-Zheng Zhang

    2000-01-01

    Indoor air quality problems resulting from the emission of volatile organic compounds (VOCs) have become an issue of increasing concern. Emissions from building and furnishing materials, which are frequently constructed from particleboard and medium density fiberboard (MDF), are a potentially important contributor of indoor VOCs. In this research, VOC emissions from...

  16. Fire performance of fiber board coated with nano kaolin-clay film

    Treesearch

    Zhijia Liu; John F. Hunt; Zhiyong Cai

    2013-01-01

    Fiberboard is a common interior material used both in China and the United States of America. The increase in demand for interior materials has raised concerns regarding combustibility of the materials. The pyrolysis characteristics of fiber, phenolic resin (PF), and nano kaolin-clay (NK) were investigated using thermogravimetry. The fire performances of samples coated...

  17. Assessing met and unmet needs in the oldest-old and psychometric properties of the German version of the Camberwell assessment of need for the elderly (CANE)--a pilot study.

    PubMed

    Stein, Janine; Luppa, Melanie; König, Hans-Helmut; Riedel-Heller, Steffi G

    2014-02-01

    The current demographic and social developments in our society will lead to a significant increase in treatment and healthcare needs in the future, particularly in the elderly population. The Camberwell Assessment of Need for the Elderly (CANE) was developed in the United Kingdom to measure physical-, psychological-, and environment-related treatment as well as healthcare needs of older people in order to identify their unmet needs. So far, the German version of the CANE has not been established in health services research. Major reasons for this are a lack of publications of CANE's German version and the missing validation of the instrument. The aims of the present study were to evaluate the currently available German version of the CANE in a sample of older primary care patients. Descriptive statistics and inference-statistical analyses were calculated. Patients reported unmet needs mostly in CANE's following sections: mobility/falls, physical health, continence, company, and intimate relationships. Agreement level between patients' and relatives' ratings in CANE was moderate to low. Evidence for the construct validity of CANE was found in terms of significant associations between CANE and other instruments or scores. The study results provide an important basis for studies aiming at the assessment of met and unmet needs in the elderly population. Using the German version of the CANE may substantially contribute to an effective and good-quality health and social care as well as an appropriate allocation of healthcare resources in the elderly population.

  18. A detachable electronic device for use with a long white cane to assist with mobility.

    PubMed

    O'Brien, Emily E; Mohtar, Aaron A; Diment, Laura E; Reynolds, Karen J

    2014-01-01

    Vision-impaired individuals often use a long white cane to assist them with gathering information about their surroundings. However, these aids are generally not used to detect obstacles above knee height. The purpose of this study is to determine whether a low-cost, custom-built electronic device clipped onto a traditional cane can provide adequate vibratory warning to the user of obstacles above knee height. Sixteen normally sighted blindfolded individuals participated in two mobility courses which they navigated using a normal white cane and a white cane with the electronic device attached. Of the 16 participants, 10 hit fewer obstacles, and 12 covered less ground with the cane when the electronic device was attached. Ten participants found navigating with the electronic device easier than just the white cane alone. However, the time taken on the mobility courses, the number of collisions with obstacles, and the area covered by participants using the electronic device were not significantly different (p > 0.05). A larger sample size is required to determine if the trends found have real significance. It is anticipated that additional information provided by this electronic device about the surroundings would allow users to move more confidently within their environment.

  19. Diet composition of the invasive cane toad (Chaunus marinus) on Rota, Northern Mariana Islands

    USGS Publications Warehouse

    Reed, R.N.; Bakkegard, K.A.; Desy, G.E.; Plentovich, S.M.

    2007-01-01

    The cane or marine toad (Chaunus marinus, formerly Bufo marinus) was introduced to the Northern Mariana Islands starting in the 1930s. The effects of this exotic predator on native vertebrates (especially lizards) are largely unknown. We analysed the stomach contents of 336 cane toads collected from the island of Rota, with the goal of estimating the level of toad predation on native vertebrates. Beetles, ants, millipedes, and grasshoppers/crickets comprised the majority of prey classes consumed by toads. The introduced Brahminy blindsnake (Ramphotyphlops braminus; N = 6) and conspecific cane toads (N = 4) were the vertebrates most commonly found in toad stomachs. Skinks (Emoia; N = 2) were the only native vertebrates represented in our sample. The small numbers of nocturnal terrestrial vertebrates native to Rota likely translates to relatively low rates of predation by cane toads on native vertebrates.

  20. Adhesive in the buckling failure of corrugated fiberboard : a finite element investigation

    Treesearch

    Adeeb A. Rahman; Said M. Abubakr

    1998-01-01

    This research study proposed to include the glue material in a finite element model that represents the actual geometry and material properties of a corrugated fiberboard. The model is a detailed representation of the different components of the structure (adhesive, linerboard, medium) to perform buckling analysis of corrugated structures under compressive loads. The...

  1. Effects of panel density and mat moisture content on processing medium density fiberboard

    Treesearch

    Zhiyong Cai; James H. Muehl; Jerrold E. Winandy

    2006-01-01

    Development of a fundamental understanding of heat transfer and resin curing during hot- pressing will help to optimize the manufacturing process of medium density fiberboard (MDF) allowing increased productivity, improved product quality, and enhanced durability. Effect of mat moisture content (MC) and panel density on performance of MDF panels, heat transfer,...

  2. On the measurement of fiber orientation in fiberboard

    Treesearch

    Otto Suchsland; Charles W. McMillin

    1983-01-01

    An attempt to measure the vertical component of fiber orientation in fiberboard is described. The experiment is based on the obvious reduction of the furnish fiber length which occurs by cutting thin microtome sections of the board parallel to the board plane. Only when no vertical fiber orientation component is present will the fibers contained in these sections have...

  3. Lightweight and Compostable Fiberboard for the Military

    DTIC Science & Technology

    2012-08-01

    individual sheets with compression molding methods. The second approach examined different biodegradable coatings for paper formation which enhanced wet...strength properties of paper based products. The third approach identified effective coated corrugated alternatives that exhibited comparable...fiberboard containers to different environmental conditions. Analysis of variance of compression data as a function of moisture, insert design and paper

  4. Decay and termite resistance of medium density fiberboard (MDF) made from different wood species

    Treesearch

    S. Nami Kartal; Frederick Green

    2003-01-01

    Medium density fiberboard (MDF) production worldwide is increasing due to the development of new manufacturing technologies. As a result, MDF products are increasingly utilized in traditional wood applications that require fungal and insect resistance. This study evaluated the ability of white and brown rot fungi and termites to decompose MDF consisting of different...

  5. Medium density fiberboard from mixed southern hardwoods

    Treesearch

    George E. Woodson

    1977-01-01

    Medium-density fiberboards of acceptable quality were made from a mixture of barky chips from 14 southern hardwoods. Boards made from fiber refined at three different plate clearances did not vary significantly in bending, internal bond (IB), or linear expansion. but, lack of replications and the fact that the refiner was not loaded to capacity caused these results to...

  6. Dry chips versus green chips as furnish for medium-density fiberboard

    Treesearch

    Paul H. Short; George E. Woodson; Duane E. Lyon

    1978-01-01

    The fiber characteristics and the physical and mechanical properties of medium-density fiberboard (MDF), manufactured with pressure-refined fiber from green and partially dried raw material, were analyzed to determine if dry wood chips made a better furnish than green wood chips. Pressure-refining dry material produced coarser fiber than those obtained from green...

  7. Dry chips versus green chips as furnish for medium-density fiberboard

    Treesearch

    P.H. Short; G.E. Woodson; D.E. Lyon

    1978-01-01

    The fiber characteristics and the physical and mechanical properties of medium-density fiberboard (MDF), manufactured with pressure-refined fiber from green and partially dried raw material, were analyzed to determine if dry wood chips made a better furnish than green wood chips. Pressure-refined dry material produced coarser fiber than those obtained from green...

  8. High-frequency and hot-platen curing of medium-density fiberboards

    Treesearch

    Robert R. Stevens; George E. Woodson

    1977-01-01

    The effects of two curing methods-high-frequencey heating and hot-platen heating-on the properties of a ureaformaldehyde-bonded medium-density fiberboard prepared with a southern-hardwoods furnish (50% southern read oak, 25% mockernut hickory, and 25% sweetgum) were studied. Boards of three densities-38, 44, and 50 lb./ft3-were cured by the two...

  9. Effects of post heat-treatment on surface characteristics and adhesive bonding performance of medium density fiberboard

    Treesearch

    Nadir Ayrilimis; Jerrold E. Winandy

    2009-01-01

    A series of commercially manufactured medium density fiberboard (MDF) panels were exposed to a post-manufacture heat-treatment at various temperatures and durations using a hot press and just enough pressure to ensure firm contact between the panel and the press platens. Post-manufacture heat-treatment improved surface roughness of the exterior MDF panels. Panels...

  10. Development of a bending stiffness model for wet process fiberboard

    Treesearch

    Chris Turk; John F. Hunt

    2007-01-01

    In traditional mechanics of materials, the stiffness of a beam or plate in bending is described by its cross-sectional shape as well as its material properties, primarily the modulus of elasticity. Previous work at the USDA Forest Products Laboratory, Madison, Wisconsin, has shown that modulus of elasticity has a strong correlation to the density of the fiberboard....

  11. Effect of silvicultural practice and wood type on loblolly pine particleboard and medium density fiberboard properties

    Treesearch

    Todd F. Shupe; Chung Y. Hse; Elvin T. Choong; Leslie H. Groom

    1999-01-01

    he objective of this study was to determine the effect of five different silvicultural strategies and wood type on mechanical and physical properties of loblolly pine (Pinus taeda L.) particleboard and fiberboard. The furnish was prepared in an unconventional manner from innerwood and outerwood veneer for each stand. Modulus of rupture (MOR)...

  12. New rapid method for determining edgewise compressive strength of corrugated fiberboard

    Treesearch

    John W. Koning

    1986-01-01

    The objective of this study was to determine if corrugated fiberboard specimens that had been necked down with a common router would yield acceptable edgewise compressive strength values. Tests were conducted on specimens prepared using a circular saw and router, and the results were compared with those obtained on specimens prepared according to TAPPI Test Method T...

  13. High-frequency and hot-platen curing of medium-density fiberboards

    Treesearch

    R.R. Stevens; G.E. Woodson

    1977-01-01

    The effects of two curing methods- high-frequency heating and hot-platen heating- on the properties of a ure-formaldehyd-bonded medium-density fiberboard prepared with a southern-hardwoods furnish (50% southern red oak, 25% mockernut hickory, and 25% sweetgum) were studied. Boards of three densities- 38, 44, and 50 lb./ft.3- were cured by the two...

  14. Three-dimensional engineered fiberboard : opportunities for the use of low valued timber and recycled material

    Treesearch

    John F. Hunt; David P. Harper; Katherine A. Friedrich

    2004-01-01

    Fiberboard sandwich panels constructed of a structural core with exterior skins can be produced with high strength and stiffness values that compare to other wood-based panels. At the same time, as much as two-thirds less material is used in the process compared to commercial wood composite products. This offers large savings in raw material and weight. The panel...

  15. Effects of fiber processing on properties of fiber and fiberboard made from lodgepole pine treetops

    Treesearch

    John F. Hunt; Aziz Ahmed; Katherine Friedrich

    2008-01-01

    As a part of the National Fire Plan, the USDA Forest Service is conducting research to reduce the severity of forest fires through effective utilization of low-or no-value logging residues and forest thinnings. This report explores the effect of processing on the physical properties of the fibrous material and flat fiberboard panels made from small-diameter lodgepole...

  16. 3D engineered fiberboard : finite element analysis of a new building product

    Treesearch

    John F. Hunt

    2004-01-01

    This paper presents finite element analyses that are being used to analyze and estimate the structural performance of a new product called 3D engineered fiberboard in bending and flat-wise compression applications. A 3x3x2 split-plot experimental design was used to vary geometry configurations to determine their effect on performance properties. The models are based on...

  17. Analysis of Cantilever-Beam Bending Stress Relaxation Properties of Thin Wood Composites

    Treesearch

    John F. Hunt; Houjiang Zhang; Yan Huang

    2015-01-01

    An equivalent strain method was used to analyze and determine material relaxation properties for specimens from particleboard, high density fiberboard, and medium density fiberboard. Cantilever beams were clamped and then deflected to 11 m and held for either 2 h or 3 h, while the load to maintain that deflection was measured vs. time. Plots of load relaxation for each...

  18. Effect of oxalic acid pretreatment of wood chips on manufacturing medium-density fiberboard

    Treesearch

    Xianjun Li; Zhiyong Cai; Eric Horn; Jerrold E. Winandy

    2011-01-01

    The main objective of this study was to evaluate the effect of oxalic acid (OA) wood chips pretreatment prior to refining, which is done to reduce energy used during the refining process. Selected mechanical and physical performances of medium-density fiberboard (MDF) – internal bonding (IB), modulus of elasticity (MOE), modulus of rupture (MOR), water absorption (WA)...

  19. Examination of Shipping Packages 9975-02694 and 9975-02729

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W.

    SRNL has assisted in the examination of two 9975 shipping packages (9975-02694 and 9975-02729) following their use for storage of nuclear material in K-Area Complex (KAC). Both of these were targeted for examination because they were exposed to water from a leaking expansion joint during storage. When first opened in KAC, the axial gap was found to be in excess of the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Within each package the highest fiberboard moisture levels were observed in the bottom layers, but no mold was observed in either package. Themore » fiberboard in each package appeared to retain good integrity consistent with non-degraded material. Minor corrosion was also observed on these drums along the lower stitch welds and on several closure bolts.« less

  20. Preliminary statistical studies concerning the Campos RJ sugar cane area, using LANDSAT imagery and aerial photographs

    NASA Technical Reports Server (NTRS)

    Parada, N. D. J. (Principal Investigator); Costa, S. R. X.; Paiao, L. B. F.; Mendonca, F. J.; Shimabukuro, Y. E.; Duarte, V.

    1983-01-01

    The two phase sampling technique was applied to estimate the area cultivated with sugar cane in an approximately 984 sq km pilot region of Campos. Correlation between existing aerial photography and LANDSAT data was used. The two phase sampling technique corresponded to 99.6% of the results obtained by aerial photography, taken as ground truth. This estimate has a standard deviation of 225 ha, which constitutes a coefficient of variation of 0.6%.

  1. Elasticity and inelasticity of biomorphic carbon, silicon carbide, and SiC/Si composite produced on the basis of medium density fiberboard

    NASA Astrophysics Data System (ADS)

    Kardashev, B. K.; Orlova, T. S.; Smirnov, B. I.; de Arellano-Lopez, A. R.; Martinez-Fernandez, J.

    2010-10-01

    The amplitude and temperature dependences of the Young’s modulus and the internal friction (ultrasonic absorption) of biomorphic carbon, silicon carbide, and SiC/Si composite produced from medium density fiberboard (MDF) by pyrolysis (carbonization), followed by infiltration of molten silicon into the prepared carbon preform have been studied in the temperature range 100-293 K in air and under vacuum. The measurements have been performed by the acoustic resonance method with the use of a composite vibrator for longitudinal vibrations at frequencies of approximately 100 kHz. The data obtained by acoustic measurements of the amplitude dependences of the elastic modulus have been used for evaluating the microplastic properties of samples under study. It has been shown that the Young’s modulus, the decrement of elastic vibrations, and the conventional microyield strength of the MDF samples differ from the corresponding data for previously studied similar materials produced from natural eucalyptus, beech, sapele, and pine woods. In particular, the desorption of environmental molecules at small amplitudes of vibrations, which is typical of biomorphic materials based on natural wood, is almost absent for the MDF samples. The results obtained have been explained by different structures and the influence of pores and other defects, which, to a large extent, determine the mechanical characteristics of the biomaterials under investigation.

  2. Effects of bark, density profile, and resin content on medium-density fiberboards from southern hardwoods

    Treesearch

    G.E. Woodson

    1976-01-01

    Pressure-regined barky fibers of hickory, sweetgum, and southern red oak had a greater percentage of fines than did refined bark-free fibers of these species. Inclusion of bark decreased tensile and bending strengths of fiberboards by 16 to 18 percent, MOE by 10 to 14 percent, and IB by 8 percent. Density profile of boards strongly influenced their bending properties...

  3. Fiberboards treated with N’-N-(1, 8-Naphthalyl) hydroxylamine (NHA-Na), borax, and boric acid

    Treesearch

    Turgay Akbulut; S. Nami Kartal; Frederick Green

    2004-01-01

    This paper reports on the physical and mechanical properties and decay and termite resistance of fiberboard panels made from pine and beech treated with N’-N-(1, 8-Naphthalyl) hydroxylamine sodium salt(NHA-Na), borax, and boric acid at varying loadings. The panels were manufactured using 10 percent urea-formaldehyde resin and 1 percent NH4Cl. Mechanical and physical...

  4. Fiberboard bending properties as a function of density, thickness, resin, and moisture content

    Treesearch

    John F. Hunt; Jane O' Dell; Chris Turk

    2008-01-01

    Fibers from treetop residues of lodgepole pine (Pinus contorta) and recycled old corrugated containers were used to fabricate wet-formed fiberboard panels over a range of densities from 300 to 1100 kg m-3, a thickness range from 1.3 to 4.8 mm, and phenolic resin contents from 0% to 4.5%. The panels were then tested after conditioning in 50% and 90% relative humidity (...

  5. Characterization of Emissions from Open Burning of Meals ...

    EPA Pesticide Factsheets

    Emissions from burning current and candidate Meals Ready-to-Eat (MRE) packaging and shipping containers were characterized in an effort to assuage concerns that combustive disposal of waste at forward operating bases could pose an environmental or inhalation threat. Four types of container materials, both box and liners, including the currently used fiberboard, new corrugated fiberboard with Spektrakote polymer, new fiberboard without Spektrakote polymer, and the current fiberboard without wet strength were burned in an open burn test facility that simulated the burn pit disposal methods in Iraq and Afghanistan. MREs, including both current and proposed packaging materials, were added to a single container type to examine their effect on emissions. One quarter of the food was left in the packaging to represent unused meal components. The proposed packaging, consisting of a nano-composite polymer, was added in 25 % increments compared to traditional MRE packaging to create a range of usage levels. Emission factors, mass of pollutant per mass of burned material, were increased over the emission factors of the package containers themselves by the addition of the multi-component MREs, with the exception of Volatile Organic Compounds (VOCs). In general, little distinction was observed when comparing emission factors from the four container materials and when comparing the four MRE compositions. The majority of Particulate Matter (PM) emissions were of particles that

  6. Changes in the chemical composition and spectroscopy of loblolly pine medium density fiberboard furnish as a function of age and refining pressure

    Treesearch

    Stephen S. Kelley; Thomas Elder; Leslie H. Groom

    2005-01-01

    Loblolly pine wood between the ages of 5-35 was refined into medium density fiberboard furnish at steam pressures from 2 to 18 bar, The effect of age and processing conditions on the properties of the fibers was assessed by wet chemical analyses, Near Infared Spectroscopy (NIR) and powder X-ray diffraction (XRD).In general ,the percentages of extractives and glucose...

  7. Changes in the physicochemical characteristics, including flavour components and Maillard reaction products, of non-centrifugal cane brown sugar during storage.

    PubMed

    Asikin, Yonathan; Kamiya, Asahiro; Mizu, Masami; Takara, Kensaku; Tamaki, Hajime; Wada, Koji

    2014-04-15

    Changes in the quality attributes of non-centrifugal cane brown sugar represented by physicochemical characteristics as well as flavour components and Maillard reaction products (MRPs) were monitored every 3 months over 1 year of storage. Stored cane brown sugar became darker, and its moisture content and water activity (a(w)) increased during storage. Fructose and glucose levels decreased as non-enzymatic browning via the Maillard reaction occurred in the stored sample, and a similar trend was also discovered in aconitic and acetic acids. Stored cane brown sugar lost its acidic and sulfuric odours (58.70-39.35% and 1.85-0.08%, respectively); subsequently, the nutty and roasted aroma increased from 26.52% to 38.59% due to the volatile MRPs. The browning rate of stored cane brown sugar was positively associated with the development of volatile MRPs (Pearson's coefficient = 0.860), whereas the amount of 3-deoxyglucosone, an intermediate product of the Maillard reaction, had a lower association with the brown colour due to its relatively slow degradation rate. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Payback time for soil carbon and sugar-cane ethanol

    NASA Astrophysics Data System (ADS)

    Mello, Francisco F. C.; Cerri, Carlos E. P.; Davies, Christian A.; Holbrook, N. Michele; Paustian, Keith; Maia, Stoécio M. F.; Galdos, Marcelo V.; Bernoux, Martial; Cerri, Carlos C.

    2014-07-01

    The effects of land-use change (LUC) on soil carbon (C) balance has to be taken into account in calculating the CO2 savings attributed to bioenergy crops. There have been few direct field measurements that quantify the effects of LUC on soil C for the most common land-use transitions into sugar cane in Brazil, the world's largest producer . We quantified the C balance for LUC as a net loss (carbon debt) or net gain (carbon credit) in soil C for sugar-cane expansion in Brazil. We sampled 135 field sites to 1 m depth, representing three major LUC scenarios. Our results demonstrate that soil C stocks decrease following LUC from native vegetation and pastures, and increase where cropland is converted to sugar cane. The payback time for the soil C debt was eight years for native vegetation and two to three years for pastures. With an increasing need for biofuels and the potential for Brazil to help meet global demand, our results will be invaluable for guiding expansion policies of sugar-cane production towards greater sustainability.

  9. Examination of shipping packages 9975-01641, 9975-01692, 9975-03373, 9975-02101 AND 9975-02713

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    SRNL has assisted in the examination of five 9975 shipping packages following storage of nuclear material in K-Area Complex (KAC). Two packages (9975-01641 and -01692) with water intrusion resulting from a roof leak were selected for detailed examination after internal fiberboard degradation (mold) was observed. 9975-01692 contained regions of saturated fiberboard and significant mold, while the second package was less degraded. A third package (9975-03373) was removed from storage for routine surveillance activities, and set aside for further examination after a musty odor was noted inside. No additional degradation was noted in 9975-03373, but the lower assembly could not bemore » removed from the drum for detailed examination. Two additional packages (9975-02101 and -02713) identified for further examination were among a larger group selected for surveillance as part of a specific focus on high-wattage packages. These two packages displayed several non-conforming conditions, including the following: (1) the axial gap criterion was exceeded, (2) a significant concentration of moisture was found in the bottom fiberboard layers, with active mold in this area, (3) condensation and/or water stains were observed on internal components (drum, lid, air shield), and (4) both drums contained localized corrosion along the bottom lip. It is recommended that a new screening check be implemented for packages that are removed from storage, as well as high wattage packages remaining in storage. An initial survey for corrosion along the drum bottom lip of high wattage packages could identify potential degraded packages for future surveillance focus. In addition, after packages have been removed from storage (and unloaded), the drum bottom lip and underside should be inspected for corrosion. The presence of corrosion could signal the need to remove the lower fiberboard assembly for further inspection of the fiberboard and drum prior to recertification of the package.« less

  10. Unintentional fall injuries associated with walkers and canes in older adults treated in U.S. emergency departments.

    PubMed

    Stevens, Judy A; Thomas, Karen; Teh, Leesia; Greenspan, Arlene I

    2009-08-01

    To characterize nonfatal, unintentional, fall-related injuries associated with walkers and canes in older adults. Surveillance data of injuries treated in hospital emergency departments (EDs), January 1, 2001, to December 31, 2006. The National Electronic Injury Surveillance System All Injury Program, which collects data from a nationally representative stratified probability sample of 66 U.S. hospital EDs. People aged 65 and older treated in EDs for 3,932 nonfatal unintentional fall injuries and whose records indicated that a cane or a walker was involved in the fall. Sex, age, whether the fall involved a cane or walker, primary diagnosis, part of the body injured, disposition, and location and circumstances of the fall. An estimated 47,312 older adult fall injuries associated with walking aids were treated annually in U.S. EDs: 87.3% with walkers, 12.3% with canes, and 0.4% with both. Walkers were associated with seven times as many injuries as canes. Women's injury rates exceeded those for men (rate ratios=2.6 for walkers, 1.4 for canes.) The most prevalent injuries were fractures and contusions or abrasions. Approximately one-third of subjects were hospitalized for their injuries. Injuries and hospital admissions for falls associated with walking aids were frequent in this highly vulnerable population. The results suggest that more research is needed to improve the design of walking aids. More information also is needed about the circumstances preceding falls, both to better understand the contributing fall risk factors and to develop specific and effective fall prevention strategies.

  11. Physicochemical and sensory (aroma and colour) characterisation of a non-centrifugal cane sugar ("panela") beverage.

    PubMed

    García, Juliana María; Narváez, Paulo César; Heredia, Francisco José; Orjuela, Álvaro; Osorio, Coralia

    2017-08-01

    Non-centrifugal cane sugar (NCS), also called "panela", is a high carbohydrate-content food obtained by boil evaporation of the sugar cane juice. This study was undertaken to assess physicochemical properties and sensory characteristics of panela beverage at two different concentrations. Evaluation of pH, °Brix, and colour (tristimulus colorimetry) was carried out in all panela drink samples. In order to characterise the odour-active volatiles of the beverage, a simultaneous steam distillation-solvent extraction method was applied using a mixture of diethyl ether-pentane (1:1,w/w) as solvent. The Aroma Extract Dilution Analysis revealed the presence of six odour-active compounds, being 2-methyl pyrazine the key aroma compound of this beverage. PCA (Principal Component Analysis) showed that there were no differences in the aroma and physicochemical properties (pH and °Brix) with respect to the geographical origin of analysed samples; however colour depends on heating during processing of NCS. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Sugar markers in aerosol particles from an agro-industrial region in Brazil

    NASA Astrophysics Data System (ADS)

    Urban, R. C.; Alves, C. A.; Allen, A. G.; Cardoso, A. A.; Queiroz, M. E. C.; Campos, M. L. A. M.

    2014-06-01

    This work aimed to better understand how aerosol particles from sugar cane burning contribute to the chemical composition of the lower troposphere in an agro-industrial region of São Paulo State (Brazil) affected by sugar and ethanol fuel production. During a period of 21 months, we collected 105 samples and quantified 20 saccharides by GC-MS. The average concentrations of levoglucosan (L), mannosan (M), and galactosan (G) for 24-h sampling were 116, 16, and 11 ng m-3 respectively. The three anhydrosugars had higher and more variable concentrations in the nighttime and during the sugar cane harvest period, due to more intense biomass burning practices. The calculated L/M ratio, which may serve as a signature for sugar cane smoke particles, was 9 ± 5. Although the total concentrations of the anhydrosugars varied greatly among samples, the relative mass size distributions of the saccharides were reasonably constant. Emissions due to biomass burning were estimated to correspond to 69% (mass) of the sugars quantified in the harvest samples, whereas biogenic emissions corresponded to 10%. In the non-harvest period, these values were 44 and 27%, respectively, indicating that biomass burning is an important source of aerosol to the regional atmosphere during the whole year.

  13. Drop-off detection with the long cane: effect of cane shaft weight and rigidity on performance

    PubMed Central

    Kim, Dae Shik; Emerson, Robert Wall; Naghshineh, Koorosh; Auer, Alexander

    2016-01-01

    Most travellers who are blind rely on a long cane to detect drop-offs on their walking paths. We examined how different cane shaft materials affect drop-off detection performance through providing different vibrotactile and proprioceptive feedbacks to the cane user. Results of the study showed a significant interaction between cane shaft weight and how the cane is used. A heavier cane was advantageous for detecting drop-offs when the individual used the ‘constant contact technique’ – cane tip stays in contact with the walking surface at all times – but not when he used the ‘two-point touch technique’ – cane tip is rhythmically tapped on the surface. In addition, a more flexible cane was advantageous for detecting drop-offs when the two-point touch technique was used but not when the constant contact technique was used. It is recommended that, when blind individuals select a cane shaft material, they consider which long cane technique they use more often. Practitioner Summary: Long cane shaft material affects how well a blind individual can detect drop-offs. A heavier shaft was advantageous when using the constant contact technique (cane tip stays in continuous contact with the surface), while a more flexible shaft was better when using the two-point touch technique (cane tip rhythmically taps the surface). PMID:27065052

  14. Effect of cane length and swing arc width on drop-off and obstacle detection with the long cane

    PubMed Central

    Kim, Dae Shik; Emerson, Robert Wall; Naghshineh, Koorosh

    2017-01-01

    A repeated-measures design with block randomization was used for the study, in which 15 adults with visual impairments attempted to detect the drop-offs and obstacles with the canes of different lengths, swinging the cane in different widths (narrow vs wide). Participants detected the drop-offs significantly more reliably with the standard-length cane (79.5% ± 6.5% of the time) than with the extended-length cane (67.6% ± 9.1%), p <.001. The drop-off detection threshold of the standard-length cane (4.1 ± 1.1 cm) was also significantly smaller than that of the extended-length cane (6.5±1.8cm), p <.001. In addition, participants detected drop-offs at a significantly higher percentage when they swung the cane approximately 3 cm beyond the widest part of the body (78.6% ± 7.6%) than when they swung it substantially wider (30 cm; 68.5% ± 8.3%), p <.001. In contrast, neither cane length (p =.074) nor cane swing arc width (p =.185) had a significant effect on obstacle detection performance. The findings of the study may help orientation and mobility specialists recommend appropriate cane length and cane swing arc width to visually impaired cane users. PMID:29276326

  15. Effect of cane length and swing arc width on drop-off and obstacle detection with the long cane.

    PubMed

    Kim, Dae Shik; Emerson, Robert Wall; Naghshineh, Koorosh

    2017-09-01

    A repeated-measures design with block randomization was used for the study, in which 15 adults with visual impairments attempted to detect the drop-offs and obstacles with the canes of different lengths, swinging the cane in different widths (narrow vs wide). Participants detected the drop-offs significantly more reliably with the standard-length cane (79.5% ± 6.5% of the time) than with the extended-length cane (67.6% ± 9.1%), p <.001. The drop-off detection threshold of the standard-length cane (4.1 ± 1.1 cm) was also significantly smaller than that of the extended-length cane (6.5±1.8cm), p <.001. In addition, participants detected drop-offs at a significantly higher percentage when they swung the cane approximately 3 cm beyond the widest part of the body (78.6% ± 7.6%) than when they swung it substantially wider (30 cm; 68.5% ± 8.3%), p <.001. In contrast, neither cane length ( p =.074) nor cane swing arc width ( p =.185) had a significant effect on obstacle detection performance. The findings of the study may help orientation and mobility specialists recommend appropriate cane length and cane swing arc width to visually impaired cane users.

  16. Direct Zinc Determination in Brazilian Sugar Cane Spirit by Solid-Phase Extraction Using Moringa oleifera Husks in a Flow System with Detection by FAAS.

    PubMed

    Alves, Vanessa N; Borges, Simone S O; Coelho, Nivia M M

    2011-01-01

    This paper reports a method for the determination of zinc in Brazilian sugar cane spirit, (cachaça in Portuguese), using solid-phase extraction with a flow injection analysis system and detection by FAAS. The sorbent material used was activated carbon obtained from Moringa oleifera husks. Flow and chemical variables of the proposed system were optimized through multivariate designs. The factors selected were sorbent mass, sample pH, sample flow rate, and eluent concentration. The optimum extraction conditions were obtained using a sample pH of 4.0, a sample flow rate of 6.0 mL min(-1), 30.0 mg of sorbent mass, and 1.0 mol L(-1) HNO(3) as the eluent at a flow rate of 4.0 mL min(-1). The limit of detection for zinc was 1.9 μg L(-1), and the precision was below 0.82% (20.0 μg L(-1), n = 7). The analytical curve was linear from 2 to 50 μg L(-1), with a correlation coefficient of 0.9996. The method developed was successfully applied to spiked Brazilian sugar cane spirit, and accuracy was assessed through recovery tests, with results ranging from 83% to 100%.

  17. Direct Zinc Determination in Brazilian Sugar Cane Spirit by Solid-Phase Extraction Using Moringa oleifera Husks in a Flow System with Detection by FAAS

    PubMed Central

    Alves, Vanessa N.; Borges, Simone S. O.; Coelho, Nivia M. M.

    2011-01-01

    This paper reports a method for the determination of zinc in Brazilian sugar cane spirit, (cachaça in Portuguese), using solid-phase extraction with a flow injection analysis system and detection by FAAS. The sorbent material used was activated carbon obtained from Moringa oleifera husks. Flow and chemical variables of the proposed system were optimized through multivariate designs. The factors selected were sorbent mass, sample pH, sample flow rate, and eluent concentration. The optimum extraction conditions were obtained using a sample pH of 4.0, a sample flow rate of 6.0 mL min−1, 30.0 mg of sorbent mass, and 1.0 mol L−1 HNO3 as the eluent at a flow rate of 4.0 mL min−1. The limit of detection for zinc was 1.9 μg L−1, and the precision was below 0.82% (20.0 μg L−1, n = 7). The analytical curve was linear from 2 to 50 μg L−1, with a correlation coefficient of 0.9996. The method developed was successfully applied to spiked Brazilian sugar cane spirit, and accuracy was assessed through recovery tests, with results ranging from 83% to 100%. PMID:21785595

  18. Assessment of canes used by older adults in senior living communities.

    PubMed

    Liu, Hao Howe; Eaves, Joshua; Wang, Wen; Womack, Jill; Bullock, Paige

    2011-01-01

    The purpose of this cross-sectional study is to provide basic but essential information about how older cane users obtain their canes and how they use these canes for their daily mobility, since there is still lack of information on these areas. Ninety-three older (≥65 years old) subjects who use canes for daily activities were recruited from four assisted living facilities and five retirement centers for this cross-sectional study. The assessment involved interviewing cane users with a questionnaire, examining their canes, and investigating how these canes were used by their owners during ambulation. The commonly used canes are (from most to least): adjustable single-tip, un-adjustable (wooden), small quad, and large quad. Five major problems from data analysis were identified: lack of medical consultation for device selection/use, incorrect cane height/maintenance, placement of cane in improper hand, inability to maintain the proper reciprocal gait pattern, and improper posture during ambulation. Only forward-leaning posture during ambulation might be associated with increased falls among the older cane users. Knowledge of these problems could assist health professionals to implement appropriate interventions in clinical settings and to provide community service to address all problems related to cane use. Published by Elsevier Ireland Ltd.

  19. The effect of extended sensory range via the EyeCane sensory substitution device on the characteristics of visionless virtual navigation.

    PubMed

    Maidenbaum, Shachar; Levy-Tzedek, Shelly; Chebat, Daniel Robert; Namer-Furstenberg, Rinat; Amedi, Amir

    2014-01-01

    Mobility training programs for helping the blind navigate through unknown places with a White-Cane significantly improve their mobility. However, what is the effect of new assistive technologies, offering more information to the blind user, on the underlying premises of these programs such as navigation patterns? We developed the virtual-EyeCane, a minimalistic sensory substitution device translating single-point-distance into auditory cues identical to the EyeCane's in the real world. We compared performance in virtual environments when using the virtual-EyeCane, a virtual-White-Cane, no device and visual navigation. We show that the characteristics of virtual-EyeCane navigation differ from navigation with a virtual-White-Cane or no device, and that virtual-EyeCane users complete more levels successfully, taking shorter paths and with less collisions than these groups, and we demonstrate the relative similarity of virtual-EyeCane and visual navigation patterns. This suggests that additional distance information indeed changes navigation patterns from virtual-White-Cane use, and brings them closer to visual navigation.

  20. Ergonomic factors related to drop-off detection with the long cane: effects of cane tips and techniques.

    PubMed

    Kim, Dae Shik; Emerson, Robert S Wall; Curtis, Amy B

    2010-06-01

    This study examined the effect of cane tips and cane techniques on drop-off detection with the long cane. Blind pedestrians depend on a long cane to detect drop-offs. Missing a drop-off may result in falls or collision with moving vehicles in the street. Although cane tips appear to affect a cane user's ability to detect drop-offs, few experimental studies have examined such effect. A repeated-measures design with block randomization was used for the study. Participants were 17 adults who were legally blind and had no other disabilities. Participants attempted to detect the drop-offs of varied depths using different cane tips and cane techniques. Drop-off detection rates were similar between the marshmallow tip (77.0%) and the marshmallow roller tip (79.4%) when both tips were used with the constant contact technique, p = .294. However, participants detected drop-offs at a significantly higher percentage when they used the constant contact technique with the marshmallow roller tip (79.4%) than when they used the two-point touch technique with the marshmallow tip (63.2%), p < .001. The constant contact technique used with a marshmallow roller tip (perceived as a less advantageous tip) was more effective than the two-point touch technique used with a marshmallow tip (perceived as a more advantageous tip) in detecting drop-offs. The findings of the study may help cane users and orientation and mobility specialists select appropriate cane techniques and cane tips in accordance with the cane user's characteristics and the nature of the travel environment.

  1. Firmicutes dominate the bacterial taxa within sugar-cane processing plants

    PubMed Central

    Sharmin, Farhana; Wakelin, Steve; Huygens, Flavia; Hargreaves, Megan

    2013-01-01

    Sugar cane processing sites are characterised by high sugar/hemicellulose levels, available moisture and warm conditions, and are relatively unexplored unique microbial environments. The PhyloChip microarray was used to investigate bacterial diversity and community composition in three Australian sugar cane processing plants. These ecosystems were highly complex and dominated by four main Phyla, Firmicutes (the most dominant), followed by Proteobacteria, Bacteroidetes, and Chloroflexi. Significant variation (p < 0.05) in community structure occurred between samples collected from ‘floor dump sediment’, ‘cooling tower water’, and ‘bagasse leachate’. Many bacterial Classes contributed to these differences, however most were of low numerical abundance. Separation in community composition was also linked to Classes of Firmicutes, particularly Bacillales, Lactobacillales and Clostridiales, whose dominance is likely to be linked to their physiology as ‘lactic acid bacteria’, capable of fermenting the sugars present. This process may help displace other bacterial taxa, providing a competitive advantage for Firmicutes bacteria. PMID:24177592

  2. Walking Distance Estimation Using Walking Canes with Inertial Sensors

    PubMed Central

    Suh, Young Soo

    2018-01-01

    A walking distance estimation algorithm for cane users is proposed using an inertial sensor unit attached to various positions on the cane. A standard inertial navigation algorithm using an indirect Kalman filter was applied to update the velocity and position of the cane during movement. For quadripod canes, a standard zero-velocity measurement-updating method is proposed. For standard canes, a velocity-updating method based on an inverted pendulum model is proposed. The proposed algorithms were verified by three walking experiments with two different types of canes and different positions of the sensor module. PMID:29342971

  3. Wearable Virtual White Cane Network for navigating people with visual impairment.

    PubMed

    Gao, Yabiao; Chandrawanshi, Rahul; Nau, Amy C; Tse, Zion Tsz Ho

    2015-09-01

    Navigating the world with visual impairments presents inconveniences and safety concerns. Although a traditional white cane is the most commonly used mobility aid due to its low cost and acceptable functionality, electronic traveling aids can provide more functionality as well as additional benefits. The Wearable Virtual Cane Network is an electronic traveling aid that utilizes ultrasound sonar technology to scan the surrounding environment for spatial information. The Wearable Virtual Cane Network is composed of four sensing nodes: one on each of the user's wrists, one on the waist, and one on the ankle. The Wearable Virtual Cane Network employs vibration and sound to communicate object proximity to the user. While conventional navigation devices are typically hand-held and bulky, the hands-free design of our prototype allows the user to perform other tasks while using the Wearable Virtual Cane Network. When the Wearable Virtual Cane Network prototype was tested for distance resolution and range detection limits at various displacements and compared with a traditional white cane, all participants performed significantly above the control bar (p < 4.3 × 10(-5), standard t-test) in distance estimation. Each sensor unit can detect an object with a surface area as small as 1 cm(2) (1 cm × 1 cm) located 70 cm away. Our results showed that the walking speed for an obstacle course was increased by 23% on average when subjects used the Wearable Virtual Cane Network rather than the white cane. The obstacle course experiment also shows that the use of the white cane in combination with the Wearable Virtual Cane Network can significantly improve navigation over using either the white cane or the Wearable Virtual Cane Network alone (p < 0.05, paired t-test). © IMechE 2015.

  4. Ergonomic Factors Related to Drop-Off Detection With the Long Cane: Effects of Cane Tips and Techniques

    PubMed Central

    Kim, Dae Shik; Wall Emerson, Robert S.; Curtis, Amy B.

    2010-01-01

    Objective This study examined the effect of cane tips and cane techniques on drop-off detection with the long cane. Background Blind pedestrians depend on a long cane to detect drop-offs. Missing a drop-off may result in falls or collision with moving vehicles in the street. Although cane tips appear to affect a cane user’s ability to detect drop-offs, few experimental studies have examined such effect. Method A repeated-measures design with block randomization was used for the study. Participants were 17 adults who were legally blind and had no other disabilities. Participants attempted to detect the drop-offs of varied depths using different cane tips and cane techniques. Results Drop-off detection rates were similar between the marshmallow tip (77.0%) and the marshmallow roller tip (79.4%) when both tips were used with the constant contact technique, p = .294. However, participants detected drop-offs at a significantly higher percentage when they used the constant contact technique with the marshmallow roller tip (79.4%) than when they used the two-point touch technique with the marshmallow tip (63.2%), p < .001. Conclusion The constant contact technique used with a marshmallow roller tip (perceived as a less advantageous tip) was more effective than the two-point touch technique used with a marshmallow tip (perceived as a more advantageous tip) in detecting drop-offs. Application The findings of the study may help cane users and orientation and mobility specialists select appropriate cane techniques and cane tips in accordance with the cane user’s characteristics and the nature of the travel environment. PMID:21077566

  5. Land Use Influences Niche Size and the Assimilation of Resources by Benthic Macroinvertebrates in Tropical Headwater Streams

    PubMed Central

    Parreira de Castro, Diego Marcel; Reis de Carvalho, Débora; Pompeu, Paulo dos Santos; Moreira, Marcelo Zacharias; Nardoto, Gabriela Bielefeld; Callisto, Marcos

    2016-01-01

    It is well recognized that assemblage structure of stream macroinvertebrates changes with alterations in catchment or local land use. Our objective was to understand how the trophic ecology of benthic macroinvertebrate assemblages responds to land use changes in tropical streams. We used the isotope methodology to assess how energy flow and trophic relations among macroinvertebrates were affected in environments affected by different land uses (natural cover, pasture, sugar cane plantation). Macroinvertebrates were sampled and categorized into functional feeding groups, and available trophic resources were sampled and evaluated for the isotopic composition of 13C and 15N along streams located in the Cerrado (neotropical savanna). Streams altered by pasture or sugar cane had wider and more overlapped trophic niches, which corresponded to more generalist feeding habits. In contrast, trophic groups in streams with native vegetation had narrower trophic niches with smaller overlaps, suggesting greater specialization. Pasture sites had greater ranges of resources exploited, indicating higher trophic diversity than sites with natural cover and sugar cane plantation. We conclude that agricultural land uses appears to alter the food base and shift macroinvertebrate assemblages towards more generalist feeding behaviors and greater overlap of the trophic niches. PMID:26934113

  6. Land Use Influences Niche Size and the Assimilation of Resources by Benthic Macroinvertebrates in Tropical Headwater Streams.

    PubMed

    Parreira de Castro, Diego Marcel; Reis de Carvalho, Débora; Pompeu, Paulo dos Santos; Moreira, Marcelo Zacharias; Nardoto, Gabriela Bielefeld; Callisto, Marcos

    2016-01-01

    It is well recognized that assemblage structure of stream macroinvertebrates changes with alterations in catchment or local land use. Our objective was to understand how the trophic ecology of benthic macroinvertebrate assemblages responds to land use changes in tropical streams. We used the isotope methodology to assess how energy flow and trophic relations among macroinvertebrates were affected in environments affected by different land uses (natural cover, pasture, sugar cane plantation). Macroinvertebrates were sampled and categorized into functional feeding groups, and available trophic resources were sampled and evaluated for the isotopic composition of 13C and 15N along streams located in the Cerrado (neotropical savanna). Streams altered by pasture or sugar cane had wider and more overlapped trophic niches, which corresponded to more generalist feeding habits. In contrast, trophic groups in streams with native vegetation had narrower trophic niches with smaller overlaps, suggesting greater specialization. Pasture sites had greater ranges of resources exploited, indicating higher trophic diversity than sites with natural cover and sugar cane plantation. We conclude that agricultural land uses appears to alter the food base and shift macroinvertebrate assemblages towards more generalist feeding behaviors and greater overlap of the trophic niches.

  7. Effect of a cane on sit-to-stand transfer in subjects with hemiparesis.

    PubMed

    Hu, Po-Ting; Lin, Kwan-Hwa; Lu, Tung-Wu; Tang, Pei-Fang; Hu, Ming-Hsia; Lai, Jin-Shin

    2013-03-01

    The aim of this study was to determine the effect of using a cane on movement time, joint moment, weight symmetry, and muscle activation patterns during sit-to-stand (STS) transfer in healthy subjects and subjects who have had a stroke. Nine subjects with hemiparesis (mean [SD] age, 61.11 [12.83] yrs) and nine healthy adults (mean [SD] age, 63.11 [10.54] yrs) were included. The subjects with hemiparesis performed STS transfer in two randomly assigned conditions: (1) without a cane and (2) with a cane. The healthy subjects performed only STS transfer without a cane. A three-dimensional motion system, force plates, and eletromyography were used to examine STS transfer. The symmetry index between the two limbs was calculated. The movement time of the subjects with hemiparesis in both conditions without a cane and with a cane was longer than that of the healthy subjects without a cane (P < 0.025). However, STS transfer with a cane in the subjects with hemiparesis resulted in shorter movement time, greater knee extensor moment of the paretic limb, and more symmetry of weight bearing than in those without a cane (P < 0.05). The sequence of muscle onset tended to improve with a cane in the subjects with hemiparesis. Cane use may promote more symmetrical STS transfers rather than compensation by the unaffected limb.

  8. Comparison of Spectrophotometric Methods for the Determination of Copper in Sugar Cane Spirit.

    PubMed

    Soares, Sarah Adriana R; Costa, Silvânio Silvério L; Araujo, Rennan Geovanny O; Teixeira, Leonardo Sena Gomes; Dantas, Alailson Falcão

    2018-05-01

    Three spectrophotometric methods were developed for the determination of copper (Cu) in sugar cane spirit using the chromogenic reagents neocuproine, cuprizone, and bathocuproine. Experimental conditions, such as reagent concentration, reducer concentration, pH, buffer concentration, the order of addition of reagents, and the stability of the complexes, were optimized. The work range was established from 1.0 to 10.0 µg/mL, with correlation coefficients of >0.999 for all three optimized methods. The methods were evaluated regarding accuracy by addition and recovery tests at five concentration levels, and the obtained recoveries ranged from 91 to 105% (n = 3). Precision was expressed as RSD (relative standard deviation), with values ranging from 0.01 to 0.17% (n = 10). The method using the chromogenic reagent cuprizone presented the greatest molar absorptivity, followed by bathocuproine and neocuproine. The methods were applied for the determination of Cu in sugar cane spirit, and the results were compared with a reference method by flame atomic absorption spectrometry (FAAS). Calibration curve solutions for FAAS analysis were prepared in a 40% (v/v) alcohol medium in a range of concentrations from 0.5 up to 5 µg/mL. Measurements for Cu determination were carried out at a wavelength of 324.7 nm. The concentrations obtained for Cu in sugar cane spirit samples from Brazil were between 1.99 and 12.63 µg/mL, and about 75% of the samples presented Cu concentrations above the limit established by Brazilian legislation (5.0 µg/mL or 5.0 mg/L).

  9. The energy cane alternative

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Alexander, A.G.

    This book reviews the conceptual and theoretical background of Saccharum botany, which underlies the growing of cane as a total growth commodity. Management details are provided for energy cane planting, cultivation, harvest, and postharvest operations. Chapters on energy cane utilization stress new developments in lignocellulose conversion plus alternative options for fermentable solids usage. Chapters are also included for the management of alternative grasses to supplement energy cane, and the breeding of new hybrid canes with high biomass attributes at the intergeneric and interspecific levels.

  10. Use of a cane for recovery from backward balance loss during treadmill walking.

    PubMed

    Hyodo, Masaki; Saito, Mayumi; Ushiba, Junichi; Tomita, Yutaka; Masakado, Yoshihisa

    2013-06-01

    To study whether a cane improved balance recovery after perturbation during walking. This study was a crossover comparison comparing the effect of walking with and without a cane for balance recovery after perturbation during treadmill walking. Five normal young volunteers participated. The velocity and acceleration of a marker sited on the seventh cerebral vertebra (C7) and vertical hand motion were measured by a motion analysis system. When using a cane, C7 backward velocity increased by approximately 15% (413 SD 95 mm/s with cane vs. 358 SD 88 mm/s without). In addition, C7 backward acceleration increased by approximately 23% (3.2 SD 0.7 m/s(2) with cane vs. 2.6 SD 0.8 m/s(2) without) and the vertical motion of the right hand decreased (187 SD 98 mm with cane vs. 372 SD 260 mm without). Additionally, no subject was able to use a cane to broaden their base of support. The ability to limit trunk extension is crucial for preventing falls. Therefore, using a cane jeopardizes recovery from backward balance loss. The results encourage further research on the risk of a cane on balance recovery for the elderly population and habitual cane users.

  11. Pattern recognition applied to mineral characterization of Brazilian coffees and sugar-cane spirits

    NASA Astrophysics Data System (ADS)

    Fernandes, Andréa P.; Santos, Mirian C.; Lemos, Sherlan G.; Ferreira, Márcia M. C.; Nogueira, Ana Rita A.; Nóbrega, Joaquim A.

    2005-06-01

    Aluminium, Ca, Cu, Fe, K, Mg, Mn, Na, Pb, S, Se, Si, Sn, Sr, and Zn were determined in coffee and sugar-cane spirit (cachaça) samples by axial viewing inductively coupled plasma optical emission spectrometry (ICP OES). Pattern recognition techniques such as principal component analysis and cluster analysis were applied to data sets in order to characterize samples with relation to their geographical origin and production mode (industrial or homemade and organically or conventionally produced). Attempts to correlate metal ion content with the geographical origin of coffee and the production mode (organic or conventional) of cachaça were not successful. Some differentiation was suggested for the geographical origin of cachaça of three regions (Northeast, Central, and South), and for coffee samples, related to the production mode. Clear separations were only obtained for differentiation between industrial and homemade cachaças, and between instant soluble and roasted coffees.

  12. Composition of sugar cane, energy cane, and sweet sorghum suitable for ethanol production at Louisiana sugar mills.

    PubMed

    Kim, Misook; Day, Donal F

    2011-07-01

    A challenge facing the biofuel industry is to develop an economically viable and sustainable biorefinery. The existing potential biorefineries in Louisiana, raw sugar mills, operate only 3 months of the year. For year-round operation, they must adopt other feedstocks, besides sugar cane, as supplemental feedstocks. Energy cane and sweet sorghum have different harvest times, but can be processed for bio-ethanol using the same equipment. Juice of energy cane contains 9.8% fermentable sugars and that of sweet sorghum, 11.8%. Chemical composition of sugar cane bagasse was determined to be 42% cellulose, 25% hemicellulose, and 20% lignin, and that of energy cane was 43% cellulose, 24% hemicellulose, and 22% lignin. Sweet sorghum was 45% cellulose, 27% hemicellulose, and 21% lignin. Theoretical ethanol yields would be 3,609 kg per ha from sugar cane, 12,938 kg per ha from energy cane, and 5,804 kg per ha from sweet sorghum.

  13. Effect of Cane Length on Drop-Off Detection Performance

    ERIC Educational Resources Information Center

    Kim, Dae Shik; Emerson, Robert Wall

    2012-01-01

    Although individuals who are blind have used a stick or a cane for their independent travel since the early years of human history, designs for modern long canes did not appear until World War II, when the systematic long cane techniques were developed by Hoover (1962). Ergonomic factors, such as the length of the cane, may affect how well a cane…

  14. Spatial relationship between the productivity of cane sugar and soil electrical conductivity measured by electromagnetic induction

    NASA Astrophysics Data System (ADS)

    Siqueira, Glecio; Silva, Jucicléia; Bezerra, Joel; Silva, Enio; Montenegro, Abelardo

    2013-04-01

    The cultivation of sugar cane in Brazil occupies a prominent place in national production chain, because the country is the main world producer of sugar and ethanol. Accordingly, studies are needed that allow an integrated production and technified, and especially that estimates of crops are consistent with the actual production of each region. The objective of this study was to determine the spatial relationship between the productivity of cane sugar and soil electrical conductivity measured by electromagnetic induction. The field experiment was conducted at an agricultural research site located in Goiana municipality, Pernambuco State, north-east of Brazil (Latitude 07 ° 34 '25 "S, Longitude 34 ° 55' 39" W). The surface of the studied field is 6.5 ha, and its mean height 8.5 m a.s.l. This site has been under sugarcane (Saccharum officinarum sp.) monoculture during the last 24 years and it was managed burning the straw each year after harvesting, renewal of plantation was performed every 7 years. Studied the field is located 10 km east from Atlantic Ocean and it is representative of the regional landscape lowlands, whose soils are affected by salinity seawater, sugarcane plantations with the main economical activity. Soil was classified an orthic the Podsol. The productivity of cane sugar and electrical conductivity were measured in 90 sampling points. The productivity of cane sugar was determined in each of the sampling points in plots of 9 m2. The Apparent soil electrical conductivity (ECa, mS m-1) was measured with an electromagnetic induction device EM38-DD (Geonics Limited). The equipment consists of two units of measurement, one in a horizontal dipole (ECa-H) to provide effective measurement distance of 1.5 m approximately and other one in vertical dipole (ECa-V) with an effective measurement depth of approximately 0.75 m. Data were analyzed using descriptive statistics and geostatistical tools. The results showed that productivity in the study area reached values above 200 t ha-1, with higher values of productivity are concentrated in the region northern terrain. The maps of soil electrical conductivity (ECa-V and ECa-H) showed behavior similar to the productivity of cane sugar. The linear correlation showed values of 0.74 (yield x ECa-H) and 0.85 (yield x ECa-V). The adjusted semivariograms showed no similarity in the spatial pattern of pairs of semivariance. The electrical conductivity measured by electromagnetic induction has been shown as an important tool for predicting the productivity of sugar cane, however more studies are needed to determine the magnitude of the differences between such attributes.

  15. Method for producing tip-layered, long-cane blackberry plants using the rotating cross-arm trellis and cane training system

    USDA-ARS?s Scientific Manuscript database

    The rotating cross-arm trellis and a unique cane training technique was used to produce 5- to 6-ft-long tall-cane plants of semi-erect (cv. Triple Crown) and trailing (cv. Siskiyou) blackberries. The primocanes were bent to grow horizontally at 18 in height and the lateral canes that developed on th...

  16. Sugar Cane: A Bitter-Sweet Legacy. A Study of the Disappearing African-American Worker on the Sugar Cane Plantations in Southern Louisiana.

    ERIC Educational Resources Information Center

    Jones, John A., Jr.; And Others

    This resource/study guide is designed to accompany the instructional video, "Sugar Cane: A Bitter-Sweet Legacy," which explores the significance of cultivating, harvesting, and refining sugar cane. It is also a brief study of the disappearing African-American workers on the sugar cane plantations in southern Louisiana. Seven main ideas…

  17. Ethanol from Sugar Cane: Flask Experiments Using the EX-FERM Technique

    PubMed Central

    Rolz, Carlos; de Cabrera, Sheryl

    1980-01-01

    Alcohol production at the laboratory scale from sugar cane pieces by the EX-FERM technique was studied with 37 strains of Saccharomyces spp. The EX-FERM process is novel in that it employs the simultaneous extraction and fermentation of the sucrose in a cane-water suspension. Two types of cane treatments were used: chips and shredded pith, either fresh or dried. A mother culture of the yeast was prepared in enriched cane juice and then added to the cane-water mixture. After static fermentation for 40 h at 30°C, the cane was removed, and fresh cane was added to the yeast-alcohol broth. After an additional 24 h, the cane was again removed and the liquor was analyzed. After the first 40-h cycle, sugar consumption was above 99% with 10 of the 37 yeast strains tested, and ethanol reached levels of 1.29 to 4.00 g per 100 ml, depending on the yeast strain. The final ethanol concentration reached 4.27 to 5.37 g per 100 ml, and sugar consumption was above 98% in three cases during a second EX-FERM cycle employing previously air-dried chips and pith. Product yields were within accepted values. Cane treatment did not appear to affect the results at this level. PMID:16345626

  18. Study of Sugar Cane Management Systems in Brazil Using Laser Induced Fluorescence

    NASA Astrophysics Data System (ADS)

    Cabral, Jader; Villas-Boas, Paulino; Carvalho, Camila; Corá, José Eduardo; Milori, Débora

    2014-05-01

    Brazil is the largest producer of cane sugar, consequently, is a leader in the production of bio-ethanol, a clean and renewable energy that fits the model of sustainable economy as discussed and pursued by our society. Our state of São Paulo concentrates 60% of national production, representing a sizeable share in the range of world production. All this economic potential is closely monitored by the scientific community, which develops numerous studies seeking an improvement in production efficiency and reduced environmental impacts caused by the planting. However, the study of soil samples, in plantation areas, demands results about the content and structural forms of organic matter (OM). Also, the soil carbon stocks depend on the type of management. Our goal is to study OM of soil samples from four sugar cane management systems: (i) unburned cane harvest, (ii) preharvest burned, (iii) addition of sugarcane bagasse ash and (iv) addition of residue from the extraction of sucrose, using Laser Induced Fluorescence Spectroscopy of solid state. All the emission spectra were acquired using the system called LIFS-405, which consists of a diode laser Coherent, model cube with excitation at 405 nm, maximum output power of 50mJ and a mini-spectrometer, Ocean Optics USB2000-high sensitivity, with range of 194-894 nm and a fiber-optic bundle design (six excitation fibers in a circular path and one central fiber the collect the fluorescence). In this work, we will present the preliminary results evolving the humification index (HLIFS) of soil OM and total carbon amount (TC) for the different types of management. HLIFS shows a close correlation with the humification index of humic acid in solution obtained by means 2D conventional fluorescence spectroscopy.

  19. Occurrence and estimation of trans-resveratrol in one-year-old canes from seven major Chinese grape producing regions.

    PubMed

    Zhang, Ang; Fang, Yulin; Li, Xuan; Meng, Jiangfei; Wang, Hua; Li, Hua; Zhang, Zhenwen; Guo, Zhijun

    2011-03-31

    The concentration of trans-resveratrol in 165 grape cane samples from three major grape production regions and four large distribution centers of Chinese wild Vitis species were determined by reversed-phase high-performance liquid chromatography (HPLC). Among the different genotype groups and purpose of uses, cultivars of V. vinifera had much higher amounts of trans-resveratrol than did the cultivars of both V. labrusca or V. labrusca and V. vinifera hybrids, and within the V. vinifera species, significantly higher amounts of trans-resveratrol were found in wine grapes compared to table ones. No significant differences were observed between V. labrusca and its hybrids from crosses with V. vinifera, and between red cultivars and white ones (P < 0.05 or P < 0.01). The contents of trans-resveratrol, as a normal constituent occurring in grape canes, in Chinese wild species of V. amurensis, V. pentagona, and V. davidii from their native habitats were also relatively high.

  20. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

  1. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

  2. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

  3. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

  4. 21 CFR 890.3075 - Cane.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Cane. 890.3075 Section 890.3075 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3075 Cane. (a) Identification. A cane...

  5. 21 CFR 890.3075 - Cane.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Cane. 890.3075 Section 890.3075 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3075 Cane. (a) Identification. A cane...

  6. 21 CFR 890.3075 - Cane.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Cane. 890.3075 Section 890.3075 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3075 Cane. (a) Identification. A cane...

  7. 21 CFR 890.3075 - Cane.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Cane. 890.3075 Section 890.3075 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3075 Cane. (a) Identification. A cane...

  8. 21 CFR 890.3075 - Cane.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cane. 890.3075 Section 890.3075 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3075 Cane. (a) Identification. A cane...

  9. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

  10. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

  11. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

  12. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

  13. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

  14. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

  15. Individual variation and repeatability in urinary corticosterone metabolite responses to capture in the cane toad (Rhinella marina).

    PubMed

    Narayan, Edward J; Molinia, Frank C; Cockrem, John F; Hero, Jean-Marc

    2012-01-15

    Urinary corticosterone metabolite enzyme-immunoassay (EIA) can be used for the non-invasive assessment of baseline levels and corticosterone responses in amphibians. In this study, urinary corticosterone responses of wild male cane toads (Rhinella marina) to confinement and repeated handling were measured to quantify individual variation in corticosterone responses for the first time in an amphibian species. Urine samples were collected at 0 h in the wild, hourly from 2 to 8 h after transfer into captivity, and again at 12 and 24 h in captivity. Toads were then held in captivity and subjected to the same sampling protocol on three occasions at 14 days intervals to quantify variation in corticosterone metabolite responses within and between toads. Baseline and individual corticosterone metabolite responses in male cane toads were generally consistent, with high statistical repeatabilities for 0 h (r=0.630), 6 h (r=0.793), 12 h (r=0.652) and 24 h (r=0.721) corticosterone metabolite concentrations, and for the total and corrected integrated corticosterone responses (r=0.567, p=0.033; r=0.728, p=0.014 respectively). Urinary corticosterone responses appear to be a stable, repeatable trait within individuals. Corticosterone responses in amphibians can be more readily measured when urine rather than plasma samples are collected, and the protocol established in the current study can now be applied to the study of variation in corticosterone responses in other amphibians. Copyright © 2011 Elsevier Inc. All rights reserved.

  16. 40 CFR 409.40 - Applicability; description of the Louisiana raw cane sugar processing subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Louisiana raw cane sugar processing subcategory. 409.40 Section 409.40 Protection of Environment... CATEGORY Louisiana Raw Cane Sugar Processing Subcategory § 409.40 Applicability; description of the Louisiana raw cane sugar processing subcategory. The provisions of this subpart are applicable to discharges...

  17. 40 CFR 409.70 - Applicability; description of the Hawaiian raw cane sugar processing subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Hawaiian raw cane sugar processing subcategory. 409.70 Section 409.70 Protection of Environment... CATEGORY Hawaiian Raw Cane Sugar Processing Subcategory § 409.70 Applicability; description of the Hawaiian raw cane sugar processing subcategory. The provisions of this subpart are applicable to discharges...

  18. 40 CFR 409.70 - Applicability; description of the Hawaiian raw cane sugar processing subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Hawaiian raw cane sugar processing subcategory. 409.70 Section 409.70 Protection of Environment... CATEGORY Hawaiian Raw Cane Sugar Processing Subcategory § 409.70 Applicability; description of the Hawaiian raw cane sugar processing subcategory. The provisions of this subpart are applicable to discharges...

  19. 40 CFR 409.40 - Applicability; description of the Louisiana raw cane sugar processing subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Louisiana raw cane sugar processing subcategory. 409.40 Section 409.40 Protection of Environment... CATEGORY Louisiana Raw Cane Sugar Processing Subcategory § 409.40 Applicability; description of the Louisiana raw cane sugar processing subcategory. The provisions of this subpart are applicable to discharges...

  20. 40 CFR 409.80 - Applicability; description of the Puerto Rican raw cane sugar processing subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Puerto Rican raw cane sugar processing subcategory. 409.80 Section 409.80 Protection of Environment... CATEGORY Puerto Rican Raw Cane Sugar Processing Subcategory § 409.80 Applicability; description of the Puerto Rican raw cane sugar processing subcategory. The provisions of this subpart are applicable to...

  1. 40 CFR 409.80 - Applicability; description of the Puerto Rican raw cane sugar processing subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Puerto Rican raw cane sugar processing subcategory. 409.80 Section 409.80 Protection of Environment... CATEGORY Puerto Rican Raw Cane Sugar Processing Subcategory § 409.80 Applicability; description of the Puerto Rican raw cane sugar processing subcategory. The provisions of this subpart are applicable to...

  2. Celebrating White Cane Awareness Month.

    ERIC Educational Resources Information Center

    Koch, Judy; McGraw, Jane M.

    1995-01-01

    White Cane Awareness Month was created to teach the public that the long cane is a tool for maintaining independence and dignity and a symbol of freedom, not of pity or helplessness. Public relations materials were developed, including a demonstration for television stations on use of the long cane and a quiz to distribute at information booths.…

  3. Differences in the Limits of Stability Between Older Rolling Walker Users and Older Single-Tip-Cane Users - A Preliminary Study.

    PubMed

    Liu, Hao Howe; Quiben, Myles; Holmes, Clayton; Connors, Michael; Salem, Yasser

    To identify the differences in the limits of stability (LOS) between older rolling walker and single-tip-cane users. This was a matched paired t-test design with repeated measure. Eighteen older subjects were matched based on age, gender, and functional level. The subjects were assessed using the multidirectional reach test initially and 5-month later in four directions: forward, backward, leftward, and rightward. Initially, there were no differences between cane users and rolling walker users in the LOS in all directions. However, 5-month later, the cane users who held their canes in their right hand had significantly better stability in forward and rightward reach than the walker users (p < .05). Further, the walker users demonstrated significantly decreased functional reach in forward reach (p < .05). Cane users might have better stability than walker users in the forward direction and in the direction toward the side holding the cane. This study may provide guide for clinicians including nurses for selecting appropriate rehabilitative interventions for older adults using walkers and canes.

  4. The effect of cane use on the compensatory step following posterior perturbations.

    PubMed

    Hall, Courtney D; Jensen, Jody L

    2004-08-01

    The compensatory step is a critical component of the balance response and is impaired in older fallers. The purpose of this research was to examine whether utilization of a cane modified the compensatory step response following external posterior perturbations. Single subject withdrawal design was employed. Single subject statistical analysis--the standard deviation bandwidth-method--supplemented visual analysis of the data. Four older adults (range: 73-83 years) with balance impairment who habitually use a cane completed this study. Subjects received a series of sudden backward pulls that were large enough to elicit compensatory stepping. We examined the following variables both with and without cane use: timing of cane loading relative to step initiation and center of mass acceleration, stability margin, center of mass excursion and velocity, step length and width. No participant loaded the cane prior to initiation of the first compensatory step. There was no effect of cane use on the stability margin, nor was there an effect of cane use on center of mass excursion or velocity, or step length or width. These data suggest that cane use does not necessarily improve balance recovery following an external posterior perturbation when the individual is forced to rely on compensatory stepping. Instead these data suggest that the strongest factor in modifying step characteristics is experience with the perturbation.

  5. 9975 Shipping package component long-term degradation rates

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daugherty, W. L.

    Special nuclear materials are being stored in the K-Area Complex using 3013 containers that are held within Model 9975 shipping packages. The service life for these packages in storage was recently increased from 15 to 20 years, since some of these packages have been stored for nearly 15 years. A strategy is also being developed whereby such storage might be extended beyond 20 years. This strategy is based on recent calculations that support acceptable 9975 package performance for 20 years with internal heat loads up to 19 watts, and identifies a lower heat load limit for which the package componentsmore » should degrade at half the bounding rate or less, thus doubling the effective storage life for these lower wattage packages. The components of the 9975 package that are sensitive to aging under storage conditions are the fiberboard overpack and the O-ring seals, although some degradation of the lead shield and outer drum are also possible. This report summarizes degradation rates applicable to lower heat load storage conditions. In particular, the O-ring seals should provide leak-tight performance for more than 40 years in packages for which their maximum temperature is ≤135 °F. Similarly, the fiberboard should remain acceptable in performance of its required safety functions for up to 40 years in packages with a maximum fiberboard temperature ≤125 °F.« less

  6. Effects of walking with a cane on balance and social participation among community-dwelling post-stroke individuals.

    PubMed

    Hamzat, T K; Kobiri, A

    2008-06-01

    Walking devices such as canes and frames are often prescribed to post-stroke individuals to enhance their balance and walking, and thus facilitate community reintegration and social participation. The aim of this study was to observe social participation and balance in post-stroke hemiparetic patients and compare the performance of those walking with a cane (AD group) and without a cane (WAD group). The relationships between cane usage and activity participation and balance were also studied. In this ex post facto research study, balance and social participation were evaluated using the Berg Balance Scale (BBS) and the Craig Handicap Assessment and Reporting Technique (CHART) in 50 individuals with hemiparesis secondary to first incidence hemispheric stroke. The study included 25 AD subjects (mean age 59.88+/-12.04 years) and 25 WAD subjects (mean age 55.84+/-11.30 years) who were consecutively recruited from the physiotherapy units of Korle Bu Teaching Hospital (KBTH) and the 37 Military Hospital in Accra (Ghana). Before recruitment into the study, both groups of subjects were matched for age, height, weight, BBS and CHART scores at the point of discharge from the inpatient units of the two hospitals, the duration of stroke, and the duration of physiotherapy post-stroke. Mann-Whitney U statistics showed that the AD group had comparatively higher mean participation scores (U=22.37; P=0.00) and lower mean balance performance (BBS score U=30.68; P=0.00) than their WAD counterparts. Spearman's correlation coefficient also revealed a significant negative correlation between the BBS and CHART scores in both groups (AD rho=-0.063; P=0.00 and WAD rho=-0.037; P=0.05). These findings indicate that post-stroke individuals who used a cane to aid in walking had poorer balance and less social participation than their age-matched counterparts who walked unaided. As balance improved (higher BBS score), participation also improved (lower CHART score) in both groups. In spite of the small sample size, the outcome of this study suggests that prescription of a cane for a post-stroke individual should be carefully considered by the physiotherapist, especially if the focus of rehabilitation includes restoration of balance functions and social participation.

  7. Developing capacities in aging studies in the Middle East: Implementation of an Arabic version of the CANE IV among community-dwelling older adults in Lebanon.

    PubMed

    AbiHabib, Laurie E; Chemaitelly, Hiam S; Jaalouk, Lina Y; Karam, Nadim E

    2011-07-01

    To assess the feasibility, reliability, and construct validity of the Camberwell Assessment of Need for the Elderly (CANE) in identifying needs among community-dwelling older adults in South Lebanon with a view towards expanding ageing research in the country. A cross-sectional study was undertaken with 322 individuals, using the CANE, the EQ5d and a socio-demographic questionnaire. Reliability was determined through measuring internal consistency of the CANE. Construct validity was performed through examining CANE inter-item correlations, and comparing correlations with the EQ5d and socio-demographic indicators. A factor analysis was conducted using varimax orthogonal rotation. Cronbach alpha was 0.71. For construct validity, correlations were highest in items measuring needs in looking after the house and food (r = 0.557); company and intimate relationships (r = 0.572); and medication and written/verbal information (r = 0.586). Moderate correlations were found with EQ5d items assessing the same measure, including: EQ5d 'problems taking care of self' and CANE self-care (r = 0.578) and daytime activities (r = 0.523); EQ5d 'problems performing usual activities' and CANE daytime activities (r = 0.553), self-care (r = 0.511) and mobility (r = 0.500); and EQ5d 'problems while walking' and CANE mobility/falls (r = 0.509). Corresponding items of the CANE and EQ-5d were significantly correlated with similar socio-demographic variables. The factor analysis supported results obtained in the CANE inter-item correlations. The Arabic version of the CANE appears acceptable in assessing needs of older adults in South Lebanon. Given that the CANE is an interesting tool that promotes the integration of older persons' perspectives for appropriate interventions, further research is recommended to establish its validity and applicability in other communities in Lebanon and the region.

  8. Capturing the implications of land use change in Brazil through environmental assessment: Time for a strategic approach?

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gallardo, Amarilis Lucia Casteli Figueiredo, E-mail: amacafi@ipt.b; Bond, Alan, E-mail: alan.bond@uea.ac.u

    2011-04-15

    Brazil is experiencing a surge in planting of sugar cane crops driven by internal markets and external policy drivers for biofuels. The current expectation is for the expansion of these crops to continue. This creates concern over the extent to which the full implications of large scale land use change are currently being considered by decision-makers. Using the State of Sao Paulo as a case study (as it accounts for the majority of sugar cane grown in Brazil), a comparison was made of the impacts identified in Environmental Impact Statements (EISs) and Preliminary Environmental Reports (PERs), which have to bemore » submitted for approval of most new sugar cane activities, with significant impacts known to be associated with sugar cane activities derived from literature review. The results from a review of 32 EISs and PERs (30% of the population) indicated that whilst some impacts were well covered by the sample (water and soil pollution, and air emissions) energy balance and Green House Gas emissions and food security had very limited consideration, and water resources, residues, labour conditions and social responsibility were only partially covered. Environmental Impact Assessment is constrained by its environmental advocacy role and its application to the project level only. This study highlights its limitations in the context of assessment of land use change which demands more strategic consideration.« less

  9. CANcer-specific Evaluation System (CANES): a high-accuracy platform, for preclinical single/multi-biomarker discovery

    PubMed Central

    Kwon, Min-Seok; Nam, Seungyoon; Lee, Sungyoung; Ahn, Young Zoo; Chang, Hae Ryung; Kim, Yon Hui; Park, Taesung

    2017-01-01

    The recent creation of enormous, cancer-related “Big Data” public depositories represents a powerful means for understanding tumorigenesis. However, a consistently accurate system for clinically evaluating single/multi-biomarkers remains lacking, and it has been asserted that oft-failed clinical advancement of biomarkers occurs within the very early stages of biomarker assessment. To address these challenges, we developed a clinically testable, web-based tool, CANcer-specific single/multi-biomarker Evaluation System (CANES), to evaluate biomarker effectiveness, across 2,134 whole transcriptome datasets, from 94,147 biological samples (from 18 tumor types). For user-provided single/multi-biomarkers, CANES evaluates the performance of single/multi-biomarker candidates, based on four classification methods, support vector machine, random forest, neural networks, and classification and regression trees. In addition, CANES offers several advantages over earlier analysis tools, including: 1) survival analysis; 2) evaluation of mature miRNAs as markers for user-defined diagnostic or prognostic purposes; and 3) provision of a “pan-cancer” summary view, based on each single marker. We believe that such “landscape” evaluation of single/multi-biomarkers, for diagnostic therapeutic/prognostic decision-making, will be highly valuable for the discovery and “repurposing” of existing biomarkers (and their specific targeted therapies), leading to improved patient therapeutic stratification, a key component of targeted therapy success for the avoidance of therapy resistance. PMID:29050243

  10. 40 CFR 409.50 - Applicability; description of the Florida and Texas raw cane sugar processing subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Florida and Texas raw cane sugar processing subcategory. 409.50 Section 409.50 Protection of Environment... CATEGORY Florida and Texas Raw Cane Sugar Processing Subcategory § 409.50 Applicability; description of the Florida and Texas raw cane sugar processing subcategory. The provisions of this subpart are applicable to...

  11. 40 CFR 409.50 - Applicability; description of the Florida and Texas raw cane sugar processing subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Florida and Texas raw cane sugar processing subcategory. 409.50 Section 409.50 Protection of Environment... CATEGORY Florida and Texas Raw Cane Sugar Processing Subcategory § 409.50 Applicability; description of the Florida and Texas raw cane sugar processing subcategory. The provisions of this subpart are applicable to...

  12. 29 CFR 516.18 - Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 3 2014-07-01 2014-07-01 false Employees employed in certain tobacco, cotton, sugar cane....18 Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are... cigar leaf tobacco, cotton, cottonseed, cotton ginning, sugar cane, sugar processing or sugar beets who...

  13. 29 CFR 516.18 - Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Employees employed in certain tobacco, cotton, sugar cane....18 Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are... cigar leaf tobacco, cotton, cottonseed, cotton ginning, sugar cane, sugar processing or sugar beets who...

  14. 29 CFR 516.18 - Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 3 2013-07-01 2013-07-01 false Employees employed in certain tobacco, cotton, sugar cane....18 Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are... cigar leaf tobacco, cotton, cottonseed, cotton ginning, sugar cane, sugar processing or sugar beets who...

  15. 29 CFR 516.18 - Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 3 2011-07-01 2011-07-01 false Employees employed in certain tobacco, cotton, sugar cane....18 Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are... cigar leaf tobacco, cotton, cottonseed, cotton ginning, sugar cane, sugar processing or sugar beets who...

  16. 29 CFR 516.18 - Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 3 2012-07-01 2012-07-01 false Employees employed in certain tobacco, cotton, sugar cane....18 Employees employed in certain tobacco, cotton, sugar cane or sugar beet services, who are... cigar leaf tobacco, cotton, cottonseed, cotton ginning, sugar cane, sugar processing or sugar beets who...

  17. An experimental study on target recognition using white canes.

    PubMed

    Nunokawa, Kiyohiko; Ino, Shuichi

    2010-01-01

    To understand basic tactile perception using white canes, we compared tapping (two times) and pushing (two times) methods using the index finger and using a white cane, with and without accompanying auditory information. Participants were six visually impaired individuals who used a white cane to walk independently in their daily lives. For each of the tapping and pushing and sound or no sound conditions, participants gave magnitude estimates for the hardness of rubber panels. Results indicated that using a white cane produces sensitivity levels equal to using a finger when accompanied by auditory information, and suggested that when using a white cane to estimate the hardness of a target, it is most effective to have two different modalities of tactile and auditory information derived from tapping.

  18. Judging hardness of an object from the sounds of tapping created by a white cane.

    PubMed

    Nunokawa, K; Seki, Y; Ino, S; Doi, K

    2014-01-01

    The white cane plays a vital role in the independent mobility support of the visually impaired. Allowing the recognition of target attributes through the contact of a white cane is an important function. We have conducted research to obtain fundamental knowledge concerning the exploration methods used to perceive the hardness of an object through contact with a white cane. This research has allowed us to examine methods that enhance accuracy in the perception of objects as well as the materials and structures of a white cane. Previous research suggest considering the roles of both auditory and tactile information from the white cane in determining objects' hardness is necessary. This experimental study examined the ability of people to perceive the hardness of an object solely through the tapping sounds of a white cane (i.e., auditory information) using a method of magnitude estimation. Two types of sounds were used to estimate hardness: 1) the playback of recorded tapping sounds and 2) the sounds produced on-site by tapping. Three types of handgrips were used to create different sounds of tapping on an object with a cane. The participants of this experiment were five sighted university students wearing eye masks and two totally blind students who walk independently with a white cane. The results showed that both sighted university students and totally blind participants were able to accurately judge the hardness of an object solely by using auditory information from a white cane. For the blind participants, different handgrips significantly influenced the accuracy of their estimation of an object's hardness.

  19. Predicting Greenhouse Gas Emissions and Soil Carbon from Changing Pasture to an Energy Crop

    PubMed Central

    Duval, Benjamin D.; Anderson-Teixeira, Kristina J.; Davis, Sarah C.; Keogh, Cindy; Long, Stephen P.; Parton, William J.; DeLucia, Evan H.

    2013-01-01

    Bioenergy related land use change would likely alter biogeochemical cycles and global greenhouse gas budgets. Energy cane (Saccharum officinarum L.) is a sugarcane variety and an emerging biofuel feedstock for cellulosic bio-ethanol production. It has potential for high yields and can be grown on marginal land, which minimizes competition with grain and vegetable production. The DayCent biogeochemical model was parameterized to infer potential yields of energy cane and how changing land from grazed pasture to energy cane would affect greenhouse gas (CO2, CH4 and N2O) fluxes and soil C pools. The model was used to simulate energy cane production on two soil types in central Florida, nutrient poor Spodosols and organic Histosols. Energy cane was productive on both soil types (yielding 46–76 Mg dry mass⋅ha−1). Yields were maintained through three annual cropping cycles on Histosols but declined with each harvest on Spodosols. Overall, converting pasture to energy cane created a sink for GHGs on Spodosols and reduced the size of the GHG source on Histosols. This change was driven on both soil types by eliminating CH4 emissions from cattle and by the large increase in C uptake by greater biomass production in energy cane relative to pasture. However, the change from pasture to energy cane caused Histosols to lose 4493 g CO2 eq⋅m−2 over 15 years of energy cane production. Cultivation of energy cane on former pasture on Spodosol soils in the southeast US has the potential for high biomass yield and the mitigation of GHG emissions. PMID:23991028

  20. Retention efficiency of Cd, Pb and Zn from agricultural by-products activated carbon and biochar under laboratory conditions

    NASA Astrophysics Data System (ADS)

    Coscione, Aline; Ramos, Barbara

    2015-04-01

    The immobilization of inorganic contaminants by using biochar in soils has played an increasingly important role and it is seen as an attractive alternative for the remediation of heavy metals. Although, the production of activated carbon (CA) from agricultural by-products has received special attention, the activation of the the organic source has been studied in order to increase its porposity, surface area and chemical polarity, resulting in higher adsorption of metals. Therefore, this study aimed to evaluate the effectiveness of BC and CA samples, obtained from a eucalyptus husks and cane sugar bagasse after activation with 20% phosphoric acid and pyrolyzed at 450oC in the retention of Zn, Cd and Pb using contaminated individual solutions. The experiment was performed using samples of activated carbon of eucalyptus husk (CCA), eucalyptus husk biochar (BC), activated carbon of sugar cane bagasse (CBA) and sugar cane bagasse biochar (BB) previously treated with Zn, Cd (range of tested solution from 0.1 up to 12 mmol L-1) and Pb (from 0.1 up 50 mmol L-1) which were submitted to stirring with ammonium acetate solution at pH 4.9 for 48 h. The results obtained were adjusted with Langmuir desorptiom isotherms. The pH of the resulting solution, were the meatls were analyse, was measure and remained in the range 4.9 - 5.0. The lower pH found in activated samples (range 2.4-2.5) resulted in larger desorption of metals than the biochar samples (pH of 9.7 for BC and 7.0 for BB). This result is surprising since for the biochar samples it was expected that any precipated metals were dissolved by the desorption solution in addition to metals released by ion exchange. Although the desorption results of activated samoels is still unclear, hich we belive may be explaibed by some adicitonal insterumental analysis, biochar samples showed better potential for application in contaminated soils than the previous.

  1. 75 FR 26316 - Allocation of Additional Fiscal Year (FY) 2010 In-Quota Volume for Raw Cane Sugar

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-11

    ...-Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar. DATES: Effective Date: May 11, 2010. ADDRESSES: Inquiries may be mailed... (HTS), the United States maintains TRQs for imports of raw cane and refined sugar. Section 404(d)(3) of...

  2. 77 FR 57180 - Fiscal Year 2013 Tariff-rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-17

    ... OFFICE OF THE TRADE REPRESENTATIVE Fiscal Year 2013 Tariff-rate Quota Allocations for Raw Cane... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar, and sugar... imports of raw cane sugar and refined sugar. Pursuant to Additional U.S. Note 8 to Chapter 17 of the HTS...

  3. 76 FR 21418 - Fiscal Year 2011 Allocation of Additional Tariff-Rate Quota Volume for Raw Cane Sugar and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-15

    ...-Rate Quota Volume for Raw Cane Sugar and Reallocation of Unused Fiscal Year 2011 Tariff-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar and of country-by-country reallocations of the FY 2011 in-quota quantity...

  4. 40 CFR 409.60 - Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane sugar...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-Hamakua Coast of the Island of Hawaii raw cane sugar processing subcategory. 409.60 Section 409.60... PROCESSING POINT SOURCE CATEGORY Hilo-Hamakua Coast of the Island of Hawaii Raw Cane Sugar Processing Subcategory § 409.60 Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane...

  5. 77 FR 25012 - Fiscal Year 2012 Allocation of Additional Tariff-Rate Quota Volume for Raw Cane Sugar and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-26

    ...-Rate Quota Volume for Raw Cane Sugar and Reallocation of Unused Fiscal Year 2012 Tariff-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar and of country-by-country reallocations of the FY 2012 in-quota quantity...

  6. 40 CFR 409.60 - Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane sugar...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-Hamakua Coast of the Island of Hawaii raw cane sugar processing subcategory. 409.60 Section 409.60... PROCESSING POINT SOURCE CATEGORY Hilo-Hamakua Coast of the Island of Hawaii Raw Cane Sugar Processing Subcategory § 409.60 Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane...

  7. 76 FR 50285 - Fiscal Year 2012 Tariff-Rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-12

    ... for Raw Cane Sugar, Refined and Specialty Sugar and Sugar-Containing Products AGENCY: Office of the... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar and sugar...), the United States maintains tariff-rate quotas (TRQs) for imports of raw cane sugar and refined sugar...

  8. 75 FR 14479 - Reallocation of Unused Fiscal Year 2010 Tariff-Rate Quota Volume for Raw Cane Sugar

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-25

    ...-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION... (TRQ) for imported raw cane sugar. DATES: Effective Date: March 25, 2010. ADDRESSES: Inquiries may be... (HTS), the United States maintains TRQs for imports of raw cane and refined sugar. Section 404(d)(3) of...

  9. 78 FR 57445 - Fiscal Year 2014 WTO Tariff-Rate Quota Allocations for Raw Cane Sugar, Refined and Specialty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-18

    ... Allocations for Raw Cane Sugar, Refined and Specialty Sugar, and Sugar-Containing Products AGENCY: Office of..., 2013, through Sept. 30, 2014) in-quota quantity of the tariff-rate quotas (TRQs) for imported raw cane...), the United States maintains TRQs for imports of raw cane sugar and refined sugar (syrups and molasses...

  10. Analysis of user characteristics related to drop-off detection with long cane

    PubMed Central

    Kim, Dae Shik; Emerson, Robert Wall; Curtis, Amy

    2010-01-01

    This study examined how user characteristics affect drop-off detection with the long cane. A mixed-measures design with block randomization was used for the study, in which 32 visually impaired adults attempted to detect the drop-offs using different cane techniques. Younger cane users detected drop-offs significantly more reliably (mean +/− standard deviation = 74.2% +/− 11.2% of the time) than older cane users (60.9% +/− 10.8%), p = 0.009. The drop-off detection threshold of the younger participants (5.2 +/− 2.1 cm) was also statistically significantly smaller than that of the older participants (7.9 +/− 2.2 cm), p = 0.007. Those with early-onset visual impairment (78.0% +/− 9.0%) also detected drop-offs significantly more reliably than those with later-onset visual impairment (67.3% +/− 12.4%), p = 0.01. No interaction occurred between examined user characteristics (age and age at onset of visual impairment) and the type of cane technique used in drop-off detection. The findings of the study may help orientation and mobility specialists select appropriate cane techniques in accordance with the cane user’s age and onset of visual impairment. PMID:20665349

  11. The "EyeCane", a new electronic travel aid for the blind: Technology, behavior & swift learning.

    PubMed

    Maidenbaum, Shachar; Hanassy, Shlomi; Abboud, Sami; Buchs, Galit; Chebat, Daniel-Robert; Levy-Tzedek, Shelly; Amedi, Amir

    2014-01-01

    Independent mobility is one of the most pressing problems facing people who are blind. We present the EyeCane, a new mobility aid aimed at increasing perception of environment beyond what is provided by the traditional White Cane for tasks such as distance estimation, navigation and obstacle detection. The "EyeCane" enhances the traditional White Cane by using tactile and auditory output to increase detectable distance and angles. It circumvents the technical pitfalls of other devices, such as weight, short battery life, complex interface schemes, and slow learning curve. It implements multiple beams to enables detection of obstacles at different heights, and narrow beams to provide active sensing that can potentially increase the user's spatial perception of the environment. Participants were tasked with using the EyeCane for several basic tasks with minimal training. Blind and blindfolded-sighted participants were able to use the EyeCane successfully for distance estimation, simple navigation and simple obstacle detection after only several minutes of training. These results demonstrate the EyeCane's potential for mobility rehabilitation. The short training time is especially important since available mobility training resources are limited, not always available, and can be quite expensive and/or entail long waiting periods.

  12. Development of the navigation system for the visually impaired by using white cane.

    PubMed

    Hirahara, Yoshiaki; Sakurai, Yusuke; Shiidu, Yuriko; Yanashima, Kenji; Magatani, Kazushige

    2006-01-01

    A white cane is a typical support instrument for the visually impaired. They use a white cane for the detection of obstacles while walking. So, the area where they have a mental map, they can walk using white cane without help of others. However, they cannot walk independently in the unknown area, even if they use a white cane. Because, a white cane is a detecting device for obstacles and not a navigation device for there correcting route. Now, we are developing the navigation system for the visually impaired which uses indoor space. In Japan, sometimes colored guide lines to the destination are used for a normal person. These lines are attached on the floor, we can reach the destination, if we walk along one of these line. In our system, a developed new white cane senses one colored guide line, and makes notice to a user by vibration. This system recognizes the color of the line stuck on the floor by the optical sensor attached in the white cane. And in order to guide still more smoothly, infrared beacons (optical beacon), which can perform voice guidance, are also used.

  13. Effects of cane length and diameter and judgment type on the constant error ratio for estimated height in blindfolded, visually impaired, and sighted participants.

    PubMed

    Huang, Kuo-Chen; Leung, Cherng-Yee; Wang, Hsiu-Feng

    2010-04-01

    The purpose of this study was to assess the ability of blindfolded, visually impaired, and sighted individuals to estimate object height as a function of cane length, cane diameter, and judgment type. 48 undergraduate students (ages 20 to 23 years) were recruited to participate in the study. Participants were divided into low-vision, severely myopic, and normal-vision groups. Five stimulus heights were explored with three cane lengths, varying cane diameters, and judgment types. The participants were asked to estimate the stimulus height with or without reference to a standard block. Results showed that the constant error ratio for estimated height improved with decreasing cane length and comparative judgment. The findings were unclear regarding the effect of cane length on haptic perception of height. Implications were discussed for designing environments, such as stair heights, chairs, the magnitude of apertures, etc., for visually impaired individuals.

  14. 49 CFR 173.308 - Lighters.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., must be capable of withstanding, without leakage or rupture, an internal pressure of at least two times... plastic tray, a plastic, fiberboard or paperboard partition must be used to prevent friction between the...

  15. 49 CFR 173.308 - Lighters.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., must be capable of withstanding, without leakage or rupture, an internal pressure of at least two times... plastic tray, a plastic, fiberboard or paperboard partition must be used to prevent friction between the...

  16. 75 FR 50796 - Fiscal Year 2011 Tariff-Rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-17

    ... for Raw Cane Sugar, Refined and Specialty Sugar, and Sugar-Containing Products AGENCY: Office of the... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar, and sugar... imports of raw cane sugar and refined sugar. Pursuant to Additional U.S. Note 8 to Chapter 17 of the HTS...

  17. 76 FR 42160 - Allocation of Additional Fiscal Year (FY) 2011 In-Quota Volume for Raw Cane Sugar

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-18

    ...-Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar. USTR is also reallocating a portion of the unused original FY 2011 TRQ... imports of raw cane and refined sugar. Section 404(d)(3) of the Uruguay Round Agreements Act (19 U.S.C...

  18. CO2 co-gasification of lower sulphur petroleum coke and sugar cane bagasse via TG-FTIR analysis technique.

    PubMed

    Edreis, Elbager M A; Luo, Guangqian; Li, Aijun; Chao, Chen; Hu, Hongyun; Zhang, Sen; Gui, Ben; Xiao, Li; Xu, Kai; Zhang, Pingan; Yao, Hong

    2013-05-01

    This study investigates the non-isothermal mechanism and kinetic behaviour of gasification of a lower sulphur petroleum coke, sugar cane bagasse and blends under carbon dioxide atmosphere conditions using the thermogravimetric analyser (TGA). The gas products were measured online with coupled Fourier transform infrared spectroscopy (FTIR). The achieved results explored that the sugar cane bagasse and blend gasification happened in two steps: at (<500 °C) the volatiles are released, and at (>700 °C) char gasification occurred, whereas the lower sulphur petroleum coke presented only one char gasification stage at (>800 °C). Significant interactions were observed in the whole process. Some solid-state mechanisms were studied by the Coats-Redfern method in order to observe the mechanisms responsible for the gasification of samples. The results show that the chemical first order reaction is the best responsible mechanism for whole process. The main released gases are CO2, CO, CH4, HCOOH, C6H5OH and CH3COOH. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. 21 CFR 168.130 - Cane sirup.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... § 168.130 Cane sirup. (a) Cane sirup is the liquid food derived by concentration and heat treatment of the juice of sugarcane (Saccharum officinarum L.) or by solution in water of sugarcane concrete made...

  20. 21 CFR 168.130 - Cane sirup.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... § 168.130 Cane sirup. (a) Cane sirup is the liquid food derived by concentration and heat treatment of the juice of sugarcane (Saccharum officinarum L.) or by solution in water of sugarcane concrete made...

  1. 21 CFR 168.130 - Cane sirup.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... § 168.130 Cane sirup. (a) Cane sirup is the liquid food derived by concentration and heat treatment of the juice of sugarcane (Saccharum officinarum L.) or by solution in water of sugarcane concrete made...

  2. 21 CFR 168.130 - Cane sirup.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... § 168.130 Cane sirup. (a) Cane sirup is the liquid food derived by concentration and heat treatment of the juice of sugarcane (Saccharum officinarum L.) or by solution in water of sugarcane concrete made...

  3. 21 CFR 168.130 - Cane sirup.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... § 168.130 Cane sirup. (a) Cane sirup is the liquid food derived by concentration and heat treatment of the juice of sugarcane (Saccharum officinarum L.) or by solution in water of sugarcane concrete made...

  4. Arundinaria gigantea (Walt.) Muhl.

    Treesearch

    Kristina Connor

    2004-01-01

    Giant cane, also known as cane or switchcane, is a perennial monocot, a woody grass, and one of only two native bamboos. With its stem-like rhizomes and hard, ‘woody’ stems, giant cane can grow to a height of 8 to 9 m but is typically less. Giant cane is found at elevations ranging from sea level in southern floodplains to 610 m elevation in the Appalachian Mountains...

  5. Haptic cues for orientation and postural control in sighted and blind individuals

    NASA Technical Reports Server (NTRS)

    Jeka, J. J.; Easton, R. D.; Bentzen, B. L.; Lackner, J. R.

    1996-01-01

    Haptic cues from fingertip contact with a stable surface attenuate body sway in subjects even when the contact forces are too small to provide physical support of the body. We investigated how haptic cues derived from contact of a cane with a stationary surface at low force levels aids postural control in sighted and congenitally blind individuals. Five sighted (eyes closed) and five congenitally blind subjects maintained a tandem Romberg stance in five conditions: (1) no cane; (2,3) touch contact (< 2 N of applied force) while holding the cane in a vertical or slanted orientation; and (4,5) force contact (as much force as desired) in the vertical and slanted orientations. Touch contact of a cane at force levels below those necessary to provide significant physical stabilization was as effective as force contact in reducing postural sway in all subjects, compared to the no-cane condition. A slanted cane was far more effective in reducing postural sway than was a perpendicular cane. Cane use also decreased head displacement of sighted subjects far more than that of blind subjects. These results suggest that head movement control is linked to postural control through gaze stabilization reflexes in sighted subjects; such reflexes are absent in congenitally blind individuals and may account for their higher levels of head displacement.

  6. Contamination of commercial cane sugars by some organic acids and some inorganic anions.

    PubMed

    Wojtczak, Maciej; Antczak, Aneta; Lisik, Krystyna

    2013-01-01

    The aim of the paper was the identification and the quantitative evaluation of the following inorganic anions: chloride, phosphate, nitrate, nitrite, sulphate and the following organic acids: lactic, acetic, formic, malic and citric in commercial "unrefined" brown cane sugars and in cane raw sugars. The determination was carried out by high performance anion exchange chromatography with conductivity detector HPAEC-CD. The conducted analyses have shown that the content of some inorganic anions and organic acids in cane sugars may be an important criterion of the quality of commercial "unrefined" brown cane sugars. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Effect of Thermal Treatment of Fast Growing Wood Fibers on Physical and Mechanical Properties of Light Medium Density Fiberboard

    NASA Astrophysics Data System (ADS)

    Jarusombuti, Songklod; Ayrilmis, Nadir; Fueangvivat, Vallayuth; Bauchongkol, Piyawade

    2011-06-01

    This study investigated physical and mechanical properties of the light medium density fiberboard (MDF) panels made from thermally treated wood fibers of eucalyptus camaldulensis at three different temperatures (393 K, 423 K or 453 K) for 30 or 60 min in a laboratory autoclave. The average thickness swelling of the panels decreased by 16-54% depending on the treatment temperature and time. However, the modulus of rupture, modulus of elasticity, and internal bond strength decreased by 16-37%, 9-25% and 10-39%, respectively. Based on the findings obtained from the present study, it may be said that wood fibers of E. camaldulensis treated at 453 K - 30 min can be used in the light MDF manufacture for use in humid conditions, such as kitchen and bathroom furniture requiring improved dimensional stability.

  8. Development of the navigation system for visually impaired.

    PubMed

    Harada, Tetsuya; Kaneko, Yuki; Hirahara, Yoshiaki; Yanashima, Kenji; Magatani, Kazushige

    2004-01-01

    A white cane is a typical support instrument for the visually impaired. They use a white cane for the detection of obstacles while walking. So, the area where they have a mental map, they can walk using white cane without the help of others. However, they cannot walk independently in the unknown area, even if they use a white cane. Because, a white cane is a detecting device for obstacles and not a navigation device for their correct route. Now, we are developing the navigation system for the visually impaired which uses indoor space. In Japan, sometimes colored guide lines to the destination is used for a normal person. These lines are attached on the floor, we can reach the destination, if we walk along one of these line. In our system, a developed new white cane senses one colored guide line, and make notice to an user by vibration. This system recognizes the line of the color stuck on the floor by the optical sensor attached in the white cane. And in order to guide still more smoothly, infrared beacons (optical beacon), which can perform voice guidance, are also used.

  9. Vinasse application to sugar cane fields. Effect on the unsaturated zone and groundwater at Valle del Cauca (Colombia).

    PubMed

    Ortegón, Gloria Páez; Arboleda, Fernando Muñoz; Candela, Lucila; Tamoh, Karim; Valdes-Abellan, Javier

    2016-01-01

    Extensive application of vinasse, a subproduct from sugar cane plantations for bioethanol production, is currently taking place as a source of nutrients that forms part of agricultural management in different agroclimatic regions. Liquid vinasse composition is characterised by high variability of organic compounds and major ions, acid pH (4.7), high TDS concentration (117,416-599,400mgL(-1)) and elevated EC (14,350-64,099μScm(-1)). A large-scale sugar cane field application is taking place in Valle del Cauca (Colombia), where monitoring of soil, unsaturated zone and the aquifer underneath has been made since 2006 to evaluate possible impacts on three experimental plots. For this assessment, monitoring wells and piezometers were installed to determine groundwater flow and water samples were collected for chemical analysis. In the unsaturated zone, tensiometers were installed at different depths to determine flow patterns, while suction lysimeters were used for water sample chemical determinations. The findings show that in the sandy loam plot (Hacienda Real), the unsaturated zone is characterised by low water retention, showing a high transport capacity, while the other two plots of silty composition presented temporal saturation due to La Niña event (2010-2011). The strong La Niña effect on aquifer recharge which would dilute the infiltrated water during the monitoring period and, on the other hand dissolution of possible precipitated salts bringing them back into solution may occur. A slight increase in the concentration of major ions was observed in groundwater (~5% of TDS), which can be attributed to a combination of factors: vinasse dilution produced by water input and hydrochemical processes along with nutrient removal produced by sugar cane uptake. This fact may make the aquifer vulnerable to contamination. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Mobility Aids

    MedlinePlus

    ... or have an injury. They include Crutches Canes Walkers Wheelchairs Motorized scooters You may need a walker or cane if you are at risk of ... You should be fitted for crutches, canes and walkers. If they fit, these devices give you support, ...

  11. Older homebound women: negotiating reliance on a cane or walker.

    PubMed

    Porter, Eileen J; Benson, Jacquelyn J; Matsuda, Sandy

    2011-04-01

    Canes and walkers are commonly characterized as assistive devices that serve the same purpose: as walking aides. These general views were reappraised and tempered in this descriptive phenomenological study with 40 older women (aged 85 to 98 years) who were unable to leave their homes without help. The purpose was to describe the phenomena of negotiating reliance on canes and walkers as walking devices and the lifeworld context underlying each phenomenon. Relative to lifeworld, there were differences between coming to terms with using a cane and coming to terms with using a walker. Data revealed similarities and distinctions between the basic intentions of relying on canes and walkers and the associated purposes served by canes and walkers. Participants did not view either device as consistently assistive. Findings evoke opportunities for dialogue among older persons, scholars, practitioners, and designers of these devices about coming to terms with such devices and relying on them.

  12. Older Homebound Women: Negotiating Reliance on a Cane or Walker

    PubMed Central

    Porter, Eileen J.; Benson, Jacquelyn J.; Matsuda, Sandy

    2012-01-01

    Canes and walkers are commonly characterized as assistive devices and as devices that serve the same purpose, as walking aides. These general views were reappraised and tempered in this descriptive phenomenological study with 40 older women (aged 85-98) who were unable to leave their homes without help. The purpose was to describe the phenomena of negotiating reliance on canes and walkers as walking devices and the lifeworld context underlying each phenomenon. Relative to lifeworld, there were differences between coming to terms with using a cane and coming to terms with using a walker. Data revealed similarities and distinctions between the basic intentions of relying on canes and on walkers and the associated purposes served by canes and walkers. Participants did not view either device as consistently assistive. Findings evoke opportunities for dialogue among older persons, scholars, practitioners, and designers of these devices about coming to terms with such devices and relying on them. PMID:21041520

  13. 40 CFR 63.4681 - Am I subject to this subpart?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... application of clay slurry, titanium dioxide, or asphalt coatings to fiberboard. (v) Painting of company logo...) Synthetic patches, wood patches, and wood putty applied to plywood. (ix) Application of concrete forming and...

  14. Using a cane

    MedlinePlus

    ... with a cane. Stepping Up or Down a Step or Curb To go up one step or a curb: Step up with your stronger leg first. Place your ... to help your balance. To go down one step or a curb: Set your cane down below ...

  15. A Cane Improves Postural Recovery From an Unpracticed Slip During Walking in People With Parkinson Disease

    PubMed Central

    Saengsirisuwan, Vitoon; Carlson-Kuhta, Patricia; Horak, Fay B.

    2012-01-01

    Background Little is known about the effects of use of a cane on balance during perturbed gait or whether people with Parkinson disease (PD) benefit from using a cane. Objectives The purpose of this study was to evaluate the effects of cane use on postural recovery from a slip due to repeated surface perturbations in individuals with PD compared with age- and sex-matched individuals who were healthy. Design This was a prospective study with 2 groups of participants. Methods Fourteen individuals with PD (PD group) and 11 individuals without PD (control group) walked across a platform that translated 15 cm rightward at 30 cm/s during the single-limb support phase of the right foot. Data from 15 trials in 2 conditions (ie, with and without an instrumented cane in the right hand) were collected in random order. Outcome measures included lateral displacement of body center of mass (COM) due to the slip and compensatory step width and length after the perturbation. Results Cane use improved postural recovery from the first untrained slip, characterized by smaller lateral COM displacement, in the PD group but not in the control group. The beneficial effect of cane use, however, occurred only during the first perturbation, and those individuals in the PD group who demonstrated the largest COM displacement without a cane benefited the most from use of a cane. Both PD and control groups gradually decreased lateral COM displacement across slip exposures, but a slower learning rate was evident in the PD group participants, who required 6, rather than 3, trials for adapting balance recovery. Limitations Future studies are needed to examine the long-term effects of repeated slip training in people with PD. Conclusions Use of a cane improved postural recovery from an unpracticed slip in individuals with PD. Balance in people with PD can be improved by training with repeated exposures to perturbations. PMID:22628583

  16. A cane improves postural recovery from an unpracticed slip during walking in people with Parkinson disease.

    PubMed

    Boonsinsukh, Rumpa; Saengsirisuwan, Vitoon; Carlson-Kuhta, Patricia; Horak, Fay B

    2012-09-01

    Little is known about the effects of use of a cane on balance during perturbed gait or whether people with Parkinson disease (PD) benefit from using a cane. The purpose of this study was to evaluate the effects of cane use on postural recovery from a slip due to repeated surface perturbations in individuals with PD compared with age- and sex-matched individuals who were healthy. This was a prospective study with 2 groups of participants. Fourteen individuals with PD (PD group) and 11 individuals without PD (control group) walked across a platform that translated 15 cm rightward at 30 cm/s during the single-limb support phase of the right foot. Data from 15 trials in 2 conditions (ie, with and without an instrumented cane in the right hand) were collected in random order. Outcome measures included lateral displacement of body center of mass (COM) due to the slip and compensatory step width and length after the perturbation. Cane use improved postural recovery from the first untrained slip, characterized by smaller lateral COM displacement, in the PD group but not in the control group. The beneficial effect of cane use, however, occurred only during the first perturbation, and those individuals in the PD group who demonstrated the largest COM displacement without a cane benefited the most from use of a cane. Both PD and control groups gradually decreased lateral COM displacement across slip exposures, but a slower learning rate was evident in the PD group participants, who required 6, rather than 3, trials for adapting balance recovery. Future studies are needed to examine the long-term effects of repeated slip training in people with PD. Use of a cane improved postural recovery from an unpracticed slip in individuals with PD. Balance in people with PD can be improved by training with repeated exposures to perturbations.

  17. Two dominant loci determine resistance to Phomopsis cane lesions in F1 families of hybrid grapevines.

    PubMed

    Barba, Paola; Lillis, Jacquelyn; Luce, R Stephen; Travadon, Renaud; Osier, Michael; Baumgartner, Kendra; Wilcox, Wayne F; Reisch, Bruce I; Cadle-Davidson, Lance

    2018-05-01

    Rapid characterization of novel NB-LRR-associated resistance to Phomopsis cane spot on grapevine using high-throughput sampling and low-coverage sequencing for genotyping, locus mapping and transcriptome analysis provides insights into genetic resistance to a hemibiotrophic fungus. Phomopsis cane and leaf spot, caused by the hemibiotrophic fungus Diaporthe ampelina (syn = Phomopsis viticola), reduces the productivity in grapevines. Host resistance was studied on three F 1 families derived from crosses involving resistant genotypes 'Horizon', Illinois 547-1, Vitis cinerea B9 and V. vinifera 'Chardonnay'. All families had progeny with extremely susceptible phenotypes, developing lesions on both dormant canes and maturing fruit clusters. Segregation of symptoms was observed under natural levels of inoculum in the field, while phenotypes on green shoots were confirmed under controlled inoculations in greenhouse. High-density genetic maps were used to localize novel qualitative resistance loci named Rda1 and Rda2 from V. cinerea B9 and 'Horizon', respectively. Co-linearity between reference genetic and physical maps allowed localization of Rda2 locus between 1.5 and 2.4 Mbp on chromosome 7, and Rda1 locus between 19.3 and 19.6 Mbp of chromosome 15, which spans a cluster of five NB-LRR genes. Further dissection of this locus was obtained by QTL mapping of gene expression values 14 h after inoculation across a subset of the 'Chardonnay' × V. cinerea B9 progeny. This provided evidence for the association between transcript levels of two of these NB-LRR genes with Rda1, with increased NB-LRR expression among susceptible progeny. In resistant parent V. cinerea B9, inoculation with D. ampelina was characterized by up-regulation of SA-associated genes and down-regulation of ethylene pathways, suggesting an R-gene-mediated response. With dominant effects associated with disease-free berries and minimal symptoms on canes, Rda1 and Rda2 are promising loci for grapevine genetic improvement.

  18. Distribution of Dekkera bruxellensis in a sugarcane-based fuel ethanol fermentation plant.

    PubMed

    da Silva, T C D; Leite, F C B; De Morais, M A

    2016-04-01

    We investigated the presence of the yeast Dekkera bruxellensis in samples collected at three points surrounding the industrial alcoholic fermentation plants of two distilleries where there are often cases of contamination caused by this yeast: this involved sugar cane wash water, feeding sugar cane juice and vinasse from the treatment pond. Total yeast was isolated in WLN medium with bromocresol green and cycloheximide and further selected on the basis of its ability to grow in synthetic medium containing nitrate. Following this, colonies were selected from the distribution on nitrate plates and identified by amplification with species-specific primers and DNA sequencing of the 26S-D1/D2 locus. The results showed that D. bruxellensis is introduced through the feeding substrate, which suggests that its cells originated with the harvested cane. Subsequently, its population circulates as a result of the reuse of water for washing the cane, in a continuous re-inoculation of the plant with yeasts. Furthermore, the yeast population is formed in the vinasse by the addition of wash water into the treatment ponds and then reintroduced to the culture fields by fertigation, so that the process can be renewed in the following season. It is now possible to adopt sanitation procedures that can prevent the entry of the contamination to the fermentation process. The presence of the yeast Dekkera bruxellensis is sometimes attributed to a decline in the industrial productivity of ethanol since it has a more limited fermentation capacity than Saccharomyces cerevisiae. Although its adaptability to the industrial environment has been noted, so far, there has been no evidence to determine the source of this contamination. In this study, we provide evidence to show that D. bruxellensis comes from the fields together with the harvested cane and is then accumulated and recirculated. It might be possible to prevent the accumulation of this yeast by carrying out sanitation controls during the harvesting season. © 2016 The Society for Applied Microbiology.

  19. Analysis of Calorific Value of Tibarau Cane Briquette

    NASA Astrophysics Data System (ADS)

    Nurdin, H.; Hasanuddin, H.; Darmawi, D.; Prasetya, F.

    2018-04-01

    The development of product diversification through tibarau cane briquettes as an effort in obtaining alternative fuels. Tibarau cane is one of the potential materials of renewable energy sources that can be processed into briquette. So as to reduce dependence on energy fuel oil, which for the middle to lower class is the main requirement. Efforts and innovations tibarau cane briquettes in producing fuel that has quality and performance can be measured with calorific value. Prior to development of this potential required the existence of test and evaluation stages according to the order of the flow of new material product development. Through process technology of briquette product making with compaction and optimization of composition content on tapioca adhesive and mesh particles suitable to get optimum calorific value. The results obtained in this research are the development of tibarau cane briquette model which is recommended as replacement fuel. Where the calorific value of tibarau cane briquette is 11.221,72 kJ / kg at composition percentage 80: 20 and its density is 0,565 gr/cm3. The comparison of mass tibarau with tapioca, particle size, pressure force (compaction), can affect the calorific value and density of tibarau cane briquette.

  20. Sugar cane fiber geotextiles : production, evaluation, and field study : technical summary.

    DOT National Transportation Integrated Search

    1996-08-01

    The sugar cane fiber geotexiles performed as well as the commercial products and exhibited grass propagation and slope protection equivalent to other products. Sugar cane fiber mats were superior in conformation to the slope even after heavy rains. B...

  1. 78 FR 3967 - Notice of Application for Special Permits

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-17

    ...). transportation in Branchburg, NJ. commerce of PG II corrosive materials described as Potassium Hydroxide Solution, UN 1814 and Sodium Hydroxide Solution, UN 1824 in a UN 50G Fiberboard Large Packaging. (modes 1, 2, 3...

  2. 14. LIVING ROOM INTERIOR SHOWING WEST SIDE AND SOUTH END ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. LIVING ROOM INTERIOR SHOWING WEST SIDE AND SOUTH END DOUBLE FRENCH DOORS, AND FIBERBOARD WALLS. VIEW TO SOUTHWEST. - Big Creek Hydroelectric System, Powerhouse 8, Operator Cottage, Big Creek, Big Creek, Fresno County, CA

  3. Thermokinetic analysis and product characterization of Medium Density Fiberboard pyrolysis.

    PubMed

    Aslan, Dilan Irmak; Özoğul, Buğçe; Ceylan, Selim; Geyikçi, Feza

    2018-06-01

    This study investigates the pyrolysis of Medium Density Fiberboard (MDF) as a potential waste management solution. Thermal behaviour of MDF was analysed via TG/DSC. The primary decomposition step occurred between 190 °C and 425 °C. Evolved gaseous products over this step were evaluated by a FTIR spectrometer coupled with TGA. Peaks for phenolic, alcohols and aldehydes were detected at the maximum decomposition temperature. Py-GC/MS analysis revealed phenols, ketones and cyclic compounds as the primary non-condensable pyrolysis products. The kinetics of pyrolysis were investigated by the widely applied Distributed Activation Energy Model, resulting in an average activation energy and pre-exponential factor of 127.40 kJ mol -1 and 8.4E+11. The results of this study suggest that pyrolyzing MDF could potentially provide renewable fuels and prevent environmental problems related with MDF disposal. Copyright © 2018 Elsevier Ltd. All rights reserved.

  4. Free-Standing Canes.

    ERIC Educational Resources Information Center

    Ehresman, Paul

    1995-01-01

    A precane device, called the "free-standing cane," was developed to help children with blindness along with other disabilities. The cane detects obstacles; guides the user's hands into a relaxed, static position in front of the hips; facilitates postural security and control; and offers tactile and kinesthetic feedback. (JDD)

  5. Evaluation of new energy cane varieties for Louisiana

    USDA-ARS?s Scientific Manuscript database

    Renewed interest in U.S bioenergy markets may offer an alternative source of income for Louisiana sugarcane growers. High-fiber sugarcane or energy cane varieties are currently being developed. As with traditional sugarcane varieties, energy-cane varieties need to be evaluated across the sugarca...

  6. Sugar cane stillage: a potential source of natural antioxidants.

    PubMed

    Caderby, Emma; Baumberger, Stéphanie; Hoareau, William; Fargues, Claire; Decloux, Martine; Maillard, Marie-Noëlle

    2013-11-27

    Biorefinery of sugar cane is the first economic activity of Reunion Island. Some sugar cane manufactured products (juice, syrup, molasses) have antioxidant activities and are sources of both phenolic compounds and Maillard Reaction Products (MRP). The study aimed to highlight the global antioxidant activity of sugar cane stillage and understand its identity. Chromatographic fractionation on Sephadex LH-20 resin allowed the recovery of a MRP-rich fraction, responsible for 58 to 66% of the global antioxidant activity according to the nature of the sugar cane stillage (DPPH test), and a phenolic compounds-rich fraction for 37 to 59% of the activity. A good correlation was recorded between the antioxidant activity of the sugar cane stillage and its content in total reducing compounds amount (Folin-Ciocalteu assay), among them 2.8 to 3.9 g/L of phenolic compounds (in 5-caffeoylquinic acid equivalent). Preliminary experiments by HPLC-DAD-MS allowed to identify several free phenolic acids and gave clues to identify esters of quinic acids.

  7. Acoustic detection of Melolonthine larvae in Australian sugarcane

    USDA-ARS?s Scientific Manuscript database

    Decision support systems have been developed for risk analysis and control of root-feeding white grub pests in Queensland sugarcane, based partly on manual inspection of cane soil samples. Acoustic technology was considered as a potential alternative to this laborious procedure. Field surveys were...

  8. A New Sugarcane Cystatin Strongly Binds to Dental Enamel and Reduces Erosion.

    PubMed

    Santiago, A C; Khan, Z N; Miguel, M C; Gironda, C C; Soares-Costa, A; Pelá, V T; Leite, A L; Edwardson, J M; Buzalaf, M A R; Henrique-Silva, F

    2017-08-01

    Cystatin B was recently identified as an acid-resistant protein in acquired enamel pellicle; it could therefore be included in oral products to protect against caries and erosion. However, human recombinant cystatin is very expensive, and alternatives to its use are necessary. Phytocystatins are reversible inhibitors of cysteine peptidases that are found naturally in plants. In plants, they have several biological and physiological functions, such as the regulation of endogenous processes, defense against pathogens, and response to abiotic stress. Previous studies performed by our research group have reported high inhibitory activity and potential agricultural and medical applications of several sugarcane cystatins, including CaneCPI-1, CaneCPI-2, CaneCPI-3, and CaneCPI-4. In the present study, we report the characterization of a novel sugarcane cystatin, named CaneCPI-5. This cystatin was efficiently expressed in Escherichia coli, and inhibitory assays demonstrated that it was a potent inhibitor of human cathepsins B, K, and L ( K i = 6.87, 0.49, and 0.34 nM, respectively). The ability of CaneCPI-5 to bind to dental enamel was evaluated using atomic force microscopy. Its capacity to protect against initial enamel erosion was also tested in vitro via changes in surface hardness. CaneCPI-5 showed a very large force of interaction with enamel (e.g., compared with mucin and casein) and significantly reduced initial enamel erosion. These results suggest that the inclusion of CaneCPIs in dental products might confer protection against enamel erosion.

  9. CANES Contracting Strategies for Full Deployment

    DTIC Science & Technology

    2012-01-01

    9 CANES Program Functions in Full Deployment...contractors will design CANES, identifying specific hardware and developing the integration software necessary to consolidate existing C4I functions . At...would be responsible for execut- ing the purchased design and assembling the systems, ensuring that the integration software is functioning . An

  10. 40 CFR 409.40 - Applicability; description of the Louisiana raw cane sugar processing subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Louisiana raw cane sugar processing subcategory. 409.40 Section 409.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Louisiana Raw Cane Sugar Processing Subcategory § 409.40 Applicability; description of the...

  11. 40 CFR 409.40 - Applicability; description of the Louisiana raw cane sugar processing subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Louisiana raw cane sugar processing subcategory. 409.40 Section 409.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Louisiana Raw Cane Sugar Processing Subcategory § 409.40 Applicability; description of the...

  12. 40 CFR 409.70 - Applicability; description of the Hawaiian raw cane sugar processing subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Hawaiian raw cane sugar processing subcategory. 409.70 Section 409.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hawaiian Raw Cane Sugar Processing Subcategory § 409.70 Applicability; description of the Hawaiian...

  13. 40 CFR 409.40 - Applicability; description of the Louisiana raw cane sugar processing subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Louisiana raw cane sugar processing subcategory. 409.40 Section 409.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Louisiana Raw Cane Sugar Processing Subcategory § 409.40 Applicability; description of the...

  14. 40 CFR 409.70 - Applicability; description of the Hawaiian raw cane sugar processing subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Hawaiian raw cane sugar processing subcategory. 409.70 Section 409.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hawaiian Raw Cane Sugar Processing Subcategory § 409.70 Applicability; description of the Hawaiian...

  15. 40 CFR 409.70 - Applicability; description of the Hawaiian raw cane sugar processing subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Hawaiian raw cane sugar processing subcategory. 409.70 Section 409.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hawaiian Raw Cane Sugar Processing Subcategory § 409.70 Applicability; description of the Hawaiian...

  16. Considerations relative to the use of canes by blind travelers in air carrier aircraft cabins.

    DOT National Transportation Integrated Search

    1980-07-01

    Results are presented of specific areas of study; i.e.: : 1.passenger evacuation time lapses with and without the presence of canes; : 2.emergency exiting advantages and disadvantages with and without the presence of canes; : 3.the utility of surroga...

  17. Specific features of electrical properties of porous biocarbons prepared from beech wood and wood artificial fiberboards

    NASA Astrophysics Data System (ADS)

    Popov, V. V.; Orlova, T. S.; Magarino, E. Enrique; Bautista, M. A.; Martínez-Fernández, J.

    2011-02-01

    This paper reports on comparative investigations of the structural and electrical properties of biomorphic carbons prepared from natural beech wood, as well as medium-density and high-density fiberboards, by means of carbonization at different temperatures T carb in the range 650-1000°C. It has been demonstrated using X-ray diffraction analysis that biocarbons prepared from medium-density and high-density fiberboards at all temperatures T carb contain a nanocrystalline graphite component, namely, three-dimensional crystallites 11-14 Å in size. An increase in the carbonization temperature T carb to 1000°C leads to the appearance of a noticeable fraction of two-dimensional graphene particles with the same sizes. The temperature dependences of the electrical resistivity ρ of the biomorphic carbons have been measured and analyzed in the temperature range 1.8-300 K. For all types of carbons under investigation, an increase in the carbonization temperature T carb from 600 to 900°C leads to a change in the electrical resistivity at T = 300 K by five or six orders of magnitude. The dependences ρ( T) for these materials are adequately described by the Mott law for the variable-range hopping conduction. It has been revealed that the temperature dependence of the electrical resistivity exhibits a hysteresis, which has been attributed to thermomechanical stresses in an inhomogeneous structure of the biocarbon prepared at a low carbonization temperature T carb. The crossover to the conductivity characteristic of disordered metal systems is observed at T carb ≳ 1000°C.

  18. Effects of emissions from sugar cane burning on the trachea and lungs of Wistar rats

    PubMed Central

    Matos, Verena Sampaio Barbosa; Gomes, Felipe da Silva; Oliveira, Tarcio Macena; Schulz, Renata da Silva; Ribeiro, Lídia Cristina Villela; Gonzales, Astria Dias Ferrão; Lima, Januário Mourão; Guerreiro, Marcos Lázaro da Silva

    2017-01-01

    ABSTRACT Objective: To evaluate the effects of exposure to emissions from sugar cane burning on inflammatory mechanisms in tissues of the trachea and lung parenchyma in Wistar rats after different periods of exposure. Methods: This was an experimental open randomized study. The animals were divided into four groups: a control group (CG) underwent standard laboratory conditions, and three experimental groups were exposed to emissions from sugar cane burning over different periods of time, in days-1 (EG1), 7 (EG7), and 21 (EG21). After euthanasia with 200 mg/kg of ketamine/xylazine, fragments of trachea and lung were collected and fixed in 10% formalin. Histological analyses were performed with H&E and picrosirius red staining. Results: No inflammatory infiltrates were found in the tissues of CG rats. The histological examination of tissues of the trachea and lung parenchyma revealed that the inflammatory process was significantly more intense in EG7 than in the CG (p < 0.05 and p < 0.01, respectively). In comparison with the CG and EG1, angiogenesis in the lung parenchyma and collagen deposition in tracheal tissues were significantly greater only in EG21 (p < 0.001 and p < 0.01, respectively). Conclusions: In this sample, emissions from sugar cane burning induced acute focal and diffuse inflammation in the lamina propria of tracheal tissues, with no loss of ciliated epithelial tissue. In the lung parenchyma of the animals in the experimental groups, there was interstitial and alveolar edema, together with polymorphonuclear cell infiltrates. PMID:28746532

  19. 7 CFR 1435.305 - State cane sugar allotments.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false State cane sugar allotments. 1435.305 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.305 State cane sugar allotments. (a) Hawaii and Puerto Rico will be allotted a total...

  20. 7 CFR 1435.305 - State cane sugar allotments.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false State cane sugar allotments. 1435.305 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.305 State cane sugar allotments. (a) Hawaii and Puerto Rico will be allotted a total...

  1. 40 CFR 409.80 - Applicability; description of the Puerto Rican raw cane sugar processing subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Puerto Rican raw cane sugar processing subcategory. 409.80 Section 409.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Puerto Rican Raw Cane Sugar Processing Subcategory § 409.80 Applicability; description of the...

  2. 7 CFR 1435.305 - State cane sugar allotments.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false State cane sugar allotments. 1435.305 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.305 State cane sugar allotments. (a) Hawaii and Puerto Rico will be allotted a total...

  3. 7 CFR 1435.305 - State cane sugar allotments.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false State cane sugar allotments. 1435.305 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.305 State cane sugar allotments. (a) Hawaii and Puerto Rico will be allotted a total...

  4. 7 CFR 1435.305 - State cane sugar allotments.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false State cane sugar allotments. 1435.305 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.305 State cane sugar allotments. (a) Hawaii and Puerto Rico will be allotted a total...

  5. 40 CFR 409.80 - Applicability; description of the Puerto Rican raw cane sugar processing subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Puerto Rican raw cane sugar processing subcategory. 409.80 Section 409.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Puerto Rican Raw Cane Sugar Processing Subcategory § 409.80 Applicability; description of the...

  6. 40 CFR 409.80 - Applicability; description of the Puerto Rican raw cane sugar processing subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Puerto Rican raw cane sugar processing subcategory. 409.80 Section 409.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Puerto Rican Raw Cane Sugar Processing Subcategory § 409.80 Applicability; description of the...

  7. Waist-up protection for blind individuals using the EyeCane as a primary and secondary mobility aid.

    PubMed

    Buchs, Galit; Simon, Noa; Maidenbaum, Shachar; Amedi, Amir

    2017-01-01

    One of the most stirring statistics in relation to the mobility of blind individuals is the high rate of upper body injuries, even when using the white-cane. We here addressed a rehabilitation- oriented challenge of providing a reliable tool for blind people to avoid waist-up obstacles, namely one of the impediments to their successful mobility using currently available methods (e.g., white-cane). We used the EyeCane, a device we developed which translates distances from several angles to haptic and auditory cues in an intuitive and unobtrusive manner, serving both as a primary and secondary mobility aid. We investigated the rehabilitation potential of such a device in facilitating visionless waist-up body protection. After ∼5 minutes of training with the EyeCane blind participants were able to successfully detect and avoid obstacles waist-high and up. This was significantly higher than their success when using the white-cane alone. As avoidance of obstacles required participants to perform an additional cognitive process after their detection, the avoidance rate was significantly lower than the detection rate. Our work has demonstrated that the EyeCane has the potential to extend the sensory world of blind individuals by expanding their currently accessible inputs, and has offered them a new practical rehabilitation tool.

  8. Land use change effects on GHG dynamics in Central Florida

    NASA Astrophysics Data System (ADS)

    DeLucia, N.; Bernacchi, C. J.; Gomez-Casanovas, N.

    2012-12-01

    The need for alternative energies is accelerating land use change as native or managed ecosystems are being converted to intense agricultural crops for biofuel purposes. Agriculture represents the single largest terrestrial flux of nitrous oxide (N2O) to the atmosphere resulting from nutrient applications. Livestock grazing also accounts for a significant release of methane (CH4) to the atmosphere. Together, CO2, N2O and CH4 represent the dominant greenhouse gasses (GHG) that are emitted to the atmosphere through anthropogenic influences. Significant alterations to the land surface, particularly associated with changes in nutrient application rates, ability of vegetation to uptake nutrients, or changes in the stocking density of livestock, could have a meaningful impact on GHG emissions. Therefore, understanding how these changes will affect soil GHG dynamics is essential to quantify the impact of land use change on the global climate system. Large-scale changes to land cover type in Central Florida Highlands County is currently occurring in which improved pasture (bahiagrass, Paspalum notatum L., as forage for cattle, Bos taurus L.) is being replaced by energy cane (genus Saccharum L.). Fluxes of nitrous oxide (N2O), soil carbon dioxide (CO2) and methane (CH4) were obtained over a complete wet-dry seasonal cycle in a grazed pasture and an energy cane plantation located in Highlands County, FL. In addition, we also investigated the biotic and environmental drivers that regulate soil GHG fluxes in these ecosystems. We predicted decreased rates of CH4 released to the atmosphere after the conversion process was completed to energy cane due to the absence of grazing cattle. We also predicted increased N2O emissions from aggressive fertilization of energycane. Using static chamber measurements, we collected gas samples from four energy cane crops at varying ages and improved pastures paired to each energy cane plot. The gas samples were analyzed using gas chromatography. Overall, the emission of N2O from the energy cane was similar to that from the grazed improved pastures, except following fertilization when N2O from energycane plots was higher. Soils from grazed pasture and energycane were a sink of CH4, with the exception of one energycane plot established in Nov. 2011 that emitted more CH4 immediately after planting. Including cattle induced CH4 emissions in the improved pasture results in the energycane plots having significantly lower total CH4 emissions relative to the existing land cover. Despite the differences in emissions of GHG from the land cover types and the confounding variables associated with soil type and natural variability, our results suggest that land use change induced by the establishment of biofuel crops in Central Florida will lead to less GHG emissions. Coupled with the dynamics associated with higher CO2 uptake by energycane, the biofuel crops can provide ecosystem services that extend beyond renewable fuel.

  9. The German version of the Camberwell Assessment of Need for the Elderly (CANE): evaluation of content validity and adaptation to the German-speaking context.

    PubMed

    Stein, Janine; Luppa, Melanie; König, Hans-Helmut; Riedel-Heller, Steffi G

    2015-11-01

    The Camberwell Assessment of Need for the Elderly (CANE) was developed for the assessment of physical-, psychological-, and environment-related needs in the elderly. The aim of this study was to revise and adapt the German version of the CANE with regard to the content validity of the instrument. Following a multistage approach, face-to-face interviews using the CANE, an expert survey and a multidisciplinary consensus conference were conducted in order to evaluate the frequency and relevance of met and unmet needs in the German elderly population, and to modify the content of the CANE for the German-speaking countries. In Germany, unmet physical needs including physical health, medication, eyesight/hearing/communication, mobility/falls, self-care, and continence were found to have top priority closely followed by social needs (company, intimate relationships, daytime activities, information, and abuse/neglect). Psychological needs were the lowest ranked care category. Experts' proposals for the improvement of the German version of the CANE were collected. All findings were discussed and integrated in the multidisciplinary consensus conference with the result of a revised and adapted CANE that is applicable in the German-speaking context. The provision of an adapted and improved German version of the CANE may substantially contribute to a comprehensive and valid assessment of needs in the elderly population. The results of this study represent an important basis for comprehensive needs assessment in the elderly in the theoretical and practical field of healthcare and health services research.

  10. 7 CFR 1435.304 - Beet and cane sugar allotments.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Beet and cane sugar allotments. 1435.304 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.304 Beet and cane sugar allotments. (a) The allotment for beet sugar will be 54.35...

  11. 7 CFR 1435.304 - Beet and cane sugar allotments.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false Beet and cane sugar allotments. 1435.304 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.304 Beet and cane sugar allotments. (a) The allotment for beet sugar will be 54.35...

  12. 21 CFR 890.3790 - Cane, crutch, and walker tips and pads.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Cane, crutch, and walker tips and pads. 890.3790 Section 890.3790 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3790 Cane...

  13. 21 CFR 890.3790 - Cane, crutch, and walker tips and pads.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cane, crutch, and walker tips and pads. 890.3790 Section 890.3790 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3790 Cane...

  14. 21 CFR 890.3790 - Cane, crutch, and walker tips and pads.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Cane, crutch, and walker tips and pads. 890.3790 Section 890.3790 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3790 Cane...

  15. 21 CFR 890.3790 - Cane, crutch, and walker tips and pads.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Cane, crutch, and walker tips and pads. 890.3790 Section 890.3790 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3790 Cane...

  16. 21 CFR 890.3790 - Cane, crutch, and walker tips and pads.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Cane, crutch, and walker tips and pads. 890.3790 Section 890.3790 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Prosthetic Devices § 890.3790 Cane...

  17. 40 CFR 409.50 - Applicability; description of the Florida and Texas raw cane sugar processing subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Florida and Texas raw cane sugar processing subcategory. 409.50 Section 409.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Florida and Texas Raw Cane Sugar Processing Subcategory § 409.50 Applicability; description of the...

  18. 7 CFR 1435.304 - Beet and cane sugar allotments.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Beet and cane sugar allotments. 1435.304 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.304 Beet and cane sugar allotments. (a) The allotment for beet sugar will be 54.35...

  19. 40 CFR 409.50 - Applicability; description of the Florida and Texas raw cane sugar processing subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Florida and Texas raw cane sugar processing subcategory. 409.50 Section 409.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Florida and Texas Raw Cane Sugar Processing Subcategory § 409.50 Applicability; description of the...

  20. 7 CFR 1435.304 - Beet and cane sugar allotments.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Beet and cane sugar allotments. 1435.304 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.304 Beet and cane sugar allotments. (a) The allotment for beet sugar will be 54.35...

  1. 7 CFR 1435.304 - Beet and cane sugar allotments.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Beet and cane sugar allotments. 1435.304 Section 1435..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.304 Beet and cane sugar allotments. (a) The allotment for beet sugar will be 54.35...

  2. 40 CFR 409.50 - Applicability; description of the Florida and Texas raw cane sugar processing subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Florida and Texas raw cane sugar processing subcategory. 409.50 Section 409.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Florida and Texas Raw Cane Sugar Processing Subcategory § 409.50 Applicability; description of the...

  3. The Effect of Green Sugarcane on Downstream Processing at Two Midlands Factories

    USDA-ARS?s Scientific Manuscript database

    There is a worldwide shift to green cane from burnt cane harvesting. In many countries including the U.S. and South Africa, certain areas are changing to green cane harvesting due to public and environmental pressures against open field burning, increasing labor costs, and the current trend to inve...

  4. How much fertilizer nitrogen does sugarcane need?

    USDA-ARS?s Scientific Manuscript database

    Nitrogen rate recommendations for sugarcane in Louisiana take into account crop age (plant cane or stubble) and soil texture (light or heavy). Recommended rates in the 1950s ranged from 40 pounds N/A for plant cane on light-textured soil to 100 pounds of N/A for stubble cane on heavy-textured soil a...

  5. Enhanced poly(L-malic acid) production from pretreated cane molasses by Aureobasidium pullulans in fed-batch fermentation.

    PubMed

    Xia, Jun; Xu, Jiaxing; Hu, Lei; Liu, Xiaoyan

    2016-11-16

    Poly(L-malic acid) (PMA) is a natural polyester with many attractive properties for biomedical application. However, the cost of PMA production is high when glucose is used as a carbon source. To solve this problem, cane molasses as a low-cost feedstock was applied for the production of PMA. Six pretreatment methods were applied to cane molasses before fermentation. Pretreatment with combined tricalcium phosphate, potassium ferrocyanide, and sulfuric acid (TPFSA) removed significant amounts of metal ions from cane molasses. The PMA concentration increased from 5.4 g/L (untreated molasses) to 36.9 g/L (TPFSA-pretreated molasses) after fermentation in shake flasks. A fed-batch fermentation strategy was then developed. In this method, TPFSA-pretreated cane molasses solution was continuously fed into the fermentor to maintain the total sugar concentration at 20 g/L. This technique generated approximately 95.4 g/L PMA with a productivity of 0.57 g/L/hr. The present study indicated that fed-batch fermentation using pretreated cane molasses is a feasible technique for producing high amounts of PMA.

  6. 49 CFR 178.516 - Standards for fiberboard boxes.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... minutes by the Cobb method of determining water absorption, is not greater than 155 g per square meter (0...) Maximum net mass: 400 kg (882 pounds). [Amdt. 178-97, 55 FR 52717, Dec. 21, 1990, and amended by Amdt. 178...

  7. 49 CFR 173.184 - Highway or rail fusee.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) boxes, wooden (4C1, 4C2), plywood (4D) or reconstituted wood (4F) boxes or in fiberboard boxes (4G... drop test requirements (§ 178.603 of this subchapter), including at least one drop with spike in a...

  8. 49 CFR 173.184 - Highway or rail fusee.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...) boxes, wooden (4C1, 4C2), plywood (4D) or reconstituted wood (4F) boxes or in fiberboard boxes (4G... drop test requirements (§ 178.603 of this subchapter), including at least one drop with spike in a...

  9. Medium density fiberboard made from Eucalyptus saligna

    Treesearch

    Andrzej M. Krzysik; James H. Muehl; John A. Youngquist; Fabio Spina Franca

    2001-01-01

    The production of industrial wood from natural forests is predicted to decline in the future. Factors that will contribute to this decline include changes in land use patterns, depletion of resources in some parts of the world, and the withdrawal of...

  10. Chemistry Based on Renewable Raw Materials: Perspectives for a Sugar Cane-Based Biorefinery

    PubMed Central

    Villela Filho, Murillo; Araujo, Carlos; Bonfá, Alfredo; Porto, Weber

    2011-01-01

    Carbohydrates are nowadays a very competitive feedstock for the chemical industry because their availability is compatible with world-scale chemical production and their price, based on the carbon content, is comparable to that of petrochemicals. At the same time, demand is rising for biobased products. Brazilian sugar cane is a competitive feedstock source that is opening the door to a wide range of bio-based products. This essay begins with the importance of the feedstock for the chemical industry and discusses developments in sugar cane processing that lead to low cost feedstocks. Thus, sugar cane enables a new chemical industry, as it delivers a competitive raw material and a source of energy. As a result, sugar mills are being transformed into sustainable biorefineries that fully exploit the potential of sugar cane. PMID:21637329

  11. Design and construction of smart cane using infrared laser-based tracking system

    NASA Astrophysics Data System (ADS)

    Wong, Chi Fung; Phitagragsakul, Narikorn; Jornsamer, Patcharaporn; Kaewmeesri, Pimsin; Jantakot, Pimsunan; Locharoenrat, Kitsakorn

    2018-06-01

    Our work is aimed to design and construct the smart cane. The infrared laser-based sensor was used as a distance detector and Arduino board was used as a microcontroller. On the other hand, Bluetooth was used as a wireless communicator and MP3 module together with the headset were used as a voice alert player. Our smart cane is a very effective device for the users under the indoor guidance. That is, the obstacle was detectable 3,000 cm away from the blind people. The white cane was assembled with the laser distance sensor and distance alert sensor served as the compact and light-weight device. Distance detection was very fast and precise when the smart cane was tested for the different obstacles, such as human, wall and wooden table under the indoor area.

  12. Proteomic analysis of Herbaspirillum seropedicae cultivated in the presence of sugar cane extract.

    PubMed

    Cordeiro, Fabio Aparecido; Tadra-Sfeir, Michelle Zibetti; Huergo, Luciano Fernandes; de Oliveira Pedrosa, Fábio; Monteiro, Rose Adele; de Souza, Emanuel Maltempi

    2013-03-01

    Bacterial endophytes of the genus Herbaspirillum colonize sugar cane and can promote plant growth. The molecular mechanisms that mediate plant- H. seropedicae interaction are poorly understood. In this work, we used 2D-PAGE electrophoresis to identify H. seropedicae proteins differentially expressed at the log growth phase in the presence of sugar cane extract. The differentially expressed proteins were validated by RT qPCR. A total of 16 differential spots (1 exclusively expressed, 7 absent, 5 up- and 3 down-regulated) in the presence of 5% sugar cane extract were identified; thus the host extract is able to induce and repress specific genes of H. seropedicae. The differentially expressed proteins suggest that exposure to sugar cane extract induced metabolic changes and adaptations in H. seropedicae presumably in preparation to establish interaction with the plant.

  13. Chemistry based on renewable raw materials: perspectives for a sugar cane-based biorefinery.

    PubMed

    Villela Filho, Murillo; Araujo, Carlos; Bonfá, Alfredo; Porto, Weber

    2011-01-01

    Carbohydrates are nowadays a very competitive feedstock for the chemical industry because their availability is compatible with world-scale chemical production and their price, based on the carbon content, is comparable to that of petrochemicals. At the same time, demand is rising for biobased products. Brazilian sugar cane is a competitive feedstock source that is opening the door to a wide range of bio-based products. This essay begins with the importance of the feedstock for the chemical industry and discusses developments in sugar cane processing that lead to low cost feedstocks. Thus, sugar cane enables a new chemical industry, as it delivers a competitive raw material and a source of energy. As a result, sugar mills are being transformed into sustainable biorefineries that fully exploit the potential of sugar cane.

  14. Conversion of Grazed Pastures to Energy Cane as a Biofuel Feedstock Alters Soil GHG Fluxes

    NASA Astrophysics Data System (ADS)

    Gomez-Casanovas, N.; DeLucia, N.; Bernacchi, C.; DeLucia, E. H.

    2013-12-01

    Changes in land use profoundly affect climate through variations in soil Greenhouse Gas (GHG) exchange. The need for alternative energies is accelerating land use change as marginal land or managed ecosystems are being converted to highly productive second-generation bioenergy crops such as energy cane (Saccharum spp. L). Although the deployment of energy cane is a promising strategy to meet global bioenergy industry demands, few studies have investigated soil GHG fluxes in these crops and sub-tropical low-intensity grazing pasture (bahiagrass, Paspalum notatum L., as forage for cattle, Bos taurus L.) with which they are competing for land. Here, we showed that soil N2O fluxes in bioenergy crops were higher (>250%) than those observed in pastures following fertilization when soil moisture and temperature were high. In the absence of recent fertilization, the N2O source strength in energy cane and pasture sites was similar. Under drier and cooler soil conditions, both pastures and bioenergy crops were weak sources of N2O even when energy cane plots were recently fertilized. Soils on grazed pastures were sources of CH4 during the wet season but became sinks under drier, colder conditions. Energy cane plantations were weak sources of CH4 over a complete wet-dry seasonal cycle. The heterotrophic component of soil respiration was larger (139-155%) in pastures than in energy cane crops, suggesting lower decomposition of SOC in bioenergy crops. In terms of global warming potential, grazed pastures were stronger (120-150%) soil GHG emitters than energy cane crops over a complete wet-dry seasonal cycle. Moreover, pastures became a substantial source of GHG emitters when including estimates of CH4 flux from cattle. Our results suggest that the conversion of pasture to energy cane will be beneficial in relation to GHGs emitted from soils and cattle. Improved understanding of land use impact on soil GHG dynamics will provide valuable information for decision makers debating sustainable bioenergy policies.

  15. The impact of stress on the health of sugar cane cutters

    PubMed Central

    Priuli, Roseana Mara Aredes; de Moraes, Maria Silvia; Chiaravalloti, Rafael Morais

    2014-01-01

    OBJECTIVE Evaluate the impact of stress on sugar cane cutters and the prevalence of physical and psychological symptoms before and after harvest. METHODS We studied 114 sugarcane cutters and 109 urban workers in the pre-harvest and 102 sugar cane cutters and 81 urban workers in the post-harvest period in the city of Mendonça, SP, Southeastern Brazil, in 2009. Data analysis was based on the frequency and percentage of the assessed symptoms of stress, using the Lipp-ISSL test (Symptoms of Stress for Adults). The data were analyzed using descriptive statistics. The Fisher Test was used to compare the variable of stress between pre- and post-harvest within the sugar cane cutter and urban worker groups. P values below 0.05 were considered significant. RESULTS Stress in sugar cane cutters increased after harvesting (34.2% pre-harvest and 46.1% post-harvest); in urban workers, stress decreased from 44.0% pre-harvest to 42.0% post-harvest. There was prevalence of the phase of resistance to stress for both groups with signs more apparent from the near-exhaustion and exhaustion phases for sugar cane cutters. After harvest, there was a tendency for the number of sugar cane cutters with symptoms of near-exhaustion (6.4%) and exhaustion (10.6%) to increase. After harvest there was a trend for the number of sugar cane cutters with physical symptoms (pre-harvest = 20.5%, post-harvest = 25.5%) and psychological symptoms (pre-harvest = 64.1%; post-harvest = 70.2%) to increase. For both groups, predominantly psychological symptoms occurred in both phases (70.2% versus 64.7%). CONCLUSIONS The work process of cutting cane can cause stress. Individual factors such as cognitive perception of the experience, self-efficacy beliefs and expectations of the employee regarding their performance can influence the understanding of the reactions in their body in face of the work. PMID:24897043

  16. The impact of stress on the health of sugar cane cutters.

    PubMed

    Priuli, Roseana Mara Aredes; Moraes, Maria Silvia de; Chiaravalloti, Rafael Morais

    2014-04-01

    Evaluate the impact of stress on sugar cane cutters and the prevalence of physical and psychological symptoms before and after harvest. We studied 114 sugarcane cutters and 109 urban workers in the pre-harvest and 102 sugar cane cutters and 81 urban workers in the post-harvest period in the city of Mendonça, SP, Southeastern Brazil, in 2009. Data analysis was based on the frequency and percentage of the assessed symptoms of stress, using the Lipp-ISSL test (Symptoms of Stress for Adults). The data were analyzed using descriptive statistics. The Fisher Test was used to compare the variable of stress between pre- and post-harvest within the sugar cane cutter and urban worker groups. P values below 0.05 were considered significant. Stress in sugar cane cutters increased after harvesting (34.2% pre-harvest and 46.1% post-harvest); in urban workers, stress decreased from 44.0% pre-harvest to 42.0% post-harvest. There was prevalence of the phase of resistance to stress for both groups with signs more apparent from the near-exhaustion and exhaustion phases for sugar cane cutters. After harvest, there was a tendency for the number of sugar cane cutters with symptoms of near-exhaustion (6.4%) and exhaustion (10.6%) to increase. After harvest there was a trend for the number of sugar cane cutters with physical symptoms (pre-harvest = 20.5%, post-harvest = 25.5%) and psychological symptoms (pre-harvest = 64.1%; post-harvest = 70.2%) to increase. For both groups, predominantly psychological symptoms occurred in both phases (70.2% versus 64.7%). The work process of cutting cane can cause stress. Individual factors such as cognitive perception of the experience, self-efficacy beliefs and expectations of the employee regarding their performance can influence the understanding of the reactions in their body in face of the work.

  17. A Suspected Parasite Spill-Back of Two Novel Myxidium spp. (Myxosporea) Causing Disease in Australian Endemic Frogs Found in the Invasive Cane Toad

    PubMed Central

    Hartigan, Ashlie; Fiala, Ivan; Dyková, Iva; Jirků, Miloslav; Okimoto, Ben; Rose, Karrie; Phalen, David N.; Šlapeta, Jan

    2011-01-01

    Infectious diseases are contributing to the decline of endangered amphibians. We identified myxosporean parasites, Myxidium spp. (Myxosporea: Myxozoa), in the brain and liver of declining native frogs, the Green and Golden Bell frog (Litoria aurea) and the Southern Bell frog (Litoria raniformis). We unequivocally identified two Myxidium spp. (both generalist) affecting Australian native frogs and the invasive Cane toad (Bufo marinus, syn. Rhinella marina) and demonstrated their association with disease. Our study tested the identity of Myxidium spp. within native frogs and the invasive Cane toad (brought to Australia in 1935, via Hawaii) to resolve the question whether the Cane toad introduced them to Australia. We showed that the Australian brain and liver Myxidium spp. differed 9%, 7%, 34% and 37% at the small subunit rDNA, large subunit rDNA, internal transcribed spacers 1 and 2, but were distinct from Myxidium cf. immersum from Cane toads in Brazil. Plotting minimum within-group distance against maximum intra-group distance confirmed their independent evolutionary trajectory. Transmission electron microscopy revealed that the brain stages localize inside axons. Myxospores were morphologically indistinguishable, therefore genetic characterisation was necessary to recognise these cryptic species. It is unlikely that the Cane toad brought the myxosporean parasites to Australia, because the parasites were not found in 261 Hawaiian Cane toads. Instead, these data support the enemy-release hypothesis predicting that not all parasites are translocated with their hosts and suggest that the Cane toad may have played an important spill-back role in their emergence and facilitated their dissemination. This work emphasizes the importance of accurate species identification of pathogens relevant to wildlife management and disease control. In our case it is paving the road for the spill-back role of the Cane toad and the parasite emergence. PMID:21541340

  18. Development of voice navigation system for the visually impaired by using IC tags.

    PubMed

    Takatori, Norihiko; Nojima, Kengo; Matsumoto, Masashi; Yanashima, Kenji; Magatani, Kazushige

    2006-01-01

    There are about 300,000 visually impaired persons in Japan. Most of them are old persons and, cannot become skillful in using a white cane, even if they make effort to learn how to use a white cane. Therefore, some guiding system that supports the independent activities of the visually impaired are required. In this paper, we will describe about a developed white cane system that supports the independent walking of the visually impaired in the indoor space. This system is composed of colored navigation lines that include IC tags and an intelligent white cane that has a navigation computer. In our system colored navigation lines that are put on the floor of the target space from the start point to the destination and IC tags that are set at the landmark point are used for indication of the route to the destination. The white cane has a color sensor, an IC tag transceiver and a computer system that includes a voice processor. This white cane senses the navigation line that has target color by a color sensor. When a color sensor finds the target color, the white cane informs a white cane user that he/she is on the navigation line by vibration. So, only following this vibration, the user can reach the destination. However, at some landmark points, guidance is necessary. At these points, an IC tag is set under the navigation line. The cane makes communication with the tag and informs the user about the land mark pint by pre recorded voice. Ten normal subjects who were blindfolded were tested with our developed system. All of them could walk along navigation line. And the IC tag information system worked well. Therefore, we have concluded that our system will be a very valuable one to support activities of the visually impaired.

  19. Sugar composition and concentrations in sugarcane juice as affected by sampling date and internode position

    USDA-ARS?s Scientific Manuscript database

    Sugarcane (Saccharum spp. hybrids) harvest season lasts about six months from late-October through mid-April in Florida. Cane juice sugar concentration and composition are important for sucrose yield and profits, however research is lacking on the influence of harvesting time and intermodal position...

  20. Elevation of a cane-growing area of the state of Sao Paulo using LANDSAT data

    NASA Technical Reports Server (NTRS)

    Dejesusparada, N. (Principal Investigator); Mendonca, F. J.; Lee, D. C. L.; Tardin, A. T.; Shimabukuro, Y. E.; Chen, S. C.; Lucht, L. A. M.; Moreira, M. A.; Delima, A. M.; Maia, F. C. S.

    1981-01-01

    Images at a scale of 1:250.000 were visually interpreted for identification and area estimates of sugar cane plantations in Sao Paulo. The basic criteria for crop identification were the spectral characteristics of channels 5 and 7 and their temporal variations observed from different LANDSAT passes. Using this technique, it was possible to map the sugar cane areas as well as the sugar cane already harvested. An area of 801,950 hectares was estimated within the study area. The confidence interval of correct classification ranged from 87.11% to 94.71%.

  1. Haptic Cues for Balance: Use of a Cane Provides Immediate Body Stabilization

    PubMed Central

    Sozzi, Stefania; Crisafulli, Oscar; Schieppati, Marco

    2017-01-01

    Haptic cues are important for balance. Knowledge of the temporal features of their effect may be crucial for the design of neural prostheses. Touching a stable surface with a fingertip reduces body sway in standing subjects eyes closed (EC), and removal of haptic cue reinstates a large sway pattern. Changes in sway occur rapidly on changing haptic conditions. Here, we describe the effects and time-course of stabilization produced by a haptic cue derived from a walking cane. We intended to confirm that cane use reduces body sway, to evaluate the effect of vision on stabilization by a cane, and to estimate the delay of the changes in body sway after addition and withdrawal of haptic input. Seventeen healthy young subjects stood in tandem position on a force platform, with eyes closed or open (EO). They gently lowered the cane onto and lifted it from a second force platform. Sixty trials per direction of haptic shift (Touch → NoTouch, T-NT; NoTouch → Touch, NT-T) and visual condition (EC-EO) were acquired. Traces of Center of foot Pressure (CoP) and the force exerted by cane were filtered, rectified, and averaged. The position in space of a reflective marker positioned on the cane tip was also acquired by an optoelectronic device. Cross-correlation (CC) analysis was performed between traces of cane tip and CoP displacement. Latencies of changes in CoP oscillation in the frontal plane EC following the T-NT and NT-T haptic shift were statistically estimated. The CoP oscillations were larger in EC than EO under both T and NT (p < 0.001) and larger during NT than T conditions (p < 0.001). Haptic-induced effect under EC (Romberg quotient NT/T ~ 1.2) was less effective than that of vision under NT condition (EC/EO ~ 1.5) (p < 0.001). With EO cane had little effect. Cane displacement lagged CoP displacement under both EC and EO. Latencies to changes in CoP oscillations were longer after addition (NT-T, about 1.6 s) than withdrawal (T-NT, about 0.9 s) of haptic input (p < 0.001). These latencies were similar to those occurring on fingertip touch, as previously shown. Overall, data speak in favor of substantial equivalence of the haptic information derived from both “direct” fingertip contact and “indirect” contact with the floor mediated by the cane. Cane, finger and visual inputs would be similarly integrated in the same neural centers for balance control. Haptic input from a walking aid and its processing time should be considered when designing prostheses for locomotion. PMID:29311785

  2. Waist-up protection for blind individuals using the EyeCane as a primary and secondary mobility aid

    PubMed Central

    Buchs, Galit; Simon, Noa; Maidenbaum, Shachar; Amedi, Amir

    2017-01-01

    Background: One of the most stirring statistics in relation to the mobility of blind individuals is the high rate of upper body injuries, even when using the white-cane. Objective: We here addressed a rehabilitation- oriented challenge of providing a reliable tool for blind people to avoid waist-up obstacles, namely one of the impediments to their successful mobility using currently available methods (e.g., white-cane). Methods: We used the EyeCane, a device we developed which translates distances from several angles to haptic and auditory cues in an intuitive and unobtrusive manner, serving both as a primary and secondary mobility aid. We investigated the rehabilitation potential of such a device in facilitating visionless waist-up body protection. Results: After ∼5 minutes of training with the EyeCane blind participants were able to successfully detect and avoid obstacles waist-high and up. This was significantly higher than their success when using the white-cane alone. As avoidance of obstacles required participants to perform an additional cognitive process after their detection, the avoidance rate was significantly lower than the detection rate. Conclusion: Our work has demonstrated that the EyeCane has the potential to extend the sensory world of blind individuals by expanding their currently accessible inputs, and has offered them a new practical rehabilitation tool. PMID:28157111

  3. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... antimicrobial agent, as defined in § 170.3(o)(2) of this chapter, in raw sugar cane juice. It is added prior to clarification when further processing of the sugar cane juice must be delayed. (d) The additive is applied to the sugar juice in the following quantities, based on the weight of the raw cane: Component Parts per...

  4. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... antimicrobial agent, as defined in § 170.3(o)(2) of this chapter, in raw sugar cane juice. It is added prior to clarification when further processing of the sugar cane juice must be delayed. (d) The additive is applied to the sugar juice in the following quantities, based on the weight of the raw cane: Component Parts per...

  5. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... antimicrobial agent, as defined in § 170.3(o)(2) of this chapter, in raw sugar cane juice. It is added prior to clarification when further processing of the sugar cane juice must be delayed. (d) The additive is applied to the sugar juice in the following quantities, based on the weight of the raw cane: Component Parts per...

  6. 75 FR 53013 - Fiscal Year 2011 Tariff-rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-30

    ... for Raw Cane Sugar, Refined and Specialty Sugar, and Sugar-containing Products; Revision AGENCY... August 17, 2010 concerning Fiscal Year 2011 tariff-rate quota allocations of raw cane sugar, refined and... announced that sugar entering the United States under the Fiscal Year 2011 raw sugar tariff-rate quota will...

  7. 76 FR 36512 - USDA Increases the Domestic Sugar Overall Allotment Quantity, Reassigns Domestic Cane Sugar...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-22

    ... Allotment Quantity, Reassigns Domestic Cane Sugar Allotments, and Increases the Fiscal Year 2011 Raw Sugar... of surplus sugar under domestic cane sugar allotments of 120,000 short tons raw value (STRV) to imports; and an increase in the fiscal year (FY) 2011 raw sugar tariff-rate quota (TRQ) of the same amount...

  8. 75 FR 39612 - Allocation of Second Additional Fiscal Year (FY) 2010 In-Quota Volume for Raw Cane Sugar

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-09

    ...) 2010 In-Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative... the tariff-rate quota (TRQ) for imported raw cane sugar. DATES: Effective Date: July 9, 2010... Harmonized Tariff Schedule of the United States (HTS), the United States maintains TRQs for imports of raw...

  9. 21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

  10. 21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

  11. Greenhouse and field performance of giant cane propagules from natural and planted stands

    Treesearch

    William W. Brendecke; James J. Zaczek

    2008-01-01

    The objective of this study was to determine whether giant cane (Arundinaria gigantea) vegetative macropropagules of nine stock types could generate surviving culms to be used in restoration plantings in southern Illinois. In spring 2006, studies were conducted to compare culm production and survival of giant cane stock types that had varying rhizome...

  12. 21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

  13. 40 CFR 409.60 - Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane sugar...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...-Hamakua Coast of the Island of Hawaii raw cane sugar processing subcategory. 409.60 Section 409.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hilo-Hamakua Coast of the Island of Hawaii Raw Cane Sugar Processing...

  14. 40 CFR 409.60 - Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane sugar...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...-Hamakua Coast of the Island of Hawaii raw cane sugar processing subcategory. 409.60 Section 409.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hilo-Hamakua Coast of the Island of Hawaii Raw Cane Sugar Processing...

  15. 40 CFR 409.60 - Applicability; description of the Hilo-Hamakua Coast of the Island of Hawaii raw cane sugar...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...-Hamakua Coast of the Island of Hawaii raw cane sugar processing subcategory. 409.60 Section 409.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Hilo-Hamakua Coast of the Island of Hawaii Raw Cane Sugar Processing...

  16. 21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

  17. Materials Testing in Long Cane Design: Sensitivity, Flexibility, and Transmission of Vibration

    ERIC Educational Resources Information Center

    Rodgers, Mark D.; Emerson, Robert Wall

    2005-01-01

    Different materials that are used in manufacturing long cane shafts were assessed for their ability to transmit vibration and their sensitivity to tactile information, flexibility, and durability. It was found that the less flexible a cane shaft is, the better it transmits vibrations that are useful for discriminating surface textures and that…

  18. How to manage cane in the field and factory following damaging freezes

    USDA-ARS?s Scientific Manuscript database

    The exposure of sugar cane to damaging frosts occurs in approximately 25% of the sugar cane producing countries world-wide. A series of damaging freezes, -2.6, -3.3 and -2.1°C, occurred in Morocco on 4, 5 and 13 February 2012, respectively, only 2 weeks after the commencement of the harvest season. ...

  19. Productivity of 'Triple Crown' blackberry on the rotating cross-arm trellis system

    USDA-ARS?s Scientific Manuscript database

    Blackberry plants are vigorous and produce long lateral canes. However, to keep the plant canopy narrow for better spray coverage and to aid in fruit harvesting, the canes are typically pruned severely (e.g. primocanes are topped at the 6-ft height and the lateral canes are cut back to 18- to 24-in...

  20. 49 CFR 173.184 - Highway or rail fusee.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... (3A2), wooden (4C1, 4C2), plywood (4D) or reconstituted wood (4F) boxes or in fiberboard boxes (4G... drop test requirements (§ 178.603 of this subchapter), including at least one drop with spike in a...

  1. 49 CFR 173.184 - Highway or rail fusee.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... (3A2), wooden (4C1, 4C2), plywood (4D) or reconstituted wood (4F) boxes or in fiberboard boxes (4G... drop test requirements (§ 178.603 of this subchapter), including at least one drop with spike in a...

  2. 49 CFR 173.184 - Highway or rail fusee.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... (3A2), wooden (4C1, 4C2), plywood (4D) or reconstituted wood (4F) boxes or in fiberboard boxes (4G... drop test requirements (§ 178.603 of this subchapter), including at least one drop with spike in a...

  3. Environmentally Benign Battlefield Effects Black Smoke Simulator

    DTIC Science & Technology

    2006-11-01

    tested and results Fuel Oxidizer Color of Smoke Density of Smoke Sugar (Sucrose) KNO3 Grey Medium Dextrin KNO3 Grey Thin Microcrystalline...design. 3.5 Initial Prototype Scale Fiberboard Testing Several quality black smoke formulations were identified in the small pellet testing to

  4. 7 CFR 3201.19 - Composite panels.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Fiberboard; Shower and Restroom Dividers; and Signage. USDA is requesting that manufacturers of these... dividers, and signage, and which product should be afforded the preference in purchasing. Note to paragraph... signage containing recovered materials as items for which Federal agencies must give preference in their...

  5. 7 CFR 3201.19 - Composite panels.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Fiberboard; Shower and Restroom Dividers; and Signage. USDA is requesting that manufacturers of these... dividers, and signage, and which product should be afforded the preference in purchasing. Note to paragraph... signage containing recovered materials as items for which Federal agencies must give preference in their...

  6. 7 CFR 3201.19 - Composite panels.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Fiberboard; Shower and Restroom Dividers; and Signage. USDA is requesting that manufacturers of these... dividers, and signage, and which product should be afforded the preference in purchasing. Note to paragraph... signage containing recovered materials as items for which Federal agencies must give preference in their...

  7. The Effects of Fiber Inclusion on Pet Food Sensory Characteristics and Palatability.

    PubMed

    Koppel, Kadri; Monti, Mariana; Gibson, Michael; Alavi, Sajid; Donfrancesco, Brizio Di; Carciofi, Aulus Cavalieri

    2015-02-16

    The objectives of this study were to determine (a) the influence of fiber on the sensory characteristics of dry dog foods; (b) differences of coated and uncoated kibbles for aroma and flavor characteristics; (c) palatability of these dry dog foods; and (d) potential associations between palatability and sensory attributes. A total of eight fiber treatments were manufactured: a control (no fiber addition), guava fiber (3%, 6%, and 12%), sugar cane fiber (9%; large and small particle size), and wheat bran fiber (32%; large and small particle size). The results indicated significant effects of fibers on both flavor and texture properties of the samples. Bitter taste and iron and stale aftertaste were examples of flavor attributes that differed with treatment, with highest intensity observed for 12% guava fiber and small particle size sugar cane fiber treatments. Fracturability and initial crispness attributes were lowest for the sugar cane fiber treatments. Flavor of all treatments changed after coating with a palatant, increasing in toasted, brothy, and grainy attributes. The coating also had a masking effect on aroma attributes such as stale, flavor attributes such as iron and bitter taste, and appearance attributes such as porosity. Palatability testing results indicated that the control treatment was preferred over the sugar cane or the wheat bran treatment. The treatment with large sugarcane fiber particles was preferred over the treatment with small particles, while both of the wheat bran treatments were eaten at a similar level. Descriptive sensory analysis data, especially textural attributes, were useful in pinpointing the underlying characteristics and were considered to be reasons that may influence palatability of dog foods manufactured with inclusion of different fibers.

  8. 75 FR 6167 - Notice of a Request for Extension of a Currently Approved Information Collection

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-08

    ... raw cane sugar under the tariff- rate quota (TRQ) into the United States. DATES: Comments on this... imports of raw cane sugar. Proper completion of the CQE is mandatory for those foreign governments that are eligible and elect to export raw cane sugar to the United States under the TRQ. Estimate of burden...

  9. 75 FR 22095 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-27

    ... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 200,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...

  10. 75 FR 38764 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-06

    ... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 300,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...

  11. 76 FR 20305 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2011 Raw Sugar Tariff...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-12

    ... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2011 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 325,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2011 raw sugar tariff-rate quota (TRQ) by...

  12. Green-cane harvested sugarcane crop residue decomposition as a function of temperature, soil moisture, and particle size

    USDA-ARS?s Scientific Manuscript database

    Sugarcane, a complex hybrid of Saccharum species, is grown on over 170,000 ha in the state of Louisiana. In 2016, the crop was worth $750 million US. Green-cane harvest, widely used in sugarcane producing countries, deposits up to 20 Mg ha-1 of crop residue annually. Green cane harvesting of sugarca...

  13. 21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION...-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may... microorganisms in cane-sugar and/or beet-sugar mills as specified in paragraph (b) of this section. (b) They are...

  14. How to manage sugar cane in the field and factory following damaging freezes

    USDA-ARS?s Scientific Manuscript database

    The exposure of sugar cane to damaging frosts occurs in approximately 25% of the sugar cane producing countries world-wide. A series of damaging freezes, -2.6, -3.3 and -2.1°C, occurred in Morocco on 4, 5 and 13 February 2012, respectively, only 2 weeks after the commencement of the harvest season....

  15. Fluoride bioaccumulation by hydroponic cultures of camellia (Camellia japonica spp.) and sugar cane (Saccharum officinarum spp.).

    PubMed

    Camarena-Rangel, Nancy; Rojas Velázquez, Angel Natanael; Santos-Díaz, María del Socorro

    2015-10-01

    The ability of hydroponic cultures of camellia and sugar cane adult plants to remove fluoride was investigated. Plants were grown in a 50% Steiner nutrient solution. After an adaptation period to hydroponic conditions, plants were exposed to different fluoride concentrations (0, 2.5, 5 and 10 mg L(-1)). Fluoride concentration in the culture medium and in tissues was measured. In sugar cane, fluoride was mainly located in roots, with 86% of it absorbed and 14% adsorbed. Sugar cane plants removed 1000-1200 mg fluoride kg(-1) dry weight. In camellia plants the highest fluoride concentration was found in leaf. Roots accumulated fluoride mainly through absorption, which was 2-5 times higher than adsorption. At the end of the experiment, fluoride accumulation in camellia plants was 1000-1400 mgk g(-1) dry weight. Estimated concentration factors revealed that fluoride bioaccumulation is 74-221-fold in camellia plants and 100-500-fold in sugar cane plants. Thus, the latter appear as a suitable candidate for removing fluoride from water due to their bioaccumulation capacity and vigorous growth rate; therefore, sugar cane might be used for phytoremediation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. "Candy cane syndrome:" an underappreciated cause of abdominal pain and nausea after Roux-en-Y gastric bypass surgery.

    PubMed

    Aryaie, Amir H; Fayezizadeh, Mojtaba; Wen, Yuxiang; Alshehri, Mohammed; Abbas, Mujjahid; Khaitan, Leena

    2017-09-01

    "Candy cane" syndrome (a blind afferent Roux limb at the gastrojejunostomy) has been implicated as a cause of abdominal pain, nausea, and emesis after Roux-n-Y gastric bypass (RYGB) but remains poorly described. To report that "candy cane" syndrome is real and can be treated effectively with revisional bariatric surgery SETTING: All patients underwent "candy cane" resection at University Hospitals of Cleveland. All patients who underwent resection of the "candy cane" between January 2011 and July 2015 were included. All had preoperative workup to identify "candy cane" syndrome. Demographic data; pre-, peri-, and postoperative symptoms; data regarding hospitalization; and postoperative weight loss were assessed through retrospective chart review. Data were analyzed using Student's t test and χ 2 analysis where appropriate. Nineteen patients had resection of the "candy cane" (94% female, mean age 50±11 yr), within 3 to 11 years after initial RYGB. Primary presenting symptoms were epigastric abdominal pain (68%) and nausea/vomiting (32%), particularly with fibrous foods and meats. On upper gastrointestinal study and endoscopy, the afferent blind limb was the most direct outlet from the gastrojejunostomy. Only patients with these preoperative findings were deemed to have "candy cane" syndrome. Eighteen (94%) cases were completed laparoscopically. Length of the "candy cane" ranged from 3 to 22 cm. Median length of stay was 1 day. After resection, 18 (94%) patients had complete resolution of their symptoms (P<.001). Mean body mass index decreased from 33.9±6.1 kg/m 2 preoperatively to 31.7±5.6 kg/m 2 at 6 months (17.4% excess weight loss) and 30.5±6.9 kg/m 2 at 1 year (25.7% excess weight loss). The average length of latest follow-up was 20.7 months. "Candy cane" syndrome is a real phenomenon that can be managed safely with excellent outcomes with resection of the blind afferent limb. A thorough diagnostic workup is paramount to proper identification of this syndrome. Surgeons should minimize the size of the blind afferent loop left at the time of initial RYGB. Copyright © 2017 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.

  17. Lignocellulose-derived thin stillage composition and efficient biological treatment with a high-rate hybrid anaerobic bioreactor system.

    PubMed

    Oosterkamp, Margreet J; Méndez-García, Celia; Kim, Chang-H; Bauer, Stefan; Ibáñez, Ana B; Zimmerman, Sabrina; Hong, Pei-Ying; Cann, Isaac K; Mackie, Roderick I

    2016-01-01

    This study aims to chemically characterize thin stillage derived from lignocellulosic biomass distillation residues in terms of organic strength, nutrient, and mineral content. The feasibility of performing anaerobic digestion on these stillages at mesophilic (40 °C) and thermophilic (55 °C) temperatures to produce methane was demonstrated. The microbial communities involved were further characterized. Energy and sugar cane stillage have a high chemical oxygen demand (COD of 43 and 30 g/L, respectively) and low pH (pH 4.3). Furthermore, the acetate concentration in sugar cane stillage was high (45 mM) but was not detected in energy cane stillage. There was also a high amount of lactate in both types of stillage (35-37 mM). The amount of sugars was 200 times higher in energy cane stillage compared to sugar cane stillage. Although there was a high concentration of sulfate (18 and 23 mM in sugar and energy cane stillage, respectively), both thin stillages were efficiently digested anaerobically with high COD removal under mesophilic and thermophilic temperature conditions and with an organic loading rate of 15-21 g COD/L/d. The methane production rate was 0.2 L/g COD, with a methane percentage of 60 and 64, and 92 and 94 % soluble COD removed, respectively, by the mesophilic and thermophilic reactors. Although both treatment processes were equally efficient, there were different microbial communities involved possibly arising from the differences in the composition of energy cane and sugar cane stillage. There was more acetic acid in sugar cane stillage which may have promoted the occurrence of aceticlastic methanogens to perform a direct conversion of acetate to methane in reactors treating sugar cane stillage. Results showed that thin stillage contains easily degradable compounds suitable for anaerobic digestion and that hybrid reactors can efficiently convert thin stillage to methane under mesophilic and thermophilic conditions. Furthermore, we found that optimal conditions for biological treatment of thin stillage were similar for both mesophilic and thermophilic reactors. Bar-coded pyrosequencing of the 16S rRNA gene identified different microbial communities in mesophilic and thermophilic reactors and these differences in the microbial communities could be linked to the composition of the thin stillage.

  18. Activated carbon and biochar from agricultural by-products in the adorption of Cd, Pb and Zn under laboratory conditions

    NASA Astrophysics Data System (ADS)

    Coscione, Aline; Zini, Barbara

    2015-04-01

    The immobilization of inorganic contaminants by using biochar in soils has played an increasingly important role and it is seen as an attractive alternative for the remediation of heavy metals. Although, the production of activated carbon (CA) from agricultural by-products has received special attention, the activation of the the organic source has been studied in order to increase its porposity, surface area and chemical polarity, resulting in higher adsorption of metals. Therefore, this study aimed to evaluate the effectiveness of BC and CA samples, obtained from a eucalyptus husks and cane sugar bagasse after activation with 20% phosphoric acid and pyrolyzed at 450oC in the retention of Zn, Cd and Pb using contaminated individual solutions. The experiment was performed using samples of activated carbon of eucalyptus husk (CCA), eucalyptus husk biochar (BC), activated carbon of sugar cane bagasse (CBA) and sugar cane bagasse biochar (BB), treated with Zn, Cd (range of tested solution from 0.1 up to 12 mmol L-1) and Pb (from 0.1 up 50 mmol L-1) and the adjustemento of Langmuir adsorption isotherms. Samples obtained from bagasse presented higher adsoprtion of the metals tested then eucalyptus. Also the activation process had not the expected effect on either eucalyptus and bagasse samples The maxmum adsorption capacyty of samples were as follws, in mmol g-1: for Cd - 0.36 for BC; 0.32 for CCA; 0.40 for BB; 0.31 for CBA. For Zn- 0.14 for BC; no adsorbed by CCA; 0.35 5 for BB; 0.06 for CBA. For Pb - 1.24 for BC; 0.40 for CCA; 0,45 for BB; 0,03 for CBA. However, it was also observed that due to the activation with phosphoric acid, the pH of the activated carbon (CCA and CBA) were 2.4 and 2.5 in comparison with the biochars not activated (BC and BB) 9.7 and 7.0 respectively. Thus, it is yet not possible to state if the calculate capacity is due exclusively to the complexation of chemical groups in the surface of samples or to which extent there is a contribution of precipitation caused by the basic pH (non-activated) biochar samples, as shown for Zn and Pb.

  19. Comparison of metabolic cost and cardiovascular response to stair ascending and descending with walkers and canes in older adults.

    PubMed

    Foley, Michael; Bowen, Brett

    2014-09-01

    To compare oxygen cost (mL·kg(-1)·m(-1)) and cardiovascular response (beats/m) and oxygen consumption (mL·kg(-1)·min(-1)) and heart rate (beats/min) to stair ascending and descending with walkers, with canes, and without assistive devices (ADs) in older adults. Descriptive, repeated measures. Indoor stairway. Convenience sample of able-bodied volunteers, non-AD users (N=14; mean age, 63.71 ± 11.7 y; mean body mass, 72.7 ± 14.1 kg; mean height, 165.7 ± 9.2 cm). Participants performed 4 randomized trials of stair ascending and descending at their own self-selected speed with 3 ADs: single-point cane, standard walker (SW), and wheeled walker (WW). They also performed unassisted stair ascending and descending. Each trial consisted of a 5-minute steady-state session followed by a 2-minute data collection period. Steady-state expired ventilations were collected in Douglas bags for metabolic analysis. Oxygen cost (mL·kg(-1)·m(-1)), heart rate (HR) response (beats/m), oxygen consumption (mL·kg(-1)·min(-1)), and HR (beats/min) were compared for each trial of stair ascending and descending using analysis of variance repeated measures (P<.05). Greater oxygen cost (per meter) was found for stair ascending and descending using the single-point cane (121%), SW (217%), and WW (232%) compared with unassisted stair ascending and descending (P<.05). Increased HR response (per meter) was found for stair ascending and descending using the single-point cane (116%), SW (126%), and WW (147%) compared with unassisted stair ascending and descending (P<.05). However, oxygen consumption (per minute) and HR (per minute) were not significantly increased during stair ascending and descending with the ADs compared with unassisted stair ascending and descending. Participants stair ascended and descended at significantly (P<.05) reduced speeds during trials with the ADs. This research should aid clinicians by providing evidence to base recommendations on regarding AD usage when encountering stairs during home and community ambulation. Copyright © 2014 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  20. HDP for the Neutralized pH Value Control in the Clarifying Process of Sugar Cane Juice

    NASA Astrophysics Data System (ADS)

    Lin, Xiaofeng; Yang, Jiaran

    2009-05-01

    Neutralizing pH value of sugar cane juice is the important craft in the control process in the clarifying process of sugar cane juice, which is the important factor to influence output and the quality of white sugar. On the one hand, it is an important content to control the neutralized pH value within a required range, which has the vital significance for acquiring high quality purified juice, reducing energy consumption and raising sucrose recovery. On the other hand, it is a complicated physical-chemistry process, which has the characteristics of strong non-linearity, time-varying, large time-delay, and multi-input. Therefore, there has not been a very good solution to control the neutralized pH value. Firstly, in this chapter, a neural network model for the clarifying process of sugar juice is established based on gathering 1200 groups of real-time sample data in a sugar factory. Then, the HDP (Heuristic Dynamic Programming) method is used to optimize and control the neutralized pH value in the clarifying process of sugar juice. Simulation results indicate that this method has good control effect. This will build a good foundation for stabilizing the clarifying process and enhancing the quality of the purified juice and lastly enhancing the quality of white sugar.

  1. Horizontal drilling potential of the Cane Creek Shale, Paradox Formation, Utah

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Morgan, C.D.; Chidsey, T.C.

    1991-06-01

    The Cane Creek shale of the Pennsylvanian Paradox Formation is a well-defined target for horizontal drilling. This unit is naturally fractures and consists of organic-rich marine shale with interbedded dolomitic siltstone and anhydrite. Six fields have produced oil from the Cane Creek shale in the Paradox basin fold-and-fault belt. The regional structural trend is north-northwest with productive fractures occurring along the crest and flanks of both the larger and more subtle smaller anticlines. The Long Canyon, Cane Creek, Bartlett Flat, and Shafer Canyon fields are located on large anticlines, while Lion Mesa and Wilson Canyon fields produce from subtle structuralmore » noses. The Cane Creek shale is similar to the highly productive Bakken Shale in the Williston basin. Both are (1) proven producers of high-gravity oil, (2) highly fractured organic-rich source rocks, (3) overpressured, (4) regionally extensive, and (5) solution-gas driven with little or no associated water. Even though all production from the Cane Creek shale has been from conventional vertical wells, the Long Canyon 1 well has produced nearly 1 million bbl of high-gravity, low-sulfur oil. Horizontal drilling may result in the development of new fields, enhance recovery in producing fields, and revive production in abandoned fields. In addition, several other regionally extensive organic-rich shale beds occur in the Paradox Formation. The Gothic and Chimney Rock shales for example, offer additional potential lying above the Cane Creek shale.« less

  2. Case-control study of lung cancer among sugar cane farmers in India

    PubMed Central

    Amre, D. K.; Infante-Rivard, C.; Dufresne, A.; Durgawale, P. M.; Ernst, P.

    1999-01-01

    OBJECTIVES: To investigate the risk of lung cancer among sugar cane farmers and sugar mill workers. METHODS: A case-control study was conducted based in six hospitals in the predominantly sugar cane farming districts of the province of Maharashtra in India. Newly diagnosed, histologically confirmed cases were identified from these hospitals between May 1996 and April 1998. Other cancers were chosen as controls and matched to cases by age, sex, district of residence, and timing of diagnosis. RESULTS: Adjusting for confounders, an increased risk of lung cancer was found for workers ever employed on a sugar cane farm (odds ratio (OR) 1.92, 95% confidence interval (95% CI) 1.08 to 3.40). Increased risks were found for work involving preparation of the farm (OR 1.81, 95% CI 0.99 to 3.27) and burning of the farm after harvesting (OR 1.82, 95% CI 0.99 to 3.34). Non-significant increases in risks were found for harvesting the crop (OR 1.41, 95% CI 0.70 to 2.90) and processing the cane in the mills (OR 1.70, 95% CI 0.20 to 12.60). CONCLUSIONS: Exposure to fibres of biogenic amorphous silica (BAS) formed from silica absorbed from the soil and deposited in the leaves of the sugar cane crop or crystalline silica formed as a result of conversion of BAS to cristobalite at high temperatures may account for the increased risks of lung cancer among sugar cane farmers.   PMID:10492653

  3. Transmission of Guanarito and Pirital Viruses among Wild Rodents, Venezuela

    PubMed Central

    Milazzo, Mary L.; Cajimat, Maria N.B.; Duno, Gloria; Duno, Freddy; Utrera, Antonio

    2011-01-01

    Samples from rodents captured on a farm in Venezuela in February 1997 were tested for arenavirus, antibody against Guanarito virus (GTOV), and antibody against Pirital virus (PIRV). Thirty-one (48.4%) of 64 short-tailed cane mice (Zygodontomys brevicauda) were infected with GTOV, 1 Alston’s cotton rat (Sigmodon alstoni) was infected with GTOV, and 36 (64.3%) of 56 other Alston’s cotton rats were infected with PIRV. The results of analyses of field and laboratory data suggested that horizontal transmission is the dominant mode of GTOV transmission in Z. brevicauda mice and that vertical transmission is an important mode of PIRV transmission in S. alstoni rats. The results also suggested that bodily secretions and excretions from most GTOV-infected short-tailed cane mice and most PIRV-infected Alston’s cotton rats may transmit the viruses to humans. PMID:22172205

  4. Comparison of three dielectric barrier discharges regarding their physical characteristics and influence on the adhesion properties on maple, high density fiberboards and wood plastic composite

    NASA Astrophysics Data System (ADS)

    Peters, F.; Hünnekens, B.; Wieneke, S.; Militz, H.; Ohms, G.; Viöl, W.

    2017-11-01

    In this study, three different dielectric barrier discharges, based on the same setup and run with the same power supply, are characterized by emission spectroscopy with regards to the reduced electrical field strength, and the rotational, vibrational and electron temperature. To compare discharges common for the treatment on wood, a coplanar surface barrier discharge, a direct dielectric barrier discharge and a jet system/remote plasma are chosen. To minimize influences due to the setups or power, the discharges are realized with the same electrodes and power supply and normalized to the same power. To evaluate the efficiency of the different discharges and the influence on treated materials, the surface free energy is determined on a maple wood, high density fiberboard and wood plastic composite. The influence is measured depending on the treatment time, with the highest impact in the time of 5 s.

  5. Mechanical and water soaking properties of medium density fiberboard with wood fiber and soybean protein adhesive.

    PubMed

    Li, Xin; Li, Yonghui; Zhong, Zhikai; Wang, Donghai; Ratto, Jo A; Sheng, Kuichuan; Sun, Xiuzhi Susan

    2009-07-01

    Soybean protein is a renewable and abundant material that offers an alternative to formaldehyde-based resins. In this study, soybean protein was modified with sodium dodecyl sulfate (SDS) as an adhesive for wood fiber medium density fiberboard (MDF) preparation. Second-order response surface regression models were used to study the effects and interactions of initial moisture content (IMC) of coated wood fiber, press time (PT) and temperature on mechanical and water soaking properties of MDF. Results showed that IMC of coated fiber was the dominant influencing factor. Mechanical and soaking properties improved as IMC increased and reached their highest point at an IMC of 35%. Press time and temperature also had a significant effect on mechanical and water soaking properties of MDF. Second-order regression results showed that there were strong relationships between mechanical and soaking properties of MDF and processing parameters. Properties of MDF made using soybean protein adhesive are similar to those of commercial board.

  6. Radiated Sound Power from a Curved Honeycomb Panel

    NASA Technical Reports Server (NTRS)

    Robinson, Jay H.; Buehrle, Ralph D.; Klos, Jacob; Grosveld, Ferdinand W.

    2003-01-01

    The validation of finite element and boundary element model for the vibro-acoustic response of a curved honeycomb core composite aircraft panel is completed. The finite element and boundary element models were previously validated separately. This validation process was hampered significantly by the method in which the panel was installed in the test facility. The fixture used was made primarily of fiberboard and the panel was held in a groove in the fiberboard by a compression fitting made of plastic tubing. The validated model is intended to be used to evaluate noise reduction concepts from both an experimental and analytic basis simultaneously. An initial parametric study of the influence of core thickness on the radiated sound power from this panel, using this numerical model was subsequently conducted. This study was significantly influenced by the presence of strong boundary condition effects but indicated that the radiated sound power from this panel was insensitive to core thickness primarily due to the offsetting effects of added mass and added stiffness in the frequency range investigated.

  7. 78 FR 56646 - Determination of Total Amounts of Fiscal Year 2014 WTO Tariff-Rate Quotas for Raw Cane Sugar and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-13

    ... Secretary Determination of Total Amounts of Fiscal Year 2014 WTO Tariff- Rate Quotas for Raw Cane Sugar and... the Fiscal Year (FY) 2014 (October 1, 2013-September 30, 2014) in-quota aggregate quantity of raw cane sugar at 1,117,195 metric tons raw value (MTRV). The Secretary also announces the establishment of the...

  8. 75 FR 47258 - Determination of Total Amounts of Fiscal Year 2011 Tariff-Rate Quotas for Raw Cane Sugar and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-05

    ... Determination of Total Amounts of Fiscal Year 2011 Tariff-Rate Quotas for Raw Cane Sugar and Certain Sugars...) 2011 in-quota aggregate quantity of the raw, as well as, refined and specialty sugar Tariff-Rate Quotas (TRQ) as required under the U.S. World Trade Organization (WTO) commitments. The FY 2011 raw cane sugar...

  9. 77 FR 55451 - Determination of Total Amounts of Fiscal Year 2013 Tariff-Rate Quotas for Raw Cane Sugar and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-10

    ... Secretary Determination of Total Amounts of Fiscal Year 2013 Tariff-Rate Quotas for Raw Cane Sugar and...) 2013 (October 1, 2012-September 30, 2013) in-quota aggregate quantity of the raw, as well as, refined and specialty sugar Tariff-Rate Quotas (TRQ). The FY 2013 raw cane sugar TRQ is established at 1,117...

  10. Interdisciplinary Collaboration in the Choice of an Adapted Mobility Device for a Child with Cerebral Palsy and Visual Impairment.

    ERIC Educational Resources Information Center

    Glanzman, Allan; Ducret, Walter

    2003-01-01

    To select an adapted mobility device for a 5-year-old boy with blindness and spastic diplegic cerebral palsy, a multidisciplinary team used 8-millimeter videography to evaluate the subject's joint angle during ambulation with one of three canes and with no cane. The I-style cane provided optimal posture and gait pattern. (Contains references.) (CR)

  11. Effect of sugarcane ripener glyphosate (Roundup PowerMAX® II) on growth and biomass characteristics of energy cane

    USDA-ARS?s Scientific Manuscript database

    Energy cane is considered as one of the most promising feedstock for the emerging bioenergy industry. A random set of 42 energy cane clones bred by the USDA-ARS Sugarcane Research Unit at Houma, LA were taken from a second clonal stage trial and evaluated during 2015-16 at the LSU AgCenter’s Sugar R...

  12. Next Generation Enterprise Network Business Continuity: Maintaining Operations In A Compromised Environment

    DTIC Science & Technology

    2016-03-01

    analysis CANES Consolidated Afloat Network and Enterprise Services CIA confidentiality, integrity, availability COOP continuity of operations DMZ...exercises, and increased readiness at sea as CANES is deployed to the Fleet. G. METHODS This work reviews published literature on BC, disaster recovery (DR...mitigation efforts [33]. 5. Consolidated Afloat Networks and Enterprise Services Consolidated Afloat Networks and Enterprise Services ( CANES ) is not

  13. A cane reduces loss of balance in patients with peripheral neuropathy: results from a challenging unipedal balance test.

    PubMed

    Ashton-Miller, J A; Yeh, M W; Richardson, J K; Galloway, T

    1996-05-01

    To test the hypothesis that use of a cane in the nondominant hand during challenging balance tasks would significantly decrease loss of balance in patients with peripheral neuropathy while transferring from bipedal to unipedal stance on an unsteady surface. Nonrandomized control study. Tertiary-care institution. Eight consecutive patients with peripheral neuropathy (PN) and eight age- and gender-matched controls (C) with a mean (SD) age of 65 (8.2) years. Subjects were asked to transfer their weight onto their right foot, despite a rapid +/- 2 degrees or +/- 4 degrees frontal plane tilt of the support surface at 70% of weight transfer, and balance unipedally for at least 3 seconds. The efficacy of their weight transfer was evaluated over 112 consecutive randomized and blocked trials by calculating loss of balance as failure rates (%FR) with and without visual feedback, and with and without use of a cane in the nondominant (left) hand. Results were analyzed using a 2 x 2 x 2 x 2 x 2 repeated-measures analysis of variance (rm-ANOVA) and post hoc t tests. The rm-ANOVA showed that the FR of the PN subjects (47.6% [18.1%]) was significantly higher than C (29.2% [15.2%], p = .036). Removing visual feedback, simulating the dark of night, increased the FR fourfold (p = .000). Use of a cane in the contralateral nondominant hand significantly reduced the FR (p = .000), particularly in the PN group (cane x disease interaction: p = .055). Post hoc t tests showed that with or without visual feedback, the cane reduced the FR of the PN group fourfold and enabled them to perform more reliably than matched controls not using a cane (p = .011). An inversion perturbation resulted in a higher FR than an eversion perturbation (p = .007). The PN group employed larger mean peak cane forces (21.9% BW) than C (13.6% BW) in restoring their balance (p = .000). Use of a cane by PN patients significantly reduced their risk of losing balance on unstable surfaces, especially under low-light conditions.

  14. Cherish the Capacity to Change

    PubMed Central

    Wearn, Joseph T.

    1967-01-01

    The following address was given at the Gold-Headed Cane Ceremony, University of California School of Medicine, on 3 June 1966. At this event on the eve of Commencement Day, the senior student who has been chosen by his classmates and professors in the Department of Medicine as the one who best exemplifies the qualities of a true physician is given a gold-headed cane. This carries on the English tradition of a cane which was passed from physician to physician from 1689 to 1825, and was carried successively by Drs. John Radcliffe, Richard Mead, Anthony Askew, David Pitcairn and Matthew Baillie. The original cane now rests in the Hall of the Royal College of Physicians in London. PMID:4859813

  15. Combination of sugar analysis and stable isotope ratio mass spectrometry to detect the use of artificial sugars in royal jelly production.

    PubMed

    Wytrychowski, Marine; Daniele, Gaëlle; Casabianca, Hervé

    2012-05-01

    The effects of feeding bees artificial sugars and/or proteins on the sugar compositions and (13)C isotopic measurements of royal jellies (RJs) were evaluated. The sugars fed to the bees were two C4 sugars (cane sugar and maize hydrolysate), two C3 sugars (sugar beet, cereal starch hydrolysate), and honey. The proteins fed to them were pollen, soybean, and yeast powder proteins. To evaluate the influence of the sugar and/or protein feeding over time, samples were collected during six consecutive harvests. (13)C isotopic ratio measurements of natural RJs gave values of around -25 ‰, which were also seen for RJs obtained when the bees were fed honey or C3 sugars. However, the RJs obtained when the bees were fed cane sugar or corn hydrolysate (regardless of whether they were also fed proteins) gave values of up to -17 ‰. Sugar content analysis revealed that the composition of maltose, maltotriose, sucrose, and erlose varied significantly over time in accordance with the composition of the syrup fed to the bees. When corn and cereal starch hydrolysates were fed to the bees, the maltose and maltotriose contents of the RJs increased up to 5.0 and 1.3 %, respectively, compared to the levels seen in authentic samples (i.e., samples obtained when the bees were fed natural food: honey and pollen) that were inferior to 0.2% and not detected, respectively. The sucrose and erlose contents of natural RJs were around 0.2 %, whereas those in RJs obtained when the bees were fed cane or beet sugar were as much as 4.0 and 1.3 %, respectively. The combination of sugar analysis and (13)C isotopic ratio measurements represents a very efficient analytical methodology for detecting (from early harvests onward) the use of C4 and C3 artificial sugars in the production of RJ.

  16. 49 CFR 178.980 - Stacking test.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

  17. 49 CFR 178.980 - Stacking test.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

  18. 27 CFR 20.145 - Encased containers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Encased containers. 20.145... Denatured Alcohol § 20.145 Encased containers. Completely denatured alcohol may be packaged by distributors in unlabeled containers which are completely encased in wood, fiberboard, or similar material so that...

  19. 49 CFR 178.609 - Test requirements for packagings for infectious substances.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... paragraph (c), which, for test purposes, categorizes packagings according to their material characteristics... performance may be rapidly affected by moisture; plastics that may embrittle at low temperature; and other... the appropriate test. Table I—Tests Required Material of Outer packaging Fiberboard Plastics Other...

  20. Ergonomics productivity enhancement at government-owned sugar cane factories in east Java, Indonesia.

    PubMed

    Manuaba, A

    1995-06-01

    To cope, both with the increasing demand for sugar and to win the global competition as well, government-owned sugar cane limited number xxi-xxii, has decided to enhance its productivity, among other things, by implementing ergonomics principles within their factories. In the execution, ergonomics application have been carried out since 1992, which resulted in safer, healthier, and more efficient working conditions and environment. Some of the improvements yielded economic gains through higher productivity via increased output, lower cost, faster processing, etc. Improvements related to cane transloading and unloading processes resulted in a higher amount of cane being transferred from the trucks to the lorries as well as from the lorries to the cane table. Fewer clinical visits, lower health care costs, more efficient inspection, and fewer fatigue complaints are also achieved by improvement steps, which increase the productivity as end results. With all those economic gains, full and long lasting management's concern and commitment could be created without a doubt.

  1. The Effect of the Color of a Long Cane Used by Individuals Who Are Visually Impaired on the Yielding Behavior of Drivers

    ERIC Educational Resources Information Center

    Bourquin, Eugene A.; Emerson, Robert Wall; Sauerburger, Dona; Barlow, Janet

    2017-01-01

    Introduction: A new market trend offers long canes for individuals with visual impairments in a variety of colors; however, the impact of these colors is unknown to orientation and mobility (O&M) specialists and individuals who are blind or who have low vision. The authors examined the impact of cane color on drivers' yielding behaviors; also,…

  2. Cultivar evaluation and essential test locations identification for sugarcane breeding in China.

    PubMed

    Luo, Jun; Pan, Yong-Bao; Xu, Liping; Zhang, Hua; Yuan, Zhaonian; Deng, Zuhu; Chen, Rukai; Que, Youxiong

    2014-01-01

    The discrepancies across test sites and years, along with the interaction between cultivar and environment, make it difficult to accurately evaluate the differences of the sugarcane cultivars. Using a genotype main effect plus genotype-environment interaction (GGE) Biplot software, the yield performance data of seven sugarcane cultivars in the 8th Chinese National Sugarcane Regional Tests were analyzed to identify cultivars recommended for commercial release. Fn38 produced a high and stable sugar yield. Gn02-70 had the lowest cane yield with high stability. Yz06-407 was a high cane yield cultivar with poor stability in sugar yield. Yz05-51 and Lc03-1137 had an unstable cane yield but relatively high sugar yield. Fn39 produced stable high sugar yield with low and unstable cane production. Significantly different sugar and cane yields were observed across seasons due to strong cultivar-environment interactions. Three areas, Guangxi Chongzuo, Guangxi Baise, and Guangxi Hechi, showed better representativeness of cane yield and sugar content than the other four areas. On the other hand, the areas Guangxi Chongzuo, Yunnan Lincang, and Yunnan Baoshan showed strong discrimination ability, while the areas Guangxi Hechi and Guangxi Liuzhou showed poor discrimination ability. This study provides a reference for cultivar evaluation and essential test locations identification for sugarcane breeding in China.

  3. Evolutionary Responses to Invasion: Cane Toad Sympatric Fish Show Enhanced Avoidance Learning

    PubMed Central

    Caller, Georgina; Brown, Culum

    2013-01-01

    The introduced cane toad (Bufo marinus) poses a major threat to biodiversity due to its lifelong toxicity. Several terrestrial native Australian vertebrates are adapting to the cane toad’s presence and lab trials have demonstrated that repeated exposure to B. marinus can result in learnt avoidance behaviour. Here we investigated whether aversion learning is occurring in aquatic ecosystems by comparing cane toad naïve and sympatric populations of crimson spotted rainbow fish (Melanotaenia duboulayi). The first experiment indicated that fish from the sympatric population had pre-existing aversion to attacking cane toad tadpoles but also showed reduced attacks on native tadpoles. The second experiment revealed that fish from both naïve and sympatric populations learned to avoid cane toad tadpoles following repeated, direct exposure. Allopatric fish also developed a general aversion to tadpoles. The aversion learning abilities of both groups was examined using an experiment involving novel distasteful prey items. While both populations developed a general avoidance of edible pellets in the presence of distasteful pellets, only the sympatric population significantly reduced the number of attacks on the novel distasteful prey item. These results indicate that experience with toxic prey items over multiple generations can enhance avoidance leaning capabilities via natural selection. PMID:23372788

  4. Cultivar Evaluation and Essential Test Locations Identification for Sugarcane Breeding in China

    PubMed Central

    Luo, Jun; Xu, Liping; Zhang, Hua; Yuan, Zhaonian; Deng, Zuhu; Chen, Rukai

    2014-01-01

    The discrepancies across test sites and years, along with the interaction between cultivar and environment, make it difficult to accurately evaluate the differences of the sugarcane cultivars. Using a genotype main effect plus genotype-environment interaction (GGE) Biplot software, the yield performance data of seven sugarcane cultivars in the 8th Chinese National Sugarcane Regional Tests were analyzed to identify cultivars recommended for commercial release. Fn38 produced a high and stable sugar yield. Gn02-70 had the lowest cane yield with high stability. Yz06-407 was a high cane yield cultivar with poor stability in sugar yield. Yz05-51 and Lc03-1137 had an unstable cane yield but relatively high sugar yield. Fn39 produced stable high sugar yield with low and unstable cane production. Significantly different sugar and cane yields were observed across seasons due to strong cultivar-environment interactions. Three areas, Guangxi Chongzuo, Guangxi Baise, and Guangxi Hechi, showed better representativeness of cane yield and sugar content than the other four areas. On the other hand, the areas Guangxi Chongzuo, Yunnan Lincang, and Yunnan Baoshan showed strong discrimination ability, while the areas Guangxi Hechi and Guangxi Liuzhou showed poor discrimination ability. This study provides a reference for cultivar evaluation and essential test locations identification for sugarcane breeding in China. PMID:24982939

  5. Sediment-transport characteristics of Cane Creek, Lauderdale County, Tennessee

    USGS Publications Warehouse

    Carey, W.P.

    1993-01-01

    An investigation of the sediment-transport characteristics of Cane Creek in Lauderdale County, Tennessee, was conducted from 1985-88 to evaluate the potential for channel erosion induced by modifications (realignment and enlargement) and the potential ability of different flows to move bed and bank stabilizing material. Frequently occurring flows in Cane Creek are capable of moving sand-size material (0.0625 - 4.0 millimeters). During floods that equal or exceed the 2-year flood, Cane Creek is capable of moving very coarse gravel (32 - 64 millimeters). Boundary-shear values at bridges, where flow contractions occur, correspond to critical diameters in excess of 100 millimeters. Thus, the areas near bridges, where channel stability is most critical, are the areas where erosive power is greatest. Deepening and widening of Cane Creek has exposed large areas of channel boundary that are a significant source of raindrop-detached sediment during the early stages of a storm before stream flow increases signifi- cantly. This causes suspended-sediment concentration to peak while the flow hydrograph is just beginning to rise. For basins like Cane Creek, where runoff events commonly last less than a day and where variation in discharge and sediment concentrations are large, an estimate of sediment yield based on periodic observations of instantaneous values is subject to considerable uncertainty.

  6. Seasonal hydroclimatic impacts of Brazilian sugar cane expansion

    NASA Astrophysics Data System (ADS)

    Georgescu, M.; Lobell, D. B.; Field, C. B.; Mahalov, A.

    2012-12-01

    Brazil is the leading producer of sugar cane in the world with roughly half used for ethanol production. Because of suitable climatic growing conditions, the majority of biofuel production is derived from sugar plantations in southeastern states. Anticipated increases in global demand for biofuels are expected to lead to future sugar cane expansion extending into Brazilian pasturelands and native cerrado. Prior to undergoing large-scale expansion an evaluation of impacts on the region's hydroclimate is warranted. Using a suite of multi-year ensemble-based simulations with the WRF modeling system, we quantify hydroclimatic consequences of sugar cane expansion across portions of south-central Brazil. Conversion from current land use to sugar cane causes opposing seasonal impacts on near-surface temperature. Proggresively greater cooling is simulated during the course of the growing season, followed by an abrupt warming shift post-harvest. Although seasonal impacts on near-surface temperature are significant, with cooling of 1C occurring during the peak of the growing season followed by warming of similar magnitude, impacts are small when annually averaged. Ensemble mean differences between the imposed sugar cane expansion and non-expansion scenario are suggestive of a drying precipitation trend, yet large uncertainty among individual members precludes definitive statements about impacts on the region's rainfall.

  7. Can use of walkers or canes impede lateral compensatory stepping movements?

    PubMed

    Bateni, Hamid; Heung, Evelyn; Zettel, John; McLlroy, William E; Maki, Brian E

    2004-08-01

    Although assistive devices, such as walkers and canes are often prescribed to aid in balance control, recent studies have suggested that such devices may actually increase risk of falling. In this study, we investigated one possible mechanism: the potential for walkers or canes to interfere with, or constrain, lateral movement of the feet and thereby impede execution of compensatory stepping reactions during lateral loss of balance. Lateral stepping reactions were evoked, in 10 healthy young adults (ages 22-27 years), by means of sudden unpredictable medio-lateral support surface translation. Subjects were tested while holding and loading a standard pickup walker or single-tip cane or while using no assistive device (hands free or holding an object). Results supported the hypothesis that using a walker or cane can interfere with compensatory stepping. Collisions between the swing-foot and mobility aid were remarkably frequent when using the walker (60% of stepping reactions) and also occurred in cane trials (11% of stepping reactions). Furthermore, such collisions were associated with a significant reduction (26-37%) in lateral step length. It appeared that subjects were sometimes able to avoid collision by increasing the forward or backward displacement of the swing-foot or by moving the cane; however, attempts to lift the walker out of the way occurred rarely and were usually impeded due to collision between the contralateral walker post and stance foot. The fact that compensatory stepping behavior was altered significantly in such a healthy cohort clearly demonstrates some of the safety limitations inherent to these assistive devices, as currently designed. Copyright 2003 Elsevier B.V.

  8. A new primary mobility tool for the visually impaired: A white cane-adaptive mobility device hybrid.

    PubMed

    Rizzo, John-Ross; Conti, Kyle; Thomas, Teena; Hudson, Todd E; Wall Emerson, Robert; Kim, Dae Shik

    2017-05-16

    This article describes pilot testing of an adaptive mobility device-hybrid (AMD-H) combining properties of two primary mobility tools for people who are blind: the long cane and adaptive mobility devices (AMDs). The long cane is the primary mobility tool used by people who are blind and visually impaired for independent and safe mobility and AMDs are adaptive devices that are often lightweight frames approximately body width in lateral dimension that are simply pushed forward to clear the space in front of a person. The prototype cane built for this study had a wing apparatus that could be folded around the shaft of a cane but when unfolded, deployed two wheeled wings 25 cm (9.8 in) to each side of the canetip. This project explored drop-off and obstacle detection for 6 adults with visual impairment using the deployed AMD-H and a standard long cane. The AMD-H improved obstacle detection overall, and was most effective for the smallest obstacles (2 and 6 inch diameter). The AMD-H cut the average drop off threshold from 1.79 inches (4.55 cm) to .96 inches (2.44 cm). All participants showed a decrease in drop off detection threshold and an increase in detection rate (13.9% overall). For drop offs of 1 in (2.54 cm) and 3 in (7.62 cm), all participants showed large improvements with the AMD-H, ranging from 8.4 to 50%. The larger drop offs of 5 in (12.7 cm) and 7 in (17.8 cm) were well detected by both types of canes.

  9. Design and Installation of Irrigation System for the Expansion of Sugar cane- Industries in Ahvaz, IRAN.

    NASA Astrophysics Data System (ADS)

    Afshari, E.; Afshari, S.

    2005-12-01

    This paper presents achievements of a twelve years ongoing project expansion of sugar cane- industries as a major agricultural development in Ahvaz, IRAN. The entire project is divided in to seven units and each unit provides irrigation water for 30,000 acres of sugar cane farms in Ahwaz. Absou Inc. is one of the consulting firms that is in charge of design and overseeing installation of irrigation system as well as the development of lands for sugar-cane cultivation at one of the units, called Farabi unit .In general, the mission of project is to Pump fresh water from Karoon River and direct it to the sugar cane farm for irrigation. In particular, the task of design and installation include, (1) build a pumping station at Karoon River with capacity of 1271 ft3/sec, (2) transfer water by main channel from Karoon rive to the farm site 19 miles (3) install a secondary pumping stations which direct water from main channel to drainage pipes and provides water for local farms (4) build a secondary channels which carries water with pipe lines with total length of 42 miles and diameter of 16 to 32 inch. (5) install drainage pump stations and collectors (6) level the ground surface and prepare it for irrigation (7) build railroad for carrying sugar canes (23 miles). Thus far, more than 15,000 acres of farm in Farabi unit is under sugar cane cultivation. The presentation will illustrate more details about different aspects of the project including design, installation and construction phases.

  10. Fast pyrolysis of tropical biomass species and influence of water pretreatment on product distributions

    DOE PAGES

    Morgan, Trevor James; Turn, Scott Q.; Sun, Ning; ...

    2016-03-15

    Here, the fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amountmore » of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO 2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO 2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.« less

  11. Fast pyrolysis of tropical biomass species and influence of water pretreatment on product distributions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Morgan, Trevor James; Turn, Scott Q.; Sun, Ning

    Here, the fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amountmore » of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO 2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO 2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.« less

  12. Fast Pyrolysis of Tropical Biomass Species and Influence of Water Pretreatment on Product Distributions

    PubMed Central

    Morgan, Trevor James; Turn, Scott Q.; Sun, Ning; George, Anthe

    2016-01-01

    The fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amount of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena. PMID:26978265

  13. Determination of trace elements of Egyptian cane sugar (Naga Hammady factories) by neutron activation, atomic absorption spectrophotometric and inductively coupled plasma-atomic emission spectrometric analyses.

    PubMed

    Awadallah, R M; Sherif, M K; Mohamed, A E; Grass, F

    1984-01-01

    INAA, AAS and ICP-AES techniques are applied to the determination of trace amounts of Ag, Al, As, Au, Ba, Br, Ca, Cd, Ce, Cl, Co, Cr, Cs, Cu, Dy, Eu, Fe, Ga, Hf, K, La, Li, Lu, Mg, Mn, Na, Nb, Ni, Pb, Sb, Sc, Se, Sm, Sn, Sr, Ta, Th, Ti, U, V, W and Zn in the stalks of sugar cane plant after extracting juice, raw juice principal (mixed) juice, juice withdrawn from the successive stages of sugar industry, sirup, deposits from evaporators, molasse, A-? and B-sugar and in the soil samples (collected from the field supplying the factories by cane plants) taken from the immediate vicinity of the plant roots at surface, 30 and 60 cm depth. The results obtained are in a good agreement of the safety baselines of using juice as beverage, molasse derivatives (honey, sweets, ...) as diet for common people in the developed countries and in industry (methanol, ethanol, acetone & acetic acid, ...) and sugar sweeting for many purposes (in beverages, desserts, ...). Differences of trace elements concentrations in soil samples may be reasoned to geochemical and biogeochemical fractionation while those in juice may be due to the changes in the environmental conditions, chemical composition and botanic structures. Variations in trace element contents in the products formed during the successive stages of sugar industry may be a result of evaporation, filtration processes, chemical treatments or corrosion of vessels, containers or engines. Trace elements are very important where they are responsible for enzymatic and biochemical reactions, matabolism, health and diseases.

  14. Fast Pyrolysis of Tropical Biomass Species and Influence of Water Pretreatment on Product Distributions.

    PubMed

    Morgan, Trevor James; Turn, Scott Q; Sun, Ning; George, Anthe

    2016-01-01

    The fast pyrolysis behaviour of pretreated banagrass was examined at four temperatures (between 400 and 600 C) and four residence times (between ~1.2 and 12 s). The pretreatment used water washing/leaching to reduce the inorganic content of the banagrass. Yields of bio-oil, permanent gases and char were determined at each reaction condition and compared to previously published results from untreated banagrass. Comparing the bio-oil yields from the untreated and pretreated banagrass shows that the yields were greater from the pretreated banagrass by 4 to 11 wt% (absolute) at all reaction conditions. The effect of pretreatment (i.e. reducing the amount of ash, and alkali and alkali earth metals) on pyrolysis products is: 1) to increase the dry bio-oil yield, 2) to decrease the amount of undetected material, 3) to produce a slight increase in CO yield or no change, 4) to slightly decrease CO2 yield or no change, and 5) to produce a more stable bio-oil (less aging). Char yield and total gas yield were unaffected by feedstock pretreatment. Four other tropical biomass species were also pyrolyzed under one condition (450°C and 1.4 s residence time) for comparison to the banagrass results. The samples include two hardwoods: leucaena and eucalyptus, and two grasses: sugarcane bagasse and energy-cane. A sample of pretreated energy-cane was also pyrolyzed. Of the materials tested, the best feedstocks for fast pyrolysis were sugarcane bagasse, pretreated energy cane and eucalyptus based on the yields of 'dry bio-oil', CO and CO2. On the same basis, the least productive feedstocks are untreated banagrass followed by pretreated banagrass and leucaena.

  15. Comparison of Two Methods for Estimating Adjustable One-Point Cane Length in Community-Dwelling Older Adults.

    PubMed

    Camara, Camila Thais Pinto; de Freitas, Sandra Maria Sbeghen Ferreira; de Lima, Waléria Paixão; Lima, Camila Astolphi; Amorim, César Ferreira; Perracini, Monica Rodrigues

    2017-01-01

    Our aim is to estimate inter-observer reliability, test-retest reliability, anthropometric and biomechanical adequacy and minimal detectable change when measuring the length of single-point adjustable canes in community-dwelling older adults. There are 112 participants in the study. They are men and women, aged 60 years and over, who were attending an outpatient community health centre. An exploratory study design was used. Participants underwent two assessments within the same day by two independent observers and by the same observer at an interval of 15-45 days. Two measures were used to establish the length of a single-point adjustable cane: the distance from the distal wrist crease to the floor (WF) and the distance from the top of the greater trochanter of the femur to the floor (TF). Each individual was fitted according to these two measures, and elbow flexion angle was measured. Inter-observer reliability and the test-retest reliability were high in both TF (ICC 3.1  = 0.918 and ICC 2.1  = 0.935) and WF measures (ICC 3.1  = 0.967 and ICC 2.1  = 0.960). Only 1% of the individuals kept an elbow flexion angle within the standard recommendation of 30° ± 10° when the cane length was determined by the TF measure, and 30% of the participants when the cane was determined by the WF measure. The minimal detectable cane length change was 2.2 cm. Our results suggest that, even though both measures are reliable, cane length determined by WF distance is more appropriate to keep the elbow flexion angle within the standard recommendation. The minimal detectable change corresponds to approximately a hole in the cane adjustment. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

  16. Biological nitrogen fixation in sugar cane: A key to energetically viable biofuel production

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Boddey, R.M.

    1995-05-01

    The advantages of producing biofuels to replace fossil energy sources are derived from the fact that the energy accumulated in the biomass in captured directly from photosynthesis and is thus renewable, and that the cycle of carbon dioxide fixation by the crop, followed by burning of the fuel makes no overall contribution to atmospheric CO{sub 2} or, consequently, to global warming. However, these advantages are negated if large quantities of fossil fuels need to be used to grow or process the biofuel crop. In this regard, the Brazilian bioethanol program, based on the fermentation/distillation of sugar cane juice, is particularlymore » favorable, not only because the crop is principally hand harvested, but also because of the low nitrogen fertilizer use on sugar cane in Brazil. Recent {sup 15}N and N balance studies have shown that in some Brazilian cane varieties, high yields are possible without N fertilization because the plants are able to obtain large contributions of nitrogen from plant-associated biological N{sub 2} fixation (BNF). The N{sub 2}-fixing acid-tolerant bacterium Acetobacter diazotrophicus was first found to occur within roots, stems, and leaves of sugar cane. Subsequently, two species of Herbaspirillum also have been found to occur within the interior of all sugar cane tissues. The discovery of these, and other N{sub 2}-fixing bacteria that survive poorly in soil but thrive within plant tissue (endophytic bacteria), may account for the high BNF contributions observed in sugar cane. Further study of this system should allow the gradual elimination of N fertilizer use on sugar cane, at least in Brazil, and opens up the possibility of the extension of this efficient N{sub 2}-fixing system to cereal and other crops with consequent immense potential benefits to tropical agriculture. 44 refs., 9 figs., 4 tabs.« less

  17. Invitro Digestion and Fermentation Characteristics of Temulose Molasses, a Co-Product of Fiberboard Production, and Select Temulose Fractions

    USDA-ARS?s Scientific Manuscript database

    It is of interest to discover new fermentable carbohydrates sources that function as prebiotics. This study evaluated the hydrolytic digestibility, fermentative capacity, and microbiota modulating properties of temulose molasses, four hydrolyzed fractions of temulose molasses, short-chain fructooli...

  18. 40 CFR 429.11 - General definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... of fiberboard products” means the air dry weight of hardboard or insulation board following formation... manufactured from interfelted ligno-cellulosic fibers consolidated under heat and pressure to a density of 0.5 g/cu cm (31 lb/cu ft) or greater. (f) The term “insulation board” means a panel manufactured from...

  19. 40 CFR 429.11 - General definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... of fiberboard products” means the air dry weight of hardboard or insulation board following formation... manufactured from interfelted ligno-cellulosic fibers consolidated under heat and pressure to a density of 0.5 g/cu cm (31 lb/cu ft) or greater. (f) The term “insulation board” means a panel manufactured from...

  20. 40 CFR 429.11 - General definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... of fiberboard products” means the air dry weight of hardboard or insulation board following formation... manufactured from interfelted ligno-cellulosic fibers consolidated under heat and pressure to a density of 0.5 g/cu cm (31 lb/cu ft) or greater. (f) The term “insulation board” means a panel manufactured from...

  1. 49 CFR 178.815 - Stacking test.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... deformation, which renders the IBC unsafe for transportation, and no loss of contents. (2) For fiberboard and wooden IBCs, there may be no loss of contents and no permanent deformation, which renders the whole IBC..., which renders the IBC unsafe for transportation, and no loss of contents. (4) For the dynamic...

  2. 49 CFR 178.815 - Stacking test.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... deformation, which renders the IBC unsafe for transportation, and no loss of contents. (2) For fiberboard and wooden IBCs, there may be no loss of contents and no permanent deformation, which renders the whole IBC..., which renders the IBC unsafe for transportation, and no loss of contents. (4) For the dynamic...

  3. 49 CFR 178.815 - Stacking test.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... deformation, which renders the IBC unsafe for transportation, and no loss of contents. (2) For fiberboard and wooden IBCs, there may be no loss of contents and no permanent deformation, which renders the whole IBC..., which renders the IBC unsafe for transportation, and no loss of contents. (4) For the dynamic...

  4. 49 CFR 178.815 - Stacking test.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... for transportation, and no loss of contents. (2) For fiberboard and wooden IBCs, there may be no loss... unsafe for transportation, and no loss of contents. (4) For the dynamic compression test, a container passes the test if, after application of the required load, there is no permanent deformation to the IBC...

  5. 49 CFR 178.815 - Stacking test.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... deformation, which renders the IBC unsafe for transportation, and no loss of contents. (2) For fiberboard and wooden IBCs, there may be no loss of contents and no permanent deformation, which renders the whole IBC..., which renders the IBC unsafe for transportation, and no loss of contents. (4) For the dynamic...

  6. Construction of Experimental Polyvinyl Chloride (PVC) Roofing.

    DTIC Science & Technology

    1984-04-01

    in. War II vintage; squash and handball courts were (13-mm) fiberboard, to comply with Sarnafil re- added in 1966. The entire structure is of wood con...squash and handball courts had a gravel surface. pendently, avoiding difficulties of trying to handle Figure 23 shows the building arrangements. two

  7. 75 FR 39871 - Manufactured Home Construction and Safety Standards

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-13

    ...) submitted by the MHCC. The MHCC has prepared and submitted to HUD its second group of recommendations to... modify the existing requirements for control of formaldehyde emissions in Sec. 3280.308, by lowering the... emission controls for medium density fiberboard materials (MDF) of 0.3 ppm. These changes recommended by...

  8. Constructed microhabitat bundles for sampling fishes and crayfishes in coastal plain streams

    Treesearch

    Melvin L. Warren; A.L. Sheldon; W.R. Haag

    2009-01-01

    We investigated fish and crayfish use of standardized, constructed microhabitats (bundles) in three northern Mississippi streams. Cypress Creek and the Little Tallahatchie Canal were channelized and incised and had little woody cover; Puskus Creek was unchannelized and unincised and had abundant woody cover. We constructed three types of bundles (cane, leaf, and string...

  9. Burial and thermal history of the Paradox Basin, Utah and Colorado, and petroleum potential of the Middle Pennsylvanian Paradox Basin

    USGS Publications Warehouse

    Nuccio, Vito F.; Condon, Steven M.

    1996-01-01

    The Ismay?Desert Creek interval and Cane Creek cycle of the Alkali Gulch interval of the Middle Pennsylvanian Paradox Formation in the Paradox Basin of Utah and Colorado contain excellent organic-rich source rocks having total organic carbon contents ranging from 0.5 to 11.0 percent. The source rocks in both intervals contain types I, II, and III organic matter and are potential source rocks for both oil and gas. Organic matter in the Ismay?Desert Creek interval and Cane Creek cycle of the Alkali Gulch interval (hereinafter referred to in this report as the ?Cane Creek cycle?) probably is more terrestrial in origin in the eastern part of the basin and is interpreted to have contributed to some of the gas produced there. Thermal maturity increases from southwest to northeast for both the Ismay?Desert Creek interval and Cane Creek cycle, following structural and burial trends throughout the basin. In the northernmost part of the basin, the combination of a relatively thick Tertiary sedimentary sequence and high basinal heat flow has produced very high thermal maturities. Although general thermal maturity trends are similar for both the Ismay?Desert Creek interval and Cane Creek cycle, actual maturity levels are higher for the Cane Creek due to the additional thickness (as much as several thousand feet) of Middle Pennsylvanian section. Throughout most of the basin, the Ismay?Desert Creek interval is mature and in the petroleum-generation window (0.10 to 0.50 production index (PI)), and both oil and gas are produced; in the south-central to southwestern part of the basin, however, the interval is marginally mature (0.10 PI) in the central part of the basin and is overmature (past the petroleum-generation window (>0.50 PI)) throughout most of the eastern part of the basin. The Cane Creek cycle generally produces oil and associated gas throughout the western and central parts of the basin and thermogenic gas in the eastern part of the basin. Burial and thermal-history models were constructed for six different areas of the Paradox Basin. In the Monument upwarp area, the least mature part of the basin, the Ismay?Desert Creek interval and Cane Creek cycle have thermal maturities of 0.10 and 0.20 PI and were buried to 13,400 ft and 14,300 ft, respectively. A constant heat flow through time of 40 mWm?2 (milliwatts per square meter) is postulated for this area. Significant petroleum generation began at 45 Ma for the Ismay?Desert Creek interval and at 69 Ma for the Cane Creek cycle. In the area around the confluence of the Green and Colorado Rivers, the Ismay?Desert Creek interval and Cane Creek cycle have thermal maturities of 0.20 and 0.25 PI and were buried to 13,000 ft and 14,200 ft, respectively. A constant heat flow through time of 42 mWm?2 is postulated for this area. Significant petroleum generation began at 60 Ma for the Ismay?Desert Creek interval and at 75 Ma for the Cane Creek cycle. In the area around the town of Green River, Utah, the Ismay?Desert Creek interval and Cane Creek cycle have thermal maturities of 0.60 and greater and were buried to 14,000 ft and 15,400 ft, respectively. A constant heat flow through time of 53 mWm?2 is proposed for this area. Significant petroleum generation began at 82 Ma for the Ismay?Desert Creek interval and at 85 Ma for the Cane Creek cycle. Around Moab, Utah, in the deeper, eastern part of the basin, the Ismay?Desert Creek interval and Cane Creek cycle have thermal maturities of 0.30 and around 0.35 PI and were buried to 18,250 ft and 22,000 ft, respectively. A constant heat flow through time of 40 mWm?2 is postulated for this area. Significant petroleum generation began at 79 Ma for the Ismay?Desert Creek interval and at 90 Ma for the Cane Creek cycle. At Lisbon Valley, also in the structurally deeper part of the basin, the Ismay?

  10. Energy cane as a multiple-products alternative

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Alexander, A.G.

    1984-01-01

    CANE SUGAR planting as it was formerly known is in serious and essentially irreversible trouble. Diversification of sugarcane to alternative farm crops is indicated in some instances. Yet, for the most part, the more logical alternative is an internal diversification to a multiple-products biomass commodity. Sometimes termed the energy cane approach, its keystones are the management of sugarcane as a quantitative rather than qualitative entity, and the inclusion of certain tropical-grass relatives to assist cane in its year-round supply of biomass to industrial consumers. Managed in this way, absolute tonnages of whole cane are increased materially beyond what is possiblemore » from sugar-crop management. Juice quality declines but sugar yields are significant as a function of high biomass tonnages per acre. Usage of the lignocellulose can range from low-quality humid boiler fuel in furnaces designed for refuse incineration, to higher-quality fuels in more efficient boilers, to proprietary fuels and chemical products, and to lignocellulose supply as the feedstock for primary chemicals production. The latter might include, for example, synthesis gas and petrochemicals in tropical regions lacking natural gas, naphtha, or coal as starting materials. Diversification of sugarcane to completely new farm commodities is opposed in favor of internal diversification to a high-growth, multiple-products commodity. Decisive issues here are as much educational as they are technical. The energy cane concept maintains that sugarcane is a future resource of enormous national and international value. It should develop accordingly where decision-taking is by persons who respect the cane plant and who have done their homework on its alternative-use potentials. 35 references, 5 figures, 6 tables.« less

  11. Assistive devices for balance and mobility: benefits, demands, and adverse consequences.

    PubMed

    Bateni, Hamid; Maki, Brian E

    2005-01-01

    To provide information on the advantages and possible disadvantages of using canes and walkers. English-language articles were identified by searching MEDLINE and PubMed (1966-May 2003) for key words cane or walker , excluding articles unrelated to mobility aids. Bibliographies were reviewed and ISI Web of Science citation searches were run to identify additional references. Over 1000 articles were selected for further evaluation. We extracted all studies of single-tip canes or pickup walkers addressing: (1) functional, biomechanic, or neuromotor benefits; (2) biomechanic, attentional, neuromotor, metabolic, or physiologic demands; and (3) falls, injuries, or other problems. We included approximately 10% of the articles originally identified. The methodology of each selected article, and findings relevant to the benefits, demands, or adverse effects of cane or walker use were summarized. Findings were synthesized by considering their relation to basic biomechanic principles. Some biomechanic findings appear to support the clinical view that canes and walkers can improve balance and mobility for older adults and people with other clinical conditions. However, a large proportion of users experience difficulties, and the use of such devices is associated with increased risk of falling. A small number of studies have characterized some of the specific demands and problems associated with using mobility aids. Clinical and biomechanic evaluations of canes and walkers confirm that these devices can improve balance and mobility. However, they can also interfere with ones ability to maintain balance in certain situations, and the strength and metabolic demands can be excessive. More research is needed to identify and solve specific problems. Such research may lead to improved designs and guidelines for safer use of canes and walkers.

  12. Exposure to elevated carbon dioxide concentration in the dark lowers the respiration quotient of Vitis cane wood.

    PubMed

    Smart, David R

    2004-01-01

    Cane cuttings of the grapevine rootstock Vitis rupestris Scheele x V. riparia Michx. cv. 3309 Couderc were brought out of endodormancy by warming at 30 degrees C. Cane pieces (12 to 13 cm long) with nodes containing a primary bud were placed in a gas exchange system and monitored for net respiratory fluxes of CO2 and O2. Grapevine respiration rates expressed on a wood volume basis were 1.4 to 3.4 mmol CO2 or O2 m-3s-1, which is higher than stem respiration rates reported for many other woody taxa but similar to rates measured for ecodormant buds of other Vitis species. Passive water loss from canes was 0.7 to 1.2 mmol H2O m-3s-1. During a 7-day period, nonstructural carbohydrate concentrations in cane wood declined only slightly, whereas sucrose was nearly completely consumed. When ambient CO2 concentration ([CO2]) was raised from 300 to 750 micro molmol-1 and then 2000 micromol mol-1, net CO2 exchange rates declined by 5.9 +/- 0.6 and then 11.0 +/- 0.6%, whereas net O2 consumption rates remained about constant. The mean respiration quotient (net CO2/O2 flux) for canes with intact ecodormant buds was 0.99 +/- 0.03 when the [CO2] was 300 micromol mol-1, and decreased to 0.87 +/- 0.03 and 0.088 +/- 0.02 when the [CO2] was increased to 750 and 2000 micromol mol-1, respectively. The results support the hypothesis that, in Vitis canes, inhibition of respiratory CO2 efflux in response to high [CO2] is an indirect consequence of non-photosynthetic carboxylation reactions, and not a result of inhibition of respiratory metabolism.

  13. Latin America Report

    DTIC Science & Technology

    1985-04-16

    that the cane grows and for pesticides to combat insects. In addition, to calculate the price per ton, it is necessary to take into ac- count the...Production (Cane) 1983-84 Expenditure Cost per ton of cane Materials 53.66 Manure and fertilizer 7.31 Pesticides 10.09 Fuel and lubricants 40.55...then Minister of External Affairs Basil Ince visited Venezuela in March 1984, the deal, was said to be "the major item on the agenda." CSO: 3298

  14. Electronic white cane with GPS radar-based concept as blind mobility enhancement without distance limitation

    NASA Astrophysics Data System (ADS)

    Halim, Suharsono; Handafiah, Finna; Aprilliyani, Ria; Udhiarto, Arief

    2018-02-01

    The Indonesian Ministry of Social Affairs, in July 2012, informed that the number of blind in Indonesia has been the largest among to the people with other disabilities. The most common tools utilized to help the blind was a conventional cane which has limited features and therefore it was difficult to be used as a mobilization tools. Moreover, the conventional cane cannot assist them or their family when the blind gets lost. In this research, we designed and implemented an electronic white cane with the concept of radar and global positioning system (GPS). The purpose of this research was to design and develop an electronic white cane which can enhance the mobility of the blind without distance coverage limitation. Utilizing ultrasonic sensors as a distance measurement and a servo motor as an actuator, the produced radar system is able to map an area with maximum distance and coverage angle of 5 meters and 180° respectively. The blind senses the obstacle around them from the vibration generated by five vibration motors. The vibration becomes more intense when the obstacle is detected closer. In addition, we implemented a GPS to monitor the blind's position and allow their family to find them easily when the blind need a help. Based on the tests performed, we have successfully developed an electronic white cane that can be a solution to improve the blind's mobility.

  15. Adaptability and Stability Study of Selected Sweet Sorghum Genotypes for Ethanol Production under Different Environments Using AMMI Analysis and GGE Biplots

    PubMed Central

    Cheruiyot, Erick Kimutai; Othira, Jacktone Odongo; Njuguna, Virginia Wanjiku; Macharia, Joseph Kinyoro; Owuoche, James; Oyier, Moses; Kange, Alex Machio

    2016-01-01

    The genotype and environment interaction influences the selection criteria of sorghum (Sorghum bicolor) genotypes. Eight sweet sorghum genotypes were evaluated at five different locations in two growing seasons of 2014. The aim was to determine the interaction between genotype and environment on cane, juice, and ethanol yield and to identify best genotypes for bioethanol production in Kenya. The experiments were conducted in a randomized complete block design replicated three times. Sorghum canes were harvested at hard dough stage of grain development and passed through rollers to obtain juice that was then fermented to obtain ethanol. Cane, juice, and ethanol yield was analyzed using the additive main effect and multiplication interaction model (AMMI) and genotype plus genotype by environment (GGE) biplot. The combined analysis of variance of cane and juice yield of sorghum genotypes showed that sweet sorghum genotypes were significantly (P < 0.05) affected by environments (E), genotypes (G) and genotype by environment interaction (GEI). GGE biplot showed high yielding genotypes EUSS10, ACFC003/12, SS14, and EUSS11 for cane yield; EUSS10, EUSS11, and SS14 for juice yield; and EUSS10, SS04, SS14, and ACFC003/12 for ethanol yield. Genotype SS14 showed high general adaptability for cane, juice, and ethanol yield. PMID:27777968

  16. Adaptability and Stability Study of Selected Sweet Sorghum Genotypes for Ethanol Production under Different Environments Using AMMI Analysis and GGE Biplots.

    PubMed

    Rono, Justice Kipkorir; Cheruiyot, Erick Kimutai; Othira, Jacktone Odongo; Njuguna, Virginia Wanjiku; Macharia, Joseph Kinyoro; Owuoche, James; Oyier, Moses; Kange, Alex Machio

    2016-01-01

    The genotype and environment interaction influences the selection criteria of sorghum ( Sorghum bicolor ) genotypes. Eight sweet sorghum genotypes were evaluated at five different locations in two growing seasons of 2014. The aim was to determine the interaction between genotype and environment on cane, juice, and ethanol yield and to identify best genotypes for bioethanol production in Kenya. The experiments were conducted in a randomized complete block design replicated three times. Sorghum canes were harvested at hard dough stage of grain development and passed through rollers to obtain juice that was then fermented to obtain ethanol. Cane, juice, and ethanol yield was analyzed using the additive main effect and multiplication interaction model (AMMI) and genotype plus genotype by environment (GGE) biplot. The combined analysis of variance of cane and juice yield of sorghum genotypes showed that sweet sorghum genotypes were significantly ( P < 0.05) affected by environments (E), genotypes (G) and genotype by environment interaction (GEI). GGE biplot showed high yielding genotypes EUSS10, ACFC003/12, SS14, and EUSS11 for cane yield; EUSS10, EUSS11, and SS14 for juice yield; and EUSS10, SS04, SS14, and ACFC003/12 for ethanol yield. Genotype SS14 showed high general adaptability for cane, juice, and ethanol yield.

  17. Linacre and Locke: Pillars of Medical Humanism

    PubMed Central

    Watson, Cecil J.

    1967-01-01

    The following address was given by Dr. Cecil J. Watson at the Wm. J. Kerr Gold Headed Cane Lecture, University of California School of Medicine, on 9 June 1967. At this event on the eve of Commencement Day, the senior student who has been chosen by his classmates and by his professors in the Department of Medicine as the one who best exemplifies the qualities of a true physician is awarded a gold-headed cane.* This carries on the British tradition of a similar cane that was passed from physician to physician from 1689 to 1825. The original cane, which was carried successively by Doctors John Radcliffe, Richard Mead, Anthony Askew, David Pitcairn and Matthew Baillie, now rests in the Hall of the Royal College of Physicians in London. PMID:4867206

  18. Plant development and yield of four sugarcane varieties irrigated by a subsurface drip irrigation system in Campinas, Brazil

    NASA Astrophysics Data System (ADS)

    Silva, André Luiz Barros de O.; Célia de Matos Pires, Regina; Yukitaka Pessinati Ohashi, Augusto; Vasconcelos Ribeiro, Rafael; Landell, Marcos Guimarães de Andrade; Aparecida Creste Dias de Souza, Silvana

    2013-04-01

    The biofuel production is a growing concern on modern society due to the agricultural sustainability, in which both food and energy supply should be taken into account. The agroclimatic zoning indicates that sugarcane expansion in Brazil can only take place in marginal lands, where water deficit occurs and irrigation is necessary. The use of subsurface drip irrigation (SDI) in sugarcane cultivation is an interesting cultural practice to improve production and allow cultivation in marginal lands due to water deficit conditions or to attain high yield and to increase longevity of plants. In this context it is necessary to investigate responses of different varieties to water supply. The aim of this work was to evaluate the plant development and yield of four sugarcane varieties irrigated by a subsurface drip irrigation system in Campinas, Brazil in the 1st cane ratoon cycle. The field experiment was carried out in Campinas SP Brazil, with IACSP95-5000, IACSP94-2094, IACSP94-2101 and SP79-1011 cultivars in the 1st cane ratoon cycle, from January (after the harvest of cane plant cycle) to October (harvest the 1st cane ratoon cycle). The plant spacing was 1.5 m between rows. Each cultivar was planted in an area of 0.4 hectares. The irrigation was done by a subsuperficial drip system with one drip line in each plant row installed at 0.25 m deep. During the 1st cane ratoon cycle the parameters were analysed on the 33rd, 123rd, 185th and 277th day. The analysed parameters were: plant yield (m), leaf area index (LAI) and yield (tons per hectare). According to the results from the second sampling (123rd day) the varieties IACSP95-5000 and IACSP94-2101 showed higher plant height when compared to the other varieties. However, from the third sampling (185th day) on the IACSP95-5000 variety grew considerably taller than the other varieties. The varieties SP79-1011and IACSP94-2101 presented lower values of LAI throughout the crop cycle when compared to other varieties. But on the third evaluation (185th day) DAP the LAI obtained in IACSP94-2101 variety reached a value close to that observed in IACSP94-2094. On the first two evaluations at 33rd and 123rd days the values achieved by varieties IACSP95-5000 and IACSP94-2094 were similar. On the last assessment the highest value of LAI was observed in IACSP95-5000 variety, reaching 6.47 LAI. From the second evaluation the highest value of yield were observed in IACSP95-5000 variety. On the last evaluation variety IACSP95-5000 yield reached over 140 tons per hectare. This productivity was 37%, 51% and 64% higher than the values obtained in the varieties SP79-1011, IACSP94-2101 and IACSP94-2094, respectively. This variety reached the greatest plant growth (height and LAI) and the highest yield in the first ratoon cane cycle under subsurface drip irrigation system. Based on the obtained results this variety has shown promise for cultivation under subsurface drip irrigation system.

  19. 40 CFR 409.21 - Specialized definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  20. 40 CFR 409.21 - Specialized definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  1. 40 CFR 409.21 - Specialized definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  2. 40 CFR 409.21 - Specialized definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  3. Heat Transmission Properties of Insulating and Building Materials

    National Institute of Standards and Technology Data Gateway

    SRD 81 NIST Heat Transmission Properties of Insulating and Building Materials (Web, free access)   NIST has accumulated a valuable and comprehensive collection of thermal conductivity data. Version 1.0 of the database includes data for over 2000 measurements, covering several categories of materials including concrete, fiberboard, plastics, thermal insulation, and rubber.

  4. 49 CFR 178.930 - Standards for fiberboard Large Packagings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... in handling and transport. Where a detachable pallet is used, its top surface must be free from protrusions that might damage the Large Packaging. (3) Strengthening devices, such as timber supports to...

  5. 49 CFR 178.930 - Standards for fiberboard Large Packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... in handling and transport. Where a detachable pallet is used, its top surface must be free from protrusions that might damage the Large Packaging. (3) Strengthening devices, such as timber supports to...

  6. 49 CFR 178.930 - Standards for fiberboard Large Packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... in handling and transport. Where a detachable pallet is used, its top surface must be free from protrusions that might damage the Large Packaging. (3) Strengthening devices, such as timber supports to...

  7. 49 CFR 178.930 - Standards for fiberboard Large Packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... in handling and transport. Where a detachable pallet is used, its top surface must be free from protrusions that might damage the Large Packaging. (3) Strengthening devices, such as timber supports to...

  8. 49 CFR 178.930 - Standards for fiberboard Large Packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... puncture resistance of 15 Joules (11 foot-pounds of energy) measured according to ISO 3036 (IBR, see § 171... in handling and transport. Where a detachable pallet is used, its top surface must be free from protrusions that might damage the Large Packaging. (3) Strengthening devices, such as timber supports to...

  9. Effects of pressing schedule on formation of vertical density profile for MDF panels

    Treesearch

    Zhiyong Cai; James H. Muehl; Jerrold E. Winandy

    2006-01-01

    A fundamental understanding of mat consolidation during hot pressing will help to optimize the medium-density fiberboard (MDF) manufacturing process by increasing productivity, improving product quality, and enhancing durability. Effects of panel density, fiber moisture content (MC), and pressing schedule on formation of vertical density profile (VDP) during hot...

  10. 49 CFR 173.334 - Organic phosphates mixed with compressed gas.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) Cylinders may be packed in strong wooden boxes with valves or other closing devices protected from damage, with not more than twelve cylinders in one outside wooden box. An outer fiberboard box may be used when... must be overpacked in a box, crate, or other strong outer packaging conforming to the requirements of...

  11. 49 CFR 173.334 - Organic phosphates mixed with compressed gas.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...) Cylinders may be packed in strong wooden boxes with valves or other closing devices protected from damage, with not more than twelve cylinders in one outside wooden box. An outer fiberboard box may be used when... must be overpacked in a box, crate, or other strong outer packaging conforming to the requirements of...

  12. 49 CFR 173.156 - Exceptions for limited quantity and ORM.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., carts, boxes or similar overpacks; (ii) Offered for transportation or transported by: (A) Rail; (B... transported to a disposal facility from one offeror. (2) The 30 kg (66 pounds) gross weight limitation does... a fiberboard box which is banded and secured to a wooden pallet by metal, fabric, or plastic straps...

  13. 49 CFR 173.334 - Organic phosphates mixed with compressed gas.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...) Cylinders may be packed in strong wooden boxes with valves or other closing devices protected from damage, with not more than twelve cylinders in one outside wooden box. An outer fiberboard box may be used when... must be overpacked in a box, crate, or other strong outer packaging conforming to the requirements of...

  14. 49 CFR 173.334 - Organic phosphates mixed with compressed gas.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...) Cylinders may be packed in strong wooden boxes with valves or other closing devices protected from damage, with not more than twelve cylinders in one outside wooden box. An outer fiberboard box may be used when... must be overpacked in a box, crate, or other strong outer packaging conforming to the requirements of...

  15. Fiberboards from loblolly pine refiner groundwood: aspects of fiber morphology

    Treesearch

    Charles W. McMillin

    1969-01-01

    In tests with Pinus taeda L., most properties of wet formed hardboard were improved by using fiber refined from wood having short, slender tracheids with thin walls. A theoretical analysis suggested that the fibers fail in bending while under stress induced by the pressing operation. Sush bending failures improve conditions from hydrogen bonding,...

  16. Properties of medium-density fiberboard related to hardwood specific gravity

    Treesearch

    George E. Woodson

    1976-01-01

    Boards of acceptable quality were made from barky material, pressure-refined from 14 species of southern hardwoods. Static bending and tensile properties (parallel to surface) of specimens were negatively correlated to stem specific gravity (wood plus bark), chip bulk density, and fiber bulk density. Bending and tensile properties increased with increasing...

  17. 40 CFR 63.2292 - What definitions apply to this subpart?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., board coolers, and other process units associated with the manufacturing of plywood and composite wood... are not part of the dryer heated zones. Dry forming means the process of making a mat of resinated..., medium density fiberboard, or hardboard. Dry rotary dryer means a rotary dryer that dries wood particles...

  18. 40 CFR 63.2292 - What definitions apply to this subpart?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., board coolers, and other process units associated with the manufacturing of plywood and composite wood... are not part of the dryer heated zones. Dry forming means the process of making a mat of resinated..., medium density fiberboard, or hardboard. Dry rotary dryer means a rotary dryer that dries wood particles...

  19. More rapid edgewise crush test methods

    Treesearch

    Thomas J. Urbanik; Arthur H. Catlin; Davide R. Friedman; Richard C. Lund

    1993-01-01

    The use of paraffin wax to reinforce the loading edges of corrugated fiberboard edge-crush specimens requires that the specimens be reconditioned after waxing. The traditional practice employing a 24-h reconditioning period is a conservative approach based on the moisture response rate of corrugated containers. An interlaboratory study was conducted to determine the...

  20. Moisture sorption properties of composite boards from esterified aspen fiber

    Treesearch

    C. Clemons; R. A. Young; R. M. Rowell

    1992-01-01

    One barrier to producing wood-plastic composites with wood fiber is the poor thermoplasticity of wood fiber. The objective of our study was to determine the plasticization of chemically modified wood fiber through tests on unmodified and esterified fiberboards. Attrition-milled aspen fiber was esterified with neat acetic, maleic, or succinic anhydride. Fourier...

  1. Relationship between Fiber Furnish and the Structural Performance of MDF

    Treesearch

    Leslie H. Groom; Laurence Mott; Stephen Shaler

    1999-01-01

    The structural performance of medium density fiberboard (MDF) is attributable to three primary variables which are: physical and mechanical properties of individual wood fibers; fiber-to-fiber stress transfer; and fiber orientation. These origins of fiber properties and stress transfer can be traced to the fiber generation method wherein fiber orientation is associated...

  2. Principles of minimum cost refining for optimum linerboard strength

    Treesearch

    Thomas J. Urbanik; Jong Myoung Won

    2006-01-01

    The mechanical properties of paper at a single basis weight and a single targeted refining freeness level have traditionally been used to compare papers. Understanding the economics of corrugated fiberboard requires a more global characterization of the variation of mechanical properties and refining energy consumption with freeness. The cost of refining energy to...

  3. 3D engineered fiberboard : a new structural building product

    Treesearch

    John F. Hunt; Jerrold E. Winandy

    2002-01-01

    To help meet the need for sustainable forest management tools, the USDA Forest Products Laboratory is developing an economically viable process to produce three-dimensional structural fibreboard products that can utilize a wide range of lignocellulosic fibres contained in the forest undergrowth and in underutilized timber. This will encourage the public and private...

  4. Cradle to Gate Life Cycle Assessment of North American Cellulosic Fiberboard Production

    Treesearch

    Maureen Puettmann; Richard Bergman; Elaine Oneil

    2016-01-01

    All consumer products have an environmental footprint. Quantifying that footprint has become more common with the advent of Environmental Preferential Purchasing (EPP), an emergent world-wide phenomenon. The forest products industry in particular has been challenged regarding its environmental sustainability. The greatest challenges with respect to practices center on...

  5. Finite element corroboration of buckling phenomena observed in corrugated boxes

    Treesearch

    Thomas J. Urbanik; Edmond P. Saliklis

    2003-01-01

    Conventional compression strength formulas for corrugated fiberboard boxes are limited to geometry and material that produce an elastic postbuckling failure. Inelastic postbuckling can occur in squatty boxes and trays, but a mechanistic rationale for unifying observed strength data is lacking. This study combines a finite element model with a parametric design of the...

  6. Fiberboard created using the natural adhesive properties of distillers dried grains with solubles

    USDA-ARS?s Scientific Manuscript database

    Distillers dried grains with solubles (DDGS) were employed as a bio-based resin/adhesive. DDGS were defatted with hexane, ball ground and screened prior to use. DDGS flour was mixed dry with Paulownia wood (PW) to make composites using the following conditions: temperature of 150-195 oC, PW particle...

  7. Capacity, production, and manufacturing of woodbased panels in North America

    Treesearch

    Henry Spelter

    1994-01-01

    This report is an informational report about four wood-based panel industries: particleboard, oriented strandboard, medium density fiberboard, and Southern Pine plywood. Items highlighted are trends in manufacturing and new plant costs, industry manufacturing capacity, and location. Recent data show the greatest amount of growth taking place in the oriented strandboard...

  8. Adhesives with wood materials : bond formation and performance

    Treesearch

    Charles R. Frihart; Christopher G. Hunt

    2010-01-01

    Adhesive bonding of wood plays an increasing role in the forest products industry and is a key factor for efficiently utilizing our timber resource. The main use of adhesives is in the manufacture of building materials, including plywood, oriented strandboard, particleboard, fiberboard, structural composite lumber, doors, windows and frames, and factory-laminated wood...

  9. Life-Cycle Inventory Analysis of Cellulosic Fiberboard Production in North America

    Treesearch

    Richard D. Bergman

    2014-01-01

    Documenting the environmental performance of building products is becoming widespread because of many green-marketing claims made without scientific merit (i.e., green-washing). Developing environmental product declarations (EPDs) for building products is one way to accomplish this objective for scientific documentation and to counter green-washing. EPDs are based on...

  10. Steam-assisted hot-pressing of construction plywood

    Treesearch

    Ronald W. Jokerst; Robert L. Geimer

    1994-01-01

    This study was designed to determine if steam injection pressing used for fiberboard, particleboard, and flakeboard could be adapted to the pressing of plywood. Plywood panels were fabricated with and without adhesive and then pressed to determine the effects of steam injection Lime, steam injection pressure, and press pressure on heat transfer rate, moisture...

  11. 78 FR 2416 - Notice of Issuance of Final Determination Concerning Rybix® (Tramadol Hydrochloride) Tablets

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-11

    ... for the management of moderate to moderately severe pain in adults. The active pharmaceutical... fiberboard drums. The fourth stage of French manufacturing is packaging in child- resistant blister packs...) in the case of an article which consists in whole or in part of materials from another country or...

  12. Selected properties of MDF and flakeboard overlaid with fiberglass mats

    Treesearch

    Zhiyong Cai

    2006-01-01

    Nonwoven fiberglass face laminates have long been applied to consolidated wood- based composites to improve their performance and serviceability. In this study, fiberglass mats with 50 percent resin binder were applied as face laminates to unconsolidated wood fiber or flake mats, then hot-pressed to make overlaid medium density fiberboard and flakeboard. Fiberglass...

  13. Composites from southern pine juvenile wood. Part 2. Durability and dimensional stability

    Treesearch

    Anton D. Pugel; Eddie W. Price; Chung-Yun Hse

    1990-01-01

    Southern pine juvenile and mature wood were processed into three composites: flakeboard, particleboard, and fiberboard. The durability of these composites was assessed by subjecting specimens to an ovendry-vacuumpressure-soak (ODVPS) treatment, and then evaluated for modulus of elasticity, modulus of rupture, and internal bond. Overall, juvenile wood composites had...

  14. Ozone reactions with indoor materials during building disinfection

    NASA Astrophysics Data System (ADS)

    Poppendieck, D.; Hubbard, H.; Ward, M.; Weschler, C.; Corsi, R. L.

    There is scant information related to heterogeneous indoor chemistry at ozone concentrations necessary for the effective disinfection of buildings, i.e., hundreds to thousands of ppm. In the present study, 24 materials were exposed for 16 h to ozone concentrations of 1000-1200 ppm in the inlet streams of test chambers. Initial ozone deposition velocities were similar to those reported in the published literature for much lower ozone concentrations, but decayed rapidly as reaction sites on material surfaces were consumed. For every material, deposition velocities converged to a relatively constant, and typically low, value after approximately 11 h. The four materials with the highest sustained deposition velocities were ceiling tile, office partition, medium density fiberboard and gypsum wallboard backing. Analysis of ozone reaction probabilities indicated that throughout each experiment, and particularly after several hours of disinfection, surface reaction resistance dominated the overall resistance to ozone deposition for nearly all materials. Total building disinfection by-products (all carbonyls) were quantified per unit area of each material for the experimental period. Paper, office partition, and medium density fiberboard each released greater than 38 mg m -2 of by-products.

  15. Spatial Dependence of Physical Attributes and Mechanical Properties of Ultisol in a Sugarcane Field.

    PubMed

    Tavares, Uilka Elisa; Rolim, Mário Monteiro; de Oliveira, Veronildo Souza; Pedrosa, Elvira Maria Regis; Siqueira, Glécio Machado; Magalhães, Adriana Guedes

    2015-01-01

    This study investigates the effect of conventional tillage and application of the monoculture of sugar cane on soil health. Variables like density, moisture, texture, consistency limits, and preconsolidation stress were taken as indicators of soil quality. The measurements were made at a 120 × 120 m field cropped with sugar cane under conventional tillage. The objective of this work was to characterize the soil and to study the spatial dependence of the physical and mechanical attributes. Then, undisturbed soil samples were collected to measure bulk density, moisture content and preconsolidation stress and disturbed soil samples for classification of soil texture, and consistency limits. The soil texture indicated that soil can be characterized as sandy clay soil and a sandy clay loam soil, and the consistency limits indicated that the soil presents an inorganic low plasticity clay. The preconsolidation tests tillage in soil moisture content around 19% should be avoided or should be chosen a management of soil with lighter vehicles in this moisture content, to avoid risk of compaction. Using geostatistical techniques mapping was possible to identify areas of greatest conservation soil and greater disturbance of the ground.

  16. Spatial Dependence of Physical Attributes and Mechanical Properties of Ultisol in a Sugarcane Field

    PubMed Central

    Tavares, Uilka Elisa; Monteiro Rolim, Mário; Souza de Oliveira, Veronildo; Maria Regis Pedrosa, Elvira; Siqueira, Glécio Machado; Guedes Magalhães, Adriana

    2015-01-01

    This study investigates the effect of conventional tillage and application of the monoculture of sugar cane on soil health. Variables like density, moisture, texture, consistency limits, and preconsolidation stress were taken as indicators of soil quality. The measurements were made at a 120 × 120 m field cropped with sugar cane under conventional tillage. The objective of this work was to characterize the soil and to study the spatial dependence of the physical and mechanical attributes. Then, undisturbed soil samples were collected to measure bulk density, moisture content and preconsolidation stress and disturbed soil samples for classification of soil texture, and consistency limits. The soil texture indicated that soil can be characterized as sandy clay soil and a sandy clay loam soil, and the consistency limits indicated that the soil presents an inorganic low plasticity clay. The preconsolidation tests tillage in soil moisture content around 19% should be avoided or should be chosen a management of soil with lighter vehicles in this moisture content, to avoid risk of compaction. Using geostatistical techniques mapping was possible to identify areas of greatest conservation soil and greater disturbance of the ground. PMID:26167528

  17. 40 CFR 409.31 - Specialized definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  18. The Effects of Fiber Inclusion on Pet Food Sensory Characteristics and Palatability

    PubMed Central

    Koppel, Kadri; Monti, Mariana; Gibson, Michael; Alavi, Sajid; Donfrancesco, Brizio Di; Carciofi, Aulus Cavalieri

    2015-01-01

    Simple Summary The results from this research indicate that fibers have an effect on extruded pet food texture and palatability. These results may help pet food companies select ingredients for successful product formulations. Abstract The objectives of this study were to determine (a) the influence of fiber on the sensory characteristics of dry dog foods; (b) differences of coated and uncoated kibbles for aroma and flavor characteristics; (c) palatability of these dry dog foods; and (d) potential associations between palatability and sensory attributes. A total of eight fiber treatments were manufactured: a control (no fiber addition), guava fiber (3%, 6%, and 12%), sugar cane fiber (9%; large and small particle size), and wheat bran fiber (32%; large and small particle size). The results indicated significant effects of fibers on both flavor and texture properties of the samples. Bitter taste and iron and stale aftertaste were examples of flavor attributes that differed with treatment, with highest intensity observed for 12% guava fiber and small particle size sugar cane fiber treatments. Fracturability and initial crispness attributes were lowest for the sugar cane fiber treatments. Flavor of all treatments changed after coating with a palatant, increasing in toasted, brothy, and grainy attributes. The coating also had a masking effect on aroma attributes such as stale, flavor attributes such as iron and bitter taste, and appearance attributes such as porosity. Palatability testing results indicated that the control treatment was preferred over the sugar cane or the wheat bran treatment. The treatment with large sugarcane fiber particles was preferred over the treatment with small particles, while both of the wheat bran treatments were eaten at a similar level. Descriptive sensory analysis data, especially textural attributes, were useful in pinpointing the underlying characteristics and were considered to be reasons that may influence palatability of dog foods manufactured with inclusion of different fibers. PMID:26479141

  19. Skilled nursing facilities after joint replacement

    MedlinePlus

    ... able to: Safely get around using a cane, walker, or crutches. Get in and out of a ... climb steps, keep your balance, and use a walker, cane, or crutches. Occupational therapists will teach you ...

  20. 40 CFR 409.21 - Specialized definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409... raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  1. Exploiting intraspecific competitive mechanisms to control invasive cane toads (Rhinella marina)

    PubMed Central

    Crossland, Michael R.; Haramura, Takashi; Salim, Angela A.; Capon, Robert J.; Shine, Richard

    2012-01-01

    If invasive species use chemical weapons to suppress the viability of conspecifics, we may be able to exploit those species-specific chemical cues for selective control of the invader. Cane toads (Rhinella marina) are spreading through tropical Australia, with negative effects on native species. The tadpoles of cane toads eliminate intraspecific competitors by locating and consuming newly laid eggs. Our laboratory trials show that tadpoles find those eggs by searching for the powerful bufadienolide toxins (especially, bufogenins) that toads use to deter predators. Using those toxins as bait, funnel-traps placed in natural waterbodies achieved near-complete eradication of cane toad tadpoles with minimal collateral damage (because most native (non-target) species are repelled by the toads' toxins). More generally, communication systems that have evolved for intraspecific conflict provide novel opportunities for invasive-species control. PMID:22696528

  2. The impact of invasive cane toads on native wildlife in southern Australia.

    PubMed

    Jolly, Christopher J; Shine, Richard; Greenlees, Matthew J

    2015-09-01

    Commonly, invaders have different impacts in different places. The spread of cane toads (Rhinella marina: Bufonidae) has been devastating for native fauna in tropical Australia, but the toads' impact remains unstudied in temperate-zone Australia. We surveyed habitat characteristics and fauna in campgrounds along the central eastern coast of Australia, in eight sites that have been colonized by cane toads and another eight that have not. The presence of cane toads was associated with lower faunal abundance and species richness, and a difference in species composition. Populations of three species of large lizards (land mullets Bellatorias major, eastern water dragons Intellagama lesueurii, and lace monitors Varanus varius) and a snake (red-bellied blacksnake Pseudechis porphyriacus) were lower (by 84 to 100%) in areas with toads. The scarcity of scavenging lace monitors in toad-invaded areas translated into a 52% decrease in rates of carrion removal (based on camera traps at bait stations) and an increase (by 61%) in numbers of brush turkeys (Alectura lathami). The invasion of cane toads through temperate-zone Australia appears to have reduced populations of at least four anurophagous predators, facilitated other taxa, and decreased rates of scavenging. Our data identify a paradox: The impacts of cane toads are at least as devastating in southern Australia as in the tropics, yet we know far more about toad invasion in the sparsely populated wilderness areas of tropical Australia than in the densely populated southeastern seaboard.

  3. Advanced Augmented White Cane with obstacle height and distance feedback.

    PubMed

    Pyun, Rosali; Kim, Yeongmi; Wespe, Pascal; Gassert, Roger; Schneller, Stefan

    2013-06-01

    The white cane is a widely used mobility aid that helps visually impaired people navigate the surroundings. While it reliably and intuitively extends the detection range of ground-level obstacles and drop-offs to about 1.2 m, it lacks the ability to detect trunk and head-level obstacles. Electronic Travel Aids (ETAs) have been proposed to overcome these limitations, but have found minimal adoption due to limitations such as low information content and low reliability thereof. Although existing ETAs extend the sensing range beyond that of the conventional white cane, most of them do not detect head-level obstacles and drop-offs, nor can they identify the vertical extent of obstacles. Furthermore, some ETAs work independent of the white cane, and thus reliable detection of surface textures and drop-offs is not provided. This paper introduces a novel ETA, the Advanced Augmented White Cane, which detects obstacles at four vertical levels and provides multi-sensory feedback. We evaluated the device in five blindfolded subjects through reaction time measurements following the detection of an obstacle, as well as through the reliability of dropoff detection. The results showed that our aid could help the user successfully detect an obstacle and identify its height, with an average reaction time of 410 msec. Drop-offs were reliably detected with an intraclass correlation > 0.95. This work is a first step towards a low-cost ETA to complement the functionality of the conventional white cane.

  4. Determination of phenolic compounds content and antioxidant activity in skin, pulp, seed, cane and leaf of five native grape cultivars in West Azerbaijan province, Iran.

    PubMed

    Farhadi, Khalil; Esmaeilzadeh, Forough; Hatami, Mehdi; Forough, Mehrdad; Molaie, Rahim

    2016-05-15

    In the present work, the phenolic compounds content and antioxidant activity in the skin, pulp, seed, cane and leaf of one international (Muscat) and five native (Hosseini, Ghara Shira, Agh Shani, Ghara Shani and Ghara Ghandome) grape cultivated in West Azerbaijan, Iran were investigated. Ghara Shani grape skin was found to contain the highest content of total phenolic and anthocyanin and cane of Ghara Shani contains the highest amount of flavonoid. A remarkable DPPH radical scavenging activity up to 95% and consequently, the lowest IC50 was found for skin of Ghara Shani. According to RP-HPLC experiments, the highest concentration of phenolic compounds was identified as catechin (945 μg/g), epicatechin (482 μg/g), gallic acid (319 μg/g) and resveratrol (29.8 μg/g) in skin of Ghara Shani, quercetin in cane of Ghara Shani (956 μg/g), rutin in skin of Ghara Shira (298 μg/g) and caffeic acid in cane of Ghara Shira (17.4 μg/g). Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. The Interacting Effects of Ungulate Hoofprints and Predatory Native Ants on Metamorph Cane Toads in Tropical Australia

    PubMed Central

    Cabrera-Guzmán, Elisa; Crossland, Michael R.; González-Bernal, Edna; Shine, Richard

    2013-01-01

    Many invasive species exploit the disturbed habitats created by human activities. Understanding the effects of habitat disturbance on invasion success, and how disturbance interacts with other factors (such as biotic resistance to the invaders from the native fauna) may suggest new ways to reduce invader viability. In tropical Australia, commercial livestock production can facilitate invasion by the cane toad (Rhinella marina), because hoofprints left by cattle and horses around waterbody margins provide distinctive (cool, moist) microhabitats; nevertheless the same microhabitat can inhibit the success of cane toads by increasing the risks of predation or drowning. Metamorph cane toads actively select hoofprints as retreat-sites to escape dangerous thermal and hydric conditions in the surrounding landscape. However, hoofprint geometry is important: in hoofprints with steep sides the young toads are more likely to be attacked by predatory ants (Iridomyrmex reburrus) and are more likely to drown following heavy rain. Thus, anthropogenic changes to the landscape interact with predation by native taxa to affect the ability of cane toads in this vulnerable life-history stage to thrive in the harsh abiotic conditions of tropical Australia. PMID:24255703

  6. Techno-economic analysis of biodiesel and ethanol co-production from lipid-producing sugarcane: Biodiesel and Ethanol Co-Production from Lipid-Producing Sugarcane

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Huang, Haibo; Long, Stephen; Singh, Vijay

    Biodiesel production from vegetable oils has progressively increased over the past two decades. However, due to the low amounts of oil produced per hectare from temperate oilseed crops (e.g. soybean), the opportunities for further increasing biodiesel production are limited. Genetically modified lipid-producing sugarcane (lipid-cane) possesses great potential for producing biodiesel as an alternative feedstock because of sugarcane’s much higher productivity compared with soybean. In this study, techno-economic models were developed for biodiesel and ethanol coproduction from lipid-cane, assuming 2, 5, 10, or 20% lipid concentration in the harvested stem (dry mass basis). The models were compared with a conventional soybeanmore » biodiesel process model to assess lipid-cane’s competiveness. In the lipid-cane process model, the extracted lipids were used to produce biodiesel by transesterifi cation, and the remaining sugar was used to produce ethanol by fermentation. The results showed that the biodiesel production cost from lipid-cane decreased from $0.89/L to $0.59 /L as the lipid content increased from 2 to 20%; this cost was lower than that obtained for soybeans ($1.08/L). The ethanol production costs from lipid-cane were between $0.40/L and $0.46/L. The internal rate of return (IRR) for the soybean biodiesel process was 15.0%, and the IRR for the lipid-cane process went from 13.7 to 24.0% as the lipid content increased from 2 to 20%. Because of its high productivity, lipid-cane with 20% lipid content can produce 6700 L of biodiesel from each hectare of land, whereas soybean can only produce approximately 500 L of biodiesel from each hectare of land. This would indicate that continued efforts to achieve lipid-producing sugarcane could make large-scale replacement of fossil-fuel-derived diesel without unrealistic demands on land area.« less

  7. Techno-economic analysis of biodiesel and ethanol co-production from lipid-producing sugarcane: Biodiesel and Ethanol Co-Production from Lipid-Producing Sugarcane

    DOE PAGES

    Huang, Haibo; Long, Stephen; Singh, Vijay

    2016-03-07

    Biodiesel production from vegetable oils has progressively increased over the past two decades. However, due to the low amounts of oil produced per hectare from temperate oilseed crops (e.g. soybean), the opportunities for further increasing biodiesel production are limited. Genetically modified lipid-producing sugarcane (lipid-cane) possesses great potential for producing biodiesel as an alternative feedstock because of sugarcane’s much higher productivity compared with soybean. In this study, techno-economic models were developed for biodiesel and ethanol coproduction from lipid-cane, assuming 2, 5, 10, or 20% lipid concentration in the harvested stem (dry mass basis). The models were compared with a conventional soybeanmore » biodiesel process model to assess lipid-cane’s competiveness. In the lipid-cane process model, the extracted lipids were used to produce biodiesel by transesterifi cation, and the remaining sugar was used to produce ethanol by fermentation. The results showed that the biodiesel production cost from lipid-cane decreased from $0.89/L to $0.59 /L as the lipid content increased from 2 to 20%; this cost was lower than that obtained for soybeans ($1.08/L). The ethanol production costs from lipid-cane were between $0.40/L and $0.46/L. The internal rate of return (IRR) for the soybean biodiesel process was 15.0%, and the IRR for the lipid-cane process went from 13.7 to 24.0% as the lipid content increased from 2 to 20%. Because of its high productivity, lipid-cane with 20% lipid content can produce 6700 L of biodiesel from each hectare of land, whereas soybean can only produce approximately 500 L of biodiesel from each hectare of land. This would indicate that continued efforts to achieve lipid-producing sugarcane could make large-scale replacement of fossil-fuel-derived diesel without unrealistic demands on land area.« less

  8. Physiological performance and work capacity of Sudanese cane cutters with Schistosoma mansoni infection.

    PubMed

    Collins, K J; Brotherhood, R J; Davies, C T; Doré, C; Hackett, A J; Imms, F J; Musgrove, J; Weiner, J S; Amin, M A; El Karim, M; Ismail, H M; Omer, A H; Sukkar, M Y

    1976-05-01

    Physiological tests of work performance and measurement of field productivity were made in 194 Sudanese cane cutters in order to study the effect of Schistosoma mansoni infection. The cane cutters were selected from two age ranges (16-24 and 25-45 years) and subdivided into three clinical groups: not infected, infected with, and infected without clinical signs of hepatosplenomegaly. Men infected with Schistosoma haemotobium, malaria (blood film), or with hemoglobin levels less than 10 g/100 ml were excluded. There was a statistically significant (P less than 0.002) higher mean hemoglobin concentration in those not infected but the mean difference was less than 1 g/100 ml. Submaximal responses to exercise on a stationary bicycle ergometer, oxygen intake, ventilation, tidal volume, cardiac frequency and estimated maximal aerobic power output calculated both in absolute terms and relative to lean body mass and leg volume were similar in the six groups of cane cutters. No significant differences were found in physique, body composition or in thermoregulatory function tests. The cane cutters were found to have little natural acclimatization to heat in terms of sweating capacity when compared with a group of fully acclimatized Sudanese soldiers. The mean productivity (mean daily weight of cane cut per man) was significantly correlated with the individual's estimated maximum aerobic capacity determined in the laboratory, but not with the degree of S. mansoni infection. The noninfected group was less "efficient" (mean productivity:oxygen intake) during cutting than the infected groups but a larger proportion of the noninfected were in their first season of cutting. There was a positive correlation between the number of seasons' cutting experience and the individual's age, degree of infection and mean productivity. Cane cutters studied in this investigation were a relatively fit, active population from whom the more seriously ill were excluded. These results do not, therefore necessarily reflect the effects of S. mansoni on physiological work capacity and productivity of more static populations in areas of high endemicity.

  9. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... this chapter, in raw sugar cane juice. It is added prior to clarification when further processing of the sugar cane juice must be delayed. (d) The additive is applied to the sugar juice in the following...

  10. VIEW OF MILL FROM KEKAHA ROAD, WITH SUGAR BIN, CANE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF MILL FROM KEKAHA ROAD, WITH SUGAR BIN, CANE CLEANING PLANT AND CRUSHING MILL TO THE FORE. VIEW FROM THE EAST - Kekaha Sugar Company, Sugar Mill Building, 8315 Kekaha Road, Kekaha, Kauai County, HI

  11. A novel approach of integrated bioprocessing of cane molasses for production of prebiotic and functional bioproducts.

    PubMed

    Sharma, Manisha; Patel, Satya Narayan; Lata, Kusum; Singh, Umesh; Krishania, Meena; Sangwan, Rajender S; Singh, Sudhir P

    2016-11-01

    In this work, the sugar industry by-product cane molasses was investigated as feedstock for acceptor reactions by dextransucrase from Leuconostoc mesenteroides MTCC 10508, leading to the biosynthesis of oligosaccharides. The starch industry corn fiber residue was used as a source for acceptor molecules, maltose, in the reaction. Production of approximately 124g oligosaccharides (DP3-DP6) per kg of fresh molasses was achieved. Further, cane molasses based medium was demonstrated as a sole carbon source for L. mesenteroides growth and dextransucrase production. d-Fructose released by dextransucrase activity as processing by-product was transformed into the functional monosaccharide with zero caloric value, d-psicose, by inducing its epimerization. Quantitative analysis approximated 37g d-psicose per kg of fresh molasses. Thus, the study established a novel approach of integrated bioprocessing of cane molasses into prebiotic and functional food additives. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Sugar and Other Sweeteners

    NASA Astrophysics Data System (ADS)

    Godshall, Mary An

    Sugar and starch are among the most abundant plant products available, and large industries exist worldwide to extract and process them from agricultural sources. The world production of sugar (sucrose from cane and beet) in 2004/2005 was 142 million metric tons, raw value, 1 with 24.8 percent of that being beet sugar and 75.1 percent being cane sugar.2 The proportion of beet sugar to cane sugar has fallen steadily since about 1971, when it constituted 42.8 percent of total sugar production. The decline in total beet sugar proportion over the last ten years represents not so much a decline in beet production, which has remained in a range of 33-39 million metric tons, but rather a continued increase in cane sugar production from around 70 million metric tons in 1991 to 112 million metric tons.2 The production of total world sugar has also risen dramatically since 1971/72, when it was 71.7 million tons.3

  13. The Acceptability of Caning Children in Singapore: The Fine Line Between Discipline and Physical Maltreatment.

    PubMed

    Ngiam, Xin Ying; Tung, Serena S W

    2016-01-01

    Child maltreatment is a worldwide phenomenon with far-reaching negative consequences, and physical abuse is its most visible and widely reported form of maltreatment. There is a fine line between nonabusive physical punishment and physical child abuse, and where this line is drawn is often influenced by prevailing cultural practices and child-rearing beliefs. This article focus on Singapore-a modern Asian society that remains rooted in traditional attitudes and practices-as a case study in exploring the boundaries. In particular, the local practice of caning (hitting with a rattan cane) as a disciplinary measure for children, the ambiguity of the law on the issue of physical abuse, and the influence of judicial caning on the acceptability of this common practice are examined. Finally, the possible means of safeguarding children and discouraging the use of physical punishment in the home are discussed.

  14. Cradle-to-Gate Life-Cycle Inventory of Cellulosic Fiberboard Produced in North America

    Treesearch

    Richard D. Bergman

    2015-01-01

    Documenting the environmental performance of building products is becoming widespread because of many green marketing claims made without scientific merit (i.e., green-washing). Developing environmental product declarations (EPDs) for building products is one way to accomplish this objective for scientific documentation and to counter green-washing (ISO 2006a; Bergman...

  15. Fiberboards from loblolly pine refiner groundwood: effects of gross wood characteristics and board density

    Treesearch

    Charles W. McMillin

    1968-01-01

    Boards for insulation and and structural uses are being manufactured in increasing quantities. The coarse fiber required for these products can be disk-refined from untreated wood chips. Since such fiber is produced in essentially one mechanical operation, continuous control is required of the raw material as well as the refining process.

  16. Surface modification of lignocellulosic fibers using high-frequency ultrasound

    Treesearch

    Jayant B. Gadhe; Ram B. Gupta; Thomas Elder

    2005-01-01

    Enzymatic and chemical oxidation of fiber surfaces has been reported in the literature as a method for producing medium density fiberboards without using synthetic adhesives. This work focuses on modifying the surface properties of wood fibers by the generation of free radicals using high-frequency ultrasound. A sonochemical reactor operating at 610 kHz is used to...

  17. 49 CFR 173.171 - Smokeless powder for small arms.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... fiberboard boxes meeting the Packing Group I performance level, provided all inside containers are packed to prevent shifting and the net weight of smokeless powder in any one box does not exceed 7.3 kg (16 pounds... 45.4 kg (100 pounds) net mass in: (1) One rail car, motor vehicle, or cargo-only aircraft; or (2) One...

  18. Medium density fiberboards from plantation grown Eucalyptus saligna

    Treesearch

    Andrzej Krzysik; John A. Youngquist; James H. Muehl; Fabio Spina Franca

    1999-01-01

    The production of industrial wood from natural forests is predicted to decline in the future. Factors that will contribute to this decline include changes in land use patterns, depletion of resources in some parts of the world, and the withdrawal of forest areas from industrial production in order to provide for environmental, recreational, and other social needs....

  19. Insulating board, hardboard, and other structural fiberboards

    Treesearch

    W. C. Lewis; S. L. Schwartz

    1965-01-01

    The wood-base fiber panel materials are a part of the rapidly evolving technology based on converting lignocellulose to fiber and reconstituting the fiber into large sheets and panels. While some equipment and techniques used are the same as for producing paper, there are enough differences in techniques used and other requirements for manufacture that a separate...

  20. 49 CFR 173.187 - Pyrophoric solids, metals or alloys, n.o.s.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... positive (not friction) means of closure and contain not more than 15 kg (33 pounds) each. (c) In fiberboard boxes (4G) with inner metal receptacles which have a positive (not friction) means of closure and... (1D) with inner metal receptacles which have a positive (not friction) means of closure and contain...

  1. 49 CFR 173.187 - Pyrophoric solids, metals or alloys, n.o.s.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... positive (not friction) means of closure and contain not more than 15 kg (33 pounds) each. (c) In fiberboard boxes (4G) with inner metal receptacles which have a positive (not friction) means of closure and... (1D) with inner metal receptacles which have a positive (not friction) means of closure and contain...

  2. Comparison of postbuckling model and finite element model with compression strength of corrugated boxes

    Treesearch

    Thomas J. Urbanik; Edmond P. Saliklis

    2002-01-01

    Conventional compression strength formulas for corrugated fiberboard boxes are limited to geometry and material that produce an elastic postbuckling failure. Inelastic postbuckling can occur in squatty boxes and trays, but a mechanistic rationale for unifying observed strength data is lacking. This study employs a finite element model, instead of actual experiments, to...

  3. Wood-based panel plant locations and timber availability in selected U.S. states

    Treesearch

    T. McKeever; H. N. Spelter

    1998-01-01

    This report lists wood-based panel industry plant locations, production capacities, timber inventories, and wood costs for 24 U.S. states. Industry sectors covered include medium-density fiberboard, particleboard, softwood plywood, and oriented strandboard. Maps of major forest producing states show plant locations and the underlying density of timber stocking by...

  4. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Chloric acid solution or chlorine dioxide hydrate... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When the.... Fiberboard boxes must be reinforced and insulated and sufficient dry ice must be used to maintain the hydrate...

  5. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Chloric acid solution or chlorine dioxide hydrate... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When the.... Fiberboard boxes must be reinforced and insulated and sufficient dry ice must be used to maintain the hydrate...

  6. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Chloric acid solution or chlorine dioxide hydrate... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When the.... Fiberboard boxes must be reinforced and insulated and sufficient dry ice must be used to maintain the hydrate...

  7. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Chloric acid solution or chlorine dioxide hydrate... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When the.... Fiberboard boxes must be reinforced and insulated and sufficient dry ice must be used to maintain the hydrate...

  8. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Chloric acid solution or chlorine dioxide hydrate... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When the.... Fiberboard boxes must be reinforced and insulated and sufficient dry ice must be used to maintain the hydrate...

  9. Binderless fiberboard : comparison of fiber from recycled corrugated containers and refined small-diameter whole treetops

    Treesearch

    John F. Hunt; Karen Supan

    2006-01-01

    Whereas many research activities focus on developing value-added processes that use forest residues, scientists must also investigate the mechanical properties of products made from recycled fiber resources. This study compared the tensile and bending properties of binderless panels made from recycled corrugated containers with properties of panels made from lodgepole...

  10. Production of ethanol from xylose by Candida shehatae grown under continuous or fed-batch conditions

    Treesearch

    T. W. Jeffries; M. A. Alexander

    1990-01-01

    Xylose is a major component of angiosperm lignocellulosic residues. It is available from a number of different sources in the forest products industry, including fiberboard manufacture, sulfite waste liquors, production of dissolving pulp, and the hydrolysis of hardwood residues. Hydrolysis of wood for the production of liquid fuels, particularly ethanol, has been...

  11. Fiberboard and hardboard research at the Forest Products Laboratory : a 50-year summary

    Treesearch

    Gary C. Myers; J. Dobbin McNatt

    1985-01-01

    Many changes have occurred in the fiber-based panel products industries during the past 50 years. During this timespan the Forest Products Laboratory has conducted a considerable amount of research on processing and product evaluation of fiber-based panel product materials. Unfortunately about 26 percent of this information was never published. completed during this...

  12. Evaluation of Type II Fast Packs for Electrostatic Discharge Properties.

    DTIC Science & Technology

    1983-08-01

    34 x 8" x 1 3/4") consisting of a reclosable cushioned carrier which mates into an outer fiberboard sleeve. A cushioning insert is used consisting of a... RECLOSABLE CUSHIONED CARRIER TEST LOAD FIGURE 1: Cancel Caddy Pack * CONVOLUTED 4* CUSHIONED I FIGURE 2: Type II Fast Pack (PPP-B-1672) TYPE II FAST PACK

  13. Competition and pesticide exposure affect development of invasive (Rhinella marina) and native (Fejervarya vittigera) rice paddy amphibian larvae.

    PubMed

    Shuman-Goodier, Molly E; Singleton, Grant R; Propper, Catherine R

    2017-12-01

    Increased pesticide use in rice agricultural ecosystems may alter competitive interactions between invasive and native amphibian species. We conducted an experiment with two rice paddy amphibians found in Luzon, Philippines, the invasive cane toad (Rhinella marina) and the endemic Luzon wart frog (Fejervarya vittigera), to determine whether exposure to a common herbicide, butachlor, drives competitive interactions in favor of the invasive amphibian. Our results revealed that competition had a strong effect on the development of both species, but in opposing directions; Luzon wart frog tadpoles were smaller and developed slower than when raised alone, whereas cane toad tadpoles were larger and developed faster. Contrary to our predictions, development and survival of endemic wart frog tadpoles was not affected by butachlor, whereas invasive cane toad tadpoles were affected across several endpoints including gene expression, body size, and survival. We also observed an interaction between pesticide exposure and competition for the cane toad, where survival declined but body size and expression of thyroid sensitive genes increased. Taken together, our findings indicate that the success of the cane toad larvae in rice fields may be best explained by increased rates of development and larger body sizes of tadpoles in response to competition with native Luzon wart frog tadpoles rather than lower sensitivity to a common pesticide. Our results for the cane toad also provide evidence that butachlor can disrupt thyroid hormone mediated development in amphibians, and further demonstrate that important species interactions such as competition can be affected by pesticide exposure in aquatic ecosystems.

  14. Production and evaluation of sugar cane fiber geotextiles : report 2 : field testing.

    DOT National Transportation Integrated Search

    1997-03-01

    Prior research involved the production and laboratory testing of sugar cane fiber geotextiles for soil erosion control. Comparative preliminary studies were conducted on test slopes to determine slope stability, in horticulture plots to determine gra...

  15. Effects and feasibility of a standardised orientation and mobility training in using an identification cane for older adults with low vision: design of a randomised controlled trial.

    PubMed

    Zijlstra, G A R; van Rens, G H M B; Scherder, E J A; Brouwer, D M; van der Velde, J; Verstraten, P F J; Kempen, G I J M

    2009-08-27

    Orientation and mobility training (O&M-training) in using an identification cane, also called symbol cane, is provided to people with low vision to facilitate independent participation in the community. In The Netherlands this training is mainly practice-based because a standardised and validly evaluated O&M-training in using the identification cane is lacking. Recently a standardised O&M-training in using the identification cane was developed. This training consists of two face-to-face sessions and one telephone session during which, in addition to usual care, the client's needs regarding mobility are prioritised, and cognitive restructuring techniques, action planning and contracting are applied to facilitate the use of the cane. This paper presents the design of a randomised controlled trial aimed to evaluate this standardised O&M-training in using the identification cane in older adults with low vision. A parallel group randomised controlled trial was designed to compare the standardised O&M-training with usual care, i.e. the O&M-training commonly provided by the mobility trainer. Community-dwelling older people who ask for support at a rehabilitation centre for people with visual impairment and who are likely to receive an O&M-training in using the identification cane are included in the trial (N = 190). The primary outcomes of the effect evaluation are ADL self care and visual functioning with respect to distance activities and mobility. Secondary outcomes include quality of life, feelings of anxiety, symptoms of depression, fear of falling, and falls history. Data for the effect evaluation are collected by means of telephone interviews at baseline, and at 5 and 17 weeks after the start of the O&M-training. In addition to an effect evaluation, a process evaluation to study the feasibility of the O&M-training is carried out. The screening procedure for eligible participants started in November 2007 and will continue until October 2009. Preliminary findings regarding the evaluation are expected in the course of 2010. If the standardised O&M-training is more effective than the current O&M-training or, in case of equal effectiveness, is considered more feasible, the training will be embedded in the Dutch national instruction for mobility trainers. ClinicalTrials.gov NCT00946062.

  16. Energy balances in sugar cane, coffee and natural vegetation in the northeastern side of the São Paulo state, Brazil

    NASA Astrophysics Data System (ADS)

    de C. Teixeira, Antônio H.; Leivas, Janice F.; Ronquim, Carlos C.; Bayma-Silva, Gustavo; de C. Victoria, Daniel

    2016-10-01

    Under land and climate change scenarios, agriculture has experienced water competitions among other sectors in the São Paulo state, Brazil. On the one hand, in several occasions, in the northeastern side of this state, nowadays sugar-cane is expanding, while coffee plantations are losing space. On the other hand, both crops have replaced the natural vegetation composed by Savannah and Atlantic Coastal Forest species. Under this dynamic situation, geosciences are valuable tools for evaluating the large-scale energy and mass exchanges between these different agro-ecosystems and the lower atmosphere. For quantification of the energy balance components in these mixed agro-ecosystems, the bands 1 and 2 from the MODIS product MOD13Q1 were used throughout SAFER (Surface Algorithm for Evapotranspiration Retrieving) algorithm, which was applied together with a net of 12 automatic weather stations, during the year 2015 in the main sugar cane and coffee growing regions, located at the northeastern side of the state. The fraction of the global solar radiation (RG) transformed into net radiation (Rn) was 52% for sugar cane and 53% for both, coffee and natural vegetation. The respective annual fractions of Rn used as λE were 0.68, 0.87 and 0.77, while for the sensible heat (H) fluxes they were 0.27, 0.07 and 0.16. From April to July, heat advection raised λE values above Rn promoting negative H, however these effects were much and less strong in coffee and sugar cane crops, respectively. The smallest daily Rn fraction for all agro-ecosystems was for the soil heat flux (G), with averages of 5%, 6% and 7% in sugar cane, coffee and natural vegetation. From the energy balance analyses, we could conclude that, sugar-cane crop presented lower annual water consumption than that for coffee crop, what can be seen as an advantage in situations of water scarcity. However, the replacement of natural vegetation by sugar cane can contribute for warming the environment, while when this occur with coffee crop there was noticed cooling conditions. The large scale modeling satisfactory results confirm the suitability of using MODIS products together with weather stations to study the energy balance components in mixed agro-ecosystems under land-use and climate change conditions.

  17. Social epidemiology of a large outbreak of chickenpox in the Colombian sugar cane producer region: a set theory-based analysis.

    PubMed

    Idrovo, Alvaro J; Albavera-Hernández, Cidronio; Rodríguez-Hernández, Jorge Martín

    2011-07-01

    There are few social epidemiologic studies on chickenpox outbreaks, although previous findings suggested the important role of social determinants. This study describes the context of a large outbreak of chickenpox in the Cauca Valley region, Colombia (2003 to 2007), with an emphasis on macro-determinants. We explored the temporal trends in chickenpox incidence in 42 municipalities to identify the places with higher occurrences. We analyzed municipal characteristics (education quality, vaccination coverage, performance of health care services, violence-related immigration, and area size of planted sugar cane) through analyses based on set theory. Edwards-Venn diagrams were used to present the main findings. The results indicated that three municipalities had higher incidences and that poor quality education was the attribute most prone to a higher incidence. Potential use of set theory for exploratory outbreak analyses is discussed. It is a tool potentially useful to contrast units when only small sample sizes are available.

  18. Line-scan spatially offset Raman spectroscopy for inspecting subsurface food safety and quality

    NASA Astrophysics Data System (ADS)

    Qin, Jianwei; Chao, Kuanglin; Kim, Moon S.

    2016-05-01

    This paper presented a method for subsurface food inspection using a newly developed line-scan spatially offset Raman spectroscopy (SORS) technique. A 785 nm laser was used as a Raman excitation source. The line-shape SORS data was collected in a wavenumber range of 0-2815 cm-1 using a detection module consisting of an imaging spectrograph and a CCD camera. A layered sample, which was created by placing a plastic sheet cut from the original container on top of cane sugar, was used to test the capability for subsurface food inspection. A whole set of SORS data was acquired in an offset range of 0-36 mm (two sides of the laser) with a spatial interval of 0.07 mm. Raman spectrum from the cane sugar under the plastic sheet was resolved using self-modeling mixture analysis algorithms, demonstrating the potential of the technique for authenticating foods and ingredients through packaging. The line-scan SORS measurement technique provides a new method for subsurface inspection of food safety and quality.

  19. Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

    PubMed

    Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

    2017-06-01

    In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Polyphenolic reductants in cane sugar

    USDA-ARS?s Scientific Manuscript database

    Limited information is available to understand the chemical structure of cane sugar extracts responsible for the redox reactivity. This study employed Fremy’s salt to test the hypothesis that hydroquinone/catechol-semiquinone-quinone redox cycle is responsible for the antioxidant activity of sugarc...

  1. 17. Photocopy of c. 1922 photograph of cane field tractor ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. Photocopy of c. 1922 photograph of cane field tractor developed and patented by Mr. Arsenaud of Laurel Valley Plantation; Claiborne Toups, overseer, is standing on the left. - Laurel Valley Sugar Plantation, State Route 308, Thibodaux, Lafourche Parish, LA

  2. Fungal invertase as an aid for fermentation of cane molasses into ethanol

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Park, Y.K.; Sato, H.H.

    1982-10-01

    Comparative studies of the fermentation of cane molasses into ethanol by Saccharomyces cerevisiae in the presence or absence of fungal invertase were performed. When cane molasses was fermented by the yeast at 30 degrees Centigrade and pH 5.0, the presence of the enzyme had no effect on ethanol production. At pH 3.4, ethanol production was increased by the addition of invertase. At 40 degrees C, the addition of invertase increased ethanol production by 5.5% at pH 5.0 and by 20.9% at pH 3.5. (Refs. 8).

  3. Evaluation of the precipitation-runoff modeling system, Beaver Creek basin, Kentucky

    USGS Publications Warehouse

    Bower, D.E.

    1985-01-01

    The Precipitation Runoff Modeling System (PRMS) was evaluated with data from Cane branch and Helton Branch in the Beaver Creek basin of Kentucky. Because of previous studies, 10.6 years of record were available to establish a data base for the basin including 60 storms for Cane Branch and 50 storms for Helton Branch. The model was calibrated initially using data from the 1956-58 water years. Runoff predicted by the model was 94.7% of the observed runoff at Cane Branch (mined area) and 96.9% at Helton Branch (unmined area). After the model and data base were modified, the model was refitted to the 1956-58 data for Helton Branch. It then predicted 98.6% of the runoff for the 10.6-year period. The model parameters from Helton Branch were then used to simulate the Cane Branch runoff and discharge. The model predicted 102.6% of the observed runoff at Cane Branch for the 10.6 years. The simulations produced reasonable storm volumes and peak discharges. Sensitivity analysis of model parameters indicated the parameters associated with soil moisture are the most sensitive. The model was used to predict sediment concentration and daily sediment load for selected storm periods. The sediment computations indicated the model can be used to predict sediment concentrations during storm events. (USGS)

  4. Orientation and mobility training for partially-sighted older adults using an identification cane: a systematic review

    PubMed Central

    Ballemans, Judith; Kempen, Gertrudis IJM; Zijlstra, GA Rixt

    2011-01-01

    Objective: This study aimed to provide an overview of the development, content, feasibility, and effectiveness of existing orientation and mobility training programmes in the use of the identification cane. Data sources: A systematic bibliographic database search in PubMed, PsychInfo, ERIC, CINAHL and the Cochrane Library was performed, in combination with the expert consultation (n = 42; orientation and mobility experts), and hand-searching of reference lists. Review methods: Selection criteria included a description of the development, the content, the feasibility, or the effectiveness of orientation and mobility training in the use of the identification cane. Two reviewers independently agreed on eligibility and methodological quality. A narrative/qualitative data analysis method was applied to extract data from obtained documents. Results: The sensitive database search and hand-searching of reference lists revealed 248 potentially relevant abstracts. None met the eligibility criteria. Expert consultation resulted in the inclusion of six documents in which the information presented on the orientation and mobility training in the use of the identification cane was incomplete and of low methodological quality. Conclusion: Our review of the literature showed a lack of well-described protocols and studies on orientation and mobility training in identification cane use. PMID:21795405

  5. Measuring energetics and behaviour using accelerometry in cane toads Bufo marinus.

    PubMed

    Halsey, Lewis G; White, Craig R

    2010-04-21

    Cane toads Bufo marinus were introduced to Australia as a control agent but now have a rapidly progressing invasion front and damage new habitats they enter. Predictive models that can give expansion rates as functions of energy supply and feeding ground distribution could help to maximise control efficiency but to date no study has measured rates of field energy expenditure in an amphibian. In the present study we used the accelerometry technique to generate behavioural time budgets and, through the derivation of ODBA (overall dynamic body acceleration), to obtain estimates of energetics in free ranging cane toads. This represents the first time that accelerometers have been used to not only quantify the behaviour of animals but also assign to those behaviours rates of energy expenditure. Firstly, laboratory calibrations between ODBA and metabolic rate were obtained and used to generate a common prediction equation for the subject toads (R(2) = 0.74). Furthermore, acceleration data recorded during different behaviours was studied to ascertain threshold values for objectively defining behaviour categories. Importantly, while subsequent accelerometer field deployments were relatively short they agreed with previous studies on the proportion of time that cane toads locomote yet suggest that the metabolic rate of cane toads in the wild may sometimes be considerably higher than might be assumed based on data for other species.

  6. Effect of Harvesting Stage on Sweet Sorghum (Sorghum bicolor L.) Genotypes in Western Kenya

    PubMed Central

    Owuoche, James O.; Oyoo, Maurice E.; Cheruiyot, Erick; Mulianga, Betty

    2017-01-01

    Harvesting stage of sweet sorghum (Sorghum bicolor L. Moench) cane is an important aspect in the content of sugar for production of industrial alcohol. Four sweet sorghum genotypes were evaluated for harvesting stage in a randomized complete block design. In order to determine sorghum harvest growth stage for bioethanol production, sorghum canes were harvested at intervals of seven days after anthesis. The genotypes were evaluated at different stages of development for maximum production of bioethanol from flowering to physiological maturity. The canes were crushed and juice fermented to produce ethanol. Measurements of chlorophyll were taken at various stages as well as panicles from the harvested canes. Dried kernels at 14% moisture content were also weighed at various stages. Chlorophyll, grain weight, absolute ethanol volume, juice volume, cane yield, and brix showed significant (p = 0.05) differences for genotypes as well as the stages of harvesting. Results from this study showed that harvesting sweet sorghum at stages IV and V (104 to 117 days after planting) would be appropriate for production of kernels and ethanol. EUSS10 has the highest ethanol potential (1062.78 l ha−1) due to excellent juice volume (22976.9 l ha−1) and EUSS11 (985.26 l ha−1) due to its high brix (16.21). PMID:28255577

  7. 78 FR 45494 - Notice of Second Sugar Purchase and Exchange for Re-export Program Credits

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-29

    ... raw cane sugar to be offered in exchange for Refined Sugar Re- export Program credits as a follow-up..., 2013. CCC will invite domestic sugarcane processors to offer raw cane sugar to CCC, as authorized by...

  8. JPRS Report Science and Technology Central Eurasia: Life Sciences.

    DTIC Science & Technology

    1992-01-30

    Imperata cylindrica ), and representatives of the genus orous restoration of woody plants, enhancement of their Typha. Cane communities are capable...nology for restoring and improving them. One would the southern cane (Phragmites australis), imperata expect an improvement of forest conditions, the vig

  9. Climate and land use: Forgive us our carbon debts

    NASA Astrophysics Data System (ADS)

    Macedo, Marcia N.; Davidson, Eric A.

    2014-07-01

    Sugar cane ethanol replaces fossil fuels, but changes in soil carbon could offset some of the benefit. Now, a study shows minor loss of soil carbon when pastures and croplands are converted to cane, but larger losses when converting native savannahs.

  10. Emergency housing systems from three-dimensional engineered fiberboard : temporary building systems for lightweight, portable, easy-to-assemble, reusable, recyclable, and biodegradable structures

    Treesearch

    Jerrold E. Winandy; John F. Hunt; Christopher Turk; James R. Anderson

    2006-01-01

    Following natural disasters (such as hurricanes, tornados, or tsunamis), when civilians become displaced, or when military troops are deployed overseas, temporary housing is often a critical need. The USDA Forest Products Laboratory recently developed a lightweight, transportable, reusable, and recyclable biocomposite building material—threedimensional engineered...

  11. 49 CFR 173.171 - Smokeless powder for small arms.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... any one box (one package) must not exceed 7.3 kg (16 pounds). [Amdt. 173-224, 55 FR 52643, Dec. 21...) net mass in: (1) One rail car, motor vehicle, or cargo-only aircraft; or (2) One freight container on... inner packagings not exceeding 3.6 kg (8 pounds) net mass and outer packaging of UN 4G fiberboard boxes...

  12. Dimensional stability and decay resistance of composite fiberboard made from plantation-grown southern yellow pine

    Treesearch

    Poo Chow; Timothy Harp; John A. Youngquist; Jim H. Muehl; Andrzej M. Krzysik

    1999-01-01

    The objective of this study was to investigate the influence of the phenol-formaldehyde resin content level (3 percent and 7 percent), and three fungi species (Poria placenta, Gleophyllum trabeum, and Polyporus versicolor) on the dimensional stability and decay resistance of high density composition boards made from plantation-grown southern pine chips. A standard ASTM...

  13. Composites from southern pine juvenile wood. Part 1. Panel fabrication and initial properties

    Treesearch

    Anton D. Pugel; Eddie W. Price; Chung-Yun Hse

    1990-01-01

    Flakeboard, particleboard, and fiberboard panels were manufactured from four different sources of southern pine (Pinus taeda L.) juvenile wood. The sources were: 1) fastgrown trees; 2) the inner core of older trees; 3) branches; and 4) tops. The juvenile wood particle sizes and panel densities were similar to those used for control panels made from...

  14. 78 FR 60766 - Clarification on Fireworks Policy Regarding Approvals or Certifications for Specialty Fireworks...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-02

    ... fireworks device is a fire truck with 10 tubes, 2 grams per tube, for a total pyrotechnic weight of 20 grams... fusing; 3. May not exceed 10 fiberboard or plastic tubes per device; 4. May not contain more than 2 grams of pyrotechnic composition per tube, and not more than 20 grams pyrotechnic composition in the...

  15. Measurement of Dynamic Viscoelasticity of Full-Size Wood Composite Panels Using a Vibration Testing Method

    Treesearch

    Cheng Guan; Houjiang Zhang; John F. Hunt; Lujing Zhou; Dan Feng

    2016-01-01

    The dynamic viscoelasticity of full-size wood composite panels (WCPs) under the free-free vibrational state were determined by a vibration testing method. Vibration detection tests were performed on 194 pieces of three types of full-size WCPs (particleboard, medium density fiberboard, and plywood (PW)). The dynamic viscoelasticity from smaller specimens cut from the...

  16. Binderless fiberboard from two different types of fiber furnishes

    Treesearch

    Otto Suchsland; George Woodson; Charles W. McMillin

    1985-01-01

    Fiber furnishes from two commercial processes were used to make experimental hardboards by all four possible methods: wet formed (pressed dry and wet), and dry formed (pressed dry and wet). Since no adhesives were added, all bonding was due to natural agents. Results of mechanical and physical testing of the hardboards indicated that high quality hardboard can be made...

  17. 3D engineered fiberboard : engineering analysis of a new building product

    Treesearch

    John F. Hunt; Jerrold E. Winandy

    2003-01-01

    In many forests across the United States, the high forest fuel loadings are contributing to our recent forest fire problems. Many fire-prone timber stands are generally far from traditional timber markets or the timber is not economically valuable enough to cover the costs of removal. To help address this problem, the USDA Forest Products Laboratory has developed a...

  18. Strength and life criteria for corrugated fiberboard by three methods

    Treesearch

    Thomas J. Urbanik

    1997-01-01

    The conventional test method for determining the stacking life of corrugated containers at a fixed load level does not adequately predict a safe load when storage time is fixed. This study introduced multiple load levels and related the probability of time at failure to load. A statistical analysis of logarithm-of-time failure data varying with load level predicts the...

  19. Pressing of three-layer, dry-formed MDF with binderless hardboard faces

    Treesearch

    Otto Suchsland; George E. Woodson; Charles W. McMillin

    1986-01-01

    Severely cooked Masonite pulp was used as face material in three-layer experimental medium-density fiberboard (MDF). The core layer consisted of conventional MDF furnish with resin binder added. The faces were formed absolutely dry without additives of any kind. The three-layer mat was hot-pressed to overall densities ranging from 44 to 56 pcf. The faces had hardboard-...

  20. 49 CFR 178.502 - Identification codes for packagings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...” means a jerrican. (iv) “4” means a box. (v) “5” means a bag. (vi) “6” means a composite packaging. (vii... natural wood. (iv) “D” means plywood. (v) “F” means reconstituted wood. (vi) “G” means fiberboard. (vii... (other than steel or aluminum). (xi) “P” means glass, porcelain or stoneware. (3) A numeral indicating...

  1. 49 CFR 178.502 - Identification codes for packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...” means a jerrican. (iv) “4” means a box. (v) “5” means a bag. (vi) “6” means a composite packaging. (vii... natural wood. (iv) “D” means plywood. (v) “F” means reconstituted wood. (vi) “G” means fiberboard. (vii... (other than steel or aluminum). (xi) “P” means glass, porcelain or stoneware. (3) A numeral indicating...

  2. 49 CFR 178.502 - Identification codes for packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...” means a jerrican. (iv) “4” means a box. (v) “5” means a bag. (vi) “6” means a composite packaging. (vii... natural wood. (iv) “D” means plywood. (v) “F” means reconstituted wood. (vi) “G” means fiberboard. (vii... (other than steel or aluminum). (xi) “P” means glass, porcelain or stoneware. (3) A numeral indicating...

  3. 49 CFR 178.502 - Identification codes for packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...” means a jerrican. (iv) “4” means a box. (v) “5” means a bag. (vi) “6” means a composite packaging. (vii... natural wood. (iv) “D” means plywood. (v) “F” means reconstituted wood. (vi) “G” means fiberboard. (vii... (other than steel or aluminum). (xi) “P” means glass, porcelain or stoneware. (3) A numeral indicating...

  4. Chicken feather fiber as an additive in MDF composites

    Treesearch

    Jerrold E. Winandy; James H. Muehl; Jessie A. Glaeser; Walter Schmidt

    2007-01-01

    Medium density fiberboard (MDF) panels were made with aspen fiber and 0-95% chicken feather fiber (CFF) in 2.5%, 5%, or 25% increments, using 5% phenol formaldehyde resin as the adhesive. Panels were tested for mechanical and physical properties as well as decay. The addition of CFF decreased strength and stiffness of MDF-CFF composites compared with that of all-wood...

  5. Mechanical and physical properties of composite panels manufactured from Chinese tallow tree furnish

    Treesearch

    Todd F. Shupe; Leslie H. Groom; Thomas L. Eberhardt; Timothy G. Rials; Chung Y. Hse; Thomas Pesacreta

    2006-01-01

    Chinese tallow tree is a noxious, invasive plant in the southeastern United States. It is generally considered a nuisance and has no current commercial use. The objective of this research was to determine the technical feasibility of using the stem wood of this species for particleboard, fiberboard, and structural flakeboard. Due to its rapid growth, Chinese tallow...

  6. 7 CFR 1435.302 - Establishment of allotments.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.302 Establishment of allotments. (a) By the beginning of the crop year, CCC will establish the overall allotment quantity, beet sugar and cane sugar allotments, State cane sugar allotments...

  7. 7 CFR 1435.302 - Establishment of allotments.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.302 Establishment of allotments. (a) By the beginning of the crop year, CCC will establish the overall allotment quantity, beet sugar and cane sugar allotments, State cane sugar allotments...

  8. Cultural Resources Investigations of Larose to Golden Meadow Hurricane Protection Project Levee Section D-North (Compromise Alignment), Lafourche Parish, Louisiana

    DTIC Science & Technology

    1992-03-01

    marsh. Other characteristic species include roseau cane (Phragmites communis), bulltongue (Sagittaria lancifolia), coastal water hyssop ( Bacopa monnien...Spartina patens), roseau cane (Phragmites communis), coastal water hyssop ( Bacopa monnien), coontail (Ceratophyllum demursum), fragrant flatsedge

  9. 7 CFR 1435.302 - Establishment of allotments.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.302 Establishment of allotments. (a) By the beginning of the crop year, CCC will establish the overall allotment quantity, beet sugar and cane sugar allotments, State cane sugar allotments...

  10. 7 CFR 1435.302 - Establishment of allotments.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.302 Establishment of allotments. (a) By the beginning of the crop year, CCC will establish the overall allotment quantity, beet sugar and cane sugar allotments, State cane sugar allotments...

  11. 7 CFR 1435.302 - Establishment of allotments.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.302 Establishment of allotments. (a) By the beginning of the crop year, CCC will establish the overall allotment quantity, beet sugar and cane sugar allotments, State cane sugar allotments...

  12. Biomass Yield and Carbohydrate Composition in Sugarcane and Energy Cane

    USDA-ARS?s Scientific Manuscript database

    Sugarcane and energy cane are important crops for sugar and bio-ethanol production. A better understanding their carbohydrate composition and concentrations in addition to biomass yields can improve knowledge in biomass processing and utilization. There were two objectives for this study. The first ...

  13. Use of Slag/Sugar Cane Bagasse Ash (SCBA) Blends in the Production of Alkali-Activated Materials

    PubMed Central

    Castaldelli, Vinícius N.; Akasaki, Jorge L.; Melges, José L.P.; Tashima, Mauro M.; Soriano, Lourdes; Borrachero, María V.; Monzó, José; Payá, Jordi

    2013-01-01

    Blast furnace slag (BFS)/sugar cane bagasse ash (SCBA) blends were assessed for the production of alkali-activated pastes and mortars. SCBA was collected from a lagoon in which wastes from a sugar cane industry were poured. After previous dry and grinding processes, SCBA was chemically characterized: it had a large percentage of organic matter (ca. 25%). Solutions of sodium hydroxide and sodium silicate were used as activating reagents. Different BFS/SCBA mixtures were studied, replacing part of the BFS by SCBA from 0 to 40% by weight. The mechanical strength of mortar was measured, obtaining values about 60 MPa of compressive strength for BFS/SCBA systems after 270 days of curing at 20 °C. Also, microstructural properties were assessed by means of SEM, TGA, XRD, pH, electrical conductivity, FTIR spectroscopy and MIP. Results showed a good stability of matrices developed by means of alkali-activation. It was demonstrated that sugar cane bagasse ash is an interesting source for preparing alkali-activated binders. PMID:28811425

  14. Microbial and chemical contamination of water, sediment and soil in the Nakivubo wetland area in Kampala, Uganda.

    PubMed

    Fuhrimann, Samuel; Stalder, Michelle; Winkler, Mirko S; Niwagaba, Charles B; Babu, Mohammed; Masaba, Godfrey; Kabatereine, Narcis B; Halage, Abdullah A; Schneeberger, Pierre H H; Utzinger, Jürg; Cissé, Guéladio

    2015-07-01

    The reuse of domestic and industrial wastewater in urban settings of the developing world may harm the health of people through direct contact or via contaminated urban agricultural products and drinking water. We assessed chemical and microbial pollutants in 23 sentinel sites along the wastewater and faecal sludge management and reuse chain of Kampala, Uganda. Water samples were examined for bacteria (thermotolerant coliforms (TTCs), Escherichia coli and Salmonella spp.) and helminth eggs. Physico-chemical parameters were determined. Water, sediment and soil samples and edible plants (yams and sugar cane) were tested for heavy metals. Water samples derived from the Nakivubo wetland showed mean concentrations of TTCs of 2.9 × 10(5) colony-forming units (CFU)/100 mL. Mean E. coli was 9.9 × 10(4) CFU/100 mL. Hookworm eggs were found in 13.5% of the water samples. Mean concentrations of iron (Fe), copper (Cu) and cadmium (Cd) were 21.5, 3.3 and 0.14 mg/L, respectively. In soil samples, we found a mean lead (Pb) concentration of 132.7 mg/L. In yams, concentrations of Cd, chromium (Cr) and Pb were 4.4, 4.0 and 0.2 mg/L, while the respective concentrations in sugar cane were 8.4, 4.3 and 0.2 mg/L. TTCs and E. coli in the water, Pb in soil, and Cd, Cr and Pb in the plants were above national thresholds. We conclude that there is considerable environmental pollution in the Nakivubo wetland and the Lake Victoria ecosystem in Kampala. Our findings have important public health implications, and we suggest that a system of sentinel surveillance is being implemented that, in turn, can guide adequate responses.

  15. Breeding Energy Cane Cultivars as a Biomass Feedstock for Coal Replacement

    USDA-ARS?s Scientific Manuscript database

    Research and advanced breeding have demonstrated that energy cane possesses all of the attributes desirable in a biofuel feedstock: extremely good biomass yield in a small farming footprint; negative/neutral carbon footprint; maximum outputs from minimum inputs; well-established growing model for fa...

  16. 40 CFR 409.31 - Specialized definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  17. 40 CFR 409.31 - Specialized definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  18. 40 CFR 409.31 - Specialized definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  19. 40 CFR 409.31 - Specialized definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

  20. Exploratory behavior of a native anuran species with high invasive potential.

    PubMed

    Miller, Amanda J; Page, Rachel A; Bernal, Ximena E

    2018-01-01

    Exploratory behavior can be a key component of survival in novel or changing environments, ultimately determining population establishment. While many studies have investigated the behavior of wild animals in response to novel food items or objects, our understanding of how they explore novel environments is limited. Here, we examine how experience affects the foraging behavior of a species with high invasive potential. In particular, we investigate the movement and behavior of cane toads as a function of experience in a novel environment, and how the presence of food modulates exploration. Cane toads, from a population in their native range, were repeatedly tested in a large, naturalistic arena with or without food present. Both groups exhibited significant but different changes in exploratory behavior. While toads in an environment without food reduced exploratory behavior over trials, those with food present increased both food intake per trial and the directness of their paths to food, resulting in fewer approaches to food patches over time. Our results suggest that cane toads learn patch location and provide preliminary evidence suggesting toads use spatial memory, not associative learning, to locate food. In sum, we show that with experience, cane toads alter their behavior to increase foraging efficiency. This study emphasizes the role of learning in foraging in cane toads, a characteristic that may have facilitated their success as invaders.

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top