Hybrid 2D photonic crystal-assisted Lu3Al5O12:Ce ceramic-plate phosphor and free-standing red film phosphor for white LEDs with high color-rendering index.

PubMed

Park, Hoo Keun; Oh, Ji Hye; Kang, Heejoon; Zhang, Jian; Do, Young Rag

2015-03-04

This paper reports the combined optical effects of a two-dimensional (2D) SiNx photonic crystal layer (PCL)-assisted Lu3Al5O12:Ce (LuAG:Ce) green ceramic-plate phosphor (CPP) and a free-standing (Sr,Ca)AlSiN3:Eu red film phosphor to enhance luminous efficacy, color rendering index (CRI), and special CRI (R9) of LuAG:Ce CPP-capped white light-emitting diodes (LEDs) for high-power white LEDs at 350 mA. By introducing the 2D SiNx PCL, the luminous efficacy was improved by a factor of 1.25 and 1.15 compared to that of the conventional flat CPP-capped LED and the thickness-increased CPP-capped LED (with a thickness of 0.15 mm), respectively, while maintaining low color-rendering properties. The combining of the free-standing red film phosphor in the flat CPP-capped, the 2D PCL-assisted CPP-capped, and the thickness-increased CPP-capped LEDs led to enhancement of the CRI and the special CRI (R9); it also led to a decrease of the correlated color temperature (CCT) due to broad wavelength coverage via the addition of red emission. High CRI (94), natural white CCT (4450 K), and acceptable luminous efficacy (71.1 lm/W) were attained from the 2D PCL-assisted LuAG:Ce CPP/free-standing red film phosphor-based LED using a red phosphor concentration of 7.5 wt %. It is expected that the combination of the 2D PCL and the free-standing red film phosphor will be a good candidate for achieving a high-power white CPP-capped LED with excellent CRI.

Free-standing 3D polyaniline-CNT/Ni-fiber hybrid electrodes for high-performance supercapacitors

NASA Astrophysics Data System (ADS)

Li, Yuan; Fang, Yuzhu; Liu, Hong; Wu, Xiaoming; Lu, Yong

2012-04-01

Free-standing 3D macroscopic polyaniline (PANi)-carbon nanotube (CNT)-nickel fiber hybrids have been developed, and they deliver high specific capacitance (725 F g-1 at 0.5 A g-1) and high energy density at high rates (~22 W h kg-1 at 2000 W kg-1, based on total electrode mass) with good cyclability.Free-standing 3D macroscopic polyaniline (PANi)-carbon nanotube (CNT)-nickel fiber hybrids have been developed, and they deliver high specific capacitance (725 F g-1 at 0.5 A g-1) and high energy density at high rates (~22 W h kg-1 at 2000 W kg-1, based on total electrode mass) with good cyclability. Electronic supplementary information (ESI) available: Experimental details on preparation, characterization, and electrochemical testing; Fig. S1-S8, Schemes S1 and S2. See DOI: 10.1039/c2nr30252g

Measurement of three-dimensional posture and trajectory of lower body during standing long jumping utilizing body-mounted sensors.

PubMed

Ibata, Yuki; Kitamura, Seiji; Motoi, Kosuke; Sagawa, Koichi

2013-01-01

The measurement method of three-dimensional posture and flying trajectory of lower body during jumping motion using body-mounted wireless inertial measurement units (WIMU) is introduced. The WIMU is composed of three-dimensional (3D) accelerometer and gyroscope of two kinds with different dynamic range and one 3D geomagnetic sensor to adapt to quick movement. Three WIMUs are mounted under the chest, right thigh and right shank. Thin film pressure sensors are connected to the shank WIMU and are installed under right heel and tiptoe to distinguish the state of the body motion between grounding and jumping. Initial and final postures of trunk, thigh and shank at standing-still are obtained using gravitational acceleration and geomagnetism. The posture of body is determined using the 3D direction of each segment updated by the numerical integration of angular velocity. Flying motion is detected from pressure sensors and 3D flying trajectory is derived by the double integration of trunk acceleration applying the 3D velocity of trunk at takeoff. Standing long jump experiments are performed and experimental results show that the joint angle and flying trajectory agree with the actual motion measured by the optical motion capture system.

5. "TEST STAND 13, CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. "TEST STAND 1-3, CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications No. OC12-50-10; Drawing No. 60-09-06; no sheet number within title block. D.O. SERIES 1109/17, Rev. A. Stamped: AS BUILT; NO CHANGES. Date of Revision A: 11/1/50. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-3, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Inflight exercise affects stand test responses after space flight

NASA Technical Reports Server (NTRS)

Lee, S. M.; Moore, A. D. Jr; Fritsch-Yelle, J. M.; Greenisen, M. C.; Schneider, S. M.

1999-01-01

PURPOSE: The purpose of this study was to determine whether exercise performed by Space Shuttle crew members during short-duration space flights (9-16 d) affects the heart rate (HR) and blood pressure (BP) responses to standing within 2-4 h of landing. METHODS: Thirty crew members performed self-selected inflight exercise and maintained exercise logs to monitor their exercise intensity and duration. Two subjects participated in this investigation during two different flights. A 10-min stand test, preceded by at least 6 min of quiet supine rest, was completed 10-15 d before launch (PRE) and within 4 h of landing (POST). Based upon their inflight exercise records, subjects were grouped as either high (HIex: > or = 3 times/week, HR > or = 70% HRmax, > or = 20 min/session, N = 11), medium (MEDex: > or = 3 times/week, HR < 70% HRmax, > or = 20 min/session, N = 10), or low (LOex: < or = 3 times/week, HR and duration variable, N = 11) exercisers. HR and BP responses to standing were compared between groups (ANOVA, P < or = 0.05). RESULTS: There were no PRE differences between the groups in supine or standing HR and BP. Although POST supine HR was similar to PRE, all groups had an increased standing HR compared with PRE. The increase in HR upon standing was significantly greater after flight in the LOex group (36 +/- 5 bpm) compared with HIex or MEDex groups (25 +/- 1 bpm; 22 +/- 2 bpm). Similarly, the decrease in pulse pressure (PP) from supine to standing was unchanged after space flight in the MEDex and HIex groups but was significantly greater in the LOex group (PRE: -9 +/- 3; POST: -19 +/- 4 mm Hg). CONCLUSIONS: Thus, moderate to high levels of inflight exercise attenuated HR and PP responses to standing after space flight.

Single- and Dual-Task Balance Training Are Equally Effective in Youth

PubMed Central

Lüder, Benjamin; Kiss, Rainer; Granacher, Urs

2018-01-01

Due to maturation of the postural control system and secular declines in motor performance, adolescents experience deficits in postural control during standing and walking while concurrently performing cognitive interference tasks. Thus, adequately designed balance training programs may help to counteract these deficits. While the general effectiveness of youth balance training is well-documented, there is hardly any information available on the specific effects of single-task (ST) versus dual-task (DT) balance training. Therefore, the objectives of this study were (i) to examine static/dynamic balance performance under ST and DT conditions in adolescents and (ii) to study the effects of ST versus DT balance training on static/dynamic balance under ST and DT conditions in adolescents. Twenty-eight healthy girls and boys aged 12–13 years were randomly assigned to either 8 weeks of ST or DT balance training. Before and after training, postural sway and spatio-temporal gait parameters were registered under ST (standing/walking only) and DT conditions (standing/walking while concurrently performing an arithmetic task). At baseline, significantly slower gait speed (p < 0.001, d = 5.1), shorter stride length (p < 0.001, d = 4.8), and longer stride time (p < 0.001, d = 3.8) were found for DT compared to ST walking but not standing. Training resulted in significant pre–post decreases in DT costs for gait velocity (p < 0.001, d = 3.1), stride length (-45%, p < 0.001, d = 2.4), and stride time (-44%, p < 0.01, d = 1.9). Training did not induce any significant changes (p > 0.05, d = 0–0.1) in DT costs for all parameters of secondary task performance during standing and walking. Training produced significant pre–post increases (p = 0.001; d = 1.47) in secondary task performance while sitting. The observed increase was significantly greater for the ST training group (p = 0.04; d = 0.81). For standing, no significant changes were found over time irrespective of the experimental group. We conclude that adolescents showed impaired DT compared to ST walking but not standing. ST and DT balance training resulted in significant and similar changes in DT costs during walking. Thus, there appears to be no preference for either ST or DT balance training in adolescents. PMID:29928248

Single- and Dual-Task Balance Training Are Equally Effective in Youth.

PubMed

Lüder, Benjamin; Kiss, Rainer; Granacher, Urs

2018-01-01

Due to maturation of the postural control system and secular declines in motor performance, adolescents experience deficits in postural control during standing and walking while concurrently performing cognitive interference tasks. Thus, adequately designed balance training programs may help to counteract these deficits. While the general effectiveness of youth balance training is well-documented, there is hardly any information available on the specific effects of single-task (ST) versus dual-task (DT) balance training. Therefore, the objectives of this study were (i) to examine static/dynamic balance performance under ST and DT conditions in adolescents and (ii) to study the effects of ST versus DT balance training on static/dynamic balance under ST and DT conditions in adolescents. Twenty-eight healthy girls and boys aged 12-13 years were randomly assigned to either 8 weeks of ST or DT balance training. Before and after training, postural sway and spatio-temporal gait parameters were registered under ST (standing/walking only) and DT conditions (standing/walking while concurrently performing an arithmetic task). At baseline, significantly slower gait speed ( p < 0.001, d = 5.1), shorter stride length ( p < 0.001, d = 4.8), and longer stride time ( p < 0.001, d = 3.8) were found for DT compared to ST walking but not standing. Training resulted in significant pre-post decreases in DT costs for gait velocity ( p < 0.001, d = 3.1), stride length (-45%, p < 0.001, d = 2.4), and stride time (-44%, p < 0.01, d = 1.9). Training did not induce any significant changes ( p > 0.05, d = 0-0.1) in DT costs for all parameters of secondary task performance during standing and walking. Training produced significant pre-post increases ( p = 0.001; d = 1.47) in secondary task performance while sitting. The observed increase was significantly greater for the ST training group ( p = 0.04; d = 0.81). For standing, no significant changes were found over time irrespective of the experimental group. We conclude that adolescents showed impaired DT compared to ST walking but not standing. ST and DT balance training resulted in significant and similar changes in DT costs during walking. Thus, there appears to be no preference for either ST or DT balance training in adolescents.

Flexible, cathodoluminescent and free standing mesoporous silica films with entrapped quasi-2D perovskites

NASA Astrophysics Data System (ADS)

Vassilakopoulou, Anastasia; Papadatos, Dionysios; Koutselas, Ioannis

2017-04-01

The effective entrapment of hybrid organic-inorganic semiconductors (HOIS) into mesoporous polymer-silica hybrid matrices, formed as free standing flexible films, is presented for the first time. A blend of quasi-2D HOIS, simply synthesized by mixing two-dimensional (2D) and three dimensional (3D) HOIS, exhibiting strong photoluminescence, is embedded into porous silica matrices during the sol-gel synthesis, using tetraethylorthosilicate as precursor and Pluronic F-127 triblock copolymer as structure directing agent, under acidic conditions. The final nanostructure hybrid forms flexible, free standing films, presenting high cathodoluminescence and long stable excitonic luminescence, indicating the protective character of the hybrid matrix towards the entrapped perovskite. A significant result is that the photoluminescence of the entrapped HOIS is not affected even after films' prolonged exposure to water.

Cardiac autonomic function in children with type 1 diabetes.

PubMed

Metwalley, Kotb Abbass; Hamed, Sherifa Ahmed; Farghaly, Hekma Saad

2018-06-01

Cardiovascular autonomic neuropathy (CAN) is a major complication of type 1 diabetes (T1D). This study aimed to evaluate cardiac autonomic nervous system (ANS) function in children with T1D and its relation to different demographic, clinical and laboratory variable. This cross-sectional study included 60 children with T1D (mean age = 15.1 ± 3.3 years; duration of diabetes = 7.95 ± 3.83 years). The following 8 non-invasive autonomic testing were used for evaluation: heart rate at rest and in response to active standing (30:15 ratio), deep breathing and Valsalva maneuver (indicating parasympathetic function); blood pressure response to standing (orthostatic hypotension or OH), sustained handgrip and cold; and heart rate response to standing or positional orthostatic tachycardia syndrome or POTs (indicating sympathetic function). None had clinically manifest CAN. Compared to healthy children (5%), 36.67% of children with T1D had ≥ 2 abnormal tests (i.e., CAN) (P = 0.0001) which included significantly abnormal heart rate response to standing (POTs) (P = 0.052), active standing (30:15 ratio) (P = 0.0001) and Valsalva maneuver (P = 0.0001), indicating parasympathetic autonomic dysfunction, and blood pressure response to cold (P = 0.01), indicating sympathetic autonomic dysfunction. 54.55, 27.27 and 18.18% had early, definite and severe dysfunction of ANS. All patients had sensorimotor peripheral neuropathy. The longer duration of diabetes (> 5 years), presence of diabetic complications and worse glycemic control were significantly associated with CAN. The study concluded that both parasympathetic and sympathetic autonomic dysfunctions are common in children with T1D particularly with longer duration of diabetes and presence of microvascular complications. What is Known: • Cardiovascular autonomic neuropathy (CAN) is a major complication of type 1 diabetes (T1D). • Limited studies evaluated CAN in children with T1D. What is New: • CAN is common in children with T1D. • Cardiac autonomic functions should be assessed in children with T1D particularly in presence of microvascular complications.

A 3D heterogeneous FeTiO3/TiO2@C fiber membrane as a self-standing anode for power Li-ion battery

NASA Astrophysics Data System (ADS)

Li, Jing-quan; Jing, Mao-xiang; Han, Chong; Yao, Shan-shan; Zhai, Hong-ai; Chen, Li-li; Shen, Xiang-qian; Xiao, Ke-song

2018-04-01

A three-dimensional (3D) networking FeTiO3/TiO2@C flexible fiber membrane was successfully fabricated by an electrospinning process and a controlled hot-press sintering method. This FeTiO3/TiO2@C fiber membrane displays a long-range continuous conductive networks, which can be directly used as self-standing anodes. The electrode sintered at 750 °C for 3 h possesses a reversible capacity of 205.4 mAh/g after 100 cycles at a current density of 300 mA/g. The superior cycle and rate performance can be attributed to the synergistic effect of little volume variation of TiO2 matrix, high capacity of FeTiO3 and good electrical conductivity of 3D networking.

Analysis of the Pelvic Functional Orientation in the Sagittal Plane: A Radiographic Study With EOS 2D/3D Technology.

PubMed

Loppini, Mattia; Longo, Umile Giuseppe; Ragucci, Pasquala; Trenti, Nicoletta; Balzarini, Luca; Grappiolo, Guido

2017-03-01

We investigated the relationship between pelvic incidence (PI) with anterior pelvic plane angle (APPA), pelvic tilt (PT) angle, and sacral slope (SS) in standing and sitting positions to identify the best parameter expressing the pelvic functional orientation in the sagittal plane. We enrolled 109 consecutive patients (M:F = 43:66) eligible for a primary total hip arthroplasty (THA) with an average age of 63.4 years (15-85). EOS 2D/3D radiography was performed in standing and sitting positions before THA to evaluate the functional pelvic orientation. 3D images took into account the patient-specific sagittal balance measuring APPA, PT, SS, and PI. In standing position, functional parameters measured 5° ± 7.1 for APPA, 11° ± 8.3 for PT, 43° ± 8.5 for SS, and 53° ± 10.9 for PI. In sitting position, they were -18° ± 10.4 for APPA, 34° ± 11.8 for PT, 20° ± 12.6 for SS, and 54° ± 10.9 for PI. There was no significant difference between men and women in terms of the functional parameters in both positions. No relationship was found between APPA and PI in both positions. SS correlated with PI in standing (r = 0.66; P < .0001; R 2  = 0.44) and sitting (r = 0.51; P < .0001; R 2  = 0.26). PT correlated with PI in standing (r = 0.65; P < .0001; R 2  = 0.42) and sitting (r = 0.38; P < .0001; R 2  = 0.14). SS shows the highest correlation with functional pelvic tilt. The study suggests that adjustments in acetabular anteversion during primary THA should be based on SS. Copyright © 2016 Elsevier Inc. All rights reserved.

4. "TEST STAND NO. 13, CONCRETE STRUCTURAL PLAN AND ELEVATION." ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. "TEST STAND NO. 1-3, CONCRETE STRUCTURAL PLAN AND ELEVATION." Specifications No. OC11-50-10; Drawing No. 60-09-06; no sheet number within title block. D.O. SERIES 1109/12 REV. E. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04-353 Eng. 177, Rev. E; Date: 17 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-3, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

6. "TEST STAND NO. 13, RETAINING WALLS & APRON, SECTIONS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. "TEST STAND NO. 1-3, RETAINING WALLS & APRON, SECTIONS & ELEVATIONS." Specifications No. OC11-50-10; Drawing No. 60-09-06; no sheet number within title block. D.O. SERIES 1109/20, Rev. B. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04-353 Eng. 177, Rev. B; Date: 26 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-3, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Reversible Self-Assembly of 3D Architectures Actuated by Responsive Polymers.

PubMed

Zhang, Cheng; Su, Jheng-Wun; Deng, Heng; Xie, Yunchao; Yan, Zheng; Lin, Jian

2017-11-29

An assembly of three-dimensional (3D) architectures with defined configurations has important applications in broad areas. Among various approaches of constructing 3D structures, a stress-driven assembly provides the capabilities of creating 3D architectures in a broad range of functional materials with unique merits. However, 3D architectures built via previous methods are simple, irreversible, or not free-standing. Furthermore, the substrates employed for the assembly remain flat, thus not involved as parts of the final 3D architectures. Herein, we report a reversible self-assembly of various free-standing 3D architectures actuated by the self-folding of smart polymer substrates with programmed geometries. The strategically designed polymer substrates can respond to external stimuli, such as organic solvents, to initiate the 3D assembly process and subsequently become the parts of the final 3D architectures. The self-assembly process is highly controllable via origami and kirigami designs patterned by direct laser writing. Self-assembled geometries include 3D architectures such as "flower", "rainbow", "sunglasses", "box", "pyramid", "grating", and "armchair". The reported self-assembly also shows wide applicability to various materials including epoxy, polyimide, laser-induced graphene, and metal films. The device examples include 3D architectures integrated with a micro light-emitting diode and a flex sensor, indicting the potential applications in soft robotics, bioelectronics, microelectromechanical systems, and others.

Stand Parameters of a 27-Year-Old Water Oak Plantation on Old Field Loessial Soils

Treesearch

Roger M. Krinard; Robert L. Johnson

1988-01-01

At age 27, water oak (Quercus nigra L.) plantings on Macon Ridge old field loessial soil near Winnsboro, Louisiana, had per-acre stand values as follows: number of trees, 356; average d.b.h., 6.6 inches; basal area, 86 ft2; total volume from the stump to the tip (of trees with d.b.h. 25.0 in), 2,017 ft3...

High Energy Density All Solid State Asymmetric Pseudocapacitors Based on Free Standing Reduced Graphene Oxide-Co3O4 Composite Aerogel Electrodes.

PubMed

Ghosh, Debasis; Lim, Joonwon; Narayan, Rekha; Kim, Sang Ouk

2016-08-31

Modern flexible consumer electronics require efficient energy storage devices with flexible free-standing electrodes. We report a simple and cost-effective route to a graphene-based composite aerogel encapsulating metal oxide nanoparticles for high energy density, free-standing, binder-free flexible pseudocapacitive electrodes. Hydrothermally synthesized Co3O4 nanoparticles are successfully housed inside the microporous graphene aerogel network during the room temperature interfacial gelation at the Zn surface. The resultant three-dimensional (3D) rGO-Co3O4 composite aerogel shows mesoporous quasiparallel layer stack morphology with a high loading of Co3O4, which offers numerous channels for ion transport and a 3D interconnected network for high electrical conductivity. All solid state asymmetric pseudocapacitors employing the composite aerogel electrodes have demonstrated high areal energy density of 35.92 μWh/cm(2) and power density of 17.79 mW/cm(2) accompanied by excellent cycle life.

Physical Performance and Serum 25(OH)vitamin D Status in Community Dwelling Old Mobility Limited Adults: A Cross-Sectional Study.

PubMed

von Berens, Å; Cederholm, T; Fielding, R A; Gustafsson, T; Kirn, D; Laussen, J; Nydahl, M; Travison, T G; Reid, K; Koochek, A

2018-01-01

To examine the potential association between serum 25(OH) vitamin D and the performance on the Short Physical Performance Battery (SPPB) including the sub-components; five repeated chair stands test, 4 meters walk test and balance in older mobility-limited community-dwelling men and women. A cross sectional study was performed in American and Swedish subjects who were examined for potential participation in a combined exercise and nutrition intervention trial. Logistic regression analysis and linear regression analyses were performed to evaluate the association for 25(OH)D with the overall score on the SBBP, chair stand, gait speed and balance. Community-dwelling (mean age 77.6 ± 5.3 years) mobility limited American (n=494) and Swedish (n=116) females (59%) and males. The SPPB (0-12 points) includes chair stand (s), gait speed (m/s) and a balance test. Mobility limitation i.e., SPPB score ≤ 9 was an inclusion criterion. A blood sample was obtained to measure serum 25(OH)vitamin D concentrations. No clear association of 25(OH)D with SPPB scores was detected either when 25(OH)D was assessed as a continuous variable or when categorized according to serum concentrations of <50, 50-75 or <75 nmol/L. However, when analyzing the relationship between 25(OH)D and seconds to perform the chair stands, a significant quadratic relationship was observed. Thus, at serum levels of 25(OH)D above 74 nmol/L, higher concentrations appeared to be advantageous for the chair stand test, whereas for serum levels below 74 nmol/L this association was not observed. This cross- sectional study lacked clear association between serum 25(OH)D and physical performance in mobility limited adults. A potentially interesting observation was that at higher serum levels of 25(OH)D a better performance on the chair stand test was indicated.

Photographic copy of site plan for proposed Test Stand "D" ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of site plan for proposed Test Stand "D" in 1958. The contemporary site plans of test stands "A," "B," and "C" are also visible, along with the interconnecting tunnel system. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering "Site Plan for Proposed Test Stand "D" - Edwards Test Station," drawing no. ESP/22-0, 14 November 1958 - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Credit BG. View looking northeast at southwestern side of Test ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. View looking northeast at southwestern side of Test Stand "D" complex. Test Stand "D" workshop (Building 4222/E-23) is at left; shed to its immediate right is an entrance to underground tunnel system which interconnects all test stands. To the right of Test Stand "D" tower are four Clayton water-tube flash boilers once used in the Steam Generator Plant 4280/E-81 to power the vacuum ejector system at "D" and "C" stands. A corner of 4280/E-81 appears behind the boilers. Boilers were removed as part of stand dismantling program. The Dv (vertical vacuum) Test Cell is located in the Test Stand "D" tower, behind the sunscreen on the west side. The top of the tower contains a hoist for lifting or lowering rocket engines into the Dv Cell. Other equipment mounted in the tower is part of the steam-driven vacuum ejector system - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Validity of the microsoft kinect system in assessment of compensatory stepping behavior during standing and treadmill walking.

PubMed

Shani, Guy; Shapiro, Amir; Oded, Goldstein; Dima, Kagan; Melzer, Itshak

2017-01-01

Rapid compensatory stepping plays an important role in preventing falls when balance is lost; however, these responses cannot be accurately quantified in the clinic. The Microsoft Kinect™ system provides real-time anatomical landmark position data in three dimensions (3D), which may bridge this gap. Compensatory stepping reactions were evoked in 8 young adults by a sudden platform horizontal motion on which the subject stood or walked on a treadmill. The movements were recorded with both a 3D-APAS motion capture and Microsoft Kinect™ systems. The outcome measures consisted of compensatory step times (milliseconds) and length (centimeters). The average values of two standing and walking trials for Microsoft Kinect™ and the 3D-APAS systems were compared using t -test, Pearson's correlation, Altman-bland plots, and the average difference of root mean square error (RMSE) of joint position. The Microsoft Kinect™ had high correlations for the compensatory step times ( r  = 0.75-0.78, p  = 0.04) during standing and moderate correlations for walking ( r  = 0.53-0.63, p  = 0.05). The step length, however had a very high correlations for both standing and walking ( r  > 0.97, p  = 0.01). The RMSE showed acceptable differences during the perturbation trials with smallest relative error in anterior-posterior direction (2-3%) and the highest in the vertical direction (11-13%). No systematic bias were evident in the Bland and Altman graphs. The Microsoft Kinect™ system provides comparable data to a video-based 3D motion analysis system when assessing step length and less accurate but still clinically acceptable for step times during balance recovery when balance is lost and fall is initiated.

Efficacy of verbenone for protecting ponderosa pine stands from western pine beetle (Coleoptera: Curculionidae: Scolytinae) attack in California.

PubMed

Fettig, Christopher J; McKelvey, Stephen R; Borys, Robert R; Dabney, Christopher P; Hamud, Shakeeb M; Nelson, Lori J; Seybold, Steven J

2009-10-01

The western pine beetle, Dendroctonus brevicomis LeConte (Coleoptera: Curculionidae: Scolytinae), is a major cause of ponderosa pine, Pinus ponderosa Dougl. ex Laws., mortality in much of western North America. Currently, techniques for managing D. brevicomis infestations are limited. Verbenone (4,6,6-trimethylbicyclo [3.1.1] hept-3-en-2-one) is an antiaggregation pheromone of several Dendroctonus spp., including D. brevicomis, and it has been registered as a biopesticide for control of mountain pine beetle, Dendroctonus ponderosae Hopkins, and southern pine beetle, Dendroctonus frontalis Zimmermann. We evaluated the efficacy of a 5-g verbenone pouch [82%-(-); 50 mg/d] applied at 125 Ulha for protecting P. ponderosa stands (2 ha) from D. brevicomis attack over a 3-yr period. No significant differences in levels of D. brevicomis-caused tree mortality or the percentage of unsuccessfully attacked trees were found between verbenone-treated and untreated plots during each year or cumulatively over the 3-yr period. Laboratory analyses of release rates and chemical composition of volatiles emanating from verbenone pouches after field exposure found no deterioration of the active ingredient or physical malfunction of the release device. The mean release rate of pouches from all locations and exposure periods was 44.5 mg/d. In a trapping bioassay, the range of inhibition of the 5-g verbenone pouch was determined to be statistically constant 2 m from the release device. We discuss the implications of these and other results to the development of verbenone as a semiochemical-based tool for management of D. brevicomis infestations in P. ponderosa stands.

Visualizing Terrestrial and Aquatic Systems in 3-D

EPA Science Inventory

The environmental modeling community has a long-standing need for affordable, easy-to-use tools that support 3-D visualization of complex spatial and temporal model output. The Visualization of Terrestrial and Aquatic Systems project (VISTAS) aims to help scientists produce effe...

Development and analysis of SRIC harvesting systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stokes, B.J.; Hartsough, B.R.

1993-12-31

This paper reviews several machine combinations for harvesting short-rotation, intensive-culture (SRIC) plantations. Productivity and cost information for individual machines was obtained from published sources. Three felling and skidding systems were analyzed for two stands, a 7.6-cm (3-in) average d.b.h. sycamore and a 15.2-cm (6-in) average d.b.h. eucalyptus. The analyses assumed that whole trees were chipped at roadside. Costs and production were summarized for each system. The systems were: (1) Continuous-travel feller-buncher, skidder, and chipper; (2) 3-wheel feller-buncher, skidder, and chipper; (3) chainsaw, skidder, and chipper. In the 7.6-cm stand, system productivities were 9.9, 7.3, and 7.5 BDLT/SMH, and costs weremore » $20.9, $20.8, and $18.0 per BDLT for the three systems, respectively. System production rates for the 15.2-cm stand were 24.3, 10.2, and 12.5 BDLT/SMH, and costs were $8.7, $10.9, and $13.2 for systems 1, 2 and 3, respectively.« less

Free-standing three-dimensional graphene/manganese oxide hybrids as binder-free electrode materials for energy storage applications.

PubMed

Zhu, Xiaoli; Zhang, Peng; Xu, Shan; Yan, Xingbin; Xue, Qunji

2014-07-23

Novel three-dimensional (3D) hybrid materials, i.e., free-standing 3D graphene-supported MnO2 nanosheets, are prepared by a simple and controllable solution-phase assembly process. Characterization results show that MnO2 nanosheets are uniformly anchored on a 3D graphene framework with strong adhesion and the integral hybrids show desirable mechanical strength. Such unique structure of 3D graphene/MnO2 hybrids thus provides the right characteristics of binder-free electrode materials and could enable the design of different kinds of high-performance energy storage devices. Especially, an advanced asymmetric supercapacitor is built by using a 3D graphene/MnO2 hybrid and a 3D graphene as two electrodes, and it is able to work reversibly in a full operation voltage region of 0-3.5 V in an ionic liquid electrolyte and thus exhibits a high energy density of 68.4 Wh/kg. As the cathode materials for Li-O2 and Li-MnO2 batteries, the 3D graphene/MnO2 hybrids exhibit outstanding performances, including good catalytic capability, high reversible capacity and desirable cycling stability. The results presented here may pave a way for new promising applications of such 3D graphene/MnO2 hybrids in advanced electrochemical energy storage devices.

Use of 3d Technologies Within the Conservation of the Ancient Windows of the Basilica of S. Sabina in Rome. Construction of Exhibition Stands in Carbon Composite on a Milled Structure

NASA Astrophysics Data System (ADS)

Iaccarino Idelson, A.; Pannuzi, S.; Brunetto, A.; Galanti, G.; Giovannone, C.; Massa, V.; Serino, C.; Vischetti, F.

2017-05-01

Rare and precious window elements from the Paleochristian Basilica of Saint Sabina in Rome, made of plaster gypsum with translucent selenite used as glass for light transmission, were discovered by Antonio Muñoz during the restoration of the building at the beginning of the 20th c. Originally standing within the stone window frame, were then mounted on wood planks with screws for holding together the scattered fragments. The surfaces were covered with grime and the selenite elements were blinded by the wooden supports. During the recent conservation treatment at ISCR, traces of Egyptian blue on the internal surfaces were detected. Cleaning with laser allowed their conservation and the removal of gypsum deposits from the fragile selenite. 3-D scanning was performed for milling, out of polystyrene blocks, the counterforms that were needed for turning the artifacts upside down. After cleaning and re-assembling of the fragments, a new 3-D scan was performed to obtain a complete model of the artifacts that was used to define the best orientation of the windows, both for exhibition purposes and for the distribution of the weight-related stresses. Following a project based on 3-D modeling, exhibition stands were produced with a core material milled out of PET foam, reinforced with outer skins made with carbon fiber adhered under vacuum to the core material with epoxy resin. The new exhibition stands, very light and rigid, permit all-round appreciation of the artifacts and allow the light to shine through the selenite elements.

[Causation between occupational prolonged standing time during progestation and pregnancy related complications].

PubMed

Weng, Ting-ting; Xu, Ye-qing; Yan, Shuang-qin; Pan, Wei-jun; Tao, Fang-biao

2013-06-01

To describe the epidemiological characteristics of profession related long-standing behavior during preconception and progestation, and to probe the relationship between prolonged standing jobs and the common pregnancy related complications among pregnant women, in Ma' anshan city,Anhui province. In this cohort study, subjects who had their first antenatal examination at Ma' anshan Maternal and Child Care Centers were recruited under informed consent, from October 2008 to October 2010. All the information were collected through questionnaires in the first, second and third trimesters respectively. Three questionnaires were filled in by subjects under the guidance of healthcare takers. In the study, the 75(th) percentile of prolonged-standing times were 4.0 h/d and 3.0 h/d respectively in preconception and progestation. The characteristics of pregnant women with low social/economic status, prone to be involved in stand-long occupation. Results in logistic regression analysis, prolonged-standing jobs during preconception was the risk factor of pregnancy-induced hypertension and severe anemia. The adjusted odds ratios were 2.05 (95%CI:1.26-3.31) and 1.38(95%CI:1.03-1.85)respectively. Prolonged standing jobs appeared to be common occupational exposure to and risks of both pregnant woman and their fetus. Exposure to these kinds of jobs during preconception could increase the risk of pregnancy-induced hypertension and severe anemia. In order to promote maternal health programs, all the related occupational risk factors should be valued and avoided during preconception and pregnancy.

Space allowance influences individually housed Holstein bull calf innate immune measures and standing behaviors after castration at 3 weeks of age.

PubMed

Calvo-Lorenzo, M S; Hulbert, L E; Ballou, M A; Fowler, A L; Luo, Y; Klasing, K C; Mitloehner, F M

2017-03-01

Dairy calves in the Southwest regions of the United States are typically raised individually in wooden hutches with 1.23 m 2 of space. The objective of the study was to determine if increased space allowance in wooden hutches influences measures of innate immunity and behaviors of Holstein bull calves pre- and postcastration. Calves were randomly assigned at 4 d of age to conventional (CONV; 1.23 m 2 of space; n = 18), moderate (MOD; 1.85 m 2 space; n = 17), or maximized space allowance (MAX; 3.71 m 2 space; n = 19) in hutches. Calves were surgically castrated at 24 d of age. Peripheral whole blood samples were collected at -1, +1, +5, and +12 d of castration. Accelerometer loggers (n = 16 calves per treatment) were used from -3 to +5 d of castration to assess standing behaviors. All calves decreased total standing duration the day of castration versus precastration. Overall, MAX spent the most time in the stand position postcastration versus CONV and MOD. Within treatments, MOD and MAX had increased plasma cortisol 1 d postcastration versus precastration. A treatment × time tendency was observed for cortisol at 12 d postcastration; MAX had the least circulating cortisol. A treatment × time tendency for circulating haptoglobin (Hp) was observed and Hp was greatest among CONV 1 d pre- and 12 d postcastration. Compared with precastration, CONV had increased Hp at 1, 5, and 12 d, whereas MOD had increased Hp at 5 d, and Hp remained similar within MAX. A treatment × time tendency for tumor necrosis factor-α (TNF-α) from lipopolysaccharide-stimulated whole blood was observed; at 1 d postcastration, MOD had the most TNF-α, whereas MAX had the least. Within MAX, calves had increased TNF-α from precastration to 5 d postcastration. A treatment × time interaction was observed for whole blood bactericidal activity against Escherichia coli (WB anti-E). The CONV tended to have the greatest WB anti-E at d -1, but at d 1 and 5 postcastration, CONV had the least WB anti-E. Overall, MAX had less intensity of neutrophil oxidative burst versus CONV and MOD. The lower response of neutrophil oxidative burst and slower Hp secretion after castration is indicative that the wound site likely had less microbial exposure. The findings of this study suggest that calves housed with more space are potentially at less risk of too much inflammation after castration, which may likely be due to the effects of increased space on hide cleanliness and increased standing time. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

1. CAPTIVE TEST STAND D1 FROM THE FERROCEMENT APRON, VIEW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. CAPTIVE TEST STAND D-1 FROM THE FERROCEMENT APRON, VIEW TOWARDS SOUTHEAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-1, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

2. CLOSE UP OF CAPTIVE TEST STAND D4, VIEW TOWARDS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. CLOSE UP OF CAPTIVE TEST STAND D-4, VIEW TOWARDS NORTHEAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-4, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

1. CAPTIVE TEST STAND D4, CONNECTING TUNNELS AT RIGHT, VIEW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. CAPTIVE TEST STAND D-4, CONNECTING TUNNELS AT RIGHT, VIEW TOWARDS NORTHEAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-4, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Three-Dimensional Printing Based Hybrid Manufacturing of Microfluidic Devices.

PubMed

Alapan, Yunus; Hasan, Muhammad Noman; Shen, Richang; Gurkan, Umut A

2015-05-01

Microfluidic platforms offer revolutionary and practical solutions to challenging problems in biology and medicine. Even though traditional micro/nanofabrication technologies expedited the emergence of the microfluidics field, recent advances in advanced additive manufacturing hold significant potential for single-step, stand-alone microfluidic device fabrication. One such technology, which holds a significant promise for next generation microsystem fabrication is three-dimensional (3D) printing. Presently, building 3D printed stand-alone microfluidic devices with fully embedded microchannels for applications in biology and medicine has the following challenges: (i) limitations in achievable design complexity, (ii) need for a wider variety of transparent materials, (iii) limited z-resolution, (iv) absence of extremely smooth surface finish, and (v) limitations in precision fabrication of hollow and void sections with extremely high surface area to volume ratio. We developed a new way to fabricate stand-alone microfluidic devices with integrated manifolds and embedded microchannels by utilizing a 3D printing and laser micromachined lamination based hybrid manufacturing approach. In this new fabrication method, we exploit the minimized fabrication steps enabled by 3D printing, and reduced assembly complexities facilitated by laser micromachined lamination method. The new hybrid fabrication method enables key features for advanced microfluidic system architecture: (i) increased design complexity in 3D, (ii) improved control over microflow behavior in all three directions and in multiple layers, (iii) transverse multilayer flow and precisely integrated flow distribution, and (iv) enhanced transparency for high resolution imaging and analysis. Hybrid manufacturing approaches hold great potential in advancing microfluidic device fabrication in terms of standardization, fast production, and user-independent manufacturing.

Three-Dimensional Printing Based Hybrid Manufacturing of Microfluidic Devices

PubMed Central

Shen, Richang; Gurkan, Umut A.

2016-01-01

Microfluidic platforms offer revolutionary and practical solutions to challenging problems in biology and medicine. Even though traditional micro/nanofabrication technologies expedited the emergence of the microfluidics field, recent advances in advanced additive manufacturing hold significant potential for single-step, stand-alone microfluidic device fabrication. One such technology, which holds a significant promise for next generation microsystem fabrication is three-dimensional (3D) printing. Presently, building 3D printed stand-alone microfluidic devices with fully embedded microchannels for applications in biology and medicine has the following challenges: (i) limitations in achievable design complexity, (ii) need for a wider variety of transparent materials, (iii) limited z-resolution, (iv) absence of extremely smooth surface finish, and (v) limitations in precision fabrication of hollow and void sections with extremely high surface area to volume ratio. We developed a new way to fabricate stand-alone microfluidic devices with integrated manifolds and embedded microchannels by utilizing a 3D printing and laser micromachined lamination based hybrid manufacturing approach. In this new fabrication method, we exploit the minimized fabrication steps enabled by 3D printing, and reduced assembly complexities facilitated by laser micromachined lamination method. The new hybrid fabrication method enables key features for advanced microfluidic system architecture: (i) increased design complexity in 3D, (ii) improved control over microflow behavior in all three directions and in multiple layers, (iii) transverse multilayer flow and precisely integrated flow distribution, and (iv) enhanced transparency for high resolution imaging and analysis. Hybrid manufacturing approaches hold great potential in advancing microfluidic device fabrication in terms of standardization, fast production, and user-independent manufacturing. PMID:27512530

Response of a poor-site western redcedar stand to precommercial thinning and fertilization.

Treesearch

Constance A. Harrington; Charles A. Wierman

1985-01-01

Seven silvicultural treatments were applied in a 20-year-old natural western red-cedar (Thuja plicata) Donn ex D. Don) stand on a poor site in coastal Washington: (1) control (unthinned, unfertilized); (2) unthinned, fertilized with ammonium nitrate, monodicalcium phosphate, and potassium sulfate; (3) thinned, unfertilized; (4) thinned, fertilized...

Analytical and multibody modeling for the power analysis of standing jumps.

PubMed

Palmieri, G; Callegari, M; Fioretti, S

2015-01-01

Two methods for the power analysis of standing jumps are proposed and compared in this article. The first method is based on a simple analytical formulation which requires as input the coordinates of the center of gravity in three specified instants of the jump. The second method is based on a multibody model that simulates the jumps processing the data obtained by a three-dimensional (3D) motion capture system and the dynamometric measurements obtained by the force platforms. The multibody model is developed with OpenSim, an open-source software which provides tools for the kinematic and dynamic analyses of 3D human body models. The study is focused on two of the typical tests used to evaluate the muscular activity of lower limbs, which are the counter movement jump and the standing long jump. The comparison between the results obtained by the two methods confirms that the proposed analytical formulation is correct and represents a simple tool suitable for a preliminary analysis of total mechanical work and the mean power exerted in standing jumps.

Credit BG. View looking southwest at Test Stand "D" complex. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. View looking southwest at Test Stand "D" complex. In the background at left is the Steam Generator Plant 4280/E-81 built in 1972 to house four gas-fired Clayton flash boilers. The boilers were later supplemented by the electrically heated steam accumulator (sphere) to supply steam to the various ejectors at Test Stand "D" vacuum test cells - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Flooring in front of the feed bunk affects feeding behavior and use of freestalls by dairy cows.

PubMed

Tucker, C B; Weary, D M; de Passillé, A M; Campbell, B; Rushen, J

2006-06-01

In 2 experiments we assessed how preferences, time budgets, and feeding behavior of dairy cows change in response to flooring surfaces in front of the feed bunk. In Experiment 1, 12 nonlactating dairy cattle were individually housed with access to 2 standing platforms filled with either concrete or sawdust. In Experiment 2, 24 nonlactating dairy cattle were given access to either concrete or Animat rubber flooring in front of the feed bunk. In Experiment 1, cows preferred the sawdust to the concrete flooring. In both experiments, cows provided with a softer floor in front of the feed bunk spent more time standing near the feed bunk without eating (Experiment 1: 67 vs. 40 min/d on sawdust vs. concrete, respectively, SEM = 5.6 min/d; Experiment 2: 176 vs. 115 min/d on Animat vs. concrete, respectively, SEM = 20.5 min/d) compared with when they were kept on concrete. The increased time spent at the feed bunk was due to a combination of more frequent eating and standing bouts, indicating that cows were more willing to move on nonconcrete flooring. Total time spent eating was significantly greater on the softer floor in Experiment 2, but not in Experiment 1 (Exp. 1: 289 vs. 275 min/d on sawdust and concrete, respectively, SEM = 7.3 min/d; Exp. 2: 330 vs. 289 min/d on Animat and concrete, respectively, SEM = 15.4), although feed intake was increased on the sawdust treatment in Experiment 1. Cows spent significantly more time lying in the feed alley when the flooring was rubber (219 vs. 53 min/d on Animat and concrete, SEM = 53.6 min/d), perhaps because the lying area in Experiment 2 was inadequate. In conclusion, cows prefer to stand on softer flooring in front of the feed bunk, and are more willing to move on and spend more time standing in front of the feed bunk when provided with softer flooring. These results indicate that cows find softer flooring surfaces more comfortable to stand on than concrete, and highlight the importance of evaluating the comfort of the entire facility.

Gender differences of foot characteristics in older Japanese adults using a 3D foot scanner.

PubMed

Saghazadeh, Mahshid; Kitano, Naruki; Okura, Tomohiro

2015-01-01

Knowledge of gender differences in foot shape assists shoe manufactures with designing appropriate shoes for men and women. Although gender differences in foot shapes are relatively known among young men and women, less is known about how the older men and women's feet differ in shape. A recent development in foot shape assessment is the use of 3D foot scanners. To our knowledge this technology has yet to be used to examine gender differences in foot shape of Japanese older adults. This cross-sectional study included 151 older men (74.5 ± 5.6 years) and 140 older women (73.9 ± 5.1 years) recruited in Kasama City, Japan. Foot variables were measured in sitting and standing positions using Dream GP Incorporated's 3D foot scanner, Footstep PRO (Osaka, Japan). Scores were analyzed as both raw and normalized to truncated foot length using independent samples t-test and analysis of covariance, respectively. In men, the measurement values for navicular height, first and fifth toe and instep heights, ball and heel width, ball girth, arch height index (just standing), arch rigidity index and instep girth were significantly greater than the women's, whereas the first toe angle, in both sitting and standing positions was significantly smaller. However, after normalizing, the differences in ball width, heel width, height of first and fifth toes in both sitting and standing and ball girth in sitting position were nonsignificant. According to Cohen's d, among all the foot variables, the following had large effect sizes in both sitting and standing positions: truncated foot length, instep, navicular height, foot length, ball girth, ball width, heel width and instep girth. This study provides evidence of anthropometric foot variations between older men and women. These differences need to be considered when manufacturing shoes for older adults.

Credit BG. Test Stand "D" tower as seen looking northeast ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. Test Stand "D" tower as seen looking northeast (See caption for CA-163-F-18). To the right of the view is the stainless steel dome top for Dv Cell (see CA-163-F-22 for view into cell), behind which rests a spherical accumulator--an electrically heated steam generator for powering the vacuum system at "C" and Test Stand "D." Part of the ejector system can be seen on the right corner of the tower, other connections include electrical ducts (thin, flat metal members) and fire protection systems. Note the stand in the foreground with lights used to indicate safety status of the stand during tests - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Doping and controllable pore size enhanced electrochemical performance of free-standing 3D graphene films

NASA Astrophysics Data System (ADS)

Wang, Liping; Qin, Kaiqiang; Li, Jiajun; Zhao, Naiqin; Shi, Chunsheng; Ma, Liying; He, Chunnian; He, Fang; Liu, Enzuo

2018-01-01

High quality free-standing 3D nanoporous graphene (3DNG) films were fabricated using nanoporous nickel as template and catalyst. The effect of heteroatom doping and pore size on the electrochemical performance of the 3D graphene films as supercapacitor electrodes are systematically studied. Compared with macroporous graphene films, nanoporous graphene films exhibit an extraordinarily large operational window in neutral, acidic and alkaline aqueous electrolytes, as well as high packing density. Nitrogen and oxygen doping play different roles in different aqueous electrolytes on the electrical conductivity and pseudocapacitance of 3DNG. The realization of both high packing density, 3.65 mg/cm2, and the maximum working window, as well as the synergistic effect between N and O doping, gives rise to a high areal capacitance of 435 mF/cm2 in neutral electrolyte and excellent cycle stability up to 5000 cycles. The results provide a potential strategy to further increase the volumetric or areal energy density of carbon-based aqueous supercapacitor.

Long-term stand growth of interior ponderosa pine stands in response to structural modifications and burning treatments in northeastern California

Treesearch

Justin S. Crotteau; Martin W. Ritchie

2014-01-01

The Blacks Mountain Experimental Research Project created two distinct overstory structural classes (high structural diversity [HiD]; low-structural diversity [LoD]) across 12 stands and subsequently burned half of each stand. We analyzed stand-level growth 10 years after treatment and then modeled individual tree growth to forecast stand-level growth 10–20 years after...

Nondestructive analysis of three-dimensional objects using a fluid displacement method

USDA-ARS?s Scientific Manuscript database

Quantification of three-dimensional (3-D) objects has been a real challenge in agricultural, hydrological and environmental studies. We designed and tested a method that is capable of quantifying 3-D objects using measurements of fluid displacement. The device consists of a stand that supports a mov...

Practical alignment method for X-ray spectral measurement in micro-CT system based on 3D printing technology.

PubMed

Ren, Liqiang; Wu, Di; Li, Yuhua; Zheng, Bin; Chen, Yong; Yang, Kai; Liu, Hong

2016-06-01

This study presents a practical alignment method for X-ray spectral measurement in a rotating gantry based micro-computed tomography (micro-CT) system using three-dimensional (3D) printing technology. In order to facilitate the spectrometer placement inside the gantry, supporting structures including a cover and a stand were dedicatedly designed and printed using a 3D printer. According to the relative position between the spectrometer and the stand, the upright projection of the spectrometer collimator onto the stand was determined and then marked by a tungsten pinhole. Thus, a visible alignment indicator of the X-ray central beam and the spectrometer collimator represented by the pinhole was established in the micro-CT live mode. Then, a rough alignment could be achieved through repeatedly adjusting and imaging the stand until the pinhole was located at the center of the acquired projection image. With the spectrometer being positioned back onto the stand, the precise alignment was completed by slightly translating the spectrometer-stand assembly around the rough location, until finding a "sweet spot" with the highest photon rate and proper distribution of the X-ray photons in the resultant spectrum. The spectra were acquired under precise alignment and misalignment of approximately 0.2, 0.5, and 1.0mm away from the precise alignment position, and then were compared in qualitative and quantitative analyses. Qualitative analysis results show that, with slight misalignment, the photon rate is reduced from 1302 to 1098, 1031, and 416 photons/second (p/s), respectively, and the characteristic peaks in the acquired spectra are gradually deteriorated. Quantitative analysis indicates that the energy resolutions for characteristic peak of K α1 were calculated as 1.56% for precise alignment, while were 1.84% and 2.40% for slight misalignment of 0.2mm and 0.5mm. The mean energies were reduced from 43.93keV under precise alignment condition to 40.97, 39.63 and 37.78keV when misaligned. Accurate spectral measurements in micro-CT systems are significantly influenced by the alignment precision. This practical alignment method using 3D printing technology could be readily applied to other rotating gantry based micro-CT systems with modified design of the supporting structures and careful considerations of the spectrometer and gantry dimensions.

Practical alignment method for X-ray spectral measurement in micro-CT system based on 3D printing technology

PubMed Central

Ren, Liqiang; Wu, Di; Li, Yuhua; Zheng, Bin; Chen, Yong; Yang, Kai; Liu, Hong

2016-01-01

This study presents a practical alignment method for X-ray spectral measurement in a rotating gantry based micro-computed tomography (micro-CT) system using three-dimensional (3D) printing technology. In order to facilitate the spectrometer placement inside the gantry, supporting structures including a cover and a stand were dedicatedly designed and printed using a 3D printer. According to the relative position between the spectrometer and the stand, the upright projection of the spectrometer collimator onto the stand was determined and then marked by a tungsten pinhole. Thus, a visible alignment indicator of the X-ray central beam and the spectrometer collimator represented by the pinhole was established in the micro-CT live mode. Then, a rough alignment could be achieved through repeatedly adjusting and imaging the stand until the pinhole was located at the center of the acquired projection image. With the spectrometer being positioned back onto the stand, the precise alignment was completed by slightly translating the spectrometer-stand assembly around the rough location, until finding a “sweet spot” with the highest photon rate and proper distribution of the X-ray photons in the resultant spectrum. The spectra were acquired under precise alignment and misalignment of approximately 0.2, 0.5, and 1.0mm away from the precise alignment position, and then were compared in qualitative and quantitative analyses. Qualitative analysis results show that, with slight misalignment, the photon rate is reduced from 1302 to 1098, 1031, and 416 photons/second (p/s), respectively, and the characteristic peaks in the acquired spectra are gradually deteriorated. Quantitative analysis indicates that the energy resolutions for characteristic peak of Kα1 were calculated as 1.56% for precise alignment, while were 1.84% and 2.40% for slight misalignment of 0.2mm and 0.5mm. The mean energies were reduced from 43.93keV under precise alignment condition to 40.97, 39.63 and 37.78keV when misaligned. Accurate spectral measurements in micro-CT systems are significantly influenced by the alignment precision. This practical alignment method using 3D printing technology could be readily applied to other rotating gantry based micro-CT systems with modified design of the supporting structures and careful considerations of the spectrometer and gantry dimensions. PMID:27777787

11. "TEST STANDS NOS. 11, 13, & 15; CONCRETE STRUCTURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. "TEST STANDS NOS. 1-1, 1-3, & 1-5; CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications No. OC12-50-10; Drawing No. 60-09-04; no sheet number within title block. D.O. SERIES 1109/15, Rev. E. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04353 Eng. 177, Rev. E; Date: 21 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

15. "TEST STANDS NOS. 11, 13, & 15; STRUCTURAL STEEL; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. "TEST STANDS NOS. 1-1, 1-3, & 1-5; STRUCTURAL STEEL; PLAN & DETAILS." Specifications No. ENG 04-353-50-10; Drawing No. 60-09-04; no sheet number within title block. D.O. SERIES 1109/34, Rev. A. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04353 Eng. 177, Rev. A, no change; Date: 21 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

9. "TEST STANDS NOS. 11, 13, & 15; CONCRETE STRUCTURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. "TEST STANDS NOS. 1-1, 1-3, & 1-5; CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications No. ENG 04-35350-10; Drawing No. 60-09-04; no sheet number within title block. D.O. SERIES 1109/13. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04353 Eng. 177, no change; Date: 17 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

10. "TEST STANDS NOS. 11, 13, & 15; CONCRETE STRUCTURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. "TEST STANDS NOS. 1-1, 1-3, & 1-5; CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications No. OC12-50-10; Drawing No. 60-09-04; no sheet number within title block. D.O. SERIES 1109/14, Rev. B. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04353 Eng. 177, Rev. B; Date: 21 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

16. "TEST STANDS NOS. 11, 13, & 15; STRUCTURAL STEEL; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. "TEST STANDS NOS. 1-1, 1-3, & 1-5; STRUCTURAL STEEL; ELEVATIONS AND SECTIONS." Specifications No. ENG 04353-50-10; Drawing No. 60-09-04; no sheet number within title block. D.O. SERIES 1109/35, Rev. A. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04-353 Eng. 177, Rev. A; Date: 29 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

12. "TEST STANDS NOS. 11, 13, & 15; CONCRETE STRUCTURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. "TEST STANDS NOS. 1-1, 1-3, & 1-5; CONCRETE STRUCTURAL SECTIONS AND DETAILS." Specifications No. OC12-50-10; Drawing No. 60-09-06; no sheet number within title block. D.O. SERIES 1109/16, Rev. E. Stamped: RECORD DRAWING - AS CONSTRUCTED. Below stamp: Contract DA-04353 Eng. 177, Rev. E; Date: 26 Dec. 1951. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-5, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Models for Predicting the Biomass of Cunninghamialanceolata Trees and Stands in Southeastern China

PubMed Central

Saeed, Sajjad

2017-01-01

Using existing equations to estimate the biomass of a single tree or a forest stand still involves large uncertainties. In this study, we developed individual-tree biomass models for Chinese Fir (Cunninghamia lanceolata.) stands in Fujian Province, southeast China, by using 74 previously established models that have been most commonly used to estimate tree biomass. We selected the best fit models and modified them. The results showed that the published model ln(B(Biomass)) = a + b * ln(D) + c * (ln(H))2 + d * (ln(H))3 + e * ln(WD) had the best fit for estimating the tree biomass of Chinese Fir stands. Furthermore, we observed that variables D(diameter at breast height), H (height), and WD(wood density)were significantly correlated with the total tree biomass estimation model. As a result, a natural logarithm structure gave the best estimates for the tree biomass structure. Finally, when a multi-step improvement on tree biomass model was performed, the tree biomass model with Tree volume(TV), WD and biomass wood density conversion factor (BECF),achieved the highest simulation accuracy, expressed as ln(TB) = −0.0703 + 0.9780 * ln(TV) + 0.0213 * ln(WD) + 1.0166 * ln(BECF). Therefore, when TV, WD and BECF were combined with tree biomass volume coefficient bi for Chinese Fir, the stand biomass (SB)model included both volume(SV) and coefficient bi variables of the stand as follows: bi = Exp(−0.0703+0.9780*ln(TV)+0.0213 * ln(WD)+1.0166*ln(BECF)). The stand biomass model is SB = SV/TV * bi. PMID:28095512

Models for Predicting the Biomass of Cunninghamialanceolata Trees and Stands in Southeastern China.

PubMed

Guangyi, Mei; Yujun, Sun; Saeed, Sajjad

2017-01-01

Using existing equations to estimate the biomass of a single tree or a forest stand still involves large uncertainties. In this study, we developed individual-tree biomass models for Chinese Fir (Cunninghamia lanceolata.) stands in Fujian Province, southeast China, by using 74 previously established models that have been most commonly used to estimate tree biomass. We selected the best fit models and modified them. The results showed that the published model ln(B(Biomass)) = a + b * ln(D) + c * (ln(H))2 + d * (ln(H))3 + e * ln(WD) had the best fit for estimating the tree biomass of Chinese Fir stands. Furthermore, we observed that variables D(diameter at breast height), H (height), and WD(wood density)were significantly correlated with the total tree biomass estimation model. As a result, a natural logarithm structure gave the best estimates for the tree biomass structure. Finally, when a multi-step improvement on tree biomass model was performed, the tree biomass model with Tree volume(TV), WD and biomass wood density conversion factor (BECF),achieved the highest simulation accuracy, expressed as ln(TB) = -0.0703 + 0.9780 * ln(TV) + 0.0213 * ln(WD) + 1.0166 * ln(BECF). Therefore, when TV, WD and BECF were combined with tree biomass volume coefficient bi for Chinese Fir, the stand biomass (SB)model included both volume(SV) and coefficient bi variables of the stand as follows: bi = Exp(-0.0703+0.9780*ln(TV)+0.0213 * ln(WD)+1.0166*ln(BECF)). The stand biomass model is SB = SV/TV * bi.

Credit BG. View west of Test Stand "D" complex, with ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. View west of Test Stand "D" complex, with ends of Dd (left) and Dy (right) station ejectors in view. Steam piping from accumulator (sphere) to ejectors is apparent; long horizontal loops in the pipes permit expansion and contraction without special joints. The small platform straddling the Dd ejector (near the accumulator) was originally constructed for a "Hyprox" steam generator which supplied steam to the Dd ejector before the accumulator and Dy stand were built. Note ejectors on top of interstage condenser in Test Stand "D" tower. Metal shed in far right background is for storage - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Circulating IGF-I and IGFBP3 Levels Control Human Colonic Stem Cell Function and Are Disrupted in Diabetic Enteropathy.

PubMed

D'Addio, Francesca; La Rosa, Stefano; Maestroni, Anna; Jung, Peter; Orsenigo, Elena; Ben Nasr, Moufida; Tezza, Sara; Bassi, Roberto; Finzi, Giovanna; Marando, Alessandro; Vergani, Andrea; Frego, Roberto; Albarello, Luca; Andolfo, Annapaola; Manuguerra, Roberta; Viale, Edi; Staudacher, Carlo; Corradi, Domenico; Batlle, Eduard; Breault, David; Secchi, Antonio; Folli, Franco; Fiorina, Paolo

2015-10-01

The role of circulating factors in regulating colonic stem cells (CoSCs) and colonic epithelial homeostasis is unclear. Individuals with long-standing type 1 diabetes (T1D) frequently have intestinal symptoms, termed diabetic enteropathy (DE), though its etiology is unknown. Here, we report that T1D patients with DE exhibit abnormalities in their intestinal mucosa and CoSCs, which fail to generate in vitro mini-guts. Proteomic profiling of T1D+DE patient serum revealed altered levels of insulin-like growth factor 1 (IGF-I) and its binding protein 3 (IGFBP3). IGFBP3 prevented in vitro growth of patient-derived organoids via binding its receptor TMEM219, in an IGF-I-independent manner, and disrupted in vivo CoSC function in a preclinical DE model. Restoration of normoglycemia in patients with long-standing T1D via kidney-pancreas transplantation or in diabetic mice by treatment with an ecto-TMEM219 recombinant protein normalized circulating IGF-I/IGFBP3 levels and reestablished CoSC homeostasis. These findings demonstrate that peripheral IGF-I/IGFBP3 controls CoSCs and their dysfunction in DE. Copyright © 2015 Elsevier Inc. All rights reserved.

Circulating IGF-I and IGFBP3 levels control human colonic stem cell function and are disrupted in diabetic enteropathy

PubMed Central

Maestroni, Anna; Jung, Peter; Orsenigo, Elena; Nasr, Moufida Ben; Tezza, Sara; Bassi, Roberto; Finzi, Giovanna; Marando, Alessandro; Vergani, Andrea; Frego, Roberto; Albarello, Luca; Andolfo, Annapaola; Manuguerra, Roberta; Viale, Edi; Staudacher, Carlo; Corradi, Domenico; Batlle, Eduard; Breault, David; Secchi, Antonio; Folli, Franco; Fiorina, Paolo

2016-01-01

Summary The role of circulating factors in regulating colonic stem cells (CoSCs) and colonic epithelial homeostasis is unclear. Individuals with long-standing type 1 diabetes (T1D) frequently have intestinal symptoms, termed diabetic enteropathy (DE), though its etiology is unknown. Here, we report T1D patients with DE exhibit abnormalities in their intestinal mucosa and CoSCs, which fail to generate in vitro mini-guts. Proteomic profiling of T1D+DE patient serum revealed altered levels of insulin-like growth factor 1 (IGF-1) and its binding protein-3 (IGFBP3). IGFBP3 prevented in vitro growth of patient-derived organoids via binding its receptor TMEM219, in an IGF-1-independent manner, and disrupted in vivo CoSC function in a preclinical DE model. Restoration of normoglycemia in patients with long-standing T1D via kidney-pancreas transplantation or in diabetic mice by treatment with an ecto-TMEM219 recombinant protein normalized circulating IGF-1/IGFBP3 levels and reestablished CoSC homeostasis. These findings demonstrate that peripheral IGF-1/IGFBP3 control CoSCs and their dysfunction in DE. PMID:26431183

1. TEST AREA 1115, SOUTH PART OF SUPPORT COMPLEX, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. TEST AREA 1-115, SOUTH PART OF SUPPORT COMPLEX, LOOKING TO EAST FROM ABOVE BUILDING 8655, THE FUEL STORAGE TANK FARM, IN FOREGROUND SHADOW. AT THE RIGHT IS BUILDING 8660, ELECTRICAL SUBSTATION; TO ITS LEFT IS BUILDING 8663, THE HELIUM COMPRESSION PLANT. THE LIGHT TONED STRUCTURE IN THE MIDDLE DISTANCE, CENTER, IS THE MACHINE SHOP FOR TEST STAND 1-3. IN THE FAR DISTANCE IS TEST STAND 1-A, WITH THE WHITE SPHERICAL TANKS, AND TEST STAND 2-A TO ITS RIGHT. ALONG THE HORIZON FROM FAR LEFT ARE TEST STAND 1-D, TEST STAND 1-C, WATER TANKS ABOVE TEST AREA 1-125, AND TEST STAND 1-B IN TEST AREA 1-120. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Leuhman Ridge near Highways 58 & 395, Boron, Kern County, CA

32 CFR 242.9 - Academic, intellectual, and personal requirements for admission to advanced standing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... schools will be eligible for transfer. (c) Individuals who have received the D.D.S., D.M.D., Ph.D., D.O.... Advanced standing applicants are required to have taken the Medical College Admission Test. ...

32 CFR 242.9 - Academic, intellectual, and personal requirements for admission to advanced standing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... schools will be eligible for transfer. (c) Individuals who have received the D.D.S., D.M.D., Ph.D., D.O.... Advanced standing applicants are required to have taken the Medical College Admission Test. ...

32 CFR 242.9 - Academic, intellectual, and personal requirements for admission to advanced standing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... schools will be eligible for transfer. (c) Individuals who have received the D.D.S., D.M.D., Ph.D., D.O.... Advanced standing applicants are required to have taken the Medical College Admission Test. ...

32 CFR 242.9 - Academic, intellectual, and personal requirements for admission to advanced standing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... schools will be eligible for transfer. (c) Individuals who have received the D.D.S., D.M.D., Ph.D., D.O.... Advanced standing applicants are required to have taken the Medical College Admission Test. ...

26 CFR 1.411(d)-3 - Section 411(d)(6) protected benefits.

Code of Federal Regulations, 2013 CFR

2013-04-01

... amendments with the same applicable amendment date are treated as one amendment. Thus, if two amendments have the same applicable amendment date and one amendment, standing alone, increases participants' accrued... are treated as one amendment and will only violate section 411(d)(6) if, for any participant, the net...

Bedding on geotextile mattresses: how much is needed to improve cow comfort?

PubMed

Tucker, C B; Weary, D M

2004-09-01

The objective of our study was to evaluate how the amount of sawdust bedding on mattresses affects dairy cattle behavior and preferences. Eleven nonlactating, multiparous cows were housed individually in pens with access to 3 free stalls. Each stall was fitted with a geotextile mattress covered with either 0, 1, or 7.5 kg of kiln-dried sawdust. The experiment began with 7 d of acclimatization to all 3 stalls. Cows were then allowed access to only 1 of the 3 stalls at a time, each for 3 d (restriction phase). At the end of this restriction phase, cows were allowed free access to all 3 stalls for 3 d (free-choice phase). Time spent lying and the number of lying bouts increased significantly with the amount of bedding, from 12.3 +/- 0.53 h lying and 8.5 +/- 0.62 bouts per 24 h on bare mattresses to 13.8 +/- 0.53 h lying and 10.0 +/- 0.62 bouts per 24 h on mattresses with 7.5 kg of sawdust. In addition, the animals spent less time standing with only the front hooves in the stalls when more sawdust was present. When allowed free access to all 3 options, all 11 animals spent a majority of their time lying and standing in the 7.5-kg option. In conclusion, cows preferred mattresses bedded with 7.5 kg of sawdust, on which they spent more time lying down and less time standing with only the front hooves in stalls. These results indicate that more sawdust bedding improves cow comfort in stalls with geotextile mattresses.

The effect of the X-Stop implantation on intervertebral foramen, segmental spinal canal length and disc space in elderly patients with lumbar spinal stenosis.

PubMed

Wan, Zongmiao; Wang, Shaobai; Kozanek, Michal; Xia, Qun; Mansfield, Frederick L; Lü, Guohua; Wood, Kirkham B; Li, Guoan

2012-03-01

To evaluate the biomechanical effect of the X-Stop device on the intervertebral foramen (IVF) and segmental spinal canal length (SSCL), as well as the intervertebral disc space at the implanted and the adjacent segments in patients with lumbar spinal stenosis (LSS). Eight elderly patients with LSS, scheduled for X-stop implantation, were CT or MRI scanned to construct 3D vertebral models (L2-S1). Before and after the surgery, each patient was also imaged using a dual-fluoroscopic image system during weight-bearing standing and maximum extension-flexion. The positions of the vertebrae were then determined using an established 2D-3D model matching method. The data revealed that the postoperative IVF area was significantly increased by 32.9% (or 32 mm2) (p<0.05) and the IVF width was increased by 24.4% (or 1.1 mm, p=0.06) during extension, but with minimal change in standing and flexion. The IVF heights were significantly (p<0.05) increased at standing by 1.2 mm and extension by 1.8 mm, but not at flexion. The SSCL were significantly (p<0.05) increased at extension by 1.2 mm, but not at standing and flexion. Anterior disc space of the implanted level was significantly decreased from 8.0 to 6.6 mm during standing. The X-Stop implantation efficiently enlarged the IVF area in the elderly patients with LSS at the operated level with little biomechanical effect immediately on the superior and inferior adjacent levels. However, it reduced the anterior disc space at the implanted level.

Time spent in sedentary posture is associated with waist circumference and cardiovascular risk.

PubMed

Tigbe, W W; Granat, M H; Sattar, N; Lean, M E J

2017-05-01

The relationship between metabolic risk and time spent sitting, standing and stepping has not been well established. The present study aimed to determine associations of objectively measured time spent siting, standing and stepping, with coronary heart disease (CHD) risk. A cross-sectional study of healthy non-smoking Glasgow postal workers, n=111 (55 office workers, 5 women, and 56 walking/delivery workers, 10 women), who wore activPAL physical activity monitors for 7 days. Cardiovascular risks were assessed by metabolic syndrome categorisation and 10-year PROCAM (prospective cardiovascular Munster) risk. Mean (s.d.) age was 40 (8) years, body mass index 26.9 (3.9) kg m -2 and waist circumference 95.4 (11.9) cm. Mean (s.d.) high-density lipoprotein cholesterol (HDL cholesterol) 1.33 (0.31), low-density lipoprotein cholesterol 3.11 (0.87), triglycerides 1.23 (0.64) mmol l -1 and 10-year PROCAM risk 1.8 (1.7)%. The participants spent mean (s.d.) 9.1 (1.8) h per day sedentary, 7.6 (1.2) h per day sleeping, 3.9 (1.1) h per day standing and 3.3 (0.9) h per day stepping, accumulating 14 708 (4984) steps per day in 61 (25) sit-to-stand transitions per day. In univariate regressions-adjusting for age, sex, family history of CHD, shift worked, job type and socioeconomic status-waist circumference (P=0.005), fasting triglycerides (P=0.002), HDL cholesterol (P=0.001) and PROCAM risk (P=0.047) were detrimentally associated with sedentary time. These associations remained significant after further adjustment for sleep, standing and stepping in stepwise regression models. However, after further adjustment for waist circumference, the associations were not significant. Compared with those without the metabolic syndrome, participants with the metabolic syndrome were significantly less active-fewer steps, shorter stepping duration and longer time sitting. Those with no metabolic syndrome features walked >15 000 steps per day or spent >7 h per day upright. Longer time spent in sedentary posture is significantly associated with higher CHD risk and larger waist circumference.

Clearcut harvesting costs and production rates for young-growth mixed-conifer stands

Treesearch

William A. Atkinson; Dale O. Hall

1966-01-01

In clearcutting 90-year-old stands at the Challenge Experimental Forest, all merchantable trees greater than 12 inches d.b.h. were removed. Felling costs averaged $3.86 and required 0.55 man-hours per M bd. ft. in cut volumes averaging 19,700 bd. ft. per acre. Yarding, at a rate of 0.54 hours per M bd. ft., cost $4.42.

3D graphene nanomaterials for binder-free supercapacitors: scientific design for enhanced performance.

PubMed

He, Shuijian; Chen, Wei

2015-04-28

Because of the excellent intrinsic properties, especially the strong mechanical strength, extraordinarily high surface area and extremely high conductivity, graphene is deemed as a versatile building block for fabricating functional materials for energy production and storage applications. In this article, the recent progress in the assembly of binder-free and self-standing graphene-based materials, as well as their application in supercapacitors are reviewed, including electrical double layer capacitors, pseudocapacitors, and asymmetric supercapacitors. Various fabrication strategies and the influence of structures on the capacitance performance of 3D graphene-based materials are discussed. We finally give concluding remarks and an outlook on the scientific design of binder-free and self-standing graphene materials for achieving better capacitance performance.

3D graphene nanomaterials for binder-free supercapacitors: scientific design for enhanced performance

NASA Astrophysics Data System (ADS)

He, Shuijian; Chen, Wei

2015-04-01

Because of the excellent intrinsic properties, especially the strong mechanical strength, extraordinarily high surface area and extremely high conductivity, graphene is deemed as a versatile building block for fabricating functional materials for energy production and storage applications. In this article, the recent progress in the assembly of binder-free and self-standing graphene-based materials, as well as their application in supercapacitors are reviewed, including electrical double layer capacitors, pseudocapacitors, and asymmetric supercapacitors. Various fabrication strategies and the influence of structures on the capacitance performance of 3D graphene-based materials are discussed. We finally give concluding remarks and an outlook on the scientific design of binder-free and self-standing graphene materials for achieving better capacitance performance.

2. View looking southeast at north and west facades of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. View looking southeast at north and west facades of Test Stand 'D' workshop 4222/E-23, with Test Stand 'D' tower in background and tunnel access shed to the right. Equipment on 4222/E-23 roof is for air conditioning. - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Workshop, Edwards Air Force Base, Boron, Kern County, CA

1. View looking northeast at the west and south facades ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. View looking northeast at the west and south facades of Test Stand 'D' workshop 4222/E-23. Test Stand 'D' tower nitrogen tanks, television camera platform and access stairs are at right of image. Ductwork atop roof is for air conditioning system. - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Workshop, Edwards Air Force Base, Boron, Kern County, CA

Credit BG. View looking west down into Test Stand "D" ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. View looking west down into Test Stand "D" vertical vacuum cell with top removed. Access to cell is normally through large round port seen in view. Piping and cradling toward bottom of cell was last used in tests of Viking space probe engines - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Simulating Carbon cycle and phenology in complex forests using a multi-layer process based ecosystem model; evaluation and use of 3D-CMCC-Forest Ecosystem Model in a deciduous and an evergreen neighboring forests, within the area of Brasschaat (Be)

NASA Astrophysics Data System (ADS)

Marconi, S.; Collalti, A.; Santini, M.; Valentini, R.

2013-12-01

3D-CMCC-Forest Ecosystem Model is a process based model formerly developed for complex forest ecosystems to estimate growth, water and carbon cycles, phenology and competition processes on a daily/monthly time scale. The Model integrates some characteristics of the functional-structural tree models with the robustness of the light use efficiency approach. It treats different heights, ages and species as discrete classes, in competition for light (vertical structure) and space (horizontal structure). The present work evaluates the results of the recently developed daily version of 3D-CMCC-FEM for two neighboring different even aged and mono specific study cases. The former is a heterogeneous Pedunculate oak forest (Quercus robur L. ), the latter a more homogeneous Scot pine forest (Pinus sylvestris L.). The multi-layer approach has been evaluated against a series of simplified versions to determine whether the improved model complexity in canopy structure definition increases its predictive ability. Results show that a more complex structure (three height layers) should be preferable to simulate heterogeneous scenarios (Pedunculate oak stand), where heights distribution within the canopy justify the distinction in dominant, dominated and sub-dominated layers. On the contrary, it seems that using a multi-layer approach for more homogeneous stands (Scot pine stand) may be disadvantageous. Forcing the structure of an homogeneous stand to a multi-layer approach may in fact increase sources of uncertainty. On the other hand forcing complex forests to a mono layer simplified model, may cause an increase in mortality and a reduction in average DBH and Height. Compared with measured CO2 flux data, model results show good ability in estimating carbon sequestration trends, on both a monthly/seasonal and daily time scales. Moreover the model simulates quite well leaf phenology and the combined effects of the two different forest stands on CO2 fluxes.

Effect of In-Flight Exercise and Extravehicular Activity on Postflight Stand Tests

NASA Technical Reports Server (NTRS)

Lee, Stuart M. C.; Moore, Alan D., Jr.; Fritsch-Yelle, Janice; Greenisen, Michael; Schneider, Suzanne M.; Foster, Philip P.

2000-01-01

The purpose of this study was to determine whether exercise performed by Space Shuttle crewmembers during short-duration spaceflights (9-16 days) affects the heart rate (HR) and blood pressure (BP) responses to standing within 2-4 hr of landing. Thirty crewmembers performed self-selected in-flight exercise and maintained exercise logs to monitor their exercise intensity and duration. A 10min stand test, preceded by at least 6 min of quiet supine rest, was completed 10- 15 d before launch (PRE) and within four hours of landing (POST). Based upon their in-flight exercise records, subjects were grouped as either high (HIex: = 3x/week, HR = 70% ,HRMax, = 20 min/session, n = 11), medium (MEDex: = 3x/week, HR = 70% HRmax, = 20 min/session, n = 10), or low (LOex: = 3x/week, HR and duration variable, n = 11) exercisers. HR and BP responses to standing were compared between groups (ANOVA, or analysis of variance, P < 0.05). There were no PRE differences between the groups in supine or standing HR and BP. Although POST supine HR was similar to PRE, all groups had an increased standing HR compared to PRE. The increase in HR upon standing was significantly greater after flight in the LOex group (36+/-5 bpm) compared to HIex or MEDex groups (25+/-1bpm; 22+/-2 bpm). Similarly, the decrease in pulse pressure (PP) from supine to standing was unchanged after spaceflight in the MEDex and HIex groups, but was significantly less in the LOex group (PRE: -9+/- 3, POST: -19+/- 4 mmHg). Thus, moderate to high levels of in-flight exercise attenuated HR and PP responses to standing after spaceflight compared.

A Stand-Alone Synbiotic Treatment for the Prevention of D-Lactic Acidosis in Short Bowel Syndrome

PubMed Central

Takahashi, Kazuhiro; Terashima, Hideo; Kohno, Keisuke; Ohkohchi, Nobuhiro

2013-01-01

Synbiotics are combinations of probiotics and prebiotics that have recently been used in the context of various gastrointestinal diseases, including infectious enteritis, inflammatory bowel disease, and bowel obstruction. We encountered a patient with recurrent D-lactic acidosis who was treated successfully for long periods using synbiotics. The patient was diagnosed as having short bowel syndrome and had recurrent episodes of neurologic dysfunction due to D-lactic acidosis. In addition to fasting, the patient had been treated with antibiotics to eliminate D-lactate–producing bacteria. After the failure of antibiotic treatment, a stand-alone synbiotic treatment was started, specifically Bifidobacterium breve Yakult and Lactobacillus casei Shirota as probiotics, and galacto-oligosaccharide as a prebiotic. Serum D-lactate levels declined, and the patient has been recurrence-free for 3 years without dietary restriction. Synbiotics allowed the reduction in colonic absorption of D-lactate by both prevention of D-lactate–producing bacterial overgrowth and stimulation of intestinal motility, leading to remission of D-lactate acidosis. PMID:23701144

Patterning and manipulating microparticles into a three-dimensional matrix using standing surface acoustic waves

NASA Astrophysics Data System (ADS)

Nguyen, T. D.; Tran, V. T.; Fu, Y. Q.; Du, H.

2018-05-01

A method based on standing surface acoustic waves (SSAWs) is proposed to pattern and manipulate microparticles into a three-dimensional (3D) matrix inside a microchamber. An optical prism is used to observe the 3D alignment and patterning of the microparticles in the vertical and horizontal planes simultaneously. The acoustic radiation force effectively patterns the microparticles into lines of 3D space or crystal-lattice-like matrix patterns. A microparticle can be positioned precisely at a specified vertical location by balancing the forces of acoustic radiation, drag, buoyancy, and gravity acting on the microparticle. Experiments and finite-element numerical simulations both show that the acoustic radiation force increases gradually from the bottom of the chamber to the top, and microparticles can be moved up or down simply by adjusting the applied SSAW power. Our method has great potential for acoustofluidic applications, building the large-scale structures associated with biological objects and artificial neuron networks.

Three-dimensional continuous particle focusing in a microfluidic channel via standing surface acoustic waves (SSAW).

PubMed

Shi, Jinjie; Yazdi, Shahrzad; Lin, Sz-Chin Steven; Ding, Xiaoyun; Chiang, I-Kao; Sharp, Kendra; Huang, Tony Jun

2011-07-21

Three-dimensional (3D) continuous microparticle focusing has been achieved in a single-layer polydimethylsiloxane (PDMS) microfluidic channel using a standing surface acoustic wave (SSAW). The SSAW was generated by the interference of two identical surface acoustic waves (SAWs) created by two parallel interdigital transducers (IDTs) on a piezoelectric substrate with a microchannel precisely bonded between them. To understand the working principle of the SSAW-based 3D focusing and investigate the position of the focal point, we computed longitudinal waves, generated by the SAWs and radiated into the fluid media from opposite sides of the microchannel, and the resultant pressure and velocity fields due to the interference and reflection of the longitudinal waves. Simulation results predict the existence of a focusing point which is in good agreement with our experimental observations. Compared with other 3D focusing techniques, this method is non-invasive, robust, energy-efficient, easy to implement, and applicable to nearly all types of microparticles.

Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite nanowalls for supercapacitors with high specific capacitances

NASA Astrophysics Data System (ADS)

Xiao, Yuanhua; Zhang, Aiqin; Liu, Shaojun; Zhao, Jihong; Fang, Shaoming; Jia, Dianzeng; Li, Feng

2012-12-01

Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite (Co3O4) nanowalls have been successfully synthesized in large scale by calcining three dimensional (3D) hierarchical nanostructures consisting of single crystalline cobalt carbonate hydroxide hydrate - Co(CO3)0.5(OH)·0.11H2O nanowalls prepared with a solvothermal method. The step-by-step decomposition of the precursor can generate porous Co3O4 nanowalls with BET surface area of 88.34 m2 g-1. The as-prepared Co3O4 nanoarchitectures show superior specific capacitance to the most Co3O4 supercapacitor electrode materials to date. After continuously cycled for 1000 times of charge-discharge at 4 A g-1, the supercapacitors can retain ca 92.3% of their original specific capacitances. The excellent performances of the devices can be attributed to the porous and hierarchical 3D nanostructure of the materials.

Credit WCT. Photographic copy of photograph, view of Test Stand ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view of Test Stand "D" from Test Stand "A" while a rocket engine test is in progress. Cloud of steam is from partly from water created by propellant reaction and from water sprayed by flame bucket into engine exhaust for cooling purposes. A portion of Test Stand "C" is visible at the far right. (JPL negative no. 384-2082-B, 23 October 1959) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

3. SOUTH FLAME DEFLECTOR FROM THE REINFORCED CONCRETE ROOF, VIEW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. SOUTH FLAME DEFLECTOR FROM THE REINFORCED CONCRETE ROOF, VIEW TOWARDS EAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-2, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Credit WCT. Photographic copy of photograph, view looking south down ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view looking south down easternmost tunnel axis during second phase of JPL tunnel construction in 1959. Reinforced concrete formwork for Test Stand "D" foundation appears in left foreground. Formwork for Building 4222/E-23 (Test Stand "D" Workshop) is in place in right foreground with disturbed earth for western leg of tunnel system evident in background. Test Stand "C" is in center background, where first phase of tunnel construction ended. Test Stand "A" appears as tower in right background. (JPL negative no. 384-1838-C, 9 March 1959) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Ethylene production throughout growth and development of plants

NASA Technical Reports Server (NTRS)

Wheeler, Raymond M.; Peterson, Barbara V.; Stutte, Gary W.

2004-01-01

Ethylene production by 10 or 20 m2 stands of wheat, soybean, lettuce, potato, and tomato was monitored throughout growth and development in an atmospherically closed plant chamber. Chamber ethylene levels varied among species and rose during periods of canopy expansion and rapid growth for all species. Following this, ethylene levels either declined during seed fill and maturation for wheat and soybean, or remained relatively constant for potato and tomato (during flowering and early fruit development). Lettuce plants were harvested during rapid growth and peak ethylene production. Chamber ethylene levels increased rapidly during tomato ripening, reaching concentrations about 10 times that measured during vegetative growth. The highest ethylene production rates during vegetative growth ranged from 1.6 to 2.5 nmol m-2 d-1 during rapid growth of lettuce and wheat stands, or about 0.3 to 0.5 nmol g-1 fresh weight per hour. Estimates of stand ethylene production during tomato ripening showed that rates reached 43 nmol m-2 d-1 in one study and 93 nmol m-2 d-1 in a second study with higher lighting, or about 50x that of the rate during vegetative growth of tomato. In a related test with potato, the photoperiod was extended from 12 to 24 hours (continuous light) at 58 days after planting (to increase tuber yield), but this change in the environment caused a sharp increase in ethylene production from the basal rate of 0.4 to 6.2 nmol m-2 d-1. Following this, the photoperiod was changed back to 12 h at 61 days and ethylene levels decreased. The results suggest three separate categories of ethylene production were observed with whole stands of plants: 1) production during rapid vegetative growth, 2) production during climacteric fruit ripening, and 3) production from environmental stress.

Calibration of d.b.h.-height equations for southern hardwoods

Treesearch

Thomas B. Lynch; A. Gordon Holley; Douglas J. Stevenson

2006-01-01

Data from southern hardwood stands in East Texas were used to estimate parameters for d.b.h.-height equations. Mixed model estimation methods were used, so that the stand from which a tree was sampled was considered a random effect. This makes it possible to calibrate these equations using data collected in a local stand of interest, by using d.b.h. and total height...

Stress wave propagation on standing trees. Part 2, Formation of 3D stress wave contour maps.

Treesearch

Juan Su; Houjiang Zhang; Xiping Wang

2009-01-01

Nondestructive evaluation (NDE) of wood quality in standing trees is an important procedure in the forest operational value chain worldwide. The goal of this paper is to investigate how a stress wave travel in a tree stem as it is introduced into the tree through a mechanical impact. Experimental stress wave data was obtained on freshly cut red pine logs in the...

Experimental 3-D SAR Human Target Signature Analysis

DTIC Science & Technology

2014-07-21

is a fairly transparent one constructed of drywall made of wood studs, gypsum, insulating material, and vinyl coating on the exterior. A LIDAR image...transparent wall such as drywall , there is a significant increase in the amount of clutter and multipath. Figure 8. LIDAR imagery of a human...standing inside a building constructed of drywall made of wood stud, gypsum, insulating material, and vinyl coating. In the human standing images

High-immersion three-dimensional display of the numerical computer model

NASA Astrophysics Data System (ADS)

Xing, Shujun; Yu, Xunbo; Zhao, Tianqi; Cai, Yuanfa; Chen, Duo; Chen, Zhidong; Sang, Xinzhu

2013-08-01

High-immersion three-dimensional (3D) displays making them valuable tools for many applications, such as designing and constructing desired building houses, industrial architecture design, aeronautics, scientific research, entertainment, media advertisement, military areas and so on. However, most technologies provide 3D display in the front of screens which are in parallel with the walls, and the sense of immersion is decreased. To get the right multi-view stereo ground image, cameras' photosensitive surface should be parallax to the public focus plane and the cameras' optical axes should be offset to the center of public focus plane both atvertical direction and horizontal direction. It is very common to use virtual cameras, which is an ideal pinhole camera to display 3D model in computer system. We can use virtual cameras to simulate the shooting method of multi-view ground based stereo image. Here, two virtual shooting methods for ground based high-immersion 3D display are presented. The position of virtual camera is determined by the people's eye position in the real world. When the observer stand in the circumcircle of 3D ground display, offset perspective projection virtual cameras is used. If the observer stands out the circumcircle of 3D ground display, offset perspective projection virtual cameras and the orthogonal projection virtual cameras are adopted. In this paper, we mainly discussed the parameter setting of virtual cameras. The Near Clip Plane parameter setting is the main point in the first method, while the rotation angle of virtual cameras is the main point in the second method. In order to validate the results, we use the D3D and OpenGL to render scenes of different viewpoints and generate a stereoscopic image. A realistic visualization system for 3D models is constructed and demonstrated for viewing horizontally, which provides high-immersion 3D visualization. The displayed 3D scenes are compared with the real objects in the real world.

3. FLAME DEFLECTOR AT CENTER, CONNECTING TUNNEL AT CENTER RIGHT, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. FLAME DEFLECTOR AT CENTER, CONNECTING TUNNEL AT CENTER RIGHT, VIEW TOWARDS SOUTHWEST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-1, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Vitamin D deficiency is associated with orthostatic hypotension in oldest-old women.

PubMed

Annweiler, C; Schott, A-M; Rolland, Y; Beauchet, O

2014-09-01

Orthostatic hypotension, a condition that mostly affects 'oldest-old' (i.e. ≥80 years) adults, is primarily explained by age-related dysfunction of blood pressure control. Vitamin D may contribute to blood pressure control. The aim of this study was to determine whether vitamin D deficiency is associated with orthostatic hypotension in oldest-old adults. Cross-sectional analysis at baseline of the EPIDOS study. Five French areas. A total of 329 community-dwelling oldest-old women (mean age 83.3 ± 0.2 years). Orthostatic hypotension was defined as a systolic blood pressure drop of ≥20 mmHg and/or a diastolic blood pressure drop of ≥10 mmHg within 3 min of standing. Vitamin D deficiency was defined as a serum 25-hydroxyvitamin D (25OHD) concentration ≤10 ng mL(-1) . Covariates included in the models were age, body mass index, diabetes mellitus, supine mean arterial pressure, number of drugs taken per day, use of antihypertensive or psychoactive drugs, cognition, quadriceps strength, current smoking, alcohol consumption, serum concentrations of parathyroid hormone, calcium and creatinine and season of testing. Diastolic orthostatic hypotension was observed more often among women with vitamin D deficiency (19.2%) compared to those without (10.0%; P = 0.03). There was an inverse linear association between 25OHD concentration and change in diastolic blood pressure after 3 min of standing (adjusted β = -0.07, P = 0.046). Similarly, 25OHD deficiency was associated with orthostatic hypotension [adjusted odds ratio (OR) 3.36, P = 0.004], specifically with diastolic orthostatic hypotension (adjusted OR 3.81, P = 0.003). 25OHD deficiency was associated with orthostatic hypotension in oldest-old women, due to a greater drop in diastolic blood pressure on standing. This finding may lead to better understanding of the pathophysiology of falls in oldest-old adults with vitamin D deficiency. © 2014 The Association for the Publication of the Journal of Internal Medicine.

Lineshape-asymmetry elimination in weak atomic transitions driven by an intense standing wave field

NASA Astrophysics Data System (ADS)

Antypas, Dionysios; Fabricant, Anne; Budker, Dmitry

2018-05-01

Owing to the ac-Stark effect, the lineshape of a weak optical transition in an atomic beam can become significantly distorted, when driven by an intense standing wave field. We use an Yb atomic beam to study the lineshape of the 6s2 1S0 -> 5d6s 3D1 transition, which is excited with light circulating in a Fabry-Perot resonator. We demonstrate two methods to avoid the distortion of the transition profile. Of these, one relies on the operation of the resonator in multiple longitudinal modes, and the other in multiple transverse modes.

Efficient three-dimensional resist profile-driven source mask optimization optical proximity correction based on Abbe-principal component analysis and Sylvester equation

NASA Astrophysics Data System (ADS)

Lin, Pei-Chun; Yu, Chun-Chang; Chen, Charlie Chung-Ping

2015-01-01

As one of the critical stages of a very large scale integration fabrication process, postexposure bake (PEB) plays a crucial role in determining the final three-dimensional (3-D) profiles and lessening the standing wave effects. However, the full 3-D chemically amplified resist simulation is not widely adopted during the postlayout optimization due to the long run-time and huge memory usage. An efficient simulation method is proposed to simulate the PEB while considering standing wave effects and resolution enhancement techniques, such as source mask optimization and subresolution assist features based on the Sylvester equation and Abbe-principal component analysis method. Simulation results show that our algorithm is 20× faster than the conventional Gaussian convolution method.

NEUTRINO-DRIVEN TURBULENT CONVECTION AND STANDING ACCRETION SHOCK INSTABILITY IN THREE-DIMENSIONAL CORE-COLLAPSE SUPERNOVAE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdikamalov, Ernazar; Ott, Christian D.; Radice, David

2015-07-20

We conduct a series of numerical experiments into the nature of three-dimensional (3D) hydrodynamics in the postbounce stalled-shock phase of core-collapse supernovae using 3D general-relativistic hydrodynamic simulations of a 27 M{sub ⊙} progenitor star with a neutrino leakage/heating scheme. We vary the strength of neutrino heating and find three cases of 3D dynamics: (1) neutrino-driven convection, (2) initially neutrino-driven convection and subsequent development of the standing accretion shock instability (SASI), and (3) SASI-dominated evolution. This confirms previous 3D results of Hanke et al. and Couch and Connor. We carry out simulations with resolutions differing by up to a factor ofmore » ∼4 and demonstrate that low resolution is artificially favorable for explosion in the 3D convection-dominated case since it decreases the efficiency of energy transport to small scales. Low resolution results in higher radial convective fluxes of energy and enthalpy, more fully buoyant mass, and stronger neutrino heating. In the SASI-dominated case, lower resolution damps SASI oscillations. In the convection-dominated case, a quasi-stationary angular kinetic energy spectrum E(ℓ) develops in the heating layer. Like other 3D studies, we find E(ℓ) ∝ℓ{sup −1} in the “inertial range,” while theory and local simulations argue for E(ℓ) ∝ ℓ{sup −5/3}. We argue that current 3D simulations do not resolve the inertial range of turbulence and are affected by numerical viscosity up to the energy-containing scale, creating a “bottleneck” that prevents an efficient turbulent cascade.« less

a Method for the Registration of Hemispherical Photographs and Tls Intensity Images

NASA Astrophysics Data System (ADS)

Schmidt, A.; Schilling, A.; Maas, H.-G.

2012-07-01

Terrestrial laser scanners generate dense and accurate 3D point clouds with minimal effort, which represent the geometry of real objects, while image data contains texture information of object surfaces. Based on the complementary characteristics of both data sets, a combination is very appealing for many applications, including forest-related tasks. In the scope of our research project, independent data sets of a plain birch stand have been taken by a full-spherical laser scanner and a hemispherical digital camera. Previously, both kinds of data sets have been considered separately: Individual trees were successfully extracted from large 3D point clouds, and so-called forest inventory parameters could be determined. Additionally, a simplified tree topology representation was retrieved. From hemispherical images, leaf area index (LAI) values, as a very relevant parameter for describing a stand, have been computed. The objective of our approach is to merge a 3D point cloud with image data in a way that RGB values are assigned to each 3D point. So far, segmentation and classification of TLS point clouds in forestry applications was mainly based on geometrical aspects of the data set. However, a 3D point cloud with colour information provides valuable cues exceeding simple statistical evaluation of geometrical object features and thus may facilitate the analysis of the scan data significantly.

Biomechanics of compensatory mechanisms in spinal-pelvic complex

NASA Astrophysics Data System (ADS)

Ivanov, D. V.; Hominets, V. V.; Kirillova, I. V.; Kossovich, L. Yu; Kudyashev, A. L.; Teremshonok, A. V.

2018-04-01

3D geometric solid computer model of spinal-pelvic complex was constructed on the basis of computed tomography and full body X-ray in standing position data. The constructed model was used for biomechanical analysis of compensatory mechanisms arising in the spine with anteversion and retroversion of the pelvis. The results of numerical biomechanical 3D modeling are in good agreement with the clinical data.

Looking northeast from Test Stand 'A' superstructure towards Test Stand ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking northeast from Test Stand 'A' superstructure towards Test Stand 'D' tower (4223/E-24, left background), Test Stand 'C' tower (4217/E-18, center), and Test Stand 'B' (4215/E-16, right foreground). - Jet Propulsion Laboratory Edwards Facility, Edwards Air Force Base, Boron, Kern County, CA

3. FLAME DEFLECTOR AT UPPER LEFT, FERROCEMENT APRON CONTROLS AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. FLAME DEFLECTOR AT UPPER LEFT, FERROCEMENT APRON CONTROLS AT LOWER RIGHT, VIEW TOWARDS NORTHEAST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-4, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Local 3d Electronic Structures of Co-Based Complexes with Medicinal Molecules Probed by Soft X-ray Absorption

NASA Astrophysics Data System (ADS)

Yamagami, Kohei; Fujiwara, Hidenori; Imada, Shin; Kadono, Toshiharu; Yamanaka, Keisuke; Muro, Takayuki; Tanaka, Arata; Itai, Takuma; Yoshinari, Nobuto; Konno, Takumi; Sekiyama, Akira

2017-07-01

We have examined the local 3d electronic structures of Co-Au multinuclear complexes with the medicinal molecules d-penicillaminate (d-pen) [Co{Au(PPh3)(d-pen)}2]ClO4 and [Co3{Au3(tdme)(d-pen)3}2] by Co L2,3-edge soft X-ray absorption (XAS) spectroscopy, where PPh3 denotes triphenylphosphine and tdme stands for 1,1,1-tris[(diphenylphosphino)methyl]ethane. The Co L2,3-edge XAS spectra indicate the localized ionic 3d electronic states in both materials. The experimental spectra are well explained by spectral simulation for a localized Co ion under ligand fields with the full multiplet theory, which verifies that the ions are in the low-spin Co3+ state in the former compound and in the high-spin Co2+ state in the latter.

Microzooplankton grazing and phytoplankton growth in marine mesocosms with increased CO2 levels

NASA Astrophysics Data System (ADS)

Suffrian, K.; Simonelli, P.; Nejstgaard, J. C.; Putzeys, S.; Carotenuto, Y.; Antia, A. N.

2008-08-01

Microzooplankton grazing and algae growth responses to increasing pCO2 levels (350, 700 and 1050 μatm) were investigated in nitrate and phosphate fertilized mesocosms during the PeECE III experiment 2005. Grazing and growth rates were estimated by the dilution technique combined with taxon specific HPLC pigment analysis. Microzooplankton composition was determined by light microscopy. Despite a range of up to 3 times the present CO2 levels, there were no clear differences in any measured parameter between the different CO2 treatments. During days 3 9 of the experiment the algae community standing stock, measured as chlorophyll a (Chl-a), showed the highest instantaneous grow rates (k=0.37 0.99 d-1) and increased from ca. 2 3 to 6 12 μg l-1, in all mesocosms. Afterwards the phytoplankton standing stock decreased in all mesocosms until the end of the experiment. The microzooplankton standing stock, that was mainly constituted by dinoflagellates and ciliates, varied between 23 and 130 μg C l-1 (corresponding to 1.9 and 10.8 μmol C l-1), peaking on day 13 15, apparently responding to the phytoplankton development. Instantaneous Chl-a growth rates were generally higher than the grazing rates, indicating only a limited overall effect of microzooplankton grazing on the most dominant phytoplankton. Diatoms and prymnesiophytes were significantly grazed (12 43% of the standing stock d-1) only in the pre-bloom phase when they were in low numbers, and in the post-bloom phase when they were already affected by low nutrients and/or viral lysis. The cyanobacteria populations appeared more affected by microzooplankton grazing which generally removed 20 65% of the standing stock per day.

Credit BG. West elevation of Test Stand "D" tower, with ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. West elevation of Test Stand "D" tower, with workshop on left, and tunnel entrance at right. Tower is accessed by exterior steel stairway; the vertical vacuum cell (Dv Cell) is obscured behind large square sunscreen. Below the sunscreen can be seen the end of the horizontal vacuum duct leading from the vacuum cell - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Fast time variations of supernova neutrino signals from 3-dimensional models

DOE PAGES

Lund, Tina; Wongwathanarat, Annop; Janka, Hans -Thomas; ...

2012-11-19

Here, we study supernova neutrino flux variations in the IceCube detector, using 3D models based on a simplified neutrino transport scheme. The hemispherically integrated neutrino emission shows significantly smaller variations compared with our previous study of 2D models, largely because of the reduced activity of the standing accretion shock instability in this set of 3D models which we interpret as a pessimistic extreme. For the studied cases, intrinsic flux variations up to about 100 Hz frequencies could still be detected in a supernova closer than about 2 kpc.

Early impacts of biological control on canopy cover and water use of the invasive saltcedar tree (Tamarix spp.) in western Nevada, USA

USGS Publications Warehouse

Pattison, R.R.; D'Antonio, C. M.; Dudley, T.L.; Allander, K.K.; Rice, B.

2011-01-01

The success of biological control programs is rarely assessed beyond population level impacts on the target organism. The question of whether a biological control agent can either partially or completely restore ecosystem services independent of population level control is therefore still open to discussion. Using observational and experimental approaches, we investigated the ability of the saltcedar leaf beetle [Diorhabda carinulata (Brull??) (Coleoptera: Chrysomelidae)] to reduce the water use of saltcedar trees (Tamarix ramosissima Ledeb.) in two sites (Humboldt and Walker Rivers) in Nevada, USA. At these sites D. carinulata defoliated the majority of trees within 25 and 9 km, respectively, of the release location within 3 years. At the Humboldt site, D. carinulata reduced the canopy cover of trees adjacent to the release location by >90%. At a location 4 km away during the first year of defoliation, D. carinulata reduced peak (August) stem water use by 50-70% and stand transpiration (July to late September) by 75% (P = 0. 052). There was, however, no reduction in stem water use and stand transpiration during the second year of defoliation due to reduced beetle abundances at that location. At the Walker site, we measured stand evapotranspiration (ET) in the center of a large saltcedar stand and found that ET was highest immediately prior to D. carinulata arrival, dropped dramatically with defoliation, and remained low through the subsequent 2 years of the study. In contrast, near the perimeter of the stand, D. carinulata did not reduce sap flow, partly because of low rates of defoliation but also because of increased water use per unit leaf area in response to defoliation. Taken together, our results provide evidence that in the early stages of population expansion D. carinulata can lead to substantial declines in saltcedar water use. The extent of these declines varies spatially and temporally and is dependent on saltcedar compensatory responses along with D. carinulata population dynamics and patterns of dispersal. ?? 2010 Springer-Verlag (outside the USA).

Effects of short-term repeated exposure to different flooring surfaces on the behavior and physiology of dairy cattle.

PubMed

Schütz, K E; Cox, N R

2014-05-01

Dairy cattle managed in some pasture-based systems such as in New Zealand are predominantly kept outdoors all year around, but are often taken off pasture for periods of time in wet weather to avoid soil damage. It is common to keep cattle on concrete surfaces during such "stand-off" practices and we investigated whether the addition of rubber matting onto concrete areas improves the welfare of dairy cattle. Sixteen groups of 5 cows (4 groups/treatment, 5 cows/group) were allocated to 1 of 4 treatments (concrete, 12-mm-thick rubber mat, 24-mm-thick rubber mat, or deep-bedded wood chips) and kept on these surfaces for 18 h/24h for 4 consecutive days (6h on pasture/24h). Each 4-d stand-off period was repeated 4 times (with 7 d of recovery between periods) to study the accumulated effects of repeated stand-off. Lying behavior was recorded continuously during the experiment. Gait score, stride length, hygiene score, live weight, and blood samples for cortisol analysis were recorded immediately before and after each stand-off period. Cows on wood chips spent the most time lying, and cows on concrete spent the least time lying compared with those on other surfaces [wood chips: 10.8h, 24-mm rubber mat: 7.3h, 12-mm rubber mat: 6.0 h, and concrete: 2.8h/18 h, standard error of the difference (SED): 0.71 h]. Cows on concrete spent more time lying during the 6h on pasture, likely compensating for the reduced lying during the stand-off period. Similarly, cows on concrete spent more time lying on pasture between stand-off periods (concrete: 12.1h, 12-mm rubber mat: 11.1h, 24-mm rubber mat: 11.2h, and wood chips: 10.7h/24h, SED: 0.28 h). Cows on concrete had higher gait score and shorter stride length after the 4-d stand-off period compared with cows on the other surface types, suggesting a change in gait pattern caused by discomfort. Cows on rubber mats were almost 3 times dirtier than cows on concrete or wood chips. Cortisol and live weight decreased for all treatment groups during the stand-off period. We observed no major effect of the repeated stand-off exposure. In summary, adding rubber matting onto concrete surfaces for stand-off purposes is beneficial for animal welfare. A well-managed wood chip surface offered the best welfare for dairy cows removed from pasture, and the findings of this study confirm that a concrete surface decreases the welfare of cows removed from pasture. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Plasmonic Hotspots in Air: An Omnidirectional Three-Dimensional Platform for Stand-Off In-Air SERS Sensing of Airborne Species.

PubMed

Phan-Quang, Gia Chuong; Lee, Hiang Kwee; Teng, Hao Wen; Koh, Charlynn Sher Lin; Yim, Barnabas Qinwei; Tan, Eddie Khay Ming; Tok, Wee Lee; Phang, In Yee; Ling, Xing Yi

2018-05-14

Molecular-level airborne sensing is critical for early prevention of disasters, diseases, and terrorism. Currently, most 2D surface-enhanced Raman spectroscopy (SERS) substrates used for air sensing have only one functional surface and exhibit poor SERS-active depth. "Aerosolized plasmonic colloidosomes" (APCs) are introduced as airborne plasmonic hotspots for direct in-air SERS measurements. APCs function as a macroscale 3D and omnidirectional plasmonic cloud that receives laser irradiation and emits signals in all directions. Importantly, it brings about an effective plasmonic hotspot in a length scale of approximately 2.3 cm, which affords 100-fold higher tolerance to laser misalignment along the z-axis compared with 2D SERS substrates. APCs exhibit an extraordinary omnidirectional property and demonstrate consistent SERS performance that is independent of the laser and analyte introductory pathway. Furthermore, the first in-air SERS detection is demonstrated in stand-off conditions at a distance of 200 cm, highlighting the applicability of 3D omnidirectional plasmonic clouds for remote airborne sensing in threatening or inaccessible areas. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

In utero exposure to heat stress during late gestation has prolonged effects on the activity patterns and growth of dairy calves.

PubMed

Laporta, J; Fabris, T F; Skibiel, A L; Powell, J L; Hayen, M J; Horvath, K; Miller-Cushon, E K; Dahl, G E

2017-04-01

Exposure to heat stress during late gestation exerts negative carryover effects on the postnatal performance of the calf. In this study, we evaluated the health, growth, and activity patterns of calves born to cows exposed to heat stress (HT, provided only shade, n = 31) or cooling (CL, fans, soakers, and shade, n = 29) during late gestation (∼46 d, maternal dry period). Calves' body weight, rectal temperature, suckling reflex, and movement scores were recorded at birth, and calves were fed 6.6 L of maternal colostrum in 2 meals. Blood samples were collected at birth (before feeding), 24 h after birth, and at d 10 and 28 of age. Calves were housed in individual pens, fed pasteurized milk (6 L/d), and had ad libitum access to grain and water until weaning (49 d). Activity was assessed during the first week of life (wk 1), at weaning (wk 7), and in the first week postweaning (wk 8) using electronic data loggers. Health and body weight were monitored weekly. At birth, calves born to CL cows were heavier (41.9 vs. 39.1 ± 0.8 kg), their temperature was lower (38.9 vs. 39.3 ± 0.08°C), and they were more efficient at absorbing IgG than HT calves. Suckling reflex and movement score at birth were not different between groups, but calves born to CL cows spent more time (50 min/d) standing in the first week of life as a result of longer standing bouts. In wk 7 and 8, calves born to CL cows had less frequent standing bouts than HT heifers, but CL heifers maintained greater total daily standing time (36 min/d) due to longer (7 min/bout) standing bouts. All calves were healthy, but HT heifers tended to have higher (looser) fecal scores on d 10. Heifers born from CL cows gained 0.2 kg/d more from birth to weaning, weighed 4 kg more at weaning, and had greater concentrations of IGF-1 than HT calves, particularly on d 28. In utero heat stress during late gestation had immediate and prolonged effects on passive immunity, growth, and activity patterns in dairy calves. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Prediction of parturition in Holstein dairy cattle using electronic data loggers.

PubMed

Titler, M; Maquivar, M G; Bas, S; Rajala-Schultz, P J; Gordon, E; McCullough, K; Federico, P; Schuenemann, G M

2015-08-01

The objective of the present study was to assess the effect of parturition on behavioral activity [steps, standing time, lying time, lying bouts (LB), and duration of LB] 4 d before calving using electronic data loggers. Animals (n=132) from 3 herds were housed in similar freestall barns using a prepartum pen 21 d before the expected calving date and were moved into a contiguous individual maternity pen for parturition. Electronic data loggers were placed on a hind leg of prepartum heifers (heifers, n=33) and cows (cows, n=99) at 7±3 d before the expected calving date and removed at 14±3 d in milk. Calving ease (scale 1-4), parity, calving date and time, and stillbirth (born dead or died within 24h) were recorded. The number of steps (no./d), standing time (min/d), lying time (min/d), number of LB (no./d), and duration of LB (min/b) were recorded. Data were analyzed using MIXED procedures of SAS, adjusting for the herd effect. Only cows experiencing unassisted births (calving ease=1) were included in the study. An activity index was developed to predict calving time. Heifers and cows with unassisted births had significantly higher number of steps and longer standing time, decreased lying time, and more LB of shorter duration 24h before calving compared with d -4, -3, and -2. Additionally, the number of LB increased as both heifers and cows approached labor starting on d -2 and peaked at the day of calving. The time since the activity index increased over 50% to parturition did not differ between heifers and cows, and the activity index revealed the shift in activity on average 6h 14min (range from 2h to 14h 15min) before calf birth. This study provided evidence that heifers and cows approaching parturition showed a similar, but distinct, behavioral pattern that can be observed on average 6h before calf birth. The potential benefits of electronic data loggers as predictors of parturition along with proactive management practices should improve the overall survival and welfare of both the dam and calf. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Analysis of discriminants for experimental 3D SAR imagery of human targets

NASA Astrophysics Data System (ADS)

Chan, Brigitte; Sévigny, Pascale; DiFilippo, David D. J.

2014-10-01

Development of a prototype 3-D through-wall synthetic aperture radar (SAR) system is currently underway at Defence Research and Development Canada. The intent is to map out building wall layouts and to detect targets of interest and their location behind walls such as humans, arms caches, and furniture. This situational awareness capability can be invaluable to the military working in an urban environment. Tools and algorithms are being developed to exploit the resulting 3-D imagery. Current work involves analyzing signatures of targets behind a wall and understanding the clutter and multipath signals in a room of interest. In this paper, a comprehensive study of 3-D human target signature metrics in free space is presented. The aim is to identify features for discrimination of the human target from other targets. Targets used in this investigation include a human standing, a human standing with arms stretched out, a chair, a table, and a metallic plate. Several features were investigated as potential discriminants and five which were identified as good candidates are presented in this paper. Based on this study, no single feature could be used to fully discriminate the human targets from all others. A combination of at least two different features is required to achieve this.

3D Interconnected V6O13 Nanosheets Grown on Carbonized Textile via a Seed-Assisted Hydrothermal Process as High-Performance Flexible Cathodes for Lithium-Ion Batteries

NASA Astrophysics Data System (ADS)

Xu, Shixing; Cen, Dingcheng; Gao, Peibo; Tang, Huang; Bao, Zhihao

2018-03-01

Three-dimensional (3D) free-standing nanostructured materials have been proven to be one of the most promising electrodes for energy storage due to their enhanced electrochemical performance. And they are also widely studied for the wearable energy storage systems. In this work, interconnected V6O13 nanosheets were grown on the flexible carbonized textile (c-textile) via a seed-assisted hydrothermal method to form a 3D free-standing electrode for lithium-ion batteries (LIBs). The electrode exhibited a specific capacity of 170 mA h g-1 at a specific current of 300 mA g-1. With carbon nanotube (CNT) coating, its specific capacities further increased 12-40% at the various current rates. It could retain a reversible capacity of 130 mA h g-1, 74% of the initial capacity after 300 cycles at the specific current of 300 mA g-1. It outperformed most of the mixed-valence vanadium oxides. The improved electrochemical performance was ascribed to the synergistic effect of the 3D nanostructure of V6O13 for feasible Li+ diffusion and transport and highly conductive hierarchical conductive network formed by CNT and carbon fiber in c-textile.

Direct-Write 3D Nanoprinting of Plasmonic Structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winkler, Robert; Schmidt, Franz-Philipp; Karl-Franzens Univ.

During the past decade, significant progress has been made in the field of resonant optics ranging from fundamental aspects to concrete applications. And while several techniques have been introduced for the fabrication of highly defined metallic nanostructures, the synthesis of complex, free-standing three-dimensional (3D) structures is still an intriguing, but so far intractable, challenge. Here, we demonstrate a 3D direct-write synthesis approach that addresses this challenge. Specifically, we succeeded in the direct-write fabrication of 3D nanoarchitectures via electron-stimulated reactions, which are applicable on virtually any material and surface morphology. Furthermore, by that, complex 3D nanostructures composed of highly compact, puremore » gold can be fabricated, which reveal strong plasmonic activity and pave the way for a new generation of 3D nanoplasmonic architectures that can be printed on-demand.« less

Direct-Write 3D Nanoprinting of Plasmonic Structures

DOE PAGES

Winkler, Robert; Schmidt, Franz-Philipp; Karl-Franzens Univ.; ...

2016-11-23

During the past decade, significant progress has been made in the field of resonant optics ranging from fundamental aspects to concrete applications. And while several techniques have been introduced for the fabrication of highly defined metallic nanostructures, the synthesis of complex, free-standing three-dimensional (3D) structures is still an intriguing, but so far intractable, challenge. Here, we demonstrate a 3D direct-write synthesis approach that addresses this challenge. Specifically, we succeeded in the direct-write fabrication of 3D nanoarchitectures via electron-stimulated reactions, which are applicable on virtually any material and surface morphology. Furthermore, by that, complex 3D nanostructures composed of highly compact, puremore » gold can be fabricated, which reveal strong plasmonic activity and pave the way for a new generation of 3D nanoplasmonic architectures that can be printed on-demand.« less

Time budgets of lactating dairy cattle in commercial freestall herds.

PubMed

Gomez, A; Cook, N B

2010-12-01

The aim of this study was to examine the time budgets of 205 lactating dairy cows housed in 16 freestall barns in Wisconsin and to determine the relationships between components of the time budget and herd- and cow-level fixed effects using mixed models. Using continuous video surveillance, time lying in the stall, time standing in the stall, time standing in the alleys (including drinking), time feeding, and time milking (time out of the pen for milking and transit) during a 24-h period were measured for each cow. In addition, the number of lying bouts and the mean duration of each lying bout per 24-h period were determined. Time milking varied between cows from 0.5 to 6.0 h/d, with a mean ± standard deviation of 2.7 ± 1.1h/d. Time milking was influenced significantly by pen stocking density, and time milking negatively affected time feeding, time lying, and time in the alley, but not time standing in the stall. Locomotion score, either directly or through an interaction with stall base type (a rubber crumb-filled mattress, MAT, or sand bedding, SAND), influenced pen activity. Lame cows spent less time feeding, less time in the alleys, and more time standing in the stalls in MAT herds, but not in SAND herds. The effect of lameness on lying time is complex and dependent on the time available for rest and differences in resting behavior observed between cows in MAT and SAND herds. In MAT herds, rest was characterized by a larger number of lying bouts of shorter duration than in SAND herds (mean = 14.4; confidence interval, CI: 12.4 to 16.5 vs. mean = 10.2; CI: 8.2 to 12.2 bouts per d, and mean = 1.0; CI: 0.9 to 1.1 vs. mean = 1.3, CI: 1.2 to 1.4h bout duration for MAT and SAND herds, respectively). Lameness was associated with an increase in time standing in the stall and a reduction in the mean (CI) number of lying bouts per day from 13.2 (CI: 12.3 to 14.1) bouts/d for nonlame cows to 10.9 (CI: 9.30 to 12.8) bouts/d for moderately lame cows, and an overall reduction in lying time in MAT herds compared with SAND herds (11.5; CI: 10.0 to 13.0 vs. 12.7; CI: 11.0 to 14.3h/d, respectively). These results show that time out of the pen milking, stall base type, and lameness significantly affect time budgets of cows housed in freestall facilities. Copyright © 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Modeling biophysical properties of broad-leaved stands in the hyrcanian forests of Iran using fused airborne laser scanner data and ultraCam-D images

NASA Astrophysics Data System (ADS)

Mohammadi, Jahangir; Shataee, Shaban; Namiranian, Manochehr; Næsset, Erik

2017-09-01

Inventories of mixed broad-leaved forests of Iran mainly rely on terrestrial measurements. Due to rapid changes and disturbances and great complexity of the silvicultural systems of these multilayer forests, frequent repetition of conventional ground-based plot surveys is often cost prohibitive. Airborne laser scanning (ALS) and multispectral data offer an alternative or supplement to conventional inventories in the Hyrcanian forests of Iran. In this study, the capability of a combination of ALS and UltraCam-D data to model stand volume, tree density, and basal area using random forest (RF) algorithm was evaluated. Systematic sampling was applied to collect field plot data on a 150 m × 200 m sampling grid within a 1100 ha study area located at 36°38‧- 36°42‧N and 54°24‧-54°25‧E. A total of 308 circular plots (0.1 ha) were measured for calculation of stand volume, tree density, and basal area per hectare. For each plot, a set of variables was extracted from both ALS and multispectral data. The RF algorithm was used for modeling of the biophysical properties using ALS and UltraCam-D data separately and combined. The results showed that combining the ALS data and UltraCam-D images provided a slight increase in prediction accuracy compared to separate modeling. The RMSE as percentage of the mean, the mean difference between observed and predicted values, and standard deviation of the differences using a combination of ALS data and UltraCam-D images in an independent validation at 0.1-ha plot level were 31.7%, 1.1%, and 84 m3 ha-1 for stand volume; 27.2%, 0.86%, and 6.5 m2 ha-1 for basal area, and 35.8%, -4.6%, and 77.9 n ha-1 for tree density, respectively. Based on the results, we conclude that fusion of ALS and UltraCam-D data may be useful for modeling of stand volume, basal area, and tree density and thus gain insights into structural characteristics in the complex Hyrcanian forests.

Development and Analysis of SRIC Harvesting Systems

Treesearch

Bryce J. Stokes; Bruce R. Hartsough

1993-01-01

This paper reviews several machine combinations for harvesting short-rotation, intensive-culture (SRIC) plantations. Productivity and cost information for individual machines was obtained from published sources. Three felling and skidding systems were analyzed for two stands, a 7.6-cm (3-in) average d.b.h. sycamore and a 15.2-cm (6-in) average d.b.h. eucalyptus. The...

Ultra-high-speed 3D astigmatic particle tracking velocimetry: application to particle-laden supersonic impinging jets

NASA Astrophysics Data System (ADS)

Buchmann, N. A.; Cierpka, C.; Kähler, C. J.; Soria, J.

2014-11-01

The paper demonstrates ultra-high-speed three-component, three-dimensional (3C3D) velocity measurements of micron-sized particles suspended in a supersonic impinging jet flow. Understanding the dynamics of individual particles in such flows is important for the design of particle impactors for drug delivery or cold gas dynamic spray processing. The underexpanded jet flow is produced via a converging nozzle, and micron-sized particles ( d p = 110 μm) are introduced into the gas flow. The supersonic jet impinges onto a flat surface, and the particle impact velocity and particle impact angle are studied for a range of flow conditions and impingement distances. The imaging system consists of an ultra-high-speed digital camera (Shimadzu HPV-1) capable of recording rates of up to 1 Mfps. Astigmatism particle tracking velocimetry (APTV) is used to measure the 3D particle position (Cierpka et al., Meas Sci Technol 21(045401):13, 2010) by coding the particle depth location in the 2D images by adding a cylindrical lens to the high-speed imaging system. Based on the reconstructed 3D particle positions, the particle trajectories are obtained via a higher-order tracking scheme that takes advantage of the high temporal resolution to increase robustness and accuracy of the measurement. It is shown that the particle velocity and impingement angle are affected by the gas flow in a manner depending on the nozzle pressure ratio and stand-off distance where higher pressure ratios and stand-off distances lead to higher impact velocities and larger impact angles.

Credit WCT. Photographic copy of photograph, view east southeast across ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view east southeast across Dd station ejectors showing detail of "Hyprox" steam generator. Note that steam generator is placed above Z-stage ejector; an insulated pipe running between the Dd train rails supplies steam to the Y-Stage ejector. Note emergency eyewash stand at extreme right of view. (JPL negative no. 384-3376, 3 December 1962) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Resonance fluorescence microscopy via three-dimensional atom localization

NASA Astrophysics Data System (ADS)

Panchadhyayee, Pradipta; Dutta, Bibhas Kumar; Das, Nityananda; Mahapatra, Prasanta Kumar

2018-02-01

A scheme is proposed to realize three-dimensional (3D) atom localization in a driven two-level atomic system via resonance fluorescence. The field arrangement for the atom localization involves the application of three mutually orthogonal standing-wave fields and an additional traveling-wave coupling field. We have shown the efficacy of such field arrangement in tuning the spatially modulated resonance in all directions. Under different parametric conditions, the 3D localization patterns originate with various shapes such as sphere, sheets, disk, bowling pin, snake flute, flower vase. High-precision localization is achieved when the radiation field detuning equals twice the combined Rabi frequencies of the standing-wave fields. Application of a traveling-wave field of suitable amplitude at optimum radiation field detuning under symmetric standing-wave configuration leads to 100% detection probability even in sub-wavelength domain. Asymmetric field configuration is also taken into consideration to exhibit atom localization with appreciable precision compared to that of the symmetric case. The momentum distribution of the localized atoms is found to follow the Heisenberg uncertainty principle under the validity of Raman-Nath approximation. The proposed field configuration is suitable for application in the study of atom localization in an optical lattice arrangement.

Walking patterns and hip contact forces in patients with hip dysplasia.

PubMed

Skalshøi, Ole; Iversen, Christian Hauskov; Nielsen, Dennis Brandborg; Jacobsen, Julie; Mechlenburg, Inger; Søballe, Kjeld; Sørensen, Henrik

2015-10-01

Several studies have investigated walking characteristics in hip dysplasia patients, but so far none have described all hip rotational degrees of freedom during the whole gait cycle. This descriptive study reports 3D joint angles and torques, and furthermore extends previous studies with muscle and joint contact forces in 32 hip dysplasia patients and 32 matching controls. 3D motion capture data from walking and standing trials were analysed. Hip, knee, ankle and pelvis angles were calculated with inverse kinematics for both standing and walking trials. Hip, knee and ankle torques were calculated with inverse dynamics, while hip muscle and joint contact forces were calculated with static optimisation for the walking trials. No differences were found between the two groups while standing. While walking, patients showed decreased hip extension, increased ankle pronation and increased hip abduction and external rotation torques. Furthermore, hip muscle forces were generally lower and shifted to more posteriorly situated muscles, while the hip joint contact force was lower and directed more superiorly. During walking, patients showed lower and more superiorly directed hip joint contact force, which might alleviate pain from an antero-superiorly degenerated joint. Copyright © 2015 Elsevier B.V. All rights reserved.

Test stand for Titan 34D SRM static firing

NASA Technical Reports Server (NTRS)

Glozman, Vladimir; Shipway, George

1988-01-01

An existing liquid engine test stand at the AF Astronautics Laboratory was refurbished and extensively modified to accommodate the static firing of the Titan 34D solid rocket motor (SRM) in the vertical nozzle down orientation. The main load restraint structure was designed and built to secure the SRM from lifting off during the firing. In addition, the structure provided weather protection, temperature conditioning of the SRM, and positioning of the measurement and recording equipment. The structure was also used for stacking/de-stacking of SRM segments and other technological processes. The existing stand, its foundation and anchorage were thoroughly examined and reanalyzed. Necessary stand modifications were carried out to comply with the requirements of the Titan 34D SRM static firing.

Comfort zone-design free stalls: do they influence the stall use behavior of lame cows?

PubMed

Cook, N B; Marin, M J; Mentink, R L; Bennett, T B; Schaefer, M J

2008-12-01

The behavior of 59 cows in 4 herds, each with Comfort Zone-design free stalls with dimensions suitable for 700-kg, mature Holstein dairy cows, was filmed for a 48-h period. Comparison was made between nonlame, slightly lame, and moderately lame cows on either rubber-crumb-filled mattress stall surfaces bedded with a small amount of sawdust (2 herds) or a Pack Mat design, which consisted of a rubber-crumb-filled mattress pad installed 5 cm below a raised rear curb, bedded with 5 to 8 cm of sand bedding (2 herds). All other stall design components were similar. Despite adequate resting space and freedom to perform normal rising and lying movements, lame cows on mattresses stood in the stall for >2 h longer than nonlame cows. Although a significant increase in stall standing behavior was observed in lame cows on Pack Mat stalls, the mean (95% confidence interval) standing time in the stall was only 0.7 (0 to 3.0) h/d for nonlame cows and 1.6 (0 to 4.2) h/d for moderately lame cows, which was less than the 2.1 (0 to 4.4), 4.3 (1.6 to 6.9), and 4.9 (2.5 to 7.3) h/d spent standing in the stall for nonlame, slightly lame, and moderately lame cows on mattresses, respectively. This observation supports the hypothesis that it is the nature of the stall surface that dictates changes in stall standing behavior observed in lame cows, rather than other components of stall design. The finding that only 5 to 8 cm of sand over a mattress pad provides most of the benefits of deep sand-bedded stalls, along with other advantages related to stall maintenance and manure handling, gives farmers another useful housing alternative with which to improve cow comfort and well-being.

Integrated Energy Solutions | NREL

Science.gov Websites

Transitions A man and woman standing in front of a large, color 3D visualization screen that spans the height a woman and a man testing a scaled model of a microgrid controller in a laboratory setting

Microbial Degradation of Pesticides

DTIC Science & Technology

1981-11-30

with a 2-m glass, 3.2 mm I.D. column, packed with 3% Silar IOC on Gas-Chrom Q, (110-200 mesh) (Applied Science Laboratories, State College, PA) was...allowing the material to stand overnight to form trimethylsilyl (TMS) derivatives of polar compounds. All peaks recovered by GC on Silar 1OC rolumn

Credit BG. Looking northwest at the Dd stand complex. To ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. Looking northwest at the Dd stand complex. To the left is the Test Stand "D" tower with steam-driven ejectors and interstage condenser visible along with steam lines. The steam accumulator appears in the left foreground (sphere); steam lines emerging from the top conduct steam to the Dv, Dd, and Dy stand ejectors. The T-shaped vertical pipes atop the accumulator are burst-disk type safety valves. The ejector ends of the Dd and Dy trains are visible to the right. Tracks permitted each train to expand and contract with temperature or equipment changes - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Large-Scale, Three–Dimensional, Free–Standing, and Mesoporous Metal Oxide Networks for High–Performance Photocatalysis

PubMed Central

Bai, Hua; Li, Xinshi; Hu, Chao; Zhang, Xuan; Li, Junfang; Yan, Yan; Xi, Guangcheng

2013-01-01

Mesoporous nanostructures represent a unique class of photocatalysts with many applications, including splitting of water, degradation of organic contaminants, and reduction of carbon dioxide. In this work, we report a general Lewis acid catalytic template route for the high–yield producing single– and multi–component large–scale three–dimensional (3D) mesoporous metal oxide networks. The large-scale 3D mesoporous metal oxide networks possess large macroscopic scale (millimeter–sized) and mesoporous nanostructure with huge pore volume and large surface exposure area. This method also can be used for the synthesis of large–scale 3D macro/mesoporous hierarchical porous materials and noble metal nanoparticles loaded 3D mesoporous networks. Photocatalytic degradation of Azo dyes demonstrated that the large–scale 3D mesoporous metal oxide networks enable high photocatalytic activity. The present synthetic method can serve as the new design concept for functional 3D mesoporous nanomaterials. PMID:23857595

Does One Size Fit Everyone? Replacement Dose of Levothyroxine in Long-standing Primary Hypothyroidism in Adults

PubMed Central

Singh, Rekha

2017-01-01

Objectives: The recommended starting dose of levothyroxine (LT4) in primary hypothyroidism is 1.6 μg/kg body weight and is based on presumption of minimal residual thyroid function in autoimmune hypothyroidism. This study aimed at finding the range and determining factors for LT4 dose in long-standing hypothyroidism. Methods: A cross-sectional study of individuals with primary autoimmune hypothyroidism on LT4 replacement was done between March 2015 and January 2016. Individuals enrolled were euthyroid based on recent serum thyroid-stimulating hormone. The inclusion criteria included LT4 intake in the morning empty stomach, maintenance of at least 1-h food gap, not on medications known to hamper LT4 absorption within 4 h of dosing, diagnosis of hypothyroidism at least for 1 year, and on a minimum 25 μg LT4. P < 0.05 was considered statistically significant. Results: A total of 346 individuals (290 women and 56 men; 214 premenopausal and 76 postmenopausal women) were enrolled. The mean duration of hypothyroidism and age were 5.7 years and 42.1 years, respectively. The range and mean of absolute LT4 daily dose (ADD), LT4 dose based on body weight (D/W), and LT4 dose based on ideal body weight (D/IBW) were 25–200 μg daily and 77.1 μg, 0.3–2.82 μg/kg and 1.21 μg/kg, and 0.42–3.5 μg/kg and 1.58 μg/kg, respectively. Duration of hypothyroidism was significant predictors of ADD, D/W, and D/IBW. Gender-based difference in ADD and D/IBW was explained by gender difference in anthropometry. Conclusion: Long-standing primary autoimmune hypothyroidism has variable dose requirement of LT4 for achieving euthyroidism and may be dependent on the degree of residual functional thyroid. Duration of hypothyroidism was significant positive predictor for either ADD, D/W, or D/IBW. PMID:28553595

ProQ3D: improved model quality assessments using deep learning.

PubMed

Uziela, Karolis; Menéndez Hurtado, David; Shu, Nanjiang; Wallner, Björn; Elofsson, Arne

2017-05-15

Protein quality assessment is a long-standing problem in bioinformatics. For more than a decade we have developed state-of-art predictors by carefully selecting and optimising inputs to a machine learning method. The correlation has increased from 0.60 in ProQ to 0.81 in ProQ2 and 0.85 in ProQ3 mainly by adding a large set of carefully tuned descriptions of a protein. Here, we show that a substantial improvement can be obtained using exactly the same inputs as in ProQ2 or ProQ3 but replacing the support vector machine by a deep neural network. This improves the Pearson correlation to 0.90 (0.85 using ProQ2 input features). ProQ3D is freely available both as a webserver and a stand-alone program at http://proq3.bioinfo.se/. arne@bioinfo.se. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Expanding options for reforestation of the Cumberland Plateau

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGee, C.E.

1980-01-01

Stems of d.b.h. 4 inches or greater in a low quality stand in Tennessee dominated by white and scarlet oak (Quercus coccinea) were sheared in September-November 1976, chipped, and removed. Sawtimber quality trees (30) in the 37-acre area were felled separately by conventional methods. Residual trees (2-3 inches d.b.h., ht. over 4.5 ft) in some areas were injected with herbicide. One-acre plots were planted with 1+0 loblolly pine, 2+0 white pine (Pinus strobus), or 1+0 yellow poplar, or left to regenerate naturally. After 2 years, survival of all trees was good (83% or over) and average height of loblolly pine,more » yellow poplar and desirable natural stems (white, scarlet or black oak, Quercus velutina) was 3.3 ft, significantly different from that of white pine (1.5 ft). It is concluded that poor quality stands can be cheaply improved by this method, although release from competing vegetation may be necessary, especially in the case of white pine.« less

Repetitive Daily Point of Choice Prompts and Occupational Sit-Stand Transfers, Concentration and Neuromuscular Performance in Office Workers: An RCT

PubMed Central

Donath, Lars; Faude, Oliver; Schefer, Yannick; Roth, Ralf; Zahner, Lukas

2015-01-01

Objective: Prolonged office sitting time adversely affects neuromuscular and cardiovascular health parameters. As a consequence, the present study investigated the effects of prompting the use of height-adjustable working desk (HAWD) on occupational sitting and standing time, neuromuscular outcomes and concentration in office workers. Methods: A single-blinded randomized controlled trial (RCT) with parallel group design was conducted. Thirty-eight office workers were supplied with HAWDs and randomly assigned (Strata: physical activity (PA), BMI, gender, workload) to a prompt (INT) or non-prompt (CON) group. INT received three daily screen-based prompts within 12 weeks. CON was only instructed once concerning the benefits of using HAWDs prior to the start of the study. Sitting and standing times were objectively assessed as primary outcomes for one entire working week using the ActiGraph wGT3X-BT at baseline (pre), after 6 (mid) and 12 weeks (post). Concentration (d2-test), postural sway during upright stance (under single, dual and triple task) and lower limb strength endurance (heel-rise) were collected as secondary outcomes. Results: With large but not statistically significant within group effects from pre to post, INT increased weekly standing time at work by 9% (p = 0.22, d = 0.8) representing an increase from 7.2 h (4.8) to 9.7 (6.6) h (p = 0.07). Concentration and neuromuscular performance did not change from pre to post testing (0.23 < p < 0.95; 0.001 < ηp² < 0.05). Conclusion: Low-frequent and low cost screen-based point of choice prompts (3 per day within 12 weeks) already result in notable increases of occupational standing time of approx. daily 30 min. These stimuli, however, did not relevantly affect neuromuscular outcomes.   PMID:25903058

Effect of free stall surface on daily activity patterns in dairy cows with relevance to lameness prevalence.

PubMed

Cook, N B; Bennett, T B; Nordlund, K V

2004-09-01

Differences in behavior of nonlame cows, slightly lame cows, and moderately lame cows in 6 free stall barns with sand bedding (SAND) vs. 6 free stall barns with rubber-crumb geotextile mattress surfaces (MAT) were documented in Wisconsin dairy herds. All lactating cows in the 12 herds were observed and given a locomotion score based on a 4-point scale: 1 = nonlame, 2 = slightly lame, 3 = moderately lame, and 4 = severely lame. Herd least square means +/-SE for prevalence of clinical lameness (locomotion scores = 3 and 4) were 11.1 vs. 24.0 +/- 1.7% for herds using SAND vs. MAT surfaces, respectively. Subsets of 10 cows per herd with locomotion scores of 1 to 3 were observed via video cameras for 24-h periods. Cows in MAT herds spent more time standing in free stalls per day than cows in SAND herds. Differences in standing times were 0.73 h/d for cows that were not lame, 2.32 h/d for cows that were slightly lame, and 4.31 h/d for cows that were moderately lame in MAT herds compared with equivalent cows in SAND herds. In MAT herds, the increase in time spent standing in the stall in moderately lame cows was associated with a significant reduction in stall use sessions per day, which impacted daily lying time. Although cause and effect are not clear, these findings have implications for housing, comfort, and care of cows in dairy herds with different types of free stall surfaces.

Element sensitive reconstruction of nanostructured surfaces with finite elements and grazing incidence soft X-ray fluorescence.

PubMed

Soltwisch, Victor; Hönicke, Philipp; Kayser, Yves; Eilbracht, Janis; Probst, Jürgen; Scholze, Frank; Beckhoff, Burkhard

2018-03-29

The geometry of a Si3N4 lamellar grating was investigated experimentally with reference-free grazing-incidence X-ray fluorescence analysis. While simple layered systems are usually treated with the matrix formalism to determine the X-ray standing-wave field, this approach fails for laterally structured surfaces. Maxwell solvers based on finite elements are often used to model electrical field strengths for any 2D or 3D structures in the optical spectral range. We show that this approach can also be applied in the field of X-rays. The electrical field distribution obtained with the Maxwell solver can subsequently be used to calculate the fluorescence intensities in full analogy to the X-ray standing-wave field obtained by the matrix formalism. Only the effective 1D integration for the layer system has to be replaced by a 2D integration of the finite elements, taking into account the local excitation conditions. We will show that this approach is capable of reconstructing the geometric line shape of a structured surface with high elemental sensitivity. This combination of GIXRF and finite-element simulations paves the way for a versatile characterization of nanoscale-structured surfaces.

Standing Kink modes in three-dimensional coronal loops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pascoe, D. J.; De Moortel, I., E-mail: dpascoe@mcs.st-andrews.ac.uk

2014-04-01

So far, the straight flux tube model proposed by Edwin and Roberts is the most commonly used tool in practical coronal seismology, in particular, to infer values of the (coronal) magnetic field from observed, standing kink mode oscillations. In this paper, we compare the period predicted by this basic model with three-dimensional (3D) numerical simulations of standing kink mode oscillations, as the period is a crucial parameter in the seismological inversion to determine the magnetic field. We perform numerical simulations of standing kink modes in both straight and curved 3D coronal loops and consider excitation by internal and external drivers.more » The period of oscillation for the displacement of dense coronal loops is determined by the loop length and the kink speed, in agreement with the estimate based on analytical theory for straight flux tubes. For curved coronal loops embedded in a magnetic arcade and excited by an external driver, a secondary mode with a period determined by the loop length and external Alfvén speed is also present. When a low number of oscillations is considered, these two periods can result in a single, non-resolved (broad) peak in the power spectrum, particularly for low values of the density contrast for which the two periods will be relatively similar. In that case (and for this particular geometry), the presence of this additional mode would lead to ambiguous seismological estimates of the magnetic field strength.« less

Muscle Forces and Their Contributions to Vertical and Horizontal Acceleration of the Center of Mass During Sit-to-Stand Transfer in Young, Healthy Adults.

PubMed

Caruthers, Elena J; Thompson, Julie A; Chaudhari, Ajit M W; Schmitt, Laura C; Best, Thomas M; Saul, Katherine R; Siston, Robert A

2016-10-01

Sit-to-stand transfer is a common task that is challenging for older adults and others with musculoskeletal impairments. Associated joint torques and muscle activations have been analyzed two-dimensionally, neglecting possible three-dimensional (3D) compensatory movements in those who struggle with sit-to-stand transfer. Furthermore, how muscles accelerate an individual up and off the chair remains unclear; such knowledge could inform rehabilitation strategies. We examined muscle forces, muscleinduced accelerations, and interlimb muscle force differences during sit-to-stand transfer in young, healthy adults. Dynamic simulations were created using a custom 3D musculoskeletal model; static optimization and induced acceleration analysis were used to determine muscle forces and their induced accelerations, respectively. The gluteus maximus generated the largest force (2009.07 ± 277.31 N) and was a main contributor to forward acceleration of the center of mass (COM) (0.62 ± 0.18 m/s(2)), while the quadriceps opposed it. The soleus was a main contributor to upward (2.56 ± 0.74 m/s(2)) and forward acceleration of the COM (0.62 ± 0.33 m/s(2)). Interlimb muscle force differences were observed, demonstrating lower limb symmetry cannot be assumed during this task, even in healthy adults. These findings establish a baseline from which deficits and compensatory strategies in relevant populations (eg, elderly, osteoarthritis) can be identified.

Behavioral and physiological changes during heat stress in Corriedale ewes exposed to water deprivation.

PubMed

Ghassemi Nejad, Jalil; Sung, Kyung-Il

2017-01-01

This study was conducted to investigate the behavioral and physiological changes of heat stressed Corriedale ewes exposed to water deprivation. Nine Corriedale ewes (average BW = 45 ± 3.7 kg) were individually fed diets based on maintenance requirements in metabolic crates. Ewes were assigned into three groups (9 sheep per treatment) according to a 3 × 3 Latin square design for 3 periods with 21-d duration for each period. The control (CON) group was given free access to water, 2 h water deprivation (2hWD), and 3 h water deprivation (3hWD) following feeding. No differences were found in fecal excretion frequency, standing frequency (number/d), and sitting frequency among the groups ( p  > 0.05). Measurements of standing duration (min/d) and urine excretion frequency (number/d) showed a significant decrease whereas sitting duration (min/d) showed a significant increase in the 2hWD and 3hWD groups when compared with the CON group ( p  < 0.05). Fecal score and heart rate (number/min) were not different among the groups ( p  > 0.05). However, respiratory rate (number/min) and panting score were found to be significantly higher in the 2hWD and 3hWD groups than in the CON group ( p  < 0.05). It is concluded that water deprivation following feeding intensifies physiological heat stress related indicators such as respiratory rate and panting score and changes behavioral parameters such as water intake and urine excretion frequency in heat stressed ewes. Daily adaptation to the extreme environmental conditions may occur actively in ewes.

Credit WCT. Photographic copy of photograph, view of Test Stand ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view of Test Stand "D" from the south with tower ejector system in operation during a 1972 engine test. Note steam evolving from Z-stage ejectors atop the interstage condenser in the tower. Note also the "Hyprox" steam generator straddling the Dd ejector train to the right. The new Dy horizontal train has not been erected as of this date. In the distance is Test Stand "E." (JPL negative no. 384-9766-AC, 28 November 1972) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Effect of revised high-heeled shoes on foot pressure and static balance during standing.

PubMed

Bae, Young-Hyeon; Ko, Mansoo; Park, Young-Soul; Lee, Suk-Min

2015-04-01

[Purpose] The purpose of this study was to investigate the effects of revised high-heeled shoes on the foot pressure ratio and static balance during standing. [Subjects and Methods] A single-subject design was used, 15 healthy women wearing revised high-heeled shoes and general high-heeled shoes in a random order. The foot pressure ratio and static balance scores during standing were measured using a SpaceBalance 3D system. [Results] Forefoot and rearfoot pressures were significantly different between the 2 types of high-heeled shoes. Under the 3 conditions tested, the static balance score was higher for the revised high-heeled shoes than for the general high-heeled shoes, but this difference was not statistically significant. [Conclusion] Revised high-heeled shoes are preferable to general high-heeled shoes, as they result in normalization of normalized foot pressure and a positive effect on static balance.

Effect of revised high-heeled shoes on foot pressure and static balance during standing

PubMed Central

Bae, Young-Hyeon; Ko, Mansoo; Park, Young-Soul; Lee, Suk-Min

2015-01-01

[Purpose] The purpose of this study was to investigate the effects of revised high-heeled shoes on the foot pressure ratio and static balance during standing. [Subjects and Methods] A single-subject design was used, 15 healthy women wearing revised high-heeled shoes and general high-heeled shoes in a random order. The foot pressure ratio and static balance scores during standing were measured using a SpaceBalance 3D system. [Results] Forefoot and rearfoot pressures were significantly different between the 2 types of high-heeled shoes. Under the 3 conditions tested, the static balance score was higher for the revised high-heeled shoes than for the general high-heeled shoes, but this difference was not statistically significant. [Conclusion] Revised high-heeled shoes are preferable to general high-heeled shoes, as they result in normalization of normalized foot pressure and a positive effect on static balance. PMID:25995572

An innovative stand-alone bioreactor for the highly reproducible transfer of cyclic mechanical stretch to stem cells cultured in a 3D scaffold.

PubMed

Govoni, Marco; Lotti, Fabrizio; Biagiotti, Luigi; Lannocca, Maurizio; Pasquinelli, Gianandrea; Valente, Sabrina; Muscari, Claudio; Bonafè, Francesca; Caldarera, Claudio M; Guarnieri, Carlo; Cavalcanti, Silvio; Giordano, Emanuele

2014-10-01

Much evidence in the literature demonstrates the effect of cyclic mechanical stretch in maintaining, or addressing, a muscle phenotype. Such results were obtained using several technical approaches, useful for the experimental collection of proofs of principle but probably unsuitable for application in clinical regenerative medicine. Here we aimed to design a reliable innovative bioreactor, acting as a stand-alone cell culture incubator, easy to operate and effective in addressing mesenchymal stem cells (MSCs) seeded onto a 3D bioreabsorbable scaffold, towards a muscle phenotype via the transfer of a controlled and highly-reproducible cyclic deformation. Electron microscopy, immunohistochemistry and biochemical analysis of the obtained pseudotissue constructs showed that cells 'trained' over 1 week: (a) displayed multilayer organization and invaded the 3D mesh of the scaffold; and (b) expressed typical markers of muscle cells. This effect was due only to physical stimulation of the cells, without the need of any other chemical or genetic manipulation. This device is thus proposed as a prototypal instrument to obtain pseudotissue constructs to test in cardiovascular regenerative medicine, using good manufacturing procedures. Copyright © 2012 John Wiley & Sons, Ltd.

Nocturnal diastolic blood pressure decline is associated with higher 25-hydroxyvitamin D level and standing plasma renin activity in a hypertensive population.

PubMed

Zhang, Mingchen; Xu, Xinjuan; Liu, Haiming; Li, Haixia; Zhang, Junshi; Gao, Min

2017-01-01

Patients with nondipper hypertension are known to carry a high risk of cardiovascular complications. Vitamin D deficiency is associated with hypertension. Because vitamin D deficiency activates the renin-angiotensin-aldosterone system (RAAS), we hypothesized that this vitamin would interact with the RAAS to influence blood pressure (BP) in nondipper hypertensive patients. We performed a cross-sectional analysis of 1,007 outpatients with hypertension (HTN). Dipper and nondipper patterns were detected, and the two groups were matched for clinical, laboratory, 25-hydroxyvitamin D (25OHD) levels, and ambulatory blood pressure recording. Plasma renin activity (PRA), angiotensin II, and plasma aldosterone concentration (PAC) were assessed in 174 patients treated with calcium channel blockers or no medication. The mean 25OHD concentration in the entire study population was 12.3ng/dL, and the prevalence of vitamin D deficiency was 87.0%. Dipper and nondipper HTN were noted in 187 patients (24.6%) and 573 patients (75.4%). 25OHD levels were similar between nondipper and dipper HTN groups. Forward stepwise logistic regression analysis showed that BMI and age were independent predictors of nondipper HTN. Neither 25OHD levels nor RAAS components were included in the model. In correlation analyses, nocturnal decline of diastolic BP was positively associated with 25OHD levels and standing PRA (r = 0.152 p = 0.045, r = 0.165 p = 0.038, respectively). The present study showed that vitamin D deficiency was astonishingly prevalent in hypertensive subjects residing in Xinjiang, China. There may be a weakly association of nocturnal DBP decline with 25OHD levels and standing PRA levels. We found no association between vitamin D deficiency and nondipper HTN.

A new method for sudden mechanical perturbation with axial load, to assess postural control in sitting and standing.

PubMed

Claus, Andrew P; Verrel, Julius; Pounds, Paul E I; Shaw, Renee C; Brady, Niamh; Chew, Min T; Dekkers, Thomas A; Hodges, Paul W

2016-05-03

Sudden application of load along a sagittal or coronal axis has been used to study trunk stiffness, but not axial (vertical) load. This study introduces a new method for sudden-release axial load perturbation. Prima facie validity was supported by comparison with standard mechanical systems. We report the response of the human body to axial perturbation in sitting and standing and within-day repeatability of measures. Load of 20% of body weight was released from light contact onto the shoulders of 22 healthy participants (10 males). Force input was measured via force transducers at shoulders, output via a force plate below the participant, and kinematics via 3-D motion capture. System identification was used to fit data from the time of load release to time of peak load-displacement, fitting with a 2nd-order mass-spring-damper system with a delay term. At peak load-displacement, the mean (SD) effective stiffness measured with this device for participants in sitting was 12.0(3.4)N/mm, and in standing was 13.3(4.2)N/mm. Peak force output exceeded input by 44.8 (10.0)% in sitting and by 30.4(7.9)% in standing. Intra-class correlation coefficients for within-day repeatability of axial stiffness were 0.58 (CI: -0.03 to 0.83) in sitting and 0.82(0.57-0.93) in standing. Despite greater degrees of freedom in standing than sitting, standing involved lesser time, downward displacement, peak output force and was more repeatable in defending upright postural control against the same axial loads. This method provides a foundation for future studies of neuromuscular control with axial perturbation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Credit WCT. Photographic copy of photograph, view looking northwest at ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view looking northwest at complete Test Stand "D" installation as of January 1962. Note closed-circuit television camera at extreme left, along with MMH (fuel) storage tank. Hatch of Dd test cell is open; nearby stand MMH run tanks for Dd station. (JPL negative no. 384-2591-A, 25 January 1961) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Photographic copy of photograph, aerial view looking south at Jet ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph, aerial view looking south at Jet Propulsion Laboratory, Edwards Test Station complex in 1959, shortly after completion of Test Stand 'D' construction and installation of underground tunnel system. Test Stand 'D' is in the foreground, Test Stand 'A' complex in the background. Roads are as yet unpaved. (JPL negative no. 384-1917-B, 28 May 1959) - Jet Propulsion Laboratory Edwards Facility, Edwards Air Force Base, Boron, Kern County, CA

The association of ACE, ACTN3 and PPARA gene variants with strength phenotypes in middle school-age children.

PubMed

Ahmetov, Ildus I; Gavrilov, Dmitry N; Astratenkova, Irina V; Druzhevskaya, Anastasiya M; Malinin, Alexandr V; Romanova, Elena E; Rogozkin, Victor A

2013-01-01

The aim of the study was to determine the association between ACE I/D, ACTN3 R577X and PPARA intron 7 G/C gene polymorphisms and strength-related traits in 457 middle school-age children (219 boys and 238 girls; aged 11 ± 0.4 years). The assessment of different phenotypes was conducted with a number of performance tests. Gene polymorphisms were determined by PCR. The ACE D allele was associated with high results of standing long-jump test in boys [II 148.3 (16.3) cm, ID 152.6 (19.6) cm, DD 158.2 (19.1) cm; P = 0.037]. The ACTN3 R allele was associated with high results of performance tests in males only in combination with other genes (standing long-jump test: P = 0.021; handgrip strength test: P < 0.0001). Furthermore, the male carriers of the PPARA gene C allele demonstrated the best results of handgrip strength testing than GG homozygotes [GG 14.6 (4.0) kg, GC/CC 15.7 (4.3) kg; P = 0.048]. Thus, the ACE, ACTN3 and PPARA gene variants are associated with strength-related traits in physically active middle school-age boys.

A 3PG-based Model to Simulate Delta-13C Content in Three Tree Species in The Mica Creek Experiment Watershed, Idaho

NASA Astrophysics Data System (ADS)

Wei, L.; Marshall, J. D.

2007-12-01

3PG (Physiological Principles in Predicting Growth), a process-based physiological model of forest productivity, has been widely used and well validated. Based on 3PG, a 3PG-δ13C model to simulate δ13C content in plant tissue is built in this research. 3PG calculates carbon assimilation from utilizable absorbed photosynthetically active radiation (PAR), and calculates stomatal conductance from maximum canopy conductance multiplied by physiological modifier which includes the effect of water vapor deficit and soil water. Then the equation of Farquhar and Sharkey (1982) was used to calculate δ13C content in plant. Five even-aged coniferous forest stands located near Clarkia, Idaho (47°15'N, 115°25'W) in Mica Creek Experimental Watershed, were chosen to test the model, (2 stands had been partial cut (50% canopy removal in 1990) and 3 were uncut). MCEW has been extensively investigated since 1990 and many necessary parameters needed for 3PG are readily available. Each of these sites is located near a UI Meteorological station, which recorded half-hourly climatic data since 2003. These site-specific climatic data were extend to 1991 by correlating with data from a nearby SNOTEL station (SNOwpack TELemetry, NRCS, 47°9' N, 116°16' W). Forest mensuration data were obtained form each stand using variable radius plots (VRP). Three tree species, which consist more than 95% of all trees, were parameterized for 3PG model, including: grand fir (Abies grandis Donn ex D. Don), western red cedar (Thuja plicat Donn ex D. Don a) and Douglas-fir (Pseudotsuga menziesii var. glauca (Beissn.) Franco). Because 4 out of 5 stands have mixed species, we also used parameters for mixed stands to run the model. To stabilize, the model was initially run under average climatic data for 20 years, and then run under the actual climatic data from 1991 to 2006. As 3PG runs in a monthly time step, monthly δ13C values were calculated first, and then yearly values were calculated by weighted averages. For testing the model, tree cores were collected from each stand and species. Ring-widths of tree cores were measured and cross-dated with a ring-width chronology obtained from MCEW. δ13C contents of tree- ring samples from known year were tested. Preliminary results indicate 3PG-δ13C simulated values are consistent with observed values in tree-rings. δ13C values of modeled species are different: western red cider has the highest delta13C values among the three species and western larch has the lowest.

Workplace standing time and the incidence of obesity and type 2 diabetes: a longitudinal study in adults.

PubMed

Chaput, Jean-Philippe; Saunders, Travis J; Tremblay, Mark S; Katzmarzyk, Peter T; Tremblay, Angelo; Bouchard, Claude

2015-02-10

It is increasingly recognized that standing represents a simple solution to extended periods of sitting. However, it is currently unknown whether workplace standing time is prospectively associated with a lower incidence of chronic diseases. The objective of this study was to examine the association between workplace standing time and the incidence of overweight/obesity (OW/OB) and impaired glucose tolerance/type 2 diabetes (IGT/T2D) in adults. A longitudinal analysis from the Quebec Family Study (Canada) was conducted on 293 participants, aged 18 to 65 years, followed for a mean of 6 years. Information on self-reported occupational standing time as well as several covariates was collected at both baseline and follow-up. Outcome measures included the development of OW/OB (i.e. body mass index ≥25 kg/m(2)) and IGT/T2D (i.e. 2-h postload plasma glucose level ≥7.8 mmol/L). The incidence rates of OW/OB and IGT/T2D over the 6-year follow-up period were 17.4% and 12.6%, respectively. Significant negative associations were observed between the amount of occupational standing time and the development of outcome measures. However, the associations were no longer significant after adjustment for age, sex, smoking habits, total annual family income, daily caloric intake, and submaximal working capacity. In age- and sex-adjusted logistic regression analysis, significant negative linear trends were observed across levels of standing time and the outcome variables. However, the associations were no longer significant after further adjustment for the other covariates. Finally, we observed that the change in standing time from baseline to year 6 was significantly associated with the development of outcome measures, with higher incidence rates in adults reporting a reduction in standing time at follow-up. However, the associations became non-significant after adjustment for covariates. Greater occupational standing time is not sufficient in and of itself to prevent the development of OW/OB and IGT/T2D in adults. Future efforts are needed to better understand the potential benefits of higher amounts of standing time throughout the day on the prevention of chronic diseases.

Effects of DanceSport on walking balance and standing balance among the elderly.

PubMed

Sohn, Jeehoon; Park, Sung-Ha; Kim, Sukwon

2018-05-04

Dancesport is a popular activity among older adults who look for fun and fitness in Korea. Studies reported positive sociological and psychological effects of dancesport. But, little studies were performed to evaluate the effects of dancesport on balance performances. The objective of the present study was to evaluate the effects of dancesport for 15 weeks on walking balance and standing balance of older adults. Older adults regularly participated in the dancesport program 3 times a week for 15 weeks. The program included Rumba, Cha-cha-cha, and Jive. They exercised the prescribed dancesport at intermediate level for 50-60 mins for each time. A total 22 reflective markers were placed on the anatomical landmarks and 8 cameras were used to measure 3-D positions of participants. Also, center of pressure (COP) data were measured to analyze standing balance using a ground reaction board at 1200 Hz for 30 seconds. One-way analysis of variance (ANOVA) was performed to test the effects of 15 weeks of dancesport on walking balance and standing balance. The results suggested that, after 15 weeks of dancesport participation, older adults' walking balance (48.3 ± 20.3 cm2 vs 38.2 ± 18.2 cm2) and standing balance (COP area: 189.4 ± 85.4 mm2 vs 103.5 ± 55.4mm2, COP distance: 84.2 ± 34.4 cm vs 76.5 ± 21.4 cm) were significantly improved. Performing dancesport would require moving center of mass rapidly and frequently while maintaining posture. This may result in improving walking balance and standing balance in the present study. The study concluded that dancesport would be an effective exercise method in enhancing postural stability of older adults.

Twin robotic x-ray system for 2D radiographic and 3D cone-beam CT imaging

NASA Astrophysics Data System (ADS)

Fieselmann, Andreas; Steinbrener, Jan; Jerebko, Anna K.; Voigt, Johannes M.; Scholz, Rosemarie; Ritschl, Ludwig; Mertelmeier, Thomas

2016-03-01

In this work, we provide an initial characterization of a novel twin robotic X-ray system. This system is equipped with two motor-driven telescopic arms carrying X-ray tube and flat-panel detector, respectively. 2D radiographs and fluoroscopic image sequences can be obtained from different viewing angles. Projection data for 3D cone-beam CT reconstruction can be acquired during simultaneous movement of the arms along dedicated scanning trajectories. We provide an initial evaluation of the 3D image quality based on phantom scans and clinical images. Furthermore, initial evaluation of patient dose is conducted. The results show that the system delivers high image quality for a range of medical applications. In particular, high spatial resolution enables adequate visualization of bone structures. This system allows 3D X-ray scanning of patients in standing and weight-bearing position. It could enable new 2D/3D imaging workflows in musculoskeletal imaging and improve diagnosis of musculoskeletal disorders.

Credit WCT. Photographic copy of photograph, view looking east at ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view looking east at Test Stand "D" during erection of the test stand tower. Note wire lath nailed over gypsum board on Building 4222/E-23 at far left in preparation for stucco covering (temporary construction). Stucco would not require painting in desert. (JPL negative no. 384-1865-A, 13 April 1959) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Comparison of the PHISICS/RELAP5-3D Ring and Block Model Results for Phase I of the OECD MHTGR-350 Benchmark

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerhard Strydom

2014-04-01

The INL PHISICS code system consists of three modules providing improved core simulation capability: INSTANT (performing 3D nodal transport core calculations), MRTAU (depletion and decay heat generation) and a perturbation/mixer module. Coupling of the PHISICS code suite to the thermal hydraulics system code RELAP5-3D has recently been finalized, and as part of the code verification and validation program the exercises defined for Phase I of the OECD/NEA MHTGR 350 MW Benchmark were completed. This paper provides an overview of the MHTGR Benchmark, and presents selected results of the three steady state exercises 1-3 defined for Phase I. For Exercise 1,more » a stand-alone steady-state neutronics solution for an End of Equilibrium Cycle Modular High Temperature Reactor (MHTGR) was calculated with INSTANT, using the provided geometry, material descriptions, and detailed cross-section libraries. Exercise 2 required the modeling of a stand-alone thermal fluids solution. The RELAP5-3D results of four sub-cases are discussed, consisting of various combinations of coolant bypass flows and material thermophysical properties. Exercise 3 combined the first two exercises in a coupled neutronics and thermal fluids solution, and the coupled code suite PHISICS/RELAP5-3D was used to calculate the results of two sub-cases. The main focus of the paper is a comparison of the traditional RELAP5-3D “ring” model approach vs. a much more detailed model that include kinetics feedback on individual block level and thermal feedbacks on a triangular sub-mesh. The higher fidelity of the block model is illustrated with comparison results on the temperature, power density and flux distributions, and the typical under-predictions produced by the ring model approach are highlighted.« less

Engineering and Design Criteria for Navy Facilities.

DTIC Science & Technology

1987-11-20

ELECTRIC, AND STANDS, GRIDDLE MI L-R-2357G (2) OCT. 1980 G INT AMD 3 RANGE, GAS, (CCMMERCIAL) HEAVY DUTY MI L-D-2467F JUL. 1987 E MAR. 1974. DOUGH ...3420D PACKAGING MATERIALS, VOLATILE CORROSION !NHIBITOR, TREATED, OPAQUE d~~ .; . . . .p -. % . % " - " MIL-D-3886F NOV i986 E P E 8 978 DOUGH ...10388G APR. 1982 PIPE FITTING, ONE OR MORE ENDS GPOVED MIL-S-1 1183E JUN. 1977 SCALE, DIAL AND BEAM INDICATING, BAKERS, DOUGH PIECE CHECK I NG MIL-M

Magnetized SASI: its mechanism and possible connection to some QPOs in XRBs

NASA Astrophysics Data System (ADS)

Dhang, Prasun; Sharma, Prateek; Mukhopadhyay, Banibrata

2018-05-01

The presence of a surface at the inner boundary, such as in a neutron star or a white dwarf, allows the existence of a standing shock in steady spherical accretion. The standing shock can become unstable in 2D or 3D; this is called the standing accretion shock instability (SASI). Two mechanisms - advective-acoustic and purely acoustic - have been proposed to explain SASI. Using axisymmetric hydrodynamic and magnetohydrodynamic simulations, we find that the advective-acoustic mechanism better matches the observed oscillation time-scales in our simulations. The global shock oscillations present in the accretion flow can explain many observed high frequency (≳100 Hz) quasi-periodic oscillations (QPOs) in X-ray binaries. The presence of a moderately strong magnetic field adds more features to the shock oscillation pattern, giving rise to low frequency modulation in the computed light curve. This low frequency modulation can be responsible for ˜100 Hz QPOs (known as hHz QPOs). We propose that the appearance of hHz QPO determines the separation of twin peak QPOs of higher frequencies.

Response of sapling stands to cultural treatments

Treesearch

H. Clay Smith

1989-01-01

The main reasons for precommercial cultural practices in sapling stands (trees less than 5 inches d.b.h.) are to increase growth of residual trees, increase stand value, and improve or maintain species composition. On good sites (northern red oak site index 70 and above), treating sapling stands may be justified by increased diameter growth of high value species. On...

Silvicultural treatments in sapling stands

Treesearch

Neil I. Lamson

1989-01-01

Sapling stands are those in which codominant trees average less than 5 inches d.b.h. Silvicultural treatments in sapling stands can be summed up in two words: CROP TREES. Any silvicultural treatment must help crop trees if the investment in sapling stands is going to pay off. Just cutting "bad" or "undesirable" trees does not insure that crop trees...

Water use of a multigenotype poplar short-rotation coppice from tree to stand scale.

PubMed

Bloemen, Jasper; Fichot, Régis; Horemans, Joanna A; Broeckx, Laura S; Verlinden, Melanie S; Zenone, Terenzio; Ceulemans, Reinhart

2017-02-01

Short-rotation coppice (SRC) has great potential for supplying biomass-based heat and energy, but little is known about SRC's ecological footprint, particularly its impact on the water cycle. To this end, we quantified the water use of a commercial scale poplar ( Populus ) SRC plantation in East Flanders (Belgium) at tree and stand level, focusing primarily on the transpiration component. First, we used the AquaCrop model and eddy covariance flux data to analyse the different components of the stand-level water balance for one entire growing season. Transpiration represented 59% of evapotranspiration (ET) at stand scale over the whole year. Measured ET and modelled ET were lower as compared to the ET of reference grassland, suggesting that the SRC only used a limited amount of water. Secondly, we compared leaf area scaled and sapwood area scaled sap flow ( F s ) measurements on individual plants vs. stand scale eddy covariance flux data during a 39-day intensive field campaign in late summer 2011. Daily stem diameter variation (∆ D ) was monitored simultaneously with F s to understand water use strategies for three poplar genotypes. Canopy transpiration based on sapwood area or leaf area scaling was 43.5 and 50.3 mm, respectively, and accounted for 74%, respectively, 86%, of total ecosystem ET measured during the intensive field campaign. Besides differences in growth, the significant intergenotypic differences in daily ∆ D (due to stem shrinkage and swelling) suggested different water use strategies among the three genotypes which were confirmed by the sap flow measurements. Future studies on the prediction of SRC water use, or efforts to enhance the biomass yield of SRC genotypes, should consider intergenotypic differences in transpiration water losses at tree level as well as the SRC water balance at stand level.

Validity of the Microsoft Kinect for assessment of postural control.

PubMed

Clark, Ross A; Pua, Yong-Hao; Fortin, Karine; Ritchie, Callan; Webster, Kate E; Denehy, Linda; Bryant, Adam L

2012-07-01

Clinically feasible methods of assessing postural control such as timed standing balance and functional reach tests provide important information, however, they cannot accurately quantify specific postural control mechanisms. The Microsoft Kinect™ system provides real-time anatomical landmark position data in three dimensions (3D), and given that it is inexpensive, portable and simple to setup it may bridge this gap. This study assessed the concurrent validity of the Microsoft Kinect™ against a benchmark reference, a multiple-camera 3D motion analysis system, in 20 healthy subjects during three postural control tests: (i) forward reach, (ii) lateral reach, and (iii) single-leg eyes-closed standing balance. For the reach tests, the outcome measures consisted of distance reached and trunk flexion angle in the sagittal (forward reach) and coronal (lateral reach) planes. For the standing balance test the range and deviation of movement in the anatomical landmark positions for the sternum, pelvis, knee and ankle and the lateral and anterior trunk flexion angle were assessed. The Microsoft Kinect™ and 3D motion analysis systems had comparable inter-trial reliability (ICC difference=0.06±0.05; range, 0.00-0.16) and excellent concurrent validity, with Pearson's r-values >0.90 for the majority of measurements (r=0.96±0.04; range, 0.84-0.99). However, ordinary least products analyses demonstrated proportional biases for some outcome measures associated with the pelvis and sternum. These findings suggest that the Microsoft Kinect™ can validly assess kinematic strategies of postural control. Given the potential benefits it could therefore become a useful tool for assessing postural control in the clinical setting. Copyright © 2012 Elsevier B.V. All rights reserved.

Development and performance evaluation of a three-dimensional clinostat synchronized heavy-ion irradiation system.

PubMed

Ikeda, Hiroko; Souda, Hikaru; Puspitasari, Anggraeini; Held, Kathryn D; Hidema, Jun; Nikawa, Takeshi; Yoshida, Yukari; Kanai, Tatsuaki; Takahashi, Akihisa

2017-02-01

Outer space is an environment characterized by microgravity and space radiation, including high-energy charged particles. Astronauts are constantly exposed to both microgravity and radiation during long-term stays in space. However, many aspects of the biological effects of combined microgravity and space radiation remain unclear. We developed a new three-dimensional (3D) clinostat synchronized heavy-ion irradiation system for use in ground-based studies of the combined exposures. Our new system uses a particle accelerator and a respiratory gating system from heavy-ion radiotherapy to irradiate samples being rotated in the 3D clinostat with carbon-ion beams only when the samples are in the horizontal position. A Peltier module and special sample holder were loaded on a static stage (standing condition) and the 3D clinostat (rotation condition) to maintain a suitable temperature under atmospheric conditions. The performance of the new device was investigated with normal human fibroblasts 1BR-hTERT in a disposable closed cell culture chamber. Live imaging revealed that cellular adhesion and growth were almost the same for the standing control sample and rotation sample over 48h. Dose flatness and symmetry were judged according to the relative density of Gafchromic films along the X-axis and Y-axis of the positions of the irradiated sample to confirm irradiation accuracy. Doses calculated using the carbon-ion calibration curve were almost the same for standing and rotation conditions, with the difference being less than 5% at 1Gy carbon-ion irradiation. Our new device can accurately synchronize carbon-ion irradiation and simulated microgravity while maintaining the temperature under atmospheric conditions at ground level. Copyright © 2017 The Committee on Space Research (COSPAR). Published by Elsevier Ltd. All rights reserved.

Evaluating biomechanics of user-selected sitting and standing computer workstation.

PubMed

Lin, Michael Y; Barbir, Ana; Dennerlein, Jack T

2017-11-01

A standing computer workstation has now become a popular modern work place intervention to reduce sedentary behavior at work. However, user's interaction related to a standing computer workstation and its differences with a sitting workstation need to be understood to assist in developing recommendations for use and set up. The study compared the differences in upper extremity posture and muscle activity between user-selected sitting and standing workstation setups. Twenty participants (10 females, 10 males) volunteered for the study. 3-D posture, surface electromyography, and user-reported discomfort were measured while completing simulated tasks with each participant's self-selected workstation setups. Sitting computer workstation associated with more non-neutral shoulder postures and greater shoulder muscle activity, while standing computer workstation induced greater wrist adduction angle and greater extensor carpi radialis muscle activity. Sitting computer workstation also associated with greater shoulder abduction postural variation (90th-10th percentile) while standing computer workstation associated with greater variation for should rotation and wrist extension. Users reported similar overall discomfort levels within the first 10 min of work but had more than twice as much discomfort while standing than sitting after 45 min; with most discomfort reported in the low back for standing and shoulder for sitting. These different measures provide understanding in users' different interactions with sitting and standing and by alternating between the two configurations in short bouts may be a way of changing the loading pattern on the upper extremity. Copyright © 2017 Elsevier Ltd. All rights reserved.

3D digital image correlation using single color camera pseudo-stereo system

NASA Astrophysics Data System (ADS)

Li, Junrui; Dan, Xizuo; Xu, Wan; Wang, Yonghong; Yang, Guobiao; Yang, Lianxiang

2017-10-01

Three dimensional digital image correlation (3D-DIC) has been widely used by industry to measure the 3D contour and whole-field displacement/strain. In this paper, a novel single color camera 3D-DIC setup, using a reflection-based pseudo-stereo system, is proposed. Compared to the conventional single camera pseudo-stereo system, which splits the CCD sensor into two halves to capture the stereo views, the proposed system achieves both views using the whole CCD chip and without reducing the spatial resolution. In addition, similarly to the conventional 3D-DIC system, the center of the two views stands in the center of the CCD chip, which minimizes the image distortion relative to the conventional pseudo-stereo system. The two overlapped views in the CCD are separated by the color domain, and the standard 3D-DIC algorithm can be utilized directly to perform the evaluation. The system's principle and experimental setup are described in detail, and multiple tests are performed to validate the system.

An ergonomics prototype of adjustable chin stands aid for visual mechanical inspection at electronic manufacturing-based company in Kuantan, Malaysia

NASA Astrophysics Data System (ADS)

Elias, Nurainaa; Mat Yahya, Nafrizuan

2018-04-01

Chin stands aid is a device designed to reduce fatigue on the chin during the Visual Mechanical Inspection (VMI) task for operators in TT Electronic Sdn Bhd, Kuantan, Malaysia. It is also used to reduce cycle time and also improve employee well-being in terms of comfort. In this project, a 3D model of chin stands aid with an ergonomics approach is created using SOLIDWORKS software. Two different concepts were designed and the best one is chosen based on the Pugh concept selection method, concept screening and also concept scoring. After the selection of concepts is done, a prototype of chin stands aid will be developed and a simulation of the prototype is performed. The simulation has been executed by using Workbench ANSYS software as a tool. Stress analysis, deformation analysis, and fatigue analysis have been done to know the strength and lifespan of the product. The prototype also has been tested to know the functionality and also comfortability for the user to use the chin stands aid.

Simulation Studies of the Effect of Forest Spatial Structure on InSAR Signature

NASA Technical Reports Server (NTRS)

Sun, Guoqing; Liu, Dawei; Ranson, K. Jon; Koetz, Benjamin

2007-01-01

The height of scattering phase retrieved from InSAR data is considered being correlated with the tree height and the spatial structure of the forest stand. Though some researchers have used simple backscattering models to estimate tree height from the height of scattering center, the effect of forest spatial structure on InSAR data is not well understood yet. A three-dimensional coherent radar backscattering model for forest canopies based on realistic three-dimensional scene was used to investigate the effect in this paper. The realistic spatial structure of forest canopies was established either by field measurements (stem map) or through use of forest growth model. Field measurements or a forest growth model parameterized using local environmental parameters provides information of forest species composition and tree sizes in certain growth phases. A fractal tree model (L-system) was used to simulate individual 3- D tree structure of different ages or heights. Trees were positioned in a stand in certain patterns resulting in a 3-D medium of discrete scatterers. The radar coherent backscatter model took the 3-D forest scene as input and simulates the coherent radar backscattering signature. Interferometric SAR images of 3D scenes were simulated and heights of scattering phase centers were estimated from the simulated InSAR data. The effects of tree height, crown cover, crown depth, and the spatial distribution patterns of trees on the scattering phase center were analyzed. The results will be presented in the paper.

Stand basal-area and tree-diameter growth in red spruce-fir forests in Maine, 1960-80

Treesearch

S.J. Zarnoch; D.A. Gansner; D.S. Powell; T.A. Birch; T.A. Birch

1990-01-01

Stand basal-area change and individual surviving red spruce d.b.h. growth from 1960 to 1980 were analyzed for red spruce-fir stands in Maine. Regression modeling was used to relate these measures of growth to stand and tree conditions and to compare growth throughout the period. Results indicate a decline in growth.

Waterfowl foraging in winter-flooded ricefields: Any agronomic benefits for farmers?

PubMed

Brogi, Anne; Pernollet, Claire A; Gauthier-Clerc, Michel; Guillemain, Matthieu

2015-12-01

Winter-flooding of ricefields provides foraging habitat to waterfowl, which in return may bring agronomic benefits to farmers. Our study experimentally tested the effect of mallards (Anas platyrhynchos) on the standing stalks and weed seed bank in the Camargue (France), both of which present major challenges for farmers. Three duck densities were tested: (D1) 5 ducks ha(-1) (historical nocturnal density), (D2) 23 ducks ha(-1) (present nocturnal density), and (D3) 300 ducks ha(-1) (Asian rice-duck farming density). The ducks reduced the stalks significantly: -27 % (D1), -52 % (D2), and -91 % (D3). Conversely, they decreased the number of seeds by only 3 % (D3) and the seed mass by about 21 % (D1 and D3), which was not significant. Besides they had no effect on seed species richness. This study clearly demonstrates that the winter-flooding effect on straw decomposition can be enhanced by waterfowl foraging, hence showing an agronomic benefit from ducks to farmers. However, there was no clear effect in terms of seed bank reduction.

Towards next generation 3D cameras

NASA Astrophysics Data System (ADS)

Gupta, Mohit

2017-03-01

We are in the midst of a 3D revolution. Robots enabled by 3D cameras are beginning to autonomously drive cars, perform surgeries, and manage factories. However, when deployed in the real-world, these cameras face several challenges that prevent them from measuring 3D shape reliably. These challenges include large lighting variations (bright sunlight to dark night), presence of scattering media (fog, body tissue), and optically complex materials (metal, plastic). Due to these factors, 3D imaging is often the bottleneck in widespread adoption of several key robotics technologies. I will talk about our work on developing 3D cameras based on time-of-flight and active triangulation that addresses these long-standing problems. This includes designing `all-weather' cameras that can perform high-speed 3D scanning in harsh outdoor environments, as well as cameras that recover shape of objects with challenging material properties. These cameras are, for the first time, capable of measuring detailed (<100 microns resolution) scans in extremely demanding scenarios with low-cost components. Several of these cameras are making a practical impact in industrial automation, being adopted in robotic inspection and assembly systems.

Comparison of body segmental kinematic characteristics between children with cerebral palsy performing sit-to-stand with and without a walker.

PubMed

Thanapan, Puthamaluk; Prasertsukdee, Saipin; Vachalathiti, Roongtiwa

2013-03-01

The study investigated how the subjects, 18 children with spastic diplegia aged 7-14 years, attained sit-to-stand (STS). The children were divided into two groups and three STS conditions: 1) those who could attain STS independently (I-STS), 2) those who could not attain STS independently (D-STS), and 3) subjects from the D-STS condition who could successfully attain STS with the walker (W-STS). The results showed that I-STS had more mean maximum horizontal location of the upper body and knee than the hip. All body segments of D-STS followed the same model as the I-STS condition, but they moved with less magnitude than I-STS. W-STS presented both pattern and magnitudes relatively similar to I-STS. Furthermore, I-STS showed the highest mean maximum horizontal and vertical velocities of body segments, when compared with the other STS conditions. W-STS performed the mean maximum horizontal and vertical linear velocities of all selected segments close to D-STS did.

Vectorization of a Monte Carlo simulation scheme for nonequilibrium gas dynamics

NASA Technical Reports Server (NTRS)

Boyd, Iain D.

1991-01-01

Significant improvement has been obtained in the numerical performance of a Monte Carlo scheme for the analysis of nonequilibrium gas dynamics through an implementation of the algorithm which takes advantage of vector hardware, as presently demonstrated through application to three different problems. These are (1) a 1D standing-shock wave; (2) the flow of an expanding gas through an axisymmetric nozzle; and (3) the hypersonic flow of Ar gas over a 3D wedge. Problem (3) is illustrative of the greatly increased number of molecules which the simulation may involve, thanks to improved algorithm performance.

Three-Dimensional Printed Graphene Foams.

PubMed

Sha, Junwei; Li, Yilun; Villegas Salvatierra, Rodrigo; Wang, Tuo; Dong, Pei; Ji, Yongsung; Lee, Seoung-Ki; Zhang, Chenhao; Zhang, Jibo; Smith, Robert H; Ajayan, Pulickel M; Lou, Jun; Zhao, Naiqin; Tour, James M

2017-07-25

An automated metal powder three-dimensional (3D) printing method for in situ synthesis of free-standing 3D graphene foams (GFs) was successfully modeled by manually placing a mixture of Ni and sucrose onto a platform and then using a commercial CO 2 laser to convert the Ni/sucrose mixture into 3D GFs. The sucrose acted as the solid carbon source for graphene, and the sintered Ni metal acted as the catalyst and template for graphene growth. This simple and efficient method combines powder metallurgy templating with 3D printing techniques and enables direct in situ 3D printing of GFs with no high-temperature furnace or lengthy growth process required. The 3D printed GFs show high-porosity (∼99.3%), low-density (∼0.015g cm -3 ), high-quality, and multilayered graphene features. The GFs have an electrical conductivity of ∼8.7 S cm -1 , a remarkable storage modulus of ∼11 kPa, and a high damping capacity of ∼0.06. These excellent physical properties of 3D printed GFs indicate potential applications in fields requiring rapid design and manufacturing of 3D carbon materials, for example, energy storage devices, damping materials, and sound absorption.

The modular approach enables a fully ab initio simulation of the contacts between 3D and 2D materials.

PubMed

Fediai, Artem; Ryndyk, Dmitry A; Cuniberti, Gianaurelio

2016-10-05

Up to now, the electrical properties of the contacts between 3D metals and 2D materials have never been computed at a fully ab initio level due to the huge number of atomic orbitals involved in a current path from an electrode to a pristine 2D material. As a result, there are still numerous open questions and controversial theories on the electrical properties of systems with 3D/2D interfaces-for example, the current path and the contact length scalability. Our work provides a first-principles solution to this long-standing problem with the use of the modular approach, a method which rigorously combines a Green function formalism with the density functional theory (DFT) for this particular contact type. The modular approach is a general approach valid for any 3D/2D contact. As an example, we apply it to the most investigated among 3D/2D contacts-metal/graphene contacts-and show its abilities and consistency by comparison with existing experimental data. As it is applicable to any 3D/2D interface, the modular approach allows the engineering of 3D/2D contacts with the pre-defined electrical properties.

Rewritable three-dimensional holographic data storage via optical forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yetisen, Ali K., E-mail: ayetisen@mgh.harvard.edu; Harvard-MIT Division of Health Sciences and Technology, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139; Montelongo, Yunuen

2016-08-08

The development of nanostructures that can be reversibly arranged and assembled into 3D patterns may enable optical tunability. However, current dynamic recording materials such as photorefractive polymers cannot be used to store information permanently while also retaining configurability. Here, we describe the synthesis and optimization of a silver nanoparticle doped poly(2-hydroxyethyl methacrylate-co-methacrylic acid) recording medium for reversibly recording 3D holograms. We theoretically and experimentally demonstrate organizing nanoparticles into 3D assemblies in the recording medium using optical forces produced by the gradients of standing waves. The nanoparticles in the recording medium are organized by multiple nanosecond laser pulses to produce reconfigurablemore » slanted multilayer structures. We demonstrate the capability of producing rewritable optical elements such as multilayer Bragg diffraction gratings, 1D photonic crystals, and 3D multiplexed optical gratings. We also show that 3D virtual holograms can be reversibly recorded. This recording strategy may have applications in reconfigurable optical elements, data storage devices, and dynamic holographic displays.« less

Integration of 3D intraoperative ultrasound for enhanced neuronavigation

NASA Astrophysics Data System (ADS)

Paulsen, Keith D.; Ji, Songbai; Hartov, Alex; Fan, Xiaoyao; Roberts, David W.

2012-03-01

True three-dimensional (3D) volumetric ultrasound (US) acquisitions stand to benefit intraoperative neuronavigation on multiple fronts. While traditional two-dimensional (2D) US and its tracked, hand-swept version have been recognized for many years to advantage significantly image-guided neurosurgery, especially when coregistered with preoperative MR scans, its unregulated and incomplete sampling of the surgical volume of interest have limited certain intraoperative uses of the information that are overcome through direct volume acquisition (i.e., through 2D scan-head transducer arrays). In this paper, we illustrate several of these advantages, including image-based intraoperative registration (and reregistration) and automated, volumetric displacement mapping for intraoperative image updating. These applications of 3D US are enabled by algorithmic advances in US image calibration, and volume rasterization and interpolation for multi-acquisition synthesis that will also be highlighted. We expect to demonstrate that coregistered 3D US is well worth incorporating into the standard neurosurgical navigational environment relative to traditional tracked, hand-swept 2D US.

Progressive 3D shape abstraction via hierarchical CSG tree

NASA Astrophysics Data System (ADS)

Chen, Xingyou; Tang, Jin; Li, Chenglong

2017-06-01

A constructive solid geometry(CSG) tree model is proposed to progressively abstract 3D geometric shape of general object from 2D image. Unlike conventional ones, our method applies to general object without the need for massive CAD models, and represents the object shapes in a coarse-to-fine manner that allows users to view temporal shape representations at any time. It stands in a transitional position between 2D image feature and CAD model, benefits from state-of-the-art object detection approaches and better initializes CAD model for finer fitting, estimates 3D shape and pose parameters of object at different levels according to visual perception objective, in a coarse-to-fine manner. Two main contributions are the application of CSG building up procedure into visual perception, and the ability of extending object estimation result into a more flexible and expressive model than 2D/3D primitive shapes. Experimental results demonstrate the feasibility and effectiveness of the proposed approach.

Tree specific traits vs. stand level characteristics - assessing the source depths of plant water uptake in a mixed forest stand

NASA Astrophysics Data System (ADS)

Seeger, Stefan; Brinkmann, Nadine; Kahmen, Ansgar; Weiler, Markus

2017-04-01

Due to differences in fine root distributions, physiological root characteristics and plant plasticity, the spatial and temporal characteristics of plant water uptake are expected to vary between different tree species. This has implications on the overall water budget of a forest stand as well as on the drought sensitivity of particular trees. A four-year time series of climate data, soil moisture, and stable water isotopes in soil and tree xylem was used to investigate plant water uptake dynamics of four tree species (beech - Fagus sylvatica, spruce - Picea abies, ash - Fraxinus excelsior and maple - Acer pseudoplatanus) in a mixed forest stand. Modeling with a modified version of the soil hydrological model Hydrus-1D allowed us to simulate continuous time series of stable water isotopes in plant water uptake, which were compared to the measured values in tree xylem water and soil water. We found that different estimated species specific fine root distributions and root water uptake parameters lead to very similar simulated water balances and soil water isotope depth profiles for all four species. According to our simulations, differences in evaporative demand (i.e. LAI) had the biggest influence on water uptake and soil water distributions. Comparing the isotopic signatures of simulated root water uptake and measured xylem water, the simulations for beech were most suited to predict the observed signatures of all four species. This indicates that isolated, tree specific parametrized 1-D simulations are not suited to predict actual water uptake of different trees in a mixed stand. Due to overlapping root spaces dominant trees (in our case beeches with an LAI of around 5.5) may influence the soil water storage below accompanying trees (spruces, ashes and maples with LAIs between 1.8 and 3.1) in a degree that their actual water uptake cannot be predicted with 1-D simulations based on their smaller LAI values. Consequently, for a mixed forest stand the interplay of trees with different traits has to be accounted for in order to correctly model plant water uptake of single trees.

Direct observation of gold nanoparticle assemblies with the porin MspA on mica.

PubMed

Basel, Matthew T; Dani, Raj Kumar; Kang, Myungshim; Pavlenok, Mikhail; Chikan, Viktor; Smith, Paul E; Niederweis, Michael; Bossmann, Stefan H

2009-02-24

The octameric porin MspA from Mycobacterium smegmatis is sufficiently stable to form a nonmembrane-supported stand-alone porin on mica surfaces. About 98% of all MspA octamers were found to stand upright on mica, with their periplasmic loop regions bound to the hydrophilic mica surface. Both, small (d = 3.7 nm) and large (d = 17 nm) gold nanoparticles bind to MspA, however, in different positions: small gold nanoparticles bind within the MspA pore, whereas the large gold nanoparticles bind to the upper region of MspA. These experiments demonstrate that gold nanoparticles can be positioned at different, well-defined distances from the underlying surface using the MspA pore as a template. These findings represent a significant step toward the use of electrically insulating stable proteins in combination with metal nanoparticles in nanodevices.

Method for tracking the location of mobile agents using stand-off detection technique

DOEpatents

Schmitt, Randal L [Tijeras, NM; Bender, Susan Fae Ann [Tijeras, NM; Rodacy, Philip J [Albuquerque, NM; Hargis, Jr., Philip J.; Johnson, Mark S [Albuquerque, NM

2006-12-26

A method for tracking the movement and position of mobile agents using light detection and ranging (LIDAR) as a stand-off optical detection technique. The positions of the agents are tracked by analyzing the time-history of a series of optical measurements made over the field of view of the optical system. This provides a (time+3-D) or (time+2-D) mapping of the location of the mobile agents. Repeated pulses of a laser beam impinge on a mobile agent, such as a bee, and are backscattered from the agent into a LIDAR detection system. Alternatively, the incident laser pulses excite fluorescence or phosphorescence from the agent, which is detected using a LIDAR system. Analysis of the spatial location of signals from the agents produced by repeated pulses generates a multidimensional map of agent location.

Optically-free-standing InGaN microdisks with metallic reflectors

NASA Astrophysics Data System (ADS)

Zhang, Xuhui; To, Chap Hang; Choi, Hoi Wai

2017-01-01

The optical properties of free-standing thin-film microdisks with NiAg metallic reflectors are compared with those with an indium tin oxide (ITO) interfacial layer. The microdisks have been fabricated by a combination of microsphere lithography and laser lift-off processes. Optical-pumped lasing from the microdisk with NiAg reflector has been observed, with reduced threshold and higher quality factor compared those with ITO layers, attributed to improved optical confinement due to the reflectivity of the Ag coating. The results are supported by three-dimensional (3D) finite-difference-time-domain (FDTD) simulations.

KSC-06pd1527

NASA Image and Video Library

2006-07-07

KENNEDY SPACE CENTER, FLA. - At Astrotech Space Operations in Titusville, Fla., workers move one of the covered STEREO observatories on its portable stand . It is being transferred to the Hazardous Processing Facility for fueling. STEREO, which stands for Solar Terrestrial Relations Observatory, consists of two spacecraft whose mission is to take measurements of the sun and solar wind in 3-D, for the first time. This new view will improve our understanding of space weather and its impact on the Earth. Preparations are under way for a liftoff aboard a Delta rocket no earlier than Aug. 1. Photo credit: NASA/George Shelton

Organomimetic clusters: Precision in 3D

NASA Astrophysics Data System (ADS)

Majewski, Marek B.; Howarth, Ashlee J.; Farha, Omar K.

2017-04-01

Biomimetic molecules that can be easily tailored offer numerous opportunities. Now, boron-based clusters have been shown to be excellent biomimetics. The ease with which the cluster surfaces can be modified stands to change how chemists might go about preparing materials for imaging, drug delivery and other applications.

A randomized, double-blind, placebo-controlled clinical trial on the treatment of vitamin D insufficiency in postmenopausal women

PubMed Central

Hansen, Karen E.; Johnson, R. Erin; Chambers, Kaitlin R.; Johnson, Michael G.; Lemon, Christina C.; Thuy Vo, Tien Nguyen; Marvdashti, Sheeva

2015-01-01

Importance Experts debate optimal 25(OH)D levels for musculoskeletal health. Objective To compare effects of placebo, low-dose and high-dose vitamin D on one-year changes in total fractional calcium absorption, bone mineral density, Timed-Up-and-Go and 5-sit-to-stand tests and muscle mass in postmenopausal women with vitamin D insufficiency. Design Randomized, double-blind, placebo-controlled, clinical trial conducted from May 2010 to August 2014. Setting Single-center trial conducted in Madison, Wisconsin. Participants 230 postmenopausal women ≤75 years old with baseline 25(OH)D levels 14-27 ng/mL and no osteoporosis. Intervention Three arms included daily white and twice monthly yellow placebo (n=76), daily 800 IU vitamin D3 and twice monthly yellow placebo (n=76), and daily white placebo and twice monthly 50,000 IU vitamin D3 (n=79). The high-dose vitamin D regimen achieved and maintained 25(OH)D levels ≥30 ng/mL. Main Outcome Measures One year change in total fractional calcium absorption using two stable isotopes, bone mineral density and muscle mass using dual energy x-ray absorptiometry, Timed-Up-and-Go and 5-Sit-to-Stand tests, functional status (Health Assessment Questionnaire) and physical activity (Physical Activity Scale for the Elderly), with Benjamini-Hochberg correction of p-values to control the false discovery rate. Results After controlling for baseline absorption, calcium absorption increased 1% (10 mg/day) in the high-dose arm, but decreased by 2% in low-dose (p=0.005 vs. high-dose) and by 1.3% placebo (p=0.03 vs. high-dose) arms. We found no between-arm changes in spine, mean total hip, mean femoral neck or total body bone mineral density, trabecular bone score, muscle mass, 5-sit-to-stand or Timed-Up-and-Go test scores. Likewise, we found no between-arm differences for numbers of falls, number of fallers, physical activity or functional status. Conclusion and Relevance High-dose vitamin D therapy increased calcium absorption, but the effect was small and did not translate into beneficial effects on bone mineral density, muscle function, muscle mass or falls. We found no data to support experts’ recommendations to maintain serum 25(OH)D levels ≥30 ng/mL in postmenopausal women. Instead, we found that low and high-dose vitamin D were equivalent to placebo, in their effects on bone and muscle outcomes in this cohort of postmenopausal women with 25(OH)D levels <30 ng/mL. ClinicalTrials.gov.Identifier:NCT00933244 PMID:26237520

All-in-One Cellulose Nanocrystals for 3D Printing of Nanocomposite Hydrogels.

PubMed

Wang, Jieping; Chiappone, Annalisa; Roppolo, Ignazio; Shao, Feng; Fantino, Erika; Lorusso, Massimo; Rentsch, Daniel; Dietliker, Kurt; Pirri, Candido Fabrizio; Grützmacher, Hansjörg

2018-02-23

Cellulose nanocrystals (CNCs) with >2000 photoactive groups on each can act as highly efficient initiators for radical polymerizations, cross-linkers, as well as covalently embedded nanofillers for nanocomposite hydrogels. This is achieved by a simple and reliable method for surface modification of CNCs with a photoactive bis(acyl)phosphane oxide derivative. Shape-persistent and free-standing 3D structured objects were printed with a mono-functional methacrylate, showing a superior swelling capacity and improved mechanical properties. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Single DMD time-multiplexed 64-views autostereoscopic 3D display

NASA Astrophysics Data System (ADS)

Loreti, Luigi

2013-03-01

Based on previous prototype of the Real time 3D holographic display developed last year, we developed a new concept of auto-stereoscopic multiview display (64 views), wide angle (90°) 3D full color display. The display is based on a RGB laser light source illuminating a DMD (Discovery 4100 0,7") at 24.000 fps, an image deflection system made with an AOD (Acoustic Optic Deflector) driven by a piezo-electric transducer generating a variable standing acoustic wave on the crystal that acts as a phase grating. The DMD projects in fast sequence 64 point of view of the image on the crystal cube. Depending on the frequency of the standing wave, the input picture sent by the DMD is deflected in different angle of view. An holographic screen at a proper distance diffuse the rays in vertical direction (60°) and horizontally select (1°) only the rays directed to the observer. A telescope optical system will enlarge the image to the right dimension. A VHDL firmware to render in real-time (16 ms) 64 views (16 bit 4:2:2) of a CAD model (obj, dxf or 3Ds) and depth-map encoded video images was developed into the resident Virtex5 FPGA of the Discovery 4100 SDK, thus eliminating the needs of image transfer and high speed links

Design and Use of a 3D Prosthetic Leg in a Red-lored Amazon Parrot ( Amazona autumnalis).

PubMed

Galicia, Cecilia; Hernandez Urraca, Vanessa; Del Castillo, Luis; Mvz, Jaime Samour

2018-06-01

A three-dimensional (3D) prosthesis was designed and built for a red-lored Amazon parrot ( Amazona autumnalis) with a pre-existing amputation of the distal left leg at the tibiotarsal-tarsometatarsal joint and injuries to the right leg caused by cage companion aggression. The prosthesis consisted of a straight main imprint, with a round element at both ends to provide stability, and a bridge connecting this to a socket without a bottom where the stump could be accommodated and held securely with self-adhesive bandaging. Over a 4-month period, 3 different 3D prosthetic models were made and evaluated. The first model was fitted, but the parrot would only use the tip of the main imprint to stand and walk. The second model was designed with a semicircular imprint with only 1 round element at the cranial end, a different bridge to accommodate the change to the main imprint, and the same socket. With these changes, the parrot was able to place the imprint of the prosthesis on the floor to stand and move freely around its enclosure. To accommodate morphologic changes on the stump, a third model was created consisting of the same imprint and bridge, but the socket was cut vertically all the way on one side to allow distention on its diameter and provide a long-lasting fit to the stump over time.

Associations of herd- and cow-level factors, cow lying behavior, and risk of elevated somatic cell count in free-stall housed lactating dairy cows.

PubMed

Watters, M E Alexandrea; Meijer, Karin M A; Barkema, Herman W; Leslie, Kenneth E; von Keyserlingk, Marina A G; Devries, Trevor J

2013-09-01

Recent evidence suggests that the risk of intramammary infection in dairy cows is related to lying patterns. The objectives of this study were to quantify the standing and lying behavior of dairy cows milked 3×/d, determine the cow- and herd-level factors associated with these behaviors, and relate these findings to the risk of an elevated somatic cell count (SCC). Five commercial free-stall dairy herds in Eastern Ontario, milking 3×/d, were enrolled in a longitudinal study. Forty Holstein-Friesian cows/herd were randomly selected as focal animals based on days in milk (<200 d) and SCC (<100,000 cells/mL). Farms were followed for 4, 5-week periods. Individual-cow SCC was recorded at the beginning of each period and end of the final period. Elevated SCC (eSCC) was used as an indicator of subclinical mastitis. A new incident eSCC was defined as an individual cow that started the period with a SCC <100,000 cells/mL but whose next SCC exceeded 200,000 cells/mL. Lying behavior was recorded 5d after each milk sampling using data loggers. For these 5d, individual milking times and feeding times were also recorded. On d1 of each recording period 2 trained observers scored focal cows for hygiene and lameness. Throughout the course of the study, cows averaged 11.2h/d of lying time, split into 8.6 lying bouts/d that were on average 84.6 min in length. Later lactation cows had longer daily lying times that were split into fewer lying bouts of longer duration than cows earlier in lactation. Lame cows had longer daily lying times and lying bout durations than non-lame cows. Cows with greater milk yield had lower lying times than lower producing cows. Average post-milking standing time across the study herds was 103 min. Manipulation of feed (feed delivery or push-up) by the stockperson, in the hour before milking or shortly thereafter, resulted in the longest post-milking standing times. Over the study period, 48 new eSCC were detected, resulting in a mean herd incidence rate of 0.91 eSCC/cow-year at risk for all study herds. A non-linear relationship between post-milking standing time and eSCC incidence was found; compared to those cows that lie down <90 min after milking, cows that lie down for the first time >90 min after milking had a lower risk of acquiring a new eSCC. The risk of experiencing an eSCC was also increased in multiparous cows, and in those cows with a higher SCC at the beginning of the study. These results indicate that management practices that promote post-milking standing time, such as the manipulation of feed delivery around milking times, should be encouraged to reduce the risk of cows experiencing new eSCC. Copyright © 2013 Elsevier B.V. All rights reserved.

Diet of southern toads (Bufo terrestris) in loblolly pine (Pinus taeda) stands subject to coarse woody debris manipulations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moseley, Kurtis R.; Steven B. Castleberry; James L. Hanula

2005-04-01

ABSTRACT In the southeastern United States, coarse woody debris (CWD) typically harbors high densities of invertebrates. However, its importance as a foraging substrate for southeastern amphibians is relatively unknown. We examined effects of CWD manipulations on diet composition of southern toads (Bufo terrestris) in upland loblolly pine (Pinus taeda) stands in the Coastal Plain of South Carolina. Twelve 9.3-ha plots were assigned one of the following treatments: removal- all CWD _10 cm in diameter and _60 cm long removed; downed- five-fold increase in volume of down CWD; and unmanipulated control stands. We collected southern toads _4 cm snout-vent length (SVL)more » during 14 d sampling periods in June and October 2002, June 2003 and during a 28 d sampling period in April 2003. We collected 80, 36 and 35 southern toads in control, downed and removal treatments, respectively. We found no difference in relative abundance or frequency of invertebrate groups consumed among treatments (P.0.05). Average body weight (g), SVL (cm) and stomach content weight (g wet) of individuals also were similar among treatments (P . 0.05). The role of CWD as a foraging substrate for southern toads in loblolly pine stands of the southeastern Coastal Plain may be negligible, at least in the early stages of decay.« less

Estimating decay in 40- to 90-year-old grand fir stands in the Clearwater region of northern Idaho.

Treesearch

Gregory M. Filip; John W. Schwandt; Susan K. Hagle

1990-01-01

The fir decay equation for Oregon and Washington was used to predict stem decay in 12 grand fir (Abies grandis (Dougl. ex D. Don) Lindl.) stands in the Clearwater region of northern Idaho. These 12 stands represented a range in geographic and stand characteristic variation. All 12 observed decay percentages were within their associated 95-percent...

Reshaping drug development using 3D printing.

PubMed

Awad, Atheer; Trenfield, Sarah J; Goyanes, Alvaro; Gaisford, Simon; Basit, Abdul W

2018-05-24

The pharmaceutical industry stands on the brink of a revolution, calling for the recognition and embracement of novel techniques. 3D printing (3DP) is forecast to reshape the way in which drugs are designed, manufactured, and used. Although a clear trend towards personalised fabrication is perceived, here we accentuate the merits and shortcomings of each technology, providing insights into aspects such as the efficiency of production, global supply, and logistics. Contemporary opportunities for 3DP in drug discovery and pharmaceutical development and manufacturing are unveiled, offering a forward-looking view on its potential uses as a digitised tool for personalised dispensing of drugs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization of Mycobacterium smegmatis PolD2 and PolD1 as RNA/DNA polymerases homologous to the POL domain of bacterial DNA ligase D

PubMed Central

Zhu, Hui; Bhattarai, Hitesh; Yan, Han-Guang; Shuman, Stewart; Glickman, Michael S.

2013-01-01

Mycobacteria exploit nonhomologous end-joining (NHEJ) to repair DNA double-strand breaks. The core NHEJ machinery comprises the homodimeric DNA end-binding protein Ku and DNA ligase D (LigD), a modular enzyme composed of a C-terminal ATP-dependent ligase domain (LIG), a central 3’-phosphoesterase domain (PE), and an N-terminal polymerase domain (POL). LigD POL is proficient at adding templated and nontemplated deoxynucleotide and ribonucleotides to DNA ends in vitro and is the catalyst in vivo of unfaithful NHEJ events involving nontemplated single-nucleotide additions to blunt DSB ends. Here, we identify two mycobacterial proteins, PolD1 and PolD2, as stand-alone homologs of the LigD POL domain. Biochemical characterization of PolD1 and PolD2 shows that they resemble LigD POL in their monomeric quaternary structures, their ability to add templated and nontemplated nucleotides to primer-templates and blunt ends, and their preference for rNTPs versus dNTPs. Deletion of polD1, polD2, or both, in an M. smegmatis strain carrying an inactivating mutation in LigD POL failed to reveal a role for PolD1 or PolD2 in templated nucleotide additions during NHEJ of 5’-overhang DSBs or in clastogen resistance. Whereas our results document the existence and characteristics of new stand-alone members of the LigD POL family of RNA/DNA polymerases, they imply that other polymerases can perform fill-in synthesis during mycobacterial NHEJ. PMID:23198659

SU-E-T-04: 3D Printed Patient-Specific Surface Mould Applicators for Brachytherapy Treatment of Superficial Lesions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cumming, I; Lasso, A; Rankin, A

2014-06-01

Purpose: Evaluate the feasibility of constructing 3D-printed patient-specific surface mould applicators for HDR brachytherapy treatment of superficial lesions. Methods: We propose using computer-aided design software to create 3D printed surface mould applicators for brachytherapy. A mould generation module was developed in the open-source 3D Slicer ( http://www.slicer.org ) medical image analysis platform. The system extracts the skin surface from CT images, and generates smooth catheter paths over the region of interest based on user-defined start and end points at a specified stand-off distance from the skin surface. The catheter paths are radially extended to create catheter channels that are sufficientlymore » wide to ensure smooth insertion of catheters for a safe source travel. An outer mould surface is generated to encompass the channels. The mould is also equipped with fiducial markers to ensure its reproducible placement. A surface mould applicator with eight parallel catheter channels of 4mm diameters was fabricated for the nose region of a head phantom; flexible plastic catheters of 2mm diameter were threaded through these channels maintaining 10mm catheter separations and a 5mm stand-off distance from the skin surface. The apparatus yielded 3mm thickness of mould material between channels and the skin. The mould design was exported as a stereolithography file to a Dimension SST1200es 3D printer and printed using ABS Plus plastic material. Results: The applicator closely matched its design and was found to be sufficiently rigid without deformation during repeated application on the head phantom. Catheters were easily threaded into channels carved along catheter paths. Further tests are required to evaluate feasibility of channel diameters smaller than 4mm. Conclusion: Construction of 3D-printed mould applicators show promise for use in patient specific brachytherapy of superficial lesions. Further evaluation of 3D printing techniques and materials is required for constructing sufficiently thin, rigid and durable surface moulds suitable for clinical deployment.« less

Surface forcing of non-stand-replacing fires in Siberian larch forests

NASA Astrophysics Data System (ADS)

Chen, Dong; Loboda, Tatiana V.

2018-04-01

Wildfires are the dominant disturbance agent in the Siberian larch forests. Extensive low- to mediate-intensity non-stand-replacing fires are a notable property of fire regime in these forests. Recent large scale studies of these fires have focused mostly on their impacts on carbon budget; however, their potential impacts on energy budget through post-fire albedo changes have not been considered. This study quantifies the post-fire surface forcing for Siberian larch forests that experienced non-stand-replacing fires between 2001 and 2012 using the full record of MODIS MCD43A3 albedo product and a burned area product developed specifically for the Russian forests. Despite a large variability, the mean effect of non-stand-replacing fires imposed through albedo is a negative forcing which lasts for at least 14 years. However, the magnitude of the forcing is much smaller than that imposed by stand-replacing fires, highlighting the importance of differentiating between the two fire types in the studies involving the fire impacts in the region. The results of this study also show that MODIS-based summer differenced normalized burn ratio (dNBR) provides a reliable metric for differentiating non-stand-replacing from stand-replacing fires with an overall accuracy of 88%, which is of considerable importance for future work on modeling post-fire energy budget and carbon budget in the region.

13. Photographic copy of site plan displaying Test Stand 'C' ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Photographic copy of site plan displaying Test Stand 'C' (4217/E-18), Test Stand 'D' (4223/E-24), and Control and Recording Center (4221/E-22) with ancillary structures, and connecting roads and services. California Institute of Technology, Jet Propulsion Laboratory, Facilities Engineering and Construction Office 'Repairs to Test Stand 'C,' Edwards Test Station, Legend & Site Plan M-1,' drawing no. ESP/115, August 14, 1987. - Jet Propulsion Laboratory Edwards Facility, Test Stand C, Edwards Air Force Base, Boron, Kern County, CA

Objectively Measured Daily Physical Activity and Postural Changes as Related to Positive and Negative Affect Using Ambulatory Monitoring Assessments.

PubMed

Aggio, Daniel; Wallace, Karen; Boreham, Nicola; Shankar, Aparna; Steptoe, Andrew; Hamer, Mark

2017-09-01

The aim of the study was to determine whether objectively measured daily physical activity and posture of sitting, standing, and sit-to-stand transitions are associated with daily assessments of affect. Participants (N = 51, 49% female) wore ActivPal accelerometers for 24 h/d for seven consecutive days. Time spent sitting, standing, and being physically active and sit-to-stand transitions were derived for each day. Participants also completed a mood inventory each evening. Multilevel models examined within- and between-person associations of daily physical activity with positive and negative affect, adjusting for age, sex, body mass index, education, and sleep duration. Within-person associations showed that a 1-hour increase in daily physical activity was associated with a decrease in negative affect over the same day (B = -0.11, 95% confidence interval [CI], -0.21 to -0.01). Between-person associations indicated a borderline significant association between higher average daily physical activity levels and higher positive affect (B = 1.85, 95% CI = -0.25 to 3.94). There were no between- or within-person associations between sitting, standing, and sit-to-stand transitions with affect. Promoting physical activity may be a potential intervention strategy to acutely suppress negative affective states.

10 GHz Standing-Wave Coplanar Stripline on LiNbO3 Crystal for Radio to Optical-Wave Conversion

NASA Astrophysics Data System (ADS)

Darwis, F.; Wijayanto, Y. N.; Setiawan, A.; Mahmudin, D.; Rahman, A. N.; Daud, P.

2018-04-01

Recently, X-band radar systems are used widely for surveillance and navigation applications. Especially in archipelago or maritime country, the surveillance/navigation radar systems are required to monitoring critical areas and managing marine traffic. Accurate detection and fast analysis should be improved furthermore to provide security and safety condition. Therefore, several radar systems should be installed in many places to coverage the critical areas within radar networks. The radar network can be connected using optical fibers since it has extremely low propagation loss with optical-wave to carry-out the radar-wave. One important component in the scenario is a radio to optical-wave conversion component. In this paper, we report a 10 GHz radio to optical-wave conversion component using standing-wave coplanar stripline (CPS) on LiNbO3 optical crystal as the substrate. The standing-wave CPS electrodes with narrow slot are arranged in an array structure. An optical waveguide is located close to the narrow slot. The CPS electrodes were analysed using electromagnetic analysis software for 10 GHz operational frequency. Responses for slot width and electrode length variation are reported. As results, return loss of -14.580 dB and -19.517 dB are obtained for single and array CPS electrodes respectively. Optimization of the designed radio to optical-wave conversion devices was also done.

80-MHz intravascular ultrasound transducer using PMN-PT free-standing film.

PubMed

Li, Xiang; Wu, Wei; Chung, Youngsoo; Shih, Wan Y; Shih, Wei-Heng; Zhou, Qifa; Shung, K Kirk

2011-11-01

[Pb(Mg(1/3)Nb(2/3))O(3)](0.63)[PbTiO(3)](0.37) (PMN-PT) free-standing film of comparable piezoelectric properties to bulk material with thickness of 30 μm has been fabricated using a modified precursor coating approach. At 1 kHz, the dielectric permittivity and loss were 4364 and 0.033, respectively. The remnant polarization and coercive field were 28 μC/cm(2) and 18.43 kV/cm. The electromechanical coupling coefficient k(t) was measured to be 0.55, which was close to that of bulk PMN-PT single-crystal material. Based on this film, high-frequency (82 MHz) miniature ultrasonic transducers were fabricated with 65% bandwidth and 23 dB insertion loss. Axial and lateral resolutions were determined to be as high as 35 and 176 μm. In vitro intravascular imaging on healthy rabbit aorta was performed using the thin film transducers. In comparison with a 35-MHz IVUS transducer, the 80-MHz transducer showed superior resolution and contrast with satisfactory penetration depth. The imaging results suggest that PMN-PT free-standing thin film technology is a feasible and efficient way to fabricate very-high-frequency ultrasonic transducers.

7 CFR 82.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... means “Application for Clingstone Peach Tree Removal Program.” (d) Calendar year means the 12-month... industry in California. (f) Diversion means the removal of clingstone peach trees after approval of... clingstone peach trees are no longer standing and capable of producing a crop, and the roots of the trees...

Learning about Lasers

ERIC Educational Resources Information Center

Roberts, Larry

2011-01-01

The word laser is an acronym. It stands for Light Amplification by Stimulated Emission of Radiation. Lasers, invented in 1958, are used to cut and fuse materials, accurately survey long distances, communicate across fiber-optic phone lines, produce 3D pictures, make special effects, help navigation, and read bar codes for cash registers. A laser…

Sawtimber by Prescription - The Sudden Sawlog Story Through Age 33

Treesearch

J.D. Burton

1982-01-01

Presents total and net yield, standing volume, volume harvested, and natural mortality, in cubic feet i.b. to a 3-inch top d.i.b., and in board feet Int. ¼ to an 8-inch and to a 6-inch top, together with dbh distribution at various ages.

1. BUILDING 8814, NORTH FRONT AND WEST SIDE. BUILDING 8832, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. BUILDING 8814, NORTH FRONT AND WEST SIDE. BUILDING 8832, TEST STAND 1-E, IN LEFT DISTANCE. Looking southeast. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Observation Bunker 1-D-3, Test Area 1-125, northwest end of Altair Boulevard, Boron, Kern County, CA

Air Force Journal of Logistics. Volume 30, Number 3, Fall 2006

DTIC Science & Technology

2006-01-01

recognized that solutions will require of what works and what does not.130 Much as the Gossamer scientific breakthroughs and truly revolutionary...developments. Albatross and Spaceship One were inspired by standing prizes, Within this context, nanoscience and nanotechnology present the DoD may find its

SABERS. Stand-Alone ADIC Binary Exploitation Resources System. Volume III.

DTIC Science & Technology

1981-09-01

REFERENCE MANUAL Data Base Example TRIZ ?age . (Initial State) 2 0 513 Figure D-2C The DBM generates and maintains several trie pages in the course of...5 5 5 1 582 1 26 PROCSS _ 3 TRIZ _ _ I _ _ _ I .... _ _--_ _ _ _ _ Ii_ _ _ _ _ _ _ _ _ ,,,,___ _ _ _ _ __ _ . . . 1.1 _ _ _ _ Page 2 58 0 . _2562. 0

Active remote sensing.

Treesearch

Hans-Erik Andersen; Stephen E. Reutebuch; Robert J. McGaughey

2006-01-01

The development of remote sensing technologies increases the potential to support more precise, efficient, and ecologically-sensitive approaches to forest resource management. One of the primary requirements of precision forest management is accurate and detailed 3D spatial data relating to the type and condition of forest stands and characteristics of the underlying...

Credit WCT. Photographic copy of photograph, oxidizer and fuel tank ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, oxidizer and fuel tank assembly for engine tests being raised by crane for permanent installation in Test Stand "D" tower. Each tank held 170 gallons of propellants. (JPL negative 384-2029-B, 7 August 1959) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Preparation of Three-Dimensional Graphene Foams Using Powder Metallurgy Templates.

PubMed

Sha, Junwei; Gao, Caitian; Lee, Seoung-Ki; Li, Yilun; Zhao, Naiqin; Tour, James M

2016-01-26

A simple and scalable method which combines traditional powder metallurgy and chemical vapor deposition is developed for the synthesis of mesoporous free-standing 3D graphene foams. The powder metallurgy templates for 3D graphene foams (PMT-GFs) consist of particle-like carbon shells which are connected by multilayered graphene that shows high specific surface area (1080 m(2) g(-1)), good crystallization, good electrical conductivity (13.8 S cm(-1)), and a mechanically robust structure. The PMT-GFs did not break under direct flushing with DI water, and they were able to recover after being compressed. These properties indicate promising applications of PMT-GFs for fields requiring 3D carbon frameworks such as in energy-based electrodes and mechanical dampening.

Development of NSSS Thermal-Hydraulic Model for KNPEC-2 Simulator Using the Best-Estimate Code RETRAN-3D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Kyung-Doo; Jeong, Jae-Jun; Lee, Seung-Wook

The Nuclear Steam Supply System (NSSS) thermal-hydraulic model adopted in the Korea Nuclear Plant Education Center (KNPEC)-2 simulator was provided in the early 1980s. The reference plant for KNPEC-2 is the Yong Gwang Nuclear Unit 1, which is a Westinghouse-type 3-loop, 950 MW(electric) pressurized water reactor. Because of the limited computational capability at that time, it uses overly simplified physical models and assumptions for a real-time simulation of NSSS thermal-hydraulic transients. This may entail inaccurate results and thus, the possibility of so-called ''negative training,'' especially for complicated two-phase flows in the reactor coolant system. To resolve the problem, we developedmore » a realistic NSSS thermal-hydraulic program (named ARTS code) based on the best-estimate code RETRAN-3D. The systematic assessment of ARTS has been conducted by both a stand-alone test and an integrated test in the simulator environment. The non-integrated stand-alone test (NIST) results were reasonable in terms of accuracy, real-time simulation capability, and robustness. After successful completion of the NIST, ARTS was integrated with a 3-D reactor kinetics model and other system models. The site acceptance test (SAT) has been completed successively and confirmed to comply with the ANSI/ANS-3.5-1998 simulator software performance criteria. This paper presents our efforts for the ARTS development and some test results of the NIST and SAT.« less

One-Step Solvent Evaporation-Assisted 3D Printing of Piezoelectric PVDF Nanocomposite Structures.

PubMed

Bodkhe, Sampada; Turcot, Gabrielle; Gosselin, Frederick P; Therriault, Daniel

2017-06-21

Development of a 3D printable material system possessing inherent piezoelectric properties to fabricate integrable sensors in a single-step printing process without poling is of importance to the creation of a wide variety of smart structures. Here, we study the effect of addition of barium titanate nanoparticles in nucleating piezoelectric β-polymorph in 3D printable polyvinylidene fluoride (PVDF) and fabrication of the layer-by-layer and self-supporting piezoelectric structures on a micro- to millimeter scale by solvent evaporation-assisted 3D printing at room temperature. The nanocomposite formulation obtained after a comprehensive investigation of composition and processing techniques possesses a piezoelectric coefficient, d 31 , of 18 pC N -1 , which is comparable to that of typical poled and stretched commercial PVDF film sensors. A 3D contact sensor that generates up to 4 V upon gentle finger taps demonstrates the efficacy of the fabrication technique. Our one-step 3D printing of piezoelectric nanocomposites can form ready-to-use, complex-shaped, flexible, and lightweight piezoelectric devices. When combined with other 3D printable materials, they could serve as stand-alone or embedded sensors in aerospace, biomedicine, and robotic applications.

Pelvic morphology, body posture and standing balance characteristics of adolescent able-bodied and idiopathic scoliosis girls.

PubMed

Stylianides, Georgios A; Dalleau, Georges; Begon, Mickaël; Rivard, Charles-Hilaire; Allard, Paul

2013-01-01

The purpose of this study was to determine how pelvic morphology, body posture, and standing balance variables of scoliotic girls differ from those of able-bodied girls, and to classify neuro-biomechanical variables in terms of a lower number of unobserved variables. Twenty-eight scoliotic and twenty-five non-scoliotic able-bodied girls participated in this study. 3D coordinates of ten anatomic body landmarks were used to describe pelvic morphology and trunk posture using a Flock of Birds system. Standing balance was measured using a force plate to identify the center of pressure (COP), and its anteroposterior (AP) and mediolateral (ML) displacements. A multivariate analysis of variance (MANOVA) was performed to determine differences between the two groups. A factor analysis was used to identify factors that best describe both groups. Statistical differences were identified between the groups for each of the parameter types. While spatial orientation of the pelvis was similar in both groups, five of the eight trunk postural variables of the scoliotic group were significantly different that the able-bodied group. Also, five out of the seven standing balance variables were higher in the scoliotic girls. Approximately 60% of the variation is supported by 4 factors that can be associated with a set of variables; standing balance variables (factor 1), body posture variables (factor 2), and pelvic morphology variables (factors 3 and 4). Pelvic distortion, body posture asymmetry, and standing imbalance are more pronounced in scoliotic girls, when compared to able-bodied girls. These findings may be beneficial when addressing balance and ankle proprioception exercises for the scoliotic population.

220GHz wideband 3D imaging radar for concealed object detection technology development and phenomenology studies

NASA Astrophysics Data System (ADS)

Robertson, Duncan A.; Macfarlane, David G.; Bryllert, Tomas

2016-05-01

We present a 220 GHz 3D imaging `Pathfinder' radar developed within the EU FP7 project CONSORTIS (Concealed Object Stand-Off Real-Time Imaging for Security) which has been built to address two objectives: (i) to de-risk the radar hardware development and (ii) to enable the collection of phenomenology data with ~1 cm3 volumetric resolution. The radar combines a DDS-based chirp generator and self-mixing multiplier technology to achieve a 30 GHz bandwidth chirp with such high linearity that the raw point response is close to ideal and only requires minor nonlinearity compensation. The single transceiver is focused with a 30 cm lens mounted on a gimbal to acquire 3D volumetric images of static test targets and materials.

A New Approach to Improve Cognition, Muscle Strength, and Postural Balance in Community-Dwelling Elderly with a 3-D Virtual Reality Kayak Program.

PubMed

Park, Junhyuck; Yim, JongEun

2016-01-01

Aging is usually accompanied with deterioration of physical abilities, such as muscular strength, sensory sensitivity, and functional capacity. Recently, intervention methods with virtual reality have been introduced, providing an enjoyable therapy for elderly. The aim of this study was to investigate whether a 3-D virtual reality kayak program could improve the cognitive function, muscle strength, and balance of community-dwelling elderly. Importantly, kayaking involves most of the upper body musculature and needs the balance control. Seventy-two participants were randomly allocated into the kayak program group (n = 36) and the control group (n = 36). The two groups were well matched with respect to general characteristics at baseline. The participants in both groups performed a conventional exercise program for 30 min, and then the 3-D virtual reality kayak program was performed in the kayak program group for 20 min, two times a week for 6 weeks. Cognitive function was measured using the Montreal Cognitive Assessment. Muscle strength was measured using the arm curl and handgrip strength tests. Standing and sitting balance was measured using the Good Balance system. The post-test was performed in the same manner as the pre-test; the overall outcomes such as cognitive function (p < 0.05), muscle strength (p < 0.05), and balance (standing and sitting balance, p < 0.05) were significantly improved in kayak program group compared to the control group. We propose that the 3-D virtual reality kayak program is a promising intervention method for improving the cognitive function, muscle strength, and balance of elderly.

Credit BG. Looking southeast at Test Stand "D" (Building 4223/E24). ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. Looking southeast at Test Stand "D" (Building 4223/E-24). Left foreground contains six high-pressure nitrogen tanks which supplied nitrogen for operation of propellant valves. Several tanks for other substances have been removed from the base of the tower as part of decontamination and dismantling program. The vertical vacuum test cell can be seen in the tower behind the western sunscreen. At the top of the tower in the northeast corner is the interstage condenser used in the series of vacuum ejectors; at the top of the condenser is one of two Z-stage ejectors used to evacuate the condenser. The hoist beam for lifting/lowering rocket engines can be clearly seen projecting to the west over the pavement. In the distance on the right are Clayton water-tube steam generators from Building 4280/E-81, and the towers for Test Stand "C" and its scrubber-condenser - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Novel 3D geometry and models of the lower regions of large trees for use in carbon accounting of primary forests

PubMed Central

Dean, Christopher; Kirkpatrick, Jamie B; Osborn, Jon; Doyle, Richard B; Fitzgerald, Nicholas B; Roxburgh, Stephen H

2018-01-01

Abstract There is high uncertainty in the contribution of land-use change to anthropogenic climate change, especially pertaining to below-ground carbon loss resulting from conversion of primary-to-secondary forest. Soil organic carbon (SOC) and coarse roots are concentrated close to tree trunks, a region usually unmeasured during soil carbon sampling. Soil carbon estimates and their variation with land-use change have not been correspondingly adjusted. Our aim was to deduce allometric equations that will allow improvement of SOC estimates and tree trunk carbon estimates, for primary forest stands that include large trees in rugged terrain. Terrestrial digital photography, photogrammetry and GIS software were used to produce 3D models of the buttresses, roots and humus mounds of large trees in primary forests dominated by Eucalyptus regnans in Tasmania. Models of 29, in situ eucalypts were made and analysed. 3D models of example eucalypt roots, logging debris, rainforest tree species, fallen trees, branches, root and trunk slices, and soil profiles were also derived. Measurements in 2D, from earlier work, of three buttress ‘logs’ were added to the data set. The 3D models had high spatial resolution. The modelling allowed checking and correction of field measurements. Tree anatomical detail was formulated, such as buttress shape, humus volume, root volume in the under-sampled zone and trunk hollow area. The allometric relationships developed link diameter at breast height and ground slope, to SOC and tree trunk carbon, the latter including a correction for senescence. These formulae can be applied to stand-level carbon accounting. The formulae allow the typically measured, inter-tree SOC to be corrected for not sampling near large trees. The 3D models developed are irreplaceable, being for increasingly rare, large trees, and they could be useful to other scientific endeavours. PMID:29593855

Novel 3D geometry and models of the lower regions of large trees for use in carbon accounting of primary forests.

PubMed

Dean, Christopher; Kirkpatrick, Jamie B; Osborn, Jon; Doyle, Richard B; Fitzgerald, Nicholas B; Roxburgh, Stephen H

2018-03-01

There is high uncertainty in the contribution of land-use change to anthropogenic climate change, especially pertaining to below-ground carbon loss resulting from conversion of primary-to-secondary forest. Soil organic carbon (SOC) and coarse roots are concentrated close to tree trunks, a region usually unmeasured during soil carbon sampling. Soil carbon estimates and their variation with land-use change have not been correspondingly adjusted. Our aim was to deduce allometric equations that will allow improvement of SOC estimates and tree trunk carbon estimates, for primary forest stands that include large trees in rugged terrain. Terrestrial digital photography, photogrammetry and GIS software were used to produce 3D models of the buttresses, roots and humus mounds of large trees in primary forests dominated by Eucalyptus regnans in Tasmania. Models of 29, in situ eucalypts were made and analysed. 3D models of example eucalypt roots, logging debris, rainforest tree species, fallen trees, branches, root and trunk slices, and soil profiles were also derived. Measurements in 2D, from earlier work, of three buttress 'logs' were added to the data set. The 3D models had high spatial resolution. The modelling allowed checking and correction of field measurements. Tree anatomical detail was formulated, such as buttress shape, humus volume, root volume in the under-sampled zone and trunk hollow area. The allometric relationships developed link diameter at breast height and ground slope, to SOC and tree trunk carbon, the latter including a correction for senescence. These formulae can be applied to stand-level carbon accounting. The formulae allow the typically measured, inter-tree SOC to be corrected for not sampling near large trees. The 3D models developed are irreplaceable, being for increasingly rare, large trees, and they could be useful to other scientific endeavours.

Nonlinear Evolution of Counter-Propagating Whistler Mode Waves Excited by Anisotropic Electrons Within the Equatorial Source Region: 1-D PIC Simulations

NASA Astrophysics Data System (ADS)

Chen, Huayue; Gao, Xinliang; Lu, Quanming; Sun, Jicheng; Wang, Shui

2018-02-01

Nonlinear physical processes related to whistler mode waves are attracting more and more attention for their significant role in reshaping whistler mode spectra in the Earth's magnetosphere. Using a 1-D particle-in-cell simulation model, we have investigated the nonlinear evolution of parallel counter-propagating whistler mode waves excited by anisotropic electrons within the equatorial source region. In our simulations, after the linear phase of whistler mode instability, the strong electrostatic standing structures along the background magnetic field will be formed, resulting from the coupling between excited counter-propagating whistler mode waves. The wave numbers of electrostatic standing structures are about twice those of whistler mode waves generated by anisotropic hot electrons. Moreover, these electrostatic standing structures can further be coupled with either parallel or antiparallel propagating whistler mode waves to excite high-k modes in this plasma system. Compared with excited whistler mode waves, these high-k modes typically have 3 times wave number, same frequency, and about 2 orders of magnitude smaller amplitude. Our study may provide a fresh view on the evolution of whistler mode waves within their equatorial source regions in the Earth's magnetosphere.

A 3D surface imaging system for assessing human obesity

NASA Astrophysics Data System (ADS)

Xu, B.; Yu, W.; Yao, M.; Yao, X.; Li, Q.; Pepper, M. R.; Freeland-Graves, J. H.

2009-08-01

The increasing prevalence of obesity suggests a need to develop a convenient, reliable and economical tool for assessment of this condition. Three-dimensional (3D) body surface imaging has emerged as an exciting technology for estimation of body composition. This paper presents a new 3D body imaging system, which was designed for enhanced portability, affordability, and functionality. In this system, stereo vision technology was used to satisfy the requirements for a simple hardware setup and fast image acquisitions. The portability of the system was created via a two-stand configuration, and the accuracy of body volume measurements was improved by customizing stereo matching and surface reconstruction algorithms that target specific problems in 3D body imaging. Body measurement functions dedicated to body composition assessment also were developed. The overall performance of the system was evaluated in human subjects by comparison to other conventional anthropometric methods, as well as air displacement plethysmography, for body fat assessment.

Three-Dimensional Rebar Graphene.

PubMed

Sha, Junwei; Salvatierra, Rodrigo V; Dong, Pei; Li, Yilun; Lee, Seoung-Ki; Wang, Tuo; Zhang, Chenhao; Zhang, Jibo; Ji, Yongsung; Ajayan, Pulickel M; Lou, Jun; Zhao, Naiqin; Tour, James M

2017-03-01

Free-standing robust three-dimensional (3D) rebar graphene foams (GFs) were developed by a powder metallurgy template method with multiwalled carbon nanotubes (MWCNTs) as a reinforcing bar, sintered Ni skeletons as a template and catalyst, and sucrose as a solid carbon source. As a reinforcement and bridge between different graphene sheets and carbon shells, MWCNTs improved the thermostability, storage modulus (290.1 kPa) and conductivity (21.82 S cm -1 ) of 3D GF resulting in a high porosity and structurally stable 3D rebar GF. The 3D rebar GF can support >3150× the foam's weight with no irreversible height change, and shows only a ∼25% irreversible height change after loading >8500× the foam's weight. The 3D rebar GF also shows stable performance as a highly porous electrode in lithium ion capacitors (LICs) with an energy density of 32 Wh kg -1 . After 500 cycles of testing at a high current density of 6.50 mA cm -2 , the LIC shows 78% energy density retention. These properties indicate promising applications with 3D rebar GFs in devices requiring stable mechanical and electrochemical properties.

Simulation-Guided 3D Nanomanufacturing via Focused Electron Beam Induced Deposition

DOE PAGES

Fowlkes, Jason D.; Winkler, Robert; Lewis, Brett B.; ...

2016-06-10

Focused electron beam induced deposition (FEBID) is one of the few techniques that enables direct-write synthesis of free-standing 3D nanostructures. While the fabrication of simple architectures such as vertical or curving nanowires has been achieved by simple trial and error, processing complex 3D structures is not tractable with this approach. This is due, inpart, to the dynamic interplay between electron–solid interactions and the transient spatial distribution of absorbed precursor molecules on the solid surface. Here, we demonstrate the ability to controllably deposit 3D lattice structures at the micro/nanoscale, which have received recent interest owing to superior mechanical and optical properties.more » Moreover, a hybrid Monte Carlo–continuum simulation is briefly overviewed, and subsequently FEBID experiments and simulations are directly compared. Finally, a 3D computer-aided design (CAD) program is introduced, which generates the beam parameters necessary for FEBID by both simulation and experiment. In using this approach, we demonstrate the fabrication of various 3D lattice structures using Pt-, Au-, and W-based precursors.« less

42 CFR 10.21 - Exclusion of orphan drugs for certain covered entities.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) of this section shall only apply to the following covered entities: free-standing cancer hospitals... process. (d) Use of group purchasing organizations by a free-standing cancer hospital. (1) A free-standing cancer hospital enrolled under section 340B(a)(4)(M) must also comply with the prohibition against using...

42 CFR 10.21 - Exclusion of orphan drugs for certain covered entities.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) of this section shall only apply to the following covered entities: free-standing cancer hospitals... process. (d) Use of group purchasing organizations by a free-standing cancer hospital. (1) A free-standing cancer hospital enrolled under section 340B(a)(4)(M) must also comply with the prohibition against using...

Large Scale System Defense

DTIC Science & Technology

2008-10-01

AD); Aeolos, a distributed intrusion detection and event correlation infrastructure; STAND, a training-set sanitization technique applicable to ADs...UU 18. NUMBER OF PAGES 25 19a. NAME OF RESPONSIBLE PERSON Frank H. Born a. REPORT U b. ABSTRACT U c . THIS PAGE U 19b. TELEPHONE...Summary of findings 2 (a) Automatic Patch Generation 2 (b) Better Patch Management 2 ( c ) Artificial Diversity 3 (d) Distributed Anomaly Detection 3

Black bear (Ursus americanus Pallas) feeding damage across timber harvest edges in northern California coast redwood (Sequoia sempervirens[D. Don] Endl.) forests, USA

USGS Publications Warehouse

Russell, W.H.; Carnell, K.; McBride, J.R.

2001-01-01

Feeding damage to trees by black bears (Ursus americanus Pallas) was recorded in proximity to timber harvest edges in harvested and old-growth stands of coast redwood (Sequoia sempervirens [D. Don] Endl.) in northern California, USA. Bears exhibited distinct preference in their feeding patterns related to stand structure and composition and to distance from the timber-harvest edge. Most damage was recorded within regenerating stands. Regression analysis indicated that density of damaged trees was negatively correlated with distance from timber harvest edges within old-growth stands. A significant negative correlation was also found between the density of trees damaged by bears and habitat diversity (H') as measured by the Shannon diversity index. In addition, bears exhibited preference for pole-size trees (dbh = 10-50 cm) over all other size classes, and coast redwood over other species. In general, damage by bears appeared to act as a natural thinning agent in even-aged stands. No damage was recorded in old-growth stands except in close proximity to the timber-harvest edge where subcanopy recruitment was high.

Treatment of an old-growth stand and its effects on birds, ants, and large woody debris: A case study. Forest Service general technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bull, E.L.; Torgersen, T.R.; Blumton, A.K.

1995-09-01

An old-structure stand with large amounts of tree mortality was treated to accelerate regeneration and reduce fuel loads but still maintain its function as old growth for selected bird species. The smll-diameter (less than 15 inches in diameter at breast height (d.b.h.)), dead trees were removed as was some of the down wood less than 15 inches in diameter at the large end. All live trees of any size and all dead trees equal to or greater than 15 inches d.b.h. were retained. Vaux`s swifts (Chaetura vauxi) and pileated woodpeckers (Dryocopus pileatus) continued to use the stand after harvest formore » nesting and roosting. Brown-headed cowbirds (molothrus ater) were more than twice as common in the treated stand as in an adjacent unlogged, control stand. In a comparison before and after harvest in the treated stand, the number of logs increased, the number of logs with ants increased, but the percentage of logs with ants decreased.« less

Direct Observation of Gold Nanoparticle Assemblies with the Porin MspA on Mica

PubMed Central

Basel, Matthew T.; Dani, Raj Kumar; Kang, Myungshim; Pavlenok, Mikhail; Chikan, Viktor; Smith, Paul E.; Niederweis, Michael

2009-01-01

The octameric porin MspA from Mycobacterium smegmatis is sufficiently stable to form a non-membrane-supported stand-alone porin on Mica surfaces. About 98% of all MspA octamers were found to stand upright on Mica, with their periplasmic loop regions bound to the hydrophilic Mica surface. Both, small (d = 3.7 nm) and large (d = 17 nm) gold nanoparticles bind to MspA, however in different positions: small gold nanoparticles bind within the MspA pore, whereas the large gold nanoparticles bind to the upper region of MspA. These experiments demonstrate that gold nanoparticles can be positioned at different, well-defined distances from the underlying surface using the MspA pore as a template. These findings represent a significant step towards the use of electrically insulating stable proteins in combination with metal nanoparticles in nanodevices. PMID:19236086

Credit WCT. Photographic copy of photograph, view north across "neutralization ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view north across "neutralization pond" at Test Stand "D," showing complete Dd station with new Y-Stage and Z-Stage steam-driven ejectors, and "Hyprox" steam generator which powered ejectors. (JPL negative no. 384-3356-B, 20 November 1962) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

Butt log quality of trees in Pennsylvania oak stands

Treesearch

Martin E. Dale; Robert L. Brisbin; Robert L. Brisbin

1985-01-01

Describes the distribution of sawtimber trees by diameter at breast height (d.b.h.) and grade for eight hardwood species in upland oak stands of Pennsylvania. The proportion of trees by d.b.h. and grade revealed differences between species. The quality of northern red oak, white oak, and yellow-poplar appeared inherently better than that of red maple, chestnut oak, and...

Occurrence and larval movement of Diatraea saccharalis (Lepidoptera: Crambidae) in seed mixes of non-Bt and Bt pyramid corn.

PubMed

Wangila, David S; Leonard, B Rogers; Ghimire, Mukti N; Bai, Yaoyu; Zhang, Liping; Yang, Yunlong; Emfinger, Karla D; Head, Graham P; Yang, Fei; Niu, Ying; Huang, Fangneng

2013-10-01

Larval movement of target pest populations among Bt and non-Bt plants is a major concern in the use of a seed mixture refuge strategy for Bt resistance management. In this study, occurrence and larval movement of the sugarcane borer, Diatraea saccharalis (F.), were evaluated in four planting patterns of non-Bt and Bt plants containing Genuity® SmartStax(TM) traits in 2009-2011. The four planting patterns were: (1) a pure stand of 27 Bt plants; (2) one non-Bt plant in the center, surrounded by 26 Bt plants; (3) a pure stand of 27 non-Bt plants; (4) one Bt plant in the center, surrounded by 26 non-Bt plants. Studies were conducted under four conditions: (1) open field with natural infestation; (2) greenhouse with artificial infestations; open field with artificial infestations (3) on the center plants only and (4) on every plant. The major objective of this study was to determine whether refuge plants in a seed mixture strategy could provide a comparable refuge population of D. saccharalis to a 'structured refuge' planting. Larvae of D. saccharalis showed the ability to move from infested plants to at least four plants away, as well as to adjacent rows, but the majority remained within the infested row. However, the number of larvae found on the non-Bt plants in the mixture plantings was not significantly reduced compared with the pure stand of non-Bt corn. The results of this study show that refuge plants in a seed mixture may be able to provide a comparable refuge population of D. saccharalis to a structured refuge planting. © 2013 Society of Chemical Industry.

2. Credit BG. Looking west at east facade of Steam ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Credit BG. Looking west at east facade of Steam Generator Plant, Building 4280/E-81; steam generators have been removed as part of dismantling program for Test Stand 'D.' Metal cylindrical objects to left of door were roof vents. The steam-driven ejector system for Dv Cell is clearly visible on the east side of Test Stand 'D' tower. The X-stage ejector is vertically installed at the bottom left of the tower, Y-stage is horizontally positioned close to the tower top, and the Z- and Z-1 stages are attached to the top of the interstage condenser. Light-colored piping is thermally insulated steam line. - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Steam Generator Plant, Edwards Air Force Base, Boron, Kern County, CA

Three-Dimensional Bi₂Te₃ Networks of Interconnected Nanowires: Synthesis and Optimization.

PubMed

Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martín-González, Marisol

2018-05-18

Self-standing Bi₂Te₃ networks of interconnected nanowires were fabricated in three-dimensional porous anodic alumina templates (3D⁻AAO) with a porous structure spreading in all three spatial dimensions. Pulsed electrodeposition parameters were optimized to grow highly oriented Bi₂Te₃ interconnected nanowires with stoichiometric composition inside those 3D⁻AAO templates. The nanowire networks were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and Raman spectroscopy. The results are compared to those obtained in films and 1D nanowires grown under similar conditions. The crystalline structure and composition of the 3D Bi⁻Te nanowire network are finely tuned by controlling the applied voltage and the relaxation time off at zero current density during the deposition. With this fabrication method, and controlling the electrodeposition parameters, stoichiometric Bi₂Te₃ networks of interconnected nanowires have been obtained, with a preferential orientation along [1 1 0], which makes them optimal candidates for out-of-plane thermoelectric applications. Moreover, the templates in which they are grown can be dissolved and the network of interconnected nanowires is self-standing without affecting its composition and orientation properties.

Multimodal image registration of the scoliotic torso for surgical planning

PubMed Central

2013-01-01

Background This paper presents a method that registers MRIs acquired in prone position, with surface topography (TP) and X-ray reconstructions acquired in standing position, in order to obtain a 3D representation of a human torso incorporating the external surface, bone structures, and soft tissues. Methods TP and X-ray data are registered using landmarks. Bone structures are used to register each MRI slice using an articulated model, and the soft tissue is confined to the volume delimited by the trunk and bone surfaces using a constrained thin-plate spline. Results The method is tested on 3 pre-surgical patients with scoliosis and shows a significant improvement, qualitatively and using the Dice similarity coefficient, in fitting the MRI into the standing patient model when compared to rigid and articulated model registration. The determinant of the Jacobian of the registration deformation shows higher variations in the deformation in areas closer to the surface of the torso. Conclusions The novel, resulting 3D full torso model can provide a more complete representation of patient geometry to be incorporated in surgical simulators under development that aim at predicting the effect of scoliosis surgery on the external appearance of the patient’s torso. PMID:23289431

Body centre of mass movement in the sound horse.

PubMed

Buchner, H H; Obermüller, S; Scheidl, M

2000-11-01

The body centre of mass (BCM) is a key factor in the analysis of equine locomotion, as its position and movement determines the distribution and magnitude of loads on the limbs. In this study, the three-dimensional (3D) movement of the BCM in walking and trotting horses was assessed using a kinematic, segmental method. Thirty markers representing 20 body segments were recorded in 12 sound horses while standing, walking and trotting on a treadmill using a high-speed video system. Based on segmental inertial data, 3D positions of the segmental centres of mass as well as the total BCM were calculated. The position within the trunk during square standing and the movements of the BCM were determined for the three planes. The position of the BCM in the standing horse is presented relative to external reference points. At the trot, vertical displacement amplitude of the BCM amounted to 53 (6) mm as mean (sd), which was 27% smaller than external trunk movement. Medio-lateral displacement amplitude of the BCM was 19 (4) mm, 34% less than trunk amplitude. Sagittal forward-backward oscillations of the BCM independent from general forward movement were 13 (3) mm, being 24% less than trunk movements. At the walk, vertical, medio-lateral and sagittal BCM movements were smaller than trunk movements by 43, 65 and 65% respectively. The results show reduced and efficient BCM movements compared to the trunk and form a basis for the assessment of various clinical conditions such as lameness, the influence of a rider and various dressage performances. Copyright 2000 Harcourt Publishers Ltd.

Recognition of complex human behaviours using 3D imaging for intelligent surveillance applications

NASA Astrophysics Data System (ADS)

Yao, Bo; Lepley, Jason J.; Peall, Robert; Butler, Michael; Hagras, Hani

2016-10-01

We introduce a system that exploits 3-D imaging technology as an enabler for the robust recognition of the human form. We combine this with pose and feature recognition capabilities from which we can recognise high-level human behaviours. We propose a hierarchical methodology for the recognition of complex human behaviours, based on the identification of a set of atomic behaviours, individual and sequential poses (e.g. standing, sitting, walking, drinking and eating) that provides a framework from which we adopt time-based machine learning techniques to recognise complex behaviour patterns.

Normative 3D opto-electronic stereo-photogrammetric posture and spine morphology data in young healthy adult population

PubMed Central

2017-01-01

Design: Observational cross-sectional study. The current study aims to yield normative data: i.e., the physiological standard for 30 selected quantitative 3D parameters that accurately capture and describe a full-skeleton, upright-standing attitude. Specific and exclusive consideration was given to three distinct categories: postural, spine morphology and pelvic parameters. To capture such 3D parameters, the authors selected a non-ionising 3D opto-electronic stereo-photogrammetric approach. This required the identification and measurement of 27 body landmarks, each specifically tagged with a skin marker. As subjects for the measurement of these parameters, a cohort of 124 asymptomatic young adult volunteers was recruited. All parameters were identified and measured within this group. Postural and spine morphology data have been compared between genders. In this regard, only five statistically significant differences were found: pelvis width, pelvis torsion, the “lumbar” lordosis angle value, the lumbar curve length, and the T12-L5 anatomically-bound lumbar angle value. The “thoracic” kyphosis mean angle value was the same in both sexes and, even if, derived from skin markers placed on spinous processes it resulted in perfect agreement with the X-ray based literature. As regards lordosis, a direct comparison was more difficult because methods proposed in the literature differ as to the number and position of vertebrae under consideration, and their related angle values. However, when the L1 superior–L5 inferior end plate Cobb angle was considered, these results aligned strongly with the existing literature. Asymmetry was a standard postural-spinal feature for both sexes. Each subject presented some degree of leg length discrepancy (LLD) with μ = 9.37mm. This was associated with four factors: unbalanced posture and/or underfoot loads, spinal curvature in the frontal plane, and pelvis torsion. This led to the additional study of the effect of LLD equalisation influence on upright posture, relying on a sub-sample of 100 subjects (51 males, 49 females). As a result of the equalisation, about 82% of this sub-sample showed improvement in standing posture, mainly in the frontal plane; while in the sagittal plane less than 1/3 of the sub-sample showed evidence of change in spinal angles. A significant variation was found in relation to pelvis torsion: 46% of subjects showed improvement, 49% worsening. The method described in study presents several advantages: non-invasive aspect; relatively short time for a complete postural evaluation with many clinically useful 3D and 2D anatomical/biomechanical/clinical parameters; analysis of real neutral unconstrained upright standing posture. PMID:28640899

Three-dimensional manipulation of single cells using surface acoustic waves.

PubMed

Guo, Feng; Mao, Zhangming; Chen, Yuchao; Xie, Zhiwei; Lata, James P; Li, Peng; Ren, Liqiang; Liu, Jiayang; Yang, Jian; Dao, Ming; Suresh, Subra; Huang, Tony Jun

2016-02-09

The ability of surface acoustic waves to trap and manipulate micrometer-scale particles and biological cells has led to many applications involving "acoustic tweezers" in biology, chemistry, engineering, and medicine. Here, we present 3D acoustic tweezers, which use surface acoustic waves to create 3D trapping nodes for the capture and manipulation of microparticles and cells along three mutually orthogonal axes. In this method, we use standing-wave phase shifts to move particles or cells in-plane, whereas the amplitude of acoustic vibrations is used to control particle motion along an orthogonal plane. We demonstrate, through controlled experiments guided by simulations, how acoustic vibrations result in micromanipulations in a microfluidic chamber by invoking physical principles that underlie the formation and regulation of complex, volumetric trapping nodes of particles and biological cells. We further show how 3D acoustic tweezers can be used to pick up, translate, and print single cells and cell assemblies to create 2D and 3D structures in a precise, noninvasive, label-free, and contact-free manner.

3D numerical modelling of a willow vegetated river/floodplain system

NASA Astrophysics Data System (ADS)

Wilson, C. A. M. E.; Yagci, O.; Rauch, H.-P.; Olsen, N. R. B.

2006-07-01

SummaryUsing a three-dimensional finite volume code with standard k- ɛ turbulence closure the hydraulic impact of willow stands ( Salix alba and Salix fragilis) on the velocity distribution was modelled. The additional hydraulic resistance of the willow stands was modelled separately to the bed resistance using a drag force term that was introduced into the Navier-Stokes equations. Two flood events of varying magnitude and stages of plant development were simulated using this approach. The river comprises an asymmetric compound channel with vegetated floodplain of reach length 170 m. The willow development has been monitored annually and this information was used to define the density of the willow stands (average number per m 2) and its variation as a function of stand height. During both flood events the willow stands were submerged and in pronation. The willow stands were modelled in bending as well as in their undisturbed vertical state. Modelling the willow stands as vertical or in bending was found to have a major impact on the computed velocity profiles. The impact of using a drag-force approach based on a non-uniform projected area distribution was found to be greater when the plants are modelled vertically than when the plants are modelled in high degrees of bending. In field studies involving flexible plants without leaves, the determination of the drag coefficient is of less importance compared to the need to quantify the degree by which plants are in pronation.

A standing wave linear ultrasonic motor operating in in-plane expanding and bending modes.

PubMed

Chen, Zhijiang; Li, Xiaotian; Ci, Penghong; Liu, Guoxi; Dong, Shuxiang

2015-03-01

A novel standing wave linear ultrasonic motor operating in in-plane expanding and bending modes was proposed in this study. The stator (or actuator) of the linear motor was made of a simple single Lead Zirconate Titanate (PZT) ceramic square plate (15 × 15 × 2 mm(3)) with a circular hole (D = 6.7 mm) in the center. The geometric parameters of the stator were computed with the finite element analysis to produce in-plane bi-mode standing wave vibration. The calculated results predicted that a driving tip attached at midpoint of one edge of the stator can produce two orthogonal, approximate straight-line trajectories, which can be used to move a slider in linear motion via frictional forces in forward or reverse direction. The investigations showed that the proposed linear motor can produce a six times higher power density than that of a previously reported square plate motor.

Manual felling time and productivity in southern forests

Treesearch

D. Lortz; R. Kluender; W McCoy; [and others

1997-01-01

Sixteen stands were harvested by either clearcut, shelterwood, group selection, or single-tree selection methods. Three of the stands had uneven-aged structure. The other 13 were typical, mature, even-aged stands. Harvest intensity (proportion of basal area removed) ranged from 0.27 to 1.00. Harvested sites were similar in slope, average diameter at breast height (d.b....

Macroporous nanowire nanoelectronic scaffolds for synthetic tissues

NASA Astrophysics Data System (ADS)

Tian, Bozhi; Liu, Jia; Dvir, Tal; Jin, Lihua; Tsui, Jonathan H.; Qing, Quan; Suo, Zhigang; Langer, Robert; Kohane, Daniel S.; Lieber, Charles M.

2012-11-01

The development of three-dimensional (3D) synthetic biomaterials as structural and bioactive scaffolds is central to fields ranging from cellular biophysics to regenerative medicine. As of yet, these scaffolds cannot electrically probe the physicochemical and biological microenvironments throughout their 3D and macroporous interior, although this capability could have a marked impact in both electronics and biomaterials. Here, we address this challenge using macroporous, flexible and free-standing nanowire nanoelectronic scaffolds (nanoES), and their hybrids with synthetic or natural biomaterials. 3D macroporous nanoES mimic the structure of natural tissue scaffolds, and they were formed by self-organization of coplanar reticular networks with built-in strain and by manipulation of 2D mesh matrices. NanoES exhibited robust electronic properties and have been used alone or combined with other biomaterials as biocompatible extracellular scaffolds for 3D culture of neurons, cardiomyocytes and smooth muscle cells. Furthermore, we show the integrated sensory capability of the nanoES by real-time monitoring of the local electrical activity within 3D nanoES/cardiomyocyte constructs, the response of 3D-nanoES-based neural and cardiac tissue models to drugs, and distinct pH changes inside and outside tubular vascular smooth muscle constructs.

Membrane-bound MinDE complex acts as a toggle switch that drives Min oscillation coupled to cytoplasmic depletion of MinD

PubMed Central

Vecchiarelli, Anthony G.; Li, Min; Mizuuchi, Michiyo; Hwang, Ling Chin; Seol, Yeonee; Neuman, Keir C.; Mizuuchi, Kiyoshi

2016-01-01

The Escherichia coli Min system self-organizes into a cell-pole to cell-pole oscillator on the membrane to prevent divisions at the cell poles. Reconstituting the Min system on a lipid bilayer has contributed to elucidating the oscillatory mechanism. However, previous in vitro patterns were attained with protein densities on the bilayer far in excess of those in vivo and failed to recapitulate the standing wave oscillations observed in vivo. Here we studied Min protein patterning at limiting MinD concentrations reflecting the in vivo conditions. We identified “burst” patterns—radially expanding and imploding binding zones of MinD, accompanied by a peripheral ring of MinE. Bursts share several features with the in vivo dynamics of the Min system including standing wave oscillations. Our data support a patterning mechanism whereby the MinD-to-MinE ratio on the membrane acts as a toggle switch: recruiting and stabilizing MinD on the membrane when the ratio is high and releasing MinD from the membrane when the ratio is low. Coupling this toggle switch behavior with MinD depletion from the cytoplasm drives a self-organized standing wave oscillator. PMID:26884160

Membrane-bound MinDE complex acts as a toggle switch that drives Min oscillation coupled to cytoplasmic depletion of MinD.

PubMed

Vecchiarelli, Anthony G; Li, Min; Mizuuchi, Michiyo; Hwang, Ling Chin; Seol, Yeonee; Neuman, Keir C; Mizuuchi, Kiyoshi

2016-03-15

The Escherichia coli Min system self-organizes into a cell-pole to cell-pole oscillator on the membrane to prevent divisions at the cell poles. Reconstituting the Min system on a lipid bilayer has contributed to elucidating the oscillatory mechanism. However, previous in vitro patterns were attained with protein densities on the bilayer far in excess of those in vivo and failed to recapitulate the standing wave oscillations observed in vivo. Here we studied Min protein patterning at limiting MinD concentrations reflecting the in vivo conditions. We identified "burst" patterns--radially expanding and imploding binding zones of MinD, accompanied by a peripheral ring of MinE. Bursts share several features with the in vivo dynamics of the Min system including standing wave oscillations. Our data support a patterning mechanism whereby the MinD-to-MinE ratio on the membrane acts as a toggle switch: recruiting and stabilizing MinD on the membrane when the ratio is high and releasing MinD from the membrane when the ratio is low. Coupling this toggle switch behavior with MinD depletion from the cytoplasm drives a self-organized standing wave oscillator.

Sap flux density and stomatal conductance of European beech and common oak trees in pure and mixed stands during the summer drought of 2003

NASA Astrophysics Data System (ADS)

Jonard, F.; André, F.; Ponette, Q.; Vincke, C.; Jonard, M.

2011-10-01

SummarySap flux density of European beech and common oak trees was determined from sap flow measurements in pure and mixed stands during the summer drought of 2003. Eight trees per species and per stand were equipped with sap flow sensors. Soil water content was monitored in each stand at different depths by using time-domain reflectometry (TDR). Leaf area index and vertical root distribution were also investigated during the growing season. From sap flux density ( SFD) data, mean stomatal conductance of individual trees ( G s) was calculated by inverting the Penman-Monteith equation. Linear mixed models were developed to analyse the effects of species and stand type (pure vs. mixed) on SFD and G s and on their sensitivity to environmental variables (vapour pressure deficit ( D), incoming solar radiation ( R G), and relative extractable water ( REW)). For reference environmental conditions, we did not find any tree species or stand type effects on SFD. The sensitivity of SFD to D was higher for oak than for beech in the pure stands ( P < 0.0001) but the mixing of species reduced it for oak and increased it for beech, so that the sensitivity of SFD to D became higher for beech than for oak in the mixed stand ( P < 0.0001). At reference conditions, G s was significantly higher for beech compared to oak (2.1 and 1.8 times in the pure and mixed stand, respectively). This was explained by a larger beech sapwood-to-leaf area ratio compared to oak. The sensitivity of G s to REW was higher for beech than for oak and was ascribed to a higher vulnerability of beech to air embolism and to a more sensitive stomatal regulation. The sensitivity of beech G s to REW was lower in the mixed than in the pure stand, which could be explained by a better sharing of the resources in the mixture, by facilitation processes (hydraulic lift), and by a rainfall partitioning in favour of beech.

Dairy cow preferences for soft or hard flooring when standing or walking.

PubMed

Telezhenko, E; Lidfors, L; Bergsten, C

2007-08-01

Concrete is the most commonly used alley flooring in confined dairy herds because of its qualities of construction and ease of cleaning. Nevertheless, the hardness, abrasiveness, and slipperiness of concrete floors have adverse effects on animal well-being and health, and yielding rubber flooring is becoming popular as a way of improving the flooring conditions on walkways. The aim of this study was to investigate preferences of dairy cows for rubber compared with concrete flooring under the conditions of a commercial dairy farm. The study was conducted in an organic dairy herd with free-stall housing. Floor preference was tested on groups of standing cows in a 120-m2 holding pen before milking, and 1 yr later on a 12- x 3-m walkway. The holding pen and the walkway were divided lengthwise into 2 identical sections. Two types of solid rubber mats (soft and extra soft) were tested against solid concrete in the holding pen. Slatted and solid rubber mats were tested against slatted concrete in the walkway. Each floor type was tested over 4 d on the left side and 4 d on the right side of the holding pen and the walkway, respectively. Concrete flooring on both sides of the sections was tested as a control before the testing of different section materials. All observations of the distribution of cows in the sections were made from video recordings captured in association with the afternoon milking. The number of cows on each section was recorded approximately every 7 min in the holding pen, and continuously on the walkway. A significantly higher proportion of cows stood on the side with the soft and extra soft rubber mats (65.1 +/- 2.7 and 69.3 +/- 2.6%, respectively, mean +/- SEM) compared with the control distribution when only the solid concrete was available (50.9 +/- 3.9%). A significantly higher proportion of nonlame cows walked exclusively on the side with the slatted (64.5 +/- 5.4%, d 4) or solid rubber mats (68.2 +/- 5.1%, d 4) compared with controls (28.9 +/- 4.3%). Lame cows within a group of walking cows did not show a higher preference for soft flooring as distinct as nonlame cows (52.7 +/- 6.9 and 59.4 +/- 6.2% for the solid and slatted rubber mats, respectively, at d 4 vs. 40.3 +/- 6.2% for control), presumably because of competition with other, higher ranked cows. It was concluded that the majority of cows preferred to walk and stand on soft rubber rather than on concrete flooring.

Pelvic Morphology, Body Posture and Standing Balance Characteristics of Adolescent Able-Bodied and Idiopathic Scoliosis Girls

PubMed Central

Stylianides, Georgios A.; Dalleau, Georges; Begon, Mickaël; Rivard, Charles-Hilaire; Allard, Paul

2013-01-01

The purpose of this study was to determine how pelvic morphology, body posture, and standing balance variables of scoliotic girls differ from those of able-bodied girls, and to classify neuro-biomechanical variables in terms of a lower number of unobserved variables. Twenty-eight scoliotic and twenty-five non-scoliotic able-bodied girls participated in this study. 3D coordinates of ten anatomic body landmarks were used to describe pelvic morphology and trunk posture using a Flock of Birds system. Standing balance was measured using a force plate to identify the center of pressure (COP), and its anteroposterior (AP) and mediolateral (ML) displacements. A multivariate analysis of variance (MANOVA) was performed to determine differences between the two groups. A factor analysis was used to identify factors that best describe both groups. Statistical differences were identified between the groups for each of the parameter types. While spatial orientation of the pelvis was similar in both groups, five of the eight trunk postural variables of the scoliotic group were significantly different that the able-bodied group. Also, five out of the seven standing balance variables were higher in the scoliotic girls. Approximately 60% of the variation is supported by 4 factors that can be associated with a set of variables; standing balance variables (factor 1), body posture variables (factor 2), and pelvic morphology variables (factors 3 and 4). Pelvic distortion, body posture asymmetry, and standing imbalance are more pronounced in scoliotic girls, when compared to able-bodied girls. These findings may be beneficial when addressing balance and ankle proprioception exercises for the scoliotic population. PMID:23875021

Experimental and simulation flow rate analysis of the 3/2 directional pneumatic valve

NASA Astrophysics Data System (ADS)

Blasiak, Slawomir; Takosoglu, Jakub E.; Laski, Pawel A.; Pietrala, Dawid S.; Zwierzchowski, Jaroslaw; Bracha, Gabriel; Nowakowski, Lukasz; Blasiak, Malgorzata

The work includes a study on the comparative analysis of two test methods. The first method - numerical method, consists in determining the flow characteristics with the use of ANSYS CFX. A modeled poppet directional valve 3/2 3D CAD software - SolidWorks was used for this purpose. Based on the solid model that was developed, simulation studies of the air flow through the way valve in the software for computational fluid dynamics Ansys CFX were conducted. The second method - experimental, entailed conducting tests on a specially constructed test stand. The comparison of the test results obtained on the basis of both methods made it possible to determine the cross-correlation. High compatibility of the results confirms the usefulness of the numerical procedures. Thus, they might serve to determine the flow characteristics of directional valves as an alternative to a costly and time-consuming test stand.

High-Density Three-Dimension Graphene Macroscopic Objects for High-Capacity Removal of Heavy Metal Ions

PubMed Central

Li, Weiwei; Gao, Song; Wu, Liqiong; Qiu, Shengqiang; Guo, Yufen; Geng, Xiumei; Chen, Mingliang; Liao, Shutian; Zhu, Chao; Gong, Youpin; Long, Mingsheng; Xu, Jianbao; Wei, Xiangfei; Sun, Mengtao; Liu, Liwei

2013-01-01

The chemical vapor deposition (CVD) fabrication of high-density three-dimension graphene macroscopic objects (3D-GMOs) with a relatively low porosity has not yet been realized, although they are desirable for applications in which high mechanical and electrical properties are required. Here, we explore a method to rapidly prepare the high-density 3D-GMOs using nickel chloride hexahydrate (NiCl2·6H2O) as a catalyst precursor by CVD process at atmospheric pressure. Further, the free-standing 3D-GMOs are employed as electrolytic electrodes to remove various heavy metal ions. The robust 3D structure, high conductivity (~12 S/cm) and large specific surface area (~560 m2/g) enable ultra-high electrical adsorption capacities (Cd2+ ~ 434 mg/g, Pb2+ ~ 882 mg/g, Ni2+ ~ 1,683 mg/g, Cu2+ ~ 3,820 mg/g) from aqueous solutions and fast desorption. The current work has significance in the studies of both the fabrication of high-density 3D-GMOs and the removal of heavy metal ions. PMID:23821107

A flexible 3D nitrogen-doped carbon foam@CNTs hybrid hosting TiO2 nanoparticles as free-standing electrode for ultra-long cycling lithium-ion batteries

NASA Astrophysics Data System (ADS)

Yuan, Wei; Wang, Boya; Wu, Hao; Xiang, Mingwu; Wang, Qiong; Liu, Heng; Zhang, Yun; Liu, Huakun; Dou, Shixue

2018-03-01

Free-standing electrodes have stood out from the electrode pack, owing to their advantage of abandoning the conventional polymeric binder and conductive agent, thus increasing the specific capacity of lithium-ion batteries. Nevertheless, their practical application is hampered by inferior electrical conductivity and complex manufacturing process. To this end, we report here a facile approach to fabricate a flexible 3D N-doped carbon foam/carbon nanotubes (NCF@CNTs) hybrid to act as the current collector and host scaffold for TiO2 particles, which are integrated into a lightweight free-standing electrode (NCF@CNTs-TiO2). In the resulting architecture, ultra-fine TiO2 nanoparticles are homogeneously anchored in situ into the N-doped NCF@CNTs framework with macro- and meso-porous structure, wrapped by a dense CNT layer, cooperatively enhances the electrode flexibility and forms an interconnected conductive network for electron/ion transport. As a result, the as-prepared NCF@CNTs-TiO2 electrode exhibits excellent lithium storage performance with high specific capacity of 241 mAh g-1 at 1 C, superb rate capability of 145 mAh g-1 at 20 C, ultra-long cycling stability with an ultra-low capacity decay of 0.0037% per cycle over 2500 cycles, and excellent thermal stability with ∼94% capacity retention over 100 cycles at 55 °C.

Two weeks of additional standing balance circuit classes during inpatient rehabilitation are cost saving and effective: an economic evaluation.

PubMed

Treacy, Daniel; Howard, Kirsten; Hayes, Alison; Hassett, Leanne; Schurr, Karl; Sherrington, Catherine

2018-01-01

Among people admitted for inpatient rehabilitation, is usual care plus standing balance circuit classes more cost-effective than usual care alone? Cost-effectiveness study embedded within a randomised controlled trial with concealed allocation, assessor blinding and intention-to-treat analysis. 162 rehabilitation inpatients from a metropolitan hospital in Sydney, Australia. The experimental group received a 1-hour standing balance circuit class, delivered three times a week for 2 weeks, in addition to usual therapy. The circuit classes were supervised by one physiotherapist and one physiotherapy assistant for up to eight patients. The control group received usual therapy alone. Costs were estimated from routinely collected hospital use data in the 3 months after randomisation. The functional outcome measure was mobility measured at 3 months using the Short Physical Performance Battery administered by a blinded assessor. An incremental analysis was conducted and the joint probability distribution of costs and outcomes was examined using bootstrapping. The median cost savings for the intervention group was AUD4,741 (95% CI 137 to 9,372) per participant; 94% of bootstraps showed that the intervention was both effective and cost saving. Two weeks of additional standing balance circuit classes delivered in addition to usual therapy resulted in decreased healthcare costs at 3 months in hospital inpatients admitted for rehabilitation. There is a high probability that this intervention is both cost saving and effective. ACTRN12611000412932. [Treacy D, Howard K, Hayes A, Hassett L, Schurr K, Sherrington C (2018) Two weeks of additional standing balance circuit classes during inpatient rehabilitation are cost saving and effective: an economic evaluation. Journal of Physiotherapy 64: 41-47]. Copyright © 2017 Australian Physiotherapy Association. Published by Elsevier B.V. All rights reserved.

Study of Noise-Certification Standards for Aircraft Engines. Volume 2. Procedures for Measuring Far Field Sound Pressure Levels around an Outdoor Jet-Engine Test Stand.

DTIC Science & Technology

1983-06-01

60 References ........................................................... 79 AccesSqlon For NTIS rFA&I r"!’ TAU U: .,P Dist r A. -. S iv...separate exhaust nozzles for discharge of fan and turbine exhaust flows (e.g., JT15D, TFE731 , ALF-502, CF34, JT3D, CFM56, RB.211, CF6, JT9D, and PW2037...minimum radial distance from the effective source of sound at 40 Hz should then be approxi- mately 69 m. At 60 Hz, the minimum radial distance should be

Credit WCT. Photographic copy of photograph, low level aerial view ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, low level aerial view of Test Stand "D," looking due south, after completion of Dd station installation in 1961. Note Test Stand "D" "neutralization pond" to immediate southeast of tower. A steel barrier north of and parallel to the Dd station separates fuel run tanks (on south side obscured from view) from oxidizer run tanks (on north side). Small Dj injector test stand is visible to the immediate left of oxidizer run tanks; it is oriented on a northeast/southwest diagonal to the Dd test station. The large tank to the north of the oxidizer run tanks (near center bottom of view) is an oxidizer storage tank for nitrogen tetroxide. Slender tanks to the northwest of the tower (lower right of view) contain high pressure nitrogen gas. A large vertical tank at the base of the tower contains distilled water for flushing propellant lines. (JPL negative no. 384-2997-B, 12 December 1961) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

An image-guided planning system for endosseous oral implants.

PubMed

Verstreken, K; Van Cleynenbreugel, J; Martens, K; Marchal, G; van Steenberghe, D; Suetens, P

1998-10-01

A preoperative planning system for oral implant surgery was developed which takes as input computed tomographies (CT's) of the jaws. Two-dimensional (2-D) reslices of these axial CT slices orthogonal to a curve following the jaw arch are computed and shown together with three-dimensional (3-D) surface rendered models of the bone and computer-aided design (CAD)-like implant models. A technique is developed for scanning and visualizing an eventual existing removable prosthesis together with the bone structures. Evaluation of the planning done with the system shows a difference between 2-D and 3-D planning methods. Validation studies measure the benefits of the 3-D approach by comparing plans made in 2-D mode only with those further adjusted using the full 3-D visualization capabilities of the system. The benefits of a 3-D approach are then evident where a prosthesis is involved in the planning. For the majority of the patients, clinically important adjustments and optimizations to the 2-D plans are made once the 3-D visualization is enabled, effectively resulting in a better plan. The alterations are related to bone quality and quantity (p < 0.05), biomechanics (p < 0.005), and esthetics (p < 0.005), and are so obvious that the 3-D plan stands out clearly (p < 0.005). The improvements often avoid complications such as mandibular nerve damage, sinus perforations, fenestrations, or dehiscences.

Engine component improvement: Performance improvement, JT9D-7 3.8 AR fan

NASA Technical Reports Server (NTRS)

Gaffin, W. O.

1980-01-01

A redesigned, fuel efficient fan for the JT9D-7 engine was tested. Tests were conducted to determine the effect of the 3.8 AR fan on performance, stability, operational characteristics, and noise of the JT9D-7 engine relative to the current 4.6 AR Bill-of-Material fan. The 3.8 AR fan provides increased fan efficiency due to a more advanced blade airfoil with increased chord, eliminating one part span shroud and reducing the number of fan blades and fan exit guide vanes. Engine testing at simulated cruise conditions demonstrated the predicted 1.3 percent improvement in specific fuel consumption with the redesigned 3.8 AR fan. Flight testing and sea level stand engine testing demonstrated exhaust gas temperature margins, fan and low pressure compressor stability, operational suitability, and noise levels comparable to the Bill-of-Material fan.

28. HISTORIC VIEW OF A3 ROCKET IN TEST STAND NO. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

28. HISTORIC VIEW OF A-3 ROCKET IN TEST STAND NO. 3 AT KUMMERSDORF (THE LARGEST TEST STAND AT KUMMERSDORF). THE STAND WAS MOBILE, SINCE IT MOVED ALONG RAILS. - Marshall Space Flight Center, Redstone Rocket (Missile) Test Stand, Dodd Road, Huntsville, Madison County, AL

Effect of castration timing and oral meloxicam administration on growth performance, inflammation, behavior, and carcass quality of beef calves.

PubMed

Brown, A C; Powell, J G; Kegley, E B; Gadberry, M S; Reynolds, J L; Hughes, H D; Carroll, J A; Burdick Sanchez, N C; Thaxton, Y V; Backes, E A; Richeson, J T

2015-05-01

Beef bull calves (n = 62) were assigned randomly, within sire breed, to 1 of 4 treatments at birth. Treatments were 1) surgical castration near birth, 2) surgical castration near birth with oral administration of meloxicam (1 mg/kg BW), 3) surgical castration at weaning (WNG), or 4) surgical castration at weaning with oral administration of meloxicam (1 mg/kg BW; WMX). A subset of calves (n = 7/treatment group) were selected randomly near birth for blood collection, behavioral analyses, and rectal temperature (RT) records for a 7-d postcastration period on d 0 (birth), 1, 3, and 7, and on d 214 (weaning), 214 + 6 h, 215, 217, 221, and 228. Calf standing and lying activity were monitored from the same subsets by recording x- and y-axis positions of an accelerometer attached to the right metatarsus for 7 d postcastration. Calf BW was recorded throughout the entire production cycle, and carcass data were collected at slaughter. For statistical analyses, bulls left intact at birth were considered a positive control (BUL) for observations that occurred before their treatment application at weaning; likewise, bulls castrated at birth were considered a negative control (STR) during postweaning observations. No difference (P > 0.88) occurred in ADG between treatments throughout the preweaning period (d 0 to 214); however, 56-d postweaning ADG was greatest ( P= 0.02) in STR, intermediate in WMX, and least in WNG. At weaning, haptoglobin (Hp) was greater (P ≤ 0.005) for WNG and WMX compared to STR on d 214+6 h, 215, and 217, and Hp was greater (P = 0.05) in WNG compared to WMX on d 217. Neutrophils increased (P < 0.001) and red blood cells decreased (P ≤ 0.03) for WNG and WMX on d 214+6 h and 217, respectively. Postweaning behavior observations indicated that STR calves spent the least proportion of time standing (P = 0.002) when compared to WNG and WMX. Furthermore, WMX calves exhibited a greater proportion of time spent standing (P = 0.03) compared to WNG. Grazing and finishing phase ADG and carcass measurements did not differ (P ≥ 0.24) across treatments. In this study, surgical castration at weaning, but not near birth, altered the acute phase response, behavior, and growth performance. Oral meloxicam reduced serum Hp and improved ADG briefly when administered to calves castrated at weaning. Oral administration of meloxicam may be efficacious for mitigating some of the stress and inflammation associated with castration of weaning-age bull calves.

High resolution, wide field of view, real time 340GHz 3D imaging radar for security screening

NASA Astrophysics Data System (ADS)

Robertson, Duncan A.; Macfarlane, David G.; Hunter, Robert I.; Cassidy, Scott L.; Llombart, Nuria; Gandini, Erio; Bryllert, Tomas; Ferndahl, Mattias; Lindström, Hannu; Tenhunen, Jussi; Vasama, Hannu; Huopana, Jouni; Selkälä, Timo; Vuotikka, Antti-Jussi

2017-05-01

The EU FP7 project CONSORTIS (Concealed Object Stand-Off Real-Time Imaging for Security) is developing a demonstrator system for next generation airport security screening which will combine passive and active submillimeter wave imaging sensors. We report on the development of the 340 GHz 3D imaging radar which achieves high volumetric resolution over a wide field of view with high dynamic range and a high frame rate. A sparse array of 16 radar transceivers is coupled with high speed mechanical beam scanning to achieve a field of view of 1 x 1 x 1 m3 and a 10 Hz frame rate.

Vision-Based 3D Motion Estimation for On-Orbit Proximity Satellite Tracking and Navigation

DTIC Science & Technology

2015-06-01

Multiple-Purpose Crew Vehicle (MPVC), which will be provided with a LIDAR sensor as primary relative navigation system [26, 33, 34]. A drawback of LIDAR...328–352, 2009. [63] C. Luigini and M. Romano, “A ballistic- pendulum test stand to characterize small cold-gas thruster nozzles,” Acta

Thinning sprout clumps

Treesearch

Richard M. Godman

1992-01-01

How do you deal with stump sprouts in second-growth hardwood stands? Although thinning them takes special effort to avoid causing decay, stump sprouts are the only way to regenerate certain species such as basswood. Generally, you should thin them early and preferably when potential crop stems are 3 inches d.b.h. or less. But if you delay thinning until they are pole-...

Association of standing and lying behavior patterns and incidence of intramammary infection in dairy cows milked with an automatic milking system.

PubMed

Devries, T J; Deming, J A; Rodenburg, J; Seguin, G; Leslie, K E; Barkema, H W

2011-08-01

The standing and lying behavior patterns of dairy cows, particularly the length of time cows spend standing after milking, have the potential to influence the incidence of intramammary infection (IMI). The objectives were to describe the standing and lying behavior patterns of cows milked with an automatic milking system (AMS) and to determine how these patterns relate to the incidence of IMI. One hundred and eleven lactating Holstein dairy cows were monitored over a 4-mo period. These cows were kept in a sand-bedded freestall barn with 2 pens, each with a free cow traffic AMS. Feed was delivered once daily, and pushed up 2 to 3 times daily. Quarter milk samples were collected for bacteriological culture from each cow once every 4 wk. A new IMI was defined as a positive culture sample following a negative culture. For 7 d before each of the last 3 milk samplings, standing and lying behavior, and times of milking and feed manipulation (feed delivery and push up) were recorded. Daily lying time and lying bout length were negatively related with milk yield (r=-0.23 and -0.20, respectively) and milking frequency (r=-0.32 and -0.20, respectively); milk yield was positively related to milking frequency (r=0.58). Feed manipulation near the time cows were milked (1h before 2h after) resulted in the longest post-milking standing times (mean=86 min; 95% confidence interval=78, 94 min), whereas feed manipulation occurring outside that time frame resulted in shorter post-milking standing times. Over the study period, 171 new IMI were detected. Of these new IMI detected, those caused by coagulase-negative staphylococci were the only ones associated with post-milking standing time; as post-milking standing time increased past 2.5h after milking, the odds of acquiring a new IMI tended to also increase. In summary, standing and lying behavior patterns of cows milked with an AMS were affected by both feed manipulation and their milking activity. Further, the post-milking standing time of cows milked with an AMS can be managed by providing fresh feed, as well as by pushing up feed, frequently throughout the day. Finally, cows that spend long periods of time (>2.5h) standing following milking may be at higher risk of acquiring a new CNS IMI. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Mechanically Robust, Ultraelastic Hierarchical Foam with Tunable Properties via 3D Printing

DOE PAGES

Chen, Qiyi; Cao, Peng-Fei; Advincula, Rigoberto C.

2018-04-11

We present a mechanically robust, ultraelastic foam with controlled multiscale architectures and tunable mechanical/conductive performance is fabricated via 3D printing. Hierarchical porosity, including both macro- and microscaled pores, are produced by the combination of direct ink writing (DIW), acid etching, and phase inversion. The thixotropic inks in DIW are formulated by a simple one-pot process to disperse duo nanoparticles (nanoclay and silica nanoparticles) in a polyurethane suspension. The resulting lightweight foam exhibits tailorable mechanical strength, unprecedented elasticity (standing over 1000 compression cycles), and remarkable robustness (rapidly and fully recover after a load more than 20 000 times of its ownmore » weight). Surface coating of carbon nanotubes yields a conductive elastic foam that can be used as piezoresistivity sensor with high sensitivity. For the first time, this strategy achieves 3D printing of elastic foam with controlled multilevel 3D structures and mechanical/conductive properties. In conclusion, the facile ink preparation method can be utilized to fabricate foams of various materials with desirable performance via 3D printing.« less

A Pipeline for 3D Digital Optical Phenotyping Plant Root System Architecture

NASA Astrophysics Data System (ADS)

Davis, T. W.; Shaw, N. M.; Schneider, D. J.; Shaff, J. E.; Larson, B. G.; Craft, E. J.; Liu, Z.; Kochian, L. V.; Piñeros, M. A.

2017-12-01

This work presents a new pipeline for digital optical phenotyping the root system architecture of agricultural crops. The pipeline begins with a 3D root-system imaging apparatus for hydroponically grown crop lines of interest. The apparatus acts as a self-containing dark room, which includes an imaging tank, motorized rotating bearing and digital camera. The pipeline continues with the Plant Root Imaging and Data Acquisition (PRIDA) software, which is responsible for image capturing and storage. Once root images have been captured, image post-processing is performed using the Plant Root Imaging Analysis (PRIA) command-line tool, which extracts root pixels from color images. Following the pre-processing binarization of digital root images, 3D trait characterization is performed using the next-generation RootReader3D software. RootReader3D measures global root system architecture traits, such as total root system volume and length, total number of roots, and maximum rooting depth and width. While designed to work together, the four stages of the phenotyping pipeline are modular and stand-alone, which provides flexibility and adaptability for various research endeavors.

Mechanically Robust, Ultraelastic Hierarchical Foam with Tunable Properties via 3D Printing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Qiyi; Cao, Peng-Fei; Advincula, Rigoberto C.

We present a mechanically robust, ultraelastic foam with controlled multiscale architectures and tunable mechanical/conductive performance is fabricated via 3D printing. Hierarchical porosity, including both macro- and microscaled pores, are produced by the combination of direct ink writing (DIW), acid etching, and phase inversion. The thixotropic inks in DIW are formulated by a simple one-pot process to disperse duo nanoparticles (nanoclay and silica nanoparticles) in a polyurethane suspension. The resulting lightweight foam exhibits tailorable mechanical strength, unprecedented elasticity (standing over 1000 compression cycles), and remarkable robustness (rapidly and fully recover after a load more than 20 000 times of its ownmore » weight). Surface coating of carbon nanotubes yields a conductive elastic foam that can be used as piezoresistivity sensor with high sensitivity. For the first time, this strategy achieves 3D printing of elastic foam with controlled multilevel 3D structures and mechanical/conductive properties. In conclusion, the facile ink preparation method can be utilized to fabricate foams of various materials with desirable performance via 3D printing.« less

3D Reconstruction of Static Human Body with a Digital Camera

NASA Astrophysics Data System (ADS)

Remondino, Fabio

2003-01-01

Nowadays the interest in 3D reconstruction and modeling of real humans is one of the most challenging problems and a topic of great interest. The human models are used for movies, video games or ergonomics applications and they are usually created with 3D scanner devices. In this paper a new method to reconstruct the shape of a static human is presented. Our approach is based on photogrammetric techniques and uses a sequence of images acquired around a standing person with a digital still video camera or with a camcorder. First the images are calibrated and orientated using a bundle adjustment. After the establishment of a stable adjusted image block, an image matching process is performed between consecutive triplets of images. Finally the 3D coordinates of the matched points are computed with a mean accuracy of ca 2 mm by forward ray intersection. The obtained point cloud can then be triangulated to generate a surface model of the body or a virtual human model can be fitted to the recovered 3D data. Results of the 3D human point cloud with pixel color information are presented.

Morphological Evolution of Vertically Standing Molybdenum Disulfide Nanosheets by Chemical Vapor Deposition.

PubMed

Zhang, Song; Liu, Jiajia; Ruiz, Karla Hernandez; Tu, Rong; Yang, Meijun; Li, Qizhong; Shi, Ji; Li, Haiwen; Zhang, Lianmeng; Goto, Takashi

2018-04-20

In this study, we demonstrated the chemical vapor deposition (CVD) of vertically standing molybdenum disulfide (MoS₂) nanosheets, with an unconventional combination of molybdenum hexacarbonyl (Mo(CO)₆) and 1,2-ethanedithiol (C₂H₆S₂) as the novel kind of Mo and S precursors respectively. The effect of the distance between the precursor’s outlet and substrates (denoted as d ) on the growth characteristics of MoS₂, including surface morphology and nanosheet structure, was investigated. Meanwhile, the relationship between the structure characteristics of MoS₂ nanosheets and their catalytic performance for hydrogen evolution reaction (HER) was elucidated. The formation of vertically standing nanosheets was analyzed and verified by means of an extrusion growth model. The crystallinity, average length, and average depth between peak and valley ( R z) of MoS₂ nanosheets differed depending on the spatial location of the substrate. Good crystalized MoS₂ nanosheets grown at d = 5.5 cm with the largest average length of 440 nm, and the highest R z of 162 nm contributed to a better HER performance, with a respective Tafel slope and exchange current density of 138.9 mV/decade, and 22.6 μA/cm² for raw data (127.8 mV/decade and 19.3 μA/cm² for iR-corrected data).

Standing wave contributions to the linear interference effect in stratosphere-troposphere coupling

NASA Astrophysics Data System (ADS)

Watt-Meyer, Oliver; Kushner, Paul

2014-05-01

A body of literature by Hayashi and others [Hayashi 1973, 1977, 1979; Pratt, 1976] developed a decomposition of the wavenumber-frequency spectrum into standing and travelling waves. These techniques directly decompose the power spectrum—that is, the amplitudes squared—into standing and travelling parts. This, incorrectly, does not allow for a term representing the covariance between these waves. We propose a simple decomposition based on the 2D Fourier transform which allows one to directly compute the variance of the standing and travelling waves, as well as the covariance between them. Applying this decomposition to geopotential height anomalies in the Northern Hemisphere winter, we show the dominance of standing waves for planetary wavenumbers 1 through 3, especially in the stratosphere, and that wave-1 anomalies have a significant westward travelling component in the high-latitude (60N to 80N) troposphere. Variations in the relative zonal phasing between a wave anomaly and the background climatological wave pattern—the "linear interference" effect—are known to explain a large part of the planetary wave driving of the polar stratosphere in both hemispheres. While the linear interference effect is robust across observations, models of varying degrees of complexity, and in response to various types of perturbations, it is not well understood dynamically. We use the above-described decomposition into standing and travelling waves to investigate the drivers of linear interference. We find that the linear part of the wave activity flux is primarily driven by the standing waves, at all vertical levels. This can be understood by noting that the longitudinal positions of the antinodes of the standing waves are typically close to being aligned with the maximum and minimum of the background climatology. We discuss implications for predictability of wave activity flux, and hence polar vortex strength variability.

A Meta-Analytic Review of Stand-Alone Interventions to Improve Body Image

PubMed Central

Alleva, Jessica M.; Sheeran, Paschal; Webb, Thomas L.; Martijn, Carolien; Miles, Eleanor

2015-01-01

Objective Numerous stand-alone interventions to improve body image have been developed. The present review used meta-analysis to estimate the effectiveness of such interventions, and to identify the specific change techniques that lead to improvement in body image. Methods The inclusion criteria were that (a) the intervention was stand-alone (i.e., solely focused on improving body image), (b) a control group was used, (c) participants were randomly assigned to conditions, and (d) at least one pretest and one posttest measure of body image was taken. Effect sizes were meta-analysed and moderator analyses were conducted. A taxonomy of 48 change techniques used in interventions targeted at body image was developed; all interventions were coded using this taxonomy. Results The literature search identified 62 tests of interventions (N = 3,846). Interventions produced a small-to-medium improvement in body image (d + = 0.38), a small-to-medium reduction in beauty ideal internalisation (d + = -0.37), and a large reduction in social comparison tendencies (d + = -0.72). However, the effect size for body image was inflated by bias both within and across studies, and was reliable but of small magnitude once corrections for bias were applied. Effect sizes for the other outcomes were no longer reliable once corrections for bias were applied. Several features of the sample, intervention, and methodology moderated intervention effects. Twelve change techniques were associated with improvements in body image, and three techniques were contra-indicated. Conclusions The findings show that interventions engender only small improvements in body image, and underline the need for large-scale, high-quality trials in this area. The review identifies effective techniques that could be deployed in future interventions. PMID:26418470

Test-retest reliability of sensor-based sit-to-stand measures in young and older adults.

PubMed

Regterschot, G Ruben H; Zhang, Wei; Baldus, Heribert; Stevens, Martin; Zijlstra, Wiebren

2014-01-01

This study investigated test-retest reliability of sensor-based sit-to-stand (STS) peak power and other STS measures in young and older adults. In addition, test-retest reliability of the sensor method was compared to test-retest reliability of the Timed Up and Go Test (TUGT) and Five-Times-Sit-to-Stand Test (FTSST) in older adults. Ten healthy young female adults (20-23 years) and 31 older adults (21 females; 73-94 years) participated in two assessment sessions separated by 3-8 days. Vertical peak power was assessed during three (young adults) and five (older adults) normal and fast STS trials with a hybrid motion sensor worn on the hip. Older adults also performed the FTSST and TUGT. The average sensor-based STS peak power of the normal STS trials and the average sensor-based STS peak power of the fast STS trials showed excellent test-retest reliability in young adults (intra-class correlation (ICC)≥0.90; zero in 95% confidence interval of mean difference between test and retest (95%CI of D); standard error of measurement (SEM)≤6.7% of mean peak power) and older adults (ICC≥0.91; zero in 95%CI of D; SEM≤9.9%). Test-retest reliability of sensor-based STS peak power and TUGT (ICC=0.98; zero in 95%CI of D; SEM=8.5%) was comparable in older adults, test-retest reliability of the FTSST was lower (ICC=0.73; zero outside 95%CI of D; SEM=14.4%). Sensor-based STS peak power demonstrated excellent test-retest reliability and may therefore be useful for clinical assessment of functional status and fall risk. Copyright © 2014 Elsevier B.V. All rights reserved.

Facilitated charge transport in ternary interconnected electrodes for flexible supercapacitors with excellent power characteristics

NASA Astrophysics Data System (ADS)

Chen, Wanjun; He, Yongmin; Li, Xiaodong; Zhou, Jinyuan; Zhang, Zhenxing; Zhao, Changhui; Gong, Chengshi; Li, Shuankui; Pan, Xiaojun; Xie, Erqing

2013-11-01

Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems.Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems. Electronic supplementary information (ESI) available: Additional experimental details; calculations of the specific capacitances, and energy and power densities; additional SEM and optical images; XPS results; additional electrochemical results. See DOI: 10.1039/c3nr03923d

What matters most? Evidence-based findings of health dimensions affecting the societal preferences for EQ-5D health states.

PubMed

Andrade, Monica Viegas; Noronha, Kenya Valeria Micaela de Souza; Maia, Ana Carolina; Kind, Paul

2013-11-01

This study analyzes how different health dimensions defined by the EQ-5D-3L instrument affect average individual preferences for health states. This analysis is an important benchmark for the incorporation of health technologies as it takes into consideration Brazilian population preferences in health resource allocation decisions. The EQ-5D instrument defines health in terms of five dimensions (mobility, daily activities, self-care activities, pain/discomfort, and anxiety/depression) each divided into three levels of severity. Data came from a valuation study with 3,362 literate individuals aged between 18 and 64 living in urban areas of Minas Gerais State, Brazil. The main results reveal that health utility decreases as the level of severity increases. With regard to health issues, mobility stands out as the most important EQ-5D dimension. Independently of severity levels of the other EQ-5D-3L dimensions, the highest decrements in utilities are associated with severe mobility problems.

Laser-directed 3D assembly of carbon nanotubes using two-photon polymerization (Conference Presentation)

NASA Astrophysics Data System (ADS)

Liu, Ying; Xiong, Wei; Jiang, Li Jia; Zhou, Yunshen; Li, Dawei; Jiang, Lan; Silvain, Jean-Francois; Lu, Yongfeng

2017-02-01

Precise assembly of carbon nanotubes (CNTs) in arbitrary 3D space with proper alignment is critically important and desirable for CNT applications but still remains as a long-standing challenge. Using the two-photon polymerization (TPP) technique, it is possible to fabricate 3D micro/nanoscale CNT/polymer architectures with proper CNT alignments in desired directions, which is expected to enable a broad range of applications of CNTs in functional devices. To unleash the full potential of CNTs, it is strategically important to develop TPP-compatible resins with high CNT concentrations for precise assembly of CNTs into 3D micro/nanostructures for functional device applications. We investigated a thiol grafting method in functionalizing multiwalled carbon nanotubes (MWNTs) to develop TPP-compatible MWNT-thiol-acrylate (MTA) composite resins. The composite resins developed had high MWNT concentrations up to 0.2 wt%, over one order of magnitude higher than previously published work. Significantly enhanced electrical and mechanical properties of the 3D micro/nanostructures were achieved. Precisely controlled MWNT assembly and strong anisotropic effects were confirmed. Microelectronic devices made of the MTA composite polymer were demonstrated. The nanofabrication method can achieve controlled assembly of MWNTs in 3D micro/nanostructures, enabling a broad range of CNT applications, including 3D electronics, integrated photonics, and micro/nanoelectromechanical systems (MEMS/NEMS).

Human body area factors for radiation exchange analysis: standing and walking postures

NASA Astrophysics Data System (ADS)

Park, Sookuk; Tuller, Stanton E.

2011-09-01

Effective radiation area factors ( f eff) and projected area factors ( f p) of unclothed Caucasians' standing and walking postures used in estimating human radiation exchange with the surrounding environment were determined from a sample of adults in Canada. Several three-dimensional (3D) computer body models were created for standing and walking postures. Only small differences in f eff and f p values for standing posture were found between gender (male or female) and body type (normal- or over-weight). Differences between this study and previous studies were much larger: ≤0.173 in f p and ≤0.101 in f eff. Directionless f p values for walking posture also had only minor differences between genders and positions in a stride. However, the differences of mean directional f p values of the positions dependent on azimuth angles were large enough, ≤0.072, to create important differences in modeled radiation receipt. Differences in f eff values were small: 0.02 between the normal-weight male and female models and up to 0.033 between positions in a stride. Variations of directional f p values depending on solar altitudes for walking posture were narrower than those for standing posture. When both standing and walking postures are considered, the mean f eff value, 0.836, of standing (0.826) and walking (0.846) could be used. However, f p values should be selected carefully because differences between directional and directionless f p values were large enough that they could influence the estimated level of human thermal sensation.

Effects of thinning a 55-year-old western white pine stand

Treesearch

Marvin W. Foiles

1956-01-01

The first experiment in thinning western white pine (Pinus monticola Dougl.) was planned and established by J. A. Larson and D. R. Brewster in 1914 in a 55-year-old stand on the Priest River Experimental Forest, Idaho. It was designed to compare the effects of three thinning treatments on volume and quality growth, and on total volume production with an unthinned stand...

Stemwood production patterns in ponderosa pine: effects of stand dynamics and other factors

Treesearch

Michael J. Arbaugh; David L. Peterson

1993-01-01

Growth patterns of vertical stems in nine ponderosa pines from a stand in the southern Sierra Nevada were analyzed for recent changes due to stand dominance position, age, climate, and ozone exposure. Large positive correlations were found between increments in volume growth and basal area at d.b.h. The results indicated that patterns of wood distribution along the...

Snag densities in old-growth stands on the Gasquet Ranger District, Six Rivers National Forest, California

Treesearch

Thomas M. Jimerson

1989-01-01

Baseline levels for densities of snags (standing dead trees) wered etermined in undisturbed old-growth stands on the Gasquet Ranger District. Six Riven National Forest, California. Snag species, number, diameter at breast height (d.b.h.), height, cavity type, cavity use, decay class, and snag origin were recorded on 317 plots over a 2-year period. The 2121 snags...

Growth patterns of Tsuga canadensis in managed uneven-aged northern conifer stands

Treesearch

Laura S. Kenefic; Robert S. Seymour

2000-01-01

This study reports patterns of regeneration and growth for 100 eastern hemlock (Tsuga canadensis (L.) Carr.) up to 20 inches (50 cm) dbh in two mixed-species selection stands on the Penobscot Experimental Forest in east-central Maine. The study stands are part of a U.S.D.A. Forest Service experiment in which eastern hemlock has remained stable over a...

Cone Characteristics and Seed Quality 10 Years After An Uneven-Aged Regeneration Cut In Shortleaf Pine Stands

Treesearch

Kenneth J. Grayson; Robert F. Wittwer; Michael G. Shelton

2002-01-01

Cone characteristics and seed quality for 16 released (stand density 14 square meters per hectare) and 16 unreleased (stand density 28 square meters per hectare) shortleaf pine (Pinus echinata Mill.) trees were described by d.b.h. class (28, 33, 38, 43 centimeters) and crown position (upper south, upper north, lower south, and lower north). The 38-...

Design and validation of a portable, inexpensive and multi-beam timing light system using the Nintendo Wii hand controllers.

PubMed

Clark, Ross A; Paterson, Kade; Ritchie, Callan; Blundell, Simon; Bryant, Adam L

2011-03-01

Commercial timing light systems (CTLS) provide precise measurement of athletes running velocity, however they are often expensive and difficult to transport. In this study an inexpensive, wireless and portable timing light system was created using the infrared camera in Nintendo Wii hand controllers (NWHC). System creation with gold-standard validation. A Windows-based software program using NWHC to replicate a dual-beam timing gate was created. Firstly, data collected during 2m walking and running trials were validated against a 3D kinematic system. Secondly, data recorded during 5m running trials at various intensities from standing or flying starts were compared to a single beam CTLS and the independent and average scores of three handheld stopwatch (HS) operators. Intraclass correlation coefficient and Bland-Altman plots were used to assess validity. Absolute error quartiles and percentage of trials in absolute error threshold ranges were used to determine accuracy. The NWHC system was valid when compared against the 3D kinematic system (ICC=0.99, median absolute error (MAR)=2.95%). For the flying 5m trials the NWHC system possessed excellent validity and precision (ICC=0.97, MAR<3%) when compared with the CTLS. In contrast, the NWHC system and the HS values during standing start trials possessed only modest validity (ICC<0.75) and accuracy (MAR>8%). A NWHC timing light system is inexpensive, portable and valid for assessing running velocity. Errors in the 5m standing start trials may have been due to erroneous event detection by either the commercial or NWHC-based timing light systems. Copyright © 2010 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Efficacy of "Verbenone Plus" for protecting ponderosa pine trees and stands from Dendroctonus brevicomis (Coleoptera: Curculionidae) attack in British Columbia and California.

PubMed

Fettig, Christopher J; McKelvey, Stephen R; Dabney, Christopher P; Huber, Dezene P W; Lait, Cameron G; Fowler, Donald L; Borden, John H

2012-10-01

The western pine beetle, Dendroctonus brevicomis LeConte (Coleoptera: Curculionidae, Scolytinae), is a major cause of ponderosa pine, Pinus ponderosa Douglas ex Lawson, mortality in much of western North America. We review several years of research that led to the identification of Verbenone Plus, a novel four-component semiochemcial blend [acetophenone, (E)-2-hexen-1-ol + (Z)-2-hexen-1-ol, and (-)-verbenone] that inhibits the response of D. brevicomis to attractant-baited traps, and examine the efficacy of Verbenone Plus for protecting individual trees and forest stands from D. brevicomis infestations in British Columbia and California. In all experiments, semiochemicals were stapled around the bole of treated trees at approximately equal to 2 m in height. (-)-Verbenone alone had no effect on the density of total attacks and successful attacks by D. brevicomis on attractant-baited P. ponderosa, but significantly increased the percentage of pitchouts (unsuccessful D. brevicomis attacks). Verbenone Plus significantly reduced the density of D. brevicomis total attacks and D. brevicomis successful attacks on individual trees. A significantly higher percentage of pitchouts occurred on Verbenone Plus-treated trees. The application of Verbenone Plus to attractant-baited P. ponderosa significantly reduced levels of tree mortality. In stand protection studies, Verbenone Plus significantly reduced the percentage of trees mass attacked by D. brevicomis in one study, but in a second study no significant treatment effect was observed. Future research should concentrate on determining optimal release rates and spacings of release devices in stand protection studies, and expansion of Verbenone Plus into other systems where verbenone alone has not provided adequate levels of tree protection.

Phytoextraction of Cd-contaminated soil by carambola (Averrhoa carambola) in field trials.

PubMed

Li, J T; Liao, B; Dai, Z Y; Zhu, R; Shu, W S

2009-08-01

Use of metal-accumulating woody species to extract metals from heavy metal contaminated soil has received more attention. While considerable studies have focused on the phytoextraction potential of willow (Salix spp.) and poplar (Populus spp.), similar information is rare for other woody species. Carambola (Averrhoa carambola) is a high-biomass tree and has been identified as a new Cd-accumulating species. The present study aimed to evaluate the Cd phytoextraction potential of carambola under field condition. After growing in a slightly Cd-contaminated site for about 170 d, the carambola stand initiated by seed-seedling with high planting density (encoded with "HD-1yr") attained a high shoot biomass yield of 18.6 t ha(-1) and extracted 213 g Cdha(-1), resulting in a 1.6-fold higher Cd removal efficiency than that of a contrasting stand established by grafted-seedling with low planting density (5.3% vs. 2%). That is, "HD-1yr" would remove 50% of the total soil Cd with 13yr, assuming that the Cd removal efficiency would not change over time. Further, one crop of "HD-1yr" significantly decreased (63-69%) the Cd uptake by subsequent vegetables. Among the four carambola stands established using grafted-seedling, the 2-yr-old stand exhibited the highest annual Cd removal efficiency (3.7%), which was yet lower than that of "HD-1yr". These results suggested that phytoextraction of Cd by carambola (especially for "HD-1yr" stand) presented a feasible option to clean up agricultural soils slightly contaminated by Cd.

Atomic electron tomography: 3D structures without crystals

DOE PAGES

Miao, Jianwei; Ercius, Peter; Billinge, S. J. L.

2016-09-23

Crystallography has been fundamental to the development of many fields of science over the last century. However, much of our modern science and technology relies on materials with defects and disorders, and their three-dimensional (3D) atomic structures are not accessible to crystallography. One method capable of addressing this major challenge is atomic electron tomography. By combining advanced electron microscopes and detectors with powerful data analysis and tomographic reconstruction algorithms, it is now possible to determine the 3D atomic structure of crystal defects such as grain boundaries, stacking faults, dislocations, and point defects, as well as to precisely localize the 3Dmore » coordinates of individual atoms in materials without assuming crystallinity. In this work, we review the recent advances and the interdisciplinary science enabled by this methodology. We also outline further research needed for atomic electron tomography to address long-standing unresolved problems in the physical sciences.« less

Technology infusion of intellectual 3D printers-based prototyping of products into learning process

NASA Astrophysics Data System (ADS)

Boshhenko, T. V.; Chepur, P. V.

2018-03-01

The article considers the prospects for the technologies of intellectual design and prototyping applying 3D printers. It presents basic technologies of 3D printing, currently developed and released for construction. The experience of educational activities in the University to train students for the Academic Competitions on three-dimensional modeling and prototyping is described in the present article. Requirements for the prototyping implementation are given, allowing obtaining a positive effect from the technology infusion released for construction. The results of activities to train students for the Academic Competition are stated. It is established that the proposed approaches to the training of students have led to the highest score in the national contest in Novosibirsk when performing tasks for prototyping a stand for a cell phone and manufacturing the product on a 3D printer at the SLS technology, selective laser sintering. The conclusions about the possibilities and prospects of development of this direction in the industry in the entire country are drawn.

Phasor based single-molecule localization microscopy in 3D (pSMLM-3D): An algorithm for MHz localization rates using standard CPUs

NASA Astrophysics Data System (ADS)

Martens, Koen J. A.; Bader, Arjen N.; Baas, Sander; Rieger, Bernd; Hohlbein, Johannes

2018-03-01

We present a fast and model-free 2D and 3D single-molecule localization algorithm that allows more than 3 × 106 localizations per second to be calculated on a standard multi-core central processing unit with localization accuracies in line with the most accurate algorithms currently available. Our algorithm converts the region of interest around a point spread function to two phase vectors (phasors) by calculating the first Fourier coefficients in both the x- and y-direction. The angles of these phasors are used to localize the center of the single fluorescent emitter, and the ratio of the magnitudes of the two phasors is a measure for astigmatism, which can be used to obtain depth information (z-direction). Our approach can be used both as a stand-alone algorithm for maximizing localization speed and as a first estimator for more time consuming iterative algorithms.

Digit ratio (2D:4D) and physical fitness (Eurofit test battery) in school children.

PubMed

Ranson, R; Stratton, G; Taylor, S R

2015-05-01

The relative lengths of the index finger to the ring finger (2D:4D) is sexually dimorphic and is thought to be a correlate of prenatal sex steroids (low 2D:4D=high prenatal testosterone and low prenatal oestrogen). In adults there have been reports that low 2D:4D is consistently associated with high sports performance. To investigate correlations between 2D:4D and fitness levels in children. Right 2D:4D and body size were measured, in addition to flexibility, speed, endurance and strength (Eurofit tests). 922 boys and 835 girls (mean ages (years): 10.8 ± 1.01 and 10.07 ± 1.00 respectively). height, mass, BMI, triceps and subscapular skinfolds, 20 m shuttle run, sit and reach, standing broad jump, hand grip strength, 10 × 5m sprint, and the sit and reach test. Boys significantly outperformed the girls in the 10 × 5m sprints, the 20 m shuttle run, standing broad jump, and hand grip strength. In boys but not girls, 2D:4D was significantly negatively correlated with scores in all these tests except the standing broad jump. In girls but not boys, 2D:4D was significantly positively correlated to stature, mass, BMI and waist circumference. It is suggested that high prenatal testosterone and low prenatal oestrogen (low 2D:4D) is implicated in high sprinting speed, endurance and hand grip strength in boys. In girls low prenatal testosterone and high prenatal oestrogen is associated with large body size. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Unexpected Huge Dimerization Ratio in One-Dimensional Carbon Atomic Chains.

PubMed

Lin, Yung-Chang; Morishita, Shigeyuki; Koshino, Masanori; Yeh, Chao-Hui; Teng, Po-Yuan; Chiu, Po-Wen; Sawada, Hidetaka; Suenaga, Kazutomo

2017-01-11

Peierls theory predicted atomic distortion in one-dimensional (1D) crystal due to its intrinsic instability in 1930. Free-standing carbon atomic chains created in situ in transmission electron microscope (TEM)1-3 are an ideal example to experimentally observe the dimerization behavior of carbon atomic chain within a finite length. We report here a surprisingly huge distortion found in the free-standing carbon atomic chains at 773 K, which is 10 times larger than the value expected in the system. Such an abnormally distorted phase only dominates at the elevated temperatures, while two distinct phases, distorted and undistorted, coexist at lower or ambient temperatures. Atom-by-atom spectroscopy indeed shows considerable variations in the carbon 1s spectra at each atomic site but commonly observes a slightly downshifted π* peak, which proves its sp 1 bonding feature. These results suggest that the simple model, relaxed and straight, is not fully adequate to describe the realistic 1D structure, which is extremely sensitive to perturbations such as external force or boundary conditions.

Fabrication of free-standing hierarchical carbon nanofiber/graphene oxide/polyaniline films for supercapacitors.

PubMed

Xu, Dongdong; Xu, Qun; Wang, Kaixi; Chen, Jun; Chen, Zhimin

2014-01-08

A hierarchical high-performance electrode with nanoacanthine-style polyaniline (PANI) deposited onto a carbon nanofiber/graphene oxide (CNF/GO) template was successfully prepared via an in situ polymerization process. The morphology analysis shows that introducing one-dimensional (1D) CNF could significantly decrease/inhibit the staking of laminated GO to form an open-porous CNF/GO architecture. Followed with in situ facial deposition of PANI, the as-synthesized PANI modified CNF/GO exhibits three-dimensional (3D) hierarchical layered nanoarchitecture, which favors the diffusion of the electrolyte ions into the inner region of active materials. The hierarchical free-standing electrodes were directly fabricated into sandwich structured supercapacitors using 1 M H2SO4 as the electrolyte showing a significant specific capacitance of 450.2 F/g at the voltage scan rate of 10 mV/s. The electrochemical properties of the hierarchical structure can be further improved by a reduction procedure of GO before the deposition of PANI.

Peasant Protest in Kyrgyzstan: Standing Up Next to a Mountain

DTIC Science & Technology

2007-06-01

featuresarticle/2006/2/A0E19880-2D66-4263-9291-142E6A5B00D1.html (accessed June 15, 2007). 94 Amanov Taalaibek, “Kyrgyz Opposition Rally Looms...548A391224F1.html (accessed January 15, 2007); Taalaibek Amanov , “No Give and Take in Kyrgyz Stand-off,” Institute for War and Peace Reporting...2002, http://iwpr.net/?p=rca&s=f&o=177731&apc_state=henirca4796f1d50976863fd92 b4a29c882becb (accessed June 15, 2007). Amanov , Taalaibek. “Kyrgyz

Graeco-Roman Astro-Architecture: The Temples of Pompeii

NASA Astrophysics Data System (ADS)

Tiede, Vance R.

2014-01-01

Roman architect Marcus Vetruvius Pollio (ca. 75-15 BC) wrote, “[O]ne who professes himself as an architect should be…acquainted with astronomy and the theory of the heavens…. From astronomy we find the east, west, south, and north, as well as the theory of the heavens, the Equinox, Solstice and courses of the Stars.” (De Architectura Libri Decem I:i:3,10). In order to investigate the role of astronomy in temple orientation, the author conducted a preliminary GIS DEM/Satellite Imaging survey of 11 temples at Pompeii, Italy (N 40d 45', E 14d 29'). The GIS survey measured the true azimuth and horizon altitude of each temple’s major axis and was field checked by a Ground Truth survey with theodolite and GPS, 5-18 April 2013. The resulting 3D vector data was analyzed with Program STONEHENGE (Hawkins 1983, 328) to identify the local skyline declinations aligned with the temple major axes. Analysis suggests that the major axes of the temples of Apollo, Jupiter and Venus are equally as likely to have been oriented to Pompeii’s urban grid, itself oriented NW-SE on Mt. Vesuvius’ slope and hydraulic gradient to optimize urban sewer/street drainage (cf. Hodge 1992). However, the remaining nine temples appear to be oriented to astronomical targets on the local horizon associated with Graeco-Roman calendrics and mythology. TEMPLE/ DATE/ MAJOR AXIS ASTRO-TARGET (Skyline Declination in degrees) Public Lares/AD 50/ Cross-Quarter 7 Nov/3 Feb Sun Set, Last Gleam (-16.5) Vespsian/ AD 69-79/ Cross-Quarter 7 Nov/3 Feb Sun Set, LG (-16.2) Fortuna Augusta/ AD 1/ Winter Solstice Sun Set, LG (-22.9) Aesculapius/ 100 BC/ Perseus Rise (β Persei-Algol = +33.0) & Midsummer Moon Major Stand Still Set, LG (-28.1) Isis/ 100 BC/ Midwinter Moon Major Stand Still Rise, Tangent (+28.5) & Equinox Sun Set, Tangent (-0.3) Jupiter/ 150 BC/ Θ Scorpionis-Sargas Rise (-38.0) Apollo/ 550 (rebuilt 70 BC)/ α Columbae-Phact Rise (-37.1) Venus/ 150 BC (rebuilt 70 BC)/ α Columbae-Phact Rise (-37.7) Ceres/ 250 BC/ Midsummer Moon Major Stand Still Set, LG (-27.9) Dioysyus/ 250 BC/ Equinox Sun Set, LG (+0.3) Doric/ 550 BC/ β Orionis-Rigel Rise (-14.6)

Three-dimensional manipulation of single cells using surface acoustic waves

PubMed Central

Guo, Feng; Mao, Zhangming; Chen, Yuchao; Xie, Zhiwei; Lata, James P.; Li, Peng; Ren, Liqiang; Liu, Jiayang; Yang, Jian; Dao, Ming; Suresh, Subra; Huang, Tony Jun

2016-01-01

The ability of surface acoustic waves to trap and manipulate micrometer-scale particles and biological cells has led to many applications involving “acoustic tweezers” in biology, chemistry, engineering, and medicine. Here, we present 3D acoustic tweezers, which use surface acoustic waves to create 3D trapping nodes for the capture and manipulation of microparticles and cells along three mutually orthogonal axes. In this method, we use standing-wave phase shifts to move particles or cells in-plane, whereas the amplitude of acoustic vibrations is used to control particle motion along an orthogonal plane. We demonstrate, through controlled experiments guided by simulations, how acoustic vibrations result in micromanipulations in a microfluidic chamber by invoking physical principles that underlie the formation and regulation of complex, volumetric trapping nodes of particles and biological cells. We further show how 3D acoustic tweezers can be used to pick up, translate, and print single cells and cell assemblies to create 2D and 3D structures in a precise, noninvasive, label-free, and contact-free manner. PMID:26811444

Growth after thinning ponderosa and Jeffrey pine pole stands in northeastern California

Treesearch

William W. Oliver

1972-01-01

Thinning ponderosa and Jeffrey pine pole stands (6 to 8 inches d.b.h.) on Meyer Site Classes IV and V land (site index 65 to 80) stimulates growth in diameter and height. This was concluded from data on 12 thinned plots scattered over northeastern California, in natural stands and in a plantation. Basal areas immediately after thinning ranged from 13 to 149 square feet...

Cone production, seed dispersal, germination in...old-growth redwood cut and uncut stands

Treesearch

Kenneth N. Boe

1968-01-01

Records of 5 and 6 years' cone crops in old-growth redwood (Sequoia sempervirens [D. Don Endl.] stands in northern California were studied for silvical facts. They show that (a) the principal trees in both cut and uncut stands bore fair to good cone crops for 5 consecutive years, (b) maximum seed dispersal of both total and sound seed occurred in winter, (c)...

3D postural balance with regard to gravity line: an evaluation in the transversal plane on 93 patients and 23 asymptomatic volunteers

PubMed Central

Obeid, Ibrahim; Aurouer, Nicolas; Hauger, Olivier; Vital, Jean-Marc; Dubousset, Jean; Skalli, Wafa

2009-01-01

Relevance of posture assessment has been reported in case of spine disorders. This study explores the interest in quantifying posture using 3D reconstruction from biplanar X-rays in free standing position and a force plate. 93 patients consulting for spine disorders were divided (‘3D deformity’, ‘sagittal imbalance’ and ‘mild deformity’) and compared with 23 asymptomatic volunteers. Registration of the gravity line (GL) in reconstruction yielded transversal position of the center of acoustic meati (CAM) T1, T4, T9, L3, S1 and hip axis (HA) with regard to GL. Transversal position of CAM and L3 appeared as relevant parameters to discriminate patients from volunteers. Sagittal inclination of the axis linking the CAM to HA was correlated with position of the CAM to GL (r = 0.92 for patients). In conclusion, observing posture in 3D with regard to GL provides clinical relevant information. CAM-HA inclination may improve postural evaluation without force plate. PMID:20035359

In ovo feeding with minerals and vitamin D3 improves bone properties in hatchlings and mature broilers.

PubMed

Yair, R; Shahar, R; Uni, Z

2015-11-01

The objective of this study was to examine the effect of in ovo feeding (IOF) with inorganic minerals or organic minerals and vitamin D3 on bone properties and mineral consumption. Eggs were incubated and divided into 4 groups: IOF with organic minerals, phosphate, and vitamin D3 (IOF-OMD); IOF with inorganic minerals and phosphate (IOF-IM); sham; and non-treated controls (NTC). IOF was performed on embryonic day (E) 17; tibiae and yolk samples were taken on E19 and E21. Post-hatch, only chicks from the IOF-OMD, sham, and NTC were raised, and tibiae were taken on d 10 and 38. Yolk mineral content was examined by inductively coupled plasma spectroscopy. Tibiae were tested for their whole-bone mechanical properties, and mid-diaphysis bone sections were indented in a micro-indenter to determine bone material stiffness (Young's modulus). Micro-computed tomography (μCT) was used to examine cortical and trabecular bone structure. Ash content analysis was used to examine bone mineralization. A latency-to-lie (LTL) test was used to measure standing ability of the d 38 broilers. The results showed that embryos from both IOF-OMD and IOF-IM treatments had elevated Cu, Mn, and Zn amounts in the yolk on E19 and E21 and consumed more of these minerals (between E19 and E21) in comparison to the sham and NTC. On E21, these hatchlings had higher whole-bone stiffness in comparison to the NTC. On d 38, the IOF-OMD had higher ash content, elevated whole-bone stiffness, and elevated Young's modulus (in males) in comparison to the sham and NTC; however, no differences in standing ability were found. Very few structural differences were seen during the whole experiment. This study demonstrates that mineral supplementation by in ovo feeding is sufficient to induce higher mineral consumption from the yolk, regardless of its chemical form or the presence of vitamin D3. Additionally, IOF with organic minerals and vitamin D3 can increase bone ash content, as well as stiffness of the whole bone and bone material in the mature broiler, but does not lead to longer LTL. © 2015 Poultry Science Association Inc.

77 FR 38039 - Floor-Standing, Metal-Top Ironing Tables and Certain Parts Thereof From the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-26

... (Fed. Cir. 1990) (Timken), as clarified by Diamond Sawblades Mfrs. Coalition v. United States, 626 F.3d 1374 (Fed. Cir. 2010) (Diamond Sawblades), the Department is notifying the public that the final..., as clarified by Diamond Sawblades, the Federal Circuit has held that, pursuant to section 516A(e) of...

46 CFR 153.1600 - Equipment required for conducting the stripping quantity test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... container: (1) A wet vacuum. (2) A positive displacement pump. (3) An eductor with an air/water separator in... measuring the volume of water remaining in the tank to an accuracy of ±5%; (c) A squeegee or broom to collect standing water on the tank floor; (d) One or more containers for collecting and transferring water...

3D engineered fiberboard : engineering analysis of a new building product

Treesearch

John F. Hunt; Jerrold E. Winandy

2003-01-01

In many forests across the United States, the high forest fuel loadings are contributing to our recent forest fire problems. Many fire-prone timber stands are generally far from traditional timber markets or the timber is not economically valuable enough to cover the costs of removal. To help address this problem, the USDA Forest Products Laboratory has developed a...

14 CFR Appendix D to Part 121 - Criteria for Demonstration of Emergency Evacuation Procedures Under § 121.291

Code of Federal Regulations, 2010 CFR

2010-01-01

... against shining into the airplane's windows or doors. (2) The airplane must be a normal ground attitude with landing gear extended. (3) Unless the airplane is equipped with an off-wing descent means, stands... is not part of the emergency evacuation equipment of the airplane may be used to aid the participants...

Classification of Explosive Residues on Organic Substrates Using Laser Induced Breakdown Spectroscopy

DTIC Science & Technology

2013-04-01

463–512 (2007). 2. D. A. Cremers and L. J. Radziemski, Handbook of Laser- Induced Breakdown Spectroscopy (Wiley, 2006 ). 3. D. A. Cremers , “The analysis...Acta, Part B 61, 88–95 ( 2006 ). 5. C. Lopez-Moreno, S. Palanco, J. Javier Laserna, F. De Lucia, Jr., A. W. Miziolek, J. Rose, R. A. Walters and A. I...Spectrom 21, 55–60 ( 2006 ). 6. A. Ferrero and J. J. Laserna, “A theoretical study of atmo- spheric propagation of laser and return light for stand-off

Photographic copy of photograph, aerial view looking north at Jet ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph, aerial view looking north at Jet Propulsion Laboratory, Edwards Test Station complex in 1959, shortly after completion of 'D' stand construction and installation of underground tunnel system. Test stands 'A,' 'B,' 'C,' and 'D' are in view; the Control and Recording Center (Building 4221/E-22) is still under construction. (JPL negative no. 384-1917-A, 28 May 1959) - Jet Propulsion Laboratory Edwards Facility, Edwards Air Force Base, Boron, Kern County, CA

A-3 Test Stand

NASA Image and Video Library

2012-06-08

A tethered Stennis Space Center employee climbs an A-3 Test Stand ladder June 8, 2012, against the backdrop of the A-2 and B-1/B-2 stands. The new A-3 Test Stand will enable simulated high-altitude testing of next-generation rocket engines.

A-3 Test Stand

NASA Image and Video Library

2012-06-08

A tethered Stennis Space Center employee climbs an A-3 Test Stand ladded June 8, 2012, against the backdrop of the A-2 and B-1/B-2 stands. The new A-3 Test Stand will enable simulated high-altitude testing of next-generation rocket engines.

Active Structural Acoustic Control of Interior Noise on a Raytheon 1900D

NASA Technical Reports Server (NTRS)

Palumbo, Dan; Cabell, Ran; Sullivan, Brenda; Cline, John

2000-01-01

An active structural acoustic control system has been demonstrated on a Raytheon Aircraft Company 1900D turboprop airliner. Both single frequency and multi-frequency control of the blade passage frequency and its harmonics was accomplished. The control algorithm was a variant of the popular filtered-x LMS implemented in the principal component domain. The control system consisted of 21 inertial actuators and 32 microphones. The actuators were mounted to the aircraft's ring frames. The microphones were distributed uniformly throughout the interior at head height, both seated and standing. Actuator locations were selected using a combinatorial search optimization algorithm. The control system achieved a 14 dB noise reduction of the blade passage frequency during single frequency tests. Multi-frequency control of the first 1st, 2nd and 3rd harmonics resulted in 10.2 dB, 3.3 dB and 1.6 dB noise reductions respectively. These results fall short of the predictions which were produced by the optimization algorithm (13.5 dB, 8.6 dB and 6.3 dB). The optimization was based on actuator transfer functions taken on the ground and it is postulated that cabin pressurization at flight altitude was a factor in this discrepancy.

Visual Understanding of Light Absorption and Waveguiding in Standing Nanowires with 3D Fluorescence Confocal Microscopy

PubMed Central

2017-01-01

Semiconductor nanowires are promising building blocks for next-generation photonics. Indirect proofs of large absorption cross sections have been reported in nanostructures with subwavelength diameters, an effect that is even more prominent in vertically standing nanowires. In this work we provide a three-dimensional map of the light around vertical GaAs nanowires standing on a substrate by using fluorescence confocal microscopy, where the strong long-range disruption of the light path along the nanowire is illustrated. We find that the actual long-distance perturbation is much larger in size than calculated extinction cross sections. While the size of the perturbation remains similar, the intensity of the interaction changes dramatically over the visible spectrum. Numerical simulations allow us to distinguish the effects of scattering and absorption in the nanowire leading to these phenomena. This work provides a visual understanding of light absorption in semiconductor nanowire structures, which is of high interest for solar energy conversion applications. PMID:28966933

Visual Understanding of Light Absorption and Waveguiding in Standing Nanowires with 3D Fluorescence Confocal Microscopy.

PubMed

Frederiksen, Rune; Tutuncuoglu, Gozde; Matteini, Federico; Martinez, Karen L; Fontcuberta I Morral, Anna; Alarcon-Llado, Esther

2017-09-20

Semiconductor nanowires are promising building blocks for next-generation photonics. Indirect proofs of large absorption cross sections have been reported in nanostructures with subwavelength diameters, an effect that is even more prominent in vertically standing nanowires. In this work we provide a three-dimensional map of the light around vertical GaAs nanowires standing on a substrate by using fluorescence confocal microscopy, where the strong long-range disruption of the light path along the nanowire is illustrated. We find that the actual long-distance perturbation is much larger in size than calculated extinction cross sections. While the size of the perturbation remains similar, the intensity of the interaction changes dramatically over the visible spectrum. Numerical simulations allow us to distinguish the effects of scattering and absorption in the nanowire leading to these phenomena. This work provides a visual understanding of light absorption in semiconductor nanowire structures, which is of high interest for solar energy conversion applications.

Simulation studies on the standing and traveling wave thermoacoustic prime movers

NASA Astrophysics Data System (ADS)

Skaria, Mathew; Rasheed, K. K. Abdul; Shafi, K. A.; Kasthurirengan, S.; Behera, Upendra

2014-01-01

Thermoacoustic systems have been a focus of recent research due to its structural simplicity, high reliability due to absence of moving parts, and can be driven by low grade energy such as fuel, gas, solar energy, waste heat etc. There has been extensive research on both standing wave and traveling wave systems. Towards the development of such systems, simulations can be carried out by several methods such as (a) solving the energy equation, (b) enthalpy flow model, (c) DeltaEC, a free software available from LANL, USA (d) Computational Fluid Dynamics (CFD) etc. We present here the simulation studies of standing wave and traveling wave thermoacoustic prime movers using CFD and DeltaEC. The CFD analysis is carried out using Fluent 6.3.26, incorporating the necessary boundary conditions with different working fluids at different operating pressures. The results obtained by CFD are compared with those obtained using DeltaEC. Also, the CFD simulation of the thermoacoustically driven refrigerator is presented.

Space Shuttle Projects

NASA Image and Video Library

1984-09-08

The crew assigned to the STS-41G mission included (seated left to right) Jon A. McBride, pilot; mission specialists Sally K. Ride, Kathryn D. Sullivan, and David C. Leestma. Standing in the rear, left to right, are payload specialists Marc Garneau, and Paul D. Scully-Power. Launched aboard the Space Shuttle Challenger on October 5, 1984 at 7:03:00 am (EDT), the STS-41G mission marked the first flight to include two women. Sullivan was the first woman to walk in space. The crew deployed the Earth Radiation Budget Satellite (ERBS), connected the components of the Orbital Refueling System (ORS) which demonstrated the possibility of refueling satellites in orbit, and carried 3 experiments of the Office of Space Terrestrial Applications-3 (OSTA-3).

STS-41G Crew Portrait

NASA Technical Reports Server (NTRS)

1984-01-01

The crew assigned to the STS-41G mission included (seated left to right) Jon A. McBride, pilot; mission specialists Sally K. Ride, Kathryn D. Sullivan, and David C. Leestma. Standing in the rear, left to right, are payload specialists Marc Garneau, and Paul D. Scully-Power. Launched aboard the Space Shuttle Challenger on October 5, 1984 at 7:03:00 am (EDT), the STS-41G mission marked the first flight to include two women. Sullivan was the first woman to walk in space. The crew deployed the Earth Radiation Budget Satellite (ERBS), connected the components of the Orbital Refueling System (ORS) which demonstrated the possibility of refueling satellites in orbit, and carried 3 experiments of the Office of Space Terrestrial Applications-3 (OSTA-3).

2. FLAME DEFLECTOR AT RIGHT, COUNTERFORT AT CENTER, FRAGMENT OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. FLAME DEFLECTOR AT RIGHT, COUNTERFORT AT CENTER, FRAGMENT OF CONCRETE CAMERA STAND IN FOREGROUND, VIEW TOWARDS SOUTHWEST. - Glenn L. Martin Company, Titan Missile Test Facilities, Captive Test Stand D-1, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

A-3 Test Stand construction

NASA Image and Video Library

2010-10-01

An 80,000-gallon liquid hydrogen tank is placed at the A-3 Test Stand construction site on Sept. 24, 2010. The tank will provide propellant for tests of next-generation rocket engines at the stand. It will be placed upright on top of the stand, helping to increase the overall height to 300 feet. Once completed, the A-3 Test Stand will enable operators to test rocket engines at simulated altitudes of up to 100,000 feet. The A-3 stand is the first large rocket engine test structure to be built at Stennis Space Center since the 1960s.

A-3 Test Stand construction

NASA Image and Video Library

2010-09-24

A 35,000-gallon liquid oxygen tank is placed at the A-3 Test Stand construction site on Sept. 24, 2010. The tank will provide propellant for tests of next-generation rocket engines at the stand. It will be placed upright on top of the stand, helping to increase the overall height to 300 feet. Once completed, the A-3 Test Stand will enable operators to test rocket engines at simulated altitudes of up to 100,000 feet. The A-3 stand is the first large rocket engine test structure to be built at Stennis Space Center since the 1960s.

Effects of bedding quality on lying behavior of dairy cows.

PubMed

Fregonesi, J A; Veira, D M; von Keyserlingk, M A G; Weary, D M

2007-12-01

Cows prefer to spend more time lying down in free stalls with more bedding, but no research to date has addressed the effects of bedding quality. Bedding in stalls often becomes wet either from exposure to the elements or from feces and urine. The aim of this study was to test the effect of wet bedding on stall preference and use. Four groups of 6 nonlactating Holstein cows were housed in free stalls bedded daily with approximately 0.1 m of fresh sawdust. Following a 5-d adaptation period, each group of cows was tested sequentially with access to stalls with either dry or wet sawdust bedding (86.4 +/- 2.1 vs. 26.5 +/- 2.1% dry matter), each for 2 d. These no-choice phases were followed by a 2-d free-choice phase during which cows had simultaneous access to stalls containing either wet or dry bedding. Stall usage was assessed by using 24-h video recordings scanned at 10-min intervals, and responses were analyzed by using a mixed model, with group (n = 4) as the observational unit. The minimum and maximum environmental temperatures during the experiment were 3.4 +/- 2.2 and 6.8 +/- 2.5 degrees C, respectively. When cows had access only to stalls with wet bedding, they spent 8.8 +/- 0.8 h/d lying down, which increased to 13.8 +/- 0.8 h/d when stalls with dry bedding were provided. Cows spent more time standing with their front 2 hooves in the stall when provided with wet vs. dry bedding (92 +/- 10 vs. 32 +/- 10 min/d). During the free-choice phase, all cows spent more time lying down in the dry stalls, spending 12.5 +/- 0.3 h/d in the dry stalls vs. 0.9 +/- 0.3 h/ d in stalls with wet bedding. In conclusion, dairy cows show a clear preference for a dry lying surface, and they spend much more time standing outside the stall when only wet bedding is available.

Foot Modeling and Smart Plantar Pressure Reconstruction from Three Sensors

PubMed Central

Ghaida, Hussein Abou; Mottet, Serge; Goujon, Jean-Marc

2014-01-01

In order to monitor pressure under feet, this study presents a biomechanical model of the human foot. The main elements of the foot that induce the plantar pressure distribution are described. Then the link between the forces applied at the ankle and the distribution of the plantar pressure is established. Assumptions are made by defining the concepts of a 3D internal foot shape, which can be extracted from the plantar pressure measurements, and a uniform elastic medium, which describes the soft tissues behaviour. In a second part, we show that just 3 discrete pressure sensors per foot are enough to generate real time plantar pressure cartographies in the standing position or during walking. Finally, the generated cartographies are compared with pressure cartographies issued from the F-SCAN system. The results show 0.01 daN (2% of full scale) average error, in the standing position. PMID:25400713

Foot modeling and smart plantar pressure reconstruction from three sensors.

PubMed

Ghaida, Hussein Abou; Mottet, Serge; Goujon, Jean-Marc

2014-01-01

In order to monitor pressure under feet, this study presents a biomechanical model of the human foot. The main elements of the foot that induce the plantar pressure distribution are described. Then the link between the forces applied at the ankle and the distribution of the plantar pressure is established. Assumptions are made by defining the concepts of a 3D internal foot shape, which can be extracted from the plantar pressure measurements, and a uniform elastic medium, which describes the soft tissues behaviour. In a second part, we show that just 3 discrete pressure sensors per foot are enough to generate real time plantar pressure cartographies in the standing position or during walking. Finally, the generated cartographies are compared with pressure cartographies issued from the F-SCAN system. The results show 0.01 daN (2% of full scale) average error, in the standing position.

On the Usability and Usefulness of 3d (geo)visualizations - a Focus on Virtual Reality Environments

NASA Astrophysics Data System (ADS)

Çöltekin, A.; Lokka, I.; Zahner, M.

2016-06-01

Whether and when should we show data in 3D is an on-going debate in communities conducting visualization research. A strong opposition exists in the information visualization (Infovis) community, and seemingly unnecessary/unwarranted use of 3D, e.g., in plots, bar or pie charts, is heavily criticized. The scientific visualization (Scivis) community, on the other hand, is more supportive of the use of 3D as it allows `seeing' invisible phenomena, or designing and printing things that are used in e.g., surgeries, educational settings etc. Geographic visualization (Geovis) stands between the Infovis and Scivis communities. In geographic information science, most visuo-spatial analyses have been sufficiently conducted in 2D or 2.5D, including analyses related to terrain and much of the urban phenomena. On the other hand, there has always been a strong interest in 3D, with similar motivations as in Scivis community. Among many types of 3D visualizations, a popular one that is exploited both for visual analysis and visualization is the highly realistic (geo)virtual environments. Such environments may be engaging and memorable for the viewers because they offer highly immersive experiences. However, it is not yet well-established if we should opt to show the data in 3D; and if yes, a) what type of 3D we should use, b) for what task types, and c) for whom. In this paper, we identify some of the central arguments for and against the use of 3D visualizations around these three considerations in a concise interdisciplinary literature review.

Seasonal changes in Cyclobalanopsis glauca transpiration and canopy stomatal conductance and their dependence on subterranean water and climatic factors in rocky karst terrain

NASA Astrophysics Data System (ADS)

Huang, Yuqing; Li, Xiankun; Zhang, Zhongfeng; He, Chengxin; Zhao, Ping; You, Yeming; Mo, Ling

2011-05-01

SummaryThe presence of forest on south China karst is presumed to increase perennial epikarst spring flow, partly because there is adequate storage in bedrock fractures underlying the shallow soil in the forest. If true, transpiration of the ecosystem would not be strongly reduced by temperate drought if trees develop deep roots to reach the perched epikarst water. Therefore, in karst ecosystem the epikarst-soil-plant-atmosphere continuum (ESPAC) would be different from the SPAC in non-karst system. We measured transpiration and canopy conductance from a Cyclobalanopsis glauca (syn. Quercus glauca) stand on a rocky hill slope in South China during 2006-2007 by using the Granier's sap-flow method. Annual stand transpiration (836 mm y -1) accounted for 48.7% of the rainfall during the experimental year. Per month, daily stand transpiration ( E c) maximums varied between 2.1 mm d -1 in January (cool season) to 5.1 mm d -1 in July (hot season). In the driest months, September and October, E c of C. glauca was still high with maximum E c 3.82 mm d -1 and 2.96 mm d -1 respectively. Solar radiation ( PAR), vapor pressure deficiency ( VPD), and air temperature were simple influences on transpiration of C. glauca, which contributed to a quadratic power model, while soil water content ( SWC) moisture influence on transpiration was complicated, which SWC influenced E c greatly under higher VPD, but did not influence E c under low VPD. High stomatal openness occurred in C. glauca in the early morning and declined throughout the day. The relation coefficient between canopy stomatal conductance ( G c) and E c was high when VPD was more than 1.0 kPa, moderate when 0.5 kPa < VPD < 1.0 kPa, and low with VPD of less than 0.5 kPa. Under high VPD, stomatal control of transpiration is high. The pattern of seasonal change of transpiration and canopy stomatal conductance of the plant in karst regions is different from that in non-karst regions, with the stand transpiration and canopy stomatal conductance being high even during the dry season in the karst region because karst plants obtain water partially from the epikarst. With high stand transpiration and canopy stomatal conductance, karst vegetation is presumed to be the most important "pathway" for ESPAC.

Using a Standing-Tree Acoustic Tool to Identify Forest Stands for the Production of Mechanically-Graded Lumber

PubMed Central

Paradis, Normand; Auty, David; Carter, Peter; Achim, Alexis

2013-01-01

This study investigates how the use of a Hitman ST300 acoustic sensor can help identify the best forest stands to be used as supply sources for the production of Machine Stress-Rated (MSR) lumber. Using two piezoelectric sensors, the ST300 measures the velocity of a mechanical wave induced in a standing tree. Measurements were made on 333 black spruce (Picea mariana (Mill.) BSP) trees from the North Shore region, Quebec (Canada) selected across a range of locations and along a chronosequence of elapsed time since the last fire (TSF). Logs were cut from a subsample of 39 trees, and sawn into 77 pieces of 38 mm × 89 mm cross-section before undergoing mechanical testing according to ASTM standard D-4761. A linear regression model was developed to predict the static modulus of elasticity of lumber using tree acoustic velocity and stem diameter at 1.3 m above ground level (R2 = 0.41). Results suggest that, at a regional level, 92% of the black spruce trees meet the requirements of MSR grade 1650Fb-1.5E, whilst 64% and 34% meet the 2100Fb-1.8E and 2400Fb-2.0E, respectively. Mature stands with a TSF < 150 years had 11 and 18% more boards in the latter two categories, respectively, and therefore represented the best supply source for MSR lumber. PMID:23482089

An unsupervised two-stage clustering approach for forest structure classification based on X-band InSAR data - A case study in complex temperate forest stands

NASA Astrophysics Data System (ADS)

Abdullahi, Sahra; Schardt, Mathias; Pretzsch, Hans

2017-05-01

Forest structure at stand level plays a key role for sustainable forest management, since the biodiversity, productivity, growth and stability of the forest can be positively influenced by managing its structural diversity. In contrast to field-based measurements, remote sensing techniques offer a cost-efficient opportunity to collect area-wide information about forest stand structure with high spatial and temporal resolution. Especially Interferometric Synthetic Aperture Radar (InSAR), which facilitates worldwide acquisition of 3d information independent from weather conditions and illumination, is convenient to capture forest stand structure. This study purposes an unsupervised two-stage clustering approach for forest structure classification based on height information derived from interferometric X-band SAR data which was performed in complex temperate forest stands of Traunstein forest (South Germany). In particular, a four dimensional input data set composed of first-order height statistics was non-linearly projected on a two-dimensional Self-Organizing Map, spatially ordered according to similarity (based on the Euclidean distance) in the first stage and classified using the k-means algorithm in the second stage. The study demonstrated that X-band InSAR data exhibits considerable capabilities for forest structure classification. Moreover, the unsupervised classification approach achieved meaningful and reasonable results by means of comparison to aerial imagery and LiDAR data.

Using a standing-tree acoustic tool to identify forest stands for the production of mechanically-graded lumber.

PubMed

Paradis, Normand; Auty, David; Carter, Peter; Achim, Alexis

2013-03-12

This study investigates how the use of a Hitman ST300 acoustic sensor can help identify the best forest stands to be used as supply sources for the production of Machine Stress-Rated (MSR) lumber. Using two piezoelectric sensors, the ST300 measures the velocity of a mechanical wave induced in a standing tree. Measurements were made on 333 black spruce (Picea mariana (Mill.) BSP) trees from the North Shore region, Quebec (Canada) selected across a range of locations and along a chronosequence of elapsed time since the last fire (TSF). Logs were cut from a subsample of 39 trees, and sawn into 77 pieces of 38 mm × 89 mm cross-section before undergoing mechanical testing according to ASTM standard D-4761. A linear regression model was developed to predict the static modulus of elasticity of lumber using tree acoustic velocity and stem diameter at 1.3 m above ground level (R2 = 0.41). Results suggest that, at a regional level, 92% of the black spruce trees meet the requirements of MSR grade 1650Fb-1.5E, whilst 64% and 34% meet the 2100Fb-1.8E and 2400Fb-2.0E, respectively. Mature stands with a TSF < 150 years had 11 and 18% more boards in the latter two categories, respectively, and therefore represented the best supply source for MSR lumber.

Distribution of Mature Cones, Conelets, and Old Cones in Shortleaf Pine-Oak Stands an Uneven-Aged Regeneration Cut

Treesearch

Kenneth J. Grayson; Robert F. Wittwer; Michael G. Shelton

2004-01-01

Sixteen shortleaf pine trees were felled in a stand 10 years after an uneven-aged regeneration cut reduced pine basal area to 60 square feet per acre and hardwoods were controlled. Sixteen unreleased trees in an adjacent uncut pine-hardwood stand (120 square feet per acre) were felled for comparison. Sample trees were selected from four 2-inch d.b.h. classes (11, 13,...

A test of high-dose verbenone for stand-level protection of lodgepole and whitebark pine from mountain pine beetle (Coleoptera: Curculionidae: Scolytinae) attacks

Treesearch

B. J. Bentz; S. Kegley; K. Gibson; R. Their

2005-01-01

The effcacy of verbenone as a stand-level protectant against mountain pine beetle, Dendroctonus ponderosae Hopkins, attacks was tested in lodgepole and whitebark pine stands at five geographically separated sites, including three consecutive years at one site. Forty and 20 high-dose pouches, with a verbenone emission rate up to 50 mg/d per pouch, were spaced in a grid...

Optimization of Easy Atomic Force Microscope (ezAFM) Controls for Semiconductor Nanostructure Profiling

DTIC Science & Technology

2017-09-01

in the vertical (z) directions. There are several instruments controls like proportional, integral , and derivative (PID) gain as well as tip force...the PID control, where P stands for proportional gain, I stands for integral gain, and D stands for derivative gain. An additional parameter that...contributes to the scanned image quality is set point. Proportional gain is multiplied by the error to adjust controller output and integral gain sums

Write-Read 3D Patterning with a Dual-Channel Nanopipette.

PubMed

Momotenko, Dmitry; Page, Ashley; Adobes-Vidal, Maria; Unwin, Patrick R

2016-09-27

Nanopipettes are becoming extremely versatile and powerful tools in nanoscience for a wide variety of applications from imaging to nanoscale sensing. Herein, the capabilities of nanopipettes to build complex free-standing three-dimensional (3D) nanostructures are demonstrated using a simple double-barrel nanopipette device. Electrochemical control of ionic fluxes enables highly localized delivery of precursor species from one channel and simultaneous (dynamic and responsive) ion conductance probe-to-substrate distance feedback with the other for reliable high-quality patterning. Nanopipettes with 30-50 nm tip opening dimensions of each channel allowed confinement of ionic fluxes for the fabrication of high aspect ratio copper pillar, zigzag, and Γ-like structures, as well as permitted the subsequent topographical mapping of the patterned features with the same nanopipette probe as used for nanostructure engineering. This approach offers versatility and robustness for high-resolution 3D "printing" (writing) and read-out at the nanoscale.

Raman and PEELS studies of magnetron sputtered a-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, S.; Jen, T.M.; Zeng, X.

Amorphous carbon coatings (a-C, a-C:H) of less than 100 nm thick were deposited on KBr pellets and silicon wafer substrate via magnetron sputtering of graphic target in argon, argon/hydrogen and argon/nitrogen atmosphere. Parallel electron energy loss spectroscopy (PEELS) analysis was used to quantify the sp{sup 2}/sp{sup 3} bonding in carbon films. Stand-alone films of amorphous carbon were produced by sputtering onto compressed KBr pellets and then floating off in distilled water for PEELS study. Raman spectroscopy was used to measure the peak intensity ratio of D-band to that of the G-band (I{sub d}/I{sub g}). It shows that higher sp{sup 3}more » fraction often associates with Raman peak ratio I{sub d}/I{sub g}. At the same time, G-band peak position P{sub g} decreases while sp{sup 3} fraction increases.« less

Three-dimensional surface imaging system for assessing human obesity

NASA Astrophysics Data System (ADS)

Xu, Bugao; Yu, Wurong; Yao, Ming; Pepper, M. Reese; Freeland-Graves, Jeanne H.

2009-10-01

The increasing prevalence of obesity suggests a need to develop a convenient, reliable, and economical tool for assessment of this condition. Three-dimensional (3-D) body surface imaging has emerged as an exciting technology for the estimation of body composition. We present a new 3-D body imaging system, which is designed for enhanced portability, affordability, and functionality. In this system, stereo vision technology is used to satisfy the requirement for a simple hardware setup and fast image acquisition. The portability of the system is created via a two-stand configuration, and the accuracy of body volume measurements is improved by customizing stereo matching and surface reconstruction algorithms that target specific problems in 3-D body imaging. Body measurement functions dedicated to body composition assessment also are developed. The overall performance of the system is evaluated in human subjects by comparison to other conventional anthropometric methods, as well as air displacement plethysmography, for body fat assessment.

Diameter increase in second-growth Appalachian hardwood stands - a comparison of species

Treesearch

George R., Jr. Trimble

1967-01-01

A study of growth at d.b.h. among eight hardwood species after partial cutting in second-growth stands. Red oak grew fastest, followed in order by yellow-poplar, sugar maple, basswood, black cherry, white ash, beech, and chestnut oak.

A-3 Test Stand continues with test cell installation

NASA Image and Video Library

2010-07-20

Employees at Stennis Space Center continue work on the A-3 Test Stand. As shown, a section of the test cell is lifted for installation on the stand's structural steel frame. Work on the A-3 Test Stand began in 2007. It is scheduled for activation in 2012.

Growth mode and structures of magnetic Mn clusters on graphene

DOE PAGES

Liu, Xiaojie; Wang, Cai-Zhuang

2016-06-22

We present a systematic study of Mn clusters on graphene by first-principles calculations. We show that the growth of Mn on graphene follows a three-dimensional (3D) mode. Both adsorption and attachment energies show that (Mn) 3 and (Mn) 6 on graphene are energetically favorable in the size range (Mn) 1-7. Moreover, larger formation energy for Mn cluster on graphene implies the incoming Mn atoms are likely to nucleate and grow into bigger and bigger Mn clusters on graphene. The magnetic moments of (Mn) 1,5,7 on graphene are enhanced by 11%, 186%, and 26% from their values at free-standing clusters, respectively.more » By contrast, the net magnetic moment of (Mn) 2,3,4,6 on graphene is reduced from that of the corresponding free-standing clusters. The origin of the magnetic moment changes can be attributed to the charge transfer within the Mn clusters and between the clusters and graphene upon adsorption.« less

Effects of flooring and restricted freestall access on behavior and claw health of dairy heifers.

PubMed

Ouweltjes, W; van der Werf, J T N; Frankena, K; van Leeuwen, J L

2011-02-01

Claw health, locomotion, feed intake, milk yield, body weight, activity, and lying and standing behavior of dairy heifers were monitored in a single dairy herd during the first 3 mo after calving. During the first 8 wk after calving, 2 treatments were applied: restricted freestall access by closing the stalls between 2300 h and 0500 h (yes or no) and alley flooring (concrete or rubber topped slatted floors). Apart from treatments, housing was identical. The animals were kept in small groups (n=4 to 6) in adjacent barn pens. Thereafter, the animals were kept in 1 group in a freestall section with concrete slatted floor and unrestricted access to the stalls for 5 wk. All animals were fed the same partial mixed ration. We hypothesized that (1) hard flooring causes high mechanical load of the claws and (2) restricted freestall access causes prolonged standing bouts and reinforced effects of hard flooring on claws. The heifers had only minor claw lesions before first calving, and the prevalence and severity of sole hemorrhages increased during the first 3 mo after calving (from 0.24 ± 0.08 to 1.18 ± 0.14 and from 0.04 ± 0.01 to 0.24 ± 0.02, respectively), particularly in the outer hind claws. Animals kept on rubber alley flooring had lower average hemorrhage scores in wk 9 (0.13 ± 0.03 vs. 0.21 ± 0.03) and wk 14 (0.20 ± 0.03 vs. 0.27 ± 0.03) after calving, had a slower feed intake (3.05 ± 0.14 vs. 3.46 ± 0.14 g/s) and spent more time feeding (7.3 ± 0.3 vs. 6.6 ± 0.3 min/h) than animals kept on hard concrete alley floors. Restricted freestall access resulted in fewer standing bouts per day (14.4 ± 1.0 vs. 17.9 ± 1.0) and more strides per hour (99.8 ± 5.4 vs. 87.2 ± 5.4) without changing overall standing time (15.0 ± 0.3 vs. 14.7 ± 0.3 h/d) and did not affect the occurrence of sole hemorrhages. The animals with no overnight freestall access spent more time standing (55.9 ± 0.9 vs. 35.8 ± 0.9 min/h) and feeding (7.8 ± 0.3 vs. 4.3 ± 0.3 min/h) between 2300 and 0500 h and less during the rest of the 24-h period (31.3 ± 0.8 vs. 37.0 ± 0.8 min/h and 6.8 ± 0.3 vs. 7.6 ± 0.3 min/h). Thus, the animals adapted to restricted freestall access, that caused increased overnight standing, by additional lying down during the day and used part of the extra standing time at night for feeding. The restrictions probably had only a minor effect on the mechanical load of their claws. Therefore, the first part of the hypothesis was confirmed and the second part was rejected. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

ARGon{sup 3}: ''3D appearance robot-based gonioreflectometer'' at PTB

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoepe, A.; Atamas, T.; Huenerhoff, D.

At the Physikalisch-Technische Bundesanstalt, the National Metrology Institute of Germany, a new facility for measuring visual appearance-related quantities has been built up. The acronym ARGon{sup 3} stands for ''3D appearance robot-based gonioreflectometer''. Compared to standard gonioreflectometers, there are two main new features within this setup. First, a photometric luminance camera with a spatial resolution of 28 {mu}m on the device under test (DUT) enables spatially high-resolved measurements of luminance and color coordinates. Second, a line-scan CCD-camera mounted to a spectrometer provides measurements of the radiance factor, respectively the bidirectional reflectance distribution function, in full V({lambda})-range (360 nm-830 nm) with arbitrarymore » angles of irradiation and detection relative to the surface normal, on a time scale of about 2 min. First goniometric measurements of diffuse reflection within 3D-space above the DUT with subsequent colorimetric representation of the obtained data of special effect pigments based on the interference effect are presented.« less

Software Aids In Graphical Depiction Of Flow Data

NASA Technical Reports Server (NTRS)

Stegeman, J. D.

1995-01-01

Interactive Data Display System (IDDS) computer program is graphical-display program designed to assist in visualization of three-dimensional flow in turbomachinery. Grid and simulation data files in PLOT3D format required for input. Able to unwrap volumetric data cone associated with centrifugal compressor and display results in easy-to-understand two- or three-dimensional plots. IDDS provides majority of visualization and analysis capability for Integrated Computational Fluid Dynamics and Experiment (ICE) system. IDDS invoked from any subsystem, or used as stand-alone package of display software. Generates contour, vector, shaded, x-y, and carpet plots. Written in C language. Input file format used by IDDS is that of PLOT3D (COSMIC item ARC-12782).

American College of Sports Medicine position stand. Quantity and quality of exercise for developing and maintaining cardiorespiratory, musculoskeletal, and neuromotor fitness in apparently healthy adults: guidance for prescribing exercise.

PubMed

Garber, Carol Ewing; Blissmer, Bryan; Deschenes, Michael R; Franklin, Barry A; Lamonte, Michael J; Lee, I-Min; Nieman, David C; Swain, David P

2011-07-01

The purpose of this Position Stand is to provide guidance to professionals who counsel and prescribe individualized exercise to apparently healthy adults of all ages. These recommendations also may apply to adults with certain chronic diseases or disabilities, when appropriately evaluated and advised by a health professional. This document supersedes the 1998 American College of Sports Medicine (ACSM) Position Stand, "The Recommended Quantity and Quality of Exercise for Developing and Maintaining Cardiorespiratory and Muscular Fitness, and Flexibility in Healthy Adults." The scientific evidence demonstrating the beneficial effects of exercise is indisputable, and the benefits of exercise far outweigh the risks in most adults. A program of regular exercise that includes cardiorespiratory, resistance, flexibility, and neuromotor exercise training beyond activities of daily living to improve and maintain physical fitness and health is essential for most adults. The ACSM recommends that most adults engage in moderate-intensity cardiorespiratory exercise training for ≥30 min·d on ≥5 d·wk for a total of ≥150 min·wk, vigorous-intensity cardiorespiratory exercise training for ≥20 min·d on ≥3 d·wk (≥75 min·wk), or a combination of moderate- and vigorous-intensity exercise to achieve a total energy expenditure of ≥500-1000 MET·min·wk. On 2-3 d·wk, adults should also perform resistance exercises for each of the major muscle groups, and neuromotor exercise involving balance, agility, and coordination. Crucial to maintaining joint range of movement, completing a series of flexibility exercises for each the major muscle-tendon groups (a total of 60 s per exercise) on ≥2 d·wk is recommended. The exercise program should be modified according to an individual's habitual physical activity, physical function, health status, exercise responses, and stated goals. Adults who are unable or unwilling to meet the exercise targets outlined here still can benefit from engaging in amounts of exercise less than recommended. In addition to exercising regularly, there are health benefits in concurrently reducing total time engaged in sedentary pursuits and also by interspersing frequent, short bouts of standing and physical activity between periods of sedentary activity, even in physically active adults. Behaviorally based exercise interventions, the use of behavior change strategies, supervision by an experienced fitness instructor, and exercise that is pleasant and enjoyable can improve adoption and adherence to prescribed exercise programs. Educating adults about and screening for signs and symptoms of CHD and gradual progression of exercise intensity and volume may reduce the risks of exercise. Consultations with a medical professional and diagnostic exercise testing for CHD are useful when clinically indicated but are not recommended for universal screening to enhance the safety of exercise.

Naval Research Reviews. Volume 39, Number 3,

DTIC Science & Technology

1987-01-01

remote sensing, ice and waves, acoustics, and MIZEX East Research Area. biology . Operations benefitted greatly from SAR imagery, downlinked daily. in near...the carried out coordinated programs in oceanography . edd\\ Norwsegian Satellite Telemelr\\ Station under D).A. Horn. studies. biology and meteorology...processes are the principal generators of " ambient noise in the Arctic MIZ. 20 . % Biology Acknowledgements In MIZEX 87, growth rates and the standing

Seven years later: effects of wildfire in a young stand of Virginia pine and hardwoods

Treesearch

Richard H. Fenton

1960-01-01

In November 1952 a hot surface fire burned through part of a 30-year-old Virginia pine-hardwood stand near Beltsville, Md. Observations were made for the next 2 years to evaluate the effects of this type of fire under these stand conditions. The main direct effects during the 2 years, as reported by Church in 1955, were: 45 percent mortality of trees 1 inch d.b.h. and...

Forest Stand Segmentation Using Airborne LIDAR Data and Very High Resolution Multispectral Imagery

NASA Astrophysics Data System (ADS)

Dechesne, Clément; Mallet, Clément; Le Bris, Arnaud; Gouet, Valérie; Hervieu, Alexandre

2016-06-01

Forest stands are the basic units for forest inventory and mapping. Stands are large forested areas (e.g., ≥ 2 ha) of homogeneous tree species composition. The accurate delineation of forest stands is usually performed by visual analysis of human operators on very high resolution (VHR) optical images. This work is highly time consuming and should be automated for scalability purposes. In this paper, a method based on the fusion of airborne laser scanning data (or lidar) and very high resolution multispectral imagery for automatic forest stand delineation and forest land-cover database update is proposed. The multispectral images give access to the tree species whereas 3D lidar point clouds provide geometric information on the trees. Therefore, multi-modal features are computed, both at pixel and object levels. The objects are individual trees extracted from lidar data. A supervised classification is performed at the object level on the computed features in order to coarsely discriminate the existing tree species in the area of interest. The analysis at tree level is particularly relevant since it significantly improves the tree species classification. A probability map is generated through the tree species classification and inserted with the pixel-based features map in an energetical framework. The proposed energy is then minimized using a standard graph-cut method (namely QPBO with α-expansion) in order to produce a segmentation map with a controlled level of details. Comparison with an existing forest land cover database shows that our method provides satisfactory results both in terms of stand labelling and delineation (matching ranges between 94% and 99%).

Heteromorphic NiCo2S4/Ni3S2/Ni Foam as a Self-Standing Electrode for Hydrogen Evolution Reaction in Alkaline Solution.

PubMed

Liu, Hui; Ma, Xiao; Rao, Yuan; Liu, Yang; Liu, Jialiang; Wang, Luyang; Wu, Mingbo

2018-04-04

Considerable works have been devoted on developing high-efficiency nonplatinum electrocatalysts for hydrogen evolution reaction (HER). Herein, 3D heteromorphic NiCo 2 S 4 /Ni 3 S 2 nanosheets network has been constructed on Ni foam (denoted as NiCo 2 S 4 /Ni 3 S 2 /NF) serving as a self-standing electrocatalyst through directly thermal sulfurization of a single-source NiCo-layered double hydroxide precursor. The resultant NiCo 2 S 4 /Ni 3 S 2 /NF electrode exhibits outstanding electrocatalytic HER performance with an extremely low onset overpotential of 15 mV and long-term durability in alkaline solution. Such enhanced HER performance can be credited to (1) the massive exposed active sites provided by mixed transition metal chalcogenides (NiCo 2 S 4 and Ni 3 S 2 ), (2) the strong interfacial interaction at NiCo 2 S 4 /Ni 3 S 2 heterojunction interfaces with the strengthened H binding, and (3) the porous highly conductive Ni foam substrate with accelerated electron transfer. This work opens up a new direction to fabricate effective and non-noble-metal electrodes for water splitting and hydrogen generation.

Rasterstereographic analysis of axial back surface rotation in standing versus forward bending posture in idiopathic scoliosis.

PubMed

Hackenberg, Lars; Hierholzer, Eberhard; Bullmann, Viola; Liljenqvist, Ulf; Götze, Christian

2006-07-01

The forward bending test according to Adams and rib hump quantification by scoliometer are common clinical examination techniques in idiopathic scoliosis, although precise data about the change of axial surface rotation in forward bending posture are not available. In a pilot study the influence of leg length inequalities on the back shape of five normal subjects was clarified. Then 91 patients with idiopathic scoliosis with Cobb-angles between 20 degrees and 82 degrees were examined by rasterstereography, a 3D back surface analysis system. The axial back surface rotation in standing posture was compared with that in forward bending posture and additionally with a scoliometer measurement in forward bending posture. The changes of back shape in forward bending posture were correlated with the Cobb-angle, the level of the apex of the scoliotic primary curve and the age of the patient. Averaged over all patients, the back surface rotation amplitude increased from 23.1 degrees in standing to 26.3 degrees in forward bending posture. The standard deviation of this difference was high (6.1 degrees ). The correlation of back surface rotation amplitude in standing with that in forward bending posture was poor (R (2)=0.41) as was the correlation of back surface rotation in standing posture with the scoliometer in forward bending posture measured rotation (R (2)=0.35). No significant correlation could be found between the change of back shape in forward bending and the degree of deformity (R (2)=0.07), likewise no correlation with the height of the apex of the scoliosis (R (2)=0.005) and the age of the patient (R (2)=0.001). Before forward bending test leg length inequalities have to be compensated accurately. Compared to the standing posture, forward bending changes back surface rotation. However, this change varies greatly between patients, and is independent of the type and degree of scoliosis. Furthermore remarkable differences were found between scoliometer measurement of the rib hump and rasterstereographic measurement of the vertebral rotation. Therefore the forward bending test and the identification of idiopathic scoliosis rotation by scoliometer can be markedly different compared to rasterstereographic surface measurement in the standing posture.

Multidimensional simulations of core-collapse supernovae with CHIMERA

NASA Astrophysics Data System (ADS)

Lentz, Eric J.; Bruenn, S. W.; Yakunin, K.; Endeve, E.; Blondin, J. M.; Harris, J. A.; Hix, W. R.; Marronetti, P.; Messer, O. B.; Mezzacappa, A.

2014-01-01

Core-collapse supernovae are driven by a multidimensional neutrino radiation hydrodynamic (RHD) engine, and full simulation requires at least axisymmetric (2D) and ultimately symmetry-free 3D RHD simulation. We present recent and ongoing work with our multidimensional RHD supernova code CHIMERA to understand the nature of the core-collapse explosion mechanism and its consequences. Recently completed simulations of 12-25 solar mass progenitors(Woosley & Heger 2007) in well resolved (0.7 degrees in latitude) 2D simulations exhibit robust explosions meeting the observationally expected explosion energy. We examine the role of hydrodynamic instabilities (standing accretion shock instability, neutrino driven convection, etc.) on the explosion dynamics and the development of the explosion energy. Ongoing 3D and 2D simulations examine the role that simulation resolution and the removal of the imposed axisymmetry have in the triggering and development of an explosion from stellar core collapse. Companion posters will explore the gravitational wave signals (Yakunin et al.) and nucleosynthesis (Harris et al.) of our simulations.

A-3 Test Stand work

NASA Image and Video Library

2011-07-29

Work continues on the A-3 Test Stand at Stennis Space Center. The new stand will allow operators to test next-generation rocket engines at simulated altitudes up to 100,000 feet. The test stand is scheduled for completion and activation in 2013.

Stem extension and mechanical stability of Xanthium canadense grown in an open or in a dense stand

PubMed Central

Watari, Ryoji; Nagashima, Hisae; Hirose, Tadaki

2014-01-01

Background and Aims Plants in open, uncrowded habitats typically have relatively short stems with many branches, whereas plants in crowded habitats grow taller and more slender at the expense of mechanical stability. There seems to be a trade-off between height growth and mechanical stability, and this study addresses how stand density influences stem extension and consequently plant safety margins against mechanical failure. Methods Xanthium canadense plants were grown either solitarily (S-plants) or in a dense stand (D-plants) until flowering. Internode dimensions and mechanical properties were measured at the metamer level, and the critical buckling height beyond which the plant elastically buckles under its own weight and the maximum lateral wind force the plant can withstand were calculated. Key Results Internodes were longer in D- than S-plants, but basal diameter did not differ significantly. Relative growth rates of internode length and diameter were negatively correlated to the volumetric solid fraction of the internode. Internode dry mass density was higher in S- than D-plants. Young's modulus of elasticity and the breaking stress were higher in lower metamers, and in D- than in S-plants. Within a stand, however, both moduli were positively related to dry mass density. The buckling safety factor, a ratio of critical buckling height to actual height, was higher in S- than in D-plants. D-plants were found to be approaching the limiting value 1. Lateral wind force resistance was higher in S- than in D-plants, and increased with growth in S-plants. Conclusions Critical buckling height increased with height growth due mainly to an increase in stem stiffness and diameter and a reduction in crown/stem mass ratio. Lateral wind force resistance was enhanced due to increased tissue strength and diameter. The increase in tissue stiffness and strength with height growth plays a crucial role in maintaining a safety margin against mechanical failure in herbaceous species that lack the capacity for secondary growth. PMID:24879768

Stretchable All-Gel-State Fiber-Shaped Supercapacitors Enabled by Macromolecularly Interconnected 3D Graphene/Nanostructured Conductive Polymer Hydrogels.

PubMed

Li, Panpan; Jin, Zhaoyu; Peng, Lele; Zhao, Fei; Xiao, Dan; Jin, Yong; Yu, Guihua

2018-05-01

Nanostructured conductive polymer hydrogels (CPHs) have been extensively applied in energy storage owing to their advantageous features, such as excellent electrochemical activity and relatively high electrical conductivity, yet the fabrication of self-standing and flexible electrode-based CPHs is still hampered by their limited mechanical properties. Herein, macromolecularly interconnected 3D graphene/nanostructured CPH is synthesized via self-assembly of CPHs and graphene oxide macrostructures. The 3D hybrid hydrogel shows uniform interconnectivity and enhanced mechanical properties due to the strong macromolecular interaction between the CPHs and graphene, thus greatly reducing aggregation in the fiber-shaping process. A proof-of-concept all-gel-state fibrous supercapacitor based on the 3D polyaniline/graphene hydrogel is fabricated to demonstrate the outstanding flexibility and mouldability, as well as superior electrochemical properties enabled by this 3D hybrid hydrogel design. The proposed device can achieve a large strain (up to ≈40%), and deliver a remarkable volumetric energy density of 8.80 mWh cm -3 (at power density of 30.77 mW cm -3 ), outperforming many fiber-shaped supercapacitors reported previously. The all-hydrogel design opens up opportunities in the fabrication of next-generation wearable and portable electronics. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Precise 3D printing of micro/nanostructures using highly conductive carbon nanotube-thiol-acrylate composites

NASA Astrophysics Data System (ADS)

Liu, Y.; Xiong, W.; Jiang, L. J.; Zhou, Y. S.; Lu, Y. F.

2016-04-01

Two-photon polymerization (TPP) is of increasing interest due to its unique combination of truly three-dimensional (3D) fabrication capability and ultrahigh spatial resolution of ~40 nm. However, the stringent requirements of non-linear resins seriously limit the material functionality of 3D printing via TPP. Precise fabrication of 3D micro/nanostructures with multi-functionalities such as high electrical conductivity and mechanical strength is still a long-standing challenge. In this work, TPP fabrication of arbitrary 3D micro/nanostructures using multi-walled carbon nanotube (MWNT)-thiolacrylate (MTA) composite resins has been developed. Up to 0.2 wt% MWNTs have been incorporated into thiol-acrylate resins to form highly stable and uniform composite photoresists without obvious degradation for one week at room temperature. Various functional 3D micro/nanostructures including woodpiles, micro-coils, spiral-like photonic crystals, suspended micro-bridges, micro-gears and complex micro-cars have been successfully fabricated. The MTA composite resin offers significant enhancements in electrical conductivity and mechanical strength, and on the same time, preserving high optical transmittance and flexibility. Tightly controlled alignment of MWNTs and the strong anisotropy effect were confirmed. Microelectronic devices including capacitors and resistors made of the MTA composite polymer were demonstrated. The 3D micro/nanofabrication using the MTA composite resins enables the precise 3D printing of micro/nanostructures of high electrical conductivity and mechanical strength, which is expected to lead a wide range of device applications, including micro/nano-electromechanical systems (MEMS/NEMS), integrated photonics and 3D electronics.

Iron encapsulated in 3D N-doped carbon nanotube/porous carbon hybrid from waste biomass for enhanced oxidative activity.

PubMed

Yao, Yunjin; Zhang, Jie; Wu, Guodong; Wang, Shaobin; Hu, Yi; Su, Cong; Xu, Tongwen

2017-03-01

Novel iron encapsulated in nitrogen-doped carbon nanotubes (CNTs) supported on porous carbon (Fe@N-C) 3D structured materials for degrading organic pollutants were fabricated from a renewable, low-cost biomass, melamine, and iron salt as the precursors. SEM and TEM micrographs show that iron encapsulated bamboo shaped CNTs are vertically standing on carbon sheets, and thus, a 3D hybrid was formed. The catalytic activities of the prepared samples were thoroughly evaluated by activation of peroxymonosulfate for catalytic oxidation of Orange II solutions. The influences of some reaction conditions (pH, temperature, and concentrations of reactants, peroxymonosulfate, and dye) were extensively evaluated. It was revealed that the adsorption could enrich the pollutant which was then rapidly degraded by the catalytically generated radicals, accelerating the continuous adsorption of residual pollutant. Remarkable carbon structure, introduction of CNTs, and N/Fe doping result in promoted adsorption capability and catalytic performances. Due to the simple synthetic process and cheap carbon precursor, Fe@N-C 3D hybrid can be easily scaled up and promote the development of Fenton-like catalysts.

Molecular Dynamics Visualization (MDV): Stereoscopic 3D Display of Biomolecular Structure and Interactions Using the Unity Game Engine.

PubMed

Wiebrands, Michael; Malajczuk, Chris J; Woods, Andrew J; Rohl, Andrew L; Mancera, Ricardo L

2018-06-21

Molecular graphics systems are visualization tools which, upon integration into a 3D immersive environment, provide a unique virtual reality experience for research and teaching of biomolecular structure, function and interactions. We have developed a molecular structure and dynamics application, the Molecular Dynamics Visualization tool, that uses the Unity game engine combined with large scale, multi-user, stereoscopic visualization systems to deliver an immersive display experience, particularly with a large cylindrical projection display. The application is structured to separate the biomolecular modeling and visualization systems. The biomolecular model loading and analysis system was developed as a stand-alone C# library and provides the foundation for the custom visualization system built in Unity. All visual models displayed within the tool are generated using Unity-based procedural mesh building routines. A 3D user interface was built to allow seamless dynamic interaction with the model while being viewed in 3D space. Biomolecular structure analysis and display capabilities are exemplified with a range of complex systems involving cell membranes, protein folding and lipid droplets.

Restoration management in redwood forests degraded by sudden oak death

Treesearch

Richard C. Cobb; Peter Hartsough; Kerri Frangioso; Janet Klein; Mike Swezy; Andrea Williams; Carl Sanders; Susan J. Frankel; David M. Rizzo

2017-01-01

We describe the foundation, objectives, and initial results from a stand-level experiment focused on restoration of redwood (Sequoia sempervirens (D. Don) Endl.) forests impacted by sudden oak death (SOD), caused by Phytophthora ramorum. Our study stands were primed for heavy impacts by SOD. Extensive harvesting which ended...

D.b.h./crown diameter relationships in mixed Appalachian hardwood stands

Treesearch

Neil I. Lamson; Neil I. Lamson

1987-01-01

Linear regression formulae for predicting crown diameter as a function of stem diameter are presented for nine species found in 50- to 80-year-old mixed hardwood stands in north-central West Virginia. Generally, crown diameter was closely related to tolerance; more tolerant species had larger crowns.

A-3 Test Stand work

NASA Image and Video Library

2011-07-29

Stennis Space Center employees have installed liquid oxygen and liquid hydrogen tanks atop the A-3 Test Stand, raising the structure to its full 300-foot height. The stand is being built to test next-generation rocket engines that could carry humans beyond low-Earth orbit into deep space. The A-3 Test Stand is scheduled for completion and activation in 2013.

Low-temperature atomic layer deposition of SiO2/Al2O3 multilayer structures constructed on self-standing films of cellulose nanofibrils.

PubMed

Putkonen, Matti; Sippola, Perttu; Svärd, Laura; Sajavaara, Timo; Vartiainen, Jari; Buchanan, Iain; Forsström, Ulla; Simell, Pekka; Tammelin, Tekla

2018-02-13

In this paper, we have optimized a low-temperature atomic layer deposition (ALD) of SiO 2 using AP-LTO® 330 and ozone (O 3 ) as precursors, and demonstrated its suitability to surface-modify temperature-sensitive bio-based films of cellulose nanofibrils (CNFs). The lowest temperature for the thermal ALD process was 80°C when the silicon precursor residence time was increased by the stop-flow mode. The SiO 2 film deposition rate was dependent on the temperature varying within 1.5-2.2 Å cycle -1 in the temperature range of 80-350°C, respectively. The low-temperature SiO 2 process that resulted was combined with the conventional trimethyl aluminium + H 2 O process in order to prepare thin multilayer nanolaminates on self-standing CNF films. One to six stacks of SiO 2 /Al 2 O 3 were deposited on the CNF films, with individual layer thicknesses of 3.7 nm and 2.6 nm, respectively, combined with a 5 nm protective SiO 2 layer as the top layer. The performance of the multilayer hybrid nanolaminate structures was evaluated with respect to the oxygen and water vapour transmission rates. Six stacks of SiO 2 /Al 2 O with a total thickness of approximately 35 nm efficiently prevented oxygen and water molecules from interacting with the CNF film. The oxygen transmission rates analysed at 80% RH decreased from the value for plain CNF film of 130 ml m -2  d -1 to 0.15 ml m -2  d -1 , whereas the water transmission rates lowered from 630 ± 50 g m -2  d -1 down to 90 ± 40 g m -2  d -1 This article is part of a discussion meeting issue 'New horizons for cellulose nanotechnology'. © 2017 The Author(s).

Low-temperature atomic layer deposition of SiO2/Al2O3 multilayer structures constructed on self-standing films of cellulose nanofibrils

NASA Astrophysics Data System (ADS)

Putkonen, Matti; Sippola, Perttu; Svärd, Laura; Sajavaara, Timo; Vartiainen, Jari; Buchanan, Iain; Forsström, Ulla; Simell, Pekka; Tammelin, Tekla

2017-12-01

In this paper, we have optimized a low-temperature atomic layer deposition (ALD) of SiO2 using AP-LTO® 330 and ozone (O3) as precursors, and demonstrated its suitability to surface-modify temperature-sensitive bio-based films of cellulose nanofibrils (CNFs). The lowest temperature for the thermal ALD process was 80°C when the silicon precursor residence time was increased by the stop-flow mode. The SiO2 film deposition rate was dependent on the temperature varying within 1.5-2.2 Å cycle-1 in the temperature range of 80-350°C, respectively. The low-temperature SiO2 process that resulted was combined with the conventional trimethyl aluminium + H2O process in order to prepare thin multilayer nanolaminates on self-standing CNF films. One to six stacks of SiO2/Al2O3 were deposited on the CNF films, with individual layer thicknesses of 3.7 nm and 2.6 nm, respectively, combined with a 5 nm protective SiO2 layer as the top layer. The performance of the multilayer hybrid nanolaminate structures was evaluated with respect to the oxygen and water vapour transmission rates. Six stacks of SiO2/Al2O with a total thickness of approximately 35 nm efficiently prevented oxygen and water molecules from interacting with the CNF film. The oxygen transmission rates analysed at 80% RH decreased from the value for plain CNF film of 130 ml m-2 d-1 to 0.15 ml m-2 d-1, whereas the water transmission rates lowered from 630 ± 50 g m-2 d-1 down to 90 ± 40 g m-2 d-1. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

Effects of space allowance on the behavior and physiology of cattle temporarily managed on rubber mats.

PubMed

Schütz, Karin E; Huddart, Frances J; Sutherland, Mhairi A; Stewart, Mairi; Cox, Neil R

2015-09-01

Dairy cattle managed in some pasture-based systems, such as in New Zealand, are predominantly kept outdoors all year around but are taken off pasture for periods, especially in wet weather to avoid soil damage. The use of rubber matting for such stand-off practices is becoming more common to improve animal welfare, and our objective was to investigate the effects of different space allowances on cow behavior and physiology when managed temporarily on rubber mats during a weather-induced stand-off period. Thirty pregnant, nonlactating Holstein-Friesian dairy cows were divided into 6 groups of 5 and exposed to 6 treatments following a Williams designed 6×6 Latin square. The treatments consisted of 6 space allowances on a 24-mm rubber surface during a simulated weather-induced stand-off period: 3.0, 4.5, 6.0, 7.5, 9.0, and 10.5 m(2)/cow. The stand-off period consisted of 18 h in the treatment pens followed by 6 h at pasture to allow for their daily feed intake (no feed was available during stand-off, following normal farm practice), for 3 consecutive days, with 6 d of recovery on pasture between treatments. When cows had more space available during the stand-off period, they spent more time lying on the rubber mats and less time lying on pasture during their daily 6-h feed break. Mean lying times (24 h, pasture and rubber mats combined) for the different space allowances were for 3.0 m(2)=7.5 h, 4.5 m(2)=10.2 h, 6.0 m(2)=11.9 h, 7.5 m(2)=12.4 h, and 10.5 m(2)=13.8 h. At 6.0 m(2) of space allowance per cow, the animals spent similar times lying per 24 h as when the cows were on recovery on pasture in between treatments (11.9 and 11.2 h, respectively). Aggressive interactions and nonaggressive lying disturbances were more frequent at lower space allowances (aggressive interactions decreased by 35% from 3.0 to 4.5 m(2)/cow, with a slower decline thereafter). Cows were dirtier after the stand-off period, particularly at lower space allowances. All cows had higher gait scores after the stand-off period; however, this change was unaffected by space allowance and very minor. Stride length, plasma cortisol, and body weight were all unaffected by the stand-off period and space allowance. The results suggest that to reduce aggressive behavior and maintain adequate lying times, dairy cattle managed temporarily on rubber matting for up to 18 h per day, without feed, should have a space allowance of at least 4.5 to 6.0 m(2) per cow. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Standing waves, clustering, and phase waves in 1D simulations of kinetic relaxation oscillations in NO+NH 3 on Pt(1 0 0) coupled by diffusion

NASA Astrophysics Data System (ADS)

Uecker, Hannes

2004-04-01

The Lombardo-Imbihl-Fink (LFI) ODE model of the NO+NH 3 reaction on a Pt(1 0 0) surface shows stable relaxation oscillations with very sharp transitions for temperatures T between 404 and 433 K. Here we study numerically the effect of linear diffusive coupling of these oscillators in one spatial dimension. Depending on the parameters and initial conditions we find a rich variety of spatio-temporal patterns which we group into four main regimes: bulk oscillations (BOs), standing waves (SW), phase clusters (PC), and phase waves (PW). Two key ingredients for SW and PC are identified, namely the relaxation type of the ODE oscillations and a nonlocal (and nonglobal) coupling due to relatively fast diffusion of the kinetically slaved variables NH 3 and H. In particular, the latter replaces the global coupling through the gas phase used to obtain SW and PC in models of related surface reactions. The PW exist only under the assumption of (relatively) slow diffusion of NH 3 and H.

Saturable absorption in one-dimensional Sb₂Se₃ nanowires in the visible to near-infrared region.

PubMed

Yadav, Rajesh Kumar; Sharma, Rituraj; Aneesh, J; Abhiramnath, P; Adarsh, K V

2016-05-01

One-dimensional (1D) free-standing nanowires are particularly important for carrier confinement in two dimensions, which provides a platform to explore the nonlinear optical phenomena at the nanoscale. In this Letter, we demonstrate saturable absorption in the resonant and above-bandgap excitations of both ns and fs pulses in 1D crystalline Sb₂Se₃ nanowires prepared by the facile hydrothermal method. Impressively, the average length of the nanowires extends to a few micrometers with a high aspect ratio of 300. The excited-state to ground-state absorption cross-section ratio in Sb₂Se₃ nanowires is ≈0.23, which suggests that they can be utilized as passive mode lockers.

Research and Development Program to Develop a Nondestructive Evaluation Instrument (X-Ray Diffraction) for Measuring Residual Stresses in a Wide Range of Naval Aviation Material. Phase 2

DTIC Science & Technology

1987-04-03

Using Cr KO Radiation 3-20 Smaary of Residual Stress for Navy Pensacola Nickel-Plated 3-64 Camshaft 75 £51 3-21 Surface Residual Stresses in Nickel-Plated...NAN - Pensacola. The data obtained from the H-3 camshafts produced perplexing results due to sLn 2 * splitting and non-linear d-spacing versus sin2...com- pressive stress values on one of the nickel-plated camshafts . An additional objective of the Phase II nickel-plating study was to under- stand the

Candida meningitis in an immunocompetent patient detected through (1→3)-beta-d-glucan.

PubMed

Farrugia, Mark K; Fogha, Evan P; Miah, Abdul R; Yednock, Joel; Palmer, H Carl; Guilfoose, John

2016-10-01

A 44-year-old female presented with a 3-month history of headache, dizziness, nausea, and vomiting. Her past medical history was significant for long-standing intravenous drug abuse. Shortly after admission, the patient became hypertensive and febrile, with fever as high as 38.8°C. The lumbar puncture profile supported an infectious process; however multiple cultures of blood and cerebrospinal fluid (CSF) did not initially show growth of organisms. Finally after 9 days of incubation, a CSF culture showed evidence of a few colonies of Candida albicans. To confirm the diagnosis, preserved CSF from that sample was tested for (1→3)-β-d-glucan, showing levels >500pg/ml. This report illustrates a rare complication of intravenous drug use in an immunocompetent patient and demonstrates the utility of (1→3)-β-d-glucan testing in possible Candida meningitis. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

The Association of Glaucomatous Visual Field Loss and Balance

PubMed Central

de Luna, Regina A.; Mihailovic, Aleksandra; Nguyen, Angeline M.; Friedman, David S.; Gitlin, Laura N.; Ramulu, Pradeep Y.

2017-01-01

Purpose To relate balance measures to visual field (VF) damage from glaucoma. Methods The OPAL kinematic system measured balance, as root mean square (RMS) sway, on 236 patients with suspect/diagnosed glaucoma. Balance was measured with feet shoulder width apart while standing on a firm/foam surface with eyes opened/closed (Instrumental Clinical Test of Sensory Integration and Balance [ICTSIB] conditions), and eyes open on a firm surface under feet together, semi-tandem, or tandem positions (standing balance conditions). Integrated VF (IVF) sensitivities were calculated by merging right and left eye 24-2 VF data. Results Mean age was 71 years (range, 57–93) and mean IVF sensitivity was 27.1 dB (normal = 31 dB). Lower IVF sensitivity was associated with greater RMS sway during eyes-open foam-surface testing (β = 0.23 z-score units/5 dB IVF sensitivity decrement, P = 0.001), but not during other ICTSIB conditions. Lower IVF sensitivity also was associated with greater RMS sway during feet together standing balance testing (0.10 z-score units/5 dB IVF sensitivity decrement, P = 0.049), but not during other standing balance conditions. Visual dependence of balance was lower in patients with worse IVF sensitivity (β = −21%/5 dB IVF sensitivity decrement, P < 0.001). Neither superior nor inferior IVF sensitivity consistently predicted balance measures better than measures of overall VF sensitivity. Conclusions Balance was worse in glaucoma patients with greater VF damage under foam surface testing (designed to inhibit proprioceptive contributions to balance) as well as feet-together firm-surface conditions when somatosensory inputs were available. Translational Relevance Good balance is essential to avoid unnecessary falls and patients with VF loss from glaucoma may be at higher risk of falls because of poor balance. PMID:28553562

3D-printed flow system for determination of lead in natural waters.

PubMed

Mattio, Elodie; Robert-Peillard, Fabien; Branger, Catherine; Puzio, Kinga; Margaillan, André; Brach-Papa, Christophe; Knoery, Joël; Boudenne, Jean-Luc; Coulomb, Bruno

2017-06-01

The development of 3D printing in recent years opens up a vast array of possibilities in the field of flow analysis. In the present study, a new 3D-printed flow system has been developed for the selective spectrophotometric determination of lead in natural waters. This system was composed of three 3D-printed units (sample treatment, mixing coil and detection) that might have been assembled without any tubing to form a complete flow system. Lead was determined in a two-step procedure. A preconcentration of lead was first carried out on TrisKem Pb Resin located in a 3D-printed column reservoir closed by a tapped screw. This resin showed a high extraction selectivity for lead over many tested potential interfering metals. In a second step, lead was eluted by ammonium oxalate in presence of 4-(2-pyridylazo)-resorcinol (PAR), and spectrophotometrically detected at 520nm. The optimized flow system has exhibited a linear response from 3 to 120µgL -1 . Detection limit, coefficient of variation and sampling rate were evaluated at 2.7µgL -1 , 5.4% (n=6) and 4 sampleh -1 , respectively. This flow system stands out by its fully 3D design, portability and simplicity for low cost analysis of lead in natural waters. Copyright © 2017 Elsevier B.V. All rights reserved.

Delineating the role of ripples on the thermal expansion of 2D honeycomb materials: graphene, 2D h-BN and monolayer (ML)-MoS2.

PubMed

Anees, P; Valsakumar, M C; Panigrahi, B K

2017-04-19

We delineated the role of thermally excited ripples on the thermal expansion properties of 2D honeycomb materials (free-standing graphene, 2D h-BN, and ML-MoS 2 ), by explicitly carrying out three-dimensional (3D) and two-dimensional (2D) molecular dynamics simulations. In 3D simulations, the in-plane lattice parameter (a-lattice) of graphene and 2D h-BN shows thermal contraction over a wide range of temperatures and exhibits a strong system size dependence. The 2D simulations of the very same system show a reverse trend, where the a-lattice expands in the whole computed temperature range. In contrast to graphene and 2D h-BN, the a-lattice of ML-MoS 2 shows thermal expansion in both 2D and 3D simulations and their system size dependence is marginal. By analyzing the phonon dispersion at 300 K, we found that the discrepancy between 2D and 3D simulations of graphene and 2D h-BN is due to the absence of out-of-plane bending modes (ZA) in 2D simulations, which is responsible for the thermal contraction of the a-lattice at low temperature. Meanwhile, all the phonon modes are present in the 2D phonon dispersion of ML-MoS 2 , which indicates that the origin of the ZA mode is not purely due to the out-of-plane movement of atoms and also its effect on thermal expansion is not significant as found in graphene and 2D h-BN.

NASA Day at the Capitol

NASA Image and Video Library

2009-02-19

Stennis Space Center leaders and guests visit with Mississippi Senate members in chambers during NASA Day at the Capitol events in Jackson on Feb. 19. Standing at the Senate podium (rear) is Mississippi Lt. Gov. Phil Bryant. Standing at the lectern below are (l to r): Sen. David Baria, D-Bay St. Louis; Partners for Stennis Chair Clay Wagner; NASA Shared Services Center Director Rick Arbuthnot; astronaut Rex Walheim; Stennis Space Center Director Gene Goldman; President Pro Tempore Billy Hewes, R-Gulfport; Sen. Ezell Lee, D-Picayune; and Sen. Tommy Gollott, R-Biloxi.

Computer simulation of the effect of dDAVP with saline loading on fluid balance after 24-hour head-down tilt

NASA Technical Reports Server (NTRS)

Srinivasan, R. S.; Simanonok, K. E.; Charles, J. B.

1994-01-01

Fluid loading (FL) before Shuttle reentry is a countermeasure currently in use by NASA to improve the orthostatic tolerance of astronauts during reentry and postflight. The fluid load consists of water and salt tablets equivalent to 32 oz (946 ml) of isotonic saline. However, the effectiveness of this countermeasure has been observed to decrease with the duration of spaceflight. The countermeasure's effectiveness may be improved by enhancing fluid retention using analogs of vasopressin such as lypressin (LVP) and desmopressin (dDAVP). In a computer simulation study reported previously, we attempted to assess the improvement in fluid retention obtained by the use of LVP administered before FL. The present study is concerned with the use of dDAVP. In a recent 24-hour, 6 degree head-down tilt (HDT) study involving seven men, dDAVP was found to improve orthostatic tolerance as assessed by both lower body negative pressure (LBNP) and stand tests. The treatment restored Luft's cumulative stress index (cumulative product of magnitude and duration of LBNP) to nearly pre-bedrest level. The heart rate was lower and stroke volume was marginally higher at the same LBNP levels with administration of dDAVP compared to placebo. Lower heart rates were also observed with dDAVP during stand test, despite the lower level of cardiovascular stress. These improvements were seen with only a small but significant increase in plasma volume of approximately 3 percent. This paper presents a computer simulation analysis of some of the results of this HDT study.

Accessing 3D Location of Standing Pelvis: Relative Position of Sacral Plateau and Acetabular Cavities versus Pelvis

PubMed Central

Berthonnaud, E.; Hilmi, R.; Dimnet, J.

2012-01-01

The goal of this paper is to access to pelvis position and morphology in standing posture and to determine the relative locations of their articular surfaces. This is obtained from coupling biplanar radiography and bone modeling. The technique involves different successive steps. Punctual landmarks are first reconstructed, in space, from their projected images, identified on two orthogonal standing X-rays. Geometric models, of global pelvis and articular surfaces, are determined from punctual landmarks. The global pelvis is represented as a triangle of summits: the two femoral head centers and the sacral plateau center. The two acetabular cavities are modeled as hemispheres. The anterior sacral plateau edge is represented by an hemi-ellipsis. The modeled articular surfaces are projected on each X-ray. Their optimal location is obtained when the projected contours of their models best fit real outlines identified from landmark images. Linear and angular parameters characterizing the position of global pelvis and articular surfaces are calculated from the corresponding sets of axis. Relative positions of sacral plateau, and acetabular cavities, are then calculated. Two hundred standing pelvis, of subjects and scoliotic patients, have been studied. Examples are presented. They focus upon pelvis orientations, relative positions of articular surfaces, and pelvis asymmetries. PMID:22567279

[Herbal textual research on relationship between Chinese medicine"Shihu" (Dendrobium spp.) and "Tiepi Shihu" (D. catenatum)].

PubMed

Si, Jin-Ping; Zhang, Yuan; Luo, Yi-Bo; Liu, Jing-Jing; Liu, Zhong-Jian

2017-05-01

Dendrobium species on the ancient Chinese herbal texts were investigated in this paper, including their dscriptions of original species, producing areas and quality. Our results indicated that the major producing areas were Lu'an, Anhui province and Wenzhou, Taizhou, Zhejiang province. In addition, the sweet flavor, short, thin and solid stems were standing for good quality. Based on the stable producing areas and quality descriptions, D. catenatum (D. officinale) ("Tiepi Shihu") and D. houshanense were high quality medicinal Dendrobium species ("Shihu" ) in ancient China. Besides, there were 3 scientific names for "Tiepi Shihu", including D. candidum, D. officinale, D. catenatum. After textual investigation, We suggest that D. catenatum should be its scientific name, and D. officinale was synonyms published later. However, the name "D. officinale" could be reserved as it is much more popular used in publication and commodities. Moreover, its Chinese name should be "Tiepi Shihu". Copyright© by the Chinese Pharmaceutical Association.

Synthesis and characterization of 2D molybdenum carbide (MXene)

DOE PAGES

Halim, Joseph; Kota, Sankalp; Lukatskaya, Maria R.; ...

2016-02-17

Large scale synthesis and delamination of 2D Mo 2CT x (where T is a surface termination group) has been achieved by selectively etching gallium from the recently discovered nanolaminated, ternary transition metal carbide Mo 2Ga 2C. Different synthesis and delamination routes result in different flake morphologies. The resistivity of free-standing Mo 2CT x films increases by an order of magnitude as the temperature is reduced from 300 to 10 K, suggesting semiconductor-like behavior of this MXene, in contrast to Ti 3C 2T x which exhibits metallic behavior. At 10 K, the magnetoresistance is positive. Additionally, changes in electronic transport aremore » observed upon annealing of the films. When 2 μm thick films are tested as electrodes in supercapacitors, capacitances as high as 700 F cm –3 in a 1 m sulfuric acid electrolyte and high capacity retention for at least 10,000 cycles at 10 A g –1 are obtained. Free-standing Mo 2CT x films, with ≈8 wt% carbon nanotubes, perform well when tested as an electrode material for Li-ions, especially at high rates. In conclusion, at 20 and 131 C cycling rates, stable reversible capacities of 250 and 76 mAh g –1, respectively, are achieved for over 1000 cycles.« less

Electrospun LiFePO₄/C Composite Fiber Membrane as a Binder-Free, Self-Standing Cathode for Power Lithium-Ion Battery.

PubMed

Chen, Li-Li; Shen, Xiang-Qian; Jing, Mao-Xiang; Zhu, Sheng-Wen; Pi, Zhi-Chao; Li, Jing-Quan; Zhai, Hong-Ai; Xiao, Ke-Song

2018-07-01

A LiFePO4/C composite fiber membrane was fabricated by the electrospinning method and subsequent thermal treatment. The thermal decomposition process was analyzed by TG/DSC, the morphology, microstructure and composition were studied using SEM, TEM, XRD, Raman, respectively. The results indicated that the prepared LiFePO4/C composite fibers were composed of nanosized LiFePO4 crystals and amorphous carbon coatings, which formed a three dimensional (3D) long-range networks, greatly enhanced the electronic conductivity of LiFePO4 electrode up to 3.59× 10-2 S · cm-2. The 3D LiFePO4/C fiber membrane could be directly used as a binder-free, self-standing cathode for lithium-ion battery, and exhibited an improved capacity and rate performance. The LiFePO4/C composite electrode delivered a discharge capacity of 116 mAh·g-1, 109 mAh·g-1, 103 mAh·g-1, 91 mAh·g-1, 80 mAh·g-1 at 0.1 C, 0.5 C, 1 C, 3 C, 5 C, respectively. And a stable cycling performance was also achieved that the specific capacity could retain 75 mA·g-1 after 500 cycles at 5 C. Therefore, this LiFePO4/C composite fiber membrane was promising to be used as a cathode for power lithium ion battery.

Semantic segmentation of forest stands of pure species combining airborne lidar data and very high resolution multispectral imagery

NASA Astrophysics Data System (ADS)

Dechesne, Clément; Mallet, Clément; Le Bris, Arnaud; Gouet-Brunet, Valérie

2017-04-01

Forest stands are the basic units for forest inventory and mapping. Stands are defined as large forested areas (e.g., ⩾ 2 ha) of homogeneous tree species composition and age. Their accurate delineation is usually performed by human operators through visual analysis of very high resolution (VHR) infra-red images. This task is tedious, highly time consuming, and should be automated for scalability and efficient updating purposes. In this paper, a method based on the fusion of airborne lidar data and VHR multispectral images is proposed for the automatic delineation of forest stands containing one dominant species (purity superior to 75%). This is the key preliminary task for forest land-cover database update. The multispectral images give information about the tree species whereas 3D lidar point clouds provide geometric information on the trees and allow their individual extraction. Multi-modal features are computed, both at pixel and object levels: the objects are individual trees extracted from lidar data. A supervised classification is then performed at the object level in order to coarsely discriminate the existing tree species in each area of interest. The classification results are further processed to obtain homogeneous areas with smooth borders by employing an energy minimum framework, where additional constraints are joined to form the energy function. The experimental results show that the proposed method provides very satisfactory results both in terms of stand labeling and delineation (overall accuracy ranges between 84 % and 99 %).

Development of a Thrust Stand to Meet LISA Mission Requirements

NASA Technical Reports Server (NTRS)

Willis, William D., III; Zakrzwski, Charles M.; Merkowitz, Stephen M.

2002-01-01

A thrust stand has been built to measure the force-noise produced by electrostatic micro-Newton (muN) thrusters. The LISA mission's Disturbance Reduction System (DRS) requires thrusters that are capable of producing continuous thrust levels between 1-100 muN with a resolution of 0.1 muN. The stationary force-noise produced by these thrusters must not exceed 0.1 muN/dHz in the measurement bandwidth 10(exp -4) to 1 Hz. The LISA Thrust Stand (LTS) is a torsion-balance type thrust stand designed to meet the following requirements: stationary force-noise measurements from l0( -4) to 1 Hz with 0.1 muN/dHz sensitivity, absolute thrust measurements from 1-100 muN with better than 0.1 muN resolution, and dynamic thruster response from to 10 Hz. The LTS employs a unique vertical configuration, autocollimator for angular position measurements, and electrostatic actuators that are used for dynamic pendulum control and null-mode measurements. Force-noise levels are measured indirectly by characterizing the thrust stand as a spring-mass system. The LTS was initially designed to test the indium FEEP thruster developed by the Austrian Research Center in Seibersdorf (ARCS), but can be modified for testing other thrusters of this type.

Dose-dependent pheromone responses of mountain pine beetle in stands of lodgepole pine

Treesearch

Daniel R. Miller; B. Staffan Lindgren; John H. Borden

2005-01-01

We conducted seven behavioral choice tests with Lindgren multiple-funnel traps in stands of mature lodgepole pine in British Columbia, from 1988 to 1994, to determine the dosedependent responses of the mountain pine beetle, Dendroctonus ponderosae Hopkins, to its pheromones. Amultifunctional dose-dependent response was exhibited by D. ...

Parallelization of elliptic solver for solving 1D Boussinesq model

NASA Astrophysics Data System (ADS)

Tarwidi, D.; Adytia, D.

2018-03-01

In this paper, a parallel implementation of an elliptic solver in solving 1D Boussinesq model is presented. Numerical solution of Boussinesq model is obtained by implementing a staggered grid scheme to continuity, momentum, and elliptic equation of Boussinesq model. Tridiagonal system emerging from numerical scheme of elliptic equation is solved by cyclic reduction algorithm. The parallel implementation of cyclic reduction is executed on multicore processors with shared memory architectures using OpenMP. To measure the performance of parallel program, large number of grids is varied from 28 to 214. Two test cases of numerical experiment, i.e. propagation of solitary and standing wave, are proposed to evaluate the parallel program. The numerical results are verified with analytical solution of solitary and standing wave. The best speedup of solitary and standing wave test cases is about 2.07 with 214 of grids and 1.86 with 213 of grids, respectively, which are executed by using 8 threads. Moreover, the best efficiency of parallel program is 76.2% and 73.5% for solitary and standing wave test cases, respectively.

Restoration of self-awareness of hypoglycemia in adults with long-standing type 1 diabetes: hyperinsulinemic-hypoglycemic clamp substudy results from the HypoCOMPaSS trial.

PubMed

Leelarathna, Lalantha; Little, Stuart A; Walkinshaw, Emma; Tan, Horng Kai; Lubina-Solomon, Alexandra; Kumareswaran, Kavita; Lane, Annette P; Chadwick, Thomas; Marshall, Sally M; Speight, Jane; Flanagan, Daniel; Heller, Simon R; Shaw, James A M; Evans, Mark L

2013-12-01

Impaired awareness of hypoglycemia (IAH) and defective counterregulation significantly increase severe hypoglycemia risk in type 1 diabetes (T1D). We evaluated restoration of IAH/defective counterregulation by a treatment strategy targeted at hypoglycemia avoidance in adults with T1D with IAH (Gold score ≥4) participating in the U.K.-based multicenter HypoCOMPaSS randomized controlled trial. Eighteen subjects with T1D and IAH (mean ± SD age 50 ± 9 years, T1D duration 35 ± 10 years, HbA1c 8.1 ± 1.0% [65 ± 10.9 mmol/mol]) underwent stepped hyperinsulinemic-hypoglycemic clamp studies before and after a 6-month intervention. The intervention comprised the HypoCOMPaSS education tool in all and randomized allocation, in a 2 × 2 factorial study design, to multiple daily insulin analog injections or continuous subcutaneous insulin infusion therapy and conventional glucose monitoring or real-time continuous glucose monitoring. Symptoms, cognitive function, and counterregulatory hormones were measured at each glucose plateau (5.0, 3.8, 3.4, 2.8, and 2.4 mmol/L), with each step lasting 40 min with subjects kept blinded to their actual glucose value throughout clamp studies. After intervention, glucose concentrations at which subjects first felt hypoglycemic increased (mean ± SE from 2.6 ± 0.1 to 3.1 ± 0.2 mmol/L, P = 0.02), and symptom and plasma metanephrine responses to hypoglycemia were higher (median area under curve for symptoms, 580 [interquartile range {IQR} 420-780] vs. 710 [460-1,260], P = 0.02; metanephrine, 2,412 [-3,026 to 7,279] vs. 5,180 [-771 to 11,513], P = 0.01). Glycemic threshold for deterioration of cognitive function measured by four-choice reaction time was unchanged, while the color-word Stroop test showed a degree of adaptation. Even in long-standing T1D, IAH and defective counterregulation may be improved by a clinical strategy aimed at hypoglycemia avoidance.

Diagnosing Postural Tachycardia Syndrome: Comparison of Tilt Test versus Standing Hemodynamics

PubMed Central

Plash, Walker B; Diedrich, André; Biaggioni, Italo; Garland, Emily M; Paranjape, Sachin Y; Black, Bonnie K; Dupont, William D; Raj, Satish R

2012-01-01

Postural tachycardia syndrome (POTS) is characterized by increased heart rate (ΔHR) of ≥30 bpm with symptoms related to upright posture. Active stand (STAND) and passive head-up tilt (TILT) produce different physiological responses. We hypothesized these different responses would affect the ability of individuals to achieve the POTS HR increase criterion. Patients with POTS (n=15) and healthy controls (n=15) underwent 30 min of TILT and STAND testing. ΔHR values were analyzed at 5 min intervals. Receiver Operating Characteristics analysis was performed to determine optimal cut point values of ΔHR for both TILT and STAND. TILT produced larger ΔHR than STAND for all 5 min intervals from 5 min (38±3 bpm vs. 33±3 bpm; P=0.03) to 30 min (51±3 bpm vs. 38±3 bpm; P<0.001). Sensitivity (Sn) of the 30 bpm criterion was similar for all tests (TILT-10=93%, STAND-10=87%, TILT30=100%, and STAND30=93%). Specificity (Sp) of the 30 bpm criterion was less at both 10 and 30 min for TILT (TILT10=40%, TILT30=20%) than STAND (STAND10=67%, STAND30=53%). The optimal ΔHR to discriminate POTS at 10 min were 38 bpm (TILT) and 29 bpm (STAND), and at 30 min were 47 bpm (TILT) and 34 bpm (STAND). Orthostatic tachycardia was greater for TILT (with lower specificity for POTS diagnosis) than STAND at 10 and 30 min. The 30 bpm ΔHR criterion is not suitable for 30 min TILT. Diagnosis of POTS should consider orthostatic intolerance criteria and not be based solely on orthostatic tachycardia regardless of test used. PMID:22931296

Diagnosing postural tachycardia syndrome: comparison of tilt testing compared with standing haemodynamics.

PubMed

Plash, Walker B; Diedrich, André; Biaggioni, Italo; Garland, Emily M; Paranjape, Sachin Y; Black, Bonnie K; Dupont, William D; Raj, Satish R

2013-01-01

POTS (postural tachycardia syndrome) is characterized by an increased heart rate (ΔHR) of ≥30 bpm (beats/min) with symptoms related to upright posture. Active stand (STAND) and passive head-up tilt (TILT) produce different physiological responses. We hypothesized these different responses would affect the ability of individuals to achieve the POTS HR increase criterion. Patients with POTS (n=15) and healthy controls (n=15) underwent 30 min of tilt and stand testing. ΔHR values were analysed at 5 min intervals. ROC (receiver operating characteristic) analysis was performed to determine optimal cut point values of ΔHR for both tilt and stand. Tilt produced larger ΔHR than stand for all 5 min intervals from 5 min (38±3 bpm compared with 33±3 bpm; P=0.03) to 30 min (51±3 bpm compared with 38±3 bpm; P<0.001). Sn (sensitivity) of the 30 bpm criterion was similar for all tests (TILT10=93%, STAND10=87%, TILT30=100%, and STAND30=93%). Sp (specificity) of the 30 bpm criterion was less at both 10 and 30 min for tilt (TILT10=40%, TILT30=20%) than stand (STAND10=67%, STAND30=53%). The optimal ΔHR to discriminate POTS at 10 min were 38 bpm (TILT) and 29 bpm (STAND), and at 30 min were 47 bpm (TILT) and 34 bpm (STAND). Orthostatic tachycardia was greater for tilt (with lower Sp for POTS diagnosis) than stand at 10 and 30 min. The 30 bpm ΔHR criterion is not suitable for 30 min tilt. Diagnosis of POTS should consider orthostatic intolerance criteria and not be based solely on orthostatic tachycardia regardless of test used.

Vehicle dynamics control by using a three-dimensional stabilizer pendulum system

NASA Astrophysics Data System (ADS)

Goodarzi, A.; Naghibian, M.; Choodan, D.; Khajepour, A.

2016-12-01

Active safety systems of a vehicle normally work well on tyre-road interactions, however, these systems deteriorate in performance on low-friction road conditions. To combat this effect, an innovative idea for the yaw moment and roll dynamic control is presented in this paper. This idea was inspired by the chase and run dynamics animals like cheetahs in the nature; cheetahs have the ability to swerve while running at very high speeds. A cheetah controls its dynamics by rotating its long tail. A three-dimensional stabilizer pendulum system (3D-SPS) resembles the rotational motion of the tail of a cheetah to improve the stability and safety of a vehicle. The idea has been developed in a stand-alone 3D stabilizer pendulum system as well as in an integrated control system, which consists of an ordinary differential braking direct yaw control (DYC) and active steering control that is assisted by the 3D-SPS. The performance of the proposed 3D-SPS has been evaluated over a wide range of handling manoeuvres by using a comprehensive numerical simulation. The results show the advantage of 3D-SPS over conventional control approaches, which are ineffective on low-friction road conditions and high lateral acceleration manoeuvres. It should however be noted that the best vehicle dynamics performance is obtained when an integrated 3D-SPS and DYC and AFS is utilised.

3D printed auto-mixing chip enables rapid smartphone diagnosis of anemia

PubMed Central

Plevniak, Kimberly; Campbell, Matthew; Hodges, Abby; He, Mei

2016-01-01

Clinical diagnosis requiring central facilities and site visits can be burdensome for patients in resource-limited or rural areas. Therefore, development of a low-cost test that utilizes smartphone data collection and transmission would beneficially enable disease self-management and point-of-care (POC) diagnosis. In this paper, we introduce a low-cost iPOC3D diagnostic strategy which integrates 3D design and printing of microfluidic POC device with smartphone-based disease diagnosis in one process as a stand-alone system, offering strong adaptability for establishing diagnostic capacity in resource-limited areas and low-income countries. We employ smartphone output (AutoCAD 360 app) and readout (color-scale analytical app written in-house) functionalities for rapid 3D printing of microfluidic auto-mixers and colorimetric detection of blood hemoglobin levels. The auto-mixing of reagents with blood via capillary force has been demonstrated in 1 second without the requirement of external pumps. We employed this iPOC3D system for point-of-care diagnosis of anemia using a training set of patients (nanemia = 16 and nhealthy = 6), which showed consistent measurements of blood hemoglobin levels (a.u.c. = 0.97) and comparable diagnostic sensitivity and specificity, compared with standard clinical hematology analyzer. Capable of 3D fabrication flexibility and smartphone compatibility, this work presents a novel diagnostic strategy for advancing personalized medicine and mobile healthcare. PMID:27733894

A computer-aided detection (CAD) system with a 3D algorithm for small acute intracranial hemorrhage

NASA Astrophysics Data System (ADS)

Wang, Ximing; Fernandez, James; Deshpande, Ruchi; Lee, Joon K.; Chan, Tao; Liu, Brent

2012-02-01

Acute Intracranial hemorrhage (AIH) requires urgent diagnosis in the emergency setting to mitigate eventual sequelae. However, experienced radiologists may not always be available to make a timely diagnosis. This is especially true for small AIH, defined as lesion smaller than 10 mm in size. A computer-aided detection (CAD) system for the detection of small AIH would facilitate timely diagnosis. A previously developed 2D algorithm shows high false positive rates in the evaluation based on LAC/USC cases, due to the limitation of setting up correct coordinate system for the knowledge-based classification system. To achieve a higher sensitivity and specificity, a new 3D algorithm is developed. The algorithm utilizes a top-hat transformation and dynamic threshold map to detect small AIH lesions. Several key structures of brain are detected and are used to set up a 3D anatomical coordinate system. A rule-based classification of the lesion detected is applied based on the anatomical coordinate system. For convenient evaluation in clinical environment, the CAD module is integrated with a stand-alone system. The CAD is evaluated by small AIH cases and matched normal collected in LAC/USC. The result of 3D CAD and the previous 2D CAD has been compared.

Free-Standing Air Cathodes Based on 3D Hierarchically Porous Carbon Membranes: Kinetic Overpotential of Continuous Macropores in Li-O2 Batteries.

PubMed

Xu, Shu-Mao; Liang, Xiao; Ren, Zhi-Chu; Wang, Kai-Xue; Chen, Jie-Sheng

2018-06-04

Free-standing macroporous air electrodes with enhanced interfacial contact, rapid mass transport, and tailored deposition space for large amounts of Li 2 O 2 are essential for improving the rate performance of Li-O 2 batteries. An ordered mesoporous carbon membrane with continuous macroporous channels was prepared by inversely topological transformation from ZnO nanorod array. Utilized as a free-standing air cathode for Li-O 2 battery, the hierarchically porous carbon membrane shows superior rate performance. However, the increased cross-sectional area of the continuous macropores on the cathode surface leads to a kinetic overpotential with large voltage hysteresis and linear voltage variation against Butler-Volmer behavior. The kinetics were investigated based on the rate-determining step of second electron transfer accompanied by migration of Li + in solid or quasi-solid intermediates. These discoveries shed light on the design of the air cathode for Li-O 2 batteries with high-rate performance. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ultrasonic alignment of microparticles in nozzle-like geometries

NASA Astrophysics Data System (ADS)

Whittaker, Molly A.; Dauson, Erin R.; Parra-Raad, Jaime; Heard, Robert A.; Oppenheim, Irving J.

2018-03-01

Additive manufacturing (3-D printing) is presently limited by the mechanical properties of the materials, such as polymer resins, that are otherwise efficient and economical for part-forming. Reinforcing the resin with microscale fibers and/or particles would be an effective mechanism to achieve desired mechanical properties such as strength and ductility. Our work combines standing wave ultrasonics and microfluidics to align microparticles in devices that can act as print nozzles, based in part on our prior work with cell sorting. In this paper three different approaches are presented illustrating different engineering tradeoffs, and demonstrating laboratory results of particle alignment. First acoustic resonators are discussed, in which the ultrasonic standing waves result mostly from the mechanical properties of the microfluidic structure, excited by a piezoceramic transducer. Next non-resonant microfluidic structures are discussed, in which ultrasonic standing waves are produced directly by symmetrical transducer deployment. Finally, devices that combine nozzle-like structures, which themselves are suitable acoustic resonators, subjected to symmetrical ultrasonic excitation are presented. We will show that all three configurations will align microparticles, and discuss the tradeoffs among them for subsequent configuration of a print nozzle.

An examination of factors influencing the spatial distribution of foraging bats in pine stands in the southeastern United States.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menzel, Michael, A., Jr.

Menzel, M.A. 2003. An examination of factors influencing the spatial distribution of foraging bats in pine stands in the Southeastern United States. Ph.D Dissertation. Davis College of Agriculture, Forestry and Consumer Sciences at West Virginia University, Morgantown, West Virginia. 336 pp. The general objective of this dissertation was to determine the effect of changes in forest structure on bat activity patterns in southern pine stands. Four sub studies are included in the dissertation: (1) An examination of the homerange size, habitat use and diet of four reproductively active male Rafinesque's big eared bats (Corynorhimus rafinesquii); (2) An examination of themore » diet of 5 reproductively active male Rafinesque's big eared bats; (3) A comparison of bat activity levels in the Coastal Plain of South Carolina among 5 vegetational community types: forested riparian areas, clearcuts, young pine plantations, mature plantations, and pine savannahs; (4) A summarization of information concerning the natural history of all bat species common in the SPR.« less

Comprehensive joint feedback control for standing by functional neuromuscular stimulation-a simulation study.

PubMed

Nataraj, Raviraj; Audu, Musa L; Kirsch, Robert F; Triolo, Ronald J

2010-12-01

Previous investigations of feedback control of standing after spinal cord injury (SCI) using functional neuromuscular stimulation (FNS) have primarily targeted individual joints. This study assesses the potential efficacy of comprehensive (trunk, hips, knees, and ankles) joint feedback control against postural disturbances using a bipedal, 3-D computer model of SCI stance. Proportional-derivative feedback drove an artificial neural network trained to produce muscle excitation patterns consistent with maximal joint stiffness values achievable about neutral stance given typical SCI muscle properties. Feedback gains were optimized to minimize upper extremity (UE) loading required to stabilize against disturbances. Compared to the baseline case of maximum constant muscle excitations used clinically, the controller reduced UE loading by 55% in resisting external force perturbations and by 84% during simulated one-arm functional tasks. Performance was most sensitive to inaccurate measurements of ankle plantar/dorsiflexion position and hip ab/adduction velocity feedback. In conclusion, comprehensive joint feedback demonstrates potential to markedly improve FNS standing function. However, alternative control structures capable of effective performance with fewer sensor-based feedback parameters may better facilitate clinical usage.

Seasat synthetic aperture radar /SAR/ response to lowland vegetation types in eastern Maryland and Virginia

NASA Technical Reports Server (NTRS)

Krohn, M. D.; Milton, N. M.; Segal, D. B.

1983-01-01

Examination of Seasat SAR images of eastern Maryland and Virginia reveals botanical distinctions between vegetated lowland areas and adjacent upland areas. Radar returns from the lowland areas can be either brighter or darker than returns from the upland forests. Scattering models and scatterometer measurements predict an increase of 6 dB in backscatter from vegetation over standing water. This agrees with the 30-digital number (DN) increase observed in the digital Seasat data. The brightest areas in the Chickahominy, Virginia, drainage, containing P. virginica about 0.4 m high, contrast with the brightest areas in the Blackwater, Maryland, marshes, which contain mature loblolly pine in standing water. The darkest vegetated area in the Chickahominy drainage contains a forest of Nyssa aquatica (water tupelo) about 18 m high, while the darkest vegetated area in the Blackwater marshes contains the marsh plant Spartina alterniflora, 0.3 m high. The density, morphology, and relative geometry of the lowland vegetation with respect to standing water can all affect the strength of the return L band signal.

From 1D Polymers to 2D Polymers: Preparation of Free-Standing Single-Monomer-Thick Two-Dimensional Conjugated Polymers in Water.

PubMed

Zhang, Na; Wang, Taisheng; Wu, Xing; Jiang, Chen; Zhang, Taiming; Jin, Bangkun; Ji, Hengxing; Bai, Wei; Bai, Ruke

2017-07-25

Recently, investigation on two-dimensional (2D) organic polymers has made great progress, and conjugated 2D polymers already play a dynamic role in both academic and practical applications. However, a convenient, noninterfacial approach to obtain single-layer 2D polymers in solution, especially in aqueous media, remains challenging. Herein, we present a facile, highly efficient, and versatile "1D to 2D" strategy for preparation of free-standing single-monomer-thick conjugated 2D polymers in water without any aid. The 2D structure was achieved by taking advantage of the side-by-side self-assembly of a rigid amphiphilic 1D polymer and following topochemical photopolymerization in water. The spontaneous formation of single-layer polymer sheets was driven by synergetic association of the hydrophobic interactions, π-π stacking interactions, and electrostatic repulsion. Both the supramolecular sheets and the covalent sheets were confirmed by spectroscopic analyses and electron microscope techniques. Moreover, in comparison of the supramolecular 2D polymer, the covalent 2D polymer sheets exhibited not only higher mechanical strength but also higher conductivity, which can be ascribed to the conjugated network within the covalent 2D polymer sheets.

Monitoring of environmental conditions in taiga forests using ERS-1 SAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rignot, E.; Way, J.B.; McDonald, K.

1994-08-01

Synthetic-aperture radar images of forest site near Manley Hot Springs (64[degree]N, 151[degree]W), Alaska, were collected between August 1991 and December 1991, day and night, every 3 days, at C-band frequency ([lambda] = 5.7 cm), vertical receive and transmit polarization, by the European Space Agency First Remote Sensing Satellite, ERS-1. During the same period, air and soil temperatures and dielectric and gravimetric moisture properties of the forest canopy and forest floor were monitored in three forest stands dominated, respectively, by black spruce (Picea mariana), white spruce (Picea glauca), and balsam poplar (Populus balsamifera). The calibrated ERS-1 radar backscatter values, [sigma][degree], ofmore » the forest stands are shown to exhibit a pronounced temporal pattern, with little separability between tree species. The largest change in [sigma][degree], a 3-dB decrease almost independent of tree species, is observed in early winter when the soil and vegetation freeze. In the summer, temporal fluctuations in [sigma][degree] are about 1--2 dB in magnitude, depending on tree species. Diurnal variations in [sigma][degree] are as large as 2 dB during fall freeze-up, and less than 1 dB in summer and winter. These temporal variations in radar backscatter from the forest are interpreted using the MIMICS radar backscatter model and the in situ surface observations as due to changes in the dielectric properties of the forest floor and forest canopy induced by precipitation (summer), drought (fall), and freezing (fall-winter) events. In winter, [sigma][degree] increases across the entire landscape, probably because of volume scattering from large depth hoar ice crystals forming in the snow pack.« less

Using LiDAR data to measure the 3D green biomass of Beijing urban forest in China.

PubMed

He, Cheng; Convertino, Matteo; Feng, Zhongke; Zhang, Siyu

2013-01-01

The purpose of the paper is to find a new approach to measure 3D green biomass of urban forest and to testify its precision. In this study, the 3D green biomass could be acquired on basis of a remote sensing inversion model in which each standing wood was first scanned by Terrestrial Laser Scanner to catch its point cloud data, then the point cloud picture was opened in a digital mapping data acquisition system to get the elevation in an independent coordinate, and at last the individual volume captured was associated with the remote sensing image in SPOT5(System Probatoired'Observation dela Tarre)by means of such tools as SPSS (Statistical Product and Service Solutions), GIS (Geographic Information System), RS (Remote Sensing) and spatial analysis software (FARO SCENE and Geomagic studio11). The results showed that the 3D green biomass of Beijing urban forest was 399.1295 million m(3), of which coniferous was 28.7871 million m(3) and broad-leaf was 370.3424 million m(3). The accuracy of 3D green biomass was over 85%, comparison with the values from 235 field sample data in a typical sampling way. This suggested that the precision done by the 3D forest green biomass based on the image in SPOT5 could meet requirements. This represents an improvement over the conventional method because it not only provides a basis to evalue indices of Beijing urban greenings, but also introduces a new technique to assess 3D green biomass in other cities.

Using LiDAR Data to Measure the 3D Green Biomass of Beijing Urban Forest in China

PubMed Central

He, Cheng; Convertino, Matteo; Feng, Zhongke; Zhang, Siyu

2013-01-01

The purpose of the paper is to find a new approach to measure 3D green biomass of urban forest and to testify its precision. In this study, the 3D green biomass could be acquired on basis of a remote sensing inversion model in which each standing wood was first scanned by Terrestrial Laser Scanner to catch its point cloud data, then the point cloud picture was opened in a digital mapping data acquisition system to get the elevation in an independent coordinate, and at last the individual volume captured was associated with the remote sensing image in SPOT5(System Probatoired'Observation dela Tarre)by means of such tools as SPSS (Statistical Product and Service Solutions), GIS (Geographic Information System), RS (Remote Sensing) and spatial analysis software (FARO SCENE and Geomagic studio11). The results showed that the 3D green biomass of Beijing urban forest was 399.1295 million m3, of which coniferous was 28.7871 million m3 and broad-leaf was 370.3424 million m3. The accuracy of 3D green biomass was over 85%, comparison with the values from 235 field sample data in a typical sampling way. This suggested that the precision done by the 3D forest green biomass based on the image in SPOT5 could meet requirements. This represents an improvement over the conventional method because it not only provides a basis to evalue indices of Beijing urban greenings, but also introduces a new technique to assess 3D green biomass in other cities. PMID:24146792

STS-63 Crew Portrait

NASA Technical Reports Server (NTRS)

1994-01-01

Crew members assigned to the STS-63 mission included (front left to right) Janice E. Voss, mission specialist; Eileen M. Collins, pilot; (the first woman to pilot a Space Shuttle), James D. Wetherbee, commander; and Vladmir G. Titov (Cosmonaut). Standing in the rear are mission specialists Bernard A. Harris, and C. Michael Foale. Launched aboard the Space Shuttle Discovery on February 3, 1995 at 12:22:04 am (EST), the primary payload for the mission was the SPACEHAB-3. STS-63 marked the first approach and fly around by the Shuttle with the Russian space station Mir.

Combinatorial Geometry Computer Models of Sitting and Standing Crew Personnel

DTIC Science & Technology

1981-08-01

Anthropometry - 1976,11 US Army Natick Laboratories Technical Report No. 72-51-CE, December, 1971. 10 4-). 0 4-3 4-3 =- -mr - 4. . 0 C- 4- WW~ C0 0 4...t.4IwI-4S-4 4A Vs x 1-4~ i-I a~ 4 >- *E0. .- ~-- I- u ~.Iz 4 www ou u0 W(. cc 0 I- I-W OW(AWWW Wj oz 0 WW4 X XL U. WEE.-J. d- 1.4 o ZZ W W w LL to4W0

TODS BioCast User Manual, Forecasting 3D Satellite Derived Optical Properties Using Eulerian Advection Procedure, Version 1.0

DTIC Science & Technology

2015-06-17

Example 2: OpCast_cron.sh #!/bin/sh # # # # # Cron helper script This script may be called with the appropriate arguments to reproduce what the...testing. Example 3: OpCast.sh #!/bin/sh # # helper script to set up environment for call to make_merged_product.sh # # This script can be called stand...ecosystem model skill assessment, Journal of Marine Systems, 76(1-2), 64-82, doi:10.1016/j.jmarsys.2008.05.014. Jolliff, J. K., S. Ladner, R. Crout, P

TSA Should Stand for 'Thank Servicemembers Appropriately' | DoDLive

Science.gov Websites

civilians, Military Children, Transportation Security Administration, TSA. Bookmark the permalink. Comments children coalition forces Defense Department of Defense deployed deployment DoD DoD News families family

Three-dimensional carbon nanotubes for high capacity lithium-ion batteries

NASA Astrophysics Data System (ADS)

Kang, Chiwon; Patel, Mumukshu; Rangasamy, Baskaran; Jung, Kyu-Nam; Xia, Changlei; Shi, Sheldon; Choi, Wonbong

2015-12-01

Carbon nanotubes (CNTs) have been considered as a potential anode material for next generation Lithium-ion batteries (LIBs) due to their high conductivity, flexibility, surface area, and lithium-ion insertion ability. However, the low mass loading and bulk density of carbon nanomaterials hinder their use in large-scale energy storage because their high specific capacity may not scale up linearly with the thickness of the electrode. To address this issue, a novel three-dimensional (3D) architecture is rationally designed by stacking layers of free-standing CNTs with the increased areal density to 34.9 mg cm-2, which is around three-times higher than that of the state-of-the-art graphitic anodes. Furthermore, a thermal compression process renders the bulk density of the multi-stacked 3D CNTs to be increased by 1.85 g cm-3, which yields an excellent volumetric capacity of 465 mAh cm-3 at 0.5C. Our proposed strategy involving the stacking of 3D CNT based layers and post-thermal compression provides a powerful platform for the utilization of carbon nanomaterials in the advanced LIB technology.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manley, M. E.; Abernathy, D. L.; Sahul, R.

A long-standing controversy for relaxor ferroelectrics has been the origin of the waterfall effect in the phonon dispersion curves, in which low-energy transverse phonons cascade into vertical columns. Originally interpreted as phonons interacting with polar nanoregions (PNRs), it was later explained as an interference effect of coupling damped optic and acoustic phonons. In light of a recently discovered PNR vibrational mode near the waterfall wavevector [M. E. Manley, J. W. Lynn, D. L. Abernathy, E. D. Specht, O. Delaire, A. R. Bishop, R. Sahul, and J. D. Budai, Nat. Commun. 5, 3683 (2014)] we have reexamined this feature using neutronmore » scattering on [100]-poled PMN-30%PT (0.6Pb(Mg 1/3Nb 2/3)O 3 0.3PbTiO 3). In addition, we find that the PNR mode couples to both optic and acoustic phonons, and that this results in complex patterns in the dynamic structure factor, including intensity pockets and peaks localized in momentum-energy space. These features are fully explained by extending the mode-coupling model to include three coupled damped harmonic oscillators representing the transverse optic, acoustic, and PNR modes.« less

Effects of foot posture on fifth metatarsal fracture healing: a finite element study.

PubMed

Brilakis, Emmanuel; Kaselouris, Evaggelos; Xypnitos, Frank; Provatidis, Christopher G; Efstathopoulos, Nicolas

2012-01-01

The goal of this study was to evaluate the effects of maintaining different foot postures during healing of proximal fifth metatarsal fractures for each of 3 common fracture types. A 3-dimensional (3D) finite element model of a human foot was developed and 3 loading situations were evaluated, including the following: (1) normal weightbearing, (2) standing with the affected foot in dorsiflexion at the ankle, and (3) standing with the affected foot in eversion. Three different stages of the fracture-healing process were studied, including: stage 1, wherein the material interposed between the fractured edges was the initial connective tissue; stage 2, wherein connective tissue had been replaced by soft callus; and stage 3, wherein soft callus was replaced by mature bone. Thus, 30 3D finite element models were analyzed that took into account fracture type, foot posture, and healing stage. Different foot postures did not statistically significantly affect the peak-developed strains on the fracture site. When the fractured foot was everted or dorsiflexed, it developed a slightly higher strain within the fracture than when it was in the normal weightbearing position. In Jones fractures, eversion of the foot caused further torsional strain and we believe that this position should be avoided during foot immobilization during the treatment of fifth metatarsal base fractures. Tuberosity avulsion fractures and Jones fractures seem to be biomechanically stable fractures, as compared with shaft fractures. Our understanding of the literature and experience indicate that current clinical observations and standard therapeutic options are in accordance with the results that we observed in this investigation, with the exception of Jones fractures. Copyright © 2012 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

CSG delivery and installation

NASA Image and Video Library

2010-10-27

The first of nine chemical steam generator (CSG) units that will be used on the A-3 Test Stand is hoisted into place at the E-2 Test Stand at John C. Stennis Space Center on Oct. 24, 2010. The unit was installed at the E-2 stand for verification and validation testing before it is moved to the A-3 stand. Steam generated by the nine CSG units that will be installed on the A-3 stand will create a vacuum that allows Stennis operators to test next-generation rocket engines at simulated altitudes up to 100,000 feet.

Differential and relaxed image foresting transform for graph-cut segmentation of multiple 3D objects.

PubMed

Moya, Nikolas; Falcão, Alexandre X; Ciesielski, Krzysztof C; Udupa, Jayaram K

2014-01-01

Graph-cut algorithms have been extensively investigated for interactive binary segmentation, when the simultaneous delineation of multiple objects can save considerable user's time. We present an algorithm (named DRIFT) for 3D multiple object segmentation based on seed voxels and Differential Image Foresting Transforms (DIFTs) with relaxation. DRIFT stands behind efficient implementations of some state-of-the-art methods. The user can add/remove markers (seed voxels) along a sequence of executions of the DRIFT algorithm to improve segmentation. Its first execution takes linear time with the image's size, while the subsequent executions for corrections take sublinear time in practice. At each execution, DRIFT first runs the DIFT algorithm, then it applies diffusion filtering to smooth boundaries between objects (and background) and, finally, it corrects possible objects' disconnection occurrences with respect to their seeds. We evaluate DRIFT in 3D CT-images of the thorax for segmenting the arterial system, esophagus, left pleural cavity, right pleural cavity, trachea and bronchi, and the venous system.

Translational Development and Application of (1→3)-β-d-Glucan for Diagnosis and Therapeutic Monitoring of Invasive Mycoses

PubMed Central

McCarthy, Matthew W.; Petraitiene, Ruta; Walsh, Thomas J.

2017-01-01

Early diagnosis and prompt initiation of appropriate antimicrobial therapy are crucial steps in the management of patients with invasive fungal infections. However, the diagnosis of invasive mycoses remains a major challenge in clinical practice, because presenting symptoms may be subtle and non-invasive diagnostic assays often lack sensitivity and specificity. Diagnosis is often expressed on a scale of probability (proven, probable and possible) based on a constellation of imaging findings, microbiological tools and histopathology, as there is no stand-alone assay for diagnosis. Recent data suggest that the carbohydrate biomarker (1→3)-β-d-glucan may be useful in both the diagnosis and therapeutic monitoring of invasive fungal infections due to some yeasts, molds, and dimorphic fungi. In this paper, we review recent advances in the use of (1→3)-β-d-glucan to monitor clinical response to antifungal therapy and explore how this assay may be used in the future. PMID:28538702

Channel add-drop filter based on dual photonic crystal cavities in push-pull mode.

PubMed

Poulton, Christopher V; Zeng, Xiaoge; Wade, Mark T; Popović, Miloš A

2015-09-15

We demonstrate an add-drop filter based on a dual photonic crystal nanobeam cavity system that emulates the operation of a traveling wave resonator, and, thus, provides separation of the through and drop port transmission from the input port. The device is on a 3×3  mm chip fabricated in an advanced microelectronics silicon-on-insulator complementary metal-oxide semiconductor (SOI CMOS) process (IBM 45 nm SOI) without any foundry process modifications. The filter shows 1 dB of insertion loss in the drop port with a 3 dB bandwidth of 64 GHz, and 16 dB extinction in the through port. To the best of our knowledge, this is the first implementation of a port-separating, add-drop filter based on standing wave cavities coupled to conventional waveguides, and demonstrates a performance that suggests potential for photonic crystal devices within optical immersion lithography-based advanced CMOS electronics-photonics integration.

Spatially oriented plasmonic ‘nanograter’ structures

PubMed Central

Liu, Zhe; Cui, Ajuan; Gong, Zhijie; Li, Hongqiang; Xia, Xiaoxiang; Shen, Tiehan H.; Li, Junjie; Yang, Haifang; Li, Wuxia; Gu, Changzhi

2016-01-01

One of the key motivations in producing 3D structures has always been the realization of metamaterials with effective constituent properties that can be tuned in all propagation directions at various frequencies. Here, we report the investigation of spatially oriented “Nanograter” structures with orientation-dependent responses over a wide spectrum by focused-ion-beam based patterning and folding of thin film nanostructures. Au nano units of different shapes, standing along specifically designated orientations, were fabricated. Experimental measurements and simulation results show that such structures offer an additional degree of freedom for adjusting optical properties with the angle of inclination, in additional to the size of the structures. The response frequency can be varied in a wide range (8 μm–14 μm) by the spatial orientation (0°–180°) of the structures, transforming the response from magnetic into electric coupling. This may open up prospects for the fabrication of 3D nanostructures as optical interconnects, focusing elements and logic elements, moving toward the realization of 3D optical circuits. PMID:27357610

JS-MS: a cross-platform, modular javascript viewer for mass spectrometry signals.

PubMed

Rosen, Jebediah; Handy, Kyle; Gillan, André; Smith, Rob

2017-11-06

Despite the ubiquity of mass spectrometry (MS), data processing tools can be surprisingly limited. To date, there is no stand-alone, cross-platform 3-D visualizer for MS data. Available visualization toolkits require large libraries with multiple dependencies and are not well suited for custom MS data processing modules, such as MS storage systems or data processing algorithms. We present JS-MS, a 3-D, modular JavaScript client application for viewing MS data. JS-MS provides several advantages over existing MS viewers, such as a dependency-free, browser-based, one click, cross-platform install and better navigation interfaces. The client includes a modular Java backend with a novel streaming.mzML parser to demonstrate the API-based serving of MS data to the viewer. JS-MS enables custom MS data processing and evaluation by providing fast, 3-D visualization using improved navigation without dependencies. JS-MS is publicly available with a GPLv2 license at github.com/optimusmoose/jsms.

Space Shuttle Projects

NASA Image and Video Library

1990-07-08

The official STS-38 crew portrait includes the following 5 astronauts (front left to right): Frank L. Culbertson, pilot; and Richard O. Covey, commander. Standing (left to right) are mission specialists (MS) Charles D. (Sam) Gemar, (MS-3), Robert C. Springer, (MS-1), and Carl J. Meade, (MS-2). The seventh mission dedicated to the Department of Defense (DOD), the STS-38 crew launched aboard the Space Shuttle Atlantis on November 15, 1990 at 6:48:15 pm (EST).

Energy Forecasting Models Within the Department of the Navy.

DTIC Science & Technology

1982-06-01

standing the climatic conditions responsible for the results. Both models have particular advantages in parti- cular applications and will be examined...and moving average processes. A similar notation for a model with seasonality . .- considerations will be ARIMA (p d j)(P Q) 3=12, where the upper...AD-A12l 950 ENERGY FORECASTING MODELS WITHIN THE DEPARTMENT OF THE 1/4 NAYY(U) NAVAL POSTGRADUATE SCHOOL MONTEREY CA L &I BUTTOIPH JUN 82

NASA Conducts Final RS-25 Rocket Engine Test of 2017

NASA Image and Video Library

2017-12-13

NASA engineers at Stennis Space Center capped a year of Space Launch System testing with a final RS-25 rocket engine hot fire on Dec. 13. The 470-second test on the A-1 Test Stand was a “green run” test of an RS-25 flight controller. The engine tested also included a large 3-D-printed part, a pogo accumulator assembly, scheduled for use on future RS-25 flight engines.

Medical Civic Action Programs (MEDCAPS) and Medical Readiness Training Exercises (MEDRETES) as Instruments of Foreign Policy

DTIC Science & Technology

1988-05-24

term for their program, namely GUARDE, which stands for Guiar de Assistancia Resistancia De Enfermedades (Guided Assistance to Resistance to Sickness...Measles, Tetanus, Toxoid,- BCG). 2. Tuberculosis 3. C.E.D. (Control de Enfermedades Diarreicas) Control of Diarrhea (Oral Rehidration) 4. I.R.A...Infecciones Respiratorias Agudas) Acute Respiratory Infections ,. 5. Rabia . Rabies -control " 6.. .T. S.-.( Enfermedades de Transmisi6n Sexual) S ", -T

Three- and Two-Dimensional Tin and Lead Halide Perovskite Semiconductors: Synthesis and Application in Photovoltaics

NASA Astrophysics Data System (ADS)

Cao, Duyen Hanh

Halide perovskites, AMX3 (A = monocation, B = Ge, Sn, or Pb, and X = halogen), present a versatile class of solution-processable semiconductors made from earth abundant materials with outstanding electrical and optical properties. Their solar cell efficiencies have dramatically increased from 9% to 22% in less than five years since 2012, a rate that has never been seen before in photovoltaic research. Critical to the final goal of commercializing perovskite solar cell technology is achieving device long-term stability and eliminating toxic elements in device components. This thesis uses 3D AMX 3 perovskites as a stand-in to develop a new class of lead-free, moisture stable, functional and highly tunable 2D Ruddlesden-Popper (BA) 2(MA)n-1SnnI3n+1 (n is an integer) perovskite semiconductors. Synthesis, thin film fabrication, extensive characterization, and solar cell device structure-performance relationships are presented throughout the entire thesis.

Forest restoration at Redwood National Park: exploring prescribed fire alternatives to second-growth management: a case study

Treesearch

Eamon Engber; Jason Teraoka; Phil van Mantgem

2017-01-01

Almost half of Redwood National Park is comprised of second-growth forests characterized by high stand density, deficient redwood composition, and low understory biodiversity. Typical structure of young redwood stands impedes the recovery of old-growth conditions, such as dominance of redwood (Sequoia sempervirens (D. Don) Endl.), distinct...

Slash and litter weight after clearcut logging in two young-growth timber stands

Treesearch

William E. Sundahl

1966-01-01

Ninety-year-old stands of the Pacific ponderosa pine and Pacific ponderosa pine-Douglas-fir types yielded 53 to 110 tons of slash to the acre after logging on the Challenge Experimental Forest, Yuba County, Calif. Fine slash (under 4 inches d.i.b.) contributed 61 to 64 percent of this weight.

Thinning stagnated ponderosa and Jeffrey pine stands in northeastern California: 30-year effects

Treesearch

Robert J. Lilieholm; Dennis E. Teeguarden; Donald T. Gordon

1989-01-01

Response to precommercial thinning in stagnated 55-year-old ponderosa (Pinus ponderosa Dougl. ex Laws.) and Jeffrey pine (P. jeffreyi Grev. and Balf.) stands in northeastern alifornia was rapid and long-lasting. During the first 5 years after thinning, average annual diameter at breast height (d.b.h.) and height growth of trees on...

Stem volume losses in grand firs topkilled by western spruce budworm in Idaho

Treesearch

George T. Ferrell; Robert F. Scharpf

1982-01-01

Mature grand firs (Abies grandis [Dougl. ex D. Don] Lindl.) were sampled in two stands, one cutover and one virgin, in the Little Salmon River drainage in west-central Idaho, to estimate stem volume losses associated with topkilling. Damage to the stands resulted from three outbreaks of western spruce budworm (Choristoneura occidentalis...

Association of Vitamin K Status Combined With Vitamin D Status and Lower-Extremity Function: A Prospective Analysis of Two Knee Osteoarthritis Cohorts.

PubMed

Shea, M Kyla; Loeser, Richard F; McAlindon, Timothy E; Houston, Denise K; Kritchevsky, Stephen B; Booth, Sarah L

2017-10-17

Vitamins K and D are important for the function of vitamin K-dependent proteins in joint tissues. It is unclear whether these nutrients are mutually important to functional outcomes related to knee osteoarthritis (OA). We evaluated the association of vitamin K and D sufficiency with lower-extremity function in the Health, Aging and Body Composition knee OA substudy (Health ABC) and conducted a replication analysis in an independent cohort, the Osteoarthritis Initiative (OAI). In Health ABC (60% female, mean ± SD age 75 ± 3 years) baseline nutrient status was measured using circulating vitamin K and 25-hydroxyvitamin D (25[OH]D). Lower-extremity function was assessed using the Short Physical Performance Battery (SPPB) and usual 20-meter gait speed. In the OAI (58% female, mean ± SD age 61 ± 9 years), baseline nutrient intake was estimated by food frequency questionnaire. Lower-extremity function was assessed using usual 20-meter gait speed and chair stand completion time. Multivariate mixed models were used to evaluate the association of vitamin K and D status and intake with lower-extremity function over 4-5 years. Health ABC participants with sufficient plasma vitamin K (≥1.0 nmoles/liter) and serum 25(OH)D (≥50 nmoles/liter) generally had better SPPB scores and faster usual gait speed over followup (P ≤ 0.002). In the OAI, sufficient vitamin K and vitamin D intake combined was associated with overall faster usual gait speed and chair stand completion time over followup (P ≤ 0.029). Sufficient vitamin K status combined with sufficient vitamin D status was associated with better lower-extremity function in 2 knee OA cohorts. These findings merit confirmation in vitamin K and D co-supplementation trials. © 2017, American College of Rheumatology.

STS-98 Flight Control Team Photo in the WFCR

NASA Image and Video Library

2001-01-08

JSC2001-00001 (January 2001) --- The STS-98 astronaut crew poses with about five dozen flight controllers making up its ascent/entry team in the shuttle flight control room of the Johnson Space Center's Mission Control Center (MCC). Standing with the STS-98 insignia is flight director LeRoy Cain. He is flanked by astronauts Marsha S. Ivins, mission specialist, and Kenneth D. Cockrell, mission commander. Behind Cockrell is astronaut Robert L. Curbeam, Jr., mission specialist; and behind Ivins and Cain is astronaut Mark L. Polansky, pilot. Astronaut Thomas D. Jones, mission specialist (blue shirt) stands near the flight director sign. Astronaut Scott D. Altman, CAPCOM or Spacecraft Communicator, is immediately behind Cain. Launch is currently scheduled for February 6, 2001.

A-3 Test Stand work continues

NASA Image and Video Library

2011-04-22

Stennis Space Center employees continue work on the A-3 Test Stand test cell. The stand is being built to test next-generation rocket engines that could carry humans beyond low-Earth orbit into deep space.

Effect of softer flooring in tie stalls on resting behavior and leg injuries of lactating cows.

PubMed

Rushen, J; Haley, D; de Passillé, A M

2007-08-01

To test the advantages of softer flooring in tie stalls, we compared the behavior and injuries of dairy cows housed in tie stalls with either soft rubber mats (n = 12) or concrete flooring (n = 12), both lightly covered with straw. Data were collected for 112 d beginning at 14 DIM (+/-4 d). Cows' general activity was observed continuously for 24 h every 28 d. Behavior was also scored by a scan sampling technique every 14 d such that each cow was observed for a period of 3 min every 12 min. We scored the occurrence of leg lesions and other injuries every 7 d throughout the study. Cows on rubber mats had shorter bouts of lying but the frequency of bouts was higher, leading them to tend to spend more time lying compared with cows housed on concrete. Cows on concrete spent more time standing idle, but there was no difference in the time spent eating. There was no effect of stall flooring on the number of minor abrasions to the legs and body. There was a significantly higher incidence of swelling of the carpus joints for cows housed on concrete. Cows housed on soft rubber flooring appeared to be less hesitant to change posture from lying to standing (and vice versa), and as a result changed posture more frequently and spent more time lying than cows on concrete flooring. The decreased incidence of swelling of the carpus joint for cows on soft rubber mats may have important long-term effects in preventing a variety of leg problems.

Development of high intensity ion sources for a Tandem-Electrostatic-Quadrupole facility for Accelerator-Based Boron Neutron Capture Therapy.

PubMed

Bergueiro, J; Igarzabal, M; Sandin, J C Suarez; Somacal, H R; Vento, V Thatar; Huck, H; Valda, A A; Repetto, M; Kreiner, A J

2011-12-01

Several ion sources have been developed and an ion source test stand has been mounted for the first stage of a Tandem-Electrostatic-Quadrupole facility For Accelerator-Based Boron Neutron Capture Therapy. A first source, designed, fabricated and tested is a dual chamber, filament driven and magnetically compressed volume plasma proton ion source. A 4 mA beam has been accelerated and transported into the suppressed Faraday cup. Extensive simulations of the sources have been performed using both 2D and 3D self-consistent codes. Copyright © 2011 Elsevier Ltd. All rights reserved.

Heads-up 3D Microscopy: An Ergonomic and Educational Approach to Microsurgery

PubMed Central

Mendez, Bernardino M.; Chiodo, Michael V.; Vandevender, Darl

2016-01-01

Summary: Traditional microsurgery can lead surgeons to use postures that cause musculoskeletal fatigue, leaving them more prone to work-related injuries. A new technology from TrueVision transmits the microscopic image onto a 3-dimensional (3D) monitor, allowing surgeons to operate while sitting/standing in a heads-up position. The purpose of this study was to evaluate the feasibility of performing heads-up 3D microscopy as a more ergonomic alternative to traditional microsurgery. A feasibility study was conducted comparing heads-up 3D microscopy and traditional microscopy by performing femoral artery anastomoses on 8 Sprague-Dawley rats. Operative times and patency rates for each technology were compared. The 8 microsurgeons completed a questionnaire comparing image quality, comfort, technical feasibility, and educational value of the 2 technologies. Rat femoral artery anastomoses were successfully carried out by all 8 microsurgeons with each technology. There was no significant difference in anastomosis time between heads-up 3D and traditional microscopy (average times, 34.5 and 33.8 minutes, respectively; P = 0.66). Heads-up 3D microscopy was rated superior in neck and back comfort by 75% of participants. Image resolution, field of view, and technical feasibility were found to be superior or equivalent in 75% of participants, whereas 63% evaluated depth perception to be superior or equivalent. Heads-up 3D microscopy is a new technology that improves comfort for the microsurgeon without compromising image quality or technical feasibility. Its use has become prevalent in the field of ophthalmology and may also have utility in plastic and reconstructive surgery. PMID:27579241

Stem extension and mechanical stability of Xanthium canadense grown in an open or in a dense stand.

PubMed

Watari, Ryoji; Nagashima, Hisae; Hirose, Tadaki

2014-07-01

Plants in open, uncrowded habitats typically have relatively short stems with many branches, whereas plants in crowded habitats grow taller and more slender at the expense of mechanical stability. There seems to be a trade-off between height growth and mechanical stability, and this study addresses how stand density influences stem extension and consequently plant safety margins against mechanical failure. Xanthium canadense plants were grown either solitarily (S-plants) or in a dense stand (D-plants) until flowering. Internode dimensions and mechanical properties were measured at the metamer level, and the critical buckling height beyond which the plant elastically buckles under its own weight and the maximum lateral wind force the plant can withstand were calculated. Internodes were longer in D- than S-plants, but basal diameter did not differ significantly. Relative growth rates of internode length and diameter were negatively correlated to the volumetric solid fraction of the internode. Internode dry mass density was higher in S- than D-plants. Young's modulus of elasticity and the breaking stress were higher in lower metamers, and in D- than in S-plants. Within a stand, however, both moduli were positively related to dry mass density. The buckling safety factor, a ratio of critical buckling height to actual height, was higher in S- than in D-plants. D-plants were found to be approaching the limiting value 1. Lateral wind force resistance was higher in S- than in D-plants, and increased with growth in S-plants. Critical buckling height increased with height growth due mainly to an increase in stem stiffness and diameter and a reduction in crown/stem mass ratio. Lateral wind force resistance was enhanced due to increased tissue strength and diameter. The increase in tissue stiffness and strength with height growth plays a crucial role in maintaining a safety margin against mechanical failure in herbaceous species that lack the capacity for secondary growth. © The Author 2014. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Fabrications of some kinds of 2-D frameworks consisting of nanosized polyoxomolybdate anion [Mo 36O 112(H 2O) 16] 8- via condensation processes

NASA Astrophysics Data System (ADS)

Eda, Kazuo; Iriki, Yuichi; Kawamura, Kenjiro; Ikuki, Takeshi; Hayashi, Masahiko

2007-12-01

We succeeded to prepare novel [Mo 36O 112(H 2O) 16] 8- ({Mo 36}) compounds by using 1,3-diamino-2-propanol ( βOHC 3-DA) and 1,3,5-tris(aminomethyl)benzene (MES-TA)+1,3-diaminopropane (C 3-DA) as linkers, and determined their crystal structures. We have confirmed they have unique two-dimensional (2-D) molybdenum oxide frameworks, which are formed by condensation of {Mo 36}s. Side-staggered arrays of {Mo 36}s, connected in lying position by eight bridges per a {Mo 36}, are formed in the compound with βOHC 3-DA, while herringbone arrays of {Mo 36}s, connected in standing position by four bridges per a {Mo 36}, are built in the compound with MES-TA+C 3-DA. The latter compound exhibited non-stoichiometric property, and its composition and cell parameters varied depending on the relative concentration of MES-TA in the mother solution.

A-3 Test Stand work

NASA Image and Video Library

2011-07-29

Rocket engine propellant tanks and cell dome top the A-3 Test Stand under construction at Stennis Space Center. The stand will test next-generation rocket engines that could carry humans beyond low-Earth orbit into deep space once more.

Factors Affecting Planting Depth and Standing of Rice Seedling in Parachute Rice Transplanting

NASA Astrophysics Data System (ADS)

Astika, I. W.; Subrata, I. D. M.; Pramuhadi, G.

2018-05-01

Parachute rice transplanting is a simple and practical rice transplanting method. It can be done manually or mechanically, with various possible designs of machines or tools. This research aimed at quantitatively formulating related factors to the planting depth and standing of rice seedling. Parachute seedlings of rice were grown at several sizes of parachute soil bulb sizes. The trays were specially designed with a 3D printer having bulb sizes 7, 8, 9, 10 mm in square sides and 15 mm depth. At seedling ages of 8-12 days after sowing the seedling bulbs were drops into puddled soil. Soil hardness was set at 3 levels of hardness, measured in hardness index using golf ball test. Angle of dropping was set at 3 levels: 0°, 30°and 45° from the vertical axis. The height of droppings was set at 100 cm, 75 cm, and 50 cm. The relationship between bulb size, height of dropping, soil hardness, dropping angle and planting depth was formulated with ANN. Most of input variables did not significantly affect the planting depth, except that hard soil significantly differs from mild soil and soft soil. The dropping also resulted in various positions of the planted seedlings: vertical standing, sloped, and falling. However, at any position of the planted seedlings, the seedlings would recover themselves into normally vertical position. With this result, the design of planting machinery, as well as the manual planting operation, can be made easier.

Electrical impedance tomography in 3D using two electrode planes: characterization and evaluation.

PubMed

Wagenaar, Justin; Adler, Andy

2016-06-01

Electrical impedance tomography (EIT) uses body surface electrical stimulation and measurements to create conductivity images; it shows promise as a non-invasive technology to monitor the distribution of lung ventilation. Most applications of EIT have placed electrodes in a 2D ring around the thorax, and thus produced 2D cross-sectional images. These images are unable to distinguish out-of-plane contributions, or to image volumetric effects. Volumetric EIT can be calculated using multiple electrode planes and a 3D reconstruction algorithm. However, while 3D reconstruction algorithms are available, little has been done to understand the performance of 3D EIT in terms of the measurement configurations available. The goal of this paper is to characterize the phantom and in vivo performance of 3D EIT with two electrode planes. First, phantom measurements are used to measure the reconstruction characteristics of seven stimulation and measurement configurations. Measurements were then performed on eight healthy volunteers as a function of body posture, postures, and with various electrode configurations. Phantom results indicate that 3D EIT using two rings of electrodes provides reasonable resolution in the electrode plane but low vertical resolution. For volunteers, functional EIT images are created from inhalation curve features to analyze the effect of posture (standing, sitting, supine and decline) on regional lung behaviour. An ability to detect vertical changes in lung volume distribution was shown for two electrode configurations. Based on tank and volunteer results, we recommend the use of the 'square' stimulation and measurement pattern for two electrode plane EIT.

Automatic 3D virtual scenes modeling for multisensors simulation

NASA Astrophysics Data System (ADS)

Latger, Jean; Le Goff, Alain; Cathala, Thierry; Larive, Mathieu

2006-05-01

SEDRIS that stands for Synthetic Environment Data Representation and Interchange Specification is a DoD/DMSO initiative in order to federate and make interoperable 3D mocks up in the frame of virtual reality and simulation. This paper shows an original application of SEDRIS concept for research physical multi sensors simulation, when SEDRIS is more classically known for training simulation. CHORALE (simulated Optronic Acoustic Radar battlefield) is used by the French DGA/DCE (Directorate for Test and Evaluation of the French Ministry of Defense) to perform multi-sensors simulations. CHORALE enables the user to create virtual and realistic multi spectral 3D scenes, and generate the physical signal received by a sensor, typically an IR sensor. In the scope of this CHORALE workshop, French DGA has decided to introduce a SEDRIS based new 3D terrain modeling tool that enables to create automatically 3D databases, directly usable by the physical sensor simulation CHORALE renderers. This AGETIM tool turns geographical source data (including GIS facilities) into meshed geometry enhanced with the sensor physical extensions, fitted to the ray tracing rendering of CHORALE, both for the infrared, electromagnetic and acoustic spectrum. The basic idea is to enhance directly the 2D source level with the physical data, rather than enhancing the 3D meshed level, which is more efficient (rapid database generation) and more reliable (can be generated many times, changing some parameters only). The paper concludes with the last current evolution of AGETIM in the scope mission rehearsal for urban war using sensors. This evolution includes indoor modeling for automatic generation of inner parts of buildings.

Fludrocortisone does not prevent orthostatic hypotension in astronauts after spaceflight.

PubMed

Shi, Shang-Jin; South, Donna A; Meck, Janice V

2004-03-01

During stand/tilt tests after spaceflight, 20% of astronauts experience orthostatic hypotension and presyncope. Spaceflight-induced hypovolemia is a contributing factor. Fludrocortisone, a synthetic mineralocorticoid, has been shown to increase plasma volume and orthostatic tolerance in Earth-bound patients. The efficacy of fludrocortisone as a treatment for postflight hypovolemia and orthostatic hypotension in astronauts has not been studied. Our purpose was to test the hypothesis that astronauts who ingest fludrocortisone prior to landing would have less loss of plasma volume and greater orthostatic tolerance than astronauts who do not ingest fludrocortisone. There were 25 male astronauts who were randomized into 2 groups: placebo (n = 18) and fludrocortisone (n = 7), and participated in stand tests 10 d before launch and 2-4 h after landing. Subjects took either 0.3 mg fludrocortisone or placebo orally 7 h prior to landing. Supine plasma and red cell volumes, supine and standing HR, arterial pressure, aortic outflow, and plasma norepinephrine and epinephrine were measured. On landing day, 2 of 18 in the placebo group and 1 of 7 in the fludrocortisone group became presyncopal (chi2 = 0.015, p = 0.90). Plasma volumes were significantly decreased after flight in the placebo group, but not in the fludrocortisone group. During postflight stand tests, standing plasma norepinephrine was significantly less in the fludrocortisone group compared with the placebo group. Treatment with a single dose of fludrocortisone results in protection of plasma volume but no protection of orthostatic tolerance. Fludrocortisone is not recommended as a countermeasure for spaceflight-induced orthostatic intolerance.

Modeling tree crown dynamics with 3D partial differential equations.

PubMed

Beyer, Robert; Letort, Véronique; Cournède, Paul-Henry

2014-01-01

We characterize a tree's spatial foliage distribution by the local leaf area density. Considering this spatially continuous variable allows to describe the spatiotemporal evolution of the tree crown by means of 3D partial differential equations. These offer a framework to rigorously take locally and adaptively acting effects into account, notably the growth toward light. Biomass production through photosynthesis and the allocation to foliage and wood are readily included in this model framework. The system of equations stands out due to its inherent dynamic property of self-organization and spontaneous adaptation, generating complex behavior from even only a few parameters. The density-based approach yields spatially structured tree crowns without relying on detailed geometry. We present the methodological fundamentals of such a modeling approach and discuss further prospects and applications.

Saffman-Taylor Instability and the Inner Splitting Mechanism

NASA Astrophysics Data System (ADS)

Oliveira, Rafael; Meiburg, Eckart

2017-11-01

The classical miscible displacement experiments of Wooding (1969) exhibit an inner splitting phenomenon that remained unexplained for over 40 years. 3D Navier-Stokes simulations presented in, were the first ones to reproduce these experimental observations numerically, and to demonstrate that they are linked to concentrated streamwise vortices. The origin of these concentrated streamwise vortices remained a mystery, however. The current investigation, published at, finally resolves this long-standing issue. Towards this end, we compare 3D Navier-Stokes simulation results for neutrally buoyant, viscously unstable displacements and gravitationally unstable, constant viscosity ones. Only the former exhibit the generation of streamwise vorticity. The simulation results present conclusive evidence that it is caused by the lateral displacement of the more viscous fluid by the less viscous one, with the variable viscosity terms playing a dominant role.

Long-Term Cultures of Human Cornea Limbal Explants Form 3D Structures Ex Vivo - Implications for Tissue Engineering and Clinical Applications.

PubMed

Szabó, Dóra Júlia; Noer, Agate; Nagymihály, Richárd; Josifovska, Natasha; Andjelic, Sofija; Veréb, Zoltán; Facskó, Andrea; Moe, Morten C; Petrovski, Goran

2015-01-01

Long-term cultures of cornea limbal epithelial stem cells (LESCs) were developed and characterized for future tissue engineering and clinical applications. The limbal tissue explants were cultivated and expanded for more than 3 months in medium containing serum as the only growth supplement and without use of scaffolds. Viable 3D cell outgrowth from the explants was observed within 4 weeks of cultivation. The outgrowing cells were examined by immunofluorescent staining for putative markers of stemness (ABCG2, CK15, CK19 and Vimentin), proliferation (p63α, Ki-67), limbal basal epithelial cells (CK8/18) and differentiated cornea epithelial cells (CK3 and CK12). Morphological and immunostaining analyses revealed that long-term culturing can form stratified 3D tissue layers with a clear extracellular matrix deposition and organization (collagen I, IV and V). The LESCs showed robust expression of p63α, ABCG2, and their surface marker fingerprint (CD117/c-kit, CXCR4, CD146/MCAM, CD166/ALCAM) changed over time compared to short-term LESC cultures. Overall, we provide a model for generating stem cell-rich, long-standing 3D cultures from LESCs which can be used for further research purposes and clinical transplantation.

Estimation of tree root distribution using electrical resistivity tomography

NASA Astrophysics Data System (ADS)

Schmaltz, Elmar; Uhlemann, Sebastian

2016-04-01

Trees influence soil-mantled slopes mechanically by anchoring in the soil with coarse roots. Forest-stands play an important role in mechanical reinforcement to reduce the susceptibility to slope failures. However, the effect of stabilisation of roots is connected with the distribution of roots in the ground. The architecture and distribution of tree roots is diverse and strongly dependent on species, plant age, stand density, relief, nutrient supply as well as climatic and pedologic conditions. Particularly trees growing on inclined slopes show shape-shifting root systems. Geophysical techniques are commonly used to non-invasively study hydrological and geomorphological subsurface properties, by imaging contrasting physical properties of the ground. This also poses the challenge for geophysical imaging of root systems, as properties, such as electrical resistivity, of dry and wet roots fall within the range of soils. The objective of this study is whether electrical resistivity tomography (ERT) allows a reliable reproduction of root systems of alone-standing trees on diverse inclined slopes. In this regard, we set the focus on the branching of secondary roots of two common walnut trees (Juglans regia L.) that were not disturbed in the adjacencies and thus expected to develop their root systems unhindered. Walnuts show a taproot-cordate root system with a strong tap-root in juvenile age and a rising cordate rooting with increasing age. Hence, mature walnuts can exhibit a root system that appears to be deformed or shifted respectively when growing at hillslope locations. We employed 3D ERT centred on the tree stem, comprising dipole-dipole measurements on a 12-by-41 electrode grid with 0.5 m and 1.0m electrode spacing in x- and y-direction respectively. Data were inverted using a 3D smoothness constrained non-linear least-squares algorithm. First results show that the general root distribution can be estimated from the resistivity models and that shape-shifting effects of secondary roots of the two Juglans regia in differently inclined ambiences can be imaged using 3D ERT. The results of this study can yield a grasp about the dimension of root architecture of single trees by using non-invasive geophysical techniques and give evidence about how roots influence the soil mantle mechanically and hydrologically according to the spatial distribution of their coarse roots.

Thermodynamic Properties of AgIn2Te3I and AgIn2Te3Br, Determined by EMF Method

NASA Astrophysics Data System (ADS)

Moroz, M. V.; Prokhorenko, M. V.; Prokhorenko, S. V.; Yatskov, M. V.; Reshetnyak, O. V.

2018-01-01

Differential thermal analysis (DTA), X-ray diffraction (XRD), and electromotive force (EMF) are used to triangulate Ag-In-Te-I(Br) systems in the vicinity of compounds AgIn2Te3I and AgIn2Te3Br. The three-dimensional position of the AgIn2Te3I-InTe-Ag2Te-AgI and AgIn2Te3Br-InTe-Ag3TeBr phase areas with respect to the figurative points of silver is used to create equations of potential-determining chemical reactions. The potential-determining reactions are conducted in (-)C|Ag|Ag3GeS3I(Br) glass|D|C(+) electrochemical cells (ECCs), where C stands for inert (graphite) electrodes, Ag and D are ECC electrodes (D denotes alloys of one-, three-, and four-phase areas), and Ag3GeS3I and Ag3GeS3Br glasses are membranes with purely ionic Ag+ conductivity. Linear parts of the temperature dependences of the cell EMFs are used to calculate the standard integral thermodynamic functions of saturated solid solutions based on AgIn2Te3I and AgIn2Te3Br, and the relative partial thermodynamic functions of silver in the stoichiometric quaternary compounds.

3D Interconnected Carbon Fiber Network-Enabled Ultralong Life Na3 V2 (PO4 )3 @Carbon Paper Cathode for Sodium-Ion Batteries.

PubMed

Kretschmer, Katja; Sun, Bing; Zhang, Jinqiang; Xie, Xiuqiang; Liu, Hao; Wang, Guoxiu

2017-03-01

Sodium-ion batteries (NIBs) are an emerging technology, which can meet increasing demands for large-scale energy storage. One of the most promising cathode material candidates for sodium-ion batteries is Na 3 V 2 (PO 4 ) 3 due to its high capacity, thermal stability, and sodium (Na) Superionic Conductor 3D (NASICON)-type framework. In this work, the authors have significantly improved electrochemical performance and cycling stability of Na 3 V 2 (PO 4 ) 3 by introducing a 3D interconnected conductive network in the form of carbon fiber derived from ordinary paper towel. The free-standing Na 3 V 2 (PO 4 ) 3 -carbon paper (Na 3 V 2 (PO 4 ) 3 @CP) hybrid electrodes do not require a metallic current collector, polymeric binder, or conducting additives to function as a cathode material in an NIB system. The Na 3 V 2 (PO 4 ) 3 @CP cathode demonstrates extraordinary long term cycling stability for 30 000 deep charge-discharge cycles at a current density of 2.5 mA cm -2 . Such outstanding cycling stability can meet the stringent requirements for renewable energy storage. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Further Studies of Forest Structure Parameter Retrievals Using the Echidna® Ground-Based Lidar

NASA Astrophysics Data System (ADS)

Strahler, A. H.; Yao, T.; Zhao, F.; Yang, X.; Schaaf, C.; Wang, Z.; Li, Z.; Woodcock, C. E.; Culvenor, D.; Jupp, D.; Newnham, G.; Lovell, J.

2012-12-01

Ongoing work with the Echidna® Validation Instrument (EVI), a full-waveform, ground-based scanning lidar (1064 nm) developed by Australia's CSIRO and deployed by Boston University in California conifers (2008) and New England hardwood and softwood (conifer) stands (2007, 2009, 2010), confirms the importance of slope correction in forest structural parameter retrieval; detects growth and disturbance over periods of 2-3 years; provides a new way to measure the between-crown clumping factor in leaf area index retrieval using lidar range; and retrieves foliage profiles with more lower-canopy detail than a large-footprint aircraft scanner (LVIS), while simulating LVIS foliage profiles accurately from a nadir viewpoint using a 3-D point cloud. Slope correction is important for accurate retrieval of forest canopy structural parameters, such as mean diameter at breast height (DBH), stem count density, basal area, and above-ground biomass. Topographic slope can induce errors in parameter retrievals because the horizontal plane of the instrument scan, which is used to identify, measure, and count tree trunks, will intersect trunks below breast height in the uphill direction and above breast height in the downhill direction. A test of three methods at southern Sierra Nevada conifer sites improved the range of correlations of these EVI-retrieved parameters with field measurements from 0.53-0.68 to 0.85-0.93 for the best method. EVI scans can detect change, including both growth and disturbance, in periods of two to three years. We revisited three New England forest sites scanned in 2007-2009 or 2007-2010. A shelterwood stand at the Howland Experimental Forest, Howland, Maine, showed increased mean DBH, above-ground biomass and leaf area index between 2007 and 2009. Two stands at the Harvard Forest, Petersham, Massachusetts, suffered reduced leaf area index and reduced stem count density as the result of an ice storm that damaged the stands. At one stand, broken tops were visible in the 2010 point cloud canopy reconstruction. A new method for retrieval of the forest canopy between-crown clumping index from angular gaps in hemispherically-projected EVI data traces gaps as they narrow with range from the instrument, thus providing the approximate physical size, rather than angular size, of the gaps. In applying this method to a range of sites in the southern Sierra Nevada, element clumping index values are lower (more between-crown clumping effect) in more open stands, providing improved results as compared to conventional hemispherical photography. In dense stands with fewer gaps, the clumping index values were closer. Foliage profiles retrieved from EVI scans at five Sierra Nevada sites are closely correlated with those of the airborne Lidar Vegetation Imaging Sensor (LVIS) when averaged over a diameter of 100 m. At smaller diameters, the EVI scans have more detail in lower canopy layers and the LVIS and EVI foliage profiles are more distinct. Foliage profiles derived from processing 3-D site point clouds with a nadir view match the LVIS foliage profiles more closely than profiles derived from EVI in scan mode. Removal of terrain effects significantly enhances the match with LVIS profiles. This research was supported by the US National Science Foundation under grant MRI DBI-0923389.

A-3 Test Stand construction moves forward

NASA Image and Video Library

2010-07-13

Work on the A-3 Test Stand at Stennis Space Center took a step forward in July with delivery of the first-stage steam ejector July 13. Stennis employees are shown preparing the ejector to be lifted into place on the test stand. When activated in 2012, the A-3 Test Stand will allow operators to test rocket engines at simulated altitudes of 100,000 feet, a critical feature for next-generation engines that will take humans beyond low-Earth orbit once more.

Erection of a Centaur Standard Shroud at Plum Brook Station’s B-3 Test Stand

NASA Image and Video Library

1972-08-21

A section of the Centaur Standard Shroud transported to Nuclear Rocket Dynamics and Control Facility, or B-3 Test Stand, at the National Aeronautics and Space Administration’s (NASA) Plum Brook Station. B-3 was built in the early 1960s to test full-scale liquid hydrogen fuel systems in simulated altitude conditions. The facility was used in 1972, however, for testing of the Centaur Standard Shroud’s ejection system. In the late 1960s NASA engineers were planning the ambitious new Viking mission to send two rover vehicles to the surface of Mars. The Viking rovers were the heaviest payloads ever attempted and were over three times the weight of Atlas-Centaur’s previous heaviest payload. Consequently, NASA engineers selected the more powerful the Titan III rocket booster to mate with the Centaur. Concurrently, General Dynamics was in the process of introducing a new Centaur model for Titan—the D-1T. The biggest change for the D-1T was a completely new shroud designed by Lockheed, called the Centaur Standard Shroud. The shroud, its insulation, the Centaur ground-hold purge system, and the hydrogen tank venting system were all studied in B-3. After more than two years of preparations, the tests were run between April and July 1973. The tests determined the ultimate flight loads on two axes, established the Centaur’s load sharing, the level of propellant boiloff during launch holds, and the vent system capacity. The Centaur Standard Shroud performed flawlessly during the August 20 and September 9, 1975 launches of Viking 1 and 2.

Potential effects of forest management on surface albedo

NASA Astrophysics Data System (ADS)

Otto, J.; Bréon, F.-M.; Schelhaas, M.-J.; Pinty, B.; Luyssaert, S.

2012-04-01

Currently 70% of the world's forests are managed and this figure is likely to rise due to population growth and increasing demand for wood based products. Forest management has been put forward by the Kyoto-Protocol as one of the key instruments in mitigating climate change. For temperate and boreal forests, the effects of forest management on the stand-level carbon balance are reasonably well understood, but the biophysical effects, for example through changes in the albedo, remain elusive. Following a modeling approach, we aim to quantify the variability in albedo that can be attributed to forest management through changes in canopy structure and density. The modelling approach chains three separate models: (1) a forest gap model to describe stand dynamics, (2) a Monte-Carlo model to estimate the probability density function of the optical path length of photons through the canopy and (3) a physically-based canopy transfer model to estimate the interaction between photons and leaves. The forest gap model provides, on a monthly time step the position, height, diameter, crown size and leaf area index of individual trees. The Monte-Carlo model computes from this the probability density function of the distance a photon travels through crown volumes to determine the direct light reaching the forest floor. This information is needed by the canopy transfer model to calculate the effective leaf area index - a quantity that allows it to correctly represent a 3D process with a 1D model. Outgoing radiation is calculated as the result of multiple processes involving the scattering due to the canopy layer and the forest floor. Finally, surface albedo is computed as the ratio between incident solar radiation and calculated outgoing radiation. The study used two time series representing thinning from below of a beech and a Scots pine forest. The results show a strong temporal evolution in albedo during stand establishment followed by a relatively stable albedo once the canopy is closed. During this period, albedo is affected for a short time by forest operations. The modelling approach allowed us to estimate the importance of ground vegetation in the stand albedo. Given that ground vegetation depends on the light reaching the forest floor, ground vegetation could act as a natural buffer to dampen changes in albedo, allowing the stand to maintain optimal leaf temperature. Consequently, accounting for only the carbon balance component of forest management ignores albedo impacts and is thus likely to yield biased estimates of the climate benefits of forest ecosystems.

Six-year beechnut production in New Hampshire

Treesearch

William B. Leak; Raymond E. Graber; Raymond E. Graber

1993-01-01

Beechnut production and losses were studied over a 6-year period in 41 northern hardwood stands ranging in age from 10 to 140 years in the White Mountains of New Hampshire. Beechnut production increased consistently with stand age or d.b.h. of dominant trees and percentage of basal area composed of beech. Losses to insects, rodents, and birds before the seed reached...

Soil-active herbicides for single-stem and stand hardwood control

Treesearch

James H. Miller

1984-01-01

Four studies examined soil-active herbicides for control of hardwoods both as single-stems and in stands. The first study found that comparable control of sweetgum (Liquidambar styraciflua) was achieved both by tree injection using 2,4-D + picloram (Tordon 101R®) and by soil spot applications, using hexazinone (Velpar L®) and picloram (Tordon K®)...

Stand development following precommercial thinning and fertilization treatments in a western redcedar (Thuja plicata) dominated forest

Treesearch

Constance A. Harrington; Warren D. Devine

2011-01-01

Western redcedar (Thuja plicata Donn ex D. Don.) is an important North American tree species, but little information is available on its long-term responses to silvicultural treatments. Stand responses (mortality, ingrowth, basal area and volume growth, and distributions of trees by diameter and height classes) were followed for 25 years after...

Weighted linear regression using D2H and D2 as the independent variables

Treesearch

Hans T. Schreuder; Michael S. Williams

1998-01-01

Several error structures for weighted regression equations used for predicting volume were examined for 2 large data sets of felled and standing loblolly pine trees (Pinus taeda L.). The generally accepted model with variance of error proportional to the value of the covariate squared ( D2H = diameter squared times height or D...

Cumulative River Dynamic Assessment using Topo-Hydrographical High Definition Surveying in the Danube River area - Km 347-Km344

NASA Astrophysics Data System (ADS)

Nichersu, Iulian; Mierla, Marian; Trifanov, Cristian

2013-04-01

Cumulative River Dynamic Assessment using Topo-Hydrographical High Definition Surveying in the Danube River area - Km 347-Km344 Iulian NICHERSU, Cristian TRIFANOV, Marian MIERLA The purpose of this paper is to depict and illustrate the benefits of Topo-Hydrographical High Definition Surveying (THHDS), also known as 3D multi-beam scanning, on a topo-hydrological survey application in Danube Valley. This research investigates the evolution of Danube river dynamics. We start with cross-sections made in 2002, 2007 and 2010 in this area and we coupled with 2012 THHDS. 3D multi-beam scanning method of data acquisition improve the spatial hydrological model and offers better dynamics assessment for future studies, considering that this area is carried out dredging works to improve navigation conditions - THHDS technique true modeling capabilities have applications in hydrotechnical works. Dynamics stands out on all 3 axes and cartographic documents have used both the 1930, 1950, and orthophoto images taken during flight to obtain the 3D model of the floodplain through LIDAR method, in 2007.

1D array of dark spot traps formed by counter-propagating nested Gaussian laser beams for trapping and moving atomic qubits

NASA Astrophysics Data System (ADS)

Gillen-Christandl, Katharina; Frazer, Travis D.

2017-04-01

The standing wave of two identical counter-propagating Gaussian laser beams constitutes a 1D array of bright spots that can serve as traps for single neutral atoms for quantum information operations. Detuning the frequency of one of the beams causes the array to start moving, effectively forming a conveyor belt for the qubits. Using a pair of nested Gaussian laser beams with different beam waists, however, forms a standing wave with a 1D array of dark spot traps confined in all dimensions. We have computationally explored the trap properties and limitations of this configuration and, trading off trap depth and frequencies with the number of traps and trap photon scattering rates, we determined the laser powers and beam waists needed for useful 1D arrays of dark spot traps for trapping and transporting atomic qubits in neutral atom quantum computing platforms.

Flatbed-type 3D display systems using integral imaging method

NASA Astrophysics Data System (ADS)

Hirayama, Yuzo; Nagatani, Hiroyuki; Saishu, Tatsuo; Fukushima, Rieko; Taira, Kazuki

2006-10-01

We have developed prototypes of flatbed-type autostereoscopic display systems using one-dimensional integral imaging method. The integral imaging system reproduces light beams similar of those produced by a real object. Our display architecture is suitable for flatbed configurations because it has a large margin for viewing distance and angle and has continuous motion parallax. We have applied our technology to 15.4-inch displays. We realized horizontal resolution of 480 with 12 parallaxes due to adoption of mosaic pixel arrangement of the display panel. It allows viewers to see high quality autostereoscopic images. Viewing the display from angle allows the viewer to experience 3-D images that stand out several centimeters from the surface of the display. Mixed reality of virtual 3-D objects and real objects are also realized on a flatbed display. In seeking reproduction of natural 3-D images on the flatbed display, we developed proprietary software. The fast playback of the CG movie contents and real-time interaction are realized with the aid of a graphics card. Realization of the safety 3-D images to the human beings is very important. Therefore, we have measured the effects on the visual function and evaluated the biological effects. For example, the accommodation and convergence were measured at the same time. The various biological effects are also measured before and after the task of watching 3-D images. We have found that our displays show better results than those to a conventional stereoscopic display. The new technology opens up new areas of application for 3-D displays, including arcade games, e-learning, simulations of buildings and landscapes, and even 3-D menus in restaurants.

Nutritive Value Response of Native Warm-Season Forage Grasses to Harvest Intervals and Durations in Mixed Stands

PubMed Central

Temu, Vitalis W.; Rude, Brian J.; Baldwin, Brian S.

2014-01-01

Interest in management of native warm-season grasses for multiple uses is growing in southeastern USA. Forage quality response of early-succession mixed stands of big bluestem (BB, Andropogon gerardii), indiangrass (IG, Sorghastrum nutans), and little bluestem (SG, Schizachyrium scoparium) to harvest intervals (30-, 40-, 60-, 90 or 120-d) and durations (one or two years) were assessed in crop-field buffers. Over three years, phased harvestings were initiated in May, on sets of randomized plots, ≥90 cm apart, in five replications (blocks) to produce one-, two-, and three-year-old stands, by the third year. Whole-plot regrowths were machine-harvested after collecting species (IG and LB) sample tillers for leafiness estimates. Species-specific leaf area (SLA) and leaf-to-stem ratio (LSR) were greater for early-season harvests and shorter intervals. In a similar pattern, whole-plot crude protein concentrations were greatest for the 30-d (74 g·kg−1 DM) and the least (40 g·kg−1 DM) for the 120-d interval. Corresponding neutral detergent fiber (NDF) values were the lowest (620 g·kg−1 DM) and highest (710 g·kg−1 DM), respectively. In vitro dry matter and NDF digestibility were greater for early-season harvests at shorter intervals (63 and 720 g·kg−1 DM). With strategic harvesting, similar stands may produce quality hay for beef cattle weight gain. PMID:27135504

SETs: stand evaluation tools: I. an individual-tree approach to making stand evaluations

Treesearch

Paul S. DeBald; Joseph J. Mendel

1976-01-01

The authors outline a stand-evaluation method that stresses individuality by (1) making on-the-ground projections of individual tree development; (2) summarizing stand values in terms of the individual trees in the stand and their potential development; and (3) tailoring several management possibilities to an individual stand so the owner can choose among them.

3D printed auto-mixing chip enables rapid smartphone diagnosis of anemia.

PubMed

Plevniak, Kimberly; Campbell, Matthew; Myers, Timothy; Hodges, Abby; He, Mei

2016-09-01

Clinical diagnosis requiring central facilities and site visits can be burdensome for patients in resource-limited or rural areas. Therefore, development of a low-cost test that utilizes smartphone data collection and transmission would beneficially enable disease self-management and point-of-care (POC) diagnosis. In this paper, we introduce a low-cost i POC 3D diagnostic strategy which integrates 3D design and printing of microfluidic POC device with smartphone-based disease diagnosis in one process as a stand-alone system, offering strong adaptability for establishing diagnostic capacity in resource-limited areas and low-income countries. We employ smartphone output (AutoCAD 360 app) and readout (color-scale analytical app written in-house) functionalities for rapid 3D printing of microfluidic auto-mixers and colorimetric detection of blood hemoglobin levels. The auto-mixing of reagents with blood via capillary force has been demonstrated in 1 second without the requirement of external pumps. We employed this i POC 3D system for point-of-care diagnosis of anemia using a training set of patients (n anemia  = 16 and n healthy  = 6), which showed consistent measurements of blood hemoglobin levels (a.u.c. = 0.97) and comparable diagnostic sensitivity and specificity, compared with standard clinical hematology analyzer. Capable of 3D fabrication flexibility and smartphone compatibility, this work presents a novel diagnostic strategy for advancing personalized medicine and mobile healthcare.

A Three-Part Theory of Critical Thinking: Dialogue, Mental Models, and Reliability

DTIC Science & Technology

2000-08-01

A THREE-PART THEORY OF CRITICAL THINKING: DIALOGUE, MENTAL MODELS, AND RELIABILITY1 Marvin S. Cohen, Ph.D. Cognitive Technologies...1. REPORT DATE AUG 2000 2. REPORT TYPE 3. DATES COVERED 00-00-2000 to 00-00-2000 4. TITLE AND SUBTITLE A Three-part Theory of Critical...in logic or decision theory ? Does it require stand-alone courses? How will we persuade students to devote their time to the study of critical

Video File - NASA Conducts Final RS-25 Rocket Engine Test of 2017

NASA Image and Video Library

2017-12-13

NASA engineers at Stennis Space Center capped a year of Space Launch System testing with a final RS-25 rocket engine hot fire on Dec. 13. The 470-second test on the A-1 Test Stand was a “green run” test of an RS-25 flight controller. The engine tested also included a large 3-D-printed part, a pogo accumulator assembly, scheduled for use on future RS-25 flight engines.

Comparison of single and consecutive dual frequency induction surface hardening of gear wheels

NASA Astrophysics Data System (ADS)

Barglik, J.; Ducki, K.; Kukla, D.; Mizera, J.; Mrówka-Nowotnik, G.; Sieniawski, J.; Smalcerz, A.

2018-05-01

Mathematical modelling of single and consecutive dual - frequency induction surface hardening systems are presented and compared. The both models are solved by the 3D FEM-based professional software supported by a number of own numerical procedures. The methodology is illustrated with some examples of surface induction hardening of a gear wheel made of steel 41Cr4. The computations are in a good accordance with experiments provided on the laboratory stand.

Automatic determination of trunk diameter, crown base and height of scots pine (Pinus Sylvestris L.) Based on analysis of 3D point clouds gathered from multi-station terrestrial laser scanning. (Polish Title: Automatyczne okreslanie srednicy pnia, podstawy korony oraz wysokosci sosny zwyczajnej (Pinus Silvestris L.) Na podstawie analiz chmur punktow 3D pochodzacych z wielostanowiskowego naziemnego skanowania laserowego)

NASA Astrophysics Data System (ADS)

Ratajczak, M.; Wężyk, P.

2015-12-01

Rapid development of terrestrial laser scanning (TLS) in recent years resulted in its recognition and implementation in many industries, including forestry and nature conservation. The use of the 3D TLS point clouds in the process of inventory of trees and stands, as well as in the determination of their biometric features (trunk diameter, tree height, crown base, number of trunk shapes), trees and lumber size (volume of trees) is slowly becoming a practice. In addition to the measurement precision, the primary added value of TLS is the ability to automate the processing of the clouds of points 3D in the direction of the extraction of selected features of trees and stands. The paper presents the original software (GNOM) for the automatic measurement of selected features of trees, based on the cloud of points obtained by the ground laser scanner FARO. With the developed algorithms (GNOM), the location of tree trunks on the circular research surface was specified and the measurement was performed; the measurement covered the DBH (l: 1.3m), further diameters of tree trunks at different heights of the tree trunk, base of the tree crown and volume of the tree trunk (the selection measurement method), as well as the tree crown. Research works were performed in the territory of the Niepolomice Forest in an unmixed pine stand (Pinussylvestris L.) on the circular surface with a radius of 18 m, within which there were 16 pine trees (14 of them were cut down). It was characterized by a two-storey and even-aged construction (147 years old) and was devoid of undergrowth. Ground scanning was performed just before harvesting. The DBH of 16 pine trees was specified in a fully automatic way, using the algorithm GNOM with an accuracy of +2.1%, as compared to the reference measurement by the DBH measurement device. The medium, absolute measurement error in the cloud of points - using semi-automatic methods "PIXEL" (between points) and PIPE (fitting the cylinder) in the FARO Scene 5.x., showed the error, 3.5% and 5.0%,.respectively The reference height was assumed as the measurement performed by the tape on the cut tree. The average error of automatic determination of the tree height by the algorithm GNOM based on the TLS point clouds amounted to 6.3% and was slightly higher than when using the manual method of measurements on profiles in the TerraScan (Terrasolid; the error of 5.6%). The relatively high value of the error may be mainly related to the small number of points TLS in the upper parts of crowns. The crown height measurement showed the error of +9.5%. The reference in this case was the tape measurement performed already on the trunks of cut pine trees. Processing the clouds of points by the algorithms GNOM for 16 analyzed trees took no longer than 10 min. (37 sec. /tree). The paper mainly showed the TLS measurement innovation and its high precision in acquiring biometric data in forestry, and at the same time also the further need to increase the degree of automation of processing the clouds of points 3D from terrestrial laser scanning.

In Situ Growth of Free-Standing All Metal Oxide Asymmetric Supercapacitor.

PubMed

Yin, Bo-Si; Wang, Zhen-Bo; Zhang, Si-Wen; Liu, Chang; Ren, Qing-Qing; Ke, Ke

2016-10-05

Metal oxides have attracted renewed interest in applications as energy storage and conversion devices. Here, a new design is reported to acquire an asymmetric supercapacitor assembled by all free-standing metal oxides. The positive electrode is made of 3D NiO open porous nanoribbons network on nickel foam and the negative electrode is composed of SnO 2 /MnO 2 nanoflakes grown on carbon cloth (CC) substrate. The combination of two metal oxide electrodes which replaced the traditional group of carbon materials together with metal oxide has achieved a higher energy density. The self-supported 3D NiO nanoribbons network demonstrates a high specific capacitance and better cycle performance without obvious mechanical deformation despite of undergoing harsh bulk redox reactions. The SnO 2 /MnO 2 nanoflakes as the pseudocapacitive electrode exhibit a wide range of voltage window (-1 to 1 V), which is conducive to electrochemical energy storage. The (CC/SnO 2 /MnO 2 )(-)//(NiO/Ni foam)(+) asymmetric supercapacitor device delivers an energy density of 64.4 Wh kg -1 (at a power density of 250 W kg -1 ) and two devices in series are applied to light up 24 red LEDs for about 60 s. The outstanding electrochemical properties of the device hold great promise for long-life, high-energy, and high-power energy storage/conversion applications.

3D Bioprinting of Self-Standing Silk-Based Bioink.

PubMed

Zheng, Zhaozhu; Wu, Jianbing; Liu, Meng; Wang, Heng; Li, Chunmei; Rodriguez, María J; Li, Gang; Wang, Xiaoqin; Kaplan, David L

2018-03-01

Silk/polyethylene glycol (PEG) hydrogels are studied as self-standing bioinks for 3D printing for tissue engineering. The two components of the bioink, silk fibroin protein (silk) and PEG, are both Food and Drug Administration approved materials in drug and medical device products. Mixing PEG with silk induces silk β-sheet structure formation and thus gelation and water insolubility due to physical crosslinking. A variety of constructs with high resolution, high shape fidelity, and homogeneous gel matrices are printed. When human bone marrow mesenchymal stem cells are premixed with the silk solution prior to printing and the constructs are cultured in this medium, the cell-loaded constructs maintain their shape over at least 12 weeks. Interestingly, the cells grow faster in the higher silk concentration (10%, w/v) gel than in lower ones (7.5 and 5%, w/v), likely due to the difference in material stiffness and the amount of residual PEG remaining in the gel related to material hydrophobicity. Subcutaneous implantation of 7.5% (w/v) bioink gels with and without printed fibroblast cells in mice reveals that the cells survive and proliferate in the gel matrix for at least 6 week postimplantation. The results suggest that these silk/PEG bioink gels may provide suitable scaffold environments for cell printing and function. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Carbon balance and productivity of Lemna gibba, a candidate plant for CELSS.

PubMed

Gale, J; Smernoff, D T; Macler, B A; MacElroy, R D

1989-01-01

The photosynthesis and productivity of Lemna gibba were studied with a view to its use in Controlled Ecological Life Support Systems (CELSS). Photosynthesis of L. gibba floating on the nutrient solution could be driven by light coming from either above or below. Light from below was about 75% as effective as from above when the stand was sparse, but much less so with dense stands. High rates of photosynthesis (ca. 800 nanomoles CO2 g dry weight (DW)-1 s-1) were measured at 750 micromoles m-2 s-1 PPF and 1500 micromoles mol-1 CO2. This was attained at densities up to 660 g fresh weight (FW) m-2 with young cultures. After a few days growth under these conditions, and at higher densities, the rate of photosynthesis dropped to less than 25% of the initial value. This drop was only partly alleviated by thinning the stand or by introducing a short dark period at high temperature (26 degrees C). Despite the drop in the rate of photosynthesis, maximum yields were obtained in batch cultures grown under continuous light, constant temperature and high [CO2]. Plant protein content was less than reported for field grown Lemna. When the plants were harvested daily, maintaining a stand density of 600 g FW m-2, yields of 18 g DW m-2 d-1 were obtained. The total dry weight of L. gibba included 40% soluble material (sugars and amino acids), 15% protein, 5% starch, 5% ash and 35% cellulose and other polymers. We conclude that a CELSS system could be designed around stacked, alternate layers of transparent Lemna trays and lamps. This would allow for 7 tiers per meter height. Based on present data from single layers, the yield of such a system is calculated to be 135 g DW m-3 d-1 of a 100% edible, protein-rich food.

Mechanistic insights of the Min oscillator via cell-free reconstitution and imaging

NASA Astrophysics Data System (ADS)

Mizuuchi, Kiyoshi; Vecchiarelli, Anthony G.

2018-05-01

The MinD and MinE proteins of Escherichia coli self-organize into a standing-wave oscillator on the membrane to help align division at mid-cell. When unleashed from cellular confines, MinD and MinE form a spectrum of patterns on artificial bilayers—static amoebas, traveling waves, traveling mushrooms, and bursts with standing-wave dynamics. We recently focused our cell-free studies on bursts because their dynamics recapitulate many features of Min oscillation observed in vivo. The data unveiled a patterning mechanism largely governed by MinE regulation of MinD interaction with membrane. We proposed that the MinD to MinE ratio on the membrane acts as a toggle switch between MinE-stimulated recruitment and release of MinD from the membrane. In this review, we summarize cell-free data on the Min system and expand upon a molecular mechanism that provides a biochemical explanation as to how these two ‘simple’ proteins can form the remarkable spectrum of patterns.

Detection of dead standing Eucalyptus camaldulensis without tree delineation for managing biodiversity in native Australian forest

NASA Astrophysics Data System (ADS)

Miltiadou, Milto; Campbell, Neil D. F.; Gonzalez Aracil, Susana; Brown, Tony; Grant, Michael G.

2018-05-01

In Australia, many birds and arboreal animals use hollows for shelters, but studies predict shortage of hollows in near future. Aged dead trees are more likely to contain hollows and therefore automated detection of them plays a substantial role in preserving biodiversity and consequently maintaining a resilient ecosystem. For this purpose full-waveform LiDAR data were acquired from a native Eucalypt forest in Southern Australia. The structure of the forest significantly varies in terms of tree density, age and height. Additionally, Eucalyptus camaldulensis have multiple trunk splits making tree delineation very challenging. For that reason, this paper investigates automated detection of dead standing Eucalyptus camaldulensis without tree delineation. It also presents the new feature of the open source software DASOS, which extracts features for 3D object detection in voxelised FW LiDAR. A random forest classifier, a weighted-distance KNN algorithm and a seed growth algorithm are used to create a 2D probabilistic field and to then predict potential positions of dead trees. It is shown that tree health assessment is possible without tree delineation but since it is a new research directions there are many improvements to be made.

TMS delivered for A-3 Test Stand

NASA Image and Video Library

2010-03-17

A state-of-the-art thrust measurement system for the A-3 Test Stand under construction at NASA's John C. Stennis Space Center was delivered March 17. Once completed, the A-3 stand (seen in background) will allow simulated high-altitude testing on the next generation of rocket engines for America's space program. Work on the stand began in 2007, with activation scheduled for 2012. The stand is the first major test structure to be built at Stennis since the 1960s. The recently delivered TMS was fabricated by Thrust Measurement Systems in Illinois. It is an advanced calibration system capable of measuring vertical and horizontal thrust loads with an accuracy within 0.15 percent at 225,000 pounds.

3. EAST SIDE, ALSO SHOWING COVERED TANKS AND TEST STAND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. EAST SIDE, ALSO SHOWING COVERED TANKS AND TEST STAND 1-5 AT RIGHT. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-4, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Isopropyl alcohol tank installed at A-3 Test Stand

NASA Technical Reports Server (NTRS)

2009-01-01

An isopropyl alcohol (IPA) tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen IPA, water and liquid oxygen (LOX) tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

Water tank installed at A-3 Test Stand

NASA Technical Reports Server (NTRS)

2009-01-01

A water tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen water, liquid oxygen (LOX) and isopropyl alcohol (IPA) tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

Liquid oxygen tank installed at A-3 Test Stand

NASA Technical Reports Server (NTRS)

2009-01-01

A liquid oxygen (LOX) tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen LOX, isopropyl alcohol (IPA) and water tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

Water tank installed at A-3 Test Stand

NASA Image and Video Library

2009-08-13

A water tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen water, liquid oxygen (LOX) and isopropyl alcohol (IPA) tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

Liquid oxygen tank installed at A-3 Test Stand

NASA Image and Video Library

2009-09-18

A liquid oxygen (LOX) tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen LOX, isopropyl alcohol (IPA) and water tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

Isopropyl alcohol tank installed at A-3 Test Stand

NASA Image and Video Library

2009-09-18

An isopropyl alcohol (IPA) tank is lifted into place at the A-3 Test Stand being built at NASA's John C. Stennis Space Center. Fourteen IPA, water and liquid oxygen (LOX) tanks are being installed to support the chemical steam generators to be used on the A-3 Test Stand. The IPA and LOX tanks will provide fuel for the generators. The water will allow the generators to produce steam that will be used to reduce pressure inside the stand's test cell diffuser, enabling operators to simulate altitudes up to 100,000 feet. In that way, operators can perform the tests needed on rocket engines being built to carry humans back to the moon and possibly beyond. The A-3 Test Stand is set for completion and activation in 2011.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miao, Jianwei; Ercius, Peter; Billinge, S. J. L.

Crystallography has been fundamental to the development of many fields of science over the last century. However, much of our modern science and technology relies on materials with defects and disorders, and their three-dimensional (3D) atomic structures are not accessible to crystallography. One method capable of addressing this major challenge is atomic electron tomography. By combining advanced electron microscopes and detectors with powerful data analysis and tomographic reconstruction algorithms, it is now possible to determine the 3D atomic structure of crystal defects such as grain boundaries, stacking faults, dislocations, and point defects, as well as to precisely localize the 3Dmore » coordinates of individual atoms in materials without assuming crystallinity. In this work, we review the recent advances and the interdisciplinary science enabled by this methodology. We also outline further research needed for atomic electron tomography to address long-standing unresolved problems in the physical sciences.« less

A Short Course in Post-Structuralism.

ERIC Educational Resources Information Center

Tompkins, Jane

1988-01-01

Asserts that post-structuralism cannot be applied to literary texts because to talk about applying post-structuralism assumes: (1) free-standing subjects; (2) free-standing objects of investigation; (3) free-standing methods; and (4) free-standing interpretation. (RAE)

Stand Structure and Composition 32 Years after Precommercial Thinning Treatments in a Mixed Northern Conifer Stand in Central Maine

Treesearch

Aaron R. Weiskittel; Laura S. Kenefic; Rongxia Li; John Brissette

2011-01-01

The effects of four precommercial thinning (PCT) treatments on an even-aged northern conifer stand in Maine were investigated by examining stand structure and composition 32 years after treatment. Replicated treatments applied in 1976 included: (1) control (no PCT), (2) row thinning (rowthin; 5-ft-wide row removal with 3-ft-wide residual strips), (3) row thinning with...

Canopy transpiration for two Japanese cypress forests with contrasting structures

NASA Astrophysics Data System (ADS)

Tsuruta, K.; Komatsu, H.; Kume, T.; Shinohara, Y.; Otsuki, K.

2012-12-01

Canopy transpiration (EC) could have large variations among stands with different structures. To evaluate a difference in EC between stands with different structures for Japanese cypress, we observed EC using the sap flow technique in two stands with contrasting structures (age was 19 year and 99 year, mean diameter at breast height was 13.5 cm and 44.6 cm, stem density was 2100 trees ha-1 and 350 trees ha-1, respectively) for 5 months under the same meteorological condition. The mean stand sap flux density (JS) for measurement period and stand sapwood area (AS_stand) for the old stand (0.43 m3 m-2 day-1 and 15.2 m2 ha-1) were lower than those for the young stand (0.62 m3 m-2 day-1 and 20.4 m2 ha-1) by 31.1 % and 25.4 %, respectively. EC is calculated as a product of JS and AS_stand. Therefore the EC in the old stand was lower than that in the young stand by 50 %. We calculated the contribution of the reference JS for a given meteorological conditions (JSref) and the response of JS to the meteorological conditions (JSresp) in the two stands, and examined which is a primary factor for the difference of EC between the two studied stands. The JSresp for the young stand were not considerably different from that for the old stand, whereas JSref for the young stand was greater than that for the old stand. This indicates that JSref (not JSresp) was the primary cause for the difference of EC between the two stands. Further studies observing EC from stands with various structures are needed to generalize our conclusions.

Insulating Ferromagnetic LaCoO3-δ Films: A Phase Induced by Ordering of Oxygen Vacancies

NASA Astrophysics Data System (ADS)

Biškup, Neven; Salafranca, Juan; Mehta, Virat; Oxley, Mark P.; Suzuki, Yuri; Pennycook, Stephen J.; Pantelides, Sokrates T.; Varela, Maria

2014-02-01

The origin of ferromagnetism in strained epitaxial LaCoO3 films has been a long-standing mystery. Here, we combine atomically resolved Z-contrast imaging, electron-energy-loss spectroscopy, and density-functional calculations to demonstrate that, in epitaxial LaCoO3 films, oxygen-vacancy superstructures release strain, control the film's electronic properties, and produce the observed ferromagnetism via the excess electrons in the Co d states. Although oxygen vacancies typically dope a material n-type, we find that ordered vacancies induce Peierls-like minigaps which, combined with strain relaxation, trigger a nonlinear rupture of the energy bands, resulting in insulating behavior.

The construction of 3D-engineered tissues composed of cells and extracellular matrices by hydrogel template approach.

PubMed

Matsusaki, Michiya; Yoshida, Hiroaki; Akashi, Mitsuru

2007-06-01

The three-dimensional (3D)-engineered tissues composed of only cells and extracellular matrices (ECM) were constructed by the hydrogel template approach. The disulfide-crosslinked poly(gamma-glutamic acid) hydrogels were prepared as a template hydrogel. These template hydrogels were easily decomposed under physiological conditions using reductants such as cysteine, glutathione and dithiothreitol by cleavage of disulfide crosslinkage to thiol groups. The decomposed polymers are soluble in cell culture medium. The cleaving of disulfide bond was determined by UV-vis and FT-IR spectroscopies. We successfully prepared the 3D-engineered tissues (thickness/diameter, 2mm/1cm) composed of mouse L929 fibroblast cells and ECM by the decomposition of only the template hydrogel with cysteine after 10 days 3D-cell culture on/in the template hydrogel. The size and thickness of the 3D-engineered tissues was completely transferred from the template hydrogel. The cultured L929 cells viability in the obtained engineered tissues was confirmed by a culture test, WST-1 method and LIVE/DEAD staining assay. The engineered tissue was self-standing and highly dense composite of the cultured cells and collagen produced by the cells. This hydrogel template approach may be useful as a new class of soft-tissue engineering technology to substitute a synthetic polymer scaffold to the ECM scaffold produced from the cultured cells.

Relatedness of the O-polysaccharide structures of Escherichia coli O123 and Salmonella enterica O58, both containing 4,6-dideoxy-4-{N-[(S)-3-hydroxybutanoyl]-D-alanyl}amino-D-glucose; revision of the E. coli O123 O-polysaccharide structure.

PubMed

Perepelov, Andrei V; Liu, Bin; Shevelev, Sergei D; Senchenkova, Sof'ya N; Shashkov, Alexander S; Feng, Lu; Knirel, Yuriy A; Wang, Lei

2010-04-19

O-Polysaccharides were isolated by mild acid degradation of the lipopolysaccharides of Escherichia coli O123 and Salmonella enterica O58 and studied by chemical methods and 2D (1)H and (13)C NMR spectroscopy, including experiments in a H(2)O/D(2)O mixture, which enabled observation of correlations for nitrogen-linked protons. The following structure of the O-polysaccharide of E. coli O123 was established: -->3)-beta-D-Quip4NAlaHb-(1-->6)-alpha-D-GlcpNAc-(1-->3)-alpha-L-QuipNAc-(1-->3)-alpha-D-Glcp (6)(approx. 30% OAc)NAc-(1--> where L-QuipNAc stands for 2-acetamido-2,6-dideoxy-L-glucose and D-Qui4NAlaHb for 4-{N-[(S)-3-hydroxybutanoyl]-D-alanyl}amino-4,6-dideoxy-D-glucose. The latter was isolated as an ethylene glycol glycoside by three sequential Smith degradations of the O-deacetylated O-polysaccharide. The structure established in this work is at variance with the E. coli O123-polysaccharide structure reported earlier [Clark, C. G.; Kropinski, A. M.; Parolis, H.; Grant, C. C.; Trout-Yakel, K. M.; Franklin, K.; Ng, L. K.; Paramonov, N. A.; Parolis, L. A.; Rahn, K.; Tabor, H. J. Med. Microbiol.2009, 58, 884-894]. In accordance with the genetic data, the O-polysaccharide of S. enterica O58 has the same structure, except for it lacks the O-acetylation. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

CSG delivery and installation

NASA Image and Video Library

2010-10-27

The first of nine chemical steam generator (CSG) units that will be used on the A-3 Test Stand is prepared for installation Oct. 24, 2010, at John C. Stennis Space Center. The unit was installed at the E-2 Test Stand for verification and validation testing before it is moved to the A-3 stand. Steam generated by the nine CSG units that will be installed on the A-3 stand will create a vacuum that allows Stennis operators to test next-generation rocket engines at simulated altitudes up to 100,000 feet.

CSG delivery and installation

NASA Image and Video Library

2010-10-22

The first of nine chemical steam generator (CSG) units that will be used on the A-3 Test Stand arrived at John. C. Stennis Space Center on Oct. 22, 2010. The unit was installed at the E-2 Test Stand for verification and validation testing before it is moved to the A-3 stand. Steam generated by the nine CSG units that will be installed on the A-3 stand will create a vacuum that allows Stennis operators to test next-generation rocket engines at simulated altitudes up to 100,000 feet.

Radiometric Correction of Multitemporal Hyperspectral Uas Image Mosaics of Seedling Stands

NASA Astrophysics Data System (ADS)

Markelin, L.; Honkavaara, E.; Näsi, R.; Viljanen, N.; Rosnell, T.; Hakala, T.; Vastaranta, M.; Koivisto, T.; Holopainen, M.

2017-10-01

Novel miniaturized multi- and hyperspectral imaging sensors on board of unmanned aerial vehicles have recently shown great potential in various environmental monitoring and measuring tasks such as precision agriculture and forest management. These systems can be used to collect dense 3D point clouds and spectral information over small areas such as single forest stands or sample plots. Accurate radiometric processing and atmospheric correction is required when data sets from different dates and sensors, collected in varying illumination conditions, are combined. Performance of novel radiometric block adjustment method, developed at Finnish Geospatial Research Institute, is evaluated with multitemporal hyperspectral data set of seedling stands collected during spring and summer 2016. Illumination conditions during campaigns varied from bright to overcast. We use two different methods to produce homogenous image mosaics and hyperspectral point clouds: image-wise relative correction and image-wise relative correction with BRDF. Radiometric datasets are converted to reflectance using reference panels and changes in reflectance spectra is analysed. Tested methods improved image mosaic homogeneity by 5 % to 25 %. Results show that the evaluated method can produce consistent reflectance mosaics and reflectance spectra shape between different areas and dates.

Acute alcohol intoxication impairs segmental body alignment in upright standing.

PubMed

Hafstrom, A; Patel, M; Modig, F; Magnusson, M; Fransson, P A

2014-01-01

Balance control when standing upright is a complex process requiring input from several partly independent mechanisms such as coordination, feedback and feedforward control, and adaptation. Acute alcohol intoxication from ethanol is recognized as a major contributor to accidental falls requiring medical care. This study aimed to investigate if intoxication at 0.06 and 0.10% blood alcohol concentration affected body alignment. Mean angular positions of the head, shoulder, hip, and knee were measured with 3D-motion analysis and compared with the ankle position in 25 healthy adults during standing with or without perturbations, and with eyes open or closed. Alcohol intoxication had significant effects on body alignment during perturbed and unperturbed stance, and on adaptation to perturbations. It induced a significantly more posterior alignment of the knees and shoulders, and a tendency for a more posterior and left deviated head alignment in perturbed stance than when sober. The impact of alcohol intoxication was most apparent on the knee alignment, where availability of visual information deteriorated the adaptation to perturbations. Thus, acute alcohol intoxication resulted in inadequate balance control strategies with increased postural rigidity and impaired adaptation to perturbations. These factors probably contribute to the increased risk of falling when intoxicated with alcohol.

Growing season burns for control of hardwoods in longleaf pine stands

Treesearch

William D. Boyer

1990-01-01

Summer fires in existing longleaf pine stands carry undue risk of pine mortality. One summer fire caused as much mortality among pines in the l- through 4-inch d.b.h. classes as two successive summer fires among hardwoods of the same size. Mortality among mature pines was also excessive. Hardwood top-kill following a spring fire seemed affected more by fire intensity...

Effects of Gender, Load, and Backpack on Easy Standing and Vertical Jump Performance. Volume 2

DTIC Science & Technology

1982-03-01

D BY RICHARD C. NELSON AND PHILIP E. MARTIN BIOMECHANICS LABORATORY THE PENNSYLVANIA STATE UNIVERSITY UNIVERSITY PARK, PENNSYLVANIA MARCH...PERFORMING ORGANIZATION NAME AND ADDRESS Biomechanics Laboratory The Pennsylvania State University University Park. Pennsylvania 16802 10. PROGRAM...REFERENCES APPENDICES A. Clothing and Equipment Used in This Study B. ANOVA Summary Tables for Easy Standing C. ANOVA Summary Tables for

Sex Pheromone of Conophthorus ponderosae (Coleoptera: Scolytidae) in a Coastal Stand of Western White Pine (Pinaceae)

Treesearch

Daniel R. Miller; Harold D. Pierce; Peter de Groot; Nicole Jeans-Williams; Robb Bennett; John H. Borden

2000-01-01

An isolated stand of western white pine, Pinus monticola Dougl. ex D. Don, on Texada Island (49°40'N, 124°10'W), British Columbia, is extremely valuable as a seed-production area for progeny resistant to white pine blister rust, Cronartium ribicola J.C. Fisch. (Cronartiaceae). During the past 5 years, cone beetles, ...

Reward and Visual Feedback Relative to the Performance and Mechanical Efficiency of High School Girls in the Standing Broad Jump.

ERIC Educational Resources Information Center

Zebas, Carole J.

This study focuses on changes occurring in selected mechanical components of high school girls performing the standing broad jump, and collects data pertaining to the effects of monetary reward and videotape feedback upon the following components: (a) distance jumped, (b) maximum angle of knee flexion, (c) maximum angle of hip flexion, (d) hip…

Small Arms Handbook WS - 1

DTIC Science & Technology

1966-01-01

1) Unsupported Position (without use of bipod). (a) Squatting . (b) Kneeling. (c) Kneeling Supported.J (d) Standing. (e) Sling Supported H-ip. Z6 (Z...situations of this nature, the automatic rifle should-be employed In the semiautomatic role from the squatting , kneeling or standing positions as...Unaupported firing positions. (Without Use of the bipod.) (1) Squatting position. The sqtatting position is a relatively stable position which can be assumed

Relation of Crown Width to Tree Diameter In Some Upland Hardwood Stands of Southern Illinois

Treesearch

Leon S. Minckler; Samuel F. Gingrich

1970-01-01

Crown width-d.b.h. relationships in well stocked, uneven-aged stands of oak and hickory were similar to those for open-grown trees and were independent of site, crown class, and species. The irregular crowns of forest grown trees interface and overlap, however, and measuring crown extensions to the branch tips tended to overestimate effective crown area

EAG response and behavioral orientation of Dastarcus helophoroides (Fairmaire) (Coleoptera: Bothrideridae) to synthetic host-associated volatiles

PubMed Central

Schütz, Stefan

2017-01-01

Dastarcus helophoroides Fairmaire (Coleoptera: Bothrideridae) is an effective predatory beetle of larvae and pupae of several cerambycid beetles including Monochamus alternatus and Anoplophora glabripennis. Electroantennography (EAG) and a dynamic two-choice olfactometer were respectively used to measure the antennal and behavioral responses of both sexes to selected volatile compounds. Female and male D. helophoroides exhibited similar EAG and behavioral responses. Significant dose-dependent EAG responses in both sexes were elicited by nonanal, octanal, cis-3-hexenol, 3-carene, (R)-(+)-α-pinene, (S)-(-)-α-pinene, (R)-(+)-limonene and (S)-(-)-limonene. Female and male beetles were repelled at high concentration by cis-3-hexenol and (S)-(-)-limonene, respectively. Both sexes of D. helophoroides were significantly attracted to nonanal, cis-3-hexenol, 3-carene and (R)-(+)-limonene even at low concentrations. These compounds might be used either individually or in mixtures for developing biological control methods to attract this predatory beetle into forest stands threatened by cerambycid beetles. PMID:29267391

Streaming and particle motion in acoustically-actuated leaky systems

NASA Astrophysics Data System (ADS)

Nama, Nitesh; Barnkob, Rune; Jun Huang, Tony; Kahler, Christian; Costanzo, Francesco

2017-11-01

The integration of acoustics with microfluidics has shown great promise for applications within biology, chemistry, and medicine. A commonly employed system to achieve this integration consists of a fluid-filled, polymer-walled microchannel that is acoustically actuated via standing surface acoustic waves. However, despite significant experimental advancements, the precise physical understanding of such systems remains a work in progress. In this work, we investigate the nature of acoustic fields that are setup inside the microchannel as well as the fundamental driving mechanism governing the fluid and particle motion in these systems. We provide an experimental benchmark using state-of-art 3D measurements of fluid and particle motion and present a Lagrangian velocity based temporal multiscale numerical framework to explain the experimental observations. Following verification and validation, we employ our numerical model to reveal the presence of a pseudo-standing acoustic wave that drives the acoustic streaming and particle motion in these systems.

Astronaut Edgar D. Mitchell, Apollo 14 Lunar Module pilot

NASA Technical Reports Server (NTRS)

1970-01-01

Portrait of Astronaut Edgar D. Mitchell, Apollo 14 lunar landing mission Lunar Module pilot in civilian clothes. Left to right, are Astronauts Edgar D. Mitchell, lunar module pilot; Stuart A. Roosa, command module pilot; and Alan B. Shepard Jr., commander. They are standing by a Command Module Trainer which was used in the exercise.

Reconstructing the spatial pattern of trees from routine stand examination measurements

USGS Publications Warehouse

Hanus, M.L.; Hann, D.W.; Marshall, D.D.

1998-01-01

Reconstruction of the spatial pattern of trees is important for the accurate visual display of unmapped stands. The proposed process for generating the spatial pattern is a nonsimple sequential inhibition process, with the inhibition zone proportionate to the scaled maximum crown width of an open-grown tree of the same species and same diameter at breast height as the subject tree. The results of this coordinate generation procedure are compared with mapped stem data from nine natural stands of Douglas-fir at two ages by the use of a transformed Ripley's K(d) function. The results of this comparison indicate that the proposed method, based on complete tree lists, successfully replicated the spatial patterns of the trees in all nine stands at both ages and over the range of distances examined. On the basis of these findings and the procedure's ability to model effects through time, the nonsimple sequential inhibition process has been chosen to generate tree coordinates in the VIZ4ST computer program for displaying forest stand structure in naturally regenerated young Douglas-fir stands. For. Sci.

Lower cognitive performance among long-term type 1 diabetes survivors: A case-control study.

PubMed

Awad, Anna; Lundqvist, Robert; Rolandsson, Olov; Sundström, Anna; Eliasson, Mats

2017-08-01

Patients with type 1 diabetes (T1D) have an increased risk of cognitive dysfunction. The cognitive decrement is believed to depend on macro- and microvascular complications and long disease duration. Some patients do not develop these complications, but still report cognitive symptoms. We examined if long-standing T1D without complications is associated with lower cognitive performance. A group of patients (n=43) with long-standing T1D (>30years) without micro- or macro vascular complications was compared with a non-diabetic control group (n=86) on six cognitive tests which probed episodic memory, semantic memory, episodic short-term memory, visual attention and psychomotor speed. Each patient was matched with two controls regarding age, gender and education. A linear mixed effect model was used to analyze the data. The mean age was 57years and mean duration was 41years. Patients with diabetes had lower diastolic blood pressure but BMI, waist circumference, systolic blood pressure and smoking did not differ between groups. Patients had lower results than non-diabetic controls in episodic short-term memory (p<0.001) and also lower values on a test that mirrors visual attention and psychomotor speed (p=0.019). Long-standing T1D was associated with lower cognitive performance, regardless of other diabetes-related complications. Copyright © 2017 Elsevier Inc. All rights reserved.

Sagittal Thoracic and Lumbar Spine Profiles in Upright Standing and Lying Prone Positions Among Healthy Subjects: Influence of Various Biometric Features.

PubMed

Salem, Walid; Coomans, Ysaline; Brismée, Jean-Michel; Klein, Paul; Sobczak, Stéphane; Dugailly, Pierre-Michel

2015-08-01

A prospective study was performed on the assessment of both thoracic and lumbar spine sagittal profiles (from C7 to S1). To propose a new noninvasive method for measuring the spine curvatures in standing and lying prone positions and to analyze their relationship with various biometric characteristics. Modifications of spine curvatures (i.e. lordosis or kyphosis) are of importance in the development of spinal disorders. Studies have emphasized the development of new devices to measure the spine sagittal profiles using a noninvasive and low-cost method. To date, it has not been applied for analyzing both lumbar and thoracic alterations for various positioning. Seventy-five healthy subjects (mean 22.6 ± 4.3 yr) were recruited to participate in this study. Thoracic and lumbar sagittal profiles were assessed in standing and lying prone positions using a 3D digitizer. In addition, several biometric data were collected including maximal trunk isometric strength for flexion and extension movement. Statistical analysis consisted in data comparisons of spine profiles and a multivariate analysis including biometric features, to classify individuals considering low within- and high between-variability. Kyphosis and lordosis angles decreased significantly from standing to lying prone position by an average of 13.4° and 16.6°, respectively. Multivariate analysis showed a sample clustering of 3 homogenous subgroups. The first group displayed larger lordosis and flexibility, and had low data values for height, weight, and strength. The second group had lower values than the overall trend of the whole sample, whereas the third group had larger score values for the torques, height, weight, waist, body mass index, and kyphosis angle but a reduced flexibility. The present results demonstrate a significant effect of the positioning on both thoracic and lumbar spine sagittal profiles and highlight the use of cluster analysis to categorize subgroups after biometric characteristics including curvature measurement. N/A.

3. BUILDING 8767, NORTH REAR AND WEST SIDE, TEST STAND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. BUILDING 8767, NORTH REAR AND WEST SIDE, TEST STAND 1-A AT FAR RIGHT. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Observation Bunkers for Test Stand 1-A, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Validation of Cardiovascular Parameters During NASA's Functional Task Test

NASA Technical Reports Server (NTRS)

Arzeno, N. M.; Stenger, M. B.; Bloomberg, J. J.; Platts, Steven H.

2008-01-01

Microgravity-induced physiological changes, including cardiovascular deconditioning may impair crewmembers f capabilities during exploration missions on the Moon and Mars. The Functional Task Test (FTT), which will be used to assess task performance in short and long duration astronauts, consists of 7 functional tests to evaluate crewmembers f ability to perform activities to be conducted in a partial-gravity environment or following an emergency landing on Earth. The Recovery from Fall/Stand Test (RFST) tests both the subject fs ability to get up from a prone position and orthostatic intolerance. PURPOSE: Crewmembers have never become presyncopal in the first 3 min of quiet stand, yet it is unknown whether 3 min is long enough to cause similar heart rate fluctuations to a 5-min stand. The purpose of this study was to validate and test the reliability of heart rate variability (HRV) analysis of a 3-min quiet stand. METHODS: To determine the validity of using 3 vs. 5-min of standing to assess HRV, 7 healthy subjects remained in a prone position for 2 min, stood up quickly and stood quietly for 6 min. ECG and continuous blood pressure data were recorded. Mean R-R interval and spectral HRV were measured in minutes 0-3 and 0-5 following the heart rate transient due to standing. Significant differences between the segments were determined by a paired t-test. To determine the reliability of the 3-min stand test, 13 healthy subjects completed 3 trials of the complete FTT on separate days, including the RFST with a 3-min stand test. Analysis of variance (ANOVA) was performed on the HRV measures. RESULTS: Spectral HRV measures reflecting autonomic activity were not different (p>0.05) during the 0-3 and 0-5 min segment (mean R-R interval: 738+/-74 ms, 728+/-69 ms; low frequency to high frequency ratio: 6.5+/-2.2, 7.7+/-2.7; normalized high frequency: 0.19+/-0.03, 0.18+/-0.04). The average coefficient of variation for mean R-R interval, systolic and diastolic blood pressures in the prone position and stand test were less than 8% for the test sessions. ANOVA results yielded a greater inter-subject variability (p.0.006) than inter-session variability (p>0.05) for HRV in the stand test. CONCLUSION: These studies show that a 3 minute stand delivers repeatable cardiovascular heart rate and BP data in the context of this larger series of tests such as the FTT.

STS-92 crew takes part in a Leak Seal Kit Fit Check in the SSPF

NASA Technical Reports Server (NTRS)

1999-01-01

STS-92 crew members discuss results of a Leak Seal Kit Fit Check on the Pressurized Mating Adapter -3, part of their mission payload, with JSC and Boeing representatives. From left are Mission Specialists Michael E. Lopez-Alegria; Koichi Wakata, who represents the National Space Development Agency of Japan (NASDA); (standing) Peter J.K. 'Jeff' Wisoff (Ph.D.) and William Surles 'Bill' McArthur Jr.; (seated) Pilot Pamela A. Melroy; Dave Moore (behind Melroy), with Boeing; Mission Specialist Leroy Chiao (Ph.D.); Brian Warkentine, with JSC; and Commander Brian Duffy. The mission payload also includes an integrated truss structure (Z-1 truss). Launch of STS-92 is scheduled for Feb. 24, 2000.

Culturing of avian embryos for time-lapse imaging.

PubMed

Rupp, Paul A; Rongish, Brenda J; Czirok, Andras; Little, Charles D

2003-02-01

Monitoring morphogenetic processes, at high resolution over time, has been a long-standing goal of many developmental cell biologists. It is critical to image cells in their natural environment whenever possible; however, imaging many warm-blooded vertebrates, especially mammals, is problematic. At early stages of development, birds are ideal for imaging, since the avian body plan is very similar to that of mammals. We have devised a culturing technique that allows for the acquisition of high-resolution differential interference contrast and epifluorescence images of developing avian embryos in a 4-D (3-D + time) system. The resulting information, from intact embryos, is derived from an area encompassing several millimeters, at micrometer resolution for up to 30 h.

Effect of sacroiliac manipulation on postural sway in quiet standing: a randomized controlled trial.

PubMed

Farazdaghi, Mohammad Reza; Motealleh, Alireza; Abtahi, Forough; Panjan, Andrej; Šarabon, Nejc; Ghaffarinejad, Farahnaz

Sacroiliac joint manipulation can alter joint and muscle control mechanisms through local and remote effects. Postural balance is controlled by supraspinal (rambling) and spinal-peripheral (trembling) mechanisms. A manipulation may interfere with postural control in quiet standing. To evaluate the immediate effects of sacroiliac joint manipulation on postural control in patients with (1) sacroiliac dysfunction and (2) to determine whether rambling and trembling are affected by sacroiliac joint manipulation. 32 patients aged between 20 and 50 years old were selected by convenience after confirmation of sacroiliac joint dysfunction by clinical examination. These patients were randomly allocated either to manipulation or sham manipulation group. Displacement, velocity and frequency of the center of pressure, rambling and trembling in the anterior-posterior and medial-lateral directions were our primary outcomes and analyzed immediately before and after the intervention in quiet standing. The physical therapists who performed the physical, biomechanical and statistical examinations, were all blinded to the patients' grouping. No differences were found between the two groups but trembling velocity (0.14 and -0.11 for intervention and sham group, respectively) and frequency (0.17 and 0.11 for intervention and sham group respectively) increased after intervention in the treatment group in the anterior-posterior direction. Generally, sacroiliac joint manipulation had no superiority than sham treatment regarding postural control as measured by rambling-trembling analysis of center of pressure. Manipulation may increase muscle activation in the treatment group due to increased trembling parameters. Trial number: IRCT2014072715932N8 - http://www.irct.ir/searchresult.php?keyword=%D8%B3%D9%88%DB%8C%D9%87&id=15932&field=&number=8&prt=13&total=10&m=1. Copyright © 2017 Associação Brasileira de Pesquisa e Pós-Graduação em Fisioterapia. Publicado por Elsevier Editora Ltda. All rights reserved.

Changes in balance and joint position sense during a 12-day high altitude trek: The British Services Dhaulagiri medical research expedition.

PubMed

Clarke, Sarah B; Deighton, Kevin; Newman, Caroline; Nicholson, Gareth; Gallagher, Liam; Boos, Christopher J; Mellor, Adrian; Woods, David R; O'Hara, John P

2018-01-01

Postural control and joint position sense are essential for safely undertaking leisure and professional activities, particularly at high altitude. We tested whether exposure to a 12-day trek with a gradual ascent to high altitude impairs postural control and joint position sense. This was a repeated measures observational study of 12 military service personnel (28±4 years). Postural control (sway velocity measured by a portable force platform) during standing balance, a Sharpened Romberg Test and knee joint position sense were measured, in England (113m elevation) and at 3 research camps (3619m, 4600m and 5140m) on a 12-day high altitude trek in the Dhaulagiri region of Nepal. Pulse oximetry, and Lake Louise scores were also recorded on the morning and evening of each trek day. Data were compared between altitudes and relationships between pulse oximetry, Lake Louise score, and sway velocity were explored. Total sway velocity during standing balance with eyes open (p = 0.003, d = 1.9) and during Sharpened Romberg test with eyes open (p = 0.007, d = 1.6) was significantly greater at altitudes of 3619m and 5140m when compared with sea level. Anterior-posterior sway velocity during standing balance with eyes open was also significantly greater at altitudes of 3619m and 5140m when compared with sea level (p = 0.001, d = 1.9). Knee joint position sense was not altered at higher altitudes. There were no significant correlations between Lake Louise scores, pulse oximetry and postural sway. Despite a gradual ascent profile, exposure to 3619 m was associated with impairments in postural control without impairment in knee joint position sense. Importantly, these impairments did not worsen at higher altitudes of 4600 m or 5140 m. The present findings should be considered during future trekking expeditions when developing training strategies targeted to manage impairments in postural control that occur with increasing altitude.

[Exploration of a quantitative methodology to characterize the retention of PM2.5 and other atmospheric particulate matter by plant leaves: taking Populus tomentosa as an example].

PubMed

Zhang, Zhi-Dan; Xi, Ben-Ye; Cao, Zhi-Guo; Jia, Li-Ming

2014-08-01

Taking Populus tomentosa as an example, a methodology called elution-weighing-particle size-analysis (EWPA) was proposed to evaluate quantitatively the ability of retaining fine particulate matter (PM2.5, diameter d ≤ 2.5 μm) and atmospheric particulate matter by plant leaves using laser particle size analyzer and balance. This method achieved a direct, accurate measurement with superior operability about the quality and particle size distribution of atmospheric particulate matter retained by plant leaves. First, a pre-experiment was taken to test the stability of the method. After cleaning, centrifugation and drying, the particulate matter was collected and weighed, and then its particle size distribution was analyzed by laser particle size analyzer. Finally, the mass of particulate matter retained by unit area of leaf and stand was translated from the leaf area and leaf area index. This method was applied to a P. tomentosa stand which had not experienced rain for 27 days in Beijing Olympic Forest Park. The results showed that the average particle size of the atmospheric particulate matter retained by P. tomentosa was 17.8 μm, and the volume percentages of the retained PM2.5, inhalable particulate matter (PM10, d ≤ 10 μm) and total suspended particle (TSP, d ≤ 100 μm) were 13.7%, 47.2%, and 99.9%, respectively. The masses of PM2.5, PM10, TSP and total particulate matter were 8.88 x 10(-6), 30.6 x 10(-6), 64.7 x 10(-6) and 64.8 x 10(-6) g x cm(-2) respectively. The retention quantities of PM2.5, PM10, TSP and total particulate matter by the P. tomentosa stand were 0.963, 3.32, 7.01 and 7.02 kg x hm(-2), respectively.

Compact plane illumination plugin device to enable light sheet fluorescence imaging of multi-cellular organisms on an inverted wide-field microscope

PubMed Central

Guan, Zeyi; Lee, Juhyun; Jiang, Hao; Dong, Siyan; Jen, Nelson; Hsiai, Tzung; Ho, Chih-Ming; Fei, Peng

2015-01-01

We developed a compact plane illumination plugin (PIP) device which enabled plane illumination and light sheet fluorescence imaging on a conventional inverted microscope. The PIP device allowed the integration of microscope with tunable laser sheet profile, fast image acquisition, and 3-D scanning. The device is both compact, measuring approximately 15 by 5 by 5 cm, and cost-effective, since we employed consumer electronics and an inexpensive device molding method. We demonstrated that PIP provided significant contrast and resolution enhancement to conventional microscopy through imaging different multi-cellular fluorescent structures, including 3-D branched cells in vitro and live zebrafish embryos. Imaging with the integration of PIP greatly reduced out-of-focus contamination and generated sharper contrast in acquired 2-D plane images when compared with the stand-alone inverted microscope. As a result, the dynamic fluid domain of the beating zebrafish heart was clearly segmented and the functional monitoring of the heart was achieved. Furthermore, the enhanced axial resolution established by thin plane illumination of PIP enabled the 3-D reconstruction of the branched cellular structures, which leads to the improvement on the functionality of the wide field microscopy. PMID:26819828

Compact plane illumination plugin device to enable light sheet fluorescence imaging of multi-cellular organisms on an inverted wide-field microscope.

PubMed

Guan, Zeyi; Lee, Juhyun; Jiang, Hao; Dong, Siyan; Jen, Nelson; Hsiai, Tzung; Ho, Chih-Ming; Fei, Peng

2016-01-01

We developed a compact plane illumination plugin (PIP) device which enabled plane illumination and light sheet fluorescence imaging on a conventional inverted microscope. The PIP device allowed the integration of microscope with tunable laser sheet profile, fast image acquisition, and 3-D scanning. The device is both compact, measuring approximately 15 by 5 by 5 cm, and cost-effective, since we employed consumer electronics and an inexpensive device molding method. We demonstrated that PIP provided significant contrast and resolution enhancement to conventional microscopy through imaging different multi-cellular fluorescent structures, including 3-D branched cells in vitro and live zebrafish embryos. Imaging with the integration of PIP greatly reduced out-of-focus contamination and generated sharper contrast in acquired 2-D plane images when compared with the stand-alone inverted microscope. As a result, the dynamic fluid domain of the beating zebrafish heart was clearly segmented and the functional monitoring of the heart was achieved. Furthermore, the enhanced axial resolution established by thin plane illumination of PIP enabled the 3-D reconstruction of the branched cellular structures, which leads to the improvement on the functionality of the wide field microscopy.

The prevalence and clinical relevance of hyperkalaemia in calves with neonatal diarrhoea.

PubMed

Trefz, Florian M; Lorch, Annette; Feist, Melanie; Sauter-Louis, Carola; Lorenz, Ingrid

2013-03-01

One hundred and twenty-four calves with neonatal diarrhoea were investigated in order to assess the prevalence of hyperkalaemia and the associated clinical signs. Hyperkalaemia (potassium concentration >5.8mmol/L) was recognized in 42 (34%) calves and was more closely associated with dehydration than with decreases in base excess or venous blood pH. In 75 calves with normal blood concentrations of D-lactate (i.e. ⩽3.96mmol/L), K concentrations were moderately correlated with base excess values (r=-0.48, P<0.001). In contrast, no significant correlation was observed in 49 calves with elevated D-lactate. Only three hyperkalaemic calves had bradycardia and a weak positive correlation was found between heart rate and K concentrations (r=0.22, P=0.014). Ten of the 124 calves had cardiac arrhythmia and of these seven had hyperkalaemia indicating that cardiac arrhythmia had a low sensitivity (17%) but a high specificity (96%) as a predictor of hyperkalaemia. In a subset of 34 calves with base excess values ⩽-5mmol/L and D-lactate concentrations <5mmol/L (of which 22 had hyperkalaemia), changes in posture/ability to stand could be mainly explained by elevations of K concentrations (P<0.001) and to a lesser extent by increases in L-lactate concentrations (P=0.024). Skeletal muscle weakness due to hyperkalaemia alongside hypovolaemia may produce a clinical picture that is similar to that in calves with marked D-lactic acidosis. However, since reductions in the strength of the palpebral reflex are closely correlated with D-lactate concentrations, a prompt palpebral reflex can assist the clinical prediction of hyperkalaemia in calves presenting with a distinct impairment in their ability to stand (specificity 99%, sensitivity 29%). Copyright © 2012 Elsevier Ltd. All rights reserved.

Stand-alone front-end system for high- frequency, high-frame-rate coded excitation ultrasonic imaging.

PubMed

Park, Jinhyoung; Hu, Changhong; Shung, K Kirk

2011-12-01

A stand-alone front-end system for high-frequency coded excitation imaging was implemented to achieve a wider dynamic range. The system included an arbitrary waveform amplifier, an arbitrary waveform generator, an analog receiver, a motor position interpreter, a motor controller and power supplies. The digitized arbitrary waveforms at a sampling rate of 150 MHz could be programmed and converted to an analog signal. The pulse was subsequently amplified to excite an ultrasound transducer, and the maximum output voltage level achieved was 120 V(pp). The bandwidth of the arbitrary waveform amplifier was from 1 to 70 MHz. The noise figure of the preamplifier was less than 7.7 dB and the bandwidth was 95 MHz. Phantoms and biological tissues were imaged at a frame rate as high as 68 frames per second (fps) to evaluate the performance of the system. During the measurement, 40-MHz lithium niobate (LiNbO(3)) single-element lightweight (<;0.28 g) transducers were utilized. The wire target measure- ment showed that the -6-dB axial resolution of a chirp-coded excitation was 50 μm and lateral resolution was 120 μm. The echo signal-to-noise ratios were found to be 54 and 65 dB for the short burst and coded excitation, respectively. The contrast resolution in a sphere phantom study was estimated to be 24 dB for the chirp-coded excitation and 15 dB for the short burst modes. In an in vivo study, zebrafish and mouse hearts were imaged. Boundaries of the zebrafish heart in the image could be differentiated because of the low-noise operation of the implemented system. In mouse heart images, valves and chambers could be readily visualized with the coded excitation.

Diagnostic reliability of the cervical vertebral maturation method and standing height in the identification of the mandibular growth spurt.

PubMed

Perinetti, Giuseppe; Contardo, Luca; Castaldo, Attilio; McNamara, James A; Franchi, Lorenzo

2016-07-01

To evaluate the capability of both cervical vertebral maturation (CVM) stages 3 and 4 (CS3-4 interval) and the peak in standing height to identify the mandibular growth spurt throughout diagnostic reliability analysis. A previous longitudinal data set derived from 24 untreated growing subjects (15 females and nine males,) detailed elsewhere were reanalyzed. Mandibular growth was defined as annual increments in Condylion (Co)-Gnathion (Gn) (total mandibular length) and Co-Gonion Intersection (Goi) (ramus height) and their arithmetic mean (mean mandibular growth [mMG]). Subsequently, individual annual increments in standing height, Co-Gn, Co-Goi, and mMG were arranged according to annual age intervals, with the first and last intervals defined as 7-8 years and 15-16 years, respectively. An analysis was performed to establish the diagnostic reliability of the CS3-4 interval or the peak in standing height in the identification of the maximum individual increments of each Co-Gn, Co-Goi, and mMG measurement at each annual age interval. CS3-4 and standing height peak show similar but variable accuracy across annual age intervals, registering values between 0.61 (standing height peak, Co-Gn) and 0.95 (standing height peak and CS3-4, mMG). Generally, satisfactory diagnostic reliability was seen when the mandibular growth spurt was identified on the basis of the Co-Goi and mMG increments. Both CVM interval CS3-4 and peak in standing height may be used in routine clinical practice to enhance efficiency of treatments requiring identification of the mandibular growth spurt.

In Vivo Measurements of the Ischiofemoral Space in Recreationally Active Participants During Dynamic Activities: A High-Speed Dual Fluoroscopy Study.

PubMed

Atkins, Penny R; Fiorentino, Niccolo M; Aoki, Stephen K; Peters, Christopher L; Maak, Travis G; Anderson, Andrew E

2017-10-01

Ischiofemoral impingement (IFI) is a dynamic process, but its diagnosis is often based on static, supine images. To couple 3-dimensional (3D) computed tomography (CT) models with dual fluoroscopy (DF) images to quantify in vivo hip motion and the ischiofemoral space (IFS) in asymptomatic participants during weightbearing activities and evaluate the relationship of dynamic measurements with sex, hip kinematics, and the IFS measured from axial magnetic resonance imaging (MRI). Cross-sectional study; Level of evidence, 3. Eleven young, asymptomatic adults (5 female) were recruited. 3D reconstructions of the femur and pelvis were generated from MRI and CT. The axial and 3D IFS were measured from supine MRI. In vivo hip motion during weightbearing activities was quantified using DF. The bone-to-bone distance between the lesser trochanter and ischium was measured dynamically. The minimum and maximum IFS were determined and evaluated against hip joint angles using a linear mixed-effects model. The minimum IFS occurred during external rotation for 10 of 11 participants. The IFS measured from axial MRI (mean, 23.7 mm [95% CI, 19.9-27.9]) was significantly greater than the minimum IFS observed during external rotation (mean, 10.8 mm [95% CI, 8.3-13.7]; P < .001), level walking (mean, 15.5 mm [95% CI, 11.4-19.7]; P = .007), and incline walking (mean, 15.8 mm [95% CI, 11.6-20.1]; P = .004) but not for standing. The IFS was reduced with extension (β = 0.66), adduction (β = 0.22), and external rotation (β = 0.21) ( P < .001 for all) during the dynamic activities observed. The IFS was smaller in female than male participants for standing (mean, 20.9 mm [95% CI, 19.3-22.3] vs 30.4 mm [95% CI, 27.2-33.8], respectively; P = .034), level walking (mean, 8.8 mm [95% CI, 7.5-9.9] vs 21.1 mm [95% CI, 18.7-23.6], respectively; P = .001), and incline walking (mean, 9.1 mm [95% CI, 7.4-10.8] vs 21.3 mm [95% CI, 18.8-24.1], respectively; P = .003). Joint angles between the sexes were not significantly different for any of the dynamic positions of interest. The minimum IFS during dynamic activities was smaller than axial MRI measurements. Compared with male participants, the IFS in female participants was reduced during standing and walking, despite a lack of kinematic differences between the sexes. The relationship between the IFS and hip joint angles suggests that the hip should be placed into greater extension, adduction, and external rotation in clinical examinations and imaging, as the IFS measured from static images, especially in a neutral orientation, may not accurately represent the minimum IFS during dynamic motion. Nevertheless, this statement must be interpreted with caution, as only asymptomatic participants were analyzed herein.

Relationship between physical performance and self-reported function in healthy individuals across the lifespan.

PubMed

Baldwin, Jennifer N; McKay, Marnee J; Hiller, Claire E; Moloney, Niamh; Nightingale, Elizabeth J; Burns, Joshua

2017-08-01

Functional outcome measures in clinical trials of musculoskeletal conditions need to be meaningful to individuals. To investigate the relationship between physical performance and self/proxy-reported function in 1000 healthy children and adults. Cross-sectional observational study (1000 Norms Project). One thousand males and females aged 3-101 years, healthy by self-report and without major physical disability, were recruited. Twelve performance-based tests were analysed: vertical and long jump, two hand dexterity tests, four balance tests, stepping reaction time, 30-second chair stand, timed up-and-down stairs, and six-minute walk. Self/proxy-reported function was assessed using the Infant-Toddler Quality of Life questionnaire, Child Health Questionnaire, Assessment of Quality of Life (AQoL)-6D Adolescent, AQoL-8D, International Physical Activity Questionnaire and work ability question. Bivariate and multivariate correlational analyses were constructed for infants (3-4y), children (5-10y), adolescents (11-17y), adults (18-59y) and older adults (60+). Socio-demographic characteristics were similar to the Australian population. Among infants/children, greater jump and sit-to-stand performance correlated with higher proxy-reported function (p < 0.05). There were no significant relationships observed for adolescents (p > 0.05). Greater jump, dexterity, balance, reaction time, sit-to-stand, stair-climbing and six-minute walk performance correlated with higher self-reported function in adults (r = -0.097 to.231; p < 0.05) and older adults (r = -0.135 to 0.625; p < 0.05). Multivariate regression modelling revealed a collection of independent performance measures explaining up to 46% of the variance in self/proxy-reported function. Many performance-based tests were significantly associated with self/proxy-reported function. We have identified a set of physical measures which could form the basis of age-appropriate functional scales for clinical trials of musculoskeletal conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

KSC-06pd1229

NASA Image and Video Library

2006-06-26

KENNEDY SPACE CENTER, FLA. - At Astrotech Space Operations in Titusville, Fla., technicians prepare to deploy the solar panel on the STEREO observatory "A." STEREO, which stands for Solar Terrestrial Relations Observatory, consists of two spacecraft whose mission is to take measurements of the sun and solar wind in 3-D, for the first time. This new view will improve our understanding of space weather and its impact on the Earth. Preparations are under way for a liftoff aboard a Delta rocket no earlier than July 30. Photo credit: NASA/George Shelton

KSC-06pd1233

NASA Image and Video Library

2006-06-26

KENNEDY SPACE CENTER, FLA. - At Astrotech Space Operations in Titusville, Fla., the deployed solar panel on the STEREO observatory "A" undergoes testing. STEREO, which stands for Solar Terrestrial Relations Observatory, consists of two spacecraft whose mission is to take measurements of the sun and solar wind in 3-D, for the first time. This new view will improve our understanding of space weather and its impact on the Earth. Preparations are under way for a liftoff aboard a Delta rocket no earlier than July 30. Photo credit: NASA/George Shelton

KSC-06pd1232

NASA Image and Video Library

2006-06-26

KENNEDY SPACE CENTER, FLA. - At Astrotech Space Operations in Titusville, Fla., engineers perform testing on the solar panel on the STEREO observatory "A." STEREO, which stands for Solar Terrestrial Relations Observatory, consists of two spacecraft whose mission is to take measurements of the sun and solar wind in 3-D, for the first time. This new view will improve our understanding of space weather and its impact on the Earth. Preparations are under way for a liftoff aboard a Delta rocket no earlier than July 30. Photo credit: NASA/George Shelton

KSC-06pd1231

NASA Image and Video Library

2006-06-26

KENNEDY SPACE CENTER, FLA. - At Astrotech Space Operations in Titusville, Fla., the deployed solar panel on the STEREO observatory "A" undergoes testing. STEREO, which stands for Solar Terrestrial Relations Observatory, consists of two spacecraft whose mission is to take measurements of the sun and solar wind in 3-D, for the first time. This new view will improve our understanding of space weather and its impact on the Earth. Preparations are under way for a liftoff aboard a Delta rocket no earlier than July 30. Photo credit: NASA/George Shelton

Work function of few layer graphene covered nickel thin films measured with Kelvin probe force microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eren, B.; Material Sciences Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, California 94720; Gysin, U.

2016-01-25

Few layer graphene and graphite are simultaneously grown on a ∼100 nm thick polycrystalline nickel film. The work function of few layer graphene/Ni is found to be 4.15 eV with a variation of 50 meV by local measurements with Kelvin probe force microscopy. This value is lower than the work function of free standing graphene due to peculiar electronic structure resulting from metal 3d-carbon 2p(π) hybridization.

Space Shuttle Projects

NASA Image and Video Library

1983-11-08

The crew assigned to the STS-41B (STS-11) mission included (seated left to right) Vance D. Brand, commander; and Robert L. Gibson, pilot. Standing left to right are mission specialists Robert L. Stewart, Ronald E. McNair, and Bruce McCandless. Launched aboard the Space Shuttle Challenger on February 3, 1984 at 8:00:00 am (EST), the STS-41B mission marked the first untethered space walks which were performed by McCandless and Stewart. The crew deployed the WESTAR-VI and PALAPA-B2 satellites.