A readout system for X-ray powder crystallography

NASA Astrophysics Data System (ADS)

Loukas, D.; Haralabidis, N.; Pavlidis, A.; Karvelas, E.; Psycharis ^a, K. Misiakos, V.; Mousa, J.; Dre, Ch.

2000-06-01

A system for capturing and processing data, from radiation detectors, in the field of X-ray crystallography has been developed. The system includes a custom-made mixed analog-digital 16-channel VLSI circuit in 50 μm pitch. Each channel comprises a charge amplifier, a shaper, a comparator and a 21-bit counter. The circuit can be scaled in a daisy chain configuration. Data acquisition is performed with a custom made PCI card while the control software is developed with Visual C++ under the MS Windows NT environment. Performance of a fully operational system, in terms of electronic noise, statistical variations and data capture speed is presented. The noise level permits counting of X-rays down to 8 keV while the counting capability is in excess of 200 kHz. The system is intended for X-ray crystallography with silicon detectors.

75 FR 67347 - Marine Mammals; File No. 14326

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-02

...(s): Permits, Conservation and Education Division, Office of Protected Resources, NMFS, 1315 East... amended permit allows takes of up to 20 adult female Steller sea lions annually by capture using... the ESA. Dated: October 27, 2010. Tammy C. Adams, Acting Chief, Permits, Conservation and Education...

77 FR 5045 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-01

... take (survey, capture, handle, and release) the California tiger salamander (Ambystoma californiense..., capture, handle, and release) the California tiger salamander (Ambystoma californiense) and arroyo toad...

78 FR 55091 - Endangered and Threatened Species Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-09

... new permit for research and recovery purposes to conduct presence/absence surveys of golden-cheeked... amendment to a current permit for research and recovery purposes to capture and transport Gila chub (Gila... for research and recovery purposes to conduct presence/absence surveys of southwestern willow...

Capture and X-ray diffraction studies of protein microcrystals in a microfluidic trap array

DOE PAGES

Lyubimov, Artem Y.; Murray, Thomas D.; Koehl, Antoine; ...

2015-03-27

X-ray free-electron lasers (XFELs) promise to enable the collection of interpretable diffraction data from samples that are refractory to data collection at synchrotron sources. At present, however, more efficient sample-delivery methods that minimize the consumption of microcrystalline material are needed to allow the application of XFEL sources to a wide range of challenging structural targets of biological importance. Here, a microfluidic chip is presented in which microcrystals can be captured at fixed, addressable points in a trap array from a small volume (<10 µl) of a pre-existing slurry grown off-chip. The device can be mounted on a standard goniostat formore » conducting diffraction experiments at room temperature without the need for flash-cooling. Proof-of-principle tests with a model system (hen egg-white lysozyme) demonstrated the high efficiency of the microfluidic approach for crystal harvesting, permitting the collection of sufficient data from only 265 single-crystal still images to permit determination and refinement of the structure of the protein. This work shows that microfluidic capture devices can be readily used to facilitate data collection from protein microcrystals grown in traditional laboratory formats, enabling analysis when cryopreservation is problematic or when only small numbers of crystals are available. Such microfluidic capture devices may also be useful for data collection at synchrotron sources.« less

Capture and X-ray diffraction studies of protein microcrystals in a microfluidic trap array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyubimov, Artem Y.; Murray, Thomas D.; Koehl, Antoine

X-ray free-electron lasers (XFELs) promise to enable the collection of interpretable diffraction data from samples that are refractory to data collection at synchrotron sources. At present, however, more efficient sample-delivery methods that minimize the consumption of microcrystalline material are needed to allow the application of XFEL sources to a wide range of challenging structural targets of biological importance. Here, a microfluidic chip is presented in which microcrystals can be captured at fixed, addressable points in a trap array from a small volume (<10 µl) of a pre-existing slurry grown off-chip. The device can be mounted on a standard goniostat formore » conducting diffraction experiments at room temperature without the need for flash-cooling. Proof-of-principle tests with a model system (hen egg-white lysozyme) demonstrated the high efficiency of the microfluidic approach for crystal harvesting, permitting the collection of sufficient data from only 265 single-crystal still images to permit determination and refinement of the structure of the protein. This work shows that microfluidic capture devices can be readily used to facilitate data collection from protein microcrystals grown in traditional laboratory formats, enabling analysis when cryopreservation is problematic or when only small numbers of crystals are available. Such microfluidic capture devices may also be useful for data collection at synchrotron sources.« less

Neural system applied on an invariant industrial character recognition

NASA Astrophysics Data System (ADS)

Lecoeuche, Stephane; Deguillemont, Denis; Dubus, Jean-Paul

1997-04-01

Besides the variety of fonts, character recognition systems for the industrial world are confronted with specific problems like: the variety of support (metal, wood, paper, ceramics . . .) as well as the variety of marking (printing, engraving, . . .) and conditions of lighting. We present a system that is able to solve a part of this problem. It implements a collaboration between two neural networks. The first network specialized in vision allows the system to extract the character from an image. Besides this capability, we have equipped our system with characteristics allowing it to obtain an invariant model from the presented character. Thus, whatever the position, the size and the orientation of the character during the capture are, the model presented to the input of the second network will be identical. The second network, thanks to a learning phase, permits us to obtain a character recognition system independent of the type of fonts used. Furthermore, its capabilities of generalization permit us to recognize degraded and/or distorted characters. A feedback loop between the two networks permits the first one to modify the quality of vision.The cooperation between these two networks allows us to recognize characters whatever the support and the marking.

75 FR 20857 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-21

... 2, 2003, 68 FR 67465) to take (survey, capture, handle, and release) the California tiger salamander... tiger salamander (Ambystoma californiense) and to take (capture, collect, and kill) the Conservancy...

78 FR 24768 - Endangered and Threatened Wildlife and Plants; Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R3-ES-2013-N094; FXES11130300000F3-234... Service, Interior. ACTION: Notice of availability of permit applications; request for comments. SUMMARY... Survey and Design, LLC, Temperance, MI. The applicant requests a permit to take (capture and release...

77 FR 48130 - Marine Mammals; File No. 17152

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-13

... harbor seals are requested over the duration of the permit. Each year, up to 2,500 northern elephant seals (Mirounga angustirostris) will be handled for marking without capture; up to 100 elephant seals will be handled for swab sampling without capture; up to 150 elephant seals will be captured, marked...

Low-cost human motion capture system for postural analysis onboard ships

NASA Astrophysics Data System (ADS)

Nocerino, Erica; Ackermann, Sebastiano; Del Pizzo, Silvio; Menna, Fabio; Troisi, Salvatore

2011-07-01

The study of human equilibrium, also known as postural stability, concerns different research sectors (medicine, kinesiology, biomechanics, robotics, sport) and is usually performed employing motion analysis techniques for recording human movements and posture. A wide range of techniques and methodologies has been developed, but the choice of instrumentations and sensors depends on the requirement of the specific application. Postural stability is a topic of great interest for the maritime community, since ship motions can make demanding and difficult the maintenance of the upright stance with hazardous consequences for the safety of people onboard. The need of capturing the motion of an individual standing on a ship during its daily service does not permit to employ optical systems commonly used for human motion analysis. These sensors are not designed for operating in disadvantageous environmental conditions (water, wetness, saltiness) and with not optimal lighting. The solution proposed in this study consists in a motion acquisition system that could be easily usable onboard ships. It makes use of two different methodologies: (I) motion capture with videogrammetry and (II) motion measurement with Inertial Measurement Unit (IMU). The developed image-based motion capture system, made up of three low-cost, light and compact video cameras, was validated against a commercial optical system and then used for testing the reliability of the inertial sensors. In this paper, the whole process of planning, designing, calibrating, and assessing the accuracy of the motion capture system is reported and discussed. Results from the laboratory tests and preliminary campaigns in the field are presented.

75 FR 33633 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-14

..., handle, kill and remove from the wild) the California tiger salamander (Ambystoma californiense) in..., handle, and release) the California tiger salamander (Ambystoma californiense) in conjunction with... applicant requests a permit to take (survey, capture, handle, and release) the California tiger salamander...

76 FR 31942 - Marine Mammals; File No. 14329

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-02

... appointment in the following offices: Permits, Conservation and Education Division, Office of Protected... sampling and instrument attachment for lactating female fur seals already authorized for capture, and..., 2011. P. Michael Payne, Chief, Permits, Conservation and Education Division, Office of Protected...

Minimum required capture radius in a coplanar model of the aerial combat problem

NASA Technical Reports Server (NTRS)

Breakwell, J. V.; Merz, A. W.

1977-01-01

Coplanar aerial combat is modeled with constant speeds and specified turn rates. The minimum capture radius which will always permit capture, regardless of the initial conditions, is calculated. This 'critical' capture radius is also the maximum range which the evader can guarantee indefinitely if the initial range, for example, is large. A composite barrier is constructed which gives the boundary, at any heading, of relative positions for which the capture radius is less than critical.

78 FR 16703 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-18

... California tiger salamander (Santa Barbara County DPS and Sonoma County DPS) (Ambystoma californiense) in... requests a permit to take (harass by survey, capture, handle, and release) the California tiger salamander... tiger salamander (Santa Barbara County DPS) (Ambystoma californiense) in conjunction with surveys and...

78 FR 55287 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-10

... requests a permit to take (harass by survey, capture, handle, and release) the California tiger salamander...) the California tiger salamander (Santa Barbara County DPS and Sonoma County DPS) (Ambystoma...) the California tiger salamander (Santa Barbara County DPS and Sonoma County DPS) (Ambystoma...

Control Method for Video Guidance Sensor System

NASA Technical Reports Server (NTRS)

Howard, Richard T. (Inventor); Book, Michael L. (Inventor); Bryan, Thomas C. (Inventor)

2005-01-01

A method is provided for controlling operations in a video guidance sensor system wherein images of laser output signals transmitted by the system and returned from a target are captured and processed by the system to produce data used in tracking of the target. Six modes of operation are provided as follows: (i) a reset mode; (ii) a diagnostic mode; (iii) a standby mode; (iv) an acquisition mode; (v) a tracking mode; and (vi) a spot mode wherein captured images of returned laser signals are processed to produce data for all spots found in the image. The method provides for automatic transition to the standby mode from the reset mode after integrity checks are performed and from the diagnostic mode to the reset mode after diagnostic operations are commands is permitted only when the system is in the carried out. Further, acceptance of reset and diagnostic standby mode. The method also provides for automatic transition from the acquisition mode to the tracking mode when an acceptable target is found.

Control method for video guidance sensor system

NASA Technical Reports Server (NTRS)

Howard, Richard T. (Inventor); Book, Michael L. (Inventor); Bryan, Thomas C. (Inventor)

2005-01-01

A method is provided for controlling operations in a video guidance sensor system wherein images of laser output signals transmitted by the system and returned from a target are captured and processed by the system to produce data used in tracking of the target. Six modes of operation are provided as follows: (i) a reset mode; (ii) a diagnostic mode; (iii) a standby mode; (iv) an acquisition mode; (v) a tracking mode; and (vi) a spot mode wherein captured images of returned laser signals are processed to produce data for all spots found in the image. The method provides for automatic transition to the standby mode from the reset mode after integrity checks are performed and from the diagnostic mode to the reset mode after diagnostic operations are carried out. Further, acceptance of reset and diagnostic commands is permitted only when the system is in the standby mode. The method also provides for automatic transition from the acquisition mode to the tracking mode when an acceptable target is found.

Silica Aerogel Captures Cosmic Dust Intact

NASA Technical Reports Server (NTRS)

Tsou, P.

1994-01-01

The mesostructure of silica aerogel resembles stings of grapes, ranging in size from 10 to 100 angstrom. This fine mesostructure transmits nearly 90 percent of incident light in the visible, while providing sufficiently gentle dissipation of the kinetric energy of hypervelocity cosmic dust particles to permit their intact capture. We introduced silica aerogel in 1987 as capture medium to take advantage of its low density, fine mesostruicture and most importantly, its transparency, allowing optical location of captured micron sized particles.

78 FR 17359 - Endangered Species; File No. 17095-01

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-21

...: Monitor shortnose and Atlantic sturgeon abundance and distribution through the Hudson River Biological.../or larvae (ELS) annually. To account for a higher than expected catch per tow sampling performed... sturgeon captured over the permit life. The Permit Holder will also expand the sampling activities for...

An Expertise Recommender using Web Mining

NASA Technical Reports Server (NTRS)

Joshi, Anupam; Chandrasekaran, Purnima; ShuYang, Michelle; Ramakrishnan, Ramya

2001-01-01

This report explored techniques to mine web pages of scientists to extract information regarding their expertise, build expertise chains and referral webs, and semi automatically combine this information with directory information services to create a recommender system that permits query by expertise. The approach included experimenting with existing techniques that have been reported in research literature in recent past , and adapted them as needed. In addition, software tools were developed to capture and use this information.

Image BOSS: a biomedical object storage system

NASA Astrophysics Data System (ADS)

Stacy, Mahlon C.; Augustine, Kurt E.; Robb, Richard A.

1997-05-01

Researchers using biomedical images have data management needs which are oriented perpendicular to clinical PACS. The image BOSS system is designed to permit researchers to organize and select images based on research topic, image metadata, and a thumbnail of the image. Image information is captured from existing images in a Unix based filesystem, stored in an object oriented database, and presented to the user in a familiar laboratory notebook metaphor. In addition, the ImageBOSS is designed to provide an extensible infrastructure for future content-based queries directly on the images.

Wake Vortex Wingtip-Turbine Powered Circulation Control High-Lift System

NASA Technical Reports Server (NTRS)

Moore, Mark D.

2005-01-01

NASA s Vehicle Systems Program is investing in aeronautics technology development across six vehicle sectors, in order to improve future air travel. These vehicle sectors include subsonic commercial transports, supersonic vehicles, Uninhabited Aerial Vehicles (UAVs), Extreme Short Takeoff and Landing (ESTOL) vehicles, Rotorcraft, and Personal Air Vehicles (PAVs). While the subsonic transport is firmly established in U.S. markets, the other vehicle sectors have not developed a sufficient technology or regulatory state to permit widespread, practical use. The PAV sector has legacy products in the General Aviation (GA) market, but currently only accounts for negligible revenue miles, sales, or market share of personal travel. In order for PAV s to ever capture a significant market, these small aircraft require technologies that permit them to be less costly, environmentally acceptable, safer, easier to operate, more efficient, and less dependent on large support infrastructures.

Fast Metabolic Response to Drug Intervention through Analysis on a Miniaturized, Highly Integrated Molecular Imaging System

PubMed Central

Wang, Jun; Hwang, Kiwook; Braas, Daniel; Dooraghi, Alex; Nathanson, David; Campbell, Dean O.; Gu, Yuchao; Sandberg, Troy; Mischel, Paul; Radu, Caius; Chatziioannou, Arion F.; Phelps, Michael E.; Christofk, Heather; Heath, James R.

2014-01-01

We report on a radiopharmaceutical imaging platform designed to capture the kinetics of cellular responses to drugs. Methods A portable in vitro molecular imaging system, comprised of a microchip and a beta-particle imaging camera, permits routine cell-based radioassays on small number of either suspension or adherent cells. We investigate the response kinetics of model lymphoma and glioblastoma cancer cell lines to [18F]fluorodeoxyglucose ([18F]FDG) uptake following drug exposure. Those responses are correlated with kinetic changes in the cell cycle, or with changes in receptor-tyrosine kinase signaling. Results The platform enables radioassays directly on multiple cell types, and yields results comparable to conventional approaches, but uses smaller sample sizes, permits a higher level of quantitation, and doesn’t require cell lysis. Conclusion The kinetic analysis enabled by the platform provides a rapid (~1 hour) drug screening assay. PMID:23978446

77 FR 2311 - Endangered and Threatened Wildlife and Plants; Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-17

... endangered species in the Code of Federal Regulations (CFR) at 50 CFR 17. Submit your written data, comments..., Ozark big-eared bats (Corynorhinus townsendii ingens), Virginia big-eared bats (Corynorhinus townsendii... requests a permit renewal to take (capture and release) Indiana bats, gray bats, Virginia big-eared bats...

76 FR 61344 - Endangered and Threatened Species; Take of Anadromous Fish

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-04

... and Threatened Species; Take of Anadromous Fish AGENCY: National Marine Fisheries Service (NMFS... to the ESA and NMFS regulations (50 CFR parts 222-226) governing listed fish and wildlife permits... fish captured. Permit 15824 does not authorize any non- lethal or lethal take of adult ESA-listed...

75 FR 22738 - Endangered and Threatened Species; Take of Anadromous Fish

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-30

... and Threatened Species; Take of Anadromous Fish AGENCY: National Marine Fisheries Service (NMFS... seq.) and regulations governing listed fish and wildlife permits (50 CFR 222-226). NMFS issues permits... of toxicants). The KWIAHT would capture fish (using beach seines); measure them; check them for marks...

The Ohio River Valley CO2 Storage Project AEP Mountaineer Plan, West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neeraj Gupta

2009-01-07

This report includes an evaluation of deep rock formations with the objective of providing practical maps, data, and some of the issues considered for carbon dioxide (CO{sub 2}) storage projects in the Ohio River Valley. Injection and storage of CO{sub 2} into deep rock formations represents a feasible option for reducing greenhouse gas emissions from coal-burning power plants concentrated along the Ohio River Valley area. This study is sponsored by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL), American Electric Power (AEP), BP, Ohio Coal Development Office, Schlumberger, and Battelle along with its Pacific Northwest Division. Anmore » extensive program of drilling, sampling, and testing of a deep well combined with a seismic survey was used to characterize the local and regional geologic features at AEP's 1300-megawatt (MW) Mountaineer Power Plant. Site characterization information has been used as part of a systematic design feasibility assessment for a first-of-a-kind integrated capture and storage facility at an existing coal-fired power plant in the Ohio River Valley region--an area with a large concentration of power plants and other emission sources. Subsurface characterization data have been used for reservoir simulations and to support the review of the issues relating to injection, monitoring, strategy, risk assessment, and regulatory permitting. The high-sulfur coal samples from the region have been tested in a capture test facility to evaluate and optimize basic design for a small-scale capture system and eventually to prepare a detailed design for a capture, local transport, and injection facility. The Ohio River Valley CO{sub 2} Storage Project was conducted in phases with the ultimate objectives of demonstrating both the technical aspects of CO{sub 2} storage and the testing, logistical, regulatory, and outreach issues related to conducting such a project at a large point source under realistic constraints. The site characterization phase was completed, laying the groundwork for moving the project towards a potential injection phase. Feasibility and design assessment activities included an assessment of the CO{sub 2} source options (a slip-stream capture system or transported CO{sub 2}); development of the injection and monitoring system design; preparation of regulatory permits; and continued stakeholder outreach.« less

Mobility and orientation aid for blind persons using artificial vision

NASA Astrophysics Data System (ADS)

Costa, Gustavo; Gusberti, Adrián; Graffigna, Juan Pablo; Guzzo, Martín; Nasisi, Oscar

2007-11-01

Blind or vision-impaired persons are limited in their normal life activities. Mobility and orientation of blind persons is an ever-present research subject because no total solution has yet been reached for these activities that pose certain risks for the affected persons. The current work presents the design and development of a device conceived on capturing environment information through stereoscopic vision. The images captured by a couple of video cameras are transferred and processed by configurable and sequential FPGA and DSP devices that issue action signals to a tactile feedback system. Optimal processing algorithms are implemented to perform this feedback in real time. The components selected permit portability; that is, to readily get used to wearing the device.

Large Pilot Scale Testing of Linde/BASF Post-Combustion CO 2 Capture Technology at the Abbott Coal-Fired Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Kevin C.

The work summarized in this report is the first step towards a project that will re-train and create jobs for personnel in the coal industry and continue regional economic development to benefit regions impacted by previous downturns. The larger project is aimed at capturing ~300 tons/day (272 metric tonnes/day) CO 2 at a 90% capture rate from existing coal- fired boilers at the Abbott Power Plant on the campus of University of Illinois (UI). It will employ the Linde-BASF novel amine-based advanced CO 2 capture technology, which has already shown the potential to be cost-effective, energy efficient and compact atmore » the 0.5-1.5 MWe pilot scales. The overall objective of the project is to design and install a scaled-up system of nominal 15 MWe size, integrate it with the Abbott Power Plant flue gas, steam and other utility systems, and demonstrate the viability of continuous operation under realistic conditions with high efficiency and capacity. The project will also begin to build a workforce that understands how to operate and maintain the capture plants by including students from regional community colleges and universities in the operation and evaluation of the capture system. This project will also lay the groundwork for follow-on projects that pilot utilization of the captured CO 2 from coal-fired power plants. The net impact will be to demonstrate a replicable means to (1) use a standardized procedure to evaluate power plants for their ability to be retrofitted with a pilot capture unit; (2) design and construct reliable capture systems based on the Linde-BASF technology; (3) operate and maintain these systems; (4) implement training programs with local community colleges and universities to establish a workforce to operate and maintain the systems; and (5) prepare to evaluate at the large pilot scale level various methods to utilize the resulting captured CO 2. Towards the larger project goal, the UI-led team, together with Linde, has completed a preliminary design for the carbon capture pilot plant with basic engineering and cost estimates, established permitting needs, identified approaches to address Environmental, Health, and Safety concerns related to pilot plant installation and operation, developed approaches for long-term use of the captured carbon, and established strategies for workforce development and job creation that will re-train coal operators to operate carbon capture plants. This report describes Phase I accomplishments and demonstrates that the project team is well-prepared for full implementation of Phase 2, to design, build, and operate the carbon capture pilot plant.« less

Depth measurements through controlled aberrations of projected patterns.

PubMed

Birch, Gabriel C; Tyo, J Scott; Schwiegerling, Jim

2012-03-12

Three-dimensional displays have become increasingly present in consumer markets. However, the ability to capture three-dimensional images in space confined environments and without major modifications to current cameras is uncommon. Our goal is to create a simple modification to a conventional camera that allows for three dimensional reconstruction. We require such an imaging system have imaging and illumination paths coincident. Furthermore, we require that any three-dimensional modification to a camera also permits full resolution 2D image capture.Here we present a method of extracting depth information with a single camera and aberrated projected pattern. A commercial digital camera is used in conjunction with a projector system with astigmatic focus to capture images of a scene. By using an astigmatic projected pattern we can create two different focus depths for horizontal and vertical features of a projected pattern, thereby encoding depth. By designing an aberrated projected pattern, we are able to exploit this differential focus in post-processing designed to exploit the projected pattern and optical system. We are able to correlate the distance of an object at a particular transverse position from the camera to ratios of particular wavelet coefficients.We present our information regarding construction, calibration, and images produced by this system. The nature of linking a projected pattern design and image processing algorithms will be discussed.

From orbital debris capture systems through internal combustion engines on Mars

NASA Technical Reports Server (NTRS)

1991-01-01

The investigation and conceptualization of an orbital debris collector was the primary area of design. In addition, an alternate structural design for Space Station Freedom and systems supporting resource utilization at Mars and the moon were studied. Hardware for production of oxygen from simulate Mars atmosphere was modified to permit more reliable operation at low pressures (down to 10 mb). An internal combustion engine was altered to study how Mars atmosphere could be used as a diluent to control combustion temperatures and avoid excess Mars propellant production requirements that would result from either methane-rich or oxygen-rich, methane-oxygen combustion. An elastic loop traction system that could be used for lunar construction vehicles was refined to permit testing. A parabolic heat rejection radiator system was designed and built to determine whether it was capable of increasing heat rejection rates during lunar daytime operation. In addition, an alternate space station truss design, utilizing a pre-integrated concept, was studied and found to reduce estimate extravehicular activity (EVA) time and increase the structural integrity when compared to the original Warren truss concept. An orbital-debris-capturing spacecraft design which could be mated with the Orbital Maneuvering Vehicle was studied. The design identified Soviet C-1B boosters as the best targets of opportunity in Earth orbits between an altitude of 900 km and 1100 km and at an inclination of 82.9 deg. A dual robot pallet, which could be spun to match the tumbling rate of the C-1B booster, was developed as the conceptual design.

77 FR 36581 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-19

... Conservation Act of 1978 AGENCY: National Science Foundation. ACTION: Notice of Permit Applications Received.... The presence of these animals pose operation safety concerns as well as potential harm to the animals... for capturing Antarctic fishes to study their physiology and biochemistry. Benthic Otter trawling is...

Solar-powered irrigation systems. Technical progress report, July 1977--January 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1978-02-28

Dispersed solar thermal power systems applied to farm irrigation energy needs are analyzed. The 17 western states, containing 84% of nationwide irrigated croplands and consuming 93% of nationwide irrigation energy, have been selected to determine were solar irrigation systems can compete most favorably with conventional energy sources. Financial analysis of farms, according to size and ownership, was accomplished to permit realistic comparative analyses of system lifetime costs. Market potential of optimized systems has been estimated for the 17-state region for near-term (1985) and intermediate-term (2000) applications. Technical, economic, and institutional factors bearing on penetration and capture of this market aremore » being identified.« less

The Physician's Workstation: Recording a Physical Examination Using a Controlled Vocabulary

PubMed Central

Cimino, James J.; Barnett, G. Octo

1987-01-01

A system has been developed which runs on MS-DOS personal computers and serves as an experimental model of a physician's workstation. The program provides an interface to a controlled vocabulary which allows rapid selection of appropriate terms and modifiers for entry of clinical information. Because it captures patient descriptions, it has the ability to serve as an intermediary between the physician and computer-based medical knowledge resources. At present, the vocabulary permits rapid, reliable representation of cardiac physical examination findings.

Model authoring system for fail safe analysis

NASA Technical Reports Server (NTRS)

Sikora, Scott E.

1990-01-01

The Model Authoring System is a prototype software application for generating fault tree analyses and failure mode and effects analyses for circuit designs. Utilizing established artificial intelligence and expert system techniques, the circuits are modeled as a frame-based knowledge base in an expert system shell, which allows the use of object oriented programming and an inference engine. The behavior of the circuit is then captured through IF-THEN rules, which then are searched to generate either a graphical fault tree analysis or failure modes and effects analysis. Sophisticated authoring techniques allow the circuit to be easily modeled, permit its behavior to be quickly defined, and provide abstraction features to deal with complexity.

Final Environmental Assessment Addressing Construction, Operation, and Maintenance of a Military Working Dog Facility at Kirtland Air Force Base, New Mexico

DTIC Science & Technology

2011-03-01

dove (Zenaida macroura), greater roadrunner (Geococcyx californianus), American crow (Cowus brachyrhynchos), northern mockingbird (Mimus polyglottos...permitted by regulations, the MBTA makes it unlawful to pursue, hunt, take, capture, or kill ; attempt to take, capture, or kill ; possess; offer to or...or through a foreign country, any bird, part, nest, or egg that was captured, killed , taken, shipped, transported, or carried contrary to the laws

Optimizing Aerobot Exploration of Venus

NASA Astrophysics Data System (ADS)

Ford, Kevin S.

1997-03-01

Venus Flyer Robot (VFR) is an aerobot; an autonomous balloon probe designed for remote exploration of Earth's sister planet in 2003. VFR's simple navigation and control system permits travel to virtually any location on Venus, but it can survive for only a limited duration in the harsh Venusian environment. To help address this limitation, we develop: (1) a global circulation model that captures the most important characteristics of the Venusian atmosphere; (2) a simple aerobot model that captures thermal restrictions faced by VFR at Venus; and (3) one exact and two heuristic algorithms that, using abstractions (1) and (2), construct routes making the best use of VFR's limited lifetime. We demonstrate this modeling by planning several small example missions and a prototypical mission that explores numerous interesting sites recently documented in the plane tary geology literature.

Optimizing Aerobot Exploration of Venus

NASA Technical Reports Server (NTRS)

Ford, Kevin S.

1997-01-01

Venus Flyer Robot (VFR) is an aerobot; an autonomous balloon probe designed for remote exploration of Earth's sister planet in 2003. VFR's simple navigation and control system permits travel to virtually any location on Venus, but it can survive for only a limited duration in the harsh Venusian environment. To help address this limitation, we develop: (1) a global circulation model that captures the most important characteristics of the Venusian atmosphere; (2) a simple aerobot model that captures thermal restrictions faced by VFR at Venus; and (3) one exact and two heuristic algorithms that, using abstractions (1) and (2), construct routes making the best use of VFR's limited lifetime. We demonstrate this modeling by planning several small example missions and a prototypical mission that explores numerous interesting sites recently documented in the plane tary geology literature.

CO2 Capture from the Air: Technology Assessment and Implications for Climate Policy

NASA Astrophysics Data System (ADS)

Keith, D. W.

2002-05-01

It is physically possible to capture CO2 directly from the air and immobilize it in geological structures. Today, there are no large-scale technologies that achieve air capture at reasonable cost. Yet, strong arguments suggest that it will comparatively easy to develop practical air capture technologies on the timescales relevant to climate policy [1]. This paper first analyzes the cost of air capture and then assesses the implications for climate policy. We first analyze the lower bound on the cost needed for air capture, describing the thermodynamic and physical limits to the use of energy and land. We then compare the costs of air capture to the cost of capture from combustion exhaust streams. While the intrinsic minimum energy requirement is larger for air capture, we argue that air capture has important structural advantages, such as the reduction of transport costs and the larger potential for economies of scale. These advantages suggest that, in the long-run air capture be competitive with other methods of achieving deep emissions reductions. We provide a preliminary engineering-economic analysis of an air capture system based on CaO to CaCO3 chemical looping [1]. We analyze the possibility of doing the calcination in a modified pressurized fluidized bed combustor (PFBC) burning coal in a CO2 rich atmosphere with oxygen supplied by an air separation unit. The CaCO3-to-coal ratio would be ~2:1 and the system would be nearly thermally neutral. PFBC systems have been demonstrated at capacities of over 100 MW. Such systems already include CaCO3 injection for sulfur control, and operate at suitable temperatures and pressures for calcination. We assess the potential to recover heat from the dissolution of CaO in order to reduce the overall energy requirements. We analyze the possibility of adapting existing large water/air heat exchangers for use as contacting systems to capture CO2 from the air using the calcium hydroxide solution. The implications of air capture for global climate policy are examined using DIAM [2], a stylized integrated assessment model. We find that air capture can fundamentally alter the temporal dynamics of global warming mitigation. The reason for this is that air capture differs from conventional mitigation in three key aspects. First, it removes emissions from any part of the economy with equal ease or difficulty, so its cost provides an absolute cap on the cost of mitigation. Second, it permits reduction in concentrations faster than the natural carbon cycle: the effects of irreversibility are thus partly alleviated. Third, because it is less coupled with the energy system, air capture may offer stronger economies of scale and smaller adjustment costs than the more conventional mitigation technologies. Air capture limits the total cost of a worst-case climate scenario. In an optimal sequential decision framework with uncertainty, existence of air capture decreases the need for near-term precautionary abatement. Like geoengineering, air capture thus poses a moral hazard. 1. S. Elliott, et al. Compensation of atmospheric CO2 buildup through engineered chemical sinkage. Geophys. Res. Let., 28:1235-1238, 2001. 2. Minh Ha-Duong, Michael J. Grubb, and Jean-Charles Hourcade. Influence of socioeconomic inertia and uncertainty on optimal CO2-emission abatement. Nature, 390: 270-274, 1997.

A multimodal 3D framework for fire characteristics estimation

NASA Astrophysics Data System (ADS)

Toulouse, T.; Rossi, L.; Akhloufi, M. A.; Pieri, A.; Maldague, X.

2018-02-01

In the last decade we have witnessed an increasing interest in using computer vision and image processing in forest fire research. Image processing techniques have been successfully used in different fire analysis areas such as early detection, monitoring, modeling and fire front characteristics estimation. While the majority of the work deals with the use of 2D visible spectrum images, recent work has introduced the use of 3D vision in this field. This work proposes a new multimodal vision framework permitting the extraction of the three-dimensional geometrical characteristics of fires captured by multiple 3D vision systems. The 3D system is a multispectral stereo system operating in both the visible and near-infrared (NIR) spectral bands. The framework supports the use of multiple stereo pairs positioned so as to capture complementary views of the fire front during its propagation. Multimodal registration is conducted using the captured views in order to build a complete 3D model of the fire front. The registration process is achieved using multisensory fusion based on visual data (2D and NIR images), GPS positions and IMU inertial data. Experiments were conducted outdoors in order to show the performance of the proposed framework. The obtained results are promising and show the potential of using the proposed framework in operational scenarios for wildland fire research and as a decision management system in fighting.

Estimating taxonomic diversity, extinction rates, and speciation rates from fossil data using capture-recapture models

USGS Publications Warehouse

Nichols, J.D.; Pollock, K.H.

1983-01-01

Capture-recapture models can be used to estimate parameters of interest from paleobiological data when encouter probabilities are unknown and variable over time. These models also permit estimation of sampling variances and goodness-of-fit tests are available for assessing the fit of data to most models. The authors describe capture-recapture models which should be useful in paleobiological analyses and discuss the assumptions which underlie them. They illustrate these models with examples and discuss aspects of study design.

Pressure induced swelling in microporous materials

DOEpatents

Vogt, Thomas; Hriljac, Joseph A.; Lee, Yongjae

2006-07-11

A method for capturing specified materials which includes contacting a microporous material with a hydrostatic fluid having at least one specified material carried therein, under pressure which structurally distorts the lattice sufficiently to permit entry of the at least one specified material. The microporous material is capable of undergoing a temporary structural distortion which alters resting lattice dimensions under increased ambient pressure and at least partially returning to rest lattice dimensions when returned to ambient pressure. The pressure of the fluid is then reduced to permit return to at least partial resting lattice dimension while the at least one specified material is therein. By this method, at least one specified material is captured in the microporous material to form a modified microporous material.

Approaches for the Direct estimation of rate of increase in population size (λ) using capture-recapture data

Treesearch

James D. Nichols; Scott T. Sillett; James E. Hines; Richard T. Holmes

2005-01-01

Recent developments in the modeling of capture-recapture data permit the direct estimation and modeling of population growth rate Pradel (1996). Resulting estimates reflect changes in numbers of birds on study areas, and such changes result from movement as well as survival and reproductive recruitment. One measure of the “importance” of a...

75 FR 23287 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-03

..., photograph, collect tissue, and release) the Santa Cruz long- toed salamander (Ambystoma macrodactylum croceum) and California tiger salamander (Ambystoma californiense); and take (survey, capture, handle...

76 FR 6490 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-04

...) to take (survey, capture, handle and release) the California tiger salamander (Ambystoma... 66668) to take (collect tissue samples) the California tiger salamander (Ambystoma californiense) in...

Instrumentation for a dry-pond detention study

USGS Publications Warehouse

Pope, L.M.; Jennings, M.E.; Thibodeaux, K.G.

1988-01-01

A 12.3-acre, fully urbanized, residential land-use catchment was instrumented by the U. S. Geological Survey in Topeka, Kansas. Hydraulic instrumentation for flow measurement includes two types of flumes, a pipe-insert flume and a culvert-inlet (manhole) flume. Samples of rainfall and runoff for water-quality analyses were collected by automatic, 3-liter, 24-sample capacity water samples controlled by multichannel data loggers. Ancillary equipment included a raingage and wet/dry atmospheric-deposition sampler. Nineteen stormwater runoff events were monitored at the site using the instrumentation system. The system has a high reliability of data capture and permits an accurate determination of storm-water loads.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Young-Ho; Lazauskas, Rimantas; Park, Tae-Sun

M1 properties, comprising magnetic moments and radiative capture of thermal neutron observables, are studied in two- and three-nucleon systems. We use meson exchange current derived up to N{sup 3}LO using heavy baryon chiral perturbation theory a la Weinberg. Calculations have been performed for several qualitatively different realistic nuclear Hamiltonians, which permits us to analyze model dependence of our results. Our results are found to be strongly correlated with the effective range parameters such as binding energies and the scattering lengths. Taking into account such correlations, the results are in good agreement with the experimental data with small model dependence.

Tile Drainage Expansion Detection using Satellite Soil Moisture Dynamics

NASA Astrophysics Data System (ADS)

Jacobs, J. M.; Cho, E.; Jia, X.

2017-12-01

In the past two decades, tile drainage installation has accelerated throughout the Red River of the North Basin (RRB) in parts of western Minnesota, eastern North Dakota, and a small area of northeastern South Dakota, because the flat topography and low-permeability soils in this region necessitated the removal of excess water to improve crop production. Interestingly, streamflow in the Red River has markedly increased and six of 13 major floods during the past century have occurred since the late 1990s. It has been suggested that the increase in RRB flooding could be due to change in agricultural practices, including extensive tile drainage installation. Reliable information on existing and future tile drainage installation is greatly needed to capture the rapid extension of tile drainage systems and to locate tile drainage systems in the north central U.S. including the RRB region. However, there are few reliable data of tile drainage installation records, except tile drainage permit records in the Bois de Sioux watershed (a sub-basin in southern part of the RRB where permits are required for tile drainage installation). This study presents a tile drainage expansion detection method based on a physical principle that the soil-drying rate may increase with increasing tile drainage for a given area. In order to capture the rate of change in soil drying rate with time over entire RRB (101,500 km2), two satellite-based microwave soil moisture records from the Advanced Microwave Scanning Radiometer for Earth Observing System (AMSR-E) and AMSR2 were used during 2002 to 2016. In this study, a sub-watershed level (HUC10) potential tile drainage growth map was developed and the results show good agreement with tile drainage permit records of six sub-watersheds in the Bois de Sioux watershed. Future analyses will include improvement of the potential tile drainage map through additional information using optical- and thermal-based sensor products and evaluation of its hydrological impacts on intensity, duration, and frequency of extreme streamflow from watershed to basin scale.

Global Eddy-Permitting Ocean Reanalyses and Simulations of the Period 1992 to Present

NASA Astrophysics Data System (ADS)

Parent, L.; Ferry, N.; Barnier, B.; Garric, G.; Bricaud, C.; Testut, C.-E.; Le Galloudec, O.; Lellouche, J.-M.; Greiner, E.; Drevillon, M.; Remy, E.; Moulines, J.-M.; Guinehut, S.; Cabanes, C.

2013-09-01

We present GLORYS2V1 global ocean and sea-ice eddy permitting reanalysis over the altimetric era (1993- 2009). This reanalysis is based on an ocean and sea-ice general circulation model at 1⁄4° horizontal resolution assimilating sea surface temperature, in situ profiles of temperature and salinity and along-track sea level anomaly observations. The reanalysis has been produced along with a reference simulation called MJM95 which allows evaluating the benefits of the data assimilation. In the introduction, we briefly describe the GLORYS2V1 reanalysis system. In sections 2, 3 and 4, the reanalysis skill is presented. Data assimilation diagnostics reveal that the reanalysis is stable all along the time period, with however an improved skill when Argo observation network establishes. GLORYS2V1 captures well climate signals and trends and describes meso-scale variability in a realistic manner.

Nonparametric estimation of stochastic differential equations with sparse Gaussian processes.

PubMed

García, Constantino A; Otero, Abraham; Félix, Paulo; Presedo, Jesús; Márquez, David G

2017-08-01

The application of stochastic differential equations (SDEs) to the analysis of temporal data has attracted increasing attention, due to their ability to describe complex dynamics with physically interpretable equations. In this paper, we introduce a nonparametric method for estimating the drift and diffusion terms of SDEs from a densely observed discrete time series. The use of Gaussian processes as priors permits working directly in a function-space view and thus the inference takes place directly in this space. To cope with the computational complexity that requires the use of Gaussian processes, a sparse Gaussian process approximation is provided. This approximation permits the efficient computation of predictions for the drift and diffusion terms by using a distribution over a small subset of pseudosamples. The proposed method has been validated using both simulated data and real data from economy and paleoclimatology. The application of the method to real data demonstrates its ability to capture the behavior of complex systems.

Experiments and simulation of a net closing mechanism for tether-net capture of space debris

NASA Astrophysics Data System (ADS)

Sharf, Inna; Thomsen, Benjamin; Botta, Eleonora M.; Misra, Arun K.

2017-10-01

This research addresses the design and testing of a debris containment system for use in a tether-net approach to space debris removal. The tether-net active debris removal involves the ejection of a net from a spacecraft by applying impulses to masses on the net, subsequent expansion of the net, the envelopment and capture of the debris target, and the de-orbiting of the debris via a tether to the chaser spacecraft. To ensure a debris removal mission's success, it is important that the debris be successfully captured and then, secured within the net. To this end, we present a concept for a net closing mechanism, which we believe will permit consistently successful debris capture via a simple and unobtrusive design. This net closing system functions by extending the main tether connecting the chaser spacecraft and the net vertex to the perimeter and around the perimeter of the net, allowing the tether to actuate closure of the net in a manner similar to a cinch cord. A particular embodiment of the design in a laboratory test-bed is described: the test-bed itself is comprised of a scaled-down tether-net, a supporting frame and a mock-up debris. Experiments conducted with the facility demonstrate the practicality of the net closing system. A model of the net closure concept has been integrated into the previously developed dynamics simulator of the chaser/tether-net/debris system. Simulations under tether tensioning conditions demonstrate the effectiveness of the closure concept for debris containment, in the gravity-free environment of space, for a realistic debris target. The on-ground experimental test-bed is also used to showcase its utility for validating the dynamics simulation of the net deployment, and a full-scale automated setup would make possible a range of validation studies of other aspects of a tether-net debris capture mission.

Assessing barriers to health insurance and threats to equity in comparative perspective: The Health Insurance Access Database

PubMed Central

2012-01-01

Background Typologies traditionally used for international comparisons of health systems often conflate many system characteristics. To capture policy changes over time and by service in health systems regulation of public and private insurance, we propose a database containing explicit, standardized indicators of policy instruments. Methods The Health Insurance Access Database (HIAD) will collect policy information for ten OECD countries, over a range of eight health services, from 1990–2010. Policy indicators were selected through a comprehensive literature review which identified policy instruments most likely to constitute barriers to health insurance, thus potentially posing a threat to equity. As data collection is still underway, we present here the theoretical bases and methodology adopted, with a focus on the rationale underpinning the study instruments. Results These harmonized data will allow the capture of policy changes in health systems regulation of public and private insurance over time and by service. The standardization process will permit international comparisons of systems’ performance with regards to health insurance access and equity. Conclusion This research will inform and feed the current debate on the future of health care in developed countries and on the role of the private sector in these changes. PMID:22551599

Storage, retrieval, and edit of digital video using Motion JPEG

NASA Astrophysics Data System (ADS)

Sudharsanan, Subramania I.; Lee, D. H.

1994-04-01

In a companion paper we describe a Micro Channel adapter card that can perform real-time JPEG (Joint Photographic Experts Group) compression of a 640 by 480 24-bit image within 1/30th of a second. Since this corresponds to NTSC video rates at considerably good perceptual quality, this system can be used for real-time capture and manipulation of continuously fed video. To facilitate capturing the compressed video in a storage medium, an IBM Bus master SCSI adapter with cache is utilized. Efficacy of the data transfer mechanism is considerably improved using the System Control Block architecture, an extension to Micro Channel bus masters. We show experimental results that the overall system can perform at compressed data rates of about 1.5 MBytes/second sustained and with sporadic peaks to about 1.8 MBytes/second depending on the image sequence content. We also describe mechanisms to access the compressed data very efficiently through special file formats. This in turn permits creation of simpler sequence editors. Another advantage of the special file format is easy control of forward, backward and slow motion playback. The proposed method can be extended for design of a video compression subsystem for a variety of personal computing systems.

77 FR 70456 - Receipt of Applications for Endangered Species Permits

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... authorization to conduct scientific research involving capture and handling of reticulated flatwoods salamanders (Ambystoma bishop) and frosted flatwoods salamanders (Ambystoma cingulatum). This study will be conducted in...

76 FR 68719 - Marine Mammals; File No. 16553

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-07

...), northern elephant seals (Mirounga angustirostris), and harbor seals (Phoca vitulina). ADDRESSES: The permit... species. California sea lions, northern elephant seals, and harbor seals may be captured and sampled at...

Minimizing capture-related stress on white-tailed deer with a capture collar

USGS Publications Warehouse

DelGiudice, G.D.; Kunkel, K.E.; Mech, L.D.; Seal, U.S.

1990-01-01

We compared the effect of 3 capture methods for white-tailed deer (Odocoileus virginianus) on blood indicators of acute excitement and stress from 1 February to 20 April 1989. Eleven adult females were captured by Clover trap or cannon net between 1 February and 9 April 1989 in northeastern Minnesota [USA]. These deer were fitted with radio-controlled capture collars, and 9 deer were recaptured 7-33 days later. Trapping method affected serum cortisol (P < 0.0001), hemoglobin (Hb) (P < 0.06), and packed cell volume (PCV) (P < 0.07). Cortisol concentrations were lower (P < 0.0001) in capture-collared deer (0.54 .+-. 0.07 [SE] .mu.g/dL) compared to Clover-trapped (4.37 .+-. 0.69 .mu.g/dL) and cannon-netted (3.88 .+-. 0.82 .mu.g/dL) deer. Capture-collared deer were minimally stressed compared to deer captured by traditional methods. Use of the capture collar should permit more accurate interpretation of blood profiles of deer for assessement of condition and general health.

Derivation of Rigid Body Analysis Models from Vehicle Architecture Abstractions

DTIC Science & Technology

2011-06-17

models of every type have their basis in some type of physical representation of the design domain. Rather than describing three-dimensional continua of...arrangement, while capturing just enough physical detail to be used as the basis for a meaningful representation of the design , and eventually, analyses that...permit architecture assessment. The design information captured by the abstractions is available at the very earliest stages of the vehicle

Influence of Siphonophore Behavior upon Their Natural Diets: Evidence for Aggressive Mimicry.

PubMed

Purcell, J E

1980-08-29

Collection by divers permitted determination of the natural diets of siphonophore species within II genera. Siphonophores that swim rapidly to spread their tentacles capture small prey, whereas those that swim very weakly capture much larger prey. Nematocyst batteries of two species of weak swimmers closely resemble copepods and fish larvae. Morphology, behavior, and diet suggest that these two species attract large prey by mimicking other zooplankton.

Environmental Assessment for the Construction and Operation of an Indoor Small Arms Range at Niagara Falls Air Reserve Station, New York

DTIC Science & Technology

2009-08-01

Name Northern flicker Colaptes auratus Northern harrier2 Circus cyaneus Northern mockingbird Mimus polyglottos Northern rough-winged swallow...Installation operations impact wildlife habitat. Disturbance of vegetation by construction. Displacement and potential to kill or injure...Unless otherwise permitted by regulations, the MBTA makes it unlawful to pursue, hunt, take, capture, or kill ; attempt to take, capture or kill

The Nano-Sat Exo-Brake Experiment: Status of the First Controlled De-Orbit (and Subsequent Experiments)

NASA Technical Reports Server (NTRS)

Murbach, M.; Guarneros Luna, A.; Alena, R.; Papadopoulos, P.; Stone, T.; Tanner, A.; Wheless, J.; Priscal, C.; Dono Perez, A.; Cianciolo, A;

A Last Glacial Maximum world-ocean simulation at eddy-permitting resolution - Part 1: Experimental design and basic evaluation

NASA Astrophysics Data System (ADS)

Ballarotta, M.; Brodeau, L.; Brandefelt, J.; Lundberg, P.; Döös, K.

2013-01-01

Most state-of-the-art climate models include a coarsely resolved oceanic component, which has difficulties in capturing detailed dynamics, and therefore eddy-permitting/eddy-resolving simulations have been developed to reproduce the observed World Ocean. In this study, an eddy-permitting numerical experiment is conducted to simulate the global ocean state for a period of the Last Glacial Maximum (LGM, ~ 26 500 to 19 000 yr ago) and to investigate the improvements due to taking into account these higher spatial scales. The ocean general circulation model is forced by a 49-yr sample of LGM atmospheric fields constructed from a quasi-equilibrated climate-model simulation. The initial state and the bottom boundary condition conform to the Paleoclimate Modelling Intercomparison Project (PMIP) recommendations. Before evaluating the model efficiency in representing the paleo-proxy reconstruction of the surface state, the LGM experiment is in this first part of the investigation, compared with a present-day eddy-permitting hindcast simulation as well as with the available PMIP results. It is shown that the LGM eddy-permitting simulation is consistent with the quasi-equilibrated climate-model simulation, but large discrepancies are found with the PMIP model analyses, probably due to the different equilibration states. The strongest meridional gradients of the sea-surface temperature are located near 40° N and S, this due to particularly large North-Atlantic and Southern-Ocean sea-ice covers. These also modify the locations of the convection sites (where deep-water forms) and most of the LGM Conveyor Belt circulation consequently takes place in a thinner layer than today. Despite some discrepancies with other LGM simulations, a glacial state is captured and the eddy-permitting simulation undertaken here yielded a useful set of data for comparisons with paleo-proxy reconstructions.

Simulating North American mesoscale convective systems with a convection-permitting climate model

NASA Astrophysics Data System (ADS)

Prein, Andreas F.; Liu, Changhai; Ikeda, Kyoko; Bullock, Randy; Rasmussen, Roy M.; Holland, Greg J.; Clark, Martyn

2017-10-01

Deep convection is a key process in the climate system and the main source of precipitation in the tropics, subtropics, and mid-latitudes during summer. Furthermore, it is related to high impact weather causing floods, hail, tornadoes, landslides, and other hazards. State-of-the-art climate models have to parameterize deep convection due to their coarse grid spacing. These parameterizations are a major source of uncertainty and long-standing model biases. We present a North American scale convection-permitting climate simulation that is able to explicitly simulate deep convection due to its 4-km grid spacing. We apply a feature-tracking algorithm to detect hourly precipitation from Mesoscale Convective Systems (MCSs) in the model and compare it with radar-based precipitation estimates east of the US Continental Divide. The simulation is able to capture the main characteristics of the observed MCSs such as their size, precipitation rate, propagation speed, and lifetime within observational uncertainties. In particular, the model is able to produce realistically propagating MCSs, which was a long-standing challenge in climate modeling. However, the MCS frequency is significantly underestimated in the central US during late summer. We discuss the origin of this frequency biases and suggest strategies for model improvements.

Intellectual property : national and international perspectives.

DOT National Transportation Integrated Search

2009-06-01

A consistent approach to managing intellectual property (IP) permits the effective transfer of the results of research : and encourages the use of products and services by client organizations. This Preliminary Investigation seeks to : capture curren...

On the acquisition and representation of procedural knowledge

NASA Technical Reports Server (NTRS)

Saito, T.; Ortiz, C.; Loftin, R. B.

1992-01-01

Historically knowledge acquisition has proven to be one of the greatest barriers to the development of intelligent systems. Current practice generally requires lengthy interactions between the expert whose knowledge is to be captured and the knowledge engineer whose responsibility is to acquire and represent knowledge in a useful form. Although much research has been devoted to the development of methodologies and computer software to aid in the capture and representation of some of some types of knowledge, little attention has been devoted to procedural knowledge. NASA personnel frequently perform tasks that are primarily procedural in nature. Previous work is reviewed in the field of knowledge acquisition and then focus on knowledge acquisition for procedural tasks with special attention devoted to the Navy's VISTA tool. The design and development is described of a system for the acquisition and representation of procedural knowledge-TARGET (Task Analysis and Rule Generation Tool). TARGET is intended as a tool that permits experts to visually describe procedural tasks and as a common medium for knowledge refinement by the expert and knowledge engineer. The system is designed to represent the acquired knowledge in the form of production rules. Systems such as TARGET have the potential to profoundly reduce the time, difficulties, and costs of developing knowledge-based systems for the performance of procedural tasks.

Coherent Doppler lidar for automated space vehicle rendezvous, stationkeeping and capture

NASA Technical Reports Server (NTRS)

Bilbro, James A.

1991-01-01

The inherent spatial resolution of laser radar makes ladar or lidar an attractive candidate for Automated Rendezvous and Capture application. Previous applications were based on incoherent lidar techniques, requiring retro-reflectors on the target vehicle. Technology improvements (reduced size, no cryogenic cooling requirement) have greatly enhanced the construction of coherent lidar systems. Coherent lidar permits the acquisition of non-cooperative targets at ranges that are limited by the detection capability rather than by the signal-to-noise ratio (SNR) requirements. The sensor can provide translational state information (range, velocity, and angle) by direct measurement and, when used with any array detector, also can provide attitude information by Doppler imaging techniques. Identification of the target is accomplished by scanning with a high pulse repetition frequency (dependent on the SNR). The system performance is independent of range and should not be constrained by sun angle. An initial effort to characterize a multi-element detection system has resulted in a system that is expected to work to a minimum range of 1 meter. The system size, weight and power requirements are dependent on the operating range; 10 km range requires a diameter of 3 centimeters with overall size at 3 x 3 x 15 to 30 cm, while 100 km range requires a 30 cm diameter.

How to optimize radiological images captured from digital cameras, using the Adobe Photoshop 6.0 program.

PubMed

Chalazonitis, A N; Koumarianos, D; Tzovara, J; Chronopoulos, P

2003-06-01

Over the past decade, the technology that permits images to be digitized and the reduction in the cost of digital equipment allows quick digital transfer of any conventional radiological film. Images then can be transferred to a personal computer, and several software programs are available that can manipulate their digital appearance. In this article, the fundamentals of digital imaging are discussed, as well as the wide variety of optional adjustments that the Adobe Photoshop 6.0 (Adobe Systems, San Jose, CA) program can offer to present radiological images with satisfactory digital imaging quality.

Dynamic system classifier.

PubMed

Pumpe, Daniel; Greiner, Maksim; Müller, Ewald; Enßlin, Torsten A

2016-07-01

Stochastic differential equations describe well many physical, biological, and sociological systems, despite the simplification often made in their derivation. Here the usage of simple stochastic differential equations to characterize and classify complex dynamical systems is proposed within a Bayesian framework. To this end, we develop a dynamic system classifier (DSC). The DSC first abstracts training data of a system in terms of time-dependent coefficients of the descriptive stochastic differential equation. Thereby the DSC identifies unique correlation structures within the training data. For definiteness we restrict the presentation of the DSC to oscillation processes with a time-dependent frequency ω(t) and damping factor γ(t). Although real systems might be more complex, this simple oscillator captures many characteristic features. The ω and γ time lines represent the abstract system characterization and permit the construction of efficient signal classifiers. Numerical experiments show that such classifiers perform well even in the low signal-to-noise regime.

76 FR 20004 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-11

... salamander (Ambystoma californiense), the Tipton kangaroo rat (Dipodomys nitratoides nitratoides), giant... biological samples, and release) the California tiger salamander (Ambystoma californiense) in conjunction... (survey, capture, handle, identify, measure, and release) the California tiger salamander (Ambystoma...

TARGET: Rapid Capture of Process Knowledge

NASA Technical Reports Server (NTRS)

Ortiz, C. J.; Ly, H. V.; Saito, T.; Loftin, R. B.

1993-01-01

TARGET (Task Analysis/Rule Generation Tool) represents a new breed of tool that blends graphical process flow modeling capabilities with the function of a top-down reporting facility. Since NASA personnel frequently perform tasks that are primarily procedural in nature, TARGET models mission or task procedures and generates hierarchical reports as part of the process capture and analysis effort. Historically, capturing knowledge has proven to be one of the greatest barriers to the development of intelligent systems. Current practice generally requires lengthy interactions between the expert whose knowledge is to be captured and the knowledge engineer whose responsibility is to acquire and represent the expert's knowledge in a useful form. Although much research has been devoted to the development of methodologies and computer software to aid in the capture and representation of some types of knowledge, procedural knowledge has received relatively little attention. In essence, TARGET is one of the first tools of its kind, commercial or institutional, that is designed to support this type of knowledge capture undertaking. This paper will describe the design and development of TARGET for the acquisition and representation of procedural knowledge. The strategies employed by TARGET to support use by knowledge engineers, subject matter experts, programmers and managers will be discussed. This discussion includes the method by which the tool employs its graphical user interface to generate a task hierarchy report. Next, the approach to generate production rules for incorporation in and development of a CLIPS based expert system will be elaborated. TARGET also permits experts to visually describe procedural tasks as a common medium for knowledge refinement by the expert community and knowledge engineer making knowledge consensus possible. The paper briefly touches on the verification and validation issues facing the CLIPS rule generation aspects of TARGET. A description of efforts to support TARGET's interoperability issues on PCs, Macintoshes and UNIX workstations concludes the paper.

The Clean Water Act and Trash-Free Waters

EPA Pesticide Factsheets

What can we do about trash that has already made it to our streets and waterways? Learn about Clean Water Act tools, trash TMDLs and stormwater permits, as well as information about trash capture and removal technologies.

Cholera Mortality during Urban Epidemic, Dar es Salaam, Tanzania, August 16, 2015–January 16, 20161

PubMed Central

Massay, Amani Elibariki; Narra, Rupa; Mghamba, Janneth; Mohamed, Ahmed Abade; Kishimba, Rogath Saika; Urio, Loveness John; Rusibayamila, Neema; Magembe, Grace; Bakari, Muhammud; Gibson, James J.; Eidex, Rachel Barwick; Quick, Robert E.

2017-01-01

In 2015, a cholera epidemic occurred in Tanzania; most cases and deaths occurred in Dar es Salaam early in the outbreak. We evaluated cholera mortality through passive surveillance, burial permits, and interviews conducted with decedents’ caretakers. Active case finding identified 101 suspected cholera deaths. Routine surveillance had captured only 48 (48%) of all cholera deaths, and burial permit assessments captured the remainder. We interviewed caregivers of 56 decedents to assess cholera management behaviors. Of 51 decedents receiving home care, 5 (10%) used oral rehydration solution after becoming ill. Caregivers reported that 51 (93%) of 55 decedents with known time of death sought care before death; 16 (29%) of 55 delayed seeking care for >6 h. Of the 33 (59%) community decedents, 20 (61%) were said to have been discharged from a health facility before death. Appropriate and early management of cholera cases can reduce the number of cholera deaths. PMID:29155665

Isolation of Circulating Plasma Cells in Multiple Myeloma Using CD138 Antibody-Based Capture in a Microfluidic Device

NASA Astrophysics Data System (ADS)

Qasaimeh, Mohammad A.; Wu, Yichao C.; Bose, Suman; Menachery, Anoop; Talluri, Srikanth; Gonzalez, Gabriel; Fulciniti, Mariateresa; Karp, Jeffrey M.; Prabhala, Rao H.; Karnik, Rohit

2017-04-01

The necessity for bone marrow aspiration and the lack of highly sensitive assays to detect residual disease present challenges for effective management of multiple myeloma (MM), a plasma cell cancer. We show that a microfluidic cell capture based on CD138 antigen, which is highly expressed on plasma cells, permits quantitation of rare circulating plasma cells (CPCs) in blood and subsequent fluorescence-based assays. The microfluidic device is based on a herringbone channel design, and exhibits an estimated cell capture efficiency of ~40-70%, permitting detection of <10 CPCs/mL using 1-mL sample volumes, which is difficult using existing techniques. In bone marrow samples, the microfluidic-based plasma cell counts exhibited excellent correlation with flow cytometry analysis. In peripheral blood samples, the device detected a baseline of 2-5 CD138+ cells/mL in healthy donor blood, with significantly higher numbers in blood samples of MM patients in remission (20-24 CD138+ cells/mL), and yet higher numbers in MM patients exhibiting disease (45-184 CD138+ cells/mL). Analysis of CPCs isolated using the device was consistent with serum immunoglobulin assays that are commonly used in MM diagnostics. These results indicate the potential of CD138-based microfluidic CPC capture as a useful ‘liquid biopsy’ that may complement or partially replace bone marrow aspiration.

Computational and design methods for advanced imaging

NASA Astrophysics Data System (ADS)

Birch, Gabriel C.

This dissertation merges the optical design and computational aspects of imaging systems to create novel devices that solve engineering problems in optical science and attempts to expand the solution space available to the optical designer. This dissertation is divided into two parts: the first discusses a new active illumination depth sensing modality, while the second part discusses a passive illumination system called plenoptic, or lightfield, imaging. The new depth sensing modality introduced in part one is called depth through controlled aberration. This technique illuminates a target with a known, aberrated projected pattern and takes an image using a traditional, unmodified imaging system. Knowing how the added aberration in the projected pattern changes as a function of depth, we are able to quantitatively determine depth of a series of points from the camera. A major advantage this method permits is the ability for illumination and imaging axes to be coincident. Plenoptic cameras capture both spatial and angular data simultaneously. This dissertation present a new set of parameters that permit the design and comparison of plenoptic devices outside the traditionally published plenoptic 1.0 and plenoptic 2.0 configurations. Additionally, a series of engineering advancements are presented, including full system raytraces of raw plenoptic images, Zernike compression techniques of raw image files, and non-uniform lenslet arrays to compensate for plenoptic system aberrations. Finally, a new snapshot imaging spectrometer is proposed based off the plenoptic configuration.

Aerocapture Benefits to Future Science Missions

NASA Technical Reports Server (NTRS)

Artis, Gwen; James, Bonnie

2006-01-01

NASA's In-Space Propulsion Technology (ISPT) Program is investing in technologies to revolutionize the robotic exploration of deep space. One of these technologies is Aerocapture, the most promising of the "aeroassist" techniques used to maneuver a space vehicle within an atmosphere, using aerodynamic forces in lieu of propellant. (Other aeroassist techniques include aeroentry and aerobraking.) Aerocapture relies on drag atmospheric drag to decelerate an incoming spacecraft and capture it into orbit. This technique is very attractive since it permits spacecraft to be launched from Earth at higher velocities, providing shorter trip times and saving mass and overall cost on future missions. Recent aerocapture systems analysis studies quantify the benefits of aerocapture to future exploration. The 2002 Titan aerocapture study showed that using aerocapture at Titan instead of conventional propulsive capture results in over twice as much payload delivered to Titan. Aerocapture at Venus results in almost twice the payload delivered to Venus as with aerobraking, and over six times more mass delivered into orbit than all-propulsive capture. Aerocapture at Mars shows significant benefits as the payload sizes increase and as missions become more complex. Recent Neptune aerocapture studies show that aerocapture opens up entirely new classes of missions at Neptune. Current aerocapture technology development is advancing the maturity of each subsystem technology needed for successful implementation of aerocapture on future missions. Recent development has focused on both rigid aeroshell and inflatable aerocapture systems. Rigid aeroshell systems development includes new ablative and non-ablative thermal protection systems, advanced aeroshell performance sensors, lightweight structures and higher temperature adhesives. Inflatable systems such as trailing tethered and clamped "ballutes" and inflatable aeroshells are also under development. Computational tools required to support future aerocapture missions are an integral part of aerocapture development. Tools include engineering reference atmosphere models, guidance and navigation algorithms, aerothermodynamic modeling, and flight simulation.

Electronic Engineering Notebook: A software environment for research execution, documentation and dissemination

NASA Technical Reports Server (NTRS)

Moerder, Dan

1994-01-01

The electronic engineering notebook (EEN) consists of a free form research notebook, implemented in a commercial package for distributed hypermedia, which includes utilities for graphics capture, formatting and display of LaTex constructs, and interfaces to the host operating system. The latter capability consists of an information computer-aided software engineering (CASE) tool and a means to associate executable scripts with source objects. The EEN runs on Sun and HP workstations. The EEN, in day-to-day use can be used in much the same manner as the sort of research notes most researchers keep during development of projects. Graphics can be pasted in, equations can be entered via LaTex, etc. In addition, the fact that the EEN is hypermedia permits easy management of 'context', e.g., derivations and data can contain easily formed links to other supporting derivations and data. The CASE tool also permits development and maintenance of source code directly in the notebook, with access to its derivations and data.

PolyMetformin combines carrier and anticancer activities for in vivo siRNA delivery.

PubMed

Zhao, Yi; Wang, Wei; Guo, Shutao; Wang, Yuhua; Miao, Lei; Xiong, Yang; Huang, Leaf

2016-06-06

Metformin, a widely implemented anti-diabetic drug, exhibits potent anticancer efficacies. Herein a polymeric construction of Metformin, PolyMetformin (PolyMet) is successfully synthesized through conjugation of linear polyethylenimine (PEI) with dicyandiamide. The delocalization of cationic charges in the biguanide groups of PolyMet reduces the toxicity of PEI both in vitro and in vivo. Furthermore, the polycationic properties of PolyMet permits capture of siRNA into a core-membrane structured lipid-polycation-hyaluronic acid (LPH) nanoparticle for systemic gene delivery. Advances herein permit LPH-PolyMet nanoparticles to facilitate VEGF siRNA delivery for VEGF knockdown in a human lung cancer xenograft, leading to enhanced tumour suppressive efficacy. Even in the absence of RNAi, LPH-PolyMet nanoparticles act similarly to Metformin and induce antitumour efficacy through activation of the AMPK and inhibition of the mTOR. In essence, PolyMet successfully combines the intrinsic anticancer efficacy of Metformin with the capacity to carry siRNA to enhance the therapeutic activity of an anticancer gene therapy.

75 FR 31812 - Receipt of Applications for Endangered Species Permits

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-04

..., and release of eastern indigo snake (Drymarchon corais couperi), reticulated flatwoods salamander (Ambystoma bishopi), and frosted flatwoods salamander (Ambystoma cingulatum) in Georgia. Applicant: Jess... authorization to: Capture and release eastern indigo snake, frosted flatwood salamander, reticulated flatwoods...

Metamodels for Ozone - Comparison of Two Techniques

EPA Science Inventory

A metamodel is a mathematical relationship between the inputs and outputs of a simulation experiment, permitting calculation of outputs for scenarios of interest without having to run new (presumably costly) experiments. Ozone metamodels are typically designed to capture a parti...

Enrichment of cancer cells using aptamers immobilized on a microfluidic channel

PubMed Central

Phillips, Joseph A.; Xu, Ye; Xia, Zheng

2009-01-01

This work describes the development and investigation of an aptamer modified microfluidic device that captures rare cells to achieve a rapid assay without pre-treatment of cells. To accomplish this, aptamers are first immobilized on the surface of a poly (dimethylsiloxane) microchannel, followed by pumping a mixture of cells through the device. This process permits the use of optical microscopy to measure the cell-surface density from which we calculate the percentage of cells captured as a function of cell and aptamer concentration, flow velocity, and incubation time. This aptamer-based device was demonstrated to capture target cells with > 97% purity and > 80% efficiency. Since the cell capture assay is completed within minutes and requires no pre-treatment of cells, the device promises to play a key role in the early detection and diagnosis of cancer where rare diseased cells can first be enriched and then captured for detection. PMID:19115856

Compact, Lightweight Adsorber and Sabatier Reactor for CO2 Capture and Reduction for Consumable and Propellant Production

NASA Technical Reports Server (NTRS)

Junaedi, Christian; Hawley, Kyle; Walsh, Dennis; Roychoudhury, Subir; Busby, Stacy A.; Abney, Morgan B.; Perry, Jay L.; Knox, James C.

2012-01-01

The utilization of CO2 to produce (or recycle) life support consumables, such as O2 and H2O, and to generate propellant fuels is an important aspect of NASA's concept for future, long duration planetary exploration. One potential approach is to capture and use CO2 from the Martian atmosphere to generate the consumables and propellant fuels. Precision Combustion, Inc. (PCI), with support from NASA, continues to develop its regenerable adsorber technology for capturing CO2 from gaseous atmospheres (for cabin atmosphere revitalization and in-situ resource utilization applications) and its Sabatier reactor for converting CO2 to methane and water. Both technologies are based on PCI's Microlith(R) substrates and have been demonstrated to reduce size, weight, and power consumption during CO2 capture and methanation process. For adsorber applications, the Microlith substrates offer a unique resistive heating capability that shows potential for short regeneration time and reduced power requirements compared to conventional systems. For the Sabatier applications, the combination of the Microlith substrates and durable catalyst coating permits efficient CO2 methanation that favors high reactant conversion, high selectivity, and durability. Results from performance testing at various operating conditions will be presented. An effort to optimize the Sabatier reactor and to develop a bench-top Sabatier Development Unit (SDU) will be discussed.

A High-Order, Linear Time-Invariant Model for Application to Higher Harmonic Control and Flight Control System Interaction

NASA Technical Reports Server (NTRS)

Cheng, Rendy P.; Tischler, Mark B.; Celi, Roberto

2006-01-01

This research describes a new methodology for the extraction of a high-order, linear time invariant model, which allows the periodicity of the helicopter response to be accurately captured. This model provides the needed level of dynamic fidelity to permit an analysis and optimization of the AFCS and HHC algorithms. The key results of this study indicate that the closed-loop HHC system has little influence on the AFCS or on the vehicle handling qualities, which indicates that the AFCS does not need modification to work with the HHC system. However, the results show that the vibration response to maneuvers must be considered during the HHC design process, and this leads to much higher required HHC loop crossover frequencies. This research also demonstrates that the transient vibration responses during maneuvers can be reduced by optimizing the closed-loop higher harmonic control algorithm using conventional control system analyses.

3D papillary image capturing by the stereo fundus camera system for clinical diagnosis on retina and optic nerve

NASA Astrophysics Data System (ADS)

Motta, Danilo A.; Serillo, André; de Matos, Luciana; Yasuoka, Fatima M. M.; Bagnato, Vanderlei S.; Carvalho, Luis A. V.

2014-03-01

Glaucoma is the second main cause of the blindness in the world and there is a tendency to increase this number due to the lifetime expectation raise of the population. Glaucoma is related to the eye conditions, which leads the damage to the optic nerve. This nerve carries visual information from eye to brain, then, if it has damage, it compromises the visual quality of the patient. In the majority cases the damage of the optic nerve is irreversible and it happens due to increase of intraocular pressure. One of main challenge for the diagnosis is to find out this disease, because any symptoms are not present in the initial stage. When is detected, it is already in the advanced stage. Currently the evaluation of the optic disc is made by sophisticated fundus camera, which is inaccessible for the majority of Brazilian population. The purpose of this project is to develop a specific fundus camera without fluorescein angiography and red-free system to accomplish 3D image of optic disc region. The innovation is the new simplified design of a stereo-optical system, in order to make capable the 3D image capture and in the same time quantitative measurements of excavation and topography of optic nerve; something the traditional fundus cameras do not do. The dedicated hardware and software is developed for this ophthalmic instrument, in order to permit quick capture and print of high resolution 3D image and videos of optic disc region (20° field-of-view) in the mydriatic and nonmydriatic mode.

The Emergency Alternative Arrangement Exception to the National Environmental Policy Act: What Constitutes an Emergency? Should the Navy Pin Its Hopes on Noah Webster?

DTIC Science & Technology

2009-08-31

granted for discharging pumped water into Lake Pontchartrain without a NPDES permit under the CW A, for depositing into wetlands without a CW A 404...484. 116 32 c.F.R. § 989.34(b) (2009). 1171d. 118 Colonel E.G. Willard, Lieutenant Colonel Tom Zimmerman, and Lieutenant Colonel Eric Bee ...Service in December 1985 issued a permit authorizing the capture and removal of all six surviving wild California condors. 177 This was a change in their

75 FR 22835 - Endangered and Threatened Wildlife and Plants; Permits, Santa Cruz County, CA

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-30

... defined under the Act as ``to harass, harm, pursue, hunt, shoot, wound, kill, trap, capture, or collect... would then implement the HCP. Construction of a pump house and pipeline for the Ma[ntilde]ana Woods HCP...

HOT CELL SYSTEM FOR DETERMINING FISSION GAS RETENTION IN METALLIC FUELS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sell, D. A.; Baily, C. E.; Malewitz, T. J.

2016-09-01

A system has been developed to perform measurements on irradiated, sodium bonded-metallic fuel elements to determine the amount of fission gas retained in the fuel material after release of the gas to the element plenum. During irradiation of metallic fuel elements, most of the fission gas developed is released from the fuel and captured in the gas plenums of the fuel elements. A significant amount of fission gas, however, remains captured in closed porosities which develop in the fuel during irradiation. Additionally, some gas is trapped in open porosity but sealed off from the plenum by frozen bond sodium aftermore » the element has cooled in the hot cell. The Retained fission Gas (RFG) system has been designed, tested and implemented to capture and measure the quantity of retained fission gas in characterized cut pieces of sodium bonded metallic fuel. Fuel pieces are loaded into the apparatus along with a prescribed amount of iron powder, which is used to create a relatively low melting, eutectic composition as the iron diffuses into the fuel. The apparatus is sealed, evacuated, and then heated to temperatures in excess of the eutectic melting point. Retained fission gas release is monitored by pressure transducers during the heating phase, thus monitoring for release of fission gas as first the bond sodium melts and then the fuel. A separate hot cell system is used to sample the gas in the apparatus and also characterize the volume of the apparatus thus permitting the calculation of the total fission gas release from the fuel element samples along with analysis of the gas composition.« less

Active CO2 Reservoir Management for Carbon Capture, Utilization, and Sequestration: Impact on Permitting, Monitoring, and Public Acceptance

NASA Astrophysics Data System (ADS)

Buscheck, T. A.; Chen, M.; Sun, Y.; Hao, Y.; Court, B.; Celia, M. A.; Wolery, T.; Aines, R. D.

2011-12-01

CO2 capture and sequestration (CCS) integrated with geothermal energy production in deep geological formations can play an important role in reducing CO2 emissions to the atmosphere and thereby mitigate global climate change. For industrial-scale CO2 injection in saline formations, pressure buildup can limit storage capacity and security. Active CO2 Reservoir Management (ACRM) combines brine production with CO2 injection to relieve pressure buildup, increase injectivity, manipulate CO2 migration, constrain brine leakage, and enable beneficial utilization of produced brine. Therefore, ACRM can be an enabler of carbon capture, utilization, and sequestration (CCUS). Useful products may include freshwater, cooling water, make-up water for pressure support in oil, gas, and geothermal reservoir operations, and geothermal energy production. Implementation barriers to industrial-scale CCS include concerns about (1) CO2 sequestration security and assurance, (2) pore-space competition with neighboring subsurface activities, (3) CO2 capture costs, and (4) water-use demands imposed by CCS operations, which is particularly important where water resources are already scarce. CCUS, enabled by ACRM, has the potential of addressing these barriers. Pressure relief from brine production can substantially reduce the driving force for potential CO2 and brine migration, as well as minimize interference with neighboring subsurface activities. Electricity generated from geothermal energy can offset a portion of the parasitic energy and financial costs of CCS. Produced brine can be used to generate freshwater by desalination technologies, such as RO, provide a source for saltwater cooling systems or be used as make-up water for oil, gas, or geothermal reservoir operations, reducing the consumption of valuable freshwater resources. We examine the impact of brine production on reducing CO2 and brine leakage. A volumetric balance between injected and produced fluids minimizes the spatial extent of the pressure perturbation, substantially reducing both the Area of Review (AoR) and interactions with neighboring subsurface activities. This will reduce pore-space competition between neighboring subsurface activities, allowing for independent planning, assessment, and permitting. Because post-injection pressure buildup is virtually eliminated, this could have a major impact on post-injection monitoring requirements. Reducing the volume of rock over which brine can migrate may significantly affect site characterization requirements, as well as the impact of parametric and conceptual model uncertainties, such as those related to abandoned wells. ACRM-CCUS has the potential of playing a beneficial role in site-characterization, permitting, and monitoring activities, and in gaining public acceptance. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Considering the Lives of Microbes in Microbial Communities.

PubMed

Shank, Elizabeth A

2018-01-01

Over the last decades, sequencing technologies have transformed our ability to investigate the composition and functional capacity of microbial communities. Even so, critical questions remain about these complex systems that cannot be addressed by the bulk, community-averaged data typically provided by sequencing methods. In this Perspective, I propose that future advances in microbiome research will emerge from considering "the lives of microbes": we need to create methods to explicitly interrogate how microbes exist and interact in native-setting-like microenvironments. This approach includes developing approaches that expose the phenotypic heterogeneity of microbes; exploring the effects of coculture cues on cellular differentiation and metabolite production; and designing visualization systems that capture features of native microbial environments while permitting the nondestructive observation of microbial interactions over space and time with single-cell resolution.

77 FR 30508 - Marine Mammals; File No. 16991

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... Road, Moss Landing, California 95039 to conduct research on harbor seals (Phoca vitulina). ADDRESSES... seals had been submitted by the above-named applicant. The requested permit has been issued under the... harassment and capture of harbor seals in California, Oregon, Washington, and Alaska. Harassment is...

77 FR 26747 - Marine Mammals; File No. 15748

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-07

... Scientific Research Permit No. 15748. DATES: Written, telefaxed, or email comments must be received on or... shore of Ross Island, Antarctica to study thermoregulation. The research involves capture and restraint of adult females and pups/juveniles of either sex for attachment of scientific instruments...

78 FR 27249 - Endangered Species Recovery Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-09

... samples, and release) the California tiger salamander (Santa Barbara County DPS and Sonoma County DPS... renewal to take (harass by survey, capture, handle, mark, and release) the California tiger salamander..., mark, release, and collect) the Santa Cruz long-toed salamander (Ambystoma macrodactylum croceum), in...

FIELD TESTING AND EVALUATION OF ZERPOL® AT PIONEER METAL FINISHING

EPA Science Inventory

The project examines the Zerpol® process. The Zerpol® process, as used in metal plating operations, captures all aqueous effluent from the manufacturing operations, conditions the effluent to remove any metal or cyanide that may be present, and permits the reuse of the ...

On the use of secondary capture-recapture samples to estimate temporary emigration and breeding proportions

USGS Publications Warehouse

Kendall, W.L.; Nichols, J.D.; North, P.M.; Nichols, J.D.

1995-01-01

The use of the Cormack- Jolly-Seber model under a standard sampling scheme of one sample per time period, when the Jolly-Seber assumption that all emigration is permanent does not hold, leads to the confounding of temporary emigration probabilities with capture probabilities. This biases the estimates of capture probability when temporary emigration is a completely random process, and both capture and survival probabilities when there is a temporary trap response in temporary emigration, or it is Markovian. The use of secondary capture samples over a shorter interval within each period, during which the population is assumed to be closed (Pollock's robust design), provides a second source of information on capture probabilities. This solves the confounding problem, and thus temporary emigration probabilities can be estimated. This process can be accomplished in an ad hoc fashion for completely random temporary emigration and to some extent in the temporary trap response case, but modelling the complete sampling process provides more flexibility and permits direct estimation of variances. For the case of Markovian temporary emigration, a full likelihood is required.

Margins of safety provided by COSHH Essentials and the ILO Chemical Control Toolkit.

PubMed

Jones, Rachael M; Nicas, Mark

2006-03-01

COSHH Essentials, developed by the UK Health and Safety Executive, and the Chemical Control Toolkit (Toolkit) proposed by the International Labor Organization, are 'control banding' approaches to workplace risk management intended for use by proprietors of small and medium-sized businesses. Both systems group chemical substances into hazard bands based on toxicological endpoint and potency. COSSH Essentials uses the European Union's Risk-phrases (R-phrases), whereas the Toolkit uses R-phrases and the Globally Harmonized System (GHS) of Classification and Labeling of Chemicals. Each hazard band is associated with a range of airborne concentrations, termed exposure bands, which are to be attained by the implementation of recommended control technologies. Here we analyze the margin of safety afforded by the systems and, for each hazard band, define the minimal margin as the ratio of the minimum airborne concentration that produced the toxicological endpoint of interest in experimental animals to the maximum concentration in workplace air permitted by the exposure band. We found that the minimal margins were always <100, with some ranging to <1, and inversely related to molecular weight. The Toolkit-GHS system generally produced margins equal to or larger than COSHH Essentials, suggesting that the Toolkit-GHS system is more protective of worker health. Although, these systems predict exposures comparable with current occupational exposure limits, we argue that the minimal margins are better indicators of health protection. Further, given the small margins observed, we feel it is important that revisions of these systems provide the exposure bands to users, so as to permit evaluation of control technology capture efficiency.

Aerocapture Technology to Reduce Trip Time and Cost of Planetary Missions

NASA Astrophysics Data System (ADS)

Artis, Gwen R.; James, B.

2006-12-01

NASA’s In-Space Propulsion Technology (ISPT) Program is investing in technologies to revolutionize the robotic exploration of deep space. One of these technologies is Aerocapture, the most promising of the “aeroassist” techniques used to maneuver a space vehicle within an atmosphere, using aerodynamic forces in lieu of propellant. (Other aeroassist techniques include aeroentry and aerobraking.) Aerocapture relies on drag atmospheric drag to decelerate an incoming spacecraft and capture it into orbit. This technique is very attractive since it permits spacecraft to be launched from Earth at higher velocities, providing shorter trip times and saving mass and overall cost on future missions. Recent aerocapture systems analysis studies quantify the benefits of aerocapture to future exploration. The 2002 Titan aerocapture study showed that using aerocapture at Titan instead of conventional propulsive capture results in over twice as much payload delivered to Titan. Aerocapture at Venus results in almost twice the payload delivered to Venus as with aerobraking, and over six times more mass delivered into orbit than all-propulsive capture. Aerocapture at Mars shows significant benefits as the payload sizes increase and as missions become more complex. Recent Neptune aerocapture studies show that aerocapture opens up entirely new classes of missions at Neptune. Current aerocapture technology development is advancing the maturity of each sub-system technology needed for successful implementation of aerocapture on future missions. Recent development has focused on both rigid aeroshell and inflatable aerocapture systems. Rigid aeroshell systems development includes new ablative and non-ablative thermal protection systems, advanced aeroshell performance sensors, lightweight structures and higher temperature adhesives. Inflatable systems such as trailing tethered and clamped “ballutes” and inflatable aeroshells are also under development. Computational tools required to support future aerocapture missions are an integral part of aerocapture development. Tools include engineering reference atmosphere models, guidance and navigation algorithms, aerothermodynamic modeling, and flight simulation.

When attempts at robbing prey turn fatal

NASA Astrophysics Data System (ADS)

Dejean, Alain; Corbara, Bruno; Azémar, Frédéric; Carpenter, James M.

2012-07-01

Because group-hunting arboreal ants spread-eagle insect prey for a long time before retrieving them, these prey can be coveted by predatory flying insects. Yet, attempting to rob these prey is risky if the ant species is also an effective predator. Here, we show that trying to rob prey from Azteca andreae workers is a fatal error as 268 out of 276 potential cleptobionts (97.1 %) were captured in turn. The ant workers hunt in a group and use the "Velcro®" principle to cling firmly to the leaves of their host tree, permitting them to capture very large prey. Exceptions were one social wasp, plus some Trigona spp. workers and flies that landed directly on the prey and were able to take off immediately when attacked. We conclude that in this situation, previously captured prey attract potential cleptobionts that are captured in turn in most of the cases.

The Lunar IceCube Mission Design: Construction of Feasible Transfer Trajectories with a Constrained Departure

NASA Technical Reports Server (NTRS)

Folta, David C.; Bosanac, Natasha; Cox, Andrew; Howell, Kathleen C.

2016-01-01

Lunar IceCube, a 6U CubeSat, will prospect for water and other volatiles from a low-periapsis, highly inclined elliptical lunar orbit. Injected from Exploration Mission-1, a lunar gravity assisted multi-body transfer trajectory will capture into a lunar science orbit. The constrained departure asymptote and value of trans-lunar energy limit transfer trajectory types that re-encounter the Moon with the necessary energy and flight duration. Purdue University and Goddard Space Flight Center's Adaptive Trajectory Design tool and dynamical system research is applied to uncover cislunar spatial regions permitting viable transfer arcs. Numerically integrated transfer designs applying low-thrust and a design framework are described.

78 FR 60918 - Notice of Permit Applications Received Under the Antarctic Conservation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-02

... commercially available, bacteria supplement for municipal Wastewater Treatment Plants, to be used in the... enzymatic substrate, nutrient base and bacteria for the treatment process. Bacteria would not be released to the marine environment. Most of the bacteria are eventually captured in the wastewater treatment plant...

77 FR 38587 - Marine Mammals; File No. 14325

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-28

... appointment in the following offices: Permits and Conservation Division, Office of Protected Resources, NMFS... restraint of pups in the eastern Distinct Population Segment (eDPS) and western DPS (wDPS); capture of adult... have a significant adverse impact on the human environment. As required by the ESA, issuance of this...

76 FR 78890 - Endangered Species; File No. 15566

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-20

... coriacea), and 1 hawksbill (Eretmochelys imbricata) sea turtle in order to assess temporal change in catch rates, size distributions, sex and genetic ratios, and health of sea turtles. Captures occur annually in... PIT tagged, photographed, and released. No other changes would be made to the permit. The purpose of...

Captures of boll weevils (Coleoptera: Curculionidae) in relation to trap distance from cotton fields

USDA-ARS?s Scientific Manuscript database

Once populations of the boll weevil (Anthonomus grandis grandis Boheman) are suppressed, eradication programs rely on pheromone trap-based monitoring for timely detection of weevil populations in cotton (Gossypium spp.). Delayed detection may increase the costs of remedial treatments, and permit rep...

75 FR 24966 - Endangered and Threatened Wildlife and Plants; Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-06

...: TE010887A. Applicant: U.S. Geological Survey, Great Lakes Science Center, Porter, Indiana. The applicant... involve capture of adult butterflies for captive rearing, experimental treatments on captive-reared larvae... conducting survey and assessment work. Activities are for the enhancement of survival of the species in the...

75 FR 33578 - Endangered Species; File Nos. 14508 and 14655

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-14

... (Lepidochelys kempii) sea turtles for purposes of scientific research. ADDRESSES: The permit and related... abundance, genetic origin and feeding ecology of sea turtles using Lake Worth Lagoon in Palm Beach County, Florida. Up to 50 green, 5 loggerhead, 2 hawksbill, and 1 Kemp's ridley sea turtles may be captured...

75 FR 2106 - Endangered and Threatened Species; Take of Anadromous Fish

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-14

... and Threatened Species; Take of Anadromous Fish AGENCY: National Marine Fisheries Service (NMFS... NMFS regulations (50 CFR parts 222-226) governing listed fish and wildlife permits. Species Covered in... steelhead not to exceed 2 percent of the total number of fish captured for each life stage and species...

75 FR 11132 - Marine Mammals; File No. 555-1870

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-10

... appointment in the following offices: Permits, Conservation and Education Division, Office of Protected... capture, sedation, tagging, and sampling from 40 seals (20 males and 20 females) to 70 seals (35 males and 35 females). The request to bring up to six seals into temporary captivity for a pilot study to...

75 FR 54093 - Marine Mammals; File No. 555-1870

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-03

... appointment in the following offices: Permits, Conservation and Education Division, Office of Protected... annually in California by capture, sedation, tagging, and sampling from 40 seals (20 males and 20 females) to 70 seals (35 males and 35 females). Also, a pilot study is authorized to bring up to six seals...

Human Activity Recognition in AAL Environments Using Random Projections.

PubMed

Damaševičius, Robertas; Vasiljevas, Mindaugas; Šalkevičius, Justas; Woźniak, Marcin

2016-01-01

Automatic human activity recognition systems aim to capture the state of the user and its environment by exploiting heterogeneous sensors attached to the subject's body and permit continuous monitoring of numerous physiological signals reflecting the state of human actions. Successful identification of human activities can be immensely useful in healthcare applications for Ambient Assisted Living (AAL), for automatic and intelligent activity monitoring systems developed for elderly and disabled people. In this paper, we propose the method for activity recognition and subject identification based on random projections from high-dimensional feature space to low-dimensional projection space, where the classes are separated using the Jaccard distance between probability density functions of projected data. Two HAR domain tasks are considered: activity identification and subject identification. The experimental results using the proposed method with Human Activity Dataset (HAD) data are presented.

Human Activity Recognition in AAL Environments Using Random Projections

PubMed Central

Damaševičius, Robertas; Vasiljevas, Mindaugas; Šalkevičius, Justas; Woźniak, Marcin

2016-01-01

Automatic human activity recognition systems aim to capture the state of the user and its environment by exploiting heterogeneous sensors attached to the subject's body and permit continuous monitoring of numerous physiological signals reflecting the state of human actions. Successful identification of human activities can be immensely useful in healthcare applications for Ambient Assisted Living (AAL), for automatic and intelligent activity monitoring systems developed for elderly and disabled people. In this paper, we propose the method for activity recognition and subject identification based on random projections from high-dimensional feature space to low-dimensional projection space, where the classes are separated using the Jaccard distance between probability density functions of projected data. Two HAR domain tasks are considered: activity identification and subject identification. The experimental results using the proposed method with Human Activity Dataset (HAD) data are presented. PMID:27413392

Tandem mass spectrometry of human tryptic blood peptides calculated by a statistical algorithm and captured by a relational database with exploration by a general statistical analysis system.

PubMed

Bowden, Peter; Beavis, Ron; Marshall, John

2009-11-02

A goodness of fit test may be used to assign tandem mass spectra of peptides to amino acid sequences and to directly calculate the expected probability of mis-identification. The product of the peptide expectation values directly yields the probability that the parent protein has been mis-identified. A relational database could capture the mass spectral data, the best fit results, and permit subsequent calculations by a general statistical analysis system. The many files of the Hupo blood protein data correlated by X!TANDEM against the proteins of ENSEMBL were collected into a relational database. A redundant set of 247,077 proteins and peptides were correlated by X!TANDEM, and that was collapsed to a set of 34,956 peptides from 13,379 distinct proteins. About 6875 distinct proteins were only represented by a single distinct peptide, 2866 proteins showed 2 distinct peptides, and 3454 proteins showed at least three distinct peptides by X!TANDEM. More than 99% of the peptides were associated with proteins that had cumulative expectation values, i.e. probability of false positive identification, of one in one hundred or less. The distribution of peptides per protein from X!TANDEM was significantly different than those expected from random assignment of peptides.

Goal-Based Domain Modeling as a Basis for Cross-Disciplinary Systems Engineering

NASA Astrophysics Data System (ADS)

Jarke, Matthias; Nissen, Hans W.; Rose, Thomas; Schmitz, Dominik

Small and medium-sized enterprises (SMEs) are important drivers for innovation. In particular, project-driven SMEs that closely cooperate with their customers have specific needs in regard to information engineering of their development process. They need a fast requirements capture since this is most often included in the (unpaid) offer development phase. At the same time, they need to maintain and reuse the knowledge and experiences they have gathered in previous projects extensively as it is their core asset. The situation is complicated further if the application field crosses disciplinary boundaries. To bridge the gaps and perspectives, we focus on shared goals and dependencies captured in models at a conceptual level. Such a model-based approach also offers a smarter connection to subsequent development stages, including a high share of automated code generation. In the approach presented here, the agent- and goal-oriented formalism i * is therefore extended by domain models to facilitate information organization. This extension permits a domain model-based similarity search, and a model-based transformation towards subsequent development stages. Our approach also addresses the evolution of domain models reflecting the experiences from completed projects. The approach is illustrated with a case study on software-intensive control systems in an SME of the automotive domain.

Self-sustaining turbulence in a restricted nonlinear model of plane Couette flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Vaughan L.; Gayme, Dennice F.; Lieu, Binh K.

2014-10-15

This paper demonstrates the maintenance of self-sustaining turbulence in a restricted nonlinear (RNL) model of plane Couette flow. The RNL system is derived directly from the Navier-Stokes equations and permits higher resolution studies of the dynamical system associated with the stochastic structural stability theory (S3T) model, which is a second order approximation of the statistical state dynamics of the flow. The RNL model shares the dynamical restrictions of the S3T model but can be easily implemented by reducing a DNS code so that it retains only the RNL dynamics. Comparisons of turbulence arising from DNS and RNL simulations demonstrate thatmore » the RNL system supports self-sustaining turbulence with a mean flow as well as structural and dynamical features that are consistent with DNS. These results demonstrate that the simplified RNL system captures fundamental aspects of fully developed turbulence in wall-bounded shear flows and motivate use of the RNL/S3T framework for further study of wall-turbulence.« less

Real-time interactive projection system based on infrared structured-light method

NASA Astrophysics Data System (ADS)

Qiao, Xiaorui; Zhou, Qian; Ni, Kai; He, Liang; Wu, Guanhao; Mao, Leshan; Cheng, Xuemin; Ma, Jianshe

2012-11-01

Interactive technologies have been greatly developed in recent years, especially in projection field. However, at present, most interactive projection systems are based on special designed interactive pens or whiteboards, which is inconvenient and limits the improvement of user experience. In this paper, we introduced our recent progress on theoretically modeling a real-time interactive projection system. The system permits the user to easily operate or draw on the projection screen directly by fingers without any other auxiliary equipment. The projector projects infrared striping patterns onto the screen and the CCD captures the deformational image. We resolve the finger's position and track its movement by processing the deformational image in real-time. A new way to determine whether the finger touches the screen is proposed. The first deformational fringe on the fingertip and the first fringe at the finger shadow are the same one. The correspondence is obtained, so the location parameters can be decided by triangulation. The simulation results are given, and errors are analyzed.

77 FR 22278 - Eagle Permits; Revisions to Regulations Governing Take Necessary To Protect Interests in...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-13

... mortalities caused by collisions with rotating wind turbines. Since publication of the 2009 final rule, the... more information. FOR FURTHER INFORMATION CONTACT: Chief, Division of Migratory Bird Management, at 703... following broad range of actions: ``pursue, shoot, shoot at, poison, wound, kill, capture, trap, collect...

A single-sampling hair trap for mesocarnivores

Treesearch

Jonathan N. Pauli; Matthew B. Hamilton; Edward B. Crain; Steven W. Buskirk

2007-01-01

Although techniques to analyze and quantifY DNA-based data have progressed, methods to noninvasively collect samples lag behind. Samples are generally collected from devices that permit coincident sampling of multiple individuals. Because of cross-contamination, substantive genotyping errors can arise. We developed a cost-effective (US$4.60/trap) single-capture hair...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2011 CFR

2011-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR § 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2013 CFR

2013-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2014 CFR

2014-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2012 CFR

2012-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2010 CFR

2010-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

75 FR 9248 - Endangered and Threatened Wildlife and Plants; Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-01

... endangered species in the Code of Federal Regulations (CFR) at 50 CFR 17. Submit your written data, comments... renewal to take (capture and release) Indiana bats, gray bats, and Virginia big-eared bats (Corynorhinus... and release) Indiana bats, gray bats, Virginia big-eared bats, Ozark big-eared bats (Corynorhinus...

77 FR 24466 - Endangered and Threatened Species; Take of Anadromous Fish

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-24

... is hereby given that NMFS has received 15 scientific research permit application requests relating to... anesthetized to limit stress) and released. The IDEQ does not intend to kill any of the fish being captured... widely throughout the Salmon River subbasin. The work will benefit fish by giving managers key...

77 FR 14734 - Incidental Take Permit and Habitat Conservation Plan for PacifiCorp Klamath Hydroelectric Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-13

... (Oncorhynchus kisutch) as a result of operation and maintenance of its Klamath Hydroelectric Project (Project... term ``take'' as: ``harass, harm, pursue, hunt, shoot, wound, kill, trap, capture, or collect, or to... the East Side and West Side canals, penstocks, turbines, and powerhouse facilities, (3) Operate and...

Capture of endothelial cells under flow using immobilized vascular endothelial growth factor

PubMed Central

Smith, Randall J.; Koobatian, Maxwell T.; Shahini, Aref; Swartz, Daniel D.; Andreadis, Stelios T.

2015-01-01

We demonstrate the ability of immobilized vascular endothelial growth factor (VEGF) to capture endothelial cells (EC) with high specificity under fluid flow. To this end, we engineered a surface consisting of heparin bound to poly-L-lysine to permit immobilization of VEGF through the C-terminal heparin-binding domain. The immobilized growth factor retained its biological activity as shown by proliferation of EC and prolonged activation of KDR signaling. Using a microfluidic device we assessed the ability to capture EC under a range of shear stresses from low (0.5 dyne/cm2) to physiological (15 dyne/cm2). Capture was significant for all shear stresses tested. Immobilized VEGF was highly selective for EC as evidenced by significant capture of human umbilical vein and ovine pulmonary artery EC but no capture of human dermal fibroblasts, human hair follicle derived mesenchymal stem cells, or mouse fibroblasts. Further, VEGF could capture EC from mixtures with non-EC under low and high shear conditions as well as from complex fluids like whole human blood under high shear. Our findings may have far reaching implications, as they suggest that VEGF could be used to promote endothelialization of vascular grafts or neovascularization of implanted tissues by rare but continuously circulating EC. PMID:25771020

Mountain front migration and drainage captures related to fault segment linkage and growth: The Polopos transpressive fault zone (southeastern Betics, SE Spain)

NASA Astrophysics Data System (ADS)

Giaconia, Flavio; Booth-Rea, Guillermo; Martínez-Martínez, José Miguel; Azañón, José Miguel; Pérez-Romero, Joaquín; Villegas, Irene

2013-01-01

The Polopos E-W- to ESE-WNW-oriented dextral-reverse fault zone is formed by the North Alhamilla reverse fault and the North and South Gafarillos dextral faults. It is a conjugate fault system of the sinistral NNE-SSW Palomares fault zone, active from the late most Tortonian (≈7 Ma) up to the late Pleistocene (≥70 ky) in the southeastern Betics. The helicoidal geometry of the fault zone permits to shift SE-directed movement along the South Cabrera reverse fault to NW-directed shortening along the North Alhamilla reverse fault via vertical Gafarillos fault segments, in between. Since the Messinian, fault activity migrated southwards forming the South Gafarillos fault and displacing the active fault-related mountain-front from the north to the south of Sierra de Polopos; whilst recent activity of the North Alhamilla reverse fault migrated westwards. The Polopos fault zone determined the differential uplift between the Sierra Alhamilla and the Tabernas-Sorbas basin promoting the middle Pleistocene capture that occurred in the southern margin of the Sorbas basin. Continued tectonic uplift of the Sierra Alhamilla-Polopos and Cabrera anticlinoria and local subsidence associated to the Palomares fault zone in the Vera basin promoted the headward erosion of the Aguas river drainage that captured the Sorbas basin during the late Pleistocene.

Evolution of a Patient Information Management System in a Local Area Network Environment at Loyola University of Chicago Medical Center

PubMed Central

Price, Ronald N; Chandrasekhar, Arcot J; Tamirisa, Balaji

1990-01-01

The Department of Medicine at Loyola University Medical Center (LUMC) of Chicago has implemented a local area network (LAN) based Patient Information Management System (PIMS) as part of its integrated departmental database management system. PIMS consists of related database applications encompassing demographic information, current medications, problem lists, clinical data, prior events, and on-line procedure results. Integration into the existing departmental database system permits PIMS to capture and manipulate data in other departmental applications. Standardization of clinical data is accomplished through three data tables that verify diagnosis codes, procedures codes and a standardized set of clinical data elements. The modularity of the system, coupled with standardized data formats, allowed the development of a Patient Information Protocol System (PIPS). PIPS, a userdefinable protocol processor, provides physicians with individualized data entry or review screens customized for their specific research protocols or practice habits. Physician feedback indicates that the PIMS/PIPS combination enhances their ability to collect and review specific patient information by filtering large amount of clinical data.

Tools for knowledge acquisition within the NeuroScholar system and their application to anatomical tract-tracing data

PubMed Central

Burns, Gully APC; Cheng, Wei-Cheng

2006-01-01

Background Knowledge bases that summarize the published literature provide useful online references for specific areas of systems-level biology that are not otherwise supported by large-scale databases. In the field of neuroanatomy, groups of small focused teams have constructed medium size knowledge bases to summarize the literature describing tract-tracing experiments in several species. Despite years of collation and curation, these databases only provide partial coverage of the available published literature. Given that the scientists reading these papers must all generate the interpretations that would normally be entered into such a system, we attempt here to provide general-purpose annotation tools to make it easy for members of the community to contribute to the task of data collation. Results In this paper, we describe an open-source, freely available knowledge management system called 'NeuroScholar' that allows straightforward structured markup of the PDF files according to a well-designed schema to capture the essential details of this class of experiment. Although, the example worked through in this paper is quite specific to neuroanatomical connectivity, the design is freely extensible and could conceivably be used to construct local knowledge bases for other experiment types. Knowledge representations of the experiment are also directly linked to the contributing textual fragments from the original research article. Through the use of this system, not only could members of the community contribute to the collation task, but input data can be gathered for automated approaches to permit knowledge acquisition through the use of Natural Language Processing (NLP). Conclusion We present a functional, working tool to permit users to populate knowledge bases for neuroanatomical connectivity data from the literature through the use of structured questionnaires. This system is open-source, fully functional and available for download from [1]. PMID:16895608

Penetration of multiple thin films in micrometeorite capture cells

NASA Technical Reports Server (NTRS)

Simon, Charles G.

1994-01-01

As part of a continuing effort to develop cosmic dust detectors/collectors for use in space, we performed a series of hypervelocity impact experiments on combined sensor/capture-cell assemblies using 10-200-micron-diameter glass projectiles and olivine crystals at velocities of 0.9-14.4 km/s. The design objective of the space-flight instrument is to measure the trajectories of individual particles with sufficient accuracy to permit identification of their parent bodies and to capture enough impactor material to allow chemical and isotopic analyses of samples returned to Earth. Three different multiple-film small-particle capture cell designs (0.1-100-micron-thick Al foils with approx. 10, 100, and 1800 micron spacing) were evaluated for their ability to capture impactor fragments and residue. Their performances were compared to two other types of capture cells, foil covered Ge crystals, and 0.50 and 0.120 g/cu cm aerogels. All capture cells were tested behind multifilm (1.4-6.0-micron-thick) polyvinylidene fluoride (PVDF) velocity/trajectory sensor devices. Several tests were also done without the PVDF sensors for comparison. The results of this study were reported by Simon in a comprehensive report in which the morphology of impacts and impactor residues in various types of capture cells after passage through two PVDF sensor films is discussed. Impactor fragments in selected capture cells from impacts at velocities up to 6.4 km/s were identified using scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS).

Display of travelling 3D scenes from single integral-imaging capture

NASA Astrophysics Data System (ADS)

Martinez-Corral, Manuel; Dorado, Adrian; Hong, Seok-Min; Sola-Pikabea, Jorge; Saavedra, Genaro

2016-06-01

Integral imaging (InI) is a 3D auto-stereoscopic technique that captures and displays 3D images. We present a method for easily projecting the information recorded with this technique by transforming the integral image into a plenoptic image, as well as choosing, at will, the field of view (FOV) and the focused plane of the displayed plenoptic image. Furthermore, with this method we can generate a sequence of images that simulates a camera travelling through the scene from a single integral image. The application of this method permits to improve the quality of 3D display images and videos.

Wind wheel electric power generator

NASA Technical Reports Server (NTRS)

Kaufman, J. W. (Inventor)

1980-01-01

Wind wheel electric power generator apparatus includes a housing rotatably mounted upon a vertical support column. Primary and auxiliary funnel-type, venturi ducts are fixed onto the housing for capturing wind currents and conducting to a bladed wheel adapted to be operatively connected with the generator apparatus. Additional air flows are also conducted onto the bladed wheel; all of the air flows positively effecting rotation of the wheel in a cumulative manner. The auxiliary ducts are disposed at an acute angle with respect to the longitudinal axis of the housing, and this feature, together with the rotatability of the housing and the ducts, permits capture of wind currents within a variable directional range.

77 FR 22004 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978 (Pub. L. 95-541)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-12

...) capture, mark, band and/ or weigh adult, chicks and eggs of seabirds (Adelie, Chinstrap, and Gentoo... regurgitated prey items; (4) place transmitters on individuals; (5) place instrumented artificial eggs under..., feathers, yolk); (7) collect addled/infertile eggs no longer being incubated; (8) use GPS/GIS technologies...

Step-by-Step Visual Manuals: Design and Development

ERIC Educational Resources Information Center

Urata, Toshiyuki

2004-01-01

The types of handouts and manuals that are used in technology training vary. Some describe procedures in a narrative way without graphics; some employ step-by-step instructions with screen captures. According to Thirlway (1994), a training manual should be like a tutor that permits a student to learn at his own pace and gives him confidence for…

A Biosynthetic Scaffold that Facilitates Chondrocyte-Mediated Degradation and Promotes Articular Cartilage Extracellular Matrix Deposition.

PubMed

Sridhar, Balaji V; Dailing, Eric A; Brock, J Logan; Stansbury, Jeffrey W; Randolph, Mark A; Anseth, Kristi S

2015-12-01

Articular cartilage remains a significant clinical challenge to repair because of its limited self-healing capacity. Interest has grown in the delivery of autologous chondrocytes to cartilage defects, and combining cell-based therapies with scaffolds that capture aspects of native tissue and allow cell-mediated remodeling could improve outcomes. Currently, scaffold-based therapies with encapsulated chondrocytes permit matrix production; however, resorption of the scaffold often does not match the rate of matrix production by chondrocytes, which can limit functional tissue regeneration. Here, we designed a hybrid biosynthetic system consisting of poly (ethylene glycol) (PEG) endcapped with thiols and crosslinked by norbornene-functionalized gelatin via a thiol-ene photopolymerization. The protein crosslinker was selected to facilitate chondrocyte-mediated scaffold remodeling and matrix deposition. Gelatin was functionalized with norbornene to varying degrees (~4-17 norbornenes/gelatin), and the shear modulus of the resulting hydrogels was characterized (<0.1-0.5 kPa). Degradation of the crosslinked PEG-gelatin hydrogels by chondrocyte-secreted enzymes was confirmed by gel permeation chromatography. Finally, chondrocytes encapsulated in these biosynthetic scaffolds showed significantly increased glycosaminoglycan deposition over just 14 days of culture, while maintaining high levels of viability and producing a distributed matrix. These results indicate the potential of a hybrid PEG-gelatin hydrogel to permit chondrocyte-mediated remodeling and promote articular cartilage matrix production. Tunable scaffolds that can easily permit chondrocyte-mediated remodeling may be useful in designing treatment options for cartilage tissue engineering applications.

A Biosynthetic Scaffold that Facilitates Chondrocyte-Mediated Degradation and Promotes Articular Cartilage Extracellular Matrix Deposition

PubMed Central

Sridhar., Balaji V.; Dailing, Eric A.; Brock, J. Logan; Stansbury, Jeffrey W.; Randolph, Mark A.; Anseth, Kristi S.

2015-01-01

Articular cartilage remains a significant clinical challenge to repair because of its limited self-healing capacity. Interest has grown in the delivery of autologous chondrocytes to cartilage defects, and combining cell-based therapies with scaffolds that capture aspects of native tissue and allow cell-mediated remodeling could improve outcomes. Currently, scaffold-based therapies with encapsulated chondrocytes permit matrix production; however, resorption of the scaffold often does not match the rate of matrix production by chondrocytes, which can limit functional tissue regeneration. Here, we designed a hybrid biosynthetic system consisting of poly (ethylene glycol) (PEG) endcapped with thiols and crosslinked by norbornene-functionalized gelatin via a thiol-ene photopolymerization. The protein crosslinker was selected to facilitate chondrocyte-mediated scaffold remodeling and matrix deposition. Gelatin was functionalized with norbornene to varying degrees (~4–17 norbornenes/gelatin), and the shear modulus of the resulting hydrogels was characterized (<0.1–0.5 kPa). Degradation of the crosslinked PEG-gelatin hydrogels by chondrocyte-secreted enzymes was confirmed by gel permeation chromatography. Finally, chondrocytes encapsulated in these biosynthetic scaffolds showed significantly increased glycosaminoglycan deposition over just 14 days of culture, while maintaining high levels of viability and producing a distributed matrix. These results indicate the potential of a hybrid PEG-gelatin hydrogel to permit chondrocyte-mediated remodeling and promote articular cartilage matrix production. Tunable scaffolds that can easily permit chondrocyte-mediated remodeling may be useful in designing treatment options for cartilage tissue engineering applications. PMID:26900597

75 FR 53299 - Issuance of NPDES General Permits for Wastewater Lagoon Systems Located in Indian Country in...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-31

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9195-3] Issuance of NPDES General Permits for Wastewater... Elimination System (NPDES) general permits for wastewater lagoon systems that are located in Indian country in... general permit for wastewater lagoon systems that are located in Indian country in the State of Colorado...

A fast data acquisition system for the study of transient events by high repetition rate time-of-flight mass spectrometry

NASA Technical Reports Server (NTRS)

Lincoln, K. A.; Bechtel, R. D.

1986-01-01

Recent advances in commercially available data acquisition electronics embodying high speed A/D conversion coupled to increased memory storage have now made practical (at least within time intervals of a third of a millisecond or more) the capturing of all of the data generated by a high repetition rate time-of-flight mass spectrometer producing complete spectra every 25 to 35 microseconds. Such a system was assembled and interfaced with a personal computer for control and management of data. The applications are described for recording time-resolved spectra of individual vapor plumes induced from the pulsed-laser heating of material. Each laser pulse triggers the system to generate automatically a 3-dimensional (3-D) presentation of the time-resolved spectra with m/z labeling of the major mass peaks, plus an intensity versus time display of both the laser pulse and the resulting vapor pulse. The software also permits storing of data and its presentation in various additional forms.

Sustainable Diagnostic Tools for Site Characterization and Remediation

NASA Astrophysics Data System (ADS)

Driver, E. M.; Roll, I. B.; Supowit, S. D.; Halden, R. U.

2016-12-01

Three submersible diagnostic tools were developed to enable more precise and cost-effective means of sampling environmental waters and assessing remedial strategies. The In Situ Sampler (IS2) and In Situ Sampler for Biphasic Water Monitoring (IS2B), designed for sampling groundwater or simultaneous pore- and surface water, use affordable off-the-shelf solid phase extraction technology, applicable to a broad range of organic and inorganic contaminants. Flow-through design reduces hazardous waste generation, transportation costs, and carbon footprint by 90-98% compared to traditional methods. The IS2 is ideal for dynamic groundwater systems where discrete sampling may fail to capture temporal variations, leading to inaccurate assessment of exposure and risk. A 28-day sampling event in a Cr(VI)-impacted aquifer captured previously undetected tidally-induced fluctuations, while improving the reporting limit 8-fold. The IS2B elucidates contaminant partitioning and bioavailability, and was validated in a wetland-shallow aquifer system with the pesticide fipronil. Concentrations of total fipronil-related compounds were statistically indistinguishable from those determined by conventional techniques (p > 0.2), ranging from 9.9 ± 4.6 to 18.1 ± 4.6 ng/L in surface water and 9.1 ± 3.0 to 12.6 ± 2.1 ng/L in porewater. For groundwater remedial testing, the In Situ Microcosm Array (ISMA) was developed to integrate laboratory column treatability studies with pilot-scale field-testing, thus minimizing costs associated with sequential lab and field analyses. In situ operation maintains (geo)chemical and microbial groundwater parameters often destroyed by extraction and laboratory storage. Onboard effluent capture permits the deployment well to return to monitoring status immediately after instrument removal. All tools employ reusable internal components and may be operated by solar power. Case study results highlight the capabilities and application range of the each technology.

Evaluation of image quality

NASA Technical Reports Server (NTRS)

Pavel, M.

1993-01-01

This presentation outlines in viewgraph format a general approach to the evaluation of display system quality for aviation applications. This approach is based on the assumption that it is possible to develop a model of the display which captures most of the significant properties of the display. The display characteristics should include spatial and temporal resolution, intensity quantizing effects, spatial sampling, delays, etc. The model must be sufficiently well specified to permit generation of stimuli that simulate the output of the display system. The first step in the evaluation of display quality is an analysis of the tasks to be performed using the display. Thus, for example, if a display is used by a pilot during a final approach, the aesthetic aspects of the display may be less relevant than its dynamic characteristics. The opposite task requirements may apply to imaging systems used for displaying navigation charts. Thus, display quality is defined with regard to one or more tasks. Given a set of relevant tasks, there are many ways to approach display evaluation. The range of evaluation approaches includes visual inspection, rapid evaluation, part-task simulation, and full mission simulation. The work described is focused on two complementary approaches to rapid evaluation. The first approach is based on a model of the human visual system. A model of the human visual system is used to predict the performance of the selected tasks. The model-based evaluation approach permits very rapid and inexpensive evaluation of various design decisions. The second rapid evaluation approach employs specifically designed critical tests that embody many important characteristics of actual tasks. These are used in situations where a validated model is not available. These rapid evaluation tests are being implemented in a workstation environment.

76 FR 22891 - Modification to 2008 National Pollutant Discharge Elimination System (NPDES) General Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... Construction Activities AGENCY: Environmental Protection Agency (EPA). ACTION: Notice. SUMMARY: EPA Regions 1... System (NPDES) general permits for stormwater discharges associated with construction activity in order... permits will be referred to as ``permit'' or ``2008 construction general permit'' or ``2008 CGP.'' This...

Rapid differentiation of rocky mountain spotted fever from chickenpox, measles, and enterovirus infections and bacterial meningitis by frequency-pulsed electron capture gas-liquid chromatographic analysis of sera.

PubMed Central

Brooks, J B; McDade, J E; Alley, C C

1981-01-01

Normal sera and sera from patients with Rocky Mountain spotted fever, chickenpox, enterovirus infections, measles, and Neisseria meningitidis infections were extracted with organic solvents under acidic and basic conditions and then derivatized with trichloroethanol or heptafluorobutyric anhydride-ethanol to form electron-capturing derivatives of organic acids, alcohols, and amines. The derivatives were analyzed by frequency-pulsed electron capture gas-liquid chromatography (FPEC-GLC). There were unique differences in the FPEC-GLC profiles of sera obtained from patients with these respective diseases. With Rocky Mountain spotted fever patients, typical profiles were detected as early as 1 day after onset of disease and before antibody could be detected in the serum. Rapid diagnosis of Rocky Mountain spotted fever by FPEC-GLC could permit early and effective therapy, thus preventing many deaths from this disease. PMID:7276147

Morphology of seahorse head hydrodynamically aids in capture of evasive prey.

PubMed

Gemmell, Brad J; Sheng, Jian; Buskey, Edward J

2013-01-01

Syngnathid fish (seahorses, pipefish and sea dragons) are slow swimmers yet capture evasive prey (copepods) using a technique known as the 'pivot' feeding, which involves rapid movement to overcome prey escape capabilities. However, this feeding mode functions only at short range and requires approaching very closely to hydrodynamically sensitive prey without triggering an escape. Here we investigate the role of head morphology on prey capture using holographic and particle image velocimetry (PIV). We show that head morphology functions to create a reduced fluid deformation zone, minimizing hydrodynamic disturbance where feeding strikes occur (above the end of the snout), and permits syngnathid fish to approach highly sensitive copepod prey (Acartia tonsa) undetected. The results explain how these animals can successfully employ short range 'pivot' feeding effectively on evasive prey. The need to approach prey with stealth may have selected for a head shape that produces lower deformation rates than other fish.

SLOW $pi$$sup +$-MESON CAPTURE BY LIGHT NUCLEI IN THE CORRELATIONAL NUCLEAR MODEL (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shklyarevskii, G.M.

Absorption of slow pi /sup +/-mesons by light nuclei in the pi /sup +/ + A yields A' + 2p reaction is considered. It is shown that an investigation of the proton spectra permits one to study small range pair correlation between nuclear nucleons. Conditions in which the corresponding experiments should be carried out are indicated. (auth)

Criterion 7: Legal, institutional, and economic framework for forest conservation and sustainable management

Treesearch

Stephen R. Shifley; Francisco X. Aguilar; Nianfu Song; Susan I. Stewart; David J. Nowak; Dale D. Gormanson; W. Keith Moser; Sherri Wormstead; Eric J. Greenfield

2012-01-01

This criterion focuses on the social context of forests—the laws, policies, administrative rules, and social and economic institutions—that governs forest resource management and use. What society permits or restricts, encourages or discourages all influence the sustainability of forest resources. Criterion 7 captures this by turning attention to all the different...

76 FR 25307 - Incidental Take Permit and Habitat Conservation Plan for PacifiCorp Klamath Hydroelectric Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... incidental take of one ESA-listed species as a result of operation and maintenance of the Klamath..., pursue, hunt, shoot, wound, kill, trap, capture, or collect, or to attempt to engage in any such conduct... maintenance of the Klamath Hydroelectric Project (Project) and implementation of the Plan for a 10-year period...

50 CFR 222.308 - Permits for scientific purposes or for the enhancement of propagation or survival of species.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., if any, for the disposition of any dead specimen or its skeleton or other remains in a museum or... your staff (include name(s) and qualifications) will supervise or observe the capture or other taking...) Qualifications and experience of the staff; (vi) A written certification from a licensed veterinarian or from a...

50 CFR 222.308 - Permits for scientific purposes or for the enhancement of propagation or survival of species.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., if any, for the disposition of any dead specimen or its skeleton or other remains in a museum or... your staff (include name(s) and qualifications) will supervise or observe the capture or other taking...) Qualifications and experience of the staff; (vi) A written certification from a licensed veterinarian or from a...

50 CFR 222.308 - Permits for scientific purposes or for the enhancement of propagation or survival of species.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., if any, for the disposition of any dead specimen or its skeleton or other remains in a museum or... your staff (include name(s) and qualifications) will supervise or observe the capture or other taking...) Qualifications and experience of the staff; (vi) A written certification from a licensed veterinarian or from a...

Sensitivity of a Simulated Derecho Event to Model Initial Conditions

NASA Astrophysics Data System (ADS)

Wang, Wei

2014-05-01

Since 2003, the MMM division at NCAR has been experimenting cloud-permitting scale weather forecasting using Weather Research and Forecasting (WRF) model. Over the years, we've tested different model physics, and tried different initial and boundary conditions. Not surprisingly, we found that the model's forecasts are more sensitive to the initial conditions than model physics. In 2012 real-time experiment, WRF-DART (Data Assimilation Research Testbed) at 15 km was employed to produce initial conditions for twice-a-day forecast at 3 km. On June 29, this forecast system captured one of the most destructive derecho event on record. In this presentation, we will examine forecast sensitivity to different model initial conditions, and try to understand the important features that may contribute to the success of the forecast.

78 FR 25435 - Draft National Pollutant Discharge Elimination System (NPDES) General Permit for Municipal...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-01

... (NPDES) General Permit for Municipal Separate Storm Sewer Systems in the Middle Rio Grande Watershed in... Elimination System (NPDES) general permit for storm water discharges from municipal separate storm sewer... issued for various categories of storm water discharges. Section 402(p)(2) requires permits for five...

A likelihood framework for joint estimation of salmon abundance and migratory timing using telemetric mark-recapture

USGS Publications Warehouse

Bromaghin, Jeffrey F.; Gates, Kenneth S.; Palmer, Douglas E.

2010-01-01

Many fisheries for Pacific salmon Oncorhynchus spp. are actively managed to meet escapement goal objectives. In fisheries where the demand for surplus production is high, an extensive assessment program is needed to achieve the opposing objectives of allowing adequate escapement and fully exploiting the available surplus. Knowledge of abundance is a critical element of such assessment programs. Abundance estimation using mark—recapture experiments in combination with telemetry has become common in recent years, particularly within Alaskan river systems. Fish are typically captured and marked in the lower river while migrating in aggregations of individuals from multiple populations. Recapture data are obtained using telemetry receivers that are co-located with abundance assessment projects near spawning areas, which provide large sample sizes and information on population-specific mark rates. When recapture data are obtained from multiple populations, unequal mark rates may reflect a violation of the assumption of homogeneous capture probabilities. A common analytical strategy is to test the hypothesis that mark rates are homogeneous and combine all recapture data if the test is not significant. However, mark rates are often low, and a test of homogeneity may lack sufficient power to detect meaningful differences among populations. In addition, differences among mark rates may provide information that could be exploited during parameter estimation. We present a temporally stratified mark—recapture model that permits capture probabilities and migratory timing through the capture area to vary among strata. Abundance information obtained from a subset of populations after the populations have segregated for spawning is jointly modeled with telemetry distribution data by use of a likelihood function. Maximization of the likelihood produces estimates of the abundance and timing of individual populations migrating through the capture area, thus yielding substantially more information than the total abundance estimate provided by the conventional approach. The utility of the model is illustrated with data for coho salmon O. kisutch from the Kasilof River in south-central Alaska.

Neutron-beam-shaping assembly for boron neutron-capture therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zaidi, L.; Kashaeva, E. A.; Lezhnin, S. I.

A neutron-beam-shaping assembly consisting of a moderator, a reflector, and an absorber is used to form a therapeutic neutron beam for the boron neutron-capture therapy of malignant tumors at accelerator neutron sources. A new structure of the moderator and reflector is proposed in the present article, and the results of a numerical simulation of the neutron spectrum and of the absorbed dose in a modified Snyder head phantom are presented. The application of a composite moderator and of a composite reflector and the implementation of neutron production at the proton energy of 2.3MeV are shown to permit obtaining a high-qualitymore » therapeutic neutron beam.« less

The Johnson Space Center Experimental Impact Lab: Contributions Toward Understanding the Evolution of the Solar System

NASA Technical Reports Server (NTRS)

See, T. H.; Montes, R.

2012-01-01

Impact is the most common and only weathering phenomenon affecting all the planetary bodies (e.g., planets, satellites, asteroids, comets, etc.) in the solar system. NASA Johnson Space Center s Experimental Impact Laboratory (EIL) includes three accelerators that are used in support of research into the effects of impact on the formation and evolution of the solar system. They permit researchers to study a wide variety of phenomena associated with high-velocity impacts into a wide range of geologic targets and materials relevant to astrobiological studies. By studying these processes, researchers can investigate the histories and evolution of planetary bodies and the solar system as a whole. While the majority of research conducted in the EIL addresses questions involving planetary impacts, work involving spacecraft components has been performed on occasion. An example of this is the aerogel collector material flown on the Stardust spacecraft that traveled to Comet Wild-2. This capture medium was tested and flight qualified using the 5 mm Light-Gas Gun located in the EIL.

A High-Order, Time Invariant, Linearized Model for Application to HHCIAFCS Interaction Studies

NASA Technical Reports Server (NTRS)

Cheng, Rendy P.; Tischler, Mark B.; Celi, Roberto

2003-01-01

This paper describes a methodology for the extraction of a linear time invariant model from a nonlinear helicopter model, and followed by an examination of the interactions of the Higher Harmonic Control (HHC) and the Automatic Flight Control System (AFCS). This new method includes an embedded harmonic analyzer inside a linear time invariant model, which allows the periodicity of the helicopter response to be captured. The: coupled high-order model provides the needed level of dynamic fidelity to permit an analysis and optimization of the AFCS and HHC loops. Results of this study indicate that the closed-loop HHC system has little influence on the AFCS or on the vehicle handling qualities, which indicates that the AFCS does not need modification to work with the HHC system. The results also show that the vibration response to maneuvers must be considered during the HHC design process, which leads to much higher required HHC loop crossover frequencies. This research also demonstrates that the transient vibration response during maneuvers can be reduced by optimizing the closed-loop higher harmonic control laws using conventional control system analyses.

Standardised Embedded Data framework for Drones [SEDD

NASA Astrophysics Data System (ADS)

Wyngaard, J.; Barbieri, L.; Peterson, F. S.

2015-12-01

A number of barriers to entry remain for UAS use in science. One in particular is that of implementing an experiment and UAS specific software stack. Currently this stack is most often developed in-house and customised for a particular UAS-sensor pairing - limiting its reuse. Alternatively, when adaptable a suitable commercial package may be used, but such systems are both costly and usually suboptimal.In order to address this challenge the Standardised Embedded Data framework for Drones [SEDD] is being developed in μpython. SEDD provides an open source, reusable, and scientist-accessible drop in solution for drone data capture and triage. Targeted at embedded hardware, and offering easy access to standard I/O interfaces, SEDD provides an easy solution for simply capturing data from a sensor. However, the intention is rather to enable more complex systems of multiple sensors, computer hardware, and feedback loops, via 3 primary components.A data asset manager ensures data assets are associated with appropriate metadata as they are captured. Thereafter, the asset is easily archived or otherwise redirected, possibly to - onboard storage, onboard compute resource for processing, an interface for transmission, another sensor control system, remote storage and processing (such as EarthCube's CHORDS), or to any combination of the above.A service workflow managerenables easy implementation of complex onboard systems via dedicated control of multiple continuous and periodic services. Such services will include the housekeeping chores of operating a UAS and multiple sensors, but will also permit a scientist to drop in an initial scientific data processing code utilising on-board compute resources beyond the autopilot. Having such capabilities firstly enables easy creation of real-time feedback, to the human- or auto- pilot, or other sensors, on data quality or needed flight path changes. Secondly, compute hardware provides the opportunity to carry out real-time data triage, for the purposes of conserving on-board storage space or transmission bandwidth in inherently poor connectivity environments.A compute manager is finally included. Depending on system complexity, and given the need for power efficient parallelism, it can quickly become necessary to provide a scheduling service for multiple workflows.

Comet coma sample return instrument

NASA Technical Reports Server (NTRS)

Albee, A. L.; Brownlee, Don E.; Burnett, Donald S.; Tsou, Peter; Uesugi, K. T.

1994-01-01

The sample collection technology and instrument concept for the Sample of Comet Coma Earth Return Mission (SOCCER) are described. The scientific goals of this Flyby Sample Return are to return to coma dust and volatile samples from a known comet source, which will permit accurate elemental and isotopic measurements for thousands of individual solid particles and volatiles, detailed analysis of the dust structure, morphology, and mineralogy of the intact samples, and identification of the biogenic elements or compounds in the solid and volatile samples. Having these intact samples, morphologic, petrographic, and phase structural features can be determined. Information on dust particle size, shape, and density can be ascertained by analyzing penetration holes and tracks in the capture medium. Time and spatial data of dust capture will provide understanding of the flux dynamics of the coma and the jets. Additional information will include the identification of cosmic ray tracks in the cometary grains, which can provide a particle's process history and perhaps even the age of the comet. The measurements will be made with the same equipment used for studying micrometeorites for decades past; hence, the results can be directly compared without extrapolation or modification. The data will provide a powerful and direct technique for comparing the cometary samples with all known types of meteorites and interplanetary dust. This sample collection system will provide the first sample return from a specifically identified primitive body and will allow, for the first time, a direct method of matching meteoritic materials captured on Earth with known parent bodies.

Estimation of sex-specific survival from capture-recapture data when sex is not always known

USGS Publications Warehouse

Nichols, J.D.; Kendall, W.L.; Hines, J.E.; Spendelow, J.A.

2004-01-01

Many animals lack obvious sexual dimorphism, making assignment of sex difficult even for observed or captured animals. For many such species it is possible to assign sex with certainty only at some occasions; for example, when they exhibit certain types of behavior. A common approach to handling this situation in capture-recapture studies has been to group capture histories into those of animals eventually identified as male and female and those for which sex was never known. Because group membership is dependent on the number of occasions at which an animal was caught or observed (known sex animals, on average, will have been observed at more occasions than unknown-sex animals), survival estimates for known-sex animals will be positively biased, and those for unknown animals will be negatively biased. In this paper, we develop capture-recapture models that incorporate sex ratio and sex assignment parameters that permit unbiased estimation in the face of this sampling problem. We demonstrate the magnitude of bias in the traditional capture-recapture approach to this sampling problem, and we explore properties of estimators from other ad hoc approaches. The model is then applied to capture-recapture data for adult Roseate Terns (Sterna dougallii) at Falkner Island, Connecticut, 1993-2002. Sex ratio among adults in this population favors females, and we tested the hypothesis that this population showed sex-specific differences in adult survival. Evidence was provided for higher survival of adult females than males, as predicted. We recommend use of this modeling approach for future capture-recapture studies in which sex cannot always be assigned to captured or observed animals. We also place this problem in the more general context of uncertainty in state classification in multistate capture-recapture models.

Investigations of potential bias in the estimation of lambda using Pradel's (1996) model for capture-recapture data

USGS Publications Warehouse

Hines, James E.; Nichols, James D.

2002-01-01

Pradel's (1996) temporal symmetry model permitting direct estimation and modelling of population growth rate, u i , provides a potentially useful tool for the study of population dynamics using marked animals. Because of its recent publication date, the approach has not seen much use, and there have been virtually no investigations directed at robustness of the resulting estimators. Here we consider several potential sources of bias, all motivated by specific uses of this estimation approach. We consider sampling situations in which the study area expands with time and present an analytic expression for the bias in u i We next consider trap response in capture probabilities and heterogeneous capture probabilities and compute large-sample and simulation-based approximations of resulting bias in u i . These approximations indicate that trap response is an especially important assumption violation that can produce substantial bias. Finally, we consider losses on capture and emphasize the importance of selecting the estimator for u i that is appropriate to the question being addressed. For studies based on only sighting and resighting data, Pradel's (1996) u i ' is the appropriate estimator.

Investigation of Body Force Effects on Flow Boiling Critical Heat Flux

NASA Technical Reports Server (NTRS)

Zhang, Hui; Mudawar, Issam; Hasan, Mohammad M.

2002-01-01

The bubble coalescence and interfacial instabilities that are important to modeling critical heat flux (CHF) in reduced-gravity systems can be sensitive to even minute body forces. Understanding these complex phenomena is vital to the design and safe implementation of two-phase thermal management loops proposed for space and planetary-based thermal systems. While reduced gravity conditions cannot be accurately simulated in 1g ground-based experiments, such experiments can help isolate the effects of the various forces (body force, surface tension force and inertia) which influence flow boiling CHF. In this project, the effects of the component of body force perpendicular to a heated wall were examined by conducting 1g flow boiling experiments at different orientations. FC-72 liquid was boiled along one wall of a transparent rectangular flow channel that permitted photographic study of the vapor-liquid interface at conditions approaching CHF. High-speed video imaging was employed to capture dominant CHF mechanisms. Six different CHF regimes were identified: Wavy Vapor Layer, Pool Boiling, Stratification, Vapor Counterflow, Vapor Stagnation, and Separated Concurrent Vapor Flow. CHF showed great sensitivity to orientation for flow velocities below 0.2 m/s, where very small CHF values where measured, especially with downflow and downward-facing heated wall orientations. High flow velocities dampened the effects of orientation considerably. Figure I shows representative images for the different CHF regimes. The Wavy Vapor Layer regime was dominant for all high velocities and most orientations, while all other regimes were encountered at low velocities, in the downflow and/or downward-facing heated wall orientations. The Interfacial Lift-off model was modified to predict the effects of orientation on CHF for the dominant Wavy Vapor Layer regime. The photographic study captured a fairly continuous wavy vapor layer travelling along the heated wall while permitting liquid contact only in wetting fronts, located in the troughs of the interfacial waves. CHF commenced when wetting fronts near the outlet were lifted off the wall. The Interfacial Lift-off model is shown to be an effective tool for predicting the effects of body force on CHF at high velocities.

Latest CMB Measurement Results

NASA Astrophysics Data System (ADS)

Bock, James

2014-01-01

We have allocated time in this special session to capture the latest developments in balloon-borne and ground-based CMB measurements. The speaker for this oral presentation will be chosen at a later date in order to best highlight emerging results. This session also includes presentations from current CMB experiments in a parallel poster session. Time-permitting, the latest community plans for future CMB measurement facilities may also be discussed.

Characterization of Mesoscale Predictability

DTIC Science & Technology

2013-09-30

2009), which, it had been argued, had high mesoscale predictability. More recently, we have considered the prediction of lowland snow in the Puget ...averaged total and perturbation kinetic energy spectra on the 5-km, convection-permitting grid. The ensembles clearly captured the observed k-5/3 total...kinetic energy spectrum at wavelengths less than approximately 400 km and also showed a transition to a roughly k-3 dependence at longer wavelengths

TARDEC's Intelligent Ground Systems overview

NASA Astrophysics Data System (ADS)

Jaster, Jeffrey F.

2009-05-01

The mission of the Intelligent Ground Systems (IGS) Area at the Tank Automotive Research, Development and Engineering Center (TARDEC) is to conduct technology maturation and integration to increase Soldier robot control/interface intuitiveness and robotic ground system robustness, functionality and overall system effectiveness for the Future Combat System Brigade Combat Team, Robotics Systems Joint Project Office and game changing capabilities to be fielded beyond the current force. This is accomplished through technology component development focused on increasing unmanned ground vehicle autonomy, optimizing crew interfaces and mission planners that capture commanders' intent, integrating payloads that provide 360 degree local situational awareness and expanding current UGV tactical behavior, learning and adaptation capabilities. The integration of these technology components into ground vehicle demonstrators permits engineering evaluation, User assessment and performance characterization in increasingly complex, dynamic and relevant environments to include high speed on road or cross country operations, all weather/visibility conditions and military operations in urban terrain (MOUT). Focused testing and experimentation is directed at reducing PM risk areas (safe operations, autonomous maneuver, manned-unmanned collaboration) and transitioning technology in the form of hardware, software algorithms, test and performance data, as well as User feedback and lessons learned.

Estimating breeding proportions and testing hypotheses about costs of reproduction with capture-recapture data

USGS Publications Warehouse

Nichols, James D.; Hines, James E.; Pollock, Kenneth H.; Hinz, Robert L.; Link, William A.

1994-01-01

The proportion of animals in a population that breeds is an important determinant of population growth rate. Usual estimates of this quantity from field sampling data assume that the probability of appearing in the capture or count statistic is the same for animals that do and do not breed. A similar assumption is required by most existing methods used to test ecologically interesting hypotheses about reproductive costs using field sampling data. However, in many field sampling situations breeding and nonbreeding animals are likely to exhibit different probabilities of being seen or caught. In this paper, we propose the use of multistate capture-recapture models for these estimation and testing problems. This methodology permits a formal test of the hypothesis of equal capture/sighting probabilities for breeding and nonbreeding individuals. Two estimators of breeding proportion (and associated standard errors) are presented, one for the case of equal capture probabilities and one for the case of unequal capture probabilities. The multistate modeling framework also yields formal tests of hypotheses about reproductive costs to future reproduction or survival or both fitness components. The general methodology is illustrated using capture-recapture data on female meadow voles, Microtus pennsylvanicus. Resulting estimates of the proportion of reproductively active females showed strong seasonal variation, as expected, with low breeding proportions in midwinter. We found no evidence of reproductive costs extracted in subsequent survival or reproduction. We believe that this methodological framework has wide application to problems in animal ecology concerning breeding proportions and phenotypic reproductive costs.

Capture of activation during ventricular arrhythmia using distributed stimulation.

PubMed

Meunier, Jason M; Ramalingam, Sanjiv; Lin, Shien-Fong; Patwardhan, Abhijit R

2007-04-01

Results of previous studies suggest that pacing strength stimuli can capture activation during ventricular arrhythmia locally near pacing sites. The existence of spatio-temporal distribution of excitable gap during arrhythmia suggests that multiple and timed stimuli delivered over a region may permit capture over larger areas. Our objective in this study was to evaluate the efficacy of using spatially distributed pacing (DP) to capture activation during ventricular arrhythmia. Data were obtained from rabbit hearts which were placed against a lattice of parallel wires through which biphasic pacing stimuli were delivered. Electrical activity was recorded optically. Pacing stimuli were delivered in sequence through the parallel wires starting with the wire closest to the apex and ending with one closest to the base. Inter-stimulus delay was based on conduction velocity. Time-frequency analysis of optical signals was used to determine variability in activation. A decrease in standard deviation of dominant frequencies of activation from a grid of locations that spanned the captured area and a concurrence with paced frequency were used as an index of capture. Results from five animals showed that the average standard deviation decreased from 0.81 Hz during arrhythmia to 0.66 Hz during DP at pacing cycle length of 125 ms (p = 0.03) reflecting decreased spatio-temporal variability in activation during DP. Results of time-frequency analysis during these pacing trials showed agreement between activation and paced frequencies. These results show that spatially distributed and timed stimulation can be used to modify and capture activation during ventricular arrhythmia.

Bioelectric Control of a 757 Class High Fidelity Aircraft Simulation

NASA Technical Reports Server (NTRS)

Jorgensen, Charles; Wheeler, Kevin; Stepniewski, Slawomir; Norvig, Peter (Technical Monitor)

2000-01-01

This paper presents results of a recent experiment in fine grain Electromyographic (EMG) signal recognition, We demonstrate bioelectric flight control of 757 class simulation aircraft landing at San Francisco International Airport. The physical instrumentality of a pilot control stick is not used. A pilot closes a fist in empty air and performs control movements which are captured by a dry electrode array on the arm, analyzed and routed through a flight director permitting full pilot outer loop control of the simulation. A Vision Dome immersive display is used to create a VR world for the aircraft body mechanics and flight changes to pilot movements. Inner loop surfaces and differential aircraft thrust is controlled using a hybrid neural network architecture that combines a damage adaptive controller (Jorgensen 1998, Totah 1998) with a propulsion only based control system (Bull & Kaneshige 1997). Thus the 757 aircraft is not only being flown bioelectrically at the pilot level but also demonstrates damage adaptive neural network control permitting adaptation to severe changes in the physical flight characteristics of the aircraft at the inner loop level. To compensate for accident scenarios, the aircraft uses remaining control surface authority and differential thrust from the engines. To the best of our knowledge this is the first time real time bioelectric fine-grained control, differential thrust based control, and neural network damage adaptive control have been integrated into a single flight demonstration. The paper describes the EMG pattern recognition system and the bioelectric pattern recognition methodology.

Climate change impacts and adaptive strategies: lessons from the grapevine.

PubMed

Mosedale, Jonathan R; Abernethy, Kirsten E; Smart, Richard E; Wilson, Robert J; Maclean, Ilya M D

2016-11-01

The cultivation of grapevines for winemaking, known as viticulture, is widely cited as a climate-sensitive agricultural system that has been used as an indicator of both historic and contemporary climate change. Numerous studies have questioned the viability of major viticulture regions under future climate projections. We review the methods used to study the impacts of climate change on viticulture in the light of what is known about the effects of climate and weather on the yields and quality of vineyard harvests. Many potential impacts of climate change on viticulture, particularly those associated with a change in climate variability or seasonal weather patterns, are rarely captured. Key biophysical characteristics of viticulture are often unaccounted for, including the variability of grapevine phenology and the exploitation of microclimatic niches that permit successful cultivation under suboptimal macroclimatic conditions. We consider how these same biophysical characteristics permit a variety of strategies by which viticulture can adapt to changing climatic conditions. The ability to realize these strategies, however, is affected by uneven exposure to risks across the winemaking sector, and the evolving capacity for decision-making within and across organizational boundaries. The role grape provenance plays in shaping perceptions of wine value and quality illustrates how conflicts of interest influence decisions about adaptive strategies within the industry. We conclude by considering what lessons can be taken from viticulture for studies of climate change impacts and the capacity for adaptation in other agricultural and natural systems. © 2016 John Wiley & Sons Ltd.

77 FR 6112 - Notice of Final National Pollutant Discharge Elimination System (NPDES) General Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-07

... Elimination System (NPDES) General Permit for Discharges From Concentrated Animal Feeding Operations (CAFOs... permit for discharges from eligible owners/operators of concentrated animal feeding operations (CAFOs... of the final permit, animal feeding operations that are defined as CAFOs or designated as CAFOs by...

75 FR 4554 - Modification to 2008 National Pollutant Discharge Elimination System (NPDES) General Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-28

... Construction Activities AGENCY: Environmental Protection Agency (EPA). ACTION: Notice. SUMMARY: EPA Regions 1... System (NPDES) general permits for stormwater discharges associated with construction activity in order... will be referred to as ``permit'' or ``2008 construction general permit'' or ``2008 CGP.'' The 2008 CGP...

Program manual for HILTOP, a heliocentric interplanetary low thrust trajectory optimization program. Part 1: User's guide

NASA Technical Reports Server (NTRS)

Mann, F. I.; Horsewood, J. L.

1974-01-01

A performance-analysis computer program, that was developed explicitly to generate optimum electric propulsion trajectory data for missions of interest in the exploration of the solar system is presented. The program was primarily designed to evaluate the performance capabilities of electric propulsion systems, and in the simulation of a wide variety of interplanetary missions. A numerical integration of the two-body, three-dimensional equations of motion and the Euler-Lagrange equations was used in the program. Transversality conditions which permit the rapid generation of converged maximum-payload trajectory data, and the optimization of numerous other performance indices for which no transversality conditions exist are included. The ability to simulate constrained optimum solutions, including trajectories having specified propulsion time and constant thrust cone angle, is also in the program. The program was designed to handle multiple-target missions with various types of encounters, such as rendezvous, stopover, orbital capture, and flyby. Performance requirements for a variety of launch vehicles can be determined.

Electromagnetic tracking of motion in the proximity of computer generated graphical stimuli: a tutorial.

PubMed

Schnabel, Ulf H; Hegenloh, Michael; Müller, Hermann J; Zehetleitner, Michael

2013-09-01

Electromagnetic motion-tracking systems have the advantage of capturing the tempo-spatial kinematics of movements independently of the visibility of the sensors. However, they are limited in that they cannot be used in the proximity of electromagnetic field sources, such as computer monitors. This prevents exploiting the tracking potential of the sensor system together with that of computer-generated visual stimulation. Here we present a solution for presenting computer-generated visual stimulation that does not distort the electromagnetic field required for precise motion tracking, by means of a back projection medium. In one experiment, we verify that cathode ray tube monitors, as well as thin-film-transistor monitors, distort electro-magnetic sensor signals even at a distance of 18 cm. Our back projection medium, by contrast, leads to no distortion of the motion-tracking signals even when the sensor is touching the medium. This novel solution permits combining the advantages of electromagnetic motion tracking with computer-generated visual stimulation.

Priority Queuing Models for Hospital Intensive Care Units and Impacts to Severe Case Patients

PubMed Central

Hagen, Matthew S.; Jopling, Jeffrey K; Buchman, Timothy G; Lee, Eva K.

2013-01-01

This paper examines several different queuing models for intensive care units (ICU) and the effects on wait times, utilization, return rates, mortalities, and number of patients served. Five separate intensive care units at an urban hospital are analyzed and distributions are fitted for arrivals and service durations. A system-based simulation model is built to capture all possible cases of patient flow after ICU admission. These include mortalities and returns before and after hospital exits. Patients are grouped into 9 different classes that are categorized by severity and length of stay (LOS). Each queuing model varies by the policies that are permitted and by the order the patients are admitted. The first set of models does not prioritize patients, but examines the advantages of smoothing the operating schedule for elective surgeries. The second set analyzes the differences between prioritizing admissions by expected LOS or patient severity. The last set permits early ICU discharges and conservative and aggressive bumping policies are contrasted. It was found that prioritizing patients by severity considerably reduced delays for critical cases, but also increased the average waiting time for all patients. Aggressive bumping significantly raised the return and mortality rates, but more conservative methods balance quality and efficiency with lowered wait times without serious consequences. PMID:24551379

High-repetition-rate interferometric Rayleigh scattering for flow-velocity measurements

NASA Astrophysics Data System (ADS)

Estevadeordal, Jordi; Jiang, Naibo; Cutler, Andrew D.; Felver, Josef J.; Slipchenko, Mikhail N.; Danehy, Paul M.; Gord, James R.; Roy, Sukesh

2018-03-01

High-repetition-rate interferometric-Rayleigh-scattering (IRS) velocimetry is demonstrated for non-intrusive, high-speed flow-velocity measurements. High temporal resolution is obtained with a quasi-continuous burst-mode laser that is capable of operating at 10-100 kHz, providing 10-ms bursts with pulse widths of 5-1000 ns and pulse energy > 100 mJ at 532 nm. Coupled with a high-speed camera system, the IRS method is based on imaging the flow field through an etalon with 8-GHz free spectral range and capturing the Doppler shift of the Rayleigh-scattered light from the flow at multiple points having constructive interference. The seed-laser linewidth permits a laser linewidth of < 150 MHz at 532 nm. The technique is demonstrated in a high-speed jet, and high-repetition-rate image sequences are shown.

Modeling for (physical) biologists: an introduction to the rule-based approach

PubMed Central

Chylek, Lily A; Harris, Leonard A; Faeder, James R; Hlavacek, William S

2015-01-01

Models that capture the chemical kinetics of cellular regulatory networks can be specified in terms of rules for biomolecular interactions. A rule defines a generalized reaction, meaning a reaction that permits multiple reactants, each capable of participating in a characteristic transformation and each possessing certain, specified properties, which may be local, such as the state of a particular site or domain of a protein. In other words, a rule defines a transformation and the properties that reactants must possess to participate in the transformation. A rule also provides a rate law. A rule-based approach to modeling enables consideration of mechanistic details at the level of functional sites of biomolecules and provides a facile and visual means for constructing computational models, which can be analyzed to study how system-level behaviors emerge from component interactions. PMID:26178138

Polymersome magneto-valves for reversible capture and release of nanoparticles

PubMed Central

van Rhee, P.G.; Rikken, R.S.M.; Abdelmohsen, L.K.E.A.; Maan, J.C.; Nolte, R.J.M.; van Hest, J.C.M.; Christianen, P.C.M.; Wilson, D.A.

2014-01-01

Stomatocytes are polymersomes with an infolded bowl-shaped architecture. This internal cavity is connected to the outside environment via a small ‘mouth’ region. Stomatocytes are assembled from diamagnetic amphiphilic block-copolymers with a highly anisotropic magnetic susceptibility, which permits to magnetically align and deform the polymeric self-assemblies. Here we show the reversible opening and closing of the mouth region of stomatocytes in homogeneous magnetic fields. The control over the size of the opening yields magneto-responsive supramolecular valves that are able to reversibly capture and release cargo. Furthermore, the increase in the size of the opening is gradual and starts at fields below 10 T, which opens the possibility of using these structures for delivery and nanoreactor applications. PMID:25248402

Integral imaging with Fourier-plane recording

NASA Astrophysics Data System (ADS)

Martínez-Corral, M.; Barreiro, J. C.; Llavador, A.; Sánchez-Ortiga, E.; Sola-Pikabea, J.; Scrofani, G.; Saavedra, G.

2017-05-01

Integral Imaging is well known for its capability of recording both the spatial and the angular information of threedimensional (3D) scenes. Based on such an idea, the plenoptic concept has been developed in the past two decades, and therefore a new camera has been designed with the capacity of capturing the spatial-angular information with a single sensor and after a single shot. However, the classical plenoptic design presents two drawbacks, one is the oblique recording made by external microlenses. Other is loss of information due to diffraction effects. In this contribution report a change in the paradigm and propose the combination of telecentric architecture and Fourier-plane recording. This new capture geometry permits substantial improvements in resolution, depth of field and computation time

KSC-2014-3529

NASA Image and Video Library

2014-08-14

CAPE CANAVERAL, Fla. – This view from the NASA Press Site parking lot captures storm clouds approaching Launch Pad 39B, in the distance at right, at NASA’s Kennedy Space Center in Florida. Kennedy's Ground Support Development and Operations Program is hard at work transforming the center's facilities into a multi-user spaceport, when the weather permits. For more on Kennedy Space Center, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Ben Smegelsky

Blackboard architecture for medical image interpretation

NASA Astrophysics Data System (ADS)

Davis, Darryl N.; Taylor, Christopher J.

1991-06-01

There is a growing interest in using sophisticated knowledge-based systems for biomedical image interpretation. We present a principled attempt to use artificial intelligence methodologies in interpreting lateral skull x-ray images. Such radiographs are routinely used in cephalometric analysis to provide quantitative measurements useful to clinical orthodontists. Manual and interactive methods of analysis are known to be error prone and previous attempts to automate this analysis typically fail to capture the expertise and adaptability required to cope with the variability in biological structure and image quality. An integrated model-based system has been developed which makes use of a blackboard architecture and multiple knowledge sources. A model definition interface allows quantitative models, of feature appearance and location, to be built from examples as well as more qualitative modelling constructs. Visual task definition and blackboard control modules allow task-specific knowledge sources to act on information available to the blackboard in a hypothesise and test reasoning cycle. Further knowledge-based modules include object selection, location hypothesis, intelligent segmentation, and constraint propagation systems. Alternative solutions to given tasks are permitted.

Conditional-sampling spectrograph detection system for fluorescence measurements of individual airborne biological particles

NASA Astrophysics Data System (ADS)

Nachman, Paul; Pinnick, R. G.; Hill, Steven C.; Chen, Gang; Chang, Richard K.; Mayo, Michael W.; Fernandez, Gilbert L.

1996-03-01

We report the design and operation of a prototype conditional-sampling spectrograph detection system that can record the fluorescence spectra of individual, micrometer-sized aerosols as they traverse an intense 488-nm intracavity laser beam. The instrument's image-intensified CCD detector is gated by elastic scattering or by undispersed fluorescence from particles that enter the spectrograph's field of view. It records spectra only from particles with preselected scattering-fluorescence levels (a fiber-optic-photomultiplier subsystem provides the gating signal). This conditional-sampling procedure reduces data-handling rates and increases the signal-to-noise ratio by restricting the system's exposures to brief periods when aerosols traverse the beam. We demonstrate these advantages by reliably capturing spectra from individual fluorescent microspheres dispersed in an airstream. The conditional-sampling procedure also permits some discrimination among different types of particles, so that spectra may be recorded from the few interesting particles present in a cloud of background aerosol. We demonstrate such discrimination by measuring spectra from selected fluorescent microspheres in a mixture of two types of microspheres, and from bacterial spores in a mixture of spores and nonfluorescent kaolin particles.

High throughput imaging cytometer with acoustic focussing.

PubMed

Zmijan, Robert; Jonnalagadda, Umesh S; Carugo, Dario; Kochi, Yu; Lemm, Elizabeth; Packham, Graham; Hill, Martyn; Glynne-Jones, Peter

2015-10-31

We demonstrate an imaging flow cytometer that uses acoustic levitation to assemble cells and other particles into a sheet structure. This technique enables a high resolution, low noise CMOS camera to capture images of thousands of cells with each frame. While ultrasonic focussing has previously been demonstrated for 1D cytometry systems, extending the technology to a planar, much higher throughput format and integrating imaging is non-trivial, and represents a significant jump forward in capability, leading to diagnostic possibilities not achievable with current systems. A galvo mirror is used to track the images of the moving cells permitting exposure times of 10 ms at frame rates of 50 fps with motion blur of only a few pixels. At 80 fps, we demonstrate a throughput of 208 000 beads per second. We investigate the factors affecting motion blur and throughput, and demonstrate the system with fluorescent beads, leukaemia cells and a chondrocyte cell line. Cells require more time to reach the acoustic focus than beads, resulting in lower throughputs; however a longer device would remove this constraint.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kupar, J.; Hasek, M.

The Sanitary Landfill Corrective Action Plan proposes a two pronged approach to remediation. The first part of the total remediation strategy is the placement of a RCRA style closure cap to provide source control of contaminants into the groundwater. The second part of the proposed remediation package is a phased approach primarily using an in situ bioremediation system for groundwater clean up of the Constituents of Concern (COCs) that exceed their proposed Alternate Concentration Limits (ACL). The phased in approach of groundwater clean up will involve operation of the in situ bioremediation system, followed by evaluation of the Phase 1more » system and, if necessary, additional phased remediation strategies. This document presents pertinent information on operations, well locations, anticipated capture zones, monitoring strategies, observation wells and other information which will allow a decision on the acceptability of the remedial strategy as an interim corrective action prior to permit application approval. The proposed interim phase of the remediation program will position two horizontal bioremediation wells such that the respective zones of influence will intersect the migration path for the highest concentrations of each plume.« less

Online Systems for Oversize and Overweight Freight Permitting and Motor Carrier Credentialing : Transportation Research Synthesis.

DOT National Transportation Integrated Search

2017-09-01

MnDOT uses two online systems implemented in the 1990s to issue and manage permits for oversize/overweight (OS/OW) freight and motor carrier credentials: - RouteBuilder, an OS/OW permitting system with a routing component. - Motor Carrier Information...

Design knowledge capture for a corporate memory facility

NASA Technical Reports Server (NTRS)

Boose, John H.; Shema, David B.; Bradshaw, Jeffrey M.

1990-01-01

Currently, much of the information regarding decision alternatives and trade-offs made in the course of a major program development effort is not represented or retained in a way that permits computer-based reasoning over the life cycle of the program. The loss of this information results in problems in tracing design alternatives to requirements, in assessing the impact of change in requirements, and in configuration management. To address these problems, the problem was studied of building an intelligent, active corporate memory facility which would provide for the capture of the requirements and standards of a program, analyze the design alternatives and trade-offs made over the program's lifetime, and examine relationships between requirements and design trade-offs. Early phases of the work have concentrated on design knowledge capture for the Space Station Freedom. Tools are demonstrated and extended which helps automate and document engineering trade studies, and another tool is being developed to help designers interactively explore design alternatives and constraints.

Radical “Visual Capture” Observed in a Patient with Severe Visual Agnosia

PubMed Central

Takaiwa, Akiko; Yoshimura, Hirokazu; Abe, Hirofumi; Terai, Satoshi

2003-01-01

We report the case of a 79-year-old female with visual agnosia due to brain infarction in the left posterior cerebral artery. She could recognize objects used in daily life rather well by touch (the number of objects correctly identified was 16 out of 20 presented objects), but she could not recognize them as well by vision (6 out of 20). In this case, it was expected that she would recognize them well when permitted to use touch and vision simultaneously. Our patient, however, performed poorly, producing 5 correct answers out of 20 in the Vision-and-Touch condition. It would be natural to think that visual capture functions when vision and touch provide contradictory information on concrete positions and shapes. However, in the present case, it functioned in spite of the visual deficit in recognizing objects. This should be called radical visual capture. By presenting detailed descriptions of her symptoms and neuropsychological and neuroradiological data, we clarify the characteristics of this type of capture. PMID:12719638

Nucleic acid sequence detection using multiplexed oligonucleotide PCR

DOEpatents

Nolan, John P [Santa Fe, NM; White, P Scott [Los Alamos, NM

2006-12-26

Methods for rapidly detecting single or multiple sequence alleles in a sample nucleic acid are described. Provided are all of the oligonucleotide pairs capable of annealing specifically to a target allele and discriminating among possible sequences thereof, and ligating to each other to form an oligonucleotide complex when a particular sequence feature is present (or, alternatively, absent) in the sample nucleic acid. The design of each oligonucleotide pair permits the subsequent high-level PCR amplification of a specific amplicon when the oligonucleotide complex is formed, but not when the oligonucleotide complex is not formed. The presence or absence of the specific amplicon is used to detect the allele. Detection of the specific amplicon may be achieved using a variety of methods well known in the art, including without limitation, oligonucleotide capture onto DNA chips or microarrays, oligonucleotide capture onto beads or microspheres, electrophoresis, and mass spectrometry. Various labels and address-capture tags may be employed in the amplicon detection step of multiplexed assays, as further described herein.

Dual Source Time-of-flight Mass Spectrometer and Sample Handling System

NASA Astrophysics Data System (ADS)

Brinckerhoff, W.; Mahaffy, P.; Cornish, T.; Cheng, A.; Gorevan, S.; Niemann, H.; Harpold, D.; Rafeek, S.; Yucht, D.

We present details of an instrument under development for potential NASA missions to planets and small bodies. The instrument comprises a dual ionization source (laser and electron impact) time-of-flight mass spectrometer (TOF-MS) and a carousel sam- ple handling system for in situ analysis of solid materials acquired by, e.g., a coring drill. This DSTOF instrument could be deployed on a fixed lander or a rover, and has an open design that would accommodate measurements by additional instruments. The sample handling system (SHS) is based on a multi-well carousel, originally de- signed for Champollion/DS4. Solid samples, in the form of drill cores or as loose chips or fines, are inserted through an access port, sealed in vacuum, and transported around the carousel to a pyrolysis cell and/or directly to the TOF-MS inlet. Samples at the TOF-MS inlet are xy-addressable for laser or optical microprobe. Cups may be ejected from their holders for analyzing multiple samples or caching them for return. Samples are analyzed with laser desorption and evolved-gas/electron-impact sources. The dual ion source permits studies of elemental, isotopic, and molecular composition of unprepared samples with a single mass spectrometer. Pulsed laser desorption per- mits the measurement of abundance and isotope ratios of refractory elements, as well as the detection of high-mass organic molecules in solid samples. Evolved gas analysis permits similar measurements of the more volatile species in solids and aerosols. The TOF-MS is based on previous miniature prototypes at JHU/APL that feature high sensitivity and a wide mass range. The laser mode, in which the sample cup is directly below the TOF-MS inlet, permits both ablation and desorption measurements, to cover elemental and molecular species, respectively. In the evolved gas mode, sample cups are raised into a small pyrolysis cell and heated, producing a neutral gas that is elec- tron ionized and pulsed into the TOF-MS. (Any imaging and laser microprobe studies would necessarily precede the pyrolysis step to assure that the grain-scale composition is captured.)

78 FR 57654 - Proposed Information Collection; Research Permit and Reporting System Applications and Reports

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-19

...: Individuals; businesses; academic and research institutions; and Federal, State, local, and tribal governments....NM0000] Proposed Information Collection; Research Permit and Reporting System Applications and Reports... 2.5 provide for taking of scientific research specimens in parks. We use a permit system to manage...

Image acquisition system for traffic monitoring applications

NASA Astrophysics Data System (ADS)

Auty, Glen; Corke, Peter I.; Dunn, Paul; Jensen, Murray; Macintyre, Ian B.; Mills, Dennis C.; Nguyen, Hao; Simons, Ben

1995-03-01

An imaging system for monitoring traffic on multilane highways is discussed. The system, named Safe-T-Cam, is capable of operating 24 hours per day in all but extreme weather conditions and can capture still images of vehicles traveling up to 160 km/hr. Systems operating at different remote locations are networked to allow transmission of images and data to a control center. A remote site facility comprises a vehicle detection and classification module (VCDM), an image acquisition module (IAM) and a license plate recognition module (LPRM). The remote site is connected to the central site by an ISDN communications network. The remote site system is discussed in this paper. The VCDM consists of a video camera, a specialized exposure control unit to maintain consistent image characteristics, and a 'real-time' image processing system that processes 50 images per second. The VCDM can detect and classify vehicles (e.g. cars from trucks). The vehicle class is used to determine what data should be recorded. The VCDM uses a vehicle tracking technique to allow optimum triggering of the high resolution camera of the IAM. The IAM camera combines the features necessary to operate consistently in the harsh environment encountered when imaging a vehicle 'head-on' in both day and night conditions. The image clarity obtained is ideally suited for automatic location and recognition of the vehicle license plate. This paper discusses the camera geometry, sensor characteristics and the image processing methods which permit consistent vehicle segmentation from a cluttered background allowing object oriented pattern recognition to be used for vehicle classification. The image capture of high resolution images and the image characteristics required for the LPRMs automatic reading of vehicle license plates, is also discussed. The results of field tests presented demonstrate that the vision based Safe-T-Cam system, currently installed on open highways, is capable of producing automatic classification of vehicle class and recording of vehicle numberplates with a success rate around 90 percent in a period of 24 hours.

MODIFIED PATH METHODOLOGY FOR OBTAINING INTERVAL-SCALED POSTURAL ASSESSMENTS OF FARMWORKERS.

PubMed

Garrison, Emma B; Dropkin, Jonathan; Russell, Rebecca; Jenkins, Paul

2018-01-29

Agricultural workers perform tasks that frequently require awkward and extreme postures that are associated with musculoskeletal disorders (MSDs). The PATH (Posture, Activity, Tools, Handling) system currently provides a sound methodology for quantifying workers' exposure to these awkward postures on an ordinal scale of measurement, which places restrictions on the choice of analytic methods. This study reports a modification of the PATH methodology that instead captures these postures as degrees of flexion, an interval-scaled measurement. Rather than making live observations in the field, as in PATH, the postural assessments were performed on photographs using ImageJ photo analysis software. Capturing the postures in photographs permitted more careful measurement of the degrees of flexion. The current PATH methodology requires that the observer in the field be trained in the use of PATH, whereas the single photographer used in this modification requires only sufficient training to maintain the proper camera angle. Ultimately, these interval-scale measurements could be combined with other quantitative measures, such as those produced by electromyograms (EMGs), to provide more sophisticated estimates of future risk for MSDs. Further, these data can provide a baseline from which the effects of interventions designed to reduce hazardous postures can be calculated with greater precision. Copyright© by the American Society of Agricultural Engineers.

Progress in characterizing submonolayer island growth: Capture-zone distributions, growth exponents, & hot precursors

NASA Astrophysics Data System (ADS)

Einstein, Theodore L.; Pimpinelli, Alberto; González, Diego Luis; Morales-Cifuentes, Josue R.

2015-09-01

In studies of epitaxial growth, analysis of the distribution of the areas of capture zones (i.e. proximity polygons or Voronoi tessellations with respect to island centers) is often the best way to extract the critical nucleus size i. For non-random nucleation the normalized areas s of these Voronoi cells are well described by the generalized Wigner distribution (GWD) Pβ(s) = asβ exp(-bs2), particularly in the central region 0.5 < s < 2 where data are least noisy. Extensive Monte Carlo simulations reveal inadequacies of our earlier mean field analysis, suggesting β = i + 2 for diffusion-limited aggregation (DLA). Since simulations generate orders of magnitude more data than experiments, they permit close examination of the tails of the distribution, which differ from the simple GWD form. One refinement is based on a fragmentation model. We also compare island-size distributions. We compare analysis by island-size distribution and by scaling of island density with flux. Modifications appear for attach-limited aggregation (ALA). We focus on the experimental system para-hexaphenyl on amorphous mica, comparing the results of the three analysis techniques and reconciling their results via a novel model of hot precursors based on rate equations, pointing out the existence of intermediate scaling regimes between DLA and ALA.

Investigations of potential bias in the estimation of lambda using Pradel's (1996) model for capture-recapture data

USGS Publications Warehouse

Hines, J.E.; Nichols, J.D.

2002-01-01

Pradel's (1996) temporal symmetry model permitting direct estimation and modelling of population growth rate, lambda sub i provides a potentially useful tool for the study of population dynamics using marked animals. Because of its recent publication date, the approach has not seen much use, and there have been virtually no investigations directed at robustness of the resulting estimators. Here we consider several potential sources of bias, all motivated by specific uses of this estimation approach. We consider sampling situations in which the study area expands with time and present an analytic expression for the bias in lambda hat sub i. We next consider trap response in capture probabilities and heterogeneous capture probabilities and compute large-sample and simulation-based approximations of resulting bias in lambda hat sub i. These approximations indicate that trap response is an especially important assumption violation that can produce substantial bias. Finally, we consider losses on capture and emphasize the importance of selecting the estimator for lambda sub i that is appropriate to the question being addressed. For studies based on only sighting and resighting data, Pradel's (1996) lambda hat prime sub i is the appropriate estimator.

Hybrid asymptotic-numerical approach for estimating first-passage-time densities of the two-dimensional narrow capture problem.

PubMed

Lindsay, A E; Spoonmore, R T; Tzou, J C

2016-10-01

A hybrid asymptotic-numerical method is presented for obtaining an asymptotic estimate for the full probability distribution of capture times of a random walker by multiple small traps located inside a bounded two-dimensional domain with a reflecting boundary. As motivation for this study, we calculate the variance in the capture time of a random walker by a single interior trap and determine this quantity to be comparable in magnitude to the mean. This implies that the mean is not necessarily reflective of typical capture times and that the full density must be determined. To solve the underlying diffusion equation, the method of Laplace transforms is used to obtain an elliptic problem of modified Helmholtz type. In the limit of vanishing trap sizes, each trap is represented as a Dirac point source that permits the solution of the transform equation to be represented as a superposition of Helmholtz Green's functions. Using this solution, we construct asymptotic short-time solutions of the first-passage-time density, which captures peaks associated with rapid capture by the absorbing traps. When numerical evaluation of the Helmholtz Green's function is employed followed by numerical inversion of the Laplace transform, the method reproduces the density for larger times. We demonstrate the accuracy of our solution technique with a comparison to statistics obtained from a time-dependent solution of the diffusion equation and discrete particle simulations. In particular, we demonstrate that the method is capable of capturing the multimodal behavior in the capture time density that arises when the traps are strategically arranged. The hybrid method presented can be applied to scenarios involving both arbitrary domains and trap shapes.

30 CFR 778.17 - Permit term.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR LEGAL, FINANCIAL, COMPLIANCE, AND RELATED INFORMATION § 778.17 Permit...

76 FR 19975 - Proposed Information Collection; Comment Request; Survey of Building and Zoning Permit Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-11

... local building permit officials needed for updating the universe of permit-issuing places. The questions... issued. The universe of permit-issuing places is the sampling frame for the Building Permits Survey (BPS...

Research on structural integration of thermodynamic system for double reheat coal-fired unit with CO2 capture

NASA Astrophysics Data System (ADS)

Wang, Lanjing; Shao, Wenjing; Wang, Zhiyue; Fu, Wenfeng; Zhao, Wensheng

2018-02-01

Taking the MEA chemical absorption carbon capture system with 85% of the carbon capture rate of a 660MW ultra-super critical unit as an example,this paper puts forward a new type of turbine which dedicated to supply steam to carbon capture system. The comparison of the thermal systems of the power plant under different steam supply schemes by using the EBSILON indicated optimal extraction scheme for Steam Extraction System in Carbon Capture System. The results show that the cycle heat efficiency of the unit introduced carbon capture turbine system is higher than that of the usual scheme without it. With the introduction of the carbon capture turbine, the scheme which extracted steam from high pressure cylinder’ s steam input point shows the highest cycle thermal efficiency. Its indexes are superior to other scheme, and more suitable for existing coal-fired power plant integrated post combustion carbon dioxide capture system.

The other side of the broken window: a methodology that translates building permits into an ecometric of investment by community members.

PubMed

O'Brien, Daniel Tumminelli; Montgomery, Barrett W

2015-03-01

Much research has focused on physical disorder in urban neighborhoods as evidence that the community does not maintain local norms and spaces. Little attention has been paid to the opposite: indicators of proactive investment in the neighborhood's upkeep. This manuscript presents a methodology that translates a database of approved building permits into an ecometric of investment by community members, establishing basic content, criteria for reliability, and construct validity. A database from Boston, MA contained 150,493 permits spanning 2.5 years, each record including the property to be modified, permit type, and date issued. Investment was operationalized as the proportion of properties in a census block group that underwent an addition or renovation, excluding larger developments involving the demolition or construction of a building. The reliability analysis found that robust measures could be generated every 6 months, and that longitudinal analysis could differentiate between trajectories across neighborhoods. The validity analysis supported two hypotheses: investment was best predicted by homeownership and median income; and maintained an independent relationship with measures of physical disorder despite controlling for demographics, implying that it captures the other end of a spectrum of neighborhood maintenance. Possible uses for the measure in research and policy are discussed.

40 CFR 63.9322 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2011 CFR

2011-07-01

... capture system efficiency? 63.9322 Section 63.9322 Protection of Environment ENVIRONMENTAL PROTECTION... capture system efficiency? You must use the procedures and test methods in this section to determine capture efficiency as part of the performance test required by § 63.9310. (a) Assuming 100 percent capture...

40 CFR 63.9322 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... capture system efficiency? 63.9322 Section 63.9322 Protection of Environment ENVIRONMENTAL PROTECTION... capture system efficiency? You must use the procedures and test methods in this section to determine capture efficiency as part of the performance test required by § 63.9310. (a) Assuming 100 percent capture...

40 CFR 63.3554 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2011 CFR

2011-07-01

... system efficiency? 63.3554 Section 63.3554 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Requirements for the Control Efficiency/outlet Concentration Option § 63.3554 How do I determine the emission capture system efficiency? The capture efficiency of your emission capture system must be 100 percent to...

40 CFR 63.3554 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... system efficiency? 63.3554 Section 63.3554 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Requirements for the Control Efficiency/outlet Concentration Option § 63.3554 How do I determine the emission capture system efficiency? The capture efficiency of your emission capture system must be 100 percent to...

76 FR 59660 - Proposed Information Collection; Comment Request; Permitting, Vessel Identification, and Vessel...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration Proposed Information Collection; Comment Request; Permitting, Vessel Identification, and Vessel Monitoring System Requirements for... satellite- based vessel monitoring system (VMS). This collection of information is needed for permit...

And the first one now will later be last: Time-reversal in cormack-jolly-seber models

USGS Publications Warehouse

Nichols, James D.

2016-01-01

The models of Cormack, Jolly and Seber (CJS) are remarkable in providing a rich set of inferences about population survival, recruitment, abundance and even sampling probabilities from a seemingly limited data source: a matrix of 1's and 0's reflecting animal captures and recaptures at multiple sampling occasions. Survival and sampling probabilities are estimated directly in CJS models, whereas estimators for recruitment and abundance were initially obtained as derived quantities. Various investigators have noted that just as standard modeling provides direct inferences about survival, reversing the time order of capture history data permits direct modeling and inference about recruitment. Here we review the development of reverse-time modeling efforts, emphasizing the kinds of inferences and questions to which they seem well suited.

Variational coarse-graining procedure for dynamic homogenization

NASA Astrophysics Data System (ADS)

Liu, Chenchen; Reina, Celia

2017-07-01

We present a variational coarse-graining framework for heterogeneous media in the spirit of FE2 methods, that allows for a seamless transition from the traditional static scenario to dynamic loading conditions, while being applicable to general material behavior as well as to discrete or continuous representations of the material and its deformation, e.g., finite element discretizations or atomistic systems. The method automatically delivers the macroscopic equations of motion together with the generalization of Hill's averaging relations to the dynamic setting. These include the expression of the macroscopic stresses and linear momentum as a function of the microscopic fields. We further demonstrate with a proof of concept example, that the proposed theoretical framework can be used to perform multiscale numerical simulations. The results are compared with standard single-scale finite element simulations, showcasing the capability of the method to capture the dispersive nature of the medium in the range of frequencies permitted by the multiscale strategy.

Video enhancement workbench: an operational real-time video image processing system

NASA Astrophysics Data System (ADS)

Yool, Stephen R.; Van Vactor, David L.; Smedley, Kirk G.

1993-01-01

Video image sequences can be exploited in real-time, giving analysts rapid access to information for military or criminal investigations. Video-rate dynamic range adjustment subdues fluctuations in image intensity, thereby assisting discrimination of small or low- contrast objects. Contrast-regulated unsharp masking enhances differentially shadowed or otherwise low-contrast image regions. Real-time removal of localized hotspots, when combined with automatic histogram equalization, may enhance resolution of objects directly adjacent. In video imagery corrupted by zero-mean noise, real-time frame averaging can assist resolution and location of small or low-contrast objects. To maximize analyst efficiency, lengthy video sequences can be screened automatically for low-frequency, high-magnitude events. Combined zoom, roam, and automatic dynamic range adjustment permit rapid analysis of facial features captured by video cameras recording crimes in progress. When trying to resolve small objects in murky seawater, stereo video places the moving imagery in an optimal setting for human interpretation.

Jellium Hydride

NASA Astrophysics Data System (ADS)

Bonev, Stanimir; Ashcroft, Neil W.

2000-03-01

We have studied a system of protons (with compensating additional electrons) embedded in a previously neutral electron gas (the standard jellium problem) at densities corresponding to rs = 0.8 - 3.4. This expands on the study of a single proton in an interacting electron gas(C.O. Almbladh, U. von Barth, Z.D. Popovic, and M.J. Scott, Phys. Rev. B \\underline14), 2250 (1976), and in particular, it permits a detailed study of a proton pairing in a many-electron environment. Ab initio (LSDA) simulations show the appearance of a bond proton-pair at rs >= 3.2 and with a dimer length R ≈ 1.5 a_0. At larger separations, the preferred state is a pair of H^- - like ions, i.e. electrons are captured from jellium. This is in accordance with an analysis of the situation where the charge surrounding a proton is determined jointly by the cusp condition and linear response.

A Role Calculus for ORM

NASA Astrophysics Data System (ADS)

Curland, Matthew; Halpin, Terry; Stirewalt, Kurt

A conceptual schema of an information system specifies the fact structures of interest as well as related business rules that are either constraints or derivation rules. Constraints restrict the possible or permitted states or state transitions, while derivation rules enable some facts to be derived from others. Graphical languages are commonly used to specify conceptual schemas, but often need to be supplemented by more expressive textual languages to capture additional business rules, as well as conceptual queries that enable conceptual models to be queried directly. This paper describes research to provide a role calculus to underpin textual languages for Object-Role Modeling (ORM), to enable business rules and queries to be formulated in a language intelligible to business users. The role-based nature of this calculus, which exploits the attribute-free nature of ORM, appears to offer significant advantages over other proposed approaches, especially in the area of semantic stability.

NPDES Permit for Air Force Academy Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Under NPDES permit CO-R042007, the U.S. Air Force Academy is authorized to discharge from all municipal separate storm sewer system outfalls to the receiving waters specified in the permit in El Paso County, Colorado.

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

Using the Statecharts paradigm for simulation of patient flow in surgical care.

PubMed

Sobolev, Boris; Harel, David; Vasilakis, Christos; Levy, Adrian

2008-03-01

Computer simulation of patient flow has been used extensively to assess the impacts of changes in the management of surgical care. However, little research is available on the utility of existing modeling techniques. The purpose of this paper is to examine the capacity of Statecharts, a system of graphical specification, for constructing a discrete-event simulation model of the perioperative process. The Statecharts specification paradigm was originally developed for representing reactive systems by extending the formalism of finite-state machines through notions of hierarchy, parallelism, and event broadcasting. Hierarchy permits subordination between states so that one state may contain other states. Parallelism permits more than one state to be active at any given time. Broadcasting of events allows one state to detect changes in another state. In the context of the peri-operative process, hierarchy provides the means to describe steps within activities and to cluster related activities, parallelism provides the means to specify concurrent activities, and event broadcasting provides the means to trigger a series of actions in one activity according to transitions that occur in another activity. Combined with hierarchy and parallelism, event broadcasting offers a convenient way to describe the interaction of concurrent activities. We applied the Statecharts formalism to describe the progress of individual patients through surgical care as a series of asynchronous updates in patient records generated in reaction to events produced by parallel finite-state machines representing concurrent clinical and managerial activities. We conclude that Statecharts capture successfully the behavioral aspects of surgical care delivery by specifying permissible chronology of events, conditions, and actions.

41 CFR 301-71.303 - What data must we capture in our travel advance accounting system?

Code of Federal Regulations, 2010 CFR

2010-07-01

... capture in our travel advance accounting system? 301-71.303 Section 301-71.303 Public Contracts and Property Management Federal Travel Regulation System TEMPORARY DUTY (TDY) TRAVEL ALLOWANCES AGENCY... must we capture in our travel advance accounting system? You must capture the following data: (a) The...

40 CFR 122.43 - Establishing permit conditions (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Permit Conditions § 122.43 Establishing permit conditions (applicable to State...

40 CFR 122.43 - Establishing permit conditions (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Permit Conditions § 122.43 Establishing permit conditions (applicable to State...

Biochar as enhancement material in natural attenuation systems

NASA Astrophysics Data System (ADS)

Kirmizakis, P.; Doherty, R.; Mendonça, C. A.; Costeira, R.; Allen, C.; Kulakov, L.

2017-12-01

Bioelectrochemical systems (BESs) have gained increasingly popularity over the last years especially in monitoring and clean-up of contaminants. BES are systems that combine wastewater treatment with energy production and resource recovery by harness the electro-activity of microorganisms. BESs consist of two electrodes, an anode and a cathode, separated with a proton-exchange membrane and an external electrical circuit which permits the passage of electrons generated at the anode to the cathode. Here we present a speed up of this natural breakdown process by providing a place to capture the anaerobic contaminants onto Biochar which captures the contaminants and also acts like a high surface area electrode passing electrons to the aerobic environments. For the purpose of this project, identical graphite and Teflon cells were constructed to compare and determine whether a Biochar BES was more efficient than a standard BES and more efficient than Biochar as sorption agent. Current production monitoring used as a real-time view of the process. The Biochar BES out performed both the BES and the Biochar BES in reduction of contaminants across the board. Our results suggest that the maximum growth and electro-activity of the microbial community occurred in the Biochar BES. This is in agreement with microbial findings which suggests that Biochar BES has a less diverse population which is more focused towards degradation and electroactive activity. For further understanding of the results, further geochemical analysis performed to provide additional insight on the process. This works shows clearly the applicability and efficiency of biochar among other electrode and sorption materials and electrical monitoring is versatile experimental tool to the remediation process and can be used as a non-destructive way to indirectly reveal process leading in understanding basic fundamental physical behaviours under specific experimental conditions.

NPDES Permit for Denver VA Hospital Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Under NPDES permit CO-R042008, the Veterans Administration (Medical Center, Denver Campus) is authorized to discharge from all municipal separate storm sewer system outfalls to the receiving waters specified in the permit in the City of Denver, Colorado.

A continuous analyzer for soluble anionic constituents and ammonium in atmospheric particulate matter.

PubMed

Al-Horr, Rida; Samanta, Gautam; Dasgupta, Purnendu K

2003-12-15

A new continuous soluble particle collector (PC) that does not use steam is described. Preceded by a denuder and interfaced with an ion chromatograph, this compact collector (3 in. o.d., approximately 5 in. total height) permits collection and continuous extraction of soluble components in atmospheric particulate matter. The PC is mounted atop a parallel plate wetted denuder for removal of soluble gases. The soluble gas denuded air enters the PC through an inlet. One version of the PC contained an integral cyclone-like inlet. For this device, penetration of particles as a function of size was characterized. In the simpler design, the sampled air enters the PC through a nozzle, and deionized water flows through a capillary tube placed close to the exit side of the nozzle by Venturi action or is forcibly pumped. Some growth of the aerosol occurs in the highly humid mist-chamber environment, but the dominant aerosol capture mechanism involves capture by the water film that forms on the hydrophobic PTFE membrane filter that constitutes the top of the PC and the airflow exit. Water drops coalesce on the filter and fall below into a purpose-machined cavity equipped with a liquid sensor. The water and the dissolved constituents are aspirated by a pump onto serial cation and anion preconcentrator columns. NH4+ captured by the cation preconcentrator is eluted with NaOH and is passed across an asymmetric membrane device. NH3 diffuses from the alkaline donor stream into a deionized water flowing countercurrent; the conductivity of the latter provides a measure of ammonium. The anions on the anion preconcentrator column are eluted and measured by a fully automated ion chromatography system. The total system thus provides automated semicontinuous measurement of soluble anions and ammonium. With a 15 min analytical cycle and a sampling rate of 5 L/min, the limit of detection (LOD) for ammonium is 8 ng/m3 and those for sulfate, nitrate, and oxalate are < or = 0.1 ng/m3. The system has been extensively field tested.

Polarization microscopy by use of digital holography: application to optical-fiber birefringence measurements.

PubMed

Colomb, Tristan; Dürr, Florian; Cuche, Etienne; Marquet, Pierre; Limberger, Hans G; Salathé, René-Paul; Depeursinge, Christian

2005-07-20

We present a digital holographic microscope that permits one to image polarization state. This technique results from the coupling of digital holographic microscopy and polarization digital holography. The interference between two orthogonally polarized reference waves and the wave transmitted by a microscopic sample, magnified by a microscope objective, is recorded on a CCD camera. The off-axis geometry permits one to reconstruct separately from this single hologram two wavefronts that are used to image the object-wave Jones vector. We applied this technique to image the birefringence of a bent fiber. To evaluate the precision of the phase-difference measurement, the birefringence induced by internal stress in an optical fiber is measured and compared to the birefringence profile captured by a standard method, which had been developed to obtain high-resolution birefringence profiles of optical fibers.

Compressive Coded-Aperture Multimodal Imaging Systems

NASA Astrophysics Data System (ADS)

Rueda-Chacon, Hoover F.

Multimodal imaging refers to the framework of capturing images that span different physical domains such as space, spectrum, depth, time, polarization, and others. For instance, spectral images are modeled as 3D cubes with two spatial and one spectral coordinate. Three-dimensional cubes spanning just the space domain, are referred as depth volumes. Imaging cubes varying in time, spectra or depth, are referred as 4D-images. Nature itself spans different physical domains, thus imaging our real world demands capturing information in at least 6 different domains simultaneously, giving turn to 3D-spatial+spectral+polarized dynamic sequences. Conventional imaging devices, however, can capture dynamic sequences with up-to 3 spectral channels, in real-time, by the use of color sensors. Capturing multiple spectral channels require scanning methodologies, which demand long time. In general, to-date multimodal imaging requires a sequence of different imaging sensors, placed in tandem, to simultaneously capture the different physical properties of a scene. Then, different fusion techniques are employed to mix all the individual information into a single image. Therefore, new ways to efficiently capture more than 3 spectral channels of 3D time-varying spatial information, in a single or few sensors, are of high interest. Compressive spectral imaging (CSI) is an imaging framework that seeks to optimally capture spectral imagery (tens of spectral channels of 2D spatial information), using fewer measurements than that required by traditional sensing procedures which follows the Shannon-Nyquist sampling. Instead of capturing direct one-to-one representations of natural scenes, CSI systems acquire linear random projections of the scene and then solve an optimization algorithm to estimate the 3D spatio-spectral data cube by exploiting the theory of compressive sensing (CS). To date, the coding procedure in CSI has been realized through the use of ``block-unblock" coded apertures, commonly implemented as chrome-on-quartz photomasks. These apertures block or permit to pass the entire spectrum from the scene at given spatial locations, thus modulating the spatial characteristics of the scene. In the first part, this thesis aims to expand the framework of CSI by replacing the traditional block-unblock coded apertures by patterned optical filter arrays, referred as ``color" coded apertures. These apertures are formed by tiny pixelated optical filters, which in turn, allow the input image to be modulated not only spatially but spectrally as well, entailing more powerful coding strategies. The proposed colored coded apertures are either synthesized through linear combinations of low-pass, high-pass and band-pass filters, paired with binary pattern ensembles realized by a digital-micromirror-device (DMD), or experimentally realized through thin-film color-patterned filter arrays. The optical forward model of the proposed CSI architectures will be presented along with the design and proof-of-concept implementations, which achieve noticeable improvements in the quality of the reconstructions compared with conventional block-unblock coded aperture-based CSI architectures. On another front, due to the rich information contained in the infrared spectrum as well as the depth domain, this thesis aims to explore multimodal imaging by extending the range sensitivity of current CSI systems to a dual-band visible+near-infrared spectral domain, and also, it proposes, for the first time, a new imaging device that captures simultaneously 4D data cubes (2D spatial+1D spectral+depth imaging) with as few as a single snapshot. Due to the snapshot advantage of this camera, video sequences are possible, thus enabling the joint capture of 5D imagery. It aims to create super-human sensing that will enable the perception of our world in new and exciting ways. With this, we intend to advance in the state of the art in compressive sensing systems to extract depth while accurately capturing spatial and spectral material properties. The applications of such a sensor are self-evident in fields such as computer/robotic vision because they would allow an artificial intelligence to make informed decisions about not only the location of objects within a scene but also their material properties.

76 FR 22444 - Privacy Act; System of Records: State-52, Parking Permit and Car Pool Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-21

... and Car Pool Records Summary: Notice is hereby given that the Department of State proposes to amend an existing system of records, Parking Permit and Car Pool Records, State-52, pursuant to the provisions of... 29, 2011. It is proposed that the current system will retain the name ``Parking Permit and Car Pool...

36 CFR 222.3 - Issuance of grazing and livestock use permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be authorized without written permit. (F) Paid or free permits for horses, mules, or burros to...) Free permits for horses, mules, or burros to cooperators who clearly need National Forest System land...

36 CFR 222.3 - Issuance of grazing and livestock use permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... be authorized without written permit. (F) Paid or free permits for horses, mules, or burros to...) Free permits for horses, mules, or burros to cooperators who clearly need National Forest System land...

36 CFR 222.3 - Issuance of grazing and livestock use permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... be authorized without written permit. (F) Paid or free permits for horses, mules, or burros to...) Free permits for horses, mules, or burros to cooperators who clearly need National Forest System land...

40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.3546 Section 63... of key parameters of the valve operating system (e.g., solenoid valve operation, air pressure... minimum operating limit for that specific capture device or system of multiple capture devices. The...

40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.3546 Section 63... of key parameters of the valve operating system (e.g., solenoid valve operation, air pressure... minimum operating limit for that specific capture device or system of multiple capture devices. The...

76 FR 40355 - Modification to 2008 National Pollutant Discharge Elimination System (NPDES) General Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... Construction Activities AGENCY: Environmental Protection Agency (EPA). ACTION: Notice. SUMMARY: EPA Regions 1... (NPDES) general permits for stormwater discharges associated with construction activity in order to... permits will be referred to as ``permit'' or ``2008 construction general permit'' or ``2008 CGP.'' This...

40 CFR 63.7290 - What emission limitations must I meet for capture systems and control devices applied to pushing...

Code of Federal Regulations, 2014 CFR

2014-07-01

... to capture emissions; (3) If a mobile scrubber car that does not capture emissions during travel is... each capture system that uses an electric motor to drive the fan, you must maintain the daily average... (ii) For each capture system that does not use a fan driven by an electric motor, you must maintain...

40 CFR 63.7290 - What emission limitations must I meet for capture systems and control devices applied to pushing...

Code of Federal Regulations, 2013 CFR

2013-07-01

... to capture emissions; (3) If a mobile scrubber car that does not capture emissions during travel is... each capture system that uses an electric motor to drive the fan, you must maintain the daily average... (ii) For each capture system that does not use a fan driven by an electric motor, you must maintain...

40 CFR 63.7290 - What emission limitations must I meet for capture systems and control devices applied to pushing...

Code of Federal Regulations, 2012 CFR

2012-07-01

... to capture emissions; (3) If a mobile scrubber car that does not capture emissions during travel is... each capture system that uses an electric motor to drive the fan, you must maintain the daily average... (ii) For each capture system that does not use a fan driven by an electric motor, you must maintain...

40 CFR 63.7290 - What emission limitations must I meet for capture systems and control devices applied to pushing...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to capture emissions; (3) If a mobile scrubber car that does not capture emissions during travel is... each capture system that uses an electric motor to drive the fan, you must maintain the daily average... (ii) For each capture system that does not use a fan driven by an electric motor, you must maintain...

40 CFR 63.7290 - What emission limitations must I meet for capture systems and control devices applied to pushing...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to capture emissions; (3) If a mobile scrubber car that does not capture emissions during travel is... each capture system that uses an electric motor to drive the fan, you must maintain the daily average... (ii) For each capture system that does not use a fan driven by an electric motor, you must maintain...

Percutaneous Epicardial Pacing using a Novel Insulated Multi-electrode Lead.

PubMed

Syed, Faisal F; DeSimone, Christopher V; Ebrille, Elisa; Gaba, Prakriti; Ladewig, Dorothy J; Mikell, Susan B; Suddendorf, Scott H; Gilles, Emily J; Danielsen, Andrew J; Lukášová, Markéta; Wolf, Jiří; Leinveber, Pavel; Novák, Miroslav; Stárek, Zdeněk; Kara, Tomas; Bruce, Charles J; Friedman, Paul A; Asirvatham, Samuel J

2015-08-01

Epicardial cardiac resynchronization therapy (CRT) permits unrestricted electrode positioning. However, this requires surgical placement of device leads and the risk of unwanted phrenic nerve stimulation. We hypothesized that shielded electrodes can capture myocardium without extracardiac stimulation. In 6 dog and 5 swine experiments, we used a percutaneous approach to access the epicardial surface of the heart, and deploy novel leads housing multiple electrodes with selective insulation. Bipolar pacing thresholds at prespecified sites were tested compare electrode threshold data both facing towards and away from the epicardial surface. In 151 paired electrode recordings (70 in 6 dogs; 81 in 5 swine), thresholds facing myocardium were lower than facing away (median [IQR] mA: dogs 0.9 [0.4-1.6] vs 4.6 [2.1 to >10], p<0.0001; swine 0.5 [0.2-1] vs 2.5 [0.5-6.8], p<0.0001). Myocardial capture was feasible without extracardiac stimulation at all tested sites, with mean ± SE threshold margin 3.6±0.7 mA at sites of high output extracardiac stimulation (p=0.004). Selective electrode insulation confers directional pacing to a multielectrode epicardial pacing lead. This device has the potential for a novel percutaneous epicardial resynchronization therapy that permits placement at an optimal pacing site, irrespective of the anatomy of the coronary veins or phrenic nerves.

Effects of flooding of the River Paraná on the temporal activity of Anopheles (Nyssorhynchus) darlingi Root (Diptera: Culicidae), at the border state of Mato Grosso do Sul and São Paulo, Brazil.

PubMed

Gomes, Almério de Castro; Paula, Marcia Bicudo de; Natal, Delsio; Gotlieb, Sabina Léa Davidson; Mucci, Luis Filipe

2010-01-01

Study of the temporal activity of malaria vectors during the implantation of a hydroelectric power station on the River Paraná, intended to generate electrical energy. The river separates the States of São Paulo and Mato Grosso do Sul, in Brazil. The objective was to verify whether alterations occurred in the wealth and diversity indices of Anopheles, following two successive floods, extended to the temporal activity and nycthemeral rhythm followed over a five year period. Mosquito capture was performed monthly using the Human Attraction Technique and Shannon Traps. The first, executed for 24h, provided the nycthemeral rhythm and the second, lasting 15 h, permitted the tracking of Anopheles during the two floods. The bimodal pattern of Anopheles darlingi defined before these floods was modified throughout the environment interventions. The same effect had repercussions on the populations of An albitarsis s.l., An triannulatus and An galvaoi. Activity prior to twilight was less affected by the environment alterations. The dam construction provoked changes in Anopheles temporal activity patterns, permitting classification of the area as an ecologically steady and unstable situation. Differences observed in Anopheles behavior due to the capture methods revealed the influence of solo and multiple attractiveness inside the populations studied.

40 CFR 122.46 - Duration of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Permit Conditions § 122.46 Duration of permits (applicable to State programs, see § 123.25...

The Effectiveness of Classroom Capture Technology

ERIC Educational Resources Information Center

Ford, Maire B.; Burns, Colleen E.; Mitch, Nathan; Gomez, Melissa M.

2012-01-01

The use of classroom capture systems (systems that capture audio and video footage of a lecture and attempt to replicate a classroom experience) is becoming increasingly popular at the university level. However, research on the effectiveness of classroom capture systems in the university classroom has been limited due to the recent development and…

Integrated System Health Management: Pilot Operational Implementation in a Rocket Engine Test Stand

NASA Technical Reports Server (NTRS)

Figueroa, Fernando; Schmalzel, John L.; Morris, Jonathan A.; Turowski, Mark P.; Franzl, Richard

2010-01-01

This paper describes a credible implementation of integrated system health management (ISHM) capability, as a pilot operational system. Important core elements that make possible fielding and evolution of ISHM capability have been validated in a rocket engine test stand, encompassing all phases of operation: stand-by, pre-test, test, and post-test. The core elements include an architecture (hardware/software) for ISHM, gateways for streaming real-time data from the data acquisition system into the ISHM system, automated configuration management employing transducer electronic data sheets (TEDS?s) adhering to the IEEE 1451.4 Standard for Smart Sensors and Actuators, broadcasting and capture of sensor measurements and health information adhering to the IEEE 1451.1 Standard for Smart Sensors and Actuators, user interfaces for management of redlines/bluelines, and establishment of a health assessment database system (HADS) and browser for extensive post-test analysis. The ISHM system was installed in the Test Control Room, where test operators were exposed to the capability. All functionalities of the pilot implementation were validated during testing and in post-test data streaming through the ISHM system. The implementation enabled significant improvements in awareness about the status of the test stand, and events and their causes/consequences. The architecture and software elements embody a systems engineering, knowledge-based approach; in conjunction with object-oriented environments. These qualities are permitting systematic augmentation of the capability and scaling to encompass other subsystems.

NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM PERMITS FOR NORTH CAROLINA PORTION OF ALBEMARLE-PAMLICO ESTUARY

EPA Science Inventory

Excel spreadsheet of National Pollutant Discharge Elimination System (NPDES) permits as of 4/2000 for the Albemarle-Pamlico Estuary watershed. Permitted flow is in millions of gallons per day. Discharge codes are:
1 Domestic - Municipal
2 Domestic - Industrial/Commercial

76 FR 48184 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-08

... developed regulations for the establishment of a permit system for various activities in Antarctica and... establish such a permit system to designate Antarctic Specially Protected Areas. The applications received... established in 1986 studying the foraging ecology, population dynamics, census and reproductive success and...

36 CFR 222.4 - Changes in grazing permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RANGE MANAGEMENT Grazing and Livestock Use on the National Forest System § 222.4 Changes in grazing... use permits in whole or in part as follows: (1) Cancel permits where lands grazed under the permit are... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Changes in grazing permits...

Separable Bilayer Microfiltration Device for Viable Label-free Enrichment of Circulating Tumour Cells

NASA Astrophysics Data System (ADS)

Zhou, Ming-Da; Hao, Sijie; Williams, Anthony J.; Harouaka, Ramdane A.; Schrand, Brett; Rawal, Siddarth; Ao, Zheng; Brennaman, Randall; Gilboa, Eli; Lu, Bo; Wang, Shuwen; Zhu, Jiyue; Datar, Ram; Cote, Richard; Tai, Yu-Chong; Zheng, Si-Yang

2014-12-01

The analysis of circulating tumour cells (CTCs) in cancer patients could provide important information for therapeutic management. Enrichment of viable CTCs could permit performance of functional analyses on CTCs to broaden understanding of metastatic disease. However, this has not been widely accomplished. Addressing this challenge, we present a separable bilayer (SB) microfilter for viable size-based CTC capture. Unlike other single-layer CTC microfilters, the precise gap between the two layers and the architecture of pore alignment result in drastic reduction in mechanical stress on CTCs, capturing them viably. Using multiple cancer cell lines spiked in healthy donor blood, the SB microfilter demonstrated high capture efficiency (78-83%), high retention of cell viability (71-74%), high tumour cell enrichment against leukocytes (1.7-2 × 103), and widespread ability to establish cultures post-capture (100% of cell lines tested). In a metastatic mouse model, SB microfilters successfully enriched viable mouse CTCs from 0.4-0.6 mL whole mouse blood samples and established in vitro cultures for further genetic and functional analysis. Our preliminary studies reflect the efficacy of the SB microfilter device to efficiently and reliably enrich viable CTCs in animal model studies, constituting an exciting technology for new insights in cancer research.

Sequence capture by hybridization to explore modern and ancient genomic diversity in model and nonmodel organisms

PubMed Central

Gasc, Cyrielle; Peyretaillade, Eric

2016-01-01

Abstract The recent expansion of next-generation sequencing has significantly improved biological research. Nevertheless, deep exploration of genomes or metagenomic samples remains difficult because of the sequencing depth and the associated costs required. Therefore, different partitioning strategies have been developed to sequence informative subsets of studied genomes. Among these strategies, hybridization capture has proven to be an innovative and efficient tool for targeting and enriching specific biomarkers in complex DNA mixtures. It has been successfully applied in numerous areas of biology, such as exome resequencing for the identification of mutations underlying Mendelian or complex diseases and cancers, and its usefulness has been demonstrated in the agronomic field through the linking of genetic variants to agricultural phenotypic traits of interest. Moreover, hybridization capture has provided access to underexplored, but relevant fractions of genomes through its ability to enrich defined targets and their flanking regions. Finally, on the basis of restricted genomic information, this method has also allowed the expansion of knowledge of nonreference species and ancient genomes and provided a better understanding of metagenomic samples. In this review, we present the major advances and discoveries permitted by hybridization capture and highlight the potency of this approach in all areas of biology. PMID:27105841

Synthetic, switchable enzymes

PubMed Central

Norris, Vic; Krylov, Sergey N.; Agarwal, Pratul K.; White, Glenn J.

2017-01-01

The construction of switchable, radiation-controlled, aptameric enzymes alias swenzymes is, in principle, feasible. We propose a strategy to make such catalysts from two (or more) aptamers each selected to bind specifically to one of the substrates in, for example, a two-substrate reaction. Construction of a combinatorial library of candidate swenzymes entails selecting a set of a million aptamers that bind one substrate and a second set of a million aptamers that bind the second substrate; the aptamers in these sets are then linked pairwise by a linker so bringing together the substrates. In the presence of the substrates, some linked aptamer pairs catalyze the reaction when exposed to external energy in the form of a specific frequency of low intensity, non-ionizing electromagnetic or acoustic radiation. Such swenzymes are detected via a separate, product-capturing, aptamer that changes conformation on capturing the product; this altered conformation allows it (1) to bind to every potential swenzyme in its vicinity (thereby giving a higher probability of capture to the swenzymes that generate the product) and (2) to bind to a sequence on a magnetic bead (thereby permitting purification of the swenzyme plus product-capturing aptamer by precipitation). Attempts to implement the swenzyme strategy may help elucidate fundamental problems in enzyme catalysis. PMID:28448969

Synthetic, Switchable Enzymes.

PubMed

Norris, Vic; Krylov, Sergey N; Agarwal, Pratul K; White, Glenn J

2017-01-01

The construction of switchable, radiation-controlled, aptameric enzymes - "swenzymes" - is, in principle, feasible. We propose a strategy to make such catalysts from 2 (or more) aptamers each selected to bind specifically to one of the substrates in, for example, a 2-substrate reaction. Construction of a combinatorial library of candidate swenzymes entails selecting a set of a million aptamers that bind one substrate and a second set of a million aptamers that bind the second substrate; the aptamers in these sets are then linked pairwise by a linker, thus bringing together the substrates. In the presence of the substrates, some linked aptamer pairs catalyze the reaction when exposed to external energy in the form of a specific frequency of low-intensity, nonionizing electromagnetic or acoustic radiation. Such swenzymes are detected via a separate product-capturing aptamer that changes conformation on capturing the product; this altered conformation allows it (1) to bind to every potential swenzyme in its vicinity (thereby giving a higher probability of capture to the swenzymes that generate the product) and (2) to bind to a sequence on a magnetic bead (thereby permitting purification of the swenzyme plus product-capturing aptamer by precipitation). Attempts to implement the swenzyme strategy may help elucidate fundamental problems in enzyme catalysis. © 2017 S. Karger AG, Basel.

Sequence capture by hybridization to explore modern and ancient genomic diversity in model and nonmodel organisms.

PubMed

Gasc, Cyrielle; Peyretaillade, Eric; Peyret, Pierre

2016-06-02

The recent expansion of next-generation sequencing has significantly improved biological research. Nevertheless, deep exploration of genomes or metagenomic samples remains difficult because of the sequencing depth and the associated costs required. Therefore, different partitioning strategies have been developed to sequence informative subsets of studied genomes. Among these strategies, hybridization capture has proven to be an innovative and efficient tool for targeting and enriching specific biomarkers in complex DNA mixtures. It has been successfully applied in numerous areas of biology, such as exome resequencing for the identification of mutations underlying Mendelian or complex diseases and cancers, and its usefulness has been demonstrated in the agronomic field through the linking of genetic variants to agricultural phenotypic traits of interest. Moreover, hybridization capture has provided access to underexplored, but relevant fractions of genomes through its ability to enrich defined targets and their flanking regions. Finally, on the basis of restricted genomic information, this method has also allowed the expansion of knowledge of nonreference species and ancient genomes and provided a better understanding of metagenomic samples. In this review, we present the major advances and discoveries permitted by hybridization capture and highlight the potency of this approach in all areas of biology. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Learner Performance Accounting: A Tri-Cycle Process

ERIC Educational Resources Information Center

Brown, Thomas C.; McCleary, Lloyd E.

1973-01-01

The Tri-Cycle Process described in the model permits for the first time an integrated system for designing an individualized instructional system that would permit a rational, diagnosis-prescription-evaluation system keyed to an accounting system. (Author)

Detection of target staphylococcal enterotoxin B antigen in orange juice and popular carbonated beverages using antibody-dependent antigen-capture assays.

PubMed

Principato, MaryAnn; Njoroge, Joyce M; Perlloni, Andrei; O' Donnell, Michael; Boyle, Thomas; Jones, Robert L

2010-10-01

There is a critical need for qualitative and quantitative methodologies that provide the rapid and accurate detection of food contaminants in complex food matrices. However, the sensitivity of the assay can be affected when antigen-capture is applied to certain foods or beverages that are extremely acidic. This study was undertaken to assess the effects of orange juice and popular carbonated soft drink upon the fidelity of antibody-based antigen-capture assays and to develop simple approaches that could rescue assay performance without the introduction of additional or extensive extraction procedures. We examined the effects of orange juice and a variety of popular carbonated soft drink beverages upon a quantitative Interleukin-2 (IL-2) enzyme-linked immunosorbent assay (ELISA) assay system and a lateral flow device (LFD) adapted for the detection of staphylococcal enterotoxin B (SEB) in foods. Alterations in the performance and sensitivity of the assay were directly attributable to the food matrix, and alterations in pH were especially critical. The results demonstrate that approaches such as an alteration of pH and the use of milk as a blocking agent, either singly or in combination, will partially rescue ELISA performance. The same approaches permit lateral flow to efficiently detect antigen. Practical Application: The authors present ways to rescue an ELISA assay compromised by acidity in beverages and show that either the alteration of pH, or the use of milk as a blocking agent are not always capable of restoring the assay to its intended efficiency. However, the same methods, when employed with lateral flow technology, are rapid and extremely successful.

Three-dimensional light trap for reflective particles

DOEpatents

Neal, Daniel R.

1999-01-01

A system for containing either a reflective particle or a particle having an index of refraction lower than that of the surrounding media in a three-dimensional light cage. A light beam from a single source illuminates an optics system and generates a set of at least three discrete focussed beams that emanate from a single exit aperture and focus on to a focal plane located close to the particle. The set of focal spots defines a ring that surrounds the particle. The set of focussed beams creates a "light cage" and circumscribes a zone of no light within which the particle lies. The surrounding beams apply constraining forces (created by radiation pressure) to the particle, thereby containing it in a three-dimensional force field trap. A diffractive element, such as an aperture multiplexed lens, or either a Dammann grating or phase element in combination with a focusing lens, may be used to generate the beams. A zoom lens may be used to adjust the size of the light cage, permitting particles of various sizes to be captured and contained.

Three-dimensional light trap for reflective particles

DOEpatents

Neal, D.R.

1999-08-17

A system is disclosed for containing either a reflective particle or a particle having an index of refraction lower than that of the surrounding media in a three-dimensional light cage. A light beam from a single source illuminates an optics system and generates a set of at least three discrete focused beams that emanate from a single exit aperture and focus on to a focal plane located close to the particle. The set of focal spots defines a ring that surrounds the particle. The set of focused beams creates a ``light cage`` and circumscribes a zone of no light within which the particle lies. The surrounding beams apply constraining forces (created by radiation pressure) to the particle, thereby containing it in a three-dimensional force field trap. A diffractive element, such as an aperture multiplexed lens, or either a Dammann grating or phase element in combination with a focusing lens, may be used to generate the beams. A zoom lens may be used to adjust the size of the light cage, permitting particles of various sizes to be captured and contained. 10 figs.

76 FR 53763 - Immigration Benefits Business Transformation, Increment I

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-29

...The Department of Homeland Security (DHS) is amending its regulations to enable U.S. Citizenship and Immigration Services (USCIS) to migrate from a paper file-based, non-integrated systems environment to an electronic customer-focused, centralized case management environment for benefit processing. This transformation process will allow USCIS to streamline benefit processing, eliminate the capture and processing of redundant data, and reduce the number of and automate its forms. This transformation process will be a phased multi-year initiative to restructure USCIS business processes and related information technology systems. DHS is removing references to form numbers, form titles, expired regulatory provisions, and descriptions of internal procedures, many of which will change during transformation. DHS is also finalizing interim rules that permitted submission of benefit requests with an electronic signature when such requests are submitted in an electronic format rather than on a paper form and that removed references to filing locations for immigration benefits. In addition, in this rule DHS is publishing the final rule for six other interim rules published during the past several years, most of which received no public comments.

A Low-Cost Digital Microscope with Real-Time Fluorescent Imaging Capability.

PubMed

Hasan, Md Mehedi; Alam, Mohammad Wajih; Wahid, Khan A; Miah, Sayem; Lukong, Kiven Erique

2016-01-01

This paper describes the development of a prototype of a low-cost digital fluorescent microscope built from commercial off-the-shelf (COTS) components. The prototype was tested to detect malignant tumor cells taken from a living organism in a preclinical setting. This experiment was accomplished by using Alexa Fluor 488 conjugate dye attached to the cancer cells. Our prototype utilizes a torch along with an excitation filter as a light source for fluorophore excitation, a dichroic mirror to reflect the excitation and pass the emitted green light from the sample under test and a barrier filter to permit only appropriate wavelength. The system is designed out of a microscope using its optical zooming property and an assembly of exciter filter, dichroic mirror and transmitter filter. The microscope is connected to a computer or laptop through universal serial bus (USB) that allows real-time transmission of captured florescence images; this also offers real-time control of the microscope. The designed system has comparable features of high-end commercial fluorescent microscopes while reducing cost, power, weight and size.

A Low-Cost Digital Microscope with Real-Time Fluorescent Imaging Capability

PubMed Central

Hasan, Md. Mehedi; Wahid, Khan A.; Miah, Sayem; Lukong, Kiven Erique

2016-01-01

This paper describes the development of a prototype of a low-cost digital fluorescent microscope built from commercial off-the-shelf (COTS) components. The prototype was tested to detect malignant tumor cells taken from a living organism in a preclinical setting. This experiment was accomplished by using Alexa Fluor 488 conjugate dye attached to the cancer cells. Our prototype utilizes a torch along with an excitation filter as a light source for fluorophore excitation, a dichroic mirror to reflect the excitation and pass the emitted green light from the sample under test and a barrier filter to permit only appropriate wavelength. The system is designed out of a microscope using its optical zooming property and an assembly of exciter filter, dichroic mirror and transmitter filter. The microscope is connected to a computer or laptop through universal serial bus (USB) that allows real-time transmission of captured florescence images; this also offers real-time control of the microscope. The designed system has comparable features of high-end commercial fluorescent microscopes while reducing cost, power, weight and size. PMID:27977709

Economic and energetic analysis of capturing CO2 from ambient air

PubMed Central

House, Kurt Zenz; Baclig, Antonio C.; Ranjan, Manya; van Nierop, Ernst A.; Wilcox, Jennifer; Herzog, Howard J.

2011-01-01

Capturing carbon dioxide from the atmosphere (“air capture”) in an industrial process has been proposed as an option for stabilizing global CO2 concentrations. Published analyses suggest these air capture systems may cost a few hundred dollars per tonne of CO2, making it cost competitive with mainstream CO2 mitigation options like renewable energy, nuclear power, and carbon dioxide capture and storage from large CO2 emitting point sources. We investigate the thermodynamic efficiencies of commercial separation systems as well as trace gas removal systems to better understand and constrain the energy requirements and costs of these air capture systems. Our empirical analyses of operating commercial processes suggest that the energetic and financial costs of capturing CO2 from the air are likely to have been underestimated. Specifically, our analysis of existing gas separation systems suggests that, unless air capture significantly outperforms these systems, it is likely to require more than 400 kJ of work per mole of CO2, requiring it to be powered by CO2-neutral power sources in order to be CO2 negative. We estimate that total system costs of an air capture system will be on the order of $1,000 per tonne of CO2, based on experience with as-built large-scale trace gas removal systems. PMID:22143760

40 CFR 63.3965 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

...; coating solvent flash-off, curing, and drying occurs within the capture system; and the removal or... spray booth and a curing oven. (b) Measuring capture efficiency. If the capture system does not meet... surface preparation activities and drying and curing time. (c) Liquid-to-uncaptured-gas protocol using a...

NPDES (National Pollution Discharge & Elimination System) Minor Dischargers

EPA Pesticide Factsheets

As authorized by the Clean Water Act, the National Pollutant Discharge Elimination System (NPDES) permit program controls water pollution by regulating point sources that discharge pollutants into waters of the United States. The NPDES permit program regulates direct discharges from municipal and industrial wastewater treatment facilities that discharge directly into surface waters. The NPDES permit program is part of the Permit Compliance System (PCS) which issues, records, tracks, and regulates point source discharge facilities. Individual homes that are connected to a municipal system, use a septic system, or do not have a surface discharge do not need an NPDES permit. Facilities in PCS are identified as either major or minor. Within the major/minor classification, facilities are grouped into municipals or non-municipals. In many cases, non-municipals are industrial facilities. This data layer contains Minor dischargers. Major municipal dischargers include all facilities with design flows of greater than one million gallons per day; minor dischargers are less that one million gallons per day. Essentially, a minor discharger does not meet the discharge criteria for a major. Since its introduction in 1972, the NPDES permit program is responsible for significant improvements to our Nation's water quality.

Streamline, Organizational, Legislative and Administrative Response to Permitting, PV Market Share, and Solar Energy Costs (Broward Go SOLAR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halsey, Jeffery D.

2013-08-28

Broward County and its partners (the Go SOLAR Team), operating under a Department of Energy Rooftop Solar Challenge Agreement, designed, developed and implemented an online permitting system for rooftop solar PV systems. This is a single web based system with a single permit fee that will issue a permit, with a set of design plans preapproved by partner building officials, within one hour. The system is currently available at gosolar.broward.org for use within any of the partner Authorities Having [permitting] Jurisdiction (AHJ). Additionally, the Go SOLAR Team researched, developed and to the extent feasible, implemented three best management practices tomore » make a fertile environment for the new online permit system. These included Net Metering and Interconnection Standards, Solar-Friendly Financing, and Planning and Zoning Ordinances. Finally, the team implemented a substantial outreach effort to advocate for the development of solar in Broward County, with an emphasis on Solar Rights, concluding with a Go SOLAR Fest day and a half conference with over 1,200 attendees and 50 exhibitors. The Go SOLAR project was completed on time, under DOE’s budgeted amount, and all project objectives were met or exceeded.« less

Mining the Mind Research Network: A Novel Framework for Exploring Large Scale, Heterogeneous Translational Neuroscience Research Data Sources

PubMed Central

Bockholt, Henry J.; Scully, Mark; Courtney, William; Rachakonda, Srinivas; Scott, Adam; Caprihan, Arvind; Fries, Jill; Kalyanam, Ravi; Segall, Judith M.; de la Garza, Raul; Lane, Susan; Calhoun, Vince D.

2009-01-01

A neuroinformatics (NI) system is critical to brain imaging research in order to shorten the time between study conception and results. Such a NI system is required to scale well when large numbers of subjects are studied. Further, when multiple sites participate in research projects organizational issues become increasingly difficult. Optimized NI applications mitigate these problems. Additionally, NI software enables coordination across multiple studies, leveraging advantages potentially leading to exponential research discoveries. The web-based, Mind Research Network (MRN), database system has been designed and improved through our experience with 200 research studies and 250 researchers from seven different institutions. The MRN tools permit the collection, management, reporting and efficient use of large scale, heterogeneous data sources, e.g., multiple institutions, multiple principal investigators, multiple research programs and studies, and multimodal acquisitions. We have collected and analyzed data sets on thousands of research participants and have set up a framework to automatically analyze the data, thereby making efficient, practical data mining of this vast resource possible. This paper presents a comprehensive framework for capturing and analyzing heterogeneous neuroscience research data sources that has been fully optimized for end-users to perform novel data mining. PMID:20461147

Simulation of load-sharing in standalone distributed generation system

NASA Astrophysics Data System (ADS)

Ajewole, Titus O.; Craven, Robert P. M.; Kayode, Olakunle; Babalola, Olufisayo S.

2018-05-01

This paper presents a study on load-sharing among the component generating units of a multi-source electric microgrid that is operated as an autonomous ac supply-mode system. Emerging trend in power system development permits deployment of microgrids for standalone or stand-by applications, thereby requiring active- and reactive power sharing among the discrete generating units contained in hybrid-source microgrids. In this study, therefore, a laboratory-scale model of a microgrid energized with three renewable energy-based sources is employed as a simulation platform to investigate power sharing among the power-generating units. Each source is represented by a source emulator that captures the real operational characteristics of the mimicked generating unit and, with implementation of real-life weather data and load profiles on the model; the sharing of the load among the generating units is investigated. There is a proportionate generation of power by the three source emulators, with their frequencies perfectly synchronized at the point of common coupling as a result of balance flow of power among them. This hybrid topology of renewable energy-based microgrid could therefore be seamlessly adapted into national energy mix by the indigenous electric utility providers in Nigeria.

78 FR 70075 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978 (Public Law...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-22

... establishment of a permit system for various activities in Antarctica and designation of certain animals and certain geographic areas a requiring special protection. The regulations establish such a permit system to..., stable isotope analysis, and DNA extraction. Data would be used to reconstruct seal population dynamics...

77 FR 28897 - Notice of Lodging of Consent Decree Under the Clean Water Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

...'s violation of the National Pollution Discharge Elimination System Permit (``NPDES Permit'') for its... its wastewater treatment system that will enable it to comply with the permit, which include upgrading... Department of Justice Web site: http://www.usdoj.gov/enrd/Consent_Decrees.html . A copy of the Consent Decree...

Study on data acquisition system based on reconfigurable cache technology

NASA Astrophysics Data System (ADS)

Zhang, Qinchuan; Li, Min; Jiang, Jun

2018-03-01

Waveform capture rate is one of the key features of digital acquisition systems, which represents the waveform processing capability of the system in a unit time. The higher the waveform capture rate is, the larger the chance to capture elusive events is and the more reliable the test result is. First, this paper analyzes the impact of several factors on the waveform capture rate of the system, then the novel technology based on reconfigurable cache is further proposed to optimize system architecture, and the simulation results show that the signal-to-noise ratio of signal, capacity, and structure of cache have significant effects on the waveform capture rate. Finally, the technology is demonstrated by the engineering practice, and the results show that the waveform capture rate of the system is improved substantially without significant increase of system's cost, and the technology proposed has a broad application prospect.

The Impact of City-level Permitting Processes on Residential Photovoltaic Installation Prices and Development Times: An Empirical Analysis of Solar Systems in California Cities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiser, Ryan; Dong, Changgui

Business process or “soft” costs account for well over 50% of the installed price of residential photovoltaic (PV) systems in the United States, so understanding these costs is crucial for identifying PV cost-reduction opportunities. Among these costs are those imposed by city-level permitting processes, which may add both expense and time to the PV development process. Building on previous research, this study evaluates the effect of city-level permitting processes on the installed price of residential PV systems and on the time required to develop and install those systems. The study uses a unique dataset from the U.S. Department of Energy’smore » Rooftop Solar Challenge Program, which includes city-level permitting process “scores,” plus data from the California Solar Initiative and the U.S. Census. Econometric methods are used to quantify the price and development-time effects of city-level permitting processes on more than 3,000 PV installations across 44 California cities in 2011. Results indicate that city-level permitting processes have a substantial and statistically significant effect on average installation prices and project development times. The results suggest that cities with the most favorable (i.e., highest-scoring) permitting practices can reduce average residential PV prices by $0.27–$0.77/W (4%–12% of median PV prices in California) compared with cities with the most onerous (i.e., lowest-scoring) permitting practices, depending on the regression model used. Though the empirical models for development times are less robust, results suggest that the most streamlined permitting practices may shorten development times by around 24 days on average (25% of the median development time). These findings illustrate the potential price and development-time benefits of streamlining local permitting procedures for PV systems.« less

30 CFR 778.12 - Providing permit history information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR LEGAL, FINANCIAL, COMPLIANCE, AND RELATED...

Characteristics of Cometary Dust Tracks in Stardust Aerogel and Laboratory Calibrations

NASA Technical Reports Server (NTRS)

Burchell, M. J.; Fairey, S. A. J.; Wozniakiewicz, P.; Brownlee, D. E.; Hoerz, F.; Kearsley, A. T.; See, T. H.; Tsou, P.; Westphal, A.; Green, S. F.;

Spallation processes and nuclear interaction products of cosmic rays.

PubMed

Silberberg, R; Tsao, C H

1990-08-01

Most cosmic-ray nuclei heavier than helium have suffered nuclear collisions in the interstellar gas, with transformation of nuclear composition. The isotopic and elemental composition at the sources has to be inferred from the observed composition near the Earth. The source composition permits tests of current ideas on sites of origin, nucleosynthesis in stars, evolution of stars, the mixing and composition of the interstellar medium and injection processes prior to acceleration. The effects of nuclear spallation, production of radioactive nuclides and the time dependence of their decay provide valuable information on the acceleration and propagation of cosmic rays, their nuclear transformations, and their confinement time in the Galaxy. The formation of spallation products that only decay by electron capture and are relatively long-lived permits an investigation of the nature and density fluctuations (like clouds) of the interstellar medium. Since nuclear collisions yield positrons, antiprotons, gamma rays and neutrinos, we shall discuss these topics briefly.

Wilderness Management... A Computerized System for Summarizing Permit Information

Treesearch

Gary H. Elsner

1972-01-01

Permits were first needed for visits to wilderness areas in California during summer 1971. A computerized system for analyzing these permits and summarizing information from them has been developed. It produces four types of summary tables: point-of-origin of visitors; daily variation in total number of persons present; variations in group size; and variations in...

75 FR 57299 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978 (Pub. L. 95-541)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-20

... Antarctic Conservation Act of 1978 (Pub. L. 95-541), as amended by the Antarctic Science, Tourism and Conservation Act of 1996, has developed regulations for the establishment of a permit system for various... protection. The regulations establish such a permit system to designate Antarctic Specially Protected Areas...

76 FR 61117 - Notice of Permit Applications Received Under the Antarctic Conservation Act of 1978 (Pub. L. 95-541)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-03

... Antarctic Conservation Act of 1978 (Pub. L. 95-541), as amended by the Antarctic Science, Tourism and Conservation Act of 1996, has developed regulations for the establishment of a permit system for various... protection. The regulations establish such a permit system to designate Antarctic Specially Protected Areas...

Grande Ronde Basin Chinook Salmon Captive Brood and Conventional Supplementation Programs, 2002 Annual Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carmichael, Richard W.

2003-07-01

Endangered Species Permit Number 1011 (formerly Permit No. 973) authorizes ODFW to take listed spring chinook salmon juveniles from Catherine Creek (CC), Lostine River (LR) and Grande Ronde River (GR) for research and enhancement purposes. Modification 2 of this permit authorizes ODFW to take adults for spawning and the production and release of smolts for the Captive and Conventional broodstock programs. This report satisfies the requirement that an annual report be submitted. Herein we report on activities conducted and provide cursory data analyses for the Grande Ronde spring chinook salmon Captive and Conventional broodstock projects from 1 January-31 December 2002.more » The Grande Ronde Basin Spring Chinook Salmon Captive Broodstock Project is designed to rapidly increase numbers of salmon in stocks that are in imminent danger of extirpation. Parr are captured in Catherine Creek, upper Grande Ronde River and Lostine River and reared to adulthood in captivity. Upon maturation, they are spawned (within stocks) and their progeny reared to smoltification before being released into the natal stream of their parents. This program is co-managed by ODFW, National Marine Fisheries Service, the Nez Perce Tribe and Confederated Tribes of the Umatilla Indian Reservation.« less

40 CFR 122.46 - Duration of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Duration of permits (applicable to... ELIMINATION SYSTEM Permit Conditions § 122.46 Duration of permits (applicable to State programs, see § 123.25... in § 122.6, the term of a permit shall not be extended by modification beyond the maximum duration...

Systems planning for automated commercial vehicle licensing and permitting systems : national ITS/CVO program requirements

DOT National Transportation Integrated Search

1997-07-01

This report describes the work of the study, Systems Planning for Automated Commercial Vehicle Licensing and Permitting Systems. The objective of this study is to define the market, organization, and resource requirements for a national program...

Systems Analysis of Physical Absorption of CO2 in Ionic Liquids for Pre-Combustion Carbon Capture.

PubMed

Zhai, Haibo; Rubin, Edward S

2018-04-17

This study develops an integrated technical and economic modeling framework to investigate the feasibility of ionic liquids (ILs) for precombustion carbon capture. The IL 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide is modeled as a potential physical solvent for CO 2 capture at integrated gasification combined cycle (IGCC) power plants. The analysis reveals that the energy penalty of the IL-based capture system comes mainly from the process and product streams compression and solvent pumping, while the major capital cost components are the compressors and absorbers. On the basis of the plant-level analysis, the cost of CO 2 avoided by the IL-based capture and storage system is estimated to be $63 per tonne of CO 2 . Technical and economic comparisons between IL- and Selexol-based capture systems at the plant level show that an IL-based system could be a feasible option for CO 2 capture. Improving the CO 2 solubility of ILs can simplify the capture process configuration and lower the process energy and cost penalties to further enhance the viability of this technology.

40 CFR 70.8 - Permit review by EPA and affected States.

Code of Federal Regulations, 2013 CFR

2013-07-01

... compatible with EPA's national database management system. (2) The Administrator may waive the requirements...) Transmission of information to the Administrator. (1) The permit program shall require that the permitting authority provide to the Administrator a copy of each permit application (including any application for...

40 CFR 70.8 - Permit review by EPA and affected States.

Code of Federal Regulations, 2014 CFR

2014-07-01

... compatible with EPA's national database management system. (2) The Administrator may waive the requirements...) Transmission of information to the Administrator. (1) The permit program shall require that the permitting authority provide to the Administrator a copy of each permit application (including any application for...

40 CFR 70.8 - Permit review by EPA and affected States.

Code of Federal Regulations, 2010 CFR

2010-07-01

... compatible with EPA's national database management system. (2) The Administrator may waive the requirements...) Transmission of information to the Administrator. (1) The permit program shall require that the permitting authority provide to the Administrator a copy of each permit application (including any application for...

40 CFR 70.8 - Permit review by EPA and affected States.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compatible with EPA's national database management system. (2) The Administrator may waive the requirements...) Transmission of information to the Administrator. (1) The permit program shall require that the permitting authority provide to the Administrator a copy of each permit application (including any application for...

40 CFR 70.8 - Permit review by EPA and affected States.

Code of Federal Regulations, 2012 CFR

2012-07-01

... compatible with EPA's national database management system. (2) The Administrator may waive the requirements...) Transmission of information to the Administrator. (1) The permit program shall require that the permitting authority provide to the Administrator a copy of each permit application (including any application for...

40 CFR 122.45 - Calculating NPDES permit conditions (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Permit Conditions § 122.45 Calculating NPDES permit conditions..., and prohibitions, including those necessary to achieve water quality standards, shall unless...

EPA's Draft 2017 Construction General Permit (CGP)

EPA Pesticide Factsheets

EPA is preparing to reissue the Construction General Permit (CGP). The general permit, issued under the Clean Water Act's National Pollutant Discharge Elimination System, authorizes stormwater discharges from construction activities.

Advances in analysis of pre-earthquake thermal anomalies by analyzing IR satellite data

NASA Astrophysics Data System (ADS)

Ouzounov, D.; Bryant, N.; Filizzola, C.; Pergola, N.; Taylor, P.; Tramutoli, V.

Presented work addresses the possible relationship between tectonic stress, electro-chemical and thermodynamic processes in the atmosphere and increasing infrared (IR) flux as part of a larger family of electromagnetic (EM) phenomena related to earthquake activity. Thermal infra-red (TIR) surveys performed by polar orbiting (NOAA/AVHRR, MODIS) and geosynchronous weather satellites (GOES, METEOSAT) seems to indicate the appearance (from days to weeks before the event) of "anomalous" space-time TIR transients associated with the place (epicentral area, linear structures and fault systems) and the time of occurrence of a number of major earthquakes with M>5 and focal depths no deeper than 50km. As Earth emitted in 8-14 microns range the TIR signal measured from satellite strongly vary depending on meteorological conditions and other factors (space-time changes in atmospheric transmittance, time/season, solar and satellite zenithal angles and etc) independent from seismic activity, a preliminary definition of "anomalous TIR signal" should be given. To provide reliable discrimination of thermal anomalous area from the natural events (seasonal changes, local morphology) new robust approach (RAT) has been recently proposed (and successfully applied in the field of the monitoring of the major environmental risks) that permits to give a statistically based definition of thermal info-red (TIR) anomaly and reduce of false events detection. New techniques also were specifically developed to assure the precise co-registration of all satellite scenes and permit accurate time-series analysis of satellite observations. As final results we present examples of most recent 2000/2004 worldwide strong earthquakes and the techniques used to capture the tracks of thermal emission mid-IR anomalies and methodology for practical future use of such phenomena in the early warning systems.

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

30 CFR 784.24 - Road systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Road systems. 784.24 Section 784.24 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS... systems. (a) Plans and drawings. Each applicant for an underground coal mining and reclamation permit...

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

30 CFR 784.24 - Road systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Road systems. 784.24 Section 784.24 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS... systems. (a) Plans and drawings. Each applicant for an underground coal mining and reclamation permit...

30 CFR 780.37 - Road systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Road systems. 780.37 Section 780.37 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.37 Road systems...

30 CFR 784.24 - Road systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Road systems. 784.24 Section 784.24 Mineral... MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS... systems. (a) Plans and drawings. Each applicant for an underground coal mining and reclamation permit...

System and process for capture of H.sub.2S from gaseous process streams and process for regeneration of the capture agent

DOEpatents

Heldenbrant, David J; Koech, Phillip K; Rainbolt, James E; Bearden, Mark D; Zheng, Feng

2014-02-18

A system and process are disclosed for selective removal and recovery of H.sub.2S from a gaseous volume, e.g., from natural gas. Anhydrous organic, sorbents chemically capture H.sub.2S gas to form hydrosulfide salts. Regeneration of the capture solvent involves addition of an anti-solvent that releases the captured H.sub.2S gas from the capture sorbent. The capture sorbent and anti-solvent are reactivated for reuse, e.g., by simple distillation.

36 CFR 13.934 - How will the superintendent manage the permit program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... manage the permit program? 13.934 Section 13.934 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Denali National Park and Preserve Motor Vehicle Permits § 13.934 How will the superintendent manage the permit...

36 CFR 13.934 - How will the superintendent manage the permit program?

Code of Federal Regulations, 2014 CFR

2014-07-01

... manage the permit program? 13.934 Section 13.934 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Denali National Park and Preserve Motor Vehicle Permits § 13.934 How will the superintendent manage the permit...

36 CFR 13.934 - How will the superintendent manage the permit program?

Code of Federal Regulations, 2011 CFR

2011-07-01

... manage the permit program? 13.934 Section 13.934 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Denali National Park and Preserve Motor Vehicle Permits § 13.934 How will the superintendent manage the permit...

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... from the web coating/printing operation surfaces they are applied to occurs within the capture system... system efficiency? 63.4361 Section 63.4361 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... emission capture system efficiency? You must use the procedures and test methods in this section to...

Estimating temporary emigration and breeding proportions using capture-recapture data with Pollock's robust design

USGS Publications Warehouse

Kendall, W.L.; Nichols, J.D.; Hines, J.E.

1997-01-01

Statistical inference for capture-recapture studies of open animal populations typically relies on the assumption that all emigration from the studied population is permanent. However, there are many instances in which this assumption is unlikely to be met. We define two general models for the process of temporary emigration, completely random and Markovian. We then consider effects of these two types of temporary emigration on Jolly-Seber (Seber 1982) estimators and on estimators arising from the full-likelihood approach of Kendall et al. (1995) to robust design data. Capture-recapture data arising from Pollock's (1982) robust design provide the basis for obtaining unbiased estimates of demographic parameters in the presence of temporary emigration and for estimating the probability of temporary emigration. We present a likelihood-based approach to dealing with temporary emigration that permits estimation under different models of temporary emigration and yields tests for completely random and Markovian emigration. In addition, we use the relationship between capture probability estimates based on closed and open models under completely random temporary emigration to derive three ad hoc estimators for the probability of temporary emigration, two of which should be especially useful in situations where capture probabilities are heterogeneous among individual animals. Ad hoc and full-likelihood estimators are illustrated for small mammal capture-recapture data sets. We believe that these models and estimators will be useful for testing hypotheses about the process of temporary emigration, for estimating demographic parameters in the presence of temporary emigration, and for estimating probabilities of temporary emigration. These latter estimates are frequently of ecological interest as indicators of animal movement and, in some sampling situations, as direct estimates of breeding probabilities and proportions.

Review of the High Performance Antiproton Trap (HiPAT) Experiment at the Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Pearson, J. B.; Sims, Herb; Martin, James; Chakrabarti, Suman; Lewis, Raymond; Fant, Wallace

2003-01-01

The significant energy density of matter-antimatter annihilation is attractive to the designers of future space propulsion systems, with the potential to offer a highly compact source of power. Many propulsion concepts exist that could take advantage of matter-antimatter reactions, and current antiproton production rates are sufficient to support basic proof-of-principle evaluation of technology associated with antimatter- derived propulsion. One enabling technology for such experiments is portable storage of low energy antiprotons, allowing antiprotons to be trapped, stored, and transported for use at an experimental facility. To address this need, the Marshall Space Flight Center's Propulsion Research Center is developing a storage system referred to as the High Performance Antiproton Trap (HiPAT) with a design goal of containing 10(exp 12) particles for up to 18 days. The HiPAT makes use of an electromagnetic system (Penning- Malmberg design) consisting of a 4 Telsa superconductor, high voltage electrode structure, radio frequency (RF) network, and ultra high vacuum system. To evaluate the system normal matter sources (both electron guns and ion sources) are used to generate charged particles. The electron beams ionize gas within the trapping region producing ions in situ, whereas the ion sources produce the particles external to the trapping region and required dynamic capture. A wide range of experiments has been performed examining factors such as ion storage lifetimes, effect of RF energy on storage lifetime, and ability to routinely perform dynamic ion capture. Current efforts have been focused on improving the FW rotating wall system to permit longer storage times and non-destructive diagnostics of stored ions. Typical particle detection is performed by extracting trapped ions from HiPAT and destructively colliding them with a micro-channel plate detector (providing number and energy information). This improved RF system has been used to detect various plasma modes for both electron and ion plasmas in the two traps at MSFC, including axial, cyclotron, and diocotron modes. New diagnostics are also being added to HiPAT to measure the axial density distribution of the trapped cloud to match measured RF plasma modes to plasma conditions.

Privacy-preserving screen capture: towards closing the loop for health IT usability.

PubMed

Cooley, Joseph; Smith, Sean

2013-08-01

As information technology permeates healthcare (particularly provider-facing systems), maximizing system effectiveness requires the ability to document and analyze tricky or troublesome usage scenarios. However, real-world health IT systems are typically replete with privacy-sensitive data regarding patients, diagnoses, clinicians, and EMR user interface details; instrumentation for screen capture (capturing and recording the scenario depicted on the screen) needs to respect these privacy constraints. Furthermore, real-world health IT systems are typically composed of modules from many sources, mission-critical and often closed-source; any instrumentation for screen capture can rely neither on access to structured output nor access to software internals. In this paper, we present a tool to help solve this problem: a system that combines keyboard video mouse (KVM) capture with automatic text redaction (and interactively selectable unredaction) to produce precise technical content that can enrich stakeholder communications and improve end-user influence on system evolution. KVM-based capture makes our system both application-independent and OS-independent because it eliminates software-interface dependencies on capture targets. Using a corpus of EMR screenshots, we present empirical measurements of redaction effectiveness and processing latency to demonstrate system performances. We discuss how these techniques can translate into instrumentation systems that improve real-world health IT deployments. Copyright © 2013 Elsevier Inc. All rights reserved.

Diagnosing added value of convection-permitting regional models using precipitation event identification and tracking

NASA Astrophysics Data System (ADS)

Chang, W.; Wang, J.; Marohnic, J.; Kotamarthi, V. R.; Moyer, E. J.

2017-12-01

We use a novel rainstorm identification and tracking algorithm (Chang et al 2016) to evaluate the effects of using resolved convection on improving how faithfully high-resolution regional simulations capture precipitation characteristics. The identification and tracking algorithm allocates all precipitation to individual rainstorms, including low-intensity events with complicated features, and allows us to decompose changes or biases in total mean precipitation into their causes: event size, intensity, number, and duration. It allows lower threshold for tracking so captures nearly all rainfall and improves tracking, so that events that are clearly meteorologically related are tracked across lifespans up to days. We evaluate a series of dynamically downscaled simulations of the summertime United States at 12 and 4 km under different model configurations, and find that resolved convection offers the largest gains in reducing biases in precipitation characteristics, especially in event size. Simulations with parametrized convection produce event sizes 80-220% too large in extent; with resolved convection the bias is reduced to 30%. The identification and tracking algorithm also allows us to demonstrate that the diurnal cycle in rainfall stems not from temporal variation in the production of new events but from diurnal fluctuations in rainfall from existing events. We show further hat model errors in the diurnal cycle biases are best represented as additive offsets that differ by time of day, and again that convection-permitting simulations are most efficient in reducing these additive biases.

Automated technologies needed to prevent radioactive materials from reentering the atmosphere

NASA Astrophysics Data System (ADS)

Buden, David; Angelo, Joseph A., Jr.

Project SIREN (Search, Intercept, Retrieve, Expulsion Nuclear) has been created to identify and evaluate the technologies and operational strategies needed to rendezvous with and capture aerospace radioactive materials (e.g., a distressed or spent space reactor core) before such materials can reenter the terrestrial atmosphere and then to safely move these captured materials to an acceptable space destination for proper disposal. A major component of the current Project SIREN effort is the development of an interactive technology model (including a computerized data base) that explores in building block fashion the interaction of the technologies and procedures needed to successfully accomplish a SIREN mission. This SIREN model will include appropriate national and international technology elements-both contemporary and projected into the next century. To permit maximum flexibility and use, the SIREN technology data base is being programmed for use on 386-class PC's.

40 CFR 122.64 - Termination of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Transfer, Modification, Revocation and Reissuance, and Termination of Permits § 122.64...

40 CFR 122.61 - Transfer of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Transfer, Modification, Revocation and Reissuance, and Termination of Permits § 122.61...

40 CFR 122.64 - Termination of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Transfer, Modification, Revocation and Reissuance, and Termination of Permits § 122.64...

40 CFR 122.61 - Transfer of permits (applicable to State programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Transfer, Modification, Revocation and Reissuance, and Termination of Permits § 122.61...

A Systematic Approach for Evaluation of Capture Zones at Pump and Treat Systems

EPA Science Inventory

This document describes a systematic approach for performing capture zone analysis associated with ground water pump and treat systems. A “capture zone” refers to the three-dimensional region that contributes the ground water extracted by one or more wells or drains. A capture ...

Evaluation of Uniform Cost Accounting System to Fully Capture Depot Level Repair Costs.

DTIC Science & Technology

1985-12-01

RD-RI65 522 EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM TO FULLY i/I CAPTURE DEPOT LEVEL REPAIR COSTS (U) NAVAL POSTGRADUATE SCHOOL MONTEREY CA D R...8217.LECTE B ,- THESIS EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM 0TO FULLY CAPTURE DEPOT LEVEL REPAIR COSTS Jby __jDavid Richmond O’Brien lj,,, December...Include Security Classification) EVALUATION OF UNIFORM COST ACCOUNTING SYSTEM TO FULLY CAPTURE DEPOT LEVEL REPAIR COSTS 12 PERSONAL AUTHOR(S) O’Brien- David

Portable pathogen detection system

DOEpatents

Colston, Billy W.; Everett, Matthew; Milanovich, Fred P.; Brown, Steve B.; Vendateswaran, Kodumudi; Simon, Jonathan N.

2005-06-14

A portable pathogen detection system that accomplishes on-site multiplex detection of targets in biological samples. The system includes: microbead specific reagents, incubation/mixing chambers, a disposable microbead capture substrate, and an optical measurement and decoding arrangement. The basis of this system is a highly flexible Liquid Array that utilizes optically encoded microbeads as the templates for biological assays. Target biological samples are optically labeled and captured on the microbeads, which are in turn captured on an ordered array or disordered array disposable capture substrate and then optically read.

Wyoming's industrial siting permit process and environmental impact assessment

NASA Astrophysics Data System (ADS)

Hyman, Eric L.

1982-01-01

The problem of management of industrial residuals can be reduced through a rational system for siting and planning major industrial facilities. In the United States, Wyoming has moved in the direction of establishing a one-stop permitting system that provides important information for air and water quality planning and solid waste management with a minimum of regulatory overlap. This paper describes Wyoming's Industrial Development Information and Siting Act of 1975 and suggests ways in which the Wyoming permitting system can be improved and applied elsewhere.

A knowledge-based system design/information tool

NASA Technical Reports Server (NTRS)

Allen, James G.; Sikora, Scott E.

1990-01-01

The objective of this effort was to develop a Knowledge Capture System (KCS) for the Integrated Test Facility (ITF) at the Dryden Flight Research Facility (DFRF). The DFRF is a NASA Ames Research Center (ARC) facility. This system was used to capture the design and implementation information for NASA's high angle-of-attack research vehicle (HARV), a modified F/A-18A. In particular, the KCS was used to capture specific characteristics of the design of the HARV fly-by-wire (FBW) flight control system (FCS). The KCS utilizes artificial intelligence (AI) knowledge-based system (KBS) technology. The KCS enables the user to capture the following characteristics of automated systems: the system design; the hardware (H/W) design and implementation; the software (S/W) design and implementation; and the utilities (electrical and hydraulic) design and implementation. A generic version of the KCS was developed which can be used to capture the design information for any automated system. The deliverable items for this project consist of the prototype generic KCS and an application, which captures selected design characteristics of the HARV FCS.

Heterogeneity of envelope molecules expressed on primary human immunodeficiency virus type 1 particles as probed by the binding of neutralizing and nonneutralizing antibodies.

PubMed

Poignard, Pascal; Moulard, Maxime; Golez, Edwin; Vivona, Veronique; Franti, Michael; Venturini, Sara; Wang, Meng; Parren, Paul W H I; Burton, Dennis R

2003-01-01

Virion capture assays, in which immobilized antibodies (Abs) capture virus particles, have been used to suggest that nonneutralizing Abs bind effectively to human immunodeficiency virus type 1 (HIV-1) primary viruses. Here, we show that virion capture assays, under conditions commonly reported in the literature, give a poor indication of epitope expression on the surface of infectious primary HIV-1. First, estimation of primary HIV-1 capture by p24 measurements shows a very poor correlation with an estimation based on infectivity measurements. Second, virion capture appears to require relatively low Ab affinity for the virion, as shown by the ability of a monoclonal Ab to capture a wild-type and a neutralization escape variant virus equally well. Nevertheless, in a more interpretable competition format, it is shown that nonneutralizing anti-CD4 binding site (CD4bs) Abs compete with a neutralizing anti-CD4bs Ab (b12) for virus capture, suggesting that the nonneutralizing anti-CD4bs Abs are able to bind to the envelope species that is involved in virion capture in these experiments. However, the nonneutralizing anti-CD4bs Abs do not inhibit neutralization by b12 even at considerable excess. This suggests that the nonneutralizing Abs are unable to bind effectively to the envelope species required for virus infectivity. The results were obtained for three different primary virus envelopes. The explanation that we favor is that infectious HIV-1 primary virions can express two forms of gp120, an accessible nonfunctional form and a functional form with limited access. Binding to the nonfunctional form, which needs only to be present at relatively low density on the virion, permits capture but does not lead to neutralization. The expression of a nonfunctional but accessible form of gp120 on virions may contribute to the general failure of HIV-1 infection to elicit cross-neutralizing Abs and may represent a significant problem for vaccines based on viruses or virus-like particles.

50 CFR 665.19 - Vessel monitoring system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 13 2012-10-01 2012-10-01 false Vessel monitoring system. 665.19 Section... monitoring system. (a) Applicability. The holder of any of the following permits is subject to the vessel monitoring system requirements in this part: (1) Hawaii longline limited access permit issued pursuant to...

50 CFR 665.19 - Vessel monitoring system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 13 2013-10-01 2013-10-01 false Vessel monitoring system. 665.19 Section... monitoring system. (a) Applicability. The holder of any of the following permits is subject to the vessel monitoring system requirements in this part: (1) Hawaii longline limited access permit issued pursuant to...

50 CFR 665.19 - Vessel monitoring system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 11 2011-10-01 2011-10-01 false Vessel monitoring system. 665.19 Section... monitoring system. (a) Applicability. The holder of any of the following permits is subject to the vessel monitoring system requirements in this part: (1) Hawaii longline limited access permit issued pursuant to...

78 FR 20316 - Draft Small Municipal Separate Storm Sewer System NPDES General Permit-New Hampshire; Extension...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-04

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9799-1] Draft Small Municipal Separate Storm Sewer System NPDES General Permit--New Hampshire; Extension of Comment Period AGENCY: Environmental Protection Agency... draft Small Municipal Separate Storm Sewer System (MS4) National Pollutant Discharge Elimination System...

78 FR 27964 - Draft Small Municipal Separate Storm Sewer System NPDES General Permit-New Hampshire; Extension...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9812-8] Draft Small Municipal Separate Storm Sewer System NPDES General Permit--New Hampshire; Extension of Comment Period AGENCY: Environmental Protection Agency... draft Small Municipal Separate Storm Sewer System (MS4) National Pollutant Discharge Elimination System...

50 CFR 665.19 - Vessel monitoring system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Vessel monitoring system. 665.19 Section... monitoring system. (a) Applicability. The holder of any of the following permits is subject to the vessel monitoring system requirements in this part: (1) Hawaii longline limited access permit issued pursuant to...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinclair, Karin; DeGeorge, Elise

The Bald and Golden Eagle Protection Act (BGEPA) prohibits the 'take' of these birds. The act defines take as to 'pursue, shoot, shoot at, poison, wound, kill, capture, trap, collect, destroy, molest or disturb.' The 2009 Eagle Permit Rule (74 FR 46836) authorizes the U.S. Fish and Wildlife Service (USFWS) to issue nonpurposeful (i.e., incidental) take permits, and the USFWS 2013 Eagle Conservation Plan Guidance provides a voluntary framework for issuing programmatic take permits to wind facilities that incorporate scientifically supportable advanced conservation practices (ACPs). Under these rules, the Service can issue permits that authorize individual instances of take ofmore » bald and golden eagles when the take is associated with, but not the purpose of, an otherwise lawful activity, and cannot practicably be avoided. To date, the USFWS has not approved any ACPs, citing the lack of evidence for 'scientifically supportable measures.' The Eagle Detection and Deterrents Research Gaps and Solutions Workshop was convened at the National Renewable Energy Laboratory in December 2015 with a goal to comprehensively assess the current state of technologies to detect and deter eagles from wind energy sites and the key gaps concerning reducing eagle fatalities and facilitating permitting under the BGEPA. During the workshop, presentations and discussions focused primarily on existing knowledge (and limitations) about the biology of eagles as well as technologies and emerging or novel ideas, including innovative applications of tools developed for use in other sectors, such as the U.S. Department of Defense and aviation. The main activity of the workshop was the breakout sessions, which focused on the current state of detection and deterrent technologies and novel concepts/applications for detecting and minimizing eagle collisions with wind turbines. Following the breakout sessions, participants were asked about their individual impressions of the relative priority of each of the existing and novel ideas.« less

30 CFR 774.17 - Transfer, assignment, or sale of permit rights.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Transfer, assignment, or sale of permit rights... SYSTEMS UNDER REGULATORY PROGRAMS REVISION; RENEWAL; TRANSFER, ASSIGNMENT, OR SALE OF PERMIT RIGHTS; POST... § 774.17 Transfer, assignment, or sale of permit rights. (a) General. No transfer, assignment, or sale...

30 CFR 774.17 - Transfer, assignment, or sale of permit rights.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Transfer, assignment, or sale of permit rights... SYSTEMS UNDER REGULATORY PROGRAMS REVISION; RENEWAL; TRANSFER, ASSIGNMENT, OR SALE OF PERMIT RIGHTS; POST... § 774.17 Transfer, assignment, or sale of permit rights. (a) General. No transfer, assignment, or sale...

30 CFR 773.21 - Initial review and finding requirements for improvidently issued permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS AND PERMIT PROCESSING § 773.21 Initial review and finding requirements for improvidently issued permits. (a) If we, the regulatory authority... paragraph (c) of this section, you may challenge the preliminary finding by providing us with evidence as to...

77 FR 47380 - Final National Pollutant Discharge Elimination System (NPDES) General Permit for Discharges From...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-08

... permit. Major changes also include definition of ``operator'', acute toxicity test for produced water... Category as authorized by section 402 of the Clean Water Act, (CWA). This permit renewal authorizes... considered all comments received and makes few changes to the proposed permit: pH limit for formation test...

50 CFR 25.41 - Who issues refuge permits?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Who issues refuge permits? 25.41 Section... (CONTINUED) THE NATIONAL WILDLIFE REFUGE SYSTEM ADMINISTRATIVE PROVISIONS Permits § 25.41 Who issues refuge permits? We authorize the refuge manager of the facility where an activity is to take place to issue...

Sustainable Capture: Concepts for Managing Stream-Aquifer Systems.

PubMed

Davids, Jeffrey C; Mehl, Steffen W

2015-01-01

Most surface water bodies (i.e., streams, lakes, etc.) are connected to the groundwater system to some degree so that changes to surface water bodies (either diversions or importations) can change flows in aquifer systems, and pumping from an aquifer can reduce discharge to, or induce additional recharge from streams, springs, and lakes. The timescales of these interactions are often very long (decades), making sustainable management of these systems difficult if relying only on observations of system responses. Instead, management scenarios are often analyzed based on numerical modeling. In this paper we propose a framework and metrics that can be used to relate the Theis concepts of capture to sustainable measures of stream-aquifer systems. We introduce four concepts: Sustainable Capture Fractions, Sustainable Capture Thresholds, Capture Efficiency, and Sustainable Groundwater Storage that can be used as the basis for developing metrics for sustainable management of stream-aquifer systems. We demonstrate their utility on a hypothetical stream-aquifer system where pumping captures both streamflow and discharge to phreatophytes at different amounts based on pumping location. In particular, Capture Efficiency (CE) can be easily understood by both scientists and non-scientist alike, and readily identifies vulnerabilities to sustainable stream-aquifer management when its value exceeds 100%. © 2014, National Ground Water Association.

Samba: a real-time motion capture system using wireless camera sensor networks.

PubMed

Oh, Hyeongseok; Cha, Geonho; Oh, Songhwai

2014-03-20

There is a growing interest in 3D content following the recent developments in 3D movies, 3D TVs and 3D smartphones. However, 3D content creation is still dominated by professionals, due to the high cost of 3D motion capture instruments. The availability of a low-cost motion capture system will promote 3D content generation by general users and accelerate the growth of the 3D market. In this paper, we describe the design and implementation of a real-time motion capture system based on a portable low-cost wireless camera sensor network. The proposed system performs motion capture based on the data-driven 3D human pose reconstruction method to reduce the computation time and to improve the 3D reconstruction accuracy. The system can reconstruct accurate 3D full-body poses at 16 frames per second using only eight markers on the subject's body. The performance of the motion capture system is evaluated extensively in experiments.

Samba: A Real-Time Motion Capture System Using Wireless Camera Sensor Networks

PubMed Central

Oh, Hyeongseok; Cha, Geonho; Oh, Songhwai

2014-01-01

There is a growing interest in 3D content following the recent developments in 3D movies, 3D TVs and 3D smartphones. However, 3D content creation is still dominated by professionals, due to the high cost of 3D motion capture instruments. The availability of a low-cost motion capture system will promote 3D content generation by general users and accelerate the growth of the 3D market. In this paper, we describe the design and implementation of a real-time motion capture system based on a portable low-cost wireless camera sensor network. The proposed system performs motion capture based on the data-driven 3D human pose reconstruction method to reduce the computation time and to improve the 3D reconstruction accuracy. The system can reconstruct accurate 3D full-body poses at 16 frames per second using only eight markers on the subject's body. The performance of the motion capture system is evaluated extensively in experiments. PMID:24658618

Targeting Human Serum Fucome by an Integrated Liquid-phase Multi Column Platform Operating in “Cascade” to Facilitate Comparative Mass Spectrometric Analysis of Disease-Free and Breast Cancer Sera

PubMed Central

Selvaraju, Subhashini; Rassi, Ziad El

2013-01-01

A fully integrated platform was developed for capturing/fractionating human fucome from disease-free and breast cancer sera. It comprised multicolumn operated by HPLC pumps and switching valves for the simultaneous depletion of high abundance proteins via affinity-based subtraction and the capturing of fucosylated glycoproteins via lectin affinity chromatography followed by the fractionation of the captured glycoproteins by reversed phase chromatography (RPC). Two lectin columns specific to fucose, namely Aleuria aurantia lectin (AAL) and Lotus tetragonolobus agglutinin (LTA) were utilized. The platform allowed the “cascading” of the serum sample from column-to-column in the liquid phase with no sample manipulation between the various steps. This guaranteed no sample loss and no propagation of experimental biases between the various columns. Finally, the fucome was fractionated by RPC yielding desalted fractions in volatile acetonitrile-rich mobile phase, which after vacuum evaporation were subjected to trypsinolysis for LC-MS/MS analysis. This permitted the identification of the differentially expressed proteins (DEP) in breast cancer serum yielding a broad panel of 35 DEP from the combined LTA and AAL captured proteins and a narrower panel of 8 DEP that were commonly differentially expressed in both LTA and AAL fractions, which are considered as more representative of cancer altered fucome. PMID:23533108

Remediation General Permit (RGP) for Massachusetts & New Hampshire

EPA Pesticide Factsheets

Documents, links & contacts for the Notice of Availability of the National Pollutant Discharge Elimination System (NPDES) General Permit for Remediation Activity Discharges – the Remediation General Permit in MA (MAG910000) and NH (NHG910000).

The National Solar Permitting Database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunderson, Renic

"The soft costs of solar — costs not associated with hardware — remain stubbornly high. Among the biggest soft costs are those associated with inefficiencies in local permitting and inspection. A study by the National Renewable Energy Laboratory and Lawrence Berkeley National Laboratory estimates that these costs add an average of $0.22/W per residential installation. This project helps reduce non-hardware/balance of system (BOS) costs by creating and maintaining a free and available site of permitting requirements and solar system verification software that installers can use to reduce time, capital, and resource investments in tracking permitting requirements. Software tools to identifymore » best permitting practices can enable government stakeholders to optimize their permitting process and remove superfluous costs and requirements. Like ""a Wikipedia for solar permitting"", users can add, edit, delete, and update information for a given jurisdiction. We incentivize this crowdsourcing approach by recognizing users for their contributions in the form of SEO benefits to their company or organization by linking back to users' websites."« less

Depletion and capture: revisiting “The source of water derived from wells"

USGS Publications Warehouse

Konikow, Leonard F.; Leake, Stanley A.

2014-01-01

A natural consequence of groundwater withdrawals is the removal of water from subsurface storage, but the overall rates and magnitude of groundwater depletion and capture relative to groundwater withdrawals (extraction or pumpage) have not previously been well characterized. This study assesses the partitioning of long-term cumulative withdrawal volumes into fractions derived from storage depletion and capture, where capture includes both increases in recharge and decreases in discharge. Numerical simulation of a hypothetical groundwater basin is used to further illustrate some of Theis' (1940) principles, particularly when capture is constrained by insufficient available water. Most prior studies of depletion and capture have assumed that capture is unconstrained through boundary conditions that yield linear responses. Examination of real systems indicates that capture and depletion fractions are highly variable in time and space. For a large sample of long-developed groundwater systems, the depletion fraction averages about 0.15 and the capture fraction averages about 0.85 based on cumulative volumes. Higher depletion fractions tend to occur in more arid regions, but the variation is high and the correlation coefficient between average annual precipitation and depletion fraction for individual systems is only 0.40. Because 85% of long-term pumpage is derived from capture in these real systems, capture must be recognized as a critical factor in assessing water budgets, groundwater storage depletion, and sustainability of groundwater development. Most capture translates into streamflow depletion, so it can detrimentally impact ecosystems.

Sewer System Management Plan.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, Robert C.

A Sewer System Management Plan (SSMP) is required by the State Water Resources Control Board (SWRCB) Order No. 2006-0003-DWQ Statewide General Waste Discharge Requirements (WDR) for Sanitary Sewer Systems (General Permit). DOE, National Nuclear Security Administration (NNSA), Sandia Field Office has filed a Notice of Intent to be covered under this General Permit. The General Permit requires a proactive approach to reduce the number and frequency of sanitary sewer overflows (SSOs) within the State. SSMPs must include provisions to provide proper and efficient management, operation, and maintenance of sanitary sewer systems and must contain a spill response plan.

40 CFR 63.4165 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... system; coating solvent flash-off and coating, curing, and drying occurs within the capture system and... when being moved between a spray booth and a curing oven. (b) If the capture system does not meet both... surface preparation activities and drying or curing time. (c) Liquid-to-uncaptured-gas protocol using a...

40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2013 CFR

2013-07-01

... system and add-on control device operating limits during the performance test? 63.3546 Section 63.3546... of key parameters of the valve operating system (e.g., solenoid valve operation, air pressure... minimum operating limit for that specific capture device or system of multiple capture devices. The...

40 CFR 63.4966 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.4966 Section 63... system and add-on control device operating limits during the performance test? During the performance... outlet gas temperature is the maximum operating limit for your condenser. (e) Emission capture system...

40 CFR 63.4966 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.4966 Section 63... system and add-on control device operating limits during the performance test? During the performance... outlet gas temperature is the maximum operating limit for your condenser. (e) Emission capture system...

Management of radioactive waste gases from PET radiopharmaceutical synthesis using cost effective capture systems integrated with a cyclotron safety system.

PubMed

Stimson, D H R; Pringle, A J; Maillet, D; King, A R; Nevin, S T; Venkatachalam, T K; Reutens, D C; Bhalla, R

2016-09-01

The emphasis on the reduction of gaseous radioactive effluent associated with PET radiochemistry laboratories has increased. Various radioactive gas capture strategies have been employed historically including expensive automated compression systems. We have implemented a new cost-effective strategy employing gas capture bags with electronic feedback that are integrated with the cyclotron safety system. Our strategy is suitable for multiple automated 18 F radiosynthesis modules and individual automated 11 C radiosynthesis modules. We describe novel gas capture systems that minimize the risk of human error and are routinely used in our facility.

Carbon dioxide capture from atmospheric air using sodium hydroxide spray.

PubMed

Stolaroff, Joshuah K; Keith, David W; Lowry, Gregory V

2008-04-15

In contrast to conventional carbon capture systems for power plants and other large point sources, the system described in this paper captures CO2 directly from ambient air. This has the advantages that emissions from diffuse sources and past emissions may be captured. The objective of this research is to determine the feasibility of a NaOH spray-based contactor for use in an air capture system by estimating the cost and energy requirements per unit CO2 captured. A prototype system is constructed and tested to measure CO2 absorption, energy use, and evaporative water loss and compared with theoretical predictions. A numerical model of drop collision and coalescence is used to estimate operating parameters for a full-scale system, and the cost of operating the system per unit CO2 captured is estimated. The analysis indicates that CO2 capture from air for climate change mitigation is technically feasible using off-the-shelf technology. Drop coalescence significantly decreases the CO2 absorption efficiency; however, fan and pump energy requirements are manageable. Water loss is significant (20 mol H2O/mol CO2 at 15 degrees C and 65% RH) but can be lowered by appropriately designing and operating the system. The cost of CO2 capture using NaOH spray (excluding solution recovery and CO2 sequestration, which may be comparable) in the full-scale system is 96 $/ton-CO2 in the base case, and ranges from 53 to 127 $/ton-CO2 under alternate operating parameters and assumptions regarding capital costs and mass transfer rate. The low end of the cost range is reached by a spray with 50 microm mean drop diameter, which is achievable with commercially available spray nozzles.

Boosted object hardware trigger development and testing for the Phase I upgrade of the ATLAS Experiment

NASA Astrophysics Data System (ADS)

Stark, Giordon; Atlas Collaboration

2015-04-01

The Global Feature Extraction (gFEX) module is a Level 1 jet trigger system planned for installation in ATLAS during the Phase 1 upgrade in 2018. The gFEX selects large-radius jets for capturing Lorentz-boosted objects by means of wide-area jet algorithms refined by subjet information. The architecture of the gFEX permits event-by-event local pile-up suppression for these jets using the same subtraction techniques developed for offline analyses. The gFEX architecture is also suitable for other global event algorithms such as missing transverse energy (MET), centrality for heavy ion collisions, and ``jets without jets.'' The gFEX will use 4 processor FPGAs to perform calculations on the incoming data and a Hybrid APU-FPGA for slow control of the module. The gFEX is unique in both design and implementation and substantially enhance the selectivity of the L1 trigger and increases sensitivity to key physics channels.

Untangling Brain-Wide Dynamics in Consciousness by Cross-Embedding

PubMed Central

Tajima, Satohiro; Yanagawa, Toru; Fujii, Naotaka; Toyoizumi, Taro

2015-01-01

Brain-wide interactions generating complex neural dynamics are considered crucial for emergent cognitive functions. However, the irreducible nature of nonlinear and high-dimensional dynamical interactions challenges conventional reductionist approaches. We introduce a model-free method, based on embedding theorems in nonlinear state-space reconstruction, that permits a simultaneous characterization of complexity in local dynamics, directed interactions between brain areas, and how the complexity is produced by the interactions. We demonstrate this method in large-scale electrophysiological recordings from awake and anesthetized monkeys. The cross-embedding method captures structured interaction underlying cortex-wide dynamics that may be missed by conventional correlation-based analysis, demonstrating a critical role of time-series analysis in characterizing brain state. The method reveals a consciousness-related hierarchy of cortical areas, where dynamical complexity increases along with cross-area information flow. These findings demonstrate the advantages of the cross-embedding method in deciphering large-scale and heterogeneous neuronal systems, suggesting a crucial contribution by sensory-frontoparietal interactions to the emergence of complex brain dynamics during consciousness. PMID:26584045

Optical ID Tags for Secure Verification of Multispectral Visible and NIR Signatures

NASA Astrophysics Data System (ADS)

Pérez-Cabré, Elisabet; Millán, María S.; Javidi, Bahram

2008-04-01

We propose to combine information from visible (VIS) and near infrared (NIR) spectral bands to increase robustness on security systems and deter from unauthorized use of optical tags that permit the identification of a given person or object. The signature that identifies the element under surveillance will be only obtained by the appropriate combination of the visible content and the NIR data. The fully-phase encryption technique is applied to avoid an easy recognition of the resultant signature at the naked eye and an easy reproduction using conventional devices for imaging or scanning. The obtained complex-amplitude encrypted distribution is encoded on an identity (ID) tag. Spatial multiplexing of the encrypted signature allows us to build a distortion-invariant ID tag, so that remote authentication can be achieved even if the tag is captured under rotation or at different distances. We explore the possibility of using partial information of the encrypted distribution. Simulation results are provided and discussed.

Testing Product Generation in Software Product Lines Using Pairwise for Features Coverage

NASA Astrophysics Data System (ADS)

Pérez Lamancha, Beatriz; Polo Usaola, Macario

A Software Product Lines (SPL) is "a set of software-intensive systems sharing a common, managed set of features that satisfy the specific needs of a particular market segment or mission and that are developed from a common set of core assets in a prescribed way". Variability is a central concept that permits the generation of different products of the family by reusing core assets. It is captured through features which, for a SPL, define its scope. Features are represented in a feature model, which is later used to generate the products from the line. From the testing point of view, testing all the possible combinations in feature models is not practical because: (1) the number of possible combinations (i.e., combinations of features for composing products) may be untreatable, and (2) some combinations may contain incompatible features. Thus, this paper resolves the problem by the implementation of combinatorial testing techniques adapted to the SPL context.

A Framework for Real-Time Collection, Analysis, and Classification of Ubiquitous Infrasound Data

NASA Astrophysics Data System (ADS)

Christe, A.; Garces, M. A.; Magana-Zook, S. A.; Schnurr, J. M.

2015-12-01

Traditional infrasound arrays are generally expensive to install and maintain. There are ~10^3 infrasound channels on Earth today. The amount of data currently provided by legacy architectures can be processed on a modest server. However, the growing availability of low-cost, ubiquitous, and dense infrasonic sensor networks presents a substantial increase in the volume, velocity, and variety of data flow. Initial data from a prototype ubiquitous global infrasound network is already pushing the boundaries of traditional research server and communication systems, in particular when serving data products over heterogeneous, international network topologies. We present a scalable, cloud-based approach for capturing and analyzing large amounts of dense infrasonic data (>10^6 channels). We utilize Akka actors with WebSockets to maintain data connections with infrasound sensors. Apache Spark provides streaming, batch, machine learning, and graph processing libraries which will permit signature classification, cross-correlation, and other analytics in near real time. This new framework and approach provide significant advantages in scalability and cost.

Broad-search algorithms for the spacecraft trajectory design of Callisto-Ganymede-Io triple flyby sequences from 2024 to 2040, Part II: Lambert pathfinding and trajectory solutions

NASA Astrophysics Data System (ADS)

Lynam, Alfred E.

2014-01-01

Triple-satellite-aided capture employs gravity-assist flybys of three of the Galilean moons of Jupiter in order to decrease the amount of ΔV required to capture a spacecraft into Jupiter orbit. Similarly, triple flybys can be used within a Jupiter satellite tour to rapidly modify the orbital parameters of a Jovicentric orbit, or to increase the number of science flybys. In order to provide a nearly comprehensive search of the solution space of Callisto-Ganymede-Io triple flybys from 2024 to 2040, a third-order, Chebyshev's method variant of the p-iteration solution to Lambert's problem is paired with a second-order, Newton-Raphson method, time of flight iteration solution to the V∞-matching problem. The iterative solutions of these problems provide the orbital parameters of the Callisto-Ganymede transfer, the Ganymede flyby, and the Ganymede-Io transfer, but the characteristics of the Callisto and Io flybys are unconstrained, so they are permitted to vary in order to produce an even larger number of trajectory solutions. The vast amount of solution data is searched to find the best triple-satellite-aided capture window between 2024 and 2040.

System and process for capture of acid gasses at elevated pressure from gaseous process streams

DOEpatents

Heldebrant, David J.; Koech, Phillip K.; Linehan, John C.; Rainbolt, James E.; Bearden, Mark D.; Zheng, Feng

2016-09-06

A system, method, and material that enables the pressure-activated reversible chemical capture of acid gasses such as CO.sub.2 from gas volumes such as streams, flows or any other volume. Once the acid gas is chemically captured, the resulting product typically a zwitterionic salt, can be subjected to a reduced pressure whereupon the resulting product will release the captures acid gas and the capture material will be regenerated. The invention includes this process as well as the materials and systems for carrying out and enabling this process.

Stability of a slotted ALOHA system with capture effect

NASA Astrophysics Data System (ADS)

Onozato, Yoshikuni; Liu, Jin; Noguchi, Shoichi

1989-02-01

The stability of a slotted ALOHA system with capture effect is investigated under a general communication environment where terminals are divided into two groups (low-power and high-power) and the capture effect is modeled by capture probabilities. An approximate analysis is developed using catastrophe theory, in which the effects of system and user parameters on the stability are characterized by the cusp catastrophe. Particular attention is given to the low-power group, since it must bear the strain under the capture effect. The stability conditions of the two groups are given explicitly by bifurcation sets.

NPDES Permit for Riverview Estates Wastewater Treatment Facility in North Dakota

EPA Pesticide Factsheets

Under National Pollutant Discharge Elimination System permit number ND-0031143, the Riverview Estates Wastewater Treatment Facility is authorized to discharge from its wastewater treatment facility in designated locations as described in the permit.

30 CFR 784.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.1 Scope. This part... mining operations and reclamation plans portions of applications for permits for underground mining...

50 CFR 622.373 - Limited access system for charter vessel/headboat permits for Gulf coastal migratory pelagic fish.

Code of Federal Regulations, 2013 CFR

2013-10-01

.../headboat permits for Gulf coastal migratory pelagic fish. 622.373 Section 622.373 Wildlife and Fisheries... for Gulf coastal migratory pelagic fish. (a) No applications for additional charter vessel/headboat permits for Gulf coastal migratory pelagic fish will be accepted. Existing permits may be renewed, are...

50 CFR 622.373 - Limited access system for charter vessel/headboat permits for Gulf coastal migratory pelagic fish.

Code of Federal Regulations, 2014 CFR

2014-10-01

.../headboat permits for Gulf coastal migratory pelagic fish. 622.373 Section 622.373 Wildlife and Fisheries... for Gulf coastal migratory pelagic fish. (a) No applications for additional charter vessel/headboat permits for Gulf coastal migratory pelagic fish will be accepted. Existing permits may be renewed, are...

36 CFR 13.1150 - Is a permit required for a vessel in Glacier Bay?

Code of Federal Regulations, 2010 CFR

2010-07-01

... vessel in Glacier Bay? 13.1150 Section 13.1150 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Glacier Bay National Park and Preserve Vessel Permits § 13.1150 Is a permit required for a vessel in Glacier Bay? A permit from...

36 CFR 13.1150 - Is a permit required for a vessel in Glacier Bay?

Code of Federal Regulations, 2011 CFR

2011-07-01

... vessel in Glacier Bay? 13.1150 Section 13.1150 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Glacier Bay National Park and Preserve Vessel Permits § 13.1150 Is a permit required for a vessel in Glacier Bay? A permit from...

36 CFR 13.1150 - Is a permit required for a vessel in Glacier Bay?

Code of Federal Regulations, 2012 CFR

2012-07-01

... vessel in Glacier Bay? 13.1150 Section 13.1150 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Glacier Bay National Park and Preserve Vessel Permits § 13.1150 Is a permit required for a vessel in Glacier Bay? A permit from...

36 CFR 13.1150 - Is a permit required for a vessel in Glacier Bay?

Code of Federal Regulations, 2014 CFR

2014-07-01

... vessel in Glacier Bay? 13.1150 Section 13.1150 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Glacier Bay National Park and Preserve Vessel Permits § 13.1150 Is a permit required for a vessel in Glacier Bay? A permit from...

How we developed eForms: an electronic form and data capture tool to support assessment in mobile medical education.

PubMed

Mooney, Jane S; Cappelli, Tim; Byrne-Davis, Lucie; Lumsden, Colin J

2014-12-01

Mobile learning technologies are being introduced and adopted by an increasing number of medical schools. Following the implementation of these devices, institutions are tasked with the challenge of their integration into curriculum delivery and presented with the opportunity to facilitate data collection from large student cohorts. Since 2011, Manchester Medical School (MMS) has undertaken the largest deployment of iPads within UK Higher Education. Working towards the more efficient collation of students' compulsory workplace-based assessment data led us to evaluate how existing information management software could replace previously paper-based systems. Following an evaluation of six, and a trial of one, commercially available packages, the existing software solutions were found to be inflexible and unfit for purpose. This resulted in the development of a new digital solution that addressed the limitations of the previous system. "University of Manchester (UoM) eForms" consists of an app and a web-based administration system that respectively permit high volume data collection and management. UoM eForms has now replaced the preceding paper-based and electronic systems within MMS for workplace-based assessment administration, due to the improved usability and dynamicity built into its interface and infrastructure. This new system has found many further useful applications, including research data collection, feedback, placement evaluations, quality assurance and interview marking.

Reducing concentrated animal feeding operations permitting requirements.

PubMed

Centner, T J; Newton, G L

2011-12-01

Many owners and operators of concentrated animal feeding operations (CAFO) need to secure National Pollutant Discharge Elimination System permits from the federal or state permitting authority. Because of the expense and inconvenience of permit applications, farm groups have challenged revisions to the federal CAFO Rule as well as state regulations claiming selected provisions exceeded the authority of the permitting agency. In 2011, 2 courts responded with decisions that clarify federal and state permitting regulations. Another goal of agricultural groups is to change the regulatory authority of the state from an environmental agency to a department of agriculture. These developments suggest that by altering the permitting authority, CAFO owners and operators may alleviate some of the burdens of the permitting process.

Study on launch scheme of space-net capturing system.

PubMed

Gao, Qingyu; Zhang, Qingbin; Feng, Zhiwei; Tang, Qiangang

2017-01-01

With the continuous progress in active debris-removal technology, scientists are increasingly concerned about the concept of space-net capturing system. The space-net capturing system is a long-range-launch flexible capture system, which has great potential to capture non-cooperative targets such as inactive satellites and upper stages. In this work, the launch scheme is studied by experiment and simulation, including two-step ejection and multi-point-traction analyses. The numerical model of the tether/net is based on finite element method and is verified by full-scale ground experiment. The results of the ground experiment and numerical simulation show that the two-step ejection and six-point traction scheme of the space-net system is superior to the traditional one-step ejection and four-point traction launch scheme.

Study on launch scheme of space-net capturing system

PubMed Central

Zhang, Qingbin; Feng, Zhiwei; Tang, Qiangang

2017-01-01

With the continuous progress in active debris-removal technology, scientists are increasingly concerned about the concept of space-net capturing system. The space-net capturing system is a long-range-launch flexible capture system, which has great potential to capture non-cooperative targets such as inactive satellites and upper stages. In this work, the launch scheme is studied by experiment and simulation, including two-step ejection and multi-point-traction analyses. The numerical model of the tether/net is based on finite element method and is verified by full-scale ground experiment. The results of the ground experiment and numerical simulation show that the two-step ejection and six-point traction scheme of the space-net system is superior to the traditional one-step ejection and four-point traction launch scheme. PMID:28877187

40 CFR 270.16 - Specific part B information requirements for tank systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) SOLID WASTES (CONTINUED) EPA ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM... systems in which ignitable, reactive, or incompatible wastes are to be stored or treated, a description of...

NEUTRON ABSORPTION AND SHIELDING DEVICE

DOEpatents

Axelrad, I.R.

1960-06-21

A neutron absorption and shielding device is described which is adapted for mounting in a radiation shielding wall surrounding a radioactive area through which instrumentation leads and the like may safely pass without permitting gamma or neutron radiation to pass to the exterior. The shielding device comprises a container having at least one nonrectilinear tube or passageway means extending therethrough, which is adapted to contain instrumentation leads or the like, a layer of a substance capable of absorbing gamma rays, and a solid resinous composition adapted to attenuate fast-moving neutrons and capture slow- moving or thermal neutrons.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flanigan, Tom; Pybus, Craig; Roy, Sonya

This report summarizes the results of the Pre-Front End Engineering Design (pre-FEED) phase of a proposed advanced oxy-combustion power generation plant to repower the existing 200 MWe Unit 4 at Ameren Energy Resources’ (AER) Meredosia Power Plant. AER has formed an alliance with Air Liquide Process and Construction, Inc. (ALPC) and Babcock & Wilcox Power Generation Group (B&W PGG) for the design, construction, and testing of the facility, and has contracted with URS Corporation (URS) for preliminary design and Owner’s engineering services. The Project employs oxy-combustion technology – combustion of coal with nearly pure oxygen and recycled flue gas (insteadmore » of air) – to capture approximately 90% of the flue gas CO2 for transport and sequestration by another Project. Plant capacity and configuration has been developed based on the B&W PGG-ALPC cool recycle process firing high-sulfur bituminous coal fuel, assuming baseload plant operation to maximize existing steam turbine capability, with limited consideration for plant redundancy and performance optimization in order to keep plant costs as low as practical. Activities and preliminary results from the pre-FEED phase addressed in this report include the following: Overall plant thermal performance; Equipment sizing and system configuration; Plant operation and control philosophy; Plant emissions and effluents; CO 2 production and recovery characteristics; Project cost estimate and economic evaluation; Integrated project engineering and construction schedule; Project risk and opportunity assessment; Development of Project permitting strategy and requirements During the Phase 2 of the Project, additional design details will be developed and the Phase 1 work products updated to support actual construction and operation of the facility in Phase 3. Additional information will be provided early in Phase 2 to support Ameren-Environmental in finalizing the appropriate permitting strategies and permit applications. Additional performance and reliability enhancements will also be evaluated in Phase 2 to try to improve overall project economics.« less

A Probabilistic Framework for the Validation and Certification of Computer Simulations

NASA Technical Reports Server (NTRS)

Ghanem, Roger; Knio, Omar

2000-01-01

The paper presents a methodology for quantifying, propagating, and managing the uncertainty in the data required to initialize computer simulations of complex phenomena. The purpose of the methodology is to permit the quantitative assessment of a certification level to be associated with the predictions from the simulations, as well as the design of a data acquisition strategy to achieve a target level of certification. The value of a methodology that can address the above issues is obvious, specially in light of the trend in the availability of computational resources, as well as the trend in sensor technology. These two trends make it possible to probe physical phenomena both with physical sensors, as well as with complex models, at previously inconceivable levels. With these new abilities arises the need to develop the knowledge to integrate the information from sensors and computer simulations. This is achieved in the present work by tracing both activities back to a level of abstraction that highlights their commonalities, thus allowing them to be manipulated in a mathematically consistent fashion. In particular, the mathematical theory underlying computer simulations has long been associated with partial differential equations and functional analysis concepts such as Hilbert spares and orthogonal projections. By relying on a probabilistic framework for the modeling of data, a Hilbert space framework emerges that permits the modeling of coefficients in the governing equations as random variables, or equivalently, as elements in a Hilbert space. This permits the development of an approximation theory for probabilistic problems that parallels that of deterministic approximation theory. According to this formalism, the solution of the problem is identified by its projection on a basis in the Hilbert space of random variables, as opposed to more traditional techniques where the solution is approximated by its first or second-order statistics. The present representation, in addition to capturing significantly more information than the traditional approach, facilitates the linkage between different interacting stochastic systems as is typically observed in real-life situations.

77 FR 19011 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-29

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On February 6, 2012, Spartanburg Water System... Schneider, General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251, Spartanburg, South...

Depletion and capture: revisiting "the source of water derived from wells".

PubMed

Konikow, L F; Leake, S A

2014-09-01

A natural consequence of groundwater withdrawals is the removal of water from subsurface storage, but the overall rates and magnitude of groundwater depletion and capture relative to groundwater withdrawals (extraction or pumpage) have not previously been well characterized. This study assesses the partitioning of long-term cumulative withdrawal volumes into fractions derived from storage depletion and capture, where capture includes both increases in recharge and decreases in discharge. Numerical simulation of a hypothetical groundwater basin is used to further illustrate some of Theis' (1940) principles, particularly when capture is constrained by insufficient available water. Most prior studies of depletion and capture have assumed that capture is unconstrained through boundary conditions that yield linear responses. Examination of real systems indicates that capture and depletion fractions are highly variable in time and space. For a large sample of long-developed groundwater systems, the depletion fraction averages about 0.15 and the capture fraction averages about 0.85 based on cumulative volumes. Higher depletion fractions tend to occur in more arid regions, but the variation is high and the correlation coefficient between average annual precipitation and depletion fraction for individual systems is only 0.40. Because 85% of long-term pumpage is derived from capture in these real systems, capture must be recognized as a critical factor in assessing water budgets, groundwater storage depletion, and sustainability of groundwater development. Most capture translates into streamflow depletion, so it can detrimentally impact ecosystems. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Validation of enhanced kinect sensor based motion capturing for gait assessment

PubMed Central

Müller, Björn; Ilg, Winfried; Giese, Martin A.

2017-01-01

Optical motion capturing systems are expensive and require substantial dedicated space to be set up. On the other hand, they provide unsurpassed accuracy and reliability. In many situations however flexibility is required and the motion capturing system can only temporarily be placed. The Microsoft Kinect v2 sensor is comparatively cheap and with respect to gait analysis promising results have been published. We here present a motion capturing system that is easy to set up, flexible with respect to the sensor locations and delivers high accuracy in gait parameters comparable to a gold standard motion capturing system (VICON). Further, we demonstrate that sensor setups which track the person only from one-side are less accurate and should be replaced by two-sided setups. With respect to commonly analyzed gait parameters, especially step width, our system shows higher agreement with the VICON system than previous reports. PMID:28410413

Transforming Functional Requirements from UML into BPEL to Efficiently Develop SOA-Based Systems

NASA Astrophysics Data System (ADS)

Vemulapalli, Anisha; Subramanian, Nary

The intended behavior of any system such as services, tasks or functions can be captured by functional requirements of the system. As our dependence on online services has grown steadily, the web applications are being developed employing the SOA. BPEL4WS provides a means for expressing functional requirements of an SOA-based system by providing constructs to capture business goals and objectives for the system. In this paper we propose an approach for transforming user-centered requirements captured using UML into a corresponding BPEL specification, where the business processes are captured by means of use-cases from which UML sequence diagrams and activity diagrams are extracted. Subsequently these UML models are mapped to BPEL specifications that capture the essence of the initial business requirements to develop the SOA-based system by employing CASE tools. A student housing system is used as a case study to illustrate this approach and the system is validated using NetBeans.

Capturing asteroids into bound orbits around the earth: Massive early return on an asteroid terminal defense system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hills, J.G.

1992-02-06

Nuclear explosives may be used to capture small asteroids (e.g., 20--50 meters in diameter) into bound orbits around the earth. The captured objects could be used for construction material for manned and unmanned activity in Earth orbit. Asteroids with small approach velocities, which are the ones most likely to have close approaches to the Earth, require the least energy for capture. They are particularly easy to capture if they pass within one Earth radius of the surface of the Earth. They could be intercepted with intercontinental missiles if the latter were retrofit with a more flexible guiding and homing capability.more » This asteroid capture-defense system could be implemented in a few years at low cost by using decommissioned ICMs. The economic value of even one captured asteroid is many times the initial investment. The asteroid capture system would be an essential part of the learning curve for dealing with larger asteroids that can hit the earth.« less

40 CFR 63.4291 - What are my options for meeting the emission limits?

Code of Federal Regulations, 2010 CFR

2010-07-01

... emission capture systems and add-on controls, the organic HAP emission rate for the web coating/printing... demonstrate that all capture systems and control devices for the web coating/printing operation(s) meet the... capture systems and control devices for the web coating/printing operation(s) meet the operating limits...

40 CFR 63.4181 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... commercial or industrial HVAC systems. Manufacturer's formulation data means data on a material (such as a... capture system efficiency means the portion (expressed as a percentage) of the pollutants from an emission source that is delivered to an add-on control device. Capture system means one or more capture devices...

40 CFR 63.4181 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... commercial or industrial HVAC systems. Manufacturer's formulation data means data on a material (such as a.... Capture efficiency or capture system efficiency means the portion (expressed as a percentage) of the pollutants from an emission source that is delivered to an add-on control device. Capture system means one or...

40 CFR 63.4181 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... commercial or industrial HVAC systems. Manufacturer's formulation data means data on a material (such as a.... Capture efficiency or capture system efficiency means the portion (expressed as a percentage) of the pollutants from an emission source that is delivered to an add-on control device. Capture system means one or...

40 CFR 63.4181 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... commercial or industrial HVAC systems. Manufacturer's formulation data means data on a material (such as a... capture system efficiency means the portion (expressed as a percentage) of the pollutants from an emission source that is delivered to an add-on control device. Capture system means one or more capture devices...

40 CFR 63.4181 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... commercial or industrial HVAC systems. Manufacturer's formulation data means data on a material (such as a.... Capture efficiency or capture system efficiency means the portion (expressed as a percentage) of the pollutants from an emission source that is delivered to an add-on control device. Capture system means one or...

Invasive meningococcal disease in the Veneto region of Italy: a capture-recapture analysis for assessing the effectiveness of an integrated surveillance system.

PubMed

Baldovin, Tatjana; Lazzari, Roberta; Cocchio, Silvia; Furlan, Patrizia; Bertoncello, Chiara; Saia, Mario; Russo, Francesca; Baldo, Vincenzo

2017-05-02

Epidemiology of Neisseria meningitidis has been changing since the introduction of universal vaccination programmes against meningococcal serogroup C (MenC) and meningococcal serogroup B (MenB) has now become dominant. This study aimed to analyse the cases reported in institutional data recording systems to estimate the burden of invasive meningococcal diseases (IMDs) and assess the effectiveness of surveillance in Veneto region (Italy). Analysis was performed from 2007 to 2014 on data recorded in different systems: Mandatory Notification System, National Surveillance of Invasive Bacterial Diseases System and Laboratories Surveillance System (LSS), which were pooled into a combined surveillance system (CSS) and hospital discharge records (HDRs). A capture-recapture method was used and completeness of each source estimated. Number of cases with IMD by source of information and year, incidence of IMD by age group, case fatality rate (CFR) and distribution of meningococcal serogroups by year were also analysed. Combining the four data systems enabled the identification of 179 confirmed cases with IMD, achieving an overall sensitivity of 94.7% (95% CI: 90.8% to 98.8%), while it was 76.7% (95% CI: 73.6% to 80.1%) for CSS and 77.2% (95% CI: 74.1% to 80.6%) for HDRs. Typing of isolates was done in 80% of cases, and 95.2% of the typed cases were provided by LSS. Serogroup B was confirmed in 50.3% of cases. The estimated IMD notification rate (cases with IMD diagnosed and reported to the surveillance systems) was 0.48/100 000 population, and incidence peaked at 6.2/100 000 in children aged <1 year old (60.9% due to MenB), and increased slightly in the age group between 15 and 19 years (1.1/100 000). A CFR of 14% was recorded (8.7% in paediatric age). Quality of surveillance systems relies on case ascertainment based on serological characterisation of the circulating strains by microbiology laboratories. All available sources should be routinely combined to improve the epidemiology of IMD and the information used by public health departments to conduct timely preventive measures. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

41 CFR 102-74.485 - Is there any limitation on the length of time of a permit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... on the length of time of a permit? 102-74.485 Section 102-74.485 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL... limitation on the length of time of a permit? Yes, a permit may not be issued for a period of time in excess...

41 CFR 102-74.485 - Is there any limitation on the length of time of a permit?

Code of Federal Regulations, 2011 CFR

2011-01-01

... on the length of time of a permit? 102-74.485 Section 102-74.485 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL... limitation on the length of time of a permit? Yes, a permit may not be issued for a period of time in excess...

77 FR 16220 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On December 20, 2011, Spartanburg Water System... Contact: Ms. Sue Schneider, General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251...

76 FR 67179 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-31

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On June 23, 2011, Spartanburg Water System (Spartanburg..., General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251, Spartanburg, South Carolina 29304...

30 CFR 784.10 - Information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.10... requires applicants for permits for underground coal mines to prepare and submit an operation and...

30 CFR 780.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 780.1 Scope. This part provides the... operations and reclamation plan portions of applications for permits for surface mining activities, except to...

Public Notice: (Draft Permit) Pesticide General Permit for the State of Rhode Island, RIG870000

EPA Pesticide Factsheets

A public notice of a draft Rhode Island Pollutant Discharge Elimination System (RIPDES) General Permit (GP) for Discharges from the Application of Pesticides. The public comment period is April 6, 2017 - May 12, 2017.

32 CFR 322.7 - Exempt systems of records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... information permits more informed decision-making by the Department when making required suitability... becomes clear. Such information permits more informed decision-making by the Department when making... becomes clear. Such information permits more informed decision-making by the Department when making...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... being used contains the appropriate pollution control technologies (or equivalent systems/pesticide... appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit writer which... written submission to the appropriate permitting authority, e.g., the local Control Authority (the POTW...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... being used contains the appropriate pollution control technologies (or equivalent systems/pesticide... appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit writer which... written submission to the appropriate permitting authority, e.g., the local Control Authority (the POTW...

A Simplified Model of ARIS for Optimal Controller Design

NASA Technical Reports Server (NTRS)

Beech, Geoffrey S.; Hampton, R. David; Kross, Denny (Technical Monitor)

2001-01-01

Many space-science experiments require active vibration isolation. Boeing's Active Rack Isolation System (ARIS) isolates experiments at the rack (vs. experiment or sub-experiment) level, with multi e experiments per rack. An ARIS-isolated rack typically employs eight actuators and thirteen umbilicals; the umbilicals provide services such as power, data transmission, and cooling. Hampton, et al., used "Kane's method" to develop an analytical, nonlinear, rigid-body model of ARIS that includes full actuator dynamics (inertias). This model, less the umbilicals, was first implemented for simulation by Beech and Hampton; they developed and tested their model using two commercial-off-the-shelf (COTS) software packages. Rupert, et al., added umbilical-transmitted disturbances to this nonlinear model. Because the nonlinear model, even for the untethered system, is both exceedingly complex and "encapsulated" inside these COTS tools, it is largely inaccessible to ARIS controller designers. This paper shows that ISPR rattle-space constraints and small ARIS actuator masses permit considerable model simplification, without significant loss of fidelity. First, for various loading conditions, comparisons are made between the dynamic responses of the nonlinear model (untethered) and a truth model. Then comparisons are made among nonlinear, linearized, and linearized reduced-mass models. It is concluded that these three models all capture the significant system rigid-body dynamics, with the third being preferred due to its relative simplicity.

An experimental platform for triaxial high-pressure/high-temperature testing of rocks using computed tomography

NASA Astrophysics Data System (ADS)

Glatz, Guenther; Lapene, Alexandre; Castanier, Louis M.; Kovscek, Anthony R.

2018-04-01

A conventional high-pressure/high-temperature experimental apparatus for combined geomechanical and flow-through testing of rocks is not X-ray compatible. Additionally, current X-ray transparent systems for computed tomography (CT) of cm-sized samples are limited to design temperatures below 180 °C. We describe a novel, high-temperature (>400 °C), high-pressure (>2000 psi/>13.8 MPa confining, >10 000 psi/>68.9 MPa vertical load) triaxial core holder suitable for X-ray CT scanning. The new triaxial system permits time-lapse imaging to capture the role of effective stress on fluid distribution and porous medium mechanics. System capabilities are demonstrated using ultimate compressive strength (UCS) tests of Castlegate sandstone. In this case, flooding the porous medium with a radio-opaque gas such as krypton before and after the UCS test improves the discrimination of rock features such as fractures. The results of high-temperature tests are also presented. A Uintah Basin sample of immature oil shale is heated from room temperature to 459 °C under uniaxial compression. The sample contains kerogen that pyrolyzes as temperature rises, releasing hydrocarbons. Imaging reveals the formation of stress bands as well as the evolution and connectivity of the fracture network within the sample as a function of time.

An experimental platform for triaxial high-pressure/high-temperature testing of rocks using computed tomography.

PubMed

Glatz, Guenther; Lapene, Alexandre; Castanier, Louis M; Kovscek, Anthony R

2018-04-01

A conventional high-pressure/high-temperature experimental apparatus for combined geomechanical and flow-through testing of rocks is not X-ray compatible. Additionally, current X-ray transparent systems for computed tomography (CT) of cm-sized samples are limited to design temperatures below 180 °C. We describe a novel, high-temperature (>400 °C), high-pressure (>2000 psi/>13.8 MPa confining, >10 000 psi/>68.9 MPa vertical load) triaxial core holder suitable for X-ray CT scanning. The new triaxial system permits time-lapse imaging to capture the role of effective stress on fluid distribution and porous medium mechanics. System capabilities are demonstrated using ultimate compressive strength (UCS) tests of Castlegate sandstone. In this case, flooding the porous medium with a radio-opaque gas such as krypton before and after the UCS test improves the discrimination of rock features such as fractures. The results of high-temperature tests are also presented. A Uintah Basin sample of immature oil shale is heated from room temperature to 459 °C under uniaxial compression. The sample contains kerogen that pyrolyzes as temperature rises, releasing hydrocarbons. Imaging reveals the formation of stress bands as well as the evolution and connectivity of the fracture network within the sample as a function of time.

34 CFR 99.38 - What conditions apply to disclosure of information as permitted by State statute adopted after...

Code of Federal Regulations, 2013 CFR

2013-07-01

... permitted by State statute adopted after November 19, 1974, concerning the juvenile justice system? 99.38... adopted after November 19, 1974, concerning the juvenile justice system? (a) If reporting or disclosure allowed by State statute concerns the juvenile justice system and the system's ability to effectively...

34 CFR 99.38 - What conditions apply to disclosure of information as permitted by State statute adopted after...

Code of Federal Regulations, 2012 CFR

2012-07-01

... permitted by State statute adopted after November 19, 1974, concerning the juvenile justice system? 99.38... adopted after November 19, 1974, concerning the juvenile justice system? (a) If reporting or disclosure allowed by State statute concerns the juvenile justice system and the system's ability to effectively...

34 CFR 99.38 - What conditions apply to disclosure of information as permitted by State statute adopted after...

Code of Federal Regulations, 2011 CFR

2011-07-01

... permitted by State statute adopted after November 19, 1974, concerning the juvenile justice system? 99.38... adopted after November 19, 1974, concerning the juvenile justice system? (a) If reporting or disclosure allowed by State statute concerns the juvenile justice system and the system's ability to effectively...

34 CFR 99.38 - What conditions apply to disclosure of information as permitted by State statute adopted after...

Code of Federal Regulations, 2014 CFR

2014-07-01

... permitted by State statute adopted after November 19, 1974, concerning the juvenile justice system? 99.38... adopted after November 19, 1974, concerning the juvenile justice system? (a) If reporting or disclosure allowed by State statute concerns the juvenile justice system and the system's ability to effectively...

Value in cardiovascular care.

PubMed

Bradley, Steven M; Strauss, Craig E; Ho, P Michael

2017-08-01

Healthcare value, defined as health outcomes achieved relative to the costs of care, has been proposed as a unifying approach to measure improvements in the quality and affordability of healthcare. Although value is of increasing interest to payers, many providers remain unfamiliar with how value differs from other approaches to the comparison of cost and outcomes (ie, cost-effectiveness analysis). While cost-effectiveness studies can be used by policy makers and payers to inform decisions about coverage and reimbursement for new therapies, the assessment of healthcare can guide improvements in the delivery of healthcare to achieve better outcomes at lower cost. Comparison on value allows for the identification of healthcare delivery organisations or care delivery settings where patient outcomes have been optimised at a lower cost. Gaps remain in the measurement of healthcare value, particularly as it relates to patient-reported health status (symptoms, functional status and health-related quality of life). The use of technology platforms that capture health status measures with minimal disruption to clinical workflow (ie, web portals, automated telephonic systems and tablets to facilitate capture outside of in-person clinical interaction) is facilitating use of health status measures to improve clinical care and optimise patient outcomes. Furthermore, the use of a value framework has catalysed quality improvement efforts and research to seek better patient outcomes at lower cost. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Near Infrared Imaging As a Method of Studying Tsetse Fly (Diptera: Glossinidae) Pupal Development

PubMed Central

Moran, Zelda R.; Parker, Andrew G.

2016-01-01

Abstract Near infrared (NIR) photography and video was investigated as a method for observing and recording intrapuparial development in the tsetse fly Glossina palpalis gambiensis and other Muscomorpha (Cyclorrhapha) Diptera. We showed that NIR light passes through the puparium, permitting images of the true pupae and pharate adult to be captured. Various wavelengths of NIR light from 880 to 1060 nm were compared to study the development of tsetse fly pupae from larviposition to emergence, using time-lapse videos and photographs. This study was carried out to advance our understanding of tsetse pupal development, specifically with the goal of improving a sorting technique which could separate male from female tsetse flies several days before emergence. Separation of the sexes at this stage is highly desirable for operational tsetse sterile insect technique control programmes, as it would permit the easy retention of females for the colony while allowing the males to be handled, irradiated and shipped in the pupal stage when they are less sensitive to vibration. In addition, it presents a new methodology for studying the pupal stage of many coarctate insects for many applications. NIR imaging permits observation of living pupae, allowing the entire development process to be observed without disruption. PMID:27402791

Managing complex processing of medical image sequences by program supervision techniques

NASA Astrophysics Data System (ADS)

Crubezy, Monica; Aubry, Florent; Moisan, Sabine; Chameroy, Virginie; Thonnat, Monique; Di Paola, Robert

1997-05-01

Our objective is to offer clinicians wider access to evolving medical image processing (MIP) techniques, crucial to improve assessment and quantification of physiological processes, but difficult to handle for non-specialists in MIP. Based on artificial intelligence techniques, our approach consists in the development of a knowledge-based program supervision system, automating the management of MIP libraries. It comprises a library of programs, a knowledge base capturing the expertise about programs and data and a supervision engine. It selects, organizes and executes the appropriate MIP programs given a goal to achieve and a data set, with dynamic feedback based on the results obtained. It also advises users in the development of new procedures chaining MIP programs.. We have experimented the approach for an application of factor analysis of medical image sequences as a means of predicting the response of osteosarcoma to chemotherapy, with both MRI and NM dynamic image sequences. As a result our program supervision system frees clinical end-users from performing tasks outside their competence, permitting them to concentrate on clinical issues. Therefore our approach enables a better exploitation of possibilities offered by MIP and higher quality results, both in terms of robustness and reliability.

Flight test of the X-29A at high angle of attack: Flight dynamics and controls

NASA Technical Reports Server (NTRS)

Bauer, Jeffrey E.; Clarke, Robert; Burken, John J.

1995-01-01

The NASA Dryden Flight Research Center has flight tested two X-29A aircraft at low and high angles of attack. The high-angle-of-attack tests evaluate the feasibility of integrated X-29A technologies. More specific objectives focus on evaluating the high-angle-of-attack flying qualities, defining multiaxis controllability limits, and determining the maximum pitch-pointing capability. A pilot-selectable gain system allows examination of tradeoffs in airplane stability and maneuverability. Basic fighter maneuvers provide qualitative evaluation. Bank angle captures permit qualitative data analysis. This paper discusses the design goals and approach for high-angle-of-attack control laws and provides results from the envelope expansion and handling qualities testing at intermediate angles of attack. Comparisons of the flight test results to the predictions are made where appropriate. The pitch rate command structure of the longitudinal control system is shown to be a valid design for high-angle-of-attack control laws. Flight test results show that wing rock amplitude was overpredicted and aileron and rudder effectiveness were underpredicted. Flight tests show the X-29A airplane to be a good aircraft up to 40 deg angle of attack.

Hadamard multimode optical imaging transceiver

DOEpatents

Cooke, Bradly J; Guenther, David C; Tiee, Joe J; Kellum, Mervyn J; Olivas, Nicholas L; Weisse-Bernstein, Nina R; Judd, Stephen L; Braun, Thomas R

2012-10-30

Disclosed is a method and system for simultaneously acquiring and producing results for multiple image modes using a common sensor without optical filtering, scanning, or other moving parts. The system and method utilize the Walsh-Hadamard correlation detection process (e.g., functions/matrix) to provide an all-binary structure that permits seamless bridging between analog and digital domains. An embodiment may capture an incoming optical signal at an optical aperture, convert the optical signal to an electrical signal, pass the electrical signal through a Low-Noise Amplifier (LNA) to create an LNA signal, pass the LNA signal through one or more correlators where each correlator has a corresponding Walsh-Hadamard (WH) binary basis function, calculate a correlation output coefficient for each correlator as a function of the corresponding WH binary basis function in accordance with Walsh-Hadamard mathematical principles, digitize each of the correlation output coefficient by passing each correlation output coefficient through an Analog-to-Digital Converter (ADC), and performing image mode processing on the digitized correlation output coefficients as desired to produce one or more image modes. Some, but not all, potential image modes include: multi-channel access, temporal, range, three-dimensional, and synthetic aperture.

40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2010 CFR

2010-07-01

... system and add-on control device operating limits during the performance test? 63.3546 Section 63.3546... device or system of multiple capture devices. The average duct static pressure is the maximum operating... Add-on Controls Option § 63.3546 How do I establish the emission capture system and add-on control...

40 CFR 63.4966 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2013 CFR

2013-07-01

... system and add-on control device operating limits during the performance test? 63.4966 Section 63.4966... outlet gas temperature is the maximum operating limit for your condenser. (e) Emission capture system... Emission Rate with Add-on Controls Option § 63.4966 How do I establish the emission capture system and add...

40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2011 CFR

2011-07-01

... system and add-on control device operating limits during the performance test? 63.3546 Section 63.3546... device or system of multiple capture devices. The average duct static pressure is the maximum operating... Add-on Controls Option § 63.3546 How do I establish the emission capture system and add-on control...

40 CFR 63.4966 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2011 CFR

2011-07-01

... system and add-on control device operating limits during the performance test? 63.4966 Section 63.4966... outlet gas temperature is the maximum operating limit for your condenser. (e) Emission capture system... with Add-on Controls Option § 63.4966 How do I establish the emission capture system and add-on control...

40 CFR 63.4966 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2010 CFR

2010-07-01

... system and add-on control device operating limits during the performance test? 63.4966 Section 63.4966... outlet gas temperature is the maximum operating limit for your condenser. (e) Emission capture system... with Add-on Controls Option § 63.4966 How do I establish the emission capture system and add-on control...

41 CFR 301-71.2 - What are the standard data elements and when must they be captured on a travel accounting system?

Code of Federal Regulations, 2010 CFR

2010-07-01

... data elements and when must they be captured on a travel accounting system? 301-71.2 Section 301-71.2 Public Contracts and Property Management Federal Travel Regulation System TEMPORARY DUTY (TDY) TRAVEL... the standard data elements and when must they be captured on a travel accounting system? The data...

KSC-08pd2387

NASA Image and Video Library

2008-08-12

CAPE CANAVERAL, Fla. – In the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center, technicians monitor the lifting of the Soft Capture Mechanism (SCM), part of the Soft Capture and Rendezvous System, or SCRS, from its shipping container. The SCRS will enable the future rendezvous, capture and safe disposal of Hubble by either a crewed or robotic mission. The ring-like device attaches to Hubble’s aft bulkhead. The SCRS greatly increases the current shuttle capture interfaces on Hubble, therefore significantly reducing the rendezvous and capture design complexities associated with the disposal mission. The SCRS comprises the Soft Capture Mechanism system and the Relative Navigation System and is part of the payload on the fifth and final Hubble servicing mission, STS-125, targeted for launch Oct. 8. Photo credit: NASA/Jack Pfaller

Evaluating the capabilities of aerosol-to-liquid particle extraction system (ALPXS)/ICP-MS for monitoring trace metals in indoor air.

PubMed

Jayawardene, Innocent; Rasmussen, Pat E; Chenier, Marc; Gardner, H David

2014-09-01

This study investigates the application of the Aerosol-to-Liquid Particle Extraction System (ALPXS), which uses wet electrostatic precipitation to collect airborne particles, for multi-element indoor stationary monitoring. Optimum conditions are determined for capturing airborne particles for metal determination by inductively coupled plasma-mass spectrometry (ICP-MS), for measuring field blanks, and for calculating limits of detection (LOD) and quantification (LOQ). Due to the relatively high flow rate (300 L min(-1)), a sampling duration of 1 hr to 2 hr was adequate to capture airborne particle-bound metals under the investigated experimental conditions. The performance of the ALPXS during a building renovation demonstrated signal-to-noise ratios appropriate for sampling airborne particles in environments with elevated metal concentrations, such as workplace settings. The ALPXS shows promise as a research tool for providing useful information on short-term variations (transient signals) and for trapping particles into aqueous solutions where needed for subsequent characterization. As the ALPXS does not provide size-specific samples, and its efficiency at different flow rates has yet to be quantified, the ALPXS would not replace standard filter-based protocols accepted for regulatory applications (e.g., exposure measurements), but rather would provide additional information if used in conjunction with filter based methods. Implications: This study investigates the capability of the Aerosol-to-Liquid Particle Extraction System (ALPXS) for stationary sampling of airborne metals in indoor workplace environments, with subsequent analysis by ICP-MS. The high flow rate (300 L/min) permits a short sampling duration (< 2 hr). Results indicated that the ALPXS was capable of monitoring short-term changes in metal emissions during a renovation activity. This portable instrument may prove to be advantageous in occupational settings as a qualitative indicator of elevated concentrations of airborne metals at short time scales.

Sequence Capture versus Restriction Site Associated DNA Sequencing for Shallow Systematics.

PubMed

Harvey, Michael G; Smith, Brian Tilston; Glenn, Travis C; Faircloth, Brant C; Brumfield, Robb T

2016-09-01

Sequence capture and restriction site associated DNA sequencing (RAD-Seq) are two genomic enrichment strategies for applying next-generation sequencing technologies to systematics studies. At shallow timescales, such as within species, RAD-Seq has been widely adopted among researchers, although there has been little discussion of the potential limitations and benefits of RAD-Seq and sequence capture. We discuss a series of issues that may impact the utility of sequence capture and RAD-Seq data for shallow systematics in non-model species. We review prior studies that used both methods, and investigate differences between the methods by re-analyzing existing RAD-Seq and sequence capture data sets from a Neotropical bird (Xenops minutus). We suggest that the strengths of RAD-Seq data sets for shallow systematics are the wide dispersion of markers across the genome, the relative ease and cost of laboratory work, the deep coverage and read overlap at recovered loci, and the high overall information that results. Sequence capture's benefits include flexibility and repeatability in the genomic regions targeted, success using low-quality samples, more straightforward read orthology assessment, and higher per-locus information content. The utility of a method in systematics, however, rests not only on its performance within a study, but on the comparability of data sets and inferences with those of prior work. In RAD-Seq data sets, comparability is compromised by low overlap of orthologous markers across species and the sensitivity of genetic diversity in a data set to an interaction between the level of natural heterozygosity in the samples examined and the parameters used for orthology assessment. In contrast, sequence capture of conserved genomic regions permits interrogation of the same loci across divergent species, which is preferable for maintaining comparability among data sets and studies for the purpose of drawing general conclusions about the impact of historical processes across biotas. We argue that sequence capture should be given greater attention as a method of obtaining data for studies in shallow systematics and comparative phylogeography. © The Author(s) 2016. Published by Oxford University Press, on behalf of the Society of Systematic Biologists. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

NPDES Permits for Phase 2 Stormwater Program in Puerto Rico

EPA Pesticide Factsheets

EPA's 1999 stormwater Phase II regulations established small municipal separate storm sewer systems (MS4s) in urbanized areas, and small MS4s outside the urbanized areas that are designated by the permitting authority, to obtain NPDES permit coverage.

40 CFR 122.6 - Continuation of expiring permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Continuation of expiring permits. 122.6 Section 122.6 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Definitions and...

40 CFR 122.6 - Continuation of expiring permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Continuation of expiring permits. 122.6 Section 122.6 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Definitions and...

40 CFR 122.5 - Effect of a permit.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Effect of a permit. 122.5 Section 122.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Definitions and General...

40 CFR 122.5 - Effect of a permit.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Effect of a permit. 122.5 Section 122.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS EPA ADMINISTERED PERMIT PROGRAMS: THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Definitions and General...

40 CFR 63.3100 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... be in compliance with the operating limits for emission capture systems and add-on control devices...) You must maintain a log detailing the operation and maintenance of the emission capture systems, add... capture system and add-on control device performance tests have been completed, as specified in § 63.3160...

40 CFR 63.3100 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... be in compliance with the operating limits for emission capture systems and add-on control devices...) You must maintain a log detailing the operation and maintenance of the emission capture systems, add... capture system and add-on control device performance tests have been completed, as specified in § 63.3160...

40 CFR 63.3100 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... be in compliance with the operating limits for emission capture systems and add-on control devices...) You must maintain a log detailing the operation and maintenance of the emission capture systems, add... capture system and add-on control device performance tests have been completed, as specified in § 63.3160...

Acceptance and Use of Lecture Capture System (LCS) in Executive Business Studies: Extending UTAUT2

ERIC Educational Resources Information Center

Farooq, Muhammad Shoaib; Salam, Maimoona; Jaafar, Norizan; Fayolle, Alain; Ayupp, Kartinah; Radovic-Markovic, Mirjana; Sajid, Ali

2017-01-01

Purpose: Adoption of latest technological advancements (e.g. lecture capture system) is a hallmark of market-driven private universities. Among many other distinguishing features, lecture capture system (LCS) is the one which is being offered to enhance the flexibility of learning environment for attracting executive business students. Majority of…

An in vitro study of magnetic particle targeting in small blood vessels

NASA Astrophysics Data System (ADS)

Udrea, Laura Elena; Strachan, Norval J. C.; Bădescu, Vasile; Rotariu, Ovidiu

2006-10-01

The magnetic guidance and capture of particles inside the human body, via the circulatory system, is a novel method for the targeted delivery of drugs. This experimental study confirms in vitro that a dipolar capturing device, based on high-energy magnets with an active space of 8.7 cm × 10 cm × 10 cm, retains colloidal magnetic particles (MPs) (<30 nm) injected in the capillary tubes, where flow velocities are comparable to that encountered in the capillary beds of tumours (<0.5 cm s-1). The build-up of the deposition of the MPs was investigated using video imaging techniques that enabled continuous monitoring of the blocking of the vessel whilst simultaneously recording the colloid's flow rate. The parameters of practical importance (length of MP deposit, time of capillary blocking) were estimated and were found to be dependent on the initial fluid velocity, the MP concentration and the distance between the capillary tube and the polar magnetic pieces. Although the tube used in this experiment is larger (diameter = 0.75 mm, length = 100 mm) than that of real capillaries (diameter = 0.01 mm, length ~1.5 mm), the flow velocities chosen were similar to those encountered in the capillary beds of tumours and the length/diameter ratio was approximately equal (133 for the present set-up, 100-150 for real capillaries). In these circumstances and using the same magnetic field conditions (intensity, gradient) and MPs, there is close similarity with magnetic capture in a microscopic capillary system. Moreover, the macroscopic system permits analysis of the distribution of MPs in the active magnetic space, and consequently the maximum targetable volume. This study revealed that the capture of particles within the active space was strongly influenced by the gradient of the magnetic field and the flow velocity. Thus, when the magnetic field gradient had medium values (0.1-0.3 T cm-1) and the fluid velocity was small (0.15 cm s-1), the particles were captured in small, compact and stable deposits (L < 4 cm) and the time necessary for blocking of the capillary was <150 s. Doubling the value for the flow velocity did not influence significantly either the length of MP deposits nor the blocking time. However, lower gradients (<0.1 T cm-1) and larger velocities (0.3-0.9 cm s-1) result in the formation of larger deposits (4 cm < L < 10 cm) that are unstable at the beginning of the capture process. These large deposits do become stable given sufficient time for the deposition process to take place in conjunction with a decrease in the flow rate. As a consequence, the time necessary for blocking of the capillary increased up to 450 s. Decreasing the MP concentration from 0.02 g cm-3 to 0.005 g cm-3 decreased the deposit lengths by approximately 20% and doubled the values of the blocking time. The maximum targetable volume obtained by the present method is ~350 cm3, which corresponds to medium-sized tumours. The capillary vessels were blocked only for the situation that occurs for microcirculation within a tumour. This reduces the concentration of MPs trapped within the normal tissues, which occurs when using particles of micrometre size. This work showed the potential of using colloidal MPs and dipolar magnetic devices for treatment of human patients, when the affected sites are positioned at medium distances from the surface of the body (e.g. head, neck, breast, hands and legs).

Ship-in-a-bottle synthesis of amine-functionalized ionic liquids in NaY zeolite for CO2 capture

PubMed Central

Yu, Yinghao; Mai, Jingzhang; Wang, Lefu; Li, Xuehui; Jiang, Zheng; Wang, Furong

2014-01-01

CO2 capture on solid materials possesses significant advantages on the operation cost, process for large-scale CO2 capture and storage (CCS) that stimulates great interest in exploring high-performance solid CO2 adsorbents. A ship-in-a-bottle strategy was successfully developed to prepare the [APMIM]Br@NaY host–guest system in which an amine-functionalized ionic liquid (IL), 1-aminopropyl-3-methylimidazolium bromide ([APMIM]Br), was in-situ encapsulated in the NaY supercages. The genuine host-guest systems were thoroughly characterized and tested in CO2 capture from simulated flue gas. It was evidenced the encapsulated ILs are more stable than the bulk ILs. These host–guest systems exhibited superb overall CO2 capture capacity up to 4.94 mmol g−1 and the chemically adsorbed CO2 achieved 1.85 mmol g−1 depending on the [APMIM]Br loading amount. The chemisorbed CO2 can be desorbed rapidly by flushing with N2 gas at 50°C. The optimized [APMIM]Br@NaY system remains its original CO2 capture capacity in multiple cycling tests under prolonged harsh adsorption-desorption conditions. The excellent physicochemical properties and the CO2 capture performance of the host-guest systems offer them great promise for the future practice in the industrial CO2 capture. PMID:25104324

NPDES Draft Permit for Standing Rock Rural Water System in South Dakota

EPA Pesticide Factsheets

Under NPDES draft permit SD-0030996, the Standing Rock Rural Water System is authorized to discharge from its wastewater treatment facility in Corson County, South Dakota, to an unnamed tributary to Oahe Reservoir on the Missouri River.

System for exchanging tools and end effectors on a robot

DOEpatents

Burry, David B.; Williams, Paul M.

1991-02-19

A system and method for exchanging tools and end effectors on a robot permits exchange during a programmed task. The exchange mechanism is located off the robot, thus reducing the mass of the robot arm and permitting smaller robots to perform designated tasks. A simple spring/collet mechanism mounted on the robot is used which permits the engagement and disengagement of the tool or end effector without the need for a rotational orientation of the tool to the end effector/collet interface. As the tool changing system is not located on the robot arm no umbilical cords are located on robot.

Provenance Datasets Highlighting Capture Disparities

DTIC Science & Technology

2014-01-01

Vistrails [20], Taverna [21] or Kepler [6], and an OS -observing system like PASS [18]. In less granular workflow systems, the data files, scripts...run, etc. are capturable as long as they are executed within the workflow system. In more granular OS -observing systems, the actual reads, writes...rolling up” very granular information to less granular information. OS -level capture knows that a socket was opened and that data was sent to a foreign

Large Advanced Space Systems (LASS) computer-aided design program additions

NASA Technical Reports Server (NTRS)

Farrell, C. E.

1982-01-01

The LSS preliminary and conceptual design requires extensive iteractive analysis because of the effects of structural, thermal, and control intercoupling. A computer aided design program that will permit integrating and interfacing of required large space system (LSS) analyses is discussed. The primary objective of this program is the implementation of modeling techniques and analysis algorithms that permit interactive design and tradeoff studies of LSS concepts. Eight software modules were added to the program. The existing rigid body controls module was modified to include solar pressure effects. The new model generator modules and appendage synthesizer module are integrated (interfaced) to permit interactive definition and generation of LSS concepts. The mass properties module permits interactive specification of discrete masses and their locations. The other modules permit interactive analysis of orbital transfer requirements, antenna primary beam n, and attitude control requirements.

Reference manual for data base on Nevada water-rights permits

USGS Publications Warehouse

Cartier, K.D.; Bauer, E.M.; Farnham, J.L.

1995-01-01

The U.S. Geological Survey and Nevada Division of Water Resources have cooperatively developed and implemented a data-base system for managing water-rights permit information for the State of Nevada. The Water-Rights Permit data base is part of an integrated system of computer data bases using the Ingres Relational Data-Base Manage-ment System, which allows efficient storage and access to water information from the State Engineer's office. The data base contains a main table, three ancillary tables, and five lookup tables, as well as a menu-driven system for entering, updating, and reporting on the data. This reference guide outlines the general functions of the system and provides a brief description of data tables and data-entry screens.

Techno-economic assessment of polymer membrane systems for postcombustion carbon capture at coal-fired power plants.

PubMed

Zhai, Haibo; Rubin, Edward S

2013-03-19

This study investigates the feasibility of polymer membrane systems for postcombustion carbon dioxide (CO(2)) capture at coal-fired power plants. Using newly developed performance and cost models, our analysis shows that membrane systems configured with multiple stages or steps are capable of meeting capture targets of 90% CO(2) removal efficiency and 95+% product purity. A combined driving force design using both compressors and vacuum pumps is most effective for reducing the cost of CO(2) avoided. Further reductions in the overall system energy penalty and cost can be obtained by recycling a portion of CO(2) via a two-stage, two-step membrane configuration with air sweep to increase the CO(2) partial pressure of feed flue gas. For a typical plant with carbon capture and storage, this yielded a 15% lower cost per metric ton of CO(2) avoided compared to a plant using a current amine-based capture system. A series of parametric analyses also is undertaken to identify paths for enhancing the viability of membrane-based capture technology.

Separation and dual detection of prostate cancer cells and protein biomarkers using a microchip device.

PubMed

Huang, Wanfeng; Chang, Chun-Li; Brault, Norman D; Gur, Onur; Wang, Zhe; Jalal, Shadia I; Low, Philip S; Ratliff, Timothy L; Pili, Roberto; Savran, Cagri A

2017-01-31

Current efforts for the detection of prostate cancer using only prostate specific antigen are not ideal and indicate a need to develop new assays - using multiple targets - that can more accurately stratify disease states. We previously introduced a device capable of the concurrent detection of cellular and molecular markers from a single sample fluid. Here, an improved design, which achieves affinity as well as size-based separation of captured targets using antibody-conjugated magnetic beads and a silicon chip containing micro-apertures, is presented. Upon injection of the sample, the integration of magnetic attraction with the micro-aperture chip permits larger cell-bead complexes to be isolated in an upper chamber with the smaller protein-bead complexes and remaining beads passing through the micro-apertures into the lower chamber. This enhances captured cell purity for on chip quantification, allows the separate retrieval of captured cells and proteins for downstream analysis, and enables higher bead concentrations for improved multiplexed ligand targeting. Using LNCaP cells and prostate specific membrane antigen (PSMA) to model prostate cancer, the device was able to detect 34 pM of spiked PSMA and achieve a cell capture efficiency of 93% from culture media. LNCaP cells and PSMA were then spiked into diluted healthy human blood to mimic a cancer patient. The device enabled the detection of spiked PSMA (relative to endogenous PSMA) while recovering 85-90% of LNCaP cells which illustrated the potential of new assays for the diagnosis of prostate cancer.

Biomedical health assessments of the Florida manatee in Crystal River - providing opportunities for training during the capture, handling, and processing of this endangered aquatic mammal

USGS Publications Warehouse

Bonde, Robert K.; Garrett, Andrew; Belanger, Michael; Askin, Nesime; Tan, Luke; Wittnich, Carin

2012-01-01

Federal and state researchers have been involved in manatee (Trichechus manatus) biomedical health assessment programs for a couple of decades. These benchmark studies have provided a foundation for the development of consistent capture, handling, and processing techniques and protocols. Biologists have implemented training and encouraged multi-agency participation whenever possible to ensure reliable data acquisition, recording, sample collection, publication integrity, and meeting rigorous archival standards. Under a U.S. Fish and Wildlife Service wildlife research permit granted to the U.S. Geological Survey (USGS) Sirenia Project, federal biologists and collaborators are allowed to conduct research studies on wild and captive manatees detailing various aspects of their biology. Therefore, researchers with the project have been collaborating on numerous studies over the last several years. One extensive study, initiated in 2006 has focused on health and fitness of the winter manatee population located in Crystal River, Florida. During those health assessments, capture, handling, and work-up training has been afforded to many of the participants. That study has successfully captured and handled 123 manatees. The data gathered have provided baseline information on manatee health, reproductive status, and nutritional condition. This research initiative addresses concerns and priorities outlined in the Florida Manatee Recovery Plan. The assessment teams strive to continue this collaborative effort to help advance our understanding of health-related issues confronting manatees throughout their range and interlacing these findings with surrogate species concepts.

Real-time POD-CFD Wind-Load Calculator for PV Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huayamave, Victor; Divo, Eduardo; Ceballos, Andres

The primary objective of this project is to create an accurate web-based real-time wind-load calculator. This is of paramount importance for (1) the rapid and accurate assessments of the uplift and downforce loads on a PV mounting system, (2) identifying viable solutions from available mounting systems, and therefore helping reduce the cost of mounting hardware and installation. Wind loading calculations for structures are currently performed according to the American Society of Civil Engineers/ Structural Engineering Institute Standard ASCE/SEI 7; the values in this standard were calculated from simplified models that do not necessarily take into account relevant characteristics such asmore » those from full 3D effects, end effects, turbulence generation and dissipation, as well as minor effects derived from shear forces on installation brackets and other accessories. This standard does not include provisions that address the special requirements of rooftop PV systems, and attempts to apply this standard may lead to significant design errors as wind loads are incorrectly estimated. Therefore, an accurate calculator would be of paramount importance for the preliminary assessments of the uplift and downforce loads on a PV mounting system, identifying viable solutions from available mounting systems, and therefore helping reduce the cost of the mounting system and installation. The challenge is that although a full-fledged three-dimensional computational fluid dynamics (CFD) analysis would properly and accurately capture the complete physical effects of air flow over PV systems, it would be impractical for this tool, which is intended to be a real-time web-based calculator. CFD routinely requires enormous computation times to arrive at solutions that can be deemed accurate and grid-independent even in powerful and massively parallel computer platforms. This work is expected not only to accelerate solar deployment nationwide, but also help reach the SunShot Initiative goals of reducing the total installed cost of solar energy systems by 75%. The largest percentage of the total installed cost of solar energy system is associated with balance of system cost, with up to 40% going to “soft” costs; which include customer acquisition, financing, contracting, permitting, interconnection, inspection, installation, performance, operations, and maintenance. The calculator that is being developed will provide wind loads in real-time for any solar system designs and suggest the proper installation configuration and hardware; and therefore, it is anticipated to reduce system design, installation and permitting costs.« less

40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2010 CFR

2010-07-01

... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

40 CFR 63.4167 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.4167 Section 63... capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4092 according to this section unless you have received approval...

40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2013 CFR

2013-07-01

... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

40 CFR 63.4567 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.4567 Section 63... emission capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4492 according to this section, unless you have received...

40 CFR 63.3967 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.3967 Section 63... establish the emission capture system and add-on control device operating limits during the performance test... must establish the operating limits required by § 63.3892 according to this section, unless you have...

40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2011 CFR

2011-07-01

... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

40 CFR 63.4167 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.4167 Section 63... capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4092 according to this section unless you have received approval...

40 CFR 63.4767 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2014 CFR

2014-07-01

... capture system and add-on control device operating limits during the performance test? 63.4767 Section 63... capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4692 according to this section, unless you have received...

40 CFR 63.4767 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.4767 Section 63... capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4692 according to this section, unless you have received...

40 CFR 63.3967 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.3967 Section 63... establish the emission capture system and add-on control device operating limits during the performance test... must establish the operating limits required by § 63.3892 according to this section, unless you have...

40 CFR 63.4567 - How do I establish the emission capture system and add-on control device operating limits during...

Code of Federal Regulations, 2012 CFR

2012-07-01

... capture system and add-on control device operating limits during the performance test? 63.4567 Section 63... emission capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.4492 according to this section, unless you have received...

NPDES Permit for NIST Boulder Laboratories Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Under NPDES permit CO-R042002,NIST is authorized to discharge from all municipal separate storm sewer outfalls existing as of the effective date of this permit to receiving waters within the exterior boundaries of the Boulder Laboratories in Boulder, Colo.

NPDES Permit for Lower Brule Wastewater Lagoon System in South Dakota

EPA Pesticide Factsheets

Under NPDES permit number SD-0020800, Lower Brule Rural Water is authorized to discharge from its wastewater lagoon system serving the town of Lower Brule, located in Lyman County, South Dakota, to the bank of the Missouri River (Lake Sharpe).

NPDES Permit for Denver Federal Center Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Denver Federal Center Municipal Separate Storm Sewer System is authorized to discharge from all municipal separate storm sewer outfalls existing as of the effective date of permit CO-R042004 to receiving waters Lakewood, Jefferson County, Colorado.

Occipital TMS at phosphene detection threshold captures attention automatically.

PubMed

Rangelov, Dragan; Müller, Hermann J; Taylor, Paul C J

2015-04-01

Strong stimuli may capture attention automatically, suggesting that attentional selection is determined primarily by physical stimulus properties. The mechanisms underlying capture remain controversial, in particular, whether feedforward subcortical processes are its main source. Also, it remains unclear whether only physical stimulus properties determine capture strength. Here, we demonstrate strong capture in the absence of feedforward input to subcortical structures such as the superior colliculus, by using transcranial magnetic stimulation (TMS) over occipital visual cortex as an attention cue. This implies that the feedforward sweep through subcortex is not necessary for capture to occur but rather provides an additional source of capture. Furthermore, seen cues captured attention more strongly than (physically identical) unseen cues, suggesting that the momentary state of the nervous system modulates attentional selection. In summary, we demonstrate the existence of several sources of attentional capture, and that both physical stimulus properties and the state of the nervous system influence capture. Copyright © 2015 Elsevier Inc. All rights reserved.

Manual for the Construction of a Mercury Capture System for Use in Gold Shops

EPA Pesticide Factsheets

Download a manual for the construction of a mercury capture system for use in gold shops with detailed information for constructing a device to capture mercury aerosol particles emitted from gold shops that process gold dore’, a gold-mercury amalgam.

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

30 CFR 773.4 - Requirements to obtain permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER... a State, no person shall engage in or carry out any surface coal mining operations, unless such... (b) of this section. A permittee need not renew the permit if no surface coal mining operations will...

NPDES Permit for Buckley Air Force Base Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Under NPDES permit CO-R042003, the U.S. Air Force is authorized to discharge from all MS4 outfalls existing as of the effective date of this permit to specified receiving waters within the exterior boundaries of Buckley Air Force Base, in Aurora, Colorado

48 CFR 52.247-2 - Permits, Authorities, or Franchises.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

48 CFR 52.247-2 - Permits, Authorities, or Franchises.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

48 CFR 52.247-2 - Permits, Authorities, or Franchises.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

48 CFR 52.247-2 - Permits, Authorities, or Franchises.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

48 CFR 52.247-2 - Permits, Authorities, or Franchises.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

300 area TEDF NPDES Permit Compliance Monitoring Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loll, C.M.

1995-09-05

This document presents the 300 Area Treated Effluent Disposal Facility (TEDF) National Pollutant Discharge Elimination System (NPDES) Permit Compliance Monitoring Plan (MP). The MP describes how ongoing monitoring of the TEDF effluent stream for compliance with the NPDES permit will occur. The MP also includes Quality Assurance protocols to be followed.

NPDES Permit for Fort Carson Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

Under NPDES permit CO-R042001, Fort Carson is authorized to discharge from all municipal separate storm sewer system outfalls to receiving waters which include B-Ditch, Clover Ditch, Infantry Creek, Rock Creek, and others in El Paso County, Colorado.

Tracking B-Cell Repertoires and Clonal Histories in Normal and Malignant Lymphocytes.

PubMed

Weston-Bell, Nicola J; Cowan, Graeme; Sahota, Surinder S

2017-01-01

Methods for tracking B-cell repertoires and clonal history in normal and malignant B-cells based on immunoglobulin variable region (IGV) gene analysis have developed rapidly with the advent of massive parallel next-generation sequencing (mpNGS) protocols. mpNGS permits a depth of analysis of IGV genes not hitherto feasible, and presents challenges of bioinformatics analysis, which can be readily met by current pipelines. This strategy offers a potential resolution of B-cell usage at a depth that may capture fully the natural state, in a given biological setting. Conventional methods based on RT-PCR amplification and Sanger sequencing are also available where mpNGS is not accessible. Each method offers distinct advantages. Conventional methods for IGV gene sequencing are readily adaptable to most laboratories and provide an ease of analysis to capture salient features of B-cell use. This chapter describes two methods in detail for analysis of IGV genes, mpNGS and conventional RT-PCR with Sanger sequencing.

Barriers and Prospects of Carbon Sequestration in India.

PubMed

Gupta, Anjali; Nema, Arvind K

2014-04-01

Carbon sequestration is considered a leading technology for reducing carbon dioxide (CO2) emissions from fossil-fuel based electricity generating power plants and could permit the continued use of coal and gas whilst meeting greenhouse gas targets. India will become the world's third largest emitter of CO2 by 2015. Considering the dependence of health of the Indian global economy, there is an imperative need to develop a global approach which could address the capturing and securely storing carbon dioxide emitted from an array of energy. Therefore technology such as carbon sequestration will deliver significant CO2 reductions in a timely fashion. Considerable energy is required for the capture, compression, transport and storage steps. With the availability of potential technical storage methods for carbon sequestration like forest, mineral and geological storage options with India, it would facilitate achieving stabilization goal in the near future. This paper examines the potential carbon sequestration options available in India and evaluates them with respect to their strengths, weakness, threats and future prospects.

A Phosphoenzyme Mimic, Overlapping Catalytic Sites and Reaction Coordinate Motion for Human NAMPT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burgos, E.; Ho, M; Almo, S

2009-01-01

Nicotinamide phosphoribosyltransferase (NAMPT) is highly evolved to capture nicotinamide (NAM) and replenish the nicotinamide adenine dinucleotide (NAD+) pool during ADP-ribosylation and transferase reactions. ATP-phosphorylation of an active-site histidine causes catalytic activation, increasing NAM affinity by 160,000. Crystal structures of NAMPT with catalytic site ligands identify the phosphorylation site, establish its role in catalysis, demonstrate unique overlapping ATP and phosphoribosyltransferase sites, and establish reaction coordinate motion. NAMPT structures with beryllium fluoride indicate a covalent H247-BeF3- as the phosphohistidine mimic. Activation of NAMPT by H247-phosphorylation causes stabilization of the enzyme-phosphoribosylpyrophosphate complex, permitting efficient capture of NAM. Reactant and product structures establish reactionmore » coordinate motion for NAMPT to be migration of the ribosyl anomeric carbon from the pyrophosphate leaving group to the nicotinamide-N1 while the 5-phosphoryl group, the pyrophosphate moiety, and the nicotinamide ring remain fixed in the catalytic site.« less

A preliminary investigation of cryogenic CO2 capture utilizing a reverse Brayton Cycle

NASA Astrophysics Data System (ADS)

Yuan, L. C.; Pfotenhauer, J. M.; Qiu, L. M.

2014-01-01

Utilizing CO2 capture and storage (CCS) technologies is a significant way to reduce carbon emissions from coal fired power plants. Cryogenic CO2 capture (CCC) is an innovative and promising CO2 capture technology, which has an apparent energy and environmental advantage compared to alternatives. A process of capturing CO2 from the flue gas of a coal-fired electrical power plant by cryogenically desublimating CO2 has been discussed and demonstrated theoretically. However, pressurizing the inlet flue gas to reduce the energy penalty for the cryogenic process will lead to a more complex system. In this paper, a modified CCC system utilizing a reverse Brayton Cycle is proposed, and the energy penalty of these two systems are compared theoretically.

40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2014 CFR

2014-07-01

... to Subpart OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2014 CFR

2014-07-01

...—Operating Limits if Using Add-On Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

Code of Federal Regulations, 2014 CFR

2014-07-01

...—Operating Limits if Using Add-on Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits for Capture Systems... 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits in the following table...

40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2011 CFR

2011-07-01

... Limits if Using Add-On Control Devices and Capture System If you are required to comply with operating... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2012 CFR

2012-07-01

...—Operating Limits if Using Add-On Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2013 CFR

2013-07-01

... to Subpart OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Operating Limits for Capture Systems... 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits in the following table...

40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

Code of Federal Regulations, 2013 CFR

2013-07-01

...—Operating Limits if Using Add-on Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2012 CFR

2012-07-01

... to Subpart OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2010 CFR

2010-07-01

... OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you are required... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

Code of Federal Regulations, 2012 CFR

2012-07-01

...—Operating Limits if Using Add-on Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Operating Limits for Capture Systems... Subpart IIII of Part 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits...

40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Operating Limits for Capture Systems... Subpart IIII of Part 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits...

40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

Code of Federal Regulations, 2011 CFR

2011-07-01

... Using Add-on Control Devices and Capture System If you are required to comply with operating limits by... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2011 CFR

2011-07-01

... OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you are required... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

Code of Federal Regulations, 2010 CFR

2010-07-01

... Using Add-on Control Devices and Capture System If you are required to comply with operating limits by... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2013 CFR

2013-07-01

...—Operating Limits if Using Add-On Control Devices and Capture System If you are required to comply with... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Operating Limits for Capture Systems... Subpart IIII of Part 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits...

40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

Code of Federal Regulations, 2010 CFR

2010-07-01

... Limits if Using Add-On Control Devices and Capture System If you are required to comply with operating... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

Application of a multistate model to estimate culvert effects on movement of small fishes

USGS Publications Warehouse

Norman, J.R.; Hagler, M.M.; Freeman, Mary C.; Freeman, B.J.

2009-01-01

While it is widely acknowledged that culverted road-stream crossings may impede fish passage, effects of culverts on movement of nongame and small-bodied fishes have not been extensively studied and studies generally have not accounted for spatial variation in capture probabilities. We estimated probabilities for upstream and downstream movement of small (30-120 mm standard length) benthic and water column fishes across stream reaches with and without culverts at four road-stream crossings over a 4-6-week period. Movement and reach-specific capture probabilities were estimated using multistate capture-recapture models. Although none of the culverts were complete barriers to passage, only a bottomless-box culvert appeared to permit unrestricted upstream and downstream movements by benthic fishes based on model estimates of movement probabilities. At two box culverts that were perched above the water surface at base flow, observed movements were limited to water column fishes and to intervals when runoff from storm events raised water levels above the perched level. Only a single fish was observed to move through a partially embedded pipe culvert. Estimates for probabilities of movement over distances equal to at least the length of one culvert were low (e.g., generally ???0.03, estimated for 1-2-week intervals) and had wide 95% confidence intervals as a consequence of few observed movements to nonadjacent reaches. Estimates of capture probabilities varied among reaches by a factor of 2 to over 10, illustrating the importance of accounting for spatially variable capture rates when estimating movement probabilities with capture-recapture data. Longer-term studies are needed to evaluate temporal variability in stream fish passage at culverts (e.g., in relation to streamflow variability) and to thereby better quantify the degree of population fragmentation caused by road-stream crossings with culverts. ?? American Fisheries Society 2009.

SYSTEM LEVEL IMPLICATIONS OF FLEXIBLE CO2 CAPTURE OPERATION

EPA Science Inventory

In ERCOT, turning flexible CO₂ capture systems off during infrequent periods of peak electricity demand can avoid hundreds of millions to billions of dollars in capital costs to replace the power output lost to CO₂ capture energy requirements.  When CO...

System for exchanging tools and end effectors on a robot

DOEpatents

Burry, D.B.; Williams, P.M.

1991-02-19

A system and method for exchanging tools and end effectors on a robot permits exchange during a programmed task. The exchange mechanism is located off the robot, thus reducing the mass of the robot arm and permitting smaller robots to perform designated tasks. A simple spring/collet mechanism mounted on the robot is used which permits the engagement and disengagement of the tool or end effector without the need for a rotational orientation of the tool to the end effector/collet interface. As the tool changing system is not located on the robot arm no umbilical cords are located on robot. 12 figures.

Initial characterization of the large genome of the salamander Ambystoma mexicanum using shotgun and laser capture chromosome sequencing

PubMed Central

Keinath, Melissa C.; Timoshevskiy, Vladimir A.; Timoshevskaya, Nataliya Y.; Tsonis, Panagiotis A.; Voss, S. Randal; Smith, Jeramiah J.

2015-01-01

Vertebrates exhibit substantial diversity in genome size, and some of the largest genomes exist in species that uniquely inform diverse areas of basic and biomedical research. For example, the salamander Ambystoma mexicanum (the Mexican axolotl) is a model organism for studies of regeneration, development and genome evolution, yet its genome is ~10× larger than the human genome. As part of a hierarchical approach toward improving genome resources for the species, we generated 600 Gb of shotgun sequence data and developed methods for sequencing individual laser-captured chromosomes. Based on these data, we estimate that the A. mexicanum genome is ~32 Gb. Notably, as much as 19 Gb of the A. mexicanum genome can potentially be considered single copy, which presumably reflects the evolutionary diversification of mobile elements that accumulated during an ancient episode of genome expansion. Chromosome-targeted sequencing permitted the development of assemblies within the constraints of modern computational platforms, allowed us to place 2062 genes on the two smallest A. mexicanum chromosomes and resolves key events in the history of vertebrate genome evolution. Our analyses show that the capture and sequencing of individual chromosomes is likely to provide valuable information for the systematic sequencing, assembly and scaffolding of large genomes. PMID:26553646

Initial characterization of the large genome of the salamander Ambystoma mexicanum using shotgun and laser capture chromosome sequencing.

PubMed

Keinath, Melissa C; Timoshevskiy, Vladimir A; Timoshevskaya, Nataliya Y; Tsonis, Panagiotis A; Voss, S Randal; Smith, Jeramiah J

2015-11-10

Vertebrates exhibit substantial diversity in genome size, and some of the largest genomes exist in species that uniquely inform diverse areas of basic and biomedical research. For example, the salamander Ambystoma mexicanum (the Mexican axolotl) is a model organism for studies of regeneration, development and genome evolution, yet its genome is ~10× larger than the human genome. As part of a hierarchical approach toward improving genome resources for the species, we generated 600 Gb of shotgun sequence data and developed methods for sequencing individual laser-captured chromosomes. Based on these data, we estimate that the A. mexicanum genome is ~32 Gb. Notably, as much as 19 Gb of the A. mexicanum genome can potentially be considered single copy, which presumably reflects the evolutionary diversification of mobile elements that accumulated during an ancient episode of genome expansion. Chromosome-targeted sequencing permitted the development of assemblies within the constraints of modern computational platforms, allowed us to place 2062 genes on the two smallest A. mexicanum chromosomes and resolves key events in the history of vertebrate genome evolution. Our analyses show that the capture and sequencing of individual chromosomes is likely to provide valuable information for the systematic sequencing, assembly and scaffolding of large genomes.

Detection and correction of patient movement in prostate brachytherapy seed reconstruction

NASA Astrophysics Data System (ADS)

Lam, Steve T.; Cho, Paul S.; Marks, Robert J., II; Narayanan, Sreeram

2005-05-01

Intraoperative dosimetry of prostate brachytherapy can help optimize the dose distribution and potentially improve clinical outcome. Evaluation of dose distribution during the seed implant procedure requires the knowledge of 3D seed coordinates. Fluoroscopy-based seed localization is a viable option. From three x-ray projections obtained at different gantry angles, 3D seed positions can be determined. However, when local anaesthesia is used for prostate brachytherapy, the patient movement during fluoroscopy image capture becomes a practical problem. If uncorrected, the errors introduced by patient motion between image captures would cause seed mismatches. Subsequently, the seed reconstruction algorithm would either fail to reconstruct or yield erroneous results. We have developed an algorithm that permits detection and correction of patient movement that may occur between fluoroscopy image captures. The patient movement is decomposed into translational shifts along the tabletop and rotation about an axis perpendicular to the tabletop. The property of spatial invariance of the co-planar imaging geometry is used for lateral movement correction. Cranio-caudal movement is corrected by analysing the perspective invariance along the x-ray axis. Rotation is estimated by an iterative method. The method can detect and correct for the range of patient movement commonly seen in the clinical environment. The algorithm has been implemented for routine clinical use as the preprocessing step for seed reconstruction.

Apparent diffusive motion of centrin foci in living cells: implications for diffusion-based motion in centriole duplication

NASA Astrophysics Data System (ADS)

Rafelski, Susanne M.; Keller, Lani C.; Alberts, Jonathan B.; Marshall, Wallace F.

2011-04-01

The degree to which diffusion contributes to positioning cellular structures is an open question. Here we investigate the question of whether diffusive motion of centrin granules would allow them to interact with the mother centriole. The role of centrin granules in centriole duplication remains unclear, but some proposed functions of these granules, for example, in providing pre-assembled centriole subunits, or by acting as unstable 'pre-centrioles' that need to be captured by the mother centriole (La Terra et al 2005 J. Cell Biol. 168 713-22), require the centrin foci to reach the mother. To test whether diffusive motion could permit such interactions in the necessary time scale, we measured the motion of centrin-containing foci in living human U2OS cells. We found that these centrin foci display apparently diffusive undirected motion. Using the apparent diffusion constant obtained from these measurements, we calculated the time scale required for diffusion to capture by the mother centrioles and found that it would greatly exceed the time available in the cell cycle. We conclude that mechanisms invoking centrin foci capture by the mother, whether as a pre-centriole or as a source of components to support later assembly, would require a form of directed motility of centrin foci that has not yet been observed.

Response of Integrated CO 2 Capture and Storage Systems in Saline Aquifers and Fractured Shale Formations to Changes in CO 2 Capture Costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langenfeld, Julie K.; Bielicki, Jeffrey M.; Tao, Zhiyuan

Fractured shale formations are new potential target reservoirs for CO 2 capture and storage (CCS) and provide several potential advantages over storage in saline aquifers in terms of storage capacity, leakage risk, and cost savings from brownfield development. Here, we used a geospatial-optimization, engineering-economic model to investigate the sensitivity of integrated CCS networks in Ohio, Pennsylvania, and West Virginia to reductions in CO 2 capture costs. The resulting reductions in CO 2 capture costs were based on hypothetical cases where technological innovation reduced CO 2 capture costs. There were also small differences in the spatial organization of the CCS deploymentmore » when the capture costs were reduced. We also found that the percent reduction in average cost of CCS systems became smaller as the CO 2 capture costs were decreased.« less

Response of Integrated CO 2 Capture and Storage Systems in Saline Aquifers and Fractured Shale Formations to Changes in CO 2 Capture Costs

DOE PAGES

Langenfeld, Julie K.; Bielicki, Jeffrey M.; Tao, Zhiyuan; ...

2017-08-18

Fractured shale formations are new potential target reservoirs for CO 2 capture and storage (CCS) and provide several potential advantages over storage in saline aquifers in terms of storage capacity, leakage risk, and cost savings from brownfield development. Here, we used a geospatial-optimization, engineering-economic model to investigate the sensitivity of integrated CCS networks in Ohio, Pennsylvania, and West Virginia to reductions in CO 2 capture costs. The resulting reductions in CO 2 capture costs were based on hypothetical cases where technological innovation reduced CO 2 capture costs. There were also small differences in the spatial organization of the CCS deploymentmore » when the capture costs were reduced. We also found that the percent reduction in average cost of CCS systems became smaller as the CO 2 capture costs were decreased.« less

Pilot testing of a membrane system for postcombustion CO 2 capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merkel, Tim; Kniep, Jay; Wei, Xiaotong

2015-09-30

This final report summarizes work conducted for the U.S. Department of Energy, National Energy Technology Laboratory (DOE) to scale up an efficient post-combustion CO 2 capture membrane process to the small pilot test stage (award number DE-FE0005795). The primary goal of this research program was to design, fabricate, and operate a membrane CO 2 capture system to treat coal-derived flue gas containing 20 tonnes CO 2/day (20 TPD). Membrane Technology and Research (MTR) conducted this project in collaboration with Babcock and Wilcox (B&W), the Electric Power Research Institute (EPRI), WorleyParsons (WP), the Illinois Sustainable Technology Center (ISTC), Enerkem (EK), andmore » the National Carbon Capture Center (NCCC). In addition to the small pilot design, build and slipstream testing at NCCC, other project efforts included laboratory membrane and module development at MTR, validation field testing on a 1 TPD membrane system at NCCC, boiler modeling and testing at B&W, a techno-economic analysis (TEA) by EPRI/WP, a case study of the membrane technology applied to a ~20 MWe power plant by ISTC, and an industrial CO 2 capture test at an Enerkem waste-to-biofuel facility. The 20 TPD small pilot membrane system built in this project successfully completed over 1,000 hours of operation treating flue gas at NCCC. The Polaris™ membranes used on this system demonstrated stable performance, and when combined with over 10,000 hours of operation at NCCC on a 1 TPD system, the risk associated with uncertainty in the durability of postcombustion capture membranes has been greatly reduced. Moreover, next-generation Polaris membranes with higher performance and lower cost were validation tested on the 1 TPD system. The 20 TPD system also demonstrated successful operation of a new low-pressure-drop sweep module that will reduce parasitic energy losses at full scale by as much as 10 MWe. In modeling and pilot boiler testing, B&W confirmed the viability of CO 2 recycle to the boiler as envisioned in the MTR process design. The impact of this CO 2 recycle on boiler efficiency was quantified and incorporated into a TEA of the membrane capture process applied to a full-scale power plant. As with previous studies, the TEA showed the membrane process to be lower cost than the conventional solvent capture process even at 90% CO 2capture. A sensitivity study indicates that the membrane capture cost decreases significantly if the 90% capture requirement is relaxed. Depending on the process design, a minimum capture cost is achieved at 30-60% capture, values that would meet proposed CO 2 emission regulations for coal-fired power plants. In summary, this project has successfully advanced the MTR membrane capture process through small pilot testing (technology readiness level 6). The technology is ready for future scale-up to the 10 MWe size.« less

NPDES Permit for Peterson Air Force Base Municipal Separate Storm Sewer System in Colorado

EPA Pesticide Factsheets

NPDES permit CO-R042006, authorizes Peterson AFB to discharge from all municipal separate storm sewer system outfalls to receiving waters which include the East Fork of Sand Creek and others within exterior AFB boundaries in El Paso County, Colorado.