Science.gov

Sample records for carine adleri film

  1. A Reanalysis of the CARIN Theory of Conceptual Combination

    ERIC Educational Resources Information Center

    Maguire, Phil; Devereux, Barry; Costello, Fintan; Cater, Arthur

    2007-01-01

    The competition among relations in nominals (CARIN) theory of conceptual combination (C. L. Gagne & E. J. Shoben, 1997) proposes that people interpret nominal compounds by selecting a relation from a pool of competing alternatives and that relation availability is influenced by the frequency with which relations have been previously associated…

  2. Tracheal Resection With Carinal Reconstruction for Squamous Cell Carcinoma.

    PubMed

    Lancaster, Timothy S; Krantz, Seth B; Patterson, G Alexander

    2016-07-01

    Surgical resection is the treatment of choice for primary malignancies of the trachea. We present here the rare case of a lifelong nonsmoker with primary squamous cell carcinoma of the trachea, requiring tracheal resection and anterior carinal reconstruction. Patient preparation, surgical technique, and considerations to avoid airway anastomotic complications are discussed.

  3. Uniportal video-assisted thoracoscopic bronchoplastic and carinal sleeve procedures.

    PubMed

    Gonzalez-Rivas, Diego; Yang, Yang; Sekhniaidze, Dmitrii; Stupnik, Tomaz; Fernandez, Ricardo; Lei, Jiang; Zhu, Yuming; Jiang, Gening

    2016-03-01

    Despite of the recent advanced with the video-assisted thoracoscopic surgery (VATS), the most common approach for bronchial and carinal resection is still the open surgery. The technical difficulties, the steep learning curve and the concerns about performing an oncologic and safe reconstruction in advanced cases, are the main reasons for the low adoption of VATS for sleeve resections. Most of the authors use 3-4 incisions for thoracoscopic sleeve procedures. However these surgical techniques can be performed by a single incision approach by skilled uniportal VATS surgeons. The improvements of the surgical instruments, high definition cameras and recent 3D systems have greatly contributed to facilitate the adoption of uniportal VATS techniques for sleeve procedures. In this article we describe the technique of thoracoscopic bronchial sleeve, bronchovascular and carinal resections through a single incision approach. PMID:26981273

  4. CARIN Theory Reanalysis Reanalyzed: A Comment on Maguire, Devereux, Costello, and Cater (2007)

    ERIC Educational Resources Information Center

    Spalding, Thomas L.; Gagne, Christina L.

    2008-01-01

    P. Maguire, B. Devereux, F. Costello, and A. Cater discussed the Gagne and Shoben (1997) CARIN theory of conceptual combination and, after presenting a sample drawn from the British National Corpus and comparing the two corpora, concluded that the Gagne and Shoben corpus is too small and unrepresentative. They then discussed the mathematical model…

  5. An Analysis of the Alleged Skeletal Remains of Carin Göring

    PubMed Central

    Kjellström, Anna; Edlund, Hanna; Lembring, Maria; Ahlgren, Viktoria; Allen, Marie

    2012-01-01

    In 1991, treasure hunters found skeletal remains in an area close to the destroyed country residence of former Nazi leader Hermann Göring in northeastern Berlin. The remains, which were believed to belong to Carin Göring, who was buried at the site, were examined to determine whether it was possible to make a positive identification. The anthropological analysis showed that the remains come from an adult woman. The DNA analysis of several bone elements showed female sex, and a reference sample from Carin's son revealed mtDNA sequences identical to the remains. The profile has one nucleotide difference from the Cambridge reference sequence (rCRS), the common variant 263G. A database search resulted in a frequency of this mtDNA sequence of about 10% out of more than 7,000 European haplotypes. The mtDNA sequence found in the ulna, the cranium and the reference sample is, thus, very common among Europeans. Therefore, nuclear DNA analysis was attempted. The remains as well as a sample from Carin's son were successfully analysed for the three nuclear markers TH01, D7S820 and D8S1179. The nuclear DNA analysis of the two samples revealed one shared allele for each of the three markers, supporting a mother and son relationship. This genetic information together with anthropological and historical files provides an additional piece of circumstantial evidence in our efforts to identify the remains of Carin Göring. PMID:23284605

  6. An analysis of the alleged skeletal remains of Carin Göring.

    PubMed

    Kjellström, Anna; Edlund, Hanna; Lembring, Maria; Ahlgren, Viktoria; Allen, Marie

    2012-01-01

    In 1991, treasure hunters found skeletal remains in an area close to the destroyed country residence of former Nazi leader Hermann Göring in northeastern Berlin. The remains, which were believed to belong to Carin Göring, who was buried at the site, were examined to determine whether it was possible to make a positive identification. The anthropological analysis showed that the remains come from an adult woman. The DNA analysis of several bone elements showed female sex, and a reference sample from Carin's son revealed mtDNA sequences identical to the remains. The profile has one nucleotide difference from the Cambridge reference sequence (rCRS), the common variant 263G. A database search resulted in a frequency of this mtDNA sequence of about 10% out of more than 7,000 European haplotypes. The mtDNA sequence found in the ulna, the cranium and the reference sample is, thus, very common among Europeans. Therefore, nuclear DNA analysis was attempted. The remains as well as a sample from Carin's son were successfully analysed for the three nuclear markers TH01, D7S820 and D8S1179. The nuclear DNA analysis of the two samples revealed one shared allele for each of the three markers, supporting a mother and son relationship. This genetic information together with anthropological and historical files provides an additional piece of circumstantial evidence in our efforts to identify the remains of Carin Göring.

  7. An extensin-rich matrix lines the carinal canals in Equisetum ramosissimum, which may function as water-conducting channels

    PubMed Central

    Leroux, O.; Knox, J. P.; Masschaele, B.; Bagniewska-Zadworna, A.; Marcus, S. E.; Claeys, M.; van Hoorebeke, L.; Viane, R. L. L.

    2011-01-01

    Background and Aims The anatomy of Equisetum stems is characterized by the occurrence of vallecular and carinal canals. Previous studies on the carinal canals in several Equisetum species suggest that they convey water from one node to another. Methods Cell wall composition and ultrastructure have been studied using immunocytochemistry and electron microscopy, respectively. Serial sectioning and X-ray computed tomography were employed to examine the internode–node–internode transition of Equisetum ramosissimum. Key Results The distribution of the LM1 and JIM20 extensin epitopes is restricted to the lining of carinal canals. The monoclonal antibodies JIM5 and LM19 directed against homogalacturonan with a low degree of methyl esterification and the CBM3a probe recognizing crystalline cellulose also bound to this lining. The xyloglucan epitopes recognized by LM15 and CCRC-M1 were only detected in this lining after pectate lyase treatment. The carinal canals, connecting consecutive rings of nodal xylem, are formed by the disruption and dissolution of protoxylem elements during elongation of the internodes. Their inner surface appears smooth compared with that of vallecular canals. Conclusions The carinal canals in E. ramosissimum have a distinctive lining containing pectic homogalacturonan, cellulose, xyloglucan and extensin. These canals might function as water-conducting channels which would be especially important during the elongation of the internodes when protoxylem is disrupted and the metaxylem is not yet differentiated. How the molecularly distinct lining relates to the proposed water-conducting function of the carinal canals requires further study. Efforts to elucidate the spatial and temporal distribution of cell wall polymers in a taxonomically broad range of plants will probably provide more insight into the structural–functional relationships of individual cell wall components or of specific configurations of cell wall polymers. PMID:21752793

  8. Monitoreo fotométrico de η Carinæ desde el OALP Temporadas de observación 2011-2012

    NASA Astrophysics Data System (ADS)

    Fernández-Lajús, E.; Giudici, F. N.; Ramos, X. S.; Scalia, M. C.; Salerno, N. E.

    η Carinæ is the brightest Luminous Blue Variable in our Galaxy, and is one of the most intriguing stellar objects of the sky because of its historic and spectacular brightness variations. In particular η Car presents photometric events that repeat with a periodicity of 5.54 years. To analyze this periodic behavior and other features in their light curves, we performed since 2003 a long-term CCD monitoring at the La Plata Observatory. In this work we present the light curves resulting from observing seasons 2011 and 2012. FULL TEXT IN SPANISH

  9. Personality and ectoparasitic mites (Hemipteroseius adleri) in firebugs (Pyrrhocoris apterus).

    PubMed

    Gyuris, Enikő; Hankó, Júlia Fruzsina; Feró, Orsolya; Barta, Zoltán

    2016-01-01

    Individuals of the same species often consistently differ in their behaviour across time and context. These stable differences are usually termed 'animal personality'. Parasitism is known to significantly influence the evolution of animal personality at least in part because more explorative individuals may meet parasites more frequently than less explorative ones. Previously, we have demonstrated that consistent individual differences (i.e. boldness, activity, exploration) can be measured in firebugs. As continuation, we examined here the relationship between firebug personality traits and their ectoparasitic mite loads in a wild population. We showed that bugs that behaved in a more explorative way have more mites and we also found a marginally significant interaction between sex, boldness and activity: bolder and more active female firebugs were more infected. In addition, we experimentally tested whether an artificial infection causes any alteration in the bug's behaviour and whether there is any relationship between firebug personality and immune response. This treatment did not induce any alteration in bugs' personality. We found that bugs become more explorative but less active when repeating the experiment, but at the same time all personality traits (boldness, activity and exploration) were repeatable. Furthermore, firebugs with a stronger immune response behaved more boldly but also less actively. PMID:26569455

  10. Personality and ectoparasitic mites (Hemipteroseius adleri) in firebugs (Pyrrhocoris apterus).

    PubMed

    Gyuris, Enikő; Hankó, Júlia Fruzsina; Feró, Orsolya; Barta, Zoltán

    2016-01-01

    Individuals of the same species often consistently differ in their behaviour across time and context. These stable differences are usually termed 'animal personality'. Parasitism is known to significantly influence the evolution of animal personality at least in part because more explorative individuals may meet parasites more frequently than less explorative ones. Previously, we have demonstrated that consistent individual differences (i.e. boldness, activity, exploration) can be measured in firebugs. As continuation, we examined here the relationship between firebug personality traits and their ectoparasitic mite loads in a wild population. We showed that bugs that behaved in a more explorative way have more mites and we also found a marginally significant interaction between sex, boldness and activity: bolder and more active female firebugs were more infected. In addition, we experimentally tested whether an artificial infection causes any alteration in the bug's behaviour and whether there is any relationship between firebug personality and immune response. This treatment did not induce any alteration in bugs' personality. We found that bugs become more explorative but less active when repeating the experiment, but at the same time all personality traits (boldness, activity and exploration) were repeatable. Furthermore, firebugs with a stronger immune response behaved more boldly but also less actively.

  11. Film Reviews.

    ERIC Educational Resources Information Center

    Lance, Larry M.; Atwater, Lynn

    1987-01-01

    Reviews four Human Sexuality films and videos. These are: "Personal Decisions" (Planned Parenthood Federation of America, 1985); "The Touch Film" (Sterling Production, 1986); "Rethinking Rape" (Film Distribution Center, 1985); "Not A Love Story" (National Film Board of Canada, 1981). (AEM)

  12. Film Boxes.

    ERIC Educational Resources Information Center

    Osterer, Irv

    2002-01-01

    Presents an art lesson in which students created three-dimensional designs for 35mm film packages to improve graphic arts learning. Describes how the students examined and created film boxes using QuarkXPress software. (CMK)

  13. Film Reviews

    ERIC Educational Resources Information Center

    Dowling, John, Ed.

    1976-01-01

    Reviews five instructional films on: P-N junctions; crystal diodes; nuclear fusion research; Schlieren photography; and the energy crisis; including discussions of solar, nuclear, and fossil fuel energy. Also lists numerous other available films. (MLH)

  14. Nanocomposite films

    DOEpatents

    Mitlin, David; , Ophus, Colin; Evoy, Stephane; Radmilovic, Velimir; Mohammadi, Reza; Westra, Ken; Nelson-Fitzpatrick, Nathaniel; Lee, Zonghoon

    2010-07-20

    A thin-film composition of nanocrystal molybdenum in an amorphous metallic matrix may be formed by co-sputtering Mo with aluminum or nickel. NEMS cantilevers may be formed from the film. The films exhibit high nanoindentation hardness and a reduction in roughness and intrinsic stress, while maintaining resistivity in the metallic range.

  15. On Film

    ERIC Educational Resources Information Center

    Watts, Marty

    2006-01-01

    In this article, the author discusses the role of window films in enhancing indoor air quality in schools. Historically, window film has been used to reduce temperatures in buildings prone to overheating. Too much solar energy entering through windows makes occupants uncomfortable and air conditioning more costly. Film has been a simple solution…

  16. Humanistic Films.

    ERIC Educational Resources Information Center

    Gaffney, Maureen, Ed.

    1981-01-01

    Designed for media specialists and educators, this issue includes seven articles focusing on humanistic films for children. Following a brief editorial encouraging the ideals of humanism, the first article presents an analysis of seven films with positive sex-role models. Included is a model for evaluating children's films. The second article…

  17. Anodic films

    SciTech Connect

    Muller, R.H.

    1983-08-01

    Surface layers are formed on many metals by anodic reaction. Such layers include the products of charge and discharge in many storage batteries, dielectric films used in electronic and optical circuits and display devices, layers responsible for passivity and corrosion protection, and films generated in metal shaping and finishing operations such as anodization, coloring, electropolishing, electrochemical machining and deburring. Anodic films are formed by solid-solid transformations or by dissolution-precipitation processes. Film properties and mechanisms of formation can be determined in situ by a number of optical techniques which have recently become available.

  18. Film ispalators

    SciTech Connect

    Startsev, Aleksandr V; Stoilov, Yurii Yu

    2002-05-31

    New physical objects, ispalators based on free soap films, exhibit persistent flows of the soap solution in open and closed volumes in air with additions of gases of the C{sub 8}F{sub 18} type (p = 20 Torr) at temperature drops on the films of the order of tenths and hundredths of kelvin. The flows move continuously at a velocity of 5 - 20 cm s{sup -1}. It is found that the parts of an inclined ispalator film show anomalous behaviour upon heating: their weight increases and they move downward over the film, whereas the unheated parts of the film move upward. Continuous radial vortex flows accompanied by the formation and washing of the regions of a thin black film are observed on circular films in closed volumes upon their uniform external cooling by evaporating water for 5 - 10 hours. The rapid flows make film ispalators the efficient heat carriers, which operate at small temperature drops (tenths and hundredths of kelvin) and surpass copper in the amount of thermal energy being transferred. The outlook for the further study and applications of film ispalators for detecting thermal fields and laser radiation is discussed. (laser applications and other topics in quantum electronics)

  19. About Films.

    ERIC Educational Resources Information Center

    Christman, Robert; Krockover, Gerald H.

    1984-01-01

    Lists and briefly describes 46 college-level films. Films are arranged in the following categories: volcanism and earthquakes; plate tectonics; energy, water, and environmental concerns; petroleum and coal; astronomy; space exploration, space shuttle; paleontology; geomorphology; and mineralogy, petrology, and economic geology. (BC)

  20. Thin Film?

    NASA Astrophysics Data System (ADS)

    Kariper, İ. Afşin

    2014-09-01

    This study focuses on the critical surface tension of lead sulfite (PbSO3) crystalline thin film produced with chemical bath deposition on substrates (commercial glass).The PbSO3 thin films were deposited at room temperature at different deposition times. The structural properties of the films were defined and examined according to X-ray diffraction (XRD) and the XRD results such as dislocation density, average grain size, and no. of crystallites per unit area. Atomic force microscopy was used to measure the film thickness and the surface properties. The critical surface tension of the PbSO3 thin films was measured with an optical tensiometer instrument and calculated using the Zisman method. The results indicated that the critical surface tension of films changed in accordance with the average grain size and film thickness. The film thickness increased with deposition time and was inversely correlated with surface tension. The average grain size increased according to deposition time and was inversely correlated with surface tension.

  1. Film Makers On Film Making.

    ERIC Educational Resources Information Center

    Geduld, Harry M., Ed.

    This collection includes essays by and interviews with more than 30 film-makers, both classic and contemporary, on the subjects of their major interests and procedures in making films. The directors are: Louis Lumiere, Cecil Hepworth, Edwin S. Porter, Mack Sennett, David W. Griffith, Robert Flaherty, Charles Chaplin, Eric von Stroheim, Dziga…

  2. Polymer films

    DOEpatents

    Granick, Steve; Sukhishvili, Svetlana A.

    2008-12-30

    A film contains a first polymer having a plurality of hydrogen bond donating moieties, and a second polymer having a plurality of hydrogen bond accepting moieties. The second polymer is hydrogen bonded to the first polymer.

  3. Polymer films

    DOEpatents

    Granick, Steve; Sukhishvili, Svetlana A.

    2004-05-25

    A film contains a first polymer having a plurality of hydrogen bond donating moieties, and a second polymer having a plurality of hydrogen bond accepting moieties. The second polymer is hydrogen bonded to the first polymer.

  4. Piezoelectric Film.

    ERIC Educational Resources Information Center

    Garrison, Steve

    1992-01-01

    Presents activities that utilize piezoelectric film to familiarize students with fundamental principles of electricity. Describes classroom projects involving chemical sensors, microbalances, microphones, switches, infrared sensors, and power generation. (MDH)

  5. Film Reviews

    ERIC Educational Resources Information Center

    Ladd, George T.

    1974-01-01

    Briefly describes films about the following topics: water cycles, the energy crisis, the eruption of Mt. Aetna, the hot springs of Yellowstone National Park, and methods of using pine cones to determine the ages of ancient civilizations. (MLH)

  6. Film Credits

    ERIC Educational Resources Information Center

    Borja, Rhea R.

    2006-01-01

    With the advent of easy-to-use digital technology, schools are responding to the interests of their media-savvy students by offering more courses in filmmaking. In this article, the author features different films produced by students. Among other things, she discusses the students' growing interest in filmmaking.

  7. Black Films and Film-Makers.

    ERIC Educational Resources Information Center

    Patterson, Lindsay, Ed.

    The development of black films and the attitudes of the film industry toward black films and black actors are some of the topics examined in this anthology of essays. Section 1, "Nigger to Supernigger," contains such articles as "The Death of Rastus: Negroes in American Films" by Thomas R. Cripps and "Folk Values in a New Medium" by Alain Locke…

  8. Film and History.

    ERIC Educational Resources Information Center

    Schaber, Robin L.

    2002-01-01

    Provides an annotated bibliography of Web sites that focus on using film to teach history. Includes Web sites in five areas: (1) film and education; (2) history of cinema; (3) film and history resources; (4) film and women; and (5) film organizations. (CMK)

  9. Film: An Introduction.

    ERIC Educational Resources Information Center

    Fell, John L.

    "Understanding Film," the opening section of this book, discusses perceptions of and responses to film and the way in which experiences with and knowledge of other media affect film viewing. The second section, "Film Elements," analyzes the basic elements of film: the use of space and time, the impact of editing, sound and color, and the effects…

  10. Ferroelectric ultrathin perovskite films

    DOEpatents

    Rappe, Andrew M; Kolpak, Alexie Michelle

    2013-12-10

    Disclosed herein are perovskite ferroelectric thin-film. Also disclosed are methods of controlling the properties of ferroelectric thin films. These films can be used in a variety materials and devices, such as catalysts and storage media, respectively.

  11. [Films: China and Japan].

    ERIC Educational Resources Information Center

    Gumport, Roberta H.

    The history of filmmaking in China and Japan and film usage in teaching are considered in this document. Pointing out how films describe historical context and culture, the document also describes various techniques of film making. Films in China were heavily influenced by western models and have tended to be tools of the power structure, as…

  12. A Festival of Films.

    ERIC Educational Resources Information Center

    National Association for the Education of Young Children, Washington, DC.

    This catalogue consists of an alphabetical listing of more than 200 films, each with an annotation including a brief description of the film, intended audience, and length of film (most running from about 10 to 30 minutes). Titles were selected by Film Preview Committees of the National Association for the Education of Young Children. A list of…

  13. Carbon thin film thermometry

    NASA Technical Reports Server (NTRS)

    Collier, R. S.; Sparks, L. L.; Strobridge, T. R.

    1973-01-01

    The work concerning carbon thin film thermometry is reported. Optimum film deposition parameters were sought on an empirical basis for maximum stability of the films. One hundred films were fabricated for use at the Marshall Space Flight Center; 10 of these films were given a precise quasi-continuous calibration of temperature vs. resistance with 22 intervals between 5 and 80 K using primary platinum and germanium thermometers. Sensitivity curves were established and the remaining 90 films were given a three point calibration and fitted to the established sensitivity curves. Hydrogen gas-liquid discrimination set points are given for each film.

  14. The Educational Film Industry

    ERIC Educational Resources Information Center

    Tortora, Vincent R.; Schillaci, Peter

    1975-01-01

    Increased dialog is needed among educational film producers, distributors, and consumers in order to be sure that what is being produced meets educators' needs and also to help solve the financial problems of the film industry. (LS)

  15. Film as Film; Understanding and Judging Movies.

    ERIC Educational Resources Information Center

    Perkins, V. F.

    The criteria for judging movies which are presented here are based on the belief that film criticism becomes rational, if not "objective", when it displays and inspects the nature of its evidence and the bases of its arguments. The author dissents from the view of early film theorists that montage is the essence of cinema, and that cinema is to be…

  16. Literature and Film.

    ERIC Educational Resources Information Center

    Richardson, Robert

    The differences, similarities, and common goals of film and literature, as well as the ways in which each form and its associated criticism is able to illuminate the other, are discussed in this book. Individual chapters are "Literature and Film,""Literary Origins and Backgrounds of the Film,""Griffith and Eisenstein: The Uses of Literature in…

  17. Film Resources on Japan.

    ERIC Educational Resources Information Center

    Michigan Univ., Ann Arbor. Audio-Visual Education Center.

    Sixteen millimeter motion pictures dealing with Japan are listed alphabetically by title and annotated. Length of film, whether color or black and white, and name of producer or distributor is given for each, and a subject index is provided. Films produced before 1960, "sponsored" films, and 35 mm filmstrips are listed without annotations. A list…

  18. Using Folktale Films.

    ERIC Educational Resources Information Center

    Fuchs, Merrill Lee; Gaffney, Maureen

    1982-01-01

    A model user's guide for the film, "The Frog King or Faithful Henry," introduces media specialists and educators to the range of possibilities for developing different activities for different objectives and age levels from a single film. An introductory article provides a synopsis of the film, rationale for its choice as a model, a discussion of…

  19. Health Careers Film Guide.

    ERIC Educational Resources Information Center

    National Institutes of Health (DHEW), Bethesda, MD. Bureau of Health Manpower Education.

    This document, which represents a survey of the entire health career film field, was designed to provide information for people interested in a health career. The guide indicates that a major criteria for film selection was recency; however, some older films that give a fairly accurate image of a profession were included, with some emphasis given…

  20. Marine Science Film Catalogue.

    ERIC Educational Resources Information Center

    Chapman, Frank L.

    Forty-eight motion picture films and filmstrips in the field of marine science are catalogued in this booklet. Following the alphabetical index, one page is devoted to each film indicating its type, producer, recommended grade level, running time, and presence of color and/or sound. A summary of film content, possible uses, and outstanding…

  1. Introduction to Film Making.

    ERIC Educational Resources Information Center

    Davis, Robert E.

    This booklet is intended for teachers who are now teaching units in film production as part of a program in communication or who wish to begin work with filmmaking in such a program. The first section is intended to serve as a brief introduction to film theory, while a major portion of the rest of the booklet is devoted to film projects which may…

  2. Australian Film Studies.

    ERIC Educational Resources Information Center

    Breen, Myles P.

    Although Australia had a vigorous film industry in the silent film era, it was stifled in the 1930s when United States and British interests bought up the Australian distribution channels and closed down the indigenous industry. However, the industry and film study have undergone a renaissance since the advent of the Labor government in 1972,…

  3. Focus on Shakespearean Films.

    ERIC Educational Resources Information Center

    Eckert, Charles W., Ed.

    This is an anthology of reviews and critical pieces of the significant and available Shakespearean films made between 1935 and 1966. Included are three general essays on Shakespearean film by Ian Johnson, Henri Lemaitre, and Geoffrey Reeves. The specific films and their reviewers are: A Midsummer's Night Dream (1935) Allardyce Nicoll and Richard…

  4. The Language of Film.

    ERIC Educational Resources Information Center

    Whitaker, Rod

    This book, designed for the film maker, critic, and serious filmgoer, explores elements of filmic expression from the creative and perceptual points of view. Chapters (1) trace the linguistic and mechanical development of film, (2) discuss the contributions of image and sound to film content, (3) suggest the contributions of editing and montage,…

  5. 99 Films on Drugs.

    ERIC Educational Resources Information Center

    Weber, David O., Ed.

    This catalog describes and evaluates 16-millimeter films about various aspects of drug use. Among the subjects covered by the 99 films are the composition and effects of different drugs, reasons why people use drugs, life in the drug culture, the problem of law enforcement, and various means of dealing with drug users. Each film is synopsized. Two…

  6. Thick Film Interference.

    ERIC Educational Resources Information Center

    Trefil, James

    1983-01-01

    Discusses why interference effects cannot be seen with a thick film, starting with a review of the origin of interference patterns in thin films. Considers properties of materials in films, properties of the light source, and the nature of light. (JN)

  7. Getting into Film.

    ERIC Educational Resources Information Center

    London, Mel

    This book describes the various aspects of the film industry and the many jobs related to filmmaking, stressing that no "formula" exists for finding a successful career in the film industry. Chapters provide information on production, writing for film, cinematography, editing, music, sound, animation and graphics, acting and modeling, the "unsung…

  8. Pyrolyzed thin film carbon

    NASA Technical Reports Server (NTRS)

    Tai, Yu-Chong (Inventor); Liger, Matthieu (Inventor); Harder, Theodore (Inventor); Konishi, Satoshi (Inventor); Miserendino, Scott (Inventor)

    2010-01-01

    A method of making carbon thin films comprises depositing a catalyst on a substrate, depositing a hydrocarbon in contact with the catalyst and pyrolyzing the hydrocarbon. A method of controlling a carbon thin film density comprises etching a cavity into a substrate, depositing a hydrocarbon into the cavity, and pyrolyzing the hydrocarbon while in the cavity to form a carbon thin film. Controlling a carbon thin film density is achieved by changing the volume of the cavity. Methods of making carbon containing patterned structures are also provided. Carbon thin films and carbon containing patterned structures can be used in NEMS, MEMS, liquid chromatography, and sensor devices.

  9. Chronicles of foam films.

    PubMed

    Gochev, G; Platikanov, D; Miller, R

    2016-07-01

    The history of the scientific research on foam films, traditionally known as soap films, dates back to as early as the late 17th century when Boyle and Hooke paid special attention to the colours of soap bubbles. Their inspiration was transferred to Newton, who began systematic study of the science of foam films. Over the next centuries, a number of scientists dealt with the open questions of the drainage, stability and thickness of foam films. The significant contributions of Plateau and Gibbs in the middle/late 19th century are particularly recognized. After the "colours" method of Newton, Reinold and Rücker as well as Johhonnot developed optical methods for measuring the thickness of the thinner "non-colour" films (first order black) that are still in use today. At the beginning of the 20th century, various aspects of the foam film science were elucidated by the works of Dewar and Perrin and later by Mysels. Undoubtedly, the introduction of the disjoining pressure by Derjaguin and the manifestation of the DLVO theory in describing the film stability are considered as milestones in the theoretical development of foam films. The study of foam films gained momentum with the introduction of the microscopic foam film methodology by Scheludko and Exerowa, which is widely used today. This historical perspective serves as a guide through the chronological development of knowledge on foam films achieved over several centuries.

  10. Chronicles of foam films.

    PubMed

    Gochev, G; Platikanov, D; Miller, R

    2016-07-01

    The history of the scientific research on foam films, traditionally known as soap films, dates back to as early as the late 17th century when Boyle and Hooke paid special attention to the colours of soap bubbles. Their inspiration was transferred to Newton, who began systematic study of the science of foam films. Over the next centuries, a number of scientists dealt with the open questions of the drainage, stability and thickness of foam films. The significant contributions of Plateau and Gibbs in the middle/late 19th century are particularly recognized. After the "colours" method of Newton, Reinold and Rücker as well as Johhonnot developed optical methods for measuring the thickness of the thinner "non-colour" films (first order black) that are still in use today. At the beginning of the 20th century, various aspects of the foam film science were elucidated by the works of Dewar and Perrin and later by Mysels. Undoubtedly, the introduction of the disjoining pressure by Derjaguin and the manifestation of the DLVO theory in describing the film stability are considered as milestones in the theoretical development of foam films. The study of foam films gained momentum with the introduction of the microscopic foam film methodology by Scheludko and Exerowa, which is widely used today. This historical perspective serves as a guide through the chronological development of knowledge on foam films achieved over several centuries. PMID:26361708

  11. Thin film composite actuators

    NASA Astrophysics Data System (ADS)

    Su, Quanmin; Kim, Taesung; Zheng, Yun; Wuttig, Manfred R.

    1995-05-01

    The mechanical properties of Ni50Ti50 deposited on Si substrates were studied focussing on the interaction of the film and substrate. This interaction determines the transformation characteristics through interface accommodation and mechanical constraints exerted by the substrate stiffness. Substrate stiffness, controlled by the film/substrate thickness ratio, was found to have a substantial influence on the output energy of the film/substrate composite. A switch type composite based on this knowledge was fabricated and tested. The thermo-mechanical properties of Terfenol-D thin films deposited on Si substrates were studied by static and dynamic measurements of film/substrate composite cantilevers. The Curie transition, (Delta) E effect and mechanical damping of the film were measured simultaneously. The stress in the film was controlled by annealing below the recrystallization temperature and determined to vary from -500 MPa, compression, in as deposited films to +480 MPa, tension, in annealed films. The Curie temperature shifts from 80 degree(s)C to 140 degree(s)C as the tension increases while the structure of the film remains amorphous. The stress change induced by annealing also drastically effects the film's damping characteristics. The (Delta) E effect of the amorphous material, about 20%, was used to estimate the magnetostriction, (lambda) s approximately equals 4 (DOT) 10-3.

  12. Ceramic Composite Thin Films

    NASA Technical Reports Server (NTRS)

    Ruoff, Rodney S. (Inventor); Stankovich, Sasha (Inventor); Dikin, Dmitriy A. (Inventor); Nguyen, SonBinh T. (Inventor)

    2013-01-01

    A ceramic composite thin film or layer includes individual graphene oxide and/or electrically conductive graphene sheets dispersed in a ceramic (e.g. silica) matrix. The thin film or layer can be electrically conductive film or layer depending the amount of graphene sheets present. The composite films or layers are transparent, chemically inert and compatible with both glass and hydrophilic SiOx/silicon substrates. The composite film or layer can be produced by making a suspension of graphene oxide sheet fragments, introducing a silica-precursor or silica to the suspension to form a sol, depositing the sol on a substrate as thin film or layer, at least partially reducing the graphene oxide sheets to conductive graphene sheets, and thermally consolidating the thin film or layer to form a silica matrix in which the graphene oxide and/or graphene sheets are dispersed.

  13. Coating of plasma polymerized film

    NASA Technical Reports Server (NTRS)

    Morita, S.; Ishibashi, S.

    1980-01-01

    Plasma polymerized thin film coating and the use of other coatings is suggested for passivation film, thin film used for conducting light, and solid body lubrication film of dielectrics of ultra insulators for electrical conduction, electron accessories, etc. The special features of flow discharge development and the polymerized film growth mechanism are discussed.

  14. Documentary Elements in Early Films.

    ERIC Educational Resources Information Center

    Sanderson, Richard A.

    Focusing on documentary elements, this study examines the film content and film techniques of 681 motion pictures produced in the United States prior to 1904. Analysis of films by type, subject matter, and trends in subject matter shows that one-third of the early films are documentary in type and three-fourths of the films use subject matter of a…

  15. Renaissance of the Film.

    ERIC Educational Resources Information Center

    Bellone, Julius, Ed.

    The post-World War II period was one of the liveliest in the history of the cinema. This is a collection of 33 critical articles on some of the best films of the perd. Most of the essays explicate the themes and symbols of the films. The essays deal with these films: "The Apu Trilogy,""L'Avventura,""Balthazar,""Blow-Up,""Bonnie and Clyde," Citizen…

  16. Clinical careers film.

    PubMed

    2015-09-01

    Those interested in developing clinical academic careers might be interested in a short animated film by Health Education England (HEE) and the National Institute for Health Research. The three-minute film, a frame from which is shown below, describes the sort of opportunities that are on offer to all professionals as part of the HEE's clinical academic careers framework. You can view the film on YouTube at tinyurl.com/pelb95c. PMID:26309005

  17. Protective overcoating of films

    NASA Technical Reports Server (NTRS)

    Maas, K. A.

    1972-01-01

    Kodak Film Type SO-212 was emulsion overcoated with gelatin and lacquer to evaluate the feasibility of application of the coatings, any image degradation, and the relative protection offered against abrasion. Evaluated were: Eastman motion picture film lacquer Type 485, water solutions of Eastman purified Calfskin gelatin, and experimental Eastman gelatin stripping film of 4 and 6 microns. Conclusions reached were: (1) All coatings can be applied with relative ease with the only limitation being that of equipment. (2) None of the coatings degrade the processed image. (3) All of the coatings provide protection to the emulsion. These conclusions apply to any film which may be considered for overcoating.

  18. Microfilm--Which Film Type, Which Application?

    ERIC Educational Resources Information Center

    Dodson, Suzanne Cates

    1985-01-01

    Report on characteristics of different kinds of microfilm available indicates proper film for specific needs. Silver halide and nonsilver films, diazo film, vesicular film, reaction of films to light, effect of heat and humidity on films, film susceptibility to scratching, and potential longevity of film types are covered. (35 references) (EJS)

  19. Thin film calorimetry of polymer films

    NASA Astrophysics Data System (ADS)

    Zhang, Wenhua; Rafailovich, Miriam; Sokolov, Jonathan; Salamon, William

    2000-03-01

    Polystryene and polymethylmethacrylate films for thicknesses ranging from 50nm to 500nm using a direct calorimetric technique (Lai et al, App. Phys. Lett. 67, p9(1995)). Samples were deposited on Ni foils(2-2.5um) and placed in a high vacuum oven. Calibrated heat pulses were input to the polymer films by current pulses to the Ni substrate and temperature changes were determined from the change in Ni resistance. Pulses producing temperature jumps of 3-8K were used and signal averaging over pulses reduced noise levels enough to identify glass transitions down to 50nm. Molecular weight dependence of thick films Tg was used as a temperature calibration.

  20. Thin-film forces in pseudoemulsion films

    SciTech Connect

    Bergeron, V.; Radke, C.J. |

    1991-06-01

    Use of foam for enhanced oil recovery (EOR) has shown recent success in steam-flooding field applications. Foam can also provide an effective barrier against gas coning in thin oil zones. Both of these applications stem from the unique mobility-control properties a stable foam possesses when it exists in porous media. Unfortunately, oil has a major destabilizing effect on foam. Therefore, it is important for EOR applications to understand how oil destroys foam. Studies all indicate that stabilization of the pseudoemulsion film is critical to maintain foam stability in the presence of oil. Hence, to aid in design of surfactant formulations for foam insensitivity to oil the authors pursue direct measurement of the thin-film or disjoining forces that stabilize pseudoemulsion films. Experimental procedures and preliminary results are described.

  1. Thin-film coatings

    NASA Technical Reports Server (NTRS)

    Buckley, D. H.

    1980-01-01

    Thin, adherent, high density films are discussed with respect to their application in two plasma physics techniques (ion plating and sputtering). The operation of each technique is described as well as what surfaces can be coated, and what kind of materials can be applied. The effects of these films on the mechanical properties of solid surfaces are also discussed.

  2. Literature and Film.

    ERIC Educational Resources Information Center

    Ross, Nigel J.

    1991-01-01

    The teaching of modern literature using film versions of the works studied is examined, and a special course that was organized around this concept is described. Results of the course are discussed, and suggestions are made for how to use film in general literature courses and other contexts. (12 references) (JL)

  3. On Teaching Ethnographic Film

    ERIC Educational Resources Information Center

    Clarfield, Geoffrey

    2013-01-01

    The author of this article, a developmental anthropologist, illustrates how the instructor can use ethnographic films to enhance the study of anthropology and override notions about the scope and efficacy of Western intervention in the Third World, provided the instructor places such films in their proper historical and cultural context. He…

  4. Film and the Humanities.

    ERIC Educational Resources Information Center

    O'Connor, John E., Ed.

    This report on a conference, which brought together representatives of various humanistic disciplines to explore the cross-disciplinary appeal of film study as well as the use of film in stimulating scholarship and teaching, includes a narrative summary of the day's conversations and issues raised, as well as of reprints of articles that suggest…

  5. Elements of Film.

    ERIC Educational Resources Information Center

    Bobker, Lee R.

    A film is the successful combination of two distinct groups of elements: (1) the technical elements by which the film is made (camera, lighting, sound and editing) and (2) the esthetic elements that transform the craft into an art. This book attempts to combine the study of these elements by providing technical information about the process of…

  6. Authors on Film.

    ERIC Educational Resources Information Center

    Geduld, Harry M., Ed.

    Different authors' attitudes toward film are revealed through five different sections of this book: (1) articles, essays, and reviews pertaining to the silent cinema and the transition to sound; (2) general statements on the film medium or filmmakers and their messages; (3) essays dealing with the problems, involvements, and reflections of the…

  7. Thick film hydrogen sensor

    DOEpatents

    Hoffheins, Barbara S.; Lauf, Robert J.

    1995-01-01

    A thick film hydrogen sensor element includes an essentially inert, electrically-insulating substrate having deposited thereon a thick film metallization forming at least two resistors. The metallization is a sintered composition of Pd and a sinterable binder such as glass frit. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors.

  8. Stabilized chromium oxide film

    DOEpatents

    Garwin, Edward L.; Nyaiesh, Ali R.

    1988-01-01

    Stabilized air-oxidized chromium films deposited on high-power klystron ceramic windows and sleeves having a thickness between 20 and 150.ANG. are useful in lowering secondary electron emission yield and in avoiding multipactoring and window failure due to overheating. The ceramic substrate for the film is chosen from alumina, sapphire or beryllium oxide.

  9. Thick film hydrogen sensor

    DOEpatents

    Hoffheins, B.S.; Lauf, R.J.

    1995-09-19

    A thick film hydrogen sensor element includes an essentially inert, electrically-insulating substrate having deposited thereon a thick film metallization forming at least two resistors. The metallization is a sintered composition of Pd and a sinterable binder such as glass frit. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors. 8 figs.

  10. Film Study Hang Ups.

    ERIC Educational Resources Information Center

    Grenier, Charles F.

    1969-01-01

    The interest and delight which students find in film should be preserved from a teacher's excessive zeal to analyze and explain. As the beauty of poetry is frequently diminished through exhaustive analyses of similes, rhyme schemes, and other technical devices, the value of film to high school students can be weakened through too great an emphasis…

  11. Creative Film-Making.

    ERIC Educational Resources Information Center

    Smallman, Kirk

    The fundamentals of motion picture photography are introduced with a physiological explanation for the illusion of motion in a film. Film stock formats and emulsions, camera features, and lights are listed and described. Various techniques of exposure control are illustrated in terms of their effects. Photographing action with a stationary or a…

  12. Film Canister Science

    ERIC Educational Resources Information Center

    Ferstl, Andrew; Schneider, Jamie L.

    2007-01-01

    Opaque film canisters are readily available, cheap, and useful for scientific inquiry in the classroom. They can also be surprisingly versatile and useful as a tool for stimulating scientific inquiry. In this article, the authors describe inquiry activities using film canisters for preservice teachers, including a "black box" activity and several…

  13. Protolytic carbon film technology

    SciTech Connect

    Renschler, C.L.; White, C.A.

    1996-04-01

    This paper presents a technique for the deposition of polyacrylonitrile (PAN) on virtually any surface allowing carbon film formation with only the caveat that the substrate must withstand carbonization temperatures of at least 600 degrees centigrade. The influence of processing conditions upon the structure and properties of the carbonized film is discussed. Electrical conductivity, microstructure, and morphology control are also described.

  14. Filming for Television.

    ERIC Educational Resources Information Center

    Englander, A. Arthur; Petzold, Paul

    Film makers, professional or amateur, will find in this volume an extensive discussion of the adaptation of film technique to television work, of the art of the camera operator, and of the productive relationships between people, organization, and hardware. Chapters include "The Beginnings," an overview of the interrelationship between roles in…

  15. Stabilized chromium oxide film

    DOEpatents

    Nyaiesh, A.R.; Garwin, E.L.

    1986-08-04

    Stabilized air-oxidized chromium films deposited on high-power klystron ceramic windows and sleeves having a thickness between 20 and 150A are useful in lowering secondary electron emission yield and in avoiding multipactoring and window failure due to overheating. The ceramic substrate for the film is chosen from alumina, sapphire or beryllium oxide.

  16. Dental Training Films.

    ERIC Educational Resources Information Center

    Veterans Administration Medical Center, Washington, DC.

    This dental training films catalog is organized into two sections. Section I is a category listing of the films by number and title, indexed according to generalized headings; categories are as follow: anatomy, articulator systems, complete dentures, dental assisting, dental laboratory technology, dental materials, dental office emergencies,…

  17. FAA Film Catalog.

    ERIC Educational Resources Information Center

    Federal Aviation Administration (DOT), Washington, DC.

    Some 75 films from the U.S. Department of Transportation's Federal Aviation Administration are listed in this catalog. Topics dealt with include aerodynamics, airports, aviation history and careers, flying clubs, navigation and weather. Most of the films are 16mm sound and color productions. Filmstrips requiring a 35mm projector and phonograph or…

  18. Abstract Film and Beyond.

    ERIC Educational Resources Information Center

    Le Grice, Malcolm

    A theoretical and historical account of the main preoccupations of makers of abstract films is presented in this book. The book's scope includes discussion of nonrepresentational forms as well as examination of experiments in the manipulation of time in films. The ten chapters discuss the following topics: art and cinematography, the first…

  19. Bursting of soap films

    NASA Astrophysics Data System (ADS)

    Chowdhury, Debashish; Stauffer, Dietrich

    1992-07-01

    Soap films consist of thin films of water in between two monolayers of amphiphilic molecules. Newton black films (NBFs) are the thinnest possible soap films. We have developed a microscopic model of NBFs; this model is a variant of the Widom model for microemulsions. By carrying out Monte Carlo simulations of this model, we have investigated the dependence of the lifetime of the NBFs on (a) the initial concentration of the amphiphilic molecules, (b) the temperature and (c) the bending rigidity of the constituent amphiphilic monolayers. We compare our results with the corresponding experimental observations and suggest further specific experiments. We establish that the “edge energy” of the model bilayer tends to stabilize the NBF; a similar mechanism leads to the well known phenomenon of “self-healing” of small enough holes in pierced vesicles. We also review the laws of growth of holes in soap films during rupture. Finally, we speculate on some other possible applications of our ideas.

  20. Selective inorganic thin films

    SciTech Connect

    Phillips, M.L.F.; Weisenbach, L.A.; Anderson, M.T.

    1995-05-01

    This project is developing inorganic thin films as membranes for gas separation applications, and as discriminating coatings for liquid-phase chemical sensors. Our goal is to synthesize these coatings with tailored porosity and surface chemistry on porous substrates and on acoustic and optical sensors. Molecular sieve films offer the possibility of performing separations involving hydrogen, air, and natural gas constituents at elevated temperatures with very high separation factors. We are focusing on improving permeability and molecular sieve properties of crystalline zeolitic membranes made by hydrothermally reacting layered multicomponent sol-gel films deposited on mesoporous substrates. We also used acoustic plate mode (APM) oscillator and surface plasmon resonance (SPR) sensor elements as substrates for sol-gel films, and have both used these modified sensors to determine physical properties of the films and have determined the sensitivity and selectivity of these sensors to aqueous chemical species.

  1. The National Film Registry: Acquiring Our Film Heritage.

    ERIC Educational Resources Information Center

    Ziegler, Roy A.

    The National Film Registry, which is primarily a designated list of films to be preserved by the Library of Congress, is also a valuable tool for selecting "films that are culturally, historically, and aesthetically significant." Following a brief discussion of the history and selection process of the National Film Registry, Southeast Missouri…

  2. Film Theory and Hugo Munsterberg's "The Film": A Psychological Study.

    ERIC Educational Resources Information Center

    Wicclair, Mark R.

    1978-01-01

    Hugo Munsterberg's "The Film: A Psychological Study" is one of the earliest essays in the area of film theory. Unfortunately, it has remained relatively unknown since its publication in 1916. The author discusses two concepts raised by Munsterberg: the contrast between films in the theatrical mode and films in the cinematic mode. (Author/RK)

  3. Chiral atomically thin films

    NASA Astrophysics Data System (ADS)

    Kim, Cheol-Joo; Sánchez-Castillo, A.; Ziegler, Zack; Ogawa, Yui; Noguez, Cecilia; Park, Jiwoong

    2016-06-01

    Chiral materials possess left- and right-handed counterparts linked by mirror symmetry. These materials are useful for advanced applications in polarization optics, stereochemistry and spintronics. In particular, the realization of spatially uniform chiral films with atomic-scale control of their handedness could provide a powerful means for developing nanodevices with novel chiral properties. However, previous approaches based on natural or grown films, or arrays of fabricated building blocks, could not offer a direct means to program intrinsic chiral properties of the film on the atomic scale. Here, we report a chiral stacking approach, where two-dimensional materials are positioned layer-by-layer with precise control of the interlayer rotation (θ) and polarity, resulting in tunable chiral properties of the final stack. Using this method, we produce left- and right-handed bilayer graphene, that is, a two-atom-thick chiral film. The film displays one of the highest intrinsic ellipticity values (6.5 deg μm–1) ever reported, and a remarkably strong circular dichroism (CD) with the peak energy and sign tuned by θ and polarity. We show that these chiral properties originate from the large in-plane magnetic moment associated with the interlayer optical transition. Furthermore, we show that we can program the chiral properties of atomically thin films layer-by-layer by producing three-layer graphene films with structurally controlled CD spectra.

  4. Chiral atomically thin films

    NASA Astrophysics Data System (ADS)

    Kim, Cheol-Joo; Sánchez-Castillo, A.; Ziegler, Zack; Ogawa, Yui; Noguez, Cecilia; Park, Jiwoong

    2016-06-01

    Chiral materials possess left- and right-handed counterparts linked by mirror symmetry. These materials are useful for advanced applications in polarization optics, stereochemistry and spintronics. In particular, the realization of spatially uniform chiral films with atomic-scale control of their handedness could provide a powerful means for developing nanodevices with novel chiral properties. However, previous approaches based on natural or grown films, or arrays of fabricated building blocks, could not offer a direct means to program intrinsic chiral properties of the film on the atomic scale. Here, we report a chiral stacking approach, where two-dimensional materials are positioned layer-by-layer with precise control of the interlayer rotation (θ) and polarity, resulting in tunable chiral properties of the final stack. Using this method, we produce left- and right-handed bilayer graphene, that is, a two-atom-thick chiral film. The film displays one of the highest intrinsic ellipticity values (6.5 deg μm-1) ever reported, and a remarkably strong circular dichroism (CD) with the peak energy and sign tuned by θ and polarity. We show that these chiral properties originate from the large in-plane magnetic moment associated with the interlayer optical transition. Furthermore, we show that we can program the chiral properties of atomically thin films layer-by-layer by producing three-layer graphene films with structurally controlled CD spectra.

  5. Dependence of film tension on the thickness of smectic films.

    PubMed

    Jaquet, R; Schneider, F

    2003-02-01

    The film tension tau of free standing S(A) films has been measured for films with thicknesses between 2 and 150 layers. There is a clear increase of tau with the thickness for very thin films and a nonlinear slower increase for high thickness. The nonlinearity depends on the amount of liquid crystal accessible to the meniscus of the film during the drawing process. Several models are discussed that describe these effects. PMID:12636700

  6. Discovery in Film, Book Two.

    ERIC Educational Resources Information Center

    Gordon, Malcolm W.

    Approximately 80 16 millimeter (16mm) short films are reviewed in this introduction and guide which attempts to be comprehensive in touching the major areas and styles of 16mm films now being produced. An attempt is made to describe as carefully as possible the style and content of each film and suggest ways in which the films might be used. Films…

  7. Film Scriptwriting: A Practical Manual.

    ERIC Educational Resources Information Center

    Swain, Dwight V.

    Dealing with both documentary and feature films, this book is a guide to using particular tools and procedures in developing ideas and concepts for writing film scripts. Part one deals with the factual, or documentary, film and discusses the proposal outline, film treatment, sequence outline, shooting script, and narration writing. Part two…

  8. The Art of the Film.

    ERIC Educational Resources Information Center

    Lindgren, Ernest

    The author prefaces his consideration of films as an art form with a discussion of the mechanics of filmmaking. He describes the division of talent on a movie set, details the history of the tools of filmmakers, and explains the production and reproduction of a film. The influence of film techniques on plot development in a fiction film is…

  9. Thin film hydrogen sensor

    DOEpatents

    Cheng, Y.T.; Poli, A.A.; Meltser, M.A.

    1999-03-23

    A thin film hydrogen sensor includes a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end. 5 figs.

  10. Negative birefringent polyimide films

    NASA Technical Reports Server (NTRS)

    Harris, Frank W. (Inventor); Cheng, Stephen Z. D. (Inventor)

    1994-01-01

    A negative birefringent film, useful in liquid crystal displays, and a method for controlling the negative birefringence of a polyimide film is disclosed which allows the matching of an application to a targeted amount of birefringence by controlling the degree of in-plane orientation of the polyimide by the selection of functional groups within both the diamine and dianhydride segments of the polyimide which affect the polyimide backbone chain rigidity, linearity, and symmetry. The higher the rigidity, linearity and symmetry of the polyimide backbone, the larger the value of the negative birefringence of the polyimide film.

  11. Thin film hydrogen sensor

    DOEpatents

    Cheng, Yang-Tse; Poli, Andrea A.; Meltser, Mark Alexander

    1999-01-01

    A thin film hydrogen sensor, includes: a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end.

  12. Biomimetic thin film synthesis

    SciTech Connect

    Graff, G.L.; Campbell, A.A.; Gordon, N.R.

    1995-05-01

    The purpose of this program is to develop a new process for forming thin film coatings and to demonstrate that the biomimetic thin film technology developed at PNL is useful for industrial applications. In the biomimetic process, mineral deposition from aqueous solution is controlled by organic functional groups attached to the underlying substrate surface. The coatings process is simple, benign, inexpensive, energy efficient, and particularly suited for temperature sensitive substrate materials (such as polymers). In addition, biomimetic thin films can be deposited uniformly on complex shaped and porous substrates providing a unique capability over more traditional line-of-sight methods.

  13. Amorphous diamond films

    DOEpatents

    Falabella, S.

    1998-06-09

    Amorphous diamond films having a significant reduction in intrinsic stress are prepared by biasing a substrate to be coated and depositing carbon ions thereon under controlled temperature conditions. 1 fig.

  14. Nanostructured thermoplastic polyimide films

    SciTech Connect

    Aglan, Heshmat

    2015-05-19

    Structured films containing multi-walled carbon nanotubes ("MWCNTs") have enhanced mechanical performance in terms of strength, fracture resistance, and creep recovery of polyimide ("PI") films. Preferably, the loadings of MWCNTs can be in the range of 0.1 wt % to 0.5 wt %. The strength of the new PI films dried at 60.degree. C. increased by 55% and 72% for 0.1 wt % MWCNT and 0.5 wt % MWCNT loadings, respectively, while the fracture resistance increased by 23% for the 0.1 wt % MWCNTs and then decreases at a loading of 0.5 wt % MWCNTs. The films can be advantageously be created by managing a corresponding shift in the annealing temperature at which the maximum strength occurs as the MWCNT loadings increase.

  15. Sprites on Film

    NASA Video Gallery

    Filmed at 10,000 frames per second by Japan's NHK television, movies like this of electromagnetic bursts called "sprites" will help scientists better understand how weather high in the atmosphere r...

  16. TAMPERPROOF FILM BADGE

    DOEpatents

    Kocher, L.F.

    1958-10-01

    A persornel dosimeter film badge made of plastic, with provision for a picture of the wearer and an internal slide containing photographic film that is sensitive to various radiations, is described. Four windows made of differing material selectively attenuate alpha, beta, gamma rays, and neutrons so as to distinguish the particular type of radiation the wearer was subjected to. In addition, a lead shield has the identification number of the wearer perforated thereon so as to identify the film after processing. An internal magnetically actuated latch securely locks the slide within the body, and may be withdrawn only upon the external application of two strong magnetic forces in order to insure that the wearer or other curious persons will not accidentally expose the film to visual light.

  17. Magnetron sputtered boron films

    DOEpatents

    Makowiecki, Daniel M.; Jankowski, Alan F.

    1998-01-01

    A method is described for the production of thin boron and titanium/boron films by magnetron sputter deposition. The amorphous boron films contain no morphological growth features, unlike those found when thin films are prepared by various physical vapor deposition processes. Magnetron sputter deposition method requires the use of a high density crystalline boron sputter target which is prepared by hot isostatic pressing. Thin boron films prepared by this method are useful for producing hardened surfaces, surfacing machine tools, etc. and for ultra-thin band pass filters as well as the low Z element in low Z/high Z optical components, such as mirrors which enhance reflectivity from grazing to normal incidence.

  18. Magnetron sputtered boron films

    DOEpatents

    Makowiecki, D.M.; Jankowski, A.F.

    1998-06-16

    A method is described for the production of thin boron and titanium/boron films by magnetron sputter deposition. The amorphous boron films contain no morphological growth features, unlike those found when thin films are prepared by various physical vapor deposition processes. Magnetron sputter deposition method requires the use of a high density crystalline boron sputter target which is prepared by hot isostatic pressing. Thin boron films prepared by this method are useful for producing hardened surfaces, surfacing machine tools, etc. and for ultra-thin band pass filters as well as the low Z element in low Z/high Z optical components, such as mirrors which enhance reflectivity from grazing to normal incidence. 8 figs.

  19. Magnetoresistance of Au films

    DOE PAGESBeta

    Zhang, D. L.; Song, X. H.; Zhang, X.; Zhang, Xiaoguang

    2014-12-10

    Measurement of the magnetoresistance (MR) of Au films as a function of temperature and film thickness reveals a strong dependence on grain size distribution and clear violation of the Kohler s rule. Using a model of random resistor network, we show that this result can be explained if the MR arises entirely from inhomogeneity due to grain boundary scattering and thermal activation of grain boundary atoms.

  20. Multifunctional thin film surface

    DOEpatents

    Brozik, Susan M.; Harper, Jason C.; Polsky, Ronen; Wheeler, David R.; Arango, Dulce C.; Dirk, Shawn M.

    2015-10-13

    A thin film with multiple binding functionality can be prepared on an electrode surface via consecutive electroreduction of two or more aryl-onium salts with different functional groups. This versatile and simple method for forming multifunctional surfaces provides an effective means for immobilization of diverse molecules at close proximities. The multifunctional thin film has applications in bioelectronics, molecular electronics, clinical diagnostics, and chemical and biological sensing.

  1. Polymer film composite transducer

    DOEpatents

    Owen, Thomas E.

    2005-09-20

    A composite piezoelectric transducer, whose piezoeletric element is a "ribbon wound" film of piezolectric material. As the film is excited, it expands and contracts, which results in expansion and contraction of the diameter of the entire ribbon winding. This is accompanied by expansion and contraction of the thickness of the ribbon winding, such that the sound radiating plate may be placed on the side of the winding.

  2. Capacitor film surface assessment studies

    NASA Astrophysics Data System (ADS)

    Galperin, I.; White, W.

    1985-02-01

    In the present investigation of the optical surface of the three widely used, biaxially oriented capacitor films, polypropylene, polyvinylidene fluoride, and polyester, with attention to film surface defects and thickness variation, the defects and their rate of occurrence proved traceable in terms of polymer structure, chemical grouping, and fabrication processing. Film thickness variation was small, yet differed for each film type. Film breakdown voltages have been determined, and alternative causes for the voltage values obtained are proposed. A reciprocal relation is noted between the film breakdown voltage and the dielectric constant.

  3. Epitaxial thin films

    DOEpatents

    Hunt, Andrew Tye; Deshpande, Girish; Lin, Wen-Yi; Jan, Tzyy-Jiuan

    2006-04-25

    Epitatial thin films for use as buffer layers for high temperature superconductors, electrolytes in solid oxide fuel cells (SOFC), gas separation membranes or dielectric material in electronic devices, are disclosed. By using CCVD, CACVD or any other suitable deposition process, epitaxial films having pore-free, ideal grain boundaries, and dense structure can be formed. Several different types of materials are disclosed for use as buffer layers in high temperature superconductors. In addition, the use of epitaxial thin films for electrolytes and electrode formation in SOFCs results in densification for pore-free and ideal gain boundary/interface microstructure. Gas separation membranes for the production of oxygen and hydrogen are also disclosed. These semipermeable membranes are formed by high-quality, dense, gas-tight, pinhole free sub-micro scale layers of mixed-conducting oxides on porous ceramic substrates. Epitaxial thin films as dielectric material in capacitors are also taught herein. Capacitors are utilized according to their capacitance values which are dependent on their physical structure and dielectric permittivity. The epitaxial thin films of the current invention form low-loss dielectric layers with extremely high permittivity. This high permittivity allows for the formation of capacitors that can have their capacitance adjusted by applying a DC bias between their electrodes.

  4. Virus-PEDOT Biocomposite Films

    PubMed Central

    Donavan, Keith C.; Arter, Jessica A.

    2012-01-01

    Virus-poly(3,4-ethylenedioxythiophene) (virus-PEDOT) biocomposite films are prepared by electropolymerizing 3,4-ethylenedioxythiophene (EDOT) in aqueous electrolytes containing 12 mM LiClO4 and the bacteriophage M13. The concentration of virus in these solutions, [virus]soln, is varied from 3 nM to 15 nM. A quartz crystal microbalance is used to directly measure the total mass of the biocomposite film during its electrodeposition. In combination with a measurement of the electrodeposition charge, the mass of the virus incorporated into the film is calculated. These data show that concentration of the M13 within the electropolymerized film, [virus]film, increases linearly with [virus]soln. The incorporation of virus particles into the PEDOT film from solution is efficient, resulting in a concentration ratio: [virus]film:[virus]soln ≈450. Virus incorporation into the PEDOT causes roughening of the film topography that is observed using scanning electron microscopy and atomic force microscopy (AFM). The electrical conductivity of the virus-PEDOT film, measured perpendicular to the plane of the film using conductive tip AFM, decreases linearly with virus loading, from 270 μS/cm for pure PE-DOT films to 50 μS/cm for films containing 100 μM virus. The presence on the virus surface of displayed affinity peptides did not significantly influence the efficiency of incorporation into virus-PEDOT biocomposite films. PMID:22856875

  5. Sensitometric properties of radiographic films and film classification

    NASA Astrophysics Data System (ADS)

    Siidorow, A.

    An attempt was made to elucidate those film characteristics which affect the radiographic image quality and which could be used as the basis of film classification. A literary survey showed that it is apparently impossible to measure the most important film characteristics, i.e., graininess and granularity, in a reliable and simple way. An existing classification method based on a visual comparison of film graininess is recommended.

  6. Filming eugenics: teaching the history of eugenics through film.

    PubMed

    Ooten, Melissa; Trembanis, Sarah

    2007-01-01

    In teaching eugenics to undergraduate students and general public audiences, film should he considered as a provocative and fruitful medium that can generate important discussions about the intersections among eugenics, gender, class, race, and sexuality. This paper considers the use of two films, A Bill of Divorcement and The Lynchburg Story, as pedagogical tools for the history of eugenics. The authors provide background information on the films and suggestions for using the films to foster an active engagement with the historical eugenics movement.

  7. From Written Film History to Visual Film History.

    ERIC Educational Resources Information Center

    Petric, Vladimir

    The poor quality of most university courses in film history is due to several factors, among them the fact that there is insufficient analytical documentation and direct cinematic illustration in existent written film histories. These histories examine films on a thematic level, offering noncinematic interpretation such as literary meaning, social…

  8. Depositing Adherent Ag Films On Ti Films On Alumina

    NASA Technical Reports Server (NTRS)

    Honecy, Frank S.

    1995-01-01

    Report discusses cleaning of ceramic (principally, alumina) substrates in preparation for sputter deposition of titanium intermediate films on substrates followed by sputter deposition of outer silver films. Principal intended application, substrates sliding parts in advanced high-temperature heat engines, and outer silver films serve as solid lubricants: lubricating properties described in "Solid Lubricant for Alumina" (LEW-15495).

  9. Thin films and uses

    DOEpatents

    Baskaran, Suresh; Graff, Gordon L.; Song, Lin

    1998-01-01

    The invention provides a method for synthesizing a titanium oxide-containing film comprising the following steps: (a) preparing an aqueous solution of a titanium chelate with a titanium molarity in the range of 0.01M to 0.6M. (b) immersing a substrate in the prepared solution, (c) decomposing the titanium chelate to deposit a film on the substrate. The titanium chelate maybe decomposed acid, base, temperature or other means. A preferred method provides for the deposit of adherent titanium oxide films from C2 to C5 hydroxy carboxylic acids. In another aspect the invention is a novel article of manufacture having a titanium coating which protects the substrate against ultraviolet damage. In another aspect the invention provides novel semipermeable gas separation membranes, and a method for producing them.

  10. Thin film photovoltaics

    SciTech Connect

    Zweibel, K; Ullal, H S

    1989-05-01

    Thin films are considered a potentially attractive technological approach to making cost-effective electricity by photovoltaics. Over the last twenty years, many have been investigated and some (cadmium telluride, copper indium diselenide, amorphous silicon) have become leading candidates for future large-scale commercialization. This paper surveys the past development of these key thin films and gives their status and future prospects. In all cases, significant progress toward cost-effective PV electricity has been made. If this progress continues, it appears that thin film PV could provide electricity that is competitive for summer daytime peaking power requirements by the middle of the 1990s; and electricity in a range that is competitive with fossil fuel costs (i.e., 6 cents/kilowatt-hour) should be available from PV around the turn of the century. 22 refs., 9 figs.

  11. A multilayer sonic film

    NASA Astrophysics Data System (ADS)

    Munteanu, L.; Chiroiu, V.; Sireteanu, T.; Dumitriu, D.

    2015-10-01

    A non-periodic multilayer film was analyzed to show that, despite its non-periodicity, the film exhibits full band-gaps and localized modes at its interfaces, as well as in the sonic composites. The film consists of alternating layers of two different materials that follow a triadic Cantor sequence. The Cantor structure shows extremely low thresholds for subharmonic generation of ultrasonic waves, compared with homogeneous and periodic structures. The coupling between the extended-mode (phonon) and the localized-mode (fracton) vibration regimes explains the generation of full band-gaps, for which there are no propagating Lamb waves. The large enhancement of the nonlinear interaction results from a more favorable frequency and spatial matching of coupled modes. A full band-gap that excludes Love waves is also analyzed.

  12. Photographic film image enhancement

    NASA Technical Reports Server (NTRS)

    Horner, J. L.

    1975-01-01

    A series of experiments were undertaken to assess the feasibility of defogging color film by the techniques of optical spatial filtering. A coherent optical processor was built using red, blue, and green laser light input and specially designed Fourier transformation lenses. An array of spatial filters was fabricated on black and white emulsion slides using the coherent optical processor. The technique was first applied to laboratory white light fogged film, and the results were successful. However, when the same technique was applied to some original Apollo X radiation fogged color negatives, the results showed no similar restoration. Examples of each experiment are presented and possible reasons for the lack of restoration in the Apollo films are discussed.

  13. Thin film interconnect processes

    NASA Astrophysics Data System (ADS)

    Malik, Farid

    Interconnects and associated photolithography and etching processes play a dominant role in the feature shrinkage of electronic devices. Most interconnects are fabricated by use of thin film processing techniques. Planarization of dielectrics and novel metal deposition methods are the focus of current investigations. Spin-on glass, polyimides, etch-back, bias-sputtered quartz, and plasma-enhanced conformal films are being used to obtain planarized dielectrics over which metal films can be reliably deposited. Recent trends have been towards chemical vapor depositions of metals and refractory metal silicides. Interconnects of the future will be used in conjunction with planarized dielectric layers. Reliability of devices will depend to a large extent on the quality of the interconnects.

  14. Thin film temperature sensor

    NASA Technical Reports Server (NTRS)

    Grant, H. P.; Przybyszewski, J. S.

    1980-01-01

    Thin film surface temperature sensors were developed. The sensors were made of platinum-platinum/10 percent rhodium thermocouples with associated thin film-to-lead wire connections and sputtered on aluminum oxide coated simulated turbine blades for testing. Tests included exposure to vibration, low velocity hydrocarbon hot gas flow to 1250 K, and furnace calibrations. Thermal electromotive force was typically two percent below standard type S thermocouples. Mean time to failure was 42 hours at a hot gas flow temperature of 1250 K and an average of 15 cycles to room temperature. Failures were mainly due to separation of the platinum thin film from the aluminum oxide surface. Several techniques to improve the adhesion of the platinum are discussed.

  15. Alternate film dielectric materials

    SciTech Connect

    Foster, J.C. . Neutron Devices Dept.); Harris, J.O.; Martinez, J.I. )

    1990-01-01

    This paper presents data on polymeric dielectric films evaluated to support the design of high-energy-density capacitors. Evaluated materials include polycarbonate (two sources), polyphenylene sulfide, polyvinylidene fluoride, polyethermide (three sources), polyimide (four sources), polyethersulfone, and polyetherether ketone. A polyester was evaluated as the control material since many of our prior designs utilized this dielectric. The film evaluations were based on dielectric constant and dissipation factor variation as a function of temperature from {minus}55{degree}C to 300{degree}C, as well as dielectric breakdown strength. Additionally, film/foil capacitors in a dry, wrap-and-fill configuration were fabricated and tested to determine insulation resistance, breakdown voltage, and radiation hardness. Results will be presented for all the evaluations based on the several criteria. 7 refs., 4 figs., 4 tabs.

  16. Thin films for material engineering

    NASA Astrophysics Data System (ADS)

    Wasa, Kiyotaka

    2016-07-01

    Thin films are defined as two-dimensional materials formed by condensing one by one atomic/molecular/ionic species of matter in contrast to bulk three-dimensional sintered ceramics. They are grown through atomic collisional chemical reaction on a substrate surface. Thin film growth processes are fascinating for developing innovative exotic materials. On the basis of my long research on sputtering deposition, this paper firstly describes the kinetic energy effect of sputtered adatoms on thin film growth and discusses on a possibility of room-temperature growth of cubic diamond crystallites and the perovskite thin films of binary compound PbTiO3. Secondly, high-performance sputtered ferroelectric thin films with extraordinary excellent crystallinity compatible with MBE deposited thin films are described in relation to a possible application for thin-film MEMS. Finally, the present thin-film technologies are discussed in terms of a future material science and engineering.

  17. The Nuclear Debate in Film

    ERIC Educational Resources Information Center

    Dowling, John

    1977-01-01

    Provides a nuclear film bibliography grouped into the areas of: building and using the bomb; living with the bomb; and living with nuclear power. These films are for mature high school students and older. (MLH)

  18. Holographic analysis of thin films

    NASA Technical Reports Server (NTRS)

    Norden, B. N.; Williams, J. R.

    1970-01-01

    Technique for monitoring deposition of films on surfaces, in place on a real-time basis, reads both the thickness and the uniformity of the deposited film. Holograms are produced from both reflected and transmitted light on one plate.

  19. Foundation for Film and Science

    ERIC Educational Resources Information Center

    van der Veen, G.

    1976-01-01

    Provides a comprehensive discussion on the Stichting Film en Wetenschap, SFW (Foundation for Film and Science), in Utrecht. Various aspects of the use of audio-visual aids in university teaching are looked at in detail. (Editor/RK)

  20. Thin film solar cell workshop

    NASA Technical Reports Server (NTRS)

    Armstrong, Joe; Jeffrey, Frank

    1993-01-01

    A summation of responses to questions posed to the thin-film solar cell workshop and the ensuing discussion is provided. Participants in the workshop included photovoltaic manufacturers (both thin film and crystalline), cell performance investigators, and consumers.

  1. Thin film ceramic thermocouples

    NASA Technical Reports Server (NTRS)

    Gregory, Otto (Inventor); Fralick, Gustave (Inventor); Wrbanek, John (Inventor); You, Tao (Inventor)

    2011-01-01

    A thin film ceramic thermocouple (10) having two ceramic thermocouple (12, 14) that are in contact with each other in at least on point to form a junction, and wherein each element was prepared in a different oxygen/nitrogen/argon plasma. Since each element is prepared under different plasma conditions, they have different electrical conductivity and different charge carrier concentration. The thin film thermocouple (10) can be transparent. A versatile ceramic sensor system having an RTD heat flux sensor can be combined with a thermocouple and a strain sensor to yield a multifunctional ceramic sensor array. The transparent ceramic temperature sensor that could ultimately be used for calibration of optical sensors.

  2. Thin film photovoltaic device

    DOEpatents

    Catalano, Anthony W.; Bhushan, Manjul

    1982-01-01

    A thin film photovoltaic solar cell which utilizes a zinc phosphide semiconductor is of the homojunction type comprising an n-type conductivity region forming an electrical junction with a p-type region, both regions consisting essentially of the same semiconductor material. The n-type region is formed by treating zinc phosphide with an extrinsic dopant such as magnesium. The semiconductor is formed on a multilayer substrate which acts as an opaque contact. Various transparent contacts may be used, including a thin metal film of the same chemical composition as the n-type dopant or conductive oxides or metal grids.

  3. Current Film Periodicals in English. Revised Edition.

    ERIC Educational Resources Information Center

    Reilly, Adam, Comp.

    This bibliography of about 200 periodicals dealing with film covers several types of magazine: scholarly journals on film aesthetics, like "The Film Journal"; news notes for movie fans, like "Film Nut News"; magazines which cover films as well as the other arts, like "Cue" and "After Dark"; film education periodicals, like "Media and Methods";…

  4. Filming in decontamination by mopping

    SciTech Connect

    Rankin, W.N.; Toole, P.A.

    1993-09-28

    Technical assistance was provided High Level Waste Engineering in the investigation and prevention of filming during decontamination by mopping. After mopping operations in a Tank Farm application, a film of the cleaning agent sometimes remained on the surface being cleaned which interfered with monitoring to detect the presence of radioactive material. Scoping tests were conducted to investigate filming characteristics of two cleaning materials. In addition, rinsing test were conducted to demonstrate how filming can be prevented.

  5. NMR characterization of thin films

    DOEpatents

    Gerald II, Rex E.; Klingler, Robert J.; Rathke, Jerome W.; Diaz, Rocio; Vukovic, Lela

    2010-06-15

    A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

  6. NMR characterization of thin films

    DOEpatents

    Gerald, II, Rex E.; Klingler, Robert J.; Rathke, Jerome W.; Diaz, Rocio; Vukovic, Lela

    2008-11-25

    A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

  7. Dual clearance squeeze film damper

    NASA Technical Reports Server (NTRS)

    Fleming, D. P. (Inventor)

    1985-01-01

    A dual clearance hydrodynamic liquid squeeze film damper for a gas turbine engine is described. Under normal operating conditions, the device functions as a conventional squeeze film damper, using only one of its oil films. When an unbalance reaches abusive levels, as may occur with a blade loss or foreign object damage, a second, larger clearance film becomes active, controlling vibration amplitudes in a near optimum manner until the engine can be safely shut down and repaired.

  8. Film Images of the Negro.

    ERIC Educational Resources Information Center

    Manchel, Frank

    1967-01-01

    Educators can help students recognize the value of the motion picture as a social influence by exposing them to film stereotyping and the effect of this distortion on society. A historical study of the film image of the Negro will show him emerging from a humorous, fearful, "perverted" character in early films to "an unfortunate member of society"…

  9. Radical Pedagogy, Prison, and Film

    ERIC Educational Resources Information Center

    O'Neill, Dierdre

    2015-01-01

    This article explores the work of The Inside Film project. Inside Film works with a specific group of people (prisoners and ex-prisoners) in a particular set of circumstances (in prison or on parole) exploring how film making can be used within prison education or with people who have been to prison as a means of fostering a critical engagement…

  10. Longevity Of Dry Film Lubricants

    NASA Technical Reports Server (NTRS)

    Kannel, J. W.; Stockwell, R. D.

    1993-01-01

    Report describes evaluation of dry film lubricants candidate for use in rotary joints of proposed Space Station. Study included experiments and theoretical analyses focused on longevity of sputtered molybdenum disulfide films and ion-plated lead films under conditions partially simulating rolling contact.

  11. Methods for producing complex films, and films produced thereby

    DOEpatents

    Duty, Chad E.; Bennett, Charlee J. C.; Moon, Ji -Won; Phelps, Tommy J.; Blue, Craig A.; Dai, Quanqin; Hu, Michael Z.; Ivanov, Ilia N.; Jellison, Jr., Gerald E.; Love, Lonnie J.; Ott, Ronald D.; Parish, Chad M.; Walker, Steven

    2015-11-24

    A method for producing a film, the method comprising melting a layer of precursor particles on a substrate until at least a portion of the melted particles are planarized and merged to produce the film. The invention is also directed to a method for producing a photovoltaic film, the method comprising depositing particles having a photovoltaic or other property onto a substrate, and affixing the particles to the substrate, wherein the particles may or may not be subsequently melted. Also described herein are films produced by these methods, methods for producing a patterned film on a substrate, and methods for producing a multilayer structure.

  12. Paradoxes in Film Ratings

    ERIC Educational Resources Information Center

    Moore, Thomas L.

    2006-01-01

    The author selected a simple random sample of 100 movies from the "Movie and Video Guide" (1996), by Leonard Maltin. The author's intent was to obtain some basic information on the population of roughly 19,000 movies through a small sample. The "Movie and Video Guide" by Leonard Maltin is an annual ratings guide to movies. While not all films ever…

  13. Film, Radio, and Television.

    ERIC Educational Resources Information Center

    Hardesty, Carolyn, Ed.

    1990-01-01

    This journal issue covers the history of film, radio, and television in Iowa. The first article, "When Pictures and Sound Came to Iowa," summarizes the origin of movies and radio and their early beginnings in Iowa. Using old photographs and measurement charts, the viewing, reading, and listening habits of young people in 1950 and 1958 are…

  14. Films on Deafness.

    ERIC Educational Resources Information Center

    Parlato, Salvatore J., Jr., Comp.

    This filmography on deafness, which contains summaries of 192 16mm films arranged in alphabetical order by title, covers a wide variety of topics as evidenced by the categorical title index: communication, the nature of deafness, detection and measurement of deafness, education and training, multi-handicaps, and noise pollution. Running time, date…

  15. Soap Films and Bubbles.

    ERIC Educational Resources Information Center

    Rice, Karen

    1986-01-01

    Develops and explains a format for a workshop which focuses on soap films and bubbles. The plan consists of: a discussion to uncover what children know about bubbles; explanations of the demonstration equipment; the presentation itself; the assembly of the workshop kit; and time to play with the bubbles. (ML)

  16. Museums With Film Programs.

    ERIC Educational Resources Information Center

    Melton, Hollis, Comp.

    Selectively listed by state are the names and addresses of museums in the U.S., Canada, and Puerto Rico which feature film programs as part of their regular activities. The list, acknowledged to be less than complete, includes some natural history and science museums, some anthropology museums, and state and county historical societies. The…

  17. Rating Films on TV.

    ERIC Educational Resources Information Center

    Herman, Ginette; Leyens, Jacques-Philippe

    1977-01-01

    An analysis of the film viewing habits of Belgian television viewers reveals that movies with advisories regarding sex and violence are watched more than the movies without them. However, movies with qualifications tend to be judged less interesting than movies without qualifications. (JMF)

  18. Films in Depth.

    ERIC Educational Resources Information Center

    Schrievogel, Paul A.; Prete, Anthony T.

    Bound in a slipcover rather than in signatures, this "book" is made up of thirteen separately bound booklets. The first booklet is an introduction to the use of film in the classroom both in teaching the filmic art and in increasing the visual literacy of students on the high school and early college levels. The twelve other booklets each treat a…

  19. Thin film photovoltaic cell

    DOEpatents

    Meakin, John D.; Bragagnolo, Julio

    1982-01-01

    A thin film photovoltaic cell having a transparent electrical contact and an opaque electrical contact with a pair of semiconductors therebetween includes utilizing one of the electrical contacts as a substrate and wherein the inner surface thereof is modified by microroughening while being macro-planar.

  20. Surrealism and Film.

    ERIC Educational Resources Information Center

    Matthews, J. H.

    This book is a critical, genre study of surrealist films including a general discussion of the backgrounds, influences, and overall traits of surrealism as a mode of artistic response to an absurdist world. Citing the impetus of Jacques Vache and Andre Breton as the originators of surrealism, the work expands upon the themes of fractured realism…

  1. Bond percolation in films

    NASA Astrophysics Data System (ADS)

    Korneta, W.; Pytel, Z.

    1988-04-01

    Bond percolation in films with simple cubic structure is considered. It is assumed that the probability of a bond being present between nearest-neighbor sites depends on the distances to surfaces. Based on the relation between the Potts model and the bond percolation model, and using the mean-field approximation, the phase diagram and profiles of the percolation probability have been obtained.

  2. A Film Canister Colorimeter.

    ERIC Educational Resources Information Center

    Gordon, James; James, Alan; Harman, Stephanie; Weiss, Kristen

    2002-01-01

    A low-cost, low-tech colorimeter was constructed from a film canister. The student-constructed colorimeter was used to show the Beer-Lambert relationship between absorbance and concentration and to calculate the value of the molar absorptivity for permanganate at the wavelength emission maximum for an LED. Makes comparisons between this instrument…

  3. Film: The Creative Eye.

    ERIC Educational Resources Information Center

    Sohn, David A.

    Short films are often experimental in nature. They can place aspects of the environment which are usually unnoticed in such a way as to sharpen our observations of the world, and "create a new awareness, a fuller sense of life and being." Based on the premise that visual literacy is becoming increasingly important, this book describes several…

  4. Diamond films: Historical perspective

    SciTech Connect

    Messier, R.

    1993-01-01

    This section is a compilation of notes and published international articles about the development of methods of depositing diamond films. Vapor deposition articles are included from American, Russian, and Japanese publications. The international competition to develop new deposition methodologies is stressed. The current status of chemical vapor deposition of diamond is assessed.

  5. Intercultural Training with Films

    ERIC Educational Resources Information Center

    Roell, Christine

    2010-01-01

    Films are a great medium to use not only to practice English, but also to facilitate intercultural learning. Today English is a global language spoken by people from many countries and cultural backgrounds. Since culture greatly impacts communication, it is helpful for teachers to introduce lessons and activities that reveal how different…

  6. Healing Capillary Films

    NASA Astrophysics Data System (ADS)

    Zheng, Zhong; Fontelos, Marco; Shin, Sangwoo; Stone, Howard

    2015-11-01

    We study the dynamics of a healing viscous thin film driven by surface tension, i.e., the inward spreading of a film to fill a ``hole'' in a thin film. A fourth-order nonlinear partial differential equation is obtained to characterize the time evolution of the film thickness and the novel part of study is then to seek self-similar solutions of the second kind. In this way, we are able to obtain a self-similar solution that describes the interface shape, with the scaling exponent determined by solving a nonlinear eigenvalue problem. The self-similar solution is then compared with the full numerical solution of the partial differential equation, and we observe good agreement. Laboratory experiments have also been conducted using various silicone oils, and the time evolution of the front location and the interface shape can be obtained. A comparison between the theoretical predictions and the experimental observations produces good agreement in both the front location and the interface shape.

  7. Thin film mechanics

    NASA Astrophysics Data System (ADS)

    Cooper, Ryan C.

    This doctoral thesis details the methods of determining mechanical properties of two classes of novel thin films suspended two-dimensional crystals and electron beam irradiated microfilms of polydimethylsiloxane (PDMS). Thin films are used in a variety of surface coatings to alter the opto-electronic properties or increase the wear or corrosion resistance and are ideal for micro- and nanoelectromechanical system fabrication. One of the challenges in fabricating thin films is the introduction of strains which can arise due to application techniques, geometrical conformation, or other spurious conditions. Chapters 2-4 focus on two dimensional materials. This is the intrinsic limit of thin films-being constrained to one atomic or molecular unit of thickness. These materials have mechanical, electrical, and optical properties ideal for micro- and nanoelectromechanical systems with truly novel device functionality. As such, the breadth of applications that can benefit from a treatise on two dimensional film mechanics is reason enough for exploration. This study explores the anomylously high strength of two dimensional materials. Furthermore, this work also aims to bridge four main gaps in the understanding of material science: bridging the gap between ab initio calculations and finite element analysis, bridging the gap between ab initio calculations and experimental results, nanoscale to microscale, and microscale to mesoscale. A nonlinear elasticity model is used to determine the necessary elastic constants to define the strain-energy density function for finite strain. Then, ab initio calculations-density functional theory-is used to calculate the nonlinear elastic response. Chapter 2 focuses on validating this methodology with atomic force microscope nanoindentation on molybdenum disulfide. Chapter 3 explores the convergence criteria of three density functional theory solvers to further verify the numerical calculations. Chapter 4 then uses this model to investigate

  8. Films: 1971/72 Catalog of Films, Film Loops and Filmstrips for Schools, Colleges and Libraries.

    ERIC Educational Resources Information Center

    Learning Corp. of America, New York, NY.

    The films in this catalog are available for sale or rent from Learning Corporation of America. For elementary grades, films are available for use in the language arts and social studies classes. For junior and senior high, college, and adult courses, films are listed for instruction in art, music, and dance; environmental studies; United States…

  9. Thin-film optical initiator

    DOEpatents

    Erickson, Kenneth L.

    2001-01-01

    A thin-film optical initiator having an inert, transparent substrate, a reactive thin film, which can be either an explosive or a pyrotechnic, and a reflective thin film. The resultant thin-film optical initiator system also comprises a fiber-optic cable connected to a low-energy laser source, an output charge, and an initiator housing. The reactive thin film, which may contain very thin embedded layers or be a co-deposit of a light-absorbing material such as carbon, absorbs the incident laser light, is volumetrically heated, and explodes against the output charge, imparting about 5 to 20 times more energy than in the incident laser pulse.

  10. Orientation filtering for crystalline films

    DOEpatents

    Smith, H.I.; Atwater, H.A.; Thompson, C.V.; Geis, M.W.

    1986-12-30

    A substrate is coated with a film to be recrystallized. A pattern of crystallization barriers is created in the film, for example, by etching voids in the film. An encapsulation layer is generally applied to protect the film, fill the voids and otherwise enhance a recrystallization process. Recrystallization is carried out such that certain orientations pass preferentially through the barrier, generally as a result of growth-velocity anisotropy. The result is a film of a specific predetermined crystallographic orientation, a range of orientations or a set of discrete orientations. 7 figs.

  11. Orientation filtering for crystalline films

    DOEpatents

    Smith, Henry I.; Atwater, Harry A.; Thompson, Carl V.; Geis, Michael W.

    1986-12-30

    A substrate is coated with a film to be recrystallized. A pattern of crystallization barriers is created in the film, for example, by etching voids in the film. An encapsulation layer is generally applied to protect the film, fill the voids and otherwise enhance a recrystallization process. Recrystallization is carried out such that certain orientations pass preferentially through the barrier, generally as a result of growth-velocity anisotropy. The result is a film of a specific predetermined crystallographic orientation, a range of orientations or a set of discrete orientations.

  12. [Spectral emissivity of thin films].

    PubMed

    Zhong, D

    2001-02-01

    In this paper, the contribution of multiple reflections in thin film to the spectral emissivity of thin films of low absorption is discussed. The expression of emissivity of thin films derived here is related to the thin film thickness d and the optical constants n(lambda) and k(lambda). It is shown that in the special case d-->infinity the emissivity of thin films is equivalent to that of the bulk material. Realistic numerical and more precise general numerical results for the dependence of the emissivity on d, n(lambda) and k(lambda) are given.

  13. Process to form mesostructured films

    DOEpatents

    Brinker, C. Jeffrey; Anderson, Mark T.; Ganguli, Rahul; Lu, Yunfeng

    1999-01-01

    This invention comprises a method to form a family of supported films film with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts.

  14. Professor Camillo Negro's Neuropathological Films.

    PubMed

    Chiò, Adriano; Gianetto, Claudia; Dagna, Stella

    2016-01-01

    Camillo Negro, Professor in Neurology at the University of Torino, was a pioneer of scientific film. From 1906 to 1908, with the help of his assistant Giuseppe Roasenda and in collaboration with Roberto Omegna, one of the most experienced cinematographers in Italy, he filmed some of his patients for scientific and educational purposes. During the war years, he continued his scientific film project at the Military Hospital in Torino, filming shell-shocked soldiers. In autumn 2011, the Museo Nazionale del Cinema, in partnership with the Faculty of Neurosciences of the University of Torino, presented a new critical edition of the neuropathological films directed by Negro. The Museum's collection also includes 16 mm footage probably filmed in 1930 by Doctor Fedele Negro, Camillo's son. One of these films is devoted to celebrating the effects of the so-called "Bulgarian cure" on Parkinson's disease. PMID:26684422

  15. Thin film superconductor magnetic bearings

    DOEpatents

    Weinberger, Bernard R.

    1995-12-26

    A superconductor magnetic bearing includes a shaft (10) that is subject to a load (L) and rotatable around an axis of rotation, a magnet (12) mounted to the shaft, and a stator (14) in proximity to the shaft. The stator (14) has a superconductor thin film assembly (16) positioned to interact with the magnet (12) to produce a levitation force on the shaft (10) that supports the load (L). The thin film assembly (16) includes at least two superconductor thin films (18) and at least one substrate (20). Each thin film (18) is positioned on a substrate (20) and all the thin films are positioned such that an applied magnetic field from the magnet (12) passes through all the thin films. A similar bearing in which the thin film assembly (16) is mounted on the shaft (10) and the magnet (12) is part of the stator (14) also can be constructed.

  16. Method for making carbon films

    SciTech Connect

    Tan, M.X.

    1999-07-29

    A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area ([approx equal]1000 m[sup 2] /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160 C for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750 C in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750--850 C for between 1--6 hours. 2 figs.

  17. Professor Camillo Negro's Neuropathological Films.

    PubMed

    Chiò, Adriano; Gianetto, Claudia; Dagna, Stella

    2016-01-01

    Camillo Negro, Professor in Neurology at the University of Torino, was a pioneer of scientific film. From 1906 to 1908, with the help of his assistant Giuseppe Roasenda and in collaboration with Roberto Omegna, one of the most experienced cinematographers in Italy, he filmed some of his patients for scientific and educational purposes. During the war years, he continued his scientific film project at the Military Hospital in Torino, filming shell-shocked soldiers. In autumn 2011, the Museo Nazionale del Cinema, in partnership with the Faculty of Neurosciences of the University of Torino, presented a new critical edition of the neuropathological films directed by Negro. The Museum's collection also includes 16 mm footage probably filmed in 1930 by Doctor Fedele Negro, Camillo's son. One of these films is devoted to celebrating the effects of the so-called "Bulgarian cure" on Parkinson's disease.

  18. Method for making carbon films

    DOEpatents

    Tan, Ming X.

    1999-01-01

    A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area (.apprxeq.1000 m.sup.2 /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160.degree. C. for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750.degree. C. in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750-850.degree. C. for between 1-6 hours.

  19. Host thin films incorporating nanoparticles

    NASA Astrophysics Data System (ADS)

    Qureshi, Uzma

    The focus of this research project was the investigation of the functional properties of thin films that incorporate a secondary nanoparticulate phase. In particular to assess if the secondary nanoparticulate material enhanced a functional property of the coating on glass. In order to achieve this, new thin film deposition methods were developed, namely use of nanopowder precursors, an aerosol assisted transport technique and an aerosol into atmospheric pressure chemical vapour deposition system. Aerosol assisted chemical vapour deposition (AACVD) was used to deposit 8 series of thin films on glass. Five different nanoparticles silver, gold, ceria, tungsten oxide and zinc oxide were tested and shown to successfully deposit thin films incorporating nanoparticles within a host matrix. Silver nanoparticles were synthesised and doped within a titania film by AACVD. This improved solar control properties. A unique aerosol assisted chemical vapour deposition (AACVD) into atmospheric pressure chemical vapour deposition (APCVD) system was used to deposit films of Au nanoparticles and thin films of gold nanoparticles incorporated within a host titania matrix. Incorporation of high refractive index contrast metal oxide particles within a host film altered the film colour. The key goal was to test the potential of nanopowder forms and transfer the suspended nanopowder via an aerosol to a substrate in order to deposit a thin film. Discrete tungsten oxide nanoparticles or ceria nanoparticles within a titanium dioxide thin film enhanced the self-cleaning and photo-induced super-hydrophilicity. The nanopowder precursor study was extended by deposition of zinc oxide thin films incorporating Au nanoparticles and also ZnO films deposited from a ZnO nanopowder precursor. Incorporation of Au nanoparticles within a VO: host matrix improved the thermochromic response, optical and colour properties. Composite VC/TiC and Au nanoparticle/V02/Ti02 thin films displayed three useful

  20. "Contact" of nanoscale stiff films.

    PubMed

    Yang, Fut K; Zhang, Wei; Han, Yougun; Yoffe, Serge; Cho, Yungchi; Zhao, Boxin

    2012-06-26

    We investigated the contact behaviors of a nanoscopic stiff thin film bonded to a compliant substrate and derived an analytical solution for determining the elastic modulus of thin films. Microscopic contact deformations of the gold and polydopamine thin films (<200 nm) coated on polydimethylsiloxane elastomers were measured by indenting a soft tip and analyzed in the framework of the classical plate theory and Johnson-Kendall-Roberts (JKR) contact mechanics. The analysis of this thin film contact mechanics focused on the bending and stretching resistance of thin films and is fundamentally different from conventional indentation measurements where the focus is on the fracture and compression of the films. The analytical solution of the elastic modulus of nanoscopic thin films was validated experimentally using 50 and 100 nm gold thin films coated on polydimethylsiloxane elastomers. The technical application of this analysis was further demonstrated by measuring the elastic modulus of thin films of polydopamine, a recently discovered biomimetic universal coating material. Furthermore, the method presented here is able to quantify the contact behaviors of nanoscopic thin films, effectively providing fundamental design parameters, the elastic modulus, and the work of adhesion, crucial for transferring them effectively into practical applications. PMID:22616836

  1. Rupture of vertical soap films

    NASA Astrophysics Data System (ADS)

    Rio, Emmanuelle

    2014-11-01

    Soap films are ephemeral and fragile objects. They tend to thin under gravity, which gives rise to the fascinating variations of colors at their interfaces but leads systematically to rupture. Even a child can create, manipulate and admire soap films and bubbles. Nevertheless, the reason why it suddenly bursts remains a mystery although the soap chosen to stabilize the film as well as the humidity of the air seem very important. One difficulty to study the rupture of vertical soap films is to control the initial solution. To avoid this problem we choose to study the rupture during the generation of the film at a controlled velocity. We have built an experiment, in which we measure the maximum length of the film together with its lifetime. The generation of the film is due to the presence of a gradient of surface concentration of surfactants at the liquid/air interface. This leads to a Marangoni force directed toward the top of the film. The film is expected to burst only when its weight is not balanced anymore by this force. We will show that this leads to the surprising result that the thicker films have shorter lifetimes than the thinner ones. It is thus the ability of the interface to sustain a surface concentration gradient of surfactants which controls its stability.

  2. Biomimetic thin film deposition

    SciTech Connect

    Rieke, P.R.; Graff, G.E.; Campbell, A.A.; Bunker, B.C.; Baskaran, S.; Song, L.; Tarasevich, B.J.; Fryxell, G.E.

    1995-09-01

    Biological mineral deposition for the formation of bone, mollusk shell and other hard tissues provides materials scientists with illustrative materials processing strategies. This presentation will review the key features of biomineralization and how these features can be of technical importance. We have adapted existing knowledge of biomineralization to develop a unique method of depositing inorganic thin films and coating. Our approach to thin film deposition is to modify substrate surfaces to imitate the proteins found in nature that are responsible for controlling mineral deposition. These biomimetic surfaces control the nucleation and growth of the mineral from a supersaturated aqueous solution. This has many processing advantages including simple processing equipment, environmentally benign reagents, uniform coating of highly complex shapes, and enhanced adherence of coating. Many different types of metal oxide, hydroxide, sulfide and phosphate materials with useful mechanical, optical, electronic and biomedical properties can be deposited.

  3. Freely floating smectic films.

    PubMed

    May, Kathrin; Harth, Kirsten; Trittel, Torsten; Stannarius, Ralf

    2014-05-19

    We have investigated the dynamics of freely floating smectic bubbles using high-speed optical imaging. Bubbles in the size range from a few hundred micrometers to several centimeters were prepared from collapsing catenoids. They represent ideal model systems for the study of thin-film fluid dynamics under well-controlled conditions. Owing to the internal smectic layer structure, the bubbles combine features of both soap films and vesicles in their unique shape dynamics. From a strongly elongated initial shape after pinch-off, they relax towards the spherical equilibrium, first by a slow redistribution of the smectic layers, and finally by weak, damped shape oscillations. In addition, we describe the rupture of freely floating smectic bubbles, and the formation and stability of smectic filaments. PMID:24692347

  4. Advanced thin film thermocouples

    NASA Technical Reports Server (NTRS)

    Kreider, K. G.; Semancik, S.; Olson, C.

    1984-01-01

    The fabrication, materials characterization, and performance of thin film platinum rhodium thermocouples on gas turbine alloys was investigated. The materials chosen for the study were the turbine blade alloy systems MAR M200+Hf with NiCoCrAlY and FeCrAlY coatings, and vane alloy systems MAR M509 with FeCrAlY. Research was focussed on making improvements in the problem areas of coating substrate stability, adhesion, and insulation reliability and durability. Diffusion profiles between the substrate and coating with and without barrier coatings of Al2O3 are reported. The relationships between fabrication parameters of thermal oxidation and sputtering of the insulator and its characterization and performance are described. The best thin film thermocouples were fabricated with the NiCoCrAlY coatings which were thermally oxidized and sputter coated with Al2O3.

  5. Magnetoresistance of Au films

    SciTech Connect

    Zhang, D. L. Song, X. H.; Zhang, X.; Zhang, X.-G.

    2014-12-14

    Classical magnetoresistance (MR) in nonmagnetic metals are conventionally understood in terms of the Kohler rule, with violation usually viewed as anomalous electron transport, in particular, as evidence of non-Fermi liquid behavior. Measurement of the MR of Au films as a function of temperature and film thickness reveals a strong dependence on grain size distribution and clear violation of the Kohler rule. Using a model of random resistor network, we show that this result can be explained if the MR arises entirely from inhomogeneity due to grain boundary scattering and thermal activation of grain boundary atoms. Consequently, the Kohler rule should not be used to distinguish normal and anomalous electron transport in solids.

  6. Freely floating smectic films.

    PubMed

    May, Kathrin; Harth, Kirsten; Trittel, Torsten; Stannarius, Ralf

    2014-05-19

    We have investigated the dynamics of freely floating smectic bubbles using high-speed optical imaging. Bubbles in the size range from a few hundred micrometers to several centimeters were prepared from collapsing catenoids. They represent ideal model systems for the study of thin-film fluid dynamics under well-controlled conditions. Owing to the internal smectic layer structure, the bubbles combine features of both soap films and vesicles in their unique shape dynamics. From a strongly elongated initial shape after pinch-off, they relax towards the spherical equilibrium, first by a slow redistribution of the smectic layers, and finally by weak, damped shape oscillations. In addition, we describe the rupture of freely floating smectic bubbles, and the formation and stability of smectic filaments.

  7. Nonlinear optical thin films

    NASA Technical Reports Server (NTRS)

    Leslie, Thomas M.

    1993-01-01

    A focused approach to development and evaluation of organic polymer films for use in optoelectronics is presented. The issues and challenges that are addressed include: (1) material synthesis, purification, and the tailoring of the material properties; (2) deposition of uniform thin films by a variety of methods; (3) characterization of material physical properties (thermal, electrical, optical, and electro-optical); and (4) device fabrication and testing. Photonic materials, devices, and systems were identified as critical technology areas by the Department of Commerce and the Department of Defense. This approach offers strong integration of basic material issues through engineering applications by the development of materials that can be exploited as the active unit in a variety of polymeric thin film devices. Improved materials were developed with unprecedented purity and stability. The absorptive properties can be tailored and controlled to provide significant improvement in propagation losses and nonlinear performance. Furthermore, the materials were incorporated into polymers that are highly compatible with fabrication and patterning processes for integrated optical devices and circuits. By simultaneously addressing the issues of materials development and characterization, keeping device design and fabrication in mind, many obstacles were overcome for implementation of these polymeric materials and devices into systems. We intend to considerably improve the upper use temperature, poling stability, and compatibility with silicon based devices. The principal device application that was targeted is a linear electro-optic modulation etalon. Organic polymers need to be properly designed and coupled with existing integrated circuit technology to create new photonic devices for optical communication, image processing, other laser applications such as harmonic generation, and eventually optical computing. The progression from microscopic sample to a suitable film

  8. [Therapy through film].

    PubMed

    Nicli, Pierrette

    2012-01-01

    For psychiatric patients, playing the role of their life, producing a film, editing it and presenting it to the public with the support of a group made up of patients and caregivers is a real form of self-distancing, a type of therapy. The video group from the Saint Ouen day hospital has been carrying out this creative and therapeutic work for several years. Screenings and exchanges between care centres are regularly organised.

  9. Sound for Film: Audio Education for Filmmakers.

    ERIC Educational Resources Information Center

    Lazar, Wanda

    1998-01-01

    Identifies the specific, unique, and important elements of audio education required by film professionals. Presents a model unit to be included in a film studies program, either as a separate course or as part of a film production or introduction to film course. Offers a model syllabus for such a course or unit on sound in film. (SR)

  10. FOREIGN LANGUAGE FILMS IN LOUISIANA DEPOSITORIES.

    ERIC Educational Resources Information Center

    BABINEAUX, AUDREY

    THIS MANUAL IS AN ANNOTATED LIST OF 16-MILLIMETER EDUCATIONAL FOREIGN LANGUAGE FILMS (BOTH LINGUISTIC AND CULTURAL) WHICH WERE PURCHASED WITH STATE AND FEDERAL FUNDS AND PLACED IN LOUISIANA'S NINE FILM LIBRARIES. FILMS ARE ARRANGED ALPHABETICALLY BY LANGUAGES. FILMS IN THE TARGET LANGUAGE ARE LISTED SEPARATELY FROM FILMS WITH ENGLISH NARRATION. A…

  11. How Reviews Affect Film Interest and Evaluation.

    ERIC Educational Resources Information Center

    Wyatt, Robert O.; Badger, David P.

    A study examined the effects of published film reviews on viewers' interest in and evaluation of the reviewed film. In the film interest experiment, 89 undergraduate students were randomly assigned positive, mixed, or negative reviews of a British film. The control group received a review of a different film. Subjects were asked to read the…

  12. Short Films for Physics Teaching, A Catalog.

    ERIC Educational Resources Information Center

    Bluestone, Barbara Z.; Roth, Richard F.

    This annotated film catalog is a product of the Conference on Single Concept Films in College Physics Teaching sponsored by the Commission on College Physics. Both 8mm and 16mm single concept films are listed for physics and related disciplines. The catalog includes commercial, noncommercial, and foreign films. However, the film coverage was…

  13. 7 CFR 2902.27 - Films.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Films. 2902.27 Section 2902.27 Agriculture... Films. (a) Definition. (1) Products that are used in packaging, wrappings, linings, and other similar applications. (2) Films for which preferred procurement applies are: (i) Semi-durable films. Films that...

  14. Fracture characteristics of balloon films

    NASA Technical Reports Server (NTRS)

    Portanova, Marc A.

    1989-01-01

    An attempt was made to determine the failure modes of high altitude scientific balloons through an investigation of the fracture characteristics of the thin polyethylene films. Two films were the subject of the evaluation, Winzen Int.'s Stratafilm SF-85 and Raven Industries' Astro-E. Research began with an investigation of the film's cold brittleness point and it's effect on the ultimate strength and elasticity of the polyethylene film. A series of preliminary investigations were conducted to develop an understanding of the material characteristics. The primary focus of this investigation was on the notch sensitivity of the films. Simple stress strain tests were also conducted to enable analysis employing fracture toughness parameters. Studies were conducted on both film types at 23 C (room temperature), -60 C, -90 C, and -120 C.

  15. Films on the arms race

    SciTech Connect

    Dowling, J.

    1983-01-01

    Films convey the historical perspectives, the biographical stories, the insights of the participants, and the horror of nuclear war - far better than can any physicist. While films are not very efficient for covering details, derivation, or numbers, they can not be beaten in showing what really happens in a nuclear explosion, in getting across general concepts, in illustrating the parameters of a problem, and the problem itself. Most importantly, films and TV can reach the people who must be informed about these issues if we are to resolve the problems. The author points out how films can contribute to an understanding of the issues of the arms race and nuclear war, with references to specific films. An annotated bibliography of 37 films is then presented.

  16. Polydiacetylene Films Prepared in Microgravity

    NASA Technical Reports Server (NTRS)

    Carswell, William E.; Paley, Mark S.; Frazier, Donald O.; Naumann, Robert J.; Rose, M. Franklin (Technical Monitor)

    2000-01-01

    A diffusive/kinetic rate equation was developed for the growth of polydiacetylene films from solution and compared with a microgravity experiment. The model takes into account both the kinetics of thin film growth and the diffusive transport limitations inherent to microgravity. In order to apply this model, measurements of the density and the ultraviolet extinction coefficient of the films, as well as of the diffusion coefficient of the monomer/solvent system, were made. The thin films grown in microgravity were predicted by the model to grow to a thickness of 0.148 micron, versus 0.150 micron for the ground control films. The flight films grew to 0.102 micron.

  17. Diamond films for laser hardening

    NASA Technical Reports Server (NTRS)

    Albin, S.; Watkins, L.; Ravi, K.; Yokota, S.

    1989-01-01

    Laser-damage experiments were performed on free-standing polycrystalline diamond films prepared by plasma-enhanced CVD. The high laser-induced stress resistance found for this material makes it useful for thin-film coatings for laser optics. Results for diamond-coated silicon substrates demonstrate the enhanced damage threshold imparted by diamond thin-film coatings to materials susceptible to laser damage.

  18. Nanoporous glass films on liquids.

    PubMed

    Zuber, Kamil; Evans, Drew; Murphy, Peter

    2014-01-01

    Glass-like thin films are used in many applications as dielectric layers, barrier coatings, abrasion-resistant films, and/or transparent films. We report the first direct application of such materials to liquid substrates using a plasma-deposition process at atmospheric pressure. The study demonstrates the broader utilization of these materials, for example, as robust membranes for water harvesting or drug delivery.

  19. Polycrystalline thin film photovoltaic technology

    SciTech Connect

    Ullal, H.S.; Zweibel, K.; Mitchell, R.L.; Noufi, R.

    1991-03-01

    Low-cost, high-efficiency thin-film modules are an exciting photovoltaic technology option for generating cost-effective electricity in 1995 and beyond. In this paper we review the significant technical progress made in the following thin films: copper indium diselenide, cadmium telluride, and polycrystalline thin silicon films. Also, the recent US DOE/SERI initiative to commercialize these emerging technologies is discussed. 6 refs., 9 figs.

  20. Frequency mixer having ferromagnetic film

    DOEpatents

    Khitun, Alexander; Roshchin, Igor V.; Galatsis, Kosmas; Bao, Mingqiang; Wang, Kang L.

    2016-03-29

    A frequency conversion device, which may include a radiofrequency (RF) mixer device, includes a substrate and a ferromagnetic film disposed over a surface of the substrate. An insulator is disposed over the ferromagnetic film and at least one microstrip antenna is disposed over the insulator. The ferromagnetic film provides a non-linear response to the frequency conversion device. The frequency conversion device may be used for signal mixing and amplification. The frequency conversion device may also be used in data encryption applications.

  1. Communicating Science: Lessons from Film.

    PubMed

    Berlin, Heather A

    2016-04-01

    Films engage us visually, aurally, viscerally, and emotionally. Incorporating science themes into films has the potential to open up new audiences to scientific ideas, pique their interests, and inspire them to engage in a broader discussion of the science itself. Here, I discuss several narrative techniques and strategies employed in film to effectively engage the audience around science themes, which may be useful tools for scientists looking to become better communicators.

  2. How to Read a Film: The Art, Technology, Language, History and Theory of Film and Media.

    ERIC Educational Resources Information Center

    Monaco, James

    This book discusses film as a narrative technique directly comparable to expression in prose narrative, in painting, and in music; it presents an overview of film as technology, the language of film and television, the history of film in America, Europe, and Asia, and the growth of film criticism. Chapters include "Film As an Art,""Technology:…

  3. Process to form mesostructured films

    DOEpatents

    Brinker, C.J.; Anderson, M.T.; Ganguli, R.; Lu, Y.F.

    1999-01-12

    This invention comprises a method to form a family of supported films with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts. 12 figs.

  4. Evaluation of the Blood Film.

    PubMed

    Campbell, Terry W

    2015-09-01

    Evaluation of hemic cell morphology in stained blood film may be the most important part of the hematologic evaluation of exotic animals. The blood film provides important information regarding red blood cell abnormalities, such as changes in cell shape and color, presence of inclusions, and, in the case of lower vertebrates, changes in the position of the cell nucleus. Stained blood film also provides information about changes in leukocyte numbers and morphology, and shows important hemic features of mammalian platelets and the thrombocytes of lower vertebrates. The blood film is needed in the detection and identification of blood parasites.

  5. Film Review. Films for Use in Professional Courses.

    ERIC Educational Resources Information Center

    Graham, Mike, Ed.

    This book contains a detailed review of over ninety films in the professional preparation of teachers. It is one of eight publications which have been produced by the Science Teacher Education Project. Some of the films have become integral parts of the learning experiences which college and university people have prepared and others are…

  6. The Environment Film Review. A Critical Guide to Ecology Films.

    ERIC Educational Resources Information Center

    Environment Information Center, New York, NY.

    Critical reviews of more than 600 environmental films selected from a field of several thousand are contained in this reference guide. Designed to provide a comprehensive selection of films covering all aspects of environmental affairs, from air pollution to wildlife, the guide is primarily user-oriented. It consists of two parts: a Review…

  7. "Kuleshov on Film": A Spectator-Centered Film Theory.

    ERIC Educational Resources Information Center

    Curran, Trisha

    This paper describes some of the theories of cinematography of Soviet film theorist and filmmaker Lev Kuleshov. It points out that for him, film was communication portraying people's activities emanating from the environment. It explains that he was especially interested in audience response, particularly that of the proletariat, and that he felt…

  8. Protective Film Moves Aside

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Relatively warmer daytime temperatures on Mars have allowed the biobarrier -- a shiny, protective film -- to peel away a little more from the robotic arm of NASA's Phoenix Mars Lander.

    This image shows the spacecraft's robotic arm in its stowed configuration, with the biobarrier unpeeled on landing day, or Sol (Martian day) 0, and the lander's first full day on Mars, Sol 1.

    The 'elbow' of the arm can be seen at the top center of the picture, and the biobarrier is the shiny film seen to the left of the arm.

    The biobarrier is an extra precaution to protect Mars from contamination with any bacteria from Earth. While the whole spacecraft was decontaminated through cleaning, filters and heat, the robotic arm was given additional protection because it is the only spacecraft part that will directly touch the ice below the surface of Mars.

    Before the arm was heated, it was sealed in the biobarrier, which is made of a trademarked film called Tedlar that holds up to baking like a turkey-basting bag. This ensures that any new bacterial spores that might have appeared during the final steps before launch and during the journey to Mars will not contact the robotic arm.

    After Phoenix landed, springs were used to pop back the barrier, giving it room to deploy.

    These images were taken on May 25, 2008 and May 26, 2008 by the spacecraft's Surface Stereo Imager.

    The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  9. Radiation grafting on natural films

    NASA Astrophysics Data System (ADS)

    Lacroix, M.; Khan, R.; Senna, M.; Sharmin, N.; Salmieri, S.; Safrany, A.

    2014-01-01

    Different methods of polymer grafting using gamma irradiation are reported in the present study for the preparation of newly functionalized biodegradable films, and some important properties related to their mechanical and barrier properties are described. Biodegradable films composed of zein and poly(vinyl alcohol) (PVA) were gamma-irradiated in presence of different ratios of acrylic acid (AAc) monomer for compatibilization purpose. Resulting grafted films (zein/PVA-g-AAc) had their puncture strength (PS=37-40 N mm-1) and puncture deformation (PD=6.5-9.8 mm) improved for 30% and 50% PVA in blend, with 5% AAc under 20 kGy. Methylcellulose (MC)-based films were irradiated in the presence of 2-hydroxyethyl methacrylate (HEMA) or silane, in order to determine the effect of monomer grafting on the mechanical properties of films. It was found that grafted films (MC-g-HEMA and MC-g-silane) using 35% monomer performed higher mechanical properties with PS values of 282-296 N mm-1 and PD of 5.0-5.5 mm under 10 kGy. Compatibilized polycaprolactone (PCL)/chitosan composites were developed via grafting silane in chitosan films. Resulting trilayer grafted composite film (PCL/chitosan-g-silane/PCL) presented superior tensile strength (TS=22 MPa) via possible improvement of interfacial adhesion (PCL/chitosan) when using 25% silane under 10 kGy. Finally, MC-based films containing crystalline nanocellulose (CNC) as a filling agent were prepared and irradiated in presence of trimethylolpropane trimethacrylate (TMPTMA) as a grafted plasticizer. Grafted films (MC-g-TMPTMA) presented superior mechanical properties with a TS of 47.9 MPa and a tensile modulus (TM) of 1792 MPa, possibly due to high yield formation of radicals to promote TMPTMA grafting during irradiation. The addition of CNC led to an additional improvement of the barrier properties, with a significant 25% reduction of water vapor permeability (WVP) of grafted films.

  10. Carbonaceous film coating

    DOEpatents

    Maya, L.

    1988-04-27

    A method of making a carbonaceous film comprising heating tris(1,3,2-benzodiazaborolo)borazine or dodecahydro tris(1,3,2)diazaborine(1,2-a:1'2'-c:1''2''-e)borazine in an inert atmosphere in the presence of a substrate to a temperature at which the borazine compound decomposes, and the decomposition products deposit onto the substrate to form a thin, tenacious, highly reflective conductive coating having a narrow band gap which is susceptible of modification and a relatively low coefficient of friction.

  11. Carbonaceous film coating

    DOEpatents

    Maya, Leon

    1989-01-01

    A method of making a carbonaceous film comprising heating tris(1,3,2-benzodiazaborolo)borazine or dodecahydro tris[1,3,2]diazaborine[1,2-a:1'2'-c:1"2"-e]borazine in an inert atmosphere in the presence of a substrate to a temperature at which the borazine compound decomposes, and the decomposition products deposit onto the substrate to form a thin, tenacious, highly reflective conductive coating having a narrow band gap which is susceptible of modification and a relatively low coefficient of friction.

  12. Thin film hydrogen sensor

    DOEpatents

    Lauf, Robert J.; Hoffheins, Barbara S.; Fleming, Pamela H.

    1994-01-01

    A hydrogen sensor element comprises an essentially inert, electrically-insulating substrate having a thin-film metallization deposited thereon which forms at least two resistors on the substrate. The metallization comprises a layer of Pd or a Pd alloy for sensing hydrogen and an underlying intermediate metal layer for providing enhanced adhesion of the metallization to the substrate. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors, and at least one of the resistors is left uncovered. The difference in electrical resistances of the covered resistor and the uncovered resistor is related to hydrogen concentration in a gas to which the sensor element is exposed.

  13. Thin film magnetism

    SciTech Connect

    Bader, S.D. )

    1990-06-01

    New developments in thin-film magnetism are reviewed with an emphasis on the ultrathin regime. The scope includes relatively simple metallic systems in overlayer, sandwich, and superlattice configurations. Sample fabrication, characterization, and magnetic measurement techniques are outlined by highlighting some of the more modern experimental innovations. Current issues and advances that demonstrate the symbiotic relationship between experiment and theory are then examined, including the surface magnetic anisotropy, the two-dimensional critical behavior, the creation of metastable phases via epitaxy, and phenomena associated with coupled magnetic layers. The review ends with a brief account of the impact of the various contemporary developments on the applications area.

  14. Electrical initiation of an energetic nanolaminate film

    DOEpatents

    Tringe, Joseph W.; Gash, Alexander E.; Barbee, Jr., Troy W.

    2010-03-30

    A heating apparatus comprising an energetic nanolaminate film that produces heat when initiated, a power source that provides an electric current, and a control that initiates the energetic nanolaminate film by directing the electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature. Also a method of heating comprising providing an energetic nanolaminate film that produces heat when initiated, and initiating the energetic nanolaminate film by directing an electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature.

  15. Predicting Film Genres with Implicit Ideals

    PubMed Central

    Olney, Andrew McGregor

    2013-01-01

    We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories. PMID:23423823

  16. Liquid film demonstration experiment Skylab SL-4

    NASA Technical Reports Server (NTRS)

    Darbro, W.

    1975-01-01

    The liquid film demonstration experiment performed on Skylab 4 by Astronaut Gerald Carr, which involved the construction of water and soap films by boundary expansion and inertia, is discussed. Results include a 1-ml globule of water expanded into a 7-cm-diameter film as well as complex film structures produced by inertia whose lifetimes are longer in the low-g environment. Also discussed are 1-g acceleration experiments in which the unprovoked rupture of films was photographed and film lifetimes of stationary and rotated soap films were compared. Finally, there is a mathematical discussion regarding minimal surfaces, an isoperimetric problem, and liquid films.

  17. Beryllium thin films for resistor applications

    NASA Technical Reports Server (NTRS)

    Fiet, O.

    1972-01-01

    Beryllium thin films have a protective oxidation resistant property at high temperature and high recrystallization temperature. However, the experimental film has very low temperature coefficient of resistance.

  18. Predicting film genres with implicit ideals.

    PubMed

    Olney, Andrew McGregor

    2012-01-01

    We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories.

  19. Fire resistant films for aircraft applications

    NASA Technical Reports Server (NTRS)

    Kourtides, D. A.

    1983-01-01

    Alternative sandwich panel decorative films were investigated as replacements for the polyvinyl fluoride currently used in aircraft interiors. Candidate films were studied for flammability, smoke emission, toxic gas emission, flame spread, and suitability as a printing surface for the decorative acrylic ink system. Several of the candidate films tested were flame modified polyvinyl fluoride, polyvinylidene fluoride, polyimide, polyamide, polysulfone, polyphenylsulfone, polyethersulfone, polybenzimidazole, polycarbonate, polyparabanic acid, polyphosphazene, polyetheretherketon, and polyester. The films were evaluated as pure films only, films silk-screened with an acrylic ink, and films adhered to a phenolic fiberglass substrate. Films which exhibited the highest fire resistant properties included PEEK polyetheretherketon, Aramid polyamide, and ISO-BPE polyester.

  20. The Uses of Film Extracts.

    ERIC Educational Resources Information Center

    Powell, David

    1967-01-01

    The use of film extracts, either alone or with the whole feature, encourages students to concentrate on a limited number of learning objectives, whereas a full-length film frequently gives rise to confusion and vague generalizations on the part of students. Extracts can be used to illustrate screen language, the style of the director, the history…

  1. Film Study: A Resource Guide.

    ERIC Educational Resources Information Center

    Manchel, Frank

    This resource guide describes six popular approaches to the study of the cinema and provides a practical analysis of selected books, materials, and information about motion picture rentals. Highlighting this extensive survey of film studies are the annotated, critical bibliographies and filmographies of significant books, articles and films by and…

  2. Nonfiction Film; A Critical History.

    ERIC Educational Resources Information Center

    Barsam, Richard Meran

    In this survey history of the documentary or nonfiction cinema, major emphasis is placed upon John Grierson and the British documentary movement as exemplary of the factual films with goals of social improvement and on Robert Flaherty, whose movement stressed poetic or humanistic nonfiction film treatment. Newsreels and current trends in…

  3. Thin film atomic hydrogen detectors

    NASA Technical Reports Server (NTRS)

    Gruber, C. L.

    1977-01-01

    Thin film and bead thermistor atomic surface recombination hydrogen detectors were investigated both experimentally and theoretically. Devices were constructed on a thin Mylar film substrate. Using suitable Wheatstone bridge techniques sensitivities of 80 microvolts/2x10 to the 13th power atoms/sec are attainable with response time constants on the order of 5 seconds.

  4. Teaching the Holocaust through Film.

    ERIC Educational Resources Information Center

    Michalczyk, John J.

    The use of Holocaust-related films and Holocaust survivors as classroom resources is analyzed. The perspective and function of four film genres are outlined as follows. Newsreels, made by the Nazis to chronicle their "progress," provide powerful raw footage of the concentration camp experience. Documentaries, generally made by Allied sources after…

  5. Cinemabilia; Catalogue of Film Literature.

    ERIC Educational Resources Information Center

    Cinemabilia, New York, NY.

    The catalog lists and briefly annotates more than 3,500 current, second-hand, and out-of-print books about film that are available from Cinemabilia, New York City. The catalog is divided into 37 categories. The section on special genre lists works on horror, science fiction, Westerns, and Tarzan films, ranging from "Drums of Fu-Manchu" to "Movie…

  6. Black Male Images in Films

    ERIC Educational Resources Information Center

    Ward, Francis

    1974-01-01

    Argues that the "super" image of the black male in films served three essential purposes: it gave blacks whatever therapy they needed from films; it had hot box office appeal; and it kept white in control of the images blacks have had of themselves. (Author/JM)

  7. Thin films: Past, present, future

    SciTech Connect

    Zweibel, K

    1995-04-01

    This report describes the characteristics of the thin film photovoltaic modules necessary for an acceptable rate of return for rural areas and underdeveloped countries. The topics of the paper include a development of goals of cost and performance for an acceptable PV system, a review of current technologies for meeting these goals, issues and opportunities in thin film technologies.

  8. The Public Library Film Redefined.

    ERIC Educational Resources Information Center

    Peltier, Euclid

    1978-01-01

    An historical discussion of three types of film--teaching, information, and entertainment--is presented. The numbers of films in each category, especially the last, which includes the animated, unnarrated, iconographic, underground, and avant-garde, has grown substantially. Libraries have quickly accepted all except the revolutionary philosophies…

  9. Teaching Film Animation to Children.

    ERIC Educational Resources Information Center

    Andersen, Yvonne

    Under the author's direction, students from 5 to 18 years old have been making prize-winning animated films. In this guide intended for any adult who wishes to teach film animation, she describes and illustrates the techniques she has developed in her seven years of experience teaching animation to children in a workshop setting. All essential…

  10. Symbolism in the Feature Film.

    ERIC Educational Resources Information Center

    Bakony, Edward

    A study of symbolism in feature films reveals how the symbolism employed by film makers can serve as a bridge between feeling and thought, and between aesthetics and cognition. What individuals read from and learn through a symbol varies with what they bring to it. The filmmaker's symbolims must be universal and not private. However, symbolism in…

  11. The Thin Oil Film Equation

    NASA Technical Reports Server (NTRS)

    Brown, James L.; Naughton, Jonathan W.

    1999-01-01

    A thin film of oil on a surface responds primarily to the wall shear stress generated on that surface by a three-dimensional flow. The oil film is also subject to wall pressure gradients, surface tension effects and gravity. The partial differential equation governing the oil film flow is shown to be related to Burgers' equation. Analytical and numerical methods for solving the thin oil film equation are presented. A direct numerical solver is developed where the wall shear stress variation on the surface is known and which solves for the oil film thickness spatial and time variation on the surface. An inverse numerical solver is also developed where the oil film thickness spatial variation over the surface at two discrete times is known and which solves for the wall shear stress variation over the test surface. A One-Time-Level inverse solver is also demonstrated. The inverse numerical solver provides a mathematically rigorous basis for an improved form of a wall shear stress instrument suitable for application to complex three-dimensional flows. To demonstrate the complexity of flows for which these oil film methods are now suitable, extensive examination is accomplished for these analytical and numerical methods as applied to a thin oil film in the vicinity of a three-dimensional saddle of separation.

  12. Thin film ion conducting coating

    DOEpatents

    Goldner, Ronald B.; Haas, Terry; Wong, Kwok-Keung; Seward, George

    1989-01-01

    Durable thin film ion conducting coatings are formed on a transparent glass substrate by the controlled deposition of the mixed oxides of lithium:tantalum or lithium:niobium. The coatings provide durable ion transport sources for thin film solid state storage batteries and electrochromic energy conservation devices.

  13. Metal oxide films on metal

    DOEpatents

    Wu, Xin D.; Tiwari, Prabhat

    1995-01-01

    A structure including a thin film of a conductive alkaline earth metal oxide selected from the group consisting of strontium ruthenium trioxide, calcium ruthenium trioxide, barium ruthenium trioxide, lanthanum-strontium cobalt oxide or mixed alkaline earth ruthenium trioxides thereof upon a thin film of a noble metal such as platinum is provided.

  14. Chitosan in nanostructured thin films.

    PubMed

    Pavinatto, Felippe J; Caseli, Luciano; Oliveira, Osvaldo N

    2010-08-01

    This review paper brings an overview of the use of chitosans in nanostructured films produced with the Langmuir-Blodgett (LB) or the electrostatic layer-by-layer (LbL) techniques, with emphasis on their possible applications. From a survey in the literature one may identify three main types of study with chitosan in nanostructured films. First, the interaction between chitosans and phospholipid Langmuir monolayers has been investigated for probing the mechanisms of chitosan action in their biological applications, with the monolayers serving as cell membrane models. In the second type, chitosan serves as a matrix for immobilization of biomolecules in LB as well as in LbL films, for which chitosan is suitable to help preserve the bioactivity of such biomolecules for long periods of time even in dry, solid films. An important application of these chitosan-containing films is in sensing and biosensing. The third type of study involves exploiting the mechanical and biocompatibility properties of chitosan in producing films with enhanced properties, for example, for tissue engineering. It is emphasized that chitosans have been proven excellent building blocks to produce films with controlled molecular architecture, allowing for synergy between distinct materials. We also discuss the prospects of the field, following a critical review of the latest developments in nanostructured chitosan films. PMID:20590156

  15. Deformation of an asymmetric film

    NASA Astrophysics Data System (ADS)

    Geng, Jun; Selinger, Jonathan

    2010-03-01

    Recent experiments have investigated shape changes of polymer films induced by asymmetric swelling by a chemical vapor. Inspired by recent work on the shaping of elastic sheets by non-Euclidean metrics [1,2], we represent the effect of chemical vapors by a change in the target metric tensor. In this problem, unlike Refs. [1,2], the target metric is asymmetric between the two sides of the film. Changing this metric induces a curvature of the film, which may be Gaussian curvature into a sphere or mean curvature into a cylinder. We calculate the elastic energy for each of these shapes, and show that the sphere is favored for films smaller than a critical size, which depends on the film thickness, while the cylinder is favored for larger films. We compare the formalism for asymmetric films with previous theoretical work on symmetric films, and compare the predictions with experimental results. [4pt] [1] Y. Klein, E. Efrati, and E. Sharon, Science 315, 1116 (2007).[0pt] [2] E. Efrati, E. Sharon, and R. Kupferman, J. Mech. Phys. Solids 57, 762 (2009).

  16. Latino Film and Video Images.

    ERIC Educational Resources Information Center

    Vazquez, Blanca, Ed.

    1990-01-01

    This theme issue of the "Centro Bulletin" examines media stereotypes of Latinos and presents examples of alternatives. "From Assimilation to Annihilation: Puerto Rican Images in U.S. Films" (R. Perez) traces the representation of Puerto Ricans from the early days of television to the films of the 1970s. "The Latino 'Boom' in Hollywood" (C. Fusco)…

  17. Films and the English Class.

    ERIC Educational Resources Information Center

    Donelson, Kenneth, Ed.

    1971-01-01

    The importance of film in the English classroom and its vitality in the English curriculum are discussed. Articles that comprise this issue of the bulletin are: The Trouble with Film Teaching by James E. Cutts; "You Ain't Heard Nothin' Yet" or Send Your Students to the Flicks Tonight by Bob Haskett; It's the Reel Thing: The Verite of Cinema Is…

  18. System for measuring film thickness

    DOEpatents

    Batishko, Charles R.; Kirihara, Leslie J.; Peters, Timothy J.; Rasmussen, Donald E.

    1990-01-01

    A system for determining the thicknesses of thin films of materials exhibiting fluorescence in response to exposure to excitation energy from a suitable source of such energy. A section of film is illuminated with a fixed level of excitation energy from a source such as an argon ion laser emitting blue-green light. The amount of fluorescent light produced by the film over a limited area within the section so illuminated is then measured using a detector such as a photomultiplier tube. Since the amount of fluorescent light produced is a function of the thicknesses of thin films, the thickness of a specific film can be determined by comparing the intensity of fluorescent light produced by this film with the intensity of light produced by similar films of known thicknesses in response to the same amount of excitation energy. The preferred embodiment of the invention uses fiber optic probes in measuring the thicknesses of oil films on the operational components of machinery which are ordinarily obscured from view.

  19. Automatic marker for photographic film

    NASA Technical Reports Server (NTRS)

    Gabbard, N. M.; Surrency, W. M.

    1974-01-01

    Commercially-produced wire-marking machine is modified to title or mark film rolls automatically. Machine is used with film drive mechanism which is powered with variable-speed, 28-volt dc motor. Up to 40 frames per minute can be marked, reducing time and cost of process.

  20. Uses for Free Film Cans

    ERIC Educational Resources Information Center

    Batoff, Mitchell E.; Harmen, Jerry

    1973-01-01

    Describes multiple uses of empty film cans for equipping an elementary school science classroom. Instructional units in which film cans may be useful include buoyancy, mobiles, growing seeds, peas and particles, rocks and minerals, structures, field studies, sound, balancing, electricity, pedulums, chemical change, and optics, light, color. (PS)

  1. Liquid-film electron stripper

    DOEpatents

    Gavin, Basil F.

    1986-01-01

    An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one said of the disc's periphery and with a highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90.degree. angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

  2. Selective inorganic thin films

    SciTech Connect

    Phillips, M.L.F.; Pohl, P.I.; Brinker, C.J.

    1997-04-01

    Separating light gases using membranes is a technology area for which there exists opportunities for significant energy savings. Examples of industrial needs for gas separation include hydrogen recovery, natural gas purification, and dehydration. A membrane capable of separating H{sub 2} from other gases at high temperatures could recover hydrogen from refinery waste streams, and facilitate catalytic dehydrogenation and the water gas shift (CO + H{sub 2}O {yields} H{sub 2} + CO{sub 2}) reaction. Natural gas purification requires separating CH{sub 4} from mixtures with CO{sub 2}, H{sub 2}S, H{sub 2}O, and higher alkanes. A dehydrating membrane would remove water vapor from gas streams in which water is a byproduct or a contaminant, such as refrigeration systems. Molecular sieve films offer the possibility of performing separations involving hydrogen, natural gas constituents, and water vapor at elevated temperatures with very high separation factors. It is in applications such as these that the authors expect inorganic molecular sieve membranes to compete most effectively with current gas separation technologies. Cryogenic separations are very energy intensive. Polymer membranes do not have the thermal stability appropriate for high temperature hydrogen recovery, and tend to swell in the presence of hydrocarbon natural gas constituents. The authors goal is to develop a family of microporous oxide films that offer permeability and selectivity exceeding those of polymer membranes, allowing gas membranes to compete with cryogenic and adsorption technologies for large-scale gas separation applications.

  3. Soap film gas flowmeter

    SciTech Connect

    Lalin, H.S.; Bermudez, J.E.; Fleming, W.T.

    1987-09-08

    A soap film gas flowmeter is described comprising: a flow tube having a hollow body with opposite open ends through which a soap film is propelled and a first closed chamber housing a soap solution. It also includes means for supporting the flow tube in a substantially vertical position with the open bottom end of the flow tube disposed in the first chamber above the soap solution; a second closed chamber into which the open top end of the flow tube extends and gas inlet means for introducing gas into the first chamber at a flow rate to be measured using the flowmeters. A gas exit means is included for discharging the gas introduced into the first chamber through the second chamber. Plus there are means for generating a single soap bubble from the soap solution substantially at the bottom end of the flow tube and a relatively large opening in the flowtube for providing an open passageway for inlet gas to pass through the flowtube when the bottom open end of the flowtube is covered by the soap solution.

  4. Film Fabrication Technologies at NREL

    NASA Technical Reports Server (NTRS)

    Mcconnell, Robert D.

    1993-01-01

    The National Renewable Energy Laboratory (NREL) has extensive capabilities for fabricating a variety of high-technology films. Much of the in-house work in NREL's large photovoltaics (PV) program involves the fabrication of multiple thin-film semiconducting layers constituting a thin-film PV device. NREL's smaller program in superconductivity focuses on the fabrication of superconducting films on long, flexible tape substrates. This paper focuses on four of NREL's in-house research groups and their film fabrication techniques, developed for a variety of elements, alloys, and compounds to be deposited on a variety of substrates. As is the case for many national laboratories, NREL's technology transfer efforts are focusing on Cooperative Research and Development Agreements (CRADA's) between NREL researchers and private industry researchers.

  5. Anode film formation and control

    DOEpatents

    Koski, O.; Marschman, S.C.

    1990-05-01

    A protective film is created about the anode within a cryolite-based electrolyte during electrolytic production of aluminum from alumina. The film functions to minimize corrosion of the anode by the cryolitic electrolyte and thereby extend the life of the anode. Various operating parameters of the electrolytic process are controlled to maintain the protective film about the anode in a protective state throughout the electrolytic reduction of alumina. Such parameters include electrolyte temperature, electrolyte ratio, current density, and Al[sub 2]O[sub 3] concentration. An apparatus is also disclosed to enable identification of the onset of anode corrosion due to disruption of the film to provide real time information regarding the state of the film. 3 figs.

  6. Anode film formation and control

    DOEpatents

    Koski, Oscar; Marschman, Steven C.

    1990-01-01

    A protective film is created about the anode within a cryolite-based electrolyte during electrolytic production of aluminum from alumina. The film function to minimize corrosion of the anode by the cryolitic electrolyte and thereby extend the life of the anode. Various operating parameters of the electrolytic process are controlled to maintain the protective film about the anode in a protective state throughout the electrolytic reduction of alumina. Such parameters include electrolyte temperature, electrolyte ratio, current density, and Al.sub.2 O.sub.3 concentration. An apparatus is also disclosed to enable identification of the onset of anode corrosion due to disruption of the film to provide real time information regarding the state of the film.

  7. A new radiochromic dosimeter film

    NASA Astrophysics Data System (ADS)

    Sidney, L. N.; Lynch, D. C.; Willet, P. S.

    By employing acid-sensitive leuco dyes in a chlorine-containing polymer matrix, a new radiochromic dosimeter film has been developed for gamma, electron beam, and ultraviolet radiation. These dosimeter films undergo a color change from colorless to royal blue, red fuchsia, or black, depending on dye selection, and have been characterized using a visible spectrophotometer over an absorbed dose range of 1 to 100 kGy. The primary features of the film are improved color stability before and after irradiation, whether stored in the dark or under artificial lights, and improved moisture resistance. The effects of absorbed dose, dose rate, and storage conditions on dosimeter performance are discussed. The dosimeter material may be produced as a free film or coated onto a transparent substrate and optionally backed with adhesive. Potential applications for these materials include gamma sterilization indicator films for food and medical products, electron beam dosimeters, and in-line radiation monitors for electron beam and ultraviolet processing.

  8. Stimuli-responsive polymer films.

    PubMed

    Zhai, Lei

    2013-09-01

    Stimuli-responsive polymer films undergo interesting structural and property changes upon external stimuli. Their applications have extended from smart coatings to controlled drug release, smart windows, self-repair and other fields. This tutorial review summarizes non-covalent bonding, reversible reactions and responsive molecules that have played important roles in creating stimuli-responsive systems, and presents the recent development of three types of responsive polymer systems: layer-by-layer polymer multilayer films, polymer brushes, and self-repairing polymer films, with a discussion of their response mechanism. Future research efforts include comprehensive understanding of the response mechanism, producing polymer systems with controlled response properties regarding single or multiple external signals, combining polymer film fabrication with nanotechnology, improving the stability of polymer films on substrates, and evaluating the toxicity of the degradation products. PMID:23749141

  9. Laser damage threshold of diamond films

    NASA Technical Reports Server (NTRS)

    Albin, Sacharia; Cropper, Andre D.; Watkins, Linwood C.; Byvik, Charles E.; Buoncristiani, A. Martin

    1989-01-01

    The possibility that diamond films may inhibit laser-induced damage to optical components in laser systems films was investigated by measuring laser damage thresholds of free-standing diamond film windows, diamond films deposited on silicon substrates, and bare silicon substrate. Polycrystalline diamond films were deposited using a dc plasma-enhanced CVD process. It was found that free-standing diamond films had the highest laser damage threshold at 1064 nm. For a diamond film of 630 nm, the damage threshold was found to be 7 J/sq cm, as compared to a damage threshold of 4.5 J/sq cm for bare silicon, and a low value of 1.5 J/sq cm for the film/substrate combination. The damage mechanism is considered to involve melting or dielectric breakdown induced by laser radiation. The low value of the film/substrate combination is attributed to film stress and conditions of film deposition.

  10. Flow fields in soap films: Relating viscosity and film thickness

    NASA Astrophysics Data System (ADS)

    Prasad, V.; Weeks, Eric R.

    2009-08-01

    We follow the diffusive motion of colloidal particles in soap films with varying h/d , where h is the thickness of the film and d is the diameter of the particles. The hydrodynamics of these films are determined by looking at the correlated motion of pairs of particles as a function of separation R . The Trapeznikov approximation [A. A. Trapeznikov, Proceedings of the 2nd International Congress on Surface Activity (Butterworths, London, 1957), p. 242] is used to model soap films as an effective two-dimensional (2D) fluid in contact with bulk air phases. The flow fields determined from correlated particle motions show excellent agreement with what is expected for the theory of 2D fluids for all our films where 0.6≤h/d≤14.3 , with the 2D shear viscosity matching that predicted by Trapeznikov. However, the parameters of these flow fields change markedly for thick films (h/d>7±3) . Our results indicate that three-dimensional effects become important for these thicker films, despite the flow fields still having a 2D character.

  11. Improving analysis of radiochromic films

    NASA Astrophysics Data System (ADS)

    Baptista Neto, A. T.; Meira-Belo, L. C.; Faria, L. O.

    2014-02-01

    An appropriate radiochromic film should respond uniformly throughout its surface after exposure to a uniform radiation field. The evaluation of radiochromic films may be carried out, for example, by measuring color intensities in film-based digitized images. Fluctuations in color intensity may be caused by many different factors such as optical structure of the film's active layer, defects in structure of the film, scratches and external agents, such as dust. The use of high spatial resolution during film scanning should also increase microscopic uniformity. Since the average is strongly influenced by extreme values, the use of other statistical tools, for which this problem becomes inconspicuous, optimizes the application of higher spatial resolution as well as reduces standard deviations. This paper compares the calibration curves of the XR-QA2 Gafchromic® radiochromic film based on three different methods: the average of all color intensity readings, the median of these same readings and the average of readings that fall between the first and third quartiles. Results indicate that a higher spatial resolution may be adopted whenever the calibration curve is based on tools less influenced by extreme values such as those generated by the factors mentioned above.

  12. Polyimide Aerogel Thin Films

    NASA Technical Reports Server (NTRS)

    Meador, Mary Ann; Guo, Haiquan

    2012-01-01

    Polyimide aerogels have been crosslinked through multifunctional amines. This invention builds on "Polyimide Aerogels With Three-Dimensional Cross-Linked Structure," and may be considered as a continuation of that invention, which results in a polyimide aerogel with a flexible, formable form. Gels formed from polyamic acid solutions, end-capped with anhydrides, and cross-linked with the multifunctional amines, are chemically imidized and dried using supercritical CO2 extraction to give aerogels having density around 0.1 to 0.3 g/cubic cm. The aerogels are 80 to 95% porous, and have high surface areas (200 to 600 sq m/g) and low thermal conductivity (as low as 14 mW/m-K at room temperature). Notably, the cross-linked polyimide aerogels have higher modulus than polymer-reinforced silica aerogels of similar density, and can be fabricated as both monoliths and thin films.

  13. Digital film library implementation

    NASA Astrophysics Data System (ADS)

    Kishore, Sheel; Khalsa, Satjeet S.; Seshadri, Sridhar B.; Arenson, Ronald L.

    1991-07-01

    The Radiology Department at the University of Pennsylvania is in the process of clinically testing its PACS implementation. The PACS implementation has been built around a Vortech Image Archival and Retrieval System (IARS) with a 140-platter optical jukebox. The Vortech IARS provides archival services only. A set of software modules have been developed in-house that allow the system to function as a digital film library. The current implementation allows connectivity to a RIS (DECrad), supports the routing of images to two intensive care units, and allows image acquisition from a Du Pont FD2000 laser scanner and two GE SIGNA MR units. All process-to-process communication follows the ACR/NEMA 2.0 protocol. The proposed folder extensions to ACR/NEMA 2.0 are being utilized for sending information to the display nodes. The system has been running clinically for about three months. Details of the design, implementation, and functionality of the PACS are presented.

  14. Ferromagnetic thin films

    DOEpatents

    Krishnan, Kannan M.

    1994-01-01

    A ferromagnetic .delta.-Mn.sub.1-x Ga.sub.x thin film having perpendicular anisotropy is described which comprises: (a) a GaAs substrate, (b) a layer of undoped GaAs overlying said substrate and bonded thereto having a thickness ranging from about 50 to about 100 nanometers, (c) a layer of .delta.-Mn.sub.1-x Ga.sub.x overlying said layer of undoped GaAs and bonded thereto having a thickness ranging from about 20 to about 30 nanometers, and (d) a layer of GaAs overlying said layer of .delta.-Mn.sub.1-x Ga.sub.x and bonded thereto having a thickness ranging from about 2 to about 5 nanometers, wherein x is 0.4 .+-.0.05.

  15. Ferromagnetic thin films

    DOEpatents

    Krishnan, K.M.

    1994-12-20

    A ferromagnetic [delta]-Mn[sub 1[minus]x]Ga[sub x] thin film having perpendicular anisotropy is described which comprises: (a) a GaAs substrate, (b) a layer of undoped GaAs overlying said substrate and bonded thereto having a thickness ranging from about 50 to about 100 nanometers, (c) a layer of [delta]-Mn[sub 1[minus]x]Ga[sub x] overlying said layer of undoped GaAs and bonded thereto having a thickness ranging from about 20 to about 30 nanometers, and (d) a layer of GaAs overlying said layer of [delta]-Mn[sub 1[minus]x]Ga[sub x] and bonded thereto having a thickness ranging from about 2 to about 5 nanometers, wherein x is 0.4[+-]0.05. 7 figures.

  16. Thin film hydrogen sensor

    DOEpatents

    Lauf, R.J.; Hoffheins, B.S.; Fleming, P.H.

    1994-11-22

    A hydrogen sensor element comprises an essentially inert, electrically-insulating substrate having a thin-film metallization deposited thereon which forms at least two resistors on the substrate. The metallization comprises a layer of Pd or a Pd alloy for sensing hydrogen and an underlying intermediate metal layer for providing enhanced adhesion of the metallization to the substrate. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors, and at least one of the resistors is left uncovered. The difference in electrical resistances of the covered resistor and the uncovered resistor is related to hydrogen concentration in a gas to which the sensor element is exposed. 6 figs.

  17. Antimicrobial edible films and coatings.

    PubMed

    Cagri, Arzu; Ustunol, Zeynep; Ryser, Elliot T

    2004-04-01

    Increasing consumer demand for microbiologically safer foods, greater convenience, smaller packages, and longer product shelf life is forcing the industry to develop new food-processing, cooking, handling, and packaging strategies. Nonfluid ready-to-eat foods are frequently exposed to postprocess surface contamination, leading to a reduction in shelf life. The food industry has at its disposal a wide range of nonedible polypropylene- and polyethylene-based packaging materials and various biodegradable protein- and polysaccharide-based edible films that can potentially serve as packaging materials. Research on the use of edible films as packaging materials continues because of the potential for these films to enhance food quality, food safety, and product shelf life. Besides acting as a barrier against mass diffusion (moisture, gases, and volatiles), edible films can serve as carriers for a wide range of food additives, including flavoring agents, antioxidants, vitamins, and colorants. When antimicrobial agents such as benzoic acid, sorbic acid, propionic acid, lactic acid, nisin, and lysozyme have been incorporated into edible films, such films retarded surface growth of bacteria, yeasts, and molds on a wide range of products, including meats and cheeses. Various antimicrobial edible films have been developed to minimize growth of spoilage and pathogenic microorganisms, including Listeria monocytogenes, which may contaminate the surface of cooked ready-to-eat foods after processing. Here, we review the various types of protein-based (wheat gluten, collagen, corn zein, soy, casein, and whey protein), polysaccharide-based (cellulose, chitosan, alginate, starch, pectin, and dextrin), and lipid-based (waxes, acylglycerols, and fatty acids) edible films and a wide range of antimicrobial agents that have been or could potentially be incorporated into such films during manufacture to enhance the safety and shelf life of ready-to-eat foods.

  18. America on Film: A Humanities Composition Course.

    ERIC Educational Resources Information Center

    Recchia, Edward

    This paper argues that film courses are useful because they sensitize students both to the artistic qualities of film expression and to equivalent qualities in other forms of expression. The objectives of a film course at Michigan State University are: to develop the students' knowledge of the film medium and through that knowledge develop a…

  19. "Space slitter" for film or tape

    NASA Technical Reports Server (NTRS)

    Johnson, W. H.

    1978-01-01

    Device cuts film or tape into strips by guiding film in channel under cutting blades. Device is operated by lifting pressure bar to insert blades into film. Film is then pulled through blades. Cutter has potential uses in advertising, commercial art, and publishing fields.

  20. The Celluloid Literature: Film in the Humanities.

    ERIC Educational Resources Information Center

    Jinks, William

    The purposes of this book are to introduce film as an art and to show how close, both in form and content, literature and the narrative film are to one another. To accomplish these purposes, the basic components of literature and film are compared, including language (the novel uses words, while the film uses images), point of view, and figurative…

  1. Modified intraoral film holders for postmortem identification.

    PubMed

    Oeschger, M P; Hubar, J S

    1999-07-01

    To date there have not been any commercial dental X-ray film holders marketed to accommodate the special needs of forensic odontologists. Modification of standard Rinn XCP film holders by the investigators produced self-supporting film holders that do not require the active participation from the examinee. The modified film holders greatly simplify the operator's technique of exposing dental radiographs on cadavers.

  2. Historical Films in the Latin Classroom.

    ERIC Educational Resources Information Center

    Buller, Jeffrey L.

    Guidelines and lesson plans are presented for teachers of Latin using historical films as instructional and support materials. A discussion of the use of historical films addresses these issues in classroom practice: the legality of using films in the classroom (copyrights); techniques for using historical films as sources of cultural information;…

  3. Morphology of Microscopic Thin Rubber Films

    NASA Astrophysics Data System (ADS)

    Zhang, Xin; Briber, Robert; Wang, Howard

    2014-03-01

    Microscopic thin rubber films have been prepared using photolithographic methods. Thin films of low molecular weight polybutadiene have been spun cast on positive photoresists, and transferred to various substrates upon UV exposure for crosslinking and defining the lateral dimension. The morphological scaling of thin rubber films as a function of film dimension and temperature is discussed.

  4. Lifelong Learning Films; 1972-1973.

    ERIC Educational Resources Information Center

    California Univ., Berkeley. Media Extension Center.

    Over 450 newly acquired films are described in this brochure. They are, for the most part, short black-and-white 16 mm films produced by the University of California Extension Media Center and selected films from other producers. The main entry section arranges the films alphabetically by title; it gives an annotation, the running time,…

  5. FILM WORKSHOP SUCCESSFUL WITH TSU STUDENTS.

    ERIC Educational Resources Information Center

    BAHRENBERG, JIM

    AN UPWARD BOUND FILM WORKSHOP AT TEXAS SOUTHERN UNIVERSITY EXPOSED STUDENTS TO FILMS AS A CREATIVE ART FORM, A MEANS OF COMMUNICATION, AND A BASIS FOR DISCUSSING VALUES. IN ADDITION TO VIEWING SEVERAL SHORT, PROFESSIONALLY-DEVELOPED FILMS, STUDENTS WROTE AND PRODUCED TWO OF THEIR OWN. ONE STUDENT-PRODUCED FILM--A LIGHT SHOW--ILLUMINATED THE UNITY…

  6. Olympic Training Film Profiles. Volume Four.

    ERIC Educational Resources Information Center

    1972

    Providing a convenient reference source to training and educational films, this fourth volume of the "Training Film Profiles" lists films and filmstrips from all sources for 1971 through 1972. The volume first presents an index, listing film titles and categories from the first four volumes, and then provides entries arranged according to subject…

  7. Instructional Film Research and the Learner.

    ERIC Educational Resources Information Center

    Bowie, Melvin McKinney

    A brief discussion of three phases in research on instructional films--whether films can teach (approximately 1910-1950), how films teach (1940 through the late 1950s), and who learns from films (1960-1985)--introduces a review of the research literature on the third phase. The experimental studies reviewed focus on three concerns: (1) use of…

  8. 19 CFR 12.41 - Prohibited films.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 1 2013-04-01 2013-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any...

  9. 19 CFR 12.41 - Prohibited films.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 1 2012-04-01 2012-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any...

  10. 19 CFR 12.41 - Prohibited films.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 1 2014-04-01 2014-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any...

  11. 16 CFR 501.1 - Camera film.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 1 2012-01-01 2012-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk...

  12. 16 CFR 501.1 - Camera film.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk...

  13. 16 CFR 501.1 - Camera film.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 1 2013-01-01 2013-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk...

  14. Subjective Sexual Arousal to Films of Masturbation

    ERIC Educational Resources Information Center

    Mosher, Donald L.; Abramson, Paul R.

    1977-01-01

    A film of a male or female masturbating was viewed by 96 males and 102 females. Males reported the highest level of sexual arousal to the female film and the lowest level of arousal to the male film. Females were sexually aroused by both films. (Author)

  15. A 3M high temperature dielectric film

    NASA Technical Reports Server (NTRS)

    Hampl, Edward, Jr.

    1994-01-01

    The performance characteristics of a dielectric film are summarized. Additionally, the film's environmental and chemical properties are listed: low shrinkage to 300 C; moisture insensitive; low outgassing under vacuum; excellent surface qualities--easy metallization of film; flame retardant; and low smoke generation. A series of graphs that display the performance characteristics of the film are also presented.

  16. Using Popular Children's Films in Science

    ERIC Educational Resources Information Center

    Wadsworth, Elle; Croker, Stev; Harrison, Tim

    2012-01-01

    Watching films is a common activity for children outside of school, and incorporating popular films that contain scientific references has the potential to spark interest in the classroom. Clips rather than entire films can be used, as the children will maintain focus on the lesson objectives while being excited by the appeal of the film. The use…

  17. 19 CFR 12.41 - Prohibited films.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any...

  18. 16 CFR 501.1 - Camera film.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the...

  19. Geoflicks Reviewed--Films about Hawaiian Volcanoes.

    ERIC Educational Resources Information Center

    Bykerk-Kauffman, Ann

    1994-01-01

    Reviews 11 films on volcanic eruptions in the United States. Films are given a one- to five-star rating and the film's year, length, source and price are listed. Top films include "Inside Hawaiian Volcanoes" and "Kilauea: Close up of an Active Volcano." (AIM)

  20. Cultural Dependency in Canada's Feature Film Industry.

    ERIC Educational Resources Information Center

    Pendakur, Manjunath

    1981-01-01

    Examines the ownership and policies of the dominant firms in the Canadian film market to explain Canada's dependence on imported films. Demonstrates how the economic relations existing between Canadian and U.S. film industries limit the profitability of films made in Canada. (JMF)

  1. 16 CFR 501.1 - Camera film.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 1 2011-01-01 2011-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk...

  2. 19 CFR 12.41 - Prohibited films.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 1 2011-04-01 2011-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any...

  3. American Film Genres: Approaches to a Critical Theory of Popular Film.

    ERIC Educational Resources Information Center

    Kaminsky, Stuart M.

    This book is divided into twelve sections and contains photographs from many of the films discussed. The introduction defines film genre and describes the general theories behind this book; "The Individual Film" analyzes the film "Little Caesar" as it relates to the genre of gangster films; "Comparative Forms" describes the similarities and…

  4. Liquid-film electron stripper

    DOEpatents

    Leemann, Beat T.; Yourd, Roland B.

    1984-01-01

    A thin freestanding oil film is produced in vacuum by directing an oil stream radially inward to the hollow-ground sharp outer edge of a rotating disc. The sides of the edge are roughened somewhat to aid in dispersing oil from the disc. Oil is removed from the surface of disc to prevent formation of oil droplets which might spin off the disc and disrupt the oil film. An ion beam is directed through the thin oil film so that electrons are stripped from the ions to increase their charge.

  5. Liquid-film electron stripper

    DOEpatents

    Leemann, B.T.; Yourd, R.B.

    1982-03-09

    A thin freestanding oil film is produced in vacuum by directing an oil stream radially inward to the hollow-ground sharp outer edge of a rotating disc. The sides of the edge are roughened somewhat to aid in dispersing oil from the disc. Oil is removed from the surface of disc to prevent formation of oil droplets which might spin off the disc and disrupt the oil film. An ion beam is directed through the thin oil film so that electrons are stripped from the ions to increase their charge.

  6. Film boiling of mercury droplets

    NASA Technical Reports Server (NTRS)

    Baumeister, K. J.; Schoessow, G. J.; Chmielewski, C. E.

    1975-01-01

    Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. Diffusion from the upper surface of the drop appears as a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

  7. Tailoring nanocrystalline diamond film properties

    DOEpatents

    Gruen, Dieter M.; McCauley, Thomas G.; Zhou, Dan; Krauss, Alan R.

    2003-07-15

    A method for controlling the crystallite size and growth rate of plasma-deposited diamond films. A plasma is established at a pressure in excess of about 55 Torr with controlled concentrations of hydrogen up to about 98% by volume, of unsubstituted hydrocarbons up to about 3% by volume and an inert gas of one or more of the noble gases and nitrogen up to about 98% by volume. The volume ratio of inert gas to hydrogen is preferably maintained at greater than about 4, to deposit a diamond film on a suitable substrate. The diamond film is deposited with a predetermined crystallite size and at a predetermined growth rate.

  8. Film boiling of mercury droplets

    NASA Technical Reports Server (NTRS)

    Baumeister, K. J.; Schoessow, G. J.; Chmielewski, C. E.

    1975-01-01

    Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. For these data, diffusion from the upper surface of the drop is a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

  9. Surface wrinkling on polydopamine film

    NASA Astrophysics Data System (ADS)

    Meng, Jieyun; Xie, Jixun; Han, Xue; Lu, Conghua

    2016-05-01

    In this paper, we report a non-lithographic strategy to realize surface patterns on polydopamine films. It is based on surface wrinkling, which is induced on polydopamine (PDA) films that are grown on uniaxially pre-strained polydimethylsiloxane (PDMS) substrates through self-polymerization of dopamine, followed by the pre-strain release. We investigate the influences of the experimental conditions including polymerization time, prestrain and the dopamine solution concentration on the wrinkling patterns. Furthermore, we take advantage of the reducibility of PDA to fabricate silver nanoparticle-deposited PDA films with surface-wrinkled patterns, which may have potential applications in the related fields.

  10. Vapor deposition of thin films

    DOEpatents

    Smith, David C.; Pattillo, Stevan G.; Laia, Jr., Joseph R.; Sattelberger, Alfred P.

    1992-01-01

    A highly pure thin metal film having a nanocrystalline structure and a process of preparing such highly pure thin metal films of, e.g., rhodium, iridium, molybdenum, tungsten, rhenium, platinum, or palladium by plasma assisted chemical vapor deposition of, e.g., rhodium(allyl).sub.3, iridium(allyl).sub.3, molybdenum(allyl).sub.4, tungsten(allyl).sub.4, rhenium(allyl).sub.4, platinum(allyl).sub.2, or palladium(allyl).sub.2 are disclosed. Additionally, a general process of reducing the carbon content of a metallic film prepared from one or more organometallic precursor compounds by plasma assisted chemical vapor deposition is disclosed.

  11. Importance of combining convection with film cooling

    NASA Technical Reports Server (NTRS)

    Colladay, R. S.

    1971-01-01

    The interaction of film and convection cooling and its effect on wall cooling efficiency is investigated analytically for two cooling schemes for advanced gas turbine applications. The two schemes are full coverage- and counterflow-film cooling. In full coverage film cooling, the cooling air issues from a large number of small discrete holes in the surface. Counterflow film cooling is a film-convection scheme with film injection from a slot geometry. The results indicate that it is beneficial to utilize as much of the cooling air heat sink as possible for convection cooling prior to ejecting it as a film.

  12. Polyvinylpyrrolidone oral films of enrofloxacin: film characterization and drug release.

    PubMed

    Kumar, G Prem; Phani, A R; Prasad, R G S V; Sanganal, Jagadeesh S; Manali, N; Gupta, R; Rashmi, N; Prabhakara, G S; Salins, C Paul; Sandeep, K; Raju, D B

    2014-08-25

    Enrofloxacin is a fluoroquinolone derivative used for treating urinary tract, respiratory and skin infections in animals. However, low solubility and low bioavailability prevented it from using on humans. Polyvinylpyrrolidone (PVP) is an inert, non toxic polymer with excellent hydrophilic properties, besides it can enhance bioavailability by forming drug polymer conjugates. With the aim of increasing solubility and bioavailability, enrofloxacin thin films were prepared using PVP as a polymer matrix. The obtained oral thin films exhibited excellent uniformity and mechanical properties. Swelling properties of the oral thin films revealed that the water uptake was enhanced by 21%. The surface pH has been found to be 6.8±0.1 indicating that these films will not cause any irritation to oral mucosa. FTIR data of the oral thin films indicated physical interaction between drug and polymer. SEM analysis revealed uniform distribution of drug in polymer matrix. In vitro drug release profiles showed enhanced release profiles (which are also pH dependant) for thin films compared to pure drug. Antibacterial activity was found to be dose dependent and maximum susceptibility was found on Klebsiella pneumonia making this preparation more suitable for respiratory infections.

  13. Thin film cell development workshop report

    NASA Technical Reports Server (NTRS)

    Woodyard, James R.

    1991-01-01

    The Thin Film Development Workshop provided an opportunity for those interested in space applications of thin film cells to debate several topics. The unique characteristics of thin film cells as well as a number of other issues were covered during the discussions. The potential of thin film cells, key research and development issues, manufacturing issues, radiation damage, substrates, and space qualification of thin film cells were discussed.

  14. Cellulose triacetate, thin film dielectric capacitor

    NASA Technical Reports Server (NTRS)

    Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

    1993-01-01

    Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

  15. Cellulose triacetate, thin film dielectric capacitor

    NASA Technical Reports Server (NTRS)

    Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

    1995-01-01

    Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

  16. The Art of Teaching Social Studies with Film

    ERIC Educational Resources Information Center

    Russell, William B., III

    2012-01-01

    Teaching with film is a powerful and meaningful instructional strategy. This article discusses five classroom-tested methods for teaching with film: (1) film as a visual textbook, (2) film as a depicter of atmosphere, (3) film as an analogy, (4) film as a historiography, and (5) film as a springboard. Each of the methods discussed includes…

  17. Manganite films: Tuning phase diagrams

    NASA Astrophysics Data System (ADS)

    Mihailovic, Dragan

    2016-09-01

    Strain engineering can tune a manganite film into an antiferromagnetic insulating state whose extreme photo-susceptibility allows for the ordinary ferromagnetic metal state to then be transiently realized.

  18. Thermal diffusivity of diamond films

    NASA Technical Reports Server (NTRS)

    Albin, Sacharia; Winfree, William P.; Crews, B. Scott

    1990-01-01

    A laser pulse technique to measure the thermal diffusivity of diamond films deposited on a silicon substrate is developed. The effective thermal diffusivity of diamond film on silicon was measured by observing the phase and amplitude of the cyclic thermal waves generated by the laser pulses. An analytical model is developed to calculate the effective in-plane (face-parallel) diffusivity of a two layer system. The model is used to reduce the effective thermal diffusivity of the diamond/silicon sample to a value for the thermal diffusivity and conductivity of the diamond film. Phase and amplitude measurements give similar results. The thermal conductivity of the films is found to be better than that of type 1a natural diamond.

  19. Fabrication of amorphous diamond films

    DOEpatents

    Falabella, S.

    1995-12-12

    Amorphous diamond films having a significant reduction in intrinsic stress are prepared by biasing a substrate to be coated and depositing carbon ions thereon under controlled temperature conditions. 1 fig.

  20. Applications of film thickness equations

    NASA Technical Reports Server (NTRS)

    Hamrock, B. J.; Dowson, D.

    1983-01-01

    A number of applications of elastohydrodynamic film thickness expressions were considered. The motion of a steel ball over steel surfaces presenting varying degrees of conformity was examined. The equation for minimum film thickness in elliptical conjunctions under elastohydrodynamic conditions was applied to roller and ball bearings. An involute gear was also introduced, it was again found that the elliptical conjunction expression yielded a conservative estimate of the minimum film thickness. Continuously variable-speed drives like the Perbury gear, which present truly elliptical elastohydrodynamic conjunctions, are favored increasingly in mobile and static machinery. A representative elastohydrodynamic condition for this class of machinery is considered for power transmission equipment. The possibility of elastohydrodynamic films of water or oil forming between locomotive wheels and rails is examined. The important subject of traction on the railways is attracting considerable attention in various countries at the present time. The final example of a synovial joint introduced the equation developed for isoviscous-elastic regimes of lubrication.

  1. Process for forming planarized films

    DOEpatents

    Pang, Stella W.; Horn, Mark W.

    1991-01-01

    A planarization process and apparatus which employs plasma-enhanced chemical vapor deposition (PECVD) to form plarnarization films of dielectric or conductive carbonaceous material on step-like substrates.

  2. Metallo-organic decomposition films

    NASA Technical Reports Server (NTRS)

    Gallagher, B. D.

    1985-01-01

    A summary of metallo-organic deposition (MOD) films for solar cells was presented. The MOD materials are metal ions compounded with organic radicals. The technology is evolving quickly for solar cell metallization. Silver compounds, especially silver neodecanoate, were developed which can be applied by thick-film screening, ink-jet printing, spin-on, spray, or dip methods. Some of the advantages of MOD are: high uniform metal content, lower firing temperatures, decomposition without leaving a carbon deposit or toxic materials, and a film that is stable under ambient conditions. Molecular design criteria were explained along with compounds formulated to date, and the accompanying reactions for these compounds. Phase stability and the other experimental and analytic results of MOD films were presented.

  3. Ultra thin gage plastic film

    NASA Technical Reports Server (NTRS)

    Cox, D. W., Jr.; Struble, A. D.

    1971-01-01

    Process utilizing specially modified conventional equipment, with changes in process temperature, pressure, and cooling requirements produces ultra thin 1.56 micron /0.0614 mil/ thick polyethylene film.

  4. Film Growth on Nanoporous Substrate

    NASA Astrophysics Data System (ADS)

    Zhang, Xue; Joy, James; Zhao, Chenwei; Xu, J. M.; Valles, James

    Self-ordered nanoporous anodic aluminum oxide (AAO) provides an easy way to fabricate nano structured material, such as nano wires and nano particles. We employ AAO as substrates and focus on the thermally evaporated film growth on the surface of the substrate. With various materials deposited onto the substrate, we find the films show different structures, e,g. ordered array of nano particles for Lead and nanohoneycomb structure for Silver. We relate the differing behaviors to the difference of surface energy and diffusion constant. To verify this, the effect of substrate temperature on the film growth has been explored and the structure of the film has been successfully changed through the process. We are grateful for the support of NSF Grants No. DMR-1307290.

  5. Interference Colors in Thin Films.

    ERIC Educational Resources Information Center

    Armstrong, H. L.

    1979-01-01

    Explains interference colors in thin films as being due to the removal, or considerable reduction, of a certain color by destructive inteference that results in the complementary color being seen. (GA)

  6. Magnetic Mesoporous Photonic Cellulose Films.

    PubMed

    Giese, Michael; Blusch, Lina K; Schlesinger, Maik; Meseck, Georg R; Hamad, Wadood Y; Arjmand, Mohammad; Sundararaj, Uttandaraman; MacLachlan, Mark J

    2016-09-13

    Novel hybrid materials of cellulose and magnetic nanoparticles (NPs) were synthesized and characterized. The materials combine the chiral nematic structural features of mesoporous photonic cellulose (MPC) with the magnetic properties of cobalt ferrite (CoFe2O4). The photonic, magnetic, and dielectric properties of the hybrid materials were investigated during the dynamic swelling and deswelling of the MPC films. It was observed that the dielectric properties of the generated MPC films increased tremendously following swelling in water, endorsing efficient swelling ability of the generated mesoporous films. The high magnetic permeability of the developed MPC films in conjunction with their superior dielectric properties, predominantly in the swollen state, makes them interesting for electromagnetic interference shielding applications. PMID:27588561

  7. Protection of brittle film against cracking

    NASA Astrophysics Data System (ADS)

    Musil, J.; Sklenka, J.; Čerstvý, R.

    2016-05-01

    This article reports on the protection of the brittle Zrsbnd Sisbnd O film against cracking in bending by the highly elastic top film (over-layer). In experiments the Zrsbnd Sisbnd O films with different elemental composition and structure were used. Both the brittle and highly elastic films were prepared by magnetron sputtering using a dual magnetron. The brittle film easily cracks in bending. On the other hand, the highly elastic film exhibits enhanced resistance to cracking in bending. Main characteristic parameters of both the brittle and highly elastic films are given. Special attention is devoted to the effect of the structure (crystalline, amorphous) of both the brittle and highly elastic top film on the resistance of cracking of the brittle film. It was found that (1) both the X-ray amorphous and crystalline brittle films easily crack in bending, (2) the highly elastic film can have either X-ray amorphous or crystalline structure and (3) both the X-ray amorphous and crystalline, highly elastic top films perfectly protect the brittle films against cracking in bending. The structure, mechanical properties and optical transparency of the brittle and highly elastic sputtered Zrsbnd Sisbnd O films are described in detail. At the end of this article, the principle of the low-temperature formation of the highly elastic films is also explained.

  8. Science and film-making.

    PubMed

    Gouyon, Jean-Baptiste

    2016-01-01

    The essay reviews the literature, mostly historical, on the relationship between science and film-making, with a focus on the science documentary. It then discusses the circumstances of the emergence of the wildlife making-of documentary genre. The thesis examined here is that since the early days of cinema, film-making has evolved from being subordinate to science, to being an equal partner in the production of knowledge, controlled by non-scientists.

  9. Superconductivity in CVD Diamond Films

    NASA Astrophysics Data System (ADS)

    Takano, Yoshihiko

    2005-03-01

    The recent news of superconductivity 2.3K in heavily boron-doped diamond synthesized by high pressure sintering was received with considerable surprise (1). Opening up new possibilities for diamond-based electrical devices, a systematic investigation of these phenomena clearly needs to be achieved. Application of diamond to actual devices requires it to be made into the form of wafers or thin films. We show unambiguous evidence for superconductivity in a heavily boron-doped diamond thin film deposited by the microwave plasma assisted chemical vapor deposition (MPCVD) method (2). An advantage of the MPCVD deposited diamond is that it can control boron concentration in its wider range, particularly in (111) oriented films. The temperature dependence of resistivity for (111) and (100) homoepitaxial thin films were measured under several magnetic fields. Superconducting transition temperatures of (111) homoepitaxial film are determined to be 11.4K for Tc onset and 7.2K for zero resistivity. And the upper critical field is estimated to be about 8T. These values are 2-3 times higher than these ever reported (1,3). On other hand, for (100) homoepitaxial film, Tc onset and Tc zero resistivity were estimated to be 6.3 and 3.2K respectively. The superconductivity in (100) film was strongly suppressed even at the same boron concentration. These differences of superconductivity in film orientation will be discussed. These findings established the superconductivity as a universal property of boron-doped diamond, demonstrating that device application is indeed a feasible challenge. 1. E. A. Ekimov et al. Nature, 428, 542 (2004). 2. Y. Takano et al., Appl. Phys. Lett. 85, 2851 (2004). 3. E. Bustarret et al., ond-mat 0408517.

  10. Variable temperature semiconductor film deposition

    DOEpatents

    Li, Xiaonan; Sheldon, Peter

    1998-01-01

    A method of depositing a semiconductor material on a substrate. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

  11. Variable temperature semiconductor film deposition

    DOEpatents

    Li, X.; Sheldon, P.

    1998-01-27

    A method of depositing a semiconductor material on a substrate is disclosed. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

  12. Covalently networked monolayer-protected nanoparticle films.

    PubMed

    Tognarelli, D J; Miller, Robert B; Pompano, Rebecca R; Loftus, Andrew F; Sheibley, Daniel J; Leopold, Michael C

    2005-11-22

    Covalently networked films of nanoparticles can be assembled on various substrates from functionalized monolayer-protected clusters (MPCs) via ester coupling reactions. Exposure of a specifically modified substrate to alternating solutions of 11-mercaptoundecanoic acid exchanged and 11-mercaptoundecanol exchanged MPCs, in the presence of ester coupling reagents, 1,3-dicyclohexylcarbodiimide and 4-(dimethylamino)pyridine, results in the formation of a multilayer film with ester bridges between individual nanoparticles. These films can be grown in a controlled manner to various thicknesses and exhibit certain properties that are consistent with films having other types of interparticle connectivity, including chemical vapor response behavior and quantized double layer charging. Ester coupling of MPCs into assembled films is a straightforward and highly versatile approach that results in robust films that can endure harsher chemical environments than other types of films. The stability of these covalent films is assessed and compared to other more traditional MPC film assemblies.

  13. Gravity Effects in Condensing and Evaporating Films

    NASA Technical Reports Server (NTRS)

    Hermanson, J. C.; Som, S. M.; Allen, J. S.; Pedersen, P. C.

    2004-01-01

    A general overview of gravity effects in condensing and evaporating films is presented. The topics include: 1) Research Overview; 2) NASA Recognizes Critical Need for Condensation & Evaporation Research to Enable Human Exploration of Space; 3) Condensation and Evaporation Research in Reduced Gravity is Enabling for AHST Technology Needs; 4) Differing Role of Surface Tension on Condensing/Evaporating Film Stability; 5) Fluid Mechanisms in Condensing and Evaporating Films in Reduced Gravity; 6) Research Plan; 7) Experimental Configurations for Condensing Films; 8) Laboratory Condensation Test Cell; 9) Aircraft Experiment; 10) Condensation Study Current Test Conditions; 11) Diagnostics; 12) Shadowgraph Images of Condensing n- pentane Film in Unstable (-1g) Configuration; 13) Condensing n-Pentane Film in Normal Gravity (-1g) at Constant Pressure; 14) Condensing n-Pentane Film in Normal Gravity (-1g) with Cyclic Pressure; 15) Non-condensing Pumped Film in Normal Gravity (-1g); 16) Heat Transfer Coefficient in Developing, Unstable Condensing Film in Normal Gravity; 17) Heat Transfer for Unsteady Condensing Film (-1g); 18) Ultrasound Measurement of Film Thickness N-pentane Film, Stable (+1g) Configuration; and 19) Ultrasound Measurement of Film Thickness N-pentane Film, Unstable (-1g) Configuration.

  14. Thin films under chemical stress

    SciTech Connect

    Not Available

    1991-01-01

    The goal of work on this project has been develop a set of experimental tools to allow investigators interested in transport, binding, and segregation phenomena in composite thin film structures to study these phenomena in situ. Work to-date has focuses on combining novel spatially-directed optical excitation phenomena, e.g. waveguide eigenmodes in thin dielectric slabs, surface plasmon excitations at metal-dielectric interfaces, with standard spectroscopies to understand dynamic processes in thin films and at interfaces. There have been two main scientific thrusts in the work and an additional technical project. In one thrust we have sought to develop experimental tools which will allow us to understand the chemical and physical changes which take place when thin polymer films are placed under chemical stress. In principle this stress may occur because the film is being swelled by a penetrant entrained in solvent, because interfacial reactions are occurring at one or more boundaries within the film structure, or because some component of the film is responding to an external stimulus (e.g. pH, temperature, electric field, or radiation). However all work to-date has focused on obtaining a clearer understanding penetrant transport phenomena. The other thrust has addressed the kinetics of adsorption of model n-alkanoic acids from organic solvents. Both of these thrusts are important within the context of our long-term goal of understanding the behavior of composite structures, composed of thin organic polymer films interspersed with Langmuir-Blodgett (LB) and self-assembled monolayers. In addition there has been a good deal of work to develop the local technical capability to fabricate grating couplers for optical waveguide excitation. This work, which is subsidiary to the main scientific goals of the project, has been successfully completed and will be detailed as well. 41 refs., 10 figs.

  15. Use of a horror film in psychotherapy.

    PubMed

    Turley, J M; Derdeyn, A P

    1990-11-01

    Modern improvements in the technology of cinematic special effects have ushered in a new genre of vivid and graphic horror film. The numerous sequels of these films attest to their popularity among adolescents and young adults. Considerable concern has arisen on the part of parents, professionals, and policymakers regarding adverse effects of these films upon children. The authors discuss the meaning of a horror film to a troubled 13-year-old boy and describe the use of the film in his psychotherapy. The modern horror film serves many of the same functions for the adolescent that the traditional fairy tale serves for the younger child.

  16. Plateau borders of smectic liquid crystalline films

    NASA Astrophysics Data System (ADS)

    Trittel, Torsten; Aldred, Ruth; Stannarius, Ralf

    2011-06-01

    We investigate the geometrical properties of Plateau borders in an arrangement of connected smectic A free standing films. The geometry is chosen such that a circular Plateau border surrounds a planar smectic film and connects it with two smectic catenoids. It is demonstrated that, similar to soap films, the smectic film geometry can be described by a negative line tension of the circular contact region. Thus, the equilibrium angle between the films depends upon the liquid content in this region, and with increasing liquid content, deviations from Plateau's rule are observed. The experimental results are qualitatively comparable to soap films. A possible origin of slight quantitative differences is discussed.

  17. Modeling Tear Film Evaporation and Breakup with Duplex Films

    NASA Astrophysics Data System (ADS)

    Stapf, Michael; Braun, Richard; Begley, Carolyn; Driscoll, Tobin; King-Smith, Peter Ewen

    2015-11-01

    Tear film thinning, hyperosmolarity, and breakup can irritate and damage the ocular surface. Recent research hypothesizes deficiencies in the lipid layer may cause locally increased evaporation, inducing conditions for breakup. We consider a model for team film evolution incorporating two mobile fluid layers, the aqueous and lipid layers. In addition, we include the effects of salt concentration, osmosis, evaporation as modified by the lipid layer, and the polar portion of the lipid layer. Numerically solving the resulting model, we explore the conditions for tear film breakup and analyze the response of the system to changes in our parameters. Our studies indicate sufficiently fast peak values or sufficiently wide areas of evaporation promote TBU, as does diffusion of solutes. In addition, the Marangoni effect representing polar lipids dominates viscous dissipation from the non-polar lipid layer in the model. This work was supported in part by NSF grant 1412085 and NIH grant 1R01EY021794.

  18. Drying of poloxamer hydrogel films.

    PubMed

    Gu, Zhiyong; Alexandridis, Paschalis

    2004-06-01

    The drying of hydrogel films formed by Poloxamer 407 poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) amphiphilic block copolymer was investigated at various air relative humidity (RH) conditions ranging from 11 to 97%. Initially, the amount of water lost increased linearly with the drying time. After this linear region (stage I), a nonlinear behavior was observed (stage II). The drying rate increased with decreasing RH, thus greatly shortening the drying time. A decrease of the film thickness also shortened the drying time; however, the drying mechanism did not change. Three models for one-dimensional water diffusion were used to fit the experimental results at different RH conditions and film thicknesses. Model 1 assumes semi-infinite medium and constant diffusion coefficient, and fits very well the data in stage I of the drying process. The fitted water diffusion coefficient (D) is 5 x 10(-10) m(2)/s, whereas the effects of the RH are captured by a proportionality constant (alpha) that appears in the boundary condition. Model 2 considers a finite (constant) film thickness and captures the experimental observations over the whole drying period for the same D and alpha as in Model 1. The analytical solutions available for Models 1 and 2, used together with the experimentally derived model parameters D and alpha, allow for easy estimation of drying time and water loss from Poloxamer hydrogel films of various compositions and thicknesses and at different relative humidities. Numerical solutions for water diffusion under conditions of decreasing film thickness and diffusion coefficient being a function of concentration are also presented (Model 3). It becomes apparent from the fit of the data to the different models that the drying rate is more sensitive to the boundary condition at the film-air interface (represented by alpha) than to the diffusion in the film. It is notable that the alpha values obtained from the fits of the Poloxamer hydrogel drying

  19. Technology of YIG film growth

    SciTech Connect

    Shone, M.

    1985-01-01

    This paper presents information regarding the technology of yttrium iron garnet (YIG) film growth for magnetostatic wave (MSW) applications. The method used for film growth is liquid phase epitaxy from a molten solution of PbO/B/sub 2/O/sub 3/ into which Y/sub 2/O/sub 3/ and Fe/sub 2/O/sub 3/ have been added. An introduction to the crystalline and magnetic features found in YIG is first given. A second section deals with growth techniques and apparatus. In a third section, the melt composition, conditions of growth and homogeneity of as grown material are explored. Growth temperatures varying from 848 to 998 C have been shown to successfully produce YIG films. Possible sources of MSW loss are explored in the fourth section. It is seen that material contamination and physical irregularities may have a negative effect on Delta-H. The final section summarizes the state in which YIG film production now stands. The finding is that although usable films are producible routinely, intrinsic performance is not yet achievable on a regular basis. 53 references.

  20. Thermodynamics of boson quantum films

    NASA Astrophysics Data System (ADS)

    Campbell, C. E.; Clements, B. E.; Krotscheck, E.; Saarela, M.

    1997-02-01

    Theoretical studies of films of liquid 4He adsorbed to strongly attractive plane substrates indicate that the growth of such films occurs through a sequence of first-order phase transitions - ``layering transitions'' - which are a direct consequence of the short-range, hard-core-like interaction between individual helium atoms. The present work examines the effects of temperature on these transitions. At given temperatures, the spinodal points and phase coexistence boundaries are determined for the transitions. Increasing the temperature tends to decrease the coverage span of the transition regions, signaling the possible existence of a critical point terminating the two-phase equilibrium. The layering transitions depend strongly on the helium-substrate potential; the longer-range helium-magnesium potential yields fewer transitions and noticeably lower transition temperatures than the helium-graphite potential. The temperature dependence of the chemical potential, third sound, static structure function, heat capacities, and superfluid densities are reported. The heat capacities are compared to those measured by Greywall and Busch [Phys Rev. Lett. 67, 3535 (1991)]. The thermal broadening of the film's density profile is also discussed. We find that below 1.2 K, thermal broadening is quite weak for coverages away from the layering transitions. The monolayer film experiences the least broadening whereas double-layer and triple-layer films broaden by increasing the local density in the outer tail of their density profiles, while depleting the local density in the inner portion of the outermost layer.

  1. Film Learning in the Classroom

    NASA Astrophysics Data System (ADS)

    Kopp, R.; Liddicoat, J.

    2012-04-01

    Is a picture worth a thousand words? That is a bit of a trick question. We process films and photographs very differently from the way we wrestle with words. They literally work on a different part of our brain, and their testimony is typically weighed differently as well, both in terms of emotional and evidentiary value. Film rhetoric does not quite play with the same deck of cards as classical rhetoric: it shuffles in some jokers and wild cards. To effectively use film in the classroom, faculty need to understand that these visual texts resemble but at the same time differ from written texts. By training faculty in various disciplines in the social and natural sciences to become more aware of not just what a film they are showing in a course says, but how it says it, the faculty can help frame their discussions in a dramatic new way, underlining the crucial connections between content and form that are essential to all critical thinking. There is a real urgency to this task in a world where more and more of the information that students receive is transmitted through visual means from sources of varying degrees of integrity and objectivity. Although this is a life skill that needs to be developed at any age, it most definitely is required at the university level. Recognizing this need, we will share our experience using film in a constructive way for teaching students social and natural sciences at colleges and universities in New York City.

  2. Thin-film metal hydrides.

    PubMed

    Remhof, Arndt; Borgschulte, Andreas

    2008-12-01

    The goal of the medieval alchemist, the chemical transformation of common metals into nobel metals, will forever be a dream. However, key characteristics of metals, such as their electronic band structure and, consequently, their electric, magnetic and optical properties, can be tailored by controlled hydrogen doping. Due to their morphology and well-defined geometry with flat, coplanar surfaces/interfaces, novel phenomena may be observed in thin films. Prominent examples are the eye-catching hydrogen switchable mirror effect, the visualization of solid-state diffusion and the formation of complex surface morphologies. Thin films do not suffer as much from embrittlement and/or decrepitation as bulk materials, allowing the study of cyclic absorption and desorption. Therefore, thin-metal hydride films are used as model systems to study metal-insulator transitions, for high throughput combinatorial research or they may be used as indicator layers to study hydrogen diffusion. They can be found in technological applications as hydrogen sensors, in electrochromic and thermochromic devices. In this review, we discuss the effect of hydrogen loading of thin niobium and yttrium films as archetypical examples of a transition metal and a rare earth metal, respectively. Our focus thereby lies on the hydrogen induced changes of the electronic structure and the morphology of the thin films, their optical properties, the visualization and the control of hydrogen diffusion and on the study of surface phenomena and catalysis.

  3. The Foreign Language Feature Film and Language Teaching Activities.

    ERIC Educational Resources Information Center

    Chappell, Martin

    1986-01-01

    Analysis of foreign language films, featuring consideration of film sequence, image and film analysis, and literary adaptation, is an effective teaching activity with foreign language students. An example illustrates film analysis activities in a first-year French class. (CB)

  4. Hydrogen film/conductive cooling

    NASA Technical Reports Server (NTRS)

    Ewen, R. L.

    1972-01-01

    Small scale nozzle tests using heated nitrogen were run to obtain effectiveness and wall heat transfer data with hydrogen film cooling. Effectiveness data are compared with an entrainment model developed from planar, unaccelerated flow data. Results indicate significant effects due to flow turning and acceleration. With injection velocity effects accounted for explicitly, heat transfer correlation coefficients were found to be the same with and without film cooling when properties are evaluated at an appropriate reference temperature for the local gas composition defined by the coolant effectiveness. A design study for an O2/H2 application with 300 psia (207 N/sq cm) chamber pressure and 1500 lbs (6670 N) thrust indicates an adiabatic wall design requires 4 to 5 percent of the total flow as hydrogen film cooling. Internal regenerative cooling designs were found to offer no reduction in coolant requirements.

  5. Holographic films from carotenoid pigments

    NASA Astrophysics Data System (ADS)

    Toxqui-López, S.; Lecona-Sánchez, J. F.; Santacruz-Vázquez, C.; Olivares-Pérez, A.; Fuentes-Tapia, I.

    2014-02-01

    Carotenoids pigments presents in pineapple can be more than just natural dyes, which is one of the applications that now at day gives the chemical industry. In this research shown that can be used in implementing of holographic recording Films. Therefore we describe the technique how to obtain this kind of pigments trough spay drying of natural pineapple juice, which are then dissolved with water in a proportion of 0.1g to 1mL. The obtained sample is poured into glass substrates using the gravity method, after a drying of 24 hours in laboratory normal conditions the films are ready. The films are characterized by recording transmission holographic gratings (LSR 445 NL 445 nm) and measuring the diffraction efficiency holographic parameter. This recording material has good diffraction efficiency and environmental stability.

  6. LTCC Thick Film Process Characterization

    DOE PAGESBeta

    Girardi, M. A.; Peterson, K. A.; Vianco, P. T.

    2016-05-01

    Low temperature cofired ceramic (LTCC) technology has proven itself in military/space electronics, wireless communication, microsystems, medical and automotive electronics, and sensors. The use of LTCC for high frequency applications is appealing due to its low losses, design flexibility and packaging and integration capability. Moreover, we summarize the LTCC thick film process including some unconventional process steps such as feature machining in the unfired state and thin film definition of outer layer conductors. The LTCC thick film process was characterized to optimize process yields by focusing on these factors: 1) Print location, 2) Print thickness, 3) Drying of tapes and panels,more » 4) Shrinkage upon firing, and 5) Via topography. Statistical methods were used to analyze critical process and product characteristics in the determination towards that optimization goal.« less

  7. Semiconductor-nanocrystal/conjugated polymer thin films

    DOEpatents

    Alivisatos, A. Paul; Dittmer, Janke J.; Huynh, Wendy U.; Milliron, Delia

    2010-08-17

    The invention described herein provides for thin films and methods of making comprising inorganic semiconductor-nanocrystals dispersed in semiconducting-polymers in high loading amounts. The invention also describes photovoltaic devices incorporating the thin films.

  8. A film program in a teaching hospital.

    PubMed

    Meiboom, E

    1973-10-01

    The Martland Hospital Medical Library has for more than a year been conducting a 16mm film program for interns, residents, attending physicians, and nurses as an adjunct to continuing education. It was possible to run this project on a minimal budget because many films are available at little or no cost from governmental agencies, pharmaceutical companies, medical associations, and universities. The program is run on a departmental basis. Films for a department are selected by the chief resident in that department from a list which the librarian has prepared of available films in the specialty involved. The library orders and publicizes the films and transacts all business in connection with them. Films pertinent to clinical practice are preferred. The administration of this program is described in this paper, and a number of film catalogs are evaluated. Criteria for film selection are discussed.

  9. A Film Program in a Teaching Hospital *

    PubMed Central

    Meiboom, Esther

    1973-01-01

    The Martland Hospital Medical Library has for more than a year been conducting a 16mm film program for interns, residents, attending physicians, and nurses as an adjunct to continuing education. It was possible to run this project on a minimal budget because many films are available at little or no cost from governmental agencies, pharmaceutical companies, medical associations, and universities. The program is run on a departmental basis. Films for a department are selected by the chief resident in that department from a list which the librarian has prepared of available films in the specialty involved. The library orders and publicizes the films and transacts all business in connection with them. Films pertinent to clinical practice are preferred. The administration of this program is described in this paper, and a number of film catalogs are evaluated. Criteria for film selection are discussed. PMID:4800293

  10. Soap Films as 1D waveguides

    NASA Astrophysics Data System (ADS)

    Emile, Olivier; Emile, Janine

    2014-01-01

    Laser light is injected in a free standing horizontal draining soap film through the glass frame sustaining the film. Two propagation regimes are clearly identified depending on the film thickness. At the beginning of the drainage, the soap film behaves as a multimode-one dimensional optofiuidic waveguide. In particular, we observe that the injected light creates a bottleneck in the film and part of the injected light is refracted leading to whiskers. At the end of the drainage where the film thickness is below 1μm, there is a strong selection among the various possible optical modes in the film, and part of the light is defiected. This leads to a self selection of the mode propagation inside the film.

  11. Heat-shrinkable film improves adhesive bonds

    NASA Technical Reports Server (NTRS)

    Johns, J. M.; Reed, M. W.

    1980-01-01

    Pressure is applied during adhesive bonding by wrapping parts in heat-shrinkable plastic film. Film eliminates need to vacuum bag or heat parts in expensive autoclave. With procedure, operators are trained quickly, and no special skills are required.

  12. Semiconductor-nanocrystal/conjugated polymer thin films

    DOEpatents

    Alivisatos, A. Paul; Dittmer, Janke J.; Huynh, Wendy U.; Milliron, Delia

    2014-06-17

    The invention described herein provides for thin films and methods of making comprising inorganic semiconductor-nanocrystals dispersed in semiconducting-polymers in high loading amounts. The invention also describes photovoltaic devices incorporating the thin films.

  13. Reprint Characteristics of Non-Silver Films.

    ERIC Educational Resources Information Center

    Microform Review, 1990

    1990-01-01

    Describes reprint characteristics of diazo and vesicular films. Use with microform reader-printers and autogeneration of copies are discussed, and methods of dealing with the unusual reprint behavior of these films are outlined. (MES)

  14. Electrically Responsive Soft Photonic BCP Films

    NASA Astrophysics Data System (ADS)

    Noro, Atsushi; Ohno, Maho; Matsushita, Yushu

    We report electro-responsive soft photonic films composed of lamellar-forming block copolymer/nonvolatile protic solvent/metal salt. Thin films of polystyrene-b-poly(2-vinylpyridine) (SP, Mn =153k, φS =0.57, PDI =1.18) were prepared by spin-coating of the solutions on ITO glass substrates, then mixture of glycol-based solvent and lithium bis(trifluoro methanesulfonyl)imidide (LiTFSI) was added to the thin films, producing soft photonic films. If needed, the spin-coated SP thin films were ionized by iodomethane before addition of the mixture of glycol-based solvent and LiTFSI. TEM observations and U-SAXS measurements revealed that these photonic films kept lamellar structures after addition of the solvent, that is, the P phase was swollen selectively with the solvent. Systematic electro-responsiveness of photonic properties of the films was also confirmed by applying voltages to the films.

  15. Hochschule fur Film und Fernsehen (Babelsberg).

    ERIC Educational Resources Information Center

    Neumann, Roland

    1992-01-01

    Describes the Hochschule fur Film und Fernsehen, an institution of higher education for the study of film and television production in Babelsberg, Germany (formerly the German Democratic Republic). Discusses the major reorientations in the school caused by Germany's reunification. (SR)

  16. Thin film-coated polymer webs

    DOEpatents

    Wenz, Robert P.; Weber, Michael F.; Arudi, Ravindra L.

    1992-02-04

    The present invention relates to thin film-coated polymer webs, and more particularly to thin film electronic devices supported upon a polymer web, wherein the polymer web is treated with a purifying amount of electron beam radiation.

  17. US/Russian Joint Film Test

    NASA Technical Reports Server (NTRS)

    Slater, Richard

    1996-01-01

    A joint U.S./Russian film test was conducted during MIR Mission 18 to evaluate the effects of radiation on photographic film during long-duration space flights. Two duplicate sets of film were flown on this MIR mission: one set was processed and evaluated by the NASA/JSC Photographic Laboratory, and the other by the RKK Energia's Photographic Laboratory in Moscow. This preliminary report includes only the results of the JSC evaluation (excluding the SN-10 film which was not available for evaluation at the time this report was written). The final report will include an evaluation by JSC of the SN-10 film and an evaluation of the test data by the RKK Energia. ISC's evaluation of the test data showed the positive film flown was damaged very little when exposed to approximately 8 rads of radiation. Two of the three negative films were significantly damaged and the third film was damaged only moderately.

  18. Vacuum casting of thick polymeric films

    NASA Technical Reports Server (NTRS)

    Cuddihy, E. F.; Moacanin, J.

    1979-01-01

    Bubble formation and layering, which often plague vacuum-evaporated films, are prevented by properly regulating process parameters. Vacuum casting may be applicable to forming thick films of other polymer/solvent solutions.

  19. Fire resistant films for aircraft applications

    NASA Technical Reports Server (NTRS)

    Kourtides, D. A.

    1983-01-01

    Alternative sandwich panel decorative films were investigated as replacements for the polyvinyl fluoride currently used in aircraft interiors. Candidate films were studied for flammability, smoke emission, toxic gas emission, flame spread, and suitability as a printing surface for the decorative acrylic ink system. Several of the candidate films tested were flame modified polyvinyl fluoride, polyvinylidene fluoride, polyimide, polyamide, polysulfone, polyphenylsulfone, polyethersulfone, polybenzimidazole, polycarbonate, polyparabanic acid, polyphosphazene, polyetheretherketon, and polyester. The films were evaluated as pure films only, films silk-screened with an acrylic ink, and films adhered to a phenolic fiberglass substrate. Films which exhibited the highest fire resistant properties included PEEK polyetheretherketon, Aramid polyamide, and ISO-BPE polyester. Previously announced in STAR as N83-22320

  20. A Cooperative Film Effort in Colorado

    ERIC Educational Resources Information Center

    Spetnagel, H. T.; And Others

    1972-01-01

    The mass communications department of the University of Denver assisted in producing a film on community colleges in Colorado which improved the film students' cinema skills while providing greater exposure for the community college system. (NF)

  1. Low work function, stable thin films

    DOEpatents

    Dinh, Long N.; McLean, II, William; Balooch, Mehdi; Fehring, Jr., Edward J.; Schildbach, Marcus A.

    2000-01-01

    Generation of low work function, stable compound thin films by laser ablation. Compound thin films with low work function can be synthesized by simultaneously laser ablating silicon, for example, and thermal evaporating an alkali metal into an oxygen environment. For example, the compound thin film may be composed of Si/Cs/O. The work functions of the thin films can be varied by changing the silicon/alkali metal/oxygen ratio. Low work functions of the compound thin films deposited on silicon substrates were confirmed by ultraviolet photoelectron spectroscopy (UPS). The compound thin films are stable up to 500.degree. C. as measured by x-ray photoelectron spectroscopy (XPS). Tests have established that for certain chemical compositions and annealing temperatures of the compound thin films, negative electron affinity (NEA) was detected. The low work function, stable compound thin films can be utilized in solar cells, field emission flat panel displays, electron guns, and cold cathode electron guns.

  2. Electrostatic thin film chemical and biological sensor

    DOEpatents

    Prelas, Mark A.; Ghosh, Tushar K.; Tompson, Jr., Robert V.; Viswanath, Dabir; Loyalka, Sudarshan K.

    2010-01-19

    A chemical and biological agent sensor includes an electrostatic thin film supported by a substrate. The film includes an electrostatic charged surface to attract predetermined biological and chemical agents of interest. A charge collector associated with said electrostatic thin film collects charge associated with surface defects in the electrostatic film induced by the predetermined biological and chemical agents of interest. A preferred sensing system includes a charge based deep level transient spectroscopy system to read out charges from the film and match responses to data sets regarding the agents of interest. A method for sensing biological and chemical agents includes providing a thin sensing film having a predetermined electrostatic charge. The film is exposed to an environment suspected of containing the biological and chemical agents. Quantum surface effects on the film are measured. Biological and/or chemical agents can be detected, identified and quantified based on the measured quantum surface effects.

  3. Laser tracks in rainbow films on water

    SciTech Connect

    Startsev, Aleksandr V; Stoilov, Yurii Yu

    2012-08-31

    It is found that narrow non-diverging laser tracks, earlier studied in free soap films, can also arise in thin rainbow films, e.g., of petrol, on water. (laser applications and other topics in quantum electronics)

  4. Predictors of Horror Film Attendance and Appeal: An Analysis of the Audience for Frightening Films.

    ERIC Educational Resources Information Center

    Tamborini, Ron; Stiff, James

    1987-01-01

    Analyzes the appeal of horror films. Develops a model that finds that important factors in the horror film's appeal are the audience's desire to experience the satisfying resolutions and to see the destruction usually found in these films and the sensation-seeking personality traits of audience members for these films. (NKA)

  5. 36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

  6. 36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

  7. 36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

  8. 36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

  9. The Native Forum at the 2001 Sundance Film Festival: Redefining Indigenous Film.

    ERIC Educational Resources Information Center

    McDonald, Christine

    2001-01-01

    Describes films from the Native Forum of the 2001 Sundance Film Festival, focusing on the feature film, "Christmas in the Clouds," and also looking at a variety of documentaries on indigenous populations in North America and Mexico. Presents a brief annotation and contact information for each film. (SM)

  10. The American Film Heritage; Impressions from the American Film Institute Archives.

    ERIC Educational Resources Information Center

    Shales, Tom; And Others

    The American Film Institute has an archive which presently contains more than 9,000 films, many of them rare. The articles in this volume are based on some of the films in the collection. Among the topics of these essays are: pioneers like D. W. Griffith and Thomas H. Ince, treatment of blacks and Indians in films, development of the techniques…

  11. 36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

  12. Film shape calculations on supercomputers

    NASA Technical Reports Server (NTRS)

    Hamrock, B. J.

    1982-01-01

    Both scalar and vector operations are described to demonstrate usefulness of supercomputers (computers with peak computing speeds exceeding 100 million operative per second) in solving tribological problems. A simple kernel of the film shape calculations in an elastohydrodynamic lubricated rectangular contact is presented and the relevant equations are described. Both scalar and vector versions of the film shape code are presented. The run times of the two types of code indicate that over a 50-to-1 speedup of scalar to vector computational time for vector lengths typically used in elastohydrodynamic lubrication analysis is obtained.

  13. Thin film buried anode battery

    DOEpatents

    Lee, Se-Hee; Tracy, C. Edwin; Liu, Ping

    2009-12-15

    A reverse configuration, lithium thin film battery (300) having a buried lithium anode layer (305) and process for making the same. The present invention is formed from a precursor composite structure (200) made by depositing electrolyte layer (204) onto substrate (201), followed by sequential depositions of cathode layer (203) and current collector (202) on the electrolyte layer. The precursor is subjected to an activation step, wherein a buried lithium anode layer (305) is formed via electroplating a lithium anode layer at the interface of substrate (201) and electrolyte film (204). The electroplating is accomplished by applying a current between anode current collector (201) and cathode current collector (202).

  14. Liquid film target impingement scrubber

    DOEpatents

    McDowell, William J.; Coleman, Charles F.

    1977-03-15

    An improved liquid film impingement scrubber is provided wherein particulates suspended in a gas are removed by jetting the particle-containing gas onto a relatively small thin liquid layer impingement target surface. The impingement target is in the form of a porous material which allows a suitable contacting liquid from a pressurized chamber to exude therethrough to form a thin liquid film target surface. The gas-supported particles collected by impingement of the gas on the target are continuously removed and flushed from the system by the liquid flow through each of a number of pores in the target.

  15. The Uses of Artful Film in the Classroom.

    ERIC Educational Resources Information Center

    Gaffney, Maureen

    1986-01-01

    Offers information about aesthetic films, their study in class as an art form, and the procurement of such works from the Media Center for Children in New York. Compares film to literature and contrasts the language of film with verbal language. Lists some of the best films tested with children and film distributors. Outlines film discussion…

  16. Film handling procedures for Apollo 17 lunar sounder

    NASA Technical Reports Server (NTRS)

    Weinstein, M. S.

    1972-01-01

    Film handling procedures for the Apollo 17 Lunar Sounder are itemized, including purchase of flight film, establishment of processing standards, transportation of flight films, flight film certification, application of pre- and post-sensitometry, film loading and downloading, film processing, titling, and duplication.

  17. Biaxially oriented film on flexible polymeric substrate

    DOEpatents

    Finkikoglu, Alp T.; Matias, Vladimir

    2009-10-13

    A flexible polymer-based template having a biaxially oriented film grown on the surface of a polymeric substrate. The template having the biaxially oriented film can be used for further epitaxial growth of films of interest for applications such as photovoltaic cells, light emitting diodes, and the like. Methods of forming such a flexible template and providing the polymeric substrate with a biaxially oriented film deposited thereon are also described.

  18. Silicon nanocrystal inks, films, and methods

    SciTech Connect

    Wheeler, Lance Michael; Kortshagen, Uwe Richard

    2015-09-01

    Silicon nanocrystal inks and films, and methods of making and using silicon nanocrystal inks and films, are disclosed herein. In certain embodiments the nanocrystal inks and films include halide-terminated (e.g., chloride-terminated) and/or halide and hydrogen-terminated nanocrystals of silicon or alloys thereof. Silicon nanocrystal inks and films can be used, for example, to prepare semiconductor devices.

  19. Flexible thin metal film thermal sensing system

    NASA Technical Reports Server (NTRS)

    Thomsen, Donald L. (Inventor)

    2010-01-01

    A flexible thin metal film thermal sensing system is provided. A self-metallized polymeric film has a polymeric film region and a metal surface disposed thereon. A layer of electrically-conductive metal is deposited directly onto the self-metallized polymeric film's metal surface. Coupled to at least one of the metal surface and the layer of electrically-conductive metal is a device/system for measuring an electrical characteristic associated therewith as an indication of temperature.

  20. Chemical-Vapor-Deposited Diamond Film

    NASA Technical Reports Server (NTRS)

    Miyoshi, Kazuhisa

    1999-01-01

    This chapter describes the nature of clean and contaminated diamond surfaces, Chemical-vapor-deposited (CVD) diamond film deposition technology, analytical techniques and the results of research on CVD diamond films, and the general properties of CVD diamond films. Further, it describes the friction and wear properties of CVD diamond films in the atmosphere, in a controlled nitrogen environment, and in an ultra-high-vacuum environment.

  1. Film Music: Implications for Instructional Films and Television.

    ERIC Educational Resources Information Center

    Hlynka, D.

    This paper provides a critical review of the behavioral research on film music, indicates that there is a visual bias in media attribute research which needs to be balanced, and provides media producers and instructional developers with a theoretical basis and practical guidelines for using music in audiovisual presentations. The question of film…

  2. NFL Films audio, video, and film production facilities

    NASA Astrophysics Data System (ADS)

    Berger, Russ; Schrag, Richard C.; Ridings, Jason J.

    2003-04-01

    The new NFL Films 200,000 sq. ft. headquarters is home for the critically acclaimed film production that preserves the NFL's visual legacy week-to-week during the football season, and is also the technical plant that processes and archives football footage from the earliest recorded media to the current network broadcasts. No other company in the country shoots more film than NFL Films, and the inclusion of cutting-edge video and audio formats demands that their technical spaces continually integrate the latest in the ever-changing world of technology. This facility houses a staggering array of acoustically sensitive spaces where music and sound are equal partners with the visual medium. Over 90,000 sq. ft. of sound critical technical space is comprised of an array of sound stages, music scoring stages, audio control rooms, music writing rooms, recording studios, mixing theaters, video production control rooms, editing suites, and a screening theater. Every production control space in the building is designed to monitor and produce multi channel surround sound audio. An overview of the architectural and acoustical design challenges encountered for each sophisticated listening, recording, viewing, editing, and sound critical environment will be discussed.

  3. Cinematography; A Guide for Film Makers and Film Teachers.

    ERIC Educational Resources Information Center

    Malkiewicz, J. Kris

    Concentrating on the work of the cinematographer--the man behind the camera or in charge of the shooting--this book also touches on techniques of sound recording, cutting, and production logistics. Technical discussions designed to provide the basic principles and techniques of cinematography are presented about cameras, films and sensitometry,…

  4. International Index to Film Periodicals 1972.

    ERIC Educational Resources Information Center

    Jones, Karen, Ed.

    Fifty-nine film journals, selected as being the most representative and significant of their respective countries, are indexed in this annual publication of the International Federation of Film Archives (IFFA). The index is the result of the collaborative efforts of film archivists working in 24 countries under the direction of the Documentation…

  5. The Technique of Film Editing. Enlarged Edition.

    ERIC Educational Resources Information Center

    Reisz, Karel; Millar, Gavin

    Film editing is discussed from the point of view, not only of the person in the cutting room, but also of the person who has responsibility for the final film. Part I outlines the history of editing from the silent film to 1953. It discusses the practice of editing for action, dialogue, comedy, and montage sequences, as well as in documentaries,…

  6. Hollywood Films as a Teaching Tool.

    ERIC Educational Resources Information Center

    Rebhorn, Marlette

    This project seeks to bring an immediacy and interest to historical events through the use of Hollywood feature films. Some of the films used to promote interest in history are "Inherit the Wind,""All the President's Men,""The Birth of a Nation," and "Reds." Films used in the class should be available on videocassettes because they are less…

  7. The Role of Film in Development.

    ERIC Educational Resources Information Center

    Hopkinson, Peter

    Addressed to those connected with filmmaking and information dissemination in developing countries, this manual offers practical advice in initiating and maintaining a filmmaking program. In addition to general information on film history and film potential, the manual presents a step-by-step case history of an instructional film made in India to…

  8. Effects of annealing electrodeposited bismuth Telluride films

    NASA Technical Reports Server (NTRS)

    Snyder, J.; Stoltz, N. G.

    2002-01-01

    Thermoelectric thin films exhibit different qualities when compared with bulk materials. The goal however is to achieve thermoelectric properties of bulk materials from electrodeposited thin films. Thin films are produced by electrochemical deposition at room temperature. In order to optimize thermoelectric figure of merit proper carrierconcentration must be obtained.

  9. Teaching World Music through Feature Films

    ERIC Educational Resources Information Center

    Lum, Chee-Hoo

    2009-01-01

    When used effectively, feature films can bring a plethora of visual and aural stimulation to students and enhance their learning about world cultures. Feature films can take students to places, sights, and sounds that they have yet to experience. After watching these films, students might become new admirers or even keen followers of the subject…

  10. Film Language: A Student-Made Dictionary.

    ERIC Educational Resources Information Center

    Poteet, G. Howard

    1967-01-01

    The failure of verbal descriptions to convey an understanding of film terminology led to a student production of a 20-minute color film that defines various film methods by illustrating them. A technique is shown on the screen and simultaneous soundtrack narration explains how this technique can be used. When the narration lasts longer than the…

  11. Fruit and vegetable films and uses thereof

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The present invention is directed to monolayer, bilayer, and multilayer films made from fruit, vegetable or a combination thereof, which films have the thinness, strength, flexibility and crispness to serve as alternates or substitutes for seaweed-based films such as nori, while providing nutrition ...

  12. Method of producing thin cellulose nitrate film

    DOEpatents

    Lupica, S.B.

    1975-12-23

    An improved method for forming a thin nitrocellulose film of reproducible thickness is described. The film is a cellulose nitrate film, 10 to 20 microns in thickness, cast from a solution of cellulose nitrate in tetrahydrofuran, said solution containing from 7 to 15 percent, by weight, of dioctyl phthalate, said cellulose nitrate having a nitrogen content of from 10 to 13 percent.

  13. Toward an Historical Methodology for Film Scholarship

    ERIC Educational Resources Information Center

    Isenberg, Michael T.

    1975-01-01

    From among the possible approaches to film study -- through the communicator, the medium, and the audience -- the process and motives involved in the communicator's manufacture of the film itself, is the strongest hook upon which to hang a methodology of film study. (JH)

  14. The World Encyclopedia of the Film.

    ERIC Educational Resources Information Center

    Smith, John M., Ed.; Cawkwell, Tim, Ed.

    This reference book contains an alphabetically arranged list of world film stars, producers, directors, and other filmmakers and an index of important films from 1898 to 1972. Each of the major entries notes brief biographical data, with dates of important events in the lives of the subjects, and the titles and dates of the films to which the…

  15. The Development of a Semiotic of Film.

    ERIC Educational Resources Information Center

    Worth, Sol

    The process of film making can be thought of as beginning with a person's feeling or concern about something. To communicate this feeling to others, the film maker (sender) must develop an organic unit which will provide a vehicle that can embody the feeling/Story-Organism. The film maker selects and orders a series of signs, images, or events…

  16. Film and History, Foxes and Hedgehogs.

    ERIC Educational Resources Information Center

    Doherty, Thomas

    2002-01-01

    Discusses the treatment of historical events within Hollywood (California) films. Addresses the idea of verisimilitude, or the true replication of history in all aspects. Examines films such as: "Pearl Harbor,""Park Row,""Verboten!,""October Sky," and "Thirteen Days," to demonstrate how films portray history. (CMK)

  17. Polyvinylidene fluoride film as a capacitor dielectric

    NASA Technical Reports Server (NTRS)

    Dematos, H. V.

    1981-01-01

    Thin strips of polyvinylidene fluoride film (PVDF) with vacuum deposited electrodes were made into capacitors by conventional winding and fabrication techniques. These devices were used to identify and evaluate the performance characteristics offered by the PVDF in metallized film capacitors. Variations in capacitor parameters with temperature and frequence were evaluated and compared with other dielectric films. Their impact on capacitor applications is discussed.

  18. IMC/RMC Network Professional Film Collection.

    ERIC Educational Resources Information Center

    New York State Education Dept., Albany. Special Education Instructional Materials Center.

    The compilation is a comprehensive listing of films available from the centers in the Instructional Materials Centers/Regional Media Centers (IMC/RMC) Network. Each IMC/RMC location is given a numerical code in a preliminary listing. These numerical codes are used within the film listing, which is arranged alphabetically according to film titles,…

  19. Shakespeare on Film in the Classroom.

    ERIC Educational Resources Information Center

    Mullin, Michael

    A course at the University of Illinois entitled "Shakespeare on Film" is discussed briefly, and an annotated list of Shakespeare films for the classroom teacher is provided in this paper. Thirteen films are listed: three versions of "Hamlet,""Henry V,""Julius Caesar," four versions of "Macbeth,""A Midsummer Night's Dream,""Othello,""Romeo and…

  20. 21 CFR 892.1840 - Radiographic film.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1840 Radiographic film. (a) Identification. Radiographic film is a device that consists of a thin sheet of radiotransparent material coated on one or both... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Radiographic film. 892.1840 Section 892.1840...

  1. 21 CFR 892.1840 - Radiographic film.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1840 Radiographic film. (a) Identification. Radiographic film is a device that consists of a thin sheet of radiotransparent material coated on one or both... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Radiographic film. 892.1840 Section 892.1840...

  2. 21 CFR 892.1840 - Radiographic film.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1840 Radiographic film. (a) Identification. Radiographic film is a device that consists of a thin sheet of radiotransparent material coated on one or both... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Radiographic film. 892.1840 Section 892.1840...

  3. 21 CFR 892.1840 - Radiographic film.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1840 Radiographic film. (a) Identification. Radiographic film is a device that consists of a thin sheet of radiotransparent material coated on one or both... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Radiographic film. 892.1840 Section 892.1840...

  4. A New Breed of Environmental Film

    ERIC Educational Resources Information Center

    Malamud, Randy

    2008-01-01

    In this article, the author reports how today's environmental film festivals feature a new breed of documentary that offer nuanced narratives about intricate technologies. The author relates that the environmental films he grew up with sedately depicted the quiet sublimity of the wilderness. Today's films, the author observes, aim far beyond a…

  5. Teaching the Shakespearean Film: Olivier's "Henry V."

    ERIC Educational Resources Information Center

    Gerlach, John

    For at least two kinds of literature instructors, classroom use of a film derived from a Shakespeare play is potentially promising: a Shakespeare course instructor can present one attempt to visualize the implications of the printed word, and a teacher of a course which compares film and literature has at least one respectable film adaptation of a…

  6. A Guide to Films About Development.

    ERIC Educational Resources Information Center

    American Freedom from Hunger Foundation, Washington, DC.

    This resource guide contains complete descriptions of films about poverty and development both in the United States and in poor nations. The films are selected for use in classrooms, workshops, and community seminars and annotations summarize film content. Topics related to development in the United States include perspectives, poverty, realities…

  7. 7 CFR 2902.27 - Films.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... applications. (2) Films for which preferred procurement applies are: (i) Semi-durable films. Films that are... manufacturers of these qualifying biobased products provide information for the BioPreferred Web site of... product contains any recovered material, in addition to biobased ingredients, and performance...

  8. A Study on Environmental Education Films.

    ERIC Educational Resources Information Center

    Gerba, Diana

    The degree of communication between the film industry and educators and its effect on the future directions of environmental education films are the focus of this report. Separate surveys were mailed to 100 film industry producers and distributors and 150 elementary and secondary educators in Maine, Kansas, Pennsylvania, California, and Alabama.…

  9. 21 CFR 892.1840 - Radiographic film.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Radiographic film. 892.1840 Section 892.1840 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1840 Radiographic film. (a) Identification. Radiographic film is a device that consists of a thin sheet of radiotransparent material coated on one or...

  10. Wrinkling of Stretched Films: Compressive Stress

    NASA Technical Reports Server (NTRS)

    Zak, M. A.

    1982-01-01

    Recent report presents derivation of equations of motion for wrinkles forming in planar films under compressive in-plane stress. Study was prompted by wrinkling of thin film solar-cell arrays with consequent reduction in collection efficiency. Lack of adequate theoretical understanding made it difficult to design large film structures and specify oscillation tests for large solar array systems.

  11. Evaluation and mitigation of potential errors in radiochromic film dosimetry due to film curvature at scanning.

    PubMed

    Palmer, Antony L; Bradley, David A; Nisbet, Andrew

    2015-03-08

    This work considers a previously overlooked uncertainty present in film dosimetry which results from moderate curvature of films during the scanning process. Small film samples are particularly susceptible to film curling which may be undetected or deemed insignificant. In this study, we consider test cases with controlled induced curvature of film and with film raised horizontally above the scanner plate. We also evaluate the difference in scans of a film irradiated with a typical brachytherapy dose distribution with the film naturally curved and with the film held flat on the scanner. Typical naturally occurring curvature of film at scanning, giving rise to a maximum height 1 to 2 mm above the scan plane, may introduce dose errors of 1% to 4%, and considerably reduce gamma evaluation passing rates when comparing film-measured doses with treatment planning system-calculated dose distributions, a common application of film dosimetry in radiotherapy. The use of a triple-channel dosimetry algorithm appeared to mitigate the error due to film curvature compared to conventional single-channel film dosimetry. The change in pixel value and calibrated reported dose with film curling or height above the scanner plate may be due to variations in illumination characteristics, optical disturbances, or a Callier-type effect. There is a clear requirement for physically flat films at scanning to avoid the introduction of a substantial error source in film dosimetry. Particularly for small film samples, a compression glass plate above the film is recommended to ensure flat-film scanning. This effect has been overlooked to date in the literature.

  12. Infrared film for aerial photography

    USGS Publications Warehouse

    Anderson, William H.

    1979-01-01

    Considerable interest has developed recently in the use of aerial photographs for agricultural management. Even the simplest hand-held aerial photographs, especially those taken with color infrared film, often provide information not ordinarily available through routine ground observation. When fields are viewed from above, patterns and variations become more apparent, often allowing problems to be spotted which otherwise may go undetected.

  13. Making Films without a Camera.

    ERIC Educational Resources Information Center

    Cox, Carole

    1980-01-01

    Describes draw-on filmmaking as an exciting way to introduce children to the plastic, fluid nature of the film medium, to develop their appreciation and understanding of divergent cinematic techniques and themes, and to invite them into the dream world of filmmaking without the need for a camera. (AEA)

  14. Remote Sensing: A Film Review.

    ERIC Educational Resources Information Center

    Carter, David J.

    1986-01-01

    Reviews the content of 19 films on remote sensing published between 1973 and 1980. Concludes that they are overly simplistic, notably outdated, and generally too optimistic about the potential of remote sensing from space for resource exploration and environmental problem-solving. Provides names and addresses of more current remote sensing…

  15. Black Women in Film Symposium

    ERIC Educational Resources Information Center

    Smith, Barbara

    1974-01-01

    Describes a symposium sponsored in April of last year by the Afro-American and American Studies Departments at Boston University on "Black Image in Films, Stereotyping and Self-Perception"; participants included Susan Batson, Cynthia Belgrave, Ruby Dee, Beah Richards, and Cicely Tyson. (Author/JM)

  16. Scribable coating for plastic films

    NASA Technical Reports Server (NTRS)

    Clark, R. T.

    1967-01-01

    Scribable opaque coating for transparent plastic film tape is not affected by aging, vacuum, and moderate temperature extremes. It consists of titanium dioxide, a water-compatible acrylic polymer emulsion, and a detergent. The coating mixture is readily dispersed in water before it is dried.

  17. Evaluating Solid-Lubricant Films

    NASA Technical Reports Server (NTRS)

    Fusaro, Robert L.

    1988-01-01

    Report describes experimental techniques for measuring properties of solid-lubricant films. Discusses experimental parameters. Reviews basic pin-on-disk configurations and methods of preparing disks and applying solid lubricants. Techniques for constant-temperature testing, low-contact-stress testing, and temperature-versus-time testing presented. Suggests methods of measuring pin-wear volume and recommends ways of presenting data.

  18. Methane production by attached film

    DOEpatents

    Jewell, William J.

    1981-01-01

    A method for purifying wastewater of biodegradable organics by converting the organics to methane and carbon dioxide gases is disclosed, characterized by the use of an anaerobic attached film expanded bed reactor for the reaction process. Dilute organic waste material is initially seeded with a heterogeneous anaerobic bacteria population including a methane-producing bacteria. The seeded organic waste material is introduced into the bottom of the expanded bed reactor which includes a particulate support media coated with a polysaccharide film. A low-velocity upward flow of the organic waste material is established through the bed during which the attached bacterial film reacts with the organic material to produce methane and carbon dioxide gases, purified water, and a small amount of residual effluent material. The residual effluent material is filtered by the film as it flows upwardly through the reactor bed. In a preferred embodiment, partially treated effluent material is recycled from the top of the bed to the bottom of the bed for further treatment. The methane and carbon dioxide gases are then separated from the residual effluent material and purified water.

  19. Thin film polymeric gel electrolytes

    DOEpatents

    Derzon, Dora K.; Arnold, Jr., Charles; Delnick, Frank M.

    1996-01-01

    Novel hybrid thin film electrolyte, based on an organonitrile solvent system, which are compositionally stable, environmentally safe, can be produced efficiently in large quantity and which, because of their high conductivities .apprxeq.10.sup.-3 .OMEGA..sup.-1 cm.sup.-1 are useful as electrolytes for rechargeable lithium batteries.

  20. Films/Videos for Adults.

    ERIC Educational Resources Information Center

    Stanford, Beverly Hardcastle

    1993-01-01

    Reviews six films designed for adults released between 1988 and 1992, most of which focus on the challenges that children face, including (1) See What I'm Saying; (2) Something Magical; (3) We Have Something to Say: Children, Computers, and Special Education; (4) Shortchanging Girls, Shortchanging America; (5) Take Me to Your Leaders; and (6) The…

  1. Thin-Film Selective Emitter

    NASA Technical Reports Server (NTRS)

    Chubb, Donald L.; Lowe, Roland A.

    1993-01-01

    Direct conversion of thermal energy into electrical energy using a photovoltaic cell is called thermophotovoltaic energy conversion. One way to make this an efficient process is to have the thermal energy source be an efficient selective emitter of radiation. The emission must be near the band-gap energy of the photovoltaic cell. One possible method to achieve an efficient selective emitter is the use of a thin film of rare-earth oxides. The determination of the efficiency of such an emitter requires analysis of the spectral emittance of the thin film including scattering and reflectance at the vacuum-film and film-substrate interfaces. Emitter efficiencies (power emitted in emission band/total emitted power) in the range 0.35-0.7 are predicted. There is an optimum optical depth to obtain maximum efficiency. High emitter efficiencies are attained only for low (less than 0.05) substrate emittance values, both with and without scattering. The low substrate emittance required for high efficiency limits the choice of substrate materials to highly reflective metals or high-transmission materials such as sapphire.

  2. Thermoplastic film prevents proppant flowback

    SciTech Connect

    Nguyen, P.D.; Weaver, J.D.; Parker, M.A.; King, D.G.

    1996-02-05

    Thermoplastic film added to proppants is effective and economical for preventing proppant flowback after an hydraulic fracturing treatment. Most other methods, such as resin-coated proppant and fiber, for controlling proppant flowback have drawbacks that added to treatment costs by requiring long downtime, costly additives, or frequent equipment replacement. Thermoplastic film does not react chemically with fracturing fluids. After the proppant is placed in the fracture, the film strips intertwine with the proppant grains or at higher temperatures, the strips become adhesive and shrink forming consolidated clusters that hold open the newly created fractures and prevent proppant from flowing back. The low cost of the film means that the strips can be used throughout the fracturing job or in selected stages. The strips are compatible with fracturing fluid chemistry, including breakers and crosslinkers, and can be used in wells with a wide range of bottom hole temperatures. The end result is a well that can be brought back on-line in a short time with little proppant flowback. This paper reviews the cost benefits and performance of these proppants.

  3. Membranes and Films from Polymers.

    ERIC Educational Resources Information Center

    Blumberg, Avrom A.

    1986-01-01

    Provides background information on polymeric films and membranes including production methods, special industrial and medical applications, laboratory preparation, and an experimental investigation of a porous cellulose acetate membrane. Presents a demonstration to distinguish between high- and low-density polyethylene. (JM)

  4. Pricing Films, Filmstrips and Records.

    ERIC Educational Resources Information Center

    Epstein, Connie C.

    1984-01-01

    Examines pricing practices of major producers of educational materials: Weston Woods, Listening Library, Random House Educational Media, Live Oak Media, S&S Communications Group, Phoenix/BFA, Benchmark, and Churchill Films. Royalties, production and manufacturing costs, list prices, recoveries to producers, and marketing are noted. (EJS)

  5. Hybrid thin-film amplifier

    NASA Technical Reports Server (NTRS)

    Cleveland, G.

    1977-01-01

    Miniature amplifier for bioelectronic instrumentation consumes only about 100 mW and has frequency response flat to within 0.5 dB from 0.14 to 450 Hz. Device consists of five thin film substrates, which contain eight operational amplifiers and seven field-effect transistor dice.

  6. Thin film polymeric gel electrolytes

    DOEpatents

    Derzon, D.K.; Arnold, C. Jr.; Delnick, F.M.

    1996-12-31

    Novel hybrid thin film electrolytes, based on an organonitrile solvent system, which are compositionally stable, environmentally safe, can be produced efficiently in large quantity and which, because of their high conductivities {approx_equal}10{sup {minus}3}{Omega}{sup {minus}1} cm{sup {minus}1} are useful as electrolytes for rechargeable lithium batteries. 1 fig.

  7. Oil-film-parameter investigation

    NASA Technical Reports Server (NTRS)

    Kingsbury, E. P.

    1972-01-01

    A counter rotating fixture was designed and built to measure starved EHD film thicknesses. Some good geometry glass races were obtained. A theoretical analysis of starvation was made. Measurements of retainer stability during bimode torque disturbances were made. The most common form of bimode was related to stability of retainer cock.

  8. Film Guide for Music Educators.

    ERIC Educational Resources Information Center

    Shetler, Donald J.

    The music oriented films and filmstrips in this catalog were produced for use on instructional, educational, or commercial television, or were designed to be used in a specific area and at a specific level of music teaching. Many of the listings should be of interest to teachers of general music at the secondary school level. Two indices are…

  9. Thin Film Solid Lubricant Development

    NASA Technical Reports Server (NTRS)

    Benoy, Patricia A.

    1997-01-01

    Tribological coatings for high temperature sliding applications are addressed. A sputter-deposited bilayer coating of gold and chromium is investigated as a potential solid lubricant for protection of alumina substrates during sliding at high temperature. Evaluation of the tribological properties of alumina pins sliding against thin sputtered gold films on alumina substrates is presented.

  10. Teaching Bank Runs through Films

    ERIC Educational Resources Information Center

    Flynn, David T.

    2009-01-01

    The author advocates the use of films to supplement textbook treatments of bank runs and panics in money and banking or general banking classes. Modern students, particularly those in developed countries, tend to be unfamiliar with potential fragilities of financial systems such as a lack of deposit insurance or other safety net mechanisms. Films…

  11. Buckling of polymerized monomolecular films

    NASA Astrophysics Data System (ADS)

    Bourdieu, L.; Daillant, J.; Chatenay, D.; Braslau, A.; Colson, D.

    1994-03-01

    The buckling of a two-dimensional polymer network at the air-water interface has been evidenced by grazing incidence x-ray scattering. A comprehensive description of the inhomogeneous octadecyltrichlorosilane polymerized film was obtained by atomic force microscopy and x-ray scattering measurements. The buckling occurs with a characteristic wavelength ~=10 μm.

  12. Sputtered film thermistor IR detectors

    NASA Astrophysics Data System (ADS)

    Baliga, Shankar B.; Rost, Martin R.; Doctor, Alan P.

    1994-07-01

    The thermistor infrared detector or bolometer is the detector of choice in many classical remote sensing applications such as horizon sensing, noncontact thermometry, and industrial applications. In recent years, the authors have developed a thin film process where the thermistor material is deposited from a target directly onto the substrate. This is an advance over the labor intensive ceramic technology, where sintered flakes of the thermistor are bonded to the substrate. The thin film technique permits a variety of device constructions and configurations. Detectors fabricated on heat-sunk ceramic substrates can withstand high operating temperatures and large incident optical power, in both pulsed and CW laser measurements. For dc or low frequency measurements, the films can be deposited onto a thermally isolated membrane with applications in motion sensing, gas detection, and temperature measurement. Utilizing advances in micromachining a 2D array of thermally isolated microbolometer sensors, integrated onto a silicon wafer containing readout circuitry may be achieved. This paper describes the construction of the sputtered film thermistor detectors, their operation, and applications.

  13. Adhesion of latex films. Influence of surfactants

    SciTech Connect

    Charmeau, J.Y.; Kientz, E.; Holl, Y.

    1996-12-31

    In the applications of film forming latexes in paint, paper, coating, adhesive, textile industries, one of the most important property of latex films is adhesion onto a support. From the point of view of adhesion, latex films have two specificities. The first one arises from the particular structure of the film which is usually not homogeneous but retains to a certain extent the memory of the particles it was made from. These structure effects are clearly apparent when one compares mechanical or adhesion properties of pure latex films and of films of the same polymers but prepared from a solution. Latex films show higher Young`s moduli and lower adhesion properties than solution films. The second specificity of latex films comes from the presence of the surfactant which was used in the synthesis and as stabilizer for the latex. Most industrial latexes contain low amounts of surfactant, typically in the range 0.1 to 2-3 wt%. However, being usually incompatible with the polymer, the surfactant is not homogeneously distributed in the film. It tends to segregate towards the film-air or film-support interfaces or to form domains in the bulk of the film. Distribution of surfactants in latex films has been studied by several authors. The influence of the surfactant on adhesion, as well as on other properties, is thus potentially very important. This article presents the results of the authors investigation of surfactant effects on adhesion properties of latex films. To the authors knowledge, there is no other example, in the open literature, of this kind of study.

  14. A film about teenage pregnancy.

    PubMed

    Smith, S

    1989-01-01

    "Consequences," a film on teenage pregnancy, was made in Africa with support from the Pathfinder Fund, an American foundation, International Planned Parenthood Federation, and the Ford foundation. Its messages are the repercussions of pregnancy, the use of contraception (especially condoms, as they help to stop the transmission of the acquired immunodeficiency syndrome), and the need for teenagers to communicate with their parents. The abortion issue was handled by making the points that it is illegal and dangerous. Harriet Masembe, a Ugandan folk lorist helped develop the story line. A Zimbabwean, Olley Mauma, wrote the dialogue and directed the film. Segun Oyekunle, a Nigerian script writer, commented on the draft script. The story is that Rita, a 16- year-old African is bright and has a steady boy friend. She will soon graduate from high school and go on to university. Then she discovers her pregnancy. Her relationship with Richard, her boy friend, breaks down. Her school performance deteriorates. Both Rita and Rick get expelled from school. Rita is sent to her mother's village to have a child. She finds this is very hard, and includes a lot of responsibility. She comes home a year later, but finds it difficult to relate to her friends. The boy friend suddenly returns home, too. At the end of the 54-minute film, we are left wondering what will happen to Rita and Richard. The film was pretested with 250 teenagers in Kenya, Nigeria, and Zimbabwe, and others in London and the US. The script was translated into French, Shona, and Sindebele. A Swahili version is being made. The film is being placed with nongovernmental organizations and their agencies. There has been much publicity and the film has won 2 international awards. Parts of the film were shown on German television. Distribution began in May, 1988. Since then some 300 copies and 600 videos have been sent out. There is a copy in each of the 45 agencies affiliated with International Planned Parenthood

  15. Film stacking architecture for immersion lithography process

    NASA Astrophysics Data System (ADS)

    Goto, Tomohiro; Sanada, Masakazu; Miyagi, Tadashi; Shigemori, Kazuhito; Kanaoka, Masashi; Yasuda, Shuichi; Tamada, Osamu; Asai, Masaya

    2008-03-01

    In immersion lithography process, film stacking architecture will be necessary due to film peeling. However, the architecture will restrict lithographic area within a wafer due to top side EBR accuracy In this paper, we report an effective film stacking architecture that also allows maximum lithographic area. This study used a new bevel rinse system on RF3 for all materials to make suitable film stacking on the top side bevel. This evaluation showed that the new bevel rinse system allows the maximum lithographic area and a clean wafer edge. Patterning defects were improved with suitable film stacking.

  16. Light guiding properties of soap films

    NASA Astrophysics Data System (ADS)

    Emile, Janine; Emile, Olivier; Casanova, Federico

    2013-02-01

    The injection of a laser beam from the side in a horizontal free-standing draining soap film is reported. We observe the self-deflection of the beam that varies in a random way. The film thinning is affected by the injection and depends on the polarization of the light beam, not on the laser power. The liquid in the soap film is ejected towards the meniscus, without modifying its molecular structure. Besides, this injection seems to stabilize the film near the light beam propagation and to destabilize the film in the other zones. Consequences and applications are then discussed.

  17. Reverse draining of a magnetic soap film

    NASA Astrophysics Data System (ADS)

    Moulton, D. E.; Pelesko, J. A.

    2010-04-01

    We investigate the draining of a vertical magnetic soap film in the presence of a strong, nonuniform magnetic field. A colloidal suspension of magnetic nanoparticles in a regular soap solution yields a magnetic soap solution, from which a soap film is formed across an isolated frame. Experiments demonstrate that with a strong magnet placed above the frame, the film may be made to flow upward against gravity. The amount of film draining upward is altered by varying the distance between the frame and magnet. A first mathematical model is developed for the evolution of the film. Simulations demonstrate qualitative agreement with the experiment.

  18. Specific optical rotation indicatrices of chitosan films

    NASA Astrophysics Data System (ADS)

    Rudenko, Darya A.; Shipovskaya, Anna B.

    2016-04-01

    The optical activity of chitosan films in the forms of polysalt (chitosan acetate) and polybase was studied. The specific optical rotation [α] of all our films was negative. The absolute values of [α] of polybasic chitosan films was by an order of magnitude higher than that for polysalt films. A dependence of [α] on the orientation angle of the sample relative to the direction of the polarization vector of the incident light beam in the plane perpendicular to this beam was established. Specific optical rotation indicatrices of the chitosan films of both chemical forms were plotted.

  19. Optical characterization of sputtered carbon films

    SciTech Connect

    Ager, J.W. III.

    1992-05-01

    Spattered carbon films are widely used as protective overcoats for thin film disk media. Raman spectroscopy is nondestructive and relatively rapid and is well suited for the characterization of carbon films. Specific features in the Raman spectra are empirically correlated with the rates of specific types of mechanical wear for both hydrogenated and unhydrogenated films. This observation is interpreted in terms of a random covalent network, in which the mechanical performance of the film is determined by the nature of the bonding that links sp{sup 2}-bonded domains.

  20. Electrically Conductive Polyimide Films Containing Gold Surface

    NASA Technical Reports Server (NTRS)

    Caplan, Maggie L.; Stoakley, Diane M.; St. Clair, Anne K.

    1994-01-01

    Polyimide films exhibiting high thermo-oxidative stability and including electrically conductive surface layers containing gold made by casting process. Many variations of basic process conditions, ingredients, and sequence of operations possible, and not all resulting versions of process yield electrically conductive films. Gold-containing layer formed on film surface during cure. These metallic gold-containing polyimides used in film and coating applications requiring electrical conductivity, high reflectivity, exceptional thermal stability, and/or mechanical integrity. They also find commercial potential in areas ranging from thin films for satellite antennas to decorative coatings and packaging.

  1. Carbon film electrodes for super capacitor applications

    SciTech Connect

    Tan, M.X.

    1999-11-30

    A microporous carbon film for use as electrodes in energy storage devices is disclosed, which is made by the process comprising the steps of: (1) heating a polymer film material consisting essentially of a copolymer of polyvinylidene chloride and polyvinyl chloride in an inert atmosphere to form a carbon film; and (2) activating said carbon film to form said microporous carbon film having a density between about 0.7 g/cm{sup 2} and 1 g/cm{sup 2} and a gravimetric capacitance of about between 120 F/g and 315 F/g.

  2. Carbon film electrodes for super capacitor applications

    DOEpatents

    Tan, Ming X.

    1999-01-01

    A microporous carbon film for use as electrodes in energy strorage devices is disclosed, which is made by the process comprising the steps of: (1) heating a polymer film material consisting essentially of a copolymer of polyvinylidene chloride and polyvinyl chloride in an inert atmosphere to form a carbon film; and (2) activating said carbon film to form said microporous carbon film having a density between about 0.7 g/cm.sup.2 and 1 g/cm.sup.2 and a gravimetric capacitance of about between 120 F/g and 315 F/g.

  3. Thermodynamics of boson quantum films

    SciTech Connect

    Campbell, C.E.; Clements, B.E.; Krotscheck, E. |; Saarela, M.

    1997-02-01

    Theoretical studies of films of liquid {sup 4}He adsorbed to strongly attractive plane substrates indicate that the growth of such films occurs through a sequence of first-order phase transitions {emdash} {open_quotes}layering transitions{close_quotes} {emdash} which are a direct consequence of the short-range, hard-core-like interaction between individual helium atoms. The present work examines the effects of temperature on these transitions. At given temperatures, the spinodal points and phase coexistence boundaries are determined for the transitions. Increasing the temperature tends to decrease the coverage span of the transition regions, signaling the possible existence of a critical point terminating the two-phase equilibrium. The layering transitions depend strongly on the helium-substrate potential; the longer-range helium-magnesium potential yields fewer transitions and noticeably lower transition temperatures than the helium-graphite potential. The temperature dependence of the chemical potential, third sound, static structure function, heat capacities, and superfluid densities are reported. The heat capacities are compared to those measured by Greywall and Busch [Phys Rev. Lett. {bold 67}, 3535 (1991)]. The thermal broadening of the film{close_quote}s density profile is also discussed. We find that below 1.2 K, thermal broadening is quite weak for coverages away from the layering transitions. The monolayer film experiences the least broadening whereas double-layer and triple-layer films broaden by increasing the local density in the outer tail of their density profiles, while depleting the local density in the inner portion of the outermost layer. {copyright} {ital 1997} {ital The American Physical Society}

  4. Method for fabricating hafnia films

    DOEpatents

    Hu, Michael Z [Knoxville, TN

    2007-08-21

    The present invention comprises a method for fabricating hafnia film comprising the steps of providing a substrate having a surface that allows formation of a self-assembled monolayer thereon via covalent bonding; providing an aqueous solution that provides homogeneous hafnium ionic complexes and hafnium nanoclusters wherein the aqueous solution is capable of undergoing homogeneous precipitation under controlled conditions for a desired period of time at a controlled temperature and controlled solution acidity for desired nanocluster nucleation and growth kinetics, desired nanocluster size, desired growth rate of film thickness and desired film surface characteristics. The method further comprising forming the self-assembled monolayer on the surface of the substrate wherein the self-assembled monolayer comprises a plurality of hydrocarbon chains cross-linked together along the surface of the substrate, the hydrocarbon chains being uniformly spaced from one another and wherein each of the hydrocarbon chains having a functional anchoring group at a first end of the chain covalently bonded with the surface of the substrate and each of the hydrocarbon chains having a functional terminating group projected away from the surface wherein the functional terminating group provides a bonding site for the hafnium film to grow; and exposing the substrate to the aqueous solution for a desired period of time at a controlled temperature wherein the hafnium ionic complexes and the hafnium nanoclusters are deposited on the bonding site of the functional terminating group thereby forming the hafnia film wherein the hafnium bonded to the hydrocarbons and to one another provide a uniform ordered arrangement defined by the uniform arrangement of the hydrocarbons.

  5. Rupture Limit of Thin Moving Films

    NASA Astrophysics Data System (ADS)

    Padrino, Juan C.; Joseph, Daniel D.; Kim, Hyungjun

    2010-11-01

    The rupture of a thin film in another fluid is studied including the effects of disjoining pressure. The study considers the linear stability of a moving viscous film in a motionless inviscid fluid and of a stagnant viscous film in a motionless viscous fluid. These are analyzed by means of the Navier--Stokes equations and the dissipation approximation based on potential flow. Results reveal that the dissipation method provides a good approximation for the case of a moving film, whereas its predictions are off the mark for the stagnant film case. The thickness of the gap at the trough of Kelvin-Helmholtz waves locates the formation of holes. The wavelength at final collapse is determined by the length of waves at the trough of the corrugated film. The disjoining pressure effects cause very fast break-up for very thin films. These effects influence the cutoff wavenumber. In the limit of small gaps on this corrugated film, the Reynolds and Weber numbers tend to zero with the gap size, the Ohnesorge number increases like the reciprocal of the square root and the Hamaker number like the reciprocal of the square of the gap. The motion of the film does not enter at the point of formation of holes. Moreover, for the most unstable wave, the ratio of the wavelength to film thickness is found to decrease with decreasing film thickness.

  6. Tear film measurement by optical reflectometry technique.

    PubMed

    Lu, Hui; Wang, Michael R; Wang, Jianhua; Shen, Meixiao

    2014-02-01

    Evaluation of tear film is performed by an optical reflectometer system with alignment guided by a galvanometer scanner. The reflectometer system utilizes optical fibers to deliver illumination light to the tear film and collect the film reflectance as a function of wavelength. Film thickness is determined by best fitting the reflectance-wavelength curve. The spectral reflectance acquisition time is 15 ms, fast enough for detecting film thickness changes. Fast beam alignment of 1 s is achieved by the galvanometer scanner. The reflectometer was first used to evaluate artificial tear film on a model eye with and without a contact lens. The film thickness and thinning rate have been successfully quantified with the minimum measured thickness of about 0.3 μm. Tear films in human eyes, with and without a contact lens, have also been evaluated. A high-contrast spectral reflectance signal from the precontact lens tear film is clearly observed, and the thinning dynamics have been easily recorded from 3.69 to 1.31 μm with lipid layer thickness variation in the range of 41 to 67 nm. The accuracy of the measurement is better than ±0.58% of the film thickness at an estimated tear film refractive index error of ±0.001. The fiber-based reflectometer system is compact and easy to handle.

  7. Tear film measurement by optical reflectometry technique.

    PubMed

    Lu, Hui; Wang, Michael R; Wang, Jianhua; Shen, Meixiao

    2014-02-01

    Evaluation of tear film is performed by an optical reflectometer system with alignment guided by a galvanometer scanner. The reflectometer system utilizes optical fibers to deliver illumination light to the tear film and collect the film reflectance as a function of wavelength. Film thickness is determined by best fitting the reflectance-wavelength curve. The spectral reflectance acquisition time is 15 ms, fast enough for detecting film thickness changes. Fast beam alignment of 1 s is achieved by the galvanometer scanner. The reflectometer was first used to evaluate artificial tear film on a model eye with and without a contact lens. The film thickness and thinning rate have been successfully quantified with the minimum measured thickness of about 0.3 μm. Tear films in human eyes, with and without a contact lens, have also been evaluated. A high-contrast spectral reflectance signal from the precontact lens tear film is clearly observed, and the thinning dynamics have been easily recorded from 3.69 to 1.31 μm with lipid layer thickness variation in the range of 41 to 67 nm. The accuracy of the measurement is better than ±0.58% of the film thickness at an estimated tear film refractive index error of ±0.001. The fiber-based reflectometer system is compact and easy to handle. PMID:24500519

  8. Ion beam sputter deposited diamond like films

    NASA Technical Reports Server (NTRS)

    Banks, B. A.; Rutledge, S. K.

    1982-01-01

    A single argon ion beam source was used to sputter deposit carbon films on fused silica, copper, and tantalum substrates under conditions of sputter deposition alone and sputter deposition combined with simultaneous argon ion bombardment. Simultaneously deposited and ion bombarded carbon films were prepared under conditions of carbon atom removal to arrival ratios of 0, 0.036, and 0.71. Deposition and etch rates were measured for films on fused silica substrates. Resulting characteristics of the deposited films are: electrical resistivity of densities of 2.1 gm/cu cm for sputter deposited films and 2.2 gm/cu cm for simultaneously sputter deposited and Ar ion bombarded films. For films approximately 1700 A thick deposited by either process and at 5550 A wavelength light the reflectance was 0.2, the absorptance was 0.7, the absorption coefficient was 67,000 cm to the -1 and the transmittance was 0.1.

  9. Mirrorlike pulsed laser deposited tungsten thin film

    SciTech Connect

    Mostako, A. T. T.; Khare, Alika; Rao, C. V. S.

    2011-01-15

    Mirrorlike tungsten thin films on stainless steel substrate deposited via pulsed laser deposition technique in vacuum (10{sup -5} Torr) is reported, which may find direct application as first mirror in fusion devices. The crystal structure of tungsten film is analyzed using x-ray diffraction pattern, surface morphology of the tungsten films is studied with scanning electron microscope and atomic force microscope. The film composition is identified using energy dispersive x-ray. The specular and diffuse reflectivities with respect to stainless steel substrate of the tungsten films are recorded with FTIR spectra. The thickness and the optical quality of pulsed laser deposition deposited films are tested via interferometric technique. The reflectivity is approaching about that of the bulk for the tungsten film of thickness {approx}782 nm.

  10. Mirrorlike pulsed laser deposited tungsten thin film.

    PubMed

    Mostako, A T T; Rao, C V S; Khare, Alika

    2011-01-01

    Mirrorlike tungsten thin films on stainless steel substrate deposited via pulsed laser deposition technique in vacuum (10(-5) Torr) is reported, which may find direct application as first mirror in fusion devices. The crystal structure of tungsten film is analyzed using x-ray diffraction pattern, surface morphology of the tungsten films is studied with scanning electron microscope and atomic force microscope. The film composition is identified using energy dispersive x-ray. The specular and diffuse reflectivities with respect to stainless steel substrate of the tungsten films are recorded with FTIR spectra. The thickness and the optical quality of pulsed laser deposition deposited films are tested via interferometric technique. The reflectivity is approaching about that of the bulk for the tungsten film of thickness ∼782 nm. PMID:21280810

  11. Jet impact on a soap film.

    PubMed

    Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

    2012-09-01

    We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale. PMID:23031009

  12. Infrared radiation of thin plastic films.

    NASA Technical Reports Server (NTRS)

    Tien, C. L.; Chan, C. K.; Cunnington, G. R.

    1972-01-01

    A combined analytical and experimental study is presented for infrared radiation characteristics of thin plastic films with and without a metal substrate. On the basis of the thin-film analysis, a simple analytical technique is developed for determining band-averaged optical constants of thin plastic films from spectral normal transmittance data for two different film thicknesses. Specifically, the band-averaged optical constants of polyethylene terephthalate and polyimide were obtained from transmittance measurements of films with thicknesses in the range of 0.25 to 3 mil. The spectral normal reflectance and total normal emittance of the film side of singly aluminized films are calculated by use of optical constants; the results compare favorably with measured values.

  13. Field Emission and Nanostructure of Carbon Films

    SciTech Connect

    Merkulov, V.I.; Lowndes, D.H.; Baylor, L.R.

    1999-11-29

    The results of field emission measurements of various forms of carbon films are reported. It is shown that the films nanostructure is a crucial factor determining the field emission properties. In particular, smooth, pulsed-laser deposited amorphous carbon films with both high and low sp3 contents are poor field emitters. This is similar to the results obtained for smooth nanocrystalline, sp2-bonded carbon films. In contrast, carbon films prepared by hot-filament chemical vapor deposition (HE-CVD) exhibit very good field emission properties, including low emission turn-on fields, high emission site density, and excellent durability. HF-CVD carbon films were found to be predominantly sp2-bonded. However, surface morphology studies show that these films are thoroughly nanostructured, which is believed to be responsible for their promising field emission properties.

  14. 2013 Problem 8: Jet and Film

    NASA Astrophysics Data System (ADS)

    Zeng, Pei; Chen, Lan; Zhu, Kejing

    2015-10-01

    In this article, we investigate the interaction between the water jet and soap film under different jet speeds and incident angles. We consider two different phenomena- penetrating and non-penetrating, and their corresponding conditions. In the case of penetration, we seek for the relationship between the parameters of incident jet and emergent jet, calculate the shape of the film under specific occasions. In the case of non-penetration the jet may adhere to the surface of the film or bounce off the film several times. Depending on the incident angle and velocity of the jet, the film will be found in stable and unstable patterns. We calculate the shape of the jet and the film under different conditions and found the patterns in experimental observations. Finally we portrait a `phase diagram' illustrating the conditions for different forms of jet and film interaction.

  15. Jet impact on a soap film

    NASA Astrophysics Data System (ADS)

    Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

    2012-09-01

    We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

  16. Domain Growth Kinetics in Stratifying Foam Films

    NASA Astrophysics Data System (ADS)

    Zhang, Yiran; Sharma, Vivek

    2015-03-01

    Baking bread, brewing cappuccino, pouring beer, washing dishes, shaving, shampooing, whipping eggs and blowing bubbles all involve creation of aqueous foam films. Typical foam films consist of two surfactant-laden surfaces that are μ 5 nm - 10 micron apart. Sandwiched between these interfacial layers is a fluid that drains primarily under the influence of viscous and interfacial forces, including disjoining pressure. Interestingly, for certain low molecular weight surfactants, a layered ordering of micelles inside the foam films (thickness <100 nm) leads to a stepwise thinning phenomena called stratification. We experimentally elucidate the influence of these different driving forces, and confinement on drainage kinetics of horizontal stratifying foam films. Thinner, darker domains spontaneously grow within foam films. Quantitative characterization of domain growth visualized in a using Scheludko-type thin film cell and a theoretical model based on lubrication analysis, provide critical insights into hydrodynamics of thin foam films, and the strength and nature of surface forces, including supramolecular oscillatory structural forces.

  17. Programmed degradation of DNA multilayer films.

    PubMed

    Lee, Lillian; Johnston, Angus P R; Caruso, Frank

    2014-07-23

    The design and assembly of DNA multilayer films with programmable degradation properties are reported. The nanostructured DNA films are assembled through the layer-by-layer (LbL) assembly technique and can be programmed to degrade by subsequently introducing DNA strands of specific sequences. The strands preferentially hybridize to the building blocks that stabilize the film structure, causing the film to rearrange and degrade. The rate of degradation is influenced by both the availability and accessibility of the complementary DNA binding sites within the film, as well as the degree of crosslinking within the film. Similar results are obtained for DNA multilayer films assembled on planar and particle supports. This approach offers an avenue to tailor degradability features into DNA-based materials that may find application in the biosciences, in areas such as biosensing and drug delivery. PMID:24664540

  18. Jet impact on a soap film.

    PubMed

    Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

    2012-09-01

    We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

  19. The opacity of tablet film coatings.

    PubMed

    Rowe, R C

    1984-09-01

    The opacity of tablet film coatings containing a variety of pigments and fillers has been assessed using a contrast ratio defined as the ratio of the measured reflectance of the incident light when the film is placed on a black substrate to the measured reflectance of the incident light when the film is placed on a white substrate. Films pigmented with calcium carbonate, calcium sulphate or talc had very low contrast ratios and only the inclusion of titanium dioxide imparted opacity. Films pigmented with the coloured lake pigments had contrast ratios dependent on both the parent dye and the dye concentration with the contrast ratios decreasing blue greater than red greater than orange greater than yellow. Films pigmented with the synthetic iron oxides all had very high contrast ratios. The results are consistent with the known theories of light scattering and absorption and illustrate the potential of this accurate, rapid and simple technique in the optimization of film formulations during product development.

  20. Method of making reflecting film reflector

    DOEpatents

    Cottingham, James G.

    1980-01-01

    A reflector of the reflecting film type is disclosed and which may be used in a heliostatic system for concentrating solar energy and comprising a reflecting film bonded to an appropriate rigid substrate in such a way that specularity of a very high order is achieved. A method of bonding the reflecting film to the substrate is also disclosed and comprises the steps of initially adhering the film to a smooth, clean flat rigid surface with a non-bonding liquid between the rigid surface and film, and then bonding the substrate and film. The non-bonding liquid has a molecular adhesion greater than any stresses due to handling or curing of the bonding agent which is applied between the film and the opposing surface of the rigid substrate.

  1. Zinc oxide thin film acoustic sensor

    SciTech Connect

    Mohammed, Ali Jasim; Salih, Wafaa Mahdi; Hassan, Marwa Abdul Muhsien; Nusseif, Asmaa Deiaa; Kadhum, Haider Abdullah; Mansour, Hazim Louis

    2013-12-16

    This paper reports the implementation of (750 nm) thickness of Zinc Oxide (ZnO) thin film for the piezoelectric pressure sensors. The film was prepared and deposited employing the spray pyrolysis technique. XRD results show that the growth preferred orientation is the (002) plane. A polycrystalline thin film (close to mono crystallite like) was obtained. Depending on the Scanning Electron Microscopy photogram, the film homogeneity and thickness were shown. The resonance frequency measured (about 19 kHz) and the damping coefficient was calculated and its value was found to be about (2.5538), the thin film be haves as homogeneous for under and over damped. The thin film pressure sensing was approximately exponentially related with frequency, the thin film was observed to has a good response for mechanical stresses also it is a good material for the piezoelectric properties.

  2. AES analysis of barium fluoride thin films

    NASA Astrophysics Data System (ADS)

    Kashin, G. N.; Makhnjuk, V. I.; Rumjantseva, S. M.; Shchekochihin, Ju. M.

    1993-06-01

    AES analysis of thin films of metal fluorides is a difficult problem due to charging and decomposition of such films under electron bombardment. We have developed a simple algorithm for a reliable quantitative AES analysis of metal fluoride thin films (BaF 2 in our work). The relative AES sensitivity factors for barium and fluorine were determined from BaF 2 single-crystal samples. We have investigated the dependence of composition and stability of barium fluoride films on the substrate temperature during film growth. We found that the instability of BaF 2 films grown on GaAs substrates at high temperatures (> 525°C) is due to a loss of fluorine. Our results show that, under the optimal electron exposure conditions, AES can be used for a quantitative analysis of metal fluoride thin films.

  3. Carbon Film Electrodes For Super Capacitor Applications

    DOEpatents

    Tan, Ming X.

    1999-07-20

    A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area (.apprxeq.1000 m.sup.2 /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160.degree. C. for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750.degree. C. in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750-850.degree. C. for between 1-6 hours.

  4. The Silent Film Era: Silent Films, NAD Films, and the Deaf Community's Response

    ERIC Educational Resources Information Center

    Schuchman, John S.

    2004-01-01

    Older citizens who are deaf or hard of hearing recall the years of silent films (1893-1929) as a "golden era" in the cultural history of the American Deaf community. It was golden for several reasons. First, this period represents the one brief time that deaf and hard of hearing citizens had comparatively equal access to motion pictures--a…

  5. Microstructure Related Properties of Optical Thin Films.

    NASA Astrophysics Data System (ADS)

    Wharton, John James, Jr.

    Both the optical and physical properties of thin film optical interference coatings depend upon the microstructure of the deposited films. This microstructure is strongly columnar with voids between the columns. Computer simulations of the film growth process indicate that the two most important factors responsible for this columnar growth are a limited mobility of the condensing molecules and self-shadowing by molecules already deposited. During the vacuum deposition of thin films, the microstructure can be influenced by many parameters, such as substrate temperature and vacuum pressure. By controlling these parameters and introducing additional ones, thin film coatings can be improved. In this research, ultraviolet irradiation and ion bombardment were examined as additional parameters. Past studies have shown that post-deposition ultraviolet irradiation can be used to relieve stress and reduce absorption in the far ultraviolet of silicon dioxide films. Ion bombardment has been used to reduce stress, improve packing density, and increase resistance to moisture penetration. Three refractory oxide materials commonly used in thin film coatings were studied; they are silicon dioxide, titanium dioxide, and zirconium dioxide. Both single-layer films and narrowband filters made of these materials were examined. A 1000-watt mercury-xenon lamp was used to provide ultraviolet irradiation. An inverted magnetron ion source was used to produce argon and oxygen ions. Ultraviolet irradiation was found to reduce the absorption and slightly increase the index of refraction in zirconium oxide films. X-ray diffraction analysis revealed that ultraviolet irradiation caused titanium oxide films to become more amorphous; their absorption in the ultraviolet was slightly reduced. No changes were noted in film durability. Ion bombardment enhanced the tetragonal (lll) peak of zirconium oxide but increased the absorption of both zirconium oxide and titanium oxide films. The titanium oxide

  6. Epitaxial film transfer technique for producing single crystal Si film on an insulating substrate

    NASA Astrophysics Data System (ADS)

    Kimura, M.; Egami, K.; Kanamori, M.; Hamaguchi, T.

    1983-08-01

    Epitaxial film transfer, a new technique for producing a single crystal Si film with both large size and high quality on an insulating substrate, is demonstrated. The technique in which an epitaxial Si film is transferred to a secondary substrate by using three fundamental processes of epitaxial growth, bonding of two wafers, and substrate elimination, can produce a 2-in. single crystal Si film as thin as 1.5 μm on a insulating substrate. Thickness variation can be controlled to ±0.06 μm across a 2-in. wafer. An epitaxial Si film is transferred without significant degradation in quality although a fine film waving exists.

  7. Homoepitaxial ZnO Film Growth

    NASA Technical Reports Server (NTRS)

    Zhu, Shen; Su, C-H; Lehoczky, S. L.; Harris, M. T.; Callahan, M. J.; McCarty, P.; George, M. A.; Rose, M. Franklin (Technical Monitor)

    2000-01-01

    ZnO films have high potential for many applications, such as surface acoustic wave filters, UV detectors, and light emitting devices due to its structural, electrical, and optical properties. High quality epitaxial films are required for these applications. The Al2O3 substrate is commonly used for ZnO heteroepitaxial growth. Recently, high quality ZnO single crystals are available for grow homoepitaxial films. Epitaxial ZnO films were grown on the two polar surfaces (O-face and Zn-face) of (0001) ZnO single crystal substrates using off-axis magnetron sputtering deposition. As a comparison, films were also deposited on (0001) Al2O3 substrates. It was found that the two polar ZnO surfaces have different photoluminescence (PL) spectrum, surface structure and morphology, which strongly influence the epitaxial film growth. The morphology and structure of homoepitaxial films grown on the ZnO substrates were different from heteroepitaxial films grown on the Al2O3. An interesting result shows that high temperature annealing of ZnO single crystals will improve the surface structure on the O-face surface rather than the opposite surface. The measurements of PL, low-angle incident x-ray diffraction, and atomic force microscopy of ZnO films indicate that the O-terminated surface is better for ZnO epitaxial film growth.

  8. Biodegradable lignin/polyolefin composite films

    SciTech Connect

    Kosikova, B.; Demjanova, V.; Mikulasova, M.; Lora, J.H.

    1993-12-31

    From the view point of environmental protection, the plastic wastes, especially from packing materials, represent a potential waste problem. Various approaches were examined to develop partially or completely biodegradable plastics. New type of partially biodegradable polyolefins was prepared by blending of polypropylene with lignin, which was recovered in the ALCELL process, an organosolv pulping process that uses ethanol-water as the delignifying agent. Films of blends with up to 10% wt ALCELL lignin, prepared in absence of commercial stabilizers, had acceptable mechanical strengths. The effect of lignin on biodegradability of the composite films was examined by comparison of behaviour of both pure and lignin containing films during treatment with fungus Phanerochaete chrysosporium. It was found that this fungus is able to grow and to produce lignolytic enzymes in the presence of the films containing lignin. Biodegradation of lignin in the composite film was confirmed by the releasing of lignin fragments into the extracellular fluid. Because of measurement of mechanical properties offers a mean of direct estimation of polymer degradation, the degree of biodegradation of the films tested was followed by monitoring of elongation at break. The changes of break at elongation in the course of enzymatic treatment revealed that the lignin/PP composite films are potentially environmentally nonpersisting. The micrographs of the lignin containing films obtained by scanning electron microscopy show the significant changes of the film surface upon degradation with Phanerochaete chrysosporium in contrast to unchanged lignin free film.

  9. CVD diamond film oxidation resistance research

    NASA Astrophysics Data System (ADS)

    Jing, Longwei; Wang, Xiaoping; Wang, Lijun; Pan, Xiufang; Sun, Yiqing; Wang, Jinye; Sun, Hongtao

    2013-12-01

    Diamond films were deposited on a silicon substrate by microwave plasma chemical vapor deposition system, and its oxidation experiments were carried out in atmospheric environmental condition by using a muffle furnace. Inatmospheric environment (the temperature is from 400°C to 900°C) the oxidation resistance of diamond thin films was investigated. The results indicate that under the atmospheric environment diamond thin film surface morphology did not change after 6 hours at 400°C. Diamond thin film surface morphology began to change after 2 hours at 600°C, and when time was extended to 4 hours, the diamond thin film surface morphology changed significantly. The surface morphology of diamond films began to change after 15 minutes at a 700°C condition and when time was extended to 6 hours diamond films were all destroyed. All the diamond films on the silicon substrate disappeared completely in 20 minutes at 900°C. The intact crystal face is the reason that natural diamond has stable chemical property. The crystal face of synthetic diamond film has a lot of defects, especially on the side. Oxidation of the diamond films begin with the grain boundary and defects.

  10. Flexible thin film magnetoimpedance sensors

    NASA Astrophysics Data System (ADS)

    Kurlyandskaya, G. V.; Fernández, E.; Svalov, A.; Burgoa Beitia, A.; García-Arribas, A.; Larrañaga, A.

    2016-10-01

    Magnetically soft thin film deposited onto polymer substrates is an attractive option for flexible electronics including magnetoimpedance (MI) applications. MI FeNi/Ti based thin film sensitive elements were designed and prepared using the sputtering technique by deposition onto rigid and flexible substrates at different deposition rates. Their structure, magnetic properties and MI were comparatively analyzed. The main structural features were sufficiently accurately reproduced in the case of deposition onto cyclo olefine polymer substrates compared to glass substrates for the same conditions. Although for the best condition (28 nm/min rate) of the deposition onto polymer a significant reduction of the MI field sensitivity was found satisfactory for sensor applications sensitivity: 45%/Oe was obtained for a frequency of 60 MHz.

  11. Thin film concentrator panel development

    NASA Technical Reports Server (NTRS)

    Zimmerman, D. K.

    1982-01-01

    The development and testing of a rigid panel concept that utilizes a thin film reflective surface for application to a low-cost point-focusing solar concentrator is discussed. It is shown that a thin film reflective surface is acceptable for use on solar concentrators, including 1500 F applications. Additionally, it is shown that a formed steel sheet substrate is a good choice for concentrator panels. The panel has good optical properties, acceptable forming tolerances, environmentally resistant substrate and stiffeners, and adaptability to low to mass production rates. Computer simulations of the concentrator optics were run using the selected reflector panel design. Experimentally determined values for reflector surface specularity and reflectivity along with dimensional data were used in the analysis. The simulations provided intercept factor and net energy into the aperture as a function of aperture size for different surface errors and pointing errors. Point source and Sun source optical tests were also performed.

  12. Silicon film solar cell process

    NASA Technical Reports Server (NTRS)

    Hall, R. B.; Mcneely, J. B.; Barnett, A. M.

    1984-01-01

    The most promising way to reduce the cost of silicon in solar cells while still maintaining performance is to utilize thin films (10 to 20 microns thick) of crystalline silicon. The method of solution growth is being employed to grow thin polycrystalline films of silicon on dissimilar substrates. The initial results indicate that, using tin as the solvent, this growth process only requires operating temperatures in the range of 800 C to 1000 C. Growth rates in the range of 0.4 to 2.0 microns per minute and grain sizes in the range of 20 to 100 microns were achieved on both quartz and coated steel substrates. Typically, an aspect ratio of two to three between the width and the Si grain thickness is seen. Uniform coverage of Si growth on quartz over a 2.5 x 2.5 cm area was observed.

  13. [The film library of Sandoz].

    PubMed

    Lefebvre, Thierry

    2014-10-01

    During nearly forty years, the Cinémathèque Sandoz helped the initial formation of students and the training of doctors and pharmacists. Half a century after the produc tion of one of his most memorable films, Le Horla (Jean-Daniel Pollet), the author provides a brief history of those cultural sponsorship activites. It presents the main leaders of the cinémathèque et some of its iconic projets. PMID:25671985

  14. [The film library of Sandoz].

    PubMed

    Lefebvre, Thierry

    2014-10-01

    During nearly forty years, the Cinémathèque Sandoz helped the initial formation of students and the training of doctors and pharmacists. Half a century after the produc tion of one of his most memorable films, Le Horla (Jean-Daniel Pollet), the author provides a brief history of those cultural sponsorship activites. It presents the main leaders of the cinémathèque et some of its iconic projets.

  15. Charge transfer in zirconium films

    NASA Astrophysics Data System (ADS)

    Mel'Nichuk, B. L.; Stasyuk, Z. V.

    1991-12-01

    In superhigh-vacuum conditions (residual gas pressure less than 10-8 Pa), electro-conductive dimensional phenomena, the Hall constant, and the absolute differential thermoemf of zirconium films are investigated. The experimental results are analyzed within the framework of current model concepts regarding volume, surface, and grain-boundary scattering of charge carriers (the Mayadas-Schatzkes and Tel'e-Tosser-Pichard models). The charge-transfer parameters in zirconium are determined.

  16. Thin film diamond microstructure applications

    NASA Technical Reports Server (NTRS)

    Roppel, T.; Ellis, C.; Ramesham, R.; Jaworske, D.; Baginski, M. E.; Lee, S. Y.

    1991-01-01

    Selective deposition and abrasion, as well as etching in atomic oxygen or reduced-pressure air, have been used to prepare patterned polycrystalline diamond films which, on further processing by anisotropic Si etching, yield the microstructures of such devices as flow sensors and accelerometers. Both types of sensor have been experimentally tested in the respective functions of hot-wire anemometer and both single- and double-hinged accelerometer.

  17. Photothermoplastic films for holographic recording

    NASA Technical Reports Server (NTRS)

    Neduzhiy, S. A.; Pavlov, A. V.; Tabatadze, D. G.; Cheltsova, T. V.

    1987-01-01

    The electrophotographic and sensitometric characteristics of poly-N-vinyl carbazole photothermoplastic films, sensitized by an amorphous-Se sublayer are examined. It is shown that the photosensitivity of the material can be improved and its spectral range can be expanded by sensitization of amorphous Se with additions of Te, As, and Sb; this can be accomplished without a significant reduction in diffraction efficiency and resolving power.

  18. Photopatternable sorbent and functionalized films

    DOEpatents

    Grate, Jay W.; Nelson, David A.

    2006-01-31

    A composition containing a polymer, a crosslinker and a photo-activatable catalyst is placed on a substrate. The composition is exposed to a predetermined pattern of light, leaving an unexposed region. The light causes the polymer to become crosslinked by hydrosilylation. A solvent is used to remove the unexposed composition from the substrate, leaving the exposed pattern to become a sorbent polymer film that will absorb a predetermined chemical species when exposed to such chemical species.

  19. Thin-Film Power Transformers

    NASA Technical Reports Server (NTRS)

    Katti, Romney R.

    1995-01-01

    Transformer core made of thin layers of insulating material interspersed with thin layers of ferromagnetic material. Flux-linking conductors made of thinner nonferromagnetic-conductor/insulator multilayers wrapped around core. Transformers have geometric features finer than those of transformers made in customary way by machining and mechanical pressing. In addition, some thin-film materials exhibit magnetic-flux-carrying capabilities superior to those of customary bulk transformer materials. Suitable for low-cost, high-yield mass production.

  20. Film and membrane-model thermodynamics of free thin liquid films.

    PubMed

    Radke, C J

    2015-07-01

    In spite of over 7 decades of effort, the thermodynamics of thin free liquid films (as in emulsions and foams) lacks clarity. Following a brief review of the meaning and measurement of thin-film forces (i.e., conjoining/disjoining pressures), we offer a consistent analysis of thin-film thermodynamics. By carefully defining film reversible work, two distinct thermodynamic formalisms emerge: a film model with two zero-volume membranes each of film tension γ(f) and a membrane model with a single zero-volume membrane of membrane tension 2γ(m). In both models, detailed thermodynamic analysis gives rise to thin-film Gibbs adsorption equations that allow calculation of film and membrane tensions from measurements of disjoining-pressure isotherms. A modified Young-Laplace equation arises in the film model to calculate film-thickness profiles from the film center to the surrounding bulk meniscus. No corresponding relation exists in the membrane model. Illustrative calculations of disjoining-pressure isotherms for water are presented using square-gradient theory. We report considerable deviations from Hamaker theory for films less than about 3 nm in thickness. Such thin films are considerably more attractive than in classical Hamaker theory. Available molecular simulations reinforce this finding. PMID:25648681

  1. Spin waves of ferromagnetic films

    NASA Astrophysics Data System (ADS)

    Arias, Rodrigo

    The spin wave modes of ferromagnetic films have been studied for a long time experimentally as well as theoretically: initially magnetostatic and later dipole-exchange modes. Theoretically dipole-exchange modes have been solved exactly numerically for some configurations and boundary conditions, and there are approximations of their frequency dispersion relations based on infinite series solutions and perturbation theory, valid for arbitrary orientations of an applied magnetic field, and for boundary conditions that allow varying degrees of pinning. A theoretical method that allows to determine with ease the exact frequency dispersion relations of the dipole-exchange modes is presented: it is required to solve numerically a 6x6 linear eigenvalue problem at each wavevector of interest; the spin wave modes inside or outside the sample may be plotted. Analogous calculations may be done to determine magnetostatic modes in detail. The method corresponds to a generalization of Green's theorem to the problem of determining the dipole-exchange modes of a ferromagnetic film: convolution integral equations for the magnetization and magnetostatic potential are derived on the surfaces of the film that become simple local algebraic equations in Fourier space, or for specific wavevectors. This work was supported by Project ICM FP10-061-F-FIC, Chile, and Center for the Development of Nanoscience and Nanotechnology CEDENNA FB0807 (Chile).

  2. Deposited films with improved microstructures

    DOEpatents

    Patten, James W.; Moss, Ronald W.; McClanahan, Edwin D.

    1984-01-01

    Methods for improving microstructures of line-of-sight deposited films are described. Columnar growth defects ordinarily produced by geometrical shadowing during deposition of such films are eliminated without resorting to post-deposition thermal or mechanical treatments. The native, as-deposited coating qualities, including homogeneity, fine grain size, and high coating-to-substrate adherence, can thus be retained. The preferred method includes the steps of emitting material from a source toward a substrate to deposit a coating non-uniformly on the substrate surface, removing a portion of the coating uniformly over the surface, again depositing material onto the surface, but from a different direction, and repeating the foregoing steps. The quality of line-of-sight deposited films such as those produced by sputtering, progressively deteriorates as the angle of incidence between the flux and the surface becomes increasingly acute. Depositing non-uniformly, so that the coating becomes progressively thinner as quality deteriorates, followed by uniformly removing some of the coating, such as by resputtering, eliminates the poor quality portions, leaving only high quality portions of the coating. Subsequently sputtering from a different direction applies a high quality coating to other regions of the surface. Such steps can be performed either simultaneously or sequentially to apply coatings of a uniformly high quality, closed microstructure to three-dimensional or large planar surfaces.

  3. Alternate capacitor dielectric film materials

    SciTech Connect

    Foster, J.C.

    1990-08-01

    New high-temperature, high-energy density, and high-radiation tolerant capacitor applications require the evaluation of alternate dielectric materials. Evaluation work was performed at GE Neutron Devices (GEND) and Sandia National Laboratories (SNL), Albuquerque. US Department of Energy (DOE) requirements for capacitor function and environments are unique, and the representations included in this report do not constitute an endorsement of any material or manufacturer. This report presents data on polymeric dielectric films evaluated to support the design of new high-energy density capacitors. Materials which were evaluated include polycarbonate (two sources), polyphenylene sulfide, polyvinylidene fluoride, polyetherimide (three sources), polyimide (four sources), polyethersulfone, and polyetherether ketone. A polyester was evaluated as the control material since many prior designs utilized this dielectric. The film evaluations were based on dielectric constant and dissipation factor variation as a function of temperature ({minus}55{degree}C to 300{degree}C) as well as dielectric breakdown strength. Additionally, film/foil capacitors in a dry wrap-and-fill configuration were fabricated and tested to determine insulation resistance, breakdown voltage, and radiation hardness. Results are given for all evaluations. 7 refs., 4 figs., 4 tabs.

  4. 8mm Film in Education: Status and Prospects--1968.

    ERIC Educational Resources Information Center

    Forsdale, Louis

    An overwhelming deterrent to the use of film in the classroom has been the inaccessibility of the films and the complicated projectors required to show them. Eight-millimeter film has the potential to lower the cost of films, making them more accessible, and to make showing them vastly simpler. This paper traces the development of 8mm film use in…

  5. Combined Film Catalog, 1972, United States Atomic Energy Commission.

    ERIC Educational Resources Information Center

    Atomic Energy Commission, Washington, DC.

    A comprehensive listing of all current United States Atomic Energy Commission (USAEC) films, this catalog describes 232 films in two major film collections. Part One: Education-Information contains 17 subject categories and two series and describes 134 films with indicated understanding levels on each film for use by schools. The categories…

  6. Thoughts on Film: Critically Engaging with Both Adorno and Benjamin

    ERIC Educational Resources Information Center

    D'Olimpio, Laura

    2015-01-01

    There is a traditional debate in analytic aesthetics that surrounds the classification of film as Art. While much philosophy devoted to considering film has now moved beyond this debate and accepts film as a mass art, a subcategory of Art proper, it is worth reconsidering the criticism of film pre-Deleuze. Much of the criticism of film as…

  7. Resources for Legal Issues in Educational Film Archives.

    ERIC Educational Resources Information Center

    Day, Martha

    2002-01-01

    Documents the different steps and strategies needed to legally archive and preserve educational film and media prints. Addresses archiving a film and creating a derivative, circulating copy; determining out-of-print titles; determining if a film is unique or an orphan film; and determining if a film is in the public domain. (Author/LRW)

  8. Nanostructural characterization of amorphous diamondlike carbon films

    SciTech Connect

    SIEGAL,MICHAEL P.; TALLANT,DAVID R.; MARTINEZ-MIRANDA,L.J.; BARBOUR,J. CHARLES; SIMPSON,REGINA L.; OVERMYER,DONALD L.

    2000-01-27

    Nanostructural characterization of amorphous diamondlike carbon (a-C) films grown on silicon using pulsed-laser deposition (PLD) is correlated to both growth energetic and film thickness. Raman spectroscopy and x-ray reflectivity probe both the topological nature of 3- and 4-fold coordinated carbon atom bonding and the topographical clustering of their distributions within a given film. In general, increasing the energetic of PLD growth results in films becoming more ``diamondlike'', i.e. increasing mass density and decreasing optical absorbance. However, these same properties decrease appreciably with thickness. The topology of carbon atom bonding is different for material near the substrate interface compared to material within the bulk portion of an a-C film. A simple model balancing the energy of residual stress and the free energies of resulting carbon topologies is proposed to provide an explanation of the evolution of topographical bonding clusters in a growing a-C film.

  9. Thin film oxygen partial pressure sensor

    NASA Technical Reports Server (NTRS)

    Wortman, J. J.; Harrison, J. W.; Honbarrier, H. L.; Yen, J.

    1972-01-01

    The development is described of a laboratory model oxygen partial pressure sensor using a sputtered zinc oxide thin film. The film is operated at about 400 C through the use of a miniature silicon bar. Because of the unique resistance versus temperature relation of the silicon bar, control of the operational temperature is achieved by controlling the resistance. A circuit for accomplishing this is described. The response of sputtered zinc oxide films of various thicknesses to oxygen, nitrogen, argon, carbon dioxide, and water vapor caused a change in the film resistance. Over a large range, film conductance varied approximately as the square root of the oxygen partial pressure. The presence of water vapor in the gas stream caused a shift in the film conductance at a given oxygen partial pressure. A theoretical model is presented to explain the characteristic features of the zinc oxide response to oxygen.

  10. Shear alignment of confined hydrocarbon liquid films.

    PubMed

    Drummond, Carlos; Alcantar, Norma; Israelachvili, Jacob

    2002-07-01

    Shear-induced structural reordering in thin liquid films of the linear saturated alkane n-eicosane (C20H42) was investigated using a surface forces apparatus and freeze-fracture (atomic force) microscopy (AFM). By rapidly freezing a shearing film followed by splitting (cleaving) the films from the confining mica substrate surfaces, it was possible to obtain AFM images of the structures of the films during steady-state sliding, revealing striped domains approximately 2 A in height and a few nanometer wide whose structure depends on the sliding velocity and, most likely, also on the sliding distance and time. In contrast, confined but unsheared films yielded completely featureless images. To the best of our knowledge, the results are the first direct experimental measurement of shear-induced ordering in nano-confined films resulting in layering and domain formation, but any molecular-level alignment, if present, could not be established. PMID:12241373

  11. Stability of Intershaft Squeeze Film Dampers

    NASA Technical Reports Server (NTRS)

    El-Shafei, A.

    1991-01-01

    Intershaft squeeze film dampers were investigated for damping of dual rotor aircraft jet engines. It was thought that the intershaft damper would enhance the stability of the rotor-bearing system. Unfortunately, it was determined that the intershaft squeeze film damper was unstable above the engine's first critical speed. Here, a stability analysis of rotors incorporating intershaft squeeze film dampers is discussed. A rotor model consisting of two Jeffcott rotors with two intershaft squeeze film dampers was investigated. Examining the system characteristic equation for the conditions at which the roots indicate an ever-growing unstable motion results in the stability conditions. The cause of the instability is identified as the rotation of the oil in the damper clearance. Several proposed configurations of intershaft squeeze film dampers are discussed, and it is shown that the intershaft dampers are stable supercritically only with a configuration in which the oil film does not rotate.

  12. Thermal property of transparent silver nanowire films

    NASA Astrophysics Data System (ADS)

    Park, J. W.; Shin, D. K.; Ahn, J.; Lee, J. Y.

    2014-01-01

    Through a comparison with transparent polymer composite films, we investigate the thermal property of transparent silver nanowire (AgNW) films that may be employed for heat sink in transparent electronic devices. To fabricate transparent polymer composite films and enhance their thermal property, poly(methyl methacrylate) (PMMA) solution featuring high transparency (∼90%) and thermal emissivity (0.9) is mixed with thermal conductive fillers such as aluminum nitride (AlN) and silicon carbide (SiC). It is observed that the thermal emissivity of the AgNW films is decreased as the sheet resistance is reduced. However, we have found that the AgNW film shows the most excellent heat dissipation property (53.7 °C) while maintaining relatively higher transparency (77.1% at 520 nm), followed by the PMMA:SiC and then PMMA:AlN films.

  13. Soap Films Burst Like Flapping Flags

    NASA Astrophysics Data System (ADS)

    Lhuissier, Henri; Villermaux, Emmanuel

    2009-07-01

    When punctured, a flat soap film bursts by opening a hole driven by liquid surface tension. The hole rim does not, however, remain smooth but soon develops indentations at the tip of which ligaments form, ultimately breaking and leaving the initially connex film into a mist of disjointed drops. We report on original observations showing that these indentations result from a flaglike instability between the film and the surrounding atmosphere inducing an oscillatory motion out of its plane. Just like a flag edge flaps in the wind, the film is successively accelerated on both sides perpendicularly to its plane, inducing film thickness modulations and centrifuging liquid ligaments that finally pinch off to form the observed spray. This effect exemplifies how the dynamics of fragile objects such as thin liquid films is sensitive to their embedding medium.

  14. Induced electronic anisotropy in bismuth thin films

    SciTech Connect

    Liao, Albert D.; Yao, Mengliang; Opeil, Cyril; Katmis, Ferhat; Moodera, Jagadeesh S.; Li, Mingda; Tang, Shuang; Dresselhaus, Mildred S.

    2014-08-11

    We use magneto-resistance measurements to investigate the effect of texturing in polycrystalline bismuth thin films. Electrical current in bismuth films with texturing such that all grains are oriented with the trigonal axis normal to the film plane is found to flow in an isotropic manner. By contrast, bismuth films with no texture such that not all grains have the same crystallographic orientation exhibit anisotropic current flow, giving rise to preferential current flow pathways in each grain depending on its orientation. Extraction of the mobility and the phase coherence length in both types of films indicates that carrier scattering is not responsible for the observed anisotropic conduction. Evidence from control experiments on antimony thin films suggests that the anisotropy is a result of bismuth's large electron effective mass anisotropy.

  15. Domain epitaxy for thin film growth

    DOEpatents

    Narayan, Jagdish

    2005-10-18

    A method of forming an epitaxial film on a substrate includes growing an initial layer of a film on a substrate at a temperature T.sub.growth, said initial layer having a thickness h and annealing the initial layer of the film at a temperature T.sub.anneal, thereby relaxing the initial layer, wherein said thickness h of the initial layer of the film is greater than a critical thickness h.sub.c. The method further includes growing additional layers of the epitaxial film on the initial layer subsequent to annealing. In some embodiments, the method further includes growing a layer of the film that includes at least one amorphous island.

  16. Tuneable dielectric films having low electrical losses

    DOEpatents

    Dimos, Duane Brian; Schwartz, Robert William; Raymond, Mark Victor; Al-Shareef, Husam Niman; Mueller, Carl; Galt, David

    2000-01-01

    The present invention is directed to a method for forming dielectric thin films having substantially reduced electrical losses at microwave and millimeter wave frequencies relative to conventional dielectric thin films. The reduction in losses is realized by dramatically increasing the grain sizes of the dielectric films, thereby minimizing intergranular scattering of the microwave signal due to grain boundaries and point defects. The increase in grain size is realized by heating the film to a temperature at which the grains experience regrowth. The grain size of the films can be further increased by first depositing the films with an excess of one of the compoents, such that a highly mobile grain boundary phase is formed.

  17. Method for forming porous platinum films

    DOEpatents

    Maya, Leon

    2000-01-01

    A method for forming a platinum film includes providing a substrate, sputtering a crystalline platinum oxide layer over at least a portion of the substrate, and reducing the crystalline platinum oxide layer to form the platinum film. A device includes a non-conductive substrate and a platinum layer having a density of between about 2 and 5 g/cm.sup.3 formed over at least a portion of the non-conductive substrate. The platinum films produced in accordance with the present invention provide porous films suitable for use as electrodes, yet require few processing steps. Thus, such films are less costly. Such films may be formed on both conductive and non-conductive substrates. While the invention has been illustrated with platinum, other metals, such as noble metals, that form a low density oxide when reactively sputtered may also be used.

  18. Deformation of an asymmetric thin film

    NASA Astrophysics Data System (ADS)

    Geng, Jun; Selinger, Jonathan V.

    2012-09-01

    Experiments have investigated shape changes of polymer films induced by asymmetric swelling by a chemical vapor. Inspired by recent work on the shaping of elastic sheets by non-Euclidean metrics [Y. Klein, E. Efrati, and E. Sharon, ScienceSCIEAS0036-807510.1126/science.1135994 315, 1116 (2007)], we represent the effect of chemical vapors by a change in the target metric tensor. In this problem, unlike that earlier work, the target metric is asymmetric between the two sides of the film. Changing this metric induces a curvature of the film, which may curve into a partial cylinder or a partial sphere. We calculate the elastic energy for each of these shapes and show that the sphere is favored for films smaller than a critical size, which depends on the film thickness, while the cylinder is favored for larger films.

  19. Iron borate films: Synthesis and characterization

    NASA Astrophysics Data System (ADS)

    Yagupov, S.; Strugatsky, M.; Seleznyova, K.; Mogilenec, Yu.; Milyukova, E.; Maksimova, E.; Nauhatsky, I.; Drovosekov, A.; Kreines, N.; Kliava, J.

    2016-11-01

    We report the first successful synthesis of iron borate films. FeBO3 films on GaBO3 single crystal substrates have been prepared by a liquid phase epitaxy route. In order to determine optimal crystallization regimes, a series of experiments has been carried out. Electron microscope studies have allowed monitoring different phases of the film formation. The compositions of the film and of the substrate have been determined by energy-dispersive spectroscopy. X-ray diffraction analysis has allowed an accurate determination of a mismatch between the lattice parameters of the film and of the substrate. Electron magnetic resonance studies of the FeBO3 film confirm the existence of magnetic ordering. The values of the effective Dzyaloshinskii field as well as the Néel temperature are in good accordance with those previously determined for FeBO3 single crystal.

  20. Dry lubricant films for aluminum forming.

    SciTech Connect

    Wei, J.; Erdemir, A.; Fenske, G. R.

    1999-03-30

    During metal forming process, lubricants are crucial to prevent direct contact, adhesion, transfer and scuffing of workpiece materials and tools. Boric acid films can be firmly adhered to the clean aluminum surfaces by spraying their methanol solutions and provide extremely low friction coefficient (about 0.04). The cohesion strengths of the bonded films vary with the types of aluminum alloys (6061, 6111 and 5754). The sheet metal forming tests indicate that boric acid films and the combined films of boric acid and mineral oil can create larger strains than the commercial liquid and solid lubricants, showing that they possess excellent lubricities for aluminum forming. SEM analyses indicate that boric acid dry films separate the workpiece and die materials, and prevent their direct contact and preserve their surface qualities. Since boric acid is non-toxic and easily removed by water, it can be expected that boric acid films are environmentally friendly, cost effective and very efficient lubricants for sheet aluminum cold forming.

  1. Fluorescent Bioactive Corrole Grafted-Chitosan Films.

    PubMed

    Barata, Joana F B; Pinto, Ricardo J B; Vaz Serra, Vanda I R C; Silvestre, Armando J D; Trindade, Tito; Neves, Maria Graça P M S; Cavaleiro, José A S; Daina, Sara; Sadocco, Patrizia; Freire, Carmen S R

    2016-04-11

    Transparent corrole grafted-chitosan films were prepared by chemical modification of chitosan with a corrole macrocycle, namely, 5,10,15-tris(pentafluorophenyl)corrole (TPFC), followed by solvent casting. The obtained films were characterized in terms of absorption spectra (UV-vis), FLIM (fluorescence lifetime imaging microscopy), structure (FTIR, XPS), thermal stability (TGA), thermomechanical properties (DMA), and antibacterial activity. The results showed that the chemical grafting of chitosan with corrole units did not affect its film-forming ability and that the grafting yield increased with the reaction time. The obtained transparent films presented fluorescence which increases with the amount of grafted corrole units. Additionally, all films showed bacteriostatic effect against S. aureus, as well as good thermomechanical properties and thermal stability. Considering these features, promising applications may be envisaged for these corrole-chitosan films, such as biosensors, bioimaging agents, and bioactive optical devices.

  2. Moisture absorption in thin polymer films

    NASA Astrophysics Data System (ADS)

    Soles, Christopher; Lenhart, Joseph; Jones, Ronnie; Prabhu, Vivek; Lin, Eric; Wu, Wen-Li

    2003-03-01

    We explore the kinetics and dynamics of moisture transport in a series of poly(hydroxystyrene), poly(tert-butoxycarboxystyrene), and epoxy films as a function of film thickness. Specular X-ray reflectivity is used to monitor the equilibrium swelling in films exposed to water vapor while a quartz crystal microbalance is used to track the kinetics of the absorption process. For relatively thick films we find that the equilibrium swelling is nominally consistent with the bulk moisture absorption properties of the polymer. However, when the film thickness drops below 100 nm, enhanced swelling occurs and the extent of the enhancement increases with resin polarity. Below the same thickness threshold of 100 nm, we also observe a strong retardation in the uptake kinetics, i.e., a decrease in the effective diffusion coefficient of the water. The results are discussed in detail with respect to confinement of the polymer films.

  3. Adhesion and friction of thin metal films

    NASA Technical Reports Server (NTRS)

    Buckley, D. H.

    1976-01-01

    Sliding friction experiments were conducted in vacuum with thin films of titanium, chromium, iron, and platinum sputter deposited on quartz or mica substrates. A single crystal hemispherically tipped gold slider was used in contact with the films at loads of 1.0 to 30.0 and at a sliding velocity of 0.7 mm/min at 23 C. Test results indicate that the friction coefficient is dependent on the adhesion of two interfaces, that between the film and its substrate and the slider and the film. There exists a relationship between the percent d bond character of metals in bulk and in thin film form and the friction coefficient. Oxygen can increase adhesive bonding of a metal film (platinum) to a substrate.

  4. Raman characterization of platinum diselenide thin films

    NASA Astrophysics Data System (ADS)

    O'Brien, Maria; McEvoy, Niall; Motta, Carlo; Zheng, Jian-Yao; Berner, Nina C.; Kotakoski, Jani; Elibol, Kenan; Pennycook, Timothy J.; Meyer, Jannik C.; Yim, Chanyoung; Abid, Mohamed; Hallam, Toby; Donegan, John F.; Sanvito, Stefano; Duesberg, Georg S.

    2016-06-01

    Platinum diselenide (PtSe2) is a newly discovered 2D material which is of great interest for applications in electronics and catalysis. PtSe2 films were synthesized by thermally assisted selenization of predeposited platinum films and scanning transmission electron microscopy revealed the crystal structure of these films to be 1T. Raman scattering of these films was studied as a function of film thickness, laser wavelength and laser polarization. E g and A 1g Raman active modes were identified using polarization measurements in the Raman setup. These modes were found to display a clear position and intensity dependence with film thickness, for multiple excitation wavelengths, and their peak positions agree with simulated phonon dispersion curves for PtSe2. These results highlight the practicality of using Raman spectroscopy as a prime characterization technique for newly synthesized 2D materials.

  5. Feasibility demonstration for electroplating ultra-thin polyimide film. [fabricating film for space erectable structures

    NASA Technical Reports Server (NTRS)

    Schneier, R.; Braswell, T. V.; Vaughn, R. W.

    1978-01-01

    The effect of electrodeposition variables on film thickness was investigated using a dilute polyimide solution as a bath into which aluminum (as foil or as a vapor deposited coating) was immersed. The electrodeposited film was dried for 2 hours at 93 C (primarily to remove solvent) and cured for 18 hours at 186 C. Infrared studies indicate that imide formation (curing) occurs at 149 C under vacuum. From a conceptual viewpoint, satisfactory film metallized on one side can be obtained by this method. The cured ultra thin polyimide film exhibits properties equivalent to those of commercial film, and the surface appearance of the strippable polyimide film compares favorably with that of a sample of commercial film of thicker gauge. The feasibility of manufacturing approximately one million sq m of ultra thin film capable of being joined to fabricate an 800 m by 9 800 m square from starting material 0.5 to 1 m wide for space erectable structures was demonstrated.

  6. Polymer-assisted deposition of films

    DOEpatents

    McCleskey, Thomas M.; Burrell, Anthony K.; Jia, Quanxi; Lin, Yuan

    2008-04-29

    A polymer assisted deposition process for deposition of metal oxide films is presented. The process includes solutions of one or more metal precursor and soluble polymers having binding properties for the one or more metal precursor. After a coating operation, the resultant coating is heated at high temperatures to yield metal oxide films. Such films can be epitaxial in structure and can be of optical quality. The process can be organic solvent-free.

  7. Polymer-assisted deposition of films

    DOEpatents

    McCleskey, Thomas M.; Burrell; Anthony K.; Jia; Quanxi; Lin; Yuan

    2009-10-20

    A polymer assisted deposition process for deposition of metal oxide films and the like is presented. The process includes solutions of one or more metal precursor and soluble polymers having binding properties for the one or more metal precursor. After a coating operation, the resultant coating is heated at high temperatures to yield metal oxide films and the like. Such films can be epitaxial in structure and can be of optical quality. The process can be organic solvent-free.

  8. Process for fabrication of metal oxide films

    SciTech Connect

    Tracy, C.E.; Benson, D.; Svensson, S.

    1990-07-17

    This invention is comprised of a method of fabricating metal oxide films from a plurality of reactants by inducing a reaction by plasma deposition among the reactants. The plasma reaction is effective for consolidating the reactants and producing thin films of metal oxides, e.g. electro-optically active transition metal oxides, at a high deposition rate. The presence of hydrogen during the plasma reaction enhances the deposition rate of the metal oxide. Various types of metal oxide films can be produced.

  9. Method of producing amorphous thin films

    DOEpatents

    Brusasco, Raymond M.

    1992-01-01

    Disclosed is a method of producing thin films by sintering which comprises: a. coating a substrate with a thin film of an inorganic glass forming parulate material possessing the capability of being sintered, and b. irridiating said thin film of said particulate material with a laser beam of sufficient power to cause sintering of said material below the temperature of liquidus thereof. Also disclosed is the article produced by the method claimed.

  10. Experiments On Transparent Conductive Films For Spacecraft

    NASA Technical Reports Server (NTRS)

    Perez-Davis, Marla E.; Rutledge, Sharon K.; De Groh, Kim K.; Hung, Ching-Cheh; Malave-Sanabria, Tania; Hambourger, Paul; Roig, David

    1995-01-01

    Report describes experiments on thin, transparent, electrically conductive films made, variously, of indium tin oxide covered by magnesium fluoride (ITO/MgF2), aluminum-doped zinc oxide (AZO), or pure zinc oxide (ZnO). Films are candidates for application to such spacecraft components, including various optoelectronic devices and window surfaces that must be protected against buildup of static electric charge. On Earth, such films useful on heat mirrors, optoelectronic devices, gas sensors, and automotive and aircraft windows.

  11. Anisotropic conducting films for electromagnetic radiation applications

    DOEpatents

    Cavallo, Francesca; Lagally, Max G.; Rojas-Delgado, Richard

    2015-06-16

    Electronic devices for the generation of electromagnetic radiation are provided. Also provided are methods for using the devices to generate electromagnetic radiation. The radiation sources include an anisotropic electrically conducting thin film that is characterized by a periodically varying charge carrier mobility in the plane of the film. The periodic variation in carrier mobility gives rise to a spatially varying electric field, which produces electromagnetic radiation as charged particles pass through the film.

  12. Exploding conducting film laser pumping apparatus

    DOEpatents

    Ware, K.D.; Jones, C.R.

    1984-04-27

    The 342-nm molecular iodine and the 1.315-..mu..m atomic iodine lasers have been optically pumped by intense light from exploding-metal-film discharges. Brightness temperatures for the exploding-film discharges were approximately 25,000 K. Although lower output energies were achieved for such discharges when compared to exploding-wire techniques, the larger surface area and smaller inductance inherent in the exploding-film should lead to improved efficiency for optically-pumped gas lasers.

  13. Poly(Arylene Ether Imidazole) Surface Films

    NASA Technical Reports Server (NTRS)

    Connell, John W.; Towell, Timothy W.; Tompkins, Stephen S.

    1993-01-01

    Films adhere well to some substrates, provide smooth surfaces, and facilitate release from molds. Thin films of thermoplastic poly(arylene ether imidazole)s (PAEI's) particularly suitable for use as surface modifiers for graphite/epoxy or graphite/bismaleimide composite panels. Molecule of PAEI includes imidazole groups along its backbone that co-cure with epoxies or bismaleimides during processing. Films thermally stable and resistant to bombardment by energetic electrons.

  14. Flexible Thin Metal Film Thermal Sensing System

    NASA Technical Reports Server (NTRS)

    Thomsen, Donald Laurence (Inventor)

    2012-01-01

    A flexible thin metal film thermal sensing system is provided. A thermally-conductive film made from a thermally-insulating material is doped with thermally-conductive material. At least one layer of electrically-conductive metal is deposited directly onto a surface of the thermally-conductive film. One or more devices are coupled to the layer(s) to measure an electrical characteristic associated therewith as an indication of temperature.

  15. Microcrystalline organic thin-film solar cells.

    PubMed

    Verreet, Bregt; Heremans, Paul; Stesmans, Andre; Rand, Barry P

    2013-10-11

    Microcrystalline organic films with tunable thickness are produced directly on an indium-tin-oxide substrate, by crystallizing a thin amorphous rubrene film followed by its use as a template for subsequent homoepitaxial growth. These films, with exciton diffusion lengths exceeding 200 nm, produce solar cells with increasing photocurrents at thicknesses up to 400 nm with a fill factor >65%, demonstrating significant potential for microcrystalline organic electronic devices. PMID:23939936

  16. Electrochemical photovoltaic cell having ternary alloy film

    DOEpatents

    Russak, Michael A.

    1984-01-01

    A thin film compound semiconductor electrode comprising CdSe.sub.1-x Te.sub.x (0.ltoreq.x.ltoreq.1) is deposited on a transparent conductive substrate. An electrolyte contacts the film to form a photoactive site. The semiconductor material has a narrow energy bandgap permitting high efficiency for light conversion. The film may be fabricated by: (1) co-evaporation of two II-VI group compounds with a common cation, or (2) evaporation of three elements, concurrenty.

  17. Important considerations for radiochromic film dosimetry with flatbed CCD scanners and EBT GAFCHROMIC[reg] film

    SciTech Connect

    Lynch, Bart D.; Kozelka, Jakub; Ranade, Manisha K.; Li, Jonathan G.; Simon, William E.; Dempsey, James F.

    2006-12-15

    In this study, we present three significant artifacts that have the potential to negatively impact the accuracy and precision of film dosimetry measurements made using GAFCHROMIC[reg] EBT radiochromic film when read out with CCD flatbed scanners. Films were scanned using three commonly employed instruments: a Macbeth TD932 spot densitometer, an Epson Expression 1680 CCD array scanner, and a Microtek ScanMaker i900 CCD array scanner. For the two scanners we assessed the variation in optical density (OD) of GAFCHROMIC EBT film with scanning bed position, angular rotation of the film with respect to the scan line direction, and temperature inside the scanner due to repeated scanning. Scanning uniform radiochromic films demonstrated a distinct bowing effect in profiles in the direction of the CCD array with a nonuniformity of up to 17%. Profiles along a direction orthogonal to the CCD array demonstrated a 7% variation. A strong angular dependence was found in measurements made with the flatbed scanners; the effect could not be reproduced with the spot densitometer. An IMRT quality assurance film was scanned twice rotating the film 90 deg. between the scans. For films scanned on the Epson scanner, up to 12% variation was observed in unirradiated EBT films rotated between 0 deg. and 90 deg. , which decreased to approximately 8% for EBT films irradiated to 300 cGy. Variations of up to 80% were observed for films scanned with the Microtek scanner. The scanners were found to significantly increase the film temperature with repeated scanning. Film temperature between 18 and 33 deg. C caused OD changes of approximately 7%. Considering these effects, we recommend adherence to a strict scanning protocol that includes: maintaining the orientation of films scanned on flatbed scanners, limiting scanning to the central portion of the scanner bed, and limiting the number of consecutive scans to minimize changes in OD caused by film heating.

  18. Polymer-assisted deposition of films

    DOEpatents

    McCleskey,Thomas M.; Burrell,Anthony K.; Jia,Quanxi; Lin,Yuan

    2012-02-28

    A polymer assisted deposition process for deposition of metal nitride films and the like is presented. The process includes solutions of one or more metal precursor and soluble polymers having binding properties for the one or more metal precursor. After a coating operation, the resultant coating is heated at high temperatures under a suitable atmosphere to yield metal nitride films and the like. Such films can be conformal on a variety of substrates including non-planar substrates. In some instances, the films can be epitaxial in structure and can be of optical quality. The process can be organic solvent-free.

  19. Insect thin films as solar collectors.

    PubMed

    Heilman, B D; Miaoulis, L N

    1994-10-01

    A numerical method for simulation of microscale radiation effects in insect thin-film structures is described. Accounting for solar beam and diffuse radiation, the model calculates the reflectivity and emissivity of such structures. A case study examines microscale radiation effects in butterfuly wings, and results reveal a new function of these multilayer thin films: thermal regulation. For film thicknesses of the order of 0.10 µm, solar absorption levels vary by as much as 25% with small changes in film thickness; for certain existing structures, absorption levels reach 96%., This is attributed to the spectral distribution of the reflected radiation, which consists of a singular reflectance peak within the solar spectrum.

  20. Analysis of Hard Thin Film Coating

    NASA Technical Reports Server (NTRS)

    Shen, Dashen

    1998-01-01

    MSFC is interested in developing hard thin film coating for bearings. The wearing of the bearing is an important problem for space flight engine. Hard thin film coating can drastically improve the surface of the bearing and improve the wear-endurance of the bearing. However, many fundamental problems in surface physics, plasma deposition, etc, need further research. The approach is using electron cyclotron resonance chemical vapor deposition (ECRCVD) to deposit hard thin film an stainless steel bearing. The thin films in consideration include SiC, SiN and other materials. An ECRCVD deposition system is being assembled at MSFC.

  1. Analysis of Hard Thin Film Coating

    NASA Technical Reports Server (NTRS)

    Shen, Dashen

    1998-01-01

    Marshall Space Flight Center (MSFC) is interested in developing hard thin film coating for bearings. The wearing of the bearing is an important problem for space flight engine. Hard thin film coating can drastically improve the surface of the bearing and improve the wear-endurance of the bearing. However, many fundamental problems in surface physics, plasma deposition, etc, need further research. The approach is using Electron Cyclotron Resonance Chemical Vapor Deposition (ECRCVD) to deposit hard thin film on stainless steel bearing. The thin films in consideration include SiC, SiN and other materials. An ECRCVD deposition system is being assembled at MSFC.

  2. Method for producing thin film electrodes

    DOEpatents

    Narayanan, Manoj; Ma, Beihai; Balachandran, Uthamalingam; Dorris, Stephen

    2016-06-07

    The invention provides for A method for producing pure phase strontium ruthenium oxide films, the method comprising solubilizing ruthenium-containing and strontium-containing compounds to create a mixture; subjecting the mixture to a first temperature above that necessary for forming RuO.sub.2 while simultaneously preventing formation of RuO.sub.2; maintaining the first temperature for a time to remove organic compounds from the mixture, thereby forming a substantially dry film; and subjecting the film to a second temperature for time sufficient to crystallize the film. Also provided is pure phase material comprising strontium ruthenium oxide wherein the material contains no RuO.sub.2.

  3. Surface acoustic wave propagation in graphene film

    SciTech Connect

    Roshchupkin, Dmitry Plotitcyna, Olga; Matveev, Viktor; Kononenko, Oleg; Emelin, Evgenii; Irzhak, Dmitry; Ortega, Luc; Zizak, Ivo; Erko, Alexei; Tynyshtykbayev, Kurbangali; Insepov, Zinetula

    2015-09-14

    Surface acoustic wave (SAW) propagation in a graphene film on the surface of piezoelectric crystals was studied at the BESSY II synchrotron radiation source. Talbot effect enabled the visualization of the SAW propagation on the crystal surface with the graphene film in a real time mode, and high-resolution x-ray diffraction permitted the determination of the SAW amplitude in the graphene/piezoelectric crystal system. The influence of the SAW on the electrical properties of the graphene film was examined. It was shown that the changing of the SAW amplitude enables controlling the magnitude and direction of current in graphene film on the surface of piezoelectric crystals.

  4. Surface tension profiles in vertical soap films

    NASA Astrophysics Data System (ADS)

    Adami, N.; Caps, H.

    2015-01-01

    Surface tension profiles in vertical soap films are experimentally investigated. Measurements are performed by introducing deformable elastic objets in the films. The shape adopted by those objects once set in the film is related to the surface tension value at a given vertical position by numerically solving the adapted elasticity equations. We show that the observed dependency of the surface tension versus the vertical position is predicted by simple modeling that takes into account the mechanical equilibrium of the films coupled to previous thickness measurements.

  5. Exploding conducting film laser pumping apparatus

    DOEpatents

    Ware, Kenneth D.; Jones, Claude R.

    1986-01-01

    Exploding conducting film laser optical pumping apparatus. The 342-nm molecular iodine and the 1.315-.mu.m atomic iodine lasers have been optically pumped by intense light from exploding-metal-film discharges. Brightness temperatures for the exploding-film discharges were approximately 25,000 K. Although lower output energies were achieved for such discharges when compared to exploding-wire techniques, the larger surface area and smaller inductance inherent in the exploding-film should lead to improved efficiency for optically-pumped gas lasers.

  6. Epitaxial growth of single crystal films

    NASA Technical Reports Server (NTRS)

    Lind, M. D.; Kroes, R. L.; Immorlica, A. A., Jr.

    1981-01-01

    An experiment in gallium arsenide liquid phase epitaxy (LPE) on a flight of the SPAR 6 is described. A general purpose LPE processor suitable for either SPAR or Space Transportation System flights was designed and built. The process was started before the launch, and only the final step, in which the epitaxial film is grown, was performed during the flight. The experiment achieved its objectives; epitaxial films of reasonably good quality and very nearly the thickness predicted for convection free diffusion limited growth were produced. The films were examined by conventional analytical techniques and compared with films grown in normal gravity.

  7. Preparation and characterization of gradient polymer films

    SciTech Connect

    Smith, S.C.

    1987-01-01

    Gradient polymers are multicomponent polymers whose chemical constitution varies with depth in the sample. Although these polymers may possess unique mechanical, optical, and barrier properties they remain relatively unexplored. This work is a study of the preparation of gradient polymers by sequential exposure of films to a diffusing monomer followed by electron beam irradiation. Initial experiments involved immersion of poly(vinyl chloride) (PVC) films in styrene or n-butyl methacrylate (BMA) for various time periods followed by irradiation with 1 or 10 megarads of accelerated electrons. A significant amount of poly(n-butyl methacrylate) (PBMA) formed in PVC/BMA systems, but little polystyrene could be found in the PVC/styrene films. A second set of experiments involved immersion of PVC and polyethylene (PE) films in BMA for 20, 40, 60, and 720 minutes followed by irradiation with 10 megarads of electrons. These films were then characterized using optical microscopy, quantitative transmission Fourier transform infrared spectroscopy (FTIR), and a depth profiling procedure based on quantitative attenuated total reflection (ATR) FTIR. It was concluded that the mechanism of PBMA formation in the polyethylene films was a result of events immediately following irradiation. Atmospheric oxygen diffusing into irradiated films trapped free radicals at the film surfaces. This was followed by storage in an evacuated desiccator where unintentional exposure to BMA vapor took place. This BMA reacted with free radicals that remained within the film cores, polymerizing to PBMA.

  8. Sputtering technology in solid film lubrication

    NASA Technical Reports Server (NTRS)

    Spalvins, T.

    1978-01-01

    Current and potential sputtering technology is reviewed as it applies primarily to the deposition of MoS2, though such lubricants as WS2 and PTFE are also considered. It is shown by electron microscopy and surface sensitive analytical techniques that the lubricating properties of sputtered MoS2 films are directly influenced by the sputtering parameters selected (i.e., power density, pressure, sputter etching, dc-biasing, etc.), substrate temperature, chemistry, topography, and environmental conditions during the friction test. Electron micrographs and diffractograms of sputtered MoS2 films clearly show the resultant changes in film morphology which affect film adherence and frictional properties.

  9. Sensitometric responses of selected medical radiographic films.

    PubMed

    Kofler, J M; Gray, J E

    1991-12-01

    Radiographic films produce different densities and contrast when processor changes occur, and the magnitude and rate of change vary with film type. The ability to detect and interpret the clinical importance of film density changes may depend on the method of sensitometry used. The characteristics of several medical radiographic films and various sensitometers were examined under three sensitometric variations and five processing variations. Of all variations used, only exposure with a single-versus a double-sided sensitometer caused a film type to have a marked different response. The results indicate that mismatching the sensitometer spectral output with the spectral sensitivity of the film in most cases does not affect the density changes of the film. The fact that a few films may be sensitive to differences in spectral content of the exposing light and dual- versus single-sided exposure and that only a limited number of film types were tested, however, leads to the prudent conclusion that the exposure conditions for quality control purposes should match clinical exposure conditions as closely as possible. PMID:1947114

  10. Cylinder wakes in flowing soap films

    SciTech Connect

    Vorobieff, P.; Ecke, R.E. ); Vorobieff, P. )

    1999-09-01

    We present an experimental characterization of cylinder wakes in flowing soap films. From instantaneous velocity and thickness fields, we find the vortex-shedding frequency, mean-flow velocity, and mean-film thickness. Using the empirical relationship between the Reynolds and Strouhal numbers obtained for cylinder wakes in three dimensions, we estimate the effective soap-film viscosity and its dependence on film thickness. We also compare the decay of vorticity with that in a simple Rankine vortex model with a dissipative term to account for air drag. [copyright] [ital 1999] [ital The American Physical Society

  11. Amorphous Insulator Films With Controllable Properties

    NASA Technical Reports Server (NTRS)

    Alterovitz, Samuel A.; Warner, Joseph D.; Liu, David C.; Pouch, John J.

    1987-01-01

    In experiments described in report, amorphous hydrogenated carbon films grown at room temperature by low-frequency plasma deposition, using methane or butane gas. Films have unique array of useful properties; (a) adhere to wide variety of materials; (b) contain only carbon and hydrogen; (c) smooth and free of pinholes; (d) resistant to attack by moisture and chemicals; and (e) have high electric-breakdown strength and electrical resistivity. Two of optical properties and hardness of this film controlled by deposition conditions. Amorphous a-C:H and BN films used for hermetic sealing and protection of optical, electronic, magnetic, or delicate mechanical systems, and for semiconductor field dielectrics.

  12. Poly-para-xylylene thin films: A study of the deposition chemistry, kinetics, film properties, and film stability

    NASA Astrophysics Data System (ADS)

    Fortin, Jeffrey Bernard

    Poly-para-xylylene, or parylene, thin films are chemically vapor deposited (CVD), conformal, pin-hole free polymeric thin films. They have found many industrial uses since there invention in 1947 and continue to find new applications in micro-electronics, biotechnology, and micro-electro-mechanical systems. In this study the deposition chemistry, deposition kinetics, film properties, and film stability were investigated. A differentially pumped quadrupole mass spectrometer was used to analyze the vapor species present during the CVD process. The identity of dimer contamination and its impact on the CVD process and film properties was studied. The quantitative conversion of dimer to monomer was investigated and it was found that conversion begins at around 385°C and by 565°C 100% conversion is obtained. The kinetics of the CVD process was analyzed for a range of substrate temperatures and chamber pressures. A new kinetic model based on a two-step adsorption was developed and fit the kinetic data well. This model should be appropriate for use with all parylene family polymers. Many of the properties of the films deposited in this study were analyzed. This includes a detailed study of surface morphology using atomic force microscopy which shows the interface width increases as a power law of film thickness. Other properties analyzed were the thermal stability, electrical properties, index of refraction, birefringence, hardness, and elastic modulus. The effect of ultraviolet (UV) radiation of lambda ≥ 250 nm on the thermal stability, electrical, and optical properties of thin parylene films was studied. The thermal stability and electrical properties of UV treated films were seen to deteriorate as the radiation dose increased. The stability of parylene thin films receiving plasma etching was analyzed. The dielectric constant, dissipation factor, and leakage current of plasma etched thin parylene films were investigated and found to be stable for the range of

  13. The Film News Omnibus. Volume One. Reviews of 16mm Films.

    ERIC Educational Resources Information Center

    Lee, Rohama, Ed.

    A total of 42 feature films and 450 documentaries and short subjects, some of which date back to the silent film era, are reviewed. The entire compilation is designed as a reference source for those who use 16mm films for education, information or entertainment in the classroom or other community agencies such as libraries, hospitals or prisons.…

  14. Linking Character Strengths and Learning with Films: A Content Analysis of Films for Adolescents

    ERIC Educational Resources Information Center

    Phaire, Dorothy W.

    2013-01-01

    Despite abundant research substantiating the value of teaching with films, there is a dearth of accessible resources that can help educators select films for positive modeling of character strengths. This scarcity exists in spite of the evidence that supports the efficacy of films' influence on young people. Young people today are receiving…

  15. The Wim Van Leer Competition for Young Film Makers at the Jerusalem Film Festival.

    ERIC Educational Resources Information Center

    Mendel, Gilli

    1999-01-01

    Describes the Jerusalem Film Center and the background, history, and organization of the Wim Van Leer Competition which was established for young filmmakers in high school. Describes the Jerusalem Film Festival, film studies programs at Israeli high schools, and future possibilities. (Author/LRW)

  16. English 5-6, 7-8: Film Study and Film Making.

    ERIC Educational Resources Information Center

    Bolton, Gerre M.

    This one-semester English elective course offered in grades 11 and 12 allows students to examine both classical and modern short films to determine the most effective elements of communication in the medium. The course is divided into two quarters and is further divided into topical sections, i.e., Teaching Poetry through Film, The Film as Visual…

  17. Cartoons and Animated Films Disney Wouldn't Have Made: Five Provocative Short Films

    ERIC Educational Resources Information Center

    Donelson, Kenneth L.

    1972-01-01

    Author provides and annotation of five short films listing, distributor, running time, rental price, summary, possible audiences, some strengths and weaknesses, thematic units it might fit, some related books and films, and a few questions students or teachers might consider in a discussion of the film or its content. (Author)

  18. Film as Revolutionary Weapon: A Pedagogical Analysis. Latin American Studies Program, Film Series No. 3.

    ERIC Educational Resources Information Center

    California Univ., Riverside. Latin American Studies Program.

    This paper describes a university course designed to examine the use of film as a revolutionary medium in Latin American countries. Objectives of the course were to illustrate the complexity of studying a film genre, develop an analytical framework for comparing revolutionary films, and encourage students to reach their own conclusions about the…

  19. Thermal Transport across a Substrate-Thin-Film Interface: Effects of Film Thickness and Surface Roughness

    NASA Astrophysics Data System (ADS)

    Liang, Zhi; Sasikumar, Kiran; Keblinski, Pawel

    2014-08-01

    Using molecular dynamics simulations and a model AlN-GaN interface, we demonstrate that the interfacial thermal resistance RK (Kapitza resistance) between a substrate and thin film depends on the thickness of the film and the film surface roughness when the phonon mean free path is larger than film thickness. In particular, when the film (external) surface is atomistically smooth, phonons transmitted from the substrate can travel ballistically in the thin film, be scattered specularly at the surface, and return to the substrate without energy transfer. If the external surface scatters phonons diffusely, which is characteristic of rough surfaces, RK is independent of film thickness and is the same as RK that characterizes smooth surfaces in the limit of large film thickness. At interfaces where phonon transmission coefficients are low, the thickness dependence is greatly diminished regardless of the nature of surface scattering. The film thickness dependence of RK is analogous to the well-known fact of lateral thermal conductivity thickness dependence in thin films. The difference is that phonon-boundary scattering lowers the in-plane thermal transport in thin films, but it facilitates thermal transport from the substrate to the thin film.

  20. A superior process for forming titanium hydrogen isotopic films

    NASA Technical Reports Server (NTRS)

    Steinberg, R.; Alger, D. L.; Cooper, D. W.

    1975-01-01

    Process forms stoichiometric, continuous, strongly bonded titanium hydrogen isotopic films. Films have thermal and electrical conductivities approximately the same as bulk pure titanium, ten times greater than those of usual thin films.