Textile-Based Weft Knitted Strain Sensors: Effect of Fabric Parameters on Sensor Properties

PubMed Central

Atalay, Ozgur; Kennon, William Richard; Husain, Muhammad Dawood

2013-01-01

The design and development of textile-based strain sensors has been a focus of research and many investigators have studied this subject. This paper presents a new textile-based strain sensor design and shows the effect of base fabric parameters on its sensing properties. Sensing fabric could be used to measure articulations of the human body in the real environment. The strain sensing fabric was produced by using electronic flat-bed knitting technology; the base fabric was produced with elastomeric yarns in an interlock arrangement and a conductive yarn was embedded in this substrate to create a series of single loop structures. Experimental results show that there is a strong relationship between base fabric parameters and sensor properties. PMID:23966199

Performance of resin transfer molded multiaxial warp knit composites

NASA Technical Reports Server (NTRS)

Dexter, H. Benson; Hasko, Gregory H.

1993-01-01

Composite materials that are subjected to complex loads have traditionally been fabricated with multidirectionally oriented prepreg tape materials. Some of the problems associated with this type of construction include low delamination resistance, poor out-of-plane strength, and labor intensive fabrication processes. Textile reinforced composites with through-the-thickness reinforcement have the potential to solve some of these problems. Recently, a relatively new class of noncrimp fabrics designated as multiaxial warp knits have been developed to minimize some of the high cost and damage tolerance concerns. Multiple stacks of warp knit fabrics can be knitted or stitched together to reduce layup labor cost. The through-the-thickness reinforcement can provide significant improvements in damage tolerance and out-of-plane strength. Multilayer knitted/stitched preforms, in conjunction with resin transfer molding (RTM), offer potential for significant cost savings in fabrication of primary aircraft structures. The objectives of this investigation were to conduct RTM processing studies and to characterize the mechanical behavior of composites reinforced with three multiaxial warp knit fabrics. The three fabrics investigated were produced by Hexcel and Milliken in the United States, and Saerbeck in Germany. Two resin systems, British Petroleum E9O5L and 3M PR 500, were characterized for RTM processing. The performance of Hexcel and Milliken quasi-isotropic knitted fabrics are compared to conventional prepreg tape laminates. The performance of the Saerbeck fabric is compared to uniweave wing skin layups being investigated by Douglas Aircraft Company in the NASA Advanced Composites Technology (ACT) program. Tests conducted include tension, open hole tension, compression, open hole compression, and compression after impact. The effects of fabric defects, such as misaligned fibers and gaps between tows, on material performance are also discussed. Estimated material and labor

Multiple faces of contemporary hand knitting

NASA Astrophysics Data System (ADS)

Pavko-Čuden, A.

2017-10-01

Knitting and crocheting are traditional textile techniques with great significance both in history and modern times. Similar to other textile techniques, knitting has developed into a diversified industrial sector, comprising the production of knitted fabrics, knitwear, hosiery and fashion accessories. At the same time, contemporary knitting and crocheting became hobbies as well as arts-and-crafts activities, extending to various areas of work and leisure. Historical and traditional ethnic knitting and crocheting patterns keep inspiring designers’ collections and also other industrial products. Not so long ago, knitting was seen as an ordinary and unchanging indoor activity and, in its domestic history, it was the preserve of older women making products of dainty work and taste. Today, knitting deals with urban population of all classes. The popularity of leisure hand knitting is increasing; moreover, hand knitting is becoming more and more widespread among young people. With the emergence of artistic and handicraft markets, hand-knitting and crocheting developed into a profitable market activity. Positive effects of hand knitting have become increasingly important - from generating creativity and innovativeness, through knitting and socializing in groups, to medical and therapeutic effects as well as social and global connections. Yarn bombing, yarn storming or graffiti knitting has been used to describe urban social practices of knitted objects placed, or tagged, in public spaces. Knitting became means of communication, artistic and social expression and statement. The advantage of hand knitting is its mobility. One can knit almost everywhere, and for hand knitting, only a ball of yarn and knitting needles are required. Handknitted products have nice touch, they are custom-made and therefore personalized.

Multi-Scaled Modeling the Mechanical Properties of Tubular Composites Reinforced with Innovated 3D Weft Knitted Spacer Fabrics

NASA Astrophysics Data System (ADS)

Omrani, Elahe; Hasani, Hossein; Dibajian, Sayed Houssain

2018-02-01

Textile composites of 3D integrated spacer configurations have been recently focused by several researchers all over the world. In the present study, newly-designed tubular composites reinforced with 3D spacer weft knitted fabrics were considered and the effects of their structural parameters on some applicable mechanical properties were investigated. For this purpose, two different samples of 3D spacer weft knitted textile types in tubular form were produced on an electronic flat knitting machine, using glass/nylon hybrid yarns. Thermoset tubular-shaped composite parts were manufactured via vacuum infusion molding process using epoxy resin. The mechanical properties of the produced knitted composites in term of external static and internal hydrostatic pressures were evaluated. Resistance of the produced composites against the external static and internal hydrostatic pressures was numerically simulated using multi-scale modeling method. The finding revealed that there is acceptable correlation between experimental and theoretical results.

The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

NASA Astrophysics Data System (ADS)

Halavska, L.; Batrak, O.

2016-07-01

A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

In-Vitro Analysis of the Effect of Constructional Parameters and Dye Class on the UV Protection Property of Cotton Knitted Fabrics.

PubMed

Kan, Chi-Wai; Au, Chui-Ha

2015-01-01

Cotton knitted fabrics were manufactured with different yarn types (conventional ring spun yarn and torque-free ring spun yarn) with different fibre types (combed cotton and combed Supima cotton) and yarn fineness (Ne30 and Ne40). These fabrics were then dyed with three types of dye (reactive, direct and sulphur dye) with three dye concentrations (0.1%, 1.0% and 5.0% on-weight of fabric (owf)) in three colours (red, yellow and blue). This study examined the impact of constructional parameters and dyeing on ultraviolet (UV) protection properties of cotton knitted fabric. In-vitro test with spectrophotometer was used for evaluating the UV protection property of dyed cotton knitted fabrics. Among the six parameters investigated, fineness of yarn and dye concentration were the most significant factors affecting UPF while the color effect is the least significant. Experimental results revealed that the UPF value of dyed fabrics made from combed cotton is generally higher than the combed Supima cotton since combed cotton is composed of shorter fibres which facilitate the blocking or absorption of UV radiation. Second, fabrics made with twist yarn (i.e. ring spun yarn) have higher UPF value than the corresponding ESTex one (i.e. torque-free yarn) in general since fabrics made with ring spun yarn tend to shrink during wet processing and so it is more compact. Third, the UPF value of fabrics made with 30Ne yarn was higher than the 40Ne one since it is thicker and has lower fabric porosity. Fourth, fabrics dyed with lower concentration of dye gave the lowest UPF. Fifth, the sulphur dyed samples performed worse than the reactive and direct dyed samples in terms of UV protection property. Sixth, there is no significant difference in UPF for red, yellow and blue coloured fabrics. Seventh, this study also demonstrated that lightness of fabric is negatively related to UV protection property.

In-Vitro Analysis of the Effect of Constructional Parameters and Dye Class on the UV Protection Property of Cotton Knitted Fabrics

PubMed Central

2015-01-01

Cotton knitted fabrics were manufactured with different yarn types (conventional ring spun yarn and torque-free ring spun yarn) with different fibre types (combed cotton and combed Supima cotton) and yarn fineness (Ne30 and Ne40). These fabrics were then dyed with three types of dye (reactive, direct and sulphur dye) with three dye concentrations (0.1%, 1.0% and 5.0% on-weight of fabric (owf)) in three colours (red, yellow and blue). This study examined the impact of constructional parameters and dyeing on ultraviolet (UV) protection properties of cotton knitted fabric. In-vitro test with spectrophotometer was used for evaluating the UV protection property of dyed cotton knitted fabrics. Among the six parameters investigated, fineness of yarn and dye concentration were the most significant factors affecting UPF while the color effect is the least significant. Experimental results revealed that the UPF value of dyed fabrics made from combed cotton is generally higher than the combed Supima cotton since combed cotton is composed of shorter fibres which facilitate the blocking or absorption of UV radiation. Second, fabrics made with twist yarn (i.e. ring spun yarn) have higher UPF value than the corresponding ESTex one (i.e. torque-free yarn) in general since fabrics made with ring spun yarn tend to shrink during wet processing and so it is more compact. Third, the UPF value of fabrics made with 30Ne yarn was higher than the 40Ne one since it is thicker and has lower fabric porosity. Fourth, fabrics dyed with lower concentration of dye gave the lowest UPF. Fifth, the sulphur dyed samples performed worse than the reactive and direct dyed samples in terms of UV protection property. Sixth, there is no significant difference in UPF for red, yellow and blue coloured fabrics. Seventh, this study also demonstrated that lightness of fabric is negatively related to UV protection property. PMID:26222792

Investigation of Comfort Properties of Knitted Denim

NASA Astrophysics Data System (ADS)

Akbar, Abdul R.; Su, Siwei; Khalid, Junaid; Cai, Yingjie; Lin, Lina

2017-12-01

Knitted denim was designed by using cross terry structure on circular knitting machine. Knitted denim looks like a denim fabric which has visual appearance like woven denim. Two type of cross terry structure 2/1 and 3/1 were used which gives twill effect with 2 and 3 floats respectively. Four types of materials, cotton, polyester, flax and polypropylene were used. With four materials and two structural combinations 8 samples were produced. Comfort properties of knitted denim including moisture management, air permeability, thermal, and bursting strength were tested. For checking the inherent anti-microbial property of materials anti-microbial test was also applied. Samples containing flax and polyester were found with best results and not even a single sample was found anti-microbial.

Knitting and weaving artificial muscles

PubMed Central

Maziz, Ali; Concas, Alessandro; Khaldi, Alexandre; Stålhand, Jonas; Persson, Nils-Krister; Jager, Edwin W. H.

2017-01-01

A need exists for artificial muscles that are silent, soft, and compliant, with performance characteristics similar to those of skeletal muscle, enabling natural interaction of assistive devices with humans. By combining one of humankind’s oldest technologies, textile processing, with electroactive polymers, we demonstrate here the feasibility of wearable, soft artificial muscles made by weaving and knitting, with tunable force and strain. These textile actuators were produced from cellulose yarns assembled into fabrics and coated with conducting polymers using a metal-free deposition. To increase the output force, we assembled yarns in parallel by weaving. The force scaled linearly with the number of yarns in the woven fabric. To amplify the strain, we knitted a stretchable fabric, exhibiting a 53-fold increase in strain. In addition, the textile construction added mechanical stability to the actuators. Textile processing permits scalable and rational production of wearable artificial muscles, and enables novel ways to design assistive devices. PMID:28138542

Style in knitted textiles and fashion

NASA Astrophysics Data System (ADS)

Štemberger, M.; Pavko-Čuden, A.

2017-10-01

The presented research relates the basic elements of the art theory with the concept of style and fashion design. The objective of the research was to determine how style is manifested in knitting in different periods of fashion seasons. The collections of three designers were compared: Missoni, Issey Miyake and Sonia Rykiel, in four different seasons in three different years. The basic artistic elements used in the presented research were: point, line, light-dark and colour together with syntactic rules. A combination of different elements and syntactic rules refers to different artistic languages, which have their own artistic grammar, i.e. a different style. All three investigated fashion designers used knitting in their collections as a significant element which defined their style. Different knitting technologies as well as different yarns made of synthetic or natural fibres in all colour spectra significantly influence the surface of a knitted fabric. Even when the technology is the same, the use of different materials, structures, colours, etc. creates various unique surfaces. The method used in the presented research was a style matrix which is developed from the axiomatic system. Only the part dealing with the language of fine arts and the pictorial speech - the style of a certain designer and a certain work of art/knitted fabric was used. After the selected three designers were examined through all the periods, it was concluded that each designer can be characterised by his own style. Despite the influencing fashion trends, all the compared designers still retained their own style, their own techniques, their own inspirations.

Industrial applications of multiaxial warp knit composites

NASA Technical Reports Server (NTRS)

Kaufmann, James R.

1992-01-01

Over the past few years, multiaxial warp knit (MWK) fabrics have made significant inroads into the industrial composites arena. This paper examines the use of MWK fabrics in industrial composite applications. Although the focus is on current applications of MWK fabrics in composites, this paper also discusses the physical properties, advantages and disadvantages of MWK fabrics. The author also offers possibilities for the future of MWK fabrics in the industrial composites arena.

Aspects of the dimensional changes of jersey structures after knitting process

NASA Astrophysics Data System (ADS)

Szabo, M.; Barbu, I.; Jiaru, L.

2017-08-01

The study proposes a statistical analysis by applying a mathematical model for the study of the dimensional changes of jersey structures made of 100% cotton yarn, with 58/1 metric count of yarn. The Structures are presented as tubular knitted metrage and are designed for underwear and/or outer garments. By analysing the jersey structures, from dimensional stability point of view, there can be observed that values in the limits are within the ±2% interval, values which are considered appropriate. Following the experimental researches, there are proposed solutions for the reduction of dimensional changes on both directions of the knit, on the stich course direction and also on the stich courses in vertical direction, being analyzed the behaviour of the knitted fabrics during relaxation after knitting process. The problem of the dimensional stability of the knitted fabrics is extensive researched. The knitted structures are elastic structures, this being a reason for which dimensional stability will always be a topical theme. The jersey structures, due to the distribution of the platinum loop in the knit plane, due to the relative small number of yarn-yarn contact points that causes the threads to slide into the structure, due to the spiral of the tubular metrage structure, are among those whose dimensional stability is difficult to control. The technical characteristics of the yarns, the technical characteristics of the knitting machines and the technological parameters of the knitting machine are the elements which will be correlated in order to obtain structures with minimum dimensional changes. In order to obtain knitted structures with adequate dimensional stability, this means within ±2%, it is necessary that the dimensional changes during the relaxation periods after knitting and chemical finishing being minimum. For this, all the processes to be applied will be conducted with appropriate and uniform tensions throughout the technological flow. The relaxation

Characterization of multiaxial warp knit composites

NASA Technical Reports Server (NTRS)

Dexter, H. Benson; Hasko, Gregory H.; Cano, Roberto J.

1991-01-01

The objectives were to characterize the mechanical behavior and damage tolerance of two multiaxial warp knit fabrics to determine the acceptability of these fabrics for high performance composite applications. The tests performed included compression, tension, open hole compression, compression after impact and compression-compression fatigue. Tests were performed on as-fabricated fabrics and on multi-layer fabrics that were stitched together with either carbon or Kevlar stitching yarn. Results of processing studies for vacuum impregnation with Hercules 3501-6 epoxy resin and pressure impregnation with Dow Tactix 138/H41 epoxy resin and British Petroleum BP E905L epoxy resin are presented.

Data on kilometer scale production of stretchable conductive multifilaments enables knitting wearable strain sensing textiles.

PubMed

Seyedin, Shayan; Moradi, Sepehr; Singh, Charanpreet; Razal, Joselito M

2018-06-01

This data article contains analyzed data for the article "Continuous Production of Stretchable Conductive Multifilaments in Kilometer Scale Enables Facile Knitting of Wearable Strain Sensing Textiles" (Seyedin et al., 2018) [1]. Details of wet-spinning conditions to achieve scaled-up production of stretchable and conducting polyurethane/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PU/PEDOT:PSS) multifilaments are provided. The stress-strain curves for tensile and stretch-relaxation tests on the multifilament and different knitted textile structures (plain-knit, co-knit, co-knit-alternate, co-knit with conductive stitch, and plain with non-conductive stitch) are presented. It is shown that the PU/PEDOT:PSS multifilaments can also be knitted into fabrics that when worn on various body parts, such as knee, elbow, and finger, can monitor their various movements.

A constitutive model for the warp-weft coupled non-linear behavior of knitted biomedical textiles.

PubMed

Yeoman, Mark S; Reddy, Daya; Bowles, Hellmut C; Bezuidenhout, Deon; Zilla, Peter; Franz, Thomas

2010-11-01

Knitted textiles have been used in medical applications due to their high flexibility and low tendency to fray. Their mechanics have, however, received limited attention. A constitutive model for soft tissue using a strain energy function was extended, by including shear and increasing the number and order of coefficients, to represent the non-linear warp-weft coupled mechanics of coarse textile knits under uniaxial tension. The constitutive relationship was implemented in a commercial finite element package. The model and its implementation were verified and validated for uniaxial tension and simple shear using patch tests and physical test data of uniaxial tensile tests of four very different knitted fabric structures. A genetic algorithm with step-wise increase in resolution and linear reduction in range of the search space was developed for the optimization of the fabric model coefficients. The numerically predicted stress-strain curves exhibited non-linear stiffening characteristic for fabrics. For three fabrics, the predicted mechanics correlated well with physical data, at least in one principal direction (warp or weft), and moderately in the other direction. The model exhibited limitations in approximating the linear elastic behavior of the fourth fabric. With proposals to address this limitation and to incorporate time-dependent changes in the fabric mechanics associated with tissue ingrowth, the constitutive model offers a tool for the design of tissue regenerative knit textile implants. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

40 CFR 410.52 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing... attributable to the finishing of knit fabrics through simple manufacturing operations employing a natural and..., controlled by this section and attributable to the finishing of knit fabrics through complex manufacturing...

40 CFR 410.52 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing... attributable to the finishing of knit fabrics through simple manufacturing operations employing a natural and..., controlled by this section and attributable to the finishing of knit fabrics through complex manufacturing...

Mechanical Characteristics of Composite Knitted Stents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tokuda, Takanori, E-mail: tkdtknr@gmail.com; Shomura, Yuzo; Tanigawa, Noboru

2009-09-15

We used metal wires and fibers to fabricate a composite knitted stent and then compare the mechanical characteristics of this stent with those of a pure metallic stent of the same construction in order to develop a stent that offers a comparable degree of expandability as metallic stents but can be used for highly curved lesions that cannot be treated using metallic stents. We fabricated two types of composite knitted stent (N-Z stents), using nitinol wire with a diameter of 0.12 mm and polypara-phenylene-benzobisoxazole (PBO) multifilament fiber (Zyron AS; Toyobo, Osaka, Japan). Stents were knitted into a cylindrical shape usingmore » the same textile pattern as a Strecker stent. Two loop lengths (L) of nitinol wire were used in the N-Z stents: L = 1.84 mm (N-Z stent L = 1.84) and L = 2.08 mm (N-Z stent L = 2.08). For the sake of comparison, we fabricated a metallic stent of nitinol using the same textile pattern (N-N stent L = 1.92). We applied a radial compression force diametrically to each stent and applied a bending force diametrically at the free end of a stent with one end fixed in order to evaluate the relationship between stent elasticity and load values. In addition, we macroscopically evaluated the generation of kinks when the stent was bent 180{sup o}. The radial compressive force when the stent diameter was reduced by 53% was 6.44 N in the case of N-Z stent L = 1.84, 6.14 N in the case of N-Z stent L = 2.08, and 4.96 N in the case of N-N stent L = 1.92 mm. The composite stent had a radial compressive force higher than that of a metallic stent. The restoring force to longitudinal direction at a 90{sup o} bending angle was 0.005 N for N-Z stent L = 1.84, 0.003 N for N-Z stent L = 2.08, and 0.034 N for N-N stent L = 1.92. The restoring force of the composite stent was significantly lower. Finally, the composite stent generated no definitive kinks at a bending angle of 180{sup o}, regardless of loop length. However, the N-N stent clearly produced kinks

A knitted glove sensing system with compression strain for finger movements

NASA Astrophysics Data System (ADS)

Ryu, Hochung; Park, Sangki; Park, Jong-Jin; Bae, Jihyun

2018-05-01

Development of a fabric structure strain sensor has received considerable attention due to its broad application in healthcare monitoring and human–machine interfaces. In the knitted textile structure, it is critical to understand the surface structural deformation from a different body motion, inducing the electrical signal characteristics. Here, we report the electromechanical properties of the knitted glove sensing system focusing on the compressive strain behavior. Compared with the electrical response of the tensile strain, the compressive strain shows much higher sensitivity, stability, and linearity via different finger motions. Additionally, the sensor exhibits constant electrical properties after repeated cyclic tests and washing processes. The proposed knitted glove sensing system can be readily extended to a scalable and cost-effective production due to the use of a commercialized manufacturing system.

Comparison Of Flat-Knitted Structures Made Of Poly(P-Phenylene-2,6-Benzobisoxazole) And Para-Aramid Referring To Their Stab Resistance

NASA Astrophysics Data System (ADS)

Obermann, M.; Aumann, S.; Heimlich, F.; Weber, M. O.; Schwarz-Pfeiffer, A.

2016-07-01

In the field of protective gear, developers always aim for lighter and more flexible material in order to increase the wearing comfort. Suppliers now work on knitted garments in the sports-sector as well as in workwear and protective gear for policemen or security-agents. In a recent project different knitted structures made of a poly(p-phenylene-2,6-benzobisoxazole) (PBO)-multifilament were compared to their counterparts made of para-aramid. In focus of the comparison stood the stab-resistance linked to either the mass per unit area or the stitch density. The tested fabrics were produced on hand flat knitting machines as well as on electronical flat knitting machines of the type Stoll CMS 330TC4, in order to analyse fabrics with different tightness factor and machine gauges. The stab resistance of the different knitted fabrics was examined according to the standard of the Association of Test Laboratories for Bullet, Stab or Pike Resistant Materials and Construction Standards. The presentation includes the depiction of the results of the test series and their interpretation. Furthermore it will give an outlook on most suitable combinations of materials and structures to be used in protective gear.

Legitimate Fidgeting: Knitting with Kids

ERIC Educational Resources Information Center

Austen, Judith

2006-01-01

In this article, the author relates how she learned knitting and how she taught this craft to her own students. She learned knitting at the age of 40. After learning how to knit, she introduced the craft to her students as part of the art curriculum at Shady Hill School. She realized how knitting not only promotes intimacy, but it also helps…

A Need to Knit

ERIC Educational Resources Information Center

Gruener, Barbara

2006-01-01

In this article, the author talks about the Westwood Elementary's knitting and crochet club. The idea for this group unraveled when one of their third graders received a knitting kit as a birthday gift. The mother of the student told the author what a wonderful hobby knitting had become for her daughter and how this craft worked to help develop…

Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents

PubMed Central

Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

2017-01-01

One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design—wearable APP (WAPP)—that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents. PMID:28098192

Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents

NASA Astrophysics Data System (ADS)

Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

2017-01-01

One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design—wearable APP (WAPP)—that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents.

Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents.

PubMed

Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

2017-01-18

One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design-wearable APP (WAPP)-that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents.

The effect of fabric structure on the mechanical properties of warp knitted surgical mesh for hernia repair.

PubMed

Mirjavan, Mohammad; Asayesh, Azita; Asgharian Jeddi, Ali Asghar

2017-02-01

Surgical mesh is being used for healing hernia, pelvic organ prolapse, skull injuries and urinary incontinence. In this research the effect of fabric structure on the mechanical properties of warp knitted surgical meshes in comparison to abdominal fascia has been investigated. For this purpose, warp knitted surgical mesh with five different structures (Tricot, Pin-hole-net, quasi-Sandfly, Sandfly and quasi-Marquissite) were produced using polypropylene monofilament. Thereafter, their mechanical properties such as uniaxial tensile behavior in various directions (wale-wise (90°), course-wise (0°) and diagonal (45°)), bending resistance and crease recovery were analyzed. The meshes demonstrated different elastic modulus in various directions, which can be attributed to the pore shape (pore angle) and underlap angle in the structure of mesh. Except Pin-hole-net mesh, other produced meshes exhibited better level of orthotropy in comparison to abdominal fascia. The most flexible mesh in both wale-wise and course-wise directions was quasi-Sandfly and thereafter quasi-Marquissite. Tricot and Pin-hole-net manifested the highest crease recovery in wale-wise and coursewise directions respectively. The most desirable mesh in terms of porosity was quasi-Marquissite mesh. Overall, the quasi-Marquissite mesh was selected as the most suitable surgical mesh considering all advantages and disadvantages of each produced mesh in this study. Copyright © 2016 Elsevier Ltd. All rights reserved.

One-step manufacturing of innovative flat-knitted 3D net-shape preforms for composite applications

NASA Astrophysics Data System (ADS)

Bollengier, Quentin; Wieczorek, Florian; Hellmann, Sven; Trümper, Wolfgang; Cherif, Chokri

2017-10-01

Mostly due to the cost-intensive manually performed processing operations, the production of complex-shaped fibre reinforced plastic composites (FRPC) is currently very expensive and therefore either restricted to sectors with high added value or for small batch applications (e.g. in the aerospace or automotive industry). Previous works suggest that the successful integration of conventional textile manufacturing processes in the FRPC-process chain is the key to a cost-efficient manufacturing of complex three-dimensional (3D) FRPC-components with stress-oriented fibre arrangement. Therefore, this work focuses on the development of the multilayer weft knitting technology for the one-step manufacturing of complex 3D net-shaped preforms for high performance FRPC applications. In order to highlight the advantages of net-shaped multilayer weft knitted fabrics for the production of complex FRPC parts, seamless preforms such as 3D skin-stringer structures and tubular fabrics with load oriented fibre arrangement are realised. In this paper, the development of the textile bindings and performed technical modifications on flat knitting machines are presented. The results show that the multilayer weft knitting technology meets perfectly the requirements for a fully automated and reproducible manufacturing of complex 3D textile preforms with stress-oriented fibre arrangement.

Moisture Management Behaviour of Knitted Fabric from Structurally Modified Ring and Vortex Spun Yarn

NASA Astrophysics Data System (ADS)

Sharma, Navendu; Kumar, Pawan; Bhatia, Dinesh; Sinha, Sujit Kumar

2016-10-01

The acceptability of a new product is decided by its performance, level of improvement in quality and economy of production. The basic aim of generating micro pores in a textile structure is to provide better thermo-physiological comfort by enhancing the breathability and hence improving moisture management behaviour. In the present study, an attempt has been made to create a relatively more open structure through removal of a component. A comparative assessment with a homogeneous and parent yarn was also made. Yarns of two linear densities, each from ring and vortex spinning systems were produced using 100 % polyester and 80:20 polyester/cotton blend. The modified yarn was produced by removing a component, viz; cotton, by treatment with sulphuric acid from the blended yarn. The knitted fabric from modified yarn was found to show significant improvement in air permeability, water vapour permeability and total absorbency while the wicking characteristic was found to decline.

40 CFR 410.51 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory § 410.51 Specialized... the knit fabric finishing subcategory for facilities that are engaged primarily in dyeing or finishing...

40 CFR 410.51 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory § 410.51 Specialized... the knit fabric finishing subcategory for facilities that are engaged primarily in dyeing or finishing...

Recent developments in multi-layer flat knitting technology for waste free production of complex shaped 3D-reinforcing structures for composites

NASA Astrophysics Data System (ADS)

Trümper, W.; Lin, H.; Callin, T.; Bollengier, Q.; Cherif, C.; Krzywinski, S.

2016-07-01

Constantly increasing prices for raw materials and energy as well as the current discourse on the reduction of CO2-emissions places a special emphasis on the advantages of lightweight constructions and its resource conserving production methods. Fibre-reinforced composites are already seeing a number of applications in automobile, energy and mechanical engineering. Future applications within the named areas require greater material and energy efficiency and therefore manufacturing methods for textile preforms and lightweight constructions enabling an optimal arrangement of the reinforcing fibres while in the same time limiting waste to a minimum. One manufacturing method for textile reinforced preforms fulfilling quite many of the named requirements is the multilayer weft knitting technology. Multilayer weft knitted fabrics containing straight reinforcing yarns at least in two directions. The arrangement of these yarns is fixed by the loop yarn. Used yarn material in each knitting row is adaptable e. g. according to the load requirements or for the local integration of sensors. Draping properties of these fabrics can be varied within a great range and through this enabling draping of very complex shaped 3D-preforms without wrinkles from just one uncut fabric. The latest developments at ITM are concentrating on the development of a full production chain considering the 3D-CAD geometry, the load analysis, the generation of machine control programs as well as the development of technology and machines to enable the manufacturing of innovative net shape 3D-multilayer weft knitted fabrics such as complex shaped spacer fabrics and tubular fabrics with biaxial reinforcement.

Structure and yarn sensor for fabric

DOEpatents

Mee, David K.; Allgood, Glenn O.; Mooney, Larry R.; Duncan, Michael G.; Turner, John C.; Treece, Dale A.

1998-01-01

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric.

Structure and yarn sensor for fabric

DOEpatents

Mee, D.K.; Allgood, G.O.; Mooney, L.R.; Duncan, M.G.; Turner, J.C.; Treece, D.A.

1998-10-20

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric. 13 figs.

Knitting: A Craft Makes a Comeback

ERIC Educational Resources Information Center

McIntosh, Phyllis

2011-01-01

Hand knitting is one of the most popular hobbies in the United States. Once considered the province of grannies and expectant mothers stitching layettes, knitting is enjoying a 21st century resurgence, especially among young people. Knitting, it turns out, is a trendy, often eco-friendly pastime with a wide range of appeals. And, thanks to the…

Energy harvesting “3-D knitted spacer” based piezoelectric textiles

NASA Astrophysics Data System (ADS)

Anand, S.; Soin, N.; Shah, T. H.; Siores, E.

2016-07-01

The piezoelectric effect in Poly(vinylidene fluoride), PVDF, was discovered over four decades ago and since then, significant work has been carried out aiming at the production of high p-phase fibres and their integration into fabric structures for energy harvesting. However, little work has been done in the area of production of “true piezoelectric fabric structures” based on flexible polymeric materials such as PVDF. In this work, we demonstrate “3-D knitted spacer” technology based all-fibre piezoelectric fabrics as power generators and energy harvesters. The knitted single-structure piezoelectric generator consists of high p-phase (~80%) piezoelectric PVDF monofilaments as the spacer yarn interconnected between silver (Ag) coated polyamide multifilament yarn layers acting as the top and bottom electrodes. The novel and unique textile structure provides an output power density in the range of 1.105.10 gWcm-2 at applied impact pressures in the range of 0.02-0.10 MPa, thus providing significantly higher power outputs and efficiencies over the existing 2-D woven and nonwoven piezoelectric structures. The high energy efficiency, mechanical durability and comfort of the soft, flexible and all-fibre based power generator is highly attractive for a variety of potential applications such as wearable electronic systems and energy harvesters charged from ambient environment or by human movement.

A Highly Stretchable and Washable All-Yarn-Based Self-Charging Knitting Power Textile Composed of Fiber Triboelectric Nanogenerators and Supercapacitors.

PubMed

Dong, Kai; Wang, Yi-Cheng; Deng, Jianan; Dai, Yejing; Zhang, Steven L; Zou, Haiyang; Gu, Bohong; Sun, Baozhong; Wang, Zhong Lin

2017-09-26

Rapid advancements in stretchable and multifunctional wearable electronics impose a challenge on corresponding power devices that they should have comparable portability and stretchability. Here, we report a highly stretchable and washable all-yarn-based self-charging knitting power textile that enables both biomechanical energy harvesting and simultaneously energy storing by hybridizing triboelectrical nanogenerator (TENG) and supercapacitor (SC) into one fabric. With the weft-knitting technique, the power textile is qualified with high elasticity, flexibility, and stretchability, which can adapt to complex mechanical deformations. The knitting TENG fabric is able to generate electric energy with a maximum instantaneous peak power density of ∼85 mW·m -2 and light up at least 124 light-emitting diodes. The all-solid-state symmetrical yarn SC exhibits lightweight, good capacitance, high flexibility, and excellent mechanical and long-term stability, which is suitable for wearable energy storage devices. The assembled knitting power textile is capable of sustainably driving wearable electronics (for example, a calculator or temperature-humidity meter) with energy converted from human motions. Our work provides more opportunities for stretchable multifunctional power sources and potential applications in wearable electronics.

Investigation of changes in the electrical properties of novel knitted conductive textiles during cyclic loading.

PubMed

Isaia, Cristina; McNally, Donal; McMaster, Simon A; Branson, David T

2016-08-01

Combining stainless steel with polyester fibres adds an attractive conductive behaviour to the yarn. Once knitted in such a manner, fabrics develop sensing properties that make the textiles, also known as e-textiles, suitable for smart/wearable applications. Structural deformations of the fibres (e.g. stretching) will cause changes in the conductivity of the fabric. This work investigates changes in the electrical properties exhibited by four knitted conductive textiles made of 20% stainless steel and 80% polyester fibres during cyclic loading. The samples were preconditioned first with 500 hundred cycles of unidirectional elongation and, after a rest interval, tested again for repeatability at the same conditions. In both cases the electrical behaviour stabilises after a few tens of cycles. In particular the repeatability test exhibited a considerably smaller settling time and a larger resistance due to the mechanical stabilisation and the loosening of the fabrics, respectively. It was found that the current provided to the fabrics affects the resistance measurements by decreasing the resistance value at which the samples become electrically stable. The reported findings present a valid method for the electrical characterisation of conductive textiles for use in further studies as a wearable technology.

Blooming Knit Flowers: Loop-Linked Soft Morphing Structures for Soft Robotics.

PubMed

Han, Min-Woo; Ahn, Sung-Hoon

2017-04-01

A loop-linked structure, which is capable of morphing in various modes, including volumetric transformation, is developed based on knitting methods. Morphing flowers (a lily-like, a daffodil-like, gamopetalous, and a calla-like flower) are fabricated using loop patterning, and their blooming motion is demonstrated by controlling a current that selectively actuates the flowers petals. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of Knitted Warm Garments from Speciality Jute Yarns

NASA Astrophysics Data System (ADS)

Roy, Alok Nath

2013-09-01

Jute-polyester blended core and textured polyester multifilament cover spun-wrapped yarn was produced using existing jute spinning machines. The spun-wrapped yarn so produced show a reduction in hairiness up to 86.1 %, improvement in specific work of rupture up to 9.8 % and specific flexural rigidity up to 23.6 % over ordinary jute-polyester blended yarn. The knitted swatch produced out of these spun-wrapped yarn using seven gauge and nine gauge needle in both single jersey and double jersey knitting machines showed very good dimensional stability even after three washing. The two-ply and three-ply yarn produced from single spun-wrapped yarn can be easily used in knitting machines and also in hand-knitting for the production of sweaters. The thermal insulation value of the sweaters produced with jute-polyester blended spun-wrapped yarn is comparable with thermal insulation value of sweaters made from 100 % acrylic and 100 % wool. However, the hand-knitted sweaters showed higher thermal insulation value than the machine-knitted sweaters due to less packing of yarn in hand knitted structure as compared to machine knitting.

The Effect of Stretching on Ultraviolet Protection of Cotton and Cotton/Coolmax-Blended Weft Knitted Fabric in a Dry State

PubMed Central

Kan, Chi-wai; Yam, Lim-yung; Ng, Sun-pui

2013-01-01

In this paper, the ultraviolet protection factor (UPF) of weft knitted fabrics made from 20Ne cotton yarn, Coolmax yarn and their blends in dry, relaxed and stretched states were studied. According to the fibre composition, samples were divided into three groups: Group I (single cotton yarn); Group II (cotton/cotton combination); and Group III (Coolmax/cotton combination) for discussion. In addition, yarn and fabric properties such as yarn tenacity, yarn strength, fibre combination and water vapour transmission that affect the corresponding UPF values are used for formulating a prediction model in order to determine UPF. Generally speaking, when samples are measured under stretched conditions in a dry state, they exhibit a remarkable reduction in ultraviolet protective power, as pores are opened up and UV radiation can easily penetrate through these pores. In addition, greater stretch percentage came along with greater reduction in UPF. This can be explained by the fact that the amount and the size of pores increase when samples are subjected to greater tension. PMID:28788371

Parametric modelling design applied to weft knitted surfaces and its effects in their physical properties

NASA Astrophysics Data System (ADS)

Oliveira, N. P.; Maciel, L.; Catarino, A. P.; Rocha, A. M.

2017-10-01

This work proposes the creation of models of surfaces using a parametric computer modelling software to obtain three-dimensional structures in weft knitted fabrics produced on single needle system machines. Digital prototyping, another feature of digital modelling software, was also explored in three-dimensional drawings generated using the Rhinoceros software. With this approach, different 3D structures were developed and produced. Physical characterization tests were then performed on the resulting 3D weft knitted structures to assess their ability to promote comfort. From the obtained results, it is apparent that the developed structures have potential for application in different market segments, such as clothing and interior textiles.

The research of knitting needle status monitoring setup

NASA Astrophysics Data System (ADS)

Liu, Lu; Liao, Xiao-qing; Zhu, Yong-kang; Yang, Wei; Zhang, Pei; Zhao, Yong-kai; Huang, Hui-jie

2013-09-01

In textile production, quality control and testing is the key to ensure the process and improve the efficiency. Defect of the knitting needles is the main factor affecting the quality of the appearance of textiles. Defect detection method based on machine vision and image processing technology is universal. This approach does not effectively identify the defect generated by damaged knitting needles and raise the alarm. We developed a knitting needle status monitoring setup using optical imaging, photoelectric detection and weak signal processing technology to achieve real-time monitoring of weaving needles' position. Depending on the shape of the knitting needle, we designed a kind of Glass Optical Fiber (GOF) light guides with a rectangular port used for transmission of the signal light. To be able to capture the signal of knitting needles accurately, we adopt a optical 4F system which has better imaging quality and simple structure and there is a rectangle image on the focal plane after the system. When a knitting needle passes through position of the rectangle image, the reflected light from needle surface will back to the GOF light guides along the same optical system. According to the intensity of signals, the computer control unit distinguish that the knitting needle is broken or curving. The experimental results show that this system can accurately detect the broken needles and the curving needles on the knitting machine in operating condition.

Knitting for heart valve tissue engineering

PubMed Central

Ayad, Nadia; Wojciechowska, Dorota; Zielińska, Dorota; Struszczyk, Marcin H.; Latif, Najma; Yacoub, Magdi

Knitting is a versatile technology which offers a large portfolio of products and solutions of interest in heart valve (HV) tissue engineering (TE). One of the main advantages of knitting is its ability to construct complex shapes and structures by precisely assembling the yarns in the desired position. With this in mind, knitting could be employed to construct a HV scaffold that closely resembles the authentic valve. This has the potential to reproduce the anisotropic structure that is characteristic of the heart valve with the yarns, in particular the 3-layered architecture of the leaflets. These yarns can provide oriented growth of cells lengthwise and consequently enable the deposition of extracellular matrix (ECM) proteins in an oriented manner. This technique, therefore, has a potential to provide a functional knitted scaffold, but to achieve that textile engineers need to gain a basic understanding of structural and mechanical aspects of the heart valve and in addition, tissue engineers must acquire the knowledge of tools and capacities that are essential in knitting technology. The aim of this review is to provide a platform to consolidate these two fields as well as to enable an efficient communication and cooperation among these two research areas. PMID:29043276

Knitted Strain Sensor Textiles of Highly Conductive All-Polymeric Fibers.

PubMed

Seyedin, Shayan; Razal, Joselito M; Innis, Peter C; Jeiranikhameneh, Ali; Beirne, Stephen; Wallace, Gordon G

2015-09-30

A scaled-up fiber wet-spinning production of electrically conductive and highly stretchable PU/PEDOT:PSS fibers is demonstrated for the first time. The PU/PEDOT:PSS fibers possess the mechanical properties appropriate for knitting various textile structures. The knitted textiles exhibit strain sensing properties that were dependent upon the number of PU/PEDOT:PSS fibers used in knitting. The knitted textiles show sensitivity (as measured by the gauge factor) that increases with the number of PU/PEDOT:PSS fibers deployed. A highly stable sensor response was observed when four PU/PEDOT:PSS fibers were co-knitted with a commercial Spandex yarn. The knitted textile sensor can distinguish different magnitudes of applied strain with cyclically repeatable sensor responses at applied strains of up to 160%. When used in conjunction with a commercial wireless transmitter, the knitted textile responded well to the magnitude of bending deformations, demonstrating potential for remote strain sensing applications. The feasibility of an all-polymeric knitted textile wearable strain sensor was demonstrated in a knee sleeve prototype with application in personal training and rehabilitation following injury.

Thermo-Mechanical Behavior of Textile Heating Fabric Based on Silver Coated Polymeric Yarn

PubMed Central

Hamdani, Syed Talha Ali; Potluri, Prasad; Fernando, Anura

2013-01-01

This paper presents a study conducted on the thermo-mechanical properties of knitted structures, the methods of manufacture, effect of contact pressure at the structural binding points, on the degree of heating. The test results also present the level of heating produced as a function of the separation between the supply terminals. The study further investigates the rate of heating and cooling of the knitted structures. The work also presents the decay of heating properties of the yarn due to overheating. Thermal images were taken to study the heat distribution over the surface of the knitted fabric. A tensile tester having constant rate of extension was used to stretch the fabric. The behavior of temperature profile of stretched fabric was observed. A comparison of heat generation by plain, rib and interlock structures was studied. It was observed from the series of experiments that there is a minimum threshold force of contact at binding points of a knitted structure is required to pass the electricity. Once this force is achieved, stretching the fabric does not affect the amount of heat produced. PMID:28809358

Aligned poly(L-lactic-co-e-caprolactone) electrospun microfibers and knitted structure: a novel composite scaffold for ligament tissue engineering.

PubMed

Vaquette, Cédryck; Kahn, Cyril; Frochot, Céline; Nouvel, Cécile; Six, Jean-Luc; De Isla, Natalia; Luo, Li-Hua; Cooper-White, Justin; Rahouadj, Rachid; Wang, Xiong

2010-09-15

We developed a novel technique involving knitting and electrospinning to fabricate a composite scaffold for ligament tissue engineering. Knitted structures were coated with poly(L-lactic-co-e-caprolactone) (PLCL) and then placed onto a rotating cylinder and a PLCL solution was electrospun onto the structure. Highly aligned 2-microm-diameter microfibers covered the space between the stitches and adhered to the knitted scaffolds. The stress-strain tensile curves exhibited an initial toe region similar to the tensile behavior of ligaments. Composite scaffolds had an elastic modulus (150 +/- 14 MPa) similar to the modulus of human ligaments. Biological evaluation showed that cells proliferated on the composite scaffolds and they spontaneously orientated along the direction of microfiber alignment. The microfiber architecture also induced a high level of extracellular matrix secretion, which was characterized by immunostaining. We found that cells produced collagen type I and type III, two main components found in ligaments. After 14 days of culture, collagen type III started to form a fibrous network. We fabricated a composite scaffold having the mechanical properties of the knitted structure and the morphological properties of the aligned microfibers. It is difficult to seed a highly macroporous structure with cells, however the technique we developed enabled an easy cell seeding due to presence of the microfiber layer. Therefore, these scaffolds presented attractive properties for a future use in bioreactors for ligament tissue engineering. (c) 2010 Wiley Periodicals, Inc.

Knitted Patterns as a Model for Anisotropy

ERIC Educational Resources Information Center

Cepic, Mojca

2012-01-01

Anisotropy is a difficult concept, although it is often met in everyday life. This paper describes a simple model--knitted patterns--having anisotropic elastic properties. The elastic constant is measured for the force applied in different directions with respect to the knitting direction. It is also shown that the deformation of the knitted…

The Knitting Lesson.

ERIC Educational Resources Information Center

Smith, Pamela

1987-01-01

Based on Jean-Francois Millet's 1869 painting, "The Knitting Lesson," this lesson's goal is to introduce students in grades seven through nine to genre (everyday life) painting the nineteenth century. The lesson is also designed to show that some aspects of genre may be timeless. (BSR)

Three-dimensionally deformable, highly stretchable, permeable, durable and washable fabric circuit boards.

PubMed

Li, Qiao; Tao, Xiao Ming

2014-11-08

This paper reports fabric circuit boards (FCBs), a new type of circuit boards, that are three-dimensionally deformable, highly stretchable, durable and washable ideally for wearable electronic applications. Fabricated by using computerized knitting technologies at ambient dry conditions, the resultant knitted FCBs exhibit outstanding electrical stability with less than 1% relative resistance change up to 300% strain in unidirectional tensile test or 150% membrane strain in three-dimensional ball punch test, extraordinary fatigue life of more than 1 000 000 loading cycles at 20% maximum strain, and satisfactory washing capability up to 30 times. To the best of our knowledge, the performance of new FCBs has far exceeded those of previously reported metal-coated elastomeric films or other organic materials in terms of changes in electrical resistance, stretchability, fatigue life and washing capability as well as permeability. Theoretical analysis and numerical simulation illustrate that the structural conversion of knitted fabrics is attributed to the effective mitigation of strain in the conductive metal fibres, hence the outstanding mechanical and electrical properties. Those distinctive features make the FCBs particularly suitable for next-to-skin electronic devices. This paper has further demonstrated the application potential of the knitted FCBs in smart protective apparel for in situ measurement during ballistic impact.

Three-dimensionally deformable, highly stretchable, permeable, durable and washable fabric circuit boards

PubMed Central

Li, Qiao; Tao, Xiao Ming

2014-01-01

This paper reports fabric circuit boards (FCBs), a new type of circuit boards, that are three-dimensionally deformable, highly stretchable, durable and washable ideally for wearable electronic applications. Fabricated by using computerized knitting technologies at ambient dry conditions, the resultant knitted FCBs exhibit outstanding electrical stability with less than 1% relative resistance change up to 300% strain in unidirectional tensile test or 150% membrane strain in three-dimensional ball punch test, extraordinary fatigue life of more than 1 000 000 loading cycles at 20% maximum strain, and satisfactory washing capability up to 30 times. To the best of our knowledge, the performance of new FCBs has far exceeded those of previously reported metal-coated elastomeric films or other organic materials in terms of changes in electrical resistance, stretchability, fatigue life and washing capability as well as permeability. Theoretical analysis and numerical simulation illustrate that the structural conversion of knitted fabrics is attributed to the effective mitigation of strain in the conductive metal fibres, hence the outstanding mechanical and electrical properties. Those distinctive features make the FCBs particularly suitable for next-to-skin electronic devices. This paper has further demonstrated the application potential of the knitted FCBs in smart protective apparel for in situ measurement during ballistic impact. PMID:25383032

Smarten up garments through knitting

NASA Astrophysics Data System (ADS)

Schwarz-Pfeiffer, A.; Obermann, M.; Weber, M. O.; Ehrmann, A.

2016-07-01

Smart textiles are a growing and fascinating field with enormous potential in the field of wearable electronics: shirts with integrated electrodes, socks stimulating the blood circulation or heating clothing are just a few examples of wearable, smart textile products. Most often, the technology of choice for on-the-body-worn smart textiles is knitting as it results in stretchable and, hence comfortable garments. This presentation explores the knitting technology in respect to smart textiles giving an overview of current research activities as well as commercially available products on the market. It further intends to foster the transfer of research approaches into business applications as well as to develop new challenging research ideas.

Knitted outer gloves in primary hip and knee arthroplasty.

PubMed

Tanner, J; Wraighte, P; Howard, P

2006-01-01

A randomised trial was carried out to determine the rate of perforation to inner gloves when comparing latex with knitted gloves during hip and knee arthroplasty. Members of the surgical team were randomised to wear either two pairs of latex gloves (standard double gloving) or a knitted glove on top of a latex glove. In addition, participants completed a visual analogue assessment of their overall satisfaction with the gloves. A total of 406 inner gloves were tested for perforations over a four-month period: 23% of inner gloves were perforated when latex outer gloves were used and 6% of inner gloves were perforated when knitted outer gloves were used. In total, there were 64 perforations to the inner gloves; only one of these perforations was detected by the glove wearer. Wearing knitted outer gloves during hip and knee arthroplasty statistically significantly reduces the risk of perforation to inner latex gloves (p<0.0001).

General View of Kinckley Knitting Mill site, east end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General View of Kinckley Knitting Mill site, east end of site along Wister Street, looking north, showing ruin of stone mill building and smoke stack of the Germantown Dyeworks in background - Hinckley Knitting Mills, 21-35 East Wister Street, Philadelphia, Philadelphia County, PA

A new design concept for knitted external vein-graft support mesh.

PubMed

Singh, Charanpreet; Wang, Xungai

2015-08-01

Autologous vein-graft failure significantly limits the long-term efficacy of coronary artery bypass procedures. The major cause behind this complication is biomechanical mismatch between the vein and coronary artery. The implanted vein experiences a sudden increase (10-12 fold) in luminal pressures. The resulting vein over-distension or 'ballooning' initiates wall thickening phenomenon and ultimate occlusion. Therefore, a primary goal in improving the longevity of a coronary bypass procedure is to inhibit vein over-distension using mechanical constriction. The idea of using an external vein-graft support mesh has demonstrated sustained benefits and wide acceptance in experimental studies. Nitinol based knitted structures have offered more promising mechanical features than other mesh designs owing to their unique loosely looped construction. However, the conventional plain knit construction still exhibits limitations (radial compliance, deployment ease, flexibility, and bending stresses) which limit this design from proving its real clinical advantage. The new knitted mesh design presented in this study is based on the concept of composite knitting utilising high modulus (nitinol and polyester) and low modulus (polyurethane) material components. The experimental comparison of the new design with a plain knit design demonstrated significant improvement in biomechanical (compliance, flexibility, extensibility, viscoelasticity) and procedural (deployment limit) parameters. The results are indicative of the promising role of new mesh in restoring the lost compliance and pulsatility of vein-graft at high arterial pressures. This way it can assist in controlled vein-graft remodelling and stepwise restoration of vein mechanical homoeostasis. Also, improvement in deployment limit parameter offers more flexibility for a surgeon to use a wide range of vein diameters, which may otherwise be rendered unusable for a plain knit mesh. Copyright © 2015 Elsevier Ltd. All rights

Flame retardant treatments of PBI fabric.

NASA Technical Reports Server (NTRS)

Temin, S. C.

1972-01-01

Fabrics knitted or woven from polybenzimidazole (PBI) fibers were treated to reduce flammability in oxygen atmospheres, particularly that of 5 psia oxygen. Bromination to approximately 15% weight gain of such fabrics led to markedly lower burning rates; samples brominated to over 80% weight gain were self-extinguishing in 5 psia oxygen. The loss in tensile strength of fabrics due to bromination was negligible although shrinkage was observed. Free fibers showed negligible losses on bromination. Treatment of PBI fabric with organophosphorus compounds also achieved self-extinguishing character in 5 psia oxygen but the enhanced flameproofing was largely lost on leaching. Reaction with POCl3 in pyridine led to a permanent reduction in flammability.

76 FR 30394 - St. John Knits, Inc. Irvine, CA; Amended Certification Regarding Eligibility To Apply for Worker...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-25

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,839] St. John Knits, Inc..., 2011, applicable to workers of St. John Knits, Inc., Irvine, California. The workers are engaged in the... adjustment assistance was issued for all workers of St. John Knits, Sample Manufacturing Department, Irvine...

76 FR 16447 - St. John Knits, Inc., Irvine, CA; Amended Certification Regarding Eligibility To Apply for Worker...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-23

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,839] St. John Knits, Inc..., 2011, applicable to workers of St. John Knits, Inc., Irvine, California. The workers are engaged in the... adjustment assistance was issued for all workers of St. John Knits, Sample Manufacturing Department, Irvine...

Experimental investigation of active rib stitch knitted architecture for flow control applications

NASA Astrophysics Data System (ADS)

Abel, Julianna M.; Mane, Poorna; Pascoe, Benjamin; Luntz, Jonathan; Brei, Diann

2010-04-01

Actively manipulating flow characteristics around the wing can enhance the high-lift capability and reduce drag; thereby, increasing fuel economy, improving maneuverability and operation over diverse flight conditions which enables longer, more varied missions. Active knits, a novel class of cellular structural smart material actuator architectures created by continuous, interlocked loops of stranded active material, produce distributed actuation that can actively manipulate the local surface of the aircraft wing to improve flow characteristics. Rib stitch active knits actuate normal to the surface, producing span-wise discrete periodic arrays that can withstand aerodynamic forces while supplying the necessary displacement for flow control. This paper presents a preliminary experimental investigation of the pressuredisplacement actuation performance capabilities of a rib stitch active knit based upon shape memory alloy (SMA) wire. SMA rib stitch prototypes in both individual form and in stacked and nestled architectures were experimentally tested for their quasi-static load-displacement characteristics, verifying the parallel and series relationships of the architectural configurations. The various configurations tested demonstrated the potential of active knits to generate the required level of distributed surface displacements while under aerodynamic level loads for various forms of flow control.

Needle bar for warp knitting machines

DOEpatents

Hagel, Adolf; Thumling, Manfred

1979-01-01

Needle bar for warp knitting machines with a number of needles individually set into slits of the bar and having shafts cranked to such an extent that the head section of each needle is in alignment with the shaft section accommodated by the slit. Slackening of the needles will thus not influence the needle spacing.

Knitting as an Aesthetic of Civic Engagement: Re-Conceptualizing Feminist Pedagogy through Touch

ERIC Educational Resources Information Center

Springgay, Stephanie

2010-01-01

Everyone is in the midst of an explosion in the popularity of knitting. Shifting the traditional stereotype of what a knitter should be, the youth of today have taken up knitting as a tactile and embodied form of connectivity. In a rapidly changing and unpredictable world, characterized by, among other factors, the unprecedented expansion of…

An infiltration/cure model for manufacture of fabric composites by the resin infusion process

NASA Technical Reports Server (NTRS)

Weideman, Mark H.; Loos, Alfred C.; Dexter, H. Benson; Hasko, Gregory H.

1992-01-01

A 1-D infiltration/cure model was developed to simulate fabrication of advanced textile composites by the resin film infusion process. The simulation model relates the applied temperature and pressure processing cycles, along with the experimentally measured compaction and permeability characteristics of the fabric preforms, to the temperature distribution, the resin degree of cure and viscosity, and the infiltration flow front position as a function of time. The model also predicts the final panel thickness, fiber volume fraction, and resin mass for full saturation as a function of compaction pressure. Composite panels were fabricated using the RTM (Resin Transfer Molding) film infusion technique from knitted, knitted/stitched, and 2-D woven carbon preforms and Hercules 3501-6 resin. Fabric composites were fabricated at different compaction pressures and temperature cycles to determine the effects of the processing on the properties. The composites were C-scanned and micrographed to determine the quality of each panel. Advanced cure cycles, developed from the RTM simulation model, were used to reduce the total cure cycle times by a factor of 3 and the total infiltration times by a factor of 2.

Knitting Mochilas: A Sociocultural, Developmental Practice in Arhuaco Indigenous Communities

PubMed Central

Rodríguez-Burgos, Lilian Patricia; Rodríguez-Castro, Jennifer; Bojacá-Rodríguez, Sandra Milena; Izquierdo-Martínez, Dwrya Elena; Amórtegui-Lozano, Allain Alexander; Prieto-Castellanos, Miguel Angel

2016-01-01

The purpose of this article is to analyze the psycho-cultural processes involved in knitting “mochilas” (traditional bags), a common craft in the Arhuaco indigenous community located in the Sierra Nevada de Santa Marta, Colombia. The article is structured in three parts, as follows: first, issues related to child development are discussed; then, the analysis method used to study the processes involved in the practice of knitting is presented and, finally, we reflect on the importance of recovering the sense and meaning of this everyday practice as a way to study child development. PMID:27298634

Preparation of collagen/polyurethane/knitted silk as a composite scaffold for tendon tissue engineering.

PubMed

Sharifi-Aghdam, Maryam; Faridi-Majidi, Reza; Derakhshan, Mohammad Ali; Chegeni, Arash; Azami, Mahmoud

2017-07-01

The main objective of this study was to prepare a hybrid three-dimensional scaffold that mimics natural tendon tissues. It has been found that a knitted silk shows good mechanical strength; however, cell growth on the bare silk is not desirable. Hence, electrospun collagen/polyurethane combination was used to cover knitted silk. A series of collagen and polyurethane solutions (4%-7% w/v) in aqueous acetic acid were prepared and electrospun. According to obtained scanning electron microscopy images from pure collagen and polyurethane nanofibers, concentration was set constant at 5% (w/v) for blend solutions of collagen/polyurethane. Afterward, blend solutions with the weight ratios of 75/25, 50/50 and 25/75 were electrospun. Scanning electron microscopy images demonstrated the smooth and uniform morphology for the optimized nanofibers. The least fibers diameter among three weight ratios was found for collagen/polyurethane (25/75) which was 100.86 ± 40 nm and therefore was selected to be electrospun on the knitted silk. Attenuated total reflectance-Fourier transform infrared spectra confirmed the chemical composition of obtained electrospun nanofibers on the knitted silk. Tensile test of the specimens including blend nanofiber, knitted silk and commercial tendon substitute examined and indicated that collagen/polyurethane-coated knitted silk has appropriate mechanical properties as a scaffold for tendon tissue engineering. Then, Alamar Blue assay of the L929 fibroblast cell line seeded on the prepared scaffolds demonstrated appropriate viability of the cells with a significant proliferation on the scaffold containing more collagen content. The results illustrate that the designed structure would be promising for being used as a temporary substitute for tendon repair.

Comfort and microbial barrier properties of garments worn next to the skin

NASA Astrophysics Data System (ADS)

Kopitar, D.; Rogina-Car, B.; Skenderi, Z.

2017-10-01

Compared with viscose fibre, modal fibre is characterized by some advantageous properties such as higher dry and wet tenacities, higher wet modulus, lower water retention capacity and lower level of swelling. Impact of different knitted fabric structure made of cotton and 97 % CMD/3 % EL fibres on thermo-physiological comfort and microbial barrier properties were investigated. All knitted fabrics have very good physiological properties. The microbial barrier permeability of knitted fabric after extreme contamination with bacterial spores in dry state showed that double jersey offered more effective microbial barrier than the single jersey knitted fabrics respectively the greater thickness of double jersey knitted fabric provide more difficult barrier to bacterial spores to pass. In wet state all knitted fabrics have more effective microbial barrier which could be explained by cellulose fibres swelling. In wet state 97 % CMD/3 % EL single jersey knitted fabric have more effective microbial barrier then cotton double and single jersey knitted fabrics.

40 CFR 410.54 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Pretreatment standards for existing sources (PSES). 410.54 Section 410.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory...

40 CFR 410.56 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Pretreatment standards for new sources (PSNS). 410.56 Section 410.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory...

40 CFR 410.54 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for existing sources (PSES). 410.54 Section 410.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory...

40 CFR 410.56 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for new sources (PSNS). 410.56 Section 410.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory...

The hydroentanglement system of producing nonwoven fabrics of certain specific attributes and functionalities

USDA-ARS?s Scientific Manuscript database

Although the traditional technologies and processes of producing fabric structures, via yarn spinning, weaving, knitting, lacing, tufting, or the like, continue to be the ‘major league’ players in textile manufacturing today, the modern hydroentanglement system, commonly known as “spunlacing,” has a...

Study on magnetic force of electromagnetic levitation circular knitting machine

NASA Astrophysics Data System (ADS)

Wu, X. G.; Zhang, C.; Xu, X. S.; Zhang, J. G.; Yan, N.; Zhang, G. Z.

2018-06-01

The structure of the driving coil and the electromagnetic force of the test prototype of electromagnetic-levitation (EL) circular knitting machine are studied. In this paper, the driving coil’s structure and working principle of the EL circular knitting machine are firstly introduced, then the mathematical modelling analysis of the driving electromagnetic force is carried out, and through the Ansoft Maxwell finite element simulation software the coil’s magnetic induction intensity and the needle’s electromagnetic force is simulated, finally an experimental platform is built to measure the coil’s magnetic induction intensity and the needle’s electromagnetic force. The results show that the theoretical analysis, the simulation analysis and the results of the test are very close, which proves the correctness of the proposed model.

40 CFR 410.55 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true New source performance standards (NSPS). 410.55 Section 410.55 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory § 410.55 New...

40 CFR 410.55 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true New source performance standards (NSPS). 410.55 Section 410.55 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory § 410.55 New...

19 CFR 10.244 - Certificate of Origin.

Code of Federal Regulations, 2011 CFR

2011-04-01

... assembled from U.S. formed, dyed, printed and finished fabrics or fabric components, or U.S. formed knit-to... llama, alpaca or vicuña fabrics, fabric components, or knit-to-shape components, from Andean yarns 10... more yarns, fabrics, fabric components, or knit-to-shape components described in preference groups A...

19 CFR 10.244 - Certificate of Origin.

Code of Federal Regulations, 2010 CFR

2010-04-01

... assembled from U.S. formed, dyed, printed and finished fabrics or fabric components, or U.S. formed knit-to... llama, alpaca or vicuña fabrics, fabric components, or knit-to-shape components, from Andean yarns 10... more yarns, fabrics, fabric components, or knit-to-shape components described in preference groups A...

Heat sealable, flame and abrasion resistant coated fabric

NASA Technical Reports Server (NTRS)

Tschirch, R. P.; Sidman, K. R. (Inventor)

1983-01-01

Flame retardant, abrasion resistant elastomeric compositions are disclosed which are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Heat sealable coated fabrics employing such elastomeric compositions as coating film are produced by dissolving the elastomeric composition to form a solution, casting the solution onto a release paper and drying it to form an elastomeric film. The film is then bonded to a woven, knitted, or felted fabric.

Evaluating the effect of spinning systems on thermal comfort properties of modal fabrics

NASA Astrophysics Data System (ADS)

Seçil Aydın, İ.; Kertmen, M.; Marmarali, A.

2017-10-01

In recent years the importance of clothing comfort became one of the most important feature of the fabrics. The aim of this study is to characterize thermal comfort properties of single jersey fabrics were knitted using 100% modal yarns which were spun in various types of yarn spinning methods such as ring spinning, compact spinning, rotor spinning and airjet spinning. Thermal comfort properties like air permeability, thermal resistance, thermal absorptivity and water vapour permeability of fabrics were tested. The results indicate that compact spinning technology will be appropriate for the summer climate casual wear.

A two-dimensional analytical model and experimental validation of garter stitch knitted shape memory alloy actuator architecture

NASA Astrophysics Data System (ADS)

Abel, Julianna; Luntz, Jonathan; Brei, Diann

2012-08-01

Active knits are a unique architectural approach to meeting emerging smart structure needs for distributed high strain actuation with simultaneous force generation. This paper presents an analytical state-based model for predicting the actuation response of a shape memory alloy (SMA) garter knit textile. Garter knits generate significant contraction against moderate to large loads when heated, due to the continuous interlocked network of loops of SMA wire. For this knit architecture, the states of operation are defined on the basis of the thermal and mechanical loading of the textile, the resulting phase change of the SMA, and the load path followed to that state. Transitions between these operational states induce either stick or slip frictional forces depending upon the state and path, which affect the actuation response. A load-extension model of the textile is derived for each operational state using elastica theory and Euler-Bernoulli beam bending for the large deformations within a loop of wire based on the stress-strain behavior of the SMA material. This provides kinematic and kinetic relations which scale to form analytical transcendental expressions for the net actuation motion against an external load. This model was validated experimentally for an SMA garter knit textile over a range of applied forces with good correlation for both the load-extension behavior in each state as well as the net motion produced during the actuation cycle (250% recoverable strain and over 50% actuation). The two-dimensional analytical model of the garter stitch active knit provides the ability to predict the kinetic actuation performance, providing the basis for the design and synthesis of large stroke, large force distributed actuators that employ this novel architecture.

Social Interactions and Learning in an Informal Setting: An Ethnography of Communication in a Knitting Circle.

ERIC Educational Resources Information Center

Jacobson, Anna

This paper describes a study of a speech community, a group of approximately 10 women, aged 25 to 65, who met at least 3 times a month to knit, drink coffee, and chat. The paper notes that knitting circles have survived through history because they serve a social function that surpasses historical events--they are communities that co-construct the…

Design for Health and Well Being: Knitted Products for Diabetics

NASA Astrophysics Data System (ADS)

Gault, A.

2016-07-01

This paper will discuss the design development, manufacturing and testing of knitted products maximizing the use of new innovations in Nano- technology and the integration of Phase Changing Materials specifically for diabetics. The project identified key aspects requiring design solutions to bring improvement to the circulatory problems with specific reference to the diabetic condition. Diabetics have particular difficulty in regulating their body temperature and this can result in the condition worsening, and resulting in loss of digits or limbs. The design of products to prevent the deterioration of the diabetic condition and to help those with limb loss was developed in collaboration with a Northern Ireland diabetic consultant, a product engineer and a knitwear designer. The fusion of ideas between the stakeholders resulted in the development and manufacture of a range of products that have been successfully tested at the yarn and fabric development stage and have been proven to maintain body temperature by either cooling or warming and therefore bring improvement to health and well-being. Whilst the product has a performance element the design ideas created desirable products that not only provided solutions to the brief but also resulted in products that had further market applications.

78 FR 7414 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... Agreements (``CITA'') has determined that certain cotton/polyester three-thread circular knit fleece fabric... behalf of Intradeco Apparel, Inc. for certain cotton/polyester three-thread circular knit fleece fabric.... Specifications: Certain Cotton/Polyester Three-Thread Circular Knit Fleece Fabric HTS: 6001.21 Fiber content...

Finite element analysis of the stiffness of fabric reinforced composites

NASA Technical Reports Server (NTRS)

Foye, R. L.

1992-01-01

The objective of this work is the prediction of all three dimensional elastic moduli of textile fabric reinforced composites. The analysis is general enough for use with complex reinforcing geometries and capable of subsequent improvements. It places no restrictions on fabric microgeometry except that the unit cell be determinate and rectangular. The unit cell is divided into rectangular subcells in which the reinforcing geometries are easier to define and analyze. The analysis, based on inhomogeneous finite elements, is applied to a variety of weave, braid, and knit reinforced composites. Some of these predictions are correlated to test data.

Comfort Characterization of Various Fabrics for Extremity Protection

DTIC Science & Technology

2013-09-01

comfort, permeability, drape , stretch 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 48 19a. NAME OF...such as fabric “ drape ” (i.e., the ability to conform to a surface), which is thought to be a function of bending and in-plane shear stiffness (2...test (17), Kawabata tests (18), and the Cusick drape test (19). In general, knits appear to provide the best combination of breathability and ease of

16 CFR 1609.1 - Text of the Flammable Fabrics Act of 1953, as amended in 1954.

Code of Federal Regulations, 2014 CFR

2014-01-01

... be worn by individuals except hats, gloves, and footwear: Provided, however, That such hats do not... form an integral part of another garment: And provided further, That such footwear does not consist of...) The term fabric means any material (other than fiber, filament, or yarn) woven, knitted, felted, or...

16 CFR 1609.1 - Text of the Flammable Fabrics Act of 1953, as amended in 1954.

Code of Federal Regulations, 2012 CFR

2012-01-01

... be worn by individuals except hats, gloves, and footwear: Provided, however, That such hats do not... form an integral part of another garment: And provided further, That such footwear does not consist of...) The term fabric means any material (other than fiber, filament, or yarn) woven, knitted, felted, or...

Effects of wearing knitted or rubber gloves on the transfer of Escherichia cohi between hands and meat.

PubMed

Gill, C O; Jones, T

2002-06-01

On eight occasions, five volunteers each handled five pieces of meat with bare hands or while wearing dry or wet knitted gloves or rubber gloves after hands had been inoculated with Escherichia coli or after handling a piece of meat inoculated with E. coli. On each occasion, after all meat was handled, each piece of meat, glove, and hand were sampled to recover E. coli. When hands were inoculated, E. coli was recovered from all meat handled with bare hands, in lesser numbers from some pieces handled with knitted gloves, and from only one piece handled with rubber gloves. When pieces of inoculated meat were handled, the numbers of E. coli transferred to uninoculated meat from bare hands or rubber gloves decreased substantially with each successive piece of uninoculated meat, but decreases were small with knitted gloves. The findings indicate that, compared with bare hands, the use of knitted gloves could reduce the transfer of bacteria from hands to meat but could increase the transfer of bacteria between meat pieces, whereas the use of rubber gloves could largely prevent the first and greatly reduce the second type of bacteria transfer.

Fabric strain sensor integrated with CNPECs for repeated large deformation

NASA Astrophysics Data System (ADS)

Yi, Weijing

Flexible and soft strain sensors that can be used in smart textiles for wearable applications are much desired. They should meet the requirements of low modulus, large working range and good fatigue resistance as well as good sensing performances. However, there were no commercial products available and the objective of the thesis is to investigate fabric strain sensors based on carbon nanoparticle (CNP) filled elastomer composites (CNPECs) for potential wearing applications. Conductive CNPECs were fabricated and investigated. The introduction of silicone oil (SO) significantly decreased modulus of the composites to less than 1 MPa without affecting their deformability and they showed good stability after heat treatment. With increase of CNP concentration, a percolation appeared in electrical resistivity and the composites can be divided into three ranges. I-V curves and impedance spectra together with electro-mechanical studies demonstrated a balance between sensitivity and working range for the composites with CNP concentrations in post percolation range, and were preferred for sensing applications only if the fatigue life was improved. Due to the good elasticity and failure resist property of knitted fabric under repeated extension, it was adopted as substrate to increase the fatigue life of the conductive composites. After optimization of processing parameters, the conductive fabric with CNP concentration of 9.0CNP showed linear I-V curves when voltage is in the range of -1 V/mm and 1 V/mm and negligible capacitive behavior when frequency below 103 Hz even with strain of 60%. It showed higher sensitivity due to the combination of nonlinear resistance-strain behavior of the CNPECs and non-even strain distribution of knitted fabric under extension. The fatigue life of the conductive fabric was greatly improved. Extended on the studies of CNPECs and the coated conductive fabrics, a fabric strain sensor was designed, fabricated and packaged. The Young's modulus of

Systematic investigation of drip stains on apparel fabrics: The effects of prior-laundering, fibre content and fabric structure on final stain appearance.

PubMed

de Castro, Therese C; Taylor, Michael C; Kieser, Jules A; Carr, Debra J; Duncan, W

2015-05-01

Bloodstain pattern analysis is the investigation of blood deposited at crime scenes and the interpretation of that pattern. The surface that the blood gets deposited onto could distort the appearance of the bloodstain. The interaction of blood and apparel fabrics is in its infancy, but the interaction of liquids and apparel fabrics has been well documented and investigated in the field of textile science (e.g. the processes of wetting and wicking of fluids on fibres, yarns and fabrics). A systematic study on the final appearance of drip stains on torso apparel fabrics (100% cotton plain woven, 100% polyester plain woven, blend of polyester and cotton plain woven and 100% cotton single jersey knit) that had been laundered for six, 26 and 52 cycles prior to testing was investigated in the paper. The relationship between drop velocity (1.66±0.50m/s, 4.07±0.03m/s, 5.34±0.18m/s) and the stain characteristics (parent stain area, axes 1 and 2 and number of satellite stains) for each fabric was examined using analysis of variance. The experimental design and effect of storing blood were investigated on a reference sample, which indicated that the day (up to five days) at which the drops were generated did not affect the bloodstain. The effect of prior-laundering (six, 26 and 52 laundering cycles), fibre content (cotton vs. polyester vs. blend) and fabric structure (plain woven vs. single jersey knit) on the final appearance of the bloodstain were investigated. Distortion in the bloodstains produced on non-laundered fabrics indicated the importance of laundering fabrics to remove finishing treatments before conducting bloodstain experiments. For laundered fabrics, both the cotton fabrics and the blend had a circular to oval stain appearance, while the polyester fabric had a circular appearance with evidence of spread along the warp and weft yarns, which resulted in square-like stains at the lowest drop velocity. A significant (p<0.001) increase in the stain size on

19 CFR 10.850 - Verification of claim for duty-free treatment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... yarn, fabric, fabric components, and knit-to-shape components that were used in the production of the..., fabric, fabric components and knit-to-shape components. The affidavit or statement of origin should...

Interpreting the formation of bloodstains on selected apparel fabrics.

PubMed

de Castro, Therese; Nickson, Tania; Carr, Debra; Knock, Clare

2013-01-01

Bloodstain pattern analysis (BPA) is the investigation and interpretation of blood deposited at crime scenes. However, the interaction of blood and apparel fabrics has not been widely studied. In this work, the development of bloodstains (passive, absorbed and transferred) dropped from three different heights (500, 1,000, 1,500 mm) on two cotton apparel fabrics (1 × 1 rib knit, drill) was investigated. High-speed video was used to investigate the interaction of the blood and fabric at impact. The effect of drop height on the development of passive, absorbed and transferred bloodstains was investigated using image analysis and statistical tools. Visually, the passive bloodstain patterns produced on the technical face of fabrics from the different drop heights were similar. The blood soaked unequally through to the technical rear of both fabrics. Very little blood was transferred between a bloody fabric and a second piece of fabric. Statistically, drop height did not affect the size of the parent bloodstain (wet or dry), but did affect the number of satellite bloodstains formed. Some differences between the two fabrics were noted, therefore fabric structure and properties must be considered when conducting BPA on apparel fabrics.

Effect of fabric mounting method and backing material on bloodstain patterns of drip stains on textiles.

PubMed

Chang, J Y M; Michielsen, S

2016-05-01

Textiles may provide valuable bloodstain evidence to help piece together events or activities at violent crime scenes. However, in spite of over 75 years of research, there are still difficulties encountered in many cases in the interpretation and identification of bloodstains on textiles. In this study, we dripped porcine blood onto three types of fabric (plain woven, single jersey knit, and denim) that are supported in four different ways (hard, taut, loose, and semi-hard, i.e., fabric laid on denim). These four mounting methods represent different ways in which a textile may be present when blood from a violent act lands on it. This study investigates how the fabric mounting method and backing material affect the appearance of drip stains on textiles. We found that bloodstain patterns formed on fabric lying flat on a hard surface were very different from when the same fabric was suspended loosely. We also found that bloodstains formed on the technical back of single jersey knit were vastly different from those on the technical face. Interestingly, some drip stains showed blood passing through the textile and leaving a stain behind it that resembled insect stains. By observing, recording, and describing how a blood stained textile is found or presented at the scene, the analyst may be able to better understand bloodstains and bloodstain patterns on textiles, which could be useful to confirm or refute a witness's account of how blood came to be where it was found after a bloodshed event.

"Knitting Nannas" and "Frackman": A Gender Analysis of Australian Anti-Coal Seam Gas Documentaries (CSG) and Implications for Environmental Adult Education

ERIC Educational Resources Information Center

Larri, Larraine J.; Newlands, Maxine

2017-01-01

"Frackman" ("FM") and "Knitting Nannas" ("KN") are two documentaries about the anti-coal seam gas movement in Australia. "Frackman" features a former construction worker turned eco-activist, Dayne Pratzky (DP), fighting coal seam gas extraction. "Knitting Nannas" follows a group of women…

Factors Affecting the Persistence of Staphylococcus aureus on Fabrics

PubMed Central

Wilkoff, Lee J.; Westbrook, Louise; Dixon, Glen J.

1969-01-01

The persistence of Staphylococcus aureus (Smith) on wool blanket, wool gabardine, cotton sheeting, cotton knit jersey, cotton terry cloth, and cotton wash-and-wear fabrics was studied. The fabrics were exposed to bacterial populations by three methods: direct contact, aerosol, and a lyophilized mixture of bacteria and dust having a high content of textile fibers. The contaminated fabrics were held in 35 or 78% relative humidities at 25 C. In general, the persistence time of S. aureus populations on fabrics held in 35% relative humidity was substantially longer when the fabrics were contaminated by exposure to aerosolized cultures or to dust containing bacteria than when contaminated by direct contact. In a 78% relative humidity, bacterial populations on the fabrics persisted for substantially shorter periods of time regardless of the mode of contamination or fabric type. Cotton wash-and-wear fabric (treated with a modified triazone resin) was the material on which populations of S. aureus persisted for the shortest time. This organism retained its virulence for Swiss mice after being recovered from wool gabardine swatches held 4 weeks in 35% relative humidity and 6 weeks in 78% relative humidity. Images PMID:5775911

76 FR 67424 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-01

... Agreements (``CITA'') has determined that certain cotton/nylon/spandex raschel knit open work crepe fabric..., Travis & Rosenberg, P.A., on behalf of Hansae Co. Ltd., for certain cotton/nylon/spandex raschel knit... Availability proceedings. Specifications: Certain Cotton/Nylon/Spandex Raschel Knit Open Work Crepe Fabric HTS...

Modeling and testing of a knitted-sleeve fluidic artificial muscle

NASA Astrophysics Data System (ADS)

Ball, Erick J.; Meller, Michael A.; Chipka, Jordan B.; Garcia, Ephrahim

2016-11-01

The knitted-sleeve fluidic muscle is similar in design to a traditional McKibben muscle, with a separate bladder and sleeve. However, in place of a braided sleeve, it uses a tubular-knit sleeve made from a thin strand of flexible but inextensible yarn. When the bladder is pressurized, the sleeve expands by letting the loops of fiber slide past each other, changing the dimensions of the rectangular cells in the stitch pattern. Ideally, the internal volume of the sleeve would reach a maximum when its length has contracted by 2/3 from its maximum length, and although this is not reachable in practice, preliminary tests show that free contraction greater than 50% is achievable. The motion relies on using a fiber with a low coefficient of friction in order to reduce hysteresis to an acceptable level. In addition to increased stroke length, potential advantages of this technique include slower force drop-off during the stroke, more useable energy in certain applications, and greater similarity to the force-length relationship of skeletal muscle. Its main limitation is its potentially greater effect from friction compared to other fluidic muscle designs.

Effect of Plasma Treatment on Air and Water-Vapor Permeability of Bamboo Knitted Fabric

NASA Astrophysics Data System (ADS)

Prakash, C.; Ramakrishnan, G.; Chinnadurai, S.; Vignesh, S.; Senthilkumar, M.

2013-11-01

In this paper, the effects of oxygen and atmospheric plasma on air and water-vapor permeability properties of single jersey bamboo fabric have been investigated. The changes in these properties are believed to be related closely to the inter-fiber and inter-yarn friction force induced by the plasma treatments. The outcomes showed that the water-vapor permeability increased, although the air permeability decreased along with the plasma treatments. The SEM images clearly showed that the plasma modified the fiber surface outwardly. The results showed that the atmospheric plasma has an etching effect and increases the functionality of a bamboo surface, which is evident from SEM and FTIR-ATR analysis. These results reveal that atmospheric pressure plasma treatment is an effective method to improve the performance of bamboo fabric. Statistical analysis also indicates that the results are significant for air permeability and water-vapor permeability of the plasma-treated bamboo fabric.

Knitting Teacher: A Narrative Inquiry of a Researcher Who Has Been Researched

ERIC Educational Resources Information Center

Heydon, Rachel

2010-01-01

From the vantages of a teacher who has been researched and an educational researcher who has researched teachers, this inquiry constructs a knitted narrative from journals, letters, and stories written about my time teaching English studies in a remote First Nations' community and articles written about me when I was a research participant in a…

Screen printing of a capacitive cantilever-based motion sensor on fabric using a novel sacrificial layer process for smart fabric applications

NASA Astrophysics Data System (ADS)

Wei, Yang; Torah, Russel; Yang, Kai; Beeby, Steve; Tudor, John

2013-07-01

Free-standing cantilevers have been fabricated by screen printing sacrificial and structural layers onto a standard polyester cotton fabric. By printing additional conductive layers, a complete capacitive motion sensor on fabric using only screen printing has been fabricated. This type of free-standing structure cannot currently be fabricated using conventional fabric manufacturing processes. In addition, compared to conventional smart fabric fabrication processes (e.g. weaving and knitting), screen printing offers the advantages of geometric design flexibility and the ability to simultaneously print multiple devices of the same or different designs. Furthermore, a range of active inks exists from the printed electronics industry which can potentially be applied to create many types of smart fabric. Four cantilevers with different lengths have been printed on fabric using a five-layer structure with a sacrificial material underneath the cantilever. The sacrificial layer is subsequently removed at 160 °C for 30 min to achieve a freestanding cantilever above the fabric. Two silver electrodes, one on top of the cantilever and the other on top of the fabric, are used to capacitively detect the movement of the cantilever. In this way, an entirely printed motion sensor is produced on a standard fabric. The motion sensor was initially tested on an electromechanical shaker rig at a low frequency range to examine the linearity and the sensitivity of each design. Then, these sensors were individually attached to a moving human forearm to evaluate more representative results. A commercial accelerometer (Microstrain G-link) was mounted alongside for comparison. The printed sensors have a similar motion response to the commercial accelerometer, demonstrating the potential of a printed smart fabric motion sensor for use in intelligent clothing applications.

Flow Charts for Determining Your Requirements: Nine Metal Fabrication and Finishing Source Categories Area Sources National Emission Standards for Hazardous Air Pollutants (NESHAP) Subpart XXXXXX

EPA Pesticide Factsheets

This page contains a July 2008 document that has flow charts to help determine if this National Emission Standards for Hazardous Air Pollutants (NESHAP) rule for Nine metal Fabrication and Finishing Area Source Categories applies to your facility.

A knitted garment using intarsia technique for Heart Rate Variability biofeedback: Evaluation of initial prototype.

PubMed

Abtahi, F; Ji, G; Lu, K; Rödby, K; Seoane, F

2015-01-01

Heart rate variability (HRV) biofeedback is a method based on paced breathing at specific rate called resonance frequency by giving online feedbacks from user respiration and its effect on HRV. Since the HRV is also influence by different factors like stress and emotions, stress related to an unfamiliar measurement device, cables and skin electrodes may cover the underling effect of such kind of intervention. Wearable systems are usually considered as intuitive solutions which are more familiar to the end-user and can help to improve usability and hence reducing the stress. In this work, a prototype of a knitted garment using intarsia technique is developed and evaluated. Results show the satisfactory level of quality for Electrocardiogram and thoracic electrical bioimpedance i.e. for respiration monitoring as a part of HRV biofeedback system. Using intarsia technique and conductive yarn for making the connection instead of cables will reduce the complexity of fabrication in textile production and hence reduce the final costs in a final commercial product. Further development of garment and Android application is ongoing and usability and efficiency of final prototype will be evaluated in detail.

Emergence of scale-free close-knit friendship structure in online social networks.

PubMed

Cui, Ai-Xiang; Zhang, Zi-Ke; Tang, Ming; Hui, Pak Ming; Fu, Yan

2012-01-01

Although the structural properties of online social networks have attracted much attention, the properties of the close-knit friendship structures remain an important question. Here, we mainly focus on how these mesoscale structures are affected by the local and global structural properties. Analyzing the data of four large-scale online social networks reveals several common structural properties. It is found that not only the local structures given by the indegree, outdegree, and reciprocal degree distributions follow a similar scaling behavior, the mesoscale structures represented by the distributions of close-knit friendship structures also exhibit a similar scaling law. The degree correlation is very weak over a wide range of the degrees. We propose a simple directed network model that captures the observed properties. The model incorporates two mechanisms: reciprocation and preferential attachment. Through rate equation analysis of our model, the local-scale and mesoscale structural properties are derived. In the local-scale, the same scaling behavior of indegree and outdegree distributions stems from indegree and outdegree of nodes both growing as the same function of the introduction time, and the reciprocal degree distribution also shows the same power-law due to the linear relationship between the reciprocal degree and in/outdegree of nodes. In the mesoscale, the distributions of four closed triples representing close-knit friendship structures are found to exhibit identical power-laws, a behavior attributed to the negligible degree correlations. Intriguingly, all the power-law exponents of the distributions in the local-scale and mesoscale depend only on one global parameter, the mean in/outdegree, while both the mean in/outdegree and the reciprocity together determine the ratio of the reciprocal degree of a node to its in/outdegree. Structural properties of numerical simulated networks are analyzed and compared with each of the four real networks. This

Emergence of Scale-Free Close-Knit Friendship Structure in Online Social Networks

PubMed Central

Cui, Ai-Xiang; Zhang, Zi-Ke; Tang, Ming; Hui, Pak Ming; Fu, Yan

2012-01-01

Although the structural properties of online social networks have attracted much attention, the properties of the close-knit friendship structures remain an important question. Here, we mainly focus on how these mesoscale structures are affected by the local and global structural properties. Analyzing the data of four large-scale online social networks reveals several common structural properties. It is found that not only the local structures given by the indegree, outdegree, and reciprocal degree distributions follow a similar scaling behavior, the mesoscale structures represented by the distributions of close-knit friendship structures also exhibit a similar scaling law. The degree correlation is very weak over a wide range of the degrees. We propose a simple directed network model that captures the observed properties. The model incorporates two mechanisms: reciprocation and preferential attachment. Through rate equation analysis of our model, the local-scale and mesoscale structural properties are derived. In the local-scale, the same scaling behavior of indegree and outdegree distributions stems from indegree and outdegree of nodes both growing as the same function of the introduction time, and the reciprocal degree distribution also shows the same power-law due to the linear relationship between the reciprocal degree and in/outdegree of nodes. In the mesoscale, the distributions of four closed triples representing close-knit friendship structures are found to exhibit identical power-laws, a behavior attributed to the negligible degree correlations. Intriguingly, all the power-law exponents of the distributions in the local-scale and mesoscale depend only on one global parameter, the mean in/outdegree, while both the mean in/outdegree and the reciprocity together determine the ratio of the reciprocal degree of a node to its in/outdegree. Structural properties of numerical simulated networks are analyzed and compared with each of the four real networks. This

Note from North America: "Linda, VA AG 2013 and Knitting Needles" and "Words"

ERIC Educational Resources Information Center

Alper, Paul

2014-01-01

This article is comprised of two essays by Paul Alper. The first essay, "Linda VA AG 2013 and Knitting Needles," provides examples of how a natural language does not necessarily work the way of logic. The second essay, "Words," discusses how the words of winners tend to become what we call the enduring historical record. The…

Modifying the mechanical properties of silk nanofiber scaffold by knitted orientation for regenerative medicine applications.

PubMed

Dodel, M; Hemmati Nejad, N; Bahrami, S H; Soleimani, M; Hanaee-Ahvaz, H

2016-08-31

Tissue reconstruction is among the increasing applications of polymer nanofibers. Fibrous scaffolds (mats) can be easily produced using the electrospinning method with structure and biomechanical properties similar to those of a cellular matrix. Electrospinning is widely used in the production of nanofibers and the GAP-method electrospinning is one of the means of producing fully aligned nanofibers. In this research, using the GAP-method, knitted fibrous scaffolds were made of silk fibroin, which is a biocompatible and biodegradable polymer. To extract fibroin from cocoons, the sodium chloride solution as well as dialysis and freeze-drying techniques were employed. The molecular weight of the extracted fibroin was measured with the SDS-Page electrophoresis technique. Moreover, the pure fibroin structure was examined using the ATR-FTIR method, and the viscosity of the solution used for electrospinning was measured with the Brookfield rotational viscometer. The scaffolds were prepared through electrospinning of the silk fibroin in pure formic acid solution. The following three structures were electrospun: 1) a random structure; 2) a knitted structure with an interstitial angle of 60 degrees; 3) a knitted structure with an interstitial angle of 90 degrees. Morphology of the resulting fibers was studied with a SEM (scanning electron microscope). Fibroin scaffolds are degradable in water. Therefore, they were fixated through immersion in methanol to be prepared for assays. The mechanical properties of the scaffolds were also studied using a tensile strength test device. The effect of methanol on the strength properties of the samples was also assessed. The hydrophilic potential of the samples was measured via a contact angle test. To increase the hydrophilicity of the scaffold surfaces, the cold oxygen plasma technique was employed. Finally, the biocompatibility and cell adhesion of the resulting scaffolds were examined through a HEK 293 cell culture, and the results

Drip bloodstain appearance on inclined apparel fabrics: Effect of prior-laundering, fibre content and fabric structure.

PubMed

de Castro, Therese C; Carr, Debra J; Taylor, Michael C; Kieser, Jules A; Duncan, Warwick

2016-09-01

The interaction of blood and fabrics is currently a 'hot topic', since the understanding and interpretation of these stains is still in its infancy. A recent simplified perpendicular impact experimental programme considering bloodstains generated on fabrics laid the foundations for understanding more complex scenarios. Blood rarely impacts apparel fabrics perpendicular; therefore a systematic study was conducted to characterise the appearance of drip stains on inclined fabrics. The final drip stain appearance for 45° and 15° impact angles on torso apparel fabrics (100% cotton plain woven, 100% polyester plain woven, a blend of polyester and cotton plain woven and 100% cotton single jersey knit) that had been laundered for six, 26 and 52 cycles prior to testing was investigated. The relationship between drop parameters (height and volume), angle and the stain characteristics (parent stain area, axis 1 and 2 and number of satellite stains) for each fabric was examined using analysis of variance. The appearance of the drip stains on these fabrics was distorted, in comparison to drip stains on hard-smooth surface. Examining the parent stain allowed for classification of stains occurring at an angle, however the same could not be said for the satellite stains produced. All of the dried stains visible on the surface of the fabric were larger than just after the impacting event, indicating within fabric spreading of blood due to capillary force (wicking). The cotton-containing fabrics spread the blood within the fabrics in all directions along the stain's circumference, while spreading within the polyester plain woven fabric occurred in only the weft (width of the fabric) and warp (length) directions. Laundering affected the formation of bloodstain on the blend plain woven fabric at both impact angles, although not all characteristics were significantly affected for the three impact conditions considered. The bloodstain characteristics varied due to the fibre content

Swine Model of Thrombotic Caval Occlusion Created by Autologous Thrombus Injection with Assistance of Intra-caval Net Knitting

PubMed Central

Shi, Wan-Yin; Wu, Shuang; Hu, Lan-Yue; Liu, Chang-Jian; Gu, Jian-Ping

2015-01-01

To evaluate the feasibility of a swine model of thrombotic inferior vena cava (IVC) occlusion (IVCO) created by autologous thrombus injection with assistance of intra-caval net knitting. Sixteen pigs were included and divided into two groups: Group A (n = 10), IVCO model created by knitting a caval net followed by autologous thrombus injection; Group B (n = 6), control model created by knitting a net and normal saline injection. Venography was performed to assess each model and the associated thrombotic occlusion. The vessels were examined histologically to analyse the pathological changes postoperatively. IVCO model was successfully created in 10 animals in Group A (100%). Immediate venography showed extensive clot burden in the IVC. Postoperative venography revealed partial caval occlusion at 7 days, and complete occlusion coupled with collateral vessels at 14 days. Histologically, Group A animals had significantly greater venous wall thickening, with CD163-positive and CD3-positive cell infiltration. Recanalization channels were observed at the margins of the thrombus. By contrast, no thrombotic occlusion of the IVC was observed in Group B. The thrombotic IVCO model can be reliably established in swine. The inflammatory reaction may contribute to the caval thrombus propagation following occlusion. PMID:26680253

Evaluation of High Temperature Knitted Spring Tubes for Structural Seal Applications

NASA Technical Reports Server (NTRS)

Taylor, Shawn C.; DeMange, Jeffrey J.; Dunlap, Patrick H., Jr.; Steinetz, Bruce M.

2004-01-01

Control surface seals are crucial to current and future space vehicles, as they are used to seal the gaps surrounding body flaps, elevons, and other actuated exterior surfaces. During reentry, leakage of high temperature gases through these gaps could damage underlying lower temperature structures such as rudder drive motors and mechanical actuators, resulting in impaired vehicle control. To be effective, control surface seals must shield lower temperature structures from heat transfer by maintaining sufficient resiliency to remain in contact with opposing sealing surfaces through multiple compression cycles. The current seal exhibits significant loss of resiliency after a few compression cycles at elevated temperatures (i.e., 1900 F) and therefore would be inadequate for advanced space vehicles. This seal utilizes a knitted Inconel X-750 spring tube as its primary resilient element. As part of a larger effort to enhance seal resiliency, researchers at the NASA Glenn Research Center performed high temperature compression testing (up to 2000 F) on candidate spring tube designs employing material substitutions and modified geometries. These tests demonstrated significant improvements in spring tube resiliency (5.5x better at 1750 F) through direct substitution of heat treated Rene 41 alloy in the baseline knit design. The impact of geometry modification was minor within the range of parameters tested, however trends did suggest that moderate resiliency improvements could be obtained by optimizing the current spring tube geometry.

29 CFR 530.1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... knitting process is performed; and the manufacture of bathing suits from any purchased fabric: Provided... other finishing of knitted shirts made in the same establishment as that where the knitting process is... embroidery, thread splitting, embroidery thread cutting, scallop cutting, lace cutting, lace making-up...

29 CFR 530.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... knitting process is performed; and the manufacture of bathing suits from any purchased fabric: Provided... other finishing of knitted shirts made in the same establishment as that where the knitting process is... embroidery, thread splitting, embroidery thread cutting, scallop cutting, lace cutting, lace making-up...

29 CFR 530.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... knitting process is performed; and the manufacture of bathing suits from any purchased fabric: Provided... other finishing of knitted shirts made in the same establishment as that where the knitting process is... embroidery, thread splitting, embroidery thread cutting, scallop cutting, lace cutting, lace making-up...

29 CFR 530.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... knitting process is performed; and the manufacture of bathing suits from any purchased fabric: Provided... other finishing of knitted shirts made in the same establishment as that where the knitting process is... embroidery, thread splitting, embroidery thread cutting, scallop cutting, lace cutting, lace making-up...

Innovative cellular distance structures from polymeric and metallic threads

NASA Astrophysics Data System (ADS)

Wieczorek, F.; Trümper, W.; Cherif, C.

2017-10-01

Knitting allows a high individual adaptability of the geometry and properties of flat-knitted spacer fabrics. This offers advantages for the specific adjustment of the mechanical properties of innovative composites based on highly viscous matrix systems such as bone cement, elastomer or foam and cellular reinforcing structures made from e. g. polymeric monofilaments or metallic wires. The prerequisite is the availability of binding solutions for highly productive production of functional, cellular, self-stabilized spacer flat knitted fabrics as supporting and functionalized structures.

Evaluation of textiles proposed for spacecraft crew apparel

NASA Technical Reports Server (NTRS)

Duncan, W. C.

1976-01-01

Textiles proposed for spacecraft wearing apparel were tested for possible primary irritancy and allergenicity using guinea pigs and human subjects. The materials submitted for testing were: (1) blue, loosely knit fabric of a copolymer of chlorotrifluoroethylene and ethylene (CTFE), (2) a white fabric, 100% cotton double knit, treated with fire retardant Tetrakis (hydroxymethyl) phosphonium hydroxide/ammonia, and (3) a gold colored polyimide fabric. There were no adverse reactions to any of the fabrics.

Light emitting fabric for photodynamic treatment of actinic keratosis

NASA Astrophysics Data System (ADS)

Thecua, E.; Vicentini, C.; Vignion, A.-S.; Lecomte, F.; Deleporte, P.; Mortier, L.; Szeimies, R.-M.; Mordon, S.

2017-02-01

The integration of optical fibers into flexible textile structures, by using knitting or weaving processes can allow the development of flexible light sources. The paper aims to present a new technology: Light Emitting Fabrics (LEF), which can be used for example for PDT of Actinic Keratosis in Dermatology. The predetermined macro-bending of optical fibers, led to a homogeneous side emission of light over the entire surface of the fabric. Tests showed that additional curvatures when applying the LEF on non-planar surfaces had no impact on light delivery and proved that LEF can adapt to the human morphology. The ability of the LEF, coupled with a 635nm LASER source, to deliver a homogeneous light to lesions is currently assessed in a clinical trial for the treatment of AK of the scalp by PDT. The low irradiance and progressive activation of the photosensitizer ensure a pain reduction, compared to discomfort levels experienced by patients during a conventional PDT session.

14 CFR 29.605 - Fabrication methods.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

14 CFR 29.605 - Fabrication methods.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

14 CFR 29.605 - Fabrication methods.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

14 CFR 29.605 - Fabrication methods.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

14 CFR 29.605 - Fabrication methods.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

14 CFR 27.605 - Fabrication methods.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 25.605 - Fabrication methods.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

14 CFR 27.605 - Fabrication methods.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 27.605 - Fabrication methods.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 25.605 - Fabrication methods.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

14 CFR 25.605 - Fabrication methods.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

14 CFR 27.605 - Fabrication methods.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 25.605 - Fabrication methods.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

14 CFR 27.605 - Fabrication methods.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 25.605 - Fabrication methods.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

Evaluation of materials proposed for use in space flight

NASA Technical Reports Server (NTRS)

Duncan, W. C.

1981-01-01

The primary irritancy and allergenicity of flame resistant treated cotton knit shirts proposed for use in space flight were evaluated. The knitted shirts were supplied by NASA as follows: knitted shirts with collars were made of two-ply mercerized single-knit cotton jersey. The fabric was treated with tetrakis (hydroxymethyl) phosphonium hydroxide and subsequently cured with gaseous ammonia (THPOH/NH3). The final treatment comprised adding on diammonium phosphate (DAP)/urea. The treated fabric was process scoured to remove extraneous materials, top softened and mechanically or chemically finished as required for specific needs. Diammonium phosphate is a more efficient flame inhabitant than the phosphonium; thus, the combination treatment served to impart higher resistance to ignition and sustained combustion as required by NASA test standard.

Thermoregulatory Responses to Intermittent Exercise Are Influenced by Knit Structure of Underwear

DTIC Science & Technology

1990-01-01

determined at 120 min, when Swo,(K3) and Swt(K4) were lower compared to both Sw,,(K2) and Swot (K5) 400 (Fig. 3). 300 Skin wettednessEE The knit...dew Pugh LGC (1966) Clothing insulation and accidential hypo- point temperature sensor. J Appl Physiol 52: 1658- 1660 thermia in youth. Nature 209: 1281...insulation. J Appl Physiol 8:539-545 cise and thermal stress. Physiol Rev 54:75-159 Hardy JI), )uBois EF (1938) Basal metabolism, radiation, Saltin B

19 CFR 10.607 - Goods eligible for tariff preference level claims.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., HTSUS, that are both cut (or knit-to-shape) and sewn or otherwise assembled in the territory of... wool fabric of subheading 5111.11.70, 5111.19.60, or 5111.90.90, HTSUS, the goods are both cut (or knit... U.S. Note 15(c), Subchapter XV, Chapter 99, HTSUS; (d) Apparel goods of Costa Rica, not knitted or...

16 CFR 1611.31 - Terms defined.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., which is woven, knitted, felted or otherwise produced from any natural or man-made fiber, or substitute... include those fabrics having fancy woven, knitted or flock printed surfaces. (h) The term raised surface...

Sensory interaction and descriptions of fabric hand.

PubMed

Burns, L D; Chandler, J; Brown, D M; Cameron, B; Dallas, M J

1995-08-01

82 subjects who viewed and felt fabrics (sensory interaction group) used different categories of terms to describe fabric hand than did 38 subjects who only felt the fabrics. Therefore, the methods used to measure fabric hand that isolate the senses may not accurately assess the way in which subjects describe fabric hand in nonlaboratory settings.

Knitted polylactide 96/4 L/D structures and scaffolds for tissue engineering: Shelf life, in vitro and in vivo studies

PubMed Central

Ellä, Ville; Annala, Tuija; Länsman, Satu; Nurminen, Manu; Kellomäki, Minna

2011-01-01

This study covers the whole production cycle, from biodegradable polymer processing to an in vivo tissue engineered construct. Six different biodegradable polylactide 96/4 L/D single jersey knits were manufactured using either four or eight multifilament fiber batches. The properties of those were studied in vitro for 42 weeks and in 0- to 3-year shelf life studies. Three types (Ø 12, 15 and 19 mm) of cylindrical scaffolds were manufactured from the knit, and the properties of those were studied in vitro for 48 weeks. For the Ø 15 mm scaffold type, mechanical properties were also studied in a one-year in vivo experiment. The scaffolds were implanted in the rat subcutis. All the scaffolds were g-irradiated prior to the studies. In vitro, all the knits lost 99% of their mechanical strength in 30 weeks. In the three-year follow up of shelf life properties, there was no decrease in the mechanical properties due to the storage time and only a 12% decrease in molecular weight. The in vitro and in vivo scaffolds lost their mechanical properties after 1 week. In the case of the in vivo samples, the mechanical properties were restored again, stepwise, by the presence of growing/maturing tissue between weeks 3 and 12. Faster degradation was observed with in vitro scaffolds compared to in vivo scaffolds during the one-year follow up. PMID:23507732

Effect of laundering on visible damage to apparel fabric caused by sharp force impact.

PubMed

Wells, S L; Laing, R M; Carr, D J; Niven, B E

2013-12-10

Sharp force violence is a common way of committing assault in numerous countries and regions around the world. When a stabbing occurs, the clothing worn by the victim may provide vital evidence: for example the weapon used to stab the victim may be identified from severance in the clothing. However, whether laundering the clothing after an attack affects the severance morphology of the fabric and fibres, and whether identification of the weapon is possible from the severance in the clothing after laundering is not known. This study focussed on the effect of laundering 100% cotton twill weave (drill) and single jersey (knit) fabrics. Specimens had been pre-treated and stabbed with either a kitchen knife or a Phillips screwdriver. These specimens were photographed and were again laundered for one wash cycle before being photographed again. Ten expert judges compared the photographs taken before and after laundering. A difference in the appearance of the fabrics before and after laundering was evident. The morphology of the fabric and fibres thus would be expected to differ after laundering the clothing, making identification of a weapon used to stab through clothing more difficult. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

A comparison of pure mode I and mixed mode I-III cracking of an adhesive containing an open knit cloth carrier

NASA Technical Reports Server (NTRS)

Ripling, E. J.; Crosley, P. B.; Johnson, W. S.

1988-01-01

Static and fatigue tests were carried out on two commercial modified epoxy film adhesives with a wide open knit polyester carrier in order to compare crack resistance in mode I and mixed mode I-III loading. The carrier cloth is found to have a significant influence on the cracking behavior of the adhesives. The open air net carrier used in this study separates from the adhesive in mode I cracking but shreds during mixed-mode crack extension. This decreases the opening mode toughness but increases the mixed-mode toughness as compared with results obtained earlier using a heavier knit carrier. The results suggest that the type of carrier may have a far larger influence on crack resistance than is generally recognized.

Design of a thermal waist-pad

NASA Astrophysics Data System (ADS)

Kursun Bahadir, S.; Sahin, U. K.; Acikgoz Tufan, H.

2017-10-01

The objective of the current study is designing a thermal waist-pad for people who have backaches with a sandwich-like multi-layered structure. Two model is developed; one is three-layered and second is five-layered with waterproof woven outer layer fabric, Thermolite® knitted fabric (for five-layered structures), wool knitted, polyester nonwoven fabric, polypropylene nonwoven fabric and viscose nonwoven fabric for mid-layer. 10 different structures are designed and produced. All samples are tested for thermal comfort properties of waist-pad. Multi-layer structures were tested, and according to their thermal performance and thermal comfort criteria, all results are evaluated for identifying the best product. These three factors are examined by analysis of thermal conductivity, thermal resistance, thermal absorptivity, relative water vapour/air permeability, water absorption. Highest thermal resistance test result, 150,42 mK/Wm2, is achieved in five-layered sandwich structure with waterproof fabric, Thermolite® fabric, wool based knitted fabric, Thermolite® fabric and waterproof fabric, respectively. Thermal conductivity result of this structure is 46,2 mW/mK, which is one of the lowest results among the alternative structures. Structures with Thermolite® fabric show higher thermal comfort when compared to others.

Conductive pathway on cotton fabric created using solution with silver organometallic compound

NASA Astrophysics Data System (ADS)

Campbell, Eric E.; He, Ruijian; Mayer, Michael

2017-10-01

A knitted cotton fabric is made conductive by thermal deposition of an organometallic silver compound (OSC). For the thermal process, the fabric was soaked with the OSC liquid and heated to 225 °C for 4 min. The cured state of the OSC is determined by the stabilization in the electrical resistance. The resulting silver metallization is shaped as nanoparticles and a continuous film. A typical resistance of a 10 cm  ×  1.5 cm metallized strip made with 1.9 ml OSC is 1.70 Ω. Various other resistance levels were achieved. A higher volume of OSC provided a lower electrical resistance for the metallized conductive path but increased its stiffness. Lower resistance was achieved by increasing the number of repeat coatings while keeping the OSC volume constant. The resistance decreased when the OSC coated fabric was elongated, an effect similar to negative piezoresistivity. A resistance of initially 0.34 Ω decreased to a minimum of 0.29 Ω at 10% elongation under repeated stretching and relaxation cycling. The metallization method reported here can be suitable for applications in the field know as technical textiles, electronic textiles (e-textiles), wearable electronics, functional garments, or smart fabrics.

Electromagnetic absorption behaviour of ferrite loaded three phase carbon fabric composites

NASA Astrophysics Data System (ADS)

Jagatheesan, Krishnasamy; Ramasamy, Alagirusamy; Das, Apurba; Basu, Ananjan

2018-02-01

This article investigates the electromagnetic absorption behaviours of carbon helical yarn fabric reinforced composites and manganese-zinc (Mn-Zn) ferrite particles loaded 3 phase fabric composites. A carbon helical yarn having stainless steel core was prepared and made into single jersey knitted fabric. The composite was prepared by sandwiching a fabric with polypropylene films and thermal pressed. The absorption values of helical yarn fabric composite was observed to be less in the C band region (4-8 GHz). For improving the absorption coefficients of composite, Mn-Zn ferrite particles were dispersed in the polypropylene (PP) composite. The ferrite loaded PP composites exhibited better permittivity and permeability values, hence the absorption loss of the composite was improved. The helical yarn fabric reinforced with Mn-Zn ferrite/PP composite showed larger absorption coefficients than virgin PP/fabric composite. The change in thermal stability and particle size distribution in the Mn-Zn ferrite/PP composite was also analyzed. At higher ferrite concentration, bimodal particle distribution was observed which increased the conductivity and shielding effectiveness (SE) of the composite. In addition, complex permittivity value was also increased for higher incident frequency (4-8 GHz). As the ferrite content increases, the dielectric loss and magnetic permeability of PP/ferrite increases due to increased magnetic loss. Hence, ferrite loaded PP composite showed the total SE of -14.2 dB with the absorption coefficients of 0.717. The S1C7 fabric composite having ferrite dispersion showed the better absorption loss and lower reflection coefficient of 14.2 dB and 0.345 respectively compared to virgin PP/helical yarn fabric composite. The increasing ferrite content (45 wt%) improved the absorption loss and total SE. Though, ferrite based fabric composite exhibits moderate absorptive shielding, it can be used as shielding panels in the electronic industries.

76 FR 78249 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

... Agreements (``CITA'') has determined that certain cotton/nylon/spandex raschel knit, open work crepe, piece... cotton/ nylon/spandex raschel knit, open crepe, piece dyed fabric, as specified below. On November 15... site for CAFTA-DR Commercial Availability proceedings. Specifications Certain Cotton/Nylon/Spandex...

"Close-knit" defines a healthy Native American Indian family.

PubMed

Martin, Donna; Yurkovich, Eleanor

2014-02-01

In the United States, the most significant health disparities occur among members of the American Indian and Alaskan Native populations. Because their health beliefs, values, and cultural practices are learned within a family system, this study used a focused ethnography to explore American Indians' perceptions of a healthy family. Seventeen interviews were performed with 21 adults residing on a reservation on the Northern Plains of the United States. Participant observation was conducted during 100 hr of fieldwork. All informants identified a healthy family as being "close-knit," indicating that the major defining feature of these families is the degree of connectedness among members, immediate and extended. In this paper, we present adult tribal members' descriptions of a healthy family. It is evident that culturally appropriate programs, which consider American Indians' values/beliefs and build on community assets, are urgently needed to reduce health disparities.

Electromechanical properties of polyamide/lycra fabric treated with PEDOT:PSS

NASA Astrophysics Data System (ADS)

Tadesse, M. G.; Mengistie, D. A.; Loghin, C.; Chen, Y.; Wang, L.; Catalin, D.; Müller, C.; Nierstrasz, V.

2017-10-01

One of the challenges in smart textiles is to develop suitable multifunctional materials that can address simultaneously several characteristics such as durability, stretchability, lightweight, and conductivity. Conductive polymers which showed success in different technological fields like polymer solar cells and light emitting diodes are promising in many smart textile applications. In this work, we treated a common polyamide/lycra knitted fabric with PEDOT:PSS for stretchable e-textiles. PEDOT:PSS, with DMSO as a conductivity enhancer and different ratios of water-based polyurethane dispersions as a binder, was applied to the fabric with simple immersion and coating applications. The effect of different application methods and binder ratio on the surface resistance of the fabric was monitored with four point probe electrical surface resistance measurement systems. Samples prepared by immersion technique are more uniform and have higher conductivity than those prepared by a coating technique. SEM images showed that PEDOT:PSS is incorporated into the structure in the immersion method while in the coating it is majorly present on the surface of the fabric. The tensile measurement showed that the acidic PEDOT:PSS and polyurethane dispersion coating has no adverse effect on the tensile strength of the fabric. The coated samples can be stretched up to 700% while still reasonably conductive. The resistance increases only by a small amount when samples were stretched cyclically by stretching 100%. Generally, samples prepared by the immersion method maintained better conductivity while stretching than those by a coating method. The washing fastness of the samples was also assessed.

Solution-Processed Metal Coating to Nonwoven Fabrics for Wearable Rechargeable Batteries.

PubMed

Lee, Kyulin; Choi, Jin Hyeok; Lee, Hye Moon; Kim, Ki Jae; Choi, Jang Wook

2017-12-27

Wearable rechargeable batteries require electrode platforms that can withstand various physical motions, such as bending, folding, and twisting. To this end, conductive textiles and paper have been highlighted, as their porous structures can accommodate the stress built during various physical motions. However, fabrics with plain weaves or knit structures have been mostly adopted without exploration of nonwoven counterparts. Also, the integration of conductive materials, such as carbon or metal nanomaterials, to achieve sufficient conductivity as current collectors is not well-aligned with large-scale processing in terms of cost and quality control. Here, the superiority of nonwoven fabrics is reported in electrochemical performance and bending capability compared to currently dominant woven counterparts, due to smooth morphology near the fiber intersections and the homogeneous distribution of fibers. Moreover, solution-processed electroless deposition of aluminum and nickel-copper composite is adopted for cathodes and anodes, respectively, demonstrating the large-scale feasibility of conductive nonwoven platforms for wearable rechargeable batteries. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Entropy Generation Analysis through Helical Coil Heat Exchanger in an Agitated Vessel

NASA Astrophysics Data System (ADS)

Ashok Reddy, K.

2018-03-01

Entropy Generation have been obtained while conducting the experiments for different sodium carboxymethyl cellulose concentrations 0.05%,0.1%,0.15% and 0.2% of Newtonian and non Newtonian fluids and the data made available by passing the test fluid at different flow rates through a helical coil in a mixing coil using paddle impeller. Heating of fluids depend on operational parameters, geometry of the mixing vessel and the type of impeller used. A new design of heating element was design and fabricated by providing kanthal wire inserted into a glove knitted with fiber glass yarn as glass fabric is flexible, heat resistant and can accommodate to adopt small difference in size of the vessel, perfectly. The knitted fabric is made to the shape of vessel used in the experiment and the heating elements are inserted so that it gets embedded and forms part of the glove knitted with yarn of fiber glass.

Some studies to prevent the production of some types of moire effects in fabrics

NASA Astrophysics Data System (ADS)

Serrano, Alfonso; Ponce, Rodrigo; Serroukh, Ibrahim

2004-09-01

The symmetry concerning the fabric pattern is not always suitable for the quality that we expected from fabric textile. The moire effects produced by a periodic structure may be caused by various and diverse factors as folds, lines, etc. The defect that we are concern is bright and dark fringes appearing in the Nylon Fabric are viewed with necked eye, from a particular angle using white light. To prevent these annoying effects, one should be focusing the research basically on geometrical fabric structure, physical, optical and dyeing. We start this work by an exhaustive study made to obtain enough information in order to identify and analyze the problem in order to identify, explain and prevent it appearance. To realize that we may define the factors that causes the phenomena. Concerning the experimental results, we begin with a conventional experiment called "Flat table examination" using Fluorescent white light bulb as types of illumination. We have used as well a microscope examination. It is useful to inspect the fiber and yarns which may have different characteristics of size and form. The light interaction with the fiber will produce especially kind of reflection and absorption. We finish the work by designing and developing an optical system able not only for detecting those kinds of fringes. As well to allow some defects inspection. We believe that some measurements are necessary during some process of fabrication (dyeing, spinning and knitting), at least to reduce this types of defects.

Protective constriction of coronary vein grafts with knitted nitinol

PubMed Central

Moodley, Loven; Franz, Thomas; Human, Paul; Wolf, Michael F.; Bezuidenhout, Deon; Scherman, Jacques; Zilla, Peter

2013-01-01

OBJECTIVES Different flow patterns and shear forces were shown to cause significantly more luminal narrowing and neointimal tissue proliferation in coronary than in infrainguinal vein grafts. As constrictive external mesh support of vein grafts led to the complete suppression of intimal hyperplasia (IH) in infrainguinal grafts, we investigated whether mesh constriction is equally effective in the coronary position. METHODS Eighteen senescent Chacma baboons (28.8 ± 3.6 kg) received aorto-coronary bypass grafts to the left anterior descending artery (LAD). Three groups of saphenous vein grafts were compared: untreated controls (CO); fibrin sealant-sprayed controls (CO + FS) and nitinol mesh-constricted grafts (ME + FS). Meshes consisted of pulse-compliant, knitted nitinol (eight needles; 50 μm wire thickness; 3.4 mm resting inner diameter, ID) spray attached to the vein grafts with FS. After 180 days of implantation, luminal dimensions and IH were analysed using post-explant angiography and macroscopic and histological image analysis. RESULTS At implantation, the calibre mismatch between control grafts and the LAD expressed as cross-sectional quotient (Qc) was pronounced [Qc = 0.21 ± 0.07 (CO) and 0.18 ± 0.05 (CO + FS)]. Mesh constriction resulted in a 29 ± 7% reduction of the outer diameter of the vein grafts from 5.23 ± 0.51 to 3.68 ± 0 mm, significantly reducing the calibre discrepancy to a Qc of 0.41 ± 0.17 (P < 0.02). After 6 months of implantation, explant angiography showed distinct luminal irregularities in control grafts (ID difference between widest and narrowest segment 74 ± 45%), while diameter variations were mild in mesh-constricted grafts. In all control grafts, thick neointimal tissue was present [600 ± 63 μm (CO); 627 ± 204 μm (CO + FS)] as opposed to thin, eccentric layers of 249 ± 83 μm in mesh-constricted grafts (ME + FS; P < 0.002). The total wall thickness had increased by 363 ± 39% (P < 0.00001) in CO and 312 ± 61% (P < 0

76 FR 66914 - Amendment of Limitation of Duty- and Quota-Free Imports of Apparel Articles Assembled in...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-28

... eligible fabrics, fabric components, or components knit-to-shape. Title VII of the Tax Relief and Health... Clothing (ATC), and the conversion factors for units of measure into square meter equivalents used by the...

Material and fabrication strategies for artificial muscles (Conference Presentation)

NASA Astrophysics Data System (ADS)

Spinks, Geoffrey M.

2017-04-01

Soft robotic and wearable robotic devices seek to exploit polymer based artificial muscles and sensor materials to generate biomimetic movements and forces. A challenge is to integrate the active materials into a complex, three-dimensional device with integrated electronics, power supplies and support structures. Both 3D printing and textiles technologies offer attractive fabrication strategies, but require suitable functional materials. 3D printing of actuating hydrogels has been developed to produce simple devices, such as a prototype valve. Tough hydrogels based on interpenetrating networks of ionicially crosslinked alginate and covalently crosslinked polyacrylamide and poly(N-isopropylacrylamide) have been developed in a form suitable for extrusion printing with UV curing. Combined with UV-curable and extrudable rigid acrylated urethanes, the tough hydrogels can be 3D printed into composite materials or complex shapes with multiple different materials. An actuating valve was printed that operated thermally to open or close the flow path using 6 parallel hydrogel actuators. Textile processing methods such as knitting and weaving can be used to generate assemblies of actuating fibres. Low cost and high performance coiled fibres made from oriented polymers have been used for developing actuating textiles. Similarly, braiding methods have been developed to fabricate new forms of McKibben muscles that operate without any external apparatus, such as pumps, compressors or piping.

Controlling adverse and beneficial effects of solar UV radiation by wearing suitable clothes - spectral transmission of different kinds of fabrics.

PubMed

Sobolewski, Piotr S; Krzyścin, Janusz W; Jarosławski, Janusz; Wink, Jakub; Lesiak, Aleksandra; Narbutt, Joanna

2014-11-01

Humans should avoid prolonged exposure to the Sun during the warm subperiod of the year with naturally high solar UV level. One of the known recommendations to avoid excessive UV radiation is wearing clothes with UV protection additives. However there is an important question: how do we get an adequate solar UV radiation, which maintains a healthy status of vitamin D, without facing overexposure risks? It is found that some kind of 100% cotton knitted fabric, used in the production of normal daily clothing, has ∼15% transmittance of solar UV. Model studies show that a garment made of this fabric allows larger synthesis of vitamin D3 in human body without the erythema risks (skin redness). Thus the adequate level of vitamin D could be attained safely by a person exposing only small part of the body (face, palms) during the period (May-August) of the year. Copyright © 2014 Elsevier B.V. All rights reserved.

[Compression treatment for burned skin].

PubMed

Jaafar, Fadhel; Lassoued, Mohamed A; Sahnoun, Mahdi; Sfar, Souad; Cheikhrouhou, Morched

2012-02-01

The regularity of a compressive knit is defined as its ability to perform its function in a burnt skin. This property is essential to avoid the phenomenon of rejection of the material or toxicity problems But: Make knits biocompatible with high burnet of human skin. We fabric knits of elastic material. To ensure good adhesion to the skin, we made elastic material, typically a tight loop knitted. The Length of yarn absorbed by stitch and the raw matter are changed with each sample. The physical properties of each sample are measured and compared. Surface modifications are made to these samples by impregnation of microcapsules based on jojoba oil. Knits are compressif, elastic in all directions, light, thin, comfortable, and washable for hygiene issues. In addition, the washing can find their compressive properties. The Jojoba Oil microcapsules hydrated the human burnet skin. This moisturizer is used to the firmness of the wound and it gives flexibility to the skin. Compressive Knits are biocompatible with burnet skin. The mixture of natural and synthetic fibers is irreplaceable in terms comfort and regularity.

Evaluation of microplastic release caused by textile washing processes of synthetic fabrics.

PubMed

De Falco, Francesca; Gullo, Maria Pia; Gentile, Gennaro; Di Pace, Emilia; Cocca, Mariacristina; Gelabert, Laura; Brouta-Agnésa, Marolda; Rovira, Angels; Escudero, Rosa; Villalba, Raquel; Mossotti, Raffaella; Montarsolo, Alessio; Gavignano, Sara; Tonin, Claudio; Avella, Maurizio

2018-05-01

A new and more alarming source of marine contamination has been recently identified in micro and nanosized plastic fragments. Microplastics are difficult to see with the naked eye and to biodegrade in marine environment, representing a problem since they can be ingested by plankton or other marine organisms, potentially entering the food web. An important source of microplastics appears to be through sewage contaminated by synthetic fibres from washing clothes. Since this phenomenon still lacks of a comprehensive analysis, the objective of this contribution was to investigate the role of washing processes of synthetic textiles on microplastic release. In particular, an analytical protocol was set up, based on the filtration of the washing water of synthetic fabrics and on the analysis of the filters by scanning electron microscopy. The quantification of the microfibre shedding from three different synthetic fabric types, woven polyester, knitted polyester, and woven polypropylene, during washing trials simulating domestic conditions, was achieved and statistically analysed. The highest release of microplastics was recorded for the wash of woven polyester and this phenomenon was correlated to the fabric characteristics. Moreover, the extent of microfibre release from woven polyester fabrics due to different detergents, washing parameters and industrial washes was evaluated. The number of microfibres released from a typical 5 kg wash load of polyester fabrics was estimated to be over 6,000,000 depending on the type of detergent used. The usage of a softener during washes reduces the number of microfibres released of more than 35%. The amount and size of the released microfibres confirm that they could not be totally retained by wastewater treatments plants, and potentially affect the aquatic environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

75 FR 6169 - Request for Public Comment on a Commercial Availability Request Under the U.S.-Singapore Free...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-08

... centimeters (52 inches). Finish: (Piece) dyed. Fabric 2 HTS Subheading: 6004.10.00. Fiber Content: 35% rayon...). Finish: (Piece) dyed. Fabric 3 HTS Subheading: 6001.22.00. Fiber Content: 79% rayon made from bamboo/15...: (Piece) dyed. (2) Certain knit fabrics of polyester fiber, of the specifications detailed below...

19 CFR 10.242 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... knitting machine. Several components with finished edges may be linked by yarn or thread as they are... reference to fabric components, means that all of the production processes, starting with the production of... fabric(s), means that all of the production processes, starting with polymers, fibers, filaments, textile...

19 CFR 10.242 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... knitting machine. Several components with finished edges may be linked by yarn or thread as they are... reference to fabric components, means that all of the production processes, starting with the production of... fabric(s), means that all of the production processes, starting with polymers, fibers, filaments, textile...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.242 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... knitting machine. Several components with finished edges may be linked by yarn or thread as they are... reference to fabric components, means that all of the production processes, starting with the production of... fabric(s), means that all of the production processes, starting with polymers, fibers, filaments, textile...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.242 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... knitting machine. Several components with finished edges may be linked by yarn or thread as they are... reference to fabric components, means that all of the production processes, starting with the production of... fabric(s), means that all of the production processes, starting with polymers, fibers, filaments, textile...

19 CFR 10.242 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... knitting machine. Several components with finished edges may be linked by yarn or thread as they are... reference to fabric components, means that all of the production processes, starting with the production of... fabric(s), means that all of the production processes, starting with polymers, fibers, filaments, textile...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

Feminist Framework Plus: Knitting Feminist Theories of Rape Etiology Into a Comprehensive Model.

PubMed

McPhail, Beverly A

2016-07-01

The radical-liberal feminist perspective on rape posits that the assault is motivated by power and control rather than sexual gratification and is a violent rather than a sexual act. However, rape is a complex act. Relying on only one early strand of feminist thought to explain the etiology of rape limits feminists' understanding of rape and the practice based upon the theory. The history of the adoption of the "power, not sex" theory is presented and the model critiqued. A more integrated model is developed and presented, the Feminist Framework Plus, which knits together five feminist theories into a comprehensive model that better explains the depth and breadth of the etiology of rape. Empirical evidence that supports each theory is detailed as well as the implications of the model on service provision, education, and advocacy. © The Author(s) 2015.

16 CFR 303.33 - Country where textile fiber products are processed or manufactured.

Code of Federal Regulations, 2011 CFR

2011-01-01

... “Scarf made in USA of fabric made in China” or “Comforter Filled, Sewn and Finished in the U.S. With Shell Made in China” or “Made in [Foreign Country]/fabric made in USA” or “Knit in USA, assembled in...

16 CFR 303.33 - Country where textile fiber products are processed or manufactured.

Code of Federal Regulations, 2010 CFR

2010-01-01

... “Scarf made in USA of fabric made in China” or “Comforter Filled, Sewn and Finished in the U.S. With Shell Made in China” or “Made in [Foreign Country]/fabric made in USA” or “Knit in USA, assembled in...

Proceedings of the twelfth target fabrication specialists` meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1999-04-01

Research in fabrication for inertial confinement fusion (ICF) comprises at least three broad categories: targets for high energy density physics on existing drivers, ignition capsule fabrication, and cryogenic fuel layer formation. The latter two are being pursued primarily for the National Ignition Facility (NIF). Scientists from over 14 laboratories, universities, and businesses contributed over 100 papers on all aspects of ICF target fabrication. The NIF is well along in construction and photos of poured concrete and exposed steel added to the technical excitement. It was clear from the meeting that there has been significant progress toward the fabrication of anmore » ignition target for NIF and that new techniques are resulting in higher quality targets for high energy density research.« less

Preparation of Biocomposite Microfibers Ready for Processing into Biologically Active Textile Fabrics for Bioremediation.

PubMed

Kaiser, Patrick; Reich, Steffen; Greiner, Andreas; Freitag, Ruth

2018-06-12

Biocomposites, i.e., materials consisting of metabolically active microorganisms embedded in a synthetic extracellular matrix, may find applications as highly specific catalysts in bioproduction and bioremediation. 3D constructs based on fibrous biocomposites, so-called "artificial biofilms," are of particular interest in this context. The inability to produce biocomposite fibers of sufficient mechanical strength for processing into bioactive fabrics has so far hindered progress in the area. Herein a method is proposed for the direct wet spinning of microfibers suitable for weaving and knitting. Metabolically active bacteria (either Shewanella oneidensis or Nitrobacter winogradskyi (N. winogradskyi)) are embedded in these fibers, using poly(vinyl alcohol) as matrix. The produced microfibers have a partially crystalline structure and are stable in water without further treatment, such as coating. In a first application, their potential for nitrite removal (N. winogradskyi) is demonstrated, a typical challenge in potable water treatment. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Category Coherence and Category-Based Property Induction

ERIC Educational Resources Information Center

Rehder, Bob; Hastie, Reid

2004-01-01

One important property of human object categories is that they define the sets of exemplars to which newly observed properties are generalized. We manipulated the causal knowledge associated with novel categories and assessed the resulting strength of property inductions. We found that the theoretical coherence afforded to a category by…

Feature-based versus category-based induction with uncertain categories.

PubMed

Griffiths, Oren; Hayes, Brett K; Newell, Ben R

2012-05-01

Previous research has suggested that when feature inferences have to be made about an instance whose category membership is uncertain, feature-based inductive reasoning is used to the exclusion of category-based induction. These results contrast with the observation that people can and do use category-based induction when category membership is known. The present experiments examined the conditions that drive feature-based and category-based strategies in induction under category uncertainty. Specifically, 2 experiments investigated whether reliance on feature-based inductive strategies is a product of the lack of coherence in the categories used in previous research or is due to the use of a decision-only induction procedure. Experiment 1 found that feature-based reasoning remained the preferred strategy even when categories with relatively high internal coherence were used. Experiment 2 found a shift toward category-based reasoning when participants were trained to classify category members prior to feature induction. Together, these results suggest that an appropriate conceptual representation must be formed through experience with a category before it is likely to be used as a basis for feature induction. (c) 2012 APA, all rights reserved.

Perceptual effects of linguistic category priming: the Stapel and Semin (2007) paradigm revisited in twelve experiments.

PubMed

IJzerman, Hans; Regenberg, Nina F E; Saddlemyer, Justin; Koole, Sander L

2015-05-01

Linguistic category priming is a novel paradigm to examine automatic influences of language on cognition (Semin, 2008). An initial article reported that priming abstract linguistic categories (adjectives) led to more global perceptual processing, whereas priming concrete linguistic categories (verbs) led to more local perceptual processing (Stapel & Semin, 2007). However, this report was compromised by data fabrication by the first author, so that it remains unclear whether or not linguistic category priming influences perceptual processing. To fill this gap in the literature, the present article reports 12 studies among Dutch and US samples examining the perceptual effects of linguistic category priming. The results yielded no evidence of linguistic category priming effects. These findings are discussed in relation to other research showing cultural variations in linguistic category priming effects (IJzerman, Saddlemyer, & Koole, 2014). The authors conclude by highlighting the importance of conducting and publishing replication research for achieving scientific progress. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

19 CFR 10.248 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to an...

19 CFR 10.228 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to a...

19 CFR 10.228 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to a...

19 CFR 10.248 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to an...

19 CFR 10.843 - Articles eligible for duty-free treatment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... paragraphs (a) through (j) of this section that are imported directly from Haiti or the Dominican Republic...-shape, and yarns, subject to the applicable quantitative limits set forth in U.S. Note 6(g), Subchapter...-shape, and yarns, without regard to the source of the fabric, fabric components, components knit-to...

19 CFR 10.843 - Articles eligible for duty-free treatment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... paragraphs (a) through (j) of this section that are imported directly from Haiti or the Dominican Republic...-shape, and yarns, subject to the applicable quantitative limits set forth in U.S. Note 6(g), Subchapter...-shape, and yarns, without regard to the source of the fabric, fabric components, components knit-to...

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

NASA Technical Reports Server (NTRS)

Suarez, J.; Dastin, S.

1992-01-01

Innovative design concepts and cost effective fabrication processes were developed for damage tolerant primary structures that can perform at a design ultimate strain level of 6000 micro inch/inch. Attention focused on the use of textile high performance fiber reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials and/or processes methods is described: fabricated using IM7 angle interlock 0 to 90 deg woven preforms with + or - 45 deg plies stitched with Toray high strength graphite thread and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms using RTM and Tactix 123/H41 epoxy; and fabricated preforms using AS4(6K)/PEEK 150 g commingled angle interlock 0 to 90 deg woven preforms with + or - 45 deg commingled plies stitched using high strength graphite thread and processed by consolidation. Structural efficiency, processability, and acquisition cost are compared.

Feature-Based versus Category-Based Induction with Uncertain Categories

ERIC Educational Resources Information Center

Griffiths, Oren; Hayes, Brett K.; Newell, Ben R.

2012-01-01

Previous research has suggested that when feature inferences have to be made about an instance whose category membership is uncertain, feature-based inductive reasoning is used to the exclusion of category-based induction. These results contrast with the observation that people can and do use category-based induction when category membership is…

[Total cavopulmonary connection using a knitted dacron prosthesis impregnated with gelatin (GELSEAL) as an intracardiac conduit].

PubMed

Iwaya, F; Tanji, M; Ono, T; Tsuda, A; Hoshino, S

1996-05-01

It is important to find a suitable vascular prosthesis as an intracardiac conduit for a total cavopulmonary connection because of the need for long-term patency. A 7-year-old girl with a double outlet of right ventricle, hypoplastic left ventricle, pulmonary atresia and single atrium with azygos connection underwent a total cavopulmonary connection using a knitted dacron prosthesis impregnated with gelatin (GELSEAL) as an intracardiac conduit. Her postoperative course was uneventful. GELSEAL is soft, easy to hand and effective at preventing blood loss. The conduit is also expected to have long-term patency because of good healing with thin and uniform pseudointimal formation. However, long-term patency especially in the right side of the heart is still unknown. She should be followed with close anticoagulant therapy and careful observation.

Textile Supercapacitors

NASA Astrophysics Data System (ADS)

Jost, Kristy Alana

Innovative and interdisciplinary solutions to wearable textile energy storage are explored as power sources for wearable electronics and smart textiles. Due to their long cycle life, non-toxic and inexpensive materials, supercapacitors were converted into textiles. Textile supercapacitors were developed using scalable fabrication methods including screen-printing, yarn making, and 3D computerized knitting. The electrode materials reported in this thesis undergo thorough electrochemical analysis, and are capable of storing up to 0.5 F/cm2 which is on par with conventionally solid supercapacitors (0.6 F/cm2). Capacitive yarns are capable of storing up to 37 mF/cm and are shown to be knittable on industrial knitting equipment. Both are some of the highest reported capacitance for all-carbon systems in the field. Yet both are the only systems composed of inexpensive and non-toxic activated carbon, the most commonly used electrode material used in supercapacitors, opposed to carbon nanotubes or graphene, which are typically more 10-100 times more expensive. However, all of the fabrication techniques reported here are also capable of incorporating a wide variety of materials, ultimately broadening the applications of textile energy storage as a whole. Fully machine knitted supercapacitors are also explored and electrochemically characterized in order to determine how the textile structure affects the capacitance. In conclusion, a wide variety of fabrication techniques for making textile supercapacitors were successfully explored.

Kid's Play.

ERIC Educational Resources Information Center

Whalen, Susan L.

1998-01-01

Examines the use of fabric mesh knitting as canopies for children's playgrounds. Its benefits and drawbacks are addressed as are how innovative design and choice of materials can help eliminate function difficulties. (GR)

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded, extruded, and...

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2014 CFR

2014-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... (CONTINUED) RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded...

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2013 CFR

2013-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... (CONTINUED) RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded...

Self-expandable macroporous nitinol stents for transfemoral exclusion of aortic aneurysms in dogs: preliminary results.

PubMed

Hagen, B; Harnoss, B M; Trabhardt, S; Ladeburg, M; Fuhrmann, H; Franck, C

1993-01-01

This experimental study evaluated the feasibility of excluding artificially created aortic aneurysms in dogs with transfemorally inserted nitinol stents, serving as intraluminal bypass. Infrarenal aortic aneurysms were created in eleven dogs (28-35 kg) by end-to-end anastomosis of sacciform conduits. Single and double wire-knitted, macroporous, superelastic, self-expanding nitinol stents without any additional wrapping or in-between fabrics served as endovascular grafts. The pore size of the double-knitted stents was less than 0.7 mm2. Angiography following stent placement showed immediate exclusion of the aneurysms for the double-knitted stents. For the single-knitted stents (2 cases), partial exclusion was achieved only after considerable delay. CT studies in the dogs with the double-knitted stents revealed patency of the grafts after 3 to 5 weeks with the aneurysms totally thrombosed. So far gross pathology of 1 dog at 24 h and 1 at 12 months revealed patency of the stents. At 12 months histopathology showed a neointima covering the inner stent surface with the aneurysm filled by an organized thrombus. It is concluded, that an "open" stent with a tight meshwork appears to be a suitable device to instantly exclude artificial aneurysms of the canine aorta.

Knitting aromatic polymers for efficient solid-phase microextraction of trace organic pollutants.

PubMed

Liu, Shuqin; Hu, Qingkun; Zheng, Juan; Xie, Lijun; Wei, Songbo; Jiang, Ruifen; Zhu, Fang; Liu, Yuan; Ouyang, Gangfeng

2016-06-10

A series of knitting aromatic polymers (KAPs) were successfully synthesized using a simple one-step Friedel-Crafts alkylation of aromatic monomers and were characterized by transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). Then, as-synthesized KAPs with large surface areas, unique pore structures and high thermal stability were prepared as solid-phase microextraction (SPME) coatings that exhibited good extraction abilities for a series of benzene compounds (i.e., benzene, toluene, ethylbenzene and m-xylene, which are referred to as BTEX) and polycyclic aromatic hydrocarbons (PAHs). Under the optimized conditions, the methodologies established for the determination of BTEX and PAHs using the KAPs-triPB and KAPs-B coatings, respectively, possessed wide linear ranges, low limits of detection (LODs, 0.10-1.13ngL(-1) for BTEX and 0.05-0.49ngL(-1) for PAHs) and good reproducibility. Finally, the proposed methods were successfully applied to the determination of BTEX and PAHs in environmental water samples, and satisfactory recoveries (93.6-124.2% for BTEX and 77.2-113.3% for PAHs) were achieved. This study provides a benchmark for exploiting novel microporous organic polymers (MOPs) for SPME applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Further Investigations of High Temperature Knitted Spring Tubes for Advanced Control Surface Seal Applications

NASA Technical Reports Server (NTRS)

Taylor, Shawn C.; DeMange, Jeffrey J.; Dunlap, Patrick H., Jr.; Steinetz, Bruce M.

2006-01-01

Knitted metallic spring tubes are the structural backbones that provide resiliency in control surface seals for use on current and future reusable space launch vehicles. Control surface seals fill the space between movable control surfaces such as body flaps, rudders and elevons, and the static body structures to which they are attached. These seals must remain in continuous contact with opposing surfaces to prevent the ingestion of damaging hot gases encountered during atmospheric re-entry. The Inconel X-750 (Special Metals Corporation) spring tube utilized in the baseline control surface seal shows significant resiliency loss when compressed at temperatures as low as 1200 F. High temperature compression testing and microstructural analysis show that creep is the dominant deformation mechanism leading to permanent set and resiliency loss in tested spring tube samples. Additional evaluation using a structured design of experiments approach shows that spring tube performance, primarily high temperature resiliency, can be enhanced through material substitution of Rene 41 (Allvac) alloy (for the baseline Inconel X-750 material) when coupled with specialized thermal processing.

New single-layer compression bandage system for chronic venous leg ulcers.

PubMed

Lee, Gillian; Rajendran, Subbiyan; Anand, Subhash

A new single-layer bandage system for the treatment of venous leg ulcers has been designed and developed at the University of Bolton. This three-dimensional (3D) knitted spacer fabric structure has been designed by making use of mathematical modelling and Laplace's law. The sustained graduated compression of the developed 3D knitted spacer bandages were tested and characterized, and compared with that of commercially available compression bandages. It was observed that the developed 3D single-layer bandage meets the ideal criteria stipulated for compression therapy. The laboratory results were verified by carrying out a pilot user study incorporating volunteers from different age groups. This article examines the insight into the design and development of the new 3D knitted spacer bandage, along with briefly discussing the issues of compression therapy systems intended for the treatment of venous leg ulcers.

Category labels versus feature labels: category labels polarize inferential predictions.

PubMed

Yamauchi, Takashi; Yu, Na-Yung

2008-04-01

What makes category labels different from feature labels in predictive inference? This study suggests that category labels tend to make inductive reasoning polarized and homogeneous. In two experiments, participants were shown two schematic pictures of insects side by side and predicted the value of a hidden feature of one insect on the basis of the other insect. Arbitrary verbal labels were shown above the two pictures, and the meanings of the labels were manipulated in the instructions. In one condition, the labels represented the category membership of the insects, and in the other conditions, the same labels represented attributes of the insects. When the labels represented category membership, participants' responses became substantially polarized and homogeneous, indicating that the mere reference to category membership can modify reasoning processes.

Finger materials for air cushion vehicles. Volume 1: Flexible coatings for finger materials

NASA Astrophysics Data System (ADS)

Conn, P. K.; Snell, I. C.; Klemens, W.

1984-12-01

Twenty polymer formulations from ten selected gum rubber polymers or polymer blends and fourteen formulations of castable liquid polyurethane polymers were characterized as coatings for the coated fabric that is the type material used to make flexible fingers for air cushion vehicles. The formulations were screened for crack growth and flexural fatigue resistance; the results were compared to results from a natural rubber/cisabutadiene blend control coating. In addition, selected polymers were evaluated with primary and secondary characterization tests and the results compared to results from the control formulation. One polymer also was used to evaluate the use of a reticulated carbon black to improve thermal conductivity. Several polymers had better crack growth resistance and a number had better flexural fatique resistance than the control polymer. A clorinated polyethylene polymer coated on nylon fabric had properties equivalent to the control polymer coated on nylon fabric. Hysteresis tests at different rates of deformation yielded results which suggested that the standard tests may not identify polymers with improved performance on air cushion vehicles. Woven fabric, knit, and mat structures were evaluated as reinforcements for polymer coatings; the knit and mat structures were not as efficient on a strength-to-weight basis as woven fabrics.

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

NASA Technical Reports Server (NTRS)

Suarez, J.; Dastin, S.

1992-01-01

Under NASA's Novel Composites for Wing and Fuselage Applications (NCWFA) Program, Grumman is developing innovative design concepts and cost-effective fabrication processes for damage-tolerant primary structures that can perform at a design ultimate strain level of 6000 micro-inch/inch. Attention has focused on the use of textile high-performance fiber-reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low-cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials/processes methods is described: 'Y' spars fabricated using IM7 angle interlock 0/90 deg woven preforms with +/- 45 deg plies stitched with Toray high-strength graphite thread and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RTM and Tactix 123/H41 epoxy; and 'Y' spars fabricated using AS4(6k)/PEEK 150-g commingled angle interlock 0/90 deg woven preforms with +/- 45 deg commingled plies stitched using high-strength graphite thread and processed by consolidation. A comparison of the structural efficiency, processability, and projected acquisition cost of these representative spars is presented.

46 CFR 164.009-3 - Noncombustible materials not requiring specific approval.

Code of Federal Regulations, 2010 CFR

2010-10-01

... subpart: (a) Sheet glass, block glass, clay, ceramics, and uncoated fibers. (b) All metals, except... only sand, gravel, expanded vermiculite, expanded or vesicular slags, diatomaceous silica, perlite, or pumice. (d) Woven, knitted or needle punched glass fabric containing no additives other than lubricants...

76 FR 79166 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-21

... (``CITA'') has determined that certain cotton/nylon/spandex raschel knit open work crepe printed fabric... determination (``Request'') from Sorini Samet & Associates on behalf of Hansoll Textile Ltd. for certain cotton... site for CAFTA-DR Commercial Availability proceedings. SPECIFICATIONS: Certain Cotton/Nylon/Spandex...

Category vs. Object Knowledge in Category-Based Induction

ERIC Educational Resources Information Center

Murphy, Gregory L.; Ross, Brian H.

2010-01-01

In one form of category-based induction, people make predictions about unknown properties of objects. There is a tension between predictions made based on the object's specific features (e.g., objects above a certain size tend not to fly) and those made by reference to category-level knowledge (e.g., birds fly). Seven experiments with artificial…

Accuracy evaluation of metal copings fabricated by computer-aided milling and direct metal laser sintering systems

PubMed Central

Lee, Wan-Sun; Kim, Woong-Chul

2015-01-01

PURPOSE To assess the marginal and internal gaps of the copings fabricated by computer-aided milling and direct metal laser sintering (DMLS) systems in comparison to casting method. MATERIALS AND METHODS Ten metal copings were fabricated by casting, computer-aided milling, and DMLS. Seven mesiodistal and labiolingual positions were then measured, and each of these were divided into the categories; marginal gap (MG), cervical gap (CG), axial wall at internal gap (AG), and incisal edge at internal gap (IG). Evaluation was performed by a silicone replica technique. A digital microscope was used for measurement of silicone layer. Statistical analyses included one-way and repeated measure ANOVA to test the difference between the fabrication methods and categories of measured points (α=.05), respectively. RESULTS The mean gap differed significantly with fabrication methods (P<.001). Casting produced the narrowest gap in each of the four measured positions, whereas CG, AG, and IG proved narrower in computer-aided milling than in DMLS. Thus, with the exception of MG, all positions exhibited a significant difference between computer-aided milling and DMLS (P<.05). CONCLUSION Although the gap was found to vary with fabrication methods, the marginal and internal gaps of the copings fabricated by computer-aided milling and DMLS fell within the range of clinical acceptance (<120 µm). However, the statistically significant difference to conventional casting indicates that the gaps in computer-aided milling and DMLS fabricated restorations still need to be further reduced. PMID:25932310

Accuracy evaluation of metal copings fabricated by computer-aided milling and direct metal laser sintering systems.

PubMed

Park, Jong-Kyoung; Lee, Wan-Sun; Kim, Hae-Young; Kim, Woong-Chul; Kim, Ji-Hwan

2015-04-01

To assess the marginal and internal gaps of the copings fabricated by computer-aided milling and direct metal laser sintering (DMLS) systems in comparison to casting method. Ten metal copings were fabricated by casting, computer-aided milling, and DMLS. Seven mesiodistal and labiolingual positions were then measured, and each of these were divided into the categories; marginal gap (MG), cervical gap (CG), axial wall at internal gap (AG), and incisal edge at internal gap (IG). Evaluation was performed by a silicone replica technique. A digital microscope was used for measurement of silicone layer. Statistical analyses included one-way and repeated measure ANOVA to test the difference between the fabrication methods and categories of measured points (α=.05), respectively. The mean gap differed significantly with fabrication methods (P<.001). Casting produced the narrowest gap in each of the four measured positions, whereas CG, AG, and IG proved narrower in computer-aided milling than in DMLS. Thus, with the exception of MG, all positions exhibited a significant difference between computer-aided milling and DMLS (P<.05). Although the gap was found to vary with fabrication methods, the marginal and internal gaps of the copings fabricated by computer-aided milling and DMLS fell within the range of clinical acceptance (<120 µm). However, the statistically significant difference to conventional casting indicates that the gaps in computer-aided milling and DMLS fabricated restorations still need to be further reduced.

Discontinuous categories affect information-integration but not rule-based category learning.

PubMed

Maddox, W Todd; Filoteo, J Vincent; Lauritzen, J Scott; Connally, Emily; Hejl, Kelli D

2005-07-01

Three experiments were conducted that provide a direct examination of within-category discontinuity manipulations on the implicit, procedural-based learning and the explicit, hypothesis-testing systems proposed in F. G. Ashby, L. A. Alfonso-Reese, A. U. Turken, and E. M. Waldron's (1998) competition between verbal and implicit systems model. Discontinuous categories adversely affected information-integration but not rule-based category learning. Increasing the magnitude of the discontinuity did not lead to a significant decline in performance. The distance to the bound provides a reasonable description of the generalization profile associated with the hypothesis-testing system, whereas the distance to the bound plus the distance to the trained response region provides a reasonable description of the generalization profile associated with the procedural-based learning system. These results suggest that within-category discontinuity differentially impacts information-integration but not rule-based category learning and provides information regarding the detailed processing characteristics of each category learning system. ((c) 2005 APA, all rights reserved).

Incidental Auditory Category Learning

PubMed Central

Gabay, Yafit; Dick, Frederic K.; Zevin, Jason D.; Holt, Lori L.

2015-01-01

Very little is known about how auditory categories are learned incidentally, without instructions to search for category-diagnostic dimensions, overt category decisions, or experimenter-provided feedback. This is an important gap because learning in the natural environment does not arise from explicit feedback and there is evidence that the learning systems engaged by traditional tasks are distinct from those recruited by incidental category learning. We examined incidental auditory category learning with a novel paradigm, the Systematic Multimodal Associations Reaction Time (SMART) task, in which participants rapidly detect and report the appearance of a visual target in one of four possible screen locations. Although the overt task is rapid visual detection, a brief sequence of sounds precedes each visual target. These sounds are drawn from one of four distinct sound categories that predict the location of the upcoming visual target. These many-to-one auditory-to-visuomotor correspondences support incidental auditory category learning. Participants incidentally learn categories of complex acoustic exemplars and generalize this learning to novel exemplars and tasks. Further, learning is facilitated when category exemplar variability is more tightly coupled to the visuomotor associations than when the same stimulus variability is experienced across trials. We relate these findings to phonetic category learning. PMID:26010588

Category-length and category-strength effects using images of scenes.

PubMed

Baumann, Oliver; Vromen, Joyce M G; Boddy, Adam C; Crawshaw, Eloise; Humphreys, Michael S

2018-06-21

Global matching models have provided an important theoretical framework for recognition memory. Key predictions of this class of models are that (1) increasing the number of occurrences in a study list of some items affects the performance on other items (list-strength effect) and that (2) adding new items results in a deterioration of performance on the other items (list-length effect). Experimental confirmation of these predictions has been difficult, and the results have been inconsistent. A review of the existing literature, however, suggests that robust length and strength effects do occur when sufficiently similar hard-to-label items are used. In an effort to investigate this further, we had participants study lists containing one or more members of visual scene categories (bathrooms, beaches, etc.). Experiments 1 and 2 replicated and extended previous findings showing that the study of additional category members decreased accuracy, providing confirmation of the category-length effect. Experiment 3 showed that repeating some category members decreased the accuracy of nonrepeated members, providing evidence for a category-strength effect. Experiment 4 eliminated a potential challenge to these results. Taken together, these findings provide robust support for global matching models of recognition memory. The overall list lengths, the category sizes, and the number of repetitions used demonstrated that scene categories are well-suited to testing the fundamental assumptions of global matching models. These include (A) interference from memories for similar items and contexts, (B) nondestructive interference, and (C) that conjunctive information is made available through a matching operation.

40 CFR 428.50 - Applicability; description of the small-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... RUBBER MANUFACTURING POINT SOURCE CATEGORY Small-Sized General Molded, Extruded, and Fabricated Rubber..., foam rubber backing, rubber cement-dipped goods, and retreaded tires by small-sized plants...

40 CFR 428.70 - Applicability; description of the large-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... RUBBER MANUFACTURING POINT SOURCE CATEGORY Large-Sized General Molded, Extruded, and Fabricated Rubber..., foam rubber backing, rubber cement-dipped goods, and retreaded tires by large-sized plants...

Rank 4 Premodular Categories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruillard, Paul J.; Galindo, Cesar; Ng, Siu Hung

2016-09-01

We consider the classification problem for rank 4 premodular categories. We uncover a formula for the 2nd Frobenius-Schur indicator of a premodular category is determined and the classification of rank 4 premodular categories (up to Grothendieck equivalence) is completed. In the appendix we show rank finiteness for premodular categories.

Ideals and Category Typicality

ERIC Educational Resources Information Center

Kim, ShinWoo; Murphy, Gregory L.

2011-01-01

Barsalou (1985) argued that exemplars that serve category goals become more typical category members. Although this claim has received support, we investigated (a) whether categories have a single ideal, as negatively valenced categories (e.g., cigarette) often have conflicting goals, and (b) whether ideal items are in fact typical, as they often…

40 CFR 1042.310 - Engine selection for Category 1 and Category 2 engines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Category 2 engines. (a) Determine minimum sample sizes as follows: (1) For Category 1 engines, the minimum sample size is one engine or one percent of the projected U.S.-directed production volume for all your Category 1 engine families, whichever is greater. (2) For Category 2 engines, the minimum sample size is...

Valuation, Categories and Attributes

PubMed Central

Galperin, Inna; Sorenson, Olav

2014-01-01

Existing research on categories has only examined indirectly the value associated with being a member of a category relative to the value of the set of attributes that determine membership in that category. This study uses survey data to analyze consumers' preferences for the "organic” label versus for the attributes underlying that label. We found that consumers generally preferred products with the category label to those with the attributes required for the organic label but without the label. We also found that the value accorded to the organic label increased with the number of attributes that an individual associated with the category. Category membership nevertheless still had greater value than even that of the sum of the attributes associated with it. PMID:25111831

Atomic layer deposition on polymer fibers and fabrics for multifunctional and electronic textiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozena, Alexandra H.; Oldham, Christopher J.; Parsons, Gregory N., E-mail: gnp@ncsu.edu

Textile materials, including woven cotton, polymer knit fabrics, and synthetic nonwoven fiber mats, are being explored as low-cost, flexible, and light-weight platforms for wearable electronic sensing, communication, energy generation, and storage. The natural porosity and high surface area in textiles is also useful for new applications in environmental protection, chemical decontamination, pharmaceutical and chemical manufacturing, catalytic support, tissue regeneration, and others. These applications raise opportunities for new chemistries, chemical processes, biological coupling, and nanodevice systems that can readily combine with textile manufacturing to create new “multifunctional” fabrics. Atomic layer deposition (ALD) has a unique ability to form highly uniform andmore » conformal thin films at low processing temperature on nonuniform high aspect ratio surfaces. Recent research shows how ALD can coat, modify, and otherwise improve polymer fibers and textiles by incorporating new materials for viable electronic and other multifunctional capabilities. This article provides a current overview of the understanding of ALD coating and modification of textiles, including current capabilities and outstanding problems, with the goal of providing a starting point for further research and advances in this field. After a brief introduction to textile materials and current textile treatment methods, the authors discuss unique properties of ALD-coated textiles, followed by a review of recent electronic and multifunctional textiles that use ALD coatings either as direct functional components or as critical nucleation layers for active materials integration. The article concludes with possible future directions for ALD on textiles, including the challenges in materials, manufacturing, and manufacturing integration that must be overcome for ALD to reach its full potential in electronic and other emerging multifunctional textile systems.« less

Category inference as a function of correlational structure, category discriminability, and number of available cues.

PubMed

Lancaster, Matthew E; Shelhamer, Ryan; Homa, Donald

2013-04-01

Two experiments investigated category inference when categories were composed of correlated or uncorrelated dimensions and the categories overlapped minimally or moderately. When the categories minimally overlapped, the dimensions were strongly correlated with the category label. Following a classification learning phase, subsequent transfer required the selection of either a category label or a feature when one, two, or three features were missing. Experiments 1 and 2 differed primarily in the number of learning blocks prior to transfer. In each experiment, the inference of the category label or category feature was influenced by both dimensional and category correlations, as well as their interaction. The number of cues available at test impacted performance more when the dimensional correlations were zero and category overlap was high. However, a minimal number of cues were sufficient to produce high levels of inference when the dimensions were highly correlated; additional cues had a positive but reduced impact, even when overlap was high. Subjects were generally more accurate in inferring the category label than a category feature regardless of dimensional correlation, category overlap, or number of cues available at test. Whether the category label functioned as a special feature or not was critically dependent upon these embedded correlations, with feature inference driven more strongly by dimensional correlations.

Effects of fabric anisotropy on elastic shear modulus of granular soils

NASA Astrophysics Data System (ADS)

Li, Bo; Zeng, Xiangwu

2014-06-01

The fabric anisotropy of a granular soil deposit can strongly influence its engineering properties and behavior. This paper presents the results of a novel experimental study designed to examine the effects of fabric anisotropy on smallstrain stiffness and its evolution with loading on the elastic shear modulus of granular materials under a K 0 condition. Two primary categories of fabric anisotropy, i.e., deposition-induced and particle shape-induced, are investigated. Toyoura sand deposits with relative densities of 40% and 80% were prepared using deposition angles oriented at 0° and 90°. Piezoelectric transducers were used to obtain the elastic shear modulus in the vertical and horizontal directions ( G vh and G hh). The measurements indicate distinct differences in the values of G with respect to the different deposition angles. Particle shapeinduced fabric anisotropy was examined using four selected sands. It was concluded that sphericity is a controlling factor dominating the small-strain stiffness of granular materials. The degree of fabric anisotropy proves to be a good indicatorin the characterization of stress-induced fabric evolution during loading and unloading stress cycles. The experimental data were used to calibrate an existing micromechanical model, which was able to represent the behavior of the granular material and the degree of fabric anisotropy reasonably well.

An efficient process for producing economical and eco-friendly cotton textile composites for mobile industry

USDA-ARS?s Scientific Manuscript database

The mobile industry comprised of airplanes, automotives, and ships uses enormous quantities of various types of textiles. Just a few decades ago, most of these textile products and composites were made with woven or knitted fabrics that were mostly made with the then only available natural fibers, i...

The impact of category structure and training methodology on learning and generalizing within-category representations.

PubMed

Ell, Shawn W; Smith, David B; Peralta, Gabriela; Hélie, Sébastien

2017-08-01

When interacting with categories, representations focused on within-category relationships are often learned, but the conditions promoting within-category representations and their generalizability are unclear. We report the results of three experiments investigating the impact of category structure and training methodology on the learning and generalization of within-category representations (i.e., correlational structure). Participants were trained on either rule-based or information-integration structures using classification (Is the stimulus a member of Category A or Category B?), concept (e.g., Is the stimulus a member of Category A, Yes or No?), or inference (infer the missing component of the stimulus from a given category) and then tested on either an inference task (Experiments 1 and 2) or a classification task (Experiment 3). For the information-integration structure, within-category representations were consistently learned, could be generalized to novel stimuli, and could be generalized to support inference at test. For the rule-based structure, extended inference training resulted in generalization to novel stimuli (Experiment 2) and inference training resulted in generalization to classification (Experiment 3). These data help to clarify the conditions under which within-category representations can be learned. Moreover, these results make an important contribution in highlighting the impact of category structure and training methodology on the generalization of categorical knowledge.

Comprehensive mechanical characterization of PLA fabric combined with PCL to form a composite structure vascular graft.

PubMed

Li, Chaojing; Wang, Fujun; Douglas, Graeham; Zhang, Ze; Guidoin, Robert; Wang, Lu

2017-05-01

Vascular grafts made by tissue engineering processes are prone to buckling and twisting, which can impede blood flow and lead to collapse of the vessel. These vascular conduits may suffer not only from insufficient tensile strength, but also from vulnerabilities related to compression, torsion, and pulsatile pressurization. Aiming to develop a tissue engineering-inspired blood conduit, composite vascular graft (cVG) prototypes were created by combining a flexible polylactic acid (PLA) knitted fabric with a soft polycaprolactone (PCL) matrix. The graft is to be populated in-situ with cellular migration and proliferation into the device. Comprehensive characterizations probed the relationship between structure and mechanical properties of the different cVG prototypes. The composite grafts exhibited major improvements in mechanical characteristics compared to single-material devices, with particular improvement in compression and torsional resistance. A commercial expanded polytetrafluoroethylene (ePTFE) vascular graft was used as a control against the proposed composite vascular grafts. CVG devices showed high tensile strength, high bursting strength, and improved suture retention. Compression, elastic recovery, and compliance were similar to those for the ePTFE graft. Copyright © 2016 Elsevier Ltd. All rights reserved.

Children's Category-Based Inferences Affect Classification

ERIC Educational Resources Information Center

Ross, Brian H.; Gelman, Susan A.; Rosengren, Karl S.

2005-01-01

Children learn many new categories and make inferences about these categories. Much work has examined how children make inferences on the basis of category knowledge. However, inferences may also affect what is learned about a category. Four experiments examine whether category-based inferences during category learning influence category knowledge…

Fracture Behavior of a Stitched Warp-Knit Carbon Fabric Composite

NASA Technical Reports Server (NTRS)

Poe, Clarence C., Jr.; Reeder, James R.; Yuan, F. G.

2001-01-01

Tests were conducted on several types of fracture specimens made from a carbon/epoxy composite. The composite material was stitched prior to introducing epoxy resin. Boeing, used this material to develop a composite wing box for a transport aircraft in the NASA Advanced Composites Transport Program. The specimens included compact, extended compact, and center notched tension specimens. The specimens were cut from panels with three orientations in order to explore the effects of anisotropy. The panels were made with various thicknesses to represent a wing, skin from tip to root. All fractures were not self-similar depending on specimen type and orientation. Unnotched tension specimens were also tested to measure elastic constants and strengths. The normal and shear strains were calculated on fracture planes using a series representation of strain fields for plane anisotropic crack problems. The fracture parameters were determined using a finite element method. Characteristic distances for critical tension and shear strains were calculated for each specimen and a failure criterion based on the interaction of tension and shear strains was proposed.

Encoding tasks dissociate the effects of divided attention on category-cued recall and category-exemplar generation.

PubMed

Parker, Andrew; Dagnall, Neil; Munley, Gary

2012-01-01

The combined effects of encoding tasks and divided attention upon category-exemplar generation and category-cued recall were examined. Participants were presented with pairs of words each comprising a category name and potential example of that category. They were then asked to indicate either (i) their liking for both of the words or (ii) if the exemplar was a member of the category. It was found that divided attention reduced performance on the category-cued recall task under both encoding conditions. However, performance on the category-exemplar generation task remained invariant across the attention manipulation following the category judgment task. This provides further evidence that the processes underlying performance on conceptual explicit and implicit memory tasks can be dissociated, and that the intentional formation of category-exemplar associations attenuates the effects of divided attention on category-exemplar generation.

Culture, category salience, and inductive reasoning.

PubMed

Choi, I; Nisbett, R E; Smith, E E

1997-12-01

The role of category salience in category-based induction was demonstrated in two ways: (i) temporarily increasing category salience facilitated category-based induction, and (ii) this effect was moderated by cultural differences that we predicted would be related to chronic category salience. Subjects for whom categories were presumed to be more accessible (Americans) were not as much influenced by manipulations to increase category salience as subjects who were presumed to have lower chronic accessibility of categories (Koreans). However, as anticipated, this pattern was reversed for inferences about behavioral properties of social categories. Due to the 'interdependent' nature of their culture, Koreans presumably have relatively higher chronic accessibility for social categories than do relatively 'independent' Americans, and hence were not influenced as much by increasing category salience.

Advanced Clothing Studies

NASA Technical Reports Server (NTRS)

Orndoff, Evelyne; Poritz, Darwin

2014-01-01

All human space missions require significant logistical mass and volume that add an unprecedented burden on longduration missions beyond low-Earth orbit. For these missions with limited cleaning resources, a new wardrobe must be developed to reduce this logistical burden by reducing clothing mass and extending clothing wear. The present studies have been undertaken, for the first time, to measure length of wear and to assess the acceptance of such extended wear. Garments in these studies are commercially available exercise T-shirts and shorts, routine-wear T-shirts, and longsleeved pullover shirts. Fabric composition (cotton, polyester, light-weight, superfine Merino wool, modacrylic, cotton/rayon, polyester/Cocona, modacrylic/Xstatic, modacrylic/rayon, modacrylic/lyocell/aramid), construction (open knit, tight knit, open weave, tight weave), and finishing treatment (none, quaternary ammonium salt) are the independent variables. Eleven studies are reported here: five studies of exercise T-shirts, three of exercise shorts, two of routine wear Tshirts, and one of shirts used as sleep-wear. All studies are conducted in a climate-controlled environment, similar to a space vehicle's. For exercise clothing, study participants wear the garments during aerobic exercise. For routine wear clothing, study participants wear the T-shirts daily in an office or laboratory. Daily questionnaires collected data on ordinal preferences of nine sensory elements and on reason for retiring a used garment. Study 1 compares knitted cotton, polyester, and Merino exercise T-shirts (61 participants), study 2, knitted polyester, modacrylic, and polyester/Cocona exercise T-shirts (40 participants), study 3, cotton and polyester exercise shorts, knitted and woven (70 participants), all three using factorial experimental designs with and without a finishing treatment, conducted at the Johnson Space Center, sharing study participants. Study 4 compares knitted polyester and ZQ Merino exercise T

Category and stereotype activation revisited.

PubMed

Akrami, Nazar; Ekehammar, Bo; Araya, Tadesse

2006-12-01

In Study 1 (N= 230), we found that the participants' explicit prejudice was not related to their knowledge of cultural stereotypes of immigrants in Sweden, and that they associated the social category immigrants with the same national/ethnic categories. In Study 2 (N= 88), employing the category and stereotype words obtained in Study 1 as primes, we examined whether participants with varying degrees of explicit prejudice differed in their automatic stereotyping and implicit prejudice when primed with category or stereotypical words. In accord with our hypothesis, and contrary to previous findings, the results showed that people's explicit prejudice did not affect their automatic stereotyping and implicit prejudice, neither in the category nor stereotype priming condition. Study 3 (N= 62), employing category priming using facial photographs of Swedes and immigrants as primes, showed that participants' implicit prejudice was not moderated by their explicit prejudice. The outcome is discussed in relation to the distinction between category and stereotype priming and in terms of the associative strength between a social category and its related stereotypes.

From industrially weavable and knittable highly conductive yarns to large wearable energy storage textiles.

PubMed

Huang, Yan; Hu, Hong; Huang, Yang; Zhu, Minshen; Meng, Wenjun; Liu, Chang; Pei, Zengxia; Hao, Chonglei; Wang, Zuankai; Zhi, Chunyi

2015-05-26

Wearable electronic textiles that store capacitive energy are a next frontier in personalized electronics. However, the lack of industrially weavable and knittable conductive yarns in conjunction with high capacitance, limits the wide-scale application of such textiles. Here pristine soft conductive yarns are continuously produced by a scalable method with the use of twist-bundle-drawing technique, and are mechanically robust enough to be knitted to a cloth by a commercial cloth knitting machine. Subsequently, the reduced-graphene-oxide-modified conductive yarns covered with a hierarchical structure of MnO2 nanosheets and a polypyrrole thin film were used to fabricate weavable, knittable and wearable yarn supercapacitors. The resultant modified yarns exhibit specific capacitances as high as 36.6 mF cm(-1) and 486 mF cm(-2) in aqueous electrolyte (three-electrode cell) or 31 mF cm(-1) and 411 mF cm(-2) in all solid-state two-electrode cell. The symmetric solid-state supercapacitor has high energy densities of 0.0092 mWh cm(-2) and 1.1 mWh cm(-3) (both normalized to the whole device) with a long cycle life. Large energy storage textiles are fabricated by weaving our flexible all-solid-state supercapacitor yarns to a 15 cm × 10 cm cloth on a loom and knitting in a woollen wrist band to form a pattern, enabling dual functionalities of energy storage capability and wearability.

Design and fabrication of giant micromirrors using electroplating-based technology

NASA Astrophysics Data System (ADS)

Ilias, Samir; Topart, Patrice A.; Larouche, Carl; Leclair, Sebastien; Jerominek, Hubert

2005-01-01

Giant micromirrors with large scanning deflection and good flatness are required for many space and terrestrial applications. A novel approach to manufacturing this category of micromirrors is proposed. The approach combines selective electroplating and flip-chip based technologies. It allows for large air gaps, flat and smooth active micromirror surfaces and permits independent fabrication of the micromirrors and control electronics, avoiding temperature and sacrificial layer incompatibilities between them. In this work, electrostatically actuated piston and torsion micromirrors were designed and simulated. The simulated structures were designed to allow large deflection, i.e. piston displacement larger than 10 um and torsional deflection up to 35°. To achieve large micromirror deflections, up to seventy micron-thick resists were used as a micromold for nickel and solder electroplating. Smooth micromirror surfaces (roughness lower than 5 nm rms) and large radius of curvature (R as large as 23 cm for a typical 1000x1000 um2 micromirror fabricated without address circuits) were achieved. A detailed fabrication process is presented. First piston mirror prototypes were fabricated and a preliminary evaluation of static deflection of a piston mirror is presented.

19 CFR 10.882 - Goods eligible for tariff preference claims.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Oman... knit to shape, or both, and sewn or otherwise assembled in the territory of Oman from fabric or yarn produced or obtained outside the territory of Oman or the United States are eligible for a TPL claim filed...

19 CFR 10.882 - Goods eligible for tariff preference claims.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Oman... knit to shape, or both, and sewn or otherwise assembled in the territory of Oman from fabric or yarn produced or obtained outside the territory of Oman or the United States are eligible for a TPL claim filed...

19 CFR 10.882 - Goods eligible for tariff preference claims.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Oman... knit to shape, or both, and sewn or otherwise assembled in the territory of Oman from fabric or yarn produced or obtained outside the territory of Oman or the United States are eligible for a TPL claim filed...

19 CFR 10.882 - Goods eligible for tariff preference claims.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Oman... knit to shape, or both, and sewn or otherwise assembled in the territory of Oman from fabric or yarn produced or obtained outside the territory of Oman or the United States are eligible for a TPL claim filed...

75 FR 47494 - Implementation Guidance for Physical Protection of Byproduct Material; Category 1 and Category 2...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-06

... for Physical Protection of Byproduct Material; Category 1 and Category 2 Quantities of Radioactive... on the draft implementation guidance for proposed 10 CFR part 37 Physical Protection of Byproduct... proposed 10 CFR part 37, Physical Protection of Byproduct Material, specifically Category 1 and Category 2...

Treatment of category generation and retrieval in aphasia: Effect of typicality of category items.

PubMed Central

Kiran, Swathi; Sandberg, Chaleece; Sebastian, Rajani

2011-01-01

Purpose: Kiran and colleagues (Kiran, 2007, 2008; Kiran & Johnson, 2008; Kiran & Thompson, 2003) have previously suggested that training atypical examples within a semantic category is a more efficient treatment approach to facilitating generalization within the category than training typical examples. The present study extended our previous work examining the notion of semantic complexity within goal-derived (ad-hoc) categories in individuals with aphasia. Methods: Six individuals with fluent aphasia (range = 39-84 years) and varying degrees of naming deficits and semantic impairments were involved. Thirty typical and atypical items each from two categories were selected after an extensive stimulus norming task. Generative naming for the two categories was tested during baseline and treatment. Results: As predicted, training atypical examples in the category resulted in generalization to untrained typical examples in five out the five patient-treatment conditions. In contrast, training typical examples (which was in examined three conditions) produced mixed results. One patient showed generalization to untrained atypical examples, whereas two patients did not show generalization to untrained atypical examples. Conclusions: Results of the present study supplement our existing data on the effect of a semantically based treatment for lexical retrieval by manipulating the typicality of category exemplars. PMID:21173393

Conceptual influences on category-based induction

PubMed Central

Gelman, Susan A.; Davidson, Natalie S.

2013-01-01

One important function of categories is to permit rich inductive inferences. Prior work shows that children use category labels to guide their inductive inferences. However, there are competing theories to explain this phenomenon, differing in the roles attributed to conceptual information versus perceptual similarity. Seven experiments with 4- to 5-year-old children and adults (N = 344) test these theories by teaching categories for which category membership and perceptual similarity are in conflict, and varying the conceptual basis of the novel categories. Results indicate that for non-natural kind categories that have little conceptual coherence, children make inferences based on perceptual similarity, whereas adults make inferences based on category membership. In contrast, for basic- and ontological-level categories that have a principled conceptual basis, children and adults alike make use of category membership more than perceptual similarity as the basis of their inferences. These findings provide evidence in favor of the role of conceptual information in preschoolers’ inferences, and further demonstrate that labeled categories are not all equivalent; they differ in their inductive potential. PMID:23517863

Intrinsically Stretchable and Conductive Textile by a Scalable Process for Elastic Wearable Electronics.

PubMed

Wang, Chunya; Zhang, Mingchao; Xia, Kailun; Gong, Xueqin; Wang, Huimin; Yin, Zhe; Guan, Baolu; Zhang, Yingying

2017-04-19

The prosperous development of stretchable electronics poses a great demand on stretchable conductive materials that could maintain their electrical conductivity under tensile strain. Previously reported strategies to obtain stretchable conductors usually involve complex structure-fabricating processes or utilization of high-cost nanomaterials. It remains a great challenge to produce stretchable and conductive materials via a scalable and cost-effective process. Herein, a large-scalable pyrolysis strategy is developed for the fabrication of intrinsically stretchable and conductive textile in utilizing low-cost and mass-produced weft-knitted textiles as raw materials. Due to the intrinsic stretchability of the weft-knitted structure and the excellent mechanical and electrical properties of the as-obtained carbonized fibers, the obtained flexible and durable textile could sustain tensile strains up to 125% while keeping a stable electrical conductivity (as shown by a Modal-based textile), thus ensuring its applications in elastic electronics. For demonstration purposes, stretchable supercapacitors and wearable thermal-therapy devices that showed stable performance with the loading of tensile strains have been fabricated. Considering the simplicity and large scalability of the process, the low-cost and mass production of the raw materials, and the superior performances of the as-obtained elastic and conductive textile, this strategy would contribute to the development and industrial production of wearable electronics.

Pre-Flight Advanced Clothing Study

NASA Technical Reports Server (NTRS)

Orndoff, Evelyne; Poritz, Darwin; Schlesinger, Thilini; Byme, Vicky

2014-01-01

All human space missions require significant logistical mass and volume that will become an excessive burden for long duration missions beyond low Earth orbit. The current International Space Station (ISS) crew wardrobe has already evolved not only to reduce some of the logistical burden but also to address crew preference. The present study was undertaken to find ways further to reduce this logistical burden while examining human response to different types of clothes. The primary objective of the study is to measure how long people can wear the same exercise garment, depending on the type of fabric and the presence of antimicrobial treatment. The secondary objective is to assess the reasons for length of wear from perceptions of clothing characteristics, including nine ordinal scales. Cardiovascular exercise was chosen as the activity in this experiment for its profuse sweating effect and because it is considered a more severe treatment applied to the clothes than every-day usage. Study garments were exercise T-shirts and shorts purchased from various vendors. Fabric construction, fabric composition, and finishing treatment were defined as the key variables. A web-based questionnaire was used for self-reported data collection. The study was divided in three balanced experiments: a cotton-polyester-wool (CPW) T-shirts study with 61 participants, a polyester-modacrylic-polyester/cocona (PMC) T-shirts study with 40 participants, and a shorts study with 70 participants. In the CPW study, the T-shirts were made of 100% cotton, or of 100% polyester or of 100% wool, and categorized into open and tight knit constructions. In the PMC study, the T-shirts were made of 100% polyester, or of 82% modacrylic, or of 95% polyester with 5% cocona fiber, without construction distinction. The shorts were made either of 100% cotton or of 100% polyester, and were knitted or woven. Some garments were treated with Bio-Protect 500 antimicrobial finish according the experimental design

Employers' Guide to Grants Scheme, 1969/70.

ERIC Educational Resources Information Center

Knitting, Lace, and Net Industry Training Board, Nottingham (England).

This booklet gives details, approved by the British Secretary of State for Employment and Productivity, of grants which will be paid by the Knitting, Lace, and Net Industry Board for training and further education during the training year, 1 August 1969-31 July 1970. Two categories are stressed: (1) day, block, release, and full time courses and…

Ego depletion interferes with rule-defined category learning but not non-rule-defined category learning.

PubMed

Minda, John P; Rabi, Rahel

2015-01-01

Considerable research on category learning has suggested that many cognitive and environmental factors can have a differential effect on the learning of rule-defined (RD) categories as opposed to the learning of non-rule-defined (NRD) categories. Prior research has also suggested that ego depletion can temporarily reduce the capacity for executive functioning and cognitive flexibility. The present study examined whether temporarily reducing participants' executive functioning via a resource depletion manipulation would differentially impact RD and NRD category learning. Participants were either asked to write a story with no restrictions (the control condition), or without using two common letters (the ego depletion condition). Participants were then asked to learn either a set of RD categories or a set of NRD categories. Resource depleted participants performed more poorly than controls on the RD task, but did not differ from controls on the NRD task, suggesting that self regulatory resources are required for successful RD category learning. These results lend support to multiple systems theories and clarify the role of self-regulatory resources within this theory.

Ego depletion interferes with rule-defined category learning but not non-rule-defined category learning

PubMed Central

Minda, John P.; Rabi, Rahel

2015-01-01

Considerable research on category learning has suggested that many cognitive and environmental factors can have a differential effect on the learning of rule-defined (RD) categories as opposed to the learning of non-rule-defined (NRD) categories. Prior research has also suggested that ego depletion can temporarily reduce the capacity for executive functioning and cognitive flexibility. The present study examined whether temporarily reducing participants’ executive functioning via a resource depletion manipulation would differentially impact RD and NRD category learning. Participants were either asked to write a story with no restrictions (the control condition), or without using two common letters (the ego depletion condition). Participants were then asked to learn either a set of RD categories or a set of NRD categories. Resource depleted participants performed more poorly than controls on the RD task, but did not differ from controls on the NRD task, suggesting that self regulatory resources are required for successful RD category learning. These results lend support to multiple systems theories and clarify the role of self-regulatory resources within this theory. PMID:25688220

Color categories only affect post-perceptual processes when same- and different-category colors are equally discriminable.

PubMed

He, Xun; Witzel, Christoph; Forder, Lewis; Clifford, Alexandra; Franklin, Anna

2014-04-01

Prior claims that color categories affect color perception are confounded by inequalities in the color space used to equate same- and different-category colors. Here, we equate same- and different-category colors in the number of just-noticeable differences, and measure event-related potentials (ERPs) to these colors on a visual oddball task to establish if color categories affect perceptual or post-perceptual stages of processing. Category effects were found from 200 ms after color presentation, only in ERP components that reflect post-perceptual processes (e.g., N2, P3). The findings suggest that color categories affect post-perceptual processing, but do not affect the perceptual representation of color.

A review on utilization of textile composites in transportation towards sustainability

NASA Astrophysics Data System (ADS)

Aly, Nermin M.

2017-10-01

Transportation industry is rapidly developing owing to its size and importance which affects on various aspects of life. It includes all the transport means that facilitate mobility of people or goods either by air, land or sea like aircrafts, automotives, ships, trains, etc. The utilization of textiles in this industry is increasing as a result of moving towards achieving sustainability and enhancing performance, comfort and safety. Through substituting heavier materials with textiles of high performance specifications and textile reinforced composites to reduce weight, fuel consumption and CO2 emissions. Composite materials can fulfil the demands for sustainability in the transportation sector through using renewable, recycled and lightweight materials, considering the requirements of each category of transport vehicles. Textiles used in reinforcing composites are diverse including fibers, yarns or fabric preforms such as woven, nonwoven, knitted, braided which varies from 2D to complex 3D structures. This paper presents a brief review on the utilization of textiles in reinforcing composites for various transportation applications to achieve sustainability. Also, discussing the influence of textiles structural parameters like fiber material properties, fabric production technique and construction on their mechanical behaviour. Focusing on researches findings in this area and highlighting some prospects for further developments domestically.

The composition of category conjunctions.

PubMed

Hutter, Russell R C; Crisp, Richard J

2005-05-01

In three experiments, the authors investigated the impression formation process resulting from the perception of familiar or unfamiliar social category combinations. In Experiment 1, participants were asked to generate attributes associated with either a familiar or unfamiliar social category conjunction. Compared to familiar combinations, the authors found that when the conjunction was unfamiliar, participants formed their impression less from the individual constituent categories and relatively more from novel emergent attributes. In Experiment 2, the authors replicated this effect using alternative experimental materials. In Experiment 3, the effect generalized to additional (orthogonally combined) gender and occupation categories. The implications of these findings for understanding the processes involved in the conjunction of social categories, and the formation of new stereotypes, are discussed.

Simplicial Descent Categories

NASA Astrophysics Data System (ADS)

Rodriguez Gonzalez, Beatriz

2008-04-01

Much of the homotopical and homological structure of the categories of chain complexes and topological spaces can be deduced from the existence and properties of the 'simple' functors Tot : {double chain complexes} -> {chain complexes} and geometric realization : {sSets} -> {Top}, or similarly, Tot : {simplicial chain complexes} -> {chain complexes} and | | : {sTop} -> {Top}. The purpose of this thesis is to abstract this situation, and to this end we introduce the notion of '(co)simplicial descent category'. It is inspired by Guillen-Navarros's '(cubical) descent categories'. The key ingredients in a (co)simplicial descent category D are a class E of morphisms in D, called equivalences, and a 'simple' functor s : {(co)simplicial objects in D} -> D. They must satisfy axioms like 'Eilenberg-Zilber', 'exactness' and 'acyclicity'. This notion covers a wide class of examples, as chain complexes, sSets, topological spaces, filtered cochain complexes (where E = filtered quasi-isomorphisms or E = E_2-isomorphisms), commutative differential graded algebras (with s = Navarro's Thom-Whitney simple), DG-modules over a DG-category and mixed Hodge complexes, where s = Deligne's simple. From the simplicial descent structure we obtain homotopical structure on D, as cone and cylinder objects. We use them to i) explicitly describe the morphisms of HoD=D[E^{-1}] similarly to the case of calculus of fractions; ii) endow HoD with a non-additive pre-triangulated structure, that becomes triangulated in the stable additive case. These results use the properties of a 'total functor', which associates to any biaugmented bisimplicial object a simplicial object. It is the simplicial analogue of the total chain complex of a double complex, and it is left adjoint to Illusie's 'decalage' functor.

14 CFR 23.3 - Airplane categories.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Airplane categories. 23.3 Section 23.3... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES General § 23.3 Airplane categories. (a) The normal category is limited to airplanes that have a seating configuration, excluding pilot...

14 CFR 23.3 - Airplane categories.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Airplane categories. 23.3 Section 23.3... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES General § 23.3 Airplane categories. (a) The normal category is limited to airplanes that have a seating configuration, excluding pilot...

14 CFR 23.3 - Airplane categories.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Airplane categories. 23.3 Section 23.3... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES General § 23.3 Airplane categories. (a) The normal category is limited to airplanes that have a seating configuration, excluding pilot...

14 CFR 23.3 - Airplane categories.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Airplane categories. 23.3 Section 23.3... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES General § 23.3 Airplane categories. (a) The normal category is limited to airplanes that have a seating configuration, excluding pilot...

Models as Relational Categories

NASA Astrophysics Data System (ADS)

Kokkonen, Tommi

2017-11-01

Model-based learning (MBL) has an established position within science education. It has been found to enhance conceptual understanding and provide a way for engaging students in authentic scientific activity. Despite ample research, few studies have examined the cognitive processes regarding learning scientific concepts within MBL. On the other hand, recent research within cognitive science has examined the learning of so-called relational categories. Relational categories are categories whose membership is determined on the basis of the common relational structure. In this theoretical paper, I argue that viewing models as relational categories provides a well-motivated cognitive basis for MBL. I discuss the different roles of models and modeling within MBL (using ready-made models, constructive modeling, and generative modeling) and discern the related cognitive aspects brought forward by the reinterpretation of models as relational categories. I will argue that relational knowledge is vital in learning novel models and in the transfer of learning. Moreover, relational knowledge underlies the coherent, hierarchical knowledge of experts. Lastly, I will examine how the format of external representations may affect the learning of models and the relevant relations. The nature of the learning mechanisms underlying students' mental representations of models is an interesting open question to be examined. Furthermore, the ways in which the expert-like knowledge develops and how to best support it is in need of more research. The discussion and conceptualization of models as relational categories allows discerning students' mental representations of models in terms of evolving relational structures in greater detail than previously done.

Data categories for marine planning

USGS Publications Warehouse

Lightsom, Frances L.; Cicchetti, Giancarlo; Wahle, Charles M.

2015-01-01

The U.S. National Ocean Policy calls for a science- and ecosystem-based approach to comprehensive planning and management of human activities and their impacts on America’s oceans. The Ocean Community in Data.gov is an outcome of 2010–2011 work by an interagency working group charged with designing a national information management system to support ocean planning. Within the working group, a smaller team developed a list of the data categories specifically relevant to marine planning. This set of categories is an important consensus statement of the breadth of information types required for ocean planning from a national, multidisciplinary perspective. Although the categories were described in a working document in 2011, they have not yet been fully implemented explicitly in online services or geospatial metadata, in part because authoritative definitions were not created formally. This document describes the purpose of the data categories, provides definitions, and identifies relations among the categories and between the categories and external standards. It is intended to be used by ocean data providers, managers, and users in order to provide a transparent and consistent framework for organizing and describing complex information about marine ecosystems and their connections to humans.

Improving menu categories.

PubMed

2004-09-01

No matter how good a site's navigational tools, site visitors will not use them if the menu categories are ambiguous. Users have to know what to expect when they click on a particular menu item. If the categories are not intuitive, users will have to resort to the site's search engine, ignoring the entire structure. The Pennsylvania Medical Society site (http://www.pamedsoc.org) had been plagued with poor menu labels until it took a step back and improved them.

Categories and Music Transmission

ERIC Educational Resources Information Center

Gatien, Greg

2009-01-01

Lucy Green's (2008) "Music, Informal Learning, and the School: A New Classroom Pedagogy" gives rise to an interesting corollary. Does the manner of music's transmission inform one's understanding of a musical category? While categories of music can be difficult to define according to strict musical characteristics, a better understanding of…

78 FR 16661 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-18

... fabric). Overall weight: 287-351 grams per square meter. Overall width: Selvedge: 150.4-154.4 cm; Minimum... per cm x 43-45 picks per cm Weight: 121.5-148.5 grams per square meter Width: Selvedge: 150.4-154.4 cm... yarns: filament Knitting gauge: 27-29 Weight: 140.4-171.6 grams per square meter Width: Selvedge: 150.4...

Incremental Bayesian Category Learning From Natural Language.

PubMed

Frermann, Lea; Lapata, Mirella

2016-08-01

Models of category learning have been extensively studied in cognitive science and primarily tested on perceptual abstractions or artificial stimuli. In this paper, we focus on categories acquired from natural language stimuli, that is, words (e.g., chair is a member of the furniture category). We present a Bayesian model that, unlike previous work, learns both categories and their features in a single process. We model category induction as two interrelated subproblems: (a) the acquisition of features that discriminate among categories, and (b) the grouping of concepts into categories based on those features. Our model learns categories incrementally using particle filters, a sequential Monte Carlo method commonly used for approximate probabilistic inference that sequentially integrates newly observed data and can be viewed as a plausible mechanism for human learning. Experimental results show that our incremental learner obtains meaningful categories which yield a closer fit to behavioral data compared to related models while at the same time acquiring features which characterize the learned categories. (An earlier version of this work was published in Frermann and Lapata .). Copyright © 2015 Cognitive Science Society, Inc.

Right away: A late, right-lateralized category effect complements an early, left-lateralized category effect in visual search.

PubMed

Constable, Merryn D; Becker, Stefanie I

2017-10-01

According to the Sapir-Whorf hypothesis, learned semantic categories can influence early perceptual processes. A central finding in support of this view is the lateralized category effect-namely, the finding that categorically different colors (e.g., blue and green hues) can be discriminated faster than colors within the same color category (e.g., different hues of green), especially when they are presented in the right visual field. Because the right visual field projects to the left hemisphere, this finding has been popularly couched in terms of the left-lateralization of language. However, other studies have reported bilateral category effects, which has led some researchers to question the linguistic origins of the effect. Here we examined the time course of lateralized and bilateral category effects in the classical visual search paradigm by means of eyetracking and RT distribution analyses. Our results show a bilateral category effect in the manual responses, which is combined of an early, left-lateralized category effect and a later, right-lateralized category effect. The newly discovered late, right-lateralized category effect occurred only when observers had difficulty locating the target, indicating a specialization of the right hemisphere to find categorically different targets after an initial error. The finding that early and late stages of visual search show different lateralized category effects can explain a wide range of previously discrepant findings.

The helpfulness of category labels in semi-supervised learning depends on category structure.

PubMed

Vong, Wai Keen; Navarro, Daniel J; Perfors, Amy

2016-02-01

The study of semi-supervised category learning has generally focused on how additional unlabeled information with given labeled information might benefit category learning. The literature is also somewhat contradictory, sometimes appearing to show a benefit to unlabeled information and sometimes not. In this paper, we frame the problem differently, focusing on when labels might be helpful to a learner who has access to lots of unlabeled information. Using an unconstrained free-sorting categorization experiment, we show that labels are useful to participants only when the category structure is ambiguous and that people's responses are driven by the specific set of labels they see. We present an extension of Anderson's Rational Model of Categorization that captures this effect.

14 CFR 23.3 - Airplane categories.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Airplane categories. 23.3 Section 23.3... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES General § 23.3 Airplane categories... airplanes that have a seating configuration, excluding pilot seats, of nine or less, a maximum certificated...

14 CFR 29.79 - Landing: Category A.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Landing: Category A. 29.79 Section 29.79... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.79 Landing: Category A. (a) For Category A rotorcraft— (1) The landing performance must be determined and scheduled so that if the critical engine fails...

Typicality Mediates Performance during Category Verification in Both Ad-Hoc and Well-Defined Categories

ERIC Educational Resources Information Center

Sandberg, Chaleece; Sebastian, Rajani; Kiran, Swathi

2012-01-01

Background: The typicality effect is present in neurologically intact populations for natural, ad-hoc, and well-defined categories. Although sparse, there is evidence of typicality effects in persons with chronic stroke aphasia for natural and ad-hoc categories. However, it is unknown exactly what influences the typicality effect in this…

Limits of Generalization between Categories and Implications for Theories of Category Specificity

PubMed Central

Bukach, Cindy M.; Phillips, W. Stewart; Gauthier, Isabel

2010-01-01

Both domain-specific and expertise accounts of category specialization assume that generalization occurs within a domain but not between domains. Yet it is often difficult to define the boundaries and critical features of object domains. Differences in how categories are defined make it difficult to adjudicate between accounts of category specificity and may lead to contradictory results. For example, evidence for whether car experts recruit the fusiform face area is mixed and this inconsistency may be due to the inclusion of antique cars in one of the studies. The current study tested the generalization of expertise from modern to antique cars and found that modern car experts showed expert discrimination and holistic processing of modern cars, but not antique cars. These findings suggest that the neural specialization underlying perceptual expertise is highly specific and may not generalize to distinct subclasses, even when they share some degree of perceptual and conceptual features. PMID:20952784

Tensor functors between Morita duals of fusion categories

NASA Astrophysics Data System (ADS)

Galindo, César; Plavnik, Julia Yael

2017-03-01

Given a fusion category C and an indecomposable C -module category M , the fusion category C^*_{_{M}} of C-module endofunctors of M is called the (Morita) dual fusion category of C with respect to M . We describe tensor functors between two arbitrary duals C^*_{_{M}} and D^*_N in terms of data associated to C and D . We apply the results to G-equivariantizations of fusion categories and group-theoretical fusion categories. We describe the orbits of the action of the Brauer-Picard group on the set of module categories and we propose a categorification of the Rosenberg-Zelinsky sequence for fusion categories.

Prior knowledge of category size impacts visual search.

PubMed

Wu, Rachel; McGee, Brianna; Echiverri, Chelsea; Zinszer, Benjamin D

2018-03-30

Prior research has shown that category search can be similar to one-item search (as measured by the N2pc ERP marker of attentional selection) for highly familiar, smaller categories (e.g., letters and numbers) because the finite set of items in a category can be grouped into one unit to guide search. Other studies have shown that larger, more broadly defined categories (e.g., healthy food) also can elicit N2pc components during category search, but the amplitude of these components is typically attenuated. Two experiments investigated whether the perceived size of a familiar category impacts category and exemplar search. We presented participants with 16 familiar company logos: 8 from a smaller category (social media companies) and 8 from a larger category (entertainment/recreation manufacturing companies). The ERP results from Experiment 1 revealed that, in a two-item search array, search was more efficient for the smaller category of logos compared to the larger category. In a four-item search array (Experiment 2), where two of the four items were placeholders, search was largely similar between the category types, but there was more attentional capture by nontarget members from the same category as the target for smaller rather than larger categories. These results support a growing literature on how prior knowledge of categories affects attentional selection and capture during visual search. We discuss the implications of these findings in relation to assessing cognitive abilities across the lifespan, given that prior knowledge typically increases with age. © 2018 Society for Psychophysiological Research.

Knitted radar absorbing materials (RAM) based on nickel-cobalt magnetic materials

NASA Astrophysics Data System (ADS)

Teber, Ahmet; Unver, Ibrahim; Kavas, Huseyin; Aktas, Bekir; Bansal, Rajeev

2016-05-01

There has been a long-standing interest in the development of flexible, lightweight, thin, and reconfigurable radar absorbing materials (RAM) for military applications such as camouflaging ground-based hardware against airborne radar observation. The use of polymeric Polyacrylonitrile (PAN) fabrics as a host matrix for magnetic metal nano-particles (either at the yarn-stage or after weaving the fabric) for shielding and absorbing applications has been described in the literature. In our experimental investigation, the relative concentrations of Nickel and Cobalt as well as the coating time are varied with a view to optimizing the microwave absorption characteristics of the resulting PAN-based composite material in the radar-frequency bands (X, Ku, and K). It is found that the PAN samples with the shortest coating time have the best return losses (under -20 dB return loss over a moderate bandwidth).

Human Category Learning 2.0

PubMed Central

Ashby, F. Gregory; Maddox, W. Todd

2010-01-01

During the 1990’s and early 2000’s, cognitive neuroscience investigations of human category learning focused on the primary goal of showing that humans have multiple category learning systems and on the secondary goals of identifying key qualitative properties of each system and of roughly mapping out the neural networks that mediate each system. Many researchers now accept the strength of the evidence supporting multiple systems, and as a result, during the past few years, work has begun on the second generation of research questions – that is, on questions that begin with the assumption that humans have multiple category learning systems. This article reviews much of this second generation of research. Topics covered include: 1) How do the various systems interact? 2) Are there different neural systems for categorization and category representation? 3) How does automaticity develop in each system?, and 4) Exactly how does each system learn? PMID:21182535

Human category learning 2.0.

PubMed

Ashby, F Gregory; Maddox, W Todd

2011-04-01

During the 1990s and early 2000s, cognitive neuroscience investigations of human category learning focused on the primary goal of showing that humans have multiple category-learning systems and on the secondary goals of identifying key qualitative properties of each system and of roughly mapping out the neural networks that mediate each system. Many researchers now accept the strength of the evidence supporting multiple systems, and as a result, during the past few years, work has begun on the second generation of research questions-that is, on questions that begin with the assumption that humans have multiple category-learning systems. This article reviews much of this second generation of research. Topics covered include (1) How do the various systems interact? (2) Are there different neural systems for categorization and category representation? (3) How does automaticity develop in each system? and (4) Exactly how does each system learn? © 2010 New York Academy of Sciences.

A Probabilistic Account of Exemplar and Category Generation

ERIC Educational Resources Information Center

Jern, Alan; Kemp, Charles

2013-01-01

People are capable of imagining and generating new category exemplars and categories. This ability has not been addressed by previous models of categorization, most of which focus on classifying category exemplars rather than generating them. We develop a formal account of exemplar and category generation which proposes that category knowledge is…

40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... from research engines or similar engine models that are already in production. Your demonstration must... Category 1 engines and Category 2 engines. 1042.101 Section 1042.101 Protection of Environment... MARINE COMPRESSION-IGNITION ENGINES AND VESSELS Emission Standards and Related Requirements § 1042.101...

Reconceptualizing 'extremism' and 'moderation': from categories of analysis to categories of practice in the construction of collective identity.

PubMed

Hopkins, Nick; Kahani-Hopkins, Vered

2009-03-01

Much psychological research employs the categories of extremism and moderation as categories of analysis (e.g. to identify the psychological bases for, and consequences of, holding certain positions). This paper argues these categorizations inevitably reflect one's values and taken-for-granted assumptions about social reality and that their use as analytic categories limits our ability to explore what is really important: social actors' own constructions of social reality. In turn we argue that if we are to focus on this latter, there may be merit in exploring how social actors themselves use the categories of moderation and extremism to construct their own terms of reference. That is we propose to re-conceptualize the categories of moderation and extremism as categories of practice rather than analysis. The utility of this approach is illustrated with qualitative data. We argue that these data illustrate the importance of respecting social actors' own constructions of social reality (rather than imposing our own). Moreover, we argue that categories of moderation and extremism may be employed by social actors in diverse ways to construct different terms of reference and so recruit support for different identity-related projects.

40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... information equivalent to such in-use data, such as data from research engines or similar engine models that... Category 1 engines and Category 2 engines. 1042.101 Section 1042.101 Protection of Environment... MARINE COMPRESSION-IGNITION ENGINES AND VESSELS Emission Standards and Related Requirements § 1042.101...

40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... information equivalent to such in-use data, such as data from research engines or similar engine models that... Category 1 engines and Category 2 engines. 1042.101 Section 1042.101 Protection of Environment... MARINE COMPRESSION-IGNITION ENGINES AND VESSELS Emission Standards and Related Requirements § 1042.101...

40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... information equivalent to such in-use data, such as data from research engines or similar engine models that... Category 1 engines and Category 2 engines. 1042.101 Section 1042.101 Protection of Environment... MARINE COMPRESSION-IGNITION ENGINES AND VESSELS Emission Standards and Related Requirements § 1042.101...

Dual-learning systems during speech category learning

PubMed Central

Chandrasekaran, Bharath; Yi, Han-Gyol; Maddox, W. Todd

2013-01-01

Dual-systems models of visual category learning posit the existence of an explicit, hypothesis-testing ‘reflective’ system, as well as an implicit, procedural-based ‘reflexive’ system. The reflective and reflexive learning systems are competitive and neurally dissociable. Relatively little is known about the role of these domain-general learning systems in speech category learning. Given the multidimensional, redundant, and variable nature of acoustic cues in speech categories, our working hypothesis is that speech categories are learned reflexively. To this end, we examined the relative contribution of these learning systems to speech learning in adults. Native English speakers learned to categorize Mandarin tone categories over 480 trials. The training protocol involved trial-by-trial feedback and multiple talkers. Experiment 1 and 2 examined the effect of manipulating the timing (immediate vs. delayed) and information content (full vs. minimal) of feedback. Dual-systems models of visual category learning predict that delayed feedback and providing rich, informational feedback enhance reflective learning, while immediate and minimally informative feedback enhance reflexive learning. Across the two experiments, our results show feedback manipulations that targeted reflexive learning enhanced category learning success. In Experiment 3, we examined the role of trial-to-trial talker information (mixed vs. blocked presentation) on speech category learning success. We hypothesized that the mixed condition would enhance reflexive learning by not allowing an association between talker-related acoustic cues and speech categories. Our results show that the mixed talker condition led to relatively greater accuracies. Our experiments demonstrate that speech categories are optimally learned by training methods that target the reflexive learning system. PMID:24002965

Investigation of the influence of textiles and surface treatments on blistering using a novel simulant.

PubMed

Guerra, C; Schwartz, C J

2012-02-01

Friction blisters occur when shear loading causes the separation of dermal layers. Consequences range from minor pain to life-threatening infection. Past research in blister formation has focused on in vivo experiments, which complicate a mechanics-based study of the phenomenon. A Synthetic Skin Simulant Platform (3SP) approach was developed to investigate the effect of textile fabrics (t-shirt knit and denim cottons) and surface treatments (dry and wet lubricants) on blister formation. 3SP samples consist of bonded elastomeric layers that are surrogates for various dermal layers. These layers display frictional and mechanical properties similar to their anatomical analogues. Blistering was assessed by the measurement of deboned area between layers. Denim caused greater blistering than did the t-shirt knit cotton, and both lubricants significantly reduced blister area and surface damage. A triglyceride-based lubricant had a more pronounced effect on blister reduction than corn starch. The triglyceride lubricant used with t-shirt knit cotton resulted in no blisters being formed. The performance of the 3SP approach follows previously reported frictional behavior of skin in vivo. The results of textile and surface treatment performance suggest that future 3SP iterations can be focused on specific anatomical sites based on application type. © 2011 John Wiley & Sons A/S.

Category Label Effects on Chinese Children's Inductive Inferences: Modulation by Perceptual Detail and Category Specificity

ERIC Educational Resources Information Center

Long, Changquan; Lu, Xiaoying; Zhang, Li; Li, Hong; Deak, Gedeon O.

2012-01-01

Inductive generalization of novel properties to same-category or similar-looking objects was studied in Chinese preschool children. The effects of category labels on generalizations were investigated by comparing basic-level labels, superordinate-level labels, and a control phrase applied to three kinds of stimulus materials: colored photographs…

40 CFR 156.62 - Toxicity Category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... being the highest toxicity category. Most human hazard, precautionary statements, and human personal protective equipment statements are based upon the Toxicity Category of the pesticide product as sold or...

40 CFR 156.62 - Toxicity Category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... being the highest toxicity category. Most human hazard, precautionary statements, and human personal protective equipment statements are based upon the Toxicity Category of the pesticide product as sold or...

Hippocampal activation during episodic and semantic memory retrieval: comparing category production and category cued recall.

PubMed

Ryan, Lee; Cox, Christine; Hayes, Scott M; Nadel, Lynn

2008-01-01

Whether or not the hippocampus participates in semantic memory retrieval has been the focus of much debate in the literature. However, few neuroimaging studies have directly compared hippocampal activation during semantic and episodic retrieval tasks that are well matched in all respects other than the source of the retrieved information. In Experiment 1, we compared hippocampal fMRI activation during a classic semantic memory task, category production, and an episodic version of the same task, category cued recall. Left hippocampal activation was observed in both episodic and semantic conditions, although other regions of the brain clearly distinguished the two tasks. Interestingly, participants reported using retrieval strategies during the semantic retrieval task that relied on autobiographical and spatial information; for example, visualizing themselves in their kitchen while producing items for the category kitchen utensils. In Experiment 2, we considered whether the use of these spatial and autobiographical retrieval strategies could have accounted for the hippocampal activation observed in Experiment 1. Categories were presented that elicited one of three retrieval strategy types, autobiographical and spatial, autobiographical and nonspatial, and neither autobiographical nor spatial. Once again, similar hippocampal activation was observed for all three category types, regardless of the inclusion of spatial or autobiographical content. We conclude that the distinction between semantic and episodic memory is more complex than classic memory models suggest.

Hippocampal Activation during Episodic and Semantic Memory Retrieval: Comparing Category Production and Category Cued Recall

PubMed Central

Ryan, Lee; Cox, Christine; Hayes, Scott M.; Nadel, Lynn

2008-01-01

Whether or not the hippocampus participates in semantic memory retrieval has been the focus of much debate in the literature. However, few neuroimaging studies have directly compared hippocampal activation during semantic and episodic retrieval tasks that are well matched in all respects other than the source of the retrieved information. In Experiment 1, we compared hippocampal fMRI activation during a classic semantic memory task, category production, and an episodic version of the same task, category cued recall. Left hippocampal activation was observed in both episodic and semantic conditions, although other regions of the brain clearly distinguished the two tasks. Interestingly, participants reported using retrieval strategies during the semantic retrieval task that relied on autobiographical and spatial information; for example, visualizing themselves in their kitchen while producing items for the category kitchen utensils. In Experiment 2, we considered whether the use of these spatial and autobiographical retrieval strategies could have accounted for the hippocampal activation observed in Experiment 1. Categories were presented that elicited one of three retrieval strategy types, autobiographical and spatial, autobiographical and nonspatial, and neither autobiographical nor spatial. Once again, similar hippocampal activation was observed for all three category types, regardless of the inclusion of spatial or autobiographical content. We conclude that the distinction between semantic and episodic memory is more complex than classic memory models suggest. PMID:18420234

Rapid Fabrication Techniques for Liquid Rocket Channel Wall Nozzles

NASA Technical Reports Server (NTRS)

Gradl, Paul R.

2016-01-01

The functions of a regeneratively-cooled nozzle are to (1) expand combustion gases to increase exhaust gas velocity while, (2) maintaining adequate wall temperatures to prevent structural failure, and (3) transfer heat from the hot gases to the coolant fluid to promote injector performance and stability. Regeneratively-cooled nozzles are grouped into two categories: tube-wall nozzles and channel wall nozzles. A channel wall nozzle is designed with an internal liner containing a series of integral coolant channels that are closed out with an external jacket. Manifolds are attached at each end of the nozzle to distribute coolant to and away from the channels. A variety of manufacturing techniques have been explored for channel wall nozzles, including state of the art laser-welded closeouts and pressure-assisted braze closeouts. This paper discusses techniques that NASA MSFC is evaluating for rapid fabrication of channel wall nozzles that address liner fabrication, slotting techniques and liner closeout techniques. Techniques being evaluated for liner fabrication include large-scale additive manufacturing of freeform-deposition structures to create the liner blanks. Abrasive water jet milling is being evaluated for cutting the complex coolant channel geometries. Techniques being considered for rapid closeout of the slotted liners include freeform deposition, explosive bonding and Cold Spray. Each of these techniques, development work and results are discussed in further detail in this paper.

Advanced stitching technology

NASA Technical Reports Server (NTRS)

Scardino, Frank L.

1992-01-01

In the design of textile composites, the selection of materials and constructional techniques must be matched with product performance, productivity, and cost requirements. Constructional techniques vary. A classification of various textile composite systems is given. In general, the chopped fiber system is not suitable for structural composite applications because of fiber discontinuity, uncontrolled fiber orientation and a lack of fiber integration or entanglement. Linear filament yarn systems are acceptable for structural components which are exposed to simple tension in their applications. To qualify for more general use as structural components, filament yarn systems must be multi-directionally positioned. With the most sophisticated filament winding and laying techniques, however, the Type 2 systems have limited potential for general load-bearing applications because of a lack of filament integration or entanglement, which means vulnerability to splitting and delamination among filament layers. The laminar systems (Type 3) represented by a variety of simple fabrics (woven, knitted, braided and nonwoven) are especially suitable for load-bearing panels in flat form and for beams in a roled up to wound form. The totally integrated, advanced fabric system (Type 4) are thought to be the most reliable for general load-bearing applications because of fiber continuity and because of controlled multiaxial fiber orientation and entanglement. Consequently, the risk of splitting and delamination is minimized and practically omitted. Type 4 systems can be woven, knitted, braided or stitched through with very special equipment. Multiaxial fabric technologies are discussed.

36 CFR 292.22 - Land category assignments.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the following four land categories: (i) Farm/forest/grazing land. (ii) Mining land. (iii) Residential.... Lands assigned to the Commercial, Residential, or Mining category may be reclassified as farm/forest... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Land category assignments...

36 CFR 292.22 - Land category assignments.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the following four land categories: (i) Farm/forest/grazing land. (ii) Mining land. (iii) Residential.... Lands assigned to the Commercial, Residential, or Mining category may be reclassified as farm/forest... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Land category assignments...

36 CFR 292.22 - Land category assignments.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the following four land categories: (i) Farm/forest/grazing land. (ii) Mining land. (iii) Residential.... Lands assigned to the Commercial, Residential, or Mining category may be reclassified as farm/forest... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Land category assignments...

36 CFR 292.22 - Land category assignments.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the following four land categories: (i) Farm/forest/grazing land. (ii) Mining land. (iii) Residential.... Lands assigned to the Commercial, Residential, or Mining category may be reclassified as farm/forest... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Land category assignments...

14 CFR 29.85 - Balked landing: Category A.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Balked landing: Category A. 29.85 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.85 Balked landing: Category A. For Category A rotorcraft, the balked landing path with the critical engine inoperative must be...

14 CFR 29.85 - Balked landing: Category A.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Balked landing: Category A. 29.85 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.85 Balked landing: Category A. For Category A rotorcraft, the balked landing path with the critical engine inoperative must be...

Supervised and Unsupervised Learning of Multidimensional Acoustic Categories

ERIC Educational Resources Information Center

Goudbeek, Martijn; Swingley, Daniel; Smits, Roel

2009-01-01

Learning to recognize the contrasts of a language-specific phonemic repertoire can be viewed as forming categories in a multidimensional psychophysical space. Research on the learning of distributionally defined visual categories has shown that categories defined over 1 dimension are easy to learn and that learning multidimensional categories is…

Eyetracking Reveals Multiple-Category Use in Induction

ERIC Educational Resources Information Center

Chen, Stephanie Y.; Ross, Brian H.; Murphy, Gregory L.

2016-01-01

Category information is used to predict properties of new category members. When categorization is uncertain, people often rely on only one, most likely category to make predictions. Yet studies of perception and action often conclude that people combine multiple sources of information near-optimally. We present a perception-action analog of…

Polymorphous computing fabric

DOEpatents

Wolinski, Christophe Czeslaw [Los Alamos, NM; Gokhale, Maya B [Los Alamos, NM; McCabe, Kevin Peter [Los Alamos, NM

2011-01-18

Fabric-based computing systems and methods are disclosed. A fabric-based computing system can include a polymorphous computing fabric that can be customized on a per application basis and a host processor in communication with said polymorphous computing fabric. The polymorphous computing fabric includes a cellular architecture that can be highly parameterized to enable a customized synthesis of fabric instances for a variety of enhanced application performances thereof. A global memory concept can also be included that provides the host processor random access to all variables and instructions associated with the polymorphous computing fabric.

Category-based predictions: influence of uncertainty and feature associations.

PubMed

Ross, B H; Murphy, G L

1996-05-01

Four experiments examined how people make inductive inferences using categories. Subjects read stories in which 2 categories were mentioned as possible identities of an object. The less likely category was varied to determine if people were using it, as well as the most likely category, in making predictions about the object. Experiment 1 showed that even when categorization uncertainty was emphasized, subjects used only 1 category as the basis for their prediction. Experiments 2-4 examined whether people would use multiple categories for making predictions when the feature to be predicted was associated to the less likely category. Multiple categories were used in this case, but only in limited circumstances; furthermore, using multiple categories in 1 prediction did not cause subjects to use them for subsequent predictions. The results increase the understanding of how categories are used in inductive inference.

29 CFR 4044.14 - Priority category 4 benefits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... priority category 4 with respect to a participant is not limited by the aggregate benefits limitations set... 29 Labor 9 2010-07-01 2010-07-01 false Priority category 4 benefits. 4044.14 Section 4044.14 Labor... Priority category 4 benefits. The benefits assigned to priority category 4 with respect to each participant...

14 CFR 29.83 - Landing: Category B.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Landing: Category B. 29.83 Section 29.83... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.83 Landing: Category B. (a) For each... of approximately 3 knots for water landings) from a point 50 feet above the landing surface must be...

Incremental Bayesian Category Learning from Natural Language

ERIC Educational Resources Information Center

Frermann, Lea; Lapata, Mirella

2016-01-01

Models of category learning have been extensively studied in cognitive science and primarily tested on perceptual abstractions or artificial stimuli. In this paper, we focus on categories acquired from natural language stimuli, that is, words (e.g., "chair" is a member of the furniture category). We present a Bayesian model that, unlike…

Identification of prelinguistic phonological categories.

PubMed

Ramsdell, Heather L; Oller, D Kimbrough; Buder, Eugene H; Ethington, Corinna A; Chorna, Lesya

2012-12-01

The prelinguistic infant's babbling repertoire of syllables--the phonological categories that form the basis for early word learning--is noticed by caregivers who interact with infants around them. Prior research on babbling has not explored the caregiver's role in recognition of early vocal categories as foundations for word learning. In the present work, the authors begin to address this gap. The authors explored vocalizations produced by 8 infants at 3 ages (8, 10, and 12 months) in studies illustrating identification of phonological categories through caregiver report, laboratory procedures simulating the caregiver's natural mode of listening, and the more traditional laboratory approach (phonetic transcription). Caregivers reported small repertoires of syllables for their infants. Repertoires of similar size and phonetic content were discerned in the laboratory by judges who simulated the caregiver's natural mode of listening. However, phonetic transcription with repeated listening to infant recordings yielded repertoire sizes that vastly exceeded those reported by caregivers and naturalistic listeners. The results suggest that caregiver report and naturalistic listening by laboratory staff can provide a new way to explore key characteristics of early infant vocal categories, a way that may provide insight into later speech and language development.

75 FR 40756 - Implementation Guidance for Physical Protection of Byproduct Material; Category 1 and Category 2...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-14

...-2010-0194] RIN 3150-AI12 Implementation Guidance for Physical Protection of Byproduct Material... licensee or applicant for implementation of proposed 10 CFR part 37, ``Physical Protection of Byproduct... ``Implementation Guidance for 10 CFR part 37 Physical Protection of Byproduct Material, Category 1 and Category 2...

SUSTAIN: a network model of category learning.

PubMed

Love, Bradley C; Medin, Douglas L; Gureckis, Todd M

2004-04-01

SUSTAIN (Supervised and Unsupervised STratified Adaptive Incremental Network) is a model of how humans learn categories from examples. SUSTAIN initially assumes a simple category structure. If simple solutions prove inadequate and SUSTAIN is confronted with a surprising event (e.g., it is told that a bat is a mammal instead of a bird), SUSTAIN recruits an additional cluster to represent the surprising event. Newly recruited clusters are available to explain future events and can themselves evolve into prototypes-attractors-rules. SUSTAIN's discovery of category substructure is affected not only by the structure of the world but by the nature of the learning task and the learner's goals. SUSTAIN successfully extends category learning models to studies of inference learning, unsupervised learning, category construction, and contexts in which identification learning is faster than classification learning.

NASA Scope and Subject Category Guide

NASA Technical Reports Server (NTRS)

2011-01-01

This guide provides a simple, effective tool to assist aerospace information analysts and database builders in the high-level subject classification of technical materials. Each of the 76 subject categories comprising the classification scheme is presented with a description of category scope, a listing of subtopics, cross references, and an indication of particular areas of NASA interest. The guide also includes an index of nearly 3,000 specific research topics cross referenced to the subject categories. The portable document format (PDF) version of the guide contains links in the index from each input subject to its corresponding categories. In addition to subject classification, the guide can serve as an aid to searching databases that use the classification scheme, and is also an excellent selection guide for those involved in the acquisition of aerospace literature. The CD-ROM contains both HTML and PDF versions.

Influence of Emotionally Charged Information on Category-Based Induction

PubMed Central

Zhu, Jennifer; Murphy, Gregory L.

2013-01-01

Categories help us make predictions, or inductions, about new objects. However, we cannot always be certain that a novel object belongs to the category we are using to make predictions. In such cases, people should use multiple categories to make inductions. Past research finds that people often use only the most likely category to make inductions, even if it is not certain. In two experiments, subjects read stories and answered questions about items whose categorization was uncertain. In Experiment 1, the less likely category was either emotionally neutral or dangerous (emotionally charged or likely to pose a threat). Subjects used multiple categories in induction when one of the categories was dangerous but not when they were all neutral. In Experiment 2, the most likely category was dangerous. Here, people used multiple categories, but there was also an effect of avoidance, in which people denied that dangerous categories were the most likely. The attention-grabbing power of dangerous categories may be balanced by a higher-level strategy to reject them. PMID:23372700

An Analysis of Category Management of Service Contracts

DTIC Science & Technology

2017-12-01

management teams a way to make informed , data-driven decisions. Data-driven decisions derived from clustering not only align with Category...savings. Furthermore, this methodology provides a data-driven visualization to inform sound business decisions on potential Category Management ...Category Management initiatives. The Maptitude software will allow future research to collect data and develop visualizations to inform Category

Aversive Learning Modulates Cortical Representations of Object Categories

PubMed Central

Dunsmoor, Joseph E.; Kragel, Philip A.; Martin, Alex; LaBar, Kevin S.

2014-01-01

Experimental studies of conditioned learning reveal activity changes in the amygdala and unimodal sensory cortex underlying fear acquisition to simple stimuli. However, real-world fears typically involve complex stimuli represented at the category level. A consequence of category-level representations of threat is that aversive experiences with particular category members may lead one to infer that related exemplars likewise pose a threat, despite variations in physical form. Here, we examined the effect of category-level representations of threat on human brain activation using 2 superordinate categories (animals and tools) as conditioned stimuli. Hemodynamic activity in the amygdala and category-selective cortex was modulated by the reinforcement contingency, leading to widespread fear of different exemplars from the reinforced category. Multivariate representational similarity analyses revealed that activity patterns in the amygdala and object-selective cortex were more similar among exemplars from the threat versus safe category. Learning to fear animate objects was additionally characterized by enhanced functional coupling between the amygdala and fusiform gyrus. Finally, hippocampal activity co-varied with object typicality and amygdala activation early during training. These findings provide novel evidence that aversive learning can modulate category-level representations of object concepts, thereby enabling individuals to express fear to a range of related stimuli. PMID:23709642

On Monoids in the Category of Sets and Relations

NASA Astrophysics Data System (ADS)

Jenčová, Anna; Jenča, Gejza

2017-12-01

The category R e l is the category of sets (objects) and relations (morphisms). Equipped with the direct product of sets, R e l is a monoidal category. Moreover, R e l is a locally posetal 2-category, since every homset R e l( A, B) is a poset with respect to inclusion. We examine the 2-category of monoids R e l M o n in this category. The morphism we use are lax. This category includes, as subcategories, various interesting classes: hypergroups, partial monoids (which include various types of quantum logics, for example effect algebras) and small categories. We show how the 2-categorical structure gives rise to several previously defined notions in these categories, for example certain types of congruence relations on generalized effect algebras. This explains where these definitions come from.

Categories for Names or Names of Categories? The Interplay Between Domain-Specific Conceptual Structure and Language.

ERIC Educational Resources Information Center

Diesendruck, Gil

2003-01-01

Drawing on the notion of the domain-specificity of recognition, reviews evidence on the effect of language in classification of and reasoning about categories from different domains. Looks at anthropological infant classification, and preschool categorization literature. Suggests the causal nature and indicative power of animal categories seem to…

Diagnostic Categories in Autobiographical Accounts of Illness.

PubMed

Kelly, Michael P

2015-01-01

Working within frameworks drawn from the writings of Immanuel Kant, Alfred Schutz, and Kenneth Burke, this article examines the role that diagnostic categories play in autobiographical accounts of illness, with a special focus on chronic disease. Four lay diagnostic categories, each with different connections to formal medical diagnostic categories, serve as typifications to make sense of the way the lifeworld changes over the course of chronic illness. These diagnostic categories are used in conjunction with another set of typifications: lay epidemiologies, lay etiologies, lay prognostics, and lay therapeutics. Together these serve to construct and reconstruct the self at the center of the lifeworld. Embedded within the lay diagnostic categories are narratives of progression, regression, or stability, forms of typification derived from literary and storytelling genres. These narratives are developed by the self in autobiographical accounts of illness.

Ad hoc categories and false memories: Memory illusions for categories created on-the-spot.

PubMed

Soro, Jerônimo C; Ferreira, Mário B; Semin, Gün R; Mata, André; Carneiro, Paula

2017-11-01

Three experiments were designed to test whether experimentally created ad hoc associative networks evoke false memories. We used the DRM (Deese, Roediger, McDermott) paradigm with lists of ad hoc categories composed of exemplars aggregated toward specific goals (e.g., going for a picnic) that do not share any consistent set of features. Experiment 1 revealed considerable levels of false recognitions of critical words from ad hoc categories. False recognitions occurred even when the lists were presented without an organizing theme (i.e., the category's label). Experiments 1 and 2 tested whether (a) the ease of identifying the categories' themes, and (b) the lists' backward associative strength could be driving the effect. List identifiability did not correlate with false recognition, and the effect remained even when backward associative strength was controlled for. Experiment 3 manipulated the distractor items in the recognition task to address the hypothesis that the salience of unrelated items could be facilitating the occurrence of the phenomenon. The effect remained when controlling for this source of facilitation. These results have implications for assumptions made by theories of false memories, namely the preexistence of associations in the activation-monitoring framework and the central role of gist extraction in fuzzy-trace theory, while providing evidence of the occurrence of false memories for more dynamic and context-dependent knowledge structures. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

On the classification of weakly integral modular categories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruillard, Paul; Galindo, César; Ng, Siu-Hung

In this paper we classify all modular categories of dimension 4m, where m is an odd square-free integer, and all rank 6 and rank 7 weakly integral modular categories. This completes the classification of weakly integral modular categories through rank 7. In particular, our results imply that all integral modular categories of rank at most 7 are pointed (that is, every simple object has dimension 1). All the non-integral (but weakly integral) modular categories of ranks 6 and 7 have dimension 4m, with m an odd square free integer, so their classification is an application of our main result. Themore » classification of rank 7 integral modular categories is facilitated by an analysis of the two group actions on modular categories: the Galois group of the field generated by the entries of the S-matrix and the group of invertible isomorphism classes of objects. We derive some valuable arithmetic consequences from these actions.« less

Contextual memory and skill transfer in category search.

PubMed

Kole, James A; Healy, Alice F; Fierman, Deanna M; Bourne, Lyle E

2010-01-01

In three experiments, we examined transfer and contextual memory in a category search task. Each experiment included two phases (training and test), during which participants searched through category and exemplar menus for targets. In Experiment 1, the targets were from one of two domains during training (grocery store or department store); the domain was either the same or changed at test. Also, the categories were organized in one of two ways (alphabetically or semantically); the organization either remained the same or changed at test. In Experiments 2 and 3, domain and organization were held constant; however, categories or exemplars were the same, partially replaced, or entirely replaced across phases in order to simulate the dynamic nature of category search in everyday situations. Transfer occurred at test when the category organization or domain was maintained and when the categories or exemplars matched (partially or entirely) those at training. These results demonstrate that transfer is facilitated by overlap in training and testing contexts.

The Potential of Improving Medical Textile for Cutaneous Diseases

NASA Astrophysics Data System (ADS)

Radu, C. D.; Cerempei, A.; Salariu, M.; Parteni, O.; Ulea, E.; Campagne, Chr

2017-10-01

The paper dwells on the prospect of medical textiles designed to release a drug/active principle to the dermis of patients suffering from cutaneous disease (allergic dermatitis, psoriasis, bacterial/infectious conditions and inflammatory conditions). The paper is an overview of general and experimental data from textile applications. An adequate medical textile may have a cellulosic structure, mainly knitted cotton fabric. In special cases, one may use woven fabric for multilayer drug-releasing systems. As far as controlled release systems are concerned, we carried out a critical comparison between the systems described in literature and our experimental findings as concerns cyclodextrin, hydrogel, film charged with active principles and multilayer system.

Thermal comfort of aeroplane seats: influence of different seat materials and the use of laboratory test methods.

PubMed

Bartels, Volkmar T

2003-07-01

This study determined the influence of different cover and cushion materials on the thermal comfort of aeroplane seats. Different materials as well as ready made seats were investigated by the physiological laboratory test methods Skin Model and seat comfort tester. Additionally, seat trials with human test subjects were performed in a climatic chamber. Results show that a fabric cover produces a considerably higher sweat transport than leather. A three-dimensional knitted spacer fabric turns out to be the better cushion alternative in comparison to a moulded foam pad. Results from the physiological laboratory test methods nicely correspond to the seat trials with human test subjects.

Classification versus inference learning contrasted with real-world categories.

PubMed

Jones, Erin L; Ross, Brian H

2011-07-01

Categories are learned and used in a variety of ways, but the research focus has been on classification learning. Recent work contrasting classification with inference learning of categories found important later differences in category performance. However, theoretical accounts differ on whether this is due to an inherent difference between the tasks or to the implementation decisions. The inherent-difference explanation argues that inference learners focus on the internal structure of the categories--what each category is like--while classification learners focus on diagnostic information to predict category membership. In two experiments, using real-world categories and controlling for earlier methodological differences, inference learners learned more about what each category was like than did classification learners, as evidenced by higher performance on a novel classification test. These results suggest that there is an inherent difference between learning new categories by classifying an item versus inferring a feature.

Category mistakes: A barrier to effective environmental management.

PubMed

Wallace, Ken J; Jago, Mark

2017-09-01

How entities, the things that exist, are defined and categorised affects all aspects of environmental management including technical descriptions, quantitative analyses, participatory processes, planning, and decisions. Consequently, ambiguous definitions and wrongly assigning entities to categories, referred to as category mistakes, are barriers to effective management. Confusion caused by treating the term 'biodiversity' variously as the property of an area, the biota of an area, and a preferred end state (a value) - quite different categories of entities - is one example. To overcome such difficulties, we develop and define four entity categories - elements, processes, properties, and values - and two derived categories - states and systems. We argue that adoption of these categories and definitions will significantly improve environmental communication and analysis, and thus strengthen planning and decision-making. Copyright © 2017 Elsevier Ltd. All rights reserved.

Behavior-based aggregation of land categories for temporal change analysis

NASA Astrophysics Data System (ADS)

Aldwaik, Safaa Zakaria; Onsted, Jeffrey A.; Pontius, Robert Gilmore, Jr.

2015-03-01

Comparison between two time points of the same categorical variable for the same study extent can reveal changes among categories over time, such as transitions among land categories. If many categories exist, then analysis can be difficult to interpret. Category aggregation is the procedure that combines two or more categories to create a single broader category. Aggregation can simplify interpretation, and can also influence the sizes and types of changes. Some classifications have an a priori hierarchy to facilitate aggregation, but an a priori aggregation might make researchers blind to important category dynamics. We created an algorithm to aggregate categories in a sequence of steps based on the categories' behaviors in terms of gross losses and gross gains. The behavior-based algorithm aggregates net gaining categories with net gaining categories and aggregates net losing categories with net losing categories, but never aggregates a net gaining category with a net losing category. The behavior-based algorithm at each step in the sequence maintains net change and maximizes swap change. We present a case study where data from 2001 and 2006 for 64 land categories indicate change on 17% of the study extent. The behavior-based algorithm produces a set of 10 categories that maintains nearly the original amount of change. In contrast, an a priori aggregation produces 10 categories while reducing the change to 9%. We offer a free computer program to perform the behavior-based aggregation.

Psychopathic disorder: a category mistake?

PubMed Central

Holmes, C A

1991-01-01

Although the concept of psychopathy retains its currency in British psychiatry, apparently being meaningful as well as useful to practitioners (1), it is often taken to refer to a purely legal category with social control functions rather than a medical diagnosis with treatment implications. I wish, in this brief article, to suggest that it is essentially, and most usefully, an ethical category which stands outside the diagnostic framework of present-day psychiatry. PMID:1870086

Category-contingent face adaptation for novel colour categories: Contingent effects are seen only after social or meaningful labelling.

PubMed

Little, Anthony C; DeBruine, Lisa M; Jones, Benedict C

2011-01-01

A face appears normal when it approximates the average of a population. Consequently, exposure to faces biases perceptions of subsequently viewed faces such that faces similar to those recently seen are perceived as more normal. Simultaneously inducing such aftereffects in opposite directions for two groups of faces indicates somewhat discrete representations for those groups. Here we examine how labelling influences the perception of category in faces differing in colour. We show category-contingent aftereffects following exposure to faces differing in eye spacing (wide versus narrow) for blue versus red faces when such groups are consistently labelled with socially meaningful labels (Extravert versus Introvert; Soldier versus Builder). Category-contingent aftereffects were not seen using identical methodology when labels were not meaningful or were absent. These data suggest that human representations of faces can be rapidly tuned to code for meaningful social categories and that such tuning requires both a label and an associated visual difference. Results highlight the flexibility of the cognitive visual system to discriminate categories even in adulthood. Copyright © 2010 Elsevier B.V. All rights reserved.

Observation versus classification in supervised category learning.

PubMed

Levering, Kimery R; Kurtz, Kenneth J

2015-02-01

The traditional supervised classification paradigm encourages learners to acquire only the knowledge needed to predict category membership (a discriminative approach). An alternative that aligns with important aspects of real-world concept formation is learning with a broader focus to acquire knowledge of the internal structure of each category (a generative approach). Our work addresses the impact of a particular component of the traditional classification task: the guess-and-correct cycle. We compare classification learning to a supervised observational learning task in which learners are shown labeled examples but make no classification response. The goals of this work sit at two levels: (1) testing for differences in the nature of the category representations that arise from two basic learning modes; and (2) evaluating the generative/discriminative continuum as a theoretical tool for understand learning modes and their outcomes. Specifically, we view the guess-and-correct cycle as consistent with a more discriminative approach and therefore expected it to lead to narrower category knowledge. Across two experiments, the observational mode led to greater sensitivity to distributional properties of features and correlations between features. We conclude that a relatively subtle procedural difference in supervised category learning substantially impacts what learners come to know about the categories. The results demonstrate the value of the generative/discriminative continuum as a tool for advancing the psychology of category learning and also provide a valuable constraint for formal models and associated theories.

Social categories as markers of intrinsic interpersonal obligations.

PubMed

Rhodes, Marjorie; Chalik, Lisa

2013-06-01

Social categorization is an early-developing feature of human social cognition, yet the role that social categories play in children's understanding of and predictions about human behavior has been unclear. In the studies reported here, we tested whether a foundational functional role of social categories is to mark people as intrinsically obligated to one another (e.g., obligated to protect rather than harm). In three studies, children (aged 3-9, N = 124) viewed only within-category harm as violating intrinsic obligations; in contrast, they viewed between-category harm as violating extrinsic obligations defined by explicit rules. These data indicate that children view social categories as marking patterns of intrinsic interpersonal obligations, suggesting that a key function of social categories is to support inferences about how people will relate to members of their own and other groups.

Conceptual Influences on Category-Based Induction

ERIC Educational Resources Information Center

Gelman, Susan A.; Davidson, Natalie S.

2013-01-01

One important function of categories is to permit rich inductive inferences. Prior work shows that children use category labels to guide their inductive inferences. However, there are competing theories to explain this phenomenon, differing in the roles attributed to conceptual information vs. perceptual similarity. Seven experiments with 4- to…

Category-Specificity in Visual Object Recognition

ERIC Educational Resources Information Center

Gerlach, Christian

2009-01-01

Are all categories of objects recognized in the same manner visually? Evidence from neuropsychology suggests they are not: some brain damaged patients are more impaired in recognizing natural objects than artefacts whereas others show the opposite impairment. Category-effects have also been demonstrated in neurologically intact subjects, but the…

33 CFR 151.35 - Certificates needed to carry Category D NLS and Category D Oil-like NLS.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Protocol on Environmental Protection to the Antarctic Treaty as it Pertains to Pollution from Ships Noxious Liquid Substance Pollution § 151.35 Certificates needed to carry Category D NLS and Category D Oil-like... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION VESSELS CARRYING OIL, NOXIOUS LIQUID...

Fabrication of superhydrophobic cotton fabrics using crosslinking polymerization method

NASA Astrophysics Data System (ADS)

Jiang, Bin; Chen, Zhenxing; Sun, Yongli; Yang, Huawei; Zhang, Hongjie; Dou, Haozhen; Zhang, Luhong

2018-05-01

With the aim of removing and recycling oil and organic solvent from water, a facile and low-cost crosslinking polymerization method was first applied on surface modification of cotton fabrics for water/oil separation. Micro-nano hierarchical rough structure was constructed by triethylenetetramine (TETA) and trimesoyl chloride (TMC) that formed a polymeric layer on the surface of the fabric and anchored Al2O3 nanoparticles firmly between the fabric surface and the polymer layer. Superhydrophobic property was further obtained through self-assembly grafting of hydrophobic groups on the rough surface. The as-prepared cotton fabric exhibited superoleophilicity in atmosphere and superhydrophobicity both in atmosphere and under oil with the water contact angle of 153° and 152° respectively. Water/oil separation test showed that the as-prepared cotton fabric can handle with various oil-water mixtures with a high separation efficiency over 99%. More importantly, the separation efficiency remained above 98% over 20 cycles of reusing without losing its superhydrophobicity which demonstrated excellent reusability in oil/water separation process. Moreover, the as-prepared cotton fabric possessed good contamination resistance ability and self-cleaning property. Simulation washing process test showed the superhydrophobic cotton fabric maintained high value of water contact angle above 150° after 100 times washing, indicating great stability and durability. In summary, this work provides a brand-new way to surface modification of cotton fabric and makes it a promising candidate material for oil/water separation.

Learning, retention, and generalization of haptic categories

NASA Astrophysics Data System (ADS)

Do, Phuong T.

This dissertation explored how haptic concepts are learned, retained, and generalized to the same or different modality. Participants learned to classify objects into three categories either visually or haptically via different training procedures, followed by an immediate or delayed transfer test. Experiment I involved visual versus haptic learning and transfer. Intermodal matching between vision and haptics was investigated in Experiment II. Experiments III and IV examined intersensory conflict in within- and between-category bimodal situations to determine the degree of perceptual dominance between sight and touch. Experiment V explored the intramodal relationship between similarity and categorization in a psychological space, as revealed by MDS analysis of similarity judgments. Major findings were: (1) visual examination resulted in relatively higher performance accuracy than haptic learning; (2) systematic training produced better category learning of haptic concepts across all modality conditions; (3) the category prototypes were rated newer than any transfer stimulus followed learning both immediately and after a week delay; and, (4) although they converged at the apex of two transformational trajectories, the category prototypes became more central to their respective categories and increasingly structured as a function of learning. Implications for theories of multimodal similarity and categorization behavior are discussed in terms of discrimination learning, sensory integration, and dominance relation.

46 CFR 120.352 - Battery categories.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Battery categories. 120.352 Section 120.352 Shipping... and Distribution Systems § 120.352 Battery categories. This section applies to batteries installed to... sources of power to final emergency loads. (a) Large. A large battery installation is one connected to a...

46 CFR 183.352 - Battery categories.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Battery categories. 183.352 Section 183.352 Shipping...) ELECTRICAL INSTALLATION Power Sources and Distribution Systems § 183.352 Battery categories. This section applies to batteries installed to meet the requirements of § 183.310 for secondary sources of power to...

7 CFR 993.503 - Size category.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Size category. 993.503 Section 993.503 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... categories listed in § 993.515 and fixes the range or the limits of the various size counts. Effective Date...

46 CFR 120.352 - Battery categories.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Battery categories. 120.352 Section 120.352 Shipping... and Distribution Systems § 120.352 Battery categories. This section applies to batteries installed to... sources of power to final emergency loads. (a) Large. A large battery installation is one connected to a...

46 CFR 183.352 - Battery categories.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Battery categories. 183.352 Section 183.352 Shipping...) ELECTRICAL INSTALLATION Power Sources and Distribution Systems § 183.352 Battery categories. This section applies to batteries installed to meet the requirements of § 183.310 for secondary sources of power to...

46 CFR 120.352 - Battery categories.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Battery categories. 120.352 Section 120.352 Shipping... and Distribution Systems § 120.352 Battery categories. This section applies to batteries installed to... sources of power to final emergency loads. (a) Large. A large battery installation is one connected to a...

46 CFR 120.352 - Battery categories.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Battery categories. 120.352 Section 120.352 Shipping... and Distribution Systems § 120.352 Battery categories. This section applies to batteries installed to... sources of power to final emergency loads. (a) Large. A large battery installation is one connected to a...

46 CFR 183.352 - Battery categories.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Battery categories. 183.352 Section 183.352 Shipping...) ELECTRICAL INSTALLATION Power Sources and Distribution Systems § 183.352 Battery categories. This section applies to batteries installed to meet the requirements of § 183.310 for secondary sources of power to...

46 CFR 120.352 - Battery categories.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Battery categories. 120.352 Section 120.352 Shipping... and Distribution Systems § 120.352 Battery categories. This section applies to batteries installed to... sources of power to final emergency loads. (a) Large. A large battery installation is one connected to a...

46 CFR 183.352 - Battery categories.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Battery categories. 183.352 Section 183.352 Shipping...) ELECTRICAL INSTALLATION Power Sources and Distribution Systems § 183.352 Battery categories. This section applies to batteries installed to meet the requirements of § 183.310 for secondary sources of power to...

46 CFR 183.352 - Battery categories.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Battery categories. 183.352 Section 183.352 Shipping...) ELECTRICAL INSTALLATION Power Sources and Distribution Systems § 183.352 Battery categories. This section applies to batteries installed to meet the requirements of § 183.310 for secondary sources of power to...

Stress adapted embroidered meshes with a graded pattern design for abdominal wall hernia repair

NASA Astrophysics Data System (ADS)

Hahn, J.; Bittrich, L.; Breier, A.; Spickenheuer, A.

2017-10-01

Abdominal wall hernias are one of the most relevant injuries of the digestive system with 25 million patients in 2013. Surgery is recommended primarily using allogenic non-absorbable wrap-knitted meshes. These meshes have in common that their stress-strain behaviour is not adapted to the anisotropic behaviour of native abdominal wall tissue. The ideal mesh should possess an adequate mechanical behaviour and a suitable porosity at the same time. An alternative fabrication method to wrap-knitting is the embroidery technology with a high flexibility in pattern design and adaption of mechanical properties. In this study, a pattern generator was created for pattern designs consisting of a base and a reinforcement pattern. The embroidered mesh structures demonstrated different structural and mechanical characteristics. Additionally, the investigation of the mechanical properties exhibited an anisotropic mechanical behaviour for the embroidered meshes. As a result, the investigated pattern generator and the embroidery technology allow the production of stress adapted mesh structures that are a promising approach for hernia reconstruction.

46 CFR 129.353 - Battery categories.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Battery categories. 129.353 Section 129.353 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.353 Battery categories. This section applies to batteries installed to meet the requirements of § 129.310(a) for secondary sources of power to vital loads...

46 CFR 129.353 - Battery categories.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Battery categories. 129.353 Section 129.353 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.353 Battery categories. This section applies to batteries installed to meet the requirements of § 129.310(a) for secondary sources of power to vital loads...

46 CFR 129.353 - Battery categories.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Battery categories. 129.353 Section 129.353 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.353 Battery categories. This section applies to batteries installed to meet the requirements of § 129.310(a) for secondary sources of power to vital loads...

46 CFR 129.353 - Battery categories.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Battery categories. 129.353 Section 129.353 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.353 Battery categories. This section applies to batteries installed to meet the requirements of § 129.310(a) for secondary sources of power to vital loads...

46 CFR 129.353 - Battery categories.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Battery categories. 129.353 Section 129.353 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.353 Battery categories. This section applies to batteries installed to meet the requirements of § 129.310(a) for secondary sources of power to vital loads...

The Role of Grammatical Category Information in Spoken Word Retrieval

PubMed Central

Duràn, Carolina Palma; Pillon, Agnesa

2011-01-01

We investigated the role of lexical syntactic information such as grammatical gender and category in spoken word retrieval processes by using a blocking paradigm in picture and written word naming experiments. In Experiments 1, 3, and 4, we found that the naming of target words (nouns) from pictures or written words was faster when these target words were named within a list where only words from the same grammatical category had to be produced (homogeneous category list: all nouns) than when they had to be produced within a list comprising also words from another grammatical category (heterogeneous category list: nouns and verbs). On the other hand, we detected no significant facilitation effect when the target words had to be named within a homogeneous gender list (all masculine nouns) compared to a heterogeneous gender list (both masculine and feminine nouns). In Experiment 2, using the same blocking paradigm by manipulating the semantic category of the items, we found that naming latencies were significantly slower in the semantic category homogeneous in comparison with the semantic category heterogeneous condition. Thus semantic category homogeneity caused an interference, not a facilitation effect like grammatical category homogeneity. Finally, in Experiment 5, nouns in the heterogeneous category condition had to be named just after a verb (category-switching position) or a noun (same-category position). We found a facilitation effect of category homogeneity but no significant effect of position, which showed that the effect of category homogeneity found in Experiments 1, 3, and 4 was not due to a cost of switching between grammatical categories in the heterogeneous grammatical category list. These findings supported the hypothesis that grammatical category information impacts word retrieval processes in speech production, even when words are to be produced in isolation. They are discussed within the context of extant theories of lexical production. PMID

The role of grammatical category information in spoken word retrieval.

PubMed

Duràn, Carolina Palma; Pillon, Agnesa

2011-01-01

We investigated the role of lexical syntactic information such as grammatical gender and category in spoken word retrieval processes by using a blocking paradigm in picture and written word naming experiments. In Experiments 1, 3, and 4, we found that the naming of target words (nouns) from pictures or written words was faster when these target words were named within a list where only words from the same grammatical category had to be produced (homogeneous category list: all nouns) than when they had to be produced within a list comprising also words from another grammatical category (heterogeneous category list: nouns and verbs). On the other hand, we detected no significant facilitation effect when the target words had to be named within a homogeneous gender list (all masculine nouns) compared to a heterogeneous gender list (both masculine and feminine nouns). In Experiment 2, using the same blocking paradigm by manipulating the semantic category of the items, we found that naming latencies were significantly slower in the semantic category homogeneous in comparison with the semantic category heterogeneous condition. Thus semantic category homogeneity caused an interference, not a facilitation effect like grammatical category homogeneity. Finally, in Experiment 5, nouns in the heterogeneous category condition had to be named just after a verb (category-switching position) or a noun (same-category position). We found a facilitation effect of category homogeneity but no significant effect of position, which showed that the effect of category homogeneity found in Experiments 1, 3, and 4 was not due to a cost of switching between grammatical categories in the heterogeneous grammatical category list. These findings supported the hypothesis that grammatical category information impacts word retrieval processes in speech production, even when words are to be produced in isolation. They are discussed within the context of extant theories of lexical production.

Infinite Index Subfactors and the GICAR Categories

NASA Astrophysics Data System (ADS)

Jones, Vaughan F. R.; Penneys, David

2015-10-01

Given a II1-subfactor of arbitrary index, we show that the rectangular GICAR category, also called the rectangular planar rook category, faithfully embeds as A - A bimodule maps among the bimodules . As a corollary, we get a lower bound on the dimension of the centralizer algebras for infinite index subfactors, and we also get that is nonabelian for , where is the Jones tower for . We also show that the annular GICAR/planar rook category acts as maps amongst the A-central vectors in , although this action may be degenerate. We prove these results in more generality using bimodules. The embedding of the GICAR category builds on work of Connes and Evans, who originally found GICAR algebras inside Temperley-Lieb algebras with finite modulus.

Geometric Representation of Association between Categories

ERIC Educational Resources Information Center

Heiser, Willem J.

2004-01-01

Categories can be counted, rated, or ranked, but they cannot be measured. Likewise, persons or individuals can be counted, rated, or ranked, but they cannot be measured either. Nevertheless, psychology has realized early on that it can take an indirect road to measurement: What can be measured is the strength of association between categories in…

An investigation of time course of category and semantic priming.

PubMed

Ray, Suchismita

2008-04-01

Low semantically similar exemplars in a category demonstrate the category-priming effect through priming of the category (i.e., exemplar-category-exemplar), whereas high semantically similar exemplars in the same category demonstrate the semantic-priming effect (i.e., direct activation of one high semantically similar exemplar by another). The author asked whether the category- and semantic-priming effects are based on a common memory process. She examined this question by testing the time courses of category- and semantic-priming effects. She tested participants on either category- or semantic-priming paradigm at 2 different time intervals (6 min and 42 min) by using a lexical decision task using exemplars from categories. Results showed that the time course of category priming was different from that of semantic priming. The author concludes that these 2 priming effects are based on 2 separate memory processes.

Effect of fibroin sponge coating on in vivo performance of knitted silk small diameter vascular grafts

PubMed Central

Fukayama, Toshiharu; Ozai, Yusuke; Shimokawadoko, Haruka; Aytemiz, Derya; Tanaka, Ryou; Machida, Noboru; Asakura, Tetsuo

2015-01-01

ABSTRACT Vascular grafts under 5 mm or less in diameter are not developed due to a problem caused by early thrombus formation, neointimal hyperplasia, etc. Bombyx mori silk fibroin (SF) which has biodegradability and tissue infiltration is focused as tube and coating material of vascular grafts. Coating is an important factor to maintain the strength of the anastomotic region of vascular grafts, and to prevent the blood leak from the vascular grafts after implantation. Therefore, in this research, we focused on the SF concentration of the coating solution, and tissue infiltration and remodeling were compared among each SF concentration. Silk poly (-ethylene) glycol diglycidyl ether (PGDE) coating with concentrations of 1.0%, 2.5%, 5.0%, and 7.5% SF were applied for the double-raschel knitted small-sized vessel with 1.5 mm diameter and 1cm in length. The grafts were implanted in the rat abdominal aorta and removed after 3 weeks or 3 months. Vascular grafts patency was monitored by ultrasound, and morphological evaluation was performed by histopathological examination. SF concentration had no significant effects on the patency rate. However, tissue infiltration was significantly higher in the sample of 2.5% SF in 3 weeks, and 1.0% and 2.5% SF in 3 months. Also, in comparison of length inside of the graft, stenosis were not found in 3 weeks, however, found with 5.0% and 7.5% in 3 months. From these results, it is clear that 2.5% SF coating is the most suitable concentration, based on the characteristics of less stenosis, early tissue infiltration, and less neointimal hyperplasia. PMID:26496652

The Conceptual Grouping Effect: Categories Matter (and Named Categories Matter More)

ERIC Educational Resources Information Center

Lupyan, Gary

2008-01-01

Do conceptual categories affect basic visual processing? A conceptual grouping effect for familiar stimuli is reported using a visual search paradigm. Search through conceptually-homogeneous non-targets was faster and more efficient than search through conceptually-heterogeneous non-targets. This effect cannot be attributed to perceptual factors…

Color categories affect pre-attentive color perception.

PubMed

Clifford, Alexandra; Holmes, Amanda; Davies, Ian R L; Franklin, Anna

2010-10-01

Categorical perception (CP) of color is the faster and/or more accurate discrimination of colors from different categories than equivalently spaced colors from the same category. Here, we investigate whether color CP at early stages of chromatic processing is independent of top-down modulation from attention. A visual oddball task was employed where frequent and infrequent colored stimuli were either same- or different-category, with chromatic differences equated across conditions. Stimuli were presented peripheral to a central distractor task to elicit an event-related potential (ERP) known as the visual mismatch negativity (vMMN). The vMMN is an index of automatic and pre-attentive visual change detection arising from generating loci in visual cortices. The results revealed a greater vMMN for different-category than same-category change detection when stimuli appeared in the lower visual field, and an absence of attention-related ERP components. The findings provide the first clear evidence for an automatic and pre-attentive categorical code for color. Copyright © 2010 Elsevier B.V. All rights reserved.

Effect of Within-Category Spacing on Free Recall

ERIC Educational Resources Information Center

Borges, Marilyn A.; Mandler, George

1972-01-01

Contrary to previous experiments which found recall with blocked spacing always superior to recall with random" spacings, these experiments found that total recall was a function of two independent factors: (a) category representation, and (b) items per category represented (IPC). Both factors are dependent upon within-category spacing.…

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Methane in Metal and Nonmetal Mines Mine Categorization § 57.22003 Mine category or... methane and dusts containing volatile matter. Categories and subcategories are defined as follows: (1) Category I applies to mines that operate within a combustible ore body and either liberate methane or have...

32 CFR 728.113 - Categories of pay patients.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Categories of pay patients. 728.113 Section 728.113 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY PERSONNEL MEDICAL AND... Pay Patients § 728.113 Categories of pay patients. The categories of patients for whom collection...

On the Grothendieck rings of equivariant fusion categories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burciu, Sebastian, E-mail: sebastian.burciu@imar.ro

2015-07-15

In this paper, we describe a Mackey type decomposition for group actions on abelian categories. This allows us to define new Mackey functors which associates to any subgroup the K-theory of the corresponding equivariantized abelian category. In the case of an action by tensor autoequivalences, the Mackey functor at the level of Grothendieck rings has a Green functor structure. As an application we give a description of the Grothendieck rings of equivariantized fusion categories under group actions by tensor autoequivalences on graded fusion categories. In this settings, a new formula for the tensor product of any two simple objects ofmore » an equivariantized fusion category is given, simplifying the fusion formula from Burciu and Natale [J. Math. Phys. 54, 013511 (2013)].« less

Double dissociation of semantic categories in Alzheimer's disease.

PubMed

Gonnerman, L M; Andersen, E S; Devlin, J T; Kempler, D; Seidenberg, M S

1997-04-01

Data that demonstrate distinct patterns of semantic impairment in Alzheimer's disease (AD) are presented. Findings suggest that while groups of mild-moderate patients may not display category specific impairments, some individual patients do show selective impairment of either natural kinds or artifacts. We present a model of semantic organization in which category specific impairments arise from damage to distributed features underlying different types of categories. We incorporate the crucial notions of intercorrelations and distinguishing features, allowing us to demonstrate (1) how category specific impairments can result from widespread damage and (2) how selective deficits in AD reflect different points in the progression of impairment. The different patterns of impairment arise from an interaction between the nature of the semantic categories and the progression of damage.

Statistical Inference in the Learning of Novel Phonetic Categories

ERIC Educational Resources Information Center

Zhao, Yuan

2010-01-01

Learning a phonetic category (or any linguistic category) requires integrating different sources of information. A crucial unsolved problem for phonetic learning is how this integration occurs: how can we update our previous knowledge about a phonetic category as we hear new exemplars of the category? One model of learning is Bayesian Inference,…

Perceptual Versus Semantic Information Processing in Semantic Category Decisions.

ERIC Educational Resources Information Center

Kamil, Michael L.; Hanson, Raymond H.

This study examined the ability of junior high school students to use advance information when making semantic category decisions. The subjects, eight good readers and eight poor readers, identified paired words as "same" or "different" in category, with some words more highly associated with the category than others--in the "fruit" category, for…

14 CFR 29.81 - Landing distance: Category A.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Landing distance: Category A. 29.81 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.81 Landing distance: Category A... knots for water landings) from a point 50 ft above the landing surface must be determined from the...

14 CFR 29.81 - Landing distance: Category A.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Landing distance: Category A. 29.81 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.81 Landing distance: Category A... knots for water landings) from a point 50 ft above the landing surface must be determined from the...

Mere exposure alters category learning of novel objects.

PubMed

Folstein, Jonathan R; Gauthier, Isabel; Palmeri, Thomas J

2010-01-01

We investigated how mere exposure to complex objects with correlated or uncorrelated object features affects later category learning of new objects not seen during exposure. Correlations among pre-exposed object dimensions influenced later category learning. Unlike other published studies, the collection of pre-exposed objects provided no information regarding the categories to be learned, ruling out unsupervised or incidental category learning during pre-exposure. Instead, results are interpreted with respect to statistical learning mechanisms, providing one of the first demonstrations of how statistical learning can influence visual object learning.

Mere Exposure Alters Category Learning of Novel Objects

PubMed Central

Folstein, Jonathan R.; Gauthier, Isabel; Palmeri, Thomas J.

2010-01-01

We investigated how mere exposure to complex objects with correlated or uncorrelated object features affects later category learning of new objects not seen during exposure. Correlations among pre-exposed object dimensions influenced later category learning. Unlike other published studies, the collection of pre-exposed objects provided no information regarding the categories to be learned, ruling out unsupervised or incidental category learning during pre-exposure. Instead, results are interpreted with respect to statistical learning mechanisms, providing one of the first demonstrations of how statistical learning can influence visual object learning. PMID:21833209

The Linguistic Construction of Social Categories in Toddlers

ERIC Educational Resources Information Center

Diesendruck, Gil; Deblinger-Tangi, Ronit

2014-01-01

Kindergarteners treat certain social categories as natural kinds. This study addressed how children pick out social categories. Ninety-one 19-and 26-month-olds were familiarized to exemplars of categories of people (e.g., Blacks-Whites, men-women) and animals (e.g., cows-horses). Participants then saw a picture matching the familiarization…

Comparing English, Mandarin, and Russian Hydrographic and Terrain Categories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Chen-Chieh; Sorokine, Alexandre

The paper compares hydrographic and terrain categories in the geospatial data standards of the US, Taiwan, and Russian Federation where the dominant languages used are from di erent language families. It aims to identify structural and semantic di erences between similar categories across three geospatial data standards. By formalizing the data standard structures and identifying the properties that di erentiate sibling categories in each geospatial data standard using well-known formal relations and quality universals, we develop a common basis on which hydrographic and terrain categories in the three data standards can be compared. The result suggests that all three datamore » standards structure categories with a mixture of relations with di erent meaning even though most of them are well-known relations in top-level ontologies. Similar categories can be found across all three standards but exact match between similar categories are rare.« less

From Statistics to Meaning: Infants’ Acquisition of Lexical Categories

PubMed Central

Lany, Jill; Saffran, Jenny R.

2013-01-01

Infants are highly sensitive to statistical patterns in their auditory language input that mark word categories (e.g., noun and verb). However, it is unknown whether experience with these cues facilitates the acquisition of semantic properties of word categories. In a study testing this hypothesis, infants first listened to an artificial language in which word categories were reliably distinguished by statistical cues (experimental group) or in which these properties did not cue category membership (control group). Both groups were then trained on identical pairings between the words and pictures from two categories (animals and vehicles). Only infants in the experimental group learned the trained associations between specific words and pictures. Moreover, these infants generalized the pattern to include novel pairings. These results suggest that experience with statistical cues marking lexical categories sets the stage for learning the meanings of individual words and for generalizing meanings to new category members. PMID:20424058

Cross-Classification and Category Representation in Children's Concepts

ERIC Educational Resources Information Center

Nguyen, Simone P.

2007-01-01

Items commonly belong to many categories. Cross-classification is the classification of a single item into more than one category. This research explored 2- to 6-year-old children's use of 2 different category systems for cross-classification: script (e.g., school-time items, birthday party items) and taxonomic (e.g., animals, clothes). The…

Quantum Bianchi identities via DG categories

NASA Astrophysics Data System (ADS)

Beggs, Edwin J.; Majid, Shahn

2018-01-01

We use DG categories to derive analogues of the Bianchi identities for the curvature of a connection in noncommutative differential geometry. We also revisit the Chern-Connes pairing but following the line of Chern's original derivation. We show that a related DG category of extendable bimodule connections is a monoidal tensor category and in the metric compatible case obtain an analogue of a classical antisymmetry of the Riemann tensor. The monoidal structure implies the existence of a cup product on noncommutative sheaf cohomology. Another application shows that the curvature of a line module reduces to a 2-form on the base algebra. We illustrate the theory on the q-sphere, the permutation group S3 and the bicrossproduct quantum spacetime [ r , t ] = λr.

Uncovering contrast categories in categorization with a probabilistic threshold model.

PubMed

Verheyen, Steven; De Deyne, Simon; Dry, Matthew J; Storms, Gert

2011-11-01

A contrast category effect on categorization occurs when the decision to apply a category term to an entity not only involves a comparison between the entity and the target category but is also influenced by a comparison of the entity with 1 or more alternative categories from the same domain as the target. Establishing a contrast category effect on categorization in natural language categories has proven to be laborious, especially when the categories concerned are natural kinds situated at the superordinate level of abstraction. We conducted 3 studies with these categories to look for an influence on categorization of both similarity to the target category and similarity to a contrast category. The results are analyzed with a probabilistic threshold model that assumes categorization decisions arise from the placement of threshold criteria by individual categorizers along a single scale that holds the experimental stimuli. The stimuli's positions along the scale are shown to be influenced by similarity to both target and contrast. These findings suggest that the prevalence of contrast category effects on categorization might have been underestimated. Additional analyses demonstrate how the proposed model can be employed in future studies to systematically investigate the origins of contrast category effects on categorization.

Category-Specific Neural Oscillations Predict Recall Organization During Memory Search

PubMed Central

Morton, Neal W.; Kahana, Michael J.; Rosenberg, Emily A.; Baltuch, Gordon H.; Litt, Brian; Sharan, Ashwini D.; Sperling, Michael R.; Polyn, Sean M.

2013-01-01

Retrieved-context models of human memory propose that as material is studied, retrieval cues are constructed that allow one to target particular aspects of past experience. We examined the neural predictions of these models by using electrocorticographic/depth recordings and scalp electroencephalography (EEG) to characterize category-specific oscillatory activity, while participants studied and recalled items from distinct, neurally discriminable categories. During study, these category-specific patterns predict whether a studied item will be recalled. In the scalp EEG experiment, category-specific activity during study also predicts whether a given item will be recalled adjacent to other same-category items, consistent with the proposal that a category-specific retrieval cue is used to guide memory search. Retrieved-context models suggest that integrative neural circuitry is involved in the construction and maintenance of the retrieval cue. Consistent with this hypothesis, we observe category-specific patterns that rise in strength as multiple same-category items are studied sequentially, and find that individual differences in this category-specific neural integration during study predict the degree to which a participant will use category information to organize memory search. Finally, we track the deployment of this retrieval cue during memory search: Category-specific patterns are stronger when participants organize their responses according to the category of the studied material. PMID:22875859

When does fading enhance perceptual category learning?

PubMed

Pashler, Harold; Mozer, Michael C

2013-07-01

Training that uses exaggerated versions of a stimulus discrimination (fading) has sometimes been found to enhance category learning, mostly in studies involving animals and impaired populations. However, little is known about whether and when fading facilitates learning for typical individuals. This issue was explored in 7 experiments. In Experiments 1 and 2, observers discriminated stimuli based on a single sensory continuum (time duration and line length, respectively). Adaptive fading dramatically improved performance in training (unsurprisingly) but did not enhance learning as assessed in a final test. The same was true for nonadaptive linear fading (Experiment 3). However, when variation in length (predicting category membership) was embedded among other (category-irrelevant) variation, fading dramatically enhanced not only performance in training but also learning as assessed in a final test (Experiments 4 and 5). Fading also helped learners to acquire a color saturation discrimination amid category-irrelevant variation in hue and brightness, although this learning proved transitory after feedback was withdrawn (Experiment 7). Theoretical implications are discussed, and we argue that fading should have practical utility in naturalistic category learning tasks, which involve extremely high dimensional stimuli and many irrelevant dimensions. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Prototypes and particulars: geometric and experience-dependent spatial categories.

PubMed

Spencer, John P; Hund, Alycia M

2002-03-01

People use geometric cues to form spatial categories. This study investigated whether people also use the spatial distribution of exemplars. Adults pointed to remembered locations on a tabletop. In Experiment 1, a target was placed in each geometric category, and the location of targets was varied. Adults' responses were biased away from a midline category boundary toward geometric prototypes located at the centers of left and right categories. Experiment 2 showed that prototype effects were not influenced by cross-category interactions. In Experiment 3, subsets of targets were positioned at different locations within each category. When prototype effects were removed, there was a bias toward the center of the exemplar distribution, suggesting that common categorization processes operate across spatial and object domains.

Age of acquisition affects the retrieval of grammatical category information.

PubMed

Bai, Lili; Ma, Tengfei; Dunlap, Susan; Chen, Baoguo

2013-01-01

This study investigated age of acquisition (AoA) effects on processing grammatical category information of Chinese single-character words. In Experiment 1, nouns and verbs that were acquired at different ages were used as materials in a grammatical category decision task. Results showed that the grammatical category information of earlier acquired nouns and verbs was easier to retrieve. In Experiment 2, AoA and predictability from orthography to grammatical category were manipulated in a grammatical category decision task. Results showed larger AoA effects under lower predictability conditions. In Experiment 3, a semantic category decision task was used with the same materials as those in Experiment 2. Different results were found from Experiment 2, suggesting that the grammatical category decision task is not merely the same as the semantic category decision task, but rather involves additional processing of grammatical category information. Therefore the conclusions of Experiments 1 and 2 were strengthened. In summary, it was found for the first time that AoA affects the retrieval of grammatical category information, thus providing new evidence in support of the arbitrary mapping hypothesis.

Fabric circuits and method of manufacturing fabric circuits

NASA Technical Reports Server (NTRS)

Chu, Andrew W. (Inventor); Dobbins, Justin A. (Inventor); Scully, Robert C. (Inventor); Trevino, Robert C. (Inventor); Lin, Greg Y. (Inventor); Fink, Patrick W. (Inventor)

2011-01-01

A flexible, fabric-based circuit comprises a non-conductive flexible layer of fabric and a conductive flexible layer of fabric adjacent thereto. A non-conductive thread, an adhesive, and/or other means may be used for attaching the conductive layer to the non-conductive layer. In some embodiments, the layers are attached by a computer-driven embroidery machine at pre-determined portions or locations in accordance with a pre-determined attachment layout before automated cutting. In some other embodiments, an automated milling machine or a computer-driven laser using a pre-designed circuit trace as a template cuts the conductive layer so as to separate an undesired portion of the conductive layer from a desired portion of the conductive layer. Additional layers of conductive fabric may be attached in some embodiments to form a multi-layer construct.

Trace of the Twisted Heisenberg Category

NASA Astrophysics Data System (ADS)

Oğuz, Can Ozan; Reeks, Michael

2017-12-01

We show that the trace decategorification, or zeroth Hochschild homology, of the twisted Heisenberg category defined by Cautis and Sussan is isomorphic to a quotient of {W^-}, a subalgebra of W_{1+∞} defined by Kac, Wang, and Yan. Our result is a twisted analogue of that by Cautis, Lauda, Licata, and Sussan relating W_{1+∞} and the trace decategorification of the Heisenberg category.

Uncovering Contrast Categories in Categorization with a Probabilistic Threshold Model

ERIC Educational Resources Information Center

Verheyen, Steven; De Deyne, Simon; Dry, Matthew J.; Storms, Gert

2011-01-01

A contrast category effect on categorization occurs when the decision to apply a category term to an entity not only involves a comparison between the entity and the target category but is also influenced by a comparison of the entity with 1 or more alternative categories from the same domain as the target. Establishing a contrast category effect…

Categorical perception of color: evidence from secondary category boundary

PubMed Central

Al-rasheed, Abdulrahman Saud

2015-01-01

Despite a plethora of behavioral research exploring the phenomenon of color categorical perception (CP) known as “better discrimination between pair of colors stimuli from different categories and pair of colors stimuli from the same category even when the stimulus differences between the pairs of stimuli are equal”, most of the evidence for the CP of color was derived from Roman or top-to-down script readers and very rarely from right-to-left script readers in primary category. To date, no studies of color CP have been conducted on right-to-left script readers in secondary category boundary to support this theory. Three experiments have been conducted: Experiments 1 and 2 established the Arabic blue–purple secondary category boundary, and Experiment 3 tested the CP of color in the blue–purple category boundary. Sixty participants (30 men and 30 women) took part in this study. All spoke Arabic as their first language, and all were undergraduate or postgraduate students at King Saud University. Their ages ranged from 18–35 years with a mean age of 21.9 years (SD =5.2). The result indicated that for Experiments 1 and 2, it appeared that the Arabic blue–purple category boundary was approximately 10PB and it is in the same location as for English. For Experiment 3, reaction times in the between-categories condition were significantly faster than those in the within-category condition; this suggested that CP of color was shown in the Arabic’s blue–purple secondary category boundary. PMID:26648764

Correspondence between Grammatical Categories and Grammatical Functions in Chinese.

ERIC Educational Resources Information Center

Tan, Fu

1993-01-01

A correspondence is shown between grammatical categories and grammatical functions in Chinese. Some syntactic properties distinguish finite verbs from nonfinite verbs, nominals from other categories, and verbs from other categories. (Contains seven references.) (LB)

Multimedia category preferences of working engineers

NASA Astrophysics Data System (ADS)

Baukal, Charles E.; Ausburn, Lynna J.

2016-09-01

Many have argued for the importance of continuing engineering education (CEE), but relatively few recommendations were found in the literature for how to use multimedia technologies to deliver it most effectively. The study reported here addressed this gap by investigating the multimedia category preferences of working engineers. Four categories of multimedia, with two types in each category, were studied: verbal (text and narration), static graphics (drawing and photograph), dynamic non-interactive graphics (animation and video), and dynamic interactive graphics (simulated virtual reality (VR) and photo-real VR). The results showed that working engineers strongly preferred text over narration and somewhat preferred drawing over photograph, animation over video, and simulated VR over photo-real VR. These results suggest that a variety of multimedia types should be used in the instructional design of CEE content.

28 CFR 94.22 - Categories of expenses.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Categories of expenses. 94.22 Section 94.22 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CRIME VICTIM SERVICES International Terrorism Victim Expense Reimbursement Program Coverage § 94.22 Categories of expenses. The following...

28 CFR 94.22 - Categories of expenses.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Categories of expenses. 94.22 Section 94.22 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CRIME VICTIM SERVICES International Terrorism Victim Expense Reimbursement Program Coverage § 94.22 Categories of expenses. The following...

28 CFR 94.22 - Categories of expenses.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Categories of expenses. 94.22 Section 94.22 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CRIME VICTIM SERVICES International Terrorism Victim Expense Reimbursement Program Coverage § 94.22 Categories of expenses. The following...

28 CFR 94.22 - Categories of expenses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 2 2011-07-01 2011-07-01 false Categories of expenses. 94.22 Section 94.22 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CRIME VICTIM SERVICES International Terrorism Victim Expense Reimbursement Program Coverage § 94.22 Categories of expenses. The following...

28 CFR 94.22 - Categories of expenses.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Categories of expenses. 94.22 Section 94.22 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) CRIME VICTIM SERVICES International Terrorism Victim Expense Reimbursement Program Coverage § 94.22 Categories of expenses. The following...

Blunt Trauma Performance of Fabric Systems Utilizing Natural Rubber Coated High Strength Fabrics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmad, M. R.; Ahmad, W. Y. W.; Samsuri, A.

2010-03-11

The blunt trauma performance of fabric systems against 9 mm bullets is reported. Three shots were fired at each fabric system with impact velocity of 367+-9 m/s and the depth of indentation on the modeling clay backing was measured. The results showed that 18-layer and 21-layer all-neat fabric systems failed the blunt trauma test. However, fabric systems with natural rubber (NR) latex coated fabric layers gave lower blunt trauma of between 25-32 mm indentation depths. Deformations on the neat fabrics upon impact were identified as broken yarns, yarn stretching and yarn pull-out. Deflections of the neat fabrics were more localised.more » For the NR latex coated fabric layers, no significant deformation can be observed except for peeled-off regions of the NR latex film at the back surface of the last layer. From the study, it can be said that the NR latex coated fabric layers were effective in reducing the blunt trauma of fabric systems.« less

The Role of Corticostriatal Systems in Speech Category Learning

PubMed Central

Yi, Han-Gyol; Maddox, W. Todd; Mumford, Jeanette A.; Chandrasekaran, Bharath

2016-01-01

One of the most difficult category learning problems for humans is learning nonnative speech categories. While feedback-based category training can enhance speech learning, the mechanisms underlying these benefits are unclear. In this functional magnetic resonance imaging study, we investigated neural and computational mechanisms underlying feedback-dependent speech category learning in adults. Positive feedback activated a large corticostriatal network including the dorsolateral prefrontal cortex, inferior parietal lobule, middle temporal gyrus, caudate, putamen, and the ventral striatum. Successful learning was contingent upon the activity of domain-general category learning systems: the fast-learning reflective system, involving the dorsolateral prefrontal cortex that develops and tests explicit rules based on the feedback content, and the slow-learning reflexive system, involving the putamen in which the stimuli are implicitly associated with category responses based on the reward value in feedback. Computational modeling of response strategies revealed significant use of reflective strategies early in training and greater use of reflexive strategies later in training. Reflexive strategy use was associated with increased activation in the putamen. Our results demonstrate a critical role for the reflexive corticostriatal learning system as a function of response strategy and proficiency during speech category learning. Keywords: category learning, fMRI, corticostriatal systems, speech, putamen PMID:25331600

A Bulk Microphysics Parameterization with Multiple Ice Precipitation Categories.

NASA Astrophysics Data System (ADS)

Straka, Jerry M.; Mansell, Edward R.

2005-04-01

A single-moment bulk microphysics scheme with multiple ice precipitation categories is described. It has 2 liquid hydrometeor categories (cloud droplets and rain) and 10 ice categories that are characterized by habit, size, and density—two ice crystal habits (column and plate), rimed cloud ice, snow (ice crystal aggregates), three categories of graupel with different densities and intercepts, frozen drops, small hail, and large hail. The concept of riming history is implemented for conversions among the graupel and frozen drops categories. The multiple precipitation ice categories allow a range of particle densities and fall velocities for simulating a variety of convective storms with minimal parameter tuning. The scheme is applied to two cases—an idealized continental multicell storm that demonstrates the ice precipitation process, and a small Florida maritime storm in which the warm rain process is important.

Effect of between-category similarity on basic-level superiority in pigeons

PubMed Central

Lazareva, Olga F.; Soto, Fabián A.; Wasserman, Edward A.

2010-01-01

Children categorize stimuli at the basic level faster than at the superordinate level. We hypothesized that between-category similarity may affect this basic-level superiority effect. Dissimilar categories may be easy to distinguish at the basic level but be difficult to group at the superordinate level, whereas similar categories may be easy to group at the superordinate level but be difficult to distinguish at the basic level. Consequently, similar basic-level categories may produce a superordinate-before-basic learning trend, whereas dissimilar basic-level categories may result in a basic-before-superordinate learning trend. We tested this hypothesis in pigeons by constructing superordinate-level categories out of basic-level categories with known similarity. In Experiment 1, we experimentally evaluated the between-category similarity of four basic-level photographic categories using multiple fixed interval-extinction training (Astley & Wasserman, 1992). We used the resultant similarity matrices in Experiment 2 to construct two superordinate-level categories from basic-level categories with high between-category similarity (cars and persons; chairs and flowers). We then trained pigeons to concurrently classify those photographs into either the proper basic-level category or the proper superordinate-level category. Under these conditions, the pigeons learned the superordinate-level discrimination faster than the basic-level discrimination, confirming our hypothesis that basic-level superiority is affected by between-category similarity. PMID:20600696

Generalized Categorial Grammar for Unbounded Dependencies Recovery

ERIC Educational Resources Information Center

Nguyen, Luan Viet

2014-01-01

Accurate recovery of predicate-argument dependencies is vital for interpretation tasks like information extraction and question answering, and unbounded dependencies may account for a significant portion of the dependencies in any given text. This thesis describes a Generalized Categorial Grammar (GCG) which, like other categorial grammars,…

Influence of multiple categories on the prediction of unknown properties

PubMed Central

Verde, Michael F.; Murphy, Gregory L.; Ross, Brian H.

2006-01-01

Knowing an item's category helps us predict its unknown properties. Previous studies suggest that when asked to evaluate the probability of an unknown property, people tend to consider only an item's most likely category, ignoring alternative categories. In the present study, property prediction took the form of either a probability rating or a speeded, binary-choice judgment. Consistent with past findings, subjects ignored alternative categories in their probability ratings. However, their binary-choice judgments were influenced by alternative categories. This novel finding suggests that the way category knowledge is used in prediction depends critically on the form of the prediction. PMID:16156183

32 CFR 901.3 - Categories of nominations for appointment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 901.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE MILITARY... of military or civilian personnel in missing status competitive category. (e) Honor military and... Officers' Training Corps (AFJROTC) competitive category. (f) Children of Medal of Honor recipients category...

Feature highlighting enhances learning of a complex natural-science category.

PubMed

Miyatsu, Toshiya; Gouravajhala, Reshma; Nosofsky, Robert M; McDaniel, Mark A

2018-04-26

Learning naturalistic categories, which tend to have fuzzy boundaries and vary on many dimensions, can often be harder than learning well defined categories. One method for facilitating the category learning of naturalistic stimuli may be to provide explicit feature descriptions that highlight the characteristic features of each category. Although this method is commonly used in textbooks and classrooms, theoretically it remains uncertain whether feature descriptions should advantage learning complex natural-science categories. In three experiments, participants were trained on 12 categories of rocks, either without or with a brief description highlighting key features of each category. After training, they were tested on their ability to categorize both old and new rocks from each of the categories. Providing feature descriptions as a caption under a rock image failed to improve category learning relative to providing only the rock image with its category label (Experiment 1). However, when these same feature descriptions were presented such that they were explicitly linked to the relevant parts of the rock image (feature highlighting), participants showed significantly higher performance on both immediate generalization to new rocks (Experiment 2) and generalization after a 2-day delay (Experiment 3). Theoretical and practical implications are discussed. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Concept Categories as Measures of Culture Distance.

ERIC Educational Resources Information Center

Mackey, William F.

The research reported in this paper tests the possibility of using differences in conceptual categories in the measurement of differences between two cultures. In the initial experiment, which contrasts French and French-Acadian linguistic habits, the authors limit themselves to conceptual categories reflected in concrete nouns representing the…

40 CFR 220.3 - Categories of permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Categories of permits. 220.3 Section 220.3 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING GENERAL § 220.3 Categories of permits. This § 220.3 provides for the issuance of general, special, emergency...

40 CFR 220.3 - Categories of permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Categories of permits. 220.3 Section 220.3 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING GENERAL § 220.3 Categories of permits. This § 220.3 provides for the issuance of general, special, emergency...

14 CFR 29.71 - Helicopter angle of glide: Category B.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Helicopter angle of glide: Category B. 29... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.71 Helicopter angle of glide: Category B. For each category B helicopter, except multiengine helicopters meeting the...

14 CFR 29.71 - Helicopter angle of glide: Category B.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Helicopter angle of glide: Category B. 29... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.71 Helicopter angle of glide: Category B. For each category B helicopter, except multiengine helicopters meeting the...

14 CFR 29.71 - Helicopter angle of glide: Category B.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Helicopter angle of glide: Category B. 29... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.71 Helicopter angle of glide: Category B. For each category B helicopter, except multiengine helicopters meeting the...

14 CFR 29.71 - Helicopter angle of glide: Category B.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Helicopter angle of glide: Category B. 29... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.71 Helicopter angle of glide: Category B. For each category B helicopter, except multiengine helicopters meeting the...

14 CFR 29.71 - Helicopter angle of glide: Category B.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Helicopter angle of glide: Category B. 29... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.71 Helicopter angle of glide: Category B. For each category B helicopter, except multiengine helicopters meeting the...

Decoding the neural representation of fine-grained conceptual categories.

PubMed

Ghio, Marta; Vaghi, Matilde Maria Serena; Perani, Daniela; Tettamanti, Marco

2016-05-15

Neuroscientific research on conceptual knowledge based on the grounded cognition framework has shed light on the organization of concrete concepts into semantic categories that rely on different types of experiential information. Abstract concepts have traditionally been investigated as an undifferentiated whole, and have only recently been addressed in a grounded cognition perspective. The present fMRI study investigated the involvement of brain systems coding for experiential information in the conceptual processing of fine-grained semantic categories along the abstract-concrete continuum. These categories consisted of mental state-, emotion-, mathematics-, mouth action-, hand action-, and leg action-related meanings. Thirty-five sentences for each category were used as stimuli in a 1-back task performed by 36 healthy participants. A univariate analysis failed to reveal category-specific activations. Multivariate pattern analyses, in turn, revealed that fMRI data contained sufficient information to disentangle all six fine-grained semantic categories across participants. However, the category-specific activity patterns showed no overlap with the regions coding for experiential information. These findings demonstrate the possibility of detecting specific patterns of neural representation associated with the processing of fine-grained conceptual categories, crucially including abstract ones, though bearing no anatomical correspondence with regions coding for experiential information as predicted by the grounded cognition hypothesis. Copyright © 2016 Elsevier Inc. All rights reserved.

Novel Composites for Wing and Fuselage Applications. Task 1; Novel Wing Design Concepts

NASA Technical Reports Server (NTRS)

Suarez, J. A.; Buttitta, C.; Flanagan, G.; DeSilva, T.; Egensteiner, W.; Bruno, J.; Mahon, J.; Rutkowski, C.; Collins, R.; Fidnarick, R.;

1 CFR 5.9 - Categories of documents.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Categories of documents. 5.9 Section 5.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.9 Categories of documents. Each document published in the Federal Register shall be placed under one of the...

1 CFR 5.9 - Categories of documents.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 1 General Provisions 1 2011-01-01 2011-01-01 false Categories of documents. 5.9 Section 5.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.9 Categories of documents. Each document published in the Federal Register shall be placed under one of the...

Rule-Based Category Learning in Down Syndrome

ERIC Educational Resources Information Center

Phillips, B. Allyson; Conners, Frances A.; Merrill, Edward; Klinger, Mark R.

2014-01-01

Rule-based category learning was examined in youths with Down syndrome (DS), youths with intellectual disability (ID), and typically developing (TD) youths. Two tasks measured category learning: the Modified Card Sort task (MCST) and the Concept Formation test of the Woodcock-Johnson-III (Woodcock, McGrew, & Mather, 2001). In regression-based…

1 CFR 5.9 - Categories of documents.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 1 General Provisions 1 2012-01-01 2012-01-01 false Categories of documents. 5.9 Section 5.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.9 Categories of documents. Each document published in the Federal Register shall be placed under one of the...

40 CFR 98.160 - Definition of the source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Hydrogen Production § 98.160 Definition of the source category. (a) A hydrogen production source category consists of facilities that produce hydrogen gas sold as a product to other entities. (b) This source category comprises process units that produce hydrogen by...

40 CFR 98.160 - Definition of the source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Hydrogen Production § 98.160 Definition of the source category. (a) A hydrogen production source category consists of facilities that produce hydrogen gas sold as a product to other entities. (b) This source category comprises process units that produce hydrogen by...

40 CFR 98.160 - Definition of the source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Hydrogen Production § 98.160 Definition of the source category. (a) A hydrogen production source category consists of facilities that produce hydrogen gas sold as a product to other entities. (b) This source category comprises process units that produce hydrogen by...

40 CFR 98.160 - Definition of the source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Hydrogen Production § 98.160 Definition of the source category. (a) A hydrogen production source category consists of facilities that produce hydrogen gas sold as a product to other entities. (b) This source category comprises process units that produce hydrogen by...

40 CFR 98.160 - Definition of the source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Hydrogen Production § 98.160 Definition of the source category. (a) A hydrogen production source category consists of facilities that produce hydrogen gas sold as a product to other entities. (b) This source category comprises process units that produce hydrogen by...

Effects of generic language on category content and structure.

PubMed

Gelman, Susan A; Ware, Elizabeth A; Kleinberg, Felicia

2010-11-01

We hypothesized that generic noun phrases ("Bears climb trees") would provide important input to children's developing concepts. In three experiments, four-year-olds and adults learned a series of facts about a novel animal category, in one of three wording conditions: generic (e.g., "Zarpies hate ice cream"), specific-label (e.g., "This zarpie hates ice cream"), or no-label (e.g., "This hates ice cream"). Participants completed a battery of tasks assessing the extent to which they linked the category to the properties expressed, and the extent to which they treated the category as constituting an essentialized kind. As predicted, for adults, generics training resulted in tighter category-property links and more category essentialism than both the specific-label and no-label training. Children also showed effects of generic wording, though the effects were weaker and required more extensive input. We discuss the implications for language-thought relations, and for the acquisition of essentialized categories. Copyright 2010 Elsevier Inc. All rights reserved.

Green synthesis of AuNPs for eco-friendly functionalization of cellulosic substrates

NASA Astrophysics Data System (ADS)

Ibrahim, Nabil A.; Eid, Basma M.; Abdel-Aziz, Mohamed S.

2016-12-01

In this research work, extracellular biosynthesis of gold nanoparticles (AuNPs) using marine bacterial isolates (Streptomyces sp.) as a reducing/capping/stabilizing bio-agent and chlolauric acid (HAuCl4) as a precursor has been investigated. Surface modification of cotton and viscose knitted fabrics using O2-plasma followed by subsequent treatment with bio-synthesized AuNPs alone and in combination with TiO2NPs or ZnONPs to impart new functional properties namely antibacterial and UV-blocking were studied. The results show that loading of nominated nanomaterials onto the activated fabric samples results in a significant improvement in antibacterial activity against both G+ve (S. aureus) and G-ve (E. coli) along with a remarkable enhancement in the UV-protection functionality of the treated fabrics. The highest antibacterial and anti-UV values were obtained when O2-plasma treated fabrics were loaded with AuNPs/ZnONPs combination, irrespective of the used substrate. The imparted functional properties demonstrated remarkable retention even after 15 washings.

Appropriate Pupilness: Social Categories Intersecting in School

ERIC Educational Resources Information Center

Kofoed, Jette

2008-01-01

The analytical focus in this article is on how social categories intersect in daily school life and how intersections intertwine with other empirically relevant categories such as normality, pupilness and (in)appropriatedness. The point of empirical departure is a daily ritual where teams for football are selected. The article opens up for a…

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

1 CFR 5.9 - Categories of documents.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 1 General Provisions 1 2013-01-01 2012-01-01 true Categories of documents. 5.9 Section 5.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.9 Categories of documents. Each document published in the Federal Register shall be placed under one of the following...

1 CFR 5.9 - Categories of documents.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 1 General Provisions 1 2014-01-01 2012-01-01 true Categories of documents. 5.9 Section 5.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.9 Categories of documents. Each document published in the Federal Register shall be placed under one of the following...

Pre-vitamin D effective ultraviolet transmission through clothing during simulated wear.

PubMed

Parisi, A V; Wilson, C A

2005-12-01

Clothing is an important protective layer used to reduce ultraviolet (UV) exposures to the skin surface. However, not all UV exposure is linked to detrimental health effects with some exposure to UVB wavelengths below 316 nm required for the synthesis of pre-vitamin D(3). The aim of the current research was to investigate the effect of fabric type, color, fit, and wetness on the transmission of pre-vitamin D(3) effective UV through garments during simulated wear, in a high UV exposure environment. Dosimeters fabricated from polysulfone film were positioned at eight selected body sites on the skin surface and clothing surface of identically designed, loose and fitted, black and white T-shirts made up in two knitted fabric types and tested when both dry and when drying after initial wetting (n=3 replicates). The T-shirts were placed on manikins set to simulate humans in the sun between 09:30 and 12:30 Eastern Standard Time during the Southern Hemisphere summer period. The post-exposure absorbance was measured and the dosimeters were calibrated for biologically effective UV for pre-vitamin D(3) synthesis with a UV spectroradiometer. The effect of fit, fabric type, color, and wetness on pre-vitamin D(3) effective UV transmission during simulated wear was assessed. Irradiances varied among body sites with the highest erythemal exposures to a horizontal plane over the 3 h period reaching approximately 14.5 minimal erythema dose (MED) while the highest exposure under the garment was 0.22 MED which may not be above the threshold for pre-vitamin D(3) synthesis for the time period investigated. Fabric and fit were the main variables affecting transmission of pre-vitamin D(3) effective UV. Some interactions were identified between the fabric color and wetness and between fabric type and color; however, while significantly modifying transmission these effects were small. Transmission of pre-vitamin D(3) effective UV occurred through the high UPF knitted fabrics investigated

Chromatic Perceptual Learning but No Category Effects without Linguistic Input.

PubMed

Grandison, Alexandra; Sowden, Paul T; Drivonikou, Vicky G; Notman, Leslie A; Alexander, Iona; Davies, Ian R L

2016-01-01

Perceptual learning involves an improvement in perceptual judgment with practice, which is often specific to stimulus or task factors. Perceptual learning has been shown on a range of visual tasks but very little research has explored chromatic perceptual learning. Here, we use two low level perceptual threshold tasks and a supra-threshold target detection task to assess chromatic perceptual learning and category effects. Experiment 1 investigates whether chromatic thresholds reduce as a result of training and at what level of analysis learning effects occur. Experiment 2 explores the effect of category training on chromatic thresholds, whether training of this nature is category specific and whether it can induce categorical responding. Experiment 3 investigates the effect of category training on a higher level, lateralized target detection task, previously found to be sensitive to category effects. The findings indicate that performance on a perceptual threshold task improves following training but improvements do not transfer across retinal location or hue. Therefore, chromatic perceptual learning is category specific and can occur at relatively early stages of visual analysis. Additionally, category training does not induce category effects on a low level perceptual threshold task, as indicated by comparable discrimination thresholds at the newly learned hue boundary and adjacent test points. However, category training does induce emerging category effects on a supra-threshold target detection task. Whilst chromatic perceptual learning is possible, learnt category effects appear to be a product of left hemisphere processing, and may require the input of higher level linguistic coding processes in order to manifest.

Chromatic Perceptual Learning but No Category Effects without Linguistic Input

PubMed Central

Grandison, Alexandra; Sowden, Paul T.; Drivonikou, Vicky G.; Notman, Leslie A.; Alexander, Iona; Davies, Ian R. L.

2016-01-01

Perceptual learning involves an improvement in perceptual judgment with practice, which is often specific to stimulus or task factors. Perceptual learning has been shown on a range of visual tasks but very little research has explored chromatic perceptual learning. Here, we use two low level perceptual threshold tasks and a supra-threshold target detection task to assess chromatic perceptual learning and category effects. Experiment 1 investigates whether chromatic thresholds reduce as a result of training and at what level of analysis learning effects occur. Experiment 2 explores the effect of category training on chromatic thresholds, whether training of this nature is category specific and whether it can induce categorical responding. Experiment 3 investigates the effect of category training on a higher level, lateralized target detection task, previously found to be sensitive to category effects. The findings indicate that performance on a perceptual threshold task improves following training but improvements do not transfer across retinal location or hue. Therefore, chromatic perceptual learning is category specific and can occur at relatively early stages of visual analysis. Additionally, category training does not induce category effects on a low level perceptual threshold task, as indicated by comparable discrimination thresholds at the newly learned hue boundary and adjacent test points. However, category training does induce emerging category effects on a supra-threshold target detection task. Whilst chromatic perceptual learning is possible, learnt category effects appear to be a product of left hemisphere processing, and may require the input of higher level linguistic coding processes in order to manifest. PMID:27252669

Behavioral demand modulates object category representation in the inferior temporal cortex

PubMed Central

Emadi, Nazli

2014-01-01

Visual object categorization is a critical task in our daily life. Many studies have explored category representation in the inferior temporal (IT) cortex at the level of single neurons and population. However, it is not clear how behavioral demands modulate this category representation. Here, we recorded from the IT single neurons in monkeys performing two different tasks with identical visual stimuli: passive fixation and body/object categorization. We found that category selectivity of the IT neurons was improved in the categorization compared with the passive task where reward was not contingent on image category. The category improvement was the result of larger rate enhancement for the preferred category and smaller response variability for both preferred and nonpreferred categories. These specific modulations in the responses of IT category neurons enhanced signal-to-noise ratio of the neural responses to discriminate better between the preferred and nonpreferred categories. Our results provide new insight into the adaptable category representation in the IT cortex, which depends on behavioral demands. PMID:25080572

The influence of category coherence on inference about cross-classified entities.

PubMed

Patalano, Andrea L; Wengrovitz, Steven M; Sharpes, Kirsten M

2009-01-01

A critical function of categories is their use in property inference (Heit, 2000). However, one challenge to using categories in inference is that most entities in the world belong to multiple categories (e.g., Fido could be a dog, a pet, a mammal, or a security system). Building on Patalano, Chin-Parker, and Ross (2006), we tested the hypothesis that category coherence (the extent to which category features go together in light of prior knowledge) influences the selection of categories for use in property inference about cross-classified entities. In two experiments, we directly contrasted coherent and incoherent categories, both of which included cross-classified entities as members, and we found that the coherent categories were used more readily as the source of both property transfer and property extension. We conclude that category coherence, which has been found to be a potent influence on strength of inference for singly classified entities (Rehder & Hastie, 2004), is also central to category use in reasoning about novel cross-classified ones.

Object-graphs for context-aware visual category discovery.

PubMed

Lee, Yong Jae; Grauman, Kristen

2012-02-01

How can knowing about some categories help us to discover new ones in unlabeled images? Unsupervised visual category discovery is useful to mine for recurring objects without human supervision, but existing methods assume no prior information and thus tend to perform poorly for cluttered scenes with multiple objects. We propose to leverage knowledge about previously learned categories to enable more accurate discovery, and address challenges in estimating their familiarity in unsegmented, unlabeled images. We introduce two variants of a novel object-graph descriptor to encode the 2D and 3D spatial layout of object-level co-occurrence patterns relative to an unfamiliar region and show that by using them to model the interaction between an image’s known and unknown objects, we can better detect new visual categories. Rather than mine for all categories from scratch, our method identifies new objects while drawing on useful cues from familiar ones. We evaluate our approach on several benchmark data sets and demonstrate clear improvements in discovery over conventional purely appearance-based baselines.

Strategies for generating multiple instances of common and ad hoc categories.

PubMed

Vallée-Tourangeau, F; Anthony, S H; Austin, N G

1998-09-01

In a free-emission procedure participants were asked to generate instances of a given category and to report, retrospectively, the strategies that they were aware of using in retrieving instances. In two studies reported here, participants generated instances for common categories (e.g. fruit) and for ad hoc categories (e.g., things people keep in their pockets) for 90 seconds and for each category described how they had proceeded in doing so. Analysis of the protocols identified three broad classes of strategy: (1) experiential, where memories of specific or generic personal experiences involving interactions with the category instances acted as cues; (2) semantic, where a consideration of abstract conceptual characteristics of a category were employed to retrieve category exemplars; (3) unmediated, where instances were effortlessly retrieved without mediating cognitions of which subjects were aware. Experiential strategies outnumbered semantic strategies (on average 4 to 1) not only for ad hoc categories but also for common categories. This pattern was noticeably reversed for ad hoc categories that subjects were unlikely to have experienced personally (e.g. things sold on the black market in Russia). Whereas more traditional accounts of semantic memory have favoured decontextualised abstract representations of category knowledge, to the extent that mode of access informs us of knowledge structures, our data suggest that category knowledge is significantly grounded in terms of everyday contexts where category instances are encountered.

New Chemicals Program under TSCA Chemical Categories Document

EPA Pesticide Factsheets

The categories included in this compilation represent chemicals for which sufficient assessment experience has been accumulated so that hazard concerns and testing recommendations vary little from chemical to chemical within the category.

Empirical Validation of a New Category System: One Example.

ERIC Educational Resources Information Center

Rosenshine, Barak; And Others

This study found that data from previous research can be used to validate a new observational category system and that subscripting of the original ten categories of the Flanders Interaction Analysis System is useful in identifying more specific behaviors which correlate with student achievement. The new category system was the Expanded…

SUSTAIN: A Network Model of Category Learning

ERIC Educational Resources Information Center

Love, Bradley C.; Medin, Douglas L.; Gureckis, Todd M.

2004-01-01

SUSTAIN (Supervised and Unsupervised STratified Adaptive Incremental Network) is a model of how humans learn categories from examples. SUSTAIN initially assumes a simple category structure. If simple solutions prove inadequate and SUSTAIN is confronted with a surprising event (e.g., it is told that a bat is a mammal instead of a bird), SUSTAIN…

36 CFR 292.22 - Land category assignments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... availability of this map or maps in the local newspapers of record. (b) Changes in land category assignment.../grazing land so long as the intended use or development is consistent with the standards in § 292.23 and... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Land category assignments...

A role for the developing lexicon in phonetic category acquisition

PubMed Central

Feldman, Naomi H.; Griffiths, Thomas L.; Goldwater, Sharon; Morgan, James L.

2013-01-01

Infants segment words from fluent speech during the same period when they are learning phonetic categories, yet accounts of phonetic category acquisition typically ignore information about the words in which sounds appear. We use a Bayesian model to illustrate how feedback from segmented words might constrain phonetic category learning by providing information about which sounds occur together in words. Simulations demonstrate that word-level information can successfully disambiguate overlapping English vowel categories. Learning patterns in the model are shown to parallel human behavior from artificial language learning tasks. These findings point to a central role for the developing lexicon in phonetic category acquisition and provide a framework for incorporating top-down constraints into models of category learning. PMID:24219848

Optimality of the basic colour categories for classification

PubMed Central

Griffin, Lewis D

2005-01-01

Categorization of colour has been widely studied as a window into human language and cognition, and quite separately has been used pragmatically in image-database retrieval systems. This suggests the hypothesis that the best category system for pragmatic purposes coincides with human categories (i.e. the basic colours). We have tested this hypothesis by assessing the performance of different category systems in a machine-vision task. The task was the identification of the odd-one-out from triples of images obtained using a web-based image-search service. In each triple, two of the images had been retrieved using the same search term, the other a different term. The terms were simple concrete nouns. The results were as follows: (i) the odd-one-out task can be performed better than chance using colour alone; (ii) basic colour categorization performs better than random systems of categories; (iii) a category system that performs better than the basic colours could not be found; and (iv) it is not just the general layout of the basic colours that is important, but also the detail. We conclude that (i) the results support the plausibility of an explanation for the basic colours as a result of a pressure-to-optimality and (ii) the basic colours are good categories for machine vision image-retrieval systems. PMID:16849219

Clarifying color category border according to color vision

NASA Astrophysics Data System (ADS)

Ichihara, Takumi; Ichihara, Yasuyo G.

2015-01-01

We usually recognize color by two kinds of processes. In the first, the color is recognized continually and a small difference in color is recognized. In the second, the color is recognized discretely. This process recognizes a similar color of a certain range as being in the same color category. The small difference in color is ignored. Recognition by using the color category is important for communication using color. It is known that a color vision defect confuses colors on the confusion locus of color. However, the color category of a color vision defect has not been thoroughly researched. If the color category of the color vision defect is clarified, it will become an important key for color universal design. In this research, we classified color stimuli into four categories to check the shape and the border of the color categories of varied color vision. The experimental result was as follows. The border of protanopia is the following three on the CIE 1931 (x, y) chromaticity diagram: y = -0.3068x + 0.4795, y = -0.1906x + 0.4021, y = -0.2624x + 0.3896. The border of deuteranopia is the following three on the CIE 1931 (x, y) chromaticity diagram: y = -0.7931x + 0.7036, y = -0.718x + 0.5966, y = -0.6667x + 0.5061.

FDA pregnancy risk categories and the CPS

PubMed Central

Law, Ruth; Bozzo, Pina; Koren, Gideon; Einarson, Adrienne

2010-01-01

ABSTRACT QUESTION My patient is taking a medication for a chronic condition and has just found out that she is 6 weeks pregnant. The US Food and Drug Administration (FDA) has assigned this medication to pregnancy risk category D, and the Compendium of Pharmaceuticals and Specialties provides no additional data. How should I interpret this information, and how does the Motherisk Program evaluate the safety or risks of drug use in pregnancy? ANSWER Pregnancy safety data provided by the FDA pregnancy risk categories and the Compendium of Pharmaceuticals and Specialties are insufficient to guide clinical decisions on how to proceed with a pregnancy following exposure to a category D medication. The Motherisk Program creates peer-reviewed statements derived from the primary literature, and we examine fetal outcomes as well as the risk-benefit profile of maternal treatment when evaluating the safety of medication use in pregnancy. The FDA announced in May 2008 that it is dropping its pregnancy risk categories and adopting a method similar to the one we use at Motherisk. PMID:20228306

Photochemical cutting of fabrics

DOEpatents

Piltch, Martin S.

1994-01-01

Apparatus for the cutting of garment patterns from one or more layers of fabric. A laser capable of producing laser light at an ultraviolet wavelength is utilized to shine light through a pattern, such as a holographic phase filter, and through a lens onto the one or more layers of fabric. The ultraviolet laser light causes rapid photochemical decomposition of the one or more layers of fabric, but only along the pattern. The balance of the fabric of the one or more layers of fabric is undamaged.

The Role of Corticostriatal Systems in Speech Category Learning.

PubMed

Yi, Han-Gyol; Maddox, W Todd; Mumford, Jeanette A; Chandrasekaran, Bharath

2016-04-01

One of the most difficult category learning problems for humans is learning nonnative speech categories. While feedback-based category training can enhance speech learning, the mechanisms underlying these benefits are unclear. In this functional magnetic resonance imaging study, we investigated neural and computational mechanisms underlying feedback-dependent speech category learning in adults. Positive feedback activated a large corticostriatal network including the dorsolateral prefrontal cortex, inferior parietal lobule, middle temporal gyrus, caudate, putamen, and the ventral striatum. Successful learning was contingent upon the activity of domain-general category learning systems: the fast-learning reflective system, involving the dorsolateral prefrontal cortex that develops and tests explicit rules based on the feedback content, and the slow-learning reflexive system, involving the putamen in which the stimuli are implicitly associated with category responses based on the reward value in feedback. Computational modeling of response strategies revealed significant use of reflective strategies early in training and greater use of reflexive strategies later in training. Reflexive strategy use was associated with increased activation in the putamen. Our results demonstrate a critical role for the reflexive corticostriatal learning system as a function of response strategy and proficiency during speech category learning. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

14 CFR 61.159 - Aeronautical experience: Airplane category rating.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Aeronautical experience: Airplane category... Transport Pilots § 61.159 Aeronautical experience: Airplane category rating. (a) Except as provided in... certificate with an airplane category and class rating must have at least 1,500 hours of total time as a pilot...

14 CFR 61.159 - Aeronautical experience: Airplane category rating.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Aeronautical experience: Airplane category... Transport Pilots § 61.159 Aeronautical experience: Airplane category rating. (a) Except as provided in... certificate with an airplane category and class rating must have at least 1,500 hours of total time as a pilot...

14 CFR 61.159 - Aeronautical experience: Airplane category rating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Aeronautical experience: Airplane category... Transport Pilots § 61.159 Aeronautical experience: Airplane category rating. (a) Except as provided in... certificate with an airplane category and class rating must have at least 1,500 hours of total time as a pilot...

14 CFR 61.159 - Aeronautical experience: Airplane category rating.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Aeronautical experience: Airplane category... Transport Pilots § 61.159 Aeronautical experience: Airplane category rating. (a) Except as provided in... certificate with an airplane category and class rating must have at least 1,500 hours of total time as a pilot...

14 CFR 61.159 - Aeronautical experience: Airplane category rating.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Aeronautical experience: Airplane category... Transport Pilots § 61.159 Aeronautical experience: Airplane category rating. (a) Except as provided in... certificate with an airplane category and class rating must have at least 1,500 hours of total time as a pilot...

Grammatical category dissociation in multilingual aphasia.

PubMed

Faroqi-Shah, Yasmeen; Waked, Arifi N

2010-03-01

Word retrieval deficits for specific grammatical categories, such as verbs versus nouns, occur as a consequence of brain damage. Such deficits are informative about the nature of lexical organization in the human brain. This study examined retrieval of grammatical categories across three languages in a trilingual person with aphasia who spoke Arabic, French, and English. In order to delineate the nature of word production difficulty, comprehension was tested, and a variety of concomitant lexical-semantic variables were analysed. The patient demonstrated a consistent noun-verb dissociation in picture naming and narrative speech, with severely impaired production of verbs across all three languages. The cross-linguistically similar noun-verb dissociation, coupled with little evidence of semantic impairment, suggests that (a) the patient has a true "nonsemantic" grammatical category specific deficit, and (b) lexical organization in multilingual speakers shares grammatical class information between languages. The findings of this study contribute to our understanding of the architecture of lexical organization in bilinguals.

On Anaphora and the Binding Principles in Categorial Grammar

NASA Astrophysics Data System (ADS)

Morrill, Glyn; Valentín, Oriol

In type logical categorial grammar the analysis of an expression is a resource-conscious proof. Anaphora represents a particular challenge to this approach in that the antecedent resource is multiplied in the semantics. This duplication, which corresponds logically to the structural rule of contraction, may be treated lexically or syntactically. Furthermore, anaphora is subject to constraints, which Chomsky (1981) formulated as Binding Principles A, B, and C. In this paper we consider English anaphora in categorial grammar including reference to the binding principles. We invoke displacement calculus, modal categorial calculus, categorial calculus with limited contraction, and entertain addition of negation as failure.

Increased experience amplifies the activation of task-irrelevant category representations.

PubMed

Wu, Rachel; Pruitt, Zoe; Zinszer, Benjamin D; Cheung, Olivia S

2017-02-01

Prior research has demonstrated the benefits (i.e., task-relevant attentional selection) and costs (i.e., task-irrelevant attentional capture) of prior knowledge on search for an individual target or multiple targets from a category. This study investigated whether the level of experience with particular categories predicts the degree of task-relevant and task-irrelevant activation of item and category representations. Adults with varying levels of dieting experience (measured via 3 subscales of Disinhibition, Restraint, Hunger; Stunkard & Messick, Journal of Psychosomatic Research, 29(1), 71-83, 1985) searched for targets defined as either a specific food item (e.g., carrots), or a category (i.e., any healthy or unhealthy food item). Apart from the target-present trials, in the target-absent "foil" trials, when searching for a specific item (e.g., carrots), irrelevant items from the target's category (e.g., squash) were presented. The ERP (N2pc) results revealed that the activation of task-relevant representations (measured via Exemplar and Category N2pc amplitudes) did not differ based on the degree of experience. Critically, however, increased dieting experience, as revealed by lower Disinhibition scores, predicted activation of task-irrelevant representations (i.e., attentional capture of foils from the target item category). Our results suggest that increased experience with particular categories encourages the rapid activation of category representations even when category information is task irrelevant, and that the N2pc in foil trials could potentially serve as an indication of experience level in future studies on categorization.

Category specific dysnomia after thalamic infarction: a case-control study.

PubMed

Levin, Netta; Ben-Hur, Tamir; Biran, Iftah; Wertman, Eli

2005-01-01

Category specific naming impairment was described mainly after cortical lesions. It is thought to result from a lesion in a specific network, reflecting the organization of our semantic knowledge. The deficit usually involves multiple semantic categories whose profile of naming deficit generally obeys the animate/inanimate dichotomy. Thalamic lesions cause general semantic naming deficit, and only rarely a category specific semantic deficit for very limited and highly specific categories. We performed a case-control study on a 56-year-old right-handed man who presented with language impairment following a left anterior thalamic infarction. His naming ability and semantic knowledge were evaluated in the visual, tactile and auditory modalities for stimuli from 11 different categories, and compared to that of five controls. In naming to visual stimuli the patient performed poorly (error rate>50%) in four categories: vegetables, toys, animals and body parts (average 70.31+/-15%). In each category there was a different dominating error type. He performed better in the other seven categories (tools, clothes, transportation, fruits, electric, furniture, kitchen utensils), averaging 14.28+/-9% errors. Further analysis revealed a dichotomy between naming in animate and inanimate categories in the visual and tactile modalities but not in response to auditory stimuli. Thus, a unique category specific profile of response and naming errors to visual and tactile, but not auditory stimuli was found after a left anterior thalamic infarction. This might reflect the role of the thalamus not only as a relay station but further as a central integrator of different stages of perceptual and semantic processing.

Attentional Bias in Human Category Learning: The Case of Deep Learning.

PubMed

Hanson, Catherine; Caglar, Leyla Roskan; Hanson, Stephen José

2018-01-01

Category learning performance is influenced by both the nature of the category's structure and the way category features are processed during learning. Shepard (1964, 1987) showed that stimuli can have structures with features that are statistically uncorrelated (separable) or statistically correlated (integral) within categories. Humans find it much easier to learn categories having separable features, especially when attention to only a subset of relevant features is required, and harder to learn categories having integral features, which require consideration of all of the available features and integration of all the relevant category features satisfying the category rule (Garner, 1974). In contrast to humans, a single hidden layer backpropagation (BP) neural network has been shown to learn both separable and integral categories equally easily, independent of the category rule (Kruschke, 1993). This "failure" to replicate human category performance appeared to be strong evidence that connectionist networks were incapable of modeling human attentional bias. We tested the presumed limitations of attentional bias in networks in two ways: (1) by having networks learn categories with exemplars that have high feature complexity in contrast to the low dimensional stimuli previously used, and (2) by investigating whether a Deep Learning (DL) network, which has demonstrated humanlike performance in many different kinds of tasks (language translation, autonomous driving, etc.), would display human-like attentional bias during category learning. We were able to show a number of interesting results. First, we replicated the failure of BP to differentially process integral and separable category structures when low dimensional stimuli are used (Garner, 1974; Kruschke, 1993). Second, we show that using the same low dimensional stimuli, Deep Learning (DL), unlike BP but similar to humans, learns separable category structures more quickly than integral category structures

Adjacent-Categories Mokken Models for Rater-Mediated Assessments

PubMed Central

Wind, Stefanie A.

2016-01-01

Molenaar extended Mokken’s original probabilistic-nonparametric scaling models for use with polytomous data. These polytomous extensions of Mokken’s original scaling procedure have facilitated the use of Mokken scale analysis as an approach to exploring fundamental measurement properties across a variety of domains in which polytomous ratings are used, including rater-mediated educational assessments. Because their underlying item step response functions (i.e., category response functions) are defined using cumulative probabilities, polytomous Mokken models can be classified as cumulative models based on the classifications of polytomous item response theory models proposed by several scholars. In order to permit a closer conceptual alignment with educational performance assessments, this study presents an adjacent-categories variation on the polytomous monotone homogeneity and double monotonicity models. Data from a large-scale rater-mediated writing assessment are used to illustrate the adjacent-categories approach, and results are compared with the original formulations. Major findings suggest that the adjacent-categories models provide additional diagnostic information related to individual raters’ use of rating scale categories that is not observed under the original formulation. Implications are discussed in terms of methods for evaluating rating quality. PMID:29795916

Category-dependent and category-independent goal-value codes in human ventromedial prefrontal cortex

PubMed Central

McNamee, Daniel; Rangel, Antonio; O’Doherty, John P

2013-01-01

To choose between manifestly distinct options, it is suggested that the brain assigns values to goals using a common currency. Although previous studies have reported activity in ventromedial prefrontal cortex (vmPFC) correlating with the value of different goal stimuli, it remains unclear whether such goal-value representations are independent of the associated stimulus categorization, as required by a common currency. Using multivoxel pattern analyses on functional magnetic resonance imaging (fMRI) data, we found a region of medial prefrontal cortex to contain a distributed goal-value code that is independent of stimulus category. More ventrally in the vmPFC, we found spatially distinct areas of the medial orbitofrontal cortex to contain unique category-dependent distributed value codes for food and consumer items. These results implicate the medial prefrontal cortex in the implementation of a common currency and suggest a ventral versus dorsal topographical organization of value signals in the vmPFC. PMID:23416449

Brain damage and semantic category dissociations: is the animals category easier for males?

PubMed

Scotti, Stefania; Laiacona, Marcella; Capitani, Erminio

2010-08-01

Semantic dissociations show that biological stimuli present a further dissociation between animals and plant life. Almost all cases of greater impairment of plant life knowledge were males, suggesting a higher male familiarity with animals possibly derived from different daily activities. To verify this hypothesis, we collected familiarity ratings for normal males and females, for 288 animals, subdivided according to whether they were hunted/fished, or were used as food. The overall familiarity was almost identical between males and females. Males were more familiar with hunted animals, but for them also food animals were more familiar. There was not a consistent effect of hunting/fishing independently of the food/not food classification. The claim that males are generally more proficient with animals knowledge because most hunters/fishers are males seems rather simplistic, and the familiarity structure of the animals category is more complex. An evolution-based account is suggested for the category by sex interaction.

40 CFR 98.200 - Definition of source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Magnesium Production § 98.200 Definition of source category. The magnesium production and processing source category consists of the following processes: (a) Any process in which magnesium metal is produced through smelting (including electrolytic smelting), refining...

40 CFR 98.200 - Definition of source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Magnesium Production § 98.200 Definition of source category. The magnesium production and processing source category consists of the following processes: (a) Any process in which magnesium metal is produced through smelting (including electrolytic smelting), refining...

40 CFR 98.200 - Definition of source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Magnesium Production § 98.200 Definition of source category. The magnesium production and processing source category consists of the following processes: (a) Any process in which magnesium metal is produced through smelting (including electrolytic smelting), refining...

40 CFR 98.200 - Definition of source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Magnesium Production § 98.200 Definition of source category. The magnesium production and processing source category consists of the following processes: (a) Any process in which magnesium metal is produced through smelting (including electrolytic smelting), refining...

Nuclear Fabrication Consortium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levesque, Stephen

2013-04-05

This report summarizes the activities undertaken by EWI while under contract from the Department of Energy (DOE) Office of Nuclear Energy (NE) for the management and operation of the Nuclear Fabrication Consortium (NFC). The NFC was established by EWI to independently develop, evaluate, and deploy fabrication approaches and data that support the re-establishment of the U.S. nuclear industry: ensuring that the supply chain will be competitive on a global stage, enabling more cost-effective and reliable nuclear power in a carbon constrained environment. The NFC provided a forum for member original equipment manufactures (OEM), fabricators, manufacturers, and materials suppliers to effectivelymore » engage with each other and rebuild the capacity of this supply chain by : Identifying and removing impediments to the implementation of new construction and fabrication techniques and approaches for nuclear equipment, including system components and nuclear plants. Providing and facilitating detailed scientific-based studies on new approaches and technologies that will have positive impacts on the cost of building of nuclear plants. Analyzing and disseminating information about future nuclear fabrication technologies and how they could impact the North American and the International Nuclear Marketplace. Facilitating dialog and initiate alignment among fabricators, owners, trade associations, and government agencies. Supporting industry in helping to create a larger qualified nuclear supplier network. Acting as an unbiased technology resource to evaluate, develop, and demonstrate new manufacturing technologies. Creating welder and inspector training programs to help enable the necessary workforce for the upcoming construction work. Serving as a focal point for technology, policy, and politically interested parties to share ideas and concepts associated with fabrication across the nuclear industry. The report the objectives and summaries of the Nuclear Fabrication

Category learning in the color-word contingency learning paradigm.

PubMed

Schmidt, James R; Augustinova, Maria; De Houwer, Jan

2018-04-01

In the typical color-word contingency learning paradigm, participants respond to the print color of words where each word is presented most often in one color. Learning is indicated by faster and more accurate responses when a word is presented in its usual color, relative to another color. To eliminate the possibility that this effect is driven exclusively by the familiarity of item-specific word-color pairings, we examine whether contingency learning effects can be observed also when colors are related to categories of words rather than to individual words. To this end, the reported experiments used three categories of words (animals, verbs, and professions) that were each predictive of one color. Importantly, each individual word was presented only once, thus eliminating individual color-word contingencies. Nevertheless, for the first time, a category-based contingency effect was observed, with faster and more accurate responses when a category item was presented in the color in which most of the other items of that category were presented. This finding helps to constrain episodic learning models and sets the stage for new research on category-based contingency learning.

Toward a dual-learning systems model of speech category learning

PubMed Central

Chandrasekaran, Bharath; Koslov, Seth R.; Maddox, W. T.

2014-01-01

More than two decades of work in vision posits the existence of dual-learning systems of category learning. The reflective system uses working memory to develop and test rules for classifying in an explicit fashion, while the reflexive system operates by implicitly associating perception with actions that lead to reinforcement. Dual-learning systems models hypothesize that in learning natural categories, learners initially use the reflective system and, with practice, transfer control to the reflexive system. The role of reflective and reflexive systems in auditory category learning and more specifically in speech category learning has not been systematically examined. In this article, we describe a neurobiologically constrained dual-learning systems theoretical framework that is currently being developed in speech category learning and review recent applications of this framework. Using behavioral and computational modeling approaches, we provide evidence that speech category learning is predominantly mediated by the reflexive learning system. In one application, we explore the effects of normal aging on non-speech and speech category learning. Prominently, we find a large age-related deficit in speech learning. The computational modeling suggests that older adults are less likely to transition from simple, reflective, unidimensional rules to more complex, reflexive, multi-dimensional rules. In a second application, we summarize a recent study examining auditory category learning in individuals with elevated depressive symptoms. We find a deficit in reflective-optimal and an enhancement in reflexive-optimal auditory category learning. Interestingly, individuals with elevated depressive symptoms also show an advantage in learning speech categories. We end with a brief summary and description of a number of future directions. PMID:25132827

Learning and transfer of category knowledge in an indirect categorization task.

PubMed

Helie, Sebastien; Ashby, F Gregory

2012-05-01

Knowledge representations acquired during category learning experiments are 'tuned' to the task goal. A useful paradigm to study category representations is indirect category learning. In the present article, we propose a new indirect categorization task called the "same"-"different" categorization task. The same-different categorization task is a regular same-different task, but the question asked to the participants is about the stimulus category membership instead of stimulus identity. Experiment 1 explores the possibility of indirectly learning rule-based and information-integration category structures using the new paradigm. The results suggest that there is little learning about the category structures resulting from an indirect categorization task unless the categories can be separated by a one-dimensional rule. Experiment 2 explores whether a category representation learned indirectly can be used in a direct classification task (and vice versa). The results suggest that previous categorical knowledge acquired during a direct classification task can be expressed in the same-different categorization task only when the categories can be separated by a rule that is easily verbalized. Implications of these results for categorization research are discussed.

Fabrication

NASA Technical Reports Server (NTRS)

Angel, Roger; Helms, Richard; Bilbro, Jim; Brown, Norman; Eng, Sverre; Hinman, Steve; Hull-Allen, Greg; Jacobs, Stephen; Keim, Robert; Ulmer, Melville

1992-01-01

What aspects of optical fabrication technology need to be developed so as to facilitate existing planned missions, or enable new ones? Throughout the submillimeter to UV wavelengths, the common goal is to push technology to the limits to make the largest possible apertures that are diffraction limited. At any one wavelength, the accuracy of the surface must be better than lambda/30 (rms error). The wavelength range is huge, covering four orders of magnitude from 1 mm to 100 nm. At the longer wavelengths, diffraction limited surfaces can be shaped with relatively crude techniques. The challenge in their fabrication is to make as large as possible a reflector, given the weight and volume constraints of the launch vehicle. The limited cargo diameter of the shuttle has led in the past to emphasis on deployable or erectable concepts such as the Large Deployable Reflector (LDR), which was studied by NASA for a submillimeter astrophysics mission. Replication techniques that can be used to produce light, low-cost reflecting panels are of great interest for this class of mission. At shorter wavelengths, in the optical and ultraviolet, optical fabrication will tax to the limit the most refined polishing methods. Methods of mechanical and thermal stabilization of the substrate will be severely stressed. In the thermal infrared, the need for large aperture is tempered by the even stronger need to control the telescope's thermal emission by cooled or cryogenic operation. Thus, the SIRTF mirror at 1 meter is not large and does not require unusually high accuracy, but the fabrication process must produce a mirror that is the right shape at a temperature of 4 K. Future large cooled mirrors will present more severe problems, especially if they must also be accurate enough to work at optical wavelengths. At the very shortest wavelengths accessible to reflecting optics, in the x-ray domain, the very low count fluxes of high energy photons place a premium on the collecting area. It is

Fabrication

NASA Astrophysics Data System (ADS)

Angel, Roger; Helms, Richard; Bilbro, Jim; Brown, Norman; Eng, Sverre; Hinman, Steve; Hull-Allen, Greg; Jacobs, Stephen; Keim, Robert; Ulmer, Melville

1992-08-01

What aspects of optical fabrication technology need to be developed so as to facilitate existing planned missions, or enable new ones? Throughout the submillimeter to UV wavelengths, the common goal is to push technology to the limits to make the largest possible apertures that are diffraction limited. At any one wavelength, the accuracy of the surface must be better than lambda/30 (rms error). The wavelength range is huge, covering four orders of magnitude from 1 mm to 100 nm. At the longer wavelengths, diffraction limited surfaces can be shaped with relatively crude techniques. The challenge in their fabrication is to make as large as possible a reflector, given the weight and volume constraints of the launch vehicle. The limited cargo diameter of the shuttle has led in the past to emphasis on deployable or erectable concepts such as the Large Deployable Reflector (LDR), which was studied by NASA for a submillimeter astrophysics mission. Replication techniques that can be used to produce light, low-cost reflecting panels are of great interest for this class of mission. At shorter wavelengths, in the optical and ultraviolet, optical fabrication will tax to the limit the most refined polishing methods. Methods of mechanical and thermal stabilization of the substrate will be severely stressed. In the thermal infrared, the need for large aperture is tempered by the even stronger need to control the telescope's thermal emission by cooled or cryogenic operation. Thus, the SIRTF mirror at 1 meter is not large and does not require unusually high accuracy, but the fabrication process must produce a mirror that is the right shape at a temperature of 4 K. Future large cooled mirrors will present more severe problems, especially if they must also be accurate enough to work at optical wavelengths. At the very shortest wavelengths accessible to reflecting optics, in the x-ray domain, the very low count fluxes of high energy photons place a premium on the collecting area. It is

40 CFR 98.70 - Definition of source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Ammonia Manufacturing § 98.70 Definition of source category. The ammonia manufacturing source category comprises the process units listed in paragraphs (a) and (b) of this section. (a) Ammonia manufacturing processes in which ammonia is manufactured from a fossil...

40 CFR 98.70 - Definition of source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Ammonia Manufacturing § 98.70 Definition of source category. The ammonia manufacturing source category comprises the process units listed in paragraphs (a) and (b) of this section. (a) Ammonia manufacturing processes in which ammonia is manufactured from a fossil...

40 CFR 98.70 - Definition of source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Ammonia Manufacturing § 98.70 Definition of source category. The ammonia manufacturing source category comprises the process units listed in paragraphs (a) and (b) of this section. (a) Ammonia manufacturing processes in which ammonia is manufactured from a fossil...

40 CFR 98.70 - Definition of source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Ammonia Manufacturing § 98.70 Definition of source category. The ammonia manufacturing source category comprises the process units listed in paragraphs (a) and (b) of this section. (a) Ammonia manufacturing processes in which ammonia is manufactured from a fossil...

40 CFR 98.70 - Definition of source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Ammonia Manufacturing § 98.70 Definition of source category. The ammonia manufacturing source category comprises the process units listed in paragraphs (a) and (b) of this section. (a) Ammonia manufacturing processes in which ammonia is manufactured from a fossil...

40 CFR 98.50 - Definition of source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Definition of source category. 98.50 Section 98.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Adipic Acid Production § 98.50 Definition of source category...

40 CFR 98.350 - Definition of source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Industrial Wastewater Treatment § 98.350 Definition of source category. (a) This source category consists of anaerobic processes used to treat industrial wastewater and industrial wastewater treatment sludge at facilities that perform the operations listed in this paragraph. (1...

40 CFR 98.350 - Definition of source category.

Code of Federal Regulations, 2012 CFR