Fault geometries illuminated from seismicity in central Taiwan: Implications for crustal scale structural boundaries in the northern Central Range

NASA Astrophysics Data System (ADS)

Gourley, Jonathan R.; Byrne, Timothy; Chan, Yu-Chang; Wu, Francis; Rau, Ruey-Juin

2007-12-01

Data sets of collapsed earthquake locations, earthquake focal mechanisms, GPS velocities and geologic data are integrated to constrain the geometry and kinematics of a crustal block within the accreted continental margin rocks of Taiwan's northeastern Central Range. This block is laterally extruding and exhuming towards the north-northeast. The block is bound on the west-southwest by the previously recognized Sanyi-Puli seismic zone and on the east by a vertical seismic structure that projects to the eastern mountain front of the Central Range. Focal mechanisms from the Broadband Array of Taiwan Seismicity (BATS) catalog consistently show west-side-up reverse displacements for this fault zone. A second vertical structure is recognized beneath the Slate Belt-Metamorphic Belt boundary as a post-Chi-Chi relaxation oblique normal fault. BATS focal mechanisms show east-side-up, normal displacements with a minor left-lateral component. The vertical and lateral extrusion of this crustal block may be driven by the current collision between the Philippine Sea Plate and the Puli basement high indenter on the Eurasian Plate and/or trench rollback along the Ryukyu subduction zone. In addition, the vertical extent of the two shear zones suggests that a basal décollement below the eastern Central Range is deeper than previously proposed and may extend below the brittle-ductile transition.

Evidence of spatial and temporal slip partitioning in the northern Central Nevada Seismic Belt from ground-based imaging of offset landforms

NASA Astrophysics Data System (ADS)

Gold, P. O.; Cowgill, E.; Kreylos, O.

2010-12-01

Measurements derived from high-resolution terrestrial LiDAR (t-Lidar) surveys of landforms displaced during the 16 December 1954 Mw 6.8 Dixie Valley earthquake in central Nevada confirm the absence of historical strike slip north of latitude 39.5°N. This conclusion has implications for the effect of stress changes on the spatial and temporal evolution of the central Nevada seismic belt. The Dixie Valley fault is a low-angle, east-dipping, range-bounding normal fault located in the central-northern reach of the central Nevada seismic belt (CNSB), a ~N-S trending group of historical ruptures that may represent a migration of northwest trending right-lateral Pacific-North American plate motion into central Nevada. Migration of a component of right slip eastward from the eastern California shear zone/Walker lane to the CNSB is supported by the presence of pronounced right-lateral motion observed in most of the CNSB earthquakes south of the Dixie Valley fault and by GPS data spanning the CNSB. Such eastward migration and northward propagation of right-slip into the CNSB predicts a component of lateral slip on the Dixie Valley fault. However, landforms offsets have previously been reported to indicate only purely normal slip in the 1954 Dixie Valley event. To check the direction of motion during the Dixie Valley earthquake using higher precision methods than previously employed, we collected t-LiDAR data to quantify displacements of two well-preserved debris flow chutes separated along strike by ~10 km and at locations where the local fault strike diverges by >10° from the regional strike. Our highest confidence measurements yield a horizontal slip vector azimuth of ~107° at both sites, orthogonal to the average regional fault strike of ~17°. Thus, we find no compelling evidence for regional lateral motion in our other measurements. This result indicates that continued northward propagation of right lateral slip from its diffuse termination at the northern end of the 1954 Fairview Peak event, 4 minutes before the Dixie Valley event, and the Rainbow Mountain-Stillwater events six months earlier, must be accommodated by some other mechanism. We see several options for the spatial and temporal evolution of right slip propagation into the northern CNSB. 1) Lateral motion may be accommodated to the east by faults opposite the Dixie Valley fault along the base of Clan Alpine range, or to the west by faults at the western base of the Stillwater range-diffuse faults to the SW and SE of the Dixie Valley fault that also ruptured in 1954 accommodated right slip and could represent a west and/or east migration of lateral motion; 2) right lateral motion may activate an as yet unrecognized fault within the Dixie Valley; or 3) the Dixie Valley fault may be reactivated with a greater component of lateral slip in response to changes in stress, a phenomena that has been recognized on the Borrego Fault in northern Mexico between the penultimate event and the recent 4 April 2010 El Mayor-Cucapah earthquake.

The history of late holocene surface-faulting earthquakes on the central segments of the Wasatch fault zone, Utah

USGS Publications Warehouse

Duross, Christopher; Personius, Stephen; Olig, Susan S; Crone, Anthony J.; Hylland, Michael D.; Lund, William R; Schwartz, David P.

2017-01-01

The Wasatch fault (WFZ)—Utah’s longest and most active normal fault—forms a prominent eastern boundary to the Basin and Range Province in northern Utah. To provide paleoseismic data for a Wasatch Front regional earthquake forecast, we synthesized paleoseismic data to define the timing and displacements of late Holocene surface-faulting earthquakes on the central five segments of the WFZ. Our analysis yields revised histories of large (M ~7) surface-faulting earthquakes on the segments, as well as estimates of earthquake recurrence and vertical slip rate. We constrain the timing of four to six earthquakes on each of the central segments, which together yields a history of at least 24 surface-faulting earthquakes since ~6 ka. Using earthquake data for each segment, inter-event recurrence intervals range from about 0.6 to 2.5 kyr, and have a mean of 1.2 kyr. Mean recurrence, based on closed seismic intervals, is ~1.1–1.3 kyr per segment, and when combined with mean vertical displacements per segment of 1.7–2.6 m, yield mean vertical slip rates of 1.3–2.0 mm/yr per segment. These data refine the late Holocene behavior of the central WFZ; however, a significant source of uncertainty is whether structural complexities that define the segments of the WFZ act as hard barriers to ruptures propagating along the fault. Thus, we evaluate fault rupture models including both single-segment and multi-segment ruptures, and define 3–17-km-wide spatial uncertainties in the segment boundaries. These alternative rupture models and segment-boundary zones honor the WFZ paleoseismic data, take into account the spatial and temporal limitations of paleoseismic data, and allow for complex ruptures such as partial-segment and spillover ruptures. Our data and analyses improve our understanding of the complexities in normal-faulting earthquake behavior and provide geological inputs for regional earthquake-probability and seismic hazard assessments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKee, E.H.

Ground water flow through the region south and west of Frenchman Flat, in the Ash Meadows subbasin of the Death Valley ground water flow system, is controlled mostly by the distribution of permeable and impermeable rocks. Geologic structures such as faults are instrumental in arranging the distribution of the aquifer and aquitard rock units. Most permeability is in fractures caused by faulting in carbonate rocks. Large faults are more likely to reach the potentiometric surface about 325 meters below the ground surface and are more likely to effect the flow path than small faults. Thus field work concentrated on identifyingmore » large faults, especially where they cut carbonate rocks. Small faults, however, may develop as much permeability as large faults. Faults that are penetrative and are part of an anastomosing fault zone are particularly important. The overall pattern of faults and joints at the ground surface in the Spotted and Specter Ranges is an indication of the fracture system at the depth of the water table. Most of the faults in these ranges are west-southwest-striking, high-angle faults, 100 to 3500 meters long, with 10 to 300 /meters of displacement. Many of them, such as those in the Spotted Range and Rock Valley are left-lateral strike-slip faults that are conjugate to the NW-striking right-lateral faults of the Las Vegas Valley shear zone. These faults control the ground water flow path, which runs west-southwest beneath the Spotted Range, Mercury Valley and the Specter Range. The Specter Range thrust is a significant geologic structure with respect to ground water flow. This regional thrust fault emplaces siliceous clastic strata into the north central and western parts of the Specter Range.« less

Late Oligocene to present contractional structure in and around the Susitna basin, Alaska—Geophysical evidence and geological implications

USGS Publications Warehouse

Saltus, Richard W.; Stanley, Richard G.; Haeussler, Peter J.; Jones, James V.; Potter, Christopher J.; Lewis, Kristen A.

2016-01-01

The Cenozoic Susitna basin lies within an enigmatic lowland surrounded by the Central Alaska Range, Western Alaska Range (including the Tordrillo Mountains), and Talkeetna Mountains in south-central Alaska. Some previous interpretations show normal faults as the defining structures of the basin (e.g., Kirschner, 1994). However, analysis of new and existing geophysical data shows predominantly (Late Oligocene to present) thrust and reverse fault geometries in the region, as previously proposed by Hackett (1978). A key example is the Beluga Mountain fault where a 50-mGal gravity gradient, caused by the density transition from the igneous bedrock of Beluga Mountain to the >4-km-thick Cenozoic sedimentary section of Susitna basin, spans a horizontal distance of ∼40 km and straddles the topographic front. The location and shape of the gravity gradient preclude a normal fault geometry; instead, it is best explained by a southwest-dipping thrust fault, with its leading edge located several kilometers to the northeast of the mountain front, concealed beneath the shallow glacial and fluvial cover deposits. Similar contractional fault relationships are observed for other basin-bounding and regional faults as well. Contractional structures are consistent with a regional shortening strain field inferred from differential offsets on the Denali and Castle Mountain right-lateral strike-slip fault systems.

Late Neogene and Active Tectonics along the Northern Margin of the Central Anatolian Plateau,TURKEY

NASA Astrophysics Data System (ADS)

Yildirim, C.; Schildgen, T. F.; Melnick, D.; Echtler, H. P.; Strecker, M. R.

2009-12-01

Margins of orogenic plateaus are conspicuous geomorphic provinces that archive tectonic and climatic variations related to surface uplift. Their growth is associated with spatial and temporal variations of mode and rate of tectonics and surface processes. Those processes can be strongly linked to the evolution of margins and plateaus thorough time. As one of the major morpho-tectonic provinces of Turkey, the Central Pontides (coinciding with the northern margin of the Central Anatolian Plateau (CAP)) display a remarkable topography and present valuable geologic and geomorphic indicators to identify active tectonics. Morpho-tectonic analysis, geological cross-sections, seismic profiles, and geodetic analysis reveal continuous deformation characterized by brittle faults from Late Miocene to recent across the northern margin of the CAP. In the Sinop Peninsula and offshore in the southern Black Sea, pervasive faulting and folding and uplift of Late Miocene to Quaternary marine deposits is related to active margin tectonics of the offshore southern Black Sea thrust and the onshore Balifaki and Erikli faults. In the Kastamonu-Boyabat sedimentary basin, the Late Miocene to Quaternary continental equivalents are strongly deformed by the Ekinveren Fault. This vergent inverse and thrust fault with overstepping en echelon segments deforms not only Quaternary travertines and conglomerates, but also patterns of the Pleistocene to Holocene drainage systems. In the southern Kastamonu-Boyabat basin, an antithetic thrust fault of the Ekinveren Fault system deformed also Quaternary fluviatile terrace deposits. Farther south, a dextral transpressive splay of the North Anatolian Fault (NAF) deforms pediment surfaces and forms the northern flank of the Ilgaz active mountain range. The Ilgaz Range rises up to 2587 m.a.s.l and is delimited by active segments of the NAF.The Central Pontides are located at the apex of northward convex arc of the NAF. Geodetic analysis indicate a deviation of the slip vectors and strain partitioning in the Central Pontides due to the large restraining bend geometry of the NAF. DEM analysis and field observations reveal that the Central Pontides integrate an active bivergent wedge, indicating out-of sequence thrusting and topographical asymmetry, with a gentle pro-wedge northern slope and a steep retro-wedge southern slopes, and regional surface tilting from south to north. Uplifted presumably Late Pleistocene to Holocene marine terraces 4 to 40 m.a.s.l. along the coast and well developed pediment and fill and strath terrace surfaces ranging from 10 to 300 m above along the Gokirmak and Kizilirmak rivers will provide chronological constraints on the uplift and incision rates of the study area.

Net dextral slip, Neogene San Gregorio–Hosgri fault zone, coastal California: Geologic evidence and tectonic implications

USGS Publications Warehouse

Dickinson, William R.; Ducea, M.; Rosenberg, Lewis I.; Greene, H. Gary; Graham, Stephan A.; Clark, Joseph C.; Weber, Gerald E.; Kidder, Steven; Ernst, W. Gary; Brabb, Earl E.

2005-01-01

Reinterpretation of onshore and offshore geologic mapping, examination of a key offshore well core, and revision of cross-fault ties indicate Neogene dextral strike slip of 156 ± 4 km along the San Gregorio–Hosgri fault zone, a major strand of the San Andreas transform system in coastal California. Delineating the full course of the fault, defining net slip across it, and showing its relationship to other major tectonic features of central California helps clarify the evolution of the San Andreas system.San Gregorio–Hosgri slip rates over time are not well constrained, but were greater than at present during early phases of strike slip following fault initiation in late Miocene time. Strike slip took place southward along the California coast from the western fl ank of the San Francisco Peninsula to the Hosgri fault in the offshore Santa Maria basin without significant reduction by transfer of strike slip into the central California Coast Ranges. Onshore coastal segments of the San Gregorio–Hosgri fault include the Seal Cove and San Gregorio faults on the San Francisco Peninsula, and the Sur and San Simeon fault zones along the flank of the Santa Lucia Range.Key cross-fault ties include porphyritic granodiorite and overlying Eocene strata exposed at Point Reyes and at Point Lobos, the Nacimiento fault contact between Salinian basement rocks and the Franciscan Complex offshore within the outer Santa Cruz basin and near Esalen on the flank of the Santa Lucia Range, Upper Cretaceous (Campanian) turbidites of the Pigeon Point Formation on the San Francisco Peninsula and the Atascadero Formation in the southern Santa Lucia Range, assemblages of Franciscan rocks exposed at Point Sur and at Point San Luis, and a lithic assemblage of Mesozoic rocks and their Tertiary cover exposed near Point San Simeon and at Point Sal, as restored for intrabasinal deformation within the onshore Santa Maria basin.Slivering of the Salinian block by San Gregorio–Hosgri displacements elongated its northern end and offset its western margin delineated by the older Nacimiento fault, a sinistral strike-slip fault of latest Cretaceous to Paleocene age. North of its juncture with the San Andreas fault, dextral slip along the San Gregorio–Hosgri fault augments net San Andreas displacement. Alternate restorations of the Gualala block imply that nearly half the net San Gregorio–Hosgri slip was accommodated along the offshore Gualala fault strand lying west of the Gualala block, which is bounded on the east by the current master trace of the San Andreas fault. With San Andreas and San Gregorio–Hosgri slip restored, there remains an unresolved proto–San Andreas mismatch of ∼100 km between the offset northern end of the Salinian block and the southern end of the Sierran-Tehachapi block.On the south, San Gregorio–Hosgri strike slip is transposed into crustal shortening associated with vertical-axis tectonic rotation of fault-bounded crustal panels that form the western Transverse Ranges, and with kinematically linked deformation within the adjacent Santa Maria basin. The San Gregorio–Hosgri fault serves as the principal link between transrotation in the western Transverse Ranges and strike slip within the San Andreas transform system of central California.

Structural framework of a major intracontinental orogenic termination zone: The easternmost Tien Shan, China

USGS Publications Warehouse

Cunningham, D.; Owen, L.A.; Snee, L.W.; Li, Ji

2003-01-01

The Barkol Tagh and Karlik Tagh ranges of the easternmost Tien Shan are a natural laboratory for studying the fault architecture of an active termination zone of a major intracontinental mountain range. Barkol and Karlik Tagh and lesser ranges to the north are bounded by active thrust faults that locally deform Quaternary sediments. Major thrusts in Karlik Tagh connect along strike to the east with the left-lateral Gobi-Tien Shan Fault System in SW Mongolia. From a Mongolian perspective. Karlik Tagh represents a large restraining bend for this regional strike-slip fault system, and the entire system of thrusts and strike-slip faults in the Karlik Tagh region defines a horsetail splay fault geometry. Regionally, there appears to be a kinematic transition from thrust-dominated deformation in the central Tien Shan to left-lateral transpressional deformation in the easternmost Tien Shan. This transition correlates with a general eastward decrease in mountain belt width and average elevation and a change in the angular relationship between the NNE-directed maximum horizontal stress in the region and the pre-existing basement structural grain, which is northwesterly in the central Tien Shan (orthogonal to SHmax) but more east-west in the eastern Tien Shan (acute angular relationship with SHmax . Ar-Ar ages indicate that major range-bounding thrusts in Barkol and Karlik Tagh are latest Permian-Triassic ductile thrust zones that underwent brittle reactivation in the Late Cenozoic. It is estimated that the modern mountain ranges of the extreme easternmost Tien Shan could have been constructed by only 10-15 km of Late Cenozoic horizontal shortening.

Fault architecture and deformation processes within poorly lithified rift sediments, Central Greece

NASA Astrophysics Data System (ADS)

Loveless, Sian; Bense, Victor; Turner, Jenni

2011-11-01

Deformation mechanisms and resultant fault architecture are primary controls on the permeability of faults in poorly lithified sediments. We characterise fault architecture using outcrop studies, hand samples, thin sections and grain-size data from a minor (1-10 m displacement) normal-fault array exposed within Gulf of Corinth rift sediments, Central Greece. These faults are dominated by mixed zones with poorly developed fault cores and damage zones. In poorly lithified sediment deformation is distributed across the mixed zone as beds are entrained and smeared. We find particulate flow aided by limited distributed cataclasis to be the primary deformation mechanism. Deformation may be localised in more competent sediments. Stratigraphic variations in sediment competency, and the subsequent alternating distributed and localised strain causes complexities within the mixed zone such as undeformed blocks or lenses of cohesive sediment, or asperities at the mixed zone/protolith boundary. Fault tip bifurcation and asperity removal are important processes in the evolution of these fault zones. Our results indicate that fault zone architecture and thus permeability is controlled by a range of factors including lithology, stratigraphy, cementation history and fault evolution, and that minor faults in poorly lithified sediment may significantly impact subsurface fluid flow.

Late Cenozoic thrusting of major faults along the central segment of Longmen Shan, eastern Tibet: Evidence from low-temperature thermochronology

NASA Astrophysics Data System (ADS)

Tan, Xi-Bin; Xu, Xi-Wei; Lee, Yuan-Hsi; Lu, Ren-Qi; Liu, Yiduo; Xu, Chong; Li, Kang; Yu, Gui-Hua; Kang, Wen-Jun

2017-08-01

The Cenozoic orogenic process of the Longmen Shan (LMS) and the kinematics of major faults along the LMS are crucial for understanding the growth history and mechanism of the eastern Tibetan Plateau. Three major faults, from west to east, are present in the central segment of the LMS: the Wenchuan-Maoxian Fault (WMF), the Beichuan-Yingxiu Fault (BYF), and the Jiangyou-Guanxian Fault (JGF). Previous researchers have placed great impetus on the Pengguan Massif, between the WMF and BYF. However, limited low-temperature thermochronology data coverage in other areas prevents us from fully delineating the tectonic history of the LMS. In this study, we collect 22 samples from vertical profiles in the Xuelongbao Massif and the range frontal area located at the hanging walls of the WMF and JGF respectively, and conduct apatite and zircon fission track analyses. New fission track data reveal that the Xuelongbao Massif has been undergoing rapid exhumation with an average rate of 0.7-0.9 mm/yr since 11 Ma, and the range frontal area began rapid exhumation at 7.5 Ma with total exhumation of 2.5-4.5 km. The exhumation histories indicate that the three major faults (WMF, BYF and JGF) in the central LMS are all reverse faults, and show a basinward in-sequence propagation from middle Miocene to present-day. Such a pattern further implies that upper crustal shortening is the primary driver for the LMS' uplift during the Late Cenozoic. Nevertheless, middle-lower crustal deformation is difficult to be constrained by the exhumation histories, and its contribution to LMS' uplift cannot be ruled out.

Denali fault slip rates and Holocene-late Pleistocene kinematics of central Alaska

USGS Publications Warehouse

Matmon, A.; Schwartz, D.P.; Haeussler, Peter J.; Finkel, R.; Lienkaemper, J.J.; Stenner, Heidi D.; Dawson, T.E.

2006-01-01

The Denali fault is the principal intracontinental strike-slip fault accommodating deformation of interior Alaska associated with the Yakutat plate convergence. We obtained the first quantitative late Pleistocene-Holocene slip rates on the Denali fault system from dating offset geomorphic features. Analysis of cosmogenic 10Be concentrations in boulders (n = 27) and sediment (n = 13) collected at seven sites, offset 25-170 m by the Denali and Totschunda faults, gives average ages that range from 2.4 ± 0.3 ka to 17.0 ± 1.8 ka. These offsets and ages yield late Pleistocene-Holocene average slip rates of 9.4 ± 1.6, 12.1 ± 1.7, and 8.4 ± 2.2 mm/yr-1 along the western, central, and eastern Denali fault, respectively, and 6.0 ± 1.2 mm/yr-1 along the Totschunda fault. Our results suggest a westward decrease in the mean Pleistocene-Holocene slip rate. This westward decrease likely results from partitioning of slip from the Denali fault system to thrust faults to the north and west. 2006 Geological Society of America.

Geodetic Measurement of Deformation East of the San Andreas Fault in Central California

NASA Technical Reports Server (NTRS)

Sauber, Jeanne M.; Lisowski, Michael; Solomon, Sean C.

1988-01-01

Triangulation and trilateration data from two geodetic networks located between the western edge of the Great Valley and the San Andreas fault have been used to calculate shear strain rates in the Diablo Range and to estimate the slip rate along the Calaveras and Paicines faults in Central California. Within the Diablo Range the average shear strain rate was determined for the time period between 1962 and 1982 to be 0.15 + or - 0.08 microrad/yr, with the orientation of the most compressive strain at N 16 deg E + or - 14 deg. The orientation of the principal compressive strain predicted from the azimuth of the major structures in the region is N 25 deg E. It is inferred that the measured strain is due to compression across the folds of this area: the average shear straining corresponds to a relative shortening rate of 4.5 + or - 2.4 mm/yr. From an examination of wellbore breakout orientations and the azimuths of P-axes from earthquake focal mechanisms the inferred orientation of maximum compressive stress was found to be similar to the direction of maximum compressive strain implied by the trend of local fold structures. Results do not support the hypothesis of uniform fault-normal compression within the Coast Ranges. From trilateration measurements made between 1972 and 1987 on lines that are within 10 km of the San Andreas fault, a slip rate of 10 to 12 mm/yr was calculated for the Calaveras-Paicines fault south of Hollister. The slip rate of the Paicines fault decreases to 4 mm/yr near Bitter.

Paleomagnetism of the Oligocene Kalamazoo Tuff: implications for middle Tertiary extension in east central Nevada

USGS Publications Warehouse

Hagstrum, J.T.; Gans, P.B.

1989-01-01

The Oligocene Kalamazoo Tuff (???35 Ma) was sampled for paleomagnetic analysis across a 100-km-wide zone of highly extended crust in east central Nevada to estimate between-site vertical axis rotations and thus the relative importance of strike-slip faulting to the mechanism of extension. The tilt-corrected data, with sources of error reduced or eliminated, exhibit a 28?? ?? 12?? clockwise rotation of the Schell Creek Range relative to the Kern Mountains region. This rotation implies differential extension accommodated by strike-slip faulting or N-S shortening. The paleomagnetic results also suggest that large changes in strike of layered units near faults with presumed strike-slip movement need not be the result of oroclinal bending, but could result from superimposed sets of orthogonal normal faults. -from Authors

Late Cretaceous stratigraphy, deformation and intrusion in the Madison Range of southwestern Montana ( USA).

USGS Publications Warehouse

Tysdal, R.G.; Marvin, R.F.; Dewitt, E.

1986-01-01

Dating of orogenic rock units in the central part of the Madison Range shows that Laramide deformation was virtually completed by the end of the Cretaceous. Early Campanian K-Ar dates of about 79 m.y. were obtained from welded tuffs in the basal part of the Livingston Formation, a volcanic and volcaniclastic assemblage that is conformable with underlying Cretaceous clastic rocks and with the overlying Sphinx Conglomerate. The Sphinx and the Livingston were deformed by the Hilgard fault system which extends along the western side of the southern two-thirds of the range. This north-trending fault system represents the culmination of Laramide shortening within the range. Dating of hornblende indicates an approximate date of 68-69 m.y. B.P. for emplacement of the igneous suite. The dacite postdates movement along faults of the Hilgard fault system, and postdates the synorogenic Sphinx Conglomerate. -from Authors

Geologic strip map along the Hines Creek Fault showing evidence for Cenozoic displacement in the western Mount Hayes and northeastern Healy quadrangles, eastern Alaska Range, Alaska

USGS Publications Warehouse

Nokleberg, Warren J.; Aleinikoff, John N.; Bundtzen, Thomas K.; Hanshaw, Maiana N.

2013-01-01

Geologic mapping of the Hines Creek Fault and the adjacent Trident Glacier and McGinnis Glacier Faults to the north in the eastern Alaska Range, Alaska, reveals that these faults were active during the Cenozoic. Previously, the Hines Creek Fault, which is considered to be part of the strike-slip Denali Fault system (Ridgway and others, 2002; Nokleberg and Richter, 2007), was interpreted to have been welded shut during the intrusion of the Upper Cretaceous Buchanan Creek pluton (Wahrhaftig and others, 1975; Gilbert, 1977; Sherwood and Craddock, 1979; Csejtey and others, 1992). Our geologic mapping along the west- to west-northwest-striking Hines Creek Fault in the northeastern Healy quadrangle and central to northwestern Mount Hayes quadrangle reveals that (1) the Buchanan Creek pluton is truncated by the Hines Creek Fault and (2) a tectonic collage of fault-bounded slices of various granitic plutons, metagabbro, metabasalt, and sedimentary rock of the Pingston terrane occurs south of the Hines Creek Fault.

Frictional properties of saponite-rich gouge from a serpentinite-bearing fault zone along the Gokasho-Arashima Tectonic Line, central Japan

USGS Publications Warehouse

Sone, Hiroki; Shimamoto, Toshihiko; Moore, Diane E.

2012-01-01

We studied a serpentinite-bearing fault zone in Gokasho-Arashima Tectonic Line, Mie Prefecture, central Japan, characterizing its internal structures, mineral assemblage, permeability, and frictional properties. The fault core situated between the serpentinite breccia and the adjacent sedimentary rocks is characterized by a zone locally altered to saponite. The clayey gouge layer separates fault rocks of serpentinite origin containing talc and tremolite from fault rocks of sedimentary origin containing chlorite but no quartz. The minerals that formed within the fault are the products of metasomatic reaction between the serpentinite and the siliceous rocks. Permeability measurements show that serpentinite breccia and fault gouge have permeability of 10−14–10−17 m2 and 10−15–10−18 m2, respectively, at 5–120 MPa confining pressure. Frictional coefficient of the saponite-rich clayey fault gouge ranged between 0.20 and 0.35 under room-dry condition, but was reduced to 0.06–0.12 when saturated with water. The velocity dependence of friction was strongly positive, mostly ranging between 0.005 and 0.006 in terms of a–b values. The governing friction law is not constrained yet, but we find that the saponite-rich gouge possesses an evolutional behavior in the opposite direction to that suggested by the rate and state friction law, in addition to its direct velocity dependence.

Gently dipping normal faults identified with Space Shuttle radar topography data in central Sulawesi, Indonesia, and some implications for fault mechanics

USGS Publications Warehouse

Spencer, J.E.

2011-01-01

Space-shuttle radar topography data from central Sulawesi, Indonesia, reveal two corrugated, domal landforms, covering hundreds to thousands of square kilometers, that are bounded to the north by an abrupt transition to typical hilly to mountainous topography. These domal landforms are readily interpreted as metamorphic core complexes, an interpretation consistent with a single previous field study, and the abrupt northward transition in topographic style is interpreted as marking the trace of two extensional detachment faults that are active or were recently active. Fault dip, as determined by the slope of exhumed fault footwalls, ranges from 4?? to 18??. Application of critical-taper theory to fault dip and hanging-wall surface slope, and to similar data from several other active or recently active core complexes, suggests a theoretical limit of three degrees for detachment-fault dip. This result appears to conflict with the dearth of seismological evidence for slip on faults dipping less than ~. 30??. The convex-upward form of the gently dipping fault footwalls, however, allows for greater fault dip at depths of earthquake initiation and dominant energy release. Thus, there may be no conflict between seismological and mapping studies for this class of faults. ?? 2011 Elsevier B.V.

Paleomagnetic, structural, and seismological evidence for oblique-slip deformation in fault-related folds in the Rocky Mountain Foreland, Colorado Plateau, and central Coast Ranges

NASA Astrophysics Data System (ADS)

Tetreault, Joya Liana

The two geologic questions I address in this research are: do fault-related folds accommodate oblique-slip shortening, and how is oblique-slip deformation absorbed within the folded strata? If the strata is deforming as a strike-slip shear zone, then we should be able to observe material rotations produced by strike-slip shear by measuring paleomagnetic vertical-axis rotations. I have approached these problems by applying paleomagnetic vertical-axis rotations, minor fault analyses, and focal mechanism strain inversions to identify evidence of strike-slip shear and to quantify oblique-slip deformation within fault-related folds in the Rocky Mountain Foreland, Colorado Plateau, and the central Coast Ranges. Clockwise paleomagnetic vertical-axis rotations and compressive paleostress rotations of 15-40º in the forelimb of the Grayback Monocline, northeastern Front Range Colorado, indicate that this Laramide fold is absorbing right-lateral shear from a N90E regional shortening direction. This work shows that paleomagnetic vertical-axis rotations in folded strata can be used to identify strike-slip motion on an underlying fault, and that oblique-slip deformation is localized in the forelimb of the fold. I applied the same paleomagnetic methods to identify oblique-slip on the underlying faults of the Nacimiento, East Kaibab, San Rafael, and Grand Hogback monoclines of the Colorado Plateau. The absence of paleomagnetic rotations and structural evidence for small displacements at the Nacimiento and East Kaibab monoclines indicate minor (<1km) right-lateral slip is being accommodated in these folds. Paleomagnetic vertical-axis rotations are found in the forelimbs of the San Rafael and Grand Hogback monoclines, yielding strike-slip displacements of ˜5km within these two folds. These results are consistent with a northeast Laramide compressive stress direction. In the Coalinga anticline, central Coast Ranges, California, clockwise paleomagnetic rotations and an 8º counterclockwise deflection of the maximum shortening direction (derived from focal mechanisms strain inversions of the upper 7km) are compatible with right-lateral shear. The maximum shortening direction in the area of the mainshock rupture is fold-normal, indicating that strike-slip displacement is confined to the main fault plane and not distributed to the hanging wall. The San Andreas Fault is therefore partitioning a small amount of strike-slip to the Coalinga anticline.

The Surface Displacement Field of the November 8, 1997, Mw7.6 Manyi (Tibet) Earthquake Observed with ERS InSAR Data

NASA Technical Reports Server (NTRS)

Peltzer, G.; Crampe, F.

1998-01-01

ERS2 radar data acquired before and after the Mw7.6, Manyi (Tibet) earthquake of November 8, 1997, provide geodetic information about the surface displacement produced by the earthquake in two ways. (1) The sub-pixel geometric adjustment of the before and after images provides a two dimensional offset field with a resolution of approx, 1m in both the range (radar line of sight) and azimuth (satellite track) directions. Comparison of offsets in azimuth and range indicates that the displacement along the fault is essentially strike-slip and in a left-lateral sense. The offset map reveals a relatively smooth and straight, N78E surface rupture that exceeds 150 km in length, consistent with the EW plane of the Harvard CMT solution. The rupture follows the trace of a quaternary fault visible on satellite imagery (Tapponnier and Molnar, 1978; Wan Der Woerd, pers. comm.). (2) Interferometric processing of the SAR data provides a range displacement map with a precision of a few millimeters. The slip distribution along the rupture reconstructed from the range change map is a bell-shaped curve in the 100-km long central section of the fault with smaller, local maxima near both ends. The curve shows that the fault slip exceeds 2.2 m in range, or 6.2 in strike-slip, along a 30-km long section of the fault and remains above 1 m in range, approx. 3 m strike-slip, along most of its length. Preliminary forward modeling of the central section of the rupture, assuming a uniform slip distribution with depth, indicates that the slip occur-red essentially between 0 and the depth of 10 km, consistent with a relatively shallow event (Velasco et al., 1998).

An update of Quaternary faults of central and eastern Oregon

USGS Publications Warehouse

Weldon, Ray J.; Fletcher, D.K.; Weldon, E.M.; Scharer, K.M.; McCrory, P.A.

2002-01-01

This is the online version of a CD-ROM publication. We have updated the eastern portion of our previous active fault map of Oregon (Pezzopane, Nakata, and Weldon, 1992) as a contribution to the larger USGS effort to produce digital maps of active faults in the Pacific Northwest region. The 1992 fault map has seen wide distribution and has been reproduced in essentially all subsequent compilations of active faults of Oregon. The new map provides a substantial update of known active or suspected active faults east of the Cascades. Improvements in the new map include (1) many newly recognized active faults, (2) a linked ArcInfo map and reference database, (3) more precise locations for previously recognized faults on shaded relief quadrangles generated from USGS 30-m digital elevations models (DEM), (4) more uniform coverage resulting in more consistent grouping of the ages of active faults, and (5) a new category of 'possibly' active faults that share characteristics with known active faults, but have not been studied adequately to assess their activity. The distribution of active faults has not changed substantially from the original Pezzopane, Nakata and Weldon map. Most faults occur in the south-central Basin and Range tectonic province that is located in the backarc portion of the Cascadia subduction margin. These faults occur in zones consisting of numerous short faults with similar rates, ages, and styles of movement. Many active faults strongly correlate with the most active volcanic centers of Oregon, including Newberry Craters and Crater Lake.

Mapping tectonic and anthropogenic processes in central California using satellite and airborne InSAR

NASA Astrophysics Data System (ADS)

Liu, Z.; Lundgren, P.; Liang, C.; Farr, T. G.; Fielding, E. J.

2017-12-01

The improved spatiotemporal resolution of surface deformation from recent satellite and airborne InSAR measurements provides a great opportunity to improve our understanding of both tectonic and non-tectonic processes. In central California the primary plate boundary fault system (San Andreas fault) lies adjacent to the San Joaquin Valley (SJV), a vast structural trough that accounts for about one-sixth of the United Sates' irrigated land and one-fifth of its extracted groundwater. The central San Andreas fault (CSAF) displays a range of fault slip behavior with creeping in its central segment that decreases towards its northwest and southeast ends, where it transitions to being fully locked. Despite much progress, many questions regarding fault and anthropogenic processes in the region still remain. In this study, we combine satellite InSAR and NASA airborne UAVSAR data to image fault and anthropogenic deformation. The UAVSAR data cover fault perpendicular swaths imaged from opposing look directions and fault parallel swaths since 2009. The much finer spatial resolution and optimized viewing geometry provide important constraints on near fault deformation and fault slip at very shallow depth. We performed a synoptic InSAR time series analysis using Sentinel-1, ALOS, and UAVSAR interferograms. We estimate azimuth mis-registration between single look complex (SLC) images of Sentinel-1 in a stack sense to achieve accurate azimuth co-registration between SLC images for low coherence and/or long interval interferometric pairs. We show that it is important to correct large-scale ionosphere features in ALOS-2 ScanSAR data for accurate deformation measurements. Joint analysis of UAVSAR and ALOS interferometry measurements show clear variability in deformation along the fault strike, suggesting variable fault creep and locking at depth and along strike. In addition to fault creep, the L-band ALOS, and especially ALOS-2 ScanSAR interferometry, show large-scale ground subsidence in the SJV due to over-exploitation of groundwater. InSAR time series are compared to GPS and well-water hydraulic head in-situ time series to understand water storage processes and mass loading changes. We present model results to assess the influence of anthropogenic processes on surface deformation and fault mechanics.

Variable modes of rifting in the eastern Basin and Range, USA from on-fault geological evidence

NASA Astrophysics Data System (ADS)

Stahl, T.; Niemi, N. A.

2017-12-01

Continental rifts are often divided along their axes into magmatic (or magma-assisted) and amagmatic (or magma-poor) segments. Less is known about magmatic versus non-magmatic extension across `wide' continental rift margins like the Basin and Range province of the USA. Paleoseismic trench investigations, Quaternary geochronology (10Be and 3He exposure-age, luminescence, and 40Ar/39Ar dating), and high-resolution topographic surveys (terrestrial laser scanning and UAV photogrammetry) were used to assess the timing and spatial variability of faulting at the Basin and Range-Colorado Plateau transition zone in central Utah. Results show that while the majority of strain is accommodated by a single, range- and province-bounding fault (the Wasatch fault zone, WFZ, slip rate of c. 3-4 mm yr-1), a transition to magma-assisted rifting occurs near the WFZ southern termination marked by a diffuse zone of faults associated with Pliocene to Holocene volcanism. Paleoseismic analysis of faults within and adjacent to this zone reveal recent (<18 ka) surface-ruptures on these faults. A single event displacement of 10-15 m for the Tabernacle fault at c. 15-18 ka (3He exposure-age) and large fault displacement gradients imply that slip was coeval with lava emplacement and that the faults in this region are linked, at least in part, to dike injection in the uppermost crust rather than slip at seismogenic depths. These results have implications for the controversial nature of regional seismic hazard and the structural evolution of the eastern Basin and Range.

Plio-Pleistocene North-South and East-West Extension at the Southern Margin of the Tibetan Plateau

NASA Astrophysics Data System (ADS)

McDermott, Jeni Amber

The tectonic significance of the physiographic transition from the low-relief Tibetan plateau to the high peaks, rugged topography and deep gorges of the Himalaya is the source of much controversy. Some workers have suggested the transition may be structurally controlled (e.g. Hodges et al., 2001), and indeed, the sharp change in geomorphic character across the transition strongly suggests differential uplift between the Himalayan realm and the southernmost Tibetan Plateau. Most Himalayan researchers credit the South Tibetan fault system (STFS), a family of predominantly east-west trending, low-angle normal faults with a known trace of over 2,000 km along the Himalayan crest (e.g. Burchfiel et al., 1992), with defining the southern margin of the Tibetan Plateau in the Early Miocene. Inasmuch as most mapped strands of the STFS have not been active since the Middle Miocene (e.g., Searle & Godin, 2003), modern-day control of the physiographic transition by this fault system seems unlikely. However, several workers have documented Quaternary slip on east-west striking, N-directed extensional faults, of a similar structural nature but typically at a different tectonostratigraphic level than the principal STFS strand, in several locations across the range (Nakata, 1989; Wu et al., 1998; Hurtado et al., 2001). In order to explore the nature of the physiographic transition and determine its relationship to potential Quaternary faulting, I examined three field sites: the Kali Gandaki valley in central Nepal (˜28°39'54"N; 83°35'06"E), the Nyalam region of south-central Tibet (28°03'23.3"N, 86°03'54.08"E), and the Ama Drime Range in southernmost Tibet (87º15'-87º50'E; 27º45'-28º30'N). Research in each of these areas yielded evidence of young faulting on structures with normal-sense displacement in various forms: the structural truncation of lithostratigraphic units, distinctive fault scarps, or abrupt changes in bedrock cooling age patterns. These structures are accompanied by geomorphic changes implying structural control, particularly sharp knickpoints in rivers that drain from the Tibetan Plateau, across the range crest, and down through the southern flank of the Himalaya. Collectively, my structural, geomorphic, and thermochronometric studies confirm the existence of extensional structures near the physiographic transition that have been active more recently than 1.5 Ma in central Nepal, and over the last 3.5 Ma in south-central Tibet. The structural history of the Ama Drime Range is complex and new thermochronologic data suggest multiple phases of E-W extension from the Middle Miocene to the Holocene. Mapping in the accessible portions of the range did not yield evidence for young N-S extension, although my observations do not preclude such deformation on structures south of the study area. In contrast, the two other study areas yielded direct evidence that Quaternary faulting may be controlling the position and nature of the physiographic transition across the central Tibetan Plateau-Himalaya orogenic system.

Relationship between displacement and gravity change of Uemachi faults and surrounding faults of Osaka basin, Southwest Japan

NASA Astrophysics Data System (ADS)

Inoue, N.; Kitada, N.; Kusumoto, S.; Itoh, Y.; Takemura, K.

2011-12-01

The Osaka basin surrounded by the Rokko and Ikoma Ranges is one of the typical Quaternary sedimentary basins in Japan. The Osaka basin has been filled by the Pleistocene Osaka group and the later sediments. Several large cities and metropolitan areas, such as Osaka and Kobe are located in the Osaka basin. The basin is surrounded by E-W trending strike slip faults and N-S trending reverse faults. The N-S trending 42-km-long Uemachi faults traverse in the central part of the Osaka city. The Uemachi faults have been investigated for countermeasures against earthquake disaster. It is important to reveal the detailed fault parameters, such as length, dip and recurrence interval, so on for strong ground motion simulation and disaster prevention. For strong ground motion simulation, the fault model of the Uemachi faults consist of the two parts, the north and south parts, because of the no basement displacement in the central part of the faults. The Ministry of Education, Culture, Sports, Science and Technology started the project to survey of the Uemachi faults. The Disaster Prevention Institute of Kyoto University is carried out various surveys from 2009 to 2012 for 3 years. The result of the last year revealed the higher fault activity of the branch fault than main faults in the central part (see poster of "Subsurface Flexure of Uemachi Fault, Japan" by Kitada et al., in this meeting). Kusumoto et al. (2001) reported that surrounding faults enable to form the similar basement relief without the Uemachi faults model based on a dislocation model. We performed various parameter studies for dislocation model and gravity changes based on simplified faults model, which were designed based on the distribution of the real faults. The model was consisted 7 faults including the Uemachi faults. The dislocation and gravity change were calculated based on the Okada et al. (1985) and Okubo et al. (1993) respectively. The results show the similar basement displacement pattern to the Kusumoto et al. (2001) and no characteristic gravity change pattern. The Quantitative estimation is further problem.

Two-dimensional seismic image of the San Andreas Fault in the Northern Gabilan Range, central California: Evidence for fluids in the fault zone

USGS Publications Warehouse

Thurber, C.; Roecker, S.; Ellsworth, W.; Chen, Y.; Lutter, W.; Sessions, R.

1997-01-01

A joint inversion for two-dimensional P-wave velocity (Vp), P-to-S velocity ratio (Vp/Vs), and earthquake locations along the San Andreas fault (SAF) in central California reveals a complex relationship among seismicity, fault zone structure, and the surface fault trace. A zone of low Vp and high Vp/Vs lies beneath the SAF surface trace (SAFST), extending to a depth of about 6 km. Most of the seismic activity along the SAF occurs at depths of 3 to 7 km in a southwest-dipping zone that roughly intersects the SAFST, and lies near the southwest edge of the low Vp and high Vp/Vs zones. Tests indicate that models in which this seismic zone is significantly closer to vertical can be confidently rejected. A second high Vp/Vs zone extends to the northeast, apparently dipping beneath the Diablo Range. Another zone of seismicity underlies the northeast portion of this Vp/Vs high. The high Vp/Vs zones cut across areas of very different Vp values, indicating that the high Vp/Vs values are due to the presence of fluids, not just lithology. The close association between the zones of high Vp/Vs and seismicity suggests a direct involvement of fluids in the faulting process. Copyright 1997 by the American Geophysical Union.

Logs and Geologic Data from a Paleoseismic Investigation of the Susitna Glacier fault, Central Alaska Range, Alaska

USGS Publications Warehouse

Personius, Stephen F.; Crone, Anthony J.; Burns, Patricia A.C.; Beget, James E.; Seitz, Gordon G.; Bemis, Sean P.

2010-01-01

This report contains field and laboratory data from a paleoseismic study of the Susitna Glacier fault, Alaska. The initial M 7.2 subevent of the November 3, 2002, M 7.9 Denali fault earthquake sequence produced a 48-km-long set of complex fault scarps, folds, and aligned landslides on the previously unknown, north-dipping Susitna Glacier thrust fault along the southern margin of the Alaska Range in central Alaska. Most of the 2002 folds and fault scarps are 1-3 m high, implying dip-slip thrust offsets (assuming a near-surface fault dip of approximately 20 degrees)of 3-5 m. Locally, some of the 2002 ruptures were superimposed on preexisting scarps that have as much as 5-10 m of vertical separation and are evidence of previous surface-rupturing earthquakes on the Susitna Glacier fault. In 2003-2005, we focused follow-up studies on several of the large scarps at the 'Wet fan' site in the central part of the 2002 rupture to determine the pre-2002 history of large surface-rupturing earthquakes on the fault. We chose this site for several reasons: (1) the presence of pre-2002 thrust- and normal-fault scarps on a gently sloping, post-glacial alluvial fan; (2) nearby natural exposures of underlying fan sediments revealed fine-grained fluvial silts with peat layers and volcanic ash beds useful for chronological control; and (3) a lack of permafrost to a depth of more than 1 m. Our studies included detailed mapping, fault-scarp profiling, and logging of three hand-excavated trenches. We were forced to restrict our excavations to 1- to 2-m-high splay faults and folds because the primary 2002 ruptures mostly were superimposed on such large scarps that it was impossible to hand dig through the hanging wall to expose the fault plane. Additional complications are the pervasive effects of cryogenic processes (mainly solifluction) that can mask or mimic tectonic deformation. The purpose of this report is to present photomosaics, trench logs, scarp profiles, and fault slip, radiocarbon, tephrochronologic, and unit description data obtained during this investigation. We do not attempt to use the data presented herein to construct a paleoseismic history of the Susitna Glacier fault; that history will be the subject of a future report. When completed, our results will be used to compare the Susitna Glacier fault paleoseismic record with results of similar studies on the nearby Denali fault to determine if the simultaneous rupture of these two faults during the 2002 Denali fault earthquake sequence is typical or atypical of their long-term interaction.

Syn-extensional lithogenetic sequences of the Soledad basin, central Transverse Ranges: Implications for detachment-fault models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendrix, E.D.

1993-04-01

The Soledad Basin (central Transverse Ranges, CA) contains the first recognized example of mid-Tertiary detachment-faulting west of the San Andreas fault. Displacements along the Pelona detachment fault and syn-extensional upper-plate sedimentation occurred between [approximately] 26--18 Ma, resulting in deposition of at least 4 separate lithogenetic sequences (LS) which record distinct phases of crustal response to extension. The 1st LS (lower Vasquez Fm.) predates syn-extensional volcanism and records initial basin subsidence along small, discontinuous faults. The 2nd LS (middle Vasquez Fm.) consists of both volcanic and sedimentary strata and signals simultaneous onset of magmatism and initial development of a well-defined networkmore » of high-angle, upper-plate normal faults, creating 2 separate sub-basins. Resulting alluvial fans were non-entrenched, implying that subsidence rates, and thus vertical displacement rates on high-angle faults, equaled or exceeded an estimated average sedimentation rate of 1.4 mm/yr. The 3rd LS (upper Vasquez Fm.) reflects transition to a single, well-integrated depositional basin characterized by streamflood sedimentation. This suggests an enlarged drainage basin and a decrease in subsidence rate relative to sedimentation rate, triggered possibly by uplift of the detachment lower-plate. The 4th LS (Tick Canyon Fm.) lies with angular unconformity above the 3rd LS and contains the 1st clasts eroded from the detachment lower plate. Detachment faulting in the Soledad basin appears to involve, in part, reactivation of structural zones of weakness along the Vincent thrust. Preliminary reconstructions of Soledad extension imply 25--30 km of displacement along the Pelona detachment fault system at an averaged slip rate of 3.6--4.3 mm/yr.« less

Boundary element analysis of active mountain building and stress heterogeneity proximal to the 2015 Nepal earthquake

NASA Astrophysics Data System (ADS)

Thompson, T. B.; Meade, B. J.

2015-12-01

The Himalayas are the tallest mountains on Earth with ten peaks exceeding 8000 meters, including Mt. Everest. The geometrically complex fault system at the Himalayan Range Front produces both great relief and great earthquakes, like the recent Mw=7.8 Nepal rupture. Here, we develop geometrically accurate elastic boundary element models of the fault system at the Himalayan Range Front including the Main Central Thrust, South Tibetan Detachment, Main Frontal Thrust, Main Boundary Thrust, the basal detachment, and surface topography. Using these models, we constrain the tectonic driving forces and frictional fault strength required to explain Quaternary fault slip rate estimates. These models provide a characterization of the heterogeneity of internal stress in the region surrounding the 2015 Nepal earthquake.

Accommodation of missing shear strain in the Central Walker Lane, western North America: Constraints from dense GPS measurements

NASA Astrophysics Data System (ADS)

Bormann, Jayne M.; Hammond, William C.; Kreemer, Corné; Blewitt, Geoffrey

2016-04-01

We present 264 new interseismic GPS velocities from the Mobile Array of GPS for Nevada Transtension (MAGNET) and continuous GPS networks that measure Pacific-North American plate boundary deformation in the Central Walker Lane. Relative to a North America-fixed reference frame, northwestward velocities increase smoothly from ∼4 mm/yr in the Basin and Range province to 12.2 mm/yr in the central Sierra Nevada resulting in a Central Walker Lane deformation budget of ∼8 mm/yr. We use an elastic block model to estimate fault slip and block rotation rates and patterns of deformation from the GPS velocities. Right-lateral shear is distributed throughout the Central Walker Lane with strike-slip rates generally <1.5 mm/yr predicted by the block model, but extension rates are highest near north-striking normal faults found along the Sierra Nevada frontal fault system and in a left-stepping, en-echelon series of asymmetric basins that extend from Walker Lake to Lake Tahoe. Neotectonic studies in the western Central Walker Lane find little evidence of strike-slip or oblique faulting in the asymmetric basins, prompting the suggestion that dextral deformation in this region is accommodated through clockwise block rotations. We test this hypothesis and show that a model relying solely on the combination of clockwise block rotations and normal faulting to accommodate dextral transtensional strain accumulation systematically misfits the GPS data in comparison with our preferred model. This suggests that some component of oblique or partitioned right-lateral fault slip is needed to accommodate shear in the asymmetric basins of the western Central Walker Lane. Present-day clockwise vertical axis rotation rates in the Bodie Hills, Carson Domain, and Mina Deflection are between 1-4°/Myr, lower than published paleomagnetic rotation rates, suggesting that block rotation rates have decreased since the Late to Middle Miocene.

Coping with naturally high levels of soil salinity and boron in the westside of central California

USDA-ARS?s Scientific Manuscript database

In the Westside of central California, over 200,000 ha exhibit naturally high levels of salinity and boron (B). The Coast Ranges of the west central California evolved from complex folding and faulting of sedimentary and igneous rocks of Mesozoic and Tertiary age. Cretaceous and Tertiary marine sedi...

Tectonic reversal of the western Doruneh Fault System: Implications for Central Asian tectonics

NASA Astrophysics Data System (ADS)

Javadi, Hamid Reza; Esterabi Ashtiani, Marzieh; Guest, Bernard; Yassaghi, Ali; Ghassemi, Mohammad Reza; Shahpasandzadeh, Majid; Naeimi, Amir

2015-10-01

The left-lateral Doruneh Fault System (DFS) bounds the north margin of the Central Iranian microplate and has played an important role in the structural evolution of the Turkish-Iranian plateau. The western termination of the DFS is a sinistral synthetic branch fault array that shows clear kinematic evidence of having undergone recent slip sense inversion from a dextral array to a sinistral array in the latest Neogene or earliest Quaternary. Similarly, kinematic evidence from the Anarak Metamorphic complex suggests that this complex initially developed at a transpressive left-stepping termination of the DFS and that it was inverted in the latest Neogene to a transtensional fault termination. The recognition that the DFS and other faults in NE Iran were inverted from dextral to sinistral strike slip in the latest Neogene and the likely connection between the DFS and the Herat Fault of Afghanistan suggests that prior to the latest Miocene, all of the north Iranian and northern Afghan ranges were part of a distributed dextral fault network that extended from the west Himalayan syntaxes to the western Alborz. Also, the recognition that regional slip sense inversion occurred across northern and northeastern Iran after the latest Miocene invalidates tectonic models that extrapolate Pleistocene to recent fault slip kinematics and rates back beyond this time.

Highly focused asymmetric surface uplift and bedrock exhumation along the San Gregorio-Hosgri fault in the Santa Lucia range, central California

NASA Astrophysics Data System (ADS)

Steely, A.; Hourigan, J. K.; Mere, A.; Orme, D. A.; Ooms, J.; Gallagher, C.

2016-12-01

We use two new datasets to constrain the Late Cretaceous through modern history of vertical deformation in the Santa Lucia range of the central California coast to better understand the tectonic evolution of the plate boundary between the San Andreas fault and San Gregorio-Hosgri fault (SGHF). New data presented here include 46 apatite and 31 zircon (U-Th)/He ages and 1,200 elevation measurements of the first marine terrace (presumably the MIS 5a or 5e terrace) along 190 km of coastline. The San Gregorio-Hosgri fault (SGHF) initiated in the late Miocene and appears to have asymmetrically focused exhumation on its NE side. Apatite ages are 1.5-4 Ma directly NE of the fault in both crystalline and Franciscan bedrock, but 20-60 Ma older directly SW of the fault or >5 km NE of the fault; zircon ages reflect a similar pattern and are as young as 8 Ma directly NE of the fault. These data appear to show that bedrock exhumation has been highly focused in narrow fault slivers parallel and subparallel to the SGHF and has been sufficient to exhume apatite and zircon from below their partial retention zones. We suggest that this focusing may occur along pre-existing weak faults in crustal blocks with shallow (<10 km) underplated schist—a rheologic feature of the Salinian bedrock in the Santa Lucia range not found in the surrounding crustal blocks. Surveys of the lowest marine terrace south from Monterey and northwest from Santa Cruz show a similar asymmetric pattern of increasing elevation towards the SGHF. The terrace south of Monterey rises gently from 5 m to 20 m above MSL obliquely southward toward the fault. After crossing into one of the highly exhumed crustal blocks, the terrace rises sharply to over 84 m and then drops sharply after crossing the fault zone. Inferred uplift rates from the late Quaternary (0.7-1.1 mm/yr) are higher than those during the main late Miocene-Pliocene phase of activity on the SGHF ( 0.3 mm/yr). This is puzzling in light of the low rates of modern seismicity along the SGHF and the lack of large late Quaternary horizontal offset and may suggest that the SGHF along the Santa Lucia range is more active (or active in a different way) than previously thought.

Quantification of fluvial response to tectonic deformation in the Central Pontides, Turkey; inferences from OSL dating of fluvial terraces

NASA Astrophysics Data System (ADS)

McClain, Kevin; Yıldırım, Cengiz; Çiner, Attila; Akif Sarıkaya, M.; Şahin, Sefa; Özcan, Orkan; Güneç Kıyak, Nafiye; Öztürk, Tuǧba

2017-04-01

From Late Miocene to present, Anatolia's rapid counterclockwise movement, which increases in velocity towards the Hellenic Arc, has formed the North Anatolian Fault (NAF), a dextral transform fault along the Anatolia-Eurasia plate boundary and the northern margin of the Central Anatolian Plateau (CAP). A zone of transpression referred to as the Central Pontides exists between the broad restraining bend of the NAF and the Black Sea Basin, uplifting what is interpreted as a detached flower structure. Dating of Quaternary landforms in the eastern flank of the Central Pontides has helped to understand its recent deformation. However, in the western flank of the Central Pontides there is an absence of Quaternary studies, relatively quiet modern seismicity, and difficulties locating or observing fault scarps. This led us to use optically stimulated luminescence dating (OSL-dating) of fluvial terrace sediments and the study of geomorphic features to gain insight into the influence of climate and tectonics on landscape evolution of this area. In this area, the Filyos River crosses the Karabük Fault (reverse fault) and deeply incises a gorge through the Karabük Range before flowing towards the Black Sea. In the gorge an abundance of indicators of tectonic deformation were mapped, such as hanging valleys, wind gaps, bedrock gorges, landslides, steep V-shaped channels, tilted basins, as well as fluvial strath terraces. In particular, strath terraces of at least 8 levels within just 1.5 km of horizontal distance were examined. We used OSL-dating to estimate five deposition ages of fluvial strath terrace sediments, leading to an estimation of incision and uplift rates over time. Using three samples per terrace with strath elevations of 246 ± 0.2 m, 105.49 ± 0.2 m, 43.6 ± 0.2 m, 15.3 ± 0.2 m and 3.6 ± 0.2 m above the Filyos River, we determined corresponding ages of 841 ± 76 ka, 681 ± 49 ka, 386 ± 18 ka, 88 ± 5.1 ka and 50.9 ± 2.8 ka. Incision rates over time (oldest terrace to youngest) suggest uplift of 0.29 ± 0.03 mm/y, 0.16 ± 0.01 mm/y, 0.10 ± 0.01 mm/y, 0.17 ± 0.01 mm/y and 0.07 ± 0.004 mm/y. Collectively, our ages infer decelerating fluvial incision and rock uplift rates in the Karabük Range of the Central Pontides. The highest rate that belongs to oldest terrace level (841 ± 76 ka) also implies long-term mean uplift, which is well correlated with long term ( 350 ka) mean uplift rate obtained from fluvial terraces in the eastern flank of the (Gökırmak Basin) Central Pontides. These results indicate Quaternary activity of the Karabük Fault despite the fact that very low modern seismicity and partition of strain in the north of the North Anatolian Fault. Keywords: Tectonics, Geomorphology, Fluvial Terrace, OSL Dating, Central Pontides, North Anatolian Fault, Filyos River, Turkey, Central Anatolian Plateau

Along-Strike Variation in Geometry and Kinematics of a Major, Active Intracontinental Thrust System: the Pred-Terskey Fault Zone, Kyrgyz Tien Shan, Central Asia

NASA Astrophysics Data System (ADS)

Burgette, R. J.; Weldon, R. J.; Abdrakhmatov, K. Y.; Ormukov, C.

2004-12-01

The Pred-Terskey fault zone defines the southern margin of the Issyk-Kul basin, extending eastward over 250 km from at least the Chu River to the Kazakhstan border, and appears to be one of the most active zones in the Kyrgyz Tien Shan. Despite a diversity of structural styles and changes of vergence at the surface, the lateral continuity and overall geometry of the zone is consistent with a single north vergent thrust at depth, which uplifts the Terskey Range and generally tilts the south margin of the basin to the north. This northward tilting of the margin is probably due to a flattening of the fault as it approaches the surface. In spite of historical quiescence, it is likely capable of producing great earthquakes. We have conducted detailed field mapping coupled with terrace profiling and dating at seven representative, well-exposed areas of the fault zone. Based on these field observations and satellite image and air photo interpretation along the entire zone, we identify three major divisions in structural style expressed at the surface. The western segment is typified by the Tura-Su, Ak-Terek and Ton areas. A series of left-stepping, south-vergent, basement-involved reverse faults and folds are uplifting the southern margin of the Issyk-Kul basin in this area. The resulting uphill-facing scarps have trapped and diverted many of the rivers flowing north from the Terskey Range. Tertiary strata and Quaternary geomorphic surfaces show consistent, progressive northward tilting across the entire zone. The west-central segment is represented by the Kajy-Say area. South-vergent reverse faults and a north-vergent backthrust have uplifted an arcuate granite block. Offshore of this area, the lake floor descends to a sharp break in slope with a low relief area at a depth of about 650 m. Late Quaternary geomorphic features do not show evidence of tilting. In contrast to the areas east and west, the major north-dipping thrust is likely planar over this segment and daylights at the lake floor break in slope. The east-central segment is exemplified by the Barskaun and Jety Oguz areas. A high angle reverse fault juxtaposes Paleozoic rock against Tertiary sediments. To the north, a thrust fault with a sinuous trace places north-dipping Tertiary rock over the nearly horizontal basin floor. Quaternary terraces in the hanging wall of this fault record progressive northward tilting. North of the thrust fault a series of anticlines are growing out of the basin sediments. The eastern segment, which includes the Jergalan River valley, lacks a low angle thrust fault at the basin margin. Along this segment, the basement reverse fault uplifts Paleozoic rock against Quaternary basin sediment. To the north of this range-bounding structure, late Quaternary terraces are offset by south-vergent scarps. We are calculating geologic slip rates for each of the seven sites along the Pred-Terskey zone by dating terraces and constructing structural models consistent with both the rock and terrace records. Based on preliminary radiocarbon dates, a prominent Jety Oguz River terrace is 50 +/- 10 ka. The terrace is tilted 0.5° relative to the modern river, and with the low angle fault branching off of the basement reverse fault at dips ranging between 45° and 90° , the slip rate of this fault is 6 +/- 4 mm/yr. This is consistent with the GPS shortening rate across the Pred-Terskey zone at this longitude.

Counterclockwise rotations in the Late Eocene-Oligocene volcanic fields of San Luis Potosí and Sierra de Guanajuato (eastern Mesa Central, Mexico)

NASA Astrophysics Data System (ADS)

Andreani, Louis; Gattacceca, Jerôme; Rangin, Claude; Martínez-Reyes, Juventino; Demory, François

2014-12-01

We used paleomagnetic and structural data to investigate the late Eocene-Oligocene tectonic evolution of the Mesa Central area in Mexico. The Mesa Central was affected by NW-trending faults (Tepehuanes-San Luis fault system) coeval with a Late Eocene-Oligocene ignimbrite flare-up and by post-27 Ma NNE-trending grabens related to the Basin and Range. We obtained reliable paleomagnetic directions from 61 sites within the Late Eocene-Oligocene volcanic series (~ 30 to ~ 27 Ma) of the San Luis Potosí volcanic field and Sierra de Guanajuato. For each site we also measured the anisotropy of magnetic susceptibility (AMS). Tilt corrections were made using AMS data for 33 sites where in situ bedding measurements were not available. Paleomagnetic directions indicate counterclockwise rotations of about 10° with respect to stable North America after 30-25 Ma. Structural data suggest that the volcanic succession was mainly affected by normal faults. However, we also found evidences for oblique or horizontal striae showing a left-lateral component along NW-trending faults and a right lateral component along NE-trending faults. Both motions are consistent with a N-S extension oblique to the Tepehuanes-San Luis fault system. Previous paleomagnetic studies in northern and southern Mexico show the prevalence of minor left-lateral shear components along regional-scale transpressional and transtensional lineaments. Our paleomagnetic data may reflect thus small vertical-axis rotations related to a minor shear component coeval with the Oligocene intra-arc extension in central Mexico.

Imaging the complexity of an active normal fault system: The 1997 Colfiorito (central Italy) case study

USGS Publications Warehouse

Chiaraluce, L.; Ellsworth, W.L.; Chiarabba, C.; Cocco, M.

2003-01-01

Six moderate magnitude earthquakes (5 < Mw < 6) ruptured normal fault segments of the southern sector of the North Apennine belt (central Italy) in the 1997 Colfiorito earthquake sequence. We study the progressive activation of adjacent and nearby parallel faults of this complex normal fault system using ???1650 earthquake locations obtained by applying a double-difference location method, using travel time picks and waveform cross-correlation measurements. The lateral extent of the fault segments range from 5 to 10 km and make up a broad, ???45 km long, NW trending fault system. The geometry of each segment is quite simple and consists of planar faults gently dipping toward SW with an average dip of 40??-45??. The fault planes are not listric but maintain a constant dip through the entire seismogenic volume, down to 8 km depth. We observe the activation of faults on the hanging wall and the absence of seismicity in the footwall of the structure. The observed fault segmentation appears to be due to the lateral heterogeneity of the upper crust: preexisting thrusts inherited from Neogene's compressional tectonic intersect the active normal faults and control their maximum length. The stress tensor obtained by inverting the six main shock focal mechanisms of the sequence is in agreement with the tectonic stress active in the inner chain of the Apennine, revealing a clear NE trending extension direction. Aftershock focal mechanisms show a consistent extensional kinematics, 70% of which are mechanically consistent with the main shock stress field.

Armenia-To Trans-Boundary Fault: AN Example of International Cooperation in the Caucasus

NASA Astrophysics Data System (ADS)

Karakhanyan, A.; Avagyan, A.; Avanesyan, M.; Elashvili, M.; Godoladze, T.; Javakishvili, Z.; Korzhenkov, A.; Philip, S.; Vergino, E. S.

2012-12-01

Studies of a trans-boundary active fault that cuts through the border of Armenia to Georgia in the area of the Javakheti volcanic highland have been conducted since 2007. The studies have been implemented based on the ISTC 1418 and NATO SfP 983284 Projects. The Javakheti Fault is oriented to the north-northwest and consists of individual segments displaying clear left-stepping trend. Fault mechanism is represented by right-lateral strike-slip with normal-fault component. The fault formed distinct scarps, deforming young volcanic and glacial sediments. The maximum-size displacements are recorded in the central part of the fault and range up to 150-200 m by normal fault and 700-900 m by right-lateral strike-slip fault. On both flanks, fault scarps have younger appearance, and displacement size there decreases to tens of meters. Fault length is 80 km, suggesting that maximum fault magnitude is estimated at 7.3 according to the Wells and Coppersmith (1994) relation. Many minor earthquakes and a few stronger events (1088, Mw=6.4, 1899 Mw=6.4, 1912, Mw=6.4 and 1925, Mw=5.6) are associated with the fault. In 2011/2012, we conducted paleoseismological and archeoseismological studies of the fault. By two paleoseismological trenches were excavated in the central part of the fault, and on its northern and southern flanks. The trenches enabled recording at least three strong ancient earthquakes. Presently, results of radiocarbon age estimations of those events are expected. The Javakheti Fault may pose considerable seismic hazard for trans-boundary areas of Armenia and Georgia as its northern flank is located at the distance of 15 km from the Baku-Ceyhan pipeline.

Investigating Crustal Scale Fault Systems Controlling Volcanic and Hydrothermal Fluid Processes in the South-Central Andes, First Results from a Magnetotelluric Survey

NASA Astrophysics Data System (ADS)

Pearce, R.; Mitchell, T. M.; Moorkamp, M.; Araya, J.; Cembrano, J. M.; Yanez, G. A.; Hammond, J. O. S.

2017-12-01

At convergent plate boundaries, volcanic orogeny is largely controlled by major thrust fault systems that act as magmatic and hydrothermal fluid conduits through the crust. In the south-central Andes, the volcanically and seismically active Tinguiririca and Planchon-Peteroa volcanoes are considered to be tectonically related to the major El Fierro thrust fault system. These large scale reverse faults are characterized by 500 - 1000m wide hydrothermally altered fault cores, which possess a distinct conductive signature relative to surrounding lithology. In order to establish the subsurface architecture of these fault systems, such conductivity contrasts can be detected using the magnetotelluric method. In this study, LEMI fluxgate-magnetometer long-period and Metronix broadband MT data were collected at 21 sites in a 40km2 survey grid that surrounds this fault system and associated volcanic complexes. Multi-remote referencing techniques is used together with robust processing to obtain reliable impedance estimates between 100 Hz and 1,000s. Our preliminary inversion results provide evidence of structures within the 10 - 20 km depth range that are attributed to this fault system. Further inversions will be conducted to determine the approximate depth extent of these features, and ultimately provide constraints for future geophysical studies aimed to deduce the role of these faults in volcanic orogeny and hydrothermal fluid migration processes in this region of the Andes.

Active tectonics of the Binalud Mountains, a key puzzle segment to describe Quaternary deformations at the northeastern boundary of the Arabia-Eurasia collision

NASA Astrophysics Data System (ADS)

Shabanian, Esmaeil; Bellier, Olivier; Siame, Lionel L.; Abbassi, Mohammad R.; Leanni, Laetitia; Braucher, Régis; Farbod, Yassaman; Bourlès, Didier L.

2010-05-01

In northeast Iran, the Binalud Mountains accommodate part of active convergence between the Arabian and Eurasian plates. This fault-bounded mountain range has been considered a key region to describe Quaternary deformations at the northeastern boundary of the Arabia-Eurasia collision. But, the lack of knowledge on active faulting hampered evaluating the geological reliability of tectonic models describing the kinematics of deformation in northeast Iran. Morphotectonic investigations along both sides of the Binalud Mountains allowed us to characterize the structural and active faulting patterns along the Neyshabur and Mashhad fault systems on the southwest and northeast sides of the mountain range, respectively. We applied combined approaches of morphotectonic analyses based on satellite imageries (SPOT5 and Landsat ETM+), STRM and site-scale digital topographic data, and field surveys complemented with in situ-produced 10Be exposure dating to determine the kinematics and rate of active faulting. Three regional episodes of alluvial surface abandonments were dated at 5.3±1.1 kyr (Q1), 94±5 kyr (Q3), and 200±14 kyr (S3). The geomorphic reconstruction of both vertical and right-lateral fault offsets postdating these surface abandonment episodes yielded Quaternary fault slip rates on both sides of the Binalud Mountains. On the Neyshabur Fault System, thanks to geomorphic reconstructions of cumulative offsets recorded by Q3 fan surfaces, slip rates of 2.7±0.8 mm/yr and 2.4±0.2 mm/yr are estimated for right-lateral and reverse components of active faulting, respectively. Those indicate a total slip rate of 3.6±1.2 mm/yr for the late Quaternary deformation on the southwest flank of the Binalud Mountains. Reconstructing the cumulative right-lateral offset recorded by S3 surfaces, a middle-late Quaternary slip rate of 1.6±0.1 mm/yr is determined for the Mashhad Fault System. Altogether, our geomorphic observations reveal that, on both sides of the Binalud Mountains, the relative motion between central Iran and Eurasia is partly taken-up by dextral-reverse oblique-slip faulting along the Neyshabur and Mashhad fault systems. This faulting mechanism implies a long-term rate of ~4 mm/yr for the range-parallel strike-slip faulting, and an uplift rate of ~2.4 mm/yr due to the range-normal shortening during late Quaternary. Our data provide the first geological constraints on the rate of active faulting on both sides of the Binalud Mountains, and allow us to examine the geological reliability of preexisting tectonic models proposed to describe the kinematics of active deformation at the northeastern boundary of the Arabia-Eurasia collision. Our results favor the northward translation of central Iran with respect to Eurasia through strike-slip faulting localized along distinct crustal scale fault systems rather than systematic block rotations around vertical axes.

The complex architecture of the 2009 MW 6.1 L'Aquila normal fault system (Central Italy) as imaged by 64,000 high-resolution aftershock locations

NASA Astrophysics Data System (ADS)

Valoroso, L.; Chiaraluce, L.; Di Stefano, R.; Piccinini, D.; Schaff, D. P.; Waldhauser, F.

2011-12-01

On April 6th 2009, a MW 6.1 normal faulting earthquake struck the axial area of the Abruzzo region in Central Italy. We present high-precision hypocenter locations of an extraordinary dataset composed by 64,000 earthquakes recorded at a very dense seismic network of 60 stations operating for 9 months after the main event. Events span in magnitude (ML) between -0.9 to 5.9, reaching a completeness magnitude of 0.7. The dataset has been processed by integrating an accurate automatic picking procedure together with cross-correlation and double-difference relative location methods. The combined use of these procedures results in earthquake relative location uncertainties in the range of a few meters to tens of meters, comparable/lower than the spatial dimension of the earthquakes themselves). This data set allows us to image the complex inner geometry of individual faults from the kilometre to meter scale. The aftershock distribution illuminates the anatomy of the en-echelon fault system composed of two major faults. The mainshock breaks the entire upper crust from 10 km depth to the surface along a 14-km long normal fault. A second segment, located north of the normal fault and activated by two Mw>5 events, shows a striking listric geometry completely blind. We focus on the analysis of about 300 clusters of co-located events to characterize the mechanical behavior of the different portions of the fault system. The number of events in each cluster ranges from 4 to 24 events and they exhibit strongly correlated seismograms at common stations. They mostly occur where secondary structures join the main fault planes and along unfavorably oriented segments. Moreover, larger clusters nucleate on secondary faults located in the overlapping area between the two main segments, where the rate of earthquake production is very high with a long-lasting seismic decay.

Kinematics of wrench and divergent-wrench deformation along a central part of the Border Ranges Fault System, Northern Chugach Mountains, Alaska

NASA Astrophysics Data System (ADS)

Little, Timothy A.

1990-08-01

The Border Ranges fault system (BRFS) bounds the inboard edge of the subduction-accretion complex of southern Alaska. In Eocene time a central segment of this fault system was reactivated as a zone of dextral wrench- and oblique-slip faulting having a cumulative strike-slip offset of at least several tens of kilometers, but probably less than 100 km. Early wrench folds are upright, trend at less than 45° to the strike of adjacent faults and developed with fold axes oriented subparallel to the axis of maximum incremental stretch λ1. These en echelon folds rotated and tightened with progressive deformation and then were overprinted by younger wrench folds that trend at about 60° to adjacent throughgoing faults. The latter folds are interpreted as forming during a late increment of distributed wrench deformation within the BRFS that included a component of extension (divergence) orthogonal to the mean strike of the fault system. A sharp releasing bend in exposures of a strike-slip fault originally at >4 km depth today coincides with a narrow pull-apart graben bounded by oblique-normal faults that dip toward the basin. Widening of this pull-apart graben by brittle faulting and dike intrusion accommodated less than 2 km of strike-slip and was a late-stage phenomenon, possibly occurring at supracrustal levels. Prior to formation of this graben during a period of predominantly ductile deformation at deeper structural levels, wrench-folded rocks on one side of the nonplanar fault were translated around the releasing bend without significant faulting or loss of coherence. Kinematically, the earlier deformation was accomplished by fault-bend folding and rotation of a relatively deformable block as it passed through a system of upright megakinks. Such a ductile mechanism of fault block translation around a strike-slip bend may be typical of intermediate levels of the crust beneath pull-apart grabens and may be transitional downward into heterogeneous laminar flow occuring along curved segments of ductile shear zones. Some degree of fault-bend folding of strike-slip fault blocks around releasing bends may be one reason why the amount of extension measured across natural pull-apart basins is commonly observed to be less than the amount of strike-slip along their master faults.

Fault propagation folds induced by gravitational failure and slumping of the Central Costa Rica volcanic range: Implications for large terrestrial and Martian volcanic edifices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borgia, A.; Burr, J.; Montero, W.

1990-08-30

Long sublinear ridges and related scarps located at the base of large volcanic structures are frequently interpreted as normal faults associated with extensional regional stress. In contrast, the ridges bordering the Central Costa Rica volcanic range (CCRVR) are the topographic expression of hanging wall asymmetric angular anticlines overlying low-angle thrust faults at the base of the range. These faults formed by gravitational failure and slumping of the flanks of the range due to the weight of the volcanic edifices and were perhaps triggered by the intrusion of magma over the past 20,000 years. These anticlines are hypothesized to occur alongmore » the base of the volcano, where the thrust faults ramp up toward the sea bottom. Ridges and scarps between 2,000 and 5,000 m below sea level are interpreted as the topographic expression of these folds. The authors further suggest that the scarps of the CCRVR and valid scaled terrestrial analogs of the perimeter scarp of the Martian volcano Olympus Mons. They suggest that the crust below Olympus Mons has failed under the load of the volcano, triggering the radial slumping of the flanks of the volcano on basal thrusts. The thrusting would have, in turn, formed the anticlinal ridges and scarps that surround the edifice. The thrust faults may extend all the way to the base of the Martian crust (about 40 km), and they may have been active until almost the end of the volcanic activity. They suggest that gravitational failure and slumping of the flanks of volcanoes is a process common to most large volcanic edifices. In the CCRVR this slumping of the flanks is a slow intermittent process, but it could evolve to rapid massive avalanching leading to catastrophic eruptions. Thus monitoring of uplift and displacement of the folds related to the slump tectonics could become an additional effective method for mitigating volcanic hazards.« less

Structural evolution and tectonic style of the Tunisian central Atlas; role of inherited faults in compressive tectonics (Ghoualguia anticline)

NASA Astrophysics Data System (ADS)

Briki, Haithem; Ahmadi, Riadh; Smida, Rabiaa; Rekhiss, Farhat

2018-04-01

Geological mapping, field cross sections, structural analyses and new subsurface data were used to characterize the geometry and tectonic setting of the Ghoualguia structure, which is an E-W-trending anticline located between the Kalaa Khasba and Rouhia troughs of the central Tunisian Atlas. The results show an important NE-SW extensional phase during the Mesozoic, as demonstrated by synsedimentary normal faults (NW-SE and E-W) and thickness variations. In the Aouled Mdoua area, the absence of Paleocene-Eocene rocks indicates that the eastern and western parts of the Ghoualguia structure were separated by high topography. In addition, the angular unconformity observed between the Upper Cretaceous unit (Abiod Fm.) and the upper Eocene series (Souar Fm.) provide evidence of a tilted-block structure delineated by North-South faults. A major compressional phase during the middle to late Miocene created various detachment levels that originated mainly in the Triassic and Cretaceous deposits. Faults were reactivated as thrust and strike-slip faults, creating fault-related fold structures. In the core of the Ghoualguia fold, an original S-dipping normal fault underwent reverse movement as a back thrust. Fault-slip data indicate that the area records a major NE-SW extensional phase that took place during the late Miocene and Pliocene. A balanced cross section provides insight into the existence of two main detachment levels rooted in the Triassic (depth ± 6 km) and the lower Cretaceous (depth ± 2.5 km). The balanced cross section highlights a shortening of about 2.5 km along cross section and 1.5 km in the central part of the Ghoualguia anticline. This work underlines the predominant role of the inherited Mesozoic structures during the evolution of the Atlassic range and their influence on the geometry of the central Tunisian atlas.

Preliminary Pseudo 3-D Imagery of the State Line Fault, Stewart Valley, Nevada Using Seismic Reflection Data

NASA Astrophysics Data System (ADS)

Saldaña, S. C.; Snelson, C. M.; Taylor, W. J.; Beachly, M.; Cox, C. M.; Davis, R.; Stropky, M.; Phillips, R.; Robins, C.; Cothrun, C.

2007-12-01

The Pahrump Fault system is located in the central Basin and Range region and consists of three main fault zones: the Nopah range front fault zone, the State Line fault zone and the Spring Mountains range fault zone. The State Line fault zone is made up north-west trending dextral strike-slip faults that run parallel to the Nevada- California border. Previous geologic and geophysical studies conducted in and around Stewart Valley, located ~90 km from Las Vegas, Nevada, have constrained the location of the State Line fault zone to within a few kilometers. The goals of this project were to use seismic methods to definitively locate the northwestern most trace of the State Line fault and produce pseudo 3-D seismic cross-sections that can then be used to characterize the subsurface geometry and determine the slip of the State Line fault. During July 2007, four seismic lines were acquired in Stewart Valley: two normal and two parallel to the mapped traces of the State Line fault. Presented here are preliminary results from the two seismic lines acquired normal to the fault. These lines were acquired utilizing a 144-channel geode system with each of the 4.5 Hz vertical geophones set out at 5 m intervals to produce a 595 m long profile to the north and a 715 m long profile to the south. The vibroseis was programmed to produce an 8 s linear sweep from 20-160 Hz. These data returned excellent signal to noise and reveal subsurface lithology that will subsequently be used to resolve the subsurface geometry of the State Line fault. This knowledge will then enhance our understanding of the evolution of the State Line fault. Knowing how the State Line fault has evolved gives insight into the stick-slip fault evolution for the region and may improve understanding of how stress has been partitioned from larger strike-slip systems such as the San Andreas fault.

Preliminary isostatic residual gravity anomaly map of Paso Robles 30 x 60 minute quadrangle, California

USGS Publications Warehouse

McPhee, D.K.; Langenheim, V.E.; Watt, J.T.

2011-01-01

This isostatic residual gravity map is part of an effort to map the three-dimensional distribution of rocks in the central California Coast Ranges and will serve as a basis for modeling the shape of basins and for determining the location and geometry of faults within the Paso Robles quadrangle. Local spatial variations in the Earth\\'s gravity field, after accounting for variations caused by elevation, terrain, and deep crustal structure reflect the distribution of densities in the mid- to upper crust. Densities often can be related to rock type, and abrupt spatial changes in density commonly mark lithological or structural boundaries. High-density rocks exposed within the central Coast Ranges include Mesozoic granitic rocks (exposed northwest of Paso Robles), Jurassic to Cretaceous marine strata of the Great Valley Sequence (exposed primarily northeast of the San Andreas fault), and Mesozoic sedimentary and volcanic rocks of the Franciscan Complex [exposed in the Santa Lucia Range and northeast of the San Andreas fault (SAF) near Parkfield, California]. Alluvial sediments and Tertiary sedimentary rocks are characterized by low densities; however, with increasing depth of burial and age, the densities of these rocks may become indistinguishable from those of older basement rocks.

A model for the geomorphic development of normal-fault facets

NASA Astrophysics Data System (ADS)

Tucker, G. E.; Hobley, D. E. J.; McCoy, S. W.

2014-12-01

Triangular facets are among the most striking landforms associated with normal faulting. The genesis of facets is of great interest both for the information facets contain about tectonic motion, and because the progressive emergence of facets makes them potential recorders of both geomorphic and tectonic history. In this report, we present observations of triangular facets in the western United States and in the Italian Central Apennines. Facets in these regions typically form quasi-planar surfaces that are aligned in series along and above the trace of an active fault. Some facet surfaces consist mainly of exposed bedrock, with a thin and highly discontinuous cover of loose regolith. Other facets are mantled by a several-decimeter-thick regolith cover. Over the course of its morphologic development, a facet slope segment may evolve from a steep (~60 degree) bedrock fault scarp, well above the angle of repose for soil, to a gentler (~20-40 degree) slope that can potentially sustain a coherent regolith cover. This evolutionary trajectory across the angle of repose renders nonlinear diffusion theory inapplicable. To formulate an alternative process-based theory for facet evolution, we use a particle-based approach that acknowledges the possibility for both short- and long-range sediment-grain motions, depending on the topography. The processes of rock weathering, grain entrainment, and grain motion are represented as stochastic state-pair transitions with specified transition rates. The model predicts that facet behavior can range smoothly along the spectrum from a weathering-limited mode to a transport-limited mode, depending on the ratio of fault-slip rate to bare-bedrock regolith production rate. The model also implies that facets formed along a fault with pinned tips should show systematic variation in slope angle that correlates with along-fault position and slip rate. Preliminary observations from central Italy and the eastern Basin and Range are consistent with this prediction.

Influence of fault trend, fault bends, and fault convergence on shallow structure, geomorphology, and hazards, Hosgri strike-slip fault, offshore central California

NASA Astrophysics Data System (ADS)

Johnson, S. Y.; Watt, J. T.; Hartwell, S. R.

2012-12-01

We mapped a ~94-km-long portion of the right-lateral Hosgri Fault Zone from Point Sal to Piedras Blancas in offshore central California using high-resolution seismic reflection profiles, marine magnetic data, and multibeam bathymetry. The database includes 121 seismic profiles across the fault zone and is perhaps the most comprehensive reported survey of the shallow structure of an active strike-slip fault. These data document the location, length, and near-surface continuity of multiple fault strands, highlight fault-zone heterogeneity, and demonstrate the importance of fault trend, fault bends, and fault convergences in the development of shallow structure and tectonic geomorphology. The Hosgri Fault Zone is continuous through the study area passing through a broad arc in which fault trend changes from about 338° to 328° from south to north. The southern ~40 km of the fault zone in this area is more extensional, resulting in accommodation space that is filled by deltaic sediments of the Santa Maria River. The central ~24 km of the fault zone is characterized by oblique convergence of the Hosgri Fault Zone with the more northwest-trending Los Osos and Shoreline Faults. Convergence between these faults has resulted in the formation of local restraining and releasing fault bends, transpressive uplifts, and transtensional basins of varying size and morphology. We present a hypothesis that links development of a paired fault bend to indenting and bulging of the Hosgri Fault by a strong crustal block translated to the northwest along the Shoreline Fault. Two diverging Hosgri Fault strands bounding a central uplifted block characterize the northern ~30 km of the Hosgri Fault in this area. The eastern Hosgri strand passes through releasing and restraining bends; the releasing bend is the primary control on development of an elongate, asymmetric, "Lazy Z" sedimentary basin. The western strand of the Hosgri Fault Zone passes through a significant restraining bend and dies out northward where we propose that its slip transfers to active structures in the Piedras Blancas fold belt. Given the continuity of the Hosgri Fault Zone through our study area, earthquake hazard assessments should incorporate a minimum rupture length of 110 km. Our data do not constrain lateral slip rates on the Hosgri, which probably vary along the fault (both to the north and south) as different structures converge and diverge but are likely in the geodetically estimated range of 2 to 4 mm/yr. More focused mapping of lowstand geomorphic features (e.g., channels, paleoshorelines) has the potential to provide better constraints. The post-Last-Glacial Maximum unconformity is an important surface for constraining vertical deformation, yielding local fault offset rates that may be as high as 1.4 mm/yr and off-fault deformation rates as high as 0.5 mm/yr. These vertical rates are short-term and not sustainable over longer geologic time, emphasizing the complex evolution and dynamics of strike-slip zones.

Structural and lithologic study of northern coast ranges and Sacramento Valley, California

NASA Technical Reports Server (NTRS)

Rich, E. I. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Analysis of ERTS-1 imagery of the Northern California Coast Ranges has disclosed a potential relation between a heretofore unrecognized fracture system and known deposits of mercury and geothermally active areas in the Coast Range and between oil and gas fields in the Sacramento Valley. Three potentially important systems of linear elements within the Coast Ranges, detected on ERTS-1 imagery, may represent fault systems or zones of shearing because topographic offset and stratigraph disruption can be seen along one or two of the lineations. One of the systems in subparallel to the San Andreas fault and is confined to the Pacific Coastal Belt. Another set is confined to the central core of the Coast Ranges. The third set of linear features (Valley System) has not heretofore been recognized. Some of the known mercury deposits and geothermally active areas near Clear Lake, in the Coast Ranges, are along the Valley System or at the intersection of the Central and Valley Systems. The plotted locations of some of the oil and gas fields in the Sacramento Valley are associated with the Valley and/or Central Systems. If these relations prove reliable, the ERTS-1 imagery may prove to be an extremely useful exploration tool.

Chasing the Garlock: A study of tectonic response to vertical axis rotation

NASA Astrophysics Data System (ADS)

Guest, Bernard; Pavlis, Terry L.; Golding, Heather; Serpa, Laura

2003-06-01

Vertical-axis, clockwise block rotations in the Northeast Mojave block are well documented by numerous authors. However, the effects of these rotations on the crust to the north of the Northeast Mojave block have remained unexplored. In this paper we present a model that results from mapping and geochronology conducted in the north and central Owlshead Mountains. The model suggests that some or all of the transtension and rotation observed in the Owlshead Mountains results from tectonic response to a combination of clockwise block rotation in the Northeast Mojave block and Basin and Range extension. The Owlshead Mountains are effectively an accommodation zone that buffers differential extension between the Northeast Mojave block and the Basin and Range. In addition, our model explores the complex interactions that occur between faults and fault blocks at the junction of the Garlock, Brown Mountain, and Owl Lake faults. We hypothesize that the bending of the Garlock fault by rotation of the Northeast Mojave block resulted in a misorientation of the Garlock that forced the Owl Lake fault to break in order to accommodate slip on the western Garlock fault. Subsequent sinistral slip on the Owl Lake fault offset the Garlock, creating the now possibly inactive Mule Springs strand of the Garlock fault. Dextral slip on the Brown Mountain fault then locked the Owl Lake fault, forcing the active Leach Lake strand of the Garlock fault to break.

Quaternary tectonic setting of South-Central coastal California

USGS Publications Warehouse

Lettis, William R.; Hanson, Kathryn L.; Unruh, Jeffrey R.; McLaren, Marcia; Savage, William U.; Keller, Margaret A.

2004-01-01

Recent geodetic, geologic, and seismologic studies show that the south-central coast of California is a region of active Quaternary deformation. Northeast-directed crustal shortening is occurring in a triangular-shaped region between the Hosgri-San Simeon fault system on the west, the Southern Coast Ranges on the northeast, and the western Transverse Ranges on the south. We informally call this region the Los Osos domain. In this study, we conducted detailed geological, seismological, and geophysical investigations to characterize the nature and rates of deformation in the domain. Locations of active and potentially active faults and folds are compiled at a scale of 1:250,000 for the entire domain based primarily on onshore geologic data and offshore geophysical data. Crustal shortening in the domain is accommodated by a series of prominent northwest-trending reverse faults and localized folding. The reverse faults separate distinct structural blocks that have little or no internal deformation. Hangingwall blocks are being uplifted at rates of up to 0.2 mm/yr. Footwall blocks are either static or slowly subsiding at rates of 0.1 mm/yr or less, except for localized areas of concentrated subsidence directly adjacent to some faults. The cumulative rate of crustal shortening is about 1 to 2 mm/yr across the northern part of the domain based on observed geologic deformation. Cumulative shortening across the central and southern parts of the domain is poorly constrained by geologic data and may approach 2 to 3 mm/yr. Historical and instrumental seismicity generally are spatially associated with the uplifted blocks and bordering reverse faults to depths of about 10 km. Together with near-surface geological data and deeper crustal geophysical imaging that show high-angle faulting, the seismicity data indicate that the reverse faults probably extend to the base of the seismogenic crust. The base of the seismogenic crust may correspond with a mid-crustal detachment or decollement surface into which the reverse faults root. We speculate that the detachment may coincide, in part, with the top of a northeast-dipping slab of oceanic crust that extends beneath the western margin of the continent or with the brittle-ductile transition above the subducted slab. The Los Osos domain of north-northeast/south-southwest crustal shortening is structurally detached from the offshore Hosgri Fault Zones. Both the pattern and regional extent of deformation in the Los Osos domain contrast sharply with that of the offshore Santa Maria Basin. The basin is undergoing minor east-northeast/west-southwest crustal shortening at rates of less than 0.1 mm/yr and is moving northwestward at a rate of about 1 to 3 mm/yr relative to the Los Osos domain along the San Simeon and Hosgri Fault Zones. Geodetic data and the kinematics of north-northeast-directed crustal shortening of the Los Osos domain east of the Hosgri Fault Zone show that the rate and cumulative amount of right-slip along the Hosgri Fault Zone progressively decrease southward. Quaternary deformation within the Los Osos domain is related to distributed dextral simple shear associated with Pacific-North American plate motion. Paleomagnetic data show that clockwise rotation of the western Transverse Ranges has occurred along the southern boundary of the domain during the past 6 m.y. During this time, the Salinian crustal block, which forms the eastern boundary of the Los Osos domain, has remained relatively stable. Internal shortening of the Los Osos domain has accommodated the relative motions of these bordering crustal blocks, particularly the rotation of the western Transverse Ranges.

Fault segmentation: New concepts from the Wasatch Fault Zone, Utah, USA

USGS Publications Warehouse

Duross, Christopher; Personius, Stephen F.; Crone, Anthony J.; Olig, Susan S.; Hylland, Michael D.; Lund, William R.; Schwartz, David P.

2016-01-01

The question of whether structural segment boundaries along multisegment normal faults such as the Wasatch fault zone (WFZ) act as persistent barriers to rupture is critical to seismic hazard analyses. We synthesized late Holocene paleoseismic data from 20 trench sites along the central WFZ to evaluate earthquake rupture length and fault segmentation. For the youngest (<3 ka) and best-constrained earthquakes, differences in earthquake timing across prominent primary segment boundaries, especially for the most recent earthquakes on the north-central WFZ, are consistent with segment-controlled ruptures. However, broadly constrained earthquake times, dissimilar event times along the segments, the presence of smaller-scale (subsegment) boundaries, and areas of complex faulting permit partial-segment and multisegment (e.g., spillover) ruptures that are shorter (~20–40 km) or longer (~60–100 km) than the primary segment lengths (35–59 km). We report a segmented WFZ model that includes 24 earthquakes since ~7 ka and yields mean estimates of recurrence (1.1–1.3 kyr) and vertical slip rate (1.3–2.0 mm/yr) for the segments. However, additional rupture scenarios that include segment boundary spatial uncertainties, floating earthquakes, and multisegment ruptures are necessary to fully address epistemic uncertainties in rupture length. We compare the central WFZ to paleoseismic and historical surface ruptures in the Basin and Range Province and central Italian Apennines and conclude that displacement profiles have limited value for assessing the persistence of segment boundaries but can aid in interpreting prehistoric spillover ruptures. Our comparison also suggests that the probabilities of shorter and longer ruptures on the WFZ need to be investigated.

Faulted terrace risers place new constraints on the late Quaternary slip rate for the central Altyn Tagh fault, northwest Tibet

USGS Publications Warehouse

Gold, R.D.; Cowgill, E.; Arrowsmith, J.R.; Chen, X.; Sharp, W.D.; Cooper, K.M.; Wang, X.-F.

2011-01-01

The active, left-lateral Altyn Tagh fault defines the northwestern margin of the Tibetan Plateau in western China. To clarify late Quaternary temporal and spatial variations in slip rate along the central portion of this fault system (85??-90??E), we have more than doubled the number of dated offset markers along the central Altyn Tagh fault. In particular, we determined offset-age relations for seven left-laterally faulted terrace risers at three sites (Kelutelage, Yukuang, and Keke Qiapu) spanning a 140-km-long fault reach by integrating surficial geologic mapping, topographic surveys (total station and tripod-light detection and ranging [T-LiDAR]), and geochronology (radiocarbon dating of organic samples, 230Th/U dating of pedogenic carbonate coatings on buried clasts, and terrestrial cosmogenic radionuclide exposure age dating applied to quartz-rich gravels). At Kelutelage, which is the westernmost site (37.72??N, 86.67??E), two faulted terrace risers are offset 58 ?? 3 m and 48 ?? 4 m, and formed at 6.2-6.1 ka and 5.9-3.7 ka, respectively. At the Yukuang site (38.00??N, 87.87??E), four faulted terrace risers are offset 92 ?? 12 m, 68 ?? 6 m, 55 ?? 13 m, and 59 ?? 9 m and formed at 24.2-9.5 ka, 6.4-5.0 ka, 5.1-3.9 ka, and 24.2-6.4 ka, respectively. At the easternmost site, Keke Qiapu (38.08??N, 88.12??E), a faulted terrace riser is offset 33 ?? 6 m and has an age of 17.1-2.2 ka. The displacement-age relationships derived from these markers can be satisfied by an approximately uniform slip rate of 8-12 mm/yr. However, additional analysis is required to test how much temporal variability in slip rate is permitted by this data set. ?? 2011 Geological Society of America.

Exploring geothermal structures in the Ilan Plain, Taiwan

NASA Astrophysics Data System (ADS)

Wang, Chien-Ying; Shih, Ruey-Chan; Chung, Chen-Tung; Huang, Ming-Zi; Kuo, Hsuan-Yu

2017-04-01

The Ilan Plain in northeast Taiwan is located at the southwestern tip of the Okinawa Trough, which extends westward into the Taiwan orogeny. The Ilan Plain covered by thick sediments is clipped by the Hsuehshan Range in the northern side and the Central Range in the southern side. High geothermal gradients with plenteous hot springs of this area may result from igneous intrusion associated with the back-arc spreading of the Okinawa Trough. In this study, we use reflection seismic survey to explore underground structures in the whole Ilan Plain, especially in SanShin, Wujie, and Lize area. We aim to find the relationship between underground structures and geothermal forming mechanism. The research uses reflection seismic survey to investigate the high geothermal gradient area with two mini-vibrators and 240-channel system. The total length of seismic lines is more than 30 kilometers. The results show that alluvial sediments covering the area about 400 600 meters thick and then thin out to the west in SanShin area. In SanShin , the Taiyaqiao anticline in Hsuehshan Range has entered the plain area and is bounded by the Zhuoshui fault (south) and the Zailian fault (north). In Wujie and Lize , Zhuoshui fault cut through a strong reflector which is the top of the gravel layer near the bottom of the alluvial layer, while the SanShin fault seems to cut near very shallow strata. These two faults are a strike-slip fault with a bit of normal fault component distributing over a range of 600 meters. In Ilan Plain, the geothermal forming mechanism is controlled by anticlines and faults. The hydrothermal solution which migrates upward along these anticline or fault zones to the shallow part causing high geothermal gradients in these areas.

A fault-based model for crustal deformation, fault slip-rates and off-fault strain rate in California

USGS Publications Warehouse

Zeng, Yuehua; Shen, Zheng-Kang

2016-01-01

We invert Global Positioning System (GPS) velocity data to estimate fault slip rates in California using a fault‐based crustal deformation model with geologic constraints. The model assumes buried elastic dislocations across the region using Uniform California Earthquake Rupture Forecast Version 3 (UCERF3) fault geometries. New GPS velocity and geologic slip‐rate data were compiled by the UCERF3 deformation working group. The result of least‐squares inversion shows that the San Andreas fault slips at 19–22  mm/yr along Santa Cruz to the North Coast, 25–28  mm/yr along the central California creeping segment to the Carrizo Plain, 20–22  mm/yr along the Mojave, and 20–24  mm/yr along the Coachella to the Imperial Valley. Modeled slip rates are 7–16  mm/yr lower than the preferred geologic rates from the central California creeping section to the San Bernardino North section. For the Bartlett Springs section, fault slip rates of 7–9  mm/yr fall within the geologic bounds but are twice the preferred geologic rates. For the central and eastern Garlock, inverted slip rates of 7.5 and 4.9  mm/yr, respectively, match closely with the geologic rates. For the western Garlock, however, our result suggests a low slip rate of 1.7  mm/yr. Along the eastern California shear zone and southern Walker Lane, our model shows a cumulative slip rate of 6.2–6.9  mm/yr across its east–west transects, which is ∼1  mm/yr increase of the geologic estimates. For the off‐coast faults of central California, from Hosgri to San Gregorio, fault slips are modeled at 1–5  mm/yr, similar to the lower geologic bounds. For the off‐fault deformation, the total moment rate amounts to 0.88×1019  N·m/yr, with fast straining regions found around the Mendocino triple junction, Transverse Ranges and Garlock fault zones, Landers and Brawley seismic zones, and farther south. The overall California moment rate is 2.76×1019  N·m/yr, which is a 16% increase compared with the UCERF2 model.

Complex faulting associated with the 22 December 2003 Mw 6.5 San Simeon California, earthquake, aftershocks and postseismic surface deformation

USGS Publications Warehouse

McLaren, Marcia K.; Hardebeck, Jeanne L.; Van Der Elst, Nicholas; Unruh, Jeffrey R.; Bawden, Gerald W.; Blair, James Luke

2008-01-01

We use data from two seismic networks and satellite interferometric synthetic aperture radar (InSAR) imagery to characterize the 22 December 2003 Mw 6.5 San Simeon earthquake sequence. Absolute locations for the mainshock and nearly 10,000 aftershocks were determined using a new three-dimensional (3D) seismic velocity model; relative locations were obtained using double difference. The mainshock location found using the 3D velocity model is 35.704° N, 121.096° W at a depth of 9.7±0.7 km. The aftershocks concentrate at the northwest and southeast parts of the aftershock zone, between the mapped traces of the Oceanic and Nacimiento fault zones. The northwest end of the mainshock rupture, as defined by the aftershocks, projects from the mainshock hypocenter to the surface a few kilometers west of the mapped trace of the Oceanic fault, near the Santa Lucia Range front and the >5 mm postseismic InSAR imagery contour. The Oceanic fault in this area, as mapped by Hall (1991), is therefore probably a second-order synthetic thrust or reverse fault that splays upward from the main seismogenic fault at depth. The southeast end of the rupture projects closer to the mapped Oceanic fault trace, suggesting much of the slip was along this fault, or at a minimum is accommodating much of the postseismic deformation. InSAR imagery shows ∼72 mm of postseismic uplift in the vicinity of maximum coseismic slip in the central section of the rupture, and ∼48 and ∼45 mm at the northwest and southeast end of the aftershock zone, respectively. From these observations, we model a ∼30-km-long northwest-trending northeast-dipping mainshock rupture surface—called the mainthrust—which is likely the Oceanic fault at depth, a ∼10-km-long southwest-dipping backthrust parallel to the mainthrust near the hypocenter, several smaller southwest-dipping structures in the southeast, and perhaps additional northeast-dipping or subvertical structures southeast of the mainshock plane. Discontinuous backthrust features opposite the mainthrust in the southeast part of the aftershock zone may offset the relic Nacimiento fault zone at depth. The InSAR data image surface deformation associated with both aseismic slip and aftershock production on the mainthrust and the backthrusts at the northwest and southeast ends of the aftershock zone. The well-defined mainthrust at the latitude of the epicenter and antithetic backthrust illuminated by the aftershock zone indicate uplift of the Santa Lucia Range as a popup block; aftershocks in the southeast part of the zone also indicate a popup block, but it is less well defined. The absence of backthrust features in the central part of the zone suggests range-front uplift by fault-propagation folding, or backthrusts in the central part were not activated during the mainshock.

Translation vs. Rotation: The Battle for Accommodation of Dextral Shear at the Northern Terminus of the Central Walker Lane, Western Nevada

NASA Astrophysics Data System (ADS)

Carlson, C. W.; Faulds, J. E.

2014-12-01

Positioned between the Sierra Nevada microplate and Basin and Range in western North America, the Walker Lane (WL) accommodates ~20% of the dextral motion between the North American and Pacific plates on predominately NW-striking dextral and ENE to E-W-striking sinistral fault systems. The Terrill Mountains (TM) lie at the northern terminus of a domain of dextral faults accommodating translation of crustal-blocks in the central WL and at the southeast edge of sinistral faults accommodating oroclinal flexure and CW rotation of blocks in the northern WL. As the mechanisms of strain transfer between these disparate fault systems are poorly understood, the thick Oligocene to Pliocene volcanic strata of the TM area make it an ideal site for studying the transfer of strain between regions undergoing differing styles of deformation and yet both accommodating dextral shear. Detailed geologic mapping and paleomagnetic study of ash-flow tuffs in the TM region has been conducted to elucidate Neogene strain accommodation for this transitional region of the WL. Strain at the northernmost TM appears to be transferred from a system of NW-striking dextral faults to a system of ~E-W striking sinistral faults with associated CW flexure. A distinct ~23 Ma paleosol is locally preserved below the tuff of Toiyabe and provides an important marker bed. This paleosol is offset with ~6 km of dextral separation across the fault bounding the NE flank of the TM. This fault is inferred as the northernmost strand of the NW-striking, dextral Benton Spring fault system, with offset consistent with minimums constrained to the south (6.4-9.6 km, Gabbs Valley Range). Paleomagnetic results suggest counter-intuitive CCW vertical-axis rotation of crustal blocks south of the domain boundary in the system of NW-striking dextral faults, similar to some other domains of NW-striking dextral faults in the northern WL. This may result from coeval dextral shear and WNW-directed extension within the left-stepping system of dextral fault. The left steps are analogous to Riedel shears developing above a more through-going shear zone at depth. However, a site directly adjacent to the Benton Springs fault is rotated ~30° CW, likely due to fault drag. These results show the complex and important contribution of vertical-axis rotations in accommodation of dextral shear.

Fault creep and strain partitioning in Trinidad-Tobago: Geodetic measurements, models, and origin of creep

NASA Astrophysics Data System (ADS)

La Femina, P.; Weber, J. C.; Geirsson, H.; Latchman, J. L.; Robertson, R. E. A.; Higgins, M.; Miller, K.; Churches, C.; Shaw, K.

2017-12-01

We studied active faults in Trinidad and Tobago in the Caribbean-South American (CA-SA) transform plate boundary zone using episodic GPS (eGPS) data from 19 sites and continuous GPS (cGPS) data from 8 sites, then by modeling these data using a series of simple screw dislocation models. Our best-fit model for interseismic (interseimic = between major earthquakes) fault slip requires: 12-15 mm/yr of right-lateral movement and very shallow locking (0.2 ± 0.2 km; essentially creep) across the Central Range Fault (CRF); 3.4 +0.3/-0.2 mm/yr across the Soldado Fault in south Trinidad, and 3.5 +0.3/-0.2 mm/yr of dextral shear on fault(s) between Trinidad and Tobago. The upper-crustal faults in Trinidad show very little seismicity (1954-current from local network) and do not appear to have generated significant historic earthquakes. However, paleoseismic studies indicate that the CRF ruptured between 2710 and 500 yr. B.P. and thus it was recently capable of storing elastic strain. Together, these data suggest spatial and/or temporal fault segmentation on the CRF. The CRF marks a physical boundary between rocks associated with thermogenically generated petroleum and over-pressured fluids in south and central Trinidad, from rocks containing only biogenic gas to the north, and a long string of active mud volcanoes align with the trace of the Soldado Fault along Trinidad's south coast. Fluid (oil and gas) overpressure, as an alternative or in addition to weak mineral phases in the fault zone, may thus cause the CRF fault creep and the lack of seismicity that we observe.

Late Quaternary activity of the Ecemiş Fault Zone, Turkey; implications from cosmogenic 36Cl dating of offset alluvial fans

NASA Astrophysics Data System (ADS)

Akif Sarıkaya, Mehmet; Yıldırım, Cengiz; Çiner, Attila

2014-05-01

The Ecemiş Fault Zone is the southernmost segment of the Central Anatolian Fault Zone. The tectonic trough of the fault zone defines the boundary between the Central and Eastern Taurides Ranges. The presence of faulted alluvial fans and colluvium within this trough provide favorable conditions to unravel the Late Quaternary slip-rate of the fault zone by cosmogenic surface exposure dating. In this context, we focused on the main strand of the fault zone and also on the Cevizlik Fault that delimits the mountain front of the Aladaǧlar, Eastern Taurides. Geomorphic mapping and topographic surveying indicate four different alluvial fan levels deposited along the main strand. Our topographic survey reveals 60±5 m horizontal and 18±2 m vertical displacement of the oldest fan surface (AF1) associated with the main strand of the fault zone. We dated the surface of the AF1 with 13 cosmogenic 36Cl samples. Our results indicate that the AF1 surface was abandoned maximum 105.3±1.5 ka ago. Accordingly, we propose 0.57±0.05 mm/yr horizontal and 0.17±0.02 mm/yr vertical mean slip-rates since 100 ka for the main strand. On the other hand, we measured 20±2 m vertical displacement on the colluvium along the Cevizlik Fault. The surface exposure age of the colluvium yielded 21.9±0.3 ka that translates to 0.91±0.09 mm/yr vertical slip-rate for the Cevizlik Fault. Our results reveal significant Quaternary deformation, and low strain rates might indicate very long earthquake recurrence intervals along the fault zone.

The Point Sal–Point Piedras Blancas correlation and the problem of slip on the San Gregorio–Hosgri fault, central California Coast Ranges

USGS Publications Warehouse

Colgan, Joseph P.; Stanley, Richard G.

2016-01-01

Existing models for large-magnitude, right-lateral slip on the San Gregorio–Hosgri fault system imply much more deformation of the onshore block in the Santa Maria basin than is supported by geologic data. This problem is resolved by a model in which dextral slip on this fault system increases gradually from 0–10 km near Point Arguello to ∼150 km at Cape San Martin, but such a model requires abandoning the cross-fault tie between Point Sal and Point Piedras Blancas, which requires 90–100 km of right-lateral slip on the southern Hosgri fault. We collected stratigraphic and detrital zircon data from Miocene clastic rocks overlying Jurassic basement at both localities to determine if either section contained unique characteristics that could establish how far apart they were in the early Miocene. Our data indicate that these basins formed in the early Miocene during a period of widespread transtensional basin formation in the central Coast Ranges, and they filled with sediment derived from nearby pre-Cenozoic basement rocks. Although detrital zircon data do not indicate a unique source component in either section, they establish the maximum depositional age of the previously undated Point Piedras Blancas section to be 18 Ma. We also show that detrital zircon trace-element data can be used to discriminate between zircons of oceanic crust and arc affinity of the same age, a potentially useful tool in future studies of the California Coast Ranges. Overall, we find no characteristics in the stratigraphy and provenance of the Point Sal and Point Piedras Blancas sections that are sufficiently unique to prove whether they were far apart or close together in the early Miocene, making them of questionable utility as piercing points.

3-D GPR data analysis for high-resolution imaging of shallow subsurface faults: the Mt Vettore case study (Central Apennines, Italy)

NASA Astrophysics Data System (ADS)

Ercoli, Maurizio; Pauselli, Cristina; Frigeri, Alessandro; Forte, Emanuele; Federico, Costanzo

2014-07-01

The activation of Late Quaternary faults in the Central Apennines (Italy) could generate earthquakes with magnitude of about 6.5, and the Monte Vettore fault system probably belongs to the same category of seismogenetic faults. Such structure has been defined `silent', because of its geological and geomorphological evidences of past activation, but the absence of historical records in the seismic catalogues to be associated with its activation. The `Piano di Castelluccio' intramountain basin, resulting from the Quaternary activity of normal faults, is characterized by a secondary fault strand highlighted by a NW-SE fault scarp: it has been already studied through palaeoseismological trenches, which highlighted evidences of Quaternary shallow faulting due to strong earthquakes, and through a 2-D ground penetrating radar (GPR) survey, showing the first geophysical signature of faulting for this site. Within the same place, a 3-D GPR volume over a 20 × 20 m area has been collected. The collection of radar echoes in three dimensions allows to map both the vertical and lateral continuity of shallow geometries of the fault zone (Fz), imaging features with high resolution, ranging from few metres to centimetres and therefore imaging also local variations at the microscale. Several geophysical markers of faulting, already highlighted on this site, have been taken as reference to plan the 3-D survey. In this paper, we provide the first 3-D subsurface imaging of an active shallow fault belonging to the Umbria-Marche Apennine highlighting the subsurface fault geometry and the stratigraphic sequence up to a depth of about 5 m. From our data, geophysical faulting signatures are clearly visible in three dimensions: diffraction hyperbolas, truncations of layers, local attenuated zones and varying dip of the layers have been detected within the Fz. The interpretation of the 3-D data set provided qualitative and quantitative geological information in addition to the fault location, like its geometry, boundaries and an estimation of the fault throw.

The susitna glacier thrust fault: Characteristics of surface ruptures on the fault that initiated the 2002 denali fault earthquake

USGS Publications Warehouse

Crone, A.J.; Personius, S.F.; Craw, P.A.; Haeussler, P.J.; Staft, L.A.

2004-01-01

The 3 November 2002 Mw 7.9 Denali fault earthquake sequence initiated on the newly discovered Susitna Glacier thrust fault and caused 48 km of surface rupture. Rupture of the Susitna Glacier fault generated scarps on ice of the Susitna and West Fork glaciers and on tundra and surficial deposits along the southern front of the central Alaska Range. Based on detailed mapping, 27 topographic profiles, and field observations, we document the characteristics and slip distribution of the 2002 ruptures and describe evidence of pre-2002 ruptures on the fault. The 2002 surface faulting produced structures that range from simple folds on a single trace to complex thrust-fault ruptures and pressure ridges on multiple, sinuous strands. The deformation zone is locally more than 1 km wide. We measured a maximum vertical displacement of 5.4 m on the south-directed main thrust. North-directed backthrusts have more than 4 m of surface offset. We measured a well-constrained near-surface fault dip of about 19?? at one site, which is considerably less than seismologically determined values of 35??-48??. Surface-rupture data yield an estimated magnitude of Mw 7.3 for the fault, which is similar to the seismological value of Mw 7.2. Comparison of field and seismological data suggest that the Susitna Glacier fault is part of a large positive flower structure associated with northwest-directed transpressive deformation on the Denali fault. Prehistoric scarps are evidence of previous rupture of the Sustina Glacier fault, but additional work is needed to determine if past failures of the Susitna Glacier fault have consistently induced rupture of the Denali fault.

Segmentation of the Calaveras-Hayward Fault System Based on 3-D Geometry and Geology at Large-Earthquake Depth

NASA Astrophysics Data System (ADS)

Graymer, R. W.; Simpson, R. W.; Jachens, R. C.; Ponce, D. A.; Phelps, G. A.; Watt, J. T.; Wentworth, C. M.

2007-12-01

For the purpose of estimating seismic hazard, the Calaveras and Hayward Faults have been considered as separate structures and analyzed and segmented based largely on their surface-trace geometry and the extent of the 1868 Hayward Fault earthquake. Recent relocations of earthquakes and 3-D geologic mapping have shown, however, that at depths associated with large earthquakes (>5 km) the fault geology and geometry is quite different than that at the surface. Using deep fault geometry inferred from these studies we treat the Hayward and Calaveras Faults as a single system and divide the system into segments that differ from the previously accepted segments as follows: 1. The Hayward Fault connects directly to the central Calaveras Fault at depth, as opposed to the 5 km wide restraining stepover zone of multiple imbricate oblique right-lateral reverse faults at the surface east of Fremont and San Jose (between about 37.25°-37.6°N). 2. The segment boundary between the Hayward, central Calaveras, and northern Calaveras is based on their Y- shaped intersection at depth near 37.40°N, 121.76°W (Cherry Flat Reservoir), about 8 km south of the previously accepted central-northern Calaveras Fault segment boundary. 3. The central Calaveras Fault is divided near 37.14°N, 121.56°W (southern end of Anderson Lake) into two subsegments based on a large discontinuity at depth seen in relocated seismicity. 4. The Hayward Fault is divided near 37.85°N, 122.23°W (Lake Temescal) into two segments based on a large contrast in fault face geology. This segmentation is similar to that based on the extent of 1868 fault rupture, but is now related to an underlying geologic cause. The direct connection of the Hayward and central Calaveras Faults at depth suggests that earthquakes larger than those previously modeled should be considered (~M6.9 for the southern Hayward, ~M7.2 for the southern Hayward plus northern central Calaveras). A NEHRP study by Witter and others (2003; NEHRP 03HQGR0098) suggested evidence for large surface ruptures on the northern central Calaveras, but that work is not peer-reviewed and there is little or no other paleoseismic or geodetic data from the stepover zone or northern central Calaveras Fault (all commonly cited data are from the southern central Calaveras Fault), so the sparse surface data neither demands nor precludes our interpretation. The additional segmentation of the central Calaveras Fault proposed here may explain the observation that this segment seems to generate characteristic moderate (~M6.0-6.5) earthquakes rather than the larger ~M6.9 earthquakes that could be generated by rupture of the previously defined longer central Calaveras segment. Better information regarding fault plane geometry and 3-D distribution of rock properties adjacent to the faults at seismogenic depths should help us revise proposed segmentation models of other faults for seismic hazard analyses.

Late Quaternary slip rate determination by CRN dating on the Haiyuan fault, China, and implication for complex geometry fault systems

NASA Astrophysics Data System (ADS)

Matrau, Rémi; Klinger, Yann; Van der Woerd, Jérôme; Liu-Zeng, Jing; Li, Zhanfei; Xu, Xiwei

2017-04-01

Late Quaternary slip rate determination by CRN dating on the Haiyuan fault, China, and implication for complex geometry fault systems Matrau Rémi, Klinger Yann, Van der Woerd Jérôme, Liu-Zeng Jing, Li Zhanfei, Xu Xiwei The Haiyuan fault in Gansu Province, China, is a major left-lateral strike-slip fault forming the northeastern boundary of the Tibetan plateau and accommodating part of the deformation from the India-Asia collision. Geomorphic and geodetic studies of the Haiyuan fault show slip rates ranging from 4 mm/yr to 19 mm/yr from east to west along 500 km of the fault. Such discrepancy could be explained by the complex geometry of the fault system, leading to slip distribution on multiple branches. Combining displacement measurements of alluvial terraces from high-resolution Pléiades images and 10Be - 26Al cosmogenic radionuclides (CRN) dating, we bracket the late Quaternary slip rate along the Hasi Shan fault segment (37°00' N, 104°25' E). At our calibration site, terrace riser offsets for 5 terraces ranging from 6 m to 227 m and CRN ages ranging from 6.5±0.6 kyr to 41±4 kyr - yield geological left-lateral slip rates from 2.0 mm/yr to 4.4 mm/yr. We measured consistent terrace riser offset values along the entire 25 km-long segment, which suggests that some external forcing controls the regional river-terrace emplacement, regardless of each specific catchment. Hence, we extend our slip rate determination to the entire Hasi Shan fault segment to be 4.0±1.0 mm/yr since the last 40 kyr. This rate is consistent with other long-term rates of 4 mm/yr to 5 mm/yr east and west of Hasi Shan - as well as geodetic rates of 4 mm/yr to 6 mm/yr west of Hasi Shan. However, Holocene terraces and moraines offsets have suggested higher rates of 15 to 20 mm/yr further west. Such disparate rates may be explained by slip distribution on multiple branches. In particular, the Zhongwei fault splay in the central part of the Haiyuan fault, with a slip rate of 4-5 mm/yr could partly explain the faster rates on the western single stranded Haiyuan fault. In addition we constrained 0.55±0.1 mm/yr of uplift rate along the Hasi Shan, where the fault strike veers southward, indicating slip partitioning. Our slip rate along the Hasi Shan segment is consistent with most of the long-term and short-term slip rates ( 5 mm/yr) measured along the central and eastern parts of the Haiyuan fault. However the discrepancy with other studies to the west highlights the major implication of complex geometries on the slip distribution over large fault systems.

Asymmetric Exhumation Patterns Revealed through Apatite-Zircon Thermochronology of the Santa Lucia Range, Central California

NASA Astrophysics Data System (ADS)

Mere, A.; Steely, A.; Hourigan, J. K.

2016-12-01

Previous thermochronological analyses of crystalline bedrock in the central Santa Lucia range have yielded surprisingly rapid rates of surface uplift and bedrock extrusion despite lack of modern seismicity along nearby faults. We use 8 new apatite and zircon (U-Th)/He dates in order to better constrain the history of bedrock extrusion in response to the transpressional North American-Pacific plate boundary. Granitic samples were collected along coastal fault blocks bounded by the Palo Colorado (PCF), Sur-Nacimiento (SNF), and San Gregorio Hosgri faults (SGHF); as well as one sample from Salinian Basement >25km NE of the SGHF. Helium was extracted and analyzed using a quadrupole equipped multi-sample laser microfurnace and U/Th content was measured using high precision isotope-dilution ICP mass spectrometry. Rapid late Cretaceous unroofing is captured in Salinian basement zircon and apatite by the respective 67Ma and 63Ma dates. Zircon along coastal silvers proximal to PCF and SNF record 28-31Ma dates while zircon in close proximity to SGHF record ages as young as 6.5Ma. Apatite ages proximal to PCF and SNF range between 6-9Ma and are as young as 1.5Ma directly NE of the SGHF. These data reflect increased exhumation beginning as recently as the Miocene and additionally indicate rates of modern (<2Ma) uplift exceeding 1.3 mm/yr. These results indicate that stresses caused by the active plate boundary are accommodated by the SGHF and associated faults as vertical deformation despite low rates of modern seismicity. We suggest that the SGHF and nearby faults are more active, or behave differently, that previously acknowledged. The pattern of focused exhumation within narrow fault blocks appears to be related to underplating of low strength schist that is thought to be synchronous with late Cretaceous unroofing of Salinian basement.

Recent crustal movements in the Sierra Nevada-Walker lane region of California-Nevada: Part i, rate and style of deformation

USGS Publications Warehouse

Slemmons, D.B.; Wormer, D.V.; Bell, E.J.; Silberman, M.L.

1979-01-01

This review of geological, seismological, geochronological and paleobotanical data is made to compare historic and geologic rates and styles of deformation of the Sierra Nevada and western Basin and Range Provinces. The main uplift of this region began about 17 m.y. ago, with slow uplift of the central Sierra Nevada summit region at rates estimated at about 0.012 mm/yr and of western Basin and Range Province at about 0.01 mm/yr. Many Mesozoic faults of the Foothills fault system were reactivated with normal slip in mid-Tertiary time and have continued to be active with slow slip rates. Sparse data indicate acceleration of rates of uplift and faulting during the Late Cenozoic. The Basin and Range faulting appears to have extended westward during this period with a reduction in width of the Sierra Nevada. The eastern boundary zone of the Sierra Nevada has an irregular en-echelon pattern of normal and right-oblique faults. The area between the Sierra Nevada and the Walker Lane is a complex zone of irregular patterns of ho??rst and graben blocks and conjugate normal-to right- and left-slip faults of NW and NE trend, respectively. The Walker Lane has at least five main strands near Walker Lake, with total right-slip separation estimated at 48 km. The NE-trending left-slip faults are much shorter than the Walker Lane fault zone and have maximum separations of no more than a few kilometers. Examples include the 1948 and 1966 fault zone northeast of Truckee, California, the Olinghouse fault (Part III) and possibly the almost 200-km-long Carson Lineament. Historic geologic evidence of faulting, seismologic evidence for focal mechanisms, geodetic measurements and strain measurements confirm continued regional uplift and tilting of the Sierra Nevada, with minor internal local faulting and deformation, smaller uplift of the western Basin and Range Province, conjugate focal mechanisms for faults of diverse orientations and types, and a NS to NE-SW compression axis (??1) and an EW to NW-SE extension axis (??3). ?? 1979.

Active simultaneous uplift and margin-normal extension in a forearc high, Crete, Greece

NASA Astrophysics Data System (ADS)

Gallen, S. F.; Wegmann, K. W.; Bohnenstiehl, D. R.; Pazzaglia, F. J.; Brandon, M. T.; Fassoulas, C.

2014-07-01

The island of Crete occupies a forearc high in the central Hellenic subduction zone and is characterized by sustained exhumation, surface uplift and extension. The processes governing orogenesis and topographic development here remain poorly understood. Dramatic topographic relief (2-6 km) astride the southern coastline of Crete is associated with large margin-parallel faults responsible for deep bathymetric depressions known as the Hellenic troughs. These structures have been interpreted as both active and inactive with either contractional, strike-slip, or extensional movement histories. Distinguishing between these different structural styles and kinematic histories here allows us to explore more general models for improving our global understanding of the tectonic and geodynamic processes of syn-convergent extension. We present new observations from the south-central coastline of Crete that clarifies the role of these faults in the late Cenozoic evolution of the central Hellenic margin and the processes controlling Quaternary surface uplift. Pleistocene marine terraces are used in conjunction with optically stimulated luminesce dating and correlation to the Quaternary eustatic curve to document coastal uplift and identify active faults. Two south-dipping normal faults are observed, which extend offshore, offset these marine terrace deposits and indicate active N-S (margin-normal) extension. Further, marine terraces preserved in the footwall and hanging wall of both faults demonstrate that regional net uplift of Crete is occurring despite active extension. Field mapping and geometric reconstructions of an active onshore normal fault reveal that the subaqueous range-front fault of south-central Crete is synthetic to the south-dipping normal faults on shore. These findings are inconsistent with models of active horizontal shortening in the upper crust of the Hellenic forearc. Rather, they are consistent with topographic growth of the forearc in a viscous orogenic wedge, where crustal thickening and uplift are a result of basal underplating of material that is accompanied by extension in the upper portions of the wedge. Within this framework a new conceptual model is presented for the late Cenozoic vertical tectonics of the Hellenic forearc.

Evidence for large-magnitude, post-Eocene extension in the northern Shoshone Range, Nevada, and its implications for Carlin-type gold deposits in the lower plate of the Roberts Mountains allochthon

USGS Publications Warehouse

Colgan, Joseph P.; Henry, Christopher D.; John, David A.

2014-01-01

The northern Shoshone and Toiyabe Ranges in north-central Nevada expose numerous areas of mineralized Paleozoic rock, including major Carlin-type gold deposits at Pipeline and Cortez. Paleozoic rocks in these areas were previously interpreted to have undergone negligible postmineralization extension and tilting, but here we present new data that suggest major post-Eocene extension along west-dipping normal faults. Tertiary rocks in the northern Shoshone Range crop out in two W-NW–trending belts that locally overlie and intrude highly deformed Lower Paleozoic rocks of the Roberts Mountains allochthon. Tertiary exposures in the more extensive, northern belt were interpreted as subvertical breccia pipes (intrusions), but new field data indicate that these “pipes” consist of a 35.8 Ma densely welded dacitic ash flow tuff (informally named the tuff of Mount Lewis) interbedded with sandstones and coarse volcaniclastic deposits. Both tuff and sedimentary rocks strike N-S and dip 30° to 70° E; the steeply dipping compaction foliation in the tuffs was interpreted as subvertical flow foliation in breccia pipes. The southern belt along Mill Creek, previously mapped as undivided welded tuff, includes the tuff of Cove mine (34.4 Ma) and unit B of the Bates Mountain Tuff (30.6 Ma). These tuffs dip 30° to 50° east, suggesting that their west-dipping contacts with underlying Paleozoic rocks (previously mapped as depositional) are normal faults. Tertiary rocks in both belts were deposited on Paleozoic basement and none appear to be breccia pipes. We infer that their present east tilt is due to extension on west-dipping normal faults. Some of these faults may be the northern strands of middle Miocene (ca. 16 Ma) faults that cut and tilted the 34.0 Ma Caetano caldera ~40° east in the central Shoshone Range (

Micro-seismicity and seismotectonic study in Western Himalaya-Ladakh-Karakoram using local broadband seismic data

NASA Astrophysics Data System (ADS)

Kanna, Nagaraju; Gupta, Sandeep; Prakasam, K. S.

2018-02-01

We document the seismic activity and fault plane solutions (FPSs) in the Western Himalaya, Ladakh and Karakoram using data from 16 broadband seismographs operated during June 2002 to December 2003. We locate 206 earthquakes with a local magnitude in the range of 1.5 to 4.9 and calculate FPSs of 19 selected earthquakes based on moment tensor solutions. The earthquakes are distributed throughout the study region and indicate active tectonics in this region. The observed seismicity pattern is quite different than a well-defined pattern of seismicity, along the Main Central Thrust zone, in the eastern side of the study region (i.e., Kumaon-Garhwal Himalaya). In the Himalaya region, the earthquakes are distributed in the crust and upper mantle, whereas in the Ladakh-Karakoram area the earthquakes are mostly confined up to crustal depths. The fault plane solutions show a mixture of thrust, normal and strike-slip type mechanisms, which are well corroborated with the known faults/tectonics of the region. The normal fault earthquakes are observed along the Southern Tibet Detachment, Zanskar Shear Zone, Tso-Morari dome, and Kaurik-Chango fault; and suggest E-W extension tectonics in the Higher and Tethys Himalaya. The earthquakes of thrust mechanism with the left-lateral strike-slip component are seen along the Kistwar fault. The right-lateral strike-slip faulting with thrust component along the bending of the Main Boundary Thrust and Main Central Thrust shows the transpressional tectonics in this part of the Himalaya. The observed earthquakes with right-lateral strike-slip faulting indicate seismically active nature of the Karakoram fault.

Palinspastic reconstruction of southeastern California and southwestern Arizona for the middle Miocene

NASA Technical Reports Server (NTRS)

Richard, Stephen M.

1992-01-01

A paleogeographic reconstruction of southeastern California and southwestern Arizona at 10 Ma was made based on available geologic and geophysical data. Clockwise rotation of 39 deg was reconstructed in the eastern Transverse Ranges, consistent with paleomagnetic data from late Miocene volcanic rocks, and with slip estimates for left-lateral faults within the eastern Transverse Ranges and NW-trending right lateral faults in the Mojave Desert. This domain of rotated rocks is bounded by the Pinto Mountain fault on the north. In the absence of evidence for rotation of the San Bernardino Mountains or for significant right slip faults within the San Bernardino Mountains, the model requires that the late Miocene Pinto Mountain fault become a thrust fault gaining displacement to the west. The Squaw Peak thrust system of Meisling and Weldon may be a western continuation of this fault system. The Sheep Hole fault bounds the rotating domain on the east. East of this fault an array of NW-trending right slip faults and south-trending extensional transfer zones has produced a basin and range physiography while accumulating up to 14 km of right slip. This maximum is significantly less than the 37.5 km of right slip required in this region by a recent reconstruction of the central Mojave Desert. Geologic relations along the southern boundary of the rotating domain are poorly known, but this boundary is interpreted to involve a series of curved strike slip faults and non-coaxial extension, bounded on the southeast by the Mammoth Wash and related faults in the eastern Chocolate Mountains. Available constraints on timing suggest that Quaternary movement on the Pinto Mountain and nearby faults is unrelated to the rotation of the eastern Transverse Ranges, and was preceded by a hiatus during part of Pliocene time which followed the deformation producing the rotation. The reconstructed Clemens Well fault in the Orocopia Mountains, proposed as a major early Miocene strand of the San Andreas fault, projects eastward towards Arizona, where early Miocene rocks and structures are continuous across its trace. The model predicts a 14 deg clockwise rotation and 55 km extension along the present trace of the San Andreas fault during late Miocene and early Pliocene time. Palinspastic reconstructions of the San Andreas system based on this proposed reconstruction may be significantly modified from current models.

Structure and deformation history of the northern range of Trinidad and adjacent areas

NASA Astrophysics Data System (ADS)

Algar, S. T.; Pindell, J. L.

1993-08-01

Conflicting models have been proposed for both the evolution of northern South America and the neotectonics of the south Caribbean plate boundary zone. The Trinidadian portion of the margin is particularly controversial, but surprisingly it has been little studied. We present a structural analysis of Trinidad's Northern Range, pertinent updates of the island's stratigraphy and sedimentology, and new zircon fission track age determinations, and use them to constrain Trinidad's geologic history, and to better understand the controlling tectonic processes. In our interpretation Trinidad's three E-ENE striking ranges, which are separated by late Neogene-Recent depocenters, expose (1) the Northern Range Group, generally greenschist-metamorphosed Upper Jurassic to Cretaceous north facing continental slope sediments of the Northern Range, deposited on the northern South American passive margin 200-400 km to the WNW, and (2) the Trinidad Group, Cretaceous-Paleogene shelf slope sediments of the central and southern Trinidad deposited less than 100 km WNW of their present location. A small allochthon composing the Sans Souci Group Cretaceous tholeiitic volcaniclastic, basaltic, and gabbroic rocks (Sans Souci Formation) and sediments (Toco Formation) now in the northeastern Northern Range, has been transported hundreds of kilometers from the west with the Caribbean Plate. Despite earlier references to Cretaceous orogenesis, all deformation in Trinidad is of Cenozoic age. The first deformation in the Northern Range (D1) formed north vergent nappes and induced greenschist metamorphism, probably in the Late Eocene or Oligocene. The nappes developed either by the underthrusting of the Proto-Caribbean crust beneath South America due to convergence between North and South America, or as gravity slides caused by oversteepening induced by this convergence and/or the passage of the Caribbean Plate's peripheral bulge and arrival of its foredeep. Northern Range D2 deformation is south vergent and represents the incorporation of Northern Range metasediments into the Caribbean accretionary prism. The transition to D3 brittle transpressive right-lateral strike-slip faulting is interpreted to be due to the uplift and east-southeastward transpressive emplacement of Northern Range/Caribbean prism rocks onto the South American stepped shelf. This emplacement formed the Miocene transpressive thrust belts and foreland basin in central and southern Trinidad. In the final phase of Northern Range deformation (D4) ˜E-W normal faults and shear zones and conjugate NNW-SSE and NE-SW normal faults developed, and displacement on preexisting ˜E-W right-lateral strike-slip faults continued. The 11 Ma Northern Range zircon fission track ages suggest rapid uplift from the Late Miocene to Recent. Late Miocene subsidence of the Tobago platform immediately to the north of the Northern Range, and greater than 3 km of normal, down to the north, displacement indicated for the North Coast Fault Zone separating the Northern Range and Tobago platform, leads us to postulate that the rapid uplift of the Northern Range was in response to the northward detachment of the Tobago platform from above the Northern Range, along the north-dipping transtensional North Coast Fault Zone. This Late Miocene change in deformation style can be explained by a change from Caribbean/South American right-lateral transpression to right-lateral strike-slip generally striking 080°. This has generally induced a component of extension on pre-existing faults striking at greater than 080°, and a component of compression on faults striking at less than 080°.

Geophysical investigation of the Denali fault and Alaska Range orogen within the aftershock zone of the October-November 2002, M = 7.9 Denali fault earthquake

USGS Publications Warehouse

Fisher, M.A.; Nokleberg, W.J.; Ratchkovski, N.A.; Pellerin, L.; Glen, J.M.; Brocher, T.M.; Booker, J.

2004-01-01

The aftershock zone of the 3 November 2002, M = 7.9 earthquake that ruptured along the right-slip Denali fault in south-central Alaska has been investigated by using gravity and magnetic, magnetotelluric, and deep-crustal, seismic reflection data as well as outcrop geology and earthquake seismology. Strong seismic reflections from within the Alaska Range orogen north of the Denali fault dip as steeply as 25°N and extend to depths as great as 20 km. These reflections outline a relict crustal architecture that in the past 20 yr has produced little seismicity. The Denali fault is nonreflective, probably because this fault dips steeply to vertical. The most intriguing finding from geophysical data is that earthquake aftershocks occurred above a rock body, with low electrical resistivity (>10 Ω·m), that is at depths below ∼10 km. Aftershocks of the Denali fault earthquake have mainly occurred shallower than 10 km. A high geothermal gradient may cause the shallow seismicity. Another possibility is that the low resistivity results from fluids, which could have played a role in locating the aftershock zone by reducing rock friction within the middle and lower crust.

Rock Geochemistry and Mineralogy from Fault Zones and Polymetallic Fault Veins of the Central Front Range, Colorado

USGS Publications Warehouse

Caine, Jonathan S.; Bove, Dana J.

2010-01-01

During the 2004 to 2008 field seasons, approximately 200 hand samples of fault and polymetallic vein-related rocks were collected for geochemical and mineralogical analyses. The samples were collected by the U.S. Geological Survey as part of the Evolution of Brittle Structures Task under the Central Colorado Assessment Project (CCAP) of the Mineral Resources Program (http://minerals.cr.usgs.gov/projects/colorado_assessment/index.html). The purpose of this work has been to characterize the relation between epithermal, polymetallic mineral deposits, paleostress, and the geological structures that hosted fluid flow and localization of the deposits. The data in this report will be used to document and better understand the processes that control epithermal mineral-deposit formation by attempting to relate the geochemistry of the primary structures that hosted hydrothermal fluid flow to their heat and fluid sources. This includes processes from the scale of the structures themselves to the far field scale, inclusive of the intrusive bodies that have been thought to be the sources for the hydrothermal fluid flow. The data presented in this report are part of a larger assessment effort on public lands. The larger study area spans the region of the southern Rocky Mountains in Colorado from the Wyoming to New Mexico borders and from the eastern boundary of the Front Range to approximately the longitude of Vail and Leadville, Colorado. Although the study area has had an extensive history of geological mapping, the mapping has resulted in a number of hypotheses that are still in their infancy of being tested. For example, the proximity of polymetallic veins to intrusive bodies has been thought to reflect a genetic relation between the two features; however, this idea has not been well tested with geochemical indicators. Recent knowledge regarding the coupled nature of stress, strain, fluid flow, and geochemistry warrant new investigations and approaches to test a variety of ideas regarding the genetic processes associated with ore-deposit formation. The central part of the eastern Front Range has excellent exposures of fault zones and polymetallic fault veins, subsequently resulting in some of the most detailed mapping and associated data sets in the region. Thus, the area was chosen for detailed data compilation, new sample and data collection, and a variety of structural and geochemical analyses. The data presented in this report come from samples of fault-related exposures in the Front Range and include elemental chemistry and mineralogy from the outcrop-scale study localities within the larger CCAP study area.

Bedrock geologic map of the northern Alaska Peninsula area, southwestern Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Blodgett, Robert B.; Blome, Charles D.; Mohadjer, Solmaz; Preller, Cindi C.; Klimasauskas, Edward P.; Gamble, Bruce M.; Coonrad, Warren L.

2017-03-03

The northern Alaska Peninsula is a region of transition from the classic magmatic arc geology of the Alaska Peninsula to a Proterozoic and early Paleozoic carbonate platform and then to the poorly understood, tectonically complex sedimentary basins of southwestern Alaska. Physiographically, the region ranges from the high glaciated mountains of the Alaska-Aleutian Range to the coastal lowlands of Cook Inlet on the east and Bristol Bay on the southwest. The lower Ahklun Mountains and finger lakes on the west side of the map area show strong effects from glaciation. Structurally, a number of major faults cut the map area. Most important of these are the Bruin Bay Fault that parallels the coast of Cook Inlet, the Lake Clark Fault that cuts diagonally northeast to southwest across the eastern part of the map area, and the presently active Holitna Fault to the northwest that cuts surficial deposits.Distinctive rock packages assigned to three provinces are overlain by younger sedimentary rocks and intruded by widely dispersed latest Cretaceous and (or) early Tertiary granitic rocks. Much of the east half of the map area lies in the Alaska-Aleutian Range province; the Jurassic to Tertiary Alaska-Aleutian Range batholith and derivative Jurassic sedimentary rocks form the core of this province, which is intruded and overlain by the Aleutian magmatic arc. The Lime Hills province, the carbonate platform, occurs in the north-central part of the map area. The Paleozoic and Mesozoic Ahklun Mountains province in the western part of the map area includes abundant chert, argillite, and graywacke and lesser limestone, basalt, and tectonic mélange. The Kuskokwim Group, an Upper Cretaceous turbidite sequence, is extensively exposed and bounds all three provinces in the west-central part of the map area.

Neotectonics of interior Alaska and the late Quaternary slip rate along the Denali fault system

USGS Publications Warehouse

Haeussler, Peter J.; Matmon, Ari; Schwartz, David P.; Seitz, Gordon G.

2017-01-01

The neotectonics of southern Alaska (USA) are characterized by a several hundred kilometers–wide zone of dextral transpressional that spans the Alaska Range. The Denali fault system is the largest active strike-slip fault system in interior Alaska, and it produced a Mw 7.9 earthquake in 2002. To evaluate the late Quaternary slip rate on the Denali fault system, we collected samples for cosmogenic surface exposure dating from surfaces offset by the fault system. This study includes data from 107 samples at 19 sites, including 7 sites we previously reported, as well as an estimated slip rate at another site. We utilize the interpreted surface ages to provide estimated slip rates. These new slip rate data confirm that the highest late Quaternary slip rate is ∼13 mm/yr on the central Denali fault near its intersection with the eastern Denali and the Totschunda faults, with decreasing slip rate both to the east and west. The slip rate decreases westward along the central and western parts of the Denali fault system to 5 mm/yr over a length of ∼575 km. An additional site on the eastern Denali fault near Kluane Lake, Yukon, implies a slip rate of ∼2 mm/yr, based on geological considerations. The Totschunda fault has a maximum slip rate of ∼9 mm/yr. The Denali fault system is transpressional and there are active thrust faults on both the north and south sides of it. We explore four geometric models for southern Alaska tectonics to explain the slip rates along the Denali fault system and the active fault geometries: rotation, indentation, extrusion, and a combination of the three. We conclude that all three end-member models have strengths and shortcomings, and a combination of rotation, indentation, and extrusion best explains the slip rate observations.

New Structural Interpretation of the Central Confusion Range, Western Utah, Based On Balanced Cross Sections

NASA Astrophysics Data System (ADS)

Yezerski, D.; Greene, D. C.

2009-12-01

The Confusion Range is a topographically low mountain range in the Basin and Range of west-central Utah, located east of and in the hanging wall of the Snake Range core complex. Previous workers have used a gravity sliding model to interpret the Confusion Range as a large structural trough or synclinorium (e.g. Hose, 1977). Based on existing mapping (Hose, 1965; Hintze, 1974) and new field data, we use balanced and restored cross sections to reinterpret the structure of the Confusion Range as an east-vergent fold-and-thrust belt formed during the Sevier Orogeny. The Confusion Range consists of Cambro-Ordovician through Triassic strata, with predominantly thick-bedded, competent carbonate rocks in the lower Paleozoic (lPz) section and incompetent shales and thin-bedded carbonates in the upper Paleozoic (uPz) section. The contrasting mechanical behavior of these stratigraphic sections results in faulted folds within uPz carbonates above detachments in shale-rich units, deforming in response to ramp-flat thrust faulting of the underlying lPz units. East of the axis of the Conger Mountain (Mtn) syncline, we attribute the increase in structural elevation of lPz rocks to a subsurface thrust sheet consisting of lPz strata that advanced eastward via a high-angle ramp from a lower detachment in the Kanosh Shale to an upper detachment in the Pilot Shale. The doubling of lPz strata that resulted continues through the eastern Confusion Range where a series of small-displacement thrust faults comprising the Kings Canyon thrust system gently tilt strata to the west. In the Conger Range, west of the Conger Mtn syncline, our analysis focuses on reinterpreting the geometrically unlikely folding depicted in previous cross sections as more admissible, fault-cored, asymmetric, detached folding. In our interpretation, resistance created by a steeply-dipping thrust ramp in the lPz section west of Conger Mtn resulted in folding of uPz strata into an east-vergent anticline. Continued east-vergent contraction against the ramp resulted in the west-dipping limb of the anticline, consisting of Ely Limestone, developing into an overturned, west-vergent, synclinal backfold detached in the Chainman Shale. Further contraction exceeded the fold capacity of the detachment fold and resulted in the formation of the Browns Wash fault as an east-vergent thrust fault. The Browns Wash fault is a key component in the development of the present structural geometry, emplacing a west-vergent overturned syncline (detachment fold) in the hanging wall against an east-vergent overturned syncline (footwall syncline) in the footwall. Further west, underlying the western Conger Range and Buckskin Hills, lPz strata are exposed in what we interpret to be a ramp anticline overlying a subsurface thrust ramp. This interpretation implies a lateral ramp separating lPz rocks in the Buckskin Hills from uPz rocks exposed in the Knoll Hill anticline to the north. UPz and Mesozoic strata exposed to the west on the edge of Snake Valley were emplaced by a Tertiary west-dipping normal fault that truncated the west limb of the ramp anticline.

Paleoseismological History of the Acambay Graben (Central Mexico)

NASA Astrophysics Data System (ADS)

Lacan, P.; Zúñiga, R.; Ortuño, M.; Persaud, M.; Aguirre-Diaz, G. J.; Langridge, R. M.; Villamor, P.; Perea, H.; Štěpančíková, P.; Carreon, D.; Cerca, M.; Suñe Puchol, I.; Corominas Calvet, O.; Audin, L.; Baize, S.; Lawton, T. F.; Rendón, A.

2013-12-01

The Acambay graben is part of the Trans-Mexican Volcanic Belt (TMVB) which strikes ESE-WNW across central Mexico, where the major part of the Mexican population is concentrated. The TMVB is an active, calc-alkaline volcanic arc that is related to the subduction of the Rivera and Cocos plates underneath the North American plate. The TMVB contains a series of intra-arc basins that form the Chapala-Tula fault zone (450 km long, 50 km wide). One of these extensive basins, the Acambay graben, is 80 km long and 15 to 30 km wide. It is limited north by the E-W striking Epitacio-Huerta (EHF) and Acambay-Tixmadejé normal faults and south by the Venta de Bravo (VBF) and the Pastores faults (PF) in the south. Other minor active faults are located within the basin, along the axis of the Graben. In the area, the instrumental seismicity is low to moderate, although one major historical earthquake (Ms = 6.9 Acambay event) occurred on November 19, 1912, causing widespread damage. In the last decade, our group has focused on the neotectonic and paleoseismological study of the major faults of the Acambay graben. More than 30 trenches have been dug at 15 sites in order to interpret the paleoseismological history of 7 major faults of the graben. In addition to paleoseismological trench studies, tectonic geomorphology, subsurface geophysics and micro topographic surveys have been used to assess the rupture history. All of the studied faults have to be considered as active faults, with a minimum of 2 to 5 paleoseismic events on each fault during the last 20 ka. Each fault rupture corresponds to a vertical displacement ranging from 1 to 150 centimetres. Considering the size of the observed displacements and the length of active segments, we demonstrate that large earthquakes with magnitude higher than 7 have occurred along some of these faults. Based on paleoseismological results, we calculate a major earthquake recurrence interval ranging from 2,000 to 5,000 years over a time span (~20 ka). These recurrence values overpass the Mexican historical seismicity catalogue that incorporates no more than the last 500 years. This suggests that most of the faults of the TMVB may be active despite the lack of known historical destructive events and could be able to produce earthquakes with serious consequences in the most populated area of Mexico.

A High-Resolution Seismic Survey Across the State Line fault, NV

NASA Astrophysics Data System (ADS)

Beachly, M.; Cox, C. M.; Saldana, S. C.; Snelson, C. M.; Taylor, W. J.; Robins, C.; Davis, R.; Stropky, M.; Phillips, R.; Cothrun, C.

2007-12-01

During the summer of 2007, an investigation of the faulting in Stewart Valley was under taken, located within the central Basin and Range province ~90 km west of Las Vegas, Nevada. The goal of this study was to resolve the seismic hazard potential of the State Line fault, a right-lateral strike-slip fault that runs the length of Stewart Valley. Four seismic reflection lines were acquired, two perpendicular and two parallel to the State Line fault. What is presented is an analysis of the western and eastern seismic lines parallel to the State Line fault. The western line was acquired utilizing a 144-channel geode system with each of the 4.5 Hz vertical geophones set out at 5 m intervals to form a 715 m long profile. The eastern line employed 120 of these geophones in a 595 m long profile. A mini-vibroseis served as the seismic source every ten meters, between geophones. The vibroseis was programmed to produce an 8 s linear sweep from 20-160 Hz. Three sweeps were recorded at each shot location without acquisition filters at a sampling rate of 0.5 ms. The three shot gathers were then stacked at each location to reduce noise. The data collected had minimal noise, although; during the processing of the eastern line a notch filtered was used to remove the 60 Hz noise created by adjacent power line. These lines, acquired parallel to the State Line fault, contain matching features that serve to determine how much lateral displacement the fault has undergone. The amount of the displacement can indicate how active the fault is, and thus, what magnitude of earthquake can be expected in the future. This will in turn contribute to determining the seismic hazard potential for southern Nevada. A preliminary interpretation of the seismic reflection sections indicates an average displacement of about 20 - 38 m with greater displacement in the deeper sections of the image. The shallow depth displacement calculations are consistent with previous work in the area. The State Line fault is believed to be a result of strain partitioning from the San Andreas Fault. By studying this more localized active strike-slip fault system the results of this study can contribute to a model that provides a better understanding of the tectonics in the central Basin and Range.

Fault and anthropogenic processes in central California constrained by satellite and airborne InSAR and in-situ observations

NASA Astrophysics Data System (ADS)

Liu, Zhen; Lundgren, Paul

2016-07-01

The San Andreas Fault (SAF) system is the primary plate boundary in California, with the central SAF (CSAF) lying adjacent to the San Joaquin Valley (SJV), a vast structural trough that accounts for about one-sixth of the United Sates' irrigated land and one-fifth of its extracted groundwater. The CSAF displays a range of fault slip behavior with creeping in its central segment that decreases towards its northwest and southeast ends, where the fault transitions to being fully locked. At least six Mw ~6.0 events since 1857 have occurred near the Parkfield transition, most recently in 2004. Large earthquakes also occurred on secondary faults parallel to the SAF, the result of distributed deformation across the plate boundary zone. Recent studies have revealed the complex interaction between anthropogenic related groundwater depletion and the seismic activity on adjacent faults through stress interaction. Despite recent progress, many questions regarding fault and anthropogenic processes in the region still remain. For example, how is the relative plate motion accommodated between the CSAF and off-fault deformation? What is the distribution of fault creep and slip deficit at shallow depths? What are the spatiotemporal variations of fault slip? What are the spatiotemporal characteristics of anthropogenic and lithospheric processes and how do they interact with each other? To address these, we combine satellite InSAR and NASA airborne UAVSAR data to image on and off-fault deformation. The UAVSAR data cover fault perpendicular swaths imaged from opposing look directions and fault parallel swaths since 2009. The much finer spatial resolution and optimized viewing geometry provide important constraints on near fault deformation and fault slip at very shallow depth. We performed a synoptic InSAR time series analysis using ERS-1/2, Envisat, ALOS and UAVSAR interferograms. The combined C-band ERS-1/2 and Envisat data provide a long time interval of SAR data over the region, but are subject to severe decorrelation. The L-band ALOS and UAVSAR SAR sensors provide improved coherence compared to the shorter wavelength radar data. Joint analysis of UAVSAR and ALOS interferometry measurements show clear variability in deformation along the fault strike, suggesting variable fault creep and locking at depth and along strike. Modeling selected fault transects reveals a distinct change in surface creep and shallow slip deficit from the central creeping section towards the Parkfield transition. In addition to fault creep, the L-band ALOS, and especially ALOS-2 ScanSAR interferometry, show large-scale ground subsidence in the SJV due to over-exploitation of groundwater. Groundwater related deformation is spatially and temporally variable and is composed of both recoverable elastic and non-recoverable inelastic components. InSAR time series are compared to GPS and well-water hydraulic head in-situ time series to understand water storage processes and mass loading changes. We are currently developing poroelastic finite element method models to assess the influence of anthropogenic processes on surface deformation and fault mechanics. Ongoing work is to better constrain both tectonic and non-tectonic processes and understand their interaction and implication for regional earthquake hazard.

MX Siting Investigation. Geotechnical Evaluation. Verification Study - Pahroc Valley, Nevada. Volume I. Synthesis.

DTIC Science & Technology

1981-06-30

Range both consist of Paleozoic limestone and dolomite overlain by Tertiary ash-flow tuffs and undiffer- entiated volcanic rocks. The central portion...andesite, detrital material, volcanic tuff, pumice). FAULT - A plane or zone of fracture along which there has been * I displacement. FAULT BLOCK...D2850-70). To conduct the test, a cylindrical specimen of soil is surrounded by a fluid in a pressure chamber and subjected to an isotropic pressure . An

Modification of wave-cut and faulting-controlled landforms.

USGS Publications Warehouse

Hanks, T.C.; Bucknam, R.C.; Lajoie, K.R.; Wallace, R.E.

1984-01-01

From a casual observation that the form of degraded fault scarps resembles the error function, this investigation proceeds through an elementary diffusion equation representation of landform evolution to the application of the resulting equations to the modern topography of scarplike landforms. The value of K = 1 GKG (K = 'mass diffusivity'; 1 GKG = 1m2/ka) may be generally applicable as a good first approximation, to the modification of alluvial terranes within the semiarid regions of the western United States. The Lake Bonneville shoreline K is the basis for dating four sets of fault scarps in west-central Utah. The Drum Mountains fault scarps date at 3.6 to 5.7 ka BP. Fault scarps along the eastern base of the Fish Springs Range are very young, 3 ka BP. We estimate the age of fault scarps along the western flank of the Oquirrh Mountains to be 32 ka B.P. Fault scarps along the NE margin of the Sheeprock Mountains are even older, 53 ka BP. -from Authors

Neotectonics and paleoseismology of the Limón and pedro miguel faults in Panamá: earthquake hazard to the Panamá canal

USGS Publications Warehouse

Rockwell, Thomas; Gath, Edon; Gonzalez, Tania; Madden, Chris; Verdugo, Danielle; Lippincott, Caitlin; Dawson, Tim; Owen, Lewis A.; Fuchs, Markus; Cadena, Ana; Williams, Pat; Weldon, Elise; Franceschi, Pastora

2010-01-01

We present new geologic, tectonic geomorphic, and geochronologic data on the slip rate, timing, and size of past surface ruptures for the right-lateral Lim??n and Pedro Miguel faults in central Panam??. These faults are part of a system of conjugate faults that accommodate the internal deformation of Panam?? resulting from the ongoing collision of Central and South America. There have been at least three surface ruptures on the Lim??n fault in the past 950-1400 years, with the most recent during the past 365 years. Displacement in this young event is at least 1.2 m (based on trenching) and may be 1.6-2 m (based on small channel offsets). Awell-preserved 4.2 m offset suggests that the penultimate event also sustained significant displacement. The Holocene slip rate has averaged about 6 mm=yr, based on a 30-m offset terrace riser incised into a 5-ka abandoned channel. The Pedro Miguel fault has sustained three surface ruptures in the past 1600 years, the most recent being the 2 May 1621 earthquake that partially destroyed Panam?? Viejo. At least 2.1 m of slip occurred in this event near the Canal, with geomorphic offsets suggesting 2.5-3 m. The historic Camino de Cruces is offset 2.8 m, indicating multimeter displacement over at least 20 km of fault length. Channel offsets of 100-400 m, together with a climate-induced incision model, suggest a Late Quaternary slip rate of about 5 mm=yr, which is consistent with the paleoseismic results. Comparison of the timing of surface ruptures between the Lim??n and Pedro Miguel faults suggests that large earthquakes may rupture both faults with 2-3 m of displacement for over 40 km, such as is likely in earthquakes in the M 7 range. Altogether, our observations indicate that the Lim??n and Pedro Miguel faults represent a significant seismic hazard to central Panam?? and, specifically, to the Canal and Panam?? City.

Unusually low rates of slip on the Santa Rosa Range fault zone, northern Nevada

USGS Publications Warehouse

Personius, S.F.; Mahan, S.A.

2005-01-01

The Santa Rosa Range fault zone (SRRFZ) is one of the most topographically prominent normal fault systems in the northern Basin and Range province of the western United States. It has been assigned high rates of vertical slip by others and has been identified as a possible site of the future extension of the central Nevada seismic belt (CNSB). We use detailed trench mapping and luminescence dating to estimate displacements and timing of the last several large-magnitude paleoearthquakes on the southern part of the SRRFZ at a trench site near Orovada, Nevada. Coseismic vertical displacements ranged from 1 to 2.8 m for each of the last four events. Luminescence ages provide time limits for the last three events of 125-155 ka, 90-108 ka, and 11-16 ka. These data yield recurrence intervals of 17-65 k.y. and 74-97 k.y. and an elapsed time of 11-16 k.y. since the youngest event. Slip-rate determinations at the Orovada site are complicated by multiple fault strands, but rates calculated from a variety of data are surprisingly low (0.01-0.16 mm/yr), given the topographic prominence of the Santa Rosa Range. A lack of compelling patterns in a comparison of paleoseismic parameters indicate that the SRRFZ is no more likely a location for a large-magnitude earthquake than previously identified seismic gaps or along faults that lie directly north of the CNSB.

Holocene activity and seismogenic capability of intraplate thrusts: Insights from the Pampean Ranges, Argentina

NASA Astrophysics Data System (ADS)

Costa, Carlos H.; Owen, Lewis A.; Ricci, Walter R.; Johnson, William J.; Halperin, Alan D.

2018-07-01

Trench excavations across the El Molino fault in the southeastern Pampean Ranges of central-western Argentina have revealed a deformation zone composed of opposite-verging thrusts that deform a succession of Holocene sediments. The west-verging thrusts place Precambrian basement over Holocene proximal scarp-derived deposits, whereas the east-verging thrusts form an east-directed fault-propagation fold that deforms colluvium, fluvial and aeolian deposits. Ages for exposed fault-related deposits range from 7.1 ± 0.4 to 0.3 ka. Evidence of surface deformation suggests multiple rupture events with related scarp-derived deposits and a minimum of three surface ruptures younger than 7.1 ± 0.4 ka, the last rupture event being younger than 1 ka. Shortening rates of 0.7 ± 0.2 mm/a are near one order of magnitude higher than those estimated for the faults bounding neighboring crustal blocks and are considered high for this intraplate setting. These ground-rupturing crustal earthquakes are estimated to be of magnitude Mw ≥ 7.0, a significant discrepancy with the magnitudes Mw < 6.5 recorded in the seismic catalog of this region at present with low to moderate seismicity. Results highlight the relevance of identifying primary surface ruptures as well as the seismogenic potential of thrust faults in seemingly stable continental interiors.

Reconnaissance study of late quaternary faulting along cerro GoDen fault zone, western Puerto Rico

USGS Publications Warehouse

Mann, P.; Prentice, C.S.; Hippolyte, J.-C.; Grindlay, N.R.; Abrams, L.J.; Lao-Davila, D.

2005-01-01

The Cerro GoDen fault zone is associated with a curvilinear, continuous, and prominent topographic lineament in western Puerto Rico. The fault varies in strike from northwest to west. In its westernmost section, the fault is ???500 m south of an abrupt, curvilinear mountain front separating the 270- to 361-m-high La CaDena De San Francisco range from the Rio A??asco alluvial valley. The Quaternary fault of the A??asco Valley is in alignment with the bedrock fault mapped by D. McIntyre (1971) in the Central La Plata quadrangle sheet east of A??asco Valley. Previous workers have postulated that the Cerro GoDen fault zone continues southeast from the A??asco Valley and merges with the Great Southern Puerto Rico fault zone of south-central Puerto Rico. West of the A??asco Valley, the fault continues offshore into the Mona Passage (Caribbean Sea) where it is characterized by offsets of seafloor sediments estimated to be of late Quaternary age. Using both 1:18,500 scale air photographs taken in 1936 and 1:40,000 scale photographs taken by the U.S. Department of Agriculture in 1986, we iDentified geomorphic features suggestive of Quaternary fault movement in the A??asco Valley, including aligned and Deflected drainages, apparently offset terrace risers, and mountain-facing scarps. Many of these features suggest right-lateral displacement. Mapping of Paleogene bedrock units in the uplifted La CaDena range adjacent to the Cerro GoDen fault zone reveals the main tectonic events that have culminated in late Quaternary normal-oblique displacement across the Cerro GoDen fault. Cretaceous to Eocene rocks of the La CaDena range exhibit large folds with wavelengths of several kms. The orientation of folds and analysis of fault striations within the folds indicate that the folds formed by northeast-southwest shorTening in present-day geographic coordinates. The age of Deformation is well constrained as late Eocene-early Oligocene by an angular unconformity separating folDed, Deep-marine middle Eocene rocks from transgressive, shallow-marine rocks of middle-upper Oligocene age. Rocks of middle Oligocene-early Pliocene age above unconformity are gently folDed about the roughly east-west-trending Puerto Rico-Virgin Islands arch, which is well expressed in the geomorphology of western Puerto Rico. Arching appears ongoing because onshore and offshore late Quaternary oblique-slip faults closely parallel the complexly Deformed crest of the arch and appear to be related to exTensional strains focused in the crest of the arch. We estimate ???4 km of vertical throw on the Cerro GoDen fault based on the position of the carbonate cap north of the fault in the La CaDena De San Francisco and its position south of the fault inferred from seismic reflection data in Mayaguez Bay. Based on these observations, our interpretation of the kinematics and history of the Cerro GoDen fault zone incluDes two major phases of motion: (1) Eocene northeast-southwest shorTening possibly accompanied by left-lateral shearing as Determined by previous workers on the Great Southern Puerto Rico fault zone; and (2) post-early Pliocene regional arching of Puerto Rico accompanied by normal offset and right-lateral shear along faults flanking the crest of the arch. The second phase of Deformation accompanied east-west opening of the Mona rift and is inferred to continue to the present day. ?? 2005 Geological Society of America.

The enigma of the Arthur's Pass, New Zealand, earthquake 1. Reconciling a variety of data for an unusual earthquake sequence

USGS Publications Warehouse

Abercrombie, R.E.; Webb, T.H.; Robinson, R.; McGinty, P.J.; Mori, J.J.; Beavan, R.J.

2000-01-01

The 1994 Arthur's Pass earthquake (Mw6.7) is the largest in a recent sequence of earthquakes in the central South Island, New Zealand. No surface rupture was observed the aftershock distribution was complex, and routine methods of obtaining the faulting orientation of this earthquake proved contradictory. We use a range of data and techniques to obtain our preferred solution, which has a centroid depth of 5 km, Mo=1.3??1019 N m, and a strike, dip, and rake of 221??, 47??, 112??, respectively. Discrepancies between this solution and the Harvard centroid moment tensor, together with the Global Positioning System (GPS) observations and unusual aftershock distribution, suggest that the rupture may not have occurred on a planar fault. A second, strike slip, subevent on a more northerly striking plane is suggested by these data but neither the body wave modeling nor regional broadband recordings show any complexity or late subevents. We relocate the aftershocks using both one-dimensional and three-dimensional velocity inversions. The depth range of the aftershocks (1-10 km) agrees well with the preferred mainshock centroid depth. The aftershocks near the hypocenter suggest a structure dipping toward the NW, which we interpret to be the mainshock fault plane. This structure and the Harper fault, ???15 km to the south appear to have acted as boundaries to the extensive aftershock zone trending NNW-SSE Most of the ML???5 aftershocks, including the two largest (ML6.1 and ML5.7), clustered near the Harper fault and have strike slip mechanisms consistent with motion on this fault and its conjugates. Forward modeling of the GPS data suggests that a reverse slip mainshock, combined with strike slip aftershock faulting in the south, is able to match the observed displacements. The occurrence of this earthquake sequence implies that the level of seismic hazard in the central South Island is greater than previous estimates. Copyright 2000 by the American Geophysical Union.

Shallow crustal structure of eastern-central Trans-Mexican Volcanic Belt.

NASA Astrophysics Data System (ADS)

Campos-Enriquez, J. O.; Ramón, V. M.; Lermo-Samaniego, J.

2015-12-01

Central-eastern Trans-Mexican Volcanic Belt (TMVB) is featured by large basins (i.e., Toluca, Mexico, Puebla-Tlaxcala, Libres-Oriental). It has been supposed that major crustal faults limit these basins. Sierra de Las Cruces range separates the Toluca and Mexico basins. The Sierra Nevada range separates Mexico basin from the Puebla-Tlaxcala basin. Based in gravity and seismic data we inferred the Toluca basin is constituted by the Ixtlahuaca sub-basin, to the north, and the Toluca sub-basin to the south, which are separated by a relative structural high. The Toluca depression is more symmetric and bounded by sub-vertical faults. In particular its eastern master fault controlled the emplacement of Sierra de Las Cruces range. Easternmost Acambay graben constitutes the northern and deepest part of the Ixtlahuaca depression. The Toluca-Ixtlahuaca basin is inside the Taxco-San Miguel de Allende fault system, and limited to the west by the Guerrero terrane which continues beneath the TMVB up to the Acambay graben. Mexico basin basement occupies an intermediate position and featured by a relative structural high to the north-east, as established by previous studies. This relative structural high is limited to the west by the north-south Mixhuca trough, while to the south it is bounded by the east-west Copilco-Xochimilco-Chalco sub-basin. The Puebla-Tlaxcala basin basement is the shallowest of these 3 tectonic depressions. In general, features (i.e., depth) and relationship between these basins, from west to east, are controlled by the regional behavior of the Sierra Madre Oriental fold and thrust belt basement (i.e., Oaxaca Complex?). This study indicates that an active east-west regional fault system limits to the south the TMVB (from the Nevado de Toluca volcano through the Popocatepetl volcano and eastward along southern Puebla-Tlaxcala basin). The Tenango and La Pera fault systems constituting the western part of this regional fault system coincide with northern exposures of the Morelos platform to the west. The eastward extension of this system limits the northern Acatlan Complex exposures. Accordingly, eastern TMVB has been subjected to extension and associated faults are being activated at present. The basins act as independent crustal blocks. The Puebla-Tlaxcala and the Tehuacan basins merge to the east.

Deep crustal electromagnetic structure of central India tectonic zone and its implications

NASA Astrophysics Data System (ADS)

Naganjaneyulu, K.; Naidu, G. Dhanunjaya; Rao, M. Someswara; Shankar, K. Ravi; Kishore, S. R. K.; Murthy, D. N.; Veeraswamy, K.; Harinarayana, T.

2010-07-01

Magnetotelluric data at 45 locations along the Mahan-Khajuria Kalan profile in the central India tectonic zone are analysed. This 290 km long profile yields data in the period range 0.001-1000 s across the tectonic elements of the study region bounded by Purna fault, Gavligarh fault, Tapti fault, Narmada South fault and Narmada North fault. Multi-site, multi-frequency analysis suggests N70°E as the geo-electric strike direction. Data rotated into the N70°E strike direction are modelled using a non-linear conjugate gradient scheme with error floors of 10% for both apparent resistivity and phase components. Two-dimensional magnetotelluric model yields conductors that correlate with known faults in the study region and regional seismicity. Presence of a -30 mgal gravity high together with the observed conductive bodies (less than 20 ohm m) in the deep crust beneath the Purna graben and Tapti valley is explained by the process of magmatic underplating. The conductive bodies beneath the Mahakoshal rift belt and Vindhyans accompanied by regional gravity lows of the order -70 mgal are attributed to the presence of deep crustal fluids. Following the re-activation model proposed for the entire region, the conductors (20 ohm m) at various depth levels correspond to mafic magmatic and/or fluid intrusions controlled by deep-seated faults that seem to tap reservoirs beyond the crust-mantle boundary. The shallow depth localized faults also seem to have facilitated further upward movement of these underplated material and fluids release during this process.

Using surface creep rate to infer fraction locked for sections of the San Andreas fault system in northern California from alignment array and GPS data

USGS Publications Warehouse

Lienkaemper, James J.; McFarland, Forrest S.; Simpson, Robert W.; Caskey, S. John

2014-01-01

Surface creep rate, observed along five branches of the dextral San Andreas fault system in northern California, varies considerably from one section to the next, indicating that so too may the depth at which the faults are locked. We model locking on 29 fault sections using each section’s mean long‐term creep rate and the consensus values of fault width and geologic slip rate. Surface creep rate observations from 111 short‐range alignment and trilateration arrays and 48 near‐fault, Global Positioning System station pairs are used to estimate depth of creep, assuming an elastic half‐space model and adjusting depth of creep iteratively by trial and error to match the creep observations along fault sections. Fault sections are delineated either by geometric discontinuities between them or by distinctly different creeping behaviors. We remove transient rate changes associated with five large (M≥5.5) regional earthquakes. Estimates of fraction locked, the ratio of moment accumulation rate to loading rate, on each section of the fault system provide a uniform means to inform source parameters relevant to seismic‐hazard assessment. From its mean creep rates, we infer the main branch (the San Andreas fault) ranges from only 20%±10% locked on its central creeping section to 99%–100% on the north coast. From mean accumulation rates, we infer that four urban faults appear to have accumulated enough seismic moment to produce major earthquakes: the northern Calaveras (M 6.8), Hayward (M 6.8), Rodgers Creek (M 7.1), and Green Valley (M 7.1). The latter three faults are nearing or past their mean recurrence interval.

Mantle to Surface Dynamics Across Subduction-Collision Transitions in Space and Time: Results from the CD-CAT Project in Anatolia

NASA Astrophysics Data System (ADS)

Whitney, D. L.; Abgarmi, B.; Beck, S. L.; Brocard, G. Y.; Cosca, M. A.; Darin, M. H.; Delph, J. R.; Hui, H.; Kahraman, M.; Kaymakci, N.; Kuscu, G.; Meijers, M. J.; Mulch, A.; Özacar, A.; Portner, D. E.; Reid, M. R.; Rey, P. F.; Rojay, B.; Schlieffarth, W. K.; Sandvol, E. A.; Schoenbohm, L. M.; Tank, B.; Teoman, U.; Teyssier, C. P.; Thomson, S. N.; Turkelli, N.; Umhoefer, P. J.; Uslular, G.; Willenbring, J. K.

2017-12-01

From west to east, the southern plate boundary of Anatolia varies from subduction to continental collision; plate dynamics are influenced by the interaction of back-arc extension in the west (Aegean) and convergence in the east (Arabia-Eurasia). Prior to 40 Ma, the entire margin was a subduction zone. The NSF project "Continental Dynamics-Central Anatolian Tectonics (CD-CAT)" has contributed to understanding how the mantle, crust, and surface evolve in subduction-to-collision transitions in time and space. Differences are seen in changes in deformation style as collision proceeded; e.g. from distributed across a broad zone to highly localized on a series of oblique-slip faults, and from transpression to transtension (W of the Central Anatolian fault zone, CAFZ) or strike-slip (E of the CAFZ); age, composition, and sources of magmatism, including a magmatic lull from 40-20 Ma, followed by expansion of magmatism SE-ward in central Anatolia; properties and architecture of the lithosphere and sub-lithospheric mantle (e.g. significant and locally abrupt crustal thickness variations, including thick crust under the Tauride Mts; thin to absent lithospheric mantle; and a torn and disaggregating slab that varies from shallow to steep below central Anatolia); and a topographic gradient from a high eastern plateau (> 2 km) to a central plateau (1-1.5 km) bounded to the N and S by mountain ranges that rose > 2 km from the sea between 11-5 Ma, producing a rain shadow in the Anatolian interior. Thermochronologic and structural studies of exhumed mid-crust and associated basins and fault zones as well as geophysical data for Anatolia today show the extent to which inherited features (suture zones, faults) have affected the tectonic evolution of Anatolia, particularly in the vicinity of the CAFZ/East Anatolian Fault, and mantle properties. Results also show that the Miocene was a dynamic time in the thermal and mechanical evolution of the region, as early Miocene rollback/foundering of the subducted slab drove major volcanism, faulting, and landscape changes (uplift). Slab dynamics below Anatolia accelerated the late Miocene-Pliocene transition from distributed to highly localized deformation, including inception of the North and East Anatolia strike-slip faults that today accommodate tectonic escape of Anatolia.

The Seismicity of the Central Apennines Region Studied by Means of a Physics-Based Earthquake Simulator

NASA Astrophysics Data System (ADS)

Console, R.; Vannoli, P.; Carluccio, R.

2016-12-01

The application of a physics-based earthquake simulation algorithm to the central Apennines region, where the 24 August 2016 Amatrice earthquake occurred, allowed the compilation of a synthetic seismic catalog lasting 100 ky, and containing more than 500,000 M ≥ 4.0 events, without the limitations that real catalogs suffer in terms of completeness, homogeneity and time duration. The algorithm on which this simulator is based is constrained by several physical elements as: (a) an average slip rate for every single fault in the investigated fault systems, (b) the process of rupture growth and termination, leading to a self-organized earthquake magnitude distribution, and (c) interaction between earthquake sources, including small magnitude events. Events nucleated in one fault are allowed to expand into neighboring faults, even belonging to a different fault system, if they are separated by less than a given maximum distance. The seismogenic model upon which we applied the simulator code, was derived from the DISS 3.2.0 database (http://diss.rm.ingv.it/diss/), selecting all the fault systems that are recognized in the central Apennines region, for a total of 24 fault systems. The application of our simulation algorithm provides typical features in time, space and magnitude behavior of the seismicity, which are comparable with those of real observations. These features include long-term periodicity and clustering of strong earthquakes, and a realistic earthquake magnitude distribution departing from the linear Gutenberg-Richter distribution in the moderate and higher magnitude range. The statistical distribution of earthquakes with M ≥ 6.0 on single faults exhibits a fairly clear pseudo-periodic behavior, with a coefficient of variation Cv of the order of 0.3-0.6. We found in our synthetic catalog a clear trend of long-term acceleration of seismic activity preceding M ≥ 6.0 earthquakes and quiescence following those earthquakes. Lastly, as an example of a possible use of synthetic catalogs, an attenuation law was applied to all the events reported in the synthetic catalog for the production of maps showing the exceedence probability of given values of peak acceleration (PGA) on the territory under investigation. The application of a physics-based earthquake simulation algorithm to the central Apennines region, where the 24 August 2016 Amatrice earthquake occurred, allowed the compilation of a synthetic seismic catalog lasting 100 ky, and containing more than 500,000 M ≥ 4.0 events, without the limitations that real catalogs suffer in terms of completeness, homogeneity and time duration. The algorithm on which this simulator is based is constrained by several physical elements as: (a) an average slip rate for every single fault in the investigated fault systems, (b) the process of rupture growth and termination, leading to a self-organized earthquake magnitude distribution, and (c) interaction between earthquake sources, including small magnitude events. Events nucleated in one fault are allowed to expand into neighboring faults, even belonging to a different fault system, if they are separated by less than a given maximum distance. The seismogenic model upon which we applied the simulator code, was derived from the DISS 3.2.0 database (http://diss.rm.ingv.it/diss/), selecting all the fault systems that are recognized in the central Apennines region, for a total of 24 fault systems. The application of our simulation algorithm provides typical features in time, space and magnitude behavior of the seismicity, which are comparable with those of real observations. These features include long-term periodicity and clustering of strong earthquakes, and a realistic earthquake magnitude distribution departing from the linear Gutenberg-Richter distribution in the moderate and higher magnitude range. The statistical distribution of earthquakes with M ≥ 6.0 on single faults exhibits a fairly clear pseudo-periodic behavior, with a coefficient of variation Cv of the order of 0.3-0.6. We found in our synthetic catalog a clear trend of long-term acceleration of seismic activity preceding M ≥ 6.0 earthquakes and quiescence following those earthquakes. Lastly, as an example of a possible use of synthetic catalogs, an attenuation law was applied to all the events reported in the synthetic catalog for the production of maps showing the exceedence probability of given values of peak acceleration (PGA) on the territory under investigation.

Preliminary paleoseismic observations along the western Denali fault, Alaska

NASA Astrophysics Data System (ADS)

Koehler, R. D.; Schwartz, D. P.; Rood, D. H.; Reger, R.; Wolken, G. J.

2013-12-01

The Denali fault in south-central Alaska, from Mt. McKinley to the Denali-Totschunda fault branch point, accommodates ~9-12 mm/yr of the right-lateral component of oblique convergence between the Pacific/Yakutat and North American plates. The eastern 226 km of this fault reach was part of the source of the 2002 M7.9 Denali fault earthquake. West of the 2002 rupture there is evidence of two large earthquakes on the Denali fault during the past ~550-700 years but the paleoearthquake chronology prior to this time is largely unknown. To better constrain fault rupture parameters for the western Denali fault and contribute to improved seismic hazard assessment, we performed helicopter and ground reconnaissance along the southern flank of the Alaska Range between the Nenana Glacier and Pyramid Peak, a distance of ~35 km, and conducted a site-specific paleoseismic study. We present a Quaternary geologic strip map along the western Denali fault and our preliminary paleoseismic results, which include a differential-GPS survey of a displaced debris flow fan, cosmogenic 10Be surface exposure ages for boulders on this fan, and an interpretation of a trench across the main trace of the fault at the same site. Between the Nenana Glacier and Pyramid Peak, the Denali fault is characterized by prominent tectonic geomorphic features that include linear side-hill troughs, mole tracks, anastamosing composite scarps, and open left-stepping fissures. Measurements of offset rills and gullies indicate that slip during the most recent earthquake was between ~3 and 5 meters, similar to the average displacement in the 2002 earthquake. At our trench site, ~ 25 km east of the Parks Highway, a steep debris fan is displaced along a series of well-defined left-stepping linear fault traces. Multi-event displacements of debris-flow and snow-avalanche channels incised into the fan range from 8 to 43 m, the latter of which serves as a minimum cumulative fan offset estimate. The trench, excavated into the fan across the main fault scarp and adjacent graben, exposed sheared debris fan parent material at its north and south ends, separated by a central zone of stacked scarp-derived colluvium and weakly developed peaty soils. Stratigraphic relations and upward fault terminations clearly record the occurrence of the past three surface-faulting earthquakes and suggest four or more such events. Results of pending 14C analyses are expected to provide new information on earthquake timing and recurrence. A Holocene slip rate for this section of the fault will be developed using back-slip models and an estimate of the age of the fan constrained by our detailed surveys of channel offsets and pending cosmogenic 10Be exposure ages for surface boulders, respectively.

Paleoseismological surveys on the Hinagu fault zone in Kumamoto, central Kyushu, Japan

NASA Astrophysics Data System (ADS)

Azuma, T.

2017-12-01

The Hinagu fault zone is located on the south of the Futagawa fault zone, which was a main part of the source fault of the 2016 Kumamoto earthquake of Mj 7.3. Northernmost part of the Hinagu fault zone was also acted in 2016 event and surface faults with right-lateral displacement upto ca. 50 cm were appeared. Seismicity along the central part of the Hinagu fault was increased just after the 2016 Kumamoto Earthquake. It seems that the Hinagu fault zone would produce the next large earthquake in the near future, although it has not occurred yet. The Headquarters of the Earthquake Research Promotions (HERP) conducted active fault surveys on the Hinagu fault zone to recognize the probability of the occurrence of the next faulting event. The Hinagu fault zone is composed with 3 fault segments, Takano-Shirahata, Hinagu, and Yatsushiro Bay. Yatsushiro Bay segment is offshore fault. In FY2016, we conducted paleoseismological trenching surveys at 2 sites (Yamaide, Minamibeta) and offshore drilling. Those result showed evidences that the recurrence intervals of the Hinagu fault zone was rather short and the last faulting event occurred around 1500-2000 yrsBP. In FY2017, we are planning another trenching survey on the southern part of the central segment, where Yatsushiro city located close to the fault.

A study of Quaternary structures in the Qom region, West Central Iran

NASA Astrophysics Data System (ADS)

Babaahmadi, A.; Safaei, H.; Yassaghi, A.; Vafa, H.; Naeimi, A.; Madanipour, S.; Ahmadi, M.

2010-12-01

West Central Iran comprises numerous Quaternary faults. Having either strike-slip or thrust mechanisms, these faults are potentially active and therefore capable of creating destructive earthquakes. In this paper, we use satellite images as well as field trips to identify these active faults in the Qom region. The Qom and Indes faults are the main NW-trending faults along which a Quaternary restraining step-over zone has formed. Kamarkuh, Mohsen Abad, and Ferdows anticlines are potentially active structures that formed in this restraining step-over zone. There are some thrusts and anticlines, such as the Alborz anticline and Alborz fault, which are parallel to strike-slip faults such as the Qom fault, indicating deformation partitioning in the area. In addition to NW-trending structures, there is an important NE-trending fault known as the Qomrud fault that has deformed Quaternary deposits and affected Kushk-e-Nosrat fault, Alborz anticline, and Qomrud River. The results of this study imply that the major Quaternary faults of West Central Iran and their restraining step-over zones are potentially active.

Elevation changes in the central transverse ranges near Ventura, California

USGS Publications Warehouse

Buchanan-Banks, J. M.; Castle, R.O.; Ziony, J.I.

1975-01-01

Profiles of elevation changes developed from repeated levelings in the east-trending Transverse Ranges near Ventura, California, reveal three general types of vertical movements: 1. (1) broadly defined regional tilting; 2. (2) sharply defined differential movements across recently active faults; and 3. (3) differential subsidence centering on producing oil fields. Down-to-the-southeast tilting is evident in profiles along the coast this sense of movement, however, is the inverse of that that may have prevailed during late Pleistocene time. Profiles along lines extending north and northwest from Ventura show prominent inflections formed by up-to-the-north differential movements that coincide roughly with the Red Mountain fault; this fault is a north-dipping reverse fault that displaces a Holocene(?) soil zone and along which scarps and sag ponds are preserved. A similar inflection coincides with the Padre Juan fault; post-Pleistocene activity on the Padre Juan, however, is uniquely indicated by the geodetic data. Contemporary integrity of the structural block extending northward from the Red Mountain fault is suggested by the apparent absence of differential movements across the Munson Creek, Tule Creek, Santa Ynez, and Arroyo Parida faults since at least 1934. Subsidence is recognized over both the Ventura and Rincon oil fields; although maximum subsidence has not been recorded in either case, 277 mm of differential subsidence was measured within the Ventura field between 1934 and 1968. ?? 1975.

Active fault characterization throughout the Caribbean and Central America for seismic hazard modeling

NASA Astrophysics Data System (ADS)

Styron, Richard; Pagani, Marco; Garcia, Julio

2017-04-01

The region encompassing Central America and the Caribbean is tectonically complex, defined by the Caribbean plate's interactions with the North American, South American and Cocos plates. Though active deformation over much of the region has received at least cursory investigation the past 50 years, the area is chronically understudied and lacks a modern, synoptic characterization. Regardless, the level of risk in the region - as dramatically demonstrated by the 2010 Haiti earthquake - remains high because of high-vulnerability buildings and dense urban areas home to over 100 million people, who are concentrated near plate boundaries and other major structures. As part of a broader program to study seismic hazard worldwide, the Global Earthquake Model Foundation is currently working to quantify seismic hazard in the region. To this end, we are compiling a database of active faults throughout the region that will be integrated into similar models as recently done in South America. Our initial compilation hosts about 180 fault traces in the region. The faults show a wide range of characteristics, reflecting the diverse styles of plate boundary and plate-margin deformation observed. Regional deformation ranges from highly localized faulting along well-defined strike-slip faults to broad zones of distributed normal or thrust faulting, and from readily-observable yet slowly-slipping structures to inferred faults with geodetically-measured slip rates >10 mm/yr but essentially no geomorphic expression. Furthermore, primary structures such as the Motagua-Polochic Fault Zone (the strike-slip plate boundary between the North American and Caribbean plates in Guatemala) display strong along-strike slip rate gradients, and many other structures are undersea for most or all of their length. A thorough assessment of seismic hazard in the region will require the integration of a range of datasets and techniques and a comprehensive characterization of epistemic uncertainties driving the overall variability of hazard and risk results. For this reason and in order to leverage from the knowledge available in the region, datasets and the hazard model will be developed in close collaboration with local experts coherently with GEM's principles of transparency and collaboration. For what pertains active faults in shallow crust, we are currently working on assigning slip rates to structures based on geologic and geodetic strain rates, though this will be challenging in areas of sparse constraints. An additional area of ongoing work is the delineation of 3D seismic sources from disjoint fault traces; we are currently evaluating methods for this. Though work in the region is challenging, we anticipate that our results will not only lead to more robust seismic hazard and risk estimates for the region, but may serve as a template for workflows in other zones of poor or inhomogeneous data.

Deformation across the Pacific-North America plate boundary near San Francisco, California

USGS Publications Warehouse

Prescott, W.H.; Savage, J.C.; Svarc, J.L.; Manaker, D.

2001-01-01

We have detected a narrow zone of compression between the Coast Ranges and the Great Valley, and we have estimated slip rates for the San Andreas, Rodgers Creek, and Green Valley faults just north of San Francisco. These results are based on an analysis of campaign and continuous Global Positioning System (GPS) data collected between 1992 and 2000 in central California. The zone of compression between the Coast Ranges and the Great Valley is 25 km wide. The observations clearly show 3.8??1.5 mm yr-1 of shortening over this narrow zone. The strike slip components are best fit by a model with 20.8??1.9 mm yr-1 slip on the San Andreas fault, 10.3??2.6 mm yr-1 on the Rodgers Creek fault, and 8.1??2.1 mm yr-1 on the Green Valley fault. The Pacific-Sierra Nevada-Great Valley motion totals 39.2??3.8 mm yr-1 across a zone that is 120 km wide (at the latitude of San Francisco). Standard deviations are one ??. The geodetic results suggest a higher than geologic rate for the Green Valley fault. The geodetic results also suggest an inconsistency between geologic estimates of the San Andreas rate and seismologic estimates of the depth of locking on the San Andreas fault. The only convergence observed is in the narrow zone along the border between the Great Valley and the Coast Ranges.

Soda Creek springs - metamorphic waters in the eastern Alaska Range

USGS Publications Warehouse

Richter, D.H.; Donaldson, D.E.; Lamarre, R.A.

1973-01-01

The Soda Creek springs are a group of small, cold mineral springs on the southern flank of the eastern Alaska Range. The spring waters contain anomalous concentrations of carbon dioxide, sodium, chlorine, sulfate, boron, and ammonia and are actively precipitating deposits of calcite and aragonite. Sparingly present in these deposits are mixed-layer illite-montmorillonite clays and zeolite minerals. Low-temperaturemetamorphic reactions in subjacent marine sedimentary rocks of Jurassic and Cretaceous age may have produced the fluids and silicate minerals. With only a few exceptions, cool bicarbonate-rich springs in Alaska are concentrated south of the Denali fault system in south-central Alaska, southeastern Alaska, and along the Kaltag-Tintina fault system. These areas are characterized by active or recently activetectonism, major faults and folds, and an abundance of marine sedimentary rocks.

Along strike behavior of the Tizi n' Firest fault during the Lower Jurassic rifting (Central High Atlas Carbonate basin, Morocco)

NASA Astrophysics Data System (ADS)

Sarih, S.; Quiquerez, A.; Allemand, P.; Garcia, J. P.; El Hariri, K.

2018-03-01

The purpose of this study is to document the along-strike early syn-rift history of the Lower Jurassic Carbonate basin of the Central High Atlas (Morocco) by combining sedimentological observations and high-resolution biostratigraphy. Six sections, each from the Sinemurian to the Upper Pliensbachian, were investigated along a 75 km-long transect at the hanging wall of a major fault of the Lower Jurassic Basin (i.e. the Tizi n' Firest fault). Depositional geometries of the early syn-rift deposits were reconstructed from the correlation between eight main timelines dated by biochronological markers for a time span covering about 6 Ma. Depocentre migration was examined and accommodation rates were calculated at the sub-zone timescale to discuss the along-strike-fault behavior of the Lower Jurassic basin formation. The early stages of extension are marked by contrasted along-strike variations in depositional geometry thickness, depocentre migration and accommodation rates, leading to the growth of three independent sub-basins (i.e. western, central, and eastern), ranging in size from 30 to 50 km, and displaying three contrasted tectono-sedimentary histories. Our results suggest that, during the early rifting phase, tectonic activity was not a continuous and progressive process evolving towards a rift climax stage, but rather a series of acceleration periods that alternated with periods of much reduced activity. The length of active fault segments is estimated at about 15-20 km, with a lifespan of a few ammonite sub-zones (> 2-3 Ma).

Cenozoic pull-apart basins in southwest Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruppel, E.T.

1991-06-01

Faults and fault zones bounding the mountain ranges of southwest Montana commonly have been described as normal faults, and the region has been considered to be a northern extension of the Basin and Range. New geologic mapping suggests, however, that Cenozoic movements along most of the zones of steep faults in southwest Montana and in east-central Idaho have been strike-slip, and the intermontane basins appear to be pull-aparts. The principal fault zones trend about north, northwest, east, and north-northeast; the north-trending zones are Cenozoic in age, but the others are of Archean ancestry and are rooted in basement rocks. Thesemore » faults break the region into rhomboidal mountain blocks separated by broad basins with parallel sides. The basins are as much as 5,000 m deep, and their floors are deeply indented by centers of subsidence wherre they are crossed by major fault zones. The basins are floored by Archean or Proterozoic rocks and are filled with tuffaceous sedimentary rocks of late Oligocene to late Miocene age. The Big Hole basin and the smaller basins in upper Grasshopper Creek and Horse Prairie are interpreted to be pull-aparts between zones of east-trending right-lateral faults. The cratonic basins farther east in southwest Montana are interpreted to be basement-floored openings between mountain blocks that have been separated by subcrustal flow to the northwest. The interpretations suggest that significant accumulations of oil or gas are not likely to be found in this region.« less

Growth and linkage of the quaternary Ubrique Normal Fault Zone, Western Gibraltar Arc: role on the along-strike relief segmentation

NASA Astrophysics Data System (ADS)

Jiménez-Bonilla, Alejandro; Balanya, Juan Carlos; Exposito, Inmaculada; Diaz-Azpiroz, Manuel; Barcos, Leticia

2015-04-01

Strain partitioning modes within migrating orogenic arcs may result in arc-parallel stretching that produces along-strike structural and topographic discontinuities. In the Western Gibraltar Arc, arc-parallel stretching has operated from the Lower Miocene up to recent times. In this study, we have reviewed the Colmenar Fault, located at the SW end of the Subbetic ranges, previously interpreted as a Middle Miocene low-angle normal fault. Our results allow to identify younger normal fault segments, to analyse their kinematics, growth and segment linkage, and to discuss its role on the structural and relief drop at regional scale. The Colmenar Fault is folded by post-Serravallian NE-SW buckle folds. Both the SW-dipping fault surfaces and the SW-plunging fold axes contribute to the structural relief drop toward the SW. Nevertheless, at the NW tip of the Colmenar Fault, we have identified unfolded normal faults cutting quaternary soils. They are grouped into a N110˚E striking brittle deformation band 15km long and until 3km wide (hereafter Ubrique Normal Fault Zone; UNFZ). The UNFZ is divided into three sectors: (a) The western tip zone is formed by normal faults which usually dip to the SW and whose slip directions vary between N205˚E and N225˚E. These segments are linked to each other by left-lateral oblique faults interpreted as transfer faults. (b) The central part of the UNFZ is composed of a single N115˚E striking fault segment 2,4km long. Slip directions are around N190˚E and the estimated throw is 1,25km. The fault scarp is well-conserved reaching up to 400m in its central part and diminishing to 200m at both segment terminations. This fault segment is linked to the western tip by an overlap zone characterized by tilted blocks limited by high-angle NNE-SSW and WNW-ESE striking faults interpreted as "box faults" [1]. (c) The eastern tip zone is formed by fault segments with oblique slip which also contribute to the downthrown of the SW block. This kinematic pattern seems to be related to other strike-slip fault systems developed to the E of the UNFZ. The structural revision together with updated kinematic data suggest that the Colmenar Fault is cut and downthrown by a younger normal fault zone, the UNFZ, which would have contributed to accommodate arc-parallel stretching until the Quaternary. This stretching provokes along-strike relief segmentation, being the UNFZ the main fault zone causing the final drop of the Subbetic ranges towards the SW within the Western Gibraltar Arc. Our results show displacement variations in each fault segment of the UNFZ, diminishing to their tips. This suggests fault segment linkage finally evolved to build the nearly continuous current fault zone. The development of current large through-going faults linked inside the UNFZ is similar to those ones simulated in some numerical modelling of rift systems [2]. Acknowledgements: RNM-415 and CGL-2013-46368-P [1]Peacock, D.C.P., Knipe, R.J., Sanderson, D.J., 2000. Glossary of normal faults. Journal Structural Geology, 22, 291-305. [2]Cowie, P.A., Gupta, S., Dawers, N.H., 2000. Implications of fault array evolution for synrift depocentre development: insights from a numerical fault growth model. Basin Research, 12, 241-261.

Database for the geologic map of the Bend 30- x 60-minute quadrangle, central Oregon

USGS Publications Warehouse

Koch, Richard D.; Ramsey, David W.; Sherrod, David R.; Taylor, Edward M.; Ferns, Mark L.; Scott, William E.; Conrey, Richard M.; Smith, Gary A.

2010-01-01

The Bend 30- x 60-minute quadrangle has been the locus of volcanism, faulting, and sedimentation for the past 35 million years. It encompasses parts of the Cascade Range and Blue Mountain geomorphic provinces, stretching from snowclad Quaternary stratovolcanoes on the west to bare rocky hills and sparsely forested juniper plains on the east. The Deschutes River and its large tributaries, the Metolius and Crooked Rivers, drain the area. Topographic relief ranges from 3,157 m (10,358 ft) at the top of South Sister to 590 m (1,940 ft) at the floor of the Deschutes and Crooked Rivers where they exit the area at the north-central edge of the map area. The map encompasses a part of rapidly growing Deschutes County. The city of Bend, which has over 70,000 people living in its urban growth boundary, lies at the south-central edge of the map. Redmond, Sisters, and a few smaller villages lie scattered along the major transportation routes of U.S. Highways 97 and 20. This geologic map depicts the geologic setting as a basis for structural and stratigraphic analysis of the Deschutes basin, a major hydrologic discharge area on the east flank of the Cascade Range. The map also provides a framework for studying potentially active faults of the Sisters fault zone, which trends northwest across the map area from Bend to beyond Sisters. This digital release contains all of the information used to produce the geologic map published as U.S. Geological Survey Geologic Investigations Series I-2683 (Sherrod and others, 2004). The main component of this digital release is a geologic map database prepared using ArcInfo GIS. This release also contains files to view or print the geologic map and accompanying descriptive pamphlet from I-2683.

New geomorphic data on the active Taiwan orogen: A multisource approach

NASA Technical Reports Server (NTRS)

Deffontaines, B.; Lee, J.-C.; Angelier, J.; Carvalho, J.; Rudant, J.-P.

1994-01-01

A multisource and multiscale approach of Taiwan morphotectonics combines different complementary geomorphic analyses based on a new elevation model (DEM), side-looking airborne radar (SLAR), and satellite (SPOT) imagery, aerial photographs, and control from independent field data. This analysis enables us not only to present an integrated geomorphic description of the Taiwan orogen but also to highlight some new geodynamic aspects. Well-known, major geological structures such as the Longitudinal Valley, Lishan, Pingtung, and the Foothills fault zones are of course clearly recognized, but numerous, previously unrecognized structures appear distributed within different regions of Taiwan. For instance, transfer fault zones within the Western Foothills and the Central Range are identified based on analyses of lineaments and general morphology. In many cases, the existence of geomorphic features identified in general images is supported by the results of geological field analyses carried out independently. In turn, the field analyses of structures and mechanisms at some sites provide a key for interpreting similar geomorphic featues in other areas. Examples are the conjugate pattern of strike-slip faults within the Central Range and the oblique fold-and-thrust pattern of the Coastal Range. Furthermore, neotectonic and morphological analyses (drainage and erosional surfaces) has been combined in order to obtain a more comprehensive description and interpretation of neotectonic features in Taiwan, such as for the Longitudinal Valley Fault. Next, at a more general scale, numerical processing of digital elevation models, resulting in average topography, summit level or base level maps, allows identification of major features related to the dynamics of uplift and erosion and estimates of erosion balance. Finally, a preliminary morphotectonic sketch map of Taiwan, combining information from all the sources listed above, is presented.

Moderate rates of late Quaternary slip along the northwestern margin of the Basin and Range Province, Surprise Valley fault, northeastern California

USGS Publications Warehouse

Personius, Stephen F.; Crone, Anthony J.; Machette, Michael N.; Mahan, Shannon; Lidke, David J.

2009-01-01

The 86-km-long Surprise Valley normal fault forms part of the active northwestern margin of the Basin and Range province in northeastern California. We use trench mapping and radiocarbon, luminescence, and tephra dating to estimate displacements and timing of the past five surface-rupturing earthquakes on the central part of the fault near Cedarville. A Bayesian OxCal analysis of timing constraints indicates earthquake times of 18.2 ± 2.6, 10.9 ± 3.2, 8.5 ± 0.5, 5.8 ± 1.5, and 1.2 ± 0.1 ka. These data yield recurrence intervals of 7.3 ± 4.1, 2.5 ± 3.2, 2.7 ± 1.6, and 4.5 ± 1.5 ka and an elapsed time of 1.2 ± 0.1 ka since the latest surface-rupturing earthquake. Our best estimate of latest Quaternary vertical slip rate is 0.6 ?? 0.1 mm/a. This late Quaternary rate is remarkably similar to long-term (8-14 Ma) minimum vertical slip rates (>0.4-0.5 ± 0.3 mm/a) calculated from recently acquired seismic reflection and chronologic and structural data in Surprise Valley and the adjacent Warner Mountains. However, our slip rate yields estimates of extension that are lower than recent campaign GPS determinations by factors of 1.5-4 unless the fault has an unusually shallow (30°-35°) dip as suggested by recently acquired seismic reflection data. Coseismic displacements of 2-4.5 ± 1 m documented in the trench and probable rupture lengths of 53-65 km indicate a history of latest Quaternary earthquakes of M 6.8-7.3 on the central part of the. Surprise Valley fault.

Structural fabrics, mineralization and Lamaride kinematics of the Idaho Springs-Ralston shear zone, Colorado mineral belt and central Front Range uplift

USGS Publications Warehouse

Caine, Jonathan S.; Nelson, E.P.; Beach, S.T.; Layer, P.W.

2006-01-01

The Idaho Springs and Central City mining districts form the central portion of a structurally controlled hydrothermal precious- and base-metal vein system in the Front Range of the northeast-trending Colorado Mineral Belt. Three new 40Ar/39Ar plateau ages on hydrothermal sericite indicate the veins formed during the Laramide orogeny between 65.4??1.5 - 61.9??1.3 Ma. We compile structural geologic data from surface geological maps, subsurface mine maps, and theses for analysis using modern graphical methods and integration into models of formation of economic mineral deposits. Structural data sets, produced in the 1950s and 1960s by the U.S. Geological Survey, are compiled for fabric elements, including metamorphic foliations, fold axial trends, major brittle fault zones, quartz and precious- and base-metal veins and fault veins, Tertiary dikes, and joints. These fabric elements are plotted on equal-area projections and analyzed for mean fabric orientations. Strike-slip fault-vein sets are mostly parallel or sub-parallel, and not conjugate as interpreted by previous work; late-stage, normal-slip fault veins possibly show a pattern indicative of triaxial strain. Fault-slip kinematic analysis was used to model the trend of the Laramide maximum horizontal stress axis, or compression direction, and to determine compatibility of opening and shear motions within a single stress field. The combined-model maximum compression direction for all strike slip fault veins is ???068??, which is consistent with published Laramide compression directions of ???064?? (mean of 23 regional models) and ???072?? for the Front Range uplift. The orientations of fabric elements were analyzed for mechanical and kinematic compatibility with opening, and thus permeability enhancement, in the modeled regional east-northeast, Laramide compression direction. The fabric orientation analysis and paleostress modeling show that structural permeability during mineralization was enhanced along pre-existing metamorphic foliations and fold axial planes. Large orientation dispersion in most fabric elements likely caused myriad potential pathways for permeability. The dominant orientations of opening and shear mode structures are consistent with a sub-parallel network of structures that formed in the Laramide east-northeast compression direction. The results presented demonstrate the importance of using mechanical and kinematic theory integrated with contemporary ideas of permeability structure to better understand the coupled nature of fluid flow, mineral deposition, stress, and strain. Further, the results demonstrate that there is significant internal strain within this basement-cored uplift that was localized by optimally oriented pre-existing structures in a regional stress field.

Digital tabulation of stratigraphic data from oil and gas wells in Cuyama Valley and surrounding areas, central California

USGS Publications Warehouse

Sweetkind, Donald S.; Bova, Shiera C.; Langenheim, V.E.; Shumaker, Lauren E.; Scheirer, Daniel S.

2013-01-01

Stratigraphic information from 391 oil and gas exploration wells from Cuyama Valley, California, and surrounding areas are herein compiled in digital form from reports that were released originally in paper form. The Cuyama Basin is located within the southeasternmost part of the Coast Ranges and north of the western Transverse Ranges, west of the San Andreas fault. Knowledge of the location and elevation of stratigraphic tops of formations throughout the basin is a first step toward understanding depositional trends and the structural evolution of the basin through time, and helps in understanding the slip history and partitioning of slip on San Andreas and related faults.

Crustal Deformation of the Central Walker Lane from GPS velocities: Block Rotations and Slip Rates

NASA Astrophysics Data System (ADS)

Bormann, J. M.; Hammond, W. C.; Kreemer, C. W.; Blewitt, G.; Wesnousky, S. G.

2010-12-01

The Walker Lane is a complex zone of active intracontinental transtension between the Sierra Nevada/Great Valley (SNGV) microplate and the Basin and Range in the western United States. Collectively, this ~100 km wide zone accommodates ~20% of the Pacific-North American relative plate motion. The Central Walker Lane (CWL) extends from the southern boundary of the Mina Deflection (~38.0°N) to the latitude of Lake Tahoe (~39.5°N) and encompasses the transition from Basin and Range style faulting in the east to the stable block motion of the SNGV microplate in the West. We combine GPS data from the Mobile Array of GPS for Nevada Transtension (MAGNET, http://geodesy.unr.edu/networks) with continuous observations from the EarthScope Plate Boundary Observatory to solve for rates of crustal deformation in the CWL through a block modeling approach. The GPS coordinate time series are derived in this region as part of a 7000-station global network solution using the latest JPL reanalysis of GPS orbits, and the latest antenna models for stations and satellites. The data were processed by precise point positioning using JPL's GIPSY OASIS II software followed by our custom Ambizap3 software, to produce a globally-consistent, ambiguity-resolved network solution. GPS time series in the western United States are rotated into a North America-fixed reference frame and are spatially filtered with respect to the secular motions of reference stations that demonstrate long-term secular stability. In the study region, we use 130 GPS velocities that are corrected for viscoelastic postseismic relaxation following 19th and 20th century earthquakes in the Central Nevada Seismic Belt to constrain rates of long-term fault slip and block rotation. The spatial density and precision of our velocity field (average station spacing of ~20 km with uncertainties well below 1 mm/yr) allow us to compare geodetically estimated slip rates with geologic observations as well as address specific questions about how shear is transferred from the Southern Walker Lane through the Mina Deflection and evaluate along-strike variation of the slip rate on the Sierra Nevada range front fault. Preliminary results confirm a pattern of deformation consistent with geological observations. Deformation zones are characterized by 1) left-lateral slip on east-northeast trending faults and clockwise block rotations in the Mina Deflection, 2) right-lateral slip on northwest trending faults along the eastern margin of the CWL, 3) east-west extension along north trending faults in the western portion of the CWL with right lateral slip increasing toward the SNGV microplate boundary, 4) clockwise rotation of blocks in the Carson Domain, and 5) northwest directed extension in the Basin and Range. Estimates of fault slip rates along the eastern boundary of the SNGV block find that slip is oblique with preliminary rates ranging between 0.4-0.8(±0.1) mm/yr horizontal extension and 0.9-1.5(±0.1) mm/yr right lateral.

Kinematic vicissitudes and the spatial distribution of the alteration zone related to the Byobuyama fault, central Japan. (Implication; Influence of another faults.)

NASA Astrophysics Data System (ADS)

Katori, T.; Kobayashi, K.

2015-12-01

The central Japan is one of the most concentrated area of active faults (Quaternary fault). These are roughly classified into two orthogonally-oriented fault sets of NE-SW and NW-SE strikes. The study area is located in Gifu prefecture, central Japan. In there, the basement rocks are composed mainly of Triassic-Jurassic accretionary prism (Mino belt), Cretaceous Nohi Rhyolite and Cretaceous granitic rocks. Miocene Mizunami G. and Pliocene-Pleistocene Toki Sand and Gravel F. unconformably cover the basement rocks. The Byobuyama fault, 32 km in length, is NE-SW strike and displaces perpendicularly the Toki Sand and Gravel F. by 500 m. The northeastern terminal of the fault has contact with the southern terminal of the Atera fault of NW-SE strike and offset their displacements each other. It is clear that the activity of the Byobuyama fault plays a role of the development of the complicated fault geometry system in the central Japan. In this study, we performed a broad-based investigation along the Byobuyama fault and collected samples. Actually, we observed 400 faults and analyzed 200 fault rocks. Based on these results, we obtained the following new opinion. 1. The Byobuyama fault has experienced following activities that can be divided to 3 stages at least under different stress field. 1) Movement with the sinisterly sense (preserved in cataclasite zone). 2) Dextral movement (preserved in fault gouge zone). 3) Reverse fault movement (due to the aggressive rise of mountains). In addition, the change from Stage 2 to Stage 3 is a continuous. 2. There is a relationship between the distance from the trace of the Byobuyama fault and the combination of alteration minerals included in the fault rocks. 3. In the central part of the Byobuyama fault (CPBF), fault plane trend and combination of alteration minerals shows specific features. The continuous change is considered to mean the presence of factors that interfere with the dextral movement of the Byobuyama fault. What is considered as one of the factors is the effect of the fault zone adjacent, especially the Atera fault. CPBF is located just southeast extension of the Akou fault, NW-SE strike. We think that this extension reaches up to CPBF. Based on the above, we make a presentation about interaction of two faults from the point of view of kinematic vicissitudes and alteration process.

Evolution of triangular topographic facets along active normal faults

NASA Astrophysics Data System (ADS)

Balogun, A.; Dawers, N. H.; Gasparini, N. M.; Giachetta, E.

2011-12-01

Triangular shaped facets, which are generally formed by the erosion of fault - bounded mountain ranges, are arguably one of the most prominent geomorphic features on active normal fault scarps. Some previous studies of triangular facet development have suggested that facet size and slope exhibit a strong linear dependency on fault slip rate, thus linking their growth directly to the kinematics of fault initiation and linkage. Other studies, however, generally conclude that there is no variation in triangular facet geometry (height and slope) with fault slip rate. The landscape of the northeastern Basin and Range Province of the western United States provides an opportunity for addressing this problem. This is due to the presence of well developed triangular facets along active normal faults, as well as spatial variations in fault scale and slip rate. In addition, the Holocene climatic record for this region suggests a dominant tectonic regime, as the faulted landscape shows little evidence of precipitation gradients associated with tectonic uplift. Using GIS-based analyses of USGS 30 m digital elevation data (DEMs) for east - central Idaho and southwestern Montana, we analyze triangular facet geometries along fault systems of varying number of constituent segments. This approach allows us to link these geometries with established patterns of along - strike slip rate variation. For this study, we consider major watersheds to include only catchments with upstream and downstream boundaries extending from the drainage divide to the mapped fault trace, respectively. In order to maintain consistency in the selection criteria for the analyzed triangular facets, only facets bounded on opposite sides by major watersheds were considered. Our preliminary observations reflect a general along - strike increase in the surface area, average slope, and relief of triangular facets from the tips of the fault towards the center. We attribute anomalies in the along - strike geometric measurements of the triangular facets to represent possible locations of fault segment linkage associated with normal fault evolution.

The structural inventory of a small complex impact crater: Jebel Waqf as Suwwan, Jordan

NASA Astrophysics Data System (ADS)

Kenkmann, Thomas; Sturm, Sebastian; Krüger, Tim; Salameh, Elias; Al-Raggad, Marwan; Konsul, Khalil

2017-07-01

The investigation of terrestrial impact structures is crucial to gain an in-depth understanding of impact cratering processes in the solar system. Here, we use the impact structure Jebel Waqf as Suwwan, Jordan, as a representative for crater formation into a layered sedimentary target with contrasting rheology. The complex crater is moderately eroded (300-420 m) with an apparent diameter of 6.1 km and an original rim fault diameter of 7 km. Based on extensive field work, IKONOS imagery, and geophysical surveying we present a novel geological map of the entire crater structure that provides the basis for structural analysis. Parametric scaling indicates that the structural uplift (250-350 m) and the depth of the ring syncline (<200 m) are anomalously low. The very shallow relief of the crater along with a NE vergence of the asymmetric central uplift and the enhanced deformations in the up-range and down-range sectors of the annular moat and crater rim suggest that the impact was most likely a very oblique one ( 20°). One of the major consequences of the presence of the rheologically anisotropic target was that extensive strata buckling occurred during impact cratering both on the decameter as well as on the hundred-meter scale. The crater rim is defined by a circumferential normal fault dipping mostly toward the crater. Footwall strata beneath the rim fault are bent-up in the down-range sector but appear unaffected in the up-range sector. The hanging wall displays various synthetic and antithetic rotations in the down-range sector but always shows antithetic block rotation in the up-range sector. At greater depth reverse faulting or folding is indicated at the rim indicating that the rim fault was already formed during the excavation stage.

Paleomagnetic and Seismologic Evidence for Oblique-Slip Partitioning to the Coalinga Anticline From the San Andreas Fault

NASA Astrophysics Data System (ADS)

Tetreault, J. L.; Jones, C. H.

2007-12-01

The Coalinga Anticline is a one of a series of fault-related folds in the central Coast Ranges, California, oriented subparallel to the San Andreas Fault (SAF). The development of the Central Coast Range anticlines can be related to the relative strength of the SAF. If positing a weak SAF, fault-normal slip is partitioned to these subparallel compressional folds. If the SAF is strong, these folds rotated to their current orientation during wrenching. Another possibility is that the Coast Range anticlines are accommodating oblique-slip partitioned from the SAF. The 1983 Coalinga earthquake does not have a purely thrusting focal mechanism (rake =100°), reflecting the likelihood that oblique slip is being partitioned to this anticline, even though surface expression of fold-axis-parallel slip has not been identified. Paleomagnetic vertical-axis rotations and focal mechanism strain inversions were used to quantify oblique-slip deformation within the Coalinga Anticline. Clockwise rotations of 10° to 16° are inferred from paleomagnetic sites located in late Miocene to Pliocene beds on the steeply dipping forelimb and backlimb of the fold. Significant vertical-axis rotations are not identified in the paleomagnetic sites within the nose of the anticline. The varying vertical axis rotations conflict with wrench tectonics (strong SAF) as the mechanism of fold development. We use focal mechanisms inversions of earthquakes that occurred between 1983 to 2006 to constrain the seismogenic strain within the fold that presumably help to build it over time. In the upper 7 km, the principal shortening axis is oriented N37E to N40E, statistically indistinguishable from normal to the fold (N45E). The right-lateral shear in the folded strata above the fault tip, evident from the paleomagnetically determined clockwise vertical-axis rotations, is being accommodated aseismically or interseismically. In the region between 7 and 11 km, where the mainshock occurred, the shortening direction ranges from oblique to normal to the fold trend. Our results show that right-lateral slip is resolved along the main fault plane and not distributed to the smaller aftershocks at depths of 7-11 km. The principal strain axes and clockwise paleomagnetic rotations indicate that the Coalinga Anticline is accommodating minor right-lateral shearing and thus shares some of the strike-slip motion of the San Andreas system.

Did the Malaysian Main Range record a weak hot Mega Shear?

NASA Astrophysics Data System (ADS)

Sautter, Benjamin; Pubellier, Manuel

2015-04-01

The Main Range of Peninsular Malaysia is a batholith that extends over more than 500km from Malacca in the South to the Thailand border in the North. It results from the subduction/accretion history of the western margin of Sunda Plate by Late Triassic times. We present a structural analysis based on geomorphology, field observations and geochronological data. While most of the basement fabrics are characterized by N-S structures such as granitic plutons, sutures, and folds, a prominent oblique deformation occurred by the End of the Mesozoics synchronous with a widespread thermal anomaly (eg Tioman, Stong, Gunung Jerai, Khanom, Krabi plutons). Morphostructures and drainage anomalies from Digital Elevation Model (SRTM and ASTER), allow us to highlight 2 major groups of penetrative faults in the Central Range Batholith: early NW-SE (5km spaced faults some of which are identified as thrust faults) cross-cut and offset by NNE-SSW dextral normal faults. The regularly spaced NW-SE faults bend toward the flanks of the Batholith and tend to parallel both the Bentong Raub Suture Zone to the East and the strike slip Bok Bak Fault to the West, thus giving the overall fault network the aspect of a large C/S band. Hence, a ductile/brittle behavior can be proposed for the sigmoid faults in the core of the Batholith, whereas the NNE faults are clearly brittle, more linear and are found on the smaller outlying plutons. Radiogenic crystallization ages are homogenous at 190±20Ma (U-Pb Zircon, Tc>1000°C and K-Ar Muscovite, Tc350°C) whereas Zircon fission tracks(Tc=250°C) show specific spatial zoning of the data distribution with ages at 100±10Ma for the outlying plutons and ages at 70±10Ma for the Main Range. We propose a structural mechanism according to which the Main Range would be the ductile core of a Mega-Shear Zone exhumed via transpressive tectonics by the end of Mesozoic Times. A first stage between 100 and 70Ma (Upper Cretaceous) of dextral transpression affected Peninsular Malaysia at a lithospheric scale, accommodated by N-S faults (C planes) such as the Bentong Raub Suture Zone, the Bukit Tinggi fault and the Kledang Fault. This lead to the formation of NW-SE fractures in already exhumed peripheral plutons (< 250°C) and deep level (> 250°C) sigmoid faults (S planes) in the Main range. Later a brittle stage of exhumation occurred in the same system, after 70Ma, leading to NNE-SSW dextral Riedel type faults reactivating pluton flanks, and offsetting older faults as well as quartz dykes. The occurrence of such a structure could be linked to the subduction of the Wharton Ridge at the western margin of Sunda Plate. As a result, a collapse of this hot and thin crust occurred accommodated by LANF's reactivating the basement fabrics including intrusive edges and folds hinges.

A 15 year catalog of more than 1 million low-frequency earthquakes: Tracking tremor and slip along the deep San Andreas Fault

NASA Astrophysics Data System (ADS)

Shelly, David R.

2017-05-01

Low-frequency earthquakes (LFEs) are small, rapidly recurring slip events that occur on the deep extensions of some major faults. Their collective activation is often observed as a semicontinuous signal known as tectonic (or nonvolcanic) tremor. This manuscript presents a catalog of more than 1 million LFEs detected along the central San Andreas Fault from 2001 to 2016. These events have been detected via a multichannel matched-filter search, cross-correlating waveform templates representing 88 different LFE families with continuous seismic data. Together, these source locations span nearly 150 km along the central San Andreas Fault, ranging in depth from 16 to 30 km. This accumulating catalog has been the source for numerous studies examining the behavior of these LFE sources and the inferred slip behavior of the deep fault. The relatively high temporal and spatial resolutions of the catalog have provided new insights into properties such as tremor migration, recurrence, and triggering by static and dynamic stress perturbations. Collectively, these characteristics are inferred to reflect a very weak fault likely under near-lithostatic fluid pressure, yet the physical processes controlling the stuttering rupture observed as tremor and LFE signals remain poorly understood. This paper aims to document the LFE catalog assembly process and associated caveats, while also updating earlier observations and inferred physical constraints. The catalog itself accompanies this manuscript as part of the electronic supplement, with the goal of providing a useful resource for continued future investigations.

The application of active-source seismic imaging techniques to transtensional problems the Walker Lane and Salton Trough

NASA Astrophysics Data System (ADS)

Kell, Anna Marie

The plate margin in the western United States is an active tectonic region that contains the integrated deformation between the North American and Pacific plates. Nearly focused plate motion between the North American and Pacific plates within the northern Gulf of California gives way north of the Salton Trough to more diffuse deformation. In particular a large fraction of the slip along the southernmost San Andreas fault ultimately bleeds eastward, including about 20% of the total plate motion budget that finds its way through the transtensional Walker Lane Deformation Belt just east of the Sierra Nevada mountain range. Fault-bounded ranges combined with intervening low-lying basins characterize this region; the down-dropped features are often filled with water, which present opportunities for seismic imaging at unprecedented scales. Here I present active-source seismic imaging from the Salton Sea and Walker Lane Deformation Belt, including both marine applications in lakes and shallow seas, and more conventional land-based techniques along the Carson range front. The complex fault network beneath the Salton Trough in eastern California is the on-land continuation of the Gulf of California rift system, where North American-Pacific plate motion is accommodated by a series of long transform faults, separated by small pull-apart, transtensional basins; the right-lateral San Andreas fault bounds this system to the north where it carries, on average, about 50% of total plate motion. The Salton Sea resides within the most youthful and northerly "spreading center" in this several thousand-kilometer-long rift system. The Sea provides an ideal environment for the use of high-data-density marine seismic techniques. Two active-source seismic campaigns in 2010 and 2011 show progression of the development of the Salton pull-apart sub-basin and the northerly propagation of the Imperial-San Andreas system through time at varying resolutions. High fidelity seismic imagery documents the timing of strain transfer from the Imperial fault onto the San Andreas fault through the application of sequence stratigraphy. Evidence shows that the formation of the Salton and Mesquite sub-basins and the associated change of strain partitioning occurred within the last 20-40 k.y., essentially modifying a broader zone of transtension bounding the Imperial and San Andreas faults into two smaller zones of focused extension. The north-central Walker Lane contains a diffuse network of both strike-slip and normal faults, with some degree of strain partitioning characterized by normal faulting to the west along the eastern edge of the Sierra Nevada mountain range, and strike-slip faults to the east that define a diffuse boundary against the Basin and Range proper. A seismic study across the Mount Rose fault zone, bounding the Carson Range near Reno, Nevada, was carried out to investigate slip across a potential low-angle normal fault. A hammer seismic reflection and refraction profile combined with airborne LiDAR (light detection and ranging) imagery highlights fault scarp modification through minor slumping/landslides, providing a better understanding of the nature of slip on this fault. The northeastern margin of the Walker Lane is a region where both "Basin and Range" style normal faults and dextral strike-slip faults contribute to the northward propagation of the Walker Lane (essentially parallel to an equivalent northward propagation of the Mendocino triple junction). Near this intersection lies Pyramid Lake, bounded to the southwest by the dextral Pyramid Lake fault and to the northeast by the normal Lake Range fault. A high-resolution (sub-meter) seismic CHIRP survey collected in 2010 shows intriguing relationships into fault architecture beneath Pyramid Lake. Over 500 line-km of seismic data reveal a polarity flip in basin structure as down-to-the-east motion at the northern end of the Pyramid Lake fault rapidly gives way to down-to-the-west normal motion along the Lake Range fault. Alternating patterns of asymmetric and symmetric stratal patterns west of the Lake Range fault provides some evidence for segmentation of total slip along this large normal fault. Using dated sediment cores, slip rate for the Lake Range fault was found to be approximately 1 mm/yr during the Holocene. A complex zone of transtenstion was also observed in seismic CHIRP data in the northwest quadrant of the lake, where short, discontinuous faults hint at the development of a nascent shear zone trending to the northwest. (Abstract shortened by UMI.)

Active tectonics and strain partitioning along dextral fault system in Central Iran: Analysis of geomorphological observations and geophysical data in the Kashan region

NASA Astrophysics Data System (ADS)

Jamali, Farshad; Hessami, Khaled; Ghorashi, Manoochehr

2011-03-01

This paper uses high-resolution images and field investigations, in conjunction with seismic reflection data, to constrain active structural deformation in the Kashan region of Central Iran. Offset stream beds and Qanats indicate right-lateral strike slip motion at a rate of about 2 mm/yr along the NW-SE trending Qom-Zefreh fault zone which has long been recognized as one of the major faults in Central Iran. However, the pattern of drainage systems across the active growing folds including deep incision of stream beds and deflected streams indicate uplift at depth on thrust faults dipping SW beneath the anticlines. Therefore, our studies in the Kashan region indicate that deformation occurs within Central Iran which is often considered to behave as a non-deforming block within the Arabia-Eurasia collision zone. The fact that the active Qom-Zefreh strike-slip fault runs parallel to the active folds, which overlie blind thrust faults, suggests that oblique motion of Arabia with respect to Eurasia is partitioned in this part of Central Iran.

Fault weakening and earthquake instability by powder lubrication

USGS Publications Warehouse

Reches, Z.; Lockner, D.A.

2010-01-01

Earthquake instability has long been attributed to fault weakening during accelerated slip1, and a central question of earthquake physics is identifying the mechanisms that control this weakening2. Even with much experimental effort2-12, the weakening mechanisms have remained enigmatic. Here we present evidence for dynamic weakening of experimental faults that are sheared at velocities approaching earthquake slip rates. The experimental faults, which were made of room-dry, solid granite blocks, quickly wore to form a fine-grain rock powder known as gouge. At modest slip velocities of 10-60mms-1, this newly formed gouge organized itself into a thin deforming layer that reduced the fault's strength by a factor of 2-3. After slip, the gouge rapidly 'aged' and the fault regained its strength in a matter of hours to days. Therefore, only newly formed gouge can weaken the experimental faults. Dynamic gouge formation is expected to be a common and effective mechanism of earthquake instability in the brittle crust as (1) gouge always forms during fault slip5,10,12-20; (2) fault-gouge behaves similarly to industrial powder lubricants21; (3) dynamic gouge formation explains various significant earthquake properties; and (4) gouge lubricant can form for a wide range of fault configurations, compositions and temperatures15. ?? 2010 Macmillan Publishers Limited. All rights reserved.

Elasto-plastic deformation and plate weakening due to normal faulting in the subducting plate along the Mariana Trench

NASA Astrophysics Data System (ADS)

Zhou, Zhiyuan; Lin, Jian

2018-06-01

We investigated variations in the elasto-plastic deformation of the subducting plate along the Mariana Trench through an analysis of flexural bending and normal fault characteristics together with geodynamic modeling. Most normal faults were initiated at the outer-rise region and grew toward the trench axis with strikes mostly subparallel to the local trench axis. The average trench relief and maximum fault throws were measured to be significantly greater in the southern region (5 km and 320 m, respectively) than the northern and central regions (2 km and 200 m). The subducting plate was modeled as an elasto-plastic slab subjected to tectonic loading at the trench axis. The calculated strain rates and velocities revealed an array of normal fault-like shear zones in the upper plate, resulting in significant faulting-induced reduction in the deviatoric stresses. We then inverted for solutions that best fit the observed flexural bending and normal faulting characteristics, revealing normal fault penetration to depths of 21, 20, and 32 km beneath the seafloor for the northern, central, and southern regions, respectively, which is consistent with the observed depths of the relocated normal faulting earthquakes in the central Mariana Trench. The calculated deeper normal faults of the southern region might lead to about twice as much water being carried into the mantle per unit trench length than the northern and central regions. We further calculated that normal faulting has reduced the effective elastic plate thickness Te by up to 52% locally in the southern region and 33% in both the northern and central regions. The best-fitting solutions revealed a greater apparent angle of the pulling force in the southern region (51-64°) than in the northern (22-35°) and central (20-34°) regions, which correlates with a general southward increase in the seismically-determined dip angle of the subducting slab along the Mariana Trench.

Trench investigation along the Merida section of the Bocono fault (central Venezuelan Andes), Venezuela

USGS Publications Warehouse

Audemard, F.; Pantosti, D.; Machette, M.; Costa, C.; Okumura, K.; Cowan, H.; Diederix, H.; Ferrer, C.

1999-01-01

The Bocono fault is a major NE-SW-trending, dextral fault that extends for about 500 km along the backbone of the Venezuelan Andes. Several large historical earthquakes in this region have been attributed to the Bocono fault, and some of these have been recently associated with specific parts through paleoseismologic investigations. A new trench study has been performed, 60 km to the northeast of Merida in the central Venezuelan Andes, where the fault forms a releasing bend, comprising two conspicuous late Holocene fault strands that are about 1 km apart. The southern and northern strands carry about 70% and 30% (respectively) of the 7-10 mm/yr net slip rate measured in this sector, which is based on a 40 vs. 85-100 m right-lateral offset of the Late Pleistocene Los Zerpa moraines. A trench excavated on the northern strand of the fault (near Morros de los Hoyos, slightly northeast of Apartaderos) across a twin shutter ridge and related sag pond exposed two main fault zones cutting Late Pleistocene alluvial and Holocene peat deposits. Each zone forms a shutter ridge with peat deposits ponded against the uplifted block. The paleoearthquake reconstruction derived from this trench allow us to propose the occurrence of at least 6-8 earthquakes in the past 9000 yr, yielding a maximum average recurrence interval of about 1100-1500 yr. Based on the northern strands average slip rate (2.6 mm/yr), such as earthquake sequence should have accommodated about 23 m of slip since 9 ka, suggesting that the maximum slip per event ranges between 3 and 4 m. No direct evidence for the large 1812 earthquake has been found in the trench, although this earthquake may have ruptured this section of the fault. Further paleoseismic studies will investigate the possibility that this event occurred in the Bocono fault, but ruptured mainly its southern strand in this region.

A structural transect across the Mongolian Western Altai: Active transpressional mountain building in central Asia

NASA Astrophysics Data System (ADS)

Dickson Cunningham, W.; Windley, Brian F.; Dorjnamjaa, D.; Badamgarov, G.; Saandar, M.

1996-02-01

We present results from the first detailed geological transect across the Mongolian Western Altai using modern methods of structural geology and fault kinematic analysis. Our purpose was to document the structures responsible for Cenozoic uplift of the range in order to better understand processes of intracontinental mountain building. Historical right-lateral strike-slip and oblique-slip earthquakes have previously been documented from the Western Altai, and many mountain fronts are marked by active fault scarps indicating current tectonic activity and uplift. The dominant structures in the range are long (>200 km) NNW trending right-lateral strike-slip faults. Our transect can be divided into three separate domains that contain active, right-lateral strike-slip master faults and thrust faults with opposing vergence. The current deformation regime is thus transpressional. Each domain has an asymmetric flower structure cross-sectional geometry, and the transect as a whole is interpreted as three separate large flower structures. The mechanism of uplift along the transect appears to be horizontal and vertical growth of flower structures rooted into the dominant right-lateral strike-slip faults. The major Bulgan Fault forms the southern structural boundary to the range and is a 3.5-km-wide brittle-ductile zone that has accommodated reverse and left-lateral strike-slip displacements. It appears to be linked to the North Gobi Fault Zone to the east and Irtysh Fault zone to the west and thus may be over 900 km in length. Two major ductile left-lateral extensional shear zones were identified in the interior of the range that appear to be preserved structures related to a regional Paleozoic or Mesozoic extensional event. Basement rocks along the transect are dominantly metavolcanic, metasedimentary, or intrusive units probably representing a Paleozoic accretionary prism and arc complex. The extent to which Cenozoic uplift has been accommodated by reactivation of older structures and inversion of older basins is unknown and will require further study. As previously suggested by others, Cenozoic uplift of the Altai is interpreted to be due to NE-SW directed compressional stress resulting from the Indo-Eurasian collision 2500 km to the south.

Deformation and seismicity of Taiwan.

PubMed

Vita-Finzi, C

2000-10-10

14C-dated Holocene coastal uplift, conventional and satellite geodetic measurements, and coseismic and aseismic fault slip reveal the pattern of distributed deformation at Taiwan resulting from convergence between the Philippine Sea plate and Eurasia; as in other subduction orogenic settings, the locus of strain release and accumulation is strongly influenced by changes in fault geometry across strike. Uplift evidence from the islands of Lutao and Lanhsu is consistent with progressive oblique collision between the Luzon arc and the Chinese continental margin. In the Coastal Range, geodetic and seismic records show that shortening is taken up serially by discontinuous slip on imbricate faults. The geodetic data point to net extension across the Central Range, but deformed Holocene shorelines in the Hengchun Peninsula at its southern extremity suggest that the extension is a superficial effect partly caused by blind reverse faulting. The fastest shortening rates indicated by geodesy are recorded on the Longitudinal Valley fault and across the Chukou fault within the fold-and-thrust belt. In the former, the strain is dissipated mainly as aseismic reverse and strike-slip displacement. In contrast, the fold-and-thrust belt has witnessed five earthquakes with magnitudes of 6.5 or above in the 20th century, including the 1999.9.21 Chi-Chi earthquake (magnitude approximately 7.6) on a branch of the Chukou fault. The neotectonic and geodetic data for Taiwan as a whole suggest that the fold-and-thrust belt will continue to host the majority of great earthquakes on the island.

The tectonic evolution of western Central Iran seen through detrital white mica

NASA Astrophysics Data System (ADS)

Kargaranbafghi, Fariba; Neubauer, Franz; Genser, Johann

2015-05-01

A first order survey of 40Ar/39Ar dating of detrital white mica from Jurassic to Pliocene sandstones has been carried out in order to reveal the tectonic evolution of blocks in Central Iran. The Central Iran block was believed to represent a stable Precambrian block. Our results indicate that: (1) Only a very small proportion of Precambrian but abundant Paleozoic and Mesozoic detrital white mica indicate the Phanerozoic, mostly Mesozoic age of metamorphic crust exposed in Central Iran. The oldest but scarce detrital white mica grains have ages ranging from 524 to 826 Ma heralding a Late Precambrian and Cambrian crystalline basement or cannibalism from older clastic successions. (2) Jurassic and Cretaceous sandstones from the west and east of the Chapedony fault yield different age spectra, with a dominance of Variscan ages (ca. 308-385 Ma) in the Biabanak unit west of the Chapedony fault compared to coeval sandstones from the block east of the Chapedony fault, where Variscan ages are subordinate and Cimmerian ages predominate. The micas from the Biabanak unit are most likely derived from the Variscan accretionary complex exposed in the Anarak-Jandaq areas further northwest. This result underlines the importance of a major block boundary identified as the Chapedony fault, which is in extension of a fault previously proposed. (3) Two stages of Cimmerian events are visible in our data set from Cretaceous and Paleogene sandstones, a cluster around 170 Ma and at ca. 205 Ma. These clusters suggest a two-stage Cimmerian evolution of the largely amphibolite-grade metamorphic Posht-e-Badam and Boneh Shurow complexes. (4) The youngest micas in Paleogene conglomerates have an age of ca. 100 Ma and are most likely derived from the base of the Posht-e-Badam complex. No record of the uplifted Eocene Chapedony metamorphic core complex has been found in Eocene and Pliocene clastic rocks.

Structure, Quaternary history, and general geology of the Corral Canyon area, Los Angeles County, California

USGS Publications Warehouse

Yerkes, R.F.; Wentworth, Carl M.

1965-01-01

The Corral Canyon nuclear power plant site consists of about 305 acres near the mouth of Corral Canyon in the central Santa Monica Mountains; it is located on an east-trending segment of the Pacific Coast between Point Dume and Malibu Canyon, about 28 miles due west of Los Angeles. The Santa Monica Mountains are the southwesternmost mainland part of the Transverse Ranges province, the east-trending features of which transect the otherwise relatively uniform northwesterly trend of the geomorphic and geologic features of coastal California. The south margin of the Transverse Ranges is marked by the Santa Monica fault system, which extends eastward near the 34th parallel for at least 145 miles from near Santa Cruz Island to the San Andreas fault zone. In the central Santa Monica Mountains area the Santa Monica fault system includes the Malibu Coast fault and Malibu Coast zone of deformation on the north; from the south it includes an inferred fault--the Anacapa fault--considered to follow an east-trending topographic escarpmemt on the sea floor about 5 miles south of the Malibu Coast fault. The low-lying terrain south of the fault system, including the Los Angeles basin and the largely submerged Continental Borderland offshore, are dominated by northwest-trending structural features. The Malibu Coat zone is a wide, east-trending band of asymmetrically folded, sheared, and faulted bedrock that extends for more than 20 miles along the north margin of the Santa Monica fault system west of Santa Monica. Near the north margin of the Malibu Coast zone the north-dipping, east-trending Malibu Coast fault juxtaposes unlike, in part contemporaneous sedimentary rock sections; it is inferred to be the near-surface expression of a major crustal boundary between completely unrelated basement rocks. Comparison of contemporaneous structural features and stratigraphic sections (Late Cretaceous to middle Miocene sedimentary, rocks and middle Miocene volcanic and intrusive igneous rocks on the north; middle and upper Miocene sedimentary and middle Miocene volcanic rocks on the south) across the fault demonstrates that neither strike slip of less than 25 miles nor high-angle dip slip can account for this juxtaposition. Instead, the Malibu Coast fault is inferred to have been the locus of large-magnitude, north-south oriented, horizontal shortening (north, or upper, block thrust over south block). This movement occurred at or near the northern boundary of the Continental Borderland, the eastern boundary of which is inferred to be the northwest-trending known-active Newport-Inglewood zone of en echelon right lateral strike-slip faults in the western Los Angeles basin. Local structural features and their relation to regional features, such as those in the Malibu Coast zone, form the basis for the interpretation that the Malibu Coast fault has acted chiefly as a thrust fault. Within the Malibu Coast zone, on both sides of the Malibu Coast fault, structural features in rocks that range in age from Late Cretaceous to late Miocene are remarkably uniform in orientation. The predominant trend of bedding, axial surfaces of numerous asymmetric folds, locally pervasive shear surfaces, and faults is approximately east-west and their predominant dip is northward.. The axes of the folds plunge gently east or west. Evidence from faults and shears within the zone indicates that relative movement on most of these was north (upper) over south. Beyond the Malibu Coast zone to the north and south the rocks entirely lack the asymmetric folds, overturned beds, and the locally abundant shears that characterize the rocks within the zone; these rocks were therefore not subjected to the same deforming forces that existed near the Malibu Coast fault. Movement on the Malibu Coast fault and deformation in the Malibu Coast zone occurred chiefly during the interval between late Miocene and late Pleistocene time. The youngest-known faulting in the Malibu Coast zone is late Pl

The Non-Regularity of Earthquake Recurrence in California: Lessons From Long Paleoseismic Records in Simple vs Complex Fault Regions (Invited)

NASA Astrophysics Data System (ADS)

Rockwell, T. K.

2010-12-01

A long paleoseismic record at Hog Lake on the central San Jacinto fault (SJF) in southern California documents evidence for 18 surface ruptures in the past 3.8-4 ka. This yields a long-term recurrence interval of about 210 years, consistent with its slip rate of ~16 mm/yr and field observations of 3-4 m of displacement per event. However, during the past 3800 years, the fault has switched from a quasi-periodic mode of earthquake production, during which the recurrence interval is similar to the long-term average, to clustered behavior with the inter-event periods as short as a few decades. There are also some periods as long as 450 years during which there were no surface ruptures, and these periods are commonly followed by one to several closely-timed ruptures. The coefficient of variation (CV) for the timing of these earthquakes is about 0.6 for the past 4000 years (17 intervals). Similar behavior has been observed on the San Andreas Fault (SAF) south of the Transverse Ranges where clusters of earthquakes have been followed by periods of lower seismic production, and the CV is as high as 0.7 for some portions of the fault. In contrast, the central North Anatolian Fault (NAF) in Turkey, which ruptured in 1944, appears to have produced ruptures with similar displacement at fairly regular intervals for the past 1600 years. With a CV of 0.16 for timing, and close to 0.1 for displacement, the 1944 rupture segment near Gerede appears to have been both periodic and characteristic. The SJF and SAF are part of a broad plate boundary system with multiple parallel strands with significant slip rates. Additional faults lay to the east (Eastern California shear zone) and west (faults of the LA basin and southern California Borderland), which makes the southern SAF system a complex and broad plate boundary zone. In comparison, the 1944 rupture section of the NAF is simple, straight and highly localized, which contrasts with the complex system of parallel faults in southern California. These observations suggest that the complexity of the southern California fault network is partly responsible for the apparent increase in “noise” and non-periodic behavior, perhaps resulting from stress transfer to adjacent faults after a large earthquake on one fault. The simplicity of the central NAF may account for its relatively simple behavior. If correct, the study of simple plate boundary faults may provide new insights into the constitutive elements of fault zones, and may aid in identifying those components that are critical for better forecasting future seismicity in complex systems.

Kinematics and timing of three superposed extensional systems, east central Idaho: Evidence for an Eocene tectonic transition

NASA Astrophysics Data System (ADS)

Janecke, Susanne U.

1992-12-01

Cenozoic crustal extension in east central Idaho began about 50 Ma and continues at present. Three distinct episodes characterize one of the longest intervals of Cenozoic extension yet documented in the North America Cordillera. Crosscutting relationships between NE striking normal faults and volcanic rocks, regional dike trends, and slickenline data indicate NW-SE extension during peak Eocene volcanism about 49-48 Ma (episode 1). NE striking normal faults, with at most a few kilometers of offset, formed in an intraarc setting during rapid NE subduction of oceanic plates under the Pacific Northwest. North to NNW striking and west dipping normal faults, with offsets up to 10-15 km, formed during a younger middle Eocene to Oligocene basin-forming event (episode 2). This newly documented episode was the most important extensional event in east central Idaho and began during the waning phases of Challis volcanism. WSW-ENE to SW-NE extension during episode 2 was nearly perpendicular to the extension direction during episode 1 and perpendicular to the grain of the Idaho-Montana fold and thrust belt. The flip in extension direction between episode 1 and episode 2 is tightly constrained by 40Ar/39Ar age determinations to have taken place at the end of Eocene Challis magmatism about 46-48 Ma. I infer that plate boundary forces controlled the geometry of normal faults and dikes during episode 1, whereas internal stresses within previously thickened crust drove major SW to WSW directed extension during episode 2. A drop in convergence rates between the North American and Farallon plates between 59 Ma and 42 Ma (Stock and Molnar, 1988) may coincide with the onset of gravitational spreading during episode 2 and may also explain the abrupt end of Eocene magmatism in the Pacific Northwest. Miocene and younger SW dipping Basin and Range faults (episode 3) extended the region in a NE-SW direction. Although faults formed during episode 2 and episode 3 are not parallel, slickenlines indicate only small changes in slip vector trends, suggesting little rotation of the extension direction in east central Idaho since 46 Ma.

Miocene to present-day shortening and intermontane basin formation in the Andean Puna Plateau, NW Argentina (24°30'S)

NASA Astrophysics Data System (ADS)

Strecker, M. R.; Bookhagen, B.; Alonso, R. N.; Pingel, H.; Freymark, J.

2015-12-01

With average elevations of about 3.7 km the Altiplano-Puna Plateau of the southern central Andes constitutes the world's second largest orogenic plateau. The plateau generally consists of internally drained, partly coalesced sedimentary basins bordered by reverse-fault bounded ranges, >5 km high. In the Puna, the Argentine sector of the plateau, active tectonism has been interpreted to be characterized by a low level of strike-slip and normal faulting associated with mafic volcanism. In contrast, the eastern plateau margins and the adjacent foreland record a higher level of seismicity and ongoing contraction. Despite ubiquitous Plio-Pleistocene normal faulting along the eastern plateau margins, our new observations record contraction in the plateau interior. Fanning of E-dipping Miocene sedimentary strata involved in the formation of an anticline in the Pocitos Basin of the central Puna interior indicates growth, which must have begun after 7 Ma; 1.5-m.y.-old lacustrine strata as well as tilted Pleistocene lacustrine shorelines associated with this structure indicate sustained uplift into the Quaternary. Corresponding observations along the eastern border of the Pocitos Basin show that <3.5-m.y.-old strata are involved in contractile deformation and basin compartmentalization. Shortening in the central Puna is compatible with Plio-Pleistocene shortening in the low-elevation Salar de Atacama farther west, and may indicate that low-elevation sectors of the plateau have not yet reached a critical elevation that is conducive to normal faulting as observed elsewhere. The onset of extensional deformation in the Puna is thus highly disparate in space and time. Coeval regional thrusting, strike-slip, and normal faulting do not support a structural and topographic setting that promotes wholesale extension and orogenic collapse of the plateau realm.

Rayleigh wave group velocity and shear wave velocity structure in the San Francisco Bay region from ambient noise tomography

NASA Astrophysics Data System (ADS)

Li, Peng; Thurber, Clifford

2018-06-01

We derive new Rayleigh wave group velocity models and a 3-D shear wave velocity model of the upper crust in the San Francisco Bay region using an adaptive grid ambient noise tomography algorithm and 6 months of continuous seismic data from 174 seismic stations from multiple networks. The resolution of the group velocity models is 0.1°-0.2° for short periods (˜3 s) and 0.3°-0.4° for long periods (˜10 s). The new shear wave velocity model of the upper crust reveals a number of important structures. We find distinct velocity contrasts at the Golden Gate segment of the San Andreas Fault, the West Napa Fault, central part of the Hayward Fault and southern part of the Calaveras Fault. Low shear wave velocities are mainly located in Tertiary and Quaternary basins, for instance, La Honda Basin, Livermore Valley and the western and eastern edges of Santa Clara Valley. Low shear wave velocities are also observed at the Sonoma volcanic field. Areas of high shear wave velocity include the Santa Lucia Range, the Gabilan Range and Ben Lomond Plutons, and the Diablo Range, where Franciscan Complex or Silinian rocks are exposed.

Bedrock geologic map of the Yucca Mountain area, Nye County, Nevada

USGS Publications Warehouse

Day, Warren C.; Dickerson, Robert P.; Potter, Christopher J.; Sweetkind, Donald S.; San Juan, Carma A.; Drake, Ronald M.; Fridrich, Christopher J.

1998-01-01

Yucca Mountain, Nye County, Nevada, has been identified as a potential site for underground storage of high-level radioactive nuclear waste. Detailed bedrock geologic maps form an integral part of the site characterization program by providing the fundamental framework for research into the geologic hazards and hydrologic behavior of the mountain. This bedrock geologic map provides the geologic framework and structural setting for the area in and adjacent to the site of the potential repository. The study area comprises the northern and central parts of Yucca Mountain, located on the southern flank of the Timber Mountain-Oasis Valley caldera complex, which was the source for many of the volcanic units in the area. The Timber Mountain-Oasis Valley caldera complex is part of the Miocene southwestern Nevada volcanic field, which is within the Walker Lane belt. This tectonic belt is a northwest-striking megastructure lying between the more active Inyo-Mono and Basin-and-Range subsections of the southwestern Great Basin.Excluding Quaternary surficial deposits, the map area is underlain by Miocene volcanic rocks, principally ash-flow tuffs with lesser amounts of lava flows. These volcanic units include the Crater Flat Group, the Calico Hills Formation, the Paintbrush Group, and the Timber Mountain Group, as well as minor basaltic dikes. The tuffs and lava flows are predominantly rhyolite with lesser amounts of latite and range in age from 13.4 to 11.6 Ma. The 10-Ma basaltic dikes intruded along a few fault traces in the north-central part of the study area. Fault types in the area can be classified as block bounding, relay structures, strike slip, and intrablock. The block-bounding faults separate the 1- to 4-km-wide, east-dipping structural blocks and exhibit hundreds of meters of displacement. The relay structures are northwest-striking normal fault zones that kinematically link the block-bounding faults. The strike-slip faults are steep, northwest-striking dextral faults located in the northern part of Yucca Mountain. The intrablock faults are modest faults of limited offset (tens of meters) and trace length (less than 7 km) that accommodated intrablock deformation.The concept of structural domains provides a useful tool in delineating and describing variations in structural style. Domains are defined across the study area on the basis of the relative amount of internal faulting, style of deformation, and stratal dips. In general, there is a systematic north to south increase in extensional deformation as recorded in the amount of offset along the block-bounding faults as well as an increase in the intrablock faulting.The rocks in the map area had a protracted history of Tertiary extension. Rocks of the Paintbrush Group cover much of the area and obscure evidence for older tectonism. An earlier history of Tertiary extension can be inferred, however, because the Timber Mountain-Oasis Valley caldera complex lies within and cuts an older north-trending rift (the Kawich-Greenwater rift}. Evidence for deformation during eruption of the Paintbrush Group is locally present as growth structures. Post-Paintbrush Group, pre-Timber Mountain Group extension occurred along the block-bounding faults. The basal contact of the 11.6-Ma Rainier Mesa Tuff of the Timber Mountain Group provides a key time horizon throughout the area. Other workers have shown that west of the study area in northern Crater Flat the basal angular unconformity is as much as 20° between the Rainier Mesa and underlying Paintbrush Group rocks. In the westernmost part of the study area the unconformity is smaller (less than 10°), whereas in the central and eastern parts of the map area the contact is essentially conformable. In the central part of the map the Rainier Mesa Tuff laps over fault splays within the Solitario Canyon fault zone. However, displacement did occur on the block-bounding faults after deposition of the Rainier Mesa Tuff inasmuch as it is locally caught up in the hanging-wall deformation of the block-bounding faults. Therefore, the regional Tertiary to Recent extension was protracted, occurring prior to and after the eruption of the tuffs exposed at Yucca Mountain.

Heat flow and energetics of the San Andreas fault zone.

USGS Publications Warehouse

Lachenbruch, A.H.; Sass, J.H.

1980-01-01

Approximately 100 heat flow measurements in the San Andreas fault zone indicate 1) there is no evidence for local frictional heating of the main fault trace at any latitude over a 1000-km length from Cape Mendocino to San Bernardino, 2) average heat flow is high (ca.2 HFU, ca.80 mW m-2) throughout the 550-km segment of the Coast Ranges that encloses the San Andreas fault zone in central California; this broad anomaly falls off rapidly toward the Great Valley to the east, and over a 200-km distance toward the Mendocino Triple Junction to the northwest. As others have pointed out, a local conductive heat flow anomaly would be detectable unless the frictional resistance allocated to heat production on the main trace were less than 100 bars. Frictional work allocated to surface energy of new fractures is probably unimportant, and hydrologic convection is not likely to invalidate the conduction assumption, since the heat discharge by thermal springs near the fault is negligible. -Authors

Origin of narrow terranes and adjacent major terranes occurring along the denali fault in the eastern and central alaska range, alaska

USGS Publications Warehouse

Nokleberg, W.J.; Richter, D.H.

2007-01-01

Several narrow terranes occur along the Denali fault in the Eastern and Central Alaska Range in Southern Alaska. These terranes are the Aurora Peak, Cottonwood Creek, Maclaren, Pingston, and Windy terranes, and a terrane of ultramafic and associated rocks. Exterior to the narrow terranes to the south is the majorWrangellia island arc composite terrane, and to the north is the major Yukon Tanana metamorphosed continental margin terrane. Overlying mainly the northern margin of the Wrangellia composite terrane are the Kahiltna overlap assemblage to the west, and the Gravina- Nutzotin-Gambier volcanic-plutonic- sedimentary belt to the east and southeast. The various narrow terranes are interpreted as the result of translation of fragments of larger terranes during two major tectonic events: (1) Late Jurassic to mid-Cretaceous accretion of the Wrangellia island arc composite terrane (or superterrane composed of the Wrangellia, Peninsular, and Alexander terranes) and associated subduction zone complexes; and (2) starting in about the Late Cretaceous, dextral transport of the Wrangellia composite terrane along the Denali fault. These two major tectonic events caused: (1) entrapment of a lens of oceanic lithosphere along the suture belt between the Wrangellia composite terrane and the North American Craton Margin and outboard accreted terranes to form the ultramafic and mafic part of the terrane of ultramafic and associated rocks, (2) subsequent dextral translation along the Denali fault of the terrane of ultramafic and associated rocks, (3) dextral translation along the Denali fault of the Aurora Peak, Cottonwood Creek, and Maclaren and continental margin arc terranes from part of the Coast plutonic-metamorphic complex (Coast-North Cascade plutonic belt) in the southwest Yukon Territory or Southeastern Alaska, (4) dextral translation along the Denali fault of the Pingston passive continental margin from a locus along the North American Continental Margin, and (5) formation and dextral transport along the Denali fault of the m??lange of the Windy terrane from fragments of the Gravina-Nutzotin-Gambier volcanic-plutonic-sedimentary belt and from the North American Continental Margin. Copyright ?? 2007 The Geological Society of America.

Fluid-driven normal faulting earthquake sequences in the Taiwan orogen

NASA Astrophysics Data System (ADS)

Wang, Ling-hua; Rau, Ruey-Juin; Lee, En-Jui

2017-04-01

Seismicity in the Central Range of Taiwan shows normal faulting mechanisms with T-axes directing NE, subparallel to the strike of the mountain belt. We analyze earthquake sequences occurred within 2012-2015 in the Nanshan area of northern Taiwan which indicating swarm behavior and migration characteristics. We select events larger than 2.0 from Central Weather Bureau catalog and use the double-difference relocation program hypoDD with waveform cross-correlation in the Nanshan area. We obtained a final count of 1406 (95%) relocated earthquakes. Moreover, we compute focal mechanisms using USGS program HASH by P-wave first motion and S/P ratio picking and 114 fault plane solutions with M 3.0-5.87 were determined. To test for fluid diffusion, we model seismicity using the equation of Shapiro et al. (1997) by fitting earthquake diffusing rate D during the migration period. According to the relocation result, seismicity in the Taiwan orogenic belt present mostly N25E orientation parallel to the mountain belt with the same direction of the tension axis. In addition, another seismic fracture depicted by seismicity rotated 35 degree counterclockwise to the NW direction. Nearly all focal mechanisms are normal fault type. In the Nanshan area, events show N10W distribution with a focal depth range from 5-12 km and illustrate fault plane dipping about 45-60 degree to SW. Three months before the M 5.87 mainshock which occurred in March, 2013, there were some foreshock events occurred in the shallow part of the fault plane of the mainshock. Half a year following the mainshock, earthquakes migrated to the north and south, respectively with processes matched the diffusion model at a rate of 0.2-0.6 m2/s. This migration pattern and diffusion rate offer an evidence of 'fluid-driven' process in the fault zone. We also find the upward migration of earthquakes in the mainshock source region. These phenomena are likely caused by the opening of the permeable conduit due to the M 5.87 earthquake and the rise of the high pressure fluid.

Modeling the Proterozoic Basement's Effective Stress Field, Assessing Fault Reactivation Potential Related to Increased Fluid Pressures, and Improved 3D Structural Interpretation of Faulting within Wellington and Anson-Bates Fields, Sumner County, Kansas

NASA Astrophysics Data System (ADS)

Keast, R. T.; Lacroix, B.; Raef, A. E.; Adam, C.; Bidgoli, T. S.; Leclere, H.; Daniel, G.

2017-12-01

South-central Kansas has experienced an increase in seismic activity within the Proterozoic basement. Since 2013, United States Geological Survey (USGS) seismograph stations have recorded 3414 earthquakes. Fluid pressure increases associated with recent high-rate wastewater injection into the dolomitic Arbuckle disposal zone is the hypothesized cause of reactivation of the faulted study region's Proterozoic basement. Although the magnitude of the pressure change required for reactivation of these faults is likely low given failure equilibrium conditions in the midcontinent, heterogeneities in the basement could allow for a range of fluid pressure changes associated with injection. This research aims to quantify the fluid pressure changes responsible for fault reactivation of the Proterozoic basement. To address this issue, we use 103 focal mechanisms and 3,414 seismic events, from the USGS catalog, within an area encompassing 4,000 km2. Three major fault populations have been identified using the dense seismicity and focal mechanism datasets. Win-Tensor paleostress reconstruction software was used to identify effective stress ratios, R = (σ'1/σ'3), and stress tensors for twelve 22 km by 17 km grid squares covering the study area. One fault population strikes parallel with the Nemaha Ridge basement structure ( 030˚). Another reoccurring fault population is oriented 310˚, closely parallel to the Central Kansas Uplift, a subtle anticlinal structure subjected to repeated movement during the Paleozoic. The third population of faults is parallel to the regional maximum compressive stress oriented 265˚ as determined by previous researchers using borehole image logs and shear wave anisotropy. A 3D stress modeling Matlab script was used to analyze fault reactivation potential based on results obtained from Win-Tensor to better understand fault orientations and their susceptibility to reactivation related to pore fluid pressure increases. In addition, the orientations of these normal and strike-slip fault populations suggest the development of a transtensional basin, not yet identified.

Plate rotations, fault slip rates, fault locking, and distributed deformation in northern Central America from 1999-2017 GPS observations

NASA Astrophysics Data System (ADS)

Ellis, A. P.; DeMets, C.; Briole, P.; Cosenza, B.; Flores, O.; Guzman-Speziale, M.; Hernandez, D.; Kostoglodov, V.; La Femina, P. C.; Lord, N. E.; Lasserre, C.; Lyon-Caen, H.; McCaffrey, R.; Molina, E.; Rodriguez, M.; Staller, A.; Rogers, R.

2017-12-01

We describe plate rotations, fault slip rates, and fault locking estimated from a new 100-station GPS velocity field at the western end of the Caribbean plate, where the Motagua-Polochic fault zone, Middle America trench, and Central America volcanic arc faults converge. In northern Central America, fifty-one upper-plate earthquakes caused approximately 40,000 fatalities since 1900. The proximity of main population centers to these destructive earthquakes and the resulting loss of human life provide strong motivation for studying the present-day tectonics of Central America. Plate rotations, fault slip rates, and deformation are quantified via a two-stage inversion of daily GPS position time series using TDEFNODE modeling software. In the first stage, transient deformation associated with three M>7 earthquakes in 2009 and 2012 is estimated and removed from the GPS position time series. In Stage 2, linear velocities determined from the corrected GPS time series are inverted to estimate deformation within the western Caribbean plate, slip rates along the Motagua-Polochic faults and faults in the Central America volcanic arc, and the gradient of extension in the Honduras-Guatemala wedge. Major outcomes of the second inversion include the following: (1) Confirmation that slip rates on the Motagua fault decrease from 17-18 mm/yr at its eastern end to 0-5 mm/yr at its western end, in accord with previous results. (2) A transition from moderate subduction zone locking offshore from southern Mexico and parts of southern Guatemala to weak or zero coupling offshore from El Salvador and parts of Nicaragua along the Middle America trench. (3) Evidence for significant east-west extension in southern Guatemala between the Motagua fault and volcanic arc. Our study also shows evidence for creep on the eastern Motagua fault that diminishes westward along the North America-Caribbean plate boundary.

The Tonalá fault in southeastern Mexico: Evidence that the Central America forearc sliver is not being detached?

NASA Astrophysics Data System (ADS)

Guzman-Speziale, M.; Molina-Garza, R. S.

2012-12-01

The Tonalá fault is a NW-SE oriented feature that flanks the Chiapas Massif on its southwestern side. Several authors coincide that the fault originally developed as a right-lateral structure in the Jurassic, but was reactivated as a left-lateral fault in the Miocene. Seismicity along the fault is low: Only one earthquake with magnitude 5.0 or larger is reported along the Tonalá fault in the years 1964 to present. Fault-plane solutions determined by the Mexican Seismological Survey for earthquakes along the fault show left-lateral, strike-slip faulting. The Tonalá fault lies on the northwestern continuation of the Central America volcanic arc. The volcanic arc is the site of medium-sized (magnitudes up to 6.5) shallow, right-lateral, strike-slip earthquakes. This has led several workers to propose that the forearc sliver is being detached from the Caribbean plate along the arc, moving northward. GPS studies have confirmed relative motion between the Chortis block and the forearc sliver. Recent and current motion along the Tonalá fault is in contradiction with motion and detachment of the forearc sliver along the Central America volcanic arc. Left-lateral motion along it cannot accomodate northwest displacement of the forearc sliver. Motion of the Central America forearc would require NW directed compression between the continental shelf of Chiapas and the forearc itself, which is not observed. Therefore, either another fault (or faults) accomodates right-lateral motion and detachment of the forearc sliver, or the sliver is not being detached and relative motion between the forearc sliver and the Chortis block corresponds to displacement of the latter. We suggest that, as proposed by previous authors, the Tonalá fault is instead part of a fault system that runs from the state of Oaxaca (the Valle Nacional fault), forming an arc concave to the northeast, and running perpendicular to the maximum slope of subduction in the area.

Modeling River Incision Across Active Normal Faults Using the Channel-Hillslope Integrated Landscape Development Model (CHILD): the case of the Central Apennines (Italy)

NASA Astrophysics Data System (ADS)

Attal, M.; Tucker, G.; Whittaker, A.; Cowie, P.; Roberts, G.

2005-12-01

River systems constitute some of the most efficient agents that shape terrestrial landscapes. Fluvial incision rates govern landscape evolution but, due to the variety of processed involved and the difficulty of quantifying them in the field, there is no "universal theory" describing the way rivers incise into bedrock. The last decades have seen the birth of numerous fluvial incision laws associated with models that assign different roles to hydrodynamic variables and to sediments. In order to discriminate between models and constrain their parameters, the transient response of natural river systems to a disturbance (tectonic or climatic) can be used. Indeed, the different models predict different kinds of transient response whereas most models predict a similar power law relationship between slope and drainage area at equilibrium. To this end, a coupled field - modeling study is in progress. The field area consists of the Central Apennines that are subject to active faulting associated with a regional extensional regime. Fault initiation occurred 3 My ago, associated with throw rates of 0.3 +/- 0.2 mm/yr. Due to fault interaction and linkage, the throw rate on the faults located near the center of the fault system increased dramatically 0.7 My ago (up to 2 mm/yr), whereas slip rates on distal faults either decayed or remained approximately constant. The present study uses the landscape evolution model, CHILD, to examine the behavior of rivers draining across these active faults. Distal and central faults are considered in order to track the effects of the fault acceleration on the development of the fluvial network. River characteristics have been measured in the field (e.g. channel width, slope, sediment grain size) and extracted from a 20m DEM (e.g. channel profile, drainage area). We use CHILD to test the ability of alternative incision laws to reproduce observed topography under known tectonic forcing. For each of the fluvial incision models, a Monte-Carlo simulation has been performed, allowing the exploration of a wide range of values for the different parameters relative to tectonic, climate, sediment characteristics, and channel geometry. Observed profiles are consistent with a dominantly wave-like, as opposed to diffusive, transient response to accelerated fault motion. The ability of the different models to reproduce more or less accurately the catchment characteristics, in particular the specific profiles exhibited by the rivers, are discussed in light of our first results.

Millennial strain partitioning revealed by 36Cl cosmogenic data on active bedrock fault scarps from Abruzzo, Italy

NASA Astrophysics Data System (ADS)

Gregory, Laura; Roberts, Gerald; Cowie, Patience; Wedmore, Luke; McCaffrey, Ken; Shanks, Richard; Zijerveld, Leo; Phillips, Richard

2017-04-01

In zones of distributed continental faulting, it is critical to understand how slip is partitioned onto brittle structures over both long-term millennial time scales and shorter-term individual earthquake cycles. Measuring earthquake slip histories on different timescales is challenging due to earthquake repeat-times being longer or similar to historical earthquake records, and a paucity of data on fault activity covering millennial to Quaternary scales in detail. Cosmogenic isotope analyses from bedrock fault scarps have the potential to bridge the gap, as these datasets track the exposure of fault planes due to earthquakes with millennial resolution. In this presentation, we present new 36Cl data combined with historical earthquake records to document orogen-wide changes in the distribution of seismicity on millennial timescales in Abruzzo, central Italy. Seismic activity due to extensional faulting was concentrated on the northwest side of the mountain range during the historical period, or since approximately the 14th century. Seismicity is more limited on the southwest side of Abruzzo during historical times. This pattern has led some to suggest that faults on the southwest side of Abruzzo are not active, however clear fault scarps cutting Holocene-aged slopes are well preserved across the whole of the orogen. These scarps preserve an excellent record of Late Pleistocene to Holocene earthquake activity, which can be quantified using cosmogenic isotopes that track the exposure of the bedrock fault scarps. 36Cl accumulates in the fault scarps as the plane is progressively exhumed by earthquakes and the concentration of 36Cl measured up the fault plane reflects the rate and patterns of slip. We utilise Bayesian modelling techniques to estimate slip histories based on the cosmogenic data. Each sampling site is carefully characterised using LiDAR and GPR to ensure that fault plane exposure is due to slip during earthquakes and not sediment transport processes. In this presentation we will focus on new data from faults located across-strike in Abruzzo. Many faults in Abruzzo demonstrate slip rate variability on millennial timescales, with relatively fast slip interspersed between quiescent periods. We show that heightened activity is co-located and spatially migrates across Abruzzo over time. We highlight the importance of understanding this dynamic fault behaviour of migrating seismic activity, and in particular how our research is relevant to the 2016 Amatrice-Vettore seismic sequence in central Italy.

New paleomagnetic results from Cretaceous rocks of the Gyaring Co fault region, central Tibet

NASA Astrophysics Data System (ADS)

Finn, D.; Zhao, X.; Lippert, P. C.; Yin, A.; Li, Y.; Wang, C.; Meng, J.; Zhang, S.; Li, H.

2010-12-01

Conjugate strike-slip faults are widespread features throughout the Alpine-Himalayan collision zone. They often exhibit V-shapes in map view and trend 60-75° from the maximum compressive-stress (σ1). Andersonian fault mechanics, however, predict faults to form X-shaped at ~30° from σ1. Consequently, V-shaped conjugate faults have been thought to initiate at ~30° to σ1, and subsequently rotate into their current orientation through continued shortening. Alternatively, the Paired General Shear Zone (PGSZ) model may explain development of conjugate strike-slip faults in their modern orientations, predicting no rotation. Strike-slip faulting produces rigid-body motion and internal deformation quantifiable by paleomagnetism when integrated with structural information. We wonder if paleomagnetic studies of the fault-bounded blocks in central Tibet would allow us to differentiate the two competing models for the formation of V-shaped conjugate faults. We collected over 300 paleomagnetic samples (40 sites) from stratigraphic sections in Shengza and Nima areas of central Tibet. The rocks we collected range from Jurassic to Oligocene, and are mainly grey limestones and red sediments including siltstone, mudstone, sandstone, and conglomerate, offering opportunity of applying paleomagnetic fold and conglomerate tests to check the stability of the remanent magnetization. Up to present, useful results were obtained for 150 of the early Cretaceous limestone and sandstone samples (Langshan and Duoni formations, respectively). We have characterized the stable components of natural remanent magnetization (NRM) of these samples through detailed thermal (mainly) and alternating field (AF) demagnetization. We have also conducted rock magnetic investigation to identify the magnetic carriers in these rocks. Most limestone and red sandstones exhibit two distinctive components of magnetization. The lower unblocking-temperature component is an overprint. The higher unblocking-temperature component is the characteristic component (ChRM), is well defined in vector demagnetization plots with both normal and reversed polarities and carried by magnetite and hematite. The site-mean directions pass the local fold test at more than 95% confidence level. Our new results indicate that there has been no rotation of this region relative to Eurasia, Mongolia, and the North and South China blocks since the lower Cretaceous. Thus paleomagnetic evidence appears to favor the PGSZ model and supports geological estimates for the shortening north of the Bangong suture zone, leading to an improved tectonic interpretation of the region.

Faults and volcanoes: Main volcanic structures in the Acambay Graben, Mexico

NASA Astrophysics Data System (ADS)

Aguirre-Diaz, G. J.; Pedrazzi, D.; Suñe-Puchol, I.; Lacan, P.

2016-12-01

The Mexican Volcanic Belt (MVB) province is best known by the major stratovolcanoes, such as Popocatepetl and Colima, but most of the province is formed by modest size stratovolcanoes and monogenetic cones. Regional fault systems were developed together with the building of the volcanic province; the most notorious one is Chapala-Tula Fault System (CTFS), which runs parallel to the central sector of the MVB, and thus it is also referred to as the Intra-Arc fault system. Acambay graben (AG) is part of this central system. It is a 20 x 70 km depression located 100 km to the NW of Mexico City, at the easternmost end of the E-W trending CTFS, and was formed as the result of NS to NE oriented extension. Seismically active normal faults, such as the Acambay-Tixmadejé fault, with a mB =7 earthquake in 1912, delimit the AG. The graben includes several volcanic structures and associated deposits ranging in age from Miocene to 3 ka. The main structures are two stratovolcanoes, Altamirano (900 m high) and Temascalcingo (800 m high). There are also several Miocene-Pliocene lava domes, and Quaternary small cinder cones and shield volcanoes. Faulting of the Acambay graben affects all these volcanic forms, but depending on their ages, the volcanoes are cut by several faults or by a few. That is the case of Altamirano and Temascalcingo volcanoes, where the former is almost unaffected whereas the latter is highly dissected by faults. Altamirano is younger than Temascalcingo; youngest pyroclastic deposits from Altamirano are dated at 12-3 ka, and those from Temascalcingo at 40-25 ka (radiocarbon ages). The relatively young ages found in volcanic deposits within the Acambay graben raise the volcanic danger level in this area, originally marked as an inactive volcanic zone, but activity could restart at any time. Supported by DGAPA-PAPIIT-UNAM grant IN-104615.

Non-tectonic exposure Rates along Bedrock Fault Scarps in an active Mountain Belt of the central Apennines

NASA Astrophysics Data System (ADS)

Kastelic, Vanja; Burrato, Pierfrancesco; Carafa, Michele M. C.; Basili, Roberto

2017-04-01

The central Apennines (Italy) are a mountain chain affected by post-collisional active extension along NW-SE striking normal faults and well-documented regional-scale uplift. Moderate to strong earthquakes along the seismogenically active extensional faults are frequent in this area, thus a good knowledge on the characteristics of the hosting faults is necessary for realistic seismic hazard models. The studied bedrock fault surfaces are generally located at various heights on mountain fronts above the local base level of glacio-fluvial valleys and intermountain fluvio-lacustrine basins and are laterally confined to the extent of related mountain fronts. In order to investigate the exposure of the bedrock fault scarps from under their slope-deposit cover, a process that has often been exclusively attributed to co-seismic earthquake slip and used as proxy for tectonic slip rates and earthquake recurrence estimations, we have set up a measurement experiment along various such structures. In this experiment we measure the relative position of chosen markers on the bedrock surface and the material found directly at the contact with its hanging wall. We present the results of monitoring the contact between the exposed fault surfaces and slope deposits at 23 measurement points on 12 different faults over 3.4 year-long observation period. We detected either downward or upward movements of the slope deposit with respect to the fault surface between consecutive measurements. During the entire observation period all points, except one, registered a net downward movement in the 2.9 - 25.6 mm/yr range, resulting in the progressive exposure of the fault surface. During the monitoring period no major earthquakes occurred in the region, demonstrating the measured exposure process is disconnected from seismic activity. We do however observe a positive correlation between the higher exposure in respect to higher average temperatures. Our results indicate that the fault surface exposure rates are rather due to gravitational and landsliding movements aided by weathering and slope degradation processes. The so far neglected slope degradation and other (sub)surface processes should thus be carefully taken into consideration before attempting to recover fault slip rates using surface gathered data. The results of the present studies have been recently published (Kastelic et al., 2016) and our research is ongoing, implementing the so-far results with newer measurements and other techniques in order to improve our knowledge on the magnitude of the exposure and its causative process(es). Kastelic, V., P. Burrato, M. M. C. Carafa, and R. Basili (2016), Repeated surveys reveal nontectonic exposure of supposedly active normal faults in the central Apennines, Italy, J. Geophys. Res. Earth Surf., 121, doi:10.1002/2016JF003953.

Correlation of clayey gouge in a surface exposure of serpentinite in the San Andreas Fault with gouge from the San Andreas Fault Observatory at Depth (SAFOD)

NASA Astrophysics Data System (ADS)

Moore, Diane E.; Rymer, Michael J.

2012-05-01

Magnesium-rich clayey gouge similar to that comprising the two actively creeping strands of the San Andreas Fault in drill core from the San Andreas Fault Observatory at Depth (SAFOD) has been identified in a nearby outcrop of serpentinite within the fault zone at Nelson Creek. Each occurrence of the gouge consists of porphyroclasts of serpentinite and sedimentary rocks dispersed in a fine-grained, foliated matrix of Mg-rich smectitic clays. The clay minerals in all three gouges are interpreted to be the product of fluid-assisted, shear-enhanced reactions between quartzofeldspathic wall rocks and serpentinite that was tectonically entrained in the fault from a source in the Coast Range Ophiolite. We infer that the gouge at Nelson Creek connects to one or both of the gouge zones in the SAFOD core, and that similar gouge may occur at depths in between. The special significance of the outcrop is that it preserves the early stages of mineral reactions that are greatly advanced at depth, and it confirms the involvement of serpentinite and the Mg-rich phyllosilicate minerals that replace it in promoting creep along the central San Andreas Fault.

A New Perspective on Fault Geometry and Slip Distribution of the 2009 Dachaidan Mw 6.3 Earthquake from InSAR Observations

PubMed Central

Liu, Yang; Xu, Caijun; Wen, Yangmao; Fok, Hok Sum

2015-01-01

On 28 August 2009, the northern margin of the Qaidam basin in the Tibet Plateau was ruptured by an Mw 6.3 earthquake. This study utilizes the Envisat ASAR images from descending Track 319 and ascending Track 455 for capturing the coseismic deformation resulting from this event, indicating that the earthquake fault rupture does not reach to the earth’s surface. We then propose a four-segmented fault model to investigate the coseismic deformation by determining the fault parameters, followed by inverting slip distribution. The preferred fault model shows that the rupture depths for all four fault planes mainly range from 2.0 km to 7.5 km, comparatively shallower than previous results up to ~13 km, and that the slip distribution on the fault plane is complex, exhibiting three slip peaks with a maximum of 2.44 m at a depth between 4.1 km and 4.9 km. The inverted geodetic moment is 3.85 × 1018 Nm (Mw 6.36). The 2009 event may rupture from the northwest to the southeast unilaterally, reaching the maximum at the central segment. PMID:26184210

A New Perspective on Fault Geometry and Slip Distribution of the 2009 Dachaidan Mw 6.3 Earthquake from InSAR Observations.

PubMed

Liu, Yang; Xu, Caijun; Wen, Yangmao; Fok, Hok Sum

2015-07-10

On 28 August 2009, the northern margin of the Qaidam basin in the Tibet Plateau was ruptured by an Mw 6.3 earthquake. This study utilizes the Envisat ASAR images from descending Track 319 and ascending Track 455 for capturing the coseismic deformation resulting from this event, indicating that the earthquake fault rupture does not reach to the earth's surface. We then propose a four-segmented fault model to investigate the coseismic deformation by determining the fault parameters, followed by inverting slip distribution. The preferred fault model shows that the rupture depths for all four fault planes mainly range from 2.0 km to 7.5 km, comparatively shallower than previous results up to ~13 km, and that the slip distribution on the fault plane is complex, exhibiting three slip peaks with a maximum of 2.44 m at a depth between 4.1 km and 4.9 km. The inverted geodetic moment is 3.85 × 10(18) Nm (Mw 6.36). The 2009 event may rupture from the northwest to the southeast unilaterally, reaching the maximum at the central segment.

Complex Paleotopography and Faulting near the Elsinore Fault, Coyote Mountains, southern California

NASA Astrophysics Data System (ADS)

Brenneman, M. J.; Bykerk-Kauffman, A.

2012-12-01

The Coyote Mountains of southern California are bounded on the southwest by the Elsinore Fault, an active dextral fault within the San Andreas Fault zone. According to Axen and Fletcher (1998) and Dorsey and others (2011), rocks exposed in these mountains comprise a portion of the hanging wall of the east-vergent Salton Detachment Fault, which was active from the late Miocene-early Pliocene to Ca. 1.1-1.3 Ma. Detachment faulting was accompanied by subsidence, resulting in deposition of a thick sequence of marine and nonmarine sedimentary rocks. Regional detachment faulting and subsidence ceased with the inception of the Elsinore Fault, which has induced uplift of the Coyote Mountains. Detailed geologic mapping in the central Coyote Mountains supports the above interpretation and adds some intriguing details. New discoveries include a buttress unconformity at the base of the Miocene/Pliocene section that locally cuts across strata at an angle so high that it could be misinterpreted as a fault. We thus conclude that the syn-extension strata were deposited on a surface with very rugged topography. We also discovered that locally-derived nonmarine gravel deposits exposed near the crest of the range, previously interpreted as part of the Miocene Split Mountain Group by Winker and Kidwell (1996), unconformably overlie units of the marine Miocene/Pliocene Imperial Group and must therefore be Pliocene or younger. The presence of such young gravel deposits on the crest of the range provides evidence for its rapid uplift. Additional new discoveries flesh out details of the structural history of the range. We mapped just two normal faults, both of which were relatively minor, thus supporting Axen and Fletcher's assertion that the hanging wall block of the Salton Detachment Fault had not undergone significant internal deformation during extension. We found abundant complex synthetic and antithetic strike-slip faults throughout the area, some of which offset Quaternary alluvial deposits. We interpret these faults as Riedel shears of the Elsinore Fault that distribute dextral strain over an area at least 2 km wide. Finally, our mapping of the Elsinore Fault itself reveals two releasing bends that are superimposed on the overall transpressive regime in the area. Axen, G.J. and Fletcher, J.M., 1998, Hall Volume, GSA, p. 365-392. Dorsey, R.J., Housen, B.A., Janecke, S.U., Fanning, C. M., Spears, A.L.F., 2011, GSA Bulletin, v. 123, p. 771-793. Winker, C.D. and Kidwell, S.M., 1996, Field Conference Guide, Pacific Section AAPG/SEPM, Book 80, p. 295-336.

Quaternary shortening in the central Puna Plateau of NW Argentina: Preliminary results from the Salar de Pocitos, Salta province (24.5° S, 67° W)

NASA Astrophysics Data System (ADS)

Freymark, Jessica; Strecker, Manfred R.; Bookhagen, Bodo; Bekeschus, Benjamin; Eckelmann, Felix; Alonso, Ricardo

2013-04-01

Active tectonism in Cenozoic orogenic plateaus is often characterized by a combination of active extensional and strike-slip faulting subsequent to protracted phases of shortening and the build-up of high topography. In the Puna Plateau of NW Argentina, the southern part of the world's second largest orogenic plateau, the changeover from shortening to extensional tectonics is thought to have occured between 7 and 5 Ma along the southeastern plateau margin, while the central and northern plateau areas apparently changed into an extensional regime between 9 and 6 Ma (Cladouhos et al., 1994). Despite these observations of extensional structures we report on new data from the Salar de Pocitos that show sustained shortening in the south-central part of the plateau. The south-central Puna Plateau is characterized by an average elevation of about 3700 m with low relief and internally drained basins, which are bordered by reverse-fault bounded ranges. The N-S oriented Salar de Pocitos is an integral part of these contractional structures and covers an area of ~435 km². The western border of the basin constitutes the eastern flank of an anticline involving Tertiary and Quaternary sediments, while the eastern border is delimited by a N-S striking reverse fault, bounding the range front of the Sierra Qda. Honda. In the north of the Salar de Pocitos the three Miocene volcanoes Tultul, Delmedio and Pocitos form a barrier with the Salar del Rincón, and the south of the basin is bordered by fault blocks involving Ordovician lithologies that have left only a narrow valley that may have provided an outlet of the basin in the past. Multiple terraces generated during Late Pleistocene and Holocene lake highstands straddle the Pocitos Basin and serve as excellent strain markers to assess neotectonic deformation. We surveyed the terraces along N-S and E-W transects using a differential GPS. The E-W surveys are perpendicular to the structures that bound the basin and record differential basin-wide deformation. Although it is not possible yet to develop a reliable terrace chronology, taken together, the western terraces are higher than possibly equivalent terraces in the east, suggesting ongoing tilting related to protracted folding of the anticline in the west. In addition, orientations of faults, joints and tilted deposits were measured and analyzed. We show (preliminary) results and interpretations of these measurements. Tilted volcanic ash and sediment deposits have different dips and it appears that a distinct deformation stage is related to the regional anticline west of the Salar. A tectonic joint system and various small reverse faults also indicate active shortening in the area of the Salar de Pocitos from the Tertiary to the present-day. Reference: Cladouhos, T.T.; Allmendinger, R.W.; Coira, B. and Farrar, E. (1994): Late Cenozoic deformation in the Central Andes: fault kinematics from the northern Puna, northwestern Argentina and southwestern Bolivia (Journal of South American Earth Sciences, Vol. 7, No. 2., pp. 209-228)

New constraints on slip rates and locking depths of the San Andreas Fault System from Sentinel-1A InSAR and GAGE GPS observations

NASA Astrophysics Data System (ADS)

Ward, L. A.; Smith-Konter, B. R.; Higa, J. T.; Xu, X.; Tong, X.; Sandwell, D. T.

2017-12-01

After over a decade of operation, the EarthScope (GAGE) Facility has now accumulated a wealth of GPS and InSAR data, that when successfully integrated, make it possible to image the entire San Andreas Fault System (SAFS) with unprecedented spatial coverage and resolution. Resulting surface velocity and deformation time series products provide critical boundary conditions needed for improving our understanding of how faults are loaded across a broad range of temporal and spatial scales. Moreover, our understanding of how earthquake cycle deformation is influenced by fault zone strength and crust/mantle rheology is still developing. To further study these processes, we construct a new 4D earthquake cycle model of the SAFS representing the time-dependent 3D velocity field associated with interseismic strain accumulation, co-seismic slip, and postseismic viscoelastic relaxation. This high-resolution California statewide model, spanning the Cerro Prieto fault to the south to the Maacama fault to the north, is constructed on a 500 m spaced grid and comprises variable slip and locking depths along 42 major fault segments. Secular deep slip is prescribed from the base of the locked zone to the base of the elastic plate while episodic shallow slip is prescribed from the historical earthquake record and geologic recurrence intervals. Locking depths and slip rates for all 42 fault segments are constrained by the newest GAGE Facility geodetic observations; 3169 horizontal GPS velocity measurements, combined with over 53,000 line-of-sight (LOS) InSAR velocity observations from Sentinel-1A, are used in a weighted least-squares inversion. To assess slip rate and locking depth sensitivity of a heterogeneous rheology model, we also implement variations in crustal rigidity throughout the plate boundary, assuming a coarse representation of shear modulus variability ranging from 20-40 GPa throughout the (low rigidity) Salton Trough and Basin and Range and the (high rigidity) Central Valley and ocean lithosphere.

Temporal evolution of fault systems in the Upper Jurassic of the Central German Molasse Basin: case study Unterhaching

NASA Astrophysics Data System (ADS)

Budach, Ingmar; Moeck, Inga; Lüschen, Ewald; Wolfgramm, Markus

2018-03-01

The structural evolution of faults in foreland basins is linked to a complex basin history ranging from extension to contraction and inversion tectonics. Faults in the Upper Jurassic of the German Molasse Basin, a Cenozoic Alpine foreland basin, play a significant role for geothermal exploration and are therefore imaged, interpreted and studied by 3D seismic reflection data. Beyond this applied aspect, the analysis of these seismic data help to better understand the temporal evolution of faults and respective stress fields. In 2009, a 27 km2 3D seismic reflection survey was conducted around the Unterhaching Gt 2 well, south of Munich. The main focus of this study is an in-depth analysis of a prominent v-shaped fault block structure located at the center of the 3D seismic survey. Two methods were used to study the periodic fault activity and its relative age of the detected faults: (1) horizon flattening and (2) analysis of incremental fault throws. Slip and dilation tendency analyses were conducted afterwards to determine the stresses resolved on the faults in the current stress field. Two possible kinematic models explain the structural evolution: One model assumes a left-lateral strike slip fault in a transpressional regime resulting in a positive flower structure. The other model incorporates crossing conjugate normal faults within a transtensional regime. The interpreted successive fault formation prefers the latter model. The episodic fault activity may enhance fault zone permeability hence reservoir productivity implying that the analysis of periodically active faults represents an important part in successfully targeting geothermal wells.

Tectonic Evolution of the Çayirhan Neogene Basin (Ankara), Central Turkey

NASA Astrophysics Data System (ADS)

Behzad, Bezhan; Koral, Hayrettin; İşb&idot; l, Duygu; Karaaǧa; ç, Serdal

2016-04-01

Çayırhan (Ankara) is located at crossroads of the Western Anatolian extensional region, analogous to the Basin and Range Province, and suture zone of the Neotethys-Ocean, which is locus of the North Anatolian Transform since the Late Miocene. To the north of Çayırhan (Ankara), a Neogene sedimentary basin comprises Lower-Middle Miocene and Upper Miocene age formations, characterized by swamp, fluvial and lacustrine settings respectively. This sequence is folded and transected by neotectonic faults. The Sekli thrust fault is older than the Lower-Middle Miocene age formations. The Davutoǧlan fault is younger than the Lower-Middle Miocene formations and is contemporaneous to the Upper Miocene formation. The Çatalkaya fault is younger than the Upper Miocene formation. The sedimentary and tectonic features provide information on mode, timing and evolution of this Neogene age sedimentary basin in Central Turkey. It is concluded that the region underwent a period of uplift and erosion under the influence of contractional tectonics prior to the Early-Middle Miocene, before becoming a semi-closed basin under influence of transtensional tectonics during the Early-Middle Miocene and under influence of predominantly extensional tectonics during the post-Late Miocene times. Keywords: Tectonics, Extension, Transtension, Stratigraphy, Neotectonic features.

Recent deformation along the offshore Malibu Coast, Dume, and related faults west of Point Dume, southern California

USGS Publications Warehouse

Fisher, M.A.; Langenheim, V.E.; Sorlien, C.C.; Dartnell, P.; Sliter, R.W.; Cochrane, G.R.; Wong, F.L.

2005-01-01

Offshore faults west of Point Dume, southern California, are part of an important regional fault system that extends for about 206 km, from near the city of Los Angeles westward along the south flank of the Santa Monica Mountains and through the northern Channel Islands. This boundary fault system separates the western Transverse Ranges, on the north, from the California Continental Borderland, on the south. Previous research showed that the fault system includes many active fault strands; consequently, the entire system is considered a serious potential earthquake hazard to nearby Los Angeles. We present an integrated analysis of multichannel seismic- and high-resolution seismic-reflection data and multibeam-bathymetric information to focus on the central part of the fault system that lies west of Point Dume. We show that some of the main offshore faults have cumulative displacements of 3-5 km, and many faults are currently active because they deform the seafloor or very shallow sediment layers. The main offshore fault is the Dume fault, a large north-dipping reverse fault. In the eastern part of the study area, this fault offsets the seafloor, showing Holocene displacement. Onshore, the Malibu Coast fault dips steeply north, is active, and shows left-oblique slip. The probable offshore extension of this fault is a large fault that dips steeply in its upper part but flattens at depth. High-resolution seismic data show that this fault deforms shallow sediment making up the Hueneme fan complex, indicating Holocene activity. A structure near Sycamore knoll strikes transversely to the main faults and could be important to the analysis of the regional earthquake hazard because the structure might form a boundary between earthquake-rupture segments.

Reconnaissance geology of the Central Mastuj Valley, Chitral State, Pakistan

USGS Publications Warehouse

Stauffer, Karl W.

1975-01-01

The Mastuj Valley in Chitral State is a part of the Hindu Kush Range, and is one of the structurally most complicated areas in northern Pakistan. Sedimentary rocks ranging from at least Middle Devonian to Cretaceous, and perhaps Early Tertiary age lie between ridge-forming granodiorite intrusions and are cut by thrust faults. The thrust planes dip 10? to 40? to the north- west. Movement of the upper thrust plates has been toward the southeast relative to the lower blocks. If this area is structurally typical of the Hindu-Kush and Karakoram Ranges, then these mountains are much more tectonically disturbed than previously recorded, and suggest compression on a scale compatible with the hypothesis that the Himalayan, Karakoram, and Hindu Kush Ranges form part of a continental collision zone. The thrust faults outline two plates consisting of distinctive sedimentary rocks. The lower thrust plate is about 3,000 feet thick and consists of the isoclinally folded Upper Cretaceous to perhaps lower Tertiary Reshun Formation. It has overridden the Paleozoic metasedimentary rocks of the Chitral Slate unit. This thrust plate is, in turn, overridden by an 8,000-foot thick sequence consisting largely of Devonian to Carboniferous limestones and quartzites. A key factor in the tectonic processes has been the relatively soft and plastic lithology of the siltstone layers in the Reshun Formation which have acted as lubricants along the principal thrust faults, where they are commonly found today as fault slices and smears. The stratigraphic sequence, in the central Mastuj Valley was tentatively divided into 9 mapped units. The fossiliferous shales and carbonates of the recently defined Shogram Formation and the clastlcs of the Reshun Formation have been fitted into a sequence of sedimentary rocks that has a total thick- ness of at least 13,000 feet and ranges in age from Devonian to Neogene. Minerals of potential economic significance include antimony sulfides which have been mined elsewhere in Chitral, the tungstate, scheelite, which occurs in relatively high concentrations in heavy-mineral fractions of stream sands, and an iron-rich lateritic rock.

Post-Neogene tectonism along the Aravalli Range, Rajasthan, India

NASA Astrophysics Data System (ADS)

Sen, Deepawati; Sen, Saurindranath

1983-03-01

The Aravalli Range runs southwest from Delhi for a distance of about 700 km. Its western margin is well defined, but the eastern margin is diffuse. Five geomorphic provinces are recognized in the study area: the western piedmont plains; the ridge and valley province which in the Central Aravallis occurs at two different heights separated by a fault scarp; the plateau province demarcated from the former by a fault scarp, confined to the Southern Aravallis, and occurring for a short stretch at two heights across another fault scarp; the BGC rolling plains east of the Range; and the BGC uplands south of the above. The scarps coincide with Precambrian faults. A series of rapids and water-falls, together with deeply entrenched river courses across the scarps and the youthful aspects of the escarpments with no projecting spurs, or straight river courses along their feet, all point unmistakably to a recent or post-Neogene vertical uplift along pre-existing faults. Presence of knickpoints at a constant distance from the Range in all west-flowing rivers, the ubiquitous terraces, and river courses entrenched within their own flood-plain deposits of thick gritty to conglomeratic sand, are indicative of a constant disturbance with a gradual rise of the Range east of the knickpoint, wherefrom the coarse materials were carried by the fast west-flowing streams. There is a differential uplift across the plateau scarp together with a right-lateral offset. This epeirogenic tectonism is ascribed to the collision of the Eurasian and the subducting Indian plates and to a locking of their continental crusts. By early Pleistocene, with the MBT gradually dying off, continued plate movement caused a flexural bending of the plate by a moment generated at the back, and a possible delinking of the continental crust along the zone of subduction. The felexural bending ripped open the Precambrian regional faults. The differential uplift and the difference in the distances of the nodes on two sides of the major reactivated fault were possibly caused by a difference in the values of the flexural rigidity and the foundation modulus owing to a slight compositional difference of the constiuent rocks in the two sectors.

Synthesis of crustal seismic structure and implications for the concept of a slab gap beneath Coastal California

USGS Publications Warehouse

Brocher, T.M.; ten Brink, Uri S.; Abramovitz, T.

1999-01-01

Compilation of seismic transects across the central and northern California Coast Ranges provides evidence for the widespread tectonic emplacement beneath the margin of a slab of partially subducted oceanic lithosphere. The oceanic crust of this lithosphere can be traced landward from the former convergent margin (fossil trench), beneath the Coast Ranges, to at least as far east as the Coast Range/Great Valley boundary. Comparison of measured shear and compressional wave velocities in the middle crust beneath the Hayward fault with laboratory measurements suggests that the middle crust is a diabase (oceanic crust). Both of these observations are consistent with recent models of the high heat flow and age progression of Neogene volcanism along the Coast Ranges based on tectonic emplacement (stalling) of young, hot oceanic lithosphere beneath the margin, but appear to contradict the major predictions of the slab-gap or asthenospheric-window model. Finally, the Neogene volcanism and major strike-slip faults in the Coast Ranges occur within the thickest regions (>14 km thick) of the forearc, suggesting that the locations of Cenozoic volcanism and faulting along the margin are structurally controlled by the forearc thickness rather than being determined by the location of a broad slab gap.

Thermal regime of the San Andreas fault near Parkfield, California

USGS Publications Warehouse

Sass, J.H.; Williams, C.F.; Lachenbruch, A.H.; Galanis, S.P.; Grubb, F.V.

1997-01-01

Knowledge of the temperature variation with depth near the San Andreas fault is vital to understanding the physical processes that occur within the fault zone during earthquakes and creep events. Parkfield is near the southern end of the Coast Ranges segment of the San Andreas fault. This segment has higher mean heat flow than the Cape Mendocino segment to the northwest or the Mojave segment to the southeast. Boreholes were drilled specifically for the U.S. Geological Survey's Parkfield earthquake prediction experiment or converted from other uses at 25 sites within a few kilometers of the fault near Parkfield. These holes, which range in depth from 150 to over 1500 m, were intended mainly for the deployment of volumetric strain meters, water-level recorders, and other downhole instruments. Temperature profiles were obtained from all the holes, and heat flow values were estimated from 17 of them. For a number of reasons, including a paucity of thermal conductivity data and rugged local topography, the accuracy of individual determinations was not sufficiently high to document local variations in heat flow. Values range from 54 to 92 mW m-2, with mean and 95% confidence limits of 74 ?? 4 mW m-2. This mean is slightly lower than the mean (83 ?? 3) of 39 previously published values from the central Coast Ranges, but it is consistent with the overall pattern of elevated heat flow in the Coast Ranges, and it is transitional to the mean of 68 ?? 2 mW m-2 that characterizes the Mojave segment of the San Andreas fault immediately to the south. The lack of a heat flow peak near the fault underscores the absence of a frictional thermal anomaly and provides additional support for a very small resolved shear stress parallel to the San Andreas fault and the nearly fault-normal maximum compressive stress observed in this region. Estimates of subsurface thermal conditions indicate that the seismic-aseismic transition for the Parkfield segment corresponds to temperatures in the range of 350??-400??C. Increasing heat flow to the northwest of Parkfield corresponds to a transition from locked to creeping sections and to a shallowing of the base of seismicity and confirms the importance of temperature in controlling the thickness of the seismogenic crust. Lateral variations in heat flow do not appear to have any major role in determining the regularity of M5.5-6 earthquakes at Parkfield.

Gravity constraints on the geometry of the Big Bend of the San Andreas Fault in the southern Carrizo Plains and Pine Mountain egion

NASA Astrophysics Data System (ADS)

Altintas, Ali Can

The goal of this project is to combine gravity measurements with geologic observations to better understand the "Big Bend" of the San Andreas Fault (SAF) and its role in producing hydrocarbon-bearing structures in the southern Central Valley of California. The SAF is the main plate boundary structure between the Pacific and North American plates and accommodates ?35 mm/yr of dextral motion. The SAF can be divided into three main parts: the northern, central and southern segments. The boundary between the central and southern segments is the "Big Bend", which is characterized by an ≈30°, eastward bend. This fault curvature led to the creation of a series of roughly east-west thrust faults and the transverse mountain ranges. Four high-resolution gravity transects were conducted across locations on either side of the bend. A total of 166 new gravity measurements were collected. Previous studies suggest significantly inclined dip angle for the San Andreas Fault in the Big Bend area. Yet, our models indicate that the San Andreas Fault is near vertical in the Big Bend area. Also gravity cross-section models suggest that flower structures occur on either side of the bend. These structures are dominated by sedimentary rocks in the north and igneous rocks in the south. The two northern transects in the Carrizo plains have an ≈-70 mgal Bouguer anomaly. The SAF has a strike of ≈315° near these transects. The northern transects are characterized by multiple fault strands which cut marine and terrestrial Miocene sedimentary rocks as well as Quaternary alluvial valley deposits. These fault strands are characterized by ?6 mgal short wavelength variations in the Bouguer gravity anomaly, which correspond to low density fault gouge and fault splays that juxtapose rocks of varying densities. The southern transects cross part of the SAF with a strike of 285°, have a Bouguer anomaly of ≈-50 mgal and are characterized by a broad 15 mgal high. At this location the rocks on either side of the fault are Proterozoic - Cretaceous metamorphic or/and plutonic rocks. Previous work based on geologic mapping hypothesized the existence of a shallow, low angle Abel Mountain Thrust in which crystalline rocks were thrust over Miocene sedimentary rocks, near Apache Saddle. However, gravity models indicate the crystalline rocks are vertically extensive and form a positive flower structure bounded by high angle faults. Also, based on the thickness of fault adjacent sedimentary cover, the gravity models suggest a minimum exhumation of 5-6 km for crystalline rocks in the south. Assuming exhumation began with the switch from the transtensional San Gabriel Fault to transpressional San Andreas Fault at approximately 5 Ma, this indicates exhumation rates of 1 km/Ma. Overall, the broad gravity highs observed along the southern transects are due to uplift of basement rocks in this area.

Paleoseismology and tectonic geomorphology of the Pallatanga fault (Central Ecuador), a major structure of the South-American crust

NASA Astrophysics Data System (ADS)

Baize, Stéphane; Audin, Laurence; Winter, Thierry; Alvarado, Alexandra; Pilatasig Moreno, Luis; Taipe, Mercedes; Reyes, Pedro; Kauffmann, Paul; Yepes, Hugo

2015-05-01

The Pallatanga fault (PF) is a prominent NNE-SSW strike-slip fault crossing Central Ecuador. This structure is suspected to have hosted large earthquakes, including the 1797 Riobamba event which caused severe destructions to buildings and a heavy death toll (more than 12,000 people), as well as widespread secondary effects like landsliding, liquefaction and surface cracking. The scope of this study is to evaluate the seismic history of the fault through a paleoseismological approach. This work also aims at improving the seismotectonic map of this part of the Andes through a new mapping campaign and, finally, aims at improving the seismic hazard assessment. We show that the PF continues to the north of the previously mapped fault portion in the Western Cordillera (Rumipamba-Pallatanga portion) into the Inter-Andean Valley (Riobamba basin). Field evidences of faulting are numerous, ranging from a clear geomorphological signature to fault plane outcrops. Along the western side of the Riobamba basin, the strike-slip component seems predominant along several fault portions, with a typical landscape assemblage (dextral offsets of valleys, fluvial terrace risers and generation of linear pressure ridges). In the core of the inter-Andean valley, the main fault portion exhibits a vertical component along the c. 100 m-high cumulative scarp. The presence of such an active fault bounding the western suburbs of Riobamba drastically increases the seismic risk for this densely inhabited and vulnerable city. To the east (Peltetec Massif, Cordillera Real), the continuation of the Pallatanga fault is suspected, but not definitely proved yet. Based on the analysis of three trenches, we state that the Rumipamba-Pallatanga section of the PF experienced 4 (maybe 5) Holocene to Historical strong events (Mw > 7). The coseismic behavior of the fault is deduced from the occurrence of several colluvial wedges and layers associated with the fault activity and interbedded within the organic black soil sequence. According to a series of 14C datings, we document that these events occurred during the last 6500 years. The clear deformation of the shallowest layer (14C: 1633 AD) is most likely associated with the 1797 Riobamba earthquake. After retrodeforming one of the 3 trenches, we estimate coseismic vertical throws (0.70 to 0.90 m). Because of bad outcrop conditions, we could not determine the horizontal component of slip and we used the slip vector determined in a previous work with a tectonic geomorphology study. Assuming this slip vector, we obtain total coseismic offsets between 3.5 and 4.5 m, indicative of earthquake magnitudes around c. Mw 7.5. The estimated recurrence time intervals range between 1300 and 3000 years, indicating an average slip rate of c. 2.5 mm/a for the Rumipamba-Pallatanga section of the fault.

Constraints on Subduction Zone Coupling along the Philippine and Manila Trenches based on GPS and Seismological Data

NASA Astrophysics Data System (ADS)

Hamburger, M. W.; Johnson, K. M.; Nowicki, M. A. E.; Bacolcol, T. C.; Solidum, R., Jr.; Galgana, G.; Hsu, Y. J.; Yu, S. B.; Rau, R. J.; McCaffrey, R.

2014-12-01

We present results of two techniques to estimate the degree of coupling along the two major subduction zone boundaries that bound the Philippine Mobile Belt, the Philippine Trench and the Manila Trench. Convergence along these plate margins accommodates about 100 mm/yr of oblique plate motion between the Philippine Sea and Sundaland plates. The coupling estimates are based on a recently acquired set of geodetic data from a dense nationwide network of continuous and campaign GPS sites in the Philippines. First, we use a kinematic, elastic block model (tdefnode; McCaffrey, 2009) that combines existing fault geometries, GPS velocities and focal mechanism solutions to solve for block rotations, fault coupling, and intra-block deformation. Secondly, we use a plate-block kinematic model described in Johnson (2013) to simultaneously estimate long-term fault slip rates, block motions and interseismic coupling on block-bounding faults. The best-fit model represents the Philippine Mobile Belt by 14 independently moving rigid tectonic blocks, separated by active faults and subduction zones. The model predicts rapid convergence along the Manila Trench, decreasing progressively southwards, from > 100 mm/yr in the north to less than 20 mm/yr in the south at the Mindoro Island collision zone. Persistent areas of high coupling, interpreted to be asperities, are observed along the Manila Trench slab interface, in central Luzon (16-18°N) and near its southern and northern terminations. Along the Philippine Trench, we observe ~50 mm/yr of oblique convergence, with high coupling observed at its central and southern segments. We identify the range of allowable coupling distributions and corresponding moment accumulation rates on the two subduction zones by conducting a suite of inversions in which the total moment accumulation rate on a selected fault is fixed. In these constrained moment inversions we test the range of possible solutions that meet criteria for minimum, best-fit, and maximum coupling that still fit the data, based on reduced chi-squared calculations. In spite of the variable coupling, the total potential moment accumulation rate along each of the two subduction zones is estimated to range from 3.98 x 1019 to 2.24 x 1020 N-m yr-1, equivalent to a magnitude Mw 8.4 to 8.9 earthquake per 100 years.

Geology of the undeveloped oil and gas fields of Central Offshore Santa Maria Basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milton, J.D.; Edwards, E.B.; Heck, R.G.

1996-01-01

Two prominent subsurface structural features of the Central Offshore Santa Maria Basin are the Hosgri fault system and the associated anticlinal fold trend. Exploratory drilling and 3D seismic mapping have delineated a series of oil and gas fields along this trend which underlie four federal units and one non-unitized lease. The units are named after local geography and are called the Lion Rock, Point Sal, Purisima Point and Santa Maria Units. The individual lease, OCS P-0409, overlies the San Miguel field. The Hosgri fault system trends northwest-southeast and effectively forms the eastern boundary of the oil and gas province. Lyingmore » semi-parallel with the fault are several anticlinal culminations which have trapped large volumes of oil and gas in the fractured Montery Formation. The Monterey is both source and reservoir rock, averaging 300 meters n thickness throughout the Central Basin. Development of the Monterey Formation as a reservoir rock was through diagensis and tectonism with resulting porosities-from 15 to 20% and permeability up to one Darcy. These parameters coupled with a high geothermal gradient facilitate the inflow rates of the viscous Monterey oil. Some 24 exploration and delineation wells have been drilled in this area and tested at rates ranging from a few hundred to several thousand barrels per day. Estimated oil reserves in the Central Offshore Santa Maria Basin total approximately 1 billion barrels.« less

Geology of the undeveloped oil and gas fields of Central Offshore Santa Maria Basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milton, J.D.; Edwards, E.B.; Heck, R.G.

1996-12-31

Two prominent subsurface structural features of the Central Offshore Santa Maria Basin are the Hosgri fault system and the associated anticlinal fold trend. Exploratory drilling and 3D seismic mapping have delineated a series of oil and gas fields along this trend which underlie four federal units and one non-unitized lease. The units are named after local geography and are called the Lion Rock, Point Sal, Purisima Point and Santa Maria Units. The individual lease, OCS P-0409, overlies the San Miguel field. The Hosgri fault system trends northwest-southeast and effectively forms the eastern boundary of the oil and gas province. Lyingmore » semi-parallel with the fault are several anticlinal culminations which have trapped large volumes of oil and gas in the fractured Montery Formation. The Monterey is both source and reservoir rock, averaging 300 meters n thickness throughout the Central Basin. Development of the Monterey Formation as a reservoir rock was through diagensis and tectonism with resulting porosities-from 15 to 20% and permeability up to one Darcy. These parameters coupled with a high geothermal gradient facilitate the inflow rates of the viscous Monterey oil. Some 24 exploration and delineation wells have been drilled in this area and tested at rates ranging from a few hundred to several thousand barrels per day. Estimated oil reserves in the Central Offshore Santa Maria Basin total approximately 1 billion barrels.« less

Analysis of La Dehesa paleo-landslide. Central Pre-Andes of Argentina

NASA Astrophysics Data System (ADS)

Tapia Baldis, Carla; Rothis, Luis Martín; Perucca, Laura; Esper Angillieri, María; Vargas, Horacio; Ponce, David; Allis, Carlos

2018-04-01

The main objective of this paper is to consider the influence of Quaternary faults as likely triggering factor for rockslides occurrence in the Central Pre-Andes, a region with intense shallow seismic activity. A rockslide deposit was selected as study case, placed in the western flank of La Dehesa and Talacasto (DT) range (31°3‧37″ S and 68°46‧ 8″ W). Applied methodology includes the characterization of main discontinuities, reconstruction of the topography using a high-resolution digital elevation model, safety factor calculation along the sliding surface and, Newmark displacements estimation for three different hypothetical seismic scenarios, recreated from existing neotectonic local information. Equilibrium-limit method's results confirm that study case, La Dehesa rockslide (LDR), had a stable and safe slope's configuration under static conditions. However, a seismic horizontal coefficient between 0.2 and 0.3 decreases safety factor below the safety threshold. Newmark's displacements for different seismic reconstructed scenarios varies between 4.1 and 15.9 cm, values that agreed with a coherent failure process, likely triggered by Pleistocene to Holocene seismogenic sources in Central Pre-Andes. LDR trigger could be assigned mainly to an earthquake related to La Dehesa Quaternary fault (LDF) activity; however, similar movements produced by neighboring faults should not be discarded. LDR triggering related to climatic conditions is despised. Finally, the methodology presented in this work is easy to reproduce and may be applied to other rockslides located in the mountainous areas of the Central Pre-Andes of Argentina.

Isothermal thermoluminescence dating of K-feldspar from sediments to determine fault slip rates: development and assessment

NASA Astrophysics Data System (ADS)

Rhodes, E. J.; Roder, B. J.; Lawson, M. J.; Dolan, J. F.; McGill, S. F.; McAuliffe, L.

2012-04-01

Faults in California accommodate most of the relative motion between the Pacific and North American tectonic plates, along either one main strike-slip fault, - the San Andreas fault - or a network of sub-parallel faults (e.g., the San Jacinto, Elsinore and San Andreas faults). Slip is also accommodated along many other associated faults and folds, and the region suffers frequent damaging earthquakes. Contemporary movements of different fault-bounded blocks are relatively well established on decadal timescales using remote sensing and GPS, and on timescales of 106 to 107 years, by dating offset geologic features with radiometric methods. However, on timescales of decades to several hundred thousand years, determining total fault offset and mean slip rate is harder. Critical questions for understanding fault dynamics and improving earthquake risk assessment include the degree to which slip is clustered into episodes of more rapid movement, and how slip is accommodated by different sub-parallel faults. In many cases, streams with offset courses can be recognised, and in some cases offset terrace surfaces can be located, especially when using LiDAR data to complement field mapping. Radiocarbon and terrestrial cosmogenic nuclides have been used to date these features, but both have limitations of age range, sample suitability and availability. OSL (optically stimulated luminescence) and IRSL (infra-red stimulated luminescence) have great potential to complement these techniques, though the characteristics of quartz in some parts of southern California are suboptimal, displaying low sensitivity and other limitations. In order to overcome these limitations encountered using quartz OSL, we are developing a new geochronometer based on the isothermal thermoluminescence (ITL) signal of K feldspar measured at 250°C. Preliminary ITL age estimates from the paleoseismic site of El Paso Peaks on the Central Garlock fault in the Mojave Desert, California, agree well with a well-established radiocarbon chronology based on 29 samples spanning the last 7,000 years (Dawson et al., 2003). We examine the basis of this new ITL approach and assess its potential for application within California and beyond. Reference cited Dawson, T.E., McGill, S.F. and Rockwell, T.K. 2003 Irregular recurrence of paleoearthquakes along the central Garlock fault near El Paso peaks, California. Journal of Geophysical Research 108, No. B7, 2356, doi:10.1029/2001JB001744.

Cenozoic volcanic geology and probable age of inception of basin-range faulting in the southeasternmost Chocolate Mountains, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowe, B.M.

1978-02-01

A complex sequence of Oligocene-age volcanic and volcaniclastic rocks form a major volcanic center in the Picacho area of the southeasternmost Chocolate Mountains, Imperial County, California. Basal-volcanic rocks consist of lava flows and flow breccia of trachybasalt, pyroxene rhyodacite, and pyroxene dacite (32 My old). These volcanic rocks locally overlie fanglomerate and rest unconformably on pre-Cenozoic basement rocks. South and southeast of a prominent arcuate fault zone in the central part of the area, the rhyolite ignimbrite (26 My old) forms a major ash-flow sheet. In the southwestern part of the Picacho area the rhyolite ignimbrite interfingers with and ismore » overlain by dacite flows and laharic breccia. The rhyolite ignimbrite and the dacite of Picacho Peak are overlapped by lava flows and breccia of pyroxene andesite (25 My old) that locally rest on pre-Cenozoic basement rocks. The volcanic rocks of the Picacho area form a slightly bimodal volcanic suite consisting chiefly of silicic volcanic rocks with subordinate andesite. Late Miocene augite-olivine basalt is most similar in major-element abundances to transitional alkali-olivine basalt of the Basin and Range province. Normal separation faults in the Picacho area trend northwest and north parallel to major linear mountain ranges in the region. The areal distribution of the 26-My-old rhyolite ignimbrite and the local presence of megabreccia and fanglomerate flanking probable paleohighs suggest that the ignimbrite was erupted over irregular topography controlled by northwest- and north-trending probable basin-range faults. These relations date the inception of faulting in southeasternmost California at pre-26 and probably pre-32 My ago. A transition of basaltic volcanism in the area is dated at 13 My ago. 9 figures, 2 tables.« less

Characterization of the Marcellus Shale based on computer-assisted correlation of wireline logs in Virginia and West Virginia

USGS Publications Warehouse

Enomoto, Catherine B.; Olea, Ricardo A.; Coleman, James L.

2014-01-01

The Middle Devonian Marcellus Shale in the Appalachian basin extends from central Ohio on the west to eastern New York on the east, and from north-central New York on the north to northern Tennessee on the south. Its thickness ranges from 0 feet (ft) where it pinches out to the west to as much as 700 ft in its eastern extent. Within the Broadtop synclinorium, the thickness of the Marcellus Shale ranges from 250 to 565 ft. Although stratigraphic complexities have been documented, a significant range in thickness most likely is because of tectonic thickening from folds and thrust faults. Outcrop studies in the Valley and Ridge and Appalachian Plateaus provinces illustrate the challenges of interpreting the relation of third-order faults, folds, and “disturbed” zones to the regional tectonic framework. Recent field work within the Valley and Ridge province determined that significant faulting and intraformational deformation are present within the Marcellus Shale at the outcrop scale. In an attempt to determine if this scale of deformation is detectable with conventional wireline logs, petrophysical properties (primarily mineralogy and porosity) were measured by interpretation of gamma-ray and bulk-density logs. The results of performing a statistical correlation of wireline logs from nine wells indicated that there are discontinuities within the Millboro Shale (undifferentiated Marcellus Shale and Mahantango Formation) where there are significant thickness differences between wells. Also, some intervals likely contain mineralogy that makes these zones more prone to layer-shortening cleavage duplexes. The Correlator program proved to be a useful tool in a region of contractional deformation.

Earthquake hypocenters and focal mechanisms in central Oklahoma reveal a complex system of reactivated subsurface strike-slip faulting

USGS Publications Warehouse

McNamara, Daniel E.; Benz, Harley M.; Herrmann, Robert B.; Bergman, Eric A.; Earle, Paul S.; Holland, Austin F.; Baldwin, Randy W.; Gassner, A.

2015-01-01

The sharp increase in seismicity over a broad region of central Oklahoma has raised concern regarding the source of the activity and its potential hazard to local communities and energy industry infrastructure. Since early 2010, numerous organizations have deployed temporary portable seismic stations in central Oklahoma in order to record the evolving seismicity. In this study, we apply a multiple-event relocation method to produce a catalog of 3,639 central Oklahoma earthquakes from late 2009 through 2014. RMT source parameters were determined for 195 of the largest and best-recorded earthquakes. Combining RMT results with relocated seismicity enabled us to determine the length, depth and style-of-faulting occurring on reactivated subsurface fault systems. Results show that the majority of earthquakes occur on near vertical, optimally oriented (NE-SW and NW-SE), strike-slip faults in the shallow crystalline basement. These are necessary first order observations required to assess the potential hazards of individual faults in Oklahoma.

Petrographic and chemical reconnaissance study of some granitic and gneissic rocks near the San Andreas fault from Bodega Head to Cajon Pass, California

USGS Publications Warehouse

Ross, Donald C.

1972-01-01

This petrographic and chemical study is based on reconnaissance sampling of granitic and related gneissic rock in the California Coast and Transverse Ranges. In the Coast Ranges, granitic rocks are restricted to an elongate belt, the Salinian block, between the San Andreas and Sur-Nacimiento fault zones. These rocks have a considerable compositional range, but are dominantly quartz monzonite and granodiorite. Moist of the Salinian block seems to be a structurally coherent basement block of chemically related granitic rocks. However, on both the east and the west sides of the block, gneiss crops out in abundance; these rocks may be structurally separate from the main part of the Salinian block. In the Transverse Ranges, the granitic and related rocks are dominantly of granodiorite composition, and in many areas granitic and gneissic rocks are intimately intermixed.Chemically the rocks of the California Coast and Transverse Ranges are somewhat intermediate in character between those of the east-central part of the Sierra Nevada batholith and those of the western part of the Sierra Nevada batholith and the southern California batholith. Probably the closest similarity is to the east-central Sierra Nevada rocks, but the rocks of the Coast and Transverse Ranges are somewhat higher in Al2O3 and lower in K2O than Sierran rocks of the comparable SiO2 content.Granitic basement rocks of the Salinian block are now anomalously sandwiched between Franciscan terranes. The petrographic and chemical data are compatible with the concept that the Salinian rocks were originally part of the great batholithic belt along the west coast, which is exemplified by the Sierra Nevada hatholith. It also seems most likely that the Salinian block was transported from somewhere south of the Sierra Nevada batholith by large-scale right-lateral movement along the San Andreas fault zone.

New insights into the tectonic evolution of the Boconó Fault, Mérida Andes, Venezuela

NASA Astrophysics Data System (ADS)

Backé, G.

2006-12-01

The Boconó fault is a major right-lateral strike-slip fault that cuts along strike the Mérida Andes in Venezuela. The uplift of this mountain range started in the Miocene as a consequence of the relative oblique convergence between two lithospheric units named the Maracaibo block to the northwest and the Guyana shield to the southeast. Deformation in the Mérida Andes is partitioned between a strike-slip component along the Boconó fault and shortening perpendicular to the belt. Distinctive features define the Boconó fault: it is shifted southward relative to the chain axis and it does not have a continuous and linear trace but is composed of several fault segments of different orientations striking N35°E to N65°E. Quaternary fault strike-slip motion has been evidenced by various independent studies. However, onset of the strike-slip motion, fault offset and geometry at depth remains a matter of debate. Our work, based on morphostructural analyses of satellite and digital elevation model imagery, provides new data on both the geometry and the tectonic evolution of this major structure. We argue that the Boconó fault affects only the upper crust and connects at depth to a décollement. Consequently, it can not be considered as a plate boundary. The Boconó fault does however form the boundary between two different tectonic areas in the central part of the Mérida Andes as revealed by the earthquake focal mechanisms. South of the Boconó fault, the focal mechanisms are mainly compressional and reverse oblique-slip in agreement with NW SE shortening in the foothills. North of the Boconó fault, extensional and strike-slip deformation dominates. Microtectonic measurements collected in the central part of the Boconó fault are characterized by polyphased tectonics. The dextral shearing along the fault is superimposed to reverse oblique-slip to reverse motion, showing that initiation of transcurrent movement is more likely to have occurred after a certain amount of shortening. The present day strain partitioning along the Mérida Andes seems to be younger than the rise of the chain and coeval with the initiation of right-lateral shearing along the Boconó fault, which would have then initiated in the Pliocene. The Mérida Andes can be therefore considered as a case study of the kinematic evolution of a major strike-slip fault.

Cenozoic structural history of selected areas in the eastern Great Basin, Nevada-Utah

USGS Publications Warehouse

Anderson, R. Ernest

1983-01-01

The Confusion Range structural trough (CRST) of west-central Utah predates the Oligocene rocks that are exposed along it. The northern part of the axial region of the CRST is complicated by structures that include reverse faults and associated folds, a large-amplitude mushroom fold, and belts of sharply flexed to overturned strata some of which are fault bounded. These structures, which also predate the Oligocene rocks, formed in a compressional regime that has been interpreted as resulting from thin-skinned gravitational gliding toward the axis of the CRST. Study of the sparse Tertiary rocks that are scattered along the axial region of the CRST reveals abundant evidence of Oligocene and younger deformation. The chief evidence includes (1) widespread Oligocene and Miocene coarse clastic rocks, many of which are conglomerates, that attest to local and distant tectonism, (2) faults that range from high-angle structures generally with less than 100 m of normal displacement to low-angle attenuation faults some of which may have large displacements, and (3) open asymmetric folds. Together with the distribution of sheet-form bodies of ash-flow tuffs, the Oligocene stratigraphic record allows for paleogeographic reconstruction of a lacustrine basin across what is now the northern Confusion Range and one or more basins in the southern part of the CRST. The basins are inferred to have been fault controlled by reactivation of previously formed faults or steep fold flanks. They may have been localized by differential vertical movements similar to those that produced the older systems of folds and faults. Parts of early formed basins were cannibalized as local syndepositional deformation took place in the axial region of the CRST. Both limbs of the CRST have been modified by folds that involve Oligocene rocks. Some of these folds appear to be genetically related to displacements on faults that bound them. They may record thin-skinned Neogene tectonic displacements toward the axis of the CRST. The most intensely faulted and tilted rocks along the axis of the CRST are located in the Tunnel Spring Mountains where Miocene(?) extension on closely spaced listric faults produced as much as 70 percent extension locally. Three episodes of Oligocene-Miocene deformation, all interpreted to have formed in an extensional environment, are recognized in the Tunnel Spring Mountains. The nearby Burbank Hills area may have been involved in the same deformational episodes, though there the relationships are not as clear-cut nor does evidence occur of extreme extension. Tight asymmetric folds in the Burbank Hills are interpreted as drape structures formed over buried normal faults. Other structures along the southern CRST have fold-like forms, but they result from cross-strike alternations in fault-related tilt directions, and they formed in an extensional stress regime. Least-principal stress directions inferred from orientations of extensional structures vary from ENE-WSW in the southern Tunnel Spring Mountains to approximately E-W in the Disappointment Hills and NW-SE in selected areas east of the axis of the CRST. The size, geographic distribution, and new data on the age of areas of major extensional faulting preclude previously published interpretations that the extension is related to major east-directed overthrusting of the Sevier orogeny in areas east of the hinterland of west-central Utah.

Seismic imaging of the southern California plate-boundary around the South-Central Transverse Ranges using double-difference tomography

NASA Astrophysics Data System (ADS)

Share, P. E.; Ben-Zion, Y.; Thurber, C. H.; Zhang, H.; Guo, H.

2017-12-01

We derive P and S seismic velocities within and around the South-Central Transverse Ranges section of the San Andreas Fault (SAF), using a new double-difference tomography algorithm incorporating both event-pair and station-pair differential times. The event-pair data can determine high-resolution relative earthquake locations and resolve fine-scale structure in seismogenic zones, whereas station-pair data allow for better absolute locations and higher resolution of structure near the surface where stations are most dense. The tomographic results are based on arrival times of P and S waves generated by 17,753 M>1 local events from 1/1/2010 to 6/30/2015 recorded by 259 stations within a 222 km x 164 km region. The resulting P and S velocity models include low velocities along major fault segments and across-fault velocity contrasts. For example, at depths <7 km, low velocity anomalies delineate the SAF from Cajon Pass to Coachella Valley, with the exception around San Gorgonio Pass (SGP) where a relatively fast rock body cuts across the fault. Extensive faulting and Pelona schist manifest as low velocities throughout the San Bernardino Basin (SBB). High velocity granites abut the SBB to the SW and NE, forming prominent velocity contrasts across the northern San Jacinto Fault Zone (SJFZ) and the SAF, respectively. At depths of 9-11 km, the models also show a velocity contrast with an areal extent of >50 km parallel to the SAF around Coachella Valley but offset to the NE by 13 km. This is interpreted to mark a dipping section of the SAF that separates granites at depth in the SW from gneisses and schists in the NE. Analysis of fault zone head waves propagating along these sections of the SAF and SJFZ show that major bimaterial interfaces are associated with the observed velocity contrasts. Additional features within the models include elongated low velocity anomalies extending from the SJFZ trifurcation area, which itself has associated low velocity at great depth (>14 km), to the Elsinore Fault in the SW. Moreover, a deep (>13 km) velocity contrast appears beneath the SBB with an east-west strike oblique to both the northern SJFZ and SAF traces. The latter is potentially related to the ancestral Banning Fault, which dips to the north, separating low velocity Pelona schist in the north from high velocity granites in the south.

MC-13 Syrtis Major Region

NASA Technical Reports Server (NTRS)

1994-01-01

Mars digital-image mosaic merged with color of the MC-13 quadrangle, Syrtis Major region of Mars. The central part is dominated by dark dust and lava flows of the Syrtis Major Planitia region. These lava flows are partly bounded to the east by a large depression, Isidis basin, which contains smooth plains, and to the west and north by heavily cratered and moderately faulted highlands. Latitude range 0 to 30 degrees, longitude range -90 to -45 degrees.

Upper mantle diapers, lower crustal magmatic underplating, and lithospheric dismemberment of the Great Basin and Colorado Plateau regions, Nevada and Utah; implications from deep MT resistivity surveying

NASA Astrophysics Data System (ADS)

Wannamaker, P. E.; Doerner, W. M.; Hasterok, D. P.

2005-12-01

In the rifted Basin and Range province of the southwestern U.S., a common faulting model for extensional basins based e.g. on reflection seismology data shows dominant displacement along master faults roughly coincident with the main topographic scarp. On the other hand, complementary data such as drilling, earthquake focal mechanisms, volcanic occurrences, and trace indicators such as helium isotopes suggest that there are alternative geometries of crustal scale faulting and material transport from the deep crust and upper mantle in this province. Recent magnetotelluric (MT) profiling results reveal families of structures commonly dominated by high-angle conductors interpreted to reflect crustal scale fault zones. Based mainly on cross cutting relationships, these faults appear to be late Cenozoic in age and are of low resistivity due to fluids or alteration (including possible graphitization). In the Ruby Mtns area of north-central Nevada, high angle faults along the margins of the core complex connect from near surface to a regional lower crustal conductor interpreted to contain high-temperature fluids and perhaps melts. Such faults may exemplify the high angle normal faults upon which the major earthquakes of the Great Basin appear to nucleate. A larger-scale transect centered on Dixie Valley shows major conductive crustal-scale structures connecting to conductive lower crust below Dixie Valley, the Black Rock desert in NW Nevada, and in east-central Nevada in the Monitor-Diamond Valley area. In the Great Basin-Colorado Plateau transition of Utah, the main structures revealed are a series of nested low-angle detachment structures underlying the incipient development of several rift grabens. All these major fault zones appear to overlie regions of particularly conductive lower crust interpreted to be caused by recent basaltic underplating. In the GB-CP transition, long period data show two, low-resistivity upper mantle diapirs underlying the concentrated conductive lower crust and nested faults, and these are advanced as melt source regions for the underplating. MT, with its wide frequency bandwidth, allows views of nearly a complete melting and emplacement process, from mantle source region, through lower crustal intrusion, to brittle regime deformational response.

The Lithosphere-asthenosphere Boundary beneath the South Island of New Zealand

NASA Astrophysics Data System (ADS)

Hua, J.; Fischer, K. M.; Savage, M. K.

2017-12-01

Lithosphere-asthenosphere boundary (LAB) properties beneath the South Island of New Zealand have been imaged by Sp receiver function common-conversion point stacking. In this transpressional boundary between the Australian and Pacific plates, dextral offset on the Alpine fault and convergence have occurred for the past 20 My, with the Alpine fault now bounded by Australian plate subduction to the south and Pacific plate subduction to the north. This study takes advantage of the long-duration and high-density seismometer networks deployed on or near the South Island, especially 29 broadband stations of the New Zealand permanent seismic network (GeoNet). We obtained 24,980 individual receiver functions by extended-time multi-taper deconvolution, mapping to three-dimensional space using a Fresnel zone approximation. Pervasive strong positive Sp phases are observed in the LAB depth range indicated by surface wave tomography (Ball et al., 2015) and geochemical studies. These phases are interpreted as conversions from a velocity decrease across the LAB. In the central South Island, the LAB is observed to be deeper and broader to the west of the Alpine fault. The deeper LAB to the west of the Alpine fault is consistent with oceanic lithosphere attached to the Australian plate that was partially subducted while also translating parallel to the Alpine fault (e.g. Sutherland, 2000). However, models in which the Pacific lithosphere has been underthrust to the west past the Alpine fault cannot be ruled out. Further north, a zone of thin lithosphere with a strong and vertically localized LAB velocity gradient occurs to the west of the fault, juxtaposed against a region of anomalously weak LAB conversions to the east of the fault. This structure, similar to results of Sp imaging beneath the central segment of the San Andreas fault (Ford et al., 2014), also suggests that lithospheric blocks with contrasting LAB properties meet beneath the Alpine fault. The observed variations in LAB properties indicate strong modification of the LAB by the interplay of convergence and strike-slip deformation along and across this transpressional plate boundary.

GIA induced intraplate seismicity in northern Central Europe

NASA Astrophysics Data System (ADS)

Brandes, Christian; Steffen, Holger; Steffen, Rebekka; Wu, Patrick

2015-04-01

Though northern Central Europe is regarded as a low seismicity area (Leydecker and Kopera, 1999), several historic earthquakes with intensities of up to VII affected the area in the last 1200 years (Leydecker, 2011). The trigger for these seismic events is not sufficiently investigated yet. Based on the combination of historic earthquake epicentres with the most recent fault maps we show that the historic seismicity concentrated at major reverse faults. There is no evidence for significant historic earthquakes along normal faults in northern Central Europe. The spatial and temporal distribution of earthquakes (clusters that shift from time to time) implies that northern Central Europe behaves like a typical intraplate tectonic region as demonstrated for other intraplate settings (Liu et al., 2000) We utilized Finite Element models that describe the process of glacial isostatic adjustment to analyse the fault behaviour. We use the change in Coulomb Failure Stress (dCFS) to represent the minimum stress required to reach faulting. A negative dCFS value indicates that the fault is stable, while a positive value means that GIA stress is potentially available to induce faulting or cause fault instability or failure unless released temporarily by an earthquake. The results imply that many faults in Central Europe are postglacial faults, though they developed outside the glaciated area. This is supported by the characteristics of the dCFS graphs, which indicate the likelihood that an earthquake is related to GIA. Almost all graphs show a change from negative to positive values during the deglaciation phase. This observation sheds new light on the distribution of post-glacial faults in general. Based on field data and the numerical simulations we developed the first consistent model that can explain the occurrence of deglaciation seismicity and more recent historic earthquakes in northern Central Europe. Based on our model, the historic seismicity in northern Central Europe can be regarded as a kind of aftershock sequence of the GIA induced-seismicity. References Leydecker, G. and Kopera, J.R. Seismological hazard assessment for a site in Northern Germany, an area of low seismicity. Engineering Geology 52, 293-304 (1999). Leydecker, G. Erdbebenkatalog für die Bundesrepublik Deutschland mit Randgebieten für die Jahre 800-2008. Geologisches Jahrbuch Reihe E, 198 pp., (2011) Liu, M., Stein, S. and Wang, H. 2000 years of migrating earthquakes in north China: How earthquakes in midcontinents differ from those at plate boundaries. Lithosphere 3, 128-132, (2011).

Active faulting in the central Betic Cordillera (Spain): Palaeoseismological constraint of the surface-rupturing history of the Baza Fault (Central Betic Cordillera, Iberian Peninsula)

NASA Astrophysics Data System (ADS)

Castro, J.; Martin-Rojas, I.; Medina-Cascales, I.; García-Tortosa, F. J.; Alfaro, P.; Insua-Arévalo, J. M.

2018-06-01

This paper on the Baza Fault provides the first palaeoseismic data from trenches in the central sector of the Betic Cordillera (S Spain), one of the most tectonically active areas of the Iberian Peninsula. With the palaeoseismological data we constructed time-stratigraphic OxCal models that yield probability density functions (PDFs) of individual palaeoseismic event timing. We analysed PDF overlap to quantitatively correlate the walls and site events into a single earthquake chronology. We assembled a surface-rupturing history of the Baza Fault for the last ca. 45,000 years. We postulated six alternative surface rupturing histories including 8-9 fault-wide earthquakes. We calculated fault-wide earthquake recurrence intervals using Monte Carlo. This analysis yielded a 4750-5150 yr recurrence interval. Finally, compared our results with the results from empirical relationships. Our results will provide a basis for future analyses of more of other active normal faults in this region. Moreover, our results will be essential for improving earthquake-probability assessments in Spain, where palaeoseismic data are scarce.

Inherited crustal features and tectonic blocks of the Transantarctic Mountains: An aeromagnetic perspective (Victoria Land, Antarctica)

NASA Astrophysics Data System (ADS)

Ferraccioli, F.; Bozzo, E.

1999-11-01

Aeromagnetic images covering a sector of the Transantarctic Mountains in Victoria Land as well as the adjacent Ross Sea are used to study possible relationships between tectonic blocks along the Cenozoic and Mesozoic West Antarctic rift shoulder and prerift features inherited mainly from the Paleozoic terranes involved in the Ross Orogen. The segmentation between the Prince Albert Mountains block and the Deep Freeze Range-Terra Nova Bay region is related to an inherited NW to NNW ice-covered boundary, which we name the "central Victoria Land boundary." It is interpreted to be the unexposed, southern continuation of the Ross age back arc Exiles thrust system recognized at the Pacific coast. The regional magnetic high to the west of the central Victoria Land boundary is attributed to Ross age calc-alkaline back arc intrusives forming the in-board Wilson "Terrane," thus shifting the previously interpreted Precambrian "shield" at least 100 km farther to the west. The high-frequency anomalies of the Prince Albert Mountains and beneath the Polar Plateau show that this region was extensively effected by Jurassic tholeiitic magmatism; NE to NNE trending magnetic lineations within this pattern could reflect Cretaceous and/or Cenozoic faulting. The western and eastern edges of the Deep Freeze Range block, which flanks the Mesozoic Rennick Graben, are marked by two NW magnetic lineaments following the Priestley and Campbell Faults. The Campbell Fault is interpreted to be the reactivated Wilson thrust fault zone and is the site of a major isotopic discontinuity in the basement. To the east of the Campbell Fault, much higher amplitude magnetic anomalies reveal mafic-ultramafic intrusives associated with the alkaline Meander Intrusive Group (Eocene-Miocene). These intrusives are likely genetically linked to the highly uplifted Southern Cross Mountains block. The NW-SE trends crossing the previously recognized ENE trending Polar 3 Anomaly offshore of the Southern Cross Mountains are probably linked to Cenozoic reactivation of the Paleozoic Wilson-Bowers suture zone as proposed from recent seismic interpretations. The ENE trend of the anomaly may also be structural, and if so, it could reflect an inherited fault zone of the cratonal margin.

Crustal and uppermost mantle structure and deformation in east-central China

NASA Astrophysics Data System (ADS)

Li, H.; Yang, X.; Ouyang, L.; Li, J.

2017-12-01

We conduct a non-linear joint inversion of receiver functions and Rayleigh wave dispersions to obtain the crustal and upper mantle velocity structure in east-central China. In the meanwhile, the lithosphere and upper mantle deformation beneath east-central China is also evaluated with teleseismic shear wave splitting measurements. The resulting velocity model reveals that to the east of the North-South Gravity Lineament, the crust and the lithosphere are significantly thinned. Furthermore, three extensive crustal/lithospheric thinning sub-regions are clearly identified within the study area. This indicates that the modification of the crust and lithosphere in central-eastern China is non-uniform due to the heterogeneity of the lithospheric strength. Extensive crustal and lithospheric thinning could occur in some weak zones such as the basin-range junction belts and large faults. The structure beneath the Dabie orogenic belt is complex due to the collision between the North and South China Blocks during the Late Paleozoic-Triassic. The Dabie orogenic belt is generally delineated by a thick crust with a mid-crust low-velocity zone and a two-directional convergence in the lithospheric scale. Obvious velocity contrast exhibits in the crust and upper mantle at both sides of the Tanlu fault, which suggests the deep penetration of this lithospheric-scale fault. Most of our splitting measurements show nearly E-W trending fast polarization direction which is slightly deviating from the direction of plate motion. The similar present-day lithosphere structure and upper mantle deformation may imply that the eastern NCC and the eastern SCB were dominated by a common dynamic process after late Mesozoic, i.e., the westward subduction of Pacific plate and the retreat of the subduction plate. The westward subduction of the Philippine plate and the long-range effects of the collision between the Indian plate and Eurasia plate during Cenozoic may have also contributed to the present velocity structure and stress environment of eastern China.

Fault patterns in the Strait of Messina, Southern Italy

NASA Astrophysics Data System (ADS)

Fu, L.; Krastel, S.; Chiocci, F. L.; Ridente, D.; Schulten, I.; Cukur, D.; Gross, F.; Bialas, J.

2013-12-01

The Strait of Messina is one of the seismically most active areas in the Mediterranean region. The structural and seismotectonic settings of the area are still poorly understood. A number of faults have been identified on new high-resolution 2D seismic data collected in December 2011/January 2012. Most of the faults trending NWW-SEE are high angle (>60°) faults; they are located in the northern (off Calabria) and southern part of the Messina Straits. A number of faults identified in the central part of the Straits along the central channel or on the Calabrian side strike NNE-SSW or NNW-NNE. They dip at intermediate (30°-60°) to low (<30°) angles. The NNW-ward motion of Sicily and the NE-ward motion of Calabria indicate that faults in the strait are transtensional and that the strait is basically an asymmetric pull-apart basin (half-graben) under transtensional condition. This is confirmed by the appearances of negative flower structures, an en-echelon fault zone, and two main depocentres in the northern and central part of the straits, respectively. A fault located close to the Sicilian coast between Taormina and Briga may represent the so called Taormina fault. The existence of this fault is heavily debated in literatures. As the Strait of Messina is a transtensional basin, the Taormina fault should be a surface fault, which may outcrop very close to the Ionian coast off Sicily rather than a blind basement fault as identified on our data. Faults in the north may be the source of the 1908 Messina earthquake, because the area is in an early mature developing stage of a pull-apart basin. The cross-basin faults transecting this part of the basin would increase the slippage and the potential for large-magnitude earthquakes.

Active tectonics of the Qom region, Central Iran

NASA Astrophysics Data System (ADS)

Hollingsworth, J.; Fattahi, M.; Jackson, J. A.; Talebian, M.; Nazari, H.; Bahroudi, A.

2009-12-01

Between 50-57°E shortening across the Arabian-Eurasian collision zone is accommodated primarily in the Zagros and Alborz mountains of Iran, which bound the relatively aseismic Central Iranian block. Both the lack of seismicity and the minor variation in GPS velocities across Central Iran suggest this region plays a negligible role in accommodating Arabia-Eurasia shortening at the present day. We examine recent deformation in the Qom region, which lies 100 km south of Tehran within the Central Iran block. This region is notable for a number of large earthquakes over the last 30 years: 1980.12.18 (Mw 6.0), 1980.12.22 (Mw 5.7), and 2007.06.18 (Mw 5.4). Body-waveform modeling of these events indicates N-S shortening on a S-dipping thrust fault which projects to the surface along the Qom thrust. Evidence for longer-term uplift is indicated by the increased topography south of the fault, and the exposure of folded Miocene (U. Red Fmtn) and Late Oligocene (Qom Fmtn) deposits. River incision has resulted in numerous river terraces, and in one location an alluvial fan has been offset across the fault. Four samples were collected from the surface of this fan and their ages determined using OSL dating. The results indicate fan abandonment at ~30 kybp. A DEM of the fan was produced using kinematic GPS surveying data, from which 1.0±0.3 m vertical offset was measured. A minimum uplift rate of 0.02 mm/yr and a minimum shortening rate of 0.01 mm/yr are obtained. If the age of the lower (and youngest) terrace is 10 ky, as is typically seen in other locations throughout Iran, the likely range of uplift rates are 0.02-0.2 mm/yr and shortening rates 0.01-0.2 mm/yr. North of Qom city, U. Red Fmtn deposits have been folded into an asymmetric N-verging anticline known as the Alborz anticline. Seismic, well and surface data all indicate this structure has formed as a fault-bend fold above a decollement at 3 km depth which ramps to the surface along the northern limit of the fold. A balanced cross section indicates ~18% shortening (1.5 km) in a period bracketed by the Upper Red Fmtn (<18 Ma) and the Pliocene (>5.3 Ma), yielding shortening rates of 0.1-0.3 mm/yr. The right-lateral Kashan fault lies SE of the Qom region, and appears to be kinematically linked to the thrust faults around Qom, which probably represent thrust terminations. Historical earthquakes have occurred on the Kashan fault, and clear evidence for recent movement is seen in the Quaternary geomorphology. Reconstruction of the geology across the Kashan fault indicates ~45 km of total right-lateral motion, which suggests it has played a significant role in the accommodation of regional shortening. Late Cenozoic estimates of N-S shortening in the Qom region are 0.03-0.5 mm/yr. The difference in GPS velocities north and south of Qom indicates 1.1±1.9 mm/yr shortening across this region. This study suggests that Central Iran plays an important role in accommodating Arabia-Eurasia shortening over Quaternary to geological timescales. Efforts should be made to better constrain the seismic hazard posed by active faults to large populations in the Central Iran region.

Geophysical Investigation of Avon Valley, West-Central Montana, using Gravity and Seismic Reflection Profiling

NASA Astrophysics Data System (ADS)

Knatterud, L.; Mosolf, J.; Speece, M. A.; Zhou, X.

2014-12-01

The Avon Valley and adjacent mountains in west-central Montana lie within the Lewis and Clark Line, a major system of WNW-striking faults and folds that transect the more northerly structural grain of the northern Rockies and represent alternating episodes of transtensional and transpressional deformation. The northwest-trending valley has been previously interpreted as an extensional half graben filled with Tertiary sedimentary and volcanic deposits; however, little-to-no geophysical constraints on basin architecture or the thickness of Tertiary fill have been reported. A major northwest-striking fault with significant normal displacement clearly bounds the valley to the northeast, juxtaposing Tertiary sedimentary deposits against Proterozoic-Mesozoic units deformed by shortening structures and crosscut by Cretaceous granitic intrusions. Tertiary volcanic deposits unconformably overlying faulted and folded Phanerozoic-Proterozoic sequences in the eastern Garnet Range bound the valley to the southwest, but in the past no faults had been mapped along this margin. New mapping by the Montana Bureau of Mines and Geology (MBMG) has identified a system of high-angle, northwest- and northeast-striking, oblique-slip faults along the southwest border of the Avon calling into question if the valley is a half, full, or asymmetrical graben. Geophysical data has recently been acquired by Montana Tech to help define the structural architecture of the Avon Valley and the thickness of its Tertiary fill. Gravity data and a short seismic reflection profile have been collected and a preliminary interpretation of these data indicates a half graben with a series of normal faults bounding the western side of the valley. Ongoing gravity data collection throughout 2014 should refine this interpretation by better defining the bedrock-Tertiary interface at depth.

Geologic framework and evidence for neotectonism in the epicentral area of the 2011 Mineral, Virginia, earthquake

USGS Publications Warehouse

Burton, William C.; Harrison, Richard W.; Spears, David B.; Evans, Nicholas H.; Mahan, Shannon

2015-01-01

The epicenters of the main shock and associated aftershocks of the 2011 moment magnitude, Mw 5.8 Mineral, Virginia (USA), earthquake, and the updip projection of the possible fault plane that triggered the quakes, are contained in the areas of 2 adjoining 7.5′ quadrangles in the central Virginia Piedmont. These quadrangles have therefore been the focus of concentrated geologic study in the form of bedrock and surficial mapping and near-surface trenching in order to identify potential seismogenic structures. Bedrock mapping has outlined a series of northeast-southwest–trending lithologic belts that include the Ordovician Chopawamsic and Quantico Formations, the narrow neck of the Late Ordovician Ellisville pluton, and mélange zone III of the Mine Run Complex. The region was affected by at least two ductile deformational events, one in the early Paleozoic that was broadly synchronous with the intrusion of the pluton, and one later in the Paleozoic. The earlier deformation produced the Quantico synclinorium and other regional folds, and the later deformation produced faults with associated high-strain zones. Two of these faults have been trenched at their intersection along the east-dipping eastern contact of the Ellisville neck, near where the causative fault for the earthquake projects to the surface. The trenches have exposed abundant evidence of post-Paleozoic fracturing and faulting, including brecciated quartz-tourmaline veins, slickensided thrust and strike-slip faults, and clay-filled fractures. Fluvial and colluvial gravels that overlie these brittle structures have yielded optically stimulated luminescence ages ranging from ca. 27 to 10 ka. These structures are likely representative of surface features associated with Quaternary earthquakes in the Central Virginia seismic zone.

The Story of a Yakima Fold and How It Informs Late Neogene and Quaternary Backarc Deformation in the Cascadia Subduction Zone, Manastash Anticline, Washington, USA

NASA Astrophysics Data System (ADS)

Kelsey, Harvey M.; Ladinsky, Tyler C.; Staisch, Lydia; Sherrod, Brian L.; Blakely, Richard J.; Pratt, Thomas L.; Stephenson, William J.; Odum, Jack K.; Wan, Elmira

2017-10-01

The Yakima folds of central Washington, USA, are prominent anticlines that are the primary tectonic features of the backarc of the northern Cascadia subduction zone. What accounts for their topographic expression and how much strain do they accommodate and over what time period? We investigate Manastash anticline, a north vergent fault propagation fold typical of structures in the fold province. From retrodeformation of line- and area-balanced cross sections, the crust has horizontally shortened by 11% (0.8-0.9 km). The fold, and by inference all other folds in the fold province, formed no earlier than 15.6 Ma as they developed on a landscape that was reset to negligible relief following voluminous outpouring of Grande Ronde Basalt. Deformation is accommodated on two fault sets including west-northwest striking frontal thrust faults and shorter north to northeast striking faults. The frontal thrust fault system is active with late Quaternary scarps at the base of the range front. The fault-cored Manastash anticline terminates to the east at the Naneum anticline and fault; activity on the north trending Naneum structures predates emplacement of the Grande Ronde Basalt. The west trending Yakima folds and west striking thrust faults, the shorter north to northeast striking faults, and the Naneum fault together constitute the tectonic structures that accommodate deformation in the low strain rate environment in the backarc of the Cascadia Subduction Zone.

The story of a Yakima fold and how it informs Late Neogene and Quaternary backarc deformation in the Cascadia subduction zone, Manastash anticline, Washington, USA

USGS Publications Warehouse

Kelsey, Harvey M.; Ladinsky, Tyler C.; Staisch, Lydia; Sherrod, Brian; Blakely, Richard J.; Pratt, Thomas; Stephenson, William; Odum, Jackson K.; Wan, Elmira

2017-01-01

The Yakima folds of central Washington, USA, are prominent anticlines that are the primary tectonic features of the backarc of the northern Cascadia subduction zone. What accounts for their topographic expression and how much strain do they accommodate and over what time period? We investigate Manastash anticline, a north vergent fault propagation fold typical of structures in the fold province. From retrodeformation of line- and area-balanced cross sections, the crust has horizontally shortened by 11% (0.8–0.9 km). The fold, and by inference all other folds in the fold province, formed no earlier than 15.6 Ma as they developed on a landscape that was reset to negligible relief following voluminous outpouring of Grande Ronde Basalt. Deformation is accommodated on two fault sets including west-northwest striking frontal thrust faults and shorter north to northeast striking faults. The frontal thrust fault system is active with late Quaternary scarps at the base of the range front. The fault-cored Manastash anticline terminates to the east at the Naneum anticline and fault; activity on the north trending Naneum structures predates emplacement of the Grande Ronde Basalt. The west trending Yakima folds and west striking thrust faults, the shorter north to northeast striking faults, and the Naneum fault together constitute the tectonic structures that accommodate deformation in the low strain rate environment in the backarc of the Cascadia Subduction Zone.

Morphostructural evidence for Recent/active extension in Central Tanzania beyond the southern termination of the Kenya Rift.

NASA Astrophysics Data System (ADS)

Le Gall, B.; Rolet, J.; Gernigon, L.; Ebinger, C.; Gloaguen, R.

2003-04-01

The southern tip zone of the Kenya Rift on the eastern branch of the East African System is usually thought to occur in the so-called North Tanzanian Divergence. In this region, the narrow (50 km-wide) axial graben of southern Kenya splays southwards, via a major EW-trending volcanic lineament, into a 200 km-wide broad rifted zone with three separate arms of normal faulting and tilted fault blocks (Eyasi, Manyara and Pangani arms from W to E). Remote sensing analysis from Central Tanzania demonstrates that rift morphology exists over an area lying 400 km beyond the southern termination of the Kenya Rift. The most prominent rift structures are observed in the Kilombero region and consist of a 100 km-wide range of uplifted basement blocks fringed to the west by an E-facing half-graben inferred to reach depths of 6-8 km from aeromagnetic dataset. Physiographic features (fault scarps), and river drainage anomalies suggest that the present-day rift pattern in the Kilombero extensional province principally results from Recent/Neogene deformation. That assumption is also supported by the seismogenic character of a number of faults. The Kilombero half-graben is superimposed upon an earlier rift system, Karoo in age, which is totally overprinted and is only evidenced from its sedimentary infill. On the other hand, the nature and thickness of the inferred Neogene synrift section is still unknown. The Kilombero rifted zone is assumed to connect northwards into the central rift arm (Manyara) of the South Kenya Rift via a seismically active transverse fault zone that follows ductile fabrics within the Mozambican crystalline basement. The proposed rift model implies that incipient rifting propagates hroughout the cold and strong crust/lithosphere of Central Tanzania along Proterozoic (N140=B0E) basement weakness zones and earlier Karoo (NS)rift structures. A second belt of Recent-active linked fault/basins also extends further East from the Pangani rift arm to the offshore Zanzibar-Kerimbas graben system. The structural connection of the Kilombero rifted zone with the Lake Malawi rift further south is also envisaged and should imply the link of the eastern and western branchs of the East African Rift System south of the Tanzanian craton.

Correlation of clayey gouge in a surface exposure of the San Andreas fault with gouge at depth from SAFOD: Implications for the role of serpentinite in fault mechanics

USGS Publications Warehouse

Moore, Diane E.; Rymer, Michael J.

2012-01-01

Magnesium-rich clayey gouge similar to that comprising the two actively creeping strands of the San Andreas Fault in drill core from the San Andreas Fault Observatory at Depth (SAFOD) has been identified in a nearby outcrop of serpentinite within the fault zone at Nelson Creek. Each occurrence of the gouge consists of porphyroclasts of serpentinite and sedimentary rocks dispersed in a fine-grained, foliated matrix of Mg-rich smectitic clays. The clay minerals in all three gouges are interpreted to be the product of fluid-assisted, shear-enhanced reactions between quartzofeldspathic wall rocks and serpentinite that was tectonically entrained in the fault from a source in the Coast Range Ophiolite. We infer that the gouge at Nelson Creek connects to one or both of the gouge zones in the SAFOD core, and that similar gouge may occur at depths in between. The special significance of the outcrop is that it preserves the early stages of mineral reactions that are greatly advanced at depth, and it confirms the involvement of serpentinite and the Mg-rich phyllosilicate minerals that replace it in promoting creep along the central San Andreas Fault.

The 2013 Mw 6.2 Khaki-Shonbe (Iran) Earthquake: Seismic Shortening of the Zagros Sedimentary Cover

NASA Astrophysics Data System (ADS)

Elliott, J. R.; Bergman, E.; Copley, A.; Ghods, A.; Nissen, E.; Oveisi, B.; Walters, R. J.

2014-12-01

The 2013 Mw 6.2 Khaki-Shonbe earthquake occurred in the Simply Folded Belt of the Zagros Mountains, Iran. This is the largest earthquake in the Zagros since the November 1990 Mw 6.4 Furg (Hormozgan) thrust faulting event, and therefore the largest in the period for which dense InSAR ground displacements are available. It is also the biggest seismic event to have occurred in the Simply Folded Belt since the March 1977 Mw 6.7 Khurgu earthquake. This earthquake therefore potentially provides valuable insights into a range of controversies: (1) the preponderance of earthquake faulting in the crystalline basement versus the sedimentary cover and the potential importance of lithology in controlling and limiting seismic rupture; (2) the nature of surface folding and whether or not there is a one-to-one relationship between buried reverse faults and surface anticlines; and (3) the presence or absence of large pulses of aseismic slip triggered by mainshock rupture. We combine seismological solutions and aftershock relocations with satellite interferometric ground displacements and observations from the field to determine the geometry of faulting and its relationship with the structure, stratigraphy and tectonics of the Central Zagros. The earthquake rupture involved reverse slip on two along-strike southwest dipping fault segments, the rupture initiating at the northern and bottom end of the larger north-west segment. These faults verge away from the foreland and towards the high range interior, contrary to the fault geometries depicted in many structural cross-sections of the Zagros. The slip measured on the reverse segments occurred over two mutually exclusive depth ranges, 10-5 km and 4-2 km, resulting in long (16 km), narrow (7 km) rupture segments. Conversely, aftershocks are found to cluster in the depth range 8-16 km, beneath the main rupture segment. This indicates only significant reverse slip and coseismic shortening in the sedimentary cover, with the slip distribution likely to be lithologically controlled in depth by the Hormuz salt at the base of the sedimentary cover, and the Kazhdumi Formation mudrocks at upper-levels (5 km), and aftershocks constrained largely beneath the main coseismic rupture planes.

Late Pleistocene intraplate extension of the Central Anatolian Plateau, Turkey: Inferences from cosmogenic exposure dating of alluvial fan, landslide and moraine surfaces along the Ecemiş Fault Zone

NASA Astrophysics Data System (ADS)

Yildirim, Cengiz; Akif Sarikaya, Mehmet; Ciner, Attila

2016-04-01

Late Pleistocene activity of the Ecemiş Fault Zone is integrally tied to ongoing intraplate crustal deformation in the Central Anatolian Plateau. Here we document the vertical displacement, slip rate, extension rate, and geochronology of normal faults within a narrow strip along the main strand of the fault zone. The Kartal, Cevizlik and Lorut faults are normal faults that have evident surface expression within the strip. Terrestrial cosmogenic nuclide geochronology reveals that the Kartal Fault deformed a 104.2 ± 16.5 ka alluvial fan surface and the Cevizlik Fault deformed 21.9 ± 1.8 ka glacial moraine and talus fan surfaces. The Cevizlik Fault delimits mountain front of the Aladaglar and forms >1 km relief. Our topographic surveys indicate 13.1 ± 1.4 m surface breaking vertical displacements along Cevizlik Faults, respectively. Accordingly, we suggest a 0.60 ± 0.08 mm a-1 slip rate and 0.35 ± 0.05 mm a-1 extension rate for the last 21.9 ± 1.8 ka on the Cevizlik Fault. Taken together with other structural observations in the region, we believe that the Cevizlik, Kartal ve Lorut faults are an integral part of intraplate crustal deformation in Central Anatolia. They imply that intraplate structures such as the Ecemiş Fault Zone may change their mode through time; presently, the Ecemiş Fault Zone has been deformed predominantly by normal faults. The presence of steep preserved fault scarps along the Kartal, Cevizlik and Lorut faults point to surface breaking normal faulting away from the main strand and particularly signify that these structures need to be taken into account for regional seismic hazard assessments. This project is supported by The Scientific and Technological Research Council of Turkey (TUBITAK, Grant number: 112Y087).

Mean and modal ϵ in the deaggregation of probabilistic ground motion

USGS Publications Warehouse

Harmsen, Stephen C.

2001-01-01

Mean and modal ϵ exhibit a wide variation geographically for any specified PE. Modal ϵ for the 2% in 50 yr PE exceeds 2 near the most active western California faults, is less than –1 near some less active faults of the western United States (principally in the Basin and Range), and may be less than 0 in areal fault zones of the central and eastern United States (CEUS). This geographic variation is useful for comparing probabilistic ground motions with ground motions from scenario earthquakes on dominating faults, often used in seismic-resistant provisions of building codes. An interactive seismic-hazard deaggregation menu item has been added to the USGS probabilistic seismic-hazard analysis Web site, http://geohazards.cr.usgs.gov/eq/, allowing visitors to compute mean and modal distance, magnitude, and ϵ corresponding to ground motions having mean return times from 250 to 5000 yr for any site in the United States.

Elasto-plastic deformation and plate weakening due to normal faulting in the subducting plate along the Mariana Trench

NASA Astrophysics Data System (ADS)

Zhou, Z.; Lin, J.

2017-12-01

We investigated variations in the elasto-plastic deformation of the subducting plate along the Mariana Trench through an analysis of flexural bending, normal fault characteristics, and geodynamic modeling. It was observed that most of the normal faults were initiated along the outer-rise region and grew toward the trench axis with strikes that are mostly subparallel to the local trend of the trench axis. The average trench relief is more than 5 km in the southern region while only about 2 km in the northern and central regions. Fault throws were measured to be significantly greater in the southern region (maximum 320 m) than the northern and central regions (maximum 200 m). The subducting plate was modeled as an elasto-plastic slab subjected to tectonic loading along the trench axis. The "apparent" slab-pull dip angle of the subducting plate, calculated from the ratio of the inverted vertical loading versus horizontal tensional force, was significantly larger in the southern region (51-64°) than in the northern (22-35°) and central (20-34°) regions, which is consistent with the seismologically determined dip angle within the shallow part of the subducting slab. This result suggests that the differences in the plate flexure and normal faulting characteristics along the Mariana Trench might be influenced, at least in part, by significant variations in the dip angle within the shallow part of the subducting plate. Normal faults were modeled to penetrate to a maximum depth of 15, 14, and 25 km in the upper mantle for the northern, central, and southern regions, respectively, which is consistent with the depths of available relocated normal faulting earthquakes in the central region. We calculated that the average reduction of the effective elastic plate thickness Te due to normal faulting is 31% in the southern region, which is almost twice that in both the northern and central regions ( 16%). Furthermore, model results revealed that the stress reduction associated with individual normal faults could also decrease Te locally.

Late Pleistocene-Holocene Activity of the Strike-slip Xianshuihe Fault Zone, Tibetan Plateau, Inferred from Tectonic Landforms

NASA Astrophysics Data System (ADS)

Lin, A.; Yan, B.

2017-12-01

Knowledges on the activity of the strike-slip fault zones on the Tibetan Plateau have been promoted greatly by the interpretation of remote sensing images (Molnar and Tapponnier, 1975; Tapponnier and Molnar, 1977). The active strike-slip Xianshuihe-Xiaojiang Fault System (XXFS), with the geometry of an arc projecting northeastwards, plays an important role in the crustal deformation of the Tibetan Plateau caused by the continental collision between the Indian and Eurasian plates. The Xianshuihe Fault Zone (XFZ) is located in the central segment of the XXFS and extends for 370 km, with a maximum sinistral offset of 60 km since 13‒5 Ma. In this study, we investigated the tectonic landforms and slip rate along the central segment of the left-lateral strike-slip XFZ. Field investigations and analysis of ttectonic landforms show that horizontal offset has been accumulated on the topographical markers of different scales that developed since the Last Glacial Maximum (LGM). The central segment of the XFZ is composed of three major faults: Yalahe, Selaha, and Zheduotang faults showing a right-stepping echelon pattern, that is characterized by systematical offset of drainages, alluvial fans and terrace risers with typical scissoring structures, indicating a structural feature of left-lateral strike-slip fault. Based on the offset glacial morphology and radiocarbon dating ages, we estimate the Late Pleistocene-Holocene slip rate to be 10 mm/yr for the central segment of the XFZ, which is consistent with that estimated from the GPS observations and geological evidence as reported previously. Across the central segment of the XFZ, the major Selaha and Zheduotang faults participate a slip rate of 5.8 mm/yr and 3.4 mm/yr, respectively. Detailed investigations of tectonic landforms are essential for the understanding the activity of active faults. Our findings suggest that the left-lateral slipping of the XFZ partitions the deformation of eastward extrusion and northeastward shortening of the central Tibetan Plateau to accommodate the continuing penetration of the Indian plate into the Eurasian plate.

Late Quaternary faulting in the Sevier Desert driven by magmatism.

PubMed

Stahl, T; Niemi, N A

2017-03-14

Seismic hazard in continental rifts varies as a function of strain accommodation by tectonic or magmatic processes. The nature of faulting in the Sevier Desert, located in eastern Basin and Range of central Utah, and how this faulting relates to the Sevier Desert Detachment low-angle normal fault, have been debated for nearly four decades. Here, we show that the geodetic signal of extension across the eastern Sevier Desert is best explained by magma-assisted rifting associated with Plio-Pleistocene volcanism. GPS velocities from 14 continuous sites across the region are best-fit by interseismic strain accumulation on the southern Wasatch Fault at c. 3.4 mm yr -1 with a c. 0.5 mm yr -1 tensile dislocation opening in the eastern Sevier Desert. The characteristics of surface deformation from field surveys are consistent with dike-induced faulting and not with faults soling into an active detachment. Geologic extension rates of c. 0.6 mm yr -1 over the last c. 50 kyr in the eastern Sevier Desert are consistent with the rates estimated from the geodetic model. Together, these findings suggest that Plio-Pleistocene extension is not likely to have been accommodated by low-angle normal faulting on the Sevier Desert Detachment and is instead accomplished by strain localization in a zone of narrow, magma-assisted rifting.

Late Quaternary faulting in the Sevier Desert driven by magmatism

PubMed Central

Stahl, T.; Niemi, N. A.

2017-01-01

Seismic hazard in continental rifts varies as a function of strain accommodation by tectonic or magmatic processes. The nature of faulting in the Sevier Desert, located in eastern Basin and Range of central Utah, and how this faulting relates to the Sevier Desert Detachment low-angle normal fault, have been debated for nearly four decades. Here, we show that the geodetic signal of extension across the eastern Sevier Desert is best explained by magma-assisted rifting associated with Plio-Pleistocene volcanism. GPS velocities from 14 continuous sites across the region are best-fit by interseismic strain accumulation on the southern Wasatch Fault at c. 3.4 mm yr−1 with a c. 0.5 mm yr−1 tensile dislocation opening in the eastern Sevier Desert. The characteristics of surface deformation from field surveys are consistent with dike-induced faulting and not with faults soling into an active detachment. Geologic extension rates of c. 0.6 mm yr−1 over the last c. 50 kyr in the eastern Sevier Desert are consistent with the rates estimated from the geodetic model. Together, these findings suggest that Plio-Pleistocene extension is not likely to have been accommodated by low-angle normal faulting on the Sevier Desert Detachment and is instead accomplished by strain localization in a zone of narrow, magma-assisted rifting. PMID:28290529

Estimation of recurrence interval of large earthquakes on the central Longmen Shan fault zone based on seismic moment accumulation/release model.

PubMed

Ren, Junjie; Zhang, Shimin

2013-01-01

Recurrence interval of large earthquake on an active fault zone is an important parameter in assessing seismic hazard. The 2008 Wenchuan earthquake (Mw 7.9) occurred on the central Longmen Shan fault zone and ruptured the Yingxiu-Beichuan fault (YBF) and the Guanxian-Jiangyou fault (GJF). However, there is a considerable discrepancy among recurrence intervals of large earthquake in preseismic and postseismic estimates based on slip rate and paleoseismologic results. Post-seismic trenches showed that the central Longmen Shan fault zone probably undertakes an event similar to the 2008 quake, suggesting a characteristic earthquake model. In this paper, we use the published seismogenic model of the 2008 earthquake based on Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR) data and construct a characteristic seismic moment accumulation/release model to estimate recurrence interval of large earthquakes on the central Longmen Shan fault zone. Our results show that the seismogenic zone accommodates a moment rate of (2.7 ± 0.3) × 10¹⁷ N m/yr, and a recurrence interval of 3900 ± 400 yrs is necessary for accumulation of strain energy equivalent to the 2008 earthquake. This study provides a preferred interval estimation of large earthquakes for seismic hazard analysis in the Longmen Shan region.

Estimation of Recurrence Interval of Large Earthquakes on the Central Longmen Shan Fault Zone Based on Seismic Moment Accumulation/Release Model

PubMed Central

Zhang, Shimin

2013-01-01

Recurrence interval of large earthquake on an active fault zone is an important parameter in assessing seismic hazard. The 2008 Wenchuan earthquake (Mw 7.9) occurred on the central Longmen Shan fault zone and ruptured the Yingxiu-Beichuan fault (YBF) and the Guanxian-Jiangyou fault (GJF). However, there is a considerable discrepancy among recurrence intervals of large earthquake in preseismic and postseismic estimates based on slip rate and paleoseismologic results. Post-seismic trenches showed that the central Longmen Shan fault zone probably undertakes an event similar to the 2008 quake, suggesting a characteristic earthquake model. In this paper, we use the published seismogenic model of the 2008 earthquake based on Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR) data and construct a characteristic seismic moment accumulation/release model to estimate recurrence interval of large earthquakes on the central Longmen Shan fault zone. Our results show that the seismogenic zone accommodates a moment rate of (2.7 ± 0.3) × 1017 N m/yr, and a recurrence interval of 3900 ± 400 yrs is necessary for accumulation of strain energy equivalent to the 2008 earthquake. This study provides a preferred interval estimation of large earthquakes for seismic hazard analysis in the Longmen Shan region. PMID:23878524

Synthesis of Creep Measurements from Strainmeters and Creepmeters along the San Andreas Fault: Implications for Seismic vs. Aseismic Partitioning

NASA Astrophysics Data System (ADS)

Mencin, D.; Gottlieb, M. H.; Hodgkinson, K. M.; Bilham, R. G.; Mattioli, G. S.; Johnson, W.; Van Boskirk, E.; Meertens, C. M.

2015-12-01

Strainmeters and creepmeters have been operated along the San Andreas Fault, observing creep events for decades. In particular, the EarthScope Plate Boundary Observatory (PBO) has added a significant number of borehole strainmeters along the San Andreas Fault (SAF) over the last decade. The geodetic data cover a significant temporal portion of the inferred earthquake cycle along this portion of the SAF. Creepmeters measure the surface displacement over time (creep) with short apertures and have the ability to capture slow slip, coseismic rupture, and afterslip. Modern creepmeters deployed by the authors have a resolution of 5 µm over a range of 10 mm and a dynamic sensor with a resolution 25 µm over a range 2.2 m. Borehole strainmeters measure local deformation some distance from the fault with a broader aperture. Borehole tensor strainmeters principally deployed as part of the PBO, measure the horizontal strain tensor at a depth of 100-200 m with a resolution of 10-11 strain and are located 4 - 10 km from the fault with the ability to image a 1 mm creep event acting on an area of ~500 m2 from over 4 km away (fault perpendicular). A single borehole tensor strainmeter is capable of providing broad constraints on the creep event asperity size, location, direction and depth of a single creep event. The synthesis of these data from all the available geodetic instruments proximal to the SAF presents a unique opportunity to constrain the partitioning between aseismic and seismic slip on the central SAF. We show that simple elastic half-space models allow us to loosely constrain the location and depth of any individual creep event on the fault, even with a single instrument, and to image the accumulation of creep with time.

Rupture of the Pitáycachi Fault in the 1887 Mw 7.5 Sonora, Mexico earthquake (southern Basin-and-Range Province): Rupture kinematics and epicenter inferred from rupture branching patterns

NASA Astrophysics Data System (ADS)

Suter, Max

2015-01-01

During the 3 May 1887 Mw 7.5 Sonora earthquake (surface rupture end-to-end length: 101.8 km), an array of three north-south striking Basin-and-Range Province faults (from north to south Pitáycachi, Teras, and Otates) slipped sequentially along the western margin of the Sierra Madre Occidental Plateau. This detailed field survey of the 1887 earthquake rupture zone along the Pitáycachi fault includes mapping the rupture scarp and measurements of surface deformation. The surface rupture has an endpoint-to-endpoint length of ≥41.0 km, dips 70°W, and is characterized by normal left-lateral extension. The maximum surface offset is 487 cm and the mean offset 260 cm. The rupture trace shows a complex pattern of second-order segmentation. However, this segmentation is not expressed in the 1887 along-rupture surface offset profile, which indicates that the secondary segments are linked at depth into a single coherent fault surface. The Pitáycachi surface rupture shows a well-developed bipolar branching pattern suggesting that the rupture originated in its central part, where the polarity of the rupture bifurcations changes. Most likely the rupture first propagated bilaterally along the Pitáycachi fault. The southern rupture front likely jumped across a step over to the Teras fault and from there across a major relay zone to the Otates fault. Branching probably resulted from the lateral propagation of the rupture after breaching the seismogenic part of the crust, given that the much shorter ruptures of the Otates and Teras segments did not develop branches.

Morphometric study of the Habo dome, Kachchh, Gujarat, India: implications on neotectonic activity

NASA Astrophysics Data System (ADS)

Bhattacharjee, N.; Mohanty, S. P.

2017-12-01

The Kachchh Basin of western India was developed during the separation of the Indian plate from the Gondwanaland in Mesozoic. Series of E-W striking master faults were generated during this extensional phase. The collision of the Indian and Eurasian plates in Eocene time resulted in the change of stress regime to a compressional setting when the built-up stress developed NNW-SSE to NNE-SSW striking transverse faults and reactivated the earlier E-W master faults. The present work was carried out in the Habo dome, located in the central part of the Kachchh Basin, to analyse the morphometric features such as the bifurcation ratio, circulation ratio, drainage texture, asymmetric factor, hypsometric indices and mountain front sinuosity of selected sub-watersheds of the area to understand the effects of fault reactivation and neotectonic activities on the geometry of the dome. Shuttle Radar Topographic Mission (SRTM) Digital Elevation Model (DEM) data were used to extract drainage network for morphometric analysis of the Kaswati, Khari, and Pur river basins. The study area is elliptical in outline with the long axis trending approximately E-W. The evolution of this domal structure is interpreted to be the result of fault-bound nature of the block. The northern slope of the dome is bound by the Kachchh Mainland Fault and the eastern and western boundaries are marked by transverse faults. The undulating topography was developed by differential movements along several transverse faults striking NW-SE, N-S, and NE-SW. The earlier interpretation of laccolith intrusion into the sedimentary rocks is not supported by the data analysis and field mapping. Stress propagations from the Himalayan range in the northeast and Sulaiman range in the northwest are identified to be the causative factor for historical seismicity and drainage anomalies in the area. Keywords: Basin morphometry, Geographical Information System, Lineament patterns, Kachchh basin, Neotectonics, Fault reactivation

Geology of the Pavana geothermal area, Departamento de Choluteca, Honduras, Central America: Field report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eppler, D.B.; Heiken, G.; Wohletz, K.

The Pavana geothermal area is located in southern Honduras near the Gulf of Fonseca. This region is underlain by late Tertiary volcanic rocks. Within ranges near the geothermal manifestations, the rock sequences is characterized by intermediate to mafic laharic breccias and lavas overlain by silicic tuffs and lavas, which are in turn overlain by intermediate to mafic breccias, lavas, and tuffs. The nearest Quaternary volcanoes are about 40 km to the southwest, where the chain of active Central American volcanoes crosses the mouth of the Gulf of Fonseca. Structure of the Pavana area is dominated by generally northwest-trending, southwest-dipping normalmore » faults. This structure is topographically expressed as northwest-trending escarpments that bound blocks of bedrock separated by asymmetric valleys that contain thin alluvial deposits. Thermal waters apparently issue from normal faults and are interpreted as having been heated during deep circulation along fault zones within a regional environment of elevated heat flow. Natural outflow from the main thermal area is about 3000 l/min of 60/sup 0/C water. Geothermometry of the thermal waters suggests a reservoir base temperature of about 150/sup 0/C.« less

Astypalaea Linea: A Large-Scale Strike-Slip Fault on Europa

NASA Astrophysics Data System (ADS)

Tufts, B. Randall; Greenberg, Richard; Hoppa, Gregory; Geissler, Paul

1999-09-01

Astypalaea Linea is an 810-km strike-slip fault, located near the south pole of Europa. In length, it rivals the San Andreas Fault in California, and it is the largest strike-slip fault yet known on Europa. The fault was discovered using Voyager 2 images, based upon the presence of familiar strike-slip features including linearity, pull-aparts, and possible braids, and upon the offset of multiple piercing points. Fault displacement is 42 km, right-lateral, in the southern and central parts and probably throughout. Pull-aparts present along the fault trace probably are gaps in the lithosphere bounded by vertical cracks, and which opened due to fault motion and filled with material from below. Crosscutting relationships suggest the fault to be of intermediate relative age. The fault may have initiated as a crack due to tension from combined diurnal tides and nonsynchronous rotation, according to the tectonic model of R. Greenberg et al. (1998a, Icarus135, 64-78). Under the influence of varying diurnal tides, strike-slip offset may have occurred through a process called “walking,” which depends upon an inelastic lithospheric response to displacement. Alternatively, fault displacement may have been driven by currents in the theorized Europan ocean, which may have created simple shear structures such as braids. The discovery of Astypalaea Linea extends the geographical range of lateral motion on Europa. Such motion requires the presence of a decoupling zone of ductile ice or liquid water, a sufficiently rigid lithosphere, and a mechanism to consume surface area.

Three-dimensional upper crustal velocity structure beneath San Francisco Peninsula, California

USGS Publications Warehouse

Parsons, T.; Zoback, M.L.

1997-01-01

This paper presents new seismic data from, and crustal models of the San Francisco Peninsula. In much of central California the San Andreas fault juxtaposes the Cretaceous granitic Salinian terrane on its west and the Late Mesozoic/Early Tertiary Franciscan Complex on its east. On San Francisco Peninsula, however, the present-day San Andreas fault is completely within a Franciscan terrane, and the Pilarcitos fault, located southwest of the San Andreas, marks the Salinian-Franciscan boundary. This circumstance has evoked two different explanations: either the Pilarcitos is a thrust fault that has pushed Franciscan rocks over Salinian rocks or the Pilarcitos is a transform fault that has accommodated significant right-lateral slip. In an effort to better resolve the subsurface structure of the peninsula faults, we established a temporary network of 31 seismographs arrayed across the San Andreas fault and the subparallel Pilarcitos fault at ???1-2 km spacings. These instruments were deployed during the first 6 months of 1995 and recorded local earthquakes, air gun sources set off in San Francisco Bay, and explosive sources. Travel times from these sources were used to augment earthquake arrival times recorded by the Northern California Seismic Network and were inverted for three-dimensional velocity structure. Results show lateral velocity changes at depth (???0.5-7 km) that correlate with downward vertical projections of the surface traces of the San Andreas and Pilarcitos faults. We thus interpret the faults as high-angle to vertical features (constrained to a 70??-110?? dip range). From this we conclude that the Pilarcitos fault is probably an important strike-slip fault that accommodated much of the right-lateral plate boundary strain on the peninsula prior to the initiation of the modern-day San Andreas fault in this region sometime after about 3.0 m.y. ago.

Assessment of Late Quaternary strain partitioning in the Afar Triple Junction: Dobe and Hanle grabens, Ethiopia and Djibouti

NASA Astrophysics Data System (ADS)

Polun, S. G.; Stockman, M. B.; Hickcox, K.; Horrell, D.; Tesfaye, S.; Gomez, F. G.

2015-12-01

As the only subaerial exposure of a ridge - ridge - ridge triple junction, the Afar region of Ethiopia and Djibouti offers a rare opportunity to assess strain partitioning within this type of triple junction. Here, the plate boundaries do not link discretely, but rather the East African rift meets the Red Sea and Gulf of Aden rifts in a zone of diffuse normal faulting characterized by a lack of magmatic activity, referred to as the central Afar. An initial assessment of Late Quaternary strain partitioning is based on faulted landforms in the Dobe - Hanle graben system in Ethiopia and Djibouti. These two extensional basins are connected by an imbricated accommodation zone. Several fault scarps occur within terraces formed during the last highstand of Lake Dobe, around 5 ka - they provide a means of calibrating a numerical model of fault scarp degradation. Additional timing constraints will be provided by pending exposure ages. The spreading rates of both grabens are equivalent, however in Dobe graben, extension is partitioned 2:1 between northern, south dipping faults and the southern, north dipping fault. Extension in Hanle graben is primarily focused on the north dipping Hanle fault. On the north margin of Dobe graben, the boundary fault bifurcates, where the basin-bordering fault displays a significantly higher modeled uplift rate than the more distal fault, suggesting a basinward propagation of faulting. On the southern Dobe fault, surveyed fault scarps have ages ranging from 30 - 5 ka with uplift rates of 0.71, 0.47, and 0.68 mm/yr, suggesting no secular variation in slip rates from the late Plestocene through the Holocene. These rates are converted into horizontal stretching estimates, which are compared with regional strain estimated from velocities of relatively sparse GPS data.

Physical and Transport Property Variations Within Carbonate-Bearing Fault Zones: Insights From the Monte Maggio Fault (Central Italy)

NASA Astrophysics Data System (ADS)

Trippetta, F.; Carpenter, B. M.; Mollo, S.; Scuderi, M. M.; Scarlato, P.; Collettini, C.

2017-11-01

The physical characterization of carbonate-bearing normal faults is fundamental for resource development and seismic hazard. Here we report laboratory measurements of density, porosity, Vp, Vs, elastic moduli, and permeability for a range of effective confining pressures (0.1-100 MPa), conducted on samples representing different structural domains of a carbonate-bearing fault. We find a reduction in porosity from the fault breccia (11.7% total and 6.2% connected) to the main fault plane (9% total and 3.5% connected), with both domains showing higher porosity compared to the protolith (6.8% total and 1.1% connected). With increasing confining pressure, P wave velocity evolves from 4.5 to 5.9 km/s in the fault breccia, is constant at 5.9 km/s approaching the fault plane and is low (4.9 km/s) in clay-rich fault domains. We find that while the fault breccia shows pressure sensitive behavior (a reduction in permeability from 2 × 10-16 to 2 × 10-17 m2), the cemented cataclasite close to the fault plane is characterized by pressure-independent behavior (permeability 4 × 10-17 m2). Our results indicate that the deformation processes occurring within the different fault structural domains influence the physical and transport properties of the fault zone. In situ Vp profiles match well the laboratory measurements demonstrating that laboratory data are valuable for implications at larger scale. Combining the experimental values of elastic moduli and frictional properties it results that at shallow crustal levels, M ≤ 1 earthquakes are less favored, in agreement with earthquake-depth distribution during the L'Aquila 2009 seismic sequence that occurred on carbonates.

Thermochronometrically constrained anatomy and evolution of a Miocene extensional accommodation zone and tilt domain boundary: The southern Wassuk Range, Nevada

NASA Astrophysics Data System (ADS)

Gorynski, Kyle E.; Stockli, Daniel F.; Douglas Walker, J.

2013-06-01

(AHe) and Zircon (ZHe) (U-Th)/He thermochronometric data from the southern Wassuk Range (WR) coupled with 40Ar/39Ar age data from the overlying tilted Tertiary section are used to constrain the thermal evolution of an extensional accommodation zone and tilt-domain boundary. AHe and ZHe data record two episodes of rapid cooling related to the tectonic exhumation of the WR fault block beginning at ~15 and ~4 Ma. Extension was accommodated through fault-block rotation and variably tilted the southern WR to the west from ~60°-70° in the central WR to ~15°-35° in the southernmost WR and Pine Grove Hills, and minimal tilting in the Anchorite Hills and along the Mina Deflection to the south. Middle Miocene geothermal gradient estimates record heating immediately prior to large-magnitude extension that was likely coeval with the extrusion of the Lincoln Flat andesite at ~14.8 Ma. Geothermal gradients increase from ~19° ± 4°C/km to ≥ 65° ± 20°C/km toward the Mina Deflection, suggesting that it was the focus of Middle Miocene arc magmatism in the upper crust. The decreasing thickness of tilt blocks toward the south resulted from a shallowing brittle/ductile transition zone. Postmagmatic Middle Miocene extension and fault-block advection were focused in the northern and central WR and coincidentally moderated the large lateral thermal gradient within the uppermost crust.

The influence of upper-crust lithology on topographic development in the central Coast Ranges of California

USGS Publications Warehouse

Garcia, A.F.; Mahan, S.A.

2012-01-01

A fundamental geological tenet is that as landscapes evolve over graded to geologic time, geologic structures control patterns of topographic distribution in mountainous areas such that terrain underlain by competent rock will be higher than terrain underlain by incompetent rock. This paper shows that in active orogens where markedly weak and markedly strong rocks are juxtaposed along contacts that parallel regional structures, relatively high topography can form where strain is localized in the weak rock. Such a relationship is illustrated by the topography of the central Coast Ranges between the Pacific coastline and the San Andreas fault zone (SAFZ), and along the length of the Gabilan Mesa (the "Gabilan Mesa segment" of the central Coast Ranges). Within the Gabilan Mesa segment, the granitic upper crust of the Salinian terrane is in contact with the accretionary-prism m??lange upper crust of the Nacimiento terrane along the inactive Nacimiento fault zone. A prominent topographic lineament is present along most of this lithologic boundary, approximately 50 to 65. km southwest of the SAFZ, with the higher topography formed in the m??lange on the southwest side of the Nacimiento fault. This paper investigates factors influencing the pattern of topographic development in the Gabilan Mesa segment of the central Coast Ranges by correlating shortening magnitude with the upper-crust compositions of the Salinian and Nacimiento terranes. The fluvial geomorphology of two valleys in the Gabilan Mesa, which is within the Salinian terrane, and alluvial geochronology based on optically-stimulated luminescence (OSL) age estimates, reveal that the magnitude of shortening accommodated by down-to-the-southwest tilting of the mesa since 400ka is less than 1 to 2m. Our results, combined with those of previous studies, indicate that at least 63% to 78% of late-Cenozoic, northeast-southwest directed, upper-crustal shortening across the Gabilan Mesa segment has been accommodated within the Nacimiento terrane. This is significant because perpendicular to orogenic strike the Nacimiento terrane constitutes less than 1/4 of the distance between the coast and the SAFZ, and the other 3/4 (or greater) of the distance between the coast and the SAFZ is underlain by the granitic upper crust of the Salinian terrane. We propose that strain and mountain building are localized within the Nacimiento terrane because it consists predominantly of the relatively weak Franciscan Complex m??lange, and because the upper crust of the Salinian terrane is composed of relatively strong granitic rocks. Our hypothesis is supported by the distribution of post-seismic surface uplift associated with the 2003, 6.5M W San Simeon earthquake, which mimics the topography of the southwestern part of the Gabilan Mesa segment of the central Coast Ranges. ?? 2011 Elsevier B.V.

Seasonal water storage, stress modulation and California seismicity

NASA Astrophysics Data System (ADS)

Johnson, C. W.; Burgmann, R.; Fu, Y.

2017-12-01

Establishing what controls the timing of earthquakes is fundamental to understanding the nature of the earthquake cycle and critical to determining time-dependent earthquake hazard. Seasonal loading provides a natural laboratory to explore the crustal response to a quantifiable transient force. In California, the accumulation of winter snowpack in the Sierra Nevada, surface water in lakes and reservoirs, and groundwater in sedimentary basins follow the annual cycle of wet winters and dry summers. The surface loads resulting from the seasonal changes in water storage produce elastic deformation of the Earth's crust. We used 9 years of global positioning system (GPS) vertical deformation time series to constrain models of monthly hydrospheric loading and the resulting stress changes on fault planes of small earthquakes. Previous studies posit that temperature, atmospheric pressure, or hydrologic changes may strain the lithosphere and promote additional earthquakes above background levels. Depending on fault geometry, the addition or removal of water increases the Coulomb failure stress. The largest stress amplitudes are occurring on dipping reverse faults in the Coast Ranges and along the eastern Sierra Nevada range front. We analyze 9 years of M≥2.0 earthquakes with known focal mechanisms in northern and central California to resolve fault-normal and fault-shear stresses for the focal geometry. Our results reveal 10% more earthquakes occurring during slip-encouraging fault-shear stress conditions and suggest that earthquake populations are modulated at periods of natural loading cycles, which promote failure by stress changes on the order of 1-5 kPa. We infer that California seismicity rates are modestly modulated by natural hydrological loading cycles.

Seismic reflection images of the central California coast ranges and the tremor region of the San-Andreas-Fault system near Cholame

NASA Astrophysics Data System (ADS)

Gutjahr, Stine; Buske, Stefan

2010-05-01

The SJ-6 seismic reflection profile was acquired in 1981 over a distance of about 180 km from Morro Bay to the Sierra Nevada foothills in South Central California. The profile runs across several prominent fault systems, e.g. the Riconada Fault (RF) in the western part as well as the San Andreas Fault (SAF) in its central part. The latter includes the region of increased tremor activity near Cholame, as reported recently by several authors. We have recorrelated the original field data to 26 seconds two-way traveltime which allows us to image the crust and uppermost mantle down to approximately 40 km depth. A 3D tomographic velocity model derived from local earthquake data (Thurber et al., 2006) was used and Kirchhoff prestack depth migration as well as Fresnel-Volume-Migration were applied to the data set. Both imaging techniques were implemented in 3D by taking into account the true shot and receiver locations. The imaged subsurface volume itself was divided into three separate parts to correctly account for the significant kink in the profile line near the SAF. The most prominent features in the resulting images are areas of high reflectivity down to 30 km depth in particular in the central western part of the profile corresponding to the Salinian Block between the RF and the SAF. In the southwestern part strong reflectors can be identified that are dipping slightly to the northeast at depths of around 15-25 km. The eastern part consists of west dipping sediments at depths of 2-10 km that form a syncline structure in the west of the eastern part. The resulting images are compared to existing interpretations (Trehu and Wheeler, 1987; Wentworth and Zoback, 1989; Bloch et al., 1993) and discussed in the frame of the suggested tremor locations in that area.

Fracture zone drilling through Atotsugawa fault in central Japan - geological and geophysical structure -

NASA Astrophysics Data System (ADS)

Omura, K.; Yamashita, F.; Yamada, R.; Matsuda, T.; Fukuyama, E.; Kubo, A.; Takai, K.; Ikeda, R.; Mizuochi, Y.

2004-12-01

Drilling is an effective method to investigate the structure and physical state in and around the active fault zone, such as, stress and strength distribution, geological structure and materials properties. In particular, the structure in the fault zone is important to understand where and how the stress accumulates during the earthquake cycle. In previous studies, we did integrate investigation on active faults in central Japan by drilling and geophysical prospecting. Those faults are estimated to be at different stage in the earthquake cycle, i.e., Nojima fault which appeared on the surface by the 1995 Great Kobe earthquake (M=7.2), the Neodani fault which appeared by the 1891 Nobi earth-quake (M=8.0), the Atera fault, of which some parts have seemed to be dislocated by the 1586 Tensyo earthquake (M=7.9), and Gofukuji Fault that is considered to have activated about 1200 years ago. Each faults showed characteristic features of fracture zone structure according to their geological and geophysical situations. In a present study, we did core recovery and down hole measurements at the Atotsugawa fault, central Japan, that is considered to have activated at 1858 Hida earthquake (M=7.0). The Atotsugawa fault is characterized by active seismicity along the fault. But, at the same time, the shallow region in the central segment of the fault seems to have low seismicity. The high seismicity segment and low seismicity segments may have different mechanical, physical and material properties. A 350m depth borehole was drilled vertically beside the surface trace of the fault in the low seismicity segment. Recovered cores were overall heavily fractured and altered rocks. In the cores, we observed many shear planes holding fault gouge. Logging data showed that the apparent resistance was about 100 - 600 ohm-m, density was about 2.0 - 2.5g/cm3, P wave velocity was approximately 3.0 - 4.0 km/sec, neutron porosity was 20 - 40 %. Results of physical logging show features of fault fracture zone that were the same as the fault fracture zones of other active faults that we have drilled previously. By the BHTV logging, we detected many fractures of which the strikes are not only parallel to the fault trace bur also oblique to the fault trace. The observations of cores and logging data indicate that the borehole passed in the fracture zone down to the bottom, and that the fracture zone has complicate internal structure including foliation not parallel to the fault trace. The core samples are significant for further investigation on material properties in the fracture zone. And we need data of geophysical prospecting to infer the deeper structure of the fracture zone.

Deformation rates across the San Andreas Fault system, central California determined by geology and geodesy

NASA Astrophysics Data System (ADS)

Titus, Sarah J.

The San Andreas fault system is a transpressional plate boundary characterized by sub-parallel dextral strike-slip faults separating internally deformed crustal blocks in central California. Both geodetic and geologic tools were used to understand the short- and long-term partitioning of deformation in both the crust and the lithospheric mantle across the plate boundary system. GPS data indicate that the short-term discrete deformation rate is ˜28 mm/yr for the central creeping segment of the San Andreas fault and increases to 33 mm/yr at +/-35 km from the fault. This gradient in deformation rates is interpreted to reflect elastic locking of the creeping segment at depth, distributed off-fault deformation, or some combination of these two mechanisms. These short-term fault-parallel deformation rates are slower than the expected geologic slip rate and the relative plate motion rate. Structural analysis of folds and transpressional kinematic modeling were used to quantify long-term distributed deformation adjacent to the Rinconada fault. Folding accommodates approximately 5 km of wrench deformation, which translates to a deformation rate of ˜1 mm/yr since the start of the Pliocene. Integration with discrete offset on the Rinconada fault indicates that this portion of the San Andreas fault system is approximately 80% strike-slip partitioned. This kinematic fold model can be applied to the entire San Andreas fault system and may explain some of the across-fault gradient in deformation rates recorded by the geodetic data. Petrologic examination of mantle xenoliths from the Coyote Lake basalt near the Calaveras fault was used to link crustal plate boundary deformation at the surface with models for the accommodation of deformation in the lithospheric mantle. Seismic anisotropy calculations based on xenolith petrofabrics suggest that an anisotropic mantle layer thickness of 35-85 km is required to explain the observed shear wave splitting delay times in central California. The available data are most consistent with models for a broad zone of distributed deformation in the lithospheric mantle.

Active Tectonics Around Almaty and along the Zailisky Alatau Rangefront

NASA Astrophysics Data System (ADS)

Grützner, C.; Walker, R. T.; Abdrakhmatov, K. E.; Mukambaev, A.; Elliott, A. J.; Elliott, J. R.

2017-10-01

The Zailisky Alatau is a >250 km long mountain range in Southern Kazakhstan. Its northern rangefront around the major city of Almaty has more than 4 km topographic relief, yet in contrast to other large mountain fronts in the Tien Shan, little is known about its Late Quaternary tectonic activity despite several destructive earthquakes in the historical record. We analyze the tectonic geomorphology of the rangefront fault using field observations, differential GPS measurements of fault scarps, historical and recent satellite imagery, meter-scale topography derived from stereo satellite images, and decimeter-scale elevation models from unmanned aerial vehicle surveys. Fault scarps ranging in height from 2 m to >20 m in alluvial fans indicate that surface rupturing earthquakes occurred along the rangefront fault since the Last Glacial Maximum. Minimum estimated magnitudes for those earthquakes are M6.8-7. Radiocarbon dating results from charcoal layers in uplifted river terraces indicate a Holocene slip rate of 1.2-2.2 mm/a. We find additional evidence for active tectonic deformation all along the Almaty rangefront, basinward in the Kazakh platform, and in the interior of the Zailisky mountain range. Our data indicate that the seismic hazard faced by Almaty comes from a variety of sources, and we emphasize the problems related to urban growth into the loess-covered foothills and secondary earthquake effects. With our structural and geochronologic framework, we present a schematic evolution of the Almaty rangefront that may be applicable to similar settings of tectonic shortening in the mountain ranges of Central Asia.

Deep reaching versus vertically restricted Quaternary normal faults: Implications on seismic potential assessment in tectonically active regions: Lessons from the middle Aterno valley fault system, central Italy

NASA Astrophysics Data System (ADS)

Falcucci, E.; Gori, S.; Moro, M.; Fubelli, G.; Saroli, M.; Chiarabba, C.; Galadini, F.

2015-05-01

We investigate the Middle Aterno Valley fault system (MAVF), a poorly investigated seismic gap in the central Apennines, adjacent to the 2009 L'Aquila earthquake epicentral area. Geological and paleoseismological analyses revealed that the MAVF evolved through hanging wall splay nucleation, its main segment moving at 0.23-0.34 mm/year since the Middle Pleistocene; the penultimate activation event occurred between 5388-5310 B.C. and 1934-1744 B.C., the last event after 2036-1768 B.C. and just before 1st-2nd century AD. These data define hard linkage (sensu Walsh and Watterson, 1991; Peacock et al., 2000; Walsh et al., 2003, and references therein) with the contiguous Subequana Valley fault segment, able to rupture in large magnitude earthquakes (up to 6.8), that did not rupture since about two millennia. By the joint analysis of geological observations and seismological data acquired during to the 2009 seismic sequence, we derive a picture of the complex structural framework of the area comprised between the MAVF, the Paganica fault (the 2009 earthquake causative fault) and the Gran Sasso Range. This sector is affected by a dense array of few-km long, closely and regularly spaced Quaternary normal fault strands, that are considered as branches of the MAVF northern segment. Our analysis reveals that these structures are downdip confined by a decollement represented by to the presently inactive thrust sheet above the Gran Sasso front limiting their seismogenic potential. Our study highlights the advantage of combining Quaternary geological field analysis with high resolution seismological data to fully unravel the structural setting of regions where subsequent tectonic phases took place and where structural interference plays a key role in influencing the seismotectonic context; this has also inevitably implications for accurately assessing seismic hazard of such structurally complex regions.

Upper crustal structure from the Santa Monica Mountains to the Sierra Nevada, Southern California: Tomographic results from the Los Angeles Regional Seismic Experiment, Phase II (LARSE II)

USGS Publications Warehouse

Lutter, W.J.; Fuis, G.S.; Ryberg, T.; Okaya, D.A.; Clayton, R.W.; Davis, P.M.; Prodehl, C.; Murphy, J.M.; Langenheim, V.E.; Benthien, M.L.; Godfrey, N.J.; Christensen, N.I.; Thygesen, K.; Thurber, C.H.; Simila, G.; Keller, Gordon R.

2004-01-01

In 1999, the U.S. Geological Survey and the Southern California Earthquake Center (SCEC) collected refraction and low-fold reflection data along a 150-km-long corridor extending from the Santa Monica Mountains northward to the Sierra Nevada. This profile was part of the second phase of the Los Angeles Region Seismic Experiment (LARSE II). Chief imaging targets included sedimentary basins beneath the San Fernando and Santa Clarita Valleys and the deep structure of major faults along the transect, including causative faults for the 1971 M 6.7 San Fernando and 1994 M 6.7 Northridge earthquakes, the San Gabriel Fault, and the San Andreas Fault. Tomographic modeling of first arrivals using the methods of Hole (1992) and Lutter et al. (1999) produces velocity models that are similar to each other and are well resolved to depths of 5-7.5 km. These models, together with oil-test well data and independent forward modeling of LARSE II refraction data, suggest that regions of relatively low velocity and high velocity gradient in the San Fernando Valley and the northern Santa Clarita Valley (north of the San Gabriel Fault) correspond to Cenozoic sedimentary basin fill and reach maximum depths along the profile of ???4.3 km and >3 km , respectively. The Antelope Valley, within the western Mojave Desert, is also underlain by low-velocity, high-gradient sedimentary fill to an interpreted maximum depth of ???2.4 km. Below depths of ???2 km, velocities of basement rocks in the Santa Monica Mountains and the central Transverse Ranges vary between 5.5 and 6.0 km/sec, but in the Mojave Desert, basement rocks vary in velocity between 5.25 and 6.25 km/sec. The San Andreas Fault separates differing velocity structures of the central Transverse Ranges and Mojave Desert. A weak low-velocity zone is centered approximately on the north-dipping aftershock zone of the 1971 San Fernando earthquake and possibly along the deep projection of the San Gabriel Fault. Modeling of gravity data, using densities inferred from the velocity model, indicates that different velocity-density relationships hold for both sedimentary and basement rocks as one crosses the San Andreas Fault. The LARSE II velocity model can now be used to improve the SCEC Community Velocity Model, which is used to calculate seismic amplitudes for large scenario earthquakes.

Effect of time dependence on probabilistic seismic-hazard maps and deaggregation for the central Apennines, Italy

USGS Publications Warehouse

Akinci, A.; Galadini, F.; Pantosti, D.; Petersen, M.; Malagnini, L.; Perkins, D.

2009-01-01

We produce probabilistic seismic-hazard assessments for the central Apennines, Italy, using time-dependent models that are characterized using a Brownian passage time recurrence model. Using aperiodicity parameters, ?? of 0.3, 0.5, and 0.7, we examine the sensitivity of the probabilistic ground motion and its deaggregation to these parameters. For the seismic source model we incorporate both smoothed historical seismicity over the area and geological information on faults. We use the maximum magnitude model for the fault sources together with a uniform probability of rupture along the fault (floating fault model) to model fictitious faults to account for earthquakes that cannot be correlated with known geologic structural segmentation.

Sandstone-filled normal faults: A case study from central California

NASA Astrophysics Data System (ADS)

Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

2018-05-01

Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

A GPS Modeling Study of Earthquakes and Deformation in Northern Central America and along the Middle America Trench: 1999 to 2017

NASA Astrophysics Data System (ADS)

Ellis, Andria P.

Northern Central America is a tectonically complicated region prone to hazardous earthquakes due to the confluence of the Motagua-Polochic fault zone with the Middle America trench and strike-slip faults in the Central America volcanic arc. These three major fault zones converge at the western end of the Caribbean plate where the Cocos plate subducts under the North America and Caribbean plates. Literature from the 1970s and 1980s focused on whether a discrete North America-Caribbean-Cocos plate triple junction existed, and how the relative motions of the upper North America and Caribbean plates were accommodated. The discovery of a fourth major crustal block, the Central America forearc sliver, from seismic and geodetic observations made a three-plate triple junction geometrically impossible and introduced a new set of questions related to how deformation of the upper plate accommodates relative movements between the Caribbean plate, North America plate, and Central America forearc sliver where they intersect in the upper plate. My dissertation uses GPS and numerical modeling to measure and quantify earthquake transients and crustal deformation related to fault interactions in northern Central America and consists of three related chapters. The first chapter of my dissertation is a geodetic study of a M w = 7.4 subduction zone earthquake that occurred in 2012 offshore from our Guatemala GPS (Global Positioning System) network. For this study, I inverted coseismic site offsets and postseismic amplitudes to determine best-fitting coseismic and afterslip rupture distributions on the Middle America trench. I also determined the maximum likely viscoelastic deformation for the earthquake to test whether the transient postseismic deformation was dominated by fault afterslip or viscoelastic flow. This work was published in Geophysical Journal International in January 2015. The second chapter of my dissertation derives a new 200+ site GPS velocity field for northern Central America. Doing so was complicated by the occurrence of four M > 7 earthquakes since 2009, which perturbed the velocities of many of the GPS sites. To extract the interseismic velocity field from position time-series, we use TDEFNODE software to simultaneously model source parameters for coseismic rupture and transient afterslip from the 2012 El Salvador (M w = 7.3), 2012 Guatemala (Mw = 7.4), and 2009 Swan Islands (Mw = 7.3) earthquakes. The resulting, corrected best-fitting GPS site velocities are used in my third and final chapter. Finally, I address a variety of questions regarding several major faults that are the root of natural hazard studies in northern Central America. The 200+ site GPS velocity field derived in Chapter 2 far exceeds any previous velocity field for this region and represents a new standard for studying the tectonics of northern Central America. An inversion of the new velocity field using an eight-block elastic model gives the following unique or improved results with respect to previous work: 1) First evidence for a nearly rigid Chortis block south of the Motagua fault; 2) Evidence for southward transfer of slip from the western Motagua fault into the Guatemala City graben and other nearby normal faults; 3) A well-bounded estimate on partitioning of plate boundary slip on the Motagua and Polochic faults; 4) A first plate tectonic estimate of Cocos plate subduction below the Central America forearc sliver; 5) The first geodetic estimate of slip rate variations along the Central America volcanic arc, including the first slip rate estimate for the poorly-understood Jalpatagua fault in southern Guatemala; 6) The first geodetic estimate of distributed deformation in the Chiapas Tectonic Province; 7) Evidence for stronger locking offshore southern Mexico and even weaker shallow locking offshore Guatemala and El Salvador than previously estimated; 8) A refined estimate of how extension is distributed across the grabens of western Honduras and southern Guatemala; 9) Strain-rate tensors consistent with no significant deformation of the elongate Central America forearc sliver, but extension within the Gulf of Fonseca step-over in the Central America volcanic arc; 10) Evidence for slower slip along the Motagua fault than any previous estimate and a well-determined geodetic estimate for the long-term slip rate of the Polochic fault.

Precise tremor source locations and amplitude variations along the lower-crustal central San Andreas Fault

USGS Publications Warehouse

Shelly, David R.; Hardebeck, Jeanne L.

2010-01-01

We precisely locate 88 tremor families along the central San Andreas Fault using a 3D velocity model and numerous P and S wave arrival times estimated from seismogram stacks of up to 400 events per tremor family. Maximum tremor amplitudes vary along the fault by at least a factor of 7, with by far the strongest sources along a 25 km section of the fault southeast of Parkfield. We also identify many weaker tremor families, which have largely escaped prior detection. Together, these sources extend 150 km along the fault, beneath creeping, transitional, and locked sections of the upper crustal fault. Depths are mostly between 18 and 28 km, in the lower crust. Epicenters are concentrated within 3 km of the surface trace, implying a nearly vertical fault. A prominent gap in detectible activity is located directly beneath the region of maximum slip in the 2004 magnitude 6.0 Parkfield earthquake.

Interplay of plate convergence and arc migration in the central Mediterranean (Sicily and Calabria)

NASA Astrophysics Data System (ADS)

Nijholt, Nicolai; Govers, Rob; Wortel, Rinus

2016-04-01

Key components in the current geodynamic setting of the central Mediterranean are continuous, slow Africa-Eurasia plate convergence (~5 mm/yr) and arc migration. This combination encompasses roll-back, tearing and detachment of slabs, and leads to back-arc opening and orogeny. Since ~30 Ma the Apennnines-Calabrian and Gibraltar subduction zones have shaped the western-central Mediterranean region. Lithospheric tearing near slab edges and the accompanying surface expressions (STEP faults) are key in explaining surface dynamics as observed in geologic, geophysical and geodetic data. In the central Mediterranean, both the narrow Calabrian subduction zone and the Sicily-Tyrrhenian offshore thrust front show convergence, with a transfer (shear) zone connecting the distinct SW edge of the former with the less distinct, eastern limit of the latter (similar, albeit on a smaller scale, to the situation in New Zealand with oppositely verging subduction zones and the Alpine fault as the transfer shear zone). The ~NNW-SSE oriented transfer zone (Aeolian-Sisifo-Tindari(-Ionian) fault system) shows transtensive-to-strike slip motion. Recent seismicity, geological data and GPS vectors in the central Mediterranean indicate that the region can be subdivided into several distinct domains, both on- and offshore, delineated by deformation zones and faults. However, there is discussion about the (relative) importance of some of these faults on the lithospheric scale. We focus on finding the best-fitting assembly of faults for the transfer zone connecting subduction beneath Calabria and convergence north of Sicily in the Sicily-Tyrrhenian offshore thrust front. This includes determining whether the Alfeo-Etna fault, Malta Escarpment and/or Ionian fault, which have all been suggested to represent the STEP fault of the Calabrian subduction zone, are key in describing the observed deformation patterns. We first focus on the present-day. We use geodynamic models to reproduce observed GPS velocities in the Sicily-Calabria region. In these models, we combine far-field velocity boundary conditions, GPE-related body forces, and slab pull/trench suction at the subduction contacts. The location and nature of model faults are based on geological and seismicity observations, and as these faults do not fully enclose blocks our models require both fault slip and distributed strain. We vary fault friction in the models. Extrapolating the (short term) model results to geological time scales, we are able to make a first-order assessment of the regional strain and block rotations resulting from the interplay of arc migration and plate convergence during the evolution of this complex region.

The Gogebic Iron Range - A Sample of the Northern Margin of the Penokean Fold and Thrust Belt

USGS Publications Warehouse

Cannon, William F.; LaBerge, Gene L.; Klasner, John S.; Schulz, Klaus J.

2008-01-01

The Gogebic iron range is an elongate belt of Paleoproterozoic strata extending from the west shore of Lake Gogebic in the upper peninsula of Michigan for about 125 km westward into northern Wisconsin. It is one of six major informally named iron ranges in the Lake Superior region and produced about 325 million tons of direct-shipping ore between 1887 and 1967. A significant resource of concentrating-grade ore remains in the western and eastern parts of the range. The iron range forms a broad, gently southward-opening arc where the central part of the range exposes rocks that were deposited somewhat north of the eastern and western parts. A fundamental boundary marking both the tectonic setting of deposition and the later deformation within the Penokean orogen lies fortuitously in an east-west direction along the range so that the central part of the range preserves sediments deposited north of that boundary, whereas the eastern and western parts of the range were deposited south of the boundary. Thus, the central part of the range provides a record of sedimentation and very mild deformation in a part of the Penokean orogen farthest from the interior of the orogen to the south. The eastern and western parts of the range, in contrast, exhibit a depositional and deformational style typical of parts closer to the interior of the orogen. A second fortuitous feature of the iron range is that the entire area was tilted from 40° to 90° northward by Mesoproterozoic deformation so that the map view offers an oblique cross section of the Paleoproterozoic sedimentary sequence and structures. Together, these features make the Gogebic iron range a unique area in which to observe (1) the lateral transition from deposition on a stable platform to deposition in a tectonically and volcanically active region, and (2) the transition from essentially undeformed Paleoproterozoic strata to their folded and faulted equivalents.Paleoproterozoic strata in the Gogebic iron range are part of the Marquette Range Supergroup. They were deposited unconformably on Neoarchean rocks consisting of a diverse volcanic suite (the Ramsay Formation) which was intruded by granitic rocks of the Puritan Quartz Monzonite. The Marquette Range Supergroup in this region consists of a basal sequence of orthoquartzite (Sunday Quartzite) and dolomite (Bad River Dolomite), both of which are part of the Chocolay Group. The group is preserved only in the eastern and western parts of the range but was probably present throughout before the erosion interval that separated it from the overlying Menominee Group. The Menominee Group consists of basal clastic rocks (Palms Formation) that grade upward into the Ironwood Iron-Formation, which is the principal iron-bearing unit of the range. The Ironwood interfingers with the Emperor Volcanic Complex in the eastern part of the range and with volcanic rocks and gabbro in the western part of the range. The Ironwood is overlain unconformably by the Tyler Formation in the central and western parts of the range and by the Tyler’s equivalent, the Copps Formation, in the eastern part of the range.Strata in the central part of the iron range are entirely sedimentary. Deposition occurred in a relatively stable tectonic setting, at least until the deposition of the Tyler Formation. The Tyler consists largely of turbidites deposited in a foreland basin in advance of accreting volcanic arcs to the south. Penokean deformation in the central part of the range was very minor; the evidence of deformation consists of steep faults with small offsets and a few bedding-parallel faults that also have small offsets and that are recognized only in mine workings. In both the eastern and western parts of the iron range, abrupt facies changes mark a passage into a more tectonically and volcanically active belt. These relationships are especially well displayed in the east where a graben, the Presque Isle trough, began to subside during deposition of the Ironwood Iron-Formation. The thickness of the Ironwood increases into the graben and its internal stratigraphy also changes. The most prominent changes in the graben are the presence of a thick volcanic unit, the Emperor Volcanic Complex of the Menominee Group, and comagmatic gabbro sills that interfinger with the Ironwood. In the western part of the range, volcanic rocks and comagmatic gabbro sills are also present in the Ironwood, but a graben that is equivalent to the Presque Isle trough is not evident.Penokean structures are well developed in both the eastern and western parts of the iron range. They consist of folds ranging from outcrop to regional scale and thrust faults which, in places, either repeated the section or detached it from Neoarchean basement. The sharp transition from the little-deformed central part of the range to the more intensely deformed eastern and western parts coincides closely with the earlier developed transition from the stable sedimentary setting in the central part to the tectonically active sedimentation in the east and west parts. The extensional structures that formed during sedimentation may have helped to control the extent of later Penokean compressional structures.

Efforts to monitor and characterize the recent increasing seismicity in central Oklahoma

USGS Publications Warehouse

McNamara, Daniel E.; Rubinstein, Justin L.; Myers, Emma; Smoczyk, Gregory M.; Benz, Harley M.; Williams, Robert; Hayes, Gavin; Wilson, David; Herrmann, Robert B.; McMahon, Nicole D; Aster, R.C.; Bergman, E.; Holland, Austin; Earle, Paul

2015-01-01

The sharp increase in seismicity over a broad region of central Oklahoma has raised concerns regarding the source of the activity and its potential hazard to local communities and energy-industry infrastructure. Efforts to monitor and characterize the earthquake sequences in central Oklahoma are reviewed. Since early 2010, numerous organizations have deployed temporary portable seismic stations in central Oklahoma to record the evolving seismicity. A multiple-event relocation method is applied to produce a catalog of central Oklahoma earthquakes from late 2009 into early 2015. Regional moment tensor (RMT) source parameters were determined for the largest and best-recorded earthquakes. Combining RMT results with relocated seismicity enabled determination of the length, depth, and style of faulting occurring on reactivated subsurface fault systems. It was found that the majority of earthquakes occur on near-vertical, optimally oriented (northeast-southwest and northwest-southeast) strike-slip faults in the shallow crystalline basement. In 2014, 17 earthquakes occurred with magnitudes of 4 or larger. It is suggested that these recently reactivated fault systems pose the greatest potential hazard to the region.

Comparison of geologically-averaged paleomagnetic and "instantaneous" GPS rotation data in the West-Central Walker Lane

NASA Astrophysics Data System (ADS)

Farner, M. J.; Pluhar, C. J.; Carlson, C. W.

2011-12-01

The Walker Lane belt is a highly tectonically active region of dextral shear in western North America. Situated between the margins of the Sierra Nevada microplate and the Basin and Range extension, it extends northward from the Garlock Fault into portions of Southern Oregon. The Walker Lane is characterized by dextral shear accommodated by strike slip faults and left-stepping normal faults (Unruh et al, 2003). Faulting in the Walker Lane accounts for approximately 25% of the relative motion between the North American and Pacific Plates (Reheis and Dixon 1996). The study spans a region where the Sierra Nevada microplate has shed fault-bounded blocks from its eastern margin into the central Walker Lane during the Neogene. These blocks have behaved somewhat independently of one another and the Sierra Nevada as evidenced by spatially-variable magnitudes of vertical-axis rotation. This blurs the boundary of definition between microplate and fault block. One of the key questions regarding Walker Lane deformation is what is the role of rotation with respect to fault blocks and at what rate(s) does rotation occur. The software package SSPX (Cardozo and Allmendinger 2009) is used to examine previously published geodetic data to derive rotation rates in the west-central Walker Lane. A rate of 1.70° ± 0.24°/Ma is determined for Bridgeport Valley, CA based upon strain inversion of the locally-sparse GPS station data in SSPX. This rate is consistent with paleomagnetically-determined rotation rates for ~9.4 Ma members of the Stanislaus Group around Bridgeport Valley, adjacent to the Mina Deflection (e.g. King et al, 2007 and our data). However there are several shortcomings to using currently available GPS data for this purpose. GPS station spacing in many places does not provide spatial resolution of rotation comparable to the paleomagnetic dataset, which in turn limits our ability to examine small lithospheric fault blocks geodetically. The paleomagnetic data shows rotation variations on the scale of <5 km. Thus, due to GPS station spacing, our strain inversion reveals a spatially-averaged rotation for a larger given area and is not able to detect small lithospheric blocks or groups of blocks with anomalously large rotation rates of 7°/Ma or higher. An alternative hypothesis is that rotation rate is variable with time and that large rotations occurred and have slowed or stopped.

Resolving the fault systems with the magnetotelluric method in the western Ilan plain of NE Taiwan

NASA Astrophysics Data System (ADS)

Chang, P. Y.; Chen, C. S.

2017-12-01

In the study we attempt to use the magnetotelluric (MT) surveys to delineate the basement topography of the western part of the Ilan plain. The triangular plain is located on the extension part of the Okinawa Trough, and is thought to be a subsidence basin bounded by the Hsueshan Range in the north and the Central Range in the south. The basement of the basin is composed of Tertiary metamorphic rocks such as argillites and slates. The recent extension of the Okinawa Trough started from approximately 0.1 Ma and involved ENE- and WSW-trending normal faults that may extended into the Ilan plain area. However, high sedimentation rates as well as the frequent human activities have resulted in unconsolidated sediments with a thickness of over 100 meters, and caused the difficulties in observing the surface traces of the active faults in the area. Hence we deployed about 70 MT stations across the southwestern tip of the triangular plain. We also tried to resolve the subsurface faults the relief variations of the basement with the inverted resistivity images, since the saturated sediments are relatively conductive and the consolidated rocks are resistive. With the inverted MT images, we found that there are a series of N-S trending horsts and grabens in addition to the ENE-WSW normal fault systems. The ENE-WSW trending faults are dipping mainly toward the north in our study area in the western tip of the Ilan plain. The preliminary results suggest that a younger N-S trending normal fault system may modify the relief of the basement in the recent stage after the activation of the ENE-WSW normal faults. The findings of the MT resistivity images provide new information to further review the tectonic explanations of the region in the future.

Mechanical Effects of Normal Faulting Along the Eastern Escarpment of the Sierra Nevada, California

NASA Astrophysics Data System (ADS)

Martel, S. J.; Logan, J. M.; Stock, G. M.

2013-12-01

Here we test whether the regional near-surface stress field in the Sierra Nevada, California, and the near-surface fracturing that heavily influences the Sierran landscape are a mechanical response to normal faulting along its eastern escarpment. A compilation of existing near-surface stress measurements for the central Sierra Nevada, together with three new measurements, shows the most compressive horizontal stresses are 3-21 MPa, consistent with the widespread distribution of sheeting joints (near-surface fractures subparallel to the ground surface). In contrast, a new stress measurement at Aeolian Buttes in the Mono Basin, east of the range front fault system, reveals a horizontal principal tension of 0.014 MPa, consistent with the abundant vertical joints there. To evaluate mechanical effects of normal faulting, we modeled both normal faults and grabens in three ways: (1) dislocations of specified slip in an elastic half-space, (2) frictionless sliding surfaces in an elastic half-space; and (3) faults in thin elastic beams resting on an inviscid fluid. The different mechanical models predict concave upward flexure and widespread near-surface compressive stresses in the Sierra Nevada that surpass the measurements even for as little as 1 km of normal slip along the eastern escarpment, which exhibits 1-3 km of structural and topographic relief. The models also predict concave downward flexure of the bedrock floors and horizontal near-surface tensile stresses east of the escarpment. The thin-beam models account best for the topographic relief of the eastern escarpment and the measured stresses given current best estimates for the rheology of the Sierran lithosphere. Our findings collectively indicate that the regional near-surface stress field and the widespread near-surface fracturing directly reflect the mechanical response to normal faulting along the eastern escarpment. These results have broad scientific and engineering implications for slope stability, hydrology, and geomorphology in and near fault-bounded mountain ranges in general.

Geologic map of the Vail East quadrangle, Eagle County, Colorado

USGS Publications Warehouse

Kellogg, Karl S.; Bryant, Bruce; Redsteer, Margaret H.

2003-01-01

New 1:24,000-scale geologic mapping along the Interstate-70 urban corridor in western Colorado, in support of the State/USGS Cooperative Geologic Mapping Project, is contributing to a more complete understanding of the stratigraphy, structure, tectonic evolution, and hazard potential of this rapidly developing region. The 1:24,000-scale Vail East quadrangle straddles the Gore fault system, the western structural boundary of the Gore Range. The Gore fault system is a contractional structure that has been recurrently active since at least the early Paleozoic and marks the approximate eastern boundary of the Central Colorado trough, a thick late Paleozoic depocenter into which thousands of meters of clastic sediment were deposited from several uplifts, including the ancestral Front Range. The Gore fault was active during both the late Paleozoic and Upper Cretaceous-lower Tertiary (Laramide) deformations. In addition, numerous north-northwest faults that cut the crystalline rocks of the Gore Range were active during at least 5 periods, the last of which was related to Neogene uplift of the Gore Range and formation of the northern Rio Grande rift. Early Proterozoic crystalline rocks underlie the high Gore Range, north and east of the Gore fault system. These rocks consist predominantly of migmatitic biotite gneiss intruded by mostly granitic rocks of the 1.667-1.750 Ma Cross Creek batholith, part of the 1,667-1,750 Ma Routt Plutonic Suite (Tweto, 1987). Southwest of the Gore fault, a mostly gently south-dipping sequence of Pennsylvanian Mimturn Formation, as thick as 1,900 m, and the Permian and Pennsylvanian Maroon Formation (only the basal several hundred meters are exposed in the quadrangle)were shed from the ancestral Front Range and overlie a thin sequence of Devonian and Cambrian rocks. The Minturn Formation is a sequence of interlayered pink, maroon, and gray conglomerate, sandstone, shale, and marine limestone. The Maroon Formation is mostly reddish conglomerate and sandstone. Glacial till of both the middle Pleistocene Bull Lake and late Pleistocene Pinedale glaciations are well exposed along parts of the Gore Creek valley and its tributaries, although human development has profoundly altered the outcrop patterns along the Gore Creek valley bottom. Landslides, some of which are currently active, are also mapped.

Delineation of The Sumatra Fault in The Central Part of West Sumatra based on Gravity Method

NASA Astrophysics Data System (ADS)

Saragih, R. D.; Brotopuspito, K. S.

2018-04-01

The Sumatra Fault System is elongated across the Sumatra Island, Indonesia, Southeast Asia including the central part of West Sumatra, Indonesia, Southeast Asia. The Sumatra Fault and subsurface structure on the Central Part of West Sumatra had been analyzed using gravity method. Bouguer anomaly data were obtained from GRDC (Geological Research and Development Centre) maps, Bandung, Indonesia (i.e. without terrain correction). In this study, terrain correction had been applied to these Bouguer data. Bouguer anomaly in a horizontal plane at 3000 meters high and equivalent depth of mass point 7000 meters were obtained using Dampney Method. Residual and regional anomalies were separated using upward continuation method at 8000 meters high. The result of the SVD on residual anomaly shows two negative anomalies on northwest – southeast. The zero miligal per meter square quantity coincides remarkably well with trace faults which is a part of the Sumatra Fault System. Two negative anomalies are located around the Sianok Segment and Sumani Segment.

The Dauki Thrust Fault and the Shillong Anticline: An incipient plate boundary in NE India?

NASA Astrophysics Data System (ADS)

Ferguson, E. K.; Seeber, L.; Steckler, M. S.; Akhter, S. H.; Mondal, D.; Lenhart, A.

2012-12-01

The Shillong Massif is a regional contractional structure developing across the Assam sliver of the Indian plate near the Eastern Syntaxis between the Himalaya and Burma arcs. Faulting associated with the Shillong Massif is a major source of earthquake hazard. The massif is a composite basement-cored asymmetric anticline and is 100km wide, >350km long and 1.8km high. The high relief southern limb preserves a Cretaceous-Paleocene passive margin sequence despite extreme rainfall while the gentler northern limb is devoid of sedimentary cover. This asymmetry suggests southward growth of the structure. The Dauki fault along the south limb builds this relief. From the south-verging structure, we infer a regional deeply-rooted north-dipping blind thrust fault. It strikes E-W and obliquely intersects the NE-SW margin of India, thus displaying three segments: Western, within continental India; Central, along the former passive margin; and Eastern, overridden by the west-verging Burma accretion system. We present findings from recent geologic fieldwork on the western and central segments. The broadly warped erosional surface of the massif defines a single anticline in the central segment, east of the intersection with the hinge zone of the continental margin buried by the Ganges-Brahmaputra Delta. The south limb of the anticline forms a steep topographic front, but is even steeper structurally as defined by the Cretaceous-Eocene cover. Below it, Sylhet Trap Basalts intrude and cover Precambrian basement. Dikes, presumably parallel to the rifted margin, are also parallel to the front, suggesting thrust reactivation of rift-related faults. Less competent Neogene clastics are preserved only near the base of the mountain front. Drag folds in these rocks suggest north-vergence and a roof thrust above a blind thrust wedge floored by the Dauki thrust fault. West of the hinge zone, the contractional structure penetrates the Indian continent and bifurcates. After branching into the Dapsi Fault, the Dauki Fault continues westward as the erosion-deposition boundary combined with a belt of N-S shortening. The Dapsi thrust fault strikes WNW across the Shillong massif and dips NNE. It is mostly blind below a topographically expressed fold involving basement and passive-margin cover. Recent fieldwork has shown that the fault is better exposed in the west, where eventually Archean basement juxtaposes folded and steeply dipping fluvial sediment. Both Dauki and Dapsi faults probably continue beyond the Brahmaputra River, where extreme fluvial processes mask them. The area between the two faults is a gentle southward monocline with little or no shortening. Thus uplift of this area stems from slip on the Dauki thrust fault, not from pervasive shortening. The Burma foldbelt overrides the Shillong Plateau and is warped but continuous across the eastern segment of the Dauki fault. The Haflong-Naga thrust front north of the Dauki merges with the fold-thrust belt in the Sylhet basin to the south, despite >150km of differential advance due to much greater advance of the accretionary prism in the basin. Where the Dauki and Haflong-Naga thrusts cross, the thrust fronts are nearly parallel and opposite vergence. We trace a Dauki-related topographic front eastward across the Burma Range. This and other evidence suggest that the Dauki Fault continues below the foldbelt.

Geologic map of the northern White Hills, Mohave County, Arizona

USGS Publications Warehouse

Howard, Keith A.; Priest, Susan S.; Lundstrom, Scott C.; Block, Debra L.

2017-07-10

IntroductionThe northern White Hills map area lies within the Kingman Uplift, a regional structural high in which Tertiary rocks lie directly on Proterozoic rocks as a result of Cretaceous orogenic uplift and erosional stripping of Paleozoic and Mesozoic strata. The Miocene Salt Spring Fault forms the major structural boundary in the map area. This low-angle normal fault separates a footwall (lower plate) of Proterozoic gneisses on the east and south from a hanging wall (upper plate) of faulted middle Miocene volcanic and sedimentary rocks and their Proterozoic substrate. The fault is part of the South Virgin–White Hills Detachment Fault, which records significant tectonic extension that decreases from north to south. Along most of its trace, the Salt Spring Fault dips gently westward, but it also has north-dipping segments along salients. A dissected, domelike landscape on the eroded footwall, which contains antiformal salients and synformal reentrants, extends through the map area from Salt Spring Bay southward to the Golden Rule Peak area. The “Lost Basin Range” represents an upthrown block of the footwall, raised on the steeper Lost Basin Range Fault.The Salt Spring Fault, as well as the normal faults that segment its hanging wall, deform rocks that are about 16 to 10 Ma, and younger deposits overlie the faults. Rhyodacitic welded tuff about 15 Ma underlies a succession of geochemically intermediate to progressively more mafic lavas (including alkali basalt) that range from about 14.7 to 8 Ma, interfingered with sedimentary rocks and breccias in the western part of the map area. Upper Miocene strata record further filling of the extension-formed continental basins. Basins that are still present in the modern landscape reflect the youngest stages of extensional-basin formation, expressed as the downfaulted Detrital Valley and Hualapai Wash basins in the western and eastern parts of the map area, respectively, as well as the north-centrally located, northward-sagged Temple Basin. Pliocene fluvial and piedmont alluvial fan deposits record postextensional basin incision, refilling, and reincision driven by the inception and evolution of the westward-flowing Colorado River, centered north of the map area.

Quaternary Geology and Surface Faulting Hazard: Active and Capable Faults in Central Apennines, Italy

NASA Astrophysics Data System (ADS)

Falcucci, E.; Gori, S.

2015-12-01

The 2009 L'Aquila earthquake (Mw 6.1), in central Italy, raised the issue of surface faulting hazard in Italy, since large urban areas were affected by surface displacement along the causative structure, the Paganica fault. Since then, guidelines for microzonation were drew up that take into consideration the problem of surface faulting in Italy, and laying the bases for future regulations about related hazard, similarly to other countries (e.g. USA). More specific guidelines on the management of areas affected by active and capable faults (i.e. able to produce surface faulting) are going to be released by National Department of Civil Protection; these would define zonation of areas affected by active and capable faults, with prescriptions for land use planning. As such, the guidelines arise the problem of the time interval and general operational criteria to asses fault capability for the Italian territory. As for the chronology, the review of the international literature and regulatory allowed Galadini et al. (2012) to propose different time intervals depending on the ongoing tectonic regime - compressive or extensional - which encompass the Quaternary. As for the operational criteria, the detailed analysis of the large amount of works dealing with active faulting in Italy shows that investigations exclusively based on surface morphological features (e.g. fault planes exposition) or on indirect investigations (geophysical data), are not sufficient or even unreliable to define the presence of an active and capable fault; instead, more accurate geological information on the Quaternary space-time evolution of the areas affected by such tectonic structures is needed. A test area for which active and capable faults can be first mapped based on such a classical but still effective methodological approach can be the central Apennines. Reference Galadini F., Falcucci E., Galli P., Giaccio B., Gori S., Messina P., Moro M., Saroli M., Scardia G., Sposato A. (2012). Time intervals to assess active and capable faults for engineering practices in Italy. Eng. Geol., 139/140, 50-65.

Seismic influence in the Quaternary uplift of the Central Chile coastal margin, preliminary results.

NASA Astrophysics Data System (ADS)

Valdivia, D.; del Valle, F.; Marquardt, C.; Elgueta, S.

2017-12-01

In order to quantify the influence of NW striking potentially seismogenic normal faults over the longitudinal variation of the Central Chile Coastal margin uplift, we measured Quaternary marine terraces, which represent the tectonic uplift of the coastal margin. Movement in margin oblique normal faults occurs by co-seismic extension of major subduction earthquakes and has occurred in the Pichilemu fault, generating a 7.0 Mw earthquake after the 2010 8.8 Mw Maule earthquake.The coastal area between 32° and 34° S was selected due to the presence of a well-preserved sequence of 2 to 5 Quaternary marine terraces. In particular, the margin oblique normal NW-trending, SW-dipping Laguna Verde fault, south of Valparaiso (33° S) puts in contact contrasting morphologies: to the south, a flat coast with wide marine terraces is carved in both, Jurassic plutonic rocks and Neogene semi-consolidated marine sediments; to the north, a steeper scarp with narrower marine terraces, over 120 m above the corresponding ones in the southern coast, is carved in Jurassic plutonic rocks.We have collected over 6 months microseimic data, providing information on seismic activity and underground geometry of the Laguna Verde fault. We collected ca. 100 systematic measurements of fringes at the base of paleo coastal scarps through field mapping and a 5 m digital elevation model. These fringes mark the maximum sea level during the terrace's carving.The heights of these fringes range between 0 and 250 masl. We estimate a 0.7 mm/yr slip rate for the Laguna Verde fault based on the height difference between corresponding terraces north- and southward, with an average uplift rate of 0.3 mm/yr for the whole area.NW striking normal faults, besides representing a potential seismic threat to the near population on one of the most densely populated areas of Chile, heavily controls the spatial variation of the coastal margin uplift. In Laguna Verde, the uplift rate differs more than three times northward of the fault.

Logs and Scarp Data from a Paloseismic Investigation of the Surprise Valley Fault Zone, Modoc County, California

USGS Publications Warehouse

Personius, Stephen F.; Crone, Anthony J.; Machette, Michael N.; Lidke, David J.; Bradley, Lee-Ann; Mahan, Shannon

2007-01-01

This report contains field and laboratory data from a paleoseismic study of the Surprise Valley fault zone near Cedarville, California. The 85-km-long Surprise Valley fault zone forms the western active margin of the Basin and Range province in northeastern California. The down-to-the-east normal fault is marked by Holocene fault scarps along most of its length, from Fort Bidwell on the north to near the southern end of Surprise Valley. We studied the central section of the fault to determine ages of paleoearthquakes and to better constrain late Quaternary slip rates, which we hope to compare to deformation rates derived from a recently established geodetic network in the region (Hammond and Thatcher, 2005; 2007). We excavated a trench in June 2005 across a prominent fault scarp on pluvial Lake Surprise deltaic sediments near the mouth of Cooks Canyon, 4 km north of Cedarville. This site was chosen because of the presence of a well-preserved fault scarp and its development on lacustrine deposits thought to be suitable for luminescence dating. We also logged a natural exposure of the fault in similar deltaic sediments near the mouth of Steamboat Canyon, 11 km south of Cedarville, to better understand the along-strike extent of surface ruptures. The purpose of this report is to present photomosaics, trench, drill hole, and stream exposure logs; scarp profiles; and fault slip, tephrochronologic, radiocarbon, luminescence, and unit description data obtained during this investigation. We do not attempt to use the data presented herein to construct a paleoseismic history of this part of the Surprise Valley fault zone; that history will be the subject of a future report.

Complex permeability structure of a fault zone crosscutting a sequence of sandstones and shales and its influence on hydraulic head distribution

NASA Astrophysics Data System (ADS)

Cilona, A.; Aydin, A.; Hazelton, G.

2013-12-01

Characterization of the structural architecture of a 5 km-long, N40°E-striking fault zone provides new insights for the interpretation of hydraulic heads measured across and along the fault. Of interest is the contaminant transport across a portion of the Upper Cretaceous Chatsworth Formation, a 1400 m-thick turbidite sequence of sandstones and shales exposed in the Simi Hills, south California. Local bedding consistently dips about 20° to 30° to NW. Participating hydrogeologists monitor the local groundwater system by means of numerous boreholes used to define the 3D distribution of the groundwater table around the fault. Sixty hydraulic head measurements consistently show differences of 10s of meters, except for a small area. In this presentation, we propose a link between this distribution and the fault zone architecture. Despite an apparent linear morphological trend, the fault is made up of at least three distinct segments named here as northern, central and southern segments. Key aspects of the fault zone architecture have been delineated at two sites. The first is an outcrop of the central segment and the second is a borehole intersecting the northern segment at depth. The first site shows the fault zone juxtaposing sandstones against shales. Here the fault zone consists of a 13 meter-wide fault rock including a highly deformed sliver of sandstone on the northwestern side. In the sandstone, shear offset was resolved along N42°E striking and SE dipping fracture surfaces localized within a 40 cm thick strand. Here the central core of the fault zone is 8 m-wide and contains mostly shale characterized by highly diffuse deformation. It shows a complex texture overprinted by N30°E-striking carbonate veins. At the southeastern edge of the fault zone exposure, a shale unit dipping 50° NW towards the fault zone provides the key information that the shale unit was incorporated into the fault zone in a manner consistent with shale smearing. At the second site, a borehole more than 194 meter-long intersects the fault zone at its bottom. Based on an optical televiewer image supplemented by limited recovered rock cores, a juxtaposition plane (dipping 75° SE) between a fractured sandstone and a highly-deformed shale fault rock has been interpreted as the southeastern boundary of the fault zone. The shale fault rock estimated to be thicker than 4 meters is highly folded and brecciated with locally complex cataclastic texture. The observations and interpretations of the fault architecture presented above suggest that the drop of hydraulic head detected across the fault segments is due primarily to the low-permeability shaly fault rock incorporated into the fault zone by a shale smearing mechanism. Interestingly, at around the step between the northern and the central fault segments, where the fault offset is expected to diminish (no hard link and no significant shaly fault rock), the groundwater levels measured on either sides of the fault zone are more-or-less equal.

Shallow subsurface imaging of the Piano di Pezza active normal fault (central Italy) by high-resolution refraction and electrical resistivity tomography coupled with time-domain electromagnetic data

NASA Astrophysics Data System (ADS)

Villani, Fabio; Tulliani, Valerio; Sapia, Vincenzo; Fierro, Elisa; Civico, Riccardo; Pantosti, Daniela

2015-12-01

The Piano di Pezza fault is the central section of the 35 km long L'Aquila-Celano active normal fault-system in the central Apennines of Italy. Although palaeoseismic data document high Holocene vertical slip rates (˜1 mm yr-1) and a remarkable seismogenic potential of this fault, its subsurface setting and Pleistocene cumulative displacement are still poorly known. We investigated for the first time the shallow subsurface of a key section of the main Piano di Pezza fault splay by means of high-resolution seismic and electrical resistivity tomography coupled with time-domain electromagnetic soundings (TDEM). Our surveys cross a ˜5-m-high fault scarp that was generated by repeated surface-rupturing earthquakes displacing Holocene alluvial fans. We provide 2-D Vp and resistivity images, which show significant details of the fault structure and the geometry of the shallow basin infill material down to 50 m depth. Our data indicate that the upper fault termination has a sub-vertical attitude, in agreement with palaeoseismological trench evidence, whereas it dips ˜50° to the southwest in the deeper part. We recognize some low-velocity/low-resistivity regions in the fault hangingwall that we relate to packages of colluvial wedges derived from scarp degradation, which may represent the record of some Holocene palaeo-earthquakes. We estimate a ˜13-15 m throw of this fault splay since the end of the Last Glacial Maximum (˜18 ka), leading to a 0.7-0.8 mm yr-1 throw rate that is quite in accordance with previous palaeoseismic estimation of Holocene vertical slip rates. The 1-D resistivity models from TDEM soundings collected along the trace of the electrical profile significantly match with 2-D resistivity images. Moreover, they indicate that in the fault hangingwall, ˜200 m away from the surface fault trace, the pre-Quaternary carbonate basement is at ˜90-100 m depth. We therefore provide a minimal ˜150-160 m estimate of the cumulative throw of the Piano di Pezza fault system in the investigated section. We further hypothesize that the onset of the Piano di Pezza fault activity may date back to the Middle Pleistocene (˜0.5 Ma), so this is a quite young active normal fault if compared to other mature normal fault systems active since 2-3 Ma in this portion of the central Apennines.

The 10 April 2014 Nicaraguan Crustal Earthquake: Evidence of Complex Deformation of the Central American Volcanic Arc

NASA Astrophysics Data System (ADS)

Suárez, Gerardo; Muñoz, Angélica; Farraz, Isaac A.; Talavera, Emilio; Tenorio, Virginia; Novelo-Casanova, David A.; Sánchez, Antonio

2016-10-01

On 10 April 2014, an M w 6.1 earthquake struck central Nicaragua. The main event and the aftershocks were clearly recorded by the Nicaraguan national seismic network and other regional seismic stations. These crustal earthquakes were strongly felt in central Nicaragua but caused relatively little damage. This is in sharp contrast to the destructive effects of the 1972 earthquake in the capital city of Managua. The differences in damage stem from the fact that the 1972 earthquake occurred on a fault beneath the city; in contrast, the 2014 event lies offshore, under Lake Managua. The distribution of aftershocks of the 2014 event shows two clusters of seismic activity. In the northwestern part of Lake Managua, an alignment of aftershocks suggests a northwest to southeast striking fault, parallel to the volcanic arc. The source mechanism agrees with this right-lateral, strike-slip motion on a plane with the same orientation as the aftershock sequence. For an earthquake of this magnitude, seismic scaling relations between fault length and magnitude predict a sub-surface fault length of approximately 16 km. This length is in good agreement with the extent of the fault defined by the aftershock sequence. A second cluster of aftershocks beneath Apoyeque volcano occurred simultaneously, but spatially separated from the first. There is no clear alignment of the epicenters in this cluster. Nevertheless, the decay of the number of earthquakes beneath Apoyeque as a function of time shows the typical behavior of an aftershock sequence and not of a volcanic swarm. The northeast-southwest striking Tiscapa/Ciudad Jardín and Estadio faults that broke during the 1972 and 1931 Managua earthquakes are orthogonal to the fault where the 10 April earthquake occurred. These orthogonal faults in close geographic proximity show that Central Nicaragua is being deformed in a complex tectonic setting. The Nicaraguan forearc sliver, between the trench and the volcanic arc, moves to the northwest relative to the Caribbean plate at a rate of 14 mm/year. Part of the deformation is apparently accommodated by strain partitioning in the form of bookshelf faulting, on a system of orthogonal faults. The sinistral faults striking northeast-southwest rotate blocks of the Caribbean plate in a clockwise manner. The recent crustal earthquakes in central Nicaragua in 1931, 1972 and 2005 earthquakes took place on these left-lateral faults. The motion of the forearc sliver is also accommodated by a second set of right-lateral, strike-slip faults oriented parallel to the volcanic arc. Faults with this orientation and direction of motion are responsible for the 2014 and possibly the 1955 earthquakes. The presence of this geometry of orthogonal crustal faults highlights the seismic hazard posed by this complex faulting system, not only in the capital city of Managua, but also to the major Nicaraguan cities, which lie close to the volcanic arc.

Determination of the relationship between major fault and zinc mineralization using fractal modeling in the Behabad fault zone, central Iran

NASA Astrophysics Data System (ADS)

Adib, Ahmad; Afzal, Peyman; Mirzaei Ilani, Shapour; Aliyari, Farhang

2017-10-01

The aim of this study is to determine a relationship between zinc mineralization and a major fault in the Behabad area, central Iran, using the Concentration-Distance to Major Fault (C-DMF), Area of Mineralized Zone-Distance to Major Fault (AMZ-DMF), and Concentration-Area (C-A) fractal models for Zn deposit/mine classification according to their distance from the Behabad fault. Application of the C-DMF and the AMZ-DMF models for Zn mineralization classification in the Behabad fault zone reveals that the main Zn deposits have a good correlation with the major fault in the area. The distance from the known zinc deposits/mines with Zn values higher than 29% and the area of the mineralized zone of more than 900 m2 to the major fault is lower than 1 km, which shows a positive correlation between Zn mineralization and the structural zone. As a result, the AMZ-DMF and C-DMF fractal models can be utilized for the delineation and the recognition of different mineralized zones in different types of magmatic and hydrothermal deposits.

Rayleigh Wave Phase Velocities in Alaska from Ambient Noise Tomography

NASA Astrophysics Data System (ADS)

Pepin, K. S.; Li, A.; Yao, Y.

2016-12-01

We have analyzed ambient noise data recorded at 136 broadband stations from the USArray Transportable Array and other permanent seismic networks in Alaska and westernmost Canada. Daily cross-correlations are obtained using vertical component seismograms and are stacked to form a single trace for each station pair. Rayleigh wave signals are extracted from the stacked traces and are used to calculate phase velocities in the Alaska region. Preliminary phase velocity maps show similar trends to those from previous studies, but also yield new anomalies given the wider geographical range provided by the Transportable Array. At short periods (6-12s), a high velocity anomaly is observed directly northeast of the Fairweather-Queen Charlotte fault, and a high velocity trend appears in the eastern Yukon terrane between the Denali and Tintina fault, probably reflecting mafic igneous crustal rocks. Significantly slow anomalies are present at the Prince William Sound, Cook Inlet, and the basins in southwestern and central Alaska, indicating sediment effects. The slow anomalies gradually shift to southeastern and south-central Alaska with increasing period (up to 40s), corresponding to the Wrangell volcano belt and the volcano arc near Cook Inlet. A broad high-velocity zone is also observed in central Alaska to the north of the Denali fault at long periods (30-40s). The Yakutat terrane is characterized as a high-velocity anomaly from period 14s to 25s but not imaged at longer periods due to poor resolution.

Land-level changes from a late Holocene earthquake in the northern Puget lowland, Washington

USGS Publications Warehouse

Kelsey, H.M.; Sherrod, B.; Johnson, S.Y.; Dadisman, S.V.

2004-01-01

An earthquake, probably generated on the southern Whidbey Island fault zone, caused 1-2 m of ground-surface uplift on central Whidbey Island ???2800-3200 yr ago. The cause of the uplift is a fold that grew coseismically above a blind fault that was the earthquake source. Both the fault and the fold at the fault's tip are imaged on multichannel seismic refection profiles in Puget Sound immediately east of the central Whidbey Island site. Uplift is documented through contrasting histories of relative sea level at two coastal marshes on either side of the fault. Late Holocene shallow-crustal earthquakes of Mw = 6.5-7 pose substantial seismic hazard to the northern Puget Lowland. ?? 2004 Geological Society of America.

Investigation of late Pleistocene and Holocene activity in the San Gregorio fault zone on the continental slope north of Monterey Canyon, offshore central California

USGS Publications Warehouse

Maier, Katherine L.; Paull, Charles K.; Brothers, Daniel; Caress, David W.; McGann, Mary; Lundsten, Eve M.; Anderson, Krystle; Gwiazda, Roberto

2017-01-01

We provide an extensive high‐resolution geophysical, sediment core, and radiocarbon dataset to address late Pleistocene and Holocene fault activity of the San Gregorio fault zone (SGFZ), offshore central California. The SGFZ occurs primarily offshore in the San Andreas fault system and has been accommodating dextral strike‐slip motion between the Pacific and North American plates since the mid‐Miocene. Our study focuses on the SGFZ where it has been mapped through the continental slope north of Monterey Canyon. From 2009 to 2015, the Monterey Bay Aquarium Research Institute collected high‐resolution multibeam bathymetry and chirp sub‐bottom profiles using an autonomous underwater vehicle (AUV). Targeted samples were collected using a remotely operated vehicle (ROV) to provide radiocarbon age constraints. We integrate the high‐resolution geophysical data with radiocarbon dates to reveal Pleistocene seismic horizons vertically offset less than 5 m on nearly vertical faults. These faults are buried by continuous reflections deposited after ∼17.5  ka and likely following erosion during the last sea‐level lowstand ∼21  ka, bracketing the age of faulting to ∼32–21  ka. Clearly faulted horizons are only detected in a small area where mass wasting exhumed older strata to within ∼25  m of the seafloor. The lack of clearly faulted Holocene deposits and possible highly distributed faulting in the study area are consistent with previous interpretations that late Pleistocene and Holocene activity along the SGFZ may decrease to the south. This study illustrates the complexity of the SGFZ, offshore central California, and demonstrates the utility of very high‐resolution data from combined AUV (geophysical)–ROV (seabed sampling) surveys in offshore studies of fault activity.

Mechanisms for landscape evolution: Correlations between topography, lithology, erosion, and rock uplift in the central Nepalese Himalaya

NASA Astrophysics Data System (ADS)

Walsh, L. S.; Martin, A. J.; Ojha, T. P.; Fedenczuk, T.

2009-12-01

To investigate feedbacks between tectonics and erosion in the Himalaya-Tibet orogen we compare high resolution digital topography with detailed geologic maps of the Modi Khola valley in central Nepal. We examine the influence of lithologic contacts and structures on river steepness and concavity. The trace of the Bhanuwa fault, a large normal fault in Greater Himalayan rocks, coincides with the steepest location on the river profile where river steepness (ksn) reaches 884 m0.9. Transitions in ksn also occur at 1) the Romi fault, another normal fault, 2) within the Kuncha formation, 3) within Greater Himalayan rocks at the Formation I - Formation II boundary, and 4) between quartzite- and phyllite-rich parts of the Fagfog Formation. We assess mechanisms for ksn transitions on the Modi Khola by examining the influence of precipitation variability, glacial and landslide dams, tributary junctions, changes in lithology, and rock uplift on the topography. Although changes in lithology and/or landslide dams potentially explain all ksn extrema and transitions, these changes in river steepness consistently occur at normal faults suggesting possible recent motion on some of them. In detail, the Main Central thrust appears not to be the location of a major steepness change. Correlations of ksn with normal faults and lithologic contacts exhibit an important component of the landscape evolution process occurring in central Nepal and potentially other mountain belts.

Late Quaternary tectonic activity and lake level change in the Rukwa Rift Basin

NASA Astrophysics Data System (ADS)

Delvaux, D.; Kervyn, F.; Vittori, E.; Kajara, R. S. A.; Kilembe, E.

1998-04-01

Interpretation of remotely sensed images and air photographs, compilation of geological and topographical maps, morphostructural and fault kinematic observations and 14C dating reveal that, besides obvious climatic influences, the lake water extent and sedimentation in the closed hydrological system of Lake Rukwa is strongly influenced by tectonic processes. A series of sandy ridges, palaeolacustrine terraces and palaeounderwater delta fans are related to an Early Holocene high lake level and subsequent progressive lowering. The maximum lake level was controlled by the altitude of the watershed between the Rukwa and Tanganyika hydrological systems. Taking as reference the present elevation of the palaeolacustrine terraces around Lake Rukwa, two orders of vertical tectonic movement are evidenced: i) a general uplift centred on the Rungwe Volcanic Province between the Rukwa and Malawi Rift Basins; and ii) a tectonic northeastward tilting of the entire Rukwa Rift Basin, including the depression and rift shoulders. This is supported by the observed hydromorphological evolution. Local uplift is also induced by the development of an active fault zone in the central part of the depression, in a prolongation of the Mbeya Range-Galula Fault system. The Ufipa and Lupa Border Faults, bounding the Rukwa depression on the southwestern and northeastern sides, respectively, exert passive sedimentation control only. They appear inactive or at least less active in the Late Quaternary than during the previous rifting stage. The main Late Quaternary tectonic activity is represented by dextral strike-slip movement along the Mbeya Range-Galula Fault system, in the middle of the Rukwa Rift Basin, and by normal dip-slip movements along the Kanda Fault, in the western rift shoulder.

West-directed thrusting south of the eastern Himalayan syntaxis indicates clockwise crustal flow at the indenter corner during the India-Asia collision

NASA Astrophysics Data System (ADS)

Haproff, Peter J.; Zuza, Andrew V.; Yin, An

2018-01-01

Whether continental deformation is accommodated by microplate motion or continuum flow is a central issue regarding the nature of Cenozoic deformation surrounding the eastern Himalayan syntaxis. The microplate model predicts southeastward extrusion of rigid blocks along widely-spaced strike-slip faults, whereas the crustal-flow model requires clockwise crustal rotation along closely-spaced, semi-circular right-slip faults around the eastern Himalayan syntaxis. Although global positioning system (GPS) data support the crustal-flow model, the surface velocity field provides no information on the evolution of the India-Asia orogenic system at million-year scales. In this work, we present the results of systematic geologic mapping across the northernmost segment of the Indo-Burma Ranges, located directly southeast of the eastern Himalayan syntaxis. Early research inferred the area to have experienced either right-slip faulting accommodating northward indentation of India or thrusting due to the eastward continuation of the Himalayan orogen in the Cenozoic. Our mapping supports the presence of dip-slip thrust faults, rather than strike-slip faults. Specifically, the northern Indo-Burma Ranges exposes south- to west-directed ductile thrust shear zones in the hinterland and brittle fault zones in the foreland. The trends of ductile stretching lineations within thrust shear zones and thrust sheets rotate clockwise from the northeast direction in the northern part of the study area to the east direction in the southern part of the study area. This clockwise deflection pattern of lineations around the eastern Himalayan syntaxis mirrors the clockwise crustal-rotation pattern as suggested by the crustal-flow model and contemporary GPS velocity field. However, our finding is inconsistent with discrete strike-slip deformation in the area and the microplate model.

Active faulting Vs other surface displacing complex geomorphic phenomena. Case studies from a tectonically active area, Abruzzi Region, central Apennines, Italy

NASA Astrophysics Data System (ADS)

Lo Sardo, Lorenzo; Gori, Stefano; Falcucci, Emanuela; Saroli, Michele; Moro, Marco; Galadini, Fabrizio; Lancia, Michele; Fubelli, Giandomenico; Pezzo, Giuseppe

2016-04-01

How can be univocally inferred the genesis of a linear surface scarp as the result of an active and capable fault (FAC) in tectonically active regions? Or, conversely, how it is possible to exclude that a scarp is the result of a capable fault activation? Trying to unravel this open questions, we show two ambiguous case studies about the problem of the identification of active and capable faults in a tectonically active area just based on the presence of supposed fault scarps at surface. The selected cases are located in the area comprised between the Middle Aterno Valley Fault (MAVF) and the Campo Imperatore Plain (Abruzzi Region, central Apennines), nearby the epicentral area of the April 6th, 2009 L'Aquila earthquake. In particular, the two case studies analysed are located in a region characterized by a widespread Quaternary faults and by several linear scarps: the case studies of (i) Prata D'Ansidonia area and (ii) Santo Stefano di Sessanio area. To assess the origin and the state of activity of the investigated geomorphic features, we applied a classical geological and geomorphological approach, based on the analysis of the available literature, the interpretation of the aerial photographs, field surveying and classical paleoseismological approach, the latter consisting in digging excavations across the analysed scarps. These analysis were then integrated by morphometrical analyses. As for case (i), we focused on determining the geomorphic "meaning" of linear scarps carved onto fluvial-deltaic conglomerates (dated to the Early Pleistocene; Bertini and Bosi, 1993), up to 3 meters high and up to 1,5 km long, that border a narrow, elongated and flat-bottom depressions, filled by colluvial deposits. These features groove the paleo-landsurface of Valle Daria (Bosi and Bertini, 1970), wide landsurface located between Barisciano and Prata D'Ansidonia. Entwining paleoseismological trenching with geophysical analyses (GPR, ERT and microgravimetrical prospections), it could be possible to infer the genesis of the scarps as due to complex tectono-karstic phenomena. As for case (ii), our ongoing analyses are aimed to analyze the tectonic "significance" of some closed depressions, up to 4 km long and to 0,5-1 km large, that occur along the south-western slope of the Gran Sasso Range. All these small depression are NW-SE trending. As already described by Bosi et al. (1989), Galadini and Giuliani (1993), D'Agostino et al. (1998), Falcucci et al. (2015), these closed depressions are bounded by scarps carved onto the carbonate bedrock and, subordinately, onto early Quaternary slope deposits, reaching height of up to 5 m. These scarps are preferentially NE dipping, even if in few cases some SW dipping scarp are also present . The field work has permitted to attest that these scarps are related to shear planes that that displaced two subsequent of Early Pleistocene breccias formations (the Valle Valiano Fm. and Fonte Vedice Fm.; Bosi e Bertini, 1993; D'agostino et al., 1997). A paleoseismological trench was also performed across one of these scarps, attesting the activity of these shear planes also in recent times, providing indications result about the deformation style. Reference Bertini, T., & Bosi, C. (1993). La tettonica quaternaria della conca di Fossa (L'Aquila). Il Quaternario, 6(2), 293-314. Bertini, T., Bosi, C., & Galadini, F. (1989). La conca di Fossa-S. Demetrio dei Vestini. CNR, Centro di Studio per la Geologia Tecnica, ENEA, PAS in Elementi di tettonica pliocenicoquaternaria ed indizi di sismicita olocenica nell'Appennino laziale-abruzzese, Societa Geologica Italiana, L'Aquila, 26-58. Bosi, C., & Bertini, T. (1970). Geologia della media valle dell'Aterno. Memorie Società Geologica Italiana, 9(4), 719-777. D'Agostino, N., F. Speranza, & R. Funiciello., (1997) "Le Brecce Mortadella dell'Appennino Centrale: primi risultati di stratigrafia magnetica." Il Quaternario10.2: 385-388. D'Agostino, N., Chamot-Rooke, N., Funiciello, R., Jolivet, L. & Speranza, F., (1998). The role of pre-existing thrust faults and topography on the styles of extension in the Gran Sasso range (central Italy). Tectonophysics 292, 229-254. Falcucci, E., Gori, S., Moro, M., Fubelli, G., Saroli, M., Chiarabba, C., & Galadini, F. (2015). Deep reaching versus vertically restricted Quaternary normal faults: Implications on seismic potential assessment in tectonically active regions: Lessons from the middle Aterno valley fault system, central Italy. Tectonophysics, 651, 186-198. Galadini, F. & Giuliani R. (1993), Role of the structural geology analysis in the recent tectonics studies: an example from an area located SW of the Gran Sasso (Central Italy). Ann. Geof., 36 (1), 287-292.

Crustal-scale tilting of the central Salton block, southern California

USGS Publications Warehouse

Dorsey, Rebecca; Langenheim, Victoria

2015-01-01

The southern San Andreas fault system (California, USA) provides an excellent natural laboratory for studying the controls on vertical crustal motions related to strike-slip deformation. Here we present geologic, geomorphic, and gravity data that provide evidence for active northeastward tilting of the Santa Rosa Mountains and southern Coachella Valley about a horizontal axis oriented parallel to the San Jacinto and San Andreas faults. The Santa Rosa fault, a strand of the San Jacinto fault zone, is a large southwest-dipping normal fault on the west flank of the Santa Rosa Mountains that displays well-developed triangular facets, narrow footwall canyons, and steep hanging-wall alluvial fans. Geologic and geomorphic data reveal ongoing footwall uplift in the southern Santa Rosa Mountains, and gravity data suggest total vertical separation of ∼5.0–6.5 km from the range crest to the base of the Clark Valley basin. The northeast side of the Santa Rosa Mountains has a gentler topographic gradient, large alluvial fans, no major active faults, and tilted inactive late Pleistocene fan surfaces that are deeply incised by modern upper fan channels. Sediments beneath the Coachella Valley thicken gradually northeast to a depth of ∼4–5 km at an abrupt boundary at the San Andreas fault. These features all record crustal-scale tilting to the northeast that likely started when the San Jacinto fault zone initiated ca. 1.2 Ma. Tilting appears to be driven by oblique shortening and loading across a northeast-dipping southern San Andreas fault, consistent with the results of a recent boundary-element modeling study.

Fault-slip directions in central and southern Greece measured from striated and corrugated fault planes: Comparison with focal mechanism and geodetic data

NASA Astrophysics Data System (ADS)

Roberts, Gerald P.; Ganas, Athanassios

2000-10-01

Fault-slip directions recorded by outcropping striated and corrugated fault planes in central and southern Greece have been measured for comparison with extension directions derived from focal mechanism and Global Positioning System (GPS) data for the last ˜100 years to test how far back in time velocity fields and deformation dynamics derived from the latter data sets can be extrapolated. The fault-slip data have been collected from the basin-bounding faults to Plio-Pleistocene to recent extensional basins and include data from arrays of footwall faults formed during the early stages of fault growth. We show that the orientation of the inferred stress field varies along faults and earthquake ruptures, so we use only slip-directions from the centers of faults, where dip-slip motion occurs, to constrain regionally significant extension directions. The fault-slip directions for the Peloponnese and Gulfs of Evia and Corinth are statistically different at the 99% confidence level but statistically the same as those implied by earthquake focal mechanisms for each region at the 99% confidence level; they are also qualitatively similar to the principal strain axes derived from GPS studies. Extension directions derived from fault-slip data are 043-047° for the southern Peloponnese, 353° for the Gulf of Corinth, and 015-014° for the Gulf of Evia. Extension on active normal faults in the two latter areas appears to grade into strike-slip along the North Anatolian Fault through a gradual change in fault-slip directions and fault strikes. To reconcile the above with 5° Myr-1 clockwise rotations suggested for the area, we suggest that the faults considered formed during a single phase of extension. The deformation and formation of the normal fault systems examined must have been sufficiently rapid and recent for rotations about vertical axes to have been unable to disperse the fault-slip directions from the extension directions implied by focal mechanisms and GPS data. Thus, in central and southern Greece the velocity fields derived from focal mechanism and GPS data may help explain the dynamics of the deformation over longer time periods than the ˜100 years over which they were measured; this may include the entire deformation history of the fault systems considered, a time period that may exceed 1-2 Myr.

Geologic map of the Bailey 30' x 60' quadrangle, North-Central Colorado

USGS Publications Warehouse

Ruleman, Chester A.; Bohannon, Robert G.; Bryant, Bruce; Shroba, Ralph R.; Premo, Wayne R.

2011-01-01

The Bailey, Colo. 1:100,000-scale quadrangle lies within two physiographic and geologic provinces in central Colorado: 1) the Front Range and 2) South Park. Most of the Front Range is composed of Proterozoic rocks ranging in age from 1,790 Ma to 1,074 Ma. Along the eastern flanks and within the Denver Basin, sedimentary rocks ranging from Pennsylvanian to Cretaceous are deformed and steeply tilted to the east. Upper Cretaceous through Paleocene rocks were deposited in the foreland (that is, the Front Range eastern flank) and hinterland (that is, South Park) of this thrust and reverse fault system developed during the Late Cretaceous to Paleocene Laramide orogeny. Within South Park, rocks range in age from Pennsylvanian to Miocene with Quaternary deposits indicating tectonic subsidence of the basin. These rocks record five major geologic episodes: 1) the Paleozoic Anasazi uplift that formed the Ancestral Rockies, 2) the Late Cretaceous to Paleocene Laramide orogeny, 3) widespread Eocene to Oligocene volcanism, 4) Oligocene-Quaternary tectonics, and 5) Quaternary glacial episodes.

The Padul normal fault activity constrained by GPS data: Brittle extension orthogonal to folding in the central Betic Cordillera

NASA Astrophysics Data System (ADS)

Gil, Antonio J.; Galindo-Zaldívar, Jesús; Sanz de Galdeano, Carlos; Borque, Maria Jesús; Sánchez-Alzola, Alberto; Martinez-Martos, Manuel; Alfaro, Pedro

2017-08-01

The Padul Fault is located in the Central Betic Cordillera, formed in the framework of the NW-SE Eurasian-African plate convergence. In the Internal Zone, large E-W to NE-SW folds of western Sierra Nevada accommodated the greatest NW-SE shortening and uplift of the cordillera. However, GPS networks reveal a present-day dominant E-W to NE-SW extensional setting at surface. The Padul Fault is the most relevant and best exposed active normal fault that accommodates most of the NE-SW extension of the Central Betics. This WSW-wards dipping fault, formed by several segments of up to 7 km maximum length, favored the uplift of the Sierra Nevada footwall away from the Padul graben hanging wall. A non-permanent GPS network installed in 1999 constrains an average horizontal extensional rate of 0.5 mm/yr in N66°E direction. The fault length suggests that a (maximum) 6 magnitude earthquake may be expected, but the absence of instrumental or historical seismic events would indicate that fault activity occurs at least partially by creep. Striae on fault surfaces evidence normal-sinistral kinematics, suggesting that the Padul Fault may have been a main transfer fault of the westernmost end of the Sierra Nevada antiform. Nevertheless, GPS results evidence: (1) shortening in the Sierra Nevada antiform is in its latest stages, and (2) the present-day fault shows normal with minor oblique dextral displacements. The recent change in Padul fault kinematics will be related to the present-day dominance of the ENE-WSW regional extension versus NNW-SSE shortening that produced the uplift and northwestwards displacement of Sierra Nevada antiform. This region illustrates the importance of heterogeneous brittle extensional tectonics in the latest uplift stages of compressional orogens, as well as the interaction of folding during the development of faults at shallow crustal levels.

Earthquake probabilities for the Wassatch front region in Utah, Idaho, and Wyoming

USGS Publications Warehouse

Wong, Ivan G.; Lund, William R.; Duross, Christopher; Thomas, Patricia; Arabasz, Walter; Crone, Anthony J.; Hylland, Michael D.; Luco, Nicolas; Olig, Susan S.; Pechmann, James; Personius, Stephen; Petersen, Mark D.; Schwartz, David P.; Smith, Robert B.; Rowman, Steve

2016-01-01

In a letter to The Salt Lake Daily Tribune in September 1883, U.S. Geological Survey (USGS) geologist G.K. Gilbert warned local residents about the implications of observable fault scarps along the western base of the Wasatch Range. The scarps were evidence that large surface-rupturing earthquakes had occurred in the past and more would likely occur in the future. The main actor in this drama is the 350-km-long Wasatch fault zone (WFZ), which extends from central Utah to southernmost Idaho. The modern Wasatch Front urban corridor, which follows the valleys on the WFZ’s hanging wall between Brigham City and Nephi, is home to nearly 80% of Utah’s population of 3 million. Adding to this circumstance of “lots of eggs in one basket,” more than 75% of Utah’s economy is concentrated along the Wasatch Front in Utah’s four largest counties, literally astride the five central and most active segments of the WFZ.

Clustering of velocities in a GPS network spanning the Sierra Nevada Block, the Northern Walker Lane Belt, and the Central Nevada Seismic Belt, California-Nevada

NASA Astrophysics Data System (ADS)

Savage, J. C.; Simpson, R. W.

2013-09-01

The deformation across the Sierra Nevada Block, the Walker Lane Belt, and the Central Nevada Seismic Belt (CNSB) between 38.5°N and 40.5°N has been analyzed by clustering GPS velocities to identify coherent blocks. Cluster analysis determines the number of clusters required and assigns the GPS stations to the proper clusters. The clusters are shown on a fault map by symbols located at the positions of the GPS stations, each symbol representing the cluster to which the velocity of that GPS station belongs. Fault systems that separate the clusters are readily identified on such a map. Four significant clusters are identified. Those clusters are strips separated by (from west to east) the Mohawk Valley-Genoa fault system, the Pyramid Lake-Wassuk fault system, and the Central Nevada Seismic Belt. The strain rates within the westernmost three clusters approximate simple right-lateral shear (~13 nstrain/a) across vertical planes roughly parallel to the cluster boundaries. Clustering does not recognize the longitudinal segmentation of the Walker Lane Belt into domains dominated by either northwesterly trending, right-lateral faults or northeasterly trending, left-lateral faults.

Clustering of velocities in a GPS network spanning the Sierra Nevada Block, the northern Walker Lane Belt, and the Central Nevada Seismic Belt, California-Nevada

USGS Publications Warehouse

Savage, James C.; Simpson, Robert W.

2013-01-01

The deformation across the Sierra Nevada Block, the Walker Lane Belt, and the Central Nevada Seismic Belt (CNSB) between 38.5°N and 40.5°N has been analyzed by clustering GPS velocities to identify coherent blocks. Cluster analysis determines the number of clusters required and assigns the GPS stations to the proper clusters. The clusters are shown on a fault map by symbols located at the positions of the GPS stations, each symbol representing the cluster to which the velocity of that GPS station belongs. Fault systems that separate the clusters are readily identified on such a map. Four significant clusters are identified. Those clusters are strips separated by (from west to east) the Mohawk Valley-Genoa fault system, the Pyramid Lake-Wassuk fault system, and the Central Nevada Seismic Belt. The strain rates within the westernmost three clusters approximate simple right-lateral shear (~13 nstrain/a) across vertical planes roughly parallel to the cluster boundaries. Clustering does not recognize the longitudinal segmentation of the Walker Lane Belt into domains dominated by either northwesterly trending, right-lateral faults or northeasterly trending, left-lateral faults.

Late Cenozoic cooling history of the central Menderes Massif: Timing of the Büyük Menderes detachment and the relative contribution of normal faulting and erosion to rock exhumation

NASA Astrophysics Data System (ADS)

Wölfler, Andreas; Glotzbach, Christoph; Heineke, Caroline; Nilius, Nils-Peter; Hetzel, Ralf; Hampel, Andrea; Akal, Cüneyt; Dunkl, István; Christl, Marcus

2017-10-01

Based on new thermochronological data and 10Be-derived erosion rates from the southern part of the central Menderes Massif (Aydın block) in western Turkey, we provide new insights into the tectonic evolution and landscape development of an area that undergoes active continental extension. Fission-track and (U-Th)/He data reveal that the footwall of the Büyük Menderes detachment experienced two episodes of enhanced cooling and exhumation. Assuming an elevated geothermal gradient of 50 °C/km, the first phase occurred with an average rate of 0.90 km/Myr in the middle Miocene and the second one in the latest Miocene and Pliocene with a rate of 0.43 km/Myr. The exhumation rates between these two phases were lower and range from 0.14 to 0.24 km/Myr, depending on the distance to the detachment. Cosmogenic nuclide-based erosion rates for catchments in the Aydın block range from 0.1 to 0.4 km/Myr. The similarity of the erosion rates on both sides of the Aydın block (northern and southern flank) indicate that a rather symmetric erosion pattern has prevailed during the Holocene. If these millennial erosion rates are representative on a million-year timescale they indicate that, apart from normal faulting, erosion in the hanging wall of the Büyük Menderes detachment fault did also contribute to the exhumation of the metamorphic rocks.

Kinematic Evolution of the North-Tehran Fault (NTF), Alborz Mountains, Iran

NASA Astrophysics Data System (ADS)

Landgraf, A.; Ballato, P.; Strecker, M. R.; Shahpasandzadeh, M.; Friedrich, A.; Tabatabaei, S. H.

2007-12-01

The ENE-to NW-striking NTF is an active frontal thrust that delimits the Alborz Mountain range to the south with an up to 2000 m topographic break with respect to the adjacent Tehran plain. Eocene rocks of the Alborz range are thrusted over Neogene and Quaternary sediments of the alluvial Tehran embayment. The fault consists of right- stepping segments and merges to the east with the active Mosha-Fasham strike-slip fault (MFF). The complex tectonic history, involving changes in the direction of SHmax, has resulted in a composite tectonic landscape with inherited topographic and fault-kinematic fingerprints along the NTF. We therefore used a combination of fault-kinematic measurements and geomorphic observations to unravel the temporal tectonic evolution of this fault. Presently, the NTF is virtually inactive, although the tectonically overprinted landforms reflect tectonic activity on longer time scales during the Quaternary. Being located adjacent north of the Tehran megacity, there is thus considerable interest to decipher its youngest tectonic evolution and to better understand the relation with other fault systems. Our fault kinematic study has revealed an early dextral kinematic history for the NTF. Dextral strike-slip and oblique reverse faulting took place during NW-oriented shortening. The overall fault-geometry of the NTF suggests that it has evolved in relation to dextral transpression along the MFF. This early kinematic regime was superseded by NE-oriented shortening, associated with sinistral-oblique thrusting along the fault segments. Fault linkage between the semi-independent ENE-striking NTF-segments and NW-striking thrusts (Emamzadeh Davud Fault [EDF], Purkan Vardij Thrust [PVT], NTF-prolongation) point towards an evolution into a nascent transpressional duplex. In this scenario the NTF segments constitute lateral ramps and the NW-striking faults act as frontal ramps. Topographic residuals, as an expression of high-uplift zones, indicate that the central segment of the NTF, incorporating the EDF was most effective in accommodating oblique convergence during this time. However, subtle knickpoints in the longitudinal river profiles crossing the PVT may indicate a relatively recent transfer of deformation onto this block. The youngest manifestations of deformation along the NTF, however, are left-lateral and normal faulting. This youngest phase of activity is documented by numerous striated and rotated conglomeratic clasts, meter-scale fault gouge zones with shear-sense indicators of oblique normal faulting, and multiple colluvial wedges with drag phenomena. Rupture traces and filled extensional cracks reaching the surface also document the seismogenic nature of these features. Since recent left-lateral transtension is also known from neighboring faults, e.g., the eastern MFF, our observations suggest that this youngest phase of tectonic activity of the NTF is a regional phenomenon, rather than the result of locally-determined geometries.

Identification of a new fault and associated lineament features in Oregon's Summer Lake Valley using high-resolution LiDAR data

NASA Astrophysics Data System (ADS)

Bennett, L.; Madin, I.

2012-12-01

In 2012, the Oregon Department of Geology and Mineral Industries (DOGAMI) contracted WSI to co-acquire airborne Light Detecting and Ranging (LiDAR) and Thermal Infrared Imagery (TIR) data within the region surrounding Summer Lake, Oregon. The objective of this project was to detect surficial expressions of geothermal activity and associated geologic features. An analysis of the LiDAR data revealed one newly identified fault and several accompanying lineaments that strike northwest, similar to the trend of the Ana River, Brothers, and Eugene-Denio Fault Zones in Central Oregon. The age of the Ana River Fault Zone and Summer Lake bed is known to be within the Holocene epoch. Apparent scarp height observed from the LiDAR is up to 8 meters. While detailed analysis is ongoing, the data illustrated the effectiveness of using high resolution remote sensing data for surficial analysis of geologic displacement. This presentation will focus on direct visual detection of features in the Summer Lake, Oregon landscape using LiDAR data.

Prospects for earthquake prediction and control

USGS Publications Warehouse

Healy, J.H.; Lee, W.H.K.; Pakiser, L.C.; Raleigh, C.B.; Wood, M.D.

1972-01-01

The San Andreas fault is viewed, according to the concepts of seafloor spreading and plate tectonics, as a transform fault that separates the Pacific and North American plates and along which relative movements of 2 to 6 cm/year have been taking place. The resulting strain can be released by creep, by earthquakes of moderate size, or (as near San Francisco and Los Angeles) by great earthquakes. Microearthquakes, as mapped by a dense seismograph network in central California, generally coincide with zones of the San Andreas fault system that are creeping. Microearthquakes are few and scattered in zones where elastic energy is being stored. Changes in the rate of strain, as recorded by tiltmeter arrays, have been observed before several earthquakes of about magnitude 4. Changes in fluid pressure may control timing of seismic activity and make it possible to control natural earthquakes by controlling variations in fluid pressure in fault zones. An experiment in earthquake control is underway at the Rangely oil field in Colorado, where the rates of fluid injection and withdrawal in experimental wells are being controlled. ?? 1972.

The development of the East African Rift system in north-central Kenya

NASA Astrophysics Data System (ADS)

Hackman, B. D.; Charsley, T. J.; Key, R. M.; Wilkinson, A. F.

1990-11-01

Between 1980 and 1986 geological surveying to produce maps on a scale of 1:250,000 was completed over an area of over 100,000 km 2 in north-central Kenya, bounded by the Equator, the Ethiopian border and longitudes 36° and 38 °E. The Gregory Rift, much of which has the structure of an asymmetric half-graben, is the most prominent component of the Cenozoic multiple rift system which extends up to 200 km to the east and for about 100 km to the west, forming the Kenya dome. On the eastern shoulder and fringes two en echelon arrays of late Tertiary to Quaternary multicentre shields can be recognized: to the south is the Aberdares-Mount Kenya-Nyambeni Range chain and, to the north the clusters of Mount Kulal, Asie, Huri Hills and Marsabit, with plateau lavas and fissure vents south of Marsabit in the Laisamis area. The Gregory Rift terminates at the southern end of Lake Turkana. Further north the rift system splays: the arcuate Kinu Sogo fault zone forms an offset link with the central Ethiopian Rift system. In the rifts of north-central Kenya volcanism, sedimentation and extensional tectonics commenced and have been continuous since the late Oligocene. Throughout this period the Elgeyo Fault acted as a major bounding fault. A comparative study of the northern and eastern fringes of the Kenya dome with the axial graben reinforces the impression of regional E-W asymmetry. Deviations from the essential N-trend of the Gregory Rift reflect structural weaknesses in the underlying Proterozoic basement, the Mozambique Orogenic Belt: thus south of Lake Baringo the swing to the southeast parallels the axes of the ca. 620 Ma phase folds. Secondary faults associated with this flexure have created a "shark tooth" array, an expression of en echelon offsets of the eastern margin of the Gregory Rift in a transtensional stress regime: hinge zones where major faults intersect on the eastern shoulder feature intense box faulting and ramp structures which have counterparts in the rift system in southern Ethiopia. The NE- and ENE-trending fissures of the eastern fringes of the Kenya dome, notably in the Meru-Nyambeni areaand in the Huri and Marsabit shields, parallel late orogenic structures dated at around 580-480 Ma. Alkaline trends characterize the petrochemistry of the Cenozoic volcanics: In the Gregory Rift, voluminous Miocene alkali basalts, associated with hawaiite/mugearite lavas, define a trend culminating in the Miocene flood phonolites of the eastern shoulderand in the trachyphonolites, trachytes and peralkaline rhyolites, with associated pyroclastics, in central volcanoes such as Korosi, Paka and Silali. Such trends may manifest in the products of a single volcanic centre, also regionally on a broadly cyclic basis. On the eastern flanks of the Kenya dome the flood phonolites are less evident, but the same alkaline trends dominate the lava sequences, supplemented by nephelinitic extrusives in parts of the Nyambeni Range and in the Laisamis area. Results from recent seismicity surveys in the Laisamis area indicate that crustal extension may be currently active on the eastern fringes of the Kenya dome, but manifest at greater depths than in the axial Gregory Rift-Lake Turkana zone: a correlation is suggested with the ultra-alkaline petrochemistry of some of the eastern multicentre shields.

Active faulting in apparently stable peninsular India: Rift inversion and a Holocene-age great earthquake on the Tapti Fault

NASA Astrophysics Data System (ADS)

Copley, Alex; Mitra, Supriyo; Sloan, R. Alastair; Gaonkar, Sharad; Reynolds, Kirsty

2014-08-01

We present observations of active faulting within peninsular India, far from the surrounding plate boundaries. Offset alluvial fan surfaces indicate one or more magnitude 7.6-8.4 thrust-faulting earthquakes on the Tapti Fault (Maharashtra, western India) during the Holocene. The high ratio of fault displacement to length on the alluvial fan offsets implies high stress-drop faulting, as has been observed elsewhere in the peninsula. The along-strike extent of the fan offsets is similar to the thickness of the seismogenic layer, suggesting a roughly equidimensional fault rupture. The subsiding footwall of the fault is likely to have been responsible for altering the continental-scale drainage pattern in central India and creating the large west flowing catchment of the Tapti river. A preexisting sedimentary basin in the uplifting hanging wall implies that the Tapti Fault was active as a normal fault during the Mesozoic and has been reactivated as a thrust, highlighting the role of preexisting structures in determining the rheology and deformation of the lithosphere. The slip sense of faults and earthquakes in India suggests that deformation south of the Ganges foreland basin is driven by the compressive force transmitted between India and the Tibetan Plateau. The along-strike continuation of faulting to the east of the Holocene ruptures we have studied represents a significant seismic hazard in central India.

Distribution, facies, ages, and proposed tectonic associations of regionally metamorphosed rocks in east- and south-central Alaska

USGS Publications Warehouse

Dusel-Bacon, Cynthia; Csejtey, Bela; Foster, Helen L.; Doyle, Elizabeth O.; Nokleberg, Warren J.; Plafker, George

1993-01-01

Most of the exposed bedrock in east- and south-central Alaska has been regionally metamorphosed and deformed during Mesozoic and early Cenozoic time. All the regionally metamorphosed rocks are assigned to metamorphic-facies units on the basis of their temperature and pressure conditions and metamorphic age. North of the McKinley and Denali faults, the crystalline rocks of the Yukon- Tanana upland and central Alaska Range compose a sequence of dynamothermally metamorphosed Paleozoic and older(?) metasedimentary rocks and metamorphosed products of a Devonian and Mississippian continental-margin magmatic arc. This sequence was extensively intruded by postmetamorphic mid-Cretaceous and younger granitoids. Many metamorphic-unit boundaries in the Yukon-Tanana upland are low-angle faults that juxtapose units of differing metamorphic grade, which indicates that metamorphism predated final emplacement of the fault-bounded units. In some places, the relation of metamorphic grade across a fault is best explained by contractional faulting; in other places, it is suggestive of extensional faulting.Near the United States-Canadian border in the central Yukon- Tanana upland, metamorphism, plutonism, and thrusting occurred during a latest Triassic and Early Jurassic event that presumably resulted from the accretion of a terrane that had affinities to the Stikinia terrane onto the continental margin of North America. Elsewhere in the Yukon-Tanana upland, metamorphic rocks give predominantly late Early Cretaceous isotopic ages. These ages are interpreted to date either the timing of a subsequent Early Cretaceous episode of crustal thickening and metamorphism or, assuming that these other areas were also originally heated during the latest Triassic to Early Jurassic and remained buried, the timing of their uplift and cooling. This uplift and cooling may have resulted from extension.South of the McKinley and Denali faults and north of the Border Ranges fault system, medium-grade metamorphism across much of the southern Peninsular and Wrangellia terranes was early to synkinematic with the intrusion of tonalitic and granodioritic plutons of primarily Early and Middle Jurassic age in the Peninsular terrane and Late Jurassic age in the Wrangellia terrane. Areas metamorphosed during the Jurassic episode that crop out near the Border Ranges fault system were subsequently retrograded and deformed in Cretaceous and early Tertiary time during accretion of younger units to the south. North of the Jurassic metamorphic and plutonic complex, low-grade metamorphism affected the rest of the Wrangellia terrane sometime during Jurassic and (or) Cretaceous time.North of the Wrangellia terrane and immediately south of the McKinley and Denali faults, flyschoid rocks, which were deposited within a basin that separated the Wrangellia terrane from the western margin of North America, form a northeastward-tapering wedge. Within the western half of the wedge, flysch and structurally interleaved tectonic fragments were highly deformed and weakly metamorphosed; much of the metamorphism and deformation probably occurred sometime during mid- to Late Cretaceous time. In the eastern half of the wedge, flyschoid rocks form an intermediate-pressure Barrovian sequence (Maclaren metamorphic belt). Metamorphism of the Maclaren metamorphic belt was synkinematic with the Late Cretaceous to earliest Tertiary intrusion of foliated plutons of intermediate composition. Isotopic data suggest metamorphism extended into the early Tertiary and was accompanied by rapid uplift and cooling. Low- to medium-grade metamorphism throughout the wedge was probably associated with the accretion of the outboard Wrangellia terrane, as has been proposed for the Maclaren metamorphic belt.South of the Border Ranges fault system lie variably metamorphosed sequences of oceanic rocks that comprise the successively accreted Chugach, Yakutat, Ghost Rocks, and Prince William terranes. The Chugach terrane consists of three successively accreted sequences of differing metamorphic histories. Metamorphism in all the sequences was associated with north-directed underthrusting beneath either the combined Peninsular-Wrangellia terrane or the older and inner parts of the Chugach terrane. These sequences, from innermost to outermost are: (1) intermediate- to highpressure, transitional greenschist- to blueschist-facies metabasalt and metasedimentary rocks that were metamorphosed during the Early and Middle Jurassic; (2) prehnite-pumpellyite-facies melange that was metamorphosed sometime during the Jurassic and Cretaceous; and (3) low-pressure prehnite-pumpellyite- or greenschist- facies flysch and metavolcanic rocks that were initially metamorphosed during latest Cretaceous to early Tertiary time and, in the eastern Chugach Mountains, were subsequently overprinted by low-pressure amphibolite-facies metamorphism that accompanied widespread intrusion during Eocene time. A similar low-pressure-facies series also developed within melange and flysch of the Yakutat terrane; these rocks are also intruded by Eocene plutons and are correlated with similar rocks of the Chugach terrane.Seaward of the Chugach terrane are the strongly deformed but weakly metamorphosed (prehnite-pumpellyite-facies) deep-sea metasedimentary rocks and oceanic metavolcanic rocks of the Ghost Rocks and Prince William terranes. Metamorphism and deformation occurred during underthrusting of these terranes beneath the Chugach terrane in early Tertiary time and predated, perhaps by very little, intrusion by early Tertiary granitoids.

Sedimentary and tectonic evolution of Plio Pleistocene alluvial and lacustrine deposits of Fucino Basin (central Italy)

NASA Astrophysics Data System (ADS)

Cavinato, Gian Paolo; Carusi, Claudio; Dall'Asta, Massimo; Miccadei, Enrico; Piacentini, Tommaso

2002-04-01

The Fucino Basin was the greatest lake of the central Italy, which was completely drained at the end of 19th century. The basin is an intramontane half-graben filled by Plio-Quaternary alluvial and lacustrine deposits located in the central part of the Apennines chain, which was formed in Upper Pliocene and in Quaternary time by the extensional tectonic activity. The analysis of the geological surface data allows the definition of several stratigraphic units grouped in Lower Units and Upper Units. The Lower Units (Upper Pliocene) are exposed along the northern and north-eastern basin margins. They consist of open to marginal lacustrine deposits, breccia deposits and fluvial deposits. The Upper Units (Lower Pliocene-Holocene) consist of interbedded marginal lacustrine deposits and fluvial deposits; thick coarse-grained fan-delta deposits are interfingered at the foot of the main relief with fluvial-lacustrine deposits. Most of the thickness of the lacustrine sequences (more than 1000-m thick) is buried below the central part of the Fucino Plain. The basin is bounded by E-W, WSW-ENE and NW-SE fault systems: Velino-Magnola Fault (E-W) and Tremonti-Celano-Aielli Fault (WSW-ENE) and S. Potito-Celano Fault (NW-SE) in the north; the Trasacco Fault, the Pescina-Celano Fault and the Serrone Fault (NW-SE) in the south-east. The geometry and kinematic indicators of these faults indicate normal or oblique movements. The study of industrial seismic profiles across the Fucino Basin gives a clear picture of the subsurface basin geometry; the basin shows triangular-shaped basin-fill geometry, with the maximum deposits thickness toward the main east boundary fault zones that dip south-westward (Serrone Fault, Trasacco Fault, Pescina-Celano Fault). On the basis of geological surface data, borehole stratigraphy and seismic data analysis, it is possible to recognize and to correlate sedimentary and seismic facies. The bottom of the basin is well recognized in the seismic lines available from the good and continuous signals of the top of Meso-Cenozoic carbonate rocks. The shape of sedimentary bodies indicates that the filling of the basin was mainly controlled by normal slip along the NW-SE boundary faults. In fact, the continental deposits are frequently in on-lap contact over the carbonate substratum; several disconformable contacts occurred during the sedimentary evolution of the basin. The main faults (with antithetic and synthetic fault planes) displace the whole sedimentary sequence up to the surface indicating a recent faults' activity (1915 Avezzano earthquake, Ms=7.0). The stratigraphic and tectonic setting of the Fucino Basin and neighboring areas indicates that the extensional tectonic events have had an important role in driving the structural-sedimentary evolution of the Plio-Quaternary deposits. The geometry of the depositional bodies, of the fault planes and their relationships indicate that the Fucino Basin was formed as a half-graben type structure during Plio-Quaternary extensional events. Some internal complexities are probably related to the fold-and-thrust structures of the Apenninic orogeny formed in Messinian time, in this area, and to a different activity timing of the E-W and WSW-ENE fault systems and the NW-SE fault systems. We believe, based on the similarity of the surface characteristics, that the structural setting of the Fucino Basin can be extrapolated to the other great intramontane basins in Central Italy (e.g. Rieti, L'Aquila, Sulmona, Sora, Isernia basins).

Active faults in Africa: a review

NASA Astrophysics Data System (ADS)

Skobelev, S. F.; Hanon, M.; Klerkx, J.; Govorova, N. N.; Lukina, N. V.; Kazmin, V. G.

2004-03-01

The active fault database and Map of active faults in Africa, in scale of 1:5,000,000, were compiled according to the ILP Project II-2 "World Map of Major Active Faults". The data were collected in the Royal Museum of Central Africa, Tervuren, Belgium, and in the Geological Institute, Moscow, where the final edition was carried out. Active faults of Africa form three groups. The first group is represented by thrusts and reverse faults associated with compressed folds in the northwest Africa. They belong to the western part of the Alpine-Central Asian collision belt. The faults disturb only the Earth's crust and some of them do not penetrate deeper than the sedimentary cover. The second group comprises the faults of the Great African rift system. The faults form the known Western and Eastern branches, which are rifts with abnormal mantle below. The deep-seated mantle "hot" anomaly probably relates to the eastern volcanic branch. In the north, it joins with the Aden-Red Sea rift zone. Active faults in Egypt, Libya and Tunis may represent a link between the East African rift system and Pantellerian rift zone in the Mediterranean. The third group included rare faults in the west of Equatorial Africa. The data were scarce, so that most of the faults of this group were identified solely by interpretation of space imageries and seismicity. Some longer faults of the group may continue the transverse faults of the Atlantic and thus can penetrate into the mantle. This seems evident for the Cameron fault line.

Research on Fault Characteristics and Line Protections Within a Large-scale Photovoltaic Power Plant

NASA Astrophysics Data System (ADS)

Zhang, Chi; Zeng, Jie; Zhao, Wei; Zhong, Guobin; Xu, Qi; Luo, Pandian; Gu, Chenjie; Liu, Bohan

2017-05-01

Centralized photovoltaic (PV) systems have different fault characteristics from distributed PV systems due to the different system structures and controls. This makes the fault analysis and protection methods used in distribution networks with distributed PV not suitable for a centralized PV power plant. Therefore, a consolidated expression for the fault current within a PV power plant under different controls was calculated considering the fault response of the PV array. Then, supported by the fault current analysis and the on-site testing data, the overcurrent relay (OCR) performance was evaluated in the collection system of an 850 MW PV power plant. It reveals that the OCRs at downstream side on overhead lines may malfunction. In this case, a new relay scheme was proposed using directional distance elements. In the PSCAD/EMTDC, a detailed PV system model was built and verified using the on-site testing data. Simulation results indicate that the proposed relay scheme could effectively solve the problems under variant fault scenarios and PV plant output levels.

A kinematic model for the evolution of the Eastern California Shear Zone and Garlock Fault, Mojave Desert, California

NASA Astrophysics Data System (ADS)

Dixon, Timothy H.; Xie, Surui

2018-07-01

The Eastern California shear zone in the Mojave Desert, California, accommodates nearly a quarter of Pacific-North America plate motion. In south-central Mojave, the shear zone consists of six active faults, with the central Calico fault having the fastest slip rate. However, faults to the east of the Calico fault have larger total offsets. We explain this pattern of slip rate and total offset with a model involving a crustal block (the Mojave Block) that migrates eastward relative to a shear zone at depth whose position and orientation is fixed by the Coachella segment of the San Andreas fault (SAF), southwest of the transpressive "big bend" in the SAF. Both the shear zone and the Garlock fault are assumed to be a direct result of this restraining bend, and consequent strain redistribution. The model explains several aspects of local and regional tectonics, may apply to other transpressive continental plate boundary zones, and may improve seismic hazard estimates in these zones.

Triggered surface slips in the Salton Trough associated with the 1999 Hector Mine, California, earthquake

USGS Publications Warehouse

Rymer, M.J.; Boatwright, J.; Seekins, L.C.; Yule, J.D.; Liu, J.

2002-01-01

Surface fracturing occurred along the southern San Andreas, Superstition Hills, and Imperial faults in association with the 16 October 1999 (Mw 7.1) Hector Mine earthquake, making this at least the eighth time in the past 31 years that a regional earthquake has triggered slip along faults in the Salton Trough. Fractures associated with the event formed discontinuous breaks over a 39-km-long stretch of the San Andreas fault, from the Mecca Hills southeastward to Salt Creek and Durmid Hill, a distance from the epicenter of 107 to 139 km. Sense of slip was right lateral; only locally was there a minor (~1 mm) vertical component of slip. Dextral slip ranged from 1 to 13 mm. Maximum slip values in 1999 and earlier triggered slips are most common in the central Mecca Hills. Field evidence indicates a transient opening as the Hector Mine seismic waves passed the southern San Andreas fault. Comparison of nearby strong-motion records indicates several periods of relative opening with passage of the Hector Mine seismic wave-a similar process may have contributed to the field evidence of a transient opening. Slip on the Superstition Hills fault extended at least 9 km, at a distance from the Hector Mine epicenter of about 188 to 196 km. This length of slip is a minimum value, because we saw fresh surface breakage extending farther northwest than our measurement sites. Sense of slip was right lateral; locally there was a minor (~1 mm) vertical component of slip. Dextral slip ranged from 1 to 18 mm, with the largest amounts found distributed (or skewed) away from the Hector Mine earthquake source. Slip triggered on the Superstition Hills fault commonly is skewed away from the earthquake source, most notably in 1968, 1979, and 1999. Surface slip on the Imperial fault and within the Imperial Valley extended about 22 km, representing a distance from the Hector Mine epicenter of about 204 to 226 km. Sense of slip dominantly was right lateral; the right-lateral component of slip ranged from 1 to 19 mm. Locally there was a minor (~1-2 mm) vertical component of slip; larger proportions of vertical slip (up to 10 mm) occurred in Mesquite basin, where scarps indicate long-term oblique-slip motion for this part of the Imperial fault. Slip triggered on the Imperial fault appears randomly distributed relative to location along the fault and source direction. Multiple surface slips, both primary and triggered slip, indicate that slip repeatedly is small at locations of structural complexity.

Evolution of Late Miocene to Contemporary Displacement Transfer Between the Northern Furnace Creek and Southern Fish Lake Valley Fault Zones and the Central Walker Lane, Western Great Basin, Nevada

NASA Astrophysics Data System (ADS)

Oldow, J. S.; Geissman, J. W.

2013-12-01

Late Miocene to contemporary displacement transfer from the north Furnace Creek (FCF) and southern Fish Lake Valley (FLVF) faults to structures in the central Walker Lane was and continues to be accommodated by a belt of WNW-striking left-oblique fault zones in the northern part of the southern Walker Lane. The WNW fault zones are 2-9 km wide belts of anastomosing fault strands that intersect the NNW-striking FCF and southern FLVF in northern Death Valley and southern Fish Lake Valley, respectively. The WNW fault zones extend east for over 60 km where they merge with a 5-10 km wide belt of N10W striking faults that marks the eastern boundary of the southern Walker Lane. Left-oblique displacement on WNW faults progressively decreases to the east, as motion is successively transferred northeast on NNE-striking faults. NNE faults localize and internally deform extensional basins that each record cumulative net vertical displacements of between 3.0 and 5.2 km. The transcurrent faults and associated basins decrease in age from south to north. In the south, the WNW Sylvania Mountain fault system initiated left-oblique motion after 7 Ma but does not have evidence of contemporary displacement. Farther north, the left-oblique motion on the Palmetto Mountain fault system initiated after 6.0 to 4.0 Ma and has well-developed scarps in Quaternary deposits. Cumulative left-lateral displacement for the Sylvania Mountain fault system is 10-15 km, and is 8-12 km for the Palmetto fault system. The NNE-striking faults that emanate from the left-oblique faults merge with NNW transcurrent faults farther north in the eastern part of the Mina deflection, which links the Owens Valley fault of eastern California to the central Walker Lane. Left-oblique displacement on the Sylvania Mountain and Palmetto Mountain fault zones deformed the Furnace Creek and Fish Lake Valley faults. Left-oblique motion on Sylvania Mountain fault deflected the FCF into the 15 km wide Cucomungo Canyon restraining bend, segmented the >3.0 km deep basin underlying southern Fish Lake Valley, and formed a 2 km wide restraining bend in the FLVF. Part of the left-oblique motion on the Palmetto Mountain fault zone crosses Fish Lake Valley and offsets the FLVF in a 3 km wide restraining bend with the remainder being taken-up by NNW structures along the eastern side of southern Fish Lake Valley.

Contemporary recent extension and compression in the central Andes

NASA Astrophysics Data System (ADS)

Tibaldi, A.; Bonali, F. L.

2018-02-01

Although extension in the high Andes vs. compression in the lowlands has already been widely discussed in the literature, for the first time we recognized both extensional and contractional structures that developed contemporaneously during late Pliocene-Quaternary times in a wide area of the central Andean chain (about 90,000 km2), where crustal earthquake data are missing. This area comprises north-eastern Chile, south-western Bolivia and north-western Argentina, and extends from the Puna Plateau to the Altiplano-volcanic belt. Late Pliocene-Quaternary folds, with hinge lines trending NNE-SSW to N-S, are mostly located along the westernmost part of the volcanic belt and the eastern part of the Western Cordillera. Locally, there are coeval reverse faults, parallel to the folds, which reach up to the surface; particularly, the Miscanti Ridge, Tolocha Fault and La Casualidad Ridge may be the morphostructural expression of tens-km-long fault-propagation folds, which locally show topographic scarps hundreds of meters high. North and east of the contractional structures, we found evidence of late Pliocene-Quaternary normal faults striking N-S in the southern part of the study area, and NW-SE in the northern part. Well-developed grabens are present in the higher areas of the volcanic belt and in the transition zone with the Puna Plateau. The surface rupture zones of normal fault swarms range 8-24 km in length, with single fault strands up to 18 km long, which are typical of tectonic structures. The distribution in space and time of the studied contractional and extensional structures indicates that they originated in the same time period; we thus address the challenging question regarding the possible origin of the stress sources, by analysing possible causes such as volcanotectonics, high topography, orogeny collapse, and gravitational spreading of the orogen, in relation also with the role played by inherited structures. We finally analyse the relations between the different structures and magma upwelling, and the potential for seismic hazard.

Variations in rupture process with recurrence interval in a repeated small earthquake

USGS Publications Warehouse

Vidale, J.E.; Ellsworth, W.L.; Cole, A.; Marone, Chris

1994-01-01

In theory and in laboratory experiments, friction on sliding surfaces such as rock, glass and metal increases with time since the previous episode of slip. This time dependence is a central pillar of the friction laws widely used to model earthquake phenomena. On natural faults, other properties, such as rupture velocity, porosity and fluid pressure, may also vary with the recurrence interval. Eighteen repetitions of the same small earthquake, separated by intervals ranging from a few days to several years, allow us to test these laboratory predictions in situ. The events with the longest time since the previous earthquake tend to have about 15% larger seismic moment than those with the shortest intervals, although this trend is weak. In addition, the rupture durations of the events with the longest recurrence intervals are more than a factor of two shorter than for the events with the shortest intervals. Both decreased duration and increased friction are consistent with progressive fault healing during the time of stationary contact.In theory and in laboratory experiments, friction on sliding surfaces such as rock, glass and metal increases with time since the previous episode of slip. This time dependence is a central pillar of the friction laws widely used to model earthquake phenomena. On natural faults, other properties, such as rupture velocity, porosity and fluid pressure, may also vary with the recurrence interval. Eighteen repetitions of the same small earthquake, separated by intervals ranging from a few days to several years, allow us to test these laboratory predictions in situ. The events with the longest time since the previous earthquake tend to have about 15% larger seismic moment than those with the shortest intervals, although this trend is weak. In addition, the rupture durations of the events with the longest recurrence intervals are more than a factor of two shorter than for the events with the shortest intervals. Both decreased duration and increased friction are consistent with progressive fault healing during the time of stationary contact.

Seismicity and seismogenic structures of Central Apennines (Italy): constraints on the present-day stress field from focal mechanisms - The SLAM (Seismicity of Lazio-Abruzzo and Molise) project

NASA Astrophysics Data System (ADS)

Frepoli, Alberto; Battista Cimini, Giovanni; De Gori, Pasquale; De Luca, Gaetano; Marchetti, Alessandro; Montuori, Caterina; Pagliuca, Nicola

2016-04-01

We present new results for the microseismic activity in the Central Apennines recorded from a total of 81seismic stations. The large number of recording sites derives from the combination of temporary and permanent seismic networks operating in the study region. Between January 2009 and October 2013 we recorded 6923 earthquakes with local magnitudes ML ranging from 0.1 to 4.8. We located hypocentres by using a refined 1D crustal velocity model. The majority of the hypocenters are located beneath the axes of the Apenninic chain, while the seismic activity observed along the peri-Tyrrhenian margin is lower. The seismicity extends to a depth of 32 km; the hypocentral depth distribution exhibits a pronounced peak of seismic energy release in the depth range between 8 and 20 km. During the observation period we recorded two major seismic swarms and one seismic sequence in the Marsica-Sorano area in which we have had the largest detected magnitude (ML = 4.8). Fault plane solutions for a total of 600 earthquakes were derived from P-polarities. This new data set consists of a number of focal plane solutions that is about four times the data so far available for regional stress field study. The majority of the focal mechanisms show predominantly normal fault solutions. T-axis trends are oriented NE-SW confirming that the area is in extension. We also derived the azimuths of the principal stress axes by inverting the fault plane solutions and calculated the direction of the maximum horizontal stress, which is mainly sub-vertical oriented. The study region has been historically affected by many strong earthquakes, some of them very destructive. This work can give an important contribution to the seismic hazard assessment in an area densely populated as the city of Rome which is distant around 60 km from the main seismogenic structures of Central Apennine.

New seismic sources parameterization in El Salvador. Implications to seismic hazard.

NASA Astrophysics Data System (ADS)

Alonso-Henar, Jorge; Staller, Alejandra; Jesús Martínez-Díaz, José; Benito, Belén; Álvarez-Gómez, José Antonio; Canora, Carolina

2014-05-01

El Salvador is located at the pacific active margin of Central America, here, the subduction of the Cocos Plate under the Caribbean Plate at a rate of ~80 mm/yr is the main seismic source. Although the seismic sources located in the Central American Volcanic Arc have been responsible for some of the most damaging earthquakes in El Salvador. The El Salvador Fault Zone is the main geological structure in El Salvador and accommodates 14 mm/yr of horizontal displacement between the Caribbean Plate and the forearc sliver. The ESFZ is a right lateral strike-slip fault zone c. 150 km long and 20 km wide .This shear band distributes the deformation among strike-slip faults trending N90º-100ºE and secondary normal faults trending N120º- N170º. The ESFZ is relieved westward by the Jalpatagua Fault and becomes less clear eastward disappearing at Golfo de Fonseca. Five sections have been proposed for the whole fault zone. These fault sections are (from west to east): ESFZ Western Section, San Vicente Section, Lempa Section, Berlin Section and San Miguel Section. Paleoseismic studies carried out in the Berlin and San Vicente Segments reveal an important amount of quaternary deformation and paleoearthquakes up to Mw 7.6. In this study we present 45 capable seismic sources in El Salvador and their preliminary slip-rate from geological and GPS data. The GPS data detailled results are presented by Staller et al., 2014 in a complimentary communication. The calculated preliminary slip-rates range from 0.5 to 8 mm/yr for individualized faults within the ESFZ. We calculated maximum magnitudes from the mapped lengths and paleoseismic observations.We propose different earthquakes scenario including the potential combined rupture of different fault sections of the ESFZ, resulting in maximum earthquake magnitudes of Mw 7.6. We used deterministic models to calculate acceleration distribution related with maximum earthquakes of the different proposed scenario. The spatial distribution of seismic accelerations are compared and calibrated using the February 13, 2001 earthquake, as control earthquake. To explore the sources of historical earthquakes we compare synthetic acceleration maps with the historical earthquakes of March 6, 1719 and June 8, 1917. control earthquake. To explore the sources of historical earthquakes we compare synthetic acceleration maps with the historical earthquakes of March 6, 1719 and June 8, 1917.

The Queen Charlotte-Fairweather Fault Zone - Geomorphology of a submarine transform fault, offshore British Columbia and southeastern Alaska

NASA Astrophysics Data System (ADS)

Walton, M. A. L.; Barrie, V.; Greene, H. G.; Brothers, D. S.; Conway, K.; Conrad, J. E.

2017-12-01

The Queen Charlotte-Fairweather (QC-FW) Fault Zone is the Pacific - North America transform plate boundary and is clearly seen for over 900 km on the seabed as a linear and continuous feature from offshore central Haida Gwaii, British Columbia to Icy Point, Alaska. Recently (July - September 2017) collected multibeam bathymetry, seismic-reflection profiles and sediment cores provide evidence for the continuous strike-slip morphology along the continental shelfbreak and upper slope, including a linear fault valley, offset submarine canyons and gullies, and right-step offsets (pull apart basins). South of central Haida Gwaii, the QC-FW is represented by several NW-SE to N-S trending faults to the southern end of the islands. Adjacent to the fault at the southern extreme and offshore Dixon Entrance (Canada/US boundary) are 400 to 600 m high mud volcanos in 1000 to 1600 m water depth that have plumes extending up 700 m into the water column and contain extensive carbonate crusts and chemosynthetic communities within the craters. In addition, gas plumes have been identified that appear to be directly associated with the fault zone. Surficial Quaternary sediments within and adjacent to the central and southern fault date either to the deglaciation of this region of the Pacific north coast (16,000 years BP) or to the last interstadial period ( 40,000 years BP). Sediment accumulation is minimal and the sediments cored are primarily hard-packed dense sands that appear to have been transported along the fault valley. The majority of the right-lateral slip along the entire QC-FW appears to be accommodated by the single fault north of the convergence at its southern most extent.

The Queen Charlotte-Fairweather Fault Zone - Geomorphology of a submarine transform fault, offshore British Columbia and southeastern Alaska

NASA Astrophysics Data System (ADS)

Walton, M. A. L.; Barrie, V.; Greene, H. G.; Brothers, D. S.; Conway, K.; Conrad, J. E.

2016-12-01

The Queen Charlotte-Fairweather (QC-FW) Fault Zone is the Pacific - North America transform plate boundary and is clearly seen for over 900 km on the seabed as a linear and continuous feature from offshore central Haida Gwaii, British Columbia to Icy Point, Alaska. Recently (July - September 2017) collected multibeam bathymetry, seismic-reflection profiles and sediment cores provide evidence for the continuous strike-slip morphology along the continental shelfbreak and upper slope, including a linear fault valley, offset submarine canyons and gullies, and right-step offsets (pull apart basins). South of central Haida Gwaii, the QC-FW is represented by several NW-SE to N-S trending faults to the southern end of the islands. Adjacent to the fault at the southern extreme and offshore Dixon Entrance (Canada/US boundary) are 400 to 600 m high mud volcanos in 1000 to 1600 m water depth that have plumes extending up 700 m into the water column and contain extensive carbonate crusts and chemosynthetic communities within the craters. In addition, gas plumes have been identified that appear to be directly associated with the fault zone. Surficial Quaternary sediments within and adjacent to the central and southern fault date either to the deglaciation of this region of the Pacific north coast (16,000 years BP) or to the last interstadial period ( 40,000 years BP). Sediment accumulation is minimal and the sediments cored are primarily hard-packed dense sands that appear to have been transported along the fault valley. The majority of the right-lateral slip along the entire QC-FW appears to be accommodated by the single fault north of the convergence at its southern most extent.

Geologic Map of the Nulato Quadrangle, West-Central Alaska

USGS Publications Warehouse

Patton, W.W.; Moll-Stalcup, E. J.

2000-01-01

Introduction The Nulato quadrangle encompasses approximately 17,000 km2 (6,500 mi2) of west-central Alaska within the Yukon River drainage basin. The quadrangle straddles two major geologic features-the Yukon-Koyukuk sedimentary basin, a huge triangle-shaped Cretaceous depression that stretches across western Alaska from the Brooks Range to the Yukon delta; and the Ruby geanticline,a broad uplift of pre-Cretaceous rocks that borders the Yukon-Koyukuk basin on the southeast. The Kaltag Fault crosses the quadrangle diagonally from northeast to southwest and dextrally offsets all major geologic features as much as 130 km.

Subsurface Constraints on Late Cenozoic Basin Geometry in Northern Fish Lake Valley and Displacement Transfer Along the Northern Fish Lake Valley Fault Zone, Western Nevada

NASA Astrophysics Data System (ADS)

Mueller, N.; Kerstetter, S. R.; Katopody, D. T.; Oldow, J. S.

2016-12-01

The NW-striking, right-oblique Fish Lake Valley fault zone (FLVFZ) forms the northern segment of the longest active structure in the western Great Basin; the Death Valley - Furnace Creek - Fish Lake Valley fault system. Since the mid-Miocene, 50 km of right-lateral displacement is documented on the southern FLVFZ and much of that displacement was and is transferred east and north on active WNW left-lateral faults. Prior to the Pliocene, displacement was transferred east and north on a low-angle detachment. Displacement on the northern part of the FLVFZ continues and is transferred to a fanned array of splays striking (west to east) WNW, NNW, ENE and NNE. To determine the displacement budget on these structures, we conducted a gravity survey to determine subsurface basin morphology and its relation to active faults. Over 2450 stations were collected and combined with existing PACES and proprietary data for a total of 3388 stations. The data were terrain corrected and reduced to a 2.67 g/cm3 density to produce a residual complete Bouguer anomaly. The eastern part of northern Fish Lake Valley is underlain by several prominent gravity lows forming several sub-basins with maximum RCBA values ranging from -24 to -28 mGals. The RCBA was inverted for depth using Geosoft Oasis Montaj GM-SYS 3D modeling software. Density values for the inversion were constrained by lithologic and density logs from wells that penetrate the entire Cenozoic section into the Paleozoic basement. Best fitting gravity measurements taken at the wellheads yielded an effective density of 2.4 g/cm3 for the basin fill. Modeled basement depths range between 2.1 to 3 km. The sub-basins form an arc opening to the NW and are bounded by ENE and NNE faults in the south and NS to NNW in the north. At the northern end of the valley, the faults merge with ENE left-lateral strike slip faults of the Mina deflection, which carries displacement to NW dextral strike-slip faults of the central Walker Lane.

Active strike-slip faulting in El Salvador, Central America

NASA Astrophysics Data System (ADS)

Corti, Giacomo; Carminati, Eugenio; Mazzarini, Francesco; Oziel Garcia, Marvyn

2005-12-01

Several major earthquakes have affected El Salvador, Central America, during the Past 100 yr as a consequence of oblique subduction of the Cocos plate under the Caribbean plate, which is partitioned between trench-orthogonal compression and strike-slip deformation parallel to the volcanic arc. Focal mechanisms and the distribution of the most destructive earthquakes, together with geomorphologic evidence, suggest that this transcurrent component of motion may be accommodated by a major strike-slip fault (El Salvador fault zone). We present field geological, structural, and geomorphological data collected in central El Salvador that allow the constraint of the kinematics and the Quaternary activity of this major seismogenic strike-slip fault system. Data suggest that the El Salvador fault zone consists of at least two main ˜E-W fault segments (San Vicente and Berlin segments), with associated secondary synthetic (WNW-ESE) and antithetic (NNW-SSE) Riedel shears and NW-SE tensional structures. The two main fault segments overlap in a dextral en echelon style with the formation of an intervening pull-apart basin. Our original geological and geomorphologic data suggest a late Pleistocene Holocene slip rate of ˜11 mm/yr along the Berlin segment, in contrast with low historical seismicity. The kinematics and rates of deformation suggested by our new data are consistent with models involving slip partitioning during oblique subduction, and support the notion that a trench-parallel component of motion between the Caribbean and Cocos plates is concentrated along E-W dextral strike-slip faults parallel to the volcanic arc.

Fault zone structure and inferences on past activities of the active Shanchiao Fault in the Taipei metropolis, northern Taiwan

NASA Astrophysics Data System (ADS)

Chen, C.; Lee, J.; Chan, Y.; Lu, C.

2010-12-01

The Taipei Metropolis, home to around 10 million people, is subject to seismic hazard originated from not only distant faults or sources scattered throughout the Taiwan region, but also active fault lain directly underneath. Northern Taiwan including the Taipei region is currently affected by post-orogenic (Penglai arc-continent collision) processes related to backarc extension of the Ryukyu subduction system. The Shanchiao Fault, an active normal fault outcropping along the western boundary of the Taipei Basin and dipping to the east, is investigated here for its subsurface structure and activities. Boreholes records in the central portion of the fault were analyzed to document the stacking of post- Last Glacial Maximum growth sediments, and a tulip flower structure is illuminated with averaged vertical slip rate of about 3 mm/yr. Similar fault zone architecture and post-LGM tectonic subsidence rate is also found in the northern portion of the fault. A correlation between geomorphology and structural geology in the Shanchiao Fault zone demonstrates an array of subtle geomorphic scarps corresponds to the branch fault while the surface trace of the main fault seems to be completely erased by erosion and sedimentation. Such constraints and knowledge are crucial in earthquake hazard evaluation and mitigation in the Taipei Metropolis, and in understanding the kinematics of transtensional tectonics in northern Taiwan. Schematic 3D diagram of the fault zone in the central portion of the Shanchiao Fault, displaying regional subsurface geology and its relation to topographic features.

Structural Inventory of Great Basin Geothermal Systems and Definition of Favorable Structural Settings

DOE Data Explorer

Faulds, James E.

2013-12-31

Over the course of the entire project, field visits were made to 117 geothermal systems in the Great Basin region. Major field excursions, incorporating visits to large groups of systems, were conducted in western Nevada, central Nevada, northwestern Nevada, northeastern Nevada, east‐central Nevada, eastern California, southern Oregon, and western Utah. For example, field excursions to the following areas included visits of multiple geothermal systems: - Northwestern Nevada: Baltazor Hot Spring, Blue Mountain, Bog Hot Spring, Dyke Hot Springs, Howard Hot Spring, MacFarlane Hot Spring, McGee Mountain, and Pinto Hot Springs in northwest Nevada. - North‐central to northeastern Nevada: Beowawe, Crescent Valley (Hot Springs Point), Dann Ranch (Hand‐me‐Down Hot Springs), Golconda, and Pumpernickel Valley (Tipton Hot Springs) in north‐central to northeast Nevada. - Eastern Nevada: Ash Springs, Chimney Hot Spring, Duckwater, Hiko Hot Spring, Hot Creek Butte, Iverson Spring, Moon River Hot Spring, Moorman Spring, Railroad Valley, and Williams Hot Spring in eastern Nevada. - Southwestern Nevada‐eastern California: Walley’s Hot Spring, Antelope Valley, Fales Hot Springs, Buckeye Hot Springs, Travertine Hot Springs, Teels Marsh, Rhodes Marsh, Columbus Marsh, Alum‐Silver Peak, Fish Lake Valley, Gabbs Valley, Wild Rose, Rawhide‐ Wedell Hot Springs, Alkali Hot Springs, and Baileys/Hicks/Burrell Hot Springs. - Southern Oregon: Alvord Hot Spring, Antelope Hot Spring‐Hart Mountain, Borax Lake, Crump Geyser, and Mickey Hot Spring in southern Oregon. - Western Utah: Newcastle, Veyo Hot Spring, Dixie Hot Spring, Thermo, Roosevelt, Cove Fort, Red Hill Hot Spring, Joseph Hot Spring, Hatton Hot Spring, and Abraham‐Baker Hot Springs. Structural controls of 426 geothermal systems were analyzed with literature research, air photos, google‐Earth imagery, and/or field reviews (Figures 1 and 2). Of the systems analyzed, we were able to determine the structural settings of more than 240 sites. However, we found that many “systems” consisted of little more than a warm or hot well in the central part of a basin. Such “systems” were difficult to evaluate in terms of structural setting in areas lacking in geophysical data. Developed database for structural catalogue in a master spreadsheet. Data components include structural setting, primary fault orientation, presence or absence of Quaternary faulting, reservoir lithology, geothermometry, presence or absence of recent magmatism, and distinguishing blind systems from those that have surface expressions. Reviewed site locations for all 426 geothermal systems– Confirmed and/or relocated spring and geothermal sites based on imagery, maps, and other information for master database. Many systems were mislocated in the original database. In addition, some systems that included several separate springs spread over large areas were divided into two or more distinct systems. Further, all hot wells were assigned names based on their location to facilitate subsequent analyses. We catalogued systems into the following eight major groups, based on the dominant pattern of faulting (Figure 1): - Major normal fault segments (i.e., near displacement maxima). - Fault bends. - Fault terminations or tips. - Step‐overs or relay ramps in normal faults. - Fault intersections. - Accommodation zones (i.e., belts of intermeshing oppositely dipping normal faults), - Displacement transfer zones whereby strike‐slip faults terminate in arrays of normal faults. - Transtensional pull‐aparts. These settings form a hierarchal pattern with respect to fault complexity. - Major normal faults and fault bends are the simplest. - Fault terminations are typically more complex than mid‐segments, as faults commonly break up into multiple strands or horsetail near their ends. - A fault intersection is generally more complex, as it generally contains both multiple fault strands and can include discrete di...

Structural Analysis and Evolution of the Kashan (Qom-Zefreh) Fault, Central Iran

NASA Astrophysics Data System (ADS)

Safaei, H.; Taheri, A.; Vaziri-Moghaddam, H.

The main objectives of this research were to identify the geometry and structure of the Qom-Zefreh fault and to determine the extent of its effects on stratigraphy and facies changes. The identification of movement mechanism of major faults in basement, extent and time of their activities are important effects for evaluation of paleogeography of the Iran plateau. In the Orumieh-Dokhtar volcanic band, there are nearly parallel faults to the Zagros Zone. These faults were formed during closure of the Neothetys and collision of the Arabic plate with crust of Iran. The Qom-Zefreh fault is one of these faults, which is known as having four different trend faults. The result indicates that, this fault is not divided in four segments with different trends but the major trend is of Central section, which is the Kashan segment with AZ140 trend and other segments are just related faults. Thus the name of the Kashan fault is recommended for this fault. The mechanism of the Kashan fault is dextral transpression and other related faults in the region are in good correlation with fractures in a dextral transpression system. The stratigraphic studies conducted on the present formations show the effect of fault movements in Upper Cretaceous sedimentary basin. Lack of noticeable changes in Lower Cretaceous sediments and before that indicates that, the fault system activity has been started from the Upper Cretaceous. Thus, based upon these results, the effect of the Neothetys sea closure in this region could be considered at least from the Upper Cretaceous.

Control spectra for Quito

NASA Astrophysics Data System (ADS)

Aguiar, Roberto; Rivas-Medina, Alicia; Caiza, Pablo; Quizanga, Diego

2017-03-01

The Metropolitan District of Quito is located on or very close to segments of reverse blind faults, Puengasí, Ilumbisí-La Bota, Carcelen-El Inca, Bellavista-Catequilla and Tangahuilla, making it one of the most seismically dangerous cities in the world. The city is divided into five areas: south, south-central, central, north-central and north. For each of the urban areas, elastic response spectra are presented in this paper, which are determined by utilizing some of the new models of the Pacific Earthquake Engineering Research Center (PEER) NGA-West2 program. These spectra are calculated considering the maximum magnitude that could be generated by the rupture of each fault segment, and taking into account the soil type that exists at different points of the city according to the Norma Ecuatoriana de la Construcción (2015). Subsequently, the recurrence period of earthquakes of high magnitude in each fault segment is determined from the physical parameters of the fault segments (size of the fault plane and slip rate) and the pattern of recurrence of type Gutenberg-Richter earthquakes with double truncation magnitude (Mmin and Mmax) is used.

Structural Evolution of central part of the Tuzgolu (Salt Lake) Basin, Central Anatolia, Turkey

NASA Astrophysics Data System (ADS)

Ada, M.; Cemen, I.; Çaptuğ, A.; Demirci, M.; Engin, C.

2017-12-01

The Tuzgolu Basin in Central Anatolia, Turkey, covers low-relief areas located between the Pontide Mountains to the North and Tauride Mountains to the South. The basin started to form as a rift basin during the Late Maastrichtian. The main Tuzgolu-Aksaray fault zone on the eastern margin of the basin and the northwest trending Yeniceoba and Cihanbeyli fault zones on the western margin of the basin were probably developed during that time. The basin has also experienced westward extension in response to westward escape of the Anatolian plate since Late Miocene. Several geologic studies have been conducted in the Tuz Gölü (Salt Lake) Basin and surrounding areas to determine structural and tectono-stratigraphic development of the basin. However, there are still many questions regarding the structural evolution of the basin. The main purpose of this study is to investigate the structural evolution of the central Tuzgolu Basin based on the structural interpretation of available 2-D seismic reflection profiles, well log analysis and construction of structural cross sections. The cross-sections will be based on depth converted seismic lines to determine structural geometry of the faults and folds. A preliminary Petrel project has been prepared using available seismic profiles. Our preliminary structural interpretations suggest that a well-developed rollover anticline was developed with respect to the westward extension in Central Anatolia. The rollover anticline is faulted in its crest area by both down-to-the west and down-to-the east normal faults. The geometry of the main boundary fault at depth still remains in question. We anticipate that this question will be resolved based on depth converted structural cross-sections and their restoration.

Moment tensor solutions for the Iberian-Maghreb region during the IberArray deployment (2009-2013)

NASA Astrophysics Data System (ADS)

Martín, R.; Stich, D.; Morales, J.; Mancilla, F.

2015-11-01

We perform regional moment tensor inversion for 84 earthquakes that occurred in the Iberian-Maghreb region during the second and third leg of IberArray deployment (2009-2013). During this period around 300 seismic broadband stations were operating in the area, reducing the interstation spacing to ~ 50 km over extended areas. We use the established processing sequence of the IAG moment tensor catalogue, increasing to 309 solutions with this update. New moment tensor solutions present magnitudes ranging from Mw 3.2 to 6.3 and source depths from 2 to 620 km. Most solutions correspond to Northern Algeria, where a compressive deformation pattern is consolidated. The Betic-Rif sector shows a progression of faulting styles from mainly shear faulting in the east via predominantly extension in the central sector to reverse and strike-slip faulting in the west. At the SW Iberia margin, the predominance of strike-slip and reverse faulting agrees with the expected transpressive character of the Eurasian-Nubia plate boundary. New strike-slip and oblique reverse solutions in the Trans-Alboran Shear Zone reflect its left-lateral regime. The most significant improvement corresponds to the Atlas Mountains and the surroundings of the Gibraltar Arc with scarce previous solutions. Reverse and strike-slip faulting solutions in the Atlas System display the accommodation of plate convergence by shortening in the belt. At the Gibraltar Arc, several new solutions were obtained at lower crustal and subcrustal depths. These mechanisms show substantial heterogeneity, covering the full range of faulting styles with highly variable orientations of principal stress axes, including opposite strike slip faulting solutions at short distance. The observations are not straightforward to explain by a simple geodynamic scenario and suggest the interplay of different processes, among them plate convergence in old oceanic lithospheric with large brittle thickness at the SW Iberia margin, as well as delamination of thickened continental lithosphere beneath the Betic-Rif arc.

Microstructural investigations on carbonate fault core rocks in active extensional fault zones from the central Apennines (Italy)

NASA Astrophysics Data System (ADS)

Cortinovis, Silvia; Balsamo, Fabrizio; Storti, Fabrizio

2017-04-01

The study of the microstructural and petrophysical evolution of cataclasites and gouges has a fundamental impact on both hydraulic and frictional properties of fault zones. In the last decades, growing attention has been payed to the characterization of carbonate fault core rocks due to the nucleation and propagation of coseismic ruptures in carbonate successions (e.g., Umbria-Marche 1997, L'Aquila 2009, Amatrice 2016 earthquakes in Central Apennines, Italy). Among several physical parameters, grain size and shape in fault core rocks are expected to control the way of sliding along the slip surfaces in active fault zones, thus influencing the propagation of coseismic ruptures during earthquakes. Nevertheless, the role of grain size and shape distribution evolution in controlling the weakening or strengthening behavior in seismogenic fault zones is still not fully understood also because a comprehensive database from natural fault cores is still missing. In this contribution, we present a preliminary study of seismogenic extensional fault zones in Central Apennines by combining detailed filed mapping with grain size and microstructural analysis of fault core rocks. Field mapping was aimed to describe the structural architecture of fault systems and the along-strike fault rock distribution and fracturing variations. In the laboratory we used a Malvern Mastersizer 3000 granulometer to obtain a precise grain size characterization of loose fault rocks combined with sieving for coarser size classes. In addition, we employed image analysis on thin sections to quantify the grain shape and size in cemented fault core rocks. The studied fault zones consist of an up to 5-10 m-thick fault core where most of slip is accommodated, surrounded by a tens-of-meters wide fractured damage zone. Fault core rocks consist of (1) loose to partially cemented breccias characterized by different grain size (from several cm up to mm) and variable grain shape (from very angular to sub-rounded), and (2) very fine-grained gouges (< 1 mm) localized along major and minor mirror-like slip surfaces. Damage zones mostly consist of fractured rocks and, locally, pulverized rocks. Collectively, field observations and laboratory analyses indicate that within the fault cores of the studied fault zones, grain size progressively decreases approaching the master slip surfaces. Furthermore, grain shape changes from very angular to sub-rounded clasts moving toward the master slip surfaces. These features suggest that the progressive evolution of grain size and shape distributions within fault cores may have determined the development of strain localization by the softening and cushioning effects of smaller particles in loose fault rocks.

The Quaternary thrust system of the northern Alaska Range

USGS Publications Warehouse

Bemis, Sean P.; Carver, Gary A.; Koehler, Richard D.

2012-01-01

The framework of Quaternary faults in Alaska remains poorly constrained. Recent studies in the Alaska Range north of the Denali fault add significantly to the recognition of Quaternary deformation in this active orogen. Faults and folds active during the Quaternary occur over a length of ∼500 km along the northern flank of the Alaska Range, extending from Mount McKinley (Denali) eastward to the Tok River valley. These faults exist as a continuous system of active structures, but we divide the system into four regions based on east-west changes in structural style. At the western end, the Kantishna Hills have only two known faults but the highest rate of shallow crustal seismicity. The western northern foothills fold-thrust belt consists of a 50-km-wide zone of subparallel thrust and reverse faults. This broad zone of deformation narrows to the east in a transition zone where the range-bounding fault of the western northern foothills fold-thrust belt terminates and displacement occurs on thrust and/or reverse faults closer to the Denali fault. The eastern northern foothills fold-thrust belt is characterized by ∼40-km-long thrust fault segments separated across left-steps by NNE-trending left-lateral faults. Altogether, these faults accommodate much of the topographic growth of the northern flank of the Alaska Range.Recognition of this thrust fault system represents a significant concern in addition to the Denali fault for infrastructure adjacent to and transecting the Alaska Range. Although additional work is required to characterize these faults sufficiently for seismic hazard analysis, the regional extent and structural character should require the consideration of the northern Alaska Range thrust system in regional tectonic models.

Geologic Map of the Denver West 30' x 60' Quadrangle, North-Central Colorado

USGS Publications Warehouse

Kellogg, Karl S.; Shroba, Ralph R.; Bryant, Bruce; Premo, Wayne R.

2008-01-01

The Denver West quadrangle extends east-west across the entire axis of the Front Range, one of numerous uplifts in the Rocky Mountain region in which Precambrian rocks are exposed. The history of the basement rocks in the Denver West quadrangle is as old as 1,790 Ma. Along the east side of the range, a sequence of sedimentary rocks as old as Pennsylvanian, but dominated by Cretaceous-age rocks, overlies these ancient basement rocks and was upturned and locally faulted during Laramide (Late Cretaceous to early Tertiary) uplift of the range. The increasingly coarser grained sediments up section in rocks of latest Cretaceous to early Tertiary age record in remarkable detail this Laramide period of mountain building. On the west side of the range, a major Laramide fault (Williams Range thrust) places Precambrian rocks over Cretaceous sedimentary rocks. The geologic history of the quadrangle, therefore, can be divided into four major periods: (1) Proterozoic history, (2) Pennsylvanian to pre-Laramide, Late Cretaceous history, (3) Late Cretaceous to early Tertiary Laramide mountain building, and (4) post-Laramide history. In particular, the Quaternary history of the Denver West quadrangle is described in detail, based largely on extensive new mapping.

GPS and seismic constraints on the M = 7.3 2009 Swan Islands earthquake: implications for stress changes along the Motagua fault and other nearby faults

NASA Astrophysics Data System (ADS)

Graham, Shannon E.; DeMets, Charles; DeShon, Heather R.; Rogers, Robert; Maradiaga, Manuel Rodriguez; Strauch, Wilfried; Wiese, Klaus; Hernandez, Douglas

2012-09-01

We use measurements at 35 GPS stations in northern Central America and 25 seismometers at teleseismic distances to estimate the distribution of slip, source time function and Coulomb stress changes of the Mw = 7.3 2009 May 28, Swan Islands fault earthquake. This event, the largest in the region for several decades, ruptured the offshore continuation of the seismically hazardous Motagua fault of Guatemala, the site of the destructive Ms = 7.5 earthquake in 1976. Measured GPS offsets range from 308 millimetres at a campaign site in northern Honduras to 6 millimetres at five continuous sites in El Salvador. Separate inversions of geodetic and seismic data both indicate that up to ˜1 m of coseismic slip occurred along a ˜250-km-long rupture zone between the island of Roatan and the eastern limit of the 1976 M = 7.5 Motagua fault earthquake in Guatemala. Evidence for slip ˜250 km west of the epicentre is corroborated independently by aftershocks recorded by a local seismic network and by the high concentration of damage to structures in areas of northern Honduras adjacent to the western limit of the rupture zone. Coulomb stresses determined from the coseismic slip distribution resolve a maximum of 1 bar of stress transferred to the seismically hazardous Motagua fault and further indicate unclamping of normal faults along the northern shore of Honduras, where two M > 5 normal-faulting earthquakes and numerous small earthquakes were triggered by the main shock.

Orogen-scale uplift in the central Italian Apennines drives episodic behaviour of earthquake faults

PubMed Central

Cowie, P. A.; Phillips, R. J.; Roberts, G. P.; McCaffrey, K.; Zijerveld, L. J. J.; Gregory, L. C.; Faure Walker, J.; Wedmore, L. N. J.; Dunai, T. J.; Binnie, S. A.; Freeman, S. P. H. T.; Wilcken, K.; Shanks, R. P.; Huismans, R. S.; Papanikolaou, I.; Michetti, A. M.; Wilkinson, M.

2017-01-01

Many areas of the Earth’s crust deform by distributed extensional faulting and complex fault interactions are often observed. Geodetic data generally indicate a simpler picture of continuum deformation over decades but relating this behaviour to earthquake occurrence over centuries, given numerous potentially active faults, remains a global problem in hazard assessment. We address this challenge for an array of seismogenic faults in the central Italian Apennines, where crustal extension and devastating earthquakes occur in response to regional surface uplift. We constrain fault slip-rates since ~18 ka using variations in cosmogenic 36Cl measured on bedrock scarps, mapped using LiDAR and ground penetrating radar, and compare these rates to those inferred from geodesy. The 36Cl data reveal that individual faults typically accumulate meters of displacement relatively rapidly over several thousand years, separated by similar length time intervals when slip-rates are much lower, and activity shifts between faults across strike. Our rates agree with continuum deformation rates when averaged over long spatial or temporal scales (104 yr; 102 km) but over shorter timescales most of the deformation may be accommodated by <30% of the across-strike fault array. We attribute the shifts in activity to temporal variations in the mechanical work of faulting. PMID:28322311

Orogen-scale uplift in the central Italian Apennines drives episodic behaviour of earthquake faults.

PubMed

Cowie, P A; Phillips, R J; Roberts, G P; McCaffrey, K; Zijerveld, L J J; Gregory, L C; Faure Walker, J; Wedmore, L N J; Dunai, T J; Binnie, S A; Freeman, S P H T; Wilcken, K; Shanks, R P; Huismans, R S; Papanikolaou, I; Michetti, A M; Wilkinson, M

2017-03-21

Many areas of the Earth's crust deform by distributed extensional faulting and complex fault interactions are often observed. Geodetic data generally indicate a simpler picture of continuum deformation over decades but relating this behaviour to earthquake occurrence over centuries, given numerous potentially active faults, remains a global problem in hazard assessment. We address this challenge for an array of seismogenic faults in the central Italian Apennines, where crustal extension and devastating earthquakes occur in response to regional surface uplift. We constrain fault slip-rates since ~18 ka using variations in cosmogenic 36 Cl measured on bedrock scarps, mapped using LiDAR and ground penetrating radar, and compare these rates to those inferred from geodesy. The 36 Cl data reveal that individual faults typically accumulate meters of displacement relatively rapidly over several thousand years, separated by similar length time intervals when slip-rates are much lower, and activity shifts between faults across strike. Our rates agree with continuum deformation rates when averaged over long spatial or temporal scales (10 4  yr; 10 2  km) but over shorter timescales most of the deformation may be accommodated by <30% of the across-strike fault array. We attribute the shifts in activity to temporal variations in the mechanical work of faulting.

The central branch of the North Anatolian Fault In The Southern Marmara Sea: Evidence for a distributed, Holocene-active fault system

NASA Astrophysics Data System (ADS)

Barın, Burcu; Okay, Seda; Çifçi, Günay; Dondurur, Derman; Cormier, Marie Helene; Sorlien, Christopher; Meriç İlkimen, Elif

2015-04-01

The North Anatolian Fault (NAF) is a major right-lateral transform fault in northern Turkey that branches westward into several strands in the vicinity of the Sea of Marmara. The main northern branch bisects the Marmara Sea from east to west, and seismic reflection profiles acquired over the past 15 years have revealed its complex geometry. Further, the several basins that developed along that branch record stratigraphic sequences that provide the needed framework to interpret the relative timing of tectonic deformation in the Marmara Sea. In contrast, the central branch, which snakes across the shallow southern shelf of the Marmara Sea, has been much less investigated. Here, we analyze a comprehensive dataset of high-resolution multi-channel, sparker, and CHIRP seismic profiles, which were collected with the facilities of Seismic Laboratory (SeisLab) in the Institute of Marine Sciences and Technology and R/V K. Piri Reis belonging to Dokuz Eylül University, along the central branch in 2008 (TAMAM expedition) and in 2013-2014 (SoMAR expedition), within the framework of a bilateral TÜBİTAK - NSF project. In combination with other existing seismic profiles, these new data reveal that the Central Branch consists of multiple faults strands that are distributed across the broad southern shelf. They also reveal that many of these strands are Holocene-active, although they slip at slower rates than the northern branch and are associated with slower basin subsidence or local uplift. Lastly, seismic data image a system of half-grabens across the southern shelf that are associated with the strands of the central branch. Strata within these half-grabens are progressively tilted and consistently dip to the south. Further analysis will be conducted to determine whether the formation of these grabens are controlled by oblique slip on the strands of the central branch, or by slip on detachment faults beneath the southern shelf.

High-Precision Locations and the Stress Field from Instrumental Seismicity, Moment Tensors, and Short-Period Mechanisms through the Mina Deflection, Central Walker Lane

NASA Astrophysics Data System (ADS)

Ruhl, C. J.; Smith, K. D.

2012-12-01

The Mina Deflection (MD) region of the central Walker Lane of eastern California and western Nevada, is a complex zone of northeast-trending normal, and primarily left-lateral strike-slip to oblique-slip faulting that separates the Southern Walker Lane (SWL) from a series of east-tilted normal fault blocks in the Central Walker Lane (CWL) (Faulds and Henry, 2008; Surpless, 2008). The MD accommodates the transfer of right-lateral strike-slip motion from northwest-striking faults in the SWL to a series of left-stepping northwest-striking right-lateral strike-slip faults in the CWL, east of the Wassuk Range near Hawthorne, NV. The ~50 km wide ~80 km long right-step is a distinct transition in regional physiography that has been attributed to strain accommodation through pre-Cenozoic lithospheric structures. Several slip transfer mechanisms have been proposed within the MD, from clockwise rotation of high-angle fault blocks (Wesnousky, 2005), to low-angle displacement within the Silver Peak-Lone Mountain complex (Oldow et al., 2001), and curved fault arrays associated with localized basins and tectonic depressions (Ferranti et al., 2009). The region has been a regular source of M4+ events, the most recent being an extended sequence that included twenty-seven M 3.5+ earthquakes (largest event M 4.6) south of Hawthorne in 2011. These earthquakes (< 5 km depth) define shallow W-dipping (dip ~56°) and NW-dipping (dip ~70°) normal faulting constrained by moment tensor (MT) solutions and earthquake relocations. Temporary stations deployed in the source area provide good control. A distributed sequence in 2004, between Queen Valley and Mono Lake, primarily associated with the Huntoon Valley fault, included three M 5+ left-lateral strike-slip faulting events. A 1997 sequence in northern Fish Lake Valley (east of the White Mountains), with mainshock Mw 5.3 (Ichinose et al., 2003), also showed high-angle northeast-striking left-lateral strike-slip motion. Historical events include the 1934 M 6.5 Excelsior Mountains event south of Mina, NV, and the 1932 M 7.1 Cedar Mountains earthquake east of the Pilot Mountains. Another persistent feature in the seismicity is an ~40 km long arcuate distribution of activity extending from approximately Queen Valley, north of the White Mountains, to Mono Lake that appears to reflect a southwestern boundary to northeast-striking structures in the MD. Here we develop high-precision relocations of instrumental seismicity in the MD from 1984 through 2012, including relocations of the 2004 sequence, and account for the historical seismic record. MT solutions from published reports and computed from recent M 3.5+ earthquakes as well as available and developed short-period focal mechanisms are compiled to evaluate the stress field to assess mechanisms of slip accommodation. Based on the complex distribution of fault orientations, the stress field varies locally northward from the SWL throughout the MD; however, in many cases, fault plane alignments can be isolated from high-precision locations, providing better constraints on stress and slip orientations.

Along strike variation of active fault arrays and their effect on landscape morphology of the northwestern Himalaya

NASA Astrophysics Data System (ADS)

Nennewitz, Markus; Thiede, Rasmus; Bookhagen, Bodo

2017-04-01

The location and magnitude of the active deformation of the Himalaya has been debated for decades, but several aspects remain unknown. For instance, the spatial distribution of the deformation and the shortening that ultimately sustains Himalayan topography and the activity of major fault zones are not well constrained neither for the present day and nor for Holocene and Quarternary timescales. Because of these weakly constrained factors, many previous studies have assumed that the structural setting and the fault geometry of the Himalaya is continuous along strike and similar to fault geometries of central Nepal. Thus, the sub-surface structural information from central Nepal have been projected along strike, but have not been verified at other locations. In this study we use digital topographic analysis of the NW Himalaya. We obtained catchment-averaged, normalized steepness indexes of longitudinal river profiles with drainage basins ranging between 5 and 250km2 and analyzed the relative change in their spatial distribution both along and across strike. More specific, we analyzed the relative changes of basins located in the footwall and in the hanging wall of major fault zones. Under the assumption that along strike changes in the normalized steepness index are primarily controlled by the activity of thrust segments, we revealed new insights in the tectonic deformation and uplift pattern. Our results show three different segments along the northwest Himalaya, which are located, from east to west, in Garwhal, Chamba and Kashmir Himalaya. These have formed independent orogenic segments characterized by significant changes in their structural architecture and fault geometry. Moreover, their topographic changes indicate strong variations on fault displacement rates across first-order fault zones. With the help of along- and across-strike profiles, we were able to identify fault segments of pronounced fault activity across MFT, MBT, and the PT2 and identify the location of along strike changes which are interpreted as their segment boundaries. In addition to the steepness indices we use the accumulation of elevation data as a proxy for the strain that has been accumulated over a specific distance. Thus, despite the changes in topography, structural setting, and kinematics along the NW Himalaya we observe that the topography of the orogen is in good agreement with recently measured convergence rates obtained from GPS campaigns. These data suggest reduced crustal shortening towards the northwest. Deformation in the Central Himalaya has been explained either by in-sequence thrusting along the MFT that localize the entire Holocene shortening or a combination of this with out-of-sequence thrusting in the vicinity of the PT2. In contrast to these conceptual models, we propose that the segmented NW Himalaya is a product of the synchronous activity of different fault segments, accommodating the crustal shortening along three independently deforming organic segments. The lateral discontinuity of these segments is responsible for the accommodation of the variation in the deformation and the maintenance of the topography of the Himalaya in NW India.

Earthquake geology and paleoseismology of major strands of the San Andreas fault system: Chapter 38

USGS Publications Warehouse

Rockwell, Thomas; Scharer, Katherine M.; Dawson, Timothy E.

2016-01-01

The San Andreas fault system in California is one of the best-studied faults in the world, both in terms of the long-term geologic history and paleoseismic study of past surface ruptures. In this paper, we focus on the Quaternary to historic data that have been collected from the major strands of the San Andreas fault system, both on the San Andreas Fault itself, and the major subparallel strands that comprise the plate boundary, including the Calaveras-Hayward- Rogers Creek-Maacama fault zone and the Concord-Green Valley-Bartlett Springs fault zone in northern California, and the San Jacinto and Elsinore faults in southern California. The majority of the relative motion between the Pacific and North American lithospheric plates is accommodated by these faults, with the San Andreas slipping at about 34 mm/yr in central California, decreasing to about 20 mm/yr in northern California north of its juncture with the Calaveras and Concord faults. The Calaveras-Hayward-Rogers Creek-Maacama fault zone exhibits a slip rate of 10-15 mm/yr, whereas the rate along the Concord-Green Valley-Bartlett Springs fault zone is lower at about 5 mm/yr. In southern California, the San Andreas exhibits a slip rate of about 35 mm/yr along the Mojave section, decreasing to as low as 10-15 mm/yr along its juncture with the San Jacinto fault, and about 20 mm/yr in the Coachella Valley. The San Jacinto and Elsinore fault zones exhibit rates of about 15 and 5 mm/yr, respectively. The average recurrence interval for surface-rupturing earthquakes along individual elements of the San Andreas fault system range from 100-500 years and is consistent with slip rate at those sites: higher slip rates produce more frequent or larger earthquakes. There is also evidence of short-term variations in strain release (slip rate) along various fault sections, as expressed as “flurries” or clusters of earthquakes as well as periods of relatively fewer surface ruptures in these relatively short records. This is reflected by non-periodic coefficients of variation in earthquake recurrence of 0.4 to 0.7 for the various paleoseismic sites.

Model-Based Data Integration and Process Standardization Techniques for Fault Management: A Feasibility Study

NASA Technical Reports Server (NTRS)

Haste, Deepak; Ghoshal, Sudipto; Johnson, Stephen B.; Moore, Craig

2018-01-01

This paper describes the theory and considerations in the application of model-based techniques to assimilate information from disjoint knowledge sources for performing NASA's Fault Management (FM)-related activities using the TEAMS® toolset. FM consists of the operational mitigation of existing and impending spacecraft failures. NASA's FM directives have both design-phase and operational-phase goals. This paper highlights recent studies by QSI and DST of the capabilities required in the TEAMS® toolset for conducting FM activities with the aim of reducing operating costs, increasing autonomy, and conforming to time schedules. These studies use and extend the analytic capabilities of QSI's TEAMS® toolset to conduct a range of FM activities within a centralized platform.

Postobductional extension along and within the Frontal Range of the Eastern Oman Mountains

NASA Astrophysics Data System (ADS)

Mattern, Frank; Scharf, Andreas

2018-04-01

The Oman Mountains formed by late Cretaceous obduction of the Tethys-derived Semail Ophiolite. This study concerns the postobductional extension on the northern flank of the mountain belt. Nine sites at the northern margins of the Jabal Akhdar/Nakhl and Saih Hatat domes of the Eastern Oman ("Hajar") Mountains were investigated. The northern margins are marked by a system of major interconnected extensional faults, the "Frontal Range Fault". While the vertical displacements along the Saih Hatat and westerly located Jabal Nakhl domes measure 2.25-6.25 km, 0.5-4.5 km and 4-7 km, respectively, it amounts to 1-5 km along the Jabal Akhdar Dome. Extension had started during the late Cretaceous, towards the end of ophiolite emplacement. Two stages of extension can be ascertained (late Cretaceous to early Eocene and probably Oligocene) at the eastern part of the Frontal Range Fault System (Wadi Kabir and Fanja Graben faults of similar strike). Along the intervening and differently striking fault segments at Sad and Sunub the same two stages of deformation are deduced. The first stage is characterized again by extension. The second stage is marked by dextral motion, including local transtension. Probable Oligocene extension affected the Batinah Coast Fault while it also affected the Wadi Kabir Fault and the Fanja Graben. It is unclear whether the western portion of the Frontal Range Fault also went through two stages of deformation. Bedding-parallel ductile and brittle deformation is a common phenomenon. Hot springs and listwaenite are associated with dextral releasing bends within the fault system, as well as a basalt intrusion of probable Oligocene age. A structural transect through the Frontal Range along the superbly exposed Wadi Bani Kharous (Jabal Akhdar Dome) revealed that extension affected the Frontal Range at least 2.5 km south of the Frontal Range Fault. Also here, bedding-parallel shearing is important, but not exclusive. A late Cretaceous thrust was extensionally reactivated by a branch fault of the Frontal Range Fault. Extension may be ductile (limestone mylonites), ductile and brittle (ooid deformation, boudinaged belemnite rostra, shear bands) or brittle. Extension is heterogeneously distributed within the Frontal Range. Extension is mainly related to orogenic/gravitational collapse of the Oman Mountains. Collapse may have been associated with isostatic rebound and rise of the two domes. In the western part of the study area, the Frontal Range Fault has a listric morphology. It is probably horizontal at a depth of 15 km below the Batinah coastal area. The fault seems to use the clay- and tuff-bearing Aruma Group as shear horizon. The depth of 15 km may coincide with the brittle-ductile transition of quartz- and feldspar-rich rocks. Close to this depth, the listric Batinah Coast Fault curves into the Frontal Range Fault. Extension along the Frontal Range and Batinah Coast faults probably reactivated preexisting late Cretaceous thrust faults during post-late Eocene time. The latter fault is likely mechanically related to the Wadi Kabir Fault via the Fanja Graben Fault and the Sunub fault segment. Listwaenite and serpentinite cluster preferably around the extensional faults. The Semail Gap probably functioned as a sinistral transform fault or fault zone during the Permian.

Method to Determine Appropriate Source Models of Large Earthquakes Including Tsunami Earthquakes for Tsunami Early Warning in Central America

NASA Astrophysics Data System (ADS)

Tanioka, Yuichiro; Miranda, Greyving Jose Arguello; Gusman, Aditya Riadi; Fujii, Yushiro

2017-08-01

Large earthquakes, such as the Mw 7.7 1992 Nicaragua earthquake, have occurred off the Pacific coasts of El Salvador and Nicaragua in Central America and have generated distractive tsunamis along these coasts. It is necessary to determine appropriate fault models before large tsunamis hit the coast. In this study, first, fault parameters were estimated from the W-phase inversion, and then an appropriate fault model was determined from the fault parameters and scaling relationships with a depth dependent rigidity. The method was tested for four large earthquakes, the 1992 Nicaragua tsunami earthquake (Mw7.7), the 2001 El Salvador earthquake (Mw7.7), the 2004 El Astillero earthquake (Mw7.0), and the 2012 El Salvador-Nicaragua earthquake (Mw7.3), which occurred off El Salvador and Nicaragua in Central America. The tsunami numerical simulations were carried out from the determined fault models. We found that the observed tsunami heights, run-up heights, and inundation areas were reasonably well explained by the computed ones. Therefore, our method for tsunami early warning purpose should work to estimate a fault model which reproduces tsunami heights near the coast of El Salvador and Nicaragua due to large earthquakes in the subduction zone.

Implications for stress changes along the Motagua fault and other nearby faults using GPS and seismic constraints on the M=7.3 2009 Swan Islands earthquake

NASA Astrophysics Data System (ADS)

Graham, S. E.; Rodriguez, M.; Rogers, R. D.; Strauch, W.; Hernandez, D.; Demets, C.

2010-12-01

The May 28, 2009 M=7.3 Swan Islands earthquake off the north coast of Honduras caused significant damage in the northern part of the country, including seven deaths. This event, the largest in the region for several decades, ruptured the offshore continuation of the Motagua-Polochic fault system, whose 1976 earthquake (located several hundred kilometers to the southwest of the 2009 epicenter) caused more than 23,000 deaths in Central America and left homeless 20% of Guatemala’s population. We use elastic half-space modeling of coseismic offsets measured at 39 GPS stations in Honduras, El Salvador, and Guatemala to better understand the slip source of the recent Swan Islands earthquake. Measured offsets range from .32 meters at a campaign site near the Motagua fault in northern Honduras to 4 millimeters at five continuous sites in El Salvador. Coulomb stress calculations based on the estimated distribution of coseismic slip will be presented and compared to earthquake focal mechanisms and aftershock locations determined from a portable seismic network that was installed in northern Honduras after the main shock. Implications of the Swan Islands rupture for the seismically hazardous Motagua-Polochic fault system will be described.

Structure of a normal seismogenic fault zone in carbonates: The Vado di Corno Fault, Campo Imperatore, Central Apennines (Italy)

NASA Astrophysics Data System (ADS)

Demurtas, Matteo; Fondriest, Michele; Balsamo, Fabrizio; Clemenzi, Luca; Storti, Fabrizio; Bistacchi, Andrea; Di Toro, Giulio

2016-09-01

The Vado di Corno Fault Zone (VCFZ) is an active extensional fault cutting through carbonates in the Italian Central Apennines. The fault zone was exhumed from ∼2 km depth and accommodated a normal throw of ∼2 km since Early-Pleistocene. In the studied area, the master fault of the VCFZ dips N210/54° and juxtaposes Quaternary colluvial deposits in the hangingwall with cataclastic dolostones in the footwall. Detailed mapping of the fault zone rocks within the ∼300 m thick footwall-block evidenced the presence of five main structural units (Low Strain Damage Zone, High Strain Damage Zone, Breccia Unit, Cataclastic Unit 1 and Cataclastic Unit 2). The Breccia Unit results from the Pleistocene extensional reactivation of a pre-existing Pliocene thrust. The Cataclastic Unit 1 forms a ∼40 m thick band lining the master fault and recording in-situ shattering due to the propagation of multiple seismic ruptures. Seismic faulting is suggested also by the occurrence of mirror-like slip surfaces, highly localized sheared calcite-bearing veins and fluidized cataclasites. The VCFZ architecture compares well with seismological studies of the L'Aquila 2009 seismic sequence (mainshock MW 6.1), which imaged the reactivation of shallow-seated low-angle normal faults (Breccia Unit) cut by major high-angle normal faults (Cataclastic Units).

Hematite (U-Th)/He thermochronometry constrains intraplate strike-slip faulting on the Kuh-e-Faghan Fault, central Iran

NASA Astrophysics Data System (ADS)

Calzolari, Gabriele; Rossetti, Federico; Ault, Alexis K.; Lucci, Federico; Olivetti, Valerio; Nozaem, Reza

2018-03-01

The Kuh-e-Faghan strike-slip fault system (KFF), located to the northern edge of the Lut Block in central Iran, developed through a Neogene-Quaternary pulsed history of eastward fault propagation and fault-related exhumation. This system is a consequence of the residual stresses transmitted from the Arabia-Eurasia convergent plate boundary. Here we integrate structural and textural analysis with new and previously published apatite fission-track (AFT) and apatite (U-Th)/He (apatite He) results, chlorite thermomentry, and hematite (U-Th)/He data from hematite-coated brittle fault surfaces to constrain the timing of tectonic activity and refine patterns of late Miocene-Pliocene burial and exhumation associated with the propagation of the KFF. Twenty-nine hematite (U-Th)/He (hematite He) dates from three striated hematite coated slip surfaces from the KFF fault core and damage zone yield individual dates from 12-2 Ma. Petrographic analysis and chlorite thermometry of a polyphase, fossil fluid system in the KFF fault core document that fluid circulation and mineralization transitioned from a closed system characterized by pressure solution and calcite growth to an open system characterized by hot hydrothermal (T = 239 ± 10 °C) fluids and hematite formation. Hematite microtextures and grain size analysis reveal primary and secondary syntectonic hematite fabrics, no evidence of hematite comminution and similar hematite He closure temperatures ( 60-85 °C) in each sample. Integration of these results with thermal history modeling of AFT and apatite He data shows that KFF activity in the late Miocene is characterized by an early stage of fault nucleation, fluid circulation, hematite mineralization, and eastward propagation not associated with vertical movement that lasted from 12 to 7 Ma. Hematite He, AFT, and apatite He data track a second phase of fault system activity involving fault-related exhumation initiating at 7 Ma and continuing until present time. Our new data constrain the onset of the recognized Late Miocene-Pliocene tectonic reorganization in north-central Iran.

Quantifying strain partitioning between magmatic and amagmatic portions of the Afar triple junction of Ethiopia and Djibouti through use of contemporary and late Quaternary extension rates

NASA Astrophysics Data System (ADS)

Polun, S. G.; Hickcox, K.; Tesfaye, S.; Gomez, F. G.

2016-12-01

The central Afar rift in Ethiopia and Djibouti is a zone of accommodation between the onshore propagations of the Gulf of Aden and Red Sea oceanic spreading centers forming part of the Afar triple junction that divides the Arabia, Nubia, and Somalia plates. While extension in the onshore magmatic propagators is accommodated through magmatism and associated faulting, extension in the central Afar is accommodated solely by large and small faults. The contributions of these major faults to the overall strain budget can be well characterized, but smaller faults are more difficult to quantify. Sparse GPS data covering the region constrain the total extension budget across the diffuse triple junction zone. Late Quaternary slip rates for major faults in Hanle, Dobe, Guma, and Immino grabens were estimated using the quantitative analysis of faulted landforms. This forms a nearly complete transect from the onshore propagation of the Red Sea rift in Tendaho graben and the onshore propagation of the Gulf of Aden rift at Manda Inakir. Field surveying was accomplished using a combination of electronic distance measurer profiling and low altitude aerial surveying. Age constraints are provided from the Holocene lacustrine history or through terrestrial cosmogenic nuclide (TCN) dating of the faulted geomorphic surface. Along this transect, late Quaternary slip rates of major faults appear to accommodate 25% of the total horizontal stretching rate between the southern margin of Tendaho graben and the Red Sea coast, as determined from published GPS velocities. This constrains the proportion of total extension between Nubia and Arabia that is accommodated through major faulting in the central Afar, compared to the magmatism and associated faulting of the magmatic propagators elsewhere in the triple junction. Along the transect, individual fault slip rates decrease from the southeast to the northwest, suggesting a `Crank-Arm' model may be more applicable to explain the regional kinematics and the evolution of the triple junction.

Evidence for Strong Controls from Preexisting Structures on Border Fault Development and Basin Evolution in the Malawi Rift from 3D Lacustrine Refraction Data

NASA Astrophysics Data System (ADS)

Accardo, N. J.; Shillington, D. J.; Gaherty, J. B.; Scholz, C. A.; Ebinger, C.; Nyblade, A.; McCartney, T.; Chindandali, P. R. N.; Kamihanda, G.; Ferdinand-Wambura, R.

2017-12-01

A long-standing debate surrounds controls on the development and ultimately abandonment of basin bounding border faults. The Malawi Rift in the the Western Branch of the East African Rift System presents an ideal location to investigate normal fault development. The rift is composed of a series of half graben basins bound by large border faults, which cross several terranes and pre-existing features. To delineate rift basin structure, we undertook 3D first arrival tomography across the North and Central basins of the Malawi Rift based on seismic refraction data acquired in Lake Malawi. The resulting 3D velocity model allows for the first-ever mapping of 3D basin structure in the Western Branch of the EAR. We estimate fault displacement profiles along the two border faults and find that each accommodated 7.2 km of throw. Previous modeling studies suggest that given the significant lengths (>140 km) and throws of these faults, they may be nearing their maximum dimensions or may have already been abandoned. While both faults accommodate similar throws, their lengths differ by 40 km, likely due to the influence of both preexisting basement fabric and large-scale preexisting structures crossing the rift. Over 4 km of sediment exists where the border faults overlap in the accommodation zone indicating that these faults likely established their lengths early. Portions of both basins contain packages of sediment with anomalously fast velocities (> 4 km/s), which we interpret to represent sediment packages from prior rifting episodes. In the Central Basin, this preexisting sediment traces along the inferred offshore continuation of the Karoo-aged Ruhuhu Basin that intersects Lake Malawi at the junction between the North and Central basins. This feature may have influenced the length of the border fault bounding the Central Basin. In the North Basin, the preexisting sediment is thicker ( 4 km) and likely represents the offshore continuation of a series of preexisting rift basins that extend from the Malawi Rift north to the Rukwa Rift. The presence of this offshore basin confirms that the corridor between the Rukwa and Malawi Rifts has experienced prolonged periods of extension, likely thinning the lithosphere there, and thus providing a mechanism for focusing of long-lived magmatism at the Rungwe Volcanic Center.

Paleomagnetism and tectonic rotation of the lower Miocene Peach Springs Tuff: Colorado Plateau, Arizona, to Barstow, California

USGS Publications Warehouse

Wells, Ray E.; Hillhouse, John W.

1989-01-01

We have determined remanent magnetization directions of the lower Miocene Peach Springs Tuff at 41 localities in western Arizona and southeastern California. An unusual northeast and shallow magnetization direction confirms the proposed geologic correlation of isolated outcrops of the tuff from the Colorado Plateau to Barstow, California, a distance of 350 km. The Peach Springs Tuff was apparently emplaced as a single cooling unit about 18 or 19 Ma and is now exposed in 4 tectonic provinces west of the Plateau, including the Transition Zone, Basin and Range, Colorado River extensional corridor, and central Mojave Desert strike-slip zone. As such, the tuff is an ideal stratigraphic and structural marker for paleomagnetic assessment of regional variations in tectonic rotations about vertical axes. From 4 sites on the stable Colorado Plateau, we have determined a reference direction of remanent magnetization (I = 36.4°, D = 33.0°, α95 = 3.4°) that we interpret as a representation of the ambient magnetic field at the time of eruption. A steeper direction of magnetization (I = 54.8°, D = 22.5°, α95 = 2.3°) was observed at Kingman where the tuff is more than 100 m thick, and similar directions were determined at 7 other thick exposures of the Peach Springs Tuff. The steeper component is presumably a later-stage magnetization acquired after prolonged cooling of the ignimbrite. When compared to the Plateau reference direction, tilt-corrected directions from 3 of 6 sites in the central Mojave strike-slip zone show localized rotations up to 13° in the vicinity of strike-slip faults. The other three sites show no significant rotations with respect to the Colorado Plateau. Both clockwise and counterclockwise rotations were measured, and no systematic regional pattern is evident. Our results do not support kinematic models which require consistent rotation of large regions to accommodate the cumulative displacement of major post-middle Miocene strike-slip faults in the central Mojave Desert. Most of our sites in the Transition Zone and Basin and Range province have had no significant rotation, although small counterclockwise rotation in the McCullough and New York Mountains may be related to sinistral shear along en echelon faults southwest of the Lake Mead shear zone. The larger rotations occur in the Colorado River extensional corridor, where 8 of 14 sites show rotations ranging from 37° clockwise to 51° counterclockwise. These rotations occur in allochthonous tilt blocks which have been transported northeastward above the Chemehuevi-Whipple Mountains detachment fault. Upper-plate blocks within 1 km of the exposed detachment unexpectedly show no significant rotation. From this relation, we infer that rotations are accommodated along numerous low-angle faults at higher structural levels above the detachment surface.

Imaging the polarity switch between large seismogenic normal faults in the southern Apennines (Italy)

NASA Astrophysics Data System (ADS)

Fracassi, U.; Milano, G.; di Giovambattista, R.; Ventura, G.

2009-04-01

The backbone of Italy's Apennines hosts the majority of the seismic moment release in the Italian peninsula. In particular, the area among the southern Abruzzo, southeastern Lazio and Molise regions in central-southern Italy includes the polarity switch, from north to south, between the large SW-verging seismogenic normal faults (the southernmost one being the Aremogna-Cinque Miglia, responsible for a Mw 6.4 event dated 800 B.C-1030 A.D.) and those NE-verging ones (the northernmost one being the Boiano Basin, responsible for the 26 July 1805, Mw 6.6 Molise earthquake), including the Carpino-Le Piane fault system. In addition, the area between these two faults is the locus of extension parallel to the chain axis, as shown by a low-magnitude (M < 3.3) seismic sequence occurred in 2001. As GPS data illustrate, NE-SW striking extension predominates in the western and the inner sectors of the Apennines. All active normal faults along the crest of the Apennines are essentially parallel to the mountain range (NW-SE) and are governed by the current extensional regime that has been in place since the Middle-Upper Pleistocene. However, the occurrence of such polarity switch between antithetic, conjugate seismogenic normal faults in Italy is very uncommon. In addition, the area of research marks the abrupt end of the two (three?) sub-parallel seismogenic belts in Abruzzo (to the north) and the inception of the single, aligned one in Molise (to the south), including the western termination of E-W striking, large oblique-slip faulting in the foreland. In other words, this is a critical area concerning seismogenesis in central Italy and, therefore, the tectonic mechanism that either causes or influences such polarity switch could represent a key ingredient in the above scenario. Between January and May 2005, the RSN (Italy's National Seismometric Network) recorded a rise in the background seismicity, that has been recently relocated. This sequence is essentially a low magnitude (Md < 3), swarm activity that clustered within the Ortona-Roccamonfina line, a regional structure striking NNE-SSW and separating the central from the southern Apennines, hypothesized and discussed by numerous authors; in particular its field evidence is still debated, as much as its present-day activity. Our data show that, at least in the area where the 2005 sequence has occurred, the spatial trend of seismic activity essentially coincides with a sector of the Ortona-Roccamonfina line. Concerning fault polarity switches, there are numerous case studies in the literature where such examples have been recognized and associated with accommodation zones. Various authors have shown that either a hard (transfer fault) or soft linkage (relay ramp) is kinematically needed to accommodate strain between the two. This would be particularly true in the case we present, i.e. with two large (~20-25 km long) convergent, approaching faults, at a distance (20-25 km) comparable in size to the length of the faults in question. According to these literature models for transfer zones, such transfer would occur at ~45° to the strike of the concerned faults, that is ~N-S in the studied area. The location of the clustered seismicity that occurred in 2005 between the Abruzzo and Molise regions shows a ~NNE-SSW alignment and falls within the area where a major polarity switch between large seismogenic faults occur. On the basis of (i) the spatial-temporal characteristics of this data and (ii) the geometry and kinematics of active faulting in the region, we hypothesize (a) the existence of a transfer zone between the Aremogna-Cinque Miglia and Boiano Basin faults, and (b) the activity of such linkage along the Ortona-Roccamonfina line in this sector of the chain where a major transition, both structural and seismogenic, occurs. Alternatively, this polarity switch could result mainly from the rheologic and tectonic control exerted by the abrupt passage between the two diverse paleogeographic domains that make up the boundary between the central and southern Apennines. The role of such possible control onto the nature and geometry of the transfer zone and their interaction with one another, including seismic activity, is part of a larger study currently underway.

Kinematics of the New Madrid seismic zone, central United States, based on stepover models

USGS Publications Warehouse

Pratt, Thomas L.

2012-01-01

Seismicity in the New Madrid seismic zone (NMSZ) of the central United States is generally attributed to a stepover structure in which the Reelfoot thrust fault transfers slip between parallel strike-slip faults. However, some arms of the seismic zone do not fit this simple model. Comparison of the NMSZ with an analog sandbox model of a restraining stepover structure explains all of the arms of seismicity as only part of the extensive pattern of faults that characterizes stepover structures. Computer models show that the stepover structure may form because differences in the trends of lower crustal shearing and inherited upper crustal faults make a step between en echelon fault segments the easiest path for slip in the upper crust. The models predict that the modern seismicity occurs only on a subset of the faults in the New Madrid stepover structure, that only the southern part of the stepover structure ruptured in the A.D. 1811–1812 earthquakes, and that the stepover formed because the trends of older faults are not the same as the current direction of shearing.

A 667 year record of coseismic and interseismic Coulomb stress changes in central Italy reveals the role of fault interaction in controlling irregular earthquake recurrence intervals

NASA Astrophysics Data System (ADS)

Wedmore, L. N. J.; Faure Walker, J. P.; Roberts, G. P.; Sammonds, P. R.; McCaffrey, K. J. W.; Cowie, P. A.

2017-07-01

Current studies of fault interaction lack sufficiently long earthquake records and measurements of fault slip rates over multiple seismic cycles to fully investigate the effects of interseismic loading and coseismic stress changes on the surrounding fault network. We model elastic interactions between 97 faults from 30 earthquakes since 1349 A.D. in central Italy to investigate the relative importance of co-seismic stress changes versus interseismic stress accumulation for earthquake occurrence and fault interaction. This region has an exceptionally long, 667 year record of historical earthquakes and detailed constraints on the locations and slip rates of its active normal faults. Of 21 earthquakes since 1654, 20 events occurred on faults where combined coseismic and interseismic loading stresses were positive even though 20% of all faults are in "stress shadows" at any one time. Furthermore, the Coulomb stress on the faults that experience earthquakes is statistically different from a random sequence of earthquakes in the region. We show how coseismic Coulomb stress changes can alter earthquake interevent times by 103 years, and fault length controls the intensity of this effect. Static Coulomb stress changes cause greater interevent perturbations on shorter faults in areas characterized by lower strain (or slip) rates. The exceptional duration and number of earthquakes we model enable us to demonstrate the importance of combining long earthquake records with detailed knowledge of fault geometries, slip rates, and kinematics to understand the impact of stress changes in complex networks of active faults.

Post-Paleogene Deformation in central Anatolia, South of Ankara (Turkey)

NASA Astrophysics Data System (ADS)

Rojay, Bora

2014-05-01

The closure of the northern Neo-Tethys took place between Eurasia in the north and northern edge of Afro- Arabian plate in the south since the Early Cretaceous is documented in central Anatolia. It is mated by Cretaceous ophiolitic mélanges thrusted over southwards on to the upper Cretaceous-Paleogene fore-arc and foreland sequences along the northern margins of Haymana and Tuzgölü basins, respectively. Two main deformation episodes are recognized in the region. These include post-Cretaceous-pre Miocene compressional regime and Miocene to mid-Pliocene transcurrent regime dominated extensional deformation. The first regime is characterize by NW-SE directed compressional and contractional deformation dominated by south vergent, large wave length, asymmetric to overturned folds and associated thrust/reverse faults. Some of these reverse faults were reactivated as strike-slip faults with reverse components as evidenced by cross-cutting relationships and overprinting slickensides observed extensively in the field. Along these reactivated faults, echelon calcite veins, fault parallel meter thick silica walls with repeated phases of deformation are very common. Following the Miocene, the region is affected by a NNE-SSW to NE-SW directed extension, possibly resulted from the interaction of Tuzgölü Fault with the northwards convex splays of dextral North Anatolian Fault extending into the region. As a conclusion, the Paleogene sequences with ophiolitic mélanges are deformed under NNE-SSW directed compression related to the development of dextral strike slip tectonics during post-Paleogene-pre-Miocene period. Keywords:fault plane slip data, transcurrent regime, post-Paleogene, central Anatolia.

Palaeomagnetic study of the Kepezdaǧ and Yamadaǧ volcanic complexes, central Turkey: Neogene tectonic escape and block definition in the central-east Anatolides

NASA Astrophysics Data System (ADS)

Gürsoy, H.; Tatar, O.; Piper, J. D. A.; Koçbulut, F.; Akpınar, Zafer; Huang, Baochun; Roberts, A. P.; Mesci, B. L.

2011-05-01

The Anatolian accretionary collage between Afro-Arabia and Eurasia is currently subject to two tectonic regimes. Ongoing slip of Arabia relative to Africa along the Dead Sea Fault Zone in the east is extruding crustal blocks away from the indenter by a combination of strike-slip and rotation. This zone of compression gives way to an extensional province in western Turkey, which also includes the eastern sector of Aegean Province. Although it is now well established that rotational deformation throughout Anatolia is distributed and differential, the sizes of the blocks involved are poorly understood. As a contribution towards evaluating this issue in central-east Turkey, we report palaeomagnetic study of the mid-Miocene Kepezdağ and Yamadağ volcanic complexes in central-south Anatolia (38-39.5°N, 37.5-39°E). A distributed sample through the Yamadağ complex identifies eruption during an interval of multiple geomagnetic field reversals (40 normal, 36 reversed, 8 intermediate sites) with a selected mean defined by 63 sites of D/ I = 335.4/51.1° ( α95 = 4.4°). The smaller Kepezdağ complex (8 reversed, 4 normal and 1 intermediate site) yields a comparable mean direction from 12 sites of 338.7/49.8° ( α95 = 14.1°). In the context of a range of radiometric age evidence, two thick normal polarity zones within the Yamadağ succession probably correlate with zones C5ACn and C5ADn of the Geomagnetic Polarity Time Scale and imply that the bulk of the volcanic activity took place between ˜15 and 13.5 Ma. Comparison of the palaeomagnetic results with the adjoining major plate indenters shows that the Yamadağ complex has rotated CCW by 29.3 ± 5.2° relative to Eurasia; the much smaller dataset from the Kepezdağ complex indicates a comparable CCW rotation of 26.0 ± 11.8° with respect to Eurasia. The Arabian Indenter has also been rotating CCW since mid Miocene times, and the block incorporating these two volcanic complexes north of the East Anatolian Fault Zone (EAFZ) is determined to have rotated 18.2 ± 6.0° CCW relative to the northern perimeter of Arabia. Comparison with data to the north identifies quasi-uniform rotation across a ˜200 km wide block extending from the Central Anatolian Fault Zone in the northwest to close to the East Anatolian transform fault zone in the south east. Although absence of suitable younger rocks does not permit the timing of this rotation to be determined in the study area, analogies with results from the Sivas Basin suggest that it is young, and followed establishment of the major transform faults. Rotation has evidently taken place around bounding arcuate faults and accompanied westward expulsion as the accretionary collage north of Arabia has been subject to ongoing post-collisional indentation.

Combined Application of Shallow Seismic Reflection and High-resolution Refraction Exploration Approach to Active Fault Survey, Central Orogenic Belt, China

NASA Astrophysics Data System (ADS)

Lin, S.; Luo, D.; Yanlin, F.; Li, Y.

2016-12-01

Shallow Seismic Reflection (SSR) is a major geophysical exploration method with its exploration depth range, high-resolution in urban active fault exploration. In this paper, we carried out (SSR) and High-resolution refraction (HRR) test in the Liangyun Basin to explore a buried fault. We used NZ distributed 64 channel seismic instrument, 60HZ high sensitivity detector, Geode multi-channel portable acquisition system and hammer source. We selected single side hammer hit multiple overlay, 48 channels received and 12 times of coverage. As there are some coincidence measuring lines of SSR and HRR, we chose multi chase and encounter observation system. Based on the satellite positioning, we arranged 11 survey lines in our study area with total length for 8132 meters. GEOGIGA seismic reflection data processing software was used to deal with the SSR data. After repeated tests from the aspects of single shot record compilation, interference wave pressing, static correction, velocity parameter extraction, dynamic correction, eventually got the shallow seismic reflection profile images. Meanwhile, we used Canadian technology company good refraction and tomographic imaging software to deal with HRR seismic data, which is based on nonlinear first arrival wave travel time tomography. Combined with drilling geological profiles, we explained 11 measured seismic profiles. Results show 18 obvious fault feature breakpoints, including 4 normal faults of south-west, 7 reverse faults of south-west, one normal fault of north-east and 6 reverse faults of north-east. Breakpoints buried depth is 15-18 meters, and the inferred fault distance is 3-12 meters. Comprehensive analysis shows that the fault property is reverse fault with northeast incline section, and fewer branch normal faults presenting southwest incline section. Since good corresponding relationship between the seismic interpretation results, drilling data and SEM results on the property, occurrence, broken length of the fault, we considered the Liangyun fault to be an active fault which has strong activity during the Neogene Pliocene and early Pleistocene, Middle Pleistocene period. The combined application of SSR and HRR can provide more parameters to explain the seismic results, and improve the accuracy of the interpretation.

The 2011 Hawthorne, Nevada, Earthquake Sequence; Shallow Normal Faulting

NASA Astrophysics Data System (ADS)

Smith, K. D.; Johnson, C.; Davies, J. A.; Agbaje, T.; Knezevic Antonijevic, S.; Kent, G.

2011-12-01

An energetic sequence of shallow earthquakes that began in early March 2011 in western Nevada, near the community of Hawthorne, has slowly decreased in intensity through mid-2011. To date about 1300 reviewed earthquake locations have been compiled; we have computed moment tensors for the larger earthquakes and have developed a set of high-precision locations for all reviewed events. The sequence to date has included over 50 earthquakes ML 3 and larger with the largest at Mw 4.6. Three 6-channel portable stations configured with broadband sensors and accelerometers were installed by April 20. Data from the portable instruments is telemetered through NSL's microwave backbone to Reno where it is integrated with regional network data for real-time notifications, ShakeMaps, and routine event analysis. The data is provided in real-time to NEIC, CISN and the IRIS DMC. The sequence is located in a remote area about 15-20 km southwest of Hawthorne in the footwall block of the Wassuk Range fault system. An initial concern was that the sequence might be associated with volcanic processes due to the proximity of late Quaternary volcanic flows; there have been no volcanic signatures observed in near source seismograms. An additional concern, as the sequence has proceeded, was a clear progression eastward toward the Wassuk Range front fault. The east dipping range bounding fault is capable of M 7+ events, and poses a significant hazard to the community of Hawthorne and local military facilities. The Hawthorne Army Depot is an ordinance storage facility and the nation's storage site for surplus mercury. The sequence is within what has been termed the 'Mina Deflection' of the Central Walker Lane Belt. Faulting along the Whiskey Flat section of the Wassuk front fault would be primarily down-to-the-east, with an E-W extension direction; moment tensors for the 2011 earthquake show a range of extension directions from E-W to NW-SE, suggesting a possible dextral component to the Wassuk Range front fault at this latitude. At least two faults have been imaged within the sequence; these structures are at shallow depth (3-6 km), strike NE, and dip ~NW. Prior to temporary station installation event depths were poorly constrained, with the nearest network station 25 km from the source area. Early sequence moment tensor solutions show depths are on the order of 2-6 km and locations using the near source stations also confirm the shallow depths of the Hawthorne sequence. S-P times of 0.5 sec and less have been observed on a near-source station, illustrating extremely shallow source depths for some events. Along with the 2011 Hawthorne activity, very shallow depths in Nevada have been observed from near source stations in the 2008 west Reno earthquake sequence (primarily strike-slip faulting; main shock Mw 5.0) and the 1993 Rock Valley sequence in southern NNSS (strike-slip faulting; main shock Mw 4.0). These shallow sequences tend to include high rates of low magnitude earthquakes continuing over several months duration.

Long-term fault creep observations in central California

NASA Astrophysics Data System (ADS)

Schulz, Sandra S.; Mavko, Gerald M.; Burford, Robert O.; Stuart, William D.

1982-08-01

The U.S. Geological Survey (USGS) has been monitoring aseismic fault slip in central California for more than 10 years as part of an earthquake prediction experiment. Since 1968, the USGS creep network has grown from one creep meter at the Cienega Winery south of Hollister to a 44-station network that stretches from Hayward, east of San Francisco Bay, to Palmdale in southern California. In general, the long-term slip pattern is most variable on sections of the faults where several magnitude 4 and larger earthquakes occurred during the recording period (e.g., Calaveras fault near Hollister and San Andreas fault between San Juan Bautista and Bear Valley). These fault sections are the most difficult to characterize with a single long-term slip rate. In contrast, sections of the faults that are seismically relatively quiet (e.g., San Andreas fault between Bear Valley and Parkfield) produce the steadiest creep records and are easiest to fit with a single long-term slip rate. Appendix is available with entire article on microfiche. Order from the American Geophysical Union, 2000 Florida Avenue, N.W., Washington, D.C. 20009. Document J82-004; $1.00. Payment must accompany order.

Deciphering Past and Present Tectonics of the Rio Grande Rift in New Mexico Utilizing Apatite Fission Track Thermochronology, Geochronology, Quaternary Faulting, and Cross-Section Restoration

NASA Astrophysics Data System (ADS)

Ricketts, J. W.; Karlstrom, K. E.; Kelley, S. A.; Priewisch, A.; Crossey, L. J.; Asmerom, Y.; Polyak, V.; Selmi, M.

2011-12-01

The Rio Grande rift provides an excellent laboratory for understanding styles and processes of extensional tectonics, and their driving forces. We apply apatite fission track (AFT) thermochronology, geochronology, fracture analysis, and cross-section restoration to decipher past and present tectonics of the Rio Grande rift. AFT data has been compiled from rift flank uplifts along the Rio Grande rift in an attempt to recognize long wavelength spatial and temporal patterns. AFT ages record time of cooling of rocks below ~110°C and, when cooling is due to exhumation, age elevation traverses can record upward advection of rocks through paleo 110°C isotherms. The relatively passive sides of half-grabens (e.g. Manzanos and Santa Fe Range) preserve Laramide AFT ages ranging from 45-70 Ma, indicating they were cooled during the Laramide Orogeny and have remained cooler than 110°C since then. Rift flanks on the tectonically active sides of half-grabens, (e.g. Sierra Ladrones, Sandias, Taos Range, and Sierra Blanca) have AFT ages that range from 35 Ma to <10 Ma, and record cooling that initiated with the Oligocene ignimbrite flare-up and continues through the Neogene. Our analysis tracks the approximate elevation of paleo 110°C isotherms in 10 Ma intervals from the Laramide to the present and shows that reconstructed paleoisotherms have been differentially uplifted, warped, and faulted since their time of formation, and hence serve as markers of uplift history and its mechanisms. AFT data at Ladron Peak, an active rift flank along the western margin of the Rio Grande rift in central New Mexico, indicates that it was rapidly unroofed between 20-10 Ma. Preliminary apatite helium data gives a similar age vs. elevation trend, but apatites have highly radiogenically damaged lattices and hence have corrected closure temperatures tens of degrees higher than AFT ages. The style of faulting at Ladron Peak is unusual because it is bounded by the anomalously low-angle (~15°) Jeter fault. In order to understand the evolution of faulting in this region, a balanced cross-section was constructed and restored to its pre-rift geometry. Our working hypothesis is that the low angle of the Jeter fault is most adequately explained by a rolling hinge model, where isostatic uplift causes progressive rotation of an initially steep (~60°) normal fault to shallower dips. Thirty km north of Ladron along the west side of the rift, Quaternary extensional faulting is evident in large travertine deposits at the Belen Quarry. Extensional fractures and cm-scale displacement normal faults at 4 locations give average paleostress orientations of 087, 112, 116, 127. A U-series age of 312 ka on faulted upper layers in one quarry indicates post-312 ka slip that we interpret to reflect surface manifestations of microseismicity above the Socorro magma body.

A 'Propagating' Active Across-Arc Normal Fault Shows Rupture Process of the Basement: the Case of the Southwestern Ryukyu Arc

NASA Astrophysics Data System (ADS)

Matsumoto, T.; Shinjo, R.; Nakamura, M.; Kubo, A.; Doi, A.; Tamanaha, S.

2011-12-01

Ryukyu Arc is located on the southwestern extension of Japanese Island-arc towards the east of Taiwan Island along the margin of the Asian continent off China. The island-arc forms an arcuate trench-arc-backarc system. A NW-ward subduction of the Philippine Sea Plate (PSP)at a rate of 6-8 cm/y relative to the Eurasian Plate (EP) causes frequent earthquakes. The PSP is subducting almost normally in the north-central area and more obliquely around the southwestern area. Behind the arc-trench system, the Okinawa Trough (OT) was formed by back-arc rifting, where active hydrothermal vent systems have been discovered. Several across-arc submarine faults are located in the central and southern Ryukyu Arc. The East Ishigaki Fault (EIF) is one of the across-arc normal faults located in the southwestern Ryukyu Arc, ranging by 44km and extending from SE to NW. This fault was surveyed by SEABAT8160 multibeam echo sounder and by ROV Hyper-Dolphin in 2005 and 2008. The result shows that the main fault consists of five fault segments. A branched segment from the main fault was also observed. The southernmost segment is most mature (oldest but still active) and the northernmost one is most nascent. This suggests the north-westward propagation of the fault rupture corresponding to the rifting of the southwestern OT and the southward retreat of the arc-trench system. Considering that the fault is segmented and in some part branched, propagation might take place episodically rather than continuously from SE to NW. The ROV survey also revealed the rupture process of the limestone basement along this fault from the nascent stage to the mature stage. Most of the rock samples collected from the basement outcrop were limestone blocks (or calcareous sedimentary rocks). Limestone basement was observed to the west on the hanging wall far away from the main fault scarp. Then fine-grained sand with ripple marks was observed towards the main scarp. Limestone basement was observed on the main scarp and on the footwall. These suggest that basically the both sides are composed of the same material, that the whole study area is characterised by Ryukyu limestone exposure and that the basement was split by the across-arc normal fault. Coarse-grained sand and gravels/rubbles were observed towards and on the trough of the fault. On the main scarp an outcrop of limestone basement was exposed and in some part it was broken into rubbles. These facts suggest that crash of the basement due to rupturing is taking place repeatedly on the scarp and the trough. The observed fine-grained sand on the hanging wall might be the final product by the process of the crash of the limestone basement.

Surface faulting and paleoseismic history of the 1932 Cedar Mountain earthquake area, west-central Nevada, and implications for modern tectonics of the Walker Lane

USGS Publications Warehouse

Bell, J.W.; DePolo, C.M.; Ramelli, A.R.; Sarna-Wojcicki, A. M.; Meyer, C.E.

1999-01-01

The 1932 Cedar Mountain earthquake (Ms 7.2) was one of the largest historical events in the Walker Lane region of western Nevada, and it produced a complicated strike-slip rupture pattern on multiple Quaternary faults distributed through three valleys. Primary, right-lateral surface ruptures occurred on north-striking faults in Monte Cristo Valley; small-scale lateral and normal offsets occurred in Stewart Valley; and secondary, normal faulting occurred on north-northeast-striking faults in the Gabbs Valley epicentral region. A reexamination of the surface ruptures provides new displacement and fault-zone data: maximum cumulative offset is estimated to be 2.7 m, and newly recognized faults extend the maximum width and end-to-end length of the rupture zone to 17 and 75 km, respectively. A detailed Quaternary allostratigraphic chronology based on regional alluvialgeomorphic relationships, tephrochronology, and radiocarbon dating provides a framework for interpreting the paleoseismic history of the fault zone. A late Wisconsinan alluvial-fan and piedmont unit containing a 32-36 ka tephra layer is a key stratigraphic datum for paleoseismic measurements. Exploratory trenching and radiocarbon dating of tectonic stratigraphy provide the first estimates for timing of late Quaternary faulting along the Cedar Mountain fault zone. Three trenches display evidence for six faulting events, including that in 1932, during the past 32-36 ka. Radiocarbon dating of organic soils interstratified with tectonically ponded silts establishes best-fit ages of the pre-1932 events at 4, 5,12,15, and 18 ka, each with ??2 ka uncertainties. On the basis of an estimated cumulative net slip of 6-12 m for the six faulting events, minimum and maximum late Quaternary slip rates are 0.2 and 0.7 mm/yr, respectively, and the preferred rate is 0.4-0.5 mm/yr. The average recurrence (interseismic) interval is 3600 yr. The relatively uniform thickness of the ponded deposits suggests that similar-size, characteristic rupture events may characterize late Quaternary slip on the zone. A comparison of event timing with the average late Quaternary recurrence interval indicates that slip has been largely regular (periodic) rather than temporally clustered. To account for the spatial separation of the primary surface faulting in Monte Cristo Valley from the epicenter and for a factor-of-two-to-three disparity between the instrumentally and geologically determined seismic moments associated with the earthquake, we hypothesize two alternative tectonic models containing undetected subevents. Either model would adequately account for the observed faulting on the basis of wrench-fault kinematics that may be associated with the Walker Lane. The 1932 Cedar Mountain earthquake is considered an important modern analogue for seismotectonic modeling and estimating seismic hazard in the Walker Lane region. In contrast to most other historical events in the Basin and Range province, the 1932 event did not occur along a major range-bounding fault, and no single, throughgoing basement structure can account for the observed rupture pattern. The 1932 faulting supports the concept that major earthquakes in the Basin and Range province can exhibit complicated distributive rupture patterns and that slip rate may not be a reliable criterion for modeling seismic hazard.

The Qartaba Structure: An Active Backthrust In Central Mt-Lebanon.

NASA Astrophysics Data System (ADS)

Elias, Ata Richard

2016-04-01

The Qartaba structure in central Mt-Lebanon is a 15x5km box fold running parallel to the restraining bend of the sinsitral Yammouneh Fault, the main fault of the central segment of the Dead Sea Transform. The Qartaba structure has long been described as a "horst" and associated with Mesozoic normal faulting. However, the Qartaba anticline is suitably oriented with the direction of maximum compression along the restraining bend. Jurassic carbonate rocks form the core of this anticline culminating at ~1953m asl to the east, of the highest structural elevation of the Mt-Lebanon range indicating important tectonic uplift rate. The fold is asymmetric. The western limb is steep and bordered by the Lebanese Flexure, a prominent continuous monocline of Upper Jurassic to Mid Cretaceous rocks, running along the western flank of Mt-Lebanon. The eastern limb of the anticline has a very steep dip, and forms a 200m high cliff well marked in the topography. Its Jurassic layers are almost vertical and end up overhanging Lower Cretaceous beds. Our study suggest that the Qartaba structure is a growing anticline, built by active thrusting over a west dipping thrust fault that cuts the surface at the base of the eastern limb of the anticline. The fault plane can be seen dipping 30-35 degrees to the west. At depth, this thrust is likely to connect with the blind thrust ramp of the Mt-Lebanon Flexure. The Qartaba backthrust with a dip to the west, is opposite to the general vergence of similar structures in the area. On some of the segments of the steep cliff forming the faulted eastern limb, a fresh scarp with smooth and polished surfaces bearing vertical slickensides can be followed over ~700m along the base of the cliff. It corresponds with the location of the thrust fault tip. Talus accumulation over the steep eastern limb covers most of the cliff base, and may be masking further extent of this scarp. We interpret this scarp as the freeface of a co-seismic rupture on the underlying Qartaba backthrust. Moreover a first paleoseismic trench was opened in the loose deposits that cover the base of the eastern limb, over a topographic slope break aligned with the direction of the backthrust. The preliminary results clearly show tectonic deformation structures in C14 dated Holocene sediments, compatible with the general compressive style of the backthrust. This new interpretation of the Qartaba structure has important, implications on the geological interpretation of the area. The Qartaba backthrust is clearly an active structure that is capable of generating Mw~6.4 earthquakes in central Lebanon, significantly adding to the seismic hazard of the area. Moreover, the different interpretations of the geology of this area for petroleum prospects studies should be reviewed in the light of these new results.

Caldera collapse: Perspectives from comparing Galápagos volcanoes, nuclear-test sinks, sandbox models, and volcanoes on Mars

USGS Publications Warehouse

Howard, K.A.

2010-01-01

The 1968 trapdoor collapse (1.5 km3) of Fernandina caldera in the Galapágos Islands developed the same kinds of structures as found in small sandbox-collapse models and in concentrically zoned sinks formed in desert alluvium by fault subsidence into underground nuclear-explosion cavities. Fernandina’s collapse developed through shear failure in which the roof above the evacuating chamber was lowered mostly intact. This coherent subsidence contrasts to chaotic piecemeal collapse at small, rocky pit craters, underscoring the role of rock strength relative to subsidence size. The zoning at Fernandina implies that the deflated magma chamber underlay a central basin and a bordering inward-dipping monocline, which separates a blind inner reverse fault from an outer zone of normal faulting. Similar concentric zoning patterns can be recognized in coherent subsidence structures ranging over 16 orders of magnitude in size, from sandbox experiments to the giant Olympus Mons caldera on Mars.

Subsurface geometry of the San Andreas fault in southern California: Results from the Salton Seismic Imaging Project (SSIP) and strong ground motion expectations

USGS Publications Warehouse

Fuis, Gary S.; Bauer, Klaus; Goldman, Mark R.; Ryberg, Trond; Langenheim, Victoria; Scheirer, Daniel S.; Rymer, Michael J.; Stock, Joann M.; Hole, John A.; Catchings, Rufus D.; Graves, Robert; Aagaard, Brad T.

2017-01-01

The San Andreas fault (SAF) is one of the most studied strike‐slip faults in the world; yet its subsurface geometry is still uncertain in most locations. The Salton Seismic Imaging Project (SSIP) was undertaken to image the structure surrounding the SAF and also its subsurface geometry. We present SSIP studies at two locations in the Coachella Valley of the northern Salton trough. On our line 4, a fault‐crossing profile just north of the Salton Sea, sedimentary basin depth reaches 4 km southwest of the SAF. On our line 6, a fault‐crossing profile at the north end of the Coachella Valley, sedimentary basin depth is ∼2–3  km">∼2–3  km and centered on the central, most active trace of the SAF. Subsurface geometry of the SAF and nearby faults along these two lines is determined using a new method of seismic‐reflection imaging, combined with potential‐field studies and earthquakes. Below a 6–9 km depth range, the SAF dips ∼50°–60°">∼50°–60° NE, and above this depth range it dips more steeply. Nearby faults are also imaged in the upper 10 km, many of which dip steeply and project to mapped surface fault traces. These secondary faults may join the SAF at depths below about 10 km to form a flower‐like structure. In Appendix D, we show that rupture on a northeast‐dipping SAF, using a single plane that approximates the two dips seen in our study, produces shaking that differs from shaking calculated for the Great California ShakeOut, for which the southern SAF was modeled as vertical in most places: shorter‐period (T<1  s">T<1  s) shaking is increased locally by up to a factor of 2 on the hanging wall and is decreased locally by up to a factor of 2 on the footwall, compared to shaking calculated for a vertical fault.

Exhumation history of the deepest central Himalayan rocks, Ama Drime range: Key pressure-temperature-deformation-time constraints on orogenic models

NASA Astrophysics Data System (ADS)

Kali, E.; Leloup, P. H.; Arnaud, N.; MahéO, G.; Liu, Dunyi; Boutonnet, E.; van der Woerd, J.; Liu, Xiaohan; Liu-Zeng, Jing; Li, Haibing

2010-04-01

The Ama Drime range located at the transition between the high Himalayan range and south Tibet is a N-S active horst that offsets the South Tibetan Detachment System (STDS). Within the horst, a paragneissic unit, possibly attributed to the upper Himalayan crystalline series, overly the lower Himalayan crystalline series Ama Drime orthogneissic unit containing large metabasite layers and pods that have experienced pressure ≥1.4 GPa. Combining structural analysis with new and published pressure-temperature (P-T) estimates as well as U-Th/Pb, 39Ar/40Ar and (U-Th)/He ages, the P-T-deformation-time (P-T-D-t) paths of the main units within and on both sides of the horst are reconstructed. They imply that N-S normal faults initiated prior to 11 Ma and have accounted for a total exhumation ≤0.6 GPa (22 km) that probably occurred in two phases: the first one until ˜9 Ma and the second one since 6 to 4 Ma at a rate of ˜1 mm/yr. In the Ama Drime unit, 1 to 1.3 GPa (37 to 48 km) of exhumation occurred after partial melting since ˜30 Ma until ˜13 Ma, above the Main Central Trust (MCT) and below the STDS when these two fault systems were active together. The switch from E-W (STDS) to N-S (Ama Drime horst) normal faulting between 13 and 12 Ma occurs at the time of propagation of thrusting from the MCT to the Main Boundary Thrust. These data are in favor of a wedge extrusion or thrust system rather than a crustal flow model for the building of the Himalaya. We propose that the kinematics of south Tibet Cenozoic extension phases is fundamentally driven by the direction and rate of India underthrusting.

Structure and Tectonics of the Saint Elias Orogen

NASA Astrophysics Data System (ADS)

Bruhn, R. L.; Pavlis, T. L.; Plafker, G.; Serpa, L.; Picornell, C.

2001-12-01

The Saint Elias orogen of western Canada and southern Alaska is a complex mountain belt formed by transform faulting and subduction between the Pacific and North American plates, and collision of the Yakutat terrane. The orogen is segmented into three regions of different structural style caused by lateral variations in transpression and processes of terrane accretion. Deformation is strain and displacement partitioned throughout the orogen; transcurrent motion is focused along discrete strike-slip faults, and shortening is distributed among reverse faults and folds with sub-horizontal axes. Plunging folds accommodate horizontal shortening and extension in the western part of the orogen. Segment boundaries extend across the Yakutat terrane where they coincide with the courses of huge piedmont glaciers that flow from the topographic backbone of the range onto the coastal plain. The eastern segment is marked by strike-slip faulting along the Fairweather transform fault and by a narrow belt of reverse faulting where the transpression ratio is 0.4:1 shortening to dextral shear. The transpression ratio is 1.7:1 in the central part of the orogen where a broad thin-skinned fold and thrust belt deforms the Yakutat terrane south of the Chugach-Saint Elias (CSE) suture. Dextral shearing is accommodated by strike-slip faulting beneath the Seward and Bagley glaciers in the hanging wall of the CSE suture, and partly by reverse faulting along a structural belt that cuts across the Yakutat terrane along the western edge of the Malaspina Glacier and links to the Pamplona fold and thrust belt offshore. Deformation along this segment boundary is probably also driven by vertical axis bending of the Yakutat microplate during collision. Subduction & accretion in the western segment of the orogen causes re-folding of previously formed structures when they are emplaced into the upper plate of the Alaska-Aleutian mega-thrust. Second phase folds plunge at moderate to steep angles and accretion is marked by only modest amounts of uplift. The structural boundary between the central and western segments of the orogen localizes the course of the Bering piedmont glacier. The structural segments coincide with subdivisions in historical seismicity, particularly ruptures of great to large magnitude earthquakes. The results of this structural study provide the requisite geological framework to design new-generation geophysical monitoring systems to study active deformation within the orogen.

Magma-Tectonic Interactions along the Central America Volcanic Arc: Insights from the August 1999 Magmatic and Tectonic Event at Cerro Negro, Nicaragua

NASA Astrophysics Data System (ADS)

La Femina, P.; Connor, C.; Strauch, W.

2002-12-01

Volcanic vent alignments form parallel to the direction of maximum horizontal stress, accommodating extensional strain via dike injection. Roughly east-west extension within the Central America Volcanic Arc is accommodated along north-northwest-trending basaltic vent alignments. In Nicaragua, these alignments are located in a northwest-trending zone of dextral shear, with shear accommodated along northeast trending bookshelf faults. The recent eruption of Cerro Negro volcano, Nicaragua and Marabios Range seismic swarm revealed the interaction of these fault systems. A low energy (VEI 1), small volume (0.001 km3 DRE) eruption of highly crystalline basalt occurred at Cerro Negro volcano, Nicaragua, August 5-7, 1999. This eruption followed three tectonic earthquakes (each Mw 5.2) in the vicinity of Cerro Negro hours before the onset of eruptive activity. The temporal and spatial pattern of microseismicity and focal mechanisms of the Mw 5.2 earthquakes suggests the activation of northeast-trending faults northwest and southeast of Cerro Negro within the Marabios Range. The eruption was confined to three new vents formed on the southern flank of Cerro Negro along a preexisting north-northwest trending alignment; the El Hoyo alignment of cinder cones, maars and explosion craters. Surface ruptures formed > 1 km south and southeast of the new vents suggest dike injection. Numerical simulations of conduit flow illustrate that the observed effusion rates (up to 65 ms-1) and fountain heights (50-300 m) can be achieved by eruption of magma with little or no excess fluid pressure, in response to tectonic strain. These observations and models suggest that 1999 Cerro Negro activity is an excellent example of tectonically induced small-volume eruptions in an arc setting.

Slip distribution, strain accumulation and aseismic slip on the Chaman Fault system

NASA Astrophysics Data System (ADS)

Amelug, F.

2015-12-01

The Chaman fault system is a transcurrent fault system developed due to the oblique convergence of the India and Eurasia plates in the western boundary of the India plate. To evaluate the contemporary rates of strain accumulation along and across the Chaman Fault system, we use 2003-2011 Envisat SAR imagery and InSAR time-series methods to obtain a ground velocity field in radar line-of-sight (LOS) direction. We correct the InSAR data for different sources of systematic biases including the phase unwrapping errors, local oscillator drift, topographic residuals and stratified tropospheric delay and evaluate the uncertainty due to the residual delay using time-series of MODIS observations of precipitable water vapor. The InSAR velocity field and modeling demonstrates the distribution of deformation across the Chaman fault system. In the central Chaman fault system, the InSAR velocity shows clear strain localization on the Chaman and Ghazaband faults and modeling suggests a total slip rate of ~24 mm/yr distributed on the two faults with rates of 8 and 16 mm/yr, respectively corresponding to the 80% of the total ~3 cm/yr plate motion between India and Eurasia at these latitudes and consistent with the kinematic models which have predicted a slip rate of ~17-24 mm/yr for the Chaman Fault. In the northern Chaman fault system (north of 30.5N), ~6 mm/yr of the relative plate motion is accommodated across Chaman fault. North of 30.5 N where the topographic expression of the Ghazaband fault vanishes, its slip does not transfer to the Chaman fault but rather distributes among different faults in the Kirthar range and Sulaiman lobe. Observed surface creep on the southern Chaman fault between Nushki and north of City of Chaman, indicates that the fault is partially locked, consistent with the recorded M<7 earthquakes in last century on this segment. The Chaman fault between north of the City of Chaman to North of Kabul, does not show an increase in the rate of strain accumulation. However, lack of seismicity on this segment, presents a significant hazard on Kabul. The high rate of strain accumulation on the Ghazaband fault and lack of evidence for the rupture of the fault during the 1935 Quetta earthquake, present a growing earthquake hazard to the Balochistan and the populated areas such as the city of Quetta.

A Log-Scaling Fault Tolerant Agreement Algorithm for a Fault Tolerant MPI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hursey, Joshua J; Naughton, III, Thomas J; Vallee, Geoffroy R

The lack of fault tolerance is becoming a limiting factor for application scalability in HPC systems. The MPI does not provide standardized fault tolerance interfaces and semantics. The MPI Forum's Fault Tolerance Working Group is proposing a collective fault tolerant agreement algorithm for the next MPI standard. Such algorithms play a central role in many fault tolerant applications. This paper combines a log-scaling two-phase commit agreement algorithm with a reduction operation to provide the necessary functionality for the new collective without any additional messages. Error handling mechanisms are described that preserve the fault tolerance properties while maintaining overall scalability.

Post-caldera faulting of the Late Quaternary Menengai caldera, Central Kenya Rift (0.20°S, 36.07°E)

NASA Astrophysics Data System (ADS)

Riedl, Simon; Melnick, Daniel; Mibei, Geoffrey K.; Njue, Lucy; Strecker, Manfred R.

2015-04-01

A structural geological analysis of young caldera volcanoes is necessary to characterize their volcanic activity, assess their geothermal potential, and decipher the spatio-temporal relationships of faults on a larger tectonic scale. Menengai caldera is one of several major Quaternary trachytic caldera volcanoes that are aligned along the volcano-tectonic axis of the Kenya Rift, the archetypal active magmatic rift and nascent plate boundary between the Nubia and Somalia plates. The caldera covers an area of approximately 80 km² and is among the youngest and also largest calderas in the East African Rift, situated close to Nakuru - a densely populated urban area. There is an increasing interest in caldera volcanoes in the Kenya Rift, because these are sites of relatively young volcanic and tectonic activity, and they are considered important sites for geothermal exploration and future use for the generation of geothermal power. Previous studies of Menengai showed that the caldera collapsed in a multi-event, multiple-block style, possibly as early as 29 ka. In an attempt to characterize the youngest tectonic activity along the volcano-tectonic axis in the transition between the Central and Northern Kenya rifts we first used a high-resolution digital surface model, which we derived by structure-from-motion from an unmanned aerial vehicle campaign. This enabled us to identify previously unrecognized normal faults, associated dyke intrusions and volcanic eruptive centers, and transfer faults with strike-slip kinematics in the caldera interior and its vicinity. In a second step we verified these structures at outcrop scale, assessed their relationship with known stratigraphic horizons and dated units, and performed detailed fault measurements, which we subsequently used for fault-kinematic analysis. The most important structures that we mapped are a series of north-northeast striking normal faults, which cross-cut both the caldera walls and early Holocene lake shorelines outside the caldera. These faults have similar strikes as Pleistocene faults that define the left-stepping, north-northeast oriented segments of the volcano-tectonic axis of the inner trough of the Central Kenya Rift. In the center of the caldera, these faults are kinematically linked with oblique-slip and strike-slip transfer faults, similar to other sectors in the Central Kenya Rift. The structural setup of Menengai and the faults to the north and south of the eruptive center is thus compatible with tectono-magmatic activity in an oblique extensional tectonic regime, which reflects the tectonic and seismic activity along a nascent plate boundary.

Physical and Transport Properties of the carbonate-bearing faults: experimental insights from the Monte Maggio Fault zone (Central Italy)

NASA Astrophysics Data System (ADS)

Trippetta, Fabio; Scuderi, Marco Maria; Collettini, Cristiano

2015-04-01

Physical properties of fault zones vary with time and space and in particular, fluid flow and permeability variations are strictly related to fault zone processes. Here we investigate the physical properties of carbonate samples collected along the Monte Maggio normal Fault (MMF), a regional structure (length ~10 km and displacement ~500 m) located within the active system of the Apennines. In particular we have studied an exceptionally exposed outcrop of the fault within the Calcare Massiccio formation (massive limestone) that has been recently exposed by new roadworks. Large cores (100 mm in diameter and up to 20 cm long) drilled perpendicular to the fault plane have been used to: 1) characterize the damage zone adjacent to the fault plane and 2) to obtain smaller cores, 38 mm in diameter both parallel and perpendicular to the fault plane, for rock deformation experiments. At the mesoscale two types of cataclastic damage zones can be identified in the footwall block (i) a Cemented Cataclasite (CC) and (ii), a Fault Breccia (FB). Since in some portions of the fault the hangingwall (HW) is still preserved we also collected HW samples. After preliminary porosity measurements at ambient pressure, we performed laboratory measurements of Vp, Vs, and permeability at effective confining pressures up to 100 MPa in order to simulate crustal conditions. The protolith has a primary porosity of about 7 %, formed predominantly by isolated pores since the connected porosity is only 1%. FB samples are characterized by 10% and 5% of bulk and connected porosity respectively, whilst CC samples show lower bulk porosity (7%) and a connected porosity of 2%. From ambient pressure to 100 MPa, P-wave velocity is about 5,9-6,0 km/s for the protolith, ranges from 4,9 km/s to 5,9 km/s for FB samples, whereas it is constant at 5,9 km/s for CC samples and ranges from 5,4 to 5,7 for HW sample. Vs shows the same behaviour resulting in a constant Vp/Vs ratio from 0 to 100 MPa that ranges from 1,5 to 1,98 where the lower values are recorded for FB samples. Permeability of FB samples is pressure dependent starting from 10-17 m2 at ambient pressure to 10-18 m2 at 100 MPa confining pressure. In contrast, for CC samples, permeability is about 10-19 m2 and is pressure independent. In conclusion, our dataset depicts a fault zone structure with heterogeneous static physical and transport properties that are controlled by the occurrence of different deformation mechanisms related to different protolites. At the moment we have been conducting experiments during loading/unloading stress cycles in order to characterize possible permeability and acoustic properties evolution induced by differential stress.

Kinematics of a large-scale intraplate extending lithosphere: The Basin-Range

NASA Technical Reports Server (NTRS)

Smith, R. B.; Eddington, P. K.

1985-01-01

Upper lithospheric structure of the Cordilleran Basin Range (B-R) is characterised by an E-W symmetry of velocity layering. The crust is 25 km thick on its eastern active margin, thickening to 30 km within the central portion and thinning to approx. 25 km on the west. Pn velocities of 7.8 to 7.9 km/s characterize the upper mantle low velocity cushion, 7.4 km/s to 7.5 km/s, occurs at a depth of approx. 25 km in the eastern B-R and underlies the area of active extension. An upper-crustal low-velocity zone in the eastern B-R shows a marked P-wave velocity inversion of 7% at depths of 7 to 10 km also in the area of greatest extension. The seismic velocity models for this region of intraplate extension suggest major differences from that of a normal, thermally underformed continental lithosphere. Interpretations of seismic reflection data demonstrate the presence of extensive low-angle reflections in the upper-crust of the eastern B-R at depths from near-surface to 7 to 10 km. These reflections have been interpreted to represent low-angle normal fault detachments or reactivated thrusts. Seismic profiles across steeply-dipping normal faults in unconsolidated sediments show reflections from both planar to downward flatening (listric) faults that in most cases do not penetrate the low-angle detachments. These faults are interpreted as late Cenozoic and cataclastic mylonitic zones of shear displacement.

Long Valley caldera and the UCERF depiction of Sierra Nevada range-front faults

USGS Publications Warehouse

Hill, David P.; Montgomery-Brown, Emily K.

2015-01-01

Long Valley caldera lies within a left-stepping offset in the north-northwest-striking Sierra Nevada range-front normal faults with the Hilton Creek fault to the south and Hartley Springs fault to the north. Both Uniform California Earthquake Rupture Forecast (UCERF) 2 and its update, UCERF3, depict slip on these major range-front normal faults as extending well into the caldera, with significant normal slip on overlapping, subparallel segments separated by ∼10  km. This depiction is countered by (1) geologic evidence that normal faulting within the caldera consists of a series of graben structures associated with postcaldera magmatism (intrusion and tumescence) and not systematic down-to-the-east displacements consistent with distributed range-front faulting and (2) the lack of kinematic evidence for an evolving, postcaldera relay ramp structure between overlapping strands of the two range-front normal faults. The modifications to the UCERF depiction described here reduce the predicted shaking intensity within the caldera, and they are in accord with the tectonic influence that underlapped offset range-front faults have on seismicity patterns within the caldera associated with ongoing volcanic unrest.

Effects of the 2016 Kumamoto earthquakes on the Aso volcanic edifice

NASA Astrophysics Data System (ADS)

Tajima, Yasuhisa; Hasenaka, Toshiaki; Torii, Masayuki

2017-05-01

Large earthquakes occurred in the central part of Kumamoto Prefecture on April 14-16, 2016, causing severe damage to the northern segment of the Hinagu faults and the eastern segment of the Futagawa faults. Earthquake surface ruptures appeared along these faults and on the Aso volcanic edifice, which in turn generated landslides. We conducted landform change analysis of the central cones of Aso volcano by using satellite and aerial photographs. First, we categorized the topographical changes as surface scarps, arc-shaped cracks, and linear cracks. Field survey indicated that landslides caused the scarps and arc-shaped cracks, whereas faulting caused the linear cracks. We discovered a surface rupture concentration zone (RCZ) formed three ruptures bands with many surface ruptures and landslides extending from the west foot to the center of the Aso volcanic edifice. The magmatic volcanic vents that formed during the past 10,000 years are located along the north margin of the RCZ. Moreover, the distribution and dip of the core of rupture concentration zone correspond with the Nakadake craters. We conclude that a strong relationship exists between the volcanic vents and fault structures in the central cones of Aso volcano.[Figure not available: see fulltext.

Fault creep rates of the Chaman fault (Afghanistan and Pakistan) inferred from InSAR

NASA Astrophysics Data System (ADS)

Barnhart, William D.

2017-01-01

The Chaman fault is the major strike-slip structural boundary between the India and Eurasia plates. Despite sinistral slip rates similar to the North America-Pacific plate boundary, no major (>M7) earthquakes have been documented along the Chaman fault, indicating that the fault either creeps aseismically or is at a late stage in its seismic cycle. Recent work with remotely sensed interferometric synthetic aperture radar (InSAR) time series documented a heterogeneous distribution of fault creep and interseismic coupling along the entire length of the Chaman fault, including an 125 km long creeping segment and an 95 km long locked segment within the region documented in this study. Here I present additional InSAR time series results from the Envisat and ALOS radar missions spanning the southern and central Chaman fault in an effort to constrain the locking depth, dip, and slip direction of the Chaman fault. I find that the fault deviates little from a vertical geometry and accommodates little to no fault-normal displacements. Peak-documented creep rates on the fault are 9-12 mm/yr, accounting for 25-33% of the total motion between India and Eurasia, and locking depths in creeping segments are commonly shallower than 500 m. The magnitude of the 1892 Chaman earthquake is well predicted by the total area of the 95 km long coupled segment. To a first order, the heterogeneous distribution of aseismic creep combined with consistently shallow locking depths suggests that the southern and central Chaman fault may only produce small to moderate earthquakes (

Thermochronometry Across the Austroalpine-Pennine Boundary, Central Alps, Switzerland: Orogen-Perpendicular Normal Fault Slip on a Major "Overthrust" and Its Implications for Orogenesis

NASA Astrophysics Data System (ADS)

Price, Jason B.; Wernicke, Brian P.; Cosca, Michael A.; Farley, Kenneth A.

2018-03-01

Fifty-one new and 309 published thermochronometric ages (nine systems with closure temperatures ranging from 450 to 70°C) from the Graubünden region of the Central Alps demonstrate that a pronounced thermal mismatch between the Austroalpine allochthon (Alpine "orogenic lid") and the Pennine zone persisted until at least 29 Ma and, allowably, until circa 18 Ma. The observed mismatch supports previous suggestions that the famous "overthrust" between the Austroalpine allochthon and the Pennine zone, historically regarded as primarily an Eocene top-north thrust fault, is in fact primarily an Oligocene-Miocene normal fault that has a minimum of 60 km of displacement with top-south or top-southeast sense of shear. Two hallmarks of Alpine geology, deposition of the foredeep Molasse and emplacement of the Helvetic nappes, appear to be coeval, peripheral manifestations of crustal thickening via the interposition of the Pennine zone as a northward intruding wedge between the Austroalpine "lid" and the European cratonic margin, with the Helvetic system (European margin) acting as the "floor" of the wedge. We presume the Penninic wedge is driven by the buoyant rise of subducted crust no longer able to remain attached to the descending slab. If so, emplacement of the Pennine wedge could have occurred mainly after Adria was juxtaposed against cratonic Europe.

Thermochronometry across the Austroalpine-Pennine boundary, Central Alps, Switzerland: Orogen-perpendicular normal fault slip on a major ‘overthrust’ and its implications for orogenesis

USGS Publications Warehouse

Price, Jason B.; Wernicke, Brian P.; Cosca, Michael A.; Farley, Kenneth A.

2018-01-01

Fifty‐one new and 309 published thermochronometric ages (nine systems with closure temperatures ranging from ~450 to 70°C) from the Graubünden region of the Central Alps demonstrate that a pronounced thermal mismatch between the Austroalpine allochthon (Alpine “orogenic lid”) and the Pennine zone persisted until at least 29 Ma and, allowably, until circa 18 Ma. The observed mismatch supports previous suggestions that the famous “overthrust” between the Austroalpine allochthon and the Pennine zone, historically regarded as primarily an Eocene top‐north thrust fault, is in fact primarily an Oligocene‐Miocene normal fault that has a minimum of 60 km of displacement with top‐south or top‐southeast sense of shear. Two hallmarks of Alpine geology, deposition of the foredeep Molasse and emplacement of the Helvetic nappes, appear to be coeval, peripheral manifestations of crustal thickening via the interposition of the Pennine zone as a northward intruding wedge between the Austroalpine “lid” and the European cratonic margin, with the Helvetic system (European margin) acting as the “floor” of the wedge. We presume the Penninic wedge is driven by the buoyant rise of subducted crust no longer able to remain attached to the descending slab. If so, emplacement of the Pennine wedge could have occurred mainly after Adria was juxtaposed against cratonic Europe.

Kinematic Model for the Sierra Nevada Frontal Fault Zone, California: Paleomagnetism of the Eureka Valley Tuff

NASA Astrophysics Data System (ADS)

Rood, D. H.; Burbank, D. W.; Luyendyk, B. P.

2005-12-01

We document the geometry, timing, rates, and kinematic style of Late Tertiary deformation between Sonora Pass and Mono Basin, central Sierra Nevada, California. Observed mismatches between geodetic and geologic deformation rates in the western Great Basin may be primarily due to underestimates of true geologic deformation. Relatively little attention has been paid to the role of permanent deformation between faults, i.e. folding or crustal block rotation. Current slip discrepancies may be accounted for if a significant component of off-fault transrotational deformation is present. We use geologic and paleomagnetic data to address the kinematic development of the Sierra Nevada frontal fault zone (SNFFZ), and to quantify both the elastic and inelastic strain accumulated across the Sierra Nevada-Basin and Range transition since ~9 Ma. The complex structure of this transition, between the regions of Sonora Pass and Mono Basin, may be a result of three distinct modes of dextral shear accommodation (transtensional, transpressional, and crustal thinning). The study area is characterized by four important structural elements that lie between the SNFFZ and Walker Lane Belt: (1) N- to NNW-striking normal and oblique faults, dominantly E-dipping, and associated W-tilted fault blocks; (2) NW-striking dextral faults; (3) ENE- to NE-striking left-lateral oblique faults that may accommodate overall dextral shear through clockwise vertical axis rotations of fault blocks; (4) E- to NE-trending folds, which may accommodate N-S shortening at large-scale left steps in the dextral transtensional fault system. Between Bridgeport and Mono Basins, a regional E- to NE-trending fold is present that affects both the Tertiary volcanic strata and a Quaternary glacial outwash surface. To the west, normal faulting rates on the SNFFZ are 1-2 mm/yr (Bursik and Sieh, 1989). This slip decreases to the north, into the folded region of the Bodie Hills. This kinematic relationship suggests that the region may be an accommodation zone between two linking faults, possibly an active fold that accommodates N-S shortening at a large-scale left step in the range front fault system. We collected ~200 paleomagnetic samples from the Late Miocene Eureka Valley Tuff of the Stanislaus Group at 21 sites over a 125-km-long, E-W transect (from the Sierra Nevada foothills to east of Mono Basin). Stepwise AF demagnetization reveals a stable characteristic remnant magnetization. Our preliminary data suggest 20-40 degrees of clockwise rotation adjacent to faults of the SNFFZ. An expanded dataset aims to identify specific structural domains, quantify differential vertical axis block rotations, and test geometric models of transrotation (i.e. block-specific versus gradational) during transtensional lithospheric deformation.

Precambrian basement geologic map of Montana; an interpretation of aeromagnetic anomalies

USGS Publications Warehouse

Sims, P.K.; O'Neill, J. M.; Bankey, Viki; Anderson, E.

2004-01-01

Newly compiled aeromagnetic anomaly data of Montana, in conjunction with the known geologic framework of basement rocks, have been combined to produce a new interpretive geologic basement map of Montana. Crystalline basement rocks compose the basement, but are exposed only in the cores of mountain ranges in southwestern Montana. Principal features deduced from the map are: (1) A prominent northeast-trending, 200-km-wide zone of spaced negative anomalies, which extends more than 700 km from southwestern Montana's Beaverhead Mountains to the Canadian border and reflects suturing of the Archean Mexican Hat Block against the Archean Wyoming Province along the Paleoproterozoic Trans-Montana Orogen (new name) at about 1.9-1.8 Ga; (2) North-northwest-trending magnetic lows in northeastern Montana, which reflect the 1.9-1.8 Ga Trans-Hudson Orogen and truncate the older Trans-Montana Zone; and (3) Subtle northwest- and west-trending negative anomalies in central and western Montana, which represent the northernmost segment of brittle-ductile transcurrent faults of the newly recognized Mesoproterozoic Trans-Rocky Mountain fault system. Structures developed in the Proterozoic provided zones of crustal weakness reactivated during younger Proterozoic and Phanerozoic igneous and tectonic activity. For example, the Trans-Montana Zone guided basement involved thrust faulting in southwestern Montana during the Sevier Orogeny. The Boulder Batholith and associated ore deposits and the linear belt of alkaline intrusions to the northeast were localized along a zone of weakness between the Missouri River suture and the Dillon shear zone of the Trans-Montana Orogen. The northwest-trending faults of Trans-Rocky Mountain system outline depocenters for sedimentary rocks in the Belt Basin. This fault system provided zones of weakness that guided Laramide uplifts during basement crustal shortening. Northwest-trending zones have been locally reactivated during Neogene basin-range extension.

The diffuse seismicity of the Sierra Nevada of Santa Marta, the Perijá Range, and south of the La Guajira peninsula, Colombia and Venezuela: Result of the convergence between Caribbean plate and the South American margin during the Late Neogene?

NASA Astrophysics Data System (ADS)

Chicangana, G.; Pedraza, P.; Mora-paez, H.; Ordonez Aristizabal, C. O.; Vargas-Jimenez, C. A.; Kammer, A.

2012-12-01

A diffuse low deep microseismicity located overall between the Guajira peninsula and the Sierra Nevada de Santa Marta (SNSM) was registered with the recent installation (2008 to Present) of three seismological stations in northeastern Colombia by the Colombian Seismological Network (RSNC), but mainly with the Uribia station in (the) central region of La Guajira peninsula, The microseismicity is characterized by a great population of events with 1.2 < Ml < 3.0. and few events of 3.0 < Ml < 4.0 that sporadically occur. The poor number of seismological stations in this region of Colombia impedes to locate the origin of the local seismicity; however, this seismic activity is associated to the tectonic activity of the Oca fault because with the GPS displacement analysis, neotectonics evidence found in faults traces associated to the Oca fault and the historical earthquake that affected the Colombian city of Santa Marta in 1834, lead us to conclude this. This is a big cortical fault that sets the limit between La Guajira peninsula and the SNSM. Its cortical characteristics were verified from geological data together with gravimetric and seismic exploration. The SNSM limits toward the southeast with the Cesar - Ranchería basin, and this basin in turn limits with the Perijá Range that is localized in the Colombia - Venezuela border. The SNSM, Cesar - Ranchería basin and Perijá Range limit toward the southwest with the Bucaramanga - Santa Marta fault (BSMF), the Oca fault toward the north, and Perijá - El Tigre fault toward the southeast defining a pyramidal orogenic complex. Using remote sensing images data with geological and regional geophysical information, we proposed that this orogenic complex was originated as a result of the Panama arc with the northwestern South America accretion. The final adjustment of the Caribbean plate (CP) between North America and South America during the Late Neogene produced the big cortical faults systems activation like Oca - Moron - El Pilar in Colombia and Venezuela toward the south of the Caribbean Plate (CP), and Motegua - Walton - Enriquillo - Plantain Garden toward the north of the CP. This situation was originated of a new subduction development of the Nazca - Cocos plates toward the south and the west of the Panama arc; when this happened, the evolution of the Present - day configuration of the Nazca plate and Galapagos Spreading Center started. From the Early Pliocene, the BSMF and the Oca fault were reactivated: the BSMF, with a left lateral movement, and the Oca fault with a right lateral movement. This last mobility produces the cortical diffuse seismicity that we are showing here.

Investigation of the Hosgri Fault, offshore Southern California, Point Sal to Point Conception

USGS Publications Warehouse

Payne, C.M.; Swanson, O.E.; Schell, B.A.

1979-01-01

A high-resolution seismic reflection survey of the inner continental shelf between Point Sal and Point Conception has revealed faults that displace post-Wisconsin strata (less than 17,000-20,000 years). These faults are the Hosgri fault, the Offshore Lompoc fault, and smaller unnamed faults. Faults trending offshore from the adjacent shoreline such as the Pezzoni, Lions Head, Honda, and Pacifico faults, do not show post-Wisconsin activity. The Hosgri fault trends directly toward the coastline between Purisima Point and Point Arguello where it appears to merge with folds and smaller faults in the western Transverse Ranges. This trend of offshore structures toward the Point Arguello-Point Conception area is consistent with a hypothesis that the regional structural fabric of the southern California Coast Ranges and its adjacent offshore area merge with the Transverse Ranges.

The geology and mineral deposits of part of the western half of the Hailey 1 degree x 2 degrees quadrangle, Idaho; with sections on the Neal mining district and the Dixie mining district

USGS Publications Warehouse

Bennett, Earl H.

2001-01-01

Rocks in the western half of the Hailey 1 ?? 2 ? quadrangle of south-central Idaho include various units of the Atlanta lobe of the Idaho batholith (biotite granodiorite to two-mica granite) of Cretaceous age and plutons and dikes of Tertiary (Eocene to Miocene) age that intrude the batholith. Eocene plutonic rocks consist of a bimodal suite of anorogenic granite and tonalite-granodiorite and hypabyssal rhyolite and rhyodacite dikes. Rocks of the Eocene Challis Volcanics are scarce in the map area but are widespread to the east. Rhyolite ash flows of the Miocene Idavada Volcanics and basalt of the Snake River Plain crop out in the southern part of the area. Lacustrine rocks of probable Eocene to Holocene age are present in the vicinity of Anderson Ranch Reservoir. Quaternary basalts and gravels are widespread on the South Fork of the Boise River, and alluvial deposits are common along active drainages. Metasedimentary rocks of unknown age crop out on House Mountain, Chimney Peak, and on the ridges east of Anderson Ranch Reservoir. Older structures in the Idaho batholith include a major fault beneath House Mountain that may be a decollement for one of the large thrust sheets in eastern Idaho or part of an extensional core complex. The southern part of the Atlanta lobe of the Idaho batholith is cut by northeast-striking faults (parallel with the Trans-Challis fault system) that are related to Eocene extension and by northwest-oriented faults that formed during basin and range extension in the Miocene. The basin and range faults have prominent scarps typical of basin and range topography. The combination of northeast and northwest faults has broken the batholith into a series of rhomboid blocks. Some of these northeast and northwest faults are older structures that were reactivated in the Eocene or Miocene, as indicated by Ar 40 /Ar 39 dates on mineralized rock contained in some of the structures. The Idaho batholith and associated rocks in the map area host several hundred mines and prospects in 18 mining districts. The deposits range in age from Cretaceous to Eocene, and many were developed for precious metals. Most of the deposits are in quartz veins in shear zones in granitic rocks of the batholith. Several districts were actively being explored for low-grade, bulk-minable, precious-metal deposits in the late 1980s and early 1990s.

Drilling to investigate processes in active tectonics and magmatism

NASA Astrophysics Data System (ADS)

Shervais, J.; Evans, J.; Toy, V.; Kirkpatrick, J.; Clarke, A.; Eichelberger, J.

2014-12-01

Coordinated drilling efforts are an important method to investigate active tectonics and magmatic processes related to faults and volcanoes. The US National Science Foundation (NSF) recently sponsored a series of workshops to define the nature of future continental drilling efforts. As part of this series, we convened a workshop to explore how continental scientific drilling can be used to better understand active tectonic and magmatic processes. The workshop, held in Park City, Utah, in May 2013, was attended by 41 investigators from seven countries. Participants were asked to define compelling scientific justifications for examining problems that can be addressed by coordinated programs of continental scientific drilling and related site investigations. They were also asked to evaluate a wide range of proposed drilling projects, based on white papers submitted prior to the workshop. Participants working on faults and fault zone processes highlighted two overarching topics with exciting potential for future scientific drilling research: (1) the seismic cycle and (2) the mechanics and architecture of fault zones. Recommended projects target fundamental mechanical processes and controls on faulting, and range from induced earthquakes and earthquake initiation to investigations of detachment fault mechanics and fluid flow in fault zones. Participants working on active volcanism identified five themes: the volcano eruption cycle; eruption sustainability, near-field stresses, and system recovery; eruption hazards; verification of geophysical models; and interactions with other Earth systems. Recommended projects address problems that are transferrable to other volcanic systems, such as improved methods for identifying eruption history and constraining the rheological structure of shallow caldera regions. Participants working on chemical geodynamics identified four major themes: large igneous provinces (LIPs), ocean islands, continental hotspot tracks and rifts, and convergent plate margins (subduction zones). This workshop brought together a diverse group of scientists with a broad range of scientific experience and interests. A particular strength was the involvement of both early-career scientists, who will initiate and carry out these new research programs, and more senior researchers with many years of experience in scientific drilling and active tectonics research. Each of the themes and questions outlined above has direct benefits to society, including improving hazard assessment, direct monitoring of active systems for early warning, renewable and non-renewable resource and energy exploitation, and predicting the environmental impacts of natural hazards, emphasizing the central role that scientific drilling will play in future scientific and societal developments.

Ring faults and ring dikes around the Orientale basin on the Moon.

PubMed

Andrews-Hanna, Jeffrey C; Head, James W; Johnson, Brandon; Keane, James T; Kiefer, Walter S; McGovern, Patrick J; Neumann, Gregory A; Wieczorek, Mark A; Zuber, Maria T

2018-08-01

The Orientale basin is the youngest and best-preserved multiring impact basin on the Moon, having experienced only modest modification by subsequent impacts and volcanism. Orientale is often treated as the type example of a multiring basin, with three prominent rings outside of the inner depression: the Inner Rook Montes, the Outer Rook Montes, and the Cordillera. Here we use gravity data from NASA's Gravity Recovery and Interior Laboratory (GRAIL) mission to reveal the subsurface structure of Orientale and its ring system. Gradients of the gravity data reveal a continuous ring dike intruded into the Outer Rook along the plane of the fault associated with the ring scarp. The volume of this ring dike is ~18 times greater than the volume of all extrusive mare deposits associated with the basin. The gravity gradient signature of the Cordillera ring indicates an offset along the fault across a shallow density interface, interpreted to be the base of the low-density ejecta blanket. Both gravity gradients and crustal thickness models indicate that the edge of the central cavity is shifted inward relative to the equivalent Inner Rook ring at the surface. Models of the deep basin structure show inflections along the crust-mantle interface at both the Outer Rook and Cordillera rings, indicating that the basin ring faults extend from the surface to at least the base of the crust. Fault dips range from 13-22° for the Cordillera fault in the northeastern quadrant, to 90° for the Outer Rook in the northwestern quadrant. The fault dips for both outer rings are lowest in the northeast, possibly due to the effects of either the direction of projectile motion or regional gradients in pre-impact crustal thickness. Similar ring dikes and ring faults are observed around the majority of lunar basins.

High-Resolution Seismic Reflection Profiling Across the Black Hills Fault, Clark County, Nevada: Preliminary Results

NASA Astrophysics Data System (ADS)

Zaragoza, S. A.; Snelson, C. M.; Jernsletten, J. A.; Saldana, S. C.; Hirsch, A.; McEwan, D.

2005-12-01

The Black Hills fault (BHF) is located in the central Basin and Range Province of western North America, a region that has undergone significant Cenozoic extension. The BHF is an east-dipping normal fault that forms the northwestern structural boundary of the Eldorado basin and lies ~20 km southeast of Las Vegas, Nevada. A recent trench study indicated that the fault offsets Holocene strata, and is capable of producing Mw 6.4-6.8 earthquakes. These estimates indicate a subsurface rupture length at least 10 km greater than the length of the scarp. This poses a significant hazard to structures such as the nearby Hoover Dam Bypass Bridge, which is being built to withstand a Mw 6.2-7.0 earthquake on local faults. If the BHF does continue in the subsurface, this structure, as well as nearby communities (Las Vegas, Boulder City, and Henderson), may not be as safe as previously expected. Previous attempts to image the fault with shallow seismics (hammer source) were inconclusive. However, gravity studies imply that the fault continues south of the scarp. Therefore, a new experiment utilizing high-resolution seismic reflection was performed to image subsurface geologic structures south of the scarp. At each shot point, a stack of four 30-160 Hz vibroseis sweeps of 15 s duration was recorded on a 60-channel system with 40 Hz geophones. This produced two 300 m reflection profiles, with a maximum depth of 500-600 m. A preliminary look at these data indicates the existence of two faults, potentially confirming that the BHF continues in the subsurface south of the scarp.

The lithosphere-asthenosphere boundary beneath the South Island of New Zealand

NASA Astrophysics Data System (ADS)

Hua, Junlin; Fischer, Karen M.; Savage, Martha K.

2018-02-01

Lithosphere-asthenosphere boundary (LAB) properties beneath the South Island of New Zealand have been imaged by Sp receiver function common-conversion point stacking. In this transpressional boundary between the Australian and Pacific plates, dextral offset on the Alpine fault and convergence have occurred for the past 20 My, with the Alpine fault now bounded by Australian plate subduction to the south and Pacific plate subduction to the north. Using data from onland seismometers, especially the 29 broadband stations of the New Zealand permanent seismic network (GeoNet), we obtained 24,971 individual receiver functions by extended-time multi-taper deconvolution, and mapped them to three-dimensional space using a Fresnel zone approximation. Pervasive strong positive Sp phases are observed in the LAB depth range indicated by surface wave tomography. These phases are interpreted as conversions from a velocity decrease across the LAB. In the central South Island, the LAB is observed to be deeper and broader to the northwest of the Alpine fault. The deeper LAB to the northwest of the Alpine fault is consistent with models in which oceanic lithosphere attached to the Australian plate was partially subducted, or models in which the Pacific lithosphere has been underthrust northwest past the Alpine fault. Further north, a zone of thin lithosphere with a strong and vertically localized LAB velocity gradient occurs to the northwest of the fault, juxtaposed against a region of anomalously weak LAB conversions to the southeast of the fault. This structure could be explained by lithospheric blocks with contrasting LAB properties that meet beneath the Alpine fault, or by the effects of Pacific plate subduction. The observed variations in LAB properties indicate strong modification of the LAB by the interplay of convergence and strike-slip deformation along and across this transpressional plate boundary.

Lithosphere-asthenosphere interactions near the San Andreas fault

NASA Astrophysics Data System (ADS)

Chamberlain, C. J.; Houlié, N.; Bentham, H. L. M.; Stern, T. A.

2014-08-01

We decipher the strain history of the upper mantle in California through the comparison of the long-term finite strain field in the mantle and the surface strain-rate field, respectively inferred from fast polarization directions of seismic phases (SKS and SKKS), and Global Positioning System (GPS) surface velocity fields. We show that mantle strain and surface strain-rate fields are consistent in the vicinity of San Andreas Fault (SAF) in California. Such an agreement suggests that the lithosphere and strong asthenosphere have been deformed coherently and steadily since >1 Ma. We find that the crustal stress field rotates (up to 40° of rotation across a 50 km distance from 50° relative to the strike of the SAF, in the near-field of SAF) from San Francisco to the Central Valley. Both observations suggest that the SAF extends to depth, likely through the entire lithosphere. From Central Valley towards the Basin and Range, the orientations of GPS strain-rates, shear wave splitting measurements and seismic stress fields diverge indicating reduced coupling or/and shallow crustal extension and/or presence of frozen anisotropy.

Cyane Fossae

NASA Image and Video Library

2014-07-03

The linear depressions in this image from NASA 2001 Mars Odyssey spacecraft are called graben. Graben are bounded on both sides by faults, and the central material has shifted downward between the faults.

CHARACTER AND REGIONAL SIGNIFICANCE OF GREAT FALLS TECTONIC ZONE, EAST-CENTRAL IDAHO AND WEST-CENTRAL MONTANA.

USGS Publications Warehouse

O'Neill, J. Michael; Lopez, David A.

1985-01-01

The Great Falls tectonic zone, here named, is a belt of diverse northeast-trending geologic features that can be traced from the Idaho batholith in the Cordilleran miogeocline, across thrust-belt structures and basement rocks of west-central and southwestern Montana, through cratonic rocks of central Montana, and into southwestern-most Saskatchewan, Canada. Geologic mapping in east-central Idaho and west-central Montana has outlined a continuous zone of high-angle faults and shear zones. Recurrent fault movement in this zone and strong structural control over igneous intrusion suggest a fundamental tectonic feature that has influenced the tectonic development of the Idaho-Montana area from a least middle Proterozoic time to the present. Refs.

Gravity survey of Dixie Valley, west-central Nevada

USGS Publications Warehouse

Schaefer, Donald H.

1983-01-01

Dixie Valley, a northeast-trending structural trough typical of valleys in the Basin and Range Province, is filled with a maximum of about 10,000 feet of alluvial and lacustrine deposits , as estimated from residual-gravity measurements obtained in this study. On the basis of gravity measurements at 300 stations on nine east-west profiles, the gravity residuals reach a maximum of 30 milligals near the south-central part of the valley. Results from a three-dimensional inversion model indicate that the central depression of the valley is offset to the west of the geographic axis. This offset is probably due to major faulting along the west side of the valley adjacent to the Stillwater Range. Comparison of depths to bedrock obtained during this study and depths obtained from a previous seismic-refraction study indicates a reasonably good correlation. A heterogeneous distribution of densities within the valley-fill deposits would account for differing depths determined by the two methods. (USGS)

Alaska Crustal Deformation: Finite Element Modeling Constrained by Geologic and Very Long Baseline Interferometry Data

NASA Technical Reports Server (NTRS)

Lundgren, Paul; Saucier, Fraancois; Palmer, Randy; Langon, Marc

1995-01-01

We compute crustal motions in Alaska by calculating the finite element solution for an elastic spherical shell problem. The method we use allows the finite element mesh to include faults and very long baseline interferometry (VLBI) baseline rates of change. Boundary conditions include Pacific-North American (PA-NA) plate motions. The solution is constrained by the oblique orientation of the Fairweather-Queen Charlotte strike-slip faults relative to the PA-NA relative motion direction and the oblique orientation from normal convergence of the eastern Aleutian trench fault systems, as well as strike-shp motion along the Denali and Totschunda fault systems. We explore the effects that a range of fault slip constraints and weighting of VLBI rates of change has on the solution. This allows us to test the motion on faults, such as the Denali fault, where there are conflicting reports on its present-day slip rate. We find a pattern of displacements which produce fault motions generally consistent with geologic observations. The motion of the continuum has the general pattern of radial movement of crust to the NE away from the Fairweather-Queen Charlotte fault systems in SE Alaska and Canada. This pattern of crustal motion is absorbed across the Mackenzie Mountains in NW Canada, with strike-slip motion constrained along the Denali and Tintina fault systems. In south central Alaska and the Alaska forearc oblique convergence at the eastern Aleutian trench and the strike-shp motion of the Denali fault system produce a counterclockwise pattern of motion which is partially absorbed along the Contact and related fault systems in southern Alaska and is partially extruded into the Bering Sea and into the forearc parallel the Aleutian trench from the Alaska Peninsula westward. Rates of motion and fault slip are small in western and northern Alaska, but the motions we compute are consistent with the senses of strike-slip motion inferred geologically along the Kaltag, Kobuk Trench, and Thompson Creek faults and with the normal faulting observed in NW Alaska near Nome. The nonrigid behavior of our finite element solution produces patterns of motion that would not have been expected from rigid block models: strike-slip faults can exist in a continuum that has motion mostly perpendicular to their strikes, and faults can exhibit along-strike differences in magnitudes and directions.

Characterization of radon levels in soil and groundwater in the North Maladeta Fault area (Central Pyrenees) and their effects on indoor radon concentration in a thermal spa.

PubMed

Moreno, V; Bach, J; Zarroca, M; Font, Ll; Roqué, C; Linares, R

2018-09-01

Radon levels in the soil and groundwater in the North Maladeta Fault area (located in the Aran Valley sector, Central Pyrenees) are analysed from both geological and radiation protection perspectives. This area is characterized by the presence of two important normal faults: the North Maladeta fault (NMF) and the Tredós Fault (TF). Two primary aspects make this study interesting: (i) the NMF shows geomorphic evidence of neotectonic activity and (ii) the presence of a thermal spa, Banhs de Tredós, which exploits one of the several natural springs of the area and needs to be evaluated for radiation dosing from radon according to the European regulation on basic safety standards for protection against ionizing radiation. The average soil radon and thoron concentrations along a profile perpendicular to the two normal faults - 22 ± 3 kBq·m -3 and 34 ± 3 kBq·m -3 , respectively - are not high and can be compared to the radionuclide content of the granitic rocks of the area, 25 ± 4 Bq·kg -1 for 226 Ra and 38 ± 2 Bq·kg -1 for 224 Ra. However, the hypothesis that the normal faults are still active is supported by the presence of anomalies in both the soil radon and thoron levels that are unlikely to be of local origin together with the presence of similar anomalies in CO 2 fluxes and the fact that the highest groundwater radon values are located close to the normal faults. Additionally, groundwater 222 Rn data have complemented the hydrochemistry data, enabling researchers to better distinguish between water pathways in the granitic and non-granitic aquifers. Indoor radon levels in the spa vary within a wide range, [7-1664] Bq·m -3 because the groundwater used in the treatment rooms is the primary source of radon in the air. Tap water radon levels inside the spa present an average value of 50 ± 8 kBq·m -3 , which does not exceed the level stipulated by the Spanish Nuclear Safety Council (CSN) of 100 kBq·m -3 for water used for human consumption. This finding implies that even relatively low radon concentration values in water can constitute a relevant indoor radon source when the transfer from water to indoor air is efficient. The estimated effective dose range of values for a spa worker due to radon inhalation is [1-9] mSv·y -1 . The use of annual averaged radon concentration values may significantly underestimate the dose in these situations; therefore, a detailed dynamic study must be performed by considering the time that the workers spend in the spa. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterizing the potential for fault reactivation related to CO2 injection through subsurface structural mapping and stress field analysis, Wellington Field, Sumner County, KS

NASA Astrophysics Data System (ADS)

Schwab, D.; Bidgoli, T.; Taylor, M. H.

2015-12-01

South-central Kansas has experienced an unprecedented increase in seismic activity since 2013. The spatial and temporal relationship of the seismicity with brine disposal operations has renewed interest in the role of fluids in fault reactivation. This study focuses on determining the suitability of CO2 injection into a Cambro-Ordovician reservoir for long-term storage and a Mississippian reservoir for enhanced oil recovery in Wellington Field, Sumner County, Kansas. Our approach for determining the potential for induced seismicity has been to (1) map subsurface faults and estimate in-situ stresses, (2) perform slip and dilation tendency analysis to identify optimally-oriented faults relative to the estimated stress field, and (3) monitor surface deformation through cGPS data and InSAR imaging. Through the use of 3D seismic reflection data, 60 near vertical, NNE-striking faults have been identified. The faults range in length from 140-410 m and have vertical separations of 3-32m. A number of faults appear to be restricted to shallow intervals, while others clearly cut the top basement reflector. Drilling-induced tensile fractures (N=78) identified from image logs and inversion of earthquake focal mechanism solutions (N=54) are consistent with the maximum horizontal stress (SHmax) oriented ~E-W. Both strike-slip and normal-slip fault plane solutions for earthquakes near the study area suggest that SHmax and Sv may be similar in magnitude. Estimates of stress magnitudes using step rate tests (Shmin = 2666 psi), density logs (Sv = 5308 psi), and calculations from wells with drilling induced tensile fractures (SHmax = 4547-6655 psi) are determined at the gauge depth of 4869ft. Preliminary slip and dilation tendency analysis indicates that faults striking 0°-20° are stable, whereas faults striking 26°-44° may have a moderate risk for reactivation with increasing pore-fluid pressure.

Preliminary assessment of a previously unknown fault zone beneath the Daytona Beach sand blow cluster near Marianna, Arkansas

USGS Publications Warehouse

Odum, Jackson K.; Williams, Robert; Stephenson, William J.; Tuttle, Martitia P.; Al-Shukri, Hadar

2016-01-01

We collected new high‐resolution P‐wave seismic‐reflection data to explore for possible faults beneath a roughly linear cluster of early to mid‐Holocene earthquake‐induced sand blows to the south of Marianna, Arkansas. The Daytona Beach sand blow deposits are located in east‐central Arkansas about 75 km southwest of Memphis, Tennessee, and about 80 km south of the southwestern end of the New Madrid seismic zone (NMSZ). Previous studies of these sand blows indicate that they were produced between 10,500 and 5350 yr B.P. (before A.D. 1950). The sand blows are large and similar in size to those in the heart of the NMSZ produced by the 1811–1812 earthquakes. The seismic‐reflection profiles reveal a previously unknown zone of near‐vertical faults imaged in the 100–1100‐m depth range that are approximately coincident with a cluster of earthquake‐induced sand blows and a near‐linear surface lineament composed of air photo tonal anomalies. These interpreted faults are expressed as vertical discontinuities with the largest displacement fault showing about 40 m of west‐side‐up displacement at the top of the Paleozoic section at about 1100 m depth. There are about 20 m of folding on reflections within the Eocene strata at 400 m depth. Increasing fault displacement with depth suggests long‐term recurrent faulting. The imaged faults within the vicinity of the numerous sand blow features could be a causative earthquake source, although it does not rule out the possibility of other seismic sources nearby. These newly located faults add to a growing list of potentially active Pleistocene–Holocene faults discovered over the last two decades that are within the Mississippi embayment region but outside of the historical NMSZ.

Regional Survey of Structural Properties and Cementation Patterns of Fault Zones in the Northern Part of the Albuquerque Basin, New Mexico - Implications for Ground-Water Flow

USGS Publications Warehouse

Minor, Scott A.; Hudson, Mark R.

2006-01-01

Motivated by the need to document and evaluate the types and variability of fault zone properties that potentially affect aquifer systems in basins of the middle Rio Grande rift, we systematically characterized structural and cementation properties of exposed fault zones at 176 sites in the northern Albuquerque Basin. A statistical analysis of measurements and observations evaluated four aspects of the fault zones: (1) attitude and displacement, (2) cement, (3) lithology of the host rock or sediment, and (4) character and width of distinctive structural architectural components at the outcrop scale. Three structural architectural components of the fault zones were observed: (1) outer damage zones related to fault growth; these zones typically contain deformation bands, shear fractures, and open extensional fractures, which strike subparallel to the fault and may promote ground-water flow along the fault zone; (2) inner mixed zones composed of variably entrained, disrupted, and dismembered blocks of host sediment; and (3) central fault cores that accommodate most shear strain and in which persistent low- permeability clay-rich rocks likely impede the flow of water across the fault. The lithology of the host rock or sediment influences the structure of the fault zone and the width of its components. Different grain-size distributions and degrees of induration of the host materials produce differences in material strength that lead to variations in width, degree, and style of fracturing and other fault-related deformation. In addition, lithology of the host sediment appears to strongly control the distribution of cement in fault zones. Most faults strike north to north-northeast and dip 55? - 77? east or west, toward the basin center. Most faults exhibit normal slip, and many of these faults have been reactivated by normal-oblique and strike slip. Although measured fault displacements have a broad range, from 0.9 to 4,000 m, most are <100 m, and fault zones appear to have formed mainly at depths less than 1,000 m. Fault zone widths do not exceed 40 m (median width = 15.5 m). The mean width of fault cores (0.1 m) is nearly one order of magnitude less than that of mixed zones (0.75 m) and two orders of magnitude less than that of damage zones (9.7 m). Cements, a proxy for localized flow of ancient ground water, are common along fault zones in the basin. Silica cements are limited to faults that are near and strike north to northwest toward the Jemez volcanic field north of the basin, whereas carbonate fault cements are widely distributed. Coarse sediments (gravel and sand) host the greatest concentrations of cement within fault zones. Cements fill some extension fractures and, to a lesser degree, are concentrated along shear fractures and deformation bands within inner damage zones. Cements are commonly concentrated in mixed zones and inner damage zones on one side of a fault and thus are asymmetrically distributed within a fault zone, but cement does not consistently lie on the basinward side of faults. From observed spatial patterns of asymmetrically distributed fault zone cements, we infer that ancient ground-water flow was commonly localized along, and bounded by, faults in the basin. It is apparent from our study that the Albuquerque Basin contains a high concentration of faults. The geometry of, internal structure of, and cement and clay distribution in fault zones have created and will continue to create considerable heterogeneity of permeability within the basin aquifers. The characteristics and statistical range of fault zone features appear to be predictable and consistent throughout the basin; this predictability can be used in ground-water flow simulations that consider the influence of faults.

Testing fault growth models with low-temperature thermochronology in the northwest Basin and Range, USA

USGS Publications Warehouse

Curry, Magdalena A. E.; Barnes, Jason B.; Colgan, Joseph P.

2016-01-01

Common fault growth models diverge in predicting how faults accumulate displacement and lengthen through time. A paucity of field-based data documenting the lateral component of fault growth hinders our ability to test these models and fully understand how natural fault systems evolve. Here we outline a framework for using apatite (U-Th)/He thermochronology (AHe) to quantify the along-strike growth of faults. To test our framework, we first use a transect in the normal fault-bounded Jackson Mountains in the Nevada Basin and Range Province, then apply the new framework to the adjacent Pine Forest Range. We combine new and existing cross sections with 18 new and 16 existing AHe cooling ages to determine the spatiotemporal variability in footwall exhumation and evaluate models for fault growth. Three age-elevation transects in the Pine Forest Range show that rapid exhumation began along the range-front fault between approximately 15 and 11 Ma at rates of 0.2–0.4 km/Myr, ultimately exhuming approximately 1.5–5 km. The ages of rapid exhumation identified at each transect lie within data uncertainty, indicating concomitant onset of faulting along strike. We show that even in the case of growth by fault-segment linkage, the fault would achieve its modern length within 3–4 Myr of onset. Comparison with the Jackson Mountains highlights the inadequacies of spatially limited sampling. A constant fault-length growth model is the best explanation for our thermochronology results. We advocate that low-temperature thermochronology can be further utilized to better understand and quantify fault growth with broader implications for seismic hazard assessments and the coevolution of faulting and topography.

Soil gas studies along the Trans-Challis fault system near Idaho City, Boise County, Idaho

USGS Publications Warehouse

McCarthy, J.H.; Kiilsgaard, T.H.

2001-01-01

Soil gases were sampled along several traverses that cross the Trans-Challis fault system in central Idaho. Anomalous carbon dioxide, hydrogen, oxygen, hydrocarbon, and sulfur gas concentrations coincide with faults and known mineralized areas. Anomalies in areas not known to be mineralized may reflect undiscovered mineral deposits or concealed faults. Soil gases may be a useful exploration guide for mineral deposits in this terrane.

Structural Mapping Along the Central San Andreas Fault-zone Using Airborne Electromagnetics

NASA Astrophysics Data System (ADS)

Zamudio, K. D.; Bedrosian, P.; Ball, L. B.

2017-12-01

Investigations of active fault zones typically focus on either surface expressions or the associated seismogenic zones. However, the largely aseismic upper kilometer can hold significant insight into fault-zone architecture, strain partitioning, and fault-zone permeability. Geophysical imaging of the first kilometer provides a link between surface fault mapping and seismically-defined fault zones and is particularly important in geologically complex regions with limited surface exposure. Additionally, near surface imaging can provide insight into the impact of faulting on the hydrogeology of the critical zone. Airborne electromagnetic (AEM) methods offer a unique opportunity to collect a spatially-large, detailed dataset in a matter of days, and are used to constrain subsurface resistivity to depths of 500 meters or more. We present initial results from an AEM survey flown over a 60 kilometer long segment of the central San Andreas Fault (SAF). The survey is centered near Parkfield, California, the site of the SAFOD drillhole, which marks the transition between a creeping fault segment to the north and a locked zone to the south. Cross sections with a depth of investigation up to approximately 500 meters highlight the complex Tertiary and Mesozoic geology that is dismembered by the SAF system. Numerous fault-parallel structures are imaged across a more than 10 kilometer wide zone centered on the surface trace. Many of these features can be related to faults and folds within Plio-Miocene sedimentary rocks found on both sides of the fault. Northeast of the fault, rocks of the Mesozoic Franciscan and Great Valley complexes are extremely heterogeneous, with highly resistive volcanic rocks within a more conductive background. The upper 300 meters of a prominent fault-zone conductor, previously imaged to 1-3 kilometers depth by magnetotellurics, is restricted to a 20 kilometer long segment of the fault, but is up to 4 kilometers wide in places. Elevated fault-zone conductivity may be related to damage within the fault zone, Miocene marine shales, or some combination of the two.

Resistivity structures across the Humboldt River basin, north-central Nevada

USGS Publications Warehouse

Rodriguez, Brian D.; Williams, Jackie M.

2002-01-01

Magnetotelluric data collected along five profiles show deep resistivity structures beneath the Battle Mountain-Eureka and Carlin gold trends in north-central Nevada, which appear consistent with tectonic breaks in the crust that possibly served as channels for hydrothermal fluids. It seems likely that gold deposits along these linear trends were, therefore, controlled by deep regional crustal fault systems. Two-dimensional resistivity modeling of the magnetotelluric data generally show resistive (30 to 1,000 ohm-m) crustal blocks broken by sub-vertical, two-dimensional, conductive (1 to 10 ohmm) zones that are indicative of large-scale crustal fault zones. These inferred fault zones are regional in scale, trend northeast-southwest, north-south, and northwest-southeast, and extend to mid-crustal (20 km) depths. The conductors are about 2- to 15-km wide, extend from about 1 to 4 km below the surface to about 20 km depth, and show two-dimensional electrical structure. By connecting the locations of similar trending conductors together, individual regional crustal fault zones within the upper crust can be inferred that range from about 4- to 10-km wide and about 30- to 150-km long. One of these crustal fault zones coincides with the Battle Mountain-Eureka mineral trend. The interpreted electrical property sections also show regional changes in the resistive crust from south to north. Most of the subsurface in the upper 20 km beneath Reese River Valley and southern Boulder Valley are underlain by rock that is generally more conductive than the subsurface beneath Kelly Creek Basin and northern Boulder Valley. This suggests that either elevated-temperature or high-salinity fluids, alteration, or carbonaceous rocks are more pervasive in the more conductive area (Battle Mountain Heat-Flow High), which implies that the crust beneath these valleys is either more fractured or has more carbonaceous rocks than in the area surveyed along the 41st parallel.

On the motion od the Caribbean relative to South-America: New results from GPS geodesy 1999-2012

NASA Astrophysics Data System (ADS)

De La Rosa, R.; Marquez, J.; Bravo, M.; Madriz, Y.; Mencin, D.; Wesnousky, S. G.; Molnar, P. H.; Bilham, R.; Perez, O. J.

2013-05-01

Our previous (1994-2006) collaborative GPS studies in southern Caribbean and northern South-America (SA) show that along its southern boundary in north-central and northeastern Venezuela (Vzla) the Caribbean plate (CP) slips easterly at ~20 mm/a relative to SA, and that in northwestern South-America slip-partitioning takes place resulting in 12 mm/a of dextral motion across the Venezuelan Andes, ~6 mm/a of which occur along the main trace of the NE-trending Bocono fault, and the rest is taken up by SE-subduction of the CP beneath northwestern SA. A series of new velocity vectors obtained in the region from GPS geodesy in 1999-2012 and their corresponding elastic modelings shows that in north-central Vzla part (~3 mm/a) of the C-SA relative dextral shear is taken up by the east-trending continental La Victoria fault, which runs ~50 kms south of San Sebastian fault off-shore and is sub-parallel to it, the later taken up the rest of the motion. The velocity we find for Aruba Is (~20 mm/y due ~east) is consistent with the motion predicted by the Euler pole (61,9° N; 75,7 °W; ω = 0,229 °/Ma) we previously calculated to describe the C-SA relative plate motion. New velocity vectors obtained across the Venezuelan Andes are consistent with a modeled surface velocity due to 12 mm/a of dextral shear below a locking depth of 14 km on one or more vertical N50°E striking faults located within the 100-km wide Andean ranges. The Andes also show a horizontal convergence rate of 2 to 4 mm/a suggesting an uplift rate of ~1.7 mm/a if thrust motion takes place on shallowly dipping faults parallel to the Andes.

Monitoring of hydrogen along the San Andreas and Calaveras faults in central California in 1980-1984

NASA Astrophysics Data System (ADS)

Sato, Motoaki; Sutton, A. J.; McGee, K. A.; Russell-Robinson, Susan

1986-11-01

Hydrogen (H2) has been monitored continuously at 1.5-m depth at nine sites along the San Andreas and Calaveras faults in central California since December 1980. Site characteristic small noninstrumental diurnal variations were recorded during quiescent periods at most sites. Abrupt H2 changes were observed concurrently at two sites on the Calaveras fault; some of these were correlated with oscillatory fault slips. Large (1000-4000 ppm) H2 increases were recorded at some sites on the San Andreas fault between July 1982 and November 1983, which may be correlated with eleven M ≥ 5 earthquakes that occurred near Coalinga during this period. We attribute both the H2 increases and the triggering of the earthquakes to a large-scale compressive stress field within the ductile mafic crust near the plate boundary. The stress perhaps caused bulging of the base of the brittle upper crust and thus caused dilation of the San Andreas fault zone, allowing the escape of pent-up H2 generated by hydration reaction of the mafic crust. At the same time, mobile serpentinites may have squeezed into the seismogenic fault beneath the Coalinga area triggering the earthquakes.

Earthquake and volcano clustering via stress transfer at Yucca Mountain, Nevada

USGS Publications Warehouse

Parsons, T.; Thompson, G.A.; Cogbill, A.H.

2006-01-01

The proposed national high-level nuclear waste repository at Yucca Mountain is close to Quaternary cinder cones and faults with Quaternary slip. Volcano eruption and earthquake frequencies are low, with indications of spatial and temporal clustering, making probabilistic assessments difficult. In an effort to identify the most likely intrusion sites, we based a three-dimensional finite-element model on the expectation that faulting and basalt intrusions are sensitive to the magnitude and orientation of the least principal stress in extensional terranes. We found that in the absence of fault slip, variation in overburden pressure caused a stress state that preferentially favored intrusions at Crater Flat. However, when we allowed central Yucca Mountain faults to slip in the model, we found that magmatic clustering was not favored at Crater Flat or in the central Yucca Mountain block. Instead, we calculated that the stress field was most encouraging to intrusions near fault terminations, consistent with the location of the most recent volcanism at Yucca Mountain, the Lathrop Wells cone. We found this linked fault and magmatic system to be mutually reinforcing in the model in that Lathrop Wells feeder dike inflation favored renewed fault slip. ?? 2006 Geological Society of America.

Vertical-axis rotations and deformation along the active strike-slip El Tigre Fault (Precordillera of San Juan, Argentina) assessed through palaeomagnetism and anisotropy of magnetic susceptibility

NASA Astrophysics Data System (ADS)

Fazzito, Sabrina Y.; Rapalini, Augusto E.; Cortés, José M.; Terrizzano, Carla M.

2017-03-01

Palaeomagnetic data from poorly consolidated to non-consolidated late Cenozoic sediments along the central segment of the active El Tigre Fault (Central-Western Precordillera of the San Juan Province, Argentina) demonstrate broad cumulative deformation up to 450 m from the fault trace and reveal clockwise and anticlockwise vertical-axis rotations of variable magnitude. This deformation has affected in different amounts Miocene to late Pleistocene samples and indicates a complex kinematic pattern. Several inherited linear structures in the shear zone that are oblique to the El Tigre Fault may have acted as block boundary faults. Displacement along these faults may have resulted in a complex pattern of rotations. The maximum magnitude of rotation is a function of the age of the sediments sampled, with largest values corresponding to middle Miocene-lower Pliocene deposits and minimum values obtained from late Pleistocene deposits. The kinematic study is complemented by low-field anisotropy of magnetic susceptibility data to show that the local strain regime suggests a N-S stretching direction, subparallel to the strike of the main fault.

The interplay of fold mechanisms and basement weaknesses at the transition between Laramide basement-involved arches, north-central Wyoming, USA

NASA Astrophysics Data System (ADS)

Neely, Thomas G.; Erslev, Eric A.

2009-09-01

Horizontally-shortened, basement-involved foreland orogens commonly exhibit anastomosing networks of bifurcating basement highs (here called arches) whose structural culminations are linked by complex transition zones of diversely-oriented faults and folds. The 3D geometry and kinematics of the southern Beartooth arch transition zone of north-central Wyoming were studied to understand the fold mechanisms and control on basement-involved arches. Data from 1581 slickensided minor faults are consistent with a single regional shortening direction of 065°. Evidence for oblique-slip, vertical axis rotations and stress refraction at anomalously-oriented folds suggests formation over reactivated pre-existing weaknesses. Restorable cross-sections and 3D surfaces, constrained by surface, well, and seismic data, document blind, ENE-directed basement thrusting and associated thin-skinned backthrusting and folding along the Beartooth and Oregon Basin fault systems. Between these systems, the basement-cored Rattlesnake Mountain backthrust followed basement weaknesses and rotated a basement chip toward the basin before the ENE-directed Line Creek fault system broke through and connected the Beartooth and Oregon Basin fault systems. Slip was transferred at the terminations of the Rattlesnake Mountain fault block by pivoting to the north and tear faulting to the south. In summary, unidirectional Laramide compression and pre-existing basement weaknesses combined with fault-propagation and rotational fault-bend folding to create an irregular yet continuous basement arch transition.

Structural controls on a geothermal system in the Tarutung Basin, north central Sumatra

NASA Astrophysics Data System (ADS)

Nukman, Mochamad; Moeck, Inga

2013-09-01

The Sumatra Fault System provides a unique geologic setting to evaluate the influence of structural controls on geothermal activity. Whereas most of the geothermal systems in Indonesia are controlled by volcanic activity, geothermal systems at the Sumatra Fault System might be controlled by faults and fractures. Exploration strategies for these geothermal systems need to be verified because the typical pattern of heat source and alteration clays are missing so that conventional exploration with magnetotelluric surveys might not provide sufficient data to delineate favorable settings for drilling. We present field geological, structural and geomorphological evidence combined with mapping of geothermal manifestations to allow constraints between fault dynamics and geothermal activity in the Tarutung Basin in north central Sumatra. Our results indicate that the fault pattern in the Tarutung Basin is generated by a compressional stress direction acting at a high angle to the right-lateral Sumatra Fault System. NW-SE striking normal faults possibly related to negative flower structures and NNW-SSE to NNE-SSW oriented dilative Riedel shears are preferential fluid pathways whereas ENE-WSW striking faults act as barriers in this system. The dominant of geothermal manifestations at the eastern part of the basin indicates local extension due to clockwise block rotation in the Sumatra Fault System. Our results support the effort to integrate detailed field geological surveys to refined exploration strategies even in tropical areas where outcrops are limited.

Was Himalayan normal faulting triggered by initiation of the Ramgarh-Munsiari Thrust?

USGS Publications Warehouse

Robinson, Delores M.; Pearson, Ofori N.

2013-01-01

The Ramgarh–Munsiari thrust is a major orogen-scale fault that extends for more than 1,500 km along strike in the Himalayan fold-thrust belt. The fault can be traced along the Himalayan arc from Himachal Pradesh, India, in the west to eastern Bhutan. The fault is located within the Lesser Himalayan tectonostratigraphic zone, and it translated Paleoproterozoic Lesser Himalayan rocks more than 100 km toward the foreland. The Ramgarh–Munsiari thrust is always located in the proximal footwall of the Main Central thrust. Northern exposures (toward the hinterland) of the thrust sheet occur in the footwall of the Main Central thrust at the base of the high Himalaya, and southern exposures (toward the foreland) occur between the Main Boundary thrust and Greater Himalayan klippen. Although the metamorphic grade of rocks within the Ramgarh–Munsiari thrust sheet is not significantly different from that of Greater Himalayan rock in the hanging wall of the overlying Main Central thrust sheet, the tectonostratigraphic origin of the two different thrust sheets is markedly different. The Ramgarh–Munsiari thrust became active in early Miocene time and acted as the roof thrust for a duplex system within Lesser Himalayan rocks. The process of slip transfer from the Main Central thrust to the Ramgarh–Munsiari thrust in early Miocene time and subsequent development of the Lesser Himalayan duplex may have played a role in triggering normal faulting along the South Tibetan Detachment system.

High resolution, multi-2D seismic imaging of Solfatara crater (Campi Flegrei Caldera, southern Italy) from active seismic data

NASA Astrophysics Data System (ADS)

Gammaldi, S.; Amoroso, O.; D'Auria, L.; Zollo, A.

2018-05-01

A multi-2D imaging of the Solfatara Crater inside the Campi Flegrei Caldera, was obtained by the joint interpretation of geophysical evidences and the new active seismic dataset acquired during the RICEN experiment (EU project MEDSUV) in 2014. We used a total of 17,894 first P-wave arrival times manually picked on pre-processed waveforms, recorded along two 1D profiles criss-crossing the inner Solfatara crater, and performed a tomographic inversion based on a multi-scale strategy and a Bayesian estimation of velocity parameters. The resulting tomographic images provide evidence for a low velocity (500-1500 m/s) water saturated deeper layer at West near the outcropping evidence of the Fangaia, contrasted by a high velocity (2000-3200 m/s) layer correlated with a consolidated tephra deposit. The transition velocity range (1500-2000 m/s) layer suggests a possible presence of a gas-rich, accumulation volume. Thanks to the mutual P-wave velocity model, we infer a detailed image for the gas migration path to the Earth surface. The gasses coming from the deep hydrothermal plume accumulate in the central and most depressed area of the Solfatara being trapped by the meteoric water saturated layer. Therefore, the gasses are transmitted through the buried fault toward the east part of the crater, where the ring faults facilitate the release as confirmed by the fumaroles. Starting from the eastern surface evidence of the gas releasing in the Bocca Grande and Bocca Nuova fumaroles, and the presence of the central deeper plume we suggest a fault situated in the central part of the crater which seems to represent the main buried conduit among them plays a key role.

Active tectonic deformation of the western Indian plate boundary: A case study from the Chaman Fault System

NASA Astrophysics Data System (ADS)

Crupa, Wanda E.; Khan, Shuhab D.; Huang, Jingqiu; Khan, Abdul S.; Kasi, Aimal

2017-10-01

Collision of the Eurasian and Indian plates has resulted in two spatially offset subduction zones, the Makran subduction zone to the south and the Himalayan convergent margin to the north. These zones are linked by a system of left-lateral strike-slip faults known as the Chaman Fault System, ∼1200 km, which spans along western Pakistan. Although this is one of the greatest strike-slip faults, yet temporal and spatial variation in displacement has not been adequately defined along this fault system. This study conducted geomorphic and geodetic investigations along the Chaman Fault in a search for evidence of spatial variations in motion. Four study areas were selected over the span of the Chaman Fault: (1) Tarnak-Rud area over the Tarnak-Rud valley, (2) Spinatizha area over the Spinatizha Mountain Range, (3) Nushki area over the Nushki basin, and (4) Kharan area over the northern tip of the Central Makran Mountains. Remote sensing data allowed for in depth mapping of different components and faults within the Kohjak group. Wind and water gap pairs along with offset rivers were identified using high-resolution imagery and digital-elevation models to show displacement for the four study areas. The mountain-front-sinuosity ratio, valley height-to-width-ratio, and the stream-length-gradient index were calculated and used to determine the relative tectonic activity of each area. These geomorphic indices suggest that the Kharan area is the most active and the Tarnak-Rud area is the least active. GPS data were processed into a stable Indian plate reference frame and analyzed. Fault parallel velocity versus fault normal distance yielded a ∼8-10 mm/yr displacement rate along the Chaman Fault just north of the Spinatizha area. InSAR data were also integrated to assess displacement rates along the fault system. Geodetic data support that ultra-slow earthquakes similar to those that strike along other major strike-slip faults, such as the San Andreas Fault System, are possible along the northern segments of the Chaman Fault zone. Geomorphic data suggest that the Chaman Fault along southern part is not very active now but may have gone through high tectonic activity in the past.

Orientations of Pre-existing Structures along the Scarp of the Bilila-Mtakataka Fault in the Central Malawi Rift.

NASA Astrophysics Data System (ADS)

Elifritz, E. A.; Johnson, S.; Beresh, S. C. M.; Mendez, K.; Mynatt, W. G.; Mayle, M.; Laó-Dávila, D. A.; Atekwana, E. A.; Chindandali, P. R. N.; Chisenga, C.; Gondwe, S.; Mkumbwa, M.; Kalindekafe, L.; Kalaguluka, D.; Salima, J.

2017-12-01

The NW-SE Bilila-Mtakataka Fault is suggested to be 100 km in length and is located in the Malawi Rift, a portion of the magma-poor Western Branch of the East African Rift System. This fault is exposed south of Lake Malawi and occurs close to the epicenter of the 1989 6.2 magnitude Salima Earthquake. Moreover, it traverses rocks with inherited Precambrian fabrics that may control the modern rifting process. The effect of the orientation of the pre-existing fabric on the formation of this potentially seismogenic fault has not been well studied. In this project, we measured the older foliations, dikes, and joints in addition to younger faults and striations to understand how the active faulting of the Bilila-Mtakataka Fault is affected by the older fabric. The Fault is divided into 5 segments and 4 linkage zones. All four linkage zones were studied in detail and a Brunton compass was used to determine orientations of structures. The linkage zone between segments 1 and 2 occurs between a regional WNW-ESE joint and the border fault, which is identified by a zig-zag pattern in SRTM data. Precambrian gneiss is cut by oblique steeply-dipping faults in this area. Striations and layer offsets suggest both right-lateral and normal components. This segment strikes NE-SW, in contrast with the NW-SE average strike of the entire fault. The foliations, faults, dikes, and joints collected in this area strike NE-SW, therefore running parallel to the segment. The last 3 southern linkage zones all strike NW-SE and the linkage zone between segment 3 and 4 has a steep dip angle. Dip angles of structures vary from segment to segment, having a wide range of results. Nonetheless, all four linkage zones show structures striking parallel to its segment direction. The results show that pre-existing meso-scale and regional structures and faults strike parallel to the fault scarp. The parallelism of the structures suggest that they serve as planes of weakness, controlling the localization of extension expressed as the border fault. Thus, further studies of the Precambrian foliation in the subsurface are necessary to understand the characterization of the fault where it is unexposed at depth.

Thrust Belt Architecture of the Central and Southern Western Foothills of Taiwan

NASA Astrophysics Data System (ADS)

Rodriguez, F.; Wiltschko, D.

2006-12-01

A structural model of the central and southern Western Foothills Fold and Thrust Belt (WFFTB) was constructed from serial balanced cross sections using available surface, drill, seismic and thermochronologic data. The WFFTB is composed of four main thrust sheets with minor splays. On the east, the Tulungwan fault, which separates the sedimentary rocks of the WFFTB from the low grade meta-sediments of the Slate Belt, evolves from a basement cored fold in the north (around 24°10' N) where the conformable contact between foothills sediments and meta-sediments from the Slate Belt on its western flank is present. At this point the tip of the fault is below the unconformity and the displacement amount is small. To the south this fault breaks the back limb of the fold and gains displacement, and continues gaining displacement to the south. The next thrust sheet to the west includes the Schuantung, Fenghuangchan, Luku, Tatou, Hopiya, and Pingchi faults. This fault system is interpreted as characterized by a long flat with small ramps along a Miocene detachment, not a series of imbricates, as it has been interpreted before. The next thrust sheet to the west is the Chulungupu-Chukou-Lunhou, this system appears to gain displacement to the south as the Schuantung fault system decreases in amount of displacement. The Chulungpu-Chukou-Lunhou fault system contains a wide monocline in the central foothills related with the Chulungpu fault and two wide synclines in the southern part, the Yuching and Tinpligling synclines. Modeling of these two last structures shows that both are uplifted with respect to the regional level above a wide and flat feature; the footwall of the Lunhou fault is a monocline. A geometric solution to lift the Lunhou system involves a major fault-bend-fold anticline with a long ramp and a detachment at ~13 km of depth. It explains, 1) the frontal monocline, which is the from limb of this fault-bend- fold, 2) the minor structures associated with minor back-thrusts and wedging, and 3) the uplift of the structures above the regional level over a wide anticlinal crest. The last thrust system toward the west shows a series of structures which closely associated with the Peikang high implying that the structures are either inversion structures or new thrust faults whose ramps are located in pre-existing normal faults.

Geologic map of the Bodie Hills, California and Nevada

USGS Publications Warehouse

John, David A.; du Bray, Edward A.; Box, Stephen E.; Vikre, Peter G.; Rytuba, James J.; Fleck, Robert J.; Moring, Barry C.

2015-01-01

The Bodie Hills covers about 1,200 km2 straddling the California-Nevada state boundary just north of Mono Lake in the western part of the Basin and Range Province, about 20 km east of the central Sierra Nevada. The area is mostly underlain by the partly overlapping, middle to late Miocene Bodie Hills volcanic field and Pliocene to late Pleistocene Aurora volcanic field (John and others, 2012). Upper Miocene to Pliocene sedimentary deposits, mostly basin-filling sediments, gravel deposits, and fanglomerates, lap onto the west, north, and east sides of the Bodie Hills, where they cover older Miocene volcanic rocks. Quaternary surficial deposits, including extensive colluvial, fluvial, glacial, and lacustrine deposits, locally cover all older rocks. Miocene and younger rocks are tilted ≤30° in variable directions. These rocks are cut by several sets of high-angle faults that exhibit a temporal change from conjugate northeast-striking left-lateral and north-striking right-lateral oblique-slip faults in rocks older than about 9 Ma to north- and northwest-striking dip-slip faults in late Miocene rocks. The youngest faults are north-striking normal and northeast-striking left-lateral oblique-slip faults that cut Pliocene-Pleistocene rocks. Numerous hydrothermal systems were active during Miocene magmatism and formed extensive zones of hydrothermally altered rocks and several large mineral deposits, including gold- and silver-rich veins in the Bodie and Aurora mining districts (Vikre and others, in press).

Paleoseismology of the Chelungpu Fault during the past 1900 years

USGS Publications Warehouse

Chen, W.-S.; Lee, K.-J.; Lee, L.-S.; Ponti, D.J.; Prentice, C.; Chen, Y.-G.; Chang, H.-C.; Lee, Y.-H.

2003-01-01

The 1999 earthquake brought about 80-km-long surface ruptures along the Shihkang, Chelungpu, and Tajienshan Faults, central Taiwan. Several trenches have been excavated across the Chelungpu Fault of the middle segment. The surface ruptures display clear scarps ranging from 0.2 to 4 m high, showing a complex geomorphic pattern due to coseismic faulting and folding. In the study, measurement of the vertical offset or structural relief was taken with reference to the hanging wall beyond the trishear deformation zone. Therefore we suggest that, for the measurement of offset, we should disregard the trishear zone, and that structural relief on the hanging wall should be represented as a real vertical offset. The net slip is then calculated from the structural relief and dip angle of the thrust on a vertical plane along the slip direction. Through the excavation of a pineapple field across the Chelungpu Fault, we are able to provide evidence of at least four earthquake events for the past about 1900 years, including the 1999 earthquake. Furthermore, based on the radiocarbon dates and historical record, the timing of the penultimate event is bracketed to be between 430 and 150 years ago, and the average recurrence interval is less than 700 years. These data indicate that the average slip rate is about 8.7 mm/yr for the past 1900 years. ?? 2003 Published by Elsevier Ltd.

Geologic Map of the Warm Spring Canyon Area, Death Valley National Park, Inyo County, California, With a Discussion of the Regional Significance of the Stratigraphy and Structure

USGS Publications Warehouse

Wrucke, Chester T.; Stone, Paul; Stevens, Calvin H.

2007-01-01

Warm Spring Canyon is located in the southeastern part of the Panamint Range in east-central California, 54 km south of Death Valley National Park headquarters at Furnace Creek Ranch. For the relatively small size of the area mapped (57 km2), an unusual variety of Proterozoic and Phanerozoic rocks is present. The outcrop distribution of these rocks largely resulted from movement on the east-west-striking, south-directed Butte Valley Thrust Fault of Jurassic age. The upper plate of the thrust fault comprises a basement of Paleoproterozoic schist and gneiss overlain by a thick sequence of Mesoproterozoic and Neoproterozoic rocks, the latter of which includes diamictite generally considered to be of glacial origin. The lower plate is composed of Devonian to Permian marine formations overlain by Jurassic volcanic and sedimentary rocks. Late Jurassic or Early Cretaceous plutons intrude rocks of the area, and one pluton intrudes the Butte Valley Thrust Fault. Low-angle detachment faults of presumed Tertiary age underlie large masses of Neoproterozoic dolomite in parts of the area. Movement on these faults predated emplacement of middle Miocene volcanic rocks in deep, east-striking paleovalleys. Excellent exposures of all the rocks and structural features in the area result from sparse vegetation in the dry desert climate and from deep erosion along Warm Spring Canyon and its tributaries.

Structure and Velocities of the Northeastern Santa Cruz Mountains and the Western Santa Clara Valley, California, from the SCSI-LR Seismic Survey

USGS Publications Warehouse

Catchings, R.D.; Goldman, M.R.; Gandhok, G.

2006-01-01

Introduction: The Santa Clara Valley is located in the southern San Francisco Bay area of California and generally includes the area south of the San Francisco Bay between the Santa Cruz Mountains on the southwest and the Diablo Ranges on the northeast. The area has a population of approximately 1.7 million including the city of San Jose, numerous smaller cities, and much of the high-technology manufacturing and research area commonly referred to as the Silicon Valley. Major active strands of the San Andreas Fault system bound the Santa Clara Valley, including the San Andreas fault to the southwest and the Hayward and Calaveras faults to the northeast; related faults likely underlie the alluvium of the valley. This report focuses on subsurface structures of the western Santa Clara Valley and the northeastern Santa Cruz Mountains and their potential effects on earthquake hazards and ground-water resource management in the area. Earthquake hazards and ground-water resources in the Santa Clara Valley are important considerations to California and the Nation because of the valley's preeminence as a major technical and industrial center, proximity to major earthquakes faults, and large population. To assess the earthquake hazards of the Santa Clara Valley better, the U.S. Geological Survey (USGS) has undertaken a program to evaluate potential earthquake sources and potential effects of strong ground shaking within the valley. As part of that program, and to better assess water resources of the valley, the USGS and the Santa Clara Valley Water District (SCVWD) began conducting collaborative studies to characterize the faults, stratigraphy, and structures beneath the alluvial cover of the Santa Clara Valley in the year 2000. Such geologic features are important to both agencies because they directly influence the availability and management of groundwater resources in the valley, and they affect the severity and distribution of strong shaking from local or regional earthquakes sources. As one component of these joint studies, the U. S. Geological Survey acquired more than 28 km of combined seismic reflection/refraction data from the Santa Cruz Mountains to the central Santa Clara Valley in December 2000. The seismic investigation included both high-resolution (~5-m shot and sensor spacing) and relatively lower-resolution (~50-m sensor) seismic surveys from the central Santa Cruz Mountains to the central part of the valley. Collectively, we refer to these seismic investigations as the 2000 western Santa Clara Seismic Investigations (SCSI).

Timing of mid-crustal ductile extension in the northern Snake Range metamorphic core complex, Nevada: Evidence from U/Pb zircon ages

NASA Astrophysics Data System (ADS)

Lee, J.; Blackburn, T.; Johnston, S. M.

2016-12-01

Metamorphic core complexes (Mccs) within the western U.S. record a history of Cenozoic ductile and brittle extensional deformation, metamorphism, and magmatism, and exhumation within the footwall of high-angle Basin and Range normal faults. Documenting these histories within Mccs have been topics of research for over 40 years, yet there remains disagreement about: 1) whether the detachment fault formed and moved at low angles or initiated at high angles and rotated to a low angle; 2) whether brittle and ductile extensional deformation were linked in space and time; and 3) the temporal relationship of both modes of extension to the development of the detachment fault. The northern Snake Range metamorphic core complex (NSR), Nevada has been central to this debate. To address these issues, we report new U/Pb dates from zircon in deformed and undeformed rhyolite dikes emplaced into ductilely thinned and horizontally stretched lower plate rocks that provide tight bounds on the timing of ductile extension at between 38.2 ± 0.3 Ma and 22.50 ± 0.36 Ma. The maximum age constraint is from the Northern dike swarm (NDS), which was emplaced in the northwest part of the range pre- to syn-tectonic with ductile extension. The minimum age constraint is from the Silver Creek dike swarm (SDS) that was emplaced in the southern part of the range post ductile extensional deformation. Our field observations, petrography, and U/Pb zircon ages on the dikes combined with published data on the geology and kinematics of extension, moderate and low temperature thermochronology on lower plate rocks, and age and faulting histories of Cenozoic sedimentary basins adjacent to the NSR are interpreted as recording an episode of localized upper crustal brittle extension during the Eocene that drove upward ductile extensional flow of hot middle crustal rocks from beneath the NSR detachment soon after, or simultaneous with, emplacement of the NDS. Exhumation of the lower plate continued in a rolling hinge/isostatic rebound style; the western part of the lower plate was exhumed first and the eastern part extended ductilely either continuously or episodically until the early Miocene when the post-tectonic SDS was emplaced. Major brittle slip along the eastern part of the NSR detachment and along high angle normal faults exhumed the lower plate during middle Miocene.

New Constraints on Late Pleistocene - Holocene Slip Rates and Seismic Behavior Along the Panamint Valley Fault Zone, Eastern California

NASA Astrophysics Data System (ADS)

Hoffman, W.; Kirby, E.; McDonald, E.; Walker, J.; Gosse, J.

2008-12-01

Space-time patterns of seismic strain release along active fault systems can provide insight into the geodynamics of deforming lithosphere. Along the eastern California shear zone, fault systems south of the Garlock fault appear to have experienced an ongoing pulse of seismic activity over the past ca. 1 kyr (Rockwell et al., 2000). Recently, this cluster of seismicity has been implicated as both cause and consequence of the oft-cited discrepancy between geodetic velocities and geologic slip rates in this region (Dolan et al., 2007; Oskin et al., 2008). Whether other faults within the shear zone exhibit similar behavior remains uncertain. Here we report the preliminary results of new investigations of slip rates and seismic history along the Panamint Valley fault zone (PVFZ). The PVFZ is characterized by dextral, oblique-normal displacement along a moderately to shallowly-dipping range front fault. Previous workers (Zhang et al., 1990) identified a relatively recent surface rupture confined to a ~25 km segment of the southern fault zone and associated with dextral displacements of ~3 m. Our mapping reveals that youthful scarps ranging from 2-4 m in height are distributed along the central portion of the fault zone for at least 50 km. North of Ballarat, a releasing jog in the fault zone forms a 2-3 km long embayment. Displacement of debris-flow levees and channels along NE-striking faults that confirm that displacement is nearly dip-slip, consistent with an overall transport direction toward ~340°, and affording an opportunity to constrain fault displacement directly from the vertical offset of alluvial surfaces of varying age. At the mouth of Happy Canyon, the frontal fault strand displaces a fresh debris-flow by ~3-4 m; soil development atop the debris-flow surface is incipient to negligible. Radiocarbon ages from logs embedded in the flow matrix constrain the timing of the most recent event to younger than ~ 600 cal yr BP. Older alluvial surfaces, such as that buried by the debris-flow lobe, exhibit progressively larger displacement (up to 10-12 m). Well-preserved bar and swale morphology, incipient varnishing of surface boulders, and weak soil development all suggest that this surface is Late Holocene in age. We are working to confirm this inference, but if correct, it suggests that this fault system may have experienced ~3-4 events in the relatively recent past. Finally, preliminary surface ages from even older surfaces along this portion of the fault zone place limits on the slip rate over Late Pleistocene time. Cosmogenic 10Be surface clast dating of an alluvial surface with well-developed pavement and moderate soil development near Happy Canyon suggests a surface age of 30-35 kyr. We are working to refine this estimate with new dating and soil characterization, but our preliminary reconstructions of displacement of this surface across the two primary fault strands are consistent with slip rates that exceed ~3 mm/yr. Overall, these results are consistent with the inference that the Panamint Valley fault zone is the primary structure that accomplishes transfer of right-lateral shear across the Garlock Fault.

Some Key Features of the Strong-Motion Data from the M 6.0 Parkfield, California, Earthquake of 28 September 2004

USGS Publications Warehouse

Shakal, A.; Haddadi, H.; Graizer, V.; Lin, K.; Huang, M.

2006-01-01

The 2004 Parkfield, California, earthquake was recorded by an extensive set of strong-motion instruments well positioned to record details of the motion in the near-fault region, where there has previously been very little recorded data. The strong-motion measurements obtained are highly varied, with significant variations occurring over only a few kilometers. The peak accelerations in the near fault region range from 0.13g to over 1.8g (one of the highest acceleration recorded to date, exceeding the capacity of the recording instrument The largest accelerations occurred near the northwest end of the inferred rupture zone. These motions are consistent with directivity for a fault rupturing from the hypocenter near Gold Hill toward the northwest. However, accelerations up to 0.8g were also observed in the opposite direction, at the south end of the Cholame Valley near Highway 41, consistent with bilateral rupture, with rupture southeast of the hypocenter. Several stations near and over the rupturing fault recorded relatively weak motions, consistent with seemingly paradoxical observations of low shaking damage near strike-slip faults. This event had more ground-motion observations within 10 km of the fault than many other earthquakes combined. At moderate distances peak horizontal ground acceleration (PGA) values dropped off more rapidly with distance than standard relationships. At close-in distance the wide variation of PGA suggests a distance-dependent sigma may be important to consider. The near-fault ground-motion variation is greater than that assumed in ShakeMap interpolations, based on the existing set of observed data. Higher density of stations near faults may be the only means in the near future to reduce uncertainty in the interpolations. Outside of the near-fault zone the variance is closer to that assumed. This set of data provides the first case where near-fault radiation has been observed at an adequate number of stations around the fault to allow detailed study of the fault-normal and fault-parallel motion and the near-field S-wave radiation. The fault-normal motions are significant, but they are not large at the central part of the fault, away from the ends. The fault-normal and fault-parallel motions drop off quite rapidly with distance from the fault. Analysis of directivity indicates increased values of peak velocity in the rupture direction. No such dependence is observed in the peak acceleration, except for stations close to the strike of the fault near and beyond the ends of the faulting.

Gas, slumps and faulting in the Marmara Sea: new results from TAMAM high-resolution seismic reflection data

NASA Astrophysics Data System (ADS)

Shillington, D. J.; Dondurur, D.; Seeber, L.; Steckler, M. S.; Sorlien, C. C.; Diebold, J. B.; Cifci, G.; Gurcay, S.; Okay, S.; Imren, C.; Kurt, H.; Timur, D.; Demirbag, E.

2009-12-01

The Marmara Sea comprises a series of active transtensional basins forming along the North Anatolian Fault (NAF). Both deformation and sedimentation are punctuated by large, destructive earthquakes. Slumping and gas migration also appear to be coupled with these seismotectonic processes. Sediment cores, water column measurements, ROV observations and Chirp data acquired in the Marmara Sea over the last 10 years indicate numerous fluid/gas seeps along active faults, particularly the NAF. Furthermore, some authors infer fluidization and collapse of gas-charged sediments occurred during the 1999 Gulf of Izmit earthquake (farther east along the NAF) based on the presence of mudvolcanoes and slumps after the earthquake. These studies hint at interesting interactions between tectonics, slumping and fluid/gas migration. However, they comprise detailed observations focused on the fault and the upper 20 m of sediments and thus do not provide a complete picture. Here we use a new high-resolution multi-channel seismic (MCS) reflection dataset acquired in the Marmara Sea in July 2008 to elucidate the spatial relationships between gas, slumps and tectonic elements, particularly faults and progressively tilted sediments. The Turkish-American MAmara Multichannel (TAMAM) project involved the acquisition of >2600 km of MCS data throughout the Marmara Sea aboard the R/V K. Piri Reis using a GI gun and a ~450-m-long streamer. We employ several techniques to extract information on the distribution of gas from these data: 1) visual identification of attributes associated with gas (wipe-out zones, high amplitudes, polarity reversals, etc) using a seismic interpretation package, 2) instantaneous attribute analysis (particularly frequency and amplitude), and 3) AVO on select data in shallow water. Many TAMAM profiles exhibit abundant seismic signatures associated with gas. Likewise, many structures are apparent in TAMAM data that may be related to gravitational collapse, and they cover a wide range of sizes, forms, and ages. Possible slumps are observed in our data in the southern portions of the Tekirdag and Cinarcik basins, on both flanks of the Central High, and north of Kumburgaz Basin. Some are clearly non-tectonic, but others may be, and their significance is controversial. Preliminary results from our work suggest that shallow subsurface gas is particularly prevalent in sediments on the Central and Western Highs and in the North Imrali Basin. It occurs in gravitational structures as amplitude anomalies at the apices of waves or blocks. Furthermore, our initial results show abundant gas north of the Imrali Fault and along thrusts associated with the Central and Western highs. Gas is also observed near the NAF. However, gas also occurs away from faults and possible slumps. Our new constraints on the spatial distribution of gas, slumps and shallow faulting from MCS and Chirp data will be used to test competing models for the relationship between these features.

Effects of Arabia-Eurasia Collision on Strike-slip Faults in Central Anatolia?

NASA Astrophysics Data System (ADS)

Whitney, D. L.; Lefebvre, C.; Thomson, S. N.; Idleman, L.; Cosca, M. A.; Kaymakci, N.; Teyssier, C. P.; Umhoefer, P. J.

2013-12-01

The North and East Anatolian faults accommodate much of the tectonic escape of Anatolia in response to Arabia-Eurasia collision and building of the Turkish-Iranian plateau, but these structures formed <10 m.y. ago, at least 25 m.y. after the onset of collision at ~35 Ma. Some of the major strike-slip fault zones located between the North and East Anatolian faults have had long and complex histories of displacement. These faults have deformed, and in some cases exhumed, metamorphic massifs located between fault strands. One example is the Nigde Massif, which was initially exhumed in the Late Cretaceous, then reburied and reheated, along with its overlying sedimentary basin, to a depth of ~10 km at 30 × 5 Ma. Final exhumation and cooling occurred by ~15-17 Ma (massif margin) to ~12 Ma (structurally deepest levels). This depth-temperature-time-deformation history is tracked by a combination of thermobarometric methods, structural and stratigraphic analysis, and geo/thermochronometry (U-Pb zircon, monazite; 40Ar/39Ar hornblende, muscovite, biotite, K-feldspar; zircon and apatite fission-track in metamorphic rocks and basin deposits; and apatite (U-Th)/He). Recent mapping shows the presence of at least two oblique-thrust slices; the structurally higher one accounts for the resetting of detrital apatite fission track and AHe ages in the basin rocks as well as metamorphic apatite near the margin of the massif. The structurally deeper one cuts through the metamorphic basement and explains why mineral lineations and metamorphic assemblages are different along the eastern margin relative to those in the core of the massif. Although the timing of displacement has not been dated directly, low-T thermochronology age and modeling results document a perturbation at ~30 Ma, consistent with the idea that the Ecemis Fault of the Central Anatolian Fault Zone, and probably other pre-existing strike-slip faults in central Anatolia, experienced Late Eocene-Oligocene displacement in response to Arabia-Eurasia collision to the south and SE.

Geophysical and isotopic mapping of preexisting crustal structures that influenced the location and development of the San Jacinto fault zone, southern California

USGS Publications Warehouse

Langenheim, V.E.; Jachens, R.C.; Morton, D.M.; Kistler, R.W.; Matti, J.C.

2004-01-01

We examine the role of preexisting crustal structure within the Peninsular Ranges batholith on determining the location of the San Jacinto fault zone by analysis of geophysical anomalies and initial strontium ratio data. A 1000-km-long boundary within the Peninsular Ranges batholith, separating relatively mafic, dense, and magnetic rocks of the western Peninsular Ranges batholith from the more felsic, less dense, and weakly magnetic rocks of the eastern Peninsular Ranges batholith, strikes north-northwest toward the San Jacinto fault zone. Modeling of the gravity and magnetic field anomalies caused by this boundary indicates that it extends to depths of at least 20 km. The anomalies do not cross the San Jacinto fault zone, but instead trend northwesterly and coincide with the fault zone. A 75-km-long gradient in initial strontium ratios (Sri) in the eastern Peninsular Ranges batholith coincides with the San Jacinto fault zone. Here rocks east of the fault are characterized by Sri greater than 0.706, indicating a source of largely continental crust, sedimentary materials, or different lithosphere. We argue that the physical property contrast produced by the Peninsular Ranges batholith boundary provided a mechanically favorable path for the San Jacinto fault zone, bypassing the San Gorgonio structural knot as slip was transferred from the San Andreas fault 1.0-1.5 Ma. Two historical M6.7 earthquakes may have nucleated along the Peninsular Ranges batholith discontinuity in San Jacinto Valley, suggesting that Peninsular Ranges batholith crustal structure may continue to affect how strain is accommodated along the San Jacinto fault zone. ?? 2004 Geological Society of America.

Seismotectonics and fault structure of the California Central Coast

USGS Publications Warehouse

Hardebeck, Jeanne L.

2010-01-01

I present and interpret new earthquake relocations and focal mechanisms for the California Central Coast. The relocations improve upon catalog locations by using 3D seismic velocity models to account for lateral variations in structure and by using relative arrival times from waveform cross-correlation and double-difference methods to image seismicity features more sharply. Focal mechanisms are computed using ray tracing in the 3D velocity models. Seismicity alignments on the Hosgri fault confirm that it is vertical down to at least 12 km depth, and the focal mechanisms are consistent with right-lateral strike-slip motion on a vertical fault. A prominent, newly observed feature is an ~25 km long linear trend of seismicity running just offshore and parallel to the coastline in the region of Point Buchon, informally named the Shoreline fault. This seismicity trend is accompanied by a linear magnetic anomaly, and both the seismicity and the magnetic anomaly end where they obliquely meet the Hosgri fault. Focal mechanisms indicate that the Shoreline fault is a vertical strike-slip fault. Several seismicity lineations with vertical strike-slip mechanisms are observed in Estero Bay. Events greater than about 10 km depth in Estero Bay, however, exhibit reverse-faulting mechanisms, perhaps reflecting slip at the top of the remnant subducted slab. Strike-slip mechanisms are observed offshore along the Hosgri–San Simeon fault system and onshore along the West Huasna and Rinconada faults, while reverse mechanisms are generally confined to the region between these two systems. This suggests a model in which the reverse faulting is primarily due to restraining left-transfer of right-lateral slip.

Geomorphology, kinematic history, and earthquake behavior of the active Kuwana wedge thrust anticline, central Japan

NASA Astrophysics Data System (ADS)

Ishiyama, Tatsuya; Mueller, Karl; Togo, Masami; Okada, Atsumasa; Takemura, Keiji

2004-12-01

We combine surface mapping of fault and fold scarps that deform late Quaternary alluvial strata with interpretation of a high-resolution seismic reflection profile to develop a kinematic model and determine fault slip rates for an active blind wedge thrust system that underlies Kuwana anticline in central Japan. Surface fold scarps on Kuwana anticline are closely correlated with narrow fold limbs and angular hinges on the seismic profile that suggest at least ˜1.3 km of fault slip completely consumed by folding in the upper 4 km of the crust. The close coincidence and kinematic link between folded terraces and the underlying thrust geometry indicate that Kuwana anticline has accommodated slip at an average rate of 2.2 ± 0.5 mm/yr on a 27°, west dipping thrust fault since early-middle Pleistocene time. In contrast to classical fault bend folds the fault slip budget in the stacked wedge thrusts also indicates that (1) the fault tip propagated upward at a low rate relative to the accrual of fault slip and (2) fault slip is partly absorbed by numerous bedding plane flexural-slip faults above the tips of wedge thrusts. An historic earthquake that occurred on the Kuwana blind thrust system possibly in A.D. 1586 is shown to have produced coseismic surface deformation above the doubly vergent wedge tip. Structural analyses of Kuwana anticline coupled with tectonic geomorphology at 103-105 years timescales illustrate the significance of active folds as indicators of slip on underlying blind thrust faults and thus their otherwise inaccessible seismic hazards.

Stress and Strain Rates from Faults Reconstructed by Earthquakes Relocalization

NASA Astrophysics Data System (ADS)

Morra, G.; Chiaraluce, L.; Di Stefano, R.; Michele, M.; Cambiotti, G.; Yuen, D. A.; Brunsvik, B.

2017-12-01

Recurrence of main earthquakes on the same fault depends on kinematic setting, hosting lithologies and fault geometry and population. Northern and central Italy transitioned from convergence to post-orogenic extension. This has produced a unique and very complex tectonic setting characterized by superimposed normal faults, crossing different geologic domains, that allows to investigate a variety of seismic manifestations. In the past twenty years three seismic sequences (1997 Colfiorito, 2009 L'Aquila and 2016-17 Amatrice-Norcia-Visso) activated a 150km long normal fault system located between the central and northern apennines and allowing the recordings of thousands of seismic events. Both the 1997 and the 2009 main shocks were preceded by a series of small pre-shocks occurring in proximity to the future largest events. It has been proposed and modelled that the seismicity pattern of the two foreshocks sequences was caused by active dilatancy phenomenon, due to fluid flow in the source area. Seismic activity has continued intensively until three events with 6.0

Structural analysis of three extensional detachment faults with data from the 2000 Space-Shuttle Radar Topography Mission

USGS Publications Warehouse

Spencer, J.E.

2010-01-01

The Space-Shuttle Radar Topography Mission provided geologists with a detailed digital elevation model of most of Earth's land surface. This new database is used here for structural analysis of grooved surfaces interpreted to be the exhumed footwalls of three active or recently active extensional detachment faults. Exhumed fault footwalls, each with an areal extent of one hundred to several hundred square kilometers, make up much of Dayman dome in eastern Papua New Guinea, the western Gurla Mandhata massif in the central Himalaya, and the northern Tokorondo Mountains in central Sulawesi, Indonesia. Footwall curvature in profile varies from planar to slightly convex upward at Gurla Mandhata to strongly convex upward at northwestern Dayman dome. Fault curvature decreases away from the trace of the bounding detachment fault in western Dayman dome and in the Tokorondo massif, suggesting footwall flattening (reduction in curvature) following exhumation. Grooves of highly variable wavelength and amplitude reveal extension direction, although structural processes of groove genesis may be diverse.

Interpretation of fault-controlled ramp structures in sedimentary basins - example from Caspian Sea using Landsat TM data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iranpanah, A.

1989-03-01

Lineaments on a series of edge-enhanced images (TM data) from a region around the Caspian Sea form a geomorphically significant linear trend along the major Caucasus-Kopeh Dagh fault line. This fault represents the line of collision between the Cimmerian continents and the Turan plate on the south and north, respectively. The lineament zone manifests a ramp structure that forms a relatively narrow topographic high in the Caspian Sea. Paleogeographic studies of the Caspian Sea suggest that the basin is part of the eastern Paratethys, which began to develop in the early Paleogene during the Alpine-Himalayan uplift. On the basis ofmore » the lineaments and associated geomorphic features, the Caspian Sea can be divided into southern, central, and the northern Caspian subbasins. The Caucasus-Kopeh Dagh fault line trends N80/degrees/W and separates the southern Caspian from the central subbasin, approximately along 40/degrees/N latitude. The boundary between the central and the northern subbasins is also a linear topographic high which trends N70/degrees/E and lies approximately at 44/degrees/N latitude. The southern and central subbasins have subequal areal extension covering 35.64% and the 36.63% of the whole sea, whereas the northern subbasin occupies only 27.73% of the basin.« less

Characterization of the Hosgri Fault Zone and adjacent structures in the offshore Santa Maria Basin, south-central California: Chapter CC of Evolution of sedimentary basins/onshore oil and gas investigations - Santa Maria province

USGS Publications Warehouse

Willingham, C. Richard; Rietman, Jan D.; Heck, Ronald G.; Lettis, William R.

2013-01-01

The Hosgri Fault Zone trends subparallel to the south-central California coast for 110 km from north of Point Estero to south of Purisima Point and forms the eastern margin of the present offshore Santa Maria Basin. Knowledge of the attributes of the Hosgri Fault Zone is important for petroleum development, seismic engineering, and environmental planning in the region. Because it lies offshore along its entire reach, our characterizations of the Hosgri Fault Zone and adjacent structures are primarily based on the analysis of over 10,000 km of common-depth-point marine seismic reflection data collected from a 5,000-km2 area of the central and eastern parts of the offshore Santa Maria Basin. We describe and illustrate the along-strike and downdip geometry of the Hosgri Fault Zone over its entire length and provide examples of interpreted seismic reflection records and a map of the structural trends of the fault zone and adjacent structures in the eastern offshore Santa Maria Basin. The seismic data are integrated with offshore well and seafloor geologic data to describe the age and seismic appearance of offshore geologic units and marker horizons. We develop a basin-wide seismic velocity model for depth conversions and map three major unconformities along the eastern offshore Santa Maria Basin. Accompanying plates include maps that are also presented as figures in the report. Appendix A provides microfossil data from selected wells and appendix B includes uninterpreted copies of the annotated seismic record sections illustrated in the chapter. Features of the Hosgri Fault Zone documented in this investigation are suggestive of both lateral and reverse slip. Characteristics indicative of lateral slip include (1) the linear to curvilinear character of the mapped trace of the fault zone, (2) changes in structural trend along and across the fault zone that diminish in magnitude toward the ends of the fault zone, (3) localized compressional and extensional structures characteristic of constraining and releasing bends and stepovers, (4) changes in the sense and magnitude of vertical separation along strike within the fault zone, and (5) changes in downdip geometry between the major traces and segments of the fault zone. Characteristics indicative of reverse slip include (1) reverse fault geometries that occur across major strands of the fault zone and (2) fault-bend folds and localized thrust faults that occur along the northern and southern reaches of the fault. Analyses of high-resolution, subbottom profiler and side-scan sonar records indicate localized Holocene activity along most of the extent of the fault zone. Collectively, these features are the basis of our characterization of the Hosgri Fault Zone as an active, 110-km-long, convergent right-oblique slip (transpressional) fault with identified northern and southern terminations. This interpretation is consistent with recently published analyses of onshore geologic data, regional tectonic kinematic models, and instrumental seismicity.

Co-seismic Static Stress Drops for Earthquake Ruptures Nucleated on Faults After Progressive Strain Localization

NASA Astrophysics Data System (ADS)

Griffith, W. A.; Nielsen, S.; di Toro, G.; Pollard, D. D.; Pennacchioni, G.

2007-12-01

We estimate the coseismic static stress drop on small exhumed strike-slip faults in the Mt. Abbot quadrangle of the central Sierra Nevada (California). The sub-vertical strike-slip faults cut ~85 Ma granodiorite, were exhumed from 7-10 km depth, and were chosen because they are exposed along their entire lengths, ranging from 8 to 13 m. Net slip is estimated using offset aplite dikes and shallowly plunging slickenlines on the fault surfaces. The faults show a record of progressive strain localization: slip initially nucleated on joints and accumulated from ductile shearing (quartz-bearing mylonites) to brittle slipping (epidote-bearing cataclasites). Thin (< 1 mm) pseudotachylytes associated with the cataclasites have been identified along some faults, suggesting that brittle slip may have been seismic. The brittle contribution to slip may be distinguished from the ductile shearing because epidote-filled, rhombohedral dilational jogs opened at bends and step-overs during brittle slip, are distributed periodically along the length of the faults. We argue that brittle slip occurred along the measured fault lengths in single slip events based on several pieces of evidence. 1) Epidote crystals are randomly oriented and undeformed within dilational jogs, indicating they did not grow during aseismic slip and were not broken after initial opening and precipitation. 2) Opening-mode splay cracks are concentrated near fault tips rather than the fault center, suggesting that the reactivated faults ruptured all at once rather than in smaller slip patches. 3) The fact that the opening lengths of the dilational jogs vary systematically along the fault traces suggests that brittle reactivation occurred in a single slip event along the entire fault rather than in multiple slip events. This unique combination of factors distinguishes this study from previous attempts to estimate stress drop from exhumed faults because we can constrain the coseismic rupture length and slip. The static stress drop is calculated for a circular fault using the length of the mapped faults and their slip distributions as well as the shear modulus of the host granodiorite measured in the laboratory. Calculations yield stress drops on the order of 100-200 MPa, one to two orders of magnitude larger than typical seismological estimates. The studied seismic ruptures occurred along small, deep-seated faults (10 km depth), and, given the fault mineral filling (quartz-bearing mylonites) these were "strong" faults. Our estimates are consistent with static stress drops estimated by Nadeau and Johnson (1998) for small repeated earthquakes.

Hayward Fault, California Interferogram

NASA Image and Video Library

2000-08-17

This image of California Hayward fault is an interferogram created using a pair of images taken by ESA ERS-1 and ERS-2 in June 1992 and September 1997 over the central San Francisco Bay in California.

Multiscale Dynamics of Aseismic Slip on Central San Andreas Fault

NASA Astrophysics Data System (ADS)

Khoshmanesh, M.; Shirzaei, M.

2018-03-01

Understanding the evolution of aseismic slip enables constraining the fault's seismic budget and provides insight into dynamics of creep. Inverting the time series of surface deformation measured along the Central San Andreas Fault obtained from interferometric synthetic aperture radar in combination with measurements of repeating earthquakes, we constrain the spatiotemporal distribution of creep during 1992-2010. We identify a new class of intermediate-term creep rate variations that evolve over decadal scale, releasing stress on the accelerating zone and loading adjacent decelerating patches. We further show that in short-term (<2 year period), creep avalanches, that is, isolated clusters of accelerated aseismic slip with velocities exceeding the long-term rate, govern the dynamics of creep. The statistical properties of these avalanches suggest existence of elevated pore pressure in the fault zone, consistent with laboratory experiments.

An Event-Based Approach to Distributed Diagnosis of Continuous Systems

NASA Technical Reports Server (NTRS)

Daigle, Matthew; Roychoudhurry, Indranil; Biswas, Gautam; Koutsoukos, Xenofon

2010-01-01

Distributed fault diagnosis solutions are becoming necessary due to the complexity of modern engineering systems, and the advent of smart sensors and computing elements. This paper presents a novel event-based approach for distributed diagnosis of abrupt parametric faults in continuous systems, based on a qualitative abstraction of measurement deviations from the nominal behavior. We systematically derive dynamic fault signatures expressed as event-based fault models. We develop a distributed diagnoser design algorithm that uses these models for designing local event-based diagnosers based on global diagnosability analysis. The local diagnosers each generate globally correct diagnosis results locally, without a centralized coordinator, and by communicating a minimal number of measurements between themselves. The proposed approach is applied to a multi-tank system, and results demonstrate a marked improvement in scalability compared to a centralized approach.

Style and rate of quaternary deformation of the Hosgri Fault Zone, offshore south-central coastal California

USGS Publications Warehouse

Hanson, Kathryn L.; Lettis, William R.; McLaren, Marcia; Savage, William U.; Hall, N. Timothy; Keller, Mararget A.

2004-01-01

The Hosgri Fault Zone is the southernmost component of a complex system of right-slip faults in south-central coastal California that includes the San Gregorio, Sur, and San Simeon Faults. We have characterized the contemporary style of faulting along the zone on the basis of an integrated analysis of a broad spectrum of data, including shallow high-resolution and deep penetration seismic reflection data; geologic and geomorphic data along the Hosgri and San Simeon Fault Zones and the intervening San Simeon/Hosgri pull-apart basin; the distribution and nature of near-coast seismicity; regional tectonic kinematics; and comparison of the Hosgri Fault Zone with worldwide strike-slip, oblique-slip, and reverse-slip fault zones. These data show that the modern Hosgri Fault Zone is a convergent right-slip (transpressional) fault having a late Quaternary slip rate of 1 to 3 mm/yr. Evidence supporting predominantly strike-slip deformation includes (1) a long, narrow, linear zone of faulting and associated deformation; (2) the presence of asymmetric flower structures; (3) kinematically consistent localized extensional and compressional deformation at releasing and restraining bends or steps, respectively, in the fault zone; (4) changes in the sense and magnitude of vertical separation both along trend of the fault zone and vertically within the fault zone; (5) strike-slip focal mechanisms along the fault trace; (6) a distribution of seismicity that delineates a high-angle fault extending through the seismogenic crust; (7) high ratios of lateral to vertical slip along the fault zone; and (8) the separation by the fault of two tectonic domains (offshore Santa Maria Basin, onshore Los Osos domain) that are undergoing contrasting styles of deformation and orientations of crustal shortening. The convergent component of slip is evidenced by the deformation of the early-late Pliocene unconformity. In characterizing the style of faulting along the Hosgri Fault Zone, we assessed alternative tectonic models by evaluating (1) the cumulative effects of multiple deformational episodes that can produce complex, difficult-to-interpret fault geometries, patterns, and senses of displacement; (2) the difficult imaging of high-angle fault planes and horizontal fault separations on seismic reflection data; and (3) the effects of strain partitioning that yield coeval strike-slip faults and associated fold and thrust belts.

Faults in parts of north-central and western Houston metropolitan area, Texas

USGS Publications Warehouse

Verbeek, Earl R.; Ratzlaff, Karl W.; Clanton, Uel S.

1979-01-01

Hundreds of residential, commercial, and industrial structures in the Houston metropolitan area have sustained moderate to severe damage owing to their locations on or near active faults. Paved roads have been offset by faults at hundreds of locations, butted pipelines have been distorted by fault movements, and fault-induced gradient changes in drainage lines have raised concern among flood control engineers. Over 150 faults, many of them moving at rates of 0.5 to 2 cm/yr, have been mapped in the Houston area; the number of faults probably far exceeds this figure.This report includes a map of eight faults, in north-central and western Houston, at a scale useful for land-use planning. Seven of the faults, are known, to be active and have caused considerable damage to structures built on or near them. If the eighth fault is active, it may be of concern to new developments on the west side of Houston. A ninth feature shown on the map is regarded only as a possible fault, as an origin by faulting has not been firmly established.Seismic and drill-hold data for some 40 faults, studied in detail by various investigators have verified connections between scarps at the land surface and growth faults in the shallow subsurface. Some scarps, then, are known to be the surface manifestations of faults that have geologically long histories of movement. The degree to which natural geologic processes contribute to current fault movement, however, is unclear, for some of man’s activities may play a role in faulting as well.Evidence that current rates of fault movement far exceed average prehistoric rates and that most offset of the land surface in the Houston area has occurred only within the last 50 years indirectly suggest that fluid withdrawal may be accelerating or reinitiating movement on pre-existing faults. This conclusion, however, is based only on a coincidence in time between increased fault activity and increased rates of withdrawal of water, oil, and gas from subsurface sediments; no cause-and-effect relationship has been demonstrated. An alternative hypothesis is that natural fault movements are characterized by short—term episodicity and that Houston is experiencing the effects of a brief period of accelerated natural fault movement. Available data from monitored faults are insufficient to weigh the relative importance of natural vs. induced fault movements.

Neotectonics and geomorphic evolution of the northwestern arm of the Yellowstone Tectonic Parabola: Controls on intra-cratonic extensional regimes, southwest Montana

USGS Publications Warehouse

Ruleman, Chester A.; Larsen, Mort; Stickney, Michael C.

2014-01-01

The catastrophic Hebgen Lake earthquake of 18 August 1959 (MW 7.3) led many geoscientists to develop new methods to better understand active tectonics in extensional tectonic regimes that address seismic hazards. The Madison Range fault system and adjacent Hebgen Lake–Red Canyon fault system provide an intermountain active tectonic analog for regional analyses of extensional crustal deformation. The Madison Range fault system comprises fault zones (~100 km in length) that have multiple salients and embayments marked by preexisting structures exposed in the footwall. Quaternary tectonic activity rates differ along the length of the fault system, with less displacement to the north. Within the Hebgen Lake basin, the 1959 earthquake is the latest slip event in the Hebgen Lake–Red Canyon fault system and southern Madison Range fault system. Geomorphic and paleoseismic investigations indicate previous faulting events on both fault systems. Surficial geologic mapping and historic seismicity support a coseismic structural linkage between the Madison Range and Hebgen Lake–Red Canyon fault systems. On this trip, we will look at Quaternary surface ruptures that characterize prehistoric earthquake magnitudes. The one-day field trip begins and ends in Bozeman, and includes an overview of the active tectonics within the Madison Valley and Hebgen Lake basin, southwestern Montana. We will also review geologic evidence, which includes new geologic maps and geomorphic analyses that demonstrate preexisting structural controls on surface rupture patterns along the Madison Range and Hebgen Lake–Red Canyon fault systems.

Growth and erosion of mountain ranges at the northeastern margin of Tibet

NASA Astrophysics Data System (ADS)

Hetzel, Ralf; Palumbo, Luigi; Giese, Jörg; Guo, Jianming

2010-05-01

The hypothesis that mountain belts may reach a steady state, in which rock uplift is balanced by erosion, has been supported by numerous field studies and numerical models. The early evolution of mountain ranges, however, and especially the relation between fault growth and topographic response has received little attention. By using a space-for-time substitution we illustrate how active thrust faults and small, fault-bounded mountain ranges evolve into mature mountain chains that will ultimately be incorporated into the laterally growing Tibetan Plateau. At an early stage of development, when faults propagate laterally, slip rates are constant along strike [1-3]. As long as no significant topographic relief has developed, tectonic uplift is at least an order of magnitude faster than the rate of erosion [2,4]. During progressive relief growth and the establishment of drainage basins, erosion of the rising mountain ranges becomes more important, but the studied ranges are still in a pre-steady state and continue to grow both vertically and laterally [5]. During this stage the rate of erosion is linearly correlated to the mean hillslope gradient and the mean local relief, if differences in lithology or rock strength are negligible [6]. The rate of relief growth may be inferred from the difference between local erosion rates on ridge crests and catchment-wide denudation rates [7] - the latter may be taken as a surrogate for the rate of river incision. As hillslopes approach a threshold value, landsliding becomes the dominant process of mass transport and erosion rates increase non-linearly with slope. Once a steady state has been reached, the erosion rate is equal to the rate of rock uplift. A key problem is how the rate of rock uplift can be quantified in such regions, because the stochastic distribution of landslides causes the denudation rates inferred from 10Be in river sediment to be highly variable [8]. References [1] Hetzel et al. (2004). Implications of the fault scaling law for the growth of topography: Mountain ranges in the broken foreland of NE Tibet. Terra Nova 16, 157-162. [2] Hetzel et al. (2002). Low slip rates and long-term preservation of geomorphic features in Central Asia. Nature 417, 428-432. [3] Hetzel et al. (2004). Late Pleistocene/Holocene slip rate of the Zhangye thrust (Qilian Shan, China) and implications for the active growth of the northeastern Tibetan Plateau, Tectonics 23, TC6006, doi:10.1029/2004TC001653. [4] Goethals et al. (2009). Determining the impact of faulting on the rate of erosion in a low-relief landscape: A case study using in situ produced 21Ne on active normal faults in the Bishop Tuff, California. Geomorphology 103, 401-413. [5] Palumbo et al. (2009). Deciphering the rate of mountain growth during topographic presteady state: an example from the NE margin of the Tibetan Plateau. Tectonics 28, TC4017, doi:10.1029/2009TC002455. [6] Palumbo et al. (in press). Topographic and lithologic control on catchment-wide denudation rates derived from cosmogenic 10Be in two mountain ranges at the margin of NE Tibet. Geomorphology, doi:10.1016/j.geomorph.2009.11.019. [7] Meyer et al. (in press). Determining the growth rate of topographic relief using in situ-produced 10Be: A case study in the Black Forest, Germany. Earth and Planetary Science Letters. [8] Densmore et al. (2009). Spatial variations in catchment-averaged denudation rates from normal fault footwalls. Geology 37, 1139-1142.

River profile response to normal fault growth and linkage: an example from the Hellenic forearc of south-central Crete, Greece

NASA Astrophysics Data System (ADS)

Gallen, Sean F.; Wegmann, Karl W.

2017-02-01

Topography is a reflection of the tectonic and geodynamic processes that act to uplift the Earth's surface and the erosional processes that work to return it to base level. Numerous studies have shown that topography is a sensitive recorder of tectonic signals. A quasi-physical understanding of the relationship between river incision and rock uplift has made the analysis of fluvial topography a popular technique for deciphering relative, and some argue absolute, histories of rock uplift. Here we present results from a study of the fluvial topography from south-central Crete, demonstrating that river longitudinal profiles indeed record the relative history of uplift, but several other processes make it difficult to recover quantitative uplift histories. Prior research demonstrates that the south-central coastline of Crete is bound by a large ( ˜ 100 km long) E-W striking composite normal fault system. Marine terraces reveal that it is uplifting between 0.1 and 1.0 mm yr-1. These studies suggest that two normal fault systems, the offshore Ptolemy and onshore South-Central Crete faults, linked together in the recent geologic past (ca. 0.4-1 My BP). Fault mechanics predict that when adjacent faults link into a single fault the uplift rate in footwalls of the linkage zone will increase rapidly. We use this natural experiment to assess the response of river profiles to a temporal jump in uplift rate and to assess the applicability of the stream power incision model to this setting. Using river profile analysis we show that rivers in south-central Crete record the relative uplift history of fault growth and linkage as theory predicts that they should. Calibration of the commonly used stream power incision model shows that the slope exponent, n, is ˜ 0.5, contrary to most studies that find n ≥ 1. Analysis of fluvial knickpoints shows that migration distances are not proportional to upstream contributing drainage area, as predicted by the stream power incision model. Maps of the transformed stream distance variable, χ, indicate that drainage basin instability, drainage divide migration, and river capture events complicate river profile analysis in south-central Crete. Waterfalls are observed in southern Crete and appear to operate under less efficient and different incision mechanics than assumed by the stream power incision model. Drainage area exchange and waterfall formation are argued to obscure linkages between empirically derived metrics and quasi-physical descriptions of river incision, making it difficult to quantitatively interpret rock uplift histories from river profiles in this setting. Karst hydrology, break down of assumed drainage area discharge scaling, and chemical weathering might also contribute to the failure of the stream power incision model to adequately predict the behavior of the fluvial system in south-central Crete.

Multistory duplexes with forward dipping roofs, north central Brooks Range, Alaska

USGS Publications Warehouse

Wallace, W.K.; Moore, Thomas E.; Plafker, G.

1997-01-01

The Endicott Mountains allochthon has been thrust far northward over the North Slope parautochthon in the northern Brooks Range. Progressively younger units are exposed northward within the allochthon. To the south, the incompetent Hunt Fork Shale has thickened internally by asymmetric folds and thrust faults. Northward, the competent Kanayut Conglomerate forms a duplex between a floor thrust in Hunt Fork and a roof thrust in the Kayak Shale. To the north, the competent Lisburne Group forms a duplex between a floor thrust in Kayak and a roof thrust in the Siksikpuk Formation. Both duplexes formed from north vergent detachment folds whose steep limbs were later truncated by south dipping thrust faults that only locally breach immediately overlying roof thrusts. Within the parautochthon, the Kayak, Lisburne, and Siksikpuk-equivalent Echooka Formation form a duplex identical to that in the allochthon. This duplex is succeeded abruptly northward by detachment folds in Lisburne. These folds are parasitic to an anticlinorium interpreted to reflect a fault-bend folded horse in North Slope "basement," with a roof thrust in Kayak and a floor thrust at depth. These structures constitute two northward tapered, internally deformed wedges that are juxtaposed at the base of the allochthon. Within each wedge, competent units have been shortened independently between detachments, located mainly in incompetent units. The basal detachment of each wedge cuts upsection forward (northward) to define a wedge geometry within which units dip regionally forward. These dips reflect forward decrease in internal structural thickening by forward vergent folds and hindward dipping thrust faults. Copyright 1997 by the American Geophysical Union.

Controls on Patterns of Repeated Fault Rupture: Examples From the Denali and Bear River Faults

NASA Astrophysics Data System (ADS)

Schwartz, D. P.; Hecker, S.

2013-12-01

A requirement for estimating seismic hazards is assigning magnitudes to earthquake sources. This relies on anticipating rupture length and slip along faults. Fundamental questions include whether lengths of past surface ruptures can be reasonably determined from fault zone characteristics and whether the variability in length and slip during repeated faulting can be constrained. To address these issues, we look at rupture characteristics and their possible controls from examples in very different tectonic settings: the high slip rate (≥15 mm/yr) Denali fault system, Alaska, and the recently activated Bear River normal fault, Wyoming-Utah. The 2002 rupture of the central Denali fault (CDF) is associated with two noteworthy geometric features. First, rupture initiated where the Susitna Glacier thrust fault (SG) intersects the CDF at depth, near the apex of a structurally complex restraining bend along the Denali. Paleoseismic data show that for the past 700 years the timing of large surface ruptures on the Denali fault west of the 2002 rupture has been distinct from those along the CDF. For the past ~6ka the frequency of SG to Denali ruptures has been ~1:12, indicating that this complexity of the 2002 rupture has not been common. Second, rupture propagated off of one strike-slip fault (CDF) onto another (the Totschunda fault, TF), an occurrence that seldom has been observed. LiDAR mapping of the intersection shows direct connectivity of the two faults--the CDF simply branches into both the TF and the eastern Denali fault (EDF). Differences in the timing of earthquakes during the past 700-800 years at sites surrounding this intersection, and estimates of accumulated slip from slip rates, indicate that for the 2002 rupture sufficient strain had accumulated on the TF to favor its failure. In contrast, the penultimate CDF rupture, with the same slip distribution as in 2002, appears to have stopped at or near the branch point, implying that neither the TF nor the EDF was stressed sufficiently to fail at that time. The Bear River fault zone (BRFZ) is a young normal fault along the eastern margin of basin-range extension that appears to have reactivated a ramp in the Laramide-age Darby-Hogsback thrust. The entire Cenozoic history of the BRFZ may consist of only two surface-rupturing events in the late Holocene (one at ~5 ka and the most recent at ~2.5 ka). The 40-km-long fault comprises synthetic and antithetic scarps extending across a zone up to 5 km wide. Remote sensing, including airborne LiDAR, and field studies show that, despite the complexity, the pattern of faulting was similar (in location and amount) for each of the two events and, at the south end, was strongly influenced by the east-west-trending Uinta Arch. Pre-existing structure clearly has exerted a first-order control on moment release on this immature fault. As shown by these examples, data on timing of surface ruptures, coseismic slip, slip rate, and fault geometry can provide a basis to constrain lengths of past and future earthquake ruptures, including possible alternative rupture scenarios. The difficult question for hazard analysis is whether the available data capture the full range of behavior and with what relative frequency do the alternatives occur?

The geology and ore deposits of Upper Mayflower Gulch, Summit County, Colorado

USGS Publications Warehouse

Randall, John Alexander

1958-01-01

Upper Mayflower Gulch is on the highly glaciated western side of the Tenmile Range near Kokomo in central Colorado. Somewhat less than $500,000 in silver and gold has been produced from the area since the first mining in the 1880' s. In the mapped area high grade regional metamorphism has produced two varieties of gneiss and a granulite. Total thickness of the rocks is about 5,000 feet. Relict bedding is preserved in compositional banding which strikes north to N. 20 ? E. and dips 70 ? to 80 ? southeast. No significant folding was observed. Normal faulting has occurred since the Precambrian; two major sets of faults are recognizable: (1) a set striking N. 70 ? to 85 ? E. and dipping 75?-85 ? NW; and (2) a set striking N. 70?-50 ? W. and dipping 50?-60 ? SW. Tabular bodies of pegmatite and retrogressively metamorphosed schist along many faults indicate Precambrian movement. The Mayflower fault, a 90 to 300 foot wide zone of siltification and shattered rock, strikes about N. 40 ? W. It extends the entire length of the gulch and appears to form the northern terminus for the northeast trending Mosquito Fault. The Mayflower fault shows repeated movement since the Precambrian, totaling about 3,000 feet of apparent dip slip and 640 feet of apparent strike slip. Faulting during the Tertiary includes both additional movement along Precambrian faults and development of shears trending N. to N. 20 ? E. The shears served as channels for the intrusion of two varieties of quartz latite porphyry dikes. Specular hematite and base-metal sulfide mineralization followed intrusion of the porphyry dikes; the minerals were deposited in open fault zones by high temperature solutions in a low pressure environment. The principal metallic minerals in order of deposition are: hematite, pyrite, chalcopyrite, sphalerite, galena, and rarer argentite. The major mines are the Gold Crest, Payrock, Nova Scotia Boy, and Bird's Nest.

Folding associated with extensional faulting: Sheep Range detachment, southern Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guth, P.L.

1985-01-01

The Sheep Range detachment is a major Miocene extensional fault system of the Great Basin. Its major faults have a scoop shape, with straight, N-S traces extending 15-30 km and then abruptly turning to strike E-W. Tertiary deformation involved simultaneous normal faulting, sedimentation, landsliding, and strike-slip faulting. Folds occur in two settings: landslide blocks and drag along major faults. Folds occur in landslide blocks and beneath them. Most folds within landslide blocks are tight anticlines, with limbs dipping 40-60 degrees. Brecciation of the folds and landslide blocks suggests brittle deformation. Near Quijinump Canyon in the Sheep Range, at least threemore » landslide blocks (up to 500 by 1500 m) slid into a small Tertiary basin. Tertiary limestone beneath the Paleozoic blocks was isoclinally folded. Westward dips reveal drag folds along major normal faults, as regional dips are consistently to the east. The Chowderhead anticline is the largest drag fold, along an extensional fault that offsets Ordovician units 8 km. East-dipping Ordovician and Silurian rocks in the Desert Range form the hanging wall. East-dipping Cambrian and Ordovician units in the East Desert Range form the foot wall and east limb of the anticline. Caught along the fault plane, the anticline's west-dipping west limb contains mostly Cambrian units.« less

From Geodetic Imaging of Seismic and Aseismic Fault Slip to Dynamic Modeling of the Seismic Cycle

NASA Astrophysics Data System (ADS)

Avouac, Jean-Philippe

2015-05-01

Understanding the partitioning of seismic and aseismic fault slip is central to seismotectonics as it ultimately determines the seismic potential of faults. Thanks to advances in tectonic geodesy, it is now possible to develop kinematic models of the spatiotemporal evolution of slip over the seismic cycle and to determine the budget of seismic and aseismic slip. Studies of subduction zones and continental faults have shown that aseismic creep is common and sometimes prevalent within the seismogenic depth range. Interseismic coupling is generally observed to be spatially heterogeneous, defining locked patches of stress accumulation, to be released in future earthquakes or aseismic transients, surrounded by creeping areas. Clay-rich tectonites, high temperature, and elevated pore-fluid pressure seem to be key factors promoting aseismic creep. The generally logarithmic time evolution of afterslip is a distinctive feature of creeping faults that suggests a logarithmic dependency of fault friction on slip rate, as observed in laboratory friction experiments. Most faults can be considered to be paved with interlaced patches where the friction law is either rate-strengthening, inhibiting seismic rupture propagation, or rate-weakening, allowing for earthquake nucleation. The rate-weakening patches act as asperities on which stress builds up in the interseismic period; they might rupture collectively in a variety of ways. The pattern of interseismic coupling can help constrain the return period of the maximum- magnitude earthquake based on the requirement that seismic and aseismic slip sum to match long-term slip. Dynamic models of the seismic cycle based on this conceptual model can be tuned to reproduce geodetic and seismological observations. The promise and pitfalls of using such models to assess seismic hazard are discussed.

Numerical Elasto-Plastic Models on the Faulting development in Southwest Taiwan

NASA Astrophysics Data System (ADS)

Lee, F. Y.; Tan, E.; Chang, E. T. Y.

2016-12-01

We use 3D numerical elasto-plastic model to simulate the development of faults and the surface deformation in Southwest Taiwan, which is under oblique collision between Eurasian plate and Philippine Sea plate. The study area is bounded by the Central Range and the Peikang basement high, comprising the southernmost part of the fold-and-thrust belt joint with the coastal plain (mainly the Pingtung Plain). Our goal is to model the deformation mechanism under oblique collision of plates in and around the Taiwan Island. The Cenozoic sediment isopach is taken to form our experimental domain. The Chaochou fault locates at the eastern boundary, serving as a bulldozer moving westward in a velocity of 5 cm/yr. The Peikang high is the backstop at western boundary with material in various friction angle attached to supply friction. The northern boundary striking in E-W direction is at the northern end of the Chaochou fault as a frictional boundary. The southern boundary is in the offshore area of the Pingtung Plain with an open boundary, which allows material free to flow out. A thin layer with variable frictions is at the bottom. Our results show a significant correlation with the tectonic structures observed in the SW Taiwan. The motion velocity increases from north to south, which is similar to the GPS observation. Additionally, two longitudinal thrusts are generated at east. They correspond to the Chaochou fault and Koaping fault, the latter of which is reported as a thrust with sinistral motion. Furthermore, several sinistral strike-slip faults are emergent in the southeast in our experiment. In fact, the bathymetry in the SW offshore Taiwan reveals a lateral motion within the strata in the accretionary prism.

The cooling history and the depth of detachment faulting at the Atlantis Massif oceanic core complex

NASA Astrophysics Data System (ADS)

Schoolmeesters, Nicole; Cheadle, Michael J.; John, Barbara E.; Reiners, Peter W.; Gee, Jeffrey; Grimes, Craig B.

2012-10-01

Oceanic core complexes (OCCs) are domal exposures of oceanic crust and mantle interpreted to be denuded to the seafloor by large slip oceanic detachment faults. We combine previously reported U-Pb zircon crystallization ages with (U-Th)/He zircon thermochronometry and multicomponent magnetic remanence data to determine the cooling history of the footwall to the Atlantis Massif OCC (30°N, MAR) and help establish cooling rates, as well as depths of detachment faulting and gabbro emplacement. We present nine new (U-Th)/He zircon ages for samples from IODP Hole U1309D ranging from 40 to 1415 m below seafloor. These data paired with U-Pb zircon ages and magnetic remanence data constrain cooling rates of gabbroic rocks from the upper 800 m of the central dome at Atlantis Massif as 2895 (+1276/-1162) °C Myr-1 (from ˜780°C to ˜250°C); the lower 600 m of the borehole cooled more slowly at mean rates of ˜500 (+125/-102) °C Myr-1(from ˜780°C to present-day temperatures). Rocks from the uppermost part of the hole also reveal a brief period of slow cooling at rates of ˜300°C Myr-1, possibly due to hydrothermal circulation to ˜4 km depth through the detachment fault zone. Assuming a fault slip rate of 20 mm/yr (from U-Pb zircon ages of surface samples) and a rolling hinge model for the sub-surface fault geometry, we predict that the 780°C isotherm lies at ˜7 km below the axial valley floor, likely corresponding both to the depth at which the semi-brittle detachment fault roots and the probable upper limit of significant gabbro emplacement.

Holocene slip rate for the central Altyn Tagh Fault: Preliminary results from the Tuzidun site based on 14C and 10Be dating of a displaced fluvial terrace riser.

NASA Astrophysics Data System (ADS)

Gold, R. D.; Cowgill, E. S.; Arrowsmith, R.; Muretta, M.; Gosse, J.; Chen, X.; Wang, X.

2007-12-01

The active, left-slip Altyn Tagh Fault (ATF) defines the northern boundary of the Tibetan Plateau and is among the world's longest intracontinental strike-slip faults. Despite a decade of concentrated work, the Holocene slip rate for the central ATF is still disputed, with millennial slip rates derived from faulted landforms ranging from 9 to 27 mm/yr. To address this factor-of-three difference, we are investigating a new slip-rate site near Tuzidun (37.73N, 86.72E) along the Cherchen He reach of the fault. The new site is situated where a south-flowing, ephemeral stream channel crosses the N70E-striking, active trace of the ATF. This channel is flanked by a set of inset fluvial terraces along its eastern bank. North of the ATF, these terraces include both a younger/lower T1 tread and an older/higher T2 terrace, which are vertically separated by an intervening T2/T1 riser. South of the fault, the stream is inset into an alluvial fan, F1. The F1 fan is separated from the higher, T2 fluvial terrace tread to the east, by the T2/F1 riser. Our neotectonic mapping and survey data indicate that the T2/F1 riser on the south/downstream side of the ATF and the T2/T1 riser on the north/upstream side have been displaced from one another by left slip along the ATF. The present separation between these riser segments is ~56 m, though lateral erosion of the riser may have diminished the true offset. To account for this possibility, we have developed three end-member reconstructions that yield offsets ranging from 56 to105 m. Ongoing geochronologic and geomorphic analyses are designed further limit the range of possible displacements. Preliminary age analyses from the Tuzidun site include 22 new radiocarbon dates from buried organic materials and 7 analyses of 10Be concentration in quartz extracted from amalgamated samples of terrace conglomerates. The 14C analyses are from samples collected from within the T2 tread on both sides of the ATF and from loess deposits that cap the downstream T2/F1 riser face. The 10Be analyses are from samples collected in two depth profiles, north and south of the ATF, dug into the T2 deposit at the crest of the displaced riser. The calibrated 14C dates and 10Be surface-exposure ages are compatible, and indicate that the surfaces at the crest and toe of the riser were abandoned at ~6 ka and ~4.4 ka, respectively. To bracket the millennial slip rate at this site, we consider three end-member reconstructions. The first is an upper-terrace reconstruction, in which the riser started recording displacement as soon as the upper-terrace, T2, was abandoned, providing a minimum constraint on the slip rate of ~9 mm/yr since ~6 ka. An intermediate interpretation is a lower-terrace reconstruction, in which the riser accumulated no displacement until the lower surface, F1, was abandoned, yielding a slip rate of ~13 mm/yr since ~4.4 ka. The final reconstruction is one in which erosion of the upstream T2 surface, prior to T1/F1 deposition, diminished the present-day observed offset. In this case, up to 105 m of displacement has occurred since abandonment of the T2 surface, which permits a slip rate as high as ~18 mm/yr since ~6 ka. The new slip rate of 9-18 mm/yr for the Tuzidun site is consistent with our preliminary results from three additional slip-rate sites along the central ATF, and taken together, provides an upper limit of 18 mm/yr for the Holocene slip rate along this reach of the fault.

Strain Localisation at Rift Segment Boundaries: An Example from the Bocana Transfer Zone in Central Baja California, Mexico

NASA Astrophysics Data System (ADS)

Seiler, C.; Gleadow, A. J.; Kohn, B. P.

2012-12-01

Rifts are commonly segmented into several hundred kilometre long zones of opposing upper-plate transport direction with boundaries defined by accommodation and transfer zones. A number of such rift segments have been recognized in the northern Gulf of California, a youthful oceanic basin that is currently undergoing the rift-drift transition. However, detailed field studies have so far failed to identify suitable structures that could accommodate the obvious deformation gradients between different rift segments, and the nature of strain transfer at segment boundaries remains enigmatic. The situation is even less clear in central and southern Baja California, where a number of rift segments have been hypothesized but it is unknown whether the intervening segment boundaries facilitate true reversals in the upper-plate transport direction, or whether they simply accommodate differences in the timing, style or magnitude of deformation. The Bocana transfer zone (BTZ) in central Baja California is a linear, WNW-ESE striking structural discontinuity separating two rift segments with different magnitudes and styles of extensional deformation. North of the BTZ, the Libertad fault is part of the Main Gulf Escarpment, which represents the breakaway fault that separates the Gulf of California rift to the east from the relatively stable western portion of the Baja peninsula. The N-striking Libertad escarpment developed during the Late Miocene (~10-8Ma) and exhibits a topographic relief of ca. 1,000m along a strike-length of ca. 50km. Finite displacement decreases from ~1000m in the central fault segment to ~500m further south, where the fault bends SE and merges with the BTZ. In the hanging wall of the Libertad fault, a series of W-tilted horsts are bound along their eastern margins by two moderate-displacement E-dipping normal faults. South of the BTZ, extension was much less than further north, which explains the comparatively subdued relief and generally shallower tilt of pre-rift strata in this area. The BTZ itself is characterized by two en echelon WNW-ESE striking dextral-oblique transfer faults with a significant down-to-the-NNE extensional component. Strain is transferred from the Libertad breakaway fault onto the transfer faults over a distance of >20km through a network of interacting normal, oblique and strike-slip faults. The shape, location and orientation of the main faults were strongly influenced by pre-existing rheological heterogeneities. Major normal faults are parallel to either the Mesozoic metamorphic foliation or Cretaceous intrusive contacts, and developed where the foliation was at a high angle to the extension direction. In contrast, the oblique-slip faults of the BTZ formed parallel to the metamorphic foliation where formlines are at a small angle to the regional extension direction. Compared to other, less well-understood accommodation zones in the Gulf of California rift, the BTZ shows a distinct lack of volcanic activity, which may help explain the different exposure and structural expression of the various segment boundaries.

Modeling fluid flow and heat transfer at Basin and Range faults: preliminary results for Leach hot springs, Nevada

USGS Publications Warehouse

López, Dina L.; Smith, Leslie; Storey, Michael L.; Nielson, Dennis L.

1994-01-01

The hydrothermal systems of the Basin and Range Province are often located at or near major range bounding normal faults. The flow of fluid and energy at these faults is affected by the advective transfer of heat and fluid from an to the adjacent mountain ranges and valleys, This paper addresses the effect of the exchange of fluid and energy between the country rock, the valley fill sediments, and the fault zone, on the fluid and heat flow regimes at the fault plane. For comparative purposes, the conditions simulated are patterned on Leach Hot Springs in southern Grass Valley, Nevada. Our simulations indicated that convection can exist at the fault plane even when the fault is exchanging significant heat and fluid with the surrounding country rock and valley fill sediments. The temperature at the base of the fault decreased with increasing permeability of the country rock. Higher groundwater discharge from the fault and lower temperatures at the base of the fault are favored by high country rock permabilities and fault transmissivities. Preliminary results suggest that basal temperatures and flow rates for Leach Hot Springs can not be simulated with a fault 3 km deep and an average regional heat flow of 150 mW/m2 because the basal temperature and mass discharge rates are too low. A fault permeable to greater depths or a higher regional heat flow may be indicated for these springs.

The Kumamoto Mw7.1 mainshock: deep initiation triggered by the shallow foreshocks

NASA Astrophysics Data System (ADS)

Shi, Q.; Wei, S.

2017-12-01

The Kumamoto Mw7.1 earthquake and its Mw6.2 foreshock struck the central Kyushu region in mid-April, 2016. The surface ruptures are characterized with multiple fault segments and a mix of strike-slip and normal motion extended from the intersection area of Hinagu and Futagawa faults to the southwest of Mt. Aso. Despite complex surface ruptures, most of the finite fault inversions use two fault segments to approximate the fault geometry. To study the rupture process and the complex fault geometry of this earthquake, we performed a multiple point source inversion for the mainshock using the data on 93 K-net and Kik-net stations. With path calibration from the Mw6.0 foreshock, we selected the frequency ranges for the Pnl waves (0.02 0.26 Hz) and surface waves (0.02 0.12 Hz), as well as the components that can be well modeled with the 1D velocity model. Our four-point-source results reveal a unilateral rupture towards Mt. Aso and varying fault geometries. The first sub-event is a high angle ( 79°) right-lateral strike-slip event at the depth of 16 km on the north end of the Hinagu fault. Notably the two M>6 foreshocks is located by our previous studies near the north end of the Hinagu fault at the depth of 5 9 km, which may give rise to the stress concentration at depth. The following three sub-events are distributed along the surface rupture of the Futagawa fault, with focal depths within 4 10 km. Their focal mechanisms present similar right-lateral fault slips with relatively small dip angles (62 67°) and apparent normal-fault component. Thus, the mainshock rupture initiated from the relatively deep part of the Hinagu fault and propagated through the fault-bend toward NE along the relatively shallow part of the Futagawa fault until it was terminated near Mt. Aso. Based on the four-point-source solution, we conducted a finite-fault inversion and obtained a kinematic rupture model of the mainshock. We then performed the Coulomb Stress analyses on the two foreshocks and the mainshock. The results support that the stress alternation after the foreshocks may have triggered the failure on the fault plane of the Mw7.1 earthquake. Therefore, the 2016 Kumamoto earthquake sequence is dominated by a series of large triggering events whose initiation is associated with the geometric barrier in the intersection of the Futagawa and Hinagu faults.

Subsidence Induced Faulting Hazard Zonation Using Persistent Scatterer Interferometry and Horizontal Gradient Mapping in Mexican Urban Areas

NASA Astrophysics Data System (ADS)

Cabral-Cano, E.; Cigna, F.; Osmanoglu, B.; Dixon, T.; Wdowinski, S.

2011-12-01

Subsidence and faulting have affected Mexico city for more than a century and the process is becoming widespread throughout larger urban areas in central Mexico. This process causes substantial damages to the urban infrastructure and housing structures and will certainly become a major factor to be considered when planning urban development, land use zoning and hazard mitigation strategies in the next decades. Subsidence is usually associated with aggressive groundwater extraction rates and a general decrease of aquifer static level that promotes soil consolidation, deformation and ultimately, surface faulting. However, local stratigraphic and structural conditions also play an important role in the development and extension of faults. In all studied cases stratigraphy of the uppermost sediment strata and the structure of the underlying volcanic rocks impose a much different subsidence pattern which is most suitable for imaging through satellite geodetic techniques. We present examples from several cities in central Mexico: a) Mexico-Chalco. Very high rates of subsidence, up to 370 mm/yr are observed within this lacustrine environment surrounded by Pliocene-Quaternary volcanic structures. b) Aguascalientes where rates up to 90 mm/yr in the past decade are observed, is controlled by a stair stepped N-S trending graben that induces nucleation of faults along the edges of contrasting sediment package thicknesses. c) Morelia presents subsidence rates as high as 80 mm/yr. Differential deformation is observed across major basin-bounding E-W trending faults and with higher subsidence rates on their hanging walls, where the thickest sequences of compressible Quaternary sediments crop out. Our subsidence and faulting study in urban areas of central Mexico is based on a horizontal gradient analysis using displacement maps from Persistent Scatterer InSAR that allows definition of areas with high vulnerability to surface faulting. Correlation of the surface subsidence pattern through satellite geodesy and surface faults show that the principal factor for defining these hazardous areas is best determined not by solely using the subsidence magnitude rates but rather by using a combined magnitude and horizontal subsidence gradient analysis. This approach is used as the basis for the generation of subsidence-induced surface faulting hazard maps for the studied urban areas.

Miocene extension in the East Range, Nevada: A two-stage history of normal faulting in the northern basin and range

USGS Publications Warehouse

Fosdick, J.C.; Colgan, J.P.

2008-01-01

The East Range in northwestern Nevada is a large, east-tilted crustal block bounded by west-dipping normal faults. Detailed mapping of Tertiary stratigraphic units demonstrates a two-phase history of faulting and extension. The oldest sedimentary and volcanic rocks in the area record cumulative tilting of -30??-45??E, whereas younger olivine basalt flows indicate only a 15??-20??E tilt since ca. 17-13 Ma. Cumulative fault slip during these two episodes caused a minimum of 40% extensional strain across the East Range, and Quaternary fault scarps and seismic activity indicate that fault motion has continued to the present day. Apatite fission track and (U-Th)/He data presented here show that faulting began in the East Range ca. 17-15 Ma, coeval with middle Miocene extension that occurred across much of the Basin and Range. This phase of extension occurred contemporaneously with middle Miocene volcanism related to the nearby northern Nevada rifts, suggesting a link between magmatism and extensional stresses in the crust that facilitated normal faulting in the East Range. Younger fault slip, although less well constrained, began after 10 Ma and is synchronous with the onset of low-magnitude extension in many parts of northwestern Nevada and eastern California. These findings imply that, rather than migrating west across a discrete boundary, late Miocene extension in western Nevada is a distinct, younger period of faulting that is superimposed on the older, middle Miocene distribution of extended and unextended domains. The partitioning of such middle Miocene deformation may reflect the influence of localized heterogeneities in crustal structure, whereas the more broadly distributed late Miocene extension may reflect a stronger influence from regional plate boundary processes that began in the late Miocene. ?? 2008 Geological Society of America.

Lacustrine Paleoseismology Reveals Earthquake Segmentation of the Alpine Fault, New Zealand

NASA Astrophysics Data System (ADS)

Howarth, J. D.; Fitzsimons, S.; Norris, R.; Langridge, R. M.

2013-12-01

Transform plate boundary faults accommodate high rates of strain and are capable of producing large (Mw>7.0) to great (Mw>8.0) earthquakes that pose significant seismic hazard. The Alpine Fault in New Zealand is one of the longest, straightest and fastest slipping plate boundary transform faults on Earth and produces earthquakes at quasi-periodic intervals. Theoretically, the fault's linearity, isolation from other faults and quasi-periodicity should promote the generation of earthquakes that have similar magnitudes over multiple seismic cycles. We test the hypothesis that the Alpine Fault produces quasi-regular earthquakes that contiguously rupture the southern and central fault segments, using a novel lacustrine paleoseismic proxy to reconstruct spatial and temporal patterns of fault rupture over the last 2000 years. In three lakes located close to the Alpine Fault the last nine earthquakes are recorded as megaturbidites formed by co-seismic subaqueous slope failures, which occur when shaking exceeds Modified Mercalli (MM) VII. When the fault ruptures adjacent to a lake the co-seismic megaturbidites are overlain by stacks of turbidites produced by enhanced fluvial sediment fluxes from earthquake-induced landslides. The turbidite stacks record shaking intensities of MM>IX in the lake catchments and can be used to map the spatial location of fault rupture. The lake records can be dated precisely, facilitating meaningful along strike correlations, and the continuous records allow earthquakes closely spaced in time on adjacent fault segments to be distinguished. The results show that while multi-segment ruptures of the Alpine Fault occurred during most seismic cycles, sequential earthquakes on adjacent segments and single segment ruptures have also occurred. The complexity of the fault rupture pattern suggests that the subtle variations in fault geometry, sense of motion and slip rate that have been used to distinguish the central and southern segments of the Alpine Fault can inhibit rupture propagation, producing a soft earthquake segment boundary. The study demonstrates the utility of lakes as paleoseismometers that can be used to reconstruct the spatial and temporal patterns of earthquakes on a fault.

Novel Coupled Thermochronometric and Geochemical Investigation of Blind Geothermal Resources in Fault-Controlled Dilational Corners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stockli, Daniel

Geothermal plays in extensional and transtensional tectonic environments have long been a major target in the exploration of geothermal resources and the Dixie Valley area has served as a classic natural laboratory for this type of geothermal plays. In recent years, the interactions between normal faults and strike-slip faults, acting either as strain relay zones have attracted significant interest in geothermal exploration as they commonly result in fault-controlled dilational corners with enhanced fracture permeability and thus have the potential to host blind geothermal prospects. Structural ambiguity, complications in fault linkage, etc. often make the selection for geothermal exploration drilling targetsmore » complicated and risky. Though simplistic, the three main ingredients of a viable utility-grade geothermal resource are heat, fluids, and permeability. Our new geological mapping and fault kinematic analysis derived a structural model suggest a two-stage structural evolution with (a) middle Miocene N -S trending normal faults (faults cutting across the modern range), - and tiling Olio-Miocene volcanic and sedimentary sequences (similar in style to East Range and S Stillwater Range). NE-trending range-front normal faulting initiated during the Pliocene and are both truncating N-S trending normal faults and reactivating some former normal faults in a right-lateral fashion. Thus the two main fundamental differences to previous structural models are (1) N-S trending faults are pre-existing middle Miocene normal faults and (2) these faults are reactivated in a right-later fashion (NOT left-lateral) and kinematically linked to the younger NE-trending range-bounding normal faults (Pliocene in age). More importantly, this study provides the first constraints on transient fluid flow through the novel application of apatite (U-Th)/He (AHe) and 4He/ 3He thermochronometry in the geothermally active Dixie Valley area in Nevada.« less

Is the Marmara Sea segment of the North Anatolian Fault Creeping or loading ?

NASA Astrophysics Data System (ADS)

Klein, Emilie; Masson, Frédéric; Duputel, Zacharie; Yavasoglu, Hakan

2016-04-01

During the last century, the North Anatolian Fault has experienced a migrating Mw>7 earthquakes sequence that ruptured about 1000 km of the fault westward. The last major earthquakes occurred in 1999 in Izmit (Mw7.4) and Duzce (Mw7.2). Only the segments located directly offshore of Istanbul, in the Marmara Sea, remain unbroken in this series of events. This region represents a major issue in terms of seismic hazard with more than 13 millions inhabitants in the city of Istanbul. However, a strong controversy remains over whether the central segment of the Main Marmara Fault is locked and likely to experience a major earthquake, or not. Recent studies based on geodetic data suggest indeed that, contrary to the Prince's Island segment which is fully locked, the central segment is accommodating the strain by aseismic fault creep. So it has not the potential to generate a Mw ~7 event. These results, mostly based on relatively simple strain accumulation models over infinitely long faults, is contested by a recent seismic data study, which suggests on the contrary that this fault segment is fully locked and mature to generate such a great earthquake. In this study, we revisit the available geodetic data considering a 3D geometry of the fault, allowing to take into account the lateral variations of behavior along the fault. In particular, we evaluate if current geodetic datasets are sufficient to constrain strain accumulation and thus to conclude about the seismic hazard in the region.

Identifying block structure in the Pacific Northwest, USA

USGS Publications Warehouse

Savage, James C.; Wells, Ray E.

2015-01-01

We have identified block structure in the Pacific Northwest (west of 116°W between 38°N and 49°N) by clustering GPS stations so that the same Euler vector approximates the velocity of each station in a cluster. Given the total number k of clusters desired, the clustering procedure finds the best assignment of stations to clusters. Clustering is calculated for k= 2 to 14. In geographic space, cluster boundaries that remain relatively stable as k is increased are tentatively identified as block boundaries. That identification is reinforced if the cluster boundary coincides with a geologic feature. Boundaries identified in northern California and Nevada are the Central Nevada Seismic Belt, the west side of the Northern Walker Lane Belt, and the Bartlett Springs Fault. Three blocks cover all of Oregon and Washington. The principal block boundary there extends west-northwest along the Brothers Fault Zone, then north and northwest along the eastern boundary of Siletzia, the accreted oceanic basement of the forearc. East of this boundary is the Intermountain block, its eastern boundary undefined. A cluster boundary at Cape Blanco subdivides the forearc along the faulted southern margin of Siletzia. South of Cape Blanco the Klamath Mountains-Basin and Range block extends east to the Central Nevada Seismic Belt and south to the Sierra Nevada-Great Valley block. The Siletzia block north of Cape Blanco coincides almost exactly with the accreted Siletz terrane. The cluster boundary in the eastern Olympic Peninsula may mark permanent shortening of Siletzia against the Intermountain block.

Geodetic measurement of deformation in the central Mojave Desert, California

NASA Technical Reports Server (NTRS)

Sauber, Jeanne; Solomon, Sean C.; Thatcher, Wayne

1986-01-01

Data from triangulation and trilateration surveys made during 1934-1982 are used to calculate shear strain rates in the central Mojave Desert of California. For the region between the Helendale and Camp Rock faults the shear strain rate was determined to be 0.16 + or - 0.03 microstrain/yr, with maximum right-lateral shear strain occurring on a plane oriented N41 deg W + or - 5 deg. If this deformation is due to right-lateral motion across the northwest trending local faults, the average shear straining corresponds to a relative displacement of 6.7 + or - 1.3 mm/yr across this portion of the network, accounting for about 12 percent of the predicted 56 mm/yr of relative motion between the North Atlantic and Pacific plates. From the Camp Rock fault eastward across the network there is a transition from significant to very low strain rates. Examination of nine focal mechanisms and their relation to the local geology and the strain data suggests that most of the long-term displacement occurs on the major northwest trending faults oriented nearly along the direction of relative motion between the North American and Pacific plates. Secondary faulting, controlled by a Coulomb-Anderson failure mechanism or by slip on preexisting faults can account for the occurrence of earthquakes on faults of other orientations.

Landslides and megathrust splay faults captured by the late Holocene sediment record of eastern Prince William Sound, Alaska

USGS Publications Warehouse

Finn, S.P.; Liberty, Lee M.; Haeussler, Peter J.; Pratt, Thomas L.

2015-01-01

We present new marine seismic‐reflection profiles and bathymetric maps to characterize Holocene depositional patterns, submarine landslides, and active faults beneath eastern and central Prince William Sound (PWS), Alaska, which is the eastern rupture patch of the 1964 Mw 9.2 earthquake. We show evidence that submarine landslides, many of which are likely earthquake triggered, repeatedly released along the southern margin of Orca Bay in eastern PWS. We document motion on reverse faults during the 1964 Great Alaska earthquake and estimate late Holocene slip rates for these growth faults, which splay from the subduction zone megathrust. Regional bathymetric lineations help define the faults that extend 40–70 km in length, some of which show slip rates as great as 3.75  mm/yr. We infer that faults mapped below eastern PWS connect to faults mapped beneath central PWS and possibly onto the Alaska mainland via an en echelon style of faulting. Moderate (Mw>4) upper‐plate earthquakes since 1964 give rise to the possibility that these faults may rupture independently to potentially generate Mw 7–8 earthquakes, and that these earthquakes could damage local infrastructure from ground shaking. Submarine landslides, regardless of the source of initiation, could generate local tsunamis to produce large run‐ups along nearby shorelines. In a more general sense, the PWS area shows that faults that splay from the underlying plate boundary present proximal, perhaps independent seismic sources within the accretionary prism, creating a broad zone of potential surface rupture that can extend inland 150 km or more from subduction zone trenches.

Flow paths in the Edwards aquifer, northern Medina and northeastern Uvalde counties, Texas, based on hydrologic identification and geochemical characterization and simulation

USGS Publications Warehouse

Clark, Allan K.; Journey, Celeste A.

2006-01-01

The U.S. Geological Survey, in cooperation with the San Antonio Water System, conducted a 4-year study during 2001– 04 to identify major ground-water flow paths in the Edwards aquifer in northern Medina and northeastern Uvalde Counties, Texas. The study involved use of geologic structure, surfacewater and ground-water data, and geochemistry to identify ground-water flow paths. Relay ramps and associated faulting in northern Medina County appear to channel ground-water flow along four distinct flow paths that move water toward the southwest. The northwestern Medina flow path is bounded on the north by the Woodard Cave fault and on the south by the Parkers Creek fault. Water moves downdip toward the southwest until the flow encounters a cross fault along Seco Creek. This barrier to flow might force part or most of the flow to the south. Departure hydrographs for two wells and discharge departure for a streamflow-gaging station provide evidence for flow in the northwestern Medina flow path. The north-central Medina flow path (northern part) is bounded by the Parkers Creek fault on the north and the Medina Lake fault on the south. The adjacent north-central Medina flow path (southern part) is bounded on the north by the Medina Lake fault and on the south by the Diversion Lake fault. The north-central Medina flow path is separated into a northern and southern part because of water-level differences. Ground water in both parts of the northcentral Medina flow path moves downgradient (and down relay ramp) from eastern Medina County toward the southwest. The north-central Medina flow path is hypothesized to turn south in the vicinity of Seco Creek as it begins to be influenced by structural features. Departure hydrographs for four wells and Medina Lake and discharge departure for a streamflow-gaging station provide evidence for flow in the north-central Medina flow path. The south-central Medina flow path is bounded on the north by the Seco Creek and Diversion Lake faults and on the south by the Haby Crossing fault. Because of bounding faults oriented northeast-southwest and adjacent flow paths directed south by other geologic structures, the south-central Medina flow path follows the configuration of the adjacent flow paths—oriented initially southwest and then south. Immediately after turning south, the south-central Medina flow path turns sharply east. Departure hydrographs for four wells and discharge departure for a streamflow-gaging station provide evidence for flow in the south-central Medina flow path. Statistical correlations between water-level departures for 11 continuously monitored wells provide additional evidence for the hypothesized flow paths. Of the 55 combinations of departure dataset pairs, the stronger correlations (those greater than .6) are all among wells in the same flow path, with one exception. Simulations of compositional differences in water chemistry along a hypothesized flow path in the Edwards aquifer and between ground-water and surface-water systems near Medina Lake were developed using the geochemical model PHREEQC. Ground-water chemistry for samples from five wells in the Edwards aquifer in the northwestern Medina flow path were used to evaluate the evolution of ground-water chemistry in the northwestern Medina flow path. Seven simulations were done for samples from pairs of these wells collected during 2001–03; three of the seven yielded plausible models. Ground-water samples from 13 wells were used to evaluate the evolution of ground-water chemistry in the north-central Medina flow path (northern and southern parts). Five of the wells in the most upgradient part of the flow path were completed in the Trinity aquifer; the remaining eight were completed in the Edwards aquifer. Nineteen simulations were done for samples from well pairs collected during 1995–2003; eight of the 19 yielded plausible models. Ground-water samples from seven wells were used to evaluate the evolution of ground-water chemistry in the south-central Medina flow path. One well was the Trinity aquifer end-member well upgradient from all flow paths, and another was a Trinity aquifer well in the most upgradient part of the flow path; all other wells were completed in the Edwards aquifer. Nine simulations were done for samples from well pairs collected during 1996–2003; seven of the nine yielded plausible models. The plausible models demonstrate that the four hypothesized flow paths can be partially supported geochemically. 

Exhumation history of the western Kyrgyz Tien Shan: Implications for intramontane basin formation

NASA Astrophysics Data System (ADS)

Bande, Alejandro; Sobel, Edward R.; Mikolaichuk, Alexander; Schmidt, Alexander; Stockli, Daniel F.

2017-01-01

The dextral Talas-Fergana Fault separates the western from the central Tien Shan. Recent work has shed light on the Cenozoic evolution of the eastern and central Tien Shan; much less attention has been paid to the western Tien Shan. In this contribution we present new thermochronological ages for the Fergana and Alai ranges that, combined with the available data set, constrain the Cenozoic exhumation history of the western Tien Shan. Following a tectonically quiet early Cenozoic period, we suggest an onset of exhumation at 25 Ma. This early onset was followed by a period of slower exhumation and in some areas minor reheating. A final, strong late Miocene rapid cooling event is well represented in the western Tien Shan as in other sectors of the range. The early onset of uplift of the western Tien Shan dissected the previously continuous westernmost Parathethyan Sea, progressively isolating basins (e.g., Fergana, Tarim, and Alai basins) in the central Asian hinterland. Moreover, the coeval timing of late Miocene uplift along the length of entire Tien Shan implies that neither the Pamir nor Tarim can be the sole driver for exhumation of the entire range.

Geomorphic features of surface ruptures associated with the 2016 Kumamoto earthquake in and around the downtown of Kumamoto City, and implications on triggered slip along active faults

NASA Astrophysics Data System (ADS)

Goto, Hideaki; Tsutsumi, Hiroyuki; Toda, Shinji; Kumahara, Yasuhiro

2017-02-01

The 30-km-long surface ruptures associated with the M w 7.0 ( M j 7.3) earthquake at 01:25 JST on April 16 in Kumamoto Prefecture appeared along the previously mapped 100-km-long active fault called the Futagawa-Hinagu fault zone (FHFZ). The surface ruptures appeared to have extended further west out of the main FHFZ into the Kumamoto Plain. Although InSAR analysis by Geospatial Information Authority of Japan (GSI) indicated coseismic surface deformation in and around the downtown of Kumamoto City, the surface ruptures have not been clearly mapped in the central part of the Kumamoto Plain, and whether there are other active faults other than the Futagawa fault in the Kumamoto Plain remained unclear. We produced topographical stereo images (anaglyph) from 5-m-mesh digital elevation model of GSI, which was generated from light detection and ranging data. We interpreted them and identified that several SW-sloping river terraces formed after the deposition of the pyroclastic flow deposits related to the latest large eruption of the Aso caldera (86.8-87.3 ka) are cut and deformed by several NW-trending flexure scarps down to the southwest. These 5.4-km-long scarps that cut across downtown Kumamoto were identified for the first time, and we name them as the Suizenji fault zone. Surface deformation such as continuous cracks, tilts, and monoclinal folding associated with the main shock of the 2016 Kumamoto earthquake was observed in the field along the fault zone. The amount of vertical deformation ( 0.1 m) along this fault associated with the 2016 Kumamoto earthquake was quite small compared to the empirically calculated coseismic slip (0.5 m) based on the fault length. We thus suggest that the slip on this fault zone was triggered by the Kumamoto earthquake, but the fault zone has potential to generate an earthquake with larger slip that poses a high seismic risk in downtown Kumamoto area.[Figure not available: see fulltext.

Geologic and Fossil Locality Maps of the West-Central Part of the Howard Pass Quadrangle and Part of the Adjacent Misheguk Mountain Quadrangle, Western Brooks Range, Alaska

USGS Publications Warehouse

Dover, James H.; Tailleur, Irvin L.; Dumoulin, Julie A.

2004-01-01

The map depicts the field distribution and contact relations between stratigraphic units, the tectonic relations between major stratigraphic sequences, and the detailed internal structure of these sequences. The stratigraphic sequences formed in a variety of continental margin depositional environments, and subsequently underwent a complexde formational history of imbricate thrust faulting and folding. A compilation of micro and macro fossil identifications is included in this data set.

Automated Power Systems Management (APSM)

NASA Technical Reports Server (NTRS)

Bridgeforth, A. O.

1981-01-01

A breadboard power system incorporating autonomous functions of monitoring, fault detection and recovery, command and control was developed, tested and evaluated to demonstrate technology feasibility. Autonomous functions including switching of redundant power processing elements, individual load fault removal, and battery charge/discharge control were implemented by means of a distributed microcomputer system within the power subsystem. Three local microcomputers provide the monitoring, control and command function interfaces between the central power subsystem microcomputer and the power sources, power processing and power distribution elements. The central microcomputer is the interface between the local microcomputers and the spacecraft central computer or ground test equipment.

Slip along the Sultanhanı Fault in Central Anatolia from deformed Pleistocene shorelines of palaeo-lake Konya and implications for seismic hazards in low-strain regions

NASA Astrophysics Data System (ADS)

Melnick, Daniel; Yıldırım, Cengiz; Hillemann, Christian; Garcin, Yannick; Çiner, Attila; Pérez-Gussinyé, Marta; Strecker, Manfred R.

2017-06-01

Central Anatolia is a low-relief, high-elevation region where decadal-scale deformation rates estimated from space geodesy suggest low strain rates within a stiff microplate. However, numerous Quaternary faults have been mapped within this low-strain region and estimating their slip rate and seismic potential is important for hazard assessments in an area of increasing infrastructural development. Here we focus on the Sultanhanı Fault (SF), which constitutes an integral part of the Eskişehir-Cihanbeyli Fault System, and use deformed maximum highstand shorelines of palaeo-lake Konya to estimate tectonic slip rates at millennial scale. Some of these shorelines were previously interpreted as fault scarps, but we provide conclusive evidence for their erosional origin. We found that shoreline-angle elevations estimated from differential GPS profiles record vertical displacements of 10.2 m across the SF. New radiocarbon ages of lacustrine molluscs suggest 22.4 m of relative lake-level fall between 22.1 ± 0.3 and 21.7 ± 0.4 cal. ka BP, constraining the timing of abrupt abandonment of the highstand shoreline. Models of lithospheric rebound associated with regressions of the Tuz Gölü and Konya palaeo-lakes predict only ∼1 m of regional-scale uplift across the Konya Basin. Dislocation models of displaced shorelines suggest fault-slip rates of 1.5 and 1.8 mm yr-1 for planar and listric fault geometries, respectively, providing reasonable results for the latter. We found fault scarps in the Nasuhpınar mudflat that likely represent the most recent ground-breaking rupture of the SF, with an average vertical displacement of 1.2 ± 0.5 m estimated from 54 topographic profiles, equivalent to a M ∼ 6.5-6.9 earthquake based on empirical scaling laws. If such events were characteristic during the ultimate 21 ka, a relatively short recurrence time of ∼800-900 yr would be needed to account for the millennial slip rate. Alternatively, the fault scarp at Nasuhpınar might represent a larger earthquake requiring more frequent smaller events to account for the millennial rate. The relatively fast slip rate of the SF over the past 21 ka is unlikely to have persisted over longer timescales and might reflect spatiotemporal variations in deformation rates within kinematically-linked fault systems within Central Anatolia, or a transient perturbation to the local stress field or fault strength. Such perturbation might have been related to climatically controlled changes in surface and near-surface loads and by interactions among the different tectonic processes that have been proposed to drive the overall slow uplift and associated extension in the Central Anatolian Plateau.

First-order and subsidiary faults controlling the time-space evolution of the Central Italy 2016 seismic sequence - a multi-source data detailed 3D reconstruction

NASA Astrophysics Data System (ADS)

Lavecchia, Giusy; de nardis, Rita; Ferrarini, Federica; Cirillo, Daniele; Brozzetti, Francesco

2017-04-01

The Central Italy 2016 seismic sequence, with its three major events (24 August, Mw 6.0/6.2; 26 October Mw5.9/6.0; 30 October Mw6.5/6.6), activated a well-known active west-dipping extensional fault alignment of central Italy (Vettore-Gorzano faults, VEGO). Soon after the first event, based on geological, interferometric and at that moment available seismological data, a preliminary 3D fault model of VEGO was built. Such a model is here updated and improved at the light of a large amount of relocated earthquake data (time interval 24 August to 30 November 2016, 0.1≤ML ≤6.5, Chiaraluce at al., submitted to SRL) plus additional geological information. The 3D modeling was done using the software package MOVE from the Midland Valley. All the available data were taken into consideration (surface traces, fault-slip data, primary co-seismic surface fractures, geological maps and cross-sections, hypocentral locations and focal mechanisms of both background seismicity and seismic sequences). The VEGO geometric configuration did not substantially changed with respect to the previous model, but some additional structures involved in the sequence were reconstructed. In particular, four additional faults are well evident: a NE-dipping normal fault (dip-angle 50˚ ) antithetic to Vettore Fault, located at depths between 1 and 5 km; a WNW dipping plane (dip-angle 30˚ ) located at depth between 1 and 4 km within the Vettore footwall volume; this structure represents a splay of the late Miocene Sibillini thrust, which is evidently cross-cut and dislocated by the Vettore normal fault; a SW-dipping normal fault representing an unknown northward prosecution of the VEGO alignment, where since 26 October a relevant seismic activity was released; an unknown east-dipping low-angle detachment, where VEGO detaches at a depth of about 10-11 km. An uninterrupted microseismic activity has illuminated such a detachment not only during the overall sequence, but also in the previous months. At the light of the reconstructed geometric pattern integrated with the evidences of primary co-seismic fractures, it results evident that the Central Italy seismic sequence represents a "classic", although complex, intra-Apennine normal-faulting event, reactivating a long-term quiescent seismogenic alignment (e.g. VEGO). The reactivated and inverted compressional structures are confined at shallow depth within the Vettore footwall, and in no way control the major events of the sequence. Conversely, an important regional role is played by the east-dipping detachment. It represents the missing geometric link between the Altotiberina LANF of northern Umbria and the recently discovered LANF of Latium-Abruzzi.

A Seismic Source Model for Central Europe and Italy

NASA Astrophysics Data System (ADS)

Nyst, M.; Williams, C.; Onur, T.

2006-12-01

We present a seismic source model for Central Europe (Belgium, Germany, Switzerland, and Austria) and Italy, as part of an overall seismic risk and loss modeling project for this region. A separate presentation at this conference discusses the probabilistic seismic hazard and risk assessment (Williams et al., 2006). Where available we adopt regional consensus models and adjusts these to fit our format, otherwise we develop our own model. Our seismic source model covers the whole region under consideration and consists of the following components: 1. A subduction zone environment in Calabria, SE Italy, with interface events between the Eurasian and African plates and intraslab events within the subducting slab. The subduction zone interface is parameterized as a set of dipping area sources that follow the geometry of the surface of the subducting plate, whereas intraslab events are modeled as plane sources at depth; 2. The main normal faults in the upper crust along the Apennines mountain range, in Calabria and Central Italy. Dipping faults and (sub-) vertical faults are parameterized as dipping plane and line sources, respectively; 3. The Upper and Lower Rhine Graben regime that runs from northern Italy into eastern Belgium, parameterized as a combination of dipping plane and line sources, and finally 4. Background seismicity, parameterized as area sources. The fault model is based on slip rates using characteristic recurrence. The modeling of background and subduction zone seismicity is based on a compilation of several national and regional historic seismic catalogs using a Gutenberg-Richter recurrence model. Merging the catalogs encompasses the deletion of double, fake and very old events and the application of a declustering algorithm (Reasenberg, 2000). The resulting catalog contains a little over 6000 events, has an average b-value of -0.9, is complete for moment magnitudes 4.5 and larger, and is used to compute a gridded a-value model (smoothed historical seismicity) for the region. The logic tree weighs various completeness intervals and minimum magnitudes. Using a weighted scheme of European and global ground motion models together with a detailed site classification map for Europe based on Eurocode 8, we generate hazard maps for recurrence periods of 200, 475, 1000 and 2500 yrs.

Geochemistry, mineralization, structure, and permeability of a normal-fault zone, Casino mine, Alligator Ridge district, north central Nevada

NASA Astrophysics Data System (ADS)

Hammond, K. Jill; Evans, James P.

2003-05-01

We examine the geochemical signature and structure of the Keno fault zone to test its impact on the flow of ore-mineralizing fluids, and use the mined exposures to evaluate structures and processes associated with normal fault development. The fault is a moderately dipping normal-fault zone in siltstone and silty limestone with 55-100 m of dip-slip displacement in north-central Nevada. Across-strike exposures up to 180 m long, 65 m of down-dip exposure and 350 m of along-strike exposure allow us to determine how faults, fractures, and fluids interact within mixed-lithology carbonate-dominated sedimentary rocks. The fault changes character along strike from a single clay-rich slip plane 10-20 mm thick at the northern exposure to numerous hydrocarbon-bearing, calcite-filled, nearly vertical slip planes in a zone 15 m wide at the southern exposure. The hanging wall and footwall are intensely fractured but fracture densities do not vary markedly with distance from the fault. Fault slip varies from pure dip-slip to nearly pure strike-slip, which suggests that either slip orientations may vary on faults in single slip events, or stress variations over the history of the fault caused slip vector variations. Whole-rock major, minor, and trace element analyses indicate that Au, Sb, and As are in general associated with the fault zone, suggesting that Au- and silica-bearing fluids migrated along the fault to replace carbonate in the footwall and adjacent hanging wall rocks. Subsequent fault slip was associated with barite and calcite and hydrocarbon-bearing fluids deposited at the southern end of the fault. No correlation exists at the meter or tens of meter scale between mineralization patterns and fracture density. We suggest that the fault was a combined conduit-barrier system in which the fault provides a critical connection between the fluid sources and fractures that formed before and during faulting. During the waning stages of deposit formation, the fault behaved as a localized conduit to hydrocarbon-bearing calcite veins. The results of this study show that fault-zone character may change dramatically over short, deposit- or reservoir-scale distances. The presence of damage zones may not be well correlated at the fine scale with geochemically defined regions of the fault, even though a gross spatial correlation may exist.

Structure of pseudotachylyte vein systems as a key to co-seismic rupture dynamics: the case of Gavilgarh-Tan Shear Zone, central India

NASA Astrophysics Data System (ADS)

Chattopadhyay, A.; Bhattacharjee, D.; Mukherjee, S.

2014-04-01

The secondary fractures associated with a major pseudotachylyte-bearing fault vein in the sheared aplitic granitoid of the Proterozoic Gavilgarh-Tan Shear Zone in central India are mapped at the outcrop scale. The fracture maps help to identify at least three different types of co-seismic ruptures, e.g., X-X', T1 and T2, which characterize sinistral-sense shearing of rocks, confined between two sinistral strike-slip faults slipping at seismic rate. From the asymmetric distribution of tensile fractures around the sinistral-sense fault vein, the direction of seismic rupture propagation is predicted to have occurred from west-southwest to east-northeast, during an ancient (Ordovician?) earthquake. Calculations of approximate co-seismic displacement on the faults and seismic moment ( M 0) of the earthquake are attempted, following the methods proposed by earlier workers. These estimates broadly agree to the findings from other studied fault zones (e.g., Gole Larghe Fault zone, Italian Alps). This study supports the proposition by some researchers that important seismological information can be extracted from tectonic pseudotachylytes of all ages, provided they are not reworked by subsequent tectonic activity.

Earthquake Clustering on Normal Faults: Insight from Rate-and-State Friction Models

NASA Astrophysics Data System (ADS)

Biemiller, J.; Lavier, L. L.; Wallace, L.

2016-12-01

Temporal variations in slip rate on normal faults have been recognized in Hawaii and the Basin and Range. The recurrence intervals of these slip transients range from 2 years on the flanks of Kilauea, Hawaii to 10 kyr timescale earthquake clustering on the Wasatch Fault in the eastern Basin and Range. In addition to these longer recurrence transients in the Basin and Range, recent GPS results there also suggest elevated deformation rate events with recurrence intervals of 2-4 years. These observations suggest that some active normal fault systems are dominated by slip behaviors that fall between the end-members of steady aseismic creep and periodic, purely elastic, seismic-cycle deformation. Recent studies propose that 200 year to 50 kyr timescale supercycles may control the magnitude, timing, and frequency of seismic-cycle earthquakes in subduction zones, where aseismic slip transients are known to play an important role in total deformation. Seismic cycle deformation of normal faults may be similarly influenced by its timing within long-period supercycles. We present numerical models (based on rate-and-state friction) of normal faults such as the Wasatch Fault showing that realistic rate-and-state parameter distributions along an extensional fault zone can give rise to earthquake clusters separated by 500 yr - 5 kyr periods of aseismic slip transients on some portions of the fault. The recurrence intervals of events within each earthquake cluster range from 200 to 400 years. Our results support the importance of stress and strain history as controls on a normal fault's present and future slip behavior and on the characteristics of its current seismic cycle. These models suggest that long- to medium-term fault slip history may influence the temporal distribution, recurrence interval, and earthquake magnitudes for a given normal fault segment.

Structural characteristics and implication on tectonic evolution of the Daerbute strike-slip fault in West Junggar area, NW China

NASA Astrophysics Data System (ADS)

Wu, Kongyou; Pei, Yangwen; Li, Tianran; Wang, Xulong; Liu, Yin; Liu, Bo; Ma, Chao; Hong, Mei

2018-03-01

The Daerbute fault zone, located in the northwestern margin of the Junggar basin, in the Central Asian Orogenic Belt, is a regional strike-slip fault with a length of 400 km. The NE-SW trending Daerbute fault zone presents a distinct linear trend in plain view, cutting through both the Zair Mountain and the Hala'alate Mountain. Because of the intense contraction and shearing, the rocks within the fault zone experienced high degree of cataclasis, schistosity, and mylonization, resulting in rocks that are easily eroded to form a valley with a width of 300-500 m and a depth of 50-100 m after weathering and erosion. The well-exposed outcrops along the Daerbute fault zone present sub-horizontal striations and sub-vertical fault steps, indicating sub-horizontal shearing along the observed fault planes. Flower structures and horizontal drag folds are also observed in both the well-exposed outcrops and high-resolution satellite images. The distribution of accommodating strike-slip splay faults, e.g., the 973-pluton fault and the Great Jurassic Trough fault, are in accordance with the Riedel model of simple shear. The seismic and time-frequency electromagnetic (TFEM) sections also demonstrate the typical strike-slip characteristics of the Daerbute fault zone. Based on detailed field observations of well-exposed outcrops and seismic sections, the Daerbute fault can be subdivided into two segments: the western segment presents multiple fault cores and damage zones, whereas the eastern segment only presents a single fault core, in which the rocks experienced a higher degree of rock cataclasis, schistosity, and mylonization. In the central overlapping portion between the two segments, the sediments within the fault zone are primarily reddish sandstones, conglomerates, and some mudstones, of which the palynological tests suggest middle Permian as the timing of deposition. The deformation timing of the Daerbute fault was estimated by integrating the depocenters' basinward migration and initiation of the splay faults (e.g., the Great Jurassic Trough fault and the 973-pluton fault). These results indicate that there were probably two periods of faulting deformation for the Daerbute fault. By integrating our study with previous studies, we speculate that the Daerbute fault experienced a two-phase strike-slip faulting deformation, commencing with the initial dextral strike-slip faulting in mid-late Permian, and then being inversed to sinistral strike-slip faulting since the Triassic. The results of this study can provide useful insights for the regional tectonics and local hydrocarbon exploration.

California State Waters Map Series: offshore of San Gregorio, California

USGS Publications Warehouse

Cochrane, Guy R.; Dartnell, Peter; Greene, H. Gary; Watt, Janet T.; Golden, Nadine E.; Endris, Charles A.; Phillips, Eleyne L.; Hartwell, Stephen R.; Johnson, Samuel Y.; Kvitek, Rikk G.; Erdey, Mercedes D.; Bretz, Carrie K.; Manson, Michael W.; Sliter, Ray W.; Ross, Stephanie L.; Dieter, Bryan E.; Chin, John L.; Cochran, Susan A.; Cochrane, Guy R.; Cochran, Susan A.

2014-01-01

In 2007, the California Ocean Protection Council initiated the California Seafloor Mapping Program (CSMP), designed to create a comprehensive seafloor map of high-resolution bathymetry, marine benthic habitats, and geology within the 3-nautical-mile limit of California's State Waters. The CSMP approach is to create highly detailed seafloor maps through collection, integration, interpretation, and visualization of swath sonar data, acoustic backscatter, seafloor video, seafloor photography, high-resolution seismic-reflection profiles, and bottom-sediment sampling data. The map products display seafloor morphology and character, identify potential marine benthic habitats, and illustrate both the surficial seafloor geology and shallow (to about 100 m) subsurface geology. The Offshore of San Gregorio map area is located in northern California, on the Pacific coast of the San Francisco Peninsula about 50 kilometers south of the Golden Gate. The map area lies offshore of the Santa Cruz Mountains, part of the northwest-trending Coast Ranges that run roughly parallel to the San Andreas Fault Zone. The Santa Cruz Mountains lie between the San Andreas Fault Zone and the San Gregorio Fault system. The nearest significant onshore cultural centers in the map area are San Gregorio and Pescadero, both unincorporated communities with populations well under 1,000. Both communities are situated inland of state beaches that share their names. No harbor facilities are within the Offshore of San Gregorio map area. The hilly coastal area is virtually undeveloped grazing land for sheep and cattle. The coastal geomorphology is controlled by late Pleistocene and Holocene slip in the San Gregorio Fault system. A westward bend in the San Andreas Fault Zone, southeast of the map area, coupled with right-lateral movement along the San Gregorio Fault system have caused regional folding and uplift. The coastal area consists of high coastal bluffs and vertical sea cliffs. Coastal promontories in the northern and southern parts of the map area are the result of right-lateral motion on strands of the San Gregorio Fault system. In the south, headlands near Pescadero Point have been uplifted by motion along the west strand of the San Gregorio Fault (also called the Frijoles Fault), which separates rocks of the Pigeon Point Formation south of the fault from rocks of the Purisima Formation north of the fault. The regional uplift in this map area has caused relatively shallow water depths within California's State Waters and, thus, little accommodation space for sediment accumulation. Sediment is observed offshore in the central part of the map area, in the shelter of the headlands north of the east strand of the San Gregorio Fault (also called the Coastways Fault) around Miramontes Point (about 5 km north of the map area) and also on the outer half of the California's State Waters shelf in the south where depths exceed 40 m. Sediment in the outer shelf of California's State Waters is rippled, indicating some mobility. The Offshore of San Gregorio map area lies within the cold-temperate biogeographic zone that is called either the "Oregonian province" or the "northern California ecoregion." This biogeographic province is maintained by the long-term stability of the southward-flowing California Current, an eastern limb of the North Pacific subtropical gyre that flows from Oregon to Baja California. At its midpoint off central California, the California Current transports subarctic surface (0–500 m deep) waters southward, about 150 to 1,300 km from shore. Seasonal northwesterly winds that are, in part, responsible for the California Current, generate coastal upwelling. The south end of the Oregonian province is at Point Conception (about 350 km south of the map area), although its associated phylogeographic group of marine fauna may extend beyond to the area offshore of Los Angeles in southern California. The ocean off of central California has experienced a warming over the last 50 years that is driving an ecosystem shift away from the productive subarctic regime towards a depopulated subtropical environment. Seafloor habitats in the Offshore of San Gregorio map area, which lies within the Shelf (continental shelf) megahabitat, range from significant rocky outcrops that support kelp-forest communities nearshore to rocky-reef communities in deep water. Biological productivity resulting from coastal upwelling supports diverse populations of sea birds such as Sooty Shearwater, Western Gull, Common Murre, Cassin's Auklet, and many other less populous bird species. In addition, an observable recovery of Humpback and Blue Whales has occurred in the area; both species are dependent on coastal upwelling to provide nutrients. The large extent of exposed inner shelf bedrock supports large forests of "bull kelp," which is well adapted for high wave-energy environments. Common fish species found in the kelp beds and rocky reefs include lingcod and various species of rockfish and greenling.

Paleomagnetism and magnetic fabric of the Eastern Cordillera of Colombia: Evidence for oblique convergence and non-rotational reactivation of a Mesozoic intra-continental rift

NASA Astrophysics Data System (ADS)

Jiménez Díaz, G.; Speranza, F.; Faccenna, C.; Bayona, G.; Mora, A.

2012-12-01

The Eastern Cordillera of Colombia (EC) is a double-verging mountain system inverting a Mesozoic rift, and bounded by major reverse faults that locally involve crystalline and metamorphic Precambrian-Lower Paleozoic basement rocks, as well as Upper Paleozoic-Cenozoic sedimentary and volcanic sequences. In map view the EC is a curved mountain belt with a regional structural strike that ranges from NNE in the southern part to NNW in the northern part. The origin of its curvature has not been studied or discussed so far. We report on an extensive paleomagnetic and anisotropy of magnetic susceptibility (AMS) investigation of the EC, in order to address to test its non-rotational vs. oroclinal nature. Fifty-eight sites were gathered from Cretaceous to Miocene marine and continental strata, both from the southern and northern parts of the EC; additionally, we examined the southern Maracaibo plate, at the junction between the Santander Massif and the Merida Andes of Colombia (Cucuta zone). Twenty-three sites reveal no rotation of the EC range with respect to stable South America. In contrast, a 35°±9° clockwise rotation is documented in four post-Miocene magnetically overprinted sites from the Cucuta zone. Magnetic lineations from AMS analysis do not trend parallel to the chain, but are oblique to the main strike of the orogenic belt. By also considering GPS evidence of a ~1 cm/yr ENE displacement of central-western Colombia accommodated by the EC, we suggest that the late Miocene-recent deformation occurred by a ENE oblique convergence reactivating a NNE rift zone. Our data show that the EC is a non-rotational chain, and that the locations of the Mesozoic rift and the mountain chain roughly correspond. One possible solution is that the oblique shortening is partitioned in pure dip-slip shear characterizing thick-skinned frontal thrust sheets (well-known along both chain fronts), and by range-parallel right-lateral strike-slip fault(s), which have not been identified yet and likely occur in the axial part of the EC. The clockwise rotation in the Cucuta zone reflects late Cenozoic and ongoing right-lateral strike-slip displacement occurring along buried faults parallel to the Boconó fault system, possibly connected with the right-lateral faults inferred along the axial part of the EC.

Impact from Magnitude-Rupture Length Uncertainty on Seismic Hazard and Risk

NASA Astrophysics Data System (ADS)

Apel, E. V.; Nyst, M.; Kane, D. L.

2015-12-01

In probabilistic seismic hazard and risk assessments seismic sources are typically divided into two groups: fault sources (to model known faults) and background sources (to model unknown faults). In areas like the Central and Eastern United States and Hawaii the hazard and risk is driven primarily by background sources. Background sources can be modeled as areas, points or pseudo-faults. When background sources are modeled as pseudo-faults, magnitude-length or magnitude-area scaling relationships are required to construct these pseudo-faults. However the uncertainty associated with these relationships is often ignored or discarded in hazard and risk models, particularly when faults sources are the dominant contributor. Conversely, in areas modeled only with background sources these uncertainties are much more significant. In this study we test the impact of using various relationships and the resulting epistemic uncertainties on the seismic hazard and risk in the Central and Eastern United States and Hawaii. It is common to use only one magnitude length relationship when calculating hazard. However, Stirling et al. (2013) showed that for a given suite of magnitude-rupture length relationships the variability can be quite large. The 2014 US National Seismic Hazard Maps (Petersen et al., 2014) used one magnitude-rupture length relationship (Somerville, et al., 2001) in the Central and Eastern United States, and did not consider variability in the seismogenic rupture plane width. Here we use a suite of metrics to compare the USGS approach with these variable uncertainty models to assess 1) the impact on hazard and risk and 2) the epistemic uncertainty associated with choice of relationship. In areas where the seismic hazard is dominated by larger crustal faults (e.g. New Madrid) the choice of magnitude-rupture length relationship has little impact on the hazard or risk. However away from these regions, the choice of relationship is more significant and may approach the size of the uncertainty associated with the ground motion prediction equation suite.

Seismic Supercycles of Normal Faults in Central Italy over Various Time Scales Revealed by 36Cl Cosmogenic Dating

NASA Astrophysics Data System (ADS)

Benedetti, L. C.; Tesson, J.; Perouse, E.; Puliti, I.; Fleury, J.; Rizza, M.; Billant, J.; Pace, B.

2017-12-01

The use of 36Cl cosmogenic nuclide as a paleoseismological tool for normal faults in the Mediterranean has revolutionized our understanding of their seismic cycle (Gran Mitchell et al. 2001, Benedetti et al. 2002). Here we synthetized results obtained on 13 faults in Central Italy. Those records cover a period of 8 to 45 ka. The mean recurrence time of retrieved seismic events is 5.5 ±6 ka, with a mean slip per event of 2.5 ± 1.8 m and a mean slip-rate from 0.1 to 2.4 mm/yr. Most retrieved events correspond to single events according to scaling relationships. This is also supported by the 2 m-high co-seismic slip observed on the Mt Vettore fault after the October 30, 2016 M6.5 earthquake in Central Italy (EMERGEO working group). Our results suggest that all faults have experienced one or several periods of slip acceleration with bursts of seismic activity, associated with very high slip-rate of 1.7-9 mm/yr, corresponding to 2-20 times their long-term slip-rate. The duration of those bursts is variable from a fault to another (from < 2 kyr to 4-10 kyr). Those periods of acceleration are generally separated by longer periods of quiescence with no or very few events. Those alternating periods correspond to a long-term variation of the strain level with all faults oscillating between strain maximum and minimum, the length of strain loading and release being significantly different from one fault to another, those supercycles occurring over periods of 8 to 45 ka. We found relationships between the mean slip-rate, the mean slip per event and the mean recurrence time. This might suggest that the seismic activity of those faults could be controlled by their intrinsic properties (e.g. long-term slip-rate, fault-length, state of structural maturity). Our results also show events clustering with several faults rupturing in less than 500 yrs on adjacent or distant faults within the studied area. The Norcia-Amatrice seismic sequence, ≈ 50 km north of our study area, also evidenced this clustering behaviour, with over the last 20 yrs several successive events of Mw 5 to 6.5 (from north to south: Colfiorito 1997 Mw6.0, Norcia 2016 Mw6.5, L'Aquila 2009 Mw6.3), rupturing various fault systems, over a total length of ≈100 km. This sequence will allow to better understand earthquake kinematics and spatiotemporal slip distribution during those seismic bursts.

Identifying the source of fluvial terrace deposits using XRF scanning and Canonical Discriminant Analysis: A case study of the Chihshang terraces, eastern Taiwan

NASA Astrophysics Data System (ADS)

Chang, Queenie; Lee, Jian-Cheng; Hunag, Jyh-Jaan; Wei, Kuo-Yen; Chen, Yue-Gau; Byrne, Timothy B.

2018-05-01

The source of fluvial deposits in terraces provides important information about the catchment fluvial processes and landform evolution. In this study, we propose a novel approach that combines high-resolution Itrax-XRF scanning and Canonical Discriminant Analysis (CDA) to identify the source of fine-grained fluvial terrace deposits. We apply this approach to a group of terraces that are located on the hanging wall of the Chihshang Fault in eastern Taiwan with two possible sources, the Coastal Range on the east and the Central Range on the west. Our results of standard samples from the two potential sources show distinct ranges of canonical variables, which provided a better separation ability than individual chemical elements. We then tested the possibility of using this approach by applying it to several samples with known sediment sources and obtain positive results. Applying this same approach to the fine-grained sediments in Chihshang terraces indicates that they are mostly composed of Coastal Range material but also contain some inputs from the Central Range. In two lowest terraces T1 and T2, the fine-grained deposits show significant Central Range component. For terrace T4, the results show less Central Range input and a trend of decreasing Central Range influences up section. The Coastal Range material becomes dominant in the two highest terraces T7 and T10. Sediments in terrace T5 appear to have been potentially altered by post-deposition chemical alteration processes and are not included in the analysis. Our results show that the change in source material in the terraces deposits was relatively gradual rather than the sharp changes suggested by the composition of the gravels and conglomerates. We suggest that this change in sources is related to the change in dominant fluvial processes that controlled by the tectonic activity.

Current crustal deformation of the Taiwan orogen reassessed by cGPS strain-rate estimation and focal mechanism stress inversion

NASA Astrophysics Data System (ADS)

Chen, Sean Kuanhsiang; Wu, Yih-Min; Hsu, Ya-Ju; Chan, Yu-Chang

2017-07-01

We study internal deformation of the Taiwan orogen, a young arc-continental collision belt, which the spatial heterogeneity remains unclear. We aim to ascertain heterogeneity of the orogenic crust in depth when specifying general mechanisms of the Taiwan orogeny. To reach this goal, we used updated data of continuous GPS (cGPS) and earthquake focal mechanisms to reassess geodetic strain-rate and seismic stress fields of Taiwan, respectively. We updated the both data sets from 1990 to 2015 to provide large amount of constraints on surficial and internal deformation of the crust for a better understanding. We estimated strain-rate tensors by calculating gradient tensors of cGPS station velocities in horizontal 0.1°-spacing grids via Delaunay triangulation. We determined stress tensors within a given horizontal and vertical grid cell of 0.1° and 10 km, respectively, by employing the spatial and temporal stress inversion. To minimize effects of the 1999 Mw 7.6 Chi-Chi earthquake on trends of the strain and stress, we modified observational possible bias of the cGPS velocities after the earthquake and removed the first 15-month focal mechanisms within the fault rupture zone. We also calculated the Anderson fault parameter (Aϕ) based on stress ratios and rake angles to quantitatively describe tectonic regimes of Taiwan. By examining directions of seismic compressive axes and styles of faulting, our results indicate that internal deformation of the crust is presently heterogeneous in the horizontal and vertical spaces. Directions of the compressive axes are fan-shaped oriented between N10°W and N110°W in the western and mid-eastern Taiwan at the depths of 0-20 km and near parallel to orientations of geodetic compressional axes. The orientations agreed with predominantly reverse faulting in the western Taiwan at the same depth range, implying a brittle deformation regime against the Peikang Basement High. Orientations of the compressive axes most rotated counter-clockwise at the depths of 20-40 km, coinciding with transition of styles of faulting from reverse to strike-slip faulting along the depths as revealed by variation of the Aϕ values. The features indicate that internal deformation of the upper crust is primarily driven by the same compressional mechanism. It implies that geodetic strains could detect the deformation from surface down to a maximal depth of 20 km in most regimes of Taiwan. We find that heterogeneity in orientations of compressive axes and styles of faulting is strong in two regimes at the northern and southern Central Range, coinciding to areas of the orogenic thinned/thickened crust. Conversely, the heterogeneity is weak in the central Western Foothills at surrounding area of root of the overthickened crust. This observation, coupled with regional seismological observations, may imply that vertical deformation from crustal thickening and thinning and thinning-related dynamics from mantle flows may have joint influence on degree of stress heterogeneity.

Timing and Magnitude of Upper Crustal Shortening in the Gonghe Basin Region of the Northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Craddock, W. H.; Kirby, E.; Harkins, N.; Zhang, H.

2008-12-01

Characterizing the space-time patterns of the growth of high topography in Asia is an important step toward a deeper understanding of the mechanics of intracontinental deformation and its influence on global climate. In northeastern Tibet, there is emerging evidence that a number of ranges around the margins of the plateau experienced a pulse of deformation in the Late Miocene (ca. 12-8 Ma). It remains uncertain, however, whether this event was confined to the margins of the plateau, or whether interior regions deformed synchronously. Here we present a preliminary assessment of the timing and magnitude of upper crustal shortening along the margins of the Gonghe-Tongde basin complex. The Gonghe basin is located at the boundary between the high plateau of central Tibet and the southern flank of the Qilian Shan, and as such it is well-suited as a site to begin reconstructing patterns of plateau growth. The basin is overthrust by two regionally-extensive fault systems, the Qinghai Nan Shan (QNS) fault system on the north side and the Gonghe Nan Shan (GNS) fault system on the south side. Both fault systems are associated with deformation of Tertiary strata; variations in dip, sedimentary facies, and provenance are used to interpret the onset of growth along the margins of the Gonghe basin. A combination of the architecture of pre- and syntectonic basin strata, field measurements of fault dip, fault plane solutions, and topographic analysis of fold backlimbs for the GNS and QNS leads us to infer that the fault systems are a) trishear fault propagation style thrust faults and b) south vergent, with ~30 degree fault ramps soleing into a gently dipping decollement. Reconstructions of fold evolution suggest that the area has experienced > 5 km of upper crustal shortening in the late Cenozoic. A combination of magnetostratigraphy, biostratigraphy and cosmogenic burial ages provides preliminary age control. South of the GNS, a 250 m thick package of growth related strata are found to be 3.4 - 0.5 Ma. A 500 m thick exposure of growth strata on the north side of the range is also interpreted to be Plio-Quaternary in age. At present, however, we can only place a minimum bound on the onset of deformation of ca. 4-5 Ma. In light of a companion study interpreting the onset of deformation along the QNS at >= 5-7 Ma (Zhang H., in review), deformation of the Gonghe region appears to be slightly more recent than at the plateau margins. Historic seismicity and deformation of late-Quaternary alluvial surfaces on both fault systems indicate that these structures have remained active into the Pleistocene.

Stratiform zinc-lead mineralization in Nasina assemblage rocks of the Yukon-Tanana Upland in east-central Alaska

USGS Publications Warehouse

Dusel-Bacon, Cynthia; Bressler, Jason R.; Takaoka, Hidetoshi; Mortensen, James K.; Oliver, Douglas H.; Leventhal, Joel S.; Newberry, Rainer J.; Bundtzen, Thomas K.

1998-01-01

The Yukon-Tanana Upland of east-central Alaska and Yukon comprises thrust sheets of ductilely deformed metasedimentary and metaigneous rocks of uncertain age and origin that are overlain by klippen of weakly metamorphosed oceanic rocks of the Seventymile-Slide Mountain terrane, and intruded by post-kinematic Early Jurassic, Cretaceous and Tertiary granitoids. Metamorphosed continental margin strata in the Yukon-Tanana Upland of east-central Alaska are thought to be correlative, on the basis of stratigraphic similarities and sparse Mississippian U-Pb zircon and fossil ages (Mortensen, 1992), with middle Paleozoic metasedimentary and metavolcanic rocks in the eastern Alaska Range and in western and southeastern Yukon. Furthermore, rocks in the northern Yukon-Tanana Upland may correlate across the Tintina fault with unmetamorphosed counterparts in the Selwyn Basin (Murphy and Abbott, 1995). Volcanic-hosted (VMS) and sedimentary exhalative (sedex) massive sulfide occurrences are widely reported for these other areas (green-colored unit of fig. 1) but, as yet, have not been documented in the Alaskan part of the Yukon-Tanana Upland. Recent discoveries of VMS deposits in Devono-Mississippian metavolcanic rocks in the Finlayson Lake area of southeastern Yukon (Hunt, 1997) have increased the potential for finding VMS deposits in rocks of similar lithology and age in the Yukon-Tanana Upland of Alaska. Restoration of 450 km of early Tertiary dextral movement along the Tintina fault juxtaposes these two areas.

Mechanisms and Magnitude of Cenozoic Crustal Extension in the Vicinity of Lake Mead, Nevada and the Beaver Dam Mountains, Utah: Geochemical, Geochronological,Thermochronological and Geophysical Constraints

NASA Astrophysics Data System (ADS)

Almeida, Rafael V.

The central Basin and Range Province of Nevada and Utah was one of the first areas in which the existence of widespread low-angle normal faults or detachments was first recognized. The magnitude of associated crustal extension is estimated by some to be large, in places increasing original line lengths by as much as a factor of four. However, rock mechanics experiments and seismological data cast doubt on whether these structures slipped at low inclination in the manner generally assumed. In this dissertation, I review the evidence for the presence of detachment faults in the Lake Mead and Beaver Dam Mountains areas and place constraints on the amount of extension that has occurred there since the Miocene. Chapter 1 deals with the source-provenance relationship between Miocene breccias cropping out close to Las Vegas, Nevada and their interpreted source at Gold Butte, currently located 65 km to the east. Geochemical, geochronological and thermochronological data provide support for that long-accepted correlation, though with unexpected mismatches requiring modification of the original hypothesis. In Chapter 2, the same data are used to propose a refinement of the timing of ~1.45 Ga anorogenic magmatism, and the distribution of Proterozoic crustal boundaries. Chapter 3 uses geophysical methods to address the subsurface geometry of faults along the west flank of the Beaver Dam Mountains of southwestern Utah. The data suggest that the range is bounded by steeply inclined normal faults rather than a regional-scale detachment fault. Footwall folding formerly ascribed to Miocene deformation is reinterpreted as an expression of Cretaceous crustal shortening. Fission track data presented in Chapter 4 are consistent with mid-Miocene exhumation adjacent to high-angle normal faults. They also reveal a protracted history dating back to the Pennsylvanian-Permian time, with implications for the interpretation of other basement-cored uplifts in the region. A key finding of this dissertation is that the magnitude of crustal extension in this region has been overestimated. The pre-extensional width was increased by a factor of two across Lake Mead, through a combination of high-angle normal faulting and strike-slip deformation. Data from the transect across the Beaver Dam Mountains suggest substantially less extension, with the difference accommodated for the most part by displacement on the intervening Las Vegas Valley Shear Zone. The Colorado Plateau-Basin and Range transition zone may be a long-lived tectonic boundary where this assumption may be especially ill-suited.

Variable shortening on the Main Frontal Thrust in Nepal

NASA Astrophysics Data System (ADS)

Almeida, R. V.; Hubbard, J.; Lee, Y. S.; Liberty, L. M.; Paudel, L.; Shrestha, A.; Sapkota, S. N.; Joshi, G.

2017-12-01

The Main Frontal Thrust (MFT) is the youngest, most active, and southernmost thrust system in the Himalaya. It is located in the footwall of the Main Boundary thrust (MBT), deforming Miocene to Pliocene age Siwalik Group rocks. Although often considered a single, continuous fault, in reality as many as four subparallel faults, spaced 5-30 km apart, make up this fault system. Estimates of total shortening across the MFT for eastern and central Nepal vary from 15 to 40 km, based on cross-sections and surface measurements. However, when the same methods are applied, shortening does not vary significantly along strike (Hirschmiller et al., 2014), suggesting contrasting methodologies rather than a difference in interpreted along strike structural history. Based on high resolution seismic reflection imaging, we present new interpretations of total shortening recorded by the MFT system in central vs. eastern Nepal (200 km apart), together with a detailed transect of field observations in central Nepal. Our structural interpretations demonstrate that the geological shortening recorded on the MFT ranges from >20 km in central Nepal to <1 km in far eastern Nepal. Geodetic measurements show only a slight decrease in interseismic convergence from central (15±1 mm/yr) to eastern Nepal (14±1 mm/yr) and therefore cannot explain this dramatic difference (Lindsey et al., in prep). Taken at face value, these results imply that the MBT must have been much more recently active in eastern Nepal ( 70 ka) than central Nepal ( 1.4 Ma). We propose an alternative model that does not require this dramatic difference in the age of the MFT. As one end-member, it is indeed possible that the MFT may have broken forward much more recently in the east. However, it is also possible that older MFT thrust sheets have formed, and then have been consumed as the MBT passively slid south in the hanging wall of the MFT. Distinguishing between these models is important not only for understanding the evolution of the MBT and MFT, but also plays a critical role in assessing the current geometry and earthquake hazard associated with the Main Himalayan Thrust, the décollement that underlies the entire system (e.g., Hubbard et al., 2016). We explore the implications of these two end-member models and identify ways in which each model could be tested.

Event sand layers suggesting the possibility of tsunami deposits identified in the upper Holocene sequence nearby the Kuwana fault, central Japan

NASA Astrophysics Data System (ADS)

Niwa, Y.; Sugai, T.; Matsuzaki, H.

2012-12-01

The Kuwana fault is located on coastal area situated on inner part of the Ise Bay, central Japan, which opens to the Nankai Trough. This reverse fault displaces a late Pleistocene terrace surface with 1 to 2 mm/yr of average vertical slip rate, and a topset of delta at several meters, respectively. And, this fault is estimated to have generated two historical earthquakes (the AD 745 Tempyo and the AD 1586 Tensho earthquakes). We identified two event sand layers from upper Holocene sequence on the upthrown side of the Kuwana fault. Upper Holocene deposits in this study area show prograding delta sequence; prodelta mud, delta front sandy silt to sand, and flood plain sand/mud, respectively, from lower to upper. Two sand layers intervene in delta front sandy silt layer, respectively. Lower sand layer (S1) shows upward-coarsening succession, whereas upper sand layer (S2) upward-fining succession. These sand layers contain sharp contact, rip-up crust, and shell fragment, indicating strong stream flow. Radiocarbon ages show that these strong stream flow events occurred between 3000 and 1600 years ago. Decreasing of salinity is estimated from decreasing trend of electrical conductivity (EC) across S1. Based on the possibility that decreasing of salinity can be occurred by shallowing of water depth caused by coseismic uplift, and that S1 can be correlated with previously known faulting event on the Kuwana fault, S1 is considered to be tsunami deposits caused by faulting on the Kuwana fault. On the other hand, S2, which cannot be correlated with previously known faulting events on the Kuwana fault, may be tsunami deposits by ocean-trench earthquake or storm deposits. In the presentation, we will discuss more detail correlation of these sand deposits not only in the upthrown side of the Kuwana fault, but also downthrown side of the fault.

Reexamination of the subsurface fault structure in the vicinity of the 1989 moment-magnitude-6.9 Loma Prieta earthquake, central California, using steep-reflection, earthquake, and magnetic data

USGS Publications Warehouse

Zhang, Edward; Fuis, Gary S.; Catchings, Rufus D.; Scheirer, Daniel S.; Goldman, Mark; Bauer, Klaus

2018-06-13

We reexamine the geometry of the causative fault structure of the 1989 moment-magnitude-6.9 Loma Prieta earthquake in central California, using seismic-reflection, earthquake-hypocenter, and magnetic data. Our study is prompted by recent interpretations of a two-part dip of the San Andreas Fault (SAF) accompanied by a flower-like structure in the Coachella Valley, in southern California. Initially, the prevailing interpretation of fault geometry in the vicinity of the Loma Prieta earthquake was that the mainshock did not rupture the SAF, but rather a secondary fault within the SAF system, because network locations of aftershocks defined neither a vertical plane nor a fault plane that projected to the surface trace of the SAF. Subsequent waveform cross-correlation and double-difference relocations of Loma Prieta aftershocks appear to have clarified the fault geometry somewhat, with steeply dipping faults in the upper crust possibly connecting to the more moderately southwest-dipping mainshock rupture in the middle crust. Examination of steep-reflection data, extracted from a 1991 seismic-refraction profile through the Loma Prieta area, reveals three robust fault-like features that agree approximately in geometry with the clusters of upper-crustal relocated aftershocks. The subsurface geometry of the San Andreas, Sargent, and Berrocal Faults can be mapped using these features and the aftershock clusters. The San Andreas and Sargent Faults appear to dip northeastward in the uppermost crust and change dip continuously toward the southwest with depth. Previous models of gravity and magnetic data on profiles through the aftershock region also define a steeply dipping SAF, with an initial northeastward dip in the uppermost crust that changes with depth. At a depth 6 to 9 km, upper-crustal faults appear to project into the moderately southwest-dipping, planar mainshock rupture. The change to a planar dipping rupture at 6–9 km is similar to fault geometry seen in the Coachella Valley.

Possible strain partitioning structure between the Kumano fore-arc basin and the slope of the Nankai Trough accretionary prism

NASA Astrophysics Data System (ADS)

Martin, Kylara M.; Gulick, Sean P. S.; Bangs, Nathan L. B.; Moore, Gregory F.; Ashi, Juichiro; Park, Jin-Oh; Kuramoto, Shin'ichi; Taira, Asahiko

2010-05-01

A 12 km wide, 56 km long, three-dimensional (3-D) seismic volume acquired over the Nankai Trough offshore the Kii Peninsula, Japan, images the accretionary prism, fore-arc basin, and subducting Philippine Sea Plate. We have analyzed an unusual, trench-parallel depression (a "notch") along the seaward edge of the fore-arc Kumano Basin, just landward of the megasplay fault system. This bathymetric feature varies along strike, from a single, steep-walled, ˜3.5 km wide notch in the northeast to a broader, ˜5 km wide zone with several shallower linear depressions in the southwest. Below the notch we found both vertical faults and faults which dip toward the central axis of the depression. Dipping faults appear to have normal offset, consistent with the extension required to form a bathymetric low. Some of these dipping faults may join the central vertical fault(s) at depth, creating apparent flower structures. Offset on the vertical faults is difficult to determine, but the along-strike geometry of these faults makes predominantly normal or thrust motion unlikely. We conclude, therefore, that the notch feature is the bathymetric expression of a transtensional fault system. By considering only the along-strike variability of the megasplay fault, we could not explain a transform feature at the scale of the notch. Strike-slip faulting at the seaward edge of fore-arc basins is also observed in Sumatra and is there attributed to strain partitioning due to oblique convergence. The wedge and décollement strength variations which control the location of the fore-arc basins may therefore play a role in the position where an along-strike component of strain is localized. While the obliquity of convergence in the Nankai Trough is comparatively small (˜15°), we believe it generated the Kumano Basin Edge Fault Zone, which has implications for interpreting local measured stress orientations and suggests potential locations for strain-partitioning-related deformation in other subduction zones.

VNIR reflectance spectroscopy of natural carbonate rocks: implication for remote sensing identification of fault damage zones

NASA Astrophysics Data System (ADS)

Traforti, Anna; Mari, Giovanna; Carli, Cristian; Demurtas, Matteo; Massironi, Matteo; Di Toro, Giulio

2017-04-01

Reflectance spectroscopy in the visible and near-infrared (VNIR) is a common technique used to study the mineral composition of Solar System bodies from remote sensed and in-situ robotic exploration. In the VNIR spectral range, both crystal field and vibrational overtone absorptions can be present with spectral characteristics (i.e. albedo, slopes, absorption band with different positions and depths) that vary depending on composition and texture (e.g. grain size, roughness) of the sensed materials. The characterization of the spectral variability related to the rock texture, especially in terms of grain size (i.e., both the size of rock components and the size of particulates), commonly allows to obtain a wide range of information about the different geological processes modifying the planetary surfaces. This work is aimed at characterizing how the grain size reduction associated to fault zone development produces reflectance variations in rock and mineral spectral signatures. To achieve this goal we present VNIR reflectance analysis of a set of fifteen rock samples collected at increasing distances from the fault core of the Vado di Corno fault zone (Campo Imperatore Fault System - Italian Central Apennines). The selected samples had similar content of calcite and dolomite but different grain size (X-Ray Powder Diffraction, optical and scanning electron microscopes analysis). Consequently, differences in the spectral signature of the fault rocks should not be ascribed to mineralogical composition. For each sample, bidirectional reflectance spectra were acquired with a Field-Pro Spectrometer mounted on a goniometer, on crushed rock slabs reduced to grain size <800, <200, <63, <10 μm and on intact fault zone rock slabs. The spectra were acquired on dry samples, at room temperature and normal atmospheric pressure. The source used was a Tungsten Halogen lamp with an illuminated spot area of ca. 0.5 cm2and incidence and emission angles of 30˚ and 0˚ respectively. The spectral analysis of the crushed and intact rock slabs in the VNIR spectral range revealed that in both cases, with increasing grain size: (i) the reflectance decreases (ii) VNIR spectrum slopes (i.e. calculated between wavelengths of 0.425 - 0.605 μm and 2.205 - 2.33 μm, respectively) and (iii) carbonate main absorption band depth (i.e. vibrational absorption band at wavelength of ˜2.3 μm) increase. In conclusion, grain size variations resulting from the fault zone evolution (e.g., cumulated slip or development of thick damage zones) produce reflectance variations in rocks and mineral spectral signatures. The remote sensing analysis in the VNIR spectral range can be applied to identify the spatial distribution and extent of fault core and damage zone domains for industrial and seismic hazard applications. Moreover, the spectral characterization of carbonate-built rocks can be of great interest for the surface investigation of inner planets (e.g. Earth and Mars) and outer bodies (e.g. Galilean icy satellites). On these surfaces, carbonate minerals at different grain sizes are common and usually related to water and carbon distribution, with direct implications for potential life outside Earth (e.g. Mars).

New constraints on slip-rates, recurrence intervals, and strain partitioning beneath Pyramid Lake, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eisses, Amy

A high-resolution CHIRP seismic survey of Pyramid Lake, Nevada, located within the northern Walker Lane Deformation Belt, was conducted in summer 2010. Seismic CHIRP data with submeter vertical accuracy, together with piston and gravity cores, were used to calculate Holocene vertical slip rates, relative earthquake timing, and produce the first complete fault map beneath the lake. More than 500 line-kilometers of CHIRP data imaged complex fault patterns throughout the basin. Fault architecture beneath Pyramid Lake highlights a polarity flip, where down-to-the west patterns of sedimentation near the dextral Pyramid Lake fault to the south give way to down-to-the-east geometries tomore » the north within a mostly normal (i.e., Lake Range fault) and transtensional environment. The Lake Range fault predominantly controls extensional deformation within the northern two-thirds of the basin and exhibits varying degrees of asymmetric tilting and divergence due to along-strike segmentation. This observation is likely a combination of fault segments splaying onshore moving the focus of extension away from the lake coupled with some true along-strike differences in slip-rate. The combination of normal and oblique-slip faults in the northern basin gives Pyramid Lake its distinctive “fanning open to the north” tectonic geometry. The dense network of oblique-slip faults in the northwestern region of the lake, in contrast to the well-defined Lake Range fault, are short and discontinuous in nature, and possible represent a nascent shear zone. Preliminary vertical slip-rates measured across the Lake Range and other faults provide new estimates on the extension across the Pyramid Lake basin. A minimum vertical slip rate of ~1.0 mm/yr is estimated along the Lake Range fault, which yields a potential earthquake magnitude range between M6.4 and M7.0. A rapid influx of sediment was deposited shortly after the end of the Tioga glaciation somewhere between 12.5 ka to 9.5 ka and provides a punctuated short-term record of little to no slip on the Lake Range fault. In contrast, for the past 9,500 years, the basin has experienced a decrease in sedimentation rate, but an escalation in earthquake activity on the Lake Range fault, with the potential of 3 or 4 major earthquakes assuming a characteristic offset of 2.5 m per event. Regionally, our CHIRP investigation helps to reveal how strain is partitioned along the boundary between the eastern edge of the Walker Lane Deformation Belt and the northwest Great Basin proper.« less

Low-frequency earthquakes reveal punctuated slow slip on the deep extent of the Alpine Fault, New Zealand

USGS Publications Warehouse

Chamberlain, Calum J.; Shelly, David R.; Townend, John; Stern, T.A.

2014-01-01

We present the first evidence of low-frequency earthquakes (LFEs) associated with the deep extension of the transpressional Alpine Fault beneath the central Southern Alps of New Zealand. Our database comprises a temporally continuous 36 month-long catalog of 8760 LFEs within 14 families. To generate this catalog, we first identify 14 primary template LFEs within known periods of seismic tremor and use these templates to detect similar events in an iterative stacking and cross-correlation routine. The hypocentres of 12 of the 14 LFE families lie within 10 km of the inferred location of the Alpine Fault at depths of approximately 20–30 km, in a zone of high P-wave attenuation, low P-wave speeds, and high seismic reflectivity. The LFE catalog consists of persistent, discrete events punctuated by swarm-like bursts of activity associated with previously and newly identified tremor periods. The magnitudes of the LFEs range between ML – 0.8 and ML 1.8, with an average of ML 0.5. We find that the frequency-magnitude distribution of the LFE catalog both as a whole and within individual families is not consistent with a power law, but that individual families' frequency-amplitude distributions approximate an exponential relationship, suggestive of a characteristic length-scale of failure. We interpret this LFE activity to represent quasi-continuous slip on the deep extent of the Alpine Fault, with LFEs highlighting asperities within an otherwise steadily creeping region of the fault.

Faults and Flows

NASA Image and Video Library

2014-10-20

Lava flows of Daedalia Planum can be seen at the top and bottom portions of this image from NASA 2001 Mars Odyssey spacecraft. The ridge and linear depression in the central part of the image are part of Mangala Fossa, a fault bounded graben.

Active out-of-sequence thrust faulting in the central Nepalese Himalaya.

PubMed

Wobus, Cameron; Heimsath, Arjun; Whipple, Kelin; Hodges, Kip

2005-04-21

Recent convergence between India and Eurasia is commonly assumed to be accommodated mainly along a single fault--the Main Himalayan Thrust (MHT)--which reaches the surface in the Siwalik Hills of southern Nepal. Although this model is consistent with geodetic, geomorphic and microseismic data, an alternative model incorporating slip on more northerly surface faults has been proposed to be consistent with these data as well. Here we present in situ cosmogenic 10Be data indicating a fourfold increase in millennial timescale erosion rates occurring over a distance of less than 2 km in central Nepal, delineating for the first time an active thrust fault nearly 100 km north of the surface expression of the MHT. These data challenge the view that rock uplift gradients in central Nepal reflect only passive transport over a ramp in the MHT. Instead, when combined with previously reported 40Ar-39Ar data, our results indicate persistent exhumation above deep-seated, surface-breaking structures at the foot of the high Himalaya. These results suggest that strong dynamic interactions between climate, erosion and tectonics have maintained a locus of active deformation well to the north of the Himalayan deformation front.

Initiation and development of the southern California uplift along its northern margin

USGS Publications Warehouse

Stein, R.S.; Thatcher, W.; Castle, R.O.

1979-01-01

Analysis of three first-order leveling lines that traverse the White Wolf fault (site of the 1952 M = 7.7 earthquake), each resurveyed nine times between 1926 and 1974, reveals probable preseismic tilting, major coseismic movements, and a spatial association between these movements and the subsequently recognized southern California uplift. In examining the vertical control record, we have both searched for evidence of systematic errors and excluded from consideration portions of the lines contaminated by subsurface fluid and gas extraction. Movements have been referred to an invariant datum based on the 1926 position of tidal BM 8 in San Pedro, corrected for subsequent eustatic sea-level change. An 8 ??rad up-to-the-north preseismic tilt (6 cm/7.5 km) was apparently recorded on two adjacent line segments within 10 km of the 1952 epicenter between 1942 and 1947. It is possible, however, that this tilt was in part caused by extraction-induced subsidence at one of the six releveled benchmarks. Data also show evidence of episodic tilts that are not earthquake related. At the junction of the Garlock and San Andreas faults, for example, an ???5 ??rad up-to-the-north tilt (7.2 cm/???16 km) took place between Lebec and Grapevine within three months during 1964. Comparison of the 1947 and 1953 surveys, which includes the coseismic interval, shows that the SW-fault end (nearest the epicenter) and the central fault reach sustained four times the uplift recorded at the NE end of the fault (+72 cm SW, +53 cm Central, +16 cm NE). A regional postseismic uplift of 4 cm extended ???25 km to either side of the fault after the main event, from 1953 to 1956. An interval of relative quiescence followed at least through 1959, in which the elevation change did not exceed ??3 cm. The detailed pattern of aseismic uplift demonstrates that movement proceeded in space-time pulses: one half of the uplift at the SW-fault end and extending southward occurred between 1959 and 1961, one half of the uplift at the NE-fault end and extending eastward occurred between 1961 and 1965, while the central fault reach sustained successive pulses of subsidence, uplift, and collapse (-4 cm, 1953-1960; +7 cm, 1960-1965; -2 cm, 1965-1970). In addition, the number of aftershocks concentrated near the fault ends increased in the NE relative to the SW from 1952 to 1974. These observations suggest that the aseismic uplift may have migrated northeastward from 1959 to 1965 at an approximate rate of 7-16 km/yr. Evidence for a mechanical coupling between the earthquake and the subsequent aseismic uplift is equivocal. At both fault ends, the major NWbounding flexure or tilted front of the southern California uplift is spatially coincident with the coseismic flexure that preceded it. In addition, the postulated migration of vertical deformation is similar to the 1952 seismic event in which the rupture initiated at the SW end of the fault and then propagated to the NE-fault end. However, the spatial distribution of aseismic uplift, nearly identical at both fault ends and to the south and east, and near zero in the central fault reach, is distinctly different from the nonuniform and localized coseismic deformation. ?? 1979.

Investigation of lineaments on Skylab and ERTS images of Peninsular Ranges, Southwestern California

NASA Technical Reports Server (NTRS)

Merifield, P. M. (Principal Investigator); Lamar, D. L.

1974-01-01

The author has identified the following significant results. Northwest trending faults such as the Elsinore and San Jacinto are prominently displayed on Skylab and ERTS images of the Peninsular Ranges, southern California. Northeast, north-south, and west-north-west trending lineaments and faults are also apparent on satellite imagery. Several of the lineaments represent previously unmapped faults. Other lineaments are due to erosion along foliation directions and sharp bends in basement rock contacts rather than faulting. The northeast trending Thing Valley fault appears to be offset by the south branch of the Elsinore fault near Agua Caliente Hot Springs. Larger horizontal displacement along the Elsinore fault further northwest may be distributed along several faults which branch from the Elsinore fault in the Peninsular Ranges. The northeast and west-northwest trending faults are truncated by the major northwest trending faults and appear to be restricted to basement terrane. Limited data on displacement direction suggests that the northeast and west-northwest trending faults formed in response to an earlier period of east-northeast, west-southwest crustal shortening. Such a stress system is consistent with the plate tectonic model of a subduction zone parallel to the continental margin suggested in the late Mesozoic and early Tertiary.

Evidence for a Battle Mountain-Eureka crustal fault zone, north-central Nevada, and its relation to Neoproterozoic-Early Paleozoic continental breakup

USGS Publications Warehouse

Grauch, V.J.S.; Rodriguez, B.D.; Bankey, V.; Wooden, J.L.

2003-01-01

Combined evidence from gravity, radiogenic isotope, and magnetotelluric (MT) data indicates a crustal fault zone that coincides with the northwest-trending Battle Mountain-Eureka (BME) mineral trend in north-central Nevada, USA. The BME crustal fault zone likely originated during Neoproterozoic-Early Paleozoic rifting of the continent and had a large influence on subsequent tectonic events, such as emplacement of allochthons and episodic deformation, magmatism, and mineralization throughout the Phanerozoic. MT models show the fault zone is about 10 km wide, 130-km long, and extends from 1 to 5 km below the surface to deep crustal levels. Isotope data and gravity models imply the fault zone separates crust of fundamentally different character. Geophysical evidence for such a long-lived structure, likely inherited from continental breakup, defies conventional wisdom that structures this old have been destroyed by Cenozoic extensional processes. Moreover, the coincidence with the alignment of mineral deposits supports the assertion by many economic geologists that these alignments are indicators of buried regional structures.

Age and isotopic systematics of Cretaceous borehole and surface samples from the greater Los Angeles Basin region: Implications for the types of crust that might underlie Los Angeles and their distribution along late Cenozoic fault systems

USGS Publications Warehouse

Premo, Wayne R.; Morton, Douglas M.; Kistler, Ronald W.

2014-01-01

Nine U-Pb zircon ages were determined on plutonic rocks sampled from surface outcrops and rock chips of drill core from boreholes within the greater Los Angeles Basin region. In addition, lead-strontium-neodymium (Pb-Sr-Nd) whole-rock isotopic data were obtained for eight of these samples. These results help to characterize the crystalline basement rocks hidden in the subsurface and provide information that bears on the tectonic history of the myriad of fault systems that have dissected the Los Angeles region over the past 15 m.y. Seven of the nine samples have U-Pb ages ranging from 115 to 103 Ma and whole-rock Pb-Sr-Nd isotopic characteristics that indicate the crystalline basement underneath the greater Los Angeles Basin region is mostly part of the Peninsular Ranges batholith. Furthermore, these data are interpreted as evidence for (1) the juxtaposition of mid-Cretaceous, northern Peninsular Ranges batholith plutonic rocks against Late Cretaceous plutonic rocks of the Transverse Ranges in the San Fernando Valley, probably along the Verdugo fault; (2) the juxtaposition of older northwestern Peninsular Ranges batholith rocks against younger northeastern Peninsular Ranges batholith rocks in the northern Puente Hills, implying transposition of northeastern Peninsular Ranges batholith rocks to the west along unrecognized faults beneath the Chino Basin; and (3) juxtaposition of northern Peninsular Ranges batholith plutonic rocks against Late Cretaceous plutonic rocks of the Transverse Ranges along the San Jose fault in the northern San Jose Hills at Ganesha Park. These mainly left-lateral strike-slip faults of the eastern part of the greater Los Angeles Basin region could be the result of block rotation within the adjacent orthogonal, right-lateral, Elsinore-Whittier fault zone to the west and the subparallel San Jacinto fault zone to the east. The San Andreas fault system is the larger, subparallel, driving force further to the east.

Structural architecture of the central Brooks Range foothills, Alaska

USGS Publications Warehouse

Moore, Thomas E.; Potter, Christopher J.; O'Sullivan, Paul B.

2002-01-01

Five structural levels underlie the Brooks Range foothills, from lowest to highest: (1) autochthon, at a depth of ~9 km; (2) Endicott Mountains allochthon (EMA), thickest under the northern Brooks Range (>15 km) and wedging out northward above the autochthon; (3) higher allochthons (HA), with a composite thickness of 1.5+ km, wedging out northward at or beyond the termination of EMA; (4) Aptian-Albian Fortress Mountain Formation (FM), deposited unconformably on deformed EMA and HA and thickening northward into a >7-km-thick succession of deformed turbidites (Torok Formation); (5) gently folded Albian-Cenomanian deltaic deposits (Nanushuk Group). The dominant faulting pattern in levels 2-3 is thin-skinned thrusting and thrust-related folds formed before deposition of Cretaceous strata. These structures are cut by younger steeply south-dipping reverse faults that truncate and juxtapose structural levels 1-4 and expose progressively deeper structural levels to the south. Structural levels 4-5 are juxtaposed along a north-dipping zone of south-vergent folds and thrusts. Stratigraphic and fission-track age data suggest a kinematic model wherein the foothills belt was formed first, by thrusting of HA and EMA as deformational wedges onto the regionally south-dipping authochon at 140-120Ma. After deposition of FM and Torok during mid-Cretaceous hinterland extension and uplift, a second episode of contractional deformation at 60 Ma shortened the older allochthonous deformational wedges (EMA, HA) and overlying strata on north-vergent reverse faults. To the north, where the allochthons wedge out, shortening caused duplexing in the Torok and development of a triangle zone south of the Tuktu escarpment.

Trenching in the New Madrid seismic zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-01-01

Trenching studies of the San Andreas fault have been of great value to geologists in California for determining not only the prehistoric occurrences of earthquakes on the fault but also the age of these movements. In the New Madrid seismic zone, US Geological Survey scientists have been trenching across suspected faults to try to assess earthquake frequency in the Central US. The following photographs document these trenching studies.

Geophysical investigations of the geologic and hydrothermal framework of the Pilgrim Springs Geothermal Area, Alaska

USGS Publications Warehouse

Glen, Jonathan; McPhee, Darcy K.; Bedrosian, Paul A.

2014-01-01

Pilgrim Hot Springs, located on the Seward Peninsula in west-central Alaska, is characterized by hot springs, surrounding thawed regions, and elevated lake temperatures. The area is of interest because of its potential for providing renewable energy for Nome and nearby rural communities. We performed ground and airborne geophysical investigations of the Pilgrim Springs geothermal area to identify areas indicative of high heat flow and saline geothermal fluids, and to map key structures controlling hydrothermal fluid flow. Studies included ground gravity and magnetic measurements, as well as an airborne magnetic and frequency-domain electromagnetic (EM) survey. The structural and conceptual framework developed from this study provides critical information for future development of this resource and is relevant more generally to our understanding of geothermal systems in active extensional basins. Potential field data reveal the Pilgrim area displays a complex geophysical fabric reflecting a network of intersecting fault and fracture sets ranging from inherited basement structures to Tertiary faults. Resistivity models derived from the airborne EM data reveal resistivity anomalies in the upper 100 m of the subsurface that suggest elevated temperatures and the presence of saline fluids. A northwest trending fabric across the northeastern portion of the survey area parallels structures to the east that may be related to accommodation between the two major mountain ranges south (Kigluaik) and east (Bendeleben) of Pilgrim Springs. The area from the springs southward to the range front, however, is characterized by east-west trending, range-front-parallel anomalies likely caused by late Cenozoic structures associated with north-south extension that formed the basin. The area around the springs (~10 km2 ) is coincident with a circular magnetic high punctuated by several east-west trending magnetic lows, the most prominent occurring directly over the springs. These features possibly result from hydrothermal alteration imposed by fluids migrating along intra-basin faults related to recent north-south extension. The Pilgrim River valley is characterized by a NE-elongate gravity low that reveals a basin extending to depths of ~300 m beneath Pilgrim Springs and deepening to ~800 m to the southwest. The margins of the gravity low are sharply defined by northeasttrending gradients that probably reflect the edges of fault-bounded structural blocks. The southeastern edge of the low, which lies very close to the springs, also corresponds with prominent NE-striking anomalies seen in magnetic and resistivity models. Together, these features define a structure we refer to as the Northeast Fault. The location of the hot springs appears to be related to the intersection of the Northeast Fault with a N-oriented structure marked by the abrupt western edge of a resistivity low surrounding the hot springs. While the hot springs represent the primary outflow of geothermal fluids, additional outflow extends from the springs northeast along the Northeast fault to another thaw zone that we interpret to be a secondary region of concentrated upflow of geothermal fluids. The Northeast Fault apparently controls shallow geothermal fluid flow, and may also provide an important pathway conveying deep fluids to the shallow subsurface. We suggest that geothermal fluids may derive from a reservoir residing beneath the sediment basin southwest of the springs. If so, the shape of the basin, which narrows and shallows towards the springs, may funnel fluids beneath the springs where they intersect the Northeast Fault allowing them to reach the surface. An alternative pathway for reservoir fluids to reach intermediate to shallow depths may be afforded by the main Kigluaik range front fault that coincides with a resistivity anomaly possibly resulting from fluid flow and associated hydrothermal mineralization occurring within the fault zone.

The role of E-W basement faults in the Mesozoic geodynamic evolution of the Gafsa and Chotts basins, south-central Tunisia

NASA Astrophysics Data System (ADS)

Amri, Dorra Tanfous; Dhahri, Ferid; Soussi, Mohamed; Gabtni, Hakim; Bédir, Mourad

2017-10-01

The Gafsa and Chotts intracratonic basins in south-central Tunisia are transitional zones between the Atlasic domain to the north and the Saharan platform to the south. The principal aim of this paper is to unravel the geodynamic evolution of these basins following an integrated approach including seismic, well log and gravity data. These data are used to highlight the tectonic control on the deposition of Jurassic and Lower Cretaceous series and to discuss the role of the main faults that controlled the basin architecture and Cretaceous-Tertiary inversion. The horizontal gravity gradient map of the study area highlights the pattern of discontinuities within the two basins and reveals the presence of deep E-W basement faults. Primary attention is given to the role played by the E-W faults system and that of the NW-SE Gafsa fault which was previously considered active since the Jurassic. Facies and thickness analyses based on new seismic interpretation and well data suggest that the E-W-oriented faults controlled the subsidence distribution especially during the Jurassic. The NW-SE faults seem to be key structures that controlled the basins paleogeography during Late Cretaceous-Cenozoic time. The upper Triassic evaporite bodies, which locally outline the main NW-SE Gafsa fault, are regarded as intrusive salt bodies rather than early diapiric extrusions as previously interpreted since they are rare and occurred only along main strike-slip faults. In addition, seismic lines show that Triassic rocks are deep and do not exhibit true diapiric features.

Basement-involved faults and deep structures in the West Philippine Basin: constrains from gravity field

NASA Astrophysics Data System (ADS)

Wang, Gang; Jiang, Suhua; Li, Sanzhong; Zhang, Huixuan; Lei, Jianping; Gao, Song; Zhao, Feiyu

2017-06-01

To reveal the basement-involved faults and deep structures of the West Philippine Basin (WPB), the gravitational responses caused by these faults are observed and analyzed based on the latest spherical gravity model: WGM2012 Model. By mapping the free-air and Bouguer gravity anomalies, several main faults and some other linear structures are located and observed in the WPB. Then, by conducting a 2D discrete multi-scale wavelet decomposition, the Bouguer anomalies are decomposed into the first- to eighth-order detail and approximation fields (the first- to eighth-order Details and Approximations). The first- to third-order Details reflect detailed and localized geological information of the crust at different depths, and of which the higher-order reflects gravity field of the deeper depth. The first- to fourth-order Approximations represent the regional gravity fields at different depths of the crust, respectively. The fourth-order Approximation represents the regional gravity fluctuation caused by the density inhomogeneity of Moho interface. Therefore, taking the fourth-order Approximation as input, and adopting Parker-Oldenburg interactive inversion, We calculated the depth of Moho interface in the WPB. Results show that the Moho interface depth in the WPB ranges approximately from 8 to 12 km, indicating that there is typical oceanic crust in the basin. In the Urdaneta Plateau and the Benham Rise, the Moho interface depths are about 14 and 16 km, respectively, which provides a piece of evidence to support that the Banham Rise could be a transitional crust caused by a large igneous province. The second-order vertical derivative and the horizontal derivatives in direction 0° and 90° are computed based on the data of the third-order Detail, and most of the basement-involved faults and structures in the WPB, such as the Central Basin Fault Zone, the Gagua Ridge, the Luzon-Okinawa Fault Zone, and the Mindanao Fault Zone are interpreted by the gravity derivatives.

Topography and tectonics of the central New Madrid seismic zone: Results of numerical experiements using a three-dimensional boundary element program

NASA Technical Reports Server (NTRS)

Gomberg, Joan; Ellis, Michael

1994-01-01

We present results of a series of numerical experiments designed to test hypothetical mechanisms that derive deformation in the New Madrid seismic zone. Experiments are constrained by subtle topography and the distribution of seismicity in the region. We use a new boundary element algorithm that permits calcuation of the three-dimensional deformation field. Surface displacement fields are calculated for the New Madrid zone under both far-field (plate tectonics scale) and locally derived driving strains. Results demonstrate that surface displacement fields cannot distinguish between either a far-field simple or pure shear strain field or one that involves a deep shear zone beneath the upper crustal faults. Thus, neither geomorphic nor geodetic studies alone are expected to reveal the ultimate driving mechanism behind the present-day deformation. We have also tested hypotheses about strain accommodation within the New Madrid contractional step-over by including linking faults, two southwest dipping and one vertical, recently inferred from microearthquake data. Only those models with step-over faults are able to predict the observed topography. Surface displacement fields for long-term, relaxed deformation predict the distribution of uplift and subsidence in the contractional step-over remarkably well. Generation of these displacement fields appear to require slip on both the two northeast trending vertical faults and the two dipping faults in the step-over region, with very minor displacements occurring during the interseismic period when the northeast trending vertical faults are locked. These models suggest that the gently dippling central step-over fault is a reverse fault and that the steeper fault, extending to the southeast of the step-over, acts as a normal fault over the long term.

Tectonic implications of the 2017 Ayvacık (Çanakkale) earthquakes, Biga Peninsula, NW Turkey

NASA Astrophysics Data System (ADS)

Özden, Süha; Över, Semir; Poyraz, Selda Altuncu; Güneş, Yavuz; Pınar, Ali

2018-04-01

The west to southwestward motion of the Anatolian block results from the relative motions between the Eurasian, Arabian and African plates along the right-lateral North Anatolian Fault Zone in the north and left-lateral East Anatolian Fault Zone in the east. The Biga Peninsula is tectonically influenced by the Anatolian motion originating along the North Anatolian Fault Zone which splits into two main (northern and southern) branches in the east of Marmara region: the southern branch extends towards the Biga Peninsula which is characterized by strike-slip to oblique normal faulting stress regime in the central to northern part. The southernmost part of peninsula is characterized by a normal to oblique faulting stress regime. The analysis of both seismological and structural field data confirms the change of stress regime from strike-slip character in the center and north to normal faulting character in the south of peninsula where the earthquake swarm recently occurred. The earthquakes began on 14 January 2017 (Mw: 4.4) on Tuzla Fault and migrated southward along the Kocaköy and Babakale's stepped-normal faults of over three months. The inversion of focal mechanisms yields a normal faulting stress regime with an approximately N-S (N4°E) σ3 axis. The inversion of earthquakes occurring in central and northern Biga Peninsula and the north Aegean region gives a strike-slip stress regime with approximately WNW-ESE (N85°W) σ1 and NNE-SSW (N17°E) σ3 axis. The strike-slip stress regime is attributed to westward Anatolian motion, while the normal faulting stress regime is attributed to both the extrusion of Anatolian block and the slab-pull force of the subducting African plate along the Hellenic arc.

South Virgin-White Hills detachment fault system of SE Nevada and NW Arizona: Applying apatite fission track thermochronology to constrain the tectonic evolution of a major continental detachment fault

NASA Astrophysics Data System (ADS)

Fitzgerald, Paul G.; Duebendorfer, Ernest M.; Faulds, James E.; O'Sullivan, Paul

2009-04-01

The South Virgin-White Hills detachment (SVWHD) in the central Basin and Range province with an along-strike extent of ˜60 km is a major continental detachment fault system. Displacement on the SVWHD decreases north to south from ˜17 to <6 km. This is accompanied by a change in fault and footwall rock type from mylonite overprinted by cataclasite to chlorite cataclasite and then fault breccia reflecting decreasing fault displacement and footwall exhumation. Apatite fission track (AFT) thermochronology was applied both along-strike and across-strike to assess this displacement gradient. The overall thermal history reflects Laramide cooling (˜75 Ma) and then rapid cooling beginning in the late early Miocene. Age patterns reflect some complexity but extension along the SVWHD appears synchronous with rapid cooling initiated at ˜17 Ma due to tectonic exhumation. Slip rate is more rapid (˜8.6 km/Ma) in the north compared to ˜1 km/Ma in the south. The displacement gradient results from penecontemporaneous along-strike motion and formation of the SVWHD by linkage of originally separate fault segments that have differential displacements and hence differential slip rates. East-west transverse structures likely play a role in linkage of different fault segments. The preextension paleogeothermal gradient is well constrained in the Gold Butte block as 18-20°C/km. We present a new thermochronologic approach to constrain fault dip during slip, treating the vertical exhumation rate and the slip as vectors, with the angle between them used to constrain fault dip during slip through the closure temperature of a particular thermochronometer. AFT data from the western rim of the Colorado Plateau constrain the initiation of timing of cooling associated with the Laramide Orogeny at ˜75 Ma, and a reheating event in the late Eocene/early Oligocene associated with burial by sediments ("rim gravels") most likely shed from the Kingman High to the west of the plateau.

Late Mesozoic and Cenozoic thermotectonic evolution of the central Brooks Range and adjacent North Slope foreland basin, Alaska: Including fission track results from the Trans-Alaska Crustal Transect (TACT)

USGS Publications Warehouse

O'Sullivan, P. B.; Murphy, J.M.; Blythe, A.E.

1997-01-01

Apatite fission track data are used to evaluate the thermal and tectonic history of the central Brooks Range and the North Slope foreland basin in northern Alaska along the northern leg of the Trans-Alaska Crustal Transect (TACT). Fission track analyses of the detrital apatite grains in most sedimentary units resolve the timing of structures and denudation within the Brooks Range, ranging in scale from the entire mountain range to relatively small-scale folds and faults. Interpretation of the results indicates that rocks exposed within the central Brooks Range cooled rapidly from paleotemperatures 110?? to 50??C during discrete episodes at ???100??5 Ma, ???60??4 Ma, and ???24??3 Ma, probably in response to kilometer-scale denudation. North of the mountain front, rocks in the southern half of the foreland basin were exposed to maximum paleotemperatures 110??C in the Late Cretaceous to early Paleocene as a result of burial by Upper Jurassic and Cretaceous sedimentary rocks. Rapid cooling from these elevated paleotemperatures also occurred due to distinct episodes of kilometer-scale denudation at ???60??4 Ma, 46??3 Ma, 35??2 Ma, and ???24??3 Ma. Combined, the apatite analyses indicate that rocks exposed along the TACT line through the central Brooks Range and foreland basin experienced episodic rapid cooling throughout the Late Cretaceous and Cenozoic in response to at least three distinct kilometer-scale denudation events. Future models explaining orogenic events in northern Alaska must consider these new constraints from fission track thermochronology. Copyright 1997 by the American Geophysical Union.

Paleoseismic evidence for dynamic surface rupturing in an intraplate setting (Lower Rhine Embayment, central Europe)

NASA Astrophysics Data System (ADS)

Kuebler, S.; Friedrich, A. M.; Strecker, M. R.

2011-12-01

One of the most enigmatic problems in intraplate earthquake geology is the spatio-temporal recurrence pattern of large earthquakes. Intraplate regions such as the New Madrid seismic zone or the central European rift system are subject to considerable seismic hazards, because fault activity is highly disparate in space and time and our knowledge about the recurrence of large earthquakes is still rudimentary. The current debate in central Europe ranges from slip dominated by repeated large coseismic events to slip dominated by aseismic creep. Here, field evidence in support of the former is sparse, and hence, some authors concluded that many faults move by slow aseismic creep rather than by ground rupturing earthquakes. We report new results from a paleoseismic study carried out in the Lower Rhine Embayment across a subsidiary normal fault in the area of Germany's largest historical earthquake (1756 AD, ML 6.2±0.2) that clearly revealed field evidence of dynamic surface faulting. At the trench site, the fault is covered by <5 m-thick Holocene fluvial gravel and flood deposits overlaying Devonian shale. We mapped a surface offset of ~1 m and a ~10 m wide zone of localized deformation expressed by abundant fractures with aligned and broken clasts extending vertically throughout the entire gravel. Mapping of 237 fractured clasts and the long-axis orientation of ~10.000 clasts defines a deformation zone coinciding with the surface offset and two offset markers within the gravel layers. We interpret these features as the result of coseismic deformation at the near-surface end of the rupture. We rule out alternative processes which may lead to fracturing of pebbles such as freeze-thaw weathering or sediment loading effects, since both the gravel fabric and fracture planes coincide well with the fault orientation. We preclude slow deformation due to aseismic creep as governing process to cause rupturing of pebbles this close to the surface, as this would require an overburden stress of several hundreds of meters according to modelling results (e. g. Eidelmann, 1992, Geology). With a significantly smaller overburden, as in this study, a high differential acceleration force, such as a shock wave produced by an earthquake rupture or a seismic wave would be needed to overcome the pebble's shear resistance. Preliminary radiocarbon data bracket the youngest event horizon to Latest Holocene age. In conclusion, we identified coseismic deformation at the trench site, because special conditions produced a number of features not usually observed in other fault exposures. The thin sedimentary cover (<5 m) above basement rocks and the high groundwater table, which may reduce the shear strength of the pebbles, may have played an important role in producing this deformation pattern. Our results imply that large surface rupturing earthquakes in low-strain intraplate regions may be more common than previously thought.

Near-ridge seamount chains in the northeastern Pacific Ocean

NASA Astrophysics Data System (ADS)

Clague, David A.; Reynolds, Jennifer R.; Davis, Alicé S.

2000-07-01

High-resolution bathymetry and side-scan data of the Vance, President Jackson, and Taney near-ridge seamount chains in the northeast Pacific were collected with a hull-mounted 30-kHz sonar. The central volcanoes in each chain consist of truncated cone-shaped volcanoes with steep sides and nearly flat tops. Several areas are characterized by frequent small eruptions that result in disorganized volcanic regions with numerous small cones and volcanic ridges but no organized truncated conical structure. Several volcanoes are crosscut by ridge-parallel faults, showing that they formed within 30-40 km of the ridge axis where ridge-parallel faulting is still active. Magmas that built the volcanoes were probably transported through the crust along active ridge-parallel faults. The volcanoes range in volume from 11 to 187 km3, and most have one or more multiple craters and calderas that modify their summits and flanks. The craters (<1 km diameter) and calderas (>1 km diameter) range from small pit craters to calderas as large as 6.5×8.5 km, although most are 2-4 km across. Crosscutting relationships commonly show a sequence of calderas stepping toward the ridge axis. The calderas overlie crustal magma chambers at least as large as those that underlie Kilauea and Mauna Loa Volcanoes in Hawaii, perhaps 4-5 km in diameter and ˜1-3 km below the surface. The nearly flat tops of many of the volcanoes have remnants of centrally located summit shields, suggesting that their flat tops did not form from eruptions along circumferential ring faults but instead form by filling and overflowing of earlier large calderas. The lavas retain their primitive character by residing in such chambers for only short time periods prior to eruption. Stored magmas are withdrawn, probably as dikes intruded into the adjacent ocean crust along active ridge-parallel faults, triggering caldera collapse, or solidified before the next batch of magma is intruded into the volcano, probably 1000-10,000 years later. The chains are oriented parallel to subaxial asthenospheric flow rather than absolute or relative plate motion vectors. The subaxial asthenospheric flow model yields rates of volcanic migration of 3.4, 3.3 and 5.9 cm yr-1 for the Vance, President Jackson, and Taney Seamounts, respectively. The modeled lifespans of the individual volcanoes in the three chains vary from 75 to 95 kyr. These lifespans, coupled with the geologic observations based on the bathymetry, allow us to construct models of magma supply through time for the volcanoes in the three chains.

Distribution and Characteristics of Repeating Earthquakes in Northern California

NASA Astrophysics Data System (ADS)

Waldhauser, F.; Schaff, D. P.; Zechar, J. D.; Shaw, B. E.

2012-12-01

Repeating earthquakes are playing an increasingly important role in the study of fault processes and behavior, and have the potential to improve hazard assessment, earthquake forecast, and seismic monitoring capabilities. These events rupture the same fault patch repeatedly, generating virtually identical seismograms. In California, repeating earthquakes have been found predominately along the creeping section of the central San Andreas Fault, where they are believed to represent failing asperities on an otherwise creeping fault. Here, we use the northern California double-difference catalog of 450,000 precisely located events (1984-2009) and associated database of 2 billion waveform cross-correlation measurements to systematically search for repeating earthquakes across various tectonic regions. An initial search for pairs of earthquakes with high-correlation coefficients and similar magnitudes resulted in 4,610 clusters including a total of over 26,000 earthquakes. A subsequent double-difference re-analysis of these clusters resulted in 1,879 sequences (8,640 events) where a common rupture area can be resolved to the precision of a few tens of meters or less. These repeating earthquake sequences (RES) include between 3 and 24 events with magnitudes up to ML=4. We compute precise relative magnitudes between events in each sequence from differential amplitude measurements. Differences between these and standard coda-duration magnitudes have a standard deviation of 0.09. The RES occur throughout northern California, but RES with 10 or more events (6%) only occur along the central San Andreas and Calaveras faults. We are establishing baseline characteristics for each sequence, such as recurrence intervals and their coefficient of variation (CV), in order to compare them across tectonic regions. CVs for these clusters range from 0.002 to 2.6, indicating a range of behavior between periodic occurrence (CV~0), random occurrence, and temporal clustering. 10% of the RES show burst-like behavior with mean recurrence times smaller than one month. 5% of the RES have mean recurrence times greater than one year and include more than 10 earthquakes. Earthquakes in the 50 most periodic sequences (CV<0.2) do not appear to be predictable by either time- or slip-predictable models, consistent with previous findings. We demonstrate that changes in recurrence intervals of repeating earthquakes can be routinely monitored. This is especially important for sequences with CV~0, as they may indicate changes in the loading rate. We also present results from retrospective forecast experiments based on near-real time hazard functions.

Near-Surface Structure and Velocities of the Northeastern Santa Cruz Mountains and the Western Santa Clara Valley, California, From Seismic Imaging

USGS Publications Warehouse

Catchings, R.D.; Gandhok, G.; Goldman, M.R.; Steedman, Clare

2007-01-01

Introduction The Santa Clara Valley (SCV) is located in the southern San Francisco Bay area of California and is bounded by the Santa Cruz Mountains to the southwest, the Diablo Ranges to the northeast, and the San Francisco Bay to the north (Fig. 1). The SCV, which includes the City of San Jose, numerous smaller cities, and much of the high-technology manufacturing and research area commonly referred to as the Silicon Valley, has a population in excess of 1.7 million people (2000 U. S. Census;http://quickfacts.census.gov/qfd/states/06/06085.html The SCV is situated between major active faults of the San Andreas Fault system, including the San Andreas Fault to the southwest and the Hayward and Calaveras faults to the northeast, and other faults inferred to lie beneath the alluvium of the SCV (CWDR, 1967; Bortugno et al., 1991). The importance of the SCV as a major industrial center, its large population, and its proximity to major earthquake faults are important considerations with respect to earthquake hazards and water-resource management. The fault-bounded alluvial aquifer system beneath the valley is the source of about one-third of the water supply for the metropolitan area (Hanson et al., 2004). To better address the earthquake hazards of the SCV, the U.S. Geological Survey (USGS) has undertaken a program to evaluate potential seismic sources, the effects of strong ground shaking, and stratigraphy associated with the regional aquifer system. As part of that program and to better understand water resources of the valley, the USGS and the Santa Clara Valley Water District (SCVWD) began joint studies to characterize the faults, stratigraphy, and structures beneath the SCV in the year 2000. Such features are important to both agencies because they directly influence the availability and management of groundwater resources in the valley, and they affect the severity and distribution of strong shaking from local and regional earthquakes sources that may affect reservoirs, pipelines, and flood-protection facilities maintained by SCVWD. As one component of these joint studies, the USGS acquired an approximately 10-km-long, high-resolution, combined seismic reflection/refraction transect from the Santa Cruz Mountains to the central SCV in December 2000 (Figs. 1 and 2a,b). The overall seismic investigation of the western Santa Clara Valley also included an ~18-km-long, lower-resolution (~50-m sensor) seismic imaging survey from the central Santa Cruz Mountains to the central part of the valley (Fig. 1). Collectively, we refer to these seismic investigations as the 2000 western Santa Clara Seismic Investigations (SCSI). Results of the high-resolution investigation, referred to as SCSI-HR, are presented in this report, and Catchings et al. (2006) present results of the low-resolution investigation (SCSI-LR) in a separate report. In this report, we present data acquisition parameters, unprocessed and processed seismic data, and interpretations of the SCSI-HR seismic transect.

Miocene calc-alkaline magmatism, calderas, and crustal extension in the Kofa and Castle Dome Mountains, southwestern Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grubensky, M.J.; Bagby, W.C.

1990-11-10

Two widespread lower Miocene rhyolite ash flow tuffs in the Kofa and Castle Dome Mountains of southwestern Arizona are products of caldera-forming eruptions. These closely erupted tuffs, the tuff of Yaqui Tanks and the tuff of Ten Ewe Mountain, are approximately 22 Ma in age and their eruptions culminate a 1- to 2-m.y.-long burst of calc-alkaline volcanic activity centered on the northern Castle Dome Mountains. Exotic blocks of Proterozoic and Mesozoic crystalline rocks up to 20 m across are present in exposures of the tuff of Yaqui Tanks exposed in the central Castle Dome Mountains and the southern Kofa Mountains.more » A single, thick cooling unit of the tuff of Ten Ewe Mountain that includes thick lenses of mesobreccia marks the location of the younger caldera that extends from Palm Canyon in the western Kofa Mountains eastward more than 7 km along strike to the central part of the range. Large residual Bouguer gravity anomalies, one beneath each inferred caldera, are interpreted as batholithic rocks or low-density caldera fill. Caldera-related volcanism in the Kofa region occurred during a transition in extensional tectonic regimes: From a regime of east-west trending uplifts and basins to a regime manifest primarily by northwest striking normal faults. A narrow corridor of folding and strike-slip faulting formed during volcanism in the southern Kofa Mountains. Upper Oligocene or lower Miocene coarse sedimentary rocks along the southern flank of the Chocolate Mountains anticlinorium in the southern Castle Dome Mountains mark the periphery of a basin similar to other early and middle Tertiary basins exposed in southern California. The volcanic section of the Kofa region was dissected by high-angle normal faults related to northeast-southwest oriented crustal extension typical of the southern Basin and Range province.« less

Active faults system and related potential seismic events near Ulaanbaatar, capital of Mongolia.

NASA Astrophysics Data System (ADS)

Schlupp, Antoine; Ferry, Matthieu; Munkhuu, Ulziibat; Sodnomsambuu, Demberel; Al-Ashkar, Abeer

2013-04-01

The region of Ulaanbaatar lies several hundred kilometers from large known active faults that produced magnitude 6 to 8+ earthquakes during the last century. Beside the Hustai fault, which displays a clear morphological expression, no active fault was previously described less than 100 km from the city. In addition, no large historical (i.e. more recent than the 16th c.) earthquakes are known in this region. However, since 2005 a very dense seismic activity has developed over the Emeelt Township area, a mere 10 km from Ulaanbaatar. The activity is characterized by numerous low magnitude events (M<2.8), which are distributed linearly along several tens of kilometers where no active fault has been identified. This raises several questions: Is this seismicity associated to a -yet- unknown active fault? If so, are there other unknown active faults near Ulaanbaatar? Hence, we deployed a multi-disciplinary approach including morpho-tectonic, near-surface geophysical and paleoseismological investigations. We describe four large active faults west and south of Ulaanbaatar, three of them are newly discovered (Emeelt, Sharai, Avdar), one was previously known (Hustai) but without precise study on its seismic potential. The Emeelt seismicity can be mapped over 35 km along N150 and corresponds in the field to a smoothed, but clear, active fault morphology that can be mapped along a 10-km-long section. The fault dips at ~30° NE (GPR and surface morphology observations) and uplifts the eastern block. The age of the last surface rupture observed in trenches is about 10 ka (preliminary OSL dating). Considering a rupture length of 35 km, a full segment rupture would be comparable to the 1967 Mogod earthquake with a magnitude as large as Mw 7. It has to be considered today as a possible scenario for the seismic risk of Ulaanbaatar. The 90-km-long Hustai Range Fault System, oriented WSW-ENE and located about 10 km west of Ulaanbaatar, displays continuous microseismicity with five light to moderate (M 4 - 5.4) earthquakes over the last 40 years. The last surface-rupturing earthquake occurred about 1000 years ago (OSL dating). Alluvial fans affected by the fault suggest the rate of deformation (left lateral with normal component) along the main segment ranges from 0.3 to 0.4 mm/year for the last 120 000 years. Hence, the average recurrence interval for a full-segment M 7-7.5 is likely in the order of 10 ky. However, if the Hustai fault also releases strain during partial ruptures along its strongly segmented trace, a Mw 6.5 event may be expected anytime. However, only the main central fault segment has been investigated in terms of paleoseismicity. The Sharai and Avdar faults, oriented NNE-SSW, were mapped along ~50-km-long sections. Each of these faults was the site of earthquakes of magnitude 6 and more in the past as suggested by morphology and trench observations. Full-segment-ruptures could produce events as large as M 7.2. The precise relationship and interactions between these faults as well as associated earthquakes have to be clarified by collecting more data. They are the key of the seismic hazard and risk of Ulaanbaatar.

New Geologic Data on the Seismic Risks of the Most Dangerous Fault on Shore in Central Japan, the Itoigawa-Shizuoka Tectonic Line Active Fault System

NASA Astrophysics Data System (ADS)

Okumura, K.; Kondo, H.; Toda, S.; Takada, K.; Kinoshita, H.

2006-12-01

Ten years have past since the first official assessment of the long-term seismic risks of the Itoigawa-Shizuoka tectonic line active fault system (ISTL) in 1996. The disaster caused by the1995 Kobe (Hyogo-ken-Nanbu) earthquake urged the Japanese government to initiated a national project to assess the long-term seismic risks of on-shore active faults using geologic information. ISTL was the first target of the 98 significant faults and the probability of a M7 to M8 event turned out to be the highest among them. After the 10 years of continued efforts to understand the ISTL, now it is getting ready to revise the assessment. Fault mapping and segmentation: The most active segment of the Gofukuji fault (~1 cm/yr left-lateral strike slip, R=500~800 yrs.) had been maped only for less than 10 km. Adjacent segments were much less active. This large slip on such a short segment was contradictory. However, detailed topographic study including Lidar survey revealed the length of the Gofukuji fault to be 25 km or more. High slip rate with frequent earthquakes may be restricted to the Gofukuji fault while the 1996 assessment modeled frequent >100 km rupture scenario. The geometry of the fault is controversial especially on the left-lateral strike-slip section of the ISTL. There are two models of high-angle Middel ISTL and low-angle Middle ISTL with slip partitioning. However, all geomorphic and shallow geologic data supports high-angle almost pure strike slip on the faults in the Middle ISTL. CRIEPI's 3- dimensional trenching in several sites as well as the previous results clearly demonstrated repeated pure strike-slip offset during past a few events. In Middle ISTL, there is no evidence of recent activity of pre-existing low-angle thrust faults that are inferred to be active from shallow seismic survey. Separation of high (~3000 m) mountain ranges and low (<1000 m) basin floor requires significant dip-slip component, but basin-fill sediments and geology of the range do not need vertical separation along the Gofukuji fault. The key issue for the time-dependent assessment of the Northern ISTL (east dipping reverse faults) was the lack of reliable time constraints on past earthquakes. In order to solve this problem, we have carried out intensive geoslicer and boring survey of buried faults at Kisaki. Along a 35 m long transect, we collected total 150 m complete cores in 9 geoslicer and 5 all-core boring holes. This is one of the most intensive surveys of a buried fault scarp under the water table. About 20 m vertical offset of 6000-year-old buried A-horizon is now underlain by a series of flood deposits, point bars and over-bank sediments, that intercalates 2 or 3 faulting events. The precise timing and offset of each event recorded in the section will be the critical evidence to tell the synchroneity of earthquakes in the Northern ISTL and the Middle ISTL. The magnitude of the coming event on ISTL is the most important but uncertain parameter of the 1996 assessment. The structural and paleoseimological information will present better constraints on the earthquake.

Thermochronologic constraints on post-Paleozoic tectonic evolution of the central Transantarctic Mountains, Antarctica

NASA Astrophysics Data System (ADS)

Fitzgerald, Paul G.

1994-08-01

Built upon the roots of a compressive orogenic belt of late Proterozoic-early Paleozoic age and once adjacent to North America, the present-day Transantarctic Mountains (TAM) represent a rift flank, resulting from episodic uplift in the Cretaceous and Cenozoic. Fault blocks are discernible in present-day topography and subglacial morphology. Fission track results give information on differential block movement (uplift and denudation) and are important in constraining models for the uplift of the range. Apatite fission track thermochronology on samples collected from the central TAM record a complex thermotectonic history for this region over the past 350 m.y. Apatite ages in the Miller Range vary from ˜250 to ˜350 Ma and are from an exhumed apatite partial annealing zone formed following cooling of Cambro-Ordovician granitoids. A period of Cretaceous denudation (≲2 km), beginning at ˜115 Ma, is recorded at Moody Nunatak on the inland side of the TAM. Near the coast, samples along the Beardmore Glacier record rapid cooling indicative of denudation initiated in the early Cenozoic (˜50 Ma). The amount of uplift ˜70 km inland of the coast in the Queen Alexandra Range since the early Cenozoic is ˜7 km, with the likelihood of an additional ˜3 km at the coast. Eastward facing topographic escarpments in the Queen Alexandra Range mark the likely position of steeply dipping normal faults, which offset the apatite ages. Apatite ages on the east side of the Beardmore Glacier mouth are generally younger (average 27 Ma) than on the west side (average 33 Ma), reflecting greater denudation. Assumptions made regarding the use of an assumed paleogeothermal gradient are tested with available geologic evidence. The fission track data neither conflict with nor confirm paleobotanical evidence from the Sirius Group in the central TAM which suggests significant surface uplift (2-3 km) of the TAM since the Pliocene. Results build upon the available fission track database along the TAM and emphasize the subtle variability of uplift along the TAM due to episodic uplift involving differential block movements.

Spatiotemporal Patterns of Fault Slip Rates Across the Central Sierra Nevada Frontal Fault Zone

NASA Astrophysics Data System (ADS)

Rood, D. H.; Burbank, D.; Finkel, R. C.

2010-12-01

We examine patterns in fault slip rates through time and space across the transition from the Sierra Nevada to the Eastern California Shear Zone-Walker Lane belt. At each of four sites along the eastern Sierra Nevada frontal fault zone between 38-39° N latitude, geomorphic markers, such as glacial moraines and outwash terraces, are displaced by a suite of range-front normal faults. Using geomorphic mapping, surveying, and Be-10 surface exposure dating, we define mean fault slip rates, and by utilizing markers of different ages (generally, ~20 ka and ~150 ka), we examine rates through time and interactions among multiple faults over 10-100 ky timescales. At each site for which data are available for the last ~150 ky, mean slip rates across the Sierra Nevada frontal fault zone have probably not varied by more than a factor of two over time spans equal to half of the total time interval (~20 ky and ~150 ky timescales): 0.3 ± 0.1 mm/yr (mode and 95% CI) at both Buckeye Creek in the Bridgeport basin and Sonora Junction; and 0.4 +0.3/-0.1 mm/yr along the West Fork of the Carson River at Woodfords. Our data permit that rates are relatively constant over the time scales examined. In contrast, slip rates are highly variable in space over the last ~20 ky. Slip rates decrease by a factor of 3-5 northward over a distance of ~20 km between the northern Mono Basin (1.3 +0.6/-0.3 mm/yr at Lundy Canyon site) and the Bridgeport Basin (0.3 ± 0.1 mm/yr). The 3-fold decrease in the slip rate on the Sierra Nevada frontal fault zone northward from Mono Basin reflects a change in the character of faulting north of the Mina Deflection as extension is transferred eastward onto normal faults between the Sierra Nevada and Walker Lane belt. A compilation of regional deformation rates reveal that the spatial pattern of extension rates changes along strike of the Eastern California Shear Zone-Walker Lane belt. South of the Mina Deflection, extension is accommodated within a diffuse zone of normal and oblique faults, with extension rates increasing northward on the Fish Lake Valley fault. Where faults of the Eastern California Shear Zone terminate northward into the Mina Deflection, extension rates increase northward along the Sierra Nevada frontal fault zone to ~0.7 mm/yr in northern Mono Basin. This spatial pattern suggests that extension is transferred from faults systems to the east (e.g. Fish Lake Valley fault) and localized on the Sierra Nevada frontal fault zone as Eastern California Shear Zone-Walker Lane belt faulting is transferred through the Mina Deflection.

Revision of middle Proterozoic Yellowjacket Formation, central Idaho, and revision of Cretaceous Slim Sam Formation, Elkhorn mountains area, Montana

USGS Publications Warehouse

Tysdal, Russell G.

2000-01-01

The Yellowjacket Formation is restricted to the strata originally assigned to it by Ross (1934). The Yellowjacket, the conformably overlying Hoodoo Quartzite, and succeeding unnamed argillaceous quartzite unit form a genetically related sequence that lies in a structural block delimited on the northeast by the Iron Lake fault. Directly northeast of the fault, strata currently assigned by others to the lower subunit of the Yellowjacket are correlated with the Apple Creek Formation in the Lemhi Range. Mapping in the western part of the Lemhi Range shows that the Apple Creek Formation lies depositionally above the Big Creek Formation and that no rocks of the Yellowjacket-Hoodoo unnamed unit stratigraphic sequence are present. In contrast, in the area of the Yellowjacket mapped by Ross (1934) and the area directly northeast of the Iron Lake Fault, the Big Creek Formation is absent, even though it is 2,700 m thick in the Lemhi Range. These data indicate that the Iron Lake Fault juxtaposed the Yellowjacket-Hoodoo-unnamed unit sequence against non-Yellowjacket strata to the northeast. The Upper Cretaceous Slim Sam Formation of the Elkhorn Mountains area is revised. Strata of the lower part are correlated with the regionally recognized marine Telegraph Creek Formation and the overlying marine to marginal marine Eagle Sandstone. Only lower strata of the Eagle are present in the study area and they are preserved discontinously. The nonmarine volcanic and volcaniclastic rocks of the upper part of the Slim Sam as originally defined retain the name Slim Sam Formation. These rocks, mainly of sedimentary origin, are genetically related to the Elkhorn Mountains Volcanics. The lower contact of the Slim Sam (restricted) is unconformable above the Eagle Sandstone or more commonly above the Telegraph Creek Formation. The upper contact is conformable with the Elkhorn Mountains Volcanics.

Quantifying Late Quaternary Deformation along the Santa Ynez River, Santa Maria Basin, California

NASA Astrophysics Data System (ADS)

Slatten, C. L.; Onderdonk, N.

2017-12-01

The fault bounded Santa Maria Basin, located on the Central Coast of California, is positioned in an area of convergence between the rotating Western Transverse Ranges and the non-rotated Southern Coast Ranges. The Santa Ynez River Fault (SYRF) is an east-west trending fault that parallels the Santa Ynez River west of Lake Cachuma, California and defines the southern structural boundary of the Santa Maria Basin. However, the rate and style of Late Quaternary deformation and uplift in this region and the potential for seismic hazard along the fault is lacking. Fluvial terraces are key geomorphological components of fluvial systems that can be used to provide insights into regional and local uplift and deformation. The Santa Ynez River delineates the northern edge of the Santa Ynez Mountains and flows west through the Santa Ynez Valley to its mouth at the Pacific Ocean. The Santa Ynez River Field Area is a 10 km stretch of the Santa Ynez River just west of Lake Cachuma where terraces are well developed and the SYRF cuts through terraces and the active river (Figure 1). If there has been Quaternary movement of the SYRF we expect to find deformation in these areas. An initial survey of the area identified five terrace levels ranging from 8 m to 135 m above modern river level. The fluvial terraces are being mapped as separate units, surveyed for deformation with GPS based transects, and sampled for optically stimulated luminescence (OSL) dating. These combined methods will allow us to document the geomorphic characteristics and landform evolution of the lower Santa Ynez River, evaluate the possibility of Late Quaternary activity of the SYRF, and determine the rate of Late Quaternary regional uplift along the western Santa Ynez River in the Santa Maria Basin providing a possible basis for augmentation of the seismic hazards for Santa Barbara County.

Use of microearthquakes in the study of the mechanics of earthquake generation along the San Andreas fault in central California

USGS Publications Warehouse

Eaton, J.P.; Lee, W.H.K.; Pakiser, L.C.

1970-01-01

A small, dense network of independently recording portable seismograph stations was used to delineate the slip surface associated with the 1966 Parkfield-Cholame earthquake by precise three dimensional mapping of the hypocenters of its aftershocks. The aftershocks were concentrated in a very narrow vertical zone beneath or immediately adjacent to the zone of surf ace fracturing that accompanied the main shock. Focal depths ranged from less than 1 km to a maximum of 15 km. The same type of portable network was used to study microearthquakes associated with an actively creeping section of the San Andreas fault south of Hollister during the summer of 1967. Microearthquake activity during the 6-week operation of this network was dominated by aftershocks of a magnitude-4 earthquake that occurred within the network near Bear Valley on July 23. Most of the aftershocks were concentrated in an equidimensional region about 2 1 2km across that contained the hypocenter of the main shock. The zone of the concentrated aftershocks was centered near the middle of the rift zone at a depth of about 3 1 2km. Hypocenters of other aftershocks outlined a 25 km long zone of activity beneath the actively creeping strand of the fault and extending from the surface to a depth of about 13 km. A continuing study of microearthquakes along the San Andreas, Hayward, and Calaveras faults between Hollister and San Francisco has been under way for about 2 years. The permanent telemetered network constructed for this purpose has grown from about 30 stations in early 1968 to about 45 stations in late 1969. Microearthquakes between Hollister and San Francisco are heavily concentrated in narrow, nearly vertical zones along sections of the Sargent, San Andreas, and Calaveras faults. Focal depths range from less than 1 km to about 14 km. ?? 1970.

The new Central American seismic hazard zonation: Mutual consensus based on up to day seismotectonic framework

NASA Astrophysics Data System (ADS)

Alvarado, Guillermo E.; Benito, Belén; Staller, Alejandra; Climent, Álvaro; Camacho, Eduardo; Rojas, Wilfredo; Marroquín, Griselda; Molina, Enrique; Talavera, J. Emilio; Martínez-Cuevas, Sandra; Lindholm, Conrad

2017-11-01

Central America is one of the most active seismic zones in the World, due to the interaction of five tectonic plates (North America, Caribbean, Coco, Nazca and South America), and its internal deformation, which generates almost one destructive earthquakes (5.4 ≤ Mw ≤ 8.1) every year. A new seismological zonation for Central America is proposed based on seismotectonic framework, a geological context (tectonic and geological maps), geophysical and geodetic evidence (gravimetric maps, magnetometric, GPS observations), and previous works. As a main source of data a depurated earthquake catalog was collected covering the period from 1522 to 2015. This catalog was homogenized to a moment magnitude scale (Mw). After a careful analysis of all the integrated geological and seismological information, the seismogenic zones were established into seismic areas defined by similar patterns of faulting, seismicity, and rupture mechanism. The tectonic environment has required considering seismic zones in two particular seismological regimes: a) crustal faulting (including local faults, major fracture zones of plate boundary limits, and thrust fault of deformed belts) and b) subduction, taking into account the change in the subduction angle along the trench, and the type and location of the rupture. The seismicity in the subduction zone is divided into interplate and intraplate inslab seismicity. The regional seismic zonation proposed for the whole of Central America, include local seismic zonations, avoiding discontinuities at the national boundaries, because of a consensus between the 7 countries, based on the cooperative work of specialists on Central American seismotectonics and related topics.

Climatic and Tectonic Controls on Topography in the Northern Basin and Range

NASA Astrophysics Data System (ADS)

Foster, D.; Brocklehurst, S. H.; Gawthorpe, R. L.

2006-12-01

This study takes advantage of the relatively simple tectonics of the normal fault-bounded Lost River and Lemhi Ranges and the Beaverhead Mountains, eastern Idaho, USA, to assess the roles of climate, erosion, and tectonics in topographic evolution through a combination of digital topographic analyses and field observations. These ranges transect the southern limit of Quaternary glaciation, and drainage basins record a range of glacial extents and histories, allowing for comparisons between climatic and tectonic controls. At a catchment scale, topography is controlled by both the degree of glaciation, and the response of the drainage system to range-front faulting. The range-bounding normal faults are segmented along-strike, and fault uplift rates vary systematically, being greatest at the fault centres. Here catchments predominantly drain normal to the range-front fault, although the trend of some catchments is influenced by pre-existing tectonic fabrics related to Cretaceous (northeast-southwest trending) and early Miocene (northwest-southeast trending) extension. For catchments that drain through fault segment boundaries, one of two general morphologies occurs. Either large drainage basins form, capturing drainage area from neighbouring basins, or, when fault segment boundaries are en echelon, a series of small drainage basins may form as catchments as the inboard- and outboard- footwalls interact and respond to fault linkage. Quaternary glaciation affected all but the southern portions of each of the ranges, most extensively at the north-eastern range flank. Increased extent of glaciation within a catchment results in wider valley floors, steeper valley walls, and greater relief at elevations close to the ELA. Cirque formation occurs preferentially on the north-eastern range flank, where glaciers are sheltered from both solar radiation and snow re-distribution by the prevailing winds. Snow accumulation is promoted in this setting by the increased influx of wind-blown snow from the western side of the range crest, and large moraines extend beyond the eastern range front. For portions of the ranges affected by glaciation, range mean heights decrease along-strike by 1-2m per km to the north-west, similar to the rate of decrease in ELA and in the trend of cirque floor elevations. This suggests that a glacial "buzzsaw" effect controls the range mean heights.

Neogene contraction between the San Andreas fault and the Santa Clara Valley, San Francisco Bay region, California

USGS Publications Warehouse

McLaughlin, R.J.; Langenheim, V.E.; Schmidt, K.M.; Jachens, R.C.; Stanley, R.G.; Jayko, A.S.; McDougall, K.A.; Tinsley, J.C.; Valin, Z.C.

1999-01-01

In the southern San Francisco Bay region of California, oblique dextral reverse faults that verge northeastward from the San Andreas fault experienced triggered slip during the 1989 M7.1 Loma Prieta earthquake. The role of these range-front thrusts in the evolution of the San Andreas fault system and the future seismic hazard that they may pose to the urban Santa Clara Valley are poorly understood. Based on recent geologic mapping and geophysical investigations, we propose that the range-front thrust system evolved in conjunction with development of the San Andreas fault system. In the early Miocene, the region was dominated by a system of northwestwardly propagating, basin-bounding, transtensional faults. Beginning as early as middle Miocene time, however, the transtensional faulting was superseded by transpressional NE-stepping thrust and reverse faults of the range-front thrust system. Age constraints on the thrust faults indicate that the locus of contraction has focused on the Monte Vista, Shannon, and Berrocal faults since about 4.8 Ma. Fault slip and fold reconstructions suggest that crustal shortening between the San Andreas fault and the Santa Clara Valley within this time frame is ~21%, amounting to as much as 3.2 km at a rate of 0.6 mm/yr. Rates probably have not remained constant; average rates appear to have been much lower in the past few 100 ka. The distribution of coseismic surface contraction during the Loma Prieta earthquake, active seismicity, late Pleistocene to Holocene fluvial terrace warping, and geodetic data further suggest that the active range-front thrust system includes blind thrusts. Critical unresolved issues include information on the near-surface locations of buried thrusts, the timing of recent thrust earthquake events, and their recurrence in relation to earthquakes on the San Andreas fault.

Effects of Faults on Petroleum Fluid Dynamics, Borderland Basins of Southern California

NASA Astrophysics Data System (ADS)

Jung, B.; Garven, G.; Boles, J. R.

2012-12-01

Multiphase flow modeling provides a useful quantitative tool for understanding crustal processes such as petroleum migration in geological systems, and also for characterizing subsurface environmental issues such as carbon sequestration in sedimentary basins. However, accurate modeling of multi-fluid behavior is often difficult because of the various coupled and nonlinear physics affecting multiphase fluid saturation and migration, including effects of capillarity and relative permeability, anisotropy and heterogeneity of the medium, and the effects of pore pressure, composition, and temperature on fluid properties. Regional fault structures also play a strong role in controlling fluid pathlines and mobility, so considering hydrogeologic effects of these structures is critical for testing exploration concepts, and for predicting the fate of injected fluids. To address these issues on spatially large and long temporal scales, we have developed a 2-D multiphase fluid flow model, coupled to heat flow, using a hybrid finite element and finite volume method. We have had good success in applying the multiphase flow model to fundamental issues of long-distance petroleum migration and accumulation in the Los Angeles basin, which is intensely faulted and disturbed by transpressional tectonic stresses, and host to the world's richest oil accumulation. To constrain the model, known subsurface geology and fault structures were rendered using geophysical logs from industry exploration boreholes and published seismic profiles. Plausible multiphase model parameters were estimated, either from known fault permeability measurements in similar strata in the Santa Barbara basin, and from known formation properties obtained from numerous oil fields in the Los Angeles basin. Our simulations show that a combination of continuous hydrocarbon generation and primary migration from upper Miocene source rocks in the central LA basin synclinal region, coupled with a subsiding basin fluid dynamics, favored the massive accumulation and alignment of hydrocarbon pools along the Newport-Inglewood fault zone (NIFZ). According to our multiphase flow calculations, the maximum formation water velocities within fault zones likely ranged between 1 ~ 2 m/yr during the middle Miocene to Pliocene (13 to 2.6 Ma). The estimated time for long-distance (~ 25 km) petroleum migration from source beds in the central basin to oil fields along the NIFZ is approximately 150,000 ~ 250,000 years, depending on the effective permeability assigned to the faults and adjacent interbedded sandstone and siltstone "petroleum aquifers". With an average long-distance flow rate (~ 0.6 m/yr) and fault permeability of 100 millidarcys (10-13 m2), the total petroleum oil of Inglewood oil field of 450 million barrels (~ 1.6 × 105 m3) would have accumulated rather quickly, likely over 25,000 years or less. The results also suggest that besides the thermal and structural history of the basin, the fault permeability, capillary pressure, and the configuration of aquifer and aquitard layers played an important role in controlling petroleum migration rates, patterns of flow, and the overall fluid mechanics of petroleum accumulation.

Three-Dimensional Geologic Model of Complex Fault Structures in the Upper Seco Creek Area, Medina and Uvalde Counties, South-Central Texas

USGS Publications Warehouse

Pantea, Michael P.; Cole, James C.; Smith, Bruce D.; Faith, Jason R.; Blome, Charles D.; Smith, David V.

2008-01-01

This multimedia report shows and describes digital three-dimensional faulted geologic surfaces and volumes of the lithologic units of the Edwards aquifer in the upper Seco Creek area of Medina and Uvalde Counties in south-central Texas. This geologic framework model was produced using (1) geologic maps and interpretations of depositional environments and paleogeography; (2) lithologic descriptions, interpretations, and geophysical logs from 31 drill holes; (3) rock core and detailed lithologic descriptions from one drill hole; (4) helicopter electromagnetic geophysical data; and (5) known major and minor faults in the study area. These faults were used because of their individual and collective effects on the continuity of the aquifer-forming units in the Edwards Group. Data and information were compared and validated with each other and reflect the complex relationships of structures in the Seco Creek area of the Balcones fault zone. This geologic framework model can be used as a tool to visually explore and study geologic structures within the Seco Creek area of the Balcones fault zone and to show the connectivity of hydrologic units of high and low permeability between and across faults. The software can be used to display other data and information, such as drill-hole data, on this geologic framework model in three-dimensional space.

Gravity and magnetic investigations of the Ghost Dance and Solitario Canyon faults, Yucca Mountain, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ponce, D.A.; Langenheim, V.E.

1995-12-31

Ground magnetic and gravity data collected along traverses across the Ghost Dance and Solitario Canyon faults on the eastern and western flanks, respectively, of Yucca Mountain in southwest Nevada are interpreted. These data were collected as part of an effort to evaluate faulting in the vicinity of a potential nuclear waste repository at Yucca Mountain. Gravity and magnetic data and models along traverses across the Ghost Dance and Solitario Canyon faults show prominent anomalies associated with known faults and reveal a number of possible concealed faults beneath the eastern flank of Yucca Mountain. The central part of the eastern flankmore » of Yucca Mountain is characterized by several small amplitude anomalies that probably reflect small scale faulting.« less

Progressive failure during the 1596 Keicho earthquakes on the Median Tectonic Line active fault zone, southwest Japan

NASA Astrophysics Data System (ADS)

Ikeda, M.; Toda, S.; Nishizaka, N.; Onishi, K.; Suzuki, S.

2015-12-01

Rupture patterns of a long fault system are controlled by spatial heterogeneity of fault strength and stress associated with geometrical characteristics and stress perturbation history. Mechanical process for sequential ruptures and multiple simultaneous ruptures, one of the characteristics of a long fault such as the North Anatolian fault, governs the size and frequency of large earthquakes. Here we introduce one of the cases in southwest Japan and explore what controls rupture initiation, sequential ruptures and fault branching on a long fault system. The Median Tectonic Line active fault zone　(hereinafter MTL) is the longest and most active fault in Japan. Based on historical accounts, a series of M ≥ 7 earthquakes occurred on at least a 300-km-long portion of the MTL in 1596. On September 1, the first event occurred on the Kawakami fault segment, in Central Shikoku, and the subsequent events occurred further west. Then on September 5, another rupture initiated from the Central to East Shikoku and then propagated toward the Rokko-Awaji fault zone to Kobe, a northern branch of the MTL, instead of the eastern main extent of the MTL. Another rupture eventually extended to near Kyoto. To reproduce this progressive failure, we applied two numerical models: one is a coulomb stress transfer; the other is a slip-tendency analysis under the tectonic stress. We found that Coulomb stress imparted from historical ruptures have triggered the subsequent ruptures nearby. However, stress transfer does not explain beginning of the sequence and rupture directivities. Instead, calculated slip-tendency values show highly variable along the MTL: high and low seismic potential in West and East Shikoku. The initiation point of the 1596 progressive failure locates near the boundary in the slip-tendency values. Furthermore, the slip-tendency on the Rokko-Awaji fault zone is far higher than that of the MTL in Wakayama, which may explain the rupture directivity toward Kobe-Kyoto.

Limit on slip rate and timing of recent seismic ground-ruptures on the Jinghong fault, SE of the eastern Himalayan syntaxis

NASA Astrophysics Data System (ADS)

Shi, Xuhua; Weldon, Ray; Liu-Zeng, Jing; Wang, Yu; Weldon, Elise; Sieh, Kerry; Li, Zhigang; Zhang, Jinyu; Yao, Wenqian; Li, Zhanfei

2018-06-01

Quantifying slip rates and earthquake occurrence of active faults on the Shan Plateau, southeast of the eastern Himalayan syntaxis, is critical to assessing the seismic hazard and understanding the kinematics and geodynamics of this region. Most previous estimates of slip rates are averaged over either many millions of years using offset geological markers or decades using GPS. Well-constrained millennial slip rates of these faults remain sparse and constraints on recurrence rates of damaging earthquakes exist only for a few faults. Here we investigate the millennial slip rate and timing of recent earthquakes on the Jinghong fault, one of the geomorphically most significant sinistral-slip faults on the central Shan Plateau. We map and reconstruct fault offset (18 ± 5 m) of alluvial fan features at Manpa on the central Jinghong fault, using a 0.1 m-resolution digital surface model obtained from an unmanned aerial vehicle survey. We establish a slip rate, ≤2.5 ± 0.7 mm/yr over the past 7000 years, using pit-exposed stratigraphy. This millennial slip rate is consistent with rates averaged over both decadal and million-year timescales. Excavations at three sites near the town of Gelanghe on the northeastern Jinghong fault demonstrate 1) that the last seismic ground-rupture occurred between 482 and 889 cal yr BP, most likely in the narrower window 824-767 cal yr BP, if the lack of large earthquakes in the historical earthquake record is reliable, and 2) that multiple fault ruptures have occurred since 3618 cal yr BP. Combining this finding with a lack of large earthquakes in the 800-year-long Chinese historic record in this region, we suggest an average recurrence interval of seismic ground-ruptures on the order of 1000 years. This recurrence interval is consistent with the slip rate of the Jinghong fault and the size and earthquake frequency on other sinistral faults on the Shan Plateau.

Testing Pixel Translation Digital Elevation Models to Reconstruct Slip Histories: An Example from the Agua Blanca Fault, Baja California, Mexico

NASA Astrophysics Data System (ADS)

Wilson, J.; Wetmore, P. H.; Malservisi, R.; Ferwerda, B. P.; Teran, O.

2012-12-01

We use recently collected slip vector and total offset data from the Agua Blanca fault (ABF) to constrain a pixel translation digital elevation model (DEM) to reconstruct the slip history of this fault. This model was constructed using a Perl script that reads a DEM file (Easting, Northing, Elevation) and a configuration file with coordinates that define the boundary of each fault segment. A pixel translation vector is defined as a magnitude of lateral offset in an azimuthal direction. The program translates pixels north of the fault and prints their pre-faulting position to a new DEM file that can be gridded and displayed. This analysis, where multiple DEMs are created with different translation vectors, allows us to identify areas of transtension or transpression while seeing the topographic expression in these areas. The benefit of this technique, in contrast to a simple block model, is that the DEM gives us a valuable graphic which can be used to pose new research questions. We have found that many topographic features correlate across the fault, i.e. valleys and ridges, which likely have implications for the age of the ABF, long term landscape evolution rates, and potentially provide conformation for total slip assessments The ABF of northern Baja California, Mexico is an active, dextral strike slip fault that transfers Pacific-North American plate boundary strain out of the Gulf of California and around the "Big Bend" of the San Andreas Fault. Total displacement on the ABF in the central and eastern parts of the fault is 10 +/- 2 km based on offset Early-Cretaceous features such as terrane boundaries and intrusive bodies (plutons and dike swarms). Where the fault bifurcates to the west, the northern strand (northern Agua Blanca fault or NABF) is constrained to 7 +/- 1 km. We have not yet identified piercing points on the southern strand, the Santo Tomas fault (STF), but displacement is inferred to be ~4 km assuming that the sum of slip on the NABF and STF is approximately equal to that to the east. The ABF has varying kinematics along strike due to changes in trend of the fault with respect to the nearly east-trending displacement vector of the Ensenada Block to the north of the fault relative to a stable Baja Microplate to the south. These kinematics include nearly pure strike slip in the central portion of the ABF where the fault trends nearly E-W, and minor components of normal dip-slip motion on the NABF and eastern sections of the fault where the trends become more northerly. A pixel translation vector parallel to the trend of the ABF in the central segment (290 deg, 10.5 km) produces kinematics consistent with those described above. The block between the NABF and STF has a pixel translation vector parallel the STF (291 deg, 3.5 km). We find these vectors are consistent with the kinematic variability of the fault system and realign several major drainages and ridges across the fault. This suggests these features formed prior to faulting, and they yield preferred values of offset: 10.5 km on the ABF, 7 km on the NABF and 3.5 km on the STF. This model is consistent with the kinematic model proposed by Hamilton (1971) in which the ABF is a transform fault, linking extensional regions of Valle San Felipe and the Continental Borderlands.

Long-term deformation in the Mississippi Embayment (Central USA) imaged by high-resolution seismic reflection data

NASA Astrophysics Data System (ADS)

Hao, Yanjun

Large magnitude intraplate earthquakes are a puzzling exception to plate tectonic theory. Unlike earthquakes occurring along plate boundaries, large continental intraplate earthquakes are a rare occurrence and are often distributed over broad regions. Albeit rare, their occurrence can cause widespread damage because of the low attenuation of seismic energy typical of plate interiors [Hanks and Johnston, 1992]. In the Central USA, most of the recent tectonic intraplate seismicity concentrates along the New Madrid seismic zone (NMSZ), where three large (M>7) earthquakes occurred between 1811--1812 [Johnston and Schweig, 1996]. Here the low surface deformation rates [Calais and Stein, 2009] conflict with the elevated instrument-recorded seismicity and the occurrence of historical and prehistorical large magnitude events [Tuttle et al., 2002]. One of the promising hypotheses proposed to reconcile this apparent contradiction is that intraplate earthquakes may be temporally clustered, episodic or cyclic, and may migrate spatially at the regional or continental scale across multiple faults or fault systems. In order to test this hypothesis and to understand how and where the long-term deformation is accommodated in the Mississippi Embayment, Central USA, I utilize high-resolution seismic reflection data acquired by the Mississippi River Project [Magnani and McIntosh, 2009] and by a 2010 survey across the Meeman-Shelby fault [Magnani, 2011; Hao et al., 2013]. To identify the location of Quaternary deformation and characterize deformation history, I acquired, processed, and interpreted the seismic reflection data and integrated them with other available geophysical (e.g. seismicity, crustal and lithospheric models) and geological (e.g. magmatism and borehole) data. For my research, I focus on three regions in the Mississippi Embayment: 1) the Meeman-Shelby fault west of Memphis, Tennessee, 2) the eastern Reelfoot rift margin north of Memphis, Tennessee, and 3) the area in southeastern Arkansas along the Alabama-Oklahoma transform zone. Quaternary deformation and prolonged history of activity of the imaged faults is documented at all sites. The results show that Quaternary seismic activity in the Mississippi Embayment is accommodated by faults additional to the NMSZ fault system, and that fault activity is controlled by certain paleotectonic structures inherited from the Proterozoic and Paleozoic history of the North American continent. The identification of Quaternary seismogenic faults outside the footprint of the NMSZ and of the lower crustal anomaly (i.e. "rift pillow") supports seismotectonic models that predict deformation over a large area (e.g. Forte et al., 2007) and calls into questions in models that predict concentration of strain in the NMSZ region (e.g. Pollitz et al., 2001). A comparison between the newly imaged faults and the NMSZ faults shows that the former are indistinguishable from the latter except for the occurrence of instrumental seismicity. Based on the analysis of the location and sense of displacement of Quaternary deformation in the northern Mississippi Embayment, I propose a new fault network to reconcile the wide distribution of Quaternary faults with concentration of instrumental seismicity along the NMSZ. The fault network consists of three distinct trends of faults: ~N45°E right-lateral strike-slip faults, ~N20°W reverse faults, and ~N25°E right-lateral strike-slip faults. Different faults in the fault network appear to have been active at different times across the northern embayment. The available age data suggest a northward migration of the deformation, with the NMSZ representing the latest and youngest fault system.

Stress triggering in thrust and subduction earthquakes and stress interaction between the southern San Andreas and nearby thrust and strike-slip faults

USGS Publications Warehouse

Lin, J.; Stein, R.S.

2004-01-01

We argue that key features of thrust earthquake triggering, inhibition, and clustering can be explained by Coulomb stress changes, which we illustrate by a suite of representative models and by detailed examples. Whereas slip on surface-cutting thrust faults drops the stress in most of the adjacent crust, slip on blind thrust faults increases the stress on some nearby zones, particularly above the source fault. Blind thrusts can thus trigger slip on secondary faults at shallow depth and typically produce broadly distributed aftershocks. Short thrust ruptures are particularly efficient at triggering earthquakes of similar size on adjacent thrust faults. We calculate that during a progressive thrust sequence in central California the 1983 Mw = 6.7 Coalinga earthquake brought the subsequent 1983 Mw = 6.0 Nunez and 1985 Mw = 6.0 Kettleman Hills ruptures 10 bars and 1 bar closer to Coulomb failure. The idealized stress change calculations also reconcile the distribution of seismicity accompanying large subduction events, in agreement with findings of prior investigations. Subduction zone ruptures are calculated to promote normal faulting events in the outer rise and to promote thrust-faulting events on the periphery of the seismic rupture and its downdip extension. These features are evident in aftershocks of the 1957 Mw = 9.1 Aleutian and other large subduction earthquakes. We further examine stress changes on the rupture surface imparted by the 1960 Mw = 9.5 and 1995 Mw = 8.1 Chile earthquakes, for which detailed slip models are available. Calculated Coulomb stress increases of 2-20 bars correspond closely to sites of aftershocks and postseismic slip, whereas aftershocks are absent where the stress drops by more than 10 bars. We also argue that slip on major strike-slip systems modulates the stress acting on nearby thrust and strike-slip faults. We calculate that the 1857 Mw = 7.9 Fort Tejon earthquake on the San Andreas fault and subsequent interseismic slip brought the Coalinga fault ???1 bar closer to failure but inhibited failure elsewhere on the Coast Ranges thrust faults. The 1857 earthquake also promoted failure on the White Wolf reverse fault by 8 bars, which ruptured in the 1952 Mw = 7.3 Kern County shock but inhibited slip on the left-lateral Garlock fault, which has not ruptured since 1857. We thus contend that stress transfer exerts a control on the seismicity of thrust faults across a broad spectrum of spatial and temporal scales. Copyright 2004 by the American Geophysical Union.

Imaging 2D structures by the CSAMT method: application to the Pantano di S. Gregorio Magno faulted basin (Southern Italy)

NASA Astrophysics Data System (ADS)

Troiano, Antonio; Di Giuseppe, Maria Giulia; Petrillo, Zaccaria; Patella, Domenico

2009-06-01

A controlled source audiofrequency magnetotelluric (CSAMT) survey has been undertaken in the Pantano di San Gregorio Magno faulted basin, an earthquake prone area of Southern Apennines in Italy. A dataset from 11 soundings, distributed along a nearly N-S 780 m long profile, was acquired in the basin's easternmost area, where the fewest data are available as to the faulting shallow features. A preliminary skew analysis allowed a prevailing 2D nature of the dataset to be ascertained. Then, using a single-site multi-frequency approach, Dantzig's simplex algorithm was introduced for the first time to estimate the CSAMT decomposition parameters. The simplex algorithm, freely available online, proved to be fast and efficient. By this approach, the TM and TE mode field diagrams were obtained and a N35°W ± 10° 2D strike mean direction was estimated along the profile, in substantial agreement with the fault traces within the basin. A 2D inversion of the apparent resistivity and phase curves at seven almost noise-free sites distributed along the central portion of the profile was finally elaborated, reinforced by a sensitivity analysis, which allowed the best resolved portion of the model to be imaged from the first few meters of depth down to a mean depth of 300 m b.g.l. From the inverted section, the following features have been outlined: (i) a cover layer with resistivity in the range 3-30 Ω m ascribed to the Quaternary lacustrine clayey deposits filling the basin, down to an average depth of about 35 m b.g.l., underlain by a structure with resistivity over 50 Ω m up to about 600 Ω m, ascribed to the Mesozoic carbonate bedrock; (ii) a system of two normal faults within the carbonate basement, extending down to the maximum best resolved depth of the order of 300 m b.g.l.; (iii) two wedge-shaped domains separating the opposite blocks of the faults with resistivity ranging between 30 Ω m and 50 Ω m and horizontal extent of the order of some tens of metres, likely filled with lacustrine sediments and embedded fine gravels.

Estimating Earthquake Magnitude from the Kentucky Bend Scarp in the New Madrid Seismic Zone Using Field Geomorphic Mapping and High-Resolution LiDAR Topography

NASA Astrophysics Data System (ADS)

Kelson, K. I.; Kirkendall, W. G.

2014-12-01

Recent suggestions that the 1811-1812 earthquakes in the New Madrid Seismic Zone (NMSZ) ranged from M6.8-7.0 versus M8.0 have implications for seismic hazard estimation in the central US. We more accurately identify the location of the NW-striking, NE-facing Kentucky Bend scarp along the northern Reelfoot fault, which is spatially associated with the Lake County uplift, contemporary seismicity, and changes in the Mississippi River from the February 1812 earthquake. We use 1m-resolution LiDAR hillshades and slope surfaces, aerial photography, soil surveys, and field geomorphic mapping to estimate the location, pattern, and amount of late Holocene coseismic surface deformation. We define eight late Holocene to historic fluvial deposits, and delineate younger alluvia that are progressively inset into older deposits on the upthrown, western side of the fault. Some younger, clayey deposits indicate past ponding against the scarp, perhaps following surface deformational events. The Reelfoot fault is represented by sinuous breaks-in-slope cutting across these fluvial deposits, locally coinciding with shallow faults identified via seismic reflection data (Woolery et al., 1999). The deformation pattern is consistent with NE-directed reverse faulting along single or multiple SW-dipping fault planes, and the complex pattern of fluvial deposition appears partially controlled by intermittent uplift. Six localities contain scarps across correlative deposits and allow evaluation of cumulative surface deformation from LiDAR-derived topographic profiles. Displacements range from 3.4±0.2 m, to 2.2±0.2 m, 1.4±0.3 m, and 0.6±0.1 m across four progressively younger surfaces. The spatial distribution of the profiles argues against the differences being a result of along-strike uplift variability. We attribute the lesser displacements of progressively younger deposits to recurrent surface deformation, but do not yet interpret these initial data with respect to possible earthquake magnitudes. Additional efforts hopefully will address shallow subsurface evidence of single- or multiple-deformational events at selected localities.

Preliminary ground motion prediction equations for the Central and Eastern United States

NASA Astrophysics Data System (ADS)

Graizer, V.

2014-12-01

At the current stage I used the database created under the Next Generation Attenuations (NGA-East) project by Cramer et al. (2013). In contrast to the active tectonic environment in the Western US (WUS) the strong motion record database for the stable continental environment in the Central and Eastern US (CEUS) is not sufficient to create purely empirical ground motion prediction equations (GMPE) covering required for the PSHA magnitude (4.5

Correlation, sedimentology, structural setting, chemical composition, and provenance of selected formations in Mesoproterozoic Lemhi Group, central Idaho

USGS Publications Warehouse

Tysdal, Russell G.; Lindsey, David A.; Taggart, Joseph E.

2003-01-01

A unit of the Mesoproterozoic Apple Creek Formation of the Lemhi Range previously was correlated with part of the lower subunit of the Mesoproterozoic Yellowjacket Formation in the Salmon River Mountains. Strata currently assigned to the middle subunit of the Yellowjacket Formation lie conformably above the Apple Creek unit in the Salmon River Mountains, and are here renamed the banded siltite unit and reassigned to the Apple Creek Formation. Almost all of the banded siltite unit is preserved within the Salmon River Mountains, where it grades upward into clastic rocks that currently are assigned to the upper subunit of the Yellowjacket Formation and that here are reassigned to the Gunsight Formation. The banded siltite unit of the Apple Creek Formation is composed of a turbidite sequence, as recognized by previous workers. Uppermost strata of the unit were reworked by currents, possibly storm generated, and adjusted to a high water content by developing abundant soft-sediment deformation features. Basal strata of the overlying Gunsight Formation in the Salmon River Mountains display abundant hummocky crossbeds, storm-generated features deposited below fair-weather wave base, that are conformable above the storm-reworked deposits. The hummocky crossbedded strata grade upward into marine shoreface strata deposited above fair-weather wave base, which in turn are succeeded by fluvial strata. Hummocky and shoreface strata are absent from the Gunsight Formation in the Lemhi Range. The major thickness of the Gunsight Formation in both the Salmon River Mountains and the Lemhi Range is composed of fluvial rocks, transitional in the upper part into marine rocks of the Swauger Formation. The fluvial strata are mainly characterized by stacked sheets of metasandstone and coarse siltite; they are interpreted as deposits of braided rivers. The Poison Creek thrust fault of the Lemhi Range extends northwestward through the study area in the east-central part of the Salmon River Mountains. The Apple Creek and Gunsight Formations on the southwest side of the thrust fault were transported to the northeast as part of the Poison Creek thrust sheet. A segment of the thrust fault within the Gunsight Formation in the Salmon River Mountains subsequently underwent normal displacement. Along this segment, lower Gunsight strata on the southwest were juxtaposed against upper Gunsight and Swauger strata on the northeast.

The Gabbs Valley, Nevada, geothermal prospect: Exploring for a potential blind geothermal resource

NASA Astrophysics Data System (ADS)

Payne, J.; Bell, J. W.; Calvin, W. M.

2012-12-01

The Gabbs Valley prospect in west-central Nevada is a potential blind geothermal resource system. Possible structural controls on this system were investigated using high-resolution LiDAR, low sun-angle aerial (LSA) photography, exploratory fault trenching and a shallow temperature survey. Active Holocene faults have previously been identified at 37 geothermal systems with indication of temperatures greater than 100° C in the western Nevada region. Active fault controls in Gabbs Valley include both Holocene and historical structures. Two historical earthquakes occurring in 1932 and 1954 have overlapping surface rupture patterns in Gabbs Valley. Three active fault systems identified through LSA and LiDAR mapping have characteristics of Basin and Range normal faulting and Walker Lane oblique dextral faulting. The East Monte Cristo Mountains fault zone is an 8.5 km long continuous NNE striking, discrete fault with roughly 0.5 m right-normal historic motion and 3 m vertical Quaternary separation. The Phillips Wash fault zone is an 8.2 km long distributed fault system striking NE to N, with Quaternary fault scarps of 1-3 m vertical separation and a 500 m wide graben adjacent to the Cobble Cuesta anticline. This fault displays ponded drainages, an offset terrace riser and right stepping en echelon fault patterns suggestive of left lateral offset, and fault trenching exposed non-matching stratigraphy typical of a significant component of lateral offset. The unnamed faults of Gabbs Valley are a 10.6 km long system of normal faults striking NNE and Quaternary scarps are up to 4 m high. These normal faults largely do not have historic surface rupture, but a small segment of 1932 rupture has been identified. A shallow (2 m deep) temperature survey of 80 points covering roughly 65 square kilometers was completed. Data were collected over approximately 2 months, and continual base station temperature measurements were used to seasonally correct temperature measurements. A 2.5 km long temperature anomaly greater than 3° C above background temperatures forms west-northwest trending zone between terminations of the Phillips Wash fault zone and unnamed faults of Gabbs Valley to the south. Rupture segments of two young active faults bracket the temperature anomaly. The temperature anomaly may be due to several possible causes. 1. Increases in stress near the rupture segments or tip-lines of these faults, or where multiple fault splays exist, can increase fault permeability. The un-ruptured segments of these faults may be controlling the location of the Gabbs Valley thermal anomaly between ruptured segments of the 1932 Cedar Mountain and 1954 Fairview Peak earthquakes. 2. Numerous unnamed normal faults may interact and the hanging wall of these faults is hosting the thermal anomaly. The size and extent of the anomaly may be due to its proximity to a flat playa and not the direct location of the shallow heat anomaly. 3. The linear northwest nature of the thermal anomaly may reflect a hydrologic barrier in the subsurface controlling where heated fluids rise. A concealed NW- striking fault is possible, but has not been identified in previous studies or in the LiDAR or LSA fault mapping.

Deformational and erosional history for the Abiquiu and contiguous area, north-central New Mexico: Implications for formation of the Abiquiu embayment and a discussion of new geochronological and geochemical analysis

USGS Publications Warehouse

Maldonado, Florian; Miggins, Daniel P.; Budahm, James R.

2013-01-01

Geologic mapping, age determinations, and geochemistry of rocks exposed in the Abiquiu area of the Abiquiu embayment of the Rio Grande rift, north-central New Mexico, provide data to determine fault-slip and incision rates. Vertical-slip rates for faults in the area range from 16 m/m.y. to 42 m/m.y., and generally appear to decrease from the eastern edge of the Colorado Plateau to the Abiquiu embayment. Incision rates calculated for the period ca. 10 to ca. 3 Ma indicate rapid incision with rates that range from 139 m/m.y. on the eastern edge of the Colorado Plateau to 41 m/m.y. on the western part of the Abiquiu embayment.The Abiquiu area is located along the margin of the Colorado Plateau–Rio Grande rift and lies within the Abiquiu embayment, a shallow, early extensional basin of the Rio Grande rift. Cenozoic rocks include the Eocene El Rito Formation, Oligocene Ritito Conglomerate, Oligocene–Miocene Abiquiu Formation, and Miocene Chama–El Rito and Ojo Caliente Sandstone Members of the Tesuque Formation (Santa Fe Group). Volcanic rocks include the Lobato Basalt (Miocene; ca. 15–8 Ma), El Alto Basalt (Pliocene; ca. 3 Ma), and dacite of the Tschicoma Formation (Pliocene; ca. 2 Ma). Quaternary deposits consist of inset axial and side-stream deposits of the ancestral Rio Chama (Pleistocene in age), landslide and pediment alluvium and colluvium, and Holocene main and side-stream channel and floodplain deposits of the modern Rio Chama. The predominant faults are Tertiary normal high-angle faults that displace rocks basinward.A low-angle fault, referred to as the Abiquiu fault, locally separates an upper plate composed of the transitional zone of the Ojo Caliente Sandstone and Chama–El Rito Members from a lower plate consisting of the Abiquiu Formation or the Ritito Conglomerate. The upper plate is distended into blocks that range from about 0.1 km to 3.5 km long that may represent a larger sheet that has been broken up and partly eroded.Geochronology (40Ar/39Ar) from fifteen volcanic and intrusive rocks resolves discrete volcanic episodes in the Abiquiu area: (1) emplacement of Early and Late Miocene basaltic dikes at 20 Ma and ca. 10 Ma; (2) extensive Late Miocene–age lava flows at 9.5 Ma, 7.9 Ma, and 5.6 Ma; and (3) extensive basaltic eruptions during the early Pliocene at 2.9 Ma and 2.4 Ma. Clasts of biotite- and hornblende-rich trachyandesites and trachydacites from the base of the Abiquiu Formation are dated at ca. 27 Ma, possibly derived from the Latir volcanic field. The most-mafic magmas are interpreted to be generated from a similar lithospheric mantle during rifting, but variations in composition are correlated with partial melting at different depths, which is correlated with thinning of the crust due to extensional processes.

Subsurface Resistivity Structures in and Around Strike-Slip Faults - Electromagnetic Surveys and Drillings Across Active Faults in Central Japan -

NASA Astrophysics Data System (ADS)

Omura, K.; Ikeda, R.; Iio, Y.; Matsuda, T.

2005-12-01

Electrical resistivity is important property to investigate the structure of active faults. Pore fluid affect seriously the electrical properties of rocks, subsurface electrical resistivity can be an indicator of the existence of fluid and distribution of pores. Fracture zone of fault is expected to have low resistivity due to high porosity and small gain size. Especially, strike-slip type fault has nearly vertical fracture zone and the fracture zone would be detected by an electrical survey across the fault. We performed electromagnetic survey across the strike-slip active faults in central Japan. At the same faults, we also drilled borehole into the fault and did downhole logging in the borehole. We applied MT or CSAMT methods onto 5 faults: Nojima fault which appeared on the surface by the 1995 Great Kobe earthquake (M=7.2), western Nagano Ohtaki area(1984 Nagano-ken seibu earthquake (M=6.8), the fault did not appeared on the surface), Neodani fault which appeared by the 1891 Nobi earthquake (M=8.0), Atera fault which seemed to be dislocated by the 1586 Tensyo earthquake (M=7.9), Gofukuji fault that is considered to have activated about 1200 years ago. The sampling frequencies of electrical and magnetic field were 2 - 1024Hz (10 frequencies) for CSAMT survey and 0.00055 - 384Hz (40 frequencies) for MT survey. The electromagnetic data were processed by standard method and inverted to 2-D resistivity structure along transects of the faults. Results of the survey were compared with downhole electrical logging data and observational descriptions of drilled cores. Fault plane of each fault were recognized as low resistivity region or boundary between relatively low and high resistivity region, except for Gofukuji fault. As for Gofukuji fault, fault was located in relatively high resistivity region. During very long elapsed time from the last earthquake, the properties of fracture zone of Gofukuji fault might changed from low resistivity properties as observed for other faults. Downhole electrical logging data were consistent to values of resistivity estimated by electromagnetic survey for each fault. The existence of relatively low and high resistivity regions in 2-D structure from electromagnetic survey was observed again by downhole logging at the correspondent portion in the borehole. Cores recovered from depthes where the electrical logging showed low resistivity were hardly fractured and altered from host rock which showed high resistivity. Results of electromagnetic survey, downhole electrical logging and observation of drilled cores were consistent to each other. In present case, electromagnetic survey is useful to explore the properties of fault fracture zone. In the further investigations, it is important to explore relationships among features of resistivity structure and geological and geophysical situations of the faults.

Ground motion amplification at rock sites: the competing role of topography and fractured rocks in the San Giovanni fault, central Italy

NASA Astrophysics Data System (ADS)

Pischiutta, M.; Cara, F.; Di Giulio, G.; Vassallo, M.; Cultrera, G.

2017-12-01

Amplification at rock sites in areas of high topographic relief has been increasingly observed in the last years, with unexpected level of damage after strong earthquakes. In regions affected by recent tectonic activity, topographic irregularities can include fault damage zones. In such conditions, seismic waves can be locally amplified as a double effect of wave focusing along the topography and /or the presence of fractures/joints or locally weakened rocks. The role of topography vs. geological complexities in controlling the ground motion amplification at rock sites is a newly debated issue in the seismological community. The most crucial questions regard what is the real contribution of the topography shape and fracturing, and how to parameterize such effects for their inclusion in the seismic design codes. In this framework, the EMERSITO INGV task force installed 7 seismic stations across the San Giovanni fault, after the Amatrice mainshock of the 2016 sequence in Central Italy. This active normal fault is located in the area of the Montereale intermountain basin (Abruzzi region, Italy) and bounds the southwestern slope of Mt. Mozzano, a roughly 2D-shaped, up to 1450 m high pronounced topography. Moreover, this fault has been recently studied by several authors who performed detailed geological and geophysical surveys. Our stations recorded more than 100 earthquakes with magnitude ranging from 2.5 to 3.9 as well as a 4.4 M earthquake with hypocenter in Capitignano district, few kilometres far. We have analyzed in detail the recorded signals calculating the traditional spectral ratios at single station (HVSRs) and using the reference site (SSRs) using both ambient noise and earthquakes. In order to obtain a robust estimate of the site amplification effect at each station, we have investigated the influence of backazimuth and epicentral distance. We have also applied the time-domain covariance matrix analysis and the frequency domain polarization analysis. We have found that, in spite of the complexity of the seismic data, the observed polarization pattern is generally oriented orthogonal to the ridge elongation, as well as to the fault strike, suggesting the existence of a high angle relation between ground motion polarization and fracture systems.

Structural Controls of the Friction Constitutive Properties of Carbonate-bearing Faults

NASA Astrophysics Data System (ADS)

Carpenter, B. M.; Collettini, C.; Scuderi, M.; Marone, C.

2012-12-01

The identification of hetereogenous and complex post-seismic slip for the 2009, Mw = 6.3, L'Aquila earthquake highlights the importance of fault zone structure and frictional behavior. Many of the Mw 6 to 7 earthquakes that occur on normal faults in the active Apennines, such as L'Aquila, nucleate at depths where the lithology is dominated by carbonate rocks. Due to the complex structure observed in exhumed faults (i.e. the presence of highly polished principal slip surfaces, cemented cataclasites, and phyllosilicate-bearing, foliated fault gouge) as well as the large spectrum of fault slip behaviors identified world wide, we designed a suite of experiments using intact and powdered samples to better constrain the possible slip behaviors of these carbonate bearing faults. We collected samples from the exposed Rocchetta Fault, a ~10km long, normal fault with approximately 600m of total offset. The exposed principal slip surface cuts through the Calcare Massiccio formation, which is present throughout central Italy at depths of earthquake nucleation. We collected intact specimens of the natural slip surface and cemented cataclasite, as well as fragments of both which were later pulverized. Furthermore, we collected an intact sample of the hanging wall cataclasite and footwall limestone that contained the principal slip surface. We performed friction experiments in a variety of different configurations (slip surface on slip surface, slip surface on powdered cataclasite, etc.) in order to investigate heterogeneity in frictional behavior as controlled by fault structure. We sheared saturated samples at a constant normal stress of 10 MPa at room temperature. Velocity-stepping tests were performed from 1 to 300 μm/s to identify the friction constitutive parameters of this fault material. Furthermore, a series slide-hold-slide tests were performed (holds of 3 to 1000 seconds) to measure the amount of frictional healing and determine the frictional healing rate. Results from experiments designed to reactivate slip between the principal slip surface and cemented cataclasite show a peak friction value of ~0.95 followed by a ~3 MPa stress drop as the fault surface fails. Our other results suggest that earthquakes will easily nucleate in areas of the fault where two slip surfaces are in contact and are likely to propagate in areas where pulverized fault gouge is in contact with the slip surface. Our data show that samples collected from a single fault can exhibit a large range of slip behaviors. Heterogeneous frictional behavior documented in the lab must be combined with field observations of complex fault structure and seismological observations of the different modes of fault slip to further our understanding of fault slip. Future work will consist of thin section and XRD analysis of all experimental material.

The structures, stratigraphy and evolution of the Gulf of Corinth rift, Greece

NASA Astrophysics Data System (ADS)

Taylor, Brian; Weiss, Jonathan R.; Goodliffe, Andrew M.; Sachpazi, Maria; Laigle, Mireille; Hirn, Alfred

2011-06-01

A multichannel seismic and bathymetry survey of the central and eastern Gulf of Corinth (GoC), Greece, reveals the offshore fault geometry, seismic stratigraphy and basin evolution of one of Earths most active continental rift systems. Active, right-stepping, en-echelon, north-dipping border faults trend ESE along the southern Gulf margin, significantly overlapping along strike. The basement offsets of three (Akrata-Derveni, Sithas and Xylocastro) are linked. The faults are biplanar to listric: typically intermediate angle (˜35° in the centre and 45-48° in the east) near the surface but decreasing in dip and/or intersecting a low- or shallow-angle (15-20° in the centre and 19-30° in the east) curvi-planar reflector in the basement. Major S-dipping border faults were active along the northern margin of the central Gulf early in the rift history, and remain active in the western Gulf and in the subsidiary Gulf of Lechaio, but unlike the southern border faults, are without major footwall uplift. Much of the eastern rift has a classic half-graben architecture whereas the central rift has a more symmetric w- or u-shape. The narrower and shallower western Gulf that transects the >40-km-thick crust of the Hellenides is associated with a wider distribution of overlapping high-angle normal faults that were formerly active on the Peloponnesus Peninsula. The easternmost sector includes the subsidiary Gulfs of Lechaio and Alkyonides, with major faults and basement structures trending NE, E-W and NW. The basement faults that control the rift architecture formed early in the rift history, with little evidence (other than the Vrachonisida fault along the northern margin) in the marine data for plan view evolution by subsequent fault linkage. Several have maximum offsets near one end. Crestal collapse graben formed where the hanging wall has pulled off the steeper onto the shallower downdip segment of the Derveni Fault. The dominant strikes of the Corinth rift faults gradually rotate from 090-120° in the basement and early rift to 090-100° in the latest rift, reflecting a ˜10° rotation of the opening direction to the 005° presently measured by GPS. The sediments include a (locally >1.5-km-) thick, early-rift section, and a late-rift section (also locally >1.5-km-thick) that we subdivide into three sequences and correlate with seven 100-ka glacio-eustatic cycles. The Gulf depocentre has deepened through time (currently >700 mbsl) as subsidence has outpaced sedimentation. We measure the minimum total horizontal extension across the central and eastern Gulf as varying along strike between 4 and 10 km, and estimate full values of 6-11 km. The rift evolution is strongly influenced by the inherited basement fabric. The regional NNW structural fabric of the Hellenic nappes changes orientation to ESE in the Parnassos terrane, facilitating the focused north-south extension observed offshore there. The basement-penetrating faults lose seismic reflectivity above the 4-14-km-deep seismogenic zone. Multiple generations and dips of normal faults, some cross-cutting, accommodate extension beneath the GoC, including low-angle (15-20°) interfaces in the basement nappes. The thermally cool forearc setting and cross-orogen structures unaccompanied by magmatism make this rift a poor analogue and unlikely precursor for metamorphic core complex formation.

Shallow subsurface imaging of the Piano di Pezza active normal fault (central Italy) by high-resolution refraction and electrical resistivity tomography coupled with time domain electromagnetic data

NASA Astrophysics Data System (ADS)

Villani, Fabio; Tulliani, Valerio; Fierro, Elisa; Sapia, Vincenzo; Civico, Riccardo

2015-04-01

The Piano di Pezza fault is the north-westernmost segment of the >20 km long Ovindoli-Pezza active normal fault-system (central Italy). Although existing paleoseismic data document high vertical Holocene slip rates (~1 mm/yr) and a remarkable seismogenic potential of this fault, its subsurface setting and Pleistocene cumulative displacement are still poorly known. We investigated for the first time by means of high-resolution seismic and electrical resistivity tomography coupled with time domain electromagnetic (TDEM) measurements the shallow subsurface of a key section of the Piano di Pezza fault. Our surveys cross a ~5 m-high fault scarp that was generated by repeated surface-rupturing earthquakes displacing some Late Holocene alluvial fans. We provide 2-D Vp and resistivity images which clearly show significant details of the fault structure and the geometry of the shallow basin infill material down to 50 m depth. We can estimate the dip (~50°) and the Holocene vertical displacement of the master fault (~10 m). We also recognize in the hangingwall some low-velocity/low-resistivity regions that we relate to packages of colluvial wedges derived from scarp degradation, which may represent the record of several paleo-earthquakes older than the Late Holocene events previously recognized by paleoseismic trenching. Conversely, due to the limited investigation depth of seismic and electrical tomography, the estimation of the cumulative amount of Pleistocene throw is hampered. Therefore, to increase the depth of investigation, we performed 7 TDEM measurements along the electrical profile using a 50 m loop size both in central and offset configuration. The recovered 1-D resistivity models show a good match with 2-D resistivity images in the near surface. Moreover, TDEM inversion results indicate that in the hangingwall, ~200 m away from the surface fault trace, the carbonate pre-Quaternary basement may be found at ~90-100 m depth. The combined approach of electrical and seismic data coupled with TDEM measurements provides a robust constraint to the Piano di Pezza fault cumulative offset. Our data are useful for better reconstructing the deep structural setting of the Piano di Pezza basin and assessing the role played by extensional tectonics in its Quaternary evolution.

Central and eastern Anatolian crustal deformation rate and velocity fields derived from GPS and earthquake data

NASA Astrophysics Data System (ADS)

Simão, N. M.; Nalbant, S. S.; Sunbul, F.; Komec Mutlu, A.

2016-01-01

We present a new strain-rate and associated kinematic model for the eastern and central parts of Turkey. In the east, a quasi N-S compressional tectonic regime dominates the deformation field and is partitioned through the two major structural elements of the region, which are the conjugate dextral strike-slip North Anatolian Fault Zone (NAFZ) and the sinistral strike slip East Anatolian Fault Zone (EAFZ). The observed surface deformation is similar to that inferred by anisotropy studies which sampled the region of the mantle closer to the crust (i.e. the lithospheric mantle and the Moho), and is dependent on the presence or absence of a lithospheric mantle, and of the level of coupling between it and the overlaying crust. The areas of the central and eastern parts of Turkey which are deforming at elevated rates are situated above areas with strong gradients in crustal thickness. This seems to indicate that these transition zones, situated between thinner and thicker crusts, promote more deformation at the surface. The regions that reveal elevated strain-rate values are 1) the Elaziğ-Bingol segment of the EAFZ, 2) the region around the Karlıova triple-junction including the Yedisu segment and the Varto fault, 3) the section of the NAFZ that extends from the Erzincan province up to the NAFZ-Ezinepazarı fault junction, and 4) sections of the Tuz Gölü Fault Zone. Other regions like the Adana basin, a significant part of the Central Anatolian Fault Zone (CAFZ), the Aksaray and the Ankara provinces, are deforming at smaller but still considerable rates and therefore should be considered as areas well capable of producing damaging earthquakes (between M6 and 7). This study also reveals that the central part of Turkey is moving at a faster rate towards the west than the eastern part Turkey, and that the wedge region between the NAFZ and the EAFZ accounts for the majority of the counter clockwise rotation between the eastern and the central parts of Turkey. This change in movement rate and direction could be the cause of the extensional deformation and respective crustal thinning, with the resulting upwelling of warmer upper mantle observed in tomographic studies for the region between the Iskenderun bay and the CAFZ. The partitioning of deformation into an extensional regime could be the cause of the relatively low levels of strain-rate in the south-west part of the EAFZ and the northern part of the Dead Sea Fault Zone. Finally, using this new compilation of GPS data for the central-eastern part of Turkey, we obtained a new Anatolia-Eurasia rotation pole situated at 2.01°W and 31.94°N with a rotation rate of 1.053 ± 0.015° /Ma.

Late Cenozoic sedimentation and volcanism during transtensional deformation in Wingate Wash and the Owlshead Mountains, Death Valley

USGS Publications Warehouse

Luckow, H.G.; Pavlis, T.L.; Serpa, L.F.; Guest, B.; Wagner, D.L.; Snee, L.; Hensley, T.M.; Korjenkov, A.

2005-01-01

New 1:24,000 scale mapping, geochemical analyses of volcanic rocks, and Ar/Ar and tephrochronology analyses of the Wingate Wash, northern Owlshead Mountain and Southern Panamint Mountain region document a complex structural history constrained by syntectonic volcanism and sedimentation. In this study, the region is divided into five structural domains with distinct, but related, histories: (1) The southern Panamint domain is a structurally intact, gently south-tilted block dominated by a middle Miocene volcanic center recognized as localized hypabyssal intrusives surrounded by proximal facies pyroclastic rocks. This Miocene volcanic sequence is an unusual alkaline volcanic assemblage ranging from trachybasalt to rhyolite, but dominated by trachyandesite. The volcanic rocks are overlain in the southwestern Panamint Mountains by a younger (Late Miocene?) fanglomerate sequence. (2) An upper Wingate Wash domain is characterized by large areas of Quaternary cover and complex overprinting of older structure by Quaternary deformation. Quaternary structures record ???N-S shortening concurrent with ???E-W extension accommodated by systems of strike-slip and thrust faults. (3) A central Wingate Wash domain contains a complex structural history that is closely tied to the stratigraphic evolution. In this domain, a middle Miocene volcanic package contains two distinct assemblages; a lower sequence dominated by alkaline pyroclastic rocks similar to the southern Panamint sequence and an upper basaltic sequence of alkaline basalt and basanites. This volcanic sequence is in turn overlain by a coarse clastic sedimentary sequence that records the unroofing of adjacent ranges and development of ???N-S trending, west-tilted fault blocks. We refer to this sedimentary sequence as the Lost Lake assemblage. (4) The lower Wingate Wash/northern Owlshead domain is characterized by a gently north-dipping stratigraphic sequence with an irregular unconformity at the base developed on granitic basement. The unconformity is locally overlain by channelized deposits of older Tertiary(?) red conglomerate, some of which predate the onset of extensive volcanism, but in most of the area is overlain by a moderately thick package of Middle Miocene trachybasalt, trachyandesitic, ash flows, lithic tuff, basaltic cinder, basanites, and dacitic pyroclastic, debris, and lahar flows with localized exposures of sedimentary rocks. The upper part of the Miocene stratigraphic sequence in this domain is comprised of coarse grained-clastic sediments that are apparently middle Miocene based on Ar/Ar dating of interbedded volcanic rocks. This sedimentary sequence, however, is lithologically indistinguishable from the structurally adjacent Late Miocene Lost Lake assemblage and a stratigraphically overlying Plio-Pleistocene alluvial fan; a relationship that handicaps tracing structures through this domain. This domain is also structurally complex and deformed by a series of northwest-southeast-striking, east-dipping, high-angle oblique, sinistral, normal faults that are cut by left-lateral strike-slip faults. The contact between the southern Panamint domain and the adjacent domains is a complex fault system that we interpret as a zone of Late Miocene distributed sinistral slip that is variably overprinted in different portions of the mapped area. The net sinistral slip across the Wingate Wash fault system is estimated at 7-9 km, based on offset of Proterozoic Crystal Springs Formation beneath the middle Miocene unconformity to as much as 15 km based on offset volcanic facies in Middle Miocene rocks. To the south of Wingate Wash, the northern Owlshead Mountains are also cut by a sinistral, northwest-dipping, oblique normal fault, (referred to as the Filtonny Fault) with significant slip that separates the Lower Wingate Wash and central Owlshead domains. The Filtonny Fault may represent a young conjugate fault to the dextral Southern Death Valley fault system and may be the northwest

Spatiotemporal analysis of Quaternary normal faults in the Northern Rocky Mountains, USA

NASA Astrophysics Data System (ADS)

Davarpanah, A.; Babaie, H. A.; Reed, P.

2010-12-01

The mid-Tertiary Basin-and-Range extensional tectonic event developed most of the normal faults that bound the ranges in the northern Rocky Mountains within Montana, Wyoming, and Idaho. The interaction of the thermally induced stress field of the Yellowstone hot spot with the existing Basin-and-Range fault blocks, during the last 15 my, has produced a new, spatially and temporally variable system of normal faults in these areas. The orientation and spatial distribution of the trace of these hot-spot induced normal faults, relative to earlier Basin-and-Range faults, have significant implications for the effect of the temporally varying and spatially propagating thermal dome on the growth of new hot spot related normal faults and reactivation of existing Basin-and-Range faults. Digitally enhanced LANDSAT 7 Enhanced Thematic Mapper Plus (ETM+) and Landsat 4 and 5 Thematic Mapper (TM) bands, with spatial resolution of 30 m, combined with analytical GIS and geological techniques helped in determining and analyzing the lineaments and traces of the Quaternary, thermally-induced normal faults in the study area. Applying the color composite (CC) image enhancement technique, the combination of bands 3, 2 and 1 of the ETM+ and TM images was chosen as the best statistical choice to create a color composite for lineament identification. The spatiotemporal analysis of the Quaternary normal faults produces significant information on the structural style, timing, spatial variation, spatial density, and frequency of the faults. The seismic Quaternary normal faults, in the whole study area, are divided, based on their age, into four specific sets, which from oldest to youngest include: Quaternary (>1.6 Ma), middle and late Quaternary (>750 ka), latest Quaternary (>15 ka), and the last 150 years. A density map for the Quaternary faults reveals that most active faults are near the current Yellowstone National Park area (YNP), where most seismically active faults, in the past 1.6 my, are located. The GIS based autocorrelation method, applied to the trace orientation, length, frequency, and spatial distribution for each age-defined fault set, revealed spatial homogeneity for each specific set. The results of the method of Moran`sI and Geary`s C show no spatial autocorrelation among the trend of the fault traces and their location. Our results suggest that while lineaments of similar age define a clustered pattern in each domain, the overall distribution pattern of lineaments with different ages seems to be non-uniform (random). The directional distribution analysis reveals a distinct range of variation for fault traces of different ages (i.e., some displaying ellipsis behavior). Among the Quaternary normal fault sets, the youngest lineament set (i.e., last 150 years) defines the greatest ellipticity (eccentricity) and the least lineaments distribution variation. The frequency rose diagram for the entire Quaternary normal faults, shows four major modes (around 360o, 330o, 300o, and 270o), and two minor modes (around 235 and 205).

Holocene paleoseismicity, temporal clustering, and probabilities of future large (M > 7) earthquakes on the Wasatch fault zone, Utah

USGS Publications Warehouse

McCalpin, J.P.; Nishenko, S.P.

1996-01-01

The chronology of M>7 paleoearthquakes on the central five segments of the Wasatch fault zone (WFZ) is one of the best dated in the world and contains 16 earthquakes in the past 5600 years with an average repeat time of 350 years. Repeat times for individual segments vary by a factor of 2, and range from about 1200 to 2600 years. Four of the central five segments ruptured between ??? 620??30 and 1230??60 calendar years B.P. The remaining segment (Brigham City segment) has not ruptured in the past 2120??100 years. Comparison of the WFZ space-time diagram of paleoearthquakes with synthetic paleoseismic histories indicates that the observed temporal clusters and gaps have about an equal probability (depending on model assumptions) of reflecting random coincidence as opposed to intersegment contagion. Regional seismicity suggests that for exposure times of 50 and 100 years, the probability for an earthquake of M>7 anywhere within the Wasatch Front region, based on a Poisson model, is 0.16 and 0.30, respectively. A fault-specific WFZ model predicts 50 and 100 year probabilities for a M>7 earthquake on the WFZ itself, based on a Poisson model, as 0.13 and 0.25, respectively. In contrast, segment-specific earthquake probabilities that assume quasi-periodic recurrence behavior on the Weber, Provo, and Nephi segments are less (0.01-0.07 in 100 years) than the regional or fault-specific estimates (0.25-0.30 in 100 years), due to the short elapsed times compared to average recurrence intervals on those segments. The Brigham City and Salt Lake City segments, however, have time-dependent probabilities that approach or exceed the regional and fault specific probabilities. For the Salt Lake City segment, these elevated probabilities are due to the elapsed time being approximately equal to the average late Holocene recurrence time. For the Brigham City segment, the elapsed time is significantly longer than the segment-specific late Holocene recurrence time.

Measurement of fault latency in a digital avionic mini processor, part 2

NASA Technical Reports Server (NTRS)

Mcgough, J.; Swern, F.

1983-01-01

The results of fault injection experiments utilizing a gate-level emulation of the central processor unit of the Bendix BDX-930 digital computer are described. Several earlier programs were reprogrammed, expanding the instruction set to capitalize on the full power of the BDX-930 computer. As a final demonstration of fault coverage an extensive, 3-axis, high performance flght control computation was added. The stages in the development of a CPU self-test program emphasizing the relationship between fault coverage, speed, and quantity of instructions were demonstrated.

Physical properties of fault zone rocks from SAFOD: Tying logging data to high-pressure measurements on drill core

NASA Astrophysics Data System (ADS)

Jeppson, T.; Tobin, H. J.

2013-12-01

In the summer of 2005, Phase 2 of the San Andreas Fault Observatory at Depth (SAFOD) borehole was completed and logged with wireline tools including a dipole sonic tool to measure P- and S-wave velocities. A zone of anomalously low velocity was detected from 3150 to 3414 m measured depth (MD), corresponding with the subsurface location of the San Andreas Fault Zone (SAFZ). This low velocity zone is 5-30% slower than the surrounding host rock. Within this broad low-velocity zone, several slip surfaces were identified as well as two actively deforming shear zones: the southwest deformation zone (SDZ) and the central deformation zone (CDZ), located at 3192 and 3302 m MD, respectively. The SAFZ had also previously been identified as a low velocity zone in seismic velocity inversion models. The anomalously low velocity was hypothesized to result from either (a) brittle deformation in the damage zone of the fault, (b) high fluid pressures with in the fault zone, or (c) lithological variation, or a combination of the above. We measured P- and S-wave velocities at ultrasonic frequencies on saturated 2.5 cm diameter core plug samples taken from SAFOD core obtained in 2007 from within the low velocity zone. The resulting values fall into two distinct groups: foliated fault gouge and non-gouge. Samples of the foliated fault gouge have P-wave velocities between 2.3-3.5 km/s while non-gouge samples lie between 4.1-5.4 km/s over a range of effective pressures from 5-70 MPa. There is a good correlation between the log measurements and laboratory values of P-and S wave velocity at in situ pressure conditions especially for the foliated fault gouge. For non-gouge samples the laboratory values are approximately 0.08-0.73 km/s faster than the log values. This difference places the non-gouge velocities within the Great Valley siltstone velocity range, as measured by logs and ultrasonic measurements performed on outcrop samples. As a high fluid pressure zone was not encountered during SAFOD drilling, we use the ultrasonic velocities of SAFOD core and analogous outcrop samples to determine if the velocity reduction is due to lithologic variations or the presence of deformational fabrics and alteration in the fault zone. Preliminary analysis indicates that while the decrease in velocity across the broad fault zone is heavily influenced by fractures, the extremely low velocities associated with the actively deforming zones are more likely caused by the development of scaly fabric with clay coatings on the fracture surfaces. Analysis of thin sections and well logs are used to support this interpretation.

Blind Thrusting, Surface Folding, and the Development of Geological Structure in the Mw 6.3 2015 Pishan (China) Earthquake

NASA Astrophysics Data System (ADS)

Ainscoe, E. A.; Elliott, J. R.; Copley, A.; Craig, T. J.; Li, T.; Parsons, B. E.; Walker, R. T.

2017-11-01

The relationship between individual earthquakes and the longer-term growth of topography and of geological structures is not fully understood, but is key to our ability to make use of topographic and geological data sets in the contexts of seismic hazard and wider-scale tectonics. Here we investigate those relationships at an active fold-and-thrust belt in the southwest Tarim Basin, Central Asia. We use seismic waveforms and interferometric synthetic aperture radar (InSAR) to determine the fault parameters and slip distribution of the 2015 Mw6.3 Pishan earthquake—a blind, reverse-faulting event dipping toward the Tibetan Plateau. Our earthquake mechanism and location correspond closely to a fault mapped independently by seismic reflection, indicating that the earthquake was on a preexisting ramp fault over a depth range of ˜9-13 km. However, the geometry of folding in the overlying fluvial terraces cannot be fully explained by repeated coseismic slip in events such as the 2015 earthquake nor by the early postseismic motion shown in our interferograms; a key role in growth of the topography must be played by other mechanisms. The earthquake occurred at the Tarim-Tibet boundary, with the unusually low dip of 21°. We use our source models from Pishan and a 2012 event to argue that the Tarim Basin crust deforms only by brittle failure on faults whose effective coefficient of friction is ≤0.05 ± 0.025. In contrast, most of the Tibetan crust undergoes ductile deformation, with a viscosity of order 1020-1022 Pa s. This contrast in rheologies provides an explanation for the low dip of the earthquake fault plane.

Morphology of central California continental margin, revealed by long-range side-scan sonar (GLORIA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gardner, J.V.; McCulloch, D.S.; Eittreim, S.L.

1985-02-01

Leg 2 of the 4-leg USGS EEZ-SCAN 84 program used GLORIA long-range side-scan sonar to survey the region from Pt. Conception to just south of Pt. Arena, from the shelf break to the 200-nmi coverage. The overlapping digital sonographs were slant-range and anamorphically corrected, and a photomosaic of the sonographs was constructed at a scale of 1:375,000 (1 in. = 11.1 km). The underlying bed rock appears to be an important control in shaping the morphology of this margin. Several faults have sea-floor expression and lie subparallel to the margin. The density of canyons and gullies on the slope variesmore » from south to north, probably because of variations in the characteristics of the bed rock. The slope west of San Francisco is the most dissected segment of the central California slope. Monterey Fan is covered by large-scale bed forms (5-15 m amplitude and 1.5-2.0 km wavelength) over much of its surface. Monterey channel crosses southwestward across the fan, but abruptly turns south along a 40-km long surface fault that coincides with a well-mapped meander loop. The channel loops to the north then turns southward crossing the entire Monterey Fan, at its distal reaches, changes to a broad, braided pattern. Major slumps on the margin have long (> 30 km) scarps, some have slump folds, and one has a debris-flow deposit that can be acoustically traced for more than 75 km. Seventeen new seamounts were mapped. Taney Seamounts are large, rimmed, calderas with diameters of about 15 km each; these appear to be very large explosive or summit-collapse features.« less

Evaluating the potential for catastrophic fault-rupture-related hazards affecting a key hydroelectric and irrigation region in central Asia

NASA Astrophysics Data System (ADS)

Rust, D.; Korjenkov, A.; Tibaldi, A.; Usmanova, M.

2009-04-01

The Toktogul hydroelectric and irrigation scheme is the largest in central Asia, with a reservoir containing almost 20 km3 of water behind a 230 m-high dam. Annually, the scheme generates 1200 MW of electricity that is distributed over Kyrgyzstan, Uzbekistan, Tajikistan, Kazakhstan and Russia. The scheme is vital for the economic, social and agricultural stability and development of the emerging central Asian republics it serves and, since it is no longer administered centrally as it was in Soviet times, is increasingly the focus of cross-border tensions involving competing needs for irrigation water and power supplies. Our work aims to identify and evaluate potential geo-environmental threats to this region for the benefit of stakeholders; with recommendations for measures to mitigate a range of threat scenarios, presented in a user-friendly GIS format. Most notably these scenarios involve the potential for very large magnitude earthquakes, with associated widespread slope instability, occurring on the little known Talas - Fergana fault. This structure, some 700 km long, bisects the Toktogul region within the actively (~20 mm a-1) contracting Tien Shan mountain range and exhibits geological characteristics similar to large strike-slip faults such as the San Andreas. Historical records are limited in this inaccessible mountainous region that, until Soviet times, was occupied by mainly nomadic peoples, but do not indicate recent fault rupture. This highlights the role of geological investigations in assembling a record of past catastrophic events to serve as a guide for what may be expected in the future, as well as the inherent difficulties in attempting geological forecasts to a precision that is useful on human timescales. Such forecasts in this region must also include the presence of some 23 uranium mining waste dumps within the mountain valleys, a legacy from Soviet times, as well as arsenic-rich waste dumps remaining from an earlier era of gold mining. Many of these toxic dumps are vulnerable to seismically induced landsliding, release of reservoir water and breaching of very large (up to several km3) landslide-dammed lakes within the deep mountain valleys typical of the fault zone. The May 2008 earthquake in neighboring Sichuan, in which some 30 landslide-dammed lakes were created, may be useful in refining hazard scenarios developed from the multi-pronged analysis employed in our study. This analysis involves compiling all relevant existing data, such as seismic archives held in paper format, within the project GIS. Spatial and temporal patterns exhibited by these compiled data, together with focal mechanism determinations where possible, are combined with data on the distribution and nature of geological units to provide estimates of peak ground acceleration and the likely incidence of seismically-triggered slope instability. This compilation also identifies data deficiencies to be targeted using a portable seismometer network, geophysical and geodetic surveys, InSAR and other remote sensing data; all combined with geotechnical and palaeoseismological fieldwork. Initial results from this approach confirm the ground-shaking potential of Talas-Fergana rupture events, suggest a long-term slip rate as high as 15 mm a-1, and the occurrence of the last ground-rupturing event some 4-500 years BP. The lack of significant activity since that event suggests the Talas-Fergana structure may comprise a seismic gap within the Tien-Shan, highlighting the importance of hazard scenarios in proposing mitigation measures against potentially catastrophic threats, such as extensive pollution of irrigated lands in the Fergana Valley downstream from Toktogul on which some 10 million people depend.

Phanerozoic geological evolution of the Equatorial Atlantic domain

NASA Astrophysics Data System (ADS)

Basile, Christophe; Mascle, Jean; Guiraud, René

2005-10-01

The Phanerozoic geological evolution of the Equatorial Atlantic domain has been controlled since the end of Early Cretaceous by the Romanche and Saint Paul transform faults. These faults did not follow the PanAfrican shear zones, but were surimposed on Palæozoic basins. From Neocomian to Barremian, the Central Atlantic rift propagated southward in Cassiporé and Marajó basins, and the South Atlantic rift propagated northward in Potiguar and Benue basins. During Aptian times, the Equatorial Atlantic transform domain appeared as a transfer zone between the northward propagating tip of South Atlantic and the Central Atlantic. Between the transform faults, oceanic accretion started during Late Aptian in small divergent segments, from south to north: Benin-Mundaú, deep Ivorian basin-Barreirinhas, Liberia-Cassiporé. From Late Aptian to Late Albian, the Togo-Ghana-Ceará basins appeared along the Romanche transform fault, and Côte d'Ivoire-Parà-Maranhão basins along Saint Paul transform fault. They were rapidly subsiding in intra-continental settings. During Late Cretaceous, these basins became active transform continental margins, and passive margins since Santonian times. In the same time, the continental edge uplifted leading either to important erosion on the shelf or to marginal ridges parallel to the transform faults in deeper settings.

Shaded Relief with Height as Color, Kunlun fault, east-central Tibet

NASA Image and Video Library

2002-07-11

These two images show exactly the same area, part of the Kunlun fault in northern Tibet. The image on the left was created using the best global topographic data set previously available, the U.S. Geological Survey GTOPO30.

Up-dip partitioning of displacement components on the oblique-slip Clarence Fault, New Zealand

NASA Astrophysics Data System (ADS)

Nicol, Andrew; Van Dissen, Russell

2002-09-01

Active strike-slip faults in New Zealand occur within an obliquely-convergent plate boundary zone. Although the traces of these faults commonly delineate the base of mountain ranges, they do not always accommodate significant shortening at the free surface. Along the active trace of Clarence Fault in northeastern South Island, New Zealand, displaced landforms and slickenside striations indicate predominantly horizontal displacements at the ground surface, and a right-lateral slip rate of ca. 3.5-5 mm/year during the Holocene. The Inland Kaikoura mountain range occupies the hanging wall of the fault and rises steeply from the active trace to altitudes of ca. 3 km. The geomorphology of the range indicates active uplift and mountain building, which is interpreted to result, in part, from a vertical component of fault slip at depth. These data are consistent with the fault accommodating oblique-slip at depth aligned parallel to the plate-motion vector and compatible with regional geodetic data and earthquake focal-mechanisms. Oblique-slip on the Clarence Fault at depth is partitioned at the free surface into: (1) right-lateral displacement on the fault, and (2) hanging wall uplift produced by distributed displacement on small-scale faults parallel to the main fault. Decoupling of slip components reflects an up-dip transfer of fault throw to an off-fault zone of distributed uplift. Such zones are common in the hanging walls of thrusts and reverse faults, and support the idea that the dip of the oblique-slip Clarence Fault steepens towards the free surface.