Quantifying the forcing effect of channel width variations on free bars: Morphodynamic modeling based on characteristic dissipative Galerkin scheme

NASA Astrophysics Data System (ADS)

Wu, Fu-Chun; Shao, Yun-Chuan; Chen, Yu-Chen

2011-09-01

The forcing effect of channel width variations on free bars is investigated in this study using a two-dimensional depth-averaged morphodynamic model. The novel feature of the model is the incorporation of a characteristic dissipative Galerkin (CDG) upwinding scheme in the bed evolution module. A correction for the secondary flows induced by streamline curvature is also included, allowing for simulations of bar growth and migration in channels with width variations beyond the small-amplitude regimes. The model is tested against a variety of experimental data ranging from purely forced and free bars to coexisting bed forms in the variable-width channel. The CDG scheme effectively dissipates local bed oscillations, thus sustains numerical stabilities. The results show that the global effect of width variations on bar height is invariably suppressive. Such effect increases with the dimensionless amplitude AC and wave number λC of width variations. For small AC, λC has little effects on bar height; for AC beyond small amplitudes, however, the suppressing effect depends on both AC and λC. The suppressing effect on bar length increases also with both AC and λC, but is much weaker than that on bar height. The global effect of width variations on bar celerity can be suppressive or enhancive, depending on the combination of AC and λC. For smaller λC, the effect on bar celerity is enhancive; for larger λC, bar celerity tends to increase at small AC but decreases for AC beyond small amplitudes. We present herein an unprecedented data set verifying the theoretical prediction on celerity enhancement. Full suppression of bar growth above the theoretically predicted threshold AC was not observed, regardless of the adopted amplitude of initial bed perturbation A. The global effects of width variations on free bars can be quantified using a forcing factor FC that integrates the effects of AC and λC. The suppressing effects on bar height and length are both proportional to FC2.16; the global effect on bar celerity is, however, a parabolic function of FC.

Measuring the Erosion of River Channel Widths Impacted by Watershed Urbanization Using Historic Aerial Photographs and Modern Surveys

NASA Astrophysics Data System (ADS)

Galster, J. C.; Pazzaglia, F. J.; Germanoski, D.

2007-12-01

Land use in a watershed exerts a strong influence on trunk channel form and process. Land use changes act over human time scales which is short enough to measure their effects directly using historic aerial photographs. We show that high-resolution topographic surveys comparing channel form for paired watersheds in the Lehigh Valley, PA are indistinguishable, but have channel widths that have changed dramatically in the past five decades. The two watersheds, Little Lehigh Creek and Sacony Creek, are similar in all respects except they have different amount of urban land use. Aerial photographs of the urbanized Little Lehigh Creek show that a majority of the measured widths (67 of 85) were statistically wider in 1999 than in 1947. In contrast, the measured widths from the agricultural Sacony Creek are more evenly distributed among those that widened (18), narrowed (28), and those that were statistically unchanged (6) from 1946 to 1999. From 1946 to 1999 the only section of Sacony creek that widened was that reach downstream of the only sizable urban area in the watershed. The current land use in Sacony Creek watershed resembles that of 1946, while the Little Lehigh Creek watershed has more than tripled its urban area. These data suggest that the increase in urban areas that subsequently increases peak discharges is the mechanism behind the widening that occurred in the Little Lehigh Creek. These wider channels can affect water quality, aquatic habitat, suspended sediment loads, and river aesthetics.

Spatial and temporal patterns in channel change on the Snake River downstream from Jackson Lake dam, Wyoming

NASA Astrophysics Data System (ADS)

Nelson, Nicholas C.; Erwin, Susannah O.; Schmidt, John C.

2013-10-01

Operations of Jackson Lake dam (JLD) have altered the hydrology and sediment transport capacity of the Snake River in Grand Teton National Park. Prior research has provided conflicting assessments of whether the downstream river was perturbed into sediment surplus or sediment deficit. In this paper, we present the results of an aerial photo analysis designed to evaluate whether the history of channel change indicates either significant deficit or surplus of sediment that could be expressed as narrowing or expansion of the channel over time. We analyze changes in braid index, channel width, channel activity, and net channel change of the Snake River based on four series of aerial photographs. Between 1945 and 1969, a period of relatively small main-stem floods, widespread deposition, and up to 31% reduction in channel width occurred throughout the Snake River. Between 1969 and 2002, a period of large main-stem floods, the style of channel change reversed with a decrease in braid index and an increase in channel width of up to 31%. These substantial changes in the channel downstream from the dam primarily occurred in multithread reaches, regardless of proximity to tributaries, and no temporal progression of channel narrowing or widening was observed. We demonstrate that channel change downstream from JLD is more temporally and longitudinally complex than previously described.

Mean annual runoff and peak flow estimates based on channel geometry of streams in southeastern Montana

USGS Publications Warehouse

Omang, R.J.; Parrett, Charles; Hull, J.A.

1983-01-01

Equations using channel-geometry measurements were developed for estimating mean runoff and peak flows of ungaged streams in southeastern Montana. Two separate sets of esitmating equations were developed for determining mean annual runoff: one for perennial streams and one for ephemeral and intermittent streams. Data from 29 gaged sites on perennial streams and 21 gaged sites on ephemeral and intermittent streams were used in these analyses. Data from 78 gaged sites were used in the peak-flow analyses. Southeastern Montana was divided into three regions and separate multiple-regression equations for each region were developed that relate channel dimensions to peak discharge having recurrence intervals of 2, 5, 10, 25, 50, and 100 years. Channel-geometery relations were developed using measurements of the active-channel width and bankfull width. Active-channel width and bankfull width were the most significant channel features for estimating mean annual runoff for al types of streams. Use of this method requires that onsite measurements be made of channel width. The standard error of estimate for predicting mean annual runoff ranged from about 38 to 79 percent. The standard error of estimate relating active-channel width or bankfull width to peak flow ranged from about 37 to 115 percent. (USGS)

Effect of channel width variation on sediment transport in mixed alluvial-bedrock rivers - from case study to concept

NASA Astrophysics Data System (ADS)

Cook, Kristen; Turowski, Jens; Hovius, Niels

2017-04-01

In mixed bedrock-alluvial rivers, the response of the system to a flood event can be affected by a number of factors, including coarse sediment availability in the channel, sediment supply from the hillslopes, bedrock-controlled changes in channel width, and the shape of the hydrograph. Local hydraulics and therefore bedload transport capacity depend on discharge and channel geometry, typically quantified by channel width and bed slope. However, the influence of channel width on total bedload transport capacity depends on discharge. For a given slope, narrow channels are more efficient than wide ones at low discharges, while wider channels are more efficient at higher discharges. Therefore, abrupt changes in downstream channel width may affect bedload flux through a channel and have important influences on channel behavior. We use the model sedFlow (Heimann et al., 2014) to explore this effect. We ran the model in a 4.5 km long channel, the center of which contains a 1 km gorge section with a width of 15 m, bounded upstream and downstream by sections with widths of 50 m. We imposed a discharge time series with a random sequence of floods of different size. The channel responds to the imposed floods in complex ways. At high discharges, the gorge reach transports less total sediment than the wide reaches, leading to aggradation in the upper part of the gorge and upstream and erosion in the lower part of the gorge and downstream. At lower discharges, the gorge becomes more efficient at transporting sediment and the trends reverse. The channel may experience both of these regimes during the peak and recession periods of a single flood, leading to a highly dynamic channel bed. This is consistent with observations from the Daan River gorge in western Taiwan, where we observe substantial intra-flood variations in channel bed elevation. Our modeling suggests that width differences alone can drive substantial variations in sediment flux and bed response, without the need for variations in sediment supply or mobility. Because the relationship between channel width and sediment transport capacity depends on the discharge, the long-term response of a channel with variable width depends on the entire hydrograph, not just on the flood peak. In addition, the net effect of a flood depends strongly on the preceding sequence of floods, as the long profile and channel slopes are continually adjusting to different forcing. Therefore modeling studies that use uniform discharge or a step function discharge will miss these dynamics. The fluctuations in sediment transport rates that result from width variations can lead to intermittent bed exposure, driving incision in different segments of the channel during different segments of the hydrograph.

The dynamics of bedrock channel adjustment: Modeling the influence of sediment supply, weathering, and lithology on channel cross-sectional and longitudinal shape

NASA Astrophysics Data System (ADS)

Wobus, C.; Tucker, G.; Anderson, R.; Kean, J.; Small, E.; Hancock, G.

2007-12-01

The cross-sectional form of a natural river channel controls the capacity of the system to carry water off a landscape, to convey sediment derived from hillslopes, and to erode its bed and banks. Numerical models that describe the response of a landscape to changes in climate or tectonics therefore require formulations that can accommodate changes in channel cross-sectional geometry through time. We have developed a 2D numerical model that computes the formation of a channel in a cohesive, detachment-limited substrate subject to steady, unidirectional flow. Boundary shear stress is calculated using a simple approximation of the flow field in which log-velocity profiles are assumed to apply along vectors that are perpendicular to the local boundary surface. The resulting model predictions for the velocity structure, peak boundary shear stress, and equilibrium channel shape compare well with the predictions of a more sophisticated but more computationally demanding ray-isovel model. For example, the mean velocities computed by the two models are consistent to within ~3%, and the predicted peak shear stress is consistent to within ~7%. The efficiency of our model makes it suitable for calculations of long-term morphologic change both in single cross-sections and in series of cross-sections arrayed downstream. For a uniform substrate, the model predicts a strong tendency toward a fixed width-to-depth ratio, regardless of gradient or discharge. The model predicts power-law relationships between width and discharge with an exponent near 2/5, and between width and gradient with an exponent near -1/5. Recent enhancements to the model include the addition of sediment, which increases the width-to-depth ratio at steady state by favoring erosion of the channel walls relative to the channel bed (the "cover effect"). Inclusion of a probability density function of discharges with a simple parameterization of weathering along channel banks leads to the formation of model strath terraces. Downstream changes in substrate erodibility or tectonic uplift rate lead to step-function changes in channel width, consistent with empirical observations. Finally, explicit inclusion of bedload transport allows channel width, gradient, and the pattern of sediment flux to evolve dynamically, allowing us to explore the response of bedrock channels to both spatial patterns of rock uplift, and temporal variations in sediment input.

The significance of sediment transport in arroyo development

USGS Publications Warehouse

Meyer, David F.

1989-01-01

Arroyo widening dominates postincisional arroyo development, and the manner of widening is dependent on the grain size of bed material transported by the channel. When bed material is predominantly gravel, subaqueous bars that alternate from one side of the channel to the other form during high flows in initially narrow, often straight, arroyos. These alternate bars grow and become coarse-grained point bars. Moderate and low flows cannot rework these coarse bars, and the channel meanders around them. Arroyo walls opposite the bars are undercut and eroded. With progressive arroyo widening by erosion of cut banks, high-flow channel width increases, and depth decreases, reducing channel competence. Gravel is deposited in midchannel bars, point bars are reworked, and the channel becomes braided. As braiding becomes dominant, both arroyo walls are eroded. This conceptual model of coarse-grained arroyo development is based on observations of arroyo development through time using physical models and interpretation of the channel and arroyo morphology and sedimentology during a short period along the San Simon, San Pedro, and Santa Cruz Rivers in southeast Arizona. When bed material is predominantly sand, the channel pattern within initial arroyos is typically braided, and both arroyo walls are actively eroded. Alternate bars may form within single-thread, high-flow channels, but they are reworked during recessional flows, and the .low-flow channel is again braided. With progressive arroyo widening, fine sand, silt, and clay carried in suspension are deposited across a flood plain within the wide arroyo, causing the channel to meander. This fine-grained arroyo development model is based on observations of arroyo development through time using physical models and interpretation of the channel and arroyo morphology and sedimentology during a short period along the Rio Puerco, New Mexico. Experimental investigations using physical models in which incised channels were monitored through time indicate that the rate of arroyo widening is dependent on the amount of bedload transported through a reach. This is documented by the relations between the rate of arroyo erosion and the observed sediment transport, the channel slope, the channel width and the channel width-to-depth ratio. When a small amount of bed material is being transported, arroyos do not widen whether they are narrow (arroyo width-to-depth ratios between 1.5 and 3.1), intermediate (between 2.5 and 4.8), or wide (greater than 4.9). Arroyo widening resumes when a larger supply of bed material is introduced. Arroyo widening decreases through time because with progressive increases of arroyo width, the frequency with which unstable channels within the arroyo impinge upon arroyo walls decreases. Arroyos become wider in a downstream direction in response to the cumulative effect of upstream sediment production.

What controls channel form in steep mountain streams?

NASA Astrophysics Data System (ADS)

Palucis, M. C.; Lamb, M. P.

2017-07-01

Steep mountain streams have channel morphologies that transition from alternate bar to step-pool to cascade with increasing bed slope, which affect stream habitat, flow resistance, and sediment transport. Experimental and theoretical studies suggest that alternate bars form under large channel width-to-depth ratios, step-pools form in near supercritical flow or when channel width is narrow compared to bed grain size, and cascade morphology is related to debris flows. However, the connection between these process variables and bed slope—the apparent dominant variable for natural stream types—is unclear. Combining field data and theory, we find that certain bed slopes have unique channel morphologies because the process variables covary systematically with bed slope. Multiple stable states are predicted for other ranges in bed slope, suggesting that a competition of underlying processes leads to the emergence of the most stable channel form.

3D printing of biomimetic microstructures for cancer cell migration.

PubMed

Huang, Tina Qing; Qu, Xin; Liu, Justin; Chen, Shaochen

2014-02-01

To understand the physical behavior and migration of cancer cells, a 3D in vitro micro-chip in hydrogel was created using 3D projection printing. The micro-chip has a honeycomb branched structure, aiming to mimic 3D vascular morphology to test, monitor, and analyze differences in the behavior of cancer cells (i.e. HeLa) vs. non-cancerous cell lines (i.e. 10 T1/2). The 3D Projection Printing system can fabricate complex structures in seconds from user-created designs. The fabricated microstructures have three different channel widths of 25, 45, and 120 microns wide to reflect a range of blood vessel diameters. HeLa and 10 T1/2 cells seeded within the micro-chip were then analyzed for morphology and cell migration speed. 10 T1/2 cells exhibited greater changes in morphology due to channel size width than HeLa cells; however, channel width had a limited effect on 10 T1/2 cell migration while HeLa cancer cell migration increased as channel width decreased. This physiologically relevant 3D cancer tissue model has the potential to be a powerful tool for future drug discoveries and cancer migration studies.

Effect of Channel Thickness, Annealing Temperature and Channel Length on Nanoscale Ga2O3-In2O3-ZnO Thin Film Transistor Performance.

PubMed

Kumaresan, Yogeenth; Pak, Yusin; Lim, Namsoo; Lee, Ryeri; Song, Hui; Kim, Tae Heon; Choi, Boran; Jung, Gun Young

2016-06-01

We demonstrated the effect of active layer (channel) thickness and annealing temperature on the electrical performances of Ga2O3-In2O3-ZnO (GIZO) thin film transistor (TFT) having nanoscale channel width (W/L: 500 nm/100 μm). We found that the electron carrier concentration of the channel was decreased significantly with increasing the annealing temperature (100 degrees C to 300 degrees C). Accordingly, the threshold voltage (V(T)) was shifted towards positive voltage (-12.2 V to 10.8 V). In case of channel thickness, the V(T) was shifted towards negative voltage with increasing the channel thickness. The device with channel thickness of 90 nm annealed at 200 degrees C revealed the best device performances in terms of mobility (10.86 cm2/Vs) and V(T) (0.8 V). The effect of channel length was also studied, in which the channel width, thickness and annealing temperature were kept constant such as 500 nm, 90 nm and 200 degrees C, respectively. The channel length influenced the on-current level significantly with small variation of V(T), resulting in lower value of on/off current ratio with increasing the channel length. The device with channel length of 0.5 μm showed enhanced on/off current ratio of 10(6) with minimum V(T) of 0.26 V.

Revised techniques for estimating peak discharges from channel width in Montana

USGS Publications Warehouse

Parrett, Charles; Hull, J.A.; Omang, R.J.

1987-01-01

This study was conducted to develop new estimating equations based on channel width and the updated flood frequency curves of previous investigations. Simple regression equations for estimating peak discharges with recurrence intervals of 2, 5, 10 , 25, 50, and 100 years were developed for seven regions in Montana. The standard errors of estimates for the equations that use active channel width as the independent variables ranged from 30% to 87%. The standard errors of estimate for the equations that use bankfull width as the independent variable ranged from 34% to 92%. The smallest standard errors generally occurred in the prediction equations for the 2-yr flood, 5-yr flood, and 10-yr flood, and the largest standard errors occurred in the prediction equations for the 100-yr flood. The equations that use active channel width and the equations that use bankfull width were determined to be about equally reliable in five regions. In the West Region, the equations that use bankfull width were slightly more reliable than those based on active channel width, whereas in the East-Central Region the equations that use active channel width were slightly more reliable than those based on bankfull width. Compared with similar equations previously developed, the standard errors of estimate for the new equations are substantially smaller in three regions and substantially larger in two regions. Limitations on the use of the estimating equations include: (1) The equations are based on stable conditions of channel geometry and prevailing water and sediment discharge; (2) The measurement of channel width requires a site visit, preferably by a person with experience in the method, and involves appreciable measurement errors; (3) Reliability of results from the equations for channel widths beyond the range of definition is unknown. In spite of the limitations, the estimating equations derived in this study are considered to be as reliable as estimating equations based on basin and climatic variables. Because the two types of estimating equations are independent, results from each can be weighted inversely proportional to their variances, and averaged. The weighted average estimate has a variance less than either individual estimate. (Author 's abstract)

A New Approach to Scaling Channel Width in Bedrock Rivers and its Implications for Modeling Fluvial Incision

NASA Astrophysics Data System (ADS)

Finnegan, N. J.; Roe, G.; Montgomery, D. R.; Hallet, B.

2004-12-01

The fundamental role of bedrock channel incision on the evolution of mountainous topography has become a central concept in tectonic geomorphology over the past decade. During this time the stream power model of bedrock river incision has immerged as a valuable tool for exploring the dynamics of bedrock river incision in time and space. In most stream power analyses, river channel width--a necessary ingredient for calculating power or shear stress per unit of bed area--is assumed to scale solely with discharge. However, recent field-based studies provide evidence for the alternative view that channel width varies locally, much like channel slope does, in association with spatial changes in rock uplift rate and erodibility. This suggests that simple scaling relations between width and discharge, and hence estimates of stream power, don't apply in regions where rock uplift and erodibility vary spatially. It also highlights the need for an alternative to the traditional assumptions of hydraulic geometry to further investigation of the coupling between bedrock river incision and tectonic processes. Based on Manning's equation, basic mass conservation principles, and an assumption of self-similarity for channel cross sections, we present a new relation for scaling the steady-state width of bedrock river channels as a function of discharge (Q), channel slope (S), and roughness (Ks): W \\propto Q3/8S-3/16Ks1/16. In longitudinally simple, uniform-concavity rivers from the King Range in coastal Northern California, the model emulates traditional width-discharge relations that scale channel width with the square root of discharge. More significantly, our relation describes river width trends for the Yarlung Tsangpo in SE Tibet and the Wenatchee River in the Washington Cascades, both rivers that narrow considerably as they incise terrain with spatially varied rock uplift rates and/or lithology. We suggest that much of observed channel width variability is a simple consequence of the tendency for water to flow faster in steeper reaches and therefore maintain smaller channel cross sections. We demonstrate that using conventional scaling relations for bedrock channel width can significantly underestimate stream power variability in bedrock channels, and that our model improves estimates of spatial patterns of bedrock incision rates.

Packings of monodisperse emulsions in flat microfluidic channels

NASA Astrophysics Data System (ADS)

Claussen, Ohle; Herminghaus, Stephan; Brinkmann, Martin

2012-06-01

In the lateral confinement of a flat microfluidic channel, monodisperse emulsion droplets spontaneously self-organize in a variety of topologically different packings. The explicit construction of mechanically equilibrated arrangements of effectively two-dimensional congruent droplet shapes reveals the existence of multiple mechanical equilibria depending on channel width W, droplet area Ad, and volume fraction φ of the dispersed phase. The corresponding boundaries of local or global stability are summarized in a packing diagram for congruent droplet shapes in terms of the dimensionless channel width w=W/Ad and φ. In agreement with experimental results, an increasingly strong hysteresis of the transition between single-row and two-row packings is observed during changes of w above a threshold volume fraction of φ*≃0.813.

Physically Modeling Stream Channel Adjustment to Woody Riparian Vegetation

NASA Astrophysics Data System (ADS)

Bennett, S. J.; Alonso, C. V.

2003-12-01

Stream restoration designs often use vegetation to promote bank and channel stability, to facilitate point-bar development, and to encourage natural colonization of riparian species. Here we examine the adjustment of an alluvial channel to in-stream and riparian vegetation using a distorted Froude-scale flume model with a movable boundary. A decimeter-scale trapezoidal channel comprised of 0.8-mm diameter sand was systematically vegetated with emergent, rigid dowels (3-mm in diameter) in rectangular and hemispherical patterns with varying vegetation densities while conserving the shape of the zone and the geometry of the vegetal patterns. Alternate sides of the channel were vegetated at the prescribed spacing of equilibrium alternate bars, ca. 5 to 7 times the channel width. Using flow conditions just below the threshold of sediment motion, flow obstruction, deflection, and acceleration caused bed erosion, bank failure, and morphologic channel adjustments that were wholly attributable to the managed plantings. As vegetation density increased, the magnitude and rate of scaled channel adjustment increased, which included increased channel widths, bankline steepening and meandering, and thalweg meandering. As the modeled channel began to meander, the stream bed aggraded and flow depth decreased markedly, creating a continuously connected, inter-reach complex of mid-channel bars. This study demonstrates the utility of using managed vegetations in stream corridor design and meander development, and it provides the practitioner with guidance on the magnitude of channel adjustment as it relates to vegetation density, shape, and spacing.

Enhancement mode GaN-based multiple-submicron channel array gate-recessed fin metal-oxide-semiconductor high-electron mobility transistors

NASA Astrophysics Data System (ADS)

Lee, Ching-Ting; Wang, Chun-Chi

2018-04-01

To study the function of channel width in multiple-submicron channel array, we fabricated the enhancement mode GaN-based gate-recessed fin metal-oxide-semiconductor high-electron mobility transistors (MOS-HEMTs) with a channel width of 450 nm and 195 nm, respectively. In view of the enhanced gate controllability in a narrower fin-channel structure, the transconductance was improved from 115 mS/mm to 151 mS/mm, the unit gain cutoff frequency was improved from 6.2 GHz to 6.8 GHz, and the maximum oscillation frequency was improved from 12.1 GHz to 13.1 GHz of the devices with a channel width of 195 nm, compared with the devices with a channel width of 450 nm.

Mixing behavior of the rhombic micromixers over a wide Reynolds number range using Taguchi method and 3D numerical simulations.

PubMed

Chung, C K; Shih, T R; Chen, T C; Wu, B H

2008-10-01

A planar micromixer with rhombic microchannels and a converging-diverging element has been systematically investigated by the Taguchi method, CFD-ACE simulations and experiments. To reduce the footprint and extend the operation range of Reynolds number, Taguchi method was used to numerically study the performance of the micromixer in a L(9) orthogonal array. Mixing efficiency is prominently influenced by geometrical parameters and Reynolds number (Re). The four factors in a L(9) orthogonal array are number of rhombi, turning angle, width of the rhombic channel and width of the throat. The degree of sensitivity by Taguchi method can be ranked as: Number of rhombi > Width of the rhombic channel > Width of the throat > Turning angle of the rhombic channel. Increasing the number of rhombi, reducing the width of the rhombic channel and throat and lowering the turning angle resulted in better fluid mixing efficiency. The optimal design of the micromixer in simulations indicates over 90% mixing efficiency at both Re > or = 80 and Re < or = 0.1. Experimental results in the optimal simulations are consistent with the simulated one. This planar rhombic micromixer has simplified the complex fabrication process of the multi-layer or three-dimensional micromixers and improved the performance of a previous rhombic micromixer at a reduced footprint and lower Re.

Heat Budget of Large Rivers: Sensitivity to Stream Morphology

NASA Astrophysics Data System (ADS)

Lancaster, S. T.; Haggerty, R.

2014-12-01

In order to assess the feasibility of effecting measurable changes in the heat budget of a large river through restoration, we use a numerical model to analyze the sensitivity of that heat budget to morphological manipulations, specifically those resulting in a narrower main channel with more alcoves. We base model parameters primarily on the gravel-bedded middle Snake River near Marsing, Idaho. The heat budget is represented by an advection-dispersion-reaction equation with, in addition to radiative, evaporative, and sensible heat fluxes, a hyporheic flux term that models lateral flow from the main stream, through bars, and into alcoves and side channels. This term effectively introduces linear dispersion of water temperatures with respect to time, so that the magnitude of the hyporheic term in the heat budget is expected to scale with the ``hyporheic number," defined as , where is dimensionless hyporheic flow rate and is dimensionless mean residence time of water entering the hyporheic zone. Simulations varying the parameters for channel width and hyporheic flow indicate that, for a large river such as the middle Snake River, feasible changes in channel width would produce downstream changes in heat flux an order of magnitude larger than would relatively extreme changes in hyporheic number. Changes, such as reduced channel width and increased hyporheic number, that tend to reduce temperatures in the summer, when temperatures are increasing with time and downstream distance, actually tend to increase temperatures in the fall, when temperatures are decreasing with time and distance.

Effects of debris flow composition on runout, depositional mechanisms, and deposit morphology in laboratory experiments

NASA Astrophysics Data System (ADS)

Haas, Tjalling; Braat, Lisanne; Leuven, Jasper R. F. W.; Lokhorst, Ivar R.; Kleinhans, Maarten G.

2015-09-01

Predicting debris flow runout is of major importance for hazard mitigation. Apart from topography and volume, runout distance and area depends on debris flow composition and rheology, but how is poorly understood. We experimentally investigated effects of composition on debris flow runout, depositional mechanisms, and deposit geometry. The small-scale experimental debris flows were largely similar to natural debris flows in terms of flow behavior, deposit morphology, grain size sorting, channel width-depth ratio, and runout. Deposit geometry (lobe thickness and width) in our experimental debris flows is largely determined by composition, while the effects of initial conditions of topography (i.e., outflow plain slope and channel slope and width) and volume are negligible. We find a clear optimum in the relations of runout with coarse-material fraction and clay fraction. Increasing coarse-material concentration leads to larger runout. However, excess coarse material results in a large accumulation of coarse debris at the flow front and enhances diffusivity, increasing frontal friction and decreasing runout. Increasing clay content initially enhances runout, but too much clay leads to very viscous flows, reducing runout. Runout increases with channel slope and width, outflow plain slope, debris flow volume, and water fraction. These results imply that debris flow runout depends at least as much on composition as on topography. This study improves understanding of the effects of debris flow composition on runout and may aid future debris flow hazard assessments.

Study of gas-water flow in horizontal rectangular channels

NASA Astrophysics Data System (ADS)

Chinnov, E. A.; Ron'shin, F. V.; Kabov, O. A.

2015-09-01

The two-phase flow in the narrow short horizontal rectangular channels 1 millimeter in height was studied experimentally. The features of formation of the two-phase flow were studied in detail. It is shown that with an increase in the channel width, the region of the churn and bubble regimes increases, compressing the area of the jet flow. The areas of the annular and stratified flow patterns vary insignificantly.

Modeling Fluvial Incision and Transient Landscape Evolution: Influence of Dynamic Channel Adjustment

NASA Astrophysics Data System (ADS)

Attal, M.; Tucker, G. E.; Cowie, P. A.; Whittaker, A. C.; Roberts, G. P.

2007-12-01

Channel geometry exerts a fundamental control on fluvial processes. Recent work has shown that bedrock channel width (W) depends on a number of parameters, including channel slope, and is not only a function of drainage area (A) as is commonly assumed. The present work represents the first attempt to investigate the consequences, for landscape evolution, of using a static expression of channel width (W ~ A0.5) versus a relationship that allows channels to dynamically adjust to changes in slope. We consider different models for the evolution of the channel geometry, including constant width-to-depth ratio (after Finnegan et al., Geology, v. 33, no. 3, 2005), and width-to-depth ratio varying as a function of slope (after Whittaker et al., Geology, v. 35, no. 2, 2007). We use the Channel-Hillslope Integrated Landscape Development (CHILD) model to analyze the response of a catchment to a given tectonic disturbance. The topography of a catchment in the footwall of an active normal fault in the Apennines (Italy) is used as a template for the study. We show that, for this catchment, the transient response can be fairly well reproduced using a simple detachment-limited fluvial incision law. We also show that, depending on the relationship used to express channel width, initial steady-state topographies differ, as do transient channel width, slope, and the response time of the fluvial system. These differences lead to contrasting landscape morphologies when integrated at the scale of a whole catchment. Our results emphasize the importance of channel width in controlling fluvial processes and landscape evolution. They stress the need for using a dynamic hydraulic scaling law when modeling landscape evolution, particularly when the uplift field is non-uniform.

Ground beetle communities in a mountain river subjected to restoration: The Raba River, Polish Carpathians.

PubMed

Bednarska, Agnieszka J; Wyżga, Bartłomiej; Mikuś, Paweł; Kędzior, Renata

2018-01-01

Effects of passive restoration of mountain rivers on the organisms inhabiting exposed riverine sediments are considerably less understood than those concerning aquatic biota. Thus, the effects of a recovery of the Raba River after abandonment of maintenance of its channelization scheme on ground beetle (Coleoptera: Carabidae) communities were investigated by comparing 6 unmanaged cross-sections and 6 cross-sections from adjacent channelized reaches. In each cross-section, ground beetles were collected from 12 sampling sites in spring, summer, and autumn, and 8 habitat parameters characterizing the cross-sections and sampling sites were determined. Within a few years after abandonment of the Raba River channelization scheme, the width of this gravel-bed river increased up to three times and its multi-thread pattern became re-established. Consequently, unmanaged river cross-sections had significantly larger channel width and more low-flow channels and eroding cutbanks than channelized cross-sections. Moreover, sampling sites in the unmanaged cross-sections were typified by significantly steeper average surface slope and larger average distance from low-flow channels than the sites in channelized cross-sections. In total, 3992 individuals from 78 taxa were collected during the study. The ground beetle assemblages were significantly more abundant and richer in species in the unmanaged than in the channelized cross-sections but no significant differences in carabid diversity indices between the two cross-section types were recorded. Redundancy Analysis indicated active river zone width as the only variable explaining differences in abundance and species richness among the cross-sections. Multiple regression analysis indicated species diversity to predominantly depend on the degree of plant cover and substrate grain size. The study showed that increased availability of exposed sediments in the widened river reaches allowed ground beetles to increase their abundance and species richness within a few years after the onset of river restoration, but more time may be needed for development of more diverse carabid communities. Copyright © 2017 Elsevier B.V. All rights reserved.

Thermal behavior of Charmonium in the vector channel from QCD sum rules

NASA Astrophysics Data System (ADS)

Dominguez, C. A.; Loewe, M.; Rojas, J. C.; Zhang, Y.

2010-11-01

The thermal evolution of the hadronic parameters of charmonium in the vector channel, i.e. the J/Ψ resonance mass, coupling (leptonic decay constant), total width, and continuum threshold are analyzed in the framework of thermal Hilbert moment QCD sum rules. The continuum threshold s0 has the same behavior as in all other hadronic channels, i.e. it decreases with increasing temperature until the PQCD threshold s0 = 4mQ2 is reached at T≃1.22Tc (mQ is the charm quark mass). The other hadronic parameters behave in a very different way from those of light-light and heavy-light quark systems. The J/Ψ mass is essentially constant in a wide range of temperatures, while the total width grows with temperature up to T≃1.04Tc beyond which it decreases sharply with increasing T. The resonance coupling is also initially constant beginning to increase monotonically around T≃Tc. This behavior of the total width and of the leptonic decay constant is a strong indication that the J/Ψ resonance might survive beyond the critical temperature for deconfinement, in agreement with some recent lattice QCD results.

Modeling Paragenesis: Erosion Opposite to Gravity in Cave Channels

NASA Astrophysics Data System (ADS)

Cooper, M. P.; Covington, M. D.

2017-12-01

Sediment plays an important role in bedrock channels, providing both tools and cover that influence patterns of bed erosion. It has also been shown that sediment load influences bedrock channel width, with increased sediment leading to wider channels. A variety of models have been developed to explore these effects. In caves, it is hypothesized that sediments covering the floors of fully flooded channels that are forming beneath the water table (phreatic zone) can force dissolution upwards towards the water table, leading to upward erosion balanced by gradual deposition of sediment within the channel bottom. This strange process is termed paragenesis, and while there are conceptual and experimental models of the process, no prior mathematical models of cave passage evolution has captured these effects. Consequently, there is little quantitative understanding of the processes that drive paragenesis and how they link to the morphology of the cave channels that develop. We adapt a previously developed algorithm for estimating boundary shear stress within channels with free-surface flows to enable calculation of boundary shear stress in pipe-full conditions. This model successfully duplicates scaling relationships in surface channels, and geometries of caves formed in the phreatic zone such as phreatic tubes. Once sediment flux is incorporated the model successfully duplicates the hypothesized processes of paragenetic gallery formation: the cover effect prevents dissolution in the direction of gravity; passages are enlarged upwards reducing the sediment transport capacity; sediment is deposited and the process drives a continuing feedback loop. Simulations reveal that equilibrium paragenetic channel widths scale with both sediment flux and discharge. Unlike in open channel settings, increased sediment load actually narrows paragenetic channels. The cross section evolution model also reveals that the existence of equilibrium widths in such galleries requires erosion to scale with shear stress, suggesting a role of either mechanical erosion or transport limited dissolution. These types of erosion contrast with current numerical models of speleogenesis, where chemically limited dissolution, a process independent of shear stress, is predicted to occur in most turbulent flow settings.

Introducing an R-package for calculating channel width and other basic metrics for irregular river polygons

NASA Astrophysics Data System (ADS)

Golly, Antonius; Turowski, Jens

2017-04-01

The width of fluvial streams and channel beds is an important metric for a large number of hydraulic, geomorphic and ecologic applications. For example, for a given discharge the local channel width determines the water flow velocity and thus the sediment transport capacity of a reach. Since streams often have irregular shapes with uneven channel banks, the channel width strongly varies along the channel. Although, the geometry of streams or their beds can be measured easily in the field (e.g. with a Total Station or GPS) or from maps or aerial images in a GIS, the width of the stream cannot be identified objectively without further data processing, since the results are more or less irregular polygons with sometimes bended shapes. An objective quantification of the channel width and other metrics requires automated algorithms that are applicable over a range of channel shapes and spatial scales. Here, we present a lightweight software suite with a small number of functions that process 2D or 3D geometrical data of channels or channel beds. The software, written as an R-package, accepts various text data formats and can be configured through five parameters. It creates interactive overview plots (if desired) and produces three basic channel metrics: the centerline, the channel width along the centerline and the slope along the centerline. The centerline is an optimized line that minimizes the distances to both channel banks. This centerline gives also a measure for the real length and slope of the channel. From this centerline perpendicular transects are generated which allow for the calculation of the channel width where they intersect with the channel banks. Briefly, we present an example and demonstrate the importance of these metrics in a use case of a steep stream, the Erlenbach stream in Switzerland. We were motivated to develop and publish the algorithm in an open-source framework, since only proprietary solutions were available at that time. The software is developed in R and is published under GNU GPL meaning it is free to use, edit and copy. This makes the software available also to users who do not own a MATLAB or ARCMAP license for which similar products exist.

The threshold of vapor channel formation in water induced by pulsed CO2 laser

NASA Astrophysics Data System (ADS)

Guo, Wenqing; Zhang, Xianzeng; Zhan, Zhenlin; Xie, Shusen

2012-12-01

Water plays an important role in laser ablation. There are two main interpretations of laser-water interaction: hydrokinetic effect and vapor phenomenon. The two explanations are reasonable in some way, but they can't explain the mechanism of laser-water interaction completely. In this study, the dynamic process of vapor channel formation induced by pulsed CO2 laser in static water layer was monitored by high-speed camera. The wavelength of pulsed CO2 laser is 10.64 um, and pulse repetition rate is 60 Hz. The laser power ranged from 1 to 7 W with a step of 0.5 W. The frame rate of high-speed camera used in the experiment was 80025 fps. Based on high-speed camera pictures, the dynamic process of vapor channel formation was examined, and the threshold of vapor channel formation, pulsation period, the volume, the maximum depth and corresponding width of vapor channel were determined. The results showed that the threshold of vapor channel formation was about 2.5 W. Moreover, pulsation period, the maximum depth and corresponding width of vapor channel increased with the increasing of the laser power.

Quantum ballistic transport by interacting two-electron states in quasi-one-dimensional channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Danhong; Center for High Technology Materials, University of New Mexico, 1313 Goddard St SE, Albuquerque, New Mexico 87106; Gumbs, Godfrey

2015-11-15

For quantum ballistic transport of electrons through a short conduction channel, the role of Coulomb interaction may significantly modify the energy levels of two-electron states at low temperatures as the channel becomes wide. In this regime, the Coulomb effect on the two-electron states is calculated and found to lead to four split energy levels, including two anticrossing-level and two crossing-level states. Moreover, due to the interplay of anticrossing and crossing effects, our calculations reveal that the ground two-electron state will switch from one anticrossing state (strong confinement) to a crossing state (intermediate confinement) as the channel width gradually increases andmore » then back to the original anticrossing state (weak confinement) as the channel width becomes larger than a threshold value. This switching behavior leaves a footprint in the ballistic conductance as well as in the diffusion thermoelectric power of electrons. Such a switching is related to the triple spin degeneracy as well as to the Coulomb repulsion in the central region of the channel, which separates two electrons away and pushes them to different channel edges. The conductance reoccurrence region expands from the weak to the intermediate confinement regime with increasing electron density.« less

The Application of the Specific Gage Technique and Aerial Photographs in Kaskaskia River Degradation Studies

NASA Astrophysics Data System (ADS)

Du, X.

2008-12-01

The Kaskaskia River basin contains 136,000 acres of bottomland forest, the largest contiguous tract of bottomland forest remaining in the state of Illinois. Since the 1960's, the Carlyle Lake Dam impoundment and channelization activities have altered the natural hydrologic and ecological equilibrium of the Kaskaskia River. Morphological changes of the river channel have necessitated conservation and restoration efforts to create and maintain the sustainability, diversity, health, and connectivity of the river watershed. This study utilized the specific gage technique and historical aerial photographs to investigate the spatial and temporal changes of the river. Historical daily discharge and daily stage data from the Carlyle (1966 to 2002) and Venedy Station gages (1984 to 2003) were analyzed. Logs of daily discharge data were used to generate annual rating curves. The best fit equations were produced from annual rating regressions. A stage associated with a chosen reference discharge, the minimum available discharge (MAD), was calculated. A stage decreasing/increasing trend was used as a primary indicator of channel bed incision/aggradation. Pseudo specific gage analysis (PSGA) was used to model channel cross sectional geometry changes over time. PSGA applied similar procedures as compared to the specific gage technique. Instead of using the stage variable, PSGA utilized cross sectional width, cross-sectional area, mean velocity and gage height individually. At each gage, the historical change of each cross sectional parameter was plotted against the log of discharge. Ratings of specific stages, specific cross sectional width, specific depth, specific area, and specific velocity associated with the chosen discharge, MAD, were produced. The decreasing/increasing trend of each parameter mentioned above corresponded with changes of channel cross sectional geometries over time. Historical aerial photographs were also used to assess the bankfull channel width changing rates during the pre and post modification period. The statistical significance of the regression trendlines from the specific gage analyses and PSGA was tested. Results suggested that there was no significant channel bed incision trend near the river gages within the studied time period. A statistically significant increase in channel width changing rates was found during post-modification period. Following the channelization and dam construction on the Kaskaskia River, substantial channel bed widening has accelerated bank erosion and associated channel morphology change, which has consequently resulted in a net loss of riparian habitat in this important bottomland forest corridor in southern Illinois, USA.

Jamming of Cylindrical Grains in Featureless Vertical Channels

NASA Astrophysics Data System (ADS)

Baxter, G. William; Barr, Nicholas; Weible, Seth; Friedl, Nicholas

2013-03-01

We study jamming of low aspect-ratio cylindrical Delrin grains falling through a featureless vertical channel. With a grain height less than the grain diameter, these grains resemble aspirin tablets, poker chips, or coins. Unidisperse grains are allowed to fall under the influence of gravity through a uniform channel of square cross-section where the channel width is greater than the grain size and constant along the length of the channel. Channel widths are chosen so that no combination of grain heights and diameters is equal to the channel width. Collections of grains sometimes form jams, stable structures in which the grains are supported by the channel walls and not by grains or walls beneath them. The probability of a jam occurring and the jam's strength are influenced by the grain dimensions and channel width. We will present experimental measurements of the jamming probability and jam strength and discuss the relationship of these results to other experiments and theories. Supported by an Undergraduate Research Grant from Penn State Erie, The Behrend College

Contact resistance reduction of ZnO thin film transistors (TFTs) with saw-shaped electrode.

PubMed

Park, Woojin; Shaikh, Sohail F; Min, Jung-Wook; Lee, Sang Kyung; Lee, Byoung Hun; Hussain, Muhammad M

2018-08-10

We report on a saw-shaped electrode architecture ZnO thin film transistor (TFT), which effectively increases the channel width. The contact line of the saw-shaped electrode is almost twice as long at the contact metal/ZnO channel junction. We experimentally observed an enhancement in the output drive current by 50% and a reduction in the contact resistance by over 50%, when compared to a typically shaped electrode ZnO TFT consuming the same chip area. This performance enhancement is attributed to the extension of the channel width. This technique can contribute to device performance enhancement, and in particular reduce the contact resistance, which is a serious challenge.

Transposition of a Process-Based Model, Flumy: from Meandering Fluvial Systems to Channelized Turbidite Systems

NASA Astrophysics Data System (ADS)

Lemay, M.; Cojan, I.; Rivoirard, J.; Grimaud, J. L.; Ors, F.

2017-12-01

Channelized turbidite systems are among the most important hydrocarbon reservoirs. Yet building realistic turbidite reservoir models is still a challenge. Flumy has been firstly developed to simulate the long-term evolution of aggrading meandering fluvial systems in order to build facies reservoir models. In this study, Flumy has been transposed to channelized turbidite systems. The channel migration linear model of Imran et al. (1999) dedicated to subaqueous flows has been implemented. The whole model has been calibrated taking into account the differences on channel morphology, avulsion frequency, and aggradation and migration rates. This calibration and the comparison of the model to natural systems rely on: i) the channel planform morphology characterized by the meander wavelength, amplitude, and sinuosity; ii) the channel trajectory and the resulting stratigraphic architecture described using Jobe et al. (2016) indexes. Flumy succeeds in reproducing turbidite channel planform morphology as shown by the mean sinuosity of 1.7, the wavelength to width and amplitude to width ratios around 4 and 1 respectively. First-order meander architecture, characterized by the ratios meander belt width versus channel width, meander belt thickness versus channel depth, and the deduced stratigraphic mobility number (the ratio between lateral versus vertical channel displacements), is also well reproduced: 2.5, 3.8, and 0.6 respectively. Both lateral and downstream channel normalized migrations are around 3.5 times lower than in fluvial systems. All these values are absolutely coherent with the observations. In the other hand, the channel trajectory observed on seismic cross sections (hockey stick geometry) is not fully reproduced: the local stratigraphic mobility number is divided upward by 3 whereas up to 10 is expected. This behavior is generally explained in the literature by an increasing aggradation rate through time and/or flow stripping at outer bend that decreases lateral migration rate (Peakall et al., 2000). These processes are not currently simulated in Flumy, and need to be implemented. This study shows that Flumy model reproduces quite well the first order characteristics observed in the nature and can be used to simulate channelized turbidite reservoirs.

Factors controlling the size and shape of stream channels in coarse noncohesive sands

USGS Publications Warehouse

Wolman, M. Gordon; Brush, Lucien M.

1961-01-01

The size and shape of equilibrium channels in uniform, noncohesive sands, 0.67 mm and 2.0 mm in diameter, were studied experimentally in a laboratory flume 52 feet long in which discharge, slope, sediment load, and bed and bank material could be varied independently. For each run a straight trapezoidal channel was molded in the sand and the flume set at a predetermined slope. Introduction of the discharge was accompanied by widening and aggradation until a stable channel was established. By definition a stable equilibrium existed when channel width, water surface slope, and rate of transport became constant. The duration of individual runs ranged from 2 to 52 hours depending upon the time required for establishing equilibrium. Stability of the banks determined channel shape. In the 2.0 mm sand at a given slope and discharge, only one depth was stable. At this depth the flow was just competent to move particles along the bed of the channel. An increase in discharge produced a wider channel of the same depth and thus transport per unit width remained at a minimum. Channels in the 0.67 mm sand were somewhat more stable and permitted a 1.5 fold increase in depth above that required to start movement of the bed material. An increased transport was associated with the increase in depth. The rate of transport is adequately described in terms of the total shear or in terms of the difference between the total shear and the critical shear required to begin movement. In these experiments the finer, or 0.67 mm, sand, began to move along the bed of the channel at a constant shear stress. Incipient movement of the coarser, or 2.0 mm, sand, varied with the shear stress as well as the mean velocity. At the initiation of movement a lower shear was associated with a higher velocity and vice versa. Anabranches of braided rivers and some natural river channels formed in relatively noncohesive materials resemble the essential characteristics of the flume channels. For a given slope and size of bed material the discharge per unit width in the laboratory channels was similar to that computed for anabranches and river channels measured in the field. Unlike most natural channels, despite impressive bank erosion, the channels in the laboratory only meandered at supercritical flows associated with very steep slopes. These conditions involving shallow depths, high velocity, and steep slopes are uncommon in most natural rivers.

Case study: Equivalent widths of the Middle Rio Grande, New Mexico

Treesearch

Claudia Leon; Pierre Y. Julien; Drew C. Baird

2009-01-01

Successive reaches of the Rio Grande have maintained equivalent channel widths of 50 and 250 m, respectively, over long periods of time. It is hypothesized that alluvial channels adjust bed slope to match the long-term changes in channel width. Analytical relationships show that wider river reaches develop steeper slopes. A modeling approach using daily water and...

Effects of an extreme flood on river morphology (case study: Karoon River, Iran)

NASA Astrophysics Data System (ADS)

Yousefi, Saleh; Mirzaee, Somayeh; Keesstra, Saskia; Surian, Nicola; Pourghasemi, Hamid Reza; Zakizadeh, Hamid Reza; Tabibian, Sahar

2018-03-01

An extreme flood occurred on 14 April 2016 in the Karoon River, Iran. The occurred flood discharge was the highest discharge recorded over the last 60 years in the Karoon River. Using the OLI Landsat images taken on 8 April 2016 (before the flood) and 24 April 2016 (after the flood) the geomorphic effects were detected in different land cover types within the 155-km-long study reach. The results show that the flood significantly affected the channel width and the main effect was high mobilization of channel sediments and severe bank erosion in the meandering reaches. According to field surveys, the flood occupied the channel corridor and even the floodplain parts. However, the channel pattern was not significantly altered, although the results show that the average channel width increased from 192 to 256 m. Statistical results indicate a significant change for active channel width and sinuosity index at 99% confidence level for both indexes. The flood-induced morphological changes varied significantly for different land cover types along the Karoon River. Specifically, the channel has widened less in residential areas than in other land cover types because of the occurrence of bank protection structures. However, the value of bank retreat in residential and protected sides of the Karoon River is more than what we expected during the study of extreme flood.

Riparian vegetation controls on the hydraulic geometry of streams

NASA Astrophysics Data System (ADS)

McBride, M.

2010-12-01

A synthesis of field measurements, remote observations, and numerical modeling techniques highlights the significance of riparian vegetation in determining the geometry of streams and impacting sediment transport dynamics in temperate, Piedmont regions. Specifically, forested and grassy riparian vegetation establish streams with significantly different widths and with different timescales for attaining a state of dynamic equilibrium. The interactions between riparian vegetation, channel form, and channel dynamics are scale dependent. Scale dependency arises because of variations in ratios of vegetation length scales and geomorphic scales (e.g., channel width and depth). Stream reaches with grassy vegetation experience more frequent overbank discharges, migrate more quickly, and exhibit a more classic dynamic equilibrium than forested reaches. These phenomena are relevant to current watershed management efforts that aim to reduce sediment and nutrient loads to receiving water bodies, such as the Chesapeake Bay. The reforestation of riparian buffers is a common restoration technique that intends to improve water quality, temperature regimes, and in-stream physical habitat. Passive reforestation of riparian areas along a tributary to Sleepers River in Danville, VT, USA caused an increase in channel width and cross-sectional area over a 40-year period. From a comparison of historical records and current cross-sectional dimensions, the channel widening resulted in the mobilization of approximately 85 kg/ha/yr of floodplain sediments. Long-term monitoring of suspended sediments in an adjacent watershed indicates that this sediment source may account for roughly 40 percent of the total suspended sediment load. In some instances, increased sediment loads associated with channel widening may be an unforeseen consequence that compromises riparian restoration efforts.

Pool spacing in forest channels

Treesearch

David R. Montgomery; John M. Buffington; Richard D. Smith; Kevin M. Schmidt; George Pess

1995-01-01

Field surveys of stream channels in forested mountain drainage basins in southeast Alaska and Washington reveal that pool spacing depends on large woody debris (LWD) loading and channel type, slope, and width. Mean pool spacing in pool-riffle, plane-bed, and forced pool-riffle channels systematically decreases from greater than 13 channel widths per pool to less than 1...

Relative roughness controls on incipient sediment motion in steep channels

NASA Astrophysics Data System (ADS)

Prancevic, J.; Lamb, M. P.; Fuller, B. M.

2012-12-01

For over eight decades, researchers have noted an appreciable increase in the nondimensional shear stress (Shields number) at initiation of fluvial bedload transport with increasing bed slope. The precise cause of the trend, however, is obscured by the covariance of several factors with increased slope: a greater downstream component of the gravity acting on the grains and fluid, changes in bed morphology, increased grainsize relative to the channel width that may lead to grain bridging, and increased grainsize relative to flow depth (relative roughness) that may change flow hydraulics and particle buoyancy. Here, we report on ongoing laboratory experiments spanning a wide range of bed slopes (2% to 67%) designed to isolate these variables and determine the true cause of heightened critical Shields numbers on steep slopes. First, we eliminated bed morphology as a factor by using only planar beds. To investigate the effect of grain bridging, we used two different channel widths, representing width-to-grainsize ratios of 23:1 and 9:1. Finally, to separate the effects of slope from relative roughness, we compared incipient motion conditions for acrylic particles (submerged specific gravity of 0.15) to natural siliciclastic gravel (submerged specific gravity of 1.65). Different particle densities allowed us to explore incipient motion as a function of relative roughness, independent of channel slope, because lighter particles move at shallower flow depths than heavier ones of the same size. Results show that both materials exhibit a positive trend between bed slope and critical Shields number despite the existence of planar beds for all slopes. Furthermore, changing the grainsize-to-width ratio had a negligible effect on this trend. For all slopes, the critical Shields number for bedload transport was higher for the acrylic particles than for gravel, indicating that relative roughness has a strong control on incipient sediment motion independent of channel slope. These results are consistent with a simple force balance model that considers the effect of relative roughness on flow hydraulics and particle buoyancy, and neglects grain bridging and particle wedging. Together, our results indicate that heightened critical Shields number on steep planar beds is fundamentally due to the increase in relative roughness with increasing slope at the onset of sediment motion.

Amazon floodplain channels regulate channel-floodplain water exchange

NASA Astrophysics Data System (ADS)

Bates, P. D.; Baugh, C.; Trigg, M.

2017-12-01

We examine the role of floodplain channels in regulating the exchange of water between the Amazon main stem and its extensive floodplains using a combination of field survey, remote sensing and numerical modelling for a 30,000 km2 area around the confluence of the Solimões and Purus rivers. From Landsat imagery we identified 1762 individual floodplain channel reaches with total length of nearly 9300 line km that range in width from 900m to 20m. Using a boat survey we measured width and depth along 509 line km of floodplain channels in 45 separate reaches and used these data to develop geomorphic relationships between width and depth. This enabled reconstruction of the depth of all other channels in the Landsat survey to an RMSE of 2.5m. We then constructed a 2D hydraulic model of this site which included all 9300km of floodplain channels as sub-grid scale features using a recently developed version of the LISFLOOD-FP code. The DEM for the model was derived from a version of the SRTM Digital Elevation Model that was processed to remove vegetation artefacts. The model was run at 270m resolution over the entire 30,000 km2 domain for the period from 2002-2009. Simulations were run with and without floodplain channels to examine the impact of these features on floodplain flow dynamics and storage. Simulated floodplain channel hydraulics were validated against a combination of in-situ and remotely sensed data. Our results show that approximately 100 km3 of water is exchanged between the channel and the floodplain during a typical annual cycle, and 8.5±2.1% of mainstem flows is routed through the floodplain. The overall effect of floodplains channels was to increase the duration of connections between the Amazon River and the floodplain. Inclusion of floodplain channels in the model increased inundation volume by 7.3% - 11.3% at high water, and decreased it at low water by 4.0% - 16.6%, with the range in these estimates due to potential errors in floodplain channel geometry. Inundation extent in the model did not increase at high water, but low water flood extents declined by 8.8% - 29.7% due to increased connectivity between the floodplain and the mainstem. The wide range of flow decrease estimates demonstrates that the results are sensitive to errors in the estimation of floodplain channel geometries, particularly bed elevations.

Variation of alluvial-channel width with discharge and character of sediment

USGS Publications Warehouse

Osterkamp, W.R.

1979-01-01

Use of channel measurements to estimate discharge characteristics of alluvial streams has shown that little agreement exists for the exponent of the width-discharge relation. For the equation Q = aWAb, where Q is mean discharge and WA is active-channel width, it is proposed that the exponent, b, should be of fixed value for most natural, perennial, alluvial stream channels and that the coefficient, a, varies with the characteristics of the bed and bank material.Three groups of perennial stream channels with differing characteristics were selected for study using consistent procedures of data collection. A common feature of the groups was general channel stability, that is, absence of excessive widening by erosive discharges. Group 1 consisted of 32 channels of gradient exceeding 0.0080, low suspended-sediment discharge, high channel roughness, and low discharge variability. Group 2 consisted of 13 streams in Kansas having at least 70 percent silt and clay in the bed material and having similar discharge variability, climate, gradient, and riparian vegetation. Group 3, in southern Missouri, consisted of discharge channels of 18 springs having similar conditions of very low discharge variability, climate and vegetation, but variable bed and bank material. Values for the exponent for the three groups of data are 1.98, 1.97, and 1.97, respectively, whereas values of the coefficients are 0.017, 0.042, and 0.011 when discharge is expressed in cubic meters per second and width is in meters. The relation for high-gradient channels (group 1) is supported by published data from laboratory flumes.The similarity of the three values of the exponent demonstrates that a standard exponent of 2.0, significant to two figures, is reasonable for the width-mean discharge relation of perennial, alluvial stream channels, and that the exponent is independent of other variables. Using a fixed exponent of 2.0, a family of simple power-function equations was developed expressing the manner in which channel sediment affects the width-discharge relation.

Downstream variation in bankfull width of wadeable streams across the conterminous United States

EPA Science Inventory

Bankfull channel width is a fundamental measure of stream size and a key parameter of interest for many applications in hydrology, fluvial geomorphology, and stream ecology. We developed downstream hydraulic geometry relationships for bankfull channel width w as a function of dra...

Effect of strained Ge-based NMOSFETs with Ge0.93Si0.07 stressors on device layout

NASA Astrophysics Data System (ADS)

Hsu, Hung-Wen; Lee, Chang-Chun

2017-12-01

This research proposes a germanium (Ge)-based n-channel MOSFET with Ge0.93Si0.07 S/D stressor. A simulation technique is utilized to understand the layout effect of shallow trench isolation (STI) length, gate width, dummy active of diffusion (OD) length, and extended poly width on stress distribution in a channel region. Stress distribution in a channel region was simulated by ANSYS software based on finite element analysis. Furthermore, carrier mobility gain was evaluated by a second-order piezoresistance model. The piezoresistance coefficient of Ge nMOSFET varies from that of Si nMOSFET. The piezoresistance coefficient shows that longitudinal and transverse stresses are the dominant factors affecting the change in electron mobility in the channel region. For Ge-based nMOSFET, longitudinal stress tends to be tensile, whereas transverse stress tends to be compressive. Stress along channel length becomes more tensile when STI length decreases. By contrast, stress along the channel width becomes more compressive when gate width or extended poly width decreases. Electron mobility in Ge-based nMOSFET could be enhanced under the aforementioned conditions. The enhanced electron mobility becomes more significant as the device combines with a contact etching stop layer stressor. Moreover, the mobility can be improved by changing the STI length, gate width, dummy OD length, or extended poly width. This investigation systematically analyzed the relationship between layout factor and stress distribution.

Characterizing Physical Habitat of a Mixed-Land Use Stream of the Central U.S.

NASA Astrophysics Data System (ADS)

Hooper, L. W.; Hubbart, J. A.; Hosmer, G. W.; Hogan, M. L.

2014-12-01

Land use altered flow regime impacts on aquatic biological habitat can be quantified by means of a physical habitat assessment (PHA). PHA metrics include (but are not limited to) channel substrate, width and wetted width, bank slope, and bank height. Hinkson Creek, located in Boone County, Missouri, was placed on the Missouri Department of Natural Resources list of impaired waters (Section 303d) of the Clean Water Act in 1998. A physical habitat assessment of Hinkson Creek in 2014 provides quantitative data characterizing the current potential of Hinkson Creek to fully support aquatic life, specifically macroinvertebrates (a goal for delisting). The PHA was conducted every 100m of Hinkson Creek (56km). Results from the lower 87.9% (contiguous) of the drainage indicate channel width ranged from a maximum of 70m to a minimum of 4.6m, with a mean width of 17m and standard deviation (SD) of 7.4m. Bankfull width ranged from a maximum of 74m to a minimum of 8.8m (mean = 26.1m, SD = 8.2). Bank height ranged from a maximum of 5.8m to a minimum of 0.4m (mean = 2.9m, SD = 1m). Mean bank angle for the left and right banks was nearly equivalent (left = 33.8°, right = 34.6°). Bank height and bankfull width increased with increasing drainage distance. Trench pools were the dominant channel unit at 71.4% of the sample transects, while riffles were present at 16.6%. Analysis of stream channel bed composition was conducted using a modified Wolman pebble count survey at each site and Thalweg profile between sites. Size class results were quantified as follows: 56.1% fines (16mm or less), 36.2% intermediate (16mm to 1000mm, plus vegetation and wood), 8.7% large/bedrock (greater than 1000mm, riprap and bedrock). Study results provide science-based information to better equip land planners in Hinkson Creek watershed and similar multi-use watersheds of the central United States for future management decisions and development scenarios.

Influences of the separation distance, ship speed and channel dimension on ship maneuverability in a confined waterway

NASA Astrophysics Data System (ADS)

Du, Peng; Ouahsine, Abdellatif; Sergent, Philippe

2018-05-01

Ship maneuvering in the confined inland waterway is investigated using the system-based method, where a nonlinear transient hydrodynamic model is adopted and confinement models are implemented to account for the influence of the channel bank and bottom. The maneuvering model is validated using the turning circle test, and the confinement model is validated using the experimental data. The separation distance, ship speed, and channel width are then varied to investigate their influences on ship maneuverability. With smaller separation distances and higher speeds near the bank, the ship's trajectory deviates more from the original course and the bow is repelled with a larger yaw angle, which increase the difficulty of maneuvering. Smaller channel widths induce higher advancing resistances on the ship. The minimum distance to the bank are extracted and studied. It is suggested to navigate the ship in the middle of the channel and with a reasonable speed in the restricted waterway.

Channel movement of meandering Indiana streams

USGS Publications Warehouse

Daniel, James F.

1971-01-01

Because of the consistency of yearly above-average discharge volumes, it was possible to develop a general relation between path-length increase per thousand cubic-feet-per-second-days per square mile of drainage area above average discharge and the width-depth ratio of the channel. Little progress was made toward defining relationships for rotation and translation.

Influence of alluvial cover and lithology on the adjustment characteristics of semi-alluvial bedrock channels

NASA Astrophysics Data System (ADS)

Ferguson, Sean P.; Rennie, Colin D.

2017-05-01

A growing body of research has focused on evaluating the adjustment characteristics of semi-alluvial channels containing proximate bedrock, mixed, and alluvial sections. Active orogens have been the focus of most empirical field-based studies with comparatively less focus on semi-alluvial bedrock channels located in other regions. In this study, we present an inventory of channel geometry data collected from semi-alluvial bedrock channels in Ontario and Québec, Canada, which are not subject to tectonic uplift. Data were sourced from a variety of physiographic settings, permitting evaluation of the influence of alluvial cover, lithology, and gradient on cross-sectional channel form. Our results show no substantial difference in channel width or scaling behaviour amongst bedrock, mixed, and alluvial channels included in our study, except for sedimentary bedrock channels virtually bare of alluvial cover that represent a uniquely wide, distinct subgroup. Channel gradient does not appear to exhibit any observable control on channel width amongst our study rivers, suggesting that sedimentary bedrock channels form a distinct subgroup because of lithology. Comparatively, the widths of our bedrock channels formed in igneous/metamorphic bedrock are comparable to the widths of mixed channels and alluvial channels for a given discharge and drainage area. Our findings also suggest that cross-sectional adjustment of sedimentary bedrock channels is achieved through lateral erosion of the channel banks and downward erosion of the channel bed, whereas cross-sectional adjustment of igneous/metamorphic bedrock is primarily achieved through downward erosion of the bed with limited lateral erosion of the banks.

CHIMNEY FOR BOILING WATER REACTOR

DOEpatents

Petrick, M.

1961-08-01

A boiling-water reactor is described which has vertical fuel-containing channels for forming steam from water. Risers above the channels increase the head of water radially outward, whereby water is moved upward through the channels with greater force. The risers are concentric and the radial width of the space between them is somewhat small. There is a relatively low rate of flow of water up through the radially outer fuel-containing channels, with which the space between the risers is in communication. (AE C)

A novel microfluidic valve controlledby induced charge electro-osmotic flow

NASA Astrophysics Data System (ADS)

Wang, Chengfa; Song, Yongxin; Pan, Xinxiang; Li, Dongqing

2016-07-01

In this paper, a novel microfluidic valve by utilizing induced charge electro-osmotic flow (ICEOF) is proposed and analyzed. The key part of the microfluidic valve is a Y-shaped microchannel. A small metal plate is placed at each corner of the junction of the Y-shaped microchannel. When a DC electrical field is applied through the channels, electro-osmotic flows occur in the channels, and two vortices will be formed near each of the metal plates due to the ICEOF. The two vortices behave like virtual ‘blocking columns’ to restrain and direct the flow in the Y-channel. In this paper, effects of the length of the metal plates, the applied voltages, the width of the microchannel, the zeta potential of the non-metal microchannel wall, and the orientation of the branch channels on the flow switching between two outlet channels are numerically investigated. The results show that the flow switching between the two outlet channels can be flexibly achieved by adjusting the applied DC voltages. The critical switching voltage (CSV), under which one outlet channel is closed, decreases with the increase in the metal plate length and the orientation angle of the outlet channels. The CSV, however, increases with the increase in the inlet voltage, the width of the microchannel, and the absolute value of the zeta potential of the non-metal microchannel wall. Compared with other types of micro-valves, the proposed micro-valve is simple in structure without any moving parts. Only a DC power source is needed for its actuation, thus it can operate automatically by controlling the applied voltages.

Effect of channel size on sweet potato storage root enlargement in the Tuskegee University hydroponic nutrient film system

NASA Technical Reports Server (NTRS)

Morris, Carlton E.; Martinez, Edwin; Bonsi, C. K.; Mortley, Desmond G.; Hill, Walter A.; Ogbuehi, Cyriacus R.; Loretan, Phil A.

1989-01-01

The potential of the sweet potato as a food source for future long term manned space missions is being evaluated for NASA's Controlled Ecological Life Support Systems (CELSS) program. Sweet potatoes have been successfully grown in a specially designed Tuskegee University nutrient film technique (TU NFT) system. This hydroponic system yielded storage roots as high as 1790 g/plant fresh weight. In order to determine the effect of channel size on the yield of sweet potatoes, the width and depth of the growing channels were varied in two separate experiments. Widths were studied using the rectangular TU NFT channels with widths of 15 cm (6 in), 30 cm (12 in) and 45 cm (18 in). Channel depths of 5 cm (2 in), 10 cm (4 in), and 15 cm (6 in) were studied using a standard NASA fan shaped Biomass Production Chamber (BPC) channel. A comparison of preliminary results indicated that, except for storage root number, the growth and yield of sweet potatoes were not affected by channel width. Storage root yield was affected by channel depth although storage root number and foliage growth were not. Both experiments are being repeated.

Characterizing and modelling river channel migration rates at a regional scale: Case study of south-east France.

PubMed

Alber, Adrien; Piégay, Hervé

2017-11-01

An increased awareness by river managers of the importance of river channel migration to sediment dynamics, habitat complexity and other ecosystem functions has led to an advance in the science and practice of identifying, protecting or restoring specific erodible corridors across which rivers are free to migrate. One current challenge is the application of these watershed-specific goals at the regional planning scales (e.g., the European Water Framework Directive). This study provides a GIS-based spatial analysis of the channel migration rates at the regional-scale. As a case study, 99 reaches were sampled in the French part of the Rhône Basin and nearby tributaries of the Mediterranean Sea (111,300 km 2 ). We explored the spatial correlation between the channel migration rate and a set of simple variables (e.g., watershed area, channel slope, stream power, active channel width). We found that the spatial variability of the channel migration rates was primary explained by the gross stream power (R 2  = 0.48) and more surprisingly by the active channel width scaled by the watershed area. The relationship between the absolute migration rate and the gross stream power is generally consistent with the published empirical models for freely meandering rivers, whereas it is less significant for the multi-thread reaches. The discussion focused on methodological constraints for a regional-scale modelling of the migration rates, and the interpretation of the empirical models. We hypothesize that the active channel width scaled by the watershed area is a surrogate for the sediment supply which may be a more critical factor than the bank resistance for explaining the regional-scale variability of the migration rates. Copyright © 2016 Elsevier Ltd. All rights reserved.

The bankfull hydraulic geometry of evolving meander bends

NASA Astrophysics Data System (ADS)

Monegaglia, F.; Tubino, M.; Zolezzi, G.

2017-12-01

Changes in the bankfull hydraulic geometry of meandering rivers associated with meander growth from incipient meandering to cutoffs have seldom been analysed in detail. Such information is also needed by meander morphodynamic models, most of which simulate the evolution of bankfull channel geometry by simply accounting for channel slope reduction inversely proportional to elongation, while changes in bankfull channel width are often neglected or, when they are considered, they are not consistent with the few available observations. To address these gaps we first perform an extensive, systematic, bend-scale evolutionary analysis of bankfull channel widths in several large meandering rivers in the Amazon basin, over a three decades time period, from remotely sensed field data. The analysis consistently show a slight decreasing trend of the bankfull channel width during the planform evolution towards cutoff. Furthermore, we develop a physically based model for the evolution of bankfull channel geometry during the planform development of meandering rivers. The model is based on the conservation of sediment discharge. An integrated one-dimensional Exner equation that accounts for meander elongation, sediment supply conservation and sediment income from the channel banks, allows us to predict the evolution of the channel slope. The evolution of the channel width is modeled through a threshold equation. The model correctly predicts the slight variability of channel width during meander development and a gentler reduction of the channel slope, which is mitigated by the conservation of sediment supply. The bankfull geometry of highly dynamic meandering rivers is predicted to be elongation-dominated, while the one related to slowly evolving meandering rivers is sediment supply-dominated. Finally, we discuss the implications of the proposed modeling framework in terms of planform structure, meander shape and morphodynamic influence.

Method of forming a variable width channel

NASA Technical Reports Server (NTRS)

Andrews, James T. (Inventor)

1989-01-01

A method of forming a channel of varying width in a body comprises the steps of forming a plurality of masking elements having an opening therethrough intersecting a plurality of the elements on a surface of the body, partially flowing the elements into the opening to form a masking pattern having a variable width opening therethrough, and removing portions of the exposed body to form the channel with a sidewall having a surface contour corresponding to an edge of the masking pattern.

Evolution of channel morphology in a large river subject to rectification

NASA Astrophysics Data System (ADS)

Scorpio, Vittoria; Mastronunzio, Marco; Proto, Matteo; Zen, Simone; Bertoldi, Walter; Prà, Elena Dai; Comiti, Francesco; Surian, Nicola; Zolezzi, Guido

2016-04-01

Many large rivers in Europe have been subject to heavy modifications for land reclamation and flood mitigation through centuries. As a consequence, the study of the pre-alteration morphological patterns and of the related channel evolution following the anthropic modifications is rather challenging. The Adige River is the second longest river in Italy and drains 12,100 km2 of the Eastern Italian Alps. Currently, it features a straight to sinuous pattern and an average channel width of 40-60 m. A massive rectification scheme aiming at land reclamation of the Adige valley bottom was planned in the late 18th century, and implemented starting in the first decades of 19th century. Nowadays, it can be considered one of the most altered rivers in Italy, not only due to channelization but also to the presence of many hydropower reservoirs and check-dams along its tributaries. This study aims to the reconstruction of the Adige River's evolutionary trajectory over the last 250 years, and comprehension of key control factors driving channel evolution. A multi-temporal analysis of historical maps and orthophotos from 1776, to 2006 was performed in order to assess channel modifications. In addition, land use changes at the basin scale, years of occurrence of most relevant flood events, and climate variability over the investigated period were analyzed. The detailed topographical map surveyed in 1803 was taken as a reference, and the study sector (115 km long) was divided into 39 reaches. Active channel, bars, riparian vegetation and channel control works were geo-processed. Results show that the Adige River suffered the most intense alteration from 1803 to 1855, and especially from 1847 to 1855. During this period channel narrowing ranged from 14% to 70%, coupled with pattern changes and decreases in the braiding, sinuosity and anabrancing indices. Most important alterations occurred in the reaches presenting a multi-thread morphology in 1803, as their average width declined from 220 m to 110 m. On the contrary, reaches originally sinuous remained quite stable, decreasing from 100 m to 95 m. Overall, relevant channel morphology modifications took place by 1855, when channel configuration had shifted from alternating longitudinal sequences of multi-thread and single-thread, at the beginning of the 19th century, to mainly single-thread. Total length of multi-thread reaches shifted from 31% in 1805, to 22% in 1847, to 8% in the 1855. On the contrary, sinuous and straight patterns increased from 26% (in 1803) to 62% (in 1847), up to 77% of the whole studied river length in 1855. Nevertheless, overall increases in channel braiding and mean channel width was observed downstream of the confluences with the main tributaries. Analysis of the evolutionary trajectory of channel morphology and of controlling factors, shows that human disturbances have largely prevailed over climatic influences in constraining the Adige's dynamics and morphology, mainly because of channelization causing sharp changes in channel pattern and width that occurred during the 19th century.

Impact of a large flood on mountain river habitats, channel morphology, and valley infrastructure

NASA Astrophysics Data System (ADS)

Hajdukiewicz, Hanna; Wyżga, Bartłomiej; Mikuś, Paweł; Zawiejska, Joanna; Radecki-Pawlik, Artur

2016-11-01

The Biała River, Polish Carpathians, was considerably modified by channelization and channel incision in the twentieth century. To restore the Biała, establishing an erodible corridor was proposed in two river sections located in its mountain and foothill course. In these sections, longer, unmanaged channel reaches alternate with short, channelized reaches; and channel narrowing and incision increases in the downstream direction. In June 2010 an 80-year flood occurred on the river; and this study aims at determining its effects on physical habitat conditions for river biota, channel morphology, and valley-floor infrastructure. Surveys of 10 pairs of closely located, unmanaged and channelized cross sections, performed in 2009 and in the late summer 2010, allowed us to assess the flood-induced changes to physical habitat conditions. A comparison of channel planforms determined before (2009) and after (2012) the flood provided information on the degree of channel widening as well as changes in the width of particular elements of the river's active zone in eight stretches of the Biała. The impact of the flood on valley-floor infrastructure was confronted with the degree of river widening in unmanaged and channelized river reaches. Before the flood, unmanaged cross sections were typified by finer bed material and greater lateral variability in depth-averaged and near-bed flow velocity than channelized cross sections. The flood tended to equalize habitat conditions in both types of river cross sections, obliterating differences (in particular physical habitat parameters) between channelized and unmanaged channel reaches. River widening mostly reflected an increase in the area of channel bars, whereas the widening of low-flow channels was less pronounced. A comparison of channel planform from 2009 and 2012 indicated that intense channel incision typical of downstream sections limited river widening by the flood. Active channel width increased by half in the unmanaged cross sections and by one-third in the channelized cross sections. However, damage to the valley-floor infrastructure was practically limited to the channelized river reaches with reinforced channel banks. This indicates incompetent management of riparian areas rather than the degree of river widening as a principal reason for the economic losses during the flood.

Contraction rate, flow modification and bed layering impact on scour at the elliptical guide banks

NASA Astrophysics Data System (ADS)

Gjunsburgs, B.; Jaudzems, G.; Bizane, M.; Bulankina, V.

2017-10-01

Flow contraction by the bridge crossing structures, intakes, embankments, piers, abutments and guide banks leads to general scour and the local scour in the vicinity of the structures. Local scour is depending on flow, river bed and structures parameters and correct understanding of the impact of each parameter can reduce failure possibility of the structures. The paper explores hydraulic contraction, the discharge redistribution between channel and floodplain during the flood, local flow modification and river bed layering on depth, width and volume of scour hole near the elliptical guide banks on low-land rivers. Experiments in a flume, our method for scour calculation and computer modelling results confirm a considerable impact of the contraction rate of the flow, the discharge redistribution between channel and floodplain, the local velocity, backwater and river bed layering on the depth, width, and volume of scour hole in steady and unsteady flow, under clear water condition. With increase of the contraction rate of the flow, the discharge redistribution between channel and floodplain, the local velocity, backwater values, the scour depth increases. At the same contraction rate, but at a different Fr number, the scour depth is different: with increase in the Fr number, the local velocity, backwater, scour depth, width, and volume is increasing. Acceptance of the geometrical contraction of the flow, approach velocity and top sand layer of the river bed for scour depth calculation as accepted now, may be the reason of the structures failure and human life losses.

River meanders and channel size

USGS Publications Warehouse

Williams, G.P.

1986-01-01

This study uses an enlarged data set to (1) compare measured meander geometry to that predicted by the Langbein and Leopold (1966) theory, (2) examine the frequency distribution of the ratio radius of curvature/channel width, and (3) derive 40 empirical equations (31 of which are original) involving meander and channel size features. The data set, part of which comes from publications by other authors, consists of 194 sites from a large variety of physiographic environments in various countries. The Langbein-Leopold sine-generated-curve theory for predicting radius of curvature agrees very well with the field data (78 sites). The ratio radius of curvature/channel width has a modal value in the range of 2 to 3, in accordance with earlier work; about one third of the 79 values is less than 2.0. The 40 empirical relations, most of which include only two variables, involve channel cross-section dimensions (bankfull area, width, and mean depth) and meander features (wavelength, bend length, radius of curvature, and belt width). These relations have very high correlation coefficients, most being in the range of 0.95-0.99. Although channel width traditionally has served as a scale indicator, bankfull cross-sectional area and mean depth also can be used for this purpose. ?? 1986.

Morphodynamics structures induced by variations of the channel width

NASA Astrophysics Data System (ADS)

Duro, Gonzalo; Crosato, Alessandra; Tassi, Pablo

2014-05-01

In alluvial channels, forcing effects, such as a longitudinally varying width, can induce the formation of steady bars (Olesen, 1984). The type of bars that form, such as alternate, central or multiple, will mainly depend on the local flow width-to-depth ratio and on upstream conditions (Struiksma et al., 1985). The effects on bar formation of varying the channel width received attention only recently and investigations, based on flume experiments and mathematical modelling, are mostly restricted to small longitudinal sinusoidal variations of the channel width (e.g. Repetto et al., 2002; Wu and Yeh, 2005, Zolezzi et al., 2012; Frascati and Lanzoni, 2013). In this work, we analyze the variations in equilibrium bed topography in a longitudinal width-varying channel with characteristic scales of the Waal River (The Netherlands) using two different 2D depth-averaged morphodynamic models, one based on the Delft3D code and one on Telemac-Mascaret system. In particular, we explore the effects of changing the wavelength of sinusoidal width variations in a straight channel, focusing on the effects of the spatial lag between bar formation and forcing that is observed in numerical models and laboratory experiments (e.g. Crosato et al, 2011). We extend the investigations to finite width variations in which longitudinal changes of the width-to-depth ratio are such that they may affect the type of bars that become unstable (alternate, central or multiple bars). Numerical results are qualitatively validated with field observations and the resulting morphodynamic pattern is compared with the physics-based predictor of river bar modes by Crosato and Mosselman (2009). The numerical models are finally used to analyse the experimental conditions of Wu and Yeh (2005). The study should be seen as merely exploratory. The aim is to investigate possible approaches for future research aiming at assessing the effects of artificial river widening and narrowing to control bar formation in alluvial rivers. References Crosato A. and Mosselman E., 2009. Simple physics-based predictor for the number of river bars and the transition between meandering and braiding. Water Resources Research, 45, W03424, doi: 10.1029/2008WR007242. Crosato A., Mosselman E., Desta F.B. and Uijttewaal W.S.J., 2011. Experimental and numerical evidence for intrinsic nonmigrating bars in alluvial channels. Water Resources Research, AGU, 47(3), W03511, doi 10.1029/2010WR009714. Frascati A. and Lanzoni S., 2013. A mathematical model for meandering rivers with varying width. J. Geophys. Res.Earth Surf., 118, doi:10.1002/jgrf.20084. Olesen K.W., 1984. Alternate bars in and meandering of alluvial rivers. In: River Meandering, Proc. of the Conf. Rivers '83, 24-26 Oct. 1983, New Orleans, Louisiana, U.S.A., ed. Elliott C.M., pp. 873-884, ASCE, New York. ISBN 0-87262-393-9. Repetto R., Tubino, M. and Paola C., 2002. Planimetric instability of channels with variable width. J. Fluid Mech., 457, 79-109. Struiksma N., Olesen K.W., Flokstra C. and De Vriend H.J., 1985. Bed deformation in curved alluvial channels. J. Hydraul. Res., 23(1), 57- 79. Wu F.-C. and Yeh T.-H., 2005. Forced bars induced by variations of channel width: Implications for incipient bifurcation. J. Geophys. Res., 110, F02009, doi:10.1029/2004JF000160. Zolezzi, G., R. Luchi, and M. Tubino (2012), Modeling morphodynamic processes in meandering rivers with spatial width variations, Rev. Geophys., 50, RG4005, doi:10.1029/2012RG000392.

Electrothermal DC characterization of GaN on Si MOS-HEMTs

NASA Astrophysics Data System (ADS)

Rodríguez, R.; González, B.; García, J.; Núñez, A.

2017-11-01

DC characteristics of AlGaN/GaN on Si single finger MOS-HEMTs, for different gate geometries, have been measured and numerically simulated with substrate temperatures up to 150 °C. Defect density, depending on gate width, and thermal resistance, depending additionally on temperature, are extracted from transfer characteristics displacement and the AC output conductance method, respectively, and modeled for numerical simulations with Atlas. The thermal conductivity degradation in thin films is also included for accurate simulation of the heating response. With an appropriate methodology, the internal model parameters for temperature dependencies have been established. The numerical simulations show a relative error lower than 4.6% overall, for drain current and channel temperature behavior, and account for the measured device temperature decrease with the channel length increase as well as with the channel width reduction, for a set bias.

Using LandSat and SRTM datasets to develop relationships for estimating bankfull channel widths in the Amazon Basin

NASA Astrophysics Data System (ADS)

Gummadi, V.; He, Y.; Beighley, E. R.

2007-12-01

Modeling fine scale spatial and temporal processes of the hydrologic cycle over continental to global extents is vital for assessing the potential impacts of climate and land use change on global water resources and related systems. Significant advancement in understanding and predicting the magnitude, trend, timing and partitioning of terrestrial water stores and fluxes requires the development of methodologies and knowledge for extracting representative hydraulic geometries from remote sensing data products and field data, suitable for estimating inundation characteristics and water storage changes which are limited for much of the globe. In this research, relationships between channel and floodplain widths and spatial drainage characteristics are developed for the Amazon Basin. Channel and floodplain widths were measured using SRTM data and LandSat TM/ETM imagery at 510 sites. The study sites were selected based on the Pfafstetter decomposition methodology which provides an irregular model grid based on repeatedly subdividing landscape units into nine subunits consisting of basins and interbasins. The selected sites encompass all possible combinations of Pfafstetter modeling units (ex., basins of interbasins, interbasins of basins, etc.). The 510 study sites are within the Amazon Basin with drainage areas ranging 10 to 5.4 million sq km and mean watershed ground slopes ranging from 0.4 and 30 percent. Preliminary results indicate that channel widths can be predicted using drainage area and mean watershed slope (R2 = 0.85). Floodplain widths can be predicted using channel width and the local slope (R2 = 0.70). Using the Purus watershed, a sub-basin to the Amazon (350,000 sq km), effects of channel and floodplain widths on simulated hydrographs are presented.

Errors in Martian paleodischarges skew interpretations of hydrologic history: Case study of the Aeolis Dorsa, Mars, with insights from the Quinn River, NV

NASA Astrophysics Data System (ADS)

Jacobsen, Robert E.; Burr, Devon M.

2018-03-01

Changes in Martian fluvial geomorphology with time-stratigraphic age, including decreases in paleochannel widths, suggest waning paleodischarges through time. Where fluvial landforms do not preserve paleochannel widths (e.g., meander deposits), other landform dimensions (i.e., radius of curvature) may be used to estimate paleodischarges. In the Aeolis Dorsa region, topographically inverted and stacked fluvial deposits - wide meander point bars overlain by thin channel fills - preserve ostensible evidence of decreasing paleodischarges through time. However, a robust paleohydraulic analysis of these distinct deposits requires knowledge of the accuracy of a terrestrial-based empirical relationship that estimates channel width from point-bar radius of curvature. We assess the accuracy of this radius-width relationship by applying it to a well-studied terrestrial analog, the Quinn River, Nevada. We find that radii of curvature from the Quinn River exceed the values predicted from the empirical relationship. These anomalously high radii are associated with greater resistance in the channel cut banks, indicating that bank strength is a confounding factor in the radius-width relationship. Some deposits in the Aeolis Dorsa include irregular meander morphologies, suggesting variably resistant channel banks and overestimates of both paleochannel widths and paleodischarges. Furthermore, the morphometry of the overlying thin channel fills suggests their widths have been eroded, such that their paleodischarges are underestimates. These overestimates and underestimates, when considered together, suggest little change in paleodischarge during the stratigraphic transition from meander deposits to channel fills. This work demonstrates the importance of terrestrial analog studies for revealing confounding factors in Martian fluvial systems and cautions against simplistic interpretations of Martian fluvial history. The discovered inaccuracies of paleodischarge estimates expose sources of uncertainty in the extant paleodischarge data that bias inferences toward waning hydrologic activity through time.

Hydraulic Geometry Characteristics of Continuous-Record Streamflow-Gaging Stations on Four Urban Watersheds Along the Main Stem of Gwynns Falls, Baltimore County and Baltimore City, Maryland

USGS Publications Warehouse

Doheny, Edward J.; Fisher, Gary T.

2007-01-01

Four continuous-record streamflow-gaging stations are currently being operated by the U.S. Geological Survey on the main stem of Gwynns Falls in western Baltimore County and Baltimore City, Maryland. The four streamflow-gaging stations drain urban or suburban watersheds with significantly different drainage areas. In addition to providing continuous- record discharge data at these four locations, operation of these stations also provides a long-term record of channel geometry variables such as cross-sectional area, channel width, mean channel depth, and mean velocity that are obtained from physical measurement of the discharge at a variety of flow conditions. Hydraulic geometry analyses were performed using discharge-measurement data from four continuous-record streamflow-gaging stations on the main stem of Gwynns Falls. Simple linear regression was used to develop relations that (1) quantify changes in cross-sectional area, channel width, mean channel depth, and mean velocity with changes in discharge at each station, and (2) quantify changes in these variables in the Gwynns Falls watershed with changes in drainage area and annual mean discharge. Results of the hydraulic geometry analyses indicated that mean velocity is more responsive to changes in discharge than channel width and mean channel depth for all four streamflow-gaging stations on the main stem of Gwynns Falls. For the two largest and most developed watersheds, on Gwynns Falls at Villa Nova, and Gwynns Falls at Washington Boulevard at Baltimore, the slope of the regression lines, or hydraulic exponents, indicated that mean velocity was more responsive to changes in discharge than any of the other hydraulic variables that were analyzed. This was true even when considering changes in cross-sectional area with discharge, which incorporates the combined effects of channel width and mean channel depth. A comparison of hydraulic exponents for Gwynns Falls to average values from previous work indicated that the velocity exponents for all four stations on the Gwynns Falls are larger than the average value of 0.34. For stations 01589300 and 01589352, the exponents for mean velocity are about twice as large as the average value. Analyses of cross-sectional area, channel width, mean channel depth, and mean velocity in conjunction with changes in drainage area and annual mean discharge indicated that channel width is much more responsive to changes in drainage area and annual mean discharge than are mean channel depth or mean velocity. Cross-sectional area, which combines the effects of channel width and mean channel depth, was also found to be highly responsive to changes in drainage area and annual mean discharge.

Relationships of elevation, channel slope, and stream width to occurrences of native fishes at the Great Plains-Rocky Mountains interface

USGS Publications Warehouse

Brunger, Lipsey T.S.; Hubert, W.A.; Rahel, F.J.

2005-01-01

Environmental gradients occur with upstream progression from plains to mountains and affect the occurrence of native warmwater fish species, but the relative importance of various environmental gradients are not defined. We assessed the relative influences of elevation, channel slope, and stream width on the occurrences of 15 native warmwater fish species among 152 reaches scattered across the North Platte River drainage of Wyoming at the interface of the Great Plains and Rocky Mountains. Most species were collected in reaches that were lower in elevation, had lower channel slopes, and were wider than the medians of the 152 sampled reaches. Several species occurred over a relatively narrow range of elevation, channel slope, or stream width among the sampled reaches, but the distributions of some species appeared to extend beyond the ranges of the sampled reaches. We identified competing logistic-regression models that accounted for the occurrence of individual species using the information-theoretic approach. Linear logistic-regression models accounted for patterns in the data better than curvilinear models for all species. The highest ranked models included channel slope for seven species, elevation for six species, stream width for one species, and both channel slope and stream width for one species. Our results suggest that different environmental gradients may affect upstream boundaries of different fish species at the interface of the Great Plains and Rocky Mountains in Wyoming.

Supersonic cavity flows over concave and convex walls

NASA Astrophysics Data System (ADS)

Ye, A. Ran; Das, Rajarshi; Setoguchi, Toshiaki; Kim, Heuy Dong

2016-04-01

Supersonic cavity flows are characterized by compression and expansion waves, shear layer, and oscillations inside the cavity. For decades, investigations into cavity flows have been conducted, mostly with flows at zero pressure gradient entering the cavity in straight walls. Since cavity flows on curved walls exert centrifugal force, the features of these flows are likely to differ from those of straight wall flows. The aim of the present work is to study the flow physics of a cavity that is cut out on a curved wall. Steady and unsteady numerical simulations were carried out for supersonic flow through curved channels over the cavity with L/H = 1. A straight channel flow was also analyzed which serves as the base model. The velocity gradient along the width of the channel was observed to increase with increasing the channel curvature for both concave and convex channels. The pressure on the cavity floor increases with the increase in channel curvature for concave channels and decreases for convex channels. Moreover, unsteady flow characteristics are more dependent on channel curvature under supersonic free stream conditions.

Modeling fluvial incision and transient landscape evolution: Influence of dynamic channel adjustment

NASA Astrophysics Data System (ADS)

Attal, M.; Tucker, G. E.; Whittaker, A. C.; Cowie, P. A.; Roberts, G. P.

2008-09-01

Channel geometry exerts a fundamental control on fluvial processes. Recent work has shown that bedrock channel width depends on a number of parameters, including channel slope, and is not solely a function of drainage area as is commonly assumed. The present work represents the first attempt to investigate the consequences of dynamic, gradient-sensitive channel adjustment for drainage-basin evolution. We use the Channel-Hillslope Integrated Landscape Development (CHILD) model to analyze the response of a catchment to a given tectonic perturbation, using, as a template, the topography of a well-documented catchment in the footwall of an active normal fault in the Apennines (Italy) that is known to be undergoing a transient response to tectonic forcing. We show that the observed transient response can be reproduced to first order with a simple detachment-limited fluvial incision law. Transient landscape is characterized by gentler gradients and a shorter response time when dynamic channel adjustment is allowed. The differences in predicted channel geometry between the static case (width dependent solely on upstream area) and dynamic case (width dependent on both drainage area and channel slope) lead to contrasting landscape morphologies when integrated at the scale of a whole catchment, particularly in presence of strong tilting and/or pronounced slip-rate acceleration. Our results emphasize the importance of channel width in controlling fluvial processes and landscape evolution. They stress the need for using a dynamic hydraulic scaling law when modeling landscape evolution, particularly when the relative uplift field is nonuniform.

Analysis of equivalent widths of alluvial channels and application for instream habitat in the Rio Grande

Treesearch

Claudia A. Leon

2003-01-01

Rivers are natural systems that adjust to variable water and sediment discharges. Channels with spatial variability in width that are managed to maintain constant widths over a period of time are able to transport the same water and sediment discharges by adjusting the bed slope. Methods developed to de ne equilibrium hydraulic geometry characteristics of alluvial...

Stabilization of a gravel channel by large streamside obstructions and bedrock bends, Jacoby Creek, northwestern California

Treesearch

Thomas E. Lisle

1996-01-01

Abstract - Jacoby Creek (bed width =12 m; bankfull discharge = 32.6 m 3 /s) contains stationary gravel bars that have forms and positions controlled by numerous large streamside obstructions (bedrock outcrops, large woody debris, and rooted bank projections) and bedrock bends. Bank-projection width and bar volume measured in 104 channel segments 1 bed-width long are...

Sorting Out Effects of Active Stream Restoration: Channel Morphology, Channel Change Processes and Potential Controls

NASA Astrophysics Data System (ADS)

McDowell, P. F.

2017-12-01

In many active restoration projects, instream structures or modifications are designed to produce specific change in channel form, such as reduced W:D or increased pool depth, yet there is little monitoring to evaluate effectiveness. Active restoration often takes place within a context of other land management changes that can have an effect on channel form. Thus, the effects of active restoration are difficult to separate from the effects of other management actions. We measured morphologic response to restoration designs on sections of the Middle Fork John Day River, a gravel-cobble bed river under a cattle grazing regime in the Blue Mountain of Oregon. Since 2000, restoration actions have included elimination of cattle grazing in the riparian zone (passive restoration), riparian planting of woody vegetation, instream log structures for fish habitat and pool maintenance, and elimination of a major flow diversion. We listed the hypothetical effects of each of these management changes, showing overlap among effects of active and passive restoration. Repeat cross-section and longitudinal profile surveys over eight years, and repeat aerial imagery, documented changes in channel width, depth and bed morphology, and processes of change (bank erosion or aggradation, point bar erosion or aggradation, bed incision or aggradation), in two restored reaches and two adjacent control (unrestored) reaches. Morphologic changes were modest. Bankfull cross-section area, width, and W:D all decreased slightly in both restored reaches. Control reaches were unchanged or increased slightly. Processes of change were markedly different among the four reaches, with different reaches dominated by different processes. One restored reach was dominated by slight bed aggradation, increased pool depth and deep pools/km, while the other restored reach was dominated by bank erosion, bar aggradation and slight bed incision, along with increased deep pools/km. The longitudinal profile showed significant re-arrangement of bed morphology. The spatial context of processes and controls allows some separation of the effectiveness of different management actions. Active restoration directly increased pool depth, but passive restoration apparently had more impact on aggradation/degradation and width.

Contributions of moderately low flows and large floods to geomorphic change in the Rio Puerco Arroyo, New Mexico

USGS Publications Warehouse

Griffin, Eleanor R.; Friedman, Jonathan M.

2016-01-01

Abstract—From the mid-1800s to around 1930, monsoonal floods incised an arroyo roughly 100 m wide and 10 m deep along the lower Rio Puerco, NM, from the confluence with the Rio San Jose downstream to the mouth at the Rio Grande, causing sedimentation and flooding downstream. Since the 1930s, the channel has greatly narrowed, a densely vegetated floodplain has developed, the arroyo has partly filled, and downstream sedimentation has greatly decreased. Application of herbicide to a 12-km reach of the arroyo in 2003 to control non-native saltcedar (Tamarix spp.) prompted ongoing studies of channel change in the presence and absence of dense, riparian, woody vegetation. We used digital terrain models and satellite imagery to quantify changes in channel width and location in the sprayed reach and in an unsprayed reach downstream during a moderately low-flow interval (November 2006 to March 2010) and during an interval with a large flood (March 2010 to January/February 2014). Channel width increased in magnitude and variability in the sprayed reach but not in the unsprayed reach over both intervals, continuing a pattern first observed in an earlier study of the period 2003 to 2006. Since the herbicide application in 2003, there have been a total of five meander cutoffs in the sprayed reach and none in the unsprayed reach. In kilometer-long sections of the sprayed reach, channel width is now approaching that at the beginning of the period of channel narrowing in 1935.

Using Geomorphic Change Detection to Understand Restoration Project Success Relative to Stream Size

NASA Astrophysics Data System (ADS)

Yeager, A.; Segura, C.

2017-12-01

Large wood (LW) jams have long been utilized as a stream restoration strategy to create fish habitat, with a strong focus on Coho salmon in the Pacific Northwest. These projects continue to be implemented despite limited understanding of their success in streams of different size. In this study, we assessed the changes triggered by LW introductions in 10 alluvial plane bed reaches with varying drainage areas (3.9-22 km²) and bankfull widths (6.4-14.7 m) in one Oregon Coast Range basin. In this basin, LW was added in an effort to improve winter rearing habitat for Coho salmon. We used detailed topographic mapping (0.5 m² resolution) to describe the local stream and floodplain geometry. Pebble counts were used to monitor changes in average substrate size after the LW addition. Field surveys were conducted immediately after the LW were installed, in the summer of 2016, and one year after installation, in the summer of 2017. We used geomorphic change detection analysis to quantify the amount of scour and deposition at each site along with changes in average bankfull width. Then we determined the relative amount of change among all sites to identify which size stream changed the most. We also modeled fluctuations in water surface elevation at each site, correlating frequency and inundation of the LW with geomorphic changes detected from the topographic surveys. Preliminary results show an increase in channel width and floodplain connectivity at all sites, indicating an increase in off-channel habitat for juvenile Coho salmon. Bankfull widths increased up to 75% in small sites and up to 25% in large sites. Median grain size became coarser in large streams (increased up to 20%), while we saw a similar amount of fining at smaller sites. The overall increase in channel width is compensated by an overall decrease in bed elevation at both large and small sites, suggesting the maintenance of overall geomorphic equilibrium. Further work will include quantifying these geomorphic changes in the context of critical salmon habitat factors. By identifying which size stream changes the most after LW introduction, and linking this change to salmon habitat metrics, we will provide information to aid in optimizing future LW stream restoration efforts that focus on stream reaches likely to experience the greatest increase in fish habitat.

A picoliter-volume mixer for microfluidic analytical systems.

PubMed

He, B; Burke, B J; Zhang, X; Zhang, R; Regnier, F E

2001-05-01

Mixing confluent liquid streams is an important, but difficult operation in microfluidic systems. This paper reports the construction and characterization of a 100-pL mixer for liquids transported by electroosmotic flow. Mixing was achieved in a microfabricated device with multiple intersecting channels of varying lengths and a bimodal width distribution. All channels running parallel to the direction of flow were 5 microm in width whereas larger 27-microm-width channels ran back and forth through the parallel channel network at a 45 degrees angle. The channel network composing the mixer was approximately 10 microm deep. It was observed that little mixing of the confluent solvent streams occurred in the 100-microm-wide, 300-microm-long mixer inlet channel where mixing would be achieved almost exclusively by diffusion. In contrast, after passage through the channel network in the approximately 200-microm-length static mixer bed, mixing was complete as determined by confocal microscopy and CCD detection. Theoretical simulations were also performed in an attempt to describe the extent of mixing in microfabricated systems.

Current conduction in junction gate field effect transistors. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kim, C.

1970-01-01

The internal physical mechanism that governs the current conduction in junction-gate field effect transistors is studied. A numerical method of analyzing the devices with different length-to-width ratios and doping profiles is developed. This method takes into account the two dimensional character of the electric field and the field dependent mobility. Application of the method to various device models shows that the channel width and the carrier concentration in the conductive channel decrease with increasing drain-to-source voltage for conventional devices. It also shows larger differential drain conductances for shorter devices when the drift velocity is not saturated. The interaction of the source and the drain gives the carrier accumulation in the channel which leads to the space-charge-limited current flow. The important parameters for the space-charge-limited current flow are found to be the L/L sub DE ratio and the crossover voltage.

High resolution, high rate X-ray spectrometer

DOEpatents

Goulding, Frederick S.; Landis, Donald A.

1987-01-01

A pulse processing system (10) for use in an X-ray spectrometer in which a ain channel pulse shaper (12) and a fast channel pulse shaper (13) each produce a substantially symmetrical triangular pulse (f, p) for each event detected by the spectrometer, with the pulse width of the pulses being substantially independent of the magnitude of the detected event and with the pulse width of the fast pulses (p) being substantially shorter than the pulse width of the main channel pulses (f). A pile-up rejector circuit (19) allows output pulses to be generated, with amplitudes linearly related to the magnitude of the detected events, whenever the peak of a main channel pulse (f) is not affected by a preceding or succeeding main channel pulse, while inhibiting output pulses wherein peak magnitudes of main channel pulses are affected by adjacent pulses. The substantially symmetrical triangular main channel pulses (f) are generated by the weighted addition (27-31) of successive RC integrations (24, 25, 26) of an RC differentiated step wave (23). The substantially symmetrical triangular fast channel pulses (p) are generated by the RC integration ( 43) of a bipolar pulse (o) in which the amplitude of the second half is 1/e that of the first half, with the RC time constant of integration being equal to one-half the width of the bipolar pulse.

Search for a high-mass Higgs boson decaying to a W boson pair in pp collisions at √s = 8 TeV with the ATLAS detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aad, G.; Aad, G.; Abbott, B.

A search for a high-mass Higgs boson H is performed in the H→WW→ℓνℓν and H→WW→ℓνqq decay channels, using pp collision data corresponding to an integrated luminosity of 20.3 fb -1, collected at √s = 8 TeV by the ATLAS detector at the Large Hadron Collider. No evidence of a high-mass Higgs boson is found. Limits on σ H×BR(H→WW) as a function of the Higgs boson mass mH are determined in three different scenarios: one in which the heavy Higgs boson has a narrow width compared to the experimental resolution, one a width increasing with the boson mass and modeled bymore » the complex-pole scheme following the same behavior as in the Standard Model, and one for intermediate widths. The upper range of the search is m H=1500 GeV for the narrow-width scenario and m H=1000 GeV for the other two scenarios. The lower edge of the search range is 200-300 GeV and depends on the analysis channel and search scenario. For each scenario, individual and combined limits from the two WW decay channels are presented. At mH=1500 GeV, the highest mass point tested, σ H∙BR(H→WW) for a narrow-width Higgs boson is constrained to be less than 22 fb and 6.6 fb at the 95% CL for the gluon fusion and vector-boson fusion production modes, respectively.« less

Channel adjustements over the last century of the Moldova River, Romania

NASA Astrophysics Data System (ADS)

Chiriloaei, F. A.; Radoane, M.; Radoane, N.

2012-04-01

Moldova River is a 205 km long river, right tributary of the Siret River, with the confluence close to Roman city. The most important tributaries are Moldoviţa, Suha Mică, Suha Mare, Râsca, Ozana and Topolita Rivers. The drainage basin area is 4316 km2, a discharge of about 32.8 m3/s and is superimposed on four lithostratigraphic units: the crystalline Mesozoic unit, the flysch unit, the molasse unit and the platform unit. The study reach is 110 km long and is located on the external part of the Eastern-Carpathians at the contact with the Moldavian Plateau. This contact is characterised by a piedmont zone. The high rate of alluviation in this piedmont plain had a decisive role on the spatial and temporal evolution of fluvial forms and processes, expressed in the morphology of alluvial terraces in the valley bottom, the morphology of the active channel, the spatial distribution of bars and secondary channels and lateral migration rates. The morphology of the river in the study reach is dominated by braided and wandering channel patterns. The present (2005) active channel width ranges between 700 and 1000 m. Planform changes of river features over the last 100 years were analyzed on three historical maps (1910, 1960, and 1980) and one orthophoto (2005). Channel width average has significantly decreased in the last century. The Moldova river channel width suffered a strong narrowing, approximately 76% (from 1910 to 2005). So, from a channel width about more than 1200 m, it decreased at about 300 m. We can note two phase of narrowing: a first one - stronger, of 56%, untill 1960 (a reduction of active channel width for about 10.5 m/year) and a second phase, of 35%, after 1960, with a narrowing rate for about 8.8 m/an. The historical trend of braiding index shows a remarkable decrease in the last 50 - 60 years, from 3.2 in 1960, at 2.6 in 1980 and 2.0, in 2005, for all the extra-Carpathian study reach (110 km). There are different situations at local scale, shown using the sectorial analysis. The rates of channel incision were estimated by analyzing the lowest annual stage of the Moldova River, in 4 gauging stations. Along the river, the incision rate (absolute values) increase from - 80 cm (at the exit of mountain area) to - 2.60 m at the confluence with Siret River. In terms of human impact, in-channel gravel mining and local embankments near bridges and towns are the most important direct interventions along the channel. Besides the direct effect of channelization on channel morphology, the major effect of human actions was on sediment regime. A significant decrease of in-channel sediment supply was determined by gravel mining. On the other hand, channel-forming discharges did not undergo significant changes in most of the study streams. It is obvious that, channel with narrowed considerably, river flow concentrated, therefore, the number of channels (links) reduced (from maximum 10, in 1960, to maximum 8 in 1980 and approximately 5, in 2005). In this period, some reaches changed their typology from braided reaches to wandering reaches.

Surprising features of particle dynamics in channel-facilitated transport

NASA Astrophysics Data System (ADS)

Berezhkovskii, Alexander M.; Bezrukov, Sergey M.

2007-06-01

We analyze the consequences of interactions between the pore and the translocating molecule within the framework of a continuous diffusion model using the Smoluchowski equation with the radiation boundary conditions. We describe the solute-pore interaction in terms of the potential of mean force. Several of our analytical findings are quite counterintuitive. Three of the examples to be discussed here are: (i) "Sticking" to the channel slows down translocation (a particle spends more time in the channel) but increases the flux; (ii) If the potential well modeling the particle-channel interaction occupies only a part of the channel length, the average translocation time is non-monotonic in the width of the potential well, first increasing and then decreasing; (iii) At a finite potential bias applied to the channel, the mean "up-hill" and "downhill" particle translocation times (and their distributions) are identical.

Jamming of Monodisperse Cylindrical Grains in Featureless Vertical Channels

NASA Astrophysics Data System (ADS)

Friedl, Nicholas; Baxter, G. William

2014-03-01

We study jamming of low aspect-ratio cylindrical Delrin grains falling through a featureless vertical channel under the influence of gravity. These grains have an aspect-ratio less than two (H/D < 2) and resemble aspirin tablets, 35mm film canisters, poker chips, or coins. Monodisperse grains are allowed to fall under the influence of gravity through a uniform channel of square cross-section where the channel width is greater than the grain size and constant along the length of the channel. No combination of grain heights and diameters is equal to the channel width. Collections of grains sometimes form jams, stable structures in which the grains are supported by the channel walls and not by grains or walls beneath them. The probability of a jam occurring and the jam's strength are influenced by the grain dimensions and channel width. We will present experimental measurements of the jamming probability and jam strength and discuss the relationship of these results to other experiments and theories. Supported by an Undergraduate Research Grant from Penn State Erie, The Behrend College.

Flow, Sediment Supply, and Channel Width Controls on Gravel Bedform Dynamics

NASA Astrophysics Data System (ADS)

Nelson, P. A.; Morgan, J. A.

2017-12-01

Heterogeneous, coarse-grained riverbeds often self-organize into migrating bedforms such as gravel dunes or bedload sheets. It has recently been suggested that sediment supply and the relative mobility of the bed surface sediment affects the type of bedforms that may be present in gravel-bed rivers; however, our understanding of gravel bedform dynamics remains well behind that of bedforms in sandy channels. Here, we present results from flume experiments in which we investigate how the formation and dynamics of gravel bedforms is affected by changes in discharge, sediment supply, and channel geometry. Experiments were conducted in a 1.1-m wide, 18-m long, sediment-feed flume. The initial bed material and the sediment feed mixture was composed of a sediment mixture ranging in size from 0.5-4 mm, with a median value of 3.6 mm. We used two channel geometries (a straight channel and a channel with sinusoidal width variations) and conducted three experimental runs for each geometry: 1) equilibrium sediment supply and steady flow, 2) equilibrium sediment supply and repeated hydrographs, and 3) doubled sediment supply and repeated hydrographs. During the experiments, low-amplitude, migrating bedforms developed and their dynamics were tracked both visually and via collection of repeated structure-from-motion topographic datasets. In the constant-width geometry, bedform amplitudes and migration rates were relatively constant under steady flow, but when subjected to repeated hydrographs the average bedform celerity decreased by about 50% and the amplitude of the bedforms increased and decreased with the changing flow rate. At twice the equilibrium sediment supply, the bedforms organized into an alternating pattern. This pattern was most pronounced at the lower flow rates, and became less stable at the higher discharges of the repeat hydrographs. Preliminary results suggest bedform celerity in the variable width geometry under steady flow and equilibrium sediment supply was half the celerity of the bedforms for the same conditions in the straight-walled geometry. These experiments suggest that variations in discharge, sediment supply, and channel geometry play an important role in the formation and dynamics of bedforms in gravel-bed rivers.

Channel evolution of the Hatchie River near the U.S. Highway 51 crossing in Lauderdale and Tipton counties, West Tennessee

USGS Publications Warehouse

Bryan, B.A.

1989-01-01

An investigation was conducted to describe the channel cross-section evolution near the bridge crossing of the Hatchie River at U.S. Highway 51 in Lauderdale and Tipton Counties, in West Tennessee. The study also included velocity and discharge distributions near the bridge crossing, and definition of streamflow duration and flood frequencies at the bridge site and comparison of these statistics with flows prior to the bridge collapse. Cross-section measurements at the site indicated that the channel was widening at a rate of 0.8 ft/year from 1931 through about 1975. The channel bed was stable at an elevation of about 235 ft. Construction of a south bound bridge in 1974 and 1975 reduced the effective flow width from about 4,000 to about 1,000 ft. Data collected from 1975 to 1981 indicated that the channel bed degraded to an elevation of about 230 ft and the widening rate increased to about 4.5 ft/year. The channel bed returned to approximately the pre-construction elevation of 235 ft as channel width increased. The widening rate decreased to about 1.8 ft/year from 1981 through 1989. Channel-geometry data indicated that recent channel morphology changes along the toe of the right bank have resulted in continued bank undercutting and bank failure. Cross-section geometry and flow-velocity distributions from measurements made from April 6 through 10, 1989, indicate that there is a high-flow meander pattern through this river reach and that the bridges are located at the point where the current strikes the right bank. (USGS)

Correlations for reduced-width amplitudes in /sup 49/V

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chou, B.H.; Mitchell, G.E.; Bilpuch, E.G.

1980-10-13

Measurement of the relative sign of inelastic proton-channel amplitudes permits the determination of amplitude correlations. Data were obtained for 45 5/2/sup +/ resonances in /sup 49/V. Although the reduced widths in each channel followed a Porter-Thomas distribution, large amplitude correlations were observed. The results are compared with the reduced-width--amplitude distribution of Krieger and Porter. This is the first direct test of the Krieger-Porter distribution.

Systematic Onset of Periodic Patterns in Random Disk Packings

NASA Astrophysics Data System (ADS)

Topic, Nikola; Pöschel, Thorsten; Gallas, Jason A. C.

2018-04-01

We report evidence of a surprising systematic onset of periodic patterns in very tall piles of disks deposited randomly between rigid walls. Independently of the pile width, periodic structures are always observed in monodisperse deposits containing up to 1 07 disks. The probability density function of the lengths of disordered transient phases that precede the onset of periodicity displays an approximately exponential tail. These disordered transients may become very large when the channel width grows without bound. For narrow channels, the probability density of finding periodic patterns of a given period displays a series of discrete peaks, which, however, are washed out completely when the channel width grows.

A computer program for analyzing channel geometry

USGS Publications Warehouse

Regan, R.S.; Schaffranek, R.W.

1985-01-01

The Channel Geometry Analysis Program (CGAP) provides the capability to process, analyze, and format cross-sectional data for input to flow/transport simulation models or other computational programs. CGAP allows for a variety of cross-sectional data input formats through use of variable format specification. The program accepts data from various computer media and provides for modification of machine-stored parameter values. CGAP has been devised to provide a rapid and efficient means of computing and analyzing the physical properties of an open-channel reach defined by a sequence of cross sections. CGAP 's 16 options provide a wide range of methods by which to analyze and depict a channel reach and its individual cross-sectional properties. The primary function of the program is to compute the area, width, wetted perimeter, and hydraulic radius of cross sections at successive increments of water surface elevation (stage) from data that consist of coordinate pairs of cross-channel distances and land surface or channel bottom elevations. Longitudinal rates-of-change of cross-sectional properties are also computed, as are the mean properties of a channel reach. Output products include tabular lists of cross-sectional area, channel width, wetted perimeter, hydraulic radius, average depth, and cross-sectional symmetry computed as functions of stage; plots of cross sections; plots of cross-sectional area and (or) channel width as functions of stage; tabular lists of cross-sectional area and channel width computed as functions of stage for subdivisions of a cross section; plots of cross sections in isometric projection; and plots of cross-sectional area at a fixed stage as a function of longitudinal distance along an open-channel reach. A Command Procedure Language program and Job Control Language procedure exist to facilitate program execution on the U.S. Geological Survey Prime and Amdahl computer systems respectively. (Lantz-PTT)

Bar dimensions and bar shapes in estuaries

NASA Astrophysics Data System (ADS)

Leuven, Jasper; Kleinhans, Maarten; Weisscher, Steven; van der Vegt, Maarten

2016-04-01

Estuaries cause fascinating patterns of dynamic channels and shoals. Intertidal sandbars are valuable habitats, whilst channels provide access to harbors. We still lack a full explanation and classification scheme for the shapes and dimensions of bar patterns in natural estuaries, in contrast with bars in rivers. Analytical physics-based models suggest that bar length in estuaries increases with flow velocity, tidal excursion length or estuary width, depending on which model. However, these hypotheses were never validated for lack of data and experiments. We present a large dataset and determine the controls on bar shape and dimensions in estuaries, spanning bar lengths from centimeters (experiments) to 10s of kilometers length. First, we visually identified and classified 190 bars, measured their dimensions (width, length, height) and local braiding index. Data on estuarine geometry and tidal characteristics were obtained from governmental databases and literature on case studies. We found that many complex bars can be seen as simple elongated bars partly cut by mutually evasive ebb- and flood-dominated channels. Data analysis shows that bar dimensions scale with estuary dimensions, in particular estuary width. Breaking up the complex bars in simple bars greatly reduced scatter. Analytical bar theory overpredicts bar dimensions by an order of magnitude in case of small estuarine systems. Likewise, braiding index depends on local width-to-depth ratio, as was previously found for river systems. Our results suggest that estuary dimensions determine the order of magnitude of bar dimensions, while tidal characteristics modify this. We will continue to model bars numerically and experimentally. Our dataset on tidal bars enables future studies on the sedimentary architecture of geologically complex tidal deposits and enables studying effects of man-induced perturbations such as dredging and dumping on bar and channel patterns and habitats.

Nanowire size dependence on sensitivity of silicon nanowire field-effect transistor-based pH sensor

NASA Astrophysics Data System (ADS)

Lee, Ryoongbin; Kwon, Dae Woong; Kim, Sihyun; Kim, Sangwan; Mo, Hyun-Sun; Kim, Dae Hwan; Park, Byung-Gook

2017-12-01

In this study, we investigated the effects of nanowire size on the current sensitivity of silicon nanowire (SiNW) ion-sensitive field-effect transistors (ISFETs). The changes in on-current (I on) and resistance according to pH were measured in fabricated SiNW ISFETs of various lengths and widths. As a result, it was revealed that the sensitivity expressed as relative I on change improves as the width decreases. Through technology computer-aided design (TCAD) simulation analysis, the width dependence on the relative I on change can be explained by the observation that the target molecules located at the edge region along the channel width have a stronger effect on the sensitivity as the SiNW width is reduced. Additionally, the length dependence on the sensitivity can be understood in terms of the resistance ratio of the fixed parasitic resistance, including source/drain resistance, to the varying channel resistance as a function of channel length.

Transport properties and device-design of Z-shaped MoS2 nanoribbon planar junctions

NASA Astrophysics Data System (ADS)

Zhang, Hua; Zhou, Wenzhe; Liu, Qi; Yang, Zhixiong; Pan, Jiangling; Ouyang, Fangping; Xu, Hui

2017-09-01

Based on MoS2 nanoribbons, metal-semiconductor-metal planar junction devices were constructed. The electronic and transport properties of the devices were studied by using density function theory (DFT) and nonequilibrium Green's functions (NEGF). It is found that a band gap about 0.4 eV occurs in the planar junction. The electron and hole transmissions of the devices are mainly contributed by the Mo atomic orbitals. The electron transport channel is located at the edge of armchair MoS2 nanoribbon, while the hole transport channel is delocalized in the channel region. The I-V curve of the two-probe device shows typical transport behavior of Schottky barrier, and the threshold voltage is of about 0.2 V. The field effect transistors (FET) based on the planar junction turn out to be good bipolar transistors, the maximum current on/off ratio can reach up to 1 × 104, and the subthreshold swing is 243 mV/dec. It is found that the off-state current is dependent on the length and width of the channel, while the on-state current is almost unaffected. The switching performance of the FET is improved with increasing the length of the channel, and shows oscillation behavior with the change of the channel width.

Differential Regulation of Action Potential Shape and Burst-Frequency Firing by BK and Kv2 Channels in Substantia Nigra Dopaminergic Neurons

PubMed Central

Kimm, Tilia; Khaliq, Zayd M.

2015-01-01

Little is known about the voltage-dependent potassium currents underlying spike repolarization in midbrain dopaminergic neurons. Studying mouse substantia nigra pars compacta dopaminergic neurons both in brain slice and after acute dissociation, we found that BK calcium-activated potassium channels and Kv2 channels both make major contributions to the depolarization-activated potassium current. Inhibiting Kv2 or BK channels had very different effects on spike shape and evoked firing. Inhibiting Kv2 channels increased spike width and decreased the afterhyperpolarization, as expected for loss of an action potential-activated potassium conductance. BK inhibition also increased spike width but paradoxically increased the afterhyperpolarization. Kv2 channel inhibition steeply increased the slope of the frequency–current (f–I) relationship, whereas BK channel inhibition had little effect on the f–I slope or decreased it, sometimes resulting in slowed firing. Action potential clamp experiments showed that both BK and Kv2 current flow during spike repolarization but with very different kinetics, with Kv2 current activating later and deactivating more slowly. Further experiments revealed that inhibiting either BK or Kv2 alone leads to recruitment of additional current through the other channel type during the action potential as a consequence of changes in spike shape. Enhancement of slowly deactivating Kv2 current can account for the increased afterhyperpolarization produced by BK inhibition and likely underlies the very different effects on the f–I relationship. The cross-regulation of BK and Kv2 activation illustrates that the functional role of a channel cannot be defined in isolation but depends critically on the context of the other conductances in the cell. SIGNIFICANCE STATEMENT This work shows that BK calcium-activated potassium channels and Kv2 voltage-activated potassium channels both regulate action potentials in dopamine neurons of the substantia nigra pars compacta. Although both channel types participate in action potential repolarization about equally, they have contrasting and partially opposite effects in regulating neuronal firing at frequencies typical of bursting. Our analysis shows that this results from their different kinetic properties, with fast-activating BK channels serving to short-circuit activation of Kv2 channels, which tend to slow firing by producing a deep afterhyperpolarization. The cross-regulation of BK and Kv2 activation illustrates that the functional role of a channel cannot be defined in isolation but depends critically on the context of the other conductances in the cell. PMID:26674866

Differential Regulation of Action Potential Shape and Burst-Frequency Firing by BK and Kv2 Channels in Substantia Nigra Dopaminergic Neurons.

PubMed

Kimm, Tilia; Khaliq, Zayd M; Bean, Bruce P

2015-12-16

Little is known about the voltage-dependent potassium currents underlying spike repolarization in midbrain dopaminergic neurons. Studying mouse substantia nigra pars compacta dopaminergic neurons both in brain slice and after acute dissociation, we found that BK calcium-activated potassium channels and Kv2 channels both make major contributions to the depolarization-activated potassium current. Inhibiting Kv2 or BK channels had very different effects on spike shape and evoked firing. Inhibiting Kv2 channels increased spike width and decreased the afterhyperpolarization, as expected for loss of an action potential-activated potassium conductance. BK inhibition also increased spike width but paradoxically increased the afterhyperpolarization. Kv2 channel inhibition steeply increased the slope of the frequency-current (f-I) relationship, whereas BK channel inhibition had little effect on the f-I slope or decreased it, sometimes resulting in slowed firing. Action potential clamp experiments showed that both BK and Kv2 current flow during spike repolarization but with very different kinetics, with Kv2 current activating later and deactivating more slowly. Further experiments revealed that inhibiting either BK or Kv2 alone leads to recruitment of additional current through the other channel type during the action potential as a consequence of changes in spike shape. Enhancement of slowly deactivating Kv2 current can account for the increased afterhyperpolarization produced by BK inhibition and likely underlies the very different effects on the f-I relationship. The cross-regulation of BK and Kv2 activation illustrates that the functional role of a channel cannot be defined in isolation but depends critically on the context of the other conductances in the cell. This work shows that BK calcium-activated potassium channels and Kv2 voltage-activated potassium channels both regulate action potentials in dopamine neurons of the substantia nigra pars compacta. Although both channel types participate in action potential repolarization about equally, they have contrasting and partially opposite effects in regulating neuronal firing at frequencies typical of bursting. Our analysis shows that this results from their different kinetic properties, with fast-activating BK channels serving to short-circuit activation of Kv2 channels, which tend to slow firing by producing a deep afterhyperpolarization. The cross-regulation of BK and Kv2 activation illustrates that the functional role of a channel cannot be defined in isolation but depends critically on the context of the other conductances in the cell. Copyright © 2015 the authors 0270-6474/15/3516404-14$15.00/0.

Magnitude and frequency analysis on river width widening caused by Typhoon Morakot in the Kaoping River watershed, Taiwan

NASA Astrophysics Data System (ADS)

Yang, S. Y.; Jan, C. D.; Wang, Y. C.

2014-12-01

Active evolving rivers are some of the most dynamic and sensitive parts of landscapes. From geologic and geomorphic perspectives, a stable river channel can adjust its width, depth, and slope to prevent significant aggradation or degradation caused by external triggers, e.g., hydrologic events caused by typhoon storms. In particular, the processes of lateral riverbank erosion play a majorly important role in forming horizontal river geomorphology, dominating incised river widens and meanders. Sediment materials produced and mobilized from riverbanks can also be substantial sediment supplying into river channel networks, affecting watershed sediment yield. In Taiwan, the geological and climatic regimes usually combine to generate severely lateral erosion and/or riverbed deposition along river channels, causing the significant change in river width. In the August of 2009, Typhoon Morakot brought severe rainfall of about 2000 mmin Southern Taiwan during three days at the beginning of Aug. 5, leading to significant changes in geomorphic system. Here we characterized river width widening (including Cishan, Laonong, and Ilao Rivers) in the Kaoping River watershed after Typhoon Morakot disturbance interpreted through a power law. On the basis of a temporal pair (2008 and 2009) of Formosat-II (Formosa satellite II) images analysis, the river channels were digitalized within geographic information system (GIS), and river widths were extracted per 100 m along the rivers, then differentiating the adjustment of river width before and after Typhoon Morkot. The river width adjusted from -83 m (contracting) to 1985 m (widening), with an average of 170 m. The noncumulative frequency-magnitude distribution for river width adjustment caused by Typhoon Morakot in the study area satisfies a power-law relation with a determined coefficient (r2) of 0.95, over the range from 65 m to 2373m in the study area. Moreover, the value of the power-law exponent is equal to -2.09. This pattern suggests that river channel widening caused by large, infrequent hydrologic episodes has self-organized criticality. This study can provide useful information to river and watershed management, thereby refining the prevention and mitigation of hazard risks due to the effect of river width widening.

Search for a high-mass Higgs boson decaying to a W boson pair in pp collisions at √s = 8 TeV with the ATLAS detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aad, G.; Abbott, B.; Abdallah, J.

A search for a high-mass Higgs boson H is performed in the H → WW → ℓνℓν and H → WW → ℓνqq decay channels using pp collision data corresponding to an integrated luminosity of 20.3 fb -1 collected at √s = 8 TeV by the ATLAS detector at the Large Hadron Collider. No evidence of a high-mass Higgs boson is found. Limits on σ H × BR(H → WW) as a function of the Higgs boson mass m H are determined in three different scenarios: one in which the heavy Higgs boson has a narrow width compared to themore » experimental resolution, one for a width increasing with the boson mass and modeled by the complex-pole scheme following the same behavior as in the Standard Model, and one for intermediate widths. The upper range of the search is m H = 1500 GeV for the narrow-width scenario and m H = 1000 GeV for the other two scenarios. The lower edge of the search range is 200–300 GeV and depends on the analysis channel and search scenario. For each signal interpretation, individual and combined limits from the two WW decay channels are presented. Thus, at m H = 1500 GeV, the highest-mass point tested, σ H × BR(H → WW) for a narrow-width Higgs boson is constrained to be less than 22fb and 6.6fb at 95% CL for the gluon fusion and vector-boson fusion production modes, respectively.« less

Search for a high-mass Higgs boson decaying to a W boson pair in pp collisions at √{s}=8 TeV with the ATLAS detector

NASA Astrophysics Data System (ADS)

Aad, G.; Abbott, B.; Abdallah, J.; Abdinov, O.; Aben, R.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; Abreu, H.; Abreu, R.; Abulaiti, Y.; Acharya, B. S.; Adamczyk, L.; Adams, D. L.; Adelman, J.; Adomeit, S.; Adye, T.; Affolder, A. A.; Agatonovic-Jovin, T.; Agricola, J.; Aguilar-Saavedra, J. A.; Ahlen, S. P.; Ahmadov, F.; Aielli, G.; Akerstedt, H.; Åkesson, T. P. A.; Akimov, A. V.; Alberghi, G. L.; Albert, J.; Albrand, S.; Alconada Verzini, M. J.; Aleksa, M.; Aleksandrov, I. N.; Alexa, C.; Alexander, G.; Alexopoulos, T.; Alhroob, M.; Alimonti, G.; Alio, L.; Alison, J.; Alkire, S. P.; Allbrooke, B. M. M.; Allport, P. P.; Aloisio, A.; Alonso, A.; Alonso, F.; Alpigiani, C.; Altheimer, A.; Alvarez Gonzalez, B.; Álvarez Piqueras, D.; Alviggi, M. G.; Amadio, B. T.; Amako, K.; Amaral Coutinho, Y.; Amelung, C.; Amidei, D.; Amor Dos Santos, S. P.; Amorim, A.; Amoroso, S.; Amram, N.; Amundsen, G.; Anastopoulos, C.; Ancu, L. S.; Andari, N.; Andeen, T.; Anders, C. F.; Anders, G.; Anders, J. K.; Anderson, K. J.; Andreazza, A.; Andrei, V.; Angelidakis, S.; Angelozzi, I.; Anger, P.; Angerami, A.; Anghinolfi, F.; Anisenkov, A. V.; Anjos, N.; Annovi, A.; Antonelli, M.; Antonov, A.; Antos, J.; Anulli, F.; Aoki, M.; Aperio Bella, L.; Arabidze, G.; Arai, Y.; Araque, J. P.; Arce, A. T. H.; Arduh, F. A.; Arguin, J.-F.; Argyropoulos, S.; Arik, M.; Armbruster, A. J.; Arnaez, O.; Arnal, V.; Arnold, H.; Arratia, M.; Arslan, O.; Artamonov, A.; Artoni, G.; Asai, S.; Asbah, N.; Ashkenazi, A.; Åsman, B.; Asquith, L.; Assamagan, K.; Astalos, R.; Atkinson, M.; Atlay, N. B.; Augsten, K.; Aurousseau, M.; Avolio, G.; Axen, B.; Ayoub, M. K.; Azuelos, G.; Baak, M. A.; Baas, A. E.; Baca, M. J.; Bacci, C.; Bachacou, H.; Bachas, K.; Backes, M.; Backhaus, M.; Bagiacchi, P.; Bagnaia, P.; Bai, Y.; Bain, T.; Baines, J. T.; Baker, O. K.; Baldin, E. M.; Balek, P.; Balestri, T.; Balli, F.; Balunas, W. K.; Banas, E.; Banerjee, Sw.; Bannoura, A. A. E.; Bansil, H. S.; Barak, L.; Barberio, E. L.; Barberis, D.; Barbero, M.; Barillari, T.; Barisonzi, M.; Barklow, T.; Barlow, N.; Barnes, S. L.; Barnett, B. M.; Barnett, R. M.; Barnovska, Z.; Baroncelli, A.; Barone, G.; Barr, A. J.; Barreiro, F.; Barreiro Guimarães da Costa, J.; Bartoldus, R.; Barton, A. E.; Bartos, P.; Basalaev, A.; Bassalat, A.; Basye, A.; Bates, R. L.; Batista, S. J.; Batley, J. R.; Battaglia, M.; Bauce, M.; Bauer, F.; Bawa, H. S.; Beacham, J. B.; Beattie, M. D.; Beau, T.; Beauchemin, P. H.; Beccherle, R.; Bechtle, P.; Beck, H. P.; Becker, K.; Becker, M.; Beckingham, M.; Becot, C.; Beddall, A. J.; Beddall, A.; Bednyakov, V. A.; Bee, C. P.; Beemster, L. J.; Beermann, T. A.; Begel, M.; Behr, J. K.; Belanger-Champagne, C.; Bell, W. H.; Bella, G.; Bellagamba, L.; Bellerive, A.; Bellomo, M.; Belotskiy, K.; Beltramello, O.; Benary, O.; Benchekroun, D.; Bender, M.; Bendtz, K.; Benekos, N.; Benhammou, Y.; Benhar Noccioli, E.; Benitez Garcia, J. A.; Benjamin, D. P.; Bensinger, J. R.; Bentvelsen, S.; Beresford, L.; Beretta, M.; Berge, D.; Bergeaas Kuutmann, E.; Berger, N.; Berghaus, F.; Beringer, J.; Bernard, C.; Bernard, N. R.; Bernius, C.; Bernlochner, F. U.; Berry, T.; Berta, P.; Bertella, C.; Bertoli, G.; Bertolucci, F.; Bertsche, C.; Bertsche, D.; Besana, M. I.; Besjes, G. J.; Bessidskaia Bylund, O.; Bessner, M.; Besson, N.; Betancourt, C.; Bethke, S.; Bevan, A. J.; Bhimji, W.; Bianchi, R. M.; Bianchini, L.; Bianco, M.; Biebel, O.; Biedermann, D.; Bieniek, S. P.; Biglietti, M.; Bilbao De Mendizabal, J.; Bilokon, H.; Bindi, M.; Binet, S.; Bingul, A.; Bini, C.; Biondi, S.; Bjergaard, D. M.; Black, C. W.; Black, J. E.; Black, K. M.; Blackburn, D.; Blair, R. E.; Blanchard, J.-B.; Blanco, J. E.; Blazek, T.; Bloch, I.; Blocker, C.; Blum, W.; Blumenschein, U.; Bobbink, G. J.; Bobrovnikov, V. S.; Bocchetta, S. S.; Bocci, A.; Bock, C.; Boehler, M.; Bogaerts, J. A.; Bogavac, D.; Bogdanchikov, A. G.; Bohm, C.; Boisvert, V.; Bold, T.; Boldea, V.; Boldyrev, A. S.; Bomben, M.; Bona, M.; Boonekamp, M.; Borisov, A.; Borissov, G.; Borroni, S.; Bortfeldt, J.; Bortolotto, V.; Bos, K.; Boscherini, D.; Bosman, M.; Boudreau, J.; Bouffard, J.; Bouhova-Thacker, E. V.; Boumediene, D.; Bourdarios, C.; Bousson, N.; Boutle, S. K.; Boveia, A.; Boyd, J.; Boyko, I. R.; Bozic, I.; Bracinik, J.; Brandt, A.; Brandt, G.; Brandt, O.; Bratzler, U.; Brau, B.; Brau, J. E.; Braun, H. M.; Brazzale, S. F.; Breaden Madden, W. D.; Brendlinger, K.; Brennan, A. J.; Brenner, L.; Brenner, R.; Bressler, S.; Bristow, K.; Bristow, T. M.; Britton, D.; Britzger, D.; Brochu, F. M.; Brock, I.; Brock, R.; Bronner, J.; Brooijmans, G.; Brooks, T.; Brooks, W. K.; Brosamer, J.; Brost, E.; Brown, J.; Bruckman de Renstrom, P. A.; Bruncko, D.; Bruneliere, R.; Bruni, A.; Bruni, G.; Bruschi, M.; Bruscino, N.; Bryngemark, L.; Buanes, T.; Buat, Q.; Buchholz, P.; Buckley, A. G.; Buda, S. I.; Budagov, I. A.; Buehrer, F.; Bugge, L.; Bugge, M. K.; Bulekov, O.; Bullock, D.; Burckhart, H.; Burdin, S.; Burgard, C. D.; Burghgrave, B.; Burke, S.; Burmeister, I.; Busato, E.; Büscher, D.; Büscher, V.; Bussey, P.; Butler, J. M.; Butt, A. I.; Buttar, C. M.; Butterworth, J. M.; Butti, P.; Buttinger, W.; Buzatu, A.; Buzykaev, A. R.; Cabrera Urbán, S.; Caforio, D.; Cairo, V. M.; Cakir, O.; Calace, N.; Calafiura, P.; Calandri, A.; Calderini, G.; Calfayan, P.; Caloba, L. P.; Calvet, D.; Calvet, S.; Camacho Toro, R.; Camarda, S.; Camarri, P.; Cameron, D.; Caminal Armadans, R.; Campana, S.; Campanelli, M.; Campoverde, A.; Canale, V.; Canepa, A.; Cano Bret, M.; Cantero, J.; Cantrill, R.; Cao, T.; Capeans Garrido, M. D. M.; Caprini, I.; Caprini, M.; Capua, M.; Caputo, R.; Cardarelli, R.; Cardillo, F.; Carli, T.; Carlino, G.; Carminati, L.; Caron, S.; Carquin, E.; Carrillo-Montoya, G. D.; Carter, J. R.; Carvalho, J.; Casadei, D.; Casado, M. P.; Casolino, M.; Castaneda-Miranda, E.; Castelli, A.; Castillo Gimenez, V.; Castro, N. F.; Catastini, P.; Catinaccio, A.; Catmore, J. R.; Cattai, A.; Caudron, J.; Cavaliere, V.; Cavalli, D.; Cavalli-Sforza, M.; Cavasinni, V.; Ceradini, F.; Cerio, B. C.; Cerny, K.; Cerqueira, A. S.; Cerri, A.; Cerrito, L.; Cerutti, F.; Cerv, M.; Cervelli, A.; Cetin, S. A.; Chafaq, A.; Chakraborty, D.; Chalupkova, I.; Chang, P.; Chapman, J. D.; Charlton, D. G.; Chau, C. C.; Chavez Barajas, C. A.; Cheatham, S.; Chegwidden, A.; Chekanov, S.; Chekulaev, S. V.; Chelkov, G. A.; Chelstowska, M. A.; Chen, C.; Chen, H.; Chen, K.; Chen, L.; Chen, S.; Chen, S.; Chen, X.; Chen, Y.; Cheng, H. C.; Cheng, Y.; Cheplakov, A.; Cheremushkina, E.; Cherkaoui El Moursli, R.; Chernyatin, V.; Cheu, E.; Chevalier, L.; Chiarella, V.; Chiarelli, G.; Chiodini, G.; Chisholm, A. S.; Chislett, R. T.; Chitan, A.; Chizhov, M. V.; Choi, K.; Chouridou, S.; Chow, B. K. B.; Christodoulou, V.; Chromek-Burckhart, D.; Chudoba, J.; Chuinard, A. J.; Chwastowski, J. J.; Chytka, L.; Ciapetti, G.; Ciftci, A. K.; Cinca, D.; Cindro, V.; Cioara, I. A.; Ciocio, A.; Cirotto, F.; Citron, Z. H.; Ciubancan, M.; Clark, A.; Clark, B. L.; Clark, P. J.; Clarke, R. N.; Cleland, W.; Clement, C.; Coadou, Y.; Cobal, M.; Coccaro, A.; Cochran, J.; Coffey, L.; Cogan, J. G.; Colasurdo, L.; Cole, B.; Cole, S.; Colijn, A. P.; Collot, J.; Colombo, T.; Compostella, G.; Conde Muiño, P.; Coniavitis, E.; Connell, S. H.; Connelly, I. A.; Consorti, V.; Constantinescu, S.; Conta, C.; Conti, G.; Conventi, F.; Cooke, M.; Cooper, B. D.; Cooper-Sarkar, A. M.; Cornelissen, T.; Corradi, M.; Corriveau, F.; Corso-Radu, A.; Cortes-Gonzalez, A.; Cortiana, G.; Costa, G.; Costa, M. J.; Costanzo, D.; Côté, D.; Cottin, G.; Cowan, G.; Cox, B. E.; Cranmer, K.; Cree, G.; Crépé-Renaudin, S.; Crescioli, F.; Cribbs, W. A.; Crispin Ortuzar, M.; Cristinziani, M.; Croft, V.; Crosetti, G.; Cuhadar Donszelmann, T.; Cummings, J.; Curatolo, M.; Cúth, J.; Cuthbert, C.; Czirr, H.; Czodrowski, P.; D'Auria, S.; D'Onofrio, M.; Da Cunha Sargedas De Sousa, M. J.; Da Via, C.; Dabrowski, W.; Dafinca, A.; Dai, T.; Dale, O.; Dallaire, F.; Dallapiccola, C.; Dam, M.; Dandoy, J. R.; Dang, N. P.; Daniells, A. C.; Danninger, M.; Dano Hoffmann, M.; Dao, V.; Darbo, G.; Darmora, S.; Dassoulas, J.; Dattagupta, A.; Davey, W.; David, C.; Davidek, T.; Davies, E.; Davies, M.; Davison, P.; Davygora, Y.; Dawe, E.; Dawson, I.; Daya-Ishmukhametova, R. K.; De, K.; de Asmundis, R.; De Benedetti, A.; De Castro, S.; De Cecco, S.; De Groot, N.; de Jong, P.; De la Torre, H.; De Lorenzi, F.; De Pedis, D.; De Salvo, A.; De Sanctis, U.; De Santo, A.; De Vivie De Regie, J. B.; Dearnaley, W. J.; Debbe, R.; Debenedetti, C.; Dedovich, D. V.; Deigaard, I.; Del Peso, J.; Del Prete, T.; Delgove, D.; Deliot, F.; Delitzsch, C. M.; Deliyergiyev, M.; Dell'Acqua, A.; Dell'Asta, L.; Dell'Orso, M.; Della Pietra, M.; della Volpe, D.; Delmastro, M.; Delsart, P. A.; Deluca, C.; DeMarco, D. A.; Demers, S.; Demichev, M.; Demilly, A.; Denisov, S. P.; Derendarz, D.; Derkaoui, J. E.; Derue, F.; Dervan, P.; Desch, K.; Deterre, C.; Deviveiros, P. O.; Dewhurst, A.; Dhaliwal, S.; Di Ciaccio, A.; Di Ciaccio, L.; Di Domenico, A.; Di Donato, C.; Di Girolamo, A.; Di Girolamo, B.; Di Mattia, A.; Di Micco, B.; Di Nardo, R.; Di Simone, A.; Di Sipio, R.; Di Valentino, D.; Diaconu, C.; Diamond, M.; Dias, F. A.; Diaz, M. A.; Diehl, E. B.; Dietrich, J.; Diglio, S.; Dimitrievska, A.; Dingfelder, J.; Dita, P.; Dita, S.; Dittus, F.; Djama, F.; Djobava, T.; Djuvsland, J. I.; do Vale, M. A. B.; Dobos, D.; Dobre, M.; Doglioni, C.; Dohmae, T.; Dolejsi, J.; Dolezal, Z.; Dolgoshein, B. A.; Donadelli, M.; Donati, S.; Dondero, P.; Donini, J.; Dopke, J.; Doria, A.; Dova, M. T.; Doyle, A. T.; Drechsler, E.; Dris, M.; Dubreuil, E.; Duchovni, E.; Duckeck, G.; Ducu, O. A.; Duda, D.; Dudarev, A.; Duflot, L.; Duguid, L.; Dührssen, M.; Dunford, M.; Duran Yildiz, H.; Düren, M.; Durglishvili, A.; Duschinger, D.; Dyndal, M.; Eckardt, C.; Ecker, K. M.; Edgar, R. C.; Edson, W.; Edwards, N. C.; Ehrenfeld, W.; Eifert, T.; Eigen, G.; Einsweiler, K.; Ekelof, T.; El Kacimi, M.; Ellert, M.; Elles, S.; Ellinghaus, F.; Elliot, A. A.; Ellis, N.; Elmsheuser, J.; Elsing, M.; Emeliyanov, D.; Enari, Y.; Endner, O. C.; Endo, M.; Erdmann, J.; Ereditato, A.; Ernis, G.; Ernst, J.; Ernst, M.; Errede, S.; Ertel, E.; Escalier, M.; Esch, H.; Escobar, C.; Esposito, B.; Etienvre, A. I.; Etzion, E.; Evans, H.; Ezhilov, A.; Fabbri, L.; Facini, G.; Fakhrutdinov, R. M.; Falciano, S.; Falla, R. J.; Faltova, J.; Fang, Y.; Fanti, M.; Farbin, A.; Farilla, A.; Farooque, T.; Farrell, S.; Farrington, S. M.; Farthouat, P.; Fassi, F.; Fassnacht, P.; Fassouliotis, D.; Faucci Giannelli, M.; Favareto, A.; Fayard, L.; Federic, P.; Fedin, O. L.; Fedorko, W.; Feigl, S.; Feligioni, L.; Feng, C.; Feng, E. J.; Feng, H.; Fenyuk, A. B.; Feremenga, L.; Fernandez Martinez, P.; Fernandez Perez, S.; Ferrando, J.; Ferrari, A.; Ferrari, P.; Ferrari, R.; Ferreira de Lima, D. E.; Ferrer, A.; Ferrere, D.; Ferretti, C.; Ferretto Parodi, A.; Fiascaris, M.; Fiedler, F.; Filipčič, A.; Filipuzzi, M.; Filthaut, F.; Fincke-Keeler, M.; Finelli, K. D.; Fiolhais, M. C. N.; Fiorini, L.; Firan, A.; Fischer, A.; Fischer, C.; Fischer, J.; Fisher, W. C.; Fitzgerald, E. A.; Flaschel, N.; Fleck, I.; Fleischmann, P.; Fleischmann, S.; Fletcher, G. T.; Fletcher, G.; Fletcher, R. R. M.; Flick, T.; Floderus, A.; Flores Castillo, L. R.; Flowerdew, M. J.; Formica, A.; Forti, A.; Fournier, D.; Fox, H.; Fracchia, S.; Francavilla, P.; Franchini, M.; Francis, D.; Franconi, L.; Franklin, M.; Frate, M.; Fraternali, M.; Freeborn, D.; French, S. T.; Friedrich, F.; Froidevaux, D.; Frost, J. A.; Fukunaga, C.; Fullana Torregrosa, E.; Fulsom, B. G.; Fusayasu, T.; Fuster, J.; Gabaldon, C.; Gabizon, O.; Gabrielli, A.; Gabrielli, A.; Gach, G. P.; Gadatsch, S.; Gadomski, S.; Gagliardi, G.; Gagnon, P.; Galea, C.; Galhardo, B.; Gallas, E. J.; Gallop, B. J.; Gallus, P.; Galster, G.; Gan, K. K.; Gao, J.; Gao, Y.; Gao, Y. S.; Garay Walls, F. M.; Garberson, F.; García, C.; García Navarro, J. E.; Garcia-Sciveres, M.; Gardner, R. W.; Garelli, N.; Garonne, V.; Gatti, C.; Gaudiello, A.; Gaudio, G.; Gaur, B.; Gauthier, L.; Gauzzi, P.; Gavrilenko, I. L.; Gay, C.; Gaycken, G.; Gazis, E. N.; Ge, P.; Gecse, Z.; Gee, C. N. P.; Geich-Gimbel, Ch.; Geisler, M. P.; Gemme, C.; Genest, M. H.; Gentile, S.; George, M.; George, S.; Gerbaudo, D.; Gershon, A.; Ghasemi, S.; Ghazlane, H.; Giacobbe, B.; Giagu, S.; Giangiobbe, V.; Giannetti, P.; Gibbard, B.; Gibson, S. M.; Gilchriese, M.; Gillam, T. P. S.; Gillberg, D.; Gilles, G.; Gingrich, D. M.; Giokaris, N.; Giordani, M. P.; Giorgi, F. M.; Giorgi, F. M.; Giraud, P. F.; Giromini, P.; Giugni, D.; Giuliani, C.; Giulini, M.; Gjelsten, B. K.; Gkaitatzis, S.; Gkialas, I.; Gkougkousis, E. L.; Gladilin, L. K.; Glasman, C.; Glatzer, J.; Glaysher, P. C. F.; Glazov, A.; Goblirsch-Kolb, M.; Goddard, J. R.; Godlewski, J.; Goldfarb, S.; Golling, T.; Golubkov, D.; Gomes, A.; Gonçalo, R.; Goncalves Pinto Firmino Da Costa, J.; Gonella, L.; González de la Hoz, S.; Gonzalez Parra, G.; Gonzalez-Sevilla, S.; Goossens, L.; Gorbounov, P. A.; Gordon, H. A.; Gorelov, I.; Gorini, B.; Gorini, E.; Gorišek, A.; Gornicki, E.; Goshaw, A. T.; Gössling, C.; Gostkin, M. I.; Goujdami, D.; Goussiou, A. G.; Govender, N.; Gozani, E.; Grabas, H. M. X.; Graber, L.; Grabowska-Bold, I.; Gradin, P. O. J.; Grafström, P.; Grahn, K.-J.; Gramling, J.; Gramstad, E.; Grancagnolo, S.; Gratchev, V.; Gray, H. M.; Graziani, E.; Greenwood, Z. D.; Grefe, C.; Gregersen, K.; Gregor, I. M.; Grenier, P.; Griffiths, J.; Grillo, A. A.; Grimm, K.; Grinstein, S.; Gris, Ph.; Grivaz, J.-F.; Grohs, J. P.; Grohsjean, A.; Gross, E.; Grosse-Knetter, J.; Grossi, G. C.; Grout, Z. J.; Guan, L.; Guenther, J.; Guescini, F.; Guest, D.; Gueta, O.; Guido, E.; Guillemin, T.; Guindon, S.; Gul, U.; Gumpert, C.; Guo, J.; Guo, Y.; Gupta, S.; Gustavino, G.; Gutierrez, P.; Gutierrez Ortiz, N. G.; Gutschow, C.; Guyot, C.; Gwenlan, C.; Gwilliam, C. B.; Haas, A.; Haber, C.; Hadavand, H. K.; Haddad, N.; Haefner, P.; Hageböck, S.; Hajduk, Z.; Hakobyan, H.; Haleem, M.; Haley, J.; Hall, D.; Halladjian, G.; Hallewell, G. D.; Hamacher, K.; Hamal, P.; Hamano, K.; Hamilton, A.; Hamity, G. N.; Hamnett, P. G.; Han, L.; Hanagaki, K.; Hanawa, K.; Hance, M.; Haney, B.; Hanke, P.; Hanna, R.; Hansen, J. B.; Hansen, J. D.; Hansen, M. C.; Hansen, P. H.; Hara, K.; Hard, A. S.; Harenberg, T.; Hariri, F.; Harkusha, S.; Harrington, R. D.; Harrison, P. F.; Hartjes, F.; Hasegawa, M.; Hasegawa, Y.; Hasib, A.; Hassani, S.; Haug, S.; Hauser, R.; Hauswald, L.; Havranek, M.; Hawkes, C. M.; Hawkings, R. J.; Hawkins, A. D.; Hayashi, T.; Hayden, D.; Hays, C. P.; Hays, J. M.; Hayward, H. S.; Haywood, S. J.; Head, S. J.; Heck, T.; Hedberg, V.; Heelan, L.; Heim, S.; Heim, T.; Heinemann, B.; Heinrich, L.; Hejbal, J.; Helary, L.; Hellman, S.; Hellmich, D.; Helsens, C.; Henderson, J.; Henderson, R. C. W.; Heng, Y.; Hengler, C.; Henkelmann, S.; Henrichs, A.; Henriques Correia, A. M.; Henrot-Versille, S.; Herbert, G. H.; Hernández Jiménez, Y.; Herrberg-Schubert, R.; Herten, G.; Hertenberger, R.; Hervas, L.; Hesketh, G. G.; Hessey, N. P.; Hetherly, J. W.; Hickling, R.; Higón-Rodriguez, E.; Hill, E.; Hill, J. C.; Hiller, K. H.; Hillier, S. J.; Hinchliffe, I.; Hines, E.; Hinman, R. R.; Hirose, M.; Hirschbuehl, D.; Hobbs, J.; Hod, N.; Hodgkinson, M. C.; Hodgson, P.; Hoecker, A.; Hoeferkamp, M. R.; Hoenig, F.; Hohlfeld, M.; Hohn, D.; Holmes, T. R.; Homann, M.; Hong, T. M.; Hooft van Huysduynen, L.; Hopkins, W. H.; Horii, Y.; Horton, A. J.; Hostachy, J.-Y.; Hou, S.; Hoummada, A.; Howard, J.; Howarth, J.; Hrabovsky, M.; Hristova, I.; Hrivnac, J.; Hryn'ova, T.; Hrynevich, A.; Hsu, C.; Hsu, P. J.; Hsu, S.-C.; Hu, D.; Hu, Q.; Hu, X.; Huang, Y.; Hubacek, Z.; Hubaut, F.; Huegging, F.; Huffman, T. B.; Hughes, E. W.; Hughes, G.; Huhtinen, M.; Hülsing, T. A.; Huseynov, N.; Huston, J.; Huth, J.; Iacobucci, G.; Iakovidis, G.; Ibragimov, I.; Iconomidou-Fayard, L.; Ideal, E.; Idrissi, Z.; Iengo, P.; Igonkina, O.; Iizawa, T.; Ikegami, Y.; Ikematsu, K.; Ikeno, M.; Ilchenko, Y.; Iliadis, D.; Ilic, N.; Ince, T.; Introzzi, G.; Ioannou, P.; Iodice, M.; Iordanidou, K.; Ippolito, V.; Irles Quiles, A.; Isaksson, C.; Ishino, M.; Ishitsuka, M.; Ishmukhametov, R.; Issever, C.; Istin, S.; Iturbe Ponce, J. M.; Iuppa, R.; Ivarsson, J.; Iwanski, W.; Iwasaki, H.; Izen, J. M.; Izzo, V.; Jabbar, S.; Jackson, B.; Jackson, M.; Jackson, P.; Jaekel, M. R.; Jain, V.; Jakobs, K.; Jakobsen, S.; Jakoubek, T.; Jakubek, J.; Jamin, D. O.; Jana, D. K.; Jansen, E.; Jansky, R.; Janssen, J.; Janus, M.; Jarlskog, G.; Javadov, N.; Javůrek, T.; Jeanty, L.; Jejelava, J.; Jeng, G.-Y.; Jennens, D.; Jenni, P.; Jentzsch, J.; Jeske, C.; Jézéquel, S.; Ji, H.; Jia, J.; Jiang, Y.; Jiggins, S.; Jimenez Pena, J.; Jin, S.; Jinaru, A.; Jinnouchi, O.; Joergensen, M. D.; Johansson, P.; Johns, K. A.; Jon-And, K.; Jones, G.; Jones, R. W. L.; Jones, T. J.; Jongmanns, J.; Jorge, P. M.; Joshi, K. D.; Jovicevic, J.; Ju, X.; Jung, C. A.; Jussel, P.; Juste Rozas, A.; Kaci, M.; Kaczmarska, A.; Kado, M.; Kagan, H.; Kagan, M.; Kahn, S. J.; Kajomovitz, E.; Kalderon, C. W.; Kama, S.; Kamenshchikov, A.; Kanaya, N.; Kaneti, S.; Kantserov, V. A.; Kanzaki, J.; Kaplan, B.; Kaplan, L. S.; Kapliy, A.; Kar, D.; Karakostas, K.; Karamaoun, A.; Karastathis, N.; Kareem, M. J.; Karentzos, E.; Karnevskiy, M.; Karpov, S. N.; Karpova, Z. M.; Karthik, K.; Kartvelishvili, V.; Karyukhin, A. N.; Kashif, L.; Kass, R. D.; Kastanas, A.; Kataoka, Y.; Kato, C.; Katre, A.; Katzy, J.; Kawagoe, K.; Kawamoto, T.; Kawamura, G.; Kazama, S.; Kazanin, V. F.; Keeler, R.; Kehoe, R.; Keller, J. S.; Kempster, J. J.; Keoshkerian, H.; Kepka, O.; Kerševan, B. P.; Kersten, S.; Keyes, R. A.; Khalil-zada, F.; Khandanyan, H.; Khanov, A.; Kharlamov, A. G.; Khoo, T. J.; Khovanskiy, V.; Khramov, E.; Khubua, J.; Kido, S.; Kim, H. Y.; Kim, S. H.; Kim, Y. K.; Kimura, N.; Kind, O. M.; King, B. T.; King, M.; King, S. B.; Kirk, J.; Kiryunin, A. E.; Kishimoto, T.; Kisielewska, D.; Kiss, F.; Kiuchi, K.; Kivernyk, O.; Kladiva, E.; Klein, M. H.; Klein, M.; Klein, U.; Kleinknecht, K.; Klimek, P.; Klimentov, A.; Klingenberg, R.; Klinger, J. A.; Klioutchnikova, T.; Kluge, E.-E.; Kluit, P.; Kluth, S.; Knapik, J.; Kneringer, E.; Knoops, E. B. F. G.; Knue, A.; Kobayashi, A.; Kobayashi, D.; Kobayashi, T.; Kobel, M.; Kocian, M.; Kodys, P.; Koffas, T.; Koffeman, E.; Kogan, L. A.; Kohlmann, S.; Kohout, Z.; Kohriki, T.; Koi, T.; Kolanoski, H.; Koletsou, I.; Komar, A. A.; Komori, Y.; Kondo, T.; Kondrashova, N.; Köneke, K.; König, A. C.; Kono, T.; Konoplich, R.; Konstantinidis, N.; Kopeliansky, R.; Koperny, S.; Köpke, L.; Kopp, A. K.; Korcyl, K.; Kordas, K.; Korn, A.; Korol, A. A.; Korolkov, I.; Korolkova, E. V.; Kortner, O.; Kortner, S.; Kosek, T.; Kostyukhin, V. V.; Kotov, V. M.; Kotwal, A.; Kourkoumeli-Charalampidi, A.; Kourkoumelis, C.; Kouskoura, V.; Koutsman, A.; Kowalewski, R.; Kowalski, T. Z.; Kozanecki, W.; Kozhin, A. S.; Kramarenko, V. A.; Kramberger, G.; Krasnopevtsev, D.; Krasny, M. W.; Krasznahorkay, A.; Kraus, J. K.; Kravchenko, A.; Kreiss, S.; Kretz, M.; Kretzschmar, J.; Kreutzfeldt, K.; Krieger, P.; Krizka, K.; Kroeninger, K.; Kroha, H.; Kroll, J.; Kroseberg, J.; Krstic, J.; Kruchonak, U.; Krüger, H.; Krumnack, N.; Kruse, A.; Kruse, M. C.; Kruskal, M.; Kubota, T.; Kucuk, H.; Kuday, S.; Kuehn, S.; Kugel, A.; Kuger, F.; Kuhl, A.; Kuhl, T.; Kukhtin, V.; Kukla, R.; Kulchitsky, Y.; Kuleshov, S.; Kuna, M.; Kunigo, T.; Kupco, A.; Kurashige, H.; Kurochkin, Y. A.; Kus, V.; Kuwertz, E. S.; Kuze, M.; Kvita, J.; Kwan, T.; Kyriazopoulos, D.; La Rosa, A.; La Rosa Navarro, J. L.; La Rotonda, L.; Lacasta, C.; Lacava, F.; Lacey, J.; Lacker, H.; Lacour, D.; Lacuesta, V. R.; Ladygin, E.; Lafaye, R.; Laforge, B.; Lagouri, T.; Lai, S.; Lambourne, L.; Lammers, S.; Lampen, C. L.; Lampl, W.; Lançon, E.; Landgraf, U.; Landon, M. P. J.; Lang, V. S.; Lange, J. C.; Lankford, A. J.; Lanni, F.; Lantzsch, K.; Lanza, A.; Laplace, S.; Lapoire, C.; Laporte, J. F.; Lari, T.; Lasagni Manghi, F.; Lassnig, M.; Laurelli, P.; Lavrijsen, W.; Law, A. T.; Laycock, P.; Lazovich, T.; Le Dortz, O.; Le Guirriec, E.; Le Menedeu, E.; LeBlanc, M.; LeCompte, T.; Ledroit-Guillon, F.; Lee, C. A.; Lee, S. C.; Lee, L.; Lefebvre, G.; Lefebvre, M.; Legger, F.; Leggett, C.; Lehan, A.; Lehmann Miotto, G.; Lei, X.; Leight, W. A.; Leisos, A.; Leister, A. G.; Leite, M. A. L.; Leitner, R.; Lellouch, D.; Lemmer, B.; Leney, K. J. C.; Lenz, T.; Lenzi, B.; Leone, R.; Leone, S.; Leonidopoulos, C.; Leontsinis, S.; Leroy, C.; Lester, C. G.; Levchenko, M.; Levêque, J.; Levin, D.; Levinson, L. J.; Levy, M.; Lewis, A.; Leyko, A. M.; Leyton, M.; Li, B.; Li, H.; Li, H. L.; Li, L.; Li, L.; Li, S.; Li, X.; Li, Y.; Liang, Z.; Liao, H.; Liberti, B.; Liblong, A.; Lichard, P.; Lie, K.; Liebal, J.; Liebig, W.; Limbach, C.; Limosani, A.; Lin, S. C.; Lin, T. H.; Linde, F.; Lindquist, B. E.; Linnemann, J. T.; Lipeles, E.; Lipniacka, A.; Lisovyi, M.; Liss, T. M.; Lissauer, D.; Lister, A.; Litke, A. M.; Liu, B.; Liu, D.; Liu, H.; Liu, J.; Liu, J. B.; Liu, K.; Liu, L.; Liu, M.; Liu, M.; Liu, Y.; Livan, M.; Lleres, A.; Llorente Merino, J.; Lloyd, S. L.; Lo Sterzo, F.; Lobodzinska, E.; Loch, P.; Lockman, W. S.; Loebinger, F. K.; Loevschall-Jensen, A. E.; Loew, K. M.; Loginov, A.; Lohse, T.; Lohwasser, K.; Lokajicek, M.; Long, B. A.; Long, J. D.; Long, R. E.; Looper, K. A.; Lopes, L.; Lopez Mateos, D.; Lopez Paredes, B.; Lopez Paz, I.; Lorenz, J.; Lorenzo Martinez, N.; Losada, M.; Lösel, P. J.; Lou, X.; Lounis, A.; Love, J.; Love, P. A.; Lu, N.; Lubatti, H. J.; Luci, C.; Lucotte, A.; Luehring, F.; Lukas, W.; Luminari, L.; Lundberg, O.; Lund-Jensen, B.; Lynn, D.; Lysak, R.; Lytken, E.; Ma, H.; Ma, L. L.; Maccarrone, G.; Macchiolo, A.; Macdonald, C. M.; Maček, B.; Machado Miguens, J.; Macina, D.; Madaffari, D.; Madar, R.; Maddocks, H. J.; Mader, W. F.; Madsen, A.; Maeda, J.; Maeland, S.; Maeno, T.; Maevskiy, A.; Magradze, E.; Mahboubi, K.; Mahlstedt, J.; Maiani, C.; Maidantchik, C.; Maier, A. A.; Maier, T.; Maio, A.; Majewski, S.; Makida, Y.; Makovec, N.; Malaescu, B.; Malecki, Pa.; Maleev, V. P.; Malek, F.; Mallik, U.; Malon, D.; Malone, C.; Maltezos, S.; Malyshev, V. M.; Malyukov, S.; Mamuzic, J.; Mancini, G.; Mandelli, B.; Mandelli, L.; Mandić, I.; Mandrysch, R.; Maneira, J.; Manfredini, A.; Manhaes de Andrade Filho, L.; Manjarres Ramos, J.; Mann, A.; Manousakis-Katsikakis, A.; Mansoulie, B.; Mantifel, R.; Mantoani, M.; Mapelli, L.; March, L.; Marchiori, G.; Marcisovsky, M.; Marino, C. P.; Marjanovic, M.; Marley, D. E.; Marroquim, F.; Marsden, S. P.; Marshall, Z.; Marti, L. F.; Marti-Garcia, S.; Martin, B.; Martin, T. A.; Martin, V. J.; Martin dit Latour, B.; Martinez, M.; Martin-Haugh, S.; Martoiu, V. S.; Martyniuk, A. C.; Marx, M.; Marzano, F.; Marzin, A.; Masetti, L.; Mashimo, T.; Mashinistov, R.; Masik, J.; Maslennikov, A. L.; Massa, I.; Massa, L.; Mastrandrea, P.; Mastroberardino, A.; Masubuchi, T.; Mättig, P.; Mattmann, J.; Maurer, J.; Maxfield, S. J.; Maximov, D. A.; Mazini, R.; Mazza, S. M.; Mazzaferro, L.; Mc Goldrick, G.; Mc Kee, S. P.; McCarn, A.; McCarthy, R. L.; McCarthy, T. G.; McCubbin, N. A.; McFarlane, K. W.; Mcfayden, J. A.; Mchedlidze, G.; McMahon, S. J.; McPherson, R. A.; Medinnis, M.; Meehan, S.; Mehlhase, S.; Mehta, A.; Meier, K.; Meineck, C.; Meirose, B.; Mellado Garcia, B. R.; Meloni, F.; Mengarelli, A.; Menke, S.; Meoni, E.; Mercurio, K. M.; Mergelmeyer, S.; Mermod, P.; Merola, L.; Meroni, C.; Merritt, F. S.; Messina, A.; Metcalfe, J.; Mete, A. S.; Meyer, C.; Meyer, C.; Meyer, J.-P.; Meyer, J.; Meyer Zu Theenhausen, H.; Middleton, R. P.; Miglioranzi, S.; Mijović, L.; Mikenberg, G.; Mikestikova, M.; Mikuž, M.; Milesi, M.; Milic, A.; Miller, D. W.; Mills, C.; Milov, A.; Milstead, D. A.; Minaenko, A. A.; Minami, Y.; Minashvili, I. A.; Mincer, A. I.; Mindur, B.; Mineev, M.; Ming, Y.; Mir, L. M.; Mistry, K. P.; Mitani, T.; Mitrevski, J.; Mitsou, V. A.; Miucci, A.; Miyagawa, P. S.; Mjörnmark, J. U.; Moa, T.; Mochizuki, K.; Mohapatra, S.; Mohr, W.; Molander, S.; Moles-Valls, R.; Monden, R.; Mönig, K.; Monini, C.; Monk, J.; Monnier, E.; Montejo Berlingen, J.; Monticelli, F.; Monzani, S.; Moore, R. W.; Morange, N.; Moreno, D.; Moreno Llácer, M.; Morettini, P.; Mori, D.; Mori, T.; Morii, M.; Morinaga, M.; Morisbak, V.; Moritz, S.; Morley, A. K.; Mornacchi, G.; Morris, J. D.; Mortensen, S. S.; Morton, A.; Morvaj, L.; Mosidze, M.; Moss, J.; Motohashi, K.; Mount, R.; Mountricha, E.; Mouraviev, S. V.; Moyse, E. J. W.; Muanza, S.; Mudd, R. D.; Mueller, F.; Mueller, J.; Mueller, R. S. P.; Mueller, T.; Muenstermann, D.; Mullen, P.; Mullier, G. A.; Murillo Quijada, J. A.; Murray, W. J.; Musheghyan, H.; Musto, E.; Myagkov, A. G.; Myska, M.; Nachman, B. P.; Nackenhorst, O.; Nadal, J.; Nagai, K.; Nagai, R.; Nagai, Y.; Nagano, K.; Nagarkar, A.; Nagasaka, Y.; Nagata, K.; Nagel, M.; Nagy, E.; Nairz, A. M.; Nakahama, Y.; Nakamura, K.; Nakamura, T.; Nakano, I.; Namasivayam, H.; Naranjo Garcia, R. F.; Narayan, R.; Narrias Villar, D. I.; Naumann, T.; Navarro, G.; Nayyar, R.; Neal, H. A.; Nechaeva, P. Yu.; Neep, T. J.; Nef, P. D.; Negri, A.; Negrini, M.; Nektarijevic, S.; Nellist, C.; Nelson, A.; Nemecek, S.; Nemethy, P.; Nepomuceno, A. A.; Nessi, M.; Neubauer, M. S.; Neumann, M.; Neves, R. M.; Nevski, P.; Newman, P. R.; Nguyen, D. H.; Nickerson, R. B.; Nicolaidou, R.; Nicquevert, B.; Nielsen, J.; Nikiforou, N.; Nikiforov, A.; Nikolaenko, V.; Nikolic-Audit, I.; Nikolopoulos, K.; Nilsen, J. K.; Nilsson, P.; Ninomiya, Y.; Nisati, A.; Nisius, R.; Nobe, T.; Nomachi, M.; Nomidis, I.; Nooney, T.; Norberg, S.; Nordberg, M.; Novgorodova, O.; Nowak, S.; Nozaki, M.; Nozka, L.; Ntekas, K.; Nunes Hanninger, G.; Nunnemann, T.; Nurse, E.; Nuti, F.; O'Brien, B. J.; O'grady, F.; O'Neil, D. C.; O'Shea, V.; Oakham, F. G.; Oberlack, H.; Obermann, T.; Ocariz, J.; Ochi, A.; Ochoa, I.; Ochoa-Ricoux, J. P.; Oda, S.; Odaka, S.; Ogren, H.; Oh, A.; Oh, S. H.; Ohm, C. C.; Ohman, H.; Oide, H.; Okamura, W.; Okawa, H.; Okumura, Y.; Okuyama, T.; Olariu, A.; Olivares Pino, S. A.; Oliveira Damazio, D.; Oliver Garcia, E.; Olszewski, A.; Olszowska, J.; Onofre, A.; Onogi, K.; Onyisi, P. U. E.; Oram, C. J.; Oreglia, M. J.; Oren, Y.; Orestano, D.; Orlando, N.; Oropeza Barrera, C.; Orr, R. S.; Osculati, B.; Ospanov, R.; Otero y Garzon, G.; Otono, H.; Ouchrif, M.; Ould-Saada, F.; Ouraou, A.; Oussoren, K. P.; Ouyang, Q.; Ovcharova, A.; Owen, M.; Owen, R. E.; Ozcan, V. E.; Ozturk, N.; Pachal, K.; Pacheco Pages, A.; Padilla Aranda, C.; Pagáčová, M.; Pagan Griso, S.; Paganis, E.; Paige, F.; Pais, P.; Pajchel, K.; Palacino, G.; Palestini, S.; Palka, M.; Pallin, D.; Palma, A.; Pan, Y. B.; Panagiotopoulou, E.; Pandini, C. E.; Panduro Vazquez, J. G.; Pani, P.; Panitkin, S.; Pantea, D.; Paolozzi, L.; Papadopoulou, Th. D.; Papageorgiou, K.; Paramonov, A.; Paredes Hernandez, D.; Parker, M. A.; Parker, K. A.; Parodi, F.; Parsons, J. A.; Parzefall, U.; Pasqualucci, E.; Passaggio, S.; Pastore, F.; Pastore, Fr.; Pásztor, G.; Pataraia, S.; Patel, N. D.; Pater, J. R.; Pauly, T.; Pearce, J.; Pearson, B.; Pedersen, L. E.; Pedersen, M.; Pedraza Lopez, S.; Pedro, R.; Peleganchuk, S. V.; Pelikan, D.; Penc, O.; Peng, C.; Peng, H.; Penning, B.; Penwell, J.; Perepelitsa, D. V.; Perez Codina, E.; Pérez García-Estañ, M. T.; Perini, L.; Pernegger, H.; Perrella, S.; Peschke, R.; Peshekhonov, V. D.; Peters, K.; Peters, R. F. Y.; Petersen, B. A.; Petersen, T. C.; Petit, E.; Petridis, A.; Petridou, C.; Petroff, P.; Petrolo, E.; Petrucci, F.; Pettersson, N. E.; Pezoa, R.; Phillips, P. W.; Piacquadio, G.; Pianori, E.; Picazio, A.; Piccaro, E.; Piccinini, M.; Pickering, M. A.; Piegaia, R.; Pignotti, D. T.; Pilcher, J. E.; Pilkington, A. D.; Pina, J.; Pinamonti, M.; Pinfold, J. L.; Pingel, A.; Pires, S.; Pirumov, H.; Pitt, M.; Pizio, C.; Plazak, L.; Pleier, M.-A.; Pleskot, V.; Plotnikova, E.; Plucinski, P.; Pluth, D.; Poettgen, R.; Poggioli, L.; Pohl, D.; Polesello, G.; Poley, A.; Policicchio, A.; Polifka, R.; Polini, A.; Pollard, C. S.; Polychronakos, V.; Pommès, K.; Pontecorvo, L.; Pope, B. G.; Popeneciu, G. A.; Popovic, D. S.; Poppleton, A.; Pospisil, S.; Potamianos, K.; Potrap, I. N.; Potter, C. J.; Potter, C. T.; Poulard, G.; Poveda, J.; Pozdnyakov, V.; Pralavorio, P.; Pranko, A.; Prasad, S.; Prell, S.; Price, D.; Price, L. E.; Primavera, M.; Prince, S.; Proissl, M.; Prokofiev, K.; Prokoshin, F.; Protopapadaki, E.; Protopopescu, S.; Proudfoot, J.; Przybycien, M.; Ptacek, E.; Puddu, D.; Pueschel, E.; Puldon, D.; Purohit, M.; Puzo, P.; Qian, J.; Qin, G.; Qin, Y.; Quadt, A.; Quarrie, D. R.; Quayle, W. B.; Queitsch-Maitland, M.; Quilty, D.; Raddum, S.; Radeka, V.; Radescu, V.; Radhakrishnan, S. K.; Radloff, P.; Rados, P.; Ragusa, F.; Rahal, G.; Rajagopalan, S.; Rammensee, M.; Rangel-Smith, C.; Rauscher, F.; Rave, S.; Ravenscroft, T.; Raymond, M.; Read, A. L.; Readioff, N. P.; Rebuzzi, D. M.; Redelbach, A.; Redlinger, G.; Reece, R.; Reeves, K.; Rehnisch, L.; Reichert, J.; Reisin, H.; Relich, M.; Rembser, C.; Ren, H.; Renaud, A.; Rescigno, M.; Resconi, S.; Rezanova, O. L.; Reznicek, P.; Rezvani, R.; Richter, R.; Richter, S.; Richter-Was, E.; Ricken, O.; Ridel, M.; Rieck, P.; Riegel, C. J.; Rieger, J.; Rifki, O.; Rijssenbeek, M.; Rimoldi, A.; Rinaldi, L.; Ristić, B.; Ritsch, E.; Riu, I.; Rizatdinova, F.; Rizvi, E.; Robertson, S. H.; Robichaud-Veronneau, A.; Robinson, D.; Robinson, J. E. M.; Robson, A.; Roda, C.; Roe, S.; Røhne, O.; Rolli, S.; Romaniouk, A.; Romano, M.; Romano Saez, S. M.; Romero Adam, E.; Rompotis, N.; Ronzani, M.; Roos, L.; Ros, E.; Rosati, S.; Rosbach, K.; Rose, P.; Rosendahl, P. L.; Rosenthal, O.; Rossetti, V.; Rossi, E.; Rossi, L. P.; Rosten, J. H. N.; Rosten, R.; Rotaru, M.; Roth, I.; Rothberg, J.; Rousseau, D.; Royon, C. R.; Rozanov, A.; Rozen, Y.; Ruan, X.; Rubbo, F.; Rubinskiy, I.; Rud, V. I.; Rudolph, C.; Rudolph, M. S.; Rühr, F.; Ruiz-Martinez, A.; Rurikova, Z.; Rusakovich, N. A.; Ruschke, A.; Russell, H. L.; Rutherfoord, J. P.; Ruthmann, N.; Ryabov, Y. F.; Rybar, M.; Rybkin, G.; Ryder, N. C.; Saavedra, A. F.; Sabato, G.; Sacerdoti, S.; Saddique, A.; Sadrozinski, H. F.-W.; Sadykov, R.; Safai Tehrani, F.; Sahinsoy, M.; Saimpert, M.; Saito, T.; Sakamoto, H.; Sakurai, Y.; Salamanna, G.; Salamon, A.; Salazar Loyola, J. E.; Saleem, M.; Salek, D.; Sales De Bruin, P. H.; Salihagic, D.; Salnikov, A.; Salt, J.; Salvatore, D.; Salvatore, F.; Salvucci, A.; Salzburger, A.; Sammel, D.; Sampsonidis, D.; Sanchez, A.; Sánchez, J.; Sanchez Martinez, V.; Sandaker, H.; Sandbach, R. L.; Sander, H. G.; Sanders, M. P.; Sandhoff, M.; Sandoval, C.; Sandstroem, R.; Sankey, D. P. C.; Sannino, M.; Sansoni, A.; Santoni, C.; Santonico, R.; Santos, H.; Santoyo Castillo, I.; Sapp, K.; Sapronov, A.; Saraiva, J. G.; Sarrazin, B.; Sasaki, O.; Sasaki, Y.; Sato, K.; Sauvage, G.; Sauvan, E.; Savage, G.; Savard, P.; Sawyer, C.; Sawyer, L.; Saxon, J.; Sbarra, C.; Sbrizzi, A.; Scanlon, T.; Scannicchio, D. A.; Scarcella, M.; Scarfone, V.; Schaarschmidt, J.; Schacht, P.; Schaefer, D.; Schaefer, R.; Schaeffer, J.; Schaepe, S.; Schaetzel, S.; Schäfer, U.; Schaffer, A. C.; Schaile, D.; Schamberger, R. D.; Scharf, V.; Schegelsky, V. A.; Scheirich, D.; Schernau, M.; Schiavi, C.; Schillo, C.; Schioppa, M.; Schlenker, S.; Schmieden, K.; Schmitt, C.; Schmitt, S.; Schmitt, S.; Schneider, B.; Schnellbach, Y. J.; Schnoor, U.; Schoeffel, L.; Schoening, A.; Schoenrock, B. D.; Schopf, E.; Schorlemmer, A. L. S.; Schott, M.; Schouten, D.; Schovancova, J.; Schramm, S.; Schreyer, M.; Schroeder, C.; Schuh, N.; Schultens, M. J.; Schultz-Coulon, H.-C.; Schulz, H.; Schumacher, M.; Schumm, B. A.; Schune, Ph.; Schwanenberger, C.; Schwartzman, A.; Schwarz, T. A.; Schwegler, Ph.; Schweiger, H.; Schwemling, Ph.; Schwienhorst, R.; Schwindling, J.; Schwindt, T.; Sciacca, F. G.; Scifo, E.; Sciolla, G.; Scuri, F.; Scutti, F.; Searcy, J.; Sedov, G.; Sedykh, E.; Seema, P.; Seidel, S. C.; Seiden, A.; Seifert, F.; Seixas, J. M.; Sekhniaidze, G.; Sekhon, K.; Sekula, S. J.; Seliverstov, D. M.; Semprini-Cesari, N.; Serfon, C.; Serin, L.; Serkin, L.; Serre, T.; Sessa, M.; Seuster, R.; Severini, H.; Sfiligoj, T.; Sforza, F.; Sfyrla, A.; Shabalina, E.; Shamim, M.; Shan, L. Y.; Shang, R.; Shank, J. T.; Shapiro, M.; Shatalov, P. B.; Shaw, K.; Shaw, S. M.; Shcherbakova, A.; Shehu, C. Y.; Sherwood, P.; Shi, L.; Shimizu, S.; Shimmin, C. O.; Shimojima, M.; Shiyakova, M.; Shmeleva, A.; Shoaleh Saadi, D.; Shochet, M. J.; Shojaii, S.; Shrestha, S.; Shulga, E.; Shupe, M. A.; Shushkevich, S.; Sicho, P.; Sidebo, P. E.; Sidiropoulou, O.; Sidorov, D.; Sidoti, A.; Siegert, F.; Sijacki, Dj.; Silva, J.; Silver, Y.; Silverstein, S. B.; Simak, V.; Simard, O.; Simic, Lj.; Simion, S.; Simioni, E.; Simmons, B.; Simon, D.; Sinervo, P.; Sinev, N. B.; Sioli, M.; Siragusa, G.; Sisakyan, A. N.; Sivoklokov, S. Yu.; Sjölin, J.; Sjursen, T. B.; Skinner, M. B.; Skottowe, H. P.; Skubic, P.; Slater, M.; Slavicek, T.; Slawinska, M.; Sliwa, K.; Smakhtin, V.; Smart, B. H.; Smestad, L.; Smirnov, S. Yu.; Smirnov, Y.; Smirnova, L. N.; Smirnova, O.; Smith, M. N. K.; Smith, R. W.; Smizanska, M.; Smolek, K.; Snesarev, A. A.; Snidero, G.; Snyder, S.; Sobie, R.; Socher, F.; Soffer, A.; Soh, D. A.; Sokhrannyi, G.; Solans, C. A.; Solar, M.; Solc, J.; Soldatov, E. Yu.; Soldevila, U.; Solodkov, A. A.; Soloshenko, A.; Solovyanov, O. V.; Solovyev, V.; Sommer, P.; Song, H. Y.; Soni, N.; Sood, A.; Sopczak, A.; Sopko, B.; Sopko, V.; Sorin, V.; Sosa, D.; Sosebee, M.; Sotiropoulou, C. L.; Soualah, R.; Soukharev, A. M.; South, D.; Sowden, B. C.; Spagnolo, S.; Spalla, M.; Spangenberg, M.; Spanò, F.; Spearman, W. R.; Sperlich, D.; Spettel, F.; Spighi, R.; Spigo, G.; Spiller, L. A.; Spousta, M.; Spreitzer, T.; St. Denis, R. D.; Stabile, A.; Staerz, S.; Stahlman, J.; Stamen, R.; Stamm, S.; Stanecka, E.; Stanescu, C.; Stanescu-Bellu, M.; Stanitzki, M. M.; Stapnes, S.; Starchenko, E. A.; Stark, J.; Staroba, P.; Starovoitov, P.; Staszewski, R.; Steinberg, P.; Stelzer, B.; Stelzer, H. J.; Stelzer-Chilton, O.; Stenzel, H.; Stewart, G. A.; Stillings, J. A.; Stockton, M. C.; Stoebe, M.; Stoicea, G.; Stolte, P.; Stonjek, S.; Stradling, A. R.; Straessner, A.; Stramaglia, M. E.; Strandberg, J.; Strandberg, S.; Strandlie, A.; Strauss, E.; Strauss, M.; Strizenec, P.; Ströhmer, R.; Strom, D. M.; Stroynowski, R.; Strubig, A.; Stucci, S. A.; Stugu, B.; Styles, N. A.; Su, D.; Su, J.; Subramaniam, R.; Succurro, A.; Sugaya, Y.; Suk, M.; Sulin, V. V.; Sultansoy, S.; Sumida, T.; Sun, S.; Sun, X.; Sundermann, J. E.; Suruliz, K.; Susinno, G.; Sutton, M. R.; Suzuki, S.; Svatos, M.; Swiatlowski, M.; Sykora, I.; Sykora, T.; Ta, D.; Taccini, C.; Tackmann, K.; Taenzer, J.; Taffard, A.; Tafirout, R.; Taiblum, N.; Takai, H.; Takashima, R.; Takeda, H.; Takeshita, T.; Takubo, Y.; Talby, M.; Talyshev, A. A.; Tam, J. Y. C.; Tan, K. G.; Tanaka, J.; Tanaka, R.; Tanaka, S.; Tannenwald, B. B.; Tannoury, N.; Tapprogge, S.; Tarem, S.; Tarrade, F.; Tartarelli, G. F.; Tas, P.; Tasevsky, M.; Tashiro, T.; Tassi, E.; Tavares Delgado, A.; Tayalati, Y.; Taylor, F. E.; Taylor, G. N.; Taylor, P. T. E.; Taylor, W.; Teischinger, F. A.; Teixeira Dias Castanheira, M.; Teixeira-Dias, P.; Temming, K. K.; Temple, D.; Ten Kate, H.; Teng, P. K.; Teoh, J. J.; Tepel, F.; Terada, S.; Terashi, K.; Terron, J.; Terzo, S.; Testa, M.; Teuscher, R. J.; Theveneaux-Pelzer, T.; Thomas, J. P.; Thomas-Wilsker, J.; Thompson, E. N.; Thompson, P. D.; Thompson, R. J.; Thompson, A. S.; Thomsen, L. A.; Thomson, E.; Thomson, M.; Thun, R. P.; Tibbetts, M. J.; Ticse Torres, R. E.; Tikhomirov, V. O.; Tikhonov, Yu. A.; Timoshenko, S.; Tiouchichine, E.; Tipton, P.; Tisserant, S.; Todome, K.; Todorov, T.; Todorova-Nova, S.; Tojo, J.; Tokár, S.; Tokushuku, K.; Tollefson, K.; Tolley, E.; Tomlinson, L.; Tomoto, M.; Tompkins, L.; Toms, K.; Torrence, E.; Torres, H.; Torró Pastor, E.; Toth, J.; Touchard, F.; Tovey, D. R.; Trefzger, T.; Tremblet, L.; Tricoli, A.; Trigger, I. M.; Trincaz-Duvoid, S.; Tripiana, M. F.; Trischuk, W.; Trocmé, B.; Troncon, C.; Trottier-McDonald, M.; Trovatelli, M.; Truong, L.; Trzebinski, M.; Trzupek, A.; Tsarouchas, C.; Tseng, J. C.-L.; Tsiareshka, P. V.; Tsionou, D.; Tsipolitis, G.; Tsirintanis, N.; Tsiskaridze, S.; Tsiskaridze, V.; Tskhadadze, E. G.; Tsukerman, I. I.; Tsulaia, V.; Tsuno, S.; Tsybychev, D.; Tudorache, A.; Tudorache, V.; Tuna, A. N.; Tupputi, S. A.; Turchikhin, S.; Turecek, D.; Turra, R.; Turvey, A. J.; Tuts, P. M.; Tykhonov, A.; Tylmad, M.; Tyndel, M.; Ueda, I.; Ueno, R.; Ughetto, M.; Ugland, M.; Ukegawa, F.; Unal, G.; Undrus, A.; Unel, G.; Ungaro, F. C.; Unno, Y.; Unverdorben, C.; Urban, J.; Urquijo, P.; Urrejola, P.; Usai, G.; Usanova, A.; Vacavant, L.; Vacek, V.; Vachon, B.; Valderanis, C.; Valencic, N.; Valentinetti, S.; Valero, A.; Valery, L.; Valkar, S.; Valladolid Gallego, E.; Vallecorsa, S.; Valls Ferrer, J. A.; Van Den Wollenberg, W.; Van Der Deijl, P. C.; van der Geer, R.; van der Graaf, H.; van Eldik, N.; van Gemmeren, P.; Van Nieuwkoop, J.; van Vulpen, I.; van Woerden, M. C.; Vanadia, M.; Vandelli, W.; Vanguri, R.; Vaniachine, A.; Vannucci, F.; Vardanyan, G.; Vari, R.; Varnes, E. W.; Varol, T.; Varouchas, D.; Vartapetian, A.; Varvell, K. E.; Vazeille, F.; Vazquez Schroeder, T.; Veatch, J.; Veloce, L. M.; Veloso, F.; Velz, T.; Veneziano, S.; Ventura, A.; Ventura, D.; Venturi, M.; Venturi, N.; Venturini, A.; Vercesi, V.; Verducci, M.; Verkerke, W.; Vermeulen, J. C.; Vest, A.; Vetterli, M. C.; Viazlo, O.; Vichou, I.; Vickey, T.; Vickey Boeriu, O. E.; Viehhauser, G. H. A.; Viel, S.; Vigne, R.; Villa, M.; Villaplana Perez, M.; Vilucchi, E.; Vincter, M. G.; Vinogradov, V. B.; Vivarelli, I.; Vives Vaque, F.; Vlachos, S.; Vladoiu, D.; Vlasak, M.; Vogel, M.; Vokac, P.; Volpi, G.; Volpi, M.; von der Schmitt, H.; von Radziewski, H.; von Toerne, E.; Vorobel, V.; Vorobev, K.; Vos, M.; Voss, R.; Vossebeld, J. H.; Vranjes, N.; Vranjes Milosavljevic, M.; Vrba, V.; Vreeswijk, M.; Vuillermet, R.; Vukotic, I.; Vykydal, Z.; Wagner, P.; Wagner, W.; Wahlberg, H.; Wahrmund, S.; Wakabayashi, J.; Walder, J.; Walker, R.; Walkowiak, W.; Wang, C.; Wang, F.; Wang, H.; Wang, H.; Wang, J.; Wang, J.; Wang, K.; Wang, R.; Wang, S. M.; Wang, T.; Wang, T.; Wang, X.; Wanotayaroj, C.; Warburton, A.; Ward, C. P.; Wardrope, D. R.; Washbrook, A.; Wasicki, C.; Watkins, P. M.; Watson, A. T.; Watson, I. J.; Watson, M. F.; Watts, G.; Watts, S.; Waugh, B. M.; Webb, S.; Weber, M. S.; Weber, S. W.; Webster, J. S.; Weidberg, A. R.; Weinert, B.; Weingarten, J.; Weiser, C.; Weits, H.; Wells, P. S.; Wenaus, T.; Wengler, T.; Wenig, S.; Wermes, N.; Werner, M.; Werner, P.; Wessels, M.; Wetter, J.; Whalen, K.; Wharton, A. M.; White, A.; White, M. J.; White, R.; White, S.; Whiteson, D.; Wickens, F. J.; Wiedenmann, W.; Wielers, M.; Wienemann, P.; Wiglesworth, C.; Wiik-Fuchs, L. A. M.; Wildauer, A.; Wilkens, H. G.; Williams, H. H.; Williams, S.; Willis, C.; Willocq, S.; Wilson, A.; Wilson, J. A.; Wingerter-Seez, I.; Winklmeier, F.; Winter, B. T.; Wittgen, M.; Wittkowski, J.; Wollstadt, S. J.; Wolter, M. W.; Wolters, H.; Wosiek, B. K.; Wotschack, J.; Woudstra, M. J.; Wozniak, K. W.; Wu, M.; Wu, M.; Wu, S. L.; Wu, X.; Wu, Y.; Wyatt, T. R.; Wynne, B. M.; Xella, S.; Xu, D.; Xu, L.; Yabsley, B.; Yacoob, S.; Yakabe, R.; Yamada, M.; Yamaguchi, D.; Yamaguchi, Y.; Yamamoto, A.; Yamamoto, S.; Yamanaka, T.; Yamauchi, K.; Yamazaki, Y.; Yan, Z.; Yang, H.; Yang, H.; Yang, Y.; Yao, W.-M.; Yasu, Y.; Yatsenko, E.; Yau Wong, K. H.; Ye, J.; Ye, S.; Yeletskikh, I.; Yen, A. L.; Yildirim, E.; Yorita, K.; Yoshida, R.; Yoshihara, K.; Young, C.; Young, C. J. S.; Youssef, S.; Yu, D. R.; Yu, J.; Yu, J. M.; Yu, J.; Yuan, L.; Yuen, S. P. Y.; Yurkewicz, A.; Yusuff, I.; Zabinski, B.; Zaidan, R.; Zaitsev, A. M.; Zalieckas, J.; Zaman, A.; Zambito, S.; Zanello, L.; Zanzi, D.; Zeitnitz, C.; Zeman, M.; Zemla, A.; Zeng, Q.; Zengel, K.; Zenin, O.; Ženiš, T.; Zerwas, D.; Zhang, D.; Zhang, F.; Zhang, H.; Zhang, J.; Zhang, L.; Zhang, R.; Zhang, X.; Zhang, Z.; Zhao, X.; Zhao, Y.; Zhao, Z.; Zhemchugov, A.; Zhong, J.; Zhou, B.; Zhou, C.; Zhou, L.; Zhou, L.; Zhou, M.; Zhou, N.; Zhu, C. G.; Zhu, H.; Zhu, J.; Zhu, Y.; Zhuang, X.; Zhukov, K.; Zibell, A.; Zieminska, D.; Zimine, N. I.; Zimmermann, C.; Zimmermann, S.; Zinonos, Z.; Zinser, M.; Ziolkowski, M.; Živković, L.; Zobernig, G.; Zoccoli, A.; zur Nedden, M.; Zurzolo, G.; Zwalinski, L.

2016-01-01

A search for a high-mass Higgs boson H is performed in the H → WW → ℓνℓν and H → WW → ℓνqq decay channels using pp collision data corresponding to an integrated luminosity of 20.3 fb-1 collected at √{s}=8 TeV by the ATLAS detector at the Large Hadron Collider. No evidence of a high-mass Higgs boson is found. Limits on σ H × BR( H → WW) as a function of the Higgs boson mass m H are determined in three different scenarios: one in which the heavy Higgs boson has a narrow width compared to the experimental resolution, one for a width increasing with the boson mass and modeled by the complex-pole scheme following the same behavior as in the Standard Model, and one for intermediate widths. The upper range of the search is m H = 1500 GeV for the narrow-width scenario and m H = 1000 GeV for the other two scenarios. The lower edge of the search range is 200-300 GeV and depends on the analysis channel and search scenario. For each signal interpretation, individual and combined limits from the two WW decay channels are presented. At m H = 1500 GeV, the highest-mass point tested, σ H × BR( H → WW) for a narrow-width Higgs boson is constrained to be less than 22 fb and 6.6 fb at 95% CL for the gluon fusion and vector-boson fusion production modes, respectively. [Figure not available: see fulltext.

Search for a high-mass Higgs boson decaying to a W boson pair in pp collisions at √s = 8 TeV with the ATLAS detector

DOE PAGES

Aad, G.; Abbott, B.; Abdallah, J.; ...

2016-01-07

A search for a high-mass Higgs boson H is performed in the H → WW → ℓνℓν and H → WW → ℓνqq decay channels using pp collision data corresponding to an integrated luminosity of 20.3 fb -1 collected at √s = 8 TeV by the ATLAS detector at the Large Hadron Collider. No evidence of a high-mass Higgs boson is found. Limits on σ H × BR(H → WW) as a function of the Higgs boson mass m H are determined in three different scenarios: one in which the heavy Higgs boson has a narrow width compared to themore » experimental resolution, one for a width increasing with the boson mass and modeled by the complex-pole scheme following the same behavior as in the Standard Model, and one for intermediate widths. The upper range of the search is m H = 1500 GeV for the narrow-width scenario and m H = 1000 GeV for the other two scenarios. The lower edge of the search range is 200–300 GeV and depends on the analysis channel and search scenario. For each signal interpretation, individual and combined limits from the two WW decay channels are presented. Thus, at m H = 1500 GeV, the highest-mass point tested, σ H × BR(H → WW) for a narrow-width Higgs boson is constrained to be less than 22fb and 6.6fb at 95% CL for the gluon fusion and vector-boson fusion production modes, respectively.« less

Liquid Acquisition Device Design Sensitivity Study

NASA Technical Reports Server (NTRS)

VanDyke, M. K.; Hastings, L. J.

2012-01-01

In-space propulsion often necessitates the use of a capillary liquid acquisition device (LAD) to assure that gas-free liquid propellant is available to support engine restarts in microgravity. If a capillary screen-channel device is chosen, then the designer must determine the appropriate combination screen mesh and channel geometry. A screen mesh selection which results in the smallest LAD width when compared to any other screen candidate (for a constant length) is desirable; however, no best screen exists for all LAD design requirements. Flow rate, percent fill, and acceleration are the most influential drivers for determining screen widths. Increased flow rates and reduced percent fills increase the through-the-screen flow pressure losses, which drive the LAD to increased widths regardless of screen choice. Similarly, increased acceleration levels and corresponding liquid head pressures drive the screen mesh selection toward a higher bubble point (liquid retention capability). After ruling out some screens on the basis of acceleration requirements alone, candidates can be identified by examining screens with small flow-loss-to-bubble point ratios for a given condition (i.e., comparing screens at certain flow rates and fill levels). Within the same flow rate and fill level, the screen constants inertia resistance coefficient, void fraction, screen pore or opening diameter, and bubble point can become the driving forces in identifying the smaller flow-loss-to-bubble point ratios.

Ultrasonic alignment of bio-functionalized magnetic beads and live cells in PDMS micro-fluidic channel.

PubMed

Islam, Afroja T; Siddique, Ariful H; Ramulu, T S; Reddy, Venu; Eu, Young-Jae; Cho, Seung Hyun; Kim, CheolGi

2012-12-01

In this work, we demonstrated the alignment of polystyrene latex microspheres (diameter of 1 ~45 μm), bio-functionalized superparamagnetic beads (diameter 2.8 μm), and live cells (average diameter 1 ~2 μm) using an ultrasonic standing wave (USW) in a PDMS microfluidic channel (330 μm width) attached on a Si substrate for bio-medical applications. To generate a standing wave inside the channel, ultrasound of 2.25 MHz resonance frequency (for the channel width) was applied by two ultrasound transducers installed at both sides of the channel which caused the radiation force to concentrate the micro-particles at the single pressure nodal plane of USW. By increasing the frequency to the next resonance condition of the channel, the particles were concentrated in dual nodal planes. Migration time of the micro-particles towards the single nodal plane was recorded as 108 s, 17 s, and 115 s for polystyrene particles of 2 μm diameter, bio-functionalized magnetic beads, and live cells, respectively. These successful alignments of the bio-functionalized magnetic beads along the desired part of the channel can enhance the performance of a sensor which is applicable for the bio-hybrid system and the alignment of live cells without any damage can be used for sample pre-treatment for the application of lab-on-a-chip type bioassays.

Network Structure as a Modulator of Disturbance Impacts in Streams

NASA Astrophysics Data System (ADS)

Warner, S.; Tullos, D. D.

2017-12-01

This study examines how river network structure affects the propagation of geomorphic and anthropogenic disturbances through streams. Geomorphic processes such as debris flows can alter channel morphology and modify habitat for aquatic biota. Anthropogenic disturbances such as road construction can interact with the geomorphology and hydrology of forested watersheds to change sediment and water inputs to streams. It was hypothesized that the network structure of streams within forested watersheds would influence the location and magnitude of the impacts of debris flows and road construction on sediment size and channel width. Longitudinal surveys were conducted every 50 meters for 11 kilometers of third-to-fifth order streams in the H.J. Andrews Experimental Forest in the Western Cascade Range of Oregon. Particle counts and channel geometry measurements were collected to characterize the geomorphic impacts of road crossings and debris flows as disturbances. Sediment size distributions and width measurements were plotted against the distance of survey locations through the network to identify variations in longitudinal trends of channel characteristics. Thresholds for the background variation in sediment size and channel width, based on the standard deviations of sample points, were developed for sampled stream segments characterized by location as well as geomorphic and land use history. Survey locations were classified as "disturbed" when they deviated beyond the reference thresholds in expected sediment sizes and channel widths, as well as flow-connected proximity to debris flows and road crossings. River network structure was quantified by drainage density and centrality of nodes upstream of survey locations. Drainage density and node centrality were compared between survey locations with similar channel characteristic classifications. Cluster analysis was used to assess the significance of survey location, proximity of survey location to debris flows and road crossings, drainage density and node centrality in predicting sediment size and channel width classifications for locations within the watershed. Results contribute to the understanding of susceptibility and responses of streams supporting critical habitat for aquatic species to debris flows and forest road disturbances.

Kv1.1 channelopathy abolishes presynaptic spike width modulation by subthreshold somatic depolarization

PubMed Central

Vivekananda, Umesh; Novak, Pavel; Bello, Oscar D.; Korchev, Yuri E.; Krishnakumar, Shyam S.; Volynski, Kirill E.; Kullmann, Dimitri M.

2017-01-01

Although action potentials propagate along axons in an all-or-none manner, subthreshold membrane potential fluctuations at the soma affect neurotransmitter release from synaptic boutons. An important mechanism underlying analog–digital modulation is depolarization-mediated inactivation of presynaptic Kv1-family potassium channels, leading to action potential broadening and increased calcium influx. Previous studies have relied heavily on recordings from blebs formed after axon transection, which may exaggerate the passive propagation of somatic depolarization. We recorded instead from small boutons supplied by intact axons identified with scanning ion conductance microscopy in primary hippocampal cultures and asked how distinct potassium channels interact in determining the basal spike width and its modulation by subthreshold somatic depolarization. Pharmacological or genetic deletion of Kv1.1 broadened presynaptic spikes without preventing further prolongation by brief depolarizing somatic prepulses. A heterozygous mouse model of episodic ataxia type 1 harboring a dominant Kv1.1 mutation had a similar broadening effect on basal spike shape as deletion of Kv1.1; however, spike modulation by somatic prepulses was abolished. These results argue that the Kv1.1 subunit is not necessary for subthreshold modulation of spike width. However, a disease-associated mutant subunit prevents the interplay of analog and digital transmission, possibly by disrupting the normal stoichiometry of presynaptic potassium channels. PMID:28193892

Strong decays of DJ(3000 ) and Ds J(3040 )

NASA Astrophysics Data System (ADS)

Li, Si-Chen; Wang, Tianhong; Jiang, Yue; Tan, Xiao-Ze; Li, Qiang; Wang, Guo-Li; Chang, Chao-Hsi

2018-03-01

In this paper, we systematically calculate two-body strong decays of newly observed DJ(3000 ) and Ds J(3040 ) with 2 P (1+) and 2 P (1+') assignments in an instantaneous approximation of the Bethe-Salpeter equation method. Our results show that both resonances can be explained as the 2 P (1+') with broad width via 3P1 and 1P1 mixing in D and Ds families. For DJ(3000 ), the total width is 229.6 MeV in our calculation, close to the upper limit of experimental data, and the dominant decay channels are D2*π , D*π , and D*(2600 )π . For Ds J(3040 ), the total width is 157.4 MeV in our calculation, close to the lower limit of experimental data, and the dominant channels are D*K and D*K*. These results are consistent with observed channels in experiments. Given the very little information that has been obtained from experiments and the large error bars of the total decay widths, we recommend the detection of dominant channels in our calculation.

Viscosity and Wetting Property of Water Confined in Extended Nanospace Simultaneously Measured from Highly-Pressurized Meniscus Motion.

PubMed

Li, Lixiao; Kazoe, Yutaka; Mawatari, Kazuma; Sugii, Yasuhiko; Kitamori, Takehiko

2012-09-06

Understanding fluid and interfacial properties in extended nanospace (10-1000 nm) is important for recent advances of nanofluidics. We studied properties of water confined in fused-silica nanochannels of 50-1500 nm sizes with two types of cross-section: (1) square channel of nanoscale width and depth, and (2) plate channel of microscale width and nanoscale depth. Viscosity and wetting property were simultaneously measured from capillary filling controlled by megapascal external pressure. The viscosity increased in extended nanospace, while the wetting property was almost constant. Especially, water in the square nanochannels had much higher viscosity than the plate channel, which can be explained considering loosely coupled water molecules by hydrogen bond on the surface within 24 nm. This study suggests specificity of fluids two-dimensionally confined in extended nanoscale, in which the liquid is highly viscous by the specific water phase, while the wetting dynamics is governed by the well-known adsorbed water layer of several-molecules thickness.

A novel passive micromixer based on unbalanced splits and collisions of fluid streams

NASA Astrophysics Data System (ADS)

Ansari, Mubashshir Ahmad; Kim, Kwang-Yong; Anwar, Khalid; Kim, Sun Min

2010-05-01

A new passive micromixer based on the concept of unbalanced splits and cross-collisions of fluid streams is designed and fabricated. Experimental and numerical studies have been carried out on the micromixer at Reynolds numbers ranging from 10 to 80. The three-dimensional Navier-Stokes equations have been used to analyze the mixing and flow behavior of the micromixer, which is composed of two sub-channels of unequal widths which repeatedly undergo splitting and recombination. The difference between the mass flow rates in the two sub-channels creates an unbalanced collision of the two fluid streams. Mixing is mainly due to the combined effect of unbalanced collisions of the fluid streams and Dean vortices. The micromixer shows interesting mixing behavior for different ratios of the widths of the two split sub-channels. The sub-channels wherein the major sub-channel is twice as wide as the minor sub-channel exhibit the highest mixing performance at Reynolds numbers larger than 40. The results show the lowest mixing performance for the case of uniform width, where balanced collisions occur.

Mean annual runoff and peak flow estimates based on channel geometry of streams in northeastern and western Montana

USGS Publications Warehouse

Parrett, Charles; Omang, R.J.; Hull, J.A.

1983-01-01

Equations for estimating mean annual runoff and peak discharge from measurements of channel geometry were developed for western and northeastern Montana. The study area was divided into two regions for the mean annual runoff analysis, and separate multiple-regression equations were developed for each region. The active-channel width was determined to be the most important independent variable in each region. The standard error of estimate for the estimating equation using active-channel width was 61 percent in the Northeast Region and 38 percent in the West region. The study area was divided into six regions for the peak discharge analysis, and multiple regression equations relating channel geometry and basin characteristics to peak discharges having recurrence intervals of 2, 5, 10, 25, 50 and 100 years were developed for each region. The standard errors of estimate for the regression equations using only channel width as an independent variable ranged from 35 to 105 percent. The standard errors improved in four regions as basin characteristics were added to the estimating equations. (USGS)

Calibration of optical coherence tomography angiography with a microfluidic chip

NASA Astrophysics Data System (ADS)

Su, Johnny P.; Chandwani, Rahul; Gao, Simon S.; Pechauer, Alex D.; Zhang, Miao; Wang, Jie; Jia, Yali; Huang, David; Liu, Gangjun

2016-08-01

A microfluidic chip with microchannels ranging from 8 to 96 μm was used to mimic blood vessels down to the capillary level. Blood flow within the microfluidic channels was analyzed with split-spectrum amplitude-decorrelation angiography (SSADA)-based optical coherence tomography (OCT) angiography. It was found that the SSADA decorrelation value was related to both blood flow speed and channel width. SSADA could differentiate nonflowing blood inside the microfluidic channels from static paper. The SSADA decorrelation value was approximately linear with blood flow velocity up to a threshold Vsat of 5.83±1.33 mm/s (mean±standard deviation over the range of channel widths). Beyond this threshold, it approached a saturation value Dsat. Dsat was higher for wider channels, and approached a maximum value Dsm as the channel width became much larger than the beam focal spot diameter. These results indicate that decorrelation values (flow signal) in capillary networks would be proportional to both flow velocity and vessel caliber but would be capped at a saturation value in larger blood vessels. These findings are useful for interpretation and quantification of clinical OCT angiography results.

Rotating gravity currents. Part 1. Energy loss theory

NASA Astrophysics Data System (ADS)

Martin, J. R.; Lane-Serff, G. F.

2005-01-01

A comprehensive energy loss theory for gravity currents in rotating rectangular channels is presented. The model is an extension of the non-rotating energy loss theory of Benjamin (J. Fluid Mech. vol. 31, 1968, p. 209) and the steady-state dissipationless theory of rotating gravity currents of Hacker (PhD thesis, 1996). The theory assumes the fluid is inviscid, there is no shear within the current, and the Boussinesq approximation is made. Dissipation is introduced using a simple method. A head loss term is introduced into the Bernoulli equation and it is assumed that the energy loss is uniform across the stream. Conservation of momentum, volume flux and potential vorticity between upstream and downstream locations is then considered. By allowing for energy dissipation, results are obtained for channels of arbitrary depth and width (relative to the current). The results match those from earlier workers in the two limits of (i) zero rotation (but including dissipation) and (ii) zero dissipation (but including rotation). Three types of flow are identified as the effect of rotation increases, characterized in terms of the location of the outcropping interface between the gravity current and the ambient fluid on the channel boundaries. The parameters for transitions between these cases are quantified, as is the detailed behaviour of the flow in all cases. In particular, the speed of the current can be predicted for any given channel depth and width. As the channel depth increases, the predicted Froude number tends to surd 2, as for non-rotating flows.

Turning the tide: estuarine bars and mutually evasive ebb- and flood-dominated channels

NASA Astrophysics Data System (ADS)

Kleinhans, M. G.; Leuven, J.; van der Vegt, M.; Baar, A. W.; Braat, L.; Bergsma, L.; Weisscher, S.

2015-12-01

Estuaries have perpetually changing and interacting channels and shoals formed by ebb and flood currents, but we lack a descriptive taxonomy and forecasting model. We explore the hypotheses that the great variation of bar and shoal morphologies are explained by similar factors as river bars, namely channel aspect ratio, sediment mobility and limits on bar erosion and chute cutoff caused by cohesive sediment. Here we use remote sensing data and a novel tidal flume setup, the Metronome, to create estuaries or short estuarine reaches from idealized initial conditions, with and without mud supply at the fluvial boundary. Bar width-depth ratios in estuaries are similar to those in braided rivers. In unconfined (cohesionless) experimental estuaries, bar- and channel dynamics increase with increasing river discharge. Ebb- and flood-dominated channels are ubiquitous even in entirely straight sections. The apparent stability of ebb- and flood channels is partly explained by the inherent instability of symmetrical channel bifurcations as in rivers.

Characterization and evaluation of channel and hillslope erosion on the Zuni Indian Reservation, New Mexico, 1992-95

USGS Publications Warehouse

Gellis, A.C.

1998-01-01

Like many areas of the southwestern United States, the Zuni Indian Reservation, New Mexico, has high rates of erosion, ranging from 95 to greater than 1,430 cubic meters per square kilometer per year. Erosion on the Zuni Indian Reservation includes channel erosion (arroyo incision and channel widening) and hillslope (sheetwash) erosion. The U.S. Geological Survey conducted a 3-year (1992-95) study on channel erosion and hillslope erosion in the portion of the Rio Nutria watershed that drains entirely within the Zuni Indian Reservation. Results of the study can be used by the Zuni Tribe to develop a plan for watershed rehabilitation. Channel changes, gully growth, headcuts, and changes in dirt roads over time were examined to characterize and evaluate channel erosion in the Rio Nutria watershed. Channel cross-sectional changes included width, depth, width-to-depth ratio, area, and geometry. Relative rates of gully growth, headcuts, and changes in dirt roads over time were examined using aerial photographs. Results of resurveys conducted between 1992 and 1994 of 85 channel cross sections indicated aggradation of 72 percent of cross sections in three subbasins of the Rio Nutria watershed. Forty-eight percent of resurveyed cross sections showed an increase in cross-sectional area and erosion; nine of these are in tributaries. Some channels (43 percent) aggraded and increased in cross-sectional area. This increase in cross- sectional area is due mostly to widening. Channel widening is a more pervasive form of erosion than channel scour on the Zuni Indian Reservation. The tops of channels widened in 67 percent and the bottoms of channels widened in 44 percent of resurveyed cross sections. Narrow, deep triangular channels are more erosive than rectangular cross sections. Five land-cover types--three sites on mixed-grass pasture, two sites on sites on unchained pi?on and juniper, one site on sagebrush, one site on ponderosa pine, and two sites on chained pi?on and juniper--were each instrumented with sediment traps between 1992 and 1994 to measure hillslope erosion. Highest sediment yields were measured at chained areas and mixed- grass pasture. Annual yields from sites that were operated for more than a year were 11.7, 6.0, and 6.5 metric tons per square kilometer per year at a pi?on and juniper site, mixed-grass pasture site, and sagebrush site, respectively.

Ecoregions and stream morphology in eastern Oklahoma

USGS Publications Warehouse

Splinter, D.K.; Dauwalter, D.C.; Marston, R.A.; Fisher, W.L.

2010-01-01

Broad-scale variables (i.e., geology, topography, climate, land use, vegetation, and soils) influence channel morphology. How and to what extent the longitudinal pattern of channel morphology is influenced by broad-scale variables is important to fluvial geomorphologists and stream ecologists. In the last couple of decades, there has been an increase in the amount of interdisciplinary research between fluvial geomorphologists and stream ecologists. In a historical context, fluvial geomorphologists are more apt to use physiographic regions to distinguish broad-scale variables, while stream ecologists are more apt to use the concept of an ecosystem to address the broad-scale variables that influence stream habitat. For this reason, we designed a study using ecoregions, which uses physical and biological variables to understand how landscapes influence channel processes. Ecoregions are delineated by similarities in geology, climate, soils, land use, and potential natural vegetation. In the fluvial system, stream form and function are dictated by processes observed throughout the fluvial hierarchy. Recognizing that stream form and function should differ by ecoregion, a study was designed to evaluate how the characteristics of stream channels differed longitudinally among three ecoregions in eastern Oklahoma, USA: Boston Mountains, Ozark Highlands, and Ouachita Mountains. Channel morphology of 149 stream reaches was surveyed in 1st- through 4th-order streams, and effects of drainage area and ecoregion on channel morphology was evaluated using multiple regressions. Differences existed (?????0.05) among ecoregions for particle size, bankfull width, and width/depth ratio. No differences existed among ecoregions for gradient or sinuosity. Particle size was smallest in the Ozark Highlands and largest in the Ouachita Mountains. Bankfull width was larger in the Ozark Highlands than in the Boston Mountains and Ouachita Mountains in larger streams. Width/depth ratios of the Boston Mountains and Ozark Highlands were not statistically different. Significant differences existed, however, between the Boston Mountains and Ozark Highlands when compared individually to the Ouachita Mountains. We found that ecoregions afforded a good spatial structure that can help in understanding longitudinal trends in stream reach morphology surveyed at the reach scale. The hierarchy of the fluvial system begins within a broad, relatively homogenous setting that imparts control on processes that affect stream function. Ecoregions provide an adequate regional division to begin a large-scale geomorphic study of processes in stream channels. ?? 2010 Elsevier B.V.

Axially Tapered And Bilayer Microchannels For Evaporative Cooling Devices

DOEpatents

Nilson, Robert; Griffiths, Stewart

2005-10-04

The invention consists of an evaporative cooling device comprising one or more microchannels whose cross section is axially reduced to control the maximum capillary pressure differential between liquid and vapor phases. In one embodiment, the evaporation channels have a rectangular cross section that is reduced in width along a flow path. In another embodiment, channels of fixed width are patterned with an array of microfabricated post-like features such that the feature size and spacing are gradually reduced along the flow path. Other embodiments incorporate bilayer channels consisting of an upper cover plate having a pattern of slots or holes of axially decreasing size and a lower fluid flow layer having channel widths substantially greater than the characteristic microscale dimensions of the patterned cover plate. The small dimensions of the cover plate holes afford large capillary pressure differentials while the larger dimensions of the lower region reduce viscous flow resistance.

Using a Numerical Model to Assess the Geomorphic Impacts of Forest Management Scenarios on Streams

NASA Astrophysics Data System (ADS)

Davidson, S. L.; Eaton, B. C.

2014-12-01

In-stream large wood governs the morphology of many small to intermediate streams, while riparian vegetation influences bank strength and channel pattern. Forest management practices such as harvesting and fire suppression therefore dramatically influence channel processes and associated aquatic habitat. The primary objective of this research is to compare the impacts of three common forest scenarios - natural fire disturbance, forest harvesting with a riparian buffer, and fire suppression - on the volume of in-channel wood and the complexity of aquatic habitat in channels at a range of scales. Each scenario is explored through Monte Carlo simulations run over a period of 1000 years using a numerical reach scale channel simulator (RSCS), with variations in tree toppling rate and forest density used to represent each forest management trajectory. The habitat complexity associated with each scenario is assessed based on the area of the bed occupied by pools and spawning sized sediment, the availability of wood cover, and the probability of avulsion. Within the fire scenario, we also use the model to separately investigate the effects of root decay and recovery on equilibrium channel geometry by varying the rooting depth and associated bank strength through time. The results show that wood loading and habitat complexity are influenced by the timing and magnitude of wood recruitment, as well as channel scale. The forest harvesting scenario produces the lowest wood loads and habitat complexity so long as the buffer width is less than the average mature tree height. The natural fire cycle produces the greatest wood loading and habitat complexity, but also the greatest variability because these streams experience significant periods without wood recruitment as forests regenerate. In reaches that experience recurrent fires, width increases in the post-fire period as roots decay, at times producing a change in channel pattern when a threshold width to depth ratio is exceeded, and decreases as the forest regenerates. In all cases, the effects are greatest in small to intermediate sized streams where wood is the dominant driver of channel morphology, and become negligible in large streams governed by fluvial processes.

Ram-air sample collection device for a chemical warfare agent sensor

DOEpatents

Megerle, Clifford A.; Adkins, Douglas R.; Frye-Mason, Gregory C.

2002-01-01

In a surface acoustic wave sensor mounted within a body, the sensor having a surface acoustic wave array detector and a micro-fabricated sample preconcentrator exposed on a surface of the body, an apparatus for collecting air for the sensor, comprising a housing operatively arranged to mount atop the body, the housing including a multi-stage channel having an inlet and an outlet, the channel having a first stage having a first height and width proximate the inlet, a second stage having a second lower height and width proximate the micro-fabricated sample preconcentrator, a third stage having a still lower third height and width proximate the surface acoustic wave array detector, and a fourth stage having a fourth height and width proximate the outlet, where the fourth height and width are substantially the same as the first height and width.

Herbaceous versus forested riparian vegetation: narrow and simple versus wide, woody and diverse stream habitat

Treesearch

C.R. Jackson; D.S. Leigh; S.L. Scarbrough; J.F. Chamblee

2014-01-01

We investigated interactions of riparian vegetative conditions upon a suite of channel morphological variables: active channel width, variability of width within a reach, large wood frequency, mesoscale habitat distributions, mesoscale habitat diversity, median particle size and per cent fines. We surveyed 49 wadeable streams, 45 with low levels of development,...

A method for estimating mean and low flows of streams in national forests of Montana

USGS Publications Warehouse

Parrett, Charles; Hull, J.A.

1985-01-01

Equations were developed for estimating mean annual discharge, 80-percent exceedance discharge, and 95-percent exceedance discharge for streams on national forest lands in Montana. The equations for mean annual discharge used active-channel width, drainage area and mean annual precipitation as independent variables, with active-channel width being most significant. The equations for 80-percent exceedance discharge and 95-percent exceedance discharge used only active-channel width as an independent variable. The standard error or estimate for the best equation for estimating mean annual discharge was 27 percent. The standard errors of estimate for the equations were 67 percent for estimating 80-percent exceedance discharge and 75 percent for estimating 95-percent exceedance discharge. (USGS)

Generating multiplex gradients of biomolecules for controlling cellular adhesion in parallel microfluidic channels.

PubMed

Didar, Tohid Fatanat; Tabrizian, Maryam

2012-11-07

Here we present a microfluidic platform to generate multiplex gradients of biomolecules within parallel microfluidic channels, in which a range of multiplex concentration gradients with different profile shapes are simultaneously produced. Nonlinear polynomial gradients were also generated using this device. The gradient generation principle is based on implementing parrallel channels with each providing a different hydrodynamic resistance. The generated biomolecule gradients were then covalently functionalized onto the microchannel surfaces. Surface gradients along the channel width were a result of covalent attachments of biomolecules to the surface, which remained functional under high shear stresses (50 dyn/cm(2)). An IgG antibody conjugated to three different fluorescence dyes (FITC, Cy5 and Cy3) was used to demonstrate the resulting multiplex concentration gradients of biomolecules. The device enabled generation of gradients with up to three different biomolecules in each channel with varying concentration profiles. We were also able to produce 2-dimensional gradients in which biomolecules were distributed along the length and width of the channel. To demonstrate the applicability of the developed design, three different multiplex concentration gradients of REDV and KRSR peptides were patterned along the width of three parallel channels and adhesion of primary human umbilical vein endothelial cell (HUVEC) in each channel was subsequently investigated using a single chip.

Electroosmotic flow and ionic conductance in a pH-regulated rectangular nanochannel

NASA Astrophysics Data System (ADS)

Sadeghi, Morteza; Saidi, Mohammad Hassan; Sadeghi, Arman

2017-06-01

Infinite series solutions are obtained for electrical potential, electroosmotic velocity, ionic conductance, and surface physicochemical properties of long pH-regulated rectangular nanochannels of low surface potential utilizing the double finite Fourier transform method. Closed form expressions are also obtained for channels of large height to width ratio for which the depthwise variations vanish. Neglecting the Stern layer impact, the effects of EDL (Electric Double Layer) overlap, multiple ionic species, and association/dissociation reactions on the surface are all taken into account. Moreover, finite-element-based numerical simulations are conducted to account for the end effects as well as to validate the analytical solutions. We show that, with the exception of the migratory ionic conductivity, all the physicochemical parameters are strong functions of the channel aspect ratio. Accordingly, a slit geometry is not a good representative of a rectangular channel when the width is comparable to the height. It is also observed that the distribution of the electrical potential is not uniform over the surface of a charge-regulated channel. In addition, unlike ordinary channels for which an increase in the background salt concentration is always accompanied by higher flow rates, quite the opposite may be true for a pH-regulated duct at higher salt concentrations.

Observations of a bi-directional lightning leader producing an M-component

NASA Astrophysics Data System (ADS)

Kotovsky, D. A.; Uman, M. A.; Wilkes, R.; Carvalho, F. L.; Jordan, D. M.

2017-12-01

Lightning discharges to ground often exhibit millisecond-scale surges in the continuing currents following return strokes, called M-components. Relatively little is known regarding the source of M-component charge and the mechanisms by which that charge is transferred to ground. In this work, we seek to directly address these questions by presenting correlated high-speed video and Lightning Mapping Array (LMA) observations of a bi-directional leader that resulted in an M-component occurring in a rocket-and-wire triggered lightning flash. The observed leader initiated in the decayed remnants of a positive leader channel that had traversed virgin air approximately 90 msec prior. Three-dimensional locations and speeds of the photographed bi-directional leader and M-component processes are calculated by mapping video images to the observed LMA channel geometry. Both ends of the bi-directional leader exhibited speeds on the order of 2 x106 m sec-1 over 570 meters of the visible channel. Propagation of the luminosity wave from the in-cloud leader to ground ( 8.8 km channel length) exhibited appreciable dispersion, with rise-times (10-90%) increasing from 330 to 410 μsec and pulse-widths (half-maximum) increasing from 380 to 810 μsec - the M-component current pulse measured at ground-level exhibited a rise-time of 290 μsec and a pulse-width of 770 μsec. Group velocities of the luminosity wave have been calculated as a function of frequency, increasing from 2 x107 to 6 x107 m sec-1 over the dominant signal bandwidth (DC to 2 kHz). Additionally, multiple waves of luminosity are observed within the in-cloud channel, indicating nuanced wave phenomena possibly associated with reflection from the end of the leader channel and attachment with the main lightning channel carrying continuing current to ground.

Variability of electromagnetic signatures of lightning initiation observed in the West Mediterranean basin

NASA Astrophysics Data System (ADS)

Kolmasova, I.; Santolik, O.; Defer, E.; Stéphane, P.; Lan, R.; Uhlir, L.; Coquillat, S.; Lambert, D.; Pinty, J. P.; Prieur, S.

2016-12-01

Lightning discharges to ground often exhibit millisecond-scale surges in the continuing currents following return strokes, called M-components. Relatively little is known regarding the source of M-component charge and the mechanisms by which that charge is transferred to ground. In this work, we seek to directly address these questions by presenting correlated high-speed video and Lightning Mapping Array (LMA) observations of a bi-directional leader that resulted in an M-component occurring in a rocket-and-wire triggered lightning flash. The observed leader initiated in the decayed remnants of a positive leader channel that had traversed virgin air approximately 90 msec prior. Three-dimensional locations and speeds of the photographed bi-directional leader and M-component processes are calculated by mapping video images to the observed LMA channel geometry. Both ends of the bi-directional leader exhibited speeds on the order of 2 x106 m sec-1 over 570 meters of the visible channel. Propagation of the luminosity wave from the in-cloud leader to ground ( 8.8 km channel length) exhibited appreciable dispersion, with rise-times (10-90%) increasing from 330 to 410 μsec and pulse-widths (half-maximum) increasing from 380 to 810 μsec - the M-component current pulse measured at ground-level exhibited a rise-time of 290 μsec and a pulse-width of 770 μsec. Group velocities of the luminosity wave have been calculated as a function of frequency, increasing from 2 x107 to 6 x107 m sec-1 over the dominant signal bandwidth (DC to 2 kHz). Additionally, multiple waves of luminosity are observed within the in-cloud channel, indicating nuanced wave phenomena possibly associated with reflection from the end of the leader channel and attachment with the main lightning channel carrying continuing current to ground.

Characterization of radiometric calibration of LANDSAT-4 TM reflective bands

NASA Technical Reports Server (NTRS)

Barker, J. L.; Abrams, R. B.; Ball, D. L.; Leung, K. C.

1984-01-01

Prelaunch and postlaunch internal calibrator, image, and background data is to characterize the radiometric performance of the LANDSAT-4 TM and to recommend improved procedures for radiometric calibration. All but two channels (band 2, channel 4; band 5, channel 3) behave normally. Gain changes relative to a postlaunch reference for channels within a band vary within 0.5 percent as a group. Instrument gain for channels in the cold focal plane oscillates. Noise in background and image data ranges from 0.5 to 1.7 counts. Average differences in forward and reverse image data indicate a need for separate calibration processing of forward and reverse scans. Precision is improved by increasing the pulse integration width from 31 to 41 minor frames, depending on the band.

Hydrodynamic flow in capillary-channel fiber columns for liquid chromatography.

PubMed

Stanelle, Rayman D; Sander, Lane C; Marcus, R Kenneth

2005-12-23

The flow characteristics of capillary-channel polymer (C-CP) fiber liquid chromatographic (LC) columns have been investigated. The C-CP fibers are manufactured with eight longitudinal grooves (capillary channels) extending the length of the fibers. Three C-CP fiber examples were studied, with fiber dimensions ranging from approximately 35 microm to 65 microm, and capillary-channel dimensions ranging from approximately 6 microm to 35 microm. The influence of fiber packing density and column inner diameter on peak asymmetry, peak width, and run-to-run reproducibility have been studied for stainless steel LC columns packed with polyester (PET) and polypropylene (PP) C-CP fibers. The van Deemter A-term was evaluated as a function of fiber packing density (approximately 0.3 g/cm(3)-0.75 g/cm(3)) for columns of 4.6 mm inner diameter (i.d.) and at constant packing densities for 1.5 mm, 3.2 mm, 4.6 mm, and 7.7 mm i.d. columns. Although column diameter had little influence on the eluting peak widths, peak asymmetry increased with increasing column diameter. The A-terms for the C-CP fiber packed columns are somewhat larger than current commercial, microparticulate-packed columns, and means for improvement are discussed. Applications in the area of protein (macromolecule) separations appear the most promising at this stage of the system development.

Geomorphic and hydraulic assessment of the Bear River in and near Evanston, Wyoming

USGS Publications Warehouse

Smith, M.E.; Maderak, M.L.

1993-01-01

Geomorphic and hydraulic characteristics of the Bear River in and near Evanston, Wyoming, were assessed to assist planners in stabilizing the river channel. Present-day channel instability is the result of both human-made and natural factors. The primary factor is channelization of the river in Evanston, where several meander loops were cut off artificially during early development of the city. Other contributing factors include channel-width constrictions, bank stabilization, isolated bend cutoffs upstream from the city, and flooding in 1983 and 1984. A geomorphic analysis of bankfull-channel pattern, based on four aerial photographs taken during 1946-86, quantified geomorphic properties (reach sinuosity, bend sinuosity, bend radius of curvature, and bed length) that are characteristic of the study reach. The reach sinuosity of reach 2 (the channelized reach in Evanston) was 1.18 in 1986 and remained about the same throughout the period (1946-86). The reach sinuosity of reach 2 prior to channelization was substantially larger, about 2.3 as determined from maps prepared before 1946. Hydraulic analysis of the present-day channel (surveyed 1981-87) using a one-dimensional water-surface-profile computer model identified a bankfull discharge for the study reach of 3,600 cu ft/sec. A comparison of bankfull hydraulic properties for reaches 1, 2, and 3 indicated that the effects in reach 2 of channelization and channel-width constriction--increased slope, faster velocities, and greater hydraulic radii. The present-day channel slope in reach 2 is 0.00518 ft/ft, whereas a more stable slope would be between 0.00431 ft/ft (present-day slope in reach 1) and 0.00486 ft/ft (present-day slope in reach 3).

Emergent propagation modes of ferromagnetic swimmers in constrained geometries

NASA Astrophysics Data System (ADS)

Bryan, M. T.; Shelley, S. R.; Parish, M. J.; Petrov, P. G.; Winlove, C. P.; Gilbert, A. D.; Ogrin, F. Y.

2017-02-01

Magnetic microswimmers, composed of hard and soft ferromagnets connected by an elastic spring, are modelled under low Reynolds number conditions in the presence of geometrical boundaries. Approaching a surface, the magneto-elastic swimmer's velocity increases and its trajectory bends parallel to the surface contour. Further confinement to form a planar channel generates new propagation modes as the channel width narrows, altering the magneto-elastic swimmer's speed, orientation, and direction of travel. Our results demonstrate that constricted geometric environments, such as occuring in microfluidic channels or blood vessels, may influence the functionality of magneto-elastic microswimmers for applications such as drug delivery.

Downstream Variation of Bankfull Geometry for the Continental and Overseas Hydro-Eco-Regions of France.

NASA Astrophysics Data System (ADS)

Tamisier, V.; Gob, F.; Thommeret, N.; Bilodeau, C.; Raufaste, S.; Kreutzenberger, K.

2016-12-01

Bankfull channel geometry is a fundamental and widely used concept in hydrology, fluvial geomorphology, and ecosystem studies. We develop and compare downstream hydraulic geometry relationships for bankfull channel width (w) and depth (d) as a function of drainage area A, respectively w=aAb (DHGwA) and d=cAf (DHGdA), for the 12 of the 21 French Hydro-Eco-Regions which are defined in terms of climate, topography and geology. The models have been built from a database (CARHYCE) that includes 1500 river reaches for which a unique standardized field protocol was used. River reach morphology was described based on a survey of 15 cross-sections spaced at intervals of one bankfull width. Sediment size and riverine vegetation were also measured and characterized. This database covers a wide range of French river diversity in terms of geomorphic types and anthropogenic impacts. Sampled stream reaches range from 1 to 70 000 km² in drainage area, 1 to 320 m in bankfull width and 0.3 to 8.5 m in bankfull depth. Approximately 500 poorly disturbed reaches were identified from several indices of disturbance at reach and basin scale (large dams, urbanization, channelization, etc.). For these reference sites, drainage areas display strong power-law relationships with both the width and the depth in most Hydro-Eco-Regions, with coefficients of determination (R²) ranging from 0.73 to 0.91 for DHGwA and from 0.57 to 0.77 for DHGdA (p-value < 0.001, t-test). The DHG exponent b and f ranges from 0.36 to 0.5 for DHGwA and from 0.21 to 0.3 for DHGdA. This implies that widths increase more strongly than depths with increasing drainage areas. The relative position of the models are compared to the national model and discussed with regard to the geologic, climatic and topographic characteristics. In Hydro-Eco-Regions which exhibit poor DHG relationships, the role of spatial variability in natural controls (climate, topography and geology) is discussed. Finally, reaches identified as potentially disturbed by human activities are compared to the reference models.

Gate engineered heterostructure junctionless TFET with Gaussian doping profile for ambipolar suppression and electrical performance improvement

NASA Astrophysics Data System (ADS)

Aghandeh, Hadi; Sedigh Ziabari, Seyed Ali

2017-11-01

This study investigates a junctionless tunnel field-effect transistor with a dual material gate and a heterostructure channel/source interface (DMG-H-JLTFET). We find that using the heterostructure interface improves device behavior by reducing the tunneling barrier width at the channel/source interface. Simultaneously, the dual material gate structure decreases ambipolar current by increasing the tunneling barrier width at the drain/channel interface. The performance of the device is analyzed based on the energy band diagram at on, off, and ambipolar states. Numerical simulations demonstrate improvements in ION, IOFF, ION/IOFF, subthreshold slope (SS), transconductance and cut-off frequency and suppressed ambipolar behavior. Next, the workfunction optimization of dual material gate is studied. It is found that if appropriate workfunctions are selected for tunnel and auxiliary gates, the JLTFET exhibits considerably improved performance. We then study the influence of Gaussian doping distribution at the drain and the channel on the ambipolar performance of the device and find that a Gaussian doping profile and a dual material gate structure remarkably reduce ambipolar current. Gaussian doped DMG-H-JLTFET, also exhibits enhanced IOFF, ION/IOFF, SS and a low threshold voltage without degrading IOFF.

Effect of channel-width and chirality on graphene field-effect transistor based real-time biomolecule sensing

NASA Astrophysics Data System (ADS)

Lyu, Letian; Jaswal, Perveshwer; Xu, Guangyu

2018-03-01

Graphene field-effect transistors (GFET) hold promise in biomolecule sensing due to the outstanding properties of graphene materials. Charges in biomolecules are transduced into a change in the GFET current, which allows real-time monitoring of the biomolecule concentrations. Here we theoretically evaluate the performance of GFET based real-time biomolecule sensing, aiming to better understand the width-scaling limit in GFET based biosensors. In particular, we study the effect of the channel-width and the chirality on FET sensitivity by taking the percentage change of the FET current per unit charge density as the sensing signal. Firstly, GFETs made of graphene nanoribbons (GNR) and graphene sheets (GS) show comparable sensing signals to each other when gated at 1011 - 1012 cm-2 carrier densities. Sensing signals in GNRs are enhanced when gated near the sub-band thresholds, and increase their values in wider GNRs due to the change in device conductance and quantum capacitance. Secondly, the GNR chirality is found to fine tune the sensing signals. Armchair GNRs with smaller energy bandgaps appear to have an enhanced sensing signal close to 1011 cm-2 carrier densities. These results may help understand the scaling limit in GFET based biosensors along the width direction, and shed light on forming all-electrical bio-arrays.

Quality of terrestrial data derived from UAV photogrammetry: a case study of the Hetao irrigation district in northern China

NASA Astrophysics Data System (ADS)

Zhang, Hongming; Baartman, Jantiene E. M.; Yang, Xiaomei; Gai, Lingtong; Geissen, Violette

2017-04-01

Most crops in northern China are irrigated, but the topography affects water use, soil erosion, runoff and yields,. Technologies for collecting high-resolution topographic data are essential for adequately assessing these effects. Ground surveys and techniques of light detection and ranging have good accuracy, but data acquisition can be time-consuming and expensive for large catchments. Recent rapid technological development has provided new, flexible, high-resolution methods for collecting topographic data, such as photogrammetry using unmanned aerial vehicles (UAVs). The accuracy of UAV photogrammetry for generating high-resolution digital elevation models (DEMs) and for determining the width of irrigation channels, however, has not been assessed. We used a fixed-wing UAV for collecting high-resolution (0.15 m) topographic data for the Hetao irrigation district, the third largest irrigation district in China. We surveyed 112 ground checkpoints (GCPs) using a real-time kinematic global positioning system to evaluate the accuracy of the DEMs and channel widths. A comparison of manually measured channel widths with the widths derived from the DEMs indicated that the DEM-derived widths had vertical and horizontal root mean square errors of 13.0 and 7.9 cm, respectively. UAV photogrammetric data can thus be used for land surveying, digital mapping, calculating channel capacity, monitoring crops, and predicting yields, with the advantages of economy, speed, and ease.

Influence of the elastic deformation of a foam on its mobility in channels of linearly varying width.

PubMed

Dollet, Benjamin; Jones, Siân A; Méheust, Yves; Cantat, Isabelle

2014-08-01

We study foam flow in an elementary model porous medium consisting of a convergent and a divergent channel positioned side by side and possessing a fixed joint porosity. Configurations of converging or diverging channels are ubiquitous at the pore scale in porous media, as all channels linking pores possess a converging and diverging part. The resulting flow kinematics imposes asymmetric bubble deformations in the two channels, which modulate foam-wall friction and strongly impact the flux distribution. We measure, as well as quantitatively predict, the ratio of the fluxes in the two channels as a function of the channel widths by modeling pressure drops of both viscous and capillary origins. This study reveals the crucial importance of boundary-induced bubble deformation on the mobility of a flowing foam, resulting in particular in flow irreversibility.

Estimating discharge in rivers using remotely sensed hydraulic information

USGS Publications Warehouse

Bjerklie, D.M.; Moller, D.; Smith, L.C.; Dingman, S.L.

2005-01-01

A methodology to estimate in-bank river discharge exclusively from remotely sensed hydraulic data is developed. Water-surface width and maximum channel width measured from 26 aerial and digital orthophotos of 17 single channel rivers and 41 SAR images of three braided rivers were coupled with channel slope data obtained from topographic maps to estimate the discharge. The standard error of the discharge estimates were within a factor of 1.5-2 (50-100%) of the observed, with the mean estimate accuracy within 10%. This level of accuracy was achieved using calibration functions developed from observed discharge. The calibration functions use reach specific geomorphic variables, the maximum channel width and the channel slope, to predict a correction factor. The calibration functions are related to channel type. Surface velocity and width information, obtained from a single C-band image obtained by the Jet Propulsion Laboratory's (JPL's) AirSAR was also used to estimate discharge for a reach of the Missouri River. Without using a calibration function, the estimate accuracy was +72% of the observed discharge, which is within the expected range of uncertainty for the method. However, using the observed velocity to calibrate the initial estimate improved the estimate accuracy to within +10% of the observed. Remotely sensed discharge estimates with accuracies reported in this paper could be useful for regional or continental scale hydrologic studies, or in regions where ground-based data is lacking. ?? 2004 Elsevier B.V. All rights reserved.

Enhancement of Electrokinetically-Driven Flow Mixing in Microchannel with Added Side Channels

NASA Astrophysics Data System (ADS)

Yang, Ruey-Jen; Wu, Chien-Hsien; Tseng, Tzu-I; Huang, Sung-Bin; Lee, Gwo-Bin

2005-10-01

Electroosmotic flow (EOF) in microchannels is restricted to low Reynolds number regimes. Since the inertial forces are extremely weak in such regimes, turbulent conditions do not readily develop. Therefore, species mixing occurs primarily via diffusion, with the result that extended mixing channels are generally required. The present study considers a T-shaped microchannel configuration with a mixing channel of width W=280 μm. Computational fluid dynamics simulations and experiments were performed to investigate the influence on the mixing efficiency of various geometrical parameters, including the side-channel width, the side-channel separation, and the number of side-channel pairs. The influence of different applied voltages is also considered. The numerical results reveal that the mixing efficiency can be enhanced to yield a fourfold improvement by incorporating two pairs of side channels into the mixing channel. It was also found that the mixing performance depends significantly upon the magnitudes of the applied voltages.

Biomolecule detection based on Si single-electron transistors for practical use

NASA Astrophysics Data System (ADS)

Nakajima, Anri; Kudo, Takashi; Furuse, Sadaharu

2013-07-01

Experimental and theoretical analyses demonstrated that ultra-sensitive biomolecule detection can be achieved using a Si single-electron transistor (SET). A multi-island channel structure was used to enable room-temperature operation. Coulomb oscillation increases transconductance without increasing channel width, which increases detection sensitivity to a charged target. A biotin-modified SET biosensor was used to detect streptavidin at a dilute concentration. In addition, an antibody-functionalized SET biosensor was used for immunodetection of prostate-specific antigen, demonstrating its suitability for practical use. The feasibility of ultra-sensitive detection of biomolecules for practical use by using a SET biosensor was clearly proven through this systematic study.

Influence of bedrock on river hydrodynamics and channel geometry

NASA Astrophysics Data System (ADS)

Rennie, C. D.; Church, M. A.; Venditti, J. G.; Bomhof, J.; Adderley, C.

2013-12-01

We present an acoustic Doppler current profiler (aDcp) survey of a 524 km long reach of Fraser River, British Columbia, Canada, as it passes through the Fraser Canyons. The channel alternates between gravel-bedded reaches that are incised into semi-consolidated glacial deposits and bedrock-bound reaches (7.7% of the reach between the towns of Quesnel and Hope). A continuous centreline aDcp survey was employed to measure longitudinal variation in slope, depth, depth-averaged velocity, and shear velocity. A total of 71 aDcp sectional surveys throughout the reach provided section widths (w), section-averaged depths (d), velocity distributions, and discharge (Q). Finally, air photo analysis using Google imagery provided channel widths at 0.5 km spacing. The survey reach was subdivided into 10 morphological sub-reaches, which ranged from alluvial gravel-bed reaches with relatively moderate slope to steep non-alluvial rock-walled canyons. The resulting data provide a unique opportunity to evaluate the influence of bedrock confinement on river hydrodynamics and channel geometry. Continuous centreline longitudinal aDcp data and the widths from air photo analysis were grouped within each sub-reach based on presence of bedrock confinement on both banks, either bank, or neither bank. The results demonstrate that river widths decreased and water depths, flow velocities, and shear velocities increased from the alluvial sub-reaches to the semi-alluvial reaches to the canyon reaches. Within each sub-reach, locations with bedrock encroachment on both banks were also narrower and deeper, but had lower depth-averaged velocity and shear velocity. Sectional geometry data were homogenized along the river (to compensate increasing flows at tributary junctions) by computing w/Q^{1/2} and d/Q^{1/3}, following commonly observed scaling relations. Alluvial reaches are 2.3x wider than rock-bound reaches (from the more abundant imagery data) and 0.60x as deep (from aDcp sections), implying that mean velocity is accelerated in rock reaches by 38%. There is also variation from reach to reach along the river controlled by variation in rock lithologies, with the narrowest canyons occurring in Fraser Canyon proper (w/Q^{1/2} = 0.083 compared with 1.4 elsewhere). The uppermost (';Marguerite') and lowermost (';Agassiz') alluvial reaches are considerably wider (w/Q^{1/2}= 3.9 and 7.1 respectively) than intervening ones ( 2.35). These reaches have lower gradients and exhibit wandering channels. Because of lithological control, the downstream hydraulic geometry of the river does not, in fact, conform with the common pattern, even when sections are analyzed according to boundary material. However, river gradient is well correlated with scaled width; inversely for gravel reaches and directly, but with little sensitivity, for rock-bound reaches.

Spectroscopic requirements for HALOE: An analysis of the HCl and HF channels

NASA Technical Reports Server (NTRS)

Rinsland, C. P.; Smith, M. A. H.; Park, J. H.; Harvey, G. A.; Russell, J. M., III; Richardson, D. J.

1982-01-01

Spectral line parameters that have absorption features within the HCl and HF channels of the Halogen Occultation Experiment (HALOE) were evaluated. Line positions and identification of stratospheric and solar absorption features in both channels are presented based on an analysis of high-resolution, balloon-borne solar occultation spectra. For the relevant HCl and HF lines and for transitions of the interfering species, the accuracy of the following spectral parameters was assessed: line positions, line strengths, lower state energies, air-broadened collisional half-widths, and temperature dependence of the air-broadened half-widths. In addition, since the HALOE instrument and calibration cells are filled with mixtures of HCl in N2 and HF in N2, the self-broadened and N2-broadened HF and HCl half-widths were also considered.

Predicting changes in hydrologic retention in an evolving semi-arid alluvial stream

USGS Publications Warehouse

Harvey, J.W.; Conklin, M.H.; Koelsch, R.S.

2003-01-01

Hydrologic retention of solutes in hyporheic zones or other slowly moving waters of natural channels is thought to be a significant control on biogeochemical cycling and ecology of streams. To learn more about factors affecting hydrologic retention, we repeated stream-tracer injections for 5 years in a semi-arid alluvial stream (Pinal Creek, Ariz.) during a period when streamflow was decreasing, channel width increasing, and coverage of aquatic macrophytes expanding. Average stream velocity at Pinal Creek decreased from 0.8 to 0.2 m/s, average stream depth decreased from 0.09 to 0.04 m, and average channel width expanded from 3 to 13 m. Modeling of tracer experiments indicated that the hydrologic retention factor (Rh), a measure of the average time that solute spends in storage per unit length of downstream transport, increased from 0.02 to 8 s/m. At the same time the ratio of cross-sectional area of storage zones to main channel cross-sectional area (As/A) increased from 0.2 to 0.8 m2/m2, and average water residence time in storage zones (ts) increased from 5 to 24 min. Compared with published data from four other streams in the US, Pinal Creek experienced the greatest change in hydrologic retention for a given change in streamflow. The other streams differed from Pinal Creek in that they experienced a change in streamflow between tracer experiments without substantial geomorphic or vegetative adjustments. As a result, a regression of hydrologic retention on streamflow developed for the other streams underpredicted the measured increases in hydrologic retention at Pinal Creek. The increase in hydrologic retention at Pinal Creek was more accurately predicted when measurements of the Darcy-Weisbach friction factor were used (either alone or in addition to streamflow) as a predictor variable. We conclude that relatively simple measurements of channel friction are useful for predicting the response of hydrologic retention in streams to major adjustments in channel morphology as well as changes in streamflow. Published by Elsevier Ltd.

Electroosmotic flow in a rectangular channel with variable wall zeta-potential: comparison of numerical simulation with asymptotic theory.

PubMed

Datta, Subhra; Ghosal, Sandip; Patankar, Neelesh A

2006-02-01

Electroosmotic flow in a straight micro-channel of rectangular cross-section is computed numerically for several situations where the wall zeta-potential is not constant but has a specified spatial variation. The results of the computation are compared with an earlier published asymptotic theory based on the lubrication approximation: the assumption that any axial variations take place on a long length scale compared to a characteristic channel width. The computational results are found to be in excellent agreement with the theory even when the scale of axial variations is comparable to the channel width. In the opposite limit when the wavelength of fluctuations is much shorter than the channel width, the lubrication theory fails to describe the solution either qualitatively or quantitatively. In this short wave limit the solution is well described by Ajdari's theory for electroosmotic flow between infinite parallel plates (Ajdari, A., Phys. Rev. E 1996, 53, 4996-5005.) The infinitely thin electric double layer limit is assumed in the theory as well as in the simulation.

Sensitivity of tidal characteristics in double inlet systems to momentum dissipation on tidal flats: a perturbation analysis

NASA Astrophysics Data System (ADS)

Hepkema, Tjebbe M.; de Swart, Huib E.; Zagaris, Antonios; Duran–Matute, Matias

2018-05-01

In a tidal channel with adjacent tidal flats, along-channel momentum is dissipated on the flats during rising tides. This leads to a sink of along-channel momentum. Using a perturbative method, it is shown that the momentum sink slightly reduces the M2 amplitude of both the sea surface elevation and current velocity and favours flood dominant tides. These changes in tidal characteristics (phase and amplitude of sea surface elevations and currents) are noticeable if widths of tidal flats are at least of the same order as the channel width, and amplitudes and gradients of along-channel velocity are large. The M2 amplitudes are reduced because stagnant water flows from the flats into the channel, thereby slowing down the current. The M4 amplitudes and phases change because the momentum sink acts as an advective term during the fall of the tide, such a term generates flood dominant currents. For a prototype embayment that resembles the Marsdiep-Vlie double-inlet system of the Western Wadden Sea, it is found that for both the sea surface elevation and current velocity, including the momentum sink, lead to a decrease of approximately 2 % in M2 amplitudes and an increase of approximately 25 % in M4 amplitudes. As a result, the net import of coarse sediment is increased by approximately 35 %, while the transport of fine sediment is hardly influenced by the momentum sink. For the Marsdiep-Vlie system, the M2 sea surface amplitude obtained from the idealised model is similar to that computed with a realistic three-dimensional numerical model whilst the comparison with regard to M4 improves if momentum sink is accounted for.

Propagation of a finite bubble in a Hele-Shaw channel of variable depth

NASA Astrophysics Data System (ADS)

Juel, Anne; Franco-Gomez, Andres; Thompson, Alice; Hazel, Andrew

2017-11-01

We study the propagation of finite bubbles in a Hele-Shaw channel, where a centred rail is introduced to provide a small axially-uniform depth constriction. We demonstrate experimentally that this channel geometry can be used as a passive sorting device. Single air bubbles carried within silicone oil are generally transported on one side of the rail. However, for flow rates marginally larger than a critical value, a narrow band of bubble sizes on the order of the rail width can propagate over the rail, while bubbles of other sizes segregate to the side of the rail. The width of this band of bubble sizes increases with flow rate and the size of the most stable bubble can be tuned by varying the rail width. We present a depth-averaged theory which reveals that the mechanism relies on a non-trivial interaction between capillary and viscous forces that is fully dynamic, rather than being a simple modification of capillary static solutions. In contrast, for larger bubbles and sufficiently large imposed flow rates, we find that initially centred bubbles do not converge onto a steady mode of propagation. Instead they transiently explore weakly unstable steady modes, an evolution which results in their break-up and eventual settling into a steady state of changed topology. The financial support of CONICYT and the Leverhulme Trust are gratefully acknowledged.

Self-organization of linear nanochannel networks

NASA Astrophysics Data System (ADS)

Annabattula, R. K.; Veenstra, J. M.; Mei, Y. F.; Schmidt, O. G.; Onck, P. R.

2010-06-01

A theoretical study has been conducted to explore the mechanics of self-organizing channel networks with dimensions in the submicron range and nanorange. The channels form by the partial release and bond back of prestressed thin films. In the release phase, the film spontaneously buckles into wrinkles of a certain wavelength, followed by a bond-back phase in which the final channel geometry is established through cohesive interface attractions. Results are presented in terms of the channel spacing, height, and width as a function of the film stiffness, thickness, eigenstrain, etch width, and interface energy. We have identified two dimensionless parameters that fully quantify the network assembly, showing excellent agreement with experiments. Our results provide valuable insight for the design of submicron and nanoscale channel networks with specific geometries.

Real-Time Noise Reduction for Mossbauer Spectroscopy through Online Implementation of a Modified Kalman Filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abrecht, David G.; Schwantes, Jon M.; Kukkadapu, Ravi K.

2015-02-01

Spectrum-processing software that incorporates a gaussian smoothing kernel within the statistics of first-order Kalman filtration has been developed to provide cross-channel spectral noise reduction for increased real-time signal-to-noise ratios for Mossbauer spectroscopy. The filter was optimized for the breadth of the gaussian using the Mossbauer spectrum of natural iron foil, and comparisons between the peak broadening, signal-to-noise ratios, and shifts in the calculated hyperfine parameters are presented. The results of optimization give a maximum improvement in the signal-to-noise ratio of 51.1% over the unfiltered spectrum at a gaussian breadth of 27 channels, or 2.5% of the total spectrum width. Themore » full-width half-maximum of the spectrum peaks showed an increase of 19.6% at this optimum point, indicating a relatively weak increase in the peak broadening relative to the signal enhancement, leading to an overall increase in the observable signal. Calculations of the hyperfine parameters showed no statistically significant deviations were introduced from the application of the filter, confirming the utility of this filter for spectroscopy applications.« less

Influence of an anomalous dimension effect on thermal instability in amorphous-InGaZnO thin-film transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Kuan-Hsien; Chou, Wu-Ching, E-mail: tcchang3708@gmail.com, E-mail: wuchingchou@mail.nctu.edu.tw; Chang, Ting-Chang, E-mail: tcchang3708@gmail.com, E-mail: wuchingchou@mail.nctu.edu.tw

2014-10-21

This paper investigates abnormal dimension-dependent thermal instability in amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors. Device dimension should theoretically have no effects on threshold voltage, except for in short channel devices. Unlike short channel drain-induced source barrier lowering effect, threshold voltage increases with increasing drain voltage. Furthermore, for devices with either a relatively large channel width or a short channel length, the output drain current decreases instead of saturating with an increase in drain voltage. Moreover, the wider the channel and the shorter the channel length, the larger the threshold voltage and output on-state current degradation that is observed. Because of themore » surrounding oxide and other thermal insulating material and the low thermal conductivity of the IGZO layer, the self-heating effect will be pronounced in wider/shorter channel length devices and those with a larger operating drain bias. To further clarify the physical mechanism, fast I{sub D}-V{sub G} and modulated peak/base pulse time I{sub D}-V{sub D} measurements are utilized to demonstrate the self-heating induced anomalous dimension-dependent threshold voltage variation and on-state current degradation.« less

Instream wood in a steep headwater channel: geomorphic significance of large and small wood

NASA Astrophysics Data System (ADS)

Galia, Tomáš; Šilhán, Karel; Ruiz-Villanueva, Virginia; Tichavský, Radek

2016-04-01

Besides the well-known significance of large wood (LW), also small woody pieces (SW; here defined as pieces with dimensions at least 0.5 m length and 0.05 m diameter), can play an important role in steep narrow headwaters. We inventoried instream wood in the 0.4 km long Mazák headwater channel, Moravskoslezské Beskydy Mts, Czech Republic (2

Channel response to increased and decreased bedload supply from land use change: contrasts between two catchments

NASA Astrophysics Data System (ADS)

Kondolf, G. M.; Piégay, H.; Landon, N.

2002-06-01

The catchments of Pine Creek, Idaho, USA (200 km 2), and the Drôme River in the Drôme Department, France (1640 km 2), illustrate contrasting changes in land use, bedload sediment production, and channel response. Hard-rock mining began in the catchment of Pine Creek near the end of the 19th century and, together with road construction, timber harvest, and historically heavy grazing of uplands, resulted in increased tributary bedload yield. Increased bedload migrating to the channel, combined with removal of large cedar trees on the floodplain, resulted in channel instability, which propagated downstream over a period of decades. On many reaches of Pine Creek, active channel width has increased by over 50% since 1933. Over roughly the same time period, the Drôme River catchment was extensively reforested (after at least one century of denudation and heavy grazing) and numerous check dams were constructed on torrents to reduce erosion. As a result, the Drôme River has experienced a reduction in bedload sediment supply since the late 19th century. In addition, gravel has been extracted from some reaches. Consequently, the channel has degraded and gravel bars have been colonized with woody riparian vegetation. Channel widths in wide, braided reaches decreased from 1947 to 1970 by 60%. On Pine Creek, channel instability has resulted in bank erosion (exposing contaminated mine tailings) and increased flood hazard. On the Drôme River, degradation has undermined bridges and embankments, and lowered the water table in areas dependent on groundwater for irrigation, resulting in loss of 6 million m 3 of groundwater storage since 1960. Though they differ in drainage area by nearly an order of magnitude, Pine Creek and the Drôme River provide an excellent contrast in that they represent two sides of an epicycle of alluvial sedimentation set off in each case by land disturbance. In both cases, the most recent channel changes, though in opposite directions, were viewed as negative by river managers. On Pine Creek, managers have removed (or protected from erosion) mine tailings, and have attempted to train the stream into a more stable channel, and most rock waste piles (the principal sediment sources) have recently been controlled. On the Drôme River, managers have prohibited gravel mining and adopted new policies to permit coarse sediment to migrate through the river system.

Geomorphic effects, flood power, and channel competence of a catastrophic flood in confined and unconfined reaches of the upper Lockyer valley, southeast Queensland, Australia

NASA Astrophysics Data System (ADS)

Thompson, Chris; Croke, Jacky

2013-09-01

Flooding is a persistent natural hazard, and even modest changes in future climate are believed to lead to large increases in flood magnitude. Previous studies of extreme floods have reported a range of geomorphic responses from negligible change to catastrophic channel change. This paper provides an assessment of the geomorphic effects of a rare, high magnitude event that occurred in the Lockyer valley, southeast Queensland in January 2011. The average return interval of the resulting flood was ~ 2000 years in the upper catchment and decreased to ~ 30 years downstream. A multitemporal LiDAR-derived DEM of Difference (DoD) is used to quantify morphological change in two study reaches with contrasting valley settings (confined and unconfined). Differences in geomorphic response between reaches are examined in the context of changes in flood power, channel competence and degree of valley confinement using a combination of one-dimensional (1-D) and two-dimensional (2-D) hydraulic modelling. Flood power peaked at 9800 W m- 2 along the confined reach and was 2-3 times lower along the unconfined reach. Results from the DoD confirm that the confined reach was net erosional, exporting ~ 287,000 m3 of sediment whilst the unconfined reach was net depositional gaining ~ 209,000 m3 of sediment, 70% of the amount exported from the upstream, confined reach. The major sources of eroded sediment in the confined reach were within channel benches and macrochannel banks resulting in a significant increase of channel width. In the unconfined reach, the benches and floodplains were the major loci for deposition, whilst the inner channel exhibited minor width increases. The presence of high stream power values, and resultant high erosion rates, within the confined reach is a function of the higher energy gradient of the steeper channel that is associated with knickpoint development. Dramatic differences in geomorphic responses were observed between the two adjacent reaches of contrasting valley configuration. The confined reach experienced large-scale erosion and reorganisation of the channel morphology that resulted in significantly different areal representations of the five geomorphic features classified in this study.

Geomorphic effects of rural-to-urban land use conversion on three streams in the Central Redbed Plains of Oklahoma

NASA Astrophysics Data System (ADS)

Kang, Ranbir S.; Marston, Richard A.

2006-09-01

This research evaluates the impact of rural-to-urban land use conversion on channel morphology and riparian vegetation for three streams in the Central Redbed Plains geomorphic province (central Great Plains ecoregion) of Oklahoma. The Deep Fork Creek watershed is largely urbanized; the Skeleton Creek watershed is largely rural; and the Stillwater Creek watershed is experiencing a rapid transition from rural to urban land cover. Each channel was divided into reaches based on tributary junctions, sinuosity, and slope. Field surveys were conducted at transects in a total of 90 reaches, including measurements of channel units, channel cross-section at bankfull stage, and riparian vegetation. Historical aerial photographs were available for only Stillwater Creek watershed, which were used to document land cover in this watershed, especially changes in the extent of urban areas (impervious cover). The three streams have very low gradients (< 0.001), width-to-depth ratios < 10, and cohesive channel banks, but have incised into red Permian shales and sandstone. The riparian vegetation is dominated by cottonwoods, ash, and elm trees that provide a dense root mat on stream banks where the riparian vegetation is intact. Channels increased in width and depth in the downstream direction as is normally expected, but the substrate materials and channel units remained unchanged. Statistical analyses demonstrated that urbanization did not explain spatial patterns of changes in any variables. These three channels in the central Redbed Plains are responding as flumes during peak flows, funneling runoff and the wash-load sediment downstream in major runoff events without any effect on channel dimensions. Therefore, local geological conditions (similar bedrock, cohesive substrates and similar riparian vegetation) are mitigating the effects of urbanization.

Can stream and riparian restoration offset climate change impacts to salmon populations?

PubMed

Justice, Casey; White, Seth M; McCullough, Dale A; Graves, David S; Blanchard, Monica R

2017-03-01

Understanding how stream temperature responds to restoration of riparian vegetation and channel morphology in context of future climate change is critical for prioritizing restoration actions and recovering imperiled salmon populations. We used a deterministic water temperature model to investigate potential thermal benefits of riparian reforestation and channel narrowing to Chinook Salmon populations in the Upper Grande Ronde River and Catherine Creek basins in Northeast Oregon, USA. A legacy of intensive land use practices in these basins has significantly reduced streamside vegetation and increased channel width across most of the stream network, resulting in water temperatures that far exceed the optimal range for salmon growth and survival. By combining restoration scenarios with climate change projections, we were able to evaluate whether future climate impacts could be offset by restoration actions. A combination of riparian restoration and channel narrowing was predicted to reduce peak summer water temperatures by 6.5 °C on average in the Upper Grande Ronde River and 3.0 °C in Catherine Creek in the absence of other perturbations. These results translated to increases in Chinook Salmon parr abundance of 590% and 67% respectively. Although projected climate change impacts on water temperature for the 2080s time period were substantial (i.e., median increase of 2.7 °C in the Upper Grande Ronde and 1.5 °C in Catherine Creek), we predicted that basin-wide restoration of riparian vegetation and channel width could offset these impacts, reducing peak summer water temperatures by about 3.5 °C in the Upper Grande Ronde and 1.8 °C in Catherine Creek. These results underscore the potential for riparian and stream channel restoration to mitigate climate change impacts to threatened salmon populations in the Pacific Northwest. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Pressure-driven flow of a Herschel-Bulkley fluid with pressure-dependent rheological parameters

NASA Astrophysics Data System (ADS)

Panaseti, Pandelitsa; Damianou, Yiolanda; Georgiou, Georgios C.; Housiadas, Kostas D.

2018-03-01

The lubrication flow of a Herschel-Bulkley fluid in a symmetric long channel of varying width, 2h(x), is modeled extending the approach proposed by Fusi et al. ["Pressure-driven lubrication flow of a Bingham fluid in a channel: A novel approach," J. Non-Newtonian Fluid Mech. 221, 66-75 (2015)] for a Bingham plastic. Moreover, both the consistency index and the yield stress are assumed to be pressure-dependent. Under the lubrication approximation, the pressure at zero order depends only on x and the semi-width of the unyielded core is found to be given by σ(x) = -(1 + 1/n)h(x) + C, where n is the power-law exponent and the constant C depends on the Bingham number and the consistency-index and yield-stress growth numbers. Hence, in a channel of constant width, the width of the unyielded core is also constant, despite the pressure dependence of the yield stress, and the pressure distribution is not affected by the yield-stress function. With the present model, the pressure is calculated numerically solving an integro-differential equation and then the position of the yield surface and the two velocity components are computed using analytical expressions. Some analytical solutions are also derived for channels of constant and linearly varying widths. The lubrication solutions for other geometries are calculated numerically. The implications of the pressure-dependence of the material parameters and the limitations of the method are discussed.

Performance Prediction of Darrieus-Type Hydroturbine with Inlet Nozzle Operated in Open Water Channels

NASA Astrophysics Data System (ADS)

Nakashima, K.; Watanabe, S.; Matsushita, D.; Tsuda, S.; Furukawa, A.

2016-11-01

Small hydropower is one of the renewable energies and is expected to be effectively used for local supply of electricity. We have developed Darrieus-type hydro-turbine systems, and among them, the Darrieus-turbine with a weir and a nozzle installed upstream of turbine is, so far, in success to obtain more output power by gathering all water into the turbine. However, there can several cases exist, in which installing the weir covering all the flow channel width is unrealistic, and in such cases, the turbine should be put alone in open channels without upstream weir. Since the output power is very small in such a utilization of small hydropower, it is important to derive more power for the cost reduction. In the present study, we parametrically investigate the preferable shape of the inlet nozzle for the Darrieus-type hydroturbine operated in an open flow channel. Experimental investigation is carried out in the open channel in our lab. Tested inlet nozzles are composed of two flat plates with the various nozzle converging angles and nozzle outlet (runner inlet) widths with the nozzle inlet width kept constant. As a result, the turbine with the nozzles having large converging angle and wide outlet width generates higher power. Two-dimensional unsteady numerical simulation is also carried out to qualitatively understand the flow mechanism leading to the better performance of turbine. Since the depth, the width and the flow rate in the real open flow channels are different from place to place and, in some cases from time to time, it is also important to predict the onsite performance of the hydroturbine from the lab experiment at planning stage. One-dimensional stream-tube model is developed for this purpose, in which the Darrieus-type hydroturbine with the inlet nozzle is considered as an actuator-disk modelled based on our experimental and numerical results.

Effects of magnetic field strength in the discharge channel on the performance of a multi-cusped field thruster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Peng; Liu, Hui; Gao, Yuanyuan

The performance characteristics of a Multi-cusped Field Thruster depending on the magnetic field strength in the discharge channel were investigated. Four thrusters with different outer diameters of the magnet rings were designed to change the magnetic field strength in the discharge channel. It is found that increasing the magnetic field strength could restrain the radial cross-field electron current and decrease the radial width of main ionization region, which gives rise to the reduction of propellant utilization and thruster performance. The test results in different anode voltage conditions indicate that both the thrust and anode efficiency are higher for the weakermore » magnetic field in the discharge channel.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Hyun-Sik; Jeon, Sanghun, E-mail: jeonsh@korea.ac.kr

Upon light exposure, an indium-zinc-oxide (IZO) thin-film transistor (TFT) presents higher photoconductivity by several orders of magnitude at the negative gate bias region. Among various device geometrical factors, scaling down the channel length of the photo-transistor results in an anomalous increase in photoconductivity. To probe the origin of this high photoconductivity in short-channel device, we measured transient current, current–voltage, and capacitance–voltage characteristics of IZO–TFTs with various channel lengths and widths before and after illumination. Under the illumination, the equilibrium potential region which lies far from front interface exists only in short-channel devices, forming the un-depleted conducting back channel. This regionmore » plays an important role in carrier transport under the illumination, leading to high photoconductivity in short-channel devices. Photon exposure coupled with gate-modulated band bending for short-channel devices leads to the accumulation of V{sub o}{sup ++} at the front channel and screening negative gate bias, thereby generating high current flow in the un-depleted back-channel region.« less

Compact pulse width modulation circuitry for silicon photomultiplier readout.

PubMed

Bieniosek, M F; Olcott, P D; Levin, C S

2013-08-07

The adoption of solid-state photodetectors for positron emission tomography (PET) system design and the interest in 3D interaction information from PET detectors has lead to an increasing number of readout channels in PET systems. To handle these additional readout channels, PET readout electronics should be simplified to reduce the power consumption, cost, and size of the electronics for a single channel. Pulse-width modulation (PWM), where detector pulses are converted to digital pulses with width proportional to the detected photon energy, promises to simplify PET readout by converting the signals to digital form at the beginning of the processing chain, and allowing a single time-to-digital converter to perform the data acquisition for many channels rather than routing many analogue channels and digitizing in the back end. Integrator based PWM systems, also known as charge-to-time converters (QTCs), are especially compact, reducing the front-end electronics to an op-amp integrator with a resistor discharge, and a comparator. QTCs, however, have a long dead-time during which dark count noise is integrated, reducing the output signal-to-noise ratio. This work presents a QTC based PWM circuit with a gated integrator that shows performance improvements over existing QTC based PWM. By opening and closing an analogue switch on the input of the integrator, the circuit can be controlled to integrate only the portions of the signal with a high signal-to-noise ratio. It also allows for multiplexing different detectors into the same PWM circuit while avoiding uncorrelated noise propagation between photodetector channels. Four gated integrator PWM circuits were built to readout the spatial channels of two position sensitive solid-state photomultiplier (PS-SSPM). Results show a 4 × 4 array 0.9 mm × 0.9 mm × 15 mm of LYSO crystals being identified on the 5 mm × 5 mm PS-SSPM at room temperature with no degradation for twofold multiplexing. In principle, much larger multiplexing ratios are possible, limited only by count rate issues.

The effect of channel shape, bed morphology, and shipwrecks on flow velocities in the Upper St. Clair River

USGS Publications Warehouse

Czuba, Jonathan A.; Oberg, Kevin; Best, Jim; Parsons, Daniel R.

2009-01-01

In the Great Lakes of North America, the St. Clair River is the major outlet of Lake Huron and conveys water to Lake St. Clair which then flows to Lake Erie. One major topic of interest is morphological change in the St. Clair River and its impact on water levels in the Upper Great Lakes and connecting channel flows. A combined multibeam echosounder (MBES) bathymetric survey and acoustic Doppler current profiler (ADCP) flow survey of the outlet of Lake Huron and the Upper St. Clair River was conducted July 21 – 25, 2008. This paper presents how channel morphology and shipwrecks affect the flow in the Upper St. Clair River. The river is most constricted at the Blue Water Bridge near Port Huron, Michigan, with water velocities over 2 ms-1 for a flow of 5,200 m3s-1. Downstream of this constriction, the river flows around a bend and expands creating a large recirculation zone along the left bank due to flow separation. This recirculation zone reduces the effective channel width, and thus increases flow velocities to over 2 ms-1 in this region. The surveys reveal several shipwrecks on the bed of the St. Clair River, which possess distinct wakes in their flow velocity downstream of the wrecks. The constriction and expansion of the channel, combined with forcing of the flow by bed topography, initiates channel-scale secondary flow, creating streamwise vortices that maintain coherence downstream over a distance of several channel widths.

Effects of wall suction/blowing on two-dimensional flow past a confined square cylinder.

PubMed

Zhang, Wei; Jiang, Yanqun; Li, Lang; Chen, Guoping

2016-01-01

A numerical simulation is conducted to study the laminar flow past a square cylinder confined in a channel (the ratio of side length of the square to channel width is fixed at 1/4) subjected to a locally uniform blowing/suction speed placed at the top and bottom channel walls. Governing equations with boundary conditions are resolved using a finite volume method in pressure-velocity formulation. The flow patterns relevant to the critical spacing values are investigated. Numerical results show that wall blowing has a stabilizing effect on the flow, and the corresponding critical Reynolds number increases monotonically with increasing blowing velocity. Remarkably, steady asymmetric solutions and hysteretic mode transitions exist in a certain range of parameters (Reynolds number and suction speed) in the case of suction.

Characterization of the spatial variability of channel morphology

USGS Publications Warehouse

Moody, J.A.; Troutman, B.M.

2002-01-01

The spatial variability of two fundamental morphological variables is investigated for rivers having a wide range of discharge (five orders of magnitude). The variables, water-surface width and average depth, were measured at 58 to 888 equally spaced cross-sections in channel links (river reaches between major tributaries). These measurements provide data to characterize the two-dimensional structure of a channel link which is the fundamental unit of a channel network. The morphological variables have nearly log-normal probability distributions. A general relation was determined which relates the means of the log-transformed variables to the logarithm of discharge similar to previously published downstream hydraulic geometry relations. The spatial variability of the variables is described by two properties: (1) the coefficient of variation which was nearly constant (0.13-0.42) over a wide range of discharge; and (2) the integral length scale in the downstream direction which was approximately equal to one to two mean channel widths. The joint probability distribution of the morphological variables in the downstream direction was modelled as a first-order, bivariate autoregressive process. This model accounted for up to 76 per cent of the total variance. The two-dimensional morphological variables can be scaled such that the channel width-depth process is independent of discharge. The scaling properties will be valuable to modellers of both basin and channel dynamics. Published in 2002 John Wiley and Sons, Ltd.

Generalized Reich-Moore R-matrix approximation

NASA Astrophysics Data System (ADS)

Arbanas, Goran; Sobes, Vladimir; Holcomb, Andrew; Ducru, Pablo; Pigni, Marco; Wiarda, Dorothea

2017-09-01

A conventional Reich-Moore approximation (RMA) of R-matrix is generalized into a manifestly unitary form by introducing a set of resonant capture channels treated explicitly in a generalized, reduced R-matrix. A dramatic reduction of channel space witnessed in conventional RMA, from Nc × Nc full R-matrix to Np × Np reduced R-matrix, where Nc = Np + Nγ, Np and Nγ denoting the number of particle and γ-ray channels, respectively, is due to Np < Nγ. A corresponding reduction of channel space in generalized RMA (GRMA) is from Nc × Nc full R-matrix to N × N, where N = Np + N, and where N is the number of capture channels defined in GRMA. We show that N = Nλ where Nλ is the number of R-matrix levels. This reduction in channel space, although not as dramatic as in the conventional RMA, could be significant for medium and heavy nuclides where N < Nγ. The resonant capture channels defined by GRMA accommodate level-level interference (via capture channels) neglected in conventional RMA. The expression for total capture cross section in GRMA is formally equal to that of the full Nc × NcR-matrix. This suggests that GRMA could yield improved nuclear data evaluations in the resolved resonance range at a cost of introducing N(N - 1)/2 resonant capture width parameters relative to conventional RMA. Manifest unitarity of GRMA justifies a method advocated by Fröhner and implemented in the SAMMY nuclear data evaluation code for enforcing unitarity of conventional RMA. Capture widths of GRMA are exactly convertible into alternative R-matrix parameters via Brune tranform. Application of idealized statistical methods to GRMA shows that variance among conventional RMA capture widths in extant RMA evaluations could be used to estimate variance among off-diagonal elements neglected by conventional RMA. Significant departure of capture widths from an idealized distribution may indicate the presence of underlying doorway states.

Ultracompact beam splitters based on plasmonic nanoslits

PubMed Central

Zhou, Chuanhong; Kohli, Punit

2011-01-01

An ultracompact plasmonic beam splitter is theoretically and numerically investigated. The splitter consists of a V-shaped nanoslit in metal films. Two groups of nanoscale metallic grooves inside the slit (A) and at the small slit opening (B) are investigated. We show that there are two energy channels guiding light out by the splitter: the optical and the plasmonic channels. Groove A is used to couple incident light into the plasmonic channel. Groove B functions as a plasmonic scatter. We demonstrate that the energy transfer through plasmonic path is dominant in the beam splitter. We find that more than four times the energy is transferred by the plasmonic channel using structures A and B. We show that the plasmonic waves scattered by B can be converted into light waves. These light waves redistribute the transmitted energy through interference with the field transmitted from the nanoslit. Therefore, different beam splitting effects are achieved by simply changing the interference conditions between the scattered waves and the transmitted waves. The impact of the width and height of groove B are also investigated. It is found that the plasmonic scattering of B is changed into light scattering with increase of the width and the height of B. These devices have potential applications in optical sampling, signal processing, and integrated optical circuits. PMID:21647248

Identifying the Minimum Model Features to Replicate Historic Morphodynamics of a Juvenile Delta

NASA Astrophysics Data System (ADS)

Czapiga, M. J.; Parker, G.

2017-12-01

We introduce a quasi-2D morphodynamic delta model that improves on past models that require many simplifying assumptions, e.g. a single channel representative of a channel network, fixed channel width, and spatially uniform deposition. Our model is useful for studying long-term progradation rates of any generic micro-tidal delta system with specification of: characteristic grain size, input water and sediment discharges and basin morphology. In particular, we relax the assumption of a single, implicit channel sweeping across the delta topset in favor of an implicit channel network. This network, coupled with recent research on channel-forming Shields number, quantitative assessments of the lateral depositional length of sand (corresponding loosely to levees) and length between bifurcations create a spatial web of deposition within the receiving basin. The depositional web includes spatial boundaries for areas infilling with sands carried as bed material load, as well as those filling via passive deposition of washload mud. Our main goal is to identify the minimum features necessary to accurately model the morphodynamics of channel number, width, depth, and overall delta progradation rate in a juvenile delta. We use the Wax Lake Delta in Louisiana as a test site due to its rapid growth in the last 40 years. Field data including topset/island bathymetry, channel bathymetry, topset/island width, channel width, number of channels, and radial topset length are compiled from US Army Corps of Engineers data for 1989, 1998, and 2006. Additional data is extracted from a DEM from 2015. These data are used as benchmarks for the hindcast model runs. The morphology of Wax Lake Delta is also strongly affected by a pre-delta substrate that acts as a lower "bedrock" boundary. Therefore, we also include closures for a bedrock-alluvial transition and an excess shear rate-law incision model to estimate bedrock incision. The model's framework is generic, but inclusion of individual sub-models, such as those mentioned above, allow us to answer basic research questions without the parameterization necessary in higher resolution models. Thus, this type of model offers an alternative to higher-resolution models.

Component having cooling channel with hourglass cross section

DOEpatents

Campbell, Christian X; Lee, Ching-Pang

2015-04-28

A cooling channel (36, 36B, 63-66) cools inner surfaces (48, 50) of exterior walls (41, 43) of a component (20, 60). Interior side surfaces (52, 54) of the channel converge to a waist (W2), forming an hourglass shaped transverse profile (46). The inner surfaces (48, 50) may have fins (44) aligned with the coolant flow (22). The fins may have a transverse profile (56A, 56B) highest at mid-width of the inner surfaces (48, 50). Turbulators (92) may be provided on the side surfaces (52, 54) of the channel, and may urge the coolant flow toward the inner surfaces (48, 50). Each turbulator (92) may have a peak (97) that defines the waist of the cooling channel. Each turbulator may have a convex upstream side (93). These elements increase coolant flow in the corners (C) of the channel to more uniformly and efficiently cool the exterior walls (41, 43).

Factors affecting distribution of wood, detritus, and sediment in headwater streams draining managed young-growth red alder - Conifer forests in southeast Alaska

USGS Publications Warehouse

Gomi, T.; Johnson, A.C.; Deal, R.L.; Hennon, P.E.; Orlikowska, E.H.; Wipfli, M.S.

2006-01-01

Factors (riparian stand condition, management regimes, and channel properties) affecting distributions of wood, detritus (leaves and branches), and sediment were examined in headwater streams draining young-growth red alder (Alnus rubra Bong.) - conifer riparian forests (40 years old) remained in channels and provided sites for sediment and organic matter storage. Despite various alder-conifer mixtures and past harvesting effects, the abundance of large wood, fine wood, and detritus accumulations significantly decreased with increasing channel bank-full width (0.5-3.5 m) along relatively short channel distances (up to 700 m). Changes in wood, detritus, and sediment accumulations together with changes in riparian stand characteristics create spatial and temporal variability of in-channel conditions in headwater systems. A component of alder within young-growth riparian forests may benefit both wood production and biological recovery in disturbed headwater stream channels. ?? 2006 NRC.

Morphology and spacing of river meander scrolls

NASA Astrophysics Data System (ADS)

Strick, Robert J. P.; Ashworth, Philip J.; Awcock, Graeme; Lewin, John

2018-06-01

Many of the world's alluvial rivers are characterised by single or multiple channels that are often sinuous and that migrate to produce a mosaicked floodplain landscape of truncated scroll (or point) bars. Surprisingly little is known about the morphology and geometry of scroll bars despite increasing interest from hydrocarbon geoscientists working with ancient large meandering river deposits. This paper uses remote sensing imagery, LiDAR data-sets of meandering scroll bar topography, and global coverage elevation data to quantify scroll bar geometry, anatomy, relief, and spacing. The analysis focuses on preserved scroll bars in the Mississippi River (USA) floodplain but also compares attributes to 19 rivers of different scale and depositional environments from around the world. Analysis of 10 large scroll bars (median area = 25 km2) on the Mississippi shows that the point bar deposits can be categorised into three different geomorphological units of increasing scale: individual 'scrolls', 'depositional packages', and 'point bar complexes'. Scroll heights and curvatures are greatest near the modern channel and at the terminating boundaries of different depositional packages, confirming the importance of the formative main channel on subsequent scroll bar relief and shape. Fourier analysis shows a periodic variation in signal (scroll bar height) with an average period (spacing) of 167 m (range 150-190 m) for the Mississippi point bars. For other rivers, a strong relationship exists between the period of scroll bars and the adjacent primary channel width for a range of rivers from 55 to 2042 mis 50% of the main channel width. The strength of this correlation over nearly two orders of magnitude of channel size indicates a scale independence of scroll bar spacing and suggests a strong link between channel migration and scroll bar construction with apparent regularities despite different flow regimes. This investigation of meandering river dynamics and floodplain patterns shows that it is possible to develop a suite of metrics that describe scroll bar morphology and geometry that can be valuable to geoscientists predicting the heterogeneity of subsurface meandering deposits.

Characterizing the transient geomorphic response to base level fall in the northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Zhang, H.; Zhang, P.; Kirby, E.; Pitlick, J.; Anderson, R. S.

2015-12-01

Analyses of hillslope gradient, landscape relief, and channel steepness in the Daxiahe drainage basin along the northeastern margin of the Tibetan Plateau provides evidence of a transient geomorphic response to base level fall along the main stem Yellow River. The upper portions of the watershed are characterized by low-gradient channels and gentle hillslopes and are separated from a steeper, high relief landscape by a series of convex knickzones along channel profiles. Downstream projection of the upper channel profiles implies ~500-600 m of incision, consistent with terrace records of post ~1.7 Ma incision in the Linxia basin. We characterize erosion rates across this transient landscape using both optically-stimulated dating of fluvial terraces and catchment-averaged 10Be concentrations in modern sediment. Both data sets are consistent and suggest erosion/incision rates of ~300 m/Myr below knickpoints and ~50-100 m/Myr above. Field measurements of channel width (n=48) and bankfull discharge (n=9) allow us to determine local scaling relations among channel hydraulic geometry, discharge, and contributing area that we employ to estimate basal shear stress, unit stream power and bedload transport along the main stem of the Daxiahe River. We find a clear downstream increase of incision potential across this transient landscape, consistent with topographic observations and erosion rates. In contrast to recent studies, we find no evidence for adjustment of channel width across the transition from slowly eroding to rapidly eroding portions of the watershed. We hypothesize that this behavior is consistent with detachment-limited models of fluvial incision, despite the presence of significant sediment in channel bed and banks. Our results imply that the controls on hydraulic geometry along actively incising rivers remain incompletely understood.

Geomorphic Classification and Evaluation of Channel Width and Emergent Sandbar Habitat Relations on the Lower Platte River, Nebraska

USGS Publications Warehouse

Elliott, Caroline M.

2011-01-01

This report presents a summary of geomorphic characteristics extracted from aerial imagery for three broad segments of the Lower Platte River. This report includes a summary of the longitudinal multivariate classification in Elliott and others (2009) and presents a new analysis of total channel width and habitat variables. Three segments on the lower 102.8 miles of the Lower Platte River are addressed in this report: the Loup River to the Elkhorn River (70 miles long), the Elkhorn River to Salt Creek (6.9 miles long), and Salt Creek to the Missouri River (25.9 miles long). The locations of these segments were determined by the locations of tributaries potentially significant to the hydrology or sediment supply of the Lower Platte River. This report summarizes channel characteristics as mapped from July 2006 aerial imagery including river width, valley width, channel curvature, and in-channel habitat features. In-channel habitat measurements were not made under consistent hydrologic conditions and must be considered general estimates of channel condition in late July 2006. Longitudinal patterns in these features are explored and are summarized in the context of the longitudinal multivariate classification in Elliott and others (2009) for the three Lower Platte River segments. Detailed descriptions of data collection and classification methods are described in Elliott and others (2009). Nesting data for the endangered interior least tern (Sternula antillarum) and threatened piping plover (Charadrius melodus) from 2006 through 2009 are examined within the context of the multivariate classification and Lower Platte River segments. The widest reaches of the Lower Platte River are located in the segment downstream from the Loup River to the Elkhorn River. This segment also has the widest valley and highest degree of braiding of the three segments and many large vegetated islands. The short segment of river between the Elkhorn River and Salt Creek has a fairly low valley width and high channel sinuosities at larger scales. The segment from Salt Creek to the Missouri River has narrow valleys and generally low channel sinuosity. Tern and plover nest sites from 2006 through 2009 in the multi-scale multivariate classification indicated relative nesting selection of cluster 2 reaches among the four-cluster classification and reaches containing clusters 2, 3, and 6 from the seven-cluster classification. These classes, with the exception of cluster 6 are common downstream from the Elkhorn River. Trends in total channel width indicated that reaches dominated by dark vegetation (islands) are the widest on the Lower Platte River. Reaches with high percentages of dry sand and dry sand plus light vegetation were the narrowest reaches. This suggests that narrow channel reaches have sufficient transport capacity to maintain sandbars under recent (2006) flow regimes and are likely to be most amenable to maintaining tern and plover habitat in the Lower Platte River. Further investigations into the dynamics of emergent sandbar habitat and the effects of bank stabilization on in-channel habitats will require the collection and analysis of new data, particularly detailed elevation information and an assessment of existing bank stabilization structures.

Ion concentrations and velocity profiles in nanochannel electroosmotic flows

NASA Astrophysics Data System (ADS)

Qiao, R.; Aluru, N. R.

2003-03-01

Ion distributions and velocity profiles for electroosmotic flow in nanochannels of different widths are studied in this paper using molecular dynamics and continuum theory. For the various channel widths studied in this paper, the ion distribution near the channel wall is strongly influenced by the finite size of the ions and the discreteness of the solvent molecules. The classical Poisson-Boltzmann equation fails to predict the ion distribution near the channel wall as it does not account for the molecular aspects of the ion-wall and ion-solvent interactions. A modified Poisson-Boltzmann equation based on electrochemical potential correction is introduced to account for ion-wall and ion-solvent interactions. The electrochemical potential correction term is extracted from the ion distribution in a smaller channel using molecular dynamics. Using the electrochemical potential correction term extracted from molecular dynamics (MD) simulation of electroosmotic flow in a 2.22 nm channel, the modified Poisson-Boltzmann equation predicts the ion distribution in larger channel widths (e.g., 3.49 and 10.00 nm) with good accuracy. Detailed studies on the velocity profile in electro-osmotic flow indicate that the continuum flow theory can be used to predict bulk fluid flow in channels as small as 2.22 nm provided that the viscosity variation near the channel wall is taken into account. We propose a technique to embed the velocity near the channel wall obtained from MD simulation of electroosmotic flow in a narrow channel (e.g., 2.22 nm wide channel) into simulation of electroosmotic flow in larger channels. Simulation results indicate that such an approach can predict the velocity profile in larger channels (e.g., 3.49 and 10.00 nm) very well. Finally, simulation of electroosmotic flow in a 0.95 nm channel indicates that viscosity cannot be described by a local, linear constitutive relationship that the continuum flow theory is built upon and thus the continuum flow theory is not applicable for electroosmotic flow in such small channels.

Numerical Analysis of the Heat Transfer Characteristics within an Evaporating Meniscus

NASA Astrophysics Data System (ADS)

Ball, Gregory

A numerical analysis was performed as to investigate the heat transfer characteristics of an evaporating thin-film meniscus. A mathematical model was used in the formulation of a third order ordinary differential equation. This equation governs the evaporating thin-film through use of continuity, momentum, energy equations and the Kelvin-Clapeyron model. This governing equation was treated as an initial value problem and was solved numerically using a Runge-Kutta technique. The numerical model uses varying thermophysical properties and boundary conditions such as channel width, applied superheat, accommodation coefficient and working fluid which can be tailored by the user. This work focused mainly on the effects of altering accommodation coefficient and applied superheat. A unified solution is also presented which models the meniscus to half channel width. The model was validated through comparison to literature values. In varying input values the following was determined; increasing superheat was found to shorten the film thickness and greatly increase the interfacial curvature overshoot values. The effect of decreasing accommodation coefficient lengthened the thin-film and retarded the evaporative effects.

Paleo-hydraulic Reconstructions of Topographically Inverted River Deposits on Earth and Mars

NASA Astrophysics Data System (ADS)

Hayden, A.; Lamb, M. P.; Fischer, W. W.; Ewing, R. C.; McElroy, B. J.

2015-12-01

River deposits are one of the keys to understanding the history of flowing water and sediment on Earth and Mars. Deposits of some ancient Martian rivers have been topographically inverted resulting in sinuous ridges visible from orbit. However, it is unclear what aspects of the fluvial deposits these ridges represent, so reconstructing paleo-hydraulics from ridge geometry is complicated. Most workers have assumed that ridges represent casts of paleo-river channels, such that ridge widths and slopes, for example, can be proxies for river widths and slopes at some instant in time. Alternatively, ridges might reflect differential erosion of extensive channel bodies, and therefore preserve a rich record of channel conditions and paleoenvironment over time. To explore these hypotheses, we examined well exposed inverted river deposits in the Jurassic Morrison and Early Cretaceous Cedar Mountain Formations across the San Rafael Swell of central Utah. We mapped features on foot and by UAV, measured stratigraphic sections and sedimentary structures to constrain deposit architecture and river paleo-hydraulics, and used field observations and drainage network analyses to constrain recent erosion. Our work partly confirms earlier work in that the local trend of the ridge axis generally parallels paleo-flow indicators. However, ridge relief is much greater than reconstructed channel depths, and ridge widths vary from zero to several times the reconstructed channel width. Ridges instead appear to record a rich history of channel lateral migration, floodplain deposition, and soil development over significant time. The ridge network is disjointed owing to active modern fluvial incision and scarp retreat. Our results suggest that ridge geometry alone contains limited quantitative information about paleo-rivers, and that stratigraphic sections and observations of sedimentary structures within ridge-forming deposits are necessary to constrain ancient river systems on Mars.

On the channel width-dependence of the thermal conductivity in ultra-narrow graphene nanoribbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karamitaheri, Hossein; Neophytou, Neophytos, E-mail: N.Neophytou@warwick.ac.uk

The thermal conductivity of low-dimensional materials and graphene nanoribbons, in particular, is limited by the strength of line-edge-roughness scattering. One way to characterize the roughness strength is the dependency of the thermal conductivity on the channel's width in the form W{sup β}. Although in the case of electronic transport, this dependency is very well studied, resulting in W{sup 6} for nanowires and quantum wells and W{sup 4} for nanoribbons, in the case of phonon transport it is not yet clear what this dependence is. In this work, using lattice dynamics and Non-Equilibrium Green's Function simulations, we examine the width dependencemore » of the thermal conductivity of ultra-narrow graphene nanoribbons under the influence of line edge-roughness. We show that the exponent β is in fact not a single well-defined number, but it is different for different parts of the phonon spectrum depending on whether phonon transport is ballistic, diffusive, or localized. The exponent β takes values β < 1 for semi-ballistic phonon transport, values β ≫ 1 for sub-diffusive or localized phonons, and β = 1 only in the case where the transport is diffusive. The overall W{sup β} dependence of the thermal conductivity is determined by the width-dependence of the dominant phonon modes (usually the acoustic ones). We show that due to the long phonon mean-free-paths, the width-dependence of thermal conductivity becomes a channel length dependent property, because the channel length determines whether transport is ballistic, diffusive, or localized.« less

Pre-Restoration Geomorphic Characteristics of Minebank Run, Baltimore County, Maryland, 2002-04

USGS Publications Warehouse

Doheny, Edward J.; Starsoneck, Roger J.; Mayer, Paul M.; Striz, Elise A.

2007-01-01

Data collected from 2002 through 2004 were used to assess geomorphic characteristics and geomorphic changes over time in a selected reach of Minebank Run, a small urban watershed near Towson, Maryland, prior to its physical restoration in 2004 and 2005. Longitudinal profiles of the channel bed, water surface, and bank features were developed from field surveys. Changes in cross-section geometry between field surveys were documented. Grain-size distributions for the channel bed and banks were developed from pebble counts and laboratory analyses. Net changes in the elevation of the channel bed over time were documented at selected locations. Rosgen Stream Classification was used to classify the stream channel according to morphological measurements of slope, entrenchment ratio, width-to-depth ratio, sinuosity, and median-particle diameter of the channel materials. An analysis of boundary shear stress in the vicinity of the streamflow-gaging station was conducted by use of hydraulic variables computed from cross-section surveys and slope measurements derived from crest-stage gages in the study reach. Analysis of the longitudinal profiles indicated noticeable changes in the percentage and distribution of riffles, pools, and runs through the study reach between 2002 and 2004. Despite major changes to the channel profile as a result of storm runoff events, the overall slope of the channel bed, water surface, and bank features remained constant at about 1 percent. The cross-sectional surveys showed net increases in cross-sectional area, mean depth, and channel width at several locations between 2002 and 2004, which indicate channel degradation and widening. Two locations were identified where significant amounts of sediment were being stored in the study reach. Data from scour chains identified several locations where maximum scour ranged from 1.0-1.4 feet during storm events. Bank retreat varied widely throughout the study reach and ranged from 0.2 feet to as much as 7.9 feet. Sequential measurements of bed elevation in selected locations indicated as much as 2 feet of channel degradation in one location during a storm event in May 2004 and identified pulses of sediment that were gradually transported through the study reach during the monitoring period. Particle-size analyses of channel bed materials indicated a median particle diameter of 20.5 millimeters (coarse gravel) for the study reach, with more than 24 percent being sand particles (greater than 0.062 millimeters). Analyses of bank samples showed finer-grained material composing the channel banks, predominantly silt/clay or a mixture of silt/clay (less than 0.062 millimeters) and very fine to coarse sand. The Minebank Run stream channel was classified as a B4c channel, based on morphological descriptions from the Rosgen Stream Classification System. The B4c classification describes a single-thread stream channel with a moderate entrenchment ratio of 1.4 to 2.2; a width-to-depth ratio greater than 12; moderate sinuosity of 1.2 or greater; a water-surface slope of less than 2 percent; and a median-particle diameter in the gravel range of 2 to 64 millimeters. Analysis of boundary shear stress indicated larger mean velocities and boundary shear stress values for Minebank Run when compared to relations for non-urban B channel types developed by Rosgen. The slope of the regression line for mean velocity versus boundary shear stress at Minebank Run was considerably less than slopes developed by Rosgen for non-urban channel types. This indicates that relatively small increases in mean velocity can result in large increases in boundary shear stress in stream channels with highly developed watersheds, such as Minebank Run.

Electrokinetic mixing vortices due to electrolyte depletion at microchannel junctions.

PubMed

Takhistov, Paul; Duginova, Ksenia; Chang, Hsueh-Chia

2003-07-01

Due to electric field leakage across sharp corners, the irrotational character of Ohmic electroosmotic flow is violated. Instead, we demonstrate experimentally and theoretically evidence of electrolyte depletion and vortex separation in electroosmotic flow around a junction between wide and narrow channels. When the penetration length of the electric field exceeds the width of the narrow channel and if the electric field is directed from the narrow to the wide channel, the electromigration of ions diminishes significantly at the junction end of the narrow channel due to this leakage. Concentration depletion then develops at that location to maintain current balance but it also increases the corner zeta potential and the local electroosmotic slip velocity. A back pressure gradient hence appears to maintain flow balance and, at a sufficient magnitude, generates a pair of vortices.

Broadening of Analyte Streams due to a Transverse Pressure Gradient in Free-Flow Isoelectric Focusing

PubMed Central

Dutta, Debashis

2017-01-01

Pressure-driven cross-flows can arise in free-flow isoelectric focusing systems (FFIEF) due to a non-uniform electroosmotic flow velocity along the channel width induced by the pH gradient in this direction. In addition, variations in the channel cross-section as well as unwanted differences in hydrostatic heads at the buffer/sample inlet ports can also lead to such pressure-gradients which besides altering the equilibrium position of the sample zones have a tendency to substantially broaden their widths deteriorating the separations. In this situation, a thorough assessment of stream broadening due to transverse pressure-gradients in FFIEF devices is necessary in order to establish accurate design rules for the assay. The present article describes a mathematical framework to estimate the noted zone dispersion in FFIEF separations based on the method-of-moments approach under laminar flow conditions. A closed-form expression has been derived for the spatial variance of the analyte streams at their equilibrium positions as a function of the various operating parameters governing the assay performance. This expression predicts the normalized stream variance under the chosen conditions to be determined by two dimensionless Péclet numbers evaluated based on the transverse pressure-driven and electrophoretic solute velocities in the separation chamber, respectively. Moreover, the analysis shows that while the stream width can be expected to increase with an increase in the value of the first Péclet number, the opposite trend will be followed with respect to the latter. The noted results have been validated using Monte Carlo simulations that also establish a time/length scale over which the predicted equilibrium stream width is attained in the system. PMID:28081900

Channel plate for DNA sequencing

DOEpatents

Douthart, R.J.; Crowell, S.L.

1998-01-13

This invention is a channel plate that facilitates data compaction in DNA sequencing. The channel plate has a length, a width and a thickness, and further has a plurality of channels that are parallel. Each channel has a depth partially through the thickness of the channel plate. Additionally an interface edge permits electrical communication across an interface through a buffer to a deposition membrane surface. 15 figs.

Multi-objective optimization of MOSFETs channel widths and supply voltage in the proposed dual edge-triggered static D flip-flop with minimum average power and delay by using fuzzy non-dominated sorting genetic algorithm-II.

PubMed

Keivanian, Farshid; Mehrshad, Nasser; Bijari, Abolfazl

2016-01-01

D Flip-Flop as a digital circuit can be used as a timing element in many sophisticated circuits. Therefore the optimum performance with the lowest power consumption and acceptable delay time will be critical issue in electronics circuits. The newly proposed Dual-Edge Triggered Static D Flip-Flop circuit layout is defined as a multi-objective optimization problem. For this, an optimum fuzzy inference system with fuzzy rules is proposed to enhance the performance and convergence of non-dominated sorting Genetic Algorithm-II by adaptive control of the exploration and exploitation parameters. By using proposed Fuzzy NSGA-II algorithm, the more optimum values for MOSFET channel widths and power supply are discovered in search space than ordinary NSGA types. What is more, the design parameters involving NMOS and PMOS channel widths and power supply voltage and the performance parameters including average power consumption and propagation delay time are linked. To do this, the required mathematical backgrounds are presented in this study. The optimum values for the design parameters of MOSFETs channel widths and power supply are discovered. Based on them the power delay product quantity (PDP) is 6.32 PJ at 125 MHz Clock Frequency, L = 0.18 µm, and T = 27 °C.

Burst pressure of phaseguide structures of different heights in all-polymer microfluidic channels

NASA Astrophysics Data System (ADS)

Garbarino, Francesca; Kistrup, Kasper; Rizzi, Giovanni; Fougt Hansen, Mikkel

2017-12-01

We present an experimental investigation of the burst/overflow pressure of water and a representative surfactant-containing buffer in microfluidic channels with phaseguide structures oriented at an angle of 90° to the channel length as a function of their height, h . The all-polymer chips were fabricated by injection moulding and sealed by ultrasonic welding. Channels with a height of 200 μ m and widths of 1 mm or 3 mm were investigated for five values of h between 8 μ m and 82 μ m. Phaseguide structures without branches and with branches at angles α   =  45°, 60° and 75° were studied. All phaseguide structures were found able to pin both liquids and the burst pressure was found to increase approximately linearly with the height of the phaseguide from about 100-350 Pa for water and from about 25-200 Pa for the buffer. The burst pressure was found not to depend on the channel width and it was only weakly influenced by the presence of a branch on the phaseguide. For phaseguides with a branch, the liquid was always found to burst at the branch location. The measured burst pressures were compared to those estimated using a simple theory. The knowledge obtained in this study enables simple tuning of liquid spreading and overflow in microfluidic channels by use of phaseguide structures with different heights and it also provides a set of systematic experimental data to be compared with simulations/theory.

Quantitative Relationships Linking Rock Strength to Channel Morphology: A Case Study in Central Arizona

NASA Astrophysics Data System (ADS)

Larimer, J. E.; Yanites, B.

2016-12-01

River morphology is a consequence of the erosive forces acting on the channel boundary and the resisting forces that limit erosion. For bedrock rivers, the erosive forces are generated by the stresses exerted by impacting sediment and flowing water, while the resisting forces are controlled by the internal strength regime of the local rock. We investigate the susceptibility of different rock types to different erosional processes (i.e. abrasion and plucking) and how changes in channel morphology reflect rock strength properties across lithologic boundaries. The bedrock rivers in the Prescott National Forest, AZ flow over a number of rock types with variable strength including sedimentary, igneous, and metamorphic lithologies providing a natural experiment to quantify the influence of rock strength on channel morphology. We collected bedrock samples and channel surveys from 12 different rock types. Rock-strength and rock-mass properties include compressive strength, tensile strength, fatigue strength, decimeter scale P-wave velocity (varies by 8-fold), Schmidt rebound value, fracture spacing, fracture aperture, and slake durability (as a proxy for weathering susceptibility. Morphological measurements include channel width, channel steepness (varies by 10-fold), and grain size distribution. To distinguish between the major mechanisms of erosion we measure bedrock surface roughness factor at the centimeter scale. Preliminary results show that channel steepness (ksn) increases with P-wave velocity while normalized channel width (kwn) decreases with P-wave velocity. We use these data to quantify scaling relationships of channel geometry with rock strength properties. We consider the results in the context of the driving mechanistic process to develop new quantitative understandings of how rock strength properties influence the efficiency of erosion processes and how rock strength is reflected in river morphology. By comparing the results among different rock types in a landscape subject to spatially consistent tectonic and climatic influence, our work seeks to advance process-based river erosion models through field and laboratory measurements.

Proton Resonance Spectroscopy in CALCIUM-40.

NASA Astrophysics Data System (ADS)

Warthen, Barry Joseph

1987-09-01

The differential cross sections for the ^{39}K(p,p_{ rm o})^{39}K and ^{39}K(p,alpha_ {rm o})^{36}Ar reactions have been measured for E_{ rm p} = 1.90 to 4.02 MeV at laboratory angles theta = 90^ circ, 108^circ, 150^circ and 165^ circ. Data were taken with the Triangle Universities Nuclear Laboratory (TUNL) KN Van de Graaff accelerator and the associated high resolution system. The targets consisted of 1-2 mug/cm^2 of potassium carbonate (K_2CO _3), enriched to 99.97% ^{39}K, evaporated onto gold coated carbon backings. Excitation functions were measured in proton energy steps varying from 100 to 400 eV. The energy region studied corresponds to an excitation energy range in the ^{40}Ca nucleus of E_{rm x} = 10.2 to 12.3 MeV. A multi-level multi-channel R-matrix based computer code was used to fit the experimental excitation functions. Resonance parameters obtained include resonance energy, spin, parity, partial widths, and channel spin and orbital angular momentum mixing ratios. Of the 248 resonances observed in the proton channel, 148 were also observed in the alpha channel. A fit to the observed level density yielded a nuclear temperature of 1.5 MeV. The data were compared with predictions of statistical theories of energy levels for both level spacing and reduced width distributions. The alpha reduced widths agree with the Porter-Thomas distribution and suggest that only 5-10% of the states with alpha widths were not observed. The summed strength in each of the alpha channels represents a significant fraction of the Wigner limit for these channels. The proton channels, on the other hand, generally have much smaller fractions. The two proton s-wave strength functions are equal and thus show no evidence for spin-exchange forces in the nucleon-nucleus interaction.

Numerical simulation of electroosmotic flow in rough microchannels using the lattice Poisson-Nernst-Planck methods

NASA Astrophysics Data System (ADS)

Kamali, Reza; Soloklou, Mohsen Nasiri; Hadidi, Hooman

2018-05-01

In this study, coupled Lattice Boltzmann method is applied to solve the dynamic model for an electroosmotic flow and investigate the effects of roughness in a 2-D flat microchannel. In the present model, the Poisson equation is solved for the electrical potential, the Nernst- Planck equation is solved for the ion concentration. In the analysis of electroosmotic flows, when the electric double layers fully overlap or the convective effects are not negligible, the Nernst-Planck equation must be used to find the ionic distribution throughout the microchannel. The effects of surface roughness height, roughness interval spacing and roughness surface potential on flow conditions are investigated for two different configurations of the roughness, when the EDL layers fully overlap through the microchannel. The results show that in both arrangements of roughness in homogeneously charged rough channels, the flow rate decreases by increasing the roughness height. A discrepancy in the mass flow rate is observed when the roughness height is about 0.15 of the channel width, which its average is higher for the asymmetric configuration and this difference grows by increasing the roughness height. In the symmetric roughness arrangement, the mass flow rate increases until the roughness interval space is almost 1.5 times the roughness width and it decreases for higher values of the roughness interval space. For the heterogeneously charged rough channel, when the roughness surface potential ψr is less than channel surface potential ψs , the net charge density increases by getting far from the roughness surface, while in the opposite situation, when ψs is more than ψr , the net charge density decreases from roughness surface to the microchannel middle center. Increasing the roughness surface potential induces stronger electric driving force on the fluid which results in larger velocities in the flow.

Eruption Constraints for a Young Channelized Lava Flow, Marte Vallis, Mars

NASA Technical Reports Server (NTRS)

Therkelsen, J. P.; Santiago, S. S.; Grosfils, E. B.; Sakimoto, S. E. H.; Mendelson, C. V.; Bleacher, J. E.

2001-01-01

This study constrains flow rates for a specific channelized lava flow in Marte Vallis, Mars. We measured slope-gradient, channel width, and channel depth. Our results are similar to other recent studies which suggests similarities to long, terrestrial basaltic flow. Additional information is contained in the original extended abstract.

75 FR 5768 - Intent To Prepare a Draft Environmental Impact Statement To Evaluate Improvements to the Federal...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

... DEPARTMENT OF DEFENSE Department of the Army; Corps of Engineers Intent To Prepare a Draft... Feasibility Report investigated increased widths and depths in the Pascagoula and Bayou Casotte navigation... Gulf Entrance channel to 44 feet by 550 feet from the 44-foot depth contour in the Gulf of Mexico to...

Do river channels decrease in width downstream on Distributive Fluvial Systems? An evaluation of modern mega-fans

NASA Astrophysics Data System (ADS)

Espinoza, T. N.; Scuderi, L. A.; Weissmann, G. S.; Hartley, A. J.

2014-12-01

Recent studies on aggradational continental sedimentary basins globally show that fluvial deposits in most modern sedimentary basins are dominated Distributive Fluvial Systems (DFS). DFS's are identified by: (1) pattern of channels and floodplain deposits that radiate outward from an apex located where the river enters the sedimentary basin, (2) deposition where an alluvial system becomes unconfined upon entering the sedimentary basin, (3) broadly fan shaped deposit that is convex upward across the DFS and concave upward down-fan, and (4) if the DFS is incised, an intersection point above which the alluvial system is held in an incised valley and below which it distributes sediment across an active depositional lobe. Several papers about DFS hypothesized that rivers on DFS decrease in size down-fan. We are testing this hypothesis through evaluation of LANDSAT and STRM data from large DFS described by Hartley et al (2010). We use ArcGIS to: (1) open the images and merge them together if there are more than one image corresponding to the DFS being studied, (2) use a Maximum Likelihood Analysis in six classes to segment different features on the DFS (e.g. exposed sands, water, vegetation, and other fan environments), (3) isolate the classes that correspond to the active channel belt (e.g., exposed sand bars and water), (4) divide the active channel belt into 1000 m long sections, (5) determine the area of active channel belt in each section, and (6) calculate the average width of the river in each section (e.g., W = area/1000m). We present our result for each DFS river on a graph that shows the change in width downstream. Our final product will be a dataset that contains width versus distance down-fan from the apex for as many of the large DFS from Hartley et al (2010) as possible. If the hypothesis is supported, the decrease in width could have a substantial predictive significance on sandstone geometry in fluvial successions.

Electrically controlled wire-channel GaN/AlGaN transistor for terahertz plasma applications

NASA Astrophysics Data System (ADS)

Cywiński, G.; Yahniuk, I.; Kruszewski, P.; Grabowski, M.; Nowakowski-Szkudlarek, K.; Prystawko, P.; Sai, P.; Knap, W.; Simin, G. S.; Rumyantsev, S. L.

2018-03-01

We report on a design of fin-shaped channel GaN/AlGaN field-effect transistors developed for studying resonant terahertz plasma oscillations. Unlike common two dimensional FinFET transistor design, the gates were deposited only to the sides of the two dimensional electron gas channel, i.e., metal layers were not deposited on the top of the AlGaN. This side gate configuration allowed us to electrically control the conductivity of the channel by changing its width while keeping the carrier density and mobility virtually unchanged. Computer simulations and analytical model describe well the general shape of the characteristics. The side gate control of the channel width of these transistors allowed us to eliminate the so-called oblique plasma wave modes and paves the way towards future terahertz detectors and emitters using high quality factor plasma wave resonances.

Study on the reduction and hysteresis effect of soil nitrogen pollution by Alfalfa in channel buffer bank

NASA Astrophysics Data System (ADS)

Chi, Yixia; Xue, Lianqing; Zhang, Zhanyu; Li, Dongying

2018-01-01

Based on the simulation experiments of solute transport in channel buffer bank and pot experiments, this study analyzed the transport of nitrogen pollution from farmland drains along the South-North Water Transfer east route project; and compared the nitrogen transport rule and purification effect of alfalfa in channel buffer bank soil under situations of bare land and alfalfa mulching. The results showed that: (1) soil nitrogen content decreased gradually with the width increase of channel buffer bank by the soil adsorption and decomposition; (2) the migration rates of nitrogen were 0.06 g·kg-1 by the alfalfa mulching; (3) the removed rates of nitrogen from the soil were 0.088 g·kg-1 by cutting alfalfa; (4) the residual nitrogen of soil with alfalfa was 10% of the bare land. Alfalfa in channel buffer bank had obvious reduction and hysteresis effect to soil nitrogen pollution.

An AC electroosmotic micropump for circular chromatographic applications.

PubMed

Debesset, S; Hayden, C J; Dalton, C; Eijkel, J C T; Manz, A

2004-08-01

Flow rates of up to 50 microm s(-1) have been successfully achieved in a closed-loop channel using an AC electroosmotic pump. The AC electroosmotic pump is made of an interdigitated array of unequal width electrodes located at the bottom of a channel, with an AC voltage applied between the small and the large electrodes. The flow rate was found to increase linearly with the applied voltage and to decrease linearly with the applied frequency. The pump is expected to be suitable for circular chromatography for the following reasons: the driving forces are distributed over the channel length and the pumping direction is set by the direction of the interdigitated electrodes. Pumping in a closed-loop channel can be achieved by arranging the electrode pattern in a circle. In addition the inherent working principle of AC electroosmotic pumping enables the independent optimisation of the channel height or the flow velocity.

H-tailored surface conductivity in narrow band gap In(AsN)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velichko, A. V., E-mail: amalia.patane@nottingham.ac.uk, E-mail: anton.velychko@nottingham.ac.uk; Patanè, A., E-mail: amalia.patane@nottingham.ac.uk, E-mail: anton.velychko@nottingham.ac.uk; Makarovsky, O.

2015-01-12

We show that the n-type conductivity of the narrow band gap In(AsN) alloy can be increased within a thin (∼100 nm) channel below the surface by the controlled incorporation of H-atoms. This channel has a large electron sheet density of ∼10{sup 18 }m{sup −2} and a high electron mobility (μ > 0.1 m{sup 2}V{sup −1}s{sup −1} at low and room temperature). For a fixed dose of impinging H-atoms, its width decreases with the increase in concentration of N-atoms that act as H-traps thus forming N-H donor complexes near the surface.

Geologic Tests for Snowmelt Runoff on Early Mars

NASA Astrophysics Data System (ADS)

Kite, E. S.; Sneed, J.; Mayer, D. P.

2017-12-01

Data from the Curiosity rover have sharpened the question: was Early Mars climate warm enough for rainfall, or was the climate cold? The hypothesis of a cold (snow-and-ice melt) climate on Early Mars can be tested using runoff production. Runoff production cannot exceed snowmelt rate in a cold climate. Therefore, high runoff production would rule out cold conditions, and would suggest rain (or catastrophic melting of snow). How can runoff production be reliably measured? To constrain runoff production, the lead author is measuring paleochannel widths and meander wavelengths for Early Mars watersheds with well-defined drainage area. The measurement method is the same as in Kite et al., EPSL, 2015. >250 channel-width measurements and 89 meander wavelength measurements are included, representing 158 drainage areas. The catalog emphasizes better-preserved (post-Noachian) paleochannels, but includes a re-survey of previously-reported paleochannel width and wavelength measurement sites. Channel widths and wavelengths are a proxy for paleodischarge. Discharge (m3/s) can be divided by drainage area (m2) to obtain a lower bound on runoff-production (mm/hr). If runoff production >(1-3) mm/hr, then a seasonal melting snow-and-ice climate is strongly disfavored. However, high runoff production would be consistent with rainfall. Initial results will be reported at the conference. The figure shows the locations of measurement sites for Early Mars channel width (black) and meander wavelength (red).

Ultra-narrow pulse generator with precision-adjustable pulse width

NASA Astrophysics Data System (ADS)

Fu, Zaiming; Liu, Hanglin

2018-05-01

In this paper, a novel ultra-narrow pulse generation approach is proposed. It is based on the decomposition and synthesis of pulse edges. Through controlling their relative delay, an ultra-narrow pulse could be generated. By employing field programmable gate array digital synthesis technology, the implemented pulse generator is with programmable ability. The amplitude of pulse signals is controlled by the radio frequency amplifiers and bias tees, and high precision can be achieved. More importantly, the proposed approach can break through the limitation of device's propagation delay and optimize the resolution and the accuracy of the pulse width significantly. The implemented pulse generator has two channels, whose minimum pulse width, frequency range, and amplitude range are 100 ps, 15 MHz-1.5 GHz, and 0.1 Vpp-1.8 Vpp, respectively. Both resolution of pulse width and channel delay are 1 ps, and amplitude resolution is 10 mVpp.

Confinement-induced liquid ordering investigated by x-ray phase retrieval

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bunk, Oliver; Diaz, Ana; Pfeiffer, Franz

2007-02-15

Using synchrotron x-ray diffraction, we have determined the ensemble-averaged density profile of colloidal fluids within confining channels of different widths. We observe an oscillatory ordering-disordering behavior of the colloidal particles as a function of the channel width, while the colloidal solution remains in the liquid state. This phenomenon has been suggested by surface force studies of hard-sphere fluids and also theoretically predicted, but here we see it by direct measurements of the structure for comparable systems.

Three-body DD{pi} dynamics for the X(3872)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baru, V.; Filin, A. A.; Hanhart, C.

2011-10-01

We investigate the role played by the three-body DD{pi} dynamics on the near-threshold resonance X(3872) charmonium state, which is assumed to be formed by nonperturbative DD{sup *} dynamics. It is demonstrated that, as compared to the naive static-pions approximation, the imaginary parts that originate from the inclusion of dynamical pions reduce substantially the width from the DD{pi} intermediate state. In particular, for a resonance peaked at 0.5 MeV below the D{sup 0}D{sup *0} threshold, this contribution to the width is reduced by about a factor of 2, and the effect of the pion dynamics on the width grows as longmore » as the resonance is shifted towards the D{sup 0}D{sup 0{pi}0} threshold. Although the physical width of the X is dominated by inelastic channels, our finding should still be of importance for the X line shapes in the DD{pi} channel below DD{sup *} threshold. For example, in the scattering length approximation, the imaginary part of the scattering length includes effects of all the pion dynamics and does not only stem from the D{sup *} width. Meanwhile, we find that another important quantity for the X phenomenology, the residue at the X pole, is weakly sensitive to dynamical pions. In particular, we find that the binding energy dependence of this quantity from the full calculation is close to that found from a model with pointlike DD{sup *} interactions only, consistent with earlier claims. Coupled-channel effects (inclusion of the charged DD{sup *} channel) turn out to have a moderate impact on the results.« less

Investigation on onset voltage and conduction channel temperature in voltage-induced metal-insulator transition of vanadium dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Joonseok; Kim, Howon; Ju, Honglyoul, E-mail: tesl@yonsei.ac.kr

2016-03-28

The characteristics of onset voltages and conduction channel temperatures in the metal-insulator transition (MIT) of vanadium dioxide (VO{sub 2}) devices are investigated as a function of dimensions and ambient temperature. The MIT onset voltage varies from 18 V to 199 V as the device length increases from 5 to 80 μm at a fixed width of 100 μm. The estimated temperature at local conduction channel increases from 110 to 370 °C, which is higher than the MIT temperature (67 °C) of VO{sub 2}. A simple Joule-heating model is employed to explain voltage-induced MIT as well as to estimate temperatures of conduction channel appearing after MIT inmore » various-sized devices. Our findings on VO{sub 2} can be applied to micro- to nano-size tunable heating devices, e.g., microscale scanning thermal cantilevers and gas sensors.« less

Radial resolution enhancement of the NSTX Thomson scattering diagnostic.

PubMed

LeBlanc, B P; Diallo, A; Labik, G; Stevens, D R

2012-10-01

Current magnetic confinement plasma physics research has increased the demand for radial resolution in profile diagnostics, in particular in the edge and pedestal regions. On NSTX, an upgrade of the existing multi-point Thomson scattering diagnostic has been implemented in order to respond to the research program needs. Twelve new radial channels have been added bringing the total number of positions to 42. Four previously un-instrumented fiber bundles were put in service. Eight existing "active" fiber bundles were divided in two sub-bundles each in order to increase spatial resolution. Twelve radial channels now cover the pedestal region with a resolution near one centimeter. Fifteen radial channels cover the core and internal transport barrier regions. Two additional channels were added, one near the inner edge and one in the outer scrape-off layer. The intersection of the focused viewing optics field of view with a finite-width laser beam results in major-radius cross talk between adjacent fiber sub-bundles. A discussion and calculation of the cross talk will be presented.

Effects of large floods on channel width: recent insights from Italian rivers

NASA Astrophysics Data System (ADS)

Scorpio, Vittoria; Righini, Margherita; Amponsah, William; Crema, Stefano; Ciccarese, Giuseppe; Nardi, Laura; Zoccatelli, Davide; Borga, Marco; Cavalli, Marco; Comiti, Francesco; Corsini, Alessandro; Marchi, Lorenzo; Rinaldi, Massimo; Surian, Nicola

2017-04-01

Variations of channel morphology occurring during large flood events (recurrence interval > 50-100 years.) are very often the cause of damages to buildings and infrastructures, as well as of casualties. However, our knowledge of such processes remains poor, as is our capability to predict them. Post-event campaigns documenting channel changes and linking them to hydrological and morphological factors thus bear an enormous value for both the scientific community and river management agencies. We present the results of an analysis on the geomorphic response associated to 4 large floods that occurred between October 2011 and September 2015, affecting several catchments in Northern Italy (Magra-Vara, Trebbia, Nure rivers) and Sardinia (Posada and Mannu di Bitti rivers), characterized by different climatic, lithological and geomorphological settings. The analysis considered more than 400 channel reaches characterized by a drainage area ranging from 39 to 1,100 km2 and featuring a wide range of lateral confinement, mostly within the partly- and unconfined conditions. The approach to flood analysis encompassed: (i) hydrological and hydraulic analysis; (ii) analysis of sediment delivery by landslides to the channel network; (iii) GIS-based and field assessment of morphological channel modifications. For the Nure River flood event (September 2015) a quantitative assessment on average bed level variations was also carried out. Return period for maximum hourly rainfall intensities and peak water discharges exceeded in all basins 100 yr, in some cases even 300 yr. Very high unit peak discharges were estimated, reaching 8.8 m3 s-1km-2 in the Nure River (205 km2) and up to 30 m3 s-1km-2in few Magra River tributaries (5-10 km2). Notable channel widening (post-flood width / pre-flood width > 1.1) occurred in 83% of studied reaches, and it was found more relevant in the channels with narrower initial width, i.e. along the relatively steep tributaries. For these tributaries, the ratio between post-flood and pre-flood width presents an average value of 4.2, with a maximum approaching 20. In the main river channels, due to the presence of wider sections and lower slope, the ratio resulted < 5, on average 1.3. The analysis of width ratio vs. flood peak unit stream power shows that the minimum unit stream power required to cause relevant widening was about 500 Wm-2. Nonetheless, some reaches affected by unit stream power as high as 4,000 Wm-2 exhibited limited or no widening at all. Indeed, a statistical analysis on the relationship between widening and both morphological and hydraulic controlling factors indicates that unit stream power and confinement index were the most relevant variables, whereas sediment input from mass wasting processes seems to have a localized influence. Remarkably, the analysis of subset referring to Trebbia and Nure basins showed that channel widening is strongly associated to bed aggradation, and that steeper tributaries underwent higher aggradation despite their larger sediment transport capacity. These results points out that geomorphic changes due to large floods are controlled by several factors that induce a highly variable pattern of change even within the same river basin.

Lubiprostone ameliorates the cystic fibrosis mouse intestinal phenotype.

PubMed

De Lisle, Robert C; Mueller, Racquel; Roach, Eileen

2010-09-15

Cystic fibrosis (CF) is caused by mutations in the CFTR gene that impair the function of CFTR, a cAMP-regulated anion channel. In the small intestine loss of CFTR function creates a dehydrated, acidic luminal environment which is believed to cause an accumulation of mucus, a phenotype characteristic of CF. CF mice have small intestinal bacterial overgrowth, an altered innate immune response, and impaired intestinal transit. We investigated whether lubiprostone, which can activate the CLC2 Cl- channel, would improve the intestinal phenotype in CF mice. Cftr(tm1UNC) (CF) and wildtype (WT) littermate mice on the C57BL/6J background were used. Lubiprostone (10 μg/kg-day) was administered by gavage for two weeks. Mucus accumulation was estimated from crypt lumen widths in periodic acid-Schiff base, Alcian blue stained sections. Luminal bacterial load was measured by qPCR for the bacterial 16S gene. Gastric emptying and small intestinal transit in fasted mice were assessed using gavaged rhodamine dextran. Gene expression was evaluated by Affymetrix Mouse430 2.0 microarray and qRT-PCR. Crypt width in control CF mice was 700% that of WT mice (P < 0.001). Lubiprostone did not affect WT crypt width but, unexpectedly, increased CF crypt width 22% (P = 0.001). Lubiprostone increased bacterial load in WT mice to 490% of WT control levels (P = 0.008). Conversely, lubiprostone decreased bacterial overgrowth in CF mice by 60% (P = 0.005). Lubiprostone increased gastric emptying at 20 min postgavage in both WT (P < 0.001) and CF mice (P < 0.001). Lubiprostone enhanced small intestinal transit in WT mice (P = 0.024) but not in CF mice (P = 0.377). Among other innate immune markers, expression of mast cell genes was elevated 4-to 40-fold in the CF intestine as compared to WT, and lubiprostone treatment of CF mice decreased expression to WT control levels. These results indicate that lubiprostone has some benefits for the CF intestinal phenotype, especially on bacterial overgrowth and the innate immune response. The unexpected observation of increased mucus accumulation in the crypts of lubiprostone-treated CF mice suggests the possibility that lubiprostone increases mucus secretion.

Lubiprostone ameliorates the cystic fibrosis mouse intestinal phenotype

PubMed Central

2010-01-01

Background Cystic fibrosis (CF) is caused by mutations in the CFTR gene that impair the function of CFTR, a cAMP-regulated anion channel. In the small intestine loss of CFTR function creates a dehydrated, acidic luminal environment which is believed to cause an accumulation of mucus, a phenotype characteristic of CF. CF mice have small intestinal bacterial overgrowth, an altered innate immune response, and impaired intestinal transit. We investigated whether lubiprostone, which can activate the CLC2 Cl- channel, would improve the intestinal phenotype in CF mice. Methods Cftrtm1UNC (CF) and wildtype (WT) littermate mice on the C57BL/6J background were used. Lubiprostone (10 μg/kg-day) was administered by gavage for two weeks. Mucus accumulation was estimated from crypt lumen widths in periodic acid-Schiff base, Alcian blue stained sections. Luminal bacterial load was measured by qPCR for the bacterial 16S gene. Gastric emptying and small intestinal transit in fasted mice were assessed using gavaged rhodamine dextran. Gene expression was evaluated by Affymetrix Mouse430 2.0 microarray and qRT-PCR. Results Crypt width in control CF mice was 700% that of WT mice (P < 0.001). Lubiprostone did not affect WT crypt width but, unexpectedly, increased CF crypt width 22% (P = 0.001). Lubiprostone increased bacterial load in WT mice to 490% of WT control levels (P = 0.008). Conversely, lubiprostone decreased bacterial overgrowth in CF mice by 60% (P = 0.005). Lubiprostone increased gastric emptying at 20 min postgavage in both WT (P < 0.001) and CF mice (P < 0.001). Lubiprostone enhanced small intestinal transit in WT mice (P = 0.024) but not in CF mice (P = 0.377). Among other innate immune markers, expression of mast cell genes was elevated 4-to 40-fold in the CF intestine as compared to WT, and lubiprostone treatment of CF mice decreased expression to WT control levels. Conclusions These results indicate that lubiprostone has some benefits for the CF intestinal phenotype, especially on bacterial overgrowth and the innate immune response. The unexpected observation of increased mucus accumulation in the crypts of lubiprostone-treated CF mice suggests the possibility that lubiprostone increases mucus secretion. PMID:20843337

Geomorphic and hydraulic controls on large-scale riverbank failure on a mixed bedrock-alluvial river system, the River Murray, South Australia: a bathymetric analysis.

NASA Astrophysics Data System (ADS)

De Carli, E.; Hubble, T.

2014-12-01

During the peak of the Millennium Drought (1997-2010) pool-levels in the lower River Murray in South Australia dropped 1.5 metres below sea level, resulting in large-scale mass failure of the alluvial banks. The largest of these failures occurred without signs of prior instability at Long Island Marina whereby a 270 metre length of populated and vegetated riverbank collapsed in a series of rotational failures. Analysis of long-reach bathymetric surveys of the river channel revealed a strong relationship between geomorphic and hydraulic controls on channel width and downstream alluvial failure. As the entrenched channel planform meanders within and encroaches upon its bedrock valley confines the channel width is 'pinched' and decreases by up to half, resulting in a deepening thalweg and channel bed incision. The authors posit that flow and shear velocities increase at these geomorphically controlled 'pinch-points' resulting in complex and variable hydraulic patterns such as erosional scour eddies, which act to scour the toe of the slope over-steepening and destabilising the alluvial margins. Analysis of bathymetric datasets between 2009 and 2014 revealed signs of active incision and erosional scour of the channel bed. This is counter to conceptual models which deem the backwater zone of a river to be one of decelerating flow and thus sediment deposition. Complex and variable flow patterns have been observed in other mixed alluvial-bedrock river systems, and signs of active incision observed in the backwater zone of the Mississippi River, United States. The incision and widening of the lower Murray River suggests the channel is in an erosional phase of channel readjustment which has implications for riverbank collapse on the alluvial margins. The prevention of seawater ingress due to barrage construction at the Murray mouth and Southern Ocean confluence, allowed pool-levels to drop significantly during the Millennium Drought reducing lateral confining support to the over-steepened channel margins triggering large-scale riverbank failure.

I-V Characteristics of a Static Random Access Memory Cell Utilizing Ferroelectric Transistors

NASA Technical Reports Server (NTRS)

Laws, Crystal; Mitchell, Cody; Hunt, Mitchell; Ho, Fat D.; MacLeod, Todd C.

2012-01-01

I-V characteristics for FeFET different than that of MOSFET Ferroelectric layer features hysteresis trend whereas MOSFET behaves same for both increasing and decreasing VGS FeFET I-V characteristics doesn't show dependence on VDS A Transistor with different channel length and width as well as various resistance and input voltages give different results As resistance values increased, the magnitude of the drain current decreased.

Theoretical and experimental investigation into high current hollow cathode arc attachment

NASA Astrophysics Data System (ADS)

Downey, Ryan T.

This research addresses several concerns of the mechanisms controlling performance and lifetime of high-current single-channel-hollow-cathodes, the central electrode and primary life-limiting component in Magnetoplasmadynamic thrusters. Specifically covered are the trends, and the theorized governing mechanisms, seen in the discharge efficiency and power, the size of the plasma attachment to the cathode (the active zone), cathode exit plume plasma density and energy, along with plasma property distributions of the internal plasma column (the IPC) of a single-channel-hollow-cathode. Both experiment and computational modeling were employed in the analysis of the cathodes. Employing Tantalum and Tungsten cathodes (of 2, 6 and 10 mm inner diameter), experiments were conducted to measure the temperature profile of operating cathodes, the width of the active zone, the discharge voltage, power, plasma arc resistance and efficiency, with mass flow rates of 50 to 300 sccm of Argon, and discharge currents of 15 to 50 Amps. Langmuir probing was used to obtain measurements for the electron temperature, plasma density and plasma potential at the cathode exit plane (down stream tip). A computational model was developed to predict the distribution of plasma inside the cathode, based upon experimentally determined boundary conditions. It was determined that the peak cathode temperature is a function of both interior cathode density and discharge current, though the location of the peak temperature is controlled gas density but not discharge current. The active zone width was found to be an increasing function of the discharge current, but a decreasing function of the mass flow rate. The width of the active zone was found to not be controlled by the magnitude of the peak cathode wall temperature. The discharge power consumed per unit of mass throughput is seen as a decreasing function of the mass flow rate, showing the increasing efficiency of the cathode. Finally, this new understanding of the mechanisms of the plasma attachment phenomena of a single-channel-hollow-cathode were extrapolated to the multi-channel-hollow-cathode environment, to explain performance characteristics of these devices seen in previous research.

Riparian Vegetation: Controls on Channel Planform in Noncohesive Beds

NASA Astrophysics Data System (ADS)

Tal, M.; Paola, C.; Gran, K.

2001-12-01

Riparian vegetation has strong consequences for the channel planform and dynamics. An understanding of this role is key to accurate modeling of river systems, and may provide answers to fundamental questions concerning stream dynamics as well as bridge the various approaches to modeling channel evolution. Vegetation on the flood plain works to constrain the flow of the river to a single channel by stabilizing banks and offering resistance to overbank flow. These controls were recently established through a set of controlled experiments at the St. Anthony Falls Laboratory. The runs were designed to determine how addition of vegetation affects channel form and flow dynamics. This was achieved by holding water discharge, sediment discharge, grain size, and slope constant, while making vegetation density the only variable between runs. Plants were grown while water discharge was half its channel-forming value. This work showed that as vegetation density increased there was a decrease in braiding intensity, lateral mobility, and width to depth ratios, and an increase in maximum scour hole depth, and channel relief. While producing braiding experimentally has proven simple, no one has yet produced true dynamic meanders (i.e. high-amplitude bends that grow, cut off, and grow again). Present experimental studies at St. Anthony Falls Laboratory aim to investigate the role of vegetation in the development of a meandering river in otherwise insufficiently cohesive sand that would favor a more stable braided river system. The experiments begin with an unseeded bed into which a straight channel has been carved. Each cycle comprises a period of low discharge during which the bed is seeded with alfalfa seeds. The discharge is raised to a higher discharge only after the plants have grown to a height of about 20 mm (approximately 7 days). The duration of the high-flow stage is such that not more than 10-20% of the channel width is eroded. In addition to offering insight as to the several possible states that a river might be in, the experimental studies are intended to provide an understanding of how vegetation stabilizes single-thread channels, identify the nondimensional parameters that measure the stabilizing effects of vegetation, and realize the role of discharge variation in allowing plant colonization.

Landslides control the spatial and temporal variation of channel width in southern Taiwan: implications for landscape evolution and cascading hazards in steep, tectonically active landscapes

NASA Astrophysics Data System (ADS)

Yanites, B.; Bregy, J. C.; Carlson, G.; Cataldo, K.; Holahan, M.; Johnston, G.; Mitchell, N. A.; Nelson, A.; Valenza, J.; Wanker, M.

2017-12-01

Intense precipitation or seismic events can generate clustered mass movement processes across a landscape. These rare events have significant impacts on the landscape, however, the rarity of such events leads to uncertainty in how these events impact the entire geomorphic system over a range of timescales. Taiwan is a steep, seismically active region and is highly prone to landslide and debris flows, especially when exposed to heavy rainfall events. Typhoon Morakot made landfall in Taiwan in August of 2009, delivering record-breaking rainfall and inducing more than 22,000 landslides in southern Taiwan. The topographic gradient in southern Taiwan leads to spatial variability in landslide susceptibility providing an opportunity to infer the long-term impact of landslides on channel morphology. The availability of pre and post typhoon imagery allows a quantitative reconstruction on the propagating impact of this event on channel width. The pre and post typhoon patterns of channel width to river and hillslope gradients in 20 basins in the study area reveal the importance of cascading hazards from landslides on landscape evolution. Prior to Typhoon Morakot, the river channels in the central part of the study area were about 3-10 times wider than the channels in the south. Aggradation and widening was also a maximum in these basins where hillslope gradients and channel steepness is high. The results further show that the narrowest channels are located where channel steepness is the lowest, an observation inconsistent with a detachment-limited model for river evolution. We infer this pattern is indicative of a strong role of sediment supply, and associated landslide events, on long-term channel evolution. These findings have implications across a range of spatial and temporal scales including understanding the cascade of hazards in steep landscapes and geomorphic interpretation of channel morphology.

GIS technology for spatiotemporal measurements of gully channel width evolution

USDA-ARS?s Scientific Manuscript database

Field observations of gully evolution in active croplands have often revealed the presence of a less erodible soil layer that is typically associated with tillage practices (i.e. plowpan). This more erosion-resistant layer limits channel incision forcing the gully channel to expand laterally through...

Research and development on performance models of thermal imaging systems

NASA Astrophysics Data System (ADS)

Wang, Ji-hui; Jin, Wei-qi; Wang, Xia; Cheng, Yi-nan

2009-07-01

Traditional ACQUIRE models perform the discrimination tasks of detection (target orientation, recognition and identification) for military target based upon minimum resolvable temperature difference (MRTD) and Johnson criteria for thermal imaging systems (TIS). Johnson criteria is generally pessimistic for performance predict of sampled imager with the development of focal plane array (FPA) detectors and digital image process technology. Triangle orientation discrimination threshold (TOD) model, minimum temperature difference perceived (MTDP)/ thermal range model (TRM3) Model and target task performance (TTP) metric have been developed to predict the performance of sampled imager, especially TTP metric can provides better accuracy than the Johnson criteria. In this paper, the performance models above are described; channel width metrics have been presented to describe the synthesis performance including modulate translate function (MTF) channel width for high signal noise to ration (SNR) optoelectronic imaging systems and MRTD channel width for low SNR TIS; the under resolvable questions for performance assessment of TIS are indicated; last, the development direction of performance models for TIS are discussed.

Triangle mechanisms in the build up and decay of the N*(1875 )

NASA Astrophysics Data System (ADS)

Samart, Daris; Liang, Wei-Hong; Oset, Eulogio

2017-09-01

We studied the N*(1875 ) (3 /2-) resonance with a multichannel unitary scheme, considering the Δ π and Σ*K , with their interaction extracted from chiral Lagrangians, and then added two more channels, the N*(1535 ) π and N σ , which proceed via triangle diagrams involving the Σ*K and Δ π respectively in the intermediate states. The triangle diagram in the N*(1535 ) π case develops a singularity at the same energy as the resonance mass. We determined the couplings of the resonance to the different channels and the partial decay widths. We found a very large decay width to Σ*K , and also observed that, due to interference with other terms, the N σ channel has an important role in the π π mass distributions at low invariant masses, leading to an apparently large N σ decay width. We discuss justifying the convenience of an experimental reanalysis of this resonance, in light of the findings of the paper, using multichannel unitary schemes.

The erosion of streamlined islands, longitudinal grooves and scour marks: Implications to the origin of the Martian outflow channels

NASA Technical Reports Server (NTRS)

Komar, P. D.

1984-01-01

The diversity of proposed origins for large Martian outflow channels results from the differing interpretations given to the landforms associated with the outflow channels. In an attempt to help limit the possible mechanisms of channel erosion, detailed studies of three of the channel features were done; the streamlined islands, longitudinal grooves and scour marks. This examination involved a comparison of the martian streamlined islands with various streamlined landforms on Earth including those found in the Channel Scabland in large rivers, glacial drumlins, and desert yardangs. The comparisons included statistical analyses of the landform lengths versus widths and positions of maximum width, and an examination of the degree of shape agreement with the geometric lemniscate which was in turn demonstrated to correspond closely with true airfoil shapes. The analyses showed that the shapes of the martian islands correspond closely to the streamlined islands in rivers and the Channel Scabland land. Drumlins show a much smaller correlation. Erosional rock islands formed by glaciers are very much different in shape.

On the origin of the phase-space diffusion limit in (dis)ordered protein aggregation

NASA Astrophysics Data System (ADS)

Gadomski, A.; Siódmiak, J.; Santamaría-Holek, I.

2013-08-01

Derivation of a phase-space diffusion limit (D-L) allows to obtain a useful formula for a characteristic width of the macroion-channeling filter, controlling model (dis)ordered protein aggregations in a non-ideal aqueous solution. The channel’s width is estimated at the order of an inner half-width of the Stern-type double layer circumventing the growing object and depends in turn on an interplay of the local thermal and electrostatic conditions. The interfacial channeling effect manifests at the edge of biomolecular hydration-duration dependent (non)Markovianity of the system. The interface vs. solution aggregation late-time dynamics are discussed in such local (non)isothermal context with the aim to suggest their experimental assessment.

Feedbacks Between Channel Adjustment, Sediment Calibre and Landscape Dynamics in Tectonically Perturbed Landscapes (Invited)

NASA Astrophysics Data System (ADS)

Attal, M.; Cowie, P. A.; Whittaker, A. C.; Tucker, G. E.; Mudd, S. M.; Hurst, M. D.

2010-12-01

Knowledge of the coupling between channel geometry and sediment input to rivers is central to understanding the mechanisms and timescales over which landscapes respond to a tectonic perturbation. Here, we document changes to channel geometry and sediment calibre in catchments experiencing a well-constrained increase in relative uplift rate in the Central Apennines (Italy) and the Sierra Nevada (California). In both landscapes, channels and hillslopes steepen and knickpoints propagate upstream through the catchments, leading to the formation of a break in both hillslope and channel gradient that separates the steepened landscape from lower relief topography which has not yet responded to the change in uplift rate. Downstream of this break in slope, channels narrow markedly as river gradient increases. In addition, they are supplied with coarser sediment from the steepened hillslopes, in particular when sediment is supplied via landslides and debris fans. In Italy, channel narrowing can be explained using the equation proposed by Finnegan et al. [2005]: W = kQ3/8S-3/16, where W is channel width, k is a constant, Q is river discharge and S is channel slope. However, to model our field data, the prefactor k must be strongly dependent on uplift rate: the higher the uplift rate, the smaller the prefactor k. Using the Channel-Hillslope Integrated Landscape Development (CHILD) model, we show that the location of the main break in slope along the river profiles in Italy (in terms of height and along stream distance) can be fitted using a detachment-limited model with dynamic channel adjustment (equation above), k dependent on uplift rate and a threshold for erosion. A threshold corresponding to the shear stress required to entrain the median grain size of the sediment along the steepened reaches of the channels best fits the data. Our modelling results show that the response time of the landscape in this setting is strongly dependent on relative uplift rate, since knickpoint retreat rate in the detachment-limited model is a function of channel width and that the higher the relative uplift rate, the narrower the river. In a catchment uplifted at 1.5 mm/yr, knickpoint retreat rate can be up to 3 times higher than in a catchment uplifted at 0.25 mm/yr. This result is in agreement with measurements of knickpoint retreat rates using field data in the Apennines [Whittaker et al., 2008]. Steepened hillslopes along the rapidly incising Feather River, Sierra Nevada, California

Numerical investigation of interfacial transport resistance due to water droplets in proton exchange membrane fuel cell air channels

NASA Astrophysics Data System (ADS)

Koz, Mustafa; Kandlikar, Satish G.

2013-12-01

Oxygen transport resistance at the air flow channel and gas diffusion layer (GDL) interface is needed in modelling the performance of a proton exchange membrane fuel cell (PEMFC). This resistance is expressed through the non-dimensional Sherwood number (Sh). The effect of the presence of a droplet on Sh is studied numerically in an isolated air flow channel using a commercially available package, COMSOL Multiphysics®. A droplet is represented as a solid obstruction placed on the GDL-channel interface and centred along the channel width. The effect of a single droplet is first studied for a range of superficial mean air velocities and droplet sizes. Secondly, the effect of droplet spacing on Sh is studied through simulations of two consecutive droplets. Lastly, multiple droplets in a row are studied as a more representative case of a PEMFC air flow channel. The results show that the droplets significantly increase Sh above the fully developed value in the wake region. This enhancement increases with the number of droplets, droplet size, and superficial mean air velocity. Moreover, the analogy between mass and heat transfer is investigated by comparing Sh to the equivalent Nusselt number.

Analysis of Factors Limiting Bacterial Growth in PDMS Mother Machine Devices.

PubMed

Yang, Da; Jennings, Anna D; Borrego, Evalynn; Retterer, Scott T; Männik, Jaan

2018-01-01

The microfluidic mother machine platform has attracted much interest for its potential in studies of bacterial physiology, cellular organization, and cell mechanics. Despite numerous experiments and development of dedicated analysis software, differences in bacterial growth and morphology in narrow mother machine channels compared to typical liquid media conditions have not been systematically characterized. Here we determine changes in E. coli growth rates and cell dimensions in different sized dead-end microfluidic channels using high resolution optical microscopy. We find that E. coli adapt to the confined channel environment by becoming narrower and longer compared to the same strain grown in liquid culture. Cell dimensions decrease as the channel length increases and width decreases. These changes are accompanied by increases in doubling times in agreement with the universal growth law. In channels 100 μm and longer, cell doublings can completely stop as a result of frictional forces that oppose cell elongation. Before complete cessation of elongation, mechanical stresses lead to substantial deformation of cells and changes in their morphology. Our work shows that mechanical forces rather than nutrient limitation are the main growth limiting factor for bacterial growth in long and narrow channels.

Analysis of Factors Limiting Bacterial Growth in PDMS Mother Machine Devices

DOE PAGES

Yang, Da; Jennings, Anna D.; Borrego, Evalynn; ...

2018-05-01

The microfluidic mother machine platform has attracted much interest for its potential in studies of bacterial physiology, cellular organization, and cell mechanics. Despite numerous experiments and development of dedicated analysis software, differences in bacterial growth and morphology in narrow mother machine channels compared to typical liquid media conditions have not been systematically characterized. Here we determine changes in E. coli growth rates and cell dimensions in different sized dead-end microfluidic channels using high resolution optical microscopy. We find that E. coli adapt to the confined channel environment by becoming narrower and longer compared to the same strain grown in liquidmore » culture. Cell dimensions decrease as the channel length increases and width decreases. These changes are accompanied by increases in doubling times in agreement with the universal growth law. In channels 100 μm and longer, cell doublings can completely stop as a result of frictional forces that oppose cell elongation. Before complete cessation of elongation, mechanical stresses lead to substantial deformation of cells and changes in their morphology. Lastly, our work shows that mechanical forces rather than nutrient limitation are the main growth limiting factor for bacterial growth in long and narrow channels.« less

Analysis of Factors Limiting Bacterial Growth in PDMS Mother Machine Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Da; Jennings, Anna D.; Borrego, Evalynn

The microfluidic mother machine platform has attracted much interest for its potential in studies of bacterial physiology, cellular organization, and cell mechanics. Despite numerous experiments and development of dedicated analysis software, differences in bacterial growth and morphology in narrow mother machine channels compared to typical liquid media conditions have not been systematically characterized. Here we determine changes in E. coli growth rates and cell dimensions in different sized dead-end microfluidic channels using high resolution optical microscopy. We find that E. coli adapt to the confined channel environment by becoming narrower and longer compared to the same strain grown in liquidmore » culture. Cell dimensions decrease as the channel length increases and width decreases. These changes are accompanied by increases in doubling times in agreement with the universal growth law. In channels 100 μm and longer, cell doublings can completely stop as a result of frictional forces that oppose cell elongation. Before complete cessation of elongation, mechanical stresses lead to substantial deformation of cells and changes in their morphology. Lastly, our work shows that mechanical forces rather than nutrient limitation are the main growth limiting factor for bacterial growth in long and narrow channels.« less

Enhanced Small Scale Heat Transfer in Rectangular Channels using Autonomous, Aero-Elastically Fluttering Reeds

NASA Astrophysics Data System (ADS)

Jha, Sourabh; Crittenden, Thomas; Glezer, Ari

2017-11-01

The limits of low Reynolds number forced convection heat transport within rectangular, mm-scale channels that model segments of air-cooled heat sinks are overcome by the deliberate formation of unsteady small-scale vortical motions that are induced by autonomous aero-elastic fluttering of cantilevered planar thin-film reeds. The coupled flow-structure interactions between the fluttering reeds and the embedding channel flow and the formation and evolution of the induced unsteady small-scale vortical motions are explored using video imaging and PIV. Concave/convex undulations of the reed's surface that are bounded by the channel's walls lead to the formation and advection of cells of vorticity concentration and ultimately to alternate shedding of spanwise CW and CCW vortices. These vortices scale with the channel height, and result in increased turbulent kinetic energy and enhanced dissipation that persist far downstream from the reed and are reminiscent of a turbulent flow at significantly higher Reynolds numbers (e.g., at Re = 800, TKE increases by 86% ,40 channel widths downstream of reed tip). These small-scale motions lead to strong enhancement in heat transfer that increases with Re (e.g., at Re = 1,000 and 14,000, Nu increases by 36% and 91%, respectively). The utility of this approach is demonstrated in improving the thermal performance of low-Re heat sinks in air-cooled condensers of thermoelectric power plants. NSF-EPRI.

Design and evaluation of a Dean vortex-based micromixer.

PubMed

Howell, Peter B; Mott, David R; Golden, Joel P; Ligler, Frances S

2004-12-01

A mixer, based on the Dean vortex, is fabricated and tested in an on-chip format. When fluid is directed around a curve under pressure driven flow, the high velocity streams in the center of the channel experience a greater centripetal force and so are deflected outward. This creates a pair of counter-rotating vortices moving fluid toward the inner wall at the top and bottom of the channel and toward the outer wall in the center. For the geometries studied, the vortices were first seen at Reynolds numbers between 1 and 10 and became stronger as the flow velocity is increased. Vortex formation was monitored in channels with depth/width ratios of 0.5, 1.0, and 2.0. The lowest aspect ratio strongly suppressed vortex formation. Increasing the aspect ratio above 1 appeared to provide improved mixing. This design has the advantages of easy fabrication and low surface area.

Internal and external radiative widths in the combined R -matrix and potential-model formalism

NASA Astrophysics Data System (ADS)

Mukhamedzhanov, A. M.; Shubhchintak, Bertulani, C. A.; Hao, T. V. Nhan

2017-02-01

By using the R -matrix approach we calculate the radiative width for a resonance decaying to a bound state through electric-dipole E 1 transitions. The total radiative width is determined by the interference of the nuclear internal and external radiative width amplitudes. For a given channel radius the external radiative width amplitude is model independent and is determined by the asymptotic normalization coefficient (ANC) of the bound state to which the resonance decays. It also depends on the partial resonance width. To calculate the internal radiative width amplitude we show that a single-particle-potential model is appropriate. We compare our results with a few experimental data.

Refernce Conditions for Streams in the Grand Prairie Natural Division of Illinois

NASA Astrophysics Data System (ADS)

Sangunett, B.; Dewalt, R.

2005-05-01

As part of the Critical Trends Assessment Program (CTAP) of the Illinois Department of Natural Resources (IDNR), 12 potential reference quality stream sites in the Grand Prairie Natural Division were evaluated in May 2004. This agriculturally dominated region, located in east central Illinois, is the most highly modified in the state. The quality of these sites was assessed using a modified Hilsenhoff Biotic Index and species richness of Ephemeroptera, Plecoptera, and Trichoptera (EPT) insect orders and a 12 parameter Habitat Quality Index (HQI). Illinois EPA high quality fish stations, Illinois Natural History Survey insect collection data, and best professional knowledge were used to choose which streams to evaluate. For analysis, reference quality streams were compared to 37 randomly selected meandering streams and 26 randomly selected channelized streams which were assessed by CTAP between 1997 and 2001. The results showed that the reference streams exceeded both taxa richness and habitat quality of randomly selected streams in the region. Both random meandering sites and reference quality sites increased in taxa richness and HQI as stream width increased. Randomly selected channelized streams had about the same taxa richness and HQI regardless of width.

NUTRIENT UPTAKE LENGTH, CHANNEL STRUCTURE, AND TRANSIENT STORAGE IN STREAMS DRAINING HARVESTED AND OLD GROWTH WATERSHEDS

EPA Science Inventory

Channel structure and transient storage were correlated with nutrient uptake length in streams draining old-growth and harvested watersheds in the Cascade Mountains of Oregon, and the redwood forests of northwestern California. Channel width and riparian canopy were measured at 1...

The role of large predators in maintaining riparian plant communities and river morphology

NASA Astrophysics Data System (ADS)

Beschta, Robert L.; Ripple, William J.

2012-07-01

Studies assessing the potential for large predators to affect, via trophic cascades, the dynamics of riparian plant communities and the morphology of river channels have been largely absent in the scientific literature. Herein, we consider the results of recent studies involving three national parks in the western United States: Yellowstone, Olympic, and Zion. Within each park, key large predators were extirpated or displaced in the early 1900s and subsequent browsing pressure by native ungulates initiated long-term declines in recruitment (i.e., growth of seedlings/sprouts into tall saplings and trees) of palatable woody species and impairment of other resources. Channel responses to browsing-suppressed riparian vegetation included increased widths of active channels via accelerated bank erosion, erosion of floodplains and erraces, increased area of unvegetated alluvium, channel incision, and increased braiding. A reduced frequency of overbank flows indicated these rivers have become increasingly disconnected from historical floodplains because of channel widening/incision. Results from Zion National Park also identified major biodiversity affects (e.g., reduced abundance of plant and animal species). Although these studies were conducted in national parks, results may have implications concerning riparian plant communities, biodiversity, and channel morphology for streams and rivers draining other public lands in the western US. It is on these lands that native and introduced ungulates have often heavily utilized riparian areas, largely in the absence of key predators, with significant consequences to plant communities and channels.

Cottonwood Tree Rings and Climate in Western North America

NASA Astrophysics Data System (ADS)

Friedman, J. M.; Edmondson, J.; Griffin, E. R.; Meko, D. M.; Merigliano, M. F.; Scott, J. A.; Scott, M. L.; Touchan, R.

2012-12-01

In dry landscapes of interior western USA, cottonwood (Populus spp.) seedling establishment often occurs only close to river channels after floods. Where winter is sufficiently cold, cottonwoods also have distinct annual rings and can live up to 370 years, allowing us to reconstruct the long-term history of river flows and channel locations. We have analyzed the annual rate of cottonwood establishment along streams in Montana, Wyoming, Colorado, North Dakota and Idaho. Because the trees germinate next to the river, establishment rates are strongly correlated with the rate of channel migration driven by floods. Along large rivers dominated by snowmelt from the mountains, interannual variation in peak flows and cottonwood establishment is small, and century-scale variation driven by climate change is apparent. The upper Snake, Yellowstone and Green rivers all show a strong decrease in cottonwood establishment beginning in the late 1800s and continuing to the present, indicating a decrease in peak flows prior to flow regulation by large dams. This is consistent with published tree-ring studies of montane conifers showing decreases in snowpack at the same time scale. In contrast, beginning in the late 1800s cottonwood ring widths along the Little Missouri River, North Dakota show an increase in annual growth that continues into the present. Because annual growth is strongly correlated with April-July flows (r=0.69) the ring-width data suggest an increase in April-July flows at the same time tree establishment dates suggest a decrease in peak flows. These results may be reconciled by the hypothesis that increases in low temperatures have decreased snowpack while lengthening the growing season.

Regionalized equations for bankfull-discharge and channel characteristics of streams in New York State—Hydrologic Region 6 in the Southern Tier of New York

USGS Publications Warehouse

Mulvihill, Christiane I.; Ernst, Anne G.; Baldigo, Barry P.

2005-01-01

Equations that relate bankfull discharge and channel characteristics (width, depth, and cross-sectional area) to drainage-area size at gaged sites are needed to define bankfull discharge and channel dimensions at ungaged sites and to provide information for watershed assessments, stream-channel classification, and the design of stream-restoration projects. Such equations are most accurate if derived from streams within an area of uniform hydrologic, climatic, and physiographic conditions and applied only within that region. In New York State, eight hydrologic regions were previously defined on the basis of similar high-flow (flood) characteristics. This report presents drainage areas and associated bankfull characteristics (discharge and channel dimensions) for surveyed streams in southwestern New York (Region 6).Stream-survey data and discharge records from 11 active (currently gaged) sites and 3 inactive (discontinued) sites were used in regression analyses to relate bankfull discharge and bankfull channel width, depth, and cross-sectional area to the size of the drainage area. The resulting equations are:(1) bankfull discharge, in cubic feet per second = 48.0*(drainage area, in square miles)0.842;(2) bankfull channel width, in feet = 16.9*(drainage area, in square miles)0.419;(3) bankfull channel depth, in feet = 1.04*(drainage area, in square miles)0.244; and(4) bankfull channel cross-sectional area, in square feet = 17.6*(drainage area, in square miles)0.662.The coefficient of determination (R2) for these four equations were 0.90, 0.79, 0.64, and 0.89, respectively. The high correlation coefficients for bankfull discharge and cross-sectional area indicate that much of the variation in these variables is explained by the size of the drainage area. The smaller correlation coefficients for bankfull channel width and depth indicate that other factors also affect these relations. Recurrence intervals for the estimated bankfull discharge of each stream ranged from 1.01 to 2.35 years; the mean recurrence interval was 1.54 years. The 14 surveyed streams were classified by Rosgen stream type; most were C-type reaches, with occasional B-type reaches. The Region 6 equation (curve) for bankfull discharge was compared with equations previously developed for four other large areas in New York State and southeastern Pennsylvania. The differences among results indicate that, although the equations need to be refined by region before being applied by water-resources managers to local planning and design efforts, similar regions have similar relations between bankfull discharge and channel characteristics.

How does floodplain width affect floodplain river ecology? A preliminary exploration using simulations

NASA Astrophysics Data System (ADS)

Power, Mary E.; Parker, Gary; Dietrich, William E.; Sun, Adrian

1995-09-01

Hydraulic food chain models allow us to explore the linkages of river discharge regimes and river-floodplain morphology to the structure and dynamics of modeled food webs. Physical conditions (e.g. depth, width, velocity) that vary with river discharge affect the performance (birth, growth, feeding, movement, or death rates) of organisms or trophic groups. Their performances in turn affect their impacts on food webs and ecosystems in channel and floodplain habitats. Here we explore the impact of floodplain width (modeled as 1 ×, 10× and 40× the channel width) on a food web with two energy sources (detritus and vegetation), invertebrates that consume these, a size structured fish population which consumes invertebrates and in which larger fish cannibalize small fish, and birds which feed on large fish. Hydraulic linkages to trophic dynamics are assumed to be mediated in three ways: birds feed efficiently only in shallow water; plant carrying capacity varies non-linearly with water velocity, and mobile and drifting organisms are diluted and concentrated with spillover of river discharge to the floodplain, and its reconfinement to the channel. Aspects of this model are based on field observations of Junk and Bailey from the Amazon, of Sparks from the Mississippi, and on our observations of the Fly River in Papua New Guinea. The model produced several counter-intuitive results. Biomass of invertebrates and fish increased with floodplain width, but much more rapidly from 1 × to 10 × floodplains than from 10 × to 40 × floodplains. For birds, maximum biomass occurred on the 10× floodplain. Initially high bird biomass on the 40 × floodplain declined to extinction over time, because although favorable fishing conditions (shallow water) were most prolonged on the widest floodplain, this advantage was more than offset by the greater dilution of prey after spillover. Bird predation on large fish sometimes increased their biomass, by reducing cannibalism and thereby increasing the abundance of small fish available to grow into the larger size class. Sensitivity analyses indicated that model results were relatively robust to variation in parameter values that we chose, but much more exploration and calibration with field data are needed before we know how specific our results are to the structure and other assumptions of this model. We share with others the opinion that progress towards understanding complex dynamic systems like floodplain river ecosystems requires frequent feedback between modeling and field observations and experimentation. This understanding is crucial for river management and restoration. Organisms in real rivers have adapted to track and quickly exploit favorable conditions, and to avoid or endure adverse conditions. It is when we engineer away this environmental variability that we threaten the long term persistence of river-adapted biota.

Distinctive channel geometry and riparian vegetation: A geomorphic classification for arid ephemeral streams

NASA Astrophysics Data System (ADS)

Sutfin, N.; Shaw, J. R.; Wohl, E. E.; Cooper, D.

2012-12-01

Interactions between hydrology, channel form, and riparian vegetation along arid ephemeral streams are not thoroughly understood and current stream classifications do not adequately represent variability in channel geometry and associated riparian communities. Relatively infrequent hydrologic disturbances in dryland environments are responsible for creation and maintenance of channel form that supports riparian communities. To investigate the influence of channel characteristics on riparian vegetation in the arid southwestern United States, we develop a geomorphic classification for arid ephemeral streams based on the degree of confinement and the composition of confining material that provide constraints on available moisture. Our conceptual model includes five stream types: 1) bedrock channels entirely confined by exposed bedrock and devoid of persistent alluvium; 2) bedrock with alluvium channels at least partially confined by bedrock but containing enough alluvium to create bedforms that persist through time; 3) incised alluvium channels bound only by unconsolidated alluvial material into which they are incised; 4) braided washes that exhibit multi-thread, braided characteristics regardless of the composition of confining material; and 5) piedmont headwater 0-2nd order streams (Strahler) confined only by unconsolidated alluvium and which initiate as secondary channels on piedmont surfaces. Eighty-six study reaches representing the five stream types were surveyed on the U.S. Army Yuma Proving Ground in the Sonoran Desert of southwestern Arizona. Non-parametric multivariate analysis of variance (PERMANOVA) indicates significant differences between the five stream types with regards to channel geometry (i.e., stream gradient, width-to-depth ratio, the ratio between valley width and channel width (Wv/Wc), shear stress, and unit stream power) and riparian vegetation (i.e., presence and canopy coverage by species, canopy stratum, and life form). Discriminant analysis of the physical driving variables is being conducted to produce a model that predicts stream type and resulting riparian vegetation communities based on channel geometry. This model will be tested on a separate set of 15 study reaches surveyed on the Barry M. Goldwater Air Force Range in southern Arizona. The resulting classification will provide a basis for examining relationships between hydrology, channel and watershed characteristics, riparian vegetation and ecosystem sensitivity of ephemeral streams in arid regions of the American Southwest.

Large-scale erosional and depositional features of the Channeled Scabland

NASA Technical Reports Server (NTRS)

Baker, V. R.

1978-01-01

The channeled scabland is a great anastomosing complex of highly overfit stand channels eroded into the basalt bedrock and overlying sediments of the Columbia Plateau. Both the erosional and depositional bed forms in these channels are described according to a simple hierarchical classification. The catastrophic flood flows produced macroforms (scale controlled by channel width) through the erosion of rock and sediment and by deposition (bars). Mesoforms (scale controlled by channel depth) are also erosional and depositional.

Inertial migration of deformable droplets in a microchannel

NASA Astrophysics Data System (ADS)

Chen, Xiaodong; Xue, Chundong; Zhang, Li; Hu, Guoqing; Jiang, Xingyu; Sun, Jiashu

2014-11-01

The microfluidic inertial effect is an effective way of focusing and sorting droplets suspended in a carrier fluid in microchannels. To understand the flow dynamics of microscale droplet migration, we conduct numerical simulations on the droplet motion and deformation in a straight microchannel. The results are compared with preliminary experiments and theoretical analysis. In contrast to most existing literature, the present simulations are three-dimensional and full length in the streamwise direction and consider the confinement effects for a rectangular cross section. To thoroughly examine the effect of the velocity distribution, the release positions of single droplets are varied in a quarter of the channel cross section based on the geometrical symmetries. The migration dynamics and equilibrium positions of the droplets are obtained for different fluid velocities and droplet sizes. Droplets with diameters larger than half of the channel height migrate to the centerline in the height direction and two equilibrium positions are observed between the centerline and the wall in the width direction. In addition to the well-known Segré-Silberberg equilibrium positions, new equilibrium positions closer to the centerline are observed. This finding is validated by preliminary experiments that are designed to introduce droplets at different initial lateral positions. Small droplets also migrate to two equilibrium positions in the quarter of the channel cross section, but the coordinates in the width direction are between the centerline and the wall. The equilibrium positions move toward the centerlines with increasing Reynolds number due to increasing deformations of the droplets. The distributions of the lift forces, angular velocities, and the deformation parameters of droplets along the two confinement direction are investigated in detail. Comparisons are made with theoretical predictions to determine the fundamentals of droplet migration in microchannels. In addition, existence of the inner equilibrium position is linked to the quartic velocity distribution in the width direction through a simple model for the slip angular velocities of droplets.

Surface viscosity effects on the motion of self-propelling boat in a channel

NASA Astrophysics Data System (ADS)

Aliperio, M. G.; Nolan Confesor, Mark

2015-06-01

Self-propelled droplets have been conceived as simple chemical toy models to mimic motile biological samples such as bacteria. The motion of these droplets is believe to be due to the surface tension gradient in the boundary of the droplet. We performed experiments to look at the effect of varying the medium viscosity to the speed of a circular boat that was soaked in Pentanol. We found that the boats undergo oscillatory type of motion inside a channel. Moreover we found the maximum speed of the boat is independent on the viscosity of the medium. On the other a time scale describing the width of the velocity profile of the boat was found to increase with increasing viscosity.

Nonlinear pressure-flow relationships for passive microfluidic valves.

PubMed

Seker, Erkin; Leslie, Daniel C; Haj-Hariri, Hossein; Landers, James P; Utz, Marcel; Begley, Matthew R

2009-09-21

An analytical solution is presented for the nonlinear pressure-flow relationship of deformable passive valves, which are formed by bonding a deformable film over etched channels separated by a weir. A fluidic pathway connecting the channels is opened when the upstream pressure creates a tunnel along a predefined narrow strip where the film is not bonded to the weir. When the width of the strip is comparable to the inlet channel width, the predicted closed-form pressure-flow rate relationship is in excellent agreement with experiments, which determine pressures by measuring film deflections for prescribed flow rates. The validated closed-form models involve no fitting parameters, and provide the foundation to design passive diodes with specific nonlinear pressure-flow characteristics.

Bounding the Higgs boson width through interferometry.

PubMed

Dixon, Lance J; Li, Ye

2013-09-13

We study the change in the diphoton-invariant-mass distribution for Higgs boson decays to two photons, due to interference between the Higgs resonance in gluon fusion and the continuum background amplitude for gg→γγ. Previously, the apparent Higgs mass was found to shift by around 100 MeV in the standard model in the leading-order approximation, which may potentially be experimentally observable. We compute the next-to-leading-order QCD corrections to the apparent mass shift, which reduce it by about 40%. The apparent mass shift may provide a way to measure, or at least bound, the Higgs boson width at the Large Hadron Collider through "interferometry." We investigate how the shift depends on the Higgs width, in a model that maintains constant Higgs boson signal yields. At Higgs widths above 30 MeV, the mass shift is over 200 MeV and increases with the square root of the width. The apparent mass shift could be measured by comparing with the ZZ* channel, where the shift is much smaller. It might be possible to measure the shift more accurately by exploiting its strong dependence on the Higgs transverse momentum.

A Novel Joint Problem of Routing, Scheduling, and Variable-Width Channel Allocation in WMNs

PubMed Central

Liu, Wan-Yu; Chou, Chun-Hung

2014-01-01

This paper investigates a novel joint problem of routing, scheduling, and channel allocation for single-radio multichannel wireless mesh networks in which multiple channel widths can be adjusted dynamically through a new software technology so that more concurrent transmissions and suppressed overlapping channel interference can be achieved. Although the previous works have studied this joint problem, their linear programming models for the problem were not incorporated with some delicate constraints. As a result, this paper first constructs a linear programming model with more practical concerns and then proposes a simulated annealing approach with a novel encoding mechanism, in which the configurations of multiple time slots are devised to characterize the dynamic transmission process. Experimental results show that our approach can find the same or similar solutions as the optimal solutions for smaller-scale problems and can efficiently find good-quality solutions for a variety of larger-scale problems. PMID:24982990

Long-Term Stage, Stage-Residual, and Width Data for Streams in the Piedmont Physiographic Region, Georgia

USGS Publications Warehouse

Riley, Jeffrey W.; Jacobson, Robert B.

2009-01-01

This report presents the data used to assess geomorphic adjustment of streams over time and to changing land-use conditions. Thirty-seven U.S. Geological Survey streamgages were selected within the Piedmont physiographic region of Georgia. Width, depth, stage, and discharge data from these streams were analyzed to assess channel stability and determine if systematic adjustments of channel morphology could be related to time or land use and land cover. Residual analyses of stage-discharge data were used to infer channel stability, which could then be used as an indicator of habitat stability. Streamgages, representing a gradient of urbanization, were selected to test hypotheses regarding stream stability and adjustment to urban conditions. Results indicate that 14 sites exhibited long-term channel stability, 11 were degrading, 6 were aggrading, and 6 showed variability in response over the study period.

Transverse mixing of simulated piscicides in small montane streams

USGS Publications Warehouse

Brown, Peter J.; Ard, Jenifer L.; Zale, Alexander V.

2012-01-01

Thorough mixing of piscicides into receiving waters is important for efficient and effective fish eradication. However, no guidance exists for the placement of drip stations with respect to mixing. Salt (NaCl) was used as a tracer to measure the mixing rates of center versus edge applications in riffle–pool, straight, and meandering sections of montane streams. The tracer was applied at either the center or the edge of a channel and measured with a conductivity meter across a downstream grid to determine the distances at which transverse mixing was complete. No advantage was accrued by applying piscicides in different types of channels because transverse mixing distance did not differ among them. However, mixing distance was significantly shorter at center applications. Chemicals entering a stream at the center of the channel mixed thoroughly within 10 stream widths, whereas chemicals entering a stream channel at the edge mixed thoroughly within 20 stream widths.

Design and evaluation of hydraulic baffled-channel PAC contactor for taste and odor removal from drinking water supplies.

PubMed

Kim, Young-Il; Bae, Byung-Uk

2007-05-01

Based on the concept of hydraulic flocculator, a baffled-channel powdered activated carbon (PAC) contactor, placed before the rapid-mixing basin, was designed and evaluated for removal of taste and odor (T&O) in drinking water. PAC adsorption kinetic tests for raw water samples were conducted for selection of design parameters related to contact time and degree of mixing. Within the tested range of velocity gradient (G) from 18 to 83s(-1), mixing had a relatively minor effect on the adsorption kinetics of the PAC. The hydrodynamic characteristics of the pilot-scale horizontally and vertically baffled-channel PAC contactor were investigated by tracer tests. It was found that the plug flow fractions of vertically baffled-channel PAC contactor (vBPC) were higher than those of the horizontally baffled-channel PAC contactor (hBPC) for the same bend width or bend height. However, the hBPC seems to be more appropriate than the vBPC in terms of construction and maintenance. The geosmin and MIB removal rate increased with the number of baffles, PAC dose and contact time increased regardless of bend width in the pilot-scale hBPC. The pair of full-scale hBPCs at Pohang water treatment plant, having a design capacity of 6.5x10(4)m(3)/d with 20min of hydraulic retention time with a safety factor of 2, was designed based on lab- and pilot-scale experimental results. Under a velocity gradient of 20s(-1), the number of baffles to be installed was calculated to be 20 with a space of about 2m between each baffle, resulting in a hydraulic head loss through the contactor of about 0.056m. The successful application of hBPC for T&O removal from drinking water supplies should provide momentum for developing more effective treatment methods.

Streamflow and Topographic Characteristics of the Platte River near Grand Island, Nebraska, 1938-2007

USGS Publications Warehouse

Woodward, Brenda K.

2008-01-01

The central Platte River is a dynamic, braided, sand-bed river located near Grand Island, Nebraska. An understanding of the Platte River channel characteristics, hydrologic flow patterns, and geomorphic conditions is important for the operation and management of water resources by the City of Grand Island. The north channel of the Platte River flows within 1 mile of the municipal well field, and its surface-water flow recharges the underlying aquifer, which serves as a water source for the city. Recharge from the north channel helps minimize the flow of contaminated ground water from the north of the channel towards the well field. In recent years the river channels have experienced no-flow conditions for extended periods during the summer and fall seasons, and it has been observed that no-flow conditions in the north channel often persist after streamflow has returned to the other three channels. This potentially allows more contaminated ground water to move toward the municipal well field each year, and has caused resource managers to ask whether human disturbances or natural geomorphic change have contributed to the increased frequency of no-flow conditions in the north channel. Analyses of aerial photography, channel surveys, Light Detection and Ranging data, discharge measurements, and historical land surveys were used to understand the past and present dynamics of the four channels of the Platte River near Grand Island and to detect changes with time. Results indicate that some minor changes have occurred in the channels. Changes in bed elevation, channel location, and width were minimal when compared using historical information. Changes in discharge distribution among channels indicate that low- and no-flow conditions in the north channel may be attributed to the small changes in channel characteristics or small elevation differences, along with recent reductions in total streamflow within the Platte River near Grand Island, or to factors not measured in this study, such as increased channel roughness from increased vegetation within the channel.

Regionalized equations for bankfull-discharge and channel characteristics of streams in New York State—Hydrologic Region 7 in western New York

USGS Publications Warehouse

Mulvihill, Christiane I.; Ernst, Anne G.; Baldigo, Barry P.

2006-01-01

Computation of bankfull discharge and channel dimensions (width, depth, and cross-sectional area) at ungaged sites requires equations that relate bankfull discharge and channel dimensions to drainage-area at gaged sites. Bankfull-channel information commonly is needed for watershed assessments, stream channel classification, and the design of stream-restoration projects. Such equations are most accurate if they are derived on the basis of data from streams within a region of uniform hydrologic, climatic, and physiographic conditions and applied only within that region. New York State contains eight hydrologic regions that were previously delineated on the basis of high-flow (flood) characteristics. This report presents drainage areas and associated bankfull characteristics (discharge and channel dimensions) for surveyed streams in western New York (Region 7).Stream-survey data and discharge records from seven active and three inactive USGS streamflow-gaging stations were used in regression analyses to relate drainage area to bankfull discharge and to bankfull channel width, depth, and cross-sectional area. The resulting equations are:(1) bankfull discharge, in cubic feet per second = 37.1*(drainage area, in square miles)0.765;(2) bankfull channel width, in feet = 10.8*(drainage area, in square miles)0.458;(3) bankfull channel depth, in feet = 1.47*(drainage area, in square miles)0.199; and(4) bankfull channel cross-sectional area, in square feet = 15.9*(drainage area, in square mile)0.656.The coefficients of determination (R2) for these four equations were 0.94, 0.89, 0.52, and 0.96, respectively. The high coefficients of determination for three of these equations (discharge, width, and cross-sectional area) indicate that much of the range in the variables was explained by the drainage area. The low coefficient of determination for the equation relating bankfull depth to drainage area, however, suggests that other factors also affected water depth. Recurrence intervals for the estimated bankfull discharge of each stream ranged from 1.05 to 3.60 years; the mean recurrence interval was 2.13 years. The 10 surveyed streams were classified by Rosgen stream type; most were C- and E-type, with occasional B- and F-type cross sections. The equation (curve) for bankfull discharge for Region 7 was compared with those previously developed for four other hydrologic regions in New York State. The differences confirm that the hydraulic geometry of streams is affected by local climatic and physiographic conditions.

Projection-Based 3D Printing of Cell Patterning Scaffolds with Multiscale Channels.

PubMed

Xue, Dai; Wang, Yancheng; Zhang, Jiaxin; Mei, Deqing; Wang, Yue; Chen, Shaochen

2018-06-13

To fully actualize artificial, cell-laden biological models in tissue engineering, such as 3D organoids and organs-on-a-chip systems, cells need to be patterned such that they can precisely mimic natural microenvironments in vitro. Despite increasing interest in this area, patterning cells at multiscale (∼10 μm to 10 mm) remains a significant challenge in bioengineering. Here, we report a projection-based 3D printing system that achieves rapid and high-resolution fabrication of hydrogel scaffolds featuring intricate channels for multiscale cell patterning. Using this system, we were able to use biocompatible poly(ethylene glycol)diacrylate in fabricating a variety of scaffold architectures, ranging from regular geometries such as serpentine, spiral, and fractal-like to more irregular/intricate geometries, such as biomimetic arborescent and capillary networks. A red food dye solution was able to freely fill all channels in the scaffolds, from the trunk (>1100 μm in width) to the small branch (∼17 μm in width) without an external pump. The dimensions of the printed scaffolds remained stable over 3 days while being immersed in Dulbecco's phosphate-buffered saline at 37 °C, and a penetration analysis revealed that these scaffolds are suitable for metabolic and nutrient transport. Cell patterning experiments showed that red fluorescent protein-transfected A549 human nonsmall lung cancer cells adhered well in the scaffolds' channels, and showed further attachment and penetration during cell culture proliferation.

Research on width control of Metal Fused-coating Additive Manufacturing based on active control

NASA Astrophysics Data System (ADS)

Ren, Chuan qi; Wei, Zheng ying; Wang, Xin; Du, Jun; Zhang, Shan; Zhang, Zhitong; Bai, Hao

2017-12-01

Given the stability of the shape of the forming layer is one of the key problems that affect the final quality of the sample morphology, taking a study on the forming process and the control method of morphology make a significant difference to metal fused-coating additive manufacturing (MFCAM) in achieving the efficient and stable forming. To improve the quality and precision of the samples of single-layer single pass, a control method of morphology based on active control was established by this paper. The real-time acquisition of image was realized by CCD and the characteristics of morphology of the forming process were simultaneously extracted. Making analysis of the characteristics of the width during the process, the relationship between the relative difference of different frames and moving speed was given. A large number of experiments are used to verify the response speed and accuracy of the system. The results show that the active system can improve the morphology of the sample and the smoothness of the width of the single channel, and increase the uniformity of width by 55.16%.

Effects of streamflows on stream-channel morphology in the eastern Niobrara National Scenic River, Nebraska, 1988–2010

USGS Publications Warehouse

Schaepe, Nathaniel J.; Alexander, Jason S.; Folz-Donahue, Kiernan

2016-03-09

Changes in channel metrics generally corresponded to changes in streamflow conditions, but other than changes in incipient flood-plain area, these changes were small and were not measured in all three segments simultaneously. Increases in total channel width (except in segment 1) and incipient flood-plain area between 1993 and 1999 corresponded to increases in streamflow. Channel narrowing (except in segment 1) between 1999 and 2003 corresponded to lower summer streamflows and extended durations of very low summer streamflow. Although the pattern of low summer streamflow and extended durations of very low summer streamflow continued during the 2004–6 period and at the beginning of the 2007–10 period, no further narrowing was measured. Consistent tributary summer inflows help to explain the resistance of segments 2 and 3 to further narrowing. Because segment 1 is already much narrower than segments 2 and 3, its average current velocity is likely to be swifter and, therefore, competent to offset further effects of the processes that led to its narrowness.

The impact of channel capture on estuarine hydro-morphodynamics and water quality in the Amazon delta.

PubMed

Silva Dos Santos, Eldo; Pinheiro Lopes, Paula Patrícia; da Silva Pereira, Hyrla Herondina; de Oliveira Nascimento, Otávio; Rennie, Colin David; da Silveira Lobo O'Reilly Sternberg, Leonel; Cavalcanti da Cunha, Alan

2018-05-15

Due to progressive erosion of the new Urucurituba Channel, the Amazon River has recently captured almost all discharge from the lower Araguari River (Amapá-AP, Brazil), which previously flowed directly to the Atlantic Ocean. These recent geomorphological changes have caused strong impacts on the landscape and hydrodynamic patterns near the Araguari River mouth, especially the alteration of the riverine drainage system and its water quality. Landsat images were used to assess the estuarine landscape morphodynamic, particularly the expansion of the Urucurituba Channel, 80km from the Araguari River mouth, chronicling its connection to the Amazon River. The results suggest that the Urucurituba developed by headward migration across the Amazon delta; this is perhaps the first observation of estuarine distributary network development by headward channel erosion. The rate of Urucurituba Channel width increase has been ≈5m/month since 2011, increasing drainage capacity of the channel. We also collected in situ hydrodynamic measurements and analyzed 17 water quality parameters. Having 2011 as baseline, the flowrate of Araguari River has been diverted by up to 98% through Urucurituba Channel, with substantial changes in net discharge recorded at 3 monitoring stations. Statistically significant differences in water quality (p<0.05) were observed between 2011 and 2015, associated with the change in the flow pattern. Estuarine salinity and solids concentrations have increased. Overall, we demonstrate changes in landscape, hydrodynamics and water quality of the lower Araguari River. Copyright © 2017 Elsevier B.V. All rights reserved.

Assessing geomorphic sensitivity in relation to river capacity for adjustment

NASA Astrophysics Data System (ADS)

Reid, H. E.; Brierley, G. J.

2015-12-01

River sensitivity describes the nature and rate of channel adjustments. An approach to analysis of geomorphic river sensitivity outlined in this paper relates potential sensitivity based on the expected capacity of adjustment for a river type to the recent history of channel adjustment. This approach was trialled to assess low, moderate and high geomorphic sensitivity for four different types of river (10 reaches in total) along the Lower Tongariro River, North Island, New Zealand. Building upon the River Styles framework, river types were differentiated based upon valley setting (width and confinement), channel planform, geomorphic unit assemblages and bed material size. From this, the behavioural regime and potential for adjustment (type and extent) were determined. Historical maps and aerial photographs were geo-rectified and the channel planform digitised to assess channel adjustments for each reach from 1928 to 2007. Floodplain width controlled by terraces, exerted a strong influence upon reach scale sensitivity for the partly-confined, wandering, cobble-bed river. Although forced boundaries occur infrequently, the width of the active channel zone is constrained. An unconfined braided river reach directly downstream of the terrace-confined section was the most geomorphically sensitive reach. The channel in this reach adjusted recurrently to sediment inputs that were flushed through more confined, better connected upstream reaches. A meandering, sand-bed river in downstream reaches has exhibited negligible rates of channel migration. However, channel narrowing in this reach and the associated delta indicate that the system is approaching a threshold condition, beyond which channel avulsion is likely to occur. As this would trigger more rapid migration, this reach is considered to be more geomorphically sensitive than analysis of its low migration rate alone would indicate. This demonstrates how sensitivity is fashioned both by the behavioural regime of a reach and flow/sediment input from upstream. The approach to assess geomorphic river sensitivity outlined here could support 'room to move' or 'freedom space' approaches to river management by relating likely channel adjustments for the type of river under consideration to the area of land that is required to contain 'natural' patterns and rates of geomorphic functionality.

Large wood recruitment and redistribution in headwater streams in the southern Oregon Coast Range, U.S.A

USGS Publications Warehouse

May, Christine L.; Gresswell, Robert E.

2003-01-01

Large wood recruitment and redistribution mechanisms were investigated in a 3.9 km2 basin with an old-growth Pseudotsuga menziesii (Mirb.) Franco and Tsuga heterophylla (Raf.) Sarg. forest, located in the southern Coast Range of Oregon. Stream size and topographic setting strongly influenced processes that delivered wood to the channel network. In small colluvial channels draining steep hillslopes, processes associated with slope instability dominated large wood recruitment. In the larger alluvial channel, windthrow was the dominant recruitment process from the local riparian area. Consequently, colluvial channels received wood from further upslope than the alluvial channel. Input and redistribution processes influenced piece location relative to the direction of flow and thus, affected the functional role of wood. Wood recruited directly from local hillslopes and riparian areas was typically positioned adjacent to the channel or spanned its full width, and trapped sediment and wood in transport. In contrast, wood that had been fluvially redistributed was commonly located in mid-channel positions and was associated with scouring of the streambed and banks. Debris flows were a unique mechanism for creating large accumulations of wood in small streams that lacked the capacity for abundant fluvial transport of wood, and for transporting wood that was longer than the bank-full width of the channel.

Micro-channel filling flow considering surface tension effect

NASA Astrophysics Data System (ADS)

Kim, Dong Sung; Lee, Kwang-Cheol; Kwon, Tai Hun; Lee, Seung S.

2002-05-01

Understanding filling flow into micro-channels is important in designing micro-injection molding, micro-fluidic devices and an MIMIC (micromolding in capillaries) process. In this paper, we investigated, both experimentally and numerically, 'transient filling' flow into micro-channels, which differs from steady-state completely 'filled' flow in micro-channels. An experimental flow visualization system was devised to facilitate observation of flow characteristics in filling into micro-channels. Three sets of micro-channels of various widths of different thicknesses (20, 30, and 40 μm) were fabricated using SU-8 on the silicon substrate to find a geometric effect with regard to pressure gradient, viscous force and, in particular, surface tension. A numerical analysis system has also been developed taking into account the surface tension effect with a contact angle concept. Experimental observations indicate that surface tension significantly affects the filling flow to such an extent that even a flow blockage phenomenon was observed at channels of small width and thickness. A numerical analysis system also confirms that the flow blockage phenomenon could take place due to the flow hindrance effect of surface tension, which is consistent with experimental observation. For proper numerical simulations, two correction factors have also been proposed to correct the conventional hydraulic radius for the filling flow in rectangular cross-sectioned channels.

A morphology independent methodology for quantifying planview river change and characteristics from remotely sensed imagery

DOE PAGES

Rowland, Joel C.; Shelef, Eitan; Pope, Paul A.; ...

2016-07-15

Remotely sensed imagery of rivers has long served as a means for characterizing channel properties and detection of planview change. In the last decade the dramatic increase in the availability of satellite imagery and processing tools has created the potential to greatly expand the spatial and temporal scale of our understanding of river morphology and dynamics. To date, the majority of GIS and automated analyses of planview changes in rivers from remotely sensed data has been developed for single-threaded meandering river systems. These methods have limited applicability to many of the earth's rivers with complex multi-channel planforms. Here we presentmore » the methodologies of a set of analysis algorithms collectively called Spatially Continuous Riverbank Erosion and Accretion Measurements (SCREAM). SCREAM analyzes planview river metrics regardless of river morphology. These algorithms quantify both the erosion and accretion rates of riverbanks from binary masks of channels generated from imagery acquired at two time periods. Additionally, the program quantifies the area of change between river channels and the surrounding floodplain and area of islands lost or formed between these two time periods. To examine variations in erosion rates in relation to local channel attributes and make rate comparisons between river systems of varying sizes, the program determines channel widths and bank curvature at every bank pixel. SCREAM was developed and tested on rivers with diverse and complex planform morphologies in imagery acquired from a range of observational platforms with varying spatial resolutions. Here, validation and verification of SCREAM-generated metrics against manual measurements show no significant measurement errors in determination of channel width, erosion, and bank aspects. SCREAM has the potential to provide data for both the quantitative examination of the controls on erosion rates and for the comparison of these rates across river systems ranging broadly in size and planform morphology.« less

Navigability Potential of Washington Rivers and Streams Determined with Hydraulic Geometry and a Geographic Information System

USGS Publications Warehouse

Magirl, Christopher S.; Olsen, Theresa D.

2009-01-01

Using discharge and channel geometry measurements from U.S. Geological Survey streamflow-gaging stations and data from a geographic information system, regression relations were derived to predict river depth, top width, and bottom width as a function of mean annual discharge for rivers in the State of Washington. A new technique also was proposed to determine bottom width in channels, a parameter that has received relatively little attention in the geomorphology literature. These regression equations, when combined with estimates of mean annual discharge available in the National Hydrography Dataset, enabled the prediction of hydraulic geometry for any stream or river in the State of Washington. Predictions of hydraulic geometry can then be compared to thresholds established by the Washington State Department of Natural Resources to determine navigability potential of rivers. Rivers with a mean annual discharge of 1,660 cubic feet per second or greater are 'probably navigable' and rivers with a mean annual discharge of 360 cubic feet per second or less are 'probably not navigable'. Variance in the dataset, however, leads to a relatively wide range of prediction intervals. For example, although the predicted hydraulic depth at a mean annual discharge of 1,660 cubic feet per second is 3.5 feet, 90-percent prediction intervals indicate that the actual hydraulic depth may range from 1.8 to 7.0 feet. This methodology does not determine navigability - a legal concept determined by federal common law - instead, this methodology is a tool for predicting channel depth, top width, and bottom width for rivers and streams in Washington.

Split-cross-bridge resistor for testing for proper fabrication of integrated circuits

NASA Technical Reports Server (NTRS)

Buehler, M. G. (Inventor)

1985-01-01

An electrical testing structure and method is described whereby a test structure is fabricated on a large scale integrated circuit wafer along with the circuit components and has a van der Pauw cross resistor in conjunction with a bridge resistor and a split bridge resistor, the latter having two channels each a line width wide, corresponding to the line width of the wafer circuit components, and with the two channels separated by a space equal to the line spacing of the wafer circuit components. The testing structure has associated voltage and current contact pads arranged in a two by four array for conveniently passing currents through the test structure and measuring voltages at appropriate points to calculate the sheet resistance, line width, line spacing, and line pitch of the circuit components on the wafer electrically.

Multichannel extremely broadband near-IR radiation sources for optical coherence tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wojtkowski, M; Fujimoto, J G; Lapin, P I

The construction and output parameters of two experimental samples of near-IR radiation sources based on the superposition of radiation from several superluminescent diodes are described. The first, three-channel sample emitting 18 mW of cw output power in a spectral band of width 105 nm through a single-mode fibre, is optimised for ophthalmology coherence tomography. The second, four-channel sample emits the 870-nm band of width more than 200 nm, which corresponds to the record coherence length smaller than 4 {mu}m. (laser applications and other topics in quantum electronics)

Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity and temperature profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pooja,, E-mail: pupooja16@gmail.com; Ahluwalia, P. K., E-mail: pk-ahluwalia7@yahoo.com; Pathania, Y.

2015-05-15

This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0.more » To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow.« less

Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity & temperature profiles

NASA Astrophysics Data System (ADS)

Pooja, Pathania, Y.; Ahluwalia, P. K.

2015-05-01

This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0. To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow.

Formation and maintenance of single-thread tie channels entering floodplain lakes: Observations from three diverse river systems

NASA Astrophysics Data System (ADS)

Rowland, J. C.; Dietrich, W. E.; Day, G.; Parker, G.

2009-06-01

Tie channels connect rivers to floodplain lakes on many lowland rivers and thereby play a central role in floodplain sedimentology and ecology; yet they are generally unrecognized and little studied. Here we report the results of field studies focused on tie channel origin and morphodynamics in the following three contrasting systems: the Middle Fly River (Papua New Guinea), the Lower Mississippi River, and Birch Creek in Alaska. Across these river systems, tie channels vary by an order of magnitude in size but exhibit the same characteristic morphology and appear to develop and evolve by a similar set of processes. In all three systems, the channels are characterized by a narrow, leveed, single-thread morphology with maximum width approximately one tenth the width of the mainstem river. The channels typically have a V-shaped cross section, unlike most fluvial channels. These channels develop as lakes become isolated from the river by sedimentation. Narrowing of the connection between river and lake causes a sediment-laden jet to develop. Levees develop along the margins of the jet leading to channel emergence and eventual levee aggradation to the height of the mainstem levees. Bidirectional flow in these channels is common. Outflows from the lake scour sediment and prevent channel blockage. We propose that channel geometry and size are then controlled by a dynamic balance between channel narrowing by suspended sediment deposition and incision and widening by mass failure of banks during outflows. Tie channels are laterally stable and may convey flow for hundreds to a few thousand of years.

Gravity currents in rotating channels. Part 1. Steady-state theory

NASA Astrophysics Data System (ADS)

Hacker, J. N.; Linden, P. F.

2002-04-01

A theory is developed for the speed and structure of steady-state non-dissipative gravity currents in rotating channels. The theory is an extension of that of Benjamin (1968) for non-rotating gravity currents, and in a similar way makes use of the steady-state and perfect-fluid (incompressible, inviscid and immiscible) approximations, and supposes the existence of a hydrostatic ‘control point’ in the current some distance away from the nose. The model allows for fully non-hydrostatic and ageostrophic motion in a control volume V ahead of the control point, with the solution being determined by the requirements, consistent with the perfect-fluid approximation, of energy and momentum conservation in V, as expressed by Bernoulli's theorem and a generalized flow-force balance. The governing parameter in the problem, which expresses the strength of the background rotation, is the ratio W = B/R, where B is the channel width and R = (g[prime prime or minute]H)1/2/f is the internal Rossby radius of deformation based on the total depth of the ambient fluid H. Analytic solutions are determined for the particular case of zero front-relative flow within the gravity current. For each value of W there is a unique non-dissipative two-layer solution, and a non-dissipative one-layer solution which is specified by the value of the wall-depth h0. In the two-layer case, the non-dimensional propagation speed c = cf(g[prime prime or minute]H)[minus sign]1/2 increases smoothly from the non-rotating value of 0.5 as W increases, asymptoting to unity for W [rightward arrow] [infty infinity]. The gravity current separates from the left-hand wall of the channel at W = 0.67 and thereafter has decreasing width. The depth of the current at the right-hand wall, h0, increases, reaching the full depth at W = 1.90, after which point the interface outcrops on both the upper and lower boundaries, with the distance over which the interface slopes being 0.881R. In the one-layer case, the wall-depth based propagation speed Froude number c0 = cf(g[prime prime or minute]h0)[minus sign]1/2 = 21/2, as in the non-rotating one-layer case. The current separates from the left-hand wall of the channel at W0 [identical with] B/R0 = 2[minus sign]1/2, and thereafter has width 2[minus sign]1/2R0, where R0 = (g[prime prime or minute]h0)1/2/f is the wall-depth based deformation radius.

Distinctive fingerprints of erosional regimes in terrestrial channel networks

NASA Astrophysics Data System (ADS)

Grau Galofre, A.; Jellinek, M.

2017-12-01

Satellite imagery and digital elevation maps capture the large scale morphology of channel networks attributed to long term erosional processes, such as fluvial, glacial, groundwater sapping and subglacial erosion. Characteristic morphologies associated with each of these styles of erosion have been studied in detail, but there exists a knowledge gap related to their parameterization and quantification. This knowledge gap prevents a rigorous analysis of the dominant processes that shaped a particular landscape, and a comparison across styles of erosion. To address this gap, we use previous morphological descriptions of glaciers, rivers, sapping valleys and tunnel valleys to identify and measure quantitative metrics diagnostic of these distinctive styles of erosion. From digital elevation models, we identify four geometric metrics: The minimum channel width, channel aspect ratio (longest length to channel width at the outlet), presence of undulating longitudinal profiles, and tributary junction angle. We also parameterize channel network complexity in terms of its stream order and fractal dimension. We then perform a statistical classification of the channel networks using a Principal Component Analysis on measurements of these six metrics on a dataset of 70 channelized systems. We show that rivers, glaciers, groundwater seepage and subglacial meltwater erode the landscape in rigorously distinguishable ways. Our methodology can more generally be applied to identify the contributions of different processes involved in carving a channel network. In particular, we are able to identify transitions from fluvial to glaciated landscapes or vice-versa.

Parsimonious mathematical characterization of channel shape and size

USDA-ARS?s Scientific Manuscript database

This work has two purposes: 1) using a Leopold and Maddock (1953) hydraulic geometry approach, present a mathematically parsimonious, two parameter, characterization of channel shape and size; and 2) analytically quantify cross-sectional area, top width, average depth, critical energy, and bankfull ...

Downstream effects of Flaming Forge Reservoir on the Green River, Colorado and Utah.

USGS Publications Warehouse

Andrews, E.D.

1986-01-01

In response to the reduced peak discharges, the bankfull channel width of the Green River has decreased by c10%. Adjustment of the channel to decreased peak flows and altered sediment loads is nowhere complete.-from Author

Oscillation of Branching Ratios Between the D(2s)+D(1s) and the D(2p)+D(1s) Channels in Direct Photodissociation of D_{2}.

PubMed

Wang, Jie; Meng, Qingnan; Mo, Yuxiang

2017-08-04

The direct photodissociation of D_{2} at excitation energies above 14.76 eV occurs via two channels, D(2s)+D(1s) and D(2p)+D(1s). The branching ratios between the two have been measured from the dissociation threshold to 3200 cm^{-1} above it, and it is found that they show cosine oscillations as a function of the fragment wave vector magnitudes. The oscillation is due to an interference effect and can be simulated using the phase difference between the wave functions of the two channels, analogous to Young's double-slit experiment. By fitting the measured branching ratios, we have determined the depths and widths of the effective spherical potential wells related to the two channels, which are in agreement with the effective depths and widths of the ab initio interaction potentials. The results of this Letter illustrate the importance of the relative phase between the fragments in controlling the branching ratios of the photodissociation channels.

Oscillation of Branching Ratios Between the D (2 s )+D (1 s ) and the D (2 p )+D (1 s ) Channels in Direct Photodissociation of D2

NASA Astrophysics Data System (ADS)

Wang, Jie; Meng, Qingnan; Mo, Yuxiang

2017-08-01

The direct photodissociation of D2 at excitation energies above 14.76 eV occurs via two channels, D (2 s )+D (1 s ) and D (2 p )+D (1 s ) . The branching ratios between the two have been measured from the dissociation threshold to 3200 cm-1 above it, and it is found that they show cosine oscillations as a function of the fragment wave vector magnitudes. The oscillation is due to an interference effect and can be simulated using the phase difference between the wave functions of the two channels, analogous to Young's double-slit experiment. By fitting the measured branching ratios, we have determined the depths and widths of the effective spherical potential wells related to the two channels, which are in agreement with the effective depths and widths of the ab initio interaction potentials. The results of this Letter illustrate the importance of the relative phase between the fragments in controlling the branching ratios of the photodissociation channels.

The respective effect of under-rib convection and pressure drop of flow fields on the performance of PEM fuel cells.

PubMed

Wang, Chao; Zhang, Qinglei; Shen, Shuiyun; Yan, Xiaohui; Zhu, Fengjuan; Cheng, Xiaojing; Zhang, Junliang

2017-03-02

The flow field configuration plays an important role on the performance of proton exchange membrane fuel cells (PEMFCs). For instance, channel/rib width and total channel cross-sectional area determine the under-rib convection and pressure drop respectively, both of which directly influence the water removal, in turn affecting the oxygen supply and cathodic oxygen reduction reaction. In this study, effects of under-rib convection and pressure drop on cell performance are investigated experimentally and numerically by adjusting the channel/rib width and channel cross-sectional area of flow fields. The results show that the performance differences with various flow field configurations mainly derive from the oxygen transport resistance which is determined by the water accumulation degree, and the cell performance would benefit from the narrower channels and smaller cross sections. It reveals that at low current densities when water starts to accumulate in GDL at under-rib regions, the under-rib convection plays a more important role in water removal than pressure drop does; in contrast, at high current densities when water starts to accumulate in channels, the pressure drop dominates the water removal to facilitate the oxygen transport to the catalyst layer.

The respective effect of under-rib convection and pressure drop of flow fields on the performance of PEM fuel cells

NASA Astrophysics Data System (ADS)

Wang, Chao; Zhang, Qinglei; Shen, Shuiyun; Yan, Xiaohui; Zhu, Fengjuan; Cheng, Xiaojing; Zhang, Junliang

2017-03-01

The flow field configuration plays an important role on the performance of proton exchange membrane fuel cells (PEMFCs). For instance, channel/rib width and total channel cross-sectional area determine the under-rib convection and pressure drop respectively, both of which directly influence the water removal, in turn affecting the oxygen supply and cathodic oxygen reduction reaction. In this study, effects of under-rib convection and pressure drop on cell performance are investigated experimentally and numerically by adjusting the channel/rib width and channel cross-sectional area of flow fields. The results show that the performance differences with various flow field configurations mainly derive from the oxygen transport resistance which is determined by the water accumulation degree, and the cell performance would benefit from the narrower channels and smaller cross sections. It reveals that at low current densities when water starts to accumulate in GDL at under-rib regions, the under-rib convection plays a more important role in water removal than pressure drop does; in contrast, at high current densities when water starts to accumulate in channels, the pressure drop dominates the water removal to facilitate the oxygen transport to the catalyst layer.

Don't Fence Me In: Free Meanders in a Confined River Valley

NASA Astrophysics Data System (ADS)

Eke, E. C.; Wilcock, P. R.

2015-12-01

The interaction between meandering river channels and inerodible valley walls provides a useful test of our ability to understand meander dynamics. In some cases, river meanders confined between valley walls display distinctive angular bends in a dynamic equilibrium such that their size and shape persist as the meander migrates. In other cases, meander geometry is more varied and changes as the meander migrates. The ratio of channel to valley width has been identified as a useful parameter for defining confined meanders, but is not sufficient to distinguish cases in which sharp angular bends are able to migrate with little change in geometry. Here, we examine the effect of water and sediment supply on the geometry of confined rivers in order to identify conditions under which meander geometry reaches a persistent dynamic equilibrium. Because channel width and meander geometry are closely related, we use a numerical meander model that allows for independent migration of both banks, thereby allowing channel width to vary in space and time. We hypothesize that confined meanders with persistent angular bends have smaller transport rates of bed material and that their migration is driven by erosion of the cutbank (bank-pull migration). When bed material supply is sufficiently large that point bar deposition drives meander migration (bar-push migration), confined meander bends have a larger radius of curvature and a geometry that varies as the meander migrates. We test this hypothesis using historical patterns of confined meander migration for rivers with different rates of sediment supply and bed material transport. Interpretation of the meander migration pattern is provided by the free-width meander migration model.

Design of multiplier-less sharp transition width non-uniform filter banks using gravitational search algorithm

NASA Astrophysics Data System (ADS)

Bindiya T., S.; Elias, Elizabeth

2015-01-01

In this paper, multiplier-less near-perfect reconstruction tree-structured filter banks are proposed. Filters with sharp transition width are preferred in filter banks in order to reduce the aliasing between adjacent channels. When sharp transition width filters are designed as conventional finite impulse response filters, the order of the filters will become very high leading to increased complexity. The frequency response masking (FRM) method is known to result in linear-phase sharp transition width filters with low complexity. It is found that the proposed design method, which is based on FRM, gives better results compared to the earlier reported results, in terms of the number of multipliers when sharp transition width filter banks are needed. To further reduce the complexity and power consumption, the tree-structured filter bank is made totally multiplier-less by converting the continuous filter bank coefficients to finite precision coefficients in the signed power of two space. This may lead to performance degradation and calls for the use of a suitable optimisation technique. In this paper, gravitational search algorithm is proposed to be used in the design of the multiplier-less tree-structured uniform as well as non-uniform filter banks. This design method results in uniform and non-uniform filter banks which are simple, alias-free, linear phase and multiplier-less and have sharp transition width.

Precision measurement of the mass and width of the W boson at CDF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malik, Sarah Alam

2009-09-01

A precision measurement of the mass and width of the W boson is presented. The W bosons are produced in proton antiproton collisions occurring at a centre of mass energy of 1.96 TeV at the Tevatron accelerator. The data used for the analyses is collected by the Collider Detector at Fermilab (CDF) and corresponds to an average integrated luminosity of 350 pb -1 for the W width analysis for the electron and muon channels and an average integrated luminosity of 2350 pb -1 for the W mass analysis. The mass and width of the W boson is extracted by fittingmore » to the transverse mass distribution, with the peak of the distribution being most sensitive to the mass and the tail of the distribution sensitive to the width. The W width measurement in the electron and muon channels is combined to give a final result of 2032 ± 73 MeV. The systematic uncertainty on the W mass from the recoil of the W boson against the initial state gluon radiation is discussed. A systematic study of the recoil in Z → e +e - events where one electron is reconstructed in the central calorimeter and the other in the plug calorimeter and its effect on the W mass is presented for the first time in this thesis.« less

Quantitative Characterisation and Analysis of Siliciclastic Fluvial Depositional Systems Using 3D Digital Outcrop Models

NASA Astrophysics Data System (ADS)

Burnham, Brian Scott

Outcrop analogue studies of fluvial sedimentary systems are often undertaken to identify spatial and temporal characteristics (e.g. stacking patterns, lateral continuity, lithofacies proportions). However, the lateral extent typically exceeds that of the exposure, and/or the true width and thickness are not apparent. Accurate characterisation of fluvial sand bodies is integral for accurate identification and subsequent modelling of aquifer and hydrocarbon reservoir architecture. The studies presented in this thesis utilise techniques that integrate lidar, highresolution photography and differential geospatial measurements, to create accurate three-dimensional (3D) digital outcrop models (DOMs) of continuous 3D and laterally extensive 2D outcrop exposures. The sedimentary architecture of outcrops in the medial portion of a large Distributive Fluvial System (DFS) (Huesca fluvial fan) in the Ebro Basin, north-east Spain, and in the fluvio-deltaic succession of the Breathitt Group in the eastern Appalachian Basin, USA, are evaluated using traditional sedimentological and digital outcrop analytical techniques. The major sand bodies in the study areas are quantitatively analysed to accurately characterise spatial and temporal changes in sand body architecture, from two different outcrop exposure types and scales. Several stochastic reservoir simulations were created to approximate fluvial sand body lithological component and connectivity within the medial portion of the Huesca DFS. Results demonstrate a workflow and current methodology adaptation of digital outcrop techniques required for each study to approximate true geobody widths, thickness and characterise architectural patterns (internal and external) of major fluvial sand bodies interpreted as products of DFSs in the Huesca fluvial fan, and both palaeovalleys and progradational DFSs in the Pikeville and Hyden Formations in the Breathitt Group. The results suggest key geostatistical metrics, which are translatable across any fluvial system that can be used to analyse 3D digital outcrop data, and identify spatial attributes of sand bodies to identify their genetic origin and lithological component within fluvial reservoir systems, and the rock record. 3D quantitative analysis of major sand bodies have allowed more accurate width vs. thickness relationships within the La Serreta area, showing a vertical increase in width and channel-fill facies, and demonstrates a 22% increase of in-channel facies from previous interpretations. Additionally, identification of deposits that are products of a nodal avulsion event have been characterised and are interpreted to be the cause for the increase in width and channel-fill facies. Furthermore, analysis of the Pikeville and Hyden Fms contain sand bodies of stacked distributaries and palaeovalleys, as previously interpreted, and demonstrates that a 3D spatial approach to determine basin-wide architectural trends is integral to identifying the genetic origin, and preservation potential of sand bodies of both palaeovalleys and distributive fluvial systems. The resultant geostatistics assimilated in the thesis demonstrates the efficacy of integrated lidar studies of outcrop analogues, and provide empirical relationships which can be applied to subsurface analogues for reservoir model development and the distribution of both DFS and palaeovalley depositional systems in the rock record.

Methods for estimating streamflow at mountain fronts in southern New Mexico

USGS Publications Warehouse

Waltemeyer, S.D.

1994-01-01

The infiltration of streamflow is potential recharge to alluvial-basin aquifers at or near mountain fronts in southern New Mexico. Data for 13 streamflow-gaging stations were used to determine a relation between mean annual stream- flow and basin and climatic conditions. Regression analysis was used to develop an equation that can be used to estimate mean annual streamflow on the basis of drainage areas and mean annual precipi- tation. The average standard error of estimate for this equation is 46 percent. Regression analysis also was used to develop an equation to estimate mean annual streamflow on the basis of active- channel width. Measurements of the width of active channels were determined for 6 of the 13 gaging stations. The average standard error of estimate for this relation is 29 percent. Stream- flow estimates made using a regression equation based on channel geometry are considered more reliable than estimates made from an equation based on regional relations of basin and climatic conditions. The sample size used to develop these relations was small, however, and the reported standard error of estimate may not represent that of the entire population. Active-channel-width measurements were made at 23 ungaged sites along the Rio Grande upstream from Elephant Butte Reservoir. Data for additional sites would be needed for a more comprehensive assessment of mean annual streamflow in southern New Mexico.

Control of interaction strength in a network of the true slime mold by a microfabricated structure.

PubMed

Takamatsu, A; Fujii, T; Endo, I

2000-02-01

The plasmodium of the true slime mold, Physarum polycephalum, which shows various nonlinear oscillatory phenomena, for example, in its thickness, protoplasmic streaming and concentration of intracellular chemicals, can be regarded as a collective of nonlinear oscillators. The plasmodial oscillators are interconnected by microscale tubes whose dimensions can be closely related to the strength of interaction between the oscillators. Investigation of the collective behavior of the oscillators under the conditions in which the interaction strength can be systematically controlled gives significant information on the characteristics of the system. In this study, we proposed a living model system of a coupled oscillator system in the Physarum plasmodium. We patterned the geometry and dimensions of the microscale tube structure in the plasmodium by a microfabricated structure (microstructure). As the first step, we constructed a two-oscillator system for the plasmodium that has two wells (oscillator part) and a channel (coupling part). We investigated the oscillation behavior by monitoring the thickness oscillation of the plasmodium in the microstructure with various channel widths. It was found that the oscillation behavior of two oscillators dynamically changed depending on the channel width. Based on the results of measurements of the tube dimensions and the velocity of the protoplasmic streaming in the tube, we discuss how the channel width relates to the interaction strength of the coupled oscillator system.

Effects of fringing reefs on tsunami inundation: American Samoa

USGS Publications Warehouse

Gelfenbaum, G.; Apotsos, A.; Stevens, A.W.; Jaffe, B.

2011-01-01

A numerical model of tsunami inundation, Delft3D, which has been validated for the 29 September 2009 tsunami in Tutuila, American Samoa, is used to better understand the impact of fringing coral reefs and embayments on tsunami wave heights, inundation distances, and velocities. The inundation model is used to explore the general conditions under which fringing reefs act as coastal buffers against incoming tsunamis. Of particular interest is the response of tsunamis to reefs of varying widths, depths, and roughness, as well as the effects of channels incised in the reef and the focusing effect of embayments. Model simulations for conditions similar to Tutuila, yet simplified to be uniform in the alongshore, suggest that for narrow reefs, less than about 200 m wide, the shoaling owing to shallow water depths over the fringing reef dominates, inducing greater wave heights onshore under some conditions and farther inundation inland. As the reef width increases, wave dissipation through bottom friction begins to dominate and the reef causes the tsunami wave heights to decrease and the tsunami to inundate less far inland. A sensitivity analysis suggests that coral reef roughness is important in determining the manner in which a fringing reef affects tsunami inundation. Smooth reefs are more likely to increase the onshore velocity within the tsunami compared to rough reefs. A larger velocity will likely result in an increased impact of the tsunami on structures and buildings. Simulations developed to explore 2D coastal morphology show that incised channels similar to those found around Tutuila, as well as coastal embayments, also affect tsunami inundation, allowing larger waves to penetrate farther inland. The largest effect is found for channels located within embayments, and for embayments that narrow landward. These simulations suggest that embayments that narrow landward, such as Fagafue Bay on the north side of Tutuila, and that have an incised deep channel, can cause a significant increase in tsunami wave heights, inundation distances, and velocities. Wide embayments, similar in size to Massacre Bay, induce some tsunami amplification, but not as much as for the narrowing embayment.

Effects of curved midline and varying width on the description of the effective diffusivity of Brownian particles

NASA Astrophysics Data System (ADS)

Chávez, Yoshua; Chacón-Acosta, Guillermo; Dagdug, Leonardo

2018-05-01

Axial diffusion in channels and tubes of smoothly-varying geometry can be approximately described as one-dimensional diffusion in the entropy potential with a position-dependent effective diffusion coefficient, by means of the modified Fick–Jacobs equation. In this work, we derive analytical expressions for the position-dependent effective diffusivity for two-dimensional asymmetric varying-width channels, and for three-dimensional curved midline tubes, formed by straight walls. To this end, we use a recently developed theoretical framework using the Frenet–Serret moving frame as the coordinate system (2016 J. Chem. Phys. 145 074105). For narrow tubes and channels, an effective one-dimensional description reducing the diffusion equation to a Fick–Jacobs-like equation in general coordinates is used. From this last equation, one can calculate the effective diffusion coefficient applying Neumann boundary conditions.

Sensing and Control Electronics for Low-Mass Low-Capacitance MEMS Accelerometers

DTIC Science & Technology

2002-05-01

R . Lewis (Analog Devices, Inc.) Spring 2002 Report Documentation Page Form ApprovedOMB No. 0704-0188 Public...10 −4 10 −3 Minimum noise floor vs frequency Frequency (Hz) N o is e F lo o r (g / r tH z) 10 4 10 5 10 6 10 7 10 8 40 50 60 70 80 90 100 Optimum...N o is e F lo o r (u g / r tH z) Noise floor vs channel width at 100 KHz 10 1 10 2 10 3 15 20 25 30 35 40 MOSFET Channel Width (um) N o is e F lo

High power vertical stacked diode laser development using macro-channel water cooling and hard solder bonding technology

NASA Astrophysics Data System (ADS)

Yu, Dongshan; Liang, Xuejie; Wang, Jingwei; Li, Xiaoning; Nie, Zhiqiang; Liu, Xingsheng

2017-02-01

A novel marco channel cooler (MaCC) has been developed for packaging high power diode vertical stacked (HPDL) lasers, which eliminates many of the issues in commercially-available copper micro-channel coolers (MCC). The MaCC coolers, which do not require deionized water as coolant, were carefully designed for compact size and superior thermal dissipation capability. Indium-free packaging technology was adopted throughout product design and fabrication process to minimize the risk of solder electromigration and thermal fatigue at high current density and long pulse width under QCW operation. Single MaCC unit with peak output power of up to 700W/bar at pulse width in microsecond range and 200W/bar at pulse width in millisecond range has been recorded. Characteristic comparison on thermal resistivity, spectrum, near filed and lifetime have been conducted between a MaCC product and its counterpart MCC product. QCW lifetime test (30ms 10Hz, 30% duty cycle) has also been conducted with distilled water as coolant. A vertical 40-MaCC stack product has been fabricated, total output power of 9 kilowatts has been recorded under QCW mode (3ms, 30Hz, 9% duty cycle).

Analysis of reach-scale elevation distribution in braided rivers: Definition of a new morphologic indicator and estimation of mean quantities

NASA Astrophysics Data System (ADS)

Redolfi, M.; Tubino, M.; Bertoldi, W.; Brasington, J.

2016-08-01

Understanding the role of external controls on the morphology of braided rivers is currently limited by the dearth of robust metrics to quantify and distinguish the diversity of channel form. Most existing measures are strongly dependent on river stage and unable to account for the three-dimensional complexity that is apparent in digital terrain models of braided rivers. In this paper, we introduce a simple, stage-independent morphological indicator that enables the analysis of reach-scale regime morphology as a function of slope, discharge, sediment size, and degree of confinement. The index is derived from the bed elevation frequency distribution and characterizes a statistical width-depth curve averaged longitudinally over multiple channel widths. In this way, we define a "synthetic channel" described by a simple parameter that embeds information about the river morphological complexity. Under the assumption of uniform flow, this approach can be extended to provide estimates of the reach-averaged shear stress distribution, bed load flux, and at-a-station-variability of wetted width. We test this approach using data from a wide range of labile channels including 58 flume experiments and three gravel bed braided rivers. Results demonstrate a strong relationship between the unit discharge and the shape of the elevation distribution, which varies between a U shape for typical single-thread confined channels and a Y shape for multithread reaches. Finally, we discuss the use of the metric as a diagnostic index of river condition that may be used to support inferences about the river morphological trajectory.

Study of inelastic decay amplitudes in /sup 51/Mn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whatley, K.M.

1982-01-01

Detailed angular distribution measurments on inelastically scattered protons and de-excitation ..gamma..-rays in the /sup 50/Cr(p,p') and /sup 50/Cr(p,p'..gamma..) reactions were performed for 107 resonances in /sup 51/Mn in the proton energy range 3.0-4.4 MeV. An overall resolution of 425 eV was obtained with the tandem Van de Graaff accelerator and the high resolution system at the Triangle Universities Nuclear Laboratory. Spin and parity assignments for the 107 resonances studied were as follows: 1/2/sup +/ (4); 1/2/sup -/ (6); 3/2/sup -/ (30); 3/2/sup +/ (20); 5/2/sup +/ (38); 5/2/sup -/ (7); 7/2/sup +/ (1); and 9/2/sup +/ (1). Mixing ratios formore » the inelastic decay amplitudes were uniquely determined for all resonances except those assigned J/sup ..pi../ = 1/2/sup +/, 1/2/sup -/, or 3/2/sup +/. For 1/2/sup +/ and 1/2/sup -/ resonances there is only one open decay channel. For 3/2/sup +/ resonances, insufficient information is obtained from this experiment to determine a unique solution for the mixing ratios. Statistical studies were performed on the set of 3/2/sup -/ resonances and on the set of 5/2/sup +/ resonances. Strong channel-channel correlations were observed in the distributions of the reduced widths and the reduced width amplitudes for 5/2/sup +/ resonances. The existence of such correlations is a violation of the extreme statistical model. The present results agree with the reduced width amplitude distribution of Krieger and Porter which includes channel-channel correlations.« less

Sodium channels in the Cx43 gap junction perinexus may constitute a cardiac ephapse: an experimental and modeling study.

PubMed

Veeraraghavan, Rengasayee; Lin, Joyce; Hoeker, Gregory S; Keener, James P; Gourdie, Robert G; Poelzing, Steven

2015-10-01

It has long been held that electrical excitation spreads from cell-to-cell in the heart via low resistance gap junctions (GJ). However, it has also been proposed that myocytes could interact by non-GJ-mediated "ephaptic" mechanisms, facilitating propagation of action potentials in tandem with direct GJ-mediated coupling. We sought evidence that such mechanisms contribute to cardiac conduction. Using super-resolution microscopy, we demonstrate that Nav1.5 is localized within 200 nm of the GJ plaque (a region termed the perinexus). Electron microscopy revealed close apposition of adjacent cell membranes within perinexi suggesting that perinexal sodium channels could function as an ephapse, enabling ephaptic cell-to-cell transfer of electrical excitation. Acute interstitial edema (AIE) increased intermembrane distance at the perinexus and was associated with preferential transverse conduction slowing and increased spontaneous arrhythmia incidence. Inhibiting sodium channels with 0.5 μM flecainide uniformly slowed conduction, but sodium channel inhibition during AIE slowed conduction anisotropically and increased arrhythmia incidence more than AIE alone. Sodium channel inhibition during GJ uncoupling with 25 μM carbenoxolone slowed conduction anisotropically and was also highly proarrhythmic. A computational model of discretized extracellular microdomains (including ephaptic coupling) revealed that conduction trends associated with altered perinexal width, sodium channel conductance, and GJ coupling can be predicted when sodium channel density in the intercalated disk is relatively high. We provide evidence that cardiac conduction depends on a mathematically predicted ephaptic mode of coupling as well as GJ coupling. These data suggest opportunities for novel anti-arrhythmic therapies targeting noncanonical conduction pathways in the heart.

Methods for estimating flood frequency in Montana based on data through water year 1998

USGS Publications Warehouse

Parrett, Charles; Johnson, Dave R.

2004-01-01

Annual peak discharges having recurrence intervals of 2, 5, 10, 25, 50, 100, 200, and 500 years (T-year floods) were determined for 660 gaged sites in Montana and in adjacent areas of Idaho, Wyoming, and Canada, based on data through water year 1998. The updated flood-frequency information was subsequently used in regression analyses, either ordinary or generalized least squares, to develop equations relating T-year floods to various basin and climatic characteristics, equations relating T-year floods to active-channel width, and equations relating T-year floods to bankfull width. The equations can be used to estimate flood frequency at ungaged sites. Montana was divided into eight regions, within which flood characteristics were considered to be reasonably homogeneous, and the three sets of regression equations were developed for each region. A measure of the overall reliability of the regression equations is the average standard error of prediction. The average standard errors of prediction for the equations based on basin and climatic characteristics ranged from 37.4 percent to 134.1 percent. Average standard errors of prediction for the equations based on active-channel width ranged from 57.2 percent to 141.3 percent. Average standard errors of prediction for the equations based on bankfull width ranged from 63.1 percent to 155.5 percent. In most regions, the equations based on basin and climatic characteristics generally had smaller average standard errors of prediction than equations based on active-channel or bankfull width. An exception was the Southeast Plains Region, where all equations based on active-channel width had smaller average standard errors of prediction than equations based on basin and climatic characteristics or bankfull width. Methods for weighting estimates derived from the basin- and climatic-characteristic equations and the channel-width equations also were developed. The weights were based on the cross correlation of residuals from the different methods and the average standard errors of prediction. When all three methods were combined, the average standard errors of prediction ranged from 37.4 percent to 120.2 percent. Weighting of estimates reduced the standard errors of prediction for all T-year flood estimates in four regions, reduced the standard errors of prediction for some T-year flood estimates in two regions, and provided no reduction in average standard error of prediction in two regions. A computer program for solving the regression equations, weighting estimates, and determining reliability of individual estimates was developed and placed on the USGS Montana District World Wide Web page. A new regression method, termed Region of Influence regression, also was tested. Test results indicated that the Region of Influence method was not as reliable as the regional equations based on generalized least squares regression. Two additional methods for estimating flood frequency at ungaged sites located on the same streams as gaged sites also are described. The first method, based on a drainage-area-ratio adjustment, is intended for use on streams where the ungaged site of interest is located near a gaged site. The second method, based on interpolation between gaged sites, is intended for use on streams that have two or more streamflow-gaging stations.

Thermal analysis of a multi-layer microchannel heat sink for cooling concentrator photovoltaic (CPV) cells

NASA Astrophysics Data System (ADS)

Siyabi, Idris Al; Shanks, Katie; Mallick, Tapas; Sundaram, Senthilarasu

2017-09-01

Concentrator Photovoltaic (CPV) technology is increasingly being considered as an alternative option for solar electricity generation. However, increasing the light concentration ratio could decrease the system output power due to the increase in the temperature of the cells. The performance of a multi-layer microchannel heat sink configuration was evaluated using numerical analysis. In this analysis, three dimensional incompressible laminar steady flow model was solved numerically. An electrical and thermal solar cell model was coupled for solar cell temperature and efficiency calculations. Thermal resistance, solar cell temperature and pumping power were used for the system efficiency evaluation. An increase in the number of microchannel layers exhibited the best overall performance in terms of the thermal resistance, solar cell temperature uniformity and pressure drop. The channel height and width has no effect on the solar cell maximum temperature. However, increasing channel height leads to a reduction in the pressure drop and hence less fluid pumping power.

Numerical performance evaluation of design modifications on a centrifugal pump impeller running in reverse mode

NASA Astrophysics Data System (ADS)

Kassanos, Ioannis; Chrysovergis, Marios; Anagnostopoulos, John; Papantonis, Dimitris; Charalampopoulos, George

2016-06-01

In this paper the effect of impeller design variations on the performance of a centrifugal pump running as turbine is presented. Numerical simulations were performed after introducing various modifications in the design for various operating conditions. Specifically, the effects of the inlet edge shape, the meridional channel width, the number of blades and the addition of splitter blades on impeller performance was investigated. The results showed that, an increase in efficiency can be achieved by increasing the number of blades and by introducing splitter blades.

Observation of electric potential in organic thin-film transistor by bias-applied hard X-ray photoemission spectroscopy

NASA Astrophysics Data System (ADS)

Watanabe, Takeshi; Tada, Keisuke; Yasuno, Satoshi; Oji, Hiroshi; Yoshimoto, Noriyuki; Hirosawa, Ichiro

2016-03-01

The effect of gate voltage on electric potential in a pentacene (PEN) layer was studied by hard X-ray photoelectron spectroscopy under a bias voltage. It was observed that applying a negative gate voltage substantially increases the width of a C 1s peak. This suggested that injected and accumulated carriers in an organic thin film transistor channel modified the potential depth profile in PEN. It was also observed that the C 1s kinetic energy tends to increase monotonically with threshold voltage.

Controlling the ambipolarity and improvement of RF performance using Gaussian Drain Doped TFET

NASA Astrophysics Data System (ADS)

Nigam, Kaushal; Gupta, Sarthak; Pandey, Sunil; Kondekar, P. N.; Sharma, Dheeraj

2018-05-01

Ambipolar conduction in tunnel field-effect transistors (TFETs) has been occurred as an inherent issue due to drain-channel tunneling. It makes TFET less efficient and restricts its application in complementary digital circuits. Therefore, this manuscript reports the application of Gaussian doping profile on nanometer regime silicon channel TFETs to completely eliminate the ambipolarity. For this, Gaussian doping is used in the drain region of conventional gate-drain overlap TFET to control the tunneling of electrons from the valence band of channel to the conduction band of drain. As a result, barrier width at the drain/channel junction increases significantly leading to the suppression of an ambipolar current even when higher doping concentration (1 ? 10 ? cm ?) is considered in the drain region. However, significant improvement in terms of RF figure-of-merits such as cut-off frequency (f ?), gain bandwidth product (GBW), and gate-to-drain capacitance (C ?) is achieved with Gaussian doped gate on drain overlap TFET as compared to its counterpart TFET.

Comparison of High Aspect Ratio Cooling Channel Designs for a Rocket Combustion Chamber with Development of an Optimized Design

NASA Technical Reports Server (NTRS)

Wadel, Mary F.

1998-01-01

An analytical investigation on the effect of high aspect ratio (height/width) cooling channels, considering different coolant channel designs, on hot-gas-side wall temperature and coolant pressure drop for a liquid hydrogen cooled rocket combustion chamber, was performed. Coolant channel design elements considered were: length of combustion chamber in which high aspect ratio cooling was applied, number of coolant channels, and coolant channel shape. Seven coolant channel designs were investigated using a coupling of the Rocket Thermal Evaluation code and the Two-Dimensional Kinetics code. Initially, each coolant channel design was developed, without consideration for fabrication, to reduce the hot-gas-side wall temperature from a given conventional cooling channel baseline. These designs produced hot-gas-side wall temperature reductions up to 22 percent, with coolant pressure drop increases as low as 7.5 percent from the baseline. Fabrication constraints for milled channels were applied to the seven designs. These produced hot-gas-side wall temperature reductions of up to 20 percent, with coolant pressure drop increases as low as 2 percent. Using high aspect ratio cooling channels for the entire length of the combustion chamber had no additional benefit on hot-gas-side wall temperature over using high aspect ratio cooling channels only in the throat region, but increased coolant pressure drop 33 percent. Independent of coolant channel shape, high aspect ratio cooling was able to reduce the hot-gas-side wall temperature by at least 8 percent, with as low as a 2 percent increase in coolant pressure drop. ne design with the highest overall benefit to hot-gas-side wall temperature and minimal coolant pressure drop increase was the design which used bifurcated cooling channels and high aspect ratio cooling in the throat region. An optimized bifurcated high aspect ratio cooling channel design was developed which reduced the hot-gas-side wall temperature by 18 percent and reduced the coolant pressure drop by 4 percent. Reductions of coolant mass flow rate of up to 50 percent were possible before the hot-gas-side wall temperature reached that of the baseline. These mass flow rate reductions produced coolant pressure drops of up to 57 percent.

Erosional Consequence of Saltcedar Control

NASA Astrophysics Data System (ADS)

Vincent, Kirk R.; Friedman, Jonathan M.; Griffin, Eleanor R.

2009-08-01

Removal of nonnative riparian trees is accelerating to conserve water and improve habitat for native species. Widespread control of dominant species, however, can lead to unintended erosion. Helicopter herbicide application in 2003 along a 12-km reach of the Rio Puerco, New Mexico, eliminated the target invasive species saltcedar ( Tamarix spp.), which dominated the floodplain, as well as the native species sandbar willow ( Salix exigua Nuttall), which occurred as a fringe along the channel. Herbicide application initiated a natural experiment testing the importance of riparian vegetation for bank stability along this data-rich river. A flood three years later eroded about 680,000 m3 of sediment, increasing mean channel width of the sprayed reach by 84%. Erosion upstream and downstream from the sprayed reach during this flood was inconsequential. Sand eroded from channel banks was transported an average of 5 km downstream and deposited on the floodplain and channel bed. Although vegetation was killed across the floodplain in the sprayed reach, erosion was almost entirely confined to the channel banks. The absence of dense, flexible woody stems on the banks reduced drag on the flow, leading to high shear stress at the toe of the banks, fluvial erosion, bank undercutting, and mass failure. The potential for increased erosion must be included in consideration of phreatophyte control projects.

Erosional consequence of saltcedar control

USGS Publications Warehouse

Vincent, K.R.; Friedman, J.M.; Griffin, E.R.

2009-01-01

Removal of nonnative riparian trees is accelerating to conserve water and improve habitat for native species. Widespread control of dominant species, however, can lead to unintended erosion. Helicopter herbicide application in 2003 along a 12-km reach of the Rio Puerco, New Mexico, eliminated the target invasive species saltcedar (Tamarix spp.), which dominated the floodplain, as well as the native species sandbar willow (Salix exigua Nuttall), which occurred as a fringe along the channel. Herbicide application initiated a natural experiment testing the importance of riparian vegetation for bank stability along this data-rich river. A flood three years later eroded about 680,000 m3 of sediment, increasing mean channel width of the sprayed reach by 84%. Erosion upstream and downstream from the sprayed reach during this flood was inconsequential. Sand eroded from channel banks was transported an average of 5 km downstream and deposited on the floodplain and channel bed. Although vegetation was killed across the floodplain in the sprayed reach, erosion was almost entirely confined to the channel banks. The absence of dense, flexible woody stems on the banks reduced drag on the flow, leading to high shear stress at the toe of the banks, fluvial erosion, bank undercutting, and mass failure. The potential for increased erosion must be included in consideration of phreatophyte control projects. ?? 2009 U.S. Government.

Historical channel-planform change of the Little Colorado River near Winslow, Arizona

USGS Publications Warehouse

Block, Debra L.

2014-01-01

This study evaluates channel-planform adjustment on an alluvial reach of the Little Colorado River and documents the geomorphic evolution of the channel through an analysis of aerial photographs and orthophotographs for the period 1936–2010. The Little Colorado River has adjusted to the effects of an extreme flood in 1923 and a subsequent decline in peak discharge and mean annual flow by channel narrowing: the channel width and area of the river have decreased by approximately 90 percent over the study period. Although deposition historically exceeds erosion, lateral migration exacerbates localized erosion, particularly near hydraulic controls. Despite repeated cutoff and avulsion, the Little Colorado River has steadily increased in length and sinuosity over a period of 74 years. Changes in temperature and precipitation are likely affecting the discharge of the Little Colorado River near and downstream of Winslow, Ariz. Nonparametric methods of trend detection determine whether the probability distribution of temperature, precipitation, and peak streamflow has changed over time. Time-series plots of temperature and precipitation show statistically significant trends at the 99-percent-confidence level when evaluated with a Mann-Kendall test. An increasing trend was indicated in mean daily minimum air temperature (Tmin), whereas decreasing trends were indicated in both annual precipitation (Pann) and monsoon-seasonal precipitation (Pjas), as well as in peak discharge.

Bar dynamics and channel junctions in scale-experiments of estuaries

NASA Astrophysics Data System (ADS)

Leuven, J.; Braat, L.; van Dijk, W. M.; Haas, T. D.; Kleinhans, M. G.

2017-12-01

The evolution of channels and bars in estuaries has high socio-economic relevance, with strong implications for navigation, dredging and ecology. However, the spatial and temporal evolution of channels and bars in estuaries is poorly understood. Here, we study feedbacks of bar morphodynamics on widening and narrowing of estuaries. Therefore, we conducted an experiment in a 20 m long and 3 m wide tilting flume (the 'Metronome'), in which we monitored the evolution of a self-formed estuary that developed from an intial straight channel into an irregular planform with multiple channels, braided bars and a meandering ebb channel. At locations where the estuary width is confined, major channel junctions occur, while the zones between the junctions are characterised by high braiding indices, periodically migrating channels and a relatively large estuary width. The junction locations were forced by the in- and outflow locations on the sides of the ebb-tidal delta and at the location where the channel pattern transitions from multiple channels into a single channel. In the middle of the estuary, self-confinement occurred by sedimentation on the sides of the estuary, which caused another major junction. The channel orientation at the junctions steers the morphodynamics of channels and bars immediately landward and seaward, because the orientation of inflow from the ebb-tidal delta and landward river perpetually varies. In natural systems major junction locations are mostly forced by inherited geology or human engineering. However, this study concludes that even without external forcing, the estuary planform will not converge to an ideal shape but will self-confine at major junctions and widens in the adjacent zones, resulting in an irregular planform shape.

How Is Topographic Simplicity Maintained in Ephemeral, Dryland Channels?

NASA Astrophysics Data System (ADS)

Singer, M. B.; Michaelides, K.

2014-12-01

Topography in river channels reflects the time integral of streamflow-driven sediment flux mass balance. In dryland basins, infrequent and spatially heterogeneous rainfall generates a nonuniform sediment supply to ephemeral channels from hillslopes, and this sediment is subsequently sorted by spatially and temporally discontinuous channel flow. Paradoxically, the time integral of these interactions tends to produce simple topography, manifest in straight longitudinal profiles and symmetrical cross sections, which are distinct from bed morphology in perennial channels, but the controlling processes are unclear. We present a set of numerical modeling experiments based on field measurements and scenarios of uniform/nonuniform streamflow to investigate ephemeral channel bed-material flux and net sediment accumulation behavior in response to variations in channel hydrology, width, and grain size distribution. Coupled with variations in valley and channel width and frequent, yet discontinuous hillslope supply of coarse sediment, bed material becomes weakly sorted into coarse and fine sections that then affect rates of channel Qs. We identify three sediment transport thresholds relevant to poorly armored, dryland channels: 1) a low critical value required to entrain any grain sizes from the bed; 2) a value of ~4.5τ*c needed to move all grain sizes within a cross section with equal mobility; and 3) a value of ~50τ*c required to entrain gravel at nearly equivalent rates at all sections along a reach. The latter represents the 'geomorphically effective' event, which resets channel topography. We show that spatially variable flow below ~50τ*c creates and subsequently destroys incipient topography along ephemeral reaches and that large flood events above this threshold apparently dampen fluctuations in longitudinal sediment flux and thus smooth incipient channel bar forms. Both processes contribute to the maintenance of topographic simplicity in ephemeral dryland channels.

Influences of spatial and temporal variation on fish-habitat relationships defined by regression quantiles

Treesearch

Jason B. Dunham; Brian S. Cade; James W. Terrell

2002-01-01

We used regression quantiles to model potentially limiting relationships between the standing crop of cutthroat trout Oncorhynchus clarki and measures of stream channel morphology. Regression quantile models indicated that variation in fish density was inversely related to the width:depth ratio of streams but not to stream width or depth alone. The...

On the ``optimal'' spatial distribution and directional anisotropy of the filter-width and grid-resolution in large eddy simulation

NASA Astrophysics Data System (ADS)

Toosi, Siavash; Larsson, Johan

2017-11-01

The accuracy of an LES depends directly on the accuracy of the resolved part of the turbulence. The continuing increase in computational power enables the application of LES to increasingly complex flow problems for which the LES community lacks the experience of knowing what the ``optimal'' or even an ``acceptable'' grid (or equivalently filter-width distribution) is. The goal of this work is to introduce a systematic approach to finding the ``optimal'' grid/filter-width distribution and their ``optimal'' anisotropy. The method is tested first on the turbulent channel flow, mainly to see if it is able to predict the right anisotropy of the filter/grid, and then on the more complicated case of flow over a backward-facing step, to test its ability to predict the right distribution and anisotropy of the filter/grid simultaneously, hence leading to a converged solution. This work has been supported by the Naval Air Warfare Center Aircraft Division at Pax River, MD, under contract N00421132M021. Computing time has been provided by the University of Maryland supercomputing resources (http://hpcc.umd.edu).

Effects of structural parameters on fluid flow and mixing performance in a curved microchannel with gaps and baffles

NASA Astrophysics Data System (ADS)

Li, Jian; Xia, Guodong; Li, Yifan; Tian, Xinping

2013-07-01

We provide three-dimensional numerical simulations of mixing performance in a newly proposed micromixer with different structural parameters. The same amount of gaps and baffles are arranged along the curved channel within a certain distance. The effects of their structural parameters on mixing efficiency are presented, which include either the position and feature size of gaps and baffles, or the curvature radius of curved channel. The high efficiency mixing mechanism of the curved channel with gaps and baffles can attribute to the interaction of the increased contact area for premixed liquids, the jet and throttling effect over every unit of gap and baffle, the developing of the multidirectional vortices along the curved channel. The mixing index is sensitive to the width of the gaps and baffles for some Reynolds number ranges, but is not sensitive to the curvature radius of the curved channel. The characteristic of the pressure drop depending on Reynolds number is also investigated in order to keep an appropriate balance with mixing property.

Human Nav1.8: enhanced persistent and ramp currents contribute to distinct firing properties of human DRG neurons

PubMed Central

Han, Chongyang; Estacion, Mark; Huang, Jianying; Vasylyev, Dymtro; Zhao, Peng; Dib-Hajj, Sulayman D.

2015-01-01

Although species-specific differences in ion channel properties are well-documented, little has been known about the properties of the human Nav1.8 channel, an important contributor to pain signaling. Here we show, using techniques that include voltage clamp, current clamp, and dynamic clamp in dorsal root ganglion (DRG) neurons, that human Nav1.8 channels display slower inactivation kinetics and produce larger persistent current and ramp current than previously reported in other species. DRG neurons expressing human Nav1.8 channels unexpectedly produce significantly longer-lasting action potentials, including action potentials with half-widths in some cells >10 ms, and increased firing frequency compared with the narrower and usually single action potentials generated by DRG neurons expressing rat Nav1.8 channels. We also show that native human DRG neurons recapitulate these properties of Nav1.8 current and the long-lasting action potentials. Together, our results demonstrate strikingly distinct properties of human Nav1.8, which contribute to the firing properties of human DRG neurons. PMID:25787950

Human Na(v)1.8: enhanced persistent and ramp currents contribute to distinct firing properties of human DRG neurons.

PubMed

Han, Chongyang; Estacion, Mark; Huang, Jianying; Vasylyev, Dymtro; Zhao, Peng; Dib-Hajj, Sulayman D; Waxman, Stephen G

2015-05-01

Although species-specific differences in ion channel properties are well-documented, little has been known about the properties of the human Nav1.8 channel, an important contributor to pain signaling. Here we show, using techniques that include voltage clamp, current clamp, and dynamic clamp in dorsal root ganglion (DRG) neurons, that human Na(v)1.8 channels display slower inactivation kinetics and produce larger persistent current and ramp current than previously reported in other species. DRG neurons expressing human Na(v)1.8 channels unexpectedly produce significantly longer-lasting action potentials, including action potentials with half-widths in some cells >10 ms, and increased firing frequency compared with the narrower and usually single action potentials generated by DRG neurons expressing rat Na(v)1.8 channels. We also show that native human DRG neurons recapitulate these properties of Na(v)1.8 current and the long-lasting action potentials. Together, our results demonstrate strikingly distinct properties of human Na(v)1.8, which contribute to the firing properties of human DRG neurons.

Acoustic MIMO communications in a very shallow water channel

NASA Astrophysics Data System (ADS)

Zhou, Yuehai; Cao, Xiuling; Tong, Feng

2015-12-01

Underwater acoustic channels pose significant difficulty for the development of high speed communication due to highly limited band-width as well as hostile multipath interference. Enlightened by rapid progress of multiple input multiple output (MIMO) technologies in wireless communication scenarios, MIMO systems offer a potential solution by enabling multiple spatially parallel communication channels to improve communication performance as well as capacity. For MIMO acoustic communications, deep sea channels offer substantial spatial diversity among multiple channels that can be exploited to address simultaneous multipath and co-channel interference. At the same time, there are increasing requirements for high speed underwater communication in very shallow water area (for example, a depth less than 10 m). In this paper, a space-time multichannel adaptive receiver consisting of multiple decision feedback equalizers (DFE) is adopted as the receiver for a very shallow water MIMO acoustic communication system. The performance of multichannel DFE receivers with relatively small number of receiving elements are analyzed and compared with that of the multichannel time reversal receiver to evaluate the impact of limited spatial diversity on multi-channel equalization and time reversal processing. The results of sea trials in a very shallow water channel are presented to demonstrate the feasibility of very shallow water MIMO acoustic communication.

Bankfull discharge and channel characteristics of streams in New York State

USGS Publications Warehouse

Mulvihill, Christiane I.; Baldigo, Barry P.; Miller, Sarah J.; DeKoskie, Douglas; DuBois, Joel

2009-01-01

Equations that relate drainage area to bankfull discharge and channel characteristics (such as width, depth, and cross-sectional area) at gaged sites are needed to help define bankfull discharge and channel characteristics at ungaged sites and can be used in stream-restoration and protection projects, stream-channel classification, and channel assessments. These equations are intended to serve as a guide for streams in areas of similar hydrologic, climatic, and physiographic conditions. New York State contains eight hydrologic regions that were previously delineated on the basis of high-flow (flood) characteristics. This report seeks to increase understanding of the factors affecting bankfull discharge and channel characteristics to drainage-area size relations in New York State by providing an in-depth analysis of seven previously published regional bankfull-discharge and channel-characteristics curves.Stream-survey data and discharge records from 281 cross sections at 82 streamflow-gaging stations were used in regression analyses to relate drainage area to bankfull discharge and bankfull-channel width, depth, and cross-sectional area. The R2 and standard errors of estimate of each regional equation were compared to the R2 and standard errors of estimate for the statewide (pooled) model to determine if regionalizing data reduced model variability. It was found that regional models typically yield less variable results than those obtained using pooled statewide equations, which indicates statistically significant regional differences in bankfull-discharge and channel-characteristics relations.Statistical analysis of bankfull-discharge relations found that curves for regions 4 and 7 fell outside the 95-percent confidence interval bands of the statewide model and had intercepts that were significantly diferent (p≤0.10) from the other five hydrologic regions.Analysis of channel-characteristics relations found that the bankfull width, depth, and cross-sectional area curves for region 3 were significantly different p(≤0.05) from the other six regions.It was hypothesized that some regional variability could be reduced by creating models for streams with similar physiographic and climatic characteristics. Available data on streamflow patterns and previous regional-curve research suggested that mean annual runoff, Rosgen stream type, and water-surface slope were the variables most likely to influence regional bankfull discharge and channel characteristics to drainage-area size relations. Results showed that although all of these factors had an influence on regional relations, most stratified models have lower 2 values and higher standard errors of estimate than the regional models.The New York statewide (pooled) bankfull-discharge equation and equations for regions 4 and 7 were compared with equations for four other regions in the Northeast to evaluate region-to-region differences, and assess the ability of individual curves to produce results more accurate than those that would be obtained from one model of the northeastern United States. Results indicated that model slopes lack significant diferences, though intercepts are significantly different. Comparison of bankfull-discharge estimates using different models shows that results could vary by as much as 100 percent depending on which model was used and indicated that regionalization improved model accuracy.

Mixing efficiency inside micro-droplets coalesced by two components in cross-structure

NASA Astrophysics Data System (ADS)

Ren, Yanlin; Liu, Zhaomiao; Pang, Yan

2017-11-01

The mixing of micro-droplets is used in analytical chemistry, medicine production and material synthesis owing to its advantages including the encapsulation and narrow time residence distribution. In this work, droplets are coalesced by two dispersed phase with different flow rates, generated in cross-structure and mixed in planar serpentine structure. The mixing efficiency of micro-droplets under control characters including the width of entrance and the flow rate of dispersed phases have been investigated by experiments and numerical simulations. The UDS (user-defined scalar) as dimensionless concentration of the solution is adopted in simulation, and is used to calculate the concentration and the mixing effect. By changing the flow rates and the entrances` width, the changing rules of the mixing characters have been obtained. The asymmetry distributions of components make rapid mixing process in half part of each droplet when travel through a straight channel. Increasing of the ratio of entrance width result into larger droplet and weaken the chaotic mixing effect. Meanwhile, the coalesced mechanism can be performed by ranging the ratio of flow rates, the ranges are also determined by the widths of entrances. The authors gratefully acknowledge the support of National Natural Science Foundation of China (Grant No. 11572013).

Development of Relations of Stream Stage to Channel Geometry and Discharge for Stream Segments Simulated with Hydrologic Simulation Program-Fortran (HSPF), Chesapeake Bay Watershed and Adjacent Parts of Virginia, Maryland, and Delaware

USGS Publications Warehouse

Moyer, Douglas; Bennett, Mark

2007-01-01

The U.S. Geological Survey (USGS), U.S. Environmental Protection Agency (USEPA), Chesapeake Bay Program (CBP), Interstate Commission for the Potomac River Basin (ICPRB), Maryland Department of the Environment (MDE), Virginia Department of Conservation and Recreation (VADCR), and University of Maryland (UMD) are collaborating to improve the resolution of the Chesapeake Bay Regional Watershed Model (CBRWM). This watershed model uses the Hydrologic Simulation Program-Fortran (HSPF) to simulate the fate and transport of nutrients and sediment throughout the Chesapeake Bay watershed and extended areas of Virginia, Maryland, and Delaware. Information from the CBRWM is used by the CBP and other watershed managers to assess the effectiveness of water-quality improvement efforts as well as guide future management activities. A critical step in the improvement of the CBRWM framework was the development of an HSPF function table (FTABLE) for each represented stream channel. The FTABLE is used to relate stage (water depth) in a particular stream channel to associated channel surface area, channel volume, and discharge (streamflow). The primary tool used to generate an FTABLE for each stream channel is the XSECT program, a computer program that requires nine input variables used to represent channel morphology. These input variables are reach length, upstream and downstream elevation, channel bottom width, channel bankfull width, channel bankfull stage, slope of the floodplain, and Manning's roughness coefficient for the channel and floodplain. For the purpose of this study, the nine input variables were grouped into three categories: channel geometry, Manning's roughness coefficient, and channel and floodplain slope. Values of channel geometry for every stream segment represented in CBRWM were obtained by first developing regional regression models that relate basin drainage area to observed values of bankfull width, bankfull depth, and bottom width at each of the 290 USGS streamflow-gaging stations included in the areal extent of the model. These regression models were developed on the basis of data from stations in four physiographic provinces (Appalachian Plateaus, Valley and Ridge, Piedmont, and Coastal Plain) and were used to predict channel geometry for all 738 stream segments in the modeled area from associated basin drainage area. Manning's roughness coefficient for the channel and floodplain was represented in the XSECT program in two forms. First, all available field-estimated values of roughness were compiled for gaging stations in each physiographic province. The median of field-estimated values of channel and floodplain roughness for each physiographic province was applied to all respective stream segments. The second representation of Manning's roughness coefficient was to allow roughness to vary with channel depth. Roughness was estimated at each gaging station for each 1-foot depth interval. Median values of roughness were calculated for each 1-foot depth interval for all stations in each physiographic province. Channel and floodplain slope were determined for every stream segment in CBRWM using the USGS National Elevation Dataset. Function tables were generated by the XSECT program using values of channel geometry, channel and floodplain roughness, and channel and floodplain slope. The FTABLEs for each of the 290 USGS streamflow-gaging stations were evaluated by comparing observed discharge to the XSECT-derived discharge. Function table stream discharge derived using depth-varying roughness was found to be more representative of and statistically indistinguishable from values of observed stream discharge. Additionally, results of regression analysis showed that XSECT-derived discharge accounted for approximately 90 percent of the variability associated with observed discharge in each of the four physiographic provinces. The results of this study indicate that the methodology developed to generate FTABLEs for every s

75 FR 47713 - Regulated Navigation Area; Galveston Channel, TX

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-09

.... SUMMARY: The Coast Guard is establishing a regulated navigation area (RNA) across the entire width of the Galveston Channel in the vicinity of Sector Field Office (SFO) Galveston, Texas. This RNA will require... Port Houston-Galveston or a designated representative. This RNA is needed to protect the Coast Guard...

AN INTERREGIONAL COMPARISON OF CHANNEL STRUCTURE, TRANSIENT STORAGE AND NUTRIENT UPTAKE IN STREAMS DRAINING MANAGED AND OLD GROWTH WATERSHEDS

EPA Science Inventory

We compared stream channel structure (width, depth, substrate composition) and riparian canopy with transient storage and nutrient uptake in 32 streams draining old-growth and managed watersheds in the Appalachian Mountains (North Carolina), Ouachita Mountains (Arkansas), Cascade...

The influence of the macro-sediment from the mountainous area to the river morphology in Taiwan

NASA Astrophysics Data System (ADS)

Chen, S. C.; Wu, C.; Shih, P.

2012-12-01

Chen, Su-Chin scchen@nchu.edu.tw Wu, Chun-Hung* chwu@mail.nchu.edu.tw Dept. Soil & Water Conservation, National Chung Hsing University, Taichung, Taiwan. The Chenyulan River was varied changed with the marco-sediment yielded source area, Shenmu watershed, with 10 debris flow events in the last decade, in Central Taiwan. Multi-term DEMs, the measurement data of the river topographic profile and aerial photos are adopted to analyze the decade influences of the marco-sediment to the river morphology in Chenyulan River. The changes of river morphology by observing the river pattern, calculating the multi-term braided index, and estimating the distribution of sediment deposition and main channel in the river. The response for the macro-sediment from the mountainous areas into the river in the primary stage is the increase in river width, the depth of sediment deposition and volume of sediment transport. The distribution of sediment deposition from upstream landslide and river bank erosion along the river dominates the change of river morphology in the primary stage. The river morphology achieves stable gradually as the river discharge gradually decreases in the later stage. Both of the braided index and the volume of sediment transport decrease, and the river flow maintains in a main channel instead of the braided pattern in this stage. The decade sediment deposition depth is estimated as > 0.5 m, especially > 3.5 m in the sections closed to the sediment-yield source areas, the mean river width increases 15%, and the sediment with a total volume of 8×107 tons has been transported in last decade in Chenyulan River. The river morphology in Chenyulan River maintains a short-term stable, i.e. 2 or 3 years, and changes again because of the flooding events with a large amount of sediment caused by frequently heavy rainfall events in Taiwan. Furthermore, the response of river morphology in Chenyulan River due to the heavy rainfall with a total precipitation of around 860 mm in 3 days in 2009 Typhoon Morakot is also discussed in the study. A extreme river discharge with the return period of 100 year transported the macro sediment with the total volume of around 3.2×107 m3 in 8 days during 2009 Typhoon Morakot, and it also resulted in 18.1% increase of the mean river width and 4 m increase of the mean scouring depth in Chenyulan River, especially the mean increase of 50 m in river width resulted from the total sediment volume of 1.9×107 m3 deposited within 8 km from the sediment-yielded area, i.e. Shenmu watershed. Furthermore, the distribution of sediment deposition in a narrow pass is also discussed in the research. Sediment deposited apparently in the upstream of a narrow pass and also results in the disordered river patterns. The high velocity flow due to the contraction of the river width in the narrow pass section also leads to the headwater erosion in the upstream of the narrow pass section. Contrarily, the unapparent sediment deposition in the downstream of the narrow pass section brings about the stable main channel and swinging flow patterns from our decade observation.

An analytic approach to optimize tidal turbine fields

NASA Astrophysics Data System (ADS)

Pelz, P.; Metzler, M.

2013-12-01

Motivated by global warming due to CO2-emission various technologies for harvesting of energy from renewable sources are developed. Hydrokinetic turbines get applied to surface watercourse or tidal flow to gain electrical energy. Since the available power for hydrokinetic turbines is proportional to the projected cross section area, fields of turbines are installed to scale shaft power. Each hydrokinetic turbine of a field can be considered as a disk actuator. In [1], the first author derives the optimal operation point for hydropower in an open-channel. The present paper concerns about a 0-dimensional model of a disk-actuator in an open-channel flow with bypass, as a special case of [1]. Based on the energy equation, the continuity equation and the momentum balance an analytical approach is made to calculate the coefficient of performance for hydrokinetic turbines with bypass flow as function of the turbine head and the ratio of turbine width to channel width.

The respective effect of under-rib convection and pressure drop of flow fields on the performance of PEM fuel cells

PubMed Central

Wang, Chao; Zhang, Qinglei; Shen, Shuiyun; Yan, Xiaohui; Zhu, Fengjuan; Cheng, Xiaojing; Zhang, Junliang

2017-01-01

The flow field configuration plays an important role on the performance of proton exchange membrane fuel cells (PEMFCs). For instance, channel/rib width and total channel cross-sectional area determine the under-rib convection and pressure drop respectively, both of which directly influence the water removal, in turn affecting the oxygen supply and cathodic oxygen reduction reaction. In this study, effects of under-rib convection and pressure drop on cell performance are investigated experimentally and numerically by adjusting the channel/rib width and channel cross-sectional area of flow fields. The results show that the performance differences with various flow field configurations mainly derive from the oxygen transport resistance which is determined by the water accumulation degree, and the cell performance would benefit from the narrower channels and smaller cross sections. It reveals that at low current densities when water starts to accumulate in GDL at under-rib regions, the under-rib convection plays a more important role in water removal than pressure drop does; in contrast, at high current densities when water starts to accumulate in channels, the pressure drop dominates the water removal to facilitate the oxygen transport to the catalyst layer. PMID:28251983

Total ionizing dose effect in an input/output device for flash memory

NASA Astrophysics Data System (ADS)

Liu, Zhang-Li; Hu, Zhi-Yuan; Zhang, Zheng-Xuan; Shao, Hua; Chen, Ming; Bi, Da-Wei; Ning, Bing-Xu; Zou, Shi-Chang

2011-12-01

Input/output devices for flash memory are exposed to gamma ray irradiation. Total ionizing dose has been shown great influence on characteristic degradation of transistors with different sizes. In this paper, we observed a larger increase of off-state leakage in the short channel device than in long one. However, a larger threshold voltage shift is observed for the narrow width device than for the wide one, which is well known as the radiation induced narrow channel effect. The radiation induced charge in the shallow trench isolation oxide influences the electric field of the narrow channel device. Also, the drain bias dependence of the off-state leakage after irradiation is observed, which is called the radiation enhanced drain induced barrier lowing effect. Finally, we found that substrate bias voltage can suppress the off-state leakage, while leading to more obvious hump effect.

1.55 µm high speed low chirp electroabsorption modulated laser arrays based on SAG scheme.

PubMed

Cheng, Yuanbing; Wang, Qi Jie; Pan, Jiaoqing

2014-12-15

We demonstrate a cost-effective 1.55 µm low chirp 4 × 25 Gbit/s electroabsorption modulated laser (EML) array with 0.8 nm channel spacing by varying ridge width of the lasers and using selective area growth (SAG) integration scheme. The devices for all the 4 channels within the EML array show uniform threshold currents around 18 mA and high SMSRs over 45 dB. The output optical power of each channel is about 9 mW at an injection current of 100 mA. The typical chirp value of single EML measured by a fiber resonance method varied from 2.2 to -4 as the bias voltage was increased from 0 V to 2.5 V. These results show that the EML array is a suitable light source for 100 Gbit/s optical transmissions.

Fabrication and characterization of microelectromechanical systems-based gas chromatography column with embedded micro-posts for separation of environmental carcinogens.

PubMed

Sun, Jianhai; Cui, Dafu; Chen, Xing; Zhang, Lulu; Cai, Haoyuan; Li, Hui

2013-05-24

In this paper, a micro gas chromatography (μGC) column with embedded micro-posts was developed for increasing overall surface area of the columns which is able to support more of the stationary phase and reducing the effective width of the column, leading to higher separation efficiency. The proposed columns have a higher sample capacity as the overall surface area is about 3 times larger than that of open columns with the same dimensions. In order to achieve an even flow velocity in the channels, the location of the micro-posts in the linear channels and the configuration of curved channels were optimized by numerical simulation. The results have indicated that the proposed column separated 5 environmental carcinogens in less than 50s, achieved a separation efficiency of about 9500plates/m and eluted highly symmetrical Gaussian peaks. Copyright © 2013 Elsevier B.V. All rights reserved.

Morphology of the 1984 open-channel lava flow at Krafla volcano, northern Iceland

NASA Astrophysics Data System (ADS)

Rossi, Matti J.

1997-09-01

An open-channel lava flow of olivine tholeiite basalt, 9 km long and 1-2 km wide, formed in a volcanic eruption that took place in the Krafla volcano, Iceland, on the 4-18 September 1984. The eruption started with emplacement of a pahoehoe sheet which was fed by a 8.5-km-long fissure. After two days of eruption, lava effusion from the fissure ceased but one crater at the northern end of the fissure continued to release lava for another twelve days. That crater supplied an open-channel flow that moved toward the north along the rift valley. The lava was emplaced on a slope of 1°. The final lava flow is composed of five flow facies: (1) the initial pahoehoe sheet; (2) proximal slab pahoehoe and aa; (3) shelly-type overflows from the channel; (4) distal rubbly aa lava; and (5) secondary outbreaks of toothpaste lava and cauliflower aa. The main lava channel within the flow is 6.4 km long. The mean width of this channel is 189 m (103 m S.D.). An initial lava channel that forms in a Bingham plastic substance is fairly constant in width. This channel, however, varies in width especially in the proximal part indicating channel erosion. Large drifted blocks of channel walls are found throughout the flow front area and on the top of overflow levees. This suggests that the channel erosion was mainly mechanical. The lava flow has a mean height of 6 m above its surroundings, measured at the flow margins. However, a study of the pre-flow topography indicates that the lava filled a considerable topographic depression. Combined surface and pre-flow profiles give an average lava-flow thickness of 11 m; the thickness of the initial sheet-flow is estimated as 2 m. The volume of the lava flow calculated from these figures is 0.11 km 3. The mean effusion rate was 91 m 3/s. When lava flow models are used to deduce the rheological properties of this type of lava flow, the following points must be considered: (1) when a lava flow is emplaced along tectonic lineaments, its depth and volume may be significantly larger than what the surface exposure suggests; (2) lava channels may become severely eroded during channel flow even if a lava flow was formed in a relatively short time; (3) the levee dimensions, and hence lava flow dimensions, may be significantly altered by extensive overflows.

Edge-induced Schottky barrier modulation at metal contacts to exfoliated molybdenum disulfide flakes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nouchi, Ryo, E-mail: r-nouchi@21c.osakafu-u.ac.jp

2016-08-14

Ultrathin two-dimensional semiconductors obtained from layered transition-metal dichalcogenides such as molybdenum disulfide (MoS{sub 2}) are promising for ultimately scaled transistors beyond Si. Although the shortening of the semiconductor channel is widely studied, the narrowing of the channel, which should also be important for scaling down the transistor, has been examined to a lesser degree thus far. In this study, the impact of narrowing on mechanically exfoliated MoS{sub 2} flakes was investigated according to the channel-width-dependent Schottky barrier heights at Cr/Au contacts. Narrower channels were found to possess a higher Schottky barrier height, which is ascribed to the edge-induced band bendingmore » in MoS{sub 2}. The higher barrier heights degrade the transistor performance as a higher electrode-contact resistance. Theoretical analyses based on Poisson's equation showed that the edge-induced effect can be alleviated by a high dopant impurity concentration, but this strategy should be limited to channel widths of roughly 0.7 μm because of the impurity-induced charge-carrier mobility degradation. Therefore, proper termination of the dangling bonds at the edges should be necessary for aggressive scaling with layered semiconductors.« less

Boundary layer models for calving marine outlet glaciers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schoof, Christian; Davis, Andrew D.; Popa, Tiberiu V.

We consider the flow of marine-terminating outlet glaciers that are laterally confined in a channel of prescribed width. In that case, the drag exerted by the channel side walls on a floating ice shelf can reduce extensional stress at the grounding line. If ice flux through the grounding line increases with both ice thickness and extensional stress, then a longer shelf can reduce ice flux by decreasing extensional stress. Consequently, calving has an effect on flux through the grounding line by regulating the length of the shelf. In the absence of a shelf, it plays a similar role by controllingmore » the above-flotation height of the calving cliff. Using two calving laws, one due to Nick et al. (2010) based on a model for crevasse propagation due to hydrofracture and the other simply asserting that calving occurs where the glacier ice becomes afloat, we pose and analyse a flowline model for a marine-terminating glacier by two methods: direct numerical solution and matched asymptotic expansions. The latter leads to a boundary layer formulation that predicts flux through the grounding line as a function of depth to bedrock, channel width, basal drag coefficient, and a calving parameter. By contrast with unbuttressed marine ice sheets, we find that flux can decrease with increasing depth to bedrock at the grounding line, reversing the usual stability criterion for steady grounding line location. Stable steady states can then have grounding lines located on retrograde slopes. We show how this anomalous behaviour relates to the strength of lateral versus basal drag on the grounded portion of the glacier and to the specifics of the calving law used.« less

Boundary layer models for calving marine outlet glaciers

DOE PAGES

Schoof, Christian; Davis, Andrew D.; Popa, Tiberiu V.

2017-10-05

We consider the flow of marine-terminating outlet glaciers that are laterally confined in a channel of prescribed width. In that case, the drag exerted by the channel side walls on a floating ice shelf can reduce extensional stress at the grounding line. If ice flux through the grounding line increases with both ice thickness and extensional stress, then a longer shelf can reduce ice flux by decreasing extensional stress. Consequently, calving has an effect on flux through the grounding line by regulating the length of the shelf. In the absence of a shelf, it plays a similar role by controllingmore » the above-flotation height of the calving cliff. Using two calving laws, one due to Nick et al. (2010) based on a model for crevasse propagation due to hydrofracture and the other simply asserting that calving occurs where the glacier ice becomes afloat, we pose and analyse a flowline model for a marine-terminating glacier by two methods: direct numerical solution and matched asymptotic expansions. The latter leads to a boundary layer formulation that predicts flux through the grounding line as a function of depth to bedrock, channel width, basal drag coefficient, and a calving parameter. By contrast with unbuttressed marine ice sheets, we find that flux can decrease with increasing depth to bedrock at the grounding line, reversing the usual stability criterion for steady grounding line location. Stable steady states can then have grounding lines located on retrograde slopes. We show how this anomalous behaviour relates to the strength of lateral versus basal drag on the grounded portion of the glacier and to the specifics of the calving law used.« less

Response and Recovery of Streams From an Extreme Flood

NASA Astrophysics Data System (ADS)

Kantack, K. M.; Renshaw, C. E.; Magilligan, F. J.; Dethier, E.

2015-12-01

In temperate regions, channels are expected to recover from intense floods in a matter of months to years, but quantitative empirical support for this idea remains limited. Moreover, existing literature fails to address the spatial variability of the recovery process. Using an emerging technology, we investigate the immediate response to and progressive recovery of channels in the Northeastern United States from an extreme flood. We seek to determine what factors, including the nature and extent of the immediate response of the channel to the flood and post-flood availability of sediment, contribute to the spatial variability of the rate of recovery. Taking advantage of the 2011 flooding from Tropical Storm Irene, for which pre- and post-flood aerial lidar exist, along with a third set of terrestrial lidar collected in 2015, we assess channel response and recovery with multi-temporal lidar comparison. This method, with kilometers of continuous data, allows for analysis beyond traditional cross-section and reach-scale studies. Results indicate that landscape-scale factors, such as valley morphology and gradients in unit stream power, are controls on channel response to the flood, producing spatially variable impacts. Along a 16.4-km section (drainage area = 82 km2) of the Deerfield River in Vermont, over 148,000 m3 or erosion occurred during the flood. The spatial variation of impacts was correlated (R2= 0.476) with the ratio of channel width to valley width. We expect the recovery process will similarly exhibit spatial variation in rate and magnitude, possibly being governed by gradients in unit stream power and sediment availability. We test the idea that channel widening during the flood reduces post-flood unit stream power, creating a pathway for deposition and recovery to pre-flood width. Flood-widened reaches downstream of point-sources of sediment, such as landslides, will recover more quickly than those without consistent sediment supply. Results of this study will improve our ability to predict the nature and location of flood impacts and determine what factors contribute to the spatial variability of channel recovery.

Graphene Oxide: A Perfect Material for Spatial Light Modulation Based on Plasma Channels

PubMed Central

Tan, Chao; Wu, Xinghua; Wang, Qinkai; Tang, Pinghua; Shi, Xiaohui; Zhan, Shiping; Xi, Zaifang; Fu, Xiquan

2017-01-01

The graphene oxide (GO) is successfully prepared from a purified natural graphite through a pressurized oxidation method. We experimentally demonstrate that GO as an optical media can be used for spatial light modulation based on plasma channels induced by femtosecond pulses. The modulated beam exhibits good propagation properties in free space. It is easy to realize the spatial modulation on the probe beam at a high concentration of GO dispersion solutions, high power and smaller pulse width of the pump beam. We also find that the spatial modulation on the probe beam can be conveniently adjusted through the power and pulse width of pump lasers, dispersion solution concentration. PMID:28772712

Examination of Direct Discharge Measurement Data and Historic Daily Data for Selected Gages on the Middle Mississippi River, 1861-2008

USGS Publications Warehouse

Huizinga, Richard J.

2009-01-01

An examination of data from two continuous stage and discharge streamgages and one continuous stage-only gage on the Middle Mississippi River was made to determine stage-discharge relation changes through time and to investigate cause-and-effect mechanisms through evaluation of hydraulic geometry, channel elevation and water-surface elevation data. Data from discrete, direct measurements at the streamgages at St. Louis, Missouri, and Chester, Illinois, during the period of operation by the U.S. Geological Survey from 1933 to 2008 were examined for changes with time. Daily stage values from the streamgages at St. Louis (1861-2008) and Chester (1891-2008) and the stage-only gage at Cape Girardeau, Missouri (1896-2008), throughout the historic period of record also were examined for changes with time. Stage and discharge from measurements and stage-discharge relations at the streamgages at St. Louis and Chester indicate that stage for a given discharge has changed with time at both locations. An apparent increase in stage for a given discharge at increased flows (greater than flood stage) likely is caused by the raising of levees on the flood plains, and a decrease in stage for a given discharge at low flows (less than one-half flood stage) likely is caused by a combination of dikes in the channel that deepen the channel thalweg at the end of the dikes, and reduced sediment flux into the Middle Mississippi River. Since the 1960s at St. Louis, Missouri, the stage-discharge relations indicated no change or a decrease in stage for a given discharge for all discharges, whereas at Chester, Illinois, the stage-discharge relations indicate increasing stage for a given discharge above bankfull because of sediment infilling of the overflow channel. Top width and average velocity from measurements at a given discharge for the streamgage at St. Louis, Missouri, were relatively constant through time, with the only substantial change in top width resulting from the change in measurement location from the Municipal/MacArthur Bridge to the Poplar Street Bridge in 1968. The average bed elevation appeared to be lowering with time at both measurement locations at St. Louis. Flow in the Horse Island Chute overflow channel for the streamgage at Chester, Illinois had an effect on top width and average velocity from measurements, and this effect changed with time as the inflow channel to Horse Island Chute filled with sediment. Top width from measurements at a given discharge was consistent through time at the Chester streamgage when adjusted to remove the part of the flow through Horse Island Chute. Average velocity from measurements at a given discharge appears to be increasing with time, possibly as a result of a series of dikes built or extended in the channel immediately upstream from the Chester streamgage; however, the average bed elevation for all discharges less than bankfull at the Chester streamgage fluctuate around an average value from 1948 to 2000, and the fluctuations appear to be related to the occurrence of moderate and large floods. Daily stage and discharge values available for the streamgage at St. Louis, Missouri, from 1861 to 1932 display distinct, fixed relations that change slightly with time before operation by the U.S. Geological Survey, indicating daily discharge was obtained from the daily stage value during this timeframe. A sudden and substantial reduction of about 24 percent at the upper end of the ratings for discharge at a given stage occurred between 1932 and 1933 when the U.S. Geological Survey began operating the streamgage. This change likely is the result of the change to Price AA current meters from other, less-accurate methods used for discharge measurements before 1933. Based on modeling results for the Middle Mississippi River by the U.S. Army Corps of Engineers and the findings of this study, the accuracy of the historic record before 1933 is questionable, and needs to be examined further. The differ

Timeline of Intestinal Adaptation After Malabsortive Surgery: Effect of Luminal Nutrients, Biliopancreatic Secretion, and Glutamine Supplementation.

PubMed

Martínez Moreno, José Manuel; Reyes-Ortiz, Alexander; Lage Sánchez, José María; Sánchez-Gallegos, Pilar; Garcia-Caballero, Manuel

2017-12-01

The aim of this study was to study the process of intestinal adaptation in the three limbs of the small intestine after malabsorptive bariatric surgery: the biliopancreatic limb, the alimentary limb, and the common channel. These limbs are exposed to different stimuli, namely, gastrointestinal transit and nutrients in the alimentary limb, biliopancreatic secretions in the biliopancreatic limb, and a mix of both in the common channel. We also wished to investigate the effect of glutamine supplementation on the adaptation process. Three types of surgery were performed using a porcine model: biliopancreatic bypass (BPBP), massive (75%) short bowel resection as the positive control, and a sham operation (transection) as the negative control. We measured the height and width of intestinal villi, histidine decarboxylase (HDC) activity, and amount of HDC messenger RNA (mRNA) (standard diet or a diet supplemented with glutamine). An increase in HDC activity and mRNA expression was observed in the BPBP group. This increase coincided with an increase in the height and width of the intestinal villi. The increase in villus height was observed immediately after surgery and peaked at 2 weeks. Levels remained higher than those observed in sham-operated pigs for a further 4 weeks. The intestinal adaptation process in animals that underwent BPBP was less intense than in those that underwent massive short bowel resection and more intense than in those that underwent transection only. Supplementation with glutamine did not improve any of the parameters studied, although it did appear to accelerate the adaptive process.

Channel-planform evolution in four rivers of Olympic National Park, Washington, U.S.A.: The roles of physical drivers and trophic cascades

USGS Publications Warehouse

East, Amy E.; Jenkins, Kurt J.; Happe, Patricia J.; Bountry, Jennifer A.; Beechie, Timothy J.; Mastin, Mark C.; Sankey, Joel B.; Randle, Timothy J.

2017-01-01

Identifying the relative contributions of physical and ecological processes to channel evolution remains a substantial challenge in fluvial geomorphology. We use a 74-year aerial photographic record of the Hoh, Queets, Quinault, and Elwha Rivers, Olympic National Park, Washington, U.S.A., to investigate whether physical or trophic-cascade-driven ecological factors—excessive elk impacts after wolves were extirpated a century ago—are the dominant controls on channel planform of these gravel-bed rivers. We find that channel width and braiding show strong relationships with recent flood history. All four rivers have widened significantly in recent decades, consistent with increased flood activity since the 1970s. Channel planform also reflects sediment-supply changes, evident from landslide response on the Elwha River. We surmise that the Hoh River, which shows a multi-decadal trend toward greater braiding, is adjusting to increased sediment supply associated with rapid glacial retreat. In this sediment-routing system with high connectivity, such climate-driven signals appear to propagate downstream without being buffered substantially by sediment storage. Legacy effects of anthropogenic modification likely also affect the Quinault River planform. We infer no correspondence between channel geomorphic evolution and elk abundance, suggesting that trophic-cascade effects in this setting are subsidiary to physical controls on channel morphology. Our findings differ from previous interpretations of Olympic National Park fluvial dynamics and contrast with the classic example of Yellowstone National Park, where legacy effects of elk overuse are apparent in channel morphology; we attribute these differences to hydrologic regime and large-wood availability.

Evolution of geometric and hydraulic parameters as function of discharge in two streams in the National Petroleum Reserve-Alaska

NASA Astrophysics Data System (ADS)

Vas, D. A.; Toniolo, H. A.; Bailey, J.; Kemnitz, R.

2013-12-01

Abstract The National Petroleum Reserve-Alaska (NPR-A) is a vast 22.8 million acre area that extends from the foot hills of the Brooks Range to the Beaufort Sea. The United States Department of Interior, Bureau of Land Management (BLM) in association with University of Alaska Fairbanks (UAF) is conducting hydrological research to establish baseline conditions to aid future infrastructure development related to oil and gas in the NPR-A region. Field measurements (discharge, cross-sectional area, top width, water slope) were carried out in Spring 2011, 2012 and 2013, during receding water levels in the streams when the flows were ice-free. The river gauges are located approximately 15 miles south of the rivers mouth on Beaufort Sea and 13 miles from each other. The contributing watershed areas upstream of the gauging stations are 620 and 128 square miles for Judy Creek and Ublutuoch River respectively. The streams have very different channel characteristics and sediment loads. The Judy Creek channel is somewhat unstable; bed sediment contains sand and fine gravel with a heavy sediment load during spring. Bed sediment on Ublutuoch River mainly comprise of coarse gravel, with heavily brush-vegetated steep banks and very limited sediment load during spring. We present a preliminary set of hydraulic geometric relationships describing the variation of channel width, depth, and velocity as function of discharge at the gauging sites on the rivers. Empirical equations indicate that exponents for channel width have similar values in both rivers (approximately 0.38), while exponents for velocity display different values and signs. Exponents for channel depth range from 0.55 to 0.71. Differences in prevailing sediment transport conditions seem to be, at least partially, responsible for the variation in the exponents. Additionally, roughness coefficients are reported.

Migration Rate Of Tidal Meanders: Inferences From The Venice Lagoon

NASA Astrophysics Data System (ADS)

Finotello, A.; D'Alpaos, A.; Ghinassi, M.; Lanzoni, S.; Marani, M.; Rinaldo, A.

2015-12-01

Meandering channels are ubiquitous features of tidal landscapes. However, despite their fundamental role on the eco-morphodynamic evolution of these landscapes, tidal meanders have received less attention when compared to their fluvial counterparts. Improving current understanding of tidal meander migration, a largely-examined topic in fluvial landscapes, is a key step to highlight analogies and differences between tidal and fluvial cases. The migration of about 400 meander bends, belonging to 40 salt-marsh channels in the Northern Venice Lagoon (Italy), from 1968 to nowadays, has been investigated by means of both a classical method in fluvial frameworks and new procedure. Similarities with fluvial meanders occur, although important difference also emerge. Meanders cutting through the San Felice marsh follow the relationship between cartesian length and channel width, typical of meanders developed within different settings. However, meander migration rates proved to be smaller than those characterizing fluvial meanders. Indeed, the analysis of meander migration suggests a mean migration rate of about 0.10 m/year, consistent with the few data available in the literature. As for the fluvial case, the maximum-potential migration rate (i.e. the envelope curve of the relationship between migration rate and bend radius, both divided by channel width) reaches a maximum for radius-over-width ratio included between 2 and 3, regardless of the considered method. Nevertheless, the new-proposed method allows us to provide a more objective and continuous characterization. By using this new procedure, the channel curvature has finally been Fourier-analyzed, confirming the importance of even harmonics along the curvature spectrum. A correlation between migration rates and dominant harmonics seems to drive the evolution of tidal meanders and might represent a key-feature to distinguish them from their fluvial counterparts.

Classification of the alterations of beaver dams to headwater streams in northeastern Connecticut, U.S.A.

NASA Astrophysics Data System (ADS)

Burchsted, Denise; Daniels, Melinda D.

2014-01-01

Of the many types of barriers to water flow, beaver dams are among the smallest, typically lasting less than a decade and rarely exceeding 1.5 m in height. They are also among the most frequent and common obstructions in rivers, with a density often exceeding ten dams per km, a frequency of construction within a given network on a time scale of years, and a historic extent covering most of North America. Past quantification of the geomorphologic impact of beaver dams has primarily been limited to local impacts within individual impoundments and is of limited geographic scope. To assess the impact of beaver dams at larger scales, this study examines channel shape and sediment distribution in thirty river reaches in northeastern Connecticut, U.S.A. The study reaches fall within the broader categories of impounded and free-flowing segments, leaving a third segment class of beaver meadows requiring additional study. Each of the study reaches were classified at the reach scale as free-flowing, valley-wide beaver pond, in-channel beaver pond, and downstream of beaver dam. The bankfull channel width to depth ratios and channel widths normalized by watershed area vary significantly across the study reach classes. Additionally, reaches modified by beaver dams have finer sediment distributions. This paper provides the first quantitative geomorphic descriptions of the in-channel beaver pond and reaches downstream of beaver dams. Given the different channel shapes and sediment distributions, we infer that geomorphic processes are longitudinally decoupled by these frequent barriers that control local base level. These barriers generate heterogeneity within a river network by greatly increasing the range of channel morphology and by generating patches controlled by different processes. Therefore, in spite of the small size of individual beaver dams, the cumulative effect of multiple dams has the potential to modify processes at larger spatial scales. To improve assessment of the larger-scale impacts, we propose a hierarchical classification scheme based on discontinuities, place the reach classes of this study within that scheme, and suggest that further research should continue investigation of discontinuity at the network scale and quantification of the cumulative impacts.

The ‘Grand Canyon’ of the Da'an River, Taiwan - Influences on Ultra-Rapid Incision and Knickpoint Propagation

NASA Astrophysics Data System (ADS)

Cook, K. L.; Suppe, J.

2009-12-01

The 1999 magnitude 7.6 Chi-Chi earthquake resulted in significant surface uplift along the rupture zone in western Taiwan. At northeastern-most end of the rupture zone, near the town of Cholan, motion on the Chelungpu fault was accommodated by growth of the Tungshi Anticline, resulting in up to 10m of surface uplift in the channel of the Da’an River. Where the river crosses the anticline, the zone of uplift is approximately 1 km wide, with a gently sloping downstream (western) limb about 400 m long and an abrupt upstream (eastern) limb less than 50 m long. The bedrock consists of the Pliocene Cholan Formation, composed of alternating sandstone, siltstone, and mudstone beds. The bedrock is quite weak and is also pervasively fractured, making it extremely easy to erode. In response to the 1999 uplift, the Da’an River has cut a dramatic gorge, with more than 20 m of incision over a very short period. The rapid pace of incision allows us to directly observe how factors such as lithology, structure, and discharge influence the evolution of an actively incising gorge. We use a series of aerial photographs to map out the development of the gorge since 1999. We monitor the more recent evolution of the system with RTK GPS surveys to measure channel profiles, laser rangefinder measurements of channel width, and terrestrial LIDAR surveys to quantify changes in the gorge walls. The channel can currently be divided into four segments: 1) A broad network of braided alluvial channels upstream of the gorge with an average slope of 1.5 cm/km, 2) A steep knickzone about 600 m long with an average slope of 2.7 cm/km, about 8 meters of ‘excess’ incision, and abundant bedrock in the channel, 3) A lower gorge zone with low slopes, averaging between 0.6 and 1.1 cm/km, a significant amount of aggradation, and relatively narrow width, as flow is confined to the incised gorge, and 4) A broad network of braided alluvial channels downstream of the gorge with an average slope of 1.5 cm/km. The morphology of the gorge is heavily influenced by structure and lithology. Individual waterfalls within the knickzone are localized on thick beds of the more resistant sandstone, and the propagation and morphology of knickpoints have been influenced by lithologic variations and by changes in the dip of the bedding across the anticline. Steep fractures within the bedrock play a significant role in channel widening, which occurs primarily by wall collapse, particularly where the fractures dip toward the channel wall. The extremely rapid erosion rates in the gorge also provide an excellent opportunity to examine the co-evolution of channel slope and channel width in the lower section of the gorge. The presence of large amounts of bedload in the channel allow for rapid adjustment of channel slope in the wake of the knickpoint; however, the slope within the lower part of the gorge remains shallower than the reaches above and below the gorge by 0.4 to 0.9 cm/km, illustrating the influence of channel width on streampower and equilibrium slope. We expect that as the gorge continues to widen, the slopes in this segment of the gorge will steepen.

Measurement of the CP-violating phase Φ s and the B s 0 meson decay width difference with B s 0 → J/ψΦ decays in ATLAS

DOE PAGES

Aad, G.; Abbott, B.; Abdallah, J.; ...

2016-08-24

Here, a measurement of the B s 0 decay parameters in the B s 0 → J/ψΦ channel using an integrated luminosity of 14.3 fb –1 collected by the ATLAS detector from 8 TeV pp collisions at the LHC is presented. The measured parameters include the CP -violating phase Φ s, the decay width Γ s and the width difference between the mass eigenstates ΔΓ s.

Measurement of the CP-violating phase Φ s and the B s 0 meson decay width difference with B s 0 → J/ψΦ decays in ATLAS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aad, G.; Abbott, B.; Abdallah, J.

Here, a measurement of the B s 0 decay parameters in the B s 0 → J/ψΦ channel using an integrated luminosity of 14.3 fb –1 collected by the ATLAS detector from 8 TeV pp collisions at the LHC is presented. The measured parameters include the CP -violating phase Φ s, the decay width Γ s and the width difference between the mass eigenstates ΔΓ s.

Regional curve development and selection of a reference reach in the non-urban, lowland sections of the Piedmont physiographic province, Pennsylvania and Maryland

USGS Publications Warehouse

White, Kirk E.

2001-01-01

Stream-restoration projects utilizing naturalstream designs frequently are based on the bankfull- channel characteristics of a stream reach that is accommodating streamflow and sediment transport without excessive erosion or deposition. The bankfull channel is identified by the use of field indicators and confirmed with tools such as regional curves. Channel dimensions were surveyed at six streamflow-measurement stations operated by the U.S. Geological Survey in the Gettysburg-Newark Lowlands Section and Piedmont Lowlands Section of the Piedmont Physiographic Province in Pennsylvania and Maryland. Regional curves were developed from regression analyses of the relation between drainage area and cross-sectional area, mean depth, width, and streamflow of the bankfull channel. Regional curves were used to confirm the identification of the bankfull channel at a reference reach. Stream dimensions and characteristics of the reference reach were measured for extrapolation into the design of a steam-restoration project on Bermudian Creek in Adams County, Pa.Dimensions for cross-sectional area, mean depth, width, and computed streamflow of the bankfull channel in all surveyed riffle cross sections in the reference reach were within the 95-percent confidence interval bounding the regression line representing bankfull channel geometry in the Lowland Sections of the Piedmont Physiographic Province. The average bankfull cross-sectional area, bankfull mean depth, and computed bankfull discharge for riffle cross sections in the reference reach ranged from 15.4 to 16.5 percent less than estimates determined from the lowland regional curves. Average bankfull channel width was about 2 percent greater than estimates. Cross-sectional area, mean depth, and computed streamflow corresponding to the bankfull stage at the reference reach were 31.4, 44.4, and 9.6 percent less, respectively, than estimates derived from the regional curves developed by Dunne and Leopold in 1978. Average bankfull channel width at the reference reach was 16.7 percent greater than the Dunne and Leopold estimate.The concepts of regional curves and reference reaches can be valuable tools to support efforts in stream restoration. Practitioners of stream restoration need to recognize them as such and realize their limitations. The small number of stations available for analysis is a major limiting factor in the strength of the results of this investigation. Subjective selection criteria may have unnecessarily eliminated streamflow-measurement stations that could have been included in the regional curves. A bankfull discharge with a recurrence interval within the 1- to 2-year range was used as a criteria for confirmation of the bankfull stage at each streamflow-measurement station. Many researchers accept this range for recurrence interval of the bankfull discharge; however, literature provides contradictory evidence. The use of channel-characteristics data from a reference reach without any monitoring data to document the stability of the reference reach over time is a topic of debate.

Electro-optic device having a laterally varying region

NASA Technical Reports Server (NTRS)

Andrews, James T. (Inventor); Ladany, Ivan (Inventor)

1989-01-01

A distributed feedback laser comprising a semiconductor body having a channel which varies in width in the laterial direction and is periodic in the longitudinal direction. When the laser is electrically excited constructive interference of reflected light gives rise to a stable single wavelength output due to the periodic variations in the channel.

Self-Sealed Bionic Long Microchannels with Thin Walls and Designable Nanoholes Prepared by Line-Contact Capillary-Force Assembly.

PubMed

Lao, Zhao-Xin; Hu, Yan-Lei; Pan, Deng; Wang, Ren-Yan; Zhang, Chen-Chu; Ni, Jin-Cheng; Xu, Bing; Li, Jia-Wen; Wu, Dong; Chu, Jia-Ru

2017-06-01

Long microchannels with thin walls, small width, and nanoholes or irregular shaped microgaps, which are similar to capillaries or cancerous vessels, are urgently needed to simulate the physiological activities in human body. However, the fabrication of such channels remains challenging. Here, microchannels with designable holes are manufactured by combining laser printing with line-contact capillary-force assembly. Two microwalls are first printed by femtosecond laser direct-writing, and subsequently driven to collapse into a channel by the capillary force that arises in the evaporation of developer. The channel can remain stable in solvent due to the enhanced Van der Waals' force caused by the line-contact of microwalls. Microchannels with controllable nanoholes and almost arbitrary patterns can be fabricated without any bonding or multistep processes. As-prepared microchannels, with wall thicknesses less than 1 µm, widths less than 3 µm, lengths more than 1 mm, are comparable with human capillaries. In addition, the prepared channels also exhibit the ability to steer the flow of liquid without any external pump. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Wall-resolved spectral cascade-transport turbulence model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, C. S.; Shaver, D. R.; Lahey, R. T.

A spectral cascade-transport model has been developed and applied to turbulent channel flows (Reτ= 550, 950, and 2000 based on friction velocity, uτ ; or ReδΜ= 8,500; 14,800 and 31,000, based on the mean velocity and channel half-width). This model is an extension of a spectral model previously developed for homogeneous single and two-phase decay of isotropic turbulence and uniform shear flows; and a spectral turbulence model for wall-bounded flows without resolving the boundary layer. Data from direct numerical simulation (DNS) of turbulent channel flow was used to help develop this model and to assess its performance in the 1Dmore » direction across the channel width. The resultant spectral model is capable of predicting the mean velocity, turbulent kinetic energy and energy spectrum distributions for single-phase wall-bounded flows all the way to the wall, where the model source terms have been developed to account for the wall influence. We implemented the model into the 3D multiphase CFD code NPHASE-CMFD and the latest results are within reasonable error of the 1D predictions.« less

Design optimization of electric vehicle battery cooling plates for thermal performance

NASA Astrophysics Data System (ADS)

Jarrett, Anthony; Kim, Il Yong

The performance of high-energy battery cells utilized in electric vehicles (EVs) is greatly improved by adequate temperature control. An efficient thermal management system is also desirable to avoid diverting excessive power from the primary vehicle functions. In a battery cell stack, cooling can be provided by including cooling plates: thin metal fabrications which include one or more internal channels through which a coolant is pumped. Heat is conducted from the battery cells into the cooling plate, and transported away by the coolant. The operating characteristics of the cooling plate are determined in part by the geometry of the channel; its route, width, length, etc. In this study, a serpentine-channel cooling plate is modeled parametrically and its characteristics assessed using computational fluid dynamics (CFD). Objective functions of pressure drop, average temperature, and temperature uniformity are defined and numerical optimization is carried out by allowing the channel width and position to vary. The optimization results indicate that a single design can satisfy both pressure and average temperature objectives, but at the expense of temperature uniformity.

Heating element support clip

DOEpatents

Sawyer, William C.

1995-01-01

An apparatus for supporting a heating element in a channel formed in a heater base is disclosed. A preferred embodiment includes a substantially U-shaped tantalum member. The U-shape is characterized by two substantially parallel portions of tantalum that each have an end connected to opposite ends of a base portion of tantalum. The parallel portions are each substantially perpendicular to the base portion and spaced apart a distance not larger than a width of the channel and not smaller than a width of a graphite heating element. The parallel portions each have a hole therein, and the centers of the holes define an axis that is substantially parallel to the base portion. An aluminum oxide ceramic retaining pin extends through the holes in the parallel portions and into a hole in a wall of the channel to retain the U-shaped member in the channel and to support the graphite heating element. The graphite heating element is confined by the parallel portions of tantalum, the base portion of tantalum, and the retaining pin. A tantalum tube surrounds the retaining pin between the parallel portions of tantalum.

Heating element support clip

DOEpatents

Sawyer, W.C.

1995-08-15

An apparatus for supporting a heating element in a channel formed in a heater base is disclosed. A preferred embodiment includes a substantially U-shaped tantalum member. The U-shape is characterized by two substantially parallel portions of tantalum that each have an end connected to opposite ends of a base portion of tantalum. The parallel portions are each substantially perpendicular to the base portion and spaced apart a distance not larger than a width of the channel and not smaller than a width of a graphite heating element. The parallel portions each have a hole therein, and the centers of the holes define an axis that is substantially parallel to the base portion. An aluminum oxide ceramic retaining pin extends through the holes in the parallel portions and into a hole in a wall of the channel to retain the U-shaped member in the channel and to support the graphite heating element. The graphite heating element is confined by the parallel portions of tantalum, the base portion of tantalum, and the retaining pin. A tantalum tube surrounds the retaining pin between the parallel portions of tantalum. 6 figs.

Wall-resolved spectral cascade-transport turbulence model

DOE PAGES

Brown, C. S.; Shaver, D. R.; Lahey, R. T.; ...

2017-07-08

A spectral cascade-transport model has been developed and applied to turbulent channel flows (Reτ= 550, 950, and 2000 based on friction velocity, uτ ; or ReδΜ= 8,500; 14,800 and 31,000, based on the mean velocity and channel half-width). This model is an extension of a spectral model previously developed for homogeneous single and two-phase decay of isotropic turbulence and uniform shear flows; and a spectral turbulence model for wall-bounded flows without resolving the boundary layer. Data from direct numerical simulation (DNS) of turbulent channel flow was used to help develop this model and to assess its performance in the 1Dmore » direction across the channel width. The resultant spectral model is capable of predicting the mean velocity, turbulent kinetic energy and energy spectrum distributions for single-phase wall-bounded flows all the way to the wall, where the model source terms have been developed to account for the wall influence. We implemented the model into the 3D multiphase CFD code NPHASE-CMFD and the latest results are within reasonable error of the 1D predictions.« less

Fat fractal scaling of drainage networks from a random spatial network model

USGS Publications Warehouse

Karlinger, Michael R.; Troutman, Brent M.

1992-01-01

An alternative quantification of the scaling properties of river channel networks is explored using a spatial network model. Whereas scaling descriptions of drainage networks previously have been presented using a fractal analysis primarily of the channel lengths, we illustrate the scaling of the surface area of the channels defining the network pattern with an exponent which is independent of the fractal dimension but not of the fractal nature of the network. The methodology presented is a fat fractal analysis in which the drainage basin minus the channel area is considered the fat fractal. Random channel networks within a fixed basin area are generated on grids of different scales. The sample channel networks generated by the model have a common outlet of fixed width and a rule of upstream channel narrowing specified by a diameter branching exponent using hydraulic and geomorphologic principles. Scaling exponents are computed for each sample network on a given grid size and are regressed against network magnitude. Results indicate that the size of the exponents are related to magnitude of the networks and generally decrease as network magnitude increases. Cases showing differences in scaling exponents with like magnitudes suggest a direction of future work regarding other topologic basin characteristics as potential explanatory variables.

Modeled and Observed Transitions Between Rip Currents and Alongshore Flows

NASA Astrophysics Data System (ADS)

Moulton, M.; Elgar, S.; Warner, J. C.; Raubenheimer, B.

2014-12-01

Predictions of rip currents, alongshore currents, and the temporal transitions between these circulation patterns are important for swimmer safety and for estimating the transport of sediments, biota, and pollutants in the nearshore. Here, field observations are combined with hydrodynamic modeling to determine the dominant processes that lead rip currents to turn on and off with changing waves, bathymetry, and tidal elevation. Waves, currents, mean sea levels, and bathymetry were measured near and within five shore-perpendicular channels (on average 2-m deep, 30-m wide) that were dredged with the propellers of a landing craft at different times on a long straight Atlantic Ocean beach near Duck, NC in summer 2012. The circulation was measured for a range of incident wave conditions and channel sizes, and included rapid transitions between strong (0.5 to 1 m/s) rip current jets flowing offshore through the channels and alongshore currents flowing across the channels with no rip currents. Meandering alongshore currents (alongshore currents combined with an offshore jet at the downstream edge of the channel) also were observed. Circulation patterns near and within idealized rip channels simulated with COAWST (a three-dimensional phase-averaged model that couples ROMS and SWAN) are compared with the observations. In addition, the model is used to investigate the hydrodynamic response to a range of wave conditions (angle, height, period) and bathymetries (channel width, depth, and length; tidal elevations; shape of sandbar or terrace). Rip current speeds are largest for the deepest perturbations, and decrease as incident wave angles become more oblique. For obliquely incident waves, the rip currents are shifted in the direction of the alongshore flow, with an increasing shift for increasing alongshore current speed or increasing bathymetric perturbation depth.

Impact of strain on electronic and transport properties of 6 nm hydrogenated germanane nano-ribbon channel double gate field effect transistor

NASA Astrophysics Data System (ADS)

Meher Abhinav, E.; Sundararaj, Anuraj; Gopalakrishnan, Chandrasekaran; Kasmir Raja, S. V.; Chokhra, Saurabh

2017-11-01

In this work, chair like fully hydrogenated germanane (CGeH) nano-ribbon 6 nm short channel double gate field effect transistor (DG-FET) has been modeled and the impact of strain on the I-V characteristics of CGeH channel has been examined. The bond lengths, binding and formation energies of various hydrogenated geometries of buckled germanane channel were calculated using local density approximation (LDA) with Perdew-Zunger (PZ) and generalized gradient approximation (GGA) with Perdew Burke Ernzerhof (PBE) parameterization. From four various geometries, chair like structure is found to be more stable compared to boat like obtuse, stiruup structure and table like structure. The bandgap versus width, bandgap versus strain characteristics and I-V characteristics had been analyzed at room temperature using density functional theory (DFT). Using self consistent calculation it was observed that the electronic properties of nano-ribbon is independent of length and band structure, but dependent on edge type, strain [Uni-axial (ɛ xx ), bi-axial (ɛ xx   =  ɛ yy )] and width of the ribbon. The strain engineered hydrogenated germanane (GeH) showed wide direct bandgap (2.3 eV) which could help to build low noise electronic devices that operates at high frequencies. The observed bi-axial compression has high impact on the device transport characteristics with peak to valley ratio (PVR) of 2.14 and 380% increase in peak current compared to pristine CGeH device. The observed strain in CGeH DG-FET could facilitate in designing novel multiple-logic memory devices due to multiple negative differential resistance (NDR) regions.

Characterization of small microfluidic valves for studies of mechanical properties of bacteria

DOE PAGES

Yang, Da; Greer, Clayton M.; Jones, Branndon P.; ...

2015-09-02

Lab-on-a-chip platforms present many new opportunities to study bacterial cells and cellular assemblies. Here, the authors describe a new platform that allows us to apply uniaxial stress to individual bacterial cells while observing the cell and its subcellular assemblies using a high resolution optical microscope. The microfluidic chip consists of arrays of miniature pressure actuated valves. By placing a bacterium under one of such valves and partially closing the valve by externally applied pressure, the cell can be deformed. Although large pressure actuated valves used in integrated fluidic circuits have been extensively studied previously, here the authors downsize those microfluidicmore » valves and use flow channels with rectangular cross-sections to maintain the bacteria in contact with cell culture medium during the experiments. The closure of these valves has not been characterized before. First, these valves are modeled using finite element analysis, and then compared the modeling results with the actual closing profiles of the valves, which is determined from absorption measurements. The measurements and modeling show with good agreement that the deflection of valves is a linear function of externally applied pressure and the deflection scales proportionally to the width of the flow channel. In addition to characterizing the valve, the authors show at a proof-of-principle level that it can be used to deform a bacterial cell at considerable magnitude. They found the largest deformations in 5 μm wide channels where the bacterial width and length increase by 1.6 and 1.25 times, respectively. Narrower and broader channels are less optimal for these studies. Finally, the platform presents a promising approach to probe, in a quantitative and systematic way, the mechanical properties of not only bacterial cells but possibly also yeast and other single-celled organisms.« less

Effects of ultra-thin Si-fin body widths upon SOI PMOS FinFETs

NASA Astrophysics Data System (ADS)

Liaw, Yue-Gie; Chen, Chii-Wen; Liao, Wen-Shiang; Wang, Mu-Chun; Zou, Xuecheng

2018-05-01

Nano-node tri-gate FinFET devices have been developed after integrating a 14 Å nitrided gate oxide upon the silicon-on-insulator (SOI) wafers established on an advanced CMOS logic platform. These vertical double gate (FinFET) devices with ultra-thin silicon fin (Si-fin) widths ranging from 27 nm to 17 nm and gate length down to 30 nm have been successfully developed with a 193 nm scanner lithography tool. Combining the cobalt fully silicidation and the CESL strain technology beneficial for PMOS FinFETs was incorporated into this work. Detailed analyses of Id-Vg characteristics, threshold voltage (Vt), and drain-induced barrier lowering (DIBL) illustrate that the thinnest 17 nm Si-fin width FinFET exhibits the best gate controllability due to its better suppression of short channel effect (SCE). However, higher source/drain resistance (RSD), channel mobility degradation due to dry etch steps, or “current crowding effect” will slightly limit its transconductance (Gm) and drive current.

Nanostructured polymer membranes for proton conduction

DOEpatents

Balsara, Nitash Pervez; Park, Moon Jeong

2013-06-18

Polymers having an improved ability to entrain water are characterized, in some embodiments, by unusual humidity-induced phase transitions. The described polymers (e.g., hydrophilically functionalized block copolymers) have a disordered state and one or more ordered states (e.g., a lamellar state, a gyroid state, etc.). In one aspect, the polymers are capable of undergoing a disorder-to-order transition while the polymer is exposed to an increasing temperature at a constant relative humidity. In some aspects the polymer includes a plurality of portions, wherein a first portion forms proton-conductive channels within the membrane and wherein the channels have a width of less than about 6 nm. The described polymers are capable of entraining and preserving water at high temperature and low humidity. Surprisingly, in some embodiments, the polymers are capable of entraining greater amounts of water with the increase of temperature. The polymers can be used in Polymer Electrolyte Membranes in fuel cells.

Tentative Study on Performance of Darriues-Type Hydroturbine Operated in Small Open Water Channel

NASA Astrophysics Data System (ADS)

Matsushita, D.; Moriyama, R.; Nakashima, K.; Watanabe, S.; Okuma, K.; Furukawa, A.

2014-03-01

The development of small hydropower is one of the realistic and preferable utilizations of renewable energy, but the extra-low head hydropower less than 2 m is almost undeveloped yet for some reasons. The authors have developed several types of Darrieus-type hydro-turbine system, and among them, the Darrieus-turbine with a wear and a nozzle installed upstream of turbine is so far in success to obtain more output power, i.e. more shaft torque, by gathering all water into the turbine. However, there can several cases exist, in which installing the wear covering all the flow channel width is unrealistic. Then, in the present study, the hydraulic performances of Darrieus-type hydro-turbine with the inlet nozzle is investigated, putting alone in a small open channel without upstream wear. In the experiment, the five-bladed Darrieus-type runner with the pitch-circle diameter of 300 mm and the blade span of 300 mm is vertically installed in the open channel with the width of 1,200 mm. The effectiveness of the shape of the inlet nozzle is also examined using two types of two-dimensional symmetric nozzle, the straight line nozzle (SL nozzle) with the converging angle of 45 degrees and the half diameter curved nozzle (HD nozzle) whose radius is a half diameter of runner pitch circle. Inlet and outlet nozzle widths are in common for the both nozzles, which are 540 mm and 240 mm respectively. All the experiments are carried out under the conditions with constant flow rate and downstream water level, and performances are evaluated by measured output torque and the measured head difference between the water levels upstream and downstream of the turbine. As a result, it is found that the output power is remarkably increased by installing the inlet nozzle, and the turbine with SL nozzle produces larger power than that with HD nozzle. However, the peak efficiency is deteriorated in both cases. The speed ratio defined by the rotor speed divided by the downstream water velocity at the peak efficiency is larger in both cases with the inlet nozzle, partly due to the increase of inflow velocity into the turbine. In order to understand the cause of the differences of power, i.e. torque characteristics of the turbine with SL and HD nozzles, twodimensional CFD simulation is carried out. It is found that the instantaneous torque variation is important for the overall turbine performances, indicating the possibility of further performance improvement through the optimization of nozzle geometry.

Fractional channel multichannel analyzer

DOEpatents

Brackenbush, L.W.; Anderson, G.A.

1994-08-23

A multichannel analyzer incorporating the features of the present invention obtains the effect of fractional channels thus greatly reducing the number of actual channels necessary to record complex line spectra. This is accomplished by using an analog-to-digital converter in the asynchronous mode, i.e., the gate pulse from the pulse height-to-pulse width converter is not synchronized with the signal from a clock oscillator. This saves power and reduces the number of components required on the board to achieve the effect of radically expanding the number of channels without changing the circuit board. 9 figs.

Fractional channel multichannel analyzer

DOEpatents

Brackenbush, Larry W.; Anderson, Gordon A.

1994-01-01

A multichannel analyzer incorporating the features of the present invention obtains the effect of fractional channels thus greatly reducing the number of actual channels necessary to record complex line spectra. This is accomplished by using an analog-to-digital converter in the asynscronous mode, i.e., the gate pulse from the pulse height-to-pulse width converter is not synchronized with the signal from a clock oscillator. This saves power and reduces the number of components required on the board to achieve the effect of radically expanding the number of channels without changing the circuit board.

Northern/Intermountain Regions' fish habitat inventory: Grazed, rested, and ungrazed reference stream reaches, Silver King Creek, California

Treesearch

C. Kerry Overton; Gwynne L. Chandler; Janice A. Pisano

1994-01-01

Stream reaches that have been rested from livestock grazing appear to have stable banks and more bank undercuts than grazed stream sections. Ungrazed reference streams that are similar in parent geology, precipitation, channel type, habitat types, drainage area, and stream width had greater bank stability values and lower width-todepth ratios than those of grazed and...

Regional Curves of Bankfull Channel Geometry for Non-Urban Streams in the Piedmont Physiographic Province, Virginia

USGS Publications Warehouse

Lotspeich, R. Russell

2009-01-01

Natural-channel design involves constructing a stream channel with the dimensions, slope, and plan-view pattern that would be expected to transport water and sediment and yet maintain habitat and aesthetics consistent with unimpaired stream segments, or reaches. Regression relations for bankfull stream characteristics based on drainage area, referred to as 'regional curves,' are used in natural stream channel design to verify field determinations of bankfull discharge and stream channel characteristics. One-variable, ordinary least-squares regressions relating bankfull discharge, bankfull cross-sectional area, bankfull width, bankfull mean depth, and bankfull slope to drainage area were developed on the basis of data collected at 17 streamflow-gaging stations in rural areas with less than 20 percent urban land cover within the basin area (non-urban areas) of the Piedmont Physiographic Province in Virginia. These regional curves can be used to estimate the bankfull discharge and bankfull channel geometry when the drainage area of a watershed is known. Data collected included bankfull cross-sectional geometry, flood-plain geometry, and longitudinal profile data. In addition, particle-size distributions of streambed material were determined, and data on basin characteristics were compiled for each reach. Field data were analyzed to determine bankfull cross-sectional area, bankfull width, bankfull mean depth, bankfull discharge, bankfull channel slope, and D50 and D84 particle sizes at each site. The bankfull geometry from the 17 sites surveyed during this study represents the average of two riffle cross sections for each site. Regional curves developed for the 17 sites had coefficient of determination (R2) values of 0.950 for bankfull cross-sectional area, 0.913 for bankfull width, 0.915 for bankfull mean depth, 0.949 for bankfull discharge, and 0.497 for bankfull channel slope. The regional curves represent conditions for streams with defined channels and bankfull features in the Piedmont Physiographic Province in Virginia with drainage areas ranging from 0.29 to 111 square miles. All sites included in the development of the regional curves were located on streams with current or historical U.S. Geological Survey streamflow-gaging stations. These curves can be used to verify bankfull features identified in the field and bankfull stage for ungaged streams in non-urban areas.

Architecture and Channel-Belt Clustering in the Fluvial lower Wasatch Formation, Uinta Basin, Utah

NASA Astrophysics Data System (ADS)

Pisel, J. R.; Pyles, D. R.; Bracken, B.; Rosenbaum, C. D.

2013-12-01

The Eocene lower Wasatch Formation of the Uinta Basin contains exceptional outcrops of low net-sand content (27% sand) fluvial strata. This study quantitatively documents the stratigraphy of a 7 km wide by 300 meter thick strike-oriented outcrop in order to develop a quantitative data base that can be used to improve our knowledge of how some fluvial systems evolve over geologic time scales. Data used to document the outcrop are: (1) 550 meters of decimeter to half meter scale resolution stratigraphic columns that document grain size and physical sedimentary structures; (2) detailed photopanels used to document architectural style and lithofacies types in the outcrop; (3) thickness, width, and spatial position for all channel belts in the outcrop, and (4) directional measurements of paleocurrent indicators. Two channel-belt styles are recognized: lateral and downstream accreting channel belts; both of which occur as either single or multi-story. Floodplain strata are well exposed and consist of overbank fines and sand-rich crevasse splay deposits. Key upward and lateral characteristics of the outcrop documented herein are the following. First, the shapes of 243 channels are documented. The average width, thickness and aspect ratios of the channel belts are 110 m, 7 m, and 16:1, respectively. Importantly, the size and shape of channel belts does not change upward through the 300 meter transect. Second, channels are documented to spatially cluster. 9 clusters are documented using a spatial statistic. Key upward patterns in channel belt clustering are a marked change from non-amalgamated isolated channel-belt clusters to amalgamated channel-belt clusters. Critically, stratal surfaces can be correlated from mudstone units within the clusters to time-equivalent floodplain strata adjacent to the cluster demonstrating that clusters are not confined within fluvial valleys. Finally, proportions of floodplain and channel belt elements underlying clusters and channel belts vary with the style of clusters and channel belts laterally and vertically within the outcrop.

Baseline Channel Geometry and Aquatic Habitat Data for Selected Streams in the Matanuska-Susitna Valley, Alaska

USGS Publications Warehouse

Curran, Janet H.; Rice, William J.

2009-01-01

Small streams in the rapidly developing Matanuska-Susitna Valley in south-central Alaska are known to support anadromous and resident fish but little is known about their hydrologic and riparian conditions, or their sensitivity to the rapid development of the area or climate variability. To help address this need, channel geometry and aquatic habitat data were collected in 2005 as a baseline of stream conditions for selected streams. Three streams were selected as representative of various stream types, and one drainage network, the Big Lake drainage basin, was selected for a systematic assessment. Streams in the Big Lake basin were drawn in a Geographic Information System (GIS), and 55 reaches along 16 miles of Meadow Creek and its primary tributary Little Meadow Creek were identified from orthoimagery and field observations on the basis of distinctive physical and habitat parameters, most commonly gradient, substrate, and vegetation. Data-collection methods for sites at the three representative reaches and the 55 systematically studied reaches consisted of a field survey of channel and flood-plain geometry and collection of 14 habitat attributes using published protocols or slight modifications. Width/depth and entrenchment ratios along the Meadow-Little Meadow Creek corridor were large and highly variable upstream of Parks Highway and lower and more consistent downstream of Parks Highway. Channel width was strongly correlated with distance, increasing downstream in a log-linear relation. Runs formed the most common habitat type, and instream vegetation dominated the habitat cover types, which collectively covered 53 percent of the channel. Gravel suitable for spawning covered isolated areas along Meadow Creek and about 29 percent of Little Meadow Creek. Broad wetlands were common along both streams. For a comprehensive assessment of small streams in the Mat-Su Valley, critical additional data needs include hydrologic, geologic and geomorphic, and biologic data, in particular the contribution of ground water and lakes to streamflow, water quality, flood plain connectivity, and surficial geology.

8-Channel acquisition system for Time-Correlated Single-Photon Counting.

PubMed

Antonioli, S; Miari, L; Cuccato, A; Crotti, M; Rech, I; Ghioni, M

2013-06-01

Nowadays, an increasing number of applications require high-performance analytical instruments capable to detect the temporal trend of weak and fast light signals with picosecond time resolution. The Time-Correlated Single-Photon Counting (TCSPC) technique is currently one of the preferable solutions when such critical optical signals have to be analyzed and it is fully exploited in biomedical and chemical research fields, as well as in security and space applications. Recent progress in the field of single-photon detector arrays is pushing research towards the development of high performance multichannel TCSPC systems, opening the way to modern time-resolved multi-dimensional optical analysis. In this paper we describe a new 8-channel high-performance TCSPC acquisition system, designed to be compact and versatile, to be used in modern TCSPC measurement setups. We designed a novel integrated circuit including a multichannel Time-to-Amplitude Converter with variable full-scale range, a D∕A converter, and a parallel adder stage. The latter is used to adapt each converter output to the input dynamic range of a commercial 8-channel Analog-to-Digital Converter, while the integrated DAC implements the dithering technique with as small as possible area occupation. The use of this monolithic circuit made the design of a scalable system of very small dimensions (95 × 40 mm) and low power consumption (6 W) possible. Data acquired from the TCSPC measurement are digitally processed and stored inside an FPGA (Field-Programmable Gate Array), while a USB transceiver allows real-time transmission of up to eight TCSPC histograms to a remote PC. Eventually, the experimental results demonstrate that the acquisition system performs TCSPC measurements with high conversion rate (up to 5 MHz/channel), extremely low differential nonlinearity (<0.04 peak-to-peak of the time bin width), high time resolution (down to 20 ps Full-Width Half-Maximum), and very low crosstalk between channels.

Impact of Tumor Cell Cytoskeleton Organization on Invasiveness and Migration: A Microchannel-Based Approach

PubMed Central

Rolli, Claudio G.; Seufferlein, Thomas; Kemkemer, Ralf; Spatz, Joachim P.

2010-01-01

Cell migration is a fundamental feature of the interaction of cells with their surrounding. The cell's stiffness and ability to deform itself are two major characteristics that rule migration behavior especially in three-dimensional tissue. We simulate this situation making use of a micro-fabricated migration chip to test the active invasive behavior of pancreatic cancer cells (Panc-1) into narrow channels. At a channel width of 7 µm cell migration through the channels was significantly impeded due to size exclusion. A striking increase in cell invasiveness was observed once the cells were treated with the bioactive lipid sphingosylphosphorylcholine (SPC) that leads to a reorganization of the cell's keratin network, an enhancement of the cell's deformability, and also an increase in the cell's migration speed on flat surfaces. The migration speed of the highly deformed cells inside the channels was three times higher than of cells on flat substrates but was not affected upon SPC treatment. Cells inside the channels migrated predominantly by smooth sliding while maintaining constant cell length. In contrast, cells on adhesion mediating narrow lines moved in a stepwise way, characterized by fluctuations in cell length. Taken together, with our migration chip we demonstrate that the dimensionality of the environment strongly affects the migration phenotype and we suggest that the spatial cytoskeletal keratin organization correlates with the tumor cell's invasive potential. PMID:20090950

Experimental Investigation of Terminal Fans Prograding on a Salt Substrate: 3-d Physical Experiments

NASA Astrophysics Data System (ADS)

Chatmas, E.; Kim, W.

2015-12-01

Interactions between geologic features and a mobile substrate layer are present in several passive margin locations throughout the world. Deformation of a substrate layer is primarily due to differential loading of sediment and results in complexities within the morphology and subsequently the stratigraphic record. By using simplified scaled tank experiments, we investigated the relationship between substrate deformation and fan evolution in a fluvial-dump-wind-redistribution setting. In this system, sediment is being eroded from a mountain range and creating terminal fans; fluvial channels form off of the fan body and the deposited fluvial sediment is the source for an aeolian dune field. Several past experimental studies have focused on how deltas and dunes are affected on when deposited on a salt substrate, however terminal fans and channel formation off of fans have not been thoroughly investigated. The current experiments focused on which variables are the most significant in controlling fan growth, channel initiation and channel behavior on the salt substrate. Our experimental basin is 120 cm long, 60 cm wide and 30 cm tall. The materials used for a suite of five experiments involved a polymer polydimethylsiloxane (PDMS) as the deformable substrate analog and 100-μm quartz sand. By isolating certain variables such as substrate thickness, basin slope and sediment discharge we are able to see how terminal fans and channels are affected in different settings. The experimental results show that 1) increase in substrate thickness increased the amount of subsidence around the fan body, limiting sediment transport to channels off of the toe of the fan, 2) a higher basin slope increased the number of channels formed and increased sinuosity and width variations of channels over distance, and 3) a higher sediment discharge rate on a thin substrate allowed for the farthest downstream fan deposits. Preliminary results show that channel behavior and fan morphology is strongly dependent on substrate thickness and basin slope directly influences channel geometry. These findings will also be compared to the Mojave River Wash located in southern California off the San Bernardino Mountains near Zzyzx, CA to further understand the dynamics of terminal fans on a mobile substrate.

Headwater peatland channels in south-eastern Australia; the attainment of equilibrium

NASA Astrophysics Data System (ADS)

Nanson, R. A.; Cohen, T. J.

2014-05-01

Many small headwater catchments (< 50 km2) in temperate south-eastern Australia store sediment in valley fills. While accumulation in some of these systems commenced up to 30,000 years ago, most did not commence filling with peat or clastic material until at least the mid Holocene. In such headwater settings, many clastic valley fills develop cut-and-fill channels, which contrast to some peatland settings where sinuous equilibrium channels have evolved. Four peatland systems within this dataset demonstrate stable channel systems which span nearly the full spectrum of observed valley-floor slopes. We assess new and published longitudinal data from these four channels and demonstrate that each of these channels has achieved equilibrium profiles. New and published flow and survey data are synthesised to demonstrate how these peatland systems have attained equilibrium. Low rates of sediment supply and exceptionally high bank strengths have resulted in low width to depth ratios which accommodate rapid changes in flow velocity and depth with changes in discharge. In small peatland channels, planform adjustments have been sufficient to counter the energy provided by these hydraulically efficient cross-sections and have enabled the achievement of regime energy-slopes. In larger and higher energy peatland channels, large, armoured, stable, bedforms have developed. These bedforms integrate with planform adjustments to maintain a condition of minimum variance in energy losses as represented by the slope profiles and, therefore, a uniform increase in downstream entropy.

Seismic features and evolution of a late Miocene submarine channel system in the Yinggehai basin, northwestern South China Sea

NASA Astrophysics Data System (ADS)

Sun, H.; Jiang, T.; Wang, Z.; Zhang, Y.

2014-12-01

Submarine channel is one of key conduits for coarse terrigenous clastic sediments to abyssal plain, which provides the possibility for deepwater hydrocarbon exploration. Recently, a new high-quality 3D seismic data is acquired in south Yinggehai basin (YGHB) and the detailed interpretations on those seismic profiles as well as RMS amplitude attributes and variance slices reveal a submarine channel system developed in late Miocene, which could be supplied from Hainan Island via turbidity currents so that it would be filled with sand-rich turbidites as good hydrocarbon reservoir. Based on the integration between regional seismic survey and some boreholes, the investigations on its infilling architectures and depositional processes are carried out. The results show that it composes two converged submarine channels with two channelized submarine fans to their west and the main submarine channel (MSC) is characterized by a downstream increasing width and is infilled by sediments with high amplitude seismic facies, which could be originated from channelized submarine fans. Furthermore, the complicated depositional processes around the confluence region of these two channels are pointed out and the interactions between the submarine channel system and nearby channelized submarine fans are discussed. The detailed illustration on the seismic features and depositional processes of the subsurface submarine system provides us better understanding deepwater sedimentary dynamics and would be more benefit for the hydrocarbon exploration in similar deepwater area around the world.

Designing and Assessing Restored Meandering River Planform Using RVR Meander

NASA Astrophysics Data System (ADS)

Langendoen, E. J.; Abad, J. D.; Motta, D.; Frias, C. E.; Wong, M.; Barnes, B. J.; Anderson, C. D.; Garcia, M. H.; MacDonald, T. E.

2013-12-01

The ongoing modification and resulting reduction in water quality of U.S. rivers have led to a significant increase in river restoration projects over the last two decades. The increased interest in restoring degraded streams, however, has not necessarily led to improved stream function. Palmer and Allan (2005) found that many restoration projects fail to achieve their objectives due to the lack of policies to support restoration standards, to promote proven methods and to provide basic data needed for planning and implementation. Proven models of in-stream and riparian processes could be used not only to guide the design of restoration projects but also to assess both pre- and post-project indicators of ecological integrity. One of the most difficult types of river restoration projects concern reconstructing a new channel, often with an alignment and channel form different from those of the degraded pre-project channel. Recreating a meandering planform to provide longitudinal and lateral variability of flow and bed morphology to improve in-stream aquatic habitat is often desired. Channel meander planform is controlled by a multitude of variables, for example channel width to depth ratio, radius of curvature to channel width ratio, bankfull discharge, roughness, bed-material physical characteristics, bed material transport, resistance to erosion of the floodplain soils, riparian vegetation, etc. Therefore, current practices that use simple, empirically based relationships or reference reaches have led to failure in several instances, for example a washing out of meander bends or a highly unstable planform, because they fail to address the site-specific conditions. Recently, progress has been made to enhance a physically- and process-based model, RVR Meander, for rapid analysis of meandering river morphodynamics with reduced empiricism. For example, lateral migration is based on measurable physical properties of the floodplain soils and riparian vegetation versus the driving forces of the river hydrodynamics. The model can also be used in a Monte Carlo framework to statistically describe the long-term evolution of the meander planform. RVR Meander has been successfully used to evaluate migration rates of restored meandering streams and bends on the Big Sioux River, SD and Trout Creek, CA at engineering time scales. It has also been used to assess the uncertainty and risk associated with the alignment of the meandering low-flow channel of the planned diversion of the Red River of the North around the metropolitan area of Fargo, ND and Moorhead, MN. Palmer MA, Allan JD. 2005. Restoring rivers, Issues in Science and Technology, Winter 2006, Published by National Academy of Sciences, 22: 40-48.

Computational analysis of sedimentation of two particles in a narrow channel

NASA Astrophysics Data System (ADS)

Aidun, Cyrus K.; Ding, Ejiang

1998-11-01

The motion and interaction of two spherical bodies of diameter d in a narrow channel (width 4d) is simulated by Lattice-Boltzmann method at Reynolds numbers between 0 and 10. The initial positions of the particles are midway between the centerline of the channel and the side wall while one particle is 2d above the other. At low Reynolds numbers, the particles oscillate around the centerline of the channel while they approach each other, and eventually settle in contact. At higher Reynolds numbers, the trailing particle approaches the leading one; jointly, the particles enter into a damping oscillation without contacting each other. This motion has been described as drafting, kissing and tumbling (Hu, Joseph, and Crochet, Theoret. Comput. Fluid Dyn. 3 1992; Feng, Hu, and Joseph, J. Fluid Mech. 261 1994). In the phase space, constructed by the distances between each particle and the side wall, the attractor is a fixed point, representing a steady state. At even higher Reynolds number the dynamics changes into a stable limit cycle. The amplitude of the limit cycle increases as the Reynolds number increases in value. As Reynolds number increases further the motion becomes more complex. The trajectory in the phase space suggests the existence of a strange attractor. The dynamics of two particle sedimentation at this range of Reynolds number will be presented.

Stripping of acetone from water with microfabricated and membrane gas-liquid contactors.

PubMed

Constantinou, Achilleas; Ghiotto, Francesco; Lam, Koon Fung; Gavriilidis, Asterios

2014-01-07

Stripping of acetone from water utilizing nitrogen as a sweeping gas in co-current flow was conducted in a microfabricated glass/silicon gas-liquid contactor. The chip consisted of a microchannel divided into a gas and a liquid chamber by 10 μm diameter micropillars located next to one of the channel walls. The channel length was 35 mm, the channel width was 220 μm and the microchannel depth 100 μm. The micropillars were wetted by the water/acetone solution and formed a 15 μm liquid film between them and the nearest channel wall, leaving a 195 μm gap for gas flow. In addition, acetone stripping was performed in a microchannel membrane contactor, utilizing a hydrophobic PTFE membrane placed between two microstructured acrylic plates. Microchannels for gas and liquid flows were machined in the plates and had a depth of 850 μm and 200 μm respectively. In both contactors the gas/liquid interface was stabilized: in the glass/silicon contactor by the hydrophilic micropillars, while in the PTFE/acrylic one by the hydrophobic membrane. For both contactors separation efficiency was found to increase by increasing the gas/liquid flow rate ratio, but was not affected when increasing the inlet acetone concentration. Separation was more efficient in the microfabricated contactor due to the very thin liquid layer employed.

An experimental study of heat transfer enhancement in an air channel with broken multi type V-baffles

NASA Astrophysics Data System (ADS)

Kumar, Anil; Kumar, Raj; Maithani, Rajesh; Chauhan, Ranchan; Kumar, Sushil; Nadda, Rahul

2017-12-01

This work aims at studying the effect of broken multi type V-baffles on heat transfer, pressure drop, and thermal hydraulic performance characteristics in an air channel is experimentally investigated. The air channel had aspect ratio of 10.0 and the Reynolds number (Re) based upon the mass flow rate of air ( m a ) at entrance of the channel varied from 3000 to 8000. The discrete baffle distance ( D d / L v ) varied from 0.27 to 0.77, relative baffle gap width ( G w / H B ) varied from 0.50 to 1.5, relative baffle height ( H B / H D ) varied from 0.25 to 1.0, relative baffle pitch ( P B / H B ) varied from 8.0 to 12, relative baffle width ( W D / H D ) varied from 1.0 to 6.0, and flow attack angle ( α a )varied from 30° to 70°. It has been found that performance of broken multi type V-baffles air channel is better than the performance of smooth surface air channel for the range of geometrical parameters investigated. Experimental results observed that maximum enhancement in overall thermal performance have been found at Dd/Lv value of 0.67, Gw/HB value of 1.0, HB/HD value of 0.50, P B / H B value of 10, and αavalue of 60°.

33 CFR 165.703 - Tampa Bay, Florida-Safety Zone.

Code of Federal Regulations, 2013 CFR

2013-07-01

... loaded anhydrous ammonia vessel and the width of the channel in the following areas: (1) For inbound tank vessels loaded with anhydrous ammonia, Tampa Bay Cut “F” Channel from Lighted Buoys “3F” and “4F” north... anhydrous ammonia receiving terminals to Port Sutton the safety zone includes, in addition to the area in...

33 CFR 165.703 - Tampa Bay, Florida-Safety Zone.

Code of Federal Regulations, 2014 CFR

2014-07-01

... loaded anhydrous ammonia vessel and the width of the channel in the following areas: (1) For inbound tank vessels loaded with anhydrous ammonia, Tampa Bay Cut “F” Channel from Lighted Buoys “3F” and “4F” north... anhydrous ammonia receiving terminals to Port Sutton the safety zone includes, in addition to the area in...

33 CFR 165.703 - Tampa Bay, Florida-Safety Zone.

Code of Federal Regulations, 2011 CFR

2011-07-01

... loaded anhydrous ammonia vessel and the width of the channel in the following areas: (1) For inbound tank vessels loaded with anhydrous ammonia, Tampa Bay Cut “F” Channel from Lighted Buoys “3F” and “4F” north... anhydrous ammonia receiving terminals to Port Sutton the safety zone includes, in addition to the area in...

33 CFR 165.703 - Tampa Bay, Florida-Safety Zone.

Code of Federal Regulations, 2012 CFR

2012-07-01

... loaded anhydrous ammonia vessel and the width of the channel in the following areas: (1) For inbound tank vessels loaded with anhydrous ammonia, Tampa Bay Cut “F” Channel from Lighted Buoys “3F” and “4F” north... anhydrous ammonia receiving terminals to Port Sutton the safety zone includes, in addition to the area in...

33 CFR 165.703 - Tampa Bay, Florida-Safety Zone.

Code of Federal Regulations, 2010 CFR

2010-07-01

... loaded anhydrous ammonia vessel and the width of the channel in the following areas: (1) For inbound tank vessels loaded with anhydrous ammonia, Tampa Bay Cut “F” Channel from Lighted Buoys “3F” and “4F” north... anhydrous ammonia receiving terminals to Port Sutton the safety zone includes, in addition to the area in...

Patchogue River, Westbrook, Connecticut. Small Navigation Project, Detailed Project Report and Environmental Assessment.

DTIC Science & Technology

1982-12-01

Westbrook, especially if channel modifications are undertaken. Currently, local entrepreneurs are planning to construct new power- boat facilities...result. Value of Delay Time Existing S14,400 W/Plan B 7,200 PLAN B: Annual Benefit = S 7,200 PLAN C Plan C would increse the width of the existing channel

Influence of tensor interactions on masses and decay widths of dibaryons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pang Hourong; Ping Jialun; Chen Lingzhi

The influence of gluon and Goldstone boson induced tensor interactions on the dibaryon masses and D-wave decay widths has been studied in the quark delocalization, color screening model. The effective S-D wave transition interactions induced by gluon and Goldstone boson exchanges decrease rapidly with increasing strangeness of the channel. The tensor contribution of K and {eta} mesons is negligible in this model. There is no six-quark state in the light flavor world studied so far that can become bound by means of these tensor interactions besides the deuteron. The partial D-wave decay widths of the IJ{sup p}=(1/2)2{sup +}N{omega} state tomore » spin 0 and 1 {lambda}{xi} final states are 12.0 and 21.9 keV, respectively. This is a very narrow dibaryon resonance that might be detectable in those production reactions with rich high strangeness particles through the reconstruction of the vertex mass of the decay product {lambda}{xi} by existing detectors at RHIC and COMPASS at CERN or at JHF in Japan and FAIR in Germany in the future.« less

Influence of Nanopore Shapes on Thermal Conductivity of Two-Dimensional Nanoporous Material.

PubMed

Huang, Cong-Liang; Huang, Zun; Lin, Zi-Zhen; Feng, Yan-Hui; Zhang, Xin-Xin; Wang, Ge

2016-12-01

The influence of nanopore shapes on the electronic thermal conductivity (ETC) was studied in this paper. It turns out that with same porosity, the ETC will be quite different for different nanopore shapes, caused by the different channel width for different nanopore shapes. With same channel width, the influence of different nanopore shapes can be approximately omitted if the nanopore is small enough (smaller than 0.5 times EMFP in this paper). The ETC anisotropy was discovered for triangle nanopores at a large porosity with a large nanopore size, while there is a similar ETC for small pore size. It confirmed that the structure difference for small pore size may not be seen by electrons in their moving.

Using 15-minute acoustic data to analyze suspended-sediment dynamics in the Rio Grande in the Big Bend Region

USGS Publications Warehouse

Dean, David; Topping, David; Griffiths, Ronald; Sabol, Thomas; Schmidt, John C.; Bennett, Jeffery B.

2015-01-01

The Rio Grande in the Big Bend region is subject to rapid geomorphic change consisting of channel narrowing during years of low flow, and channel widening during rare, large, long duration floods. Since the 1940s, there have been large declines in mean and peak stream flow, and the channel has progressively narrowed. Large, channel widening floods are infrequent and have failed to widen the channel to widths measured prior to the onset of channel narrowing in the 1940s. Before the most recent channel-widening flood in September 2008, the Rio Grande in the Big Bend was more than 50 percent narrower than measured in the 1940s. Channel narrowing results in increased flood frequency and flood magnitude due to the loss of channel capacity and flood conveyance (Dean and Schmidt, 2011). Channel narrowing also results in the loss of important aquatic habitats such as backwaters and side-channels, because these habitats accumulate sediment and are converted to floodplains. Environmental managers are attempting to construct an environmental flow program for the purposes of minimizing channel narrowing during low flow years such that channel capacity, flood conveyance, and important aquatic habitats are maintained. Effective mitigation of channel narrowing processes requires an in-depth understanding of the predominant sediment source areas, the quantity of sediment input from those source areas, the parts of the flow regime responsible for the greatest sediment deposition, and the effect of managed flows in ameliorating the sediment loading that occurs within the channel. Here, we analyze data collected with acoustic instrumentation at high temporal resolution to quantify suspended-sediment transport during a variety of flood types. We also investigate the effect of long duration managed flows in promoting sediment export and minimizing channel narrowing.

Methamphetamine Regulation of Firing Activity of Dopamine Neurons

PubMed Central

Lin, Min; Sambo, Danielle

2016-01-01

Methamphetamine (METH) is a substrate for the dopamine transporter that increases extracellular dopamine levels by competing with dopamine uptake and increasing reverse transport of dopamine via the transporter. METH has also been shown to alter the excitability of dopamine neurons. The mechanism of METH regulation of the intrinsic firing behaviors of dopamine neurons is less understood. Here we identified an unexpected and unique property of METH on the regulation of firing activity of mouse dopamine neurons. METH produced a transient augmentation of spontaneous spike activity of midbrain dopamine neurons that was followed by a progressive reduction of spontaneous spike activity. Inspection of action potential morphology revealed that METH increased the half-width and produced larger coefficients of variation of the interspike interval, suggesting that METH exposure affected the activity of voltage-dependent potassium channels in these neurons. Since METH has been shown to affect Ca2+ homeostasis, the unexpected findings that METH broadened the action potential and decreased the amplitude of afterhyperpolarization led us to ask whether METH alters the activity of Ca2+-activated potassium (BK) channels. First, we identified BK channels in dopamine neurons by their voltage dependence and their response to a BK channel blocker or opener. While METH suppressed the amplitude of BK channel-mediated unitary currents, the BK channel opener NS1619 attenuated the effects of METH on action potential broadening, afterhyperpolarization repression, and spontaneous spike activity reduction. Live-cell total internal reflection fluorescence microscopy, electrophysiology, and biochemical analysis suggest METH exposure decreased the activity of BK channels by decreasing BK-α subunit levels at the plasma membrane. SIGNIFICANCE STATEMENT Methamphetamine (METH) competes with dopamine uptake, increases dopamine efflux via the dopamine transporter, and affects the excitability of dopamine neurons. Here, we identified an unexpected property of METH on dopamine neuron firing activity. METH transiently increased the spontaneous spike activity of dopamine neurons followed by a progressive reduction of the spontaneous spike activity. METH broadened the action potentials, increased coefficients of variation of the interspike interval, and decreased the amplitude of afterhyperpolarization, which are consistent with changes in the activity of Ca2+-activated potassium (BK) channels. We found that METH decreased the activity of BK channels by stimulating BK-α subunit trafficking. Thus, METH modulation of dopamine neurotransmission and resulting behavioral responses is, in part, due to METH regulation of BK channel activity. PMID:27707972

Sediment sorting at a side channel bifurcation

NASA Astrophysics Data System (ADS)

van Denderen, Pepijn; Schielen, Ralph; Hulscher, Suzanne

2017-04-01

Side channels have been constructed to reduce the flood risk and to increase the ecological value of the river. In various Dutch side channels large aggradation in these channels occurred after construction. Measurements show that the grain size of the deposited sediment in the side channel is smaller than the grain size found on the bed of the main channel. This suggest that sorting occurs at the bifurcation of the side channel. The objective is to reproduce with a 2D morphological model the fining of the bed in the side channel and to study the effect of the sediment sorting on morphodynamic development of the side channel. We use a 2D Delft3D model with two sediment fractions. The first fraction corresponds with the grain size that can be found on the bed of the main channel and the second fraction corresponds with the grain size found in the side channel. With the numerical model we compute several side channel configurations in which we vary the length and the width of the side channel, and the curvature of the upstream channel. From these computations we can derive the equilibrium state and the time scale of the morphodynamic development of the side channel. Preliminary results show that even when a simple sediment transport relation is used, like Engelund & Hansen, more fine sediment enters the side channel than coarse sediment. This is as expected, and is probably related to the bed slope effects which are a function of the Shields parameter. It is expected that by adding a sill at the entrance of the side channel the slope effect increases. This might reduce the amount of coarse sediment which enters the side channel even more. It is unclear whether the model used is able to reproduce the effect of such a sill correctly as modelling a sill and reproducing the correct hydrodynamic and morphodynamic behaviour is not straightforward in a 2D model. Acknowledgements: This research is funded by STW, part of the Dutch Organization for Scientific Research under grant number P12-P14 (RiverCare Perspective Programme) project number 13516.

Bone cell-materials interaction on Si microchannels with bioinert coatings.

PubMed

Condie, Russell; Bose, Susmita; Bandyopadhyay, Amit

2007-07-01

Bone implant life is dependent upon integration of biomaterial surfaces with local osteoblasts. This investigation studied the effects of various microchannel parameters and surface chemistry on immortalized osteoblast precursor cell (OPC1) adhesion. Cell-materials interactions were observed within channels of varying length, width, tortuosity, convergence, divergence and chemistry. Si wafers were used to create four distinct 1cm(2) designs of varying channel dimensions. After anisotropic chemical etching to a depth of 120microm, wafers were sputter coated with gold and titanium; and on another surface SiO(2) was grown to vary the surface chemistry of these microchannels. OPC1 cells were seeded in the central cavity of each chip before incubation in tissue culture plates. On days 5, 11 and 16, samples were taken out, fixed and processed for microscopic analysis. Samples were visually characterized, qualitatively scored and analyzed. Channel walls did not contain OPC1 migration, but showed locally interrupted adhesion. Scores for channels of floor widths as narrow as 350microm were significantly reduced. No statistically significant preference was detected for gold, titanium or SiO(2) surfaces. Bands of OPC1 cells appeared to align with nearby channels, suggesting that cell morphology may be controlled by topography of the design to improve osseointegration.

Channel widening due to urbanization and a major flood can alter bed particle organization and bed stability in an urban boulder-bed channel

NASA Astrophysics Data System (ADS)

Prestegaard, K. L.; Behrns, K.; Blanchet, Z.; Hankin, E.

2007-12-01

The Anacostia River is a tributary of the Potomac River north of Washington D.C. that has become progressively more urbanized in the past 50 years. Bankfull discharge and bankfull width in the Anacostia have increased by 3- 4x in the past 50 years. Nearby watersheds of similar size and geology, but without significant urbanization, contain threshold gravel-bed streams. The Anacostia, however, is not a threshold channel; it exhibits break-up of boulder-bed channels in upstream reaches and significant gravel bar formation in downstream reaches. These gravel bars have grown and migrated considerably in the past 10-15 years, contributing significantly to local channel widening that can be twice that of adjacent reaches. The purpose of this study is to determine bedload transport rates and grain size distributions and their relationship to discharge, bed organization and sediment supply. Bed mobility data come from both bedload transport measurements and measurements of channel bed changes. Channel bed changes were obtained from a) repeated channel cross section surveys, b) surface and subsurface size distributions, and c) bed particle organization measurements (measurements of location of particles within reaches). These measurements were made prior to and after the floods of 2006, which equalled the largest floods on record for most parts of the Anacostia River. In some boulder bed reaches, boulders were removed from the center of the channel and deposited along and on the channel banks. The mid-channel boulders were replaced by sheets of gravel and cobbles, significantly altering the bed mobility of the channels.

The natural channel of Brandywine Creek, Pennsylvania

USGS Publications Warehouse

Wolman, M.G.

1955-01-01

This study of the channel of Brandy wine Creek, Pennsylvania, consists of three parts. The first is an analysis of the changes which take place in the width, depth, velocity, slope of the water surface, suspended load, and roughness factor with changing discharge below the bankfull stage at each of several widely separated cross sections of the channel. Expressed as functions of the discharge, it is found that the variables behave systematically. In every section studied, as the discharge increases, the velocity increases to about the 0.6 power, depth to the 0.4, and load to the 2.0 power of the discharge. The roughness decreases to the 0.2 power of the discharge. The relative magnitudes and the direction of these variations are similar to those which have been observed in other rivers in the United States, primarily in the West. Some modifications of the hypotheses applicable to the western rivers are probably required because on Brandywine Creek the difference between the materials on the bed and in the banks is considerably greater than it is on most of the western rivers studied. In the second part of the paper the progressive changes of the same variables in the downstream direction with increasing discharge at a given frequency are described. Despite the disorderly appearance of the stream, it is found that the variables display a progressive, orderly change in the downstream direction when traced from the headwater tributaries through the trunk stream of Brandywine Creek. At a given frequency of flow, width increases with discharge to about the 0.5 power. Depth increases downstream somewhat less rapidly, while the slope and roughness both decrease in the downstream direction. Despite a decrease in the size of the material on the bed, both the mean velocity and the mean bed velocity increase downstream. The rates of change of these variables are in close accord with the changes observed on rivers flowing in alluvium and in stable irrigation canals. These relationships hold for all flows up to the bankfull stage. Analysis of the streamflow records indicates that the annual maximum discharge equals or exceeds the bankfull stage roughly once every 2 years. The regularity in the behavior of the variables with changing discharges both at-a-station and in the downstream direction and the similar rates of change of the variables on Brandywine Creek and in stable irrigation canals suggest the existence of a quasi-equilibrium in the channel of the creek. Part three of this study is concerned with this concept of equilibrium in streams. By analogy with canals and with several rivers in diverse regions of the United States it may be concluded that this quasi-equilibrium is closely related to the discharge, and to the concentration of the suspended load. The shape and longitudinal profile of the channel are determined by these two independent factors which operate within the limits set by the local geology. The latter determines the initial size, shape, and resistance of the material provided to the channel. The existence of a quasi-equilibrium among the variables studied suggests that most reaches on Brandywine Creek are at grade. This is true if the term "grade," when applied to natural rivers, is synonymous with quasi-equilibrium. The adjustability of the variables in the channel rather than the stability of any particular shape or longitudinal profile of the channel is emphasized when t

River meanders

USGS Publications Warehouse

Leopold, Luna Bergere; Wolman, M. Gordon

1960-01-01

Most river curves have nearly the same value of the ratio of curvature radius to channel width, in the range of 2 to 3. Meanders formed by meltwater on the surface of glaciers, and by the main current of the Gulf Stream, have a relation of meander length to channel width similar to rivers. Because such meanders carry no sediment, the shapes of curves in rivers are evidently determined primarily by the dynamics of flow rather than by relation to debris load.Velocity distributions along river curves provide a generalized picture of flow characteristics. Evidence on flow resistance in curved channels suggests that a basic aspect of meander mechanics may be related to the distribution of energy loss provided by a particular configuration or curvature. No general theory of meanders is as yet satisfactory, however; in fact, present evidence suggests that no single theory will explain the formation and characteristics of all meanders and that few of the physical principles involved have yet been clearly identified.

Ge-cap quantum-well bulk FinFET for 5 nm node CMOS integration

NASA Astrophysics Data System (ADS)

Dwi Kurniawan, Erry; Peng, Kang-Hui; Yang, Shang-Yi; Yang, Yi-Yun; Thirunavukkarasu, Vasanthan; Lin, Yu-Hsien; Wu, Yung-Chun

2018-04-01

We propose the use of Ge-cap quantum-well (QW) bulk FinFET for 5 nm CMOS integration, which is a Si channel wrapped with Ge around three sides of the fin channel. The simulation results show that the Ge-cap FinFET structure demonstrates better performance than pure Si, pure Ge, and Si-cap FinFET structures. By optimizing Si fin width and Ge-cap thickness, the on-state current of nFET and pFET can also be symmetric without changing the total fin width (F Wp = F Wn). The electrons in Ge-cap nFinFET concentrate in the Si channel because of QWs formed in the lowest conduction band of the Ge and Si heterostructure, while the holes in Ge-cap pFinFET prefer to stay in Ge surfaces owing to QWs formed in the Ge valence band. The physics studies of this device have made the design rules relevant for the application of the CMOS inverter and static random access memory (SRAM) application technology.

Characterization and prediction of meandering channel migration in the GIS environment: a case study of the Sabine River in the USA.

PubMed

Heo, Joon; Duc, Trinh Anh; Cho, Hyung-Sik; Choi, Sung-Uk

2009-05-01

This study focused on the prediction of a 22 km meandering channel migration of the Sabine River between the states of Texas and Louisiana. The meander characteristics of 12 bends, identified from seven orthophotos taken between 1974 and 2004, were acquired in a GIS environment. Based on that earlier years' data acquisition, channel prediction was performed for the two years 1996 and 2004 using least squares estimation and linear extrapolations, yielding a satisfactory agreement with the observations (the median predicted and observed migration rates were 3.1 and 3.6 [m/year], respectively). The best-predicted migration rate was found to be associated with the longest orthophoto-recorded interval. The study confirmed that channel migration is strongly correlated with bend curvature and that the maximum migration rate of the bend corresponded to a radius of curvature [bend radius (R(C))/channel width (W(C))] of 2.5. In tight bends of a smaller radius of curvature than 1.6, secondary flow scouring near the bend apex increases bend curvature. The stability index of the dimensionless bend radius was determined to be 2.45. Overall, this study proves the effectiveness of least squares estimation with historical orthophotography for characterization of meandering channel migration.

Beauty for pedestrians toy models for CP violation and baryon asymmetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lipkin, H.J.

Why are particles different from antiparticles? C and P Violation - 1956; CP Violation - 1964. Why so little new experimental information in thirty years? Where has all the antimatter gone? Toy models are presented showing: (1) How CPT and {Delta}I = 1/2 make life difficult in kaon physics by requiring equal K{sup {plus_minus}} total widths and also equal partial widths to many exclusive channels. (2) How to understand and get around CPT restrictions. (3) How CP asymmetries can occur in exclusive partial widths and still add up to equal total widths. (4) Sakharov`s 1966 scenario for how CP Violationmore » + proton decay can explain baryon asymmetry (5) How B physics can help.« less

Design considerations for large woody debris placement in stream enhancement projects. North American Journal of Fisheries Management

Treesearch

Robert H. Hilderbrand; A. Dennis Lemly; C. Andrew Dolloff; Kelly L. Harpster

1998-01-01

Log length exerted a critical influence in stabilizing large woody debris (LWD) pieces added as an experimental stream restoration technique. Logs longer than the average bank-full channel width (5.5 m) were significantly less likely to be displaced than logs shorter than this width. The longest log in stable log groups was significantly longer than the longest log in...

Breaking Through the Multi-Mesa-Channel Width Limited of Normally Off GaN HEMTs Through Modulation of the Via-Hole-Length.

PubMed

Chien, Cheng-Yen; Wu, Wen-Hsin; You, Yao-Hong; Lin, Jun-Huei; Lee, Chia-Yu; Hsu, Wen-Ching; Kuan, Chieh-Hsiung; Lin, Ray-Ming

2017-12-01

We present new normally off GaN high-electron-mobility transistors (HEMTs) that overcome the typical limitations in multi-mesa-channel (MMC) width through modulation of the via-hole-length to regulate the charge neutrality screen effect. We have prepared enhancement-mode (E-mode) GaN HEMTs having widths of up to 300 nm, based on an enhanced surface pinning effect. E-mode GaN HEMTs having MMC structures and widths as well as via-hole-lengths of 100 nm/2 μm and 300 nm/6 μm, respectively, exhibited positive threshold voltages (V th ) of 0.79 and 0.46 V, respectively. The on-resistances of the MMC and via-hole-length structures were lower than those of typical tri-gate nanoribbon GaN HEMTs. In addition, the devices not only achieved the E-mode but also improved the power performance of the GaN HEMTs and effectively mitigated the device thermal effect. We controlled the via-hole-length sidewall surface pinning effect to obtain the E-mode GaN HEMTs. Our findings suggest that via-hole-length normally off GaN HEMTs have great potential for use in next-generation power electronics.

From Fractal Trees to Deltaic Networks

NASA Astrophysics Data System (ADS)

Cazanacli, D.; Wolinsky, M. A.; Sylvester, Z.; Cantelli, A.; Paola, C.

2013-12-01

Geometric networks that capture many aspects of natural deltas can be constructed from simple concepts from graph theory and normal probability distributions. Fractal trees with symmetrical geometries are the result of replicating two simple geometric elements, line segments whose lengths decrease and bifurcation angles that are commonly held constant. Branches could also have a thickness, which in the case of natural distributary systems is the equivalent of channel width. In river- or wave-dominated natural deltas, the channel width is a function of discharge. When normal variations around the mean values for length, bifurcating angles, and discharge are applied, along with either pruning of 'clashing' branches or merging (equivalent to channel confluence), fractal trees start resembling natural deltaic networks, except that the resulting channels are unnaturally straight. Introducing a bifurcation probability fewer, naturally curved channels are obtained. If there is no bifurcation, the direction of each new segment depends on the direction the previous segment upstream (correlated random walk) and, to a lesser extent, on a general direction of growth (directional bias). When bifurcation occurs, the resulting two directions also depend on the bifurcation angle and the discharge split proportions, with the dominant branch following the direction of the upstream parent channel closely. The bifurcation probability controls the channel density and, in conjunction with the variability of the directional angles, the overall curvature of the channels. The growth of the network in effect is associated with net delta progradation. The overall shape and shape evolution of the delta depend mainly on the bifurcation angle average size and angle variability coupled with the degree of dominant direction dependency (bias). The proposed algorithm demonstrates how, based on only a few simple rules, a wide variety of channel networks resembling natural deltas, can be replicated. Network Example

Scanning gate study of organic thin-film field-effect transistor

NASA Astrophysics Data System (ADS)

Aoki, N.; Sudou, K.; Matsusaki, K.; Okamoto, K.; Ochiai, Y.

2008-03-01

Scanning gate microscopy (SGM) has been applied for a study of organic thin-film field effect transistor (OFET). In contrast to one-dimensional nano-material such a carbon nanonube or nano-structure such a quantum point contact, visualization a transport characteristic of OFET channel is basically rather difficult since the channel width is much larger than the size of the SGM tip. Nevertheless, Schottky barriers are successfully visualized at the boundary between the metal electrodes and the OFET channel at ambient atmosphere.

Photoproduction of the f1(1285 ) meson

NASA Astrophysics Data System (ADS)

Dickson, R.; Schumacher, R. A.; Adhikari, K. P.; Akbar, Z.; Amaryan, M. J.; Anefalos Pereira, S.; Badui, R. A.; Ball, J.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A.; Boiarinov, S.; Briscoe, W. J.; Burkert, V. D.; Cao, T.; Carman, D. S.; Celentano, A.; Chandavar, S.; Charles, G.; Chetry, T.; Ciullo, G.; Colaneri, L.; Cole, P. L.; Compton, N.; Contalbrigo, M.; Cortes, O.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Deur, A.; Djalali, C.; Dugger, M.; Dupre, R.; El Alaoui, A.; El Fassi, L.; Eugenio, P.; Fanchini, E.; Fedotov, G.; Filippi, A.; Fleming, J. A.; Gevorgyan, N.; Ghandilyan, Y.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Gothe, R. W.; Griffioen, K. A.; Guo, L.; Hafidi, K.; Hakobyan, H.; Hanretty, C.; Harrison, N.; Hattawy, M.; Holtrop, M.; Hicks, K.; Hughes, S. M.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Isupov, E. L.; Jiang, H.; Jo, H. S.; Joosten, S.; Keller, D.; Khachatryan, G.; Khandaker, M.; Kim, A.; Kim, W.; Klein, F. J.; Kubarovsky, V.; Kuleshov, S. V.; Lanza, L.; Lenisa, P.; Livingston, K.; Lu, H. Y.; MacGregor, I. J. D.; Mattione, P.; McKinnon, B.; Meyer, C. A.; Mirazita, M.; Markov, N.; Mokeev, V.; Moriya, K.; Munevar, E.; Murdoch, G.; Nadel-Turonski, P.; Net, L. A.; Ni, A.; Osipenko, M.; Ostrovidov, A. I.; Park, K.; Pasyuk, E.; Phelps, W.; Pisano, S.; Pogorelko, O.; Price, J. W.; Prok, Y.; Puckett, A. J. R.; Raue, B. A.; Ripani, M.; Rizzo, A.; Rosner, G.; Roy, P.; Salgado, C.; Seder, E.; Sharabian, Y. G.; Skorodumina, Iu.; Smith, E. S.; Smith, G. D.; Sober, D.; Sokhan, D.; Sparveris, N.; Stepanyan, S.; Strakovsky, I. I.; Stankovic, I.; Strauch, S.; Sytnik, V.; Taiuti, M.; Ungaro, M.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Watts, D. P.; Weygand, D.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zonta, I.; CLAS Collaboration

2016-06-01

The f1(1285 ) meson with mass 1281.0 ±0.8 MeV/c2 and width 18.4 ±1.4 MeV (full width at half maximum) was measured for the first time in photoproduction from a proton target using CLAS at Jefferson Lab. Differential cross sections were obtained via the η π+π-,K+K¯0π- , and K-K0π+ decay channels from threshold up to a center-of-mass energy of 2.8 GeV. The mass, width, and an amplitude analysis of the η π+π- final-state Dalitz distribution are consistent with the axial-vector JP=1+ f1(1285 ) identity, rather than the pseudoscalar 0- η (1295 ) . The production mechanism is more consistent with s -channel decay of a high-mass N* state and not with t -channel meson exchange. Decays to η π π go dominantly via the intermediate a0±(980 ) π∓ states, with the branching ratio Γ [a0π (noK ¯K )] /Γ [η π π (all)] =0.74 ±0.09 . The branching ratios Γ (K K ¯π ) /Γ (η π π ) =0.216 ±0.033 and Γ (γ ρ0) /Γ (η π π ) =0.047 ±0.018 were also obtained. The first is in agreement with previous data for the f1(1285 ) , while the latter is lower than the world average.

Historical and simulated changes in channel characteristics of the Kalamazoo River, Plainwell to Otesgo, Michigan

USGS Publications Warehouse

Rachol, Cynthia M.; Fitzpatrick, Faith A.; Rossi, Tiffiny

2005-01-01

In a study to understand the historical effects of the construction and decommissioning of dams on the Kalamazoo River, Plainwell to Otesgo, Michigan, and to simulate channel changes that may result if the dams were removed, early to mid-1800s General Land Office surveys and aerial photographs from 1938, 1981, and 1999 were compared in order to identify historical changes in the river’s planform. This analysis of the 80-mile reach from Morrow Dam to the river mouth at Saugatuck provided insight into how susceptible the river has been to channel migration. The comparison showed that changes in channel width and location were caused mainly by construction of dams and subsequent water-level adjustments in the impounded reaches upstream from the dams. Braiding also occurred downstream from one of the dams. Minor changes in channel form that were not caused by the dams, such as the development and cutoff of meander bends, were observed. A more detailed study in a 5-mile reach passing through the Plainwell and Otsego City Dams included compiling existing valley cross section and longitudinal profile data into a database, assessing bank stability, and using a hydrologic model to simulate the channel as if the dams were removed. Fifty-four valley cross sections compiled from United States Geological Survey and consultant data sets were used as a base for a bank-stability assessment and to design a hypothetical stable channel without the two dams. The channel design involved adjusting the slope, hydraulic geometry, and floodplain width to ensure that water could be transferred through the reach without increasing flooding or erosion problems. The bank-stability assessment focused on conditions that are critical to failure. This was accomplished through the use of a two step process. The first involved evaluating the sediment removed from the bank toe when the stage is high. The second involved calculating the factor of safety for the bank based on the water table being elevated higher than the stage, mimicing a bank storage effect. Using these paired proccesses, two scenarios of critical conditions were evaluated: dams present and dams removed. Results of the bank assessments showed that, under both critical-condition scenarios, the streambanks were more susceptible to toe erosion than to block failure. As toe erosion progresses, the banks will eventually collapse as supporting material underneath is removed. Toe erosion for the damsremoved scenario resulted in higher amounts of erosion than for the dams-present scenario, leading to an overall decrease in bank stability. Effects of vegetation on the bank stability were variable; stability for some banks increase if vegetation was present but remain the same for other banks.

Turbine component cooling channel mesh with intersection chambers

DOEpatents

Lee, Ching-Pang; Marra, John J

2014-05-06

A mesh (35) of cooling channels (35A, 35B) with an array of cooling channel intersections (42) in a wall (21, 22) of a turbine component. A mixing chamber (42A-C) at each intersection is wider (W1, W2)) than a width (W) of each of the cooling channels connected to the mixing chamber. The mixing chamber promotes swirl, and slows the coolant for more efficient and uniform cooling. A series of cooling meshes (M1, M2) may be separated by mixing manifolds (44), which may have film cooling holes (46) and/or coolant refresher holes (48).

Rapid and efficient mixing in a slip-driven three-dimensional flow in a rectangular channel

NASA Astrophysics Data System (ADS)

Pacheco, J. Rafael; Ping Chen, Kang; Hayes, Mark A.

2006-08-01

A method for generating mixing in an electroosmotic flow of an electrolytic solution in a three-dimensional channel is proposed. When the width-to-height aspect ratio of the channel cross-section is large, mixing of a blob of a solute in a slip-driven three-dimensional flow in a rectangular channel can be used to model and assess the effectiveness of this method. It is demonstrated through numerical simulations that under certain operating conditions, rapid and efficient mixing can be achieved. Future investigation will include the solution of the exact equations and experimentation.

Qualitative evaluation of rock weir field performance and failure mechanisms

USGS Publications Warehouse

Mooney, David M.; Holmquist-Johnson, Christopher L.; Holburn, Elaina

2007-01-01

River spanning loose-rock structures provide sufficient head for irrigation diversion, permit fish passage over barriers, protect banks, stabilize degrading channels, activate side channels, reconnect floodplains, and create in-channel habitat. These structures are called by a variety of names including rock weirs, alphabet (U-, A-, V-, W-) weirs, Jhooks, and rock ramps. These structures share the common characteristics of:Loose rock construction materials (individually placed or dumped rocks with little or no concrete);Extents spanning the width of the river channel; andAn abrupt change in the water surface elevation at low flows.

Regionalized equations for bankfull-discharge and channel characteristics of streams in New York State—Hydrologic Region 5 in central New York

USGS Publications Warehouse

Westergard, Britt E.; Mulvihill, Christiane I.; Ernst, Anne G.; Baldigo, Barry P.

2005-01-01

Equations that relate drainage area to bankfull discharge and channel dimensions (width, depth, and cross-sectional area) at gaged sites are needed to define bankfull discharge and channel dimensions at ungaged sites and to provide information for the design of stream-restoration projects. Such equations are most accurate if derived from streams within an area of uniform hydrologic, climatic, and physiographic conditions and applied only within that region. A study to develop equations to predict bankfull data for ungaged streams in New York established eight regions that coincided with previously defined hydrologic regions. This report presents drainage areas and bankfull characteristics (discharge and channel dimensions) for streams in central New York (Region 5) selected for this pilot study.Stream-survey data and discharge records from seven active (currently gaged) sites and nine inactive (discontinued gaged) sites were used in regression analyses to relate size of drainage area to bankfull discharge and bankfull channel width, depth, and cross-sectional area. The resulting equations are:(1) bankfull discharge, in cubic feet per second = 45.3*(drainage area, in square miles)0.856;(2) bankfull channel width, in feet = 13.5*(drainage area, in square miles)0.449;(3) bankfull channel depth, in feet = 0.801*(drainage area, in square miles)0.373; and(4) bankfull channel cross-sectional area, in square feet = 10.8*(drainage area, in square miles)0.823.The high correlation coefficients (R2) for these four equations (0.96, 0.92, 0.91, 0.98, respectively) indicate that much of the variation in the variables is explained by the size of the drainage area. Recurrence intervals for the estimated bankfull discharge of each stream ranged from 1.11 to 3.40 years; the mean recurrence interval was 1.51 years. The 16 surveyed streams were classified by Rosgen stream type; most were mainly C-type reaches, with occasional B- and F-type reaches. The Region 5 equation was compared with equations developed for six other large areas in the Northeast. The major differences among results indicate a need to refine equations so they can be applied by water-resources managers to local planning and design efforts.

Enhanced sheet carrier densities in polarization controlled AlInN/AlN/GaN/InGaN field-effect transistor on Si (111)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hennig, J., E-mail: jonas.hennig@ovgu.de; Dadgar, A.; Witte, H.

2015-07-15

We report on GaN based field-effect transistor (FET) structures exhibiting sheet carrier densities of n = 2.9 10{sup 13} cm{sup −2} for high-power transistor applications. By grading the indium-content of InGaN layers grown prior to a conventional GaN/AlN/AlInN FET structure control of the channel width at the GaN/AlN interface is obtained. The composition of the InGaN layer was graded from nominally x{sub In} = 30 % to pure GaN just below the AlN/AlInN interface. Simulations reveal the impact of the additional InGaN layer on the potential well width which controls the sheet carrier density within the channel region of the devices.more » Benchmarking the In{sub x}Ga{sub 1−x}N/GaN/AlN/Al{sub 0.87}In{sub 0.13}N based FETs against GaN/AlN/AlInN FET reference structures we found increased maximum current densities of I{sub SD} = 1300 mA/mm (560 mA/mm). In addition, the InGaN layer helps to achieve broader transconductance profiles as well as reduced leakage currents.« less

A landscape perspective on bat foraging ecology along rivers: does channel confinement and insect availability influence the response of bats to aquatic resources in riverine landscapes?

PubMed

Hagen, Elizabeth M; Sabo, John L

2011-07-01

River and riparian areas provide an important foraging habitat for insectivorous bats owing to high insect availability along waterways. However, structural characteristics of the riverine landscape may also influence the location of foraging bats. We used bat detectors to compare bat activity longitudinally along river reaches with contrasting channel confinement, ratio of valley floor width to active channel width, and riparian vegetation, and laterally with distance from the river along three different reach types. We measured rates of insect emergence from the river and aerial insect availability above the river and laterally up to 50-m into the riparian habitat in order to assess the relationship between food resources and insectivorous bat activity. Longitudinally, bat activity was concentrated along confined reaches in comparison to unconfined reaches but was not related to insect availability. Laterally, bats tracked exponential declines in aquatic insects with distance from the river. These data suggest that along the lateral dimension bats track food resources, but that along the longitudinal dimension channel shape and landscape structure determine bat distributions more than food resources.

Lithologic controls on valley width and strath terrace formation

NASA Astrophysics Data System (ADS)

Schanz, Sarah A.; Montgomery, David R.

2016-04-01

Valley width and the degree of bedrock river terrace development vary with lithology in the Willapa and Nehalem river basins, Pacific Northwest, USA. Here, we present field-based evidence for the mechanisms by which lithology controls floodplain width and bedrock terrace formation in erosion-resistant and easily friable lithologies. We mapped valley surfaces in both basins, dated straths using radiocarbon, compared valley width versus drainage area for basalt and sedimentary bedrock valleys, and constructed slope-area plots. In the friable sedimentary bedrock, valleys are 2 to 3 times wider, host flights of strath terraces, and have concavity values near 1; whereas the erosion-resistant basalt bedrock forms narrow valleys with poorly developed, localized, or no bedrock terraces and a channel steepness index half that of the friable bedrock and an average channel concavity of about 0.5. The oldest dated strath terrace on the Willapa River, T2, was active for nearly 10,000 years, from 11,265 to 2862 calibrated years before present (cal YBP), whereas the youngest terrace, T1, is Anthropocene in age and recently abandoned. Incision rates derived from terrace ages average 0.32 mm y- 1 for T2 and 11.47 mm y- 1 for T1. Our results indicate bedrock weathering properties influence valley width through the creation of a dense fracture network in the friable bedrock that results in high rates of lateral erosion of exposed bedrock banks. Conversely, the erosion-resistant bedrock has concavity values more typical of detachment-limited streams, exhibits a sparse fracture network, and displays evidence for infrequent episodic block erosion and plucking. Lithology thereby plays a direct role on the rates of lateral erosion, influencing valley width and the potential for strath terrace planation and preservation.

Ponding, draining and tilting of the Cerberus Plains; a cryolacustrine origin for the sinuous ridge and channel networks in Rahway Vallis, Mars

NASA Astrophysics Data System (ADS)

Ramsdale, J. D.; Balme, M. R.; Conway, S. J.; Gallagher, C.

2015-06-01

Rahway Vallis sits within a shallow basin (the "Rahway basin") in the Cerberus Plains of Mars containing a branching network of channels converging on the basin floor. Using topographic cross-profiles of the channels we have found that they are set within broader, subtly-expressed, valleys. These valleys are shallow (around 15 m vertically compared to several kilometres in the horizontal) and have convex to rectilinear slope profiles that are consistent in form across the whole Rahway basin. Both channels and valleys descend and deepen consistently from west to east. The channels typically widen down-slope and increase in width at confluences. The morphology and topology of this channel system are consistent with formation by contributory fluid flow, generated from many distributed sources. The transition between the older heavily cratered terrain and the floor of the Rahway basin is bounded by near-horizontal continuous topographic terraces. Plotting the elevation of the terraces shows that they conform to a plane with a height difference of around 100 m east to west for the 300 km width of the Rahway basin. We calculate that the volume of material needed to fill the topography up to the level of the plane best fit by the terraces is ∼1500 km3. Bordering the channels are sinuous ridges, typically several kilometres long, 20 m across, with heights on the order of 10 m. They sometimes form branching networks leading into the channels, but also occur individually and parallel to the channels. The multiple tilted terraces, the channel/valley network with many fluvial-like characteristics, and the distributed source regions, suggest that the landforms within the Rahway basin are unlikely to have formed through purely volcanic processes. Rather, the channels within the Rahway basin are consistent with a genesis requiring the flow of liquid water, and the sinuous ridges with melting of a static ice body that occupied the basin. We suggest a hypothesis of rapid basin filling by fluvial flooding, followed by lake drainage. Drainage could have occurred as a consequence of an ice or debris-dam failure within (or during the formation of) the large, nearby fluvial flood channel Marte Vallis. If the lake was partly or largely frozen prior to drainage, this offers a possible explanation for the sinuous ridge systems. Hence, although the sinuous ridges provide some of the most compelling morphological analogues of terrestrial eskers yet observed, we conclude that the contextual evidence for this interpretation in Rahway Vallis is not strong, and instead they are better explained in the context of a frozen or partially frozen lake or cryolacustrine model.

Effects of natural-channel-design restoration on habitat quality in Catskill Mountain streams, New York

USGS Publications Warehouse

Ernst, Anne G.; Baldigo, Barry P.; Mulvihill, Christiane; Vian, Mark

2010-01-01

Stream restoration has received much attention in recent years, yet there has been little effort to evaluate its impacts on physical habitat, stability, and biota. A popular but controversial stream restoration approach is natural channel design (NCD), which cannot be adequately evaluated without a long-term, independent assessment of its effects on stream habitat. Six reaches of five Catskill Mountain streams in southeastern New York were restored during 2000–2003 following NCD techniques to decrease bed and bank degradation, decrease sediment loads, and improve water quality. Habitat surveys were conducted during summer low flows from 2001 to 2007. The effects of the NCD projects on stream condition were assessed via a before–after–control–impact study design to quantify the net changes in stream and bank habitat variables relative to those in unaltered control reaches. Analysis of variance tests of three different measures of bank stability show that on average stream stability increased at treatment sites for 2–5 years after restoration. Mean channel depth, thalweg depth, and the pool–riffle ratio generally increased, whereas mean channel width, percent streambank coverage by trees, and shade decreased. Habitat suitability indices for local salmonid species increased at four of six reaches after restoration. The changes in channel dimensions rendered them generally more characteristic of stabler stream forms in the given valley settings. Although these studies were done relatively soon after project completion, our findings demonstrate that habitat conditions can be improved in degraded Catskill Mountain streams through NCD restoration.

Functional polymer sheet patterning using microfluidics.

PubMed

Li, Minggan; Humayun, Mouhita; Kozinski, Janusz A; Hwang, Dae Kun

2014-07-22

Poly(dimethylsiloxane) (PDMS)-based microfluidics provide a novel approach to advanced material synthesis. While PDMS has been successfully used in a wide range of industrial applications, due to the weak mechanical property channels generally possess low aspect ratios (AR) and thus produce microparticles with similarly low ARs. By increasing the channel width to nearly 1 cm, AR to 267, and implementing flow lithography, we were able to establish the slit-channel lithography. Not only does this allow us to synthesize sheet materials bearing multiscale features and tunable chemical anisotropy but it also allows us to fabricate functional layered sheet structures in a one-step, high-throughput fashion. We showcased the technique's potential role in various applications, such as the synthesis of planar material with micro- and nanoscale features, surface morphologies, construction of tubular and 3D layered hydrogel tissue scaffolds, and one-step formation of radio frequency identification (RFID) tags. The method introduced offers a novel route to functional sheet material synthesis and sheet system fabrication.

Electrical characterization of vertically stacked p-FET SOI nanowires

NASA Astrophysics Data System (ADS)

Cardoso Paz, Bruna; Cassé, Mikaël; Barraud, Sylvain; Reimbold, Gilles; Vinet, Maud; Faynot, Olivier; Antonio Pavanello, Marcelo

2018-03-01

This work presents the performance and transport characteristics of vertically stacked p-type MOSFET SOI nanowires (NWs) with inner spacers and epitaxial growth of SiGe raised source/drain. The conventional procedure to extract the effective oxide thickness (EOT) and Shift and Ratio Method (S&R) have been adapted and validated through tridimensional numerical simulations. Electrical characterization is performed for NWs with [1 1 0]- and [1 0 0]-oriented channels, as a function of both fin width (WFIN) and channel length (L). Results show a good electrostatic control and reduced short channel effects (SCE) down to 15 nm gate length, for both orientations. Effective mobility is found around two times higher for [1 1 0]- in comparison to [1 0 0]-oriented NWs due to higher holes mobility contribution in (1 1 0) plan. Improvements obtained on ION/IOFF by reducing WFIN are mainly due to subthreshold slope decrease, once small and none mobility increase is obtained for [1 1 0]- and [1 0 0]-oriented NWs, respectively.

Study of radially excited Ds(21 S 0) and Ds(3P)

NASA Astrophysics Data System (ADS)

Tian, Yu; Zhao, Ze; Zhang, Ai-Lin

2017-08-01

The unobserved JP = 0- radial excitation Ds(21 S 0) is anticipated to have mass 2650 MeV (denoted as Ds(2650)). Study of hadronic production is an important way to identify highly excited states. We study hadronic production of Ds(2650) from higher excited resonances in a 3 P 0 model. Relevant hadronic partial decay widths are found to be very small, which implies it is difficult to observe Ds(2650) in hadronic decays of higher excited resonances. Hadronic decay widths of radially excited Ds(3P) have also been estimated. The total decay widths of four Ds(3P) are large, but the branching ratios in the Ds(2650)η channel are very small, which implies that it seems impossible to observe Ds(2650) in hadronic decays of Ds(3P). The dominant decay channels of the four Ds(3P) have been pointed out, and D1(2420), D1(2430), , D(2550), D(2600), (11D2)D(2750) and are possible to observe in hadronic production from Ds(3P). Supported by National Natural Science Foundation of China (11475111)

Spider web-structured labyrinthine acoustic metamaterials for low-frequency sound control

NASA Astrophysics Data System (ADS)

Krushynska, A. O.; Bosia, F.; Miniaci, M.; Pugno, N. M.

2017-10-01

Attenuating low-frequency sound remains a challenge, despite many advances in this field. Recently-developed acoustic metamaterials are characterized by unusual wave manipulation abilities that make them ideal candidates for efficient subwavelength sound control. In particular, labyrinthine acoustic metamaterials exhibit extremely high wave reflectivity, conical dispersion, and multiple artificial resonant modes originating from the specifically-designed topological architectures. These features enable broadband sound attenuation, negative refraction, acoustic cloaking and other peculiar effects. However, hybrid and/or tunable metamaterial performance implying enhanced wave reflection and simultaneous presence of conical dispersion at desired frequencies has not been reported so far. In this paper, we propose a new type of labyrinthine acoustic metamaterials (LAMMs) with hybrid dispersion characteristics by exploiting spider web-structured configurations. The developed design approach consists in adding a square surrounding frame to sectorial circular-shaped labyrinthine channels described in previous publications (e.g. (11)). Despite its simplicity, this approach provides tunability in the metamaterial functionality, such as the activation/elimination of subwavelength band gaps and negative group-velocity modes by increasing/decreasing the edge cavity dimensions. Since these cavities can be treated as extensions of variable-width internal channels, it becomes possible to exploit geometrical features, such as channel width, to shift the band gap position and size to desired frequencies. Time transient simulations demonstrate the effectiveness of the proposed metastructures for wave manipulation in terms of transmission or reflection coefficients, amplitude attenuation and time delay at subwavelength frequencies. The obtained results can be important for practical applications of LAMMs such as lightweight acoustic barriers with enhanced broadband wave-reflecting performances.

Magnetic domain walls as reconfigurable spin-wave nano-channels

NASA Astrophysics Data System (ADS)

Wagner, Kai

Research efforts to utilize spin waves as information carriers for wave based logic in micro- and nano-structured ferromagnetic materials have increased tremendously over the recent years. However, finding efficient means of tailoring and downscaling guided spin-wave propagation in two dimensions, while maintaining energy efficiency and reconfigurability, still remains a delicate challenge. Here we target these challenges by spin-wave transport inside nanometer-scaled potential wells formed along magnetic domain walls. For this, we investigate the magnetization dynamics of a rectangular-like element in a Landau state exhibiting a so called 180° Néel wall along its center. By microwave antennae the rf-excitation is constricted to one end of the domain wall and the spin-wave intensities are recorded by means of Brillouin-Light Scattering microscopy revealing channeled transport. Additional micromagnetic simulations with pulsed as well as cw-excitation are performed to yield further insight into this class of modes. We find several spin-wave modes quantized along the width of the domain wall yet with well defined wave vectors along the wall, exhibiting positive dispersion. In a final step, we demonstrate the flexibility of these spin-wave nano-channels based on domain walls. In contrast to wave guides realised by fixed geometries, domain walls can be easily manipulated. Here we utilize small external fields to control its position with nanometer precision over a micrometer range, while still enabling transport. Domain walls thus, open the perspective for reprogrammable and yet non-volatile spin-wave waveguides of nanometer width. Financial support by the Deutsche Forschungsgemeinschaft within project SCHU2922/1-1 is gratefully acknowledged.

Changes to channel sediments resulting from complex human impacts in a gravel-bed river, Polish Carpathians

NASA Astrophysics Data System (ADS)

Zawiejska, Joanna; Wyżga, Bartłomiej; Hajdukiewicz, Hanna; Radecki-Pawlik, Artur; Mikuś, Paweł

2016-04-01

During the second half of the twentieth century, many sections of the Czarny Dunajec River, Polish Carpathians, were considerably modified by channelization as well as gravel-mining and the resultant channel incision (up to 3.5 m). This paper examines changes to the longitudinal pattern of grain size and sorting of bed material in an 18-km-long river reach. Surface bed-material grain size was established on 47 gravel bars and compared with a reference downstream fining trend of bar sediments derived from the sites with average river width and a vertically stable channel. Contrary to expectations, the extraction of cobbles from the channel bed in the upper part of the study reach, conducted in the past decades, has resulted in the marked coarsening of bed material in this river section. The extraction facilitated entrainment of exposed finer grains and has led to rapid bed degradation, whereas the concentration of flood flows in the increasingly deep and narrow channel has increased their competence and enabled a delivery of the coarse particles previously typical of the upstream reach. The middle section of the study reach, channelized to prevent sediment delivery to a downstream reservoir, now transfers the bed material flushed out from the incising upstream section. With considerably increased transport capacity of the river and with sediment delivery from bank erosion eliminated by bank reinforcements, bar sediments in the channelized section are typified by increased size of the finer fraction and better-than-average sorting. In the wide, multi-thread channel in the lower part of the reach, low unit stream power and high channel-form roughness facilitate sediment deposition and are reflected in relatively fine grades of bar gravels. The study showed that selective extraction of larger particles from the channel bed leads to channel incision at and upstream of the mining site. However, unlike bulk gravel mining, selective extraction does not result in sediment deficit downstream as large volumes of finer bed material are flushed out from the incising channel section. Grain-size analyses of bulk gravels and measurements of 100 coarsest particles within the channel sediment ranging in age from 5200 years BP to the present, performed in this deeply incised section, indicated that grain size of channel sediments changed relatively little since mid-Holocene to the 1960s, but has increased rapidly over the last half-century as a result of human interventions and rapidly progressing channel incision. This study was performed within the scope of the Research Project DEC-2013/09/B/ST10/00056 financed by the National Science Centre of Poland.

The Effect of Electrokinetic Controlled Wettability on Externally Measured Pressures for a Micro-Fluidic Channel

NASA Astrophysics Data System (ADS)

Zhou, X.; Nolte, D. D.; Pyrak-Nolte, L. J.

2017-12-01

The hysteretic relationship between capillary pressure (Pc) on saturation (S) has been shown to be a projection of a higher-dimensional surface that depends on interfacial area per volume (IAV) as the additional state variable. Most studies that validate the capillary-pressure-saturation-IAV relationship are performed on 2D micro-models or cores where scanning is performed in pressure and not in saturation. We have developed an EWOD technique (electro-wetting on dielectric) to internally manipulate fluid saturation to determine the effect on externally measured pressures. Applying electric fields to electrolytic fluids changes the contact angle among the fluids and the solid. For a parallel-plate electro-wetting set-up, the pressure difference is given by gsl (cosq'EW - cosqEW )/d', where d' is the aperture, qEQ and q'EW are the contact angles before and after the application of voltage, V, and gsl is the interfacial tension between the solid and liquid phases. This pressure difference enables direct control over internal fluid distributions. The contact angle reverts to the original value when V = 0. A sealed micro-model with Electro-Wetting on Dielectric (EWOD) electrodes was fabricated using a PDMS wedge-shaped channel with an entrance width of 1 mm and an exit width of 2 mm. The channel length was 2 mm, and had a depth of 0.9 mm. The PDMS channel was attached to an aluminum plate that served as the ground electrode. An ITO slide coated with PDMS formed the high voltage electrode and was used to seal the micro-model. X-ray Micro-CT scans showed that the contact angle between electrodes changes from from 110˚ (non-wetting) to 70˚ (wetting) for an applied voltage of 318 V AC. By applying voltage to the wedge-shaped micromodel, with the inlet and the outlet opened to the atmosphere, the externally measured capillary pressure remained constant even though the fluid-air interface moved and the saturation increased. For a closed system, the externally measured change in capillary pressure was 30 Pa and the saturation in the channel increased. EWOD provides method to assess the contributions of wettability to the fundamental physics of immiscible fluids in analog porous media. Acknowledgment: This research was supported by the National Science Foundation (1314663-EAR).

Do distributaries in a delta plain resemble an ideal estuary? Results from theKapuas Delta,Indonesia

NASA Astrophysics Data System (ADS)

Hoitink, T.; Kastner, K.; Vermeulen, B.; Geertsema, T.; Nining, S. N.

2017-12-01

Coastal lowland plains under mixed fluvial-tidal influence can form complex channel networks, where distributaries blend the characteristics of mouth bar channels, avulsion channels and tidal creeks. These networks are shaped by the interplay of river flow and tides. Our goal is to increase the general understanding of physical processes in the fluvial-tidal transition. Here we present first results of an extensive field survey of the Kapuas river and give insight into the along channel trends of cross section geometry and bed material grain size. main distributary and slightly increases in downstream direction (Fig. 2c).The Kapuas river is a large tropical river in West Kalimantan, Indonesia. Discharge ranges between 10^3 m^3/s in the wet and 10^4 m^3/s in the dry season. The Kapuas consists of one main distributary from which three smaller distributaries branch off along the alluvial plain (Fig. 1a). Tides are mainly diurnal, with an average spring range of 1.5m at the mouth.Figure 1: Map of the Kapuas river delta plain Between 2013 and 2015 we surveyed the Kapuas from the sea to upstream km 300. Bankfull river width was extracted from Landsat images. Bathymetry was surveyed with a single beam each sounder. Bed material was sampled with a van Veen grabber. The geometry of the Kapuas river deviates from that of an idealized estuary, as it does not converge to an equilibirum width and depth. Such a break in scaling was previously found in the Mahakam Delta by Sassi et al. 2012, which suggests this may be a general characteristic in the fluvial to tidal transition. There is no simple relation between bed material grain size and channel geometry. The particular geometry of the Kapuas also leads to particular hydrodynamics in the fluvial-tidal transition. Thus the draw-down curve during high flow and backwater curve at flow are much less pronounced in the Kapuas, and tides propagate far up the river. At the moment we investigate the consequences for river discharge-tide interaction. In particular we focus on propagation of the tide depending on the river discharge as well as consequences for delta morphology.

Resistance modulation in VO2 nanowires induced by an electric field via air-gap gates

NASA Astrophysics Data System (ADS)

Kanki, Teruo; Chikanari, Masashi; Wei, Tingting; Tanaka, Hidekazu; The Institute of Scientific; Industrial Research Team

Vanadium dioxide (VO2) shows huge resistance change with metal-insulator transition (MIT) at around room temperature. Controlling of the MIT by applying an electric field is a topical ongoing research toward the realization of Mott transistor. In this study, we have successfully switched channel resistance of VO2 nano-wire channels by a pure electrostatic field effect using a side-gate-type field-effect transistor (SG-FET) viaair gap and found that single crystalline VO2 nanowires and the channels with narrower width enhance transport modulation rate. The rate of change in resistance ((R0-R)/R, where R0 and R is the resistance of VO2 channel with off state and on state gate voltage (VG) , respectively) was 0.42 % at VG = 30 V in in-plane poly-crystalline VO2 channels on Al2O3(0001) substrates, while the rate in single crystalline channels on TiO2 (001) substrates was 3.84 %, which was 9 times higher than that using the poly-crystalline channels. With reducing wire width from 3000 nm to 400 nm of VO2 on TiO2 (001) substrate, furthermore, resistance modulation ratio enhanced from 0.67 % to 3.84 %. This change can not be explained by a simple free-electron model. In this presentation, we will compare the electronic properties between in-plane polycrystalline VO2 on Al2O3 (0001) and single crystalline VO2 on TiO2 (001) substrates, and show experimental data in detail..

Runoff production from intercrater plains on Mars

NASA Astrophysics Data System (ADS)

Irwin, R. P., III; Matsubara, Y.; Cawley, J. C.

2016-12-01

Ancient fluvial paleochannels and paleolakes constrain the hydrology of a wetter epoch in the early history of Mars. The cross-sectional dimensions of fluvial channels scale with discharge, watershed topography is generally well preserved, and adjustments can be made for gravity. These factors have supported conservative estimates of runoff production during event floods more than 3.5 billion years ago. Assuming weak channel banks, such that discharge is low per unit channel width, event floods in smaller watersheds had estimated runoff production of 1 cm/day. Highland surfaces generated runoff inefficiently, such that channel width increases with only the 0.3 power of watershed area. Inefficient runoff production on Mars is also suggested by new landscape evolution modeling. In long-term simulations that accurately reproduce the present landscape, forming and degrading all of the Middle and Late Noachian impact craters in selected study areas, inefficient runoff production is needed to degrade craters without intensely dissecting intercrater surfaces. The model shows that discharge generally cannot increase at more than the 0.3 power of watershed area. Paleolakes provide useful constraints on paleohydrology over intermediate timescales of years to millennia. Most local highland basins were never integrated into regional drainage systems, but some have both a contributing valley network and an outlet valley, indicating that they overflowed. Paleolake overflows require a medium-term water supply that exceeds losses to evaporation. Reasonable evaporation of 0.1 to 1 m/yr and watersheds that are mostly >10 times the area of overflowed paleolakes suggest runoff production of <0.1 m per year. Event floods were both moderate and rare during peak fluvial conditions on Mars. Over the bulk of the Middle and Late Noachian Epochs, the loss of small craters, scarp retreat, and basin infilling suggest less intense fluvial activity along with weathering, impact gardening, and lesser aeolian erosion. Low drainage density is an obvious explanation for inefficient runoff production, but it may be the consequence of moderate rainfall or snowmelt, as well as incision of valley networks over a finite timescale.

Liquid Jet Cavitation via Molecular Dynamics

NASA Astrophysics Data System (ADS)

Ashurst, W. T.

1997-11-01

A two-dimensional molecular dynamics simulation of a liquid jet is used to investigate cavitation in a diesel-like fuel injector. A channel with a length four times its width has been examined at various system sizes (widths of 20 to 160 σ, where σ is the zero energy location in the Lennard-Jones potential). The wall boundary condition is Maxwell's diffuse reflection, similar to the work by Sun & Ebner (Phys. Rev A 46, 4813, 1992). Currently, the jet exhausts into a vacuum, but a second, low density gas will be incorporated to represent the compressed air in a diesel chamber. Four different flow rates are examined. With ρ U equal to √mɛ/σ^2 (the largest flow rate) the static pressure decreases by a factor of twenty between the channel entrance and exit. The largest flow rate has a parabolic velocity profile with almost constant density across the channel. The smallest flow rate has the same velocity profile but the density exhibits a large variation, with the minimum value in the channel center. Thus, the product ρ U is nearly constant across the channel at this flow rate. The discharge coefficient CD has a small variation with flow rate, but the velocity coefficient CV varies with the amount of two-phase fluid within the channel. The ratio of CV to CD varies from 1.3 (largest flow rate) to 2.0 (the smallest flow rate, which is one-eighth of the largest).

Topographic Signatures of Meandering Rivers with Differences in Outer Bank Cohesion

NASA Astrophysics Data System (ADS)

Kelly, S. A.; Belmont, P.

2014-12-01

Within a given valley setting, interactions between river hydraulics, sediment, topography, and vegetation determine attributes of channel morphology, including planform, width and depth, slope, and bed and bank properties. These feedbacks also govern river behavior, including migration and avulsion. Bank cohesion, from the addition of fine sediment and/or vegetation has been recognized in flume experiments as a necessary component to create and maintain a meandering channel planform. Greater bank cohesion slows bank erosion, limiting the rate at which a river can adjust laterally and preventing so-called "runaway widening" to a braided state. Feedbacks of bank cohesion on channel hydraulics and sediment transport may thus produce distinct topographic signatures, or patterns in channel width, depth, and point bar transverse slope. We expect that in bends of greater outer bank cohesion the channel will be narrower, deeper, and bars will have greater transverse slopes. Only recently have we recognized that biotic processes may imprint distinct topographic signatures on the landscape. This study explores topographic signatures of three US rivers: the lower Minnesota River, near Mankato, MN, the Le Sueur River, south central MN, and the Fall River, Rocky Mountain National Park, CO. Each of these rivers has variability in outer bank cohesion, quantified based on geotechnical and vegetation properties, and in-channel topography, which was derived from rtkGPS and acoustic bathymetry surveys. We present methods for incorporating biophysical feedbacks into geomorphic transport laws so that models can better simulate the spatial patterns and variability of topographic signatures.

Characterizing the transient geomorphic response to base-level fall in the northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Zhang, Huiping; Kirby, Eric; Pitlick, John; Anderson, Robert S.; Zhang, Peizhen

2017-02-01

Analysis of hillslope gradient, landscape relief, and channel steepness in the Daxia River basin provides evidence of a transient geomorphic response to base-level fall on the northeastern Tibetan Plateau. Low-gradient channels and gentle hillslopes of the upper watershed are separated from a steeper, high-relief landscape by a series of convex knickzones along channel longitudinal profiles. Downstream projection of the "relict" portions of the profiles implies 800-850 m of incision, consistent with geologic and geomorphic records of post 1.7 Ma incision in the lower watershed. We combine optically stimulated luminescence dating of fluvial terrace deposits to constrain incision rates downstream of knickpoints with catchment-averaged 10Be concentrations in modern sediment to estimate erosion rates in tributary basins both above and below knickpoints. Both sources of data imply landscape lowering rates of 300 m Ma-1 below the knickpoint and 50-100 m Ma-1 above. Field measurements of channel width (n = 48) and calculations of bankfull discharge (n = 9) allow determination of scaling relations among channel hydraulic geometry, discharge, and contributing area that we employ to estimate the patterns of basal shear stress, unit stream power, and bed load transport rate throughout the channel network. Our results imply a clear downstream increase of incision potential; this result would appear to be consistent with a detachment-limited response to imposed base-level fall, in which steepening of channels drives an increase in erosion rates. In contrast, however, we do not observe apparent narrowing of channels across the transition from slowly eroding to rapidly eroding portions of the watershed. Rather, the present-day channel morphology as well as its scaling of hydraulic geometry imply that the river is primarily adjusted to transport its sediment load and suggest that channel morphology may not always reflect the presence of knickpoints and differences in landscape relief.

Separate channels for the analysis of the shape and the movement of moving visual stimulus.

PubMed

Tolhurst, D J

1973-06-01

1. The effects of temporal modulation on the properties of spatial frequency channels have been investigated using adaptation.2. Adapting to drifting sinusoidal gratings caused threshold elevation that was both spatial frequency and direction specific. Little systematic difference was found between the band widths of the elevation curves for drifting and stationary gratings.3. It was confirmed that adaptation fails to reveal channels at low spatial frequencies when stationary gratings are used. However, channels were revealed at frequencies at least as low as 0.66 c/deg when the test gratings were made to move. These channels are adapted only a little by stationary gratings, confirming their dependence on movement.4. The existence of movement-sensitive channels at low spatial frequencies explains the well known observation that temporal modulation greatly increases the sensitivity of the visual system to low spatial frequencies.5. Temporal modulation was effective at revealing these channels only when the flicker or movement of the test patterns was apparent to the observer; only at low spatial frequencies did patterns, modulated at low rates, actually appear to be temporarily modulated at threshold. At higher spatial frequencies, they were indistinguishable from stationary patterns until the contrast was some way above the detection threshold.6. It is suggested, therefore, that the movement-sensitive channels are responsible for signalling the occurrence of movement; the channels at higher spatial frequencies give no information about temporal changes. These two systems of channels are compared to the Y- and X-cells respectively of the cat.

One-dimensional spatial dark soliton-induced channel waveguides in lithium niobate crystal.

PubMed

Zhang, Peng; Ma, Yanghua; Zhao, Jianlin; Yang, Dexing; Xu, Honglai

2006-04-01

The anisotropic dependence of the formation of one-dimensional (1-D) spatial dark solitons on the orientation of intensity gradients in lithium niobate crystal is numerically specified. Based on this, we propose an approach to fabricate channel waveguides by employing 1-D spatial dark solitons. By exposure of two 1-D dark solitons with different orientations, channel waveguides can be created. The structures of the channel waveguides can be tuned by adjustment of the widths of the solitons and/or the angles between the two exposures. A square channel waveguide is experimentally demonstrated in an iron-doped lithium niobate crystal by exposure of two orthogonal 1-D dark solitons in sequence.

The key role of dislocation dissociation in the plastic behaviour of single crystal nickel-based superalloy with low stacking fault energy: Three-dimensional discrete dislocation dynamics modelling

NASA Astrophysics Data System (ADS)

Huang, Minsheng; Li, Zhenhuan

2013-12-01

To model the deformation of single crystal nickel based superalloys (SCNBS) with low stacking fault energy (SFE), three-dimensional discrete dislocation dynamics (3D-DDD) is extended by incorporating dislocation dissociation mechanism. The present 3D-DDD simulations show that, consistent with the existing TEM observation, the leading partial can enter the matrix channel efficiently while the trailing partial can hardly glide into it when the dislocation dissociation is taken into account. To determine whether the dislocation dissociation can occur or not, a critical percolation stress (CPS) based criterion is suggested. According to this CPS criterion, for SCNBS there exists a critical matrix channel width. When the channel width is lower than this critical value, the dislocation tends to dissociate into an extended configuration and vice versa. To clarify the influence of dislocation dissociation on CPS, the classical Orowan formula is improved by incorporating the SFE. Moreover, the present 3D-DDD simulations also show that the yielding stress of SCNBSs with low SFE may be overestimated up to 30% if the dislocation dissociation is ignored. With dislocation dissociation being considered, the size effect due to the width of γ matrix channel and the length of γ‧ precipitates on the stress-strain responses of SCNBS can be enhanced remarkably. In addition, due to the strong constraint effect by the two-phase microstructure in SCNBS, the configuration of formed junctions is quite different from that in single phase crystals such as Cu. The present results not only provide clear understanding of the two-phase microstructure levelled microplastic mechanisms in SCNBSs with low SFE, but also help to develop new continuum-levelled constitutive laws for SCNBSs.

River self-organisation inhibits discharge control on waterfall migration.

PubMed

Baynes, Edwin R C; Lague, Dimitri; Attal, Mikaël; Gangloff, Aurélien; Kirstein, Linda A; Dugmore, Andrew J

2018-02-05

The action of rivers within valleys is fundamentally important in controlling landscape morphology, and how it responds to tectonic or climate change. The response of landscapes to external forcing usually results in sequential changes to river long profiles and the upstream migration of waterfalls. Currently, models of this response assume a relationship between waterfall retreat rate and drainage area at the location of the waterfall. Using an experimental study, we show that this assumption has limited application. Due to a self-regulatory response of channel geometry to higher discharge through increasing channel width, the bed shear stress at the lip of the experimental waterfall remains almost constant, so there was no observed change in the upstream retreat rate despite an order of magnitude increase in discharge. Crucially, however, the strength of the bedrock material exhibits a clear control on the magnitude of the mean retreat rate, highlighting the importance of lithology in setting the rate at which landscapes respond to external forcing. As a result existing numerical models of landscape evolution that simulate the retreat of waterfalls as a function of drainage area with a fixed erodibility constant should be re-evaluated to consider spatial heterogeneity in erodibility and channel self-organisation.

Characterizing the SWOT discharge error budget on the Sacramento River, CA

NASA Astrophysics Data System (ADS)

Yoon, Y.; Durand, M. T.; Minear, J. T.; Smith, L.; Merry, C. J.

2013-12-01

The Surface Water and Ocean Topography (SWOT) is an upcoming satellite mission (2020 year) that will provide surface-water elevation and surface-water extent globally. One goal of SWOT is the estimation of river discharge directly from SWOT measurements. SWOT discharge uncertainty is due to two sources. First, SWOT cannot measure channel bathymetry and determine roughness coefficient data necessary for discharge calculations directly; these parameters must be estimated from the measurements or from a priori information. Second, SWOT measurement errors directly impact the discharge estimate accuracy. This study focuses on characterizing parameter and measurement uncertainties for SWOT river discharge estimation. A Bayesian Markov Chain Monte Carlo scheme is used to calculate parameter estimates, given the measurements of river height, slope and width, and mass and momentum constraints. The algorithm is evaluated using simulated both SWOT and AirSWOT (the airborne version of SWOT) observations over seven reaches (about 40 km) of the Sacramento River. The SWOT and AirSWOT observations are simulated by corrupting the ';true' HEC-RAS hydraulic modeling results with the instrument error. This experiment answers how unknown bathymetry and roughness coefficients affect the accuracy of the river discharge algorithm. From the experiment, the discharge error budget is almost completely dominated by unknown bathymetry and roughness; 81% of the variance error is explained by uncertainties in bathymetry and roughness. Second, we show how the errors in water surface, slope, and width observations influence the accuracy of discharge estimates. Indeed, there is a significant sensitivity to water surface, slope, and width errors due to the sensitivity of bathymetry and roughness to measurement errors. Increasing water-surface error above 10 cm leads to a corresponding sharper increase of errors in bathymetry and roughness. Increasing slope error above 1.5 cm/km leads to a significant degradation due to direct error in the discharge estimates. As the width error increases past 20%, the discharge error budget is dominated by the width error. Above two experiments are performed based on AirSWOT scenarios. In addition, we explore the sensitivity of the algorithm to the SWOT scenarios.

Geometric effects on mixing performance in a novel passive micromixer with trapezoidal-zigzag channels

NASA Astrophysics Data System (ADS)

Le The, Hai; Ta, Bao Quoc; Le Thanh, Hoa; Dong, Tao; Nguyen Thoi, Trung; Karlsen, Frank

2015-09-01

A novel passive micromixer, called a trapezoidal-zigzag micromixer (TZM), is reported. A TZM is composed of trapezoidal channels in a zigzag and split-recombine arrangement that enables multiple mixing mechanisms, including splitting-recombining, twisting, transversal flows, vortices, and chaotic advection. The effects of geometric parameters of the TZM on mixing performance are systematically investigated by the Taguchi method and numerical simulations in COMSOL Multiphysics. The number of mixing units, the slope angle of the trapezoidal channel, the height of the constriction element, and the width ratio between the middle-trapezoidal channel and the side-trapezoidal channel are the four parameters under study. The mixing performance of the TZM is investigated at three different Reynolds number (Re) values of 0.5, 5, and 50. The results showed that a TZM with six mixing units, a trapezoidal slope angle of 75°, a constricting height of 100 µm, and a width ratio of 0.5 has the highest mixing efficiency. This optimal TZM has a mixing efficiency greater than 85% for Re values from 0.1 to 80. In particular, for Re  ⩽  0.9 and Re  ⩾  20, the mixing efficiency of the optimal TZM is greater than 90%. The proposed TZM has a higher mixing efficiency and a smaller footprint than previously reported micromixers.

Higgs constraints from vector boson fusion and scattering

DOE PAGES

Campbell, John M.; Ellis, R. Keith

2015-04-07

We present results on 4-lepton + 2-jet production, the partonic processes most commonly described as vector boson pair production in the Vector Boson Fusion (VBF) mode. That final state contains diagrams that are mediated by Higgs boson exchange. We focus particularly on the high-mass behaviour of the Higgs boson mediated diagrams, which unlike on-shell production, gives information about the Higgs couplings without assumptions on the Higgs boson total width. We assess the sensitivity of the high-mass region to Higgs coupling strengths, considering all vector boson pair channels, W - W +, W ± W ±, W ± Z and ZZ.more » Because of the small background, the most promising mode is W + W + which has sensitivity to Higgs couplings because of Higgs boson exchange in the t-channel. Furthermore, using the Caola-Melnikov (CM) method, the off-shell couplings can be interpreted as bounds on the Higgs boson total width. We estimate the bound that can be obtained with current data, as well as the bounds that could be obtained at √s=13 TeV in the VBF channel for data samples of 100 and 300 fb -1. The CM method has already been successfully applied in the gluon fusion (GGF) production channel. The VBF production channel gives important complementary information, because both production and decay of the Higgs boson occur already at tree graph level.« less

Are Streams in the Southwestern Ozarks Underfit? Applying Dury's model to the Illinois River Watershed in Arkansas.

NASA Astrophysics Data System (ADS)

Shepherd, S. L.; Davis, R. K.; Dixon, J. C.; Cothren, J. D.

2008-12-01

George H. Dury (1964) proposed eight theoretical combinations of stream pattern and valley pattern that represent underfit streams; claiming underfit is a climate induced condition caused by a significant decrease in channel forming discharge. One combination was defined by the Osage River in the northeastern Ozark Plateaus of Missouri. Osage underfit streams fail to meander within a meandering valley. The mean channel meander wavelength and channel width of the stream is much less than the valley resulting in valley-stream ratios of up to 40:1 in contrast to his expected values of approximately 11:1. Dury's model is generally applied to the entire Ozarks including the Illinois River watershed without field data support. The Illinois River is located on the western flank of the Ozark Plateaus physiographic region on the Springfield Plateau which has different lithology than the Salem Plateau where the Osage River is located. To test the assumption that streams in the Illinois River watershed are underfit a combination of field, map, and GIS data were collected. Geomorphic surveys of ten reaches along eight first order streams were completed. The average stream widths of the ten reaches were compared to valley widths measured from USGS 1:24000 Quadrangle maps. The valley to stream ratios ranged from 1 to 15. Forested watersheds exhibited the highest width ratios, ranging from 12 to 15, while ratios in urban and agricultural watersheds were less than 2. This finding is consistent with observed changes in stream morphology caused by anthropogenic influences. To extrapolate to the larger watershed thirteen valley and stream widths along the Illinois River and two higher order tributaries, Osage Creek and Clear Creek, were measured from USGS maps. These ratios ranged from 2.8 to 5.7. Additionally, stream and valley wavelengths are being analyzed in a GIS using the USGS medium resolution hydrology data set and a LiDAR derived 8 m DEM for the watershed. These data suggest it is invalid to apply the Osage underfit model to this watershed. These findings are being validated with additional stream and valley width measurements in the field along the first order streams, Osage Creek, Clear Creek, and the Illinois River.

Assessment of an in-channel redistribution technique for large woody debris management in Locust Creek, Linn County, Missouri

USGS Publications Warehouse

Heimann, David C.

2017-10-24

The U.S. Geological Survey, in cooperation with the Missouri Department of Conservation and Missouri Department of Natural Resources, completed a study to assess a mechanical redistribution technique used for the management of large woody debris (LWD) jams in Locust Creek within Pershing State Park and Fountain Grove Conservation Area, Linn County, Missouri. Extensive LWD jams were treated from 1996 to 2009 using a low-impact technique in which LWD from the jams was redistributed to reopen the channel and to mimic the natural geomorphic process of channel migration and adjustment to an obstruction. The scope of the study included the comparison of selected channel geometry characteristics and bed material particle-size distribution in seven LWD treatment reaches with that of adjacent untreated reaches (unaffected by LWD accumulations) of Locust Creek. A comparison of 1996 and 2015 survey cross sections in treated and untreated reaches and photograph documentation were used to assess channel geomorphic change and the stability of redistributed LWD. The physical characteristics of LWD within jams present in the study reach during 2015–16 also were documented.Based on the general lack of differences in channel metrics between treated and untreated reaches, it can be concluded that the mechanical redistribution technique has been an effective treatment of extensive LWD jams in Locust Creek. Channel alterations, including aggradation, streamflow piracy, and diversions, have resulted in temporal and spatial changes in the Locust Creek channel that may affect future applications of the redistribution technique in Pershing State Park. The redistribution technique was used to effectively manage LWD in Locust Creek at a potentially lower financial cost and reduced environmental disturbance than the complete removal of LWD.A comparison of four channel metrics (bankfull cross-sectional area, channel width, streamflow capacity, and width-depth ratio) for individual treatment reaches with adjacent untreated reaches indicated no statistically significant difference in most comparisons. Where statistically significant differences in channel metrics were determined between individual reaches, the channel metrics in treatment reaches were significantly less than adjacent untreated reaches in some comparisons, and significantly greater than adjacent untreated reaches in others. Without immediate posttreatment cross sections in treated and untreated reaches for comparison, it is impossible to say with certainty that a lack of significant differences in channel metrics is a result of posttreatment channel adjustment or, conversely, that any significant differences that remain are a result of the treatment of LWD.Characteristics of LWD in accumulations sampled within the study area in 2015 indicate that most sampled pieces were in the 1–2 foot diameter size class, the 5–16 foot length class, and the advanced decay class. Most of documented LWD pieces were loose and not buried, about 20 percent on average had a root wad attached, and about 6.5 percent on average were sawn logs. Most of sampled material was less than one-half of the bankfull channel width, indicating it was easily transportable, and the advanced decay class of material entering the study area indicated that it was likely sourced from outside of Pershing State Park.Redistributed LWD associated with treatment seems to be intact in the 1996 treated reaches from direct observation and from inference because there was net channel aggradation between 1996 and 2015 in comparison surveys. The change in channel area resulting from aggradation in time (1996 to 2015) in treated and untreated reaches exceeded the differences in channel characteristics between the treated and untreated channels in 2015 surveys.

Relative importance of impervious area, drainage density, width function, and subsurface storm drainage on flood runoff from an urbanized catchment

NASA Astrophysics Data System (ADS)

Ogden, Fred L.; Raj Pradhan, Nawa; Downer, Charles W.; Zahner, Jon A.

2011-12-01

The literature contains contradictory conclusions regarding the relative effects of urbanization on peak flood flows due to increases in impervious area, drainage density and width function, and the addition of subsurface storm drains. We used data from an urbanized catchment, the 14.3 km2 Dead Run watershed near Baltimore, Maryland, USA, and the physics-based gridded surface/subsurface hydrologic analysis (GSSHA) model to examine the relative effect of each of these factors on flood peaks, runoff volumes, and runoff production efficiencies. GSSHA was used because the model explicitly includes the spatial variability of land-surface and hydrodynamic parameters, including subsurface storm drains. Results indicate that increases in drainage density, particularly increases in density from low values, produce significant increases in the flood peaks. For a fixed land-use and rainfall input, the flood magnitude approaches an upper limit regardless of the increase in the channel drainage density. Changes in imperviousness can have a significant effect on flood peaks for both moderately extreme and extreme storms. For an extreme rainfall event with a recurrence interval in excess of 100 years, imperviousness is relatively unimportant in terms of runoff efficiency and volume, but can affect the peak flow depending on rainfall rate. Changes to the width function affect flood peaks much more than runoff efficiency, primarily in the case of lower density drainage networks with less impermeable area. Storm drains increase flood peaks, but are overwhelmed during extreme rainfall events when they have a negligible effect. Runoff in urbanized watersheds with considerable impervious area shows a marked sensitivity to rainfall rate. This sensitivity explains some of the contradictory findings in the literature.

Modeling the evolution of channel shape: Balancing computational efficiency with hydraulic fidelity

USGS Publications Warehouse

Wobus, C.W.; Kean, J.W.; Tucker, G.E.; Anderson, R. Scott

2008-01-01

The cross-sectional shape of a natural river channel controls the capacity of the system to carry water off a landscape, to convey sediment derived from hillslopes, and to erode its bed and banks. Numerical models that describe the response of a landscape to changes in climate or tectonics therefore require formulations that can accommodate evolution of channel cross-sectional geometry. However, fully two-dimensional (2-D) flow models are too computationally expensive to implement in large-scale landscape evolution models, while available simple empirical relationships between width and discharge do not adequately capture the dynamics of channel adjustment. We have developed a simplified 2-D numerical model of channel evolution in a cohesive, detachment-limited substrate subject to steady, unidirectional flow. Erosion is assumed to be proportional to boundary shear stress, which is calculated using an approximation of the flow field in which log-velocity profiles are assumed to apply along vectors that are perpendicular to the local channel bed. Model predictions of the velocity structure, peak boundary shear stress, and equilibrium channel shape compare well with predictions of a more sophisticated but more computationally demanding ray-isovel model. For example, the mean velocities computed by the two models are consistent to within ???3%, and the predicted peak shear stress is consistent to within ???7%. Furthermore, the shear stress distributions predicted by our model compare favorably with available laboratory measurements for prescribed channel shapes. A modification to our simplified code in which the flow includes a high-velocity core allows the model to be extended to estimate shear stress distributions in channels with large width-to-depth ratios. Our model is efficient enough to incorporate into large-scale landscape evolution codes and can be used to examine how channels adjust both cross-sectional shape and slope in response to tectonic and climatic forcing. Copyright 2008 by the American Geophysical Union.

Complex channel responses to changes in stream flow and sediment supply on the lower Duchesne River, Utah

USGS Publications Warehouse

Gaeuman, D.; Schmidt, J.C.; Wilcock, P.R.

2005-01-01

Channel responses to flow depletions in the lower Duchesne River over the past 100 years have been highly complex and variable in space and time. In general, sand-bed reaches adjusted to all perturbations with bed-level changes, whereas the gravel-bed reaches adjusted primarily through width changes. Gravel-bed reaches aggraded only when gravel was supplied to the channel through local bank erosion and degraded only during extreme flood events. A 50% reduction in stream flow and an increase in fine sediment supply to the study area occurred in the first third of the 20th century. The gravel-bed reach responded primarily with channel narrowing, whereas bed aggradation and four large-scale avulsions occurred in the sand-bed reaches. These avulsions almost completely replaced a section of sinuous channel about 14 km long with a straighter section about 7 km long. The most upstream avulsion, located near a break in valley slope and the transition from a gravel bed upstream and a sand bed downstream, transformed a sinuous sand-bed reach into a braided gravel-bed reach and eventually into a meandering gravel-bed reach over a 30-year period. Later, an increase in flood magnitudes and durations caused widening and secondary bed aggradation in the gravel-bed reaches, whereas the sand-bed reaches incised and narrowed. Water diversions since the 1950s have progressively eliminated moderate flood events, whereas larger floods have been less affected. The loss of frequent flooding has increased the duration and severity of drought periods during which riparian vegetation can establish along the channel margins. As a result, the channel has gradually narrowed throughout the study area since the late 1960s, despite the occasional occurrence of large floods. No tributaries enter the Duchesne River within the study area, so all reaches have experienced identical changes in stream flow and upstream sediment supply. ?? 2004 Elsevier B.V. All rights reserved.

Hydraulic geometry and streamflow of channels in the Piceance Basin, Rio Blanco and Garfield counties, Colorado

USGS Publications Warehouse

Elliott, J.G.; Cartier, K.D.

1986-01-01

The influence of streamflow and basin characteristics on channel geometry was investigated at 18 perennial and ephemeral stream reaches in the Piceance basin of northwestern Colorado. Results of stepwise multiple regression analyses indicated that the variabilities of mean bankfull depth (D) and bankfull cross-sectional flow area (Af) were predominantly a function of bankfull discharge (QB), and that most of the variability in channel slopes (S) could be explained by drainage area (DA). None of the independent variables selected for the study could account for a large part of the variability in bankfull channel width (W). (USGS)

Rare Earth Optical Temperature Sensor

NASA Technical Reports Server (NTRS)

Chubb, Donald L. (Inventor); Jenkins, Phillip (Inventor)

2004-01-01

A rare earth optical temperature sensor is disclosed for measuring high temperatures. Optical temperature sensors exist that channel emissions from a sensor to a detector using a light pipe. The invention uses a rare earth emitter to transform the sensed thermal energy into a narrow band width optical signal that travels to a detector using a light pipe. An optical bandpass filter at the detector removes any noise signal outside of the band width of the signal from the emitter.

National Dam Safety Program. Roxbury Dam (Inventory Number 788) Delaware River Basin, Delaware County, New York. Phase I Inspection Report,

DTIC Science & Technology

1980-05-21

service spillway was analyzed as a sharp - crested weir with:.a discharge coefficient (c) of 3.1. The auxiliary spillway channel was analyzed as a broad ...upstream portion of this channel is a concrete structure which forms a 27.4 foot long rectangular weir . There is a 5 foot vertical drop beyond the crest ...I on 1.5 Crest Width (ft) 12 g. Service Spillway Type: Concrete channel-rectangular weir . Five foot vertical drop beyond crest . Masonry and laid up

Bankfull-channel geometry and discharge curves for the Rocky Mountains Hydrologic Region in Wyoming

USGS Publications Warehouse

Foster, Katharine

2012-01-01

Regional curves relate bankfull-channel geometry and bankfull discharge to drainage area in regions with similar runoff characteristics and are used to estimate the bankfull discharge and bankfull-channel geometry when the drainage area of a stream is known. One-variable, ordinary least-squares regressions relating bankfull discharge, cross-sectional area, bankfull width, and bankfull mean depth to drainage area were developed from data collected at 35 streamgages in or near Wyoming. Watersheds draining to these streamgages are within the Rocky Mountains Hydrologic Region of Wyoming and neighboring states.

Fully transparent thin film transistors based on zinc oxide channel layer and molybdenum doped indium oxide electrodes

NASA Astrophysics Data System (ADS)

MÄ dzik, Mateusz; Elamurugu, Elangovan; Viegas, Jaime

2016-03-01

In this work we report the fabrication of thin film transistors (TFT) with zinc oxide channel and molybdenum doped indium oxide (IMO) electrodes, achieved by room temperature sputtering. A set of devices was fabricated, with varying channel width and length from 5μm to 300μm. Output and transfer characteristics were then extracted to study the performance of thin film transistors, namely threshold voltage and saturation current, enabling to determine optimal fabrication process parameters. Optical transmission in the UV-VIS-IR are also reported.

Two-phase flow in short horizontal rectangular microchannels with a height of 300 μm

NASA Astrophysics Data System (ADS)

Chinnov, E. A.; Ron'shin, F. V.; Kabov, O. A.

2015-09-01

The two-phase flow in a narrow short horizontal channel with a rectangular cross section is studied experimentally. The channel has a width of 10, 20, or 30 mm and a height of 300 μm. The specifics of formation of such two-phase flows are investigated. It is demonstrated that the regions of bubble and churn flow regimes grow and constrain the region of jet flow as the channel gets wider. The boundaries of the regions of annular and stratified flow regimes remain almost unaltered.

The Missing Link: the Role of Floodplain Tie Channels in Connecting Off River Water Bodies to Lowland Rivers

NASA Astrophysics Data System (ADS)

Rowland, J. C.; Dietrich, W. E.; Day, G.

2005-05-01

Along lowland river systems across the globe the exchange of water, sediment, carbon, nutrients and biota between main stem rivers and off-river water bodies (ORWB) is facilitated by the presence of stable secondary channels referred to here as tie channels. Sixty five percent of the ORWB along the middle Fly River in Papua New Guinea connect to the river through such channels. A similar percentage of the 37 ORWB located between Baton Rouge and Memphis on the lower Mississippi River at one time were linked to the river by tie or batture (as they are locally known) channels. Levee construction and other alterations aimed at flood control or navigation on the Mississippi have left only a handful of lakes connected to the river, of these, most are heavily altered by dredging or other modifications. Tie channels were also once common along major tributaries to the Mississippi, such as the Red River. In the much less disturbed Alaskan environment, tie channels are still common, especially along Birch Creek and the Koyukuk and Black rivers. Our studies on the Mississippi River, in Alaska and in Papua New Guinea indicate that tie channels possess a common channel form that is stable and self-maintaining for hundreds to possibly a thousand years. Tie channels exhibit narrow width to depth ratios (~ 5.5) and consistently scale in cross-sectional dimensions to the size of the lake into which they flow. Variations in river and lake stage drive flow bi-directionally through tie channels. A local high or sill in the bed of tie channels controls the degree and duration of connection between the river and ORWB, with many lakes becoming isolated during periods of low stage. The life-span of a tie channel depends on the rate of sediment loading to the ORWB. Our research indicates that this rate directly corresponds to the sediment loading in the main stem river. Along the Fly River, for example, a 5 to 7 fold increase in the river sediment load has resulted increases of 6 to 17 times in tie channel progradation rates. In a few instances Fly River tie channels have become filled with sediment following the increase in sediment loading. The precise role of tie channels in the ecology of lowland river systems has yet to be quantified, but given their critical role in connecting rivers with floodplain habitats it is likely they provide an important source of refuge, breeding habitat, and biomass production for many aquatic organisms. As restoration efforts increasingly focus on the improving or reestablishing connectivity between lowland rivers and their floodplains, consideration should be given as to whether tie channels are an important missing component of such systems.

Unsteady Heat Transfer in Channel Flow using Small-Scale Vorticity Concentrations Effected by a Vibrating Reed

NASA Astrophysics Data System (ADS)

Hidalgo, Pablo; Glezer, Ari

2011-11-01

Heat transfer enhancement by small-scale vorticity concentrations that are induced within the core flow of a mm-scale heated channel are investigated experimentally. These small-scale motions are engendered by the cross stream vibrations of a streamwise cantilevered reed that spans most of the channel's width. The interactions between the reed the core flow over a range of flow rates lead to the formation, shedding, and advection of time-periodic vorticity concentrations that interact with the wall boundary layers, and increase cross stream mixing of the core flow. Heating of the channel walls is controlled using microfabricated serpentine resistive heaters embedded with streamwise arrays of temperature sensors. It is shown that the actuation disrupts the thermal boundary layers and result in significant enhancement of the local and global heat transfer along the channel compared to the baseline flow in the absence of the reed. The effect of the reed on the cross flow is measured using high resolution particle image velocimetry (PIV), and the reed motion is characterized using a laser-based position sensor. The blockage induced by the presence of the reed and its cross stream motion is characterized using detailed streamwise pressure distributions. Supported by DARPA and UTRC.

Contact behavior modelling and its size effect on proton exchange membrane fuel cell

NASA Astrophysics Data System (ADS)

Qiu, Diankai; Peng, Linfa; Yi, Peiyun; Lai, Xinmin; Janßen, Holger; Lehnert, Werner

2017-10-01

Contact behavior between the gas diffusion layer (GDL) and bipolar plate (BPP) is of significant importance for proton exchange membrane fuel cells. Most current studies on contact behavior utilize experiments and finite element modelling and focus on fuel cells with graphite BPPs, which lead to high costs and huge computational requirements. The objective of this work is to build a more effective analytical method for contact behavior in fuel cells and investigate the size effect resulting from configuration alteration of channel and rib (channel/rib). Firstly, a mathematical description of channel/rib geometry is outlined in accordance with the fabrication of metallic BPP. Based on the interface deformation characteristic and Winkler surface model, contact pressure between BPP and GDL is then calculated to predict contact resistance and GDL porosity as evaluative parameters of contact behavior. Then, experiments on BPP fabrication and contact resistance measurement are conducted to validate the model. The measured results demonstrate an obvious dependence on channel/rib size. Feasibility of the model used in graphite fuel cells is also discussed. Finally, size factor is proposed for evaluating the rule of size effect. Significant increase occurs in contact resistance and porosity for higher size factor, in which channel/rib width decrease.

Drought-induced adaptation of the xylem in Scots pine and pubescent oak.

PubMed

Eilmann, Britta; Zweifel, Roman; Buchmann, Nina; Fonti, Patrick; Rigling, Andreas

2009-08-01

Drought impairs tree growth in the inner-Alpine valleys of Central Europe. We investigated species-specific responses to contrasting water supply, with Scots pine (Pinus sylvestris L.), threatened by drought-induced mortality, and pubescent oak (Quercus pubescens Willd.), showing no connection between drought events and mortality. The two co-occurring tree species were compared, growing either along an open water channel or at a site with naturally dry conditions. In addition, the growth response of Scots pine to a draining of a water channel was studied. We analysed the radial increment for the last 100 years and wood anatomical parameters for the last 45 years. Drought reduced the conduit area of pubescent oak, but increased the radial lumen diameter of the conduits in Scots pine. Both species decreased their radial increment under drought. In Scots pine, radial increment was generally more dependent on water availability than that in pubescent oak. Irrigated trees responded less negatively to high temperature as seen in the increase in the conduit area in pubescent oak and the removal of the limitation of cell division by high temperatures. After irrigation stopped, tree-ring width for Scots pine decreased within 1-year delay, whereas lumen diameter and cell-wall thickness responded with a 4-year delay. Scots pine seemed to optimize the carbon-per-conduit-costs under drought by increasing conduits diameter while decreasing cell numbers. This strategy might lead to a complete loss of tree rings under severe drought and thus to an impairment of water transport. In contrast, in pubescent oak tree-ring width is less affected by summer drought because parts of the earlywood are built in early spring. Thus, pubescent oak might have gradual advantages over pine in today's climate of the inner-Alpine valley.

Flow visualization around an apple with and without bagging

NASA Astrophysics Data System (ADS)

Matsumoto, H.; Kubota, Y.; Ohishi, M.; Mochizuki, O.

2017-04-01

The typhoon often causes the vast damage to drop the apple before harvest. Many apples fall from trees by the strong wind. These apples are usually bagged to protect them from insects and control sun light for the apples colouring while they are ripening on the tree. We directly measured the drag force acting on an apple with and without bagging experimentally to bare the influence of the bagging on the dropping mechanism. There are two interesting results through the experiment: the drag coefficient of a naked apple is smaller than a sphere, and the bagging is a cause of increasing drag coefficient. To know the reason of these results, we visualized flow around the apple with and without bagging by using the hydrogen bubbles method in an open water channel in this study. We found two facts as follows: the hollow on the top of an apple plays reduction of width of the wake of an apple and reason of increasing the wake width is the flow separation from peripheral edge of the bagging.

Growth and analysis of anaerobic wastewater methanogens using microfluidics

NASA Astrophysics Data System (ADS)

Steinhaus, Ben

2005-11-01

A micro-bioreactor (μBR) with a total system volume of 5 μl was developed using microfluidics and used to study the anaerobic waste-water methanogen methanosaeta concilli. The μBR was contained inside of an anaerobic chamber designed to be placed directly under an inverted light microscope while maintaining the reactor under a N2/CO2 gas mixture. Methanogens were cultured for periods of up to 3 months inside channels of varying width. The varying channel widths created varying fluid velocities and hence varying shear-rates inside the μBR. This allowed for direct study of the behavior and response of the anaerobe to varying shear-rates. After completion of the study, fluorescent in situ hybridization (FISH) was performed directly inside the microchannels to allow for further analysis and identification of the methanogens.

Oriented graphene nanoribbons embedded in hexagonal boron nitride trenches

PubMed Central

Chen, Lingxiu; He, Li; Wang, Hui Shan; Wang, Haomin; Tang, Shujie; Cong, Chunxiao; Xie, Hong; Li, Lei; Xia, Hui; Li, Tianxin; Wu, Tianru; Zhang, Daoli; Deng, Lianwen; Yu, Ting; Xie, Xiaoming; Jiang, Mianheng

2017-01-01

Graphene nanoribbons (GNRs) are ultra-narrow strips of graphene that have the potential to be used in high-performance graphene-based semiconductor electronics. However, controlled growth of GNRs on dielectric substrates remains a challenge. Here, we report the successful growth of GNRs directly on hexagonal boron nitride substrates with smooth edges and controllable widths using chemical vapour deposition. The approach is based on a type of template growth that allows for the in-plane epitaxy of mono-layered GNRs in nano-trenches on hexagonal boron nitride with edges following a zigzag direction. The embedded GNR channels show excellent electronic properties, even at room temperature. Such in-plane hetero-integration of GNRs, which is compatible with integrated circuit processing, creates a gapped channel with a width of a few benzene rings, enabling the development of digital integrated circuitry based on GNRs. PMID:28276532

VizieR Online Data Catalog: ALMA survey of Lupus protoplanetary disks. I. (Ansdell+, 2016)

NASA Astrophysics Data System (ADS)

Ansdell, M.; Williams, J. P.; van der Marel, N.; Carpenter, J. M.; Guidi, G.; Hogerheijde, M.; Mathews, G. S.; Manara, C. F.; Miotello, A.; Natta, A.; Oliveira, I.; Tazzari, M.; Testi, L.; van Dishoeck, E. F.; van Terwisga, S. E.

2016-11-01

Our ALMA Cycle 2 observations (Project ID: 2013.1.00220.S) were obtained on 2015 June 14 (AGK-type sources and unknown spectral types) and 2015 June 15 (M-type sources). The continuum spectral windows were centered on 328.3, 340.0, and 341.8GHz with bandwidths of 1.875, 0.938, and 1.875 GHz and channel widths of 15.625, 0.244, and 0.977MHz, respectively. The bandwidth-weighted mean continuum frequency was 335.8GHz (890um). The spectral setup included two windows covering the 13CO and C18O 3-2 transitions; these spectral windows were centered on 330.6 and 329.3GHz, respectively, with bandwidths of 58.594MHz, channel widths of 0.122MHz, and velocity resolutions of 0.11km/s. (3 data files).

Simultaneous frequency stabilization and high-power dense wavelength division multiplexing (HP-DWDM) using an external cavity based on volume Bragg gratings (VBGs)

NASA Astrophysics Data System (ADS)

Hengesbach, Stefan; Klein, Sarah; Holly, Carlo; Witte, Ulrich; Traub, Martin; Hoffmann, Dieter

2016-03-01

Multiplexing technologies enable the development of high-brightness diode lasers for direct industrial applications. We present a High-Power Dense Wavelength Division Multiplexer (HP-DWDM) with an average channel spacing of 1.7 (1.5) nm and a subsequent external cavity mirror to provide feedback for frequency stabilization and multiplexing in one step. The "self-optimizing" multiplexing unit consists of four reflective Volume Bragg Gratings (VBGs) with 99% diffraction efficiency and seven dielectric mirrors to overlay the radiation of five input channels with an adjustable channel spacing of 1-2 nm. In detail, we focus on the analysis of the overall optical efficiency, the change of the beam parameter product and the spectral width. The performance is demonstrated using five 90 μm multimode 9xx single emitters with M2<=17. Because of the feedback the lateral (multimodal) spatial and angular intensity distribution changes strongly and the beam parameter product decreases by a factor of 1.2 to 1.9. Thereby the angular intensity distribution is more affected than the width of the beam waist. The spectral width per emitter decreases to 3-200 pm (FWHM) depending on the injection current and the reflectance of the feedback mirror (0.75%, 1.5%, 4%, 6% or 8%). The overall optical multiplexing efficiency ranges between 77% and 86%. With some modifications (e.g. enhanced AR-coatings) we expect 90-95%.

The Evolution of Riparian Landscape Elements Following Upstream Regulation and Depletion on the Rio Grande

NASA Astrophysics Data System (ADS)

Everitt, B. L.

2006-12-01

In 1915 closure of Elephant Butte Dam in central New Mexico profoundly altered the hydrologic regime of the Rio Grande for 560 km downstream, and set in motion a cascade of interwoven geomorphic, biological, and cultural responses. Geomorphic response included shrinking of the width and depth of the channel, and an increase in sinuosity. Cultural responses included artificial channel modification on 320 km of the river within the boundaries of the original irrigation project, beginning in 1933. The pre-dam river and its flood plain consisted of a mosaic of geomorphic elements that formed a functional riverine landscape, and founded a diverse habitat for the plants, animals, and people that lived there. A preliminary comparison of the modern river with pre-dam topographic mapping permits identification of individual landscape elements, including overflow land (flood plain) both cultivated and uncultivated, with oxbows and back-swamps. The pre-dam channel included a low water thread and un-vegetated flood bars. From pre-dam description and photographs we can assume the usual complement of pools and riffles, point bars and undercut banks. Until dredged in the 1970s, the unmodified reach retained the entire suite of landscape elements, although in somewhat different proportions from the pre-dam river, and remained a functional riparian system. Channel sinuosity increased from 1.45 in 1910 to 1.7 in 1970, thus riverbank habitat increased by 1.17%. In 1970 undercut banks still provided protection for fish, and point bars generated by lateral migration still provided seed beds for pioneer species. The smaller shallower channel raised groundwater beneath the flood plain and retarded flood waves, creating a generally more mesic environment, although the river occasionally dries up, as it did prior to 1915. In contrast, an impoverished suite of landscape elements characterizes the channelized reach. Lateral stability precludes point bars and undercut banks. Bounding levees separate the channel from its former flood plain. All areas are impacted by heavy machinery during periodic channel maintenance. I conclude that the environmental degradation caused by artificial channel modification has far outweighed any generated by upstream hydrologic control.

Twisted Fermi surface of a thin-film Weyl semimetal

NASA Astrophysics Data System (ADS)

Bovenzi, N.; Breitkreiz, M.; O'Brien, T. E.; Tworzydło, J.; Beenakker, C. W. J.

2018-02-01

The Fermi surface of a conventional two-dimensional electron gas is equivalent to a circle, up to smooth deformations that preserve the orientation of the equi-energy contour. Here we show that a Weyl semimetal confined to a thin film with an in-plane magnetization and broken spatial inversion symmetry can have a topologically distinct Fermi surface that is twisted into a figure-8—opposite orientations are coupled at a crossing which is protected up to an exponentially small gap. The twisted spectral response to a perpendicular magnetic field B is distinct from that of a deformed Fermi circle, because the two lobes of a figure-8 cyclotron orbit give opposite contributions to the Aharonov-Bohm phase. The magnetic edge channels come in two counterpropagating types, a wide channel of width β {l}m2\\propto 1/B and a narrow channel of width {l}m\\propto 1/\\sqrt{B} (with {l}m=\\sqrt{{\\hslash }/{eB}} the magnetic length and β the momentum separation of the Weyl points). Only one of the two is transmitted into a metallic contact, providing unique magnetotransport signatures.

Directed collective motion of bacteria under channel confinement

NASA Astrophysics Data System (ADS)

Wioland, H.; Lushi, E.; Goldstein, R. E.

2016-07-01

Dense suspensions of swimming bacteria are known to exhibit collective behaviour arising from the interplay of steric and hydrodynamic interactions. Unconfined suspensions exhibit transient, recurring vortices and jets, whereas those confined in circular domains may exhibit order in the form of a spiral vortex. Here we show that confinement into a long and narrow macroscopic ‘racetrack’ geometry stabilises bacterial motion to form a steady unidirectional circulation. This motion is reproduced in simulations of discrete swimmers that reveal the crucial role that bacteria-driven fluid flows play in the dynamics. In particular, cells close to the channel wall produce strong flows which advect cells in the bulk against their swimming direction. We examine in detail the transition from a disordered state to persistent directed motion as a function of the channel width, and show that the width at the crossover point is comparable to the typical correlation length of swirls seen in the unbounded system. Our results shed light on the mechanisms driving the collective behaviour of bacteria and other active matter systems, and stress the importance of the ubiquitous boundaries found in natural habitats.

Three-dimensional envelope instability in periodic focusing channels

NASA Astrophysics Data System (ADS)

Qiang, Ji

2018-03-01

The space-charge driven envelope instability can be of great danger in high intensity accelerators and was studied using a two-dimensional (2D) envelope model and three-dimensional (3D) macroparticle simulations before. In this paper, we study the instability for a bunched beam using a three-dimensional envelope model in a periodic solenoid and radio-frequency (rf) focusing channel and a periodic quadrupole and rf focusing channel. This study shows that when the transverse zero current phase advance is below 90 ° , the beam envelope can still become unstable if the longitudinal zero current phase advance is beyond 90 ° . For the transverse zero current phase advance beyond 90 ° , the instability stopband width becomes larger with the increase of the longitudinal focusing strength and even shows different structure from the 2D case when the longitudinal zero current phase advance is beyond 90 ° . Breaking the symmetry of two longitudinal focusing rf cavities and the symmetry between the horizontal focusing and the vertical focusing in the transverse plane in the periodic quadrupole and rf channel makes the instability stopband broader. This suggests that a more symmetric accelerator lattice design might help reduce the range of the envelope instability in parameter space.

An affordable modular vehicle radar for landmine and IED detection

NASA Astrophysics Data System (ADS)

Daniels, David; Curtis, Paul; Dittmer, Jon; Hunt, Nigel; Graham, Blair; Allan, Robert

2009-05-01

This paper describes a vehicle mounted 8-channel radar system suitable for buried landmine and IED detection. The system is designed to find Anti Tank (AT) landmines and buried Improvised Explosive Devices (IEDs). The radar uses field-proven ground penetrating radar sub-system modules and is scalable to 16, 32 or 64 channels, for covering greater swathe widths and for providing higher cross track resolution. This offers the capability of detecting smaller targets down to a minimum dimension of 100mm. The current rate of advance of the technology demonstrator is 10 kph; this can be increased to 20 kph where required. The data output is triggered via shaft encoder or via GPS and, for each forward increment; the data output is variable from a single byte per channel through to the 512 samples per channel. Trials using an autonomous vehicle, combined with a COFDM wireless link for data and telemetry back to a base station, have proven successful and the system architecture is described in this paper. The GPR array can be used as a standalone sensor or can be integrated with off-the-shelf software and a metal detection array.

Exploring pre-channelization bar and planform dynamics of a large regulated Alpine River

NASA Astrophysics Data System (ADS)

Zen, Simone; Zolezzi, Guido; Scorpio, Vittoria; Mastronunzio, Marco; Bertoldi, Walter; Comiti, Francesco; Daiprà, Elena

2017-04-01

As a consequence of heavy channelization mostly carried out in the 1800s, the planform and bars morphodynamics of many large European rivers is hardly detectable even from aerial images dating back several decades, because of the marked reduction of the channel width and of the related morphological complexity. However, when available, historical maps can provide quantitative information on the morphology that characterized these rivers before massive human intervention occurred. In this work we focus on a 100 km reach of the Adige - Etsch River, NE, Italy, with the aim of exploring the short-term (some decades) morphological dynamics that might have characterized the pre-channelized river bed and planform in its single-thread reaches before heavy human intervention. To this aim we integrate the application of a morphodynamic analytical model for meandering rivers with irregularly varying curvature and channel width with the multi-temporal analysis of pre-channelization historical maps. The work focuses on the sinuous and meandering reaches once characterized by spatially varying channel width, and presence of alternate, point and mid-channel bars. Challenges in such kind of integrated analysis are posed by the reconstruction of channel - forming streamflow values and of sediment size that may have characterized the river reaches up to nearly three centuries ago prior to heavy regulation. Formative discharge ranges have been obtained as those generating the best geometrical fit between the modeled river bed morphology and the one observed from the maps. Once calibrated by this procedure, the model was fed through the estimated discharge value to compute the longitudinal variability of the outer-bank shear stress, as a proxy for the locations potentially affected by fluvial bank erosion. The historical maps reveal that during the 17th and 18th century, before the massive channelization, the river morphodynamics was already far from being "natural", especially because of distributed, albeit simple engineering structures, like bank protection works, wooden barriers and groynes. Results showed good correspondence between both position of the centroid of the polygons that identified the deposited sediment of the alternate and point bars. Interestingly, the location of near-bank maximum shear stress was often close to the position of the bank structures detected in the historical maps. The satisfactory results obtained from model applications supports the use of analytical morphodynamic models as suitable tools to explore past, otherwise hidden river morphodynamics, especially if integrated with historical sources. The same model could be used, together with more sophisticated numerical tools, to develop possible response scenarios of the present river bed morphology to future restoration actions based on locally giving more room to the river.

Synthesis of Biofluidic Microsystems (SYNBIOSYS)

DTIC Science & Technology

2007-10-01

reaction system. 58 FIGURE 41. The micro reactor is represented by a PFR network model. The calculation of reaction and convection is conducted in...one column of PFRs and the calculation of diffusional mixing is conducted between two columns of PFRs. 59 FIGURE 42. Apply the numerical method of...lines to calculate the diffusion in the channel width direction. Here, we take 10 discretized concentration points in the channel: ci1 - ci10. Points

Low-pressure, high-temperature thermal bonding of polymeric microfluidic devices and their applications for electrophoretic separation

NASA Astrophysics Data System (ADS)

Sun, Yi; Chian Kwok, Yien; Nguyen, Nam-Trung

2006-08-01

A new method for thermally bonding poly(methyl methacrylate) (PMMA) substrates has been demonstrated. PMMA substrates are first engraved by CO2-laser micromachining to form microchannels. Both channel width and depth can be adjusted by varying the laser power and scanning speed. Channel depths from 50 µm to 1500 µm and widths from 150 µm to 400 µm are attained. CO2 laser is also used for drilling and dicing of the PMMA parts. Considering the thermal properties of PMMA, a novel thermal bonding process with high temperature and low bonding pressure has been developed for assembling PMMA sheets. A high bonding strength of 2.15 MPa is achieved. Subsequent inspection of the cross sections of several microdevices reveals that the dimensions of the channels are well preserved during the bonding process. Electroosmotic mobility of the ablated channel is measured to be 2.47 × 10-4 cm2 V-1 s-1. The functionality of these thermally bonded microfluidic substrates is demonstrated by performing rapid and high-resolution electrophoretic separations of mixture of fluorescein and carboxyfluorescein as well as double-stranded DNA ladders (ΦX174-Hae III dsDNA digest). The performance of the CO2 laser ablated and thermally bonded PMMA devices compares favorably with those fabricated by other professional means.

New alternative Mitrofanoff channel based on spiral intestinal lengthening and tailoring.

PubMed

Cervellione, Raimondo M; Hajnal, Daniel; Varga, Gabriella; Rakoczy, George; Kubiak, Rainer; Kaszaki, Jozsef; Boros, Mihaly; Harwood, Rachel; Dickson, Alan P; Cserni, Tamas

2015-06-01

The occasional lack of appendix and the increasing use of the Malone anterograde continence enema (MACE) procedure have expanded the need for alternative Mitrofanoff channels. The Monti procedure does not always provide adequate length, the anastomosis of the double Monti, and the potential kink of the Casale channel is not ideal for smooth catheterisation. We tested the concept of spiral intestinal lengthening and tailoring (SILT), we developed originally for short bowel syndrome, to create a long and straight alternative Mitrofanoff channel (Figure). After ethical approval five mini-pigs underwent spiral intestinal lengthening and tailoring (SILT) without any previous bowel dilatation procedure. (Mean bowel width was 20.5 ± 0.57 mm). The spiral line was marked on a 6-8-cm-long ileum approximately 15 mm apart with a 60° angle to the longitudinal axis of the bowel. When the incision was completed, the mesentery was incised perpendicularly where the spiral incision line met the mesentery. The maximum length segment hanging on a single 1.5-cm-wide well-vascularised mesentery was detached. The capillary red blood cell velocity (RBCV) and perfusion rate (PR) was measured at the edges of the opened bowel strip by in vivo microscopy using orthogonal polarising spectral imaging (Cytoscan A/R, Cytometrics, Philadelphia, PA, USA). The bowel strips have been reconstructed in spiral fashion over a 12F catheter and were implanted into the bladder. Viability, patency, and microcirculation were assessed 4 weeks later. Conventional microscopy with HE staining was performed. The mean length of the spiral channel (100 ± 26.4 mm) was longer than could have been achieved with the double Monti or Casale procedure (4 times the bowel width). A 17% and 8.3% reduction was measured in the median values of the RBCV and the PR at the edges of the bowel strip at the primary surgery. All implanted channels remained viable, straight, patent, and easily catheterisable after 4 weeks, with full recovery of the RBCV and PR. The histology showed no necrosis or fibrosis. The SILT concept is suitable for creating a long and straight alternative Mitrofanoff channel. However, the SILT technique has been reported to be successful in the clinical practice to tailor and lengthen dilated short bowel; in this study we first applied this technique on normal calibre intestine to create long alternative Mitrofanoff channel. The use of an animal model and the relative short-term observation are the limitations of this study. Copyright © 2015 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

Laser-hole boring into overdense plasmas measured with soft X-Ray laser probing

PubMed

Takahashi; Kodama; Tanaka; Hashimoto; Kato; Mima; Weber; Barbee; Da Silva LB

2000-03-13

A laser self-focused channel formation into overdense plasmas was observed using a soft x-ray laser probe system with a grid image refractometry (GIR) technique. 1.053 &mgr;m laser light with a 100 ps pulse duration was focused onto a preformed plasma at an intensity of 2x10(17) W/cm (2). Cross sections of the channel were obtained which show a 30 &mgr;m diameter in overdense plasmas. The channel width in the overdense region was kept narrow as a result of self-focusing. Conically diverging density ridges were also observed along the channel, indicating a Mach cone created by a shock wave due to the supersonic propagation of the channel front.

Basin Hydrology and Substrate Controls on Mountain Stream Morphology: Highlands of Southeastern West Virginia

NASA Astrophysics Data System (ADS)

Burks, T. W.; Springer, G. S.

2004-12-01

Evolution of mountain drainage basins across a broad spectrum of geologic, tectonic, and climatic conditions is an active area of investigation in the field of fluvial geomorphology. Mountain streams are typified by steep channel gradients (>0.002), high channel roughness, rapid changes in drainage area, and high spatial and low temporal variability in channel morphology, leading to complexities in landscape modeling relative to their lowland counterparts. Factors driving this recent investigative trend are the refinement and generation of digital topographic data and terrain analysis software, and more importantly, the demand for a multidiscipline approach to the assessment, restoration, and management of entire watersheds. A significant volume of research has been conducted in mountain drainage basins of the western United States, with particular attention paid to tectonically active regions of the Pacific Northwest, which also contain federally listed threatened and endangered salmonid populations. Brook trout (Salvelinus fontinalis), native to the highlands of the eastern margin of the Appalachian Plateau are impacted by acid rain deposition; however, geomorphic research into landscape modeling, applicable to restoration and management of lotic ecosystems of the eastern United States, is comparatively lacking. This current research explores the potential for modeling channel morphology in mountain streams; specifically, how downstream trends in channel substrate resistance and unit stream power effect the partitioning of mountain stream morphology along and downstream of the fluvial/colluvial transition. In order to address this issue, two mountain drainage basins in the headwaters of the Gauley River watershed on the Appalachian Plateau of southeastern West Virginia were chosen. The westerly flowing Cranberry (250 sqkm) and Cherry (429 sqkm) rivers incise gently northwestward dipping Carboniferous-aged strata (shale, minor coal, siltstone, sandstone, and conglomerate), with a large percentage of both drainages managed as the Monongahela National Forest. A total of 68 reach-scale (10-20 channel widths) channel surveys were completed in which reach gradient, average bankfull channel widths, and bed surface grain size data were determined. This information was synthesized with data extracted from 10-meter digital elevation models using both RiverTools v. 2.4 and ArcGIS Desktop 8.3 terrain analysis software packages. Surveyed channel reach gradients range from (0.002-0.150 m/m) and are characterized by pool-riffle to cascade and step-pool morphologies, though observed morphology succession is atypical of an equilibrated system. Partitioning in channel morphology succession correlates with both changes in lithology (e.g. siltstone to conglomerate) and the extent of headwater debris flow activity, which reflects a shift in the balance between driving and resisting forces as stream size increases.

Increase in cortical pyramidal cell excitability accompanies depression-like behavior in mice: a transcranial magnetic stimulation study.

PubMed

Sun, Peng; Wang, Furong; Wang, Li; Zhang, Yu; Yamamoto, Ryo; Sugai, Tokio; Zhang, Qing; Wang, Zhengda; Kato, Nobuo

2011-11-09

Clinical evidence suggests that cortical excitability is increased in depressives. We investigated its cellular basis in a mouse model of depression. In a modified version of forced swimming (FS), mice were initially forced to swim for 5 consecutive days and then were treated daily with repetitive transcranial magnetic stimulation (rTMS) or sham treatment for the following 4 weeks without swimming. On day 2 through day 5, the mice manifested depression-like behaviors. The next and last FS was performed 4 weeks later, which revealed a 4 week maintenance of depression-like behavior in the sham mice. In slices from the sham controls, excitability in cingulate cortex pyramidal cells was elevated in terms of membrane potential and frequencies of spikes evoked by current injection. Depolarized resting potential was shown to depend on suppression of large conductance calcium-activated potassium (BK) channels. This BK channel suppression was confirmed by measuring spike width, which depends on BK channels. Chronic rTMS treatment during the 4 week period significantly reduced the depression-like behavior. In slices obtained from the rTMS mice, normal excitability and BK channel activity were recovered. Expression of a scaffold protein Homer1a was reduced by the FS and reversed by rTMS in the cingulate cortex. Similar recovery in the same behavioral, electrophysiological, and biochemical features was observed after chronic imipramine treatment. The present study demonstrated that manifestation and disappearance of depression-like behavior are in parallel with increase and decrease in cortical neuronal excitability in mice and suggested that regulation of BK channels by Homer1a is involved in this parallelism.

Topography Battles Surface Texture: An Experimental Study of Pool-riffle Formation

NASA Astrophysics Data System (ADS)

Chartrand, S. M.; Hassan, M. A.; Jellinek, M.

2016-12-01

Pool-riffles are perhaps the most common streambed shape found in streams and rivers, and not surprisingly, they are essential to salmon ecology, and are a central focus of many restoration actions. Yet, when an applied earth scientist or engineer is faced with developing a pool-riffle design, there is a lack of clear and rigorously developed design guidelines. Given the volumes of money spent annually within the restoration industry, this is a real problem. Recognition of this problem is growing, however, and an increasing level of attention has been directed to questions of pool-riffle formation in the past decade. At this point and given certain landscape characteristics, it is well established that streamwise gradients in channel width are associated with pool-riffles. Specifically, pools are associated with negative gradients in width, and riffles with positive gradients. Importantly, these associations have now been documented from field-derived data, as well as via experimental and numerical investigations. There is much to build from the present knowledge base, and central to this are questions related to (a) how pool-riffles evolve during the formative process, (b) what are the basic set of ingredients necessary for pool-riffle formation within systems characterized by relatively non-erodible channel margins, and (c) do pool-riffles persist, once formed, under a broad range of forcing conditions? We have completed four physical experiments examining the process and evolution of pool-riffle formation under a large range of upstream boundary, as well as physical channel conditions. We will report on two of the completed experiments. Our work will highlight two new non-dimensional channel evolution numbers, derived to help describe and characterize bedform development, as well as response to perturbations from near-equilibrium conditions. The channel evolution numbers lay the foundation for development of a new regime diagram, which quantifies the basic ingredients needed to drive pool-riffle formation, as well as formation of other types of gravel bedforms. We believe our work holds promise for application in identifying suitable conditions for pool-riffle construction, and natural maintenance over typical restoration project time frames.

The Topographic Design of River Channels for Form-Process Linkages.

PubMed

Brown, Rocko A; Pasternack, Gregory B; Lin, Tin

2016-04-01

Scientists and engineers design river topography for a wide variety of uses, such as experimentation, site remediation, dam mitigation, flood management, and river restoration. A recent advancement has been the notion of topographical design to yield specific fluvial mechanisms in conjunction with natural or environmental flow releases. For example, the flow convergence routing mechanism, whereby shear stress and spatially convergent flow migrate or jump from the topographic high (riffle) to the low point (pool) from low to high discharge, is thought to be a key process able to maintain undular relief in gravel bedded rivers. This paper develops an approach to creating riffle-pool topography with a form-process linkage to the flow convergence routing mechanism using an adjustable, quasi equilibrium synthetic channel model. The link from form to process is made through conceptualizing form-process relationships for riffle-pool couplets into geomorphic covariance structures (GCSs) that are then quantitatively embedded in a synthetic channel model. Herein, GCSs were used to parameterize a geometric model to create five straight, synthetic river channels with varying combinations of bed and width undulations. Shear stress and flow direction predictions from 2D hydrodynamic modeling were used to determine if scenarios recreated aspects of the flow convergence routing mechanism. Results show that the creation of riffle-pool couplets that experience flow convergence in straight channels requires GCSs with covarying bed and width undulations in their topography as supported in the literature. This shows that GCSs are a useful way to translate conceptualizations of form-process linkages into quantitative models of channel form.

Tharsis Flood Features

NASA Technical Reports Server (NTRS)

2005-01-01

17 July 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows channels carved by catastrophic floods in the Tharsis region of Mars. This area is located northwest of the volcano, Jovis Tholus, and east of the large martian volcano, Olympus Mons. The terrain is presently mantled with fine dust.

Location near: 20.8oN, 118.8oW Image width: width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Autumn

Total width of 125 GeV Higgs boson.

PubMed

Barger, Vernon; Ishida, Muneyuki; Keung, Wai-Yee

2012-06-29

By using the LHC and Tevatron measurements of the cross sections to various decay channels relative to the standard model Higgs boson, the total width of the putative 125 GeV Higgs boson is determined as 6.1(-2.9)(+7.7) MeV. We describe a way to estimate the branching fraction for the Higgs-boson decay to dark matter. We also discuss a no-go theorem for the γγ signal of the Higgs boson at the LHC.

Control of Sediment Availability on the Path of Channel Recovery in Bedload-Dominated Rivers

NASA Astrophysics Data System (ADS)

Doyle, H.; Renshaw, C. E.; Magilligan, F. J.

2015-12-01

Following a disturbance, a channel can recover to an equilibrium form by adjusting its slope, width, depth, grain size, or some combination of these dimensions that define the recovery path. In this study we relate the channel recovery path to the quantity and caliber of sediment introduced due to dam construction/removal or erosion caused by flooding. We suggest that the recovery path of a channel depends on the availability of sediment of a size that is transported as bedload during bankfull flows (the "mobile fraction"). We define a ratio, S*, of the sediment volume added to the channel because of the disturbance to the average annual sediment flux. We compare S* values to the recovery path of New England gravel-bedded streams following two dam emplacements and removals and flooding related to Tropical Storm Irene. Pelham Dam in Pelham, MA (removed 2012) and Kendrick Dam in Pittsford, VT (removed 2014) were on similar streams: drainage areas ~25 km2, slopes 1-2%, and bankfull widths ~10 m. Sediment was excavated from both impoundments prior to removal, resulting in lower S* values. Irene-affected study sites are on ~10 gravel-bedded streams in VT, NH, and MA. Sediment input at these sites is due to bank failures and landslides, many of which continue to supply sediment to the channel four years after flooding. To track recovery we collected annual topographic and sediment size data and calculated Shields numbers to determine if channels had reached an equilibrium form. We define equilibrium for bedload rivers as Shields numbers at bankfull discharge equal to that required to initiate bedload transport. Following dam emplacements the channels failed to recover because mobile sediment was unavailable. Fining dominated the recovery at Irene-affected sites (~10% reduction in sediment size) and dam removal sites (up to 30-60% reduction) with little post-disturbance change in channel geometry, possibly due to the limited mobile fraction.

Using High-Resolution Comparison of Bedrock Properties and Channel Morphology to Empirically Characterize Erodibility in Fluvial Settings

NASA Astrophysics Data System (ADS)

Chilton, K.; Spotila, J. A.

2017-12-01

Bedrock erodibility exerts a primary control on landscape evolution and fluvial morphodynamics, but the relationships between erodibility and the many factors that influence it (rock strength, spacing and orientation of discontinuities, weathering susceptibility, erosive process, etc.) remain poorly defined. This results in oversimplification of erodibility in landscape evolution models, the primary example being the stream power incision model, which groups together factors which may influence erodibility into a single coefficient. There is therefore need to better define how bedrock properties influence erodibility and, in turn, channel form and evolution. This study seeks to deconvolve the relationships between bedrock material properties and erodibility by quantifying empirical relationships between substrate characteristics and bedrock channel morphology (slope, steepness index, width, form) at a high spatial resolution (5-10 m scale) in continuous and mixed alluvial-bedrock channels. We specifically focus on slowly eroding channels with minimal evidence for landscape transience, such that variations in channel morphology are mainly due to bedrock properties. We also use channels cut into sedimentary rock, which exhibit extreme variation (yet predictability and continuity) in discontinuity spacing. Here we present preliminary data comparing the morphology and bedrock properties of 1st through 4th order channels in the tectonically inactive Valley and Ridge province of the Appalachian Mountains, SW Virginia. Field surveys of channel slope, width, substrate, and form consist of 0.5 km long, continuous stream reaches through different intervals of tilted Paleozoic siliciclastic stratigraphy. Some surveys exhibit nearly complete bedrock exposure, whereas others are predominantly mixed, with localized bedrock reaches in high-slope knickzones. We statistically analyze relationships between fluvial morphology and lithology, strength (based on field and laboratory measurements), and discontinuity spacing and orientation. Results are informative for models of landscape evolution, and specifically provide insight into the controls on erosive process dominance (i.e., plucking vs. abrasion) and on the development and evolution of knickpoints in non-transient settings.

Using Remote Sensing and High-Resolution Digital Elevation Models to Identify Potential Erosional Hotspots Along River Channels During High Discharge Storm Events

NASA Astrophysics Data System (ADS)

Orland, E. D.; Amidon, W. H.

2017-12-01

As global warming intensifies, large precipitation events and associated floods are becoming increasingly common. Channel adjustments during floods can occur by both erosion and deposition of sediment, often damaging infrastructure in the process. There is thus a need for predictive models that can help managers identify river reaches that are most prone to adjustment during storms. Because rivers in post-glacial landscapes often flow over a mixture of bedrock and alluvial substrates, the identification of bedrock vs. alluvial channel reaches is an important first step in predicting vulnerability to channel adjustment during flood events, especially because bedrock channels are unlikely to adjust significantly, even during floods. This study develops a semi-automated approach to predicting channel substrate using a high-resolution LiDAR-derived digital elevation model (DEM). The study area is the Middlebury River in Middlebury, VT-a well-studied watershed with a wide variety of channel substrates, including reaches with documented channel adjustments during recent flooding events. Multiple metrics were considered for reference—such as channel width and drainage area—but the study utilized channel slope as a key parameter for identifying morphological variations within the Middlebury River. Using data extracted from the DEM, a power law was fit to selected slope and drainage area values for each branch in order to model idealized slope-drainage area relationships, which were then compared with measured slope-drainage area relationships. Differences in measured slope minus predicted slope (called delta-slope) are shown to help predict river channel substrate. Compared with field observations, higher delta-slope values correlate with more stable, boulder rich channels or bedrock gorges; conversely the lowest delta-slope values correlate with flat, sediment rich alluvial channels. The delta-slope metric thus serves as a reliable first-order predictor of channel substrate in the Middlebury River, which in turn can be used to help identify local reaches that are most vulnerable to channel adjustment during large flood events.

Mobility of large woody debris (LWD) jams in a low gradient channel

NASA Astrophysics Data System (ADS)

Curran, Joanna C.

2010-04-01

Mobility of large woody debris (LWD) in low gradient channels is an important but often overlooked transport process. The majority of studies on LWD have focused on its role in geomorphic and ecologic river processes. When jams extend across the width of the channel, they have the potential to retain sediment and alter the channel profile. When jams obstruct only a portion of the channel, they can re-direct flow, altering patterns of scour and deposition. The boundary complexity created by LWD has a recognized role in riverine ecosystems which has led to programs of replacing LWD in-channel corridors where it was previously removed. Although LWD jams are common in rivers around the world, they have been studied most intensely in steep, forested channel reaches where they are often found to be stable channel features. It is not fully known how much of the information on LWD from steep forested channels will transfer to other channel types. Whereas it may be reasonable to assume that the ecological benefits of LWD are similar in low gradient channels, research has shown that a much higher rate of LWD transport occurs in low gradient channels, with jams mobilized on timescales of 10 0-10 2 years. This study evaluates the distribution and mobility of LWD over 72 km of the San Antonio River, a low gradient channel in southeast Texas. LWD jam locations were identified for 2003 and 2007 using a combination of aerial photography and field mapping. Each jam was cataloged according to its location in the channel cross-section and the amount of channel area blocked. During the four-year period, all the LWD jams were mobilized, including those jams extending across the channel width. Although easily mobilized, 34 jams re-form in the same locations, creating 34 channel locations with persistent LWD jams. Data from the San Antonio River are applied to two models developed to predict LWD mobility and transport distances to assess the applicability of each model to a low gradient channel. The locations of stable (or recurring) LWD jams were matched to model results where predicted LWD transport distances were equal to measured LWD jam spacing. Model results showed good agreement with the mean and median spacing of LWD jams when given input parameters specific to the channel and wood species. The ability to predict where LWD jams will persist over time in a low gradient channel has application in watershed management. Persistent LWD jams can exert a greater influence on channel morphology and may require active management.

Large wood recruitment and transport during a severe flash flood in North-western Italy

NASA Astrophysics Data System (ADS)

Lucía, Ana; Comiti, Francesco; Borga, Marco; Cavalli, Marco; Marchi, Lorenzo

2013-04-01

Understanding and modelling the dynamics of large wood (LW) in rivers during flood events has spurred a great deal of research in recent years. Whereas most of the research on LW has focused on its spatial distribution and geomorphologic role at longer time scales, only few studies have documented the effect of high-magnitude flash floods on LW recruitment, transport and deposition. On October 25th2011, the Magra river basin (North-western Italy) was hit by an extreme meteorological event, with hourly rainrates up to 130 mm h-1 and event rain accumulations up to 540 mm. Such large rainfall intensities originated flash floods in the main river channels and in some of the tributaries, with unit peak discharges up to around 20 m3s-1km-2 in catchments of 10-20 km2, causing severe damages and loss of lives. Numerous landslides were triggered and the morphology of the tributaries was highly affected in response to intense lateral and vertical channel dynamics. Besides, many bridges were partly or fully clogged by LW jams. A post-floodsurvey was carried out in November 2011 and February 2012 along four of the tributaries most severely affected by this event. The total length of surveyed channels is 9.5 km. These channels were divided into reaches of similar morphological characteristics (slope, width, vegetation cover), and in every reach the volume of LW deposited was estimated by a combination of field surveys and interpretation of aerial photos. In addition, LW recruited from hillslopes and floodplains was estimated by comparing pre and post-event orthophotos. Preliminary results show very high rates of LW recruitment (1127 m3km-1 on average ranging from 569-2001 m3km-1) along the analysed channels, the majority (about 80%) stemming from floodplain erosion and the rest from the colluvial processes (predominantly landslides). Channels width has increased on average 10 times (ranging from 4 to 23 times). Despite the large variability among the channels, LW dynamics seems to be related to reach characteristics. In fact, LW deposition was higher - and LW recruitment was smaller - in the wider reaches, and the presence of newly-formed islands or even of single standing trees was key in increasing the trapping efficiency of a reach. Also, the steeper the channel, the lesser is LW deposition and the larger is LW supply. Finally both LW recruitment and deposition show a positive relation with drainage area (for basins > 10 km2). These observations suggest a conceptual model for LW dynamics in mountain rivers different from others recently put forward that have analysed LW storage data alone, at few snapshots in time long after the occurrence of extreme events like the one described here. The lessons learned from this event may be useful for a management of mountain catchments which should explicitly take into account the crucial role of LW during extreme events, especially for its interaction with infrastructures.

Effect of active-layer composition and structure on device performance of coplanar top-gate amorphous oxide thin-film transistors

NASA Astrophysics Data System (ADS)

Yue, Lan; Meng, Fanxin; Chen, Jiarong

2018-01-01

The thin-film transistors (TFTs) with amorphous aluminum-indium-zinc-oxide (a-AIZO) active layer were prepared by dip coating method. The dependence of properties of TFTs on the active-layer composition and structure was investigated. The results indicate that Al atoms acted as a carrier suppressor in IZO films. Meanwhile, it was found that the on/off current ratio (I on/off) of TFT was improved by embedding a high-resistivity AIZO layer between the low-resistivity AIZO layer and gate insulator. The improvement in I on/off was attributed to the decrease in off-state current of double-active-layer TFT due to an increase in the active-layer resistance and the contact resistance between active layer and source/drain electrode. Moreover, on-state current and threshold voltage (V th) can be mainly controlled through thickness and Al content of the low-resistivity AIZO layer. In addition, the saturation mobility (μ sat) of TFTs was improved with reducing the size of channel width or/and length, which was attributed to the decrease in trap states in the semiconductor and at the semiconductor/gate-insulator interface with the smaller channel width or/and shorter channel length. Thus, we can demonstrate excellent TFTs via the design of active-layer composition and structure by utilizing a low cost solution-processed method. The resulting TFT, operating in enhancement mode, has a high μ sat of 14.16 cm2 V-1 s-1, a small SS of 0.40 V/decade, a close-to-zero V th of 0.50 V, and I on/off of more than 105.

Synthesis of quantum dots via microreaction: structure optimization for microreactor system

NASA Astrophysics Data System (ADS)

Yang, Hongwei; Luan, Weiling; Cheng, Rui; Chu, Haijian; Tu, Shan-tung

2011-08-01

Microreactor systems existed as a powerful tool for the continuous synthesis of quantum dots. However, the lack of structure optimization for the discrete units led to empirical determination of the length scale, and the properties of the formed products varied in different cases. In this article, the optimizations for the micromixer volume and capillary diameter were presented based on the synthesis of CdSe nanocrystals (NCs). Spectra investigation revealed that the application of a small convective mixer of 36 μL led to 1/3 increase of CdSe concentration in the crude solution. The enhanced mixing of the precursors in this case was also demonstrated favorable to achieve CdSe NCs with narrow PL width. Fast heating and uniform reaction condition achieved in a narrow channel favored the preparation of high quality CdSe NCs under short residence time. However, the application of wide channel did not necessarily result in CdSe NCs with poor quality. Here, we demonstrated that high-quality CdSe NCs with narrow full width at half maximum (FWHM) as 32 nm and high quantum yield (QY) 34.7% could be prepared using an 844 μm inner diameter capillary. Based on the obtained results, the scaled-up synthesis of CdSe NCs was demonstrated, and a high quantity of 0.8 g dry CdSe NCs powder (3.5 nm, σ 8.2%) was obtained within 1 h.

The effect of feedback-controlled divertor nitrogen seeding on the boundary plasma and power exhaust channel width in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Labombard, B.; Brunner, D.; Kuang, A. Q.; McCarthy, W.; Terry, J. L.

2017-10-01

The scrape-off layer (SOL) power channel width, λq, is projected to be 0.5 mm in power reactors, based on multi-machine measurements of divertor target heat fluxes in H-mode at low levels of divertor dissipation. An important question is: does λq change with the level of divertor dissipation? We report results in which feedback controlled nitrogen seeding in the divertor was used to systematically vary divertor dissipation in a series of otherwise identical L-mode plasmas at three plasma currents: 0.55, 0.8 and 1.1 MA. Outer midplane profiles were recorded with a scanning Mirror Langmuir Probe; divertor plasma conditions were monitored with `rail' Langmuir probe and surface thermocouple arrays. Despite an order of magnitude reduction in divertor target heat fluxes (q// 400 MW m-2 to 40 MW m-2) and corresponding change in divertor regime from sheath-limited through high-recycling to near-detached, the upstream electron temperature profile is found to remain unchanged or to become slightly steeper in the near SOL and to drop significantly in the far SOL. Thus heat in the SOL appears to take advantage of this impurity radiation `heat sink' in the divertor by preferentially draining via the narrow (and perhaps an increasingly narrow) λq of the near SOL. Supported by USDoE award DE-FC02-99ER54512.

Consequences of broad auditory filters for identification of multichannel-compressed vowels

PubMed Central

Souza, Pamela; Wright, Richard; Bor, Stephanie

2012-01-01

Purpose In view of previous findings (Bor, Souza & Wright, 2008) that some listeners are more susceptible to spectral changes from multichannel compression (MCC) than others, this study addressed the extent to which differences in effects of MCC were related to differences in auditory filter width. Method Listeners were recruited in three groups: listeners with flat sensorineural loss, listeners with sloping sensorineural loss, and a control group of listeners with normal hearing. Individual auditory filter measurements were obtained at 500 and 2000 Hz. The filter widths were related to identification of vowels processed with 16-channel MCC and with a control (linear) condition. Results Listeners with flat loss had broader filters at 500 Hz but not at 2000 Hz, compared to listeners with sloping loss. Vowel identification was poorer for MCC compared to linear amplification. Listeners with flat loss made more errors than listeners with sloping loss, and there was a significant relationship between filter width and the effects of MCC. Conclusions Broadened auditory filters can reduce the ability to process amplitude-compressed vowel spectra. This suggests that individual frequency selectivity is one factor which influences benefit of MCC, when a high number of compression channels are used. PMID:22207696

A novel 2D silicon nano-mold fabrication technique for linear nanochannels over a 4 inch diameter substrate

PubMed Central

Yin, Zhifu; Qi, Liping; Zou, Helin; Sun, Lei

2016-01-01

A novel low-cost 2D silicon nano-mold fabrication technique was developed based on Cu inclined-deposition and Ar+ (argon ion) etching. With this technique, sub-100 nm 2D (two dimensional) nano-channels can be etched economically over the whole area of a 4 inch n-type <100> silicon wafer. The fabricating process consists of only 4 steps, UV (Ultraviolet) lithography, inclined Cu deposition, Ar+ sputter etching, and photoresist & Cu removing. During this nano-mold fabrication process, we investigated the influence of the deposition angle on the width of the nano-channels and the effect of Ar+ etching time on their depth. Post-etching measurements showed the accuracy of the nanochannels over the whole area: the variation in width is 10%, in depth it is 11%. However, post-etching measurements also showed the accuracy of the nanochannels between chips: the variation in width is 2%, in depth it is 5%. With this newly developed technology, low-cost and large scale 2D nano-molds can be fabricated, which allows commercial manufacturing of nano-components over large areas. PMID:26752559

Interference effect on a heavy Higgs resonance signal in the γ γ and Z Z channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Jeonghyeon; Yoon, Yeo Woong; Jung, Sunghoon

2016-03-24

The resonance-continuum interference is usually neglected when the width of a resonance is small compared to the resonance mass. We reexamine this standard by studying the interference effects in high-resolution decay channels, γγ and ZZ, of the heavy Higgs boson H in nearly aligned two-Higgs-doublet models. For the H with a sub-percent width-to-mass ratio, we find that, in the parameter space where the LHC 14 TeV ZZ resonance search can be sensitive, the interference effects can modify the ZZ signal rate by O(10)% and the exclusion reach by O(10) GeV. In other parameter space where the ZZ or γγ signalmore » rate is smaller, the LHC 14 TeV reach is absent, but a resonance shape can be much more dramatically changed. In particular, the γγ signal rate can change by O(100)%. Relevant to such parameter space, we suggest variables that can characterize a general resonance shape. Furthermore, we also illustrate the relevance of the width on the interference by adding nonstandard decay modes of the heavy Higgs boson.« less

Geomorphic response to flow regulation and channel and floodplain alteration in the gravel-bedded Cedar River, Washington, USA

USGS Publications Warehouse

Gendaszek, Andrew S.; Magirl, Christopher S.; Czuba, Christiana R.

2012-01-01

Decadal- to annual-scale analyses of changes to the fluvial form and processes of the Cedar River in Washington State, USA, reveal the effects of flow regulation, bank stabilization, and log-jam removal on a gravel-bedded river in a temperate climate. During the twentieth century, revetments were built along ~ 60% of the lower Cedar River's length and the 2-year return period flow decreased by 47% following flow regulation beginning in 1914. The formerly wide, anastomosing channel narrowed by over 50% from an average of 47 m in 1936 to 23 m in 1989 and became progressively single threaded. Subsequent high flows and localized revetment removal contributed to an increase in mean channel width to about 34 m by 2011. Channel migration rates between 1936 and 2011 were up to 8 m/year in reaches not confined by revetments or valley walls and less than analysis uncertainty throughout most of the Cedar River's length where bank armoring restricted channel movement. In unconfined reaches where large wood and sediment can be recruited, contemporary high flows, though smaller in magnitude than preregulation high flows, form and maintain geomorphic features such as pools, gravel bars, and side channels. Reaches confined by revetments remain mostly unmodified in the regulated flow regime. While high flows are important for maintaining channel dynamics in the Cedar River, their effectiveness is currently reduced by revetments, limited sediment supply, the lack of large wood available for recruitment to the channel, and decreased magnitude since flow regulation.

Of Magic Carpets, Rolling Snowballs, and Sleeping Dragons: an Energetics-based Classification for Hillslope/channel Interactions

NASA Astrophysics Data System (ADS)

Grant, G.; Cashman, K.; O'Connor, J.

2007-12-01

Interactions between hillslopes and channels can include a diverse range of geophysical processes, including debris flows, landslides, water floods, and volcanic flows. Each has its own characteristic time-energy trajectory. In some cases the energy of an event increases as it propagates through a landscape, primarily through the addition of mass and momentum; examples of these"rolling snowball" include the initiation and runout phases of volcanic lahars, avalanches, and debris flows. In other cases, loss of both mass and momentum from a moving body or fluid causes the energy of an event to dissipate with distance, similar to the unwinding of a rug; examples of these "magic carpets" include the depositional phases of lahars, pyroclastic flows, lava flows, and debris flows. Both snowballs and carpets leave distinctive imprints or tracks on the landscape that reflect the resultant mass flux from hill slope to channel. The efficiency of this mass transfer depends on the width and slope of the receiving channel and the rheological properties of the transported material. At one extreme, the channel easily accommodates mass flux from the slope, sometimes accompanied by fractionation into constituent phases. At the other extreme, mass from the hill slope can inundate and block the channel; these "sleeping dragons" modulate subsequent mass transfer down channel by changing the channel profile and bed properties. They also have the potential to "wake up" suddenly as mass failure and/or outbreak floods. Hazard prediction requires that the time-energy trajectory of each type of event be assessed; here we suggest some first order controls.

Design and synthesis of guest-host nanostructures to enhance ionic conductivity across nanocomposite membranes

DOEpatents

Hu, Michael Z [Knoxville, TN; Kosacki, Igor [Oak Ridge, TN

2010-01-05

An ion conducting membrane has a matrix including an ordered array of hollow channels and a nanocrystalline electrolyte contained within at least some or all of the channels. The channels have opposed open ends, and a channel width of 1000 nanometers or less, preferably 60 nanometers or less, and most preferably 10 nanometers or less. The channels may be aligned perpendicular to the matrix surface, and the length of the channels may be 10 nanometers to 1000 micrometers. The electrolyte has grain sizes of 100 nanometers or less, and preferably grain sizes of 1 to 50 nanometers. The electrolyte may include grains with a part of the grain boundaries aligned with inner walls of the channels to form a straight oriented grain-wall interface or the electrolyte may be a single crystal. In one form, the electrolyte conducts oxygen ions, the matrix is silica, and the electrolyte is yttrium doped zirconia.

A large 2D PSD for thermal neutron detection

NASA Astrophysics Data System (ADS)

Knott, R. B.; Smith, G. C.; Watt, G.; Boldeman, J. W.

1997-02-01

A 2D PSD based on a MWPC has been constructed for a small angle neutron scattering instrument. The active area of the detector was 640 × 640 mm 2. To meet the specifications for neutron detection efficiency and spatial resolution, and to minimise parallax, the gas mixture was 190 kPa 3He plus 100 kPa CF 4, and the active volume had a thickness of 30 mm. The design maximum neutron count rate of the detector was 10 5 events per secod. The (calculated) neutron detection efficiency was 60% for 2 Å neutrons and the (measured) neutron energy resolution on the anode grid was typically 20% (fwhm). The location of a neutron detection event within the active area was determined using the wire-by-wire method: the spatial resolution (5 × 5 mm 2) was thereby defined by the wire geometry. A 16-channel charge-sensitive preamplifier/amplifier/comparator module has been developed with a channel sensitivity of 0.1 V/fC, noise line width of 0.4 fC (fwhm) and channel-to-channel cross-talk of less than 5%. The Proportional Counter Operating System (PCOS III) (LeCroy Corp, USA) was used for event encoding. The ECL signals produced by the 16 channel modules were latched in PCOS III by a trigger pulse from the anode and the fast encoders produce a position and width for each event. The information was transferred to a UNIX workstation for accumulation and online display.

Co-evolution of Riparian Vegetation and Channel Dynamics in an Aggrading Braided River System, Mount Pinatubo, Philippines

NASA Astrophysics Data System (ADS)

Gran, K. B.; Michal, T.

2014-12-01

Increased bank stability by riparian vegetation in braided rivers can decrease bed reworking rates and focus the flow. The magnitude of influence and resulting channel morphology are functions of vegetation strength vs. channel dynamics, a concept encapsulated in a dimensionless ratio between timescales for vegetation growth and channel reworking known as T*. We investigate this relationship in an aggrading braided river at Mount Pinatubo, Philippines, and compare results to numerical and physical models. Gradual reductions in post-eruption sediment loads have reduced bed reworking rates, allowing vegetation to persist year-round and impact channel dynamics on the Pasig-Potrero and Sacobia Rivers. From 2009-2011, we collected data detailing vegetation extent, type, density, and root strength. Incorporating these data into RipRoot and BSTEM models shows cohesion due to roots increased from zero in unvegetated conditions to >10.2 kPa in densely-growing grasses. Field-based parameters were incorporated into a cellular model comparing vegetation growth and sediment mobility effects on braided channel dynamics. The model shows that both low sediment mobility and high vegetation strength lead to less active systems, reflecting trends observed in the field. An estimated T* between 0.8 - 2.3 for the Pasig-Potrero River suggests channels were mobile enough to maintain the braidplain width clear of vegetation and even experience slight gains in area through annual removal of existing vegetation. However, persistent vegetation focused flow and thus aggradation over the unvegetated fraction of braidplain, leading to an aggradational imbalance and transition to a more avulsive state. While physical models predict continued narrowing of the active braidplain as T* declines, the future trajectory of channel-vegetation interactions at Pinatubo as sedimentation rates decline appears more complicated due to strong seasonal variability in precipitation and sediment loads. By 2011, seasonal incision in the dry season had started to occur, lowering the water-table, and impeding vegetation growth.

Physical Drivers Vs. Effects of the Wolf-Elk Trophic Cascade on Fluvial Channel Planform, Olympic National Park, Washington

NASA Astrophysics Data System (ADS)

East, A. E.; Jenkins, K. J.; Happe, P. J.; Bountry, J.; Beechie, T. J.; Mastin, M. C.; Sankey, J. B.; Randle, T. J.

2016-12-01

Identifying the relative contributions of physical and ecological processes to channel evolution remains a substantial challenge in fluvial geomorphology. We use a 74-year aerial photographic record of the Hoh, Queets, Quinault, and Elwha Rivers, Olympic National Park, Washington, U.S.A., to investigate whether physical or trophic-cascade-driven ecological factors—excessive elk impacts after wolves were extirpated a century ago—are the dominant controls on channel planform of these gravel-bed rivers. We find that channel width and braiding show strong relationships with recent flood history; all four rivers have widened significantly in recent decades, consistent with increased flood activity since the 1970s. Channel planform also reflects sediment-supply changes, shown, for example, by the response of the Elwha River to a landslide. We surmise that the Hoh River, which shows a multi-decadal trend toward greater braiding, is adjusting to increased sediment supply associated with rapid glacial retreat. These rivers demonstrate rapid transmission of climatic signals through relatively short sediment-routing systems that lack substantial buffering by sediment storage. We infer no correspondence between channel evolution and elk abundance, suggesting that in this system effects of the wolf-driven trophic cascade are subsidiary to physical controls on channel morphology. Our examinations of stage-discharge history, historical maps, photographs, and descriptions, and empirical geomorphic thresholds do not support a previous conceptual model that these rivers underwent a fundamental geomorphic transition (widening, and a shift from single-thread to braided) resulting from large elk populations in the early 20th century. These findings differ from previous interpretations of Olympic National Park river dynamics, and also contrast with previous findings in Yellowstone National Park, where legacy effects of abundant elk nearly a century ago apparently still affect channel and floodplain morphology and connectivity. Different responses of Olympic and Yellowstone river morphology to trophic-cascade factors are likely due to hydrologic regime and large-wood availability.

Ultrasmall multi-channel resonant-tunneling filter using mode gap of width-tuned photonic-crystal waveguide.

PubMed

Shinya, Akihiko; Mitsugi, Satoshi; Kuramochi, Eiichi; Notomi, Masaya

2005-05-30

We have devised an ultra-small multi-channel drop filter based on a two-port resonant tunneling system in a two-dimensional photonic crystal with a triangular air-hole lattice. This filter does not require careful consideration of the interference process to achieve a high dropping efficiency. First we develop three-port systems based on a two-port resonant tunneling filter. Next we devise a multi-port channel drop filter by cascading these three-port systems. In this paper, we demonstrate a ten-channel drop filter with an 18 mum device size by 2D-FDTD calculation, and a three-port resonant tunneling filter with 65+/- 20 % dropping efficiency by experiment.

Laser beat wave resonant terahertz generation in a magnetized plasma channel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhasin, Lalita; Tripathi, V. K.; Kumar, Pawan, E-mail: kumarpawan-30@yahoo.co.in

Resonant excitation of terahertz (THz) radiation by nonlinear mixing of two lasers in a ripple-free self created plasma channel is investigated. The channel has a transverse static magnetic field and supports a THz X-mode with phase velocity close to the speed of light in vacuum when the frequency of the mode is close to plasma frequency on the channel axis and its value decreases with the intensity of lasers. The THz is resonantly driven by the laser beat wave ponderomotive force. The THz amplitude scales almost three half power of the intensity of lasers as the width of the THzmore » eigen mode shrinks with laser intensity.« less

Effects of lateral confinement in natural and leveed reaches of a gravel-bed river: Snake River, Wyoming, USA

USGS Publications Warehouse

Leonard, Christina M.; Legleiter, Carl; Overstreet, Brandon T.

2017-01-01

This study examined the effects of natural and anthropogenic changes in confining margin width by applying remote sensing techniques – fusing LiDAR topography with image-derived bathymetry – over a large spatial extent: 58 km of the Snake River, Wyoming, USA. Fused digital elevation models from 2007 and 2012 were differenced to quantify changes in the volume of stored sediment, develop morphological sediment budgets, and infer spatial gradients in bed material transport. Our study spanned two similar reaches that were subject to different controls on confining margin width: natural terraces versus artificial levees. Channel planform in reaches with similar slope and confining margin width differed depending on whether the margins were natural or anthropogenic. The effects of tributaries also differed between the two reaches. Generally, the natural reach featured greater confining margin widths and was depositional, whereas artificial lateral constriction in the leveed reach produced a sediment budget that was closer to balanced. Although our remote sensing methods provided topographic data over a large area, net volumetric changes were not statistically significant due to the uncertainty associated with bed elevation estimates. We therefore focused on along-channel spatial differences in bed material transport rather than absolute volumes of sediment. To complement indirect estimates of sediment transport derived by morphological sediment budgeting, we collected field data on bed mobility through a tracer study. Surface and subsurface grain size measurements were combined with bed mobility observations to calculate armoring and dimensionless sediment transport ratios, which indicated that sediment supply exceeded transport capacity in the natural reach and vice versa in the leveed reach. We hypothesize that constriction by levees induced an initial phase of incision and bed armoring. Because levees prevented bank erosion, the channel excavated sediment by migrating rapidly across the restricted braidplain and eroding bars and islands. 

Biological, morphological, and chemical characteristics of Wailuku River, Hawaii

USGS Publications Warehouse

Yee, J.J.; Ewart, C.J.

1986-01-01

Biological, morphological, and chemical data on Wailuku River were collected to assess its water quality characteristics. Biological measurements included evaluation of benthic invertebrates, periphyton, phytoplankton and coliform bacteria. Morphological measurements consisted of channel surveys and particle size determination of bed materials. Chemical quality measurements, made monthly at two sampling stations, included water temperature, pH, specific conductance, dissolved solids concentration, turbidity, dissolved oxygen, nitrogen, phosphorus , and minor elements. Biological and chemical data indicated relatively clean water compared to similar streams in conterminous United States. The number and types of benthic organisms are low in Wailuku River. This is due mainly to channel gradient and flow velocities rather than to chemical toxicity. Periphyton data also indicate unpolluted water of low to moderate primary productivity. Diatoms are the dominant organisms observed in the periphyton samples. Coliform bacteria densities are typical of mountain streams in Hawaii that are essentially unaffected by human activities. The streambed is formed of lava flows from Mauna Loa volcano, and the stream channel is characterized by a series of plunge pools and waterfalls. The longitudinal slope ranges from 5% at midreaches to 8% at the headwater regions. There is no broad flood plain at the mouth of the stream. The stream channel is generally a narrow steep-sided trapezoid with an irregular base. Streambanks are composed of fine to very coarse-grained material. Channel depth increases from 6 ft at the headwaters to 40 ft at Hilo. The width also increases from 60 ft at the highest study site to 220 ft at the Hilo site near the mouth of the river. (Author 's abstract)

Large woody debris volumes and accumulation rates in cleaned streams in redwood forest in southern Humboldt County, California

Treesearch

John Wooster; Sue Hilton

2004-01-01

Large woody debris (LWD) was inventoried in 1999 in five streams where LWD was removed in the early 1980s, and no LWD has been artificially introduced since. All study sites are second order channels near the confluence of the South Fork and main-stem Eel River, California. Watershed contributing areas range from 4.7 to 17.4 km², and mean active channel widths...

Distribution of small channels on the Martian surface

NASA Technical Reports Server (NTRS)

Pieri, D.

1976-01-01

The distribution of small channels on Mars has been mapped from Mariner 9 images at the 1:5,000,000 scale. The small channels referred to here are small valleys ranging in width from the resolution limit of the Mariner 9 wide-angle images (about 1 km) to about 10 km. The greatest density of small channels occurs in dark cratered terrain. This dark zone forms a broad subequatorial band around the planet. The observed distribution may be the result of decreased small-channel visibility in bright areas due to obscuration by a high albedo dust or sediment mantle. Crater densities within two small-channel segments show crater size-frequency distributions consistent with those of the oldest of the heavily cratered plains units. Such crater densities coupled with the almost exclusive occurrence of small channels in old cratered terrain and the generally degraded appearance of small channels in the high-resolution images (about 100 m) imply a major episode of small-channel formation early in Martian geologic history.

Evaluating the use of drone photogrammetry for measurement of stream channel morphology and response to high flow events

NASA Astrophysics Data System (ADS)

Price, Katie; Ballow, William

2015-04-01

Traditional high-precision survey methods for stream channel measurement are labor-intensive and require wadeability or boat access to streams. These conditions limit the number of sites researchers are able to study and generally prohibit the possibility of repeat channel surveys to evaluate short-term fluctuations in channel morphology. In recent years, unmanned aerial vehicles (drones) equipped with photo and video capabilities have become widely available and affordable. Concurrently, developments in photogrammetric software offer unprecedented mapping and 3D rendering capabilities of drone-captured photography. In this study, we evaluate the potential use of drone-mounted cameras for detailed stream channel morphometric analysis. We used a relatively low-cost drone (DJI Phantom 2+ Vision) and commercially available, user friendly software (Agisoft Photscan) for photogrammetric analysis of drone-captured stream channel photography. Our test study was conducted on Proctor Creek, a highly responsive urban stream in Atlanta, Georgia, within the crystalline Piedmont region of the southeastern United States. As a baseline, we performed traditional high-precision survey methods to collect morphological measurements (e.g., bankfull and wetted width, bankfull and wetted thalweg depth) at 11 evenly-spaced transects, following USGS protocols along reaches of 20 times average channel width. We additionally used the drone to capture 200+ photos along the same reaches, concurrent with the channel survey. Using the photogrammetry software, we generated georeferenced 3D models of the stream channel, from which morphological measurements were derived from the 11 transects and compared with measurements from the traditional survey method. We additionally explored possibilities for novel morphometric characterization available from the continuous 3D surface, as an improvement on the limited number of detailed cross-sections available from standard methods. These results showed great promise for the drone photogrammetry methods, which encouraged the exploration of the possibility of repeat aerial surveys to evaluate channel response to high flow events. Repeat drone surveys were performed following a sequence of high-flow events in Proctor Creek to evaluate the possibility of using these methods for assessment of stream channel response to flooding.

National Dam Safety Program. Pine Tree Lake East Dam (MO 30992), and Pine Tree Lake West Dam (MO 30995), Mississippi - Kaskaskia - St. Louis Basin, Washington County, Missouri. Phase I Inspection Report.

DTIC Science & Technology

1980-09-01

Spillway. Type Trapezoidal, broad - crested , concrete weir Width 6 ft at bottom, 18 ft at top Crest elevation 994.0 ft Gates None Upstream Channel None... crested concrete weir Length of weir 18 f t (top), 6 f t (bottom) Crest elevation 994 ft Gates None Upstream channel None Downstream channel Earth...instability of the embankment was observed at the time of our inspectici. The slopes and crest of the dam have a thick grass cover with scattered brush and

Assuring the required spectroradiometric characteristics of the Fragment multispectral system

NASA Astrophysics Data System (ADS)

Bogdanov, A. A.; Kuzmin, V. I.; Mosevnina, L. G.; Popkov, A. V.; Sychev, A. G.; Tarnopolskii, V. I.

The paper examines methods and equipment for assuring the required spectroradiometric characteristics of the satellite-borne Fragment multispectral scanning system during development, fabrication, and autonomous and complex testing. These characteristics comprise: (1) the integrated sensitivity of the measuring channels to the spectral density of brightness (SDB): (2) the relative spectral sensitivity of the channels; (3) the effective spectral width of the sensitivity intervals and their position in the spectral range; (4) maximum values of SDB measured by the system in each spectral interval of sensitivity; (5) the SNR in each measuring channel; and (6) the relative rms of SDB measurements.

Experimental investigation and performance analysis of six low flow coefficient centrifugal compressor stages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paroubek, J.; Cyrus, V.; Kyncl, J.

1995-10-01

Some results of a research and development program for centrifugal compressors are presented. Six-stage configurations with low flow coefficient were tested. The stages had channel width parameter b{sub 2}/D{sub 2} = 0.01 and 0.03. For each value of the width parameter, three different impellers with inlet hub to outlet diameter ratio d{sub 0}/D{sub 2} = 0.3, 0.4, and 0.5 were designed. Test rig, instrumentation, and data analysis are described. Special attention was devoted to probe calibrations and to evaluation of the leakage, bearing, and disk friction losses. Aerodynamic performance of all tested stages is presented. Slip factors of impellers obtainedmore » experimentally and theoretically are compared. Losses in both vaneless diffuser and return channel with deswirl vanes are discussed. Rotating stall was also investigated. Criteria for stall limit were tested.« less

Influence of Gate Dielectrics, Electrodes and Channel Width on OFET Characteristics

NASA Astrophysics Data System (ADS)

Liyana, V. P.; Stephania, A. M.; Shiju, K.; Predeep, P.

2015-06-01

Organic Field Effect Transistors (OFET) possess wide applications in large area electronics owing to their attractive features like easy fabrication process, light weight, flexibility, cost effectiveness etc. But instability, high operational voltages and low carrier mobility act as inhibitors to commercialization of OFETs and various approaches were tried on a regular basis so as to make it viable. In this work, Poly 3-hexylthiophene-2,5diyl (P3HT) based OFETs with bottom-contact top-gate configuration using Poly vinyl alcohol (PVA) and Poly (methyl methacrylate) (PMMA) as gate dielectrics, aluminium and copper as source-drain electrodes are investigated. An effort is made to compare the effect of these dielectric materials and electrodes on the performance of OFET. Also, an attempt has been made to optimize the channel width of the device. These devices are characterised with mobility (μ), threshold voltage (VT), on-off ratio (Ion/Ioff) and their comparative analysis is reported.

Timescale bias in measuring river migration rate

NASA Astrophysics Data System (ADS)

Donovan, M.; Belmont, P.; Notebaert, B.

2016-12-01

River channel migration plays an important role in sediment routing, water quality, riverine ecology, and infrastructure risk assessment. Migration rates may change in time and space due to systematic changes in hydrology, sediment supply, vegetation, and/or human land and water management actions. The ability to make detailed measurements of lateral migration over a wide range of temporal and spatial scales has been enhanced from increased availability of historical landscape-scale aerial photography and high-resolution topography (HRT). Despite a surge in the use of historical and contemporary aerial photograph sequences in conjunction with evolving methods to analyze such data for channel change, we found no research considering the biases that may be introduced as a function of the temporal scales of measurement. Unsteady processes (e.g.; sedimentation, channel migration, width changes) exhibit extreme discontinuities over time and space, resulting in distortion when measurements are averaged over longer temporal scales, referred to as `Sadler effects' (Sadler, 1981; Gardner et al., 1987). Using 12 sets of aerial photographs for the Root River (Minnesota), we measure lateral migration over space (110 km) and time (1937-2013) assess whether bias arises from different measurement scales and whether rates shift systematically with increased discharge over time. Results indicate that measurement-scale biases indeed arise from the time elapsed between measurements. We parsed the study reach into three distinct reaches and examine if/how recent increases in river discharge translate into changes in migration rate.

Rapid mixing with high-throughput in a semi-active semi-passive micromixer.

PubMed

Kunti, Golak; Bhattacharya, Anandaroop; Chakraborty, Suman

2017-05-01

In this paper, we investigate a novel alternating current electrothermal (ACET) micromixer driven by a high efficiency ACET micropump. The micromixer consists of thin film asymmetric pairs of electrodes on the microgrooved channel floor and array of electrode pairs fabricated on the top wall. By connecting electrodes with AC voltage, ACET forces are induced. Asymmetric microgrooved electrodes force the fluids along the channel, while lateral vortex pairs are generated by symmetric electrode pairs located on the top wall. Waviness of the floor increases contact area between two confluent streams within a narrow confinement. An active mixer operates as a semi active semi passive mixer. Effects of various parameters are investigated in details in order to arrive at an optimal configuration that provides for efficient mixing as well as appreciable transport. It is found that using a specific design, uniform and homogeneous mixing quality with mixing efficiency of 97.25% and flow rate of 1.794μm2/ min per unit width of the channel can be achieved. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Micro-fabricated packed gas chromatography column based on laser etching technology.

PubMed

Sun, J H; Guan, F Y; Zhu, X F; Ning, Z W; Ma, T J; Liu, J H; Deng, T

2016-01-15

In this work, a micro packed gas chromatograph column integrated with a micro heater was fabricated by using laser etching technology (LET) for analyzing environmental gases. LET is a powerful tool to etch deep well-shaped channels on the glass wafer, and it is the most effective way to increase depth of channels. The fabricated packed GC column with a length of over 1.6m, to our best knowledge, which is the longest so far. In addition, the fabricated column with a rectangular cross section of 1.2mm (depth) × 0.6mm (width) has a large aspect ratio of 2:1. The results show that the fabricated packed column had a large sample capacity, achieved a separation efficiency of about 5800 plates/m and eluted highly symmetrical Gaussian peaks. Copyright © 2015 Elsevier B.V. All rights reserved.

Hydraulic-Geometry Relations for Rivers in Coastal and Central Maine

USGS Publications Warehouse

Dudley, Robert W.

2004-01-01

Hydraulic-geometry relations (curves) were derived for 15 sites on 12 rivers in coastal and central Maine on the basis of site-specific (at-a-station) hydraulic-geometry relations and hydraulic models. At-a-station hydraulic-geometry curves, expressed as well-established power functions, describe the relations between channel geometry, velocity, and flow at a given point on a river. The derived at-a-station hydraulic-geometry curves indicate that, on average, a given increase in flow at a given river cross section in the study area will be nearly equally conveyed by increases in velocity and channel cross-sectional area. Regional curves describing the bankfull streamflow and associated channel geometry as functions of drainage area were derived for use in stream-channel assessment and restoration projects specific to coastal and central Maine. Regional hydraulic-geometry curves were derived by combining hydraulic-geometry information for 15 river cross sections using bankfull flow as the common reference streamflow. The exponents of the derived regional hydraulic-geometry relations indicate that, in the downstream direction, most of the conveyance of increasing contribution of flow is accommodated by an increase in cross-sectional area?with about 50 percent of the increase in flow accommodated by an increase in channel width, and 32 percent by an increase in depth. The remaining 18 percent is accommodated by an increase in streamflow velocity. On an annual-peak-series basis, results of this study indicate that the occurrence of bankfull streamflow for rivers in Maine is more frequent than the 1.5-year streamflow. On a flow-duration basis, bankfull streamflow for rivers in coastal and central Maine is equaled or exceeded approximately 8.1 percent of the time on mean?or about 30 days a year. Bankfull streamflow is roughly three times that of the mean annual streamflow for the sites investigated in this study. Regional climate, snowmelt hydrology, and glacial geology may play important roles in dictating the magnitude and frequency of occurrence of bankfull streamflows observed for rivers in coastal and central Maine.

Rotational Dynamics of the Methyl Radical in Superfluid 4He Nanodroplets

DOE PAGES

Morrison, Alexander M.; Raston, Paul L.; Douberly, Gary E.

2012-12-07

Here, we report the ro-vibrational spectrum of the ν 3(e') band of the methyl radical (CH 3) solvated in superfluid 4He nanodroplets. Five allowed transitions produce population in the N K = 0 0, 1 1, 1 0, 2 2 and 2 0 rotational levels. The observed transitions exhibit variable Lorentzian line shapes, consistent with state specific homogeneous broadening effects. Population relaxation of the 00 and 11 levels is only allowed through vibrationally inelastic decay channels, and the PP 1(1) and RR 0(0) transitions accessing these levels have 4.12(1) and 4.66(1) GHz full-width at half-maximum line widths, respectively. The linemore » widths of the PR 1(1) and RR 1(1) transitions are comparatively broader (8.6(1) and 57.0(6) GHz, respectively), consistent with rotational relaxation of the 2 0 and 2 2 levels within the vibrationally excited manifold. The nuclear spin symmetry allowed rotational relaxation channel for the excited 1 0 level has an energy difference similar to those associated with the 2 0 and 2 2 levels. However, the PQ 1(1) transition that accesses the 1 0 level is 2.3 and 15.1 times narrower than the PR 1(1) and RR 1(1) lines, respectively. The relative line widths of these transitions are rationalized in terms of the anisotropy in the He-CH 3 potential energy surface, which couples the molecule rotation to the collective modes of the droplet.« less

16-channel DWDM based on 1D defect mode nonlinear photonic crystal

NASA Astrophysics Data System (ADS)

Kalhan, Abhishek; Sharma, Sanjeev; Kumar, Arun

2018-05-01

We propose a sixteen-channel Dense Wavelength Division Multiplexer (DWDM), using the 1-D defect mode nonlinear photonic crystal which is a function of intensity as well as wavelength. Here, we consider an alternate layer of two semiconductor materials in which we found the bandgap of materials when defect layer is introduced then 16-channel dense wavelength division multiplexer is obtained within bandgap. From the theoretical analysis, we can achieve average quality factor of 7800.4, the uniform spectral line-width of 0.2 nm, crosstalk of -31.4 dB, central wavelength changes 0.07 nm/(1GW/cm2) and 100% transmission efficiency. Thus, Sixteen-channel DWDM has very high quality factor, low crosstalk, near 100% power transmission efficiency and small channel spacing (1.44 nm).

Hot gas path component having near wall cooling features

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miranda, Carlos Miguel; Kottilingam, Srikanth Chandrudu; Lacy, Benjamin Paul

A method for providing micro-channels in a hot gas path component includes forming a first micro-channel in an exterior surface of a substrate of the hot gas path component. A second micro-channel is formed in the exterior surface of the hot gas path component such that it is separated from the first micro-channel by a surface gap having a first width. The method also includes disposing a braze sheet onto the exterior surface of the hot gas path component such that the braze sheet covers at least of portion of the first and second micro-channels, and heating the braze sheetmore » to bond it to at least a portion of the exterior surface of the hot gas path component.« less

Highly efficient red single transverse mode superluminescent diodes

NASA Astrophysics Data System (ADS)

Andreeva, E. V.; Anikeev, A. S.; Il'chenko, S. N.; Chamorovskii, A. Yu.; Yakubovich, S. D.

2017-12-01

Optimisation of the epitaxial growth of AlGaInP/GaInPAs nanoheterostructures and improvement of the technologies of active channel formation and p-contact deposition made it possible to considerably increase the external differential quantum efficiency (up to 0.5 mW mA-1), the catastrophic optical degradation threshold (up to 40 mW), and the spectral width (to FWHM exceeding 15 nm) of single transverse mode superluminescent diodes with the centre wavelength of about 675 nm. Lifetime tests demonstrated high reliability of these diodes at a cw output optical power up to 30 mW.

Electrical Spin Injection and Detection in Silicon Nanowires with Axial Doping Gradient.

PubMed

Kountouriotis, Konstantinos; Barreda, Jorge L; Keiper, Timothy D; Zhang, Mei; Xiong, Peng

2018-06-19

The interest in spin transport in nanoscopic semiconductor channels is driven by both the inevitable miniaturization of spintronics devices toward nanoscale and the rich spin-dependent physics the quantum confinement engenders. For such studies, the all-important issue of the ferromagnet/semiconductor (FM/SC) interface becomes even more critical at nanoscale. Here we elucidate the effects of the FM/SC interface on electrical spin injection and detection at nanoscale dimensions, utilizing a unique type of Si nanowires (NWs) with an inherent axial doping gradient. Two-terminal and nonlocal four-terminal lateral spin-valve measurements were performed using different combinations from a series of FM contacts positioned along the same NW. The data are analyzed with a general model of spin accumulation in a normal channel under electrical spin injection from a FM, which reveals a distinct correlation of decreasing spin-valve signal with increasing injector junction resistance. The observation is attributed to the diminishing contribution of the d-electrons in the FM to the injected current spin polarization with increasing Schottky barrier width. The results demonstrate that there is a window of interface parameters for optimal spin injection efficiency and current spin polarization, which provides important design guidelines for nanospintronic devices with quasi-one-dimensional semiconductor channels.

Changes to subaqueous delta bathymetry following a high river flow event, Wax Lake Delta, LA, USA

NASA Astrophysics Data System (ADS)

Whaling, A. R.; Shaw, J.

2017-12-01

Sediment transport capacity is increased during high river flow (flood) events which are characterized by discharges that exceed the 15 year median daily statistic. The Wax Lake Delta (WLD) in coastal Louisiana has experienced 19 of these high flow events in the past 20 years, yet the depositional patterns of single floods are rarely measured in a field-scale deltaic setting. We characterize flood deposition and erosion patterns on the subaqueous portion of the WLD by differencing two Digital Elevation Models (DEMs) constructed from bathymetric surveys before and after the third largest flood in the WLD's recorded history. The total suspended sediment discharge for the 496 day inter-survey period was 2.14x107 cubic meters measured 21 km upstream of the delta apex. The difference map showed 1.06x107 cubic meters of sediment was deposited and 8.2x106 cubic meters was eroded, yielding 2.40x106 cubic meters of net deposition in the survey area ( 79.7 km2 ). Therefore the average deposition rate was 0.061 mm/day. Channel planform remained relatively unchanged for five out of six distributary passes however Gadwall Pass experienced a maximum channel displacement of 166 m ( 1 channel width) measured from the thalweg centerline. Channel tip extension was negligible. In addition, channel displacement was not concentrated at any portion along the channel centerline. Maximum erosion occurred within channel margins and increased upstream whereas maximum deposition occurred immediately outside the channel margins. Sediment eroded from the survey area was either subsequently re-deposited or transported out of the system. Our results show that up to 77.4% of deposition in the survey area originated from sediment eroded during the flood. Surprisingly, only 11.2% of the total suspended sediment discharge was retained in the subaqueous portion of the delta after the flood. We conclude that a high flow event does not produce channel progradation. Rather, high flow causes delta aggradation and channel incision. The role of increased sediment supply versus erosive capabilities during high flow is roughly comparable regarding changes to subaqueous delta bathymetry. These counterintuitive results have important implications for land building from sediment diversions and stratigraphic analysis of deltas.

Estimating Discharge in Low-Order Rivers With High-Resolution Aerial Imagery

NASA Astrophysics Data System (ADS)

King, Tyler V.; Neilson, Bethany T.; Rasmussen, Mitchell T.

2018-02-01

Remote sensing of river discharge promises to augment in situ gauging stations, but the majority of research in this field focuses on large rivers (>50 m wide). We present a method for estimating volumetric river discharge in low-order (<50 m wide) rivers from remotely sensed data by coupling high-resolution imagery with one-dimensional hydraulic modeling at so-called virtual gauging stations. These locations were identified as locations where the river contracted under low flows, exposing a substantial portion of the river bed. Topography of the exposed river bed was photogrammetrically extracted from high-resolution aerial imagery while the geometry of the remaining inundated portion of the channel was approximated based on adjacent bank topography and maximum depth assumptions. Full channel bathymetry was used to create hydraulic models that encompassed virtual gauging stations. Discharge for each aerial survey was estimated with the hydraulic model by matching modeled and remotely sensed wetted widths. Based on these results, synthetic width-discharge rating curves were produced for each virtual gauging station. In situ observations were used to determine the accuracy of wetted widths extracted from imagery (mean error 0.36 m), extracted bathymetry (mean vertical RMSE 0.23 m), and discharge (mean percent error 7% with a standard deviation of 6%). Sensitivity analyses were conducted to determine the influence of inundated channel bathymetry and roughness parameters on estimated discharge. Comparison of synthetic rating curves produced through sensitivity analyses show that reasonable ranges of parameter values result in mean percent errors in predicted discharges of 12%-27%.

Natural and anthropogenic change in the morphology and connectivity of tidal channels of southwest Bangladesh

NASA Astrophysics Data System (ADS)

Wilson, C.; Goodbred, S. L., Jr.; Wallace Auerbach, L.; Ahmed, K. R.; Small, C.; Sams, S. E.

2014-12-01

Over the last century, land use changes in the Ganges-Brahmaputra tidal delta have transformed >5000 km2 of intertidal mangrove forest to densely inhabited, agricultural islands that have been embanked to protect against tides and storm surges (i.e., polders). More recently, the conversion of rice paddies to profitable shrimp aquaculture has become increasingly widespread. Recent field studies documented that poldering in southwest Bangladesh has resulted in an elevation deficit relative to that of the natural mangrove forests and mean high water (MHW). The offset is a function of lost sedimentation, enhanced compaction, and an effective rise in MHW from tidal amplification. The morphologic adjustment of the tidal channel network to these perturbations, however, has gone largely undocumented. One effect has been the shoaling of many channels due to decreases in fluvial discharge and tidal prism. We document a previously unrecognized anthropogenic component: the widespread closure of large conduit tidal channels for land reclamation and shrimp farming. GIS analysis of historical Landsat and Google Earth imagery within six 1000 km2 study areas reveals that the tidal network in the natural Sundarbans mangrove forest has remained relatively constant since the 1970s, while significant changes are observed in human-modified areas. Construction of the original embankments removed >1000 km of primary tidal creeks, and >80 km2 of land has been reclaimed outside of polders through the closure of formerly active tidal channels (decrease in mean channel width from 256±91 m to 25±10 m). Tidal restriction by large sluice gates is prevalent, favoring local channel siltation. Furthermore, severing the intertidal platform and large conduit channels from the tidal network has had serious repercussions, such as increased lateral migration and straightening of the remaining channels. Where banklines have eroded, the adjacent embankments appear to be more vulnerable to failure, as observed from the effects of Cyclone Aila in 2009: multiple embankments failed at sites of recent channel migration and impounded primary creeks. Although global climate change and sea-level rise is a major concern for this low-lying delta, this study highlights the need to understand the repercussions of anthropogenic modification as well.

Near-barrier Fusion Evaporation and Fission of 28Si+174Yb and 32S+170Er

NASA Astrophysics Data System (ADS)

Wang, Dongxi; Lin, Chengjian; Jia, Huiming; Ma, Nanru; Sun, Lijie; Xu, Xinxing; Yang, Lei; Yang, Feng; Zhang, Huanqiao; Bao, Pengfei

2017-11-01

Fusion evaporation residues and fission fragments have been measured, respectively, at energies around the Coulomb barrier for the 28Si+174Yb and 32S+170Er systems forming the same compound nucleus 202Po. The excitation function of fusion evaporation, fission as well as capture reactions were deduced. Coupled-channels analyses reveal that couplings to the deformations of targets and the two-phonon states of projectiles contribute much to the enhancement of capture cross sections at sub-barrier energies. The mass and total kinetic energy of fission fragments were deduced by the time-difference method assuming full momentum transfer in a two-body kinematics. The mass-energy and mass-angle distributions were obtained and no obvious quasi-fission components were observed in this bombarding energy range. Further, mass distributions of fission fragments were fitted to extract their widths. Results show that the mass widths decrease monotonically with decreasing energy, but might start to increase when Ec.m./VB < 0.95 for both systems.

Bubble propagation on a rail: a concept for sorting bubbles by size

NASA Astrophysics Data System (ADS)

Franco-Gómez, Andrés; Thompson, Alice B.; Hazel, Andrew L.; Juel, Anne

We demonstrate experimentally that the introduction of a rail, a small height constriction, within the cross-section of a rectangular channel could be used as a robust passive sorting device in two-phase fluid flows. Single air bubbles carried within silicone oil are generally transported on one side of the rail. However, for flow rates marginally larger than a critical value, a narrow band of bubble sizes can propagate (stably) over the rail, while bubbles of other sizes segregate to the side of the rail. The width of this band of bubble sizes increases with flow rate and the size of the most stable bubble can be tuned by varying the rail width. We present a complementary theoretical analysis based on a depth-averaged theory, which is in qualitative agreement with the experiments. The theoretical study reveals that the mechanism relies on a non-trivial interaction between capillary and viscous forces that is fully dynamic, rather than being a simple modification of capillary static solutions.

The influence of flood frequency, riparian vegetation and threshold on long-term river transport capacity

NASA Astrophysics Data System (ADS)

Croissant, Thomas; Lague, Dimitri; Davy, Philippe

2016-04-01

Climate fluctuations at geological timescales control the capacity of rivers to transport sediment with consequences on geochemical cycles, sedimentary basins dynamics and sedimentation/tectonics interactions. While the impact of differential friction generated by riparian vegetation has been studied for individual flood events, its impact on the long-term sediment transport capacity of rivers, modulated by the frequency of floods remains unknown. Here, we investigate this effect on a simplified river-floodplain configuration obeying observed hydraulic scaling laws. We numerically integrate the full-frequency magnitude distribution of discharge events and its impact on the transport capacity of bedload and suspended material for various level of vegetation-linked differential friction. We demonstrate that riparian vegetation by acting as a virtual confinement of the flow i) increases significantly the instantaneous transport capacity of the river independently of the transport mode and ii) increases the long term bedload transport rates as a function of discharge variability. Our results expose the dominance of flood frequency rather than riparian vegetation on the long term sediment transport capacity. Therefore, flood frequency has to be considered when evaluating long-term bedload transport capacity while floodplain vegetation is important only in high discharge variability regimes. By comparing the transport capacity of unconfined alluvial rivers and confined bedrock gorges, we demonstrate that the latter always presents the highest long term transport capacity at equivalent width and slope. The loss of confinement at the transition between bedrock and alluvial river must be compensated by a widening or a steepening of the alluvial channel to avoid infinite storage. Because steepening is never observed in natural system, we compute the alluvial widening factor value that varies between 3 to 11 times the width of the bedrock channel depending on riparian vegetation and discharge variability. This result is well supported by measurements made in natural river systems in different worldwide locations (Taiwan, Himalayas and New Zealand). Although bank cohesion is often invoked to as a property that sets alluvial river width, we propose unconfinement as another important control factor.

Exploring Controls on Sinuousity, Terraces and River Capture in the Upper Dajia River, Taiwan

NASA Astrophysics Data System (ADS)

Belliveau, L. C.; Ouimet, W. B.; Chan, Y. C.; Byrne, T. B.

2015-12-01

Taiwan is one of the most tectonically active regions in the world and is prone to landslides due to steep topography, large earthquakes and frequent typhoons. Landslides often affect and alter the river valleys beneath them, producing knickpoints on longitudinal river profiles, segmenting valleys into mixed bedrock-alluvial rivers and affecting river incision for tens to thousands of years. This study investigates the origin and evolution of complex channel morphologies, terraces and river capture along a 20km stretch of the Upper Da-Jia River in the Heping area of Taiwan. Through GIS analysis and field studies, we explore controls on river channel sinuousity, terrace development and river capture in relation to tectonic and climatic forcing, rock erodibility and landslides. High channel sinuousity is proposed as the result of a coupling between bank erosion and landslides. We discuss three types of landslide-induced meanders and increased sinuousity: (a) depositional-push meanders, (b) failure-zone erosional meanders, and (c) complex-erosional meanders. We also investigate spatial variation in channel morphology (slope, width) and the distribution and heights of river terraces within the Upper Da-Jia watershed associated with periods of widespread valley filling from landslide activity. Examples of river capture provide further evidence of the dynamic interactions between river incision, landslides and associated changes in channel morphology and terrace development within steep rapidly uplift, eroding and evolving mountain belts.

Distribution of small channels on the Martian surface

USGS Publications Warehouse

Pieri, D.

1976-01-01

The distribution of small channels on Mars has been mapped from Mariner 9 images, at the 1:5 000 000 scale, by the author. The small channels referred to here are small valleys ranging in width from the resolution limit of the Mariner 9 wide-angle images (???1 km) to about 10 km. The greatest density of small band occurs in dark cratered terrain. This dark zone forms a broad subequatorial band around the planet. The observed distribution may be the result of decreased small-channel visibility in bright areas due to obscuration by a high albedo dust or sediment mantle. Crater densities within two small-channel segments show crater size-frequency distributions consistent with those of the oldest of the heavily cratered plains units. Such crater densities coupled with the almost exclusive occurrence of small channels in old cratered terrain and the generally degraded appearance of small channels in the high-resolution images (???100 m) imply a major episode of small-channel formation early in Martian geologic history. ?? 1976.

The case of the shrinking channels; the North Platte and Platte rivers in Nebraska

USGS Publications Warehouse

Williams, Garnett P.

1978-01-01

Since the latter part of the 19th century, channels of North Platte and Platte Rivers in western and central Nebraska have changed considerably. In the 365-km reach from Minatare to Overton, the channel by 2969 ws only about 0.1-0.2 as wide in 1865. The 1969 channel for this reach was less braided and slightly more sinuous than the 1938 channel. (No data are available for braiding and sinuosity prior to 1938.) From Overton to lGrand Island the 1969 channel was about o.6-0.7 as wide as in 1865, and various changes in braiding and sinuosity took place between 1938 and 1969. The decreases in channel width are related to decreases in water discharge. Such flow reductions have resulted primarily from regulating effects of major upstream dams and greater use of the river water. Much of the former river channel is now overgrown with vegetation. (Woodard-USGS)

Electrical guidance efficiency of downstream-migrating juvenile Sea Lamprey decreases with increasing water velocity

USGS Publications Warehouse

Miehls, Scott M.; Johnson, Nicholas; Haro, Alexander

2017-01-01

We tested the efficacy of a vertically oriented field of pulsed direct current (VEPDC) created by an array of vertical electrodes for guiding downstream-moving juvenile Sea Lampreys Petromyzon marinus to a bypass channel in an artificial flume at water velocities of 10–50 cm/s. Sea Lampreys were more likely to be captured in the bypass channel than in other sections of the flume regardless of electric field status (on or off) or water velocity. Additionally, Sea Lampreys were more likely to be captured in the bypass channel when the VEPDC was active; however, an interaction between the effects of VEPDC and water velocity was observed, as the likelihood of capture decreased with increases in water velocity. The distribution of Sea Lampreys shifted from right to left across the width of the flume toward the bypass channel when the VEPDC was active at water velocities less than 25 cm/s. The VEPDC appeared to have no effect on Sea Lamprey distribution in the flume at water velocities greater than 25 cm/s. We also conducted separate tests to determine the threshold at which Sea Lampreys would become paralyzed. Individuals were paralyzed at a mean power density of 37.0 µW/cm3. Future research should investigate the ability of juvenile Sea Lampreys to detect electric fields and their specific behavioral responses to electric field characteristics so as to optimize the use of this technology as a nonphysical guidance tool across variable water velocities.

Scaling relations for large Martian valleys

NASA Astrophysics Data System (ADS)

Som, Sanjoy M.; Montgomery, David R.; Greenberg, Harvey M.

2009-02-01

The dendritic morphology of Martian valley networks, particularly in the Noachian highlands, has long been argued to imply a warmer, wetter early Martian climate, but the character and extent of this period remains controversial. We analyzed scaling relations for the 10 large valley systems incised in terrain of various ages, resolvable using the Mars Orbiter Laser Altimeter (MOLA) and the Thermal Emission Imaging System (THEMIS). Four of the valleys originate in point sources with negligible contributions from tributaries, three are very poorly dissected with a few large tributaries separated by long uninterrupted trunks, and three exhibit the dendritic, branching morphology typical of terrestrial channel networks. We generated width-area and slope-area relationships for each because these relations are identified as either theoretically predicted or robust terrestrial empiricisms for graded precipitation-fed, perennial channels. We also generated distance-area relationships (Hack's law) because they similarly represent robust characteristics of terrestrial channels (whether perennial or ephemeral). We find that the studied Martian valleys, even the dendritic ones, do not satisfy those empiricisms. On Mars, the width-area scaling exponent b of -0.7-4.7 contrasts with values of 0.3-0.6 typical of terrestrial channels; the slope-area scaling exponent $\\theta$ ranges from -25.6-5.5, whereas values of 0.3-0.5 are typical on Earth; the length-area, or Hack's exponent n ranges from 0.47 to 19.2, while values of 0.5-0.6 are found on Earth. None of the valleys analyzed satisfy all three relations typical of terrestrial perennial channels. As such, our analysis supports the hypotheses that ephemeral and/or immature channel morphologies provide the closest terrestrial analogs to the dendritic networks on Mars, and point source discharges provide terrestrial analogs best suited to describe the other large Martian valleys.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rist, J.; Miteva, T.; Gaire, B.

In this paper we present a comprehensive and detailed study of Interatomic Coulombic Decay (ICD) occurring after irradiating argon dimers with XUV-synchrotron radiation. A manifold of different decay channels is observed and the corresponding initial and final states are assigned. Additionally, the effect of nuclear dynamics on the ICD electron spectrum is examined for one specific decay channel. The internuclear distance-dependent width Γ(R) of the decay is obtained from the measured kinetic energy release distribution of the ions employing a classical nuclear dynamics model.

Derivation and Application of Idealized Flow Conditions in River Network Simulation

NASA Astrophysics Data System (ADS)

Afshari Tork, S.; Fekete, B. M.

2015-12-01

Stream flow information is essential for many applications across broad range of scales, e.g. global water balances, engineering design, flood forecasting, environmental management, etc. Quantitative assessment of flow dynamics of natural streams, requires detailed knowledge of all the geometrical and geophysical variables (e.g. bed-slope, bed roughness, etc.) along river reaches. Simplifying the river bed geometries could reduce both the computational burden implementing flow simulations and challenges in assembling the required data, especially for large domains. Average flow conditions expressed as empirical "at-a-station" hydraulic geometry relationships between key channel components, (i.e. water depth, top-width, flow velocity, flow area against discharge) have been studied since 60's. Recent works demonstrated that power-function as idealized riverbed geometry whose parameters are correlated to those of exponential relationship between mean water depth and top-width, are consistent with empirical "at-a-station" relations.US Geological Surveys' National Water Information System web-interface provides huge amount of river discharge and corresponding stage height data from several thousands of streamflow monitoring stations over United States accompanied by river survey summaries providing additional flow informations (width, mean velocity, cross-sectional area). We conducted a series of analyses to indentify consistent data daily monitoring and corresponding survey records that are suitable to refine our current understanding of how the "at-a-station" properties of river channels relate to channel forming characteristics (e.g. riverbed slope, flow regime, geology, etc.). The resulting ~1,200 actively operating USGS stations with over ~225,000 corresponding survery records (almost 200 survey per gauge on average) is the largest river survey database ever studied in the past.Our presentation will show our process assembling our river monitoring and survey data base and we will present our first results translating "at-a-station" relations into he hydraulic geometry of river channels based on idealized power-law riverbed geometries. We also will also present a series of application (e.g. improved flow rounting, simplyfied river surveying).

Influence of riparian vegetation on channel widening and subsequent contraction on a sand-bed stream since European settlement: Widden Brook, Australia

NASA Astrophysics Data System (ADS)

Erskine, Wayne; Keene, Annabelle; Bush, Richard; Cheetham, Michael; Chalmers, Anita

2012-04-01

Widden Brook in the Hunter Valley, Australia, was first settled by Europeans in 1831 and had widened substantially by the 1870s due to frequent floods during a flood-dominated regime impacting on highly disturbed banks whose riparian trees had been either ringbarked or cleared, and whose understorey had been grazed. Catastrophic floods in 1950 (many), two in August 1952 and one in February 1955 effected the final phase of channel widening at the onset of a second flood-dominated regime more than half a century after the initial widening. Contraction has been active since 1963 by a combination of five biogeomorphic processes. Firstly, rapid channel widening, migration and cutoffs totally reworked the pre-European floodplain and were followed by active floodplain formation. Initial bar formation was replaced by sand splay and overbank deposition which constructed a new floodplain and narrower channel. Secondly, overwidened channel segments that were produced by the catastrophic 1955 flood have contracted since 1963 by the formation of up to four bank-attached, discontinuous benches below the floodplain. Each bench has a bar nucleus of pebbly coarse sand overlain by stratified fine-medium sand and mud. Colonisation by River Sheoaks (Casuarina cunninghamiana subsp. cunninghamiana) or grasses (Cynodon dactylon, Paspalum distichum, Pennisetum clandestinum) is important in converting bars to benches. Thirdly, narrower segments which developed since 1963 have contracted by small-scale accretion on both banks. These deposits are steeply dipping, interbedded sand and mud trapped by stoloniferous and rhizomatous grasses (C. dactylon, P. distichum, P. clandestinum) which also rapidly stabilise the deposits. Fourthly, rare laterally migrating, small radius bends have contracted by recent point bar formation greatly exceeding cutbank recession rates. Point bar formation is controlled by secondary currents producing inclined stratified coarse sands without the influence of vegetation. Lastly, rare, overwidened, non-migrating, large radius bends have greatly contracted by the infilling of dissecting chutes across the convex bank. Establishment of stoloniferous and rhizomatous clonal grasses (Phragmites australis, C. dactylon, P. distichum, P. clandestinum) is important in inducing sedimentation of the chutes. Contraction has produced a much narrower channel than the design width between river training fences which were installed progressively between the 1960s and 1990s. The recent flood history of Widden Brook has not included any catastrophic floods of a size similar to February 1955. Our work demonstrates that both trees and grasses can be associated with narrower channel widths and that the causal link between width and vegetation type is more complex than usually acknowledged.

Potential flood hazards and hydraulic characteristics of distributary-flow areas in Maricopa County, Arizona

USGS Publications Warehouse

Hjalmarson, H.W.

1994-01-01

Flood hazards of distributary-flow areas in Maricopa County, Arizona, can be distinguished on the basis of morphological features. Five distributary-flow areas represent the range of flood-hazard degree in the study area. Descriptive factors, including the presence of desert varnish and the absence of saguaro cactus, are more useful than traditional hydraulic-based methods in defining hazards. The width, depth, and velocity exponents of the hydraulic-geometry relations at the primary diffluences of the sites are similar to theoretical exponents for streams with cohesive bank material and the average exponents of stream channels in other areas in the United States. Because of the unexplained scatter of the values of the exponent of channel width, however, the use of average hydraulic-geometry relations is con- sidered inappropriate for characterizing flood hazards for specific distributary-flow in Maricopa County. No evidence has been found that supports the use of stochastic modeling of flows or flood hazards of many distributary-flow areas. The surface of many distributary-flow areas is stable with many distributary channels eroded in the calcreted surface material. Many distributary- flow areas do not appear to be actively aggrading today, and the paths of flow are not changing.

Adaptive beam-width control of echolocation sounds by CF-FM bats, Rhinolophus ferrumequinum nippon, during prey-capture flight.

PubMed

Matsuta, Naohiro; Hiryu, Shizuko; Fujioka, Emyo; Yamada, Yasufumi; Riquimaroux, Hiroshi; Watanabe, Yoshiaki

2013-04-01

The echolocation sounds of Japanese CF-FM bats (Rhinolophus ferrumequinum nippon) were measured while the bats pursued a moth (Goniocraspidum pryeri) in a flight chamber. Using a 31-channel microphone array system, we investigated how CF-FM bats adjust pulse direction and beam width according to prey position. During the search and approach phases, the horizontal and vertical beam widths were ±22±5 and ±13±5 deg, respectively. When bats entered the terminal phase approximately 1 m from a moth, distinctive evasive flight by G. pryeri was sometimes observed. Simultaneously, the bats broadened the beam widths of some emissions in both the horizontal (44% of emitted echolocation pulses) and vertical planes (71%). The expanded beam widths were ±36±7 deg (horizontal) and ±30±9 deg (vertical). When moths began evasive flight, the tracking accuracy decreased compared with that during the approach phase. However, in 97% of emissions during the terminal phase, the beam width was wider than the misalignment (the angular difference between the pulse and target directions). These findings indicate that bats actively adjust their beam width to retain the moving target within a spatial echolocation window during the final capture stages.

Occurrence of riverine wetlands on floodplains along a climatic gradient

USGS Publications Warehouse

Kroes, D.E.; Brinson, M.M.

2004-01-01

The relation between the occurrence of riverine wetlands in floodplains along a humid to semi-arid climatic continuum was studied in two regions. The first included 36 mid-reach streams from Colorado to Iowa, USA, a region with a broad range of PET ratios (potential evapotranspiration/precipitation) from 0.70 to 1.75. The second region included 16 headwater streams in eastern North Carolina with PET ratios ranging from 0.67 to 0.83. Wetland boundaries were identified in the field along transects perpendicular to the floodplain. The width of jurisdictional wetlands was compared with flood-prone width (FPW) and expressed as a percent. An increase in PET ratio corresponded to an exponential decrease in the percentage of the FPW that is wetland. Soil texture, duration of overbank flow, and stream order did not correlate with percentage of FPW that was wetland. Streams with a PET ratio greater than 0.98 did not have wetlands associated with them. Greater channel cross-sectional areas correlated positively with greater wetland widths in both study regions. Overbank flow did not appear to contribute to wetland prevalence. Supplemental ground-water sources, however, as indicated by greater base flows, could not be ruled out as sources contributing to wetland occurrence. ?? 2004, The Society of Wetland Scientists.

FIBER AND INTEGRATED OPTICS: Analysis of the characteristics of a radio signal at the output of a multimode interference-type fiber channel

NASA Astrophysics Data System (ADS)

Bratchikov, A. N.; Glukhov, I. P.

1992-02-01

An analysis is made of a theoretical model of an interference fiber channel for transmission of microwave signals. It is assumed that the channel consists of a multimode fiber waveguide with a step or graded refractive-index profile. A typical statistic of a longitudinal distribution of inhomogeneities is also assumed. Calculations are reported of the interference losses, the spectral profile of the output radio signal, the signal/noise ratio in the channel, and of the dependences of these parameters on: the type, diameter, and the length of the multimode fiber waveguide; the spectral width of the radiation source; the frequency offset between the interfering optical signals.

Remote Sensing of Water Vapor and Thin Cirrus Clouds using MODIS Near-IR Channels

NASA Technical Reports Server (NTRS)

Gao, Bo-Cai; Kaufman, Yoram J.

2001-01-01

The Moderate Resolution Imaging Spectroradiometer (MODIS), a major facility instrument on board the Terra Spacecraft, was successfully launched into space in December of 1999. MODIS has several near-IR channels within and around the 0.94 micrometer water vapor bands for remote sensing of integrated atmospheric water vapor over land and above clouds. MODIS also has a special near-IR channel centered at 1.375-micron with a width of 30 nm for remote sensing of cirrus clouds. In this paper, we describe briefly the physical principles on remote sensing of water vapor and cirrus clouds using these channels. We also present sample water vapor images and cirrus cloud images obtained from MODIS data.

Effects of geometric configuration on droplet generation in Y-junctions and anti-Y-junctions microchannels

NASA Astrophysics Data System (ADS)

Liu, Zhao-Miao; Liu, Li-Kun; Shen, Feng

2015-10-01

Droplets generation in Y-junctions and anti-Y-junctions microchannels are experimentally studied using a high speed digital microscopic system and numerical simulation. Geometric configuration of a microchannel, such as Y-angle (90°, 135°, -90° and -135°), channel depth and other factors have been taken into consideration. It is found that droplets generated in anti-Y-junctions have a smaller size and a shorter generation cycle compared with those in Y-junctions under the same experimental conditions. Through observing the internal velocity field, the vortex appearing in continuous phase in anti-Y-junctions is one of the key factors for the difference of droplet size and generation cycle. It is found that droplet size is bigger and generation cycle is longer when the absolute angle value of the intersection between the continuous and the dispersed phases (i.e., the angle between the main channel and the continuous phase or the dispersed phase channel) increases. The droplet's size is influenced by the Y-angle, which varies with the channel depth in Y-junctions. The Y-angle has a positive effect on the droplet generation cycle, but a smaller height-width ratio will enhance the impact of a continuous and dispersed phase's intersection angle on the droplet generation cycle in Y-junctions microchannels.

A microfabricated hybrid device for DNA sequencing.

PubMed

Liu, Shaorong

2003-11-01

We have created a hybrid device of a microfabricated round-channel twin-T injector incorporated with a separation capillary in order to extend the straight separation distance for high speed and long readlength DNA sequencing. Semicircular grooves on glass wafers are obtained using a photomask with a narrow line-width and a standard isotropic photolithographic etching process. Round channels are made when two etched wafers are face-to-face aligned and bonded. A two-mask fabrication process has been developed to make channels of two different diameters. The twin-T injector is formed by the smaller channels whose diameter matches the bore of the separation capillary, and the "usual" separation channel, now called the connection channel, is formed by the larger ones whose diameter matches the outer diameter of the separation capillary. The separation capillary is inserted through the connection channel all the way to the twin-T injector to allow the capillary bore flush with the twin-T injector channels. The total dead-volume of the connection is estimated to be approximately 5 pL. To demonstrate the efficiency of this hybrid device, we have performed four-color DNA sequencing on it. Using a 200 microm twin-T injector coupled with a separation capillary of 20 cm effective separation distance, we have obtained readlengths of 800 plus bases at an accuracy of 98.5% in 56 min, compared to about 650 bases in 100 min on a conventional 40 cm long capillary sequencing machine under similar conditions. At an increased separation field strength and using a diluted sieving matrix, the separation time has been reduced to 20 min with a readlength of 700 bases at 98.5% base-calling accuracy.

Respones of sandhill crane (Grus canadensis) riverine roosting habitat to changes in stage and sandbar morphology

USGS Publications Warehouse

Kinzel, P.J.; Nelson, J.M.; Heckman, A.K.

2009-01-01

Over the past century, flow regulation and vegetation encroachment have reduced active channel widths along the central Platte River, Nebraska. During the last two decades, an annual program of in-channel vegetation management has been implemented to stabilize or expand active channel widths. Vegetation management practices are intended to enhance riverine habitats which include nocturnal roosting habitat for sandhill cranes. Evaluating the success of other management treatments such as streamflow modification requires an understanding of how flow shapes the sandbars in the river and how sandbar morphology interacts with flow to create crane habitat. These linkages were investigated along a 1-km managed river reach by comparing the spatial pattern of riverine roosts and emergent sandbars identified with aerial infrared imagery to variables computed with a two-dimensional hydraulic model. Nocturnal observations made multiple years showed that the area and patterns of riverine roosts and emergent sandbars and the densities of cranes within roosts changed with stage. Despite sandbar vegetation management, low flows were concentrated into incised channels rather than spread out over broad sandbars. The flow model was used to compute hydraulic variables for identical streamflows through two sandbar morphologies; one following a period of relatively high flow and the other following the low-flow period. Compared with the simulation using the morphology from the antecedent high flow, the simulation using the morphology from the antecedent low flow produced a smaller quantity of available wetted area. These remote-sensing observations and hydraulic simulations illustrate the importance of considering flow history when designing streamflows to manage in-channel habitat for cranes.

Seismic geomorphology of the Lobed-channel System of Upper Miocene Huangliu Formation, Yinggehai Basin, Northwestern South China Sea

NASA Astrophysics Data System (ADS)

Liu, H.

2016-02-01

Three-dimensional seismic data have been widely used in interpreting ancient river systems and their associated sediment deposits. Thin-bed reservoirs of lobed-channel system in lithostratigraphic units of Dongfang (DF) area are one of the major study areas for reservoir growth in the Yinggehai basin of northwestern South China Sea. Although it is understood that the transport mechanics of parent substrate and alluvium determine the morphology of channel for lobed-channel system, the transport mechanism and regional gradient are relatively poorly understood. This study is focused on the application of various techniques in seismic geomorphology to the Yinggehai Basin at paleo-water-depth of 120m to assess influences of regional gradient and relative sea level change on lobed-channel palaeogeomorphology in shallow-water environments. The Vietnam paleo-Blue River, which located at south of modern Red River, flowed through DF area and transported turbidity deposit to DF area in the coastal environment. In 3-D seismic survey area, four fifth-order sequences in first member of upper Miocene Huangliu formation were identified using well and seismic data. Seismic inversion and 90° phasing of seismic data were used to convert seismic traces to pseudolithologic logs. Stratal slicing made it possible to interpolate and extrapolate well-data-derived sequence and identify submarine fan, channel fill, lobes and overbank deposit. Strata slices suggested that sea-floor slopes exerted main influence on channel morphology. Specifically, DF13-1 block had high gradient, which mainly distributed mud-sand-rich lobes. However, DF13-2 block established low gradient, which mostly indicated sand-rich braided channels. The values of sinuosity, channel widths, meander-belt widths in DF13-2 block are all greater than these in DF13-1 block. In addition, results of carbon isotope measurements and foraminiferal research of two blocks suggest that paleo sea level in DF13-2 block (30m 150m) was higher than that of DF13-1 block (20m 90m). It also deciphered why channels in DF13-2 incised deeply because of the stronger hydrodynamic energy in the shallow-water environments. Thus DF13-2 block was formed in a lobed-channel and sand rich system, compared with DF13-1 of channelized-lobes and mud-sand rich system.

Central tracker for BM@N experiment based on double side Si-microstrip detectors

NASA Astrophysics Data System (ADS)

Kovalev, Yu.; Kapishin, M.; Khabarov, S.; Shafronovskaia, A.; Tarasov, O.; Makankin, A.; Zamiatin, N.; Zubarev, E.

2017-07-01

Design of central tracker system based on Double-Sided Silicon Detectors (DSSD) for BM@N experiment is described. A coordinate plane with 10240 measuring channels, pitch adapter, reading electronics was developed. Each element was tested and assembled into a coordinate plane. The first tests of the plane with 106Ru source were carried out before installation for the BM@N experiment. The results of the study indicate that noisy channels and inefficient channels are less than 3%. In general, single clusters 87% (one group per module of consecutive strips) and 75% of clusters with a width equal to one strip.

Bedload and river hydraulics - Inferences from the East Fork River, Wyoming

USGS Publications Warehouse

Leopold, Luna Bergere; Emmett, William W.

1997-01-01

During 1973-79, bedload data were collected in a sophisticated trap on a river of moderate size, the East Fork. The transport rate was measured most days through a full snowmelt season, and the rate was determined separately for eight zones across the channel width. The quantitative data are unique and unlikely to be repeated. Nor need they be, because as a result of this effort a practical bedload sampler was adequately tested against full river measurement.It was shown that bedload moves sporadically and randomly on the river bed. Therefore, transport rate is highly variable in short periods of time. There is also a wide variance from day to day. Yet, different rivers have transport rates, which are functions of discharge, depth, and sediment size, that are clearly distinct. Comparison of computed and measured transport rates indicates that a major problem remains: What grain size is representative of the bedload when there is a wide or heterogeneous particle-size distribution? Size of the bedload in motion may be very different from the size of bed material obtained from samples of the streambed.For general computation, the river channel slope may be averaged, and it may be assumed that water-surface slope does not change materially with changing discharge. Indeed, this generality is correct, in that, compared with depth, velocity, and width, slope is conservative at-a-station. However, in more detail, slope changes importantly with discharge in short reaches of channel, and those changes are very different in pool and riffle.These local changes in slope are not merely an aspect of a detailed longitudinal profile but involve cross-channel as well as down-channel components. The pool and riffle sequence involves not only undulation of bed elevation and bar formation on alternate sides of the channel, but alternation of the zone of superovulation of the water surface, and changing relation of watersurface slope to discharge. These details can be seen only in the full topography of the water surface. Riffles fill during high flow and scour at low flow. Changes in local water-surface slope illustrate this process. Pools are a storage zone for sediment in the low-flow season. Even though large volumes of sediment move, the distance moved is not large—in the East Fork River, sand of size 0.5-1 millimeter moved 650 meters during the 1979 snowmelt runoff season.Bedload transport is greatest over or near bars and not in the deepest part of the channel. Direct observation of the locus of sediment transport indicates that this locus moves from one side of the channel to the other in concert with the occurrence of alternate bars. Separately, data indicate that at constant stream power, transport rate increases as depth decreases.

Riparian Vegetation Effects on Near-Bank Turbulence During Overbank Flows: A Flume Experiment

NASA Astrophysics Data System (ADS)

McBride, M.; Thompson, D. M.; Owen, T. E.; Pearce, A. R.; Hession, W. C.; Rizzo, D.

2005-12-01

Measurements from a fixed-bed, Froude-scaled hydraulic model of a stream in northeastern Vermont demonstrated the importance of riparian vegetation effects on near-bank turbulence during overbank flood events. The prototype stream, a tributary to Sleepers River, increased in channel width within the last 40 years in response to passive reforestation of its riparian zone. Previous research has found that reaches of small streams with forested riparian zones are commonly wider that adjacent reaches with non-forested, or meadow, vegetation; however, the driving mechanisms for this morphologic difference are not fully explained. Flume experiments were performed to investigate near-bank turbulence as a mechanism for channel widening in response to reforestation. A 1:5 scale, simplified model of half a channel and its adjacent floodplain was constructed within a 6 m long recirculating flume. The test region was 3.7 m long and 0.9 m wide and oriented with the channel centerline at the flume wall. The channel bed slope was fixed at 0.03, and experiments were run at three discharges: 30, 33, and 36 l/s. Two types of riparian vegetation scenarios were simulated: forested, with rigid, randomly-distributed, wooden dowels, and non-forested, with synthetic grass carpeting. Three-dimensional velocities were measured with a Nortek Vectrino acoustic Doppler velocimeter at 41 different locations within the channel and floodplain at near-bed and 0.6-depth elevations. Observations of three-dimensional velocities and calculations of turbulent kinetic energy (TKE) showed significant differences between forested and non-forested runs. Results indicated that turbulence intensity, as quantified by TKE, roughly doubled throughout the channel and floodplain when forested vegetation was introduced. Given that sediment entrainment and transport can be amplified in flows with high turbulence intensity, our results demonstrated the potential for increased erosion during overbank flood events in stream reaches with recently reforested riparian zones. The concentration of high TKE values and vertical upwelling at the channel-floodplain interface in forested runs indicated a probable erosion hot spot that could promote channel widening.

Self-healing patterns in ferromagnetic-superconducting hybrids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vlasko-Vlasov, V. K.; Palacious, E.; Rosenmann, D.

We study magnetic flux dynamic effects in a superconducting bridge with thin soft magnetic stripes placed either on top or under the bridge. Voltage-current (VI) measurements reveal that the edges of magnetic stripes oriented transvers or along the bridge introduce channels or barriers for vortex motion, resulting in the decrease or increase of the critical current, respectively. We demonstrate a remarkable self-healing effect whereby the magnetic pinning strength for the longitudinal stripes increases with current. The self-field of the current polarizes the magnetic stripes along their width, which enhances the stray fields at their edges and creates a dynamic vortexmore » pinning landscape to impede vortex flow. Our results highlight new strategies to engineer adaptive pinning topologies in superconducting-ferromagnetic hybrids.« less

Simulation model for electron irradiated IGZO thin film transistors

NASA Astrophysics Data System (ADS)

Dayananda, G. K.; Shantharama Rai, C.; Jayarama, A.; Kim, Hyun Jae

2018-02-01

An efficient drain current simulation model for the electron irradiation effect on the electrical parameters of amorphous In-Ga-Zn-O (IGZO) thin-film transistors is developed. The model is developed based on the specifications such as gate capacitance, channel length, channel width, flat band voltage etc. Electrical parameters of un-irradiated IGZO samples were simulated and compared with the experimental parameters and 1 kGy electron irradiated parameters. The effect of electron irradiation on the IGZO sample was analysed by developing a mathematical model.

High throughput analysis of samples in flowing liquid

DOEpatents

Ambrose, W. Patrick; Grace, W. Kevin; Goodwin, Peter M.; Jett, James H.; Orden, Alan Van; Keller, Richard A.

2001-01-01

Apparatus and method enable imaging multiple fluorescent sample particles in a single flow channel. A flow channel defines a flow direction for samples in a flow stream and has a viewing plane perpendicular to the flow direction. A laser beam is formed as a ribbon having a width effective to cover the viewing plane. Imaging optics are arranged to view the viewing plane to form an image of the fluorescent sample particles in the flow stream, and a camera records the image formed by the imaging optics.